From aerosol spectral optical depths ({tau}{sub p{lambda}}) at wavelengths in the range 380 to 1025 nm estimated at different locations in the near and far coastal regions of the Arabian sea adjoining the western coast of central India, the spatial and spectral characteristics of coastal aerosols and the effect of the proximity to the (urban) continent are investigated. The Aangstroem parameters are deduced from {tau}{sub p{lambda}} values. A significant increase, both in aerosol optical depths at shorter (visible) wavelengths ({lambda} {<=} 600 nm) and the Aangstroem wavelength exponent are observed in the near coastal regions, suggesting an increase in the (relative) concentration of sub micron particles, apparently of anthropogenic origin. The Aangstroem turbidity coefficient remains nearly steady spatially, indicating a (spatially) uniform loading of large particles. 31 refs, ...
Three kinds of thin AZ31 wrought magnesium alloys sheets were used in order to investigate the influence of the second phase particles on fracture toughness. From the theoretical model, the ratio of {lambda}{sub p}/d{sub p} would be estimated 5 {proportional_to} 6. On the other hand, from the microstructural observation, average particle spacing on each material was sample A: 13.1 {mu}m, sample B: 14.1, and sample C: 12 {mu}. In addition, average particle size on each sample was sample A: 2.1, sample B: 1.9, and sample C: 2.3 {mu}m. Therefore, the ratio of {lambda}{sub p}/d{sub p} calculated from fracture surface observation would be predicted 6 {proportional_to} 7. In comparison with the result of the prediction by theoretical analysis was in good agreement with the result of fracture toughness observation. It was found that the variation in plane-strain fracture toughness on AZ31 ...
Recent advances in self-amplified spontaneous emission (SASE) experiments stimulate interest in quantitative comparison of measurements with theory. In this paper we show that the widely used simulation code TDA3D, developed by Tran and Wurtele [Comput. Phys. Commun. 54, 263 (1989)] even though a single frequency code, can be used to determine the output power in the SASE process with excellent approximation in the exponential growth regime. The method applies when the gain is not very high, which is a special advantage, because when the gain is not very high, the analytical calculation is particularly difficult since the exponential growing term does not dominate. The analysis utilizes a scaling relation between the output power and the number of simulation particles in the code TDA3D: left-angle P right-angle=N_#lambda#"'/N_#lambda# left-angle P"'right-angle, where left-angle P right-angle is the output power and ...
An electroweak model with running coupling constants described by an energy dependent entire function is utraviolet complete and avoids unitarity violations for energies above 1 TeV. The action contains no physical scalar fields and no Higgs particle and the physical electroweak model fields are local and satisfy microcausality. The $W$ and $Z$ masses are compatible with a symmetry breaking $SU(2)_L\\times U(1)_Y \\rightarrow U(1)_{\\rm em}$, which retains a massless photon. The vertex couplings possess an energy scale $\\Lambda_W > 1$ TeV predicting scattering amplitudes that can be tested at the LHC.
We propose an X-ray mission called Xenia to search for decaying superweakly interacting Dark Matter particles (super-WIMP) with a mass in the keV range. The mission and its observation plan are capable of providing a major break through in our understanding of the nature of Dark Matter (DM). It will confirm, or reject, predictions of a number of particle physics models by increasing the sensitivity of the search for decaying DM by about two orders of magnitude through a wide-field imaging X-ray spectrometer in combination with a dedicated observation program. The proposed mission will provide unique limits on the mixing angle and mass of neutral leptons, right handed partners of neutrinos, which are important Dark Matter candidates. The existence of these particles is strongly motivated by observed neutrino flavor oscillations and the problem of baryon asymmetry of the Universe. In super-WIMP models, the details of the ...
We show, assuming the consistency of one measurable cardinal, that it is consistent for there to be exactly kappa+ many normal measures on the least measurable cardinal kappa. This answers a question of Stewart Baldwin. The methods generalize to higher cardinals, showing that the number of lambda strong compactness or lambda supercompactness measures on P_kappa(lambda) can be exactly lambda+, if lambda>kappa is a regular cardinal. We conclude with a list of open questions. Our proofs use a critical observation due to James Cummings.
This document deals with the couplings between the W boson and Z and gamma particles. WWZ and WW{gamma} vertex are predicted by the electroweak theory based on the symmetry group SU(2){sub L}*U(1){sub Y}, their existence is confirmed by the measurement of the production cross-section of W pairs at LEP. The effective values of the couplings are modified by the introduction of standard model particle loops at the vertex level, the impact on the coupling value is assessed to reach 10{sup -3}. These loops can also include beyond-the-standard-model particles, their impact is in the magnitude order of 10{sup -3} for most models. The fully description of these loops requires the values of 14 complex parameters whose measurement will give information about the existence of new particles. Nevertheless the number of events at LEP is not sufficient to measure all the parameters simultaneously. As a consequence the ...
Starting with a #LAMBDA#-nucleus potential, a semi-empirical formula, which gives a fairly satisfactory account of the ground state #LAMBDA#-binding energy of light hypernuclei, if the very light nuclei are ignored has been obtained. (author).
Apr 18, 2008 ... The FSS was produced by point-source filtering the individual detector data ... a 1-sigma noise map; and a coverage map giving the count of ...
Let ${\\mathcal F}_\\lambda(\\mathbb{S}^n)$ be the space of tensor densities on $\\mathbb{S}^n$ of degree $\\lambda$. We consider this space as an induced module of the nonunitary spherical series of the group $\\mathrm{SO}_0(n+1,1)$ and classify $(\\mathrm{so}(n+1,1),\\mathrm{SO}(n+1))$-sim$unitary submodules of ${\\mathcal F}_\\lambda(\\mathbb{S}^n)$ as a function of $\\lambda$.
We show that the recently measured asymmetry in helicity-angle spectra of the #LAMBDA#-hyperons, produced in the reaction pp#->#K"+#LAMBDA#p reaction, and the energy dependence of the total pp#->#K"+#LAMBDA#p cross-section can be explained consistently by the same #LAMBDA#p final-state interaction. Assuming that there is no final-state interaction in the #SIGMA#"0 p channel, as suggested by the available data for the reaction pp#->#K"+#SIGMA#"0p, we can also reproduce the energy dependence of the #LAMBDA#/#SIGMA#"0 production ratio and, in particular, the rather large ratio observed near the reaction thresholds. The nominal ratio of the #LAMBDA# and #SIGMA#"0 production amplitudes squared, i.e. when disregarding the final-state interaction, turns out to be about 3, which is in line with hyperon production data from proton and nuclear targets available ...
We consider spatially homogeneous (but generally non-isotropic) cosmologies in the recently proposed Horava-Lifshitz gravity and compare them to those of general relativity using Hamiltonian methods. In all cases, the problem is described by an effective point particle moving in a potential well with exponentially steep walls. Focusing on the closed-space cosmological model (Bianchi type IX), the mixmaster dynamics is now completely dominated by the quadratic Cotton tensor potential term for a very small volume of the universe. Unlike general relativity, where the evolution toward the initial singularity always exhibits chaotic behavior with alternating Kasner epochs, the anisotropic universe in Horava-Lifshitz gravity (with parameter lambda > 1/3) is described by a particle moving in a frozen potential well with fixed (but arbitrary) energy E. Alternating Kasner epochs still provide a good description of the early ...
We consider spatially homogeneous (but generally non-isotropic) cosmologies in the recently proposed Horava-Lifshitz gravity and compare them to those of general relativity using Hamiltonian methods. In all cases, the problem is described by an effective point particle moving in a potential well with exponentially steep walls. Focusing on the closed-space cosmological model (Bianchi type IX), the mixmaster dynamics is now completely dominated by the quadratic Cotton tensor potential term for a very small volume of the universe. Unlike general relativity, where the evolution toward the initial singularity always exhibits chaotic behavior with alternating Kasner epochs, the anisotropic universe in Horava-Lifshitz gravity (with parameter #lambda# > 1/3) is described by a particle moving in a frozen potential well with fixed (but arbitrary) energy E. Alternating Kasner epochs still provide a good description of the early ...
The production of the {lambda}- and {sigma}{sup 0}-hyperons has been measured via the pp{yields}pK{sup +}{lambda}/{sigma}{sup 0} reaction at the internal COSY-11 facility in the excess energy range between 14 and 60 MeV. The transition of the {lambda}/{sigma}{sup 0} cross-section ratio from about 28 at Q{<=}13 MeV to the high-energy level of about 2.5 is covered by the data showing a strong decrease of the ratio between 10 and 20 MeV excess energy. Effects from the final-state interactions in the p-{sigma}{sup 0} channel seem to be much smaller than in the p-{lambda} channel. Estimates of the effective range parameters are given for the N{lambda} and the N{sigma} systems. (orig.)
Given an invariant gauge potential and a periodic scalar potential \\tilde{V} on a Riemannian manifold \\tilde{M} with a discrete symmetry group \\Gamma, consider a \\Gamma-periodic quantum Hamiltonian \\tilde{H}=-\\tilde{\\Delta}_{B}+\\tilde{V} where \\tilde{\\Delta}_{B} is the Bochner Laplacian. Both the gauge group and the symmetry group \\Gamma can be noncommutative, and the gauge field need not vanish. On the other hand, \\Gamma is supposed to be of type I. To any unitary representation \\Lambda of \\Gamma one relates a Hamiltonian H^{\\Lambda}=-\\Delta_{B}^{\\Lambda}+V on M=\\tilde{M}/\\Gamma where V is the projection of \\tilde{V} to M. We describe a construction of the Bloch decomposition of \\tilde{H} into a direct integral whose components are H^{\\Lambda}, with \\Lambda running over the dual space \\hat{\\Gamma}. The evolution operator and the resolvent decompose correspondingly. Conversely, ...
A plasmid carrying the bacteriophage lambda lysis genes under lac control was subjected to hydroxylamine mutagenesis, and mutations eliminating the host lethality of the S gene were selected. DNA sequence...Full Text Available
BackgroundEscherichia coli strain EL350 contains chromosomally integrated phage lambda Red recombinase genes enabling this strain to be used for modifying the sequence...Full Text Available
Particle swarm optimization (PSO) is extensively used for real parameter optimization in diverse fields of study. This paper describes an application of PSO to the problem of designing a fractional-order proportional-integral-derivative (FOPID) controller whose parameters comprise proportionality constant, integral constant, derivative constant, integral order (lambda) and derivative order (delta). The presence of five optimizable parameters makes the task of designing a FOPID controller more challenging than conventional PID controller design. Our design method focuses on minimizing the Integral Time Absolute Error (ITAE) criterion. The digital realization of the deigned system utilizes the Tustin operator-based continued fraction expansion scheme. We carry out a simulation that illustrates the effectiveness of the proposed approach especially for realizing fractional-order plants. This paper also attempts to study the behavior of fractional ...
