WorldWideScience
1

Factors Affecting the Environmental Stability of Laminates,  

Science.gov (United States)

... The moisture content-dimension relationship of two laminate components, phenolic core and melamine overlay, are compared. (Author, modified). ...

1967-02-08

2

Core preservation with a laminated, heat-sealed package  

Energy Technology Data Exchange (ETDEWEB)

A core preservation package was developed to maintain the reservoir characteristics of core samples and consequently to improve the quality of data obtained through laboratory core analyses. The package is a heat-sealable plastic-aluminum laminate similar to those common in the food-packaging industry. The laminated core preservation package acts as an impermeable barrier to water vapor and gases, and is resistant to chemical alteration and degradation by core fluids. These performance characteristics result in effective core preservation by maintaining the fluid content of the core. Other advantages of the laminated package are that it is fast and simple to use and eliminates the cumbersome dip-coat step used in some core preservation methods.

1988-12-01

3

Depositional setting of the Upper Jurassic Hith Anhydrite of the Arabian Gulf: An analog to holocene evaporites of the United Arab Emirates and Lake MacLeod of Western Australia  

Energy Technology Data Exchange (ETDEWEB)

The Upper Jurassic Hith Anhydrite is a major hydrocarbon seal in the Arabian Gulf region. Outcrops, core samples from the subsurface, and the literature indicate that the Hith Formation is composed mainly of anhydrite. In most locations where a section of the Hith Formation has been measured, this unit contains less than 20% carbonate much of which is in the form of thin laminations. This lack of carbonate, locally thick layers of salt, and the predominance of anhydrite favor a playa for the setting in which this sediment was accumulated. In fact, much of the Hith has the sedimentary characteristics of the Holocene Lake MacLeod playa of Western Australia, which is dominated by layers of gypsum and halite (what little carbonate that occurs is found in layers at the base of the section). Locally the Hith appears to have accumulated in a sabkha setting, particularly toward central Abu Dhabi where it pinches out into ...

1994-07-01

4

Supersonic flutter of composite sandwich panels  

Science.gov (United States)

A flutter-motion equation is presently derived for a 2D composite sandwich panel considering the total lateral displacement of the plate as the sum of the displacement due to bending of the plate, and that which is due to shear deformation at the core. The effects of core thickness and stacking sequence of the faces on the flutter boundary of the plate are discussed; it is shown that the sandwich panel greatly improves the flutter boundary over that of a composite laminate panel, provided it has sufficient core thickness.

1992-12-01

5

USGS Fact Sheet 040-02  

Science.gov (United States)

and streambed sediment samples 2-6. Graphs showing: 2. Cesium-137 profile in HOE core 3. PAH trends in Lake Houston cores 4. DDE trends in Lake Houston cores 5. Trends in six trace...

2011-08-27

6

Geochemical fingerprints by activation analysis of tephra layers in Lake Van sediments, Turkey  

International Nuclear Information System (INIS)

We discuss geochemical and sedimentological characteristics of 12 tephra layers, intercalated within the finely laminated sediments of Lake Van. Within the about 15 kyr long sediment record studied, volcanic activity concentrated in the periods 2.6-7.2 and 11.9-12.9 kyr B.P. Concentrations of 25 elements provide the geochemical fingerprint of each tephra layer and allow comparison to literature values of potential source volcanoes such as Mts. Nemrut and Suephan. The youngest two tephra layers (and probably also the other three ashes from the 2.6-7.2 kyr B.P. eruptions) originate from the Nemrut volcano. The source of the older tephra (11.9-12.9 kyr B.P.), however, remains unidentified.

2011-07-01

7

Assessment of the historical trace metal contamination of sediments in the Elizabeth River, Virginia  

International Nuclear Information System (INIS)

Two sediment cores (Southern Branch, PC-1, and Western Branch, WB-2) were taken from the highly industrialized Elizabeth River, Virginia. The concentrations of trace metals cadmium, cobalt, chromium, copper, nickel, lead and zinc, major elements iron, manganese and aluminum, organic carbon content and the specific surface area of the sediments were determined in each of the cores. Down-core variations in metals varied significantly in each core with maximum contamination events occurring at different times in different portions of the river. In PC-1, maximum metal concentrations were seen after the appearance of "1"3"7Cs. In contrast, the highest levels in WB-2 occurred well before the appearance of "1"3"7Cs. Although stricter environmental regulations have caused a decrease in metal concentrations since the 1980s, the concentrations in the surface ...

2007-04-01

8

Seismic stratigraphy in the South Cretan fault valley system: A comparison with the upper Quaternary gravitative sedimentation of the region  

Energy Technology Data Exchange (ETDEWEB)

A synthesis of the sedimentation processes as deduced from the seismic stratigraphy and the deduced facies associations suggests the following. Small fans developed along the northern major fault line of the SCFVS and contains sediment fed directly from Crete through a series of small canyons, most of which trend perpendicular to the coast. However, the main east-west-trending valley transects the mid- and lower fan sectors and contains several intravalley basinal areas, converging toward the main Messara basin. Thus much of the suprafan sediment is reworked and longitudinally transported into the deeper basins. In these deeper intrabasinal and main basinal areas the thickness of the post-Messinian sediments generally exceeds 800 m and in places exceeds 1,500 m. Toward the south the SCFVS receives additional sediment from the Ptolemy Mountains and the Gavdos rise. ...

1988-08-01

9

Implications of abrupt climate change.  

UK PubMed Central (United Kingdom)

Records of past climates contained in ice cores, ocean sediments, and other archives show that large, abrupt, widespread climate changes have occurred repeatedly in the past. These changes were especially...Full Text Available

2004-01-01

10

Characterization of an Irish Sea radioactively contaminated marine sediment core by radiometric and mass spectrometric techniques  

International Nuclear Information System (INIS)

A radioactively contaminated marine sediment core stemming from Irish Sea has been characterized by radiometric and mass spectrometric techniques as for "2"3"7Np, "2"4"1Am, "2"3"9Pu, "2"4"0Pu, "2"4"1Pu, "1"3"7Cs and "1"5"4Eu. The data obtained with independent methods in the framework of a QA/QC program as compared with the source term discharges, as well as with those reported in literature, are in good agreement. (author)

2005-02-01

11

Wrapped Laminated Felted Monolithic Combustible Cartridge ...  

Science.gov (United States)

... ordnance requirements. Descriptors : *Combustible cartridge cases, *Patents, Laminates, Felts, Flame inhibitors, Films. Subject ...

1975-08-26

12

The behavior of bonded doubler splices for composite sandwich panels  

Science.gov (United States)

The results of an investigation into the behavior of adhesively bonded doubler splices of two composite material sandwich panels are presented. The splices are studied from three approaches: analytical; numerical (finite elements); and experimental. Several parameters that characterize the splice are developed to determine their influence upon joint strength. These parameters are: doubler overlap length; core stiffness; laminate bending stiffness; the size of the gap between the spliced sandwich panels; and room and elevated temperatures. Similarities and contrasts between these splices and the physically similar single and double lap joints are discussed. The results of this investigation suggest several possible approaches to improving the strength of the sandwich splices.

1980-07-01

13

Historical trends in the accumulation of chemicals in Puget Sound sediment  

International Nuclear Information System (INIS)

As human activity in and around Puget Sound increased, so did the contaminant levels in the sediment. Sediment cores collected in 1 982 revealed inputs of chemicals to the Sound, including lead (Pb), mercury (Hg), silver (Ag), copper (Cu) and petroleum hydrocarbons, began to increase above background in the late 1800s and peaked between 1945 and 1965. Synthetic organic compounds, such as polychlorinated biphenyls (PCBs) and DDT, first appeared in sediments deposited in the 1930s and reached a maximum in the 1960s. The presence of the subsurface maximum concentrations suggests that pollution-control strategies have improved the sediment quality of central Puget Sound. Additional sediment coring was performed in 1991 and samples were collected at six locations in the main basin of Puget Sound. Sediment ages were determined ...

1995-11-05

14

Evidence of minimal methanogenic numbers and activity in sediments collected from the JAPEX/JNOC/GSC et al. Mallik 5L-38 gas hydrate production research well  

Energy Technology Data Exchange (ETDEWEB)

Gene analysis was used to determined the presence, abundance and phylogenetic affiliation of methanogens that exist in gas-hydrate-bearing sediment samples obtained from 23 drill cores from the JAPEX/JNOC/GSC et al. Mallik 5L-38 gas hydrate research well. Rates of methane production were examined using sediment-inoculated enrichments containing {sup 14}C-labeled carbon substrates, carbon dioxide and acetate. Archaeal 16S rDNA was only detected in 6 of the samples, resulting in 8 sequences with relationships to the Miscellaneous Crenarchaeotic Group (7 clones) and the Subsurface Euryarchaeotic Group (1 clone). The single Euryarchaeota sequence did not appear to be related to methanogens. Subsamples from the cores showed variable results upon DNA extraction and amplification. Methanogenic Coenzyme M (CoM) was detected in 13 of the 20 cores, but methanogenic methyl CoM reductase genes ...

2005-07-01

15

Chemometric source identification of PCDD/Fs and other POPs in sediment cores of North-East Germany  

Energy Technology Data Exchange (ETDEWEB)

A broad range of persistent organic pollutants (POPs) and selected heavy metals has been analysed in sediment cores of North-East Germany. The pollutants analysed include polychlorinated dioxins and furans (PCDD/Fs), polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), several pesticides (DDT, HCH, CBz) and its metabolites as well as selected heavy metals. The sediment cores were sampled at five locations, reflecting a range of anthropogenic influences and background contamination: Arkona Basin (AK) representing a remote marine site, Lake Bugsin (BS) a background location only with atmospheric deposition, Lake Quenz (QS) close to the industrial city of Brandenburg, Teltowkanal (TK) in the suburban-industrial zone of Berlin and Lake White (WS) in the centre of Berlin. The age of the lower part of the AK, BS and TK cores were dated at 100-150 years. Results of ...

2004-09-15

16

Magnetic and chemical changes in marine sediments  

Energy Technology Data Exchange (ETDEWEB)

A considerable amount of chemical knowledge of marine sediments has been acquired in recent years but has not yet been utilized by paleomagnetists. On the other hand, geochemists are often unaware of the usefulness of numerous magnetic techniques. In this review we try to bridge this gap, and in particular, we outline many of the chemical and magnetic principles that should allow paleomagnetists to better identify and undertand chemical changes that affect the magnetic properties of marine sediments. The chemical principles include those for distinguishing the four major sources of sediments (continental, biological, authigenic/hydrogenous, volcanic/hydrothermal) from one another by determining elemental abundance distributions, as well as for investigating the stabilities of mineral phases relative to changes in pE and pH. The magnetic principles include the effects of authigenesis and diagenesis on magnetic properties, ...

1980-05-01

17

Curium isotopes and americium-242 m in Irish Sea sediment  

Energy Technology Data Exchange (ETDEWEB)

An intertidal estuarine sediment core was collected from Esk Estuary in the Irish Sea which had been contaminated by low-level radioactive liquid effluent from the nuclear fuel reprocessing plants at Sellafield, UK. The {sup 242}Cm and {sup 243,244}Cm radioactivity concentrations were determined to establish the present contamination levels compared with other radionuclides {sup 137}Cs, {sup 237}Np, {sup 238}Pu, {sup 239,240}Pu, {sup 241}Pu and {sup 241}Am. The results showed that {sup 242}Cm and {sup 244}Cm existed in the detectable levels in the Irish Sea sediment and the concentration of {sup 242m}Am was evaluated from that of {sup 242}Cm. The {sup 242m}Am/{sup 239,240}Pu and {sup 244}Cm/{sup 239,240}Pu inventory ratios in the sediment core were about 0.04% and 0.3%, respectively. The total amount of {sup 242m}Am discharged into the Irish Sea from the start of the operation of ...

1999-03-01

18

The history of the coastal zones of the Great Caribbean tell through their sediments; La historia de las zonas costeras del Gran Caribe contada a traves de sus sedimentos  

Energy Technology Data Exchange (ETDEWEB)

The pollution of the aquatic zones grows with the time, principally due to industrial and urban settlements, among others, in the surroundings of these sites. The sources of this pollution can be identified by the study of the characteristics of the sediment, this gives relevant information to evaluate any aquatic system. Once the sediment is obtained, a series of preliminary tests are carry out (loss of ignition, 210{sup P}b dating) to be sure that we have a sedimentary core that hans .t be mixed, once this has be done we determine radionuclides, heavy metals and organic compounds. (Author) 2 refs.

2008-07-01

19

Application of chloropicrin to Douglas-fir stumps to control laminated ...  

Science.gov (United States)

Sep 1, 2011 ... Title: Application of chloropicrin to Douglas-fir stumps to control laminated root rot does not affect infection or growth of regeneration 16 growing ...

20

High resolution sequence stratigraphy of Miocene deep-water clastic outcrops, Taranaki coast, New Zealand  

Energy Technology Data Exchange (ETDEWEB)

Approximately 700m of deep water clastic deposits of Mt. Messenger Formation are superbly exposed along the Taranaki coast of North Island, New Zealand. Biostratigraphy indicates the interval was deposited during the time span 10.5-9.2m.y. in water depths grading upward from lower bathyal to middle-upper bathyal. This interval is considered part of a 3rd order depositional sequence deposited under conditions of fluctuating relative sea-level, concomitant with high sedimentation rates. Several 4th order depositional sequences, reflecting successive sea-level falls, are recognized within the interval. Sequence boundaries display a range of erosive morphologies from metre-wide canyons to scours several hundred metres across. All components of a generic lowstand systems tract--basin floor fan, channel-levee complex and progading complex--are present in logical and temporal order. They are repetitive through the interval, with the relatively shallower-water components ...

1995-08-01

21

Duplex Combustible Cartridge Case.  

Science.gov (United States)

... projectile. Descriptors : *Combustible cartridge cases, *Patents, Laminates, Ammunition propellants, Nitrocellulose. Subject ...

1974-07-16

22

Ecological evaluation of proposed dredged material from Richmond Harbor Deepening Project and the intensive study of the Turning Basin  

Energy Technology Data Exchange (ETDEWEB)

Richmond Harbor is on the eastern shoreline of central San Francisco Bay and its access channels and several of the shipping berths are no longer wide or deep enough to accommodate modem deeper-draft vessels. The Water Resources Development Act of 1986 (PL99-662) authorized the US Army Corps of Engineers (USACE), San Francisco District to deepen and widen the navigation channels in Richmond Harbor. Several options for disposal of the material from this dredging project are under consideration by USACE: disposal within San Francisco Bay, at open-ocean disposal sites, or at uplands disposal sites. Purpose of this study was to conduct comprehensive evaluations, including chemical, biological, and bioaccumulation testing of sediments in selected areas of Richmond Harbor. This information was required by the Environmental Protection Agency (EPA) and USACE. Battelle/Marine Sciences Laboratory collected 20 core samples, both 4-in. and 12-in., to a ...

1995-06-01

23

Thermal Cycling of Thin and Thick Ply Composites  

Energy Technology Data Exchange (ETDEWEB)

An experimental study was conducted to determine the effects of ply thickness in composite laminates on thermally induced cracking and changes in the coefficient of thermal expansion (CTE). After a few thermal cycles, laminates with thick-plies cracked, resulting in large changes in CTE. CTE`s of the thin-ply laminates were unaffected by microcracking during the first 500 thermal cycles, whereas, the CTE`s of the thick-ply laminates changed significantly. After about 1500 cycles, microdamage had also reduced the CTE of the thin-ply laminates to a value of about half of their initial value.

1994-01-01

24

Extrinsic fracture mechanisms in two laminated metal composites  

Energy Technology Data Exchange (ETDEWEB)

The crack growth behavior and fracture toughness of two laminated metal composites (6090/SiC/25p laminated with 5182 and ultrahigh-carbon steel laminated with brass) have been studied in both ``crack arrester`` and ``crack divider`` orientations. The mechanisms of crack growth were analyzed and extrinsic toughening mechanisms were found to contribute significantly to the toughness. The influence of laminate architecture (layer thickness and component volume function), component material properties and residual stress on these mechanisms and the resulting crack growth resistance are discussed.

1994-11-29

25

Use of thin glass reflectors for solar concentrators  

Science.gov (United States)

Elastically deforming thin glass (thickness = 0.13 to 0.80 mm) provides an alternate method of forming a curved glass reflector which can eliminate some of the disadvantages of thicker glass. A concept is described where silvered thin glass is bonded to a steel backing to form a laminate with a reflectance greater than 93%. Subsequent bending of the flat reflector laminate to a concentrating profile produces compressive stresses throughout the glass if the laminate is properly designed. These compressive stresses enhance fracture resistance and the lamination provides protection for the silver. The design of the laminate is outlined for 0.25 and 0.51 mm thickness glass and fabrication procedures are discussed. Thermal/humidity cycling, hail impact, bond strength measurements and reflectance results are presented which demonstrate the performance capabilities of this reflector ...

1980-01-01

26

Curium isotopes and americium-242 m in Irish Sea sediment  

International Nuclear Information System (INIS)

An intertidal estuarine sediment core was collected from Esk Estuary in the Irish Sea which had been contaminated by low-level radioactive liquid effluent from the nuclear fuel reprocessing plants at Sellafield, UK. The "2"4"2Cm and "2"4"3","2"4"4Cm radioactivity concentrations were determined to establish the present contamination levels compared with other radionuclides "1"3"7Cs, "2"3"7Np, "2"3"8Pu, "2"3"9","2"4"0Pu, "2"4"1Pu and "2"4"1Am. The results showed that "2"4"2Cm and "2"4"4Cm existed in the detectable levels in the Irish Sea sediment and the concentration of "2"4"2"mAm was evaluated from that of "2"4"2Cm. The "2"4"2"mAm/"2"3"9","2"4"0Pu and "2"4"4Cm/"2"3"9","2"4"0Pu inventory ratios in the sediment core were about 0.04% and 0.3%, respectively. The total amount of "2"4"2"mAm discharged into the Irish Sea from the start of the operation of BNFL Sellafield in 1952 to 1988 ...

27

Study on high-resolution sequence stratigraphy framework of uranium-hosting rock series in Qianjiadian sag  

International Nuclear Information System (INIS)

The ore-hosting Yaojia Formation is composed of a set of braided stream medium-fine grained sediments. Guided by the basic theory of high-resolution sequence stratigraphy, and based on the core observation, the analysis of chemical composition of rocks, and data of natural potential logging and apparent resistivity logging, the authors have set up the high-resolution sequence stratigraphy framework of the ore-hosting Yaojia Formation, and discussed the relation of the stratigraphic structure of the middle cycle, as well as the paleotopography, the micro-facies to the formation of uranium deposit. (authors)

2005-07-01

28

SRP Baseline Hydrogeologic Investigation, Phase 3  

Energy Technology Data Exchange (ETDEWEB)

The SRP Baseline Hydrogeologic Investigation was implemented for the purpose of updating and improving the knowledge and understanding of the hydrogeologic systems underlying the SRP site. Phase III, which is discussed in this report, includes the drilling of 7 deep coreholes (sites P-24 through P-30) and the installation of 53 observation wells ranging in depth from approximately 50 ft to more than 970 ft below the ground surface. In addition to the collection of geologic cores for lithologic and stratigraphic study, samples were also collected for the determination of physical characteristics of the sediments and for the identification of microorganisms.

1988-08-01

29

Radioactivity in sediments of the Great Lakes: post-depositional redistribution by deposit-feeding organisms  

International Nuclear Information System (INIS)

At two locations in southern Lake Huron (U.S.A.), twelve 35.5-cm diameter cores of fine-grained sediments were taken for comparison of the vertical distribution of "2"1"0Pb and fallout "1"3"7Cs with the distribution of benthic macroinvertebrates, mainly oligochaete worms (Tubificidae) and the amphipod, Pontoporeia affinis. Locations were selected on the basis of "2"1"0Pb distributions measured a year earlier which indicated contrasting depths of mixing of surface sediments. At one location the activity of "2"1"0Pb is uniform down to about 6 cm and 95% of total invertebrates occur within this zone; at the other location the zone of constant activity is only 3 cm deep but 90% of the invertebrates occur within it. Comparison of published tubificid defecation rates with sediment accumulation rates based on "2"1"0Pb shows that oligochaetes alone can account for mixing in one case while the effects of ...

30

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

Energy Technology Data Exchange (ETDEWEB)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a {sup 137}Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 {+-} 0.9 cm{sup 2} y{sup -1}, is in good agreement with the values quoted by other workers on the ...

2010-11-15

31

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

International Nuclear Information System (INIS)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a "1"3"7Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 #+-# 0.9 cm"2 y"-"1, is in good agreement with the values quoted by other workers on the bioturbation ...

2010-11-01

32

Quantities and types of ceramides and their relationships to physical properties of the horn covering the claws of clinically normal cows and cows with subclinical laminitis  

UK PubMed Central (United Kingdom)

AbstractQuantities and types of ceramides and their relationships to physical properties of the horn covering the claws of clinically normal cows and cows with subclinical laminitis were...Full Text Available

2005-04-01

33

Effect of Heat Treatment on Some Mechanical Properties of Laminated Window Profiles Manufactured Using Two Types of Adhesives  

UK PubMed Central (United Kingdom)

The mechanical properties of laminated window profiles manufactured using two types of adhesives were determined. The objective of this study is to evaluate the effects of heat treatment on some mechanical...Full Text Available

34

The Effect of Compressive Loading on the Fatigue Lifetime of ...  

Science.gov (United States)

... Coupon 119 * 52 Probability of Survival Versus Ultimate Compressive Strength for Un-notched Laminate 1 Coupon ipn ...

1979-10-01

35

Damage and Repair of the APS Graphite/Epoxy Composite ...  

Science.gov (United States)

... Abstract : High temperature testing of graphite/epoxy laminates and composite sandwich panels was performed while the Shuttle was on orbit to ...

1982-10-12

36

The static indentation behavior of composite sandwich panels with thin quasi-isotropic skins  

Science.gov (United States)

The quasi-static normal indentation of sandwich panels with quasi-isotropic laminated composite skins and honeycomb or foam cores, by spherical indentors, has been investigated using experiments and finite element analysis. The experimental program emphasized the effects of indentor size on the resulting load indentation responses, failure mechanisms in the skin and the core, and the measurement of contact areas between indentor and the target. The sandwich panels were indented up to the initiation of skin fracture and the resulting contact data was used to characterize contact power laws. A non-linear finite element model was developed based on the experimental observations to systematically explore the indentation behavior of diverse sandwich configurations and to investigate the contact pressure distributions. The finite element model was used as an experimental tool in the development of a simple non-dimensional ...

2001-01-01

37

Effect of heat treatment on the properties of Metglas foils, and laminated magnetoelectric composites made thereof  

British Library Electronic Table of Contents (United Kingdom)

Annealing of magnetostrictive Metglas foils, subsequently incorporated into laminated Metglas/Pb(Zr, Ti)O3 magnetoelectric (ME) composites, is shown to result in improved magnetic properties, as well as ME coefficients. Annealing of the foils at 350 ?C resulted in partial crystallization, without oxidation or magnetic cluster formation that would reduce the magnetization. Laminate composites made with these annealed Metglas foils had improved ME coefficients.

2011-01-01

38

Effect of planktivores, zooplankton, and macrobenthos on material flow in a small lake  

International Nuclear Information System (INIS)

Planktivores, zooplankton grazers, and macrobenthos were studied to determine how changes in animal community structure may alter the flow of material in Dunham Pond, CT. Chaoborus and chironomid larvae were studied to determine how they affect the flux of matter across the sediment/water interface. This was done by incubating undisturbed cores in situ and relating changes in water chemistry to larval density. The log-transformed flux rates of iron, manganese, and phosphorus were linearly related to larval biomass. Functional groups may be successfully used to predict rates of material flow. Changes in the mass of macroinvertebrates affect the flux rates of redox-active substances across the sediment/water interface. The use of population densities and feeding characteristics to estimate trophic transfer in Dunham Pond indicate that (1) visual planktivory by larval perch may result in overutilization of prey, (2) ambush ...

39

Influence of solar activity and environment on 10Be in recent natural archives  

Energy Technology Data Exchange (ETDEWEB)

Understanding the link between the Sun and climate is vital in the current incidence of global climate change, and 10Be in natural archives constitutes an excellent tracer for this purpose. As cosmic rays enter the atmosphere, cosmogenic isotopes like 10Be and 14C are formed. Variations in solar activity modulate the amount of incoming cosmic rays, and thereby cosmogenic isotope production. Atmospherically produced 10Be enters natural archives such as sediments and glaciers by wet and dry deposition within about a year of production. 10Be from natural archives therefore provides information on past solar activity, and because these archives also contain climate information, solar activity and climate can be linked. One remaining question is to what degree 10Be in natural archives reflects production, and to what extent the local and regional environment overprints the production signal. To explore this, 10Be was measured at annual resolution over the last 600 years ...

2009-05-15

40

Hydrogeologic investigations related to seepage and instability phenomena within and adjacent the earth structures at Grand Rapids Generating Station, Manitoba  

Energy Technology Data Exchange (ETDEWEB)

This study evaluated potential hydrogeologic mechanisms that may account for increasing moisture content conditions within the sediments of hydroelectric earth dams. Many such dams in Canada are reaching their life spans of approximately 40 years, therefore this study is considered to be an important and timely undertaking. The objective was to develop a method to numerically assess transient groundwater flow processes within old earth structures. The focus of this study was central Manitoba's Grand Rapids Generating Station where progressive movement within the till overburden has been observed since 1977. The possible source of water which is causing higher moisture content and weakness in the overburden material may be the slow wetting-up of the core and progressive increase in seepage to the downstream side. The evolution of flow through the core was evaluated with a modelling program called FRAC3D-VS which ...

2002-07-01

41

Wear Rate and Friction Coefficient in Liquid Nitrogen and ...  

Science.gov (United States)

... Title : Wear Rate and Friction Coefficient in Liquid Nitrogen and Hydrogen of Steel Sliding on Polymer Laminates (Various Fabrics and Polymers. ...

1968-04-01

42

Ultimate Compressive Strength and Nonlinear Stress-Strain ...  

Science.gov (United States)

... Accession Number : ADD421949. Title : Ultimate Compressive Strength and Nonlinear Stress-Strain Curves of Graphite/Epoxy Laminates,. ...

1976-10-12

43

Isoprenylation is required for the processing of the lamin A precursor  

Energy Technology Data Exchange (ETDEWEB)

The nuclear lamina proteins, prelamin A, lamin B, and a 70-kD lamina-associated protein, are posttranslationally modified by a metabolite derived from mevalonate. This modification can be inhibited by treatment with (3-R,S)-3-fluoromevalonate, demonstrating that it is isoprenoid in nature. We have examined the association between isoprenoid metabolism and processing of the lamin A precursor in human and hamster cells. Inhibition of 3-hydroxy-3-methylglutaryl coenzyme A reductase by mevinolin (lovastatin) specifically depletes endogenous isoprenoid pools and inhibits the conversion of prelamin A to lamin A. Prelamin A processing is also blocked by mevalonate starvation of Mev-1, a CHO cell line auxotrophic for mevalonate. Moreover, inhibition of prelamin A processing by mevinolin treatment is rapidly reversed by the addition of exogenous mevalonate. Processing of prelamin A is, therefore, dependent on isoprenoid metabolism. ...

1990-05-01

44

Energy Finite Element Analysis ... - NASA Technical Reports Server  

Science.gov (United States)

structures made out of composite laminates and/or composite sandwich panels. A Spectral Finite Element Method (SFEM) [19, 20] is used for evaluating the ...

45

Embryonic Senescence and Laminopathies in a Progeroid Zebrafish Model  

UK PubMed Central (United Kingdom)

BackgroundMutations that disrupt the conversion of prelamin A to mature lamin A cause the rare genetic disorder Hutchinson-Gilford progeria syndrome and a group of laminopathies....Full Text Available

46

An atlas of the dorsal thalamus of the marsupial brush-tailed possum, Trichosurus vulpecula.  

UK PubMed Central (United Kingdom)

In several respects the dorsal thalamus of Trichosurus presents a level of organizational complexity considerably in advance of that seen in Didelphis. In particular, such features as the lamination...Full Text Available

1978-06-01

47

Laser cutting plastic materials  

Energy Technology Data Exchange (ETDEWEB)

A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

1980-08-01

48

Investigation into the fatigue behaviour of wood laminates for wind energy converter blade design  

Energy Technology Data Exchange (ETDEWEB)

A thesis is presented on improving the understanding of the fatigue properties of wood and fatigue failure mechanisms in the design of wind turbine blades. Three main areas were researched: the effect of R ratio on fatigue life, the effect of moisture on fatigue life and the development of cumulative damage laws. Tests were carried out on mainly four-ply laminates. Recommendations to future work are outlined. (U.K.).

1987-01-01

49

Depositional and dissolutional processes and their resulting thinning patterns within the Middle Devonian Prairie Formation, Williston basin, North Dakota and Montana  

Science.gov (United States)

Within the Williston basin, thickness variations of the Prairie Formation are common and are interpreted to originate by two processes: differential accumulation of salt during deposition and differential removal of salt by dissolution. Unambiguous evidence for each process is rare because the Prairie/Winnipegosis interval is seldom cored within the US portion of the basin. Therefore, indirect methods, using well logs, provide the principal method for identifying characteristics of the two processes. The results of this study indicate that the two processes can be distinguished using correlations within the Prairie Formation. Several regionally correlative brining-upward and probably shoaling-upward sequences occur within the Prairie Formation. Near the basin center, the lowermost sequence is transitional with the underlying Winnipegosis Formation. This transition is characterized by thinly laminated basal carbonates that become increasingly ...

1988-07-01

50

Polypropylene/paper laminates as high voltage power cable insulation  

Energy Technology Data Exchange (ETDEWEB)

A study was carried out to identify optimal laminate/oil combinations for low pressure oil filled and high pressure pipe-type cables, and to establish taping criteria under factory conditions. Laminates from two sources were evaluated in conjunction with Sun XX high viscosity mineral oil and Cosden 015SH polybutene oil for high pressure type cables, and Dussek TC-2288N mineral oil, Shell P2 dedecylbenzene and Chevron DF-100 alkylbenzene for low pressure oil-filled cables. Swelling tests, infrared analysis, dissipation and dielectric measurements, impulse tests and a taping trial were performed. It was found that there is no appreciable difference in performance of both laminates when tested on model cables in a variety of oils. Both types exhibited superior aging characteristics vis-a-vis cellulose paper when tested with a variety of oils and at temperatures up to 105{degree}C. For pipe type cable, high viscosity polybutene ...

1983-08-01

51

Effects of gamma irradiation on the physical properties of laminated packaging materials. 2. polypropylene-polypropylene, polypropylene-polyethylene, and polyester-polyethylene  

International Nuclear Information System (INIS)

This experiment was done to determine the effects of irradiation on the physical properties of three kinds of laminated packaging materials, i.e. polypropylene-polypropylene, polypropylene-polyethylene, polyester-polyethylene. Observations were made on pinhole production, leakage, oil resistance, resistance against insect penetration, colour, odour tensile strength, elongation at break, seal strength and tear resistance. The samples were irradiated with doses of 0, 5 and 10 kGy, then stored at room temperature and examined after 0, 3, 6 and 12 months of storage. The results showed that irradiation doses up to 10 kGy, as well as storage up to 12 months, did not create pinholes, or leakage in pouches prepared from laminated films. The resistance of the films to oil and insect penetration, the colour, and the odour were also unchanged. Both irradiation and storage treatments had a significant effect on physical properties of the ...

52

Sampling method, storage and pretreatment of sediment affect AVS concentrations with consequences for bioassay responses  

International Nuclear Information System (INIS)

Sediment treatment and sediment storage may alter sediment toxicity, and consequently biotic response. Purpose of our study was to combine these three aspects (treatment-toxicity-biotic response) in one integrated approach. We used Acid Volatile Sulfide (AVS) concentrations as a proxy of the disturbance of the sediment. AVS and Simultaneously Extracted Metal (SEM) concentrations were compared to bioassay responses with the freshwater benthic macroinvertebrate Asellus aquaticus. Storage conditions and sediment treatment affected AVS but not SEM levels. AVS can be used as a proxy for sediment disturbance. The best way to pretreat the sediment for use in a bioassay in order to maintain initial AVS conditions was to sample the sediment with an Ekman grab, immediately store it in a jar without headspace, and freeze it as soon ...

2008-01-01

53

Design of sediment-control measures for small areas in surface coal mining. Draft report  

Energy Technology Data Exchange (ETDEWEB)

The manual provides design information for four groups of sediment control structures and treatments which are suitable for use on small areas in surface coal mining. A detailed design procedure is given for each group which will estimate the total amount of settleable solids from a small area with a sediment control structure or treatment for a specific design storm. A procedure is also given for estimating the mean annual sediment yield from a small area. Information on design, installation, maintenance and cost is given for each sediment control measure. Methods for determining the maximum allowable area for each sediment control measure and for design of combined sediment control systems are presented. The design procedures contain numerous nomographs, graphs, and worksheets to facilitate the use of the design procedure. The sediment ...

1982-04-01

54

Design of sediment-control measures for small areas in surface coal mining  

Energy Technology Data Exchange (ETDEWEB)

The manual provides design information for four groups of sediment control structures and treatments which are suitable for use on small areas in surface coal mining. A detailed design procedure is given for each group which will estimate the total amount of settleable solids from a small area with a sediment control structure or treatment for a specific design storm. A procedure is also given for estimating the mean annual sediment yield from a small area. Information on design, installation, maintenance and cost is given for each sediment control measure. Methods for determining the maximum allowable area for each sediment control measure and for design of combined sediment control systems are presented. The design procedures contain numerous nomographs, graphs, and worksheets to facilitate the use of the design procedure. The sediment ...

1982-08-01

55

Coastal sediments '91. Volume 1  

Energy Technology Data Exchange (ETDEWEB)

This volume contains papers delivered at a technical conference of the American Society of Civil Engineers held on June 25-27, 1991 in Seattle, Washington. The conference dealt with the physical aspects of sediment processes in the coastal environment. The papers are presented under three general themes: fundamentals of coastal sediment transport, coastal geologic processes, and engineering applications. The topics of the role of long waves in coastal sediment processes and cross-shore transport are highlighted. Examples of the topics covered include: sediment transport; beach and nearshore sedimentation; shoreline and beach profile changes; longshore and cross-shore transport; storm erosion; inlet sediment processes; gravel transport; coastal structure and sediment interaction; and dredging.

1991-01-01

56

Dielectric-wall linear accelerator with a high voltage fast rise time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators  

Energy Technology Data Exchange (ETDEWEB)

A dielectric-wall linear accelerator is improved by a high-voltage, fast rise-time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators. A high voltage is placed between the electrodes sufficient to stress the voltage breakdown of the insulator on command. A light trigger, such as a laser, is focused along at least one line along the edge surface of the laminated alternating layers of isolated conductors and insulators extending between the electrodes. The laser is energized to initiate a surface breakdown by a fluence of photons, thus causing the electrical switch to close very promptly. Such insulators and lasers are incorporated in a dielectric wall linear accelerator with Blumlein modules, and phasing is controlled by adjusting the length of fiber optic cables that carry the laser light to the insulator surface.

1998-01-01

57

Dielectric-wall linear accelerator with a high voltage fast rise time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators  

Energy Technology Data Exchange (ETDEWEB)

A dielectric-wall linear accelerator is improved by a high-voltage, fast rise-time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators. A high voltage is placed between the electrodes sufficient to stress the voltage breakdown of the insulator on command. A light trigger, such as a laser, is focused along at least one line along the edge surface of the laminated alternating layers of isolated conductors and insulators extending between the electrodes. The laser is energized to initiate a surface breakdown by a fluence of photons, thus causing the electrical switch to close very promptly. Such insulators and lasers are incorporated in a dielectric wall linear accelerator with Blumlein modules, and phasing is controlled by adjusting the length of fiber optic cables that carry the laser light to the insulator surface. 12 figs.

1998-10-13

58

Development of new 500kV laminated paper insulated self-contained oil-filled cable and its accessories  

Energy Technology Data Exchange (ETDEWEB)

This paper describes the development of cellulose paper/plastic film/cellulose paper laminate insulated Self-Contained 500 kV Oil-Filled (OF) Cable and its accessories. Dielectric loss of this new cable was confirmed to be about one third that of conventional kraft paper cable. Moreover, by employing the reduced insulation thickness of 25 mm rather than that of 33 mm, as is usual with conventional cables, the new cable could be made very compact, due to the high dielectric strengths of laminated paper. As a result, the shipping reel length of the new cable, which is about 10% lighter in total weight and 10% smaller in overall diameter than conventional cables, could be dramatically increased. The reliability and the stability of the new cable have been demonstrated by the successful completion of a one and a half year field test.

1988-01-01

59

Lower Cretaceous carbonate megabank, south Florida, depositional setting and petroleum potential  

Energy Technology Data Exchange (ETDEWEB)

Reinterpretation of the South Florida basin reveals that it was a keep-up carbonate shelf during the Lower Cretaceous. Until the Cenomanian, it was connected to the Bahamas and the Cay Sal Bank north of Cuba. The Cenomanian sea level rise was at least partially responsible for the formation of the Florida Straits, isolating the platform. The combination of an abrupt worldwide rise in sea level and subsidence caused the South Florida platform to founder, ending shallow-water and evaporitic sedimentation over the majority of the shelf. The Cay Sal and Bahamian platforms remained as active shallow shelves separated by the Old Bahamas Channel. The Lower Cretaceous sediments are characterized by shallow shelf limestones, dolomites, and evaporites (mostly anhydrite). The evaporite-rich sections, originally thought to represent basinal facies, are reinterpreted as supratidal to shallow subtidal evaporites, based on examination of ...

1987-05-01

60

EVOLUTION OF WHITE DWARF STARS WITH HIGH-METALLICITY PROGENITORS: THE ROLE OF "2"2Ne DIFFUSION  

International Nuclear Information System (INIS)

Motivated by the strong discrepancy between the main-sequence turnoff age and the white dwarf cooling age in the metal-rich open cluster NGC 6791, we compute a grid of white dwarf evolutionary sequences that incorporates for the first time the energy released by the processes of "2"2Ne sedimentation and of carbon/oxygen phase separation upon crystallization. The grid covers the mass range from 0.52 to 1.0 M _s_u_n, and is appropriate for the study of white dwarfs in metal-rich clusters. The evolutionary calculations are based on a detailed and self-consistent treatment of the energy released from these two processes, as well as on the employment of realistic carbon/oxygen profiles, of relevance for an accurate evaluation of the energy released by carbon/oxygen phase separation. We find that "2"2Ne sedimentation strongly delays the cooling rate of white dwarfs stemming from progenitors with high metallicities at moderate luminosities, while ...

2010-08-10

61

High-resolution stratigraphy in a Miocene reservoir of the Niger delta  

Energy Technology Data Exchange (ETDEWEB)

High-resolution sequence stratigraphy concepts are applied to Erema, a Miocene onshore field of the Niger delta. The field's production is decreasing and an up-to-date geological model is essential to monitor the production. We aim to show an approach, using subsurface data and sequence stratigraphic concepts, which results in a time-line (Maximum Flooding Surfaces) correlation scheme. This scheme is based upon a facies model and is destined to guide the study of the characterization of reservoir heterogeneities. Using the cored well as a reference point, the facies model consists of shoreface dunes (planar tabular cross-stratified sandstones) changing landward into fluvial distributary deposits (through cross-stratified sandstones) via a tide-influenced coastal plain facies. The stacking pattern of genetic units shows a seaward stepping phase at the reservoir scale (sixty metres thick) with an abrupt deepening at the top of the reservoir. The proposed ...

1994-06-30

62

Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on photoreactive materials (Research on function separating type photochromic materials); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Kino bunrigata photochromic zairyo ni kansuru kenkyu  

Energy Technology Data Exchange (ETDEWEB)

Research and development has been performed on photochromic materials expected to be used in ultra-high density recording, high resolution indication and photoswitches. With regard to molecular orientation in the ternary system mixed LB film, the result of structural analysis by XPM spectrum revealed that the acceptor constituent in the LB film is so structured that it is separated and laminated with two other constituents, and that the sensitizer constituent and the donor constituent are not recognized of being separated definitely. Regarding the electron movement reaction in the solid phase system, a photo-current measuring experiment was carried out on the laminated film which is vacuum-deposited with the ternary system comprising of the donor, sensitizer, and acceptor. It was concluded that the observed photo-current reflects the electron movement reaction in the solid phase as it is. For the photo-current in the LB film, increase in the ...

