International Nuclear Information System (INIS)
Specific objectives were to: (1) develop and refine a methodology that can be used to evaluate the feasibility of MAG-LEV trains; (2) apply this methodology to the state of Oklahoma. The methodology is based on an aggregate econometric demand model and mathematical programming. A city-pair network is constructed to evaluate alternative MAG-LEV routes between Oklahoma City and nine other cites in and out of the state of Oklahoma. Results obtained from the aggregate econometric demand model indicates that MAG-LEV trains would attract significant ridership along different types of origin-destination routes. All nine corridors exhibit induced demand for MAG-LEV trains as well as attracting riderships from other modes. Based on the results of both single and multiobjective LP models, fixed-capital-cost requirements and annual operating cost for each of the above corridors are estimated, ...
International Symposium on Magnetic Suspension Technology. Part 2
International Nuclear Information System (INIS)
In order to examine the state of technology of all areas of magnetic suspension and to review related recent developments in sensors and controls approaches, superconducting magnet technology, and design/implementation practices, a symposium was held. The proceedings are presented. The sessions covered the areas of bearings, sensors and controls, microgravity and vibration isolation, superconductivity, manufacturing applications, wind tunnel magnetic suspension systems, magnetically levitated trains (MAGLEV), space applications, and large gap magnetic suspension systems.
1991-08-19
A vision for Berlin and the Transrapid; Eine Vision fuer Berlin und den Transrapid
Energy Technology Data Exchange (ETDEWEB)
This paper demonstrates how maglev technology solves the classic problem of integrating two airports in a metropolitan area. So far, this has never been attempted because the mode of transportation that could handle this challenge effectively had not been invented yet. This also means that maglev technology is no longer 'the solution in search of a problem'. (orig.)
2005-07-01
Study of Japanese electrodynamic-suspension maglev systems
Energy Technology Data Exchange (ETDEWEB)
This report presents the results of a study of the Japanese MLU magnetic-levitation (maglev) system. The development of the MLU system is reviewed, and the dynamic circuit model then is introduced and applied to the figure-eight-shaped null-flux coil suspension system. Three different types of figure-eight-shaped null-flux suspension systems are discussed in detail: (1) the figure-eight-shaped null-flux coil suspension system without cross-connection; (2) the combined suspension and guidance system; and (3) the combined propulsion, levitation, and guidance system. The electrodynamic-suspension maglev systems developed in Japan seem to be very promising and could result in a commercial application in the near future.
1994-04-01
International Science & Technology Center (ISTC)
Development of Experimental Large-scale Technology and Creation of Technological Line of Rubomicine Production
Surface Decontamination by Solution
International Science & Technology Center (ISTC)
Development of Technology for Metal Surface Decontamination in Aqueous Solutions
Planning and Operation of Commercial Application Center
Energy Technology Data Exchange (ETDEWEB)
The objectives of this R and D project are as follows : First, transferring developed technologies to outside companies and operating technology market to vitalize technology transactions, Second, developing commercial application projects to transfer technologies for commercial purposes and to solve interface problems in commercial applications, Third, enhancing commercial utilizations of developed accelerator and beam utilization technologies, Finally. preparing infra-structures for the development of over 30 venture- businesses based on achieved technologies through the Proton Engineering Frontier Project.
2003-06-15
Instructional Materials Development Program
... Materials Development Program TECHNOLOGY EDUCATION INSTRUCTIONAL MATERIALS Elementary - High School ... of technology education materials through its Instructional Materials Development (IMD) program. The ...
Technology and Policy for Sustainable Development
The development of short-sea shipping will be fostered by the deployment of tracking and tracing systems,
Organizational structure and technology transfer
International Nuclear Information System (INIS)
... administrative procedures developing countries economic development nuclear
1982-11-01
Self-Propagating High-Temperature Synthesis Technologies
International Science & Technology Center (ISTC)
Development of SHS-technologies for SiC, Si3N4 and Ceramic Composites on Their Basis from Rocks
Human Systems Center Products and Progress.
... Page 43. Integrated Audio Technology Demonstrator The Integrated Audio Technology Dem- development for this application is successful. ...
1993-10-01
Considerations in the Design and Development of a Human ...
... appropriate. At press time, the laws governing the use of digital audio technology and the technology itself are rapidly changing. ...
1990-09-20
COMMUNICATION MEDIA AND EDUCATIONAL TECHNOLOGY AN - NASA Technical ...
adaptations of analog audio technology Recent developments in tape cassette technolocy have made Itpossible to provide up to ...
Training for New Manufacturing Technologies.
Examines the effects of computer-based manufacturing technologies on employment opportunities and job skills. Describes the establishment of the Industrial Technology Institute in Michigan to develop and utilize advanced manufacturing technologies, and the institute's relationship to the state's community colleges. Reviews lessons learned from interinstitutional cooperation. Highlights future challenges. (DMM)
1987-12-01
Geothermal Energy Research and Development Program; Project Summaries
Energy Technology Data Exchange (ETDEWEB)
This is an internal DOE Geothermal Program document. This document contains summaries of projects related to exploration technology, reservoir technology, drilling technology, conversion technology, materials, biochemical processes, and direct heat applications. [DJE-2005
1994-03-01
International Science & Technology Center (ISTC)
Research and Development of Resource-Saving Technology for Manufacturing of Titanium Semifinished Items from Chips
International Science & Technology Center (ISTC)
Development of the Technology to Obtain Pure Metal Scandium by Thermal Decomposition of Scandium Iodide
Energy Technology Data Exchange (ETDEWEB)
The paper discusses clean coal technology developments in India. 2 photos.
2011-01-15
Corrosion Protection of special steels and alloys
International Science & Technology Center (ISTC)
Development of the Corrosion Protection Technology for Special Steels and Alloys
Continuous Strategy Development for Effects-Based ...
... BAE Systems Advanced Information Technologies, Inc. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. ...
2006-02-01
International Science & Technology Center (ISTC)
Development of Technologies for Boron-10 Isotope Modified Boron-containing Materials Production and their Properties Investigation.
DEVELOPMENT OF A MANUFACTURING PROCESS AND ...
... This work was based upon previously successful development of combustible cartridge cases, at Illinois Institute of Technology Research Institute ...
1968-05-01
Safeguards and Security Technology Development Directory. FY 1993
Energy Technology Data Exchange (ETDEWEB)
The Safeguards and Security Technology Development Directory is published annually by the Office of Safeguards and Security (OSS) of the US Department of Energy (DOE), and is Intended to inform recipients of the full scope of the OSS R&D program. It is distributed for use by DOE headquarters personnel, DOE program offices, DOE field offices, DOE operating contractors, national laboratories, other federal agencies, and foreign governments. Chapters 1 through 7 of the Directory provide general information regarding the Technology Development Program, including the mission, program description, organizational roles and responsibilities, technology development lifecycle, requirements analysis, program formulation, the task selection process, technology development infrastructure, technology transfer ...
1993-06-01
Proceedings of the Vertical Axis Wind Turbine (VAWT) Design Technology Seminar for Industry
The objective of the program is to develop technology that results in economical, industry produced, and commercially marketable wind energy systems. The purpose of the VAWT Design Technology Seminar for Industry was to provide for the exchange of the current state of the art and predictions for future VAWT technology. Emphasis was placed on technology transfer on Sandia's technical developments and on defining the available analytic and design tools.
1980-08-01
Perspectives on energy storage wheels for space station application
Energy Technology Data Exchange (ETDEWEB)
Several of the issues of the workshop are addressed from the perspective of a potential Space Station developer and energy wheel user. Systems considerations are emphasized rather than component technology. The potential of energy storage wheel (ESW) concept is discussed. The current status of the technology base is described. Justification for advanced technology development is also discussed. The study concludes that energy storage in wheels is an attractive concept for immediate technology development and future Space Station application.
1984-11-01
NASA Project Inducted Into Space Technology Hall of
Apr 9, 2003 ... Adam Kissiah Jr., a retired KSC engineer, will be honored for his development of the digital hearing aid technology that led to the cochlear ...
An Advance in Superconducting Magnet Technology Opens the Door...
magnet research at several national laboratories through its Advanced Accelerator Technology Program. The HEP Conductor Development Program, a collaboration among national...
2011-08-20
R&D prioritization and resource management for technology selection
Energy Technology Data Exchange (ETDEWEB)
This paper presents a decision approach, and associated computer software tools, for prioritizing and selecting among technology development activities. The approach elicits and then summarizes technology development preferences from stakeholders, and then integrates preferences into a set of funding recommendations. By formalizing the technology review process, the decision approach builds consensus and clarifies the basis for final budget decisions. The software development was conducted jointly by Pacific Northwest Laboratory and Decisions Science Associates, Incorporated. The Underground Storage Tank Integrated Demonstration funded the task; however, the approach should also be valuable to the US Department of Energy Office of Technology Development, the Office of Waste Management, and the Office of Environmental ...
1994-03-01
SRS environmental technology development field test platform
Energy Technology Data Exchange (ETDEWEB)
A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper ...
1995-09-01
Planning of Medium- and Long-Term Strategy for the Safeguards Technology Development
International Nuclear Information System (INIS)
In Rep. of Korea, active safeguards technology development suitable to phase of a nuclear advanced country is necessary because of below reasons. First reasons are '6th ranked position in the nuclear energy generation all over the world', 'continuously increased outcomes in the various nuclear fields such as research or patent', 'strengthened intention of the new government for nuclear industries', and 'weakness of the R and D foundation related to the safeguards technology'. Second reasons are optimization necessity of the effectiveness and efficiency of safeguards according to enlargement of the SSAC (State Systems of Accounting for and Control) role. The reason of the enlargement of the SSAC is IAEA IS (Integrated Safeguards) application for Korea. Third reasons are necessity for the systematic national development plan considering the Korea R and D level and the degree of the difficulty of ...
2009-05-01
Sustaining integrated technology in undergraduate mathematics
British Library Electronic Table of Contents (United Kingdom)
The effective integration of technology into the teaching and learning of mathematics remains one of the critical challenges facing contemporary tertiary mathematics. This article reports on some significant findings of a wider study investigating the use of technology in undergraduate mathematics. It first discusses a taxonomy developed to describe and compare technology use within individual courses and departments that identifies a complex range of factors, summarized under six defining characteristics of an integrated technology mathematics curriculum (ITMC). An instrument for a simple comparison of technology use employing the elements of this taxonomy is provided. It then presents evidence gathered from an observational study of technology implementation at The University of Auckland...
2011-01-01
International Nuclear Information System (INIS)
The paper analyses the advantages and disadvantages of the second generation improved technologies and third generation technologies mainly developed in China in terms of safety and economy. The paper also discusses the maturity of the second generation improved technologies and the sophistication of the third generation technologies respectively. Meanwhile, the paper proposes that the advantage and disadvantage of second generation improved technologies and third generation technologies should be carefully taken into consideration and the relationship between the maturity and sophistication should be properly dealt with in the current stage. A two-step strategy shall be taken as a solution to solve the problem of insufficient capacity of nuclear power, trace and develop the third generation ...
2009-06-01
Studies in advanced coal research are presented. Included are the following: coal science programs; coal preparation and combustion kinetics; advanced technology in liquefaction, including direct and indirect liquefaction; alternative fuels; advanced combustion technology; flue gas cleanup; environmental coordination, technology transfer, and clean coal demonstration program. (CBS)
1987-11-01
Preliminary analysis of patent trends for sodium/sulfur battery technology
Energy Technology Data Exchange (ETDEWEB)
This document summarizes development trends in sodium/sulfur battery technology based on data from US patents. Purpose of the study was to use the activity, timing and ownership of 285 US patents to identify and describe broad patterns of change in sodium/sulfur battery technology. The analysis was conducted using newly developed statistical and computer graphic techniques for describing technology development trends from patent data. This analysis suggests that for some technologies trends in patent data provide useful information for public and private R and D planning.
1985-07-01
Agricultural R&D, technology and productivity
UK PubMed Central (United Kingdom)
The relationships between basic and applied agricultural R&D, developed and developing country R&D and between R&D, extension, technology and productivity growth are outlined....Full Text Available
2010-09-27
Untitled - NASA Technical Report Server (NTRS)
Directional audio technology for headphone applications is being developed. A laboratory demonstration model of a real-time digital ...
International Science & Technology Center (ISTC)
The Development of Basic Plasma-Chemical Technology for Manufacture of Low Cost Crystal Silicon for Solar Power Plants.
Improved Usability of Locomotion Devices Using Human ...
... increasing photorealism. Furthermore, developments in audio technology continue to increase the spatial awareness of users in VEs. ...
2009-03-01
Combustible Cartridge Cases, an Account of the Current ...
... ADA185428. Title : Combustible Cartridge Cases, an Account of the Current Technology and Proposals for Future Development. ...
1986-10-01
Advanced Thermal Management for Military Application
... management. 5.3 Decreased Emissions Changes in engine emission regulations are driving engine technology development. A ...
2004-12-01
Energy Technology Data Exchange (ETDEWEB)
The two primary objectives of the proposal were (1) to enhance science and technology infrastructure, faculty development, and curriculum by integrating technology throughout science education programs of study, and (2) to increase faculty and students` knowledge of and skills in modern technologies that are designed to enhance the effectiveness of teaching and learning through education, research and communications. These two primary objectives have been accomplished through: Installation and operation of a technology-ready classroom; Upgrading CIS 200 Introduction to Computers; Upgrading all science laboratory courses to include integration of science and technology through installation of computers; Faculty development through attendance at workshops, seminars, or conferences related to technology applicable to ...
1998-12-01
This document contains 142 papers on PT3 (Preparing Tomorrow's Teachers to use Technology) from the SITE (Society for Information Technology & Teacher Education) 2002 conference. Topics covered include: a technology in urban education summit; student professional development; meeting NCATE (National Council of Teachers of English) standards; faculty use of WebCT; preparing teachers for the digital age; technology in K-8 multicultural classrooms; using immersive 360 degree images; consortium building; student evaluation; technology fellows; incentives that facilitate institutional change; impact of a temporary grant; a consortium for outstanding achievement in teaching with technology; changes implemented after technology professional development sessions; Web-based modules for teaching ...
2002-03-01
Advanced Technological Education Program: 1999 Awards and Activities
... By developing and disseminating educational materials and curricula, supporting the preparation and ... education, such as curriculum or educational materials development, faculty or teacher preparation ...
Advanced PWR technology development -Development of advanced PWR system analysis technology-
Energy Technology Data Exchange (ETDEWEB)
The primary scope of this study is to establish the analysis technology for the advanced reactor designed on the basis of the passive and inherent safety concepts. This study is extended to the application of these technology to the safety analysis of the passive reactor. The study was performed for the small and medium sized reactor and the large sized reactor by focusing on the development of the analysis technology for the passive components. Among the identified concepts the once-through steam generator, the natural circulation of the integral reactor, heat pipe for containment cooling, and hydraulic valve were selected as the high priority items to be developed and the related studies are being performed for these items. For the large sized passive reactor, the study plans to extend the applicability of the best estimate computer code RELAP5/MOD3 which is widely used for the ...
1995-07-01
Energy Technology Data Exchange (ETDEWEB)
The paper reported the results of fiscal 1994 studies on solar energy in the New Sunshine Project. Relating to the technical development for the practical use of photovoltaic power systems, the development of manufacturing technologies for low-cost substrates and the development of element technology for manufacturing low-cost polycrystalline cells/modules were reported as the development of technology for thin substrate polycrystalline solar cells for practical use. As to the research on fabrication technology for thin film solar cells for practical use, reports were made on the research on low-cost fabrication technology for large-area modules and the technological development for qualitative improvement, etc. In respect to the ...
1994-12-01
An overview of PETC`s gas-to-liquids technology R&D Program
Energy Technology Data Exchange (ETDEWEB)
The overall goal of the Gas-to-Liquids Program at the U.S. Department of Energy`s Pittsburgh Energy Technology Center (PETC) is to develop technologies for the production of hydrocarbon fuels and premium chemicals from light alkane gases. PETC`s current Gas-to-Liquids Program comprises the development of four primary advanced conversion technologies, namely, partial oxidation, oxidative coupling, oxyhydrochlorination, and novel conversion processes. Based on the current state of development, it can be concluded that, in the near future, one or more of these technologies will reach proof-of-concept demonstration. Oxyhydrochlorination is the most advanced direct conversion technology, and the synthesis of lower cost methyl chloride from natural gas would impact several commercial technologies that ...
1995-04-01
Experience of HWR nuclear fuel fabrication technology development in Korea
Energy Technology Data Exchange (ETDEWEB)
Since January, 1981, the project of development of nuclear fuel fabrication technology for Wolsung reactor (CANDU type) was undertaken by KAERI(Korea Advanced Energy Research Institute) and successfully fulfilled with loading 24 fuel bundles made by KAERI in Wolsung reactor in September, 1984. On the basis of this accumulated technology and experience, mass production plan to supply all the nuclear fuels for Wolsung reactor is under way. In this presentation, the Korean experience in the development of the nuclear fuel fabrication technology, safety and performance evaluation of KAERI fuel and the results of irradiation of KAERI fuels in Wolsung reactor will be described.
1985-07-01
Experience of HWR nuclear fuel fabrication technology development in Korea
International Nuclear Information System (INIS)
Since January, 1981, the project of development of nuclear fuel fabrication technology for Wolsung reactor (CANDU type) was undertaken by KAERI(Korea Advanced Energy Research Institute) and successfully fulfilled with loading 24 fuel bundles made by KAERI in Wolsung reactor in September, 1984. On the basis of this accumulated technology and experience, mass production plan to supply all the nuclear fuels for Wolsung reactor is under way. In this presentation, the Korean experience in the development of the nuclear fuel fabrication technology, safety and performance evaluation of KAERI fuel and the results of irradiation of KAERI fuels in Wolsung reactor will be described.
1985-10-29
British Library Electronic Table of Contents (United Kingdom)
Early technical history of electric supply to electric railways is briefly reviewed as an introduction to the following seven papers included in this special issue on technologies for saving energy in railway operation. Continuous power supply played a significant role in the early history of railway technologies. The variable voltage variable frequency (VVVF) power electronic technology had also a substantial impact on railway traction systems after 1980s. VVVF technology made it possible to have more efficient drives, downsize rolling stocks, and develop regenerative brakes. Because detailed discussions on each technical development are presented in the following papers, the general remarks of those technologies made in this introduction provide logical links to the ideas presented in th...
2010-01-01
Evolution of health information management and information technology in emergency medicine.
The implementation of information technology will continue to have important effects on the practice of emergency medicine. Patient registration and tracking systems, telemedicine electronic order entry systems, and the advent of electronic health records are some examples of applications that influence patient care in emergency departments. We review the literature regarding information technology advances in emergency medicine and outline the important role that emergency physicians play in developing and implementing a national health information technology strategy. PMID:16712540
2006-06-01
Energy Technology Data Exchange (ETDEWEB)
The report describes the following: overview of the Russian power industry; electric power equipment of Russia; power industry development forecast for Russia; clean coal technology demonstration program of the US Department of Energy; reduction of coal TPS (thermal power station) environmental impacts in Russia; and base options of advanced coal thermal power plants. Terms of the application of clean coal technology at Russian TPS are discussed in the Conclusions.
1995-12-01
Energy Technology Data Exchange (ETDEWEB)
The present report outlines the background and issues supporting the national strategy which was developed to deploy U.S. Government resources most effectively to increase environmental technologies exports and to enhance the trade competitiveness of the U.S. environmental technologies sector. The document is a supplement to the strategic framework.
1994-04-01
Environmental Research Database
DescriptionFollowing publication of the Curry report, DEFRA have made a commitment to establish a number of pilot projects supporting a network of demonstration and development farms. These 'farms' are intended to support the process of technology transfer by giving free access to information on the practical application of new, emerging and best practice technologies. Protected Horticulture has been identified as a sub-sector requiring the establishment of one of these projects. One of the major pressures [continued...
2005-01-31
Electromagnetic forming - a potentially viable technique for accelerator technology
International Nuclear Information System (INIS)
Modern day accelerator development encompasses a myriad technologies required for their diverse needs. Whereas RF, high voltage, vacuum, cryogenics etc., technologies meet their functional requirements, high finish lapping processes, ceramic-metal joining, oven brazing, spark erosion or wire cutting etc., are a must to meet their fabrication requirements. Electromagnetic (EM) forming technique falls in the latter category and is developed as a special technology. It is currently catering to the development as a nuclear reactor technology, but has the potential to meet accelerator requirements too. This paper highlights the general principle of its working, simple design guidelines, advantages, and suggests some specific areas where this could benefit accelerator technologies
2003-02-03
Toward integrated design of waste management technologies
Energy Technology Data Exchange (ETDEWEB)
What technical, economic and institutional factors make radioactive and/or hazardous waste management technologies publicly acceptable? The goal of this paper is to initiate an identification of factors likely to render radioactive and hazardous waste management technologies publicly acceptable and to provide guidance on how technological R&D might be revised to enhance the acceptability of alternative waste management technologies. Technology development must attend to the full range of technology characteristics (technical, engineering, physical, economic, health, environmental, and socio-institutional) relevant to diverse stakeholders. ORNL`s efforts in recent years illustrate some attempts to accomplish these objectives or, at least, to build bridges toward the integrated design of waste management technologies.
1993-11-01
Joining technologies for the plasma facing components of ITER
Energy Technology Data Exchange (ETDEWEB)
An extensive R and D program on the development of the joining technologies between armour (beryllium, tungsten and carbon fibre composites)/copper alloys heat sink and copper alloys/ stainless steel has been carried out by ITER Home Teams. A brief review of this R and D program is presented in this paper. Based on the results, reference technologies for use in ITER have been selected and recommended for further development. (author)
1998-07-01
Development of coal liquefaction technology in Japan
Energy Technology Data Exchange (ETDEWEB)
Coal liquefaction technology aims to obtain a liquid fuel from coal by cracking the coal under elevated temperature and pressure and simultaneously adding hydrogen, either directly as a gas or by way of a suitable solvent. The author describes the work being done on coal liquefaction in Japan, where this technology is being developed as part of a large-scale national project.
1985-01-01
Materials and Components Technology Division research summary, 1992
Energy Technology Data Exchange (ETDEWEB)
The Materials and Components Technology Division (MCT) provides a research and development capability for the design, fabrication, and testing of high-reliability materials, components, and instrumentation. Current divisional programs related to nuclear energy support the development of the Integral Fast Reactor (IFR): life extension and accident analyses for light water reactors (LWRs); fuels development for research and test reactors; fusion reactor first-wall and blanket technology; and safe shipment of hazardous materials. MCT Conservation and Renewables programs include major efforts in high-temperature superconductivity, tribology, nondestructive evaluation (NDE), and thermal sciences. Fossil Energy Programs in MCT include materials development, NDE technology, and Instrumentation design. The division also has a complementary ...
1992-11-01
Human factors assessments of innovative technologies: Robotics sector
International Nuclear Information System (INIS)
The U.S. Department of Energy (DOE) has funded major environmental technology developments over the past several years. One area that received significant attention is robotics, which has resulted in the development of a wide range of unique robotic systems tailored to the many tasks unique to the DOE complex. These systems are often used in highly hazardous environments, which reduces or eliminates worker exposures. The DOE, concurrent with the technology development initiative, also established and funded a 5-yr cooperative agreement intended to interface with the technology development community-with specific attention to the occupational safety and health aspects associated with individual technologies through human factors and hazard assessments. This program is now in its third year.
1997-11-16
An historical perspective of the NERVA nuclear rocket engine technology program. Final Report
Energy Technology Data Exchange (ETDEWEB)
Nuclear rocket research and development was initiated in the United States in 1955 and is still being pursued to a limited extent. The major technology emphasis occurred in the decade of the 1960s and was primarily associated with the Rover/NERVA Program where the technology for a nuclear rocket engine system for space application was developed and demonstrated. The NERVA (Nuclear Engine for Rocket Vehicle Application) technology developed twenty years ago provides a comprehensive and viable propulsion technology base that can be applied and will prove to be valuable for application to the NASA Space Exploration Initiative (SEI). This paper, which is historical in scope, provides an overview of the conduct of the NERVA Engine Program, its organization and management, development philosophy, the engine configuration, and ...
1991-07-01
Organizational model of control of state of technology in the coal industry
Energy Technology Data Exchange (ETDEWEB)
This paper discusses organizational models of planning technology development in coal mining. The following 4 planning systems are analyzed: all-union national system coordinated by the Ministry of Coal Mining of the USSR, all-union associations of coal mine associations (in the Ukrainian SSR the plan is developed by the Ministry of Coal Industry of the Republic), associations of coal mines, coal mines or groups of coal mines. Methods for developing programs for technology development at 4 levels are reviewed. The following planning periods are used: 10 years or more (from 1980 to 1990), a 5 year period and a 1 year period. System for technology development in the Soviet coal industry from 1981 to 1985 is evaluated: research and development programs (20 comprehensive state programs, 36 branch ...
1984-02-01
Energy Technology Data Exchange (ETDEWEB)
Past and current development of coal utilization technology in the Japanese steel industry is reviewed and some projects currently under research and development briefly described. These include DIOS, an iron making process which directly utilizes both iron ore and coal without a sintering plant or a coke oven; and the development of a new generation coke oven. 15 figs.
1994-12-31
Laser Technology for Remote Treatment of Atomic Equipment
International Science & Technology Center (ISTC)
Investigation of Interaction of Laser Radiation with Radioactive Deposits on the metal Surface and Creation of Experimental Stand for Development of Laser Technology for Remote Treatment of Materials Contaminated with Radioactive Substances at the Atomic Power Plants
While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose o...
1995-01-01
Coal to liquids technology (Overview - Research)
... After completing a review into direct coal liquefaction research carried out in Australia and internationally, CSIRO has identified potential new science and technology developments that may improve the cost and viability of CTL in a greenhouse gas-constrained environment. We are conducting research to: determine the optimum ...
Technology and international climate policy
International Nuclear Information System (INIS)
Both the nature of international climate policy architectures and the development and diffusion of new energy technologies could dramatically influence future costs of reducing global emissions of greenhouse gases. This paper explores the implications of interactions between technology availability and performance and international policy architectures for technology choice and the social cost of limiting atmospheric CO2 concentrations to 500 ppm by the year 2095. Key issues explored in the paper include the role of bioenergy production with CO2 capture and storage (CCS), overshoot concentration pathways, and the sensitivity of mitigation costs to policy and technology.
2006-03-15
Commercialization of uncooled infrared technology
BAE Systems is the leading producer of uncooled microbolometer based thermal imaging engines in the world. Initial investments to develop and produce uncooled infrared (IR) technology were primarily driven by military applications, but it was the commercial market with the potential for large product volumes which provided BAE Systems with the business model required for investment in uncooled IR technology. This paper reviews the heritage of BAE Systems technology and current products and is an example of the success of a Dual-Use technology area which DARPA invested in during the 1990s.
2004-10-01
Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)
1988-02-01
Accelerating the output of technology for auxillary processes in open cast mines
Energy Technology Data Exchange (ETDEWEB)
An analysis of the current state of track-laying operations in open-cut mines is given and their labor intensive nature is noted. The lag in the technological development of mechanization equipment for track laying and repair operations is noted. Results are given from developments by the Scientific Research Institute of Open-Pit Mining Operations in the field of mobile transportation technology and promising modular route design. Also examined are the problems of improving the routing bases in the industry. The absence of factories for manufacturing transportation technology and equipment is reflected most evidently in the technical and cost characteristics of coal production by an open-cut method and requires immediate solution.
1984-01-01
The Center for Environmental Technology Innovative Technology Screening Process
Energy Technology Data Exchange (ETDEWEB)
The Center for Environmental Technology`s (CET) mission is to provide a fully integrated system for accelerated evaluation, development, commercialization, and public acceptance of creative environmental solutions which match the foremost demands in today`s environmentally sensitive world. In short, CET will create a means to provide quick, effective solutions for environmental needs. To meet this mission objective, CET has created a unique and innovative approach to eliminating the usual barriers in developing and testing environmental technologies. The approach paves the way for these emerging, cutting-edge technologies by coordinating environmental restoration and waste management activities of industry, universities, and the government to: efficiently and effectively transfer technology to these users, provide market-driven, cost-effective ...
1995-02-01
International Nuclear Information System (INIS)
Plant Assessment Technology (PAT) group, in association with Intelligent System (IS) Group and Engineering Services Department of Malaysian Institute for Nuclear Technology Research (MINT) has developed gamma scanning facilities for on-line investigation of industrial process columns and vessels. The technology, based on the principle of gamma-ray absorption, has been successfully applied for troubleshooting of a number of distillation columns and process vessels in petroleum refineries, gas processing plants and chemical plants in the country and the region. This paper outlines basic characteristics of the system and describes the inspection procedures, and in addition, case studies are also presented. The case studies are purposely chosen to illustrate the versatility of the technology, and furthermore to demonstrate the economic benefits which can be realised from the application ...
1998-10-30
Low-cost technology in renewable energy systems for developing countries
Energy Technology Data Exchange (ETDEWEB)
Renewable energy systems have been suggested as appropriate technologies for developing countries for many years. But they are less attractive to low-income rural and urban populations for reasons of risk and initial capital outlay, and market penetration is usually small as a result. Technology transfer by outside intervention appears unlikely to deliver to enough people in Africa; only self propagating technologies have managed that to date. Unfortunately target populations in developing countries have little capital and are understandably reluctant to take risks. Outside interests see little likelihood of profit and have already demonstrated reluctance to invest in many developing countries. Benefit from technology relies on continued use after purchase and is rightly associated with reliability and availability. Mean time to repair may ...
1995-12-31
Sandia microelectronics development
Energy Technology Data Exchange (ETDEWEB)
An overview of the operations of Sandia`s Microelectronics Development Lab (MDL) is to develop radiation hardened IC, but techniques used for IC processing have been applied to a variety of related technologies such as micromechanics, smart sensors, and packaging.
1997-02-01
International Nuclear Information System (INIS)
Development of the engineering technology basis of pyrometallurgical reprocessing is a key issue for industrialization. For development of the transport technologies of molten salt and liquid cadmium at around 773 K, a salt transport test rig and a metal transport test rig were newly installed in an Ar glove box. Function of the salt transport test rig was confirmed with LiCl-KCl molten salt, and the transport behaviour of molten salt was found to follow that of water. The molten salt/liquid metal contactor for Ln/An separation was newly designed and installed. The test with a single-stage contactor was successful with simulated elements, and a three-stage contactor is now under development. A large-scale electro-refiner with a function to transport molten salt and liquid cadmium were newly designed, and to be installed for demonstration test with simulated materials. (authors)
2006-09-25
Radiation hardening of integrated circuits technologies
International Nuclear Information System (INIS)
The radiation hardening studies started in the mid decade 1960-1970. To survive the different military or space radiative environment, a new engineering science was born, to understand the degradation of electronics components. The different solutions to improve the electronic behavior in such environments have been named 'radiation hardening' of the technologies. Improvement of existing technologies, and qualification methods have been widely studied. However, on the other hand, specific technologies were developed: the Silicon On Insulator technologies for CMOS or Bipolar. The HSOI3HD technology offers today the highest hardening level for the integration density of hundreds of thousand transistors on the same silicon. Full complex systems could be produced on a single die with a technological radiation hardening and no more system ...
Science and technology for industrial ecology
Energy Technology Data Exchange (ETDEWEB)
Scientific and technological communities have a significant role to play and responsibility for the evolution of global sustainability (continuously improving quality of life into the indefinite future). Sustainability is not possible without a substantially improved science and technology basis for industrial ecology. Society needs data and understanding of complex ecological issues to govern itself in a sustainable manner. We should: support and develop multi-disciplinary programs which create the scientific basis for understanding natural and anthropogenic complex systems and for developing environmentally and economically efficient technology; demonstrate a systems-based approach to science and technology issues which is life-cycle comprehensive, integrates environmental considerations, and promotes conservation of natural resources; and encourage ...
1996-07-10
HEMISPHERIC CENTER FOR ENVIRONMENTAL TECHNOLOGY
Energy Technology Data Exchange (ETDEWEB)
FIU-HCET participated in an ICT meeting at Mound during the second week of December and presented a brief videotape of the testing of the Robotic Climber technology. During this meeting, FIU-HCET proposed the TechXtract technology for possible testing at Mound and agreed to develop a five-page proposal for review by team members. FIU-HCET provided assistance to Bartlett Inc. and General Lasertronics Corporation in developing a proposal for a Program Opportunity Notice (PON). The proposal was submitted by these companies on January 5, 1999. The search for new equipment dismantlement technologies is continuing. The following vendors have responded to requests for demonstration: LUMONICS, Laser Solutions technology; CRYO-BEAM, Cryogenic cutting technology; Waterjet Technology Association, Waterjet Cutting ...
1999-01-31
Progress posted in coal liquefaction technology
Energy Technology Data Exchange (ETDEWEB)
This article discusses the latest developments made in the field of technology used for coal liquefaction. Some new areas of development in research and development work are described. Particular consideration is given to low-severity processing. This has two advantages, mostly low-molecular-weight fragments are produced and the extracts are low in heteroatoms. A detailed description of low-severity processing is given. The refining of the liquids produced from coal is also covered.
1986-04-28
Energy Technology Data Exchange (ETDEWEB)
The failure of the standard Growth Approach to economic development to solve the problems of underdevelopment in LDCs has caused an alternative approach, Basic Needs Approach (BNA), to attain prominence in development thought. BNA emphasizes poverty-minimizing growth. Its strategy of direct attack on poverty has better potential for LDCs' development and fulfillment of their populations' basic needs than the trickle-down mechanism of the Growth Approach. BNA requires, among other things, (a) suitable rural financial markets (RFMs) as parts of the overall financial system, and (b) indigenous technological capabilities. The financial system, if it functions as a central element in an institutionalized technology policy, can link technology-related institutions that generate, evaluate, and promote appropriate technologies ...