The binding energy parameter #lambda# plays an important role in common envelope evolution. Previous works have already pointed out that #lambda# varies throughout the stellar evolution, though it has been adopted as a constant in most of the population synthesis calculations. We have systematically calculated the binding energy parameter #lambda# for both Population I and Population II stars of masses 1-20 M _s_u_n, taking into account the contribution from the internal energy of stellar matter. We present fitting formulae for #lambda# that can be incorporated into future population synthesis investigations. We also briefly discuss the possible applications of the results in binary evolutions.
We consider the simplest scenario when black strings (cigars) penetrate the cosmological brane. As a result, the brane has a Swiss-cheese structure, with Schwarzschild black holes immersed in a Friedmann-Lema\\^{\\i}tre-Robertson-Walker brane. There is no dark radiation in the model, the cosmological regions of the brane are characterized by a cosmological constant $\\Lambda$ and flat spatial sections. Regardless of the value of $\\Lambda$, these brane-world universes forever expand and forever decelerate. The totality of source terms in the modified Einstein equation sum up to a dust, establishing a formal equivalence with the general relativistic Einstein-Straus model. However in this brane-world scenario with black strings the evolution of the cosmological fluid strongly depends on $\\Lambda$. For $\\Lambda$ less or equal to zero it has positive energy density $\\rho$ and negative pressure $p$ and at ...
We show that the recently measured asymmetry in helicity-angle spectra of the {lambda}-hyperons, produced in the reaction pp{yields}K{sup +}{lambda}p reaction, and the energy dependence of the total pp{yields}K{sup +}{lambda}p cross-section can be explained consistently by the same {lambda}p final-state interaction. Assuming that there is no final-state interaction in the {sigma}{sup 0} p channel, as suggested by the available data for the reaction pp{yields}K{sup +}{sigma}{sup 0}p, we can also reproduce the energy dependence of the {lambda}/{sigma}{sup 0} production ratio and, in particular, the rather large ratio observed near the reaction thresholds. The nominal ratio of the {lambda} and {sigma}{sup 0} production amplitudes squared, i.e. when disregarding the final-state interaction, turns out to be about 3, which is in line with hyperon production data from ...
The billiard motion inside an ellipsoid $Q \\subset \\Rset^{n+1}$ is completely integrable. Its phase space is a symplectic manifold of dimension $2n$, which is mostly foliated with Liouville tori of dimension $n$. The motion on each Liouville torus becomes just a parallel translation with some frequency $\\omega$ that varies with the torus. Besides, any billiard trajectory inside $Q$ is tangent to $n$ caustics $Q_{\\lambda_1},...,Q_{\\lambda_n}$, so the caustic parameters $\\lambda=(\\lambda_1,...,\\lambda_n)$ are integrals of the billiard map. The frequency map $\\lambda \\mapsto \\omega$ is a key tool to understand the structure of periodic billiard trajectories. In principle, it is well-defined only for nonsingular values of the caustic parameters. We present four conjectures, fully supported by numerical experiments. The last one gives rise to some lower bounds on the periods. ...
Efficient and precise ablation of soft tissue is needed for non-invasive dermatological and corneal surgeries. Previous research has revealed that smooth and efficient cutting of certain soft tissues and gelatin is possible using a Free Electron Laser (FEL) with a wavelength of #lambda#=6.45 #mu#m, tuned to the amide-II band of protein. Gelatin ablation experiments have been carried out using a mid-infrared FEL within the waveband #lambda#=5.6-6.7 #mu#m by changing the primary absorbers such as water (#lambda#=6.1 #mu#m) and protein (#lambda#=6.45 #mu#m). The gelatin with 80 wt% water was efficiently ablated by FEL irradiation with the waveband #lambda#=#approx#5.95-6.19 #mu#m. On the other hand, using irradiation within #lambda#=#approx#6.4-6.6 #mu#m, many small bubbles were observed in the irradiated volume, and the gelatin was not ablated but significantly ...
We examine the late-time behavior of initially expanding homogeneous cosmological models satisfying Einstein's equation with a positive cosmological constant ..lambda... It is shown that such models of all Bianchi types except IX exponentially evolve toward the de Sitter solution, with time scale (3/..lambda..)/sup 1/2/. The behavior of Bianchi type-IX universes is similar, provided that ..lambda.. is sufficiently large compared with spatial-curvature terms. Thus, a positive cosmological constant provides an effective means of isotropizing homogeneous universes.
We examine the late-time behavior of initially expanding homogeneous cosmological models satisfying Einstein's equation with a positive cosmological constant #LAMBDA#. It is shown that such models of all Bianchi types except IX exponentially evolve toward the de Sitter solution, with time scale (3/#LAMBDA#)/sup 1/2/. The behavior of Bianchi type-IX universes is similar, provided that #LAMBDA# is sufficiently large compared with spatial-curvature terms. Thus, a positive cosmological constant provides an effective means of isotropizing homogeneous universes.
FIG. 4. Power Spectral Density of the MAP W11 radiometer. The red and black traces are the power spectral density measurements of the two detectors on the ...
The electron-phonon coupling constant lambda has been calculated for vanadium. The electron energy bands and wave functions were obtained from a model augmented plane wave muffin-tin potential. The electron-phonon matrix elements were evaluated using the rigid-ion approximation and the measured phonon spectra. The results show that lambda is strongly affected by d-f scattering.
Predictions and measurements of a multimode waveguide interferometer operating in a fibre coupled, ``dual-mode'' regime are reported. With a 1.32 micrometer source, a complete switching cycle of the output beam is produced by a 10.0 nanometer incremental change in the 8.0 micrometer width of the hollow planar mirror waveguide. This equates to a fringe spacing of $\\sim\\lambda /130$. This is an order of magnitude smaller than previously reported results for this form of interferometer.
Fermi radii and velocities are determined by deconvoluting de Haas-van Alphen data. Comparison of these data with accurate augmented-plane-wave band-structure results establishes the reliability of the augmented-plane-wave calculations and allows a determination of the anisotropic many-body enhancement factor lambda(k). The Fermi-surface average of 1.33 suggests a large electron-electron contribution. Our anisotropic lambda(k) porvides a detailed test and guide for model calculations of many-body enhancement.
A new predictive framework for supersymmetry at the TeV scale is presented. The \\mu parameter of the MSSM is replaced by (\\lambda S), where S is a singlet field, and the axion becomes a heavy pseudoscalar, G, by adding a mass, m_G, by hand. The explicit breaking of Peccei--Quinn (PQ) symmetry is assumed to be sufficiently weak at the TeV scale that the only observable consequence is the mass m_G. Three models for the explicit PQ breaking are given; but the utility of this framework is that the predictions for all physics at the electroweak scale are independent of the particular model for PQ breaking. The MSSM parameters \\mu, B are replaced by \\lambda, A_\\lambda. Taking the scalar mass m_S^2 to be sufficiently small and \\lambda = A_\\lambda \\sin (2 \\beta) /2. Our framework leads to a theory similar to the MSSM, except that \\mu is predicted and there are light, ...
Recently the D{\\O} Collaboration reported an observation of like-sign charge asymmetry (CA), which is about $3.2 \\sigma$ deviation from the standard model (SM) prediction. Inspired by the observation we investigate the scalar unparticle effects, under the color charge of $SU(3)_c$ symmetry, in the CP violation in neutral B meson oscillations as well as the dispersive and absorptive parts of $\\bar B_q\\leftrightarrow B_q$ transition, which can be related to the CA directly. In order to illustrate the peculiar properties of unparticle, our analysis is carried out in two scenarios for the right-handed section: (I) $\\lambda_R=\\lambda_L$ and $U_D^R=U_D^L$, where $\\lambda_{L,R}$ and $U_D^{L,R}$ are the couplings and flavor mixing matrix of left- and right-handed section, respectively; (II) $\\lambda_R >> \\lambda_L$ and $U_D^R$ is completely a free parameter. In scenario I we found that the wrong- ...
Non-invasive methods are described for estimating local cerebal blood flows (LCBF) and local partition coefficients (L#lambda#) during inhalation of 30 % stable xenon gas (Xe) in oxygen during CT scanning. After the denitrogenation with pure oxygen breathing, 30 % Xe is inhaled for four minutes to minimize subanesthetic effects with a rubber facemask and the delivery system of Xe. Local time-#DELTA# Hounsfield units curve during the Xe wash-in and wash-out phase is utilized in order to calculate L#lambda# and LCBF using a least squares curve fitting analysis. Calculated L#lambda# and LCBF with the new method manifested reasonable distribution between the grey and white matters, and reproducibility was excellent in our study. Several case studies of patients with cerebral infarction are presented to demonstrate the characterization of L#lambda# and LCBF patterns in various tissues and theoretical grounds ...
Reaction of formation of 3, 5, 7, 3', 4', 5' - hexaoxiflavone - myricetin complexes with zirconium and hafnium ions has been the basis for development of luminescent method of determining these elements. Optimum conditions for complexing have been determined. For Hf they are : 8-9 HCl concentration, maximum fluorescence wave length (lambda fl.)of 520 nm, wave length of exciting light (lambda el) of 436 nm, for Zr lambda fl = 536nm, lambda el = 436 nm. Stable fluorescence establishes after 25 min. for Zr and after 15 min for Hf in the presence of 40% ethanol. Usage of various camouflage agents has permitted to attain high selectivity of the method. Possibility for determination of Zr with myricetin in the presence of a 10-time excess of Hf, Cr, Cu, 50-time excess of Mo and Ti is shown. Sensitivity of Zr determination is 2.0x10 #mu#g"-"2/ml, for Hf it is 9.0x10 #mu#g"-"3 and mineral waters.
If we decompose C1 using SVD the parameter covariance matrix can be inverted to ... However, we can analyze the parameter covariance matrix directly by ...
