Energy Technology Data Exchange (ETDEWEB)

The intent and purpose of this work was to investigate and demonstrate cooperative behavior among a group of mobile robot machines. The specific goal of this work was to build a small swarm of identical machines and control them in such a way as to show a coordinated movement of the group in a flocking manner, similar to that observed in nature. Control of the swarm`s individual members and its overall configuration is available to the human user via a graphic man-machine interface running on a base station control computer. Any robot may be designated as the nominal leader through the interface tool, which then may be commanded to proceed to a particular geographic destination. The remainder of the flock follows the leader by maintaining their relative positions in formation, as specified by the human controller through the interface. The ...

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

The role of robotics and remote handling equipment in future nuclear power plant maintenance activities is discussed in the context of artificial intelligence applications. Special requirements manipulators, control systems, and man-machine interfaces for nuclear applications are noted. Tasks might include inspection with cameras, eddy current probes, and leak detectors; the collection of material samples; radiation monitoring; and the disassembly, repair and reassembly of a variety of system components. A robot with vision and force sensing and an intelligent control system that can access a knowledge base is schematically described. Recent advances in image interpretation systems are also discussed.

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under the session headings: research in mechanical fragmentation; rock characterization, remote sensing and interface detection; monitoring, data transmission and communications; tunnel boring machines; minewide monitoring and expert systems for ground control; machine guidance; shaft and raise boring; automation of drilling equipment; machine automation and control; new developments in mechanical miners; materials handling; innovative mining systems; general minewide monitoring and expert systems; ground support; human factors; and extraterrestrial mining.

Science.gov (United States)

A computer program entitled "Marshall Aerospace Vehicle Representation in C II,

Science.gov (United States)

... space vehicles, robot and machine guidance systems, and in various types of autonomous UUV docking situations. Page 3. ...

International Nuclear Information System (INIS)

A nuclear power plant engineering (NPP) simulator may include many system functions such as thermal-hydraulic calculation, 3D reactor neutron kinetics model, control and protection system, display and operational human-machine interface, intelligent alarm system, etc. If all those functions are simulated using a single code, the size of the program will cause structural or managerial problems, and the hardware requirement could be tremendous. Thus, any local function errors or changes may affect the whole code, which will make development and maintenance extremely costly. So the nondistributed code is not considered to be flexible and feasible. Currently, distributed and parallel technologies have been applied to develop NPPs engineering simulator for safety analysis, verification of advanced main control room display, operation and intelligent alarm design. The distributed simulation divides a huge task into several objects according to ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to investigate the applicability of a combined Global Positioning System and Inertial Measurement Unit (GPS/IMU) for information based displays on earthmoving machines and for automated earthmoving machines in the future. This technology has the potential of allowing an information-based product like Caterpillar's Computer Aided Earthmoving System (CAES) to operate in areas with satellite shading. Satellite shading is an issue in open pit mining because machines are routinely required to operate close to high walls, which reduces significantly the amount of the visible sky to the GPS antenna mounted on the machine. An inertial measurement unit is a product, which provides data for the calculation of position based on sensing accelerations and rotation rates of the ...

International Nuclear Information System (INIS)

Reactor Regulating System (RRS) of TAPP-3 and 4 (540 MWe PHWR) addresses issues of elaborate Flux Tilt Control as applied to large Reactor Cores in addition to the traditional Bulk Power (Actual Power) Control. The control of Bulk and Zonal Power by RRS through the use of Zonal Control Compartments (ZCCs) has been successfully demonstrated in the Indian PHWRs for the first time. Features like automation in Demand Power Maneuvering, Manual Movement of Reactivity Devices through the Human Machine Interface (HMI) and the supervised withdrawal of Shut-off Rods during Auto Criticality are also included. Special algorithms to measure and control the individual Zone Power and Bulk Power also form part of RRS algorithms. This paper describes the salient features of RRS of TAPP-3 and 4 and the improvement carried out based on the feedback of past 1 year of operation of TAPP-4 at around 90 % FP. (author)

Science.gov (United States)

... non- emissive guidance and collision alert, automated transport in dynamic environments, and assembly and inspection. Foveal Vision, Autonomous Agents, ...

Energy Technology Data Exchange (ETDEWEB)

According to the development of power electronic element (GTO, IGBT) nd material for electrical machines (permanent magnet, super conductor), the technology for electrical machines is now a day rapidly developing. here with, a novel electrical machine, based on the new conception of transverse flux configuration leads to a considerable increase in power density and enables simultaneously high efficiency.The transverse flux machine with PM excitation will be applied to gearless direct drives for railway traction system. The designed and measured performance of transverse machine for railway traction system revealed a great potential of system improvements to reduce linear motor mass. (author). 10 refs., 14 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under the following topics: machine control and automation; rock drilling; cutting and fragmentation; rock characterization, remote sensing and interface detection; artificial intelligence and mine monitoring systems; computer applications; mechanical excavators; material handling; surface and underground mining; innovative mining systems; new developments in mechanical miners; ground hazard detection and control; ground support; and extraterrestrial mining.

British Library Electronic Table of Contents (United Kingdom)

Electrochemical discharge machining (ECDM) is a promising hybrid process for high-performance machining of non-conductive glass. ECDM drilling has been found to have different characteristics and material removal mechanisms in discharge regime (less than 300??m in depth) and hydrodynamic regime (more than 300??m in depth); however, these regimes are never separately modeled in existing ECDM models, which leads to large prediction error, especially at low applied voltages and high machining depths. Until now, no model is particularly designed for discharge regime, where most material is removed. In this paper, a finite element based model for ECDM drilling in discharge regime is presented. Material removal subjected to a single spark was simulated using finite element method. The drilling d...

CERN Document Server

In the context of the LHC Computing Grid (LCG) project, the Applications Area develops and maintains that part of the physics applications software and associated infrastructure that is shared among the LHC experiments. The "Physicist Interface" (PI) project of the LCG Application Area encompasses the interfaces and tools by which physicists will directly use the software, providing implementations based on agreed standards like the AIDA interfaces for data analysis. In collaboration with users from the experiments, work has started with implementing the AIDA interfaces for (binned and unbinned) histogramming, fitting and minimization as well as manipulation of tuples. These implementations have been developed by re-using existing packages either directly or by using a (thin) layer of wrappers. In addition, bindings of these interfaces to the Python interpreted ...

Energy Technology Data Exchange (ETDEWEB)

The difficulty in making good Ohmic contact at the interfaces with p-doped ZnSe is an important problem hindering the realization of blue-light-emitting diode lasers based on the II-VI semiconductor technology. So far no metal or semiconductor material has been found to have a low enough barrier at the (001) interface with ZnSe. A possible solution to this problem is the insertion of a so-called {ital barrier-reduction layer} at the interface with ZnSe. We have investigated the interface formation energies and valence-band offsets at the (001) interface between Al{sub x}Ga{sub 0.5{minus}x}In{sub 0.5}P and ZnSe. The results of our calculations show the existence of a strong interdependence between the valence-band offset and the interface geometric structure. The interface is found to have structural and electronic ...

Energy Technology Data Exchange (ETDEWEB)

A decoupled characteristic between the damping of a specific swing mode and the stabilizer gain of the corresponding machine in multimachine power systems is identified. Using this decoupled characteristic a power system stabilizer (PSS) synthesis approach which is based on the phase compensation concept is verified on a 9-machine system and the dynamic performance of this system is significantly improved. This method is proved to be effective, simple and it can provide useful guidance for the PSS field tuning.

International Nuclear Information System (INIS)

An outline of the instrumentation and control systems associated with fuelling machines is given. The control systems such as hydraulic system, oil hydraulic system, electric control system and the remote control systems have been discussed in detail. The difference between RAPP and MAPP fuel handling control systems has been explained. A computer based system for the Narora fuel handling control system is also discussed. (S.K.K.).

Energy Technology Data Exchange (ETDEWEB)

In this paper, power system stabilizer design for multi-machine power systems is translated into an equivalent problem of decentralized controller design for Multi-Output Multi-Input (MIMO) control systems. Subject to a condition based on the structured singular values, each stabilizer can be designed independently. Within this general framework, the conventional stabilizer design methodology based on the concept of synchronous and damping torques is used to decide the design details of each stabilizer. The suggested design method is applied to a model of a practical 10 machine power system. (author)

Energy Technology Data Exchange (ETDEWEB)

The coking plant is described with some details of coal supplies and coke quality. Engineering improvements to the by-product system and coke oven machines, major repair of two batteries, installation of a PLC-based monitoring and control system, and training of personnel are dealt with at greater length.

Science.gov (United States)

One of the tasks comprising ERDA Contract EY-76-S-02-2840, ''Minimization of Cupola Energy and Air Pollution,'' has been the carrying out of a comprehensive survey of world literature relating to the cupola furnace for melting of cast iron. It was decided...

Energy Technology Data Exchange (ETDEWEB)

The applications of neutron reflectometry to study dynamic phenomena at surface and interfaces have been restricted so far. This was mainly due to the low intensity of neutron sources, but now high-intensity spallation neutron sources are under construction in Japan (J-PARC) and US (SNS). We are planning to install a spin-echo option on the J-PARC neutron reflectometer with horizontal sample geometry for studies of dynamics of surfaces and interfaces. This option is based on the resonance spin-echo method and aimed at dynamics up to hundreds of nanoseconds. In this contribution, the plan and status of development are introduced together with the principle and characteristics of this option.

International Nuclear Information System (INIS)

The basic relationships of the convolution/superposition dose calculation technique are reviewed, and a modelling technique that can be used for obtaining a satisfactory beam model for a commercially available convolution/superposition-based treatment planning system is described. A fluence energy spectrum for a Co-60 treatment machine obtained from a Monte Carlo simulation was used for modelling the fluence spectrum for a Rokus M machine. In order to achieve this model we measured the depth dose distribution and the dose profiles with a Wellhofer dosimetry system. The primary fluence was iteratively modelled by comparing the computed depth dose curves and beam profiles with the depth dose curves and crossbeam profiles measured in a water phantom. The objective of beam modelling is to build a model of the primary fluence that the patient is exposed to, which can then be used for the calculation of the dose deposited in the ...

British Library Electronic Table of Contents (United Kingdom)

Retaining an appropriate level of moisture at the interface between a healing wound and an applied dressing is considered to be critical for effective wound healing. Failure to control exudate at this interface can result in maceration or drying out of the wound surface. The ability to control moisture balance at the wound interface is therefore a key aspect of wound dressing performance. To date it has not been possible to monitor in any effective manner the distribution of moisture within dressings or how this varies with time.A new measurement system is presented based on sensors placed at the wound/dressing interface which are capable of monitoring moisture levels in real time. The system comprises a model wound bed and sensor array complete with fluid injection path to mimic exudate f...

UK PubMed Central (United Kingdom)

BackgroundThe successful use of zirconia ceramics in orthopedic surgery led to a demand for dental zirconium-based implant systems. Because of its excellent biomechanical characteristics,...Full Text Available

UK PubMed Central (United Kingdom)

Recent health care policies and regulations have impacted the manner in which patient data – especially protected health information (PHI) – are handled in both the clinical...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The subject of FDD (fault detection and diagnosis) has gained widespread industrial interest in machine condition monitoring applications. This is mainly due to the potential advantage to be achieved from reduced maintenance costs, improved productivity and increased machine availability. This paper presents a new FDD scheme for condition machinery of an industrial steam turbine using a data fusion methodology. Fusion of a SVM (support vector machine) classifier with an ANFIS (adaptive neuro-fuzzy inference system) classifier, integrated into a common framework, is utilized to enhance the fault detection and diagnostic tasks. For this purpose, a multi-attribute data is fused into aggregated values of a single attribute by OWA (ordered weighted averaging) operators. The simulation studies indicate that the resulting fusion-based scheme outperforms the individual SVM and ANFIS systems to detect and ...

British Library Electronic Table of Contents (United Kingdom)

Thermal desorption spectroscopy (TDS) was used to study outgassing from polycrystalline SiGe (poly-SiGe), SiC and SiO"2 films used for poly-SiGe-based MEMS thin film vacuum package technology. Primary desorption products were found to be H"2, H"2O and CO"2. The CO"2 outgassing could be correlated with CF"4 plasma interface cleaning used for thick SiGe PECVD, which can leave carbon at the CF"4-plasma-cleaned interface.

Energy Technology Data Exchange (ETDEWEB)

This paper describes a dissipativity-based framework for the study of low-frequency oscillations in power systems and for power system stabilizer design. This framework leads to a robust controller design formulation, amenable to both H{sub {infinity}} and QFT tools. An illustrating numerical example presents QFT based design for a widely used benchmark two area, four machine power system.

International Nuclear Information System (INIS)

In order to prevent corrosion failures of machines and structures, it is desirable to know in advance when the corrosion damage will take place, and appropriate measures are needed to mitigate the damage. The corrosion predictions are needed both at development as well as operational stage of machines and structures. There are several forms of corrosion process through which varying degrees of damage can occur. Under certain conditions these corrosion processes at alone and in other set of conditions, several of these processes may occur simultaneously. For a certain type of machine elements and structures, such as gears, bearing, tubes, pipelines, containers, storage tanks etc., are particularly prone to pitting corrosion which is an insidious form of corrosion. The corrosion predictions are usually based on experimental results obtained from test coupons and/or field experiences of similar ...

International Nuclear Information System (INIS)

An artificial neural network can be used as an intelligent controller to control non-linear, dynamic system through learning. It can easily accommodate non-linearities and time dependencies. Most common multi-layer feed-forward neural networks have drawbacks of large number of neurons and hidden layers required to deal with complex problems and require large training time. To overcome these drawbacks, a generalized neuron based non-linear controller has been developed and illustrated as a power system stabilizer. Studies on a five-machine power system show that the proposed controller can significantly improve the dynamic performance and provide good damping of the power system over a wide operating range.

