KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The dynamic response characteristics of the VAWT rotor are important factors governing the safety and fatigue life of VAWT systems. The principal problems are the determination of critical rotor speeds (resonances) and the assessment of forced vibration response amplitudes. The solution to these problems is complicated by centrifugal and coriolis effects which can have substantial influence on rotor resonant frequencies and mode shapes. This paper will describe and discuss the primary tools now in use at Sandia National Laboratories for rotor analysis. These tools include a lumped springmass model (VAWTDYN) and also finite-element based approaches. The discussion will center on the accuracy and completeness of current capabilities and plans for future research.

Energy Technology Data Exchange (ETDEWEB)

Accurately predicting wind turbine blade loads and response is important for the proper design of wind turbines. The need to accurately predict both deterministic and stochastic blade loads is now widely recognized. Previous rotor code development and validation efforts at NREL have concentrated on prediction of deterministic and stochastic blade loads for rigid hub rotors. During the past year this effort was expanded for predicting blade and shaft loads for two-bladed teetering hub rotors. The NREL (formerly SERI) Teetering Rotor Analysis Program (STRAP), a derivative of the Force and Loads Analysis Program (FLAP), can include the effects of rotor undersling, delta-3 and the effects of a concentrated hub mass. The degrees of freedom include rotor teeter and symmetric and asymmetric rotor flap modes. A time-dependent, prescribed yaw motion ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to numerically explore the non-linear two-dimensional unsteady potential flow over a Savonius rotor and to develop a code for predicting its aerodynamics performances. In the model developed, the rotor is represented in a median plane by two semicircles, displaced along their common diameter. The two semicircles can be considered to produce lifting effects. As a result, they are modelled by a collection of discrete vortices on their contours. The flow field is then governed by the Laplace equation. The versatile Neumann boundary condition, applied over the contour of the semicircles and the Kutta Joukowsky condition applied at the four extremities of the semicircles have been used in the modelling. The torque distribution of the stationary rotor and the unsteady pressure field on the blades of the rotating rotor, predicted by the code developed, have been compared and validated ...

Energy Technology Data Exchange (ETDEWEB)

The dynamic response characteristics of the VAWT rotor are important factors governing the safety and fatique life of VAWT systems. The principal problems are the determination of critical rotor speeds (resonances) and the assessment of forced vibration response amplitudes. The solution to these problems is complicated by centrifugal and Coriolis effects which can have substantial influence on rotor resonant frequencies and mode shapes. This paper will describe and discuss the primary tools now in use at Sandia National Laboratories for rotor analysis. These tools include a lumped spring-mass model (VAWTDYN) and also finite-element based approaches. The discussion will center on the accuracy and completeness of current capabilities and plans for future research. As this paper is meant primarily to provide an overview, much of the detail is omitted and will be presented in a follow-on report.

British Library Electronic Table of Contents (United Kingdom)

Abstract Characteristics of batch rotor-stator mixer performance are elucidated by shaft torque and angle resolved 2D PIV measurements obtained in a full-scale, custom build, bottom-mounted, rotor-stator mixer unit operating in the turbulent regime with water as working fluid. Measurements have been acquired at various rotor speeds corresponding to impeller based Reynolds numbers between 2.0--105 and 8.5--105. The use of a transparent Plexiglas stator facilitated PIV measurements inside and outside the stator as well as into the stator slots themselves. The governing mechanisms controlling the complex flow structures, flow rates, power dissipation, velocity fields, strain rate fields and turbulence intensity fields are explained, highlighting the influence on rotor-stator mixer performance...

Energy Technology Data Exchange (ETDEWEB)

This study presents a dynamic analysis of a rotor supported by two turbulent flow model journal bearings and lubricated with couple stress fluid under nonlinear suspension. The dynamics of the rotor center and bearing center is studied. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The results show that the values of dimensionless parameters l* strongly influence dynamic motions of bearing and rotor centre. It is found that couple stress fluid improve the stability of the system when l* > 0.4 even if the flow of this system is turbulent. We also demonstrated that the dimensionless rotational speed ratios s and ...

Energy Technology Data Exchange (ETDEWEB)

This study presents a dynamic analysis of a flexible rotor supported by two porous squeeze couple stress fluid film journal bearings with non-linear suspension. The dynamics of the rotor center and bearing center are studied. The analysis of the rotor-bearing system is investigated under the assumptions of non-Newtonian fluid and a short bearing approximation. The spatial displacements in the horizontal and vertical directions are considered for various non-dimensional speed ratios. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The numerical results show that the stability of the system varies with the non-dimensional ...

Energy Technology Data Exchange (ETDEWEB)

This paper described a newly developed chipper device for mounting on Claas Jaguar chipper harvesters for short rotation forestry harvesting. It was designed by the Agriculture Engineering Research Unit of the Agricultural Research Council in Rome, Italy. The new rotor has a lower number of blades compared to standard rotors and has a different cutting angle and drum insertion. This study evaluated the particle-size distribution of wood chips produced by standard rotors compared to those with the experimental rotor. The objective was to distinguish the particle size distribution of chips produced using the two types of chippers in order to evaluate the influence of wooden species in the chip formation process. Tests were conducted using 860 and 890 Claas Jaguar chipper harvesters, both equipped with standard and CRA-ING rotors. The experiment was conducted on poplar cultivations on ...