The F1F0 ATPase of Vibrio alginolyticus was cloned from a chromosomal lambda library. The unc operon, which contains the structural genes for the ATPase, was sequenced and shown to have a gene organization...Full Text Available
We introduce a family of rank functions and related notions of total transcendence for Galois types in abstract elementary classes. We focus, in particular, on abstract elementary classes satisfying the condition know as tameness (currently suspected to be a necessary condition for the development of a reasonable classification theory) where the connections between stability and total transcendence are most evident. As a byproduct, we obtain a partial upward stability transfer result for tame abstract elementary classes stable in a cardinal lambda satisfying lambda^{aleph_0}, a substantial generalization of a result of Baldwin, Kueker, and VanDieren.
pD10 is a 0.85 kb fragment with BamHI ends cloned in pSP64. It was sub-cloned from {lambda}D10 which was isolated from a genomic library constructed in {lambda}EMBL3 from a rodent human somatic cell hybrid. The probe was localized to 19q13.2-19qter on a panel of rodent human somatic cell hybrids. Co-dominant segregation was shown in 32 families of 280 individuals.
The summary of this report is: (1) The range of scales #LAMBDA# of a system is not a Lorentz invariant and can vary greatly for some systems. (2) There exists an optimum frame which minimizes #LAMBDA#. (3) We demonstrated speedup of x1000 for PIC simulation of relativistic beam interacting with electron background. (4) It is not in contradiction with the conventional scientific wisdom that 'complexity' is an invariant. (5) We identified three domains of application (laser-plasma acceleration, e-cloud in HEP accelerators, free electron lasers) for which speedup ranging from 2 to 4 orders of magnitude were demonstrated on toy problems.
Photoluminescence spectra for solutions containing Sm"3"+ isotope ions in heavy and normal water were studied in the wave length #lambda# = 500-700 nm and for absorption spectra and photoluminescence excitation spectra within the range of #lambda# = 260-600 nm. Differences in molar extinction coefficients for "1"4"4Sm"3"+ and "1"5"4Sm"3"+ were established both in the solutions with D_2O and by transition from the solutions with D_2O to the solutions with H_2O. New possible causes of the identified effects are discussed
Based on QCD conformal partial wave expansion to leading order conformal spin accuracy, we present the light-cone distribution amplitudes (DAs) of {sigma} and {lambda} baryons up to twist 6. It is concluded that fourteen independent DAs are needed to describe the valence three-quark states of the baryons at small transverse separations. The nonperturbative parameters relevant to the DAs are determined within the framework of QCD sum rule method. With the obtained DAs, a simple investigation on the electromagnetic form factors of these baryons are given. The magnetic moments of the baryons are estimated by fitting the magnetic form factor with the dipole formula.
We prove a cosmic no-hair theorem for Bianchi models in power-law inflation. Provided that the potential of an inflaton {phi} is exp({minus}{lambda}{kappa}{phi}) with 0{le}{lambda}{lt} {radical}2/3 , we find that the isotropic power-law solution is the unique attractor for any initially expanding Bianchi-type models except type IX. For Bianchi type IX, this conclusion is also true if the initial ratio of the vacuum energy to the maximum three-curvature is larger than one half.
Al, Ga and In complexing with methylthymol blue (H_6R) purified by gel filtration is studied. in the case of metal excess complexes with the ratio of components M:H_6R=2:1 with #lambda#=587(Al), 590(Ga) and 593 nm(In) appear. In the case of reacting agent excess complexes with the ratio of component 1:1 with #lambda#_m_a_x=480-490 (Al) and 480 nm(Ga, In) appear. The mechanism of complexing reactions is studied. Molar extinction coefficients and stability constants are calculated.
Dosimetry parameters such as deposition, clearance, retention, and translocation and dissolution of inhaled particles in and to different lung compartments may be important for the persistence of particles...Full Text Available
We study the line widths in the [O III]#lambda#5007 and H#alpha# lines for two groups of planetary nebulae in the Milky Way bulge based upon spectroscopy obtained at the Observatorio Astronomico Nacional in the Sierra San Pedro Martir (OAN-SPM) using the Manchester Echelle Spectrograph. The first sample includes objects early in their evolution, having high H#beta# luminosities, but [O III]#lambda#5007/H#beta# < 3. The second sample comprises objects late in their evolution, with He II #lambda#4686/H#beta#>0.5. These planetary nebulae represent evolutionary phases preceding and following those of the objects studied by Richer et al. in 2008. Our sample of planetary nebulae with weak [O III]#lambda#5007 has a line width distribution similar to that of the expansion velocities of the envelopes of asymptotic giant branch stars and shifted to systematically lower values as compared to the less evolved ...
A vertical cavity surface emitting laser that emits visible radiation is built upon a substrate, then having mirrors, the first mirror on top of the substrate; both sets of mirrors being a distributed Bragg reflector of either dielectrics or other materials which affect the resistivity or of semiconductors, such that the structure within the mirror comprises a plurality of sets, each having a thickness of {lambda}/2n where n is the index of refraction of each of the sets; each of the mirrors adjacent to spacers which are on either side of an optically active bulk or quantum well layer; and the spacers and the optically active layer are from one of the following material systems: In{sub z}(Al{sub y}Ga{sub 1{minus}y}){sub 1{minus}z}P, InAlGaAs, AlGaAs, InGaAs, or AlGaP/GaP, wherein the optically active region having a length equal to m {lambda}/2n{sub eff} where m is an integer and n{sub eff} is the effective index of refraction of the laser ...
It is well known that if one integrates a Schur function indexed by a partition $\\lambda$ over the symplectic (resp. orthogonal) group, the integral vanishes unless all parts of $\\lambda$ have even multiplicity (resp. all parts of $\\lambda$ are even). In a recent paper of Rains and Vazirani, Macdonald polynomial generalizations of these identities and several others were developed and proved using Hecke algebra techniques. However at $q=0$ (the Hall-Littlewood level), these approaches do not work, although one can obtain the results by taking the appropriate limit. In this paper, we develop a direct approach for dealing with this special case. This technique allows us to prove some identities that were not amenable to the Hecke algebra approach, as well as to explicitly control the nonzero values. Moreover, we are able to generalize some of the identities by introducing extra parameters. This leads us to a ...
We explore a planar GaAs/AlAs photonic microcavity using pump-probe spectroscopy. Free carriers are excited in the GaAs with short pump pulses. The time-resolved reflectivity is spectrally resolved short probe pulses. We show experimentally that the cavity resonance and its width depend on the dynamic refractive index of both the lambda-slab and the lambda/4 GaAs mirrors. We clearly observe a double exponential relaxation of both the the cavity resonance and its width, which is due to the different recombination timescales in the lambda-slab and the mirrors. In particular, the relaxation time due to the GaAs mirrors approaches the photon storage time of the cavity, a regime for which nonlinear effects have been predicted. The strongly non-single exponential behavior of the resonance and the width is in excellent agreement to a transfer-matrix model taking into account two recombination times. The change in width leads to a ...
The authors present a search for excited and exotic muon states {mu}*, conducted using an integrated luminosity of 371 pb{sup -1} of data collected in p{bar p} collisions at {radical}s = 1.96 TeV at the Tevatron with the CDF II detector. They search for associated production of {mu}{mu}* followed by the decay {mu}* {yields} {mu}{gamma}, resulting in the {mu}{mu}{gamma} final state. They compare the data to model predictions as a function of the mass of the excited muon M{sub {mu}*}, the compositeness energy scale {Lambda}, and the gauge coupling factor f. No signal above the standard model expectation is observed in the {mu}{gamma} mass spectrum. In the contact interaction model, they exclude 107 < M{sub {mu}*} < 853 GeV/c{sup 2} for {Lambda} = M{sub {mu}*}; in the gauge-mediated model, they exclude 100 < M{sub {mu}*} < 410 GeV/c{sup 2} for f/{Lambda} = 10{sup -2} GeV{sup -1}. These 95% ...
We examine the virtual effects of Kaluza-Klein (KK) states on Higgs physics in universal extra dimension models. We study the partial widths {Lambda}{sub h{yields}gg}, {Lambda}{sub h{yields}{gamma}{gamma}}, and {Lambda}{sub h{yields}{gamma}Z}, which are relevant for Higgs production and detection in future collider experiments. These interactions occur at one loop in the Standard Model, as do the KK contributions. We find that the deviations induced by the KK exchanges can be significant; for one extra dimension, the gg {yields} h production rate is increased by 10% - 85% for the mass of the first KK state in the range 500 {approx}> m{sub 1} {approx}> 1500 GeV, a region untested by current direct search and precision measurement constraints. The h {yields} {gamma}{gamma} decay width is decreased by {approx}< 20% in the same mass range. For two or more universal extra dimensions the results are cutoff ...
A model system, described by the consistent Vlasov-Poisson equations under periodical boundary conditions, has been studied numerically near the point of a marginal stability. The power laws, typical for a system, undergoing a second-order phase transition, hold in a vicinity of the critical point: (i) A {proportional_to} -{theta}{sup {beta}}, {beta}=1.907{+-}0.006 for {theta} {<=} 0, where A is the saturated amplitude of the marginally-stable mode; (ii) {chi} {proportional_to} {theta}{sup -{gamma}} as {theta} {yields} 0, {gamma}={gamma}{sub -}=1.020{+-}0.008 for {theta} < 0, and {gamma}={gamma}{sub +}=0.995{+-}0.020 for {theta} > 0, where {chi}={partial_derivative}A/{partial_derivative}F{sub 1} at F{sub 1} {yields} 0 is the susceptibility to external drive of the strain F{sub 1}; (iii) at {theta}=0 the system responds to external drive as A {proportional_to} F{sub 1}{sup 1/{delta}}, and {delta}=1.544{+-}0.002. {theta}=(<v{sup 2}>-<v{sub ...
The frequency dependence of the tunneling spectrum #alpha#"2F (#omega#) is analyzed in terms of electron pairing induced by exchange of acoustic plasmons in addition to the usual phonon-exchange mechanism. Analytic expressions are obtained for the electron self-energy, the tunneling function #alpha#"2F, and the electron pairing coupling lambda which determines the superconducting properties. The resulting theory is applied to recent tunneling data of Nb_3Sn in order to examine the anomalous discrepancies with the phonon density of states found by neutron scattering experiments. The results demonstrate how the high-temperature (T/sub c/ approx. 20 "0K) superconducting properties of A-15 compounds are enhanced by acoustic-plasmon contributions, and thus they reconcile these high transition temperatures with the relatively small values of the phonon part of lambda estimated from several independent experiments.
The use of a running coupling constant in renormalizable theories is well known, but the implementation of this idea for effective field theories with a dimensional coupling constant is in general less useful. Nevertheless there are multiple attempts to define running couplings including the effects of gravity, with varying conclusions. We sort through many of the issues involved, most particularly the idea of operator mixing and also the kinematics of crossing, using calculations in Yukawa and lambda phi^4 theory as illustrative examples. We remain in the perturbative regime. In some theories with a high permutation symmetry, such as lambda phi^4, a reasonable running coupling can be defined. However in most cases, such as Yukawa and gauge theories, a running coupling fails to correctly account for the energy dependence of the interaction strength. As a byproduct we also contrast on-shell and off-shell renormalizaton schemes and show that ...
