Energy Technology Data Exchange (ETDEWEB)

The structure and catalytic properties of 2 wt.-% Pd/SiO/sub 2/ catalysts promoted with 2 wt.-% MgO and 0.2-5 wt.-% iron have been investigated. Catalysts were characterized by TPR, hydrogen chemisorption, and Moessbauer spectroscopy and their catalytic performance in methanol formation was also measured. At 16 at.-% iron a sharp maximum was observed in the activity which can be interpreted as being due to simultaneous promotion with iron and MgO. Independent mechanisms of promotion were found for the two modifiers: iron influenced the metallic component by forming bimetallic PdFe particles while MgO changed the properties of silica in a favourable way. 6 figs., 29 refs., 1 tab.

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

Energy Technology Data Exchange (ETDEWEB)

Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption was possible on minerals that are thought to have been transferred into coal ash. Compound indications of ashes from 29 kinds of ...

Energy Technology Data Exchange (ETDEWEB)

Gas and plasma nitriding processes were executed in the magnesium with modification by titanium in search for an effective surface treatment method for magnesium alloys. Magnesium-nitrogen system has completely no solid solution or solubility, so that nitride should be only formed by eutectic reaction in the liquid phase. Hence, magnesium is difficult or nearly impossible to have its surface modified by nitriding. Addition of nitride forming element into magnesium enables us to lower the onset temperature of nitriding. Magnesium-titanium alloys with 1 to 5 wt% are yielded by the bulk mechanical alloying and, subjected to gas nitriding for various process conditions. Successful co-formation of Mg{sub 3}N{sub 2} as well as TiN becomes a proof to demonstrate the possibility of gas/plasma nitriding in the solid-state magnesium with aid of ...

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The extraction of magnesium by tributyl phosphate from KI solutions was investigated. With increasing KI and TBP concentrations, the extraction increased. The maximum extraction (82%) was attained at pH 4, and it did not decrease with a further pH increase. With decreasing pH, the extraction decreased because of HI extraction. The magnesium was extracted as the compound MgI/sub 2/ x 4TBP. Complexone III (at pH 3-4) does not affect the extraction of magnesium, which makes it possible to use it to mask other metals.

Energy Technology Data Exchange (ETDEWEB)

Various methods for storing hydrogen have been examined in an effort to find ways to store hydrogen in increasingly smaller volumes with decreasing weight of the whole hydrogen storage system. Metal hydrides, in which hydrogen is chemically bound to a metal atom, are considered to be very promising candidates for hydrogen storage because they have high gravimetric and volumetric storage capacities. This study investigated the effect of different magnesium (Mg) and aluminium (Al) ratios on the absorption and desorption properties of thin films. Neutron reflectometry (NR) was used in this study to better understand the absorption and desorption properties of commercially promising hydrogen storage materials. The large negative scattering length of hydrogen atoms changes the reflectivity curve substantially, so that NR can determine the total amount of stored hydrogen as well as the hydrogen distribution along the film normal, with nanometer resolution. In order to ...

Energy Technology Data Exchange (ETDEWEB)

Two aspects of the deformation behavior of magnesium sheets are the subject of this paper. First it will give a mechanical characterization of a commercial magnesium with a focus on the anisotropy and the possible microstructural causes of this behavior. The rolling process will be part of the second aspect. The aim is to show the influence of the parameters on the microstructure and texture and how this could affect the anisotropy in the rolled sheets. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The nature of interaction of some boromagnesium minerals with water is studied, the main stages of interaction are established. The methods of thermo-gravimetric, X-ray phase and chemical analyses are applied to state intermediate and final phases of magnesium borate interaction with water. ''Preobrazhenskite'' - ''inderite'' paragenesis is established. The notion ''magnesium borate solubility'' is shown to be senseless.

Energy Technology Data Exchange (ETDEWEB)

This paper deals with an experimental study of ultra-precision diamond cutting of magnesium alloy (AZ31). In order to investigate the machinability such as the cutting force and the surface integrity and understand the problems in a micro cutting, the experiments on the diamond cutting of magnesium alloy and pure aluminum with an ultra-precision turning machine has been carried out. The machinability of magnesium alloy was compared with that of pure aluminum and discussed. Consequently, both the thrust force component and the surface roughness obtained by cutting of magnesium alloy became larger than that of pure aluminum. It was also found that the inclusions or the defects in the work material caused to generate the scratches on the finished surface and influenced the integrity of mirror surface. (orig.)

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Page 23. Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +/- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +/- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium is known to have poor formability at room temperature, mainly attributed to its hexagonal lattice structure. This paper presents the findings generated from development of warm forming to produce thin-walled magnesium components. Finite element analysis was conducted to evaluate the formability of the material and the simulated results were compared to the tensile results and product formability. Tensile tests were used to verify the formability of the sheet metal at difference temperatures. The process parameters considered in the feasibility study were forming temperature, in the range of 28 C to 300 C and magnesium sheet (AZ31B-H24) thickness, in the range of 0.4 mm to 1 mm. Magnesium hand phone covers of a thickness down to 0.4 mm have been successfully produced. The feasible forming temperature was found to be between 200 C and 250 C. Metallographic examination shows evident of ...

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

Science.gov (United States)

... alloys--Lanthanum-- Magnesium--Magnasium &11oy8--Hagn*31Uft compounds--Manxganese--Manganes. alloys-- Mercury ...

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are ...

International Nuclear Information System (INIS)

One of the major concerns during high speed welding of magnesium alloys is the presence of porosity in the weld metal that can deteriorate mechanical properties. This study seeks to analyze the presence method and quantity of pore during hybrid laser-tungsten inert gas arc (TIG) welding of magnesium alloy AZ31B by radiography, optical microscopy and electron probe microanalysis (EMPA). At the same time, it identifies both the mechanism of pore formation and a remedy for this problem. The experimental results indicate that lacking of shielding gas for laser beam is the dominant cause of macroporosity formation during the hybrid of laser-TIG welding of magnesium Alloys AZ31B plate, and hydrogen is not main cause to form large pores. A favorable weld without porosity can be obtained by appending lateral shielding gas for laser beam.

Energy Technology Data Exchange (ETDEWEB)

In this paper, for an acceleration of utilization of magnesium alloy which is being interested in recent years, friction welding of AZ31 magnesium alloy was carried out, and the joint performance was discussed in relation to the deformation heat input in the upset stage and upset loss as a evaluation factor. Where, the deformation heat input in the upset stage is mechanical work represented by the product of upset speed and axial pressure. As a result, it was made clear that the friction welding of AZ31 magnesium alloy was easy in the atmosphere, and good welded joints without a non- adhesion area at the weld interface could de obtained. Moreover, the evaluation factors discussed were possible to evaluate to joint performance. (orig.)

British Library Electronic Table of Contents (United Kingdom)

A microanalytical characterization of cast magnesium alloys of eutectic origin based on the Mg?Al?Ca ternary matrix system has been carried out in order to investigate the influence of alloying elements on their microstructure as well as microchemistry-processing-microstructural relations using structure-sensitive techniques of electron microscopy, mechanical spectroscopy (internal friction), X-ray diffractometry, and advanced microanalytical methods including electron probe compositional analysis. Following the data obtained here there is direct correlation of microstructure with creep properties of the new experimental magnesium alloys. The creep and heat-induced properties of the multicomponent magnesium alloys containing low range of inexpensive additions of titanium (0.07?0.2%) or str...

Energy Technology Data Exchange (ETDEWEB)

Although magnesium is not attacked by hydrocarbons, it reacts vigorously with anhydrous methanol, raising concerns about the compatibility of the metal with methanol blend fuels. This paper describes the behavior of magnesium alloys in laboratory tests in static contact with methanol-containing fuels at 110/sup 0/F. Water in small concentrations (above 0.25% by weight of the methanol content) is shown to prevent the destructive attack of magnesium by these fuels. The required water content is well within the water tolerance of methanol-GTBA (gasoline grade tertiary-butyl alcohol) cosolvent fuel blends. Die cast AZ91HP shows greater resistance to methanol reaction than does AZ31B sheet.

Energy Technology Data Exchange (ETDEWEB)

A new technique was proposed in order to improve poor corrosion resistance in magnesium. That is, magnesium hydroxide film was formed on the surface of 3 N-Mg by artificial corrosion in 1% MgCl{sub 2} solution for 3.6 ks, which followed by oxidation at 673 K for 3.6 ks in air. Corrosion resistance was evaluated by salt immersion tests in 1% NaCl solution under in situ laser microscopic observations. Bubble evolution, which occurred immediately at the beginning of the immersion test in the case of non-treated specimen, was suppressed by the process. And also, formation of filiform corrosion was suppressed for about 3.6 ks, which occurred at 180 s in the non-treated specimen. (orig.)

Science.gov (United States)

For abstract, see NSA 29 07, number 17945.

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the extrusion characteristics of magnesium alloy (AZ31), a computer simulation was attempted. Tensile properties of as-cast billet with different strain rates were incorporated into the simulation. The results showed a great change in distribution of stress and strain at near die region by the ram travel. It was found that the average grain size at longitudinal edge of the extruded sheet was smaller than that at center region, which might be attributed to recrystallization caused by severe plastic deformation. (orig.)

International Nuclear Information System (INIS)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

Energy Technology Data Exchange (ETDEWEB)

PVD-chromium-nitride coated samples of substrates of the magnesium alloy AZ91hp and the roller and ball bearing steel 100Cr6 were investigated regarding structure, mechanical characteristics, adhesion and internal stresses. For the coatings the parameters layer thickness and substrate BIAS voltage were varied. Both substrate materials were coated in one lad. Results of the X-ray analysis of the internal stresses show significant differences between the coated magnesium and the coated steel substrates. In the case of the variation of the substrate BIAS voltage, for the coated steel a dependency of the internal stresses to coating parameters could be obtained. For the coated magnesium no dependency was recognizable. The coating structure was examined with scanning electron microscopy. Element depth profiles of the coated samples were performed with SIMS. (orig.)

UK PubMed Central (United Kingdom)

The authors report a case of a cephalopagus conjoined twin that was diagnosed at 29 weeks of gestation despite the mother having had two ultrasounds done previously. The fetus had one head and face,...Full Text Available

Science.gov (United States)

... Scientists. NASA/DoD Aerospace Knowledge Diffusion Research Project. Descriptive Note : Technical memo. rept. no. 29,. ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are ideal candidates to benefit from equal channel angular extrusion (ECAE) because of their poor forming characteristics due to a hcp structure. In this study, ECAE processing was applied to ZK31 and AZ31 magnesium alloys under various conditions. The grain size of as-ECAE specimens decreases with decreasing the processing temperature, however, the grain size decreases slightly with increasing number of repetitive processing. Both the tensile strength and 0.2% proof stress of as-ECAE specimens are high when processed at low temperature, but the elongation is high when processed at high temperature. Crystal orientation is different in the two alloys and it also varies according to the processing temperature for the two alloys. The difference of the crystal orientation influences the tensile properties, especially 0.2% proof stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Biological cells of the nitrogen fixating bacteria Xanthobacter autotrophicus GZ 29 have been cultivated with 57-Fe, and from the nitrogenase of these cells the 57-Fe marked molybdenum-iron-protein is extracted. The Moessbauer spectra of this enzyme show that the structure of the iron cluster is similar to the structure in the molybdenum-iron-proteins of Azotobacter vinelandii, Klebsiella pneumoniae or Clostridium pasteurianum.