1988-01-01
International Nuclear Information System (INIS)
Enhancing transport sustainability is the password of national, European, and international policies. The development of innovative solutions is ranging from bio fuels to transport analysis models, materials, traction technologies, mobility management, freight villages.
The role of information technologies in development of new conceptions of crystal chemistry
International Nuclear Information System (INIS)
Russian Oct 2009 p. 130-131 Tajikistan Safiev, KI Saidov, P.Kh. Bozorov,
2009-10-01
The Johns Hopkins Hospital Network
UK PubMed Central (United Kingdom)
The Johns Hopkins Hospital has initiated an ambitious program to apply modern technologies to the development of a new, comprehensive clinical information system. One component of this system is a...Full Text Available
1985-11-13
International Science & Technology Center (ISTC)
Development of Scientific Foundations of the Technology of the Metal Matrix Packing of Leaky Unreprocessible Spent Nuclear Fuel of Different Purpose Reactors for a Long-term Environmentally Safe Storage.
Offshore Wind Electricity: A Viable Energy Option for the Coastal United States
Energy Technology Data Exchange (ETDEWEB)
This paper describes a wide range of technical research and development that can reduce costs and improve technology for deep water deployment.
2007-09-01
Nitride Fuel for Fast Neutron Nuclear Reactors
International Science & Technology Center (ISTC)
Development of Technology for Producing High-Effective Nitride Fuel UN with Controlled Microstructure for Advanced Fast Neutron Nuclear Reactors
NASA Waterjet ... - Technology Transfer Program - Success Stories
A waterjet coating-removal system was developed at NASA's Marshall Space Flight Center in Huntsville, Ala., to remove thermal protective coatings from the ...
Metal-Matrix Composite Processing Technologies for Aircraft ...
... ge aircraft engines (geae) has taken to development an induction plasma deposition (ipd) processing method for the fabrication of ti6242/sic mmc ...
Information Technology Experiences for Students and Teachers (ITEST)
... for the development of IT classroom materials for students or teachers, or for professional ... STEM education. Innovative instructional materials and student assessments, as well as new models ...
International Science & Technology Center (ISTC)
Development of the Technology and Control of Electron-Beam Welding Procedure and Production of Full Scale Sector of Endcap CMS Hadron Calorimeter. Preparation for Mass Production.
Geographic information systems: their use in environmental epidemiologic research.
UK PubMed Central (United Kingdom)
Advances in geographic information system (GIS) technology, developed by geographers, provide new opportunities for environmental epidemiologists to study associations between environmental exposures...Full Text Available
1997-06-01
Sequential development of correlated projects: an application to coal liquefaction
Energy Technology Data Exchange (ETDEWEB)
A sequential research and development programme is considered for which several categories of related technologies are available to develop, each having the potential to produce some final product. At each stage of the programme, an optimal portfolio of technologies is chosen given the information acquired from the previous stages, and those contingent optimal plans are followed in all subsequent stages. The model is applied to coal liquefaction technologies to emphasize the costs that may be incurred by erroneously approaching the development programme as a once-and-for-all endeavour rather than in a sequential framework. The results of the synthetic oil application indicate that the acceleration of the programme may be optimal when the probability of successful development decreases. Under these conditions, adoption of a 'crash ...
1983-01-01
Investigation of the application of remote sensing technology to environmental monitoring
Energy Technology Data Exchange (ETDEWEB)
Activities and results are reported of a project to investigate the application of remote sensing technology developed for the LACIE, AgRISTARS, Forestry and other NASA remote sensing projects for the environmental monitoring of strip mining, industrial pollution, and acid rain. Following a remote sensing workshop for EPA personnel, the EOD clustering algorithm CLASSY was selected for evaluation by EPA as a possible candidate technology. LANDSAT data acquired for a North Dakota test sight was clustered in order to compare CLASSY with other algorithms.
1980-08-01
Energy recovery from waste by use of fluidized-bed technology
Energy Technology Data Exchange (ETDEWEB)
Revolving type fluidized-bed technology, developed by Ebara Corp., is installed in more than 100 facilities worldwide. The technology is applied for waste, coal and in situations where a conventional fluidized bed is difficult to use. Waste and/or coal can be treated and valuable energy can be recovered from a non-renewable source. This paper describes the application of the revolving fluidized bed for waste, coal and tyres.
1999-07-01
Energy research and development. Ninety-Third Congress, First Session, December 1, 1973
The Committee on Interior and Insular Affairs issued the report on a bill to establish a national program for research, development, and demonstration in fuels and energy and for the coordination and financial supplementation of Federal energy research and development; to establish development corporations to demonstrate technologies for shale oil development, advanced power cycle development, geothermal steam development, and coal liquefaction and gasification development; to authorize and direct the Secretary of the Interior to make mineral resources of the public lands available for the development conporations. Comments from governmental agencies on the bill are published. (MCW)
1973-01-01
Energy Technology Data Exchange (ETDEWEB)
In its beginning, the U.S. Department of Energy (DOE) Office of Environmental Management (EM) viewed private industry as lacking adequate technology know-how to meet demands of hazardous and radioactive waste problems at the DOE`s laboratories and nuclear weapons production facilities. In November 1989, EM`s Office of Technology Development (recently renamed the Office of Science and Technology) embarked on a bold program of developing and demonstrating {open_quotes}innovative{close_quotes} waste cleanup technologies that would be safer, faster, more effective, and less expensive than the {open_quotes}baseline{close_quotes} commercial methods. This program has engaged DOE sites, national laboratories, and universities to produce preferred solutions to the problems of handling and treating DOE wastes. More recently, much of this work has shifted to joint efforts ...
1996-12-31
Office of Industrial Technologies research in progress
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy (DOE) Office of Industrial Technologies (OIT) conducts research and development activities which focus on improving energy efficiency and providing for fuel flexibility within US industry in the area of industrial conservation. The mission of OIT is to increase the utilization of existing energy-efficient equipment and to find and promote new, cost-effective ways for industrial facilities to improve their energy efficiency and minimize waste products. To ensure advancement of the technological leadership of the United States and to improve the competitiveness of American industrial products in world markets, OIT works closely with industrial partners, the staffs of the national laboratories, and universities to identify research and development needs and to solve technological challenges. This report contains summaries of the currently active projects ...
1993-05-01
Energy Technology Data Exchange (ETDEWEB)
This study characterized selected commercial volume reduction technologies as to performance and associated costs. VR facility designs were developed for each of the reference VR technologies. Associated on-site storage requirements and cost were also determined. Eight VR technologies were selected for consideration: improved compactor; high pressure compactor (supercompactor); incinerator; fluid bed dryer and incinerator; evaporator crystallizer; evaporator extruder; mobile incinerator; and mobile thin-film evaporator. A representative facility design was developed for each VR technology and for several combinations of technologies. Thirteen separate cases are noted in the following table when retrofit and new facilities are considered.
1984-11-01
Energy Technology Data Exchange (ETDEWEB)
Current Intrusion Detection System (IDS) technology is not suited to be widely deployed inside a Supervisory, Control and Data Acquisition (SCADA) environment. Anomaly- and signature-based IDS technologies have developed methods to cover information technology-based networks activity and protocols effectively. However, these IDS technologies do not include the fine protocol granularity required to ensure network security inside an environment with weak protocols lacking authentication and encryption. By implementing a more specific and more intelligent packet inspection mechanism, tailored traffic flow analysis, and unique packet tampering detection, IDS technology developed specifically for SCADA environments can be deployed with confidence in detecting malicious activity.
2008-05-01
Development of fluidized bed cement sintering technology
Energy Technology Data Exchange (ETDEWEB)
In the new system presented in this paper, the cement clinker is sintered, not in a rotary kiln, but in two different furnaces: a spouted bed kiln and a fluidized bed kiln. The heat generated in the process of cooling the cement clinker is recovered by a fluidized bed cooler and a packed bed cooler, which are more efficient than the conventional coolers. Compared with the rotary kiln system, the new technology significantly reduces NO{sub x} emissions, appreciably cuts energy consumption, and reduces CO{sub 2} emissions as well. Thus, the new system is an efficient cement sintering system that is friendly to the global environment. In this paper, we describe this new technology as one of the applied technologies at an industrial level that is being developed in the Clean Coal Technology Project, and we present the results from test operations at our pilot plant.
1994-12-31
Technological evolution and interdependence in China's emerging biofuel industry
British Library Electronic Table of Contents (United Kingdom)
This study uses the European Patent Office worldwide patent database and applies two-stage interactive data collection methods to reveal the evolving technological interdependence for China's emerging biofuel industry. Three findings are excerpted from our empirical results. First, due to dominant patterns of business ownership, China's biofuel technology is seen as largely based on the evolutionary strength of the foodstuff and chemical fields. Second, China's biofuel technology development has evolved in the mode of 'forward engineering', led by Chinese universities rather than initiated by the public research institutes as in the experience of other East Asian latecomers. Third, our patent map and technology trajectory analyses illustrate that China's biofuel technology tends to be appl...
2011-01-01
Proceedings of the workshop on molten salts technology and computer simulation
Energy Technology Data Exchange (ETDEWEB)
Applications of molten salts technology to separation and synthesis of materials have been studied eagerly, which would develop new fields of materials science. Research Group for Actinides Science, Department of Materials Science, Japan Atomic Energy Research Institute (JAERI), together with Reprocessing and Recycle Technology Division, Atomic Energy Society of Japan, organized the Workshop on Molten Salts Technology and Computer Simulation at Tokai Research Establishment, JAERI on July 18, 2001. In the workshop eleven lectures were made and lively discussions were there on the fundamentals and applications of the molten salts technology that covered the structure and basic properties of molten salts, the pyrochemical reprocessing technology and the relevant computer simulation. The 10 of the presented papers are indexed individually. (J.P.N.)
2001-12-01
Microbial enhanced oil recovery: Entering the log phase
Energy Technology Data Exchange (ETDEWEB)
Microbial enhanced oil recovery (MEOR) technology has advanced internationally since 1980 from a laboratory-based evaluation of microbial processes to field applications. In order to adequately support the decline in oil production in certain areas, research on cost-effective technologies such as microbial enhanced oil recovery processes must focus on both near-term and long-term applications. Many marginal wells are desperately in need of an inexpensive improved oil recovery technology today that can assist producers in order to prevent their abandonment. Microbial enhanced waterflooding technology has also been shown to be an economically feasible technology in the United States. Complementary environmental research and development will also be required to address any potential environmental impacts of microbial processes. In 1995 at this conference, the goal ...
1995-12-31
GRI's Gas Appliance Technology Center Activities at Battelle. Final report, 1986-1992
The Gas Research Institute established the Gas Appliance Technology Center (GATC) in 1982 to develop improved gas appliances. Between 1986 and 1992, the scope of GATC activities at Battelle included technology transfer and overall industry support, residential appliances, commercial appliances, and residential space conditioning. The following tasks are representative of the GATC activities described in the report; gas burner technology, appliance venting, emissions, water heating, range/oven technology, self-powered appliances, commercial cooktop burners, reconstituting ovens, appliance reliability improvement, combination space-heating/water-heating systems, condensing heat exchangers, corrosion testing, and space heating technology. The report includes references to available sources for further reading.
1993-08-01
Data summary of municipal solid waste management alternatives
Energy Technology Data Exchange (ETDEWEB)
The overall objective of the study in this report was to gather data on waste management technologies to allow comparison of various alternatives for managing municipal solid waste (MSW). The specific objectives of the study were to: 1. Compile detailed data for existing waste management technologies on costs, environmental releases, energy requirements and production, and coproducts such as recycled materials and compost. Identify missing information necessary to make energy, economic, and environmental comparisons of various MSW management technologies, and define needed research that could enhance the usefulness of the technology. 3. Develop a data base that can be used to identify the technology that best meets specific criteria defined by a user of the data base. Volume I contains the report text. Volume II contains supporting exhibits. Volumes III through ...
1992-10-01
Vertical-axis wind turbines -- The current status of an old technology
Energy Technology Data Exchange (ETDEWEB)
Vertical-axis wind turbine technology is not well understood, even though the earliest wind machines rotated about a vertical axis. The operating environment of a vertical-axis wind turbine is quite complex, but detailed analysis capabilities have been developed and verified over the last 30 years. Although vertical-axis technology has not been widely commercialized, it exhibits both advantages and disadvantages compared to horizontal-axis technology, and in some applications, it appears to offer significant advantages.
1996-12-31
Technical area status report for chemical/physical treatment. Volume 2, Appendices
Energy Technology Data Exchange (ETDEWEB)
These Appendices describe various technologies that may be applicable to the Mixed Waste Treatment Plant (MWTP) Chemical/Physical Treatment System (CPTS). These technologies were identified by the CPTS Technical Support Group (TSG) as potentially applicable to a variety of separation, volume reduction, and decontamination requirements. The purpose was to identify all available and developing technologies, and their characteristics, for subsequent evaluation for specific requirements identified for the CPTS. However, the technologies described herein are not necessarily all inclusive, nor are they necessarily all applicable.
1993-08-01
Innovative technology summary report: in situ air stripping using horizontal wells
Energy Technology Data Exchange (ETDEWEB)
In situ air stripping (ISAS) technology was developed to remediate soils and ground water contaminated with volatile organic compounds (VOCs) both above and below the water table. ISAS employs horizontal wells to inject (sparge) air into the ground water and vacuum extract VOCs from vadose zone soils. The innovation is creation of a system that combines two somewhat innovative technologies, air sparging and horizontal wells, with a baseline technology, soil vapor extraction, to produce a more efficient in situ remediation system.
1995-04-01
Identification of data gaps and research needs for solid wastes from synfuel technologies
This report presents an overview of research activity currently being funded by the US Department of Energy (DOE) on solid wastes from coal gasification, coal liquefaction, and oil shale technologies, Projects conducted in the DOE energy technology centers and national laboratories, and in cooperative projects with other government agencies, private industry, and universities are developing the basic and applied technology and data on which present and future fuel-conversion and utilization processes depend. The report identifies data gaps and recommends research needs where warranted.
1982-03-01
CyberKnife SRS: new technologies that enhance the treatment of cancer
International Nuclear Information System (INIS)
The CyberKnife Robotic Radiosurgery System (Accuracy Incorporated, Sunnyvale, CA, USA) is used worldwide to treat tumors and neurological disorders anywhere in the body with sub-millimetre beam delivery accuracy. Accuracy has developed a number of new technologies in recent years to enhance the treatment of cancer patients. Such new technologies include a fast Monte Carlo Dose Calculation algorithm, Sequential Optimization dose planning, the IrisTM Variable Aperture Collimator, an 800 MU/min Linear Accelerator, and Optimized Path Traversal. These technologies enable physicists and physicians to plan treatments quickly and easily and deliver them with unrivalled accuracy and precision
2008-11-26
DECONTAMINATION SYSTEMS AND INFORMATION RESEARCH PROGRAM
Energy Technology Data Exchange (ETDEWEB)
During the five plus years this Cooperative Agreement existed, more than 45 different projects were funded. Most projects were funded for a one year period but there were some, deemed of such quality and importance, funded for multiple years. Approximately 22 external agencies, businesses, and other entities have cooperated with or been funded through the WVU Cooperative Agreement over the five plus years. These external entities received 33% of the funding by this Agreement. The scope of this Agreement encompassed all forms of hazardous waste remediation including radioactive, organic, and inorganic contaminants. All matrices were of interest; generally soil, water, and contaminated structures. Economic, health, and regulatory aspects of technologies were also within the scope of the agreement. The highest priority was given to small businesses funded by the Federal Energy Technology Center (FETC) and Department of Energy (DOE) involved in ...
1998-11-01
Subsurface contaminants focus area
Energy Technology Data Exchange (ETDEWEB)
The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within ...
1996-08-01
Energy Technology Data Exchange (ETDEWEB)
Coal can be converted to liquid fuels via three generically defined technologies: pyrolysis, direct hydroliquefaction, and indirect liquefaction. This paper presents a general overview of the indirect liquefaction technology and a discussion of processes tht are commercially available as well as those in the development stage. Finally, the objective of the DOE research and development program in conversion of synthesis gas derived from coal to transportation fuels is summarized. The current outlook for indirect liquefaction is encouraging. New facilities are being built in South Africe and New Zealand, and commercial plants could be designed and built for operation in the United States using proven technology. At the same time, developments in gasification as well as liquefaction catalysts and reactor technology promise significant ...
1982-01-01
Draft Regulatory Rule-making for On-line Maintenance of Nuclear Power Plants
International Nuclear Information System (INIS)
Internationally, on-line maintenance (OLM) of nuclear power plants under the operation is prevailed to enhance nuclear safety and economics. In recent years, Korea Hydro and Nuclear Power Co. Ltd. (KHNP) is eager to apply OLM. Ministry of Education, Science and Technology (MEST) has established the related technology development program as an item of 'Overall Planning on Nuclear Safety(2010-2014)' through acceptance to the request of KHNP in 2009. OLM is defined as maintenance that is performed with the main generator connected to the grid. In other words, it means a preventive maintenance to be implemented during the allowable outage time (AOT) with ignoring inoperability of safety-related equipment listed in the technical specifications. The Korea Institute of Nuclear Safety (KINS) is developing the assessment technology of safety concerns for OLM under the auspices of MEST. Draft ...
2010-10-01
The development of fast breeder reactors
International Nuclear Information System (INIS)
Modern civilisation is based on substantial utilisation of energy. Rapid industrial development and improvement of living standards in India require energy planners to adequately forecast the energy demand and take appropriate measures in advance. However, the development and establishment of new technology is a slow process, sometimes extending over decades. Hence, energy options based on new technologies need to be planned for much in advance making allowance for uncertainties and delays. Fast Breeder Reactor (FBR) technology is an advanced energy option promising abundant and economic supply of power. Research and development work on FBRs has been conducted at the Indira Gandhi Centre of Atomic Research (IGC) since 1971. The international trends in FBR development are highlighted in this discussion and an overview of some of the research ...
Opportunities and issues in international photovoltaic market development
Energy Technology Data Exchange (ETDEWEB)
The confluence of technology development and market readiness is opening up major business opportunities for photovoltaic (PV) systems throughout the developing world. The National Renewable Energy Laboratory (NREL) and Sandia National Laboratories in Abuquerque (Sandia), working on behalf of the U.S. Department of Energy, have launched pilot projects in several countries throughout the world over the past 3 years. The focus of these pilot projects has been the development of in-country institutional capabilities necessary to deliver the promise of PV electricity to the rural populations. In addition to country-specific activities, NREL is conducting several technology, information, and partnership projects focused on further accelerating the education, training, business, and technology developments necessary to bridge the gap between ...
1996-05-01
Research and development for the upgrading of Rhenish brown coal
Energy Technology Data Exchange (ETDEWEB)
Product control procedures, the development of new technologies, and the extension of the applications of solid fuels are described. Hydrogasification and high-temperature Winkler gasification are discussed. The design and function of a continuous, semi-industrial plant for hydrogenating liquefaction in the sump phase are gone into. (MOS).
1988-07-01
International Nuclear Information System (INIS)
This article examines the effects of competition of geothermal energy production with other technologies. The topics of the article include near-term market growth, cause for cautious optimism, limits to development of geothermal energy production, economic arguments for development of geothermal power plants, the effects of a competitive market on industry survival.
GSFC Information Systems Technology Developments Supporting the Vision for Space Exploration.
The Vision for Space Exploration will guide NASA's future human and robotic space activities. The broad range of human and robotic missions now being planned will require the development of new system-level capabilities enabled by emerging new technologie...
2005-01-01
Energy Technology Data Exchange (ETDEWEB)
This progress report presents a detailed description of the background, technology and application, and Statement of Work for the development of a coal-fired pulse combustor for residential space heating.
1986-12-31
UK PubMed Central (United Kingdom)
BackgroundDengue fever is a mosquito-borne illness that places significant burden on tropical developing countries with unplanned urbanization. A surveillance system using Google...Full Text Available
Acetylsalicylic acid as soluble tablets
International Science & Technology Center (ISTC)
Realization of Pharmacological Tests, Development of the Specifications and Technical Documentation and Registration in the Russian Federation of Medical Products as Soluble Tablets of Acetylsalicylic Acid/Calcium Carbonate in Two Dosages Intended for use as Medical Products Smoothing, Febrifugal and Antiaggregation Action and Development of Technology of Tableting the Above-Stated Preparations
Trends in robotics: A summary of the Department of Energy`s critical technology roadmap
Energy Technology Data Exchange (ETDEWEB)
Technology roadmaps serve as pathways to the future. They call attention to future needs for research and development; provide a structure for organizing technology forecasts and programs; and help communicate technological needs and expectations among end users and the research and development (R and D) community. Critical Technology roadmaps, of which the Robotics and Intelligent Machines (RIM) Roadmap is one example, focus on enabling or cross-cutting technologies that address the needs of multiple US Department of Energy (DOE) offices. Critical Technology roadmaps must be responsive to mission needs of the offices; must clearly indicate how the science and technology can improve DOE capabilities; and must describe an aggressive vision for the future of the technology itself. ...
1998-08-10
The development and application of photonic technology in infrared and electro-optic countermeasures
In this paper we discuss recent work at the Advanced Technology Centre of BAE Systems on photonic technology, in particular photonic crystal fibres, applied to infra-red and electro-optic countermeasure systems. The use of Photonic Crystal fibres or holey fibres in countermeasure systems could significantly simplify platform integration by enabling remote location of laser sources, the generation of multiple wavelengths or continuum generation from a single pump source .The paper will describe the development of these fibres, drawing examples from recent civil collaborative research projects such as PFIDEL and LAMPS.
2007-10-01
Technology development tendency and R and D idea of NPP radiation monitoring system
International Nuclear Information System (INIS)
This paper gives a general description of functions, usages and system configurations of the instruments and their major units or components of the radiation monitoring system, as well as the status and technical gap between domestic and foreign technologies. And then the paper also puts forward an idea on product R and D, i.e. combination of independent R and D and innovation, assimilation and re-innovation of foreign advanced technology at present situation in order to keep pace with the rapid development of nuclear power in China and achieve the goal of localization of nuclear power equipment. (authors)
2009-06-01
Sophisticated applications of radiation heat transfer
International Nuclear Information System (INIS)
A large amount of energy has been consumed so far in so called matured industries such as iron and steel, oil refinery, petrochemical, ceramic, paper and pulp manufacturing and so forth. A successive stimulation on the preceding industries has to be enhanced from a technological viewpoint in order to maintain a further development based on novel and innovative technologies. In this regard, energy technology has become and will be increasingly important in a high temperature system so that the basic concept for heat transfer augmentation methods by thermal radiation is reviewed briefly in accord with the recent developments together with theoretical background and the prominent features. The heat transfer augmentation related to thermal radiation is summarized.
1987-01-01
Nanocomposites: a review of technology and applications
British Library Electronic Table of Contents (United Kingdom)
Purpose - This paper aims to describe the technology and applications of nanocomposite materials. Design/methodology/approach - This paper discusses products, applications and technological developments in polymer, ceramic and metal nanocomposites. It concludes with a brief consideration of electronic component applications. Findings - It is shown that polymer nanocomposites and the materials used in their production are commercially available and finding applications in several industries, including automotive, military, food, electronics and leisure, due to their enhanced mechanical, electrical and thermal properties. Ceramic and metallic nanocomposites are at an earlier stage of development and a critical issue to resolve is optimising the dispersion of nanomaterials in the matrices. Pa...
2011-01-01
High-tech hydro: an overview of pumped storage
A growing number of pumped storage plants installed within the US brings attention to the increasing significance of pumped storage as a source of electrical generation capacity. Because of the special benefits this technology has to offer, hydroelectric pumped storage is an option that many utilities should consider for the supply of new capacity requirements. This article surveys the development and use of pumped storage in the US, and considers the potential for the future development of this technology. Although some of the problems that have occurred on recent projects highlight the role of pumped storage as a technological proving ground, the article puts forth the view that pumped storage is maturing to play a significant role in US electricity supply.
Challenges of efficient and clean use of fossil fuels for power production
Energy Technology Data Exchange (ETDEWEB)
Constantly increasing resource efficiency together with the broad introduction of CCS technologies is fundamental for a continuous use of fossil fuels in power generation against the background of up-coming requirements for CO2 emission reduction. In principle, CCS means up-grading conventional power plant technology with proven CO2 removal processes. However, this leads to additional losses, auxiliary power demand and cost. System integration, development or at least adaption of components and processes are the main requirements in this context. Different technology solutions and recent developments will be addressed as well as challenges when implementing in demonstration projects.
2010-09-15
Status Report A Review of Slimhole Drilling
Energy Technology Data Exchange (ETDEWEB)
This 1994 report reviews the various applications of slimhole technology including for exploration in remote areas, low-cost development wells, reentering existing wells, and horizontal and multilateral drilling. Advantages of slimholes to regular holes are presented. Limitations and disadvantages of slimholes are also discussed. In 1994, slimhole drilling was still an ongoing development technology. (DJE 2005)
1994-09-01
Power and ecological aspects of hydrogen and hydrogenous gas usage
International Nuclear Information System (INIS)
General trends of developing hydrogen power engineering and technology in Ukraine are considered. Based on a general level of power consumption and real opportunities for hydrogen production, a conclusion is derived that there are possibilities in the near future to partially replace conventional hydrocarbon fuels by hydrogen. Besides, developed technologies for burning hydrogenous gases and hydrogen-fuel systems when applied to transport installations allow one to improve essentially their power and ecological characteristics. 5 refs.
Nova Scotia Research Foundation Corporation 1989/90 annual report. [Canada - Nova Scotia
Energy Technology Data Exchange (ETDEWEB)
The Nova Scotia Research Foundation Corporation was established in 1946 by the Province of Nova Scotia to use science and technology to assist in the economic development of Nova Scotia. Within the Applied Science Division of the Corporation, research and development programs in the area of coal and mineral technology have been undertaken. A brief description of two projects -- coal liquefaction and coal-water fuels, are reported.
1990-09-01
Energy Technology Data Exchange (ETDEWEB)
Contents of this report are under the following topical sections: Legal Authority; Summary and Scope; Data Collection Activities; Industry Description; Industry Subcategorization; Water Use and Wastewater Characterization; Pollutants Selected for Regulation; Pollution Prevention and Wastewater Treatment Technologies; Development of Control and Treatment Options; Costs of Technology Bases for Regulations; Pollutant Reduction Estimates; Non-Water Quality Impacts; Implementation of Proposed Effluent Limitation Guidelines and Standards; Analytical Methods; and Glossary.
1998-05-01
Ceramic dome receiver technology developments
Energy Technology Data Exchange (ETDEWEB)
The development and experimental demonstration of a high-temperature seal for the SHARE ceramic dome cavity receiver is reported. The mechanical contact seal which was tested on one-foot-diameter silicon-carbide ceramic-dome hardware at pressure differentials to four atmospheres and dome temperatures to 2200/sup 0/F (1200/sup 0/C) showed negligible leakage at expected receiver operating conditions. Potential solar receiver applications for the technology are illustrated.
1980-01-01
Energy Technology Data Exchange (ETDEWEB)
This report describes the fiscal 1998 result on development of genome informatics technology. As comparative analysis technique of genes, the combination of electrophoresis and PCR was used. For improvement of the throughput and reproducibility of the technique, module- shuffling primers were used, and the multi(96)-arrayed capillary fragment analyzer was devised. The system detecting SNPs rapidly was also developed successfully. As analysis technology of DNA sequence by use of triple- stranded DNA formation, study was made on construction of long cDNA libraries, selective subtraction of specific sequences from libraries, and the basic technology of homologous cloning. Study was also made on each reaction step of IGCR technique for fast analysis, and specifications of a fluorescence transfer monitor. As modeling technique of genetic sequence information, the simulation model was ...
1999-03-01
Development of radioisotope tracer technology
Energy Technology Data Exchange (ETDEWEB)
The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer ...
2000-04-01
International Nuclear Information System (INIS)
In the future even more than in the past, nuclear power will be indispensable in the present industrialized countries and in those still under development. The safe, nonpolluting, and economic supply of energy to mankind in the future includes so many different problems that the technology of the high-temperature reactor at its present level of development, and with the possibilities is offers above and beyond those provided by other, established, technologies, does not have to mark the end of some old line of development, but rather should be seen as the starting point of a development offering promise for the future. It is for this very reason that the extensive, valuable knowledge and experience accumulated in the construction, operation, and decommissioning of the AVR and THTR plants, the development of the HTR module and other variants ...
The market potential for SMES in electric utility applications. Final report
Energy Technology Data Exchange (ETDEWEB)
Superconducting magnetic energy storage (SMES) is an emerging technology with features that are potentially attractive in electric utility applications. This study evaluates the potential for SMES technology in the generation, transmission, distribution, and use of electric energy; the time frame of the assessment is through the year 2030. Comparisons are made with other technology options, including both commercially available and advanced systems such as various peaking generation technologies, transmission stability improvement technologies, and power quality enhancement devices. The methodology used for this study focused on the needs of the market place, the capabilities of S and the characteristics of the competing technologies. There is widespread interest within utilities for the development of SMES technology, ...
1994-06-01
Hazardous waste treatment and environmental remediation research
Energy Technology Data Exchange (ETDEWEB)
Los Alamos National Laboratory (LANL) is currently evaluating hazardous waste treatment and environmental remediation technologies in existence and under development to determine applicability to remediation needs of the DOE facilities under the Albuquerque Operations Office and to determine areas of research need. To assist LANL is this effort, Science Applications International Corporation (SAIC) conducted an assessment of technologies and monitoring methods that have been demonstrated or are under development. The focus of this assessment is to: (1) identify existing technologies for hazardous waste treatment and environmental remediation of old waste sites; (2) identify technologies under development and the status of the technology; (3) assess new technologies that need ...
1989-09-29
Energy Technology Data Exchange (ETDEWEB)
For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by ...
1998-03-01
Commissioning and operation of BHP`s LCM plant
Energy Technology Data Exchange (ETDEWEB)
BHP Petroleum (BHPP) has now operated the 164 tonne per day Methanol Research Plant (MRP) located on the outskirts of Melbourne, Australia for over one year. This plant was commissioned in 1994 making first methanol on 17th October and has operated since then, selling product by pipeline to two local customers, ICI Adhesives and Borden Australia. The plant is based on the Leading Concept Methanol technology (LCM) licensed from ICI Katalco. Since 1985 BHPP has been involved in the development of Floating Production Storage and Offloading (FPSO) technology for the production of oil and gas offshore. In order to utilize the gas associated with oil on remote offshore oil production facilities the combination of gas conversion to methanol and existing FPSO technology is being investigated. The LCM technology being commercialized at the MRP is part of the strategy to demonstrate and ...
1995-12-31
FY04 Engineering Technology Reports Technology Base
Energy Technology Data Exchange (ETDEWEB)
Lawrence Livermore National Laboratory's Engineering Directorate has two primary discretionary avenues for its investment in technologies: the Laboratory Directed Research and Development (LDRD) program and the ''Tech Base'' program. This volume summarizes progress on the projects funded for technology-base efforts in FY2004. The Engineering Technical Reports exemplify Engineering's more than 50-year history of researching and developing (LDRD), and reducing to practice (technology-base) the engineering technologies needed to support the Laboratory's missions. Engineering has been a partner in every major program and project at the Laboratory throughout its existence, and has prepared for this role with a skilled workforce and technical resources. This accomplishment is well summarized by ...
2005-01-27
Office of Industrial Technologies: Summary of program results
Energy Technology Data Exchange (ETDEWEB)
Working in partnership with industry, the US Department of Energy`s (DOE`s) Office of Industrial Technologies (OIT) is helping reduce industrial energy use, emissions, and waste while boosting productivity. Operating within the Office of Energy Efficiency and Renewable Energy (EE), OIT conducts research, development, demonstration, and technology transfer efforts that are producing substantial, measurable benefits to industry. This document summarizes some of the impacts of OIT`s programs through 1997. OIT tracks energy savings as well as other benefits associated with the successfully commercialized technologies resulting from OIT-supported research partnerships. Specifically, a chart shows current and cumulative energy savings as well as cumulative reductions of various air pollutants including particulates, volatile organic compounds (VOCs), nitrogen oxides (NO{sub x}), sulfur oxides (SO{sub x}), and ...
1999-01-01
Energy Technology Data Exchange (ETDEWEB)
Unlike markets for storable commodities, electricity markets depend on the real-time balance of supply and demand. Although much of the present-day grid operate effectively without storage technologies, cost-effective ways of storing electrical energy can make the grid more efficient and reliable. This work addresses an economic comparison between emerging and traditional Electric Energy Storage (EES) technologies in a competitive electricity market. In order to achieve this goal, an appropriate Self-Scheduling (SS) approach must first be developed for each of them to determine their maximum potential of expected profit among multi-markets such as energy and ancillary service markets. Then, these technologies are economically analyzed using Internal Rate of Return (IRR) index. Finally, the amounts of needed financial supports are determined for choosing the emerging technologies ...
2009-12-15
Energy Technology Data Exchange (ETDEWEB)
The oil shale PCTM for Modified In Situ Oil Shale Retorting combined with Lurgi Surface Retorting addresses the application of this combination of technologies to the development of oil shale resources in the western United States. This manual describes the combined plant using Lurgi surface retorting technology (developed by Lurgi Kohle and Mineralotechnik GmbH, West Germany) and the Modified In Situ process (developed by Occidental Oil Shale, Inc.) proposed by Occidental Oil Shale, Inc. and Tenneco Shale Oil Company for use in the development of their Federal oil shale lease Tract C-b in western Colorado. Since details regarding waste streams and control technologies for the Lurgi process are presented in a separate PCTM, this document focuses principally on the Modified In Situ process.