Elastic and inelastic proton scattering has been measured in inverse kinematics on the unstable nucleus {sup 40}S. A phenomenological DWBA analysis yields a quadrupole deformation parameter {beta}{sub 2} = 0.35 {+-} 0.05 for the 2{sup +}{sub 1} state. Consistent phenomenological and microscopic proton scattering analyses have been applied to all even-even Sulfur isotopes from A = 32 to A = 40. The microscopic analysis used microscopic collective model densities and a modified Jeukenne-Lejeune-Mahaux effective interaction. This analysis suggests the presence of a neutron skin in the heavy sulfur isotopes. The analysis is consistent with normalization values for {lambda}{sub {upsilon}} and {lambda}{sub {omega}} of 0.95 for both the real and imaginary parts of the JLM potential. (author)
A study was made on interaction of vanadium (4) ions with dyes-pyrogallol red, brompyrogallol red and gallein- in the range of pH = 0-6. The maximal light absorption for gallein and brompyrogallol red is observed at pH=4 and #lambda#max = 545 nm and 560 nm respectively. The compound of vanadium (4) with pyrogalloe red is characterized by the maximal light absorption at pH=5 and #lambda#max=560 nm. Component ratio in all analyzed compounds is equal to 1:2. Molar extinction coefficients for compounds with gallein, pyrogallol red and brompyrogallol red are equal to 5000, 550 and 7400, and logarithms of stability constants - to 9.27, 13.17 and 13.25 respectively.
Let X be a group with identity e, let A be an infinite set of generators for X, and let (X,d_A) be the metric space with the word metric d_A induced by A. It is proved that if the diameter of the space is infinite, then for every positive integer h there are infinitely many elements x in X with d_A(e,x)=h. It is proved that if P is a nonempty finite set of prime numbers and A is the set of positive integers whose prime factors all belong to P, then the diameter of the metric space (\\Z,d_A) is infinite. Let \\lambda_A(h) denote the smallest positive integer x with d_A(e,x)=h. It is an open problem to compute \\lambda_A(h) and estimate its growth rate.
Radon concentrations were continuously measured outdoors, in living room and basement in 10-minute intervals for a month. The radon time series were analyzed by comparing algorithms to extract phase-space dynamical information. The application of fractal methods enabled to explore the chaotic nature of radon in the atmosphere. The computed fractal dimensions, such as Hurst exponent (H) from the rescaled range analysis, Lyapunov exponent (#lambda# ) and attractor dimension, provided estimates of the degree of chaotic behavior. The obtained low values of the Hurst exponent (0lambda# pointed out the grate sensitivity on initial conditions and appearing deterministic chaos by radon time variations. The calculated fractal dimensions of attractors indicated more influencing (meteorological) parameters on radon in the atmosphere. ...
A previous analysis aimed at underlining the importance of the relativistic electron beam quality for the performances of a Free Electron Laser (FEL) is continued in the paper by the study of the influence of the undulator field (wiggler) parameters and of the optical beam (and/or optical cavity) quality on the operation of a FEL. The importance of parameters such as K, #lambda#_u, g of the undulator, F, P_L, #nu#_c of the optical beam, and L, L_o_p_t and L_c_r of the optical cavity for the characteristics of the input radiation as P_o_u_t, G_o_p_t, and #eta# are analyzed and some relations between these parameters that will give the possibility to estimate the corresponding values are given. Some proposal for the design of a compact FEL in IR-spectral region, with #lambda# #approx# 230 #mu#m are given. (Author).
The shape and magnitude of the electrical resistivity [rho]([ital T]) is analyzed for four intermetallic compounds, and electron-phonon coupling constants [lambda] are extracted. ReO[sub 3] is particularly interesting because a sharp departure from the Bloch-Grueneisen shape can be attributed to high-frequency optical vibrations. The [lambda] values for the oxide metals seem too large to be consistent with the absence of superconductivity, but the results generally agree well with a conventional Fermi-liquid interpretation. The Hall coefficient [ital R][sub [ital H
A near-field microscope which operates in the rf/microwave frequency range is described. In this microscope, a scanning tunneling microscope (STM)-like tip rather than an aperture is used as a point-like evanescent field emitter. A spatial resolution of {approximately}5 {mu}m ({approximately}{lambda}/100000) is achieved in the current version. The design of the microscope as well as the principal factors which affect its performance are discussed. {copyright} {ital 1996 American Institute of Physics.}
A phenomenological analysis of lifetimes of bottom and charmed hadrons within the framework of the heavy quark expansion is performed. The baryon matrix element is evaluated using the bag model and the nonrelativistic quark model. We find that bottom-baryon lifetimes follow the pattern #tau#(#OMEGA#_b)#approx =##tau#(#XI#_b"-)>#tau#(#LAMBDA#_b)#approx =##tau#(#XI#_b"0). However, neither the lifetime ratio #tau#(#LAMBDA#_b)/#tau#(B_d) nor the absolute decay rates of the #LAMBDA#_b baryon and B mesons can be explained. One way of solving both difficulties is to allow the presence of linear 1/m_Q corrections by scaling the inclusive nonleptonic width with the fifth power of the hadron mass m_H__Q rather than the heavy quark mass m_Q. The hierarchy of bottom baryon lifetimes is dramatically modified to #tau#(#LAMBDA#_b)>#tau#(#XI#_b"-)>#tau#(#XI#_b"0)>#tau#(#OMEGA#_b): The longest-lived ...
The magnetic #beta#-spectrometer of the #pi# #sq root#2 type with 0.07% pulse resolution is used to measure the intensities of interval conversion electrons on L- and M-subshells of 70.45 keV "1"7"7 Ta gamma-transition. The results are analyzed and the values of mixing parameter #sigma#(E2/M1) and penetration parameter #lambda# are obtained.
Procedures are described for the use of synthetic oligonucleotides for Southern blot experiments and gene bank screening, and the effect of various mismatches on the efficiency of hybridization is demonstrated. The following topics are discussed: sensitivity vs. specificity, hybridization of a 12-mer to the lambda endolysin gene; hybridization of oligonucleotide probes to the E. coli lac operator; hybridization of synthetic probes to the CYC1 gene of yeast; and cloning eucaryotic genes. (HLW)
We have developed a new expression vector, pcIts ind+, based upon the powerful rightward promoter of bacteriophage lambda, which is controlled by a temperature-sensitive...Full Text Available
The problem on change of deuterium abundance in the process of galactic evolution (star evolution, supernova explosions, nucleosynthesis in supermassive objects) is considered. It is shown that the observable deuterium quantity in the interstellar medium must correspond to its cosmological abundance. This conclusion is independent of the rate of accretion of intergalactic gas by Galaxy. The effect of hypothetical pregalactic active objects on cosmological deuterium is small. It is poind out that observations of interstellar deuterium in absorbtion at lambda=91.6 cm are significant.
Extending the usual endpoint and midpoint interactions, we introduce numerous kinds of interactions, labelled by a parameter lambda and obtain a non-commutative and associative string field algebra by adding up all interactions. With this algebra we develop a covariant open bosonic string field theory, which reduces to Witten's open bosonic string field theory under a special string length choice.
Characterization and optimization of electron-beam parameters are important aspects of optimizing free-electron laser (FEL) performance. The visible spontaneous emission ({lambda}{approximately}650 nm) from the 5-meter long undulator of the Boeing FEL experiment can be characterized in sufficient detail with a streak/spectrometer to deduce time-resolved electron-beam spatial position and profile, micropulse duration, and energy. 7 refs., 13 figs., 2 tabs.
A noninvasive, simplified method using inhalation of stable xenon (Xe{sup s}) and computed tomographic (CT) scanning to estimate regional cerebral blood flow (rCBF) and regional partition coefficient (r{lambda}) is described. Twenty-four patients with cerebrovascular occlusive disease and six volunteer controls inhaled 30% Xe{sup s} and 70% oxygen for 180 seconds and exhaled for 144 seconds during serial CT scanning without denitrogenation. The end-tidal Xe{sup s} concentration was continuously monitored with a thermoconductivity analyzer to determine the build-up range (A value) and build-up rate constant (K value) for arteries with the curve fitting method. The time-CT number (Hounsfield unit) curve for cerebral tissue during the Xe{sup s} washin and washout phases was used to calculate r{lambda} and rCBF using least squares curve fitting analysis. The resultant r{lambda} and rCBF map demonstrated a reliable distribution ...
A noninvasive, simplified method using inhalation of stable xenon (Xe"s) and computed tomographic (CT) scanning to estimate regional cerebral blood flow (rCBF) and regional partition coefficient (r#lambda#) is described. Twenty-four patients with cerebrovascular occlusive disease and six volunteer controls inhaled 30% Xe"s and 70% oxygen for 180 seconds and exhaled for 144 seconds during serial CT scanning without denitrogenation. The end-tidal Xe"s concentration was continuously monitored with a thermoconductivity analyzer to determine the build-up range (A value) and build-up rate constant (K value) for arteries with the curve fitting method. The time-CT number (Hounsfield unit) curve for cerebral tissue during the Xe"s washin and washout phases was used to calculate r#lambda# and rCBF using least squares curve fitting analysis. The resultant r#lambda# and rCBF map demonstrated a reliable distribution between the gray and ...
Laser Doppler velocimetry and other photometric techniques are evaluated for measuring the average particle velocity in an ensemble of free-falling particles. The ability to obtain measurements in the presence of a radiant flux as high as 0.6 MW/m/sup 2/ was part of the evaluation. Optically dissimilar particles with diameters ranging from 0.1 mm to 1 mm were used in the study. Experimental results indicate that ensembles of particles do not behave as single isolated particles. The particle motion is dependent on particle volume fraction, and is quite unstable for falls greater than one meter.
Laser Doppler velocimetry and other photometric techniques are evaluated for measuring the average particle velocity in an ensemble of free-falling particles. The ability to obtain measurements in the presence of a radiant flux as high as 0.6 MW/m/sup 2/ was part of the evaluation. Optically dissimilar particles with diameters ranging from 0.1 mm to 1 mm were used in the study. Experimental results indicate that ensembles of particles do not behave as single isolated particles. The particle motion is dependent on particle volume fraction, and is quite unstable for falls greater than one meter.