International Nuclear Information System (INIS)

A statistical evaluation of rotor blade damage in axial steam turbines affords an insight into the extent of the repair costs incurred and reveals the types of defects and shortcomings which cause such damage. The great amount of rotor blade damage discovered during control inspections will surprise even many turbine experts. The statistical evaluation is followed by a review of the more frequent causes of damage and their characteristic features, illustrated on the basis of practical examples. This contribution is intended as an aid to both the manufacturers and operators of steam turbines in preventing the oft almost classic types of faults which constantly recur. (orig.).

Science.gov (United States)

The dynamic response characteristics of the VAWT rotor are important factors governing the safety and fatique life of VAWT systems. The principal problems are ...

Science.gov (United States)

Engine model: An engine and governor model adapted from a heavy lift helicopter simulation provides a restistic time delay between aerodynamic rotor ...

International Nuclear Information System (INIS)

The essential difference as well as the apparent identity between the triaxial-rotor model and the gamma-vibrational model have been discussed. From the gamma decay mode, the [19/2"-]_1 states of the j = 11/2"- family in "1"8"7Ir and "1"8"9Ir have been identified as the K = j + 4 states, the presence of which contradicts the particle plus triaxial-rotor model. (author).

Environmental Research Database

Objectives~%~~%~The practical exploitation of tidal stream energy is limited by man's activities in coastal waters: navigation, fishing and~%~leisure pursuits. It is important therefore to make the best use of the sites, which are available. The main objective of the~%~Proposed study is to assess the limits imposed by waves on the performance of tidal stream rotors, and to investigate way:~%~in which these limits might be related by refinements in rotor design and the control of openiting conditions. S~%~ [continued...]DescriptionHorizontal aids wind turbines have been recognised as one of the most successful renewable energy saving devices. The use of the similar concept as a 'tidy~%~~%~stream rotor' in offshore environment appears to be even more compelling. However, the application of this concept will require the confirmation of various operational and environmental limitations due to ...

British Library Electronic Table of Contents (United Kingdom)

This paper presents a combined experimental and computational study into the aerodynamics and performance of a small scale vertical axis wind turbine (VAWT). Wind tunnel tests were carried out to ascertain overall performance of the turbine and two- and three-dimensional unsteady computational fluid dynamics (CFD) models were generated to help understand the aerodynamics of this performance. Wind tunnel performance results are presented for cases of different wind velocity, tip-speed ratio and solidity as well as rotor blade surface finish. It is shown experimentally that the surface roughness on the turbine rotor blades has a significant effect on performance. Below a critical wind speed (Reynolds number of 30,000) the performance of the turbine is degraded by a smooth rotor surface finis...

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy decided to terminate the Flywheel Rotor and Containment Technology Development project during FY 1983. Activities this year included fabrication, inspection, and test evaluation of rotor and containment structures. A peak energy of 700 Wh was stored at an energy density of 70 Wh/kg. In cyclic tests, 10,000 cycles from design speed to half speed were logged without failure. The first test of a lightweight containment structure indicates the need for additional development. In complementary studies, production cost estimates were made for three flywheel designs. In a cooperative program with the University of Wisconsin, work began on construction of a flywheel/continuously variable transmission/heat engine car which promises fuel economy improvements of up to 100%. Suggestions are made for the direction of future work when interest in flywheel system reappears.

Energy Technology Data Exchange (ETDEWEB)

A thermal-electric mathematical model for a squirrel cage induction motors which permits to specify the best motor for specific drive, under thermal and electric aspects based, only on manufacturer technical bulletins and technical information is presented. Changes of rotor parameters due Skin Effect and changes of winding resistances (both stator and rotor) with the temperature are considered. The accuracy of this model is appraised using experimental results. The thermal behavior and electric performance for some motors are obtained for continuos and intermittent duties with sinusoidal and non-sinusoidal voltages. (author)

International Nuclear Information System (INIS)

There are 173 three quasiparticle rotational bands, out of which 38 bands display signature splitting and sometimes a signature inversion also. The observed signature splitting is basically due to the higher order Coriolis coupling and calculation based on particle rotor model (PRM) are in progress

UK PubMed Central (United Kingdom)

1. Interactions of pyrazole and ethanol were studied in three laboratory test procedures. They included sleeping time in mice, rotor rod balance in rats and lever pressing behaviour of rats. 2....Full Text Available

International Nuclear Information System (INIS)

Technologic regimes of cryomotor rotor fabrication are determined. Blanks of yttrium ceramics powder are molded hydrostatically at 400-600 MPa. To confirm the serviceability of electric machines of the considered, a hysteretic 10 W power electric motor with the following dimensions of HTSC-ceramics rotor: external diameter - 56 mm; internal diameter - 45 mm, height - 60 mm, is developed and tested in the liquid nitrogen medium. 8 refs.; 8 figs.; 1 tab.