1983-04-01
Canadian fuel development program in 1997/98
International Nuclear Information System (INIS)
This paper describes the CANDU fuel development activities in Canada during 1997 through 1998. The activities include those of the Fuel Technology Program sponsored by the CANDU Owners Group. The goal of the Fuel Technology Program is to maintain and improve the reliability, economics and safety of CANDU fuel in operating reactors. These activities, therefore, concentrate on the present designs of 28-element and 37-element fuel bundles. The Canadian fuel development activities also include those of the Advanced Fuel and Fuel Cycle Technology Program at AECL. These activities concentrate on the development of advanced fuel designs and advanced fuel cycles, which among other advantages, can reduce the capital and fuelling costs, maintain operating margins in aging reactors, improve natural-uranium utilization, and reduce the amount of spent fuel. (author)
1997-09-21
Wiley::The Wiley Encyclopedia of Packaging Technology, 3rd Edition
...The+Wiley+Encyclopedia+of+Packaging+Technology%2C+3rd+Edition FO21+Food+Packaging Wiley::The Wiley Encyclopedia of Packaging Technology, 3rd Edition WILEY ...US | HELP Home / Chemistry / Food Science & Technology / Food Processing, Production & Manufacture / Food Packaging / The Wiley Encyclopedia of Packaging Technology, 3rd Edition ...Manufacture Sensory Science Food Biotechnology Food Chemistry Food Engineering Related Titles Food Packaging Brewing Yeast and Fermentation by Chris Boulton, David Quain Food ...Editor) Journal of Food Process Engineering Journal of Food Processing and Preservation Packaging Research in Food Product Design and Development by Howard R. ...
British Library Electronic Table of Contents (United Kingdom)
It is necessary to remove chlorine efficiently from municipal waste plastics (MWP) that contain polyvinyl chloride (PVC) and other plastics containing chlorine. In this article we consider thermal degradation liquefaction technology. In Japan, the chlorine content of reclamation oil products must be kept below 100 ppm owing to the quality standard for pyrolysis oil. Liquefaction dechlorination technology for MWP is still an important issue to study. The twin-screw extruder that has been developed as dechlorination technology for blast furnaces and coke ovens has a shorter residence time for dechlorination than other dechlorination technologies. In this article, we used a single-screw extruder for the dechlorination process because it also has a short residence time. Experiments on the dech...
2010-01-01
Strengthening Clean Energy Technology Cooperation under the UNFCCC: Steps toward Implementation
Energy Technology Data Exchange (ETDEWEB)
Development of a comprehensive and effective global clean technology cooperation framework will require years of experimenting and evaluation with new instruments and institutional arrangements before it is clear what works on which scale and in which region or country. In presenting concrete examples, this paper aims to set the first step in that process by highlighting successful models and innovative approaches that can inform efforts to ramp up clean energy technology cooperation. This paper reviews current mechanisms and international frameworks for global cooperation on clean energy technologies, both within and outside of the UNFCCC, and provides selected concrete options for scaling up global cooperation on clean energy technology RD&D, enabling environment, and financing.
2010-08-01
Energy Technology Data Exchange (ETDEWEB)
Kawasaki Steel started the construction of an automatic steel strip coil transportation system in the 1980's. Presently, most of the in-plant transportation of hot-rolled or cold-rolled coils are automated. For establishing the automatic transportation, there were developed various technologies, such as, the optimum handling technology using artificial intelligence, the technology of preventing additional piling of coils on existing coils by using an ultrasonic wave and a laser beam. Through the improvements of these technologies, a full-automated transportation system has been achieved and the system has contributed substantially toward product quality assurance and cost reduction. This paper gives the changes in the automation technology of coil transportation in the automation of No. 3 finishing hot rolling mill, now having the latest automatic ...
1999-12-01
Separation science and technology. Semiannual progress report, April 1992--September 1992
Energy Technology Data Exchange (ETDEWEB)
This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1992. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Two other projects are underway with the objective of developing (1) a membrane-assisted solvent extraction method for treating natural and process waters contaminated by volatile organic compounds and (2) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process.
1994-09-01
Recent advance of focused ion beam technology in maskless deposition and patterning
International Nuclear Information System (INIS)
The present article will review recent advances in focused ion beam (FIB) technology. With increasing demands for scale of integration, microfabrication technology is becoming more important and various new microfabrication tools and processing techniques are desired. FIB is one of the promising tools for future microfabrication technology. This provides maskless patterning capability, which is of importance for process simplification, nanofabrication and in the development of in situ vacuum processing. In situ vacuum processing systems are being developed by combining FIB and a molecular beam epitaxy system. Radiation damage may limit applications of FIB. However, it was demonstrated that low energy FIB (<1 keV) with very high brightness was reached and promising results for low damage processing have been obtained. (orig.).
Federal Geothermal Research Program Update Fiscal Year 1999
Energy Technology Data Exchange (ETDEWEB)
The Department of Energy (DOE) and its predecessors have conducted research and development (R&D) in geothermal energy since 1971. To develop the technology needed to harness the Nation's vast geothermal resources, DOE's Office of Geothermal and Wind Technologies oversees a network of national laboratories, industrial contractors, universities, and their subcontractors. The following mission and goal statements guide the overall activities of the Office of Geothermal and Wind Technologies. This Federal Geothermal Program Research Update reviews the specific objectives, status, and accomplishments of DOE's Geothermal Program for Federal Fiscal Year (FY) 1999. The information contained in this Research Update illustrates how the mission and goals of the Office of Geothermal and Wind Technologies are reflected in each R&D ...
2004-02-01
Energy Technology Data Exchange (ETDEWEB)
The research and development for the first year of the project are performed through specialization of researchers, information from aborad and international cooperation, securement of advanced nuclear technology, development and installation of test equipment, application of external man-power, establishment of advanced test techniques, and certified test method. 1. Absolute efficiency measurement examination technology development of gamma scanning system 2. Sample preparation technology development of SEM and EPMA for micro-structural observation and chemical composition analysis 3. Irradiated high burn-up nuclear fuel transportation and test for PWR 4. Development of hot cell examination techniques and equipment 5. Acquirement of KOLAS system. In addition to the project, the following activities are carried out as ...
2002-12-01
Energy Technology Data Exchange (ETDEWEB)
Developing and deploying innovative environmental cleanup technologies is an important goal for the U.S. Department of Energy (DOE), which faces challenging remediation problems at contaminated sites throughout the United States. Achieving meaningful, constructive stakeholder involvement in cleanup programs, with the aim of ultimate acceptance of remediation decisions, is critical to meeting those challenges. DOE`s Office of Technology Development sponsors research and demonstration of new technologies, including, in the past, the Volatile Organic Compounds Arid Site Integrated Demonstration (VOC-Arid ID), hosted at the Hanford Site in Washington State. The purpose of the VOC-Arid ID has been to develop and demonstrate new technologies for remediating carbon tetrachloride and other VOC contamination in soils and ground water. In October 1994 ...
1995-05-01
Energy Technology Data Exchange (ETDEWEB)
Guidelines and ground rules followed in the development of requirements for the SPS are presented. Development planning objectives are specified in each of these areas, and evolutionary SPS program scenarios are described for the various concepts studied during the past one year contract. Program descriptions are presented as planning packages of technical tasks, and schedule phasing. Each package identifies the ground based technology effort that will facilitate SPS definitions, designs, development, and operations.
1981-03-01
Future of X-ray phase imaging in medical imaging technology
International Nuclear Information System (INIS)
Weakly absorbing materials, such as biological, soft tissues, can be imaged by generating contrast due to the phase shift of X-rays. In the past decade, several methods for X-ray phase imaging were proposed and demonstrated. The performance of X-ray phase imaging is attractive in the field of medical imaging technology, and its development for practical use is expected. Many methods, however, have been developed under the assumption of the use of synchrotron radiation, which is an obstacle to practical use. The method based on Talbot (-Lau) interferometry enables us to use a compact X-ray source, and its development is expected as a breakthrough for medical applications. (author)
2007-04-01
Exploratory battery technology development and testing report for 1989
Energy Technology Data Exchange (ETDEWEB)
Sandia National Laboratories, Albuquerque, has been designated as Lead Center for the Exploratory Battery Technology Development and Testing Project, which is sponsored by the US Department of Energy's Office of Energy Storage and Distribution. In this capacity, Sandia is responsible for the engineering development of advanced rechargeable batteries for both mobile and stationary energy storage applications. This report details the technical achievements realized in pursuit of the Lead Center's goals during calendar year 1989. 4 refs., 84 figs., 18 tabs.
1990-12-01
Energy Technology Data Exchange (ETDEWEB)
The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through February 1999.
1999-03-01
Energy Technology Data Exchange (ETDEWEB)
The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through September 1999.
1999-10-01
International Nuclear Information System (INIS)
Within the framework of the EU power plant conceptual study (PPCS), a modular He-cooled divertor concept with integrated pin array (HEMP) is being developed at the Forschungszentrum Karlsruhe. The design goal is to achieve a high heat flux of at least about 10-15 MW/m"2, which is proposed for a near-term reactor model like DEMO. The development and optimization of the divertor concept require a close link between the main issues: design, analyses, materials and fabrication technology, and experiments with feedbacks between them to be accounted for. Design-specific requirements on materials and fabrication issues will be discussed.
2004-08-01
Coal development potential in Pakistan
Energy Technology Data Exchange (ETDEWEB)
A total of 48 papers were presented, and covered the following topics: the current situation in Pakistan with respect to development and utilization of coal resources; the policies that have been responsible for the development and utilization of coal resources in Pakistan; coal development and utilization in other developing nations e.g. Indonesia, Greece, Philippines, China, Thailand and Haiti; and technological developments in coal exploration; extraction, handling, transport and utilization which could accelerate future development of Pakistan's coal resources. Specific subjects covered include the use of coal in the cement industry of Pakistan; the production of briquettes for domestic use, development and training of personnel for the coal industry; and sources of finance for coal ...
1986-01-01
Energy Technology Data Exchange (ETDEWEB)
The Department of Energy`s Office of Technology Development initiated an Integrated Demonstration Program at the Savannah River Site in 1989. The objective of this program is to develop, demonstrate, and evaluate innovative technologies that can improve present-day environmental restoration methods. The Integrated Demonstration Program at SRS is entitled ``Cleanup of Organics in Soils and Groundwater at Non-Arid Sites.`` New technologies in the areas of drilling, characterization, monitoring, and remediation are being demonstrated and evaluated for their technical performance and cost effectiveness in comparison with baseline technologies. Present site characterization and monitoring methods are costly, time-consuming, overly invasive, and often imprecise. Better technologies are required to accurately describe the subsurface geophysical and ...
1993-12-31
Technology development, evaluation, and application (TDEA) FY 1997 progress report
Energy Technology Data Exchange (ETDEWEB)
The public expects that the Los Alamos National Laboratory (LANL) will operate in a manner that prevents negative impacts to the environment and protects the safety and health of its employees and the public. To achieve this goal within budget, the Department of Energy (DOE) and LANL must develop new and improved environment, safety, and health (ES and H) technologies and implement innovative, more cost-effective ES and H approaches to operations. In FY95, the Environment, Safety, and Health (ESH) Division initiated a Technology Development, Evaluation, and Application (TDEA) program. The purpose of this unique program is to test and develop technologies that solve LANL ES and H problems and improve the safety of LANL operations. This progress report presents the results of 10 projects funded in FY97 by the TDEA Committee of the Environment, Safety, and Health ...
1998-05-01
Graphite Technology Development Plan
Energy Technology Data Exchange (ETDEWEB)
This technology development plan is designed to provide a clear understanding of the research and development direction necessary for the qualification of nuclear grade graphite for use within the Next Generation Nuclear Plant (NGNP) reactor. The NGNP will be a helium gas cooled Very High Temperature Reactor (VHTR) with a large graphite core. Graphite physically contains the fuel and comprises the majority of the core volume. Considerable effort will be required to ensure that the graphite performance is not compromised during operation. Based upon the perceived requirements the major data needs are outlined and justified from the perspective of reactor design, reatcor performance, or the reactor safety case. The path forward for technology development can then be easily determined for each data need. How the data will be obtained and the inter-relationships between the experimental ...
2007-09-01
Development of Risk Management Technology/Development of Risk-Informed Application Technology
Energy Technology Data Exchange (ETDEWEB)
This project aims at developing risk-informed application technologies to enhance the safety and economy of nuclear power plant altogether. For this, the Integrated Level 1 and 2 PSA model is developed. In addition, the fire and internal flooding PSA models are improved according to the PSA standard of U.S.A. To solve the issues of domestic PSA model, the best-estimate thermal hydraulic analyses are preformed for the ATWS and LSSB. In order to reduce the uncertainty of PSA, several new PSA technologies are developed: (1) more exact quantification of large fault tree, (2) importance measure including the effects of external PSA. As feasibility studies of Option 2 and 3, the class of 6 systems' SSC are re-classified based on the risk information and the sensitivity analyses is performed for the EDG starting time, respectively. It is also improved that the methodology to ...
2007-06-15
International Nuclear Information System (INIS)
Protecting sensitive items from undetected tampering in an unattended environment is crucial to the success of non-proliferation efforts relying on the verification of critical activities. Tamper Indicating Packaging (TIP) technologies are applied to containers, packages, and equipment that require an indication of a tamper attempt. Examples include: the transportation and storage of nuclear material, the operation and shipment of surveillance equipment and monitoring sensors, and the retail storage of medicine and food products. The spectrum of adversarial tampering ranges from attempted concealment of a pin-hole sized penetration to the complete container replacement, which would involve counterfeiting efforts of various degrees. Sandia National Laboratories (SNL) has developed a technology base for advanced TIP materials, sensors, designs, and processes which can be adapted to various future monitoring systems. The ...
1994-07-17
Information technology resources assessment
Energy Technology Data Exchange (ETDEWEB)
This year's Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible ...
1992-01-01
Information technology resources assessment
Energy Technology Data Exchange (ETDEWEB)
This year`s Information Technology Resources Assessment (ITRA) is something of a departure from traditional practice. Past assessments have concentrated on developments in fundamental technology, particularly with respect to hardware. They form an impressive chronicle of decreasing cycle times, increasing densities, decreasing costs (or, equivalently, increasing capacity and capability per dollar spent), and new system architectures, with a leavening of operating systems and languages. Past assessments have aimed -- and succeeded -- at putting information technology squarely in the spotlight; by contrast, in the first part of this assessment, we would like to move it to the background, and encourage the reader to reflect less on the continuing technological miracles of miniaturization in space and time and more on the second- and third-order implications of some possible workplace ...
1992-01-01
The U.S. Liquid Metal Reactor Development Program
International Nuclear Information System (INIS)
This paper discusses how the U.S. Liquid Metal Reactor Development Program has been restructured to carry out R and D on advanced reactor technology. The program gives particular emphasis to improvements to reactor safety. The new directions are based on the technology of the integral fast reactor (IFR). Much of the basis for superior safety performance using IFR technology has been experimentally verified and aggressive programs continue in EBR-II and TREAT. Progress has been made in demonstrating both the metallic fuel and the new electrochemical processes of the IFR. The FFTF facility is converting to metallic fuel; however, FFTF also maintains a considerable U.S. program in oxide fuels. In addition, generic programs are continuing in steam generator testing, materials development, and with international cooperation, aqueous reprocessing.
1988-05-01
Abstracts: Eighth Annual Conference on Fossil Energy Materials. Fossil Energy Program
Energy Technology Data Exchange (ETDEWEB)
Abstracts are presented for about 40 papers. The Fossil Energy Advanced Research and Technology Development Materials program is an integrated materials research activity of the fossil energy coal program, whose objective is to conduct R and D for all advanced coal conversion and utilization technologies. The program is aimed at understanding materials behavior in coal system environments and the development of new materials for improving plant operations and reliability. A generic approach is used for addressing multiple coal technologies; for example, the hot-gas particulate filter development is applicable to pressurized fluidized bed combustion, integrated coal gasification combined-cycle, coal combustion, and indirectly fired combined-cycle systems.
1994-07-01
Upgraded coal interest group. Quarterly report, July 1, 1995--September 30, 1995
Energy Technology Data Exchange (ETDEWEB)
The objectives of the Upgraded Coal Interest Group (UCIG) are as follows: Review and update the status of various coal upgrading technologies and developments and critically assess the results. Perform engineering screening analyses on various coal upgrading approaches. Perform commercialization analyses that will promote the availability and use of upgraded coal products by quantifying the benefits of using them. Identify market opportunities for introduction of upgraded coals. Perform critical analyses on a variety of coals and technologies in areas important to users but not readily available. Perform critical experiments which will show the differences between technologies.
1995-12-31
Energy Technology Data Exchange (ETDEWEB)
The objective of this work is a study for the application of a new technology that will be used in the engine management system in the vehicle; where the final consumer can opt for the inquiry performance or seeking an economy for the fuel consumption depending on its daily use and of the prices offered in the gas stations. Flexible Fuel is a technology in development for the automobile market that mixes the use of two fuels (gasoline and ethanol) and their mixtures in the internal combustion engine. (author)
2006-07-01
Review of the Vortec soil remediation demonstration program
Energy Technology Data Exchange (ETDEWEB)
The DOE`s clean-up of its nuclear complex require the development of innovative technologies to convert soils contaminated by hazardous and/or radioactive wastes to forms which can be readily disposed in accordance with current waste disposal methods. The unique features of Votec CMS technology should make it particularly cost-effective process for the vitrification of soils, sediments, sludges, and mill tailings containing organic metallic and/or radioactive contaminants. This article describes the technology (Votec`s combustion and melting system), the results of testing, the demonstration plant system, and summarizes the future schedule and the equipment needed. 3 figs., 3 tabs.
1994-11-01
Report of study group 7.1: natural gas in competition with electric power in industrial applications
Energy Technology Data Exchange (ETDEWEB)
This report consists of three sections. The first section is a brief general overview of all the issues that impact the competition between natural gas and electricity in industrial applications. The second section of this report focus on the all the marketing issues and provides detail analysis of the status of these issues in Europe, Japan and United States. The third section of this report is a detail review of the current status of the competition between gas technologies and electro-technologies, it also make recommendation for developing new gas technologies. The fourth section is a contribution from M. Pettersson and S. Stenstroem, Sweden, on infrared dryers. (authors)
2000-07-01
Removal of uranium by biosorption
Energy Technology Data Exchange (ETDEWEB)
The technology developed here will exploit the ability of microorganisms to remove dissolved metals from aqueous solutions. Microbial sorbents for uranium will be immobilized biosorbents will be deployed ex situ within flow-through reactors for the continuous or semicontinuous treatment of recovered wastewaters. The proposed technology will primarily be applied within a pump-and-treat process using immobilized biosorbents for the large-scale, long-term remediation of uranium-laden surface water or groundwater impoundments (environmental restoration). The technology may be equally useful as an ``end-of-pipe`` treatment of process effluents (waste management). Successful operation of this process will achieve immobilization of the targeted waste and accompanying volume reduction.
1993-06-01
Energy Technology Data Exchange (ETDEWEB)
This paper presents a survey on public preferences in SE England for the use of wind, biomass and nuclear power in electricity generation. Using a labelled CE the perceived importance (value) to the public of distance and the energy options' impacts on biodiversity, emissions, land occupation and household cost was explored. Results suggest that impacts, technology name, demographic characteristics, attitudes towards the environment, knowledge and experience with the technologies were significant choice determinants. Considering the current debate about the development of nuclear power and biomass in UK and worldwide, this survey provides an insight into the factors affecting public acceptability
2008-07-01
Japanese R&D on new cast alloys and materials
Energy Technology Data Exchange (ETDEWEB)
On the basis of observations of the JTEC team, it appears that Japanese universities and research institutes are leading long-term R&D thrusts for development of new materials casting technologies. Significant efforts include amorphous metals, intermetallics, application of MHD in continuous casting of steel, and energy efficient furnace technology. Industrial R&D seems focused more on process improvements than on new product technologies, but significant efforts in new cast materials included cast metal matrix composites, materials substitutions for thinner wall products, and advanced ceramic products for foundry industry applications.
1996-05-01
Geothermal well cost sensitivity analysis: current status
Energy Technology Data Exchange (ETDEWEB)
The geothermal well-cost model developed by Sandia National Laboratories is being used to analyze the sensitivity of well costs to improvements in geothermal drilling technology. Three interim results from this modeling effort are discussed. The sensitivity of well costs to bit parameters, rig parameters, and material costs; an analysis of the cost reduction potential of an advanced bit; and a consideration of breakeven costs for new cementing technology. All three results illustrate that the well-cost savings arising from any new technology will be highly site-dependent but that in specific wells the advances considered can result in significant cost reductions.
1980-01-01
Final report [Homes Tours and Green Building Program Development
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy Office of Building Technology, State and Community Programs sponsored EcoTecture Solutions, Inc. (dba Sustainable Living Alliance {trademark}) in producing two home tours showcasing energy- and resource-efficient buildings in Austin, Texas, held on October 16, 1999, and Albuquerque, New Mexico, held on May 20, 2000. Lists are given of the notable building technologies, passive solar design features, and energy- and water-efficient technologies and design employed in the houses. There were over 1200 visitors to the 22 residential and 3 commercial buildings included in the tour.
2000-06-28
Energy Technology Data Exchange (ETDEWEB)
The state of the laboratory address by LLNL Director Roger Batzel is summarized, and a breakdown of the laboratory funding is given. The Livermore defense-related committment is described, including the design and development of advanced nuclear weapons as well as research in inertial confinement fusion, nonnuclear ordnance, and particle beam technology. LLNL is also applying its scientific and engineering resources to the dual challenge of meeting future energy needs without degrading the quality of the biosphere. Some representative examples are given of the supporting groups vital for providing the specialized expertise and new technologies required by the laboratory's major research programs. (GHT)
1982-07-01
Energy Technology Data Exchange (ETDEWEB)
The overall goal of the Coal Liquefaction Program of the Office of Coal Technology (OCT) is to develop the scientific and engineering knowledge base with which industry can bring economically competitive and environmentally acceptable advanced technology for manufacturing synthetic liquid fuels from coal into the marketplace when needed. The technical goal of the Coal Liquefaction Program is to seek advanced and innovative improvements over the state-of-the-art processes for coal liquefaction that can utilize all major parts of the US coal resource base. A technology description and discussion of program goals and strategy is provided in this report. 2 figs.
1989-09-01
Centre for Quantum Computation & Communication Technology
This is the homepage of "an Australian multi-university collaboration undertaking research on the fundamental physics and technology of building, at the atomic level, a solid state quantum computer in silicon together with other high potential implementations." Although attempts to develop a quantum computer have met with limited success, the centre has substantial resources invested in advancing toward practical uses of quantum computing technology. The site provides a very good introduction to the principles and implications of quantum computing, as well as details about various research projects underway at the Australian universities. Links to conference and journal papers produced by members of the centre, many from 2003, are also provided.
Getting America Ready for Japanese Science and Technology.
The proceedings of a conference on the development of language capabilities to prepare United States scientists to share in scientific and technological development with Japan include these papers: "Are Japanese Language Programs Reaching Scientists and Engineers?"; "Japanese Language Study for Engineers: High Tech Perspectives"; "Applied Japanese Studies for Science and Engineering at American Universities"; "Training and Certifying Japanese Technical Translators"; "Designing Effective Language Teaching for Professionals"; "Problems in Teaching Technical Japanese"; "Commentary" A Cautious and Deliberate Strategy Is Needed"; "Establishing a Japanese High-Technology Information Company in the United States"; "The Problems of Operating a Technical Translation Company in Japan";"The Japan Information Center of Science and Technology"; "A National Agenda for Japanese Language Training"; ...
1985-05-15
Assisted reproductive technologies for male factor infertility.
Experience in the diagnosis and treatment of infertility has led to an increased understanding of the prominent role male factors play in many couples' inability to conceive. While many forms of male factor infertility are amenable to treatment, for some patients there is no corrective therapy available. For this reason, a great deal of attention has been focused on developing technologies for semen processing and sperm utilization in cases of decreased semen quality. One area of research is the development of more sophisticated methods of assessing sperm function, as well as methods of sperm preparation. Progress is also being made in the application of technologies such as intrauterine insemination and in vitro fertilization in the treatment of male factor infertility. Such developments have improved prospects for fertility among patients suffering from decreased semen quality, as ...
1991-10-01
Government policy and the development of electric vehicles in Japan
International Nuclear Information System (INIS)
The aim of this paper is to analyse the role that the Japanese Government has played in the development of alternatives to conventional vehicles, the effect of government programmes, and the importance of technical flexibility in government support schemes. The focus is on battery-powered electric vehicles (BPEVs), hybrid electric vehicles (HEVs), and fuel cell electric vehicles. The effects of government policy and the process of innovation are analysed from a systems approach drawing on the literature regarding technical change and innovation. The whole chain of government support, including the context in which these different policies have been implemented since the early 1970s, is studied. The Japanese Government has adopted a comprehensive strategy including R and D, demonstration programmes and market support guided by long-term strategic plans. The role of the Government has been that of a conductor in the development process supplying ...
2006-03-01
Energy Technology Data Exchange (ETDEWEB)
Man's wastes are polluting the oceans from various sources and delivered by various routes. The result has been the loss of habitat and the irreversible altering of marine ecosystems. Development in the coastal zones and offshore activities that disrupt biologically sensitive areas have led to international negotiations to regulate these impacts and develop a law of the sea. Basic to international cooperation, however, is the need to develop answers to questions about the ecological consequences of development programs and the carrying capacity of the oceans. Current information does not demonstrate long-term global impacts, making it difficult to detect and predict incremental changes and causal relationships. Society needs to determine how much environmental damage it will accept and then to develop appropriate technology, such as biomonitoring. ...
1981-03-01
The summarize of the technique about proactive network security protection
International Nuclear Information System (INIS)
The proactive protection measures and the traditional passive security protection tools are complementarities each other. It also can supply the conventional network security protection system and enhance its capability of the security protection. Based upon sorts of existing network security technologies, this article analyses and summarizes the technologies, functions and the development directions of some key proactive network security protection tools. (authors)
2003-09-08
Tehachapi solar thermal system first annual report
Energy Technology Data Exchange (ETDEWEB)
The staff of the Southwest Technology Development Institute (SWTDI), in conjunction with the staff of Industrial Solar Technology (IST), have analyzed the performance, operation, and maintenance of a large solar process heat system in use at the 5,000 inmate California Correctional Institution (CCI) in Tehachapi, CA. This report summarizes the key design features of the solar plant, its construction and maintenance histories through the end of 1991, and the performance data collected at the plant by a dedicated on-site data acquisition system (DAS).
1993-05-01
... Targeted fields of research Continuation of ongoing research - Finalising detailed design work on the ITER project; getting JET operational at full power; Improvement of the basic concepts of fusion devices - Fusion plasmas; theoretical studies; technology watch on research into inertial confinement; new experimental concepts and systems; etc.; Long-term technology - Preparations for building a demonstration reactor (development of tritium breeding blankets; prospective ...
Quality assurance requirements for nuclear power plants in Hungary
International Nuclear Information System (INIS)
In Hungary, legislation for nuclear power plants was developed at the end of the 1970s, among which is the quality assurance code for nuclear power plants. Hungarian practice is presented, including discussion of the requirements for quality assurance, qualification of the suppliers and inspection practices. The general requirements of quality assurance in the course of construction of a nuclear power plant are presented: quality assurance of technological equipment, fuel, electrical equipment, automatic instrumentations, building structures and technology.
Photovoltaics: Program overview, fiscal year 1992
Energy Technology Data Exchange (ETDEWEB)
The US DOE`s Photovoltaics program has helped photovoltaic technologies evolve from materials and concepts in the laboratories to competitive products rolling off automated assembly lines. This document is divided into the following sections: 1992 PV program accomplishments, expanding markets for photovoltaic systems, developing today`s systems with utilities and industry, working with industry to advance the technology, cooperative research to improve materials and devices, selected achievements in cooperative R and D, and PV program services. Figs, tabs.
1993-03-01
Phosphors for flat panel emissive displays
Energy Technology Data Exchange (ETDEWEB)
An overview of emissive display technologies is presented. Display types briefly described include: cathode ray tubes (CRTs), field emission displays (FEDs), electroluminescent displays (ELDs), and plasma display panels (PDPs). The critical role of phosphors in further development of the latter three flat panel emissive display technologies is outlined. The need for stable, efficient red, green, and blue phosphors for RGB fall color displays is emphasized.
1995-07-01
Industrial ecology at Lawrence Livermore National Laboratory summary statement
Energy Technology Data Exchange (ETDEWEB)
This statement summarizes Lawrence Livermore National Laboratory`s committment to making important scientific, technological, and business contributions to global sustainability. The quest has many aspects, some socio-political or economic and some technological, and some in which the soft and hard sciences become indistinguishable, as in visionary national strategies, like Holland`s, and futuristic regional and city development plans, like those of Kagoshima and Chattanooga.
1996-05-21
Development of technical information basis of aging management for nuclear power plants
International Nuclear Information System (INIS)
In order to implement effective safety regulations on aging management for reactor facilities etc., the information on important technology issues, the latest technical knowledge including evaluation technology, test and research outcomes, related codes and standards, regulation information, operation experiences such as accidents and trouble, etc. with respect to aging-induced deterioration in and outside Japan and in other industries, were collected, organized and evaluated. (author)
2007-08-01
This document provides a technical basis for the revision of chemical effluent limitations guidelines for the Steam Electric Power Industry reflecting the Best Available Technology Economically Achievable (BATEA) for existing sources, New Source Performance Standards (NSPS) and Pretreatment Standards. The analysis of pollutants and the technologies applicable to their control has been based on specific waste streams of concern.
1980-09-01
Annotated bibliography of Accelerator Technology Division research and development, 1978-1985
International Nuclear Information System (INIS)
A bibliography is presented of unclassified published and in-house technical material written by members of the Accelerator Technology Division, Los Alamos National Laboratory, since its inception in January, 1978. The author and subject concordances in this report provide cross-reference to detailed citations kept in a computer database and a microfilm file of the documents. The citations include an abstract and other notes, and can be searched for key words and phrases.
A management scheme for reducing pollution at air discharge facility in advance
Energy Technology Data Exchange (ETDEWEB)
The developed countries are implementing a policy minimizing damage from environmental pollution by reducing discharge in advance as well as the aftermath of a pollutant. The typical example is to use BAT (Best Available Technology). This is to prevent environmental damage by reducing the discharge of pollutants with available technology and to secure environmental margin to enable industrial activities of future generation. Therefore, the feasibility of introducing BAT requirement system was reviewed by considering foreign examples and Korean situation. 38 refs., 8 figs., 69 tabs.
1998-12-01
Energy Technology Data Exchange (ETDEWEB)
The U.S. Department of Energy (DOE) and the U.S. Council for Automotive Research (composed of automakers Ford, General Motors, and Chrysler) announced in January 2002 a new cooperative research effort. Known as 'FreedomCAR' (derived from 'Freedom' and 'Cooperative Automotive Research'), it represents DOE's commitment to developing public/private partnerships to fund high-risk, high-payoff research into advanced automotive technologies. Efficient fuel cell technology, which uses hydrogen to power automobiles without air pollution, is a very promising pathway to achieving the ultimate vision. The new partnership replaces and builds upon the Partnership for a New Generation of Vehicles initiative that ran from 1993 through 2001. The Advanced Power Electronics and Electric Machines (APEEM) subprogram within the FreedomCAR and Vehicle ...
2007-10-01
Biotechnology developments in the livestock sector in developing countries.
Global meat and milk consumption is exponentially increasing due to population growth, urbanization and changes in lifestyle in the developing world. This is an excellent opportunity for developing countries to improve the livestock sector by using technological advances. Biotechnology is one of the avenues for improved production in the "Livestock revolution". Biotechnology developments applied to livestock health, nutrition, breeding and reproduction are improving with a reasonable pace in developing countries. Simple bio-techniques such as artificial insemination have been well implemented in many parts of the developing world. However, advanced technologies including transgenic plant vaccines, marker assisted selection, solid state fermentation for the production of fibrolytic enzymes, transgenic fodders, embryo transfer and animal ...
2010-01-01
Recent Korean R&D in Satellite Communications
The R&D in satellite communications in Korea has been driven mainly by KCC (Korea Communications Commission) but in a small scale compared to Korea space development program organized by MEST (Ministry of Education, Science and Technology). Public and civilian satcom sector R&D has been led mainly by ETRI with small/medium companies contrary to rare investment in private sector while military sector R&D has been orchestrated by ADD with defense industry. By the COMS (Communication, Ocean and Meteorological Satellite) experimental Ka-band payload, Korea pursues a space qualification of own technology for national infrastructure evolution as well as industrialization of space R&D results. Once COMS launched and space qualified in 2009, subsequent application experiments and new technology R&D like UHDTV will entail service and industry promotion. The payload ...
2009-01-01
The paper discusses recent work on lime enhancement and testing at the bench-scale, followed by evaluation of the more promising sorbents in a pilot plant to develop low cost, retrofittable flue gas cleaning technology specifically the development of highly reactive sorbents. Con...
Universal Camouflage for the Future Warrior.
Due to increased deployments with varied missions and new technologies/advanced threats against U.S. Soldiers, a clear need arose for developing camouflage pattern(s) to enhance the Warfighter's survivability' on the modern battlefield. Based on these tec...
2004-01-01
Understanding the nature of the statistics behind energy-related CO{sub 2} emissions
Energy Technology Data Exchange (ETDEWEB)
Research reported here reveals that the reduction of CO{sub 2} emissions into the atmosphere, is mainly dependent on the decrease of the use of fossil fuels, but also on the development of environment-friendly technology and greening of the environment. 2 refs.
2001-07-01
Transposon-based screens for cancer gene discovery in mouse models
UK PubMed Central (United Kingdom)
Significant emphasis has recently been placed on the characterization of the human cancer genome. This effort has been assisted by the development of new DNA sequencing technologies that allow...Full Text Available
2010-08-01
The physics of automatic letter sorting
The astronomical number of letters handled by the Post Office makes automatic sorting technology essential. Key roles are played by the postcode system and an ink-jet printer that has been developed to use phosphorescent inks.