Energy Technology Data Exchange (ETDEWEB)

A simple model based on surface chemistry is developed, based an simple concepts of contact angle, wetting and spreading. Results of the modeling can be stated by two simplified ``rules of thumb``: (1) A liquid will spread on the surface of a solid if the surface tension of the liquid is lose than the surface free energy of the solid, and (2) The liquid having the surface tension nearest that of the solid will preferentially wet the surface of the solid. These two rules can then be used to define the parameters that constitute a process for formulating a plastic bonded explosive (PBX), which is a crystalline high-explosive material coated with a small amount of plastic polymeric material (the binder). The PBX then can be pressed to a high density, and machined to a specific shape. The pressed and machined explosive material can then be used in a physics experiment to study fundamental properties of ...

CERN Document Server

Multimodal interfaces are becoming increasingly ubiquitous with the advent of mobile devices, accessibility considerations, and novel software technologies that combine diverse interaction media. In addition to improving access and delivery capabilities, such interfaces enable flexible and personalized dialogs with websites, much like a conversation between humans. In this paper, we present a software framework for multimodal web interaction management that supports mixed-initiative dialogs between users and websites. A mixed-initiative dialog is one where the user and the website take turns changing the flow of interaction. The framework supports the functional specification and realization of such dialogs using staging transformations -- a theory for representing and reasoning about dialogs based on partial input. It supports multiple interaction interfaces, and offers sessioning, caching, and ...

British Library Electronic Table of Contents (United Kingdom)

Magnetic pulse welding is a solid state impact welding process, similar to explosive welding, which produces metallurgical bond by oblique high-speed impact between two metal bodies. This violent impact removes the metal surface oxide layers and then joins the two atomic level clean metal surfaces together by the incidental compression pressure. The impact velocity is at 200?400?m/s and the being welded metal surface undergoes severe plastic deformation with strain rate in the order of 106?107?s?1. The ultrafine-grained structure was observed on the welded interface. This article studied two types of similar material lap joint interfaces and the base metals were aluminum alloy 6061 and copper alloy 110. Nano-indentation testing shows that the welded interfaces have significantly greater ha...

Energy Technology Data Exchange (ETDEWEB)

The pH of the solution is shown to significantly effect the reflection anisotropy spectroscopy (RAS) profiles of adenine adsorbed at Au(110)/electrolyte interfaces. At pH 12.8 the net adsorption is very weak due the formation of negative adenine ions in solution. The sensitivity of the RAS profiles to the pH of the solution is probably due to a change in the geometry of the adsorbed molecules caused by a disruption of the base stacking configuration that is adopted when adenine is adsorbed from solutions at pH 7.1. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Successful interface engineering requires compositional and electronic material characterization as a prerequisite for understanding and intentionally generating interfaces in photovoltaic devices. The paper gives an overview with several examples, all referring to Cu(In,Ga)(S,Se){sub 2} ('CIGSSe')-based solar cells, with an emphasis on characterization using highly specialized methods, such as elastic recoil detection analysis, X-ray emission spectroscopy and photoelectron spectroscopy using synchrotron and ultraviolet light for excitation, inverse photoemission spectroscopy and Kelvin probe force microscopy. First, the determination of the depth profile of the band gap energy E{sub g} in the absorber layer is demonstrated. The modification of E{sub g} towards both interfaces is discussed in terms of beneficial electronic effects. Next, the interface between ...

CERN Document Server

Recently, applying the novel data mining techniques for evaluating enterprise financial distress has received much research alternation. Support Vector Machine (SVM) and back propagation neural (BPN) network has been applied successfully in many areas with excellent generalization results, such as rule extraction, classification and evaluation. In this paper, a model based on SVM with Gaussian RBF kernel is proposed here for enterprise financial distress evaluation. BPN network is considered one of the simplest and are most general methods used for supervised training of multilayered neural network. The comparative results show that through the difference between the performance measures is marginal; SVM gives higher precision and lower error rates.

Energy Technology Data Exchange (ETDEWEB)

A novel adaptive stabilizer, called an Adaptive Governor Power System Stabilizer (AGPSS), which operated on the governor turbine system, was described. There has been extensive research on adaptive excitation control of generators in power systems with the goal of achieving better dynamic performance. AGPSS tracks the frequency and damping of oscillations in a power system, and adjusts to ensure that there is always sufficient damping in the system. There is no interaction between stabilizers on different generating units, and each one acts independently, consuming oscillation energy locally. These stabilizers are easy to design and this facilitates their use in multimachine systems. Results obtained by nonlinear simulation of a single-machine and a three-machine power system were discussed, illustrating the effectiveness of the stabilizers in supplying damping and improving stability. It was pointed out that the operation of AGPSS does not ...

International Nuclear Information System (INIS)

The paper develops a new design procedure for simultaneous coordinated designing of the thyristor controlled series capacitor (TCSC) damping controller and power system stabilizer (PSS) in multi-machine power system. The coordinated design problem of PSS and TCSC damping controllers over a wide range of loading conditions is converted to an optimization problem with the time domain-based objective function that is solved by a particle swarm optimization (PSO) technique which has a strong ability to find the most optimistic results. By minimizing the proposed fitness function in which oscillatory characteristics between areas are included and thus the interactions among the TCSC controller and PSS under transient conditions in the multi-machine power system are improved. To ensure the robustness of the proposed stabilizers, the design process takes a wide range of operating conditions into account. The effectiveness of the ...

International Nuclear Information System (INIS)

The Gigabit Link Interface Board (GLIB) is an evaluation platform and an easy entry point for users of high speed optical links in high energy physics experiments. Its intended use ranges from optical link evaluation in the laboratory to control, triggering and data acquisition from remote modules in beam or irradiation tests. The GLIB is an FPGA-based Advanced Mezzanine Card (AMC) conceived to serve a small and simple system residing either inside a Micro Telecommunications Computing Architecture (?TCA) crate, or on a bench with a link to a PC. This paper presents the architecture of the GLIB, its features as well as examples of its use in different setups.

Energy Technology Data Exchange (ETDEWEB)

It is very important to develop the design guidelines which can be applicable for Korean operators for the purpose of designing the KSNP more safely. The objective of this project is to provide the standards, guidelines and bases applicable for HF-010 through the within-subject experiment for obtaining Korean operators' population stereotype for direction-of-movement of controls associated with displays on the control panels. Through the survey of researches on display compatibility and the classification of types of displays and controls in the main control room of Uljin units 3 and 4, methods for an experiment on the stereotype were established. Experimental interface prototypes for a total of 108 combinations of display and control types were implemented. Experimental data collection and analysis system was built in association with the interface prototypes. The experiment was performed with participation of 250 ...

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force ...

CERN Document Server

Ubiquitous computing based on small mobile devices using wireless communication links is becoming very attractive. The computational power and storage capacities provided allow the execution of sophisticated applications. Due to the fact that sharing of information is a central problem for distributed applications, the development of self organizing middleware services providing high level interfaces for information managing is essential. ADS is a directory service for mobile ad-hoc networks dealing with local and nearby information as well as providing access to distant information. The approach discussed throughout this paper is based upon the concept of information markets.

Energy Technology Data Exchange (ETDEWEB)

The objectives of this R and D project are as follows : First, transferring developed technologies to outside companies and operating technology market to vitalize technology transactions, Second, developing commercial application projects to transfer technologies for commercial purposes and to solve interface problems in commercial applications, Third, enhancing commercial utilizations of developed accelerator and beam utilization technologies, Finally. preparing infra-structures for the development of over 30 venture- businesses based on achieved technologies through the Proton Engineering Frontier Project.

Energy Technology Data Exchange (ETDEWEB)

The distribution of graphite particles in graphite containing copper alloy was further improved very significantly using several procedures and technological modifications. The developed techniques attacked the graphite distribution problem in two ways. Realizing that clustering of very fine (5um) graphite particles is one of the two major problems, a pretreatment process has been developed using aluminum powders to deagglomerate graphite particles. Along with this, a two-stage stirring technique was used to first incorporate and then to distribute uniformly the deagglomerated particles in the melt. During this year, based on these developments, several components were cast to evaluate the castability of Cu alloy-graphite melts. In addition, machinability tests were done to clearly established that addition of graphite particles improve the machinability of copper MMC alloys over and above that of monolithic copper alloys. ...

International Nuclear Information System (INIS)

Aiming at the non-stationary characteristics of differential pressure fluctuation signals of gas-liquid two-phase flow, and the slow convergence of learning and liability of dropping into local minima for BP neural networks, flow regime identification method based on Singular Value Decomposition (SVD) and Least Square Support Vector Machine (LS-SVM) is presented. First of all, the Empirical Mode Decomposition (EMD) method is used to decompose the differential pressure fluctuation signals of gas-liquid two-phase flow into a number of stationary Intrinsic Mode Functions (IMFs) components from which the initial feature vector matrix is formed. By applying the singular vale decomposition technique to the initial feature vector matrixes, the singular values are obtained. Finally, the singular values serve as the flow regime characteristic vector to be LS-SVM classifier and flow regimes are identified by the output of the classifier. The ...

Energy Technology Data Exchange (ETDEWEB)

Momentum transfer through an air-water interface was studied in a horizontal rectangular channel through experimental and numerical analysis. The liquid flow Reynolds numbers, based on hydraulic diameters, were 11500 and 17000. The air flow Reynolds number varied from 0 to 3260. In experiments, velocity distribution was measured by hot-film and hot-wire probes. The effect of the liquid flow Reynolds number and the direction of interfacial shear stress was investigated by performing the cocurrent and countercurrent experiments. The modified k-{epsilon} model was able to reproduce these experimental results qualitatively. The range of applicability of the modified k-{epsilon} model was also discussed. (author).

British Library Electronic Table of Contents (United Kingdom)

A protocol adapter ideally suited to enable enterprises to gradually transition from SOAP Web Services to RESTful HTTP Web Services without impacting existing clients is presented in this paper. The inherent advantage of such a transition is the visibility of RESTful HTTP messages to Web intermediaries such as caches. In contrast, SOAP messages are opaque, which disables Web intermediaries. While both approaches can use HyperText Transfer Protocol (HTTP) for message transfer, the paradigms contrast sharply. SOAP uses an interface specific approach whereas RESTful HTTP uses a Uniform Interface approach. SOAP marks up its payload with eXtensible Markup Language (XML) whereas in certain situations RESTful HTTP requires no XML. We present the disadvantages of the SOAP approach and outline how ...

Energy Technology Data Exchange (ETDEWEB)

Four interrelated projects are underway whose purpose is to migrate the LAMPF-PSR Accelerator Complex control systems to a system with a common set of hardware and software components. Project goals address problems in performance, maintenance and growth potential. Front-end hardware, operator interface hardware and software, computer systems, network systems and data system software are being simultaneously upgraded as part of these efforts. The efforts are being coordinated to provide for a smooth and timely migration to a client-sever model-based data acquisition and control system. An increased use of the distributed intelligence at both the front-end and operator interface is a key element of the projects. 2 refs., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

The Reactor Head Structure Assembly(RHSA) is the structure located on the reactor assembly. The purpose of the assembly is providing interface location for cables, preventing pipe whips, prohibiting instruments from becoming missiles, and restraining CEDMs' horizontal motion. On the RHSA, Reactor Disconnect Panels(RDP) are installed. The installation location of RDP is to be decided to minimize the geometric interface with other components. Since the neighborhood of RHSA is crowded due to many connectors and cables, it is necessary to find the good design of RHSA to make an intricate situation attenuated and the required function maintained. The geometric shape and overall configuration of RHSA are determined by axiomatic design approach. The FRs of RHSA are specified and the corresponding DPs are found to satisfy FRs in sequence. The finite element analysis is carried out based on the result of the axiomatic ...

British Library Electronic Table of Contents (United Kingdom)

Problems of classification and regression estimation in which objects are represented by multidimensional arrays of features are considered. Many practical statements can be reduced to such problems, for example, the popular approach to the description of images as a set of patches and a set of descriptors in each patch or the description of an object in the form of a set of distances from it to certain support objects selected based on a set of features. For solving problems concerning the objects thus described, a generalization of the relevance vector model is proposed. In this generalization, specific regularization coefficients are defined for each dimension of the multidimensional array of the object description; the resultant regularization coefficient for a given element in the mul...

International Nuclear Information System (INIS)

At the importance increase of UT (ultrasonic testing) with the application of rules on fitness-for-service for nuclear power plants, JAPEIC (Japan power engineering and inspection corporation) started education training for defect detection and sizing technique. Weld joints specimen with EDM (Electro-Discharged Machining) notches, fatigue cracks and intergranular stress corrosion cracks were tested and practiced repeatedly based on a modified ultrasonic method and the defect size measuring accuracy of the trainees was surely improved. Results of the blind test confirmed effectiveness of education training. (T. Tanaka)

Energy Technology Data Exchange (ETDEWEB)

A model-based technique incorporating neural networks has been developed for process monitoring. The technique is intended for processes where the uncertainty in the reference model is larger than desired but where process measurements providing additional information about the behavior of the system are available. This data is used to reduce the uncertainty of the model. The technique has been implemented in a real-time system for monitoring operational changes of mechanical equipment for use in predictive maintenance applications. Tests on a peristaltic pump were conducted and demonstrate the advantages of the proposed technique.

Energy Technology Data Exchange (ETDEWEB)

Artificial Neural Networks (ANNs) are parallel distributed processing machines. The unique characteristics of ANNs are: Fault tolerance, robustness, plasticity and generalization. These offer great potential in many AI applications such as character recognition. Handwritten character recognition is an intrinsically interesting problem, but the difficulties of this task are the many variations in the characters. A robust new incremental learning method, which combines supervised and unsupervised learning paradigms implemented by the Functional Link Net, is illustrated with experimental results. Clustering, based on unsupervised learning, classifies the input data into several categories. The supervised learning paradigm then further classifies the data in the clustered categories.

