Energy Technology Data Exchange (ETDEWEB)

Progress is reported in fabrication and coating activities being conducted for the weapons program, nuclear test program, nuclear design program, magnetic fusion program, and miscellaneous applications. (DLC)

International Nuclear Information System (INIS)

Surface quality is one of the most important criteria for establishing the optimum cutting parameters needed to perform a machining process. Usually, the evaluation of the degree of the surface finishing requires to apply metrological techniques which involve times out in the production. As a consequence of this, a loss in both the economy of the process and the fiability of the tests reproducibility can be produced. In this work a relation between cutting force and surface roughness has been studied for the turning process of an Al-Cu alloy. From this relation, the surface quality of the machined samples can be evaluated by using the cutting forces values acquired during the cutting process. (Author) 8 refs.

Energy Technology Data Exchange (ETDEWEB)

Hard surface finishing represents the final manufacturing step for functional areas of machine elements in state-of-the-art production. Raceways of rolling bearing rings are ground and honed to the required low roughness. Plastic deformation is restricted to a narrow edge zone of the hardened steel. Reheating of the machined components below the martensite tempering or bainite transformation temperature results in a marked decrease of the XRD line width on the surface. The investigated samples are made of through-hardened standard bearing steel 100Cr6 (international denotation: SAE 52100). On the basis of a material model that explains the effect as a complex diffusion process of dislocational carbon segregation, i.e. static strain aging, the measured kinetics of the XRD line width reduction is simulated by an Arrhenius-type equation, which describes the rate-controlling reaction step of temper carbide dissolution. The ...

Energy Technology Data Exchange (ETDEWEB)

Real-time horizon sensing on continuous mining machines is becoming an industry tool. Installation and testing of production-grade Horizon Sensor (HS) systems continued this quarter at Monterey Coal Company (ExxonMobil), Mountain Coal Company West Elk Mine (Arch), and Ohio Valley Coal Company (OVC). Monitoring of system function, user experience, and mining benefits is ongoing. All horizon sensor components have finished MSHA (U.S.) and IEC (International) certification.

Energy Technology Data Exchange (ETDEWEB)

Aluminum matrix composite Al356/SiCp(Vol. 15%)(Al MMC) material has been cut under various cutting conditions using Abrasive WaterJet (AWJ) machining process. The experimental cutting was carried out using three different material thicknesses of 10, 20, 30mm with a 0.33mm diameter orifice. The pump pressure, traverse rate, StandOff Distance(SOD) were taken as process parameters. After cutting the quality of the specimen in terms of kerf width, kerf taper, and surface finish were measured to characterize machinability of the material. As a result of the study, the maximum traverse rate for 30mm thick Al MMC under the pump pressure of 350 MPa reached up to 70 mm/min and the surface roughness of the material showed surface finish Ra in the range of 2.3{approx}23.4{mu}m.

Energy Technology Data Exchange (ETDEWEB)

A new rapid solidification process machine will be able to produce eight-inch diameter by six-inch thick finished cavities at the rate of one per hour - a rate that will change the tooling industry dramatically. Global Metal Technologies, Inc. (GMTI) (Solon, OH) has signed an exclusive license with Idaho National Engineered and Environmental Laboratories (INEEL) (Idaho Falls, ID) for the development and commercialization of the rapid solidification process (RSP tooling). The first production machine is scheduled for delivery in July 2001. The RSP tooling process is a method of producing production level tooling in prototype timing. The process' inventor, Kevin McHugh, describes it as a rapid solidification method, which differentiates it from the standard spray forming methods. RSP itself is relatively straightforward. Molten metal is sprayed against the ceramic pattern, replicating the pattern's contours, ...

Energy Technology Data Exchange (ETDEWEB)

A simple model based on surface chemistry is developed, based an simple concepts of contact angle, wetting and spreading. Results of the modeling can be stated by two simplified rules of thumb'': (1) A liquid will spread on the surface of a solid if the surface tension of the liquid is lose than the surface free energy of the solid, and (2) The liquid having the surface tension nearest that of the solid will preferentially wet the surface of the solid. These two rules can then be used to define the parameters that constitute a process for formulating a plastic bonded explosive (PBX), which is a crystalline high-explosive material coated with a small amount of plastic polymeric material (the binder). The PBX then can be pressed to a high density, and machined to a specific shape. The pressed and machined explosive material can then be used in a physics experiment to study fundamental properties of either ...

Energy Technology Data Exchange (ETDEWEB)

A billet of low-density carbon-bonded carbon fiber (CBCF) composite is machined into a desired attenuator or load element shape (usually tapering). The CBCF composite is used as a free-standing load element or, preferably, brazed to the copper, brass or aluminum components of coaxial transmission lines or microwave waveguides. A novel braze method was developed for the brazing step. The resulting attenuator and/or load devices are robust, relatively inexpensive, more easily fabricated, and have improved performance over conventional graded-coating loads.

Energy Technology Data Exchange (ETDEWEB)

A new thin film manufacturing method is established to add a function to glass material surface, as a new material technology which harmonizes with global environment, and is suitable for resource re-utilization and energy conservation. It is intended to develop a leading technology to promote recycling of colored glasses by applying this technical method to colored glasses. Fiscal 1998 has implemented subsequently to fiscal 1997 the following subjects in the three research items composed of a new manufacturing method of functional thin films, application of the functional thin films to colored glasses, and the comprehensive investigative studies: establishment of an industrial manufacturing method for color coating liquid and evaluation of basic characteristics of the colored functional thin films, optimization of element technology for photo-sensitive gel films by means of chemically modifying metallic alkoxide, tests of forming films on glass bottles and plate ...

Energy Technology Data Exchange (ETDEWEB)

The properties of AlN make this material very attractive for optical, electronic, and tribological application. Also, if the AlN could be formed on the Al surface to enhance its surface properties, Al could be applied for the lightening of machine parts. However, a dense oxide film exists on the surface of Al, which prevents the formation of the Al nitride even during plasma nitriding and plasma coating process. In this study, plasma nitriding has been tried to form an AlN layer on Al after the surface activation processes. During the plasma nitriding, the density of the nitrogen ions was amplified by means of controlling the power of the Al substrates. The film thickness, microstructural features and the mechanical properties such as hardness and wear properties of the AlN layer were examined as a function of the process parameters of pretreatment and plasma nitriding

Science.gov (United States)

... SCREENING GUN BARREL COATING'S RESPONSE ... SCREENING GUN BARREL COATINGS' RESPONSE TO COMBUSTION GASES ...

Science.gov (United States)

The implementation of a reverse time migration algorithm on the Connection Machine, a massively

International Science & Technology Center (ISTC)

New Composite Multifunctional Coatings Produced Using SHS-Electrodes

International Science & Technology Center (ISTC)

Development of the Method of Electrodepositing Nanostructured Composite Coatings with Improved Engineering Properties

Energy Technology Data Exchange (ETDEWEB)

A cryocondensation pump was designed for the baffle chamber of General Atomics DIII-D tokamak and will be installed in the fall of 1992. The purpose of the pump is to study plasma density control by pumping the divertor. The pump is toroidally continuous, approximately 10 m long and located in the lower outer corner of the vacuum chamber of the machine. It consists of a 1 m{sup 2} liquid helium-cooled surface surrounded by a liquid nitrogen-cooled shield to limit the heat load on the helium-cooled surface. The liquid nitrogen-cooled surface is surrounded by a radiation/particle shield to prevent energetic particles from impacting and releasing condensed water molecules. A thermal enhancement coating was applied to the nitrogen shell to lower the maximum temperature of the shell. The coating is non-continuous to keep the toroidal electrical resistance high. The whole pump is supported off the water-cooled vacuum vessel wall. ...

Energy Technology Data Exchange (ETDEWEB)

In this paper coating developments for advanced gas turbine engines (diffusion aluminide coatings, overlay coatings, and ceramic thermal barrier coatings) were desorbed, a selection of current metallic coatings was made and their performance as outlined. Finally coating developments for advanced diesel engines with a view to improved turbocharging or to low heat rejection engines (adiabatic diesel concept) were dealt with. (IHOE).

Energy Technology Data Exchange (ETDEWEB)

A processing technique for A-15 compounds which has improved mechanical and superconducting properties has been developed. This technique consists of rapid solidification of the alloy by the chill block spinning machine (CBSM) to form amorphous ribbons and by subsequent annealing crystallizes the stable or metastable fine grain flexible A-15 structure. The CBSM has been modified so that all the processing parameters could be controlled and optimized for each alloy composition. By the improved CBSM it was possible to form amorphous Nb{sub 3}Si, Nb{sub 3}Ge and Nb{sub 3}(AlSi) ribbons with more than 80% reproducible rate. Critical current density measurements are limited by contact resistance. A Cu plating technique was introduced in this research that made the contact resistance three orders of magnitude lower than that obtained by other methods. This plated coating also gave an additional mechanical support to the sample and acted as a shunt ...

Scientific Electronic Library Online (English)

Abstract in english We consider the three dimensional electromagnetic inverse scattering problem of determining information about a buried coated object from a knowledge of the electric and magnetic fields measured on the surface of the earth corresponding to time harmonic electric dipoles as incident fields. We assume that the buried object is a perfect conductor that is (possibly) partially coated by a thin dielectric layer. No a priori assumption is made on the extent of the coating, i.e. (more) the object can be fully coated, partially coated or not coated at all. We present an algorithm based on the linear sampling method and reciprocity gap functional for reconstructing the shape of the scattering obstacle together with an estimate of the surface impedance of the coating.

Energy Technology Data Exchange (ETDEWEB)

The fatigue properties of EP539LM alloy with an Al-Nb-Si fused slurry coating and a Co-Cr-Al-Y electron-beam coating are investigated experimentally in vacuum and in air at 900 C. It is found that the protective coatings reduce the fatigue life of the specimens both in vacuum and in air, with the electron-beam coating affecting the fatigue life of the alloy to a lesser degree than the fused slurry coating. The negative effect of the coatings on the fatigue life of the alloy is attributed largely to the properties of the coating material. 7 references.

International Nuclear Information System (INIS)

This Standards/Requirements Identification Document (S/RID) sets forth the Environmental Safety and Health (ESH) standards/requirements for the Plutonium Finishing Plant (PFP). This S/RID is applicable to the appropriate life cycle phases of design, construction, operation, and preparation for decommissioning. These standards/requirements are adequate to ensure the protection of the health and safety of workers, the public, and the environment.

Energy Technology Data Exchange (ETDEWEB)

In vitro cytocompatibility and cellular interactions of lauric acid and dextran-coated magnetite nanoparticles were evaluated with two different cell lines (mouse fibroblast and human cervical carcinoma). Lauric acid-coated magnetite nanoparticles were less cytocompatible than dextran-coated magnetite nanoparticles and cellular uptake of lauric acid-coated magnetic nanoparticles was more than that of dextran-coated magnetite nanoparticles. Lesser cytocompatibility and higher uptake of lauric acid-coated magnetite nanoparticles as compared to dextran-coated magnetic nanoparticles may be due to different cellular interactions by coating material. Thus, coating plays an important role in modulation of biocompatibility and cellular interaction of magnetic nanoparticles.

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

International Nuclear Information System (INIS)

... brakes reactor charging machines reactors machine parts Int. Cl. B66d5/00;

Energy Technology Data Exchange (ETDEWEB)

MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing ...

Energy Technology Data Exchange (ETDEWEB)

PVD-chromium-nitride coated samples of substrates of the magnesium alloy AZ91hp and the roller and ball bearing steel 100Cr6 were investigated regarding structure, mechanical characteristics, adhesion and internal stresses. For the coatings the parameters layer thickness and substrate BIAS voltage were varied. Both substrate materials were coated in one lad. Results of the X-ray analysis of the internal stresses show significant differences between the coated magnesium and the coated steel substrates. In the case of the variation of the substrate BIAS voltage, for the coated steel a dependency of the internal stresses to coating parameters could be obtained. For the coated magnesium no dependency was recognizable. The coating structure was examined with scanning electron microscopy. Element depth ...