1988-07-01
Energy Technology Data Exchange (ETDEWEB)
The Danish windmill industry has become an international success. This book describes the historical development of the Danish windmill industry and technology and evaluates the innovation ability of these. (LG) 176 ref.
1991-01-01
UK PubMed Central (United Kingdom)
BackgroundWith a growing number of genetic tests becoming available to the health and consumer markets, genetic health care providers in Canada are faced with the challenge of developing...Full Text Available
Robust parameter extraction for decision support using multimodal intensive care data
UK PubMed Central (United Kingdom)
Digital information flow within the intensive care unit (ICU) continues to grow, with advances in technology and computational biology. Recent developments in the integration and archiving of these...Full Text Available
2009-01-28
NASA needed a way to safely strip old paint and thermal protection material from reusable components from the Space Shuttle; to meet this requirement, Marshall Space Flight Center teamed with United Technologies' USBI Company and developed a stripping sys...
1996-01-01
Phytoremediation of Soil Trace Elements
This chapter summarizes research progress in development of phytoremediation technologies. Some soils have become contaminated by trace elements enough to kill plants, inhibit soil organisms, and/or threaten wildlife, humans or the environment. Traditional remediation by dig and haul methods are v...
Energy Technology Data Exchange (ETDEWEB)
The Oil Shale Program is directed toward the development of advanced technologies for extracting shale oil from large, currently unrecoverable oil shale resources. The overall goal of the Oil Shale Program is to foster development by the private sector of an economically competitive and environmentally acceptable oil shale industry whose products can compete with natural petroleum liquids in the marketplace by the year 2000. For the achievement of this goal, a series of interrelated technology development steps must take place, some sponsored by DOE, some by other government agencies, and some by other governments and/or the private sector. These include basic and applied research and development, proof-of-concept activities, first-of-a-kind field tests, and associated commercial scale activity. Activities associated with the Oil Shale Program are designed to ...
1986-03-01
UK PubMed Central (United Kingdom)
Background The scale-up of treatment for HIV and multidrug-resistant tuberculosis (MDR-TB) in developing countries requires a long-term relationship with the...Full Text Available
The National Cancer Institute Laboratory of Human Carcinogenesis is seeking statements of capability or interest from parties interested in collaborative research to further develop, evaluate, or commercialize a gene signature for prognosis of hepatocellular carcinoma in patients.
Energy Technology Data Exchange (ETDEWEB)
The motivation, feasibility and potential for two unconventional collider concepts - the Gamma-Gamma Collider and the Muon Collider - are described. The importance of the development of associated technologies such as high average power, high repetition rate lasers and ultrafast phase-space techniques are outlined.
1994-11-01
Epitope tagging of endogenous proteins for genome wide Chromatin immunoprecipitation analysis
UK PubMed Central (United Kingdom)
The development of chromatin immunoprecipitation methods coupled with DNA microarray (ChIP-chip) technology has enabled genome-wide identification of cis-DNA regulatory elements to which transcription...Full Text Available
2009-01-01
Eddy Current Inspection of Mildly Ferromagnetic Tubing.
The past decade has seen the development of eddy current probes for inspection of the mildly ferro-magnetic alloy Monel 400. Due to the rapid advances in permanent magnet technology similar probes have been upgraded to magnetically saturate, and hence ins...
1984-01-01
Digital Talking Books: Planning for the Future.
Ever-changing audio technology requires that National Library Service NLS always be aware of developments and prepare carefully for any systematic changes that may be desired or required. Usefulness, cost effectiveness, thoughtful stewardship, and educate...
1998-01-01
Development on the technology for tritium removal processes (II).
In order to decrease tritium exposure to workers, the ratio of which is up to 40% of total exposure, tritium removal facility is getting to be one of the considerable parameters in Korea, due to the next CANDUs to be operated at Wolsung NPP. For investiga...
1993-01-01
Development on the core technologies for tritium removal processes (I).
At Wolsung NPP, three more CANDU reactors will be operated soon, and the tritium accumulation in the moderator and coolant systems was estimated to be greatly increased. In order to reduce tritium exposure for nuclear safety at Wolsung, a study was carrie...
1993-01-01
Development of a technology for coal conversion in the presence of coal tar
British Library Electronic Table of Contents (United Kingdom)
A new process for the hydrogenation of coal in the presence of wide-cut coal tar was proposed; it involves cavitation treatment, mixing with catalytic additives, and heating the resulting mixture at an elevated pressure in an atmosphere of hydrogen. The yields of hydrocarbon fractions to 300?C and gas condensate were evaluated.
2011-01-01
Development of Tritium Removal Technology.
Liquid Phase Catalytic Exchange (LPCE)- Cryogenic Distillation(CD) process was studied which could be available for an optimal tritium removal process of pressurized heavy water reactor system at Wolsung nuclear power plant in the near future. Based upon ...
1986-01-01
Energy Technology Data Exchange (ETDEWEB)
Cited are the results of physico-chemical studies and industrial tests of a copolymer of methacrylic acid and diethylammonium salt, used for limiting the influx of stratum waters into a well.
1981-01-01
UK PubMed Central (United Kingdom)
This article presents a study identifying benefits and challenges of a novel hospital-to-hospital information technology (IT) outsourcing partnership (HHP). The partnership is an innovative response...Full Text Available
2008-07-01
Cooperative research in coal liquefaction infratechnology and generic technology development
Energy Technology Data Exchange (ETDEWEB)
Cooperative research in coal liquefaction from Auburn University, University of Kentucky, University of Pittsburgh, West Virginia University, University of Utah, and the UK Center for Applied Energy Research, are briefly discussed. Topics covered include desulfurization, chemical reactivity, coprocessing, and catalysis. (CBS)
1989-01-01
Combustible cartridge cases are at present produced either by the beater additive or by the post impregnation process. The literature covering these techniques, which basically follow the concept of fibre moulding and/or papermaking, is reviewed. The vari...
1986-01-01
Citrate Process for Flue Gas Desulfurization.
As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pct SO2...
1986-01-01
Ceramics Thermosynthesis in Combustion Wave
International Science & Technology Center (ISTC)
Development of New Resource-Saving Technologies for Ceramic Material Production: High resistant Pigments, Heat Shielding, Plasters, Filters, etc.; by the Method of Controllable Thermosynthesis in Combustion Wave Using Industrial Metal-Containing Wastes
BUBL LINK: Library organisations
...6 Resource type: documents MmIT: Multimedia Information and Technology Group Group aiming to facilitate communication between CILIP members interested in multimedia developments in the library and information science field. Visits to places of interest like museums and archives are frequently organised, and an email discussion list ...
Energy Technology Data Exchange (ETDEWEB)
This research and development is intended to structure a network centering around a center having systematized high-level maintenance technology, by utilizing the technological infrastructure having been built in local areas, together with element technologies possessed by national and private research institutes, universities and colleges. It is also purposed to establish a new industrial system for maintenance to realize high reliability, high operation rate and low cost in plants in certain areas. The present fiscal year had the following achievements: research and development of a maintenance system, a maintenance model, a maintenance vehicle, damage estimating technology for stationary parts such as piping, an anomaly diagnostic system using acoustic emission, an anomaly diagnostic system using wear particles in lubricant, an anti-wear material using ...
1999-03-01
A Computerized Hospital to Physician Office Link Based on Readily Available Technology
UK PubMed Central (United Kingdom)
Most hospitals today are quickly developing special programs and services that are designed to compete for physicians and patients, and ultimately fill unoccupied beds. In an attempt to attract physicians...Full Text Available
1989-11-08
20th century and radiation accidents; O seculo XX e os acidentes nucleares
Energy Technology Data Exchange (ETDEWEB)
The chapter presents the nuclear energy development in 20th century and the most important radiation accidents happened from the point of view of technological risk and high impact consequences: Three Mile Island and Chernobyl.
2006-07-01
Energy Technology Data Exchange (ETDEWEB)
The conference was organized to bring together scientific and business people from Canada, United States, and Mexico to foster the protection and improvement of the environment and to promote sustainable development in the three NAFTA countries. The sessions are international cooperation and partnerships (panel discussion), markets, market access, economic instruments, venture and capital growth, economic instruments versus regulations, international financial institutions, partnerships and networks, government support programs (panel), acid rain, stratospheric ozone, smog and ground level ozone, innovative measurement methods, hazardous air pollutants, respirable fine particulates, climate change prevention technologies, pollution prevention technologies, indoor air technology, and posters. Selected papers have been abstracted separately.
1994-09-01
Surgical navigation using audio feedback.
Current medical visualization technology intended for positional guidance in surgical applications may only ever have limited utility in the operating room due to the preexisting visual requirements of surgical practice. Additionally, visual systems impose limits as a result of their high latency, poor image resolution, problems with stereopsis and physical strain upon the user. Audio technology is relatively unexamined in the broad range of available methodologies for medical devices. The potential to translate surgical instrument position into audio feedback presents a novel solution to the human factors and engineering problems faced by visual display technology because audio technology employs a rich and as yet unburdened sensory modality. We describe an experimental system we have developed for investigating this new interface design approach using commercially available ...
1997-01-01
Energy Technology Data Exchange (ETDEWEB)
A compilation of technical papers, from the 23rd annual Precise Time and Time Interval (PTTI) Applications and Planning Meeting, is presented. Papers were given in the following categories: (1) developments in rubidium, cesium, and hydrogen-based frequency standards, and in cryogenic and trapped-ion technology; (2) international and transnational applications of PTTI technology with emphasis on satellite laser tracking networks, GLONASS timing, comparison of national time scales and international communications; (3) applications of PTTI technology to the telecommunications, power distribution, platform positioning, and geophysical survey industries; (4) applications of PTTI technology to evolving military communications and navigation systems; and (5) dissemination of precise time and frequency by means of GPS, GLONASS, MILSTAR, Loran, and synchronous communications satellites.
1992-07-01
New technology for purging the steam generators of nuclear power plants
British Library Electronic Table of Contents (United Kingdom)
A technology for removal of undissolved impurities from a horizontal steam generator using purge water is developed on the basis of a theoretical analysis. A purge with a maximal flow rate is drawn off from the zone with the highest accumulation of sludge in the lower part of the steam generator after the main circulation pump of the corresponding loop is shut off and the temperatures of the heat transfer medium at the inlet and outlet of the steam generator have equilibrated. An improved purge configuration is used for this technology; it employs shutoff and regulator valves, periodic purge lines separated by a cutoff fixture, and a D y 100 drain union as a connector for the periodic purge. Field tests show that the efficiency of this technology for sludge removal by purge water is severa...
2011-01-01
International Nuclear Information System (INIS)
The IGC Highlights briefly outlines some of the the significant progresses made by Indira Gandhi Centre for Atomic Research, Kalpakkam during the period 1996-1997. The Fast Breeder Test Reactor (FBTR) was operated at the maximum power level possible with the available partial core. The first generation of electricity from FBTR and its synchronization with the grid in 1997 marked a significant step in the nuclear programme of the Centre. Another important event was the commissioning of the "2"3"3U - fuelled Kamini reactor.The mission-oriented programmes in fast reactor technology was supported by a host of research and development programmes, in closely related areas namely materials technology, welding metallurgy, sodium technology, manufacturing technology, non-destructive testing, quality engineering, in-service inspection, electronics and instrumentation and safety research. The ...
The basic metal industry and its energy use. Prospects for the Dutch energy intensive industry
Energy Technology Data Exchange (ETDEWEB)
This report discusses the current state and the future of the Dutch basic metal industry. The steel industry and the aluminium industry are discussed in detail. First their current energy use, the technology and their product markets are analysed. The competitiveness of Dutch and Western European producers is discussed. Main technological developments and other key issues (especially future CO2 policies) are analysed. Based on this analysis, scenarios are developed for the energy use in the basic metal industry for the period 2000-2020. 88 tabs., 55 figs., 143 refs.
1997-03-01
Energy Technology Data Exchange (ETDEWEB)
By setting up a fully indicated, modern passenger car diesel engine, Mahle has created the basis for systematically testing current and future engine technologies. The experimental set-up has both an integrated high- and low-pressure EGR circuit and an open engine control unit, thus enabling efficient development of new systems under real-world conditions. The advantages of this comprehensive approach are illustrated below, using the example of different EGR technologies tested. (orig.)
2010-10-15
Energy Technology Data Exchange (ETDEWEB)
Due to the general market conditions, the construction of steam turbines was greatly reduced in 1987. As in 1986, it came to a downward movement. This situation will heighten in the coming years. The exploitation of devices, which are available by way of the development of EDP in computation, construction, production and operation, leads to considerable improvements. These improvements can only be employed gradually, due to the reduction in production. However, technological progress can be used economically in part in the restoration of old installations. Here turbine construction, the thermodynamical interpretation of gas and steam turbines, developments in the field of conduction technology, piping and materials are described. Also improvements in operation security and operation supervision of the installations is treated, as well as service and maintenance of the plants. (BR) With 131 refs.
1988-04-01
International Nuclear Information System (INIS)
The following Resolution has been stated because of the results of the workshops Elaboration of proposals for strategic guidelines held from 2 to May 5, 2006, elaboration of proposals for the Strategic Lines instruments held from 24 to July 28, 2006, as well as documents Proposal of politic energetic Uruguayan Energy Sector development and proposal of Energy Policy Instruments developed by the National Directorate of Nuclear Energy and Technology and the Energy Strategy Guidelines Uruguay 2006.
2006-10-12
INEEL Advanced Radiotherapy Research Program Annual Report 2001
Energy Technology Data Exchange (ETDEWEB)
This report summarizes the major activities and accomplishments of the Idaho National Engineering and Environmental Laboratory (INEEL) Advanced Radiotherapy Research Program for calendar year 2001. Applications of supportive research and development, as well as technology deployment in the fields of chemistry, radiation physics and dosimetry, and neutron source design and demonstration are described. Contributions in the fields of physics and biophysics include development of advanced patient treatment planning software, feasibility studies of accelerator neutron source technology for Neutron Capture Therapy (NCT), and completion of major modifications to the research reactor at Washington State University to produce an epithermal-neutron beam for NCT research applications.
2002-04-01
INEEL Advanced Radiotherapy Research Program Annual Report 2001
Energy Technology Data Exchange (ETDEWEB)
This report summarizes the major activities and accomplishments of the Idaho National Engineering and Environmental Laboratory (INEEL) Advanced Radiotherapy Research Program for calendar year 2001. Applications of supportive research and development, as well as technology deployment in the fields of chemistry, radiation physics and dosimetry, and neutron source design and demonstration are described. Contributions in the fields of physics and biophysics include development of advanced patient treatment planning software, feasibility studies of accelerator neutron source technology for Neutron Capture Therapy (NCT), and completion of major modifications to the research reactor at Washington State University to produce an epithermal-neutron beam for NCT research applications.
2002-04-30
Free electron radiation and the Beijing Free Electron Laser
International Nuclear Information System (INIS)
Various particle-photon or beam-wave interactions are discussed. To be of use as intense radiation sources, it is necessary that these interactions produce coherent radiation. The free electron laser (FEL), developed on the basis of undulator radiation, is the result of many years of interaction between physics and technology. It has many features, such as continuous tunability over a wide wavelength range, excellent optical quality, high power and short pulse capability, and thus has many potential applications. FEL development in China and abroad are mentioned and the Beijing FEL presented to illustrate the physics and technology involved in an FEL project.
Electric and Hybrid Vehicles Program. Sixteenth annual report to Congress for fiscal year 1992
Energy Technology Data Exchange (ETDEWEB)
This report describes the progress achieved in developing electric and hybrid vehicle technologies, beginning with highlights of recent accomplishments in FY 1992. Detailed descriptions are provided of program activities during FY 1992 in the areas of battery, fuel cell, and propulsion system development, and testing and evaluation of new technology in fleet site operations and in laboratories. This Annual Report also contains a status report on incentives and use of foreign components, as well as a list of publications resulting from the DOE program.
1993-08-01
Development of flue gas carbon dioxide recovery technology
Energy Technology Data Exchange (ETDEWEB)
As a counter measure to protect against global warming, the development of CO{sub 2} recovery technology from fossil fuel power plant flue gas has continued. MEA processes are widely used for CO{sub 2} recovery from combustion flue gas in average use etc. However, if we consider power plant scale CO{sub 2} recovery, the biggest theme is the reduction of energy needed to recover CO{sub 2}. The paper focuses on sterically hindered amines and a new absorber packing. Also optimum steam system analysis results are indicated. 1 ref., 16 figs., 3 tabs.
1994-12-31
Energy Technology Data Exchange (ETDEWEB)
Technical Development Document supporting proposed water discharge regulations for the Coal Mining Industry authorized by the Clean Water Act. Proposed regulations include revised best practicable technology limitations, best available technology limitations and new source performance standards for the Coal Mining Industry. Industry operations include: coal preparation and amillary operations, active mining, F bituminous, anthracite and lignite coal, and the reclamation phase of mining.
1981-01-01
Energy Technology Data Exchange (ETDEWEB)
This report describes the activities, conclusions, and recommendations of the Workshop on Evaluation Systems for Renewable Energy Systems sponsored by the Agency for International Development and SERI, held 20-22 February 1980 in Golden, Colorado. The primary objectives of the workshop was to explore whether it was possible to establish common information elements that would describe the operation and impact of renewable energy projects in developing countries. The workshop provided a forum for development program managers to discuss the information they would like to receive about renewable energy projects and to determine whether common data could be agreed on to facilitate information exchange among development organizations. Such information could be shared among institutions and used to make informed judyments on the economic, technical, and social feasibility of the ...
1980-06-01
Energy Technology Data Exchange (ETDEWEB)
For the purpose of digging up themes of the joint research which develop the R and D in the industrial technology field in Japan to a new stage, researchers were sent to the world representing research institutes to conduct the research survey of 'Nano-structured carbon and hydrogen absorption' and 'Development of the creation technology of nano-porous materials.' As to the former, an experiment on electrochemical hydrogen absorption of carbon materials including nanotubes was conducted by researchers dispatched, but the large absorption amount was not observed. As to the latter, visits were paid to Fraunhofer Institute and the related facilities in Germany, Princeton University, MIT, GIT and Naval Research Laboratories in the U.S., Orleans University in France, AO Research Institute (bone repair study) in Switzerland, Cambridge University and University of Bristol in ...
2001-03-01
Integrated thermal and nonthermal treatment technology and subsystem cost sensitivity analysis
Energy Technology Data Exchange (ETDEWEB)
The U.S. Department of Energy`s (DOE) Environmental Management Office of Science and Technology (EM-50) authorized studies on alternative systems for treating contact-handled DOE mixed low-level radioactive waste (MLLW). The on-going Integrated Thermal Treatment Systems` (ITTS) and the Integrated Nonthermal Treatment Systems` (INTS) studies satisfy this request. EM-50 further authorized supporting studies including this technology and subsystem cost sensitivity analysis. This analysis identifies areas where technology development could have the greatest impact on total life cycle system costs. These areas are determined by evaluating the sensitivity of system life cycle costs relative to changes in life cycle component or phase costs, subsystem costs, contingency allowance, facility capacity, operating life, and disposal costs. For all treatment systems, the most cost sensitive life cycle phase is the ...
1997-02-01
Geothermal energy technology: issues, R and D needs, and cooperative arrangements
Energy Technology Data Exchange (ETDEWEB)
In 1986, the National Research Council, through its Energy Engineering Board, formed the Committee on Geothermal Energy Technology. The committee's study addressed major issues in geothermal energy technology, made recommendations for research and development, and considered cooperative arrangements among government, industry, and universities to facilitate RandD under current severe budget constraints. The report addresses four types of geothermal energy: hydrothermal, geopressured, hot dry rock, and magma systems. Hydrothermal systems are the only type that are now economically competitive commercially. Further technology development by the Department of Energy could make the uneconomical hydrothermal resources commercially attractive to the industry. The economics are more uncertain for the longer-term technologies for extracting energy from ...
1987-01-01
Make Markets Work for Climate. Background Document
Energy Technology Data Exchange (ETDEWEB)
Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies ...
2006-07-01
Development of next-generation light water reactor in Japan
International Nuclear Information System (INIS)
In Japan, the development of next-generation Light Water Reactor has been launched since April 2008. The development program will be completed in 2015. The purpose of development is to cope with the replacement for existing nuclear power plants after 2030 in Japan and the expanding demand for nuclear power in the world; 'Nuclear Renaissance.' The reactor also aims to be global standard at around 2030. The requirements for global standard and domestic users have been investigated through the feasibility study of past 2 years, 2006-2007, and six innovative features or 'Core-Concepts' were established as follows. A) Reactor core system with uranium enrichment above 5% for significant decrease of spent fuel discharge and prominent higher availability B) Long-life materials and innovative water chemistry technologies for 80 years plant lifetime and significant reduction of occupational dose C) Seismic ...
2009-10-27
Remediation process technology for ground water
Energy Technology Data Exchange (ETDEWEB)
The operation of industrial facilities has generally resulted in contamination of the surrounding soils and ground water. A variety of methods have been proposed for the remediation of contaminated sites. This paper presents new process technology that is capable of performing treatment on ground water or soil washing leachates. The process is targeted to treat low levels of radioactivity, organics and heavy metals present in the aqueous solutions, to be easily transported and provide simple operation on-site and provide an effluent that meets the specified discharge quality. The purification process involves sequential chemical treatment and filtration. The paper will describe the development of the technology and review the current progress in its use to remediate contaminated sites at Chalk River. The application of the process technology has demonstrated that the ambitious goal of setting the ...
1993-12-31
Remediation process technology for ground water
International Nuclear Information System (INIS)
The operation of industrial facilities has generally resulted in contamination of the surrounding soils and ground water. A variety of methods have been proposed for the remediation of contaminated sites. This paper presents new process technology that is capable of performing treatment on ground water or soil washing leachates. The process is targeted to treat low levels of radioactivity, organics and heavy metals present in the aqueous solutions, to be easily transported and provide simple operation on-site and provide an effluent that meets the specified discharge quality. The purification process involves sequential chemical treatment and filtration. The paper will describe the development of the technology and review the current progress in its use to remediate contaminated sites at Chalk River. The application of the process technology has demonstrated that the ambitious goal of setting the ...
1993-09-05
Proceedings of the 1996 oil heat technology conference and workshop
Energy Technology Data Exchange (ETDEWEB)
This Conference is a key technology transfer activity supported by the ongoing Combustion Equipment Technology (Oil-Heat R and D) program at BNL, and is aimed at providing a forum for the exchange of information among international researchers, engineers, manufacturers, and marketers of oil-fired space-conditioning equipment. The objectives of the Conference were to: identify and evaluate the state-of-the-art and recommend new initiatives for higher efficiency, a cleaner environment, and to satisfy consumer needs cost-effectively, reliably, and safely; and foster cooperation among federal and industrial representatives with the common goal of sustained national economic growth and energy security via energy conservation. The 1996 Oil Technology Conference comprised: (a) fourteen technical papers, and (b) four workshops which focused on mainstream issues in oil-heating technology, namely: oilheat ...
1996-07-01
Energy Technology Data Exchange (ETDEWEB)
The purpose of this study is to evaluate the potential benefits of applying multiseam [well] completion (MSC) technology to the massive stack of low-rank coals in the Powder River Basin. As part of this, the study objectives are: Estimate how much additional CBM resource would become accessible and technically recoverable--compared to the current practice of drilling one well to drain a single coal seam; Determine whether there are economic benefits associated with MSC technology utilization (assuming its widespread, successful application) and if so, quantify the gains; Briefly examine why past attempts by Powder River Basin CBM operators to use MSC technology have been relatively unsuccessful; Provide the underpinnings to a decision whether a MSC technology development and/or demonstration effort is warranted by DOE. To a great extent, this assessment builds on the previously ...
2003-09-01
The goal of GRI's Gas Appliance Technology Center is to encourage the introduction of highly efficient, cost-effective, convenient gas appliances for residential and commercial gas users. The report covers activity at Battelle from February 1989 to April 1990 in broad support tasks, residential and commercial appliances, and residential space conditioning. Broad support tasks included the G/A/S Newsletter; the GATC InfoBase; and technology transfer, workshops, and GATC coordination. Residential appliance tasks included burner technology research, gas appliance venting, gas lighting, and plastics durability. Commercial appliance tasks included development of a commercial cooktop fuel/air mixing valve. Residential space conditioning tasks included a corrosion test method for gas appliances and vents, generic technology for condensing heat exchangers, and ...
1990-12-01
Energy Technology Data Exchange (ETDEWEB)
An innovative horizontal drilling system was used to install two horizontal wells as part of an integrated demonstration project at the Savannah River Site (SRS), Aiken, South Carolina. The SRS is located in south-central South Carolina in the upper Coastal Plain physiographic province. The demonstration site is located near the A/M Area, and is currently known as the Integated Demonstration Site. The Department of Energy's Office of Technology Development initiated an integrated demonstration of innovative technologies for cleanup of volatile organic compounds (VOCS) in soils and groundwater at the SRS in 1989. The overall goal of the program is to demonstrate, at a single location, multiple technologies in the fields of drilling, characterization, monitoring, and remediation. Innovative technologies are compared to one another and to baseline ...
1992-12-01
Energy Technology Data Exchange (ETDEWEB)
An innovative horizontal drilling system was used to install two horizontal wells as part of an integrated demonstration project at the Savannah River Site (SRS), Aiken, South Carolina. The SRS is located in south-central South Carolina in the upper Coastal Plain physiographic province. The demonstration site is located near the A/M Area, and is currently known as the Integated Demonstration Site. The Department of Energy`s Office of Technology Development initiated an integrated demonstration of innovative technologies for cleanup of volatile organic compounds (VOCS) in soils and groundwater at the SRS in 1989. The overall goal of the program is to demonstrate, at a single location, multiple technologies in the fields of drilling, characterization, monitoring, and remediation. Innovative technologies are compared to one another and to baseline technologies in ...
1992-12-01
Data summary of municipal solid waste management alternatives. Volume 2, Exhibits
Energy Technology Data Exchange (ETDEWEB)
The overall objective of the study in this report was to gather data on waste management technologies to allow comparison of various alternatives for managing municipal solid waste (MSW). The specific objectives of the study were to: 1. Compile detailed data for existing waste management technologies on costs, environmental releases, energy requirements and production, and coproducts such as recycled materials and compost. Identify missing information necessary to make energy, economic, and environmental comparisons of various MSW management technologies, and define needed research that could enhance the usefulness of the technology. 3. Develop a data base that can be used to identify the technology that best meets specific criteria defined by a user of the data base. Volume I contains the report text. Volume II contains supporting exhibits. Volumes III through ...
1992-10-01
The 'glass earth' - geochemical frontiers in exploration through cover
International Nuclear Information System (INIS)
'Glass Earth' represents a number of current and planned projects within CSIRO aimed at making 'transparent' the top 1000 m of the Earth's crust It builds upon current technologies developed within a number of CSIRO divisions as well as the Australian Mineral Exploration Technologies CRC (AMET CRC), the Australian Geodynamics CRC (AG CRC) and the CRC for Landscape Evolution and Mineral Exploration (CRC LEME). New geophysical and geochemical technologies will be developed to complement these, together with new capabilities in modelling, data integration and visualisation, including hydrogeochemistry, hydrogeology, surface geochemistry and isotope geochemistry, modelling of chemical, fluid and heat flows in rock and regolith, advanced visualisation and data fusion. This paper describes some recent work in the field of isotope geochemistry, with the principal aim of 'seeing through' ...
1999-09-24
International Nuclear Information System (INIS)
This paper reviews the state of the art of silicon-germanium technology and assesses the problems of building thermoelectric modules in Europe, based upon silicon-germanium alloys, for use in multihundred watt radio-isotope thermoelectric generator. The generator developed in the United States for the International Solar Polar mission has been used as a reference system. The essential features of an alternative system, which employs thermocouples fabricated from improved silicon-germanium alloys based upon a design by the Fairchild Space and Electronics Company, is also described. It is concluded that although the fabrication of reliable electrical contacts will present a major problem, the technology is available in Europe to build thermoelectric modules similar to those developed for the International Solar Polar mission. (orig.).
Energy Technology Data Exchange (ETDEWEB)
Pilot-plant irradiation began in Hungary in 1969 with the construction of a high-activity multi-purpose /sup 60/Co facility. Technologies for radiation sterilization, food handling, plastics irradiation as well as chemical dosimetry, semiconductor instrumental dosimetry, computer-based construction and control methods have been developed. Our chlorobenzene dose-meter system is used in Hungary and abroad; as a result of an IAEA-organized dosimetric intercomparison the system was adopted as a reference system. The institute has developed into a basic institute for the reconstruction and re-load of old ..gamma..-facilities as well as it serves for the planning, construction and launching of new ones in Hungary.
1982-01-01
New developments in capital cost estimating
Energy Technology Data Exchange (ETDEWEB)
The new developments in cost engineering revolve around the ability to capture information that in the past could not be automated. The purpose of automation is not to eliminate the expert cost engineer. The goal is to use available technology to have more information available to the professionals in the cost engineering field. In that sense, the demand for expertise increases in order to produce the highest quality estimate and project possible from all levels of cost engineers. We cannot overemphasize the importance of using a good source of expert information in building these types of programs. ''Garbage in, garbage out'' still applies in this form of programming. Expert systems technology will become commonplace in many vertical markets; it is important to undersand what can and cannot be accomplished in our field, and where this technology will lead us in the ...
1988-01-01
Geomechanical numerical simulations of complex geologic structures
Energy Technology Data Exchange (ETDEWEB)
Ability to predict mechanical response of rock in three dimensions over the spatial and time scales of geologic interest would give the oil and gas industry the ability to reduce risk on prospects, improve pre-project initial reserve estimates, and lower operating costs. A program has recently been initiated, under the auspices of the Advanced Computational Technology Initiative (ACTI), to achieve such a computational technology breakthrough by adapting the unique advanced quasistatic finite element technology developed by Sandia to the mechanics applications important to exploration and production activities within the oil and gas industry. As a precursor to that program, in an effort to evaluate the feasibility of the approach, several complex geologic structures of interest were analyzed with the existing two-dimensional quasistatic finite element code, SANTOS, developed at ...
1996-05-01
International Nuclear Information System (INIS)
This paper explores the current trends in development of technology-neutral safety requirements to be used in the regulation of future nuclear power reactors and the role of the quantitative safety goals in the design of reactor safety systems. Establishing the requirements concerning the reliability of safety functions rather than on particular systems employed to achieve the functions, as well as the use of the recommendations of the International Commission on Radiological Protection (ICRP) on protection against potential exposure could form the basis of a technology-neutral framework for safety requirements on new reactor designs. Also it could contribute to international harmonisation of nuclear safety assessment practices as part of the licensing processes for future nuclear power plants. (author)
2009-10-12
1,3 Propanediol and its copolymers: Research, development and industrialization
British Library Electronic Table of Contents (United Kingdom)
Abstract 1,3 Propanediol (PDO), is now taking the transition from a traditional specialty chemical to a commodity chemical . The market for PDO is growing rapidly as the technology develops. With the advancing PDO production technology, polytrimethylene terephthalate (PTT) as a new type of polyester has been applied in carpet and textile fibers, monofilaments, films, and nonwoven fabrics, and in the engineering thermoplastics area, because PTT has unique properties compared to other polymers such as polyethylene terephthalate (PET) and polybutylene terephthalate (PBT). Responding to the environmental and sustainability factors, one or two step fermentation technology for PDO production has attracted people's attention. A novel flexible process for PDO production by using aerobic fermentati...
2010-01-01
The development of technology on chicken yard design and its environment control
Energy Technology Data Exchange (ETDEWEB)
The objective of this study is development of technology on chicken yard design and its environment control. For this objective, the micro processor interface techniques and related programming techniques have been surveyed, and the chicken yard environment monitoring system has been developed that equipped with micro computer and signal measurement module. Software has also been developed that operated the system and analyzes measured data. By using micro computer and signal input/output module, the system can have various functions, such as monitoring, alarm, and data analysis function. Three dimensional graphic modeling of a chicken yard is performed using graphic package in this study. Application of three dimensional modeling technique make it easy to design chicken yard. 9 figs. (Author)
1996-04-01
Physics of laser fusion. Volume IV. The future development of high-power solid-state laser systems
Energy Technology Data Exchange (ETDEWEB)
Solid state lasers, particularly neodymium glass systems, have undergone intensive development during the last decade. In this paper, we review solid state laser technology in the context of high-peak-power systems for inertial confinement fusion. Specifically addressed are five major factors: efficiency, wavelength flexibility, average power, system complexity, and cost; these factors today limit broader application of the technology. We conclude that each of these factors can be greatly improved within current fundamental physical limits. We further conclude that the systematic development of new solid state laser madia, both vitreous and crystalline, should ultimately permit the development of wavelength-flexible, very high average power systems with overall efficiencies in the range of 10 to 20%.
1982-11-01
GTL or LNG: which is the best way to monetize ?stranded?? natural gas?
British Library Electronic Table of Contents (United Kingdom)
A large portion of world?s natural gas reserves are ?stranded?? resources, the drive to monetize these resources leads to the development of gas-to-liquids (GTL) and liquefied natural gas (LNG) technologies. LNG has the advantage of having been developed for the past 40 years and having an excellent safety record. GTL on the other hand is another option with substantial benefits, but its development stage and commercial viability are far behind LNG. This paper presents a techno-economic comparison of GTL with LNG, including technical development, plant efficiency, market potential for the products, and capital cost for the infrastructure. The aim is to give an overall view on both LNG and GTL and provide a perspective on the profitability of these two technologies.
2008-01-01
Development of Plasma Technologies at IPP NSC KIPT
International Nuclear Information System (INIS)
Plasma Technologies in Institute of Plasma Physics of the NSC KIPT are recently developed in the following directions. Material surfaces modification under their irradiation with pulsed plasma streams of different working gases. Besides traditional analysis of improvements of tribological characteristics and structural-phase changes of the modified layers recently we started investigations of material corrosions characteristic improvement under influence of pulsed plasma on the material surfaces. As to the surface coatings in arc discharges of Bulat type devices, new trends are related with multi-layers coatings, using Ti-AI-N coatings in cutting tools, using high frequency discharges or combined HF- and arc discharges for increasing the nomenclature of goods to be coated. Development of ozonators is respectively new area for IPP NSC KIPT. On the base of barrier high-frequency discharge there were ...