Energy Technology Data Exchange (ETDEWEB)

One of the most complicated tasks during the assembly of the Wendelstein W7-X is the installation of the superconductive coil system. The entire magnet system is enclosed between the Outer Vessel and the plasma vessel in high vacuum at 4 K. The coils are supported by a support structure, the Central Support Structure (CSS). The CSS carries all 70 coils, and it is designed as a closed ring made of 5 modules (10 half modules). The whole structure is supported by 10 Cryolegs which rest on the machine base. This paper describes the final design and manufacture of these Cryolegs.

Energy Technology Data Exchange (ETDEWEB)

A new recurrent neural network power system stabilizer (RNNPSS) based on genetic algorithm (GA) was presented. It shows faster convergence than the linear quadratic regulator (LQR) stabilizer in a multi-machine power system, because the proposed GA based neural network was first trained off-line to determine the optimal values of the learning rates. Otherwise, the RNNPSS consists of just two layers. As such, the time consumption of the damping oscillations is lower than with conventional methods. In addition, the operating range of the RNNPSS is greater than that of the LQR and conventional three layer neural networks, since the RNNPSS can greatly reduce system complexity and effectively damp system oscillations. 9 refs., 7 figs.

International Nuclear Information System (INIS)

In this paper, a neural networks (NN) based adaptive sliding mode controller (SMC) is introduced. The selection of SMC feedback gains is normally based on one operating point and thus the performance of the controller away from the design operating point is, of necessity, a compromise. The adaptive SMC is proposed to overcome the limitations imposed on the effectiveness of the SMC under different operating conditions. Neural networks are used for online prediction of the optimal SMC gains when the operating point changes. The proposed method has been applied to a power system stabilizer (PSS) of a single machine power system. Simulation results are included to demonstrate the performance of the proposed control scheme.

Energy Technology Data Exchange (ETDEWEB)

The oceanic phytoplancton productivity may essentially influence the total rate of the atmospheric CO{sub 2} absorption by the ocean - that is, a considerable amount of CO{sub 2} will be taken-up in the 50 micrometers thick layer near the air-sea interface. Even if phytoplancton production constitutes only 5% of the total oceanic biota production, this will increase the rate of CO{sub 2} absorption more than twice compared with the present estimates. The reason is that metabolic activity of phytoplancton leads to the emergence in a thin scin (50 micrometers, the average size of phytoplancton cells) layer near the water surface of an additional minimum in the CO{sub 2} partial pressure profile and of an additional maximum of {Delta} {sup 13}C in the same area. These two extremums cannot be detected if the corresponding characteristics are averaged over any microscopic area in the well mixing layer that is more than 1 meter deep, which is usually the case when the ...

Science.gov (United States)

The study is concerned with the Stefan problem of evaporation of a volatile component from its solution with a virtually non-volatile material. The analysis provides an analytical solution to the problem based on mass-transfer fundamentals. Results yield the evaporation rate, interfacial mole fractions, concentration profiles in the gas and liquid phases, and the location of the evaporation front. The analysis can be used to provide the binary liquid diffusion coefficient of the volatile component based on experimental data for the liquid gas interface position as a function of time. The requirements for such a measurement are discussed in terms of the volatility of the evaporating component and its initial concentration in the liquid mixture.[Figure not available: see fulltext.

International Nuclear Information System (INIS)

High temperature fatigue crack growth (FCG) and creep crack growth (CCG) experiments have been conducted in air on weld metal, heat affected zone (HAZ) and base metal of the austenitic Alloy 800 and the nickel base Alloy 617. Tests were performed on specimens machined from pipes, in the temperature range 550-900 deg. C. The crack propagation mode was examined. At all temperatures and for both materials, FCG of base metal was found to be the highest, whereas the weld metal exhibited the lowest FCG rate. The FCG rate in the HAZ was found to lie in between of those observed for base and weld metal. The crack propagation mode remained transgranular in base metal and transdendritic in weld metal at all temperatures. CCG behaviour could be described using the energy rate integral C*. Base metal and weld metal exhibited similar CCG rate at same C*. ...

International Nuclear Information System (INIS)

Short communication.

International Nuclear Information System (INIS)

... 194 p. auger electron spectroscopy decomposition deposition interfaces oxygen

Energy Technology Data Exchange (ETDEWEB)

The effect of various window layers for InP solar cells are studied. Window materials that have type 1 and type 2 alignment in the window/emitter interface are compared. All window materials that form a type 2 alignment with InP, such as Al{sub 0.20}In{sub 0.80}P, Ga{sub 0.20}In{sub 0.80}P, Al{sub 0.55}In{sub 0.45}As and Al{sub 0.60}In{sub 0.40}P, cause a high interface recombination velocity, which deteriorates the carrier collection. This recombination takes place due to the spatially indirect quantum well transition between the triangular quantum wells formed in the interface. ZnSe as a window layer material with type 1 alignment does not have this problem, but still decreased response in the short wavelength region is observed due to misfit dislocation induced trap sites. Future prospects for the window layer development for InP are discussed. The discussion is extended also to other III-V semiconductor ...

Energy Technology Data Exchange (ETDEWEB)

This thesis develops methods for recording and analysis of seismo-acoustic interface waves for determination of shear wave velocity as a function of depth and includes this in standard refraction seismic surveying. It investigates different techniques for estimation of dispersion characteristics of the interface waves and demonstrates that multi sensor spectral estimation techniques improve the dispersion estimates. The dispersion estimate of the fundamental interface wave mode is used as input to an object function for a model based linearized inversion. The inversion scheme provides an estimate of the shear wave velocity as a function of depth. Three field surveys were performed. Data were acquired with a standard bottom deployed refraction seismic hydrophone array containing 24 or 48 receivers, with a receiver spacing of 2.5 m. Explosive charges were used as sources. The recording time was increased ...

International Nuclear Information System (INIS)

Particulate (i.e. tokamak dust) has been collected from the DIII-D tokamak located at General Atomics in San Diego, CA, USA. Two methods were used to collect particulate with the goal of preserving the particle size distribution and physical characteristics of the particulate. Vacuum collection on substrates and adhesion removal with metallurgical replicating tape were chosen as non-intrusive sampling methods. Sampling was completed in four toroidal locations of the machine; the 0-90 area, the 90-180 area, the 180-270 area, and the 270-360 area. The 0 direction designates the north side of the DIII-D machine. Four tiles in each area were sampled; the first vertical tile above the floor on the centerpost, a floor tile next to the center post, a tile on the isolated ring, and the first tile up from the isolated ring on the divertor. In addition, samples were collected from underneath the floor tiles at the 275 and the 75 locations. The count ...

International Nuclear Information System (INIS)

... brakes reactor charging machines reactors machine parts Int. Cl. B66d5/00;

Energy Technology Data Exchange (ETDEWEB)

The ACP Multi-Array Processor System (ACPMAPS) is a highly cost effective, local memory parallel computer designed for floating point intensive grid based problems. The processing nodes of the system are single board array processors based on the FORTRAN and C programmable Weitek XL chip set. The nodes are connected by a network of very high bandwidth 16 port crossbar switches. The architecture is designed to achieve the highest possible cost effectiveness while maintaining a high level of programmability. The primary application of the machine at Fermilab will be lattice gauge theory. The hardware is supported by a transparent site oriented software system called CANOPY which shields theorist users from the underlying node structure. 4 refs., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

This paper is devoted to the coordination of secondary voltage control and adaptive parameters resetting of the power system stabilizer, in order to increase stability, margins in real time operation. Secondary voltage control and the power system stabilizer are two control loops, which affect the same system parameter on different bases - that parameter is the voltage set-point of the automatic voltage regulator. It was found that their effects were complementary. In that way, through the proper coordination of actions of these two control loops open up a wide range of possibilities for ensuring the stability of bulk power systems in real time. For the establishment of this coordination, an on-line sequential algorithm is proposed which is based on adaptive resetting of the voltage set-point of the automatic voltage regulator and the PSS parameters. The efficiency of the proposed algorithm is confined through simulations on a real-life ...

International Nuclear Information System (INIS)

Background vibration in a CANDU plant can be used to determine the dynamic characteristics of major items of equipment, such as calandria, the fuelling machines and the primary heat transport pumps. These dynamic characteristics can then be used to verify the seismic response of the equipment which, at present, is based on theoretical models only. The feasibility and basic theory of this new approach (which uses accelerations measured at several points on a structure and does not require knowledge of the source of excitation) was established in Phase I of the study. This report is based on Phase II in which the methods of analysis developed in Phase I were improved and verified experimentally. A Fast Fourier Transform (FFT) algorithm was incorporated and an interactive curve fitting technique was developed to obtain the dynamic characteristics in the form of natural frequencies, mode shapes and damping ratios. The method is ...

Science.gov (United States)

Phenomena in power systems tend to exhibit higher nonlinearity, because efficient operation accompanies severer power transfer. In such cases, there might exist some limitation to the use of conventional linear control design scheme due to the nonlinearity. As for consideration to the nonlinearity, we have developed a nonlinear analysis method based on normal form theory. In this paper, we develop a new control design scheme based on the nonlinear analysis method. The developed method is effective in a case when oscillatory instability occurs. In the developed method, the parameters of control devices are adjusted so as to enlarge the stability limit against the oscillatory instability, unless each eigenvalue exceed its allowable threshold. We verify the effectiveness of the developed method in the IEEJ 10-machine System Model by applying to PSS (Power System Stabilizer). We show that the power transfer limit increases by ...

Energy Technology Data Exchange (ETDEWEB)

A power system stabilizer based on GMV (Generalized Minimum Variance), one of the adaptive control techniques, is developed to enhance the dynamic performances of a power system using an Artificial Neural Network (ANN). The stabilizer consists of two parts. One part is Inverse Dynamics Neural Networks (IDNN), which is trained to identify the inverse dynamics of controlled plant and used as a one-step ahead controller, or inverse controller. The other part is Adaptive Reference Model (ARM), which prevents excessive controller output. The ARM produces the modified reference value by minimizing a cost function recursively on the assumption that the IDNN perfectly identifies the controlled plant. The IDNN is used in the minimization procedure to calculate the sensitivities. The proposed controller is simulated in a typical one-machine-infinite-bus power system to show its effectiveness to damp sustained low frequency oscillation. (author)

Energy Technology Data Exchange (ETDEWEB)

We report on the software aspects of the development of a switch-based data acquisition system at Fermilab. This paper describes how, with the goal of providing an ``integrated systems engineering`` environment, several powerful software tools were put in place to facilitate extensive exploration of all aspects of the design. These tools include a simulation package, graphics package and an Expert System shell which have been integrated to provide an environment which encourages the close interaction of hardware and software engineers. This paper includes a description of the simulation, user interface, embedded software, remote procedure calls, and diagnostic software which together have enabled us to provide real-time control and monitoring of a working prototype switch-based data acquisition (DAQ) system.

Energy Technology Data Exchange (ETDEWEB)

Alumina (94 and 99.8% grade compositions) was brazed directly to itself with gold-based active brazing alloys (ABA's) containing vanadium additions of 1,2 and 3 weight percent. The effects of brazing conditions on the joint properties were investigated. Wetting behavior, interfacial reactions, microstructure, hermeticity and tensile strength were determined. Wetting was fair to good for the ABA and base material combinations. Microanalysis identified a discontinuous Al-V-O spinel reaction product at the alumina-braze interface. Tensile strength results for 94% alumina were uniformly good and generally not sensitive to the vanadium concentration, with tensile values of 85-105 MPa. There was more variability in the 99.8% alumina strength results, with values ranging from 25-95 MPa. The highest vanadium concentration (3 wt. %) yielded the highest joint strength for the brazed 99.8% alumina. Failures in the 99.8% ...

Science.gov (United States)

We describe a closed-loop brain-computer interface that re-ranks an image database by iterating between user generated 'interest' scores and computer vision generated visual similarity measures. The interest scores are based on decoding the electroencephalographic (EEG) correlates of target detection, attentional shifts and self-monitoring processes, which result from the user paying attention to target images interspersed in rapid serial visual presentation (RSVP) sequences. The highest scored images are passed to a semi-supervised computer vision system that reorganizes the image database accordingly, using a graph-based representation that captures visual similarity between images. The system can either query the user for more information, by adaptively resampling the database to create additional RSVP sequences, or it can converge to a 'done' state. The done state includes a final ranking of the image database and also ...

Energy Technology Data Exchange (ETDEWEB)

The Data Acquisition System for the CDMS II dark matter experiment was designed and built when the experiment moved to its new underground installation at the Soudan Lab. The combination of remote operation and increased data load necessitated a completely new design. Elements of the original LabView system remained as stand-alone diagnostic programs, but the main data processing moved to a VME-based system with custom electronics for signal conditioning, trigger formation and buffering. The data rate was increased 100-fold and the automated cryogenic system was linked to the data acquisition. A modular server framework with associated user interfaces was implemented in Java to allow control and monitoring of the entire experiment remotely.

Energy Technology Data Exchange (ETDEWEB)

Development Service Order {number_sign}90025 requested recommendations for computer hardware, operating systems, and software development utilities based on current and future SIMON software requirements. Since SIMON`s main objective is to be dispatched on missions by an operator with little computer experience, ``user friendly`` hardware and software interfaces are required. Other design criteria include: a fluid software development environment, and hardware and operating systems with minimal maintenance requirements. Also, the hardware should be expandable; extra processor boards should be easily integrated into the existing system. And finally, the use of well established standards for hardware and software should be implemented where practical.