International Nuclear Information System (INIS)

Hybrid organic-inorganic coatings with phosphonate functionalities have been synthesized and evaluated as prospective surface treatments for magnesium materials. These coatings have been processed via a sol-gel route by hydrolysis and condensation of a mixture of diethylphosphonatoethyltriethoxy-silane and tetraethoxy-silane with variable molar ratios. The coatings morphology and the surface chemistry at the coating/substrate interface have been characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, "3"1P nuclear magnetic resonance spectroscopy, and time-of-flight secondary ion mass spectrometry. The corrosion protection performance of the coatings deposited on magnesium alloy AZ31B has been examined by a group of electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, a scanning Kelvin probe technique has been used to investigate interfacial ...

Science.gov (United States)

... having high fluidity. The SC-51A alloy contains 4.5 to 5.5% silicon, 1 to 1.5% coppers .4 to .6% magnesium, o35% sine, .8% iron, .5% manganes*, ...

Science.gov (United States)

The effects of various fixative agents, pH, ionic strength, stain concentration, and magnesium concentration on DNA staining with the antibiotics olivomycin, chromomycin A3, and mithramycin were examined with DNA in solution and in mammalian cells.

Science.gov (United States)

The biocompatibility and corrosion resistance of various materials for use as sacrificial anodes in in vivo hybrid fuel cells were studied. Aluminium, zinc, and magnesium alloy AZ31B were studied, and the results are discussed.

Energy Technology Data Exchange (ETDEWEB)

Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

To investigate the influence of equal channel angular pressing on the microstructure and texture of the magnesium alloy AZ31, electron backscattering diffraction and well as neutron diffraction experiments were carried out. Through these experiments it was possible to trace the microstructure and texture evolution with strain accumulated with the increasing number of equal channel angular pressing passes. It was further demonstrated by subsequent compression tests that the microstructural changes produced by equal channel angular pressing have a beneficial effect on both the compressive strength and ductility of AZ31. (orig.)

International Nuclear Information System (INIS)

The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society

Science.gov (United States)

29 matches ... 09.20.1999. FOX SPORTS TELEVISION CREW TAPING SEGEMENT IN VISITOR CENTER + More Details. 10.23.2010. USA Science and Engineering Festival ...

Science.gov (United States)

... 3122.01A, Joint Operation Planning and Execution System (JOPES) Volume I, Planning Policies and Procedures (Sept. 29, 2006) and CJCSM ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... Law Parameter 28 Summary 28 6. CIRCULAR VS ANNULAR LASER BEAMS 29 7. HIGH-ENERGY LASER BEAM PROPAGATION THROUGH A ...

Science.gov (United States)

... Joint Publication (JP) 5-0 (Washington DC: CJCS, 29 September ... and Execution System (JOPES) Volume 1. CJCSM 3122.01A (Washington, DC: 6 ...

Science.gov (United States)

any locality that is now in the United States. The English fleet lies at anchor, the infantry troops having disembarked and are attacking the Spanish settlement on May 28 and 29,...

British Library Electronic Table of Contents (United Kingdom)

Colon cancer is one of the leading causes of death and a major public health problem in western countries. We examined the isoflavone content of 70% ethanol extract of soy germ (SG) and its apoptotic effect in HT-29 colon cancer cells. Our results showed that the major isoflavones of the SG extract were daidzein and genistein, and it effectively induced apoptosis in HT-29 cancer cells. In addition, nuclear factor-kappa B (NF-kB) expression was reduced in cells treated with the SG extract, which reduced cyclooxygenase-2 (COX-2) and nitric oxide synthase (iNOS) expression. These combined effects ultimately resulted in apoptosis via caspase-3 activation. In addition, daidzein and genistein, the major isoflavones of SG extract, also exerted the apoptotic effect against HT-29 cancer cells. Thes...

Science.gov (United States)

assessment.Both frustumswerein excellentcondition.No missingTPSor debonds/ unbondswere ...... 2) The average time for a 360 degree rotation was 29.9 seconds. ...

Science.gov (United States)

Valve Flow Characteristics. 3-68. 3-40. Valve Operating Current Vs. Temperature ...... VALVE FLOW CHARACTERISTICS. Acceptance Test 4/29/74. SINs 002 & 004 ...

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

The experiment was carried out on a short rotation coppice culture of poplars (POP-EUROFACE, Central Italy), growing in a free air carbon dioxide enriched atmosphere (FACE). The specific objective of this work was to study whether elevated CO{sub 2} and fertilization (two CO{sub 2} treatments, elevated CO{sub 2} and control, two N fertilization treatments, fertilized and unfertilized), as well as the interaction between treatments caused an unbalanced nutritional status of leaves in three poplar species (P. x euramericana, P. nigra and P. alba). Finally, we discuss the ecological implications of a possible change in foliar nutrients concentration. CO{sub 2} enrichment reduced foliar nitrogen and increased the concentration of magnesium; whereas nitrogen fertilization had opposite effects on leaf nitrogen and magnesium concentrations. Moreover, the interaction between elevated CO{sub 2} and N fertilization amplified some element unbalances such ...

Energy Technology Data Exchange (ETDEWEB)

There are many factors affecting diffusion bonding in order to obtain high quality joining. Therefore, in the beginning, we constructed diffusion bonding model based on void growth mechanism to predict bonding pressures and times. In addition, in order to compare theoretical values with experimental values, diffusion bonding tests were carried out by using commercial AZ31 magnesium alloy sheets with different grain sizes, 16 and 130 {mu}m. The present AZ31 alloys were successfully diffusion bonded at several conditions, and the bonding strength was more than 0.8 of each parent materials. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This research investigated the inhibiting effects that sodium salts of linear monocarboxylic acids displayed towards the corrosion process of AZ31 Mg alloy in ASTM D 1387 saline solution (a synthetic industrial cooling water). The length of the aliphatic chain of the acids ranged between 7 and 15 carbon atoms. The inhibiting action of these salts can be related to the precipitation of an insoluble magnesium salt, which mainly affected the anodic reaction. The aliphatic chain length controlled the anion solubility and the reaction rate of magnesium carboxylate formation. For all the salts, an optimum concentration was experienced: 10{sup -2} M for sodium decanoate (caprate), 10{sup -3} M for sodium dodecanoate (laurate), 10{sup -4} M for sodium tetradecanoate (myristate); when this concentration was exceeded, a diminution (even a disappearance) in the inhibiting action was found. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

International Nuclear Information System (INIS)

Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.

Energy Technology Data Exchange (ETDEWEB)

Dynamic development of new grain boundaries was studied in compression of a magnesium alloy AZ31 with initial grain sizes (D{sub 0}) of 22 {mu}m and 90 {mu}m at a temperature of 673 K. Kink bands are evolved near corrugated grain boundaries and in grain interiors at low strains accompanied with new fine grains. Kink bands are developed often perpendicular to the basal plane. The boundary misorientation of kink band as well as the volume fraction of new grains increases rapidly with increasing strain and approaches a saturation value in high strain. New fine grains are developed faster with decrease in the D{sub 0}. It is concluded that new grain evolution is controlled by a deformation-induced continuous reaction, i.e. continuous dynamic recrystallization (DRX). (orig.)

International Nuclear Information System (INIS)

A method is described for determination of aluminium, cadmium, cobalt, chromium, copper, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, zinc, titanium and vanadium in iron ore. After dissolution, a 1 gram sample of iron ore is applied to a column of AGI-X8 anion exchange resin (chloride form), in 100 ml of 7M HCl. Aluminium, chromium, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, titanium and vanadium are eluted with 7M HCl; iron, copper and cobalt are eluted with 0.5M HCl; cadmium and zinc are eluted with 2M HNO_3. Iron is subsequently removed from copper and cobalt by a solvent extraction with methyl isobutyl ketone. The elements are determined in the eluates by atomic absorption spectrometry, except for titanium and vanadium, which are determined spectrophotometrically.

UK PubMed Central (United Kingdom)

A 269-kilobase conjugative plasmid, pK29, from a Klebsiella pneumoniae strain was sequenced. The plasmid harbors multiple antimicrobial resistance genes, including those encoding CMY-8...Full Text Available

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and ...

Science.gov (United States)

A number of alloys of zirconium have been investigated as part of a program aimed at improving the high-temperature tensile and creep strength of zirconium. These alloys include aluminum, beryllium, lead, magnesium, molybdenum, niobium, tantalum, tin, titanium, tungsten, vanadium, and zinc, binary and ternary alloys. The data indicate that aluminum, lead, molybdenum niobium, tin, titanium, tungsten, and vanadium can be used successfully to harden zirconium, and that aluminum, tin, titanium, and vanadium are particularly effective in maintaining the strength of zirconium at elevated temperatures.

Energy Technology Data Exchange (ETDEWEB)

Nutrient elements contained in litter fall flux, that of uptake flux and turnover rate had generally tended to increase with the increase in the Warmth Index, while the amount of nutrient in the A[sub 0] horizon and nutrient use efficiency did not. However, it is suggested that topographic and climatic aridity, and the amount of available and exchangeable phosphorus, calcium and magnesium greatly affect the nutrient dynamics in a each forest ecosystem as the Warmth Index increases. (J.P.N.).

International Nuclear Information System (INIS)

Dynamic recrystallization (DRX) is the main softening mechanism of magnesium alloy AZ31B in hot deformation. Theoretically, in the flow rule the atomic diffusibility and the driving force of dislocation migration are dependent on the temperature, and the dislocation density and the cumulation of grain boundary energy are dependent on the strain rate. The peak stress will appear when the flow driving force and resistance force reach a balance, after which the stress descending will take place due to recrystallization fraction. Since the DRX is a thermally activated process, the recrystallized volume fraction can be regarded as the function of strain through Avrami equation. Based on this idea, the paper proposes a new constitutive model characterizing dynamic recrystallization for magnesium alloy AZ31B. The model is described by a peak stress and a strain softening rate, in which the peak stress depends only on Zener-Hollomon parameter and is ...

British Library Electronic Table of Contents (United Kingdom)

A range of 6-substituted imidazo[1,2-a]pyridines were synthesized using a multicomponent coupling reaction. Most of these compounds were found to exhibit excellent activity against the colon cancer cell lines HT-29 and Caco-2, whilst not showing significant toxicity against white blood cells. Our studies have shown that the proteolytic phase of apoptosis was initiated 2 h after treatment with these imidazo-[1,2-a]pyridines. The data suggests that the imidazo[1,2-a]pyridine-induced cell death in HT-29 and Caco-2 cells is mediated via pathway(s) that include the release of cytochrome c from the mitochondria to the cytosol and the activation of caspase 3 and caspase 8.

International Nuclear Information System (INIS)

Polish 2010 p. 101 Poland Gradzka, I. Sochanowicz, B. Wojewodzka,

Energy Technology Data Exchange (ETDEWEB)

The results of a search for fractionally charged particles produced in e/sup +/e/sup -/ annihilation at 29 GeV/c/sup 2/ are discussed. Results from cosmic-ray searches for fractionally charged particles, tachyons, and massive particles using the same detector are also presented.

Energy Technology Data Exchange (ETDEWEB)

The energy strategy of the UK Overseas Development Administration is outlined with specific emphasis on energy efficiency and renewable energies. Based on 29 case studies concerning projects and programmes in both developed and developing countries, critical success factors for renewable energy projects are identified. UK)

UK PubMed Central (United Kingdom)

Phenothiazine-N-carbonyl chloride inactivated chymotrypsin and trypsin by means of a 1:1 stoicheiometric reaction. Its reaction with chymotrypsin was 29 times as fast as that with...Full Text Available

Science.gov (United States)

million for advanced energy projects Thu, Sep 29, 2011 - Project Aims to Bring Bio-based Jet Fuel Production to the Northwest Mon, Sep 12, 2011 - Drive like the wind Thu, Aug 25,...

UK PubMed Central (United Kingdom)

Enteropathogenic bacteria was isolated from 131 of 447 (29.4%) neotropical Panamanian lizards belonging to 34 species of seven families. Overall, 147 strains of bacteria were isolated comprising 26...Full Text Available

Science.gov (United States)

Typical aircraft types supported include F4-Phantom, Tornado, MiG-29 ...... attempt to develop a theoretical explanation for learning phenomena [16]. ..... perspective, a primary reason for this is that an exponential curve approximates ...