The nuclear interaction probability of light charged particles in BaF[sub 2] crystals has been studied as a function of the incident particle energy. Light charged particles were identified in charge and mass by measuring their magnetic rigidity and their time-of-flight. The percentage of particles undergoing nuclear interactions has been measured for particles of charge from Z=1 to Z=6 and the experimental data are compared with the results of a model calculation. (orig.)
Biomass combustion is an important part in a sustainable energy system, but as well a source of submicron (particles < 1 #mu#m) particles in the air. Consequently, to obtain a good air quality together with increased biomass combustion there is a need for a better understanding of particle formation. This work is a part of a larger project about formation and emissions of particles from biofuel combustion. The report includes the work performed in the project during the year 2004. The aim of the project is to describe the release of inorganic components, which cause particle emissions, during combustion of single fuel particles of biofuel, e.g. wood pellets. The work is carried out by emission measurements, systematic combustion experiments and modelling work. The results are expected to contribute to the understanding of which parameters that influence the ...
Aims: To provide a significantly improved probability distribution for the H-test for periodicity in X-ray and $\\gamma$-ray arrival times, which is already extensively used by the $\\gamma$-ray pulsar community. Also, to obtain an analytical probability distribution for stacked test statistics in the case of a search for pulsed emission from an ensemble of pulsars where the significance per pulsar is relatively low, making individual detections insignificant on their own. This information is timely given the recent rapid discovery of new pulsars with the Fermi-LAT t $\\gamma$-ray telescope. Methods: Approximately $10^{14}$ realisations of the H-statistic ($H$) for random (white) noise is calculated from a random number generator for which the repitition cycle is $\\gg 10^{14}$. From these numbers the probability distribution $P(>H)$ is calculated. Results: The distribution of $H$ is is found to be exponential with parameter $\\lambda=0.4$ so that the cumulative ...
The structure of Poisson polynomial algebras of the type obtained as semiclassical limits of quantized coordinate rings is investigated. Sufficient conditions for a rational Poisson action of a torus on such an algebra to leave only finitely many Poisson prime ideals invariant are obtained. Combined with previous work of the first-named author, this establishes the Poisson Dixmier-Moeglin equivalence for large classes of Poisson polynomial rings, such as semiclassical limits of quantum matrices, quantum symplectic and euclidean spaces, quantum symmetric and antisymmetric matrices. For a similarly large class of Poisson polynomial rings, it is proved that the quotient field of the algebra (respectively, of any Poisson prime factor ring) is a rational function field $F(x_1,...,x_n)$ over the base field (respectively, over an extension field of the base field) with $\\{x_i,x_j\\}= \\lambda_{ij} x_ix_j$ for suitable scalars $\\lambda_{ij}$, thus ...
In this study, WO{sub 3} thin films were grown on glass substrates using an aqueous solution containing tungstate (NH{sub 4}){sub 2}WO{sub 4} as precursor. The substrate temperature incremented from 250 to 500 deg. C, by steps of 50 deg. C. The structural properties were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. Microprobe analyses showed that a balanced stoichiometric composition was obtained for thin films prepared at T{sub s} = 350 and 400 deg. C. The X-ray diffraction analyses showed different structure crystallography in function of the substrate temperature. Moreover, films deposited at 400 deg. C were annealed in air for 2 h at 450 and 500 deg. C, respectively and the structural changes due to heat treatment were studied. Finally, the optical properties of these films were carried out using optical measurements of transmittance T({lambda}) and reflectance R({lambda}) spectra in ...
In this study, SnO{sub 2} thin films have been grown using spray pyrolysis technique on glass substrates under a substrate temperature (T{sub s} = 440 {sup o}C). The precursors were methanol CH{sub 4}O and anhydrous tin tetrachloride. XRD analyses yielded strong (1 1 0)-(1 0 1)-(2 0 0) X-ray diffraction peaks which are characteristics to tetragonal crystals. Atomic Force Microscopy (AFM) analyses showed the existence of clusters with particular pyramidal shapes. The main part of this study concerns the optical measurements of transmittance T({lambda}) and reflectance R({lambda}) spectra inside 250-1800 nm domain. Conjoint optical and thermal properties were deduced using the Amlouk-Boubaker Opto-Thermal Expansivity {psi}{sub AB}. The obtained value: {psi}{sub AB} {approx} 23.4 m{sup 3} s{sup -1} helped situating the performance of the as-grown SnO{sub 2} compound among most known PV-T oxides like ZnO and TiO{sub 2}.
We study the evolution of an isolated, spherical halo of self-interacting dark matter (SIDM) in the gravothermal fluid formalism. We show that the thermal relaxation time, $t_r$, of a SIDM halo with a central density and velocity dispersion of a typical dwarf galaxy is significantly shorter than its age. We find a self-similar solution for the evolution of a SIDM halo in the limit where the mean free path between collisions, $\\lambda$, is everywhere longer than the gravitational scale height, $H$. Typical halos formed in this long mean free path regime relax to a quasistationary gravothermal density profile characterized by a nearly homogeneous core and a power-law halo where $\\rho \\propto r^{-2.19}$. We solve the more general time-dependent problem and show that the contracting core evolves to sufficiently high density that $\\lambda$ inevitably becomes smaller than $H$ in the innermost region. The core undergoes secular collapse to a ...
We study local radiation magnetohydrodynamic instabilities in static, optically thick, vertically stratified media with constant flux mean opacity. We include the effects of vertical gradients in a horizontal background magnetic field. Assuming rapid radiative diffusion, we use the zero gas pressure limit as an entry point for investigating the coupling between the photon bubble instability and the Parker instability. Apart from factors that depend on wavenumber orientation, the Parker instability exists for wavelengths longer than a characteristic wavelength lambda_{tran}, while photon bubbles exist for wavelengths shorter than lambda_{tran}. The growth rate in the Parker regime is independent of the orientation of the horizontal component of the wavenumber when radiative diffusion is rapid, but the range of Parker-like wavenumbers is extended if there exists strong horizontal shear between field lines (i.e. horizontal wavenumber perpendicular ...
Due to the increased computer power and advanced algorithms, quantum mechanical calculations based on Density Functional Theory are more and more widely used to solve real materials science problems. In this context large nonlinear generalized eigenvalue problems must be solved repeatedly to calculate the electronic ground state of a solid or molecule. Due to the nonlinear nature of this problem, an iterative solution of the eigenvalue problem can be more efficient provided it does not disturb the convergence of the self-consistent-field problem. The blocked Davidson method is one of the widely used and efficient schemes for that purpose, but its performance depends critically on the preconditioning, i.e. the procedure to improve the search space for an accurate solution. For more diagonally dominated problems, which appear typically for plane wave based pseudopotential calculations, the inverse of the diagonal of (H - ES) is used. However, for the more efficient 'augmented plane wave ...
Micron scale silicon nitride (SiNx) microdisk optical resonators fabricated on a silicon wafer are demonstrated with Q = 3.6 x 10^6 (finesse = 5 x 10^4) and an effective mode volume of 15 (\\lambda / n)^3 at wavelengths \\lambda ~ 852 nm resonant with the D2 transition manifold of cesium. A dilute hydrofluoric wet etch is shown to provide sensitive tuning of the microdisk optical resonances, and robust mounting of a fiber taper provides efficient fiber optic coupling to the SiNx microdisk cavities while allowing unfettered optical access for laser cooling and trapping of atoms. Initial measurement of a hybrid atom-cavity chip indicates that cesium adsorption on the surface of the SiNx microdisks results in significant red-detuning of the disk resonances. A technique for parallel integration of multiple (10) microdisks with a single optical fiber taper is also demonstrated.
Distributed Bragg reflectors (DBRs) composed of In_0_._5Al_0_._5P/In_0_._5(Al_yGa_1_-_y)_0_._5P quarter-wave layers have been prepared using metalorganic vapor phase epitaxy. The structures were grown over a wide range of high-index layer composition (0#<=#y#<=#0.6) and peak reflectivity wavelength (720 nm#<=##lambda##<=#565 nm, covering the spectrum from deep red to green). In all cases observed and calculated reflectance spectra were in excellent agreement. Using these DBRs, an undoped all-phosphide visible vertical cavity surface-emitting laser structure was grown. Under pulsed optical excitation at room temperature, lasing was obtained at a wavelength of #lambda##approx#670 nm, with a threshold power density comparable to that observed from similar structures prepared using AlAs/AlGaAs DBRs.
A newly developed 220 Mbps free-space 4-ary pulse position modulation (PPM) direct detection optical communication system is described. High speed GaAs integrated circuits were used to construct the PPM encoder and receiver electronic circuits. Both PPM slot and word timing recovery were provided in the PPM receiver. The optical transmitter consisted of an AlGaAs laser diode (Mitsubishi ML5702A, lambda=821nm) and a high speed driver unit. The photodetector consisted of a silicon avalanche photodiode (APD) (RCA30902S) preceded by an optical interference filter (delta lambda=10nm). Preliminary tests showed that the self-synchronized PPM receiver could achieve a receiver bit error rate of less than 10(exp -6) at 25 nW average received optical signal power or 360 photons per transmitted information bit. The relatively poor receiver sensitivity was believed to be caused by the insufficient electronic bandwidth of the APD preamplifier and the poor ...
Graphs with high symmetry or regularity are the main source for experimentally hard instances of the notoriously difficult graph isomorphism problem. In this paper, we study the computational complexity of isomorphism testing for line graphs of $t$-$(v,k,\\lambda)$ designs. For this class of highly regular graphs, we obtain a worst-case running time of $O(v^{\\log v + O(1)})$ for bounded parameters $t,k,\\lambda$. In a first step, our approach makes use of the Babai--Luks algorithm to compute canonical forms of $t$-designs. In a second step, we show that $t$-designs can be reconstructed from their line graphs in polynomial-time. The first is algebraic in nature, the second purely combinatorial. For both, profound structural knowledge in design theory is required. Our results extend earlier complexity results about isomorphism testing of graphs generated from Steiner triple systems and block designs.
Two overlapping cDNA clones encoding human DNA topoisomerase II were identified by two independent methods. In one, a human cDNA library in phage {lambda} was screened by hybridization with a mixed oligonucleotide probe encoding a stretch of seven amino acids found in yeast and Drosophila DNA topoisomerase II; in the other, a different human cDNA library in a {lambda}gt11 expression vector was screened for the expression of antigenic determinants that are recognized by rabbit antibodies specific to human DNA topoisomerase II. The entire coding sequences of the human DNA topoisomerase II gene were determined from these and several additional clones, identified through the use of the cloned human TOP2 gene sequences as probes. Hybridization between the cloned sequences and mRNA and genomic DNA indicates that the human enzyme is encoded by a single-copy gene. The location of the gene was mapped to chromosome 17q21-22 by in situ hybridization of a ...