International Nuclear Information System (INIS)

The symposium, Polycrystalline Thin Films - Structure, Texture, Properties, and Applications III, was held at the 1997 Materials Research Society Spring Meeting on March 31--April 4 in San Francisco, California. The topics and investigations were interdisciplinary in nature, and ranged from fundamental to technological. Specifically, the work presented in this volume includes film growth, texture and structural evolution, phase transformation, characterization of grain boundaries and interfaces, stress analysis, and works on polycrystalline Si and SiGe films and devices. Fifty four papers were processed separately for inclusion on the data base.

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) is a unique facility covering over 43 square miles. The Emergency Management and Response Office (EM&R) is required to respond, provide Incident Command (IC), and coordination for all Laboratory emergencies. This requires IC`s and support staff to respond to the actual scene of the incident. Since the IC is under numerous constraints and stress, the office wanted the capability of locating the EM&R vehicles on an electronic map. An automated vehicle location (AVL) system was required for the additional safety of the emergency response personal. The requirements for the AVL system include total automatic tracking and low cost. After careful consideration, it was determined that the most efficient and cost effective system would be based on packet radio technology as the transmission media. The location is determined by the Department of Defense Global Positioning System (GPS). The system that was designed and constructed ...

Science.gov (United States)

For abstract, see NSA 27 06, number 14465.

Science.gov (United States)

Cardiac Arrest; Cardiopulmonary Resuscitation

International Nuclear Information System (INIS)

The status of Monte Carlo system for the simulation of Bremsstrahlung in arbitrary decays and for the decay itself of #tau# -lepton is reviewed. During the last #tau# -lepton conference in 2010 several developments of the last two years have been presented: (i) For the TAUOLA Monte Carlo generator of #tau# -lepton decays, automated and simultaneous use of many versions of form-factors for the calculation of optional weights for fits was developed and checked to work in Belle and BaBar software environment. On-going work on alternative parameterizations of hadronic decays is presented too. (ii) The TAUOLA universal interface based on HepMC (the C++ event record) is now public. A similar interface for PHOTOS is now also public. (iii) Extension of PHOTOS Monte Carlo for QED Bremsstrahlung in decays featuring kernels based on complete first order matrix element are gradually becoming widely available thanks ...

Energy Technology Data Exchange (ETDEWEB)

Model-based approaches to pattern recognition and machine vision have been proposed to overcome the exorbitant training requirements of earlier computational paradigms. However, uncertainties in data were found to lead to a combinatorial explosion of the computational complexity. This issue is related here to the roles of a priori knowledge vs. adaptive learning. What is the a-priori knowledge representation that supports learning? I introduce Modeling Field Theory (MFT), a model-based neural network whose adaptive learning is based on a priori models. These models combine deterministic, fuzzy, and statistical aspects to account for a priori knowledge, its fuzzy nature, and data uncertainties. In the process of learning, a priori fuzzy concepts converge to crisp or probabilistic concepts. The MFT is a convergent dynamical system of only linear computational complexity. Fuzzy logic turns out to be ...

Science.gov (United States)

Recently, sustainable materials have attracted attention because of the need to alleviate environmental problems. Bamboo, in particular, has attracted attention as a sustainable material because it has the fastest natural growth rate among various natural materials. A self-bonding fiberboard using high quality bamboo fiber extracted with a machining center has been enabled to be fabricated by hot press forming. Therefore, we propose a sustainable manufacturing system that focuses on bamboo. An environmental impact of our system was evaluated by life cycle assessment (LCA), comparing with a glass fiber reinforced plastic production. Additionally, based on the LCA result, higher efficient fiber extraction process was proposed by an application of in-situ measurement of uninformed bamboo shape with irregularity.

British Library Electronic Table of Contents (United Kingdom)

Many real-world text classification tasks involve imbalanced training examples. The strategies proposed to address the imbalanced classification (e.g., resampling, instance weighting), however, have not been systematically evaluated in the text domain. In this paper, we conduct a comparative study on the effectiveness of these strategies in the context of imbalanced text classification using Support Vector Machines (SVM) classifier. SVM is the interest in this study for its good classification accuracy reported in many text classification tasks. We propose a taxonomy to organize all proposed strategies following the training and the test phases in text classification tasks. Based on the taxonomy, we survey the methods proposed to address the imbalanced classification. Among them, 10 common...

British Library Electronic Table of Contents (United Kingdom)

There is little flame spread data for homogeneous energetic materials and no data for nitramines. We report the results of flame spread experiments of PBX 9501 (HMX (cyclotetramethylenetetranitramine) based explosive). The horizontal flame spread rate, Sf, is of the same order of magnitude as normal deflagration and varies nearly as the square root of pressure, as our scaling analysis presented here predicts. In the vertical orientation, the flame propagation downward was observed to be slightly faster than horizontal flame spread, presumably because of the melt layer flowing downward on the sample. In an accident scenario, a charge may be fractured or the surface roughened. Consequently, we also examined the effect of roughness. Minor roughness created by explosives machining was found to...

British Library Electronic Table of Contents (United Kingdom)

Pitch-based short carbon fibers (CFs) were treated by air oxidation and cryogenic nitrogen, respectively. Thereafter the treated and untreated CFs were incorporated into polyimide (PI) matrix to form composites. The CFs before and after treatment were examined by XPS and SEM.The flexural strength of the specimen was determined in a three-point test machine and the tribological properties of PI composites sliding against GCr15 steel rings were evaluated on an M-2000 model ring-on-block test rig. The results show that the surface of the treated CFs became rougher. Lots of active groups formed on the CF surface after air oxidation.The treatment can effectively improve the mechanical and tribological properties in their PI composites due to the enhanced fiber-matrix interfacial bonding. Copyri...

Energy Technology Data Exchange (ETDEWEB)

Three holes the size of deposition holes (depth 7.5 m and diameter 1.5 m) were bored in the Research Tunnel at Olkiluoto, Finland. A novel full-face boring technique was used based on rotary crushing of rock and removal of crushed rock by vacuum flushing through the drill string. The purpose of the work was to demonstrate the feasibility of the technique. During the boring test procedures were carried out in order to determine the effect of changes in operating parameters on the performance of the boring machine and the quality of the hole. The boring method was found to be technically feasible and efficient. Evaluation of the quality of the hole included studies of the geometry of the hole, measurements of the surface roughness using a laser profilometer and study of excavation disturbances in the zone adjacent to the surface of the holes using two novel methods, He-gas diffusion and the {sup 14}C-polymethylmethacrylate methods. 43 refs.

Energy Technology Data Exchange (ETDEWEB)

Research highlights: {yields} Mathematical model represents a power system which consists of synchronous machine connected to infinite bus through transmission line. {yields} Power system stabilizer was designed based on optimal pole shifting controller. {yields} The system performances was tested through load disturbances at different operating conditions. {yields} The system performance with the proposed optimal pole shifting controller is compared with the conventional pole placement controller. {yields} The digital simulation results indicated that the proposed controller has a superior performance. -- Abstract: Power system stabilizer based on optimal pole shifting is proposed. An approach for shifting the real parts of the open-loop poles to any desired positions while preserving the imaginary parts is presented. In each step of this approach, it is required to solve a first-order or a second-order linear matrix ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the major features of the advisory tool `TUNDTEMP`, developed to act as a decision support in the continuous steel casting process. `TUNDTEMP` provides a means to predict abnormal phenomena of temperature origin in the casting that may be difficult to foresee in practical situations. The heart of the system is a semi-empirical calculation model that yields an estimate of the evolution of the tundish temperature of the liquid steel on the basis of a few important casting factors. The user interface of the system is to a large extent based on the visual presentation of the simulated results. The system also contains an optional rule based mechanism that provides assistance in the result interpretation and, if wished, linguistically formulates action recommendations. A separate program has been built for the tuning of the calculation model and for maintenance of the system. At the end of the report, the ...

International Nuclear Information System (INIS)

The thermal transformation of Al-base icosahedral phases was studied in-situ by real time neutron powder diffraction. Different compositions have been selected in order to vary the initial phase morphology and change the neutron scattering contrast between species. Alloys with low silicon and large aluminium contents produce first the orthorhombic O-Al_6Mn modification. In alloys with larger silicon content, the #alpha#-AlMnSi cubic phase appears soon after the beginning of the transformation but is still preceeded by O-Al_6Mn. Depending on compositions, the crystallization of the icosahedral phase is controlled either by the diffusion of Al through its interface with the residual fcc aluminium or that of Si within the bulk. The results are discussed in the light of current structural models. (author) 40 refs., 14 figs., 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

Emeraldine base (EB) polymer?ZnO nanoparticles composite films has been synthesized by solution casting technique on ITO-coated glass substrate and characterized by XRD, FTIR and TEM for their structure and morphology. Dielectric behaviour of these composite films has been investigated in the very low frequency region to medium frequency region (1?kHz?1?MHz). The dielectric constant of the composite with 30% nanoparticles is almost one-tenth of the pure EB. The dielectric value becomes constant in the frequency region greater than 400?kHz. The change in dielectric behaviour of the composite is explained on the basis of multilayered interface formed between the ZnO nanoparticles and emeraldine chains. Nanoparticles have high energy surface which is responsible for the decrease of free volum...

Energy Technology Data Exchange (ETDEWEB)

The adhesion of microorganisms onto materials surface mediated by extracellular polymeric substances (EPS) lead to an important modification of the metal-solution interface. The requirement of modern civilization with the heightened sense of environmental responsibilities and quality of life can be met by using some eco-friendly microbiocides with different spectra of activity. Some N{sub 2}O{sub 2} donor Schiff base compounds were synthesized and characterized by IR, NMR and ESR spectroscopy. These compounds were found effective in controlling the growth of biofilm of E. coli, Pseudomonas fluorescens and Thiobacillus thiooxidans on copper surface. The optimum concentration of these compounds are in the range of 1--10 ppm. Various electrochemical, microbiological and surface-analytical techniques were used to monitor the biofilm in the presence of microbiocides.

International Nuclear Information System (INIS)

The purpose of the present study is to develop a new method for chemical state analysis by means of EPMA(Electron probe microanalyser). The measured X-ray intensity of Si-K#beta# characteristic X-ray spectra were read-out by a 16 bit microcomputer with a RS-232C interface. And using the curve fitting method the quantitative analysis of chemical compositions in a ternary compound that constituted of the same element has been established. The present method was applied to analyse of the friction and wear properties of Si-base ceramics sliding materials. It was found that the wear debris contains both the compositions of the sliding materials and SiO_2, and the SiO_2 contents in wear debris was changed with relative humidity. The results clearly showed that the proposed method is very useful for determing the compositions in the ternary compound. (author).

CERN Document Server

This paper offers a conceptually straightforward method for the calculation of stresses in polarisable media based on the notion of a drive form and its property of being closed in spacetimes with symmetry. After an outline of the notation required to exploit the powerful exterior calculus of differential forms, a discussion of the relation between Killing isometries and conservation laws for smooth and distributional drive forms is given. Instantaneous forces on isolated spacetime domains and regions with interfaces are defined, based on manifestly covariant equations of motion. The remaining sections apply these notions to media that sustain electromagnetic stresses, with emphasis on homogeneous magnetoelectric material. An explicit calculation of the average pressure exerted by a monochromatic wave normally incident on a homogeneous, magnetoelectric slab in vacuo is presented and the concluding section summarizes how ...

Science.gov (United States)

Silicon carbide (SiC) based electronic devices are of great importance for applications under the condition of high temperature, high power and high radiation. Schottky diodes of Palladium/SiC are good candidates for hydrogen and hydrocarbon gas sensors at elevated temperature. The detection sensibility of the diodes has been found heavily temperature dependent. In this work, the electrical and chemical properties of Pd/SiC Schottky contacts were studied by XPS and AES at different annealing temperatures. Schottky diodes were made by depositing ultra-thin palladium films onto a silicon carbide substrate. No significant change in the Schottky barrier height of the Pd/SiC contact was found in the temperature range of 300-673K. Palladium diffusion into SiC and the formation of palladium silicides were observed at room temperature and became significant at 300^oC and higher temperature. The mechanism of diffusion and reaction at the Pd/SiC ...

Energy Technology Data Exchange (ETDEWEB)

The effect of interfacial structure on the mechanical properties of aluminum-ceramic composite materials fabricated by liquid phase sintering was studied. The composites were based on two matrix alloys (powder metallurgy alloys 201 and 601) reinforced with either Al{sub 2}O{sub 3} or SiC particulate. Characterization of the interfacial regions demonstrated that the SiC-matrix interfaces were faceted whereas the Al{sub 2}O{sub 3}-matrix interfaces had an incomplete layer of a silicon-rich amorphous phase. Preferential attack of the particles during sintering is believed to cause the crystallographic facets to form on SiC. Locally high silicon concentrations near Al{sub 2}O{sub 3} particles led to the formation of a glassy phase from the reduction of Al{sub 2}O{sub 3}. The difference in interfacial structure resulted in a higher particle-matrix bond strength and therefore improved composite mechanical properties in the ...

Energy Technology Data Exchange (ETDEWEB)

In order to understand the anodic behaviour of Al--Mo and Al--W amorphous alloys in the borate buffer electrolyte, samples of these alloys were polarized galvanostatically. The resultant anodic films were thicker than the passive films formed during potentiodynamic polarization enabling detailed examination of the films and alloy substrates by surface analytical methods. AES investigations suggest that the anodic films formed at low and moderate voltages on Al--Mo or Al--W amorphous alloys consist of Al-oxide, whereas refractory metals remain unoxidized and enriched at the film/substrate interface. Molybdenum and tungsten act as 'dissolution moderators', restraining the substrate dissolution process at the film/substrate interface. However, after anodization at high voltages (50 V), AES revealed the presence of an oxidized refractory metal in the inner part of the anodic film. Based on these results of ...