Energy Technology Data Exchange (ETDEWEB)

Standard Leadframes used in surface mount technology are finished with a layer of eutectic SnPb for passivation and for enhancing solder wetting during reflow. When eutectic SnPb is replaced by Pb-free solder, especially the eutectic SnCu, a large number of Sn whiskers are found on the Pb-free finish. Some of the whiskers are long enough to become shorts between the neighboring legs of the leadframe. How to suppress their growth and how to perform accelerated test of Sn whisker growth are crucial reliability issues in the electronic packaging industry. In this paper, we report the study of spontaneous Sn whisker growth at room temperature on eutectic SnCu and pure Sn finishes. Both compressive stress and surface oxide on Sn are necessary conditions for whisker growth. Structure and stress analyses by using the micro-diffraction in synchrotron radiation are reported. Cross-sectional electron microscopy, with samples prepared ...

UK PubMed Central (United Kingdom)

Enzootic Glassers's disease was investigated to study the epidemiology of the disease strains on a farm where it presented a problem. Restriction endonuclease fingerprinting (REF) analysis technique...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A review of chemical decontamination methods for coatings indicates the following: the ease of both contamination and decontamination is a function of the radionuclide and the pH of the environment; the coating type is important in determining whether the contamination is loosely adsorbed, complexed, or contained in porous filler material; the condition of the coating is important to the decontamination factor obtained. Thus coatings can be decontaminated provided the solvent is sufficiently acid to solubilize the radionuclide and the complexant strength of the solvent is greater than that of the coating. Difficulties arise if the contamination is associated with fillers. Furthermore, though nothing has been said about temperature, decontamination of metal goes faster and, usually, with better efficiency at high temperatures. 11 references, 3 figures.

Science.gov (United States)

For abstract, see NSA 27 06, number 14465.

Science.gov (United States)

Cardiac Arrest; Cardiopulmonary Resuscitation

British Library Electronic Table of Contents (United Kingdom)

The purpose of this study is to investigate the influence of tungsten carbide/carbon (WC/C) coating on the surface durability of casehardened steel gear. Two kinds of WC/C coatings were deposited on the ground gear pair made of chromium molybdenum steel with carburizing and quenching. One is the conventional WC/C coating, and the other is WC/C coating with about 1 ?m CrN interlayer. Here, the WC/C-coated test pinion and the WC/C-coated one with CrN interlayer are represented by WT and ST, respectively. Non-coated test pinion is represented by NT. The surface roughness along the tooth profile direction of WT and ST was almost the same as that of NT. A spur gear test was carried out with an IAE power circulating type gear test rig under EP gear oil lubricating condition. The fatal failure mo...

Science.gov (United States)

... Accession Number : ADA544419. Title : Omental Lipid-Coated Mesh. Descriptive Note : Final rept. 1 Jul 2009-16 Jun 2011. ...

British Library Electronic Table of Contents (United Kingdom)

Ceramic coatings with high emission were fabricated on Ti6Al4V alloy by microarc oxidation (MAO) with additive FeSO4 into the electrolyte. The microstructure, chemical composition and chemical state of the coatings were determined by SEM, XRD, EDS and XPS, respectively. The bonding strength between the coating and substrate was studied by tensile strength test, together with the thermal shock resistance of the coating. The results showed that Fe content in the coating layer significantly affect its thermal emissivity. The relative content of Fe in the coatings surface increased at first and then decreased with increasing the concentration of FeSO4 in electrolytes, so does the emissivity of the coatings. The bonding strength became weaker with increasing the concentration of FeSO4. In addit...

International Science & Technology Center (ISTC)

Hard Nano-Strutural Coatings Resistant to the Extreme Conditions of Chemical, Abrasive and High Energy Media for Thermonuclear Power, Oil and Gas and Chemical Industries

Science.gov (United States)

... Accession Number : ADA954164. Title : Electron Diffraction Examination of Gun Barrel Coatings. Descriptive Note : Special rept.,. ...

Energy Technology Data Exchange (ETDEWEB)

A virtual balancing axis arrangement is described for multi-cylinder reciprocating piston machines for effectively balancing out imbalanced forces and minimizing residual imbalance moments acting on the crankshaft of such machines without requiring the use of additional parallel-arrayed balancing shafts or complex and expensive gear arrangements. The novel virtual balancing axis arrangement is capable of being designed into multi-cylinder reciprocating piston and crankshaft machines for substantially reducing vibrations induced during operation of such machines with only minimal number of additional component parts. Some of the required component parts may be available from parts already required for operation of auxiliary equipment, such as oil and water pumps used in certain types of reciprocating piston and crankshaft machine so that by appropriate location and dimensioning in ...

Science.gov (United States)

The strength, stiffness, and range of single-stranded stainless steel (SS) and superelastic nickel-titanium (NiTi) archwires were compared with those of alternative leveling products, including nylon-coated and multistranded wires. Wire cross-sections were photographed after being potted in polymer, ground, and polished. Because the rectangular wires had rounded or beveled corners, gravimetric measurements and specific gravity calculations quantified the actual polygonal cross-sectional areas versus the ideal rectangular cross-sectional areas. Beveling reduced the cross-sectional areas by 7% to 8%; this decreased the wire stiffnesses by 15% to 19%. Using a testing machine, we measured the yield strengths, the elastic limits, and the ultimate tensile strengths in tension, and wire stiffnesses in 3-point bending. From cyclic loading tests, the elastic limits of the superelastic NiTi wires were approximately 90% and 45% of their ultimate tensile ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a feasibility demonstration of a thermal scanning NDE system for thermal spray coatings. Non-bonds were detected between several types of coatings and their substrates. Aluminum anti-skid coatings having very rough surfaces were included. A technique for producing known non-bond areas for calibrating and demonstrating NDE methods was developed.

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning the structural properties of sputtered tantalum and tantalum compounds. The preparation of thin film capacitors and resistors is described. The electrical properties of the sputtered films are also included. The influence of the substrate on the properties of the coatings is considered, including adherence of the coating to the substrate, and the effects of impurities on coating integrity. (Contains 250 citations and includes a subject term index and title list.)

Energy Technology Data Exchange (ETDEWEB)

Non-destructive methods for measuring the remaining anticorrosive or antioxidative ability of coatings are investigated. For anticorrosive chromium coatings the increasing ferromagnetism caused by loss of chromium is measured by a permeability probe. Measured values on blades after operation are correlated with the progress of corrosion as determined by metallographic methods. For antioxidative aluminum coatings the diminishing layer thickness is taken as indication for the exhaustion of their protection ability. The layer thickness is measured eddy current probes, especially developed for this application.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The structure and properties of composite powder coatings on the base of titanium carbide are studied. It is shown the electron-beam welding deposition of powders on the base of nickel and titanium carbide allows to produce of high-quality wear-resistant coatings which superior in density and hardness compared with sputtered ones. Changes of hardening phase volume percentage as well as composition of metal matrix make possible to control coatings hardness

Energy Technology Data Exchange (ETDEWEB)

Simulated atmospheric corrosion studies were performed to determine the corrosion protection provided by galvanized zinc coatings on depleted uranium, U-0.75 Ti alloy, and U-6 Nb alloys. The accelerated ASTM tests consisted of exposing the galvanized samples to aqueous and aqueous chloride environments. The test results showed that anodic protection was provided by the electronegative zinc coatings on uranium and uranium alloys. Treating zinc with chromate conversion coatings also provided more protection.

British Library Electronic Table of Contents (United Kingdom)

The effect of heat treatment on the corrosion behavior of reactive plasma sprayed TiN coatings in simulated seawater was investigated by electrochemical methods such as the corrosion potential-time curve (Ecorr-t), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and SEM, etc. The results showed that the corrosion potential of TiN coatings increased after heat treatment; the corrosion current of the TiN coatings after heat treatment (be hereafter referred to as HT-TiN) was 13.3% of the untreated coatings (be hereafter referred to as UT-TiN), and the polarization resistance of HT-TiN was 20 times of UT-TiN, which indicated that the heat treatment had significantly increased the corrosion resistance of the coatings. The corrosion behavior of the coatings was mainly ...

Energy Technology Data Exchange (ETDEWEB)

There is an increasing number of applications for hard coatings in engineering where the properties of the single-layer coating are not sufficient. One way to solve this problem is to use a multilayer coating that combines the properties of several coating materials. In this study, TiN-CrAlN and CrN-CrAlN multilayer coatings were deposited on 100Cr6 and S6-5-2 (DIN) steel substrates, by means of unbalanced magnetron sputtering. For comparison, TiN, CrN and CrAlN single-layer coatings were also prepared. For all depositions the coating temperature was below 473 K. Indentation testing, hardness measurements and scratch tests were performed to characterize the mechanical properties. The correlation between the wear behavior in rolling contact and the mechanical properties of the multilayer coatings is reported. A ball ...

Energy Technology Data Exchange (ETDEWEB)

From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and Zn content in the ...

British Library Electronic Table of Contents (United Kingdom)

Machine-to-machine (M2M) communications is a new and rapidly developing technology for large-scale networking of devices without dependence on human interaction. Energy efficiency is one of the important design objectives for machine-to-machine network architectures that often contain multi-hop wireless subnetworks. Constructing energy-efficient routes for sending data through such networks is important not only for the longevity of the nodes which typically depend on battery energy, but also for achieving an environmentally friendly system design overall, which will be imperative as M2M networks scale in number of nodes as projected. The objective of this survey is to provide a comprehensive look into shortest-path based energy-efficient routing alternatives to provide a reference for sys...

CERN Document Server

Proposal for the award of a contract, without competitive tendering, for the replacement of lift machine room equipment and the installation of remote monitoring systems

International Nuclear Information System (INIS)

Hybrid organic-inorganic coatings with phosphonate functionalities have been synthesized and evaluated as prospective surface treatments for magnesium materials. These coatings have been processed via a sol-gel route by hydrolysis and condensation of a mixture of diethylphosphonatoethyltriethoxy-silane and tetraethoxy-silane with variable molar ratios. The coatings morphology and the surface chemistry at the coating/substrate interface have been characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, "3"1P nuclear magnetic resonance spectroscopy, and time-of-flight secondary ion mass spectrometry. The corrosion protection performance of the coatings deposited on magnesium alloy AZ31B has been examined by a group of electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, a scanning Kelvin ...

Energy Technology Data Exchange (ETDEWEB)

In the framework of the European Fusion Technology Programme ECN participates in a NET task PSM-8 `Coatings and Surface Effects on Stainless Steel 316L`. High emissivity coatings were developed for enhanced heat transfer from graphite tiles to a Stainless Steel First Wall. Four candidate materials, Cr{sub 2}O{sub 3}, Black Cr, Al{sub 2}O{sub 3}/TiO{sub 2} and TiC were tested as candidate high emissivity coatings. These coatings were manufactured by atmospheric and vacuum plasma spraying technique and the Black Chromium coatings were manufactured by a galvanic coating technique. The tests included total emissivity measurements and Low Cycle Fatigue (LCF) experiments. The total emissivity of two TiC coatings at 525 K appeared to be 0.62 and 0.64. The total emissivity of the TiC and 5 wt% TiO{sub 2}/Al{sub 2}O{sub 3} ...