1990-03-01

63

Porous tooling process for manufacture of graphite/polyimide composites. Final report  

Energy Technology Data Exchange (ETDEWEB)

A porous tooling system was selected for the processing of Graphite/PMR-15 Polyimide laminates in thickness up to 3.2 mm. (0.125 inch). This tool system must have a reasonable strength, permeability dimensional stability, and thermal conductivity to accomplish curing at 600 F and 200 psi and 200 psi autoclave temperature and pressure. A permeability measuring apparatus was constructed and permeability vs. casting water level determined to produce tools at three different permeability levels. On these tools, laminates of 5, 11, and 22 plies (.027, .060, and 0.121 inch) were produced and evaluated by ultrasonic, mechanical, and thermal tests to determine the effect of the tool permeability on the cured laminates. All tools produced acceptable laminates at 5 and 11 plies but only the highest permeability produced acceptable clear ultrasonic C-Scans. Recommendations are made for future investigations of ...

1981-01-01

66

Lupus  

Medline Plus

... diagnosed. A complete blood count (CBC), urinalysis, blood chemistries, and erythrocyte sedimentation rate (ESR) tests can provide ...

68

Phenomenological modeling of the stress-strain behaivor of ceramic matrix composites with application to stress analysis  

Energy Technology Data Exchange (ETDEWEB)

A plane stress constitutive relation is developed for laminate composites undergoing matrix cracking and therefore displaying significant nonlinear stress-strain behavior. The constitutive relation is similar in some respects to a phenomenological theory of plasticity in that it is fit to data from uniaxial tests. The constitutive equations are specialized to brittle matrix composites (especially CMCs) in the form of cross-piles and quasi-isotropic laminates. Several problems involving stress redistribution at holes and notches due to nonlinear stress-strain behavior are investigated with the aid of the constitutive law.

1995-12-31

69

Development of 275kV oil-filled cable insulated with polypropylene laminated paper (PPLP)  

Energy Technology Data Exchange (ETDEWEB)

In 1969, the authors started R and D on a polypropylene laminated paper (PPLP) as a new low-loss insulating paper for oil-filled (OF) cables. Through the material research and the trial manufacture of 275 kV OF cable and four years of long-term field test, PPLP has reached the stage of commercial use. This paper introduces a summary of the history of the development of PPLP, the characteristics of PPLP and cable, the results of long-term field test of 275 kV cable, and other relevant data.

1982-12-01

70

Geochemical features of re-deposited organic matter occurring in fluvioglacial sediments in the Racib?rz region (Poland): A case study  

British Library Electronic Table of Contents (United Kingdom)

The erosion of rocks rich in organic matter typically leads to the complete mineralization of the organic material. However, in some cases, it is re-deposited to become a part of sediments once more. This process should be considered to be a part of global carbon cycle, possibly much more significant than assumed to-date. The research presented here aims to characterize re-worked organic matter occurring in post-glacial sediments of southern part of Poland, in the Oder river valley (the Racib?rz town region, Miocene, Pleistocene and Holocene age). Organic substances extracted from the sediments originated from organic matter that had resided in rocks eroded by glaciers. Sediments were sampled in two boreholes which sediments were correlated. Sediments were extracted and extracts analyzed w...

2008-01-01

71

Effects of sediment quality on macroinvertebrates in the Sunraysia region of the Murray-Darling Rivers, Australia  

International Nuclear Information System (INIS)

A field-based microcosm approach was tested to identify deterioration of sediment quality in waterways using freshwater macroinvertebrates. The method can potentially identify the nature of contaminants based on species-specific responses. Sediments were collected from the Murray and Darling Rivers and irrigation drains within the Sunraysia region of south-eastern Australia and compared to non-polluted reference sediment. Clean sediments were also spiked with fertiliser to test whether nutrients affected the aquatic fauna. Seven of the eight sediments from the Sunraysia region had a negative impact on the macroinvertebrates, in particular sediment from the Darling River, which supported an impoverished fauna. Three species of chironomid showed varied responses to sediment quality and, although it was hypothesised that nutrients may have ...

2008-12-01

72

Optimization of nonhomogeneous facesheets in composite sandwich plates  

Science.gov (United States)

Minimum weight design is an important criterion in aircraft and spacecraft because it allows either an increased pay-load or higher performance. As a result, the use of composite sandwich panels has grown due to their light weight and high rigidity. In order to further increase the efficiency of these structures, designers have used different materials in different shapes in the facesheets and in the core. One of the most recent innovations has been the use of a uniform net of carbon fibre/epoxy as the facesheets. In the present study, the optimal design of sandwich plates with heterogeneous, facesheets is treated. The plate mass is minimized, considering the first natural frequency and certain failure loads as constraints. Weight reduction is obtained by defining a nonuniform distribution of composite material in the facesheets. Initially, the facesheets are assumed to be constructed of composite strips in a regular pattern. During the optimization process, both ...

1997-01-01

73

CORE OF FAST BREEDER REACTOR  

J-STORE (Japan)

Full Text Available

2006-06-02

74

High resolution sequence stratigraphy in the upper Jurassic carbonate platform of the Paris basin: Reservoir geometries in lagoonal, protected marine and ooids shoals environments  

Energy Technology Data Exchange (ETDEWEB)

Reservoir geometry reconstruction within carbonate platforms has been carried out in the Upper Jurassic of the Paris Basin based on high-resolution sequence stratigraphy correlations (cores and well-logs). 18 cored wells over 25 kM{sup 2} have been correlated (Saint-Clair-sur-Epte field, Gaz de France). During lower and middle Oxfordian the Paris Basin is a carbonate platform prograding southward. This progradational trend can be subdivided into three upper order sequences (parasequences sets, mean duration: one m.y.). The lower parasequence-set is a stacking of shallowing-upward parasequences made up of tidal ooids bars surrounded laterally and backward by more protected environments (large variety of coated grains). The middle parasequence-set is recorded in lagoonal environments with numerous channels and lobes of storm washover-fans. Metric-thick sequences have been correlated over the field. They are ernersive upward (subtidal lagoonal ...

1995-08-01

75

Probabilistic energy based model for prediction of transverse cracking in cross-ply laminates  

Energy Technology Data Exchange (ETDEWEB)

In the present paper an attempt is made to describe transverse cracking of cross-ply ([0{sup o}{sub n}/90{sup o}{sub m}]{sub s}) laminates subjected to an external applied load and a temperature change. For this purpose a new method is suggested which was developed on the basis of the energy balance based finite fracture criterion suggested by Hashin (1996) [Hashin, Z., 1996. J. Mech. Phys. Solids 44, 1129]. In this approach the value of the specific surface energy (the critical energy release rate) is assumed to be dependent on a random microdamage distribution in the material. Hence, it is assumed to be a random function of location. A new probabilistic technique is developed to take this randomness into consideration. It is shown that only one unknown probabilistic function is required, namely the probability density function of the specific surface energy. This is determined by fitting the external stress and the corresponding crack density to experimental data ...

2005-01-01

76

On the indentation failure of carbon-epoxy cross-ply laminates, and its suppression by elasto-plastic interleaves  

Energy Technology Data Exchange (ETDEWEB)

Elastic and elasto-plastic modelling of indentation in CFRP cross-ply laminates has been performed. Detailed knowledge of the field solutions in the volume below the indentor forms the basis for the reported micromechanical interpretation of the observed damage in test specimens. The analysis shows that matrix cracks originate at sites of maximum tensile stress perpendicular to fibers. The predicted stress fields due to indentation show that stress concentrations occur in the interface between alternating plies. It is found that microcracking in this zone is a precursor to the observed failure. This analysis is supported by in-situ scanning electron microscopy during loading by a cylindrical indentor onto the laminate supported on a rigid substrate. The microscopy reveals microdamage in the region of interfacial tensile stress concentrations. The onset of indentation failure in these layered composites suggests that plastic interleaves would ...

1997-08-01

77

Uranium studies in the Tims Branch and Steed Pond system  

Energy Technology Data Exchange (ETDEWEB)

During the weekend of September 2--3, 1984, a part of the wooden spillway for Steed Pond gave way and the pond slowly drained. Consideration is being given to leaving Steed Pond dry. Steed Pond has accumulated some of the uranium discharged from 300 Area operations and past surveys have shown that the uranium concentration in the sediments ranges between 20 and 531 pCi/gm. The recently completed aerial survey of the exposed area of Steed Pond showed that the uranium was widely spread in the sediments of Steed Pond. Until ground cover is established over the exposed pond sediments, they will be subject to erosion. As much as 90 tons of sediment could be eroded from the exposed sediments in Steed Pond the first year, but the erosion could be reduced to 5--15 tons by establishing a ground cover such as rye grass. Only about 40% of the eroded sediment would be ...

1984-11-01

78

Methanogen Diversity Evidenced by Molecular Characterization of Methyl Coenzyme M Reductase A (mcrA) Genes in Hydrothermal Sediments of the Guaymas Basin  

UK PubMed Central (United Kingdom)

The methanogenic community in hydrothermally active sediments of Guaymas Basin (Gulf of California, Mexico) was analyzed by PCR amplification, cloning, and sequencing of methyl coenzyme M reductase...Full Text Available

2005-08-01

79

Isolation and characterization of quinoline-degrading bacteria from subsurface sediments.  

UK PubMed Central (United Kingdom)

Two gram-negative, motile bacteria isolated from deep subsurface sediments mineralized the nitrogen-containing polyaromatic hydrocarbon quinoline under aerobic conditions and transformed quinoline to...Full Text Available

1989-04-01

80

Hexadecane mineralization in oxygen-controlled sediment-seawater cultivations with autochthonous microorganisms.  

UK PubMed Central (United Kingdom)

Laboratory studies investigated the influence of dissolved oxygen tension (DOT) on microbial degradation of hexadecane in cultures with sediment-seawater suspensions. With a fermentor system, it was...Full Text Available

1992-09-01

81

Field Investigations in the Tow Study Programme for Coastal Sediment Transport in the Netherlands.  

Science.gov (United States)

Field campaigns were conducted in 1981 and 1982/83 on the Dutch coast near Egmond. Measurements were made of surface elevations, water velocities and sediment concentrations in 3 to 8 surf zone locations and 2 to 5 offshore locations simultaneously. A des...

1985-01-01

82

Effect of Wastewater Treatment Plant Effluent on Microbial Function and Community Structure in the Sediment of a Freshwater Stream with Variable Seasonal Flow?  

UK PubMed Central (United Kingdom)

We investigated the effects of wastewater treatment plant (WWTP) discharge on the ecology of bacterial communities in the sediment of a small, low-gradient stream in South Australia. The quantification...Full Text Available

2008-05-01

83

Desorption of polycyclic aromatic hydrocarbons (PAH`s) from calcite and quartz sediments to seawater  

Energy Technology Data Exchange (ETDEWEB)

Polycyclic aromatic hydrocarbons (PAH`s) are ubiquitous hydrophobic organic pollutants in the marine environment. Many of the PAM`s are classified as possible carcinogens or mutagens, therefore they are of considerable concern to human and environmental health. The highest concentrations are found in coastal regions due to anthropogenic activities including oil spills, tanker operations, incomplete fossil fuel combustion and runoff. The sources and distribution of PAM`s in sediments are fairly well known, while the fate and transport of PAH`s in the marine environment are less known. Desorption is an important factor influencing the fate and transport of hydrophobic molecules at the seawater/sediment interface. The desorption of PAH`s from contaminated marine sediments to the water column/pore water affects the availability of the pollutant to biota. The sorption of PAH`s is determined in part by the organic carbon content ...

1996-12-31

84

Community Structure of Ammonia-Oxidizing Bacteria within Anoxic Marine Sediments  

UK PubMed Central (United Kingdom)

The potential for oxidation of ammonia in anoxic marine sediments exists through anaerobic oxidation by Nitrosomonas-like organisms, utilizing nitrogen dioxide, coupling of nitrification,...Full Text Available

2003-03-01

85

Analysis of the Sulfate-Reducing Bacterial and Methanogenic Archaeal Populations in Contrasting Antarctic Sediments  

UK PubMed Central (United Kingdom)

The distribution and activity of communities of sulfate-reducing bacteria (SRB) and methanogenic archaea in two contrasting Antarctic sediments were investigated. Methanogenesis dominated in freshwater...Full Text Available

2003-06-01

86

Radionuclide particle transport, sedimentation and resuspension in the Forsmark and Laxemar coastal regions  

Energy Technology Data Exchange (ETDEWEB)

In the safety assessment of a potential repository for spent nuclear fuel, it is important to assess the consequences of a hypothetical leak of radionuclides through the seabed and into a waterborne transport phase. Radionuclides adsorbed to sediment particles may be transported great distances through the processes of sedimentation and resuspension. This study investigates the transport patterns of sediment particles of two different sizes, released in the Forsmark and Laxemar area. The results show that the closed waters around Forsmark to a higher degree makes the particles stay in the area close to the release points

2007-12-15

87

Particle Entrainment Simulator at the US Army Engineer ...  

Science.gov (United States)

... operation, experimental data reduction, and application of PES results to studies related to estuarine and coastal sediment transport problems are ...

2005-09-01

88

GAS EVOLUTION FROM INSULATING MATERIALS FOR SUPERCONDUCTING COIL OF ITER BY GAMMA RAY IRRADIATION AT LIQUID NITROGEN TEMPERATURE  

International Nuclear Information System (INIS)

A laminated material composed of glass cloth/polyimide film/epoxy resin will be used as an insulating material for superconducting coil of International Thermonuclear Experimental Reactor (ITER). In order to keep safe and stable operation of the superconducting coil system, it is indispensable to evaluate radiation resistance of the material, because the material is exposed to severe environments such as high radiation field and low temperature of 4 K. Especially, it is important to estimate the amount of gases evolved from the insulating material by irradiation, because the gases affect on the purifying system of liquid helium in the superconducting coil system. In this work, the gas evolution from the laminated material by gamma ray irradiation at liquid nitrogen temperature (77 K) was investigated, and the difference of gas evolution behavior due to difference of composition in the epoxy resin was discussed. It was found that the main gases ...

2008-03-03

89

A study of kerf characteristics in abrasive waterjet machining of graphite/epoxy composite  

Energy Technology Data Exchange (ETDEWEB)

Kerf geometry, kerf wall features, and cutting front characteristics of an Abrasive Waterjet (AWJ) machined Graphite/Epoxy (Gr/Ep) laminate were studied. A macroscopic analyses suggests that geometrical features associated with AWJ machining of Gr/Ep laminates are influenced by three macro regions along the cutting depth. The presence of these regions, including initial damage at jet entry, smooth cutting, and rough cutting near the jet exit, depends on the operating conditions. Design of experiments and analysis of variance were used to determine the effect of cutting parameters on kerf characteristics and to develop empirical models for kerf profile and features of the three distinct macroscopic regions. Cutting front analysis revealed that the mechanisms of material removal in AWJ machining of Gr/Ep do not change over the jet penetration depth. In general, high quality uniform cuts may be obtained by minimizing initial damage at the jet ...

1996-04-01

90

Fatigue life prediction of cross-ply composite laminates  

Energy Technology Data Exchange (ETDEWEB)

To predict the fatigue life of fiber reinforced composites, fatigue process of CFRP laminates of [0 /90 ]{sub s} is investigated and the influence of damages occurring at fiber, matrix and fiber/matrix interface on the various critical strengths and the relationship between residual critical strength and failure are discussed. As a result, it was shown that fatigue strength (i.e. fatigue life) consisted of residual critical strength and stresses occurring at each layer (0 and 90 layers) and interlayer. Moreover, the fatigue failure occurred because the residual critical strength of each layer and interlayer decreased with dependence of their microdamage densities, so that the fatigue life can be predicted by evaluating microdamage behavior in fatigue process. (orig.) 14 refs.

1997-11-15

91

The influence of Cu contamination on Nereis diversicolor bioturbation  

British Library Electronic Table of Contents (United Kingdom)

Aquatic sediments feature a two-way interaction between contaminants and benthic macrofauna. The effect of the macrofauna community on the transport of contaminants in sediment has received considerable attention. Yet, few studies have investigated the reverse effect, i.e., the influence of contaminants on bioturbation activity. To this end, we performed laboratory experiments to investigate the effect of copper contamination on sediment reworking activity of the ragworm Nereis diversicolor. A density of 570 ind m2 was introduced in mesocosms containing natural and copper spiked (2.99 nmol Cu g?1) cohesive intertidal sediments from Ponta da Erva (Tejo estuary, Portugal). Luminophore tracers were used to quantify sediment reworking activity over time (2, 7, 14 and 21 days). Bioturbation was...

2006-01-01

92

Development of a Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST) Modeling System  

British Library Electronic Table of Contents (United Kingdom)

Understanding the processes responsible for coastal change is important for managing our coastal resources, both natural and economic. The current scientific understanding of coastal sediment transport and geology suggests that examining coastal processes at regional scales can lead to significant insight into how the coastal zone evolves. To better identify the significant processes affecting our coastlines and how those processes create coastal change we developed a Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST) Modeling System, which is comprised of the Model Coupling Toolkit to exchange data fields between the ocean model ROMS, the atmosphere model WRF, the wave model SWAN, and the sediment capabilities of the Community Sediment Transport Model. This formulation builds upon ...

2010-01-01

93

The role of condensed carbonaceous materials on the sorption of hydrophobic organic contaminants in subsurface sediments.  

Science.gov (United States)

The identification and characterization of carbonaceous materials (CMs) that control hydrophobic organic chemical (HOC) sorption is essential to predict the fate and transport of HOCs in soils and sediments. The objectives of this paper are to determine the types of CMs that control HOC sorption in the oxidized and reduced zones of a glacially deposited groundwater sediment in central Illinois, with a special emphasis on the roles of kerogen and black carbon. After collection, the sediments were treated to obtain fractions of the sediment samples enriched in different types of CMs (e.g., humic acid, kerogen, black carbon), and selected fractions were subject to quantitative petrographic analysis. The original sediments and their enrichment fractions were evaluated for their ability to sorb trichloroethene (TCE), a common groundwater pollutant. Isotherm results and mass fractions of ...

2008-03-01

94

Partitioning of trace metals in the chemical fractions of bed-load sediments of Nahr-Ibrahim river, Lebanon  

International Nuclear Information System (INIS)

Full text.Sediments are the ultimate sink of trace elements. The total metal analysis may only give information concerning possible enrichment of metals. The analysis of metal partitioning in the different chemical components of sediments (exchangeable, carbonate, easily reducible, moderately reducible, organic and residual); give a detailed information on the way in which these metals are bound to sediments, their mobilization capacity and their ability to affect water quality under different environmental conditions. The studied river basin is dominated by limestone formation, the enrichment of metals in the carbonate sediment fraction is a high probability. The objective of the study was to determine the percentage of the total metal content (Fe, Mn, Zn, Cu and Pb) in the six chemical fractions of the bed load sediments of Nahr-Ibrahim river during the dry season and verify the ...

1999-11-02

95

Elemental compositions of sediments at Haiphong harbour area as determined by nuclear analytical techniques application in sediment transport studies and conservation of the environment  

International Nuclear Information System (INIS)

Nuclear analytical techniques were applied to determine the elemental compositions of suspended and bottom sediments, collected at different sites in Haiphong harbor area (North Viet nam). The study was aimed at: 1/Understanding the origin of the sediment filling up the access channel and causing large expenditures for dredging operations. 2/Determining the background concentrations of trace elements in sediment. This would allow to detect in the future any pollution caused by the discharge of industrial wastes in the water due to the growing industrialization of the area. 3/Identifying the elements, which can be served as activatable tracers in sediment transport studies. The results obtained for the concentrations of nearly 30 elements show rather similar elemental compositions, reflecting a common origin of the sediments taken from different locations in the harbour area. The ...

1992-03-09

96

Sequential extraction of heavy metals in river sediments of an abandoned pyrite mining area: pollution detection and affinity series  

Energy Technology Data Exchange (ETDEWEB)

In this paper heavy metal pollution at an abandoned Italian pyrite mine has been investigated by comparing total concentrations and speciation of heavy metals (Fe, Cu, Mn, Zn, Pb and As) in a red mud sample and a river sediment. Acid digestions show that all the investigated heavy metals present larger concentrations in the sediment than in the tailing. A modified Tessier's procedure has been used to discriminate heavy metal bound to organic fraction from those originally present in the mineral sulphide matrix and to detect a possible trend of metal mobilisation from red mud to river sediment. Sequential extractions on bulk and size fractionated samples denote that sediment samples present larger percent concentrations of the investigated heavy metals in the first extractive steps (I-IV) especially in lower dimension size fractionated samples suggesting that heavy metals in the ...

2004-11-01

97

Sequential extraction of heavy metals in river sediments of an abandoned pyrite mining area: pollution detection and affinity series  

International Nuclear Information System (INIS)

In this paper heavy metal pollution at an abandoned Italian pyrite mine has been investigated by comparing total concentrations and speciation of heavy metals (Fe, Cu, Mn, Zn, Pb and As) in a red mud sample and a river sediment. Acid digestions show that all the investigated heavy metals present larger concentrations in the sediment than in the tailing. A modified Tessier's procedure has been used to discriminate heavy metal bound to organic fraction from those originally present in the mineral sulphide matrix and to detect a possible trend of metal mobilisation from red mud to river sediment. Sequential extractions on bulk and size fractionated samples denote that sediment samples present larger percent concentrations of the investigated heavy metals in the first extractive steps (I-IV) especially in lower dimension size fractionated samples suggesting that heavy metals in the ...

2004-11-01

98

Effects of a chelating resin on metal bioavailability and toxicity to estuarine invertebrates: Divergent results of field and laboratory tests  

International Nuclear Information System (INIS)

Benthic invertebrates can uptake metals through diffusion of free ion solutes, or ingestion of sediment-bound forms. This study investigated the efficacy of the metal chelating resin SIR 300TM in adsorbing porewater metals and isolating pathways of metal exposure. A field experiment (Botany Bay, Sydney, Australia) and a laboratory toxicity test each manipulated the availability of porewater metals within contaminated and uncontaminated sediments. It was predicted that within contaminated sediments, the resin would adsorb porewater metals and reduce toxicity to invertebrates, but in uncontaminated sediments, the resin would not significantly affect these variables. Whereas in the laboratory, the resin produced the predicted results, in the field the resin increased porewater metal concentrations of contaminated sediments for at least 34 days and decreased abundances of four ...

2010-05-01

99

The discussion on the relationship between high-resolution sequence stratigraphy and uranium mineralization of Zhiluo formation in Dongsheng area, ordos basin  

International Nuclear Information System (INIS)

According to the data of drill cores, outcrops and well logging, two orders base-level cycles are recognized from Zhiluo Formation in Dongsheng area, which consist of 8-14 short-term base-level cycles and 3 mid-term base-level cycles, and their structural types and stacking patterns are discussed by using principles and methods of high-resolution sequence stratigraphic theory. Based on the correlation of mid-term base-level cycles, the control of the A/S (Accommodation/Sediment supply) ratio in mid-term base-level cycles on the scale of sand bodies and physical properties of reservoir is analysed. Studies show that the sand bodies of braided stream in MSC1 of Zhiluo Formation are favourable to uranium mineralization, however, the sand bodies of meandering river in MSC2 and MSC3 are not favourable to uranium mineralization. The change of the A/S results in the difference in characters of sand body, such as physical properties, continuity and so ...

2007-01-01

100

Sequence stratigraphy and facies associations of Falher units C and D, lower Cretaceous, Alberta Basin, Canada  

Energy Technology Data Exchange (ETDEWEB)

The Lower Cretaceous Falher Member (Spirit River Formation) in the Deep Basin of Alberta is composed of 5 units (A-E) comprising the reservoir of the giant Elmworth gas field. Using high resolution sequence stratigraphy, 333 well logs and 65 cores were integrated to understand the evolution of Falher C and D in the study area. Five major faces associations were defined in each unit. The basal surface of Falher D overlies nonmarine deposits (Falher E) and is defined by a marine flooding surface (transgressive surface of erosion) partially modified by a subsequent regressive surface of erosion. Southward, all the facies become more continental and the marine flooding surface passes into a lagoon-on-nonmarine contact. Falher D contains a series of shingled marine sandstone lenses separated by erosional surfaces interpreted as seaward-dipping ravinement surfaces indicating different phases of marine transgression-regression. The Falher C basal surface is a marine ...

1996-08-01

101

Depositional history of Sunniland Limestone (Lower Cretaceous), Raccoon Point field, Collier County, Florida  

Energy Technology Data Exchange (ETDEWEB)

The Sunniland Limestone (Lower Cretaceous), consisting of carbonate rock and anhydrite, bears the only oil and gas production in southern Florida. Raccoon Point field, Collier County, Florida, is one of 13 fields discovered along the Sunniland producing trend, producing from paleotopographic highs associated with shelfal patch reefs and high-energy bioclastic deposits. Deposition of the Sunniland Limestone, as determined from detailed stratigraphic and microfacies analysis (using core, thin sections, and well logs), occurred in three transgressive-regressive packages or sequences: the lower, middle, and upper Sunniland. Each sequence is further divided into successive shallowing-upward intervals or parasequences. The dolomite reservoirs at Raccoon Point field occur at the top of the middle Sunniland and within the upper Sunniland. They are interpreted as high-energy deposits formed from bioclastic debris and as a network between rudist mounds. Reservoir development ...

1988-09-01

102

Multiplication measurements for initial startup with the mockup core for the FFTF  

International Nuclear Information System (INIS)

... fftf reactor mockup multiplication factors reactivity worths reactor cores reactor

1974-10-27

103

DARPA DTN Phase 3 Core Engineering Support  

Science.gov (United States)

This report covers the initial DARPA DTN Phase 3 activities as JPL provided Core Engineering Support

2010-01-01

104

Eddy current testing of CFRP; New probes and techniques. Wirbelstrompruefung von Kohlefaser-Kompositen; Neue Sonden und Messverfahren  

Energy Technology Data Exchange (ETDEWEB)

Nondestructive inspection of carbon fibre-reinforced plastics (CRFP) using eddy current methods is based not only on the conductivity of the fibres. High frequencies (up to 10 MHz) give access to capacitive effects reflecting properties of the matrix. The paper presents a method using rotating eddy current probes to measure the anisotropic electrical properties. Potential applications of this method are the structural identification of laminates and the estimating of its degradation. (orig.)

1994-01-01

105

Sorption of atrazine and phenanthrene by organic matter fractions in soil and sediment  

International Nuclear Information System (INIS)

Atrazine and phenanthrene (Phen) sorption by nonhydrolyzable carbon (NHC), black carbon (BC), humic acid (HA) and whole sediment and soil samples was examined. Atrazine sorption isotherms were nearly linear. The single-point organic carbon (OC)-normalized distribution coefficients (K_O_C) of atrazine for the isolated HA1, NHC1 and BC1 from sediment 1 (ST1) were 36, 550, and 1470 times greater than that of ST1, respectively, indicating the importance of sediment organic matter, particularly the condensed fractions (NHC and BC). Similar sorption capacity of atrazine and Phen by NHC but different isotherm nonlinearity indicated different sorption domains due to their different structure and hydrophobicity. The positive relationship between (O + N)/C ratios of NHC and atrazine log K_O_C at low concentration suggests H-bonding interactions. This study shows that sediment is probably a less effective sorbent ...

2010-12-01

106

Radionuclide adsorption characteristics around coastal water  

Energy Technology Data Exchange (ETDEWEB)

The adsorption capacity of radionuclides onto suspended sediment was experimented on each of the coastal seawater sampled around the Kori and the Wolsung nuclear power plant. During the experiment the quantity and size fraction of suspended sediment were adjusted and the seawater and sediment chemistry is approximated to the expected field condition. Because the sorption capacity depends on the specific minerals, ocean chemistry and radionuclide involved, it is necessary to analyze sediment mineralogy. Clay mineral is dominant in seabed mineral and suspended sediment as the result of x-ray diffraction. Radionuclide sorbed to silty-clay mineral can be rather transported to ocean than scavenged to seabed because of low quantity and fine grained suspended sediment in the coast around the Kori and the Wolsung. The result of adsorption examinations shows that {sup ...

1999-07-01

107

Radionuclide adsorption characteristics around coastal water  

International Nuclear Information System (INIS)

The adsorption capacity of radionuclides onto suspended sediment was experimented on each of the coastal seawater sampled around the Kori and the Wolsung nuclear power plant. During the experiment the quantity and size fraction of suspended sediment were adjusted and the seawater and sediment chemistry is approximated to the expected field condition. Because the sorption capacity depends on the specific minerals, ocean chemistry and radionuclide involved, it is necessary to analyze sediment mineralogy. Clay mineral is dominant in seabed mineral and suspended sediment as the result of x-ray diffraction. Radionuclide sorbed to silty-clay mineral can be rather transported to ocean than scavenged to seabed because of low quantity and fine grained suspended sediment in the coast around the Kori and the Wolsung. The result of adsorption examinations shows that ...

1999-11-04

108

Landslides affecting sedimentary characteristics of reservoir basin  

British Library Electronic Table of Contents (United Kingdom)

Typhoons Aere (2004) and Matsa (2005) caused high nephelometric turbidity in the Shihmen reservoir in northern Taiwan, jeopardizing the operation of the reservoir for several days, and ultimately impacting the living conditions and economy of the downstream residents. The torrential rains caused landslides and debris flows in upland areas, and flowed into riverbeds, likely contributing significantly to the suspended sediment yields in the reservoir. This investigation elucidates how upland landslides affect sediment attributes in the reservoir basin. Study methods including field observations, spatial analysis in GIS and aerial photo interpretation are adopted to trace the sediment sources and contributing factors to the landslide. Torrential rains induced landslides and debris-flows uplan...

2010-01-01

109

Sulfamethoxazole sorption by sediment fractions in comparison to pyrene and bisphenol A  

British Library Electronic Table of Contents (United Kingdom)

The environmental behavior of antibiotics has attracted great research attention. However, their sorption mechanisms in soils/sediments are still unknown. Comparison of the sorption properties between the widely-studied hydrophobic organic contaminants (HOCs) and antibiotics may provide valuable insight to antibiotic sorption mechanisms. Thus, in this study batch experiments for pyrene (PYR), bisphenol A (BPA), and sulfamethoxazole (SMX) sorption were conducted on a sediment sample and its separated fractions. Our results showed the high sorption of PYR on black carbon and organic matter. Although high sorption of SMX was observed for both separated organic fractions (humic acids) and inorganic mineral particles, the original sediment particles showed relatively low sorption. Competitive s...

2010-01-01

110

Spatial Variability of Wave Data from Todos Santos Bay, Baja California, Mexico  

Science.gov (United States)

... and operation of marine structures and to estimate coastal sediment transport. While the timely collection and report of high ... ...

111

Smooth Particle Hydrodynamics for Surf Zone Waves  

Science.gov (United States)

... Zou, S. and RA Dalrymple, ``Coastal Sediment Transport Simulation by Smoothed Particle Hydrodynamics,'' Journal of Waterways, Ports, Coastal ...

2011-05-15

112

R/V Laurence M. Gould LMG0303 - Development of a luminescence - NASA  

Science.gov (United States)

R/V Laurence M. Gould LMG0303 - Development of a luminescence dating capability for Antarctic glaciomarine sediments: Tests of signal zeroing at the ...

114

Polycyclic aromatic hydrocarbon composition and potential sources for sediment samples from the Beaufort and Barents Seas  

Energy Technology Data Exchange (ETDEWEB)

The PAH (polycyclic aromatic hydrocarbons) concentration in coastal zones in the Arctic were studied. Assessment in remote areas is difficult because PAHs contamination from fossil fuel discharges and combustion can be masked by PAHs from natural sources, such as oil seeps, bitumens and forest fires. It is believed that the most important source of anthropogenic PAHs in the Arctic is the long range transport of combustion emissions. A comparison study of PAH distribution between the Beaufort Sea and the Barents Sea led to the interpretation of PAH distributions in terms of potential sources and their geochemistry. PAH concentrations in the Barents Sea sediments were found to be 2 to 20 times lower than in the Beaufort Sea sediments; they are believed to be from anthropogenic sources. In the Beaufort Sea the sediments were found to have been derived from natural sources. 7 refs., 2 figs.

1996-07-01

115

Overview of geology, hydrology, geomorphology, and sediment ...  

Science.gov (United States)

Jun 16, 2011 ... Description: Within the Deschutes River basin of central Oregon, the geology, hydrology, and physiography influence geomorphic and ecologic ...

116

Modelling the reworking effects of bioturbation on the incorporation of radionuclides into the sediment column: implications for the fate of particle-reactive radionuclides in Irish Sea sediments  

British Library Electronic Table of Contents (United Kingdom)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a 137Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data...

2010-01-01

117

Luminescence dating of marine and fluvial sediments ... - GCMD - NASA  

Science.gov (United States)

INAA (instrumental neutron activation analysis) analyses have been made of subsamples of each OSL (Optically stimulated luminescence) sample, for dosimetry ...

118

Lithofacial characteristics and geological structure of the Mesozoic to Cenozoic sediments of the Zapadno Rakushechniy Sea site  

Energy Technology Data Exchange (ETDEWEB)

Seismic exploration is used to identify the Zapadno Rakushechniy Sea uplift. It is promising with respect to prospecting for oil and gas deposits as a result of its proximity to the Severo Rakushechniy deposit with commercial oil and gas presence in the Triassic sediments. Structural prospecting wells are drilled at the Zapadno Rakushechnyy Sea site which open sediment from the Neogene to the upper Triassic. The Triassic sediments are represented by a thick terrigeneous to carbonate series washed out to a varying degree and covered by Jurassic sediments. A comparison of the lithofacial composition of the Triassic sediments shows that the thickness and lithological composition o the Triassic rocks varies by site, while the sediments of the upper Triassic are sharply reduced in thickness to the southsouthwest. The older are the sediments of ...

1984-01-01

119

Improvement of lake water quality by paying farmers to abate nonpoint source pollution. Research report  

Energy Technology Data Exchange (ETDEWEB)

To mitigate damages caused by agricultural runoff, private lake owners' associations are paying for inlake and instream pollution abatement measures and on land-conservation practices. This phenomenon supports the notion that individuals who benefit from improved water quality should be willing to pay part of the abatement costs. The research suggests that on land-conservation measures can substantially reduce sediment delivery at low cost. The Sediment Economics (SEDEC) model was modified and then used to select and to site management systems that achieved stated sediment goals at least cost. Other resource policies such as T value, no-till, and contouring were compared with the least-cost frontier and shown to be more costly. The noncropland areas substantially reduced sediment delivery to water channels and lowered abatement costs. Further research is needed for long-range watershed-planning ...

1988-12-01

120

Evaluation of Upland Disposal of John F. Baldwin Ship ...  

Science.gov (United States)

... Accession Number : ADA270425. Title : Evaluation of Upland Disposal of John F. Baldwin Ship Channel Sediment. Descriptive Note : Final rept.,. ...

1993-07-01

121

Decision Tree Phytoremediation.  

Science.gov (United States)

Phytoremediation, a technology using plants to remediate or stabilize contaminants in soil, groundwater, or sediments, has recently received a great deal of attention from regulators, consultants, responsible parties, and stakeholders. phytoremediation ha...

1999-01-01

122

A 1500-year record of lead, copper, arsenic, cadmium, zinc level in Antarctic seal hairs and sediments  

British Library Electronic Table of Contents (United Kingdom)

To reconstruct the profiles of heavy metal levels in the South Ocean ecosystem of Antarctica, the concentrations of lead (Pb), copper (Cu), arsenic (As), cadmium (Cd), and zinc (Zn) in seal hairs and lake sediments spanning the past 1500?years from Fildes Peninsula of King George Island and in weathering lake sediments from Nelson Island of West Antarctica were determined. The lead contents in the seal hairs and the weathering sediments show a sharp increase since the late 1800s, very likely due to anthropogenic contamination from modern industries. After the 1980s, the Pb content in seal hairs dropped by one-third, apparently due to the reduced usage of leaded gasoline in the Southern Hemisphere. Copper arises mainly from the weathering process, and its level may be substantially affected...

2006-01-01

123

Plutonium distribution and remobilization in sediments of the Rhone River mouth (North-Western Mediterranean); Distribution et remobilisation du plutonium dans les sediments du prodelta du Rhone (Mediterranee nord-occidentale)  

Energy Technology Data Exchange (ETDEWEB)

The aim of the present study was to describe the distribution and remobilization of plutonium (Pu) in the sediments off the Rhone river mouth. Most of the {sup 238}Pu and {sup 239,240}Pu isotopes introduced into the Rhone River were discharged by the liquid effluents released from the Marcoule reprocessing plant, located 120 km upstream the river mouth. Due to its high affinity for particles and its long half life, {sup 238}Pu is a promising tracer to follow the dispersion of particulate matter from the Rhone River to the Mediterranean Sea. During the 3 REMORA cruises, sediment samples were specifically collected in the Rhone pro-delta area and more offshore on the whole continental shelf of the Gulf of Lions. The measurements of alpha emitters gave a first detailed spatial distribution of Pu isotope concentrations in surface sediments off the Rhone mouth. Using {sup 137}Cs concentrations and their correlations with Pu ...

2004-06-15

124

Equivalent magnetic noise in magnetoelectric Metglas/Pb(Mg1/3Nb2/3)O3-PbTiO3 laminate composites  

British Library Electronic Table of Contents (United Kingdom)

Abstract We have experimentally and theoretically investigated the equivalent magnetic noise in a magnetoelectric Metglas/ 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 laminate sensor unit by considering the constituent noise sources of dielectric loss (NDE) and DC leakage resistance (NR). In the low frequency range (f = 1 Hz), theory predicts that NR dominates the noise charge (1.6 times larger than NDE), with a 1 Hz noise of 9.1\\;{\\rm pt}/\\sqrt {\\rm Hz}. The experimental equivalent magnetic noise was 10.8\\;{\\rm pt}/\\sqrt {\\rm Hz}. This observed value is slightly higher than the predicted one, which might be due to an oversimplification of the theoretical model in terms of electrical charge amplifier and external vibration noise sources. ( 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

2011-01-01

125

Composite electrode substrate for fuel cell requiring no separator plate and its production method; Separeta ban wo fuyo tosuru nenryo denchiyo fukugo denkyoku kiban oyobi sono seizoho  

Energy Technology Data Exchange (ETDEWEB)

This invention relates to the production method of composite electrode substrate for fuel cell. An impermeable material is used for edge sealant. The sealant is put in the clearance between two electrodes consisting of porous carbon material via thermoplastic resin sheet, and heated while being pressed. This production method increases the adherence between the porous carbon bodies and reduces the contact resistivity at the joint interface. Consequently, it becomes possible to produce the composite electrode for fuel cell without separator, resulting in simplification of assembly work, weight reduction, and downsizing. The preferable porous carbon body is made from shrinkage-treated fiber. After sheet forming, the thermosetting resin is impregnated, and then it is burnt to carbonization. Or mixed sheet of rayon and acrylic fiber is laminated to be heated and pressed without impregnating the resin. The pressed resin is then burnt to carbonization. The preferable ...

1996-04-12

126

Vertical and Horizontal Variations in the Physiological Diversity of the Aerobic Chemoheterotrophic Bacterial Microflora in Deep Southeast Coastal Plain Subsurface Sediments  

UK PubMed Central (United Kingdom)

Aerobic chemoheterotrophic bacteria were isolated from surface soils and coastal plain subsurface (including deep aquifer) sediments (depths to 265 m) at a study site near Aiken, S.C., by plating on...Full Text Available

1989-05-01

127

Role of paleogeomorphological research in analyzing the influence of deep-lying faults on the sediment accumulation conditions in the latter Cretaceous stage in the Western Capital Caspian Sea Valley  

Energy Technology Data Exchange (ETDEWEB)

The spatial connection between the zones of deep-lying faults and the narrowly-localized paleo-relief sections posessing an anomolous sedimentation condition in the latter Cretaceous is identified. It is established that this is of significance in choosing the primary regions for conducting oil exploration.

1980-01-01

128

Persistence of spilled oil along the Beaufort Sea coast  

Energy Technology Data Exchange (ETDEWEB)

The research project for which this is the final report was initiated in 1977 with the following three major objectives: Assess the retention potential for spilled oil within the coastal environments of Alaska's Beaufort Sea; Characterize the morphology and sediments of the Beaufort coast; Determine, as precisely as possible, the annual longshore sediment transport rate.

