International Nuclear Information System (INIS)

We have obtained radial velocities for 69 stars in the globular cluster M2 (NGC 7089). M2's rotation axis is, within sizeable uncertainties, perpendicular to the major axis determined by the flattening. The ratio of rotational to random kinetic energy agrees with that predicted from the ellipticity assuming an oblate figure and an isotropic velocity-dispersion tensor. We have fitted King-Michie models to determine M2's mass, the exponent of an assumed power-law mass function, and the anisotropy radius. The most significant sources of uncertainty in the modeling are the velocity dispersion, the distance, and the mass-luminosity relation for the cluster stars. The models favor mass functions similar to or shallower than the Salpeter initial-mass function and a moderate amount of velocity anisotropy.

International Nuclear Information System (INIS)

The author describes the results of post-test analyses of PANDA transient (M-series) tests M2 and M3. The purpose of the PANDA post-test analysis activity is to demonstrate that TRACG is applicable for the calculation of long-term SBWR containment response to a LOCA. Comparisons between TRACG predictions and test measurements are presented and discussed in the dual context of what the test results show and the capability of TRACG to predict their key features

International Nuclear Information System (INIS)

The ecological effects of acid mine drainage were investigated during the summer of 1993 on St. Kevin Gulch, a headwater stream near Leadville, Colorado. The stream currently receives acidic water from an abandoned mine. The pH downstream of the mine is between 3.5 and 4.5, and several metals exceed concentrations toxic to aquatic organisms. Zinc is present at especially high concentrations (1 to 10 mg/L) Furthermore, the stream bottom is covered with a thick layer of iron hydroxide precipitates. Effects on stream biota have been dramatic. Aquatic flora in the affected reach is limited to a green filamentous alga, Ulothrix subtilissima. Macroinvertebrate densities are significantly lower in the affected reach (mean = 99 indiv/m"2; SD = 88 indiv/M"2) compared to an upstream (pristine) reference reach (mean = 1,735 indiv/m"2; SD = 652 ...

International Nuclear Information System (INIS)

The surface permeability of concrete walls and floors in houses was measured with a specially designed permeameter, based on measuring the air-flow induced by a pressure difference across a temporary test seal applied to a surface. The permeability of bulk concrete is 10"-"1"6 m"2. Areas free of surface defects had permeability ranging from 10"-"1"4 to 10-"1"6 m"2. However, surface defects are common on concrete wall surfaces, which increase the permeability to >10"-"1"2 m"2. This is too high for standard seal designs to be adequate as the only method of soil gas and radon exclusion. Satisfactory seals require either extended contact width or mechanical removal of the surface layer. (orig.). (2 figs., 1 tab.).

International Nuclear Information System (INIS)

Determination of the specific surface of uranium oxides: UO_2 and U_3O_8 using a simplified equation derived from the Brunauer, Emmett and Teller theory. The method is suitable for samples having a surface between 6 to 50 m"2.

International Nuclear Information System (INIS)

Radon has been recognized by various international health organizations as a major lung carcinogen. The onset of cellular carcinogenesis involves DNA damage to bronchi epithelial cells by particles emitted by radon progeny. Radon diffusion is an important release mechanism for radon that is produced inside a building material. The physical parameter that characterizes this process is the radon diffusion Coefficient D(m-2 s-l). The diffusion constant and Diffusion length has been measured as 2.15xl0- 6 m-2s-1, 1.01m for soil, 1.65x10-6m-2s-1, 0.89m for sand and 0.21x 10-6m-2s-1, 0.31m for crush aggregate saudi building materials respectively. The values are found to be minimum for crush aggregates, which shows that crush aggregate is least permeable to radon flow as compared with the other building materials studied. ...

British Library Electronic Table of Contents (United Kingdom)

The wind speed distribution and wind energy potential are investigated in three selected locations in Oyo state using wind speed data that span between 12 and 20 years measured at 10 m height. In addition, the performance of selected small to medium size wind turbines in these sites were examined. The annual energy output and capacity factor for these turbines were determined. It was found that the monthly mean wind speeds in Oyo state ranges from 2.85 m/s to 5.20 m/s. While the monthly mean power density varies between 27.08 W/m2 and 164.48 W/m2, while the annual mean power density is in the range of 67.28 W/m2 and 106.60 W/m2. Based on annual energy output, wind turbines with cut-in wind speed of about 2.5 m/s and moderate rated wind speeds will be best suited for all the sites.

British Library Electronic Table of Contents (United Kingdom)

The diffusion of linalool and methylchavicol from thin (45-50 mm) antimicrobial low-density polyethylene-based films was evaluated after immersion in isooctane and the effect of temperature (4, 10, or 25 degreeC) on the diffusion rate was evaluated. The kinetics of linalool and methylchavicol release showed a non-Fickian behavior at the lowest temperature. An increase in temperature from 4 degreeC to 25 degreeC resulted in an increase in the diffusion coefficient from 4.2 x 10-13 m2 s-1 to 2.5 x 10-12 m2 s-1 for linalool and from 3.5 x 10-13 m2 s-1 to 1.1 x 10-12 m2 s-1 for methylchavicol. The effect of temperature on the diffusion coefficient followed an Arrhenius-type model (r2 = 0.972) in relation to a time-response function with a Hill coefficient. Activation energies of 57.8 kJ mol-1 ...

International Nuclear Information System (INIS)

Crystallization points of aqueous solution of the systems M(ClO_4)_2-H_2O (M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+), depending on the salt concentration, were identified by visual-polythermal method. Relying on model notions on the structure of the electrolyte solutions, specific features of strontium perchlorate solubility polytherm and concentration dependence of the relative dynamic viscosity of the salt aqueous solutions are discussed

CERN Document Server

We study the impact of very light sterile neutrinos (Delta m^2_new around 1 to 10 times 10^(-2) eV^2, sin^2 2theta_new<10^(-1)) on upcoming theta_13-driven reactor antineutrino experiments like Double-CHOOZ and Daya Bay. Oscillations driven by these vales of Delta m^2_new affect data in the near and far detectors differently and hence potentially modify the capability of these experimental setups to constrain and measure sin^2 2theta_13. We find that the hypothesis theta_new different from zero negatively impacts one's ability to either place an upper bound on sin^2 2theta_13 in the advent of no oscillation signal or measure sin^2 2theta_13 if a theta_13-driven signal is observed. The impact of sterile neutrino effects, however, depends significantly on one's ability to measure the recoil positron energy spectrum. If sin^2 2theta_new is larger than 10^(-2), upcoming theta_13-driven reactor ...

British Library Electronic Table of Contents (United Kingdom)

Summary The purpose of this study was to evaluate the efficacy of postoperative adjuvant chemotherapy with FOLFOX regimen on the outcome after LT for HCC patients who did not meet the Milan criteria. Ninety-five consecutive HCC patients with liver cirrhosis undergoing LT were enrolled. Fifty-eight who did not meet the Milan criteria were randomized to open-label treatment with or without adjuvant chemotherapy after LT (n?=?29/group). The FOLFOX chemotherapy protocol comprised 3-week cycles of oxaliplatin 100?mg/m2 on day 1, leucovorin (calcium folinate, CF) 200?mg/m2 on day 1 followed by 3-day, and 5-fluorouracil (5-FU) 2000?mg/m2 as a 48-h continuous infusion, for up to six courses in the 1st year after transplantation. Median survival was extended by 4.57?months by combination chemothera...

International Nuclear Information System (INIS)

Sealants for radon-resistant foundation construction must seal the gap between concrete sections. Modern sealants have such low permeability that seal performance depends only on the permeability of the material that contacts the sealant. The surface permeability of concrete walls and floors was measured by a specially designed permeameter, which measures the airflow induced by a pressure difference across a temporary test seal applied to the surface. The permeability of bulk concrete is about 10"-"1"5 m"2. Areas free of surface defects had surface permeability ranging from 10"-"1"4 to 10"-"1"6 m"2. However, surface defects are common on concrete wall surfaces, which increase the permeability to >10"-"1"2 m"2, too high for standard seal designs to be adequate as the only method of soil gas and radon exclusion. Radon-resistant seals require either extended ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigates steels 12Kh18N10T, 10Kh17N13M2T, 08Kh22N6T, and 08Kh21N6M2T. In corrosion of stainless steels in sulfuric acid solutions, dissolved sulfur dioxide acts as a cathodic depolarizer, capable of being reduced to elemental sulfur or forming sulfides with the metal. Depending on the conditions, this is associated with some increase in potential and greater or lesser increase in corrosion or facilitation of passivation of active steel. After passivation the influence of SO/sub 2/ is negligible. The results of this investigation were used as initial data for developing systems of anodic protection for shell-and-tube heat exchangers for sulfuric acid.

British Library Electronic Table of Contents (United Kingdom)

Machine-to-machine (M2M) communications is a new and rapidly developing technology for large-scale networking of devices without dependence on human interaction. Energy efficiency is one of the important design objectives for machine-to-machine network architectures that often contain multi-hop wireless subnetworks. Constructing energy-efficient routes for sending data through such networks is important not only for the longevity of the nodes which typically depend on battery energy, but also for achieving an environmentally friendly system design overall, which will be imperative as M2M networks scale in number of nodes as projected. The objective of this survey is to provide a comprehensive look into shortest-path based energy-efficient routing alternatives to provide a reference for sys...

Energy Technology Data Exchange (ETDEWEB)

The authors investigate the corrosion and anodic behavior of steels 12Kh18N10T, 08Kh21N6M2T, and 06KhN28MDT, nickel, and molybdenum in 10-40% naturally aerated solutions of H/sub 2/TiF/sub 6/ at 20 and 50 degrees C. The authors found that in solutions of fluotitanic acid, as also in tetrafluoroboric and hydrofluoric acids, the most stable alloys are chromium-nickel-molybdenum alloy of type 06KhN28MDT and (for acid concentrations above 20%) copper-nickel-alloys of the monel metal type. Steels 12Kh18N10T and 08Kh21N6M2T can be used in acid concentrations of less than 10% and temperatures up to 20 degrees C with anodic protection.

British Library Electronic Table of Contents (United Kingdom)

The association between invasive and native species varies across spatial scales and is affected by phylogenetic relatedness, but these issues have rarely been addressed in aquatic ecosystems. In this study, we used a non-native, highly invasive species of Poaceae (tropical signalgrass) to test the hypotheses that (i) tropical signalgrass success correlates negatively with success of most native species of macrophytes at fine spatial scales, but its success correlates positively or at random with natives at coarse spatial scales, and that (ii) tropical signalgrass is less associated with native species belonging to the family Poaceae than with species belonging to other families (Darwin?s naturalization hypothesis). We used a dataset obtained at fine (0.25?m2) and coarse (ca. 1,000?m2) sca...