Wastenet

...11 23861 767 23917 3 Journal of Economic Growth, Springer 29.093 6313 217 6438 4 Econometrica, Econometric Society 28.104 89847 3197 91067 5 Review of ...

UK PubMed Central (United Kingdom)

Every year nearly 200,000 men in the United States are diagnosed with prostate cancer (PCa), and another 29,000 men succumb to the disease. Within certain regions of the world population based...Full Text Available

UK PubMed Central (United Kingdom)

Colonies of toxin-producing Pasteurella multocida were detected with peroxidase-labeled monoclonal antibodies by a membrane assay. Examination of the specificity of the assay with 29 P. multocida cultures...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This official IEA report is a deliverable of IEA SHC Task 21/IEA BCS Annex 29: Daylight in Buildings. The Task focuses on daylighting systems and strategies which can be applied in new and existing buildings with a high potential electricity saving potential such as offices, schools, commercial, and institutional buildings. The daylighting performance of these strategies and systems is tested in laboratory facilities, through modeling, and in real case study buildings. This paper provides methods and procedures to evaluate the daylighting performance of real buildings. Annex 29 case studies located in Europe, North America, and Australia. It is a deliverable of Subtask D research projects. The main objective of Subtask D, as stated in the Implementing Agreement of Task 21/Annex 29, is `to demonstrate the viability of daylighting buildings in various world climatic zones as a means of achieving significant improvements in ...

UK PubMed Central (United Kingdom)

In 29 patients with urinary obstruction due to prostatic enlargement, medium-fill water cystometry was performed before prostatectomy and again 3 months after. A high incidence of detrusor hyperreflexia...Full Text Available

UK PubMed Central (United Kingdom)

SummaryDNA-based tests are increasingly being used to predict a blood group phenotype. This is possible because genes encoding 29 of the 30 blood group systems have been cloned and sequenced,...Full Text Available

UK PubMed Central (United Kingdom)

Crockford, G. W., Crowder, M., and Prestidge, S. P. (1972).Brit. J. industr. Med.,29, 378-386. A trace gas technique for measuring clothing microclimate...Full Text Available

Science.gov (United States)

...treated for leukemia. B' s physician, who is employed by the HMO, is considering a treatment plan that includes six-mercaptopurine, a drug for treating leukemia in most children. However, the drug could be fatal if taken by a small percentage of...

Science.gov (United States)

...retardation, behavioral disorders or...blood. (3) Health protection goals...protecting your health. You are strongly...an independent analysis. The two...impairment of health. One of...although most cases of lead-induced...in the form of behavioral...

Energy Technology Data Exchange (ETDEWEB)

This report describes the activities conducted with DOE funds at Oregon Health Sciences University between 9/15/94 and 9/29/99. The activities fall into four major categories: Information Technology, Information Services and Support, Medical Informatics and Outcomes Research, and collaboration with other institutions. The focus of these activities was to implement and maintain a regional healthcare information network.

International Nuclear Information System (INIS)

To investigate the growth inhibitory effects, and the underlying mechanism of human colon cancer cell (HT-29) death, induced by a new synthetic bile derivative (HS-1200). Human colon cancer cells (HT-29), in exponential growth phase, were treated with various concentrations of a new synthetic bile acid derivative (HS-1200). The growth inhibitory effects on HT-19 cells were examined using a trypan blue exclusion assay. The extent of apoptosis was determined using agarose gel electrophoresis, TUNEL assays and Hoechst staining. The apoptotic cell death was also confirmed by Western blotting of PARP, caspase-3 and DNA fragmentation factor (DFF) analysis. To investigate the involvement of mitochondria, we employed immunofluorescent staining of cytochrome c and mitochondrial membrane potential analyses. The dose required for the half maximal inhibition (IC_5_0) of the HT-29 cell growth was 100 #approx# 150 #mu# M of HS-1200. ...

Energy Technology Data Exchange (ETDEWEB)

Stearic acid gel is employed to study the phase evolution of MgTiO{sub 3} nanoparticles by thermal gravimetric analysis, X-ray diffraction, and Fourier transform infrared. During the preparation of stearic acid gel, tetrabutyl titanate easily absorbed moisture to hydrolyze into Ti(OH){sub 4} firstly, and then reacts with stearic acid and magnesium stearate to form magnesium-titanium oxide network polymer gel, meanwhile n-butanol is generated. When stearic acid gel is calcined in air, a series of oxidation and combustion reactions occur, meanwhile apparent heat is given off. The results show that a metastable intermediate phase Mg{sub 2}TiO{sub 4} is generated at 450 {sup o}C and nearly disappeared at 550 {sup o}C. Simultaneously, a new solid phase of MgTiO{sub 3} appears. The metastable intermediate phase Mg{sub 2}TiO{sub 4} is successfully identified in the current work.

Energy Technology Data Exchange (ETDEWEB)

In this study, isothermal torsion tests were carried out on magnesium AZ31B alloy under constant strain rate conditions, in the range of 250 to 400 C at 0.01, 0.1, and 1.0 s{sup -1}. Alloy flow stress dependence on strain rate and temperature can be described by a power law with activation energy of 130 kJ/mol. Microstructural examination of hot deformed samples shows very fine recrystallized grains decorating grain boundaries of larger gains in the form of a necklace. These fine grains are produced by dynamic recrystallization at the grain boundaries of original grains. Microstructure evolution, based on samples quenched at different strain levels, indicates that increasing deformation strain has little effect on recrystallized grain size but widens the recrystallized region, with full recrystallization achieved at a certain high strain level. Recrystallized grain size increases with increasing deformation temperature and strain rate. The latter suggests ...

Energy Technology Data Exchange (ETDEWEB)

The tensile and compressive properties as well as LCF and HCF performance of the extruded magnesium alloys AZ31 and AZ80 were determined in extrusion (L) and long-transverse (T) directions. Owing to marked crystallographic textures, both alloys showed pronounced directional mechanical properties in monotonic as well as cyclic loading with strength values in L-direction being significantly superior to those in T-direction. Thermomechanical treatments such as pressing, swaging and rolling were found to increase yield stresses and HCF strengths and to alter the directionality in properties due to textural modifications. To further improve HCF strengths, mechanical surface treatments such as shot peening, roller-burnishing and deep rolling were utilized. The results indicate marked improvements provided that suitable process parameters are used. The improvement of the HCF strengths is explained by the process-induced changes in near-surface dislocation densities and ...

Energy Technology Data Exchange (ETDEWEB)

Three kinds of thin AZ31 wrought magnesium alloys sheets were used in order to investigate the influence of the second phase particles on fracture toughness. From the theoretical model, the ratio of {lambda}{sub p}/d{sub p} would be estimated 5 {proportional_to} 6. On the other hand, from the microstructural observation, average particle spacing on each material was sample A: 13.1 {mu}m, sample B: 14.1, and sample C: 12 {mu}. In addition, average particle size on each sample was sample A: 2.1, sample B: 1.9, and sample C: 2.3 {mu}m. Therefore, the ratio of {lambda}{sub p}/d{sub p} calculated from fracture surface observation would be predicted 6 {proportional_to} 7. In comparison with the result of the prediction by theoretical analysis was in good agreement with the result of fracture toughness observation. It was found that the variation in plane-strain fracture toughness on AZ31 were affected by both of particle spacing and particle size. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The deformation behavior and structure changes of magnesium alloy AZ31 were studied in compression at temperatures ranging from 523 K to 673 K and at a strain rate of 3 x 10{sup -3} s{sup -1}. They depend sensitively on deformation temperature. At high temperatures, grain fragmentation takes place due to frequent formation of kink bands initially at corrugated grain boundaries and then in grain interiors, followed by full development of new grains in high strain. At lower temperatures, in contrast, twinning takes place in rather coarse grains and kink bands are formed mainly in finer original ones in low strain. It is concluded that new grain evolution can be controlled by a deformation-induced continuous reaction resulting in grain fragmentation by kink bands, i.e. continuous dynamic recrystallization (cDRX). The latter is discussed comparing with conventional, i.e. discontinuous, DRX. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The effect of ammonia treatment in field natural rubber (NR) latex with different storage period time on the properties of concentrated NR latex and stability of skim latex was investigated. Fresh NR latex was treated with various ammonia contents such as 0.35, 0.60 and 0.80% w/w, and then they were centrifuged to get the concentrated NR latex with 60% dry rubber content (DRC) containing 0.16, 0.18 and 0.25% w/w, respectively and skim NR latex with roughly 5% DRC containing 0.42, 0.60 and 0.80% w/w, respectively. The effect of storage times with ?0, 15, 30 and 45 days for concentrated NR latex with different ammonia contents on their properties such as alkalinity, magnesium content and viscosity was observed. It was found that generally, magnesium content in field NR latex and latex...

Energy Technology Data Exchange (ETDEWEB)

The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was also influenced by the test orientation. Metallographic studies revealed a ...

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

Energy Technology Data Exchange (ETDEWEB)

This specification establishes requirements for design, testing, and quality assurance for electric heaters that will be used to maintain primary Sodium temperature in the Fast Test Facility (FFTF) reactor vessel. The Test Specification (WHC-SD-FF-SDS-003) has been revised to Rev. 1. This change modifies the fabrication of approximately 25 feet of the subject heater using ceramic insulators over the heater lead wire rather than compressed magnesium oxide. Also, 304 or 316 stainless steel can be used for the heater sheath. This change should simplify fabrication and improve the heater operational reliability.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

International Nuclear Information System (INIS)

The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.

Science.gov (United States)

INTRODUCTION. We searched for a pathophysiologically based feature of major water electrolytes, which may define water quality better than the water hardness, respecting urinary calculus formation. MATERIALS AND METHODS. Utilizing a multistage stratified sampling, 2310 patients were diagnosed in the imaging centers of the provincial capitals in Iran between 2007 and 2008. These were composed of 1755 patients who were settled residents of 24 provincial capitals. Data on the regional drinking water composition, obtained from an accredited registry, and their relationships with the region's incidence of urinary calculi were evaluated by metaregression models. The stone risk index (defined as the ratio of calcium to magnesium-bicarbonate product in drinking water) was used to assess the risk of calculus formation. RESULTS. No correlation was found between the urinary calculus incidence and the amount of calcium, bicarbonate, or the total hardness of the drinking water. ...

International Nuclear Information System (INIS)

HT-29 human colon tumor cells growing as spheroids have been evaluated as a model system for measuring the response of human colon tumor cell to antineoplastic agents. HT-29 cells have been capacity to form spheroids up to 1 mm or more in diameter when grown in spinner culture. The multicellular HT-29 spheroids develop hypoxic centers reflecting the cellular conditions found in human cancer treatment, i.e., nutritionally deficient hypoxic cells that are felt to be a significant source of both radiation and chemotherapy clinical treatment failures. Spheroids of increasing size were radiated and then dispersed into single cells for colony survival assay. Compared with irradiated single cell suspensions, the spheroid cells demonstrated a significant increase in radioresistance. Growing spheroids developed a complex radiation survival curve which was variable with respect to size of the spheroid. The drug 5-Fu was studied to ...