1980-04-01

129

Microbial characterization of a radionuclide- and metal-contaminated waste site  

Energy Technology Data Exchange (ETDEWEB)

The operation of nuclear processing facilities and defense-related nuclear activities has resulted in contamination of near-surface and deep-subsurface sediments with both radionuclides and metals. The presence of mixed inorganic contaminants may result in undetectable microbial populations or microbial populations that are different from those present in uncontaminated sediments. To determine the impact of mixed radionuclide and metal contaminants on sediment microbial communities, we sampled a processing pond that was used from 1948 to 1975 for the disposal of radioactive and metal-contaminated wastewaters from laboratories and nuclear fuel fabrication facilities on the Hanford Site in Washington State. Because the Hanford Site is located in a semiarid environment with average rainfall of 159 mm/year, the pond dried and a settling basin remained after wastewater input into the pond ceased in 1975. This processing pond ...

1993-04-01

130

Influence of Hexagenia on the fate and bioavailability of contaminants in sediment  

International Nuclear Information System (INIS)

The influence of sediment dwelling macroinvertebrates on fate and bioavailability of contaminants in freshwater systems was determined using the burrowing mayfly, Hexagenia limbata, as a representative benthic organism. Two series of experiments were conducted: the first to determine the effect of mayflies on movement of contaminants into sediment and organisms, and the second to examine the effect of mayflies on release of contaminants from sediments to the water column and their subsequent accumulation in fish. Concentrations of "1"4C labelled DDT, hexachlorobenzene (HCB), and dihexylphthalate (DHP) in water were 0.11 +/- 0.01, 0.062 +/- 0.005 and 0.006 +/- 0.007 ppb, respectively. Total mass of DHP in the burrow wall was about equal to mass on the surface, indicating that mayflies were capable of doubling the amount of DHP sorbed per unit surface area of sediment. Adsorption of contaminants from ...

131

Carcinogenicity of Black Rock Harbor sediment to the eastern oyster and trophic transfer of Black Rock Harbor carcinogens from the blue mussel to the winter flounder.  

UK PubMed Central (United Kingdom)

The eastern oyster (Crassostrea virginica) developed neoplastic disorders when experimentally exposed both in the laboratory and field to chemically contaminated sediment from Black Rock Harbor (BRH),...Full Text Available

1991-01-01

132

Behavior and impact assessment of heavy metals in estuarine and coastal zones  

Energy Technology Data Exchange (ETDEWEB)

Contents include: introduction; river systems; physical processes; chemical processes; estuaries and coastal zone; introduction; physical processes; chemical processes; the role of sediments; introduction; the anoxic layer; major-element chemistry; minor-element chemistry; the oxic-anoxic interface; assessment; introduction; analysis of sediments; modelling.

1987-01-01

133

On the dependence of some helium shell flash characteristics on core mass  

Energy Technology Data Exchange (ETDEWEB)

A theoretical derivation of the intershell mass--core mass relation of Paczynski is attempted. Formulae developed by Sugimoto and Fujimoto are extended to less massive (m/sub c/< or approx. =1) cores.

1980-08-15

134

FFTF reactor assembly system technology  

Science.gov (United States)

An overview is presented of the FFTF reactor and plant together with descriptions of core components, core internals, core system, primary and secondary control rod system, reactor instrumentation, reactor vessel and closure head, and supporting test programs. (DG)

1975-11-13

135

FFTF reactor assembly system technology  

International Nuclear Information System (INIS)

An overview is presented of the FFTF reactor and plant together with descriptions of core components, core internals, core system, primary and secondary control rod system, reactor instrumentation, reactor vessel and closure head, and supporting test programs.

1976-03-13

136

Bypass Flow and Hot Spot Analysis for PMR200 Block-Core Design with Core Restraint Mechanism  

Energy Technology Data Exchange (ETDEWEB)

The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the ...

2009-10-15

137

Bypass Flow and Hot Spot Analysis for PMR200 Block-Core Design with Core Restraint Mechanism  

International Nuclear Information System (INIS)

The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the ...

2009-10-01

138

Population development of Callosobruchus chinensis (L.) and their mortality by gamma radiation in different packaging materials  

International Nuclear Information System (INIS)

The development of Callossobruchus chinensis (L.) in different packaging materials were conducted with gram and lentil seeds under control temperature. The highest population rise was recorded in laminated jute bags and the weight loss of gram increased with the increase of the number of insects. A doses of 0.1 kGy inhibit all metamorphic stages of the beetle. The use of appropriate packaging materials can reduce the risk of re infestation in the post-irradiated food items. 9 refs., 1 fig., 2 tables (author).

139

Peculiarities of crack propagation in laminated composite materials and their influence on resilience absorbed energy  

International Nuclear Information System (INIS)

Presented are the results of the investigation of the kinetics and micromechanism of the failure in impact bending of oriented-crystallized specimens having the eutectic composition Ni_3Al-Ni_3Nb and of the bimetal composed of 45 steel + M3 copper. The failure kinetics was studied by high-speed filming, whereas the fractures were studied by electron fractography. The particularities of the failure of the laminar-type composite materials were found. Analyzed was the effect of the kinetic factors and the mechanism of failure upon its energy consumption.

140

Sediment trap fluxes and benthic recycling of organic carbon, polycyclic aromatic hydrocarbons, and polychlorobiphenyl congeners in Lake Superior  

Energy Technology Data Exchange (ETDEWEB)

Sediment trap fluxes of solids, organic carbon, polycyclic aromatic hydrocarbons (PAHs), and polychlorinated biphenyls (PCBs) were measured in Lake Superior in 1984 and 1985. Mass fluxes from surface waters ranged from 0.14 to 1.1 g/m{sup 2}{center dot}day and increased near the lake floor due to resuspension of surficial sediment and horizontal transport in the benthic nepheloid layer. Organic matter fluxes from surface water ranged from 60 to 90 mg of C/m{sup 2}{center dot}day, with {approximately}5% of organic carbon settling from surface waters accumulating in bottom sediments. Concentrations of PCBs and PAHs are enriched 10-100 times on settling particles relative to those on suspended particles. Resultant settling fluxes are 10-100 times greater for several PCB and PAH compounds than net accumulation rates in bottom sediments, indicating the effective and rapid recycling in the benthic region. ...

1991-03-01

141

Long-lived radionuclides in the coastal sediments of the Irish Sea, UK  

Energy Technology Data Exchange (ETDEWEB)

Over the last four decades the Irish Sea has received controlled discharges of radioactive effluents from the Sellafield (Windscale) nuclear fuel reprocessing plant in Cumbria, UK. Enhanced levels of a range of fission, activation and transuranic elements have been reported in a variety of environmental media. Most of the {sup 239,240}Pu and {sup 241}Am and about 10% of the {sup 137}Cs have been retained in a deposit of the fine sediment near the discharge point. The quantities of radionuclides discharged annually from Sellafield decreased by two orders of magnitude from the mid-1970s to 1990, but estimated critical group internal and external exposure decreased by less than one order of magnitude over this period. Redistribution of the contaminated marine sediment is potentially of major significance. In this paper, a review is presented of published work and recent our study relating to Sellafield waste long-lived radionuclides, especially ...

1996-12-01

142

Assessment of cadmium in aquatic sediment using dialysis samplers with ion-exchange-resin collection  

Energy Technology Data Exchange (ETDEWEB)

Simultaneously extracted metals (SEM) and acid volatile sulfide (AVS) show the potential for toxicity on the basis of their ratio. Accordingly, the authors spiked cadmium in a range for which Cd/AVS ratios were from 0.2 to 10 in the sediment with its weight about 8 kg in each batch. Dialysis samplers with a cation ion-exchange resin (Dowex 50W-X4) collection were used in a laboratory for the determination of free cadmium concentrations in pore water of the collected sediment. When equilibrium was reached among cadmium in pore water, sediment, and ion-exchange resin, cadmium exchanged onto resin phase was regenerated with 1 N hydrochloric acid (OPTIMA grade) and determined using an atomic absorption spectrophotometer (Zeeman 5000) with a graphite furnace accessory. Cadmium determined using the dialysis sampler is considered as free cadmium which is related to the metal bioavailability toward aquatic biota. The developed ...

1998-05-01

143

Radionuclide Distribution Coefficients for Sediments Collected from Borehole 299-E17-21: Final Report for Subtask 1a  

Energy Technology Data Exchange (ETDEWEB)

Over 360 distribution coefficients (KJ for cesium, iodine, selenium, Strontium, technetium, and uranium were measured in fiscal year 1998 using 20 sediments collected fkom borehole 299-El 7-21 on the Hanford Site as part of the Immobilized Low-Activity Waste-Performance Assessment (ILAW-PA). Additionally, the pH and cation-exchange capacity (a measure of the total quantity of cations that a sediment can adsorb) of these sediment samples were measured. The sediment samples originated from the Hanford formation (informal name). Statistical analyses, using Student's t-test and correlation were conducted with the measured values. There were no significant differences between layers 1 and 2 for the selenium, strontium, technetium, and uranium & values (statistics could not be applied to evaluate layer 3 &values). Significant differences between the cesium and iodine&values for layem 1 ...

1998-10-14

144

Stellar evolution. II - The evolution of a 3 sun-mass star from the main sequence through core helium burning.  

Science.gov (United States)

Three Sun-mass star evolution from main sequence to helium exhaustion in core, noting chronology of

1965-01-01

145

Recriticality of a BWR core during reflood after control blade meltdown  

Energy Technology Data Exchange (ETDEWEB)

In nuclear reactor safety research, the question of the possible consequences of delayed core reflood during severe accidents or anticipated transient without scram transients in boiling water reactors (BWRs) has been raised. One can envisage a very low probability accident scenario leading to core uncovery and core heat-up, followed by control blade melting and subsequential delayed reflooding of the core with unborated water before its degradation. Reflooding of the hot core causes significant increases in the peak heating, melting, and hydrogen production rates, thus increasing the probability of core degradation. However, as has been established, debris beds formed from shattered fuel rods and quenched fuel melt will be undermoderated. The reflood process of a voided, intact core was examined using the TRAC/BFI CODE.

1994-12-31

146

Magnetic braking of the rotation of molecular cloud cores  

International Nuclear Information System (INIS)

We investigate the magnetic braking of the core of an axisymmetric cloud whose rotation axis is parallel to the mean direction of the magnetic field. (author).

147

Characterizing Differential Air-Core Eddy Current Probes  

Science.gov (United States)

... Accession Number : ADD331250. Title : Characterizing Differential Air-Core Eddy Current Probes. Corporate Author : Personal ...

148

Dual radiotracer measurement of zoobenthos-mediated solute and particle transport in freshwater sediments  

International Nuclear Information System (INIS)

#gamma# spectroscopy methods have been applied to determine the effects of two freshwater benthic macroinvertebrates, on reworking of sediments and the transfer of solutes across the sediment-water interface. Natural lake sediments and overlying water were contained in temperature-regulated rectangular plastic cells. After addition of Stylodrilus (oligochaete worms) and Pontoporeia (crustacean amphipods) to these microcosms, the vertical distribution of Cs-137 (a tracer of particle transport) and Na-22 (a tracer of solute transport) were determined. In cells with Stylodrilus, the Cs-137 layer moved downward at a rate that decreased exponentially with time. In cells with Pontoporeia, Cs-137 activity was smeared downward in time owing to eddy diffusive mixing of sediments over a small range (1-2 cm). In cells without worms, the veneer of Cs active material remained at the interface while the penetration ...

149

Carcinogenicity of Black Rock Harbor sediment to the eastern oyster and trophic transfer of Black Rock Harbor carcinogens from the blue mussel to the winter flounder  

Energy Technology Data Exchange (ETDEWEB)

The eastern oyster (Crassostrea virginica) developed neoplastic disorders when experimentally exposed both in the laboratory and field to chemically contaminated sediment from Black Rock Harbor (BRH), Bridgeport, Connecticut. Neoplasia was observed in oysters after 30 or 60 days of continuous exposure in a laboratory flow-through system to a 20 mg/L suspension of BRH sediment plus postexposure periods of 3, 30, or 60 days. Composite tumor incidence was 13.6% for both exposures. Tumor occurrence was highest in the renal excretory epithelium, followed in order by gill, gonad, gastrointestinal, heart, and embryonic neural tissue. Regression of experimental neoplasia was not observed when the stimulus was discontinued. In field experiments, gill neoplasms developed in oysters, deployed in cages for 30 days at BRH and 36 days at a BRH dredge material disposal area in Central Long Island Sound, and kidney and gastrointestinal neoplasms developed in ...

1991-01-01

150

Analysis of Elements in The Baltic Sea Sediment by Using Gamma Spectrometry  

International Nuclear Information System (INIS)

We have done analysis of elements in the Baltic sea sediment by using gamma spectrometry in neutron activation analysis Goal of the analysis is to determine the rate of morsel elements which is contained in the Baltic sea sediment. Sample of the Baltic sea Sediment (IAEA-SED-1), Standard of Reference Material (SRM) 1646 Estuarine Sediment and Standard Ce, Fe, Sc, and Co are put into vial of capsule rabbit, then irradiated together for 30 minutes in rabbit facility Multi Purpose Reactor at power of 25 MW and then cooled for one week. Next sample, standard, and SRM which have irradiated, each is cut for 30 minutes using gamma spectrometer. Result of analysis of rate of elements Ce, Fe, Sc and Co in the baltic sea sediment successively equal to 141.20 ppm, 5.91 %, 14.88 ppm, and 19.59 ppm. Result of analysis in SRM Estuarine sediment successively equal to 96.60 ...

2007-04-01

151

Sedimentation of the Enan suite of the lower to middle Jurassic and coal reserves of the southeastern margin of the Ordos basin (China)  

Energy Technology Data Exchange (ETDEWEB)

The studied coal bearing series has a parallel origin. The following facial complexes are isolated in its composition: lakes free of vegetation without coal interlayers; overgrown lakes of their margins which are poor in coals; swampy lakes, whose peat beds formed coal layers of shallow or moderate depth; channel sediments without coal layers and swamps from between channel spaces which created thick coal strata of high quality for which, however, a strong changeability in thickness is intrinsic. The coal strata are normally split towards the central parts of the lake basins and river channels. The coal presence of the suite is reduced along the section which is associated with the replacement of the lake swamp conditions of sedimentation by lake river conditions. A paleotectonic analysis established that the distribution of the zones richest in coal was controlled by consedimentational structural elements.

1983-01-01

152

Rio Grande sediment study -- Supply and transport  

Energy Technology Data Exchange (ETDEWEB)

The 1992 New Mexico State Legislature directed the Interstate Stream Commission (ISC) to study the feasibility of clearing and deepening the channel of the Rio Grande between Albuquerque and Elephant Butte to improve water conveyance and water conservation. The ISC requested the US Army Corps of Engineers-Albuquerque District (COE) to undertake this study under the Planning Assistance to States Program. The study was divided into two phases. Phase 1 consisted of an analysis of the sediment contribution to the Rio grande from the tributaries and an evaluation of the existing US Geological Survey (USGS) sediment gage data. Phase 2 will be an analysis, through the use of an HEC-6, Scour and Deposition in Rivers and Reservoirs, computer model, to determine the long-term performance of any Rio Grande channel improvements. This narrative presents the Phase 1 methods and results.

1995-12-31

153

Relationship between the lability of sediment-bound metals (Cd, Cu, Zn) and their bioaccumulation in benthic invertebrates  

British Library Electronic Table of Contents (United Kingdom)

The present study has investigated metal contamination at nine sites (10 sampling stations) from the English Channel to the Mediterranean Sea, including low level and highly contaminated sediments. Both total and labile concentrations of metals were determined in superficial sediments. The influence of different pHs was tested and metal lability at pHs encountered in the gut of invertebrates (the ragworm Nereis diversicolor, the blue mussel Mytilus edulis, the Japanese oyster Crassostrea gigas) was compared with the distribution of metals in various operationally defined geochemical fractions. Cd showed the highest lability and Cu the lowest, whereas Zn lability was intermediate. Metal concentrations were determined in bivalves at six sites and in worms at three sites. Cd in living organis...

2007-01-01

154

Quantifying bank erosion on the South River from 1937 to 2005, and its importance in assessing Hg contamination  

British Library Electronic Table of Contents (United Kingdom)

Bank sediments along a 40km reach of the South River, downstream of Waynesboro, VA, store mercury from historical contamination as a result of textile manufacturing. Knowledge of the rate at which contaminated sediment is released to the stream channel through bank erosion is required to implement restoration programs designed, for example, to minimize its ecological impact and to reduce risk to human health. Digitized stream channel boundaries based on visual interpretations of georeferenced aerial imagery from 1937 and 2005 were compared to calculate a minimum estimate of the total area of bank sediment eroded between Waynesboro and Port Republic, Virginia. Estimates of riverbank height were extracted from aerial LIDAR data, allowing areal estimates of bank retreat to be converted to vol...

2009-01-01

155

Oxygen dynamics in periphyton communities and associated effects on phosphorus release from lake sediments  

Energy Technology Data Exchange (ETDEWEB)

Periphyton is typically a heterogeneous assemblage of filamentous and single celled photoautotrophic and heterotrophic micoorganisms suspended in a mucopolysaccharide matrix which they produce. By definition, the assemblage is attached to a substratum such as rock, sediment, or plant in an aquatic environment. Microtechniques with high spatial and temporal resolution are required to define metabolic interactions among the heterotrophic and autotrophic constituents, and between periphyton and its environment. This study used oxygen sensitive microelectrodes with tip diameters of < 30 m to investigate the effects of photosynthesis and respiration on the oxygen dynamics of several diverse periphyton communities both in situ and in laboratory microcosms. A novel flow-through system that utilized TSP radiotracer and that permitted manipulation of the velocity, flushing rate, and oxygen concentration of overlying water was developed to investigate the role of ...

1986-01-01

156

NONLINEAR OPTICAL PHENOMENA: Nonlinear optical properties of colloidal silver nanoparticles produced by laser ablation in liquids  

Science.gov (United States)

The optical and nonlinear optical properties of colloidal solutions of silver obtained by laser ablation in water and ethanol are studied. It is shown that freshly prepared colloids experience a full or partial sedimentation by changing their nonlinear optical properties. Aqueous colloids undergo a partial sedimentation and their nonlinear optical absorption changes to nonlinear optical transmission. The obtained results are interpreted using the Drude model for metal particles taking the particle size into account and can be explained by the sedimentation of larger silver particles accompanied by the formation of a stable colloid containing silver nanoparticles with a tentatively silver oxide shell. The characteristic size of particles forming such a stable colloid is determined and its optical nonlinearity is estimated.

2004-07-01

157

Deep-sea mud in the Pacific Ocean as a potential resource for rare-earth elements  

British Library Electronic Table of Contents (United Kingdom)

World demand for rare-earth elements and the metal yttrium?which are crucial for novel electronic equipment and green-energy technologies?is increasing rapidly. Several types of seafloor sediment harbour high concentrations of these elements. However, seafloor sediments have not been regarded as a rare-earth element and yttrium resource, because data on the spatial distribution of these deposits are insufficient. Here, we report measurements of the elemental composition of over 2,000 seafloor sediments, sampled at depth intervals of around one metre, at 78 sites that cover a large part of the Pacific Ocean. We show that deep-sea mud contains high concentrations of rare-earth elements and yttrium at numerous sites throughout the eastern South and central North Pacific. We estimate that an a...

2011-01-01

158

Concentration of radiocaesium {sup 137}Cs and {sup 134}Cs in sediments of the Malaysian marine environment  

Energy Technology Data Exchange (ETDEWEB)

The concentrations of {sup 137}Cs and {sup 134}Cs in Malaysian marine sediments were measured by gamma-ray spectrometry with a high-purity germanium (HPGe) detector connected to a multichannel analyzer. In general, the {sup 137}Cs concentration in Malaysian marine sediments has been found to be very low and less than 5 Bq/kg dry weight with the exception of those from a few sampling locations. The concentration of {sup 134}Cs was found to be less than the minimum detectable activity for the measuring condition used. Data reported in this paper were found to be comparable with results from within the region and thus can be used as reference data for the country.

2007-12-15

159

Chaotic characters of the Yellow River Basin based on the sediment time series: An attempt to integrated research in geography  

British Library Electronic Table of Contents (United Kingdom)

The sediment content of the Yellow River is resulted from the interactions of natural, economic, and social factors, so it includes some evolutive information of the Yellow River Basin system. Sediment contents from 1952 to 2007 on Toudaoguai, Tongguan, Huayuankou and Lijin sections along the river are chosen as the study time series, and correlation dimensions (D 2), Kolmogorov entropies (K 2), and Hurst indexes (H) of the time series were calculated. Correlation dimensions on Toudaoguai, Tongguan, Huayuankou, and Lijin sections are 3.24, 5.69, 6.57 and 7.34 respectively, and the Kolmogorov entropies are 0.13, 0.37, 0.40 and 0.38 respectively, which indicates that the systems controlled by different sections along the Yellow River are chaotic systems and the chaotic degrees increase gradu...

2010-01-01

163

Dynamical evolution and molecular abundances of interstellar clouds  

International Nuclear Information System (INIS)

Dynamical models are presented that start with interstellar gas in an initial diffuse state and consider their gravitational collapse and the formation of dense cores. Frozen-in tangled magnetic fields are included to mimic forces that might oppose gravitational contraction and whose effectiveness may increase with increasing core densities. Results suggest the possibility that dense cloud cores may be dynamically evolving ephemeral objects, such that their lifespan at a given core density decreases as that density increases. 66 refs.

164

Comparison of calculated and measured irradiated wire data for HEU and mixed HEU/LEU cores in the ORR (Oak Ridge Research Reactor)  

Energy Technology Data Exchange (ETDEWEB)

Low power wire activations are being performed in the Oak Ridge Research Reactor (ORR) as part of the whole-core LEU demonstration experiments. Calculations of the demonstration cores, including simulation of the wire activations, are being performed at Argonne National Laboratory (ANL). This paper presents the results of comparisons for 293 wires from five cores and shows that, on the average, the integrated activities agree within 6%.

1986-01-01

165

Viscosity of the Earth's inner core: Constraints from nutation observations  

British Library Electronic Table of Contents (United Kingdom)

The gravitational torque applied on the Earth by the other celestial bodies generates periodic variations in the orientation of the Earth's rotation axis in space which are called nutations. Observations of Earth's nutations allow for insights into the physical properties of the inner core because of the presence of a normal mode, the Free Inner Core Nutation (FICN), which is characterized by a tilt of the inner core figure and rotation axes with respect to the mantle and outer core. The frequency of the FICN is controlled by the strength of the mechanical coupling acting at the inner core boundary (ICB) and by the ability of the inner core to deform under the action of centrifugal and gravitational forces. Attenuation of the FICN reflects energy dissipated by electromagnetic (EM) and visc...

2011-01-01

166

A comparative design study of PB-BI cooled reactor cores with forced and natural convection cooling  

International Nuclear Information System (INIS)

A comparative core design study is performed on Pb-Bi cooled reactors with forced and natural convection (FC and NC) cooling. Major interests of the study are core performance and core safety features. The designed core concepts with nitride fuel achieve reasonable breeding capability. The results of unprotected event analyses such as UTOP and ULOF show that both of concepts have possible features to withstand unprotected events due to negative reactivity feedback by Doppler effect, control rod drive line expansion, etc. These results lead to a conclusion that both of concepts have possible capability as one of future promising core concepts. A FC cooling core concept has more advantage if fuel recycle viewpoint is emphasized. (author)

2003-04-20

167

Toxic chemicals, including aromatic and chlorinated hydrocarbons and their derivatives, and liver lesions in white croaker (Genyonemus lineatus) from the vicinity of Los Angeles  

Energy Technology Data Exchange (ETDEWEB)

High concentrations of toxic chemicals in sediment and white croaker (Genyonemus lineatus), as well as liver diseases (e.g., carcinomas) in this species, were found in the Los Angeles area. The highest concentrations of aromatic hydrocarbons (AHs) in the sediment were in San Pedro Bay, and the highest concentrations of 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) derivatives were in sediment from near the White Point sewer outfall. Concentrations of AHs, polychlorobiphenyls (PCBs), and DDT derivatives were generally higher in food organisms from the croaker's stomach than in sediment. Moreover, croaker from San Pedro Bay and White Point were substantially contaminated with DDT derivatives and metabolites of aromatic compounds, compared to croaker from the Hyperion outfall and Dana Point. The evidence suggest that the observed pathological conditions of the liver were associated with ...

1987-08-01

168

The chemistry of hydrothermal mounds near the Galapagos Rift  

Science.gov (United States)

Samples dredged from the sediment mounds have a unique chemistry and mineralogy which reveals details of the hydrothermal processes that produce these deposits. The mounds form primarily by deposition of Fe, Mn and Si from hydrothermal fluids which circulate through the basalt crust and the overlying sediments. The Mn, Fe and Si are strongly fractionated in the process; the Fe and Si precipitate within the mounds under slightly reducing conditions as nontronite, while the Mn is deposited as Mn oxyhydroxides at the seawater-sediment interface. The nontronite is exceptionally well crystallized, and contains less than 200 ppm Al. The Mn minerals, todorokite and birnessite, also have exceptional crystallinity and the distribution of trace elements Cu, Ni, Zn, Co, Ca and Ba in these phases agrees with predictions made on the basis of models of their crystal structure. The environment of deposition which produces this suite of ...

1978-06-01

169

The Potential Use of Electricity to Control Burrowing Shrimp in Oyster Aquaculture Beds  

Science.gov (United States)

Thalassinid shrimp cause significant problems for oyster aquaculture in the Pacific Northwest (USA) where oysters succumb to the physical disruption of the sediment by the burrowing activity of these animals. While electrofishing is a commonly used technique to capture fish and some invertebrates i...

170

Superfund record of decision (EPA Region 2): Burnt Fly Bog, Marlboro Township, NJ, September 30, 1998  

Energy Technology Data Exchange (ETDEWEB)

This decision document presents the selected remedial action for the Westerly Wetlands, Northerly Wetlands, and Tar Patch Area at the Burnt Fly Bog Superfund Site. It addresses contaminated soil present on the three remaining contaminated areas on the Site, including the Westerly Wetlands, Northerly Wetlands, and Tar Patch Area. The major components of the selected remedy include: Excavation and off-site disposal of contaminated soil from the Northerly Wetlands; Excavation and off-site disposal of contaminated soil from the Tar Patch Area; Backfilling the excavated area in the Northerly Wetland and reestablishing wetlands; Backfilling the excavated area in the Tar Patch Area and creating wetlands; Provision of additional security fencing around the Westerly Wetlands, and the recording of a Deed Notice for the Westerly Wetlands, Northerly Wetlands, and Tar Patch Area; Monitoring of surface water and sediment in the Westerly Wetlands, surface water and ...

1999-03-01

171

Sediments transport and balance in coastal line; Trasporto solido ed equiliberio della linea di costa  

Energy Technology Data Exchange (ETDEWEB)

The erosion phenomena of coastal regions in Italy and in the world is remarkable from the environmental point of view. Are showed activities of mechanical defense and numerical models to solve complex problem.

1996-11-01

172

Risks of consumption of contaminated seafood: the Quincy Bay case study.  

UK PubMed Central (United Kingdom)

A recent EPA-sponsored study of sediment and seafood contamination in Quincy Bay revealed elevated levels of several complex organic pollutants frequently of concern in human health assessments. A seafood...Full Text Available

1991-01-01

173

Reduction of Selenate to Selenide by Sulfate-Respiring Bacteria: Experiments with Cell Suspensions and Estuarine Sediments  

UK PubMed Central (United Kingdom)

Washed cell suspensions of Desulfovibrio desulfuricans subsp. aestuarii were capable of reducing nanomolar levels of selenate to selenide as well as sulfate to sulfide....Full Text Available

1987-06-01

174

Polycyclic Musks in Water, Sediment, and Fishes from the Upper Hudson River, New York, USA  

British Library Electronic Table of Contents (United Kingdom)

Synthetic musks are used in many consumer products for their pleasant odor and their binding affinity for fabrics. In the early 1990s, polycyclic musks were reported to occur in air, water, sediment, wildlife, and humans from many European countries. Concentrations of polycyclic musks, particularly 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethyl-cyclopenta-[?]-2-benzopyr an (HHCB) and 7-acetyl-1,1,3,4,4,6-hexamethyl-1,2,3,4-tetrahydronapthalene (AHTN), have been reported to increase over time in the environment. In this study, concentrations of musks in water, sediment, fish, and mussel were determined from three locations along the upper Hudson River. HHCB and AHTN were detected in water (n?=?5; 3.95?25.8 and 5.09?22.8?ng/L, respectively), sediment (n?=?3; 72.8?388 and 113?544?ng/g, dry weig...

2011-01-01

175

Nitrogen Cycling and Community Structure of Proteobacterial ?-Subgroup Ammonia-Oxidizing Bacteria within Polluted Marine Fish Farm Sediments  

UK PubMed Central (United Kingdom)

A multidisciplinary approach was used to study the effects of pollution from a marine fish farm on nitrification rates and on the community structure of ammonia-oxidizing bacteria in the underlying...Full Text Available

1999-01-01

176

New Species of the Late Cenozoic Fungal form-Genus Mediaverrunites Jarzen & Elsik 1986 Ex Nandi & Sinha 2007  

Science.gov (United States)

... Wrenn. References CitedBanerjee, S., and Nandi, B. 1992 Fossil fungi from Miocene sediments of Mizoram and their environmental ... ...

177

Name of Presentation!  

Wastenet

Up-flow anaerobic attached-growth bioreactors filled with pre-treated coir fibres ...coir-fibre arranged in bottle-brush configuration bounded by a novel plastic binding technique ...-three anaerobic filter reactors in series -coir fibre as the bacteria growth media a sedimentation

178

Intracellular ribonucleoprotein complexes of visna virus are infectious.  

UK PubMed Central (United Kingdom)

Sheep choroid plexus cells infected with visna virus produce intracytoplasmic viral ribonucleoprotein complexes with sedimentation values of 120S to 200S and buoyant densities of 1.29 to 1.32 g/cm3....Full Text Available

1982-06-01

179

Insights into the Genome of Large Sulfur Bacteria Revealed by Analysis of Single Filaments  

UK PubMed Central (United Kingdom)

Marine sediments are frequently covered by mats of the filamentous Beggiatoa and other large nitrate-storing bacteria that oxidize hydrogen sulfide using either oxygen or nitrate, which...Full Text Available

2007-09-01

180

Heavy metals in Semarang`s urban streams: Spatial distribution and bioindication using the guppy (Lepistes reticulatus)  

Energy Technology Data Exchange (ETDEWEB)

A field survey on cadmium, lead, copper, and zinc was performed in Semarang, the fifth largest city in Indonesia. Water, sediment, and fish samples were collected from 101 grids of 2 x 2 km. The objectives of the study were (1) to identify the spatial distribution of metals in the sediments of the greater Semarang area, (2) to estimate the background concentrations of the metals present in Semarang, (3) to provide a simple tool for deriving standards for metals in the sediment, and (4) to explore the potential use of the guppy (Lebistes reticulatus) as a bioindicator of urban metal pollution. To map the spatial distribution of the metals, concentrations of each metal in sediment were plotted against the corresponding city coordinate. On the basis of these plots, background concentrations of the metals were estimated. A combined pollution index can be derived thereafter by calculating the difference ...

1996-12-31

181

Geologic setting of the New Production Reactor within the Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

The geology and hydrology of the reference New Production Reactor (NPR) site at Savannah River Site (SRS) have been summarized using the available information from the NPR site and areas adjacent to the site, particularly the away from reactor spent fuel storage site (AFR site). Lithologic and geophysical logs from wells drilled near the NPR site do not indicate any faults in the upper several hundred feet of the Coastal Plain sediments. However, the Pen Branch Fault is located about 1 mile south of the site and extends into the upper 100 ft of the Coastal Plain sequence. Subsurface voids, resulting from the dissolution of calcareous portions of the sediments, may be present within 200 ft of the surface at the NPR site. The water table is located within 30 to 70 ft of the surface. The NPR site is located on a groundwater divide, and groundwater flow for the shallowest hydraulic zones is predominantly toward local streams. Groundwater flow in ...

1991-12-31

182

Functional Exoenzymes as Indicators of Metabolically Active Bacteria in 124,000-Year-Old Sapropel Layers of the Eastern Mediterranean Sea  

UK PubMed Central (United Kingdom)

Hydrolytic exoenzymes as indicators of metabolically active bacteria were investigated in four consecutive sapropel layers collected from bathyal sediments of the eastern Mediterranean Sea. For comparison,...Full Text Available

2000-06-01

183

Contaminated Site Clean-Up Information (CLU-IN): Providing information...  

Science.gov (United States)

/Stabilization Nov 16: NARPM Presents...In Situ Sediment Remediation Using Benthic Waterjet Amendment Placement Nov 17: Use of Risk Assessment in Management of Contaminated...

2011-10-08

184

Characterization of T-Even Bacteriophage Substructures  

UK PubMed Central (United Kingdom)

Tail plates obtained from T4D amber mutants were examined with respect to sedimentation behavior, subunit molecular weights, amino acid composition, isoelectric points, and morphology. Intact plates...Full Text Available

1970-10-01

185

Antibacterial Colorants: Characterization of Prodiginines and Their Applications on Textile Materials  

UK PubMed Central (United Kingdom)

A strain of Vibrio sp. isolated from marine sediments produced large quantities of bright red pigments that could be used to dye many fibers including wool, nylon, acrylics,...Full Text Available

2008-05-01

186

Analysis on depositional system and discussion on ore-formation conditions of channel sandstone type uranium deposit. Taking Dongsheng area, Ordos meso-cenozoic basin as an example  

International Nuclear Information System (INIS)

Applying the theory of depositional system, the depositional facies and depositional systems of the Zhiluo Formation in Dongsheng area are systematically analysed, and the authors proposed that sediments of the Zhiluo Formation are of fluvial facies, and streams of the Zhiluo time experienced three evolution stages, namely: the early braided stream, the middle low sinuosity meandering stream and the late high sinuosity meandering stream. Based on features of paleoclimatic evolution, the Zhiluo Formation is divided into two lithological members. The lower lithological member consists of sediments of braided and low sinuosity meandering streams under humid-ward paleoclimatic conditions forming grey sedimentary formation. The upper member is composed of sediments of meandering streams under arid-hot paleoclimatic conditions representing complex-colored (mainly red) sedimentary formation. It is suggested that uranium ...

2003-03-01

187

A 1500-year record of lead, copper, arsenic, cadmium, zinc level in Antarctic seal hairs and sediments  

Energy Technology Data Exchange (ETDEWEB)

To reconstruct the profiles of heavy metal levels in the South Ocean ecosystem of Antarctica, the concentrations of lead (Pb), copper (Cu), arsenic (As), cadmium (Cd), and zinc (Zn) in seal hairs and lake sediments spanning the past 1500 years from Fildes Peninsula of King George Island and in weathering lake sediments from Nelson Island of West Antarctica were determined. The lead contents in the seal hairs and the weathering sediments show a sharp increase since the late 1800s, very likely due to anthropogenic contamination from modern industries. After the 1980s, the Pb content in seal hairs dropped by one-third, apparently due to the reduced usage of leaded gasoline in the Southern Hemisphere. Copper arises mainly from the weathering process, and its level may be substantially affected by climatic conditions. The concentrations of Cd, As, and Zn do not show any clear temporal trends.

2006-12-01

188

The river Elbe. A case study for the ecological and economical chain of sediments  

Energy Technology Data Exchange (ETDEWEB)

Industrial activities in the river basin of the Elbe have a very long tradition, and have been resulting in the contamination of sediments for centuries. Contamination lasted until the fall of the iron curtain; since then, the situation has improved significantly. In the transition zone between freshwater systems and the marine environment, ports like Hamburg still have to bear this burden of history. An overall (contaminated) management strategy should be developed in the context of the European Water Framework Directive with the emphasis on source control. (orig.)

2002-07-01

189

Inter-comparison of some environmental radioactivity monitoring items for Guangdong Daya Bay Nuclear Power Plant  

International Nuclear Information System (INIS)

This paper introduces the inter-comparison results of some environmental radioactivity monitoring items for Daya Bay nuclear power plant. The inter-comparison was organized by China Institute for Radiation Protection and five laboratories participated in it. The compared items included total #beta# in kelp and sediment, "3H in water, "9"0Sr in soil, artificial nuclides "1"1"0"mAg, "2"4"1Am, "1"0"9Cd, "5"7Co in kelp and sediment. Inter-comparison results are analyzed as well

2003-01-01

190

Genotoxic damage in polychaetes: A study of species and cell-type sensitivities  

British Library Electronic Table of Contents (United Kingdom)

The marine environment is becoming increasingly contaminated by environmental pollutants with the potential to damage DNA, with marine sediments acting as a sink for many of these contaminants. Understanding genotoxic responses in sediment-dwelling marine organisms, such as polychaetes, is therefore of increasing importance. This study is an exploration of species-specific and cell-specific differences in cell sensitivities to DNA-damaging agents in polychaete worms, aimed at increasing fundamental knowledge of their responses to genotoxic damage. The sensitivities of coelomocytes from three polychaetes species of high ecological relevance, i.e. the lugworm Arenicola marina, the harbour ragworm Nereis diversicolor and the king ragworm Nereis virens to genotoxic damage are compared, and dif...

2008-01-01

191

Activity concentration of some anthropogenic radionuclides in the surface marine sediments near the Saudi coast of the Arabian (Persian) Gulf  

British Library Electronic Table of Contents (United Kingdom)

Activity concentrations of some anthropogenic radionuclides (90Sr, 137Cs, 238Pu, 239+240Pu and 241Am) have been measured in the surface of marine sediments along the Saudi coast of the Arabian (Persian) Gulf. The samples were collected at different locations and water depths. The spatial distribution of the concentrations of the measured radionuclides showed a heterogeneous pattern and is independent of location or water depth. The obtained results are discussed and some conclusions are drawn.

2007-01-01

192

WASTE TREATMENT AND DISPOSAL PROGRESS REPORT FOR JUNE AND JULY 1962  

Science.gov (United States)

9 9 simulated Purex waste oxides was investigated as a function of Na/sub 2/O, CaO and P/sub 2/O/sub 5/ content. All compositions lost some sulfate at 50 to 100 deg C above the softening point. In generai the volatility decreased with increase of either Na/ sub 2/O or CaO relative to P/sub 2/O/sub 5/, but no simple correlation Was indicated. Softening temperatures were lowered by inc ease in Na/sub 2/O vs CaO. Ceramic solids were obtained but no true glasses. Attempts to produce glasses by addition of varying combinations of Al/sub 2/O/sub 3/, PbO, BaO, and B/sub 2/O/ sub 3/ to simulated Pure x waste plus phosphite were unsuccessful. The use of 0.005 M Na/sub 2/C/O/sub 3/ to precipitate calcium from wastes containing up to 3 ppm of phosphate was demonstrated in four pilot plant runs and produced a decrease in the hardness of the waste leaving the clarifier. An inadvertent Sr/ sup 90/ and Cs/sup 137/ breakthrough occurred during one run which was caused ...

1962-12-19

193

Distribution of polycyclic aromatic hydrocarbons in water and surface sediments from Daya Bay, China  

International Nuclear Information System (INIS)

Findings indicate an urgent need to establish a monitoring program for persistent organic pollutants in water and sediment. - Marine culture is thriving in China and represents a major component of the regional economy in coastal zones, yet the environmental quality of many of those areas has never been studied. This paper attempts to investigate the quality status of Daya Bay, a key aquaculture area in China. The levels of 16 polycyclic aromatic hydrocarbons (PAHs) were determined in water and sediment samples of the bay. The total concentrations of 16 PAHs varied from 4228 to 29325 ng l"-"1 in water, and from 115 to 1134 ng g"-"1 dry weight in sediments. In comparison to many other marine systems studied, the PAH levels in Daya Bay waters were relatively high, and at six sites they were sufficiently high (>10 #mu#g l"-"1) to cause acute toxicity. The PAH composition pattern in sediments suggest ...