Energy Technology Data Exchange (ETDEWEB)

An International Workshop on Metrology for X-ray and Neutron Optics has been held March 16-17, 2000, at the Advanced Photon Source, Argonne National Laboratory, near Chicago, Illinois (USA). The workshop gathered engineers and scientists from both the U.S. and around the world to evaluate metrology instrumentation and methods used to characterize surface figure and finish for long grazing incidence optics used in beamlines at synchrotrons radiation sources. This two-day workshop was motivated by the rapid evolution in the performance of x-ray and neutron sources along with requirements in optics figure and finish. More specifically, the performance of future light sources, such as free-electron laser (FEL)-based x-ray sources, is being pushed to new limits in term of both brilliance and coherence. As a consequence, tolerances on surface figure and finish of the next generation of optics are expected to become tighter. The ...

Energy Technology Data Exchange (ETDEWEB)

In the last two years, the VDMA work group 'Functional security' compiled a qualitative and quantitative procedure for the determination and evaluation of turbo-machine specific risks. With the calibrated risk graph for turbo-machines the requirements (Safety Integrity Level SIL) to the protective functions for turbo-machines (steam turbines, gas turbines, generators and compressors) were determined. With consideration of the legislation, the work group compiled a recommendation for the renewal and/or reconstruction of protective functions with old facilities.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Accession Number : ADA079641. Title : Relation of the One-Phase Stefan Problem to the Seepage of Liquids and Electrochemical Machining,. ...

British Library Electronic Table of Contents (United Kingdom)

China's propaganda machine seeks to control public opinion at all costs?-?and the media is its tool, writes David Bandurski

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under the session headings: research in mechanical fragmentation; rock characterization, remote sensing and interface detection; monitoring, data transmission and communications; tunnel boring machines; minewide monitoring and expert systems for ground control; machine guidance; shaft and raise boring; automation of drilling equipment; machine automation and control; new developments in mechanical miners; materials handling; innovative mining systems; general minewide monitoring and expert systems; ground support; human factors; and extraterrestrial mining.

Energy Technology Data Exchange (ETDEWEB)

Processes were developed that use lasers as manufacturing tools. These processes were stripping of insulation from cables and wires, machining of quartz, microdrilling and welding of reflective metals, and precision alignment of curved surfaces before machining. A technological basis also was formed which resulted in a process for automatic surface inspection of parts and aided development of machining processes for Kevlar parts.

International Nuclear Information System (INIS)

In this paper, the influence of plasma nitriding at temperature 720 deg. C for 20 h on the surface microstructure and interface microstructure of electroplated chromium coating was investigated. In these conditions, interdiffusion, mixing and reaction phenomena of elements originating from the substrate and coating material are more likely to occur, thus increasing the bonding strength between the coating and carbon steel substrate. The change of the structures from the substrate side to the coating surface, and the effect of the substrate steel on the interface structure were studied by cross-sectional transmission electron microscope observation (XTEM). The nitride layer formed on the surface was analyzed by X-ray diffraction method (XRD). After treatment at above conditions a 6-7 #mu#m thick nitride compound layer was formed in surface region and the same thick carbide compound layer was also formed ...

British Library Electronic Table of Contents (United Kingdom)

In situ composite coating of hydroxyapatite (HA)/TiO2 were produced on titanium (Ti) substrate by micro-arc oxidation coupled with electrophoretic deposition (MAO&EPD) technique with different concentrations of HA particles in the 0.2M NaOH electrolyte solution. The surface morphology and chemical composition of the hybrid coating were effected by HA concentration. The amount of HA particles incorporated into coating layer increased with increasing HA concentration used in the electrolyte solution. The corrosion behavior of the coating layer in simulated body fluids (SBF) was evaluated using a potentiodynamic polarization test. The corrosion resistance of the coated sample was increased compared to the untreated Ti sample. The in vitro bioactivity assessment showed that the MAO&EPD treated...

British Library Electronic Table of Contents (United Kingdom)

Assembly of icosahedral capsids of proper size and symmetry is not understood. Residue F170 in bacteriophage P22 coat protein is critical for conformational switching during assembly. Substitutions at this site cause assembly of tubes of hexamerically arranged coat protein. Intragenic suppressors of the ts phenotype of F170A and F170K coat protein mutants were isolated. Suppressors were repeatedly found in the coat protein telokin-like domain at position 285, which caused coat protein to assemble into petite procapsids and capsids. Petite capsid assembly strongly correlated to the side chain volume of the substituted amino acid. We hypothesize that larger side chains at position 285 torque the telokin-like domain, changing flexibility of the subunit and intercapsomer contacts. Thus, a sing...

Energy Technology Data Exchange (ETDEWEB)

A method for preparing metal for heating by infrared radiance to enable uniform and consistent heating. The surface of one or more metal parts, such as aluminum or aluminum alloy parts, is treated to alter the surface finish to affect the reflectivity of the surface. The surface reflectivity is evaluated, such as by taking measurements at one or more points on the surface, to determine if a desired reflectivity has been achieved. The treating and measuring are performed until the measuring indicates that the desired reflectivity has been achieved. Once the treating has altered the surface finish to achieve the desired reflectivity, the metal part may then be exposed to infrared radiance to heat the metal part to a desired temperature, and that heating will be substantially consistent throughout by virtue of the desired reflectivity.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this investigation was to simulate a machining front from an abrasive waterjet and its movements in a ceramic material. Wear factors affecting the abrasive waterjet nozzle were also to be established. Therefore, a low inclination angle (9[degree]) was used between the nozzle and test sample, simulating a moving machine front. A standard nozzle with an inner diameter of 0.76 mm was used in the test, and it was placed close to the samples. The outer diameter of the abrasive nozzle was 9.5 mm. The high wear rate from abrasive waterjets makes it possible to machine hard ceramics-including dense alumina, titanium boride, silicon nitride, and composites-at high machining speeds.

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to investigate the applicability of a combined Global Positioning System and Inertial Measurement Unit (GPS/IMU) for information based displays on earthmoving machines and for automated earthmoving machines in the future. This technology has the potential of allowing an information-based product like Caterpillar's Computer Aided Earthmoving System (CAES) to operate in areas with satellite shading. Satellite shading is an issue in open pit mining because machines are routinely required to operate close to high walls, which reduces significantly the amount of the visible sky to the GPS antenna mounted on the machine. An inertial measurement unit is a product, which provides data for the calculation of position based on sensing accelerations and rotation rates of the machine's rigid body. When this information is coupled with GPS it ...

International Nuclear Information System (INIS)

Several metallurgical coatings have been developed that provide good tribological performances in high-temperature liquid sodium and that are relatively unaffected by neutron fluences to 6 X 10/sup 22/ n/cm/sup 2/ (E > 0.1 MeV). The coatings that have consistently provided the best tribological performance have been the nickel aluminide diffusion coatings created by the pack cementation process, chromium carbide or Tribaloy 700 trade mark (a nickel-base hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing alloy) applied by the detonation-gun process, and chromium carbide and other hardfacing materials applied by the electro-spark deposition process. The latter process is a relatively recent development for nuclear applications and is expected to find wide usage. Other coating processes, such as plasma-spray coating, sputtering, and ...

Energy Technology Data Exchange (ETDEWEB)

Duplex-coating procedures consisting of plasma nitriding and Me-C:H hard coating lead to an improved performance of the devices because the Me-C:H coating is supported by the nitrided phase and, therefore, the `eggshell-effect` is avoided. Furthermore, this support leads to a higher load-bearing capacity of the thin film. Two standard procedures (classical high-pressure plasma nitriding and unbalanced magnetron sputtering of Ti-C:H) were performed subsequently to prepare the duplex coatings on X20Cr13 ferritic stainless steel. The corrosion resistance of the steel could be improved by nitriding at 450 C compared to the untreated ferritic substrate. The roughness is determined by the nitriding step. The weakest point of the coating is the transition zone between the nitrided and the untreated substrate and not the interface between the Ti-C:H coating and the ...

International Nuclear Information System (INIS)

The industrial radiation processing using low energy electron beam (EB) accelerators lower than 300 keV offers high speed, safe technologies for the chemical conversion of thin layer coatings. Because of the nonselective mode of initiating chain reaction polymerization involving free radicals in synthetic coating layers and suitable substrates, the EB curing of the coatings on woods and papers has particular advantage. Hungary decided to start an up-to-date EB line to process cement-bound (CB) wood chipboards with pigmented acrylic coatings. The CB wood chipboards contain more than 60 % of portland cement and up to 40 % of wood particles. They are produced as large boads of 6 - 16 mm thickness. In their fireproof character and other aspects, they are similar to asbestos-cement boards without containing carcinagenic asbestos, and are stable against moisture and atmospheric influences. EB-cured acrylate ...

UK PubMed Central (United Kingdom)

Computer-assisted analysis revealed a striking sequence similarity between the putative 24-kDa protein (p24) encoded by open reading frame (ORF) 5 of beet yellows closterovirus and the coat protein...Full Text Available

International Nuclear Information System (INIS)

A report is given on an improved filler-binder mixing method in the manufacture of artificial graphite, the so-called coat-mix process. The individual graphite-filler grains are coated completely with uniform binder coatings (phenol formaldehyde resin) in a continuous process. Methanol is used as solvent for the resin. In a modified further development of the process, the use of organic solvents can be disregarded by dissolving the binder resin in caustic soda and injecting the slurry into water diluted acid. The manufacture of casting molds from coat-mix powders, their properties and industrial application are given. Finally, the advantages of using carbon bodies of coal-mix material for conversion to silicon carbide are indicated. (IHOE).

Energy Technology Data Exchange (ETDEWEB)

The refractory nature and high ductility of body centered cubic (bcc) phase tantalum makes it a suitable material for corrosion- and wear-resistant coatings on surfaces that are subjected to high stresses and harsh chemical and erosive environments. Sputter deposition can produce thick tantalum films but is prone to forming the brittle tetragonal beta phase of this material. Efforts aimed at forming thick bcc phase tantalum coatings in both flat plate and cylindrical geometries by high-rate triode sputtering methods are discussed. In addition to substrate temperature, the bcc-to-beta phase ratio in sputtered tantalum coatings is shown to be sensitive to other substrate surface effects.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This book describes the uses, coatings, and fabrication of laser materials. Topics considered include: optical waveguide materials; optical storage materials; holographic recording materials; phase conjunction materials; holographic recording materials; phase conjunction materials; laser crystals; laser glasses; quantum counter materials; thin films and coatings; multilayer dielectric coatings; graded-index surfaces and films; optical materials fabrication; fabrication techniques; fabrication procedures for specific materials.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

Energy Technology Data Exchange (ETDEWEB)

One requirement of a thermophotovoltaic (TPV) radiator is to efficiently emit photons at high temperatures to TPV cells for conversion to electric power. Because many candidate radiator materials with adequate structural properties display low emissivity, coatings or other surface modifications are required for enhancement of emissivity. Six plasma sprayed coatings and one textured surface demonstrated adequate thermal stability and emittance values of 0.8 or greater. Promising attributes of modified surfaces are identified.

Energy Technology Data Exchange (ETDEWEB)

The method of production of xAl{sub 2}O{sub 3}-yTiO{sub 2} compositions provides for the depth distribution of coating components and specifies its mechanical properties. In case of the composition obtained by cladding, titanium is mainly concentrated at the substrate. In case of mechanical mixture or composition obtained by sintering the oxides, the depth distribution of coating components is random.

Energy Technology Data Exchange (ETDEWEB)

The method of the present invention comprises a step of previously coating a positive type resist on the surface of equipment, a step of solidifying the coated positive type resist and a step of bringing the coated equipment to circumstances for use and cleaning the positive type resist. With such procedures, the amount of radioactive materials deposited on the equipment can be reduced, and redeposition of nuclides on the surface to be cleaned can be prevented. (T.M.)

Energy Technology Data Exchange (ETDEWEB)

A review of theoretical and observational research on the magnetopause during 1987-1990. Starting with recent work on magnetic reconnection, the review proceeds to magnetopause surface wave phenomena, including the controversy over the role of solar wind pressure pulses in the coupling process and in the mimicking of flux transfer events signatures, and finishes with the magnetopause structure and associated wave phenomena. Recent advances in computer modeling of the magnetopause and the pertinent processes are also discussed. 108 refs.