International Nuclear Information System (INIS)

A comparative study by Eu-L_I_I_I X-ray absorption and "1"5"1Eu-Moessbauer spectroscopy is presented for the EuPd_2_-_xAu_x Si_2 series. Possible ways to distinguish between mixed-valent behaviour and final-state effects in the L_I_I_I-edge spectra are discussed.

International Nuclear Information System (INIS)

The objective of this paper is to present a theoretical evaluation of soil and house related factors that may affect the transport of radon from the soil into houses. A two-dimensional mathematical model was used to simulate the diffusive and convective transport of radon into the house through idealized openings in the understructure. With the help of model predictions we tried to find out whether diffusion or convection predominates and under which circumstances. Radon transport through cracks in the house understructure is influenced mainly by the soil permeability, radon concentration at the soil-crack interface, the total area of cracks and the pressure difference across cracks. Because of its large range of variability, the soil permeability appears to have the greatest effect on the radon transport through cracks. At permeabilities below 1x10"-"1"2 m"2 diffusive transport predominates and is almost invariable with the soil permeability. ...

Energy Technology Data Exchange (ETDEWEB)

The MiniBooNE Collaboration reports first results of a search for {upsilon}{sub e} appearance in a {upsilon}{sub {mu}} beam. With two largely independent analyses, we observe no significant excess of events above background for reconstructed neutrino energies above 475 MeV. The data are consistent with no oscillations within a two neutrino appearance-only oscillation model.

British Library Electronic Table of Contents (United Kingdom)

We tested the hypothesis that overstorey of eucalypt forest dominated by tall, large diameter trees uses less water than regrowth stands in the high rainfall zone (>1100mmyear^-^1) of the northern jarrah (Eucalyptus marginata) forest in southwestern Australia. We measured leaf area, cover, sapwood area and sapwood density at three paired old and regrowth stands. We also measured sapflow velocity at one paired stand (Dwellingup) from June 2007 to October 2008. Old stands had more basal area but less foliage cover, less leaf area and slightly thinner sapwood. The ratio of sapwood area to basal area decreased markedly as tree size increased. Sapwood area of the regrowth forest stands (6.6+/-0.30m^2ha^-^1) was nearly double that of the old stands (3.4+/-0.17m^2ha^-^1), despite larger basal are...

International Nuclear Information System (INIS)

This paper presents the directional dependence of surface scaling parameters namely roughness length and corresponding friction velocity, for neutral category of Tarapur coastal site. The average roughness length of lowest value of 0.07 m (SW) and the highest value of 0.32 m (E) and average friction velocity of lowest value 1.6 m/sec(SSE) and a highest value 2.8 m/sec (SW) for the year 2006 were observed. Wind profile studies for the coastal site Tarapur with the wind data measured from meteorological tower of 30m which is at 1500m downwind fetch distance from the coastal line in the east direction gave the wind profile index parameter 'p' as 0.4, 0.5 and 0.75 for Unstable, Neutral and Stable weather conditions respectively. Sector Average Turbulent kinetic energy estimated as 17.7m2/s2 and its dissipation rate is 3.1 m2/s3 for the 10m elevation from the surface. A surface drag coefficient CD for the ...

Science.gov (United States)

% In this work we investigated, in the Smooth Particle Hydrodynamics (SPH) framework, the development of spiral structures and shock fronts in the radial flow of accretion discs in close binary systems. These shock waves take place when the initially supersonic radial flow penetrating the disc bulk, reduces substantially its speed becoming suddenly subsonic. To this purpose, keeping constant the mass of the compact primary (M1 = 1 MO ), the separation between the two components and the injection speed at the inner Lagrangian point L1 (close to the local sound speed), we carried out 2D SPH simulations for four values of the stellar mass ratio M2/M1. We worked out 2D models because the damping effect of the artificial viscosity is too strong in 3D. Furthermore, the 2D environment seems the most suitable in order to evidence shock fronts in highly compressible gases. The results show that spiral structures and shock fronts develop for low values ...

International Nuclear Information System (INIS)

From the indoor radon problem arises a great challenge for the radiation protection of the population. The soil can be considered as the only source for high radon concentrations in buildings. The contribution of common building materials to high indoor concentrations with a range of 30 Bq/m"3 is negligible low. Therefore building materials for radon mitigation should be judged by their tightness against diffusive radon and not by their radon exhalation rate. Also isolation materials for mitigation should be radon tight. The radon diffusion coefficient describes the physical processes in relatively homogeneous samples. The diffusion coefficient D and the diffusion length R are very exactly determined by a self engineered measuring method. The range of D reaches from D = (0.0005 to 2.35) . 10"-"6 m"2/s for building materials and from D = (0.07 to < 10"-"6) . 10"-"6 m"2/s for isolation materials. ...

International Nuclear Information System (INIS)

We report the results of neutron-diffraction experiments on CeM_2Si_2 (M = Ag,Au,Pd,Rh) which were performed to explore the role of valence fluctuations and 4f hybridization in the magnetic ordering of cerium compounds. All four order antiferromagnetically, the first three exhibiting structures consisting of ferromagnetic layers with moments perpendicular to the layers, which are believed to be characteristic of 4f-4f interactions mediated through hybridization with conduction electrons. CePd_2Si_2 has an anomalously small moment (0.62#mu#/sub B/) in the ordered state. CeAg_2Si_2 exhibits an incommensurate longitudinal, static magnetization wave with moment and propagation direction along the a axis. The fourth compound, CeRh_2Si_2, has the highest known transition temperature (39 K) reported for cerium ordering; it exhibits another second-order transition at 27 K to a complex commensurate structure with modulated moments. The results are ...

British Library Electronic Table of Contents (United Kingdom)

Porous phosphate heterostructures (PPH), functionalized with different ratios of aminopropyl and mercaptopropyl groups, labelled as Nx=5,25,50-PPH and Sx=5,25,50-PPH, respectively, were tested as adsorbents for Ni(II) and Hg(II) found in industrial sewage from electroplating processes and button battery recycling. X-ray diffraction was used to study the structures. The specific surface area of the pristine material (PPH) was 620m^2g^-^1, whereas the specific surface areas of the modified mercaptopropyl (S5-PPH) and aminopropyl (N5-PPH) were 472 and 223m^2g^-^1, respectively. The adsorption data were fitted to a Langmuir isotherm model. The S5-PPH material was saturated by 120mmol Hg(II) per 100g of material, whereas for Ni(II) adsorption, N25-PPH material displayed the highest adsorption w...

CERN Document Server

We explore as clearly as possible the features of neutrino oscillation which are relevant for measurements of the CP violating Kobayashi-Maskawa phase delta and the sign of \\Delta m^2_{13}. We focus on the so called low-energy option and discuss principles for optimizing experimental parameters to measure these two quantities simultaneously. Toward the goal, we first formulate a method for obtaining a bird-eye view of the phenomenon of neutrino oscillation by introducing a new powerful tool called the ``CP trajectory diagram in bi-probability space''. It allows us to represent pictorially the three effects separately in a single diagram; effect from genuine CP violation due to the sin delta term, effect from the CP conserving cos delta term, and the fake CP violating effect due to earth matter. By using the CP trajectory diagram we observe that there is a two-fold ambiguity in the determination of delta which is related with the sign of Delta ...

DEFF Research Database (Denmark)

The tidal motion of the ocean water through the ambient magnetic field, generates secondary electric field. This motionally induced electric field can be detected in the sea or inland and has a potential for electrical soundings of the Earth. A first goal of the paper is to gain an understanding of the global distribution of the electric signal due to tidal ocean flow. We simulate the electric signals for two tidal constituents - lunar semidiurnal (M2) and diurnal (O1) tides. We assume a realistic Earth's conductivity model with a surface thin shell and 1-D mantle underneath. Simulations demonstrate that in some coastal regions the amplitudes of the electric field can reach 100 mV/km and 10 mV/km for M2 and O1 tides respectively. The changes of lithosphere resistance produce detectable changes in the tidal electric signals. We show that our predictions are in a good agreement with observations.

DEFF Research Database (Denmark)

Purpose Cisplatin plus gemcitabine is a standard regimen for first-line treatment of advanced non-small-cell lung cancer (NSCLC). Phase II studies of pemetrexed plus platinum compounds have also shown activity in this setting. Patients and Methods This noninferiority, phase III, randomized study compared the overall survival between treatment arms using a fixed margin method (hazard ratio [HR] < 1.176) in 1,725 chemotherapy-naive patients with stage IIIB or IV NSCLC and an Eastern Cooperative Oncology Group performance status of 0 to 1. Patients received cisplatin 75 mg/m(2) on day 1 and gemcitabine 1,250 mg/m(2) on days 1 and 8 (n = 863) or cisplatin 75 mg/m(2) and pemetrexed 500 mg/m(2) on day 1 (n = 862) every 3 weeks for up to six cycles. Results Overall survival for cisplatin/pemetrexed was noninferior to ...

International Nuclear Information System (INIS)

The paper presents experimental investigations of main features of plasma surface interaction and energy transfer to the material surface in dependence on plasma heat loads. The experiments were performed with QSPA repetitive plasma pulses of the duration of 0.25 ms and the energy density up to 2.5 MJ/m2. Surface morphology of the targets exposed to QSPA plasma screams is analyzed. Relative contribution of the Lorentz force and plasma pressure gradient to the resulting surface profile is discussed. development of cracking on the tungsten surface and swelling of the surface are found to be in strong dependence on initial temperature of the target.

International Nuclear Information System (INIS)

Within the framework of the EU power plant conceptual study (PPCS), a modular He-cooled divertor concept with integrated pin array (HEMP) is being developed at the Forschungszentrum Karlsruhe. The design goal is to achieve a high heat flux of at least about 10-15 MW/m"2, which is proposed for a near-term reactor model like DEMO. The development and optimization of the divertor concept require a close link between the main issues: design, analyses, materials and fabrication technology, and experiments with feedbacks between them to be accounted for. Design-specific requirements on materials and fabrication issues will be discussed.

Energy Technology Data Exchange (ETDEWEB)

Density oscillations induced by MHD activities were observed in NBI heated plasmas on CHS by using an HCN laser interferometer. The accompanied changes of the density profiles were also observed. The oscillations are composition of m=0 sawteeth like crash and m=2 sinusoidal oscillations as a post courser of the crash. Possible models of the oscillation structure are examined in order to explain experimental data of the interferometer. Rotating plasma core, which is hollow profile and keeps constant elongation of the flux surface can explain amplitude and phase distribution of the sinusoidal oscillation. (author)

Science.gov (United States)

The COsmic ray Research and Education Array (COREA) collaboration has installed an array of six detector stations at two high schools in and near Seoul, Korea for measurement of air-shower events from high-energy cosmic rays. Three stations are installed at each site, where each station consists of four plastic scintillation detectors covering an area of 2m2. In this presentation, we report the currenst status of the COREA project, describing the experimental equipment and measurement of coincident events.

