WorldWideScience
1

Heat treatment effect on impact strength of 40Kh steel  

Energy Technology Data Exchange (ETDEWEB)

The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented.

1984-01-01

2

Impact of Hight Velocity Cold Spray Particles  

Energy Technology Data Exchange (ETDEWEB)

This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric ...

1998-12-01

3

Weibel and Two-Stream Instabilities for Intense Charged Particle Beam Propagation through Neutralizing Background Plasma  

Energy Technology Data Exchange (ETDEWEB)

Properties of the multi-species electromagnetic Weibel and electrostatic two-stream instabilities are investigated for an intense ion beam propagating through background plasma. Assuming that the background plasma electrons provide complete charge and current neutralization, detailed linear stability properties are calculated within the framework of a macroscopic cold-fluid model for a wide range of system parameters.

2004-04-09

4

STUDY AND MODIFICATION OF CONVECTIVE STORMS  

Science.gov (United States)

... small water or ice particles by impaction ... flight recording; principally the hydrometeor charge unit ... capability of directing aircraft movements by radio ...

1963-06-30

5

A Review of Test Medium Contamination Effects on Test ...  

Science.gov (United States)

... solid particle contamination. Solid particulate impact is a good mechanism for surface heat transfer augmentation. The aug ...

1998-01-01

6

Embryo-damage induced nucleation of microcracks in an aluminum alloy under impact loading  

Energy Technology Data Exchange (ETDEWEB)

The nucleation of microdamage under dynamic loading was investigated through planar impact experiments accomplished with a light gas gun. The microscopic observation of recovered and sectioned specimens showed that microcracks were nucleated only by cracking of brittle particles inside material. However, for comparison the in situ static tensile tests on the same material conducted with a scanning electron microscope showed that the microcracks were nucleated by many forms those were fracture of ductile matrix, debonding particles from matrix and cracking of brittle particles. The quantitative metallographic observations of the specimens subjected to impact loading showed that most of the cracked particles were situated on grain boundaries of the aluminum matrix. These facts suggested the concept of critical size and incubation time of submicroscopic cavities in ...

1995-06-01

7

On virtual phonons, photons and electrons  

CERN Document Server

A macroscopic realization of the strange virtual particles is presented. The classical Helmholtz and the quantum mechanical Schr\\"odinger equations are analogous differential equations. Their imaginary solutions are called evanescent modes in the case of elastic and electromagnetic fields. In the case of non-relativistic quantum mechanical fields they are called tunneling solutions. The imaginary solutions of this differential equation point to strange consequences: They are non local, they are not observable, and they described as virtual particles. During the last two decades QED calculations of the imaginary solutions have been experimentally confirmed for phonons, photons, and for electrons. The experimental proofs of the predictions of the non-relativistic quantum mechanics and of the Wigner phase time approach for the elastic, the electromagnetic and the Schr\\"odinger fields will be presented in this article. The ...

2009-01-01

8

Strong laser fields as a probe for fundamental physics  

CERN Document Server

Upcoming high-intensity laser systems will be able to probe the quantum-induced nonlinear regime of electrodynamics. So far unobserved QED phenomena such as the discovery of a nonlinear response of the quantum vacuum to macroscopic electromagnetic fields can become accessible. In addition, such laser systems provide for a flexible tool for investigating fundamental physics. Primary goals consist in verifying so far unobserved QED phenomena. Moreover, strong-field experiments can search for new light but weakly interacting degrees of freedom and are thus complementary to accelerator-driven experiments. I review recent developments in this field, focusing on photon experiments in strong electromagnetic fields. The interaction of particle-physics candidates with photons and external fields can be parameterized by low-energy effective actions and typically predict characteristic optical signatures. I perform first estimates of the accessible ...

2008-01-01

9

Toughened semicrystalline engineering polymers: Morphology, impact resistance, and fracture mechanisms  

Energy Technology Data Exchange (ETDEWEB)

Major factors that contribute to maximized impact resistance of semicrystalline engineering polymers include increased matrix molecular weight, minimal rubber glass-transition temperature, and optimal rubber-particle size, which depends on matrix type. Additional constraints are posed by the limitations of available materials and commercial requirements. Expanding the understanding of impact-modified crystalline engineering polymers will further extend their property ranges and utility. This chapter describes the phenomenology of certain factors, illustrates a new technique to measure rubber particle size, and contrasts the fracture mechanisms of poly(butylene terephthalate), nylon 66, and polyacetal. 49 refs., 24 figs.

1993-12-31

10

Micromechanical modeling of ferrite-pearlite steels using finite element unit cell models  

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately ...

2000-11-01

12

Numerical study of semi-molten droplet impingement  

British Library Electronic Table of Contents (United Kingdom)

Due to the low thermal conductivity of ceramics large temperature gradients are present through the powder particles during plasma spray deposition. As a result the particles often impinge at the substrate in a semi-molten form; which in turn substantially affects the final characteristics of the coating being formed. This study is dedicated to the novel modelling development and simulation of a semi-molten droplet impingement. The study examines the impingement process during impact, spreading and solidification of semi-molten zirconia. The simulation provides an insight to the heat transfer process during impact and solidification of a semi-molten powder particle and illustrates the freezing-induced break-up mechanism at the splat periphery.

2011-01-01

13

EFFECTS OF QUARTZ PARTICLE SIZE AND SUCROSE ADDITION ON MELTING BEHAVIOR OF A MELTER FEED FOR HIGH-LEVEL GLASS  

Energy Technology Data Exchange (ETDEWEB)

The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 {micro}m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-{micro}m quartz particles; particles {ge}150 {micro}m formed clusters. Particles of 5 {micro}m completely dissolved by 900 C whereas particles {ge}150 {micro}m did not fully dissolve even when the temperature reached 1200 C. ...

2010-07-28

14

Plastic instability in an omega forming Ti-l5% Mo alloy  

International Nuclear Information System (INIS)

The plastic flow behavior of a #beta#-titanium alloy (Ti-15% Mo) was investigated over a wide range of temperatures and strain rates covering those conditions where the #omega#-phase forms dynamically. Portevin-Le Chatelier (PLC) effect was observed in this alloy at temperatures between 575 and 775 K at a strain rate of 1.31 x 10"-"4 s"-"1. The serrated flow behavior of this alloy could be suppressed by rendering the matrix #beta#-phase more stable against the #beta# to #omega# transformation. PLC bands formed in this alloy, studied at different levels of magnification using light, scanning electron and transmission electron microscopy, showed a high density of deformation bands within the macroscopic PLC band. The following mechanism of serrated flow is proposed; the load drop is ascribed to the sudden flow associated with the formation of deformation bands within which #omega#-particles were destroyed while the subsequent load rise results ...

15

Sociology and Space Development  

Science.gov (United States)

As the presence of humans in space expands in scope and duration, the quality of life in space as well as on Earth becomes pertinent. .... Military uses of space, such as the introduction of space-based laser or particle beam weapons, may have a major impact on the way people think and relate to .... AIAA Student Journal. ...

16

BY ORDER OF THE COMMANDER, 15TH AIR BASE WING - KSC SMA - NASA  

Science.gov (United States)

... 45 SW Staff and NASA on movement, intensity, weather conditions, ...... a) All surfaces of the vehicle susceptible to precipitation particle impact have been ... hydrometeors falling through the 0 deg C level and beginning to melt. ...

17

Nuclear scattering and suprathermal fusion  

Energy Technology Data Exchange (ETDEWEB)

The effect of nuclear scattering on the suprathermal fusion probability of recoiling d-t nuclei under the impact of fusion products, a 14.1-MeV neutron and a 3.5 MeV alpha particle, in thick pellets is investigated with the help of the Boltzmann-Fokker-Planck equation. Although the suprathermal fusion from alpha-particle recoils is quite small, the one originating from neutron recoils is considerable.

1987-11-01

18

Observation of dust stream formation produced by low current, high voltage cathode spots  

International Nuclear Information System (INIS)

Macroparticle acceleration driven by low current, high voltage cathode spots has been investigated for potential applications ranging from micrometeoroid simulation to nanoparticle deposition/implantation. Acceleration by this process was observed to occur when nanometer and micrometer-sized particles were exposed to a high voltage pulse in the presence of a plasma discharge. The applied negative voltage pulse initiates the formation of multiple, high voltage, low current cathode spots which provide the mechanism of actual acceleration of the charged dust particles. Dust streams generated by this process were detected using laser scattering techniques. Cathode spot behavior was also documented. The particle impact craters observed at the surface of downstream witness badges were documented using scanning electron microscopy and light microscopy. The observed impacts suggest the ...

2004-04-01

19

Strong-field quantum-electrodynamic processes in aligned crystals  

Energy Technology Data Exchange (ETDEWEB)

When a highly collimated beam of particles is aimed along the atomic rows of an aligned single crystal, the averaging effect of high speed motion results, to the lowest order of approximation, in crystal electric fields which are transverse to the atomic rows. The enormous magnitude of the crystal transverse electric fields is unsurpassed by any other known earth-bound macroscopic sources. For example, the field strengths along the <100> axis of tungsten at 77 K approach 9{center dot}10{sup 13}V/m. Thus quantum electrodynamic (QED) processes in strong fields which are thought to occur only in the extra-terrestrial environment can now be investigated in the laboratory. Here we review the results of measurements performed at the SPS facility in CERN using highly collimated beams of electrons, positrons and photons in the 20-200 GeV range, and germanium crystals cooled to 77 K with thicknesses ranging from 0.07 mm to 1.40 mm. The focus is on ...

1989-01-01

20

Skeletal remodeling dynamics: New approaches with imaging instrumentation  

Energy Technology Data Exchange (ETDEWEB)

This report of progress and future objectives timetable is based on an included schematic of goals and objectives and the project abstract which is included as Appendix 1. Five matters are summarized in the order of (1) novel methods of calcified bone confocal microscopy and reconstruction image analysis of decalcified beagle and human cortical bone serial sections, (2) macroscopic cross-correlation of beagle and human cortical and cancellous bone fractions with CT analysis, (3) guidance to the most radiobiologically important skeletal regions of interest with the just completed {sup 90}Sr bone tumor map from life time beagle studies, (4) deposition patterns of radioactive agents that participate in apatite crystal nucleation processes in bone and leave radiation-excited electrons trapped in bone mineral, and (5) the budget period timetable. The discovery that beta particles from {sup 166}Ho (T{sub {1/2}} =26 hr, {beta}{sub max} = 1.8 MeV) ...

1991-12-01

21

Quantum thermodynamics. Emergence of thermodynamic behavior within composite quantum systems. 2. ed.  

International Nuclear Information System (INIS)

This introductory text treats thermodynamics as an incomplete description of quantum systems with many degrees of freedom. Its main goal is to show that the approach to equilibrium -with equilibrium characterized by maximum ignorance about the open system of interest- neither requires that many particles nor is the precise way of partitioning, relevant for the salient features of equilibrium and equilibration. Furthermore, the text depicts that it is indeed quantum effects that are at work in bringing about thermodynamic behavior of modest-sized open systems, thus making Von Neumann's concept of entropy appear much more widely useful than sometimes feared, far beyond truly macroscopic systems in equilibrium. This significantly revised and expanded second edition pays more attention to the growing number of applications, especially non-equilibrium phenomena and thermodynamic processes of the nano-domain. In addition, to improve readability and ...

22

Characterization and Source Term Assessments of Radioactive Particles from Marshall Islands Using Non-Destructive Analytical Techniques  

Energy Technology Data Exchange (ETDEWEB)

A considerable fraction of radioactivity entering the environment from different nuclear events is associated with particles. The impact of these events can only be fully assessed where there is some knowledge about the mobility of particle bound radionuclides entering the environment. The behavior of particulate radionuclides is dependent on several factors, including the physical, chemical and redox state of the environment, the characteristics of the particles (e.g., the chemical composition, crystallinity and particle size) and on the oxidative state of radionuclides contained in the particles. Six plutonium-containing particles stemming from Runit Island soil (Marshall Islands) were characterized using non-destructive analytical and microanalytical methods. By determining the activity of {sup 239,240}Pu and {sup 241}Am isotopes from ...

2005-06-11

23

Identifying primary stressors impacting macroinvertebrates in the Salinas River (California, USA): Relative effects of pesticides and suspended particles  

International Nuclear Information System (INIS)

Laboratory dose-response experiments with organophosphate and pyrethroid pesticides, and dose-response experiments with increasing particle loads were used to determine which of these stressors were likely responsible for the toxicity and macroinvertebrate impacts previously observed in the Salinas River. Experiments were conducted with the amphipod Hyalella azteca, the baetid mayfly Procloeon sp., and the midge Chironomus dilutus (Shobanov, formerly Chironomus tentans). The results indicate the primary stressor impacting H. azteca was pesticides, including chlorpyrifos and permethrin. The mayfly Procloeon sp. was sensitive to chlorpyrifos and permethrin within the range of concentrations of these pesticides measured in the river. Chironomus dilutus were sensitive to chlorpyrifos within the ranges of concentrations measured in the river. None of the species tested were affected by turbidity as high as 1000 NTUs. The current ...

2006-06-01

24

The toughness amplification map of poly(vinyl chloride) and its cellulose acetate-compatibilized starch alloys containing core/shell rubber particles: Possible transition to super-toughening  

British Library Electronic Table of Contents (United Kingdom)

Abstract Toughening amplification of the neat poly(vinyl chloride) (PVC) and its reinforced version containing 25 phr of the cellulose acetate (CA)-compatibilized starch using methyl methacrylate-butadiene-styrene (MBS) core-shell particles was studied. The room temperature measured impact strength of the PVC showed mild increase up to 10 wt % with the addition of MBS particles. Then, the toughness enhanced discontinuously to super-tough plateau regime. The room temperature measured impact strength of PVC containing 20 phr of MBS particles, however, was reduced by as much as 95% when it was filled with 25 phr of the CA-compatibilized starch. In addition, the brittle-ductile transition (BDT) of the toughened PVC increased from 0 to 60 C because of its reinforcement, even though the matrix n...

2011-01-01

25

Evaluating the cytotoxicity of palladium/magnetite nano-catalysts intended for wastewater treatment  

International Nuclear Information System (INIS)

Palladium/magnetite nanoparticulate catalysts were developed for efficient elimination of halogenated organic pollutants from contaminated wastewater. Particle recovery from treated water can be ensured via magnetic separation. However, in worst-case scenarios, this catalyst removal step might fail, leading to particle release into the environment. Therefore, a toxicological study was conducted to investigate the impact of both pure magnetite and palladium/magnetite nanoparticle exposure upon human skin (HaCaT) and human colon (CaCo-2) cell lines and a cell line from rainbow trout gills (RTgill-W1). To quantify cell viability after particle exposure, three endpoints were examined for all tested cell lines. Additionally, the formation of reactive oxygen species was studied for the human cells. The results showed only minor effects of the particles on the tested cell systems and ...

2010-01-01

26

Effect of power supply ripple on emittance growth in the collider  

Energy Technology Data Exchange (ETDEWEB)

Power supply ripple at frequencies of 720 Hz and its harmonies is expected to affect the motion of particles in the collider. These ripple frequencies are nearly resonant with the betatron frequencies. To estimate the tolerable ripple levels, we have tracked particles through the complete nonlinear lattice for 10[sup 4] turns with ripple fed from 10 different power stations and including up to 7 different ripple frequencies. We presently estimate that relative ripple amplitudes must be below the 10[sup 8] level for there to be no significant impact on the emittance over the short term.

1993-05-01

27

Effect of power supply ripple on emittance growth in the collider  

Energy Technology Data Exchange (ETDEWEB)

Power supply ripple at frequencies of 720 Hz and its harmonies is expected to affect the motion of particles in the collider. These ripple frequencies are nearly resonant with the betatron frequencies. To estimate the tolerable ripple levels, we have tracked particles through the complete nonlinear lattice for 10{sup 4} turns with ripple fed from 10 different power stations and including up to 7 different ripple frequencies. We presently estimate that relative ripple amplitudes must be below the 10{sup 8} level for there to be no significant impact on the emittance over the short term.

1993-05-01

28

A Complete Detonator, Booster, and Main Charge Study of LX-07/PBX 9502  

British Library Electronic Table of Contents (United Kingdom)

Abstract A complete study of an exploding bridgewire detonator (EBW), an LX-07 hemispherical booster and a PBX 9502 outer shell are described. Breakout times from all three are listed in terms of first impact on the booster, i.e., code times. Lucite windows are also used to obtain particle velocities at the edges of each explosive, and these are converted into explosive pressures. The key to modeling is the use of the profile of the aluminum detonator can as it impacts the booster, i.e., we need to know the curvature of the end of the booster can. Modeling even with coarse zoning shows that (i) using reactive flow in the booster is better than programmed burn, (ii) creating the flyer curvature helps, and (iii) creating the time differences of flyer impact helps even more.

2011-01-01

29

A Four-Dimensional Probabilistic Atlas of the Human Brain  

UK PubMed Central (United Kingdom)

The authors describe the development of a four-dimensional atlas and reference system that includes both macroscopic and microscopic information on structure and function of the human brain in persons...Full Text Available

2001-09-01

30

Particle Swarm Optimization  

CERN Document Server

Particle Swarm Optimization

2006-01-01

31

The impact of solar flares and magnetic storms on humans  

International Nuclear Information System (INIS)

Three classes of solar emanations, namely, photon radiation from solar flares, solar energetic particles, and inhomogeneities in the solar wind that drive magnetic storms, are examined, and their effects on humans and technological systems are discussed. Solar flares may disrupt radio communications in the HF and VLF ranges. Energetic particles pose a special hazard at low-earth orbit and above, where they can penetrate barriers such as spacesuits and aluminum and destroy cells and solid state electronics. Energetic solar particles also influence terrestrial radio waves propagating through polar regions. Magnetic storms may disturb the operation of navigation instruments, power lines and pipelines, and satellites; they give rise to ionospheric storms which affect radio communication at all latitudes. There is also a growing body of evidence that changes in the geomagnetic field affect biological systems. 3 refs.

32

Prediction of drug particle size and content uniformity in low-dose solid dosage forms  

British Library Electronic Table of Contents (United Kingdom)

Drug particle size distribution has a profound impact to the content uniformity in low-dose solid drug products. We derived theoretically the skewness of potency distribution as a function of particle size distribution and target dose. It was demonstrated that both skewness and coefficient of variation diverge simultaneously with inverse square root of the target dose. This scaling relation was observed in recent experiment and was verified by Monte Carlo (MC) simulation, which was employed for the first time to solve for the full potency distribution from a random retrieving model. When tested against the criteria from USP uniformity of dosage units, MC simulation showed a striking anisotropic distribution of the data. This suggests a full-scale consideration of the potency distribu...

2010-01-01

33

Elastodynamics of vehicles and crash simulation  

Energy Technology Data Exchange (ETDEWEB)

Accidents of free-rolling cars against walls with friction are special cases of the general problem of the dynamic behavior (elastic or plastic) of car motion. Using particle modeling of the car body it is shown that large rotations, contact friction and plastic deformations can be computed. Because of the limitations of FEM it is necessary to model the car as a system of mass points connected by central force systems which are non-linear. The wall is formulated as a rigid body producing constraints for the contacting particles, while the contact force is given by the defined force system. Every contacting particle produces a plastic impact on the wall. The friction force is proportional to the contact force and lies in the direction of the sliding velocity on the wall. Time integration is carried out using a second order Gear method. ((orig.))

1994-09-30

34

Carbon effect on the structure and plasticity characteristics of titanium #beta#-alloys  

International Nuclear Information System (INIS)

In this paper a study is made of the structure and mechanical properties of the #beta# alloy system Ti-Mo-Zr-Sn (the composition of which is equivalent to the #beta# III alloy used abroad) containing different amounts of carbon. Study of the #beta#-titanium alloy containing 0.1% C revealed the presence of particles of titanium carbide. Separation of the titanium carbide promotes a reduction in impact strength, an increased tendency toward cold shortness, and poorer workability. (author).

35

Influences of particle sizes and contents of chemical blowing agents on foaming wood plastic composites prepared from poly(vinyl chloride) and rice hull  

British Library Electronic Table of Contents (United Kingdom)

This research aims to investigate the effects of chemical blowing agent (CBA) contents and particle sizes on the properties of foamed poly(vinyl chloride) (PVC)/rice hull (RH) composites. Fine particles of azodicarbonamide (AC) at 5, 8, 11 and 22mm were modified with 20% by weight of ZnO and used at 0-3.0% by weight. The average cell size and density of the PVC/RH foamed profiles were reduced as the content of modified azodicarbonamide (mAC) increased. Larger mAC particles lowered the density more effectively. Maximum reduction of density by 46% was achieved when mAC 22mm was applied at 2.0% by weight. Larger blowing particles led to PVC/RH foam with greater flexural modulus and strength. Greater impact strength, observed when 5mm mAC was applied, resulted from the rather thick cell wall c...

2011-01-01

36

Development of a new wear-resistant material: TiC/TiNi composite  

Energy Technology Data Exchange (ETDEWEB)

In this work, an attempt was made to develop a novel type of wear-resistant composite employing a TiNi alloy matrix reinforced by hard particles. Titanium carbide was chosen as the reinforcing phase because of its high hardness and TiNi alloy as the matrix due to its pseudoelasticity and good toughness. TiC particles may sustain external load, while the TiNi matrix may accommodate deformation, absorb impact energy and retain the hard particles. Such a combination is expected to lead to an enhanced wear resistance, compared to TiNi alloy. As a matter of fact, some efforts were previously made to develop TiNi-matrix composite reinforced by ceramic particles. However, the emphasis of those studies was put on effects of the reinforcing particles on the phase transformation behavior, shape memory effect and some mechanical properties of the composite; no attempt was ...

1999-10-22

37

Magnetization and magnetostriction curves for highly magnetostrictive materials  

Energy Technology Data Exchange (ETDEWEB)

The macroscopic behavior of magnetostrictive materials results from domain evolutions occurring at a microscopic scale. The author shows how to compute magnetization and magnetostriction curves by appraising the behavior of the underlying microstructures. The method hinges on an averaging device (Young measures), which allows one to pass from the microscopic to the macroscopic scale. He takes into account the kinematical constraints on the accommodation of elastic effects, and he highlights the role of material symmetry in the selection of energetically optimal microstructures.

1994-12-31

38

Shock characterization of TOAD pins  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this program was to characterize Time Of Arrival Detectors (TOAD) pins response to shock loading with respect to risetime, amplitude, repeatability and consistency. TOAD pins were subjected to impacts of 35 to 420 kilobars amplitude and approximately 1 ms pulse width to investigate the timing spread of four pins and the voltage output profile of the individual pins. Sets of pins were also aged at 45{degrees}, 60{degrees}, and 80{degrees}C for approximately nine weeks before shock testing at 315 kilobars impact stress. Four sets of pins were heated to 50.2{degrees}C (125{degrees}F) for approximately two hours and then impacted at either 50 or 315 kilobars. Also, four sets of pins were aged at 60{degrees}C for nine weeks and then heated to 50.2{degrees}C before shock testing at 50 and 315 kilobars impact stress, respectively. Particle velocity measurements at the ...

1995-08-01

39

Traffic flow optimization on rural networks  

Energy Technology Data Exchange (ETDEWEB)

Seasonal traffic on intercity corridors often creates severe congestion at various bottlenecks, such as land-drops and drawbridges. A Traffic Simulation And Optimization model (TSAO) has been developed in order to 1) evaluate traffic impacts (including travel time, vehicle operating costs, accidents, air pollution and fuel consumption) of a given routing pattern on a network, and 2) determine the optimal flow pattern. In its latest version, the TSAO model uses: 1) a macroscopic simulation approach to trace vehicle platoons through a network; 2) Greenshield's equation to represent volume-speed relationship on freeways and multi-lane highways, and Highway Capacity Manual method for two-lane rural highways; 3) Lighthill's shockwave function to simulate queue propagation; 4) event-scan time management for simulation; 5) variable link capacity for two-lane rural highways or to stimulate incidents; 6) AASHTO Guideline for ...

1983-01-01

40

Radiation hardening effects on localized deformation and stress corrosion cracking of stainless steels  

International Nuclear Information System (INIS)

Radiation hardening in austenitic stainless steels is shown to modify deformation characteristics and correlate well with an increased susceptibility to intergranular stress corrosion cracking (IGSCC). Available data on neutron-irradiated materials have been analyzed and correlations developed between fluence, yield strength and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 to 2.5 x10"2"1 n/cm"2) for IGSCC are documented. In many cases, this variability is consistent with yield strength differences among irradiated materials. IGSCC correlates better to yield strength than to fluence for most heats suggesting a possible role of radiation-induced hardening and microstructure on cracking. Microstructural evolution during proton and heavy-ion irradiation has been characterized in low-carbon 304SSs. Hardening results from a dispersion of dislocation loops in the matrix which increase in density and size with ...

1993-08-01

41

INTERACTING BINARIES WITH ECCENTRIC ORBITS. III. ORBITAL EVOLUTION DUE TO DIRECT IMPACT AND SELF-ACCRETION  

International Nuclear Information System (INIS)

The rapid circularization and synchronization of the stellar components in an eccentric binary system at the onset of Roche lobe overflow is a fundamental assumption common to all binary stellar evolution and population synthesis codes, even though the validity of this assumption is questionable both theoretically and observationally. Here we calculate the evolution of the orbital elements of an eccentric binary through the direct three-body integration of a massive particle ejected through the inner Lagrangian point of the donor star at periastron. The trajectory of this particle leads to three possible outcomes: direct accretion onto the companion star within a single orbit, self-accretion back onto the donor star within a single orbit, or a quasi-periodic orbit around the companion star, possibly leading to the formation of a disk. We calculate the secular evolution of the binary orbit in the first two cases and conclude that direct ...

2010-11-20

42

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

British Library Electronic Table of Contents (United Kingdom)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a 137Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data...

2010-01-01

43

Frequency distribution, isotopic composition and physical characterization of plutonium-bearing particles from the Fig-Quince zone on Runit Island, Enewetak Atoll  

British Library Electronic Table of Contents (United Kingdom)

Runit Island on Enewetak Atoll was very heavily impacted by the U.S. nuclear testing campaign in the northern Marshall Islands (1946?58). The primary source of contamination on Runit Island was the 1958 Quince safety test where a large quantity of device plutonium (Pu) was scattered over the area near the GZ. A second low-yield device was detonated on the same site 10?days later, further disturbing the soil and leaving behind a very heterogeneous pattern of contamination including milligram-size particles of plutonium. A limited cleanup of the Fig-Quince zone was carried out in 1979. During this period, the effectiveness of the cleanup operations was primarily evaluated on the basis of bulk soil concentration data with little consideration given to the heterogeneity and long-term material-...

2009-01-01

44

A numerical investigation of scale-up effects on coke yields of a thermal cracking Riser reactor  

Energy Technology Data Exchange (ETDEWEB)

A validated computational fluid dynamics (CFD) computer code, ICRKFLO, was used to investigate the scale-up effects on the coke yields of thermal cracking riser factors. Comparisons were made for calculated coke yields of pilot- and commercial-scales riser units. Computational results show that the riser aspect ratio, reaction temperature, particle residence time, and particle/oil ratio have major impacts on the coke yield. A computational experiment was conducted to determine optimal operating conditions for a conceptual design of a commercial-scale riser unit. This experiment showed that the performance loss in scale-up from pilot to commercial scale may be almost completely recovered through optimizing the operating conditions after scale-up using the CFD simulations as a guide.

1995-05-01

45

Modeling of ablation by photospallation using the computer program PUFF/DFRACT  

Energy Technology Data Exchange (ETDEWEB)

In general, macroscopic material failure is a manifestation of irreversible changes at the microscopic level. Many tissues, which may appear to be macroscopically homogeneous, are, at a fundamental microscopic level, a composite material. For example, cornea is composed of a hyaluronic acid matrix in which layers of collagen fibers are overlaid in a crossing pattern. The points where the collagen fibers intersect are potential nucleation sites for microscopic defects, which under the action of tensile stress, nucleate, grow and coalesce to form macroscopic failure planes, or spall planes. Using a model based on microstructural evolution, this paper examines the failure process during photoablation. Specifically, the paper describes a physically motivated, micromechanical model based on the nucleation and growth of spherical voids. This model is then used to simulate photoablation of cornea. Potential for using this model to ...

1995-03-01

46

New techniques for electron-ion collision studies  

International Nuclear Information System (INIS)

We have constructed an apparatus to study electron impact ionization of ions which should provide additional insight into the mechanisms involved. Using multiparameter coincidence techniques, we will detect both outgoing electrons from ionization process and will be able to analyze the momenta of both particles simultaneously. Coupled with a high resolution electron gun, this information should have broad application to the difficult problem of three bodies interacting via the long range Coulomb force. If sufficient accuracy can be achieved, information regarding the relative phase of the outgoing electron wavefunctions can be obtained.

47

Peptides of human bronchial mucus glycoproteins. Size determination by electron microscopy and by biosynthetic experiments.  

UK PubMed Central (United Kingdom)

Secreted human bronchial mucins, directly collected from macroscopically healthy bronchial mucosa, were prepared in the presence of six proteinase inhibitors, and analysed by electron microscopy. These...Full Text Available

1987-11-15

48

Residual stress measurements on a stress relieved Zircaloy-4 weld by neutron diffraction  

Energy Technology Data Exchange (ETDEWEB)

The macroscopic stress distribution across an annealed Zircaloy-4 gas tungsten arc weld was measured by neutron time-of-flight diffraction at the SMARTS diffractometer at Los Alamos National Laboratory. The stresses after annealing are about 40% lower than those in the same weld prior to heat treatment. The intergranular strains in the reference coupons, which give the macroscopic stress free lattice spacings, are consistent with the difference in cooling the strongly textured plate and the weakly textured weld.

2006-12-15

49

MACROSCOPIC ONTOLOGY IN EVERETTIAN QUANTUM MECHANICS  

British Library Electronic Table of Contents (United Kingdom)

Abstract Simon Saunders and David Wallace have proposed an attractive semantics for interpreting linguistic communities embedded in an Everettian multiverse. It provides a charitable interpretation of our ordinary talk about the future, and allows us to retain a principle of bivalence for propositions and to retain the law of excluded middle in the logic of propositions about the future. But difficulties arise when it comes to providing an appropriate account of the metaphysics of macroscopic objects and events. I evaluate various metaphysical frameworks which might be combined with the Saunders-Wallace semantics. I conclude that the most appropriate metaphysics to underwrite the semantics renders Everettian quantum mechanics a theory of non-overlapping worlds.

2011-01-01

50

Measurement of the triple gauge-boson couplings {gamma}WW and ZWW in ALEPH and at LEP; Mesure des couplages {gamma}WW et ZWW dans ALEPH et au LEP  

Energy Technology Data Exchange (ETDEWEB)

This document deals with the couplings between the W boson and Z and gamma particles. WWZ and WW{gamma} vertex are predicted by the electroweak theory based on the symmetry group SU(2){sub L}*U(1){sub Y}, their existence is confirmed by the measurement of the production cross-section of W pairs at LEP. The effective values of the couplings are modified by the introduction of standard model particle loops at the vertex level, the impact on the coupling value is assessed to reach 10{sup -3}. These loops can also include beyond-the-standard-model particles, their impact is in the magnitude order of 10{sup -3} for most models. The fully description of these loops requires the values of 14 complex parameters whose measurement will give information about the existence of new particles. Nevertheless the number of events at LEP is not sufficient to measure all the ...

2005-03-15

51

Frequency distribution, isotopic composition and physical characterization of plutonium-bearing particles from the Fig-Quince zone on Runit Island, Enewetak Atoll  

International Nuclear Information System (INIS)

Runit Island on Enewetak Atoll was very heavily impacted by the U.S. nuclear testing campaign in the northern Marshall Islands (1946-58). The primary source of contamination on Runit Island was the 1958 Quince safety test where a large quantity of device plutonium (Pu) was scattered over the area near the GZ. A second low-yield device was detonated on the same site 10 days later, further disturbing the soil and leaving behind a very heterogeneous pattern of contamination including milligram-size particles of plutonium. A limited cleanup of the Fig-Quince zone was carried out in 1979. During this period, the effectiveness of the cleanup operations was primarily evaluated on the basis of bulk soil concentration data with little consideration given to the heterogeneity and long-term material-, biological-, and environmental-specific impacts of residual high activity (hot) particle contamination. The aim of ...