Energy Technology Data Exchange (ETDEWEB)

An apparatus is provided for rapidly restarting the flow of coolant through the cold electromagnetic shield of a superconducting rotor following a thermal transient episode. A vortex diode inhibits coolant flow in the undesirable reverse direction and encourages the reestablishment of a normal thermosyphon cooling loop flow quickly following the termination of a thermal transient such as that caused by transmission line faults. The present invention requires no moving parts and may therefore be permanently sealed in the superconducting rotor without risk of costly repair efforts caused by components failure.

International Nuclear Information System (INIS)

The high-spin states in transitional odd-mass nuclei are studied in terms of an odd quasi-particle coupled to an asymmetric rotor with a variable moment of inertia (VMI). In order to take into account the VMI, the basis states are expanded in terms of the core eigenfunctions. Excitation energies, quadrupole moments, magnetic moments, B(E2) values and B(M1) values are calculated and compared with the experimental data for nuclei in Au and La regions. On comparison with other descriptions it is found that the treatment with VMI provides a more satisfactory explanation of the data. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Emulsions now find a wide range of applications in industry and daily life. In the pharmaceutical industry lipophilic active ingredients as well as many nutritional products such as vitamins are often formulated in the dispersed phase of oil-in-water emulsions. Emulsions can be produced with different mechanical emulsification techniques. In the following review, the process of rotor-stator systems and disc systems are compared to other popular mechanical emulsification systems. On the basis of experimental results from the authors' laboratory, a discontinuous gear-rim dispersing system, discontinuous disc system, and a continuous high pressure system are compared with regard to their attainable mean droplet diameter and drop size distribution in an oil-in-water emulsion. It can be shown that dissolver discs with a very simple geometry attain very small mean droplet diameters and a very narrow droplet size distribution, comparable to the emulsions obtained ...

Energy Technology Data Exchange (ETDEWEB)

Double streamtube codes model the curved blade (Darrieus-type) vertical-axis wind turbine (VAWT) as a double actuator-disk arrangement (one disk for the upwind half of the rotor and a second disk for the downwind half) and use conservation of momentum principles to determine the forces acting on the turbine blades and the turbine performance. These models differentiate between the upwind and downwind sections of the rotor and are capable of determining blade loading more accurately than the widely-used single-actuator-disk streamtube models. Additional accuracy may be obtained by representing the turbine as a collection of several streamtubes, each of which is modeled as a double actuator disk. This is referred to as the double-multiple-streamtube model. Sandia National Laboratories has developed a double-multiple streamtube model for the VAWT which incorporates the effects of the incident wind boundary layer, nonuniform velocity between the ...

Energy Technology Data Exchange (ETDEWEB)

A stochastic wind simulation for VAWTs (VSTOC) has been developed which yields turbulent wind-velocity fluctuations for rotationally sampled points. This allows three-component wind-velocity fluctuations to be simulated at specified nodal points on the wind-turbine rotor. A first-order convection scheme is used which accounts for the decrease in streamwise velocity as the flow passes through the wind-turbine rotor. The VSTOC simulation is independent of the particular analytical technique used to predict the aerodynamic and performance characteristics of the turbine. The VSTOC subroutine may be used simply as a subroutine in a particular VAWT prediction code or it may be used as a subroutine in an independent processor. The independent processor is used to interact with a version of the VAWT prediction code which is segmented into deterministic and stochastic modules. Using VSTOC in this fashion is very efficient with regard to decreasing ...

British Library Electronic Table of Contents (United Kingdom)

Abstract In this paper, a new predictive model that can forecast the performance of a vertical axis wind turbine (VAWT) is presented. The new model includes four primary variables (rotor velocity, wind velocity, air density, and turbine power output) as well as five geometrical variables (rotor radius, turbine height, turbine width, stator spacing, and stator angle). These variables are reduced to include the power coefficient (Cp) and tip speed ratio (TSR). A power coefficient correlation for a novel VAWT (called a Zephyr Vertical axis Wind Turbine (ZVWT)) is developed. The turbine is an adaptation of the Savonius design. The new correlation can predict the turbine's performance for altered stator geometry and varying operating conditions. Numerical simulations with a rotating reference f...

Science.gov (United States)

Sandia Laboratories, as part of its investigation of the Darrieus Vertical Axis Wind Turbine (VAWT), has been involved recently in an economic assessment of the concept. The class of VAWT's investigated use curved, fixed-pitch blades of constant section rigidly attached to a vertical rotating tower. Qualitatively, the main advantages of the VAWT over more conventional, propeller-type machines are the elimination of yaw controls, the placement of mechanical equipment at ground level, its amenability to simple, low-cost blade fabrication techniques, and aerodynamic stall characteristics which eliminate the need for active pitch control devices. The main disadvantages relative to modern propeller machines are a somewhat lower aerodynamic efficiency (about 10% lower), the limited ability of the rotor to self-start, and generally lower rotor operating RPM's, which leads to higher torque capacity requirements for the drive train.