International Nuclear Information System (INIS)

Cylindrical test pieces of concrete are used for measurements of "2"2"2Rn exhalation rates. Except one flat end surface of a test piece, other parts of its exteriority are covered with sealant. Radon atoms can escape only through its end surface from the interior into the outside air. This treatment makes the radon transport in the concrete one dimensional phenomena. The piece is put in an airtight container. Time variations of radon concentrations in the air of the container are measured with a plane multiwire-electrode ionization chamber. From this result, the radon areal exhalation rate is deduced for the piece. Exhalation rates are measured for four pieces with different length. Then, the diffusion coefficient is obtained for radon in the concrete as (5.0 #+-# 1.0) x 10"-"8m"2s"-"1 (a one-block method). A two-block method has been invented to obtain simultaneously values of three parameters: diffusion coefficient, porosity of concrete, and ...

International Nuclear Information System (INIS)

A large matrix of simple alloys and complex commercial type steels was irradiated over a range of fluxes at 60 FC up to a fast fluence of about 3 x 10"2"2 n/m"2. Combined with data in the literature, these results show a negligible effect of flux on irradiation hardening in the range of 2 x 10"1"3 to 5 x 10"1"8 n/m"2-s. This observation lends indirect support to the proposal that the accelerated embrittlement in the High Flux Isotope Reactor surveillance steels was due to an anomalously high level of damage from gamma rays. A weak dependence of hardening on a number of elements, including copper, nickel, phosphorus, molybdenum and manganese, can be described by a simple empirical chemistry factor. Particular combinations of elements resulted in hardening differences of up to about 60% in the complex commercial type steels and up to about 100% in simple model alloys. Direct effects of microstructure ...

International Nuclear Information System (INIS)

Sesame varieties/genotypes showed a good response to radiation with gamma rays and treatments with EMS. In M_1 both gamma rays and EMS influenced germination, seedling height, survival of plants and pollen fertility/sterility, producing deleterious effects on these characters. Compared to black seeded genotypes, white seeded ones are more susceptible to radiation. Both gamma rays and EMS produced various types of morphological variations in M_2 generation. These were dwarf plant mutants, mottled and fleshy leaved mutants (sterile), fasciated stem, flower colour, altered phyllotaxy, early, uniculm, capsule size variations, multiple capsule/leaf axil, seed coat colour variations, indehiscent and semi-indehiscent type mutants. Moreover, studies on quantitative characters including seed yield revealed the induction of mutants in both positive and negative directions for such traits which made a good scope of selection of desirable mutants in ...

International Nuclear Information System (INIS)

This paper reports that at present geothermal energy is utilized in the USSR mostly for district heating, and for industrial and agricultural purposes. The populations of 7 towns have district heating that is supplied by thermal waters. The population supplied totals about 125,000 people. The total area of greenhouses is 850,000 m"2. Electric energy generated at geothermal power stations still remains negligible with the installed capacity of the single Pauzhetka station (Kamchatka) being 11 MW. another station at Mutnovka is currently under construction and is expected to be producing 50 MW by 1992 and 200 MW by 1998. The proven geothermal resources in the USSR provide hope for a significant increase in the utilization of the earth's deep heat in the near future.

British Library Electronic Table of Contents (United Kingdom)

Background: While Borneo's forests are globally recognised for their diverse vegetation many regions remain uncharacterised. Aims: We examine the tree community in one hectare of lowland (hill) forest near the Malinau River. Methods: We objectively sited a 1-ha plot in primary forest. All stems over 30 cm girth were measured and identified. Results: Stem basal area was typical for Asian rain forests, but the numbers of stems (759) and species (205) were high. The most abundant species were Gluta wallichii, Cleistanthus bakonensis and Lithocarpus cantleyanus, while those contributing most to basal area were Shorea venulosa, Dipterocarpus lowii and Calophyllum lowii. Dipterocarpaceae was the dominant family amongst the largest stems and contributes a third of stand basal area (11.5 m2). Thir...

International Nuclear Information System (INIS)

A series of nine model ferritic alloys were ion irradiated at #propor to#300 C using 2.5 MeV He ions to a dose of 1.4 x 10"2"1 ion/m"2, which corresponds to #propor to#0.1 dpa at a depth of 2 #mu#m and #propor to#3.5 dpa at the peak damage region which occurs at about 4 #mu#m deep. The resultant changes in hardness as a function of depth were measured using a Nanoindenter "t"r"a"d"e"m"a"r"k. TEM was used to investigate the defect distributions. The effect of various solutes, Cu and N in particular, but Mn and Ti as well, on the change of hardness and the defect distribution due to the ion irradiation are discussed. (orig.).

International Nuclear Information System (INIS)

The separation of humic substances by polysulfone has been done. Thisinvestigation aims at separating the humic substances contained in theestuary environment. Because of without sample pre-treatment, cheap and easythis method has been to choice. At preliminary study proved that byincreasing the pressure until 50 psia, the yield of flux was 13.5 l/m"2.jamand the reject coefficient was 90.98%, so that polysulfone membrane isappropriate to be applied. More over the pressure could be increased morethan 50 psia. The feed concentration should be lower than 150 ppm, though thevolume should be greater. The pH condition should be alkaline (pH> 7), sinceat this condition the filtration process is easily conducted and the rejectcoefficient could reach 95.09%. (author)

International Nuclear Information System (INIS)

We consider the electron-positron pair creation by a photon in an external constant electric field. The presented treatment is based on a purely quasiclassical calculation of the imaginary part of the on-shell photon polarization operator. By using this approach we find the pair production rate for photons with polarization parallel as well as orthogonal to the external electric field in the leading order in the parameter eE/m"2, which has been recently found by other methods. For the orthogonal polarization we also find a new contribution to the rate, which is leading in the ratio of the photon energy to the electron mass #omega#/m. We also reproduce by a purely geometrical calculation the exponential factor in the probability of the stimulated pair creation at arbitrary energy of the photon.

CERN Document Server

We present a proposal for a combined ICARUS & NOE general purpose detector, to be installed in Hall B of the Gran Sasso Laboratory.The main scientific goal is the one of elucidating in a comprehensive way the pattern of neutrino $9 masses and mixings, following both (1) the S-KAM results and (2) the predictions on atmospheric neutrinos of the large solution of the Solar Neutrinos deficit. To achieve these goals, the experimental method is based upon the $9 complementary and simultaneous detection of CERN beam (CNGS) and cosmic ray (CR) events. This is made possible because of the complete isotropy of the detection technique. For the currently allowed values of the S-KAM results, both $9 CNGS and cosmic ray data will give independent measurements and provide a precise $(sin^{2}2\\theta; \\Delta m^{2})$ determination rather than a wide band of allowed values. Since we can observe and unambiguously identify $9 $\

British Library Electronic Table of Contents (United Kingdom)

A study was conducted to determine the fitting soil moisture for the normal growth of two-year-old W. sinensis (Sims) Sweets by using gas exchange technique. Remarkable threshold values of net photosynthetic rate (Pn), transpiration rate (Tr) and water use efficiency (WUE) were observed in the W. sinensis leaves treated by various soil moisture and photosynthetic available radiation (PAR). The fitting soil moisture for maintaining a high level of Pn and WUE was in range of 15.3%?26.5% of volumetric water content (VWC), of which the optimal VWC was 23.3%. Under the condition of fitting soil moisture, the light saturation point of leaves occurred at above 800?mol?m?2?s?1, whereas under the condition of water deficiency (VWC, 11.9% and 8.2%) or oversaturation (VWC, 26.5%), the light saturatio...

International Nuclear Information System (INIS)

Full text: A method to measure noise power spectrum of a full field digital mammography system is presented. The effect of X-ray radiation dose, size and configuration of region of interest on normalized noise power spectrum (NNPS) was investigated. Flat field images were acquired using RQA-M2 beam quality technique (Mo/Mo anode-filter, 28 kV, 2 mm Al) with different clinical radiation doses. The images were cropped at about 4 cm from the edge of the breast wall and then divided into different size of non-overlapping or overlapping segments. NNPS was determined through de trending, 2-D fast Fourier transformation and normalization. Our measurement shows that high radiation dose gave lower NNPS at a specific beam quality. (author)

British Library Electronic Table of Contents (United Kingdom)

The objective of materials research is the development of economical, safe and efficient synthesis routes that lead to the formation of a photocatalyst which is able to overcome performance problems related to particle size, crystallinity, or low surface area. Here, we report high-quality functional nanoparticles of calcium bismuth mixed oxide with 15nm nominal size corresponding to a specific surface area of 41m^2/g which were produced by single-step flame spray synthesis (FSS). The high temperature of the flame afforded creation of oxygen vacancies which were quantified by near edge X-ray absorption fine structure (NEXAFS) spectra. These two parameters, developed active surface area and created in the flame oxygen vacancies, allowed to enhance the photocatalytic activity of calcium bismu...

British Library Electronic Table of Contents (United Kingdom)

Dissolved microcystins (MCs) are regularly present in water dominated by microcystin-producing, bloom-forming cyanobacteria. In vitro experiments with environmentally feasible concentrations (5 ? 10?7 M) of the three most common microcystins, MC-LR, MC-RR, and MC-YR, revealed that they influence the metabolism of different representative phytoplanktons. At light intensities that are close to the cyanobacterial bloom environment (50??mol m?2 s?1), they produce morphological and physiological changes in both microcystin-producing and -nonproducing Microcystis aeruginosa strains and also have similar effects on the green alga Scenedesmus quadricauda that is frequently present in cyanobacterial blooms. All three microcystin variants tested induce cell aggregation, increase in cell volume, and ...

British Library Electronic Table of Contents (United Kingdom)

Forest restoration efforts should aim at creating landscapes with a balanced array of forest stands at varying successional stages, thus providing habitat for a wealth of species and multiple ecosystem services. In most high-mountain ecosystems of South America, long-term livestock rearing activities that include fires, browsing, and trampling have delayed or stopped forest succession resulting in simplified landscapes. To determine appropriate restoration goals for Polylepis australis mountain forests of Central Argentina, we established 146 plots of 900 m2 plots throughout five river basins with different historic livestock stocking rates. In each plot, we measured tree heights, canopy cover, estimated age of oldest tree, volume of standing and fallen dead wood, fern cover, and abundance...

International Nuclear Information System (INIS)

Intergranular corrosion (IGC) resistance of types 304LN and 316LN stainless steels (SS) thermally aged at 823, 873, and 923 K for various durations was assessed by ASTM A262 practice A test (electrolytic etch test) and electrochemical potentiodynamic reactivation (EPR) test. The results indicated that the type 316LN SS has significantly improved IGC resistance compared to 304LN SS. Based on the results of these tests, time-temperature-sensitization (TTS) diagrams were developed for both alloys. The secondary precipitates formed during thermal aging treatments were electrochemically extracted and analyzed by X-ray diffraction (XRD) to determine the types of precipitates formed during the aging treatments. The results indicated that the precipitates were mostly of M_2_3C_6 carbides.