2001-09-19
Darrieus vertical axis wind turbine program overview
As a US Department of Energy (DOE) laboratory, Sandia Laboratories is developing Darrieus vertical axis wind turbine (VAWT) technology with the objective of encouraging private industry to produce economically feasible, commercially marketable wind energy systems. The first full cycle of development is essentially complete, and resulting current technology designs have been evaluated for cost-effectiveness. Aerodynamic, structural, and system analyses capabilities have evolved during this cycle to support and evaluate the system designs. This report presents some of the more salient recent developments, first generation costs, current activities, and future plans. Potential design improvements identified in the first development cycle are presented along with their cost benefits.
Annual report of JMTR. FY1997 (April 1, 1997 - March 31, 1998)
Energy Technology Data Exchange (ETDEWEB)
During FY1997, the JMTR was operated for 3 complete cycles (120th, 121st and 122nd cycles) and was utilized for the research and development programs on the technology of LWRs and fusion reactor, as well as for fundamental research of fuels and materials, and for radioisotope productions. The improvement of evaluation technique in a local neutron spectrum for irradiation utilization and development of capsule having the vertical migration, the reinstrumentation and loading mechanism have been carried out. Development of a new oxygen potential sensor for oxide fuel pellets has been done as an elemental technology of irradiation for high burn-up fuels. As for post irradiation examination, the techniques for measuring of crack length using an alternating current potential drop method and machining of miniaturized specimen by the remote handling have been developed. ...
1999-03-01
Airbags to Martian Landers: Analyses at Sandia National Laboratories
Energy Technology Data Exchange (ETDEWEB)
A new direction for the national laboratories is to assist US business with research and development, primarily through cooperative research and development agreements (CRADAs). Technology transfer to the private sector has been very successful as over 200 CRADAs are in place at Sandia. Because of these cooperative efforts, technology has evolved into some new areas not commonly associated with the former mission of the national laboratories. An example of this is the analysis of fabric structures. Explicit analyses and expertise in constructing parachutes led to the development of a next generation automobile airbag; which led to the construction, testing, and analysis of the Jet Propulsion Laboratory Mars Environmental Survey Lander; and finally led to the development of CAD based custom garment designs using 3D scanned images of the human body. The structural ...
1994-03-01
Power Tower Technology Roadmap and cost reduction plan.
Energy Technology Data Exchange (ETDEWEB)
Concentrating solar power (CSP) technologies continue to mature and are being deployed worldwide. Power towers will likely play an essential role in the future development of CSP due to their potential to provide dispatchable solar electricity at a low cost. This Power Tower Technology Roadmap has been developed by the U.S. Department of Energy (DOE) to describe the current technology, the improvement opportunities that exist for the technology, and the specific activities needed to reach the DOE programmatic target of providing competitively-priced electricity in the intermediate and baseload power markets by 2020. As a first step in developing this roadmap, a Power Tower Roadmap Workshop that included the tower industry, national laboratories, and DOE was held in March 2010. A number of technology improvement ...
2011-04-01
Energy Technology Data Exchange (ETDEWEB)
Technology is being developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation is introduced, and by modifying the surface of a base plate such as silica glass by using such peptides. Activities were conducted in the three areas of (1) creation of functional molecules, (2) materialization technology, and (3) comprehensive investigation and research; the activities were carried out independently and parallelly in the first two areas. In (1), design technique for the structures and functions of peptides was developed, as were conformational control technique, synthesis of peptides having optical/electronic functions, peptide synthesis by an enzyme method, and R and D on introduction of non-natural amino acid into peptides; in (2), element technologies were developed ...
1994-03-01
Energy Technology Data Exchange (ETDEWEB)
It is necessary to establish scenarios for reducing CO2 emissions and for developing CO2 emission control technologies to obtain a global consensus, using appropriate analytical models. For modification of the DNE-21 (Dynamic New Earth 21) model, it has a category designated as innovative technologies not involving CO2 emission and an optional consideration for the absorption of atmospheric CO2 by biomass. A global carbon circulation model, including vegetation in its scope, is also incorporated. Major results of the simulation are shown. When 20% reduction in CO2 emissions is required for only OECD countries after the year 2020, it has been demonstrated that CO2 concentration in the atmosphere will reach as high as about 900 ppm in 2100 due to CO2 emission by developing countries, and will not be a tolerable level. Under the condition that CO2 concentration in the atmosphere is controlled at 450 ppm in ...
1997-03-01
Energy Technology Data Exchange (ETDEWEB)
This paper describes an approach to the reliability engineering in aerospace technology. To promote development, configuration management (clarifies the base line of technology), reliability management, quality control, safety management, progress management, and cost management are very important. The following example related to reliability was contained for the development of an N-1 rocket in Japan. A timer and amplifier that are old-fashioned but have actual results were supplied from abroad. The induction system that was purchased from abroad contained faulty components in quality control. The improvement in reliability has priority and the first-stage tank was changed to a home-made aluminum alloy that is superior in stress-resistant corrosiveness. An H-II rocket was completely developed in Japan by self-technology. The number of faults to be generated in ...
1995-02-05
Development of engineering technology basis for industrialization of pyrometallurgical reprocessing
International Nuclear Information System (INIS)
Development of the engineering technology basis of pyrometallurgical reprocessing is a key issue for industrialization. For development of the transport technologies of molten salt and liquid cadmium at around 500 deg. C, a salt transport test rig and a metal transport test rig were installed in Ar glove box. Function of centrifugal pump and 1/2'' declined tubing were confirmed with LiCl- KCl molten salt. The transport behavior of molten salt was found to follow that of water. Function of centrifugal pump, vacuum sucking and 1/2'' declined tubing were confirmed with liquid Cd. With employing the transport technologies, industrialization applicable electro-refiner was newly designed and engineering-scale model was fabricated in Ar glove box. The electro-refiner has semi-continuous liquid Cd cathode instead of conventional one used in small-scale tests. With using actinide-simulating ...
2007-09-09
Spray Forming Aluminum - Final Report (Phase II)
Energy Technology Data Exchange (ETDEWEB)
The U.S. Department of Energy - Office of Industrial Technology (DOE) has an objective to increase energy efficient and enhance competitiveness of American metals industries. To support this objective, ALCOA Inc. entered into a cooperative program to develop spray forming technology for aluminum. This Phase II of the DOE Spray Forming Program would translate bench scale spray forming technology into a cost effective world class process for commercialization. Developments under DOE Cooperative Agreement No. DE-FC07-94ID13238 occurred during two time periods due to budgetary constraints; April 1994 through September 1996 and October 1997 and December 1998. During these periods, ALCOA Inc developed a linear spray forming nozzle and specific support processes capable of scale-up for commercial production of aluminum sheet alloy products. Emphasis was given to alloys ...
1999-07-08
Metrology measurement capabilities
Energy Technology Data Exchange (ETDEWEB)
Since 1958, the AlliedSignal Federal Manufacturing and Technologies (FM and T) Metrology Department has developed measurement technology and calibration capability in four major areas of measurement: mechanical; environmental, gas, liquid; electrical (D.C., A.C., RF/microwave); and optical and radiation. The capabilities developed include unique capabilities in many areas of measurement and engineering expertise to develop measurement techniques and resolve measurement problems in these major areas. FM and T Metrology was established in 1958 to provide a measurement base for the Department of energy`s Kansas City Plant. The Metrology Engineering Department provides the expertise to develop measurement capabilities for virtually any type of measurement which falls into the broad areas listed above. The engineering staff currently averages almost 16 years of ...
1997-06-01
Energy Technology Data Exchange (ETDEWEB)
The control of gas activity and process technology has developed tremendously over the past two decades. While once considered to be primitive control systems using simple PID loops with thermocouples that were suspect and unable to perform repeatedly and consistently during the arduous process of plasma nitriding and processing, developments in recent years have elevated the control of the process into what might be considered one of the most controllable processes of the latter part of this century. The advent of plasma processing technology has improved control methods by observing and harnessing each of the various process parameters into many different combinations of control systems. Some of these control systems can control the complete function of the process, thus freeing the operator entirely for other duties, except that of load and unload, to the point where the operator is intimately ...
1995-12-31
International Nuclear Information System (INIS)
Monitoring and diagnostic systems are of main importance for a safe and efficient operation of nuclear power plants. The author describes new developments with respect to vibration monitoring with a functional extension in the time domain for den secondary circuit, the development of a local system for the surveillance of rotating machines, the structure-borne sound monitoring with improvement of event analysis, esp. the loose part locating, leakage monitoring with a complete system for humidity measurement, and the development of a common platform for all monitoring and diagnostic systems, that allows an efficient access for comparison and cross references.
...Development of an Agroforestry Sequestration Project in Khammam District of India | International Energy Studies International Energy Studies News | Researchers | Publications ...Technologies Division Industrial Innovations Industrial Energy Analysis Copyright &1692006 Disclaimer Development of an Agroforestry Sequestration Project in Khammam District of India Authors:P. Sudha; V.... Vasistha 2006-10-10 0 Development of an Agroforestry Sequestration Project in Khammam District of India P. Sudha, V. Ramprasad, M.D.V. Nagendra,...
Mobil/Badger to market zeolite-based cumene technology
Energy Technology Data Exchange (ETDEWEB)
Badger (Cambridge, MA) and Mobil (Fairfax, VA) are ready to jointly license a new cumene technology that they say achieves higher yields and product purity than existing processes. The zeolite-based technology is scheduled to be introduced at next month's DeWitt Petrochemical Review in Houston. The Mobil/Badger technology aims to challenge the dominant position of UOP's (Des Plaines, IL) solid phosphoric acid (SPA) catalyst process - which accounts for 80%-90% of the world's cumene production. In addition, Monsanto/Kellogg's aluminum chloride-based technology has gained significant momentum since its introduction in the 1980s. And late last year, ABB Lummus Crest (Bloomfield, NJ) also began marketing a zeolite-based cumene technology. While all the technologies make cumene via the alkylation of benzene with propylene, the ...
1993-02-24
Potential for oil shale development in the United States
Energy Technology Data Exchange (ETDEWEB)
Over the past few years, the development of domestic oil shale resources has regained significant attention. High oil prices, emerging recovery technologies, increasing world demand for liquid hydrocarbons, and the continued decline in United States conventional oil production has contributed to this interest. Several initiatives have been undertaken by the United States federal government and the private sector to encourage the development of a domestic oil shale industry. The United States has nearly 2.0 trillion barrels of oil shale resources across the eastern and western states. However, the development of this massive resource is constrained by a number of key factors, such as resource access, technology, economics, infrastructure and environmental and regulatory issues. In order to review emerging oil shale technologies from 23 companies and identify ...
2009-07-01
Development of Pyro-separation Technology Based on Molten Salt Electrolysis
International Nuclear Information System (INIS)
The focus of this study was to develop recovery technologies in the pyroprocessing. The unit processes of the project can be classified into two groups; electro-refining process to recover uranium and long-lived nuclides, and cathode processing to produce a metal ingot both from a salt-contained metal and from Cd-contained metal. This project has been carried out for the third phase period of the long-term nuclear R and D program, and focused on the development of key technologies of the pyroprocessing such as electrorefining, draw down and cathode processing. Mock-up system of 1 kg-U/batch was built for performance tests which were conducted to ensure the adequacy of the research and development of the pyroprocessing technology. The experiments were carried out through bench-scale inactive tests except for uranium. In particular, the sticking problem was ...
2001-07-18
EARLY ENTRANCE COPRODUCTION PLANT
The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which uses petroleum coke to produce at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals using ChevronTexaco's proprietary gasification technology. The objective of Phase I is to determine the feasibility and define the concept for the EECP located at a specific site; develop a Research, Development, and Testing (RD&T) Plan to mitigate technical risks and barriers; and prepare a Preliminary Project Financing Plan. The objective of Phase II is to implement the work as outlined in the Phase I RD&T Plan to enhance the development and commercial acceptance of coproduction technology. The objective of Phase III is to develop an ...
2004-01-12
Technology Strategy Board Driving Innovation ...Technology Strategy 2009-2012 ... The vision of the Technology Strategy Board is for the UK to be a global leader in innovation
On the integration of technology readiness levels at Sandia National Laboratories.
Energy Technology Data Exchange (ETDEWEB)
Integrating technology readiness levels (TRL) into the management of engineering projects is critical to the mitigation of risk and improved customer/supplier communications. TRLs provide a common framework and language with which consistent comparisons of different technologies and approaches can be made. At Sandia National Laboratories, where technologies are developed, integrated and deployed into high consequence systems, the use of TRLs may be transformational. They are technology independent and span the full range of technology development including scientific and applied research, identification of customer requirements, modeling and simulation, identification of environments, testing and integration. With this report, we provide a reference set of definitions for TRLs and a brief history of TRLs at Sandia National Laboratories. We ...
2006-09-01
UK Achievements in the application of power fluidic technology for nuclear processing plants
International Nuclear Information System (INIS)
Power Fluidic systems for the control of liquids and gaseous flows have been adopted for use in radioactive processing plants in the UK. These devices are intrinsically reliable with no mechanical moving parts because they are able to make use of the hydrodynamics of the fluids being controlled. This reliability feature leads to a zero cell maintenance concept and the elimination of mechanical drive/control systems in cell. The first phase of the development work led to their use in the Fast Reactor Reprocessing Plant at Dounreay and the Highly Active Liquor Storage facility at Sellafield. The success of these early developments has led to an extensive development programme for an extended range of applications in the Thermal Oxide Reprocessing Plant and its associated waste treatment facilities at Sellafield. The technology has now been fully demonstrated and adopted for these plants with considerable ...
Review on the EFDA programme on tungsten materials technology and science
British Library Electronic Table of Contents (United Kingdom)
All the recent DEMO design studies for helium cooled divertors utilize tungsten materials and alloys, mainly due to their high temperature strength, good thermal conductivity, low erosion, and comparably low activation under neutron irradiation. The long-term objective of the EFDA fusion materials programme is to develop structural as well as armor materials in combination with the necessary production and fabrication technologies for future divertor concepts. The programmatic roadmap is structured into four engineering research lines which comprise fabrication process development, structural material development, armor material optimization, and irradiation performance testing, which are complemented by a fundamental research programme on "Materials Science and Modeling". This paper prese...
2011-01-01
Rethinking development assistance for wind power
Energy Technology Data Exchange (ETDEWEB)
Electricity generation from wind turbines is now cost competitive for grid and off-grid applications in many developing regions, and close to competitive in others. Wind resources could generate thousands of megawatts of badly-needed power in Asia, North Africa, and Latin America. Barriers to penetrating power generation markets remain, however, including unequal access to investment capital, energy price and other market distortions, and often weak institutions for commercializing new technologies. Recognizing the potential economic and environmental benefits of wind power, bilateral and multilateral assistance organizations have for several years offered financial and technical assistance to promote its diffusion. Based on this experience and assistance for other renewable electric technologies, lessons and recommendations can be drawn regarding how assistance could more effectively overcome persistent market and policy ...
1995-12-31
Energy Technology Data Exchange (ETDEWEB)
The Canada Centre for Mineral and Energy Technology (CANMET) is a research organization dedicated to the advancement of the Canadian mining industry. It specializes in the development of new technologies and the coordination of scientific partnerships in the fields of mines, metallurgical processes, and the environment. CANMET supports a number of research and development activities related to the mining industry. In this poster presentation, the author described the mandate of CANMET by first introducing the organization chart with a special emphasis placed on the Mining and Mineral Sciences Laboratories. A description of the different types of partnerships was included, followed by specific details concerning all the projects related to the mining industry, such as terrain control, automation of mines, underground mining environment, processes and services, analytical support, environmental programs, ...
2000-07-01
Flywheel rotor and containment technology development, FY83
Energy Technology Data Exchange (ETDEWEB)
The Department of Energy decided to terminate the Flywheel Rotor and Containment Technology Development project during FY 1983. Activities this year included fabrication, inspection, and test evaluation of rotor and containment structures. A peak energy of 700 Wh was stored at an energy density of 70 Wh/kg. In cyclic tests, 10,000 cycles from design speed to half speed were logged without failure. The first test of a lightweight containment structure indicates the need for additional development. In complementary studies, production cost estimates were made for three flywheel designs. In a cooperative program with the University of Wisconsin, work began on construction of a flywheel/continuously variable transmission/heat engine car which promises fuel economy improvements of up to 100%. Suggestions are made for the direction of future work when interest in flywheel system reappears.
1983-09-12
Canadian R&D on oil-fired combustion systems
Energy Technology Data Exchange (ETDEWEB)
This paper describes research and development presently being conducted on oil-fired space and tap water heating systems by the Advanced Combustion Technology Group, CCRL/ERL/CANMET, in Ottawa, Canada. The presentation will focus on R&D activities at CCRL in support of the Canadian Oil Heat Association (COHA) and of the energy policy initiatives of Natural Resources Canada. Progress will be reported on activities to develop suitable oil-fired integrated systems to satisfy the low energy demands of new homes. The utilization of fuzzy logic-based control heating systems including fan coils for a complete range of old and new North American housing will be discussed. Additional activities to be discussed in the presentation will relate to the development of appropriate seasonal efficiency standards for complex integrated space/water heating systems, as well as an evaluation of alternative sidewall ...
1996-07-01
The green car on the up. Groene auto in opmars
Energy Technology Data Exchange (ETDEWEB)
An overview of the developments and designs of electric cars is given. It can be concluded that the numbers of electric-powered vehicles in the world, presented by different companies, are confusing and that it is very difficult to categorize the electric cars because of the many different prototypes under development sofar. Also an introduction is given on the engine technology of such cars. Attention is paid to the direct current (DC) motor, the induction motor, the brushless DC-motor, and the synchronous motor. 2 figs., 4 ills., 35 refs.
1992-09-01
Progress of JAERI neutron science project
Energy Technology Data Exchange (ETDEWEB)
Neutron Science Project was started at Japan Atomic Energy Research Institute since 1996 for promoting futuristic basic science and nuclear technology utilizing neutrons. For this purpose, research and developments of intense proton accelerator and spallation neutron target were initiated. The present paper describes the current status of such research and developments. (author)
1999-03-01
Process in Plasma Research at IPJ and IPPLM, POLAND
International Nuclear Information System (INIS)
The most important results of theoretical and experimental studies of plasmas, which have been achieved at the IPJ in Swierk and IPPLM in Warsaw recently, are presented. Studies of physical phenomena in PF discharges, development of diagnostic techniques and research on new plasma technologies, as performed at IPJ, have been summarized. Studies of dense magnetized plasmas, investigation of physics and applications of laser-produced plasmas; and research on the development of advanced diagnostic techniques for the EUROATOM fusion program, as performed at IPPLM, are also described.
2006-01-01
The developments of fields in deep waters (5000 ft and more) is a common occurrence. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas-oil-and water possibly along with sand, hydrates, and wax...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
A consortium has been formed to undertake the design and development work necessary to establish a comprehensive machine condition monitoring (MCM) and diagnostic system for hydroelectric generating units. By working closely with participating utilities and interested manufacturers, the consortium is initiating the integration of existing and developing technologies into a comprehensive, modular, on- and off-line hydroelectric MCM system.
1995-12-31
Levels of ICT use in teaching and administration
DEFF Research Database (Denmark)
The computer facilities and the computer expertise at certain departments at Aalborg University made these departments natural starting points for integration of Information and Communication Technology (ICT) in their activities. This utilization and integration of ICT was not organized from the top or intermediate levels. It developed from the grassroots. Today Aalborg University as a whole can be said to be a truly ICT integrated institution. The quick development is to a high extent due to a structure with a finely distributed system of equipment, know-how and autonomy at all levels
2000-01-01
Laser applications. Final report
Energy Technology Data Exchange (ETDEWEB)
Processes were developed that use lasers as manufacturing tools. These processes were stripping of insulation from cables and wires, machining of quartz, microdrilling and welding of reflective metals, and precision alignment of curved surfaces before machining. A technological basis also was formed which resulted in a process for automatic surface inspection of parts and aided development of machining processes for Kevlar parts.
1980-07-01
Improving airport explosives detection
Energy Technology Data Exchange (ETDEWEB)
ORNL has developed the technology to detect hidden explosives in luggage using X ray and neutron detection devices. The Federal Aviation Administration has ordered the airlines to buy and install Thermal Neutron Analysis (TNA) units. The combined pulsed-neutron and X-ray interrogation inspection (CPNX) system developed at ORNL uses less radioactive materials as well as being more sensitive to weapons, electronic devices and plastic explosives.
1990-01-01
Future research on transonic unsteady aerodynamics and its aeroelastic applications
Energy Technology Data Exchange (ETDEWEB)
The workshop focused on strategies for promoting and developing engineering level transonic flutter prediction techniques. The technology of transonic aerodynamics is currently undergoing rapid development. Significant progress is being made to solve the inherently nonlinear equations describing unsteady motions of wings in transonic flow, while the availability of reliable and efficient computational methods will greatly enhance the ability to predict the aeroelastic behavior of modern aircraft operating under transonic flow conditions.
1987-08-01
Energy Technology Data Exchange (ETDEWEB)
Accounts are given of the history of coal liquefaction research and projects (indirect liquefaction, direct liquefaction, plus the recent state of Japanese developments and of process development), and of the significance of the petroleum age, the energy crisis and of coal liquefaction itself. (10 refs.) (In Japanese)
1982-01-01
FY 1999 Laboratory Directed Research and Development annual report
Energy Technology Data Exchange (ETDEWEB)
A short synopsis of each project is given covering the following main areas of research and development: Atmospheric sciences; Biotechnology; Chemical and instrumentation analysis; Computer and information science; Design and manufacture engineering; Ecological science; Electronics and sensors; Experimental technology; Health protection and dosimetry; Hydrologic and geologic science; Marine sciences; Materials science; Nuclear science and engineering; Process science and engineering; Sociotechnical systems analysis; Statistics and applied mathematics; and Thermal and energy systems.
2000-06-13
Energy Technology Data Exchange (ETDEWEB)
There have been no radically new commercial bulk explosives since Atlas Powder Company's introduction of emulsions onto the market in 1968. But the effectiveness, safety and management of these familiar explosives is continuously being improved by the development of blast design techniques, explosives delivery and initiation systems, and monitoring methods. The author looks at developments in blasting technology and discusses experiences with Handibulk emulsion delivery systems.
1994-02-01
Energy storage systems program report for FY1996
Energy Technology Data Exchange (ETDEWEB)
Sandia National Laboratories, New Mexico, conducts the Energy Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Utility Technologies. The goal of this program is to assist industry in developing cost-effective energy storage systems as a resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of energy storage systems for stationary applications. This report details the technical achievements realized during fiscal year 1996.
1997-05-01
Eighth ocean energy conference: preliminary report
Energy Technology Data Exchange (ETDEWEB)
A series of speeches is presented which cover political aspects of ocean energy, legislation, the status of the DOE Ocean Energy Program, the Maritime Administration OTEC Support Program. Six workshop reports are given covering ocean energy technology and systems concepts, power systems concepts, environmental developments, energy transfer and utilization, construction and test capabilities, and industry development. (LEW)
1981-01-01
Diagnostic and Therapeutic RI Generators
Energy Technology Data Exchange (ETDEWEB)
Different types of generators have been developed for the convenient use of {sup 99m}Tc as the demand for this radioisotope is strong. Currently, the demand for {sup 99m}Tc is more than 80 % of the total demand for medical isotopes in the world. A {sup 99m}Tc generator, in general, is composed of a column packed with ceramic adsorbent, tubing, eluent reservoir or vials, collection vials, and shielding. The key technology to develop a good generator is how to load {sup 99}Mo as much as possible while maintaining the quality of eluted {sup 99}mTc as good as possible. The technology is well developed and already available commercially for the case of the fission {sup 99}Mo/{sup 99}mTc because loading of few curries of {sup 99}Mo on a conventional adsorbent, i.e. alumina is not a serious task in the chemical point of view. However, the current infrastructure of the supply of {sup 99}Mo ...
2006-07-01
Developments and potential of radiation processing in the Philippines
Energy Technology Data Exchange (ETDEWEB)
This paper describes the research and development activities in three areas of radiation processing, namely: food irradiation, medical product sterilization and wood plastic combination. Plans and efforts exerted to acquire a larger gamma source to augment our present 5,000 curie source are discussed. Cost estimates for a radiation facility are presented on the basis of the market potential of food irradiation and medical product sterilization. Existing local industries that can benefit from the adaptation of irradiation technology in their processing requirements are described.
1981-01-01
Development of pressurized internally circulating fluidized-bed (PICFB) technology
Energy Technology Data Exchange (ETDEWEB)
After the completion of the 4MWth pilot plant of the Pressurizied Internally Circulating Fluidized-bed Boiler (PICFB), a total of 15 test runs, amounting to 2280 hours of operation, were concluded. The test results have confirmed the superior operating performance. Additionally, Ebara plans to develop a Pressurized Internally Circulating Fluidized-bed Gasifier (PICFG or Advanced PICFB). 8 figs.
1998-07-01
Development of High-Efficiency Low-Lift Vapor Compression System - Final Report
Energy Technology Data Exchange (ETDEWEB)
PNNL, with cofunding from the Bonneville Power Administration (BPA) and Building Technologies Program, conducted a research and development activity targeted at addressing the energy efficiency goals targeted in the BPA roadmap. PNNL investigated an integrated heating, ventilation and air conditioning (HVAC) system option referred to as the low-lift cooling system that potentially offers an increase in HVAC energy performance relative to ASHRAE Standard 90.1-2004.
2010-03-31
Community Geothermal Technology Program: Hawaii glass project. Final report
Energy Technology Data Exchange (ETDEWEB)
Objective was to develop a glass utilizing the silica waste material from geothermal energy production, and to supply local artists with this glass to make artistic objects. A glass composed of 93% indigenous Hawaiian materials was developed; 24 artists made 110 objects from this glass. A market was found for art objects made from this material.
1988-01-20
Energy Technology Data Exchange (ETDEWEB)
The development of a synthetic fuels industry in Australia is described in the context of overall energy policy. The national coal liquefaction research program is directed at three main routes to liquid fuels: hydroliquefaction, pyrolysis and indirect liquefaction. Australia is also contributing to technology development and assessment programs in cooperation with other countries, in particular Federal Republic of Germany and Japan.
1981-11-01
Building a sustainable energy system
Energy Technology Data Exchange (ETDEWEB)
The inevitability of sustainable economic development and its linkage to a gradual shift to renewable energy sources, especially solar energy, was discussed. Means to measure sustainability of technology were described, and policy instruments (essentially research, development and demonstration, and punitive taxes on conventional energy carriers) to accelerate the shift to renewable energy sources were outlined.
1995-12-31
Analysis of the MEX-15 multipurpose reactor using SRAC code system
Energy Technology Data Exchange (ETDEWEB)
The MEX-15 is a conceptual design of a Multipurpose Reactor with thermal power of 15 MW and this reactor is pool type with fuel plates U{sub 3}0{sub 8}-Al of low enrichment uranium. This report presents the static calculation for the MEX-15 reactor using SRAC code system and was developed under the collaboration agreement between ININ-JAERI in Research Reactor Technology Development Division of Department of Research Reactor in Tokai Research Establishment. (Author)
1992-12-15
Energy Technology Data Exchange (ETDEWEB)
This work, carried out by the parliamentary office for the evaluation of scientific and technological choices on request of the French National Assembly and Senate, takes stock of the present day situation and technical perspectives of development of renewable energy sources and of research needs of the French industry in this domain: 1 - renewable energies: key-technologies for the energy supply of developing countries and for a rational consumption in transportation systems and accommodations of developed countries (energies technically different from fossil or nuclear energies; fundamental energy sources for a developing world; different national goals in Europe depending on the available natural resources and on the political realities; a minor interest in France for the domestic power generation but a major interest for transports, residential and tertiary ...
2001-11-01
Renewable energy technology from underpinning physics to engineering application
International Nuclear Information System (INIS)
The UK Energy Research Centre (UKERC) in it's submission to the DTI's 2006 Energy Review reminded us that the 'UK has abundant wind, wave and tidal resources available; its mild climate lends itself to bio-energy production, and solar radiation levels are sufficient to sustain a viable solar industry'. These technologies are at different stages of development but they all draw on basic and applied Science and Engineering. The paper will briefly review the renewable energy technologies and their potential for contributing to a sustainable energy supply. Three research topics will be highlighted that bridge the gap between the physics underpinning the energy conversion, and the engineering aspects of development and deployment; all three are highly relevant to the Government's programme on micro-generation. Two are these are taken from field of thin film photovoltaics (PV), one related to novel device ...
2008-03-01
Recent status of the development of intense ion beams
Energy Technology Data Exchange (ETDEWEB)
Taking the development of large current, negative ion sources which is in progress aiming at nuclear fusion reactors and the development of high luminance ion sources planned as a part of the Omega Project as the examples, the technology for generating high power ion beams is explained. Both these projects are positioned at the limit of the present technology of high power ion beam application as their targeted beam power reaches several tens MW. Consequently, the requirement for the ion sources is severe, and in particular, the generation of the ion beams having large current density with good convergence is beyond all precedents. The application of high power ion sources has been realized as the neutral beam injectors for large tokamaks. Also the hydrogen negative ion source of large current and the electrostatic acceleration technology for negative ion beams have been ...
1993-12-01
Real-time 3-D SAFT-UT system evaluation and validation
International Nuclear Information System (INIS)
SAFT-UT technology is shown to provide significant enhancements to the inspection of materials used in US nuclear power plants. This report provides guidelines for the implementation of SAFT-UT technology and shows the results from its application. An overview of the development of SAFT-UT is provided so that the reader may become familiar with the technology. Then the basic fundamentals are presented with an extensive list of references. A comprehensive operating procedure, which is used in conjunction with the SAFT-UT field system developed by Pacific Northwest Laboratory (PNL), provides the recipe for both SAFT data acquisition and analysis. The specification for the hardware implementation is provided for the SAFT-UT system along with a description of the subsequent developments and improvements. One development of technical interest is ...
1993-05-17
NASA's capabilities in advanced energy research and development
International Nuclear Information System (INIS)
A 2007 report compiled by members of the armed services indicates that climate change presents a serious security threat to the American public as well as to United States military operations. It is likely that climate change will increase global tensions and competition for resources. This presentation discussed advanced research and technology programs conducted by the National Aeronautics and Space Administration (NASA). Scientists and engineers at NASA have developed a number of technologies that may contribute to American energy security. Advanced energy research and development programs initiated by the organization include advanced heat engines; wind turbines; batteries and electric cars; solar photovoltaics; and fuel cell technologies. NASA's aeronautics and space exploration program has several capabilities relevant to advanced wind power systems. A collaborative program is ...
2010-02-22
Energy Technology Data Exchange (ETDEWEB)
The Project ``Middle School Integrated Science, Mathematics and Technology Curriculum`` had two goals: (1) to survey the literature of energy education; and (2) to develop a theme for a possible integrated middle school energy based curriculum. We aimed to respond to the challenge of developing thematic integrated curricula as advocated by the NSTA, AAAS and other organizations analyzing the future of American science and mathematics education. The survey of middle school energy curriculum materials has been completed. A list of the resources surveyed are included in this report. Though many energy based curriculum materials have been produced, none of them appears to be broadly disseminated throughout the country. Some energy based curriculum materials are far less well developed than others. We found that an integrated set of modular materials concerning the energy based theme of light and optics does ...
1994-03-01
Advanced evaporator technology progress report FY 1992
Energy Technology Data Exchange (ETDEWEB)
This report summarizes the work that was completed in FY 1992 on the program {open_quotes}Technology Development for Concentrating Process Streams.{close_quotes} The purpose of this program is to evaluate and develop evaporator technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process. Concentrating these streams and minimizing the volume of waste generated can significantly reduce disposal costs; however, equipment to concentrate the streams and recycle the decontaminated condensates must be installed. LICON, Inc., is developing an evaporator that shows a great deal of potential for this application. In this report, concepts that need to be incorporated into the design of an evaporator operated in a radioactive environment are discussed. These concepts include criticality safety, remote operation and maintenance, and materials ...
1995-01-01
Transitioning DARPA Technology
Page 1. TRANSITIONING DARPA TECHNOLOGY ... Transitioning DARPA Technology JAMESJ.RJCHARDSON DIANE L. LARRNA ...
2001-05-01
The next wave : kaleidoscope project aims to break the sound barrier of seismic imaging
Energy Technology Data Exchange (ETDEWEB)
This article discussed a project formed to develop innovative seismic imaging technologies. The Kaleidoscope project aims to accelerate the processing of seismic sound waves by several orders of magnitude using advanced computer-based techniques to reveal oil and gas deposits buried deep in the earth in a manner that is both cost-effective and efficient. It is expected that the technology will be used in deep water applications with massive untapped reserves. The seismic technology will be used to locate hydrocarbons and oil reserves buried 20,000 feet beneath the seabed. It is estimated that the Gulf of Mexico contains 56 billion barrels of oil equivalent worth nearly $6 trillion. However, the reserves are difficult to locate due to the interbedded salt bodies in the subsurface. The project is simultaneously working on both hardware and software applications, and are currently writing the first ...
2008-05-15
International Nuclear Information System (INIS)
The International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) was launched in the year 2000, based on a resolution by the IAEA General Conference (GC(44)/RES/21). INPRO intends to help to ensure that nuclear energy is available in the 21st century in a sustainable manner, and seeks to bring together all interested Member States, both technology holders and technology users, to consider, jointly, actions to achieve desired innovations. INPRO is taking care of the specific needs of developing countries. This IAEA publication is part of Phase 1 of INPRO. It intends to provide an overview on history, present situation and future perspectives of nuclear fuel cycle technologies. While this overview focuses on technical issues, nevertheless, the aspects of economics, environment, and safety and proliferation resistance are important background issues for this study. After a brief description ...