2009-12-01

52

Particle Detection with drift Chambers  

CERN Document Server

Particle Detection with drift Chambers

2008-01-01

55

Production of negative ions by electron impact. Final report 1 May 81-31 Oct 82  

Science.gov (United States)

Proposed future space-based beam weapons systems will most probably require an intense neutral particle beam for effective operation across geomagnetic field lines. Such neutral beams can most efficiently be obtained by stripping excess electrons from negative ion beams. The objective of this work is to study the process of dissociative attachment of electrons. Specifically, to measure the cross sections for polar dissociation and dissociative attachment for production of H(-). It is suspected that these dissociative attachment cross sections for the production of H(-) from alkali hydrides are large. The insight gained from this study will be extremely helpful in the fabrication of high current density H(-) beam sources for use in the production of intense neutral hydrogen beams. A selection of alkali hydride molecules will be investigated in order to determine the largest cross sections for the production of H(-) by electron impact. The ...

1982-10-01

56

Hydrologic analysis for ecological risk assessment of watersheds with abandoned mine lands  

International Nuclear Information System (INIS)

As part of on-going study of acid mine drainage (AMD), a comprehensive ecological risk assessment was conducted in the Leading Creek Watershed in southeast Ohio. The watershed is influenced by agriculture and active and abandoned coal-mining operations. This work presents a broad overview of several quantitative measures of hydrology and hydraulic watershed properties available for in risk assessment and evaluates their relation to metrics of ecology. Data analysis included statistical comparisons of metrics of ecology, ecotoxicology, water quality, and physically based parameters describing land use, geomorphology, flow, velocity, and particle size. A multiple regression analysis indicated that abandoned mining operations dominated impacts upon aquatic ecology. It also indicated low flow velocity measurements and a ratio of maximum velocity to average velocity at low flow where helpful in describing variation in macroinvertebrate Total Taxa ...

1999-07-25

57

Thermal loads on tokamak plasma-facing components during normal operation and disruptions  

Energy Technology Data Exchange (ETDEWEB)

Power loadings experienced by tokamak plasma-facing components during normal operation and during off-normal events are discussed. A model for power and particle flow in the tokamak boundary layer is presented and model predictions are compared to infrared measurements of component heating. The inclusion of the full three-dimensional geometry of the components and of the magnetic flux surface is very important in the modeling. Experimental measurements show that misalignment of component armour tile surfaces by only a millimeter can lead to significant localized heating. An application to the design of plasma-facing components for future machines is presented. Finally, thermal loads expected during tokamak disruptions are discussed. The primary problems are surface melting and vaporization due to localized intense heating during the disruption thermal quench and volumetric heating of the component armour and structure due to localised impact of ...

1990-01-01

58

Sizing pumps for slurries  

Energy Technology Data Exchange (ETDEWEB)

Slurry characteristics have a significant impact on centrifugal pump performance. For instance, as particle size increases or the percent solids concentration increases, pump head and efficiency decrease. Therefore, before a slurry pump is selected, it is important to define the slurry characteristics as accurately as possible. The effect of the slurry characteristics on the head and efficiency of the centrifugal pump will be emphasized (the effect on flowrate is less significant). The effect of slurry characteristics is more predominant in smaller pumps (with smaller diameter impellers) than in larger pumps. The data and relationship between the various slurry parameters have been developed from correlations and nomographs published by pump vendors from their field data and test results. The information helps to avoid specifying an undersized pump/motor assembly for slurry service.

1996-11-01

59

QCD corrections to top quark pair production in association with a photon at hadron colliders  

CERN Document Server

We compute QCD corrections to the production of a ttbar pair in association with a hard photon at the Tevatron and the LHC. This process allows a direct measurement of the top quark electromagnetic couplings that, at the moment, are only loosely constrained. We include top quark decays, treating them in the narrow width approximation, and retain spin correlations of final-state particles. Photon radiation off top quark decay products is included in our calculation and yields a significant contribution to the cross-section. We study next-to-leading order QCD corrections to the ppbar -> ttbar+gamma process at the Tevatron for the selection criteria used in a recent measurement by the CDF collaboration. We also discuss the impact of QCD corrections to the pp -> ttbar+gamma process on the measurement of the top quark electric charge at the 14 TeV LHC.

2011-01-01

60

Impact of the addition of chicken litter on mercury speciation and emissions from coal combustion in a laboratory-scale fluidized bed combustor  

Energy Technology Data Exchange (ETDEWEB)

Co-combustion of chicken litter with coal was performed in a laboratory-scale fluidized bed combustor to investigate the effect of chicken litter addition on the partitioning behavior of mercury. Gaseous total and elemental mercury concentrations in the flue gas were measured online, and ash was analyzed for particle-bound mercury along with other elemental and surface properties. The mercury mass balance was between 85 and 105%. The experimental results show that co-combustion of chicken litter decreases the amount of elemental and total mercury in the gas phase. Mercury content in fly ash increases with an increasing chicken litter share. 22 refs., 6 figs., 5 tabs.

2008-07-15

61

Transport of sorbing solutes in randomly heterogeneous formations: Spatial moments, macrodispersion, and parameter uncertainty  

Energy Technology Data Exchange (ETDEWEB)

Expressions for the spatial moments and macrodispersion tensor for sorbing solutes in heterogeneous formations were presented using a probabilistic model of a fluid residence time coupled with the particle position analysis. The fluid residence time was defined as a fraction of the actual time during which the particle stayed in the mobile fluid phase of the aquifer. The fluid residence time is a random variable whose variability comes as a result of the non-equilibrium sorption properties. The sorbing solute was assumed to be governed with first-order linear kinetics. The closed-form expressions were based on the stationarity in the kinetic process and on the first-order approximation in the hydraulic conductivity field and in the fluid residence time. The non-equilibrium effects were presented as a function of the spatial variability in hydraulic conductivity and temporal variability in the fluid residence time. The importance of the ...

1993-06-01

62

The Development of a Neutral Particle Detector for Observations of the Thermosphere  

Science.gov (United States)

One of the least understood regions of the upper atmosphere is the thermosphere, principally due to the difficulty of making observations. The neutral atmosphere is known to be highly variable, and its composition and density varies by several orders of magnitude due to solar activity, diurnal cycles, latitude, geomagnetic activity, and gravity waves. In the past, most in-situ measurements of the neutral atmosphere have utilized detectors that are dependent on arrival angle and energy accommodation of incoming species, so that information related to nascent velocity distribution and reactive species abundances is often masked. This paper will review design concepts and laboratory tests related to the development of a novel open-ionizer, neutral particle detector for space environment measurements which can overcome these limitations. The sensor features a very large field-of-view suitable for sounding rocket missions. This time-of-flight instrument uses ...

2006-12-01

63

Electrification of a PTFE particle by impact on a metal plate. Tefuron ryushi no kinzokuban tono shototsu ni yoru taidensei  

Energy Technology Data Exchange (ETDEWEB)

Electrification of Teflon (PTFE) particles pneumatically transported while repeating collision with the wall is different from the cases of nylon 66 or PMMA. PTFE is known as negatively charging substance. Extremely little electrification was found when vertically colliding to the wall. By experiments, it was found that: 1. In the case of vertical collision, electrification was extremely low. 2. Chareg amount by collision increases as v cos increases when it is less than 7.5 m/s in a condition that a horizontal component of a collision speed is present. When v cos is more than 7.5 m/s, the charge approaches that of vertical collision. 3. Measured value of collision area roughly coincided with the result of calculation using an equation based on the assumption that the deforamtion depended only on the vertical component of the collision speed. 4. Charge density gets larger for less v cos and more v sin . Charge density of PTFE which was measured this time was (-1.56 ...

1990-07-31

64

Computer modeling of oil spill trajectories with a high accuracy method  

Energy Technology Data Exchange (ETDEWEB)

This paper proposes a high accuracy numerical method to model oil spill trajectories using a particle-tracking algorithm. The Euler method, used to calculate oil trajectories, can give adequate solutions in most open ocean applications. However, this method may not predict accurate particle trajectories in certain highly non-uniform velocity fields near coastal zones or in river problems. Simple numerical experiments show that the Euler method may also introduce artificial numerical dispersion that could lead to overestimation of spill areas. This article proposes a fourth-order Runge-Kutta method with fourth-order velocity interpolation to calculate oil trajectories that minimise these problems. The algorithm is implemented in the OilTrack model to predict oil trajectories following the 'Nissos Amorgos' oil spill accident that occurred in the Gulf of Venezuela in 1997. Despite lack of adequate field information, model results ...

1999-07-01

65

Characterisation of a re-cast composite Nafion 1100 series of proton exchange membranes incorporating inert inorganic oxide particles  

International Nuclear Information System (INIS)

A series of cation exchange membranes was produced by impregnating and coating both sides of a quartz web with a Nafion solution (1100 EW, 10%wt in water). Inert filler particles (SiO_2, ZrO_2 or TiO_2; 5-20%wt) were incorporated into the aqueous Nafion solution to produce robust, composite membranes. Ion-exchange capacity/equivalent weight, water take-up, thickness change on hydration and ionic and electrical conductivity were measured in 1 mol dm"-"3 sulfuric acid at 298 K. The TiO_2 filler significantly impacted on these properties, producing higher water take-up and increased conductivity. Such membranes may be beneficial for proton exchange membrane (PEM) fuel cell operation at low humidification. The PEM fuel cell performance of the composite membranes containing SiO_2 fillers was examined in a Ballard Mark 5E unit cell. While the use of composite membranes offers a cost reduction, the unit cell performance was reduced, in practice, due ...

2010-09-01

66

Spent fuel sabotage aerosol ratio program : FY 2004 test and data summary  

International Nuclear Information System (INIS)

This multinational, multi-phase spent fuel sabotage test program is quantifying the aerosol particles produced when the products of a high energy density device (HEDD) interact with and explosively particulate test rodlets that contain pellets of either surrogate materials or actual spent fuel. This program has been underway for several years. This program provides data that are relevant to some sabotage scenarios in relation to spent fuel transport and storage casks, and associated risk assessments. The program also provides significant technical and political benefits in international cooperation. We are quantifying the Spent Fuel Ratio (SFR), the ratio of the aerosol particles released from HEDD-impacted actual spent fuel to the aerosol particles produced from surrogate materials, measured under closely matched test conditions, in a contained test chamber. In addition, we are measuring the amounts, ...

67

How does sorbent particle structure influence sulfur capture under PFBC conditions?  

Energy Technology Data Exchange (ETDEWEB)

The physical structure of a limestone or dolomite to be used in in-bed sulfur capture in fluidized bed boilers has great impact on the efficiency of sulfur capture and sorbent use. Therefore in process optimization and model calculations parameters describing the pore structure of these sorbents must be included. In this study an unreacted shrinking core model with variable effective diffusivity is applied to sulfation test data from a pressurized thermogravimetric apparatus (P-TGA) for various limestone and dolomite samples. The particle size was 250--300 {micro}m for all sorbents. The tests were done under typical conditions for a pressurized fluidized bed combustor, i.e. 850 C or 950 C, 15 bar, and were reported earlier at the 12th International Conference on Fluidized Bed Combustion. At these conditions the limestone remains uncalcined, while the dolomite is half-calcined. The sorbents were characterized by chemical composition analysis, ...

1995-12-31

68

Sub-barrier fusion reactions for synthesis of "2"9"8114  

International Nuclear Information System (INIS)

Favorable reaction channels are searched for in order to obtain the superheavy element "2"9"8114. The interaction energy is supposed to comply with the adiabatic hypothesis. Concerning the deformation energy, a very complete binary macroscopic-microscopic energy method is used to perform calculations. Deformed two-center shell model provides the energy level schemes for shell effects. Yukawa-plus-exponential model gives the macroscopic (liquid drop) part of the total energy. The mass tensor is obtained by the Werner-Wheeler irrotational flow hypothesis. Finally the minimization of the multidimensional action integral produces the highest penetrability values. Kr-projectile reactions provide the best pairs, although generally the presentabilities are very low. (author)

2005-01-01

69

Coherent spontaneous radiation of Frenkel excitons  

International Nuclear Information System (INIS)

We have constructed a mathematical model that describes the coherent spontaneous radiation of a macroscopically filled exciton mode. We have demonstrated qualitatively ways in which a coherent subsystem of excitons can be formed. When this occurs under the influence of an external coherent source, exciton free induction occurs, while in the case of a spontaneous transition of the excitons to a coherent state through freezing of the reservoir of intermolecular interactions superradiance occurs. We have concluded that superradiance in the system of Frenkel excitons is possible under the influence of the non-Dicke mechanisms of self-induction of correlations, when the dipole transition moments of the individual atoms are coupled into a single macroscopic effective spin through their electrostatic interaction, this being analogous to the ordering of magnetic dipole moments in a ferromagnet.

1988-01-01

70

Anomalous properties of the local dynamics in polymer glasses  

CERN Document Server

The emergence of nanoscience has increased the importance of experiments able to probe the very local structure of materials, especially for disordered and heterogeneous systems. This is technologically important; for example, the nanoscale structure of glassy polymers has a direct correlation with their macroscopic physical properties. We have discovered how a local, high frequency dynamic process can be used to monitor and even predict macroscopic behavior in glassy polymers. Polyvinylethylenes vitrified by different chemical and thermodynamic pathways exhibit different densities in the glassy state. We find that the rate and amplitude of a high frequency relaxation mode (the Johari-Goldstein process involving local motion of segments of the chain backbone) can either correlate or anti-correlate with the density. This implies that neither the unoccupied (free) volume nor the configurational entropy governs the local dynamics in any general ...

2008-01-01

71

Correlation between particle size, in vivo particle persistence, and lung injury.  

UK PubMed Central (United Kingdom)

Dosimetry parameters such as deposition, clearance, retention, and translocation and dissolution of inhaled particles in and to different lung compartments may be important for the persistence of particles...Full Text Available

1994-10-01

72

Aging of Pentaerythritol Tetranitrate (PETN)  

Science.gov (United States)

Pentaerythritol tetranitrate (PETN) is a relatively sensitive explosive used in many electroexplosive devices as well as in medicine. Of primary interest to LLNL is its use in items such as exploding bridgewire (EBW) detonators and exploding bridge foil initiators (EFI). In these devices the crystalline powder is pressed into a granular, low-density compact that can be initiated by an exploding wire or foil. The long-term stability of this pressed compact is of interest to weapon stockpile lifetime prediction studies. Key points about potential aging mechanisms can be summarized as follows: (1) There are a number of factors that can contribute to PETN instability. These include particle size, polymorphic phase transitions, crystal structure, impurities, moisture, occlusions, chemical incompatibility and biological (microorganism) action. of these factors the most important for long-term aging of high surface area powders used in detonators appears to be that of ...

2009-04-22

73

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio program  

Energy Technology Data Exchange (ETDEWEB)

We provide a detailed overview of an ongoing, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high energy density device, HEDD. The program participants in the U.S. plus Germany, France, and the U.K., part of the international Working Group for Sabotage Concerns of Transport and Storage Casks, WGSTSC have strongly supported and coordinated this research program. Sandia National Laboratories, SNL, has the lead role for conducting this research program; test program support is provided by both the U.S. Department of Energy and Nuclear Regulatory Commission. WGSTSC partners need this research to better understand potential radiological impacts from sabotage of nuclear ...

2004-07-01

74

Relativistic effects on chaos. Loss mechanism of runaway electrons in a tokamak  

Energy Technology Data Exchange (ETDEWEB)

The relativistic motion of an electron is numerically analyzed in a tokamak having macroscopic magnetic turbulence. Stochasticity induced by the relativistic motion overwhelms the phase averaging effect, which provides a tokamak with an effective loss mechanism for the avoidance/suppression of runaway electron generation at a major disruption. On the other hand, electrons in the KAM (Kolmogorov-Arnold-Moser) region will be observed as a runaway snake. (author)

2001-12-01

75

Polysulfone/Metal Nanocomposites by Simultaneous Photoinduced Crosslinking and Redox Reaction  

British Library Electronic Table of Contents (United Kingdom)

Abstract A diacrylate polysulfone oligomer is synthesized and used as the acrylic oligomer for the in situ synthesis of noble metal/PSU nanocomposites through UV-induced simultaneous radical polymerization of acrylic functionalities and NP formation by reduction of their precursors. Thus, silver or gold NPs are formed in situ during polymer network formation. FESEM analysis of the morphology of the cured systems demonstrates that the nanoparticles of the noble metals are homogeneously distributed in the network without macroscopic agglomeration.

2011-01-01

76

Effect of ultrasonic waves on boiling heat transfer. 2  

International Nuclear Information System (INIS)

This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic steam induced by ultrasonics is a major contribution to heat transfer augmentation. (author).

1993-05-01

77

Effect of ultrasonic waves on boiling heat transfer  

Energy Technology Data Exchange (ETDEWEB)

This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic stream induced by ultrasonics is a major contribution to heat transfer augmentation. (author).

1993-07-01

78

EPA (ENVIRONMENTAL PROTECTION AGENCY) MACROSCOPIC PLANNING MODEL (EPAMAC) FOR STORMWATER AND COMBINED SEWER OVERFLOW CONTROL: APPLICATION GUIDE AND USER'S MANUAL  

Science.gov (United States)

A simplified stormwater management model has been developed to provide an inexpensive, flexible tool for planning and preliminary sizing of stormwater facilities. The model was developed to be part of a methodology for use in the management of stormwater that utilizes both simple...

79

(Photoexcited charge pair escape and recombination)  

Science.gov (United States)

Progress in four research areas on this project are summarized under the following topics: (1) Geminate charge pair recombination in hexane; (2) Fast current measurements resulting from excitation of charge transfer (CT) states; (3) Measurement of the dipole moment of excited states by DC conductivity; and (4) Charge separation at macroscopic interfaces between electron donor and acceptor solids. In a final section, personnel who have contributed to the project during the past budget period are described.

1990-01-01

80

How do we impact corrosion?  

Science.gov (United States)

Page 1. How do we impact corrosion? US Army Corrosion Summit Feb. ... Page 4. Leaders in Corrosion Control Technology Impact of Corrosion - $$ ...

2009-02-03

81

Space Radiation Detector with Spherical Geometry  

Science.gov (United States)

A particle detector is provided, the particle detector including a spherical Cherenkov detector, and

2011-01-01

82

Flawless start for world's mightiest particle collider  

CERN Document Server

Flawless start for world's mightiest particle collider

2008-01-01

84

Simulating Dynamic Stall in a 2D VAWT: Modeling strategy, verification and validation with Particle Image Velocimetry data  

International Nuclear Information System (INIS)

The implementation of wind energy conversion systems in the built environment renewed the interest and the research on Vertical Axis Wind Turbines (VAWT), which in this application present several advantages over Horizontal Axis Wind Turbines (HAWT). The VAWT has an inherent unsteady aerodynamic behavior due to the variation of angle of attack with the angle of rotation, perceived velocity and consequentially Reynolds number. The phenomenon of dynamic stall is then an intrinsic effect of the operation of a Vertical Axis Wind Turbine at low tip speed ratios, having a significant impact in both loads and power. The complexity of the unsteady aerodynamics of the VAWT makes it extremely attractive to be analyzed using Computational Fluid Dynamics (CFD) models, where an approximation of the continuity and momentum equations of the Navier-Stokes equations set is solved. The complexity of the problem and the need for new design approaches for VAWT for the built ...

2007-07-01

87

Shock and Impact Response of Naval Composite Structures  

Science.gov (United States)

... at the end of this report. A. Low-Velocity Impact of Composite Sandwich Panels In 2007, the PI developed analytical solutions ...

2010-08-09

88

Assessment of the radiological impact of the 50 GeV BPS on its environment In Chinese  

CERN Document Server

Assessment of the radiological impact of the 50 GeV BPS on its environment

1980-01-01

89

Visualization by PIV of dynamic stall on a vertical axis wind turbine  

Energy Technology Data Exchange (ETDEWEB)

The aerodynamic behavior of a vertical axis wind turbine (VAWT) is analyzed by means of 2D particle image velocimetry (PIV), focusing on the development of dynamic stall at different tip speed ratios. The VAWT has an unsteady aerodynamic behavior due to the variation with the azimuth angle {theta} of the blade's sections' angle of attack, perceived velocity and Reynolds number. The phenomenon of dynamic stall is then an inherent effect of the operation of a VAWT at low tip speed ratios, impacting both loads and power. The present work is driven by the need to understand this phenomenon, by visualizing and quantifying it, and to create a database for model validation. The experimental method uses PIV to visualize the development of the flow over the suction side of the airfoil for two different reference Reynolds numbers and three tip speed ratios in the operational regime of a small urban wind turbine. The field-of-view of the ...

2009-01-15

90

Potentials of biofuels  

Energy Technology Data Exchange (ETDEWEB)

This paper discussed the potential of biofuels with particular reference to the situation in Germany and Europe. Emphasis was on technical potential, such as biofuel production, utilization and environmental aspects. The Institute of Agricultural Technology and Biosystems Engineering ran vTI emission tests on diesel engines to evaluate the environmental impacts of biofuels. This testing facility is able to drive heavy-duty diesel engines in both stationary and dynamic test cycles, such as the European ESC and ETC. Additional analyses were conducted to determine the fine and ultra-fine particles, polycyclic aromatic hydrocarbons (PAH), aldehydes, ketones, and the usual regulated exhaust gas compounds. Ames tests were conducted to assess the mutagenic potential of tailpipe emissions. Previous study results showed that neat vegetable oils can render the exhaust high in mutagenic potency. Some of the non-regulated exhaust gas compounds were found ...

2010-07-01

91

Optical modules for the neutrino telescope KM3NeT  

Energy Technology Data Exchange (ETDEWEB)

KM3NeT is a future deep-sea research infrastructure hosting a neutrino telescope with a volume of at least one cubic kilometer to be constructed in the Mediterranean Sea. The experiment aims to detect high-energy cosmic neutrinos using a 3D array of optical modules to collect the Cherenkov light induced by charged particles in the water. Upward going muons and showers produced in neutrino interactions with the surrounding matter will allow the search and study of possible sources of extra-terrestrial neutrinos. The design of optical modules makes an important impact on the performance and cost of the KM3NeT project. Several different optical module configurations are under consideration; based on glass pressure spheres containing: a large (10 in.) hemispherical photomultiplier tube (with a multi-anode version as an option); 25-31 3 in. photomultiplier tubes, or a crystal scintillator-based hybrid device (X-HPD). The features and advantages of ...

2010-11-01

92

Modified 9Cr-1Mo steel shows excellent potential for steam generator applications  

Energy Technology Data Exchange (ETDEWEB)

A 9Cr-1Mo steel with properties improved over other ferritics in the ranges from 9 to 12% Cr and 1 to 2% Mo and over the widely used 2 1/2 Cr-1Mo steel has recently been developed. The main changes in the modified alloy, compared with the standard alloy, include: addition of niobium and vanadium, to improve the alloy's elevated-temperature strength properties; a specified range for each element; and a specification for nitrogen, which is not listed for the standard 9Cr-1Mo. Microstructural work has indicated that the improved strength of the modified alloy comes from two factors: (1) fine M/sub 23/C/sub 6/ precipitate particles nucleate on Nb/C, N, which comes out first during the heat treatment; and (2) the vanadium enters M/sub 23/C/sub 6/ and retards its growth at the service temperature. Mechanical properties discussed were Charpy-impact, tensile, and creep properties. Other properties included were: thermal expansion coefficient, ...

1982-12-01

93

High performance ultra-steels with recyclable design  

Energy Technology Data Exchange (ETDEWEB)

The global production of steel is predicted to increase rapidly to meet future demands. In order to conserve the natural resources, certain measures must be taken. These include perfecting the recycling of steel, improving the performance to extend the life of the material, and reduce the need for massive production of steel by increasing the strength of the material. This paper presented a design concept for ultrafine complex microstructure steel. The National Research Institute for Metals in Japan has worked on a project which investigated 800 MPa ferrite steel for welded structures with a chemical composition similar to 400 MPa-class plain carbon steel. The doubled strength was attributed to grain refinement. Novel welding techniques were also used for joining the ultrafine microstructure. In this study, low carbon Si-Mn ferrite-pearlite steels were subjected to a thermo-mechanical treatment to produce a microstructure of 1 micron order ultrafine grain ferrite plus finely dispersed ...

2000-07-01

94

Bimodality in binary Au + Au collisions from 60 to 100 MeV/u  

Energy Technology Data Exchange (ETDEWEB)

The deexcitation of quasi-projectiles (QP) released in binary Au on Au collisions as been studied from 60 to 100 MeV/u. Bimodality between two different decay patterns has been observed for intermediate violence collisions. The main experimental result is that the system jumps from one mode to the other on a narrow range of energy deposit and/or impact parameter. The sorting of the events (according to the violence of the collision) has been provided by the perpendicular energy of the light charged particles emitted on the quasi-target side. Such a sorting prevents spurious autocorrelation effects between the sorting variable and the observed mechanism. The two modes of the QP decay correspond on the one side to residue or fission fragments production, and on the other side to the multifragmentation channel. A detailed study has been performed in order to try to establish the origin of the observed bimodality in disentangling dynamical or ...

2003-03-01

95

Focused Ion Beam Recovery of Hypervelocity Impact Residue in Experimental Craters on Metallic Foils.  

Energy Technology Data Exchange (ETDEWEB)

The Stardust sample return capsule will return to Earth in January 2006 with primitive debris collected from Comet 81P/Wild-2 during the fly-by encounter in 2004. In addition to the cometary particles embedded in low-density silica aerogel, there will be microcraters preserved in the Al foils (1100 series; 100 {micro}m thick) that are wrapped around the sample tray assembly. Soda lime spheres ({approx}49 {micro}m in diameter) have been accelerated with a Light Gas Gun into flight-grade Al foils at 6.35 km s{sup -1} to simulate the capture of cometary debris. The experimental craters have been analyzed using scanning electron microscopy (SEM) and x-ray energy dispersive spectroscopy (EDX) to locate and characterize remnants of the projectile material remaining within the craters. In addition, ion beam induced secondary electron imaging has proven particularly useful in identifying areas within the craters that contain residue material. Finally, high-precision ...

2005-11-04

96

Multiscale modeling of skeletal muscle properties and experimental validations in isometric conditions.  

Science.gov (United States)

In this article, we describe an approach to model the electromechanical behavior of the skeletal muscle based on the Huxley formulation. We propose a model that complies with a well established macroscopic behavior of striated muscles where force-length, force-velocity, and Mirsky-Parmley properties are taken into account. These properties are introduced at the microscopic scale and related to a tentative explanation of the phenomena. The method used integrates behavior ranging from the microscopic to the macroscopic scale, and allows the computation of the dynamics of the output force and stiffness controlled by EMG or stimulation parameters. The model can thus be used to simulate and carry out research to develop control strategies using electrical stimulation in the context of rehabilitation. Finally, through animal experiments, we estimated model parameters using a Sigma Point Kalman Filtering technique and dedicated experimental protocols ...

2011-07-15

97

Macroscopic angular momentum states of Bose-Einstein condensates in toroidal traps  

International Nuclear Information System (INIS)

We consider a Bose-Einstein condensate (BEC) of N atoms of repulsive interaction #approx# U_0, in an elliptical trap, axially pierced by a Gaussian-intensity laser beam, forming an effective (quasi-2D) toroidal trap with minimum at radial distance #rho# = #rho#_p. The macroscopic angular momentum states #PSI#_l(#rho#,#theta#) #approx# #sq root#N#PHI#_l(#rho#)e"i"l"#theta# for integer l spread up to #rho# > #rho#_p. The spreading lowers rotational energies, so estimated low metastability barriers can support large l < or approx. l_m_a_x #approx# (NU_0)"1"/"4, < or approx. 10 for typical parameters. The l-dependent density profile module #PHI#_l(#rho#)"2 -#PHI#_0(#rho#)"2 is a signature of BEC rotation. Results are insensitive to off-axis laser displacements #rho#_0, for #rho#_0 #rho#_m_a_x << 1. (author).

98

Hydrogen-plasticity interactions in pearlitic steel: a fractographic and numerical study  

Energy Technology Data Exchange (ETDEWEB)

A fractographic and numerical approach is presented to analyze hydrogen-plasticity interactions in pearlitic steel and to elucidate the main hydrogen transport mechanism in this material under triaxial stress states produced by notches. Fractographic analysis showed that the microdamage produced by the hydrogen was clearly detectable by scanning electron microscopy (SEM), through a specific microscopic topography associated with hydrogen effects (tearing topography surface or TTS). Numerical computations obtained by using an elastic-plastic finite element program gave the progressive spreading of the plastic zone, closely associated with the movement of dislocations. In the majority of cases, the plastic zone (PZ) clearly exceeds the hydrogen affected region (TTS) and has no relation with it. In some tests, however, the hydrogen-induced micro-damage surpasses the only region in which there is dislocation movement, and in this case the net macroscopic transport of ...

1996-11-30

99

A study of kerf characteristics in abrasive waterjet machining of graphite/epoxy composite  

Energy Technology Data Exchange (ETDEWEB)

Kerf geometry, kerf wall features, and cutting front characteristics of an Abrasive Waterjet (AWJ) machined Graphite/Epoxy (Gr/Ep) laminate were studied. A macroscopic analyses suggests that geometrical features associated with AWJ machining of Gr/Ep laminates are influenced by three macro regions along the cutting depth. The presence of these regions, including initial damage at jet entry, smooth cutting, and rough cutting near the jet exit, depends on the operating conditions. Design of experiments and analysis of variance were used to determine the effect of cutting parameters on kerf characteristics and to develop empirical models for kerf profile and features of the three distinct macroscopic regions. Cutting front analysis revealed that the mechanisms of material removal in AWJ machining of Gr/Ep do not change over the jet penetration depth. In general, high quality uniform cuts may be obtained by minimizing initial damage at the jet ...

1996-04-01

100

Why we don`t need quantum planetary dynamics, or on decoherence and the correspondence principle for chaotic systems  

Energy Technology Data Exchange (ETDEWEB)

Violation of correspondence principle may occur for very macroscopic byt isolated quantum systems on rather short timescales as illustrated by the case of Hyperion, the chaotically tumbling moon of Saturn, for which quantum and classical predictions are expected to diverge on a timescale of approximately 20 years. Motivated by Hyperion, we review salient features of ``quantum chaos`` and show that decoherence is the essential ingredient of the classical limit, as it enables one to solve the apparent paradox caused by the breakdown of the correspondence principle for classically chaotic systems.

1995-08-01

101

Quantum Darwinism in quantum Brownian motion: the vacuum as a witness  

CERN Document Server

We study quantum Darwinism -- the redundant recording of information about a decohering system by its environment -- in zero-temperature quantum Brownian motion. An initially nonlocal quantum state leaves a record whose redundancy increases rapidly with its spatial extent. Significant delocalization (e.g., a Schroedinger's Cat state) causes high redundancy: many observers can measure the system's position without perturbing it. This explains the objective (i.e. classical) existence of einselected, decoherence-resistant pointer states of macroscopic objects.

2007-01-01

102

Periosteal Ewing's sarcoma  

International Nuclear Information System (INIS)

Periosteal Ewing's sarcoma is an uncommon, but well documented origin of this malignant condition with radiography signs, different from intramedullary growing tumours. Imaging modalities like CT or MRI supply proof of macroscopically intact endosteal cortical surface and free medullary cavity in long bones affected by this periosteal type of malignancy. Definite confirmation is valid after a careful microscopic investigation of the resected specimen. The prognosis of this type of Ewing's sarcoma may be favourable than that of the central type. Early diagnosis and therapy are thus essential. A clinical survey of six observations is given. (orig.).