2003-02-01

194

Energy-filtered electron microscopy for imaging core-shell nanostructures  

Energy Technology Data Exchange (ETDEWEB)

CuAg core-shell nanoparticles are synthesized by ultra-high vacuum thermal evaporation. We show on this system how the Energy-Filtered Transmission Electron Microscopy (EFTEM) technique allows one to improve the characterization by precisely pointing out the formation of core-shell arrangements in bimetallic nanoparticle assemblies. A criterion to measure the shell thickness from EFTEM images on unique core-shell nanoparticles is defined, that can be used for core-shell nanoparticles of any sizes, with shell thicknesses over 1 nm. It is based on the intensity variation along a line drawn across a core-shell nanoparticle on a EFTEM image. This criterion has been validated by a close comparison of the shell thickness measurements performed in this work and the ones obtained by acoustic micro-Raman spectroscopy. Using this criterion, we report a strong correlation between the size of ...

2008-08-15

195

Emergency reactor core cooling device  

International Nuclear Information System (INIS)

The device of the present invention improves reactor safety by suppressing lowering of water level in a shroud which surrounds a reactor core, even upon occurrence of rupture of pipelines in an emergency reactor core cooling system in a recycling pump-incorporated type reactor. Namely, an opening of each of cooling systems which forms the emergency reactor core cooling device in a reactor pressure vessel is disposed above the upper end of the reactor core. Further, it also comprises an independent high pressure water injection system, gravitational dropping type water injection system and an automatic depressurization system. With such a constitution, even if rupture of pipelines in the system should be assumed, coolants never flow directly from the shroud which surrounds the reactor core. In addition, there are no pipelines to be ruptured below the upper end of the reactor ...

1993-03-16

196

Weather ability studies of phenolic resin coated woods and glass fiber reinforced laminates  

International Nuclear Information System (INIS)

Phenolic resins have made a major breakthrough in the field of high technology in 80's. These are now active participants of "high tech' areas ranging from electronics, computers, communication, outer space, aerospace, advanced materials, bio materials and technology. A phenol - formaldehyde (1:1.5) resin having resin content of 70% synthesized in the laboratory has been applied for wood coating and reinforcing glass fiber. The weatherability and solvent resistance of these items have been studied and results discussed keeping in view the envisaged application for structural materials and chemical equipment. The toxic materials released during contact with solvents for chemical applications and during degradation general have been monitored. The results are discussed with reference to environmental pollution due to these resins and their composites under different conditions. (authors)

1997-09-01

197

Thermal conductivity of polyisocyanurate foam board insulation blown with CFC-11 substitutes: Laboratory and long-term field measurements  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on a series of laboratory and controlled test site measurements of the thermal conductivity of polyisocyanurate foam laminated boardstock roof insulations produced with several different blowing agents; CFC-11, HCFC-123, HCFC-14lb, and two blends of the HCFCs. The behavior of the experimental foams with HCFCs is compared to that of conventional polyisocyanurate foam blown with CFC-11. Thermal drift observed from two years of field exposure is compared to laboratory accelerated aging tests and the laboratory and field measurement techniques are described. This work is part of a Joint Industry/Government Project established in the United States to evaluate the technical viability of HCFC alternative blowing agents for polyisocyanurate foam roof insulations.

1992-01-01

198

The influence of electron-beam irradiation on some mechanical properties of commercial multilayer flexible packaging materials  

International Nuclear Information System (INIS)

The influence of electron-beam irradiation on mechanical properties of commercial multilayer flexible packaging materials based on coextruded and laminated polypropylene (PP), low-density polyethylene (LDPE), ethylene vinyl alcohol copolymer (EVOH) and poly(ethylene terephthalate) (PET), irradiated with doses up to 120 kGy, was studied. The tensile strength and elongation at break of the irradiated PET/PP film increase, while the penetration and sealing resistance decreased. In addition, the irradiated PET/LDPE/EVOH/LDPE film presented increase in the tensile strength on some radiation doses and decrease of the penetration and sealing resistance, except for sealing resistance at radiation dose of 15 kGy that resulted in a slight increase of ca 4%.

2008-09-21

199

Reference equilibrium core with central flux irradiation facility for Pakistan research reactor-1  

International Nuclear Information System (INIS)

In order to assess various core parameters a reference equilibrium core with Low Enriched Uranium (LEU) fuel for Pakistan Research Reactor (PARR-1) was assembled. Due to increased volume of reference core, the average neutron flux reduced as compared to the first higher power operation. To get a higher neutron flux an irradiation facility was created in centre of the reference equilibrium core where the advantage of the neutron flux peaking was taken. Various low power experiments were performed in order to evaluate control rods worth and neutron flux mapping inside the core. The neutron flux inside the central irradiation facility almost doubled. With this arrangement reactor operation time was cut down from 72 hours to 48 hours for the production of the required specific radioactivity. (author)

2008-07-01

200

Influence of substructure design and spacer settings on the in vitro performance of molar zirconia crowns  

British Library Electronic Table of Contents (United Kingdom)

Objectives: The aim of this study was to evaluate the in vitro behaviour of all-ceramic zirconia molar crowns in regard to different core designs and marginal fit. Methods: Identically shaped methacrylate molars were prepared according to the ceramic restoration directives resulting in a 1-mm deep circular shoulder preparation. They were embedded in polymethylmethacrylate resin after covering their roots with a polyether layer to simulate periodontal mobility. The crown cores were made of yttria-stabilized zirconia veneered with a corresponding veneering ceramic. The crowns were divided into 5 groups (n=8) which differed in core design and cement gap thickness: #1: simple core, 40mm cement; #2: core with minimal occlusal support, 40mm cement; #3: core with optimized cusp support, 40mm ceme...

2009-01-01

201

Core-shell polymer nanorods by a two-step template wetting process  

International Nuclear Information System (INIS)

One-dimensional core-shell polymer nanowires offer many advantages and great potential for many different applications. In this paper we introduce a highly versatile two-step template wetting process to fabricate two-component core-shell polymer nanowires with controllable shell thickness. PLLA and PMMA were chosen as model polymers to demonstrate the feasibility of this process. Solution wetting with different concentrations of polymer solutions was used to fabricate the shell layer and melt wetting was used to fill the shell with the core polymer. The shell thickness was analyzed as a function of the polymer solution concentration and viscosity, and the core-shell morphology was observed with TEM. This paper demonstrates the feasibility of fabricating polymer core-shell nanostructures using our two-step template wetting process and opens the arena for optimization and future ...

2009-07-22

202

[caCORE: core architecture of bioinformation on cancer research in America].  

Science.gov (United States)

A critical factor in the advancement of biomedical research is the ease with which data can be integrated, redistributed and analyzed both within and across domains. This paper summarizes the Biomedical Information Core Infrastructure built by National Cancer Institute Center for Bioinformatics in America (NCICB). The main product from the Core Infrastructure is caCORE--cancer Common Ontologic Reference Environment, which is the infrastructure backbone supporting data management and application development at NCICB. The paper explains the structure and function of caCORE: (1) Enterprise Vocabulary Services (EVS). They provide controlled vocabulary, dictionary and thesaurus services, and EVS produces the NCI Thesaurus and the NCI Metathesaurus; (2) The Cancer Data Standards Repository (caDSR). It provides a metadata registry for common data elements. (3) Cancer Bioinformatics Infrastructure Objects ...

2006-04-18

203

Validation of reactor core protection system  

International Nuclear Information System (INIS)

Reactor COre Protection System (RCOPS), an advanced core protection calculator system, is a digitized one which provides core protection function based on two reactor core operation parameters, Departure from Nucleate Boiling Ratio (DNBR) and Local Power Density (LPD). It generates a reactor trip signal when the core condition exceeds the DNBR or LPD design limit. It consists of four independent channels adapted a two-out-of-four trip logic. System configuration, hardware platform and an improved algorithm of the newly designed core protection calculator system are described in this paper. One channel of RCOPS was implemented as a single channel facility for this R and D project where we performed final integration software testing. To implement custom function blocks, pSET is used. Software test is performed by two methods. The first method is a 'Software ...

2008-10-13

204

THE EVOLUTION OF CLOUD CORES AND THE FORMATION OF STARS  

International Nuclear Information System (INIS)

For a number of starless cores, self-absorbed molecular line and column density observations have implied the presence of large-amplitude oscillations. We examine the consequences of these oscillations on the evolution of the cores and the interpretation of their observations. We find that the pulsation energy helps support the cores and that the dissipation of this energy can lead toward instability and star formation. In this picture, the core lifetimes are limited by the pulsation-decay timescales, dominated by non-linear mode-mode coupling, and on the order of #approx =# few x 10"5-10"6 yr. Notably, this is similar to what is required to explain the relatively low rate of conversion of cores into stars. For cores with large-amplitude oscillations, dust continuum observations may appear asymmetric or irregular. As a consequence, some of the ...

2010-09-20

205

Synthesis and characterization of thermoresponsive polyamidoamine-polyethylene glycol-poly (D, L-lactide) (PAMAM-PEG-PDLLA) core-shell nanoparticles  

UK PubMed Central (United Kingdom)

This work describes the synthesis and characterization of novel thermoresponsive highly-branched polyamidoamine-polyethylene glycol-poly (D, L-lactide) (PAMAM-PEG-PDLLA) core-shell nanoparticles....Full Text Available

2010-03-01

206

Some properties of low-mass stellar models with chemically inhomogeneous neutral-stability zones  

Energy Technology Data Exchange (ETDEWEB)

Several low-mass models with an inhomogeneous radiative core and a convective envelope are investigated, the entire core or its upper portion being treated as a zone of neutral stability. Mixing by convective overshoot will then give rise to unstable structure.

1983-03-01

207

Polyketide synthase chemistry does not direct biosynthetic divergence between 9- and 10-membered enediynes  

UK PubMed Central (United Kingdom)

Enediynes are potent antitumor antibiotics that are classified as 9- or 10-membered according to the size of the enediyne core structure. However, almost nothing is known about enediyne core biosynthesis,...Full Text Available

2010-06-22

208

Evaluation of Core Bypass Flow in the Prismatic VHTR with a Multi-block Experiment  

International Nuclear Information System (INIS)

The core of Prismatic Modular Reactor (PMR) consists of assemblies of hexagonal graphite fuel and reflector elements. The core bypass flow of Very High Temperature Reactor (VHTR) is defined as the core flow that does not pass through the coolant channels but passes through the bypass gap between fuel elements. The increase in bypass flow makes the decrease in effective coolant flow. Since the core bypass flow has a negative impact on safety and efficiency of VHTR, core bypass phenomena have to be investigated to improve the core thermal margin of VHTR. For this purpose, the international project, I-NERI project, has been carried out since 2008. I-NERI project is collaborative project that KAERI and SNU of Korea side and INL, ANL and TAMU of U.S side are involved. In order to evaluate the core bypass flow, the multicolumn and multi-layer ...

2010-10-01

209

Development of BWR core flow measurement technology using in-core neutron fluctuating signals  

Energy Technology Data Exchange (ETDEWEB)

The extensive work on the measurement technology of total and local flow rates in BWR core has been performed using in-core neutron fluctuating signals. Based on a large amount of actual data acquired from commercial BWR plants in operation, physical interpretation was discussed on the transit time of the neutron fluctuating signals. The new findings against the logical inconsistency of the transit time between the different LPRM detector positions lead to a promised core flow measurement algorithm using in-core neutron fluctuating signals. The advanced on-line core flow measurement system was developed and tested during the startup phase of the first ABWR. The measurement test results demonstrate the present core flow measurement system within the errors of 5 through 10% over the wide operating area besides the capability for the local void fraction and ...

1997-09-01

210

Computational models of stellar collapse and core-collapse supernovae  

International Nuclear Information System (INIS)

Core-collapse supernovae are among Nature's most energetic events. They mark the end of massive star evolution and pollute the interstellar medium with the life-enabling ashes of thermonuclear burning. Despite their importance for the evolution of galaxies and life in the universe, the details of the core-collapse supernova explosion mechanism remain in the dark and pose a daunting computational challenge. We outline the multi-dimensional, multi-scale, and multi-physics nature of the core-collapse supernova problem and discuss computational strategies and requirements for its solution. Specifically, we highlight the axisymmetric (2D) radiation-MHD code VULCAN/2D and present results obtained from the first full-2D angle-dependent neutrino radiation-hydrodynamics simulations of the post-core-bounce supernova evolution. We then go on to discuss the new code Zelmani which is based on the open-source HPC ...

2009-07-01

211

Bacterial Fouling in a Model Core System  

UK PubMed Central (United Kingdom)

We have used a sintered glass bead core to simulate the spaces and surfaces of reservoir rock in studies of the bacterial plugging phenomenon that affects waterflood oil recovery operations. The passage...Full Text Available

1985-03-01

212

Acetylene Reduction by Soil Cores of Maize and Sorghum in Brazil  

UK PubMed Central (United Kingdom)

Nitrogenase activity was measured by the C2H2 reduction method in large soil cores (29 cm in diameter by 20 cm in depth) of maize (Zea mays) and sorghum (Sorghum...Full Text Available

1977-03-01

213

A novel enzyme-based acidizing system: Matrix acidizing and drilling fluid damage removal  

Energy Technology Data Exchange (ETDEWEB)

A novel acidizing process is used to increase the permeability of carbonate rock cores in the laboratory and to remove drilling fluid damage from cores and wafers. Field results show the benefits of the technology as applied both to injector and producer wells.

1995-12-31

214
215

Structural Stability of a Joined-Wing Sensorcraft  

Science.gov (United States)

... core section of the composite sandwich panels (Figure 5). Table 6 shows the properties that buckled as well as their initial ...

2007-06-01

217

Moisture Ingression In Honeycomb Core Sandwich Panels: Directional Aspects  

Science.gov (United States)

Moisture ingression was studied in several composite sandwich panels.No observable ingression was

1997-01-01

218

Enhanced Core Noise Modeling for Turbofan Engines  

Science.gov (United States)

This report describes work performed by MTC Technologies (MTCT) for NASA Glenn Research Center (GRC)

2011-01-01

220

EFFECTS OF SHIELDING ON PROPERTIES OF EDDY ...  

Science.gov (United States)

... Accession Number : ADD323869. Title : EFFECTS OF SHIELDING ON PROPERTIES OF EDDY CURRENT PROBES WITH FERRITE CUP CORES. ...

1986-08-01

221

EDDY CURRENT SIZING OF CASE DEPTH IN BEARING ...  

Science.gov (United States)

... HARDENED CUP AND CARBURIZED AND HARDENED CORES HAVE BEEN PROFILED USING 2 TYPES OF EDDY CURRENT PROBES. ...

1986-07-01

222

Differential influence of instruments in nuclear core activity evaluation by data assimilation  

International Nuclear Information System (INIS)

The global neutronic activity fields of a nuclear core can be reconstructed using data assimilation. Indeed, data assimilation allows to combine both measurements from instruments and information from a model, to evaluate the best possible neutronic activity within the core. We present and apply a specific procedure which evaluates the influence of measures by adding or removing instruments in a given measurement network (possibly empty). The study of various network configurations for the instruments in the nuclear core establishes that the influence of the instruments depends both on the independent instrumentation location and on the chosen network.

2011-01-11

223

Computer control of fuel handling activities at FFTF  

International Nuclear Information System (INIS)

The Fast Flux Test Facility near Richland, Washington, utilizes computer control for reactor refueling and other related core component handling and processing tasks. The computer controlled tasks described in this paper include core component transfers within the reactor vessel, core component transfers into and out of the reactor vessel, remote duct measurements of irradiated core components, remote duct cutting, and finally, transferring irradiated components out of the reactor containment building for off-site shipments or to long term storage. 3 refs., 16 figs.

1985-09-08

224

Collective model for the odd-mass transitional nucleus "1"8"7Ir  

International Nuclear Information System (INIS)

... collective model hamiltonians iridium 187 matrix elements nuclear cores

1976-06-15

225

Radiation disinfestation of dried salted mackerel found on packaging, transporting and marketing. Part of a coordinated programme for radiation preservation of dried fish indigenous to Asia  

International Nuclear Information System (INIS)

Studies were made on different types of packaging materials used for packing dried fish in the Philippines with a view to finding a suitable packaging material for irradiated dried fish. Among these packaging materials (polyethylene, cello/polyethylene, polyester/polyethylene, Kraft paper, polypropylene and interwoven polypropylene sacks), polyester/polyethylene laminate was the most resistant material against penetration by Dermestes carnivorous. No insect damage occurred on the dried fish packed in interwoven polypropylene lined with polyester/polyethylene laminate. The cost per sack of such packaging material having a capacity of 50-80 kg is US$ 0.50. The sack lined with polyester/polyethylene proved to be durable for surface transportation from Bacolod City to Manila (approx. 360 miles). Radiation treatment at 225 krad was effective against bacterial contamination but not effective in inhibiting mould growth. Raw fish soaked in 25% salt for ...

226

Measurements of actinides in soil, sediments, water and vegetation in Northern New Mexico  

Energy Technology Data Exchange (ETDEWEB)

This study was undertaken during 1991 - 1998 to identify the origin of plutonium uranium in northern New Mexico Rio Grande and tributary stream sediments. Isotopic fingerprinting techniques help distinguish radioactivity from Los Alamos National Laboratory (LANL) and from global fallout or natural sources. The geographic area covered by the study extended from the headwaters of the Rio Grande in southern Colorado to Elephant Butte Reservoir in southern New Mexico. Over 100 samples of stream channel and reservoir bottom sediments were analyzed for the atom ratios of plutonium and uranium isotopes using thermal ionization mass spectrometry (TIMS). Comparison of these ratios against those for fallout or natural sources allowed for quantification of the Laboratory impact. Of the seven major drainages crossing LANL, movement of LANL plutonium into the Rio Grande can only be traced via Los Alamos Canyon. The majority of sampled locations within and ...

2002-01-01

227

Two dimensional analysis for equilibrium core of CANDU-PHWR  

Energy Technology Data Exchange (ETDEWEB)

The WBURN (2-D, 2-group, coarse mesh) code is developed to analyze the equilibrium core characteristics of CANDU-PHWR. The equilibrium characteristics of Wolsung reactor computed by using WBURN are compared with the values given in the Wolsung FSR. The changes of equilibrium core characteristics caused by the variation of design parameters for operating conditions are also investigated. The numerical results indicate that the average discharge irradiation in the Wolsung reactor can be increased up to about 5%.

1983-06-01

228

Two dimensional analysis for equilibrium core of CANDU-PHWR  

International Nuclear Information System (INIS)

The WBURN (2-D, 2-group, coarse mesh) code is developed to analyze the equilibrium core characteristics of CANDU-PHWR. The equilibrium characteristics of Wolsung reactor computed by using WBURN are compared with the values given in the Wolsung FSR. The changes of equilibrium core characteristics caused by the variation of design parameters for operating conditions are also investigated. The numerical results indicate that the average discharge irradiation in the Wolsung reactor can be increased up to about 5%. (Author).

1983-01-01

229

Survey of the core helium flash with dynamic convection  

Energy Technology Data Exchange (ETDEWEB)

Calculations have been performed to study the dependence on model parameters of convectively heating the region interior to the core convection zone for core helium flash models. We find that interior heating always occurs on a time scale significantly shorter than the evolutionary time scale even at the peak of the flash.

1983-06-15

230

Primary organization of nucleosomal core particles is invariable in repressed and active nuclei from animal, plant and yeast cells.  

UK PubMed Central (United Kingdom)

A refined map for the linear arrangement of histones along DNA in nucleosomal core particles has been determined by DNA-protein crosslinking. On one strand of 145-bp core DNA, histones are aligned in...Full Text Available

1985-05-24

231

Interaction between core and envelope in stars with central helium burning  

Science.gov (United States)

The interaction between core and envelope in stars with central helium burning is investigated. If core and envelope are treated as independent systems, feedback terms arise. All feedback terms are discussed in detail. The approximative treatment of feedback terms in the earlier papers of Lauterborn, Refsdal, and Weigert is found to be fully justified. The problem of secular instabilities in models with central helium burning is rediscussed. (auth)

1973-05-01

232

In-core reload design for Daya Bay Nuclear Power Station  

International Nuclear Information System (INIS)

The in-core reload design procedure, computer codes, design contents and comparison between expected design values and measured values for Daya Bay Nuclear Power Station are presented. The in-core reload design for Daya Bay Nuclear Power Station performed by Nuclear Power Institute of China satisfies the requirements of safety and economy. The expected design values are fit well with measured values

2000-12-05

233

XRF analysis of rock and sediment using standard rock samples  

Energy Technology Data Exchange (ETDEWEB)

A simple and rapid method is described for the determination of major and trace elements in rock and sediment samples by wavelength dispersive XRF. Sample measured were made from cellulose powder pressed into 4 cm diameter aluminium ring 0.4 t cm/sup -2/, and then 1 g of powdered sample (0.08 g cm/sup -2/) was placed on the disk and repressed at 1.6 t cm/sup -2/. X-ray measurements were performed for total XRF intensity (I/sub p/) at the characteristic line of each element and background intensity (I/sub b/) in vicinity of the line. The correction of matrix effect was achieved by X-ray intensity ratio of peak to background for each element. Eight standard rock samples from Geological Survey of Japan were used as standard materials, and linear calibration curves were obtained by the plot of I/sub p/ - I/sub b/ vs. concentration for Ca, Na and Pb and by the plot of I/sub p//I/sub b/ ratio vs. concentration for Si, Fe, Ti, K, P, Cl, Cr, Mn, Ni, Cu, Zn, Pb, Sr and Ba, ...

1987-03-01

234

XRF analysis of rock and sediment using standard rock samples  

International Nuclear Information System (INIS)

A simple and rapid method is described for the determination of major and trace elements in rock and sediment samples by wavelength dispersive XRF. Sample measured were made from cellulose powder pressed into 4 cm diameter aluminium ring 0.4 t cm"-"2, and then 1 g of powdered sample (0.08 g cm"-"2) was placed on the disk and repressed at 1.6 t cm"-"2. X-ray measurements were performed for total XRF intensity (I_p) at the characteristic line of each element and background intensity (I_b) in vicinity of the line. The correction of matrix effect was achieved by X-ray intensity ratio of peak to background for each element. Eight standard rock samples from Geological Survey of Japan were used as standard materials, and linear calibration curves were obtained by the plot of I_p - I_b vs. concentration for Ca, Na and Pb and by the plot of I_p/I_b ratio vs. concentration for Si, Fe, Ti, K, P, Cl, Cr, Mn, Ni, Cu, Zn, Pb, Sr and Ba, respectively. The relative standard ...

235

On the study of petroleum system operation: contribution of a two-dimensional modeling; Contribution a l`etude du fonctionnement des systemes petroliers: apport d`une modelisation bi-dimensionnelle  

Energy Technology Data Exchange (ETDEWEB)

The aim of the thesis is to validate concepts used in hydrocarbon generation and migration models; the model considered is the Temispack model developed by IFP, and the validation is based on the investigation of the thermal and hydraulic evolution in various sedimentary basins. It is shown that, in general, the thermal history of sediments is influenced by external processes (sedimentation rates, lithology, climate changes, regional-scale groundwater circulations) which frequently overprint internal processes (variations of crustal/mantle heat flow). It is found that external processes can frequently explain past thermal events that were erroneously attributed to internal causes (tectonic-thermal events). The origin of over-pressures in young basins with high sedimentation rates is shown to be generally related to compaction disequilibrium. Shale permeability values calibrated against overpressure profiles are consistent ...

1997-07-10

236

Luminescence geochronology and evaluation of the environmental dose rate for the Neanderthal deposits at Vindija Cave (Northern Croatia)  

International Nuclear Information System (INIS)

Full text: Optically stimulated luminescence (OSL) dating of individual sand-sized grains of quartz has advanced significantly over the past decade opening up new vistas in luminescence geochronology. Today, single-grain OSL dating can be used to constrain the burial ages of many deposits, including fluvial sediments, glaciofluvial material and archaeological sediments. It also provides a means of examining the stratigraphic integrity of archaeological sites where sediment mixing might have occurred. An OSL age is calculated by dividing the burial dose (the dose absorbed by the grain since it was last exposed to sunlight) by the environmental dose rate (the rate of supply of ionizing radiation to the grain over the period of burial). To obtain reliable OSL ages, therefore, an accurate estimate of the dose rate is required for each sample. Here we describe our OSL dating campaign at Vindija Cave, a key archaeological site in ...

2008-04-13

237

Interface dissolution control of the [sup 14]C profile in marine sediment  

Energy Technology Data Exchange (ETDEWEB)

The process of carbonate dissolution at the sediment-water interface has two possible end-member boundary conditions. Either the carbonate particles dissolve mostly before they are incorporated into the sediment by bioturbation (interface dissolution), or the vertical mixing is rapid relative to their extermination rate (homogeneous dissolution). In this study, a detailed radiocarbon profile was determined in deep equatorial Pacific sediment that receives a high rate of carbonate supply. In addition, a box model of sediment mixing was used to simulate radiocarbon, carbonate content, and excess thorium profiles that result from either boundary process following a dissolution increase. Results from homogeneous dissolution imply a strong, very recent erosional event, while interface dissolution suggests that moderately increased dissolution began about 10,000 years ago. In order to achieve the observed ...

1993-08-01

238

Fate of corrosion products released from stainless steel in marine sediments and seawater. Part 3. Calcareous ooze  

International Nuclear Information System (INIS)

The physicochemical forms and partitioning of corrosion products released from stainless steel upon exposure to selected environmental conditions is the subject of this investigation. This report describes the influence of calcareous sediment on the rate of release and fate of corrosion products produced when neutron-activated stainless steel specimens were exposed to a Globigerina ooze taken from the Northeast Pacific Ocean. The calcareous ooze used in this study consists largely of planktonic formanifera tests and was found to be about 90% CaCO_3. The trace metal content of this sediment was typical of average deep-sea carbonate sediments, and the ratios of trace elements to Ti were not remarkably different from a coastal clayey silt or a Northeast Pacific pelagic red clay. Most (>80%) of the trace metals extracted by sequential chemical treatment were associated with reductant-soluble materials, i.e., amorphous Mn and ...

239

Evaluating spatial patterns of dioxins in sediments to aid determination of potential implications for marine reptiles  

Energy Technology Data Exchange (ETDEWEB)

Recent investigations have identified elevated concentrations of polychlorinated dibenzo-p-dioxins (dioxins) in marine sediments and wildlife of Queensland, Australia. While it has been demonstrated that the contamination is widespread and predominantly land-based, limited information exists on the pathways and fate of these compounds within the near-shore marine system. This environment supports unique and threatened species including green sea turtles (Chelonia mydas). Adult green turtles are predominantly herbivorous, feeding on seagrass and algae. Apart from initial migration to feeding grounds (at {proportional_to}10 years of age) and intermittent migrations to breeding grounds (at {proportional_to}30-50 years and thereafter), green turtles remain and feed within relatively small home ranges. Long life-span (50 years or more), near-shore feeding grounds and highly specialized food requirements render green turtles potentially vulnerable to contaminant ...

2004-09-15

240

Acid mine drainage and its impact in the Black Creek watershed, Virginia  

International Nuclear Information System (INIS)

A one-year study was conducted to determine the impacts of acid min drainage (AMD) on the Black Creek watershed in Wise County, Virginia. Water quality, metal content of sediment and water column, soil pH, macroinvertebrate assemblages, habitat assessment and toxicity testing were used to assess the impact in the watershed. A total of 22 sites in the creek and surrounding watershed were actively monitored. This included six primary sources of AMD. Conductivity measurements > 1,000 microhmos/cm were found at eight sites and pH was consistently below 6.0 at seven. Of six metals analyzed, magnesium was highest in the water column, ranging from 16.5 mg/L to 130 mg/L. Aluminum and iron were both elevated in the sediment with iron concentrations as high as 176,000 mg/kg. An increase in sediment metal concentrations was noted when progressing downstream in the creek. Of nine high wall and spoils areas sampled, soil pH was ...

1996-11-17

241

Neutronics analysis of the 3MW TRIGA Mark-II research reactor by using SRAC code system  

British Library Electronic Table of Contents (United Kingdom)

This study deals with the neutronics analysis of the current core configuration of a 3MW TRIGA Mark-II research reactor at Atomic Energy Research Establishment (AERE), Savar, Dhaka, Bangladesh and validation of the results by benchmarking with the experimental, operational and available Safety Analysis Report (SAR) values. The comprehensive neutronics code system SRAC was used to develop a versatile and accurate full-core model of the TRIGA core. The model represents in detail all components of the core with literally no physical approximation. All fresh fuel and control elements as well as the vicinity of the core were precisely described. Cross-section data library generated from JENDL-3.2 were used. The validation of the model against benchmark experimental results is presented. The SRA...

2008-01-01

242

Flux enhancement options for an LEU-fueled MIT reactor  

International Nuclear Information System (INIS)

The Monte-Carlo transport code MCNP was used to evaluate possible arrangements of cores for the MIT Reactor using monolithic LEU fuel. Plate and moderator thicknesses were varied, and fixed absorbers and inner reflectors added in an effort to maximize available neutron fluxes at in-core and ex-core locations of experimental facilities. Addition of D_2O in the H_2O moderator was also evaluated. Comparisons of the fast, epithermal, and thermal fluxes were made at selected locations. Keff was also evaluated and critical blade heights compared with the existing HEU core. Results indicate that the LEU fluxes could approach HEU values with the use of a fueled in-core experimental facility, a fixed boron absorber spider and an inner beryllium reflector. (author)

2004-11-07

243

FFTF [Fast Flux Test Facility] management  

International Nuclear Information System (INIS)

Fuel Management at the Fast Flux Test Facility (FFTF) involves more than just the usual ex-core and in-core management of standard fuel and non-fuel components between storage locations and within the core since it is primarily an irradiation test facility. This mission involves testing an ever increasing variety of fueled and non-fueled experiments, each having unique requirements on the reactor core as well as having its own individual impact on the reload design. This paper describes the fuel management process used by the Westinghouse Hanford Company Core Engineering group that has led to the successful reload design of nine operating cycles and the irradiation of over 120 tests.

1987-09-13

244

Development of cutting technique of reactor core internals by CO laser  

International Nuclear Information System (INIS)

The CO laser is superior in the absorption characteristic to materials to the CO2 laser due to its shorter wavelength. In consideration of this characteristic Nuclear Power Engineering Corporation is studying this applicability sponsored by the Ministry of International Trade Industry of Japan to cutting of reactor core internals of commercial nuclear power plant. In decommissioning of reactor core internals it is necessary to cut stainless steel plates of 305 mm thick. The authors cut stainless steel plates of up to 310mm thick in air and those of up to 150 mm thick underwater with a 20kW class laser. Further, models simulating key structural elements of PWR core internals were cut and secondary products to clarify the applicability of the CO laser cutting to reactor core internals were evaluated. (author)

1995-04-23

245

Development and operational experience of traveling in core probe drive for flux scan of 540 MWe PHWR of Tarapur  

International Nuclear Information System (INIS)

TAPP-3 and 4 reactors use large number of Self Powered Neutron Detectors (SPNDs) for Neutronic lower measurement and control. To perform in-situ calibration of these detectors in select locations and to validate the reactor physics codes which predict flux at various points in the core, traveling in-core probes (TIP) are required. The TIP assembly consists of a miniature neutron sensitive detector. The detector is driven in and out of core using a mechanism which facilitates positioning of the detector anywhere inside a vertical tube (Central carrier tube of any of the six select Vertical Flux Units) in the core. TIP is driven through retractable feed mechanism for a stroke of 13 m. This paper describes the developmental efforts and the operational feedback of the retractable feed mechanism for the stroke of 13 m used at TAPP 3 and 4 reactor. (author)

2006-11-13

246

Comparison of the SASSYS/SAS4A radial core expansion reactivity feedback model and the empirical correlation for FFTF  

Energy Technology Data Exchange (ETDEWEB)

The present emphasis on inherent safety for LMR designs has resulted in a need to represent the various reactivity feedback mechanisms as accurately as possible. The dominant negative reactivity feedback has been found to result from radial expansion of the core for most postulated ATWS events. For this reason, a more detailed model for calculating the reactivity feedback from radial core expansion has been recently developed for use with the SASSYS/SAS4A Code System. The purpose of this summary is to present an extension to the model so that it is more suitable for handling a core restraint design as used in FFTF, and to compare the SASSYS/SAS4A results using this model to the empirical correlation presently being used to account for radial core expansion reactivity feedback to FFTF.

1987-01-01

247

The cascade of reservoirs of the ``Mayak`` Plant: Case history and the first version of a computer simulator  

Energy Technology Data Exchange (ETDEWEB)

The improvement of the ecological conditions at waste storing reservoirs is an important task of the restoration activity at Production Association (PA) ``Mayak`` (South Urals). The radionuclides mostly {sup 90}Sr, {sup 137}Cs, and chemical pollutants deposited in the reservoir water and in the bottom sediment are very dangerous sources for the contamination of Techa River below the reservoirs and the contamination of groundwater in the surrounding formations. The spreading of radioactive contaminants has both hydrogeological and the chemical features. The thermodynamic approach used to account for physical-chemical interactions between water and the bed rocks based on Gibbs free energy minimization of multicomponent system (H-O-Ca-Mg-K-Na-S-Cl-C-Sr) permitted the authors to calculate the corresponding ionic and complex species existing in the solutions, and to characterize the processes of precipitation and dissolution. The model takes into account the input and ...

1994-07-01

248

Study of metal concentration in sediment of some springs of Lebanon  

International Nuclear Information System (INIS)

Full text.Surficial sediment samples were collected from seventeen springs distributed all over Lebanon (east, west, north and south). Concentrations of metals Ca, Fe, Mn, Ni, Cu, Cr, Zn and Pb were determined by energy dispersive x-ray fluorescence technique. Irradiation was done by the radioisotope source Cd-109 and the detection by an EG and G Si(Li) detector. These analysis was done in attempt to assess the impact of anthropogenic sources on ground water quality. Metals concentration in sediment were found to be (Ca:0.05-47%, Fe:0.24-4.2%, Cr:

1999-11-02

249

National Uranium Resource Evaluation: Lander Quadrangle, Wyoming  

Energy Technology Data Exchange (ETDEWEB)

The Lander Quadrangle, Wyoming, was evaluated to a depth of 1500 m to identify environments and delineate areas that exhibit characteristics favorable for the the occurrence of uranium deposits. The evaluation used criteria established for the National Uranium Resources Evaluation program. The methods of surface investigations included evaluation of aerial radiometric and hydrogeochemical stream-sediment reconnaissance data, verification of some reported uranium occurrences, and general field geology with rock, water, and sediment sampling. The subsurface evaluation was accomplished through the use of 230 various oil-well logs. The results of this investigation identified three environments favorable for sandstone uranium deposits in Eocene fluvial sediments. These environments are within the Battle Spring and upper Fort Union Formations of the northern Great Divide Basin and within the Wind River and the Wagon Bed ...

1982-07-01

250

National Uranium Resource Evaluation: Lander Quadrangle, Wyoming  

International Nuclear Information System (INIS)

The Lander Quadrangle, Wyoming, was evaluated to a depth of 1500 m to identify environments and delineate areas that exhibit characteristics favorable for the the occurrence of uranium deposits. The evaluation used criteria established for the National Uranium Resources Evaluation program. The methods of surface investigations included evaluation of aerial radiometric and hydrogeochemical stream-sediment reconnaissance data, verification of some reported uranium occurrences, and general field geology with rock, water, and sediment sampling. The subsurface evaluation was accomplished through the use of 230 various oil-well logs. The results of this investigation identified three environments favorable for sandstone uranium deposits in Eocene fluvial sediments. These environments are within the Battle Spring and upper Fort Union Formations of the northern Great Divide Basin and within the Wind River and the Wagon Bed ...

1982-01-01

251

NOAA National Status and Trends Program Tenth Round Intercomparison for Trace Metals in Marine Sediments and Biological Tissues. National Status and Trends Program for marine environmental quality: Technical memo  

Energy Technology Data Exchange (ETDEWEB)

A total of forty participants were included in the exercise, including NOAA, USEPA, state, Australian, Canadian, Mexican and Argentinean laboratories. Two samples were sent by NRC to each participant: a contaminated marine sediment from the vicinity of New York Bay and a freeze dried mussel (Mytilus edulis) from Charlottenlund, Denmark. Laboratories were also asked to analyze two certified reference materials NIST SRM 1566a, and NRC BCSS-1. The elements to be determined were Al, Cr, Fe, Ni, Cu, Zn, As, Se, Ag, Cd, Sn, Hg, and Pb for both matrices, plus Be, Si, Mn, Sb, and Tl for the sediments. An accepted mean and confidence interval were calculated for each analyte in the two unknown samples. Laboratory biases were identified and an overall rating of superior, good, fair or others was assigned to each laboratory.

1996-11-01

252

Consequences of power peak production on sediments in tunnels and surge shafts. Partial report Phase 1: Field investigations; Konsekvenser av effektkjoering paa sedimentforhold i tunneler og svingesjakter. Delrapport fase 1: Feltundersoekelser  

Energy Technology Data Exchange (ETDEWEB)

In July 1997, a field inspection was carried out of parts of the tunnel system of the Tonstad hydroelectric power station, Norway. This report discusses the findings: (1) The main drift has a varying bottom covering of sediments, (2) The tunnel to Ousdal had on its downmost 2 km an almost unbroken and apparently stable armour layer along the walls and an unstable or incomplete armour layer in the middle, (3) The tunnel to Homstoel almost had no bottom layer, (3) Sediments in side inlets and niches are of two kinds: (a) masses added through side inlets, (b) fine sand and mud deposited by the main tunnel, (4) A few cases were observed of downfallen rocks and of peeled rock of about 1 m size. It looks as if the Homstoel tunnel may have been previously used for larger discharges than that from Ousdal and that the latter is now being used to the limit of what the previously established armour layer can stand

1997-10-01

253

Adaptive response of the chicken embryo to low doses of x-irradiation  

Energy Technology Data Exchange (ETDEWEB)

Chicken embryos were x-irradiated in ovo with 5-30 cGy (=priming dose) at the 13th-15th day of development. After 3-48 h, brain- and liver-cell suspensions were x-irradiated in vitro with (challenge) doses of 4-32 Gy. Significantly less radiation damage was observed when the radiation response was measured by scheduled DNA synthesis, nucleoid sedimentation and viscosity of alkaline cell lysates 12-36 h after the priming exposure. In vivo, pre-irradiation with 10 cGy enhanced regeneration as evidenced by the DNA content of chicken embryo brain and liver 24 h following a challenge dose of 4 Gy. From nucleoid sedimentation analyses in brain and liver cells immediately after irradiation with 16 Gy and after a 30-min repair period in the presence of aphidicolin, dideoxythymidine and 3-aminobenzamide or in the absence of these DNA repair inhibitors, it is concluded that a reduction of the initial radiation damage is the dominant mechanism of the ...

1995-08-01

254

Enhancement of the sweep efficiency of waterflooding operations by the in-situ microbial population of petroleum reservoirs  

Energy Technology Data Exchange (ETDEWEB)

Live cores were obtained from five reservoirs using special precautions to prevent contamination by exogenous microorganisms and minimize exposure to oxygen. The depths from which the cores were obtained ranged from 2,705 ft to 6,568 ft. Core plugs were cut radially from live cores, encased in heat-shrink plastic tubes, placed in core holders, and fitted with inlets and outlets. Nutrient additions stimulated the in-situ microbial population to increase, dissolve stratal material, produce gases, and release oil. Reduction in flow through the core plugs was observed in some cases, while in other cases flow was increased, probably due to the dissolution of carbonates in the formation. A field demonstration of the ability of the in-situ microbial population to increase oil recovery by blocking the more permeable zones of the reservoir is currently underway. This ...

1995-12-31

255

Core Heat Transfer Model Validation of the TASS/SMR-S Code using the Bennett's Test  

International Nuclear Information System (INIS)

The SMART (System-integrated Modular Advanced ReacTor) which is a 330 MWt advanced integral PWR was developed by the KAERI (Korea Atomic Energy Institute) for electricity generation and seawater desalination. A thermal hydraulic evaluation and analysis of the SMART is performed by the TASS /SMR-S (Transient And Setpoint Simulation/System integrated Modular Reactor-Safety). The TASS/SMR-S code has various models reflecting the design features of the SMART such as the drift flux model, the core models (core power and core heat transfer model), the component models, and the specific models. One of the core models is the core heat transfer model. The role of this model is to calculate the heat flux and radial temperature profiles at a fuel rod surface using the relevant heat transfer correlations for all of the heat transfer modes. Also it is modeled to meet the requirements of the 10 ...