Energy Technology Data Exchange (ETDEWEB)

Electromechanical oscillations of small magnitude and low frequency exist in the interconnected power system and often persist for long periods of time. Power system stabilizers (PSSs) are traditionally used to provide damping torque for the synchronous generators to suppress the oscillations by generating supplementary control signals for the generator excitation system. Numerous techniques have previously been proposed to design PSSs but many of them are synthesized based on a linearized model. This paper presents a nonlinear power system stabilizer based on synergetic control theory. Synergetic synthesis of the PSS is based fully on a simplified nonlinear model of the power system. The dynamic characteristics of the proposed PSS are studied in a typical single-machine infinite-bus power system and compared with the cases with a conventional PSS and without a PSS. Simulation results show the proposed ...

Energy Technology Data Exchange (ETDEWEB)

The friction and wear properties of glass fiber reinforced composites of nylons (nylon 6, nylon 66 and nylon 46) with different crystallinities due to their molecular structures were investigated by sliding them with alumina ceramics and using a pin-on-disk friction machine. The friction coefficients of the glass fiber reinforced nylons in oil were lower and more stable than those in air from the initial stage of friction. The transfer of nylon matrix to adhere onto the alumina surface in air was so much greater than in oil that the alumina surface could not be recognized. Consequently, a different between the friction and wear properties in air and in oil was resulted. Reinforcement of nylons with glass fiber remarkably improved their friction properties in oil by its lubricating action, while the wears were rather high contrary to what was expected. This tendency was conspicuous for nylon 46 with high crystallinity. Breakage and extracting of glass fibers from ...

Science.gov (United States)

F4.1 . MONOTON. Increasing . FILLVAL ... Interface is easier-to-use and requires a much shorter learning curve than the Internal Interface, ...

Science.gov (United States)

The formation of palladium silicides near the interface may decrease hydrogen solubility at the effective metal/semiconductor ...

Energy Technology Data Exchange (ETDEWEB)

The boundary-integral equation method is well suited for the calculation of the dynamic-stiffness matrix of foundations embedded in a layered visco-elastic halfspace (or a transmitting boundary of arbitrary shape), which represents an unbounded domain. It also allows pile groups to be analyzed, taking pile-soil-pile interaction into account. The discretization of this boundary-element method is restricted to the structure-soil interface. All trial functions satisfy exactly the field equations and the radiation condition at infinity. In the indirect boundary-element method distributed source loads of initially unknown intensities act on a source line located in the excavated part of the soil and are determined such that the prescribed boundary conditions on the structure-soil interface are satisfied in an average sense. In the two-dimensional case the variables are expanded in a Fourier integral in the wave number domain, while in three ...

Science.gov (United States)

A 12-month program was conducted to advance the technology of the Electrical Discharge Machining (EDM) process to be applicable to the stringent requirements of gun barrel boring and rifling. The type of barrels employed in the test were .220 swift gun ba...

Energy Technology Data Exchange (ETDEWEB)

Thermo-hygro-rheology of wood-adhesive systems plays an important role during the hot pressing process of wood based composites. The principal objective of this research is to quantitatively study the thermo-hygro rheological characteristics of wood-adhesive systems used in such composites. This is with a view to providing material characteristics which may be used in simulation models of industrial hot-pressing operations. For this purpose, a specially designed miniature hot press system mounted on a servo-hydraulic testing machine was used to compress pre-formed fiber networks. The environment for each test was maintained uniform throughout the specimen by pre-treating it inside the system until the desired conditions of temperature and moisture were achieved. Experiments were conducted under a range of test conditions of load (1 to 6 MPa), temperature (25 to 150C) and moisture content (0 to 16%). A five-element rheological model was ...

International Nuclear Information System (INIS)

To increase further the accuracy of flow regime and considering the non-stationary characteristics of differential pressure fluctuation signals of gas-liquid two-phase flow, the flow regime identification method based on recurrence quantification analysis (RQA) and multi-sensor data fusion techniques is put forward. First of all, the recurrence quantification analysis method is used to extract the nonlinear feature parameters of the differential pressure fluctuation signals of gas-liquid two-phase flow, and data fusion of feature layer is conducted by QRA feature parameters of differential pressure signals of three pressure measure intervals, and composes the fusion feature vectors. The fused characteristic vector are input into the support vector machine for identify flow regime. The identification results for four typical flow regimes of air-water two-phase flow in horizontal pipe has shown that the reliability of the identification result is ...

CERN Document Server

Sparse learning has recently received increasing attention in many areas including machine learning, statistics, and applied mathematics. The mixed-norm regularization based on the L1/Lq norm with q > 1 is attractive in many applications of regression and classification in that it facilitates group sparsity in the model. The resulting optimization problem is, however, challenging to solve due to the structure of the L1/Lq -regularization. Existing work deals with special cases including q = 2,infinity, and they cannot be easily extended to the general case. In this paper, we propose an efficient algorithm based on the accelerated gradient method for solving the L1/Lq -regularized problem, which is applicable for all values of q larger than 1, thus significantly extending existing work. One key building block of the proposed algorithm is the L1/Lq -regularized Euclidean projection (EP1q). Our theoretical analysis reveals ...

International Nuclear Information System (INIS)

This paper presents a practical case study on the dynamic stability of the Saudi Electricity Company (SEC) power system and its effect on increasing power transfer limit of the interconnection between Eastern Operating Area (SEC-EOA). The problem of optimal tuning of the power system stabilizer parameters was converted into optimization problem wth eigenvalue-based objective functions, which was then solved by genetic algorithms. In this regard, two eigenvalue-based objective functions were considered and the problem is solved using real-coded genetic algorithm (RCGA). The effectiveness of the suggested technique to enhance the power system dynamic stability and to extend the power transfer capability limit of the SEC-EOA and the SEC-EOA power system was verified through a comprehensive eigenvalue analysis and time-domain nonlinear simulation. The results also indicated that the proposed tuning schemes of the existing stabilizers in the system ...

Energy Technology Data Exchange (ETDEWEB)

In the last two years, the VDMA work group 'Functional security' compiled a qualitative and quantitative procedure for the determination and evaluation of turbo-machine specific risks. With the calibrated risk graph for turbo-machines the requirements (Safety Integrity Level SIL) to the protective functions for turbo-machines (steam turbines, gas turbines, generators and compressors) were determined. With consideration of the legislation, the work group compiled a recommendation for the renewal and/or reconstruction of protective functions with old facilities.

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

China's propaganda machine seeks to control public opinion at all costs?-?and the media is its tool, writes David Bandurski

Wastenet

... Longer residence times attain finer grinds while shorter residence times attain higher outputs. Accordingly, the ATTOMILL can be set up to achieve optimum efficiency for individ ual applications. VENDOR INFORMATION: Peterson Machine Inc. www.microgrind.com/peterson/tech.htm Peterson Machine Inc. (formally Peterson North) was created under D. Peterson Machine & Fabrication Ltd. in 1994 after two years of successful ...

Science.gov (United States)

Nitrate microelectrodes and ORP microelectrodes were fabricated to study the denitrification characteristics of dynamic membrane at different COD loadings. The denitrification process was found at 0.6-1 mm depth beneath the interface of biofilm/bulk. The results of ORP microelectrode also demonstrated that the ORP value in the range of denitrification area was between 88.6 approximately -128.4 mV which was appropriate to denitrification. When the COD loading was 0.45 kg/(m3 x d), the denitrification rate (NO3- -N) was the maximum of 0.6347 x 10(-6 mol/(L x s). With the increase of COD loading, the denitrification area was increasing and two layers with different denitrification rates emerged in the dynamic membrane. The phenomenon implied the effect of organic concentration, oxygen concentration and bacterial competition on the denitrification rate. PMID:17117632

Energy Technology Data Exchange (ETDEWEB)

In this work, the pulse plasma nitriding process of pure iron is modelled using a kinetic model derived from the Fick's laws. This approach based on the error function model allows to simulate the growth kinetics of a biphase configuration consisting of {gamma}'-Fe{sub 4}N{sub 1-x} and {epsilon}-Fe{sub 2-3}N iron nitrides under specified conditions. By coupling the kinetics data about the diffusivities of nitrogen in {alpha}-Fe, {gamma}' and {epsilon} phases to the thermodynamic description of the Fe-N phase diagram, it is possible to evaluate the kinetic constant at each growing phase interface, the thickness of nitrided layer, and predict the nitrogen concentration profiles. The comparison between the experimental and theoretical results shows the reliability of the simulation results.

British Library Electronic Table of Contents (United Kingdom)

The age hardening behavior of Al-4.5%Cu alloy composite reinforced with zircon sand particulates and produced by stir casting route has been investigated in different quenching media viz, water, oil, and salt brine solution (7wt%). Optical microscopy of the as cast alloy composite indicates that the matrix of the composite has the cellular structure. Copper rich CuAl2 precipitates have been found near particle matrix interface. The results of ageing demonstrate that the microhardness of age hardenable Al-Cu based alloy composites depend on the quenching medium in which they are heat treated. Salt brine quenching is faster as compared to water and oil, even if higher strength is obtained but cannot be used for complex shapes and thin sections where oil quenching is the alternative due to mi...

International Nuclear Information System (INIS)

Strain embrittlement in Ti base alloys during tensile testing was investigated. Results show that in an #alpha#-#beta# titanium alloy the local activity of H in alpha phase (#alpha#/sub H//sup #alpha#) increases and activity of H in beta phase (#alpha#/sub H//sup #beta#) decreases as the equiaxed #alpha# particle size decreases at constant volume fraction of phases. Thus with decreasing particle size there would be a tendency for H to move from #alpha# to #beta#, decreasing the H content of #alpha#. Also whether H tended to move from #beta# to #alpha# or from #alpha# interiors to the #alpha#-#beta# interface this tendency would be reduced by surface tension effects, making the alloy less susceptible to embrittlement.

CERN Document Server

The physical foundations of a variety of emerging technologies --- ranging from the applications of quantum entanglement in quantum information to the applications of nonequilibrium bulk and interface phenomena in microfluidics, biology, materials science, energy engineering, etc. --- require understanding thermodynamic entropy beyond the equilibrium realm of its traditional definition. This paper presents a rigorous logical scheme that provides a generalized definition of entropy free of the usual unnecessary assumptions which constrain the theory to the equilibrium domain. The scheme is based on carefully worded operative definitions for all the fundamental concepts employed, including those of system, property, state, isolated system, environment, process, separable system, system uncorrelated from its environment, and parameters of a system. The treatment considers also systems with movable internal walls and/or semipermeable walls, with ...

British Library Electronic Table of Contents (United Kingdom)

Porous flow occurs in a wide range of materials and applies to many commercially relevant applications such as oil recovery, chemical reactors and contaminant transport in soils. Typically, breakthrough and pressure curves of column floods are used in the laboratory characterization of these materials. These characterization methods lack the detail to easily and unambiguously resolve flow mechanisms with similar effects at the core scale that can dominate at the aquifer or oil field scale, as well as the effects of geometry that control the flow at interfaces as in a perforated well or the inlet of an improperly designed column. Non-invasive imaging techniques such as MRI have been shown to provide a far more detailed characterization of the properties of the solid matrix and flow, but usu...

International Nuclear Information System (INIS)

A numerical analysis method for melting/solidification phenomena has been developed to evaluate a feasibility of several candidate techniques in the nuclear fuel cycle. Our method is based on the eXtended Finite Element Method (X-FEM) which has been used for moving boundary problems. Key technique of the X-FEM is to incorporate signed distance function into finite element interpolation to represent a discontinuous gradient of the temperature at a moving solid-liquid interface. Construction of the finite element equation, the technique of quadrature and the method to solve the equation are reported here. The numerical solutions of the one-dimensional Stefan problem, solidification in a two-dimensional square corner and melting of pure gallium are compared to the exact solutions or to the experimental data. Through these analyses, validity of the newly developed numerical analysis method has been demonstrated. (author)

International Nuclear Information System (INIS)

We have simulated the transient enhanced diffusion (TED) of boron fluoride (BF_2"+) implanted in crystalline and germanium amorphized silicon. Based on recently published models, the effect of fluorine on boron diffusion in silicon has been introduced and a modelling has been suggested. In order to simulate the boron experimental profiles, we have assumed that fluorine forms clusters involving interstitial boron which reduces the junction depth. Experimental results indicate that fluorine behaviour depends on amorphization energy. Moreover, even no germanium preamorphization is performed, silicon is still amorphized by fluorine species. Hence, BF_2"+ implantation leads to an amorphous/crystalline (a/c) interface near the surface. An improvement of published models is suggested taking into account fluorine effects. The simulations satisfactory reproduce the SIMS experimental profiles for a large scale of experimental conditions.

CERN Document Server

The LHCb experiment has chosen to use the SAM framework (Service Availability Monitoring Environment from EGEE-II) [1] make extensive tests of the LHCb environment at all the accessible grid resources. The availability and the proper definition of the local Computing and Storage Elements, user interfaces as well as the WLCG software environment are checked. The SAM framework is also used to pre-install the LHCb applications in the shared software area provided by each site. The deployment of the LHCb applications is based on a python tool developed inside the experiment. It is used for software management including incremental installation of interdependent packages and clean package removal. After the application software is installed a validation test of the whole MC chain is run. According to the results of the experiment specific SAM tests, the sites are (re)integrated into the LHCb production system managed by DIRAC [2]. The possibility of ...