Energy Technology Data Exchange (ETDEWEB)

Reports by U.S. workers on geodetic measurements of recent plate motions or crustal deformation published in 1987-1990 are reviewed. The review begins with global plate motions, proceeds through plate boundaries in California, Alaska, and the Pacific Northwest, and finishes with volcanic phenomena, monument stability and longevity, and GPS relative position measurements. 184 refs.

Energy Technology Data Exchange (ETDEWEB)

All the tests have been finished up in the Waste Management and Disposal Facility which has been used for the safety tests of solidified radioactive waste on sea dumping disposal. The decommissioning of this facility was performed for use of radioisotopes. This report describes the plan on decommissioning of facility for use of radioisotopes, the contamination checking methods and measurement of radioactivity, the fore case and practice for amount of generated radioactive wastes, the operation procedures for dismantlement, the safety measures, the expenses for decommissioning and so on. (author)

International Nuclear Information System (INIS)

In co-operation with the Scientific Planning Department of the Central Research Institute for Vessel- and Turbine Building the construction office of the turbine factory Charkow finished the draft of a slowly running (n = 1500 min"-"1) 2 GW-turboset for the operation of nuclear power plants. The chief purpose of the project was to determine the technical problems that are used to occur during the development of such steam turbines, as well as to settle the most favourable design. (orig./GL).

International Nuclear Information System (INIS)

Research highlights: ? Reports a high protection system for the alloy in corrosive environment. ? Describes an interfacial process with self-healing properties. ? Reports the influence of substrate pre-treatment in the coating performance. - Abstract: In this paper the interface of poly(vinylidene fluoride) coatings prepared by the dip coating method and HF-treated AZ31 magnesium alloy was evaluated. The best performance of this system in corrosion tests compared to ground, as-received and acetic acid cleaned substrates is related to an acid-base interaction at the interface and to interfacial reactions which resulted in a self-healing process. The protectiveness of the samples was investigated using impedance and immersion tests while the coating morphology and interface stability were investigated by scanning electron microscopy, X-ray photoelectron spectroscopy and adhesion tests.

Energy Technology Data Exchange (ETDEWEB)

The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise fashion by changing the ...

British Library Electronic Table of Contents (United Kingdom)

Analysis reproducibility and detection sensitivity of capillary electrophoresis (CE) are often questioned by applied scientists, which has hindered its application as a routine method. To address these issues, a simple, precise, and reproducible dynamic coating method was developed by applying carboxymethyl chitosan (CMC) dynamic coating on fused silica capillary. The proposed coating was accomplished by simply rinsing the capillary with CMC solution for 1?min in between runs, with no regeneration procedure or buffer additives needed. Electroosmotic flow could be well controlled by adjusting the pH of background electrolyte, and the adsorption of analytes onto the capillary inner wall was effectively eliminated. The main parameters of the coating condition were optimized, and extensive app...

Energy Technology Data Exchange (ETDEWEB)

Ion storage CeO{sub 2} and CeO{sub 2}/SnO{sub 2} coatings were prepared by sol-gel dip-coating method using aqueous-based process. The influence of added SnO{sub 2} in the CeO{sub 2} oxide coatings on the inserted/extracted charge was determined by chronocoulometric measurements. It was found that for 60 nm thick film the inserted/extracted charge was twice larger (Q = 10mC/cm{sup 2}) for films containing 17 mol % SnO{sub 2} if compared to pure CeO{sub 2}. The addition of SnO{sub 2} to the mixed oxides coatings on their optical properties and structural characteristics were studied.

British Library Electronic Table of Contents (United Kingdom)

The determination of residual stress (RS) in case-hardened steel gear truck synchronisers coated with thermal sprayed molybdenum was carried out using neutron and synchrotron X-ray diffraction. Two samples with different coating thicknesses (about 120 ?m and 1.4 mm) and different steel substrates (16MnCr5 and SAE4140, respectively) were investigated. Microanalysis revealed substantial porosity in both samples and some debonding was observed between the thin coating and the substrate. The bulk hardness of the SAE 4140 proved to be much higher than the 16MnCr5 and the surface case-hardening increased it by a further 20%. The full three-dimensional stress depth-profile was determined by neutron diffraction (ND) in both the coatings and the substrates, while synchrotron radiation allowed a dep...

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction.- Infection is the worst complication seen with inflatable penile prosthesis (IPP). Both the American Medical Systems (AMS) and Coloplast IPP have infection retardant coatings. AMS is coated at the factory with rifampicin and minocycline (InhibiZone). The Coloplast IPP has a hydrophilic coating covalently bonded to its components that will absorb any aqueous solution before implantation and provides increased surface lubricity to decrease bacterial adherence. Aim.- We tested several antibiotic dips comparing zones of inhibition (ZOI) against five commonly infecting bacteria with coated Coloplast implants. Results were compared with those ZOI created with strips of an AMS IPP precoated with InhibiZone. Methods.- Pieces of sterile Coloplast Titan IPP were dipped in (i) ...

British Library Electronic Table of Contents (United Kingdom)

The combined processes of plasma nitriding and cathodic arc deposition of (Ti,Cr,Nb)CN coatings were applied to HSS substrates. The nitrided layers, obtained in a mixture of H2 (70%) and N2 (30%) at two different temperatures (480^oC and 510^oC), were examined for the microhardness depth profiles. Characterization of the duplex coatings was performed by investigating elemental and phase composition, texture, hardness, friction and wear. XRD and XPS analyses revealed the formation of a mixture of a carbonitride fcc solid solution, in a dominant proportion, and metallic chromium. The film hardness was measured to be ~34GPa. The duplex (Ti,Cr,Nb)CN coatings exhibited superior tribological behavior as compared to both nitrided layers and non-duplex coatings.

Science.gov (United States)

A focused ion beam (FIB) technique was applied to cross-sectional specimen preparation to observe an interface between a plasma sprayed coating and an aluminum (Al) substrate by transmission electron microscopy (TEM). The surface of the sprayed coating film has a roughness of several tens of microns. Sputter rates for the coating film and the substrate are greatly different. The rough surface and the difference in sputter rate cause problems in making TEM specimens with smooth side walls. The top surface of the coating film was planerized by the FIB before fabricating the TEM specimen. The interfaces were investigated by TEM and energy-dispersive X-ray (EDX) analysis. The TEM observation revealed that there is a 10 nm thick amorphous layer at the interface between the coating film and substrate. The coating film consists of two kinds of sublayers with bright and ...

Energy Technology Data Exchange (ETDEWEB)

Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.

International Nuclear Information System (INIS)

Gallium liquid-metal ion sources that have been introduced in the late 1970s have allowed the development of a new class of micro- and nanofabrication tools collectively denominated as focused ion beam (FIB) machines. To investigate the potential of a helium beam in such a FIB instrument the authors have tested a room-temperature electron beam ion trap coupled with a high resolution FIB machine. In this letter they present their first results in target imaging using a helium beam with a resolution that allows to account for a beam diameter in the submicrometer range.

Energy Technology Data Exchange (ETDEWEB)

A gelcasting composition has improved drying behavior, machinability and shelf life in the dried and unfired state. The composition includes an inorganic powder, solvent, monomer system soluble in the solvent, an initiator system for polymerizing the monomer system, and a plasticizer soluble in the solvent. Dispersants and other processing aides to control slurry properties can be added. The plasticizer imparts an ability to dry thick section parts, to store samples in the dried state without cracking under conditions of varying relative humidity, and to machine dry gelcast parts without cracking or chipping. A method of making gelcast parts is also disclosed.

Science.gov (United States)

we have a colloquium scheduled. Computing: register your machine and check our network security and visitor computer policies. For Our Information: Once arranged, please let us...

Science.gov (United States)

verified Java program is executed by JPF, which is a virtual machine ..... only subset of Java instructions can have inter-thread effects ...

Science.gov (United States)

... non- emissive guidance and collision alert, automated transport in dynamic environments, and assembly and inspection. Foveal Vision, Autonomous Agents, ...

Energy Technology Data Exchange (ETDEWEB)

In this project, graphite is used as a substitute for lead in order to maintain the machinability of plumbing components at the level of leaded brass. Graphite dispersed in Cu alloy was observed to impart good machinability and reduce the sizes of chips during machining of plumbing components in a manner similar to lead. Copper alloys containing dispersed graphite particles could be successfully cast in several plumbing fixtures which exhibited acceptable corrosion rate, solderability, platability, and pressure tightness. The power consumption for machining of composites was also lower than that of the matrix alloy. In addition, centrifugally cast copper alloy cylinders containing graphite particles were successfully made. These cylinders can therefore be used for bearing applications, as substitutes for lead-containing copper alloys. The results indicate that copper graphite alloys developed under this ...

CERN Document Server

"Machines of all kinds depend on complex software to keep them operating safely. But how reliable is the software - and how can we be sure it is reliable?" (4 pages)

Science.gov (United States)

TRACON controller, traffic flow manager, or pilot. .... separation violations to individual controller and ..... System, AGARD Meeting on Machine Intelligence ...

Energy Technology Data Exchange (ETDEWEB)

There is presently considerable interest in wear resistant coatings produced using closed field unbalanced magnetron sputtering technology. For example, layered films of diamond-like carbon (DLC) with tungsten or titanium additions have been widely reported. The benefit is that the mechanical properties are enhanced (e.g. giving greater toughness); also it is possible to control the stress state and enhance adhesion. Here we report the further development of this concept by the addition of TiN, TiCN and TiC layers in DLC-based composites, utilizing an additional source of electrons in the vicinity of substrate to enhance ionisation of the plasma and increase coating density. Composite coatings of ceramics TiN, TiC{sub x}N{sub y}, TiC, CrN, TiCrN, TiCrCN, TiCrC, metal doped Ti{sub x%}-DLC and their combinations were deposited on 316 stainless steel substrates. The mass flow of reactive gases into the chamber was controlled ...

International Nuclear Information System (INIS)

Research highlights: The dental implant of titanium could be modified by anodic oxidation. It was found that incorporation of strontium ions into the matrix increase the bone formation. In this study, we try to investigate the effect of corrosion property and bioactivity on coatings containing strontium by anodic oxidation. The results suggest that coatings containing strontium on titanium by anodic oxidation has the potential to show the stability and bioactivity in the clinical use. - Abstract: Pure titanium (Ti) and titanium alloys are considered as bio-inert materials in clinical use. Bioactivity is the ability to induce bone-like apatite on the material surface. The micro-arc oxidation (MAO) technique is an effective method for improving the surface properties of titanium. The aim of this study was to investigate the bioactivity and corrosion behavior of MAO coatings containing strontium, which is beneficial for ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes an investigation of electrodeposited Zn-14% Ni and aluminium-based SermeTel 1140/962 coatings as possible replacements for cadmium. Slow strain rate tests were performed to measure the extent of direct hydrogen embrittlement of a high strength steel substrate as a result of the coating process and of hydrogen re-embrittlement caused by coating corrosion. The level of re-embrittlement was shown to depend on both the electrochemical potential of the coating and its barrier properties. Zn-14% Ni coatings caused the most re-embrittlement as they had the most active potential and contained through-thickness defects which left the steel exposed to hydrogen uptake. The microstructure of the high strength steel was also shown to be an important factor affecting the extent of embrittlement. AerMet 100 steel was more resistant than 300M steel and this was attributed to ...

Energy Technology Data Exchange (ETDEWEB)

Several types of coatings have previously been visually identified on the surface of 105-K East and 105-K West Basins fuel elements. One type of coating (found only in K West Basin) in particular was found to be a thick translucent material that was often seen to be dislodged from the elements as flakes when the elements were handled during visual examinations (Pitner 1997). Subsequently it was determined (for one element only in a hot cell) that this material, in the dry condition, could easily be removed from the element using a scraping tool. The coating was identified as Al(OH){sub 3} through X-ray diffraction (XRD) analyses and to be approximately 60 {micro}m thick via scanning electron microscopy (SEM). However, brushing under water in the basin using numerous mechanical strokes failed to satisfactorily remove these coatings in their thickest form as judged by appearance. Such brushing was done ...