2010-10-01

256

Analysis of High-Moderation MOX Core MISTRAL-3 with SRAC and MVP  

International Nuclear Information System (INIS)

To obtain reactor physics parameters for high-moderation mixed-oxide (MOX) cores, Nuclear Power Engineering Corporation (NPEC), the French Atomic Commission (CEA), and their industrial partners have conducted a MOX core physics experimental program called MISTRAL with the EOLE critical facility of the Cadarache research center. This program consists of four high-moderation cores and was successfully completed in July 2000. This paper describes the analysis results of MISTRAL-3 that is a homogeneous full MOX cylindrical core (H/HM = 6.2) with an 80-cm height and a 59-cm diameter consisting of 1388 standard pressurized water reactor-type MOX fuel rods of 7.0 wt% plutonium-enrichment in a square pitch of 1.39 cm. NPEC has been analyzing the experimental results by using the SRAC and MVP code systems. SRAC and MVP calculate the nuclear core characteristics correctly for the ...

2001-06-17

257

Oxidation and adsorption of Co(II)EDTA 2- complexes in subsurface materials with iron and manganese oxide grain coatings  

Science.gov (United States)

Batch interaction experiments were performed under aerobic conditions to characterize the adsorption behavior and valence speciation of CoEDTA complexes (equimolar at 10 -5 mol/L) in a series of Pliocene subsurface sediments containing various amounts of Fe and Mn oxides. The experiments were performed in 0.003 mol/L Ca(ClO 4 ) 2 with a solids concentration of 500 g/L at variable pH (4-9) and at the natural pH of the sediments (pH = 8.3). Three of these subaerial sediments (Ringold 1, 2, 3) contained significant quantities of extractable Fe and Mn, while the fourth (Ringold 4) was virtually devoid of sesquioxide precipitates. Microscopic and mineralogic analyses of the most heavily encrusted material (Ringold 2) showed that the oxides existed as intergrain cements and contained crystalline goethite and rancieite/todorokite. Adsorption on a synthetic analog sorbent (0.6 mass % ferrihydrite-coated sand) over a range in pH ...

1995-11-01

258

Optical dating: insufficiently bleached sediments  

International Nuclear Information System (INIS)

Although infrared-stimulated luminescence (IRSL) signals in feldspars can be bleached rapidly by sunlight, there could still be a small amount of IRSL signal remaining in sediment grains if they have experienced only relatively short sunlight exposure before deposition. This remaining signal results in a ''remnant dose'' stored in the grain and is important for young samples but negligible for old samples. Several methods have been introduced to detect insufficient bleaching, and some of them can provide information on the extent of the bleaching. Others can only distinguish between samples bleached for a very long time and for a short time. Empirical methods are introduced to evaluate the possible values of equivalent dose accumulated since the grains were deposited. These methods involve the analysis of the equivalent doses and the natural IRSL signals obtained using single-disc dose determination methods. (author).

1993-07-01

259

On the quantitative distribution and community structure of the meio and macrofaunal communities in the coastal area of the Central Adriatic Sea (Italy)  

British Library Electronic Table of Contents (United Kingdom)

Many coastal areas have served as repositories of different anthropogenic and naturally induced organic material and nutrients. The major sources thereof are riverine inputs which strongly influence the spatial and temporal distribution of benthic communities. In this study, the benthic foraminiferal, meiofaunal, and macrofaunal colonies in front of three rivers in a poorly known, but environmentally valuable, area of the Central Adriatic Sea have been examined concurrently. The physico-chemical parameters of bottom water and sediment characteristics were determined in order to characterize both the sediment?water interface and the benthic environments. Although changes in the biota are neither univocal nor unidirectional, a moderate influence of riverine input on the different communities...

2011-01-01

260

New stratigraphic markers in the late Pleistocene Palouse loess: novel fossil gastropods, absolute age constraints and non-aeolian facies  

British Library Electronic Table of Contents (United Kingdom)

Abstract Four stratigraphic sections in the southern part of the Columbia Basin preserve a sequence of aeolian and non-aeolian sediments ranging in age from 943 to >470 14C ka based on accelerator mass spectrometry radiocarbon dating of fossil molluscs, geochemistry of Cascade Mountain-sourced tephra and association with formally recognized pedostratigraphic units (the Washtucna and Old Maid Coulee soils). Study sections are interpreted as representing concurrent deposition of loess and distal Missoula Flood rhythmites in valleys tributary to main drainages backflooded during the Missoula Floods, and formation of carbonate and iron-rich soils. Sediments belong to the formally recognized L-1 and L-2 loess units established for the Palouse loess, which were deposited in the Columbia Basin su...

2010-01-01

261

Development of a waterjet system for direct delivery of granular iron and activated carbon to remediate contaminated aqueous sediments  

British Library Electronic Table of Contents (United Kingdom)

Abstract While the techniques and technologies associated with contaminated sediment remediation are relatively mature, there are several issues associated with these practices that make them unattractive. The inability of currently used mechanical mixing implements to place amendments in aqueous environments and their intrusive behavior toward benthic communities are just two examples of a necessity for an improved delivery method. Waterjets may be a viable option for placement of particulate remediation amendments, such as activated carbon and granular iron, at depth. A custom waterjet nozzle and injection system has been fabricated by the authors to examine this delivery concept. The developed injection system's performance was tested by characterizing the waterjet-delivered amendment (...

2011-01-01

262

Biodynamic modelling of the accumulation of Ag, Cd and Zn by the deposit-feeding polychaete Nereis diversicolor: Inter-population variability and a generalised predictive model  

British Library Electronic Table of Contents (United Kingdom)

Biodynamic parameters of the ragworm Nereis diversicolor from southern Spain and south England were experimentally derived to assess the inter-population variability of physiological parameters of the bioaccumulation of Ag, Cd and Zn from water and sediment. Although there were some limited variations, these were not consistent with the local metal bioavailability nor with temperature changes. Incorporating the biodynamic parameters into a defined biodynamic model, confirmed that sediment is the predominant source of Cd and Zn accumulated by the worms, accounting in each case for 99% of the overall accumulated metals, whereas the contribution of dissolved Ag to the total accumulated by the worm increased from about 27 to about 53% with increasing dissolved Ag concentration. Standardised va...

2010-01-01

263

Oak Ridge National Laboratory Core Competencies  

Energy Technology Data Exchange (ETDEWEB)

A core competency is a distinguishing integration of capabilities which enables an organization to deliver mission results. Core competencies represent the collective learning of an organization and provide the capacity to perform present and future missions. Core competencies are distinguishing characteristics which offer comparative advantage and are difficult to reproduce. They exhibit customer focus, mission relevance, and vertical integration from research through applications. They are demonstrable by metrics such as level of investment, uniqueness of facilities and expertise, and national impact. The Oak Ridge National Laboratory (ORNL) has identified four core competencies which satisfy the above criteria. Each core competency represents an annual investment of at least $100M and is characterized by an integration of Laboratory technical foundations in physical, chemical, ...

1994-12-01

264

Tribo-characteristics of self-lubricating ball bearings for the LE-7 liquid hydrogen rocket-turbopump  

Energy Technology Data Exchange (ETDEWEB)

The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of PTFE transfer film with bearing seizure ...

1993-07-01

265

The effect of irradiation on packaging materials  

International Nuclear Information System (INIS)

Ionizing radiation, mainly in the form of #gamma#-rays from the radioisotope cobalt 60, is being used increasingly for the inactivation of contaminants in cosmetic and toiletry preparations. The treatment is applied to the product in its final pack, and therefore, it is important to recognize that the properties of the packaging materials could be affected, particularly if high radiation doses are used. The stability of a wide range of materials is discussed. The nature and extent of chemical and physical changes in plastics very much depends on the presence of antioxidants and other additives, and on the environmental conditions during irradiation. Some useful information is available from research into the use of radiation for the preservation of food - many films and laminates have been cleared for use in the United States. The low radiation doses used for the control of contaminants in cosmetic products are quite unlikely to cause changes in packaging materials ...

266

Self-lubricating performance and durability of ball bearings for the LE-7 liquid oxygen rocket-turbopump  

Energy Technology Data Exchange (ETDEWEB)

The durability of ball bearings, 32-mm- and 45-mm-bore, with a retainer or glass cloth-polytetrafluoroethylene (PTFE) laminate was tested under a high radial load at a speed of 20,000 rpm in LOX or LN2. The retainers were characterized as good self-lubricators because the abrasive glass-cloth fiber tips exposed on the retainer were chemicaly etched away with hydrofluoric acid (HF). During testing, the bearing-cartridge-acceleration was monitored to detect bearing damage. Testing in LOX for about 2.2 hr showed that excellent lubricating conditions were obtained for all bearings. Testing in LN2 for about 5.1 hr detected that the fatigue life of the bearing was about the same as the calculated B10 fatigue life. The HF chemical treatment resulted in a reacted fluoride-oxide material which remained in the etched part of the glass fiber. Several chemical products, particularly MgO, CaO, and CaCO3, enhanced adhesion of PTFE transfer film to the counterface, resulting in ...

1993-09-01

267

R and D for a single-layer Nb{sub 3}Sn common coil dipole using the react-and-wind fabrication technique  

Energy Technology Data Exchange (ETDEWEB)

A dipole magnet based on the common coil design, using prereacted Nb{sub 3}Sn superconductor, is under development at Fermilab, for a future Very Large Hadron Collider. This magnet has some innovative design and technological features such as single layer coils, a 22 mm wide 60-strand Rutherford type cable and stainless steel collars reinforced by horizontal bridges inserted between coil blocks. Both left and right coils are wound simultaneously into the collar structure and then impregnated with epoxy. In order to optimize the design and fabrication techniques an R&D program is underway. The production of cables with the required characteristics was shown possible. Collar laminations were produced, assembled and tested in order to check the effectiveness of the bridges and the validity of the mechanical design. A mechanical model consisting of a 165 mm long section of the magnet straight section was assembled and tested. This paper summarizes the status of ...

2002-01-14

268

On the bending response of Kevlar 49/epoxy beams and rings  

Energy Technology Data Exchange (ETDEWEB)

Kevlar 49/epoxy laminates often exhibit substantial material nonlinearity when subjected to bending. This is a consequence of the yeild-like behavior of a Kevlar 49/epoxy lamina in fiber-directed compression. In this paper, analyses that utilize a simple idealization of compressive yielding are described and calculated results for Kevlar 49 reinforced beams and rings are compared with available data. First, results of a finite element analysis of a thin, unidirectionally reinforced ring subjected to diametral compression are presented. This analysis uses beam elements that incorporate linear tensile and elastic-perfectly plastic compressive behavior. Then a method used to analyze quasi-isotropic beams tested in four-point bending is discussed. This finite element analysis uses a layered shell element with a lamina constitutive model that permits elastic-perfectly plastic response to fiber-directed compression, but otherwise assumes linear elastic behavior. ...

1988-05-01

269

Method for forming a bladder for fluid storage vessels  

Energy Technology Data Exchange (ETDEWEB)

A lightweight, low permeability liner for graphite epoxy composite compressed gas storage vessels. The liner is composed of polymers that may or may not be coated with a thin layer of a low permeability material, such as silver, gold, or aluminum, deposited on a thin polymeric layer or substrate which is formed into a closed bladder using torispherical or near torispherical end caps, with or without bosses therein, about which a high strength to weight material, such as graphite epoxy composite shell, is formed to withstand the storage pressure forces. The polymeric substrate may be laminated on one or both sides with additional layers of polymeric film. The liner may be formed to a desired configuration using a dissolvable mandrel or by inflation techniques and the edges of the film seamed by heat sealing. The liner may be utilized in most any type of gas storage system, and is particularly applicable for hydrogen, gas mixtures, and oxygen used for vehicles, fuel ...

2000-01-01

270

Lightweight bladder lined pressure vessels  

Energy Technology Data Exchange (ETDEWEB)

A lightweight, low permeability liner for graphite epoxy composite compressed gas storage vessels. The liner is composed of polymers that may or may not be coated with a thin layer of a low permeability material, such as silver, gold, or aluminum, deposited on a thin polymeric layer or substrate which is formed into a closed bladder using torispherical or near torispherical end caps, with or without bosses therein, about which a high strength to weight material, such as graphite epoxy composite shell, is formed to withstand the storage pressure forces. The polymeric substrate may be laminated on one or both sides with additional layers of polymeric film. The liner may be formed to a desired configuration using a dissolvable mandrel or by inflation techniques and the edges of the film seamed by heat sealing. The liner may be utilized in most any type of gas storage system, and is particularly applicable for hydrogen, gas mixtures, and oxygen used for vehicles, fuel ...

1998-01-01

271

Full scale testing of wind turbine blade to failure - flapwise loading  

Energy Technology Data Exchange (ETDEWEB)

A 25m wind turbine blade was tested to failure when subjected to a flapwise load. With the test setup, it was possible to test the blade to failure at three diffe-rent locations. The objective of these tests is to learn about how a wind turbine blade fails when exposed to a large flapwise load and how failures propagate. The report shows also results from ultra sonic scan of the surface of the blade and it is seen to be very useful for the detection of defects, especially in the layer between the skin laminate and the load carrying main spar. Acoustic emission was successfully used as sensor for the detection of damages in the blade during the test. The report contains measurements of the total deflection of the blade, the local deflection of the skin and the load carrying main spar and also measurement of strain all as a function of the applied load and up to failure of the blade. The 'post mortem' analysis and description of how the damages ...

2004-06-01

272

Effects of atmospheric pressure on tracking failure of organic insulating materials; Yuki zetsuen zairyo no tai tracking sei ni oyobosu kiatsu no eikyo  

Energy Technology Data Exchange (ETDEWEB)

The effect of atmospheric pressure on tracking resistance of organic insulating materials were investigated in the range of 500 to 1007 hPa. The tracking resistance for Polycarbonate (PC), Modified Polyphenylene Oxide (M-PPO) and Paper Base Phenolic Resin Laminate (PL) increase with the decrease in atmospheric pressure. The scintillating discharges on these samples surface lead to the ignition. The tracking failure on these results from the ignition on the surface. For Polybutylene Terephthalate (PBT) and Polyethylene Terephthalate (PET), the tracking resistance decrease with the decrease in atmospheric pressure. The discharges observed on the these surface are the glow-like. The discharge area spreads on the surface between the electrodes at the lower pressure. The failure on this group results from the carbonization by the discharges on the surface. However, the tracking resistance for Unsaturated Polyester Resins (UP) has no significant dependence on lower ...

1995-11-20

273

Chip type aluminum solid electronic capacitor using polypyrrole. Polypyrrole wo mochiita chip gata aluminum kotai denkai condenser  

Energy Technology Data Exchange (ETDEWEB)

In the past, organic substance is generally deemed as electrical insulator, but in recent years, molecular crystals and polymers showing electroconductivity like metal were synthesized and even those showing superconductivity have appeared. These materials are called organic metals or synthetic metals and have peculiar solid state physical properties. Examples of real application of organic electroconductive materials are becoming available, but in this article, a chip type aluminum solid electrolytic capacitor using polypyrrole is introduced. There are four kinds of capacitors including ceramic capacitors and aluminum electrolytic capacitors, etc. The aluminum electrolytic capacitor is most retarded than any other type of capacitor in introducing its chip type since its use of electrolytic solution becomes an obstacle. Polypyrrole synthesized by electrolytic polymerization through anode oxidation of pyrrole has good stability and high electroconductivity. Introduction of the chip type ...

1990-07-05

274

Applications or radiation polymerization hardening to composites  

International Nuclear Information System (INIS)

Comprehensive investigation has been made into the application of the polymerization hardening by radiation, particularly electron beam, to the composites of polymers and other materials. The report is divided into four parts, namely 1) characteristics and problems of the reaction of curing by radiation polymerization, 2) improvement of the bonding capability of high molecular weight materials, 3) bonding by radiation, and 4) composites made by the impregnation and polymerization hardening of monomers. The first part includes the effects of dose rate, temperature rise during the hardening, the peculiarity of electron beam irradiation at high dose rate, reaction environment and additive effects. Main conclusions are as follows: caution must be taken to the amount of residual double bonds because they affect the quality of hardened polymers; the polymerization hardening reaction at high dose rate cannot be analogized by that at low dose rate; and the presence of the inhibitors of radical ...

1976-01-01

275

Application of multi-stage, multi-disk type downhole seismic source; Tadanshiki taso enbangata koseinai shingen no tekiyosei  

Energy Technology Data Exchange (ETDEWEB)

A multi-stage, multi-disk type seismic source was developed as a downhole seismic source. The seismic source is an improved version of the downhole seismic source of a system in which an elastic wave is generated by a weight accelerated by restitutive force of a spring striking the upper part of a laminated structure consisted of metal disks and elastic bodies installed in water in a well. Enhancing the vibration exciting efficiency requires impedance radiated from the disks to be increased. The multi-disk structure was adopted because of restrictions on the disk area under the limiting condition of being inside the well. Further limitation has still existed, which led to finally structuring the multi-disk type to a multi-stage construction to increase the radiated impedance. In order to increase average velocity on the radiation surface, mass relationship between the hammer and the anvil was sought so that the maximum velocity is achieved at the process of ...

1997-05-27

276

Thermographic studies of the interaction between hydrolyzed polyacrylonitrile and Ca/sup 2 +/, Fe/sup 3 +/, Cu/sup 2 +/ ions  

Energy Technology Data Exchange (ETDEWEB)

Reasons were revealed for the fresh water resistance of sediments of hydrolyzed polyacrylonitrile obtained from interaction of it with Fe/sup 3 +/, Ca/sup 2 +/ and Cu/sup 2 +/ cations which are in the saline solutions of these metals.

1982-01-01

277

Stratigraphic drilling report - GSQ Ipswich 26  

Energy Technology Data Exchange (ETDEWEB)

The stratigraphic bore GSQ Ipswich 26 was drilled by the Department of Mines southeast of Ipswich in 1981. Late Triassic sedimentary rocks of the Moreton and Ipswich Basins were encountered above 919.9 m depth. Below this depth acid to intermediate volcanic rocks and minor amounts of interbedded volcanogenic sediments were intersected, also probably of Late Trassic age. The bore reached a total depth of 1238.8 m in volcanogenic conglomerates and sandstones.

1982-11-01

278

Seismic stratigraphy based chronostratigraphy (SSBC) of the Serbian Banat region of the Pannonian Basin  

Science.gov (United States)

Seismic stratigraphy based chronostratigraphic (SSBC) analysis of the Serbian Banat region allows the delineation of the spatial and stratigraphic relationships of the generally regressive and shallowing upward Neogene depositional fill of a tectonically unstable central portion of the Pannonian Basin. When geometrically restored in time and space, the sediment dispersal directions, sediment source directions, types of sedimentation breaks and the tectonic events influencing basin evolution can be delineated. For such an analysis the time-transgressive lithostratigraphic units used in the neighbouring Hungarian part of the Pannonian Basin are conveniently introduced based upon their characteristic seismic facies and constrained borehole log records as mappable seismic stratigraphic sequence units, termed "seismic operational sequences". The respective Neogene stage and operational sequence equivalents (Hungarian ...

2010-12-01

279

Seismic stratigraphy and salt tectonics of upper Continental Slope, East Breaks flexure trend, Gulf of Mexico  

Science.gov (United States)

A study of more than 1200 of 72-fold, migrated, seismic reflection profiles, from the eastern part of the East Breaks flexure trend, Gulf of Mexico, indicates that, although individual seismic reflectors cannot be traced across the entire area, seismic depositional units can be recognized and correlated from basin to basin in most instances. Three tentative conclusions are evident from this study: (1) salt diapirs appear to have grown through a series of intermittent movements to form structurally separate intraslope basins; (2) sedimentation is probably channeled by differential dome growth, which creates local stratigraphic differences between basins; and (3) packages of distinctive seismic depositional units can be successfully used to map sediment cycles between separate basins. Fluctuations of Pleistocene sea level appears to be the dominate depositional control on the upper continental slope in this area. During high sea level stands, ...

1986-05-01

280

Quantitation of transcribing native simian virus 40 minichromosomes extracted from CV1 cells late in infection.  

UK PubMed Central (United Kingdom)

Simian virus 40 transcriptional complexes could be extracted from CV1 cells late in infection and separated from the bulk of inactive viral chromatin. Sucrose gradient sedimentation, cesium sulfate...Full Text Available

1981-04-01

281

Population dynamics of dechlorinators and factors affecting the level and products of PCB dechlorination in sediments  

Energy Technology Data Exchange (ETDEWEB)

Microbial dechlorination of polychlorinated biphenyls (PCBs) often stops although a significant number of removable chlorines remain. To determine the reason for the cessation, we investigated the limitation of organic carbon, PCB bioavailability, and inhibition by metabolic products. Enrichment with carbon sources did not induce additional chlorination, indicating the plateau was not due to depletion of organic carbon. The bioavailability was not limiting, since a subcritical micelle concentration of the surfactant, which enhanced desorption without inhibiting dechlorinating microorganisms, failed to lower the plateau. Neither was it due to accumulation of metabolites, since no additional dechlorination was detected when plateau sediments were incubated with fresh medium. Similarly, dechlorination was not inhibited in freshly spiked sediment slurries. Dechlorination ended up at the same level with nearly identical congener profiles, regardless ...

1996-12-31

282

Performance assessment overview for subseabed disposal of high level radioactive waste  

Energy Technology Data Exchange (ETDEWEB)

The Subseabed Disposal Project (SDP) was part of an international program that investigated the feasibility of high-level radioactive waste disposal in the deep ocean sediments. This report briefly describes the seven-step iterative performance assessment procedures used in this study and presents representative results of the last iteration. The results of the performance are compared to interim standards developed for the SDP, to other conceptual repositories, and to related metrics. The attributes, limitations, uncertainties, and remaining tasks in the SDP feasibility phase are discussed.

1997-06-01

283

Mercury Removal, Methylmercury Formation, and Sulfate-Reducing Bacteria Profiles in Wetland Mesocosms Containing Gypsum-Amended Sediments and Scirpus californicus  

Energy Technology Data Exchange (ETDEWEB)

A pilot-scale model was constructed to determine if a wetland treatment system (WTS) could effectively remove low-level mercury from an outfall located at the Department of Energy's Savannah River Site.

2001-03-02

284

Investigations into Wetland Carbon Sequestration as Remediation for Global Warming  

Energy Technology Data Exchange (ETDEWEB)

Wetlands can potentially sequester vast amounts of carbon. However, over 50% of wetlands globally have been degraded or lost. Restoration of wetland systems may therefore result in increased sequestration of carbon. Preliminary results of our investigations into atmospheric carbon sequestration by restored coastal wetlands indicate that carbon can be sequestered in substantial quantities in the first 2-50 years after restoration of natural hydrology and sediment accretion processes.

2002-01-01

285

Infrared-stimulated luminescence dating of sediments  

Energy Technology Data Exchange (ETDEWEB)

Luminescence stimulated from feldspars using wavelengths in the infrared region can be applied to the dating of sedimentary grains. Reported stimulation spectra are very similar for a wide range of feldspars, but their emission spectra show greater variation. For accurate dating it is critical that unstable infrared-stimulated luminescence (IRSL) signals are removed from the laboratory-irradiated grains. Several approaches to isolate a thermally stable signal are described. (author).

1994-04-01

286

Detection of polychlorinated biphenyl degradation genes in polluted sediments by direct DNA extraction and polymerase chain reaction  

Energy Technology Data Exchange (ETDEWEB)

It was the aim of this study to specifically detect the DNA sequences for the bphC gene, the meta-cleavage enzyme of the aerobic catabolic pathway for biphenyl and polychlorinated biphenyl degradation, in aquatic sediments without prior cultivation of microorganisms by using extraction of total DNA, PCR amplification of bphC sequences, and detection with specific gene probes. The direct DNA extraction protocol used was modified to enhance lysis efficiency. Crude extracts of DNA were further purified by gel filtration, which yielded DNA that could be used for the PCR. PCR primers were designed for conserved regions of the bphC gene from a sequence alignment of five known sequences. The specificity of PCR amplification was verified by using digoxigenin-labeled DNA probes which were located internal to the amplified gene sequence. The detection limit for the bphC gene of Pseudomonas paucimobilis Q1 and Pseudomaonas sp. strain LB 400-like sequences for the bphC gene ...

1993-12-01

287

Density Currents  

Science.gov (United States)

In this activity, students will make a turbidity current. They will discover how fluids of differing densities interact with one another, learn some ways the densities of fluids can be changed and observe how density currents transport and deposit tremendous amounts of sediment in lakes and in the ocean. Additional options allow students to create and observe different kinds of density currents.

288

Albian clastics in the western Arabian Gulf region: a sedimentological and petroleum-geological interpretation  

Energy Technology Data Exchange (ETDEWEB)

Clastic sediments of Albian age provide hydrocarbon source rocks, reservoirs and seals. Major reservoirs occur in sandstones to the north, and have a limited reservoir potential in offshore Qatar. Distal shales are a major seal in offshore Qatar, the United Arab Emirates and Oman. Local source-rock potential exists in the northern part of the Arabian Gulf and in the extreme SE of Saudi Arabia (in the Rub Al Khali Basin). (author)

1994-07-01

289

Airborne hyperspectral data for the assessment of open cast lignite mining impacts in central Germany  

Energy Technology Data Exchange (ETDEWEB)

The application of airborne sensors for providing environmental assessment and monitoring of a test site in an open cast mining area that is part of a lignite deposit in central Germany is described. Hyperspectral remote sensing data from three different sensors were tested. The hyperspectral scanner data was suitable for classification of different sediments and vegetation types and the water chemistry of residual mining lakes. Summary form only. 1 tab.

1999-07-01

290

7. Overview of radionuclide X-ray fluorescence analysis of components of the environment  

International Nuclear Information System (INIS)

A survey is presented of studies dealing with radionuclide X-ray fluorescence analysis (RXFA) of impurities in the air, water, soil, sediments and biological materials, mainly blood, urine, hair, soft tissues and bones. Tabulated are lists of published works on RXFA of the air, water and biological materials. (ES).

1983-12-01

291

Stress corrosion cracking of austenitic stainless steel core internal welds.  

Energy Technology Data Exchange (ETDEWEB)

Microstructural analyses by several advanced metallographic techniques were conducted on austenitic stainless steel mockup and core shroud welds that had cracked in boiling water reactors. Contrary to previous beliefs, heat-affected zones of the cracked Type 304L, as well as 304 SS core shroud welds and mockup shielded-metal-arc welds, were free of grain-boundary carbides, which shows that core shroud failure cannot be explained by classical intergranular stress corrosion cracking. Neither martensite nor delta-ferrite films were present on the grain boundaries. However, as a result of exposure to welding fumes, the heat-affected zones of the core shroud welds were significantly contaminated by oxygen and fluorine, which migrate to grain boundaries. Significant oxygen contamination seems to promote fluorine contamination and suppress thermal sensitization. Results of slow-strain-rate tensile tests also ...

1999-04-14

292

Preliminary studies of coolant by-pass flows in a prismatic very high temperature reactor using computational fluid dynamics  

Energy Technology Data Exchange (ETDEWEB)

Three dimensional computational fluid dynamic (CFD) calculations of a typical prismatic very high temperature gas-cooled reactor (VHTR) were conducted to investigate the influence of gap geometry on flow and temperature distributions in the reactor core using commercial CFD code FLUENT. Parametric calculations changing the gap width in a whole core length model of fuel and reflector columns were performed. The simulations show the effects of core by-pass flows in the heated core region by comparing results for several gap widths including zero gap width. The calculation results underline the importance of considering inter-column gap width for the evaluation of maximum fuel temperatures and temperature gradients in fuel blocks. In addition, it is shown that temperatures of core outlet flow from gaps and channels are strongly affected by the gap width of by-pass flow in the reactor ...

2009-09-01

293

Oil-filled, multi-core cable with at least one conductor differing from others  

Energy Technology Data Exchange (ETDEWEB)

This patent discloses an oil-filled, multi-core, electric cable having three cores within a metal sheath suitable for underwater applications. Each core has a conductor surrounded by insulation and has substantially the same outer dimensions as the other cores. One conductor is made of copper and has a central oil duct. The other conductors are made of stranded aluminum wires in side-by-side and contacting relation and the ratio of the cross-sectional area of the metal of the copper conductor to the cross-sectional area of the metal of each aluminum conductor is the reciprocal of the ratio of the electrical conductivities thereof. One object of this invention is that of overcoming the drawbacks existing in the known oil-filled, multi-core cables, i.e. to provide cable which, in case of a rupture of the cable sheath, has fairly small leakages of insulating, fluid oil from the cable ...

1987-02-03

294

Fast Flux Test Facility reactor initial criticality predictions and measurements  

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) was designed to test fast-reactor fuels and other nonfuel materials. In its 37 reactor cycles of operations, the FFTF reactor has performed very well and successfully completed all the irradiation testings with an operating efficiency factor as high as 98%. Since FFTF is an experimental reactor, its core loading changed from cycle to cycle. Depending on the number of test assemblies in the core and their location, the core loading can change significantly from an essentially homogeneous core loading to a relatively nonhomogeneous or even highly localized heterogeneous loading. Consequently, the core reload design and initial criticality analyses were required for each operating cycle. The zero power initial critical control rod bank height was predicted before each reactor startup. The initial critical prediction depends on the reactivity ...

1992-06-07

295

FFTF [Fast Flux Test Facility] fuel handling experience (1979--1986)  

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF)is a 400 MW (th) sodium-cooled fast flux test reactor located on the Hanford Site in southeastern Washington State. The FFTF is operated by the Westinghouse Hanford Company for the United States Department of Energy. The FFTF is a three loop plant designed primarily for the purpose of testing full-scale core components in an environment prototypic of future liquid metal reactors. The plant design emphasizes features to enhance this test capability, especially in the area of the core, reactor vessel, and refueling system. Eight special test positions are provided in the vessel head to permit contact instrumented experiments to be installed and irradiated. These test positions effectively divide the core into three sectors. Each sector requires its own In-Vessel Handling Machine (IVHM) to access all the core positions. Since the core and the in-vessel ...

1987-09-01

296

Data report of BWR post-CHF tests. Transient core thermal-hydraulic test program. Contract research  

Energy Technology Data Exchange (ETDEWEB)

JAERI has been performing transient core thermal-hydraulic test program. In the program, authors performed BWR/ABWR DBE simulation tests with a test facility, which can simulate BWR/ABWR transients. The test facility has a 4 x 4 bundle core simulator with 15-rod heaters and one non-heated rod. Through the tests, authors quantified the thermal safety margin for core cooling. In order to quantify the thermal safety margin, authors collected experimental data on post-CHF. The data are essential for the evaluation of clad temperature transient when core heat-up occurs during DBEs. In comparison with previous post-CHF tests, present experiments were performed in much wider experimental condition, covering high clad temperature, low to high pressure and low to high mass flux. Further, data at wider elevation (lower to higher elevation of core) were obtained in the present experiments, ...

2001-03-01

297

CT-guided percutaneous core biopsies of pulmonary lesions: Diagnostic accuracy, complications and therapeutic impact  

International Nuclear Information System (INIS)

To evaluate the diagnostic accuracy, complications, and therapeutic impact of CT-guided percutaneous core biopsies of pulmonary lesions. Material and methods: Seventy-nine patients underwent diagnostic CT-guided percutaneous core biopsies of pulmonary lesions between July 1995 and March 1999. Evaluation included corresponding clinical data, pathologic results, and therapeutic consequences. Results: There were 29 benign and 50 malignant lesions. Percutaneous core biopsy had an overall diagnostic accuracy of 95%. For malignant lesions, core biopsy was positive in 48 patients (sensitivity 96%), and for benign lesions, in 27 (sensitivity 93%). There were no false-positive findings. Pneumothoraces were observed in 19 patients (24%) and 4 of them required a chest drain (5%). There were no hematothoraces or major bleeding complications; however, postinterventional local hemorrhages were observed in 23 patients ...

2001-03-01

298

Steady-state neutronic investigations to the accident of water ingress in systems with pebble-bed high-temperature gas-cooled reactor fuel  

Energy Technology Data Exchange (ETDEWEB)

For light water reactors, loss of coolant is an important point in safety analysis, whereas for gas-cooled reactors the ingress of water into the core region is an incident of safety relevance. The applicability of the computer code system GAMTEREX to pebble beds of spherical high-temperature gas-cooled reactor fuel elements with simulated water ingress is verified by experiment. The measurements were performed at a Siemens-Argonaut reactor, using its ring core as a driver zone for a pebble-bed core in the center of the reactor.

1987-09-01

299

Method to generate the first design of the reload pattern to be used with the Presto-B code in the simulation of the CNLV U-1 reactor; Metodo para generar el primer diseno del patron de recarga a ser utilizado con el codigo Presto-B, en la simulacion del reactor de la CNLV U-1  

Energy Technology Data Exchange (ETDEWEB)

This guide is applied for the reload pattern's formation for mirror symmetry of a core room and in accordance with the Control Cell core technique (of the english Control Cell Core - CCC) for the PRESTO-B code. (Author)

1992-08-15

300

Large scale usage of depleted uranium bundles in Indian PHWRS  

International Nuclear Information System (INIS)

Indian PHWRs are designed to operate with natural uranium (NU) as the main fuel. Earlier in the initial fresh core, to achieve flux flattening and hence to operate the reactor at design rated power, limited number of depleted uranium bundles were loaded in the central portion of the core. Presently even in fresh core about 40 % of the core is loaded with depleted uranium bundles (?0.6 wt % 235U) from the consideration of conserving the natural uranium fuel. This is achieved by loading most of the depleted bundles in the peripheral locations of the channels. Successful operation with large number of DU bundles in the fresh core has been proven in MAPS - 2 and MAPS - 1cores after EMCCR as well as in TAPP - 4. In these three reactors 100 % FP was possible even with 40 % DU bundles in the core. In TAPP-4 and 3 initial core, ...

2006-11-13

301

Emergency core cooling device for a reactor  

International Nuclear Information System (INIS)

Purpose : To obtain an emergency core cooling device in a FBR type reactor by utilizing heat pipes which are not actuated at usual operation condition but actuated reliably upon emergency. Constitution : A system for injecting heat medium into heat pipes is provided. By injecting the heat medium into the heat pipes upon emergency to actuate the heat pipes, the reactor core is cooled. During normal reactor operation, the inside of the heat pipes is evacuated from a vacuum pump and no heat medium is filled therein, whereby unnecessary heat loss during the normal operation can be prevented. (Ikeda, J.).

1982-01-24

302

Description of odd-A nuclei in the Pt region in the interacting boson-fermion model  

Energy Technology Data Exchange (ETDEWEB)

Properties of unique parity states in odd-proton (/sub 77/Ir, /sub 79/Au) and odd-neutron nuclei (/sub 78/Pt) are investigated in the framework of the interacting boson-fermion approximation model. The core (boson)-particle (fermion) interaction is represented by a quadrupole-quadrupole interaction and an exchange term, which takes into account the effects of the Pauli exclusion principle. The even-even core nucleus is described in terms of the IBA-1 hamiltonian. The change in the properties of the corresponding odd-A nuclei can be interpreted in terms of a transition of the core hamiltonian between the O(6) and SU(3) limiting cases.

1982-05-03

303

Description of odd-A nuclei in the Pt region in the interacting boson-fermion model  

International Nuclear Information System (INIS)

Properties of unique parity states in odd-proton (_7_7Ir, _7_9Au) and odd-neutron nuclei (_7_8Pt) are investigated in the framework of the interacting boson-fermion approximation model. The core (boson)-particle (fermion) interaction is represented by a quadrupole-quadrupole interaction and an exchange term, which takes into account the effects of the Pauli exclusion principle. The even-even core nucleus is described in terms of the IBA-1 hamiltonian. The change in the properties of the corresponding odd-A nuclei can be interpreted in terms of a transition of the core hamiltonian between the O(6) and SU(3) limiting cases. (orig.).

304

Core simulations using actual detector readings for a Canada deuterium uranium reactor  

Science.gov (United States)

This paper reports that, to obtain better simulation results for a Canada deuterium uranium (CANDU) reactor operation, a new simulation method is developed that uses actual detector readings as a correction factor. Detector readings from a CANDU reactor are used to correct the calculated flux distribution during core calculation iterations. A suitable function is found to describe the relationship between the detector flux and the fluxes of mesh points around the detector. The new simulation method is tested by performing numerical calculations for the Wolsung reactor (a CANDU-600). The results show that the new method predicts the core state more accurately with fewer iterations.

1991-02-01

305

Control Rod Ejection Accident while Using 6- and 8-Tube IRT-4M Fuel Assemblies in WWR-SM Research Reactor Core  

Energy Technology Data Exchange (ETDEWEB)

The WWR-SM reactor at the Institute of Nuclear Physics of the Academy of Sciences (INP AS) in Uzbekistan was converted to 6-tube IRT-4M LEU (19.7%) fuel in 2009. Presently, INP intends to also use IRT-4M 8-tube FA, and a safety analysis for these 'mixed' (8-tube and 6-tube FA) cores is required by the regulatory authorities. This paper presents results of control rod ejection transient analysis for these mixed cores

2011-07-01

306

Basic criticality relations for gas core design  

Energy Technology Data Exchange (ETDEWEB)

Minimum critical fissile concentrations are calculated for U-233, U-235, Pu-239, and Am-242m mixed homogeneously with hydrogen at temperatures to 15,000K. Minimum critical masses of the same mixtures in a 1000 liter sphere are also calculated. It is shown that propellent efficiencies of a gas core fizzler engine using Am-242m as fuel would exceed those in a solid core engine as small as 1000L operating at 100 atmospheres pressure. The same would be true for Pu-239 and possibly U-233 at pressures of 1000 atm. or at larger volumes.

1992-05-22

307

caCORE version 3: Implementation of a model driven, service-oriented architecture for semantic interoperability  

British Library Electronic Table of Contents (United Kingdom)

One of the requirements for a federated information system is interoperability, the ability of one computer system to access and use the resources of another system. This feature is particularly important in biomedical research systems, which need to coordinate a variety of disparate types of data. In order to meet this need, the National Cancer Institute Center for Bioinformatics (NCICB) has created the cancer Common Ontologic Representation Environment (caCORE), an interoperability infrastructure based on Model Driven Architecture. The caCORE infrastructure provides a mechanism to create interoperable biomedical information systems. Systems built using the caCORE paradigm address both aspects of interoperability: the ability to access data (syntactic interoperability) and understand the ...

2008-01-01

308

Unearthing the Phylogenetic Roots of Sleep  

UK PubMed Central (United Kingdom)

Why we sleep remains one of the enduring unanswered questions in biology. At its core, sleep can be defined behaviorally as a homeostatically regulated state of reduced movement and sensory...Full Text Available

2008-08-05

309

Temperature measurements of the EK-10 type reactor fuel rods in EWA-4 core  

International Nuclear Information System (INIS)

... ked by ! I ; II III IV Table 4. Temperatute distributions along the fuel rod at a

310

Structural Response of Marine Sandwich Panels to Uniform ...  

Science.gov (United States)

... Composite sandwich panels with fiber reinforced plastic (FRP) faces and low 3 density foam cores are fast becoming the structural material of ...

1990-06-01

311

Quantitative Spectroscopy of Photospheric-Phase Type II SN  

Science.gov (United States)

... and high-quality photospheric-phase Type II SN spectra to constrain core- collapse SN explosions, massive star evolution, and distances in the Universe ...

312

Present status of study on reduced-moderation water reactors  

Energy Technology Data Exchange (ETDEWEB)

The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor, based on the experienced light water reactor (LWR) technology, aiming at effective utilization of uranium resources, high burn-up and long operation cycle and plutonium multiple recycling. These characteristics can be achieved by the high conversion ratio from {sup 238}U to {sup 239}Pu resulted from the higher neutron energy spectrum in comparison to conventional LWRs. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPC) in 1998, under technical cooperation with three Japanese reactor vendors. In the core design study of the RMWR, several basic core designs with the high conversion ratio more than 1 and the negative void reactivity coefficient have been proposed, and then, ...

2001-09-01

313

Power spectral density measurements with "2"5"2Cf for a mockup of the FFTF  

International Nuclear Information System (INIS)

... californium 252 fftf reactor mockup power density reactor cores reactor noise

1975-06-08

314

Power Management for Real-Time Systems  

Science.gov (United States)

... CycleSim models an IBM PowerPC 405GP system-on-a-chip and includes a cycle-accurate, event-based power model of the processor core and ...