1991-01-01
Status Report of Simulated Space Radiation Environment Facility
Energy Technology Data Exchange (ETDEWEB)
The technology for performance testing and improvement of materials which are durable at space environment is a military related technology and veiled and securely regulated in advanced countries such as US and Russia. This core technology cannot be easily transferred to other country too. Therefore, this technology is the most fundamental and necessary research area for the successful establishment of space environment system. Since the task for evaluating the effects of space materials and components by space radiation plays important role in satellite lifetime extension and running failure percentage decrease, it is necessary to establish simulated space radiation facility and systematic testing procedure. This report has dealt with the status of the technology to enable the simulation of space environment effects, including the effect of space radiation on space materials. This ...
2007-11-15
Energy Technology Data Exchange (ETDEWEB)
To address the need for integrated models of advanced power generation systems and for improved analysis techniques, the US Department of Energy (DOE), through the Morgantown Energy Technology Center (METC), has supported the development of performance, emissions, and cost models of several advanced power generation systems, including integrated gasification combined cycle (IGCC), externally-fired combined cycle (EFCC) and pressurized fluidized bed combustion (PFBC) concepts. Simultaneously, numerical methods for simulation of uncertainties and optimization of process flowsheets have been implemented in the DOE`s public version of ASPEN. The new process models and computational capabilities have been applied to demonstrate the benefits of quantitative approaches to dealing with uncertainty and for optimizing technologies in the face of uncertainty. This paper focuses on modeling and assessment of the EFCC system concept. ...
1996-10-01
Comparison of Students' Success in an International Technology Certificate Program
There has been a rapid increase in the number of technology certificate programs offered around the world in the last decade. While designing, developing, and implementing these programs little or no consideration is given to geographical, cultural and developmental differences between different regions of the world. This study investigates the students' success in the Cisco Certified Network Associate (CCNA) program--a unique model combining technology-supported learning with local instruction world-wide. The purpose of this study is to investigate how demographic, ability, and motivational factors impact student success in different regions of the world when the curriculum and teaching materials are the same for all students and teachers. 368,159 students who completed the technology course from August 2004 to December 2005 in 5,948 academies in 135 countries were examined. Based on ANOVA and ...
2007-12-01
Theory and evidence of economies of scale in the development of waste management systems
Energy Technology Data Exchange (ETDEWEB)
Waste is a cost of doing business. This cost can be considered in terms of the potential adverse health and environmental impacts, or the waste management costs associated with avoiding, minimizing, and controlling those impacts. There is an anticipated increase in the cost of waste management as a result of the increasing requirements for regulatory compliance. To meet the total waste management capacity needs of the organization and the compliance requirements, low-level radioactive, hazardous, and mixed waste management will need demonstrated technologies strategically managed as a technology portfolio. The role of the decision maker is to select the optimum mix of technologies and facilities to provide the waste management capacity needed for the next twenty years. The waste management system resulting from this mix includes multiple small-scale fixed facilities, large-scale centralized facilities, and waste management ...
1989-01-01
Energy Technology Data Exchange (ETDEWEB)
A couple of domestic institutions have been investigating the application of vitrification technology to treat low- and intermediate-level radioactive wastes in Korea. In the case that such investigations prove to be successful, it is expected that commercial vitrification plants will be constructed. The safety insuring on vitrification plants could not be compatible with criterion on radioactive waste management because the facilities are at high temperature and contain a variety of accommodations for the exhaust gases and residual products. Therefore, it is necessary to suggest a new strategy or modifications of criterion of radioactive waste management on considerations related with the vitrification technology. In order to ensure the safety of vitrification plants, a technical guideline or standard for design and operation of vitrification plants must be established too. A study on the safety assessment of vitrification plants in ...
2003-02-25
Energy Technology Data Exchange (ETDEWEB)
The Electrochemical Technology Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE`s Electric and Hybrid Propulsion Division (DOE-EBP). The goal of DOE-EHP is to advance promising EV propulsion technologies to levels where industry will continue their commercial development and thereby significantly reduce petroleum consumption in the transportation sector of the US economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R&D contracts on advanced battery and fuel cell technologies for DOE-EBP. This report summarizes the objectives, background, technical progress, and status of ANL electric vehicle battery R&D tasks for DOE-EHP during the period of October 1, 1990 through December 31, 1990. The work is ...
1990-12-31
The ANL electric vehicle battery R D program for DOE-EHP
Energy Technology Data Exchange (ETDEWEB)
The Electrochemical Technology Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE's Electric and Hybrid Propulsion Division (DOE-EBP). The goal of DOE-EHP is to advance promising EV propulsion technologies to levels where industry will continue their commercial development and thereby significantly reduce petroleum consumption in the transportation sector of the US economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R D contracts on advanced battery and fuel cell technologies for DOE-EBP. This report summarizes the objectives, background, technical progress, and status of ANL electric vehicle battery R D tasks for DOE-EHP during the period of October 1, 1990 through December 31, 1990. The work is ...
1990-01-01
Separation Science and Technology. Semiannual progress report, April 1993--September 1993
Energy Technology Data Exchange (ETDEWEB)
This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1993. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Other projects are underway with the objective of developing (1) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process, (2) treatment schemes for liquid wastes stored or being generated at Argonne, (3) a process based on sorbing modified TRUEX solvent on magnetic beads to be used for separation of ...
1996-01-01
Energy Technology Data Exchange (ETDEWEB)
Studies are made on coal in terms of its effective utilization, coal cleaning, fluidization and production of new fuel, and issues globally raised. Coal is abundant in reserves and high in supply stability and economic efficiency. However, it is much in CO2 emission per calorific value. To control as much CO2 emission as possible, effective utilization such as increasing of power generation efficiency has been proceeded with. In addition to ultra supercritical pressure and fluidized bed combustion, cited are coal gasification combined cycle power generation and high temperature type fuel cell. Coal has 5-20% ash and impurities like sulfur/nitrogen. Coal should be used clean by pollution abatement measures such as dust collecting, desulfurization and denitrification. Japan is at a world top level of these technologies. Coal is solid, and therefore, is more difficult to handle than liquid fuel. To use it easily, coal is liquefied into slurry such as COM and CWM, and ...
1994-04-25
Energy Technology Data Exchange (ETDEWEB)
Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash ...
1992-01-01
Magnetic liquefier for hydrogen
Energy Technology Data Exchange (ETDEWEB)
This document summarizes work done at the Astronautics Technology Center of the Astronautics Corporation of America (ACA) in Phase 1 of a four phase program leading to the development of a magnetic liquefier for hydrogen. The project involves the design, fabrication, installation, and operation of a hydrogen liquefier providing significantly reduced capital and operating costs, compared to present liquefiers. To achieve this goal, magnetic refrigeration, a recently developed, highly efficient refrigeration technology, will be used for the liquefaction process. Phase 1 project tasks included liquefier conceptual design and analysis, preliminary design of promising configurations, design selection, and detailed design of the selected design. Fabrication drawings and vendor specifications for the selected design were completed during detailed design. The design of a subscale, demonstration magnetic ...
1992-12-31
In Situ Remediation Integrated Program: FY 1994 program summary
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy (DOE) established the Office of Technology Development (EM-50) as an element of the Office of Environmental Management (EM) in November 1989. In an effort to focus resources and address priority needs, EM-50 introduced the concept of integrated programs (IPs) and integrated demonstrations (IDs). The In Situ Remediation Integrated Program (ISR IP) focuses research and development on the in-place treatment of contaminated environmental media, such as soil and groundwater, and the containment of contaminants to prevent the contaminants from spreading through the environment. Using in situ remediation technologies to clean up DOE sites minimizes adverse health effects on workers and the public by reducing contact exposure. The technologies also reduce cleanup costs by orders of magnitude. This report summarizes project work conducted in FY 1994 under the ISR ...
1995-04-01
High power nickel - cadmium cells with fiber electrodes (FNC)
International Nuclear Information System (INIS)
Nickel cadmium batteries differ greatly in their mechanical design and construction of the electrodes. Using available electrode constructions, batteries are designed which meet the requirements of specific applications and offer optimum performance. Pocket- and tubular cells are basically developed with the technology of the year 1895. Since then some improvements with todays technology have been made. The sintered cells use the technology of the 1930's and they are still limited to high power application. With this knowledge and the technology of today the fiber-structured nickel electrode (FNC) was developed at DAUG laboratory, a subsidiary company of Mercedes-Benz and Volkswagen. After ten years of experience in light weight prototype batteries for electric vehicles (1-2), the system was brought into production by a new company, DAUG-HOPPECKE. ...
Energy Technology Data Exchange (ETDEWEB)
This summary denotes the progress made by the Exploratory Technology Research (ETR) Program for Electrochemical Energy Storage during calendar year 1992. The primary objective of the ETR Program, which is sponsored by the US Department of Energy (DOE) and managed by Lawrence Berkeley Laboratory (LBL), is to identify electrochemical technologies that can satisfy stringent performance, durability and economic requirements for electric vehicles (EVs). The ultimate goal is to transfer the most-promising electrochemical technologies to the private sector or to another DOE program (e.g., SNL`s Electric Vehicle Advanced Battery Systems Development Program, EVABS) for further development and scale-up. Besides LBL, which has overall responsibility for the ETR Program, LANL and BNL have participated in the ETR Program by providing key research support in several of the program elements. ...
1993-10-01
Electrofuel 2000 annual report : leading the charge
International Nuclear Information System (INIS)
Electrofuel Inc. develops, manufactures and sells a lithium ion superpolymer rechargeable battery technology. This unique and breakthrough technology provides the highest energy density and longest lasting portable power source on the market today. The company's goal is to become the leading provider of portable power for the portable computer and wireless sectors and to apply its technology to a wide range of alternative energy applications. The market for this technology is large and growing rapidly. Sales have increased from 190 million devices in 1998 to a projected 600 million in 2003. The increased sales are driven by better affordability, reduced size and functionality of the battery. This annual report highlights some of the major milestones the company achieved in 2000 which helped advance the corporate strategy and which marked its transformation from a late stage ...
2001-01-01
This report describes the results of work conducted during February 1982 - January 1983. A literature search was initiated to identify the state-of-the-art of NOx (NO + NO/sub 2/) reduction technologies, including NOx measurement methodologies, air infiltration and ventilation trends, the impact of NOx (NO/sub 2/) emissions on health, and air quality standards. As a result of the literature search NOx (NO/sub 2/) reduction goals were established for the project and technologies to achieve these goals identified. This report also covers the development of a prototype burner which examined flue gas recirculation, burner designs, secondary air baffling and flame inserts as potential technologies to reduce NOx (NO/sub 2/). Because of their potential for NOx (NO/sub 2/) reduction shown by initial experiments, an in-depth analysis of ring insert configurations was conducted. These results, along with other ...
1983-02-28
Commercializing research: the leadership challenges for the 21st century
International Nuclear Information System (INIS)
R and D today is a large industry that consumes vast amounts of public and private funds in most countries. It is becoming increasingly evident that technology transfer and the commercialization of research done at universities and government funded research laboratories must be a key element of their comprehensive strategic plan. It involves using a verified and organized knowledge and research to develop commercially viable products. It requires a visionary leader with effective project management skills to manage and motivate a team of scientists and engineers, otherwise even a top rated researcher will enervate and wither within the walls of research laboratories. This paper will highlight the importance, challenges and techniques of commercializing technology from accelerator research laboratories. It will provide an overview of the requirements of scientific leadership for both commercialization of research and ...
2000-06-26
Clean Coal Program Research Activities
Although remarkable progress has been made in developing technologies for the clean and efficient utilization of coal, the biggest challenge in the utilization of coal is still the protection of the environment. Specifically, electric utilities face increasingly stringent restriction on the emissions of NO{sub x} and SO{sub x}, new mercury emission standards, and mounting pressure for the mitigation of CO{sub 2} emissions, an environmental challenge that is greater than any they have previously faced. The Utah Clean Coal Program addressed issues related to innovations for existing power plants including retrofit technologies for carbon capture and sequestration (CCS) or green field plants with CCS. The Program focused on the following areas: simulation, mercury control, oxycoal combustion, gasification, sequestration, chemical looping combustion, materials investigations and student research experiences. The goal of this ...
2009-03-31
Enabling Technology for Monitoring & Predicting Gas Turbine Health & Performance in IGCC Powerplants
Energy Technology Data Exchange (ETDEWEB)
The ''Enabling & Information Technology To Increase RAM for Advanced Powerplants'' program, by DOE request, was re-directed, de-scoped to two tasks, shortened to a 2-year period of performance, and refocused to develop, validate and accelerate the commercial use of enabling materials technologies and sensors for coal/IGCC powerplants. The new program was re-titled ''Enabling Technology for Monitoring & Predicting Gas Turbine Health & Performance in IGCC Powerplants''. This final report summarizes the work accomplished from March 1, 2003 to March 31, 2004 on the four original tasks, and the work accomplished from April 1, 2004 to July 30, 2005 on the two re-directed tasks. The program Tasks are summarized below: Task 1--IGCC Environmental Impact on high Temperature Materials: The first task was refocused to address IGCC ...
2005-12-01
Using Multiple Unmanned Systems for a Site Security Task
Energy Technology Data Exchange (ETDEWEB)
Unmanned systems are often used to augment the ability of humans to perform challenging tasks. While the value of individual unmanned vehicles have been proven for a variety of tasks, it is less understood how multiple unmanned systems should be used together to accomplish larger missions such as site security. The purpose of this paper is to discuss efforts by researchers at the Idaho National Laboratory (INL) to explore the utility and practicality of operating multiple unmanned systems for a site security mission. This paper reviews the technology developed for a multi-agent mission and summarizes the lessons-learned from a technology demonstration.
2009-04-01
Underground electric-power transmission-system environmental impact assessment
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy, Division of Electric Energy Systems, has undertaken to identify the environmental issues and potential impacts associated with the installation of underground electric power transmission systems. This study reports the results of investigations into the advanced cable technologies being considered for future underground applications, as part of the development oriented research program of the Division of Electric Energy Systems. While the technology involves a high level of sophistication, there are relatively few impacts to the environment that are potentially significant, and of these none are inherently non-mitigable. Route planning, system design, and methods of construction and accident response can be pursued in order to minimize impacts where strict constraints are appropriate.
1982-03-01
British Library Electronic Table of Contents (United Kingdom)
The online communicative environment is expected to revolutionize political discourse as it expands to cover underrepresented groups and ideas. In this platform, marginalized groups such as indigenous communities from the developing world can articulate claims, strategically mobilize and participate in the forms of meaning-making that constitute them. However, there is skepticism on the actual value of online spaces in effecting agency in an internet-mediated environment. Using James Scott's notion of 'hidden transcripts' and Andrew Feenberg's 'democratic rationalization of technology', the paper explores strategic approaches and historical, social, and political conditions embedded in the construction, negotiation, and transformation of indigenous online activist media. In-depth interview...
2012-01-01
The application of advanced techniques for complex focused-ion-beam device modification
Energy Technology Data Exchange (ETDEWEB)
Advanced techniques for focused-ion-beam (FIB) device modification have been developed for complex, multistep modifications to circuitry on planar chip technology. Applying gas-assisted etching (GAE) techniques for high-aspect-ratio milling and the selective milling of both conductive and insulating films enhances process latitude. Localized ion-beam-induced deposition of an insulating film provides reconstructive capability in previously modified areas. The application of both techniques for complex device modification on VSLI devices fabricated with CMOS process technology is reviewed. (UK).
1996-12-31
Energy Technology Data Exchange (ETDEWEB)
The rate at which full-scale technology transfer takes place depends on the quality of the supply companies, i.e. training, organisational development and product infrastructure. These parameters are discussed for the example of a water mill, and a flow diagram is presented. [Deutsch] Wie rasch ein umfassender Transfer in Frage kommt, entscheidet sich mit der Qualitaet und dem Niveau der zuliefernden Betriebe. Hierbei sind Ausbildung, Organisationsentwicklung und Produktionsinfrastruktur besonders angesprochen. Fuer eine Wassermuehle werden diese Parameter konkret eroertert und an Durchlaufdiagrammen erlaeutert. (GL)
1997-12-31
Nuclear propulsion systems for orbit transfer based on the particle bed reactor
International Nuclear Information System (INIS)
The technology of nuclear direct propulsion orbit transfer systems based on the Particle Bed Reactor (PBR) is described. A 200 megawatt illustrative design is presented for LEO to GEO and other high #DELTA#V missions. The PBR-NOTV can be used in a one-way mode with the shuttle or an expendable launch vehicle, e.g., the Titan 34D7, or as a two-way reusable space tug. In the one-way mode, payload capacity is almost three times greater than that of chemical OTV's. PBR technology status is described and development needs outlined.
1987-01-12
Modeling of battery energy storage in the National Energy Modeling System
Energy Technology Data Exchange (ETDEWEB)
The National Energy Modeling System (NEMS) developed by the U.S. Department of Energy`s Energy Information Administration is a well-recognized model that is used to project the potential impact of new electric generation technologies. The NEMS model does not presently have the capability to model energy storage on the national grid. The scope of this study was to assess the feasibility of, and make recommendations for, the modeling of battery energy storage systems in the Electricity Market of the NEMS. Incorporating storage within the NEMS will allow the national benefits of storage technologies to be evaluated.
1997-12-01
Interview: Trevor Keel from the World Gold Council
British Library Electronic Table of Contents (United Kingdom)
Trevor Keel speaks to Cara Sutton, Assistant Commissioning Editor Within the World Gold Council's technology sector, Trevor Keel is responsible for a range of activities in relation to the development of new gold-based technologies. He has particular interest in the use of gold in the fields of medicine and diagnostics, catalysis and nanotechnology. Previously, Trevor was a principal chemist at GlaxoSmithKline where he was involved in numerous New Chemical Entity projects. Dr Keel has an extensive knowledge of nanotechnology, having completed a PhD in Pharmaceutical Nanotechnology at the University of Nottingham, Nottingham, UK.
2011-01-01
Interim explosives detection alternatives
Energy Technology Data Exchange (ETDEWEB)
There is a general concern with insiders smuggling bomb quantities of explosives into sensitive facilities such as nuclear facilities. At this time, there is no single explosives detection device that is suitable for monitoring personnel and their packages for explosives in an operational facility environment. However, there are techniques combining available commercial technologies with procedures and threat analysis that can significantly increase the insiders risk and reduce the population of adversaries. This paper describes the available applicable explosives detection technologies and discusses the techniques that could be implemented on an interim basis. It is important that these techniques be considered, so that some interim level of security against the explosives threat can be established until more sophisticated equipment that is under development becomes available.
1991-01-01
Energy Technology Data Exchange (ETDEWEB)
Focussed ion beam (FIB) technology has the advantage of being a maskless process compatible with UHV processing. This makes it attractive for use in in situ processing and has been applied to the fabrication of various mesoscopic structures. The present paper reviews these results whilst putting emphasis on in situ processing by a combined FIB and molecular beam epitaxy system. The typical performance of present FIB systems is also presented. In order to utilize the potential advantages of FIB processing, reduction of damage and improvement of throughput are important, and much effort has been devoted to developing processing techniques which require a reduced dose. The importance of low-energy FIB is discussed. (author).
1993-06-01
International Nuclear Information System (INIS)
Focussed ion beam (FIB) technology has the advantage of being a maskless process compatible with UHV processing. This makes it attractive for use in in situ processing and has been applied to the fabrication of various mesoscopic structures. The present paper reviews these results whilst putting emphasis on in situ processing by a combined FIB and molecular beam epitaxy system. The typical performance of present FIB systems is also presented. In order to utilize the potential advantages of FIB processing, reduction of damage and improvement of throughput are important, and much effort has been devoted to developing processing techniques which require a reduced dose. The importance of low-energy FIB is discussed. (author).
DARPA Fact File: A Compendium of DARPA Programs
In April 2002, the Defense Advanced Research Projects Agency (DARPA) released this overview of its current work. The report summarizes many of the organization's main programs, which are grouped into three broad areas. The first area details the efforts being made to minimize threats and ensure national security. Development of new technologies and advanced systems is highlighted in the second section, and the third looks at investigations into "high-risk, high-payoff technologies." There are numerous references to the war on terrorism that describe DARPA's involvement and specific projects to defend against terrorist acts.
2002-01-01
Technology management for heavy oil
Energy Technology Data Exchange (ETDEWEB)
The framework for investment in research and development (R&D) at a medium-sized Canadian petroleum company is described. The importance of R&D is illustrated by a graph showing the strong positive correlation between R&D intensity and sales for companies in the mainstream oil and gas sector in the USA. Strong R&D efforts also help to maintain market share and enhance corporate ability to transfer technology into its operations. Three ways of structuring, developing, and transferring technology are outlined: using in-house R&D facilities, which is too costly for medium-sized firms; having a central group responsible for funding third-party R&D, transferring technology into the company, and being aware of technology activities within and outside the company; and complete decentralizing of R&D, in which operations decides how, when, and ...
1994-12-31
Understanding renewable energy systems
Energy Technology Data Exchange (ETDEWEB)
Beginning with an overview of renewable energy sources including biomass, hydroelectricity, geothermal, tidal, wind and solar power, this book explores the fundamentals of different renewable energy systems. The main focus is on technologies with high development potential such as solar thermal systems, photovoltaics and wind power. This text not only describes technological aspects, but also deals consciously with problems of the energy industry. In this way, the topics are treated in a holistic manner, bringing together maths, engineering, climate studies and economics, and enabling readers to gain a broad understanding of renewable energy technologies and their potential. The book also contains a free CD-ROM resource, which includes a variety of specialist simulation software and detailed figures from the book. (Author)
2005-01-15
Status and progress in ion implantation technology for semiconductor device manufacturing
International Nuclear Information System (INIS)
Rapid growth in implant applications in the fabrication of semiconductors has encouraged a dramatic increase in the range of energies, beam currents and ion species used. The challenges of a wider energy range, higher beam currents, continued reduction in contamination, improved angle integrity and larger substrates have motivated the development of many innovations. Advanced processes in submicron device production uses up to twenty implantation steps. Thus the outstanding growth of this industry has led to the evolution of a thriving business of hundreds of implantation equipment systems each year with very specific requirements. The present paper reviews the principal process requirements which resulted in the evolution of the equipment technology, and describes the recent trends in the ion implanter technology all three principal categories: high current, medium current and high energy. (author)
1998-12-08
State-of-the-Art developments in accelerator controls at the APS.
Energy Technology Data Exchange (ETDEWEB)
The performance requirements of the Advanced Photon Source (APS) challenge the control system in a number of areas. This paper will review a few applications of advanced technology in the control and monitoring of the APS. The application of digital signal processors (DSPs) and techniques will be discussed, both from the perspective of a large distributed multiprocessor system and from that of embedded systems. In particular, two embedded applications will be highlighted, a beam position monitor processor and a DSP-based power supply controller. Fast data distribution is often a requirement. The application of a high-speed network based on reflective memory will also be discussed in the context of the APS global orbit feedback system. Timing systems provide opportunities to apply technologies such as high-speed logic and fiber optics. Examples of the use of these technologies will also be included. Finally, every modern ...
1999-04-13
Proceedings of the phytoremediation technical seminar
International Nuclear Information System (INIS)
The research and development efforts regarding phytoremediation technologies were the main focus of this conference. Phytoremediation is the term for any applied process that uses green plants and their associated microorganisms for remediating contaminated soils and groundwater. The 12 papers presented at this conference provided guidance on recommended requirements for the successful implementation of specific phytoremediation technologies. The mechanisms of phytoremediation for petroleum hydrocarbons were also described. Phytoremediation technologies are divided into two major classes including contaminant removal and contaminant stabilization. Several studies have shown that phytoremediation is effective in degrading, containing and transferring petroleum hydrocarbons in soil and groundwater. Phytoremediation has shown to hold promise for the effective and inexpensive cleanup of various hazardous ...
Energy Technology Data Exchange (ETDEWEB)
A set of nomographs to estimate the levelized energy cost for photovoltaic systems are presented. These are designed to assist system designers, analysts, and planners in estimating the effects of research and development and system-design optimization on the delivered cost of energy. The nomographs are based on a refined version of the energy cost estimation equation that appears in the National Photovoltaics Program Five-Year Research Plan. The nomographs have been prepared to emphasize technologies with the potential of producing low-cost energy (<$0.40/kWh levelized in nominal terms or $0.17/kWh in 1982 dollars), and thus primarily apply to far-term or advanced intermediate photovoltaic technologies. Separate sets of nomographs are presented to encompass both flat-plate and concentrator technologies. To supplement the nomographs, a set of tabular solutions of the energy cost equation are included ...
1984-12-31
Integrated optoelectronic materials and circuits for optical interconnects
International Nuclear Information System (INIS)
Conventional interconnect and switching technology is rapidly becoming a critical issue in the realization of systems using high speed silicon and GaAs based technologies. In recent years clock speeds and on-chip density for VLSI/VHSIC technology has made packaging these high speed chips extremely difficult. A strong case can be made for using optical interconnects for on-chip/on-wafer, chip-to-chip and board-to-board high speed communications. GaAs integrated optoelectronic circuits (IOC's) are being developed in a number of laboratories for performing Input/Output functions at all levels. In this paper integrated optoelectronic materials, electronics and optoelectronic devices are presented. IOC's are examined from the standpoint of what it takes to fabricate the devices and what performance can be expected.
Energy Technology Data Exchange (ETDEWEB)
This study presents a full cost approach to determine the levelized cost of energy (LCOE) of 14 electricity generation technologies. It encompasses costs incurred at all stages of the fuel cycle, including those that are traditionally omitted from economic evaluations of generation technologies. Incorporating these 'externalities' increases the likelihood of developing the most economical and sustainable power resource from a societal perspective. The following externalities are included in this analysis: damage from air pollution, energy security, transmission and distribution costs, and other environmental impacts. Incorporating externalities has a large impact on the LCOE and the relative attractiveness of electricity generation options. Results indicate that clean and efficient generation technologies are the most attractive when all options are examined using a full cost, ...
2002-12-01
Impact of developing technology on indirect liquefaction
Energy Technology Data Exchange (ETDEWEB)
The status of commercial technology for indirect liquefaction, as exemplified by SASOL facilities in South Africa, is reviewed. The impact of substituting more advanced gasifiers and synthesis systems is then investigated. Slagging BGC/Lurgi, Texaco and Shell-Koppers gasifiers were substituted for the Dry Ash Lurgi units used at SASOL. SASOL SYNTHOL synthesis units were replaced by slurry phase Fischer-Tropsch units employing technology pioneered by Kolbel. The advanced systems were found to have a highly favorable impact on plant efficiency, product distribution and gasoline cost. If all the projected technical improvements can be realized for indirect liquefaction, the yields of refined transportation fuels per ton of coal will approach those anticipated for direct liquefaction processes.
1980-11-01
Energy Technology Data Exchange (ETDEWEB)
The Buried Waste Integrated Demonstration (BWID) is a program of the Department of Energy (DOE) Office of Technology Development whose mission is to evaluate different new and existing technologies and determine how well they address DOE community waste remediation problems. Twenty-three Technical Task Plans (TTPs) have been identified to support this mission during FY-92; 10 of these have identified some support requirements when demonstrations take place. Section 1 of this report describes the tasks supported by BWID, determines if a technical demonstration is proposed, and if so, identifies the support requirements requested by the TTP Principal Investigators. Section 2 of this report is an evaluation identifying facility characteristics of existing Idaho National Engineering Laboratory (INEL) facilities that may be considered for use in BWID technology demonstration activities.
1992-04-01
Emerging trends in information and communication technology in mine safety and disaster management
British Library Electronic Table of Contents (United Kingdom)
There is tremendous growth in the use of Geographic Information Systems (GIS), Global Positioning Systems (GPS), Remote Sensing, Satellite Communication, and Modeling & Simulation techniques. These tools and techniques helps significantly in characterizing infrastructure, risk area and disaster zones, planning and implementation of hazards reduction measures etc. Communication satellites becomes vital for providing emergency communication and timely relief measures. Integration of space technology inputs into natural disaster monitoring and mitigation mechanisms is critical for hazard reduction. This paper mainly focused on all the issues described above. Major emphasis had been given to the recent developments in information & communication technology enabled tools and their applications ...
2010-01-01
Development of technology on the material surveillance of CANDU pressure tubes
International Nuclear Information System (INIS)
Material degradation of pressure tubes, which are the most important components in CANDU fuel channel, can only be evaluated by removing and examining them(material surveillance). This study aimed at establishment of overall evaluation technology including the evaluation of the material degradation for the integrity of pressure tubes of Wolsung units. Material tests for pressure tubes were performed as follows; (1) Evaluation on life limiting factors of pressure tubes (2) Review on leak-before-break and integrity maintenance technology of pressure tubes (3) Survey on selection criteria for tubes to be inspected and on related regulations for material surveillance (4) Analysis of material surveillance test procedure (5) Basic examinations of Wolsung unit 1 pressure tube material(TEM, texture, chemical component etc) (6) Manufacture of test equipments and test (DHCV, hydriding, grip and tensile specimen etc). 23 figs, 6 tabs, 59 refs. (Author).
1997-05-21
;Table of Contents: Legal authority; Summary of proposed regulations; Industry definition and waste streams; Industry description; Data and information gathering; Selection of pollutant parameters; Drilling wastes-characterization, control, and treatment technologies; Produced water-characterization, control, and treatment technologies; Miscellaneous waste-characterization, control, and treatment technologies; Cost and pollutant loading determination of drilling fluids and drill cuttings; Compliance cost and pollutant load determination of produced water; Compliance cost and pollutant load determination of well treatment, workover, and completion fluids; Cost and pollutant loading determination of deck drainage; Options selection-rationale and total costs; Pretreatment standards; Non-water quality environmental impacts and other factors; Best Management Practices; and Appendices.
1995-02-01
During 1978 the Engineering Board of SRC granted Specially Promoted Program status to the Coal Technology program. This recognized that coal would increase in importance as the cost of liquid and gaseous hydrocarbons rises with the decreasing availability of petroleum related sources. It was, therefore, considered necessary to anticipate and improve, through SRC supported research, the technologies required to win, transport, convert to liquid and gaseous fuels and utilize coal and coal based substances. In view of the interest in the program, and also in the hope of reaching a still wider audience the reports of the two meetings have been combined in this single booklet. The reports indicate specific problems of importance in coal winning and coal conversion but, naturally, do not cover all of the program priorities.
1980-10-01
A novel gamma scanning system for on-line diagnostic inspection of industrial process columns
International Nuclear Information System (INIS)
A computerised gamma scanning facilities for on-line investigation of industrial process columns and vessels has been developed by the Malaysian Nuclear Agency (Nuclear Malaysia). The technology, based on the principle of gamma-ray absorption, has been successfully applied for real-time troubleshooting, process investigation and predictive maintenance of a number of distillation columns and process vessels in petroleum refineries, gas processing plants and chemical plants in the country and the surrounding region. This paper outlines basic characteristics of the system and describes the inspection procedures, and in addition, presents a number of case studies. The case studies are purposely chosen to illustrate the versatility of the technology, and furthermore to demonstrate the economic benefits which can be realised from the application of this technology. (Author)
Keynote address. Division 1. Energy and economic development
Energy Technology Data Exchange (ETDEWEB)
This paper was presented at the opening plenary session. As the end of the century approaches, environmental protection is one of the most significant global issues which will shape our energy path and economic development pattern. In face of environmental challenges, we will have to take into account environmental factors in the economic development process itself. This requires the pursuit of sustainable economic development, a process which may involve strengthened energy conservation, improved efficiency and switching to less carbon intensive energy sources. Energy inefficiency, technological scarcity and financial vulnerability in developing countries may best be resolved by changing their economic and market structures to facilitate relevant investments. However, effective reform of the energy industry in developing economies and economies in transition ...
1995-12-31
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy`s Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional ...
1990-12-31
Development and testing of commercial-scale, coal-fired combustion systems, Phase 3
Energy Technology Data Exchange (ETDEWEB)
The US Department of Energy's Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over ...
1990-01-01
Future radioisotope power needs for missions to the solar system
Energy Technology Data Exchange (ETDEWEB)
NASA and DOE plan a cooperative team effort with industry, government laboratories and universities to develop a near term, low cost, low power (100 watt electric class), low mass (<10 kg), advanced radioisotope space power source (ARPS) and in the process reduce the plutonium-related costs as well. The near term is focused on developing an advanced energy converter to use with the General Purpose Heat Source (GPHS). The GPHS was developed and used for the current radioisotope thermoelectric generators (RTGs). Advanced energy converter technologies are needed as a more efficient replacement for the existing thermoelectric converters so that the space radioisotope power source mass and cost can be reduced. a more advanced technology space radioisotope power system program is also planned that addresses a longer-term need. Twenty first century robotic scientific information ...
1997-12-31
Energy Technology Data Exchange (ETDEWEB)
From 1991 to 1996, key studies on the reutilization, treatment, and disposal technology of hazardous wastes have been incorporated into the national plan for environmental protection science and technology. At present, the research achievements have been accomplished, have passed national approval, and have been accepted. The author of this paper, as leader of the national group for this research work, expounds the newest achievements of the studies involving four parts: (1) the reutilization technology of electroplating sludge, including the ion-exchange process for recovering the sludge and waste liquor for producing chromium tanning agent and extracting chromium and colloidal protein from tanning waste residue; on the recovery of heavy metals from the electroplating waste liquor with microbic purification; on the demonstration project of producing modified plastics from the sludge and the waste plastics; and on the ...