103

Nuclear fuel behavior at an atomic scale: the contributions of the ab initio calculations and the synchrotron radiation; Comportement du combustible nucleaire a l'echelle atomique: les apports des calculs ab initio et du rayonnement synchrotron  

Energy Technology Data Exchange (ETDEWEB)

This paper presents fundamental researches based on the electronic structure calculations and X absorption spectroscopy, allowing the knowledge on nuclear fuels at an atomic scale. They bring a better understanding of these material behavior to accurate the macroscopic simulation. The calculation methods, the experimental techniques of validation and the ab initio calculations results are detailed. (A.L.B.)

2000-07-01

104

Nuclear Forensics' role in analyzing nuclear trafficking activities  

International Nuclear Information System (INIS)

Nuclear forensics aims at identifying origin and intended use of nuclear material using information inherent to the nuclear material.The information gathered in nuclear forensics include isotopic composition, elemental composition, impurities and age of the material, macroscopic appearance and microstructure. The information so collected helps to solve criminal cases and put the individuals involved in nuclear trafficking in jails. The information also helps to improve safeguards and physical protection measures at place of theft or diversion to prevent future thefts or diversions.

2010-05-10

105

Industrial processing of complex fluids: Formulation and modeling  

Energy Technology Data Exchange (ETDEWEB)

The production of many important commercial materials involves the evolution of a complex fluid through a cooling phase into a hardened product. Textile fibers, high-strength fibers(KEVLAR, VECTRAN), plastics, chopped-fiber compounds, and fiber optical cable are such materials. Industry desires to replace experiments with on-line, real time models of these processes. Solutions to the problems are not just a matter of technology transfer, but require a fundamental description and simulation of the processes. Goals of the project are to develop models that can be used to optimize macroscopic properties of the solid product, to identify sources of undesirable defects, and to seek boundary-temperature and flow-and-material controls to optimize desired properties.

1997-08-01

106

Graphitic nano tubes and aligned nano tubes films  

Energy Technology Data Exchange (ETDEWEB)

Carbon nano tubes are easily produced in macroscopic quantities, however their characterisation and possible applications are still rather limited. We have developed a new method to make aligned nano tube films which open new opportunities, not only for basic research but also for eventual applications. With this method the tubes can be aligned either parallel or perpendicular to the surface. We give a short review of the microscopic properties of single tubes and the bulk properties of the aligned films. (author). 24 refs., 6 figs.

1996-03-01

107

An influence of ion bombardment on plasma nitriding process of Ti6Al14V alloy at 843 K temperature  

International Nuclear Information System (INIS)

This work presents results of investigations on d.c. glow discharge nitriding of #alpha#+#beta# Ti-6Al-4V titanium alloy. The treatment was performed at 843 K in nitrogen-hydrogen atmosphere, pressure 300 Pa. Special attention was paid to nitriding mechanism and determination of the role of ion bombarding in nitriding process of titanium alloys. Produced as a result of d.c. plasma nitriding surface layers were subjected to macroscopic observations, microstructure studies, microhardness testing and X-ray analysis. (author)

2004-06-20

108

Trace element analysis and speciation for coal combustion systems using secondary ion mass spectrometry (SIMS) and particle induced x-ray emissions (PIXE)  

International Nuclear Information System (INIS)

Coal is the most abundant available fossil fuel in Australia and provides a substantial part of energy needs. It is used for power generation, to supply energy to industry as well as for domestic requirements. Analysis of trace elements (the elements present in coal in ppm/ppb level) during combustion of coal in very important. Trace elements, like heavy metals such as arsenic, selenium, and chromium etc. are hazardous to the environment and some of them have carcinogenic potency. In the near future more stringent limits may be proposed for such elements generated from combustion process, such as coal combustion in power plants. Hence analysis and assessment of the emissions of these elements is essential at this stage. The first step towards reducing any impacts of trace elements is to have accurate quantitative analysis. Analysis of coal, bottom ash and fly ash collected from five different power stations across Australia was carried out to study the quantity and ...

2005-11-20

109

A cryocondensation pump for the DIII-D Advanced Divertor Program  

Energy Technology Data Exchange (ETDEWEB)

A cryocondensation pump was designed for the baffle chamber of General Atomics DIII-D tokamak and will be installed in the fall of 1992. The purpose of the pump is to study plasma density control by pumping the divertor. The pump is toroidally continuous, approximately 10 m long and located in the lower outer corner of the vacuum chamber of the machine. It consists of a 1 m{sup 2} liquid helium-cooled surface surrounded by a liquid nitrogen-cooled shield to limit the heat load on the helium-cooled surface. The liquid nitrogen-cooled surface is surrounded by a radiation/particle shield to prevent energetic particles from impacting and releasing condensed water molecules. A thermal enhancement coating was applied to the nitrogen shell to lower the maximum temperature of the shell. The coating is non-continuous to keep the toroidal electrical resistance high. The whole pump is supported off the water-cooled vacuum vessel wall. ...

1992-03-01

115

Solid particle receiver experiments: velocity measurements  

Energy Technology Data Exchange (ETDEWEB)

Laser Doppler velocimetry and other photometric techniques are evaluated for measuring the average particle velocity in an ensemble of free-falling particles. The ability to obtain measurements in the presence of a radiant flux as high as 0.6 MW/m/sup 2/ was part of the evaluation. Optically dissimilar particles with diameters ranging from 0.1 mm to 1 mm were used in the study. Experimental results indicate that ensembles of particles do not behave as single isolated particles. The particle motion is dependent on particle volume fraction, and is quite unstable for falls greater than one meter.

1984-10-01

116

Solid particle receiver experiments: velocity measurements  

Science.gov (United States)

Laser Doppler velocimetry and other photometric techniques are evaluated for measuring the average particle velocity in an ensemble of free-falling particles. The ability to obtain measurements in the presence of a radiant flux as high as 0.6 MW/m/sup 2/ was part of the evaluation. Optically dissimilar particles with diameters ranging from 0.1 mm to 1 mm were used in the study. Experimental results indicate that ensembles of particles do not behave as single isolated particles. The particle motion is dependent on particle volume fraction, and is quite unstable for falls greater than one meter.

1984-10-01

117

Small world when building a particle detector prototype, the devil is in the tiny details  

CERN Multimedia

Small world when building a particle detector prototype, the devil is in the tiny details

2004-01-01

118

Particle-Sizing System for Scanning Electron Microscope ...  

Science.gov (United States)

... THESIS PARTICLE-SIZING SYSTEM FOR SCANNING ELECTRON MICROSCOPE IMAGES OF SOLID-PROPELLANT COMBUSTION EXHAUST ...

1991-03-01

119

Fragmentation of nuclei by particles and nuclei of intermediate and high energies  

Energy Technology Data Exchange (ETDEWEB)

The present state of investigations into the fragmentation of target nuclei by particles and nuclei of intermediate and high energies is reviewed.

1983-11-01

120

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

Energy Technology Data Exchange (ETDEWEB)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a {sup 137}Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 {+-} 0.9 cm{sup 2} y{sup -1}, is in good agreement with the values quoted by other workers on the ...

2010-11-15

121

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

International Nuclear Information System (INIS)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a "1"3"7Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 #+-# 0.9 cm"2 y"-"1, is in good agreement with the values quoted by other workers on the bioturbation ...

2010-11-01

122

Loss of light charged particles by nuclear interactions in BaF[sub 2] crystals  

Energy Technology Data Exchange (ETDEWEB)

The nuclear interaction probability of light charged particles in BaF[sub 2] crystals has been studied as a function of the incident particle energy. Light charged particles were identified in charge and mass by measuring their magnetic rigidity and their time-of-flight. The percentage of particles undergoing nuclear interactions has been measured for particles of charge from Z=1 to Z=6 and the experimental data are compared with the results of a model calculation. (orig.)

1993-07-15

123

Timber  

Science.gov (United States)

Nat'l Training Center Contact Us Directory Email Us BLM > Socioeconomic Impacts > Timber Print Page Socioeconomic Impacts from Timber BLM-administered lands yielded $337...

2011-09-24

124

Size Effects in Impact Damage of Composite Sandwich Panels Alan ...  

Science.gov (United States)

Wade. Jackson. - Army. VTD at NASA. Langley. ABSTRACT. Panel size has a large effect on the impact response and resultant damage level of honeycomb sandwich ...

125

Instrumeted Impact Testing of Composite Sandwich Panels,  

Science.gov (United States)

... Accession Number : ADD442819. Title : Instrumeted Impact Testing of Composite Sandwich Panels,. Corporate Author : AUBURN UNIV AL. ...

1989-05-01

126

Impacts of Renewable Fuel and Electricity Standards on State Economies (Poster)  

Energy Technology Data Exchange (ETDEWEB)

This poster, submitted for the CU Energy Initiative/NREL Symposium on October 3, discusses the impacts of renewable fuel and electricity standards on state economies.

2006-10-03

127

IMPACT OF INTERCONCEPTIONAL ANTIBIOTICS ON THE ENDOMETRIAL MICROBIAL FLORA  

UK PubMed Central (United Kingdom)

ObjectiveTo evaluate the impact of an interconceptional antibiotic regimen on the endometrial microbial flora and histology.Study DesignFull Text Available

2007-03-01

128

An Experimental Investigation of Sandwich Flat Panels Under ...  

Science.gov (United States)

... Figure 1.4. Low Velocity Impact 1-4 Page 25. Damage of composite sandwich panels caused by low velocity impact has been ...

1994-12-01

129

A Generic Impact-Scoring System Applied to Alien Mammals in Europe  

British Library Electronic Table of Contents (United Kingdom)

Abstract: We present a generic scoring system that compares the impact of alien species among members of large taxonomic groups. This scoring can be used to identify the most harmful alien species so that conservation measures to ameliorate their negative effects can be prioritized. For all alien mammals in Europe, we assessed impact reports as completely as possible. Impact was classified as either environmental or economic. We subdivided each of these categories into five subcategories (environmental: impact through competition, predation, hybridization, transmission of disease, and herbivory; economic: impact on agriculture, livestock, forestry, human health, and infrastructure). We assigned all impact reports to one of these 10 categories. All categories had impact scores that ranged f...

2010-01-01

130

Pipe whip studies  

Energy Technology Data Exchange (ETDEWEB)

An experimental and analytical study was performed to improve understanding of the dynamic impact behavior of carbon steel pipes. The test program addressed two types of pipe impact scenarios using both 2- and 4-in. Sch-80 pipes and elbows. Projectile-on-pipe tests simulated the behavior of a stationary target pipe which is impacted at its center by a larger, more rigid whipping pipe. These target pipes, which contained non-flowing water at about 290{degree}C temperature and ca 8.5 megapascals pressure, exhibited a peak deformation of up to 45% reduction in their diameter. For each test condition, the local deformation at the impact zone is a function of the peak impact force and impact velocity. Pipe-on-wall tests simulated the impact of an elbow at the free end of a cantilevered whipping pipe with a rigid barrier. The peak crush of the ...

1984-06-01

131

Formation of particles in combustion of biofuels  

International Nuclear Information System (INIS)

Biomass combustion is an important part in a sustainable energy system, but as well a source of submicron (particles < 1 #mu#m) particles in the air. Consequently, to obtain a good air quality together with increased biomass combustion there is a need for a better understanding of particle formation. This work is a part of a larger project about formation and emissions of particles from biofuel combustion. The report includes the work performed in the project during the year 2004. The aim of the project is to describe the release of inorganic components, which cause particle emissions, during combustion of single fuel particles of biofuel, e.g. wood pellets. The work is carried out by emission measurements, systematic combustion experiments and modelling work. The results are expected to contribute to the understanding of which parameters that influence the ...

132

X-RAY MICROANALYSIS OF A RADIOACTIVE PARTICLE WITH THE AID OF THE ELECTRON MICROSCOPE  

Science.gov (United States)

A radioactive particle was analyzed to discover the composition of the inactive material of the particle. The method uses the x-ray line spectrum of the K series caused by electron irradiation of the particle in the electron microscope. Iron and aluminum or silicon (the last two could not be distinguished) were found as inactive components in the particle. (D.L.C.)

1962-07-28

133

Method of removing entrained particles from flue gas and composition of matter  

Energy Technology Data Exchange (ETDEWEB)

A composition of matter to treat particles entrained in flue gas, is described comprising: a caustic liquid used to adjust resistivity of the entrained particles; and inert particulate matter supporting the caustic liquid for inhibiting chemical action of the caustic liquid until used to adjust the resistivity of the entrained particles, the inert particulate matter supporting sufficient caustic liquid to adjust the resistivity of the entrained particles.

1988-04-19

134

Metal nanoparticle inks  

Energy Technology Data Exchange (ETDEWEB)

Stabilized silver particles comprise particles comprising silver, a short-chain capping agent adsorbed on the particles, and a long-chain capping agent adsorbed on the particles. The short-chain capping agent is a first anionic polyelectrolyte having a molecular weight (Mw) of at most 10,000, and the long-chain capping agent is a second anionic polyelectrolyte having a molecular weight (Mw) of at least 25,000. The stabilized silver particles have a solid loading of metallic silver of at least 50 wt %.

2011-04-12

135

Magnetic flocculation and filtration  

Energy Technology Data Exchange (ETDEWEB)

A model is available in predicting flocculation frequencies between particles of various properties under the influence of a magnetic field. This model provides a basic understanding of fundamental phenomena, such as particle-particle and particle-collector interactions, occurring in HGMF (high gradient magnetic field), and will be extended to describe experimental data of particle flocculation and filtration and predict the performance of high- gradient magnetic filters. It is also expected that this model will eventually lead to a tool for design and optimization of magnetic filters for environmental, metallurgical, biochemical, and other applications.

1996-10-01

136

Continuous flow dielectrophoretic particle concentrator  

Energy Technology Data Exchange (ETDEWEB)

A continuous-flow filter/concentrator for separating and/or concentrating particles in a fluid is disclosed. The filter is a three-port device an inlet port, an filter port and a concentrate port. The filter separates particles into two streams by the ratio of their dielectrophoretic mobility to their electrokinetic, advective, or diffusive mobility if the dominant transport mechanism is electrokinesis, advection, or diffusion, respectively.Also disclosed is a device for separating and/or concentrating particles by dielectrophoretic trapping of the particles.

2007-04-17

137

gtz_eco_dokument_cd-rom  

Wastenet

to have a long-term impact on continuous improvement and national economic growth .

138

Working group report on electron-impact processes: Recommended database for electron impact excitation and ionization  

International Nuclear Information System (INIS)

The cross section database for electron impact excitation and electron impact ionization for hydrogen beam kinetic energies greater than 100 eV was considered, giving for each particular process a reference to a recommended publication of cross sections, as well as the accuracy or estimated accuracy. The work is motivated by the application of neutral beam injection in magnetic confinement devices, such as large tokamaks. 9 refs, 2 figs.

1989-07-01

145

Global Warming and California's Public Health  

Science.gov (United States)

This fact sheet summarizes the potential impact of climate change as it relates to public health in California....

146

Global Warming and California's Electricity Supply  

Science.gov (United States)

This fact sheet summarizes the potential impact of climate change as it relates to California's electricity supply. ...

147

Economic and Environmental Impact Assessment of Proposed Effluent Limitations Guidelines and Standards for the Coal Mining Industry: Remining and Western Alkaline Subcategories.  

Science.gov (United States)

Table of Contents: Executive Summary; Introduction; Data Sources; Industry Profile and Economic Baseline; Industry Compliance Costs; Industry Impacts; Additional Economic Impacts; Cost-Effectiveness; Environmental Impacts and Benefits; Social Costs and Be...

2000-01-01

148

Deforestation: Environmental impact and research needs  

Science.gov (United States)

The status of research on environmental problems that are produced by the phenomena of global deforestation is examined.

1983-01-01

151

Large eddy simulation of pulsating pool fire  

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: General simulation objectives of any fire analysis are macroscopic in nature and deals with the grass data in respect of fire/smoke spread, structural behaviour, environmental conditions etc. However, the accuracy of predicting such macroscopic parameters is a strong function of several other microscopic parameters which govern the overall macroscopic behaviour. Some of the microscopic parameters of interesting such analysis could be buoyancy induced stable/unstable flows, relative flame behaviour, baroclinic velocity distribution etc. Only the field based fire modelling approach is capable of calculating several of these by way of detailed CFD based field modelling. One of the best known tool that could be employed for such studies is the Fire Dynamics simulator (FDS) from NIST with its popular LES based fire modelling approach. Advanced LES based fire modelling scores over the ...

2005-07-01

152

Separation Phenomenon Occurring during the Charpy Impact Test of API X80 Pipeline Steels  

Science.gov (United States)

A separation phenomenon occurring during the Charpy impact test of API X80 pipeline steels was investigated in the present study. A detailed microstructural analysis of fractured impact specimens showed that the band structure of bainite elongated along the rolling direction worked as prior initiation sites for separations, and that the number and length of the separations increased with the increasing volume fraction of bainite. In the steels having high work hardenability, tearing-shaped separations were found because the hammer-impacted region was seriously hardened during the impact test, which led to the reduction in the impact toughness. As the test temperature decreased, the tendency toward separations increased, but separations were not found when the cleavage fracture prevailed at very low temperatures. These findings suggested that the formation of bainite and secondary ...

2009-10-01

153

Assessing the environmental impacts of resource recovery facilities  

Energy Technology Data Exchange (ETDEWEB)

Technologies and practices that recover energy and materials from municipal solid waste present a technically and economically viable alternative to sanitary landfills and other solid waste disposal methods. However, community planners considering resource recovery should be aware of the potential environmental impacts of proposed projects. To assess these impacts, a planner should: identify the most significant types of impacts; establish boundaries beyond which impacts are not significant; characterize the environment as it would exist without the proposed project over the project's lifetime; predict the magnitude, and the distribution over time and space, of potential impacts; and relate the magnitude of predicted impacts to a scale of significance that will allow environmental values to be considered in decision-making. 24 references, 1 table.

1980-03-01

154

U of C site vies for new particle accelerator  

CERN Multimedia

"American dominance in the study and development of high-energy particle physics may be seriously compromised, according to a report issued by the National Academy of Sciences, unless efforts are made to ensure that the next high-energy particle accelerator - the International Linear Collider (ILC) - will be constructed in the U.S.

2006-01-01

155

Search for free quarks at PEP  

Energy Technology Data Exchange (ETDEWEB)

The results of a search for fractionally charged particles produced in e/sup +/e/sup -/ annihilation at 29 GeV/c/sup 2/ are discussed. Results from cosmic-ray searches for fractionally charged particles, tachyons, and massive particles using the same detector are also presented.

1982-01-01

156

Particle creation if a cosmic string snaps  

CERN Document Server

We calculate the Bogolubov coefficients for a metric which describes the snapping of a cosmic string. If we insist on a matching condition for all times {\\it and} a particle interpretation, we find no particle creation.

1994-01-01

157

Entropic effects in channel-facilitated transport: Inter-particle interactions break the flux symmetry  

UK PubMed Central (United Kingdom)

We analyze transport through conical channels due to the difference in particle concentration on the two sides of the membrane. Because of the detailed balance, fluxes of non-interacting particles...Full Text Available

2009-08-01

158

Characterization of Two Unique Cholesterol-Rich Lipid Particles Isolated from Human Atherosclerotic Lesions  

UK PubMed Central (United Kingdom)

The authors' laboratory, using histochemicalmethods, previously identified two types of cholesterol-containing lipid particles in the extracellular spaces of human atherosclerotic lesions, one particle...Full Text Available

1990-01-01

159

A new method for quantifiable and controlled dosage of particulate matter for in vitro studies: the electrostatic particulate dosage and exposure system (EPDExS).  

Science.gov (United States)

An exposure chamber is described for the quantifiable addition of fine and ultrafine aerosol particulate matter directly to cells and used to demonstrate the in vitro cytotoxicity of fine 1,4-naphthoquinone particles to murine lung epithelial cells. The electrostatic particulate dosage and exposure system (EPDExS) operates on the principle of electrostatic precipitation and is shown to deposit fine and ultrafine aerosol particles directly to cells with 100% efficiency for particle diameters in the range of 40-530nm. This range is not limited by the EPDExS, but rather by the aerosolization method used for this study. Numbers of particles deposited onto the cells are counted with a condensation particle counter, negating any need to calculate or estimate particle exposure. The process of particle introduction, assessed using Trypan blue dye ...

2008-06-08

160

Wetting failure and contact line dynamics in a Couette flow  

CERN Document Server

Liquid-liquid wetting failure is investigated in a two-dimensional Couette system with two immiscible fluids of arbitrary viscosity. The problem is solved exactly using a sharp interface treatment of hydrodynamics (lubrication theory) as a function of the capillary number, viscous ratio and separation of scale, i.e. slip length versus macroscopic scale of the system. The existence of critical velocities, above which no stationary solutions are found, is analyzed in detail in terms of the relevant parameters of the system. Comparisons with existing analysis for other geometries are also carried out. A numerical method of analysis is also presented, based on diffuse interface models obtained from multiphase extensions of the lattice Boltzmann equation (LBE). Sharp interface and diffuse interface models are quantitatively compared face to face indicating the correct limit of applicability of the diffuse interface models.

2008-01-01

161

Time-resolved triple-axis spectroscopy - a new method for real-time neutron scattering  

International Nuclear Information System (INIS)

A new method for kinetic experiments with neutrons is described. This method combines the conventional triple-axis neutron spectroscopy with relaxation-type experiments. Whereas the former method yields information about the microscopic dynamics of solids, the latter provides macroscopic relaxation times. The combination of both methods allows to determine the microscopic mechanism of relaxation processes. The time-resolved triple-axis spectroscopy is limited to reversible processes and to time scales from 10"-"3 to 10"4 s. Typical applications are the kinetics of phase transformations (structural and dynamical changes), kinetics of domain distributions, kinetics of (spinodal) decomposition, reversible solid state reactions, time-dependent occupation of phonon states or phonon lifetimes. (orig.).

1990-04-01

162

Phase diagram and low temperature magnetization of Gdsub(x)Ysub(1-x)Rh_4B_4  

International Nuclear Information System (INIS)

The phase diagram of Gdsub(x)Ysub(1-x)Th_4B_4 between the paramagnetic, superconducting and ferromagnetic state is reported. Low temperature dc-magnetization measurements reveal that macroscopic electro-magnetic effects are of minor importance for the suppression of Hsub(2c), which shows a smooth bell-shaped behavior for x >= 0.15 with no indication of an anomaly near Tsub(c2). At low temperature in samples with x >= 0.20 a transition from type II to type I superconductivity seems to occur. The low temperature normal state susceptibility follows a Curie-Weiss law indicating reentrant behavior for x >= 0.10. (orig.).

1981-09-01

163

On the neutrino ball model  

Energy Technology Data Exchange (ETDEWEB)

It is suggested that the model of a neutrino ball described in terms of the standard model extended by adding right-handed neutrinos and the Majorana scalar field can be presented in order to explain a body of weak interacting neutrinos. Neutrino interaction with the scalar Majorana field violates the lepton number and produces the mass splitting of neutrino due to the sea-saw mechanism. In this model a neutrino ball is an object which appears as a result of a first order cosmological phase transition. It can be regarded as a ball filled with Dirac neutrinos and can be treated as a remnant of the phase transition with unbroken global lepton symmetry. In this paper we study the macroscopic parameters of such a configuration. In the result the mass-radius curve M(R) for this object is obtained. (orig.).

1995-07-01

164

Load transfer in bovine plexiform bone determined by synchrotron x-ray diffraction.  

Energy Technology Data Exchange (ETDEWEB)

High-energy synchrotron x-ray diffraction (XRD) has been used to quantify load transfer in bovine plexiform bone. By using both wide-angle and small-angle XRD, strains in the mineral as well as the collagen phase of bone were measured as a function of applied compressive stress. We suggest that a greater proportion of the load is borne by the more mineralized woven bone than the lamellar bone as the applied stress increases. With a further increase in stress, load is shed back to the lamellar regions until macroscopic failure occurs. The reported data fit well with reported mechanisms of microdamage accumulation in bovine plexiform bone.

2008-02-01

165

Inelastic proton scattering as a mean for the determination of neutron and proton matrix element ratios  

Energy Technology Data Exchange (ETDEWEB)

The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0{sup +}{yields}2{sup +} transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: {sup 18}O, {sup 30}Si, {sup 32,34}S, {sup 48}Ca, {sup 88}Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.

1999-12-06

166

Inelastic proton scattering as a mean for the determination of neutron and proton matrix element ratios  

International Nuclear Information System (INIS)

The determination of ratio of neutron over proton matrix elements by inelastic proton scattering, for 0"+#->#2"+ transitions, is investigated via the comparison between experimental data and theoretical calculations. Calculations into the context of a macroscopic and a microscopic description are performed for a wide mass range nuclei: "1"8O, "3"0Si, "3"2","3"4S, "4"8Ca, "8"8Sr, for which these ratios were determined previously with an independent technique. At that point the choice of the theoretical model may be very critical. It is thus the purpose of this investigation to point out the most suitable model. It is found that in general both theoretical models can be employed for the reliable determination of neutron over proton matrix element ratios.

1999-12-06

167

Improvements on burnup chain model and group cross section library in the SRAC system  

Energy Technology Data Exchange (ETDEWEB)

Data and functions of the cell burnup calculation of the SRAC system were revised to improve mainly the accuracy of the burnup calculation of high conversion light water reactors (HCLWRs). New burnup chain models were developed in order to treat fission products (FPs) and actinide nuclides in detail. Group cross section library, SRACLIB-JENDL2, was generated based on JENDL-2 nuclear data file. In generating this library, emphasis was placed on FPs and actinides. Also revised were the data such as the average energy release per fission for various actinides. These improved data were verified by performing the burnup analysis of PWR spent fuels. Some new functions were added to the SRAC system for the convenience to yield macroscopic cross sections used in the core burnup process. (author).

1992-01-01

168

Importance of the Adrenal Gland Blood Supply During Laparoscopic Subtotal Adrenalectomy  

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction: Laparoscopic subtotal adrenalectomy (LSA) has emerged as a treatment option in the management of certain adrenal pathologies. After LSA, a satisfactory blood supply to the adrenal remnant is vital to preserve steroid function. The aim of this study was to review the adrenal blood supply with relevance to LSA. Materials and Methods: The adrenal blood supply was examined in three ways: 1) a review of six previous cadaver studies looking at adrenal blood supply; 2) a review of our 164 consecutive laparoscopic adrenalectomies (LAs) (January 1999?January 2009); the details of the main adrenal veins and variants had been prospectively recorded; and 3) dissection of 4 cadaver specimens (macroscopic and histologic examination was performed). Results: The six cadaver studies ...

2010-01-01

169

High temperature structural silicides  

Energy Technology Data Exchange (ETDEWEB)

Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi{sub 2}-based materials, which are borderline ceramic-intermetallic compounds. MoSi{sub 2} single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi{sub 2} possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi{sub 2}-Si{sub 3}N{sub 4} composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi{sub 2}-based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing.

1997-03-01

170

Expression of suppressor of cytokine signaling 1 and 3 in ligature-induced periodontitis in rats  

British Library Electronic Table of Contents (United Kingdom)

Objective: : Evaluate expression of inducible negative regulators of JAK/STAT pathway and their target proteins during the course of ligature-induced experimental periodontal disease in rats. Design: : Rats were sacrificed 07, 15 and 30days after disease induction for histological evaluation of periodontal inflammation and macroscopic analysis of alveolar bone loss. SOCS expression and the activation status of STAT1 and STAT3 were evaluated in gingival biopsies by real time PCR and Western blot. Results: : Ligature-induced model presented significant progressive bone loss from 7 to 30days. Inflammation was evident and similar for 07 and 15days; however, a decrease on severity at the end of the experimental period was observed. There was a significant (p<0.05) increase on SOCS1 and SOCS3 ge...

2011-01-01

171

Experiments on determination of damage effect ions "2"2Ne (172 MeV) on UO_2 monocrystals  

International Nuclear Information System (INIS)

Shadow effect was used for investigating damage of uranium dioxide monocrystal. The dependence of shadow minimum parameters on fluence of "2"2Ne ions with 172 MeV energy was followed when detecting fission fragments. Ion dose responsible for sufficient microdamage of lattice structure, included into the classification of heavy ion damage effect on monocrystals was determined. The problem of radiation intensity effect on the character of occurred damages was studied. It was established that macroscopic sample failure, caused by generation of considerable mechanical stresses in monocrystal under beam effect could be observed along with microdamages of lattice structure at ion flux density >10"1"2 cm"-"2Xs"-"1.

172

Effects of the alfven wave spectrum in heating experiments in TCA  

International Nuclear Information System (INIS)

Reduction of the metallic impurity concentration in the TCA plasma has enabled us to correlate the observed heating with the calculated position where the rf energy is deposited. In modelling the measured antenna loading due to the presence of Alfven resonance surfaces, and hence inferring the energy deposition profile, both ion cyclotron effects and the toroidal geometry must be considered. In particular, toroidicity couples energy to resonance surfaces that would not be excited in cylindrical geometry. The increase in electron density during a rf pulse changes the positions of these surfaces so that spectrum-related effects may be observed. The appearance of a new surface at the centre of the plasma is seen as a sharp discontinuity on many of the macroscopic parameters, accompanied by evidence of changes in the current density profile. These results, and the predictions of numerical codes, have imposed new constraints on the optimisation of our antenna system.

173

Development of large scale parallel visco-elastic analysis system with mesoscopic material model  

International Nuclear Information System (INIS)

We develop a large scale parallel viscous-elastic analysis program incorporating a mesoscopic self-consistent model developed by Laws. In the model, macroscopic elastic constants are treated as variables depending on the shape and statistical properties of pre-existing microscopic pores and change due to neutron irradiation. We apply this program to the visco-elastic analysis of nuclear graphite structures under neutron irradiation environment in High Temperature Gas-cooled Reactor (HTGR), as an example problem. Furthermore the calculated results by this parallel computational program are compared with those by one of commercial finite element analysis codes, FINAS, for validating elastic and thermal stress analysis function. (author)

2000-09-01

174

Degradation Improves Tissue Formation in (Un)Loaded Chondrocyte-laden Hydrogels  

British Library Electronic Table of Contents (United Kingdom)

Background Photopolymerizable poly(ethylene glycol) (PEG) hydrogels offer a platform to deliver cells in vivo and support three-dimensional cell culture but should be designed to degrade in sync with neotissue development and endure the physiologic environment. Questions/purposes We asked whether (1) incorporation of degradation into PEG hydrogels facilitates tissue development comprised of essential cartilage macromolecules; (2) with early loading before pericellular matrix formation, the duration of load affects matrix production; and (3) dynamic loading in general influences macroscopic tissue development. Methods Primary bovine chondrocytes were encapsulated in hydrogels (n?=?3 for each condition). The independent variables were hydrogel degradation (nondegrading PEG and degrading olig...

2011-01-01

175

Benign lymphoepithelial lesion of the parotid gland in AIDS patients: CT characteristics  

International Nuclear Information System (INIS)

Contrast agent-enhanced CT scans in nine male patients with histologically proved benign lymphoepithelial lesions of the perotid gland were reviewed. All scans showed cystic-appearing masses with peripheral rim enhancement corresponding to the macroscopic appearance of the lesion. Five patients were seropositive for human immunodeficiency virus (HIV) infection or had infections seen in acquired immunodeficiency syndrome. Three patients were members of high-risk groups. Only one patient had symptoms of the SICCA syndrome. Once a rare cause of parotid gland enlargement, benign lymphoepithelial lesions have recently been seen with increasing frequency in patients with HIV infection. Although the CT appearance is not pathognomic, correlation results of aspiration cytology and with clinical history can lead to a preoperative diagnosis of a benign lymphoepithelial lesion.

176

Atomic scale simulations of arsenic ion implantation and annealing in silicon  

International Nuclear Information System (INIS)

We present results of multiple-time-scale simulations of 5, 10 and 15 keV low temperature ion implantation of arsenic on silicon (100), followed by high temperature anneals. The simulations start with a molecular dynamics (MD) calculation of the primary state of damage after 10ps. The results are then coupled to a kinetic Monte Carlo (MC) simulation of bulk defect diffusion and clustering. Dose accumulation is achieved considering that at low temperatures the damage produced in the lattice is stable. After the desired dose is accumulated, the system is annealed at 800 degrees C for several seconds. The results provide information on the evolution for the damage microstructure over macroscopic length and time scales and affords direct comparison to experimental results. We discuss the database of inputs to the MC model and how it affects the diffusion process.