2004-07-01

315

PPT - AstroGravS - NASA  

Science.gov (United States)

Form as the end result of massive star evolution; Type II supernova: collapse of iron core in highly evolved massive star; outer regions blasted away in ...

316

Microbiological Comparison of Core and Groundwater Samples Collected from a Fractured Basalt Aquifier with that of Dialysis Chamber Incubated in Situ  

Energy Technology Data Exchange (ETDEWEB)

Microorganisms associated with fractured basalt core were compared to those suspended in groundwater pumped from the same well in the eastern Snake River Plain Aquifer (Idaho, USA). Two wells influenced to different degrees by a mixed-waste plume in the fractured basalt aquifer were examined. In one well, an array of dialysis cells filled with either deionized water or crushed basalt was equilibrated to compare the microorganisms collected in this fashion with those from core and groundwater samples collected in a traditional manner from the same well. Analyses were performed to characterize these samples and to provide a basis for comparison. These included total cell counts by microscopy; total biomass by phospholipid fatty acid analysis; enumerations of viable aerobic heterotrophs, groups of putative aerobic co-metabolic TCE-degraders and aerobic H2-oxidizing bacteria; mineralization of 14C- labeled acetate; and enrichments for dissimilatory ...

2004-04-01

317

Introducing N-glycans into natural products through a chemoenzymatic approach**  

UK PubMed Central (United Kingdom)

The present study describes an efficient chemoenzymatic method for introducing a core N-glycan of glycoprotein origin into various lipophilic natural products. It was found...Full Text Available

2008-11-24

318
319

Families of ellipsoidal stellar systems adn the formation of dwarf elliptical galaxies  

International Nuclear Information System (INIS)

Core radii and central surface brightnesses of bulges and elliptical galaxies are measured using CCD photometry obtained with the Canada-France-Hawaii Telescope (scale = 0''.22 pixel"-"1; seeing = 0''.45--1''.0 FWHM). The correlations between core parameters are derived and compared for ellipticals, bulges, dwarf spheroidal galaxies, dwarf irregular galaxies, and globular clusters. The results are as follows. 1. Ihe data confirm the existence of well-defined correlations between the core parameters of elliptical galaxies. More luminous ellipticals have larger core radii r/sub c/ and lower central surface brightnesses #mu#/sub 0v/. Galaxies with larger core radii have larger central velocity dispersions. The small, bright core of M32 is normal for a galaxy of M/sub B/ = -15.2. Radio ellipticals and brightest cluster galaxies satisfy the correlations. 2. The ...

320

FFTF scale-model characterization of flow-induced vibrational response of reactor internals  

International Nuclear Information System (INIS)

As an integral part of the Fast Test Reactor Vibration Program for Reactor Internals, the flow-induced vibrational characteristics of scaled Fast Test Reactor core internal and peripheral components were assessed under scaled and simulated prototype flow conditions in the Hydraulic Core Mockup. The Hydraulic Core Mockup, a 0.285 geometric scale model, was designed to model the vibrational and hydraulic characteristics of the Fast Test Reactor. Model component vibrational characteristics were measured and determined over a range of 36 percent to 111 percent of the scaled prototype design flow. Selected model and prototype components were shaker tested to establish modal characteristics. The dynamic response of the Hydraulic Core Mockup components exhibited no anomalous flow-rate dependent or modal characteristics, and prototype response predictions were adjudged acceptable.

321

Effect of the repulsive core on the exciton spectrum in a quantum ring  

Energy Technology Data Exchange (ETDEWEB)

A theoretical study of an exciton confined in a quantum ring is presented. The quantum ring is described as a two-dimensional circular quantum dot with a repulsive core, which is modelled with the help of two Gaussian functions. We have applied the variational method and investigated the evolution of the low-energy exciton spectrum with the change of the confinement potential. The calculations have been performed for the recently produced self-assembled ring-shaped InGaAs quantum dots. We have shown that the repulsive core strongly increases the radiative transition probability from the exciton ground state at the expense of the decreasing probability of the transitions from the excited states. This effect results from the orthogonality properties of the exciton wavefunctions, which are specific to the quantum-ring confinement potential. We have studied the characteristic features of the exciton spectrum, which can be used as a signature of the ...

2002-01-14

322

Disruptive core relocation analysis of PHEBUS/FPT0 test with SAMPSON code  

International Nuclear Information System (INIS)

SAMPSON is an integration of twelve analysis modules under the final development phase (phase-2) and will be capable of simulating hypothesized severe accidents in a nuclear power plant. One of these modules, the Molten Core Relocation Analysis (MCRA) module, simulates the relocation behavior of a molten core during a severe accident. MCRA models severe accident phenomena by using mechanistic formulations for multi-phase, multi-component, and multi-velocity field. As one of the verification studies of SAMPSON in Phase-1, the in-core phenomena of PHEBUS/FPT0 was analyzed with three modules, MCRA, fuel rod heat up analysis (FRHA) module, and the analysis control module (ACM) of SAMPSON. (author)

2000-10-01

323

Development of linear sensitivity matrix method for fast evaluation of CANDU refuelling schemes  

International Nuclear Information System (INIS)

In order to develop a numerical tool for the fast evaluation of CANDU refuelling schemes, a Linear Sensitivity Matrix method (LSM) is developed. It assumes that all the effects caused by various perturbations to the core state are independent to each other and the core response to a perturbation is proportional to its magnitude. In this way, the main core parameters of a refuelling scheme can be derived by simple algebraic operations with the use of pre-calculated sensitivity matrices, without resorting to the complicated and time-consuming 3D core calculation. Verification against the Qinshan CANDU reactor operation history demonstrates that LSM is capable of generating accurate results and running very fast for evaluating a refuelling scheme. (authors)

2009-06-01

324

Control device in a reactor  

International Nuclear Information System (INIS)

Purpose: To flatten temperature distribution of coolant within a core. Constitution: The control device of the present invention is to vary reactivity of a fast breeder to control a reactor power. In general, the control device of this kind comprises a guide pipe arranged within the core and a control rod movable up and down within the guide pipe, and a coolant flows from bottom toward top within the guide pipe. Since a cooling flow rate has a margin, temperature of coolant outlet is extremely low as compared to a fuel assembly, and therefore temperature gradient in the vicinity of the top of the control rod becomes sharp to possibly impart thermal shock to the structural material. In the present invention, the flow passage of coolant is varied to thereby avoid outflow thereof into the core, thus flattening the temperature distribution of the coolant within the core. (Kamimura, M.).

325

Computational Fluid Dynamic Analysis of Core Bypass Flow Phenomena in a Prismatic VHTR  

Energy Technology Data Exchange (ETDEWEB)

The core bypass flow in a prismatic very high temperature gas-cooled reactor (VHTR) is one of the important design considerations which impacts considerably on the integrity of reactor core internals including operating fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) will be affected by the bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to understand better the bypass flow phenomenon and establish the evaluation method in the ...

2010-09-01

326

Compression Behavior of Fluted ... - NASA Technical Reports Server  

Science.gov (United States)

Traditional composite sandwich panels are composed of inner and outer facesheets separated by a core material such as balsa wood, polymeric foam, ...

327

Comparisons of the SCDAP computer code with bundle data under severe accident conditions  

International Nuclear Information System (INIS)

The SCDAP computer code, which is being developed under the sponsorship of the United States Nuclear Regulatory Commission, models the progression of light water reactor core damage including core heatup, core disruption and debris formation, debris heatup, and debris melting. SCDAP is being used to help identify and understand the phenomena that control core behavior during a severe accident, to help quantify uncertainties in risk assessment analysis, and to support planning and interpretation of severe fuel damage experiments and data. Comparisons between SCDAP calculations and the experimental data showed good agreement. Calculated and measured bundle temperatures for SFD-ST were within 200 K for the entire bundle and within 20 K for maximum cladding temperatures. For ESSI-2, calculated and measured maximum cladding temperatures were within 50 K, and the extensive liquefaction and relocation that was ...

1983-08-22

328

Commercial Contract Training, Marine Corps Area VOTEC ...  

Science.gov (United States)

... Plaster Foundry facings_ Casting: (Non-ferrous Ferrous Alloy .___) Cupola furnace Core baking oven_ _ Metallurgy__ Thermite casting__ ...

1975-06-01

329

Calculation of model neutron stars with pion condensation  

Energy Technology Data Exchange (ETDEWEB)

It is shown numerically that on a time scale of order 1 msec a neutron star with pion condensation will undergo separation into a core and an envelope with a sharp interface. The envelope will not, however, be ejected.

1982-01-01

330

Brief summary of reactor core component welding for the Fast Flux Test Facility (FFTF)  

International Nuclear Information System (INIS)

Included are descriptions of welding methods and joint design, welding equipment, and qualification tests.

1974-04-25

331

Ancient Pollen Yields Insight into Forest Biodiversity  

Science.gov (United States)

... data on pollen from red maple, birch, beech, ash, oak, hemlock and elm trees isolated from cores of ...

332

AeroSpace Information for a Changing World - NASA Technical ...  

Science.gov (United States)

Mar 1, 2011 ... thermal behavior and structural changes of composite sandwich panels with a honeycomb core subjected to a variety of environmental effects. ...

333

A Search for Core-Collapse Supernova Progenitors in Hubbk Space - NASA  

Science.gov (United States)

for massive star evolution, or they could all be very blue super- giant stars experiencing A , = 1-1.5 mag. The fact that the en- ...

334

The formation of counterrotating cores in elliptical galaxies  

International Nuclear Information System (INIS)

The mechanism proposed by Kormendy (1984) for the formation of counterrotating cores in elliptical galaxies is investigated using self-consistent numerical simulations of mergers between a high- and a low-luminosity elliptical galaxies. The conditions for a counterrotation to appear are determined, observational properties of the remnants are described, and the evolution of the structural and kinematic parameters of the larger galaxy is analyzed. It is shown that a counterrotation results only when the merging orbits are retrograde, due to a large change in the secondary spin during the merger. 36 refs.

335

Possible stellar evolutionary link to black holes  

Science.gov (United States)

The suggestion has been made that stars with collapsing iron cores may be unable to explode, and hence may generate black holes. The situation when the collapsing core is rotating and magnetized is investigated and it is tentatively concluded that these effects make the situation even more conducive to the formation of black holes. (auth)

1973-10-01

336

Near-Core and In-Core Neutron Radiation Monitors for Real Time Neutron Flux Monitoring and Reactor Power Level Measurements  

Energy Technology Data Exchange (ETDEWEB)

MPFDs are a new class of detectors that utilize properties from existing radiation detector designs. A majority of these characteristics come from fission chamber designs. These include radiation hardness, gamma-ray background insensitivity, and large signal output.

2006-06-12

337

Irradiation test program for FFTF  

International Nuclear Information System (INIS)

Four unique deisgn features are described which make the Fast Flux Test Facility eminently suitable for irradiation test programs. These features are a fast flux level of 7 x 10"1"5 neutrons/cm"2/sec, a 36-inch reference (breeder reactor) core height, test volumes suitable for testing of statistical quantities of materials, and the capability for direct (contact) or indirect (proximity) instrumentation of active core experiments.

338

Helicoidal instability of a scroll vortex in three-dimensional reaction-diffusion systems  

International Nuclear Information System (INIS)

We study the dynamics of scroll vortices in excitable reaction-diffusion systems analytically and numerically. We demonstrate that intrinsic three-dimensional instability of a straight scroll leads to the formation of helicoidal structures. This behavior originates from the competition between the scroll curvature and unstable core dynamics. We show that the obtained instability persists even beyond the meander core instability of the two-dimensional spiral wave. copyright 1998 The American Physical Society.

1998-10-01

339

Experience with Aerosol Generation During Rotary Mode Core Sampling in the Hanford Single Shell Waste Tanks  

Energy Technology Data Exchange (ETDEWEB)

This document provides data on aerosol concentrations in tank headspaces, total mass of aerosols in the tank headspace, and mass of aerosols sent to the exhauster during rotary mode core sampling from November 1994 through June 1999. A decontamination factor for the RMCS exhauster filter housing is calculated based upon operational data and non-destructive assay.

2001-03-23

340

Experience with Aerosol Generation During Rotary Mode Core Sampling in the Hanford Single Shell Waste Tanks  

Energy Technology Data Exchange (ETDEWEB)

This document provides data on aerosol concentrations in tank head spaces, total mass of aerosols in the tank head space and mass of aerosols sent to the exhauster during Rotary Mode Core Sampling from November 1994 through June 1999. A decontamination factor for the RMCS exhauster filter housing is calculated based on operation data.

2000-01-24

341

Effect of #beta#_4 deformations on decoupled rotational bands in odd-A nuclei  

International Nuclear Information System (INIS)

Calculations for a single-j nucleon coupled to an axially symmetric core with both #beta#_2 and #beta#_4 deformation have been performed for "1"8"7Ir. Using #beta#_4=-0.08, consistent with previously measured and predicted values of #beta#_4, the calculated spectrum is competitive with recent calculations assuming an asymmetric core.

342

Downward penetration of hot UO/sub 2/ into basalt concrete  

Energy Technology Data Exchange (ETDEWEB)

Following a postulated meltdown accident, the integrity of containment building structural material under attack by hot molten core debris and the safeguard of environment against radiological releases constitutes the final line of defense in PAHR safety assessment. Such assessment requires a good knowledge of UO/sub 2//interaction and penetration with different types of concrete. The present study focuses on the phenomena associated with core debris interaction/penetration with substrate basalt concrete.

1983-01-01

343

Determination of reactor kinetic parameters in a two-core reactor  

Energy Technology Data Exchange (ETDEWEB)

The kinetic parameters, ..cap alpha.. the coupling coefficient and tau-bar the mean neutron transit time have been determined using a reactor oscillator on the coupled-core of the Queen Mary College research reactor. By using correlation techniques it has proved possible to use detectors small enough to be inserted in the fuel tanks. It is shown that the simplified Baldwin model with one-group diffusion theory is inadequate to describe the kinetic behaviour and the experimentally-determined parameters are dependent upon the positioning of the detectors.

1982-01-01

344

Detection and Isolation of Ultrasmall Microorganisms from a 120,000-Year-Old Greenland Glacier Ice Core  

UK PubMed Central (United Kingdom)

The abundant microbial population in a 3,043-m-deep Greenland glacier ice core was dominated by ultrasmall cells (<0.1 μm3) that may represent intrinsically small organisms...Full Text Available

2005-12-01

345

Destabilization of the hot-electron precessional mode in tandem mirrors and bumpy tori  

International Nuclear Information System (INIS)

The high-frequency precessional mode of a hot-electron-stabilized magnetic configuration has previously been shown to be stable in a window of core-plasma mass. Under conditions of frequency matching, the resulting stable negative-energy precessional wave can be destabilized by coupling to positive-energy shear-Alfven waves. Coupling is avoided when the hot-electron precession frequency exceeds the core-plasma ion gyrofrequency.

346

Core power distribution measurement and data processing in Daya Bay Nuclear Power Station  

International Nuclear Information System (INIS)

For the first time in China, Daya Bay Nuclear Power Station applied the advanced technology of worldwide commercial pressurized reactors to the in-core detectors, the leading excore six-chamber instrumentation for precise axial power distribution, and the related data processing. Described in this article are the neutron flux measurement in Daya Bay Nuclear Power Station, and the detailed data processing.

347

Safety System Design Concept and Performance Evaluation for a Long Operating Cycle Simplified Boiling Water Reactor  

Science.gov (United States)

The long operating cycle simplified boiling water reactor is a reactor concept that pursues both safety and the economy by employing a natural circulation reactor core without a refueling, a passive decay heat removal, and an integrated building for the reactor and turbine. Throughout the entire spectrum of the design basis accident, the reactor core is kept covered by the passive emergency core cooling system. The decay heat is removed by the conventional active low-pressure residual heat removal system. As for a postulated severe accident, the suppression pool water floods the lower part of the reactor pressure vessel (RPV) in the case when core damage occurs, and the in-vessel retention that keeps the melt inside the RPV is achieved by supplying the coolant. The containment adopts a parallel-double-steel-plate structure similar to a hull structure, which contains coolant between the inner and outer ...

2003-07-15

348

Radiological safety aspects associated with the handling, storage and disposal of self power neutron detectors in TAPS - 3 and 4  

International Nuclear Information System (INIS)

At Tarapur Atomic Power Station 3 and 4, 540 MWe Pressurised Heavy Water Reactors, core being large in size requires a continuous in core monitoring for local flux disturbances. Nearly 200 Self Powered Neutron Detectors (SPNDs) of the Straight Individually Replaceable (SIR) type are distributed in the reactor core. For purpose of reactor regulation and protection, cobalt SPNDs that have a prompt response for changes in power is used for in-core flux mapping, vanadium SPNDs that provide accurate measure of neutron flux, even though having slow response is used In core SPNDs are placed in Vertical Flux Units (VFU) and Horizontal Flux Units (HFUs). These SPNDs were to be replaced at regular intervals to meet the design intent. Cobalt SPNDs have dose rates of the order of 1000 Gy/h and the Mineral Insulated (MI) cables of Vanadium SPNDs have dose rates of the order of 100 Gy/h. So far 3 ...

2006-11-13

349

Microsegregation-related pitting corrosion characteristics of AL-6XN superaustenitic stainless steel laser welds  

International Nuclear Information System (INIS)

Research highlights: #-># Welding parameters affect pitting corrosion resistance of AL-6XN laser welds. #-># Lower heat input laser welds correspond to higher critical pitting temperature. #-># Depletion of Mo and Cr at dendrite cores causes preferential pitting corrosion. #-># Local Mo level at dendrite cores dominates weld pitting corrosion susceptibility. #-># Lower heat input laser welds manifest lower degree of microsegregation of Mo. - Abstract: Pitting corrosion resistance of laser welds of AL-6XN superaustenitic stainless steel (SASS) was investigated in acidic chloride ion medium. It was found that the critical pitting temperature (CPT) of the laser welds increased with increasing welding speed or decreasing laser power. Pitting attack preferentially occurred at selective dendrite cores of the laser welds. Analytical electron microscope (AEM) microanalysis revealed that depletion of Mo at dendrite ...

2010-10-01

350

Internal stresses analysis in telectroformed nickel shells for thermoplastics injection mold core (rapid tooling); Analisis de las tensiones internas en las cascaras de niquel electroconformadas que se utilizan como inserto de un molde de inyeccion de termoplasticos (rapid tooling)  

Energy Technology Data Exchange (ETDEWEB)

This study deals with a research field started at the LFI (Laboratorio de Fabricacion Integrada) of the ULPGC (Universidad de Las Palmas de Gran Canaria). Its aim is to analyse and propose improvements in the electroformed nickel cores manufacture. The main application of these cores is to be used as plastic injection molds. It has been considered an important part of this study taking under consideration internal stresses that appear in the nickel electroformed core. These stresses play a determinant role towards reaching a dimensional and resistant quality standard of the shells, which will be later transformed into cores. The investigation includes not only a theoretic study but also an experimental one. the testing method has the remarkable advantage of a wide industrial application because of its simplicity, low cost and reproducibility of the electrolytic bath actual conditions. (Author) 7 refs.

2005-07-01

351

Emergency core cooling device  

International Nuclear Information System (INIS)

Purpose: To effectively cool the reactor core in a steam atmosphere by upwardly directing several of spray nozzles attached to a ring header thereby increasing the flying distance of the spray. Constitution: Ring headers in two upper and lower stages are disposed above the outer circumference of a reactor core and each of the ring headers is mounted with spray nozzles. Among the spray nozzles, at least several nozzles mounted to the ring header at the lower stage are directed such that the center axis for each of the nozzle is raised above the horizontal axis and other several nozzles are mounted with the nozzle center axis directed downwardly from the horizontal axis. Accordingly, even if collapsing phenomenon occurs in the jetting stream due to the condensation in the steams that forms the operation atmosphere of the reactor core spray cooling device, a sufficient amount of emergency cooling water can be distributed over ...

1983-03-09

352

Comparison of the SASSYS/SAS4A radial core expansion reactivity feedback model and the empirical correlation for the FFTF  

International Nuclear Information System (INIS)

The present emphasis on inherent safety for liquid-metal reactor designs has resulted in a need to represent the various reactivity feedback mechanisms as accurately as possible. The dominant negative reactivity feedback has been found to result from radial expansion of the core for most postulated anticipated transient without scram events. For this reasons, a more detailed model for calculating the reactivity feedback from radial core expansion, including subassembly bowing has been recently developed for use with the SASSYS/SAS4A code system. The purpose of this summary is to present an extension to the model so that it is more suitable for handling a core restraint design as used in the Fast Flux Test Facility (FFTF), and to compare the SASSYS/SAS4A results using this model to the empirical correlation presently being used to account for radial core expansion reactivity feedback in the FFTF.

1987-11-15

353

Toward Improving Prediction of Sediment Transport over Wave-Induced Ripples  

CERN Document Server

Sediment transport over wave-induced ripples is a very complex phenomenon where available models fail to provide accurate predictions. For coastal engineering applications, the 1-DV advection-diffusion equation could be used with an additional parameter {\\alpha} related to the process of vortex shedding above ripples (Absi, 2010). The aim of this study is to provide simple practical analytical tools. An analytical eddy viscosity profile was validated by DNS data of turbulent channel flows (Absi et al., 2011). In this study, we will show that: (1) the period-averaged eddy viscosity in oscillatory boundary layers could be described by this simple analytical formulation; (2) The shape of the vertical profile is validated by period-averaged eddy viscosity of baseline (BSL) k-{\\omega} model (Suntoyo and Tanaka, 2009) for sinusoidal and asymmetric waves; (3) The vertical eddy viscosity profile depends on the wave non-linearity parameter and requires therefore a ...

2011-01-01

354

Residential runoff as a source of pyrethroid pesticides to urban creeks.  

Science.gov (United States)

Pyrethroid pesticides occur in urban creek sediments at concentrations acutely toxic to sensitive aquatic life. To better understand the source of these residues, runoff from residential neighborhoods around Sacramento, California was monitored over the course of a year. Pyrethroids were present in every sample. Bifenthrin, found at up to 73 ng/L in the water and 1211 ng/g on suspended sediment, was the pyrethroid of greatest toxicological concern, with cypermethrin and cyfluthrin of secondary concern. The bifenthrin could have originated either from use by consumers or professional pest controllers, though the seasonal pattern of discharge from the drain was more consistent with professional use as the dominant source. Stormwater runoff was more important than dry season irrigation runoff in transporting pyrethroids to urban creeks. A single intense storm was capable of discharging as much bifenthrin to an urban creek in 3h as that discharged ...

2008-08-03

355

Residential runoff as a source of pyrethroid pesticides to urban creeks  

International Nuclear Information System (INIS)

Pyrethroid pesticides occur in urban creek sediments at concentrations acutely toxic to sensitive aquatic life. To better understand the source of these residues, runoff from residential neighborhoods around Sacramento, California was monitored over the course of a year. Pyrethroids were present in every sample. Bifenthrin, found at up to 73 ng/L in the water and 1211 ng/g on suspended sediment, was the pyrethroid of greatest toxicological concern, with cypermethrin and cyfluthrin of secondary concern. The bifenthrin could have originated either from use by consumers or professional pest controllers, though the seasonal pattern of discharge from the drain was more consistent with professional use as the dominant source. Stormwater runoff was more important than dry season irrigation runoff in transporting pyrethroids to urban creeks. A single intense storm was capable of discharging as much bifenthrin to an urban creek in 3 h as that discharged ...

2009-01-01

356

Reactor blockage and catalyst and coal ash balances in the direct hydroliquefaction of coal in a tubular reactor  

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the reactor blockages occurring in the course of direct hydroliquefaction of Miike coal, Taiheiyo coal and Yallourn coal briquets in a tubular reactor. The liquefaction tests were carried out at 450 C under 24.6 MPa hydrogen pressure, with red mud and sulfur catalyst. From the observed balances for catalyst and coal ash, it was inferred that reactor blockages are due to sedimentation of catalyst and ash. The conditions for catalyst and coal ash run-off were determined after solvent and slurry flow rates had been altered to suit the type of coal being tested. It was found that ash run-off occurred more readily as the difference between the slurry flow velocity and the natural sedimentation velocity of red mud in the coal liquids increased. Even when ash run-off was occurring, however, the ash concentration of the slurry in the reactor was higher than the concentration in the feed slurry. This is taken as indicating that ...

1984-01-01

357

Nature of arrangement of buried reefs and bioherms in the Lower Permian deposits of the Dnieper Donets Basin  

Energy Technology Data Exchange (ETDEWEB)

In the Assel'skiy and Sakmarskiy time of the lower Permian epoch, on the territory of the modern Dnieper and Donets, and Pripyatskiy Basins, there was a gulf which stretched in a northwest direction. The latter connected to the open sea in the east through the CisDonets trough. Transverse tectonic elevations divided the gulf into 5 semi-isolated reservoirs. In the Assel'skiy time, in the period of carbonate sedimentation, the development of algae, crinoids, corals and other organisms occurred. They created reef, bioherm and biostroma reconstructions. The most favorable sections for their settlement were the coastal zones of the gulf, consedimentation positive structures and transverse tectonic elevations. It is assumed that the formation of reefs, bioherms and biostromas, on the one hand, and sedimentation of evaporites on the other hand, are interrelated processes. The first after the next marine transgression during their ...

1981-01-01

358

Fluorimetric determination of uranium in certain refractory minerals, environmental samples and industrial waste materials  

International Nuclear Information System (INIS)

A simple sample decomposition and laser fluorimetric determination of uranium at trace level is reported in certain refractory minerals, like ilmenite, rutile, zircon and monazite; environmental samples viz. soil and sediments; industrial waste materials, such as, coal fly ash and red mud. Ilmenite sample is decomposed by heating with ammonium fluoride. Rutile, zircon and monazite minerals are decomposed by fusion using a mixture of potassium bifluoride and sodium fluoride. Environmental and industrial waste materials are brought into solution by treating with a mixture of hydrofluoric and nitric acids. The laser induced fluorimetric determination of uranium is carried out directly in rutile, zircon and in monazite minerals and after separation in other samples. The determination limit was 1 #mu#g x g"-"1 for ilmenite, soil, sediment, coal fly ash and red mud samples, and it is 5 #mu#g x g"-"1 for rutile, zircon and monazite. The method is also ...

2005-10-01

359

Facial osteomyelitis as complication of chronic sinusitis in hemophiliac-AIDS patients - scintigraphic evaluation with technetium-99m-MDP and Gallium-67; Osteomielitis da face como complicacao de sinusite cronica em hemofilicos aideticos - avaliacao cintilografica com {sup 99m} Tc-MDP e {sup 67} Ga  

Energy Technology Data Exchange (ETDEWEB)

In the paper six cases of facial osteomyelitis as a complication of chronic sinusitis in hemophiliac-AIDS patients are reported. Osteomyelitis was suggested by an increasing of erythrocyte sedimentation rate. The diagnosis was confirmed by a positive {sup 99m} Tc MDP scintigraphy. The patients were submitted to clinical treatment. The erythrocyte sedimentation rate and 67-gallium citrate scans were used in the follow-up of the therapy. Three patients had negative gallium after three weeks of organism-specific antibiotic therapy; in two patients the gallium scintigraphy remained positive. One patient did not undergo the radionuclide scan for this clinical conditions. These results suggest that MDP scans showed higher sensitivity and specificity in detection of bone disease in chronic sinusitis. Gallium scans appeared to be valuable tool in the follow-up of the infection. There are no reports in the literature of osteomyelitis as a complication ...

1997-01-01

360

Chemical source identifications for natural resource injury/damage assessments and site assessments  

International Nuclear Information System (INIS)

Current regulations guiding technical aspects of natural resource damage assessments combine source, exposure pathway, resource injury, and monetary damage components. In order to associate any observed injury to the uncontrolled release of chemicals (e.g. oil spills, contaminated sediments, in-place toxics, etc.), it is important to link the chemical ''release'' to the injured resource. In complex environmental settings where multiple sources of similar chemicals are combined, multicomponent chemical methods must be used to link the release to the environmental distribution of chemicals. Three examples of the utility of multicomponent organic chemical analyses linked to comprehensive and representative sampling strategies will be discussed--the Shell Martinez Refinery oil spill, the Exxon Valdez oil spill, and a contaminated sediment assessment. These NRDA-based source identifications are based on use of polycyclic aromatic hydrocarbons, ...

1993-11-14

361

Biogeochemical cycling of N in tropical coastal zones: molecular microbial ecology of trace gas production.  

Environmental Research Database

ObjectivesThe specific objectives of the research are to: 1. Determine the concentrations of N2O, NO and NO2 in tropical coastal waters in relation to nutrients and salinities. 2. Determine, with excess nitrate present, the potential for nitrate reduction and denitrification in sediments along tropical estuaries, and whether NO, NO2, N2O, N2 or NH4+ are significant products. 3. Establish the balance between denitrification, nitrate ammonification and anammox in tropical estuarine sediments, relative to [continued...]DescriptionThe coastal zone is extremely important in the biogeochemical processes which control the natural cycle of elements of the Earth. In particular, the coastal zone contributes significantly to the nitrogen cycle, removing nitrogen washed in from the land by rivers and so reducing its fertilizing impact on the coastal seas. However, these removal processes, driven by microorganisms, also contribute to the formation of ...

2009-01-31

362

Age sensitivity of juvenile mussels (Utterbackia imbeciles Say) to copper and cadmium exposure  

Energy Technology Data Exchange (ETDEWEB)

In recent years, there has been increased interest in using early life stages of freshwater bivalves to test the toxicity of dissolved constituents in water. The authors have developed laboratory and in situ assays with artificially cultured Utterbackia imbecillis to examine effects of contaminants and existing conditions in embayments and rivers on mortality and reproductive success of unionid mussels. Age sensitivity of U. imbecillis to Cd and Cu was examined using both static acute and 8-day static renewal bioassays. Both aqueous and sediment exposures demonstrated greater sensitivity to Cd than Cu. LC{sub 50}`s for two-day old (2d) and 9d mussels were approximately half the LC{sub 50} calculated for 16d mussels in 48-hr bioassays with Cd. Additionally, acute assays were repeated twice to examine variability in response between different mussel cultures to the two metals. The results of this work reinforce the potential of juvenile U. imbecillis as a standard ...

1994-12-31

363

Zonal, provincial, lithological, and geomorphic features of soil salinization in the Southern federal okrug of Russia  

British Library Electronic Table of Contents (United Kingdom)

The relationships between soil salinization and the zonal and provincial bioclimatic conditions, the lithological composition of the sediments, and the geomorphic features of the territory have been analyzed for the Southern federal okrug of Russia. It is shown that the lithological and geomorphic conditions (relief, salinity of parent materials, degree of drainage, and the depth of saline groundwater) play an important role in the distribution of salt-affected soils against the background of the more general regularities specified by the climate. The participation of salt-affected soils in the soil cover of the Southern federal okrug increases in the eastward direction from the forest-steppe zone to the semidesert zone in agreement with an increase in the aridity and continentality of the...

2011-01-01

364

The use of the isotope "3"2P in the study of some ecological aspects of a laboratory stream ecosystem  

International Nuclear Information System (INIS)

A laboratory stream consisting of two stream sections interrupted by two pools was filled with a mixture of tap water and organically enriched water from rivers nearby. Bottom sediment material, Potamogeton pectinatus, macro-invertebrate organisms, as well as the mosquito fish, Aplocheilichthys johnstonii were collected from rivers around Johannesburg and introduced into the laboratory stream. After initial acclimatization, the distribution of the isotope "3"2P through this laboratory stream was followed. Absorption of this isotope by benthic algae, Potamogeton pectinatus, several macro-invertebrate organisms as well as Aplocheilichthys johnstonii was recorded.

365

Spectrometric techniques application to study of environmental contamination levels in south Shetland Antarctic  

International Nuclear Information System (INIS)

The methodology for studying the behaviour of the toxic pollutant metals (Hg, Pb, Cd, Cr) in the South Shetland region is presented here, toxic pollutants are caused by the urban and industrial activity at the Southern hemisphere and they are pressured to be incorporated to the region though atmospheric transport processes the Cs 137 (refI) was used as a tracing element, which was freed and dispersed in the atmosphere as a result of nuclear bombs testing. During the austral summer samples from ground, sediments, atmospheric and glacier were extracted.

366

Review of the Vortec soil remediation demonstration program  

Energy Technology Data Exchange (ETDEWEB)

The DOE`s clean-up of its nuclear complex require the development of innovative technologies to convert soils contaminated by hazardous and/or radioactive wastes to forms which can be readily disposed in accordance with current waste disposal methods. The unique features of Votec CMS technology should make it particularly cost-effective process for the vitrification of soils, sediments, sludges, and mill tailings containing organic metallic and/or radioactive contaminants. This article describes the technology (Votec`s combustion and melting system), the results of testing, the demonstration plant system, and summarizes the future schedule and the equipment needed. 3 figs., 3 tabs.

1994-11-01

367

Quantification of uranium transport away from firing sites at Los Alamos National Laboratory: A mass balance approach  

Science.gov (United States)

Investigations were conducted at Los Alamos National Laboratory to quantify the extent of migration of depleted uranium away from firing sites. Extensive sampling of air particles, soil, sediment, and water was conducted to establish the magnitude of uranium contamination throughout one watershed. The uranium source term was estimated, and mass balance calculations were performed to compare the percentage of migrated uranium with original expenditures. Mass balance calculations can be powerful in identification of the extent of waste migration and used as an aid in planning future waste investigations.

1992-02-01

368

JEFI OLD: Joint seismic/electrical measurement of gas hydrate content in continental margin sediments  

Environmental Research Database

ObjectivesNot EnteredDescriptionMethane hydrate in an ice-like substance consisting of molecules of methane gas combined chemically with water. It is stable at high pressures and low temperatures. Since the ocean floor is normally cold, but temperatures increase with depth inside the Earth, such conditions normally prevail for a few hundred meters below the seafloor where the ocean depth is more than a few hundred metres. Methane beneath the ocean floor is formed by the decomposition of organic material. At the edges of the co [continued...

2006-01-30

369

In Situ Remediation of {sup 137}Cs Contaminated Wetlands Using Naturally Occurring Minerals  

Energy Technology Data Exchange (ETDEWEB)

Cesium-137 has contaminated a large area of the wetlands on the Savannah River Site. Remediation of the contaminated wetlands is problematic because current techniques destroy the sensitive ecosystem and generate a higher dose to workers. To address this problem, we proposed a non-trusive, in situ technology to sequester 137Cs in sediments. One intention of this study was to provide information regarding a go/no go decision for future work. Since the proof-of-concept was successful and several minerals were identified as potential candidates for this technology, a go decision was made.

1999-08-11

370

ISDD: A Computational Model of Particle Sedimentation, Diffusion and Target Cell Dosimetry for In Vitro Toxicity Studies  

Energy Technology Data Exchange (ETDEWEB)

Background: The difficulty of directly measuring cellular dose is a significant obstacle to application of target tissue dosimetry for nanoparticle and microparticle toxicity assessment. As a consequence, the target tissue paradigm for dosimetry and hazard assessment of nanoparticles has largely been ignored in favor of using metrics of exposure (e.g. ?g particle/mL culture medium, particle surface area/mL, particle number/mL). We have developed a computational model of solution particokinetics (sedimentation, diffusion) and dosimetry for non-interacting spherical particles and their agglomerates in monolayer cell culture systems. Particle transport to cells is calculated by simultaneous solution of Stokes Law (sedimentation) and the Stokes-Einstein equation (diffusion). Results: The In vitro Sedimentation, Diffusion and Dosimetry model (ISDD) was tested against measured transport rates or cellular doses for multiple sizes ...

2010-11-30

371

Heat storage composition  

Energy Technology Data Exchange (ETDEWEB)

A heat storage compostion comprises sodium sulfate decahydrate as main component, a supercooling inhibitor, and a solid-liquid separation inhibitor. The composition is characterized in that hydraulic calcium sulfate and/or calcium sulfate dihydrate is contained as the solid-liquid separation inhibitor in an amount of 2-15 wt% base on the whole weight of the composition, whereby the solid-liquid separation, i.e. the sedimentation of the anhydrous sodium sulfate during the phase transition, is effectively prevented and the long-term stability is improved. The long-term stabilty of the composition can be more improved by addition of a silcia series of thickener.

1987-05-05

372

Geothermal resource assessment of the New England states  

Energy Technology Data Exchange (ETDEWEB)

With the exception of Sand Springs in Williamstown, Massachusetts, there are no identifiable hydrothermal geothermal resources in the New England region. The radioactive plutons of the White Mountains of New Hampshire do not, apparently, contain sufficient stored heat to make them a feasible target for an induced hydrothermal system such as exists at Fenton Hill near Los Alamos, New Mexico. The only potential source of low grade heat is the large volume of ground water contained within the unconsolidated sediments related to the Pleistocene glaciation of the region. During the course of the survey an unusual and unexplained thermal anomaly was discovered in St. Johnsbury, Vermont, which is described.

1982-01-01

373

Dispersion study of cesium-137 radionuclide in ocean; Estudo da dispersao do radionuclideo cesio-137 nos oceanos  

Energy Technology Data Exchange (ETDEWEB)

A study for Cs-137 radionuclide dispersion in the marine environment through of compartmental model (Box Model) is presented. The model simulates the surface water contamination caused by direct atmospheric deposition, surface wash off, desorption from sediments and transfer with the ground water of accidentally released radionuclides. For this study the model was applied to the North Sea, near to Sellafield, based on the transfer coefficients obtain at the literature. The results obtained are in good agreement with the literature, being that the model developed can be applied in to the brazilian coastal regions. (author). 7 refs, 7 figs.

1995-12-31

374

An Evaluation of Dual-Media Contaminant Transport for SRS Environmental Applications  

Science.gov (United States)

The dual-media approach to contaminant transport modeling has emerged over the years as a clear improvement over the conventional Fickian advection-dispersion, or single-medium model, in an increasing number of settings. Recent application to the MADE-2 tracer test at Columbus Air Force Base has extended interest to field-scale plume migration in unconsolidated sediments. Subsequent application to tritium migration from the SRS F- and H-area seepage basins within this study also demonstrated improved transport predictions.

2002-12-19

375

Aerial gamma ray and magnetic survey, Mississippi and Florida airborne survey: Lake Charles and Port Arthur quadrangles of Louisiana and Texas. Final report  

International Nuclear Information System (INIS)

The Lake Charles and Port Arthur quadrangles cover approximately 10,950 square miles of land west of the Mississippi River delta area. The area overlies thick sections of the Gulf of Mexico Basin. Surficial exposures are dominated by Recent and Pleistocene sediment. A search of available literature revealed no known uranium deposits. A total of 82 uranium anomalies were detected and are discussed briefly in this report. None were considered significant and all appear to relate to cultural features. Magnetic data appear to be in agreement with existing structural interpretations of the area.

376

6. Sample preparation for determining pollutants in components of the environment  

International Nuclear Information System (INIS)

Examples are given of reference materials for radionuclide X-ray fluorescence analysis (RXFA) of the environment processed by the National Bureau of Standards and the IAEA. Methods are described used for preparing standard materials for RXFA. For determining air pollutants the sample is prepared by dry or wet mineralization. Water samples have to be preserved prior to analysis. Insoluble components are separated by filtration or centrifugation. Biological materials must be dehydrated and homogenized. Samples of soil, sludges, sediments and solid wastes will sometimes have to be converted into a solution in some cases a leachate will have to be obtained. (ES).

1983-12-01

377

Transfer of 137Cs and 60Co in a waste retention pond with emphasis on aquatic insects  

International Nuclear Information System (INIS)

The objectives of this research were (1) to analyze the transfers of 137Cs and 60Co in a retention pond, with emphasis on aquatic insects and (2) to determine if detectable concentrations of these radionuclides are exported by emerging aquatic insects. We analyzed the radionuclide concentrations in the following components: water solution, bottom sediments, suspended particulate matter, plankton, floating mats of filamentous algae, benthic macroinvertebrates, and emerging aquatic insects. Samples were collected quarterly from June 1981 to April 1982. The lowest concentrations (in picocuries per milliliter) occurred in solution (range: 1.4 X 10(2) to 3.2 X 10(2) for 137Cs and 8.1 X 10(-1) to 2.2 X 10(0) for 60Co). The highest concentrations (in picocuries per gram dry weight) occurred in the sediments (range: 1.5 X 10(4) to 1.1 X 10(8) for 137Cs and 1.0 X 10(2) to 4.3 X 10(6) for 60Co). The primary producers and aquatic insect consumers had ...