International Nuclear Information System (INIS)

The photon rupture method, by which oxide film and metal are removed by focused pulsed Nd-YAG laser beam irradiation, was applied to form artificial micro-pits in Zn-5 mass% Al alloy-coated steel. The zinc alloy-coated layer was removed by pulsed laser irradiation treatment for about one second in a neutral buffer solution with NaCl. The rest potential transient with the laser treatment was measured. In the early stage of the laser treatment the rest potential of zinc alloy-coated steel changed to the negative direction immediately after every irradiation of a laser pulse and then returned to the previous value. However, after the steel substrate was exposed to the solution, the rest potential moved to the positive direction immediately after every irradiation of a laser pulse and then returned to the previous value. The amplitude and duration of the potential change after the laser irradiation increased with repetition of ...

Energy Technology Data Exchange (ETDEWEB)

Lower cost painting flock-like in appearance and touch feeling was developed as a new surface softening method for automobile interior plastic molded parts. The base coat with the same color as piles mixed into a top coat was first painted on the surface of a plastic molded part after cleaning, and after the top coat with less pitch mixed with piles was painted on the wet base coat and dried by a heater, excess piles were removed with suction and air blowing to produce flock-like appearance. Nylon 66 of 0.4mm in length was used as piles, and mixed into the top coat by 8.0wt% in content. This painting method was applicable to even such parts as one with a complex configuration, and one impossible to set piles on it by conventional methods because of poor durability. As a certain amount of piles with different colors were mixed into the top coat, sprinkly colored ...

Energy Technology Data Exchange (ETDEWEB)

This document outlines the Maintenance Implementation Plan (MIP) for the Plutonium Finishing Plant (PFP) located at the Hanford site at Richland, Washington. This MIP describes the PFP maintenance program relative to DOE order 4330.4B. The MIP defines the key actions needed to meet the guidelines of the Order to produce a cost-effective and efficient maintenance program. A previous report identified the presence of significant quantities of Pu-bearing materials within PFP that pose risks to workers. PFP`s current mission is to develop, install and operate processes which will mitigate these risks. The PFP Maintenance strategy is to equip the facility with systems and equipment able to sustain scheduled PFP operations. The current operating run is scheduled to last seven years. Activities following the stabilization operation will involve an Environmental Impact Statement (EIS) to determine future plant activities. This strategy includes long-term maintenance of the ...

Energy Technology Data Exchange (ETDEWEB)

Semiconducting properties of passive films formed on AISI 304 stainless steel grade were investigated by capacitances measurements in chloride containing aqueous solutions for different surface finishes: BA (bright annealing in hydrogen containing atmospheres) and 2B (standard annealing in oxidising atmospheres followed by pickling in acid, then water rinsing). Mott-Schottky analysis shows that for high enough electrode potential, and whatever the surface finish, the films behave like n-type semiconductors. 2B passive film appears to be more donor-doped than BA one and the density of donor states increases with chloride concentration. The electron donor levels are assumed to be generated by negatively charged cations vacancies produced by the chloride ions reaction with the outer passive film. This reaction looks easier for 2B than BA condition, which explains why BA resists better than 2B to pit nucleation.

Energy Technology Data Exchange (ETDEWEB)

The force exerted on the rotor by an active magnetic bearing (AMB) is determined by the current flow in the magnet coils. This force can be controlled very precisely, making magnetic bearings a potential benefit for grinding, where cutting forces act as external disturbances on the shaft, resulting in degraded part finish. It is possible to achieve precise shaft positioning, reduce vibration of the shaft caused by external disturbances, and even damp out resonant modes. Adaptive control is an appealing approach for these systems because the controller can tune itself to account for an unknown periodic disturbance, such as cutting or grinding forces, injected into the system. In this paper the authors show how one adaptive control algorithm can be applied to an AMB system with a periodic disturbance applied to the rotor. An adaptive algorithm was developed and implemented in both simulation and hardware, yielding significant reductions in rotor displacement in the ...

Energy Technology Data Exchange (ETDEWEB)

Researchers are developing polymer-based coating systems to reduce scaling and corrosion of air-cooled condensers that use a geothermal fluid spray for heat transfer augmentation. These coating systems act as barriers to corrosion to protect aluminum fins and steel tubing; they are formulated to resist the strong attachment of scale. Field tests have been done to determine the corrosion and scaling issues related to brine spraying and a promising organometallic polymer has been evaluated in salt spray tests.

Energy Technology Data Exchange (ETDEWEB)

A zinc/air battery is claimed whose performance is improved by omitting separating elements such as diaphragms etc. The cathode and anode spaces are separated by a collector with holes big enough to permit the electrons to pass freely while restraining the anode material. Further, the active material consists of a spherical care of inert material with a zinc coating. Under the zinc coating, the spherical particles have another thin coating of an electropositive material, e.g. nickel. The cell also contains means for circulating the anode suspension.

Energy Technology Data Exchange (ETDEWEB)

On the basis of cylindrical roller thrust bearings it was systematically examined to what extent PVD-coatings are able to take over the function of EP/AW-additives. The bearings were tested under heavy-duty conditions in order to distinguish very fast the efficiency of different coating-substrate-systems. Several coatings were tested for their ability to protect an un-coated counterpart. So just the washers of the roller bearings were coated, the rollers stayed un-coated. Four Me-C:H-coatings showed the best performance and fulfilled the required criterion for roller bearings in the boundary friction: low loss of mass and hardly surface deviation. Material carryover from the carbonaceous coating to the 100Cr6 steel surface was developed by the Me-C:H-coatings during the tests. This mechanism was able ...

Energy Technology Data Exchange (ETDEWEB)

We have continued to finish up our work on analyzing relationships between elastic properties and rock microstructure. We have worked on theoretical models for the effects of sorting and packing on elastic moduli and seismic velocities. After analyzing the scanning acoustic images of shales to quantify textures at different scales, we are now using theoretical inclusion models to quantify the elastic property variation with texture. In the closing phases of this project most of our efforts are now focused on writing up the results and preparing the final reports.

International Nuclear Information System (INIS)

By the methods of microstructural and electron-microscopic analyses by the tension test and impact test studied is the effect of quenching conditions on structure and mechanical properties of the TS6 titanium-#beta# alloy. It is shown that low temperature quenching from 700 deg C, recommended earlier for analogous VT15 titanium alloy, leads to appearence of intercrystalline fracture and to sharp decrease of impact strength of the TS6 alloy. Established are optimum conditions for quenching of half-finished products and articles of the TS6 alloy depending on their subsequent working or operation.

International Nuclear Information System (INIS)

Since the PWR plants in Japan have been operated more than 30 years, main instrumentation control equipment of analog systems has been renewed to digital control systems. Renewal works had to be done in short period within periodical inspection term and for several facilities. The Mitsubishi LTD group had been provided with these market needs by its digital control system (MELTAC-NplusR 3) applicable to main instrumentation control equipment for primary and secondary systems and had already finished the renewal for practical plants. (T. Tanaka)

International Nuclear Information System (INIS)

The necessity of the electron beam machine characterization via dose measurement is discussed. It includes a measurement of comprehensive dose distribution (at known X and Z axis) for verification of the machine performance. The acquired data were then used to develop the irradiation parameters such as energy, current, distance, conveyor speed, exposure rate and depth inside product to be irradiated. These parameters will be used as a guide for the routine irradiations. (Author)

Energy Technology Data Exchange (ETDEWEB)

A mathematical model of the multi machine electric power system to analyse its dynamics has been worked out. The effectivity of the power system stabilizer developed in the one machine system has been tested by means of this model. The influence of the arrangement of the stabilizers on the stability of the electric power system has also been investigated. High damping of electromechanical transient processes has been achieved. 7 refs., 1 tab., 5 figs.

Science.gov (United States)

An analysis of the diagnosis of loading and service dependability of a rail-mounted excavator used in surface lignite mining is described. Wheel power vibrations in electric motor bearings and electric motor input bearings to the gearbox were measured in situ, in horizontal, vertical, and axial directions. The data were analyzed using a mathematical relationship. The results are presented in a loading diagram that shows the deterioration and the acceptable lower bound of machine conditions over time. Work is continuing. 5 refs., 1 fig.

International Nuclear Information System (INIS)

An outline of the instrumentation and control systems associated with fuelling machines is given. The control systems such as hydraulic system, oil hydraulic system, electric control system and the remote control systems have been discussed in detail. The difference between RAPP and MAPP fuel handling control systems has been explained. A computer based system for the Narora fuel handling control system is also discussed. (S.K.K.).

Energy Technology Data Exchange (ETDEWEB)

Performance and emissions data were gathered on a normally aspirated single cylinder DI engine with various combinations of ceramic coatings installed. Thin ceramic thermal barrier coatings were applied to the piston crown and bowl, the head and valves, and the cylinder liner. The coated piston and head were run singly and in combination with the cylinder liner to investigate the effects of these different coated surfaces on emissions and performance. Coating the piston crown alone results in generally lower cylinder pressure, lower brake specific fuel consumption and lower NO(x) emission compared to the baseline engine. Soot emission is typically increased below 2000 RPM and decreased above 2000 RPM. Coating the head alone reduces cylinder pressure, but generally increases specific fuel consumption and NO(x) and soot emission. The KIVA-II code was used to model ...

International Nuclear Information System (INIS)

Jun 1973. 2 p. United States USAEC Directorate of Regulatory Standards,

Energy Technology Data Exchange (ETDEWEB)

Aluminium AA5182 coupons covered by a polyaniline film in the emeraldine base (EB) form showed increasing corrosion potential and decreasing corrosion current as a function of the thickness of the polymer layer. The cathodic reaction was proved not limited by diffusion of species inside the electrolyte solution and oxygen had no effect on the electrochemical behaviour of the coated samples. An EB coating on indium tin oxide conducting layer appeared slightly electroactive in neutral media. The IR spectra of aluminium coated samples, before and after heating in argon atmosphere, confirmed a redox reaction between the polymer film and the metal. This galvanic coupling can explain the good protective behaviour of emeraldine base against corrosion of aluminium.

Energy Technology Data Exchange (ETDEWEB)

The mechanical stability of diamond-like carbon (DLC) films coated on nitinol vascular stents was investigated under cyclic loading condition by employing a stent crimping system. DLC films were coated on the vascular stent of a three dimensional structure by using a hybrid ion beam system with rotating jig. The cracking or delamination of the DLC coating occurred dominantly near the hinge connecting the V-shaped segments of the stent where the maximum strain was induced by a cyclic loading of contraction and extension. However the failures were significantly suppressed as the amorphous Si (a-Si) buffer layer thickness increased. Interfacial adhesion strength was estimated from the spalled crack size in the DLC coating for various values of the a-Si buffer layer thickness.

UK PubMed Central (United Kingdom)

• Background and Aims The occurrence of stomata in seed coats is uncommon and there is limited information about their function(s). The aim of this study was to verify the distribution...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Polymer-coated magnetic nanoparticles (MNPs) have been prepared and used as an immobilization matrix for the fabrication of solid-state tris(2,2prime-bipyridyl)ruthenium(II) (Ru(bpy)32+) electrogenerated chemiluminescence (ECL) sensor. The pre-synthesized maghemite (g-Fe2O3) MNPs were coated with poly(3-thiopheneacetic acid) based on an oxidative polymerization method using KMnO4. The poly(3-thiopheneacetic acid)-coated MNPs have formed the clusters with average diameter of 200-500nm. The multilayer films of poly(3-thiopheneacetic acid)-coated MNPs were uniformly formed on the surface of a Pt electrode by an external magnet. The Ru(bpy)32+ was rapidly incorporated into the multilayer films within 5min through the electrostatic interaction between the Ru(bpy)32+ and the negatively charged c...