1996-12-31
International Nuclear Information System (INIS)
Various kinds of decontaminations are carried out in atomic power plant. Here current decontamination technologies such as chemical decontamination with chemical solution or blast decontamination have a problem of reduction of secondary radioactive waste generated in the decontamination process. On the other hand, a low pressure arc plasma can remove metal oxide film on the metal substrate without heavy damage on the metal substrate when the object to be treated was set as a cathode. Dry surface decontamination technology with using low-pressure arc plasma can decrease secondary radioactive waste because low-pressure arc plasma does not need any chemical solution. In addition, the time required for treatment can be shorter, so it is possible for the low-pressure arc plasma decontamination technology to interpolate the current decontamination technologies such as spot decontamination ...
2008-12-01
MILSTAR's flexible substrate solar array: Lessons learned, addendum
MILSTAR's Flexible Substrate Solar Array (FSSA) is an evolutionary development of the lightweight, flexible substrate design pioneered at Lockheed during the seventies. Many of the features of the design are related to the Solar Array Flight Experiment (SAFE), flown on STS-41D in 1984. FSSA development has created a substantial technology base for future flexible substrate solar arrays such as the array for the Space Station Freedom. Lessons learned during the development of the FSSA can and should be applied to the Freedom array and other future flexible substrate designs.
1990-01-01
Energy Technology Data Exchange (ETDEWEB)
The purpose of this project is to integrate a variety of geographic information systems capabilities and telecommunication technologies for potential use in geographic network and visualization applications. The specific technical goals of the project were to design, develop, and simulate the components of an audio/visual geographic communications system to aid future real-time monitoring, mapping and managing of transport vehicles. The system components of this feasibility study are collectively referred to as a Geographic Visualization and Communications System (GVCS). State-of-the-art techniques will be used and developed to allow both the vehicle operator and network manager to monitor the location and surrounding environment of a transport vehicle during shipment.
1998-03-30
Computer simulation and scientific visualization
Energy Technology Data Exchange (ETDEWEB)
The simulation of processes in engineering and the physical sciences has progressed rapidly over the last several years. With rapid developments in supercomputers, parallel processing, numerical algorithms and software, scientists and engineers are now positioned to quantitatively simulate systems requiring many billions of arithmetic operations. The need to understand and assimilate such massive amounts of data has been a driving force in the development of both hardware and software to create visual representations of the underling physical systems. In this paper, and the accompanying videotape, the evolution and development of the visualization process in scientific computing will be reviewed. Specific applications and associated imaging hardware and software technology illustrate both the computational needs and the evolving trends. 6 refs.
1990-01-01
Collective ion acceleration in systems with a virtual cathode
International Nuclear Information System (INIS)
The current status of research and development in the realm of physics and technology of collective ion acceleration in systems with a virtual cathode (VC) is reviewed. Three major acceleration methods and devices developed on their basis are considered: reflex triodes and their modifications, gas-filled vircators, and vacuum vircators with a Luce diode. Experimental data are outlined and the principal physical models interpreting these data are described. New ion acceleration techniques whose realization involves the production and disappearance of the VC are also discussed. All methods of collective ion acceleration are compared and the possible ways for the further development of this promising scientific field are highlighted. (reviews of topical problems)
2002-11-30
Australasia floating production storage offloading`s (F.P.S.O.) push
Energy Technology Data Exchange (ETDEWEB)
Floating Production, Offshore Storage and Offloading (FPSO) of hydrocarbons is not new. However, offshore crude oil development has to face the increasing need of the geopolitical interests to develop smaller or difficult reservoir in remote areas in deeper water and harsher environment. Such a trend can only be sustained if the offshore technology provides the right tools at the right time and at an acceptable price. This article will attempt to describe the relative merits of FPSO systems and discuss its main components. An overview of the present world situation shows the excellent performance of the FPSO with the type of development strategy undertaken in P.R.C.
1993-12-31
Transforming anaerobic digestion with the Model T of digesters
Energy Technology Data Exchange (ETDEWEB)
Most livestock farmers in the United States do not take advantage of anaerobic digester technology because of the high cost and large scale. These limitations therefore reduce the production of renewable energy from farmlands. In order to expand anaerobic digestion methods and improve environmental quality, affordable and smaller-scale digesters should be developed to enable most livestock farmers to convert manure to methane. Doing so would improve their economic efficiency and environmental sustainability. This paper provided an analogy to the development of the Model T to better explain the need and potential for this technology. A modified fixed-dome digester was installed on the Ohio State University dairy in Columbus, Ohio. The digester was unheated, buried, had a volume of 1 m{sup 3} and received diluted dairy manure as feedstock. Biogas was produced at digester temperatures as low 10 degrees C ...
2010-07-01
Energy Technology Data Exchange (ETDEWEB)
World-wide water scarcity, especially in the developing world, indicates a pressing need to develop inexpensive, decentralized small-scale desalination technologies which use renewable resources of energy. This paper provides a comprehensive review of the state-of-the-art in one of the most promising of these technologies, solar-driven humidification-dehumidification (HDH) desalination. Previous studies have investigated many different variations on the HDH cycle. In this paper, performance parameters which enable comparison of the various versions of the HDH cycle have been defined and evaluated. To better compare these cycles, each has been represented in psychometric coordinates. The principal components of the HDH system are also reviewed and compared, including the humidifier, solar heaters, and dehumidifiers. Particular attention is given to solar air heaters, for which design data is limited; and ...
2010-05-15
Task 27 -- Alaskan low-rank coal-water fuel demonstration project
Energy Technology Data Exchange (ETDEWEB)
Development of coal-water-fuel (CWF) technology has to-date been predicated on the use of high-rank bituminous coal only, and until now the high inherent moisture content of low-rank coal has precluded its use for CWF production. The unique feature of the Alaskan project is the integration of hot-water-drying (HWD) into CWF technology as a beneficiation process. Hot-water-drying is an EERC developed technology unavailable to the competition that allows the range of CWF feedstock to be extended to low-rank coals. The primary objective of the Alaskan Project, is to promote interest in the CWF marketplace by demonstrating the commercial viability of low-rank coal-water-fuel (LRCWF). While commercialization plans cannot be finalized until the implementation and results of the Alaskan LRCWF Project are known and evaluated, this report has been prepared to specifically address issues ...
1995-10-01
Small-satellite technology and applications III
Energy Technology Data Exchange (ETDEWEB)
This third conference on small-satellite applications has combined a number of significant and timely presentations on the status, in the US and on the international front, of this emerging industry. Presentations by all of the major Department of Defense activities in this field, including an overview of the ARPA CAMEO multispectral remote sensing satellite program, space activities at the Air Force Phillips Laboratory, and a space systems capabilities overview of the Naval Research Laboratory, are complemented by presentations from several international activities on their accomplishments and progress in the development of remote sensing satellite programs. For example: Spar Aerospace of Canada presented an overview of the progress they have made in establishing a space program through the use of small satellites, and the University of Surrey and Spar Aerospace provided an overview of the application of image compression schemes to imagery obtained from their ...
1993-01-01
Energy Technology Data Exchange (ETDEWEB)
The most recently developed control technologies in a hot strip mill are described. Preview AGC has been developed with a preview control synthesis. It controls roll gaps by using the previous information of disturbances. The disturbances which are concerned are derived from the rolling force, the roll gap and the thickness of a previous stand. The thickness accuracy and the availability of mill have been improved by this technology. An on-line roll grinding (ORG) system with an on-line roll profile meter (OPM) has been developed for the purpose of achieving schedule-free rolling. The ORG smooths the worn and roughed surface of a work roll and OPM can measure the profile of a revolving roll without contact. The data obtained by the OPM are given as feedback information to the ORG. As a result, grinding accuracy has been improved and rolling restriction on width has been relaxed ...
1999-12-01
EM-MWD technology; EM-MWD system jitsuyoka gijutsu
Energy Technology Data Exchange (ETDEWEB)
A project on the title is a special study of TRC (Technology Research Center) Japan National Oil Corporation, which aims at developing a system collecting many data near well bottom while drilling. The project is a 3-year project from 1993 to 1995 succeeding to results of a project on real-time drilling control technology which was finished in fiscal 1992. This paper is a record in fiscal 1993. In 1993, the first year, TRC starts a joint study with relational enterprises aiming at utilizing an EM-MWD (electromagnetic-measurement while drilling) system practically. Based on the past fruit of the study, the EM-MWD system was applied to an highly inclined well or a horizontal well. A total system was constructed, which improved electromagnetic radiation transmission efficiency, and reliability, and workability. An electromagnetic radiation receiver system for an offshore drilling rig was developed. A well ...
1994-10-31
Energy Technology Data Exchange (ETDEWEB)
A program is currently in progress at Argonne National Laboratory to evaluate and develop evaporator technology for concentrating radioactive waste streams. By concentrating radioactive waste streams, disposal costs can be significantly reduced. To effectively reduce the volume of waste, the evaporator must achieve high decontamination factors so that the distillate is sufficiently free of radioactive material. One technology that shows a great deal of potential for this application is being developed by LICON, Inc. In this program, Argonne plans to apply LICON`s evaporator designs to the processing of radioactive solutions. Concepts that need to be incorporated into the design of the evaporator include, criticality safety, remote operation and maintenance, and materials of construction. To design an effective process for concentrating waste streams, both solubility and vapor-liquid equilibrium data are ...
1993-10-01
Current issues of nuclear equipment standardization in Romania
International Nuclear Information System (INIS)
Standardization enhances: international cooperation; development of new nuclear techniques and technologies; characterization and checking procedures of equipment; sharing a common terminology. A historical sketch is given focussing: inception of standardization in electro-techniques at international scale; organization of the International Electrotechnical Commission, IEC; - current aspects of nuclear equipment standardization; activity of seven working groups devoted to nuclear reactor equipment; activity of seven groups working on radioprotection equipment; activity of four groups working on nuclear equipment. ISO organization and present issues concerning the nuclear technology development in Romania. It is presented the activity in the frame of CENELEC, CLC/TC45, for endorsing the IEC/TC45B standards. In 2007 a CENELEC/ BTT 127-1 working commission was formed to enhance assimilation of IEC /TC45 A ...
2009-10-12
Combining anatomy and function: the path to true image fusion
Energy Technology Data Exchange (ETDEWEB)
Modern imaging technologies visualize different aspects of disease in a non-invasive way. Considerable progress has been made in the fusion of images from different imaging modalities using software approaches. One goal of fusion software is to align anatomical and functional images and allow improved spatial localization of abnormalities. The resulting correlation of the anatomical and functional images may clarify the nature of the abnormality and help diagnose or stage the underlying disease. Whereas successful image fusion software has been developed for the brain, only limited success has been achieved for image alignment in other parts of the body. The development and current status of alternative approaches are presented. Dual-modality imaging is described with devices where two modalities are combined and mounted in a single gantry. The use of existing scanner technology ensures that no ...
2001-10-01
International Nuclear Information System (INIS)
Research and development and other activities of the various constituent units of Department of Atomic Energy (DAE) and also of the institution aided by DAE for the year 2005-2006 are reported. The various constituents units of DAE consist of nuclear research centres, nuclear power stations, fuel reprocessing and heavy water plants, nuclear fuel fabrication facilities, electronic and instrumentation production organisations, atomic mineral processing units and other nuclear installations. The activities of DAE cover the whole gamut of nuclear fuel cycle, research and development in nuclear science and reactor technology, applications of radiation and radioisotopes, radiation protection, research and development in front line areas such as robotics, lasers, mathematics and computational sciences. International research collaborations like CERN-DAE collaboration were completed by BARC. These activities ...
Analysis of international efforts in energy research and development
Energy Technology Data Exchange (ETDEWEB)
Research and experimental development comprise innovative and creative work undertaken systematically to increase the stock of knowledge of science, engineering, and society. This knowledge reserve is used to improve living conditions and standards, including economic growth. Research and development (R&D) expenditures are useful measures of the scale and direction of technological innovation within a country, industry, or scientific field. Administrators concerned with economic growth and performance rely on R&D statistics as one possible type of indicator of technological change. R&D statistics are an essential tool in many government programs and evaluations (OECD 1993). The objective of the analysis was to identify and evaluate R&D funding sources, levels, and trends in the energy sectors of selected industrialized countries (Australia, Belgium, Canada, Denmark, Finland, France, ...
1995-09-01
A hydrogen infrastructure - what, why, when and how - an oil industry perspective
International Nuclear Information System (INIS)
Shell Oil's exploration of profitable business opportunities afforded by fuel cells and by the emergence of a viable hydrogen economy is discussed. The emphasis in this paper is on the transportation sector, particularly the importance of a refueling infrastructure and the influence that consumer attitudes will have on which technological solution will gain the upper hand in hydrogen-powered vehicle development. Key issues facing the oil industry with regard to development of hydrogen as the new energy carrier are also reviewed. Methanol reformer fuel cell cars are the most likely to gain acceptability in the short term, but the probability of methanol fuel cell vehicles being replaced by gasoline or hydrogen fuelled fuel cell vehicles or be superseded by advances in internal combustion engine and after-treatment technology, are very real. Government regulations, fiscal incentives and societal pressures ...
1999-02-07
Proceedings. Future Energy - Resources, Distribution and Use
Energy Technology Data Exchange (ETDEWEB)
Leading abstract. The goals of the Norwegian Academy of Technological Sciences (NTVA) are to promote research, education and development within technological and related sciences, for the benefit of the Norwegian society and for the development of Norwegian industry. Future energy policy and Global climate change are major issues in the Norwegian discussion today. The answers given have great influence on our industry and involve huge technological challenges. In the current situation NTVA wishes to contribute to the development of new technology. In 1998 the Norwegian Academy of Technological Sciences organized the seminar ''Do We Understand Global Climate Change''. NTVA have now followed this up with a seminar on the Energy System, one of the major sources of manmade greenhouse ...
2001-07-01
Energy Technology Data Exchange (ETDEWEB)
The information gathered as operating manager when implementing the first photovoltaic rural electrification and technology transfer program carried out to date in the world in French Polynesia from 1978 to 1990 are detailed. The technical developments of equipment and the work in progress at the GENEC Cadarache within French, European or IEA programs in order to improve some components or appliances and make up for certain deficiencies are presented. This involves accelerated aging tests, Standardization work, development of high efficiency equipment. Non technical barriers are often emphasized. Technical barriers also exists. Considerable work in many domains of small PV systems remains to be done so as to combine all the conditions required to implement successful large programs in developed as well as in developing countries.
1994-12-31
DEFF Research Database (Denmark)
This article explores how action research, design based research and interaction design can be combined and used in the development of educational robotic tools. Our case study is the development of Number Blocks and it combines physical interaction, learning, and immediate feedback. Number Blocks supports the children's understanding of place value in the sense that it allows them to experiment with creating large numbers. The development was done in collaboration with a class of 7-8 year old children and their mathematics teacher. The article argues that elements from different research methods allowed a structured approach to projects that combines educational research and innovation of new learning technologies. Key elements of this approach is acknowledging the users input, developing a theoretical pre-analysis and using an iterative approach.
2011-01-01
Laboratory directed research and development program, FY 1996
Energy Technology Data Exchange (ETDEWEB)
The Ernest Orlando Lawrence Berkeley National Laboratory (Berkeley Lab) Laboratory Directed Research and Development Program FY 1996 report is compiled from annual reports submitted by principal investigators following the close of the fiscal year. This report describes the projects supported and summarizes their accomplishments. It constitutes a part of the Laboratory Directed Research and Development (LDRD) program planning and documentation process that includes an annual planning cycle, projection selection, implementation, and review. The Berkeley Lab LDRD program is a critical tool for directing the Laboratory`s forefront scientific research capabilities toward vital, excellent, and emerging scientific challenges. The program provides the resources for Berkeley Lab scientists to make rapid and significant contributions to critical national science and technology problems. The LDRD program also advances the ...
1997-02-01
Energy Technology Data Exchange (ETDEWEB)
With the November 1989 formation of the Office of Technology Development (OTD) within the Office of Environmental Restoration and Waste Management (EM) came the responsibility to develop programs to ensurethat enough trained and educated people would be available to support the achievement of EM's 30-year goal. This mission responsibility derives from public policy and Departmental environmental management requirements. Within DOE, urgency to move forward resulted from the assumptions (1) that the current workforce was insufficiently prepared for the transition from a production mission to a mission of environmental compliance and cleanup; and (2) that, given current trends and forecasts, the national education infrastructure was unlikely to yield the scientists, engineers, and technicians to meet future DOE workforce needs, especially in the case of women and minorities who, projected to make up two-thirds of the ...
1992-01-01
Development of swing-free / shock free crane
Energy Technology Data Exchange (ETDEWEB)
To develop the automatized crane and to apply the relevant technology to nuclear power plants, in this project and automatized crane control system is developed along with a swing and shock crane. Also, this technology has been transferred to Bando Machinery Co. Ltd. The drive mechanism of crane is designed by adopting vector drives which provide soft acceleration and deceleration characteristics. Also, radio modems and a long-range laser displacement sensor which are commercially available are introduced to accommodate the large scaled crane systems. Also, several devices are developed for the automation of crane system. These are a crane controller, a supervisory controller, a angle measuring device, and laser localizer, a drum grapple device, and crane supervisory program. The performance of developed crane system is revealed to rapidly reduce the residual ...
1999-04-01
User involvement competence for radical innovation
DEFF Research Database (Denmark)
One important market related capability for firms which seek to develop radical innovations is the competence to involve the 'right' users at the 'right' time in the 'right' form. While former studies have identified a rather passive role of users in the radical innovation process, this paper focuses on the involvement of such users that are in the position to play an active role as inventors and (co)-developers. A multiple case study analysis was conducted in the field of medical technology. Five radical innovation projects within four firms were selected including medical robots and computer-assisted navigation systems. The case study analysis reveals that firms who closely interact with specific users benefit significantly for their radical innovation work. These users have a high motivation toward new solutions, are open to new technologies, possess diverse competencies, and are embedded into a very ...
2007-01-01
British Library Electronic Table of Contents (United Kingdom)
Background:- Discrepancies exist in optometric education, practice and regulation across the Asia-Pacific region and the competence of optometric practitioners in adopting new lens technologies may vary widely. Over the past 10-years, a continuing professional development program, Varilux Academy Asia-Pacific (VAAP), was implemented and conducted in countries across the Asia-Pacific region to improve practitioners' understanding of optometric fitting principles, with special emphasis on progressive addition lenses (PAL). The aim was to demonstrate the effectiveness of VAAP and to compare the competence of practitioners across the Asia-Pacific region in new lens fitting technologies. Methods:- From 2002 to 2008, all VAAP participants from 12 countries across Asia-Pacific were invited to com...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
In the context of the special research area 561 (Thermally highly loaded, open-porous and cooled multi-layer systems for combined-cycle power stations), the actual technical and scientific realizations are to be extended and new scientific bases are to be created in order to realize total efficiencies of 65 %. In addition, innovative material solutions and new concepts must be compiled for the cooling and drainage. Under this aspect, the author of the contribution under consideration reports on the development of open-porous multi-layer systems for steam turbines of the 700 C technology. It results an efficiency potential of 12 % and a potential of 15 % with the reduction of CO{sub 2} in relation to the actual state of the art. Thereby, the potential of future combined-cycle power stations is not yet exhausted.
2008-07-01
The Triton project -- A North Sea subsea challenge
Energy Technology Data Exchange (ETDEWEB)
Three companies--Amerada Hess Ltd., Shell Expro (a 50/50 joint partnership between Shell and Esso) and Texaco--have joined forces in a project that will combine their expertise. The Triton project will allow three fields (Bittern, Guillemot West and Gullemot Northwest) to be developed simultaneously using subsea technology, with the wellheads on the seafloor and 68 miles (110 km) of flowlines taking oil and gas produced from the fields to a central floating production storage and offloading (FPSO) vessel. These fields are located in the central area of the North Sea, about 118 miles from Aberdeen in 295 ft of water. The paper discusses the development of the fields, subsea technology, technical challenges, laying the pipeline, and project completion.
1998-11-01
Legislation scrubs fluegas emissions
Energy Technology Data Exchange (ETDEWEB)
The article profiles developments in pollution control resulting from the strict emissions control standards due to be set by the European Commission in 1992. In particular technology to meet new emissions targets for mercury and dioxins is described. Control technologies covered included fixed-bed, direct injection, circulating fluidized bed and spray adsorption all of which use activated charcoal to absorb dioxin and mercury. Unfortunately activated charcoal processes still leave waste to be disposed of. Options include recycling the spent activated charcoal to the incinerator, vitrifying the activated charcoal and fly ash into a glassy unleachable substance and cracking the dioxins catalytically. It is hoped the developments will increase public acceptance of incineration. 4 figs., 1 tabs.
1992-06-01
Energy Technology Data Exchange (ETDEWEB)
This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The primary aim of this project is to obtain a basic scientific understanding of electrical transport processes at interfaces that contain an organic electronic material. Because of their processing advantages and the tunability of their electronic properties, organic electronic materials are revolutionizing major technological areas such as information display. We completed an investigation of the fundamental electronic excitation energies in the prototype conjugated polymer MEH-PPV. We completed a combined theoretical/experimental study of the energy relation between charged excitations in a conjugated polymer and the metal at a polymer/metal interface. We developed a theoretical model that explains injection currents at polymer/metal interfaces. We have made electrical ...
1999-06-04
FY 1992 Measurements and Characterization Branch annual report
Energy Technology Data Exchange (ETDEWEB)
The Measurements and Characterization Branch actively supports the advancement of DOE/NREL goals for the development and implementation of the solar photovoltaic (PV) technology. The primary focus of the laboratories is to provide state-of-the-art analytical capabilities for materials and device characterization and fabrication. The branch houses a comprehensive facility that Is capable of providing information on the full range of PV components. A major objective of the branch is to aggressively pursue collaborative research with other government laboratories, universities, and industrial firms for the advancement of Pv technologies. Members of the branch disseminate research findings to the technical community in publications and presentations. The Measurements and Characterization Branch encompasses seven coordinated research groups, providing integrated research and development that covers all ...
1993-03-01
Development of a robotics system for automated chemical analysis of sediment, sludges, and soils
International Nuclear Information System (INIS)
The introduction of automation technology into the analytical laboratory holds the promise of higher efficiency, improved productivity, and lower costs. However, the conventional ''laboratory robot'' widely used today may not offer the work envelope or reliability required in a high workload laboratory performing quality control or environmental analytical services. To address this need, a demonstration workcell was assembled utilizing an industrial-class robotics system to automate a standard EPA acid digestion protocol. With further development of graphical user interfaces and error recovery software, the technology will significantly enhance the ability of laboratories to meet increasingly complex environmental demands. 7 refs., 2 figs., 1 tab.
1989-11-26
Development of Head-end Pyrochemical Reduction Process for Advanced Oxide Fuels
Energy Technology Data Exchange (ETDEWEB)
The development of an electrolytic reduction technology for spent fuels in the form of oxide is of essence to introduce LWR SFs to a pyroprocessing. In this research, the technology was investigated to scale a reactor up, the electrochemical behaviors of FPs were studied to understand the process and a reaction rate data by using U{sub 3}O{sub 8} was obtained with a bench scale reactor. In a scale of 20 kgHM/batch reactor, U{sub 3}O{sub 8} and Simfuel were successfully reduced into metals. Electrochemical characteristics of LiBr, LiI and Li{sub 2}Se were measured in a bench scale reactor and an electrolytic reduction cell was modeled by a computational tool.
2008-12-15
Energy Technology Data Exchange (ETDEWEB)
Japanese companies have developed suitable cleansing technologies and export their know-how. Some original technologies are developed today, like: in-situ chemical oxidation, iron confinement, hot-soil process, low-temperature catalytic decomposition or dechlorination of dioxins. However, some pollutions are still poorly considered (nitrates) or badly mastered (dioxins). This situation is partly due to late legal decisions and to limited pollution abatement measures. Japan is also very active in bio-cleansing research, and this, despite the lack of dialogue and directives at the national level. Several research programs with important funds have started since 1995. However, Japan is still at the preliminary stage in open-field applications of cleansing methods. (J.S.)
1999-11-01
Capturing the Daylight Dividend
Energy Technology Data Exchange (ETDEWEB)
Capturing the Daylight Dividend conducted activities to build market demand for daylight as a means of improving indoor environmental quality, overcoming technological barriers to effective daylighting, and informing and assisting state and regional market transformation and resource acquisition program implementation efforts. The program clarified the benefits of daylight by examining whole building systems energy interactions between windows, lighting, heating, and air conditioning in daylit buildings, and daylighting's effect on the human circadian system and productivity. The project undertook work to advance photosensors, dimming systems, and ballasts, and provided technical training in specifying and operating daylighting controls in buildings. Future daylighting work is recommended in metric development, technology development, testing, training, education, and outreach.
2006-04-30
UNITED STATES DEPARTMENT OF ENERGY WASTE PROCESSING ANNUAL TECHNOLOGY DEVELOPMENT REPORT 2007
Energy Technology Data Exchange (ETDEWEB)
The Office of Environmental Management's (EM) Roadmap, U.S. Department of Energy--Office of Environmental Management Engineering & Technology Roadmap (Roadmap), defines the Department's intent to reduce the technical risk and uncertainty in its cleanup programs. The unique nature of many of the remaining facilities will require a strong and responsive engineering and technology program to improve worker and public safety, and reduce costs and environmental impacts while completing the cleanup program. The technical risks and uncertainties associated with cleanup program were identified through: (1) project risk assessments, (2) programmatic external technical reviews and technology readiness assessments, and (3) direct site input. In order to address these needs, the technical risks and uncertainties were compiled and divided into the program areas of: Waste Processing, Groundwater and Soil ...
2008-08-12
Which way forward : issues in developing an effective climate regime after 2012
International Nuclear Information System (INIS)
This book proposed that a post-2012 climate regime will need to balance the needs of all countries while aiming to prevent the potentially serious economic and social consequences of the impacts of climate change. Four elements were presented to support the emergence of an internationally acceptable approach: (1) the need to ensure sustainable economic development; (2) the effective development and penetration of clean technologies; (3) the establishment of an effective international carbon market over the long term; and (4) the integration of adaptation in development and natural resource management decision-making. A series of discussion papers were presented which reviewed options on how best to create an effective and inclusive international climate regime that will achieve large reductions in global emissions and equitably reflect the diverse circumstances of countries while promoting sustainable ...
Energy Technology Data Exchange (ETDEWEB)
In developing countries with rapidly growing economies, energy consumption will more than triple by 2030. This will require more than 8 trillion euros in investments in energy in these countries. The way these investments are made will be crucial in determining whether greenhouse gas emissions will rise proportionately. By creating a worldwide, lucrative market for clean technologies, countries can use the money they set aside for fighting climate change to stimulate large-scale private investment in clean energy production and efficient energy consumption. A well-functioning market ensures that money is invested where it will be the most cost-effective and will have the greatest impact in helping to solve a generally recognised problem. This also means making sure that innovations get to the market, so as to take advantage of economies of scale. The conference on 16 and 17 October 2006 in Amsterdam was the official start of the collaboration ...
2006-11-15
Energy Technology Data Exchange (ETDEWEB)
To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and ...
1998-03-01
Gas Storage Technology Consortium
Energy Technology Data Exchange (ETDEWEB)
The EMS Energy Institute at The Pennsylvania State University (Penn State) has managed the Gas Storage Technology Consortium (GSTC) since its inception in 2003. The GSTC infrastructure provided a means to accomplish industry-driven research and development designed to enhance the operational flexibility and deliverability of the nation's gas storage system, and provide a cost-effective, safe, and reliable supply of natural gas to meet domestic demand. The GSTC received base funding from the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL) Oil & Natural Gas Supply Program. The GSTC base funds were highly leveraged with industry funding for individual projects. Since its inception, the GSTC has engaged 67 members. The GSTC membership base was diverse, coming from 19 states, the District of Columbia, and Canada. The membership was comprised of natural gas storage field ...
2010-09-30
Technical considerations associated with waste-to-energy systems
Energy Technology Data Exchange (ETDEWEB)
The average American generates four pounds of solid waste per day, yet increasing constraints are being placed on the ability of municipalities to handle waste disposal. Most cities face a scarcity of acceptable landfill sites and conventional incineration and landfill methods have come under strict air, water and soil pollution standards. City administrators are being encouraged to select from a variety of proposed technologies that supplant traditional waste disposal methods, some of which offer the promise of revenues from energy and resource recovery. The problem is to select from available near-term technologies those systems that will fit into a city's long-term solid-waste management program. Broadly, waste-to-energy recovery systems now available to cities may be classified as combustion, pyrolysis, biodegradation, and mechanical front-end systems. It is important to notice that operations used for mechanical front-end systems ...
1981-01-01
Solar thermal electricity in 1998: An IEA/SolarPACES summary of status and future prospects
Energy Technology Data Exchange (ETDEWEB)
Research and development activities sponsored by countries within the International Energy Agency`s solar thermal working group. SolarPACES, have helped reduce the cost of solar thermal systems to one-fifth that of the early pilot plants. Continued technological improvements are currently being proven in next-generation demonstration plants. These advances, along with cost reductions made possible by scale-up to larger production and construction of a succession of power plants, have made solar thermal systems the lowest-cost solar energy in the world and promise cost-competitiveness with fossil-fuel plants in the future. Solar thermal technologies are appropriate for a wide range of applications, including dispatchable central-station power plants where they can meet peak-load to near-base-load needs of a utility, and distributed, modular power plants for both remote and grid-connected applications. In this paper, the ...
1998-07-01
Energy Technology Data Exchange (ETDEWEB)
As silicon-integrated circuit technology enters the sub-100 nm realm, continued progress will depend on a fundamental understanding of the physics of materials processing. The high cost of processing experimental lots and the speed at which new devices must be brought to the market have created a new emphasis on realistic physical models incorporated in technology CAD (TCAD) simulation tools. The volume bring together materials scientists, TCAD researchers and silicon technologists to review recent developments in the integrated-circuit community and to identify key issues for future research in this field. Results of research on the physical mechanisms involved in silicon device processing is presented both from experimental and theoretical viewpoints. The application of this fundamental research to TCAD process simulation models is also addressed. Topics include: shallow junctions and transient enhanced diffusion; ...
1998-07-01
Research on pressurised internally circulating fluidized bed boiler (PICFB)
Energy Technology Data Exchange (ETDEWEB)
In the atmospheric pressure coal combustion area, the internally circulating fluidized bed boiler (ICFB) has already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and los pollution characteristics. Cold model tests and computer simulation have been carried out to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the pressurized internally circulating fluidized bed boiler (PICFB). Based on the results achieved in this research, a hot-model design and fabrication ...
1995-12-31
Operation of pressurized internally circulating fluidized bed boiler (PICFB) 4MWth hot model
Energy Technology Data Exchange (ETDEWEB)
In the atmospheric pressure coal combustion area, the Internally Circulating Fluidized Bed Boiler (ICFB) had already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and because of its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and low-pollution characteristics. From fiscal 1992, the authors have conducted extensive research work, including cold model tests and computer simulations to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the Pressurized Internally Circulating Fluidized Bed Boiler (PICFB). Based on the ...
1997-12-01
International symposium on nuclear security. Book of extended synopses
International Nuclear Information System (INIS)
The International Symposium on Nuclear Security took place within a context of international acknowledgement that the threat of nuclear terrorism required dedicated action by the international community, States, industry and others. The Symposium dealt with those issues involved in protecting nuclear and other radioactive material from criminals. It also took place against a backdrop of renewed interest in nuclear technology: increased use of nuclear power, and increased use of radioactive isotopes in medicine and in industry. These are welcome developments, since nuclear energy and technology can indeed contribute to the technological and economic welfare of many countries, without compromising public health or the environment. In this context, security measures should not impede State programmes for peaceful use of nuclear technology. The symposium dealt with (1) the threat of ...
2003-11-05
A study on the planning to promote the advanced nuclear technology development project
Energy Technology Data Exchange (ETDEWEB)
Korea has participated in GIF from early stage, and played an important role in GIF as an original signatory of the GIF Charter. Korea has dispatched two representatives of GIF Policy Group and Expert Group respectively. Korea submitted 10 concepts of Gen IV for Gen IV technology roadmap. Korea's KALIMER and SMART concepts have stood higher in technological evaluation. 7 Korean experts were dispatched for Gen IV technology roadmap (4 from institution, 3 from industry and 1 form academia). Furthermore, USA's NTD (Near term Deployment) will be expanded to I-NTD (International NTD). This study suggested that Korea should propose APR-1400 as I-NTD concept for I-NTD discussion in GIF. Finally, Korea and USA jointly decided to fund 2 million dollars respectively for 2001 I-ERI program and selected 6 projects for the program, which are composed of 4 for LWR area and 2 for I and C area. 27 refs., 6 figs., 11 tabs. ...
2002-03-01
RAAN Conference. Support of Nuclear Power. Opening talk
International Nuclear Information System (INIS)
Nuclear power in Romania was initiated on the basis of CANDU reactor type technology, an option found to fulfill the requirements for a sustainable economic development, to support the electric energy demand of the country and to ensure the population and environment protection. The construction of the Cernavoda NPP was heavily based on the Romanian industry participation and basic and applied nuclear research national resources. The experience acquired from Cernavoda NPP Unit 1 will be fructified in the construction of Units 2-5 to be built. The Romanian Ministry of Education and Research implemented a nuclear national program for research and development taking into account the European Union requirements and recommendations, the cooperation with the IAEA - Vienna and the Romanian government policy on short and medium terms in the nuclear field. The research-development program targeted: the reactor ...
2002-09-06
Final report for SNL/NM environmental drilling project
Energy Technology Data Exchange (ETDEWEB)
Concern for the environment and cost reduction are driving forces for a broad effort in government and the private sector to develop new, more cost-effective technologies for characterizing, monitoring and remediating environmental sites. Secondary goals of the characterization, monitoring and remediation (CMR) activity are: minimize secondary waste generation, minimize site impact, protect water tables, and develop methods/strategies to apply new technologies. The Sandia National Laboratories (SNL) project in directional boring for CMR of waste sites with enhanced machinery from the underground utility installation industry was initiated in 1990. The project has tested a variety of prototype machinery and hardware built by the industrial partner, Charles Machine Works (CMW), and SNL at several sites (Savannah River Site (SRS), Hanford, SNL, Kirtland AFB (KAFB), CMW), successfully installed usable ...