CERN Document Server

Galactic open clusters are since long recognized as one of the best tools for investigating the radial distribution of iron and other metals. We employed FLAMES at VLT to collect UVES spectra of bright giant stars in a large sample of open clusters, spanning a wide range of Galactocentric distances, ages, and metallicities. We present here the results for four clusters: Berkeley 20 and Berkeley 29, the two most distant clusters in the sample; Collinder 261, the oldest and the one with the minimum Galactocentric distance; Melotte 66. Equivalent width analysis was carried out using the spectral code MOOG and Kurucz model atmospheres to derive abundances of Fe, Al, Mg, Si, Ca, Ti, Cr, Ni, Ba; non-LTE Na abundances were derived by direct line-profile fitting. We obtain subsolar metallicities for the two anticenter clusters Be 20 ([Fe/H]=-0.30, rms=0.02) and Be 29 ([Fe/H]=-0.31, rms=0.03), and for Mel 66 ([Fe/H]=-0.33, rms=0.03), located in the ...

Energy Technology Data Exchange (ETDEWEB)

A study was undertaken of the effect of monovalent cations (Li/sup +/, Na/sup +/, K/sup +/) on the dielectric constant (epsilon) of the water-lipid interface of unilamellar phosphatidylcholine (PC) vesicles, i.e., the ester carbonyl oxygen region of the PC molecules or the neighborhood of the oxygen atoms of the phosphorylcholine moiety. epsilon was determined by reacting the free radical 1,1-diphenyl-2-picrylhydrazyl with ..cap alpha..-tocopherol incorporated in the lipid vesicles. The results are consistent with a decrease of epsilon (LiCl: 35.5 to 29.5; NaCl: 34 to 29; KCl: 33 to 29) as the concentration of the salts in the solvent media increases from 0.025 to 0.5 M. These effects can be rationalized in terms of dielectric saturation at the water-lipid interface brought about by ion-induced local electric fields. In the unilamellar PC vesicles the effect of the ions on epsilon follows the sequence K/sup +/ > Na/sup ...

International Nuclear Information System (INIS)

The specific receptor sites and the endocytosis of transferrin (Tf) are evidenced in a cell line (HT-29) derived from a human colic adenocarcinoma by means of "1"2"5I radiolabeled Tf. The receptor density is studied in undifferentiated (UD) or differentiated (D) cells with respective doubling times of about 24 hours and 46 hours. The number of binding sites for Tf is 162,000 (K_d = 7.8 nmol/l in ND cells and 68,000 (K_d = 7.40 nmol/l) in D cells. The distribution between the Tf bound to the cell surface and the internalized Tf is investigated by elimination of Tf bound to the surface by an acid wash method. The intracellular cycle of Tf seems to be characterized by a slower kinetics in UD cells. The high density of Tf receptor sites in HT-29 UD cells should allow the detection or the treatment of highly evolutive colic adenocarcinoma by means of Tf.

International Nuclear Information System (INIS)

Two no-carrier-added "1"2"5I-labelled photoaffinity rapamycin analogs were prepared: 7-demethoxy-7-(4-azido-3-"1"2"5I-benzyloxy) rapamycin and its C_2_8-C_2_9 seco analog. The key reactions of the synthesis were substitution of the C_7 methoxyl of rapamycin with 4-azido-3-tributylstannylbenzyloxy group, exchange of tributyltin with "1"2"5I using Na"1"2"5I and Chloramine-T, and a ZnCl_2 mediated retro-Aldol cleavage of the C_2_8-C_2_9 bond of rapamycin. (author).

Energy Technology Data Exchange (ETDEWEB)

Radon concentration measurements at 50 locations in the monitoring network at Canonsburg, Pa., are reported for the quarterly period of April 29 to July 28, 1980. In addition, a summary of all data from the date of initiation of the network (covering the period January 29 to July 28, 1980) is presented for comparison purposes. Average background in the Canonsburg area for the quarterly period was 0.21 pCi/liter with a range of 0.16 to 0.26 pCi/liter. This compares with an average for the first quarter of 0.18 pCi/liter and a range of 0.12 to 0.23 pCi/liter. Concentrations ranging from 0.27 to 0.75 pCi/liter at 17 locations exceeded the background range. These locations are predominantly downwind of the site in an easterly direction. A similar pattern is evident from the summary of data for the first two quarters.

British Library Electronic Table of Contents (United Kingdom)

Premnalatifolin A (1), a unique icetexane diterpene dimer was isolated from the stem-bark of Indian medicinal plant, Premna latifolia. Its structure and relative stereochemistry were elucidated on the basis of detailed spectroscopic analysis, including HRESIMS and 2D NMR (COSY, HSQC, HMBC, and NOESY) spectra. The compound has dimeric carbon skeleton composed of two icetexane skeletal diterpenes linked via ether bond. Further, premnalatifolin A (1) was also evaluated for its cytotoxicity against cancer cell lines (HT-29, A-431, MCF-7, Hep-G2, PC-3, A-549, B-16 F10, and ACHN), which displayed potent activity against HT-29 and MCF-7 cell lines with the IC50 values of 12.15 and 1.11mg/mL, respectively.

DEFF Research Database (Denmark)

Pro-inflammatory cytokines may directly influence the viability and metabolic function of colonic epithelial cells (CEC) as an early event in the development of inflammatory bowel disease. We report here that TNF-alpha+IFN-gamma induced a synergistic, concentration-dependent decline in butyrate oxidation, an essential energy supply, in HT-29 and DLD-1 cells. TNF-alpha+IFN-gamma induced a parallel profound decline in cell viability in HT-29 cells, but not in DLD-1 cells, where impairment of butyrate oxidation seemed to precede later occurrence of cell damage. TNF-alpha+INF-gamma induced CEC damage was independent on NO formation and involved the IFN-gamma signalling pathway as well as induction of apoptosis. If cytokines have similar effects in vivo, these may lead to energy deficiency and thus contribute to CEC damage and disturbance of the epithelial integrity.

Energy Technology Data Exchange (ETDEWEB)

Composting of sawdust and paper mill sludge, using a 'Kneer' process reactor, was studied in an attempt to elaborate upon organic matter transformation during the process and to define parameters to measure the compost maturity level. Temperature, electron paramagnetic resonance data, ash and C, H, N and S contents, and a spectroscopic method using ultraviolet-visible (UV-VIS) for alkaline (pH = 8.5) and solid samples was used to study the maturity of the compost samples. These parameters were measured in 6 humic acids extracted from the compost samples during 29 days. The results of this work show that the 'Kneer' process is efficient in transforming ligno-celulitic residues in a short time (29 days), into an organic fertilizer material with application perspectives (author)

International Nuclear Information System (INIS)

Heat capacities and densities of aqueous MgCl/sub 2/, CaCl/sub 2/, and SrCl/sub 2/ from the accompanying paper are combined with literature data up to 473 K to yield temperature-dependent equations by using the ion-interaction model of Pitzer. These heat capacity equations have been integrated to yield the enthalpy and the Gibbs energy. The enthalpy parameters for 298 K are evaluated in separate calculations using published high-temperature osmotic data as well as heats of dilution, while the Gibbs energy parameters for 298 K are taken from the literature. The range of validity of the final equations is described.

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

International Nuclear Information System (INIS)

This pilot project was carried out for the purpose of testing methods for active biological monitoring. It covered a period of three years (until September 1994), including two years of exposure. The measurements served to determine pollutant levels in plants used as animal fodder and dust-borne heavy metal concentrations in different sites and, on this basis, to obtain indirect information on human exposure. Among others, the pilot project investigated the suitability of Italian rye-grass as a biological indicator for aluminium, arsenic, cadmium, cobalt, chromium, copper, iron, mercury, magnesium, manganese, nickel, lead, platinum, antimony, titanium, and zinc. (orig./GL).

British Library Electronic Table of Contents (United Kingdom)

Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...

International Nuclear Information System (INIS)

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 ?m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

Energy Technology Data Exchange (ETDEWEB)

Materials for the construction of cold neutron sources must satisfy a range of demands. The cryogenic temperature and irradiation create a severe environment. Candidate materials are identified and existing cold sources are briefly surveyed to determine which materials may be used. Aluminum- and magnesium-based alloys are the preferred materials. Existing data for the effects of cryogenic temperature and near-ambient irradiation on the mechanical properties of these alloys are briefly reviewed, and the very limited information on the effects of cryogenic irradiation are outlined. Generating mechanical property data under cold source operating conditions is a daunting prospect. It is clear that the cold source material will be degraded by neutron irradiation, and so the cold source must be designed as a brittle vessel. The continued effective operation of many different cold sources at a number of reactors makes it clear that this can be accomplished. 46 refs., 8 ...

Energy Technology Data Exchange (ETDEWEB)

In the present study, element interdiffusions at the cofired interface of 9/1 Ag/Pd electrode and lead magnesium niobate (PMN)-based ferroelectrics were investigated using Auger Electron Spectroscopy (AES). Intense interdiffusions at the interface were observed while Ag and Pd could penetrate into the ceramics for about 1 {mu}m. Ag-doping experiments were carried out to further study the effects of Ag diffusion on electrical properties of the ceramics. The results showed that Ag could be incorporated into solid solution of the ceramics as Ag{sup +}. As a whole, the Curie temperature (Tc) and dielectric constant of the ceramics decreased with Ag addition. However, Ag addition had no obvious effect on the insulation resistivity. The results inferred that Ag{sup +} could substitute for Pb{sup 2+} at A site of ABO{sub 3} lattice, thereby oxygen vacancies were generated.

International Nuclear Information System (INIS)

The microstructure of commercial rolled magnesium alloy AZ31B (nominal composition Mg-3Al-0.9Zn-0.15Mn in wt.%) was investigated with the help of light microscopy, electron backscatter diffraction (EBSD) and X-ray diffraction technique after annealing in the temperature range from room temperature (RT) to 400 deg. C. Tensile tests at RT were performed to show the influence of the microstructure on mechanical properties. Static recrystallization (SRX) was observed during annealing of as-received alloy at and above 150 deg. C. Twins play an important role during SRX and serve as nucleation sites and preferred paths for growth of grains. The strong basal texture caused by rolling was weakened by SRX. Significant differences in the stress strain curves were observed for as-received and annealed specimens.

International Nuclear Information System (INIS)

The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic slip systems.

British Library Electronic Table of Contents (United Kingdom)

A novel approach using reactive processing is explored that eliminates the labour-intensive separation of post-consumer polyolefin waste from the mixed plastics waste stream. The reactive compatibiliser BMI has been used to form a modified blend of PCPW with 40% improved tensile strength relative to the uncompatibilised control. Addition of 60 wt.-% magnesium hydroxide [Mg(OH)2] during reactive compatibilisation with BMI gave rise to an even more significant enhancement (up to 100%) of the tensile strength. BMI was also able to usefully enhance the properties of a composite based on calcium carbonate and the polyolefin waste.

International Nuclear Information System (INIS)

The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples.

Energy Technology Data Exchange (ETDEWEB)

Effects of ions of Group IA, IIA, IIIB, and VIIB elements on the cathodic deposition of a molybdenum were investigated in a KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt at 773 K (500/degree/C). The results can be summarized as follows: The addition of potassium, rubidium, cesium, and barium cations and fluorine anions to the KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt is effective in depressing the cathodic deposition of the molybdenum subchloride, which hinders the smooth, flat electrodeposition of molybdenum. The addition of lithium, sodium, magnesium, calcium, strontium, and aluminum cations and bromine and iodine anions promotes the undesirable cathodic deposition of the molybdenum subchloride.

International Nuclear Information System (INIS)

A #lambda#gt11 cDNA library was constructed from poly(U)-Spharose-selected Entamoeba histolytica trophozoite RNA in order to clone and identify surface antigens. The library was screened with rabbit polyclonal anti-E. histolytica serum. A 700-base-pair cDNA insert was isolated and the nucleotide sequence was determined. The deduced amino acid sequence of the cDNA revealed a cysteine-rich protein. DNA hybridizations showed that the gene was specific to E. histolytica since the cDNA probe reacted with DNA from four axenic strains of E. histolytica but did not react with DNA from Entamoeba invadens, Acanthamoeba castellanii, or Trichomonas vaginalis. The insert was subcloned into the expression vector pGEX-1 and the protein was expressed as a fusion with the C terminus of glutathione S-transferase. Purified fusion protein was used to generate 22 monoclonal antibodies (mAbs) and a mouse polyclonal antiserum specific for the E. histolytica portion of the fusion protein. A ...

