;Contents: Comparison of Simulation Modules of TRANSYT and INTEGRATION Models; Evaluation of SCATSIM-RTA Adaptive Traffic Network Simulation Model; Comparison NETSIM, NETFLO I, and NETFLO II Traffic Simulation Models for Fixed-Time Signal Control; Traffic Flow Simulation Through Parallel Processing; Cluster Analysis as Tool in Traffic Engineering; Traffic Platoon Dispersion Modeling on Arterial Streets; Hybrid Model for Estimating Permitted Left-Turn Saturations Flow Rate; and Passing Sight Distance and Overtaking Dilemma on Two-Lane Roads.
Traffic jams have become very serious at multiforked road intersections, and conventional pre-timed controls are less effective in such situations. In this article, a new traffic signal control system for multi-forked roads is proposed. First, the cellular automaton (CA) model is used to develop a traffic simulator for multi-forked roads. Next, a stochastic model of a traffic jam is built up. In addition, a new traffic signal control algorithm is designed using the optimization technique and a genetic algorithm (GA). Finally, the effectiveness of the proposed method is shown using actual traffic data with a traffic simulator.
Seasonal traffic on intercity corridors often creates severe congestion at various bottlenecks, such as land-drops and drawbridges. A Traffic Simulation And Optimization model (TSAO) has been developed in order to 1) evaluate traffic impacts (including travel time, vehicle operating costs, accidents, air pollution and fuel consumption) of a given routing pattern on a network, and 2) determine the optimal flow pattern. In its latest version, the TSAO model uses: 1) a macroscopic simulation approach to trace vehicle platoons through a network; 2) Greenshield's equation to represent volume-speed relationship on freeways and multi-lane highways, and Highway Capacity Manual method for two-lane rural highways; 3) Lighthill's shockwave function to simulate queue propagation; 4) event-scan time management for simulation; 5) variable link capacity for ...
The traffic flow information guidance can improve the operating efficiency of regional traffic. On the basis of the information guidance model and survey data, this paper takes advantage of the VISSIM software to simulate the traffic in a region within the Southwest Second Ring of Beijing constructed by six roads and six intersections and makes a comparative evaluation on the operation of the regional road traffic flow before and after the implementation of the traffic flow information guidance measures. The analysis of five different guided flow cases shows that if the guided left-turn traffic flows in southbound I.A increases from 10% to 30%, the travel time of the left-turn traffic flow in southbound I.A has a reduction from 18% to 42%, and its delay also reduces from 234 s to 164 s. In...
We introduced a probability of traffic light, PL, at an intersection when approaching cars in two roads are in same conditions. As a application, we proposed a modified Nagel-Schreckenberg cellular automata model for describing a conflicting vehicular traffic flow at the intersection. The results show that the plateau region in the fundamental diagrams, caused by the effect of interaction, is dependent not only on the probability PL, but also on the adaptive schemes.
Network generators that capture the Internet's large-scale topology are crucial for the development of efficient routing protocols and modeling Internet traffic. Our ability to design realistic generators...Full Text Available
processes, we construct a stochastic dynamic model for air- craft counts in ... Also , queueing models for the arrival of aircraft at ... A queueing model has also been used to study ...... Assignment and Aircraft-Sequencing Algorithms in Terminal ...
This publication describes the modification of the road traffic exhaust emission calculation model LIISA and presents the new calculation results. The model has already established its position as the most important inventory tool for regional road traffic emissions in Finland. The LIISA model calculates road traffic emissions as a whole. The system comprises of three separate models: 1. a model for calculating automobile emissions for the years 2001-2021, 2. a model for calculating emissions backwards for the years 1980-2000, 3. a model for calculating the emissions of motorcycles and mopeds. All three parts have been modified. The LIISA model is one of the submodels of the comprehensive LIPASTO calculation system developed at VTT Building and Transport. The ...
In general, macroscopic material failure is a manifestation of irreversible changes at the microscopic level. Many tissues, which may appear to be macroscopically homogeneous, are, at a fundamental microscopic level, a composite material. For example, cornea is composed of a hyaluronic acid matrix in which layers of collagen fibers are overlaid in a crossing pattern. The points where the collagen fibers intersect are potential nucleation sites for microscopic defects, which under the action of tensile stress, nucleate, grow and coalesce to form macroscopic failure planes, or spall planes. Using a model based on microstructural evolution, this paper examines the failure process during photoablation. Specifically, the paper describes a physically motivated, micromechanical model based on the nucleation and growth of spherical voids. This model is then used to ...
This manuscript is a contribution on the modeling of H.263 traffic in multipoint videoconference sessions over IP Networks. Our study includes analysis and modeling assessment of extensive data gathered during realistic videoconference sessions between commercial H.263-compliant terminal clients (with different videoconference software packages installed). All terminal clients were communicating through a Multipoint Control Unit (software or hardware MCU) at `switched presence' mode and for comparative purposes the same typical videoconference content (a person speaking, with mild movement and occasional zoom/span) was used. The analysis of the H.263 data at the frame level suggests that the traffic from the different terminals to the MCU can be represented by a stationary stochastic proce...
Recently, the forecasting technologies for network traffic have played a significant role in network management, congestion control and network security. Forecasting algorithms have also been investigated for decades along with the development of Time Series Analysis (TSA). Chaotic Time Series Analysis (CTSA) may be used to model and forecast the time series by Chaos Theory. As one of the prevailing intelligent forecasting algorithms, it is worthwhile to integrate CTSA and Support Vector Machine (SVM). In this paper, after the vulnerabilities of Local Support Vector Machine (LSVM) in forecasting modeling are analyzed, the Dynamic Time Wrapping (DTW) and the ?Dynamic K? strategy are introduced, as well as a short-term network traffic forecasting algorithm LSVM-DTW-K based on Chaos Theory an...
The aim was to compare the energy consumption by private and commercial vehicles with that of public transport facilities constituting urban street traffic, and to evaluate the influence of various traffic related plans such as green waves (where cars are able to drive through the town with relatively few accelerations and braking) streets with lower speed limits and special lanes and priorities for buses. The traffic pattern in four Copenhagen streets (Jagtvej, Soelvgade, Bredgade and Strandvejen) were measured and analyzed both in, and not in, the rush hour, and a special model was used to calculate the energy consumption. The model defines degree of acceleration and slow-down and speed when calculating energy consumption with regard to various driving patterns. It also calculates carbon dioxide emission. It was found that energy consumption decreased with increasing driving speed ...
The aim was to compare the energy consumption by private and commercial vehicles with that of public transport facilities constituting urban street traffic, and to evaluate the influence of various traffic related plans such as green waves (where cars are able to drive through the town with relatively few accelerations and braking) streets with lower speed limits and special lanes and priorities for buses. The traffic pattern in four Copenhagen streets (Jagtvej, Soelvgade, Bredgade and Strandvejen) were measured and analyzed both in, and not in, the rush hour, and a special model was used to calculate the energy consumption. The model defines degree of acceleration and slow-down and speed when calculating energy consumption with regard to various driving patterns. It also calculates carbon dioxide emission. It was found that energy consumption decreased with increasing driving speed ...
In light of the global focus on greenhouse gas emissions, energy consumption of communication networks has become an important research area. Networks are major energy consumers and are generally dimensioned for peak loads. For extended periods, resources consume power, but are lightly or unused. This research investigates the concept of dynamic topologies, i.e. networks that adapt their topology according to traffic volume. The key aim of this study is to investigate power reductions that can be achieved by dynamic topologies. It proposes a network transformation and introduces mathematical programming models that results in energy optimal topologies for given traffic loads. This paper focuses on the optimisation problems and investigates gains in static environments. Numerical results ar...
In Oslo, traffic has been one of the dominating sources of air pollution in the last decade. In one part of the city where most traffic collects, two tunnels were built. A series of before and after studies was carried out in connection with the tunnels in use. Dispersion models were used as a basis for estimating exposure to nitrogen dioxide and particulate matter in two fractions. Exposure estimates were based on the results of the dispersion model providing estimates of outdoor pollutant concentrations on an hourly basis. The estimates represent concentrations in receptor points and in a square kilometre grid. The estimates were used to assess development of air pollution load in the areas, compliance with air quality guidelines, and to provide a basis for quantifying exposure-effect relationships in epidemiological studies. After both tunnels were taken in use, the pollution levels in the study ...
Based on wind tunnel experiments, theoretical considerations and measurements the dispersion model CAR (Calculation of Air pollution from Road traffic) has been developed for determining air quality in city streets. CAR International is a simple parameterized model using readily available input data and calculating annual percentile values and average concentrations close to streets (at the kerb side) for non-reactive air pollutants and NO{sub 2}. Originally the model was set up for the Dutch situation (traffic, meteorology) with a system of fixed parameters. In order to extend its application to other countries the program has been made more flexible and user friendly. User defined system data can now be changed interactively, such as emission factors of passenger cars and trucks, fraction of directly emitted NO{sub 2}, city and regional background concentration, and average ...
A new prototype model system named AirGIS has been developed to support local authorities in air quality management for big Danish cities. The system is based on the Danish operational street pollution model (OSPM), technical and cadastral digital maps and Danish national administrative databases on buildings, cadastres and populations. It applies a geographic information system (GIS). AirGIS estimates ambient air pollution levels at high temporal and spatial resolutions. The model system enables mapping of traffic emissions, air quality levels and human exposures at residence addresses, at workplace addresses and in streets. Mapping and scenario results can be compared with air quality limits. Impact assessment of traffic air pollution abatement measures can also be carried out. (author)
A simplified stormwater management model has been developed to provide an inexpensive, flexible tool for planning and preliminary sizing of stormwater facilities. The model was developed to be part of a methodology for use in the management of stormwater that utilizes both simple...
Favorable reaction channels are searched for in order to obtain the superheavy element "2"9"8114. The interaction energy is supposed to comply with the adiabatic hypothesis. Concerning the deformation energy, a very complete binary macroscopic-microscopic energy method is used to perform calculations. Deformed two-center shell model provides the energy level schemes for shell effects. Yukawa-plus-exponential model gives the macroscopic (liquid drop) part of the total energy. The mass tensor is obtained by the Werner-Wheeler irrotational flow hypothesis. Finally the minimization of the multidimensional action integral produces the highest penetrability values. Kr-projectile reactions provide the best pairs, although generally the presentabilities are very low. (author)
This paper presents results from a research case study that examined the distribution of travel time of origin-destination (OD) pairs on a transportation network under incident conditions. Using a transportation simulation dynamic traffic assignment (DTA) model, incident on a transportation network is executed under normal conditions, incident conditions without traveler information availability, and incident conditions assuming that users had perfect knowledge of the incident conditions and could select paths to avoid the incident location. The results suggest that incidents have a different impact on different OD pairs. The results confirm that an effective traveler information system has the potential to ease the impacts of incident conditions network wide. Yet it is also important to n...
The Variable Dynamic Testbed Vehicle (VDTV) is presently being developed by the National Highway Traffic Safety Administration (NHTSA). It is being designed to have a steer-by-wire front steering system and an independent rear steering system. These steering systems enable the VDTV to emulate the directional control characteristics of a broad range of passenger vehicles.
We have constructed a mathematical model that describes the coherent spontaneous radiation of a macroscopically filled exciton mode. We have demonstrated qualitatively ways in which a coherent subsystem of excitons can be formed. When this occurs under the influence of an external coherent source, exciton free induction occurs, while in the case of a spontaneous transition of the excitons to a coherent state through freezing of the reservoir of intermolecular interactions superradiance occurs. We have concluded that superradiance in the system of Frenkel excitons is possible under the influence of the non-Dicke mechanisms of self-induction of correlations, when the dipole transition moments of the individual atoms are coupled into a single macroscopic effective spin through their electrostatic interaction, this being analogous to the ordering of magnetic dipole moments in a ferromagnet.
Properties of the multi-species electromagnetic Weibel and electrostatic two-stream instabilities are investigated for an intense ion beam propagating through background plasma. Assuming that the background plasma electrons provide complete charge and current neutralization, detailed linear stability properties are calculated within the framework of a macroscopic cold-fluid model for a wide range of system parameters.
In this article, we describe an approach to model the electromechanical behavior of the skeletal muscle based on the Huxley formulation. We propose a model that complies with a well established macroscopic behavior of striated muscles where force-length, force-velocity, and Mirsky-Parmley properties are taken into account. These properties are introduced at the microscopic scale and related to a tentative explanation of the phenomena. The method used integrates behavior ranging from the microscopic to the macroscopic scale, and allows the computation of the dynamics of the output force and stiffness controlled by EMG or stimulation parameters. The model can thus be used to simulate and carry out research to develop control strategies using electrical stimulation in the context of rehabilitation. Finally, through animal experiments, we estimated model parameters ...
The production of many important commercial materials involves the evolution of a complex fluid through a cooling phase into a hardened product. Textile fibers, high-strength fibers(KEVLAR, VECTRAN), plastics, chopped-fiber compounds, and fiber optical cable are such materials. Industry desires to replace experiments with on-line, real time models of these processes. Solutions to the problems are not just a matter of technology transfer, but require a fundamental description and simulation of the processes. Goals of the project are to develop models that can be used to optimize macroscopic properties of the solid product, to identify sources of undesirable defects, and to seek boundary-temperature and flow-and-material controls to optimize desired properties.
This is a point shapefile showing Traffic sign locations at Colorado National Monument. The coordinates for this dataset were collected using a Trimble Geo-Explorer 2 GPS reciever....
flow and changing scheulingparameters during real-time ..... illustrative purposes, only two minimum separation ..... Individual Flights and Air Traffic, AGARD. No. ...
This paper describes the graphical simulation of a traffic environment. The environment includes streets leading to an intersection, the intersection, vehicle traffic, and signal lights in the intersection controlled by different methods. The simulation allows for the study of parameters affecting traffic environments and the study of different control strategies for traffic signal lights, including conventional, fuzzy, and adaptive control methods. Realistic traffic environments are simulated including a cross intersection, with one or more lanes of traffic in each direction, with and without turn lanes. Vehicle traffic patterns are a mixture of cars going straight and making right or left turns. The free velocities of vehicles follow a normal distribution with a mean of the ``posted`` speed limit. Actual velocities depend on such factors ...
It is suggested that the model of a neutrino ball described in terms of the standard model extended by adding right-handed neutrinos and the Majorana scalar field can be presented in order to explain a body of weak interacting neutrinos. Neutrino interaction with the scalar Majorana field violates the lepton number and produces the mass splitting of neutrino due to the sea-saw mechanism. In this model a neutrino ball is an object which appears as a result of a first order cosmological phase transition. It can be regarded as a ball filled with Dirac neutrinos and can be treated as a remnant of the phase transition with unbroken global lepton symmetry. In this paper we study the macroscopic parameters of such a configuration. In the result the mass-radius curve M(R) for this object is obtained. (orig.).
Traffic characterization is an important means for Internet Service Providers (ISPs) to adapt and to optimize their networks to the requirements of the customers. Most network measurements are performed in the backbone of these ISPs, showing both, residential and business Internet traffic. However, the traffic characteristics of business and home users differ significantly. Therefore, we have performed measurements of home users at a broadband wireless access service provider in order to reflect only home user traffic characteristics. In this paper, we present the results of these measurements, showing daily traffic fluctuations, flow statistics as well as application distributions. The results show a difference to backbone traffic characteristics. Furthermore, we observed a shift from web...
The emission of air pollutants from road vehicles is the most significant source of air pollution in towns. The chemical composition of these pollutive substances is dependent on the fuel, the type of vehicle and the character of the traffic system. The pollution concentration was measured, (nitrogen oxides and carbon monoxide) in relation to each type of vehicle, in four streets in the Copenhagen area. The system of measurement used was the ''Operational Street Pollution Model'' (OSPM). Results are presented in the form of tables and charts. (AB) 11 refs.
Kerf geometry, kerf wall features, and cutting front characteristics of an Abrasive Waterjet (AWJ) machined Graphite/Epoxy (Gr/Ep) laminate were studied. A macroscopic analyses suggests that geometrical features associated with AWJ machining of Gr/Ep laminates are influenced by three macro regions along the cutting depth. The presence of these regions, including initial damage at jet entry, smooth cutting, and rough cutting near the jet exit, depends on the operating conditions. Design of experiments and analysis of variance were used to determine the effect of cutting parameters on kerf characteristics and to develop empirical models for kerf profile and features of the three distinct macroscopic regions. Cutting front analysis revealed that the mechanisms of material removal in AWJ machining of Gr/Ep do not change over the jet penetration depth. In general, high quality uniform cuts may be obtained by minimizing initial ...
Liquid-liquid wetting failure is investigated in a two-dimensional Couette system with two immiscible fluids of arbitrary viscosity. The problem is solved exactly using a sharp interface treatment of hydrodynamics (lubrication theory) as a function of the capillary number, viscous ratio and separation of scale, i.e. slip length versus macroscopic scale of the system. The existence of critical velocities, above which no stationary solutions are found, is analyzed in detail in terms of the relevant parameters of the system. Comparisons with existing analysis for other geometries are also carried out. A numerical method of analysis is also presented, based on diffuse interface models obtained from multiphase extensions of the lattice Boltzmann equation (LBE). Sharp interface and diffuse interface models are quantitatively compared face to face indicating the correct limit of applicability of the diffuse interface ...
The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0{sup +}{yields}2{sup +} transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: {sup 18}O, {sup 30}Si, {sup 32,34}S, {sup 48}Ca, {sup 88}Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.
The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0"+#->#2"+ transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: "1"8O, "3"0Si, "3"2","3"4S, "4"8Ca, "8"8Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.
We develop a large scale parallel viscous-elastic analysis program incorporating a mesoscopic self-consistent model developed by Laws. In the model, macroscopic elastic constants are treated as variables depending on the shape and statistical properties of pre-existing microscopic pores and change due to neutron irradiation. We apply this program to the visco-elastic analysis of nuclear graphite structures under neutron irradiation environment in High Temperature Gas-cooled Reactor (HTGR), as an example problem. Furthermore the calculated results by this parallel computational program are compared with those by one of commercial finite element analysis codes, FINAS, for validating elastic and thermal stress analysis function. (author)
The flexibility of bus rapid transit (BRT) in scheduling is one of the greatest differences with traditional buses. In order to improve BRT operation quality, the paper studied the headway optimization and scheduling combination of BRT vehicles. A model has been established to minimize passengers travel costs and vehicles operation cost, and constraints included passenger volume, time, and frequency. The scheduling combination was composed by normal, zone, and express scheduling. The model was solved by genetic algorithm of variable-length coding. The result of the numerical case shows that: the optimization results can save 69.92% cost. The sensitivity analysis shows that, under higher traffic volume or lower speed, the travel cost can be reduced through reasonable scheduling combination....
Full text of publication follows: General simulation objectives of any fire analysis are macroscopic in nature and deals with the grass data in respect of fire/smoke spread, structural behaviour, environmental conditions etc. However, the accuracy of predicting such macroscopic parameters is a strong function of several other microscopic parameters which govern the overall macroscopic behaviour. Some of the microscopic parameters of interesting such analysis could be buoyancy induced stable/unstable flows, relative flame behaviour, baroclinic velocity distribution etc. Only the field based fire modelling approach is capable of calculating several of these by way of detailed CFD based field modelling. One of the best known tool that could be employed for such studies is the Fire Dynamics simulator (FDS) from NIST with its popular LES based fire modelling ...
Data and functions of the cell burnup calculation of the SRAC system were revised to improve mainly the accuracy of the burnup calculation of high conversion light water reactors (HCLWRs). New burnup chain models were developed in order to treat fission products (FPs) and actinide nuclides in detail. Group cross section library, SRACLIB-JENDL2, was generated based on JENDL-2 nuclear data file. In generating this library, emphasis was placed on FPs and actinides. Also revised were the data such as the average energy release per fission for various actinides. These improved data were verified by performing the burnup analysis of PWR spent fuels. Some new functions were added to the SRAC system for the convenience to yield macroscopic cross sections used in the core burnup process. (author).
The dependence of the carrier concentrations, of the resistivity and of the Hall coefficient of irradiated silicon on the neutron fluences has been investigated, starting from the supposition that the main phenomena induced by irradiation in the semiconductor bulk are shallow-donor removal and deep-centres creation. The free parameters of the model are initial doping of the starting material, the permitted energy level values of the radiation-induced centres in the semiconductor band gap and their introduction rates. The influence of each parameter on the calculated dependences is studied in detail, for three cases: one deep acceptor-like centre, two deep acceptors and one deep acceptor plus one deep donor-like centre. each of the three cases is discussed in correspondence with different experimental results.
In this work, a comprehensive model including heat transfer, fluid flow and solidification was used to evaluate the performance of a novel delivery system for a single-belt steel casting process. This near-net-shape casting, although still in development, is one of the most promising routes for casting of low-carbon steel in large scale. This paper focuses on the performance of a low-Re {kappa}-{epsilon} model that was employed to simulate the three-dimensional turbulent flows fully-coupled with heat transfer and macroscopic solidification. Simulations were run for the intended conditions of caster operation, and the results obtained with the {kappa}-{epsilon} were compared with the results obtained with an ad hoc viscosity model, where the molecular viscosity was boosted 100 times, uniformly throughout the computational domain. A semi-analytical solution was employed for validating the ...
This study addresses the modeling of transdermal diffusion of drugs, to better understand the permeation of molecules through the skin, and especially the stratum corneum, which forms the main permeation barrier of the skin. In transdermal delivery of systemic drugs, the drugs diffuse from a patch placed on the skin through the epidermis to the underlying blood vessels. The epidermis is the outermost layer of the skin and can be further divided into the stratum corneum (SC) and the viable epidermis layers. The SC consists of keratinous cells (corneocytes) embedded in the lipid multi-bilayers of the intercellular space. It is widely accepted that the barrier properties of the skin mostly arises from the ordered structure of the lipid bilayers. The diffusion path, at least for lipophilic molecules, seems to be mainly through the lipid bilayers. Despite the advantages of transdermal drug delivery compared to other drug delivery routes such as oral dosing and ...
Various phenomenological theories of wave-type heat transport, which can be interpreted as the models of an isotropic rigid heat conductor with an internal vector state variable, have been proposed in the literature with the objective to describe the second sound propagation in dielectric crystals. The aim of this paper is to analyze the relation between these phenomenological approaches and the phonon gas hydrodynamics. The four-moment phonon gas hydrodynamics based on the maximum entropy closure of the moment equations with nonlinear isotropic phonon dispersion relation is considered for this purpose. We reformulate the equations of this hydrodynamics in terms of energy and quasi-momentum as the primitive fields and subsequently demonstrate that, from the macroscopic point of view, they can be understood as describing the reference model of an isotropic rigid heat conductor with quasi-momentum playing the role of the ...