British Library Electronic Table of Contents (United Kingdom)

A test bench was designed and assembled to carry out impact tests on samples and components. The system allows simple and rapid adjustment of the test parameters, such as the shot size and air pressure, with good repeatability of the results. Tests on steel and light alloys were carried out under both as-produced condition and on thin hard-coated samples. Significant reductions in dimple dimensions were seen after coating. FE models simulating the experiments overestimated the dimple depths, although the parameter trend was satisfactorily captured. The residual stresses from coating and shot peening determined numerically are believed to have been proven effective against fatigue.

British Library Electronic Table of Contents (United Kingdom)

Fluorocarbon polymers are used to enhance thermal stability and electrostatic protection of composite propellant compositions. A precipitation technique has been developed to coat ammonium perchlorate (AP) using a copolymer of hexafluoropropylene and vinylidene fluoride (HFP-VF) with the help of solvent-counter solvent method. The coated AP has been used to prepare propellant compositions in different ratio based on hydroxyl terminated polybutadiene (HTPB), aluminium powder along with uncoated AP and studied for viscosity build-up and visco-elastic behaviour as well as mechanical, ballistic, thermal and sensitivity properties keeping 86% solid loading. The data on viscosity build-up indicate that as the percentage of viton coated AP increases end of mix viscosity and viscosity build-up inc...

International Nuclear Information System (INIS)

Plasma Technologies in Institute of Plasma Physics of the NSC KIPT are recently developed in the following directions. Material surfaces modification under their irradiation with pulsed plasma streams of different working gases. Besides traditional analysis of improvements of tribological characteristics and structural-phase changes of the modified layers recently we started investigations of material corrosions characteristic improvement under influence of pulsed plasma on the material surfaces. As to the surface coatings in arc discharges of Bulat type devices, new trends are related with multi-layers coatings, using Ti-AI-N coatings in cutting tools, using high frequency discharges or combined HF- and arc discharges for increasing the nomenclature of goods to be coated. Development of ozonators is respectively new area for IPP NSC KIPT. On the base of barrier high-frequency discharge there were ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study was to assess the energy flux and energetic balance related to the swine production and the recycling of residues generated by the system for utilization as organic fertilizers. The experiment was carried out at Vale dos Ipes Farm, located in the city of Ouro Verde do Oeste, in the Western of Parana State. One finishing phase swine unity containing 600 animals was monitored from January to June 2005. The treatment system is composed by one steel digester with capacity for 50 m{sup 3}, one sedimentation tank, one algae tank and one bio fertilizer storage tank. The swine barn cleaning is performed by dry scratching on a daily basis. The generated residues flow by gravitation through ducts towards the digester. The duration of the hydraulic retention period was 12 days. In the calculation of energetic efficiency, the energetic component ration is the greatest energetic cost in production system of finishing phase swine, ...

Energy Technology Data Exchange (ETDEWEB)

Micron-size Ni-base alloy (NBA) powders were mixed with both 1.5 wt.% (hereinafter %) micron-size CeO{sub 2} (m-CeO{sub 2}) and also 1.5% and 3.0% nano-size CeO{sub 2} (n- CeO{sub 2}) powders. These mixtures were coated on low-carbon steel (Q235) by 2.0 kW CO{sub 2} laser cladding. The effects on the microstructures, phases and electrochemical corrosion of the coatings upon the addition of m- and n- CeO{sub 2} powders to NBA (m- and n- CeO{sub 2} /NBA) have been investigated. The results showed that a smooth coating was prepared under suitable processing parameters (P= 2.0 kW, V= 180 mm min{sup -1}) by adding 1.5% n- CeO{sub 2}. In addition to the primary phases of {gamma}-Ni, Cr{sub 23} C{sub 6} and Ni{sub 3} B in the Ni-base alloy coating, CeNi{sub 3} was formed in Ni-base alloy coatings with both n- CeO{sub 2} and m-CeO{sub 2} particles, and CeNi{sub 5} appeared in the ...

Energy Technology Data Exchange (ETDEWEB)

PVD-coatings based on TiB{sub 2} are expected to show high wear resistance and low tendency of adhesion on metal forming tools. Coating adhesion and morphology can be modified over a wide range by varying the content of nitrogen (N{sub 2}) and the deposition parameters power and bias voltage. All coatings were deposited using commercial unbalanced magnetron equipment, the deposition was homogeneous in a volume of 400 x 400 x 400 mm{sup 3}. Hipped and hot pressed TiB{sub 2}-targets were used, nitrogen (N{sub 2}) was added as gas, Ti and Al by a solid Ti-Al-target. The tribological behaviour was tested by a pin-on-disc wear test. The coatings investigated were TiB{sub 2}, TiAlB(N), TiAl(N) and TiB{sub 2}/TiAl(N). As counterpart in the pin-on-disc wear test, 6 mm diameter spheres of steel (100Cr6), aluminium, brass and bronze were used. The experiments showed a non-uniform wear behaviour. For the ...

Energy Technology Data Exchange (ETDEWEB)

This Test Plan outlines the testing to be done on the Special Protective Coating (SPC) Polyurea which includes: Tank Waste Compatibility, Decontamination Factor Testing, and Adhesion Strength Testing after a sample has been exposed to Radiation.

International Nuclear Information System (INIS)

The effectiveness of an acrylic latex wall sealant in limiting the escape of radon from rock in underground mines is the subject of this paper. Application of the latex as a two-coat system over a fillter coat of gunite produced a reduction of radon concentration from an initial level of 80 to 100 pCi/L to a final average of 25 to 30 pCi/L under similar conditions.

Energy Technology Data Exchange (ETDEWEB)

Four subprojects were completed: development and evaluation of die coatings, accelerated die life characterization of die materials, evaluation of fluid flow and solidification modeling programs, selection and characterization of Al-based die casting alloys, and influence of die materials and coatings on die casting quality.

Energy Technology Data Exchange (ETDEWEB)

This heat exchanger is a critical step in the development of the Externally Fired Combined Cycle power system, a direct-coal combustion power plant (gas turbine). SiC is the only material with the needed resistance to creep, thermal shock, and oxidation; however a protective coating is needed. Ten candidate materials were identified: alumina-based materials, materials stable with SiO, and low expansion materials. An initial screening study should be performed.

Energy Technology Data Exchange (ETDEWEB)

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H{sub 2}SO{sub 4}+2 ppm F{sup -} simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 m{omega} cm{sup 2} that is ...

Energy Technology Data Exchange (ETDEWEB)

The dispersion of more than 20 vol pct submicrometer ceramic particles within a metallic matrix and the deposition of such a cermet to form a thick and tough coating presents problems. Most of the coating techniques have failed in attempting to homogeneously disperse very fine and hard particles in large amounts while avoiding their decomposition or reaction with the metal matrix during the deposition process. A simple and efficient method has been developed for producing ceramic-containing composite coatings. It consists in synthesizing cermet-based materials and in depositing them by a rapid solidification process, such as thermal spraying. Boride- and carbide-based materials have been successfully obtained by plasma spraying reactive powders comprising the basic reagents. These materials, with a microstructure of submicrometer ceramic particles dispersed in a metallic matrix, exhibit good wear-resistant properties ...

International Nuclear Information System (INIS)

There has been a growing interest in new laser systems for use at mid-infra-red wavelengths, driven by requirements for a number of diverse applications. Developments in mid-IR coating technology are following three major thrusts. In the first, the potential of ion-assisted process is being exploited and the technology is already becoming well established in the optical coating industry. In the second, the benefits of using gas-phase precursors are being explored, driven by the potential of avoiding the generation of second phase inclusion in the coatings with associated reduction in laser damage threshold. Research is also addressing the use of nanocomposite materials with an engineered microstructure to produce coatings with dielectric properties of choice. This paper presents a review of progress in some of these areas with special emphasis on the comparison of the properties of materials at DF laser ...

International Nuclear Information System (INIS)

This paper presents the first results on formation and study of structure and properties of micro- and nanocomposite combined coatings. By means of modeling the deposition processes (deposition conditions, current density-discharge, plasma composition and density, voltage) we formed the three-layer nanocomposite coatings of Ti-Al-N/Ti-N/Al_2O_3. The coating composition, structure and properties were studied using physical and nuclear-physical methods. The Rutherford proton and helium ion backscattering, scanning electron microscopy with microanalysis, grazing incidence X-ray diffraction, as well as nanohardness tests (hardness) were used. Measurements of wear resistance and corrosion resistance in NaCl, HCl and H_2SO_4 solutions were also performed. For testing mechanical properties such characteristics of layered structures as hardness H, elastic modulus E: H"3/E"2 etc. were measured. It is demonstrated that the formed ...

CERN Document Server

Non-evaporable thin film getters of various compositions have been produced by sputtering. Among about 20 materials which have been studied, the lowest activation temperature (about 180 degree C) has been displayed by a Ti-Zr-V coating obtained from a cathode made of intertwisted elemental wires. In order to optimize the vacuum properties of this film various production parameters, including the substrate temperature during coating, have been varied. The films have been characterized by pumping speed measurement, secondary electron microscopy, and X-ray diffraction. It has been found that the substrate coating temperature affects significantly the activation temperature, the pumping speed and the gas surface capacity. The highest pumping speed values, obtained for substrate coating temperatures of 250 degree C and 300 degree C, are clearly correlated with the increased surface roughness and porosity of ...

Energy Technology Data Exchange (ETDEWEB)

The properties of polycrystalline (Ti, Al)N coatings deposited on non-nitrided, classically plasma-nitrided and low pressure plasma-nitrided AISI H11 steel samples were investigated. The plasma deposition and low pressure plasma nitriding were performed in a Z700-LH magnetron sputter ion plating unit, while a separate unit was used for plasma nitriding of specimens at a pressure of several millibars. The (Ti, Al)N coating was deposited onto all the samples using the same equipment as for the plasma deposition and low pressure plasma nitriding. For the characterization of the composite structures, the following methods were used: scratch test, X-ray diffraction analysis, scanning electron microscopy, scanning tunnelling microscopy and microhardness testing. It was found that plasma nitriding prior to coating deposition strongly affects the growth and properties of hard coatings, such as the ...

Energy Technology Data Exchange (ETDEWEB)

A device for detecting neutrons includes a semi-insulated bulk semiconductor substrate having opposed polished surfaces. A blocking Schottky contact comprised of a series of metals such as Ti, Pt, Au, Ge, Pd, and Ni is formed on a first polished surface of the semiconductor substrate, while a low resistivity ("ohmic") contact comprised of metals such as Au, Ge, and Ni is formed on a second, opposed polished surface of the substrate. In one embodiment, n-type low resistivity pinout contacts comprised of an Au/Ge based eutectic alloy or multi-layered Pd/Ge/Ti/Au are also formed on the opposed polished surfaces and in contact with the Schottky and ohmic contacts. Disposed on the Schottky contact is a neutron reactive film, or coating, for detecting neutrons. The coating is comprised of a hydrogen rich polymer, such as a polyolefin or paraffin; lithium or lithium fluoride; or a heavy metal fissionable material. By varying the ...

Energy Technology Data Exchange (ETDEWEB)

Chromium containing amorphous hydrogenated carbon films (a-C : H/Cr) have been prepared by simultaneous rf plasma activated chemical vapour deposition of methane and magnetron sputtering of a chromium target. During deposition the substrates were heated (up to 300C) and DC biased (-200 and -600 V) in order to obtain films with high chemical stability. Constant temperature tests were performed at 250C in air with coatings deposited on silicon substrates. The degradation of the coatings was monitored by Raman spectroscopy and reflectance and transmission measurements. The main degradation mechanisms are discussed and the relevant parameters which improve the durability of the coatings are presented. Furthermore, the durability of solar selective, multilayered coatings which were deposited on copper sheets was investigated. Based on accelerated aging tests at different temperature loads in air (at 220C, ...