Energy Technology Data Exchange (ETDEWEB)

This book covers representative projects in each program within the Department of Energy. The projects included were selected to provide an insight into the wide spectrum of projects authorized and under way in the Department. The projects described do not cover all projects authorized - they are merely representative. Descriptions, goals, and status are given for 29 energy projects, 4 scientific projects, and 5 defense projects. (RWR)

UK PubMed Central (United Kingdom)

Targeted genome capture combined with next-generation sequencing was used to analyze 2.9 Mb of the DFNB79 interval on chromosome 9q34.3, which includes 108 candidate genes. Genomic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The four mines supplying the Sasol-2 plant at Secunda, South Africa are approaching their full production potential of 29 million t/year. Current production is 27.7 million t/year of coal for gasification and steam raising. Three mining methods are employed: bord and pillar, longwall and continuous mining. Details are given of the mining operations and machinery. A 43 km overland conveyor transports the coal to the Sasol plant stockpile.

Wastenet

...Resort and Convention Center, National Harbor, Maryland, USA September 18-20, 2011 XX HELSINKI DRUG RESEARCH CONGRESS Helsinki, Finland October 23-27, 2011 2011 AAPS Annual Meeting and Exposition Washington Convention Center Washington, DC June 26-29 2012 10th International Symposium on Pharmaceutical Sciences Ankara, Turkey Printer-friendly version Home | Elsevier ...

Science.gov (United States)

His talk was based on the suggestion that life on Earh has been a long but accelerating ..... a New Class of Submarine Hydrothermal System"; April 29, 2002 , ..... of media personnel, including radio, television, newspapers, and magazines. ...... "The Birth of Stars and Planets" (Denver Museum of Nature and Science ...

UK PubMed Central (United Kingdom)

The use of tick vaccines in mammalian hosts has been shown to be the most promising alternative tick control method to current use of acaricides, which suffers from a number of limitations. However,...Full Text Available

International Nuclear Information System (INIS)

Ksub(#beta#)/Ksub(#alpha#) X-ray intensity ratios have been measured for various elements between Z = 29 and Z = 79 for incident proton energies of 23.6, 32.1 and 43.6 MeV. The results yield no evidence for a variation in ratio with particle energy. (orig.).

International Nuclear Information System (INIS)

Previous experiments had indicated a slight genotoxic potential both in rat and in human colon cells of a sample of 2-dodecylcyclobutanone, a compound formed by irradiation of food containing palmitic acid in its triglycerides. Up to date, there is no evidence that 2-alkylcyclobutanones occur in non-irradiated foodstuffs, consequently it is prudent to test several members of the class of 2-alkylcyclobutanones which are produced by treatment of fat-containing food with ionising radiation. In this work, 2-tetradecylcyclobutanone (derived from stearic acid) has been tested for its cytotoxic and genotoxic potential. Human colon tumor cell lines, i.e. HT 29 and HT 29 clone 19A, were employed as models for in vitro experiments for cytotoxicity and genotoxicity tests. Cytotoxicity was measured by tetrazolium salt reduction assays (MTT and WST-1) and genotoxicity by determining DNA damage using the Comet Assay. Neither cytotoxic nor genotoxic effects ...

Energy Technology Data Exchange (ETDEWEB)

This environmental review of right-of-way clearing for transmission projects has been undertaken by the Environmental Analysis Branch for the Division of Land Resources in BPA's Office of Engineering and Construction. It is intended to review the present practices and results of selective clearing, and to make recommendations toward improvements in environmental practices and procedures in mitigation development for impacts associated with right-of-way clearing. 29 figs.

International Nuclear Information System (INIS)

Here, we consider a recent paper concerned with magnetic braking by induced currents (Ireson and Twidle 2008 Eur. J. Phys. 29 745-51). Our objective is to elucidate why measurement of speed in which a magnet is dropped through a non-ferromagnetic conductive tube depends on its geometry in a non-monotonic way, which was not clearly explained by the authors. (letters and comments)

Energy Technology Data Exchange (ETDEWEB)

This study had two objectives: (1) To enhance the fundamental understanding of observed differences in the short contact time, donor solvent liquefaction of bituminous and subbituminous coals. (2) To determine if physical refining of subbituminous coals could be used to give a better feedstock for the first stage of two-stage liquefaction processes. Liquefaction studies using microautoclaves were carried out. Results are discussed. 11 refs., 25 figs., 29 tabs.

Science.gov (United States)

... 6.29;Temperate Pinus forest: 5.43;Temperate deciduous broad-leaved forest: 5.41;Boreal Larix deciduous forest: 4.63;Temperate evergreen sclerophyllous broad-leaved forest: 4.23Tropical deciduous broad-leav...

Energy Technology Data Exchange (ETDEWEB)

Adsorpt1on of CH[sub 4] and coadsorption of CH[sub 4] and CO on differently treated magnesium oxide have been studied by FT-IR spectroscopy at 173-273 K. Five IR bands at 3008, 3000, 2900, 2890, and approximately 1306 cm[sup [minus]1] were observed when well-outgassed MgO was exposed to CH[sub 4] at 173 K. The bands at 3008 and 3000 cm[sup [minus]1] are assigned to a degenerate stretch vibration of CH[sub 4], and those at 2900 and 2890 cm[sup [minus]1] originate from an infrared-forbidden mode at 2917 cm[sup [minus]1] of free CH[sub 4]. These bands became noticeably stronger with the outgassing temperature of MgO but could be sufficiently reduced as MgO was pretreated in air or under water vapor. Adsorbed CO on MgO gives two IR bands at 2161 and 2155 cm[sup [minus]1] which exhibit a parallel variation with those bands of adsorbed CH[sub 4] with the different pretreatments of MgO. Coadsorption of CH[sub 4] and CO indicated that adsorbed CO can deplete part of the ...

International Nuclear Information System (INIS)

Technique, allowing to investigate straggling zone (full braking) from high-energy charged particles in detail, is described. Experimental results on investigation of efective structure, created in polycrystalline molybdenum (99.97%) within 29 MeV alpha-particles straggling zone for fluences from 3.8x10"1"9 up to 3.7x10"2"1 #alpha#/m"2 by methods of microhardness (H_#mu#, X-ray structural analysis (#DELTA#a/a) and transparent electron microscopy (TEM), are presented. It is determined, that for doses from 3.8x10"2"0 #alpha#/m"2 and higher, at #approx#6 MeV energy, molybdenum ''softening'' is observed, H_#mu# curve within straggling zone is well described by alloyage calculated profile. #DELTA#a/a measurements within straggling zone are well described by damage profile. TEM-investigations have shown the developed defective structure even within molybdenum ''softening'' range.

Energy Technology Data Exchange (ETDEWEB)

To assess the potential of CT in evaluating the histological severity of acute appendicitis in comparison with surgical and pathological findings. The CT images of 75 patients with surgically proven appendicitis, including 10 cases of catarrhal, 34 of phlegmonous, and 31 of gangrenous appendicitis, were retrospectively analyzed for the following five CT findings: hazy periappendiceal densities, enlarged appendix, increased enhancement of the appendiceal wall, increased enhancement of the periappendiceal intestinal wall, and deficiency of the appendiceal wall. By comparing all the CT findings and the pathological severity of appendicitis (catarrhal, phlegmonous, and gangrenous), the prevalence of the five CT findings was calculated for each pathological category. Abnormal CT findings were noted in only one case of catarrhal appendicitis. Increased enhancement of the appendiceal wall was observed in all 29 cases of phlegmonous appendicitis (100%), but in only 66.7% ...

Science.gov (United States)

The dealumination of mordenite by acidification (HCl, HNO/sub 3/) and by SiCl/sub 4/ and steaming treatments is followed by high-resolution magic-angle-spinning solid-state /sup 29/Si and /sup 27/Al NMR spectroscopy. The combined use of these techniques leads to the determination of the silicon-aluminum ordering. It is demonstrated that aluminum atoms preferentially occupy tetrahedral positions in the four-membered rings of the mordenite structure. In addition, a mechanism of dealumination can be inferred, consisting in removing the aluminum atoms two by two from the four-membered rings. It is also possible to compute the number of SiOH groups left in the unit cell after the progressive removal of aluminum atoms: four groups per extracted Al atom are generated in the beginning of dealumination and this number gradually decreases to two, suggesting that a structural reorganization must necessarily occur for substantial dealumination. These silanol groups are also ...

Energy Technology Data Exchange (ETDEWEB)

The author describes the history of the Soviet Unions nuclear weapons testing in Siberia from the first bomb on 29th August 1949 until the test-ban treaty of 1963. The effects of the weapons testing on the local population is only now becoming widely known. Levels of cancers and cataracts are significantly higher than in uneffected populations, and there are also high levels of some lung, bone, skin and digestive conditions. Perhaps the most important information relates to cataracts, previously thought to be caused by single large bursts of radiation. Regulatory authorities worldwide will need to tighten the safety limits for eye radiation exposure to these findings. (U.K.).

Science.gov (United States)

This article presents the text of a lecture delivered by American Educational Research Association President Carol D. Lee at the 29th Annual Charles H. Thompson Lecture-Colloquium Series which was held on November 5, 2008. In her lecture, Lee discussed several points of similarities between W. E. B. Du Bois and President Barack Obama. These similarities in background, education, and in their ideas on politics and power are historically connected with implications for educating Black people though race consciousness.

Energy Technology Data Exchange (ETDEWEB)

This document contains the Proceedings of the Eleventh Thematic Conference Geologic Remote Sensing (Volume II). The conference was held February 27-29, 1996 in Las Vegas, Nevada, USA. Presentations included in this volume address the following topics: Geologic Remote Sensing and aerial surveying as applied toward mineral exploration, monitoring of geothermal resources, petroleum exploration, the environmental effects of mining, environment and hydrology, detection of geohazards, and the GIS system and data integration. Some information regarding the use of color imagery in remote sensing is also included.

Energy Technology Data Exchange (ETDEWEB)

The conceptual design, parametric analysis, cost and performance analysis, and commercial assessment of a 100-MWe line-focus solar central receiver power plant are reported. This volume contains the appendices: (a) methods of determination of molten salt heat-transfer coefficients and tube-wall temperatures, (b) inputs for STEAEC programs, (c) description of system analysis computer program, (d) receiver analysis program, and (e) heliostat production plan and design methodology. (WHK)

Energy Technology Data Exchange (ETDEWEB)

The major distributor and retailer of electrical power to Auckland, New Zealand, is Mercury Energy Limited. Following the sequential failure of the four 110kV underground cables, two gas-filled and two oil-filled, which supply the central business district, power was interrupted for 29 days from the 20th February 1998. A government inquiry was instituted, to examine what happened, why, and what lessons could be drawn for the future. Inadequacies in Mercury Energy`s cable maintenance and operating procedures were identified. The findings of the inquiry and its recommendations are reported. (UK)

Energy Technology Data Exchange (ETDEWEB)

We report on multijunction GaInP/GaAs photovoltaic cells with total-area efficiencies of 29.5% at one-sun concentration and air mass (AM) 1.5 global and 25.7% one-sun, AM0. These values represent the highest efficiencies achieved by any solar cell under these illumination conditions. Three key areas in this technology are identified and discussed: the grid design, front surface passivation of the top cell, and bottom surface passivation of both cells. Aspects of cell design related to its operation under different solar spectra and under concentration are also discussed.