Russian field surgery with its long history and distinctive characteristics has accumulated great experience in the long-time practice of warfare. Chinese field surgery was established and developed on the basis of studying from the Russian model, which opened up new areas of traffic medicine, molecular traumatology and assessment of biological effects on weapon destruction and carried out in-depth research on wound ballistics, blast injury, burns and combined injury etc. through decades of construction with continuous development and innovation, and a series of major achievements have been made in these fields. By making comparative study on the historical evolution, structure system, characteristics of campaigns and development of society between Chinese and Russian field surgery, it can be found that there are great gaps between them and we should strengthen the research for more rapid development. PMID:20510098
In the frame of the comprehensive assessment of Swiss energy systems, air quality simulations were performed by using a 3-dimensional photo-chemical dispersion model. The objective is to investigate the impacts of pollutants in Switzerland for future options of Swiss energy systems. Four scenarios were investigated: Base Case: simulations with the projected emissions for the year 2030, Scenario 1) all nuclear power plants were replaced by oil-driven combined cycle plants (CCP), Scenarios 2 to 4) traffic emissions were reduced in whole Switzerland as well as in the cities and on the highways separately. Changes in the pollutant concentrations and depositions, and the possible short-term impacts are discussed on the basis of exceedences of critical levels for plants and limits given to protect the public health. (author) 2 figs., 7 refs.
Multi-fiber WDM networks are becoming the major telecommunication platforms for transmitting exponentially increasing data traffic. While today's networks are mainly providing circuit-switched connections, optical packet-switching technologies have been investigated for years, aiming at achieving more efficient utilizations of network resources. In this paper, we have evaluated, for the first time, the packet-loss performance of multi-fiber optical packet switches (MOPS). Our main contributions are threefold. Firstly, we have proposed simple and accurate analytical models for analyzing packet-loss performance of (i) the most fundamental MOPS configuration, (ii) MOPS equipped with fiber delay lines (FDLs) and (iii) shared wavelength converters (SWCs). Secondly, we have shown that the MOPS n...
ObjectivesThe development of novel formulations of nanoparticles in the nanotechnology industry and their increasing importance and use in industry means there is certainty of human environmental exposures in both the workplace and the general environment. The pulmonary route of exposure to airborne nanoparticles is a major one, as nanoparticles are handled in industry, escape from workplaces and products containing nanoparticles undergo attrition in the environment. There is a substantial problem for ris [continued...]DescriptionNanoparticles are extremely small particles, each individual particlel being less than one ten millionth of a metre in size. We are exposed to nanoparticles in busy streets as they are present in traffic exhaust produced from combustion of fuel and such nanoparticles are considered to be important in causing the harmful effects associated with exposure to air pollution. There are other situations where nanoparticles are found in the air, ...
BackgroundRoad traffic crashes are considered by the WHO to be the most important global cause of death from injury. However, this may not be true for large areas of rural Asia where...Full Text Available
Skip to Main Content Skip to Main Navigation National Highway Traffic Safety Administration Accessible menu--Sitemap Driving Safety Aggressive Driving Bicycles Child Safety...
Noise pollution from human traffic networks and industrial activity impacts vast areas of our planet. While anthropogenic noise effects on animal communication are well documented, we have very limited...Full Text Available
separation and arrival planning to the Air Traffic Service Providers (ATSP). ... a safe, highly efficient flow of traffic from enroute into TRACON airspace that reliably ..... AGARD Lecture Series 200 Presentation, Madrid, Spain, Paris, France, and ...
Purpose - The purpose of this paper is to develop pansystems-styled traffics, logistics and knowledge rediscovery. The core logoi are the generalized resources//F* and their circulation//C*. The research presents a new outlook to mathematics, physics, traffic, communication, logistics, KD, internet, computer, translation, simulation, information, life-systems, logic or reasoning, memory or storage, process, transaction, finance, education, inherent, topology, evolution, etc. and then certain mechanism among them and related mutuality can be unveiled. Design/methodology/approach - A flexible combination of philosophy, mathematics and technology is embodied. The paper is an application of pansystems methodology to approach the following topics: pansystems resource, circulation: traffics, log...
Objective: : Evaluate expression of inducible negative regulators of JAK/STAT pathway and their target proteins during the course of ligature-induced experimental periodontal disease in rats. Design: : Rats were sacrificed 07, 15 and 30days after disease induction for histological evaluation of periodontal inflammation and macroscopic analysis of alveolar bone loss. SOCS expression and the activation status of STAT1 and STAT3 were evaluated in gingival biopsies by real time PCR and Western blot. Results: : Ligature-induced model presented significant progressive bone loss from 7 to 30days. Inflammation was evident and similar for 07 and 15days; however, a decrease on severity at the end of the experimental period was observed. There was a significant (p<0.05) increase on SOCS1 and SOCS3 ge...
Reduction of the metallic impurity concentration in the TCA plasma has enabled us to correlate the observed heating with the calculated position where the rf energy is deposited. In modelling the measured antenna loading due to the presence of Alfven resonance surfaces, and hence inferring the energy deposition profile, both ion cyclotron effects and the toroidal geometry must be considered. In particular, toroidicity couples energy to resonance surfaces that would not be excited in cylindrical geometry. The increase in electron density during a rf pulse changes the positions of these surfaces so that spectrum-related effects may be observed. The appearance of a new surface at the centre of the plasma is seen as a sharp discontinuity on many of the macroscopic parameters, accompanied by evidence of changes in the current density profile. These results, and the predictions of numerical codes, have imposed new constraints on the optimisation of ...
We present results of multiple-time-scale simulations of 5, 10 and 15 keV low temperature ion implantation of arsenic on silicon (100), followed by high temperature anneals. The simulations start with a molecular dynamics (MD) calculation of the primary state of damage after 10ps. The results are then coupled to a kinetic Monte Carlo (MC) simulation of bulk defect diffusion and clustering. Dose accumulation is achieved considering that at low temperatures the damage produced in the lattice is stable. After the desired dose is accumulated, the system is annealed at 800 degrees C for several seconds. The results provide information on the evolution for the damage microstructure over macroscopic length and time scales and affords direct comparison to experimental results. We discuss the database of inputs to the MC model and how it affects the diffusion process.
An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the ...
A numerical study has been performed to investigate the hydrodynamic aspects of the pool boiling on horizontal-, vertical- and downward-facing surfaces. The FlowLab code, which is based on a Lattice-Boltzmann (LB) model of two-phase flows, is employed. Macroscopic properties, such as surface tension ({sigma}) and contact angle ({beta}), are implemented through the fluid-fluid (G{sub {sigma}}) and fluid-solid (G{sub t}) interaction potentials. The model is found to express a linear relation between the macroscopic properties ({sigma}, {beta}) and microscopic parameters (G{sub {sigma}}, G{sub t}). The simulation results on bubble departure diameter appear to have the same parametric dependence as the empirical correlation. Hydrodynamic aspects of two-phase flow regime transition mechanism are investigated for different surface-coolant configurations. Results of the LB simulation clearly demonstrate that ...
The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. ...
Sufficient passing sight distance is an important control for two-lane rural highway design to minimize the possibility of a head-on collision between passing and opposing vehicles. Traditionally, passing zones are marked by checking passing sight distance that is potentially restricted by static sight obstructions. Such obstructions include crest curves, overpasses, and lateral objects along highways. This paper proposes a new concept of dynamic sight-distance assessment, which involves restricted passing sight distances due to the impeding vehicles that are traveling in the same direction. Using a finite-element model, the dynamic passing sight-distance problem was evaluated, and the writers analyzed the relationships between the available passing sight distance and other factors such as the horizontal curve radius, impeding vehicle dimensions, and a driver s following distance. It was found that the impeding vehicles may cause substantially insufficient passing ...
We have developed a kinetic Monte Carlo (kMC) simulator that links atomic migration and binding energies determined primarily from first principles calculations to macroscopic phenomena and laboratory time scales. Input for the kMC simulation is obtained from a combination of ab initio planewave pseudopotential calculations, molecular dynamics simulations, and experimental data. The simulator is validated against an extensive series of experimental studies of the diffusion of B spikes in self-implanted Si. The implant energy, dose, and dose rate, as well as the detailed thermal history of the sample, are included. Good agreement is obtained with the experimental data for temperatures between 750 and 950 C and times from 15 to 255 s. At 1050o C we predict too little diffusion after 105 s compared to experiment: apparently, some mechanism which is not adequately represented by our model becomes important at this temperature. Below 1050o C, the ...
Differential cross sections for 201.5 MeV proton scattering form /sup 88/Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good ...
Differential cross sections for 201.5 MeV proton scattering form "8"8Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good description ...
n an early approach, we proposed a kinetic model with multiple translational temperature [K. Xu, H. Liu and J. Jiang, Phys. Fluids {\\bf 19}, 016101 (2007)], to simulate non-equilibrium flows. In this paper, instead of using three temperatures in $x-$, $y-$, and $z$-directions, we are going to further define the translational temperature as a second-order symmetric tensor. Based on a multiple stage BGK-type collision model and the Chapman-Enskog expansion, the corresponding macroscopic gas dynamics equations in three-dimensional space will be derived. The zeroth-order expansion gives the 10 moment closure equations of Levermore [C.D. Levermore, J. Stat. Phys {\\bf 83}, pp.1021 (1996)]. To the 1st-order expansion, the derived gas dynamic equations can be considered as a regularization of Levermore's 10 moments equations. The new gas dynamic equations have the same structure as the Navier-Stokes equations, but the stress ...
Soil contamination by liquid organic pollutants represents a serious threat to phreatic ground water. These organic liquids get into the ground and migrate through the porous medium until they finally reach the aquifer. After a critical study of the literature, we listed various existing multiple displacements under three-phase conditions of a disconnected polluting phase that may or not spread over water. The aim of this thesis is to model (at pore scale level) and integrate in the pore network model the various flows that occur when three phases (gas, pollutant and air) are present in a porous medium. The porous medium is supposed completely water-wet. The polluting phase may be connected or not, and the spreading coefficient of the pollutant over water may either be positive or negative. The goal of our study is to obtain macroscopic parameters such as relative permeabilities and capillary pressure. These parameters can ...
Leaded gasoline has been used as fuel for trucks and automobiles in the United States since 1924; it has been implicated as a source of lead that is deposited on the soil and eventually can be ingested by small children, contributing to their burden of this toxic metal. The lead content of 667 surface-soil samples (taken at depths of 0-5 cm) and 159 subsurface-soil samples (from depths of 25-30 cm) collected from Illinois play areas near roads was measured and related to traffic variables. The samples were collected between June and October of 1985, and their measured lead levels exceeded the average natural background level for Illinois soil. The highest lead concentrations were found in samples from the six-county metropolitan Chicago region, where both traffic volume and traffic density are higher than in the rest of the state. Regression analysis showed significant correlation of lead concentration in the top 5 cm of ...
voluntarily provided by you. Network Traffic Logs In the course of ensuring network security and consistent service for all users, the University employs software programs to...
Multifractal detrended cross-correlation analysis (MF-DXA) has been developed to detect the long-range power-law cross-correlation of considered signals in the presence of non-stationarity. However, crossovers arising from extrinsic periodic trends make the scaling behavior difficult to analyze. We introduce a Fourier filtering method to eliminate the trend effects and systematically investigate the multifractal cross-correlation of simulated and real traffic signals. The crossover locations are found approximately corresponding to the periods of underlying trend. Traffic velocity on one road and flows on adjacent roads show strong cross-correlation. They also present weak multifractality after periodic trends are removed. The traffic velocity and flow are cross-correlated in opposite directions which is accordant to their actual evolution.
Jan 31, 2002 ... Sequential Flow of EDA Functionality for Flow with Separation ...... for Automated Air Traffic Management," AGARD Lecture Series No. ...
During a high speed road traffic accident, a 26-year-old man suffered multiple fractures of his thoracic vertebrae and bilateral pneumothoraces. The day after admission and commencement of nasogastric...Full Text Available
BackgroundThe purpose of this research was to examine whether waterpipe smokers experience increased risk of motor vehicle crashes.MethodsIn a telephone...Full Text Available
airborne separation assistance systems (ASAS) to ... operations should be limited to the outer traffic flow ...... AGARD Meeting on Machine Intelligence in Air ...
... adaptive method called Shortest Queue plus Bias ... routing problem under stochastic traffic demands have ... of permits allocated to a node or terminal ...
The effect of one on-ramp (entry) and one off-ramp (exit) is investigated numerically in one dimensional-cellular automaton traffic flow model, with open boundary conditions, using parallel dynamics. Our aim in this paper is to study how the injecting rates $\\alpha$ and $\\alpha_{0}$ and the extracting rates $\\beta$ and $\\beta_{0}$ acts on the density and flux of cars in one dimensional road. The priority of occupation at entry site $i_{1}$ (moving at exit site $i_{2}$) is attributed to the particle which entered (absorbed) in the chain. Phase diagrams in ($\\beta_{0},\\alpha_{0}$), and ($\\beta,\\alpha_{0}$) plans are established. For $\\alpha=0.1$, they show three different topologies in the flow behaviour. The first one correspond to the presence of four regions, by varying $\\alpha_{0}$; namely low density phase (LDP), intermediate density phase (IDP), plateau current phase (PCP) and high density phase (HDP). In the second topology the ...
This presentation gives the results of a research programme aimed at evaluating exhaust emissions from ships moving within confined coastal zones, as in Piraeus harbour. The level of various exhaust emissions were estimated on the basis of a mathematical model applied for each sea traffic element (ship). Hourly and daily records of all ships` movements in different parts of the harbour were compiled, covering extended periods of time and associated with different shipping operational characteristics (peaks, lows, etc). In order to correlate the exhaust emissions from shipping with the quality of the air in the area of interest, land-based measurements for the same pollutants were carried out in selected locations, near the port and in the greater Athens area. This enabled the investigation of time and spatial diffusion of exhaust emissions from shipping within the area of interest, taking into account the influence of prevailing meteorological ...
The mission of the Emerging Technologies thrust area at Lawrence Livermore National Laboratory is to help individuals establish technology areas that have national and commercial impact, and are outside the scope of the existing thrust areas. We continue to encourage innovative ideas that bring quality results to existing programs. We also take as our mission the encouragement of investment in new technology areas that are important to the economic competitiveness of this nation. In fiscal year 1992, we have focused on nine projects, summarized in this report: (1) Tire, Accident, Handling, and Roadway Safety; (2) EXTRANSYT: An Expert System for Advanced Traffic Management; (3) Odin: A High-Power, Underwater, Acoustic Transmitter for Surveillance Applications; (4) Passive Seismic Reservoir Monitoring: Signal Processing Innovations; (5) Paste Extrudable Explosive Aft Charge for Multi-Stage Munitions; (6) A Continuum Model for Reinforced Concrete ...
The automotive paints could be generally differentiated by color, layer sequence and chemistry of the paint layers comprising each of the topcoat and the primer system. The successful identification of hit-and-run a and traffic accidental vehicles from evidential paint fragments is greatly facilitated with a comprehensive laboratory collection of reference paint samples and the technique for direct analysis without sample preparation. The Pyrolysis-Gas Chromatography(PGC) is a precise and reliable method for performing both quantitative and qualitative analysis of polymeric materials and forensic samples. Our Forensic Laboratory is conducting the examination and identification of 73 reference paint samples; 4 colors of each domestic automotive make that is poplar in Korea, by Curie Point Pyrolyzer(JHP-3) and GC with capillary column(ultra alloy-5). This method can be used not only to compare paint traces with their suspected sources, but also to identify the type, ...
The authors describe the development of a four-dimensional atlas and reference system that includes both macroscopic and microscopic information on structure and function of the human brain in persons...Full Text Available
A calculation program (URA 6.F4) was elaborated on FORTRAN IV language, that through finite differences solves the unidimensional scalar Helmholtz equation, assuming only one energy group, in spherical cylindrical or plane geometry. The purpose is the determination of the flow distribution in a reactor of spherical cylindrical or plane geometry and the critical dimensions. Feeding as entrance datas to the program the geometry, diffusion coefficients and macroscopic transversals cross sections of absorption and fission for each region. The differential diffusion equation is converted with its boundary conditions, to one system of homogeneous algebraic linear equations using the box integration technique. The investigation on criticality is converted then in a succession of eigenvalue problems for the critical eigenvalue. In general, only is necessary to solve the first eigenvalue and its corresponding eigenvector, employing the power method. The obtained results by ...
The detailed formulation for loop quantum cosmology (LQC) in the Bianchi I model with a scalar massless field has been constructed. In this paper, its effective dynamics is studied in two improved strategies for implementing the LQC discreteness corrections. Both schemes show that the big bang is replaced by the big bounces, which take place up to three times, once in each diagonal direction, when the area or volume scale factor approaches the critical values in the Planck regime measured by the reference of the scalar field momentum. These two strategies give different evolutions: In one scheme, the effective dynamics is independent of the choice of the finite sized cell prescribed to make Hamiltonian finite; in the other, the effective dynamics reacts to the macroscopic scales introduced by the boundary conditions. Both schemes reveal interesting symmetries of scaling, which are reminiscent of the relational interpretation of quantum ...
High-energy ionizing radiation is a prominent modality for the treatment of many cancers. The approaches to electron dose calculation can be categorized into semi-empirical models (e.g. Fermi-Eyges, convolution-superposition) and probabilistic methods (e.g. Monte Carlo). A third approach to dose calculation has only recently attracted attention in the medical physics community. This approach is based on the deterministic kinetic equations of radiative transfer. We derive a macroscopic partial differential equation model for electron transport in tissue. This model involves an angular closure in the phase space. It is exact for the free streaming and the isotropic regime. We solve it numerically by a newly developed HLLC scheme based on Berthon et al (2007 J. Sci. Comput. 31 347-89) that exactly preserves the key properties of the analytical solution on the discrete level. We discuss several test cases ...
An important opportunity for solving future traffic problems lies in a change of the connection existing between traffic growth and economic development. It could help bring about a cut in traffic intensity. This can be achieved by rationalizing transport processes, i.e. by enhancing the efficiency of traffic via improved organization and infrastructure. Rationalization means that a given traffic effort (distance in kilometres, time, route, energy) can yield a higher transport effect, or a certain transport effect can be attained with less traffic effort. Enhanced productivity permits more transport without more traffic-related and environmental nuisances. (orig.) [Deutsch] Ein wichtiger Weg zur Loesung der kuenftigen Verkehrsprobleme liegt in der Veraenderung des Zusammenhangs der zwischen Verkehrswachstum und Wirtschaftsentwicklung ...
As part of the Wisconsin road weather safety initiative, the objective of this study is to assess the effects of rainfall on the severity of single-vehicle crashes on Wisconsin interstate highways utilizing polychotomous response models. Weather-related factors considered in this study include estimated rainfall intensity for 15 min prior to a crash occurrence, water film depth, temperature, wind speed/direction, stopping sight distance and deficiency of car-following distance at the crash moment. For locations with unknown weather information, data were interpolated using the inverse squared distance method. Non-weather factors such as road geometrics, traffic conditions, collision types, vehicle types, and driver and temporal attributes were also considered. Two types of polychotomous response models were compared: ordinal logistic and sequential logistic regressions. The sequential logistic regression was tested with ...
Because of the stochastic nature of traffic requirement matrix, it is very difficult to get the optimal traffic distribution to minimize the delay even with adaptive routing protocol in a fixed connection network where capacity already defined for each link. Hence there is a requirement to define such a method, which could generate the optimal solution very quickly and efficiently. This paper presenting a new concept to provide the adaptive optimal traffic distribution for dynamic condition of traffic matrix using nature based intelligence methods. With the defined load and fixed capacity of links, average delay for packet has minimized with various variations of evolutionary programming and particle swarm optimization. Comparative study has given over their performance in terms of converging speed. Universal approximation capability, the key feature of feed forward neural network has applied to predict ...
The macroscopic behavior of magnetostrictive materials results from domain evolutions occurring at a microscopic scale. The author shows how to compute magnetization and magnetostriction curves by appraising the behavior of the underlying microstructures. The method hinges on an averaging device (Young measures), which allows one to pass from the microscopic to the macroscopic scale. He takes into account the kinematical constraints on the accommodation of elastic effects, and he highlights the role of material symmetry in the selection of energetically optimal microstructures.
We investigate the dynamics of an 11-dimensional homogeneous cosmological model. We assume that the t = const hypersurfaces are products of a 3-dimensional Bianchi type-IX space and a 7-dimensional torus. Most results of our investigation hold when the 7-dimensional torus is replaced by an m-dimensional torus T/sup m/. We show that for a large class of vacuum solutions the physical space expands while the microspace contracts providing a natural mechanism of dimensional reduction. Matter satisfying a simple barotropic equation of state always breaks the process of dynamical dimensional reduction. With special attention we study the behavior of our model close to the initial singularity. In contrast with the 4-dimensional Bianchi type-IX cosmological model the Kasner solution always describes an approach to the initial singularity. We study the transition from the Kasner regime to the oscillatory regime. We show that matter ...
We investigate the dynamics of an 11-dimensional homogeneous cosmological model. We assume that the t = const hypersurfaces are products of a 3-dimensional Bianchi type-IX space and a 7-dimensional torus. Most results of our investigation hold when the 7-dimensional torus is replaced by an m-dimensional torus T/sup m/. We show that for a large class of vacuum solutions the physical space expands while the microspace contracts providing a natural mechanism of dimensional reduction. Matter satisfying a simple barotropic equation of state always breaks the process of dynamical dimensional reduction. With special attention we study the behavior of our model close to the initial singularity. In contrast with the 4-dimensional Bianchi type-IX cosmological model the Kasner solution always describes an approach to the initial singularity. We study the transition from the Kasner regime to the oscillatory regime. We show that matter ...
The work described in the following is a portion of the MEET project (Methodologies for Estimation Air Pollutant Emissions from Transport). The overall goal of the MEET project is to consolidate and present methodologies which can be used to estimate air pollutant emissions from various types of traffic sources. One of the goals of MEET is to provide methodologies to be used in the COMMUTE project also funded by DG VII. COMMUTE is developing computer software which can be used to provide emissions inventories on the European scale. Although COMMUTE is viewed as a prime user of the information generated in MEET, the MEET results are intended to be used in a broader area, and on both smaller and larger spatial scales. The methodologies and data presented will be useful for planners on a more local scale than a national or continental basis. While most attention in previous years has been concentrated on emissions from road transport, it has become increasingly ...