378

Responses of aquatic organisms to metal pollution in a lowland river in Flanders: A comparison of diatoms and macroinvertebrates  

International Nuclear Information System (INIS)

The role of macroinvertebrates and diatoms as indicator for metal pollution was investigated by assessing both biota along a metal gradient in the Belgian river the Dommel. Macroinvertebrates and diatoms were sampled in summer and winter and physical-chemical characteristics of the water were measured at four different sample periods and related to sediment characteristics. Although metal concentrations, except cadmium, in the water nowhere exceeded water quality standards, high metal concentrations were measured in the sediment, indicating historical contamination of the Dommel. At the sites that were situated downstream of the pollution source, high levels of conductivity and chloride were measured in the water. Redundancy Analysis (RDA) indicated pH, phosphate and zinc as the significant environmental variables explaining each respectively 7.7%, 11.6% and 22.6% of the macroinvertebrate community composition. Two clusters could be separated, ...

2008-12-15

379

Oxidation and adsorption of Co(II) EDTA{sup 2-} complexes in subsurface materials with iron and manganese oxide grain coatings  

Science.gov (United States)

Batch interaction experiments were performed under aerobic conditions to characterize the adsorption behavior and valence speciation of CoEDTA complexes (equimolar at 10{sup -5} mol/L) in a series of Pliocene subsurface sediments containing various amounts of Fe and Mn oxides. The experiments were performed in 0.003 mol/L Ca(ClO{sub 4}){sub 2} with a solids concentration of 500 g/L at variable pH (4-9) and at the natural pH of the sediments (pH = 8.3). Three of these subaerial sediments (Ringold 1, 2, 3) contained significant quantities of extractable Fe and Mn, while the fourth (Ringold 4) was virtually devoid of sesquioxide precipates. Microscopic and mineralogic analyses of the most heavily encrusted material (Ringold 2) showed that the oxides existed as intergrain cements and contained crystalline goethite and rancieite/todorokite. Adsorption on a synthetic analog sorbent (0.6 mass% ferrihydrite-coated sand) over a ...

1995-11-01

380

Methane emission to the atmosphere through emergent cattail (Typha latifolia L.) plants  

Energy Technology Data Exchange (ETDEWEB)

Methane (CH{sub 4}) produced microbially in sediments of marshes is emitted to the atmosphere primarily by flowing through and out of emergent aquatic plants. The magnitude of such emission rates and factors controlling those rates are not well understood. We evaluated CH{sub 4} emission from the widely distributed aquatic emergent plant cattail (Typha latifolia L.) in several wetlands in the United States using a field gas-exchange system that concurrently estimated stomatal aperture (i.e., conductance) on the surface of leaves and net photosynthesis. We compared gas exchange among plants of different age and from sites with different soil and atmospheric conditions. The mean rate of CH{sub 4} emission was 0.22{mu}mol m{sup -2} [leaf] s{sup -1}, which is 940 mg CH{sub 4} m{sup -2} d{sup -1} on a ground-area basis, with individual rates ranging from 0.01 to 1.49 {mu}mol m{sup -2} [leaf] s{sup -1}. For individual plants, we found emission rates were (i) highest for ...

1995-11-01

381

Groundwater penetrating radar and high resolution seismic for locating shallow faults in unconsolidated sediments  

Energy Technology Data Exchange (ETDEWEB)

Faults in shallow, unconsolidated sediments, particularly in coastal plain settings, are very difficult to discern during subsurface exploration yet have critical impact to groundwater flow, contaminant transport and geotechnical evaluations. This paper presents a case study using cross-over geophysical technologies in an area where shallow faulting is probable and known contamination exists. A comparison is made between Wenner and dipole-dipole resistivity data, ground penetrating radar, and high resolution seismic data. Data from these methods were verified with a cone penetrometer investigation for subsurface lithology and compared to existing monitoring well data. Interpretations from these techniques are compared with actual and theoretical shallow faulting found in the literature. The results of this study suggests that (1) the CPT study, combined with the monitoring well data may suggest that discontinuities in correlatable zones may indicate that faulting ...

1993-12-31

382

Functional and physical molecular size of the chicken hepatic lectin determined by radiation inactivation and sedimentation equilibrium analysis  

Energy Technology Data Exchange (ETDEWEB)

Radiation inactivation and sedimentation equilibrium analysis were used to determine the functional and physical size of the chicken hepatic membrane receptor that binds N-acetylglucosamine-terminated glycoproteins. Purified plasma membranes from chicken liver were irradiated with high energy electrons and assayed for 125I-agalactoorosomucoid binding. Increasing the dose of ionizing radiation resulted in a monoexponential decay in binding activity due to a progressive loss of binding sites. The molecular mass of the chicken lectin, determined in situ by target analysis, was 69,000 +/- 9,000 Da. When the same irradiated membranes were solubilized in Brij 58 and assayed, the binding protein exhibited a target size of 62,000 +/- 4,000 Da; in Triton X-100, the functional size of the receptor was 85,000 +/- 10,000 Da. Sedimentation equilibrium measurements of the purified binding protein yielded a lower limit molecular weight of 79,000 +/- 7,000. ...

1990-03-05

383

Evaluation of potential hydrocarbon sources in lacustrine facies of Newark Supergroup, eastern United States  

Energy Technology Data Exchange (ETDEWEB)

Lacustrine rocks are a significant component of many rift-valley sequences. Comparisons of both active and ancient rift valleys indicate that the lacustrine facies are commonly rich in organic matter and may be important sources for oil. For example, Holocene sediments in Lake Tanganyika and Cretaceous lacustrine rocks in west Africa contain as much as 12% and 20% TOC, respectively. The Newark Supergroup contains abundant lacustrine rocks. The widespread occurrence of black shales, the general similarity to known organically rich rift systems, and a few isolated geochemical analyses have caused some speculation about the potential of the Newark Supergroup to be an effective source of oil and gas. Sufficient geochemical analyses are available from lacustrine rocks in the Newark, Connecticut, and Deep River basins to evaluate their potential as hydrocarbon sources. In general, both the quantity and quality of organic matter in these rocks are less than that required ...

1985-02-01

384

Eocene sediment dispersal pattern records asymmetry of Laramide Green River basin, southwestern Wyoming  

Energy Technology Data Exchange (ETDEWEB)

Provenance and paleocurrent data from synorogenic fluvial sandstones can be used to constrain theories about the timing and structural style of Laramide foreland uplifts and associated basins. The Green River basin of southwestern Wyoming is a large ellipsoidal basin bounded by uplifts with diverse orientations and basement rock compositions. Sandstone from the main body of the Eocene Wasatch Formation in the Green River basin was sampled along the south and west flanks of the Rock Springs uplift. Petrographic examination and paleocurrent measurements reveal two main facies. The first facies is rich in feldspar and metamorphic rock fragments derived from the Wind River Mountains to the north. The second facies is dominated by quartz and sedimentary rock fragments, reflecting a source in the Uinta Mountains to the south. Distribution of these facies indicates that a sediment lobe extends 15 km into the basin from the Uinta Mountains. Another ...

1987-05-01

385

Contamination profiles of short-chain polychlorinated n-alkanes in foodstuff samples from Japan  

Energy Technology Data Exchange (ETDEWEB)

Polychlorinated n-alkanes (PCAs) are group of chemicals manufactured by chlorination of liquid n-paraffin or paraffin wax that contain 30 to 70% chlorine by weight. Large amounts of PCAs are widely used as plasticizers for vinyl chloride, lubricants, paints, and flame retardants and number of other industrial applications. Annual global production of PCAs is approximately 300 kilo tones, with a majority having medium-carbon-chain (C14-C19) length. According to the investigation made by Kagaku Kogyo Nippon-Sha, the annual consumption of PCAs in Japan was about 83,000 tons in between 1986-2001. Short-carbon-chain (C10-C13) has been placed on the Priority Substance List under Canadian Environmental Protection Act and on the Environmental Protection Agency Toxic Release Inventory in the USA due to its potential to act as tumor promoters in mammals. Data on environment levels of PCAs is meager, nevertheless, PCAs have been measured at relatively high concentrations in biota from Sweden, ...

2004-09-15

386

Buried soils of Late Quaternary moraines of the Wind River Mountains, Wyoming  

Energy Technology Data Exchange (ETDEWEB)

Buried soils occur on kettle floors of four Pinedale moraine catenas of the western Wind River Mountains of Wyoming. Radiocarbon ages from bulk samples of Ab horizons indicate the soils were buried during the mid-Holocene. Soils on kettle floors have silty A and Bw horizons that overlie buried A and B horizons that also formed in silt-rich sediments. Crests and backslope soils also have A and Bw horizons of sandy loam formed over 2BCb and 2Cb horizons of stony coarse loamy sand. Recent data show the silty textures of the A and B horizons are due to eolian silt and clay from the Green River Basin just west of the mountains. The buried soils appear to represent alternate periods of erosion and deposition on the moraines during the Holocene. The original soils developed on higher slopes of the moraines were eroded during the mid-Holocene and the 2BC and 2C horizons exposed at the surface. Eroded soil sediments were transported downslope onto the ...

1992-01-01

387

Aquatic pathways model to predict the fate of phenolic compounds  

Energy Technology Data Exchange (ETDEWEB)

Organic materials released from energy-related activities could affect human health and the environment. To better assess possible impacts, we developed a model to predict the fate of spills or discharges of pollutants into flowing or static bodies of fresh water. A computer code, Aquatic Pathways Model (APM), was written to implement the model. The computer programs use compartmental analysis to simulate aquatic ecosystems. The APM estimates the concentrations of chemicals in fish tissue, water and sediment, and is therefore useful for assessing exposure to humans through aquatic pathways. The APM will consider any aquatic pathway for which the user has transport data. Additionally, APM will estimate transport rates from physical and chemical properties of chemicals between several key compartments. The major pathways considered are biodegradation, fish and sediment uptake, photolysis, and evaporation. The model has been implemented with ...

1983-04-01

388

Validation of the CFD code fluent by post-test calculation of a density-driven ROCOM experiment  

Energy Technology Data Exchange (ETDEWEB)

During the last years, boron dilution events with the potential of reactivity transients were an important issue of German PWR safety analyses. A coolant with a low-boron concentration could be collected in localized areas of the reactor coolant system, e.g., by separation of a borated reactor coolant into highly concentrated and diluted fractions (inherent dilution) which can occur during reflux-condenser heat transfer after a small break loss of coolant accident with a limited availability of the emergency core cooling systems. During the course of follower core assessments, TUV NORD SysTec appraises safety analyses of boron dilution events presented by the utilities. These analyses are based on the simulation of boron dilution and transport processes in conjunction with a number of dedicated experiments. The analyses demonstrate that boron dilution events cannot lead to recriticality of the core. Hence, the boron ...

2007-09-15

389

Two-phase flow characteristic of inverted bubbly, slug and annular flow in post-critical heat flux region  

Energy Technology Data Exchange (ETDEWEB)

Inverted annular flow can be visualized as a liquid jet-like core surrounded by a vapor annulus. While many analytical and experimental studies of heat transfer in this regime have been performed, there is very little understanding of the basic hydrodynamics of the post-CHF flow field. However, a recent experimental study was done that was able to successfully investigate the effects of various steady-state inlet flow parameters on the post-CHF hydrodynamics of the film boiling of a single phase liquid jet. This study was carried out by means of a visual photographic analysis of an idealized single phase core inverted annular flow initial geometry (single phase liquid jet core surrounded by a coaxial annulus of gas). In order to extend this study, a subsequent flow visualization of an idealized two-phase core inverted annular flow geometry (two-phase central jet core, surrounded by ...

1988-01-01

390

Differential rod worth profile affected by axial blankets in FFTF [Fast Flux Test Facility  

International Nuclear Information System (INIS)

The central feature of the Fast Flux Test Facility (FFTF) is the fast test reactor (FTR), which is a liquid-sodium-cooled fast reactor providing high fast-neutron flux for irradiation testing of fuels and materials. The FTR also provides a means to develop breeder reactor core components and to gain reactor systems operating experience for future liquid-metal fast breeder reactors (LMFBRs). In the FTR core, there are 82 incore positions (within rows 1 through 6) available for driver fuel assemblies and/or test assemblies. In addition, there are three safety rods and six control rods located in rows 3 and 5, respectively, in the three symmetric core sectors. The FFTF has been successfully and continuously operated for more than 11 reactor cycles. For the first 8 cycles, the core loadings were composed of the mixed-oxide driver fuel assemblies and some test assemblies. These assemblies have an active ...

1990-06-10

391

Computational fluid dynamic analysis of core bypass flow phenomena in a prismatic VHTR  

International Nuclear Information System (INIS)

The core bypass flow in a prismatic very high temperature reactor (VHTR) is an important design consideration and can have considerable impact on the condition of reactor core internals including fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) are affected by bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to better understand bypass flow phenomena and establish an evaluation method for the reactor core ...

2010-09-01

392

Compatibility analysis of DUPIC fuel (part 3) - radiation physics analysis  

International Nuclear Information System (INIS)

As a part of the compatibility analysis of DUPIC fuel in CANDU reactors, the radiation physics calculations have been performed for the CANDU primary shielding system, thermal shield, radiation damage, transportation cask and storage. At first, the primary shield system was assessed for the DUPIC fuel core, which has shown that the dose rates and heat deposition rates through the primary shield of the DUPIC fuel core are not much different from those of natural uranium core because the power levels on the core periphery are similar for both cores. Secondly, the radiation effects on the critical components and the themal shields were assessed when the DUPIC fuel is loaded in CANDU reactors. Compared with the displacement per atom (DPA) of the critical component for natural uranium core, that for the DUPIC fuel core was increased by -30% for ...

2009-07-01

393

COLLAPSE AND FRAGMENTATION OF MOLECULAR CLOUD CORES. X. MAGNETIC BRAKING OF PROLATE AND OBLATE CORES  

International Nuclear Information System (INIS)

The collapse and fragmentation of initially prolate and oblate, magnetic molecular clouds is calculated in three dimensions with a gravitational, radiative hydrodynamics code. The code includes magnetic field effects in an approximate manner: magnetic pressure, tension, braking, and ambipolar diffusion are all modeled. The parameters varied for both the initially prolate and oblate clouds are the initial degree of central concentration of the radial density profile, the initial angular velocity, and the efficiency of magnetic braking (represented by a factor f _m_b = 10"-"4 or 10"-"3). The oblate cores all collapse to form rings that might be susceptible to fragmentation into multiple systems. The outcome of the collapse of the prolate cores depends strongly on the initial density profile. Prolate cores with central densities 20 times higher than their boundary densities collapse and fragment into binary or quadruple ...

2009-06-01

394

Variable elimination in chemical reaction networks with mass action kinetics  

CERN Document Server

We consider chemical reaction networks taken with mass action kinetics. The steady states of such a system are solutions to a system of polynomial equations. Even for small systems the task of finding the solutions is daunting. We develop an algebraic framework and procedure for linear elimination of variables. The procedure reduces the variables in the system to a set of "core" variables by eliminating variables corresponding to a set of non-interacting species. The steady states are parameterized algebraically by the core variables, and a graphical condition is given for when a steady state with positive core variables necessarily have all variables positive. Further, we characterize graphically the sets of eliminated variables that are constrained by a conservation law and show that this conservation law takes a specific form.

2011-01-01

395

Validation of a new software version for monitoring of the core of the Unit 2 of the Laguna Verde power plant with ARTS; Validacion de una nueva version del software para monitoreo del nucleo de la Unidad 2 de la Central Laguna Verde con ARTS  

Energy Technology Data Exchange (ETDEWEB)

In this work it is intended a methodology to validate a new version of the software used for monitoring the reactor core, which requires of the evaluation of the thermal limits settled down in the Operation Technical Specifications, for the Unit 2 of Laguna Verde with ARTS (improvements to the APRMs, Rod Block Monitor and Technical specifications). According to the proposed methodology, those are shown differences found in the thermal limits determined with the new versions and previous of the core monitoring software. Author)

2005-07-01

396

The role of natural circulation in the FFTF [Fast Flux Test Facility] passive safety tests  

International Nuclear Information System (INIS)

A series of tests were completed at the Fast Flux Test Facility to demonstrate the passive safety characteristics of liquid metal reactors with natural circulation flow. The first test consisted of transition from forced to natural circulation flow at an initial decay power of 0.3%. The second test represented an unprotected loss-of-flow transient to natural circulation from 50% power with the control rods prevented from scramming into the core. The third test was a steady-state, natural circulation condition with core fission powers up ato about 2.3%. Core sodium data and results of single and multi-channel computer models confirmed the reliability and effectiveness of natural circulation flow for liquid metal reactor safety.

1987-12-13

397

The hippo pathway in biological control and cancer development  

British Library Electronic Table of Contents (United Kingdom)

Abstract The Hippo pathway is an evolutionally conserved protein kinase cascade involved in regulating organ size in vivo and cell contact inhibition in vitro by governing cell proliferation and apoptosis. Deregulation of the Hippo pathway is linked to cancer development. Its first core kinase Warts was identified in Drosophila more than 15 years ago, but it gained much attention when other core components of the pathway were identified 8 years later. Major discoveries of the pathway were made during past several years. The core kinase components Hippo, Salvador, Warts, and Mats in the fly and Mst1/2, WW45, Lats1/2, and Mob1 in mammals phosphorylate and inactivate downstream transcriptional co-activators Yorkie in the fly, Yes-associated protein (YAP) and transcriptional co-activator with ...

2011-01-01

398

Synthesis and characterization of Co-Ag core-shell nanoparticles  

Energy Technology Data Exchange (ETDEWEB)

A micellar method has been used to prepare silver-coated cobalt (Co-Ag) nanoparticles. The synthesized particles have been deeply characterized by several methods, i.e., XRD, UV-Vis, TEM, XPS, and electrochemical techniques. There is every indication that the obtained particles show a truly core-shell structure. All the nanoparticles obtained under different conditions are in the size range 3-5 nm. High-resolution TEM (HRTEM), Fast Fourier Transformation (FFT), and Selected Area Electron Diffraction (SAED) indicated that the presence of hcp-Co and fcc-Ag, in which cobalt is located in the central area; meanwhile silver is at the edges of the nanoparticle. The absorption band of the Co-Ag colloid shifts to a longer wavelength and broadens relative to that of pure silver colloid. Voltammetric characterization allowed to determine the coverage of the cobalt core.

2010-08-15

399

Some sensitivities during a LWR severe core-damage sequence  

International Nuclear Information System (INIS)

Stable boiloff of core water during a severe LWR accident, that is, boiloff driven only by the decay power generated below the water level, is tractable analytically and is relatively insensitive to axial power distribution. As might be expected, calculated accident event times are sensitive to the fidelity of the decay power model. During later stages of boiloff, heat transfer or transport of energy from above the water level to the residual water can result in an unstable condition during which the boiloff rate increases greatly. The unstable boiloff phenomenon illustrates the highly nonlinear influence of core heat transfer during meltdown and emphasizes the great accuracy requirements which attend the modeling of the accident during periods of enhanced heat transfer when significant zirconium oxidation is possible.

1981-12-04

400

Self-inhibited rate in gas-solid noncatalytic reactions. The shrinking core model  

Energy Technology Data Exchange (ETDEWEB)

The shrinking core model is examined for gas-solid noncatalytic reactions with a self-inhibited rate form and it is shown that multiple reaction pathways are possible for solid particles reacted under identical conditions. The observed reaction rate can have up to two discontinuities (jumps) during reaction for particles of spherical and cylindrical shape. The geometric instability analysis reveals that the reaction interface is stable under a very limited set of conditions only for solid particles of slab geometry. For a sphere or cylinder at large Biot numbers the reaction interface is always potentially unstable. This model provides a plausible explanation for gas-solid reactions which exhibit erratic shrinking core behavior.

1984-02-01

401

Oak Ridge Research Reactor. Quarterly report, July, August, and September 1984  

Energy Technology Data Exchange (ETDEWEB)

The ORR operated at an average power level of 29.7 MW for 85.3% of the time during this period. The reactor was shut down on fifteen occasions, nine of which were unscheduled. Reactor downtime needed for refueling and checks was normal. The reactor remained available for operation 88.3% of the time. Special tests completed during the quarter included: (1) transfer of LEU fuel elements CLE-202 and NLE-201 from core positions B-9 and B-2 to core positions C-5 and C-6 for continued operation; and (2) calculation of maximum heat flux in LEU elements CLE-201 and NLE-202 in core positions A-2 and A-8. In-service inspections included inspections of ORR decay tank, primary heat exchanger No. 4, and the 24-in. strainer.

1985-03-01

402

Numerical and semi-analytic core mass distributions in supersonic isothermal turbulence  

CERN Document Server

We investigate the influence of the turbulence forcing on the mass distributions of gravitationally unstable cores by postprocessing data from simulations of non-selfgravitating isothermal supersonic turbulence with varying resolution. In one set of simulations solenoidal forcing is applied, while the second set uses purely compressive forcing to excite turbulent motions. From the resulting density field, we compute the mass distribution of gravitationally unstable cores by means of a clump-finding algorithm. Using the time-averaged probability density functions of the mass density, semi-analytic mass distributions are calculated from analytical theories. We apply stability criteria that are based on the Bonnor-Ebert mass resulting from the thermal pressure and from the sum of thermal and turbulent pressure. Although there are uncertainties in the application of the clump-finding algorithm, we find systematic differences in the mass ...

2010-01-01

403

Interpretation of gamma-scanning data from the ORR demonstration elements  

Energy Technology Data Exchange (ETDEWEB)

The HEU and LEU fuel elements used in the ORR whole-core demonstration were gamma-scanned to determine the axial distribution of the {sup 140}La and {sup 137}Cs activities. Analysis of this data is now complete. From the {sup 140}La activity distributions cycle-averaged powers were determined while the {sup 137}Cs data provided a measure of the final {sup 235}U burnup in the fuel elements. A method for calculating correction factors for activity gradients transverse to the fuel element axis is presented and is applied to the first mixed core used in the demonstration during the gradual transition to an all LEU core. Results based on the gamma-scanning of the LEU fuel followers are also presented. Improved burnup calculations against which the experimental results are to be compared are now in progress. 7 refs., 21 figs., 3 tabs.

1989-01-01

404

High Tc superconducting magnetic multivibrators for fluxgate magnetic-field sensors  

Science.gov (United States)

Sensitive and quick-response nonlinear inductance characteristics are found for high Tc superconducting (YBa/sub 2/Cu/sub 3/O/sub 7-chi/) disk cores at 77K in which soft magnetic BH hysteresis loops are observed. Various quick response magnetic devices such as modulators, amplifiers and sensors are built using these cores. The magnetizing frequency can be set to more than 20 MHz, which is difficult for conventional ferromagnetic bulk materials such as Permalloy amorphous alloys and ferrite. New quick-response fluxgate type magnetic-field sensors are made using ac and dc voltage sources. The former is used for second-harmonic type sensors, while the latter is for voltage-output multivibrator type sensors. Stable and quick-response sensor characteristics were obtained for two-core type multivibrators.

1989-09-01

405

Glueball Mass Spectrum in KK Monopole Background  

CERN Document Server

We consider typeIIA supergravity solution of D2-branes and D3-branes localized within D6-branes in the near-core region of D6-branes. With these solutions we can calculate the spectrum of the glueball mass in QCD3 and QCD4. The equation of motion describing the dilaton has the same eigenvalues and the same glueball masses in QCD3 and QCD4. Glueball mass spectrum is the same in the near core region of D6-branes of their M-theory counterpart is KK monopole. We conclude that the glueball mass spectrum is the same in QCD3 and QCD4 by considering the `near-core' limit of D6-branes of which M-theory counterpart (KK monopole background) becomes an ALE space with an $A_{N-1}$ singularity times 7 dimensional Minkowski space $M^{(6,1)}$.

1999-01-01

406

Fabrication, fabrication control and in-core follow up of 4 LEU leader fuel elements based on U{sub 3}Si{sub 2} in RECH-1  

Energy Technology Data Exchange (ETDEWEB)

The RECH-1 MTR reactor has been converted from HEU to MEU (45% enrichment) and the decision to a LEU (20% enrichment) conversion was taken some years ago. This LEU conversion decision involved a local fuel development and fabrication based on U{sub 3}Si{sub 2}-Al dispersion fuel, and a fabrication qualification stage that resulted in four fuel elements fully complying with established fabrication standards for this type of fuel. This report-presents relevant points of these four leaders fuel elements fabrication, in particular a fuel plate core homogeneity control development. A summary of the intended in core follow-up studies for the leaders fuel elements is also presented here. (author)

1999-07-01

407

Enhanced antibacterial activity of bifunctional Fe3O4-Ag core-shell nanostructures  

British Library Electronic Table of Contents (United Kingdom)

We describe a simple one-pot thermal decomposition method for the production of a stable colloidal suspension of narrowly dispersed superparamagnetic Fe3O4-Ag core-shell nanostructures. These biocompatible nanostructures are highly toxic to microorganisms. Antimicrobial activity studies were carried out on both Gram negative (Escherichia coli and Proteus vulgaris) and Gram positive (Bacillus megaterium and Staphylococcus aureus) bacterial strains. Efforts have been made to understand the underlying molecular mechanism of such antibacterial actions. The effect of the core-shell nanostructures on Gram negative strains was found to be better than that observed for silver nanoparticles. The minimum inhibitory concentration (MIC) values of these nanostructures were found to be considerably lowe...

2009-01-01

408

Digital mammography: more microcalcifications, more columnar cell lesions without atypia  

British Library Electronic Table of Contents (United Kingdom)

The incidence of columnar cell lesions in breast core needle biopsies since full-field digital mammography in comparison with screen-filmed mammography was analyzed. As tiny microcalcifications characterize columnar cell lesions at mammography, we hypothesized that more columnar cell lesions are diagnosed since full-field digital mammography due to its higher sensitivity for microcalcifications. In all, 3437 breast core needle biopsies performed in three hospitals and resulting from in total 55?159 mammographies were revised: 1424 taken in the screen-filmed mammography and 2013 in the full-field digital mammography period. Between the screen-filmed mammography and full-field digital mammography periods, we compared the proportion of mammographies that led to core needle biopsies, the...

2011-01-01

409

Development of Point Arguello field, offshore California  

Energy Technology Data Exchange (ETDEWEB)

Development drilling from Chevron-operated Platform Hermosa, located on OCS-P 0316 of the Point Arguello field, began on January 30, 1987. To date, seven development wells have been drilled in to the northwest-southeast-trending, doubly plunging anticlinal structure. The results from drilling have confirmed the presence of intense folding and fracturing in the targeted Monterey Formation. Over 700 ft of conventional core were recovered from the B-2 well in the lower Sisquoc and Monterey Formations. Analysis of the core material has yielded important information on lithologic variations and fracture patterns in the productive Monterey Formation. Initial results of core studies, DST data, and wireline studies indicate a correlation between rock type and fracturing. Fracture trends and directional permeability suggested by drill-stem testing may affect future drilling patterns in the field.

1988-03-01

410

Description of Cretaceous Sedimentary Sequence of the Yaojia Formation Recovered by CCSD-SK-Is Borehole in Songliao Basin: Lithostratigraphy, Sedimentary Facies and Cyclic Stratigraphy  

British Library Electronic Table of Contents (United Kingdom)

The Yaojia Formation recovered by CCSD-SK-Is borehole (China Cretaceous Continental Scientific Drilling-SongkeI-the south borehole) is 157.67 m long and 99.96% of cores recovery. The age of the formation corresponds with a range from the Santonian to the early Campanian. The sequences and processes of lithology-lithofacies and cyclic stratigraphy are revealed by a detailed core description. Eleven rock types and three kinds of sedimentary subfacies, including shallow lake, deep lake, and delta front, are recognized from the drilling core. There are eleven sedimentary microfacies including dolostone, argillaceous limestone, shallow lake turbidite, deep lake turbidite, subaqueous mouth bar, distal bar, sheet sandstone, subaqueous distributary bay, slump deposits, shallow lake mudstone, and d...

2009-01-01

411

Description of Cretaceous Sedimentary Sequence of the Quantou Formation Recovered by CCSD-SK-Is Borehole in Songliao Basin: Lithostratigraphy, Sedimentary Facies and Cyclic Stratigraphy  

British Library Electronic Table of Contents (United Kingdom)

The Quantou Formation recovered by CCSD-SK-Is borehole (China Cretaceous Continental Scientific Drilling-SongkeI-the south borehole) is 132.07 m long and the recovery of cores is 100%. The sequence and process of lithology-lithofacies and cyclostratigraphy are revealed by a detailed core description. Nine rock types and three kinds of sedimentary facies including meandering river, shallow lake, and delta front are recognized from the drilling core, there are ten sedimentary microfacies, which are point bar, natural levee, crevasse splay, crevasse channel, floodplain, flood lake, distributary mouth bar, interdistributary bay, mudstone of still water, and turbidite. The Quantou Formation represents seventy-six meter-scale cycles (sixth-order cycle), twenty-five fifth-order cycles, eight four...

2009-01-01

412

Dense and diffuse gas in dynamically active clouds  

CERN Document Server

We investigate the chemical and observational implications of repetitive transient dense core formation in molecular clouds. We allow a transient density fluctuation to form and disperse over a period of 1 Myr, tracing its chemical evolution. We then allow the same gas immediately to undergo further such formation and dispersion cycles. The chemistry of the dense gas in subsequent cycles is similar to that of the first, and a limit cycle is reached quickly (2 - 3 cycles). Enhancement of hydrocarbon abundances during a specific period of evolution is the strongest indicator of previous dynamical history. The molecular content of the diffuse background gas in the molecular cloud is expected to be strongly enhanced by the core formation and dispersion process. Such enhancement may remain for as long as 0.5 Myr. The frequency of repetitive core formation should strongly determine the level of background molecular enhancement. ...

2006-01-01

413

Core demonstration lead experiments for irradiation in FFTF  

International Nuclear Information System (INIS)

A major new initiative to develop and irradiate a long-life mixed oxide fuel system in the Fast Flux Test Facility (FFTF) has been implemented by the Westinghouse Hanford Company at the Hanford Engineering Development Lab. for the US Dept. of Energy. The purpose of this new fuel system, called the Core Demonstration Experiment (CDE), is to demonstrate the capability of achieving a 3-yr life in a prototypical heterogeneous reactor environment under prototypical power and temperature conditions. Three Core Demonstration Lead Experiments (CDLEs) will establish the performance characteristics of entire fuel assemblies of wire-wrapped, large diameter, advanced oxide fuel pins with HT-9 stainless steel alloy cladding and wire wrap and an HT-9 duct. Their performance characteristics provided the basis for design, fabrication, and irradiation of the CDE.

1987-06-07

414

Cancer-cell-specific cytotoxicity of non-oxidized iron elements in iron core-gold shell NPs  

British Library Electronic Table of Contents (United Kingdom)

Gold-coated iron nanoparticles (NPs) selectively and significantly (P <0.0001) inhibit proliferation of oral- and colorectal-cancer cells in vitro at doses as low as 5 mg/mL, but have little adverse effect on normal healthy control cells. The particle treatment caused delay in cell-cycle progression, especially in the S-phase. There was no significant difference in the NP uptake between cancer and control cells, and cytotoxicity resulted primarily from the iron core, before oxidation, rather than from the Fe ions released from the core. In contrast with magnetic NPs that usually serve as drug carriers, diagnostic probes or hyperthermia media, the iron, before oxidation, in the NPs selectively suppressed cancer cell growth and left healthy control cells unaffected in vitro and in vivo. This...

2011-01-01

415

Calculation of the X-ray emission spectra of VC and VN  

International Nuclear Information System (INIS)

From self-consistent band structure calculations using the 'augmented plane wave'(APW) method, the density of states can be decomposed into local partial (according to azimuthal quantum number l) components, the l-character densities. Within the APW formalism the intensity of X-ray emission spectra is determined by radial transition probabilities and l-character densities of such valence states, which reside inside the same atomic sphere as the core vacancy and whose quantum number l differs by +-1 from the one corresponding to the core state. By taking into account lifetime broadening of the core and valence states and also the instrumental broadening the computed spectra (non-metal K-, vanadium K- and Lsub(III)-spectra) agree well with experiment. (orig.).

416

Burnup analysis and in-core fuel management study of the 3MW TRIGA MARK II research reactor  

British Library Electronic Table of Contents (United Kingdom)

The principal objective of this study is to formulate an effective optimal fuel management strategy for the TRIGA MARK II research reactor at AERE, Savar. The core management study has been performed by utilizing four basic types of information calculated for the reactor: criticality, power peaking, neutron flux and burnup calculation. This paper presents the results of the burnup calculations for TRIGA LEU fuel elements. The fuel element burnup for approximately 20 years of operation was calculated using the TRIGAP compute code. The calculation is performed in one-dimensional radial geometry in TRIGAP. Inter-comparison of TRIGAP results with other two calculations performed by MVP-BURN and MCNP4C-ORIGEN2.1 show very good agreement. Reshuffling at 20,000MWh step provides the highest core l...

2008-01-01

417

Building connections - Transition from TN-C to TN-S five-core building connection cable solves problems; Hausanschluss: Wechsel von TN-C auf TN-S  

Energy Technology Data Exchange (ETDEWEB)

This article discusses the use of five-core cables to provide utility customers with the best possible prerequisites for trouble-free operation of electrical installations and equipment. The TN-S system in buildings and the new TN-S-five-core house-connection cable for connections between the mains distribution point and buildings is introduced. The long-term target of providing TN-S-systems in power distribution even as far as the local transformer is also discussed. The advantages of the system are discussed and various configurations for different types of supply are described.

2005-07-01

418

Analyses of eigenvalue bias and control rod worths in FFTF [Fast Flux Test Facility  

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.

1987-09-13

419

Analyses of eigenvalue bias and control rod worths in FFTF (Fast Flux Test Facility)  

Energy Technology Data Exchange (ETDEWEB)

The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.

1987-01-01

420

An americium-fueled gas core nuclear rocket  

Energy Technology Data Exchange (ETDEWEB)

A gas core fission reactor that utilizes americium in place of uranium is examined for potential utilization as a nuclear rocket for space propulsion. The isomer [sup 242m]Am with a half life of 141 years is obtained from an (n, [gamma]) capture reaction with [sup 241]Am, and has the highest known thermal fission cross section. We consider a 7500 MW reactor, whose propulsion characteristics with [sup 235]U have already been established, and re-examine it using americium. We find that the same performance can be achieved at a comparable fuel density, and a radial size reduction (of both core and moderator/reflector) of about 70%.

1993-01-10

421

A novel electrogenerated chemiluminescence sensor for pyrogallol with core-shell luminol-doped silica nanoparticles modified electrode by the self-assembled technique  

British Library Electronic Table of Contents (United Kingdom)

The core-shell luminol-doped SiO2 nanoparticles were synthesized and immobilized on the surface of chitosan film coating graphite electrode by the self-assembled technique. Then, a novel electrogenerated chemiluminescence (ECL) sensor for pyrogallol was developed based on its ECL enhancing effect for the core-shell luminol-doped silica nanoparticles. The ECL analytical performances and the sensing mechanism of this ECL sensor for pyrogallol were investigated in detail. The corresponding results showed that: compared with the conventional ECL reaction procedures by luminol ECL reaction system, the electrochemical (EC) reaction of pyrogallol and its subsequent chemiluminescence (CL) reaction occurred in the different spatial region whilst offering a high efficiency to couple the EC with the ...

2006-01-01

422

caCORE version 3: Implementation of a model driven, service-oriented architecture for semantic interoperability.  

Science.gov (United States)

One of the requirements for a federated information system is interoperability, the ability of one computer system to access and use the resources of another system. This feature is particularly important in biomedical research systems, which need to coordinate a variety of disparate types of data. In order to meet this need, the National Cancer Institute Center for Bioinformatics (NCICB) has created the cancer Common Ontologic Representation Environment (caCORE), an interoperability infrastructure based on Model Driven Architecture. The caCORE infrastructure provides a mechanism to create interoperable biomedical information systems. Systems built using the caCORE paradigm address both aspects of interoperability: the ability to access data (syntactic interoperability) and understand the data once retrieved (semantic interoperability). This infrastructure consists of an integrated set of three major components: a ...

2007-04-02

423

caCORE version 3: Implementation of a model driven, service-oriented architecture for semantic interoperability  

UK PubMed Central (United Kingdom)

One of the requirements for a federated information system is interoperability, the ability of one computer system to access and use the resources of another system. This feature is particularly...Full Text Available

2008-02-01

424

Upper reactor core supporting structure of highly earthquake-proof type  

International Nuclear Information System (INIS)

Fuel assemblies in a reactor pressure vessel are disposed in a reactor core shroud. The own weight of the fuel assembly is supported by a reactor core support plate, and is supported, for the horizontal direction, by an upper lattice plate and the reactor core support plate. A support portion for the upper portion of the fuel assembly is disposed above the fuel assembly, and a support portion for the support portion described above is joined to a shroud head by welding. The support portion for the upper portion of the fuel assembly has a network-like portion which absorbs and disperses rising force which exerted on the fuel assembly when the fuel assembly is risen by seismic forces. The rising force exerted on the fuel assembly absorbed by the network-like portion is effectively transferred to the shroud head by the support portion. With such a constitution, rising of the fuel assembly can be prevented against the seismic ...

1993-05-14

425

Thermosensitive TRP channel pore turret is part of the temperature activation pathway  

UK PubMed Central (United Kingdom)

Temperature sensing is crucial for homeotherms, including human beings, to maintain a stable body core temperature and respond to the ambient environment. A group of exquisitely temperature-sensitive...Full Text Available

2010-04-13

426

The QseC Adrenergic Signaling Cascade in Enterohemorrhagic E. coli (EHEC)  

UK PubMed Central (United Kingdom)

The ability to respond to stress is at the core of an organism's survival. The hormones epinephrine and norepinephrine play a central role in stress responses in mammals, which require the synchronized...Full Text Available

2009-08-01

427

Teaching safe and effective prescribing in UK medical schools: a core curriculum for tomorrow's doctors  

UK PubMed Central (United Kingdom)

There is a pressing need for medical graduates to be fully prepared to take on the responsibilities of prescribing and to be able to respond to continual inevitable rapid changes in therapeutics. The...Full Text Available

2003-06-01

428

Taking the plunge: integrating structural, enzymatic and computational insights into a unified model for membrane-immersed rhomboid proteolysis  

UK PubMed Central (United Kingdom)

SYNOPSISRhomboid proteases are a fascinating class of enzymes that combine a serine protease active site within the core of an integral membrane protein. Despite having key roles...Full Text Available

429

Synthesis and characterization of PVP-coated large core iron oxide nanoparticles as an MRI contrast agent  

UK PubMed Central (United Kingdom)

The purpose of this study was to synthesize biocompatible polyvinylpyrrolidone (PVP)-coated iron oxide (PVP-IO) nanoparticles and to evaluate their efficacy as a magnetic resonance imaging (MRI)...Full Text Available

2008-04-01

430

Structure of plant nuclear and ribosomal DNA containing chromatin.  

UK PubMed Central (United Kingdom)

Digestion of plant chromatin from Brassica pekinensis and Matthiola incana with staphylococcus nuclease leads to a DNA repeat of 175 plus or minus 8 and a core size of 140 base pairs. DNase I digestion...Full Text Available

1979-11-10

431

Seasonal proteomic changes reveal molecular adaptations to preserve and replenish liver proteins during ground squirrel hibernation  

UK PubMed Central (United Kingdom)

Hibernators are unique among mammals in their ability to survive extended periods of time with core body temperatures near freezing and with dramatically reduced heart, respiratory, and metabolic rates...Full Text Available

2010-02-01

432

Seasonal Protein Changes Support Rapid Energy Production in Hibernator Brainstem  

UK PubMed Central (United Kingdom)

During the torpor phase of mammalian hibernation when core body temperature is near 4°C, the autonomic system continues to maintain respiration, blood pressure and heartbeat despite...Full Text Available

2010-04-01

433

Scale-model characterization of flow-induced vibrational response of FFTF reactor internals  

Energy Technology Data Exchange (ETDEWEB)

Fast Test Reactor core internal and peripheral components were assessed for flow-induced vibrational characteristics under scaled and simulated prototype flow conditions in the Hydraulic Core Mockup as an integral part of the Fast Test Reactor Vibration Program. The Hydraulic Core Mockup was an 0.285 geometric scale model of the Fast Test Reactor internals designed to simulate prototype vibrational and hydraulic characteristics. Using water to simulate sodium coolant, vibrational characteristics were measured and determined for selected model components over the scaled flow range of 36 to 110%. Additionally, in-situ shaker tests were conducted on selected Hydraulic Core Mockup outlet plenum components to establish modal characteristics. Most components exhibited resonant response at all test flow rates; however, the measured dynamic response was neither abnormal nor anomalously flow-rate dependent, and ...