Science.gov (United States)

Sandia National Laboratories has developed a family of airfoils specifically designed for use in the equatorial portion of a Vertical-Axis Wind Turbine (VAWT) blade. An airfoil of that family has been incorporated into the rotor blades of the DOE/Sandia 34-m diameter VAWT Test Bed. The airfoil and rotor design process is reviewed. Comparisons with data recently acquired from flow visualization tests and from the DOE/Sandia 34-m diameter VAWT Test Bed illustrate the success that was achieved in the design. The economic optimization model used in the design is described and used to evaluate the effect of modifications to the current Test Bed blade. 1 tab., 11 figs., 13 refs.

Energy Technology Data Exchange (ETDEWEB)

Flywheels containing fiber-reinforced composite materials have attributes suitable for vehicular propulsion, indicating the need for rotor designs which are easily manufactured and low in cost. This development goal was pursued in a cooperative effort between Owens-Corning Fiberglas and Lawrence Livermore Laboratory which investigated flywheels made from compression-molded sheet molding compound (SMC). The design resulted from a Lawrence Livermore analysis, with successful fabrication achieved using a procedure developed by Owens-Corning. Details concerning materials selection, rotor fabrication, and testing are discussed. Owens-Corning subsequently initiated a technical/marketing survey to determine current industrial interests in a low-cost flywheel design; precursory information, pertaining to composite flywheels in particular, is described.

International Nuclear Information System (INIS)

The advantages and disadvantages of single-point or double-point bearing of rotors with several single shafts are illustrated by examples from the KWU series. The design features of modern bearings are described. Some results from the test program for the development of these bearings are reported. In the last section the vibration behavior of the shafts is considered. Various phenomena - like self-excited vibrations and those caused by unbalance or the influence of partial admission - are briefly discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

This paper will describe the application of power generation by the use of microturbine technology by Capstone Turbine Corporation throughout South America. The purpose of this paper is to describe the technology and the experience gained over the last six years. The microturbines are power generation systems that produce energy from a diverse range of liquid or gaseous fuels. The generator is driven by a small gas turbine with a common shaft for the rotors of the generator and the engine. (author)

Energy Technology Data Exchange (ETDEWEB)

Transonic flows with heat addition due to condensation are important to many technical applications, e.g. to the last stages of large steam turbines, where nucleation and droplet formation become important. Our current research concentrates on the interaction of vortex shedding with condensation in turbines and on rotor/stator interaction in nucleating flows. Both phenomena lead to a significant change of the condensate mass and the droplet radius distribution in the downstream two-phase flow regime. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Despite the long track record of the technology, wood composite has rarely been applied to blades of this scale or for tip braked stall-regulated rotors. This paper describes how the design has been taken successfully from the concept to design through structural testing, certification and operational testing of the prototype set. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A self-tuning Power System Stabilizer (PSS) is suggested in this paper. Computer simulations, of a lightly-damped single turbine-generator supplying power to an infinite bus system, show that this self-tuning PSS can work over a large operating range and make a significant improvement in rotor damping.

Energy Technology Data Exchange (ETDEWEB)

Power system stabilizers (PSSs) are used to enhance damping of power system oscillations through excitation control of synchronous generator. The objective of the PSS is to generate a stabilizing signal, which produces a damping torque component on the generator shaft. Conventional PSSs are designed with the phase compensation technique in the frequency domain and include the lead-lag blocks whose parameters are determined according to a linearized power system model. The performance of conventional PSSs (CPSSs) depends upon the generator operating point and the system parameters, but a reasonable level of robustness can be achieved depending on the tuning method. This paper presents a new three-dimensional PSS (3D PSS), which uses rotor speed deviation, rotor acceleration and load angle deviation as input signals. The 3D PSS attempts to return the generator to the state-space origin, based on the generator's trajectory in state-space ...

Science.gov (United States)

The Wind Energy Research Division of Sandia National Laboratories has been funded by the Wind/Ocean Technology Division of the Department of Energy (DOE) to design and build a 34-meter diameter Vertical Axis Wind Turbine (VAWT). The turbine design incorporates the results of recent VAWT research in aerodynamics and structural dynamics. Initial system concept studies identified several blade options that met the required power rating of 500 kW. The final blade and rotor configurations were chosen based on finite element calculations that determined the turbine modes of response, their frequency of vibration, and stress levels. For parked survival turbine components were designed to with stand the loading of a 150 mph (67.0 m/s) wind coupled with maximum cable tensions. Specific areas of design discussed include the rotor, cables, bearings, brakes, and foundations. Construction of the turbine is in progress at this time and anticipated completion ...