Energy Technology Data Exchange (ETDEWEB)

Spectroscopy based on the Andreev reflection (AR) process at the interface between the normal metal tip and the superconductor has become one of the very successful methods for studies in novel exotic superconductors. The method is capable to address the size, symmetry as well as multiplicity of the superconducting order parameter. The method provided one of the first evidences of the two-gap superconductivity in MgB{sub 2} with a detailed temperature dependence of the both gaps. A theory treating the Andreev reflection spectroscopy in the mixed state is missing. We analyse the AR spectra of MgB{sub 2} in the mixed state via modelling the magnetic pair-breaking by the increasing spectral broadening parameter {gamma}. As a result a non-trivial pair breaking effect in the {pi}-band is found.

CERN Document Server

We present an approach to automatically generate interfaces supporting personalized interaction with digital libraries; these interfaces augment the user-DL dialog by empowering the user to (optionally) supply out-of-turn information during an interaction, flatten or restructure the dialog, and enquire about dialog options. Interfaces generated using this approach for CITIDEL are described.

Energy Technology Data Exchange (ETDEWEB)

The Internet is becoming the preferred method for disseminating scientific data from a variety of disciplines. This can result in information overload on the part of the scientists, who are unable to query all of the relevant sources, even if they knew where to find them, what they contained, how to interact with them, and how to interpret the results. A related issue is keeping up with current trends in information technology often taxes the end-user's expertise and time. Thus instead of benefiting from this information rich environment, scientists become experts on a small number of sources and technologies, use them almost exclusively, and develop a resistance to innovations that can enhance their productivity. Enabling information based scientific advances, in domains such as functional genomics, requires fully utilizing all available information and the latest technologies. In order to address this problem we are developing a end-user centric, ...

Science.gov (United States)

One of the requirements for a federated information system is interoperability, the ability of one computer system to access and use the resources of another system. This feature is particularly important in biomedical research systems, which need to coordinate a variety of disparate types of data. In order to meet this need, the National Cancer Institute Center for Bioinformatics (NCICB) has created the cancer Common Ontologic Representation Environment (caCORE), an interoperability infrastructure based on Model Driven Architecture. The caCORE infrastructure provides a mechanism to create interoperable biomedical information systems. Systems built using the caCORE paradigm address both aspects of interoperability: the ability to access data (syntactic interoperability) and understand the data once retrieved (semantic interoperability). This infrastructure consists of an integrated set of three major components: a controlled terminology service (Enterprise ...

Energy Technology Data Exchange (ETDEWEB)

The procedure was developed to enable STUK (Radiation and Nuclear Safety Authority) to make simplified estimates on off-site consequences based on the existing results of the PSA level 2 calculations done by e.g. power utilities. Method is based on dose calculated from each nuclide group of reactor activity inventory when the same release fraction for each group is assumed. This means that a specific new result from PSA level 2 can be categorised to find out a representative PSA level 3 result for this case. In addition a user interface including the procedure was prepared. Secondly some new insights about consequences based on the releases from PSA level 2 is expected to give better understanding of risks at prevailing increased reactor power levels. In this case only some early health effects and long-term doses were estimated without full-scope PSA level 3 approach. (orig.)

International Nuclear Information System (INIS)

In this study, dissimilar welds between HP heat-resistant steel and Incoloy 800 were made with four different filler materials including: 309 stainless steel and nickel-based Inconel 82, 182 and 617. The microstructure of the base metals, weld metals and their interfaces were characterized by utilizing optical and scanning electron microscopy. Grain boundaries migration in the weld metals was studied. It was found that the migration of grain boundaries in the Inconel 82 weld metal was very extensive. Precipitates of TiC and M_2_3C_6 (M = Cr and Mo) in the Inconel 617 weld metal are identified. The necessary conditions for the formation of cracks close to the fusion line of the 309-HP joints are described. Furthermore unmixed zone near the fusion line between HP steel base metal and Inconel 82 weld metal is discussed. An epitaxial growth is characterized at the fusion line of the 309-Alloy 800 and ...

Energy Technology Data Exchange (ETDEWEB)

New furnaces were built based on fused silica with NiChrome heating elements custom-wound on alumina ceramic to self-compensate for induced magnetic fields during operation. During tests these furnaces failed due to thermal stresses caused by the high temperature cement used to hold the alumina ceramic in place. As a third solution pieces of boron nitride have been procured from which new furnace bodies will be machined during the third quarter. In order to increase the in-house capacity for machining ceramic parts a small lathe was ordered. The implementation of the LabView data acquisition software from National Instruments, Inc. took more time than anticipated and is still not completed. Major difficulties had to be overcome during the integration of the separate positive and negative high voltage supplies ({plus_minus}1000V). It became apparent that a custom-designed switch had to be installed to safeguard the data ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this investigation was to simulate a machining front from an abrasive waterjet and its movements in a ceramic material. Wear factors affecting the abrasive waterjet nozzle were also to be established. Therefore, a low inclination angle (9[degree]) was used between the nozzle and test sample, simulating a moving machine front. A standard nozzle with an inner diameter of 0.76 mm was used in the test, and it was placed close to the samples. The outer diameter of the abrasive nozzle was 9.5 mm. The high wear rate from abrasive waterjets makes it possible to machine hard ceramics-including dense alumina, titanium boride, silicon nitride, and composites-at high machining speeds.

International Nuclear Information System (INIS)

As an engineered barrier system in the geological disposal of high-level waste, multibarrier system is considered. Multibarrier system consists of the vitrified waste, the overpack and the buffer. Bentonite is one of the potential material as the buffer because of its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. As the construction technology of the buffer, the block installation method and in-situ compaction method, etc, are being investigated. The block installation method is to emplace the buffer blocks manufactured in advance at the ground facility, and construction processes of the block installation method at the underground will be simplified compared with the in-situ compaction method. However, the block joints of buffer might be a mechanical weak portion or might be a preferential flow channel. ...

Energy Technology Data Exchange (ETDEWEB)

After several years of planning and workshop meetings, a decision was reached in late 2008 to organize PICMG xTCA for Physics Technical Subcommittees to extend the ATCA and MTCA telecom standards for enhanced system performance, availability and interoperability for physics controls and applications hardware and software. Since formation in May-June 2009, the Hardware Technical Subcommittee has developed a number of ATCA, ARTM, AMC, MTCA and RTM extensions to be completed in mid-to-late 2010. The Software Technical Subcommittee is developing guidelines to promote interoperability of modules designed by industry and laboratories, in particular focusing on middleware and generic application interfaces such as Standard Process Model, Standard Device Model and Standard Hardware API. The paper describes the prototype design work completed by the lab-industry partners to date, the timeline for hardware releases to PICMG for approval, and the status of the software ...

Science.gov (United States)

The surveillance systems have been widely used in automatic teller machines (ATMs), banks, convenient stores, etc. For example, when a customer uses the ATM, the surveillance systems will record his/her face information. The information will help us understand and trace who withdrew money. However, when criminals use the ATM to withdraw illegal money, they usually block their faces with something (in Taiwan, criminals usually use safety helmets or masks to block their faces). That will degrade the purpose of the surveillance system. In previous work, we already proposed a technology for safety helmet detection. In this paper, we propose a mask detection technology based upon automatic face recognition methods. We use the Gabor filters to generate facial features and utilize geometric analysis algorithms for mask detection. The technology can give an early warning to save-guards when any "customer" or "intruder" blocks his/her face information ...

Energy Technology Data Exchange (ETDEWEB)

Silica and bridged polysilsesquioxane aerogels are low-density materials that are attractive for applications such as thermal insulation, porous separation media or catalyst supports, adsorbents, and cometary dust capture agents. However, aerogels are notoriously weak and brittle making it difficult to handle and machine monoliths into desired forms. This complication prevents the development of many applications that would otherwise benefit from the use of the low-density materials. Here, we will describe our efforts to chemically modify and mechanically enhance silica-based aerogels using chemical vapor techniques without sacrificing their characteristic low densities. Monolithic silica and organic-bridged polysilsesquioxane aerogels were prepared by sol-gel polymerization of the respective methoxysilane monomers followed by supercritical carbon dioxide drying of the gels. Then the gels were reactively modified with silylating agents to ...

Energy Technology Data Exchange (ETDEWEB)

number of technical requirements and performance criteria can drive stellarator costs, e.g., tight tolerances, accurate coil positioning, low aspect ratio (compactness), choice of assembly strategy, metrology, and complexity of the stellarator coil geometry. With the completion of a seven-year design and construction effort of the National Compact Stellarator Experiment (NCSX) it is useful to interject the NCSX experience along with the collective experiences of the NCSX stellarator community to improving the stellarator configuration. Can improvements in maintenance be achieved by altering the stellarator magnet configuration with changes in the coil shape or with the combination of trim coils? Can a mechanical configuration be identified that incorporates a partial set of shaped fixed stellarator coils along with some removable coil set to enhance the overall machine maintenance? Are there other approaches that will simplify the concepts, improve access for ...

Energy Technology Data Exchange (ETDEWEB)

A spectral element method embodying Large Eddy Simulation based on Re- Normalization Group theory for simulating Sub Grid Scale viscosity was chosen for this work. This method is embodied in a computer code called NEKTON. NEKTON solves the unsteady, 2D or 3D,incompressible Navier Stokes equations by a spectral element method. The code was later extended to include the variable density and multiple reactive species effects at low Mach numbers, and to compute transport of large particles governed by inertia. Transport of small particles is computed by treating them as trace species. Code computations were performed for a number of test conditions typical of flow past a deep tube bank in a boiler. Results indicate qualitatively correct behavior. Predictions of deposition rates and deposit shape evolution also show correct qualitative behavior. These simulations are the first attempts to compute flow field results at realistic flow Reynolds numbers of the order of ...

Energy Technology Data Exchange (ETDEWEB)

In machine condition monitoring many fault-related vibration signals are highly non-stationary. Time-frequency representations comprise the natural signal-processing tool traditionally used for representing such non-stationary signals. The methods used in this analysis are based on the second order statistics of a signal. This paper discusses the use of higher order time frequency methods in the context of a condition monitoring application. The paper outlines the two classes of higher order representations: the L-Wigner distribution and the sliced Wigner higher order distribution. The use of higher order distributions introduces the possibility of non-oscillating cross-terms, a problem not encountered in conventional bilinear time-frequency methods. Techniques for reducing these cross-terms are presented. The paper compares the performance of bilinear and higher order time-frequency methods using synthetic data and vibration signals measured ...

Energy Technology Data Exchange (ETDEWEB)

A newly developed discrete-time adaptive sliding mode power system stabilizer (PSS) is proposed in this paper. Because the proposed PSS is developed in the pure discrete-time domain it is able to maintain the stability with the rather slower smapling frequency compared to discretized conventional continuous-time sliding mode PSS. The proposed PSS has the three main superiorities to the conventional PSS. First, because the proposed PSS utilizes the sliding mode control method, it has the strong robustness to the variations of the system parameters. Hence, it can overcome the minor disturbances such as identification errors, modeling errors, etc. Second, the proposed PSS needs only input/output measurements as feedback signals. Hence, it does not need the measurements of the state variables as the conventional sliding mode PSS or PSS based on the linear quadratic control method does. Finally, because the proposed PSS have the adaptive property, it is able to overcome ...

Energy Technology Data Exchange (ETDEWEB)

This report describes a microcomputer-based, single-project financial analysis program: BREEDER. BREEDER is a user-friendly model designed to facilitate frequent and rapid analyses of the financial implications associated with alternative design and financing strategies for electric generating plants and large-scale prototype breeder (LSPB) reactors in particular. The model has proved to be a useful tool in establishing cost goals for LSPB reactors. The program is available on floppy disks for use on an IBM personal computer (or IBM look-a-like) running under PC-DOS or a Kaypro II transportable computer running under CP/M (and many other CP/M machines). The report documents version 1.5 of BREEDER and contains a user's guide. The report also includes a general overview of BREEDER, a summary of hardware requirements, a definition of all required program inputs, a description of all algorithms used in performing the construction-period ...

International Nuclear Information System (INIS)

This paper begins with an introduction to Guangdong Daya Bay Nuclear Power Station (GNPS) and gives a simple introduction to the operations and maintenance documentation system at GNPS. It then will review the maintenance program guidelines base and the associated problems prior to the application of reliability centered maintenance (RCM). How RCM was implemented at GNPS, how the results of RCM analysis were used to optimize the maintenance program and test program, and what is the interface between RCM and the existing maintenance program will be shown. Next, it will show the successful implementation of RCM at GNPS resulted in the following changes: A new understanding of equipment failure challenges operations and maintenance beliefs, maintenance concepts undergo a large change, maintenance program and periodic testing program are continuously modified and optimized, new on-condition maintenance technologies are introduced, non-productive ...

International Nuclear Information System (INIS)

This patent describes an expert overseer for the operation and real-time management of a mass spectrometer and associated laboratory equipment. The overseer is a computer-based expert diagnostic system implemented on a computer separate from the dedicated computer used to control the mass spectrometer and produce the analysis results. An interface links the overseer to components of the mass spectrometer, components of the laboratory support system, and the dedicated control computer. Periodically, the overseer polls these devices and as well as itself. These data are fed into an expert portion of the system for real-time evaluation. A knowledge base used for the evaluation includes both heuristic rules and precise operation parameters. The overseer also compares current readings to a long-term database to detect any developing trends using a combination of statistical and heuristic rules to evaluate the results. The ...

Energy Technology Data Exchange (ETDEWEB)

In the upgrade project of the Beijing Electron-Positron Collider (BEPCII), a novel Detector-Control System (DCS) for the Beijing Spectrometer (BESIII) has been built and started its successful operation for the BESIII Commissioning. The main task of the DCS is to monitor and control the status of the BESIII detector and to guarantee a safe operation of the detector. The DCS must provide a uniform and coherent interface to detector operators even though there are a large number of distributed I/O channels from a large variety of equipments. For this reason, the DCS is hierarchically organized and divided into three layers: front-end layer (FEL), local control layer (LCL) and global control layer (GCL). In the FEL, devices ranging from simple sensors up to complex computer-based devices like embedded systems and programmable logical controllers (PLC) are utilized. A LabVIEW-based software framework has been developed for the ...