Energy Technology Data Exchange (ETDEWEB)

The Balandin type volcano plots have been considered for the main criterion both in catalysis and electrocatalysis to estimate their fundamental properties and optimal activity: ({alpha}) The ones, when some physical feature or catalytic activity itself is plotted usually along transition series, and ({beta}) The others, when catalytic activity arises as a function of some energetic property, the most usually of the adsorption enthalpy of intermediates bonding upon the substrate in the rate determining step (rds). 29 refs.

Energy Technology Data Exchange (ETDEWEB)

Numerical analysis of solar dish modified cavity receiver with Cone, CPC and Trumpet reflectors is presented. Three-dimensional modeling is carried out to estimate the convective and radiative heat loss from the receiver for different angles of inclination and operating temperatures. Incorporating reflectors in the modified cavity receiver for second stage concentration, the natural convection heat losses are reduced by 29.23, 19.81 and 19.16%, respectively. The receiver with the trumpet reflector has shown better performance as compared to other configurations. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The present study was aimed to investigate antimicrobial potential of Glycyrrhiza glabra roots. Antimycobacterial activity of Glycyrrhiza glabra was found at 500mg/mL concentration. Bioactivity guided phytochemical analysis identified glabridin as potentially active against both Mycobacterium tuberculosis H37Ra and H37Rv strains at 29.16mg/mL concentration. It exhibited antimicrobial activity against both Gram-positive and Gram-negative bacteria. Our results indicate potential use of licorice as antitubercular agent through systemic experiments and sophisticated anti-TB assay.

Energy Technology Data Exchange (ETDEWEB)

The autoradiographic appearance of the gastric mucosa, 5 hours after administration of indomethacin, was investigated in 29 adult rats. Indomethacin induced superficial gastric erosions. Autoradiography demonstrated the presence of viable gastric cells (as deduced by their ability to incorporate 3H-cytidin, an RNA precursor) not only in the mucosa without erosions, but also in the mucosa underneath the superficial erosions. The results indicate that indomethacin induced gastric erosions are not the superficial expression of a necrotic process taking place in the full thickness of the gastric mucosa at a particular site. A lumen-borne mechanism appears to be responsible for the formation of erosive areas in the mucosa.

International Nuclear Information System (INIS)

The HT-28 and 29 irradiation capsules are part of a cooperative agreement between GA and ORNL designed to evaluate irradiation performance of unbonded BISO and TRISO coated ThO_2 fertile fuel particles. The capsules will contain a total of 44 different positions uniformly divided between each capsule. The positions in HT-29 are designated for operation at 900"0C over a fast fluence increment between 5.4 to 10.7 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/. Positions in HT-28 are divided into two sections: 11 positions at 1250"0C to receive a fast fluence exposure between 7.8 and 8.6 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/ and 11 positions at 900"0C designed for a 4.3 to 6.9 x 10"2"1 n/cm"2 (E > 0.18 MeV)/sub HFIR/ fast fluence exposure. Both capsuls are to serve as an evaluation test to characterize the performance of BISO OPyC coatings deposited from mixed-gas (acetylene-propylene). The OPyC variables tested will be density, coating ...

International Nuclear Information System (INIS)

The effect of X-irradiation on production of MUC1 was studied with human colon carcinoma HT-29 cells. As evaluated by immunocytochemical staining, the percentages or MUC1-positive cells in cells at 4 days after 6 Gy irradiation and in unirradiated control cells were 52#+-#3.5% (n=6) and 26#+-#2.8% (n=6), respectively. Flow-cytometric analysis of living cells showed that MUC1 began to rise from day 1, reaching a plateau by day 4 after 6 Gy irradiation. Western blot analysis with monoclonal antibody MY.1E12 against glycosylated MUC1 (mature form) showed dose-dependent increases of two bands (500 and 390 kDa) corresponding to two polymorphic MUC1 alleles. Premature forms of MUC1 (350 and 240 kDa) were detectable with monoclonal antibody HMFG-2 only in irradiated cells, suggesting that new core protein synthesis had been induced. The transcriptional activity of the MUC1 gene was analyzed in terms of transient expression of MUC1-CAT reporter plasmids containing ...

International Nuclear Information System (INIS)

Norway is a member of Annex 29, 'Ground-Source Heat Pump Systems Overcoming Technical and Market Barriers' (2004-2006), organized under the umbrella of the International Energy Agency (IEA) and the IEA Heat Pump Programme (HPP). The 7 participating countries are Austria (Operating Agent), Canada, Japan, Norway, Spain, Sweden and the USA. The Norwegian participation is financed by ENOVA SF, and SINTEF Energy Research is responsible for planning and carrying out the Norwegian activities. This report provides a status for ground-source heat pump (GSHP) systems in Norway with regard to state-of-the-art technology, installation examples, geological data, costs and market opportunities. A Norwegian Internet home page for ground-source heat pump systems (www.energy.sintef.no/prosjekt/Annex29) is also presented. GSHP systems in Norway are classified as direct systems (groundwater and soil/ground) and indirect closed-loop systems (vertical-rock and ...

International Nuclear Information System (INIS)

Under certain growth conditions, the human colon adenocarcinoma cell line HT-29 exhibits intestinal enterocyte-like properties. The differentiated cells possess a brush border with the enzyme markers (aminopeptidase and sucrase) normally associated with the intestine. To aid in the characterization of the transport properties of these cells, the uptake of a non-metabolizable amino acid analog, "1"4C-#alpha#-methylaminoisobutyric acid (MeAIB) as examined in the HT-29-Al subclone which possesses a brush border. The cells exhibited a time-dependent uptake of MeAIB which was concentrative and sodium-dependent. The pH optimum for uptake was about 7.8. Uptake was inhibited by low temperature, 1 mM ouabain, or 0.5 mM dinitrophenol. A 1 hr-preincubation of the cells in an isotonic KCl solution resulted in a decreased uptake rate, suggesting that a negative membrane potential is important for MeAIB uptake. The rate of 0.5 mM MeABIB uptake was inhibited ...

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples are dissolved in 6 M ...

Energy Technology Data Exchange (ETDEWEB)

Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal surfaces for the ...

Energy Technology Data Exchange (ETDEWEB)

Theoretical investigations on the phase change materials (PCMs) used as the heat storage media for box-type solar cookers have been conducted in this study. The selected PCMs are magnesium nitrate hexahydrate, stearic acid, acetamide, acetanilide and erythritol. For a two-dimensional simulation model based on the enthalpy approach, calculations have been made for the melt fraction with conduction only. Different materials such as glass, stainless steel, tin, aluminum mixed, aluminum and copper are used as the heat exchanger container materials in the numerical calculations. The large value of thermal conductivity of heat exchanger container material did not make a significant contribution on the melt fraction except for at very low thermal conductivities. Based on the theoretical results, stearic acid and acetamide are found to be good compatibility with latent heat storage system. It is also found that the initial temperature of PCM does not have very important ...

Science.gov (United States)

As with mammalian enzymes, green crab (Scylla serrata) alkaline phosphatase can be activated by Mg2+ through a time-dependent course. The activation is mainly a Vmax effect. Tsou's method was used to study the kinetic course of activation. The results show that the enzyme was activated by a complexing scheme that had not been previously identified: the enzyme first reversibly and quickly binds Mg2+ and then undergoes a slow reversible course to activation, with a relatively high activation energy (78 +/- 4 kJ/mol) and a slow conformational change. The activation reaction is a single molecule reaction, and the apparent activation rate constant is independent of Mg2+ concentration if the concentration is sufficiently high. The microscopic rate constants of activation and the association constant were determined from the measurements. The proposed scheme may also be applied to the Mg2+ activation mechanism for mammalian enzyme, to explain why the activation rate is time-dependent and not ...

Science.gov (United States)

Appendices to this summary consist of twelve individual status reports that will be available through the National Technical Information Service (NTIS) in the United States and of course limited copies will be available through NATO. The twelve report titles which are appendices to the summary are: (A) Status Report on the Limestone/Sludge Flue Gas Desulfurization Process; (B) Status Report on the Lime/Sludge Flue Gas Desulfurization Process; (C) Status Report on the Double Alkali/Sludge Flue Gas Desulfurization Process; (D) Status Report on the Sea Water Scrubbing Flue Gas Desulfurization Process; (E) Status Report on the Limestone/Gypsum Flue Gas Desulfurization Process; (F) Status Report on the Lime/Gypsum Flue Gas Desulfurization Process; (G) Status Report on the Double Alkali/Gypsum Flue Gas Desulfurization Process; (H) Status Report on Flue Gas Desulfurization by Scrubbing with Dilute Sulfuric Acid; (I) Status Report on the Magnesium Oxide Flue Gas ...

Energy Technology Data Exchange (ETDEWEB)

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride <0.05 M containing 30% ethylene glycol solution, they are more corrosive than the blank (30% ethylene glycol-70% water). However, at concentrations <0.05 for chloride or >0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy ...

British Library Electronic Table of Contents (United Kingdom)

The effects of anthropogenic (nitrogen fertilization) and natural [soil texture, pH content of humus, ammonium nitrogen (N-NH4), and the available forms of phosphorus (P), potassium (K), magnesium (Mg)] factors on nitrate nitrogen (NO3-N) content and distribution were shown. The dependencies between these factors and the content of NO3-N in soil were estimated in three soil layers: 0-30 cm; 31-60 cm; 61-90 cm. The research was carried out in 2004-2006, and the soil samples were taken from 411 places throughout eastern Poland in two seasons: spring and autumn. The concentration of NO3-N significantly depended on the year of investigation, season of the year, and depth of sampling. Distribution of NO3-N in the soil profile indicates possibility of NO3 leaching during winter and early spring....

Energy Technology Data Exchange (ETDEWEB)

The cost of transporting biogas digestate can be decreased by reducing its water content. However, the digestate emits volatile compounds during drying. This study investigated the drying behaviour and the change of digestate composition. Drying took place in a hybrid solar/waste-heat dryer that used solar energy as well as waste heat from a combined heat and power unit (CHP) and the exhaust air of a microturbine. The experiment involved the use of 60 t of liquid digestate. Climatic conditions were measured inside and outside the drying hall. Dry matter (DM) and organic dry matter (ODM) were also measured on a daily basis. In addition, the energy consumption of waste and solar heat were recorded and related to the quantity of dried feedstock. The total nitrogen, ammonium, phosphate, potassium oxide, magnesium oxide and calcium oxide in the digestate were subjected to chemical analysis before and after the drying process. Losses of nitrogen were calculated. Specific ...

International Nuclear Information System (INIS)

The difference of NH_4"+-N/NO_3"--N nutrition between hybrid and conventional rice varieties at the late growth stage was studied by using "1"5N-tracer technique. The results showed that the nitrate fertilizer utilization efficiency by the hybrid rice after anthesis was 7.8% higher than that by the ordinary rice variety, and the nitrate fertilizer recovery fraction by the former was 13.2% greater than that by the latter. The varietal difference in NO_3"--N uptake and utilization was almost twice as that in NH_4"+-N. It was also showed that "1"5N distribution in ear of the hybrid rice was about 20% greater than that of the conventional variety, but there were no obvious differences between NO_3"--N and NH_4"+-N. However, "1"5N distribution in the lower node leaves and root was found to be significant higher with NO_3"--N than that with NH_4"+-N in both rice varieties, particularly in the hybrid rice. Compared with NH_4"+-N, NO_3"--N top-dressing before anthesis was observed to have much ...

Science.gov (United States)

This report presents the operating results for Run 243 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary objective was to demonstrate the effect of a dissolver on the ITSL product slate, especially on the net C/sub 1/-C/sub 5/ gas production and hydrogen consumption. Run 243 began on 3 February 1983 and continued through 28 June 1983. During this period, 349.8 tons of coal was fed in 2947 hours of operation. Thirteen special product workup material balances were defined, and the results are presented herein. 29 figures, 19 tables.