We analyze archived Chandra and XMM-Newton X-ray observations of 536 Sloan Digital Sky Survey (SDSS) Data Release 5 (DR5) quasars (QSOs) at 1.7 <= z <= 2.7 in order to characterize the relative UV and X-ray spectral properties of QSOs that do not have broad UV absorption lines (BALs). We constrain the fraction of X-ray weak, non-BAL QSOs and find that such objects are rare; for example, sources underluminous by a factor of 10 comprise $\\la$2% of optically-selected SDSS QSOs. X-ray luminosities vary with respect to UV emission by a factor of $\\la$2 over several years for most sources. UV continuum reddening and the presence of narrow-line absorbing systems are not strongly associated with X-ray weakness in our sample. X-ray brightness is significantly correlated with UV emission line properties, so that relatively X-ray weak, non-BAL QSOs generally have weaker, blueshifted CIV$\\lambda$1549 emission and broader CIII]$\\lambda$1909 lines. ...
The properties and low pressure organometallic vapor phase epitaxy of Ga{sub x}In{sub 1{minus}x}P/(AlGa){sub 0.5}In{sub 0.5}P quantum well (QW) laser diode heterostructures with Al{sub 0.5}In{sub 0.5}P cladding layers, and having wavelength 614 < {lambda} < 690 nm, are described. At longer wavelengths ({lambda} > 660 nm), threshold current densities under 200 A/cm{sup 2} and efficiencies greater than 75% result from a biaxially-compressed GaInP QW active region. Although short wavelength laser performance is diminished by the poor electron confinement afforded by AlGaInP heterostructures, good 630 nm band performance, and extension into the 610 nm band, is achieved with strained, single QW active regions.
The aim of this study was to search for a sorbent that could act as an extraction phase and as a support for solid-matrix time-resolved luminescence (SMTRL). Four potential sorbents were investigated for this purpose using tetracycline (TC) as a model analyte. Sorbents prepared from C18 silica gel or calcium cross-linked pectin gel were able to extract TC from dilute solutions. Europium(III)-TC complex adsorbed on the surface of C18 generated the most intense TRL signal when measured at {lambda}{sub ex} = 388 nm and {lambda}{sub em} = 615 nm. This method achieved a 1 ng/ml limit of detection (LOD) with a 100 {mu}l sample solution in a repeated spotting mode. Hyphenation of sorbent extraction and SMTRL was demonstrated using C18. This method is suitable for screening of TC in foods or aqueous solutions and can be extended to other luminescent lanthanide-chelating analytes in physiological or environmental samples.
This dissertation describes a measurement of the rate ofnuclear muon capture by the proton, performed by the MuCap Collaborationusing a new technique based on a time projection chamber operating inultraclean, deuterium-depleted hydrogen gas at room temperature and 1 MPapressure. The hydrogen target's low gas density of 1 percent compared toliquid hydrogen is key to avoiding uncertainties that arise from theformation of muonic molecules. The capture rate was obtained from thedifference between the mu- disappearance rate in hydrogen--as determinedfrom data collected in the experiment's first physics run in fall2004--and the world averagefor the mu+ decay rate. After combining theresults of my analysis with the results from another independent analysisof the 2004 data, the muon capture rate from the hyperfine singlet groundstate of the mu-p atom is found to be Lambda_S = 725.0 +- 17.4 1/s, fromwhich the induced pseudoscalar coupling of the nucleon, ...
A radioactive particle was analyzed to discover the composition of the inactive material of the particle. The method uses the x-ray line spectrum of the K series caused by electron irradiation of the particle in the electron microscope. Iron and aluminum or silicon (the last two could not be distinguished) were found as inactive components in the particle. (D.L.C.)
A composition of matter to treat particles entrained in flue gas, is described comprising: a caustic liquid used to adjust resistivity of the entrained particles; and inert particulate matter supporting the caustic liquid for inhibiting chemical action of the caustic liquid until used to adjust the resistivity of the entrained particles, the inert particulate matter supporting sufficient caustic liquid to adjust the resistivity of the entrained particles.
Stabilized silver particles comprise particles comprising silver, a short-chain capping agent adsorbed on the particles, and a long-chain capping agent adsorbed on the particles. The short-chain capping agent is a first anionic polyelectrolyte having a molecular weight (Mw) of at most 10,000, and the long-chain capping agent is a second anionic polyelectrolyte having a molecular weight (Mw) of at least 25,000. The stabilized silver particles have a solid loading of metallic silver of at least 50 wt %.
A model is available in predicting flocculation frequencies between particles of various properties under the influence of a magnetic field. This model provides a basic understanding of fundamental phenomena, such as particle-particle and particle-collector interactions, occurring in HGMF (high gradient magnetic field), and will be extended to describe experimental data of particle flocculation and filtration and predict the performance of high- gradient magnetic filters. It is also expected that this model will eventually lead to a tool for design and optimization of magnetic filters for environmental, metallurgical, biochemical, and other applications.
A continuous-flow filter/concentrator for separating and/or concentrating particles in a fluid is disclosed. The filter is a three-port device an inlet port, an filter port and a concentrate port. The filter separates particles into two streams by the ratio of their dielectrophoretic mobility to their electrokinetic, advective, or diffusive mobility if the dominant transport mechanism is electrokinesis, advection, or diffusion, respectively.Also disclosed is a device for separating and/or concentrating particles by dielectrophoretic trapping of the particles.
The traveler participated in the discussions about the physics that can be learned in the experiments being planned, those presently running, or those recently completed by a growing number of major laboratories in Europe and the USA at the 'Workshop on NN Bremsstrahlung and Polarization Observables', where many representatives of these experimental programs were present. The traveler's research in this field is supported by a DOE Grant, and she has pioneered the early theoretical NN(lambda) treatments. In addition, she visited the Vrije University to collaborate with Professor Henk Blok on proton scattering from Zr-90 and neighboring nuclei. The traveler also visited NIKEF and discussed possible future experiments of mutual interest to be done at that laboratory.
A new class of solutions of the euclidean Einstein equations with #LAMBDA#-term ( A-class ) is found by solving the complex two-dimensional Kaehler Einstein equations with the following realization of complex metrics. The A-Class includes two gravitational instantons already known: the CP"2 and the Eguchi-Hanson metric, and allows a U(1)-generalized spin structure. It is shown that all Einstein euclidean two-axial Bianchi type IX metrics are exhausted by the Taub-NUT-de Sitter family and the A-class. (orig.).
The authors present the emitter efficiency results for the thin film 25 percent Ho YAG (Yttrium Aluminum Garnet, Y3Al5O12) selective emitter from 1000 to 1700 K with a platinum substrate. Spectral emittance and emissive power measurements were made (1.2 less than lambda less than 3.2 microns) and used to calculate the radiative efficiency. The radiative efficiency and power density of rare earth doped selective emitters are strongly dependent on temperature and experimental results indicate an optimum temperature (1650 K for Ho YAG) for thermophotovoltaic (TPV) applications.
We compare the existing observational data on type Ia supernovae with the evolutions of the Universe predicted by a one-parameter family of tachyon models which we have introduced recently [Phys. Rev. D 69, 123512 (2004)]. Among the set of the trajectories of the model which are compatible with the data there is a consistent subset for which the Universe ends up in a new type of soft cosmological singularity dubbed big brake. This opens up yet another scenario for the future history of the Universe besides the one predicted by the standard #LAMBDA#CDM model.
I summarize the extant direct and indirect data on the sky background SNAP will see at the North Ecliptic Pole over the wavelength range 0.4 < {lambda} < 1.7 {micro}m. At the spatial resolution of SNAP the sky background due to stars and galaxies is resolved, so the only source considered is zodiacal light. Several models are explored to provide interpolation in wavelength between the broadband data from HST and COBE observations. I believe the input data are now established well enough that the accuracy of the sky background presented here is sufficient for SNAP simulations, and that it will stand up to scrutiny by reviewers.
A rocket borne experiment to measure the temperature structure of the inner solar corona via the doppler broadening of the resonance hydrogen Lyman-..cap alpha.. (lambda1216A) radiation scattered by ambient neutral hydrogen atoms was attempted during the 16 Feb 1980 solar eclipse. Two Nike-Black Brant V sounding rockets carrying instrumented payloads were launched into the path of the advancing eclipse umbra from the San Marco satellite launch platform 3 miles off the east coast of Kenya.
We study the risk premium impact in the Perturbative Black Scholes model. The Perturbative Black Scholes model, developed by Scotti, is a subjective volatility model based on the classical Black Scholes one, where the volatility used by the trader is an estimation of the market one and contains measurement errors. In this article we analyze the correction to the pricing formulas due to the presence of an underlying drift different from the risk free return. We prove that, under some hypothesis on the parameters, if the asset price is a sub-martingale under historical probability, then the implied volatility presents a skewed structure, and the position of the minimum depends on the risk premium $\\lambda$.
It is pointed out that a recently claimed result regarding the removal of sharp structure in the electronic density of states N(E) of A-15 superconducting compounds at T approximately equal to Tsub(c) was in fact, shown earlier by one of the present authors (M.N.M.). Merely the variation of N(E) with energy in the vicinity of the Fermi level in these materials cannot explain their anomalous normal state properties and high values of lambda and Tsub(c). Rather a non-varying N(E) accompanied by phonon softening is in better agreement with experiment.
It is pointed out that a recently claimed result regarding the removal of sharp structure in the electronic density of states N(E) of A-15 superconducting compounds at T approximately equal to Tsub(c) was in fact, shown earlier by one of the present authors (M.N.M.). Merely the variation of N(E) with energy in the vicinity of the Fermi level in these materials cannot explain their anomalous normal state properties and high values of lambda and Tsub(c). Rather a non-varying N(E) accompanied by phonon softening is in better agreement with experiment. (author).
We review 25 specific heat measurements performed in Geneva on binary and pseudo-binary A-15 compounds. The rather extended temperature range allows us to make reliable estimates of several moments of the phonon spectrum which are required in the theory of superconductivity. The Tsub(c) expression of Allen and Dynes can then be used consistently to estimate the microscopic parameters lambda, eta, Nsub(bs) (Esub(F)), etc. The broad range of values reviewed permits to establish significant correlations between the parameters in stoichiometric and ordered compounds. (orig.).