CERN Document Server

Amplitudes for fermion-fermion, boson-boson and fermion-boson interactions are calculated in the second order of perturbation theory in the Lobachevsky space. An essential ingredient of the model is the Weinberg's 2(2j+1)-component formalism for describing a particle of spin j. The boson-boson amplitude is then compared with the two-fermion amplitude obtained long ago by Skachkov on the basis of the Hamiltonian formulation of quantum field theory on the mass hyperboloid, p_0^2 - p^2=M^2, proposed by Kadyshevsky. The parametrization of the amplitudes by means of the momentum transfer in the Lobachevsky space leads to same spin structures in the expressions of T-matrices for the fermion case and the boson case. However, certain differences are found. Possible physical applications are discussed.

British Library Electronic Table of Contents (United Kingdom)

Purpose In literature, few papers compare different hemostatic devices in laparoscopic adrenalectomy. This sequential cohort study analyzes the outcomes of laparoscopic adrenalectomy performed by different hemostatic instruments, to evaluate if any of them has any advantage over the other and as secondary endpoints, the impact of body mass index (BMI) and tumor size on the indication, and the outcome of laparoscopic adrenalectomy. Methods Forty-six patients, aged 54.6???46?years, underwent laparoscopic adrenalectomy over 5?years. Mean BMI was 27???4.8?kg/m2. Twenty-four patients had a left tumor, and 22 had a right one. Patients were divided into two groups according to the hemostatic device: Ultracision was used in 26 patients, and Ligasure was used in 20. Groups were well matched for his...

International Nuclear Information System (INIS)

Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m"2K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)

British Library Electronic Table of Contents (United Kingdom)

AbstractBACKGROUND: The authors chose to examine the association between body mass index (BMI) and incident colorectal cancer across the spectrum of BMI, including underweight persons, because detailed prospective cohort data on this topic in Asians is scarce, as is data on underweight persons (BMI, <18.5 kg/m2) in any population. METHODS: Analysis of the Singapore Chinese Health Study included 51,251 men and women aged 45-74 years enrolled in 1993-1998 and followed through 2007. Incident cancer cases and deaths among cohort members were identified through record linkage, and 980 cases were identified. Cox regression models were used to investigate the association of baseline BMI with risk of incident colorectal cancer during a mean of 11.5 years of follow-up. RESULTS: A significant, U-sha...

International Nuclear Information System (INIS)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m3 in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m2 in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

International Nuclear Information System (INIS)

Environmental factors, phytoplankton biomass (Chl a) and primary production of two water areas in Daya Bay (Dapeng'ao Bay and Aotou Bay) were investigated during the transition period from spring to summer. Chl a ranged from 3.20 to 13.62 and 13.43 to 26.49 mg m"-"3 in Dapeng'ao Bay and Aotou Bay respectively, if data obtained during red tides are excluded. Primary production varied between 239.7 and 1001.4 mgC m"-"2 d"-"1 in Dapeng'ao Bay. The regional distribution of Chl a and primary production were mostly consistent from spring to summer in both bays. Seasonal transition characters have been found in Daya Bay from spring to summer, including high values of DO, nitrate and silicate. Size structures of phytoplankton and its primary production do not change very much from spring to summer, with micro-phytoplankton dominating and contributing about 50% of the whole. In Daya Bay, phytoplankton is limited by nitrogen in spring, and by phosphate ...

International Nuclear Information System (INIS)

The aim of this study is to clarify the radon behavior in the soil at the waste rock yards of uranium mine. We have developed an apparatus for measuring radon diffusion coefficient in soil under the control of soil temperature. The radon diffusion coefficients changed suddenly around the soil temperature of 0degC. The radon diffusion coefficients in dry soil have little temperature dependency, and were comparable coefficients obtained by empirical formula of Rogers and Nielson. To study the restraint effect of radon exhalation by covering with bentonite on soil, we carried out the measurements and the calculations by using one-dimensional transport model of atmosphere and soil. The decrease of radon exhalation rate was 2.9 Bq m"-"2s"-"1 when soil covered with the bentonite of 5 cm thick. The radon concentrations in snow cover and the radon flux from the snow surface were measured at the waste rock yard in Ningyo-toge Environmental Engineering ...

International Nuclear Information System (INIS)

A processing technique for A-15 compounds which has improved mechanical and superconducting properties has been developed. This technique consists of rapid solidification of the alloy by the chill block spinning machine (CBSM) to form amorphous ribbons and by subsequent annealing crystallizes the stable or metastable fine grain flexible A-15 structure. The CBSM has been modified so that all the processing parameters could be controlled and optimized for each alloy composition. By the improved CBSM it was possible to form amorphous Nb_3Si, Nb_3Ge and Nb_3(AlSi) ribbons with more than 80% reproducible rate. Critical current density measurements are limited by contact resistance. A Cu plating technique was introduced in this research that made the contact resistance three orders of magnitude lower than that obtained by other methods. This plated coating also gave an additional mechanical support to the sample and acted as a shunt for thermal stabilization of the sample. J_c of Nb_3Ge at ...

International Nuclear Information System (INIS)

In order to follow some of the changes induced by ultraviolet-B (UV-B, 280-320 nm) radiation in Phaseolus vulgaris and Brassica napus, experiments were designed to localize sites of changes in leaves and to correlate some of the physiological and biochemical changes with penetration of UV-B radiation. B.napus was exposed to 8.9 kJ m"-"2 day"-"1 biologically effective UV-B radiation (UV-B_B_E). The penetration of UV-B radiation into the leaf was followed using a quartz fibre optic microprobe. Monochromatic radiation at 310 nm was decreased by ca 50 and 34% in the adaxial and abaxial epidermis, respectively, in plants not exposed to UV-B, whereas the radiation was decreased by ca 70 and 42%, respectively, in the same region in UV-treated plants. Polychromatic radiation showed a wavelength dependent change mainly for the collimated radiation. The results correlated with the distribution of phenolic compounds analysed from 40 #mu#m paradermal leaf ...

International Nuclear Information System (INIS)

Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m"2 generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat flux up to 12 ...

International Nuclear Information System (INIS)

Ground source heat pumps (GSHPs), often referred to as geothermal heat pumps (GHPs), offer an attractive option for heating and cooling residential and commercial buildings owing to their higher energy efficiency compared with conventional systems. GSHPs have been used for four years in the Turkish market, although they have been in use for more years in developed countries. The purpose of this study is to present an energy and exergy analysis of a GSHP system with a 50 m vertical 1.25 in. nominal diameter U-bend ground heat exchanger. This system was applied to a 65 m"2 room in the Solar Energy Institute, Ege University, Izmir, for the first time at the university level in Turkey. The Institute, built in 1986, has a livable floor area of 3000 m"2 and uses passive solar techniques. The heating and cooling loads of the room studied were 3.8 and 4.2 kW at design conditions, respectively. The system was ...

International Nuclear Information System (INIS)

The creep characteristics of alloy 800 at temperatures around 600"0C are greatly affected by the composition and treatments in the final stages of manufacture. Short-term and creep properties of alloy 800 at 600"0C are described for six melts covering the carbon range 0.054-0.078%, the titanium range 0.23-0.57% and the aluminium range 0.17-0.52%. The properties are related to the alloy chemistry and the microstructure. It is shown that homogeneously nucleated #gamma#'-precipitates are the main cause of low ductility in alloy 800 but there is also some influence of, for instance, grain boundary M_2_3C_6 films and discontinuous precipitation of Ni_3Ti or M_2_3C_6 in grain boundaries. The extent of #gamma#'-precipitation is controlled primarily by the (Ti+Al)-content. To avoid #gamma#' and ensure a high creep ductility the (Ti+Al)-content should be limited to 0.70-0.75% for alloy 800 with a carbon content ...

International Nuclear Information System (INIS)

Background and purpose: We evaluate the feasibility of concomitant and adjuvant docetaxel combined with three-dimensional conformal radiotherapy (3D-CRT) and androgen deprivation in high-risk prostate carcinomas. Methods: Fifty men with high-risk localized prostate cancer (16), locally advanced (28) or very high-risk prostate cancer (6) were included. Seventy Gy were delivered on prostate and seminal vesicles in 35 fractions, concurrently with weekly docetaxel (20 mg/m"2). Three weeks after the completion of 3D-CRT, docetaxel was given for 3 cycles (60 mg/m"2), every 3 weeks. Patients had to receive LHRH agonist during 3 years. Results: The intent to treat analysis shows that four patients out of 15 stopped prematurely the chemotherapy due to grade 3-4 acute toxicity. In the per protocol analysis, 46 patients completed a full-dose chemoradiation regimen representing 413 cycles: five patients experienced ...

Science.gov (United States)

On the basis of the analysis of chemical components of the natural limestones from different deposits in China, the pore structures of the typical limestones, with the different CaCO3 content, were examined. The reactivity of the limestones was investigated by sulfuric acid titration and gas-liquid absorption methods. The research results showed that the specific surface area of the natural limestones studied in this work was about 1.8 m2/g. It was seen that the pH of the limestone slurry rapidly decreased and then back up when the sulfuric acid was added. The higher the CaCO3 content was, or the smaller the particle size was, the larger the pH back-up rate was, and similarly the faster the SO2 concentration of the reactor outlet increased. The Reactivity of the limestone obtained by the sulfuric acid titration had the same features as that obtained by the gas liquid absorption. Compared with the specific surface area, the CaCO3 content had ...

International Nuclear Information System (INIS)

The molar extinction coefficients at the absorption maximum of the solvated electron spectrum have been evaluated to be 900, 970, and 1000 mol-1?m2 for 1,2-ethanediol (12ED), 1,2-propanediol (12PD), and 1,3-propanediol (13PD), respectively. These values are two-third or three-fourth of the value usually reported in the published report. Picosecond pulse radiolysis studies have aided in depicting the radiolytic yield of the solvated electron in these solvents as a function of time from picosecond to microsecond. The radiolytic yield in these viscous solvents is found to be strongly different from that of the water solution. The temperature dependent absorption spectra of the solvated electron in 12ED, 12PD, and 13PD have been also investigated. In all the three solvents, the optical spectra shift to the red with increasing temperature. While the shape of the spectra does not change in 13PD, a widening on the blue side of the absorption band is ...

British Library Electronic Table of Contents (United Kingdom)

A WO3/TiO2 composite, hollow-sphere photocatalyst with average diameter of 320nm and shell thickness of 50nm was successfully prepared using a template method. UV-vis diffuse reflectance spectra illustrated that the main absorption edges of the WO3/TiO2 hollow spheres were red-shifted compared to the TiO2 hollow spheres, indicating an extension of light absorption into the visible region of the composite photocatalyst. The WO3 and TiO2 phases were confirmed by X-ray diffraction analysis. BET isotherms revealed that the specific surface area and average pore diameter of the hollow spheres were 40.95m^2/g and 19nm, respectively. Photocatalytic experiments indicate that 78% MB was degraded by WO3/TiO2 hollow spheres under visible light within 80min. Under the same conditions, only 24% MB can ...