2004-12-15

177

Asymmetrical mechanical behavior of a precipitation hardened beta titanium alloy  

International Nuclear Information System (INIS)

Precipitation-hardened single crystals of a beta (bcc) Ti--40 at. percent V--1.0 at. percent Si alloy were deformed in compression at 77 and 298"0K. The dependence of the yield stress upon aging time at 843"0K for solution-treated crystals shows two maxima which are caused by silicide precipitates. The orientation dependence of the yield stress and of the active macroscopic slip plane were determined as a function of aging time. The solution-treated as well as aged crystals exhibit an asymmetry of both the yield stress and the plane of slip, the degree of asymmetry being larger at 77 than at 298"0K. The asymmetry of slip and yielding is not affected by the presence of precipitation hardening. Results indicate that the effect of the dislocation core structure on dislocation motion is independent of the presence of precipitates. (auth).

178

A phenomenological model for the macroscopic characteristics of irradiated silicon  

International Nuclear Information System (INIS)

The dependence of the carrier concentrations, of the resistivity and of the Hall coefficient of irradiated silicon on the neutron fluences has been investigated, starting from the supposition that the main phenomena induced by irradiation in the semiconductor bulk are shallow-donor removal and deep-centres creation. The free parameters of the model are initial doping of the starting material, the permitted energy level values of the radiation-induced centres in the semiconductor band gap and their introduction rates. The influence of each parameter on the calculated dependences is studied in detail, for three cases: one deep acceptor-like centre, two deep acceptors and one deep acceptor plus one deep donor-like centre. each of the three cases is discussed in correspondence with different experimental results.

179

A Subchronic Intravenous Toxicity Study of Magnesium Fructose-1,6-Diphosphate in Beagle Dogs  

British Library Electronic Table of Contents (United Kingdom)

Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...

2009-01-01

180

Wear particle equilibrium measurements and their significance  

Energy Technology Data Exchange (ETDEWEB)

Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.

1980-11-01

181

Thermal performance and design of a solid particle cavity receiver  

Energy Technology Data Exchange (ETDEWEB)

A model for energy transport in a solid particle cavity receiver is developed and applied to the design and analysis of a receiver for the Central Receiver Test Facility (CRTF), Albuquerque, New Mexico. The model gives thermal performance results - including particle temperatures, cavity efficiencies, and wall temperatures - which directly affect the economic and technical feasibility of a solid particle receiver. In addition, design criteria relevant to the configuration of a solid particle cavity receiver are developed. Results for CRTF indicate that at design conditions particle temperatures will exceed 1200/sup 0/K with cavity efficiencies on the order of 75%.

1985-04-01

182

UARS Particle Environment Monitor (PEM) Level 3AT - Mirador - NASA  

Science.gov (United States)

May 11, 2011 ... The Particle Environment Monitor (PEM) on NASA's Upper Atmosphere Research Satellite (UARS) measures the type, amount, energy, and ...

185

Smooth Particle Hydrodynamics for Surf Zone Waves  

Science.gov (United States)

... Zou, S. and RA Dalrymple, ``Coastal Sediment Transport Simulation by Smoothed Particle Hydrodynamics,'' Journal of Waterways, Ports, Coastal ...

2011-05-15

186

Non-equilibrium particle emission in 45 MeV #alpha# particle bombardment of "1"5"9Tb  

International Nuclear Information System (INIS)

Mar 1982. p. 36-37. Germany Didelez, JP Paris-11 Univ., 91 - Orsay (France).

1982-03-01

187

Monosodium titanate particle characterization  

Energy Technology Data Exchange (ETDEWEB)

A characterization study was performed on monosodium titanate (MST) particles to determine the effect of high shear forces expected from the In-Tank Precipitation (ITP) process pumps on the particle size distribution. The particles were characterized using particle size analysis and scanning electron microscopy (SEM). No significant changes in particle size distributions were observed between as-received MST and after 2--4 hours of shearing. Both as-received and sheared MST particles contained a large percentage of porosity with pore sizes on the order of 500 to 2,000 Angstroms. Because of the large percentage of porosity, the overall surface area of the MST is dominated by the internal surfaces. The uranium and plutonium species present in the waste solution will have access to both interior and exterior surfaces. Therefore, uranium and plutonium loading should ...

1993-01-12

188

Mechanical properties of surface composite particles coated with finer particles; Hyomen hifukugata fukuto biryushiso no rikigaku tokusei  

Energy Technology Data Exchange (ETDEWEB)

The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise ...

1996-05-10

189

Experts worry US may lose leadership in particle physics  

CERN Multimedia

"Physics in the United States is in a crisis that the country may lose the leadership in basic particle research in coming years, a report of the National Research Council warned." (1 page)

2006-01-01

190

Airborne minerals and related aerosol particles: Effects on climate and the environment  

UK PubMed Central (United Kingdom)

Aerosol particles are ubiquitous in the troposphere and exert an important influence on global climate and the environment. They affect climate through scattering, transmission, and absorption of...Full Text Available

1999-03-30

191

lightsources.org: An Internet Site for Light SourceCommunication  

Energy Technology Data Exchange (ETDEWEB)

Research at the world's accelerator- (storage-ring and linac) based light sources is one of the most dynamic and rapidly growing fields of science. It frequently results in direct benefits to society, thereby demonstrating the value of the research with very concrete examples, but this is not widely understood or appreciated outside of the immediate user community. Our growing group of light source communicators from facilities in Europe, Asia, and the Americas, inspired by the Interactions.org Web site created by high-energy (elementary-particle)physics communicators, concluded that a light source community Web site (lightsources.org) would be the best tool for establishing effective collaboration between the communications offices of the world's light sources and to maximize the impact of our efforts. We envision lightsources.org to serve as a one-stop-shopping site for information about all aspects of light sources and the ...

2004-10-04

192

Understanding and predicting soot generation in turbulent non-premixed jet flames.  

Energy Technology Data Exchange (ETDEWEB)

This report documents the results of a project funded by DoD's Strategic Environmental Research and Development Program (SERDP) on the science behind development of predictive models for soot emission from gas turbine engines. Measurements of soot formation were performed in laminar flat premixed flames and turbulent non-premixed jet flames at 1 atm pressure and in turbulent liquid spray flames under representative conditions for takeoff in a gas turbine engine. The laminar flames and open jet flames used both ethylene and a prevaporized JP-8 surrogate fuel composed of n-dodecane and m-xylene. The pressurized turbulent jet flame measurements used the JP-8 surrogate fuel and compared its combustion and sooting characteristics to a world-average JP-8 fuel sample. The pressurized jet flame measurements demonstrated that the surrogate was representative of JP-8, with a somewhat higher tendency to soot formation. The premixed flame measurements revealed that flame temperature has a ...

2010-10-01

193

Technical description of parameters influencing the pH value of suspension absorbent used in flue gas desulfurization systems.  

Science.gov (United States)

As a result of the large limestone deposits available in Poland, the low cost of reagent acquisition for the largescale technological use and relatively well-documented processes of flue gas desulfurization (FGD) technologies based on limestone sorbent slurry, wet scrubbing desulfurization is a method of choice in Poland for flue gas treatment in energy production facilities, including power plants and industrial systems. The efficiency of FGD using the above method depends on several technological and kinetic parameters, particularly on the pH value of the sorbent (i.e., ground limestone suspended in water). Consequently, many studies in Poland and abroad address the impact of various parameters on the pH value of the sorbent suspension, such as the average diameter of sorbent particles (related to the limestone pulverization degree), sorbent quality (in terms of pure calcium carbonate [CaCO3] content of the sorbent material), stoichiometric ...

2010-08-01

194

Study of scalar leptons at the TESLA Photon Collider  

International Nuclear Information System (INIS)

In this thesis, the potential to discover supersymmetric signatures in both e"+e"- and #gamma##gamma# colliders evaluated with a Monte Carlo analysis, is discussed. The analysis was focused on the detection of muons, essentially. First, we study the detection of #mu#"+_R#mu#"-_R in e"-e"+ collisions, whose purpose is the measurement of the #mu#_R mass. It was found that an uncertainty of 0.11 GeV (stat) can be achieved. Under the assumption of the real conditions of the ILC photon collider, a study covering the detection of #mu#"+_R#mu#"-_R and #mu#"+_L#mu#"-_L pairs for #sq root#(s_e_"-_e_"+)=0.5 and 0.6 TeV was performed. According to the simulation, a statistical error for the branching ratios of #mu#"#+-#_L#->##chi#"0_1#mu#"#+-# of 0.98% and #mu#"#+-#_L#->##chi#"0_2#mu#"#+-# of 3.97% can be reached. In order to judge the Monte Carlo results, we have used a technique based on a multidimensional fit to evaluate the impact of the branching ratio measurements ...

195

On the relation between morphology and elastic properties in amorphous columnar thin films  

International Nuclear Information System (INIS)

The optical, electromagnetic and mechanical properties of thin films (TFs) are directly correlated to their morphology at the nanoscale. This, in concert with the fact that new deposition techniques are enabling the growth of thin films with very complex morphologies, there is an increasing interest in model-based simulation (MBS) for the design of engineering structures (including nanostructures), and increasing computer speeds are beginning to make MBS an effective design tool capable of bridging the nanoscale with the continuum scale, has made it increasingly important to understand how the nanostructure of a thin film impacts its properties at all length scales. The authors have developed the capability to determine the mechanical properties of thin films with amorphous nanostructure by combining molecular dynamics, i.e., position of particles (e.g., atoms or molecules) and their interatomic potential(s), with continuum mechanics ...

2002-07-07

196

NATURAL GAS VARIABILITY IN CALIFORNIA: ENVIRONMENTAL IMPACTS AND DEVICE PERFORMANCE EXPERIMENTAL EVALUATION OF POLLUTANT EMISSIONS FROM RESIDENTIAL APPLIANCES  

Science.gov (United States)

The effect of liquefied natural gas on pollutant emissions was evaluated experimentally with used and new appliances in the laboratory and with appliances installed in residences, targeting information gaps from previous studies. Burner selection targeted available technologies that are projected to comprise the majority of installed appliances over the next decade. Experiments were conducted on 13 cooktop sets, 12 ovens, 5 broiler burners, 5 storage water heaters, 4 forced air furnaces, 1 wall furnace, and 6 tankless water heaters. Air-free concentrations and fuel-based emission factors were determined for carbon monoxide, nitrogen oxides, nitrogen dioxide, and the number of (predominantly ultrafine) particles over complete burns?including transient effects (device warm-up and intermittent firing of burners) following ignition--and during more stable end-of-burn conditions. Formaldehyde was measured over multi-burn cycles. The baseline fuel was Northern California ...

2009-12-01

197

Fundamentals of focused ion beam nanostructural processing: below,at and above the surface  

Energy Technology Data Exchange (ETDEWEB)

This article considers the fundamentals of what happens in asolid when it is impacted with a medium energy gallium ion. The study ofthe ion/sample interaction at the nanometer scale is applicable to mostfocused ion beam (FIB) based work even if the FIB/sample interaction isonly a step in the process, e.g., micromachining or microelectronicdevice processing. Whereas the objective in other articles in this issueis to use the FIB tool to characterize a material or to machine a deviceor transmission electron microscopy (TEM) sample, the goal of the FIB inthis article is to have the FIB/sample interaction itself become theproduct. To that end, the FIB/sample interaction is considered in threecategories according to geometry: below, at, and above the surface.First, the FIB ions can penetrate the top atom layer(s) and interactbelow the surface. Ion implantation and ion damage on flat surfaces havebeen comprehensively examined; however, FIB applications require thefurther ...

2007-03-30

198

Adsorption of ethylene on graphitized thermal carbon black and in slit pores: a computer simulation study.  

Science.gov (United States)

In this paper, we studied vapor-liquid equilibria (VLE) and adsorption of ethylene on graphitized thermal carbon black and in slit pores whose walls are composed of graphene layers. Simple models of a one-center Lennard-Jones (LJ) potential and a two-center united atom (UA)-LJ potential are investigated to study the impact of the choice of potential models in the description of VLE and adsorption behavior. Here, we used a Monte Carlo simulation method with grand canonical Monte Carlo (GCMC) and Gibbs ensemble Monte Carlo ensembles. The one-center potential model cannot describe adequately the VLE over the practical range of temperature from the triple point to the critical point. On the other hand, the two-center potential model (Wick et al. J. Phys. Chem. B 2000, 104, 8008-8016) performs well in the description of VLE (saturated vapor and liquid densities and vapor pressure) over the wide range of temperature. This UA-LJ model is then used in the study of ...

2004-08-17

199

High resolution alpha-particle spectroscopy using CR-39 plastic track detector  

Energy Technology Data Exchange (ETDEWEB)

A technique has been developed for high resolution alpha particle spectroscopy from track length determination in CR-39 plastic. On individual tracks an energy resolution deltaE close to the range straggling limit is obtainable. For 6 MeV alpha-particle deltaE is proportional 35 keV on individual particles and for groups of particles deltaE proportional 20 keV can be achieved using certain data selection criteria. At 100 keV on individual particles deltaE is proportional 20 keV. The analysis requires 1) a knowledge of the track-etch rate (Vsub(T))-range relationship and 2) a theoretical understanding of alpha-particle track structure in CR-39 as a function of particle energy, dip angle and degree of etching. The structure of alpha-particle etched tracks in CR-39 is described and two methods of analysis discussed. ...

1984-06-15

200

Implementation Plan. Environmental Restoration and Waste Management Programmatic Environmental Impact Statement  

Energy Technology Data Exchange (ETDEWEB)

In accordance with the Department of Energy`s National Environmental Policy Act implementing procedures in Volume 10 of the Code of Federal Regulations, Section 1021,312, the Environmental Restoration and Waste Management Programmatic Environmental Impact Statement Implementation Plan has two primary purposes: to provide guidance for the preparation of the Programmatic Environmental Impact Statement and to record the issues resulting from the scoping and the extended public participation process. The Implementation Plan identifies and discusses the following: background of Environmental Restoration and Waste Management activities, the purpose of the Programmatic Environmental Impact Statement, and the relationship of the Programmatic Environmental Impact Statement to other Departmental initiatives (Chapter 1); need and purposes for action (Chapter 2); scoping process and results of the public ...

1994-01-01

201

Experimental studies of pipe whip and impact: Final report  

Energy Technology Data Exchange (ETDEWEB)

An experimental and computational study was undertaken to estimate the effects of pipe rupture and induced pipe whip impact on surround structures considered either as rigid or deformative such as concrete slabs. This program included sixteen tests using 3 inch schedule 80 (or 10) pipes made of carbon steel similar to A106 grade B. The study consisted of tests on rigid target and on concrete slab. The investigation of whip phase and impact phase was done separately for each test. For pipe impact on rigid targets, the impact forces are found to be directly related to the crush strength of the pipe and the general pipe deformation following the impact. For pipe impact on concrete slabs, the response of the target to the pipe impact needs to take into account the local effect such as penetration and localized damage on the slab. The test matrix ...

1987-02-01

202

Ultra-fast charge transfer in organic electronic materials and at hybrid interfaces studied using the core-hole clock technique  

Energy Technology Data Exchange (ETDEWEB)

Research highlights: {yields} The use of resonant photoemission in its 'core-hole clock' expression for the study of the dynamical charge transfer across hybrid organic-inorganic interfaces and for the intermolecular charge transfer in the bulk of organic thin films is reviewed. {yields} The electronic coupling to the substrate and the efficiency of charge transport across hybrid interfaces is different for individual electronic subsystems of the molecular adsorbate. {yields} The intermolecular charge transfer in the bulk of discotic liquid crystals occurs on the order of a few femtoseconds and is faster than expected from the macroscopic charge transport characteristics of the material. -- Abstract: The focus of this brief review is the use of resonant photoemission in its 'core-hole clock' expression for the study of two important problems relevant for the field of organic electronics: the dynamical charge transfer across ...

2011-01-15

203

Tumour control probability (TCP) for non-uniform activity distribution in radionuclide therapy  

Energy Technology Data Exchange (ETDEWEB)

Non-uniform radionuclide distribution in tumours will lead to a non-uniform absorbed dose. The aim of this study was to investigate how tumour control probability (TCP) depends on the radionuclide distribution in the tumour, both macroscopically and at the subcellular level. The absorbed dose in the cell nuclei of tumours was calculated for {sup 90}Y, {sup 177}Lu, {sup 103m}Rh and {sup 211}At. The radionuclides were uniformly distributed within the subcellular compartment and they were uniformly, normally or log-normally distributed among the cells in the tumour. When all cells contain the same amount of activity, the cumulated activities required for TCP = 0.99 (A-tilde{sub TCP=0.99}) were 1.5-2 and 2-3 times higher when the activity was distributed on the cell membrane compared to in the cell nucleus for {sup 103m}Rh and {sup 211}At, respectively. TCP for {sup 90}Y was not affected by different radionuclide distributions, whereas for {sup 177}Lu, it was slightly ...

2008-08-21

204

Numerical investigation of boiling regime transition mechanism by a Lattice-Boltzmann model  

Energy Technology Data Exchange (ETDEWEB)

A numerical study has been performed to investigate the hydrodynamic aspects of the pool boiling on horizontal-, vertical- and downward-facing surfaces. The FlowLab code, which is based on a Lattice-Boltzmann (LB) model of two-phase flows, is employed. Macroscopic properties, such as surface tension ({sigma}) and contact angle ({beta}), are implemented through the fluid-fluid (G{sub {sigma}}) and fluid-solid (G{sub t}) interaction potentials. The model is found to express a linear relation between the macroscopic properties ({sigma}, {beta}) and microscopic parameters (G{sub {sigma}}, G{sub t}). The simulation results on bubble departure diameter appear to have the same parametric dependence as the empirical correlation. Hydrodynamic aspects of two-phase flow regime transition mechanism are investigated for different surface-coolant configurations. Results of the LB simulation clearly demonstrate that not only the bubble nucleation site density ...

2001-02-01

205

Multiscale modeling of transdermal drug delivery  

Science.gov (United States)

This study addresses the modeling of transdermal diffusion of drugs, to better understand the permeation of molecules through the skin, and especially the stratum corneum, which forms the main permeation barrier of the skin. In transdermal delivery of systemic drugs, the drugs diffuse from a patch placed on the skin through the epidermis to the underlying blood vessels. The epidermis is the outermost layer of the skin and can be further divided into the stratum corneum (SC) and the viable epidermis layers. The SC consists of keratinous cells (corneocytes) embedded in the lipid multi-bilayers of the intercellular space. It is widely accepted that the barrier properties of the skin mostly arises from the ordered structure of the lipid bilayers. The diffusion path, at least for lipophilic molecules, seems to be mainly through the lipid bilayers. Despite the advantages of transdermal drug delivery compared to other drug delivery routes such as oral dosing and injections, the low ...

2006-01-01

206

Linking ab initio energetics to experiment: kinetic Monte Carlo simulation of transient enhanced diffusion of B in Si  

Energy Technology Data Exchange (ETDEWEB)

We have developed a kinetic Monte Carlo (kMC) simulator that links atomic migration and binding energies determined primarily from first principles calculations to macroscopic phenomena and laboratory time scales. Input for the kMC simulation is obtained from a combination of ab initio planewave pseudopotential calculations, molecular dynamics simulations, and experimental data. The simulator is validated against an extensive series of experimental studies of the diffusion of B spikes in self-implanted Si. The implant energy, dose, and dose rate, as well as the detailed thermal history of the sample, are included. Good agreement is obtained with the experimental data for temperatures between 750 and 950 C and times from 15 to 255 s. At 1050o C we predict too little diffusion after 105 s compared to experiment: apparently, some mechanism which is not adequately represented by our model becomes important at this temperature. Below 1050o C, the kMC simulation produces ...

1998-12-16

207

Impact properties of low alloy TRIP steels; Teigokin TRIP ko no shogeki tokusei  

Energy Technology Data Exchange (ETDEWEB)

The impact properties of high-strength low alloy TRIP steels such as 'TRIP-aided dual-phase steel' and 'TRIP-aided bainitic steel' associated with the transformation-induced plasticity (TRIP) of retained austenite were investigated for some applications to the automotive impact members. The TRIP steels possessed far higher impact absorbed value and lower ductile-brittle transition temperature than the conventional ferrite-martensite and ferrite-pearlite steels. The stress relaxation resulting from the strain-induced transformation of retained austenite islands or films improved the impact properties in terms of suppressing void and/or crack initiation and these propagation. The best impact properties were completed in the steel composing of uniform fine bainitic lath structure and a large amount of stable interlath retained austenite films. ...

2000-08-01

208

Economic impact analysis for proposed effluent limitations guidelines and standards for the coastal subcategory of the oil and gas extraction point source category  

Science.gov (United States)

This economic impact analysis (EIA) examines compliance costs and economic impacts resulting from the U.S. Environmental Protection Agency`s (EPA`s) proposed revisions to effluent limitations guidelines and standards for the Coastal Subcategory of the U.S. oil and gas industry. The EIA estimates economic impacts in terms of annualized costs; production losses; and changes in equity, working capital, and other indicators of financial health at the firm level. In addition, impacts on employment and affected communities, foreign trade, and new sources are considered. A Regulatory Flexibility Analysis detailing the impacts on small businesses within the coastal oil and gas industry also is included in the EIA.

1995-01-01

209

Application of high velocity impact welding at varied different length scales  

British Library Electronic Table of Contents (United Kingdom)

Three complementary impact welding technologies are described in this paper. They are explosive welding, magnetic pulse welding, and laser impact welding, which have been used to provide metallurgical bonds between both similar and dissimilar metal pairs. They share the physical principle that general impact-driven welding can be carried out by oblique impact but are used at different length scales from meters to sub-millimeter. The different length scales require different kinds of systems to drive the process, and the scales themselves can give different weld morphologies. Metallographic analysis on cross-sections shows a wavy interface morphology which is likely the result of an instability associated with jetting, which scours the surfaces clean during impact. The normalized period and...

2011-01-01

210

Test of superconducting Nb/Al bilayers as particle detectors  

Energy Technology Data Exchange (ETDEWEB)

Superconducting thin film particle detectors can be very attractive due to the low sensitivity to radiation damage. We describe the fabrication procedure and the characterization of Nb/Al bilayers as particle detectors. First steady and dynamical results are reported from tests of 5 MeV alpha-particle detection.

2000-04-07

211

Tachyons: may they have a role in elementary particle physics  

International Nuclear Information System (INIS)

The possible role of space-like objects in elementary particle physics (and in quantum mechanics) is reviewed and discussed, mainly by exploiting the explicit consequences of the peculiar relativistic mechanics of Tachyons. Particular attention is paid: (i) to tachyons as the possible carriers of interactions; (ii) to the possibility of ''vacuum decays'' at the classical level; (iii) to a Lorentz-invariant bootstrap model; (iv) to the apparent shape of the tachyonic elementary particles and its possible connection with the de Broglie wave-particle dualism. (author).

215

Random motion of a particle emitting and absorbing tachyons  

International Nuclear Information System (INIS)

Random motion of a particle, emitting and absorbing tachyons, is investigated. It is shown that if bradyon is in equilibrium with neutral gas, i.e. it absorbs and emits tachyons, which do not have any charges, tha particle with each absorption-emittance of a tachyon changes its energy and momentum, never varying its own mass, and as a result it moves like a brownian particle. Thus, bradyon, interacting with tachyon gas, increases its momentum continuously in agreement with the Einstein-Fokker-Planck type equation.

216
218

Higher harmonics of spontaneous radiation of ultrarelativistic channeled particles  

International Nuclear Information System (INIS)

The case of spontaneous radiation of channeled ultrarelativistic particles is considered when the dipolarity condition is not satisfied. The change of the particle longitudinal velocity affecting the maximum radiation frequency is included. The angular and frequency characteristics of the radiation for superhigh energies are studied for the first time. It is shown that there is an optimum energy at which the radiation density is maximum. The influence of the angle at which electrons enter a crystal and of the beam divergence on the radiation is investigated. The problem of quasichanneled particle radiation and also the radiation in axis-plane transitions are considered. (author).

1980-06-01

219

Handling boundary constraints for numerical optimization by particle swarm flying in periodic search space  

CERN Document Server

The periodic mode is analyzed together with two conventional boundary handling modes for particle swarm. By providing an infinite space that comprises periodic copies of original search space, it avoids possible disorganizing of particle swarm that is induced by the undesired mutations at the boundary. The results on benchmark functions show that particle swarm with periodic mode is capable of improving the search performance significantly, by compared with that of conventional modes and other algorithms.

2005-01-01

220

Grassmann-odd Nambu bracket on Grassmann algebra  

International Nuclear Information System (INIS)

... Ukraine) INIS-UA--107 211 p. PHYSICS OF ELEMENTARY PARTICLES AND

2006-09-19

224

Fibrous Carbon  

Science.gov (United States)

... was noted. It was reported that similar fibers also grew on particles of thermal carbon black at a temperature of 10500 and in an atmosphere ...

1963-05-10

225

Electromagnetic properties of generalized Majorana particles  

Energy Technology Data Exchange (ETDEWEB)

We prove a theorem stating that a massive Majorana particle (a CPT-self-conjugate particle) with arbitrary spin J can possess only an anapole moment and multipoles of that. We also show that massless Majorana particles, except those of spin (1/2, do not have any single-photon electromagnetic form factor.

1989-02-20

229

Concept of Plasma Spraying System for Solid Oxide Fuel Cell: Heating Studies of YSZ Particle in Plasma Jet  

International Nuclear Information System (INIS)

One of several methods to build YSZ electrolyte of SOFC is plasma spraying. This system heats particle to a melting point and then pushing them into target and forming a deposition. This paper presents heating studies of YSZ particle in plasma jet. By simple model it is shown that the required time such those YSZ particle with grain size of 50 ?m to be melt is around 12 x 10-4 second. (author)

2006-07-01

230

Climate Change: The Role of Particles and Gases  

ScienceCinema

...global warming ...the effects of global warming ...also the ? that global warming ...

232

Bragg curve spectroscopy detector for particle identification  

International Nuclear Information System (INIS)

The operation principle, construction and characteristics of the Bragg curve spectroscopy detector (BCS detector) are described. The electric field of the BCS detector is parallel to the particle trajectories. The detector was tested by 8.78 MeV and 6.02 MeV #alpha# particles from a ThC-ThC's source. The energy resolutions are 1.5% and 2.6% respectively for two groups of #alpha# particles, and the charge resolution is 2.7%. Further test experiments with heavy ions will be arranged.

233

Application of alpha-particle spectrometry in post-irradiation research and reprocessing  

Energy Technology Data Exchange (ETDEWEB)

Current applications of ..cap alpha..-particle spectrometry in post-irradiation research and reprocessing are reviewed. Implementation of procedures and techniques described in the literature to the particular samples at S.C.K./C.E.N. often results in a combined radiochemical method where ..cap alpha..-particle spectrometry is used to complement or enforce results obtained by other methods. Typical cases are reported and results obtained by different methods are compared to the results obtained by ..cap alpha..-particle spectrometry.

1984-04-01

234

A Leptonic-Hadronic Model for the Afterglow of Gamma-Ray ...  

Science.gov (United States)

... PHYSICS ATOMIC AND MOLECULAR PHYSICS AND SPECTROSCOPY NUCLEAR PHYSICS & ELEMENTARY PARTICLE PHYSICS. ...

2010-11-20

235

Non-linearity and hysteresis of Hall effect in magnetorheological suspensions with conducting carrier  

Energy Technology Data Exchange (ETDEWEB)

In this article a production method of a magnetorheological suspension composed with silicon steel particles of size 0.1-0.15 mm and 4% silicon content is described. Steel particles were dispersed in a conducting carrier of a by mixture of graphite particles with size 2-5 {mu}m and cedar wood oil. The filling factor of the suspension with the silicon steel particles and with graphite particles amounted to 0.25-0.40. Samples of this suspension were placed in a rectangular vessel with electrodes and used for the investigation of the Hall effect in magnetic field with induction 0-8 T, generated by Bitter-type magnet. A non-linear dependence of Hall voltage on the induction of the applied magnetic field and a hysteresis loop of this voltage in the shape of inclined digit eight were found. The causes of the observed effects is the ordering of silicon steel particles ...

2003-08-01

236

Magnetospheric particle acceleration and X-ray emission of pulsars  

CERN Document Server

The available data on isolated X-ray pulsars, their wind nebulae, and the supernova remnants which are connected to some of these sources are analyzed. It is shown that electric fields of neutron stars tear off charged particles from the surface of neutron star and trigger the acceleration of particles. The charged particles are accelerated mainly in the field of magneto-dipole radiation wave. Power and energy spectra of the charged particles depend on the strength of the magneto-dipole radiation. Therefore, the X-ray radiation is strongly dependent on the rate of rotational energy loss and weakly dependent on the electric field intensity. Coulomb interaction between the charged particles is the main factor for the energy loss and the X-ray spectra of the charged particles.

2007-01-01

237

Complex plasma: dusts in plasma  

International Nuclear Information System (INIS)

Dust particles in a plasma are charged negatively and are subject to various types of forces, including a drag force by plasma particles and a force due to the collective nature of a plasma. Dust particles are found in a sheath in laboratories balanced by the gravitational force and the electric force, while dust particles in space are ubiquitous, including planetary magnetospheres and interstellar space. Because of the novel nature of a complex system involving plasma particles and dust particles in a collective way, the dusty plasma is often called a complex plasma. The complex plasma is characterized by two distinctly different scales in time and in space. The plasma with electrons, ions and neutrals is characterized by the collective motion with a fast time scale and a short wavelength, while the dust particles move in a slow time scale ...

2007-04-21

238

Comparative study of three dimensional numerical simulations of particle dispersion in a turbulent air flow  

International Nuclear Information System (INIS)

This paper describes the study of particles' dispersion in an isotropic turbulent flow. The particle's motion and the turbulent flow characteristics are calculated independently. While the particles' displacement is computed by the author's code, the flow is simulated with a commercial code : PowerFLOW. The particles and the flow are coupled through the relative velocity component of the aerodynamic force. When the simulated flow is turbulent, a turbulence regeneration model is used in order to get the flow instantaneous velocity. Validation of the method is done by comparing the particles' dispersion obtained with experimental results from literature and with the results calculated by FLUENT. Good accordance is found between numerical studies and experimental results. However, comparison between results of PowerFLOW coupled to the author's code and results from FLUENT shows ...

2004-05-09

239

Acceleration of particles in pulsar magnetosphere and the X-ray radiation  

CERN Document Server

The available data of single X-ray pulsars, their wind nebulae, and the SNRs which are connected to some of these sources are analysed. It is shown that electric field intensity of neutron stars tears off charged particles from the surface of neutron star and triggers the acceleration of particles. The charged particles are accelerated mainly in the field of magnetodipole radiation wave. Power and energy spectra of the charged particles depend on the strength of the magnetodipole radiation. Therefore, the X-ray radiation is strongly dependent on the rate of rotational energy loss and weakly dependent on the electric field intensity. Coulomb interaction between the charged particles is the main factor for the energy loss and the X-ray spectra of the charged particles.

2004-01-01

240

Radiative transfer in a solar absorbing particle laden flow  

Science.gov (United States)

A possible receiver configuration is a cavity in which a falling sheet of solid particles is directly irradiated by the concentrated solar flux passing through the aperture. Regardless of the particular geometry, the radiative transfer within the falling particle curtain must be studied in order to determine the net radiative heating rate for the particles. A discrete ordinate radiative transfer model has been developed to predict the radiative coupling within the falling particle curtain. The model determines how much energy is absorbed by the particles, how much is transmitted to the rear wall of the receiver, and determines the effects of particle scattering and thermal emission on the net radiation absorbed by the particles. The model accounts for the directional nature of the radiation field, particle scattering, ...