Energy Technology Data Exchange (ETDEWEB)

The rebuilt rotor of the 224 kW Magdalen Islands VAWT was installed in 1979 and has been operating at its design speed (36.6 rpm) for about one year. Agreement between measured and theoretical performance is generally good except that maximum power may exceed theoretical predictions. Measurements of drive train losses, torque and power ripple, and rotor stresses are discussed. Although peak-to-peak cyclic stress levels are low in relation to fatigue life limits, spectral analysis of stress data indicates that the 3-per-rev component is amplified by near-resonance with the first butterfly blade mode. This resonance was subsequently de-coupled by a damped connection between the blade struts and the central column. The major future project in the Canadian program is the design, construction and testing of a megwatt-scale VAWT in cooperation with Hydro Quebec. Preliminary desigh details of this turbine, known as Project Aeolus are briefly ...

International Nuclear Information System (INIS)

Based on a detailed analysis of the inter-relationship in the current, voltage, electromagnetic torque and ratio of the difference between the speed of rotor and the speed of rotary magnetic field to the later in the motor, the root cause was point out, which leads to the protection fuses' failure of the motor in the starting stage, which drives the turbine-generator set to rotate at low speed before its startup. Two solutions to avoid the situation are proposed, too. (authors)

Energy Technology Data Exchange (ETDEWEB)

In a treatment system of radioactive waste solution including sodium sulfate generated from a boiling water type nuclear reactor, waste solution is fed into a thin film evaporator where the waste solution is evaporated and made into powder while precipitating in a peripheral surface of the evaporator vessel. The surface of the precipitated solid is wiped by rotating wiper blades and removed off as radioactive solid powder. The rotational speed of a rotor to which the wiper blades are secured is controlled at a minimum and necessary rotational speed which contributes to make the waste solution into the powder so that the rate of worn out of the wiper blade is decreased.

Energy Technology Data Exchange (ETDEWEB)

The invention concerns the conversion of steam turbines, particularly condensation turbines, for the economic coupling of process steam and heating steam. The conversion occurs by retaining the basic construction of foundations, housing and bearings as support group and coupling member and matching the specially developed construction for the idea of use into the existing housing, and inserting the rotor into the shaft unit. By having the unchanged supports of the housing and the bearings of the shaft unit, the elasticity in expansion and the vibration behaviour of the turbine are retained and the conversion costs can be lowered.

Energy Technology Data Exchange (ETDEWEB)

A feasibility study test and 3 field trials were performed at Darlington NGS in 1996, 1999 and 2000 on ABB LP turbines. The scope of these trials was to commission in-situ automatic phased array systems capable to inspect blade roots and rotor steeples of L-0 and L-1 rows. GE disk-blade rim attachments were inspected at Bruce B nuclear station, in fall of 1999. The automated ultrasonic phased array technology is capable of high-speed rate and reliable detection and sizing. The capability demonstration was performed on mock-ups and reference blocks, using EDM notches. A custom built UT simulation software: Imagine 3D interfaces with SimScan to generates the spreadsheets/charts with target and probe coordinates and ultrasonic path and angles (refracted and skew) to hit the reference target. Examination of L-0 blade and rotor steeple grooves was performed with 2 phased array systems under networking. Data analysis was done in near-real time. ...

Energy Technology Data Exchange (ETDEWEB)

An expert system was developed which helps maintenance personnel diagnose the condition of rotor and stator windings and their cores, in motors and generators rated 2300 V and above. The expert system, called MICAA[TM], used an approach which has been found to be effective for diagnosing medical problems. The program required the user to input machine nameplate information, operating status, and any past test data available. In addition, the program would suggest tests that may be useful, as well as provide guidance to maintenance personnel on what to look for in visual inspections of the machine. The expert system stored and correlated all this information, calculated the overall condition of the component in question, and identified the most likely specific causes of any deterioration. The basic methodology of motor and generator condition assessment, and the architecture and processing performed by MICAA to obtain these capabilities were discussed and described. ...

British Library Electronic Table of Contents (United Kingdom)

The Na+-driven bacterial flagellar motor is a molecular machine powered by an electrochemical potential gradient of sodium ions across the cytoplasmic membrane. The marine bacterium Vibrio alginolyticus has a single polar flagellum that enables it to swim in liquid. The flagellar motor contains a basal body and a stator complexes, which are composed of several proteins. PomA, PomB, MotX, and MotY are thought to be essential components of the stator that are required to generate the torque of the rotation. Several mutations have been investigated to understand the characteristics and function of the ion channel in the stator and the mechanism of its assembly around the rotor to complete the motor. In this review, we summarize recent results of the Na+-driven motor in the polar flagellum of ...

Energy Technology Data Exchange (ETDEWEB)

A more complete level scheme is presented here for the decay of [sup 187]Pt, incorporating many new lines and levels up to 2.4 MeV. Emphasis has been placed on the extraction of multipole mixing ratios from nuclear orientation data. Analysis of that data, however, required a more complete understanding of the level structure (including, in particular, branching ratios, conversion coefficients, and level feedings), prompting the collection of new spectroscopy data. The low-lying, positive-parity levels are described in terms of (odd-proton) single-particle Nilsson states coupled to a triaxial core. Multipole mixing ratios are compared to those calculated in the Particle-Plus-Triaxial-Rotor Model. (orig.).