International Nuclear Information System (INIS)

Radio frequency (RF) plasma nitriding using different input plasma processing powers (250-600 W) improves the surface of titanium by forming hard phases of TiN, Ti_2N, and Ti (N) into the surface. The characteristics of the compound layer have been investigated by optical microscopy, microhardness measurements, and X-ray diffraction. The effect of plasma power on the sample temperature, electron temperature, and plasma density was studied using Langmuir double probe. The measured surface hardness value of the compound layer is 2190 HV 0.1 for treated sample at plasma power 500 W. The compound thickness continuously increases as the plasma power increases. The highest nitriding rate of 5.88 #mu#m"2/s was recorded when the input plasma power was adjusted at 550 W. This high nitriding rate of treated titanium samples is ascribed to the high concentration of active nitrogen species in the plasma atmosphere and the formed microcracks near to the ...

Science.gov (United States)

Some authors have concluded that spiral structures and shocks do not develop if an adiabatic index gamma > 1.16 is adopted in accretion disc modelling, whilst others have claimed that they obtained well defined spirals and shocks adopting a gamma = 1.2 and a M_2/M_1 = 1 stellar mass ratio. In our opinion, it should be possible to develop spiral structures for low compressibility gas accretion discs if the primary component is a black hole. We considered a primary black hole of 8 solar mass and a small secondary component of 0.5 solar mass to favour spiral structures formations and possible spiral shocks via gas compression due to a strong gravitational attraction. We performed two 3D SPH simulations and two 2D SPH simulations and characterized a low compressibility model and a high compressibility model for each couple of simulations. 2D models reveal spiral structures existence. Moreover, spiral shocks are also evident in high ...

International Nuclear Information System (INIS)

The aim of this work is to describe the processes during plasma nitriding of Nb-containing, powder metallurgy prepared (PM) tool steel. PM steel was studied containing 2.5% C, 3.3% Si, 6.2% Cr, 2.2% Mo, 2.6% V, 2.6% Nb and 1.0% W, produced by melt atomization and hot isostatic pressing. The hardened and tempered steel was plasma nitrided at temperatures ranging from 470 to 530 deg. C. The nitriding time was 30-180 min. Optical microscopy, electron microscopy, XRD, EDS, WDS and hardness measurements were used to study the steel's properties, microstructure, phases and chemical composition. The nitriding temperature of 470 deg. C was found to be unsuitable for practical use because the layers prepared at this temperature were non-uniform. The compound layer formed by M_2_,_3(C,N) and M_4N was found after nitriding at temperatures of 500 and 530 deg. C for at least 60 min. The effect of niobium on the formation of this layer was studied.

Science.gov (United States)

We prepared submicron-scale spherical hollow particles of anatase TiO2 by using a polystyrene-bead template. The obtained particles were very uniform in size, with a diameter of 490 nm and a shell thickness of 30 nm. The Brunauer-Emmett-Teller surface area measurements revealed a large value of 70 m2/g. The photocatalytic property was investigated by the complete decomposition of gaseous isopropyl alcohol under UV irradiation. It was indicated that the activity of the hollow spheres was 1.8 times higher than that of the conventional P25 TiO2 nanoparticles with a diameter of 30 nm. Furthermore, we fabricated a dye-sensitized solar cell (DSC) using an electrode of the TiO2 hollow spheres, and examined the photovoltaic performance under simulated sunlight. Although the per-area efficiency was rather low (1.26%) because of a low area density of TiO2 on the electrode, the per-weight efficiency was 2.5 times higher than those of the conventional DSCs ...

International Nuclear Information System (INIS)

There is growing interest in the use of natural fibres as the reinforcements for polymer composites in the automotive industry and as matrix for composites in building products application to replace synthetic fibres. In this respect the aim of this study is to develop an environmental friendly composites for furniture industry based on EFB fibres and sago starch. In this preliminary study, a basic composition and processing of EFB fibres-sago starch composites were established and the properties of the composites were determined. EFB fibre content was varied between 50-80% by weight. The amount of sago starch in liquid form was also varied and final weight percentage of sago starch added into the EFB fibres was adjusted accordingly. The mixtures of EFB fibres and sago starch were blended using Haake Rheomixer. The preliminary results indicate that the impact and flexural strengths increased up to 33.58 J/m"2 and 18.92 Mpa, respectively at 70% ...

CERN Document Server

We investigate strong nonlinear damping effects which occur during high amplitude oscillations of neutron stars, and the gravitational waves they produce. For this, we use a general relativistic nonlinear hydrodynamics code in conjunction with a fixed spacetime (Cowling approximation) and a polytropic equation of state (EOS). Gravitational waves are estimated using the quadrupole formula. Our main interest are $l=m=2$ $f$-modes subject to the CFS (Chandrasekhar, Friedman, Schutz) instability, but we also investigate axisymmetric and quasi-radial modes. We study various models to determine the influence of rotation rate and EOS. We find that axisymmetric oscillations at high amplitudes are predominantly damped by shock formation, while the non-axisymmetric $f$-modes are mainly damped by wave breaking and, for rapidly rotating models, coupling to non-axisymmetric inertial modes. From the observed nonlinear damping, we derive upper limits for the ...

International Nuclear Information System (INIS)

Several configurations of moderating and shielding materials have been designed and measured on the LVR-15 reactor for boron neutron capture therapy (BNCT) purposes. To determine the neutron and gamma ray space-energy distributions in the cylindrical geometry, the two-dimensional code DOT with the coupled neutron-gamma data library DLC-36 was used. The experimental verification of the beam parameters was performed in the LVR-15 reactor thermal column empty space with layers of graphite, aluminium, alumina, lead and bismuth. Attention was paid to establishing techniques and instrumentation for monitoring the neutron and gamma ray dose and beam quality. The thermal and epithermal flux densities were measured by activation foils, the neutron spectrum was determined with a Bonner spectrometer and gamma ray background with a scintillation spectrometer. The distribution of thermal neutrons in the human head phantom was mapped with a small semiconductor detector (Si"6Li). Thermoluminescence ...

Energy Technology Data Exchange (ETDEWEB)

Introduces three designs of development working protection recommended for immediate roof, basic roof and a coal seam of 1.5-2 m, 2.5-4 m and 0.7-1.1 m thickness respectively. The first design of roof control includes a dummy road with breaker props (cutting-off support) and pack, and reinforced concrete props. The second pattern comprises a breaking gate, two rows of cutting-off timber support, up to 10 m long pack and wood chocks. According to the third pattern a breaking road was executed 5.7-6 m away from the face end with breaker props at both its sides. Two rows of pack chocks were added to the dip. Advantages and drawbacks of the three patterns are pointed out. Stress distribution in rock is shown. Position of roof and support before and after roof settling is shown. The cost of the three methods is analyzed. Recommendations useful in application of the method are provided.

Science.gov (United States)

Magnetic particles have become very promising materials for drug delivery. However, preparation of magnetite particles with high surface area, biocompatibility, strong magnetic response, and suitable particle size still remains a major challenge. In this report, magnetite nanocrystal clusters with high surface areas were fabricated through a solvothermal process by introducing ammonium acetate as a porogen and trisodium citrate as a surface modification agent. The porosity, which was controlled by the reactant concentration, has been investigated in detail. The surface area of the nanocrystal clusters was as high as 141?m(2) g(-1) . Ibuprofen, as a model drug, was entrapped into the magnetite carriers. The interfacial interaction between the carboxylic groups on the drug molecules and the carboxylate groups on the carriers enhanced the loading efficiency. Low cytotoxicity in MCF-7 cell and in vitro constant drug release behavior combined with ...

CERN Document Server

Smooth (at least 1/2)-BPS Freund-Rubin backgrounds of eleven-dimensional supergravity of the form AdS_4 x X^7 have been recently classified. Requiring that amount of supersymmetry forces X to be a spherical space form, whence isometric to the quotient of the round 7-sphere by a freely-acting finite subgroup of SO(8). The classification is given in terms of ADE subgroups of the quaternions embedded in SO(8) as the graph of an automorphism. In this paper we extend this classification by dropping the requirement that the background be smooth, so that X is now allowed to be an orbifold of the round 7-sphere. We find that if the background is (more than 1/2)-BPS, then it is automatically smooth in accordance with the homogeneity conjecture, but that there are many half-BPS orbifolds, most of them new. The classification is now given in terms of pairs of ADE subgroups of quaternions fibred over the same finite group. We classify such subgroups and then describe the resulting orbifolds in ...

British Library Electronic Table of Contents (United Kingdom)

A solar-driven 10-ton LiBr/H2O single-effect absorption cooling system has been designed and installed at the School of Renewable Energy Technology (SERT), Phitsanulok, Thailand. Construction took place in 2005, after which this system became fully operational and has been supplying cooling for our main testing buildings air-conditioning. Data on the systems operation were collected during 2006 and analyzed to find the extent to which solar energy replaced conventional energy sources. Here, we present these data and show that the 72m2 evacuated tube solar collector delivered a yearly average solar fraction of 81%, while the remaining 19% of thermal energy required by the chiller was supplied by a LPG-fired backup heating unit. We also show that the economics of this cooling system are domi...

Energy Technology Data Exchange (ETDEWEB)

The D2 antidopaminergic drug Domperidone was evaluated singly and in combination with synthetic adrenocorticoid and an H2 antihistamine for its ability to reduce the acute emetic effects of /sup 60/Co whole-body radiation. Random-source adult male dogs were fasted 12 hours, fed a standard meal, injected 44 minutes later and irradiated 47 minutes after that. Four groups of dogs were radiated after drug injections as follows: saline (Con), domperidone (Dom), cimetidine + thiethylperazine (Cim+Thi), and dexamethasone + domperidone + cimetidine (Dex+Dom+Cim). Drug quantities for dogs represented 10 mg Dom, 10 mg Thi, 20 mg Dex, and 300 mg Cim for an average human (70 ka, 1.8 m2). Subjects were exposed on an up-down schedule to determine the radiation necessary to produce vomiting in 50% (ED50) of each group. Emesis onset times, offset times, and number of episodes were recorded. The ED50 of Dex+Dom+Cim was higher than Con. Dom produced more emetic ...

International Nuclear Information System (INIS)

Nanoporous materials have become indispensable in many fields ranging from photonics, catalysis and semiconductor processing to biosensor infrastructure. Rapid and energy efficient process fabrication of these materials is, however, nontrivial. In this communication, we describe a simple method for the rapid fabrication of these materials from colloidal dispersions of Polymethyl Silsesquioxane nanoparticles. Nanoparticle-polymer composites above the decomposition temperature of the polymer are examined and the entropic gain experienced by the nanoparticles in this rubric is harnessed to fabricate novel highly porous films composed of nanoparticles. Optically smooth, hydrophobic films with low refractive indices (as low as 1.048) and high surface areas (as high as 1325 m2 g-1) have been achieved with this approach. In this communication we address the behavior of such systems that are both temperature and substrate surface energy dependent. The ...