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) Headquarters and associated contractors have developed an IBM PC-based software package that estimates costs, schedules, and public and occupational health risks for a range of mixed-waste management options. A key application of the software package is the comparison of various waste-treatment options documented in the draft Site Treatment Plans prepared in accordance with the requirements of the Federal Facility Compliance Act of 1992. This automated Systems Analysis Methodology consists of a user interface for configuring complexwide or site-specific waste-management options; calculational algorithms for cost, schedule and risk; and user-selected graphical or tabular output of results. The mixed-waste management activities modeled in the automated Systems Analysis Methodology include waste storage, characterization, handling, transportation, treatment, and disposal. Analyses of treatment options identified ...

Energy Technology Data Exchange (ETDEWEB)

The Advanced Photon Source consists of five accelerators. The injection timing system provides the signals required to cause a bunch emitted from the electron gun to navigate through intermediate accelerators to a specific bucket (1 out of 1296) within the storage ring. Two linacs and a positron accumulator ring operate at 60Hz while a booster synchrotron ramps and injects into the storage ring at 2Hz. The distributed, modular VME/VXI-based injection timing system is controlled by two EPICS-based input/output controllers (IOCs). Over 40 VME/VXI cards have been developed to implement the system. Card types range from 352MHz VXI timing modules to VME-based fiber optic fanouts and logic translators/drivers. All timing is distributed with fiber optics. Timing references are derived directly from machine low-level rf of 9.77MHz and 352MHz. The timing references provide triggers to programmable delay ...

International Nuclear Information System (INIS)

Focused ion beam (FIB) microscopes have become well-established in the semiconductor industry during the past decade, and are rapidly gaining attention in the field of materials science, both as a tool for producing site specific, parallel sided transmission electron microscope (TEM) specimens and as stand alone specimen preparation and imaging systems. FIB secondary electron imaging (SEI) of nickel-based alloys, such as commercially produced Alloy 600 (approximately Ni 15Cr 10Fe 0.5C), has been demonstrated to show a high degree of sensitivity to the presence of deformation in the alloy, and FIB secondary ion imaging (SII) is particularly useful for identifying the presence of grain boundary corrosion, as secondary ion yields from metallic specimens can increase by three orders of magnitude in the presence of oxygen. This 'oxygen enhanced yield', makes FIB SII ideal for detection of corrosion at grain boundaries down to thicknesses of only a few tens of ...

Science.gov (United States)

Automatic weapons such as machine guns and submachine guns are found in the German-speaking region only in special army and police units and appear accordingly rarely in homicides, suicides and accidents. In the following, the findings in two cases of death with the use of machine and submachine guns are presented. The first case was a fatal accident during shooting on a training area (current machine gun of the German army, calibre 7.62 x 51 mm), the second case was a killing during a physical conflict (submachine gun MP 40 from World War II, calibre 9 x 19 mm). In the case with the machine gun autopsy disclosed typical entry holes corresponding to the calibre, but unusually large exit wounds with tissue bridges in the wound ground, measuring 4 x 2.5 cm in diameter. By contrast, the second case (submachine gun) showed "normal" entry and exit wounds. The differences are mainly caused by deviating ...

Energy Technology Data Exchange (ETDEWEB)

This paper addresses one source of degradation in OPV devices: the metal/organic interface. The basic approach was to study the completed device stability vs. the stability of the organic film itself as shown in subsequent devices fabricated from the films.

Energy Technology Data Exchange (ETDEWEB)

Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.

International Nuclear Information System (INIS)

Gallium liquid-metal ion sources that have been introduced in the late 1970s have allowed the development of a new class of micro- and nanofabrication tools collectively denominated as focused ion beam (FIB) machines. To investigate the potential of a helium beam in such a FIB instrument the authors have tested a room-temperature electron beam ion trap coupled with a high resolution FIB machine. In this letter they present their first results in target imaging using a helium beam with a resolution that allows to account for a beam diameter in the submicrometer range.

Energy Technology Data Exchange (ETDEWEB)

A gelcasting composition has improved drying behavior, machinability and shelf life in the dried and unfired state. The composition includes an inorganic powder, solvent, monomer system soluble in the solvent, an initiator system for polymerizing the monomer system, and a plasticizer soluble in the solvent. Dispersants and other processing aides to control slurry properties can be added. The plasticizer imparts an ability to dry thick section parts, to store samples in the dried state without cracking under conditions of varying relative humidity, and to machine dry gelcast parts without cracking or chipping. A method of making gelcast parts is also disclosed.

British Library Electronic Table of Contents (United Kingdom)

The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of-this planning guide is to present the process used to identify, document, and control PFP Stabilization and Deactivation Project interfaces. Revisions to this document will include, as attachments, the most recent version of the Project Interface Management List. A preliminary Interface Management List is included in Appendix A. This document is intended be a Project owned management tool. As such, this document will periodically require revisions resulting from improvements of the information, processes, and techniques as now described. For most revisions that suggest improved processes, PFP management approval is all that will be required.

International Nuclear Information System (INIS)

This article considers the application of simple trial wave functions to calculate the ground state energy of a hydrogen-like center near the interface of two media. Calculations have been performed taking into account the image potential. It has been shown that different kinds of wave functions are optimal at different distances from the interface. A relatively simple wave function has been suggested to represent main features of the dependence of the ground state energy on the distance to the interface. (authors)

Science.gov (United States)

... In 1982 an acousto-optic spectrum analyzer incorporated ... the OPTIMP is the optically controlled optical ... switch that changes the intensity reflectance ...

Science.gov (United States)

... in artificial intelligence, human physiology and biomedical prosthesis. ... central and peripheral nerve systems [1 ... CMOS circuit interface for multiplexed ...

Energy Technology Data Exchange (ETDEWEB)

Transient enhanced diffusion (TED) and dose loss (pile-up) are investigated for phosphorus-implanted samples covered with both oxide and nitride films. P ions were implanted into p-type (1 0 0) CZ-Si (dose 5x10{sup 13} cm{sup -3}, 100 keV) through a chemical vapor deposition (CVD) Si{sub 3}N{sub 4} film. For a half of samples, Si{sub 3}N{sub 4} was etched off and SiO{sub 2} films were grown by CVD. Both samples were annealed for 20-360 min at 700 deg. C. Diffusivity of P and the dose loss were estimated based on the secondary-ion mass spectrometry (SIMS) P profiles. Both Si/Si{sub 3}N{sub 4} and Si/SiO{sub 2} interfaces were investigated with transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS). There is no significant difference in P diffusivity between the SiO{sub 2} and Si{sub 3}N{sub 4} films for the present annealing condition of 700 deg. C for 20-360 min. Regarding dose loss, a distinct different behavior ...

Science.gov (United States)

we have a colloquium scheduled. Computing: register your machine and check our network security and visitor computer policies. For Our Information: Once arranged, please let us...

Energy Technology Data Exchange (ETDEWEB)

This paper deals with an experimental study of ultra-precision diamond cutting of magnesium alloy (AZ31). In order to investigate the machinability such as the cutting force and the surface integrity and understand the problems in a micro cutting, the experiments on the diamond cutting of magnesium alloy and pure aluminum with an ultra-precision turning machine has been carried out. The machinability of magnesium alloy was compared with that of pure aluminum and discussed. Consequently, both the thrust force component and the surface roughness obtained by cutting of magnesium alloy became larger than that of pure aluminum. It was also found that the inclusions or the defects in the work material caused to generate the scratches on the finished surface and influenced the integrity of mirror surface. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Officials of Saturn Machine and Welding Co., describe the company's designs of oven door, door cleaner and jamb cleaner and report performance at US coking plants.

Energy Technology Data Exchange (ETDEWEB)

In this project, graphite is used as a substitute for lead in order to maintain the machinability of plumbing components at the level of leaded brass. Graphite dispersed in Cu alloy was observed to impart good machinability and reduce the sizes of chips during machining of plumbing components in a manner similar to lead. Copper alloys containing dispersed graphite particles could be successfully cast in several plumbing fixtures which exhibited acceptable corrosion rate, solderability, platability, and pressure tightness. The power consumption for machining of composites was also lower than that of the matrix alloy. In addition, centrifugally cast copper alloy cylinders containing graphite particles were successfully made. These cylinders can therefore be used for bearing applications, as substitutes for lead-containing copper alloys. The results indicate that copper graphite alloys developed under this ...

Science.gov (United States)

airborne separation assistance systems (ASAS) to ... operations should be limited to the outer traffic flow ...... AGARD Meeting on Machine Intelligence in Air ...

Science.gov (United States)

We study a kinetic model for a system of two species of particles interacting via a repulsive long range potential and with a reservoir at fixed temperature. The interaction between the particles is modeled by a Vlasov term and the thermal bath by a Fokker-Planck term. We show that in the diffusive and sharp interface limit the motion of the interfaces at low temperature is described by a Stefan problem or a Mullins-Sekerka motion, depending on the time scale.

Science.gov (United States)

A critical element of a retinal prosthesis is the stimulating electrode array, which is placed in close proximity to the retina. It is via this retinal-electrode interface that a retinal prosthesis electrically stimulates nerve cells to produce the perception of light. The impedance load seen by the current driver consists of the tissue resistance and the complex electrode impedance. The results in this paper show that the tissue resistance of the retina is significantly greater than that of the vitreous humor in the eye. Circuit models of the electrode-retina interface are used to parameterize the different contributors to the overall impedance.

CERN Document Server

substrate). Within each group of simulations, three lubricant film thicknesses are studied to examine the effect of varying lubricant thickness. Statistical data are collected from each simulation and presented in this work. Via these data, together with the evolution, of atomic and molecular configurations, a very detailed picture of the properties of this thin film interface is presented. In particular, we conclude that perfluoropolyether lubricant forms distinct molecular layers when confined between two substrates, the rate of heat generation under shearing conditions typical of those in a head-disk interface is insufficient for thermal mechanisms to result directly in lubricant degradation, and mechanical stresses attained in the head-disk interface are unlikely to result in any significant degree of lubricant degradation. This thesis examines the tribology of a head-disk interface in an operating ...

International Nuclear Information System (INIS)

GaInP solar cell interfaces were characterized by admittance spectroscopy. Admittance spectroscopy is shown to be sensitive to the band structure at the heterojunction interfaces. In particular, a correlation between activation energy of the capacitance step in a capacitance versus temperature plot and effective potential barrier for majority carriers is demonstrated, indicating a new method for the determination of potential barriers at heterointerfaces. Using this technique, the effective potential barrier for holes at the p-Al_0_._5_3In_0_._4_7P/p-GaAs interface is found to be equal to 0.6 eV. Effects of interface defects and spreading resistance in the emitter of solar cells are illustrated and discussed.

Energy Technology Data Exchange (ETDEWEB)

From the alkalised crude extract of Symphytum cordatum (L.) W.K. roots, pyrrolizidine alkaloids (PAs) were extracted as free tertiary bases and polar N-oxides in a merely one-step liquid-liquid partitioning (LLP) in separation funnel and subsequently pre-fractionated by preparative multiple-development (MD) thin-layer chromatography (TLC) on silica gel plates. In this way three alkaloid fractions of different polarities and retention on silica gel plates were obtained as: the most polar N-oxides of the highest retention, the tertiary bases of medium retention, and diesterified N-oxides of the lowest retention. The former fraction was reduced into free bases by sodium hydrosulfite and purified by LLP on Extrelut-NT3 cartridge. It was further analysed together with the two other fractions by high-performance liquid chromatography (HPLC)-ion-trap mass spectrometry with atmospheric pressure chemical ionization (APCI) ...

Energy Technology Data Exchange (ETDEWEB)

This article describes a flexible and extensible infrastructure for applying Web-Technologies to embedded systems.The presented approach develops a Three-level-Architecture consisting of the embedded system, the universal Remote-Access-Server and the Remote-Access-Client. A system-spanning general interface allows the binding of embedded systems in order to access their process data. Additionally, this procedure facilitates a flexible processing of the device data, so that it is ready to be used by different control devices. To ensure flexibility - connecting different devices on the one side and providing information for different clients like PC, PDA or mobile phone on the other side - a new XML-based description language (Service Description Markup Language - SDML) is introduced. The SDML documents contain information about connected embedded systems, reusable device data and the presentation policies for different clients. These documents ...

Energy Technology Data Exchange (ETDEWEB)

In the Institute for Atomic Energy, Rikkyo University, just after the TRIGA-2 research reactor of 100 kW has attained the criticality, the cylindrical box for neutron radiography (NR) irradiation was made in the attached pool, and the research on NR was started in 1961. Thereafter in 1985, the vertical irradiation pipe was installed in the reactor tank, and the experiment for collecting the basic data was begun. In 1986, based on the obtained data, the NR irradiation facility on full scale was installed in No. 2 tangential horizontal experimental hole. As the main NR irradiation facilities, the vertical neutron irradiation pipe, the use of which is stopped now, the NR facility using the horizontal experimental hole (RUR/N2), the irradiation facility and ancillary facilities such as beam shutter, beam catcher and hoist are described. As the main equipments for NR, the imaging apparatuses of cooled type CCD, SIT and superhigh sensitivity, the image processors of ...

Energy Technology Data Exchange (ETDEWEB)

We have simulated the transient enhanced diffusion (TED) of boron fluoride (BF{sub 2}{sup +}) implanted in crystalline and germanium amorphized silicon. Based on recently published models, the effect of fluorine on boron diffusion in silicon has been introduced and a modelling has been suggested. In order to simulate the boron experimental profiles, we have assumed that fluorine forms clusters involving interstitial boron which reduces the junction depth. Experimental results indicate that fluorine behaviour depends on amorphization energy. Moreover, even no germanium preamorphization is performed, silicon is still amorphized by fluorine species. Hence, BF{sub 2}{sup +} implantation leads to an amorphous/crystalline (a/c) interface near the surface. An improvement of published models is suggested taking into account fluorine effects. The simulations satisfactory reproduce the SIMS experimental profiles for a large scale of experimental ...