We briefly reviewed and summarized the experimental study on {beta}-delayed proton decays published by our group over the last 8 years, namely the experimental observation of {beta}-delayed proton decays of nine new nuclides in the rare-earth region near the proton drip line and five nuclides in the mass 90 region with N{approx}Z by utilizing the p-{gamma} coincidence technique in combination with a He-jet tape transport system. In addition, important technical details of the experiments were provided. The experimental results were compared to the theoretical predictions of some nuclear models, resulting in the following conclusions. (1) The experimental half-lives for {sup 85}Mo, {sup 92}Rh, as well as the predicted 'waiting point' nuclei {sup 89}Ru and {sup 93}Pd were 5-10 times longer than the macroscopic-microscopic model predictions of Moeller et al. [At. Data Nucl. Data Tables 66,131(1997)]. These ...
The experimental study on #beta#-delayed proton decays near the proton drip line published by our group over the last 8 years were reviewed and summarized briefly, including first observation of 9 precursors in the rare-earth region and new measurements of 5 nuclei in the mass-90 region near N-Z line with the aid of the 'p-#gamma#' coincidence in combination with a He-jet tape transport system. Systematically comparing the experimental data with the current nuclear-model predictions, following points were represented. (1) the experimental half-lives for "8"5Mo and "9"2Rh as well as the predicted 'waiting point' nuclei "8"9Ru and "9"3Pd are 5-10 times longer than the macroscopic-microscopic model predictions given by Moeller et al. It considerably influences the prediction of mass abundances of the nuclides produced in rp-process. (2) The current-model predictions are not consistent with the experimental ...
We briefly reviewed and summarized the experimental study on #beta#-delayed proton decays published by our group over the last 8 years, namely the experimental observation of #beta#-delayed proton decays of nine new nuclides in the rare-earth region near the proton drip line and five nuclides in the mass 90 region with N#approx#Z by utilizing the p-#gamma# coincidence technique in combination with a He-jet tape transport system. In addition, important technical details of the experiments were provided. The experimental results were compared to the theoretical predictions of some nuclear models, resulting in the following conclusions. (1) The experimental half-lives for "8"5Mo, "9"2Rh, as well as the predicted 'waiting point' nuclei "8"9Ru and "9"3Pd were 5-10 times longer than the macroscopic-microscopic model predictions of Moeller et al. [At. Data Nucl. Data Tables 66,131(1997)]. These data considerably influenced the ...
... in an incinerating toilet; and, resulting ash would be retrograded from Antarctica via McMurdo ... toilet would be used with resultant ash retrograded from Antarctica. 11. Would the proposed activity ...
The report deals with the energy consumption of traffic and its emissions of hazardous substances into the air, and stresses the advantages of the electric car with respect to energy consumption and noise generation. 5 figs., 3 refs.
We presented data showing that the CART-19 cells expressing the 4-1BB signaling domain can have unprecedented and massive in-vivo expansion, traffic to tumor sites, persist long term in vivo, and induce...Full Text Available
Background: The objective of this study was to assess the factors associated with the traffic mortality in the region of Central Macedonia in order to produce evidence in building up preventive...Full Text Available
BackgroundTraffic injuries can cause physical, psychological, and economical impairment, and affected individuals may also experience shortcomings in their post-accident care and...Full Text Available
The airborne traffic monitoring system forms a novel technology of detecting vehicle motion. An optical digital camera located on an airborne platform produces a series of images which then are processed to recognized the fixed vehicles. In this way the video data are converted into the time sequence of frames containing the vehicle coordinates. In the present work a three-frame algorithm is developed to identify the succeeding vehicle positions. It is based on finding the neighboring points in the frame sequence characterized by minimal acceleration. To verify and optimize the developed algorithm a ``Virtual Road'' simulator was created. Finally available empirical data are analyzed using the created algorithm.
Many mobile ad hoc network protocols use simple flooding, in order to adapt to changes in time varying network topology. Most of the times, a network-wide flood results in redundant packets and increases network congestion, probability of packet collision, low utilization of available bandwidth, and most important, higher power consumption. In this paper, we propose a new cross-layer broadcast scheme to minimize broadcast traffic in mobile ad hoc networks. Our scheme is based on use of received signal strength indicator, RSSI, value to reduce the number of broadcast packets. The effectiveness of the proposed technique is verified using simulations.
11-MeV neutrons were elastically and inelastically scattered from eight single-closed-shell nuclei: three proton-vibrational nuclei with N = 50 ("8"8Sr, "9"0Zr, "9"2Mo) and five even-even neutron-vibrational nuclei ("1"1"6"-"1"2"4Sn) with Z = 50. Detection methods involving electronic discrimination against #gamma# rays, and time-of-flight techniques were used to measure the energy of the scattered neutrons. Data were taken from 15"0 to 150"0 in 5"0 intervals. Measured differential cross sections were normalized to the zero-degree neutron flux and corrected. An optical model (OM) analysis was used to fit the elastic data with the code GENOA, and potential parameters were obtained for each nucleus. The observed low-lying electric quadrupole (2"+) and octupole (3"-) states were collective in nature; the macroscopic or collective model for inelastic scattering was used to generate the differential cross-section angular ...
Modern high-resolution electron microscopy (HREM) instruments, which are capable of a point-to-point resolution of better than 0.2 nm, have allowed atomic-scale observations of a variety of internal interfaces. The application of the HREM technique to fcc model systems for the purpose of addressing a number of interface issues will be examined in this paper. Atomic structure observations for heterophase interfaces of metal/metal and metal/metal-oxide systems as well as HREM studies of grain boundaries in NiO and Au will be discussed with emphasis on generic structural features and the role of the interface plane. Comparisons between observed interface structures and atomistic computer modeling results have shown agreements for some interfaces, as well as certain differences in others. A number of structural features are common to both metal and oxide grain boundaries, as well as certain heterophase boundaries. Of particular importance in ...
Secreted human bronchial mucins, directly collected from macroscopically healthy bronchial mucosa, were prepared in the presence of six proteinase inhibitors, and analysed by electron microscopy. These...Full Text Available
The macroscopic stress distribution across an annealed Zircaloy-4 gas tungsten arc weld was measured by neutron time-of-flight diffraction at the SMARTS diffractometer at Los Alamos National Laboratory. The stresses after annealing are about 40% lower than those in the same weld prior to heat treatment. The intergranular strains in the reference coupons, which give the macroscopic stress free lattice spacings, are consistent with the difference in cooling the strongly textured plate and the weakly textured weld.
Abstract Simon Saunders and David Wallace have proposed an attractive semantics for interpreting linguistic communities embedded in an Everettian multiverse. It provides a charitable interpretation of our ordinary talk about the future, and allows us to retain a principle of bivalence for propositions and to retain the law of excluded middle in the logic of propositions about the future. But difficulties arise when it comes to providing an appropriate account of the metaphysics of macroscopic objects and events. I evaluate various metaphysical frameworks which might be combined with the Saunders-Wallace semantics. I conclude that the most appropriate metaphysics to underwrite the semantics renders Everettian quantum mechanics a theory of non-overlapping worlds.
Canadian railway traffic is delayed until lines are plowed of snow following heavy snowfalls. A modification that would permit higher plowing speeds and fewer delays could realize significant benefits in addition to direct fuel and labor savings. The objective of this project was to carry out a cost benefit analysis on a low-friction coating applied to a mainline railway snow plow. The assessment was carried out using old Canadian National Railway snow plows for test purposes. An analytical model was developed to estimate the importance of friction reduction to fuel consumption and power requirements. The sensitivity analysis revealed a bump or discontinuity in the power vs speed profile, corresponding to the minimum plow speed at which the snow will cease to flow over the plow. Reducing the coefficient of friction reduces this minimum plowing speed. This could mean the difference between success and failure in plowing some tight, heavily laden ...
The aim of this work is to compile an inventory of the main characteristics (chemical, morphological, mineralogical and grain size parameters) of the bulk cargo materials and of the material emitted during different port operations for possible use as tracers of the fugitive PM emission sources. For all cases, the tracer characteristics determined for each bulk material were also identified in the corresponding PM material emitted. This inventory could assist the harbour authorities to identify the origin of high PM events recorded by air quality monitoring networks in harbour areas, and could also help modellers to predict the impact of harbour activities on ambient PM levels. The harbour of Tarragona (north-east Spain) was selected for this study given the high volume of solids in bulk handled. To this end, 12 handling operations of selected materials (clinker, phosphate, pyrite ash, Mn mineral, fine Si-Mn, coke (coal), bituminous coal, tapioca, soybean, alfalfa, ...
BackgroundPolicies on waste disposal in Europe are heterogeneous and rapidly changing, with potential health implications that are largely unknown. We conducted a health impact assessment of landfilling and incineration in three European countries: Italy, Slovakia and England.MethodsA total of 49 (Italy), 2 (Slovakia), and 11 (England) incinerators were operating in 2001 while for landfills the figures were 619, 121 and 232, respectively. The study population consisted of residents living within 3 km of an incinerator and 2 km of a landfill. Excess risk estimates from epidemiological studies were used, combined with air pollution dispersion modelling for particulate matter (PM10) and nitrogen dioxide (NO2). For incinerators, we estimated attributable cancer incidence and years of life lost (YoLL), while for landfills we estimated attributable cases of congenital anomalies and low birth weight infants.ResultsAbout 1,000,000, 16,000, and 1,200,000 subjects lived ...
In the Fourth Dutch National Environmental Outlook (NMP, abbreviated in Dutch) of the National Institute of Public Health and the Environment (VROM), published in July 1997, possible future developments in the traffic and transport sector in the Netherlands are described for the period 1995-2020 and also evaluates present Dutch policies. NMP-4 also offers possible solutions for expected environmental problems. This report serves as a background document for the traffic and transport sector. With a view to present Dutch policies, the main conclusions drawn from the Outlook are that: (1) the policy targets for car and lorry use for 2010 will not be met, (2) the target for CO2 emissions from road transport for 2010 will not be met, (3) the NOx emission target for 2010 will be met for cars, but not for trucks, (4) the VOC emission target for 2010 will be met for cars, but not for trucks, and (5) the noise targets for road transport or for civil ...
More than 30 environmental concerns were analyzed for the transportation of coal by rail, roads (trucks), high voltage transmission lines (that is, from mine-mouth generating plants to distribution networks), coal slurry pipelines, and barges. The following criteria were used to identify these problems: (1) real physical environmetal impacts for which control technologies must be developed, or regulation made effective where control technologies presently exist; (2) the level of impact is uncertain, although the potential impact may be moderate to high; (3) the concerns identified by the first two criteria are specific to or exacerbated by coal transportation. Generic transportation problems are not included. The significant environmental problems identified as a result of this study are: (1) rail transport - community traffic disruption and human health, safety, and habitat destruction; (2) coal haul roads - road degradation, traffic ...
In 1990, 176 million tonnes (mt) of air-traffic fuel was burned, which produced about 550 mt CO{sub 2}, 220 mt water, 3.5 mt NO{sub x} amd 0.18 mt SO{sub 2}. NO{sub x} emissions from air traffic may, by increasing ozone concentrations, be responsible for about 8% of global greenhouse warming. In the stratosphere NO{sub x} from aircraft is partly responsible for ozone depletion. With present technology 500 aircraft in the stratosphere would cause global ozone losses of 20%. Water vapour added by aircraft also contributes to global warming. In the form of ice crystals between 8 to 13 km above sea level, it acts as cirrus clouds. Probably the least damaging cruising altitude for aircraft is 9 km above sea level. Fuel consumption by aircraft is increasing. Air pollution abatement measures include substituting hydrogen fuel for kerosene, developing engines that emit less NO{sub x} and the introduction of internationally negotiated taxes on kerosene. ...
We present a new modular traffic signs recognition system, successfully applied to both American and European speed limit signs. Our sign detection step is based only on shape-detection (rectangles or circles). This enables it to work on grayscale images, contrary to most European competitors, which eases robustness to illumination conditions (notably night operation). Speed sign candidates are classified (or rejected) by segmenting potential digits inside them (which is rather original and has several advantages), and then applying a neural digit recognition. The global detection rate is ~90% for both (standard) U.S. and E.U. speed signs, with a misclassification rate 150 minutes of video. The system processes in real-time ~20 frames/s on a standard high-end laptop.
The emergence of nanoscience has increased the importance of experiments able to probe the very local structure of materials, especially for disordered and heterogeneous systems. This is technologically important; for example, the nanoscale structure of glassy polymers has a direct correlation with their macroscopic physical properties. We have discovered how a local, high frequency dynamic process can be used to monitor and even predict macroscopic behavior in glassy polymers. Polyvinylethylenes vitrified by different chemical and thermodynamic pathways exhibit different densities in the glassy state. We find that the rate and amplitude of a high frequency relaxation mode (the Johari-Goldstein process involving local motion of segments of the chain backbone) can either correlate or anti-correlate with the density. This implies that neither the unoccupied (free) volume nor the configurational entropy governs the local dynamics in any general ...
High-spin states in the mirror pair nuclei {sup 49}Cr and {sup 49}Mn and their cross-conjugate partners, the mirror pair {sup 47}V and {sup 47}Cr have been investigated using experimental {gamma}-ray spectroscopic techniques. The combination of high-efficiency EUROBALL cluster Germanium detectors and clean exit-channel gating afforded by a 31-element silicon ball used in conjunction with a 15-detector neutron wall allowed a revision and extension to the energy level schemes of all four nuclei up to J{sup {pi}}=31{sup -}/2. The difference in excitation energy between states of equivalent spin in the parent nucleus and its analogue partner have thus been established for both mirror pairs up to the f{sub 7/2}-shell band terminating state for the first time. This difference is assumed to be due almost entirely to the Coulomb effect and is therefore called the Coulomb energy difference (CED). The variation in the CED with spin has been interpreted as reflecting the change in the way the ...
A model system, described by the consistent Vlasov-Poisson equations under periodical boundary conditions, has been studied numerically near the point of a marginal stability. The power laws, typical for a system, undergoing a second-order phase transition, hold in a vicinity of the critical point: (i) A {proportional_to} -{theta}{sup {beta}}, {beta}=1.907{+-}0.006 for {theta} {<=} 0, where A is the saturated amplitude of the marginally-stable mode; (ii) {chi} {proportional_to} {theta}{sup -{gamma}} as {theta} {yields} 0, {gamma}={gamma}{sub -}=1.020{+-}0.008 for {theta} < 0, and {gamma}={gamma}{sub +}=0.995{+-}0.020 for {theta} > 0, where {chi}={partial_derivative}A/{partial_derivative}F{sub 1} at F{sub 1} {yields} 0 is the susceptibility to external drive of the strain F{sub 1}; (iii) at {theta}=0 the system responds to external drive as A {proportional_to} F{sub 1}{sup 1/{delta}}, and {delta}=1.544{+-}0.002. {theta}=(<v{sup ...
A tiered communications architecture for managing network traffic in a distributed system. Communication between client or control computers and a plurality of hardware devices is administered by agent and monitor devices whose activities are coordinated to reduce the number of open channels or sockets. The communications architecture also improves the transparency and scalability of the distributed system by reducing network mapping dependence. The architecture is desirably implemented in a proton beam therapy system to provide flexible security policies which improve patent safety and facilitate system maintenance and development.
Neuropilin 1 (Nrp1) is a coreceptor for vascular endothelial growth factor A165 (VEGF-A165, VEGF-A164 in mice) and semaphorin 3A (SEMA3A). Nevertheless, Nrp1 null embryos display vascular...Full Text Available
Within the EU-Project VOTALP (Vertical Ozone Transports in the Alps), we have shown that deep alpine valleys like the Mesolcina Valley very efficiently transport air out of the polluted valley up to altitudes between 2000 and near 4000 m asl (above sea level). Pollutants emitted in these valleys are very efficiently transported up to high altitudes. (author) 2 figs., 1 tab., 2 refs.
A 21-year-old male patient was transferred to the emergency room of our hospital after suffering seat belt abdominal injury in a traffic accident. Abdominal computed tomography revealed a massive hematoma...Full Text Available
The relativistic motion of an electron is numerically analyzed in a tokamak having macroscopic magnetic turbulence. Stochasticity induced by the relativistic motion overwhelms the phase averaging effect, which provides a tokamak with an effective loss mechanism for the avoidance/suppression of runaway electron generation at a major disruption. On the other hand, electrons in the KAM (Kolmogorov-Arnold-Moser) region will be observed as a runaway snake. (author)
Abstract A diacrylate polysulfone oligomer is synthesized and used as the acrylic oligomer for the in situ synthesis of noble metal/PSU nanocomposites through UV-induced simultaneous radical polymerization of acrylic functionalities and NP formation by reduction of their precursors. Thus, silver or gold NPs are formed in situ during polymer network formation. FESEM analysis of the morphology of the cured systems demonstrates that the nanoparticles of the noble metals are homogeneously distributed in the network without macroscopic agglomeration.
The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented.
This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic steam induced by ultrasonics is a major contribution to heat transfer augmentation. (author).
This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic stream induced by ultrasonics is a major contribution to heat transfer augmentation. (author).
Progress in four research areas on this project are summarized under the following topics: (1) Geminate charge pair recombination in hexane; (2) Fast current measurements resulting from excitation of charge transfer (CT) states; (3) Measurement of the dipole moment of excited states by DC conductivity; and (4) Charge separation at macroscopic interfaces between electron donor and acceptor solids. In a final section, personnel who have contributed to the project during the past budget period are described.
The results of the thermo-hydro-mechanical (THM) study of the FEBEX bentonite performed during FEBEX II are presented. The laboratory test program continued in part with the works carried out during FEBEX I, particularly in activities related to tests aimed to the calibration of the models, the acquisition of parameters by back-analysis and the improvement of the knowledge on the behaviour of expansive clays. But the program has also included tests on new areas: investigations about the influence of the microstructure changes in bentonite, of temperature and of the solute concentration on the behaviour of clay. Besides, several tests were proposed in order to understand the unexpected behaviour observed in the mock-up test, towards the end of year 2. Temperature effects on water retention curves in confined and unconfined conditions were determined, and swelling pressure, hydraulic conductivity and swelling and consolidation strains as a function of temperature ...
An analysis is given of the problems which can be solved by the use of electric-powered vehicles. A detailed comparison is made of the energy consumption and the air polluting emissions of electric and conventional vehicles, taking into account the energy consumption of the vehicles and the primary energy consumption of electric power generation and automotive fuels production. Also the air pollution, as a result of power generation and fuel production are considered. In chapter 1 an outline is given of the traffic and transportation sector in the Netherlands with special attention to data on the energy consumption and the air pollution of this sector. Based on these data the problems can be formulated for which the application of electric vehicles can be a solution. In chapter three a brief description is given of the technical specifications and characteristics of electric vehicles. Special attention is paid to the battery types. The energy and environmental ...
Efforts has been made to specify surface ozone production in photochemical reaction due to the high concentration of NO_x and photon rays. The secondary reactions has been considered via optical measurements using actinometry and pyranometry which was followed for photochemical reactions at high temperature and because of air pollutants due to the traffic load and because of the inversion in certain days. The concentration of surface ozone which was measured in Tehran city center was in the range of 24- 45 ppb in 1991-1992 and a higher concentration of 45-65 ppb was measured in 1999-2000. This high surface ozone concentration could cause a severe damage to biota, fauna and human health.
The measurement of air pollutants is no more sufficient. It is necessary to assess the risk induced by air pollution, and then to put in place actions to reduce it. The air quality monitoring takes into account different pollutants: nitrogen oxides, carbon monoxide, particulates for the traffic; sulfur dioxide and particulates for use of fuel or coal or chemical transformations in air; ozone and nitrogen dioxide from hydrocarbon and nitrogen oxides emissions; the use of simulation methods allow to calculate the concentrations levels for these pollutants taken as indicators. (N.C.)
ABB has developed an electric drive system featuring a high-energy, sodium-sulphur battery. The energy-to-weight ratio of this battery is four times that achieved with conventional lead-acid batteries. To recharge the battery, a charger mounted next to the motor has only to be connected to a household power socket. Road testing of electric cars is already under way, with production of commercially significant series planned for the early 1990s. The drive system will enable a typical family saloon to be driven at 120 km/h and allow a range of action of 200 km in urban traffic. (authors).
... (restricted)] 255-269 Inefficiency of Logit-Based Stochastic User Equilibrium in a Traffic Network Under ATIS by Hai-Jun Huang & Tian-Liang Liu & Xiaolei ...Hub-catchment Areas, Existing Hubs, and Simulation: A Case Study of Serbian Intermodal Terminals by Milorad Vidovic & Slobodan Zecevic & Milorad Kilibarda ... (restricted)] 389-410 Stochastic Location-assignment on an Interval with Sequential Arrivals by Kannan Viswanath & James Ward [Downloadable! (restricted)] ... (restricted)] 193-208 Solving Stochastic Transportation Network Protection Problems Using the Progressive Hedging-based Method by Yueyue Fan & Changzheng Liu [Downloadable! (...
Some recent achievements in the field of high pressure vessels and safety devices have offered a concrete chance to the application of compressed hydrogen for fleet commercial vehicles for urban use. Accordingly with this concept, ENEA has modified a Fiat Ducato van with a dual fuel engine, retaining the gasoline tank for long distance travelling and adopting the external mixture formation technique, with hydrogen injectors developed by ENEA, for non-polluting short-range duties in urban traffic. The article deals with the rationale for this choice and gives a general view of the project. (author)
The increasing sophistication of modern cars and todays tendency of developing compact vehicles more adapted to urban traffic have led to increased performance requirements from alternators and their bearings. This paper describes todays criteria for the design of alternators and of their bearings (improvement of tightness, design of race, grease, specific steels) and the final validation of the products. The last part of the paper describes the new CARB toroidal roller bearing developed by SKF which can support misalignments and internal axial displacements under high rotation speeds. (J.S.)