International Nuclear Information System (INIS)

Tensile properties of reduced-activation 10Cr-30Mn austenitic steels with carbon levels from 0.003 to 0.55% were investigated over the temperature range from room temperature to 873 K after neutron irradiation in the Japan Materials Testing Reactor at 573 K to 8.5x10"2"2 n/m"2. Irradiation-induced increase in yield stress increased significantly with carbon concentration up to about 0.1% and it was constant above 0.1% carbon. A high density of dislocation loops with small (below 10 nm) and large (20-30 nm) sizes formed during irradiation. The high density, small loops caused a large irradiation hardening, while the large loops contributed only slightly to irradiation hardening. It was considered that carbon atoms formed the small loops together with irradiation defects. The deformation channeling was observed in the irradiated high carbon steels, 0.11 and 0.55% carbon, but not in the very low carbon steel, 0.003% carbon, after deformation near ...

Energy Technology Data Exchange (ETDEWEB)

In the present study, the type and densities of defects in AlN crystals grown on 6H-SiC seeds by the sublimation-recombination method were assessed. The positions of the defects in AlN were first identified by defect selective etching (DSE) in molten NaOH-KOH at 400 C for 2 minutes. Etching produced pits of three different sizes: 1.77 m, 2.35 m , and 2.86 m. The etch pits were either aligned together forming a sub-grain boundary or randomly distributed. The smaller etch pits were either isolated or associated with larger etch pits. After preparing crosssections of the pits by the focused ion beam (FIB) technique, transmission electron microscopy (TEM) was performed to determine which dislocation type (edge, mixed or screw) produced a specific etch pit sizes. Preliminary TEM bright field and dark field study using different zone axes and diffraction vectors indicates an edge dislocation with a Burgers vector 1/3[1120] is associated with the ...

CERN Document Server

The CMS detector (Compact Muon Solenoid) is under construction at one of the four proton-proton interaction points of the LHC (Large Hadron Collider) at CERN, the European Organization for Nuclear Research (Geneva, Switzerland). The inner tracking system of the CMS experiment consisting of silicon detectors will have a diameter of 2.4 m and a length of 5.4 m representing the largest silicon tracker ever. About 15000 silicon strip modules create an active silicon area of 200 m2 to detect charged particles from proton collisions. They are placed on a rigid carbon fibre structure, providing stability within the working conditions of a 4 T solenoid magnetic field at ?10oC. Knowledge of the position of the silicon detectors at the level of 100 ?m is needed for an efficient pattern recognition of charged particle tracks. Metrology methods are used to survey tracker subdetectors and the integrated Laser Alignment System (LAS) provides absolute ...

International Nuclear Information System (INIS)

Short-lived fission gas release from fuel pellets during irradiation was investigated based on the experimental results of the gas-flow rigs irradiated in the Halden Heavy Water Reactor (HBWR). The release-to-birth (R/B) rates of short-lived fission gas were measured by means of gas-flow measurement during the irradiation experiments. Surface-to-volume (S/V) ratios of fuel pellets and diffusion coefficients of short-lived fission gas release were evaluated from the obtained (R/B) values. The increase of (S/V) ratio agreed well with the point where the fuel temperature exceeded the threshold of 1% fission gas release. This indicates that the interlinkage of fission gas bubbles occurred there. The evaluated diffusion coefficients scattered in the range between 10"-"2"3 and 10"-"1"7 m"2/s, and the effects of fuel type (UO_2 or MOX) were not clearly observed. In addition, it is likely that the restructuring effect of fuel pellet on the diffusion ...

International Nuclear Information System (INIS)

The atomic masses of the alkali-metal isotopes "6Li,"2"3Na,"3"9","4"1K,"8"5","8"7Rb, and "1"3"3Cs have been obtained from measurements of cyclotron frequency ratios of pairs of ions simultaneously trapped in a Penning trap. The results, with one standard deviation uncertainty, are: M("6Li)=6.015 122 887 4(16)u,M("2"3Na)=22.989769 282 8(26)u,M("3"9K)=38.963 706 485 6(52)u,M("4"1K)=40.961 825 257 4(48)u,M("8"5Rb)=84.911 789739(9)u,M("8"7Rb)=86.909 180 535(10)u, and M("1"3"3Cs)=132.905 451 963(13)u. Our mass of "6Li yields an improved neutron separation energy for "7Li of 7251.1014(45) keV.

Science.gov (United States)

A laser pyrolysis technique has been used to produce ultrafine particles of iron carbide with diameters ranging from 2 to 20 nm. Catalysis using iron carbide was investigated in the liquefaction of Wyodak subbituminous coal; yields were determined. A study was carried out to examine the possibility of using an ultrasonic extraction technique as a rapid method of product work-up of samples following pretreatment or liquefaction experiments. A similar study had shown that extraction of coal-derived products by an ultrasonic method was rapid and gave yields and product distributions comparable to those obtained by Soxhlet extraction. On another project, three different types of supported catalysts were used to test activity for the combined water-gas shift hydrogenation of a synthetic donor solvent. The three catalysts tested were: (1) Alumina supported NiMo catalyst-Shell 324m; (2) Bulk hydrous TiO NiMo catalyst; (3) Thin film hydrous TiO ...

International Nuclear Information System (INIS)

An experimental study was carried out to determine the effect of rod-bowing on critical heat flux, using an electrically heated rod cluster. In this experiment, rod-bow was set to occur in the severest subchannel and axially at the middle between the last two spacers, with uniform axial heat flux. The maximum gap between the outer and inner rods was reduced variously to 1.6 mm, 1.00 mm and zero from the nominal value of 2.1 mm. Other experimental conditions were as follows: pressure 7 MPa; mass velocity 640-2600 kg/m"2sec; inlet subcooling 40-560 kJ/kg. Experimental results show only a slight rod-bowing effect, if any, compared with normal spacing, as confirmed by analysis of three-dimensional heat conduction around the rod-bowing area and by the local steam quality deviations calculated by subchannel analyses. (Auth.).

British Library Electronic Table of Contents (United Kingdom)

Summary Purpose BMS-275183 is an oral C-4 methyl carbonate analogue of paclitaxel that has the same mechanism of action, stabilization of tubulin polymerization. The present study was designed to: (i) assess the safety and tolerability of BMS-275183, and (ii) determine a suitable Phase II dose of BMS-275183 when given on a continuous daily schedule to patients with advanced solid tumor(s). Methods This was a multi-institutional, open-label, Phase I, single-arm dose escalation study in which cohorts of eligible patients with advanced malignancies were treated with BMS-275183 orally on a continuous daily schedule. The starting dose level was 6?mg/m2/day administered once daily. Cohorts of 3 patients were treated at each dose level provided no dose-limiting toxicities (DLTs) were observed. Ea...

British Library Electronic Table of Contents (United Kingdom)

Objective The aim of this study was to analyze the clinical results of our adaptive radiation therapy scheme of a two-step intensity-modulated radiotherapy (IMRT) method for nasopharyngeal cancer (NPC) at Kinki University Hospital. Methods Between 2000 and 2007, 35 patients with Stage I-IVB NPC treated by IMRT were included. For all patients, treatment-planning computed tomography was done twice before and during IMRT to a total dose of 60-70 Gy/28-35 fractions (median 68 Gy). Chemotherapy (cisplatin 80 mg/m2/3 weeks x 1-3 courses) was given concurrently with IMRT for 31 patients. Results The 3- and 5-year overall survival rates for the 31 patients treated with concurrent chemotherapy were 88% and 83%, respectively. The 3- and 5-year loco-regional control rates for the 31 patients were 93%...

International Nuclear Information System (INIS)

The thermal environment of a hypothetical large indoor hydrocarbon pool fire is more complex compared to outdoor fires and can be more severe for engulfed objects. In order to analyze potential thermal environments for interim storage of spent fuel casks or low-level radioactive waste packages engulfed in pool fires numerical simulations with the CFD fire code FDS3 were carried out for different storage configurations. In addition, data of indoor pool fire experiments were used to validate the model for this type of application. A series of pool fire experiments under different ventilation conditions and varied pool surface (1 m"2 - 4 m"2) inside a compartment of 3.6 m x 3.6 m x 5.7 m was conducted at iBMB (Institut fuer Baustoffe, Massivbau und Brandschutz) of Braunschweig University of Technology, Germany. The instrumentation included thermocouples, heatflux and pressure gauges, bi-directional flow ...

Energy Technology Data Exchange (ETDEWEB)

In the present work the effect of different surface conditions on plasma nitriding response of AISI M2 high speed steel was investigated. The plasma nitriding of ground and sandblasted samples and drills was performed at temperatures of 400 C and 500 C for two gas mixtures: 5 vol.% N{sub 2} and 76 vol.% N{sub 2} in hydrogen. Surface layers were characterized before and after plasma nitriding concerning the microstructure, roughness, microhardness, chemical composition, phase composition and residual stress states. Machining tests were carried out with drills during which drilling forces and flank wear have been measured. A significant effect of the surface state prior to nitriding on residual stress states and the properties of the nitrided layer and untreated core has been observed. Thinner nitrided layers on ground and sandblasted samples were attributed to high compressive residual stress states and a stress affected diffusion of nitrogen ...

International Nuclear Information System (INIS)

The operation and safety of both fossil-fuel and nuclear power stations depend on adequate cooling of the thermal source involved. This is usually accomplished using liquid coolants that are forced through the high temperature regions by a pumping system; this fluid then transports the thermal energy to another section of the power station. However, fluids that undergo boiling during this process create vapor that can be detrimental, and influence safe operation of other system components. The behavior of this vapor, or void, as it is generated and transported through the system is critical in predicting the operational and safety performance. This study uses two advanced penetrating radiation techniques, Real Time Neutron Radiography (RTNR), and High Speed X-Ray Tomography (HS-XCT), to examine void generation and transport behavior in a flow boiling system. The geometries studied were tube side flow boiling in a cylindrical configuration, and a similar flow channel with an internal ...

Science.gov (United States)

Under different sintering temperatures(340 degrees C, 440 degrees C, 540 degrees C, 640 degrees C), four TiO2 particles were prepared. The crystal types of all four samples were found to possess anatase structures by XRD. It was obtained by N2 experimental adsorption at low temperature (77K) that their surface areas and average pore size were between 79 and 124 m2/g, 56.8 and 254.8 A respectively. The pore structure of TiO2 particles was characterized by scanning electron microscope (SEM). The tests of adsorption dynamics for FGD and the performance of SO2 removal were investigated in a fixed-bed system for different samples. The results show that SG540 sample which made at 540 degrees C sintering temperature had the most quality among the four samples. It can adsorb SO2 of 38.9 mg for one gram SG540 sample. Different operating conditions for SG540 such as adsorption temperature, SO2 concentration in flue gas and the superficial velocity of ...