1985-11-01

241

Quantum Secure Direct Communication with Four-Particle Genuine Entangled State and Dense Coding  

Science.gov (United States)

A quantum secure direct communication scheme using dense coding is proposed. At first, the sender (Alice) prepares four-particle genuine entangled states and shares them with the receiver (Bob) by sending two particles in each entangled state to him. Secondly, Alice encodes secret information by performing the unitary transformations on her particles and transmits them to Bob. Finally, Bob performs the joint measurements on his particles to decode the secret information. The two-step security test guarantees the security of communication.

2009-07-01

242

Numerical prediction of flow field and particle trajectory in a hard disk drive  

Energy Technology Data Exchange (ETDEWEB)

A flow field and particle trajectory in a HDD (Hard Disk Drive) between two rotating disks in axisymmetric enclosures is investigated using CFD code FLUENT/UNS. The RNG k-{epsilon} model is used as a turbulent model. In this study, the flow field between two disks are symmetric, and the flow field near the enclosure is very complex. Cross stream vectors are shown both for blowing and no blowing from the hub. The larger a particle, the more fast the particle deposits at the walls. In the case of blowing from the hub, the more fast the particle deposits at the walls. (author). 9 refs., 12 figs., 1 tab.

1999-11-01

243

Multigroup transfer matrices for charged-particle and neutron-induced reactions Part III: Energy conservation and local deposition  

Energy Technology Data Exchange (ETDEWEB)

Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.

1983-11-01

244

Multigroup transfer matrices for charged-particle and neutron-induced reactions Part III: Energy conservation and local deposition  

International Nuclear Information System (INIS)

Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.

1983-01-01

245

Method for production of uranium dioxide particles from uranium hexafluoride by growing process in fluidized bed  

International Nuclear Information System (INIS)

Processes of production and purification (necessary for fabricating fuel elements) of powdery uranium dioxide with particle size up to 1000 #mu#m and more have been studied. Developed is continuous process of UO_2 production with above particle size by converting uranium hexafloride into UO_2 solid particles in fluidized bed while their interaction with water vapor and hydrogen on the uranium dioxide nucleus material. The method allows to conduct continuous selection from the apparatus of UO_2 powder fraction with particle size near 1000 #mu#m without nucleus material additional feed.

246

In-place testing of HEPA filter systems by the single-particle, particle-size spectrometer method  

Energy Technology Data Exchange (ETDEWEB)

This standard describes the procedure and equipment for in-place testing of HEPA filter systems by the single-particle, particle-size (SPPS) spectrometer method. This method provides the capability for evaluating the effectiveness (i.e., decontamination factor or DF) of systems consisting of one or more stages of HEPA filters against submicrometer aerosols in discrete particle-size ranges. It is particularly useful for testing of multi-stage HEPA filter installations and for testing of very large (50,000 cfm installed capacity) single-stage systems where it is desired to minimize the quantity of challenge aerosol required.

1981-12-01

247

Development of thin foil Faraday collector as a lost alpha particle diagnostic for high yield D-T tokamak fusion plasmas  

Energy Technology Data Exchange (ETDEWEB)

Alpha particle confinement is necessary for ignition of a D-T tokamak fusion plasma and for first wall protection. Due to high radiation backgrounds and temperatures, scintillators and semiconductor detectors may not be used to study alpha particles which are lost to the first wall during the D-T programs on JET and ITER. An alternative method of charged particle spectrometry capable of operation in these harsh environments, is proposed: it consists of thin foils of electrically isolated conductors with the flux of alpha particles determined by the positive current flowing from the foils. 2 refs., 3 figs.

1994-07-01

248

Compound nucleus contribution to the alpha particle scattering from "2"8Si  

International Nuclear Information System (INIS)

In the case of inelastic scattering of alpha particles to the 3"+ state, the averaged angular distributions show a characteristic shape, corresponding to the excitation of such an unnatural parity state by alpha particles in the compound nucleus process. The modified Hauser-Feshbach cross-section calculations give a good description of the averaged distributions for the alpha particle scattering to the 3"+ state and the compound nucleus parameters could be extracted. The calculations of the compounds nucleus contributions to the other states in the case of 24 MeV alpha particle scattering from "2"8Si show that this contribution is not negligible and in the case of the scattering to the 4"+ state seems to be dominant. (Z.M.).

249

The impact of avoidable mortality on life expectancy at birth in Spain: changes between three periods, from 1987 to 2001  

UK PubMed Central (United Kingdom)

Objective:To evaluate the impact of avoidable mortality on the changes in life expectancy at birth in Spain.Methods:Standard life table techniques...Full Text Available

2008-09-01

250

Sexual Dysfunction and Symptom Impact in Men with Long-Standing Type 1 Diabetes in the DCCT/EDIC Cohort  

UK PubMed Central (United Kingdom)

IntroductionMale sexual dysfunction is a common complication of diabetes (DM), but the relative impact of erectile dysfunction (ED), orgasmic dysfunction (OD), and/or...Full Text Available

2009-07-01

251

Method of pipe whip and impact analyses  

Energy Technology Data Exchange (ETDEWEB)

We successfully reproduce one of the French pipe whip experiments with the computer code WIPS. The WIPS results are in excellent agreement with the experimental data and the French computer code TEDEL. This justifies the use of its pipe element in conjunction with its U-bar element in a simplified method of impact analyses.

1983-11-21

252

Impact of the 3,6,9-Trioxadecyloxy Group on Desazadesferrithiocin Analogue Iron Clearance and Organ Distribution  

UK PubMed Central (United Kingdom)

The impact of introducing a 3,6,9-trioxadecyloxyl group at various positions of the desazadesferrithiocin (DADFT) aromatic ring on iron clearance and organ distribution is described. Three DADFT...Full Text Available

2007-07-12

253

Impact of repeated four-monthly anthelmintic treatment on Plasmodium infection in preschool children: a double-blind placebo-controlled randomized trial  

UK PubMed Central (United Kingdom)

BackgroundHelminth infections can alter susceptibility to malaria. Studies need to determine whether or not deworming programs can impact on Plasmodium infections...Full Text Available

254

Impact of extreme events on coastal zones and small islands in the context of climate change  

Energy Technology Data Exchange (ETDEWEB)

The paper presents a review of the current state of knowledge on the likely impacts of extreme weather and climate events on coastal zones and small islands in the context of climate change. Possible response options, including prevention, preparedness and adaptation, are indicated.

1995-07-10

255

Impact of an Electronic Medical Record on Diabetes Quality of Care  

UK PubMed Central (United Kingdom)

PURPOSE This study was designed to evaluate the impact of electronic medical record (EMR) implementation on quality of diabetes care.METHODS We conducted a 5-year longitudinal...Full Text Available

2005-07-01

256

Impact of Lifelong Sedentary Behavior on Mitochondrial Function of Mice Skeletal Muscle  

UK PubMed Central (United Kingdom)

This study investigated the impact of lifelong sedentariness on skeletal muscle mass and mitochondrial function. Thirty C57BL/6 strain mice (2 months) were randomly divided into three groups (young-Y;...Full Text Available

2009-09-01

257

Impact of Geographical Proximity on Health Care Seeking Behaviour in Northern Oman  

UK PubMed Central (United Kingdom)

Objectives:Despite its impact on health policy, the relationship between geographical proximity and health care seeking has received scant attention in the medical literature. This...Full Text Available

2008-11-01

258

Impact of Electronic Health Record Clinical Decision Support on Diabetes Care: A Randomized Trial  

UK PubMed Central (United Kingdom)

PURPOSE We wanted to assess the impact of an electronic health record–based diabetes clinical decision support system on control of hemoglobin A1c (glycated hemoglobin),...Full Text Available

2011-01-01

259

Impact of Bt corn pollen on monarch butterfly populations: A risk assessment  

UK PubMed Central (United Kingdom)

A collaborative research effort by scientists in several states and in Canada has produced information to develop a formal risk assessment of the impact of Bt corn on monarch butterfly...Full Text Available

2001-10-09

260

Impact of Basic Computerized Prescribing on Outpatient Medication Errors and Adverse Drug Events  

UK PubMed Central (United Kingdom)

Few data exist about the impact of computerized prescribing systems on outpatient medication errors (MEs) and adverse drug events (ADEs). We compared the rates of MEs and ADEs in handwritten sites versus...Full Text Available

2002-11-01

261

Functional Impact of White Matter Hyperintensities in Cognitively Normal Elderly  

UK PubMed Central (United Kingdom)

ObjectiveTo investigate the impact white matter hyperintensities (WMH) detected on MRI have on motor dysfunction and cognitive impairment in non-demented elderly...Full Text Available

2010-11-01

262

Exploring posttraumatic growth in children impacted by Hurricane Katrina: Correlates of the phenomenon and developmental considerations  

UK PubMed Central (United Kingdom)

This study explored posttraumatic growth (PTG), positive change resulting from struggling with trauma, among 7- to 10-year-olds impacted by Hurricane Katrina. Analyses focused on child self-system...Full Text Available

2010-07-01

263

Economic Impact Analysis of Proposed Effluent Limitations Guidelines and Standards for the Pesticide Manufacturing Industry.  

Science.gov (United States)

The report details the economic impact of two alternative regulatory options; a Treated Discharge Option and a Zero Discharge Option on facilities that would have to comply with the regulations as part of the reproposal of effluent limitations and standar...

1992-01-01

264

Economic Impact Analysis of Proposed Effluent Limitations Guidelines and Standards for the Centralized Waste Treatment Industry.  

Science.gov (United States)

This report estimates the economic and financial effects of compliance with the proposed effluent limitations guidelines and standards for the Centralized Waste Treatment (CWT) industry. The Environmental Protection Agency (EPA) has measured these impacts...

1995-01-01

265

Data Quality of General Practice Electronic Health Records: The Impact of a Program of Assessments, Feedback, and Training  

UK PubMed Central (United Kingdom)

Objective: The aim of this study was to investigate the impact of a program of repeated assessments, feedback, and training on the quality of coded clinical data in general practice.Design:...Full Text Available

2004-01-01

266

Biofuels: Report to Congress  

Science.gov (United States)

Section 204 of the Energy Independence and Security Act of 2007 (EISA 2007) requires EPA to assess and report to Congress on the impacts to date and likely future impacts of the increased use of biofuels as required by the Clean Air Act, section 211(0). Environmental issues (...

267

An outbreak of sand impaction in postpartum dairy cows  

UK PubMed Central (United Kingdom)

Twenty-two cases of indigestion occurred in a 650-cow herd. Five cows had severe sand abomasal impaction, diagnosed by laparotomy. The pH of prepartum cows’ urine was < 6.0 and of sand...Full Text Available

2007-10-01

268

A systematic review of published evidence on intervention impact on condom use in sub?Saharan Africa and Asia  

UK PubMed Central (United Kingdom)

ObjectiveThere has been much debate about the value of condoms in HIV/STI programming. This should be informed by evidence about intervention impact on condom use, but there is limited...Full Text Available

2007-12-01

269

Visual impact evaluation of a wind park in a Greek island  

Energy Technology Data Exchange (ETDEWEB)

The visual impact of wind turbines is one of the main factors affecting public acceptance of wind parks. This paper evaluates the visual impact of a wind park in Chania, Crete, using the Spanish method of evaluation. The outcomes are combined with the psychometric testing of the residents by the use of questionnaires and with the values of the Spanish method about various scenarios concerning the size of the wind park (double, half, one wind turbine). The results of the study prove that the quantification of the potential visual impact could minimize this, apparently, main reason that affects public acceptance. (author)

2009-04-15

270

Underground electric-power transmission-system environmental impact assessment  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy, Division of Electric Energy Systems, has undertaken to identify the environmental issues and potential impacts associated with the installation of underground electric power transmission systems. This study reports the results of investigations into the advanced cable technologies being considered for future underground applications, as part of the development oriented research program of the Division of Electric Energy Systems. While the technology involves a high level of sophistication, there are relatively few impacts to the environment that are potentially significant, and of these none are inherently non-mitigable. Route planning, system design, and methods of construction and accident response can be pursued in order to minimize impacts where strict constraints are appropriate.

1982-03-01

271
274

Selenium - Global Change Master Directory (GCMD)  

Science.gov (United States)

This study is an evaluation of the potential environmental impacts of contaminated groundwater from the ASARCO metals refining facility adjacent to the ...

275

Principles of air pollution meteorology  

Energy Technology Data Exchange (ETDEWEB)

This book is divided into the following chapters: the atmospheric boundary layer; atmospheric diffusion; pollutants and their properties; and environmental monitoring and impact.

1990-01-01

276
279

Global Warming Communications Overview (WMV, 15.09 MB)  

Science.gov (United States)

... insight into the best way to communicate about global warming and it's impact on wildlife to the " ... ...

281

EPA: Environmental Quality and Recreation: Global Warming  

Science.gov (United States)

Archived Web resource. Information about the impacts of global warming on the environmental quality and recreation, such as ... ...

282

DIGITAL LIBRARIES: IMPACT ON SCIENCE ... - MUSPIN - NASA  

Science.gov (United States)

digital libraries, which was identified as a national challenge in the Information ... The linkages between the many digital libraries and information services are ...

283

Confronting Climate Change in New Jersey and the Northeast: Science, Impacts and Solutions  

ScienceCinema

...changes consistent with global warming ? uh how to regional scale within ...

284

Carbon Smackdown: Cookstoves for the developing world  

ScienceCinema

...contribution to global warming ...states i think impact of global warming ? and ...contributor to global warming ...

285

Battery Thermal Management System Design Modeling  

Energy Technology Data Exchange (ETDEWEB)

Looks at the impact of cooling strategies with air and both direct and indirect liquid cooling for battery thermal management.

2006-11-01

287

The environmental impacts of a large gas-fired combined cycle power station  

Energy Technology Data Exchange (ETDEWEB)

The paper discusses the potential environmental impacts associated with the operation of a large, say 350 MWe, gas-fired combined cycle power station. It concludes that if appropriate control methods are introduced at the design stage of the plant, environmental impacts are minimal and can be considered acceptable. (author).

1991-11-01

288

Scenario-Based Actions to Upgrade Small-Scale Furniture Producers and their Impacts on Women in Central Java, ...  

Science.gov (United States)

... Producers and their Impacts on Women in Central Java, IndonesiaActions basées sur des scénarios visant à élever ... impact sur les femmes dans le centre de Java, en IndonésieInvestigación-acción basada en...

289

Mitigating socio-economic impacts of energy development  

Energy Technology Data Exchange (ETDEWEB)

This study provides information on energy resource development and the efforts of State and local communities in the Rocky Mountain, Appalachian, and coastal regions to deal with the related social and economic impacts. It also provides information on the range of options and resources generally available to States and local communities from local, State, industry, and Federal sources to plan for and mitigate the adverse effects of energy development. Onsite visits and interviews with State, local, and Federal officials and private industry involved in mitigating socioeconomic impacts were made.

1982-03-02

290

Development Application - Terra Nova Development - Supplement B to the Application  

Energy Technology Data Exchange (ETDEWEB)

Supplement B to the Terra Nova Development Application provides a description of the floating production storage and offloading (FPSO) vessel system selected for the development, a summary of the reasons for selecting the system, and the impact of this selection on the Development Plan, the Benefits Plan, the Environmental Impact Statement and the Socio-Economic Impact Statement. There is also a description of the contractor alliance approach to be used in the Terra Nova Development. Refs., tabs., figs.

1997-02-01

291

Stochastic Finsler D-particle Space-Time Foam Enhances Dark Matter Relics  

CERN Document Server

Within the context of space-time (D-particle) foam in string/brane-theory it is demonstrated that it is possible to generate non-extensive statistics. The D-particle foam model involves point-like brane defects (D-particles), which provide the topologically non-trivial foamy structures of space-time. The D-particles can capture and emit stringy matter and this leads to a recoil of D-particles. It is indicated how one effect of such a recoil of D-particles is a back reaction on the space-time metric of Finsler type which is stochastic. We show that such a type of stochastic space-time foam can lead to cosmological effects similar to those induced by modifications of particle distributions within the framework of Tsallis entropies. The restrictions placed on the free parameters of the Finsler type metric are obtained from solving the Boltzmann ...

2010-01-01

292

A new lagrangian particle method to describe turbulent flows of fully compressible ideal gases  

CERN Document Server

There are several approaches to describe flows with particles e.g. Lattice-Gas Automata (LGA), Lattice-Boltzmann method (LBM) or smoothed particle hydrodynamics (SPH). These approaches do not use fixed grids on which the Navier-Stokes equations are solved via e.g. finite volume method. The flow is simulated using a multitude of particles or particle density distributions, which interacts and due to statistical laws and an even more fundamental approach than the Navier-Stokes equation, the averaged flow variables can be derived. After a short summary of the most popular particle methods the new DMPC (Dissipative Multiple Particles Collision) approach will be presented. The DMPC-model eliminates some of the weak points of the established particle methods and shows high potential for more accurate CFD solution especially in areas where standard ...

2008-01-01

293

Preparation of ZnO-Al2O3 Particles in a Premixed Flame  

DEFF Research Database (Denmark)

Zinc oxide (ZnO) and alumina (Al2O3) particles are synthesized by the combustion of their volatilized acetylacetonate precursors in a premixed air-methane flame reactor. The particles are characterized by XRD, transmission electron microscopy, scanning mobility particle sizing and by measurement of the BET specific surface area. Pure (?-)alumina particles appear as dendritic aggregates with average mobile diameter 43-93 nm consisting of partly sintered, crystalline primary particles with diameter 7.1-8.8 nm and specific surface area 184-229 m2/g. Pure zinc oxide yields compact, crystalline particles with diameter 25-40 nm and specific surface area 27-43 m2/g. The crystallite size for both oxides, estimated from the XRD line broadening, is comparable to or slightly smaller than the primary particle diameter. The specific surface area ...

2000-01-01

294

A model for estimating the hydraulic conductivity of granular material based on grain shape, grain size, and porosity  

Energy Technology Data Exchange (ETDEWEB)

Particle shape is an important parameter in numerous civil, environmental, and petroleum engineering applications. In ground-water flow, the shape of individual particles comprising the soil affects the soil`s pore size distribution and, hence, the important flow characteristics such as hydraulic conductivity and headloss. A model for delineating the relative importance of particle size, particle shape, and porosity, (and their interactions), in explaining the variability of hydraulic conductivity of a granular porous medium is developed and tested. Three types of porous media are considered in this work: spherical glass beads; granular sand; and irregularly shaped, shredded glass particles. A reliable method for quantifying the three-dimensional shape and packing of large samples of irregular particles based on their angle of repose is presented. The results of ...

1995-11-01

295

Size and morphology of heavy-duty vehicle particle emissions; Raskaan ajoneuvokannan hiukkaspaeaestoen koko ja morfologia - HD-PM  

Energy Technology Data Exchange (ETDEWEB)

Formation of particles from heavy duty diesel and CNG vehicles was studied in laboratory conditions. PM, nano and soot mode particle emissions formed from buses of Euro 2-5 -emission levels were studied in relation to age and type approval characteristics of the vehicle. Characteristic particle emission factors from city driving were obtained by driving the buses on VTT's heavy duty chassis dynamometer applying the transient Braunschweig city cycle. The vehicles were a representative set of Euro 2 to 3 emission categories, supplemented with Euro 4-5 (EEV) -targeted CRT, CNG and DPF cars. Particle number emissions from Euro 4 to 5 buses were 1/100-1/1000 and mass emissions 1/10-1/100 of those of the current fleet. Particle emission from natural gas buses and after an advanced CRT trap contained almost entirely liquid < 60 nm nano particles, which ...

2006-10-15

296

The combustion aerodynamics of a pulverized coal low NO{sub x} swirl burner in an industrial boiler  

Energy Technology Data Exchange (ETDEWEB)

This paper discusses the application of a Computational Fluid Dynamics (CFD) code (FLUENT) to predict temperature and velocity profiles, and particle trajectories in an industrial fired by a low NO{sub x} pulverized coal swirl burner. The predictions of the code were compared to experimental measurements of gas temperature, particle size distribution, and particle velocities. The diagnostics employed were a suction pyrometer and a Particle Counter Sizer Velocimeter Probe (PCSV-P). Good agreement was found between the temperature predictions and the measurements. In situ particle size distributions were predicted accurately using the Baum and Street model with a swelling factor of zero. The numerical modeling indicated that the Type II flow issued from the burner could be transformed into Type III flow, by eliminating swirl from the primary air stream, which provided the preferred ...

1996-12-31

297

Synthesis of magnetic particles via a cationic-anionic surfactant vesicle method  

Energy Technology Data Exchange (ETDEWEB)

In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe{sup 3+} and Fe{sup 2+}) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.

2006-10-15

298

Synthesis of magnetic particles via a cationic-anionic surfactant vesicle method  

International Nuclear Information System (INIS)

In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe"3"+ and Fe"2"+) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.

2006-10-01

299

New wear resistant composite material  

Energy Technology Data Exchange (ETDEWEB)

A composite material consisting of WC-Co particles in a steel matrix was fabricated by sintering mixtures of WC-Co particles and a steel powder and infiltrating the sintered pieces with a copper alloy. Its wear resistance and mechanical properties were studied as a function of the content in WC-Co particles and other characteristics of the composite material microstructure. Infiltration provided a simple means to obtain a strong cohesion between WC-Co particles and the steel matrix. An effective matrix protection against wear is obtained with relatively low additions of particles especially with a silica abrasive which is soft with respect to cemented carbide. The experimental results show that this material has good mechanical properties and wear resistance. Depending upon abrasion resistance, wear losses are reduced up to 10 times by a 30 vol% addition of cemented carbide ...

1983-01-01

300

Molecular dynamics study of TiO2/poly(acrylic acid-co-methyl methacrylate) and Fe3O4/polystyrene composite latex particles prepared by heterocoagulation  

British Library Electronic Table of Contents (United Kingdom)

All-atom molecular dynamics simulations were used to study the morphology of polymer/inorganic composite particles prepared by heterocoagulation. The results were also compared to those of our previous study of the preparation of TiO2/poly(acrylic acid-co-methyl methacrylate) and Fe3O4/polystyrene composite particles. In the simulation system, polymer or inorganic particles were simulated by surface-charge-modified C60 or Na atoms. Through a combination of analysis of the radial distribution functions of charged atoms and snapshots of the equilibrated structure, three kinds of particle distributions were observed under different conditions. When the polymer and inorganic particles had opposite surface charges and their sizes were very different, the composite morphology showed a core-shell...

2010-01-01

301

Experimental limits on quarks, tachyons, and massive particles in cosmic rays  

Energy Technology Data Exchange (ETDEWEB)

A large detector with high redundancy is used to search for various types of anomalous particles in cosmic rays at sea level. The detector is sensitive to zenith angles between 45/sup 0/ and 90/sup 0/. Previously obtained limits on the fluxes of charge (1/3) and (2/3) particles are reduced to 2.9 x 10/sup -10/ and 2.6 x 10/sup -10/ cm/sup -2/sr /sup -1/ sec/sup -1/, respectively. The flux of ionizing tachyons is determined to be less than 2.4 x 10/sup -9/ cm/sup -2/ sr/sup -1/ sec/sup -1/. The massive-particle flux limit we obtain is inconsistent with previous claims of such particles assuming that these particles are isotropic in zenith angle.

1982-10-01

302

Experimental limits on quarks, tachyons, and massive particles in cosmic rays  

International Nuclear Information System (INIS)

A large detector with high redundancy is used to search for various types of anomalous particles in cosmic rays at sea level. The detector is sensitive to zenith angles between 45"0 and 90"0. Previously obtained limits on the fluxes of charge (1/3) and (2/3) particles are reduced to 2.9 x 10"-"1"0 and 2.6 x 10"-"1"0 cm"-"2sr "-"1 sec"-"1, respectively. The flux of ionizing tachyons is determined to be less than 2.4 x 10"-"9 cm"-"2 sr"-"1 sec"-"1. The massive-particle flux limit we obtain is inconsistent with previous claims of such particles assuming that these particles are isotropic in zenith angle.

303

An experimental method for measurement of strain distribution between wood the flour particles and polymer matrix on micro-mechanical level  

British Library Electronic Table of Contents (United Kingdom)

Wood plastic composites (WPCs) are comprised of wood flour and thermoplastic polymer. The matrix is typically high-density polyethylene, poly (vinyl chloride), or polypropylene. The effect of morphology and micromechanics of wood flour particles on the mechanical performance of the bulk composite is a relatively unexplored area. The knowledge about the in situ properties of wood particles and the interfacial properties between the wood particles and the polymer matrix in the bio-composites is very limited. The objective of this work is to characterize the full-field deformation and strain distribution in and around wood particles embedded in polymer matrix. The mechanical tests are performed in small-scale tensile loading stage on thin composite samples containing 1-3 wood particles orient...

2011-01-01

304

A principle of charged particle trapping by RF electromagnetic field in the spherical cavity  

Energy Technology Data Exchange (ETDEWEB)

A new principle of particle trapping in the simple spherical cavity using both electric and magnetic components of radiofrequency electromagnetic field is proposed. The electric component of H {sub 12} oscillating mode drives the fast particle oscillations, while the magnetic component synchronously bends the trajectories to the cavity center. A specially developed theory of particle stability predicts dense and energetic electron cluster in the trap. Numerical simulations of particle dynamics in the complete electromagnetic field taking into account both space charge and particle-induced magnetic field are in good agreement with the analytic results, giving a density of 2.6*10{sup 1} electrons/cm{sup 3} and an average kinetic energy of around 30 keV at an operating frequency of 3 GHz. Being used at lower frequency, spherical cavity can trap protons and heavier ions too, but with ...

2005-11-21

305

A new method for quantifiable and controlled dosage of particulate matter for in vitro studies: The electrostatic particulate dosage and exposure system (EPDExS)  

British Library Electronic Table of Contents (United Kingdom)

An exposure chamber is described for the quantifiable addition of fine and ultrafine aerosol particulate matter directly to cells and used to demonstrate the in vitro cytotoxicity of fine 1,4-naphthoquinone particles to murine lung epithelial cells. The electrostatic particulate dosage and exposure system (EPDExS) operates on the principle of electrostatic precipitation and is shown to deposit fine and ultrafine aerosol particles directly to cells with 100% efficiency for particle diameters in the range of 40-530nm. This range is not limited by the EPDExS, but rather by the aerosolization method used for this study. Numbers of particles deposited onto the cells are counted with a condensation particle counter, negating any need to calculate or estimate particle exposure. The process of par...

2008-01-01

306

Viscoelastically prestressed polymeric matrix composites - Potential for useful life and impact protection  

British Library Electronic Table of Contents (United Kingdom)

A viscoelastically prestressed polymeric matrix composite (VPPMC) is produced by applying tension to polymeric fibres, the tensile load being released prior to moulding the fibres into a matrix. Following matrix solidification, compressive stresses imparted by the viscoelastically strained fibres improve composite tensile, flexural and impact properties. This study focuses on the potential for useful life and impact protection capability by performing Charpy impact tests on nylon 6,6 fibre-polyester resin samples subjected to accelerated ageing. Prior to testing, time-temperature superposition principles were used, the samples being aged by heating to 60degreeC for periods representing a 10-fold increase over previous work. The results demonstrated no deterioration in impact performance ov...

2010-01-01

307

The impacts and costs of global warming. A review  

Energy Technology Data Exchange (ETDEWEB)

There is now a scientific consensus that current rates of accumulation of greenhouses gases in the atmosphere will result in significant global warming and climate change. These changes are likely to have important impacts on a wide range of human activities and the natural environment. There has now been a considerable weight of literature published on the impacts of global warming, much of it very recent. This report seeks to summarise the important results, to analyse the uncertainties and to make a preliminary analysis of the feasibility of monetarising these environmental costs. The impacts of global warming are divided into ten major categories: agriculture, forests and forestry, terrestrial ecosystems and biodiversity, hydrology and water resources, sea level rise and coastal zones, energy, infrastructure/transport/industry, human health and air quality, oceans, and cryospheric impacts. The ...

1991-09-01

308

Modelling the impacts of weather and climate variability on crop productivity over a large area: A new super-ensemble-based probabilistic projection  

British Library Electronic Table of Contents (United Kingdom)

Estimates of climate change impacts are plague with uncertainties from many physical, biological, and social-economic processes. Among the urgent research priorities, more comprehensive assessments of impacts that better represent the uncertainties are needed. Here, we develop a new super-ensemble-based probabilistic projection approach to account for the uncertainties from CO2 emission scenarios, climate change scenarios, and biophysical processes in impact assessment model. We demonstrate the approach in addressing the probabilistic changes of maize production in the North China Plain in future. The new process-based general crop model, MCWLA [Tao, F., Yokozawa, M. Zhang, Z., 2009. Modelling the impacts of weather and climate variability on crop productivity over a large area: a new proc...

2009-01-01

309

Introduction to 'MINEO' project of European community and its enlightenments to monitoring and assessment of environmental impacts caused by mining in China  

Energy Technology Data Exchange (ETDEWEB)

In order to promote environmental damage monitoring and environmental impacts assessment caused by mining in China, the most significant project that uses advanced Earth Observation technology to assess environmental impacts caused by mining, namely MINEO (assessment and monitoring the environmental impact of mining activities in Europe using advanced Earth Observation technology) was introduced and its enlightenment to China were investigated. It was proposed that an integrated technical framework of monitoring environmental impacts caused by mining be designed, quantitative inversion of biological and environmental parameters from RS data be emphasised, hyperspectral Remote Sensing be applied, RS and GIS be integrated with professional models, multi-object applications of RS be implemented, and related standards and specification be drawn up based on typical case study sites. 23 refs., 1 fig.

2008-01-15

310

Economic impact analysis of proposed effluent limitations and standards for the gold placer mining industry  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the study is to analyze the economic impacts that are likely to result from promulgation of the proposed best practicable control technology (BPT), best available technology economically achievable (BAT) and Best Conventional Technology (BCT) effluent limitations and standards on placer mining in the United States. The results of the economic impact analysis will help establish pollution control regulations that are economically achievable. The analysis examines how each of four alternative pollution control technologies affects the financial viability of placer mines in the United States. The impacts examined include reduced profitability, production cutbacks, mine closures, and employment and earning losses, as well as impacts to the local economies.

1985-08-01

311

Laser: a Tool for Optimization and Enhancement of Analytical Methods  

Energy Technology Data Exchange (ETDEWEB)

In this work, we use lasers to enhance possibilities of laser desorption methods and to optimize coating procedure for capillary electrophoresis (CE). We use several different instrumental arrangements to characterize matrix-assisted laser desorption (MALD) at atmospheric pressure and in vacuum. In imaging mode, 488-nm argon-ion laser beam is deflected by two acousto-optic deflectors to scan plumes desorbed at atmospheric pressure via absorption. All absorbing species, including neutral molecules, are monitored. Interesting features, e.g. differences between the initial plume and subsequent plumes desorbed from the same spot, or the formation of two plumes from one laser shot are observed. Total plume absorbance can be correlated with the acoustic signal generated by the desorption event. A model equation for the plume velocity as a function of time is proposed. Alternatively, the use of a static laser beam for observation enables reliable determination of plume velocities even when ...

1997-01-01

312

Distributional Aspects of Climate Change Impacts  

International Nuclear Information System (INIS)

This paper gives a brief review about the state of knowledge on the distributional aspects of climate change impacts. The paper is largely limited to the distribution of impacts between countries (in Section 2). Although there are virtually no estimates reported in the literature, the distribution of impacts within countries is also important. Impact estimates for different sectors (agriculture, health, sea level rise) provides little guidance for estimating differential impacts within countries. It is even harder to find estimates based on social classes. The paper restricts itself to equity about the consequences of climate change. Equity issues about the consequences of emission reduction are ignored here, but should of course be part of a policy analysis. Equity issues about procedures for decision making are also ignored. The paper is organised as follows. Section 2 reviews ...