Science.gov (United States)

Double streamtube codes model the curved blade (Darrieus-type) vertical axis wind turbine (VAWT) as a double actuator fish arrangement (one half) and use conservation of momentum principles to determine the forces acting on the turbine blades and the turbine performance. Sandia National Laboratories developed a double multiple streamtube model for the VAWT which incorporates the effects of the incident wind boundary layer, nonuniform velocity between the upwind and downwind sections of the rotor, dynamic stall effects and local blade Reynolds number variations. The theory underlying this VAWT model is described, as well as the code capabilities. Code results are compared with experimental data from two VAWT's and with the results from another double multiple streamtube and a vortex filament code. The effects of neglecting dynamic stall and horizontal wind velocity distribution are also illustrated.

British Library Electronic Table of Contents (United Kingdom)

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150degreeC, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Youngs modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Youngs modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the i...

Science.gov (United States)

The effect of high lift airfoils on the cost effectiveness of HAWT and VAWT (horizontal and vertical axis wind turbine) machines is studied. The scope involved first studying modern two dimensional airfoils, and developing a generalized formulation for their performance in terms of lift, drag, and thickness at appropriate Reynolds numbers. Single element, multi-element, symmetrical, extra thick airfoils and jet flap airfoils were analyzed. The jet flap airfoils were considered to be unacceptable because of excessive power requirements. Then the effect of using the above airfoils on the rotors of a variety of wind turbines was made. Qualitative representation of the type of airfoils studied is given.

Energy Technology Data Exchange (ETDEWEB)

This report describes experiments to determine whether a wiped film evaporator (WFE) might be used to concentrate low-level liquid radioactive waste (LLLW). Solutions used in these studies were surrogates that contain no radionuclides. The compositions of the surrogates were based on one of Oak Ridge National Laboratory`s (ORNL`s) Melton Valley Storage Tanks (MVSTs). It was found that a WFE could be used to concentrate LLLW to varying degrees by manipulating various parameters. The parameters studied were rotor speed, process fluid feed temperature and feed rate, and evaporator temperature. Product consistency varied from an unsaturated liquid to a dry powder. Volume reductions up to 68% were achieved. System decontamination factors were consistently in the range of 10{sup 4}.

Energy Technology Data Exchange (ETDEWEB)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This report describes the theoretical background of the VAWT Stochastic Aerodynamic Loads (VAWT-SAL) computer code, whose purpose is to numerically simulate these random loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Stream Tube (DMST) analysis is employed to model the rotor's aerodynamic response. The analysis includes the effects of Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. The mean ambient wind is assumed to have a shear profile which is described by either a power law or a logarithmic variation with height above ...

Science.gov (United States)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This paper discusses the development of a model for the simulation of these stochastic loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Streamtube analysis is employed, which includes the effects of wind shear. Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. Calculations are presented for the VAWT 34-m Test Bed currently being assembled at Bushland, Texas. Time histories of the loads, as well as their Fourier spectra, are presented and discussed. An unexpected finding is that the average output power is predicted to be more sensitive to turbulence level than ...

Energy Technology Data Exchange (ETDEWEB)

A process and apparatus for solidifying radioactive waste liquid containing dissolved and/or suspended solids is disclosed. The process includes chemically treating for pH adjustement and precipitation of solids, concentrating solids with a thin-film evaporator to provide liquid concentrate containing about 50% solids, and drying the concentrate with heated mixing apparatus. The heated mixing apparatus includes a heated wall and working means for shearing dried concentrate from internal surfaces and subdividing dry concentrate into dry, powdery particles. The working means includes a rotor and helical means for positively advancing the concentrate and resulting dry particles from inlet to outlet of the mixing apparatus. The dry particles may also be encapsulated in a matrix material. Entrained particles in the vapor stream from the evaporator and mixer are removed in an integral particle separator and the vapor is subsequently condensed and may be recycled upstream ...

International Nuclear Information System (INIS)

A transient stability program was developed for the Taiwan Power Company, which has a high proportion of nuclear generation in its power system. This program offers a new territory to investigate nuclear plant effects on the power system transient stability. This program also provides a high speed tool for the Taipower system operational planning. A generalized procedure of synchronous machine modeling for a large-scale stability study is presented. The merits and weaknesses of machine modeling can be comprehended through each item of this procedure. Three types of nonlinear synchronous machine modeling implemented into this stability program are derived by following this procedure. A robust subroutine was derived to perform the fourth order Runge-Kutta integration method, making the software programming neat and systematical. For simulating the nuclear plant influence on the system, this program implemented an additional four functions: load-limit operation simulated by a low-value ...

Energy Technology Data Exchange (ETDEWEB)

The development of turbine components for the automotive 100 kW ceramic gas turbine has entered the final stage of the seven-year project and is making satisfactory progress, toward the goals. The authors attained the interim targets of the aerodynamic performances and have been carrying out tests to further improve efficiency. As for ceramic parts, they have changed the material of the turbine rotor to a new one that is excellent in long-sustained and high-temperature strength properties, and have confirmed substantial strength at high temperature through hot-spin tests. After evaluating blade-vibration stress through analyses and experiments, the authors completed an endurance evaluation at 1200 C (1473 K) TIT (Turbine Inlet Gas Temperature) and a rated speed of 100,000 rpm. The authors are now carrying out endurance tests at 1350 C (1623 K) TIT. For ceramic stationary parts, they already finished the evaluations at 1200 C TIT and are also conducting an endurance ...