International Nuclear Information System (INIS)

The French radioactive waste management act of December 30, 1991, included two key provisions. It initiated a major research program with three areas of investigation concerning high-level long-lived radioactive waste management routes, and called for the Government to submit a legislative proposal to Parliament within 15 years (by 2006) specifying the policy guidelines adopted. Considering the sensitive nature of the subject, the questions surrounding the issue of radioactive waste, and the social, economic and environmental concerns for present and future generations, the Government has inaugurated, in 2005, a nationwide public debate on these issues between the submittal of the research reports and the parliamentary discussion of the proposed law. In this context, the CEA has decided to concentrate at Marcoule the expertise and experience acquired in the area of radioactive waste management and to make it available to stakeholders and to the public. A scientific cultural center, ...

International Nuclear Information System (INIS)

Thermal fatigue is one of the key factors governing the lifetime of the divertor plate. Tungsten is a promising candidate to cover the surface of the divertor plate in the design of the international thermonuclear experimental reactor (ITER). The W/Cr-bronze divertor small scale mock-ups were manufactured by hot isostatic pressing (HIPing) technique. Thermal fatigue tests of W/Cr-bronze divertor mock-ups have been carried out by an electron beam facility. The mock-ups were tested under a cyclic surface heat flux of 9 MW m"-"2 for 1000 cycles. The electron beam was loaded on the mock-up surface for 20 s and unloaded for 20 s, alternately. The flow rate of water coolant was 0.1 L s"-"1. The 0.3 mm diameter NiCr-NiSi thermocouples were used to monitor the temperature distribution of the mock-up. It was found that the maximum temperature of the tungsten surface was about 400 degree sign C. The saturated temperature at the joint of tungsten and ...

International Nuclear Information System (INIS)

Eu-#alpha#-SiAlON (Eu_m_/_2Si_1_2_-_m_-_nAl_m_+_nO_nN_1_6_-_n) was synthesized with nominal compositions having small m and n values, by firing the powder mixture of Eu_2Si_5N_8, #alpha#-Si_3N_4, AlN, and Al_2O_3 at 1900 "oC for 6 h under 1 MPa nitrogen atmosphere. The ratio of the oxidation state of Eu"2"+/Eu"3"+ was estimated from the X-ray absorption fine structure (XAFS) measurement. The observed X-ray absorption near edge spectrum (XANES) showed that the Eu ion in Eu-#alpha#-SiAlON was mainly in divalent state but also coexisted with a small amount of Eu in the trivalent state. The crystal structure of Eu-#alpha#-SiAlON was refined by the Rietveld analysis of the X-ray powder diffraction patterns. The lattice constants of the samples increased with increasing m and n values. The excitation band of Eu-#alpha#-SiAlON ranged from the ultraviolet to the visible light region and a broad emission band centered at about 590 nm were observed. The ...

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas containing di-atomic gases, perturb drops ...

International Nuclear Information System (INIS)

"2"7Al and "2"9Si solid-state NMR spectra and X-ray diffraction (XRD) patterns were obtained for #alpha#-SiAlON powders prepared by combustion synthesis, according to which the phase transformation and structure evolution of #alpha#-SiAlON were studied. It was found that in #alpha#-SiAlON "2"9Si chemical shift values (-48 < #delta# _S_i < -47) were close to those in #beta#-Si_3N_4 and #alpha#-Si_3N_4, indicating that Si atoms kept SiN_4 coordination to a large extent in #alpha#-SiAlON despite the presence of O atoms. Dissimilarly, "2"7Al chemical shift values in #alpha#-SiAlON deviated clearly from that corresponding to AlN_4 coordination (#delta# _A_l #approx# 112) and occurred in a range from #delta# _A_l 95.5 to 99.9, which should be assigned to tetrahedral AlO _xN_4_-_x (0 #<=# x #<=# 4) coordination. The broadening effect of AlO _xN_4_-_x peaks was noticed, which was suggested to induced by slight dispersion of #alpha#-SiAlON compositions. "2"7Al resonances assigned to ...

International Nuclear Information System (INIS)

In the present paper, experimental study of forced convection boiling were performed to investigate the post-CHF characteristics of a vertical annular channel with one heated rod and four spacer grids for new refrigerant R-134a. The experiments were conducted under outlet pressure of 11.6, 13, 16 and 20 bar, mass fluxes of 100-600 kg/m2s, and inlet temperatures of 25-51 .deg. C. The parametric trend of the post-CHF data was well consistent with previous studies. The two phase flow regime in tube flow occurring downstream of the CHF has been called post-CHF, dispersed flow, liquid-deficient flow, mist flow and film boiling. This regime is characterized by a continuous vapor phase with discrete liquid drops and a non-wetted heated surface. This regime has a considerable importance in the areas of light water reactor(LWR) accident analysis and other film boiling applications. The post-CHF region occurs by design in heat exchangers operating in the ...

International Nuclear Information System (INIS)

This paper discusses a new type of supramolecular material tris{5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinolato} aluminum(III), Al(SCarq)3, which we synthesized using three 5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinoline as bidentate ligands. The peak photoluminescence in the solid phase appears at 488 nm. In cyclic voltammetric measurement, two oxidation peaks, which were obtained at -5.6 and -5.9 eV, correspond to HOMO sites of carbazoyl and aluminum quinolates, respectively. In the investigation of solid morphological thin film, the flat surface was investigated using an atomic force microscope. The root mean square (rms) and mean roughness (Ra) were respectively measured to be 0.427 and 0.343 nm. For the fabrication of organic light-emitting devices (OLEDs) using spin-coating techniques, the turn-on voltage and maximum luminescence of the optimized electroluminescence device, glass/ITO (20 nm)/PEDOT:PSS (75 ...

International Nuclear Information System (INIS)

In this paper, we study the J/#psi#(#UPSILON#) production in Z boson decay in a color-singlet model (CSM). We calculate the next-to-leading-order (NLO) QCD correction to Z#->#quarkonium+QQ, the dominant contribution in the CSM, with the vector and axial-vector parts in the ZQQ vertex being treated separately. The results show that the vector and axial-vector parts have the same K factor (the ratio of the NLO result to the leading-order result) 1.13 with the renormalization scale #mu#=2m_c and m_c=1.5 GeV, and the K factor falls to 0.918 when applying the Brodsky, Lepage, and Mackenzie (BLM) renormalization scale scheme with obtained #mu#_B_L_M=2.28 GeV and m_c=1.5 GeV. By including the contributions from the next-dominant ones, the photon and gluon fragmentation processes, the branching ratio for Z#->#J/#psi#_p_r_o_m_p_t+X is (7.3-10.0)x10"-"5 with the uncertainty consideration for the renormalization scale and charm quark mass. The ...

International Nuclear Information System (INIS)

In this work, ?-SnS2 thin films have been prepared on glass substrates by the spray pyrolysis technique using an alcohol solution which contains tin chloride (SnCl4) and thiourea (SC(NH2)2) as precursors. The structural study shows that ?-SnS2 thin film prepared using optimal experimental conditions: substrate temperature Ts = 280 deg. C and the concentration ratio of sulfur and tin elements in the spray solution x = [S]/[Sn] = 2.5, crystallizes in the hexagonal phase with a strong (0 0 1) X-ray diffraction line. In the same way, microprobe analyses (EPMA) as well as X-ray photoelectron spectroscopy (XPS) show the presence of undiserable phase of SnO2. From the transmission and reflectance spectra, the band gap energy is 2.65 eV. On the other hand, the photothermal properties of such films have been studied, the thermal conductivity was Kc = 0.85 W m-1 K-1 and the thermal diffusivity was Dc = 14.5 x 10-6 m2 s-1. The analysis of ?-SnS2 thin ...

International Nuclear Information System (INIS)

Dosimetry is evaluated for live-line workers exposed to 50 Hz non-uniform magnetic fields from typical high-voltage transmission lines in the United Kingdom. The configurations involve twin-, triple- and quadruple-conductor transmission line bundles. Scenarios include three worker postures for the twin and triple bundles, and four postures for the quadruple bundle. The postures are selected to simulate worst case scenarios representative of work practices and result in highest values of dosimetric measures in critical organs. Only single-phase bundles are considered, as adjacent bundles of differing phase result only in a small reduction of the dosimetric measures. Reported data include various measures of the electric field and current density induced in tissues, as well as of the current density averaged over 1 cm"2 areas normal to the current flow. A value of this latter quantity of 10 mA m"-"2 is suggested as a threshold for neural tissue ...

Energy Technology Data Exchange (ETDEWEB)

A study by the U.S. Air Force School of Aerospace Medicine, Brooks AFB, Texas, has compared the shelter processing transfer of chemical warfare agent simulant vapor for subjects wearing unwashed and laundered ground-crew chemical defense overgarments. Twice laundered and four times laundered protective garments were included in the assessment. Test subjects, wearing the unwashed and laundered protective garments were initially sprayed with liquid simulant (methyl salicylate) to a target density of 5 g m-2. They were then sequentially processed into and through the USAFSAM Collective Protection Shelter (SCPS-2B) test facility. Immediately upon entry to the Toxic-Free Area, the subjects were confined in individual off gassing booths for 2 h while offgassed simulant vapor concentration in the booths was recorded. The resulting mean maximum vapor concentrations recorded in the booths for subjects who had worn unwashed and laundered overgarments ...

International Nuclear Information System (INIS)

Pitting crevice and intergranular corrosion resistances of titanium-modified low-carbon austenitic stainless steel with a nominal composition of 15% Cr, 15% Ni, 0.24% Ti and 2.5% Mo were found superior to conventional type 316 SS. Potentiodynamic anodic polarization studies in a neutral chloride medium (0.5M NaCl solution) and the immersion studies in boiling solution containing (by wt%) 11% H_2SO_4 + 3% HCl + 1% CuCl_2 + 1% FeCl_3 for 24 h showed higher critical pitting and crevice potentials and lower corrosion rate values respectively. The elemental composition across the pit sites was also determined by EPMA analysis. Sensitization studies carried out by following ASTM A262 practices A and E and electrochemical potentiokinetic reactivation (EPR) tests on this alloy heat treated at 923 K for 1 and 50 h showed a better resistance to intergranular corrosion than that for conventional type 316 SS. From the results available, the most likely reason for the improvement in the localized ...

International Nuclear Information System (INIS)

On the basis of soil losses records during 10 years, three levels of water erosion were established for two soil (Typical Hapludox and Oxic Dystropept) located on high and medium terraces of alluvial flat plain of piedmont in the Eastern Plains in La Libertad Research Center of CORPOICA. Eighteen 3 x 10 m"2 run-off plots were fitted out on a nonrandom arrangement of nine plots by landscape and three soil use and management treatments: zero grazing Brachiaria decumbens pasture for six years, up land rice, soybean and maize rotations for six years and bare soil for 10 years. Soil losses under these treatments allowed to define three degrees of erosion: slight (N_3 moderate (N_2) and severe (N_3) respectively. From each plot soil samples were taken at two depths for physical analyses. infiltration and resistance to cone penetration were measured in the field. Without exception water erosion produced a detrimental effect on soil physical properties ...