2002-12-12

313

Systematic interdisciplinary language for environmental analysis under the National Environmental Policy Act  

Energy Technology Data Exchange (ETDEWEB)

Many environmental impact statements (EIS) fail to predict environmental impacts, organize information about those impacts in a concise, logical way, and communicate that information intelligibly. This paper presents a systematic, auxiliary ''language'' for environmental analysis under the National Environmental Policy Act (NEPA), in an attempt to correct this problem. The approach improves communication among disciplinary specialists, between an interdisciplinary team and a decision-maker, and between a federal agency and the general public by helping to identify important issues and impacts, and by reducing time, effort, cost, and paperwork. The basis for the approach is found in the principal aims of the NEPA regulations and other criteria. The interdisciplinary language for environmental analysis consists of a small vocabulary, used in conjuction with a simple ...

1984-01-01

314

Generic assessment of air quality impacts associated with oil and gas development offshore California  

Energy Technology Data Exchange (ETDEWEB)

Oil and gas resources in the offshore areas of the US constitute a significant portion of US recoverable hydrocarbon resources. The exploration, development and production of these offshore resources in California, however, could have significant air quality implications for coastal air basins. This study was developed to address a problem that frequently arises with offshore air quality assessments. Typically, such assessments are performed for a specific activity scenario (e.g., a Federal OCS Lease Sale involving a projected number of drilling rigs, platforms, pipelines, etc.) and assume a projected (but uncertain) level of recoverable oil and gas resources. This study enables interested parties to estimate air emissions and impacts for a wide range of OCS-related development scenarios. The modular emission calculation procedure and the generic impact assessment provide for maximum flexibility in reassessing the emissions and ...

1984-01-01

315

Translocation of particles to the pleural space and tracheobronchial lymph nodes following lung deposition  

Energy Technology Data Exchange (ETDEWEB)

The translocation of particles from the alveolar compartment to the pleural space and tracheobronchial lymph nodes was investigated in rats over a 30 day period following the intrapulmonary instillation of 4 x 10/sup 8/ polystyrene microspheres (1.9 ..mu..m dia.). In initial studies, approx. =10/sup 4/ particles were found in the pleural space compartment on Days 1, 14 and 30 after particle deposition, and most of these were cell-associated. Subsequent pleural space studies indicated, however, that the particles found in this compartment were, at least in part, due to the pleural lavage technique, and, unlike observations reported for some fibers, the translocation of the particles used in our study to the pleural space does not represent an important lung clearance pathway. In regard to particle clearance to the tracheobronchial lymph nodes, the accumulation of ...

1985-01-01

316

On the properties of plasma crystals  

Energy Technology Data Exchange (ETDEWEB)

When a plasma becomes contaminated by foreign particles, generically referred to as dust, the result is called a dusty plasma. At the present time there is a great deal of interest in dusty plasmas because of their roles in terrestrial and extra-terrestrial processes - semiconductor processing, high temperature fusion experiments, stellar formation and the rings of Saturn. This thesis is concerned with the role of dust in processing type plasmas. In the following experiments, artificial dust is introduced into a parallel electrode plasma chamber. Ions and electrons in the plasma charge the dust particles and they become suspended in the plasma due to the balancing of electric and gravitational forces. By illuminating the suspended dust with laser light and using an extremely high speed camera fitted with a macro lens to look at the scattered light, the dust particles are observed directly. Specially written computer ...

1999-07-01

317

DYNAMICS OF SOLIDS IN THE MIDPLANE OF PROTOPLANETARY DISKS: IMPLICATIONS FOR PLANETESIMAL FORMATION  

International Nuclear Information System (INIS)

We present local two-dimensional and three-dimensional hybrid numerical simulations of particles and gas in the midplane of protoplanetary disks (PPDs) using the Athena code. The particles are coupled to gas aerodynamically, with particle-to-gas feedback included. Magnetorotational turbulence is ignored as an approximation for the dead zone of PPDs, and we ignore particle self-gravity to study the precursor of planetesimal formation. Our simulations include a wide size distribution of particles, ranging from strongly coupled particles with dimensionless stopping time #tau#_s #ident to# #OMEGA#t_s_t_o_p = 10"-"4 (where #OMEGA# is the orbital frequency, t_s_t_o_p is the particle friction time) to marginally coupled ones with #tau#_s = 1, and a wide range of solid abundances. Our main results are as follows. (1) Particles ...

2010-10-20

318

Transmutation of minor actinides in high and representative neutron fluxes: the mini-INCA and MEGAPIE projects  

Energy Technology Data Exchange (ETDEWEB)

In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ({sup 241}Am, {sup 242}Am, {sup 242}Pu, {sup 237}Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW spallation target and the ...

2003-07-01

319

Transmutation of minor actinides in high and representative neutron fluxes: the mini-INCA and MEGAPIE projects  

International Nuclear Information System (INIS)

In the framework of nuclear waste transmutation studies, the Mini-INCA project has been initiated at CEA/DSM with objectives to determine optimal conditions for transmutation and incineration of minor actinides (MA) in high intensity neutron fluxes. Our experimental tools based on alpha- and gamma-spectroscopy of the samples and the development of micro fission chambers could gather either microscopic information on nuclear reactions (total or partial cross sections for neutron capture and/or fission reactions) or macroscopic information on transmutation and incineration potentials. Neutron capture cross sections of selected actinides ("2"4"1Am, "2"4"2Am, "2"4"2Pu, "2"3"7Np) have already been measured at ILL, showing some discrepancies when compared to evaluated data libraries but in overall good agreement with recent data. The studies and possibilities offer by the MEGAPIE project to assess neutronic performances of a 1 MW spallation target and the incineration of ...

2003-09-01

320

The magnetic resonance and its agro-industry applications; a review  

International Nuclear Information System (INIS)

The electromagnetic properties that present hydrogen and other nucleus of agro-alimentary products, have allowed widely use of magnetic resonance (MR) to study the composition and internal structure of these biological materials in a micro and macroscopic scale, in a nondestructive way. In this paper the physical principles, basic equipment to measure the MR signals and the MR imaging of any biological sample, are explained. It is also shown a review of the main agro-alimentary applications, emphasizing in the use of this principle to examine the internal quality of fruits and vegetables. In these products, the MR has been used to detect and follow the evolution of different factors that determine the internal quality after harvesting, during storage and after post harvesting processes. The main studies that have been conducted with MR in harvested products are about physiological disorders that take place during storage and conservation of fruits in controlled and ...

321

The importance of turbulence modelling in the design of a novel delivery system for a single-belt steel casting process  

Energy Technology Data Exchange (ETDEWEB)

In this work, a comprehensive model including heat transfer, fluid flow and solidification was used to evaluate the performance of a novel delivery system for a single-belt steel casting process. This near-net-shape casting, although still in development, is one of the most promising routes for casting of low-carbon steel in large scale. This paper focuses on the performance of a low-Re {kappa}-{epsilon} model that was employed to simulate the three-dimensional turbulent flows fully-coupled with heat transfer and macroscopic solidification. Simulations were run for the intended conditions of caster operation, and the results obtained with the {kappa}-{epsilon} were compared with the results obtained with an ad hoc viscosity model, where the molecular viscosity was boosted 100 times, uniformly throughout the computational domain. A semi-analytical solution was employed for validating the models and the results showed that the ad hoc viscosity model overestimated the ...

2000-01-01

322

Texture development of ARB processed Mg/Al multilayers  

International Nuclear Information System (INIS)

Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong decrease of both textures, whereas Mg has always a much stronger texture than Al5052. ...

2010-07-01

323

Synthesis and characterization of #beta#-SiAlON with a rare earth concentrate as sintering aid  

International Nuclear Information System (INIS)

Silicon nitride-based ceramics behavior is strongly influenced by microstructural parameters, which, in turn are determined by chosen densification method. Highly covalent Si-N bond hind are the silicon nitride densification. Therefore, metal oxides are used in order to get high density. However, such oxides must be carefully selected, because they affect the general macroscopic properties of sintered bodies. In the present work, the viability of rare earth concentrate use to produce #beta#--Si_6_-_xAl_xO_xN_8_-_x and its effect on mechanical properties of the sintering ceramics are studied. Additive composition, heating rate, soaking time and sintering temperature were took as variables. Hardness, fracture toughness, Young's modulus and flexural strength were investigated. Lattice parameter compositional dependence and secondary phases crystallized after past-sintering heat treatment were also determined. The results show that rare earth concentrate works very ...

324

Solution of unidimensional problems from monoenergetics neutrons diffusion through finite differences  

International Nuclear Information System (INIS)

A calculation program (URA 6.F4) was elaborated on FORTRAN IV language, that through finite differences solves the unidimensional scalar Helmholtz equation, assuming only one energy group, in spherical cylindrical or plane geometry. The purpose is the determination of the flow distribution in a reactor of spherical cylindrical or plane geometry and the critical dimensions. Feeding as entrance datas to the program the geometry, diffusion coefficients and macroscopic transversals cross sections of absorption and fission for each region. The differential diffusion equation is converted with its boundary conditions, to one system of homogeneous algebraic linear equations using the box integration technique. The investigation on criticality is converted then in a succession of eigenvalue problems for the critical eigenvalue. In general, only is necessary to solve the first eigenvalue and its corresponding eigenvector, employing the power method. The obtained results by ...

1993-11-18

325

Observations of toroidal and poloidal rotation in the high-beta tokamak Torus II  

Science.gov (United States)

The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and polidal rotation in the high-beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10/sup 6/ cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal-plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10/sup 6/ cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collisional, Pfirsch-Schluter regime. The poloidal motion, however, results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the measured poloidal velocity. Mechanisms for the ...

1983-01-01

326

Observations of toroidal and poloidal rotation in the high beta tokamak Torus II  

Science.gov (United States)

The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and poloidal rotation in the high beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10/sup 6/ cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10/sup 6/ cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collosional, Pfirsch-Schluter regime. The poloidal motion, however results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the measured poloidal velocity. Mechanisms for the ...

1983-01-01

327

Microscopic analysis of the /sup 88/Sr(p,p') reaction at E/sub p/ = 201. 5 MeV  

Energy Technology Data Exchange (ETDEWEB)

Differential cross sections for 201.5 MeV proton scattering form /sup 88/Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good description is obtained for states with ...

1988-04-25

328

Microscopic analysis of the "8"8Sr(p,p') reaction at E_p = 201.5 MeV  

International Nuclear Information System (INIS)

Differential cross sections for 201.5 MeV proton scattering form "8"8Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good description is obtained for states with spins ranging ...

329

Magnetic resonance imaging in multiple sclerosis. Imagerie nouvelle par resonance magnetique nucleaire au cours de la sclerose en plaques  

Energy Technology Data Exchange (ETDEWEB)

Magnetic resonance imaging (MRI) has rapidly attained a major position among the examinations used in the diagnostic approach of multiple sclerosis because it is highly sensitive in demonstrating lesions. However, these lesional images may have several meanings, and there is the problem of distinguishing between oedema, which is said to reflect recent lesions, and gliosis which is thought to betray old lesions. The intrinsic MRI parameters studied (i.e. relaxation times) are unable to make this distinction, whereas it is provided by paramagnetic contrast media such as gadolinium. There is no correlation between the changes observed at MRI and the severity of the disease. Another problem is the accuracy of lesion localization, since visualization is predominantly macroscopic. This raises several questions about the demonstration of correlations between clinical signs and site of the lesion(s). At the moment, several teams of neuroradiologists are trying to find the ...

1991-09-15

330

Macroscopic consequences of calcium signaling in microdomains: A first passage time approach  

CERN Document Server

Calcium (Ca) plays an important role in regulating various cellular processes. In a variety of cell types, Ca signaling occurs within microdomains where channels deliver localized pulses of Ca which activate a nearby collection of Ca-sensitive receptors. The small number of channels involved ensures that the signaling process is stochastic. The aggregate response of several thousand of these microdomains yields a whole-cell response which dictates the cell behavior. Here, we study analytically the statistical properties of a population of these microdomains in response to a trigger signal. We apply these results to understand the relationship between Ca influx and Ca release in cardiac cells. In this context, we use a first passage time approach to show analytically how Ca release in the whole cell depends on the single channel kinetics of Ca channels and the properties of microdomains. Using these results, we explain the underlying mechanism for the graded relationship between Ca ...

2007-01-01

331

Influence of carbonization conditions on micro-pore structure of foundry formed coke produced with char  

Energy Technology Data Exchange (ETDEWEB)

There are few studies on coke's micro-pore structure in recent years, however, micro-pore structure of foundry coke determines its macroscopically quality index and reactivity in cupola furnace. Effect of such factors on micro-pore structure were investigated under different carbonization conditions with certain ratio of raw materials and material forming process in this article as charging temperature (A); braised furnace time (B); heating rate of the first stage (C)and the second stage (D) and holding time of ultimate temperature (E). Research showed that charging temperature was the most influential factor on the coke porosity, pore volume, pore size and specific surface area. It is suggested that formation of plastic mass and releasing rate of volatile during carbonization period are two main factors on microstructure of foundry coke while charging temperature contributes most to the above factors. 6 refs., 4 figs., 9 tabs.

2009-07-01

332

Influence of antioxidants on service life of high speed ball bearings lubrication; Einfluss von Antioxidantien auf die Schmierfettgebrauchsdauer in schnelllaufenden Waelzlagern  

Energy Technology Data Exchange (ETDEWEB)

Under severe operating conditions, such as starved lubrication, performance, service life, and reliability of rolling element bearings depend on the chemical and physical interactions between the contacting surfaces, the lubricant components, and the atmosphere. The IMKT{sup 1}, PI{sup 2}, and the imt{sup 3} have been cooperating on systematic investigations of interfacial interactions in high speed grease lubricated ball bearings. These include long time tests with complete bearings lubricated with greases of different composition under defined operating conditions, conducted at the IMKT, and chemical and physical characterizations of the running surfaces at the PI and imt. At the PI, in particular the chemical nature of the boundary layers has been investigated with time of flight secondary ion mass spectrometry (TOF-SIMS). The imt has been involved in the investigations by measuring the physical/mechanical properties of interacting surfaces at the micro/nano-scale after the removal ...

2004-07-01

333

Hardening by point defects in neutron irradiated AlN and SiC  

International Nuclear Information System (INIS)

Pressureless-sintered AlN and hot-pressed, pressureless-sintered and reaction-bonded SiC were neutron irradiated at temperatures between 100 and 785degC up to a fluence of 5.2 x 10"2"4 n/m"2. The hardness was increased by up to 51% in AlN and 84% in SiC. The hardness decreased after annealing at temperatures around the irradiation temperature. At the same temperatures, the macroscopic length, which was increased by irradiation, also began to decrease. The hardness and length were almost recovered after 1,200 #approx# 1,400degC annealing. Thus, hardening in irradiated AlN and SiC is controlled by the number of point defects, or, more precisely, by the strain caused by small point defect clusters which pin down dislocation movement. Dislocation loops were still observed in some samples after 1,400degC annealing while the hardness was almost recovered to that in the unirradiated state. Thus, the existence of dislocation loops is not grounds for hardening in irradiated ...

334

Generalized Gas Dynamic Equations for Microflows  

CERN Document Server

n an early approach, we proposed a kinetic model with multiple translational temperature [K. Xu, H. Liu and J. Jiang, Phys. Fluids {\\bf 19}, 016101 (2007)], to simulate non-equilibrium flows. In this paper, instead of using three temperatures in $x-$, $y-$, and $z$-directions, we are going to further define the translational temperature as a second-order symmetric tensor. Based on a multiple stage BGK-type collision model and the Chapman-Enskog expansion, the corresponding macroscopic gas dynamics equations in three-dimensional space will be derived. The zeroth-order expansion gives the 10 moment closure equations of Levermore [C.D. Levermore, J. Stat. Phys {\\bf 83}, pp.1021 (1996)]. To the 1st-order expansion, the derived gas dynamic equations can be considered as a regularization of Levermore's 10 moments equations. The new gas dynamic equations have the same structure as the Navier-Stokes equations, but the stress strain relationship in the Navier-Stokes ...

2008-01-01

335

Failure analysis of CO_2 anti-freezing heater at Daya Bay Nuclear Power Station  

International Nuclear Information System (INIS)

In this paper, an investigation was performed on a failure pressure vessel, which was as an anti-freezing heater for General Gas Storage and Distribution (SGZ) system. Evident and serious deformation was observed on the body of the vessel. A metallurgical investigation was conducted to establish the mechanism and cause of deformation of the anti-freezing heater at Daya Bay PWR station in China. The investigation, which was performed on specimens cut from the most serious area deformed of the vessel, included macroscopic examination and microscopy examination. The results of the examinations showed that some lamellar pearlite in the microstructure were already spheroidized. It was confirmed that the vessel was operated at high temperature. Stress analysis for the vessel was conducted. And it was confirmed that, in ideal conditions, the vessel would be deformed at around 420 C. The overall results of the investigation showed that the failure of the protected ...

2002-09-23

336

Evaluation of the mobility of an organic pollutant in triphasic conditions; Evaluation de la mobilite d'un polluant organique en conditions triphasiques  

Energy Technology Data Exchange (ETDEWEB)

Soil contamination by liquid organic pollutants represents a serious threat to phreatic ground water. These organic liquids get into the ground and migrate through the porous medium until they finally reach the aquifer. After a critical study of the literature, we listed various existing multiple displacements under three-phase conditions of a disconnected polluting phase that may or not spread over water. The aim of this thesis is to model (at pore scale level) and integrate in the pore network model the various flows that occur when three phases (gas, pollutant and air) are present in a porous medium. The porous medium is supposed completely water-wet. The polluting phase may be connected or not, and the spreading coefficient of the pollutant over water may either be positive or negative. The goal of our study is to obtain macroscopic parameters such as relative permeabilities and capillary pressure. These parameters can be then incorporated in a larger-scale ...

2006-10-15

337

Evaluation of press formability in magnesium alloy  

Energy Technology Data Exchange (ETDEWEB)

A press formability of magnesium alloy sheet cannot be evaluated by only general characteristics in tensile test; tensile strength, elongation n-value and r-value. For example, AZ31-alloy elongates about 20% in room temperature but breaks easily at shallow stage in deep drawing, which is caused by little local elongation (local necking). Crystallographic restriction of slip deformation in this alloy produces high strength, which almost equal to macroscopic fracture strength. In press forming, the bending under high tension requires a large deformability. A great difference in the deformability between AZ31 magnesium alloy and a strain hardened A1100 Aluminum (only 5% in elongation) is shown by static bending test with V-notch. In a rolled plate of AZ31, a crack is produced by stress concentration and propagates with reduced load at all testing temperature up to 453 K. In contrast, the point of notch in A1100 is dulled by local plastic deformation with held load in ...

2003-07-01

338

Evaluation of performance and characteristics of neutron radiography and standardization  

Energy Technology Data Exchange (ETDEWEB)

Neutron radiography has been put to practical use in foreign countries as one of nondestructive inspection technologies, but in Japan, its application to other scientific fields is mainly researched. The reason is, the neutron radiography apparatuses installed in Japan are hard to be industrially utilized for a number of reasons, but also the characteristics of neutron radiography are not clearly established, and it is not standardized. The part from a collimator through an object to a detector is called ``upstream``, the part of an image detector is called ``midstream``, and the part of image processing is called ``downstream``. The nonparallel property of beam, image distortion and the lack of sharpness, beam quality and the interaction of neutron beam with an object are discussed about the upstream. The intensity of neutron beam, the energy spectra, the effective total macroscopic cross section, the effective energy, the evaluation of scattered beam and ...

1995-02-01

339

Effective Dynamics, Big Bounces and Scaling Symmetry in Bianchi Type I Loop Quantum Cosmology  

CERN Document Server

The detailed formulation for loop quantum cosmology (LQC) in the Bianchi I model with a scalar massless field has been constructed. In this paper, its effective dynamics is studied in two improved strategies for implementing the LQC discreteness corrections. Both schemes show that the big bang is replaced by the big bounces, which take place up to three times, once in each diagonal direction, when the area or volume scale factor approaches the critical values in the Planck regime measured by the reference of the scalar field momentum. These two strategies give different evolutions: In one scheme, the effective dynamics is independent of the choice of the finite sized cell prescribed to make Hamiltonian finite; in the other, the effective dynamics reacts to the macroscopic scales introduced by the boundary conditions. Both schemes reveal interesting symmetries of scaling, which are reminiscent of the relational interpretation of quantum mechanics and also suggest ...

2007-01-01

340

Dislocation plasticity and complementary deformation mechanisms in polycrystalline Mg alloys  

Energy Technology Data Exchange (ETDEWEB)

Deformation mechanisms of Mg-Al-Zn (AZ31) alloys were investigated by performing tensile test at room temperature. In fine grain Mg alloys deformed at room temperature, nonbasal slip systems were found to be active as well as basal slip systems because of grain-boundary compatibility effect. Slip-induced grain-boundary sliding occurred as a complementary deformation mechanism to give rise to c-axis component of strain. With increasing grain size, the activation of the nonbasal slip systems was limited near grain boundaries. Instead of grain-boundary sliding, twinning occurred as a complementary deformation mechanism in large grained samples. Orientation analysis of twins indicated that twinning is induced by stress concentration due to the pile up of basal dislocations. The grain-size dependence on deformation mechanism was found to affect yielding behavior both microscopically and macroscopically which can influence various mechanical properties such as fatigue ...

2004-07-01

341

Consistency of the phenomenological theories of wave-type heat transport with the hydrodynamics of a phonon gas  

International Nuclear Information System (INIS)

Various phenomenological theories of wave-type heat transport, which can be interpreted as the models of an isotropic rigid heat conductor with an internal vector state variable, have been proposed in the literature with the objective to describe the second sound propagation in dielectric crystals. The aim of this paper is to analyze the relation between these phenomenological approaches and the phonon gas hydrodynamics. The four-moment phonon gas hydrodynamics based on the maximum entropy closure of the moment equations with nonlinear isotropic phonon dispersion relation is considered for this purpose. We reformulate the equations of this hydrodynamics in terms of energy and quasi-momentum as the primitive fields and subsequently demonstrate that, from the macroscopic point of view, they can be understood as describing the reference model of an isotropic rigid heat conductor with quasi-momentum playing the role of the internal vector state variable. This model is ...

2010-09-24

342

Behavior at under-film corrosion tips of Zn-Fe alloy coated steel sheets. Zn-Fe gokin mekki koban no tomakushita fushoku ni okeru fushoku sentanbu no kyodo  

Energy Technology Data Exchange (ETDEWEB)

From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and Zn content in the coating layer. 3. Zn-Fe (10-20%) alloy coating showed better durability against chlorine penetration than ...

1990-09-01

343

Attenuation data of point isotropic neutron sources up to 400MeV in water, ordinary concrete and iron  

Energy Technology Data Exchange (ETDEWEB)

A comprehensive attenuation data of dose equivalent for point isotropic monoenergetic neutron sources up to 400MeV in infinite shields of water, ordinary concrete and iron has been calculated using the ANISN-JR code and a neutron-photon multigroup macroscopic cross section HIL086R. The attenuation factors were fitted to a 4th order polynomial exponent formula, making possible to use easily for point kernel codes. Additional data in finite shielding geometry was also calculated to correct the effect due to infinite medium, giving the maximum correction of 0.23 in the region for more 400 cm distance from neutron source of 400 MeV in iron shield. Effective attenuation length for monoenergetic neutrons have been studied in detail. Subsequently, it was shown that the attenuation length was strongly dependent upon the penetration length and the Moyer`s formula using a single attenuation length brought large error into the dose estimation behind thick shields for the ...

1994-08-01

344

A mechanistic understanding of the formability of magnesium: examining the role of temperature on the deformation mechanisms  

Energy Technology Data Exchange (ETDEWEB)

The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. The experimental results suggest that an increased strain rate ...

2003-07-01

345

The oncogenic transforming potential of the passage of single ? particles through mammalian cell nuclei  

UK PubMed Central (United Kingdom)

Domestic, low-level exposure to radon gas is considered a major environmental lung-cancer hazard involving DNA damage to bronchial cells by α particles from radon progeny. At domestic exposure...Full Text Available

1999-01-05

346

Study of particles trapped by a magnetic field  

Science.gov (United States)

A new type of radiation which occurs when particles are accelerated in the field of a longitudinal wave and in a transverse magnetic field is studied. The characteristics of such spontaneous radiation are obtained, and the influence of collective effects on the radiation is analyzed. The application of the findings to the theory of free electron lasers is discussed. 8 references.

1986-01-01

348

Particle size effect on strength, failure, and shock behavior in polytetrafluoroethylene-Al-W granular composite materials  

Science.gov (United States)

The variation of metallic particle size and sample porosity significantly alters the dynamic mechanical properties of high density granular composite materials processed using a cold isostatically pressed mixture of polytetrafluoroethylene (PTFE), aluminum (Al), and tungsten (W) powders. Quasistatic and dynamic experiments are performed with identical constituent mass fractions with variations in the size of the W particles and pressing conditions. The relatively weak polymer matrix allows the strength and fracture modes of this material to be governed by the granular type behavior of agglomerated metal particles. A higher ultimate compressive strength was observed in relatively high porosity samples with small W particles compared to those with coarse W particles in all experiments. Mesoscale granular force chains of the metallic particles explain this unusual ...

2008-11-01

349

Out of Gear $10 billion particle collider hasn't smashed a thing, but scientists still have high hop  

CERN Multimedia

Out of Gear $10 billion particle collider hasn't smashed a thing, but scientists still have high hop

2009-01-01

350

Organization of Bacteriophage Tail-Like Particles in Cells of Chromobacterium violaceum  

UK PubMed Central (United Kingdom)

A strain of Chromobacterium violaceum has been isolated which produces bacteriophage tail-like particles in high numbers. The extracellular morphology and the intracellular arrangement...Full Text Available

1972-05-01

351

Numerical calculations on flow and behavior of pulverized coal and ash particles in 2-stage entrained-flow gasifier  

Energy Technology Data Exchange (ETDEWEB)

Flow fields, temperature distributions, and particle trajectories in a 2-stage entrained-flow gasifier are calculated using a CFD code, FLUENT. Realizable k- {epsilon} model is used as a turbulent model. Because of swirling flow there appear recirculation regions near the burners. The characteristics of flow fields and temperature distributions in the gasifier are dependent on the swirl number of the system. Mean residence time of the particles in the reductor is inversely proportional to particle size, particle density and swirl number. As the swirl number is increasing, the particles injected from the combustor burners approach the wall near the combustor burners, which prevents the particles from entering the reductor and thus attaching the reductor wall. If the lower combustor burner angle is larger than the higher combustor burner angle for a given swirl ...

2001-07-01

353

Multiplicity distribution of charged particles in cosmic-ray proton induced nuclear reaction  

International Nuclear Information System (INIS)

The measured result of charged multiplicity in cosmic-ray proton induced nuclear reaction from Chinese satellite emulsion is reported. The correlation of shower and heavy particles is discussed and compared with p-emulsion interactions.

1993-01-01

354

Energetic constraints on the creation of cell membrane pores by magnetic particles.  

UK PubMed Central (United Kingdom)

Naturally occurring and contaminant ferromagnetic and ferrimagnetic particles have been found within or near cells, and might allow pulsed magnetic fields to create transient cell membrane opening ("pores")....Full Text Available

1996-08-01

355

Effect of Particle Size on Compaction of Materials with Different Deformation Mechanisms with and without Lubricants  

UK PubMed Central (United Kingdom)

This work investigates the effect of excipient particle size on compaction properties of brittle, plastic and viscoelastic materials with and without added lubricants. Sieve cuts of Microcrystalline...Full Text Available

356

Dissipative particle swarm optimization  

CERN Document Server

A dissipative particle swarm optimization is developed according to the self-organization of dissipative structure. The negative entropy is introduced to construct an opening dissipative system that is far-from-equilibrium so as to driving the irreversible evolution process with better fitness. The testing of two multimodal functions indicates it improves the performance effectively

2005-01-01

357

Development program for magnetically assisted chemical separation: Evaluation of cesium removal from Hanford tank supernatant  

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma ...

1994-05-09

358

Bragg curves of fission fragments in gases  

Energy Technology Data Exchange (ETDEWEB)

An unexpectedly high probability of collisions between the fission particles and the atoms in an ionization chamber along the entire particle track causes a strong fluctuation of the shapes of the Bragg curves. This fluctuation imposes an upper limit of the charge resolution ..delta..Z/Z which can be achieved.

1986-03-01

359

Biopersistence of nonfibrous mineral particles in the respiratory tracts of subjects following occupational exposure.  

UK PubMed Central (United Kingdom)

Transmission electron microscopy analysis (TEMA) was used to analyze the bronchoalveolar lavage fluid (BALF) of 262 subjects occupationally exposed (OE) to nonfibrous mineral particles (NFMP) and 42...Full Text Available

1994-10-01

360

Bacterial Particle Endocytosis by Epithelial Cells Is Selective and Enhanced by Tumor Necrosis Factor Receptor Ligands?  

UK PubMed Central (United Kingdom)

Bacterial pathogens use virulence strategies to invade epithelial barriers, but active processes of epithelial cells may also contribute to the endocytosis of microbial particles. To focus on the latter,...Full Text Available

2009-03-01

362

A plasma process for the synthesis of cubic-shaped silicon nanocrystals for nanoelectronic devices  

International Nuclear Information System (INIS)

Low pressure silane plasmas are known for their ability to synthesize silicon nanoparticles via gas phase nucleation. While in the past this particle formation has often been considered from the viewpoint of a contamination problem in semiconductor processing, we here describe a silane low pressure plasma that enables the synthesis of highly oriented, cubic-shaped silicon nanocrystals with a rather monodisperse size distribution. These silicon nanocubes have successfully been used in the manufacture of single nanoparticle vertical transistors. We discuss the advantages of this new paradigm of building nanoelectronic devices. The plasma synthesis process is characterized in more detail than in prior work. The particle nucleation, growth and shape evolution are studied. Results indicate that the process provides two spatially distinct zones: a diffuse plasma for particle growth and a constricted plasma zone for ...

2007-04-21

363

14 - NASA  

Science.gov (United States)

... and mean rainfall rates, Rm, in the liquid hydrometeor layers using the .... large latitudinal movement of cirrus cloud cover with the changing seasons. ... We study the statistical distribution of PSCs by particle composition using .... the high resolution Cloud Particle Imager (CPI) and standard PMS 2D-C and ...

364

Versatile charged particle activation technique for the analysis of the noble metals  

Energy Technology Data Exchange (ETDEWEB)

The general usefulness of neutron activation analysis (NAA) for samples containing the platinum group elements (PGE) and Au, either as major or trace constituents, is discussed. Charged particle activation is shown to be a viable or complementary alternative. Proton (6-10 MeV) and alpha particle (9-15 MeV) beams, produced in a tandem Van de Graaff accelerator, have been established to be the most effective choice. By taking advantage of the Coulomb barrier effect and the fact that many charged particle induced reactions have relatively large threshold values, the same instrumental technique can be applied, with minor modifications, to a wide range of materials.

1982-01-01

365

Versatile charged particle activation technique for the analysis of the noble metals  

Energy Technology Data Exchange (ETDEWEB)

The general usefulness of neutron activation analysis (NAA) for samples containing the platinum group elements and Au, either as major or trace constituents, is discussed. Charged particle activation is shown to be a viable or complementary alternative. Proton (6-10 MeV) and alpha particle (9-15 MeV) beams, produced in a Tandem van de Graaff accelerator, have been established to be the most effective choice. By taking advantage of the Coulomb barrier effect and the fact that many charged particle induced reactions have relatively large threshold values, the same instrumental technique can be applied, with minor modifications, to a wide range of materials.

1983-01-01

366

V51 Knight Shift in Fine V3Si Particles  

Science.gov (United States)

The Knight shift of vanadium (KV) in fine V3Si particles was studied. The average diameter (\\bar{d}) ranged from 60 to 8000 A. The strong temperature dependence of the KV characteristic of high-Tc A-15 compounds was weakened in the particles. KV at 77 K increased with a decrease in \\bar{d}. The above-mentioned trends were consistent with a broadening of the sharp peak in the electronic density of states around the Fermi energy in particles resulting from a perturbation of the surface.