Energy Technology Data Exchange (ETDEWEB)

A wind turbine is disclosed which permits high energy production over a wide range of wind forces while being protected against climatic hazards. According to the invention, a mast supports an energy recuperator comprising vane-type rotors by means of a frame which is orientable around a vertical axis. An energy conversion device is connected to the recuperator in order to be driven in rotation by the recuperator. The frame is responsive to the aerodynamic force exerted on the recuperator with respect to the mast and to the ground so as to optimize the power collected by the machine. The frame comprises a turret pivoted to the mast about the vertical axis and a structure pivoted to the turret about a horizontal axis of tilting motion. A balance weight maintains the recuperator in the top position when there is no wind. The aerodynamic drag of the recuperator acts in the opposite direction. In consequence, in the event of a high wind, the recuperator moves down ...

Energy Technology Data Exchange (ETDEWEB)

Large capacity adjustable speed machines (ASMs) at pumped storage power station have been put into full operation and the operating characteristics of ASM have been highly evaluated from the view point of power system operation. The output power (input power) of ASM can be controlled very quickly by applying a vector control scheme to the excitation control. This quick responsive feature of ASM can make it possible to improve the stability of the neighbor sub-power system. For improvement of transient stability, the output power of ASM is reduced very quickly in order to control the acceleration of neighbor generators during and after transmission line faults. For improvement of dynamic stability, the output power of ASM is modulated in accordance with the stabilizing signals detected from the swing of generator rotor or the power flow fluctuation on the transmission line. This paper describes the design concepts and method of control system for improving the ...

Energy Technology Data Exchange (ETDEWEB)

A highly reliable control rod drive mechanism (CRDM) installed inside the reactor vessel has developed for use of an advanced marine reactor. This CRDM contributes to compactness and simplicity of the reactor system, and it can eliminate the possibility of a rod ejection accident. The CRDM works in the high temperature and high pressure water - 310degC and 12 MPa, the same atmosphere as the primary loop. Driving force is produced by a synchronous motor with the rotor of a permanent magnet, which has been developed. An innovative latch mechanism using separable ball nuts can latch driving shaft connecting the control rod and de-latch it for scram. The rod position detector using a magnetostrictive wire type sensor on the principle of Wiedeman effect has been developed, accuracy of which is verified to have a detecting error within 1.2 mm. Ball bearings for thrust and radial supports in rotation have been developed to be capable of working under the high temperature ...

Energy Technology Data Exchange (ETDEWEB)

This report surveys the possibilities and restrictions of different construction materials for the purpose of the blades of a small stall regulated turbine. For example scaling up, material saving at decreasing of static or dynamic loads, comparisons of global costs based on prices per unit of weight, etc. For the mutual comparison of construction materials for turbine blades the starting point is a stall regulated horizontal axis turbine with a rotor diameter of 16 m and a tipvane speed of about 64 m/s. Short descriptions are given of the materials and of the applied production methods with the resulting blade geometry. The blade skins are dimensionized for storm loads after the optimalization of the blade geometry, needed for the design wind speed, is recorded. The resulting blade skins are mutually compared as for weight, mass inertia and bending stiffness. Also a comparison took place of the resulting reserve factors against load variations caused by gusts of ...

Energy Technology Data Exchange (ETDEWEB)

Wind power is an increasingly significant renewable energy resource, producing no environmentally damaging C0{sub 2} emissions. The efficient production of electricity by wind turbines relies on aerodynamics: aerodynamics of wind turbines provides the fundamental solutions to efficient wind turbine design. Following a historical introduction, Part 1 of Aerodynamics of Wind Turbines is concerned with basic rotor aerodynamics, while Part 2 deals with structural aspects of the wind turbine and calculation of the loads on it. Topics covered include increasing mass flow through the turbine, performance at low and high wind speeds, assessment of the extreme conditions under which the turbine will perform and the theory for calculating the lifetime of the turbine. The classical Blade Element Momentum method is also covered, as are eigenmodes and the dynamic behaviour of a turbine. Aerodynamics of Wind Turbines is an essential reference for both engineering students and ...