We consider a Bose-Einstein condensate (BEC) of N atoms of repulsive interaction #approx# U_0, in an elliptical trap, axially pierced by a Gaussian-intensity laser beam, forming an effective (quasi-2D) toroidal trap with minimum at radial distance #rho# = #rho#_p. The macroscopic angular momentum states #PSI#_l(#rho#,#theta#) #approx# #sq root#N#PHI#_l(#rho#)e"i"l"#theta# for integer l spread up to #rho# > #rho#_p. The spreading lowers rotational energies, so estimated low metastability barriers can support large l < or approx. l_m_a_x #approx# (NU_0)"1"/"4, < or approx. 10 for typical parameters. The l-dependent density profile module #PHI#_l(#rho#)"2 -#PHI#_0(#rho#)"2 is a signature of BEC rotation. Results are insensitive to off-axis laser displacements #rho#_0, for #rho#_0 #rho#_m_a_x << 1. (author).
A fractographic and numerical approach is presented to analyze hydrogen-plasticity interactions in pearlitic steel and to elucidate the main hydrogen transport mechanism in this material under triaxial stress states produced by notches. Fractographic analysis showed that the microdamage produced by the hydrogen was clearly detectable by scanning electron microscopy (SEM), through a specific microscopic topography associated with hydrogen effects (tearing topography surface or TTS). Numerical computations obtained by using an elastic-plastic finite element program gave the progressive spreading of the plastic zone, closely associated with the movement of dislocations. In the majority of cases, the plastic zone (PZ) clearly exceeds the hydrogen affected region (TTS) and has no relation with it. In some tests, however, the hydrogen-induced micro-damage surpasses the only region in which there is dislocation movement, and in this case the net macroscopic transport of ...
The method for calculating emissions to air has been revised, which has led to adjustments. Because of this, emissions in 1999 cannot yet be compared with previous years. Emissions in 1990 - 1998 are being recalculated now using the new method and are expected to be ready during 2001. Emissions to air of carbon dioxide (CO_2) in Sweden was 56.58 million tonnes in 1999, not including emissions from biofuels and international bunkers. The major sources of CO_2 emissions are the combustion of fossil fuels and the use of fuels for mobile sources. Total emissions to air of sulphur dioxide (SO_2) and nitrogen oxides (NO_x, counted as NO_2) in Sweden was 66 000 and 263 000 tonnes respectively in 1999. International bunkers are not included. The major source of SO_2 emissions is combustion of fossil fuels. Road traffic is the major source of NO_x emissions. Emissions to air of methane (CH_4), nitrous oxide (N_2O), carbon monoxide (CO) and volatile organic compounds (NMVOC) ...
Violation of correspondence principle may occur for very macroscopic byt isolated quantum systems on rather short timescales as illustrated by the case of Hyperion, the chaotically tumbling moon of Saturn, for which quantum and classical predictions are expected to diverge on a timescale of approximately 20 years. Motivated by Hyperion, we review salient features of ``quantum chaos`` and show that decoherence is the essential ingredient of the classical limit, as it enables one to solve the apparent paradox caused by the breakdown of the correspondence principle for classically chaotic systems.
We study quantum Darwinism -- the redundant recording of information about a decohering system by its environment -- in zero-temperature quantum Brownian motion. An initially nonlocal quantum state leaves a record whose redundancy increases rapidly with its spatial extent. Significant delocalization (e.g., a Schroedinger's Cat state) causes high redundancy: many observers can measure the system's position without perturbing it. This explains the objective (i.e. classical) existence of einselected, decoherence-resistant pointer states of macroscopic objects.
Periosteal Ewing's sarcoma is an uncommon, but well documented origin of this malignant condition with radiography signs, different from intramedullary growing tumours. Imaging modalities like CT or MRI supply proof of macroscopically intact endosteal cortical surface and free medullary cavity in long bones affected by this periosteal type of malignancy. Definite confirmation is valid after a careful microscopic investigation of the resected specimen. The prognosis of this type of Ewing's sarcoma may be favourable than that of the central type. Early diagnosis and therapy are thus essential. A clinical survey of six observations is given. (orig.).
This paper presents fundamental researches based on the electronic structure calculations and X absorption spectroscopy, allowing the knowledge on nuclear fuels at an atomic scale. They bring a better understanding of these material behavior to accurate the macroscopic simulation. The calculation methods, the experimental techniques of validation and the ab initio calculations results are detailed. (A.L.B.)
Nuclear forensics aims at identifying origin and intended use of nuclear material using information inherent to the nuclear material.The information gathered in nuclear forensics include isotopic composition, elemental composition, impurities and age of the material, macroscopic appearance and microstructure. The information so collected helps to solve criminal cases and put the individuals involved in nuclear trafficking in jails. The information also helps to improve safeguards and physical protection measures at place of theft or diversion to prevent future thefts or diversions.
Carbon nano tubes are easily produced in macroscopic quantities, however their characterisation and possible applications are still rather limited. We have developed a new method to make aligned nano tube films which open new opportunities, not only for basic research but also for eventual applications. With this method the tubes can be aligned either parallel or perpendicular to the surface. We give a short review of the microscopic properties of single tubes and the bulk properties of the aligned films. (author). 24 refs., 6 figs.
This work presents results of investigations on d.c. glow discharge nitriding of #alpha#+#beta# Ti-6Al-4V titanium alloy. The treatment was performed at 843 K in nitrogen-hydrogen atmosphere, pressure 300 Pa. Special attention was paid to nitriding mechanism and determination of the role of ion bombarding in nitriding process of titanium alloys. Produced as a result of d.c. plasma nitriding surface layers were subjected to macroscopic observations, microstructure studies, microhardness testing and X-ray analysis. (author)
The article has three sections. The first discusses the environmental problems the tanker traffic poses to the Norwegian coastal waters and shores. Various precautionary measures and requirements are briefly presented. The size of the present marine transportation and the future Russian marine petroleum activity in the Barents area are briefly mentioned. The second named, conflicting exploration drilling, presents the conflicting interests regarding exploratory drilling in the Barents Sea in Norway. The environmental problems are large and have lead to an on-going reevaluation. Some pollution abatement measures are mentioned. The regional economic development is briefly outlined. The third deals with the Norwegian governmental safety activities and presents a brief survey of the official safety activities in the petroleum sector in Norway and the international cooperation particularly with the Russian Federation. The emphasis is on the maritime security, the safety ...
Biopharmaceutical R&D complexes are major emission sources of volatile organic compounds (VOCs), which may pose potential health risks for staff on site and residents nearby. In this paper health risk assessments were performed for the VOCs in the ambient air of a typical biopharmaceutical R&D complex in China. Results showed halogenated and alkyl compounds were dominant components among 24 major VOCs from 9 selected sampling sites, inside or around the complex. The principal component analysis (PCA) indicated VOCs were generated predominantly from the biopharmaceutical research activities (factor 1 (F1), 71.6%) and traffic vehicles (factor 2 (F2), 15.4%), which were confirmed by contour maps of five selected VOCs (benzene, toluene, chlorobenzene, methylene chloride and n-hexane) simulated...
Introduction Postoperative alopecia is a relatively rare event, and therefore both patients and surgeons are puzzled once it develops even though it is said to improve spontaneously with time in most cases. We report a parieto-occipital pressure-induced alopecia firstly developed in a patient who had undergone repeated surgery for 10?years after a traffic accident. Case report A 29-year-old male underwent segmental osteotomy at the upper and lower frontal edentulous areas for distraction osteogenesis. Throughout the operation, he was in the supine position with the hair covered with a paper cap and the head on a plastic vinyl chloride-covered soft foam horseshoe-shaped urethane sponge placed on the horseshoe-shaped headrest. About 2?weeks after the surgery, two patches of parieto-occipital...
The tremendous growth of wireless technologies has introduced the potential of continuous service adaptation to the users' needs by giving them the ability to be able to select and access the proper network based on different criteria. Moreover, next generation wireless networks have been designed to provide support for multimedia services, with different traffic characteristics and different Quality of Service (QoS) guarantees. However, the expansion of Wireless Local Area Networks (WLANs) and Worldwide Interoperability for Microwave Access (WiMAX) networks poses new research era in the decision of the access network selection. In this paper, the existing access network selection schemes are classified into three categories: the network-centric, the user-centric and the collaborative sche...
IP Multicast is one of the most absolute method for large bandwidth Internet applications such as video conference, IPTV, E-Learning and Telemedicine etc., But due to security and management reason IP Multicast is not enabled in Internet backbone routers. To achieve these challenges, lot of Application Layer Multicast (ALM) has been proposed. All the existing protocols such as NICE, ZIGZAG and OMNI are trying to reduce average delay by forming a Multicast tree. But still that problem has not been addressed fully. We are proposing a new protocol called NetRawALM, which will address the average delay, Reliability between nodes, Scalability of conference, Heterogeneity and resilient data distribution for real time multimedia applications by constructing the Network based Resource aware Multicast tree algorithm. This is very dynamic and decentralised. The proposed architecture is a LAN aware; it is used to reduce Internet Traffic.
Current Intrusion Detection System (IDS) technology is not suited to be widely deployed inside a Supervisory, Control and Data Acquisition (SCADA) environment. Anomaly- and signature-based IDS technologies have developed methods to cover information technology-based networks activity and protocols effectively. However, these IDS technologies do not include the fine protocol granularity required to ensure network security inside an environment with weak protocols lacking authentication and encryption. By implementing a more specific and more intelligent packet inspection mechanism, tailored traffic flow analysis, and unique packet tampering detection, IDS technology developed specifically for SCADA environments can be deployed with confidence in detecting malicious activity.
Comparative indices are given for the efficiency of phase control of remote-controlled self-compensating high-voltage transmission lines, including a consideration of the power transfer effect between high-voltage line circuits. A description is given of certain circuit variations for performing the technical means of regulating phase shift, and their characteristics which make it possible to evaluate the effect of the phase regulators on the electrical transmission system are also given. An examination is made of problems concerned with the design of lines, relay protection, computation of transfer processes and dynamic stability as well as the computation of over-voltage when shutting off short circuits during amplified electromagnetic ties between line circuits.
The purpose of this work was to evaluate the quality of a rural area near Faenza (Italy) by using an active biomonitoring approach, i.e., by placing homogeneous individuals of the perennial shrub Rosa rugosa in different sites throughout the area. Further sites, within the city or its environs, were used for comparison. Soil and leaves of R. rugosa were analyzed for their heavy metal content. The total heavy metal pattern of leaves closely paralleled the pattern registered in soil, with the highest content (both in total and assimilable forms) at the site in the urban area, which is exposed to heavy traffic. Pollen quality (abortiveness and viability) was also tested as a potential indicator of pollution. Pollen abortiveness was strictly related to Pb levels in leaves, while viability was ...
A new method for kinetic experiments with neutrons is described. This method combines the conventional triple-axis neutron spectroscopy with relaxation-type experiments. Whereas the former method yields information about the microscopic dynamics of solids, the latter provides macroscopic relaxation times. The combination of both methods allows to determine the microscopic mechanism of relaxation processes. The time-resolved triple-axis spectroscopy is limited to reversible processes and to time scales from 10"-"3 to 10"4 s. Typical applications are the kinetics of phase transformations (structural and dynamical changes), kinetics of domain distributions, kinetics of (spinodal) decomposition, reversible solid state reactions, time-dependent occupation of phonon states or phonon lifetimes. (orig.).
Upcoming high-intensity laser systems will be able to probe the quantum-induced nonlinear regime of electrodynamics. So far unobserved QED phenomena such as the discovery of a nonlinear response of the quantum vacuum to macroscopic electromagnetic fields can become accessible. In addition, such laser systems provide for a flexible tool for investigating fundamental physics. Primary goals consist in verifying so far unobserved QED phenomena. Moreover, strong-field experiments can search for new light but weakly interacting degrees of freedom and are thus complementary to accelerator-driven experiments. I review recent developments in this field, focusing on photon experiments in strong electromagnetic fields. The interaction of particle-physics candidates with photons and external fields can be parameterized by low-energy effective actions and typically predict characteristic optical signatures. I perform first estimates of the accessible new-physics parameter space ...
The phase diagram of Gdsub(x)Ysub(1-x)Th_4B_4 between the paramagnetic, superconducting and ferromagnetic state is reported. Low temperature dc-magnetization measurements reveal that macroscopic electro-magnetic effects are of minor importance for the suppression of Hsub(2c), which shows a smooth bell-shaped behavior for x >= 0.15 with no indication of an anomaly near Tsub(c2). At low temperature in samples with x >= 0.20 a transition from type II to type I superconductivity seems to occur. The low temperature normal state susceptibility follows a Curie-Weiss law indicating reentrant behavior for x >= 0.10. (orig.).
A macroscopic realization of the strange virtual particles is presented. The classical Helmholtz and the quantum mechanical Schr\\"odinger equations are analogous differential equations. Their imaginary solutions are called evanescent modes in the case of elastic and electromagnetic fields. In the case of non-relativistic quantum mechanical fields they are called tunneling solutions. The imaginary solutions of this differential equation point to strange consequences: They are non local, they are not observable, and they described as virtual particles. During the last two decades QED calculations of the imaginary solutions have been experimentally confirmed for phonons, photons, and for electrons. The experimental proofs of the predictions of the non-relativistic quantum mechanics and of the Wigner phase time approach for the elastic, the electromagnetic and the Schr\\"odinger fields will be presented in this article. The results are zero tunneling time and an ...
High-energy synchrotron x-ray diffraction (XRD) has been used to quantify load transfer in bovine plexiform bone. By using both wide-angle and small-angle XRD, strains in the mineral as well as the collagen phase of bone were measured as a function of applied compressive stress. We suggest that a greater proportion of the load is borne by the more mineralized woven bone than the lamellar bone as the applied stress increases. With a further increase in stress, load is shed back to the lamellar regions until macroscopic failure occurs. The reported data fit well with reported mechanisms of microdamage accumulation in bovine plexiform bone.
Abstract Introduction: Laparoscopic subtotal adrenalectomy (LSA) has emerged as a treatment option in the management of certain adrenal pathologies. After LSA, a satisfactory blood supply to the adrenal remnant is vital to preserve steroid function. The aim of this study was to review the adrenal blood supply with relevance to LSA. Materials and Methods: The adrenal blood supply was examined in three ways: 1) a review of six previous cadaver studies looking at adrenal blood supply; 2) a review of our 164 consecutive laparoscopic adrenalectomies (LAs) (January 1999?January 2009); the details of the main adrenal veins and variants had been prospectively recorded; and 3) dissection of 4 cadaver specimens (macroscopic and histologic examination was performed). Results: The six cadaver studies ...
Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi{sub 2}-based materials, which are borderline ceramic-intermetallic compounds. MoSi{sub 2} single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi{sub 2} possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi{sub 2}-Si{sub 3}N{sub 4} composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi{sub 2}-based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing.
Shadow effect was used for investigating damage of uranium dioxide monocrystal. The dependence of shadow minimum parameters on fluence of "2"2Ne ions with 172 MeV energy was followed when detecting fission fragments. Ion dose responsible for sufficient microdamage of lattice structure, included into the classification of heavy ion damage effect on monocrystals was determined. The problem of radiation intensity effect on the character of occurred damages was studied. It was established that macroscopic sample failure, caused by generation of considerable mechanical stresses in monocrystal under beam effect could be observed along with microdamages of lattice structure at ion flux density >10"1"2 cm"-"2Xs"-"1.
Background Photopolymerizable poly(ethylene glycol) (PEG) hydrogels offer a platform to deliver cells in vivo and support three-dimensional cell culture but should be designed to degrade in sync with neotissue development and endure the physiologic environment. Questions/purposes We asked whether (1) incorporation of degradation into PEG hydrogels facilitates tissue development comprised of essential cartilage macromolecules; (2) with early loading before pericellular matrix formation, the duration of load affects matrix production; and (3) dynamic loading in general influences macroscopic tissue development. Methods Primary bovine chondrocytes were encapsulated in hydrogels (n?=?3 for each condition). The independent variables were hydrogel degradation (nondegrading PEG and degrading olig...
Contrast agent-enhanced CT scans in nine male patients with histologically proved benign lymphoepithelial lesions of the perotid gland were reviewed. All scans showed cystic-appearing masses with peripheral rim enhancement corresponding to the macroscopic appearance of the lesion. Five patients were seropositive for human immunodeficiency virus (HIV) infection or had infections seen in acquired immunodeficiency syndrome. Three patients were members of high-risk groups. Only one patient had symptoms of the SICCA syndrome. Once a rare cause of parotid gland enlargement, benign lymphoepithelial lesions have recently been seen with increasing frequency in patients with HIV infection. Although the CT appearance is not pathognomic, correlation results of aspiration cytology and with clinical history can lead to a preoperative diagnosis of a benign lymphoepithelial lesion.
Precipitation-hardened single crystals of a beta (bcc) Ti--40 at. percent V--1.0 at. percent Si alloy were deformed in compression at 77 and 298"0K. The dependence of the yield stress upon aging time at 843"0K for solution-treated crystals shows two maxima which are caused by silicide precipitates. The orientation dependence of the yield stress and of the active macroscopic slip plane were determined as a function of aging time. The solution-treated as well as aged crystals exhibit an asymmetry of both the yield stress and the plane of slip, the degree of asymmetry being larger at 77 than at 298"0K. The asymmetry of slip and yielding is not affected by the presence of precipitation hardening. Results indicate that the effect of the dislocation core structure on dislocation motion is independent of the presence of precipitates. (auth).
Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...
This paper examines the technological, socio-economic and environmental feasibility of a proposal to strengthen the Italian commercial coastal shipping system as an alternative to bolstering existing road transport facilities in order to meet the requirements of increased trade in the new European free market. This prospect is of special importance to Italy due to its long coastlines. The principal elements taken into account are: investment capital, labour and energy requirements. The study first examines the supply and demand dynamics of the European transport system. Here, attention is given to energy consumption. This examination is followed by a review of the European situation with regard to normatives governing navigation and customs duties. Road, rail and maritime transport costs are compared, and an assessment is made of the economic feasibility of an integrated-means system of transport involving the coordinated use of special containers, tractor-trailers and interchangeable ...
Research highlights: {yields} The use of resonant photoemission in its 'core-hole clock' expression for the study of the dynamical charge transfer across hybrid organic-inorganic interfaces and for the intermolecular charge transfer in the bulk of organic thin films is reviewed. {yields} The electronic coupling to the substrate and the efficiency of charge transport across hybrid interfaces is different for individual electronic subsystems of the molecular adsorbate. {yields} The intermolecular charge transfer in the bulk of discotic liquid crystals occurs on the order of a few femtoseconds and is faster than expected from the macroscopic charge transport characteristics of the material. -- Abstract: The focus of this brief review is the use of resonant photoemission in its 'core-hole clock' expression for the study of two important problems relevant for the field of organic electronics: the dynamical charge transfer across ...
Non-uniform radionuclide distribution in tumours will lead to a non-uniform absorbed dose. The aim of this study was to investigate how tumour control probability (TCP) depends on the radionuclide distribution in the tumour, both macroscopically and at the subcellular level. The absorbed dose in the cell nuclei of tumours was calculated for {sup 90}Y, {sup 177}Lu, {sup 103m}Rh and {sup 211}At. The radionuclides were uniformly distributed within the subcellular compartment and they were uniformly, normally or log-normally distributed among the cells in the tumour. When all cells contain the same amount of activity, the cumulated activities required for TCP = 0.99 (A-tilde{sub TCP=0.99}) were 1.5-2 and 2-3 times higher when the activity was distributed on the cell membrane compared to in the cell nucleus for {sup 103m}Rh and {sup 211}At, respectively. TCP for {sup 90}Y was not affected by different radionuclide distributions, whereas for {sup 177}Lu, it was slightly ...
The urban zone needs clean air to assure public health. To achieve this goal several filter samples were collected in different sites in Algiers city. Toxic elements such as: Na, Mg, Cl, Sc, Cr, Ti, V, Fe, Co, Cu, Zn, Se, Br, Ag, Sb, Ce, La, Hf, Ta and Hg have been measured in the filters using neutron activation analysis technique. Irradiation of filter samples and standards were carried out in Es-Salem reactor. The experimental procedure and the results are discussed. We noted during this work that the upper limit values for suspended dusts and the high concentrations for some toxic elements found are due to the weather conditions and intense road traffic around collecting sites. (authors)
To assess the effects of automobile exhaust on human health, we determined serum concentrations of total immunoglobulin E and hyaluronate in 185 schoolchildren who lived in a district that contained major roads. Serum immunoglobulin E levels were elevated in children who had asthma or wheezing, but levels did no t differ with respect to distance of their homes from the major roads. Serum hyaluronate levels were higher in children who lived less than 50 m from the roadside, compared with children who resided a greater distance from roads. The difference, however, was significant only in a subgroup of children in whom immunoglobulin E levels exceeded 250 IU/ml. Our results suggest that serum hyaluronate levels in children reflect the effects of traffic-related air pollution. Children with high immunoglobulin E levels appeared to be particularly susceptible to the effects of automobile exhaust. 34 refs., 2 figs., 3 tabs.
Sandia National Laboratories has recently developed two major field test capabilities for unattended ground sensor systems at the Department of energy`s Nevada Test Site (NTS). The first capability utilizes the NTS large area, varied terrain, and intrasite communications systems for testing sensors for detecting and tracking vehicular traffic. Sensor and ground truth data can be collected at either of two secure control centers. This system also includes an automated ground truth capability that consists of differential Global Positioning Satellite (GPS) receivers on test vehicles and live TV coverage of critical road sections. Finally there is a high-speed, secure computer network link between the control centers and the Air Force`s Theater Air Command and Control Simulation Facility in Albuquerque NM. The second capability is Bunker 2-300. It is a facility for evaluating advanced sensor systems for monitoring activities in underground cut-and-cover facilities. ...
Full text.Lead is a toxic heavy metal. Nevertheless, it has been mined and used for more than 800 years. Among the different contemporary sources of lead pollution, emissions from the combustion of leaded gasoline is of particular concern, as it can constitutes more than 90 percent of total lead emissions into the atmosphere in congested urban areas. Concentrations of lead in air and blood are strongly correlated with gasoline lead content and traffic volume. As a result of the increasing awareness about the dangers of lead to human health and the measures to manage urban air pollution, the use of leaded gasoline has been decreasing worldwide. In Lebanon, in the absence of policies to reduce the use of lead in gasoline or to favor the use of unleaded gasoline, leaded gasoline is the predominant grade. The objective of this research work is to analyze the current status of gasoline, and to assess the feasibility and prospect of such action. For this purpose, ...