1987-12-01

367

The viscoelastic composite with interface debonding  

British Library Electronic Table of Contents (United Kingdom)

The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...

2008-01-01

368

The Pinch Technique and its Applications to Non-Abelian Gauge Theories  

CERN Document Server

Describes the Pinch Technique for constructing Green's functions for elementary particle theorists and graduate students.

2010-01-01

369

Tachyons: may they have a role in elementary particle physics  

Energy Technology Data Exchange (ETDEWEB)

The possible role of space-like objects in elementary particle physics (and in quantum mechanics) is reviewed and discussed, mainly by exploiting the explicit consequences of the peculiar relativistic mechanics of Tachyons. Particular attention is paid: (i) to tachyons as the possible carriers of interactions; (ii) to the possibility of ''vacuum decays'' at the classical level; (iii) to a Lorentz-invariant bootstrap model; (iv) to the apparent shape of the tachyonic elementary particles and its possible connection with the de Broglie wave-particle dualism. (author).

1985-01-01

371

Saturn's Recycling Rings - Cassini Solstice Mission - NASA  

Science.gov (United States)

Dec 12, 2007 ... This is an artist concept of a close-up view of Saturn's ring particles.

372

Rapid and continuous hydrothermal crystallization of metal oxide particles in supercritical water  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.

1992-04-01

373

Radionuclide particle transport, sedimentation and resuspension in the Forsmark and Laxemar coastal regions  

Energy Technology Data Exchange (ETDEWEB)

In the safety assessment of a potential repository for spent nuclear fuel, it is important to assess the consequences of a hypothetical leak of radionuclides through the seabed and into a waterborne transport phase. Radionuclides adsorbed to sediment particles may be transported great distances through the processes of sedimentation and resuspension. This study investigates the transport patterns of sediment particles of two different sizes, released in the Forsmark and Laxemar area. The results show that the closed waters around Forsmark to a higher degree makes the particles stay in the area close to the release points

2007-12-15

374

Past, present and future of elementary particle physics  

International Nuclear Information System (INIS)

The 'elementary' particle physics began in 1935, when Hideki Yukawa published his pioneering pi-meson theory, and the problem of strong interaction was finally solved 40 years later by the establishment of the Standard Model. The composite models of hadrons by the Sakata school and Sin-itiro Tomonaga's renormalization theory for quantum electrodynamics played essential roles for finding this beautiful solution. It is really surprising that it took only 40 years to solve such desperately difficult problem. The 'elementary' particle physics then split into two new fields, quark-hadron physics' and 'unified (ultimate) theory of particle physics', which are now 30 years old already. (author)

2006-12-01

375

Particle emission in hydrodynamics: a problem needing a solution  

CERN Document Server

A survey of various mechanisms for particle emission in hydrodynamics is presented. First, in the case of sudden freeze out, the problem of negative contributions in the Cooper-Frye formula and ways out are presented. Then the separate chemical and thermal freeze out scenario is described and the necessity of its inclusion in a hydrodynamical code is discussed. Finally, we show how to formulate continuous particle emission in hydrodynamics and discuss extensively its consistency with data. We point out in various cases that the interpretation of data is quite influenced by the choice of the particle emission mechanism.

2004-01-01

376

Particle Entrainment Simulator at the US Army Engineer ...  

Science.gov (United States)

... operation, experimental data reduction, and application of PES results to studies related to estuarine and coastal sediment transport problems are ...

2005-09-01

377

One-particle characteristics in problems with allowance for complex configurations  

Energy Technology Data Exchange (ETDEWEB)

A method for the determination of different ''bare'' characteristics of the one-particle motion and one-particle basis in magic nuclei is described. The method is based on separating out the mixing with phonons from the phenomenological one-particle characteristics. By means of a generalization of the procedure for localization of the mass operator, relations linking the bare and phenomenological characteristics are obtained. The radial dependence of these characteristics in finite nuclei and the influence of the quasiparticle--phonon interaction on the phenomenological characteristics are studied. Calculations are performed for the neutrons in /sup 208/Pb.

1986-09-01

378

Numerical study of Cosmic Ray Diffusion in MHD turbulence  

CERN Document Server

We study diffusion of Cosmic Rays (CRs) in turbulent magnetic fields using test particle simulations. Electromagnetic fields are produced in direct numerical MHD simulations of turbulence and used as an input for particle tracing, particle feedback on turbulence being ignored. Statistical transport coefficients from the test particle runs are compared with earlier analytical predictions. We find qualitative correspondence between them in various aspects of CR diffusion. In the incompressible case, that we consider in this paper, the dominant scattering mechanism occurs to be the non-resonant mirror interactions with the slow-mode perturbations. Perpendicular transport roughly agrees with being produced by magnetic field wandering.

2010-01-01

380

Meteorologial Techniques  

Science.gov (United States)

... 2-93 An Atmospheric Particle Emits Electromagnetic ... atmospheric water vapor produces a hydrometeor. ... subject to wind movement (either blowing ...

2003-06-13

382

High Resolution Mesoscale Weather Data Improvement to ...  

Science.gov (United States)

... that defines hydrometeor categories for the duration of the simulation ... and to observe the movement of any particular system ... particle settling occurred ...

2007-03-01

383

Evaluation of Daytime Boundary Layer Heights from a ...  

Science.gov (United States)

... the vertical beam measures the movement of the ... be measured because the particle velocity in ... During precipitation, if the hydrometeor fall velocity is ...

2008-03-01

384

Emission of light charged particles accompanying uranium fission induced by 153-MeV protons  

Energy Technology Data Exchange (ETDEWEB)

The emission of light charged particles from heavy fragments of uranium fission induced by 153-MeV protons is studied. The probability of their emission is 2.7 x 10{sup - 2} per fission event. It is found that these particles affect the distribution of angles of fragment divergence and the angular distribution of heavy fragments with respect to the primary-proton beam. Experimental results suggest that the preequilibrium emission of particles is correlated with fission. Two mechanisms of interaction between 153-MeV protons and uranium nuclei are considered. 13 refs., 10 figs., 1 tab.

1995-12-01

385

Electrical properties of airborne nanoparticles produced by a commercial spark-discharge generator  

International Nuclear Information System (INIS)

A nanoparticle generator based on the principle of electrical discharge (PALAS GFG-1000) was used to produce nanoparticles of different chemical natures. The fractions of electrically neutral particles were then measured by means of a Spectrometre de Mobilite Electrique Circulaire (SMEC, i.e. radial-flow mobility analyzer) for different operating conditions. The experimental results were compared with the theoretical values calculated from the Fuchs extended charge equilibrium model for spherical particles and agglomerates. For the smallest particles (below 20 nm), the deviations observed remain below 10%, and tend towards 20% for larger particles (over 35 nm).

2010-08-01

386

Deuteron break-up by the 27.2 MeV- alpha particle  

International Nuclear Information System (INIS)

Russian 1974. USSR Grantsev, VI Dryapachenko, IP Kornilov, VA Nemets,

1974-01-29

387

Deuteron break-up by the 27,2 MeV-alpha particle  

International Nuclear Information System (INIS)

Russian (Oct 1974). USSR Grantsev, VI Dryapachenko, IP Kornilov,

1974-01-29

389

Decontamination factors and release rates of UO/sub 2/ particles from boiling pools of sodium  

Energy Technology Data Exchange (ETDEWEB)

A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions.

1983-01-01

390

Decontamination factors and release rates of UO"2 particles from boiling pools of sodium  

International Nuclear Information System (INIS)

A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions. (orig.).

391

Decays of "8"8Kr and "8"8Rb  

International Nuclear Information System (INIS)

... isotopes minutes living radioisotopes nuclei odd-odd nuclei particle properties

392

Charged particles background due to electromagnetic processes at the VLEPP based Photon Linear Collider with ultimate luminosity  

Energy Technology Data Exchange (ETDEWEB)

We have made preliminary estimates of charged particles background at the 100x100 GeV Photon Linear Collider with ultimate luminosity. The charged particles background due to electromagnetic processes is located mainly in the small-angle range of the detector. At large angles, the number of background particles is much smaller. Analysis of the background (at least, in the range under consideration) shows that background conditions for the VLEPP-based Photon Linear Collider are better than at the VLEPP electron-positron collider. ((orig.)).

1995-02-01

394

Beam stability study based on the beam trajectory jitter in the KEKB injector linac  

International Nuclear Information System (INIS)

... Tsukuba, Ibaraki (Japan) 389 p. PARTICLE ACCELERATORS beam monitoring

2001-08-01

395

Angular distributions of light charged particles from /sup 252/Cf fission in the ranges 0-46/sup 0/ and 134-180/sup 0/  

Energy Technology Data Exchange (ETDEWEB)

Alpha particles, tritons, deuterons and protons accompanying /sup 252/Cf fission were registered in coincidence with both fission fragments by means of a system containing two-dimensional position-sensitive silicon detectors. Angular distributions, kinetic energy spectra of light charged particles as well as mass distributions of fission fragments in coincidence with light charged particles were measured. The experimental results are compared with some theoretical models.

1985-06-03

396

Analytic description of X-ray fluorescence intensity as a function of the particle size in powder samples and pulp upon X-ray fluorescence analysis  

International Nuclear Information System (INIS)

Analytic expression is derived for X-ray fluorescence dependence on the particle size of powder and slurry media. The expression is obtained for a model of powder medium containing particles of different size and random distribution in the bulk of the sample. Limiting cases of homogeneous and slurry-like media are considered and expressions for calculation of the fluorescence intensity are derived. The results reasonably match the experiment for binary powder mixtures and thus provide evaluation of the powder particle size on the fluorescence intensity for multicomponent polydisperse powder medium

2007-11-01

398

A multiple sampling proportional counter for particle identification of relativistic heavy ions  

Energy Technology Data Exchange (ETDEWEB)

A multiple sampling dE/dx counter using a multiwire proportional chamber equipped with catbode pads was constructed for the multiple detection of dE/dx values along a particle trajectory. For low-energy particles this counter was proved to be useful as a Bragg-curve detector. At relativistic energies around E=14.6 GeV/nucleon good particle identification was obtained by cathode pad signals as well as anode signals for the range of projectile fragments from Z=1 (minimum ionization) up to a beam charge of Z=14. (orig.).

1990-11-15

399

Test particle moving in an interior static spherically symmetric geometry  

Energy Technology Data Exchange (ETDEWEB)

The motion of a test particle moving in an interior static spherically symmetric geometry is investigated. The author concludes that an oscillatory motion with the test particle changing its motion from a free fall towards the center to an outward radial motion can not exist for any static interior spherically symmetric model.

1984-06-01

400

Spiral modes in the diffusion of a single granular particle on a vibrating surface  

International Nuclear Information System (INIS)

We consider a particle that is subject to a constant force and scatters inelastically on a vibrating periodically corrugated floor. At small friction and for small scatterers the dynamics is dominated by resonances forming spiral structures in phase space. These spiral modes lead to pronounced maxima and minima in the diffusion coefficient as a function of the vibration frequency, as is shown in computer simulations. Our theoretical predictions may be verified experimentally by studying transport of single granular particles on vibratory conveyors.

2004-11-29

401

Spinning tachyons as particle constituents  

International Nuclear Information System (INIS)

The motions of a classical free spinning point particle are extended to include the range of superluminal velocities. There is no formal change in the constraint-dependent functional relationship between observable mass and spin, i.e., trajectory, accompanying this extension. However, the theory now permits the specification, for superluminal velocities, of a linearly rising trajectory and naturally yields tachyon confinement. Therefore, unlike their subluminal counterparts, these tachyons can be considered candidates for elementary particle constituents.

402

Production of cumulative hadrons in quark models of flucton fragmentation  

International Nuclear Information System (INIS)

Quark models of production of cumulative particles and the EMC effect are analyzed. It is shown that all these models are characterized by a universal relation between the spectrum of cumulative nucleons and the cross section for cumulative particles containing valence quarks of the nucleus. This relation is tested for the deuteron, and the role of secondary nuclear processes for heavy nuclei is discussed. It is noted that the ''sea'' cumulative particles (K"-, p-bar) are particularly important for understanding the nature of the difference between the structure functions of a nucleus and of a free nucleon.

403

Particle identification through the measurement of the Bragg curve centroid  

Energy Technology Data Exchange (ETDEWEB)

A new method of particle identification of heavy ions through the measurement of the Bragg curve centroid and particle energy has been developed using a gas ionization chamber with a resistive anode layer. Z-resolutions comparable to the conventional ..delta..E-E counter telescope could be rather easily attained.

1983-07-01

404

Particle identification through the measurement of the Bragg curve centroid  

International Nuclear Information System (INIS)

A new method of particle identification of heavy ions through the measurement of the Bragg curve centroid and particle energy has been developed using a gas ionization chamber with a resistive anode layer. Z-resolutions comparable to the conventional #DELTA#E-E counter telescope could be rather easily attained. (orig.).

405

Optimizing semiconductor devices by self-organizing particle swarm  

CERN Document Server

A self-organizing particle swarm is presented. It works in dissipative state by employing the small inertia weight, according to experimental analysis on a simplified model, which with fast convergence. Then by recognizing and replacing inactive particles according to the process deviation information of device parameters, the fluctuation is introduced so as to driving the irreversible evolution process with better fitness. The testing on benchmark functions and an application example for device optimization with designed fitness function indicates it improves the performance effectively.

2005-01-01

406

Improved Conservation Properties for Particle-in-cell Simulations with Kinetic Electrons  

Energy Technology Data Exchange (ETDEWEB)

It is shown that a simple algorithm which exactly segregates between adiabatic and non-adiabatic electrons in particle-in-cell simulations of drift modes yields excellent conservation properties (e.g. particle number, energy) compared to the conventional df scheme. The removal of the free streaming term in the evolution of the marker weight is shown to be responsible for the improved linear and nonlinear properties of the simulated plasma.

2003-06-19

407

Hot Particles Research for Nuclear Power Plant in Wolsung  

Energy Technology Data Exchange (ETDEWEB)

The evaluation of the hazard posed to the skin by very small radioactive sources (diameter < 1mm) has become popularly known as the 'hot particle' problem in European and American nuclear reactor facilities. In this study, research to detect hot particle was performed in Wolsung Nuclear power plant (NPP) in Korea.

2007-10-15

408

Hot Particles Research for Nuclear Power Plant in Wolsung  

International Nuclear Information System (INIS)

The evaluation of the hazard posed to the skin by very small radioactive sources (diameter < 1mm) has become popularly known as the 'hot particle' problem in European and American nuclear reactor facilities. In this study, research to detect hot particle was performed in Wolsung Nuclear power plant (NPP) in Korea.

2007-10-01

409

Formation of nano-sized particles of a solid electrolyte by laser ablation  

Energy Technology Data Exchange (ETDEWEB)

Nano-sized particles of a lithium ion conductive solid electrolyte, LiTi{sub 2}(PO{sub 4}){sub 3}, were prepared by laser ablation. The obtained particles were ca. 10nm in diameter. X-ray powder diffraction and Raman spectroscopy showed that they were amorphous with local structure similar to the crystalline counterpart. They were crystallized by the heating at ca. 630{sup o}C. (author)

2005-08-26

410

Explicit equation for particle settling velocities in solid-liquid systems  

Energy Technology Data Exchange (ETDEWEB)

Zanker has recently presented nomographs for determining particle settling velocities in solid-liquid systems. These nomographs were based on the general correlations developed by Barnea and Mizrahi and Barnea and Mednick. This work presents an equation directly computing particle settling velocities, eliminating the uncertainty associated with nomographs.

1981-11-01

411

Experimental and evaluated nuclear plus interference cross sections for light charged particles  

Energy Technology Data Exchange (ETDEWEB)

Experimental and evaluated integral parameters derived from nuclear plus interference differential elastic scattering cross sections are presented for all projectile/target combinations of the particles p, d, t, /sup 3/He, and ..cap alpha... The data include reaction rates, average fractional energy losses per collision and per unit path length, and average laboratory scattering cosines. The resulting parameters are of potential use in analysis of charged-particle transport.

1980-07-04

412

Effect of WC particle size on grain growth inhibition in the WC-xVC-Co system  

Energy Technology Data Exchange (ETDEWEB)

The effect of WC particle size with the addition of VC as a grain growth inhibitor was investigated during the liquid phase sintering of WC-Co system. With increasing WC particle size at the same VC content, the effect of grain growth inhibition was increased. Also, with increasing the VC content, the grain shape of WC was changed from the faceted shape to the distorted shape, and the step density of the WC grain was increased. (orig.)

2003-07-01

413

Direct conversion of fusion energy into the electric one in the 'Dragon' magnetic confinement system  

International Nuclear Information System (INIS)

It is shown that recuperator in which the thermal energy of particles is transformed into electric oue under drift in crossed fields is naturally coupled with dragontype magnetic confinement system, so the recuperation process can be initiated in the dragon magnetic field. A number of questions occuring under analysis of recuperator-dragon system is considered, including the dynamics of particle transfer to the recuperator, the share of particles entering the recuperator, the effect of rotational transform and the recuperation efficiency.

414

Deposition and removal of sub-micron particles of magnetite at the surface of alloy 800. AECL research No. AECL-11015  

Energy Technology Data Exchange (ETDEWEB)

This report measured the rate of isothermal deposition of sub-micron particles of magnetite onto the surface of Alloy 800 at pH of 4.2-9.3 at Re=10,000 and a fluid temperature of 25C. Deposition is modelled as a two-step process, the transport of particles to the surface region followed by attachment to the surface.

1994-12-31

415

Cumulative hadron production in quark models of flucton fragmentation  

International Nuclear Information System (INIS)

Quark models of cumulative particle production and EMS effect are analyzed. All the models are characterized by a universal relationship between the spectrum of cumulative nucleons and the cross section of cumulative particles containing valence nuclear quarks. This relationship is tested for a deuteron. The role is discussed played by secondary nuclear processes for heavy nuclei. A special role of ''sea'' cumulative particles (K"-, p-bar) is pointed out in understanding the nature of the difference between the structure functions of a nucleus and of free nucleon.

416

Coincidence study of alpha particle fragmentation at E/sub alpha/ = 140 MeV  

Energy Technology Data Exchange (ETDEWEB)

Results of an experimental study of the interaction of 140 MeV alpha particles with /sup 90/Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from /sup 90/Zr(..cap alpha..,pp)X reactions, where both of the measured protons have energy ...

1980-01-01

417

Coincidence study of alpha particle fragmentation at E/sub alpha/ = 140 MeV  

International Nuclear Information System (INIS)

Results of an experimental study of the interaction of 140 MeV alpha particles with _9_0Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from _9_0Zr(#alpha#,pp)X reactions, where both of the measured protons have energy distributions ...

418

Cleavage of tRNA within the mature tRNA sequence by the catalytic RNA of RNase P: implication for the formation of the primer tRNA fragment for reverse transcription in copia retrovirus-like particles.  

UK PubMed Central (United Kingdom)

The retrovirus-like particles of Drosophila are intermediates of retrotransposition of the transposable element copia. In these particles, a 39-nucleotide-long fragment from the 5' region of Drosophila...Full Text Available

1990-10-01

419

Battery using a metal particle bed electrode  

Energy Technology Data Exchange (ETDEWEB)

A zinc-air battery in a case including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit.

1991-01-01

420

Battery using a metal particle bed electrode  

Energy Technology Data Exchange (ETDEWEB)

A zinc-air battery in a case is described including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit. 7 figures.

1991-04-09

421

Alfven Eigenmode Stability with Beams in ITER-like Plasma  

Energy Technology Data Exchange (ETDEWEB)

Toroidicity Alfven Eigenmodes (TAE) in ITER can be driven unstable by two groups of energetic particles, the 3.5 MeV {alpha}-particle fusion products and the tangentially injected 1MeV beam ions. Stability conditions are established using the perturbative NOVA/NOVA-K codes. A quasi-linear diffusion model is then used to assess the induced redistribution of energetic particles.

2004-07-16

422

Response surface characterization of impact damage and residual strength degradation in composite sandwich panels  

Science.gov (United States)

The influence of material configuration and impact parameters on the damage tolerance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based response surfaces. A series of carefully selected tests were used to isolate the coupled influence of various combinations of the number of facesheet plies, core density, core thickness, impact energy, impactor diameter, and impact velocity on the damage formation and residual strength degradation due to normal impact. The ranges of selected material parameters were typical of those found in common aircraft applications. The diameter of the planar damage area associated with Through Transmission Ultrasonic C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. ...

2003-01-01

423

ISDD: A Computational Model of Particle Sedimentation, Diffusion and Target Cell Dosimetry for In Vitro Toxicity Studies  

Energy Technology Data Exchange (ETDEWEB)

Background: The difficulty of directly measuring cellular dose is a significant obstacle to application of target tissue dosimetry for nanoparticle and microparticle toxicity assessment. As a consequence, the target tissue paradigm for dosimetry and hazard assessment of nanoparticles has largely been ignored in favor of using metrics of exposure (e.g. ?g particle/mL culture medium, particle surface area/mL, particle number/mL). We have developed a computational model of solution particokinetics (sedimentation, diffusion) and dosimetry for non-interacting spherical particles and their agglomerates in monolayer cell culture systems. Particle transport to cells is calculated by simultaneous solution of Stokes Law (sedimentation) and the Stokes-Einstein equation (diffusion). Results: The In vitro Sedimentation, Diffusion and Dosimetry model (ISDD) was tested against measured transport ...

2010-11-30

424

[Destruction of radioactive particles by strains of Cladosporium cladosporoides (FRES.) de Vries].  

Science.gov (United States)

Reactions on the ionizing radiation of 14 Cladosporium cladosporioides strains were studied. Only 5 of them displayed radiotropizm. The ability of C. cladosporioides strains 4 and 5 with positive radiotropizm and museum C. cladosporioides strain 396 and its alb-mutant SM without positive radiotropizm to destruct radioactive particles of Chernobyl and explosion origin was studied. Two ways of radioactive particles destruction by C. cladosporioides were established, one of them is a direct way by fungal overgrowth of hot particles and the second one an indirect way only by fungal metabolites. Mycelium of the studied C. cladosporioides strains sorbed radionuclides from radioactive particles during cultivation on the liquid and agarized media. No certain inclinations of the individual strains to accumulation of radionuclides 137Cs or 152Eu were ascertained. PMID:12664550

425

Unified semi-microscopic description of low-energy proton and. alpha. -particle scattering by nuclei  

Energy Technology Data Exchange (ETDEWEB)

We develop the formalism of a unified semi-microscopic description of low-energy proton and {alpha}-particle interaction with nuclei. We analyze elastic and inelastic proton scattering at the energy 25.05 MeV and {alpha}-particle scattering at the energy 104 MeV by the {sup 90}Zr nucleus. Information is obtained on differences in the deformation of the proton and neutron distributions. We study the energy dependence of the semi-microscopic {alpha}-particle potential including the energy dependence of the potential geometry.'' We analyze the change in angular distributions of elastically scattered {alpha} particles with increase of energy and the contribution to the scattering cross section from nucleon-nucleon correlations.

1989-07-01

426

Three-dimensional, three-component wall-PIV  

Energy Technology Data Exchange (ETDEWEB)

This paper describes a new time-resolved three-dimensional, three-component (3D-3C) measurement technique called wall-PIV. It was developed to assess near wall flow fields and shear rates near non-planar surfaces. The method is based on light absorption according to Beer-Lambert's law. The fluid containing a molecular dye and seeded with buoyant particles is illuminated by a monochromatic, diffuse light. Due to the dye, the depth of view is limited to the near wall layer. The three-dimensional particle positions can be reconstructed by the intensities of the particle's projection on an image sensor. The flow estimation is performed by a new algorithm, based on learned particle trajectories. Possible sources of measurement errors related to the wall-PIV technique are analyzed. The accuracy analysis was based on single particle experiments and a three-dimensional ...

2010-06-15

427

Self-consistent calculations within the Green's function method including particle-phonon coupling and the single-particle continuum  

Energy Technology Data Exchange (ETDEWEB)

The Green's function method in the Quasiparticle Time Blocking Approximation is applied to nuclear excitations in {sup 132}Sn and {sup 208}Pb. The calculations are performed self-consistently using a Skyrme interaction. The method combines the conventional RPA with an exact single-particle continuum treatment and considers in a consistent way the particle-phonon coupling. We reproduce not only the experimental values of low-and high-lying collective states but we also obtain fair agreement with the data of non-collective low-lying states that are strongly influenced by the particle-phonon coupling. (orig.)

2008-09-15

428

Radiation electromagnetic effect in germanium crystals under high-energy #alpha#-particle irradiation  

International Nuclear Information System (INIS)

Results of experimental investigation into radiation electromagnetic effect (REM) in samples of germanium crystals under approximately 40 MeV #alpha#-particle irradiation in a cyclotron are presented. A high level of excitation, volumetric character of generation of non-equilibrium carriers and formation of defects as well as the form of their spatial distribution are shown to result in some peculiarities of the EMF of the REM effect on the particle flux, fluence and sample parameters. Agreement of theoretical calculations, conducted with account of specificity of #alpha#-particle interaction with a crystal, and experimental data is obtained. It is revealed that the REM effect can be applied in obtaining data on spatial distribution of non-equilibrium carrier concentrations along the particle trajectory in the crystal.

429

Many-particle confinement by constructed disorder and quantum computing  

Energy Technology Data Exchange (ETDEWEB)

Many-particle confinement (localization) is studied for a 1D system of spinless fermions with nearest-neighbour hopping and interaction, or equivalently, for an anisotropic Heisenberg spin-1/2 chain. This system is frequently used to model quantum computers with perpetually coupled qubits. We construct a bounded sequence of site energies that leads to strong single-particle confinement of all states on individual sites. We show that this sequence also leads to a confinement of all many-particle states in an infinite system for a time that scales as a high power of the reciprocal hopping integral. The confinement is achieved for strong interaction between the particles while keeping the overall bandwidth of site energies comparatively small. The results show the viability of quantum computing with time-independent qubit coupling.

2005-10-01

430

Kinetic behavior of solid particle in chemical-looping combustion: suppressing carbon deposition in reduction  

Energy Technology Data Exchange (ETDEWEB)

In order to apply chemical-looping combustion to a practical power plant, carbon deposition on the solid particle is one of the key problems to be overcome. Six kinds of solid particles were examined to clarify the kinetic behavior of carbon deposition. The effects of the solid composition, feed gas composition, and reaction temperature on carbon deposition were investigated by thermogravimetrical reactor on the basis of NiO/YSZ particle. From the viewpoints of both reactivity and resistance against carbon deposition, the particle of NiO mixed with YSZ (i.e., yttria-stabilized zirconia) was found to be a good candidate for chemical-looping combustion. It has been observed that carbon deposition could be completely avoided with very low concentration of water vapor. By means of a proposed model, the condition that carbon deposition would be avoided was identified. 12 refs., 8 figs., 2 tabs.

1998-03-01

431

Extraction of biologic particles by pumping effect in a p-shaped ultrasonic actuator  

British Library Electronic Table of Contents (United Kingdom)

This paper presents a new method of extracting biologic particles from a mixture of particles. The method is based on the pumping effect in a p-shaped ultrasonic actuator, which has a gap between its two vibrating metal plates. An adhesive tape is placed at a proper position in the gap. Due to the pumping effect which is induced by the sound field in the gap, the particles with smaller mass and radius in the mixture can be pumped up to reach the adhesive tape; while the ones with larger mass cannot. Therefore, the particles with smaller mass and radius can be extracted from the mixture. A theoretical model which can well explain the operation principle and experimental phenomena is developed. By the experimental results and the theoretical analyses based on the model, the validity of the m...

2006-01-01

432

Effects of surfaces and leachables on the stability of biopharmaceuticals  

British Library Electronic Table of Contents (United Kingdom)

Abstract Therapeutic proteins are exposed to various potential contact surfaces, particles, and leachables during manufacturing, shipping, storage, and delivery. In this review, we present published examples of interfacial- or leachable-induced aggregation or particle formation, and discuss the mitigation strategies that were successfully utilized. Adsorption to interfaces or interactions with leachables and/or particles in some cases has been reported to cause protein aggregation or particle formation. Identification of the cause(s) of particle formation involving minute amounts of protein over extended periods of time can be challenging. Various formulation strategies such as addition of a nonionic surfactant (e.g., polysorbate) have been demonstrated to effectively mitigate adsorption-i...

2011-01-01

433

Direct observation of polymerization in the oleic acid-ozone heterogeneous reaction system by photoelectron resonance capture ionization aerosol mass spectrometry  

British Library Electronic Table of Contents (United Kingdom)

High molecular weight products of the ozonolysis reaction of particle-phase 9-octadecenoic acid (oleic acid) have been studied by photoelectron resonance capture ionization (PERCI) mass spectrometry (MS). Oleic acid particles ( Formula Not Shown , Formula Not Shown ) were reacted with ozone (1.8x10-4atm) in a flow reactor at reaction times of 8 and 23s. Particles were sampled on-line with a differentially pumped particle inlet and chemically analyzed by PERCI-MS. PERCI is a soft ionization method that permits the direct measurement of relatively high molecular weight compounds, facilitating molecular identification. In addition to cyclic oxygenates, such as secondary ozonides and geminal diperoxides that were reported previously, we demonstrate the formation of polymers at the particle sur...

2006-01-01

434

Coupling of magnetostriction and electrostriction in the porous rheological composite  

Energy Technology Data Exchange (ETDEWEB)

The production method of the elastic composite containing ferrous particles and titanium barium particles dispersed in the porous silicone matrix is described in this article. Since it contains ferrous and titanium barium particles, this composite shows magnetorheological and also electrorheological properties. The electrostriction of composite samples in the electric field with maximal intensity 1.5x10{sup 6} V/m was investigated. The magnetostriction in the magnetic field with maximal induction 1 T was also investigated. It was found that samples elongate with increased electric field intensity, and the magnetic field induction was detected. By increasing the samples' elongation with increase of ferrous particles, titanium barium particles and pores number were also detected. In the investigated division of the electric and magnetic field the elongation changed in a ...

2008-08-15

435

Coenzyme Q10 nanoparticles prepared by a supercritical fluid-based method  

British Library Electronic Table of Contents (United Kingdom)

A supercritical fluid-based method is proposed to produce coenzyme Q10 (CoQ10) nanoparticles. First, CoQ10/polyethylene glycol 6000 composite particles are prepared by a modified PGSS (particles from gas-saturated solutions) process with controlling the flow rate of the gas-saturated solution. Then, CoQ10 nanoparticles are obtained by dissolving the composite particles into water. The effect of experimental variables of the modified PGSS process, including pressure, temperature, flow rate of the gas-saturated solution, and mass fraction of CoQ10, on the CoQ10 particle size and particle size distribution was investigated. Results show that CoQ10 slurry product with a median diameter of 190nm and yield of 89.8% can be prepared at an optimum condition (operating pressure of 25MPa, operating t...

2011-01-01

436

Chemical transformations of peptide containing fine particles: oxidative processing, accretion reactions and implications to the atmospheric fate of cell-derived materials in organic aerosol  

British Library Electronic Table of Contents (United Kingdom)

The atmospheric processing by ozone of peptide-containing mixed particles was investigated as proxies for biogenic and sea spray primary organic aerosol. Reactions were performed in a flow reactor and particle composition was monitored by photoelectron resonance capture ionization aerosol mass spectrometry. Mixed particles containing dipeptides in a saturated organic matrix of stearic and palmitic acids showed no reaction under ozonolysis at exposure levels of 2.5???10?4?atm s O3. However reactions of mixed particles of a dipeptide (Leu-Leu) in an unsaturated matrix (oleic acid) under the same conditions resulted in a rapid loss of the peptide ion signal, as well as the carrier matrix, and appearance of a number of ion signals corresponding to secondary products. High molecular weight imid...