Energy Technology Data Exchange (ETDEWEB)

We describe the synthesis and characterization of superparamagnetic iron oxide nanoparticle based heavy metal sorbents with various surface chemistries that demonstrate an excellent affinity for the separation of heavy metals in contaminated water systems (i.e. spiked Columbia river water). The magnetic nanoparticle sorbents are prepared from an easy to synthesize iron oxide precursor, followed by a simple, one-step ligand exchange technique to introduce the organic surface functionality of interest chosen to target either specific or broader classes of heavy metals. Functionalized superparamagnetic nanoparticles are excellent sorbent materials for the extraction of heavy metal contaminants from environmental and clinical samples since they are easily removed from the media once bound to the contaminant by simply applying a magnetic field. These engineered magnetic nanoparticle sorbents have an inherently high active surface area (often > 100 ...

International Nuclear Information System (INIS)

Homologous and heterologous arterial segments were implanted in Fisher rats subcutaneously for the purpose of examining the antibody titer of the recipients' serum after implantation by means of the immune-adherence hemagglutination method. The antibody titer after implantation both of homologous and heterologous grafts decreased to 1/8 by 2.0 million (M) rads irradiation of high voltage cathode rays. The results suggested that high voltage cathode ray irradiation was not enough for heterologous graft to suppress its tissue reaction. Homografts taken from dogs 3 or 6 hours after sacrifice were irradiated with 2.0 M rads and transplanted in canine carotid artery using the technic of end-to-end anastomosis. Angiograms 6 months after operation revealed excellent patency rate in all the grafts of 28 dogs. furthermore, findings of the grafts from 1 week to 5 years after operation on scanning and transmission electron microscopies were evaluated. Clinical application of bypass surgery from ...

International Nuclear Information System (INIS)

An induced mutant, RT-10 (M6 generation) was re-irradiated with 300 Gy of gamma rays. In M2 generation a mutant plant was identified, which characterized with large pods, prominent longitudinal ribbon reticulation and slight constriction. The selected mutant, RT-1010 has the highest pod yield (.3.59 t/fed.vs.2.91 and 2.61 t/fed respectively) and harvest index ( 0.52 vs. 0.42 and 0.45 resp.), the best in fancy pods percentage (57.67 % vs. 38.33 % and 44.17 % resp.), TSMK grade (98.96 % vs. 83.03 % and 84.05 % resp.), the largest pod mass (253.37 g vs . 211.32 g and 222.19 g resp.) and the highest expected oil yield (1370 Kg/fed vs. 895.44 Kg and 868.17 Kg/fed. resp.). With regard to fatty acid compositions, both the selected mutant, RT-1010 and the parental mutant RT-10 have almost a similar high oleic fatty acid (C18:1) percentage (56.35 % and 55.103 % respectively), low linoleic fatty acid (C18:2) percentage (24.20 % and 24.138 % resp.), low ...

International Nuclear Information System (INIS)

Electron beams as a source of directed energy are under study at the Lawrence Livermore National Laboratory (LLNL). An intense 10-kA, 50-MeV, 50-ns full-width half-maximum, pulsed electron beam is generated by the prototype Advanced Test Accelerator (ATA) at the Laboratory's Site 300. Whenever the electron beam is stopped in materials, intense radiation is generated. Estimates based on available data in the literature show that for materials such as lead, photon radiation (x ray, gamma, bremsstrahlung) levels can be as large as 10"4 roentgens per pulse at 1 m in the zero-degree direction (i.e., the electron-beam direction). Neutrons, which are emitted isotropically, are produced at a level of 10"1"3 n/m"2 per pulse. Depending upon the number of pulses and the shielding geometry, the accumulated dose is potentially lethal to personnel and potentially damaging to instrumentation that may be used for diagnostics. To provide shielding for ...

International Nuclear Information System (INIS)

A high resolution Compton telescope has been identified by the Gamma Ray Astronomy Program Working Group (GRAPWG) as the highest priority major mission in gamma ray astrophysics following GLAST. This mission should provide 25-100 times improved sensitivity, relative to CGRO and INTEGRAL, for MeV gamma ray lines. It must have good performance for narrow and broad lines and for discrete and diffuse emissions. Several instrumental approaches are being pursued to achieve these goals. We discuss issues relating to this mission including alternative detector concepts, instrumental configurations, and background reduction techniques. We have pursued the development of position-sensitive solid-state detectors (Ge, Si) for a high spectral resolution Compton telescope mission. A #approx#1 m2 germanium Compton telescope of position-sensitive germanium detectors was the basis for one of the GRAPWG concepts. Preliminary Monte Carlo estimates for the ...

Energy Technology Data Exchange (ETDEWEB)

A number of screening tests were performed to determine ion species that effectively reduce wear rates when implanted in four industrial steels. Ball bearing steel 100Cr6 (AISI 52100) showed a wear rate reduction by a factor of 20 when implanted with carbon dioxide to a dose of 5x10{sup 17} cm{sup -2} with a non-mass-separated ion beam and by a factor of {>=}20 when implanted with 5x10{sup 17} cm{sup -2} oxygen ions. For the ferritic and martensite steels X90CrMoV18 (AISI 440B, unhardened and hardened) also a strong wear reduction after implantation of oxygen ions was found. Co-implantation of aluminum and oxygen also reduces wear rates of X90CrMoV18, of S6-5-2 (AISI M2), and of 100Cr6, respectively. For comparison, thin oxide layers were grown in a low-temperature thermal oxidation process. These experiments also yielded reduced wear rates by a factor of 10. The surfaces were investigated and characterized by XPS, SIMS, TEM, and ...

International Nuclear Information System (INIS)

Decaborane (B_1_0H_1_4) cluster ions were implanted into n-Si(100) substrates to fabricate shallow p"+/n junctions. Implant energies of 2 keV, 5 keV, and 20 keV, equivalent to implant energies of the monomer boron ion of 174 eV, 435 eV, and 1.74 keV, respectively, were used at dosages of 1 X 10"1"2 /cm"2 and 1 X 10"1"3 /cm"2. The implanted samples were then subjected to activation annealing at 800 .deg. C, 900 .deg. C, and 1000 .deg. C for 10 s. By using secondary ion mass spectrometry (SIMS) depth profiles, we determined that the depth of the shallow junction (D_s) at a dosage of 1 X 10"1"3 /cm"2 was in the range 12 nm - 45 nm after annealing at 1000 .deg. C. D_s and transient enhanced diffusion (TED) were greatly reduced at implant energies lower than 5 keV, but thermal diffusion (TD) smoothly decreased. In particular, TED was suppressed in the p"+/n junction implanted at 2 keV and a dosage of 1 X 10"1"3 /cm"2, and the formation of only a 5.6-nm ultra-shallow junction was identified. ...

International Nuclear Information System (INIS)

The responses of ramets of hybrid poplar (Populus spp.) (HP) clones NE388 and NE359, and seedlings of red maple (Acer rubrum, L.) to ambient ozone (O_3) were studied during May-September of 2000 and 2001 under natural forest conditions and differing natural sunlight exposures (sun, partial shade and full shade). Ambient O_3 concentrations at the study site reached hourly peaks of 109 and 98 ppb in 2000 and 2001, respectively. Monthly 12-h average O_3 concentrations ranged from 32.3 to 52.9 ppb. Weekly 12-h average photosynthetically active radiation (PAR) within the sun, partial shade and full shade plots ranged from 200 to 750, 50 to 180, and 25 to 75 #mu#mol m"-"2 s"-"1, respectively. Ambient O_3 exposure induced visible foliar symptoms on HP NE388 and NE359 in both growing seasons, with more severe injury observed on NE388 than on NE359. Slight foliar symptoms were observed on red maple seedlings during the 2001growing season. Percentage of ...

International Nuclear Information System (INIS)

Full text: Many studies have demonstrated significant declines in 24-hour energy expenditure (TEE) measured by whole body calorimetry with either the process of weight loss or the maintenance of reduced body weight. The aims of this study were to determine the effect of weight loss and two weeks of weight maintenance on TEE using ["1"4C]-bicarbonate-urea, Eleven subjects (6 males, 5 females), mean (#+-#SE) age 50 #+-# 3 years, BMI 34.1 #+-# 2.1 kg/m2 and body fat 38.7 #+-# 3% were studied before and after a decrease in body weight of > 8% over a period of 8 weeks, followed by two weeks of weight maintenance. Weight loss was induced using the combination of Modifast and one small meal a day (#approx#3.34 MJ/day). Body composition (DEXA), resting energy expenditure (REE) and the thermic effect of a 2.7 MJ test meal (TEF) were measured in addition to TEE at week 2 and again at week 12. Diet was assessed using diaries and physical activity ...

International Nuclear Information System (INIS)

In 1999, the plasma parameters of reversed shear (RS) plasmas had been extended in 1) DT-equivalent fusion power gain Q_D_T"e"q - 0.5 (n_D(0)#tau#_ET_i(0) - 4x10"2"0 m"-"3#centre dot#keV#centre dot#s) for 0.8 s and 2) full non-inductive current drive with 80% of the bootstrap current fraction. Physics of the internal transport barriers (ITBs) in RS plasmas, including the energy transport and the formation of ITB, were extensively studied. A nearly full current drive (92% non-inductively) was obtained with negative ion based neutral beam (NNB) injection (360 keV, 3.4 MW) in a high #beta#_p H-mode plasma (I_p=1.5 MA, B_T=3.7 T, q_9_5=4.2) with high plasma performance (#beta#_N=2.4 and H_8_9=2.56). Rise in the central electron temperature (T_e - 9 keV) resulted in the current drive efficiency #eta#_C_D of NNB reached 1.3x10"1"9 A/W/m"2, the highest for the neutral beam current drive. As for the H-mode plasmas, decrease in the pedestal ion ...

International Nuclear Information System (INIS)

For the advanced fusion reactor FFHR2 (Force Free Helical Reactor) that has been proposed by NIFS, molten salt Flibe (LiF:BeF2=64:36) breeder blanket system is selected because of Flibe's features such as chemical stability, low-pressure operation and low electric conductivity. The Flibe is however high Prandtl number fluid since it has high viscosity and low thermal conductivity. Therefore its heat transfer performance is low compared with liquid Li or Pb-Li. In addition to heat removal of 1MW/m2 on the first wall, electrolysis of molten salt due to MHD effect will take place under high flow rate condition. This indicates that heat transfer enhancement under low flow rate is essential for the Flibe blanket system. In our laboratory, heat transfer characteristics of molten salt HTS (KNO3:NaNO2:NaNO3=53:40:7), have been evaluated, which is used as a simulant fluid of Flibe from the points of view of Be's toxicity and similar Prandtl number. In ...