As network bandwidth continues to grow and longer paths are used to exchange large scientific data between storage systems and GRID computation, it has become increasingly obvious that there is a need to deploy a packet drop avoidance mechanism into network transmission protocols. Current end-to-end congestion avoidance mechanisms used in Transmission Control Protocol (TCP) have worked well on low bandwidth delay product networks, but with newer high-bandwidth delay networks they have shown to be inefficient and prone to unstable. This is largely due to increased network bandwidth coupled with changes in internet traffic patterns. These changes come from a variety of new network applications that are being developed to take advantage of the increased network bandwidth. This paper will examine the end-to-end congestion avoidance mechanism and perform a step-by-step analysis of its theory. In addition we will propose an alternative approach developed as part of a new ...
We consider relay selection technique in a cooperative cellular network where user terminals act as mobile relays to help the communications between base station (BS) and mobile station (MS). A novel relay selection scheme, called Joint Uplink and Downlink Relay Selection (JUDRS), is proposed in this paper. Specifically, we generalize JUDRS in two key aspects: (i) relay is selected jointly for uplink and downlink, so that the relay selection overhead can be reduced, and (ii) we consider to minimize the weighted total energy consumption of MS, relay and BS by taking into account channel quality and traffic load condition of uplink and downlink. Information theoretic analysis of the diversity-multiplexing tradeoff demonstrates that the proposed scheme achieves full spatial diversity in the quantity of cooperating terminals in this network. And numerical results are provided to further confirm a significant energy efficiency gain of the proposed algorithm comparing to ...
This Current Year Work Plan presents a detailed description of the activities to be performed by the Joint Integration Office during FY87. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance, task monitoring, information gathering and task reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of program status reports for DOE. Program Analysis is performed by the JIO to ...
Deteriorating air quality in urban areas is leading bus manufacturers to look for cleaner drives of urban buses. Various new systems are now available, but it is difficult to compare them and verify their effects without having a driving cycle accurately representing contemporary average urban bus use. The idealized form (engine cycle, passenger car cycle or different kW/tonnes ratio and traffic conditions) of existing driving cycles disqualifies them for the purpose. For this reason, it was decided to attempt the development of a new driving cycle for urban buses. To this end, measurements were carried out on buses in service in four major Dutch towns. The resulting data were combined to produce a reference cycle comprising all data relating to urban bus use. Statistical methods were then used to compare a large number of 15-20 minute cycles with this reference cycle, until one was found that corresponded closely to the reference cycle. 5 figs., 1 tab., 6 refs.
The purpose of this work was to evaluate the quality of a rural area near Faenza (Italy) by using an active biomonitoring approach, i.e., by placing homogeneous individuals of the perennial shrub Rosa rugosa in different sites throughout the area. Further sites, within the city or its environs, were used for comparison. Soil and leaves of R. rugosa were analyzed for their heavy metal content. The total heavy metal pattern of leaves closely paralleled the pattern registered in soil, with the highest content (both in total and assimilable forms) at the site in the urban area, which is exposed to heavy traffic. Pollen quality (abortiveness and viability) was also tested as a potential indicator of pollution. Pollen abortiveness was strictly related to Pb levels in leaves, while viability was inversely related to leaf Cr content. Our results suggest that R. rugosa has the potential to be a good biomonitoring system. - Rosa rugosa leaves and pollen are - to different ...
The purpose of this work was to evaluate the quality of a rural area near Faenza (Italy) by using an active biomonitoring approach, i.e., by placing homogeneous individuals of the perennial shrub Rosa rugosa in different sites throughout the area. Further sites, within the city or its environs, were used for comparison. Soil and leaves of R. rugosa were analyzed for their heavy metal content. The total heavy metal pattern of leaves closely paralleled the pattern registered in soil, with the highest content (both in total and assimilable forms) at the site in the urban area, which is exposed to heavy traffic. Pollen quality (abortiveness and viability) was also tested as a potential indicator of pollution. Pollen abortiveness was strictly related to Pb levels in leaves, while viability was inversely related to leaf Cr content. Our results suggest that R. rugosa has the potential to be a good biomonitoring system. - Rosa rugosa leaves and pollen are - to different ...
Critics of higher fuel economy standards for vehicles have long argued that improving vehicle fuel economy will require reducing vehicle weight, and that would result in an increase in the number of fatalities from vehicle crashes. Several researchers have estimated that an across-the-board reduction of vehicle weight would reduce passenger safety (Evans 1991; Kahane 1997; U.S. GAO 1994). However, little research has been done on the relationship of vehicle size and fatality rates, independent of weight (see, however, Joksch, Massie, and Pichler 1998). In this report we review previous analyses of the relationship of vehicle weight and safety. We do this to study the opportunities to improve fuel economy in a more sophisticated way than across-the-board mass reduction. The aim is to explore improvements in traffic safety by making selected vehicle groups lighter, and retaining or enlarging selected vehicle dimensions. Unfortunately, the effects of size and mass ...
In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ({sup 241}Am, {sup 242}Am, {sup 242}Pu, {sup 237}Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW spallation target and the ...
In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ("2"4"1Am, "2"4"2Am, "2"4"2Pu, "2"3"7Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW spallation target and the incineration of ...
The electromagnetic properties that present hydrogen and other nucleus of agro-alimentary products, have allowed widely use of magnetic resonance (MR) to study the composition and internal structure of these biological materials in a micro and macroscopic scale, in a nondestructive way. In this paper the physical principles, basic equipment to measure the MR signals and the MR imaging of any biological sample, are explained. It is also shown a review of the main agro-alimentary applications, emphasizing in the use of this principle to examine the internal quality of fruits and vegetables. In these products, the MR has been used to detect and follow the evolution of different factors that determine the internal quality after harvesting, during storage and after post harvesting processes. The main studies that have been conducted with MR in harvested products are about physiological disorders that take place during storage and conservation of fruits in controlled and ...
Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong decrease of both textures, whereas Mg has always a much stronger texture than Al5052. ...
Silicon nitride-based ceramics behavior is strongly influenced by microstructural parameters, which, in turn are determined by chosen densification method. Highly covalent Si-N bond hind are the silicon nitride densification. Therefore, metal oxides are used in order to get high density. However, such oxides must be carefully selected, because they affect the general macroscopic properties of sintered bodies. In the present work, the viability of rare earth concentrate use to produce #beta#--Si_6_-_xAl_xO_xN_8_-_x and its effect on mechanical properties of the sintering ceramics are studied. Additive composition, heating rate, soaking time and sintering temperature were took as variables. Hardness, fracture toughness, Young's modulus and flexural strength were investigated. Lattice parameter compositional dependence and secondary phases crystallized after past-sintering heat treatment were also determined. The results show that rare earth concentrate works very ...
When a highly collimated beam of particles is aimed along the atomic rows of an aligned single crystal, the averaging effect of high speed motion results, to the lowest order of approximation, in crystal electric fields which are transverse to the atomic rows. The enormous magnitude of the crystal transverse electric fields is unsurpassed by any other known earth-bound macroscopic sources. For example, the field strengths along the <100> axis of tungsten at 77 K approach 9{center dot}10{sup 13}V/m. Thus quantum electrodynamic (QED) processes in strong fields which are thought to occur only in the extra-terrestrial environment can now be investigated in the laboratory. Here we review the results of measurements performed at the SPS facility in CERN using highly collimated beams of electrons, positrons and photons in the 20-200 GeV range, and germanium crystals cooled to 77 K with thicknesses ranging from 0.07 mm to 1.40 mm. The focus is on the simplest ...
This report of progress and future objectives timetable is based on an included schematic of goals and objectives and the project abstract which is included as Appendix 1. Five matters are summarized in the order of (1) novel methods of calcified bone confocal microscopy and reconstruction image analysis of decalcified beagle and human cortical bone serial sections, (2) macroscopic cross-correlation of beagle and human cortical and cancellous bone fractions with CT analysis, (3) guidance to the most radiobiologically important skeletal regions of interest with the just completed {sup 90}Sr bone tumor map from life time beagle studies, (4) deposition patterns of radioactive agents that participate in apatite crystal nucleation processes in bone and leave radiation-excited electrons trapped in bone mineral, and (5) the budget period timetable. The discovery that beta particles from {sup 166}Ho (T{sub {1/2}} =26 hr, {beta}{sub max} = 1.8 MeV) phosphonic acid bone ...
This introductory text treats thermodynamics as an incomplete description of quantum systems with many degrees of freedom. Its main goal is to show that the approach to equilibrium -with equilibrium characterized by maximum ignorance about the open system of interest- neither requires that many particles nor is the precise way of partitioning, relevant for the salient features of equilibrium and equilibration. Furthermore, the text depicts that it is indeed quantum effects that are at work in bringing about thermodynamic behavior of modest-sized open systems, thus making Von Neumann's concept of entropy appear much more widely useful than sometimes feared, far beyond truly macroscopic systems in equilibrium. This significantly revised and expanded second edition pays more attention to the growing number of applications, especially non-equilibrium phenomena and thermodynamic processes of the nano-domain. In addition, to improve readability and reduce unneeded ...
The plastic flow behavior of a #beta#-titanium alloy (Ti-15% Mo) was investigated over a wide range of temperatures and strain rates covering those conditions where the #omega#-phase forms dynamically. Portevin-Le Chatelier (PLC) effect was observed in this alloy at temperatures between 575 and 775 K at a strain rate of 1.31 x 10"-"4 s"-"1. The serrated flow behavior of this alloy could be suppressed by rendering the matrix #beta#-phase more stable against the #beta# to #omega# transformation. PLC bands formed in this alloy, studied at different levels of magnification using light, scanning electron and transmission electron microscopy, showed a high density of deformation bands within the macroscopic PLC band. The following mechanism of serrated flow is proposed; the load drop is ascribed to the sudden flow associated with the formation of deformation bands within which #omega#-particles were destroyed while the subsequent load rise results from pinning of ...
The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and polidal rotation in the high-beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10/sup 6/ cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal-plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10/sup 6/ cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collisional, Pfirsch-Schluter regime. The poloidal motion, however, results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the measured poloidal velocity. Mechanisms for the ...
The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and poloidal rotation in the high beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10/sup 6/ cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10/sup 6/ cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collosional, Pfirsch-Schluter regime. The poloidal motion, however results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the measured poloidal velocity. Mechanisms for the ...
Magnetic resonance imaging (MRI) has rapidly attained a major position among the examinations used in the diagnostic approach of multiple sclerosis because it is highly sensitive in demonstrating lesions. However, these lesional images may have several meanings, and there is the problem of distinguishing between oedema, which is said to reflect recent lesions, and gliosis which is thought to betray old lesions. The intrinsic MRI parameters studied (i.e. relaxation times) are unable to make this distinction, whereas it is provided by paramagnetic contrast media such as gadolinium. There is no correlation between the changes observed at MRI and the severity of the disease. Another problem is the accuracy of lesion localization, since visualization is predominantly macroscopic. This raises several questions about the demonstration of correlations between clinical signs and site of the lesion(s). At the moment, several teams of neuroradiologists are trying to find the ...
Calcium (Ca) plays an important role in regulating various cellular processes. In a variety of cell types, Ca signaling occurs within microdomains where channels deliver localized pulses of Ca which activate a nearby collection of Ca-sensitive receptors. The small number of channels involved ensures that the signaling process is stochastic. The aggregate response of several thousand of these microdomains yields a whole-cell response which dictates the cell behavior. Here, we study analytically the statistical properties of a population of these microdomains in response to a trigger signal. We apply these results to understand the relationship between Ca influx and Ca release in cardiac cells. In this context, we use a first passage time approach to show analytically how Ca release in the whole cell depends on the single channel kinetics of Ca channels and the properties of microdomains. Using these results, we explain the underlying mechanism for the graded relationship between Ca ...
There are few studies on coke's micro-pore structure in recent years, however, micro-pore structure of foundry coke determines its macroscopically quality index and reactivity in cupola furnace. Effect of such factors on micro-pore structure were investigated under different carbonization conditions with certain ratio of raw materials and material forming process in this article as charging temperature (A); braised furnace time (B); heating rate of the first stage (C)and the second stage (D) and holding time of ultimate temperature (E). Research showed that charging temperature was the most influential factor on the coke porosity, pore volume, pore size and specific surface area. It is suggested that formation of plastic mass and releasing rate of volatile during carbonization period are two main factors on microstructure of foundry coke while charging temperature contributes most to the above factors. 6 refs., 4 figs., 9 tabs.
Under severe operating conditions, such as starved lubrication, performance, service life, and reliability of rolling element bearings depend on the chemical and physical interactions between the contacting surfaces, the lubricant components, and the atmosphere. The IMKT{sup 1}, PI{sup 2}, and the imt{sup 3} have been cooperating on systematic investigations of interfacial interactions in high speed grease lubricated ball bearings. These include long time tests with complete bearings lubricated with greases of different composition under defined operating conditions, conducted at the IMKT, and chemical and physical characterizations of the running surfaces at the PI and imt. At the PI, in particular the chemical nature of the boundary layers has been investigated with time of flight secondary ion mass spectrometry (TOF-SIMS). The imt has been involved in the investigations by measuring the physical/mechanical properties of interacting surfaces at the micro/nano-scale after the removal ...
Pressureless-sintered AlN and hot-pressed, pressureless-sintered and reaction-bonded SiC were neutron irradiated at temperatures between 100 and 785degC up to a fluence of 5.2 x 10"2"4 n/m"2. The hardness was increased by up to 51% in AlN and 84% in SiC. The hardness decreased after annealing at temperatures around the irradiation temperature. At the same temperatures, the macroscopic length, which was increased by irradiation, also began to decrease. The hardness and length were almost recovered after 1,200 #approx# 1,400degC annealing. Thus, hardening in irradiated AlN and SiC is controlled by the number of point defects, or, more precisely, by the strain caused by small point defect clusters which pin down dislocation movement. Dislocation loops were still observed in some samples after 1,400degC annealing while the hardness was almost recovered to that in the unirradiated state. Thus, the existence of dislocation loops is not grounds for hardening in irradiated ...
In this paper, an investigation was performed on a failure pressure vessel, which was as an anti-freezing heater for General Gas Storage and Distribution (SGZ) system. Evident and serious deformation was observed on the body of the vessel. A metallurgical investigation was conducted to establish the mechanism and cause of deformation of the anti-freezing heater at Daya Bay PWR station in China. The investigation, which was performed on specimens cut from the most serious area deformed of the vessel, included macroscopic examination and microscopy examination. The results of the examinations showed that some lamellar pearlite in the microstructure were already spheroidized. It was confirmed that the vessel was operated at high temperature. Stress analysis for the vessel was conducted. And it was confirmed that, in ideal conditions, the vessel would be deformed at around 420 C. The overall results of the investigation showed that the failure of the protected ...
A press formability of magnesium alloy sheet cannot be evaluated by only general characteristics in tensile test; tensile strength, elongation n-value and r-value. For example, AZ31-alloy elongates about 20% in room temperature but breaks easily at shallow stage in deep drawing, which is caused by little local elongation (local necking). Crystallographic restriction of slip deformation in this alloy produces high strength, which almost equal to macroscopic fracture strength. In press forming, the bending under high tension requires a large deformability. A great difference in the deformability between AZ31 magnesium alloy and a strain hardened A1100 Aluminum (only 5% in elongation) is shown by static bending test with V-notch. In a rolled plate of AZ31, a crack is produced by stress concentration and propagates with reduced load at all testing temperature up to 453 K. In contrast, the point of notch in A1100 is dulled by local plastic deformation with held load in ...
Neutron radiography has been put to practical use in foreign countries as one of nondestructive inspection technologies, but in Japan, its application to other scientific fields is mainly researched. The reason is, the neutron radiography apparatuses installed in Japan are hard to be industrially utilized for a number of reasons, but also the characteristics of neutron radiography are not clearly established, and it is not standardized. The part from a collimator through an object to a detector is called ``upstream``, the part of an image detector is called ``midstream``, and the part of image processing is called ``downstream``. The nonparallel property of beam, image distortion and the lack of sharpness, beam quality and the interaction of neutron beam with an object are discussed about the upstream. The intensity of neutron beam, the energy spectra, the effective total macroscopic cross section, the effective energy, the evaluation of scattered beam and ...
Deformation mechanisms of Mg-Al-Zn (AZ31) alloys were investigated by performing tensile test at room temperature. In fine grain Mg alloys deformed at room temperature, nonbasal slip systems were found to be active as well as basal slip systems because of grain-boundary compatibility effect. Slip-induced grain-boundary sliding occurred as a complementary deformation mechanism to give rise to c-axis component of strain. With increasing grain size, the activation of the nonbasal slip systems was limited near grain boundaries. Instead of grain-boundary sliding, twinning occurred as a complementary deformation mechanism in large grained samples. Orientation analysis of twins indicated that twinning is induced by stress concentration due to the pile up of basal dislocations. The grain-size dependence on deformation mechanism was found to affect yielding behavior both microscopically and macroscopically which can influence various mechanical properties such as fatigue ...
From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and Zn content in the coating layer. 3. Zn-Fe (10-20%) alloy coating showed better durability against chlorine penetration than ...
A comprehensive attenuation data of dose equivalent for point isotropic monoenergetic neutron sources up to 400MeV in infinite shields of water, ordinary concrete and iron has been calculated using the ANISN-JR code and a neutron-photon multigroup macroscopic cross section HIL086R. The attenuation factors were fitted to a 4th order polynomial exponent formula, making possible to use easily for point kernel codes. Additional data in finite shielding geometry was also calculated to correct the effect due to infinite medium, giving the maximum correction of 0.23 in the region for more 400 cm distance from neutron source of 400 MeV in iron shield. Effective attenuation length for monoenergetic neutrons have been studied in detail. Subsequently, it was shown that the attenuation length was strongly dependent upon the penetration length and the Moyer`s formula using a single attenuation length brought large error into the dose estimation behind thick shields for the ...
The Cox proportional hazards model is the most widely used model for survival analysis because of its simplicity. The fundamental assumption in this model is the proportionality of the hazard function....Full Text Available
Institutional and organizational models ... Review individual centre institutional and organizational models in the light of the tasks to be performed by
We study a variant of the Penner-Distler-Vafa model, proposed as a c = 1 quantum gravity: quenched' matrix model with logarithmic potential. The model is exactly soluble, and exhibits a two-cut branching as observed in multicritical unitary matrix models and multicut Hermitian matrix models. Using analytic continuation of the power in the conventional polynomial potential, we also show that both the Penner-Distler-Vafa model and our quenched' matrix model satisfy Virasoro algebra constraints.
This update of a system concept entitled ``Maritime hazard prevention and water protection`` makes full use of the technical room for maneuver while considering that reasonable financial and economic conditions must be provided. The update allows on to continue or start the exploitation of feasible technical, logistic and information-technology development potentials. The same applies to the national maritime traffic safety measures developed for the German waterways. Considering the maritime hazards that have been prevailing in the coastal areas of the German North Sea, the conducted damage risk investigations suggest that a large-scale, disastrous oil contamination of the mud flats ecosystem cannot be excluded or controlled definitely in spite of the numerous measures taken. (orig.) [Deutsch] Mit der vorgelegten Fortschreibung zum Systemkonzept ``Gefahrenabwehr und Gewaesserschutz im Seeverkehr`` werden die technisch realisierten Handlungsspielraeume unter ...
The dominant shrubs were sagebrush and spiny hopsage; the herbs were dominated by cheatgrass and Sandberg bluegrass. Spiny hopsage appeared to be vulnerable to burning and also to damage by off-road vehicular traffic. It appears to have little or no ability to reproduce through seedlings; once the existing plants are killed they are not likely to be replaced, even if seed-producing plants are nearby. The only pure stand of spiny hopsage known to exist on the Hanford Site is on and near study plot 2H. Sagebrush, like spiny hopsage, is killed by burning and by heavy vehicles. Sagebrush is capable of reproducing via seeds, indicating that it is an inherently aggressive species with a capacity to reestablish itself if parent plants are in the vicinity to act as seed sources. Alien, annual plants, especially cheatgrass, were a major contributor to the herbaceous canopy cover in plots 3S, 4S, and 5S. However, native perennial grasses, especially Sandberg bluegrass, were ...
Samples of Parmelia sulcata and Xanthoria parietina from different biotopes have been analysed for elements of the series of uranium 238 and thorium 232. These species have been used as bio-monitors in different cases : urban areas, coal fired power plant, tip for uranium-mining residues. The concentration of most of these elements in lichens is decreasing as follows: radium waste-disposal site > area with uranium-rich soil > urban area > rural area. Road traffic was not found to increase notably the presence of radioactive lead in the environment. The two foliose lichens seem to have a comparable concentration ability, but Parmelia sulcata appeared to be more reliable. Some of the elements under investigation could be particularly problematic from a sanitary point of view: the intake limits in case of inhalation are very low and the atmospheric deposition is not negligible; this is particularly so for lead 210 and thorium 228. These elements should not ...
In recent years, several larger geothermal heat pump plants for offices or commercial areas have been designed and built in the central region of Germany, mainly in the Rhein-Main area. Systems with borehole heat exchangers (BHE; in the USA the term Vertical Loop is commonly used) as well as with shallow geothermal doublets (groundwater wells) are operational. New solutions had to be found to adapt the technology to certain site constraints, and innovative components such as thermally-enhanced grouting material have been used. This paper reviews the early development of Ground Source Heat Pumps (GSHP) for commercial buildings, gives details on a number of recent plants and discusses problems that arose during their realisation: UEG Wetzlar, a building with chemical laboratories and one of the first examples of direct cooling from BHE; DFS Langen (German Air Traffic Control Headquarters), with 154 BHE for heating and cooling, operating without antifreeze; Baseler ...
Work over the last few years at the Idaho National Engineering and Environmental Laboratory (INEEL) has included a major focus on applying human performance and human reliability knowledge and methods as an integral element of system design and development. This work has been pursued in programs in a wide variety of technical domains, beginning with nuclear power plant operations. Since the mid-1980`s the laboratory has transferred the methods and tools developed in the nuclear domain to military weapons systems and aircraft, offshore oil and shipping operations, and commercial aviation operations and aircraft design. Through these diverse applications the laboratory has developed an integrated approach and framework for application of human performance analysis, human reliability analysis (HRA), operational data analysis, and simulation studies of human performance to the design and development of complex systems. This approach was recently tested in the NASA Advanced Concepts Program ...