CERN Document Server

Two quantities play a central role in that part of nonlinear optics which deals with the effects of a finite momentum spread in a particle beam: the orbit position whose derivative with respect to momentum is called 'orbit dispersion' and the betatron wave number whose derivative WRT momentum is the 'chromaticity'. The orbit dispersion varies with the azimuth and is essentially horizontal in a machine with a horizontal symmetry plane; parasitic radial fields induce a vertical component. The chromaticity is a scalar quantity related to the integral of the focusing strength, over one turn of the machine; it is defined for the horizontal and vertical planes. After recalling the general motion equation in the horizontal plane, the orbit dispersion and the chromaticity will be treated. Closed formulae are given for lumped elements and special emphasis is put on dipoles with a high deflection angle. (8 refs).

International Nuclear Information System (INIS)

The basic relationships of the convolution/superposition dose calculation technique are reviewed, and a modelling technique that can be used for obtaining a satisfactory beam model for a commercially available convolution/superposition-based treatment planning system is described. A fluence energy spectrum for a Co-60 treatment machine obtained from a Monte Carlo simulation was used for modelling the fluence spectrum for a Rokus M machine. In order to achieve this model we measured the depth dose distribution and the dose profiles with a Wellhofer dosimetry system. The primary fluence was iteratively modelled by comparing the computed depth dose curves and beam profiles with the depth dose curves and crossbeam profiles measured in a water phantom. The objective of beam modelling is to build a model of the primary fluence that the patient is exposed to, which can then be used for the calculation of the dose deposited in the patient. (authors)

Energy Technology Data Exchange (ETDEWEB)

Metal machining facilities pose interesting design problems. This article provides an overview of key environmental control considerations and ways to deal with them. Machine shops offer a variety of environmental control challenges to mechanical engineers. Among the design problems that must be considered include: whether to provide space heating only or year-round air conditioning; temperature and relative humidity requirements; air cleanliness; exhaust air requirements; the type of HVAC system to be used; industrial waste and plumbing considerations; compressed air needs; and noise control. In addition, the designer must comply with worker health and safety and environmental protection regulations set forth by the National Institute of Safety and Health (NIOSH), OSHA, and EPA, as well as with any applicable state and local requirements.

International Nuclear Information System (INIS)

Fibre-reinforced-polymer-composite material has been suggested as a bearing material to overcome tribological problems witnessed during the testing of Ram assembly of the 540 MWe fuelling machine at RTD. After successful trials at B-Ram the composite material has been adapted for B-RAM, C-Ram and RDB head at fuelling machines being tested at RTD, Hall 7 and at Tarapur. Laboratory evaluations were also carried out at Tribology Lab RTD to study effect of radiation on the composite. Paper deals with the various aspects of life prediction of this material in term of wear and radiation damage. (author)

Wastenet

of early humanitarians, and the vivisectors turned to Rene Descartes (1596 1650 ) to justify ...A celebrated mathematician, physiologist, and psychologist, Descartes provided a general philosophy of the irrelevance of ethics to the ...Animals, according to Descartes, were insensible and irrational machines; moved, like clocks, but

UK PubMed Central (United Kingdom)

IntroductionRecent Food and Drug Administration legislation enables the mandating of product performance standards for cigarette smoke and the evaluation of manufacturers’...Full Text Available

UK PubMed Central (United Kingdom)

Skin sensitization is the most commonly reported occupational illness, causing much suffering to a wide range of people. Identification and labeling of environmental allergens is urgently required to...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This guide explained the requirements for Off-Road Compression Ignition Engine Emission Regulations established under the Canadian Environmental Protection Act. The regulations are enforced by Environment Canada, which authorizes and monitors the use of the national emissions mark. The regulations prescribe standards for off-road engines that operate as reciprocating, internal combustion engines, other than those that operate under characteristics similar to the Otto combustion cycle and that use a spark plug or other sparking device. The regulations apply to engines that are typically diesel-fuelled and found in construction, mining, farming and forestry machines such as tractors, excavators and log skidders. Four different types of persons are potentially affected by the regulations: Canadian engine manufacturers; distributors of Canadian engines or machines containing Canadian engines; importers of engines or machines ...

Energy Technology Data Exchange (ETDEWEB)

To keep up with the speeds of modern production lines, most machine vision applications require very powerful computers (often parallel-processing machines), which process millions of points of data in real time. The human brain performs approximately 100 billion logical floating-point operations each second. That is 400 times the speed of a Cray-1 supercomputer. The right software must be developed for parallel-processing computers. The NSF has awarded Rensselaer Polytechnic Institute (Troy, N.Y.) a $2 million grant for parallel- and image-processing software research. Over the last 15 years, Rensselaer has been conducting image-processing research, including work with high-definition TV (HDTV) and image coding and understanding. A similar NSF grant has been awarded to Michigan State University (East Lansing, Mich.) Neural networks are supposed to emulate human learning patterns. These networks and their hardware implementations ...

International Nuclear Information System (INIS)

The patent relates to fluid operated devices for moving articles. The machine may be used in filling a nuclear fuel canister with fuel pellets where there is a tendency for out of squareness of pellets to produce a jam condition readily cleared by a modest force. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

The subject of FDD (fault detection and diagnosis) has gained widespread industrial interest in machine condition monitoring applications. This is mainly due to the potential advantage to be achieved from reduced maintenance costs, improved productivity and increased machine availability. This paper presents a new FDD scheme for condition machinery of an industrial steam turbine using a data fusion methodology. Fusion of a SVM (support vector machine) classifier with an ANFIS (adaptive neuro-fuzzy inference system) classifier, integrated into a common framework, is utilized to enhance the fault detection and diagnostic tasks. For this purpose, a multi-attribute data is fused into aggregated values of a single attribute by OWA (ordered weighted averaging) operators. The simulation studies indicate that the resulting fusion-based scheme outperforms the individual SVM and ANFIS systems to detect and diagnose incipient steam ...

Energy Technology Data Exchange (ETDEWEB)

Research indicates that diesel equipment can be used safely in undergound coal mines provided that certain conditions prevail. These conditions are: the machines and engines are approved for underground use, an adequate maintenance and training program is in effect, an adequate monitoring system with proper instrumentation is used, and adequate ventilation is maintained.

Science.gov (United States)

One of the tasks comprising ERDA Contract EY-76-S-02-2840, ''Minimization of Cupola Energy and Air Pollution,'' has been the carrying out of a comprehensive survey of world literature relating to the cupola furnace for melting of cast iron. It was decided...

Energy Technology Data Exchange (ETDEWEB)

Kerf geometry, kerf wall features, and cutting front characteristics of an Abrasive Waterjet (AWJ) machined Graphite/Epoxy (Gr/Ep) laminate were studied. A macroscopic analyses suggests that geometrical features associated with AWJ machining of Gr/Ep laminates are influenced by three macro regions along the cutting depth. The presence of these regions, including initial damage at jet entry, smooth cutting, and rough cutting near the jet exit, depends on the operating conditions. Design of experiments and analysis of variance were used to determine the effect of cutting parameters on kerf characteristics and to develop empirical models for kerf profile and features of the three distinct macroscopic regions. Cutting front analysis revealed that the mechanisms of material removal in AWJ machining of Gr/Ep do not change over the jet penetration depth. In general, high quality uniform cuts may be obtained by minimizing initial ...

Science.gov (United States)

...position to receive material. (2) Self-loading haulage equipment used as a loading machine. In working places in which self-loading haulage equipment is operated to load material, the areas which...

Energy Technology Data Exchange (ETDEWEB)

CeO{sub 2}-coated LiMn{sub 2}O{sub 4} spinel cathode was synthesized using two-step synthesis method. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. The results of the electrochemical performances on CeO{sub 2}-coated electrode are compared to those of electrodes based on LiMn{sub 2}O{sub 4} spinel without CeO{sub 2} coating. CeO{sub 2}-coated LiMn{sub 2}O{sub 4} cathode improved the cycling stability of the electrode. The capacity retention of 2 wt% CeO{sub 2}-coated LiMn{sub 2}O{sub 4} was more than 82% after 150 cycles between 3.0 and 4.4 V at room temperature and 82% after 40 cycles at elevated temperature of 60 C. The amounts of dissolved manganese-ions in CeO{sub 2}-coated LiMn{sub 2}O{sub 4} significantly are smaller than pristine LiMn{sub 2}O{sub 4} systems especially at elevated temperatures. ...

Energy Technology Data Exchange (ETDEWEB)

The possibilities to electrodeposit thick coatings composed of nanoparticles of Sb and Sb{sub 2}O{sub 3} for use as high-capacity anode materials in Li-ion batteries have been investigated. It is demonstrated that the stability of the coatings depends on their Sb{sub 2}O{sub 3} concentrations as well as microstructure. The electrodeposition reactions in electrolytes with different pH and buffer capacities were studied using chronopotentiometry and electrochemical quartz crystal microbalance measurements. The obtained deposits, which were characterised with XRD and SEM, were also tested as anode materials in Li-ion batteries. The influence of the pH and buffer capacity of the deposition solution on the composition and particle size of the deposits were studied and it is concluded that depositions from a poorly buffered solution of antimony-tartrate give rise to good anode materials due to the inclusion of precipitated Sb{sub 2}O{sub 3} ...

Energy Technology Data Exchange (ETDEWEB)

Electric utilities are actively seeking ways of optimizing the economics of their operations by improving productivity and reducing time and money spent on maintenance. Iberdrola, a Spanish utility, is using advanced machine condition-monitoring technology to centralize control and maintenance of its hydropower projects as a means of achieving those goals. The company is using a blend of technologies to supervise their projects from a regional control center. The monitoring scheme makes use of data from on-line, machine-condition monitors, displays from in-plant audio asnd video equipment, and analysis from the control center`s SCADA system.

Energy Technology Data Exchange (ETDEWEB)

Recent research work on adjustable speed pumped storage plants conducted in Japan, the USA and Europe suggests that they have many advantages over fixed-speed plants, and can contribute to power system regulation even in pump mode. This paper describes two types of static frequency converter for such pumped storage plants, especially those with greatly fluctuating heads. The design characteristics and operation of the doubly fed induction machine and the synchronous machine with DC link converter are set out and the devices compared. (UK)

Energy Technology Data Exchange (ETDEWEB)

In this paper, power system stabilizer design for multi-machine power systems is translated into an equivalent problem of decentralized controller design for Multi-Output Multi-Input (MIMO) control systems. Subject to a condition based on the structured singular values, each stabilizer can be designed independently. Within this general framework, the conventional stabilizer design methodology based on the concept of synchronous and damping torques is used to decide the design details of each stabilizer. The suggested design method is applied to a model of a practical 10 machine power system. (author)

Energy Technology Data Exchange (ETDEWEB)

A simple but powerful inter-process communication machine is presented for programming direct shared memory multiprocessor machines in medium and low level application areas and in particular, for the programming of embedded systems such as intelligent instrumentation and online controllers. The primitives are based on hoare's concept of tightly synchronised data transfer to provide mutual exclusion and synchronisation in a single mechanism. The design of these primitives is discussed with reference to a number of criteria considered appropriate to the application area and their implementation in the Cyba-M multi-microprocessor research is described. 10 references.

Energy Technology Data Exchange (ETDEWEB)

Software to aid the distribution and coordination of tasks between different processors was developed to distribute applications written in Fortran. This development led to the discovery of problems unique to Fortran and to interesting practical solutions. Two graphical applications were distributed to a variety of machines and machine pairs: CDC 7600-LSI/11, CRAY-LSI/11, VAX 11/780, and Apollo. These distributions pointed out several parameters such as the use of Fortran COMMON, communication parameters, and processing capabilities that can affect the successful distribution of applications.