1994-11-01
Enhancement of Heat and Mass Transfer in Mechanically Contstrained Ultra Thin Films
Energy Technology Data Exchange (ETDEWEB)
Oregon State University (OSU) and the Pacific Northwest National Laboratory (PNNL) were funded by the U.S. Department of Energy to conduct research focused on resolving the key technical issues that limited the deployment of efficient and extremely compact microtechnology based heat actuated absorption heat pumps and gas absorbers. Success in demonstrating these technologies will reduce the main barriers to the deployment of a technology that can significantly reduce energy consumption in the building, automotive and industrial sectors while providing a technology that can improve our ability to sequester CO{sub 2}. The proposed research cost $939,477. $539,477 of the proposed amount funded research conducted at OSU while the balance ($400,000) was used at PNNL. The project lasted 42 months and started in April 2001. Recent developments at the Pacific Northwest National Laboratory and Oregon State ...
2005-01-01
The role of clean coal technologies in post-2000 power generation
Energy Technology Data Exchange (ETDEWEB)
A substantial global market for advanced power systems is expected to develop early in the next century for both repowering and new capacity additions, Although natural gas-fueled systems, such as gas turbines, are expected to dominate in the 1990`s, coal-fueled systems are expected to emerge in the 2000`s as systems of choice for base-load capacity because of coal`s lower expected cost. Stringent environmental regulations dictate that all advanced power systems must be clean, economical, and efficient in order to meet both the environmental and economic performance criteria of the future. Recognizing these needs, the DOE strategy is to carry out an effective RD&D program, in partnership with the private sector, to demonstrate these technologies for commercial applications in the next century. These technologies are expected to capture a large portion of the future power generation market. The DOE: expects that, ...
1994-07-01
Energy Technology Data Exchange (ETDEWEB)
The Electrochemical Technology Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE`s Electric and Hybrid Propulsion Division (DOE-EHP). The goal of DOE-EHP is to advance promising electric-vehicle (EV) propulsion technologies to levels where industry will continue their commercial development and thereby significantly reduce petroleum consumption in the transportation sector of the economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R&D contracts on advanced battery technologies for DOE-EHP. This report summarizes the battery-related activities undertaken during the period of July 1, 1992 through September 30, 1992. In this report, the objective, background, technical progress, and status are described for ...
1992-12-31
The ANL Electrichemical Program for DOE on electric vehicle R D
Energy Technology Data Exchange (ETDEWEB)
The Electrochemical Technology Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE's Electric and Hybrid Propulsion Division (DOE-EHP). The goal of DOE-EHP is to advance promising electric-vehicle (EV) propulsion technologies to levels where industry will continue their commercial development and thereby significantly reduce petroleum consumption in the transportation sector of the economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R D contracts on advanced battery technologies for DOE-EHP. This report summarizes the battery-related activities undertaken during the period of July 1, 1992 through September 30, 1992. In this report, the objective, background, technical progress, and status are described ...
1992-01-01
Energy Technology Data Exchange (ETDEWEB)
This report summarizes the major activities conducted in the Chemical and Energy Research Section of the Chemical Technology Division (CTD) at Oak Ridge National Laboratory (ORNL) during the period January--March 1997. Created in March 1997 when the CTD Chemical Development and Energy Research sections were combined, the Chemical and Energy Research Section conducts basic and applied research and development in chemical engineering, applied chemistry, and bioprocessing, with an emphasis on energy-driven technologies and advanced chemical separations for nuclear and waste applications. The report describes the various tasks performed within seven major areas of research: Hot Cell Operations, Process Chemistry and Thermodynamics, Molten Salt Reactor Experiment (MSRE) Remediation Studies, Chemistry Research, Separations and Materials Synthesis, Solution Thermodynamics, and Biotechnology Research. The name ...
1998-01-01
Program plan for development of underground hydroelectric pumped storage technology
The Underground Hydroelectric Pumped Storage (UHPS) Program Plan describes in detail the planned activities and expected accomplishments in the conduct of UHPS technology development and validation envisioned in the 1976 to 1990 time frame. This document describes the program objectives, implementation strategy, and management methodology. The concept of underground hydroelectric pumped storage is fully directed to application in the electric utility industry. This technology involves using electrical energy generated by base-load plants during off-peak load periods to drive a high-head pump/turbine which pumps water from a lower reservoir to a substantially elevated (upper) reservoir corresponding to a head of 1000 m or so. The upper reservoir is at ground level and the lower reservoir is below ground. Then, during peak-load periods, water in the upper reservoir is allowed to flow to the lower reservoir which, in turn, ...
1976-03-01
International Nuclear Information System (INIS)
This conference and trade show provided a forum to present new, emerging and existing technologies that will play a key role in ensuring that hydrocarbon exploitation occurs in a sustainable manner, where costs and resource recovery are optimized while minimizing environmental impacts. The challenge of developing maturing basins, frontier lands and unconventional resources was discussed. In particular, the application of thermal recovery methods such as steam assisted gravity drainage (SAGD) for the in-situ recovery of heavy oils and bitumens was reviewed and compared with the performance of alternative enhanced energy recovery technologies such as vapor extraction (VAPEX). The conference was attended by local and international participants in the petroleum sector, including managers, engineers, technologists, geologists, and other petroleum industry specialists. The conference featured 132 presentations addressing topics ...
2007-06-12
Development of fission Mo-99 production technology
Energy Technology Data Exchange (ETDEWEB)
This R and D project is planed to supply domestic demands of Mo-99 through fission route, and consequently this project will be expected to rise up utilization of HANARO and KAERI's capability for marketing extension into domestic and oversea radiopharmaceutical market. HEU and LEU target types are decided and designed for fission Mo-99 production in domestic. Experimental study of target fabrication technology was performed and developed processing equipments. And conceptual design of target loading/unloading in/from HANARO device are performed. Tracer test of Mo-99 separation and purification process was performed, test results reach to Mo-99 recovery yield above 80% and decontamination factor above 1600. Combined Mo-99 separation and purification process was decided for hot test scheduled from next year, and performance test was performed. Conceptual design for modification of existing hot cell for fission Mo-99 production facility ...
2001-05-01
An optimization study on PEFC drive electric vehicle
Energy Technology Data Exchange (ETDEWEB)
Efforts have been made to develop fuel cell powered EVs (electric vehicles) in several countries and to demonstrate its high potential. Since 1990 fuel cell research has been conducted at FUT (the Fukui University of Technology) beginning with PAFC. Research effort is now being focused upon the application of fuel cells to the EV drive as this technology shows great future potential, particularly in the area concerning environmental protection. PEFC (Polymer Electrolyte Fuel Cell) has been chosen as the fuel cell for the EV power source because it possesses an inherent high power density and it also has another important feature; operation can be started under ambient temperature without preheating. The principal objective of this research is to pursue the optimum system of a PEFC drive EV. The size of the prototype vehicle in the university project is limited to a certain range and the capacity of the PEFG stack is also ...
1996-12-31
AP1000 plant construction in China: Ansaldo Nucleare contribution
International Nuclear Information System (INIS)
On 24th of July 2007 Westinghouse Electric Co. signed landmark contracts with China's State Nuclear Power Technology Corporation (SNPTC), to provide four AP1000 nuclear power plants in China. The AP1000 is a two-loop 1117 MWe Pressurized Water Reactor (PWR). It is based on proven technology, but with an emphasis on safety features that rely on natural driving forces, such as pressurized gas, gravity flow, natural circulation flow and convection. Ansaldo Nucleare has provided a significant support to the passive plant technology development and, starting from 2000, is cooperating with Westinghouse to development of the AP1000 Plant. In the frame of the AP1000 Chinese agreement, Ansaldo Nucleare, in Joint Venture with Mangiarotti Nuclear, has signed a contract with Westinghouse for the design and the supply of innovative components to be installed in the first AP1000 unit to be ...
2009-10-12
...Events Archive Worldwide Africa Programme Arab Programme Asia and Pacific Programme Europe and NIS Programme Latin American and Caribbean Programme Least-Developed Countries South-South Cooperation Human Security Directory of Offices Research & Statistics Publications Research and Statistics Subsites Annual Report Evaluation Group Investment and Technology Promotion Policymaking Organs Legal Resources Goodwill Ambassadors Industrial Competitiveness and Trade Private Sector Development Environmental Management Energy and Climate Change Research and Statistics Financial Institutions Partnerships Thematic ...Events Archive Worldwide Africa Programme Arab Programme Asia and Pacific Programme Europe and NIS Programme Latin American and Caribbean Programme Least-Developed Countries South-South Cooperation Human Security Directory of Offices Research & Statistics Publications Research and Statistics ...
Training guidelines in non-destructive testing techniques. 2002 edition
International Nuclear Information System (INIS)
Non-destructive testing (NDT) is a dynamic technology and progresses with time. Since the issuance of IAEA-TECDOC-628 in 1991, the technology has experienced numerous changes. Advancements in knowledge about the behaviour of materials have led to changes in the applicable NDT codes, standards and specifications. In addition, over the last ten years, as a result of extensive research and development activities worldwide, new NDT techniques and equipment have been developed which are accepted by engineering community. To accommodate the latest developments, modifications are required to training materials. The present publication is an updated version of IAEA-TECDOC-628. The modifications were made during an Advisory Group Meeting, held in Vienna from 25-29 June 2001. The content of the first edition of IAEA-TECDOC-628 has been revised based on the experience of the experts, as well ...
1986-09-21
The vital importance of GIS : a workshop in project siting and development
Energy Technology Data Exchange (ETDEWEB)
Geographic information system (GIS) technology is now being used by wind energy developers who are required to consider and accommodate a wide variety of environmental and social considerations. This poster presentation discussed some of the new features available in current GIS technologies. High resolution imagery from satellites is being used to verify the accuracy of collected spatial data, as well as to investigate potential locations for meteorological towers, turbine sites, and roads. Slopes are easily calculated using GIS software tools, and digital elevation data can be used with high resolution aerial photography to determine routes for new roads and to establish available sites for crane pads. The GIS tools allow developers to consider protected ecological areas, wetlands and forests, and gives them the ability to better report project development considerations at public ...
2010-07-01
The 4th international colloquium on process simulation. Proceedings
Energy Technology Data Exchange (ETDEWEB)
The papers collected in this volume were presented at the 4th Colloquium on Process Simulation held at Helsinki University of Technology, Espoo, Finland, June 11-13, 1997. In the more developed industrial nations, the processes for producing chemicals, energy, and materials encounter environmental concern and laws which challenge engineers to develop the processes towards more efficient, economical and safe operation. This necessitates more thorough understanding of the processes and phenomena involved. Formerly, the development of the processes was largely based on trial and error, whereas today, the development of computer performance together with the diversification of modelling software enables simulation of the processes. The increased capacity and possibilities for modelling the processes brought by the improved hardware and software, have generated a strong demand for more ...
1997-12-31
Technical review, Vol. 29, No. 3, Ser. No. 85, October 1992
Energy Technology Data Exchange (ETDEWEB)
Contents: expansion of pc mill application to plate mill and tandem cold mill; application of cluster type rolling mill (cr mill) for rolling of special steel (illustration); development of on-line roll grinding system with profile meter; development of new type jet pickling; new technology in continuous annealing furnace (illustration); anti-seismic testing system by 3-dimensional shaking table; development of mitsubishi hybrid desulfurization system; field performance of 500 mw advanced coal fired supercritical pressure operation boiler for unit no. 1 of tsuruga thermal power station, hokuriku electric power co., inc.; development of electronically controlled cylinder liner lubrication system for marine diesel engines; prediction technology on steady-state and transient performance of multi-air conditioners; a knowledge-based system approach to the autonomous ...
1992-01-01
Solid waste research and development: A perspective from Pacific Northwest Laboratory
Energy Technology Data Exchange (ETDEWEB)
The need for research and development (R&D) of technologies and approaches for sound, effective solid waste management is unquestionable. While many advances have been made by the government and private sectors, still more are needed. Resources for conducting R&D, even at the federal level, are limited however, and thus it is critical that resources be distributed as wisely as possible. The US Department of Energy has a vested interest in developing technologies and approaches for managing solid waste because solid waste management is strongly linked to energy use and environmental impacts. This federal role is needed to address the national and international impacts that can result from the cumulative effects of decisions being made at local, county, state, and regional levels. At Pacific Northwest Laboratory (PNL), one of DOE`s R&D laboratories, we are developing an ...
1992-11-01
On appraising alternative power plant investment proposals. Pt. 1: The economic model
Energy Technology Data Exchange (ETDEWEB)
Combined energy plants operating on the Brayton-Rankine cycle have gained wide acceptance as the most efficient energy conversion system. The technology is well proven and numerous research activities are underway to develop it further past its present plateau of performance. In developed and emerging economies alike, the current situation in the global economic market has caused the liberalisation of the energy industry in some countries, and in others it is causing a rethink of economic and energy policies. A result is that electric utility companies that have enjoyed a monopoly in power generation and distribution are seeing this privilege being eroded. This is opening up opportunities for independent power production and, consequently, for gas/steam turbine plants because of the technical merits of the technology and its ability to fill the vacuum being created in the energy industry. An economic ...
2000-12-01
Energy Technology Data Exchange (ETDEWEB)
The industrial policy of fine ceramics which is one of the new material expected to solve energy/environmental problem, is described. Fine ceramics are possessed with the characteristics like surpassing electromagnetic properties, heat resistance, high strength, etc. and its use as highly efficient power generation plant material, functional material for various sensors/electronic, and activation of existing industries are cited. As for the reclamation of global environment, promotion of saving energy in a global scale, development of innovative environmental technology and increase of carbon dioxide absorption source are described. Furthermore, research and development work in Japan on global environmental industrial technology for 1992 to 1993, new sunshine project and technical developments relating to fine ceramics are explained. As for the results of research and ...
1993-04-01
Development of high power negative ion sources for fusion at JAERI
Energy Technology Data Exchange (ETDEWEB)
Technologies producing high power negative ion beams have been highly developed in these years at JAERI for use in neutral beam injectors for heating the thermonuclear fusion plasmas. At present, it is possible to produce multi-ampere H-/D- ion beams quasi-continuously at energies more than a few hundred keV with a good beam optics of beamlet divergence of a few milli-radian. Based on these technologies, two R and D projects have been initiated; one is to develop a 22A/500keV/10s D- ion source for the neutral beam injector for JT-60U, and the other is to develop a 1A/1MeV/60s H- ion source to demonstrate high current negative ion acceleration up to the energy of 1MeV, the energy required for the neutral beam injector for International Thermonuclear Experimental Reactor (ITER). (author).
1995-10-01
Coal liquefaction: A research and development needs assessment: Final report, Volume I
Energy Technology Data Exchange (ETDEWEB)
The DOE Coal Liquefaction Research Needs (COLIRN) Panel reviewed, developed, and assessed R and D needs for the development of coal liquefaction for the production of transportation fuels. Technical, economics, and environmental considerations were important components of the panel's deliberations. The panel examined in some depth each of the following technologies: direct liquefaction of coal, indirect liquefaction via conversion of coal-derived synthesis gas, pyrolysis, coprocessing of combined coal/oil feedstocks, and bioconversion of coal and coal-derived materials. In this assessment particular attention was given to highlighting the fundamental and applied research which has revealed new and improved liquefaction mechanisms, the potentially promising innovative processes currently emerging, and the technological and engineering improvements necessary for significant cost reductions. As ...
1989-03-01
Cars and fuels for tomorrow: A comparative assessment
International Nuclear Information System (INIS)
Light duty vehicles, i.e. passenger cars and light trucks, account for approximately half of global transportation energy demand and, thus, a major share of carbon dioxide and other emissions from the transport sector. Energy consumption in the transport sector is expected to grow in the future, especially in developing countries. Cars with alternative powertrains to internal combustion engines (notably battery, hybrid and fuel-cell powertrains), in combination with potentially low carbon electricity or alternative fuels (notably hydrogen and methanol), can reduce energy demand by at least 50%, and carbon dioxide and regulated emissions much further. This article presents a comparative technical and economic assessment of promising future fuel/vehicle combinations. There are several promising technologies but no obvious winners. However, the electric drivetrain is a common denominator in the alternative powertrains and continued cost reductions ...
2001-05-01
Energy Technology Data Exchange (ETDEWEB)
In the framework of the renewable energies development policy and the energy mastership wanted by the Government, a document has been asked by the Prime Minister. It evaluates the development prospects at long and medium dated, of the main chains of renewable energies production taking into account the national developable deposits size, the technologies assessment, the environmental impacts and the competition facing the traditional energies. It evaluates the measures leading to an increasing efficiency. Measures concerning the regulations, the budget, and the fiscality are also discussed. From these analysis, a national strategy for actions in favor the renewable energies, are proposed. (A.L.B.)
2000-09-01
Plan for addressing issues relating to oil shale plant siting
Energy Technology Data Exchange (ETDEWEB)
The Western Research Institute plan for addressing oil shale plant siting methodology calls for identifying the available resources such as oil shale, water, topography and transportation, and human resources. Restrictions on development are addressed: land ownership, land use, water rights, environment, socioeconomics, culture, health and safety, and other institutional restrictions. Descriptions of the technologies for development of oil shale resources are included. The impacts of oil shale development on the environment, socioeconomic structure, water availability, and other conditions are discussed. Finally, the Western Research Institute plan proposes to integrate these topics to develop a flow chart for oil shale plant siting. Western Research Institute has (1) identified relative topics for shale oil plant siting, (2) surveyed both published and unpublished information, and ...
1987-09-01
British Library Electronic Table of Contents (United Kingdom)
In an environment of rapid technological change, countries in the developed and developing worlds need to improve the population's skills and competences. Since 1992, education reforms and various education sector documents and policy frameworks have been implemented to improve quality of education by getting more children into school through the abolishing of school fees, and the school feeding programme, whilst special efforts are made to deal with issues of gender inequality and the empowerment of women to meet the goals of Education for All and the education-related Millennium Development Goals 2 and 3. Though gains have been made in the area of gross enrolment ratio, there are still gross disparities in net enrolment and completion rates at regional level, with girls lagging behind bo...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Onshore pipelines have traditionally been designed with a deterministic stress based methodology. The changing operating environment has however imposed many challenges to the pipeline industry, including heightened public awareness of risk, more challenging natural hazards and increased economic competitiveness. To meet the societal expectation of pipeline safety and enhance the competitiveness of the pipeline industry, significant efforts have been spent for the development of reliability-based design and assessment (RBDA) methodology. This paper will briefly review the technology development in the RBDA area and the focus will be on the progresses in the past years in standard development within the American Society of Mechanical Engineers (ASME) and the Canadian Standard Association (CSA) organizations. (author)
2005-07-01
International Nuclear Information System (INIS)
The objective of this project is to develop multi-dimensional computational models in order to improve the operation of uranium electrorefiners currently used in pyroprocessing technology. These 2-D (US) and 3-D (ROK) mathematical models are based on the fundamental physical and chemical properties of the electrorefiner processes. The validated models by compiled and evaluated experimental data could provide better information for developing advanced electrorefiners for uranium recovery. The research results in this period are as follows: - Successfully assessed a common computational platform for the modeling work and identify spatial characterization requirements. - Successfully developed a 3-D electro-fluid dynamic electrorefiner model. - Successfully validated and benchmarked the two multi-dimensional models with compiled experimental data sets
2008-08-01
British Library Electronic Table of Contents (United Kingdom)
Customer relationships, product development, data integration and demand-driven supply chains are key concepts for companies that wish to remain competitive in today?s global economy. To address this important information management issue, the present study examines how, within a demand-driven network context, an eCRM can influence the interorganizational product development process between a manufacturer and its key customers. The theoretical model, built on research related to a technology assimilation model based on Fichman?s (2000) work, was tested on data from 104 manufacturers in the wireless equipment sector. The results show that the adoption of an eCRM does not moderate the relationship between collaborative e-product development involving a manufacturer and its key customers and ...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.
1991-12-01
Energy Technology Data Exchange (ETDEWEB)
Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.
1991-12-01
Extensions to the energy system GMM model: An overview
International Nuclear Information System (INIS)
This report describes recent extensions to the energy-systems GMM (Global Multiregional MARKAL) model undertaken by the Energy Economics Group (EEG) of the Paul Scherrer Institute (PSI) in Switzerland (hereon referred to as PSI-EEG) in the context of the SAPIENTIA project sponsored by the European Commission (DG Research) and the Swiss National Centre for Competence in Research on Climate (NCCR-Climate). GMM is a multi-regional 'bottom-up' energy-systems optimization model that endogenizes technology learning. The model has been developed and is used at PSI-EEG. The main extensions undertaken here concern the incorporation of a clusters approach to technology learning, the introduction of an improved representation of the transportation sector with emphasis on the passenger sub-sector and the implementation of marginal abatement curves for CH4 and N2O, two main non-CO2 greenhouse gases. Also, a linear representation of the ...
2005-06-12
The national nuclear material tracking system. A Korea's countermeasure against nuclear terrorism
International Nuclear Information System (INIS)
Since nuclear terrorism has been identified as a real threat, the Korean government has earnestly developed elementary technologies and sub-systems for establishing an integrated defensive system against nuclear terrorism, which is based on the concept of defense-in-depth. This paper introduces the gist and implications of the studies that have been conducted in building the national nuclear material tracking system for preventing and intercepting the illicit trafficking and transporting of nuclear material in Korea. (orig.)
2011-07-01
The high-temperature reactor's attractiveness lies in passive safety
International Nuclear Information System (INIS)
In the recent years the use of nuclear energy has turned from a technical and scientific issue to a political one. The high-temperature reactor (HTR) however, has always been advertised as particularly safe. The present situation and future developments of HTR-technology were the two issues that VDI-News brought up on the 27th October on an HTR-conference in an interview with the 'spiritual father' of the HTR, Prof. Dr. Rudolf Schulten of the Juelich Nuclear Research Centre. (orig.).
Summary of Initial Testing of SuperLig 644 at the TFL Ion Exchange Facility
Energy Technology Data Exchange (ETDEWEB)
Research at the Savannah River Technology Center aided development of a technical design basis for a Waste Treatment Plant (WTP) to pre-treat and vitrify Hanford tank waste as part of the River Protection Project (RPP). The research addresses safety concerns, process optimization, and waste form compliance. This program will provide technical data to ensure that the process functions as it was designed and minimizes costs.
2001-04-17
Steam turbine-service. Upgrading the low-pressure steam turbines in the Emsland nuclear power plant
International Nuclear Information System (INIS)
A century of technical development put steam turbines on a high level regarding efficiency and reliability. This procedure is still ongoing. The technological-commercial point of view - influenced intensively by liberalisation of the energy-market - makes great demands on field services. Well suited concepts in service and modernization are the solutions, as shown in NPP Emsland upgrade.
Review of nuclear energy; Ydinenergian tilannekatsaus
Energy Technology Data Exchange (ETDEWEB)
The report is an overview on the production of the nuclear energy all over the world. The amount of production at present and in future, availability of the nuclear fuel, development of nuclear technology, environmental and safety issues, radioactive waste management and commissioning of the plants and also the competitivity of nuclear energy compared with other energy forms are considered. (91 refs.).
1997-05-01
Radiation facility with electron accelerator of the Institute for Nuclear Research of Ukraine, Kiev
International Nuclear Information System (INIS)
Characteristics of the Ukrainian NSA NRI radiation facility for scientific researches and developments of industrial radiation technology are performed. Parts of the facility, design peculiarities of technical tools are described. Biological protection of the facility and radiation protection system, transport line, systems of technical provision and radiation measurements are discussed
2003-02-01
Energy Technology Data Exchange (ETDEWEB)
The document, based on European guidelines, was jointly developed by radiation oncologists, radiation physicists and radiation technologists. It contains the aims of the guidelines, professional profiles, roles and responsibilities, personnel and equipment requirements, procedures.
1996-12-01
Energy Technology Data Exchange (ETDEWEB)
Since 1985 the operating sections of the 1200 kV AC Ekibastuz-Urals transmission system were used for a variety of field studies on a wide range of technological problems associated to high voltage transmission lines. The tests performed confirmed correctness of the main engineering and design decision made at development stage and demonstrated that such transmission lines are reliable and efficient. 3 figs.
1989-12-31
PFB coal fired combined cycle development program. System analyses and trade-offs (Task 1. 3)
Energy Technology Data Exchange (ETDEWEB)
The systems analyses and optimization studies performed in connection with a program to design and evaluate a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion and advanced technology in the hot gas cleanup system and gas turbines are presented. Details on the plant control system are included. (LCL)
1981-02-01
PFB coal fired combined cycle development program. Final report
Energy Technology Data Exchange (ETDEWEB)
A final report is presented on the design, environmental characteristics, performance and maintainability, and economic analysis of a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion, and advanced technology in the hot gas cleanup system and gas turbines. Experimental data on the performance of each of the major components are included. (LCL)
1981-03-01
Nuclear methods monitor nutrition
International Nuclear Information System (INIS)
Neutron activation of nitrogen and hydrogen in the body, the isotope dilution technique and the measurement of naturally radioactive potassium in the body are among the new nuclear methods, now under collaborative development by the Australian Nuclear Scientific and Technology Organization and medical specialists from several Sydney hospitals. These methods allow medical specialists to monitor the patient's response to various diets and dietary treatments in cases of cystic fibrosis, anorexia nervosa, long-term surgical trauma, renal diseases and AIDS. ills.
Kinetic energy accumulators. Application to electric cars
Energy Technology Data Exchange (ETDEWEB)
The development of electric cars always met with the difficulty in storing energy and in recovering it in the form of electric power. Research work done for the last two decades in the field of materials and of new technologies oriented mainly towards aeronautical and space applications have led to designing, realizing and experimenting with flywheels rotating at high speed in magnetic bearings. The results obtained represent openings that, now, fall in with different industrial fields and in particular with application to electric cars.
1982-12-01
Introduction to the special issue on decision support in medicine
British Library Electronic Table of Contents (United Kingdom)
Information technology plays an important role in medicine because of the advanced decision support systems (DSS) it can provide. We provide an overview of the building blocks necessary for a medical decision support system and introduce seven research articles in this special issue that describe the development and evaluation of individual medical DSS building blocks or complete medical DSS.
2007-01-01
International Nuclear Information System (INIS)
In response to severe maintenance problems caused by the highly corrosive toxic and radioactive substance used in the nuclear reprocessing industry, AEA Technology (formerly the United Kingdom Atomic Energy Authority) has developed a series of power fluidics devices with no moving parts. These maintenance-free devices are described in this article which also explores applications in fields outside their original brief. (UK).
...and supply ensuring better food quality for the consumer developing safer and more flexible food production processes and technologies raw materials for food production; production and processing systems; by-products and wastes from fisheries and agro-industry; new food sources; packaging systems; quality monitoring; traceability Food contamination detecting and eliminating infectious and toxic agents throughout the food chain establishing the hazards and origins of food contaminants producing food more safely rapid ...
Energy Technology Data Exchange (ETDEWEB)
Heat transfer has emerged as a leading-edge technology supporting the rapid pace of developments in science and engineering ranging from energy production to electronic cooling. Subjects covered at the 6th UK National Conference on heat transfer held at Edinburgh from 15-16 September 1999 include: convection; boiling and evaporation; condensation; numerical techniques; heat exchangers; radiation and combustion; conduction; two-phase flow and heat transfer augmentation. Fifteen of the papers are abstracted here.
1999-07-01
Geothermal heat pumps - gaining ground in the UK and worldwide
Energy Technology Data Exchange (ETDEWEB)
This 2001 edition of the guide to UK renewable energy companies examines the geothermal heat pump sector, and discusses the technology involved, installations of geothermal heat pumps, the activity in the UK market with increased interest in UK geothermal heat pump products from abroad, and developments in the building sector. The UK government's increased support for the industry including its sponsorship of the Affordable Warmth programme, and the future potential of ground source systems are discussed.
2001-07-01
Geothermal heat pumps - gaining ground in the UK and worldwide
International Nuclear Information System (INIS)
This 2001 edition of the guide to UK renewable energy companies examines the geothermal heat pump sector, and discusses the technology involved, installations of geothermal heat pumps, the activity in the UK market with increased interest in UK geothermal heat pump products from abroad, and developments in the building sector. The UK government's increased support for the industry including its sponsorship of the Affordable Warmth programme, and the future potential of ground source systems are discussed.
First tests of "bulk" MICROMEGAS with resistive cathode mesh
We present the first results from tests of a MICROMEGAS detector manufactured using the so-called "bulk" technology and having a resistive cathode mesh instead of the conventional metallic one. This detector operates as usual MICROMEGAS, but in the case of sparks, which may appear at high gas gains, the resistive mesh reduces their current and makes the sparks harmless. This approach could be complementary to the ongoing efforts of various groups to develop spark-protected MICROMEGAS with resistive anode planes.
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
This paper illustrates how the techniques developed by the authors for capital cost targeting of mass exchange networks can be applied to determination of capital investment targets for reduction in effluent for existing systems involving mass exchange. The results is an impact diagram which shows the relationship between effluent reduction and capital investment, indicating a region of limiting return on investment as well as the maximum possible reduction in effluent. (au)
1999-02-01
Dust and waterfree technology for demolition works in nuclear environments and other sensitive areas
International Nuclear Information System (INIS)
At the University of Karlsruhe experiments were carried out from 1997 to 1999 to get fundamentals of flow characteristics of pneumatic extracted materials. The results could be used to develop a concept for demolition suitable for extraction and removing high-density concrete. The concept fulfills all demands of a closed nuclear area, especially of dust abatement. (orig.)
Drying of medicinal plants with solar energy utilization
Energy Technology Data Exchange (ETDEWEB)
In the paper, a potential of solar energy for drying of medicinal plants in Polish conditions is estimated and development of solar drying technologies is presented. The results of economic assessment of flat-plate solar collectors applied for drying of medicinal plants on a farm are promising. In some specific conditions, e.g. drying of wild grown medicinal plants in remote areas, even application of photovoltaic modules for driving of a fan of a solar dryer is a profitable option and enables easy control of the drying air temperature.
1997-10-01
Development of a retrofit coal combustor for industrial applications
Energy Technology Data Exchange (ETDEWEB)
In this first quarterly technical report for DOE Contract No. DE-AC22-87PC79654, a description of the background, technology, and application is provided. The design and fabrication of advanced combustion chambers were completed during this period. Initial testing on both the bare metal and refractory lined advanced chambers were initiated. The units were tested initially with gas but primarily with coal. A Pittsburgh No. 8 pulverized coal was used for these test activities. Both advanced chambers pulsed well.
1987-01-01
Design, development and testing of A31M wood composite stall regulated blade for serial production
Energy Technology Data Exchange (ETDEWEB)
Despite the long track record of the technology, wood composite has rarely been applied to blades of this scale or for tip braked stall-regulated rotors. This paper describes how the design has been taken successfully from the concept to design through structural testing, certification and operational testing of the prototype set. (orig.)
1999-07-01
DIPAC 2005 7. European workshop on beam diagnostics and instrumentation for particle accelerators
Energy Technology Data Exchange (ETDEWEB)
Accelerators can not be improved without the development of adequate beam instruments and diagnostic tools. This year this statement is particularly right: a lot of contributions are dedicated to beam monitoring and to the design of new beam monitors based on original technologies. This document gathers about 100 contributions.
2005-07-01
Research programs in coal liquefaction are briefly discussed. The following projects are addressed: coal desulfurization by bioprocessing; materials characterization study of liquefaction processes; novel approaches to catalysis in coprocessing and in direct coal liquefaction; liquefaction research in pyrolysis catalysis, and coal dissolution; enhanced reactivity and selectivity in coal liquefaction and coprocessing systems. (CBS)
1989-01-01
Cooperative research in coal liquefaction infratechnology and generic technology development
Energy Technology Data Exchange (ETDEWEB)
Various research programs on coal liquefaction are described. Research efforts are reported from the University of Kentucky, University of Pittsburgh, West Virginia University, University of Utah, and the Center for Applied Energy Research. Research areas include depolymerization, desulfurization, coprocessing catalysis, hydrogenation, and solvent extraction. (CBS)
1989-01-01
Energy Technology Data Exchange (ETDEWEB)
This quarterly report covers the period from January 1, 2005 through March 31, 2005. It covers: technical development, permitting status, engineering status, construction status, operations summary and marketing support activities for this period. Plant startup is still continuing. Testing of admixtures to enhance extrusion and SDA wetting is continuing. Efforts are underway to improve plant availability.
2005-05-01
The non-invasiveness of autofluorescence technology may reduce sampling error and time delay for histopathology diagnosis. We establish biophotonic methods and guidelines to visualize and interpret early epithelial tissue changes that signify disease. Flexible and rigid fiber endomicroscopy instrumentation design parameters feasible for translation towards clinical use are in development.
2010-12-01
EPA's Brownfields Economic Redevelopment Initiative was established to assist states, site planners and other community stakeholders to work together to assess, cleanup and sustainably reuse brownfields sites. EPA has developed a series of guides to help these parties effectively...
Energy Technology Data Exchange (ETDEWEB)
The development of emmissions, the measures planned and carried out and the present state of research in the Federal Republic of Germany into air pollution effects and abatement technology is reported. Possible starting points and solutions for air pollution abatement measures are explored within the legal framework.
1981-01-01
Advancements in electric and hybrid electric vehicle technology
Energy Technology Data Exchange (ETDEWEB)
Contents of this volume include: Influence of Battery Characteristics on Traction Drive Performance; Chassis Design for a Small Electric City Car; Thermal Comfort of Electric Vehicles; Power Quality Problems at Electric Vehicle`s Charging Station; The Development and Performance of the AMPhibian Hybrid Electric Vehicle; The Selection of Lead-Acid Batteries for Use in Hybrid Electric Vehicles; and more.
1994-12-31
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