Data communication in a computer network environment is facing serious security threats from numerous sources such as viruses, worms, Zombies etc. These threats can be broadly characterized as internal or external security threats. Internal threats are mainly attributed to sneaker-nets, utility modems and unauthorized users, which can be minimized by skillful network administration, password management and optimum usage policy definition. The external threats need more serious attention as these attacks are mostly coming from public networks such as Internet. Frequency and complexity of such attacks is much higher as compared to internal attacks. This paper presents a host based network layer screening of external and internal IP packets for logging, analyzing and real-time detection of possible IP spoofing and Denial of Service attacks. This work can also be used in tuning security rules definition for gateway firewalls. Software has been developed which intercepts IP ...
The present paper explains the exhaust sources of and measures against CO2, and possibility of driving the electric cars which utilize the solar energy. In the combustion-related field, the thermal power generation attained to 24.6% which was the largest in exhaust quantity of CO2 on a division-by-division basis in FY 1990. On the consumers' side, four large consumption type industries which are steel, cement, paper, pulp and chemical industries totally occupy 64.2% of the exhaust quantity from all the industries. The emission from the cars occupies 17% of all the traffic-related exhaust quantity. The measures consist of decrease, fixation and absorption, among which the decrease is important. Newly developed electric cars comprise GM's Impact in spring, 1990, Nissan's FEN in 1991 and Tokyo Electric Power's IZA. The IZA is a 1800cc class direct drive system-driven sporty sedan which has been much improved for heightening the ...
In 1991, the air quality monitoring program in Alberta consisted of continuous, intermittent, static, portable, mobile, and acid precipitation monitoring networks. The air quality monitoring networks are described and results from the continuous, intermittent, static, and acid precipitation networks are summarized. Regulations and guidelines for individual pollutants are discussed in detail. Pollutants monitored continuously (1-h average basis) include ammonia, CO, coefficient of haze, H{sub 2}S, nitrogen oxides, ozone, SO{sub 2}, and total hydrocarbons. Good air quality was observed most of the time at all continuous monitoring stations in 1991. The frequency of good air quality ratings ranged from 81% at the Edmonton northwest station to 98% at the Fort McMurray station. Intermittent monitoring (every 6th day) was conducted for total suspended particulates and for vinyl chloride monomers in the Fort Saskatchewan area. Chemical analyses of benzo(a)pyrene and lead were performed on ...
For millions of people general noise and especially traffic noise are the main sources of environmental pollution. The increasingly stricter noise pollution abatement limiting values laid down by the law call for motor vehicle noise pollution abatement measures. Within the framework of today`s cost- and performance-oriented automobile and engine development developing engineers are required to reduce noise levels. The present state of the art is described and future possibilities of combustion engine structure-borne noise calculation and optimization are discussed from the point of view of K + P Computerunterstuetzte Strukturanalysen GmbH. (orig.) [Deutsch] Laerm allgemein und dabei speziell wiederum der Verkehrslaerm steht fuer Millionen von Menschen an allererster Stelle der persoenlichen Belastung durch die Umwelt. Zur Minderung der Laermbelastung werden vom Gesetzgeber immer schaerfere Grenzwerte vorgeschrieben, die dazu zwingen, Massnahmen zur ...
The security of ports and transportation is of utmost importance for the development of economy and the security of a nation. Among the necessary actions to ensure the security of ports and borders, the inspection of containers is one of the most time consuming and expensive procedures. Potential threats are the illegal traffic of radioactive materials that could be employed for the construction of weapons, as uranium and plutonium. New techniques for the inspections of containers should be fast, allow the detection and identification of dangerous materials, and be non-invasive, to reduce costs and delays. We propose to build a large surface photon and neutron detector based on plastic scintillator to identify the presence of fissile or fertile material inside a container. The detector consists of scintillator bars, wrapped in thin foils of reflecting material containing gadolinium for neutron capture and arranged in planes separated by few-millimeter-thick lead ...
The security of ports and transportation is of utmost importance for the development of economy and the security of a nation. Among the necessary actions to ensure the security of ports and borders, the inspection of containers is one of the most time consuming and expensive procedures. Potential threats are the illegal traffic of radioactive materials that could be employed for the construction of weapons, as uranium and plutonium. New techniques for the inspections of containers should be fast, allow the detection and identification of dangerous materials, and be non-invasive, to reduce costs and delays. We propose to build a large surface photon and neutron detector based on plastic scintillator to identify the presence of fissile or fertile material inside a container. The detector consists of scintillator bars, wrapped in thin foils of reflecting material containing gadolinium for neutron capture and arranged in planes separated by few-millimeter-thick lead ...
The role of natural enemies in the regulation of populations is one of the major questions facing population ecologists. Simplification have led to two theoretical ways of incorporating the role of natural enemies in single ecological models: diffusion models and patch-type models. The predictions of the models are different because of the way variability is incorporated. Three equations are presented for diffusion models and one for patch models. Since the two types of models apply at different combinations of spatial and temporal scales, the right model(s) to choose for a particular study requires careful assessment. A continuing dialogue between experimentalists and theoreticians will lead to a better understanding of natural systems such as those that occur in biological control.
The work in the past year has primarily involved four areas of magnetic thin films: amorphous rare earth-transition metal alloys, epitaxial CoPt{sub 3} and Ni-Pt alloy thin films, amorphous rare earth doped Si (a new class of dilute magnetic semiconductor with large negative magnetoresistance which the authors have discovered), and exchange-coupled antiferromagnetic insulators. In the amorphous alloys, they made a systematic study of the effects of local anisotropy, macroscopic (perpendicular) anisotropy, and exchange constant on the fundamental (and practical) properties of these magnetic alloys, as originally described in the grant proposal. The work on the epitaxial Co-Pt (and more recently Ni-Pt) alloys was originally undertaken as a comparison study to the amorphous alloys. Crystalline Co-Pt alloys have many striking similarities to the amorphous rare earth-transition metal alloys: perpendicular magnetic anisotropy, magneto-optic activity, and a {Tc} (for ...
Assessment of the immune system's capability to respond to antigens with the generation of specific antibodies, whilst under the influence of a test article, is required in toxicity tests according to the European guideline for repeated dose toxicity testing of medicinal products. The purpose of this study in rats was to validate methodology for the determination of Keyhole Limpet Haemocyanin (KLH)-specific antibodies under the influence of an immunologically active compound. The immunosuppressant FK506, commercially available as Prograf, was administered orally (gavage) to five rats per sex per group at dosages of 0.5mg/kg per day or 3mg/kg per day, for a period of 4 weeks. On days 14 and 22, KLH was administered subcutaneously, with an adjuvant (AluGel), to the two treated groups and a control (i.e. without FK506 treatment) approximately 1h following administration of FK506. Terminal investigations included haematology parameters, titration of KLH-specific antibodies in serum ...
The symmetrical complexes [{sup 99m}Tc][TcN(R{sub 2}PS{sub 2}){sub 2}] [R = CH{sub 3}, CH{sub 2}CH{sub 3}, CH{sub 2}CH{sub 2}CH{sub 3}, CH{sub 2}(CH{sub 3}){sub 2}], and the unsymmetrical complex [{sup 99m}Tc][TcN(Me{sub 2}PS{sub 2})(Et{sub 2}PS{sub 2})] have been prepared, at tracer level, through a two-step procedure involving the preliminary formation of a prereduced technetium nitrido intermediate followed by substitution reaction onto this species by the appropriate dithiophosphinate ligand [R{sub 2}PS{sub 2}]Na. The chemical identity of the resulting complexes have been established by comparison with the corresponding {sup 99}Tc-analogs prepared, at macroscopic level, by reacting the complex [{sup 99}TcNCl{sub 4}] [n-Bu{sub 4}N] (n-Bu = n-butyl) with an excess of ligand in methanol, and characterized by elemental analyses and spectroscopic techniques. The complexes are neutral and lipophilic, and possess a square pyramidal geometry, with an apical Tc N group ...
The symmetrical complexes ["9"9"mTc][TcN(R_2PS_2)_2] [R = CH_3, CH_2CH_3, CH_2CH_2CH_3, CH_2(CH_3)_2], and the unsymmetrical complex ["9"9"mTc][TcN(Me_2PS_2)(Et_2PS_2)] have been prepared, at tracer level, through a two-step procedure involving the preliminary formation of a prereduced technetium nitrido intermediate followed by substitution reaction onto this species by the appropriate dithiophosphinate ligand [R_2PS_2]Na. The chemical identity of the resulting complexes have been established by comparison with the corresponding "9"9Tc-analogs prepared, at macroscopic level, by reacting the complex ["9"9TcNCl_4] [n-Bu_4N] (n-Bu = n-butyl) with an excess of ligand in methanol, and characterized by elemental analyses and spectroscopic techniques. The complexes are neutral and lipophilic, and possess a square pyramidal geometry, with an apical Tc N group and two dithiophosphinate ligands spanning the four positions on the basal plane through the four sulfur atoms of ...
The synthesis, characterization of M"vO([CH_3CH_2N(CH_2CH_2S)_2](p-S-Ph-COOCH_2-CH_3)) (M:"9"9"mTc: I, Re: II) is presented in this work, where a pendant ester function is attached to the monothiolate ligand. Chemical structure of I is established after chromatographic comparison with II, synthesized in macroscopic amounts. Complex II is fully characterized by classical methods of analysis showing that the compound adopts a distorted trigonal bipyramidal configuration around the metal. The two sulfur atoms of the tridentate ligand and the oxo group form the basal plane, while the remaining nitrogen atom of the tridentate ligand and the sulfur atom of the monothiolate ligand occupy the apices of the bipyramid. In vitro challenge experiments with glutathione (GSH) in neutral aqueous medium demonstrate, that I suffers nucleophilic attack by GSH and thereby transformation to a more hydrophilic daughter metal compound. Formation of the latter depends on time and GSH ...
Radiation hardening in austenitic stainless steels is shown to modify deformation characteristics and correlate well with an increased susceptibility to intergranular stress corrosion cracking (IGSCC). Available data on neutron-irradiated materials have been analyzed and correlations developed between fluence, yield strength and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 to 2.5 x10"2"1 n/cm"2) for IGSCC are documented. In many cases, this variability is consistent with yield strength differences among irradiated materials. IGSCC correlates better to yield strength than to fluence for most heats suggesting a possible role of radiation-induced hardening and microstructure on cracking. Microstructural evolution during proton and heavy-ion irradiation has been characterized in low-carbon 304SSs. Hardening results from a dispersion of dislocation loops in the matrix which increase in density and size with ...
Background: Malformations of cortical development vary in neuronal maturity and level of functioning. Purpose: To characterize regional relative cerebral blood volume (rCBV) and difference in first moment transit time (TTfm) in polymicrogyria and cortical tubers using magnetic resonance (MR) perfusion imaging. Material and Methods: MR imaging and dynamic T2*-weighted MR perfusion imaging were performed in 13 patients with tuberous sclerosis complex, 10 with polymicrogyria, and 18 controls with developmental delay but no macroscopic brain abnormality. Regions of interest were placed in cortical tubers or polymicrogyric cortex and in the contralateral normal-appearing side in patients with malformations. In 'control' subjects, regions of interest were placed in the frontal and parietal lobes in both hemispheres. The rCBV and TTfm of the tuber/contralateral side (rCBVRTSC and TTFMTSC) as well as those of the polymicrogyria/contralateral side (rCBVRPMG and TTFMPMG) ...
Breakdowns occurring in rf accelerating structures will limit the ultimate performance of future linear colliders such as the Compact Linear Collider (CLIC). Because of the similarity of many aspects of dc and rf breakdown, a dc breakdown study is underway at CERN to better understand the vacuum breakdown mechanism in a simple setup. Measurements of the field enhancement factor ? show that the local breakdown field is constant and depends only on the electrode material. With copper electrodes, the local breakdown field is around 10.8GV/m, independent of the gap distance. The ? value characterizes the electrode surface state, and the next macroscopic breakdown field can be well predicted. In breakdown rate experiments, where a constant field is applied to the electrodes, clusters of consecutive breakdowns alternate with quiet periods. The occurrence and lengths of these clusters and quiet periods depend on the evolution of ?. The application of a high field can even ...
Nuclear material is either a product of technological processing of natural source material or it is entirely of anthropogenic origin. Consequently, nuclear material carries 'tool-marks' or 'fingerprints' of the process it was subjected to. Uranium fuels are examples of the first category, while plutonium belongs to the second category. The nature of these production processes is reflected in the elemental and isotopic composition of the material as well as in its microscopic and macroscopic appearance. All of these parameters can be determined using appropriate analytical techniques and they may result in important conclusions on the history and on the origin of the material. Therefore, they provide the most essential contribution to the prevention of future diversions of nuclear material from the same source. So far, essentially metallic impurities or light elements have been investigated for their potential in providing clues either on the type of process they ...
Objective: To assess dynamic MRI with Gd-DTPA enhancement for evaluating inflammatory changes in the subacromial bursa. Design and patients: We detected the signal intensity changes in dynamic MRI of the subacromial bursa, and confirmed these macroscopically by arthroscopy and histologically. The signal intensity was measured using built-in software, and the enhancement ratio (E ratio) was calculated from dynamic MR images. In addition, as a parameter of the rate of the increase in the signal intensity from 0 to 80 s, the mean increase per second in the E ratio was obtained as the coefficient of enhancement (CE). The correlation was studied of the E ratio and CE with the arthroscopic findings (redness, villous formation, thickening and adhesion), and of the E ratio and CE with the histological findings (capillary proliferation, papillary hyperplasia, fibrosis and inflammatory cell infiltration) of the subacromial bursa. Of patients with shoulder pain, this study ...
A 12 m.y. record of large rhyolitic eruptions from the Coromandel (CVZ) and Taupo (TVZ) volcanic zones of New Zealand is contained in cores retrieved by Leg 181 of the Ocean Drilling Program. Site 1124, located 670 km from the TVZ, has a maximum of 134 macroscopic tephra layers with a total thickness of 13.18 m. These units, along with between 7 and 63 tephras from 3 other sites, were dated by a combination of magnetostratigraphy, biostratigraphy, isothermal plateau fission track determinations, and geochemical correlation with onshore tephra deposits. Additional time control for the last 3 m.y. came from an orbitally tuned, benthic, oxygen isotope profile for Site 1123. Results extend the incomplete terrestrial record of volcanism by placing the first major rhyolitic eruption in the CVZ at c. 12 Ma, c. 1.6-1 m.y. earlier than previously known. Tephras became thicker and more frequent from the late Miocene into the Quaternary - a trend that probably reflected (1) ...
The environment - external or internal degrees of freedom coupled to the object of interest - can, in effect, monitor some of its observables. As a result, the eigenstates of these observables decohere and behave like classical states. Continuous destruction of superpositions leads to the effective environment-induced superselection (einselection), which is beginning to be recognized as a key step in the transition from quantum to classical. We investigate it here in the context of quantum chaos. I show that the evolution of a chaotic macroscopic system is not just difficult to predict (requiring accuracy exponentially increasing with time) but quickly ceases to be deterministic in principle as a result of the Heisenberg uncertainty (which limits the available resolution). This happens after a time t{sub {Dirac_h}} which is only logarithmic in the Planck constant. For example, various components of the solar system are chaotic, with the Lyapunov timescales ranging ...
Nuclear Forensics is a key element in the response process which is initiated after detection of illicit nuclear or other radioactive material. Credible nuclear forensics relies on appropriate sampling procedures, on validated analytical methods and on thorough data analysis and interpretation. Nuclear forensics aims at providing clues on the history and the potential origin of the material. Elemental and isotopic composition of the material, as well as its macroscopic and microscopic appearance reflect the technological processes used for the fabrication of the material. The nuclear forensic analysis first of all results in measurement data. Through appropriate processing of these data information on the nature and the history of the material can be obtained. A number of data evaluation techniques serving this purpose are conceivable and have been applied. On the one side, statistical methods like principal component analysis (PCA) or classification and regression ...
Studies are made in this program to enhance our understanding of the role of 5f electrons in chemical bonding. Most of our studies on the macroscopic scale emphasize certain isotopes available from the National Transplutonium Production Program centered at HFIR/TRU -namely, _9_6"2"4"8Cm, _9_7"2"4"9Bk, _9_8"2"4"9Cf, _9_9"2"5"3Es, and _9_9"2"5"4Es. Particular classes of compounds, such as hydrides, chalcogenides, and pnictides are often selected for study on the basis of their utility in bringing out significant chemical differences between the lanthanides and the actinides. High temperature/high pressure experiments on actinide metals and compounds reveal characteristics about the degree of 5f electron localization as a function of atomic number in the series. Magnetic properties of metals and compounds are investigated using ultra-sensitive methods and hydration numbers of ions in solution are investigated by neutron scattering at HFIR. As a result of a recently ...
Background and purpose: the recent RTOG guidelines for future clinical developments in gynecologic malignancies included the investigation of dose escalation in the paraaortic (PO) region which is, however, very difficult to target due to the presence of critical organs such as kidneys, liver, spinal cord, and digestive structures. The aim of this study was to investigate intensity-modulated radiotherapy's (IMRT) possibilities of either increasing, in a safe way, the dose to 50-60 Gy in case of macroscopic disease or decreasing the dose to organs at risk (OR) when treatment is given in an adjuvant setting. Material and methods: the dosimetric charts of 14 patients irradiated to the PO region at the department of radiation oncology, university hospital of Liege, Belgium, in 2000 were analyzed in order to compare six-field conformal external-beam radio-therapy (CEBR) and five-beam IMRT approaches. Both CEBR and IMRT investigations were planned to theoretically ...
In the present study Balb/c mice were exposed to 3,4-benzopyrene, painted on the skin every 2nd day for a total of 6 months, and simultaneously irradiated with athermal (5 mW/cm/sup 2/) or subthermal (15 mW/cm/sup 2/) doses of 2,450 MHz microwaves. The other group of animals was preirradiated with microwaves at 10 mW/cm/sup 2/ power level for 1, 2, or 3 months and then treated with benzopyrene, as above. Control mice were exposed for 6 months to benzopyrene, resulting in the development of baso- or spinocellular skin carcinoma within approximately 9 months, and sham-irradiated with microwaves. The growth of the tumour was assessed according to a self-designed 7-range macroscopic scale, supported by microscopical examinations of skin sections. All protocols of microwave irradiations resulted in a significant acceleration of the development of benzopyrene-induced skin cancer and in shortening of life span of the tumour-bearing hosts. This effect seemed to be ...
In the fields of medical imaging, geophysical well logging, and industrial radiography, it is often of interest to characterize the spatially distributed sensitivities of neutron and gamma-ray measurement devices to the physical properties of the materials being examined. For instance, one may wish to know how the count rate in a detector varies in response to small changes in the local density of the irradiated object as a function of position. Experimental determination of such sensitivity functions is often impractical. Consequently, we have developed a general three-dimensional Monte Carlo numerical technique that allows us to directly compute the differential sensitivity of an arbitrary integral response parameter, such as a time- or energy-discriminated count rate, with respect to the spatial distribution of macroscopic cross sections and sources in the irradiated medium. Sensitivities to object density, porosity, etc., can easily be derived from these ...
The antiviral drug combination consisting of arbidol and acetaminophen was investigated for its 4-week repeated oral administration in Sprague-Dawley rats. Groups of rats (10/sex in low-dose group, 15/sex in other three groups) were given at doses of 0, 200, 400, and 800 mg/kg/day. Clinical signs, mortality, body weight, food consumption, hematology, clinical biochemistry, macroscopic findings, organ weights, and histopathology were examined. The administration resulted in increased incidence of piloerection in most of the high-dose females and in some of the high-dose males and mid-dose females. Histopathological examinations revealed minor treatment-related change in the stomach of the high-dose animals. A decrease in body-weight gains and an increase in liver weight were observed in the mid- and high-dose groups. These treatment-related effects were reversible at the 2-week recovery period. A number of other clinical and pathological findings were not considered ...
A previously studied theory of gravitation in flat space-time is applied to homogeneous and isotropic cosmological models. There exist two different classes of models without singularities: (i) ever-expanding models, (ii) oscillating models. The first class contains models with hot big bang. For these models there exist at the beginning of the universe-in contrast to Einstein's theory-very high but finite densities of matter and radiation with a big bang of very short duration. After short time these models pass into the homogeneous and isotropic models of Einstein's theory with spatial curvature equal to zero and cosmological constant ALPHA >= O.
terms of 11) numerical models, 2D SPH simulations, and analytic models. The 1D model was useful for determining the evolution over very long timescales. ...
Models can be useful at many different levels when considering complex issues such as biological control of mosquitoes. At an early stage, exploratory models are valuable in exploring the characteristics...Full Text Available
A new supersymmetric gauge-invariant model is proposed. It is shown that the hidden-symmetry algebra for this model is the Kac-Moody algebra without a center.
Engine model: An engine and governor model adapted from a heavy lift helicopter simulation provides a restistic time delay between aerodynamic rotor ...
The Inner Model Hypothesis (IMH) and the Strong Inner Model Hypothesis (SIMH) were introduced by the first author in ``Internal consistency and the inner model hypothesis'', Bulletin of Symbolic Logic, December 2006. In this article we establish some upper and lower bounds for their consistency strength.
This 1978 annual report contains the results of ''Seismic testing of Wolsung-1 steam generator model'' which was initiated in 1977 as a part of a study on nuclear components testing. Model 78, improved version of Model 77 which did not take into account f...
Development of mouse models representing human spontaneous ovarian cancer has been hampered by the lack of understanding of the etiology of this very complex disease. Mouse models representing the different...Full Text Available
Cardiovascular modelling has been a major research subject for the last decades. Different cardiac models have been developed at a cellular level as well as at the whole organ level. Most of...Full Text Available
... trees, data showing a better fit to a power model than to a negative exponential model. Invading Pinus ... power law models were significantly negative. The inverse power model accounted for a considerabl...
In recent years the modelling of interannual climate variability has been studied, the atmospheric energy and water cycles, and climate simulations with the ECHAM3 model. In addition, the climate simulations of several models have been compared with special emphasis in the area of northern Europe
This paper presents research work concerning the mathematical modelling of air pollution in the Athens basin. A mathematical model based on aerodynamics and conservation equations together with turbulence modelling in body-fitted coordinates is used to provide the necessary input information to a similar but more detailed (i.e. small scale) model around Athens. Both models consist of solving the full Navier-Stokes equations and take into account the precise topography of the region. Different roughness heights are used for sea, coastal regions and land. The smaller scale model makes use of a two-equation turbulence model ({kappa}-{epsilon}) and the large scale model assumes a constant turbulence viscosity. The pollutant sources used in these models are based on actual emissions in the Athens area and ...
... a way to model a munition's terminal effects in a ... following attributes are handled in a stochastic fashion ... be improved by managing a queue of buffers ...