1980-10-01

434

Regulation of apoptosis by the circadian clock through NF-?B signaling  

UK PubMed Central (United Kingdom)

In mice and humans the circadian rhythm of many biochemical reactions, physiology, and behavior is generated by a transcriptional-translation feedback loop (TTFL) made up of the so-called core clock...Full Text Available

2011-07-19

435

Plasma Electric Potential Evolution at the Core and Edge of the TJ-II Stellarator and T-10 Tokamak  

International Nuclear Information System (INIS)

In this article are presented main results on electric potential investigations in stellarator/torsatron TJ-II and tokamak T-10 in a comparable regimes of device operation.

2006-01-01

436

Percutaneous core excision and radiofrequency thermo-coagulation for the ablation of osteoid osteoma of the spine  

UK PubMed Central (United Kingdom)

Percutaneous radiofrequency ablation is the treatment of choice for osteoid osteoma of the appendicular skeleton. However, difficulties in localizing the lesion in the spine and its proximity to neural...Full Text Available

2009-03-01

437

Name techniques in Canada: current trends in utilization rates and recommendations for their inclusion at the Canadian Memorial Chiropractic College  

UK PubMed Central (United Kingdom)

Since its establishment in 1945, the Canadian Memorial Chiropractic College (CMCC) has predominately adhered to a Diversified model of chiropractic technique in the core curriculum; however, many students...Full Text Available

2000-09-01

438

NAME=\\  

Wastenet

...this pathway study the following two focus modules (in addition to the six core modules) and carry out a research investigation within this theme: Agricultural Production Systems Considers the type of farming systems that have evolved globally in relation to the prevailing agro-climatic zones, the influences of economic factors ...

439

Monte-Carlo-based simulation of LWR cores with innovative fuel concepts  

International Nuclear Information System (INIS)

High resolution Monte-Carlo simulations show that the neutron spectrum, fuel burnup and fuel temperature feedback effect of a PWR core loaded with Thoria-based fuel (Th/Pu-O_2) do not significantly differ from the MOX fuelled one due to the similar neutronic characteristics of both fertile materials (Th-232, U-238). The core physics of this fuel variant is characterized by an enhanced moderator/void temperature coefficient (by factor 2.4) and high incineration rate for Pu (approx. 60 %). A PWR core loaded with the Molybdenum-based inert matrix fuel (IMF) - in contrast to MOX-, shows a harder spectrum, resulting in small temperature coefficients of reactivity and particularly in a higher fuel depletion rate as well as an enhanced TRU reduction performance. The incineration of Pu amounts to 46 % resulting, in turn, in generation of minor actinides of about 10 % of the total Pu consumption. The higher excess reactivity ...

2009-05-03

440

Methods and findings of the SNR study  

International Nuclear Information System (INIS)

A featfinding committee of the German Federal Parliament in July 1980 recommended to perform a ''risk-oriented study'' of the SNR-300, the German 300 MW fast breeder prototype reactor being under construction in Kalkar. The main aim of this study was to allow a comparative safety evaluation between the SNR-300 and a modern PWR, thus to prepare a basis for a political decision on the SNR-300. Methods and main results of the study are presented in this paper. In the first step of the risk analysis six groups of accidents have been identified which may initiate core destruction. These groups comprise all conceivable courses, potentially leading to core destruction. By reliability analyses, expected frequency of each group has been calculated. In the accident analysis potential failure modes of the reactor tank have been investigated. Core destruction may be accompanied by the release of significant amounts of mechanical ...

441

Mapping Drug Physico-Chemical Features to Pathway Activity Reveals Molecular Networks Linked to Toxicity Outcome  

UK PubMed Central (United Kingdom)

The identification of predictive biomarkers is at the core of modern toxicology. So far, a number of approaches have been proposed. These rely on statistical inference of toxicity response from either...Full Text Available

442

Mammalian end binding proteins control persistent microtubule growth  

UK PubMed Central (United Kingdom)

End binding proteins (EBs) are highly conserved core components of microtubule plus-end tracking protein networks. Here we investigated the roles of the three mammalian EBs in controlling microtubule...Full Text Available

2009-03-09

443

Journey Into Cyberspace (6-Part Video Series) - NASA CORE ...  

Science.gov (United States)

Nov 30, 2010 ... Journey Into Cyberspace (6-Part Video Series). Length/Year. 146 minutes/1993. Media. VHS. Item Number. 004.0-11V ...

444

Forming Standing Joint Special Operations Task Force Headquarters.  

Science.gov (United States)

Special Operations Forces (SOF) within a Joint Task Force are controlled by a Joint Special Operations Task Force (JSOTF). Presently, JSOTF headquarters are formed around the core of the Theater Special Operations Command (TSOC), a service SOF headquarter...

2003-01-01

445

FDTD analysis of body-core temperature elevation in children and adults for whole-body exposure  

Energy Technology Data Exchange (ETDEWEB)

The temperature elevations in anatomically based human phantoms of an adult and a 3-year-old child were calculated for radio-frequency whole-body exposure. Thermoregulation in children, however, has not yet been clarified. In the present study, we developed a computational thermal model of a child that is reasonable for simulating body-core temperature elevation. Comparison of measured and simulated temperatures revealed thermoregulation in children to be similar to that of adults. Based on this finding, we calculated the body-core temperature elevation in a 3-year-old child and an adult for plane-wave exposure at the basic restriction in the international guidelines. The body-core temperature elevation in the 3-year-old child phantom was 0.03 deg. C at a whole-body-averaged specific absorption rate of 0.08 W kg{sup -1}, which was 35% smaller than in the adult female. This difference is attributed to the child's ...

2008-09-21

446

Evolution of Thermal Response Properties in a Cold-Activated TRP Channel  

UK PubMed Central (United Kingdom)

Animals sense changes in ambient temperature irrespective of whether core body temperature is internally maintained (homeotherms) or subject to environmental variation (poikilotherms). Here we show...Full Text Available

447

Equation of state of laser-shocked compressed iron; Equation d'etat du fer comprime par choc laser  

Energy Technology Data Exchange (ETDEWEB)

This thesis enters the field of highly compressed materials equation of state studies. In particular, it focuses on the case of laser shock compressed iron. This work indeed aims at getting to the conditions of the earth's core, comprising a solid inner core and a liquid outer core. The understanding of phenomena governing the core's thermodynamics and the geodynamic process requires the knowledge of iron melting line locus around the solid-liquid interface at 3.3 Mbar. Several experiments were performed to that extent. First, an absolute measurement of iron Hugoniot was obtained. Following is a study of partially released states of iron into a window material: lithium fluoride (LiF). This configuration enables direct access to compressed iron optical properties such as reflectivity and self-emission. Interface velocity measurement is dominated by compressed LiF optical properties and ...

2004-01-01

448

Engineering Task Plan for Water Supply for RMCS Spray Wash Trailer  

Energy Technology Data Exchange (ETDEWEB)

This ETP defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS)Spray Wash Trailer.

2000-04-20

449

Emergency core cooling device  

International Nuclear Information System (INIS)

In an existent emergency reactor core cooling device, if a ruptures should occure in a pipeline of a gravitational dropping type reactor core cooling system pool (GDCS) due to some or other causes, a portion of GDCS pool water was flown out of the ruptured port and could not be used for reactor core cooling. Then, a difference pressure detector is disposed to a GDCS pipeline at the inlet of a reactor pressure vessel. When it is judged by the detector, that coolants flow to the outside of the injection pipeline, an injection value disposed to the GDCS pipeline is closed by the difference pressure signal. Even if a rupture should occur on the side of the pressure vessel at downstream to the check value of the GDCS pipeline, since backflow is caused at the pressure container inlet of the GDCS pipeline with the rupture port, the rupture is detected by the difference pressure detector to close the injection valve. Therefore, ...

1990-10-29

450

Do the Obese Have Lower Body Temperatures? A New Look at a Forgotten Variable in Energy Balance  

UK PubMed Central (United Kingdom)

Understanding the pathogenesis of obesity is now more important than ever, given the remarkable world-wide epidemic. This paper explores the potential role of core temperature in energy balance, and...Full Text Available

2009-01-01

451

Development on the core technologies for tritium removal processes (I).  

Science.gov (United States)

At Wolsung NPP, three more CANDU reactors will be operated soon, and the tritium accumulation in the moderator and coolant systems was estimated to be greatly increased. In order to reduce tritium exposure for nuclear safety at Wolsung, a study was carrie...

1993-01-01

452

Deficiency of circadian protein CLOCK reduces lifespan and increases age-related cataract development in mice  

UK PubMed Central (United Kingdom)

Circadian clock is implicated in the regulation of aging. The transcription factor CLOCK, a core component of the circadian system, operates in complex with another circadian clock protein BMAL1. Recently...Full Text Available

453

Core technologies for Tritium removal processes (I).  

Science.gov (United States)

In case of operating both Wolsung Nuclear Units 1 and 2 without operating tritium removal facilities, it is estimated that tritium in 2013 would be accumulated up to about 30 million Ci that would result in about 2,300 man-rem of tritium exposure to opera...

1992-01-01

454

Core reactor calculation using the adaptive remeshing with a current error estimator  

International Nuclear Information System (INIS)

With the objective to improve the reactor physics calculation on a 2D and 3D nuclear reactor via the Diffusion Equation, an adaptive automatic finite element remeshing method, based on the elementary area (2D) or volume (3D) constraints, has been developed. The adaptive remeshing technique, guided by a posteriori error estimator, makes use of two external mesh generator programs: Triangle and TetGen. The use of these free external finite element mesh generators and an adaptive remeshing technique based on the current field continuity show that they are powerful tools to improve the neutron flux distribution calculation and by consequence the power solution of the reactor core even though they have a minor influence on the critical coefficient of the calculated reactor core examples. Two numerical examples are presented: the 2D IAEA reactor core numerical benchmark and the 3D model of the Argonauta research reactor, built in ...

455

Core Synthesis Facility: Bridging the Gap between Chemistry and Biology  

UK PubMed Central (United Kingdom)

CF-23“The biggest stumbling block for biological sciences turned out to be synthetic organic chemistry” – Elias A. Zerhouni, Former NIH Director in Chemical...Full Text Available

2010-09-01

456

Concentrating Engines and the Kidney  

UK PubMed Central (United Kingdom)

Mass balance relations, valid for any counterflow system, are derived and applied to a central core model of the renal medulla, in which descending Henle's limbs (DHL), ascending Henle's limbs (AHL),...Full Text Available

1973-06-01

457

Coaxial nanocables of p-type zinc telluride nanowires sheathed with silicon oxide: synthesis, characterization and properties  

International Nuclear Information System (INIS)

Coaxial nanocables with a single-crystalline zinc telluride (ZnTe) nanowire core and an amorphous silicon oxide (SiO_x) shell have been synthesized via a simple one-step chemical vapor deposition (CVD) method on gold-decorated silicon substrates. The single-crystal ZnTe nanowire core is in zinc-blende structure along the [111] direction, while the uniform SiO_x shell fully covers the core with no observable pin-hole or crack. Formation mechanisms of the ZnTe-SiO_x nanocables are discussed. The ZnTe nanowire core shows p-type electrical properties while the SiO_x shell acts as an effective insulating layer. The ZnTe-SiO_x nanocables may have potential applications in nanoscale devices, such as p-type FETs and nanosensors.

2009-11-11

458

Chandra Observations of Nuclear X-ray Emission from a Sample of Radio Sources  

CERN Document Server

We present the X-ray properties of a sample of 17 radio sources observed with the Chandra X-ray Observatory as part of a project aimed at studying the X-ray emission from their radio jets. In this paper, we concentrate on the X-ray properties of the unresolved cores. The sample includes 16 quasars (11 core-dominated and 5 lobe-dominated) in the redshift range z=0.30--1.96, and one low-power radio-galaxy at z=0.064. No diffuse X-ray emission is present around the cores of the quasars, except for the nearby low-power galaxy that has diffuse emission on a scale and with a luminosity consistent with other FRIs. No high-amplitude, short-term variability is detected within the relatively short Chandra exposures. However, 1510-089 shows low-amplitude flux changes with a timescale of $\\sim$25 minutes. The X-ray spectra of the quasar cores are generally well described by a single power law model with Galactic ...

2003-01-01

459

Assessment of 1183 screen-detected, category 3B, circumscribed masses by cytology and core biopsy with long-term follow up data  

UK PubMed Central (United Kingdom)

Discrete masses are commonly detected during mammographic screening and most such lesions are benign. For lesions without pathognomonically benign imaging features that are still regarded likely to...Full Text Available

2008-04-08

460

Are Petals Sterile Stamens or Bracts? The Origin and Evolution of Petals in the Core Eudicots  

UK PubMed Central (United Kingdom)

BackgroundThe aim of this paper is to discuss the controversial origins of petals from tepals or stamens and the links between the morphological expression of petals and floral organ...Full Text Available

2007-09-01

461

Anti-cancer drug loaded iron-gold core-shell nanoparticles (Fe@Au) for magnetic drug targeting.  

Science.gov (United States)

Magnetic drug targeting, using core-shell magnetic carrier particles loaded with anti-cancer drugs, is an emerging and significant method of cancer treatment. Gold shell-iron core nanoparticles (Fe@Au) were synthesized by the reverse micelle method with aqueous reactants, surfactant, co-surfactant and oil phase. XRD, XPS, TEM and magnetic property measurements were utilized to characterize these core-shell nanoparticles. Magnetic measurements showed that the particles were superparamagnetic at room temperature and that the saturation magnetization decreased with increasing gold concentration. The anti-cancer drug doxorubicin (DOX) was loaded onto these Fe@Au nanoparticle carriers and the drug release profiles showed that upto 25% of adsorbed drug was released in 80 h. It was found that the amine (-NH2) group of DOX binds to the gold shell. An in vitro apparatus simulating the human circulatory system was used to determine ...

2010-09-01

462

Altered Brain Activation in Ventral Frontal-Striatal Regions Following a 16-week Pharmacotherapy in Unmedicated Obsessive-Compulsive Disorder  

UK PubMed Central (United Kingdom)

Recent studies have reported that cognitive inflexibility associated with impairments in a frontal-striatal circuit and parietal region is a core cognitive deficit of obsessive-compulsive disorder (OCD)....Full Text Available

2011-05-01

463

Allosteric Drug Discrimination Is Coupled to Mechanochemical Changes in the Kinesin-5 Motor Core*  

UK PubMed Central (United Kingdom)

Essential in mitosis, the human Kinesin-5 protein is a target for >80 classes of allosteric compounds that bind to a surface-exposed site formed by the L5 loop. Not established is why there...Full Text Available

2010-06-11

464

Abrupt climate change and collapse of deep-sea ecosystems  

UK PubMed Central (United Kingdom)

We investigated the deep-sea fossil record of benthic ostracodes during periods of rapid climate and oceanographic change over the past 20,000 years in a core from intermediate depth in the northwestern...Full Text Available

2008-02-05

465

ADIABATIC MASS LOSS AND THE OUTCOME OF THE COMMON ENVELOPE PHASE OF BINARY EVOLUTION  

International Nuclear Information System (INIS)

We have developed a new method for calculating common envelope (CE) events based on explicit consideration of the donor star's structural response to adiabatic mass loss. In contrast to existing CE prescriptions, which specify a priori the donor's remnant mass, we determine this quantity self-consistently and find that it depends on binary and CE parameters. This aspect of our model is particularly important to realistic modeling for upper main-sequence star donors without strongly degenerate cores (and hence without a clear core/envelope boundary). We illustrate the central features of our method by considering CE events involving 10 M_s_u_n donors on or before their red giant branch. For such donors, the remnant core mass can be as much as 30% larger than the star's He-core mass. Applied across a population of such binaries, our methodology results in a significantly broader remnant mass and final ...

2010-08-10

466

A new method to measure necrotic core and calcium content in coronary plaques using intravascular ultrasound radiofrequency-based analysis  

UK PubMed Central (United Kingdom)

Although previous intravascular ultrasound (IVUS) radiofrequency-based analysis data showed acceptable reproducibility for plaque composition, measurements are not easily obtained, particularly that...Full Text Available

2010-04-01

467

The Preliminary GAMMA Code Thermal hydraulic Analysis for the Steady State of HTR-10 Initial Core  

Energy Technology Data Exchange (ETDEWEB)

This report describes the preliminary thermalhydraulic analysis of HTR-10 steady state full power initial core to provide a benchmark calculation of VHTGR(Very High-Temperature Gas-Cooled Reactors) safety analysis code of GAMMA(GAs Multicomponent Mixture Analysis). The input data of GAMMA code are produced for the models of fluid block, wall block, radiation heat transfer and each component material properties in HTR-10 reactor. The temperature and flow distributions of HTR-10 steady state 10 MW{sub th} full power initial core are calculated by GAMMA code with boundary conditions of total reactor inlet flow rate of 4.32 kg/s, inlet temperature of 250 .deg. C, inlet pressure of 3 MPa, outlet pressure of 2.992 MPa and the fixed temperature at RCCS water cooling tube of 50 .deg C. The calculation results are compared with the measured solid material temperatures at 22 fixed instrumentation positions in HTR-10. The wall temperature distribution in ...

2006-07-15

468

Proceedings of the first analysis meeting on JUPITER-II Program  

Energy Technology Data Exchange (ETDEWEB)

The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.

1984-12-31

469

Priority rankings of the system modifications to reduce core damage frequency of Wolsong NPP units 2/3/4  

International Nuclear Information System (INIS)

The analysis for priority rankings of the recommendations to reduce the total core damage frequency (CDF) of Wolsong nuclear power plant units 2/3/4 was performed in this paper. In order to derive the recommendations, the sensitivity analysis of CDF on which major contributors effect was performed based on the accident quantification results during Level 1 probabilistic safety assessments (PSA). Priorities were ranked in the way that compares the CDF reduction rate with the efforts required to implement those recommendations using risk matrix.

1998-05-01

470

Overview of US LMFBR Structural Materials Mechanical Properties Program  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the objective, scope, and status of the US Department of Energy's Materials and Structures Program to develop a data base on mechanical properties of structural materials for out-of-core structures and components for LMFBRs. Information on the development of a reference data base on materials for the reactor system, reactor enclosure system, primary heat transport system, intermediate heat transport system, and steam generator system is included. In addition, the development of the data and analyses to account for the effects of temperature and stress, as well as water/steam, sodium, and radiation environments, is described. Plans for the development of alternative materials for future out-of-core applications are presented.

1983-01-01

471

Overview of U.S. LMFBR structural materials mechanical properties program  

International Nuclear Information System (INIS)

This paper presents the objective, scope, and status of the U.S. Department of Energy's Materials and Structures Program to develop a data base on mechanical properties of structural materials for out-of-core structures and components for LMFBRs. Information on the development of a reference data base on materials for the reactor system, reactor enclosure system, primary heat transport system, intermediate heat transport system, and steam generator system is included. In addition, the development of the data and analyses to account for the effects of temperature and stress, as well as water/steam, sodium, and radiation environments, is described. Plans for the development of alternative materials for future out-of-core applications are presented. (author).

1983-10-10

472

Origin of binary stars  

Energy Technology Data Exchange (ETDEWEB)

Results of analytical study of early stages of a single star evolution are used investigation of the rotational fragmentation of the collapsing gas-dust cloud which leads to formation of two types of binaries. Wide ..cap alpha..-systems (Psub(orb) > or approximately 100 yrs) with usually unequal masses of components are formed before the formation of gas-dust core in hydrostatical equilibrium. Close ..beta..-systems (Psub(orb) < or approximation 100 yrs) with usually nearly equal masses of components are formed in the course of the collapse of gas-dust core.

1983-03-01

473

Nuclear design analysis of wolsung-1 CANDU-PHW nuclear generating station  

International Nuclear Information System (INIS)

A combination of computer codes such as LATREP, HWRAXAV and CITATION is utilized in an attempt to analyze the nuclear design characteristics of the CAXDU-PHWR of the Wolsung Unit 1. The major nuclear properties to be computed are the lattice properties of CANDU fuel channel and the core channel power distribution. The computed results are compared with the preliminary safety reports documentation for the Wolsung reactor. The observed discrepancies between our computations and the preliminary safety reports values are discussed in terms of incomplete information on the description of the core configuration in the preliminary safety reports and the different calculation methods. (author).

1978-01-01

474

Magnetic fluctuation measurement in Sino United Spherical Tokamak plasma  

International Nuclear Information System (INIS)

To investigate the magnetic fluctuations and for further transport study, the poloidal and radial magnetic field measurement is conducted on the Sino United Spherical Tokamak (SUNIST). Auto-power spectral density indicates that the magnetic fluctuation energy mainly concentrates in the frequency region lower than 10 kHz. The magnetic field oscillations, which are characterized by harmonic frequencies of 40 kHz, are observed in the scrape-off layer; by contrast, in the plasma core, the magnetic fluctuations are of Gaussian type. The time-frequency profiles show that the poloidal magnetic fluctuations are temporally intermittent. The autocorrelation calculation indicates that the fluctuations in decorrelation time vary between the core and the edge. (authors)

2007-07-01

475

Is spent nuclear fuel at the Kola coast a real danger?  

Energy Technology Data Exchange (ETDEWEB)

Norwegian authorities regard with some disquiet the possibility of a criticality accident in a ship propulsion reactor core at the Kola coast. Along this coast, in land storages, floating storages and in submarines taken out of service, the total number of spent fuel reactor cores amount to two hundred. The total Cs-137 radioactivity in spent ship propulsion reactor fuel at the Kola peninsula can be assessed to 600,000 TBq. A worst case release may amount to more than 5,000 TBq Cs-137, a quantity which under unfavourable conditions might cause serious contamination locally and even across the border to Norway.

1995-12-31

476

Implementation and management of Daya Bay Nuclear Power Plant in-core flux thimble tube in-service inspection  

International Nuclear Information System (INIS)

This article discusses the Daya Bay nuclear power plant in-core flux thimble tube in-service inspection method and strategy. High light of the multiple frequency eddy current technology adopted including frequency and probe choice, standard design, data acquisition process are involved. The wear defect-growing trends are studied on base of the history data, which contribute to the in-service inspection strategy decision. (authors)

2003-04-08

477

Gold and gold-silver core-shell nanoparticle constructs with defined size based on DNA hybridization  

Energy Technology Data Exchange (ETDEWEB)

Nanoparticles represent versatile building blocks in material science and nanotechnology. Thereby, the defined assembly of nanostructures (13 and 56 nm in diameter, respectively) is of significant importance. Short DNA sequences can be bound to the nanoparticle surface thus enabling highly specific DNA hybridization-driven events that direct the formation of nanoparticle constructs.In this paper, examples for the defined formation of gold nanoparticle constructs are demonstrated. In addition, gold-silver core-shell nanoparticles are introduced as further building blocks for the hybridization-controlled formation of nanoparticle constructs.

2009-04-15

478

Fission-track study of the uranium bio-geochemistry in carbonates of Bikini and Enewetak Atolls. Progress report, July 1, 1974--December 31, 1975  

International Nuclear Information System (INIS)

Major contributions during this contract period have been in developing an analytical procedure for Pu measurement, and in applying the developed procedures to determining the plutonium concentration and distribution in coral from the Bikini Atoll. In conjunction with these contributions, measurements using the fission-track method have been made of the uranium distribution and concentrations in several carbonate samples from drill cores obtained from the Runit Island Enewetak Atoll. Petrographic studies on these drill core samples have been made to correlate the uranium data with the mineralogical data.

479

Fission-track study of the uranium bio-geochemistry in carbonates of Bikini and Enewetak Atolls. Progress report, July 1, 1974--December 31, 1975  

Science.gov (United States)

Major contributions during this contract period have been in developing an analytical procedure for Pu measurement, and in applying the developed procedures to determining the plutonium concentration and distribution in coral from the Bikini Atoll. In conjunction with these contributions, measurements using the fission-track method have been made of the uranium distribution and concentrations in several carbonate samples from drill cores obtained from the Runit Island Enewetak Atoll. Petrographic studies on these drill core samples have been made to correlate the uranium data with the mineralogical data. (auth)

1975-09-01

480

FFTF core and primary sodium circuit instrumentation  

International Nuclear Information System (INIS)

Plans, engineering parameters, and some test results for several FFTF core and primary sodium circuit instrument systems are presented. The systems discussed include temperature, flow, pressure, leak detectors, level sensors, fuel failure monitoring, sodium impurity analysis and cover gas monitors. Since many of these instruments are similar to those used in other fast reactors around the world, only a brief description is presented for these systems. Results of recent demonstration tests of the FFTF Under-Sodium Viewing and Ranging system are also presented. (U.K.).

481

DISSIPATION AND EXTRA LIGHT IN GALACTIC NUCLEI. III. 'CORE' ELLIPTICALS AND 'MISSING' LIGHT  

International Nuclear Information System (INIS)

We investigate how 'extra' or 'excess' central light in the surface brightness profiles of cusp or power-law elliptical galaxies relates to the profiles of ellipticals with cores. The envelopes of cusp ellipticals are established by violent relaxation in mergers acting on stars present in gas-rich progenitor disks, while their centers are structured by the relics of dissipational, compact starbursts. Ellipticals with cores are formed by the subsequent merging of the now gas-poor cusp ellipticals, with the fossil starburst components combining to preserve a dense, compact component in these galaxies as well (although mixing of stars smooths the transition from the outer to inner components in the profiles). By comparing extensive hydrodynamical simulations to observed profiles spanning a broad mass range, we show how to observationally isolate and characterize the relic starburst component in core ellipticals. Our method ...

2009-04-01

482

Cores of early-type galaxies - the nature of dwarf spheroidal galaxies  

International Nuclear Information System (INIS)

The characteristics and evolution of dwarf spheroidal galaxies (DSGs) are modeled on the basis of high-resolution CCD photometry obtained with the Canada-France-Hawaii telescope and reported by Kormendy (1986). The data and the results of core-parameter correlation studies are presented in extensive graphs and discussed. It is inferred that at least some DSGs are formed by the stripping of gas from dwarf spiral and irregular galaxies, although internal gas processes may also be important. The hypothesis that DSGs represent the faint end of the elliptical-galaxy sequence appears to be ruled out. 50 references.

483

Core physics simulation for Wolsung Unit 1 ROP analysis  

International Nuclear Information System (INIS)

It has been issued that ROP(Regional Overpower Protection) for Wolsong Unit 1 needed to be reanalyzed due to the aging effect. Thermo-hydraulics and core simulation have to be performed for calculation of the fuel bundle power, channel power and detector signal production. PPV/MULTICELL/RFSP code system was used to calculate the power distribution for the ROP analysis. In this study, 232 cases out of 926 scenarios which include postulated accidents such as Startup after Short Shutdown, Shim Cases, Stepback, Insertion and Withdrawal of Reactivity Control Rods were simulated.

2001-05-01

484

Core localized toroidal Alfven eigenmodes destabilized by energetic ions in the CHS heliotron/torsatron  

Energy Technology Data Exchange (ETDEWEB)

Toroidal Alfven eigenmodes (TAE) destabilized by the pressure gradient of energetic alpha particles may expel the alpha particles before thermalization. TAE is important for tokamaks, and for helical systems (stellarators) as well. In CHS (compact helical system) TAE localized in the plasma core are destabilized when the plasma current is induced by co-injection of neutral beams. The observed TAE exhibits a ballooning nature. The internal structure of TAE was measured with a soft X-ray detector. The soft X-ray fluctuations level for TAE is too low to obtain the radial profiles of fluctuation intensities. (Tanaka, M.)

1999-09-01

485

CRC handbook of nuclear reactors calculations. Vol. II  

International Nuclear Information System (INIS)

This handbook breaks down the complex field of nuclear reactor calculations into major steps. Each step presents a detailed analysis of the problems to be solved, the parameters involved, and the elaborate computer programs developed to perform the calculations. This book bridges the gap between nuclear reactor theory and the implementation of that theory, including the problems to be encountered and the level of confidence that should be given to the methods described. Volume II: Monte Carlo Calculations for Nuclear Reactors. In-Core Management of Four Reactor Types. In-Core Management in CANDU-PHW Reactors. Reactor Dynamics. The Theory of Neutron Leakage in Reactor Lattices. Index.

486

A hierarchical lattice structure and formation mechanism of ZnO nano-tetrapods  

International Nuclear Information System (INIS)

The existence of characteristic longitudinal optical and transverse optical phonons of cubic ZnO in ZnO nano-tetrapods is determined by Raman spectroscopy and first-principles calculations. Stacking sequence change at the boundary of the core and legs is also identified by high-resolution transmission electron microscopy. Based on this experimental and theoretical evidence, we demonstrate that the lattice structure of ZnO nano-tetrapods is hierarchical with a zinc blende core connecting to four wurtzite legs. Furthermore, we establish the atomic configuration and propose a formation mechanism induced by Laplace pressure in the initial growth stage of ZnO nano-tetrapods.

2009-08-12

487

A Preliminary Analysis of SMART Reactor Core Using the COREDAX Code  

International Nuclear Information System (INIS)

The 3-D neutronics code COREDAX has been developed based on AFEN (Analytic Function Expansion Nodal) method for x-y-z geometry and for hex-z geometry. In this study, the COREDAX code, as a regulatory review tool independent of the designer's, was applied to the SMART reactor core that was designed by KAERI (Korea Atomic Energy Research Institute). For nuclear cross section generation, the HELIOS lattice code was used in this study. The preliminary results for steady state in various conditions are presented in this paper

2010-10-01

488

A NEM diffusion code for fuel management and time average core calculation  

International Nuclear Information System (INIS)

A computer code based on Nodal expansion method has been developed for solving two groups three dimensional diffusion equation. This code can be used for fuel management and time average core calculation. Explicit Xenon and fuel temperature estimation are also incorporated in this code. TAPP-4 phase-B physics experimental results were analyzed using this code and a code based on FD method. This paper gives the comparison of the observed data and the results obtained with this code and FD code. (author)

2005-11-01

489

Three integrated photovoltaic/sound barrier power plants. Construction and operational experience; Drei integrierte PV-Schallschutz Versuchsfelder. Bau und Erprobung  

Energy Technology Data Exchange (ETDEWEB)

After an international ideas competition by TNC Switzerland and Germany in 1996, six companies where given the opportunity to construct a prototype of their newly developed integrated PV-sound barrier concepts. The main goal was to develop highly integrated concepts, allowing the reduction of PV sound barrier systems costs, as well as the demonstration of specific concepts for different noise situations. This project is strongly correlated with a German project. Three of the concepts of the competition are demonstrated along a highway near Munich, constructed in 1997. The three Swiss installations had to be constructed at different locations, reflecting three typical situations for sound barriers. The first Swiss installation was the world first Bi-facial PV-sound barrier. It was built on a highway bridge at Wallisellen-Aubrugg in 1997. The operational experience of the installation is positive. But due to the different efficiencies of the two cell sides, its specific yield lies ...

2002-07-01

490

Megabreccias and associated carbonates of Rader Member, Capitan Reef Complex (Permian), Guadalupe Mountains, west Texas  

Energy Technology Data Exchange (ETDEWEB)

The Rader Member contains coarse allochthonous carbonate debris deposited basinward of a approx. = 500-m high angle of repose foreslope. Sheet-like megabreccias with internal channel fills up to 35 m thick are traceable 6.5 km along the reef escarpment (depositional strike) and extend 13 km southeast from the toe of slope into the Delaware basin. A prominent erosion surface at the base of the megabreccias may represent a major basin-sloping unconformity. At maximum thickness (65 m) of exposed Rader, three lithologic units are recognized in upward succession: (1) fine-grained, bioturbated limestones interbedded with fine-grained, laminated sandstones; (2) matrix- and clast-supported megabreccias comprised of chaotically oriented limestone blocks (up to 10 m across) with a fine-grained sandstone matrix; and (3) coarse to fine-grained carbonate turbidites interbedded with sandstones. The megabreccias truncate 30 m of section within 2.5 km of the shelf edge, completely ...

1987-05-01

491

Magnetic properties of laminated perovskite-like ferroelectromagnetics  

International Nuclear Information System (INIS)

Magnetic properties of layer ferromagnets against the thickness are investigated. Two new compounds served for studies: Bisub(6)Tisub(2)Nbsub(0,5)Fesub(2,5)Osub(18) and Bi_7Ti_3Fe_3O_2_1. The Moessbauer effect and the magnetic susceptibility measurements were applied in the experiment. The Faraday method was used in magnetic measurements in fields from 1 to 9,5 kOe. The results of Moessbauer measurements show that temperature dependence of the spectra is typical for compounds with superparamagnetic properties. The magnetic fields Hsub(n) on Fe"5"7 nuclei in Bisub(6)Tisub(2)Nbsub(0,5)Fesub(2,5)Osub(18) and Bi_7Ti_3Fe_3O_2_1 are similar and equal to 520+-10 kOe. Therefore it may be concluded that relaxation times of nuclear spins in these compounds are equal or close to each other. The lines of quadrupole splitting appear in spectra together at 20 K. The results of magnetic measurements show that the Curie-Weiss law is satisfied in the range of high temperatures for magnetic ...

1975-01-01

492

Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)  

Energy Technology Data Exchange (ETDEWEB)

To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and ...

1998-03-01

493

Development of a downhole seismic source with controlled waveform; Hakei seigyogata kochu shingen no kaihatsu  

Energy Technology Data Exchange (ETDEWEB)

A downhole seismic source which can output continuous waves having arbitrary waveforms was developed. The development was targeted to make tomographic exploration purposed to evaluate geological properties of a ground bed before and after constructing a building in a ground several hundred meters deep from the ground surface. The source is considered to be used in an environment consisting of soft rocks or more robust rocks and having no casing. It can be used in a well hole having a diameter of 100 mm, is capable of measuring P and S waves in a distance between well holes of up to 100 m, can be used at a depth of up to 500 m, and can output waveforms having seismic source spectra of up to 1000 Hz. An oscillation actuator using laminated piezo-electric elements was used for the oscillation element. The seismic source consists of a hydraulic device to clamp the equipment onto hole walls, piezo-electric elements as the oscillation element, and an inertia weight for ...

1997-05-27

494

Development of MHD generator channel walls, 1  

International Nuclear Information System (INIS)

Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanical supported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the MgO(MG-S) with Copper and Fe-Ni Alloy relaxation layers and MgO(MG-NC) with MgO-Ni Alloy ...

495

Verification of the CFD code FLUENT by post test calculation of the ROCOM experiment T665521; Validierung des CFD codes FLUENT anhand der Nachrechnung des ROCOM Experimentes T665521  

Energy Technology Data Exchange (ETDEWEB)

During the last years one focus of German PWR safety analysis was boron dilution events with the potential of reactivity transients. Coolant with a low boron concentration could be collected in localized areas of the reactor coolant system e.g. by separation of borated reactor coolant into highly concentrated and diluted fractions (inherent dilution) which can occur during reflux- condenser heat transfer after a small break loss of coolant accident with a limited availability of the emergency core cooling systems. The TUeV NORD SysTec was charged by German supervisory authorities with the assessment of the safety analyses of boron dilution events presented by the utilities. These analyses are based on the simulation of boron dilution and transport processes in conjunction with a number of dedicated experiments. The analyses shall demonstrate that boron dilution events cannot lead to recriticality of the core. Hence the boron concentration at ...

2005-05-01

496

Verification of the CFD code FLUENT by post test calculation of the ROCOM experiment T665521  

International Nuclear Information System (INIS)

During the last years one focus of German PWR safety analysis was boron dilution events with the potential of reactivity transients. Coolant with a low boron concentration could be collected in localized areas of the reactor coolant system e.g. by separation of borated reactor coolant into highly concentrated and diluted fractions (inherent dilution) which can occur during reflux- condenser heat transfer after a small break loss of coolant accident with a limited availability of the emergency core cooling systems. The TUeV NORD SysTec was charged by German supervisory authorities with the assessment of the safety analyses of boron dilution events presented by the utilities. These analyses are based on the simulation of boron dilution and transport processes in conjunction with a number of dedicated experiments. The analyses shall demonstrate that boron dilution events cannot lead to recriticality of the core. Hence the boron concentration at ...

2005-05-01

497

SUBMILLIMETER ARRAY OBSERVATIONS TOWARD THE MASSIVE STAR-FORMING CORE MM1 OF W75N  

International Nuclear Information System (INIS)

The massive star-forming core MM1 of W75N was observed using the Submillimeter Array with #approx#1'' and 2'' spatial resolutions at 217 and 347 GHz, respectively. From the 217 GHz continuum we found that the MM1 core consists of two sources, separated by about 1'': MM1a (#approx#0.6 M_s_u_n) and MM1b (#approx#1.4 M_s_u_n), located near the radio continuum sources VLA 2/VLA 3 and VLA 1, respectively. Within MM1b, two gas clumps were found to be expanding away from VLA 1 at about #+-#3 km s"-"1, as a result of the most recent star formation activity in the region. Observed molecular lines show emission peaks at two positions, MM1a and MM1b: sulfur-bearing species have emission peaks toward MM1a, but methanol and saturated species at MM1b. We identified high-temperature (#approx#200 K) gas toward MM1a and the hot core in MM1b. This segregation may result from the evolution of the massive star-forming ...

2010-11-10

498

HEXTRAN-SMABRE calculation of the 6th AER Benchmark, main steam line break in a WWER-440 NPP  

International Nuclear Information System (INIS)

The sixth AER benchmark is the second AER benchmark for couplings of the thermal hydraulic codes and three dimensional neutron kinetic core models. It concerns a double end break of one main steam line in a WWER-440 plant. The core is at the end of its first cycle in full power conditions. In VTT HEXTRAN2.9 is used for the core kinetics and dynamics and SMABRE4.8 as a thermal hydraulic model for the primary and secondary loop. The plant model for SMABRE consists mainly of two input models, Loviisa model and a standard WWER-440/213 plant model. The primary loop includes six separate loops, the pressure vessel is divided into six parallel channels in SMABRE and the whole core calculation is performed in the core with HEXTRAN. The horizontal steam generators are modelled with heat transfer tubes in five levels and vertically with two parts, riser and downcomer. With this kind of ...

2003-11-01

499

FORMATION PROCESS OF THE CIRCUMSTELLAR DISK: LONG-TERM SIMULATIONS IN THE MAIN ACCRETION PHASE OF STAR FORMATION  

International Nuclear Information System (INIS)

The formation and evolution of the circumstellar disk in unmagnetized molecular clouds is investigated using three-dimensional hydrodynamic simulations from the prestellar core until the end of the main accretion phase. In collapsing cloud cores, the first (adiabatic) core with a size of #approx#>3 AU forms prior to the formation of the protostar. At its formation, the first core has a thick disk-like structure and is mainly supported by the thermal pressure. After the protostar formation, it decreases the thickness gradually and becomes supported by the centrifugal force. We found that the first core is a precursor of the circumstellar disk with a size of >3 AU. This means that unmagnetized protoplanetary disk smaller than <3 AU does not exist. Reflecting the thermodynamics of the collapsing gas, at the protostar formation epoch, the first core (or the ...

2010-12-01

500

Comparison of steam-generator liquid holdup and core uncovery in two facilities of differing scale  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on Run SB-CL-05, a test similar to Semiscale Run S-UT-8. The test results show that the core was uncovered briefly during the accident and that the rods overheated at certain core locations. Liquid holdup on the upflow side of the steam-generator tubes was observed. After the loop seal cleared, the core refilled and the rods cooled. These behaviors were similar to those observed in the Semiscale run. The Large-Scale Test Facility (LSTF) Run SB-CL-06 is a counterpart test to Semiscale Run S-LH-01. The comparison of the results of both tests shows similar phenomena. The similarity of phenomena in these two facilities build confidence that these results can be expected to occur in a PWR. Similar holdup has now been observed in the 6 tubes of Semiscale and in the 141 tubes of LSTF. It is now more believable that holdup may occur in a full-scale steam generator with 3000 or more tubes. These results confirm ...

1987-01-01