Energy Technology Data Exchange (ETDEWEB)

This paper proposes the design of LQ-PSS (linear quadratic power system stabilizer) for improving power system stability using genetic algorithm(GA). We are turned weighting matrices of LQ-PSS using GA. To evaluate the usefulness of the proposed method, we performed the nonlinear simulation on a single machine infinite system. As results on a single machine infinite system. As results of the simulation, the proposed method shows the better control performance than CPSS(conventional power system stabilizer) in terms of settling time and damping effects. (author). 7 refs., 7 figs., 3 tabs.

International Nuclear Information System (INIS)

In order to prevent corrosion failures of machines and structures, it is desirable to know in advance when the corrosion damage will take place, and appropriate measures are needed to mitigate the damage. The corrosion predictions are needed both at development as well as operational stage of machines and structures. There are several forms of corrosion process through which varying degrees of damage can occur. Under certain conditions these corrosion processes at alone and in other set of conditions, several of these processes may occur simultaneously. For a certain type of machine elements and structures, such as gears, bearing, tubes, pipelines, containers, storage tanks etc., are particularly prone to pitting corrosion which is an insidious form of corrosion. The corrosion predictions are usually based on experimental results obtained from test coupons and/or field experiences of similar machines or ...

Energy Technology Data Exchange (ETDEWEB)

Silica microspheres were deposited into two-dimensional periodic arrays and coated with a thin layer of silicon nanocrystals. The luminescence from the silicon nanocrystals coupled into the whispering gallery modes of the spheres, with Q factors that depended on a range of parameters including sphere size, position on the sphere, viewing direction, and thickness of the nanocrystal coating. Scattering from the film-sphere and/or the sphere-substrate contacts resulted in a lower Q for modes that intersect these regions. The highest Q factors obtained in this work were {approx}1500. The results suggest that silica microspheres may be promising candidates for high-Q cavities that incorporate silicon nanocrystals for cavity QED or nonlinear optical effects.

Energy Technology Data Exchange (ETDEWEB)

Steel structures immersed in seawater are protected from corrosion using cathodic protection systems (sacrificial anodes or impressed current), by paint coatings or by duplex systems in which cathodic protection hinders corrosion at coating's failure sites. The main problem related to those duplex systems is how to avoid cathodic delamination due to the alkalinity generated at cathodic sites. The present paper analyses the effectiveness of red mud suspensions as pre-treatment to avoid cathodic delamination. The study was conducted using mainly electrochemical impedance spectroscopy (EIS). The evolution of the electrode potential with immersion time was also recorded because it concerns the practical aspect of current density necessary to reach the protection potential. The study shows that red mud pre-treatments are effective in avoiding coating's delamination. (author)

Energy Technology Data Exchange (ETDEWEB)

Anti-reflective coatings made with Teflon AF2400 had the highest damage thresholds recorded for physical vapor deposited coatings at the Lawrence Livermore National Laboratory damage facility. Physical vapor deposited layers of Teflon AF2400, a perfluorinated amorphous polymer, maintained the bulk optical properties of a high transmittance from 200 nm to 1600 nm, and a low refractive index. In addition, the refractive index can be intentionally reduced by control of two common deposition parameters, deposition rate and substrate temperature. Scanning electron microscopy and nuclear magnetic resonance observations indicated that morphological changes caused the variations in the refractive index rather than compositional changes. The coatings adhered to fused silica and silicon wafers under normal laboratory handling conditions.

International Nuclear Information System (INIS)

Full text: Institute for Nuclear Research, Pitesti-Mioveni, Romania in direct cooperation with the National Institute for Laser, Plasma and Radiation Physics, Magurele, Bucharest studied and prepared for coating more than 1000 tiles made of Inconel with 7-9 #mu#m of beryllium for nuclear fusion applications at JET, Culham, UK. The principles of manufacturing processes using thermal evaporation and plasma ignited in pure metal vapors as well as by Thermionic Vacuum Arc (TVA) method and the properties of the Ni and Be coatings are presented. The prepared beryllium layers were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. (authors)

Energy Technology Data Exchange (ETDEWEB)

Kawasaki Steel has constructed many facilities for 15 years to produce cold rolled products and galvanized products in Mizushima Works and Chiba Works. To efficiently and stably produce high and uniform quality products, various new control methods have been developed and applied to these new facilities. Especially, temperature control in a continuous annealing line, zinc coating control in a continuous galvanizing line or paint coating control in a multi-purpose coating line and tension control to achieve stable processing are the most advanced technologies and are introduced in this paper. (author)

British Library Electronic Table of Contents (United Kingdom)

This paper presents a combined experimental and computational study into the aerodynamics and performance of a small scale vertical axis wind turbine (VAWT). Wind tunnel tests were carried out to ascertain overall performance of the turbine and two- and three-dimensional unsteady computational fluid dynamics (CFD) models were generated to help understand the aerodynamics of this performance. Wind tunnel performance results are presented for cases of different wind velocity, tip-speed ratio and solidity as well as rotor blade surface finish. It is shown experimentally that the surface roughness on the turbine rotor blades has a significant effect on performance. Below a critical wind speed (Reynolds number of 30,000) the performance of the turbine is degraded by a smooth rotor surface finis...

International Nuclear Information System (INIS)

In the Peruvian natural forest there are several kind of woods, some of those are not of commercial interest, because have not resistance at termites and wet, are too soft, or can not be well finished, in the others. The present work is devoted to improvement of the physical properties of wood, such as hardness, traction, wet resistance, etc., by means of the generation of a composite wood-polymers cured by using gamma irradiation. The main objective is to establish the main parameters for the polymerization process (economic technical aspect) that decrease the amount of water absorption, in consequence the volumetric variation of Catahua, Mohena and Capirona woods. Gamma irradiation also provides good protection against the biological agents. In consequence, these woods increase its intrinsic and economic values. (author)

Energy Technology Data Exchange (ETDEWEB)

The use of selective additives such as MgO as a sintering aid and a rare earth oxide as a grain growth inhibitor, has allowed the manufacture of beryllia ceramics having close to theoretical density. The grain size and grain size distribution can be controlled by an optimum firing schedule leaving a remnant porosity which is extremely fine (0.2 {mu}m). This structure is compared with conventional BeO ceramics, densified by liquid phase sintering, which develops a glassy grain boundary and retains large pores up to 3 {mu}m. The significantly improved strength properties, extremely fine pores,the 'pinning effect' of rare earth oxide, and the superior surface finish both in the as-fired and polished state are discussed in relation to the micro-structure. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Work on the coke oven gas cleaning demonstration project (CCT-11) this quarter has focused on Phase IIB tasks, and include engineering, construction, and training. Additionally, plans for changes in the operating schedule of the coke plant that affect the demonstration project are described. The project Milestone Schedule and Log is shown. Planned Baseline Supplemental Monitoring activities described in the Environmental Monitoring Plan were completed. Testing of the mechanical systems began in June, 1991. The cold commissioning date has been moved back from October 1, 1991 to November 1, 1991 to allow float for miscellaneous finish-up items beyond the electrical contractor`s projected completion date of October 31, 1991.

International Nuclear Information System (INIS)

Modern day accelerator development encompasses a myriad technologies required for their diverse needs. Whereas RF, high voltage, vacuum, cryogenics etc., technologies meet their functional requirements, high finish lapping processes, ceramic-metal joining, oven brazing, spark erosion or wire cutting etc., are a must to meet their fabrication requirements. Electromagnetic (EM) forming technique falls in the latter category and is developed as a special technology. It is currently catering to the development as a nuclear reactor technology, but has the potential to meet accelerator requirements too. This paper highlights the general principle of its working, simple design guidelines, advantages, and suggests some specific areas where this could benefit accelerator technologies

Energy Technology Data Exchange (ETDEWEB)

At present the cooler synchrotron COSY a synchrotron and storage ring for medium energy physics is being commissioned at Juelich. The construction of the ring was finished during September 1992. The cooler ring will deliver protons in the momentum range from 270 to 3300 MeV/c. The phase density of the circulating protons will be increased with electron cooling at injection and with stochastic cooling at momenta between 1500 and 3300 MeV/c. High luminosity internal experiments as well as high resolution external experiments will be possible. Details of the lattice, to match the different ion optical requirements for cooling, acceleration, internal experiments and ultra-slow extraction will be discussed. An overview of the performance of the ion sources, the injector cyclotron, the ring, the injection beamline are given. The realization status of the extraction beamlines to the external experimental area is given. The experience on the commissioning of the cooler ...

International Nuclear Information System (INIS)

One of the requirements for uniform field quality in the SSC dipole magnets is the consistency in the superconducting strand characteristics from start to finish to the production phase. As full scale production of strand and cable approaches, the consistency in performance of the early batches of conductor needs to be examined. A number of 300 mm billets have been manufactured at IGC with tight process controls. The performance of the final conductor in terms of piece lengths, current density, Cu/Sc ratio and wire diameter has been evaluated. The data are analyzed in order to understand the variations that are related to the conductor design and processing. In this paper the current density of the strand is examined over the length of the billet to determine inherent variability in the Nb/Ti alloy itself.

Science.gov (United States)

Oct 20, 1997 ... The following requirements apply to the solar array: ..... housings will be coated with material meeting the program's outgassing requirements. ... The solar array temperature testing requirements will be determined by analysis. .... The ADS also generates attitude products for the project and science team. ...

Energy Technology Data Exchange (ETDEWEB)

In the present paper the tribological behavior of the coatings are discussed. Duplex coatings were applied on cold working steel 100Cr6. Samples were plasma nitrided at different thickness of plasma surface layers. TiN was deposited with a classic BALZERS PVD equipment and subsequent ion implantation. Ion implantation was provided with N{sup 5+} ions. The other samples were produced with IBAD technology in DANFYSIK chamber. Wear resistance and exchanges of friction coefficient were measured with on-line test using special designed tribology equipment. Following the tests, the wear zone morphology and characteristics of surface layer structure as well as important properties were investigated by scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). Scratch adhesion testing was performed using commercially available equipment. Energy dispersive X-ray analysis (EDAX) of the wear-scars on pins provided essential information on ...

Energy Technology Data Exchange (ETDEWEB)

We tried to apply a quartz crystal as a sensor by using the resonant frequency and the resistance properties of quartz crystals. Four kinds of fatty acids that have the same head groups were coated on the surfaces of the quartz crystals, and the shift of the resonant frequency and the resistance were observed based on the lengths of the tail groups. Myristic acid (C{sub 14}), palmitic acid (C{sub 16}), stearic acid (C{sub 18}), and arachidic acid (C{sub 20}) were deposited on the surfaces of quartz crystals by using the Langmuir-Blodgett (LB) method. As a result, the resonant frequency change was more sensitive to high molecular-weight fatty acids than to low molecular-weight ones. We also observed the effect of temperature on stearic acid LB films, and the response properties of quartz crystals coated with stearic-acid LB films to organic gases were investigated. As a result, the sensitivity of quartz crystals to organic gases was higher for ...

UK PubMed Central (United Kingdom)

In recent years, the interest in the use of bacteria for biological control of plant-pathogenic fungi has increased. We studied the possible side effects of coating barley seeds with the antagonistic...Full Text Available

UK PubMed Central (United Kingdom)

An immunoassay employing ¹²⁵I-labeled enterotoxin B and polystyrene tubes coated with specific antibody was used for assaying purified and crude enterotoxin. Antibody was adsorbed to untreated...Full Text Available

UK PubMed Central (United Kingdom)

Enzymes are versatile catalysts in laboratories and on an industrial scale; improving their immobilization would be beneficial to broadening their applicability and ensuring their (re)use. Lipid-coated...Full Text Available