... They comprise of a power model for the representation of the electric system, a fluid model that represents the cooling fluid flow, three layers of ...
Non-linear autoregressive Markov regime-switching models are intuitive. Time-series approaches for the modelling of electricity spot prices are frequently proposed. In this paper, such models are compared with an ordinary linear autoregressive model with regard to their forecast performances. The study is carried out using German daily spot-prices from the European Energy Exchange in Leipzig. Four non-linear models are used for the forecast study. The results of the study suggest that Markov regime-switching models provide better forecasts than linear models. (author)
Non-linear autoregressive Markov regime-switching models are intuitive. Time-series approaches for the modelling of electricity spot prices are frequently proposed. In this paper, such models are compared with an ordinary linear autoregressive model with regard to their forecast performances. The study is carried out using German daily spot-prices from the European Energy Exchange in Leipzig. Four non-linear models are used for the forecast study. The results of the study suggest that Markov regime-switching models provide better forecasts than linear models. (author)
Decision-making is strongly based on modelling in two of our water supply projects concerning artificial ground water. The model used is a 2-dimensional flow and transport model using the element method. Due to sharp variations in Finnish soils, the modelling process is based on careful and detailed evaluation of basic hydrogeological data before and during model calibration.
The concept of frailty offers a convenient way to introduce unobserved heterogeneity and associations into models for survival data. In its simplest form, frailty is an unobserved random proportionality factor that modifies the hazard function of an individual or a group of related individuals. "Frailty Models in Survival Analysis" presents a comprehensive overview of the fundamental approaches in the area of frailty models. The book extensively explores how univariate frailty models can represent unobserved heterogeneity. It also emphasizes correlated frailty models as extensions of
Full text.Changes in land use and urbanization yield more pressure put on limited soil and water resources, including the risk of pollution with toxic heavy metals. The study area lies in the Bekaa valley totaling about 12753 ha. The valley receives from the west torrential fan deposits and a mixture of colluvial and alluvial material. The principal soil classes are Fluvisols, Cambisols, Regosols, Vertisols and Luvisols. The area is populated and also the most important agricultural part of the plain. Agriculture in the plain is being practiced mainly with cash, field crops and vegetables. The western surrounding area is being used mainly for terraced fruit trees. This Arab-German Technical Cooperation Project (ACSAD-BGR) aimed, following the ISO standards and Eikman-Klocke recommendations, at investigating the nature of the extends of soil pollution by heavy metals in two pilot areas: The central Bekaa-Lebanon and Ghouta-Damascus. Different institutions cooperate in the implementation ...
Background and purpose: the recent RTOG guidelines for future clinical developments in gynecologic malignancies included the investigation of dose escalation in the paraaortic (PO) region which is, however, very difficult to target due to the presence of critical organs such as kidneys, liver, spinal cord, and digestive structures. The aim of this study was to investigate intensity-modulated radiotherapy's (IMRT) possibilities of either increasing, in a safe way, the dose to 50-60 Gy in case of macroscopic disease or decreasing the dose to organs at risk (OR) when treatment is given in an adjuvant setting. Material and methods: the dosimetric charts of 14 patients irradiated to the PO region at the department of radiation oncology, university hospital of Liege, Belgium, in 2000 were analyzed in order to compare six-field conformal external-beam radio-therapy (CEBR) and five-beam IMRT approaches. Both CEBR and IMRT investigations were planned to ...
Using the operator approach we reexamine the two-dimensional model describing a massive Fermi field interacting via derivative couplings with two massless Bose fields, one scalar and the other pseudoscalar. Performing a canonical transformation on the Bose field algebra, the Fermi field operator is written in terms of the Mandelstam soliton operator and the derivative-coupling (DC) model is mapped into the massive Thirring model with two vector-current-scalar-derivative interactions (Schroer-Thirring model). The DC model with massless fermions can be mapped into the massless Rothe-Stamatescu model with a Thirring interaction (massless Rothe-Stamatescu-Thirring model). Within the present approach the weak equivalence between the fermionic sector of the DC model and the massive Thirring model is ...
This paper proposes the use of particle swarm optimization method (PSO) for finite element (FE) model updating. The PSO method is compared to the existing methods that use simulated annealing (SA) or genetic algorithms (GA) for FE model for model updating. The proposed method is tested on an unsymmetrical H-shaped structure. It is observed that the proposed method gives updated natural frequencies the most accurate and followed by those given by an updated model that was obtained using the GA and a full FE model. It is also observed that the proposed method gives updated mode shapes that are best correlated to the measured ones, followed by those given by an updated model that was obtained using the SA and a full FE model. Furthermore, it is observed that the PSO achieves this accuracy at a computational speed that is faster than that by the ...
A constitutive model for an explosive consists of three parts: equation of state of reactants, equation of state of products, and reaction rate. In the absence of a good physical theory, models are empirical and based on heuristics. For the HMX based plastic-bonded explosive PBX 9501, three models have previously been calibrated and used in numerical simulations. Here, these three models are compared. They illustrate several generic difficulties with developing and validating models. The available data is insufficient to determine a constitutive model uniquely. Different models can be calibrated to fit the available data yet differ significantly in regions of phase space of importance to applications. Comparing models gives an indication of the uncertainty in model predictions outside the ...
A detailed component-based simulation model of a geothermal heat pump system has been calibrated to monitored data taken from a family housing unit located at Fort Polk, Louisiana. The simulation model represents the housing unit, geothermal heat pump, ground heat exchanger, thermostat, blower, and ground-loop pump. Each of these component models was tuned to better match the measured data from the site. These tuned models were then interconnected to form the system model. The system model was then exercised in order to demonstrate its capabilities.
A detailed component-based simulation model of a geothermal heat pump system has been calibrated to monitored data taken from a family housing unit located at Fort Polk, Louisiana. The simulation model represents the housing unit, geothermal heat pump, ground heat exchanger, thermostat, blower, and ground-loop pump. Each of these component models was 'tuned' to better match the measured data from the site. These tuned models were then interconnect to form the system model. The system model was then exercised in order to demonatrate its capabilities.
This paper introduces a new way of estimating parameters in a Brownian motion regime switching asset model to incorporate volatility clustering. The regime switching model is then applied to pricing of up-and-in barrier call options. We take the probability of crossing the barrier between simulation points into account, and we increase accuracy in simulations by importance sampling. The regime switching model is compared to the Normal Inverse Gaussian model and the traditional Black-Scholes model, and option prices from the regime switching model are compared to the closed form expression of up-and-in barrier calls in a Black-Scholes market.
The National Energy Modeling System (NEMS) developed by the U.S. Department of Energy`s Energy Information Administration is a well-recognized model that is used to project the potential impact of new electric generation technologies. The NEMS model does not presently have the capability to model energy storage on the national grid. The scope of this study was to assess the feasibility of, and make recommendations for, the modeling of battery energy storage systems in the Electricity Market of the NEMS. Incorporating storage within the NEMS will allow the national benefits of storage technologies to be evaluated.
An integrated approach to the modelling of hydrogen assisted failure in 316L steel is presented. The approach includes experimental, fractographic, numerical and theoretical analysis of the phenomenon. The physical adequacy of the mechanical models of hydrogen embrittlement (notch extension model and notch cracking model) is discussed by comparing the virtual damage depth (theoretical) predicted by the models with the embrittled zone (microphysical) measured in the fractographic analysis by scanning electron microscopy. In addition, a numerical modelling of hydrogen diffusion is performed, concluding that bulk diffusion is not important in hydrogen embrittlement of 316L steel, so that hydrogen transport accelerated by the microdamage itself should be taken into account. (orig.)
The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the ...
The SMART (System-integrated Modular Advanced ReacTor) which is a 330 MWt advanced integral PWR was developed by the KAERI (Korea Atomic Energy Institute) for electricity generation and seawater desalination. A thermal hydraulic evaluation and analysis of the SMART is performed by the TASS /SMR-S (Transient And Setpoint Simulation/System integrated Modular Reactor-Safety). The TASS/SMR-S code has various models reflecting the design features of the SMART such as the drift flux model, the core models (core power and core heat transfer model), the component models, and the specific models. One of the core models is the core heat transfer model. The role of this model is to calculate the heat flux and radial temperature profiles at a fuel rod surface using the relevant heat transfer correlations for all ...
The objective of this Task Group is the coordination of research studies on biokinetic models and the evaluation of the implications of new biokinetic models on dose assessment and safety standards. For this the new ICRP models, which will be used for a revision of ICRP Publications 30, 54, 68 and 78, are implemented into six different computer codes in five European countries and quality assured by intercomparison procedures. The work has started with the implementation of the new ICRP Alimentary Tract Model. New systemic models and the new NCRP wound model will follow. The work also includes the evaluation of experimental results in terms of formulation by the new model structures and a quality assurance of model formulation. PMID:17556343
A class of nonlinear models combining a pharmacokinetic compartmental model and a pharmacodynamic Emax model is introduced. The locally D-optimal (LD) design for a four-parameter composed model is found to be a saturated four-point uniform LD design with the two boundary points of the design space in the LD design support. For a five-parameter composed model, a sufficient condition for the LD design to require the minimum number of sampling time points is derived. Robust LD designs are also investigated for both models. It is found that an LD design with $k$ parameters is equivalent to an LD design with $k-1$ parameters if the linear parameter in the two composed models is a nuisance parameter. Assorted examples of LD designs are presented.
The heat capacity and heat of fusion were measured for a number of minerals using differential scanning calorimetry (DSC). The DSC measurements showed that the heat of fusion for the minerals is very low compared to the heat of fusion for pure crystalline phases reported elsewhere. A model for the melting behaviour of mineral materials in terms of melting interval, heat capacities and heat of fusion has been developed. The only model input is the chemical composition of the mineral material. The model was developed to be implemented in a detailed model of a cupola furnace, thus the focus for the development was not only precision but also to obtain a model that was continuous and differentiable. The model is based on several different submodels that each covers a part of the heating and melting of rocks. Each submodel is based on large amounts of empirical data. ...
Stylized numerical models of the tooth are usually employed in qualification procedure related to Electronic Paramagnetic Resonance in long-term accidental contamination dose reconstruction. In this work a voxel model was developed from the microCT image data set of a human non contaminated molar tooth. A stylized model, reproducing the characteristics of the voxel model, was also created in order to investigate the level of accuracy that can be obtained in this kind of study.
The high-power model of Disk-and Washer (DAW) cavity for electron acceleration is under fabrication. Basic Dimensions of the cavity were determined from aluminum model measurement and electromagnetic field calculation. We have fabricated model made of OFC (Oxygen Free Copper) five times in total. Some details are optimized and corrected, and then the final brazing are proceeding. These model results and present status are described. (author)
This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed.
This report to the Nuclear Regulatory Commission (NRC) describes the development and application of a methodology to systematically and quantitatively assess predictive uncertainty in groundwater flow and transport modeling that considers the combined impact of hydrogeologic uncertainties associated with the conceptual-mathematical basis of a model, model parameters, and the scenario to which the model is applied. The methodology is based on a n extension of a Maximum Likelihood implementation of Bayesian Model Averaging. Model uncertainty is represented by postulating a discrete set of alternative conceptual models for a site with associated prior model probabilities that reflect a belief about the relative plausibility of each model based on its apparent consistency with available knowledge and ...
In this paper we present a modeling framework for analyzing computer models with two types of variations. The paper is based on a case study of an orthopedic surgical unit, which has both controllable and uncontrollable factors. Our results show that this structure of variation can be modeled effectively with linear mixed effects models and generalized additive models. Copyright (C) 2009 John Wiley & Sons, Ltd.
This paper presents a case study in the design and implementation of a numerical weather prediction model on a supercomputer (CRAY-1). Following a historical introduction to the evolution of the model, the governing equations of the model are presented and the numerical solution of these forecast equations is described. A brief tutorial on the architecture of the CRAY-1 is presented with a discussion of how it affects the choice of algorithms and code design of the model. A summary of the advantages gained by use of the vector aspects of the CRAY-1 is included.
...and welcome to ...lab also known as berkeley lab my name is jeff miller and ...and a public affairs i'd like to ? ...but space is science center and ...berkeley albany high school science department and berkeley high school science department and oakland high school science ...be a q. and ...here please use and because we wanna make sure that your questions are here ...heard of also for the latest developments on science and technology ...guy we're going to be any more and more new features i hope ...and change ...thank you ? much and thank you for coming on the welcome to my world of and mayotte science journalist and what i've done for the last almost thirty years ...people about things about which there passionate and national religion tonight and ...people to explain the science and and i asking the question so what ...and ...worldwide and what it does best ? uh ...bench science and turn it into reality what do you scientists and ...uh they take scientific theory and they turn ...
Tree-level scattering amplitudes of longitudinally polarized electroweak vector bosons in the Standard Model are calculated using Mathematica package Feyncalc. The modifications of low-energy theorems for longitudinally polarized W and Z in the Standard Model are discussed.
The brain maintains internal models of its environment to interpret sensory inputs and prepare actions. While behavioral studies demonstrated that these internal models are optimally adapted...Full Text Available
We obtain a symmetry algebra for any unitary minimal model by using the representation of conformal field theories. This symmetry algebra can be interpreted as a quantum group. The generalization to non-unitary minimal models is direct. (orig.).
We obtain a symmetry algebra for any unitary minimal model by using the representation of conformal field theories. This symmetry algebra can be interpreted as a quantum group. The generalization to non-unitary minimal models is direct. (orig.).
BackgroundLiquid chromatography-mass spectrometry (LC-MS) is one of the major techniques for the quantification of metabolites in complex biological samples. Peak modeling is one...Full Text Available
SummaryWe develop a new class of models, dynamic conditionally linear mixed models, for longitudinal data by decomposing the within-subject covariance matrix using a special Cholesky...Full Text Available
In this paper two different models of brain regulation of exercise performance are critically compared: the central governor model proposed by Noakes and colleagues, and an alternative psycholobiological model based on motivational intensity theory. PMID:18618133
The report provides and overview of calculation models for the simulation of airflows and deals comprehensively with field and multi-zone models as well as the coupling of individual zone and multi-zone models. Examples of calculations are given. figs., tabs., refs.
We show the existence of a rather general class of closed cosmological models of Bianchi type IX that do not exhibit recollapse but expand for all times. This is despite the fact that these models satisfy the strong energy condition by a wide margin.
A new 3D model is developed to simulate the self-oscillation of the elongated vocal folds. This model allows for large deformation and longitudinal displacement. The displacement boundary condition...Full Text Available
We present the formulation and testing of a mathematical model for the kinetics of homotypic cellular aggregation. The model considers cellular aggregation under no-flow conditions as a two-step process....Full Text Available
New habitat-based models for spread of hantavirus are developed which account for interspecies interaction. Existing habitat-based models do not consider interspecies pathogen transmission,...Full Text Available
Volume VII of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the tritium transport model documentation. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Volume VI of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the groundwater flow model data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Geochemical model is a kind of concept model which describes geochemical processes by means of chemical reaction equations and mathematical formula, and the software based on the concept model are called geochemical modeling code. Geochemical modeling codes can be divided into three categories: mass equilibrium, mass transfer and mass transport code. The major functions of geochemical codes include the calculation of forms of occurrence of elements, the prediction of direction of various geochemical reaction, the dissolution and precipitation of elements, the pH and Eh value, the rate and path of geochemical reaction in aqueous solution.
We discuss the asymptotic dynamical evolution of spatially homogeneous brane-world cosmological models close to the initial singularity. We find that generically the cosmological singularity is isotropic in Bianchi type IX brane-world models and consequently these models do not exhibit Mixmaster or chaotic-like behaviour close to the initial singularity. We argue that this is typical of more general cosmological models in the brane-world scenario. In particular, we show that an isotropic singularity is a past-attractor in all orthogonal Bianchi models and is a local past-attractor in a class of inhomogeneous brane-world models. (letter to the editor)
In this letter, they present the results on a global fit to precision electroweak data in a Higgs triplet model. In models with a triplet Higgs boson, a consistent renormalization scheme differs from that of the Standard Model and the global fit shows that a light Higgs boson with mass of 100-200 GeV is preferred. Triplet Higgs bosons arise in many extensions of the Standard Model, including the left-right model and the Little Higgs models. The result demonstrates the importance of the scalar loops when there is a large mass splitting between the heavy scalars. It also indicates the significance of the global fit.
In this paper extended models for estimating price developments on electricity markets are presented. The models consider deviations from the normality hypothesis of the prices. Based on an ARMA model combination with GARCH, Gaussian-mixture and switching-regime approaches are comparatively discussed. The comparison is based on historic electricity prices of the spot and two reserve markets in Germany. It is shown that the proposed extended models lead to significantly improved representations of the considered stochastic price processes. It is inferred that these models may be preferred for estimating price developments on electricity markets. (author)
pletely new PW fuel cell model had to be developed for CINDA. Several ...... following linear equation, which is used in the SINDA fuel cell model: ...
A review is made of some recent developments in the application of the Bohr Hamiltonian to transitional nulcei. The primary concern is to understand the advantages and limitations inherent to the basic model and its many variants. (author).
Abstract We present a study of the impact of different model groups in the detection of circumstellar debris discs. Almost all previous studies in this field have used kurucz (atlas9) model spectra to predict the stellar contribution to the flux at the wavelength of observation, thus determining the existence of a disc excess. Only recently have other model groups or families like marcs and nextgen (phoenix) become available to the same extent as atlas9. This study aims to determine whether the predicted stellar flux of a disc target can change with the choice of model family can a disc excess be present in the use of one model family whilst being absent from another. A simple comparison of kurucz model spectra with marcs and nextgen model spectra of identical stellar parameters was conduc...
We argue that the tachyons which exist in some string models are a signal of deconfinement. We compare the deconfinement temperature obtained from Monte Carlo calculations with some string models. (orig.).
We argue that the tachyons which exist in some string models are a signal of deconfinement. We compare the deconfinement temperature obtained from Monte Carlo calculations with some string models. (orig.).
... kinematic model for the robots and designed ... theoretic approach for modeling mobile robot teamn formations". ... "UUV teams, control from a biological ...
A strong necessary condition is given for the principal stabiliser of the action of a compact Lie group to have a non-zero centre. An application to the monopole problem in Yang-Mills-Higgs models is discussed.
BackgroundPreclinical models of pediatric cancers are essential for testing new chemotherapeutic combinations for clinical trials. The most widely used ...Full Text Available
... Those functions are fundamental routines to build a power model for more complex circuits or functional blocks. ... 21 of 54 6. Memory Power Model ...
The basic relationships of the convolution/superposition dose calculation technique are reviewed, and a modelling technique that can be used for obtaining a satisfactory beam model for a commercially available convolution/superposition-based treatment planning system is described. A fluence energy spectrum for a Co-60 treatment machine obtained from a Monte Carlo simulation was used for modelling the fluence spectrum for a Rokus M machine. In order to achieve this model we measured the depth dose distribution and the dose profiles with a Wellhofer dosimetry system. The primary fluence was iteratively modelled by comparing the computed depth dose curves and beam profiles with the depth dose curves and crossbeam profiles measured in a water phantom. The objective of beam modelling is to build a model of the primary fluence that the patient is ...
This dissertation is devoted to the study of the phenomenological consequences of the three-generation heterotic string models based on the Calabi-Yau compactifications and the N = 2 superconformal constructions.
In this paper, we suggest that perception could be modeled by assuming that sensory input is generated by a hierarchy of attractors in a dynamic system. We describe a mathematical model which exploits...Full Text Available
Sep 1, 2011 ... 2005. Computer simulation modeling of recreation use: current status, case studies, and future directions. Gen. Tech. Rep. RMRS-GTR-143. ...
Hemez9 on the Predictive Capability Maturity Model, and for their feedback on the CAS d uring a 2 007 technical interchange meeting in Albuquerque, NM. ...
A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a 137Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data...
AIMSTo develop a population pharmacokinetic–pharmacodynamic model to describe the occurrence and severity of bleeding or bruising as a function of enoxaparin exposure.METHODSData...Full Text Available
The aim of this work is the development and experimental validation of a detailed dynamic fuel cell model using the gPROMS modeling environment. The model is oriented towards optimization and control and it relies on material and energy balances as well as electrochemical equations including semi-empirical equations. For the experimental validation of the model a fully automated and integrated hydrogen fuel cell testing unit was used. The predictive power of the model has been compared with the data obtained during load change experiments. A sensitivity analysis has been employed to reveal the most critical empirical model parameters that should be estimated using a systematic estimation procedure. Model predictions are in good agreement with experimental data under a wide range of operati...
The present volume on modeling of batteries and fuel cells discusses the significance of the effectiveness factor for flooded porous electrodes, active pore distribution spectroscopy for characterizing porous battery electrodes, the agglomerate model for porous electrodes, and dynamic-performance measurements of battery cells for electric vehicles and other applications. Attention is given to mathematical modeling of a primary zinc/air battery, mathematical modeling of Grace Li-TiS2 cells, modeling of electrocrystallization processes in battery systems, and rotating disk electrode studies in molten Li/K carbonate eutectic. Topics addressed include the variability of nickel oxide cathode dissolution in molten carbonate fuel cells, water transport properties of fuel cell ionomers, modeling water content effects in polymer electrolyte fuel cells, and computer ...
The Model for the Assessment of Psychosocial Problems (MAPP) can help family medicine residents effectively assess patients with psychosocial problems. Following a patient-centred clinical method, MAPP...Full Text Available
Mice are an ideal mammalian model for studying the genetics of aging: considerable resources are available, the generation time is short, and the environment can be easily controlled, an important...Full Text Available
In undirected graphical models, learning the graph structure and learning the functions that relate the predictive variables (features) to the responses given the structure are two topics that have been widely investigated in machine learning and statistics. Learning graphical models in two stages will have problems because graph structure may change after considering the features. The main contribution of this paper is the proposed method that learns the graph structure and functions on the graph at the same time. General graphical models with binary outcomes conditioned on predictive variables are proved to be equivalent to multivariate Bernoulli model. The reparameterization of the potential functions in graphical model by conditional log odds ratios in multivariate Bernoulli model offers advantage in the representation of the conditional independence ...