Wastenet

... 300715+Ceramic+Engineering+and+Science+Proceedings 2122%28Series+Code%29+Ceramic+Engineering+and+Science+Proceedings Wiley::Ceramic Engineering and Science Proceedings WILEY KNOWLEDGE FOR ...CART | MY ACCOUNT | CONTACT US | HELP Home / Engineering & Materials Science / Materials Science / Ceramic Engineering and Science Proceedings Related Subjects Soft Matter Organic Electronics Structural ...Materials, Ceramics Structural Materials, Composites Structural Materials or Construction Materials Corrosion Electronics Materials Related Series Ceramic Transactions Series Wiley Series in Materials for ...Electronic and Optoelectric Applications Ceramic Engineering and Science Proceedings (CESP) contain proceedings from three American Ceramic Society (ACerS) meetings: ...

British Library Electronic Table of Contents (United Kingdom)

Introduction The progressive growth of malignancies is accompanied by a decline in the immune response through mechanisms which are poorly understood. Apoptosis and induction of inflammation by tumor released cytokines as tumor escape mechanisms have been proposed to play an important role in colorectal carcinogenesis. Methods Expression of Tumor necrosis factor-alpha (TNF-?) was analyzed in colorectal cancer specimen and the cancer cell line HT-29 by immunohistochemistry and RT-PCR. TNF-? expression on protein and mRNA level were correlated with clinical characteristics and impact on survival. TNFR-1 was co-labelled with TNF-? and CD8+ cytotoxic T cells in immunofluorescence double staining experiments. Results: 94% (n?=?98/104) of the patients with CRC expressed TNF-?. High TNF-? express...

Energy Technology Data Exchange (ETDEWEB)

Electrical resistivity of Nd{sub 7}Ni{sub 3} shows anomalies at the Neel temperature T{sub N} = 29 K and the Curie temperature T{sub C} = 14 K but does not show any change at the spin reorientation temperature T{sub R} = 8.7 K. The thermoelectric power has also bro[ humps around 250 and 50 K as well as a sharp break at T{sub N} and a minimum at 10 K. The corresponding Hall coefficient shows anomalies at T{sub N}, T{sub C} and T{sub R}, following the Curie-Weiss-law-like behavior above T{sub N}. (orig.) 7 refs.

International Nuclear Information System (INIS)

Starting from commercial 4-chloro-3-nitroaniline, through a 5 step synthesis, 3-azido-4-chlorophenylisothiocyanate was prepared and reacted with ["3H]-methylamine. The latter was obtained by three methods: (i) ["3H]-LiA1T_4 reduction of benzylcarbamate gave rise to ["3H]-methylamine (S.A.: > 70 Ci/mmol). (ii) Catalytic reduction of HCN with "3H_2 lead to ["3H]-CH_3NH_2 (S.A.: 0.7 Ci/mmol). (III) Schmidt rearrangement of ["3H]-sodium acetate gave ["3H]-CH_3NH_2 (S.A.: 29 Ci/mmol). (author).

Energy Technology Data Exchange (ETDEWEB)

Experiments have been carried out in water at 355 C to study transport of oxygen and hydrogen (as deuterium) in growing corrosion films. Composition of the films was also examined in 2.9 Mev and 3.9 Mev /alpha/-particle backscattering experiments. Corrosion occurs predominantly by oxygen diffusion through the film via grain boundary or similar short circuit diffusion paths, to form fresh oxide at the oxide metal interface. Increasing grain size within thick pre-breakaway films contributes to a decrease in diffusivity. The rate transition results from the generation of new diffusion pathways in previously protective oxide. Unexpectedly high concentrations of deuterium were observed. 26 refs.

British Library Electronic Table of Contents (United Kingdom)

Summary: The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR res...

British Library Electronic Table of Contents (United Kingdom)

In order to investigate the potential role of arctic geese in the epidemiology, the spatial and temporal spread of selected avian diseases, in autumn 2002, a virological and serological survey designed as capture-mark-resighting study was conducted in one of the most important coastal resting sites for migratory waterfowl in Germany. Oropharyngeal, cloacal swabs and blood samples were collected from a total of 147 birds comprising of three different arctic geese species including White-fronted Goose (Anser albifrons), Tundra Bean Goose (Anser fabalis rossicus), Pink-footed Goose (Anser brachyrhynchus) as well as from 29 non-migratory Canada Geese (Branta canadensis). Altogether, six adeno-like viruses (ALV; 95% CI, 1.74?9.92%) and two avian paramyxoviruses (APMV-4; 95% CI, 0.19?5.53%) were...

British Library Electronic Table of Contents (United Kingdom)

Abstract The distribution and abundance of native ungulates were measured on commercially managed, semi arid rangeland in central Kenya over a 3 year period that encompassed severe drought and above average rainfall. Native ungulate biomass density averaged 5282 kg km 2 over the study and was dominated by elephant (Loxodonta africana), impala (Aepyceros melampus) and dik dik (Madoqua kirkii). Biomass density of domestic cattle (Bos taurus) averaged 2280 kg km 2 during the study. Responses of native ungulates to severe drought were variable. Impala densities were similar to or greater than densities for similar habitat in protected areas, and varied from 12 to 16 km 2 during and following the drought to 24 29 km 2 following above average rainfall. Dik dik densities were also greater than de...

Energy Technology Data Exchange (ETDEWEB)

The first meeting on e{gamma}/{gamma}{gamma} colliders was held on September 28 and 29, 1993, at the National Laboratory for High Energy Physics. After general remarks were delivered, lectures were given on QED in intense laser field, photon linear collider, laser focusing, luminosity distribution in the e{gamma}/{gamma}{gamma} colliders, QCD correction for {gamma}{gamma}{yields}H, radiation correction for e{gamma}/{nu}W process, SUSY particle production at the e{gamma} and {gamma} gamma colliders, formation of e{sup *} in e{gamma} collision, and general remarks on the theory. Discussion was carried out on `Where are we going from here?` In this book, the gists of the lectures are collected. (K.I.).

British Library Electronic Table of Contents (United Kingdom)

Introduction Postoperative alopecia is a relatively rare event, and therefore both patients and surgeons are puzzled once it develops even though it is said to improve spontaneously with time in most cases. We report a parieto-occipital pressure-induced alopecia firstly developed in a patient who had undergone repeated surgery for 10?years after a traffic accident. Case report A 29-year-old male underwent segmental osteotomy at the upper and lower frontal edentulous areas for distraction osteogenesis. Throughout the operation, he was in the supine position with the hair covered with a paper cap and the head on a plastic vinyl chloride-covered soft foam horseshoe-shaped urethane sponge placed on the horseshoe-shaped headrest. About 2?weeks after the surgery, two patches of parieto-occipital...

Science.gov (United States)

In terms of the reduced potential energy barrier ? = ?uTS/kT, the rate coefficients for chemical reactions are usually expressed as proportional to e-?. The coupling between vibrational modes of the medium to the reaction coordinate leads to a proportionality of the regularized gamma function of Euler Q(a,?) = ?(a,?)/?(a), with a being the number of modes coupled to the reaction coordinate. In this work, the experimental rate coefficients at various temperatures for several chemical reactions were fitted to the theoretical expression in terms of Q(a,?) to determine the extent of its validity and generality. The new expression affords lower deviations from the experimental points in 29 cases out of 38 and it accounts for the curvature in the logarithmic plots of rate coefficients versus inverse temperature. In the absence of tunneling, conventional theories predict the curvature of these plots to be identically zero.

Energy Technology Data Exchange (ETDEWEB)

The ORR operated at an average power level of 29.7 MW for 85.3% of the time during this period. The reactor was shut down on fifteen occasions, nine of which were unscheduled. Reactor downtime needed for refueling and checks was normal. The reactor remained available for operation 88.3% of the time. Special tests completed during the quarter included: (1) transfer of LEU fuel elements CLE-202 and NLE-201 from core positions B-9 and B-2 to core positions C-5 and C-6 for continued operation; and (2) calculation of maximum heat flux in LEU elements CLE-201 and NLE-202 in core positions A-2 and A-8. In-service inspections included inspections of ORR decay tank, primary heat exchanger No. 4, and the 24-in. strainer.

British Library Electronic Table of Contents (United Kingdom)

Precocious puberty is a significant child health problem, especially in girls, because 95% of cases are idiopathic. Our earlier studies demonstrated that low-dose levels of manganese (Mn) caused precocious puberty via stimulating the secretion of luteinizing hormone-releasing hormone (LHRH). Because glial-neuronal communications are important for the activation of LHRH secretion at puberty, we investigated the effects of prepubertal Mn exposure on specific glial-derived puberty-related genes known to affect neuronal LHRH release. Animals were supplemented with MnCl2 (10 mg/kg) or saline by gastric gavage from day 12 until day 22 or day 29, then decapitated, and brains removed. The site of LHRH release is the medial basal hypothalamus (MBH), and tissues from this area were analyzed by real-...

Science.gov (United States)

{sup 1}H, {sup 13}C, {sup 27}Al, and {sup 29}Si magic-angle-spinning (MAS) NMR was used to elucidate the nature of the catalytic activity of zeolite H-ZSM-5. {sup 1}H MAS NMR of sealed samples after mild hydrothermal dealumination shows that the enhanced activity for n-hexane cracking is not due to an enhanced Bronstead acidity. The concentrations of the various OH groups and aluminous species suggest that the reason for the enhanced catalytic activity is the interaction of the n-hexane molecule with a bridging hydroxyl group and with extra-framework aluminium species, which give rise to the enhanced activity, cannot be easily removed from their positions, and are therefore immobilized by the zeolitic framework.

Energy Technology Data Exchange (ETDEWEB)

The Seabed Disposal Project (SDP) was evaluating the technical feasibility of high-level nuclear waste disposal in deep ocean sediments. Working standards were needed for risk assessments, evaluation of alternative designs, sensitivity studies, and conceptual design guidelines. This report completes a three part program to develop radiological standards for the feasibility phase of the SDP. The characteristics of subseabed disposal and how they affect the selection of standards are discussed. General radiological protection standards are reviewed, along with some new methods, and a systematic approach to developing standards is presented. The selected interim radiological standards for the SDP and the reasons for their selection are given. These standards have no legal or regulatory status and will be replaced or modified by regulatory agencies if subseabed disposal is implemented. 56 refs., 29 figs., 15 tabs.

Science.gov (United States)

It is shown that level-density expressions cannot adequately represent or substitute for level structure information when making calculations of the Hauser-Feshbach type for cross sections or isomer-ratios for nuclei in the first few MeV above their ground state. It is stated that such discrete level information should include both experimentally confirmed and theoretically predicted levels. The utility of discrete level information to optimize level density calculations, to compute isomer ratios, in deriving dipole strength functions, and in the analysis of primary gamma ray spectra is emphasized, especially for nuclei far from the line of stability. 29 refs., 12 figs., 6 tabs. (DWL)

British Library Electronic Table of Contents (United Kingdom)

The Iberian lynx is the most endangered felid in the world. Enteropathogens may threaten its survival, and therefore we analysed faecal samples from 66 different individuals (37 males and 29 females), the largest population representation studied to date. The samples were obtained from November 2005 to October 2008 in the two areas where the Iberian lynx survives: Sierra Morena and Donana (Andalusia, southern Spain). A total of 56.1% samples were parasitized with at least 6 species of helminths, including two cestodes (Hymenolepis spp. and Taenia spp.) and four Nematodes (Ancylostoma spp., Toxocara spp., Toxascaris leonina, and Capillaria sp.). In this work, the presence of Hymenolepis is reported for the first time in Lynx pardinus. The relevance of our findings is discussed focussed on t...