Energy Technology Data Exchange (ETDEWEB)

This paper evaluates abrasive jet wear tests, carried out on the ZUK-3M abrasion apparatus according to the GOSF 23.201-78 industrial standard. As abrasive material, brown coal coke dust, brown coal dust, power plant fly ash and quartz sand (for the purpose of comparison) were employed. Seventeen types of materials were blasted with abrasive jets, including a selection of steels, glass, rubber, SYS-pur plastics, cast basalt, Kawenit and vitroceramics. The test apparatus produced abrasive jet velocities between 12 and 130 ms/SUP/-/SUP/1 at rotor revolutions of 1,000 to 10,000 min/SUP/-/SUP/1. Blasted material samples were arranged at angles between 15 and 90 degrees. Various tables and graphs present abrasivity results. These results were employed for technical modifications of dedusting equipment in briquetting and coking plants, which led to a threefold increase in service life of abrasion endangered equipment parts. (8 refs.) (In German)

Energy Technology Data Exchange (ETDEWEB)

The nuclear structure of A {proportional_to} 100 nuclei has been studied in the frame of this thesis with a recently developed {beta} - {gamma} - {gamma} triple coincidence fast timing technique and different models such as shell model, hydrodynamic model, Nilsson and particle-rotor models. This technique which allows the measurement of the level lifetimes in the ps range has been applied at JOSEF at the research reactor DIDO of KFA Juelich in studes of the short-lived neutron-rich nuclei in the A {approx_equal} 100 region. Lifetimes of level in {sup 96},{sup 98},{sup 100} ZR, {sup 99},{sup 101}-{sup 104} Nb, {sup 100}-{sup 105} Mo have been measured, which are in many cases completely new, and otherwise more precise than previously published data. From the lifetimes of the members of rotational bands, the size of the nuclear deformations has been deduced. (orig./HSI). [Deutsch] Im Rahmen dieser Doktorarbeit wurde die Kernstruktur der A {proportional_to} 100 Kerne ...

Energy Technology Data Exchange (ETDEWEB)

The gas phase high resolution spectroscopic study of weakly bound clusters can provide the information necessary to develop an intermolecular potential energy surface. This surface can then be used to better understand condensed phases. In this work, a tunable far infrared laser spectrometer is used to study weakly bound dimers produced in the newly developed continuous planar supersonic jet expansion apparatus. The water dimer is an extensively studied hydrogen bonded dimer. It undergoes several tunneling motions which result in splittings and perturbations of the rovibrational energy levels. A review is presented of much of the experimental and theoretical work done on water dimer, including a description of the combined fit of all the high resolution spectroscopic results by Coudert and Hougen. Also included is a discussion of the measurement of the K = 1 lower {yields} K = 2 lower band performed using the tunable far infrared laser/planar jet apparatus. The preliminary results from ...

International Nuclear Information System (INIS)

The object of this paper is to identify the key elements that impact a radiation dose at EAB (Exclusion Area Boundary). This study is based on the AST (Alternative Source Terms) as defined in Regulatory Guide 1.183. The LOCA (Loss of Coolant Accident) and the LRA (Locked Rotor Accident) are selected as limiting cases. A sensitivity analysis of accidental behavior with respect to various parameters during LOCA and LRA at Kori Unit 1 is also undertaken for the following objectives: to determine the limiting parameters, to find the impact trend of the radiation dose, and to find the safety margin between AST and TID (Technical Information Document) methodologies. This work confirms that key parameters are particulate removal rate, decontamination factor, iodine chemical form, gap fraction, partitioning factor, and the impact of isotopes group. Comparing TID with AST, the radiation dose of TID is about 80% greater than that of AST under a LOCA, and about 60% greater ...

International Nuclear Information System (INIS)

Laser spectroscopy measurements have been performed on neutron-deficient and stable Ir isotopes using the COMPLIS experimental setup installed at ISOLDE-CERN. The radioactive Ir atoms were obtained from successive decays of a mass-separated Hg beam deposited onto a carbon substrate after deceleration to 1kV and subsequently laser desorbed. A three-color, two-step resonant scheme was used to selectively ionize the desorbed Ir atoms. The hyperfine structure (HFS) and isotope shift (IS) of the first transition of the ionization path 5d"76s"2"4F_9_/_2#->#5d"76s6p"6F_1_1_/_2 at 351.5nm were measured for "1"8"2"-"1"8"9Ir, "1"8"6Ir"m and the stable "1"9"1","1"9"3Ir. The nuclear magnetic moments #mu#_I and the spectroscopic quadrupole moments Q_s were obtained from the HFS spectra and the change of the mean square charge radii from the IS measurements. The sign of #mu#_I was experimentally determined for the first time for the masses 182#=#+0.2 for the lighter group A=186g, 185, 184, 183 ...

Energy Technology Data Exchange (ETDEWEB)

High temperature components of power plants are in many cases subjected to variable loading conditions such as cyclic creep or strain cycling. Therefore the cyclic behaviour of important heat resistant steels has been investigated under stress control and to a smaller extent under strain control. The behaviour under cyclic creep rupture conditions was determined in long term experiments covering a wide range of loading conditions. This behaviour can be described with the modified life fraction rule and a factor concept of relative life for single stage cycles and additionally with a multistep hypothesis for multi-stage cycles. The description can be adapted to estimate the life consumption under service type random conditions. The strain cycling behaviour was investigated in regard to the conditions of the heated surface of large components. To simulate this type of loading and to generate long term creep fatigue data, a service type strain cycle was developed. Anisothermal and ...