Noninvasive and simplified methods for estimating regional cerebral blood flow (CBF) and regional partition coefficient ({lambda}) using the inhalation of stable xenon (Xe{sup s}) and computed tomographic (CT) scanning are described. Thirty percent Xe{sup s} in 70% oxygen was inhaled for 240 seconds and exhaled for 160 seconds during serial CT scanning without denitrogenation in 26 patients with cerebrovascular diseases and four volunteer controls. During the investigation, the end-tidal Xe{sup s} concentration was continuously monitored with a thermoconductivity analyzer to determine the build-up range (A value) and build-up rate constant (K value) of the artery by the curve fitting method. Calculated A and K values were corrected by the following formulae reported previously: for patients aged 0-20 years, A{sub e} = 0.75A{sub a} + 2.15, K{sub e} = 0.67K{sub a} + 0.69; 21-40 years, A{sub e} = 0.56A{sub a} + 3.24, K{sub e} = 0.38K{sub a} + 1.12; 41-60 years, A{sub ...
Noninvasive and simplified methods for estimating regional cerebral blood flow (CBF) and regional partition coefficient (#lambda#) using the inhalation of stable xenon (Xe"s) and computed tomographic (CT) scanning are described. Thirty percent Xe"s in 70% oxygen was inhaled for 240 seconds and exhaled for 160 seconds during serial CT scanning without denitrogenation in 26 patients with cerebrovascular diseases and four volunteer controls. During the investigation, the end-tidal Xe"s concentration was continuously monitored with a thermoconductivity analyzer to determine the build-up range (A value) and build-up rate constant (K value) of the artery by the curve fitting method. Calculated A and K values were corrected by the following formulae reported previously: for patients aged 0-20 years, A_e = 0.75A_a + 2.15, K_e = 0.67K_a + 0.69; 21-40 years, A_e = 0.56A_a + 3.24, K_e = 0.38K_a + 1.12; 41-60 years, A_e = 0.91A_a + 1.95, K_e = 0.38K_a + 1.32; over 61 years, ...
A powder neutron diffraction study has been carried out on /sup 239/PuN, which was reported to be antiferromagnetic below T = 13 K. No magnetic ordering has been detected at 4 K, the limit of the magnetic ordering which could be detected being ..mu..sub(ord) = 0.25 ..mu..sub(B) per Pu atom. Moreover a neutron scattering length determination of /sup 239/Pu was performed which gave a value of bsub(239Pu) = (0.81 +- 0.05) x 10/sup -12/ cm at a neutron wavelength lambda = 1.219 A.
This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), loading collapse ...
Jlab experiment E01-011, carried out in 2005 in JLab Hall C, is the second generation of the hypernuclear spectroscopy experiments by the (e,e{prime}K{sup +}) reaction. The (e,e{prime}K{sup +}) reaction is complimentary to the associated production reactions (K{sup -},{pi}{sup -}), ({pi}{sup +},K{sup +}) since, due to a larger momentum transfer to a hyperon, excitations of both spin-non-flip and spin-flip states are possible. The experiment uses high quality and continuous primary electron beam to produce neutron rich hypernuclei on various targets by the electroproduction. The experimental setup consists of splitter magnet, high resolution kaon spectrometer (HKS) and electron spectrometer (Enge) implemented in new configuration, the so called 'Tilt Method'. Production data was taken on multiple targets: CH{sub 2}, {sup 6}Li, {sup 7}Li, {sup 9}Be, {sup 10}B, {sup 12}C and {sup 28}Si. In present study the analysis of CH{sub 2}, {sup 12}C and {sup 28}Si is presented. ...
"American dominance in the study and development of high-energy particle physics may be seriously compromised, according to a report issued by the National Academy of Sciences, unless efforts are made to ensure that the next high-energy particle accelerator - the International Linear Collider (ILC) - will be constructed in the U.S.
The results of a search for fractionally charged particles produced in e/sup +/e/sup -/ annihilation at 29 GeV/c/sup 2/ are discussed. Results from cosmic-ray searches for fractionally charged particles, tachyons, and massive particles using the same detector are also presented.
We calculate the Bogolubov coefficients for a metric which describes the snapping of a cosmic string. If we insist on a matching condition for all times {\\it and} a particle interpretation, we find no particle creation.
We analyze transport through conical channels due to the difference in particle concentration on the two sides of the membrane. Because of the detailed balance, fluxes of non-interacting particles...Full Text Available
The authors' laboratory, using histochemicalmethods, previously identified two types of cholesterol-containing lipid particles in the extracellular spaces of human atherosclerotic lesions, one particle...Full Text Available
An exposure chamber is described for the quantifiable addition of fine and ultrafine aerosol particulate matter directly to cells and used to demonstrate the in vitro cytotoxicity of fine 1,4-naphthoquinone particles to murine lung epithelial cells. The electrostatic particulate dosage and exposure system (EPDExS) operates on the principle of electrostatic precipitation and is shown to deposit fine and ultrafine aerosol particles directly to cells with 100% efficiency for particle diameters in the range of 40-530nm. This range is not limited by the EPDExS, but rather by the aerosolization method used for this study. Numbers of particles deposited onto the cells are counted with a condensation particle counter, negating any need to calculate or estimate particle exposure. The process of particle introduction, assessed using Trypan blue dye ...
Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.
A model for energy transport in a solid particle cavity receiver is developed and applied to the design and analysis of a receiver for the Central Receiver Test Facility (CRTF), Albuquerque, New Mexico. The model gives thermal performance results - including particle temperatures, cavity efficiencies, and wall temperatures - which directly affect the economic and technical feasibility of a solid particle receiver. In addition, design criteria relevant to the configuration of a solid particle cavity receiver are developed. Results for CRTF indicate that at design conditions particle temperatures will exceed 1200/sup 0/K with cavity efficiencies on the order of 75%.
May 11, 2011 ... The Particle Environment Monitor (PEM) on NASA's Upper Atmosphere Research Satellite (UARS) measures the type, amount, energy, and ...
A characterization study was performed on monosodium titanate (MST) particles to determine the effect of high shear forces expected from the In-Tank Precipitation (ITP) process pumps on the particle size distribution. The particles were characterized using particle size analysis and scanning electron microscopy (SEM). No significant changes in particle size distributions were observed between as-received MST and after 2--4 hours of shearing. Both as-received and sheared MST particles contained a large percentage of porosity with pore sizes on the order of 500 to 2,000 Angstroms. Because of the large percentage of porosity, the overall surface area of the MST is dominated by the internal surfaces. The uranium and plutonium species present in the waste solution will have access to both interior and exterior surfaces. Therefore, uranium and plutonium loading should ...
The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise ...
"Physics in the United States is in a crisis that the country may lose the leadership in basic particle research in coming years, a report of the National Research Council warned." (1 page)
Aerosol particles are ubiquitous in the troposphere and exert an important influence on global climate and the environment. They affect climate through scattering, transmission, and absorption of...Full Text Available
A technique has been developed for high resolution alpha particle spectroscopy from track length determination in CR-39 plastic. On individual tracks an energy resolution deltaE close to the range straggling limit is obtainable. For 6 MeV alpha-particle deltaE is proportional 35 keV on individual particles and for groups of particles deltaE proportional 20 keV can be achieved using certain data selection criteria. At 100 keV on individual particles deltaE is proportional 20 keV. The analysis requires 1) a knowledge of the track-etch rate (Vsub(T))-range relationship and 2) a theoretical understanding of alpha-particle track structure in CR-39 as a function of particle energy, dip angle and degree of etching. The structure of alpha-particle etched tracks in CR-39 is described and two methods of analysis discussed. ...
Superconducting thin film particle detectors can be very attractive due to the low sensitivity to radiation damage. We describe the fabrication procedure and the characterization of Nb/Al bilayers as particle detectors. First steady and dynamical results are reported from tests of 5 MeV alpha-particle detection.
The possible role of space-like objects in elementary particle physics (and in quantum mechanics) is reviewed and discussed, mainly by exploiting the explicit consequences of the peculiar relativistic mechanics of Tachyons. Particular attention is paid: (i) to tachyons as the possible carriers of interactions; (ii) to the possibility of ''vacuum decays'' at the classical level; (iii) to a Lorentz-invariant bootstrap model; (iv) to the apparent shape of the tachyonic elementary particles and its possible connection with the de Broglie wave-particle dualism. (author).
Random motion of a particle, emitting and absorbing tachyons, is investigated. It is shown that if bradyon is in equilibrium with neutral gas, i.e. it absorbs and emits tachyons, which do not have any charges, tha particle with each absorption-emittance of a tachyon changes its energy and momentum, never varying its own mass, and as a result it moves like a brownian particle. Thus, bradyon, interacting with tachyon gas, increases its momentum continuously in agreement with the Einstein-Fokker-Planck type equation.
The case of spontaneous radiation of channeled ultrarelativistic particles is considered when the dipolarity condition is not satisfied. The change of the particle longitudinal velocity affecting the maximum radiation frequency is included. The angular and frequency characteristics of the radiation for superhigh energies are studied for the first time. It is shown that there is an optimum energy at which the radiation density is maximum. The influence of the angle at which electrons enter a crystal and of the beam divergence on the radiation is investigated. The problem of quasichanneled particle radiation and also the radiation in axis-plane transitions are considered. (author).
The periodic mode is analyzed together with two conventional boundary handling modes for particle swarm. By providing an infinite space that comprises periodic copies of original search space, it avoids possible disorganizing of particle swarm that is induced by the undesired mutations at the boundary. The results on benchmark functions show that particle swarm with periodic mode is capable of improving the search performance significantly, by compared with that of conventional modes and other algorithms.
We prove a theorem stating that a massive Majorana particle (a CPT-self-conjugate particle) with arbitrary spin J can possess only an anapole moment and multipoles of that. We also show that massless Majorana particles, except those of spin (1/2, do not have any single-photon electromagnetic form factor.
One of several methods to build YSZ electrolyte of SOFC is plasma spraying. This system heats particle to a melting point and then pushing them into target and forming a deposition. This paper presents heating studies of YSZ particle in plasma jet. By simple model it is shown that the required time such those YSZ particle with grain size of 50 ?m to be melt is around 12 x 10-4 second. (author)
The operation principle, construction and characteristics of the Bragg curve spectroscopy detector (BCS detector) are described. The electric field of the BCS detector is parallel to the particle trajectories. The detector was tested by 8.78 MeV and 6.02 MeV #alpha# particles from a ThC-ThC's source. The energy resolutions are 1.5% and 2.6% respectively for two groups of #alpha# particles, and the charge resolution is 2.7%. Further test experiments with heavy ions will be arranged.