British Library Electronic Table of Contents (United Kingdom)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr2N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30-35wt%) Ni-Cr alloys and a ferritic high Cr (29wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effect...

Energy Technology Data Exchange (ETDEWEB)

A large detector with high redundancy is used to search for various types of anomalous particles in cosmic rays at sea level. The detector is sensitive to zenith angles between 45/sup 0/ and 90/sup 0/. Previously obtained limits on the fluxes of charge (1/3) and (2/3) particles are reduced to 2.9 x 10/sup -10/ and 2.6 x 10/sup -10/ cm/sup -2/sr /sup -1/ sec/sup -1/, respectively. The flux of ionizing tachyons is determined to be less than 2.4 x 10/sup -9/ cm/sup -2/ sr/sup -1/ sec/sup -1/. The massive-particle flux limit we obtain is inconsistent with previous claims of such particles assuming that these particles are isotropic in zenith angle.

Energy Technology Data Exchange (ETDEWEB)

Evidence is reported for a narrow structure near the J/{psi}{phi} threshold in exclusive B{sup +} {yields} J/{psi}{phi}K{sup +} decays produced in {bar p}p collisions at {radical}s = 1.96 TeV. A signal of 14 {+-} 5 events, with statistical significance in excess of 3.8 standard deviations, is observed in a data sample corresponding to an integrated luminosity of 2.7 fb{sup -1}, collected by the CDF II detector. The mass and natural width of the structure are measured to be 4143.0 {+-} 2.9(stat) {+-} 1.2(syst) MeV/c{sup 2} and 11.7{sub -5.0}{sup +8.3}(stat) {+-} 3.7(syst) MeV/c{sup 2}.

British Library Electronic Table of Contents (United Kingdom)

Ochratoxin A (OTA) was analyzed from 44 liquorice confectionery samples using immunoaffinity cleanup and liquid chromatography coupled with fluorescence detection. The presence of OTA was confirmed by methyl-ester derivatization. Liquorice confectionery samples were purchased from different retail outlets and supermarkets in Spain during 2007-2008, 16 of hard candies and 28 of soft candies. The incidence of OTA varied between 75% and 39% and mean ranged from 2.96 to 0.34mg/kg for hard and soft candies, respectively. Assuming a total mean value of 1.29mgOTA/kg sweet and a consumption of about 1.2g liquorice sweets per day, an OTA weekly uptake of 11ng was obtained, or, based on a total body weight of 30kg for a child consuming these sweets regularly, a weekly intake of 0.37ng/kg body weight...

British Library Electronic Table of Contents (United Kingdom)

Abstract This study investigated the effects of Maillard reaction products (MRPs) on in vitro starch hydrolysis, and in vivo blood glucose responses in mice. Four MRPs of various dextrose equivalents were prepared by heating a mixture of hydrolyzed rice starch and glycine at 200C for 4-min. The starch hydrolysis rates of gelatinized rice starch (GRS) decreased as the browning reaction of added MRPs increased. The hydrolysis kinetic constants of the GRS with 5% MRPs were relatively lower than that of GRS without MRPs. Blood glucose responses showed similar tendencies to the in vitro starch hydrolysis results. The activity of digestive enzymes was inhibited by the MRPs. The relative crystallinity of all MRPs (29.9-60.1%) appeared to have higher values than GRS (15.1%). The samples heated to ...

Wastenet

...3 MtC, with 78% of these emissions from integrated steel making (26.9 MtC) and the rest (22%)...6 MtC, with 71% of these emissions from integrated steel making (21.9 MtC) and the rest (29%)...1 million ton of carbon (MtC) in 1994 (3.9 MtC from integrated steel making, and 2.2 MtC from secondary ...7 MtC in 2002 (3.7 MtC from integrated steel making, and 2.0 MtC from secondary steel making), corresponding ...

British Library Electronic Table of Contents (United Kingdom)

Nonfunctioning pancreatic endocrine tumors (PETs) are rare and generally asymptomatic. A 68-year-old woman who had refused treatment for a pancreatic mass, revealed by ultrasonography to be 55 mm in diameter, was referred to us again 29 months later with jaundice. Investigations showed an 82-mm tumor in the head of pancreas, exposed from the papilla of Vater to the duodenal lumen. After biliary decompression and drainage, we performed pancreatoduodenectomy with resection of the portal vein and superior mesenteric vein, followed by reconstruction using a cylindrically customized autologous graft harvested from the right ovarian vein. The tumor was resected curatively. Microscopically, it consisted of trabecular and ribbon-like arrangement of neoplastic cells. Immunohistochemical staining wa...

Energy Technology Data Exchange (ETDEWEB)

A clone encoding a human D{sub 2} dopamine receptor was isolated from a pituitary cDNA library and sequenced. The deduced protein sequence is 96% identical with that of the cloned rat receptor with one major difference: the human receptor contains an additional 29 amino acids in its putative third cytoplasmic loop. Southern blotting demonstrated the presence of only one human D{sub 2} receptor gene. Two overlapping phage containing the gene were isolated and characterized. DNA sequence analysis of these clones showed that the coding sequence is interrupted by six introns and that the additional amino acids present in the human pituitary receptor are encoded by a single exon of 87 base pairs. The involvement of this sequence in alternative splicing and its biological significance are discussed.

Energy Technology Data Exchange (ETDEWEB)

Rye straw was completely hydroliquefied, using red mud or CoO-MoO{sub 3} as the catalyst. Red mud catalyst exhibited a satisfactory activity only in the presence of sulphur at {approx} 673 K. Depending on reaction conditions, different amounts of gaseous and liquid products were formed. Their product distributions were comparable to those obtained in hydroliquefaction of cellulose and lignin. All results could be described by a model which assumed that: pyrolysis precedes hydrogenation of pyrolysis products; CO and CO{sub 2} are products of pyrolysis reaction; and hydrogen is consumed mainly in hydrodeoxygenation reactions. Therefore, from a practical point of view, red mud, which is known as a coal liquefaction catalyst, can also be recommended as a cheap and powerful catalyst in the hydroliquefaction of biomass. 29 refs., 6 figs., 11 tabs.

British Library Electronic Table of Contents (United Kingdom)

Colorectal cancer is the second most common cause of cancer death in the world and about half of the patients with colorectal cancer require adjuvant therapy after surgical resection. Therefore, the eradication of cancer cells via chemotherapy constitutes a viable approach to treating patients with colorectal cancer. In this study, the effects of bufalin isolated from a traditional Chinese medicine were evaluated and characterized in HT-29 and Caco-2 human colon cancer cells. Contrary to its well-documented apoptosis-promoting activity in other cancer cells, bufalin did not cause caspase-dependent cell death in colon cancer cells, as indicated by the absence of significant early apoptosis as well as poly(ADP-ribose) polymerase and caspase-3 cleavage. Instead, bufalin activated an autophagy...

British Library Electronic Table of Contents (United Kingdom)

Goldstein SL, Mattoo TK, Morgenstern B, Martz K, Stablein D, Talley L. Anemia and growth status in pediatric patients receiving maintenance dialysis after a failed renal transplant course: An NAPRTCS report.Pediatr Transplantation 2006. Copyright 2006 Blackwell Munksgaard Abstract: We conducted a retrospective review of the North American Renal Transplant Cooperative Study (NAPRTCS) Registry transplant and dialysis arms to assess anemia and growth patterns in children who returned to dialysis after a failed renal transplant from January 1, 1992 to February 3, 2004. Of the 1807 potential study subjects, 1451 had transplant removal data (TxIn vs. TxOut) available for analysis. Four hundred and twenty-one of 1451 patients (29%) had a transplant nephrectomy at the time of entry into the NAPRTC...

British Library Electronic Table of Contents (United Kingdom)

The interscalenic block technique is widely used for ambulatory shoulder surgery despite a substantial number of failures and adverse effects. We prospectively evaluated satisfaction in 40 consecutive patients who underwent open Bankart repair under a single general anesthesic performed in an ambulatory care unit. The mean age of the patients was 23 years. There were 29 men and 11 women. Patients were evaluated postoperatively with a visual analog scale of pain (in the recovery room, at the time of discharge, and the day after and 1 week after surgery) via a home assessment questionnaire that included the following: effectiveness of oral pain medication, ability to perform activities of daily life, and overall satisfaction. One patient failed to be discharged because of a feeling of faintn...

International Nuclear Information System (INIS)

The 5-th International conference 'Nuclear and Radiation Physics' was held in Almaty (Kazakhstan) 26-29 September 2005. Besides basic problems of nuclear and solid state physics the conference paid considerable attention to applied topics important for industry and science in Kazakhstan; they include fuel and construction materials for nuclear power production, new technologies and materials for their production, materials for hydrogen power production, handling and utilization of radioactive waste, analytical methods for combating with illicit trafficking of nuclear and radioactive materials, technologies for reduction and assessment of environmental risk from radiation-hazardous materials and sites, production and application of isotopes, application of nuclear technologies in medicine and industry. On the conference more than 300 papers were presented by participants from 20 countries.

International Nuclear Information System (INIS)

By observing the diffusion of a heat pulse along a 10-cm column of normal liquid "3He with the aid of two vibrating wire thermometers, it has been possible to measure the heat capacity C and thermal conductivity K of the liquid in the temperature range from T /sub c/ to 10 mK and at pressures of 0.21, 4.39, 9.97, 20.01, and 29.32 bar. By using a Pt NMR thermometer, an LCMN thermometer, and a "3He melting curve thermometer calibrated using the melting curve given by Greywall in 1983, a temperature scale has been established and (1) it has been shown that this melting curve is consistent in the temperature range 5-22 mK with the Korringa law for the Pt thermometer with a Korringa constant of 29.8 +/- 0.2 sec mK, (2) departures have been observed from the Curie-Weiss law for LCMN at low temperatures, and (3) values of the superfluid transition temperature have been obtained that are about 4% lower than the Helsinki values. The measured heat ...

International Nuclear Information System (INIS)

"2"7Al and "2"9Si solid-state NMR spectra and X-ray diffraction (XRD) patterns were obtained for #alpha#-SiAlON powders prepared by combustion synthesis, according to which the phase transformation and structure evolution of #alpha#-SiAlON were studied. It was found that in #alpha#-SiAlON "2"9Si chemical shift values (-48 < #delta# _S_i < -47) were close to those in #beta#-Si_3N_4 and #alpha#-Si_3N_4, indicating that Si atoms kept SiN_4 coordination to a large extent in #alpha#-SiAlON despite the presence of O atoms. Dissimilarly, "2"7Al chemical shift values in #alpha#-SiAlON deviated clearly from that corresponding to AlN_4 coordination (#delta# _A_l #approx# 112) and occurred in a range from #delta# _A_l 95.5 to 99.9, which should be assigned to tetrahedral AlO _xN_4_-_x (0 #<=# x #<=# 4) coordination. The broadening effect of AlO _xN_4_-_x peaks was noticed, which was suggested to induced by slight dispersion of #alpha#-SiAlON ...

Energy Technology Data Exchange (ETDEWEB)

Potential maximum radiation dose rates over a 1,000-year time horizon were calculated for exposure to the decontaminated concrete removed from the 183-H Solar Evaporation Basins at the Hanford Site, Richland, Washington. The RESRAD computer code, Version 5.62, which implements the methodology described in the US Department of Energy`s manual for developing residual radioactive material guidelines, was used in this evaluation. Currently, the concrete is not being used. Four potential exposure scenarios were developed for the land area where the decontaminated concrete will be stored. In Scenario A industrial use of the land is assumed; in Scenario B recreational use of the land is assumed; in Scenario C residential use of the land is assumed; and in Scenario D (a plausible but unlikely land-use scenario), the presence of a subsistence farmer in the immediate vicinity of the land is assumed. For Scenarios A and B, water used for drinking is assumed to be surface water from the Columbia ...