Energy Technology Data Exchange (ETDEWEB)

The growth of SrBi{sub 2}Ta{sub 2}O{sub 9} (SBT) films on top of Pt electrode substrates is an important issue for the fabrication of ferroelectric based memories. In a recent publication, SBT thin films grown using seeded and unseeded procedures were studied by PIXE and RBS. Difficulties and misfits found in the comparison of results from both techniques were, at that time, overcome by physical considerations. These, although not rendering interpretation impossible, left out the possibility of understanding the exact nature of the differences between the interface behavior in each case. In the present work it is shown that the reanalysis of the same data using the recently developed RBS-PIXE simultaneous and self-consistent calculation present in NDF leads to stronger conclusions on the solid state reaction occurring during the deposition stage for both types of samples. Allowing for the occurrence of solid state reactions between the ...

Energy Technology Data Exchange (ETDEWEB)

This Current Year Work Plan presents a detailed description of the activities to be performed by the Joint Integration Office during FY87. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance, task monitoring, information gathering and task reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of program status reports for DOE. Program Analysis is ...

Energy Technology Data Exchange (ETDEWEB)

The leakage current behaviors of PLZT capacitors with top electrodes of Pt, Ir, and IrO{sub 2} are investigated before and after hydrogen forming gas anneal. The P-E hysteresis and fatigue properties of Pt/PLZT/Pt capacitors are almost recovered after recovery anneal in O{sub 2} ambient. The leakage current mechanisms of PLZT capacitors with Pt and IrO{sub 2} top electrodes are consistent with space-charge influenced injection model showing the strong time dependence irrespective of annealing conditions. On the other hand, the leakage current behavior of Ir/PLZT/Pt capacitor shows steady state independent of time because IrPb, conducting phase, formed at interface between Ir top and PLZT is a high conduction path. Teh leakage current mechanism of Ir/PLZT/Pt capacitor is consistent with Schottky barrier model. (author). 15 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

Embedded systems have become integral parts of a diverse range of systems from automobiles to critical infrastructure applications such as gas and electric power distribution. Unfortunately, research on computer security in general and intrusion detection in particular, has not kept pace. Furthermore, embedded systems, by their very nature, are application specific and therefore frameworks for developing application-specific intrusion detection systems for distributed embedded systems must be researched, designed, and implemented. In this paper, we present a configurable middleware-based intrusion detection framework. In particular, this paper presents a system model and a concrete implementation of a highly configurable intrusion detection framework that is integrated into MicroQoSCORBA, a highly configurable middleware framework developed for embedded systems. By exploiting the application-specific logic available to a middleware framework (e.g., object ...

CERN Document Server

Comparison of programming languages is a common topic of discussion among software engineers. Few languages ever become sufficiently popular that they are used by more than a few people or find their niche in research or education; but professional programmers can easily use dozens of different languages during their career. Multiple programming languages are designed, specified, and implemented every year in order to keep up with the changing programming paradigms, hardware evolution, etc. In this paper we present a comparative study between ten programming languages: Haskell, Java, Perl, C++, AspectJ, COBOL, Ruby, PHP, Bash Scripts, and Scheme; with respect of the following criteria: Secure programming practices, web applications development, web services design and composition, object oriented-based abstraction, reflection, aspect-orientation, functional programming, declarative programming, batch scripting, and user interface prototype ...

International Nuclear Information System (INIS)

Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to considerable investigation of the mechanism of corrosion and for palliatives. The basic mechanism is now fairly well understood. Chloride present in the boiler feedwater from condenser leakage is concentrated in the support plate crevice as a result of the superheat present. This leads to the formation of a low pH acid ferrous chloride environment either through the hydrolysis of a weak base chloride such as MgCl_2 or the combined action of a neutral chloride with an oxidizing agent. Rapid attack of the carbon steel ensues with the Fe_3O_4 corrosion product forming at the metal/oxide interface. This oxide has a volume approximately twice that of the steel consumed and thus eventually fills the crevice between the tube and the support plate. Oxide growth continues leading to compression of the Alloy 600 primary tube ...

Science.gov (United States)

Flow structures and heat transfer at the liquid-liquid interface are investigated experimentally and analytically in the entrance region of a liquid metal-water stratified flow in a horizontal rectangular channel. The two-equation model and the mixing length mode, including a damping turbulent region near the interface, are used to obtain analytical results for pressure drop, position of the interface, and heat transmission coefficients across the interface. Analytical results are compared with experimental results. Conclusions are presented and include the following: (1) vertical position of the interface increases or decreases along the stream according to the fluid flow rate of both fluids, and then approaches a constant value in the fully developed region; (2) pressure drop increases along the stream from the minimum value at the inlet; and (3) heat transmission coefficients ...

International Nuclear Information System (INIS)

With the deposition of PVD hard coatings on the tools applied in machining operations it is possible to achieve significant improvements in the performance and quality of the machining processes. Depending on the machined material and the operating principle, e.g. turning, milling or drilling, not only different machining parameters but also different coating materials are necessary. In interrupted cut machining of tempered steel, for example, the life time of Ti-C-N coated inserts is several times greater than the Ti-C-N coated ones. This is a result of the favourable thermophysical and tribological properties of Ti-N-C. The potential for tool protection by CrN coatings is a result of the high ductility and low internal stress of this coating materials. CrN films can be deposited with greater film thickness, still maintaining very good adhesion. This paper presents the development ...

Energy Technology Data Exchange (ETDEWEB)

A mathematical model of the multi machine electric power system to analyse its dynamics has been worked out. The effectivity of the power system stabilizer developed in the one machine system has been tested by means of this model. The influence of the arrangement of the stabilizers on the stability of the electric power system has also been investigated. High damping of electromechanical transient processes has been achieved. 7 refs., 1 tab., 5 figs.

Science.gov (United States)

An analysis of the diagnosis of loading and service dependability of a rail-mounted excavator used in surface lignite mining is described. Wheel power vibrations in electric motor bearings and electric motor input bearings to the gearbox were measured in situ, in horizontal, vertical, and axial directions. The data were analyzed using a mathematical relationship. The results are presented in a loading diagram that shows the deterioration and the acceptable lower bound of machine conditions over time. Work is continuing. 5 refs., 1 fig.

International Nuclear Information System (INIS)

For the lifetime evaluation of plasma facing materials in fusion experimental machines, it is essential to investigate their surface behavior and their temperature responses during an off-normal event such as the plasma disruptions. An infrared thermometer with a sampling speed as fast as 1x10"-"6 s/data, namely, the high-speed infrared thermometer (HSIR), has been developed by the National Research Laboratory of Metrology in Japan. To evaluate an applicability of the newly developed HSIR on the surface temperature measurement of plasma facing materials, high heat flux beam irradiation experiments have been performed with three different materials under the surface heat fluxes up to 170 MW/m"2 for 0.04 s in a hydrogen ion beam test facility at the Japan Atomic Energy Research Institute. As for the results, HSIR can be applicable for measuring the surface temperature responses of the armor tile materials with a little modification. It is also confirmed that surface ...

Energy Technology Data Exchange (ETDEWEB)

In order to achieve micro-wound, intelligence and high efficiency for fracture setting, intelligent setting system for fracture is proposed in accordance with biomechanics and fracture therapy theory. In the comprehensive medical system based on C-shape-arm X-machine, image processing and analysis is the core, programmable logical controller and stepping motor are important driving parts controlling mechanical parts. Six degree of freedom dynamics sensor ensures to control accurately force and moment. On the foundation of analyzing X-ray image peculiarities, method of processing and analysis is put forward, combining time domain with frequency domain. After mining domain knowledge in depth, setting actions is quantized into three non-continuous steps and is parameterized into two angles and one distance aiming at femoral-neck fracture. Objective features are extracted by virtue of three power polymerization curved surface fitting. Master-slave ...

International Nuclear Information System (INIS)

Development and deployment of small-scale nuclear power reactors and their maintenance, monitoring, and control are part of the mission under the Small Modular Reactor (SMR) program. The objectives of this NERI-consortium research project are to investigate, develop, and validate advanced methods for sensing, controlling, monitoring, diagnosis, and prognosis of these reactors, and to demonstrate the methods with application to one of the proposed integral pressurized water reactors (IPWR). For this project, the IPWR design by Westinghouse, the International Reactor Secure and Innovative (IRIS), has been used to demonstrate the techniques developed under this project. The research focuses on three topical areas with the following objectives. Objective 1 - Develop and apply simulation capabilities and sensitivity/uncertainty analysis methods to address sensor deployment analysis and small grid stability issues. Objective 2 - Develop and test an autonomous and fault-tolerant control ...

International Nuclear Information System (INIS)

Brachytherapy refers to short distance treatment of cancer with radiation from small, encapsulated radionuclide sources. This type of treatment is given by placing sources directly into or near the volume to be treated. The dose is then delivered continuously, either over a short period of time (temporary implants) or over the lifetime of the source to a complete decay (permanent implants). This technique is extensively used in the treatments of gynecological, breast, prostate, head and neck, and other soft tissue cancers. The clinical outcomes of this treatment depend on accurate dosimetry and dose delivery. The patient is generally considered to be water equivalent. So the treatment planning system software generally is based on measured or calculated dose distributions in homogenous water medium. In real situation, the treatment volume is not homogenous water medium, but it is a heterogeneous medium consisting of bone, soft tissue, lung, air etc. For better ...

International Nuclear Information System (INIS)

The MS Expert system provides problem diagnostics for instruments used in the Mass Spectrometry Laboratory (MSL). The most critical results generated on these mass spectrometers are the uranium concentration and isotopic content data used for process control and materials accountability at the Idaho General Processing Plant. The two purposes of the system are: (1) to minimize instrument downtime and thereby provide the best possible support to the Plant, and (2) to improve long-term data quality. This system combines the knowledge of several experts on mass spectrometry to provide a diagnostic tool, and can make these skills available on a more timely basis. It integrates code written in the Pascal language with a knowledge base entered into a commercial expert system shell. The user performs some preliminary status checks, and then selects from among several broad diagnostic categories. These initial steps provide input to the rule base. The ...

Energy Technology Data Exchange (ETDEWEB)

A prospective study was performed on 50 patients suffering from osteochondritis dissecans of the knee and ankle to define criteria for stability and fixation of osteochondral lesions. Morphological parameters in MRI (size, fragmentation, cartilage, interface) and conventional radiology (separation, fragmentation) were registered and compared with arthroscopical staging. MRI staging based on different types of interfaces was demonstrated on T{sub 1}- and T{sub 2}-weighted images. MRI could correctly predict a Grade 1 lesion in 50%, a Grade 2 lesion in 90%, a Grade 3 lesion on 0%, and a Grade 4 lesion in 79%. Stable lesions were differentiated from unstable lesions in 90%. Radiographic findings corresponded with arthroscopic staging in only 56% of the cases because fibrotic connection may guarantee stability in case of bony separation. (orig./MG) [Deutsch] In einer prospektiven Studie an 50 Patienten mit einer Osteochondrosis ...

Energy Technology Data Exchange (ETDEWEB)

Pd/sub 2/Si layers produced by evaporation or sputtering onto silicon substrates were examined by high resolution electron microscopy, microdiffraction, X-ray, energy loss and Auger spectroscopy. The Si-Pd/sub 2/Si interfaces produced by evaporation were in all cases rougher and more polycrystalline than those produced by sputtering. X-ray microanalysis showed the predictable variation in palladium distribution across the interface but quantification did not produce the expected palladium-to-silicon ratios, primarily because of probe broadening and X-ray-induced fluorescence. Energy loss spectra showed plasmon energy shifts and changes in Si L edge shape due to bond formation with palladium. Auger data provided evidence for a small amount of oxygen at the Si-Pd/sub 2/Si interface. Electrical measurements of the ideality factor for Schottky barriers made from the materials produced higher values for the rougher ...

Energy Technology Data Exchange (ETDEWEB)

We present the runtime comparison of the two versions of Super LU{_}DIST, using up to 128 processors of the IBM SP at NERSC. One version provides the global input interface, and another provides the distributed input interface. The comparison includes the total runtime of the solver with both 32-bit and 64-bit addressing modes, the time breakdown for different phases of the solver. We also present an in-depth comparison off our sparse matrix-vector multiplication methods in the context of iterative refinement. Finally, we describe our Fortran 90 interface that enhances the usability of the software.

Science.gov (United States)

A critical element of a retinal prosthesis is the stimulating electrode array, which is placed in close proximity to the retina. It is via this retinal-electrode interface that a retinal prosthesis electrically stimulates nerve cells to produce the perception of light. The impedance load seen by the current driver consists of the tissue resistance and the complex electrode impedance. The results in this paper show that the tissue resistance of the retina is significantly greater than that of the vitreous humor in the eye. Circuit models of the electrode-retina interface are used to parameterize the different contributors to the overall impedance. PMID:17325413

Energy Technology Data Exchange (ETDEWEB)

The Advanced Power Electronics Interfaces for Distributed Energy Workshop, sponsored by the California Energy Commission Public Interest Energy Research program and organized by the National Renewable Energy Laboratory, was held Aug. 24, 2006, in Sacramento, Calif. The workshop provided a forum for industry stakeholders to share their knowledge and experience about technologies, manufacturing approaches, markets, and issues in power electronics for a range of distributed energy resources. It focused on the development of advanced power electronic interfaces for distributed energy applications and included discussions of modular power electronics, component manufacturing, and power electronic applications.