An acute exudative Escherichia coli pyelonephritis rat model was used to study the influence of progressive pyelonephritis on the efficacy of antibiotic treatment. In this model, transient ureteral...Full Text Available
A generalised RIC model for the rotational - vibrational spectra of deformed even-even nuclei of ellipsoidal shape in the rare-earth region has been proposed by incorporating many important features of various microscopic models proposed earlier. The two mass-point model and the governor model moments of intertia are obtained on the basis of the proposed model with appropriate limiting values of the radius of the RIC. Also, the model moment of intertia goes to zero for spherical nuclei, thus giving no rotational spectra for such nuclei. A quantum mechanical treatment of the model on the basis of the two mass-point concept, is expected to give results which are in better agreement with experiments. (author).
note that this form for heat transfer augmentation has apparently never been used with other evaporation models, even though it is a natural extension of ...
In this report we focus on some aspects related to modeling and formal verification of embedded systems. Many models have been proposed to represent embedded systems . These models encompass a broad range of styles, characteristics, and application domains and include the extensions of finite state machines, data flow graphs, communication processes and Petri nets. In this report, we have used a PRES+ model (Petri net based Representation for Embedded Systems) as an extension of classical Petri net model that captures concurrency, timing behaviour of embedded systems; it allows systems to be representative in different levels of abstraction and improves expressiveness by allowing the token to carry information. Modeling using PRES+, as discussed above, may be convenient for specifying the input behaviour because it supports concurrency. However, there is no ...
We develop and investigate numerically a thermodynamically consistent model of two-dimensional multicomponent vesicles in an incompressible viscous fluid. The model is derived using an energy...Full Text Available
market is addressed through a move to a recycling-led area-based franchise model. ...market is addressed through a move to a recycling-led area-based franchise model.
Model selection aims to determine which theoretical models are most plausible given some data, without necessarily asking about the preferred values of the model parameters. A common model selection question is to ask when new data require introduction of an additional parameter, describing a newly-discovered physical effect. We review several model selection statistics, and then focus on use of the Bayesian evidence, which implements the usual Bayesian analysis framework at the level of models rather than parameters. We describe our CosmoNest code, which is the first computationally-efficient implementation of Bayesian model selection in a cosmological context. We apply it to recent WMAP satellite data, examining the need for a perturbation spectral index differing from the scale-invariant (Harrison-Zel'dovich) case.
Digital topographic models are the foundation of more advanced modeling applications and ultimately inform planning and decision making in many fields. Despite this, the error associated with these models and derived attributes is commonly overlooked. Little attention has been given in the scientific literature to the benefits gained from having less error in a model or to the corresponding cost associated with reducing model error by choosing one product over another. To address these gaps in knowledge we evaluated the error associated with five digital elevation models (DEMs) and derived attributes of slope and aspect relative to the same attributes derived from LiDAR data. We also estimated the acquisition and processing costs per square kilometer of the five test models and the LiDAR m...
Introduction:The purpose of this study was to utilize an in vitro biofilm model of subgingival plaque to investigate resistances in subgingival biofilm...Full Text Available
... time the terminal becomes active and begins the process of ... The model class considered here is of a single server queueing ... 1 I are both stochastic. ...
In the safety assessment of a high-level radioactive waste (HLW) disposal system, it is required to estimate radiological impacts on future human beings arising from potential radionuclide releases from a deep repository into the surface environment. In order to estimated the impacts, a biosphere model is developed by reasonably assuming radionuclide migration processes in the surface environment and relevant human lifestyles. It is important to modify the present biosphere models or to develop alternative biosphere models applying the biosphere models according to quality and quantify of the information acquired through the siting process for constructing the repository. In this study, alternative biosphere models were developed taking geosphere-biosphere interface of marine environment into account. Moreover, the flux to dose conversion factors calculated by these alternative ...
The authors solve the instability of perturbative vacuum of Gross-Neveu model. They use a variational method. The analysis is nonperturbative as it uses only equal time commmutator/anticommutator algebra.
In this model, without dark matter, the flat rotation curves of galaxies and the mass-to-light ratios of clusters of galaxies are described quantitatively. The hypothesis is that the agent of gravitational...Full Text Available
The morphology of human leukocytes, the biochemistry of actin polymerization, and the theory of continuum mechanics are used to model the pseudopod protrusion process of leukocytes. In the proposed...Full Text Available
May 31, 2011 ... A Theoretical Solid Oxide Fuel Cell Model for System Controls and Stability Design AUTHOR(S): Kopasakis, George; Brinson, Thomas; Credle, ...
Starting from the Plebanski formulation of gravity as a constrained BF theory we propose a new spin foam model for 4d Riemmanian quantum gravity that generalises the well-known model of Barrett-Crane and resolves the ultralocality problem that this model is known to possess. It is well known that the BF formulation of 4d gravity possesses two sectors: one corresponding to gravity and the other topological. The model presented here is shown to give a quantisation of the gravitational sector. The present model is dual to the recently proposed spin foam model of Engle et al. which, we show, corresponds to the topological sector of the theory. One important outcome of our approach is that it also allow us to introduce the Immirzi parameter into the framework of spin foam quantisation. We generalize some of our considerations to the Lorentzian setting and obtain a ...
This paper presents a new approach to improve the in silico modeling of ultrasound transducer arrays. While current simulation tools accurately predict the theoretical element...Full Text Available
IntroductionThe development of novel diagnostic agents for the detection of breast cancer microcalcifications requires a reliable animal model. Based on previous...Full Text Available
The thesis describes work undertaken as part of a larger remote sensing based project which aims to detect, measure and monitor coal fires in two test areas in northern China. The first main topic addressed in this thesis is the detection of fires using several different thermal remote sensing data sets. The synergistic use of the different data sets is emphasised. The second major part of the thesis deals with thermal modelling of the coal fires. Three different models are developed, which allow a fire's depth, temperature, extent, total heat output and rate of movement to be determined. The models are tested both in the laboratory and using various field data sets. A model based on the assumption that the fire is a point heat source and that the temperature distribution around it is spherically symmetrical is shown to be the most effective. A simpler, one-dimensional coal fire ...
In this study, drought analysis of annual flows of Jindong, Hyunpoong, and Waekwan stations located at Nakdong River Basins was performed based on multivariate stochastic models. The stochastic models used were multivariate autoregressive model(MAR) and multivariate contemporaneous (MCAR) model. MCAR(1) and MAR(1) models were selected to be appropriate models for these stations based on skewness test of normality, test of uncorrelated residuals, and correlograms of the residual series of each model. The statistics generated by MCAR(1) model and MAR(1) model resembled very closely those computed from historical series. The drought characteristics such as run length, run sum, and run intensity were fairly well reproduced for the various lengths of generated annual flows based on the MCAR(1) and MAR(1) ...
A numerical study of a natural convection in a rectangular cavity with the low-Reynolds-number differential stress and flux model is presented. The primary emphasis of the study is placed on the investigation of the accuracy and numerical stability of the low-Reynolds-number differential stress and flux model for a natural convection problem. The turbulence model considered in the study is that developed by Peeters and Henkes (1992) and further refined by Dol and Hanjalic (2001), and this model is applied to the prediction of a natural convection in a rectangular cavity together with the two-layer model, the shear stress transport model and the time-scale bound #upsilon#"2-f model, all with an algebraic heat flux model. The computed results are compared with the experimental data commonly used for the validation of the ...
Purpose: The aim of this study was to evaluate the accuracy of MRI in the measurement of cartilage thickness of the ankle joint in comparison to pathologic and histologic specimens. Patients and methods: The ankle joints of four fresh cadaver feet were imaged on a 1.5 T MR-unit in the coronal plane. Standard T{sub 1}-weighted spin echo (SE) and a T{sub 1}-weighted 3D-GE (FLASH-3D) sequence with fat saturation were applied. Following MR imaging, the talus was explanted and cut parallel to the MR images for macroscopic evaluation and histologic specimens were prepared. MRI measurements of the cartilage thickness of the talus were carried out in two ways: Without and with consideration of a transition zone of intermediate signal intensity between hyperintense cartilage and hypointense cortical bone. The data were compared with the anatomic specimens as the gold standard expressing the difference as a percentage value. On histologic specimens thickness of deep ...
The purpose of this study was to correlate histopathological with CT findings in patients suffering from hepatocellular carcinoma (HCC) eligible for orthotopic liver transplantation (OLT), with a special focus on the antitumoral effect of transarterial chemoembolization (TACE) therapy. A total of 42 consecutive patients suffering from HCC had been treated prior to OLT by means of TACE. TACE was carried out with a mixture of Lipiodol (10-20 ml) and mitomycin C (max. dosage, 10 mg). TACE was performed at 6- to 8-week intervals. Follow-up investigation included contrast-enhanced multislice CT controls and laboratory control. Liver explants were evaluated macroscopically and microscopically to determine the number and size of the tumor lesions as well as the degree of tumor necrosis. Necrosis was investigated in H and E-stained sections. The degree of necrosis was classified as follows: 0-25%, 26-50%, 51-75%, 75-99%, and complete necrosis. Two hundred thirty-one TACE ...
Warm-intermediate inflationary universe models in the context of braneworld cosmologies, are studied. This study is done in the weak and strong dissipative regimes. We find that, the scalar potentials and dissipation coefficients in terms of the scalar field, evolves as type-power-law and powers of logarithms, respectively. General conditions required for these models to be realizable are derived and discussed. We also study the scalar and tensor perturbations for each regime. We use recent astronomical observations to constraint the parameters appearing in the braneworld models.
We analyze the O(N) symmetric #sigma#-model in four dimensions with and without external source in the large-N approximation. We show that tachyons appear in these models only if cut-off effects are neglected. Including these effects and incorporating the triviality of the #sigma#-model, we demonstrate that no tachyon pole exists. We discuss how our results affect recent ideas to circumvent the 'no-loose-corollary' for W_L W_L scattering. (orig.).
Offers an updated version of French and Raven's bases of social power model and describes Raven's power/interaction model of interpersonal influence. Applies elements of both models to school consultation practices. Explores social power and influence occurring during school consultation. Describes a research agenda for further exploration of social power within consultation. (RJM)
We will examine modeling data for various orbits using modeling software and compare this with actual satellite flight result. In particular, we will discuss the contributions of trapped protons to total dose and the effectiveness of shielding.
We study the dynamics of the scalar tensor cosmological model in the presence of tachyon field. In an alternative approach, in two exponential and power law form of the scalar field functions in the model, field equations are solved by simultaneously best fitting the model parameters with the most recent observational data. This approach gives us an observationally verified interpretation of the dynamics of the universe. We then discuss the best fitted of equation of state parameter, the statefinder parameters and the reconstructed scalar field in the model.
An important aspect of water quality modeling is forecasting water quality variables for real-time management and control applications to enhance, maintain and sustain desirable water qualities. The major objective of this research is to develop daily time series models for forecasting river dissolved-oxygen (DO). The modeling approach adopted herein combines deterministic and stochastic concepts for determining properties of the DO process based on time series data and dynamic mechanisms governing the said process. This is accomplished by deriving a general DO stochastic model structure based on a modified Streeter-Phelps DO-BOD dynamic model. Then some types of nonlinear models namely, self-exciting threshold autoregressive-moving average (SETARMA), amplitude-dependent autoregressive (ADAR) and bilinear (BL) models, and the class of linear ...
DescriptionChanges in glacier mass balance are critically influenced by the distribution of snow accumulation at the start of the melt season, but models of the winter season lag seriously behind those of the melt season. The overall aim is to test physically-based models of the spatial and temporal evolution of the winter snowpack at a temperate ice cap (Langjokull, Iceland), to assess how effectively and also how efficiently they capture variation in winter accumulation. A three-step modelling approach i [continued...
The Finnish simulation code APROS and especially its 5-equation model is applied to modelling the horizontal steam generator. Different nodalizations are used in the secondary side of different models. Simulation results of the stationary state run are compared with results of RELAP5/MOD2 calculations and with an experimental plant data. (2 refs., 3 figs., 4 tabs.).
The Finnish simulation code APROS and especially its 5-equation model is applied to modelling the horizontal steam generator. Different nodalizations are used in the secondary side of different models. Simulation results of the stationary state run are compared with results of RELAP5/MOD2 calculations and with an experimental plant data. (2 refs., 3 figs., 4 tabs.).
The precipitation of excess silicon interstitials into dislocation loops is modeled. This situation occurs when an amorphous layer is created at the surface in order to avoid boron channeling and form shallow p junctions. The modeling of the nucleation of these extended defects is included into the process simulator IMPACT-4. Their density and mean radius are calculated for several annealing times and temperatures and they are compared with experimental characterizations. This is the first step towards a full modeling of the complex processes involved in the transient enhanced diffusion of boron.
This paper investigates the calculation of availability for parallel transmission lines (two or more) in the same tower or on the same right of way. As in many studies, the development of mathematical models is an important step. The models are justified using historical data and known characteristics of power system elements. A statistical method was used to generalize the failure rate and repair rate from real operating data. Application of the new model (which combines common-mode, simultaneous independent, and dependent outages) is discussed.
Due to their good hydraulic characteristic semi-axial pump turbines are used in the medium head range of pumped storage plants. This paper describes model tests performed on a semiaxial pump turbine model and shows the results of these tests. The aim of the model tests was the optimization of the hydraulic water passage, the measurement of the hydraulic characteristics over the whole operating range, the investigation of the cavitation behaviour, the investigation of the hydraulic forces and torques as well as the proof of the values guaranteed to the customer.
This paper outlines the development of an organizational model which will be used to determine the influence of supervisory and management functions in a nuclear power plant (NPP) on risk. A theoretical conceptualization, derived from the empirical literature, is used to describe the organizational structure of NPPs. The parameters and variables associated with this dynamic, process-oriented model are detailed. Applications of the model and preliminary insights derived from this conceptualization are discussed.
A mathematical model is proposed for three-phase filtering which is a particular case of a more general model of filtering multiple component mixtures and makes it possible to describe three-phase filtering flows under conditions where the pressure of saturation is variable in time and in space. In the proposed model, the system of unknown functions is selected so that it makes it possible to trace fairly simply the pressure of saturation and to compute the corresponding equation coefficients.
ABSTRACT Extending the unified theory of acceptance and use of technology (UTAUT) model, this study postulates a model of online social support. The model is empirically tested using data from undergraduates in Taiwan regarding their usage of instant messaging (IM). The test results indicate that all model paths are significant, except that the path between online social support and facilitating conditions is insignificant. This study offers limitations and implications.
The field algebra of the minimal models of W-algebras is amenable to a very simple description as a polynomial algebra generated by a few elementary fields, corresponding to order parameters. Using this description, the complete Landau-Ginzburg lagrangians for these models are obtained. Perturbing these lagrangians we can explore their phase diagrams, which correspond to multicritical points with D[sub n] symmetry. In particular, it is shown that there is a perturbation for which the phase structure is similar to that of the IRF models of Jimbo et al. (orig.)
The field algebra of the minimal models of W-algebras is amenable to a very simple description as a polynomial algebra generated by a few elementary fields, corresponding to order parameters. Using this description, the complete Landau-Ginzburg lagrangians for these models are obtained. Perturbing these lagrangians we can explore their phase diagrams, which correspond to multicritical points with D_n symmetry. In particular, it is shown that there is a perturbation for which the phase structure is similar to that of the IRF models of Jimbo et al. (orig.).
This analysis is one of 10 reports that support the Environmental Radiation Model for Yucca Mountain, Nevada (ERMYN) biosphere model. The ''Biosphere Model Report'' (BSC 2004 [DIRS 169460]) describes in detail the conceptual model as well as the mathematical model and its input parameters. This report documents development of input parameters for the biosphere model that are related to atmospheric mass loading and supports the use of the model to develop biosphere dose conversion factors (BDCFs). The biosphere model is one of a series of process models supporting the total system performance assessment (TSPA) for a Yucca Mountain repository. Inhalation Exposure Input Parameters for the Biosphere Model is one of five reports that develop input ...
The possibility of having inflation in a renormalizable cosmological model is investigated. The cosmic no-hair conjecture is proved to hold for all Bianchi types except Bianchi type IX. By the use of a conformal transformation on the metric we show that these models are equivalent to the ones described by the Einstein-Hilbert action for gravity minimally coupled to a set of scalar fields with inflationary potentials. Henceforth, we prove that inflationary solutions behave as attractors in solution space, making it a natural event in the evolution of such models.
The possibility of having inflation in a renormalizable cosmological model is investigated. The cosmic no-hair conjecture is proved to hold for all Bianchi types except Bianchi type IX. By the use of a conformal transformation on the metric we show that these models are equivalent to the ones described by the Einstein-Hilbert action for gravity minimally coupled to a set of scalar fields with inflationary potentials. Henceforth, we prove that inflationary solutions behave as attractors in solution space, making it a natural event in the evolution of such models.
A Lagrangian atmospheric dispersion model(K-LADM) combining a three dimensional sea-land breeze model has been developed and applied to the estimation of the quaterly and the annual averaged air tritium concentration around Wolsung NPP site. The estimated concentrations were compared with the observed concentration data. The results showed that the present Lagrangian Atmospheric dispersion model(K-LADM) provided very good agreement with the observations.
Li shell-model calculation has been made in the isospin formalism in the complete (0 + n)#Planck constant##omega# model space with the assumption of a closed core "4He. The calculation could probably be improved by use of a better effective interaction and increasing shell model space. With the use of faster computer with large memories, the authors are in hope of calculation in spsd shell-model space
In connection with the ERP project 'Dynamic modelling of staged gasification processes' a gasification simulator has been constructed. The simulator consists of: a mathematical model of the gasification process developed at Technical University of Denmark, a user interface programme, IGSS, and a communication interface between the two programmes. (BA)
We propose a dynamical model for business cycle based on an optimal DI model. In the model there exists a conserved quantity, which corresponds to the total energy in a dynamical system. We found that the business cycle with the period 6 or 7 years is nicely reproduced, since the model predicts a periodic motion in the conservative system.
DescriptionAn ability to foresee impacts on output is invaluable to any industry; good prediction is the basis of good management. Many research models can predict crop performance, but the skill (used here to include accuracy, precision, facility and credibility) of these predictions is rarely assessed, so is not well known. The only research model successfully adopted for practical purposes in the UK is the Broom's Barn Beet Model. Thus we propose here, research to assess and publish the skill of the [continued...
2D simulation modeling of a river basin is based on notion of a River Basin as an opened non equilibrium nature system. All components of the system (elevation, water, soil properties and others) are linked to single multi - functional model. The objective of flood simulation is one the model functions. The objectives of the paper are as follows: a mean scale basin floods computing and the model validation; a large scale basin simulation and demands for its validation; results and demands for flood hazard assessment. (orig.)
A simple and continuous model for the on-state current of polysilicon thin-film transistors, suitable for implementation in circuit simulators, is presented. The model includes the potential barrier at the grain boundaries, the channel length modulation and the excess current due to impact ionization. Comparison between measured output characteristics and the model shows excellent agreement over wide range of bias voltages and for devices with different gate lengths.
Abstract We address the fundamental question of matching the rest-frame K-band luminosity function (LF) of galaxies over the Hubble time using semi-analytic models after modification of the stellar population modelling. We include the Maraston evolutionary synthesis models, which feature a higher contribution by the thermally pulsating asymptotic giant branch (TP-AGB) stellar phase, into three different semi-analytic models, namely the De Lucia and Blaizot version of the Munich model, morgana and the Menci model. We leave all other input physics and parameters unchanged. We find that the modification of the stellar population emission can solve the mismatch between models and the observed rest-frame K-band luminosity from the brightest galaxies derived from UKIRT Infrared Deep Sky Survey d...
In this article, we propose a model selection method, the Bayesian composite model space approach, to map quantitative trait loci (QTL) in a half-sib population for continuous and binary traits. In our method, the identity-by-descent-based variance component model is used. To demonstrate the performance of this model, the method was applied to map QTL underlying production traits on BTA6 in a Chinese half-sib dairy cattle population. A total of four QTLs were detected, whereas only one QTL was identified using the traditional least square (LS) method. We also conducted two simulation experiments to validate the efficiency of our method. The results suggest that the proposed method based on a multiple-QTL model is efficient in mapping multiple QTL for an outbred half-sib population and is more powerful than the LS method based on a single-QTL model. PMID:21487433
Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The ...
Accurate modeling of the enhanced diffusion of boron during rapid thermal annealing has been accomplished by incorporating the effects of extended defect formation and annealing on enhanced diffusion into a multizone, semiempirical model. The multizone model divides the implant profile into three zones defining regions of different defects and diffusion enhancements. The model also contains the initial enhanced diffusion and the transient diffusion effects associated with the dissolution of defect clusters and the annealing of extended defects, respectively. The saturation time for transient-enhanced diffusion contains an exponential function of implant dose in order to model the increase in point defect generated with higher implant dose. As a result, the model accurately simulates the boron diffusion profile over a wide range of implant doses and also shows ...
We present an empirical model for periodic variations of diurnal and sub-diurnal Earth rotation parameters (ERPs) that was derived based on the transformation of normal equation (NEQ) systems of Very Long Baseline Interferometry (VLBI) observing sessions. NEQ systems that contain highly resolved polar motion and UT1-TAI with a temporal resolution of 15?min were generated and then transformed to the coefficients of the tidal ERP model to be solved for. To investigate the quality of this model, comparisons with empirical models from the Global Positioning System (GPS), another VLBI model and the model adopted by the conventions of the International Earth Rotation and Reference Systems Service (IERS) were performed. The absolute coefficients of these models agree almost completely within 7.5?...
This paper presents a patient specific deformable heart model that involves the known electrical and mechanical properties of the cardiac cells and tissue. The whole heart model comprises ten Tusscher's ventricular and Nygren's atrial cell models, the anatomical and electrophysiological model descriptions of the atria (introduced by Harrild et al.) and ventricle (given by Winslow et al.), and the mechanical model of the periodical cardiac contraction and resting phenomena proposed by Moireau et al. During the propagation of the depolarization wave, the kinetic, compositional and rotational anisotropy is handled by the tissue, organ and torso model. The applied patient specific parameters were determined by an evolutionary computation method. An intensive parameter reduction was performed u...
This paper describes a comprehensive model of wastewater treatment in secondary facultative ponds, which combines 3D hydrodynamics with a mechanistic water quality model. The hydrodynamics are based on the Navier-Stokes equation for incompressible fluids under shallow water and Boussinesq assumptions capturing the flow dynamics along length, breadth and depth of the pond. The water quality sub model is based on the Activated Sludge Model (ASM) concept, describing COD and nutrient removal as function of bacterial growth following Monod kinetics, except for Escherichia coli removal, which was modelled as first order decay. The model was implemented in the Delft3D software and was used to evaluate the effect of wind and the addition of baffles on the water flow pattern, temperature profiles i...