2009-01-01

437

Asymmetry effect of particle size distribution on content uniformity and over-potency risk in low-dose solid drugs  

British Library Electronic Table of Contents (United Kingdom)

Most active pharmaceutical ingredients (API) exhibit particle size distributions with some degrees of asymmetry deviating from log-normality. A new log-skew-normal (L-S-N) distribution model is proposed for a systematic comparison of the asymmetry effect on content uniformity. The new model originated from the S-N model used by Azzalini gives a close approximation to real API particle size distribution. Monte-Carlo method was employed to simulate the dosage potency distribution. A high risk of over potency is uncovered when either the dose is low or API particle size distribution is positively skewed. This is due to the formation of pseudo heavy tail in potency distribution that decays slower than exponentially. Nomographs of API particle size versus dosage strength were constructed with a...

2010-01-01

438

Analysis of mixing in a Twin Cam mixer using smoothed particle hydrodynamics  

British Library Electronic Table of Contents (United Kingdom)

Smoothed Particle Hydrodynamics (SPH) is a Lagrangian, particle-based method that is well suited to industrial mixing simulations. Mass transport is simply the motion of the particles, and its grid-free nature means that it can easily accommodate complicated geometries involving moving parts and sharp corners. This article describes 2D SPH simulations of a Twin Cam mixer and compares the results against experimental data and results from two published finite element method (FEM) simulations. To analyze the mixing processes in the Twin Cam mixer, we present a method for calculating the Finite-Time Lyapunov Exponent (FTLE) using SPH particle data. The FTLEs can be used to locate the unstable and stable manifolds in the flow and indicate where mixing is either promoted or inhibited in the flo...

2008-01-01

439

Alpha energy distribution as a probe for the feeding of ND and SD bands in {sup 151,152}Dy nuclei  

Energy Technology Data Exchange (ETDEWEB)

The study of the {alpha}-particle energy distributions associated with ND and SD states in {sup 151,152}Dy has been carried out. The Dy isotopes were produced in the reaction {sup 37}Cl+{sup 123}Sb at 191 MeV via the ({alpha}5n) and ({alpha}4n) channels, respectively. In {sup 151}Dy the {alpha}-particle energy distributions associated to ND and SD are very different from each other, both at the low and high energy sides inducing a difference of 3 MeV in the {alpha}-particle mean energy. In {sup 152}Dy the situation is different; the {alpha}-particle spectral shapes are similar and a difference in the {alpha}-particle mean energy of only 0.7 MeV is deduced. A description in terms of energy localization of entry states is given. (orig.)

1999-10-01

440

A particle tracking transport method for the simulation of resident and flux-averaged concentration of solute plumes in groundwater models  

British Library Electronic Table of Contents (United Kingdom)

A new numerical technique called the convolution-based particle tracking (CBPT) method is developed to simulate resident or flux-averaged solute concentrations in groundwater models. The method is valid for steady-state flow and linear transport processes such as sorption with a linear sorption isotherm and first-order decay. The CBPT method uses particle tracking to take advantage of the ability of particle-based approaches to maintain sharp fronts for advection-dominated transport problems common in groundwater modeling and because of the flexibility of the random walk method to simulate a wide range of possible forms of the dispersion tensor. Furthermore, the algorithm for carrying out the convolution and superposition calculation from particle tracking results is very efficient. We sho...

2010-01-01

441

A Neuro-Fuzzy Multi Swarm FastSLAM Framework  

CERN Document Server

FastSLAM is a framework for simultaneous localization using a Rao-Blackwellized particle filter. In FastSLAM, particle filter is used for the mobile robot pose (position and orientation) estimation, and an Extended Kalman Filter (EKF) is used for the feature location's estimation. However, FastSLAM degenerates over time. This degeneracy is due to the fact that a particle set estimating the pose of the robot loses its diversity. One of the main reasons for loosing particle diversity in FastSLAM is sample impoverishment. It occurs when likelihood lies in the tail of the proposal distribution. In this case, most of particle weights are insignificant. Another problem of FastSLAM relates to the design of an extended Kalman filter for landmark position's estimation. The performance of the EKF and the quality of the estimation depends heavily on correct a priori knowledge of the process ...

2010-01-01

442

Piping response testing associated with pipe rupture  

Energy Technology Data Exchange (ETDEWEB)

EPRI has sponsored an experimental program in the pipe whip impact and pipe rupture and depressurization areas. Sixteen pipe whip tests were performed with 3 in Schedule 80 (or 10) carbon steel pipes impacting on rigid target or concrete slab. The major testing parameters include distance, impact location, pipe rupture location, and concrete slab thickness and strength. The piping crushing at impact correlates with impact force and target response behavior. Conservatism was established by comparing measured and calculated impact forces. The pipe rupture and depressurization tests were carried out using 6 in stainless steel and carbon steel pipes under either PWR or BWR fluid conditions. These tests are of axial crack with initial machined-in surface flaw. It was found that pipe rupture would occur only if a long unstable through-wall crack was embedded in a ...

1985-11-01

443

Environmental impacts of nuclear and coal-fired power plants  

International Nuclear Information System (INIS)

The current situation in the development of nuclear power in the world and in Czechoslovakia is briefly outlined and the possibilities are discussed of alternative energy resources. The environmental impact is described of conventional power plants firing coal; sulphur and nitrogen oxides are mentioned and their environmental impacts shown. Their quantities and the quantities of other gaseous, liquid and soid wastes produced by coal power plants are given. Annual estimates are presented of radioactive material emissions; trace amount emissions of toxic metals and their ecological risks are shown. Concern over the increasing concentration of CO_2 in the atmosphere is voiced. For nuclear power plants, the amount of radionuclides in stack emission and of those released into water flows is tabulated. Their effect on the aqueous ecosystem is characterized as is thermal pollution of water flows and the environmental impact of ...

1984-01-01

444

Application of continuous wavelet transform to the impact location estimation of the Loose Parts Monitoring System (LPMS)  

International Nuclear Information System (INIS)

The Loose Parts Monitoring System (LPMS) provides information on the location of a loosened or detached metal impacted onto the inner surface of a primary pressure boundary and on a mass or energy of the impact signal. For the conventional system, it is popular to employ the group delay among the sensors installed within 3 ft range from the impact source in a collection zone as stated in the Reg. Guide 1.133. However, there exist inherent errors for the estimation of the true location of the impact since it is highly dependent on the plant personnel's decision to determine the arrival time differences of the generated wave group among the neighbouring sensors. To overcome this problem in this study, the two-dimensional approach has been proposed and applied to effectively estimate the arrival time differences of the impact signal by using continuous wavelet transform which is one of ...

445

A constitutive model for layered wire mesh and aramid cloth fabric  

Energy Technology Data Exchange (ETDEWEB)

A new package for the air transport of hazardous materials is currently being developed in the Transportation Systems Department at Sandia National Laboratories. The baseline design has a unique impact limiter which uses layers of aluminum screen wire and aramid cloth fabric. A primary motivation for selecting this unusual combination of materials is the need for the impact limiter to not only limit the amount of load transmitted to the primary container but also remain in place during impact events so that it provides a thermal barrier during a subsequent fire. A series of uniaxial and confined compression tests indicated that the layered material does not behave like other well characterized materials. No existing constitutive models were able to satisfactorily capture the behavior of the layered material; thus, a new plasticity model was developed. The new material model was then used to characterize the response of air ...

1993-09-01

446

Alpha particle destabilization of the toroidicity-induced Alfven eigenmodes  

Energy Technology Data Exchange (ETDEWEB)

The high frequency, low mode number toroidicity-induced Alfven eigenmodes (TAE) are shown to be driven unstable by the circulating and/or trapped {alpha}-particles through the wave-particle resonances. Satisfying the resonance condition requires that the {alpha}-particle birth speed v{sub {alpha}} {ge} v{sub A}/2{vert bar}m-nq{vert bar}, where v{sub A} is the Alfven speed, m is the poloidal model number, and n is the toroidal mode number. To destabilize the TAE modes, the inverse Landau damping associated with the {alpha}-particle pressure gradient free energy must overcome the velocity space Landau damping due to both the {alpha}-particles and the core electrons and ions. The growth rate was studied analytically with a perturbative formula derived from the quadratic dispersion relation, and numerically with the aid of the NOVA-K code. Stability criteria in terms of the ...

1990-10-01

447

Wastes behavior and environmental impacts, researches and methods; Comportement des dechets et impacts environnementaux, recherches et methodes  

Energy Technology Data Exchange (ETDEWEB)

The wastes management policy takes into account more and more often the environmental impacts mastership. This evolution is particularly appreciable when the wastes directly interact with the environment: storage, utilization for roads construction and so on. In this context the ADEME organized the 8 june 2000 a colloquium to present the new evaluation methods and tools, to describe the regulations and to identify the research programs needed for this environmental policy. Eleven papers are presented. (A.L.B.)

2001-07-01

448

Pipe whip: a summary of the damage observed in BNL pipe-on-pipe impact tests  

Energy Technology Data Exchange (ETDEWEB)

This paper describes examples of the damage resulting from the impact of a whipping pipe on a nearby pressurised pipe. The work is a by-product of a study of the motion of a whipping pipe. The tests were conducted with small-diameter pipes mounted in rigid supports and hence the results are not directly applicable to large-scale plant applications where flexible support mountings are employed. The results illustrate the influence of whipping pipe energy, impact position and support type on the damage sustained by the target pipe.

1987-01-01

449

Pipe whip: a summary of the damage observed in BNL pipe-on-pipe impact tests  

International Nuclear Information System (INIS)

This paper describes examples of the damage resulting from the impact of a whipping pipe on a nearby pressurised pipe. The work is a by-product of a study of the motion of a whipping pipe. The tests were conducted with small-diameter pipes mounted in rigid supports and hence the results are not directly applicable to large-scale plant applications where flexible support mountings are employed. The results illustrate the influence of whipping pipe energy, impact position and support type on the damage sustained by the target pipe. (author).

450

Modeling Blast and High-Velocity Impact of Composite Sandwich Panels  

Science.gov (United States)

Analytical models for predicting the deformation and failure of composite sandwich panels subjected to blast and projectile impact loading are presented in this paper. The analytical predictions of the transient deformations and damage initiation in the composite sandwich panels were compared with finite element solutions using ABAQUS Explicit. For the blast model, the predicted transient deformation of the sandwich panel was within 7%of FEA results, while the predicted damage initiation using Hashin's composite failure criteria was about 15%higher than FEA results in most cases. For the high velocity impact model, the predicted transient deformations were within 20%of FEA results.

2009-01-01

451

Mechanical properties of joints welded in halogen-containing controlled atmosphere  

International Nuclear Information System (INIS)

Studied are the mechanical properties of welded joints and heat affected zones of the Kh8N10T steel and OT4 and VT1-2 titanium alloys on welding in Ar+deltaF_6 and Ar+CCl_2F_2 mixtures contributed to a decrease of porosity. Tensile and impact tests of welded joints have revealed that additions of sulfur hexafluoride into argon causes a decrease of impact strength in titanium alloy when the tensile strength does not depend on the composition of a halogen-containing atmosphere. Freon (CCl_2F_2) additions decrease only slightly the impact strength of the investigated alloys.

452

Global impacts of human mineral malnutrition  

British Library Electronic Table of Contents (United Kingdom)

Malnutrition?in the form of insufficient energy intakes?affects millions of people worldwide and the negative impact of this kind of hunger is well acknowledged, not least by agronomists trying to increase yields to ensure a sufficient supply of food. This review focuses on another, more particular and ?hidden? form of malnutrition, namely mineral malnutrition. It illustrates the burden of disease that is caused by mineral deficiencies and the social and economic consequences they bring about. Mineral malnutrition has a considerable negative impact on individual well-being, social welfare and economic productivity. Agricultural scientists should keep the nutritional qualities of food in mind and?next to optimizing the agricultural properties of crops that are paramount for their adoption b...

2010-01-01

453

Photochemistry on surfaces. 2. Intermolecular electron transfer on colloidal alumina-coated silica particles  

Energy Technology Data Exchange (ETDEWEB)

Reductive quenching of two photoexcited ruthenium(II) complexes by an anionic electron donor, 2,2{prime}-azinobis(3-ethyl-benzothiazoline-6-sulfonate) (ABTS{sup 2{minus}}), in aqueous solution was examined by laser flash photolysis before and after adding positively charged colloidal (250-{angstrom} diameter) alumina-coated silica particles. The kinetics and quantum yields of electron transfer with an anionic sensitizer, RuL{sub 3}{sup 4{minus}} (L = bathophenanthroline disulfonate), and a cationic one, Ru(bpy){sub 3}{sup 2+} (bpy = 2,2{prime}-bipyridine), were compared. Coadsorption of ABTS{sup 2{minus}} and RuL{sub 3}{sup 4{minus}} by the particles greatly enhanced the rate of quenching such that only the reaction occurring on the surfaces of the particles was observed. Electron transfer from ABTS{sup 2{minus}} to RuL{sub 3}{sup 4-*} occurred by a static (nondiffusional) process, and the quenching efficiency was maximal ...

1989-02-23

454

Electrochemical properties of LiFePO{sub 4} prepared via ball-milling  

Energy Technology Data Exchange (ETDEWEB)

LiFePO{sub 4} cathode materials with distinct particle sizes were prepared by a planetary ball-milling method. The effects of particle size on the morphology, thermal stability and electrochemical performance of LiFePO{sub 4} cathode materials were investigated. The ball-milling method decreased particle size, thereby reducing the length of diffusion and improving the reversibility of the lithium ion intercalation/deintercalation. It is worth noting that the small particle sample prepared using malonic acid as a carbon source achieved a high capacity of 161 mAh g{sup -1} at a 0.1 C rate and had a very flat capacity curve during the early 50 cycles. However, the big particle samples ({proportional_to}400 nm) decayed more dramatically in capacity than the small particle size samples ({proportional_to}200 nm) at high current densities. The improvement in electrode ...

2009-04-01

455

Development of magnetic separation system of magnetoliposomes  

Energy Technology Data Exchange (ETDEWEB)

The magnetic separation technology using sub-microsized ferromagnetic particle is indispensable in many areas of medical biosciences. For example, ferromagnetic particles (200-500 nm) are widely used for cell sorting in stem cell research with the use of cell surface-specific antigens. Nanosized ferromagnetic particles (10-20 nm) have been suggested as more suitable in drug delivery studies given their efficiency of tissue penetration, however, the magnetic separation method for them has not been established. One of the major reasons is that magnetic force acting on the object particles decreases drastically as a particle diameter becomes small. In this study, magnetic force acting on the targets was enhanced by the combination of superconducting magnet and the filter consisting of ferromagnetic particle. By doing so, we confirmed that Fe{sub 3}O{sub 4} of 20 nm ...

2009-10-15

456

Control of airborne particle concentration and draught risk in an operating room  

Energy Technology Data Exchange (ETDEWEB)

The influence of location of airborne particle source, ventilation rate, air inlet size, supply air velocity, air outlet location, and heat source on the distributions of airborne particle concentration and draught risk in an operating room is investigated. The investigation is carried out by using a flow program with the k-[epsilon] model of turbulence. Based on a standard case, five cases, each with one changed parameter, are computed, and the detailed field distributions of air velocity, temperature, airborne particle concentration, and draught risk are presented. The parametric study concludes that, for a better air quality and thermal comfort, it is desirable to use a higher inflow rate, a larger inlet area, and a uniform velocity profile of supply air. Outlet location and heat source have little influence on the distributions of the particle concentration in the room. It has also been found that ...

1992-01-01

457

Adsorption of mercury vapor on particles  

Energy Technology Data Exchange (ETDEWEB)

The adsorption of mercury vapor on particles was studied by using soot particles generated by incineration of sewage sludge (EP-ash) and activated carbon particles. Through the experiments, it was found that, at 298 K, the EP-ash has a fairly high adsorption capacity for mercury vapor in the order of 10/sup -6/g/g, which is between that of the ordinary soils and that of activated carbon particles. Furthermore, it was found that physical adsorption of mercury vapor on the studied particles at high temperature is described by Dubinin's equation. On the basis of the equation, it was shown that EP-ash physically adsorbs very little mercury at high temperature, and therefore, most mercury in the EP-ash is chemically adsorbed or contained in a form of mercury compounds. Nevertheless, the total amount of mercury contained in the particles is very little ...

1986-07-01

458

A model of coal particle drying in fluidized bed combustion reactor  

Energy Technology Data Exchange (ETDEWEB)

Experimental and theoretical investigation on drying of a single coal particle in fluidized bed combustor is presented. Coal particle drying was considered via the moist shrinking core mechanism. The results of the drying test runs of low-rank Serbian coals were used for experimental verification of the model. The temperature of the coal particle center was measured, assuming that drying was completed when the temperature equalled 100{sup o}C. The influence of different parameters (thermal conductivity and specific heat capacity of coal, fluidized bed temperature, moisture content and superheating of steam) on drying time and temperature profile within the coal particle was analyzed by a parametric analysis. The experimentally obtained results confirmed that the moist shrinking core mechanism can be applied for the mathematical description of a coal particle drying, while dependence ...

2007-02-15

459

Year 2000 Computing Issues Related to the Defense Fuels ...  

Science.gov (United States)

... manual efforts by DESC and the Defense Finance and Accounting Service would ... in serious mission and financial impacts on DLA, DESC, the ...

1999-05-17

460

The Numerical Weather Prediction System at the Italian Air ...  

Science.gov (United States)

... Title : The Numerical Weather Prediction System at the Italian Air Force Weather Service: Impact of Non-Conventional Observations and Increased ...

2004-06-01

462

Telephone Flat Geothermal Development Project Environmental Impact Statement Environmental Impact Report. Final  

Energy Technology Data Exchange (ETDEWEB)

This Final Environmental Impact Statement and Environmental Impact Report (Final EIS/EIR) has been prepared to meet the requirements of the National Environmental Policy Act (NEPA) and the California Environmental Quality Act (CEQA). The Proposed Action includes the construction, operation, and decommissioning of a 48 megawatt (gross) geothermal power plant with ancillary facilities (10-12 production well pads and 3-5 injection well pads, production and injection pipelines), access roads, and a 230-kilovolt (kV) transmission line in the Modoc National Forest in Siskiyou County, California. Alternative locations for the power plant site within a reasonable distance of the middle of the wellfield were determined to be technically feasible. Three power plant site alternatives are evaluated in the Final EIS/EIR.

1999-02-01

463

Rim of the Pacific (RIMPAC). Programmatic Environmental ...  

Science.gov (United States)

... Air Station, Oahu, Kahuku Training Area ... K-Pier, Hawaii, Bradshaw Army Airfield, Hawaii (R&S ... impact area); Makua Military Reservation, Oahu (R&S ...

2002-06-01

464

Renewable energy systems - the environmental impact approach. Paper no. IGEC-1-008  

International Nuclear Information System (INIS)

High energy consumption and the world population increase will lead to a shrinking use of fossil fuels. The combustion of Fossil fuel leads to the increase of carbon dioxide concentration in the atmosphere which leads to the probable increase of global warming. Therefore, concerns about carbon dioxide emissions may discourage widespread dependence on fossil fuels and encourage the development and use of renewable energy systems employing a variety of technologies Renewable energy systems have themselves an environmental impact. Land use and material employed are two areas that may have an adverse impact to the positive environmental picture of the renewable energy systems. The objective of this paper is to analyze these impacts with the use of a very powerful tool, the Life Cycle Assessment. (author)

2005-06-12

465

Radiation processed composite materials of wood and elastic polyester resins  

International Nuclear Information System (INIS)

The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of ...

1982-09-19

467

Outpatient Prescribing Errors and the Impact of Computerized Prescribing  

UK PubMed Central (United Kingdom)

BackgroundMedication errors are common among inpatients and many are preventable with computerized prescribing. Relatively little is known about outpatient prescribing errors or...Full Text Available

2005-09-01

468

Occupational health impacts: offshore crane lifts in life cycle assessment  

British Library Electronic Table of Contents (United Kingdom)

Background, Aim, and Scope The identification and assessment of environmental tradeoffs is a strongpoint of life cycle assessment (LCA). A tradeoff made in many product systems is the exchange of potential for occupational accidents with the additional use of energy and materials. Net benefits of safety measures with respect to human health are best illustrated if the consequences avoided and health impacts induced by additional emissions are assessed using commensurable metrics. Our aim is to develop a human health impact indicator for offshore crane lifts. Crane lifts are a major cause of accidents on offshore oil and gas (O & G) rigs, and health impacts from crane lift accidents should be included in comparative LCA of O & G technologies if the alternatives differ in the use of crane li...

2008-01-01

469

New equipment recharges Oldham batteries  

Energy Technology Data Exchange (ETDEWEB)

The battery manufacturing industry has not been immune to the impact of new technologies. How one company is adapting production techniques to meet the demand for better products is discussed.

1982-09-24

470

Neuroimmunology of Stress: Skin Takes Center Stage  

UK PubMed Central (United Kingdom)

Like few other organs, the skin is continuously exposed to multiple exogenous and endogenous stressors. Superimposed on this is the impact of psychological stress on skin physiology and pathology....Full Text Available

2006-08-01

471

Neurocysticercosis, a Persisting Health Problem in Mexico  

UK PubMed Central (United Kingdom)

BackgroundThe ongoing epidemiological transition in Mexico minimizes the relative impact of neurocysticercosis (NC) on public health. However, hard data on the disease frequency...Full Text Available

472

Klickitat Cogeneration Project : Final Environmental Assessment.  

Energy Technology Data Exchange (ETDEWEB)

To meet BPA`s contractual obligation to supply electrical power to its customers, BPA proposes to acquire power generated by Klickitat Cogeneration Project. BPA has prepared an environmental assessment evaluating the proposed project. Based on the EA analysis, BPA`s proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969 for the following reasons: (1)it will not have a significant impact land use, upland vegetation, wetlands, water quality, geology, soils, public health and safety, visual quality, historical and cultural resources, recreation and socioeconomics, and (2) impacts to fisheries, wildlife resources, air quality, and noise will be temporary, minor, or sufficiently offset by mitigation. Therefore, the preparation of an environmental impact statement is not required and BPA is issuing this FONSI ...

1994-09-01

473

Intrinsic Motivation and Learning in a Schizophrenia Spectrum Sample  

UK PubMed Central (United Kingdom)

Amotivation is a telling hallmark of negative symptomatology in schizophrenia, and it impacts nearly every facet of behavior, including inclination to attempt the difficult cognitive tasks involved...Full Text Available

2010-05-01

474

Interfacial ultrafine-grained structures on aluminum alloy 6061 joint and copper alloy 110 joint fabricated by magnetic pulse welding  

British Library Electronic Table of Contents (United Kingdom)

Magnetic pulse welding is a solid state impact welding process, similar to explosive welding, which produces metallurgical bond by oblique high-speed impact between two metal bodies. This violent impact removes the metal surface oxide layers and then joins the two atomic level clean metal surfaces together by the incidental compression pressure. The impact velocity is at 200?400?m/s and the being welded metal surface undergoes severe plastic deformation with strain rate in the order of 106?107?s?1. The ultrafine-grained structure was observed on the welded interface. This article studied two types of similar material lap joint interfaces and the base metals were aluminum alloy 6061 and copper alloy 110. Nano-indentation testing shows that the welded interfaces have significantly greater ha...

2010-01-01

475

Impacts of Hugo Timber Damage on Primary Wood Manufacturers in ...  

Science.gov (United States)

Description: Hurricane Hugo, which struck South Carolina in September of 1989, destroyed a significant proportion of the State's timber. Primary wood-products ...

476

Impact on sexual function after reconstructive surgery for anterior urethral stricture disease  

UK PubMed Central (United Kingdom)

Objective:To evaluate the effect of urethral reconstructive surgery on sexual drive, erectile function and ejaculation.Materials and Methods:The...Full Text Available

2010-04-01

477

Impact on Benefits: Part-Time Schedule  

Science.gov (United States)

Jan 31, 2006 ... Sick leave accrues at the rate of 1 hour for each 20 hour in a pay status. ... FERS: All periods of service are used in determining the FERS ...

478

Impact of associated injuries in the Floating knee: A retrospective study  

UK PubMed Central (United Kingdom)

BackgroundFloating knee injuries are usually associated with other significant injuries. Do these injuries have implications on the management of the floating knee and the final...Full Text Available

479

Impact of a Statewide Internet-Based Tobacco Cessation Intervention  

UK PubMed Central (United Kingdom)

Background An increasing number of people have access to the Internet, and more people are seeking tobacco cessation resources online every year. Despite the...Full Text Available

480

Impact of Ionospheric Scintillations on Space-Based ...  

Science.gov (United States)

... Zinn, J., Hoerlin, H., and Petschek, AG, "The Motion of Bomb Debris Follow- ing the Starfish Test," Radiation Trapped in the Earth's Magnetic Field ...

1991-06-01

481

Human-modified ecosystems and future evolution  

UK PubMed Central (United Kingdom)

Our global impact is finally receiving the scientific attention it deserves. The outcome will largely determine the future course of evolution. Human-modified ecosystems are shaped by our activities...Full Text Available

2001-05-08

482

Flow characteristics, mechanical properties and chemical resistance of polycarbonate/polybutylene terephthalate/impact modifier blends  

Energy Technology Data Exchange (ETDEWEB)

Mechanical properties, flow characteristics and chemical resistance of polycarbonate (PC)/polybutylene terephthalate (PBT)/impact modifier (IM) blends were investigated over the various composition ranges of PC and PBT. Mechanical properties of the PC/PBT/IM blends for different IMs, butadiene based IM and butyl acrylate based IM, were studies for various compositions of the IMs. Impact strength at low temperature was also observed. For the study of chemical resistance of the PC/PBT/IM blends, the blends were dipped in organic solvent, thinner, and then variations of mechanical properties were analyzed. Tensile and flexural strengths were increased linearly and heat distortion temperature (HDT) also increased as PC content in the blends increased. Impact strength increased drastically as PC content increased up to 50 wt% and stayed stable value. Flowability decreased as PC content increased. impact ...

2002-03-01

483

Fiber Reinforced Superalloys - NASA Technical Reports Server  

Science.gov (United States)

hlgh fiber content composites met the minlmum requirements. (1400 O F ) , the hlgher fiber content as-fabricated composites have impact strengths distinctly ...

484

Evaluation of impacts on wetlands: do NEPA analyses integrate wetland protection requirements  

Energy Technology Data Exchange (ETDEWEB)

The impacts of federal projects on wetlands should be included in documents prepared to comply with the National Environmental Policy Act (NEPA). NEPA assessments of impacts on wetlands are often related to requirements of other laws, regulations, and executive orders, such as permitting requirements under Section 404 of the Clean Water Act and those contained in Executive Order 11990, Protection of Wetlands. This paper reviews recent NEPA environmental impact statements that contained assessments of impacts on wetlands or that involved projects likely to affect wetlands. It covers documents prepared by several federal agencies, including the Army Corps of Engineers, Department of Energy, Federal Highway Administration, Soil Conservation Service, and Tennessee Valley Authority. The extent and depth of analyses of wetlands issues was found to be highly variable, both within and among agencies. Most ...

1991-01-01

485

Environmental Impact Analysis Using Hybrid Decision Support Framework: A Transportation Project Case Study  

British Library Electronic Table of Contents (United Kingdom)

An Environmental Impact Assessment (EIA) study for any project is a time- consuming process because it has a large number of dependent and independent variables that must be taken into account. Although EIAs are dependent on geo-spatial information in order to make an assessment, there are no standard rules for conducting an environmental assessment. In addition, each assessment objective is case-dependent, based on what information is available. This paper presents a new framework for the analysis phase of the Environmental Impact Assessment (EIA) for projects, based on the integration between remote sensing technology, geographic information systems, and spatial modeling. The framework comprehensively analyzes the environmental vulnerability around the project areas and its impact on the...

2010-01-01

486

Environmental Impact Analysis Process. Final Environmental ...  

Science.gov (United States)

... Abstract : The United States Air Force (USAF) currently operates the Milstar satellite system to provide Military Satellite Communication Systems ...

2001-02-15

487

Environmental Assessment | Science & Technology | US EPA  

Science.gov (United States)

Report) A Screening Assessment of the Potential Impacts of Climate Change on Combined Sewer Overflow (CSO) Mitigation in the Great Lakes and New England Regions (Final Report)...

2011-09-30

488

Energy absorbers used against impact loading  

International Nuclear Information System (INIS)

In the WWER-440 reactor the primary piping consists of six horizontal loops going radially from the pressure vessel, each loop having a horizontal steam generator. In this reactor type the relatively long primary piping with many curved sections requires special attention in order to successfully eliminate the consequences of the design basis accident. Emergency supports are located in appropriate places to restrict the movements of the pipe. Under normal conditions there is a gap of some centimeters between the pipe and a support so that in the pipe can be deformed freely under changing loads. This paper deals with those energy-absorbing structures used at the Loviisa Nuclear Power Plant for protection against impact loading. Places and circumstances where energy-absorbing structures are employed are specified. Development and design of impact absorber elements are discussed and impact tests are described. (Auth.).

1975-09-08

489

Economic-impact analysis of effluent limitations and standards for the battery-manufacturing industry  

Energy Technology Data Exchange (ETDEWEB)

The report identifies and analyzes the economic impacts of water pollution control regulations on the battery manufacturing industry. These regulations include effluent limitations and standards based on BPT (best practical control technology currently available), BAT (best available technology economically achievable), PSES (pretreatment standards existing sources), NSPS (new source performance standards), and PSNS (pretreatment standards new sources), that have been promulgated under authority of Sections 301, 304, 306, 307, 308, and 501 of the Federal Water Pollution Control Act, as Amended (the Clean Water Act). The primary economic impact variables of interest include price changes, plant closures, substitution effects, changes in employment, shifts in the balance of foreign trade, changes in industry profitability, structure, and competition, and impacts on small business.

1984-01-01

490

EFFECT OF ANATOMIC MOTION ON PROTON THERAPY DOSE DISTRIBUTIONS IN PROSTATE CANCER TREATMENT  

UK PubMed Central (United Kingdom)

PurposeTo determine the dosimetric impact of inter-fraction anatomical movements in prostate cancer patients receiving proton therapy.Full Text Available

2007-02-01

491

Correlated Bivariate Continuous and Binary Outcomes: Issues and Applications  

UK PubMed Central (United Kingdom)

SUMMARYIncreasingly multiple outcomes are collected in order to characterize treatment effectiveness or to evaluate the impact of large policy initiatives. Often the multiple...Full Text Available

2009-06-15

493

Chronic Pain Associated with Upper-Limb Loss  

UK PubMed Central (United Kingdom)

ObjectiveTo describe the prevalence, intensity, and functional impact of the following types of pain associated with upper-limb loss: phantom limb, residual limb,...Full Text Available

2009-09-01

494

Cell proliferation and chemical carcinogenesis: symposium overview.  

UK PubMed Central (United Kingdom)

Cancer, by definition, is a proliferative disease. The fundamental scientific issue explored at the international symposium "Cell Proliferation and Chemical Carcinogenesis" was the impact of chemically...Full Text Available

1993-12-01

496

Assessment of information impacts in power system security against malicious attacks in a general framework  

International Nuclear Information System (INIS)

In the analysis of power systems security, recently a new concern related to possible malicious attacks caught much attention. Coordination among different transmission system operators (TSO) in an interconnected power system to counteract such attacks has become an important problem. This paper presents a general framework for describing the physical, cyber and decision-making aspects of the problem and their interrelations; within this framework, an analytic tool for the assessment of information impacts in handling on-line security after a malicious attack is proposed and discussed. The model is based on the socially rational multi-agent systems and the equilibrium of a fictitious play is considered to analyze the impacts of various levels of information available to the interconnected system operators on the outcomes of the decision-making process under attack. A 34-buses test system, with 3 systems interconnected by tie-lines, is presented ...

2009-06-01

498

Advisory Committee for GPRA Performance Assessment (AC/GPA) Report FY2003  

Science.gov (United States)

... impact. The Committee reviewed voluminous materials from NSF?s retrospective and prospective award ...

499

Adder bite: an uncommon cause of compartment syndrome in northern hemisphere  

UK PubMed Central (United Kingdom)

Snakebite envenomation is an uncommon condition in the northern hemisphere, but requires high vigilance with regard to both the systemic effects of the venom and the locoregional impact on the soft...Full Text Available