Current applications of ..cap alpha..-particle spectrometry in post-irradiation research and reprocessing are reviewed. Implementation of procedures and techniques described in the literature to the particular samples at S.C.K./C.E.N. often results in a combined radiochemical method where ..cap alpha..-particle spectrometry is used to complement or enforce results obtained by other methods. Typical cases are reported and results obtained by different methods are compared to the results obtained by ..cap alpha..-particle spectrometry.
In this article a production method of a magnetorheological suspension composed with silicon steel particles of size 0.1-0.15 mm and 4% silicon content is described. Steel particles were dispersed in a conducting carrier of a by mixture of graphite particles with size 2-5 {mu}m and cedar wood oil. The filling factor of the suspension with the silicon steel particles and with graphite particles amounted to 0.25-0.40. Samples of this suspension were placed in a rectangular vessel with electrodes and used for the investigation of the Hall effect in magnetic field with induction 0-8 T, generated by Bitter-type magnet. A non-linear dependence of Hall voltage on the induction of the applied magnetic field and a hysteresis loop of this voltage in the shape of inclined digit eight were found. The causes of the observed effects is the ordering of silicon steel particles ...
The available data on isolated X-ray pulsars, their wind nebulae, and the supernova remnants which are connected to some of these sources are analyzed. It is shown that electric fields of neutron stars tear off charged particles from the surface of neutron star and trigger the acceleration of particles. The charged particles are accelerated mainly in the field of magneto-dipole radiation wave. Power and energy spectra of the charged particles depend on the strength of the magneto-dipole radiation. Therefore, the X-ray radiation is strongly dependent on the rate of rotational energy loss and weakly dependent on the electric field intensity. Coulomb interaction between the charged particles is the main factor for the energy loss and the X-ray spectra of the charged particles.
Dust particles in a plasma are charged negatively and are subject to various types of forces, including a drag force by plasma particles and a force due to the collective nature of a plasma. Dust particles are found in a sheath in laboratories balanced by the gravitational force and the electric force, while dust particles in space are ubiquitous, including planetary magnetospheres and interstellar space. Because of the novel nature of a complex system involving plasma particles and dust particles in a collective way, the dusty plasma is often called a complex plasma. The complex plasma is characterized by two distinctly different scales in time and in space. The plasma with electrons, ions and neutrals is characterized by the collective motion with a fast time scale and a short wavelength, while the dust particles move in a slow time scale ...
This paper describes the study of particles' dispersion in an isotropic turbulent flow. The particle's motion and the turbulent flow characteristics are calculated independently. While the particles' displacement is computed by the author's code, the flow is simulated with a commercial code : PowerFLOW. The particles and the flow are coupled through the relative velocity component of the aerodynamic force. When the simulated flow is turbulent, a turbulence regeneration model is used in order to get the flow instantaneous velocity. Validation of the method is done by comparing the particles' dispersion obtained with experimental results from literature and with the results calculated by FLUENT. Good accordance is found between numerical studies and experimental results. However, comparison between results of PowerFLOW coupled to the author's code and results from FLUENT shows ...
The available data of single X-ray pulsars, their wind nebulae, and the SNRs which are connected to some of these sources are analysed. It is shown that electric field intensity of neutron stars tears off charged particles from the surface of neutron star and triggers the acceleration of particles. The charged particles are accelerated mainly in the field of magnetodipole radiation wave. Power and energy spectra of the charged particles depend on the strength of the magnetodipole radiation. Therefore, the X-ray radiation is strongly dependent on the rate of rotational energy loss and weakly dependent on the electric field intensity. Coulomb interaction between the charged particles is the main factor for the energy loss and the X-ray spectra of the charged particles.
A possible receiver configuration is a cavity in which a falling sheet of solid particles is directly irradiated by the concentrated solar flux passing through the aperture. Regardless of the particular geometry, the radiative transfer within the falling particle curtain must be studied in order to determine the net radiative heating rate for the particles. A discrete ordinate radiative transfer model has been developed to predict the radiative coupling within the falling particle curtain. The model determines how much energy is absorbed by the particles, how much is transmitted to the rear wall of the receiver, and determines the effects of particle scattering and thermal emission on the net radiation absorbed by the particles. The model accounts for the directional nature of the radiation field, particle scattering, ...
A quantum secure direct communication scheme using dense coding is proposed. At first, the sender (Alice) prepares four-particle genuine entangled states and shares them with the receiver (Bob) by sending two particles in each entangled state to him. Secondly, Alice encodes secret information by performing the unitary transformations on her particles and transmits them to Bob. Finally, Bob performs the joint measurements on his particles to decode the secret information. The two-step security test guarantees the security of communication.
A flow field and particle trajectory in a HDD (Hard Disk Drive) between two rotating disks in axisymmetric enclosures is investigated using CFD code FLUENT/UNS. The RNG k-{epsilon} model is used as a turbulent model. In this study, the flow field between two disks are symmetric, and the flow field near the enclosure is very complex. Cross stream vectors are shown both for blowing and no blowing from the hub. The larger a particle, the more fast the particle deposits at the walls. In the case of blowing from the hub, the more fast the particle deposits at the walls. (author). 9 refs., 12 figs., 1 tab.
Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.
Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.
Processes of production and purification (necessary for fabricating fuel elements) of powdery uranium dioxide with particle size up to 1000 #mu#m and more have been studied. Developed is continuous process of UO_2 production with above particle size by converting uranium hexafloride into UO_2 solid particles in fluidized bed while their interaction with water vapor and hydrogen on the uranium dioxide nucleus material. The method allows to conduct continuous selection from the apparatus of UO_2 powder fraction with particle size near 1000 #mu#m without nucleus material additional feed.
This standard describes the procedure and equipment for in-place testing of HEPA filter systems by the single-particle, particle-size (SPPS) spectrometer method. This method provides the capability for evaluating the effectiveness (i.e., decontamination factor or DF) of systems consisting of one or more stages of HEPA filters against submicrometer aerosols in discrete particle-size ranges. It is particularly useful for testing of multi-stage HEPA filter installations and for testing of very large (50,000 cfm installed capacity) single-stage systems where it is desired to minimize the quantity of challenge aerosol required.
Alpha particle confinement is necessary for ignition of a D-T tokamak fusion plasma and for first wall protection. Due to high radiation backgrounds and temperatures, scintillators and semiconductor detectors may not be used to study alpha particles which are lost to the first wall during the D-T programs on JET and ITER. An alternative method of charged particle spectrometry capable of operation in these harsh environments, is proposed: it consists of thin foils of electrically isolated conductors with the flux of alpha particles determined by the positive current flowing from the foils. 2 refs., 3 figs.
In the case of inelastic scattering of alpha particles to the 3"+ state, the averaged angular distributions show a characteristic shape, corresponding to the excitation of such an unnatural parity state by alpha particles in the compound nucleus process. The modified Hauser-Feshbach cross-section calculations give a good description of the averaged distributions for the alpha particle scattering to the 3"+ state and the compound nucleus parameters could be extracted. The calculations of the compounds nucleus contributions to the other states in the case of 24 MeV alpha particle scattering from "2"8Si show that this contribution is not negligible and in the case of the scattering to the 4"+ state seems to be dominant. (Z.M.).
R-matrix analyses of neutron-induced reactions for many of the lightest p-shell nuclei are difficult due to a lack of distinct resonance structure in the reaction cross sections. Initial values for the required R-matrix parameters, E,sub(lambda) and ..gamma..sub(lambdac) for states in the compound system, can be obtained from shell model calculations. In the present work, the results of recent shell model calculations for the lithium isotopes have been used in R-matrix analyses of /sup 6/Li+n and /sup 7/Li+n reactions for E sub(n) < 8 MeV. Consequences of the shell model predictions for the level structure of /sup 7/Li and /sup 8/Li on the /sup 6/Li+n and /sup 7/Li+n reaction mechanisms and cross sections are discussed.
A scheme of evaluating a generalized three-photon excitation cross section #sigma#/sub (3)/ in neutral atomic argon at 3144.67 A is outlined. Three photons at this wavelength can excite the neutral argon atoms from the ground 3p"6 "1S_0 state to the 3p"54s'[1/2]_1"0 state. The fourth photon will ionize the argon atoms. Assuming linear polarization of the incident laser radiation, contributions from several channels in various energy-level schemes are summed in the evaluation of the transition probability. For a laser linewidth of #DELTA##lambda#/sub L/ = 1 A, our maximum numerical value of the computed result for the three-photon excitation cross section is #sigma#/sub (3)/ = 1.414 x 10/sup -80/ cm"6 s"2. .AE.
Based on a collisional-radiative model, an atomic-kinetic calculation of the gains on the 41.8-nm transitions of Pd-like xenon was performed for the plasma produced due to the interaction of a femtosecond laser pulse with gaseous xenon. The gains g(z,{tau}) averaged over the spatial and temporal coordinates were compared with the known gains which had been measured experimentally in Xe{sup 8+}. The amplification was shown to occur under the conditions of ionisation of the working ions, and the time of output radiation saturation depends on the time of Xe{sup 8+} transformation to higher-ionised ions. Our theoretical investigation enables determining the optimal pump parameters, at which the product of the gain g by the active medium length L is about 20, which exceeds the experimental gL value. (active media)
Determining the radial distribution of the thermal neutron field in the core of the Dalat reactor was done by the Cu foil activation method. The measured data were fitted by the least square method to determine some physical parameters of the reactor, as follows: 1. Laplacian: B_r"2 = (84.6 +- 5.5)10_-_4/,cm"2. 2. The effective radius: R_e_f_f = (27.6 +- 1.0)cm. 3. The extrapolation distance: #lambda#_r = (8.7 +- 1.0)cm. 4. The unequal coefficient of the effective multiplication: k_r = 1.77 +- 0.11. (author). 3 refs., 4 figs., 1 tab.
We provide a quantitative assessment of the probability distribution function of the concentration parameter of galaxy clusters. We do so by using the probability distribution function of halo formation times, calculated by means of the excursion set formalism, and a formation redshift-concentration scaling derived from results of N-body simulations. Our results suggest that the observed high concentrations of several clusters are quite unlikely in the standard Lambda CDM cosmological model, but that due to various inherent uncertainties, the statistical range of the predicted distribution may be significantly wider than commonly acknowledged. In addition, the probability distribution function of the Einstein radius of A1689 is evaluated, confirming that the observed value of ~45" +/- 5" is very improbable in the currently favoured cosmological model. If, however, a variance of ~20% in the theoretically predicted value of the virial radius is assumed, than the ...
Bedwyr is a generalization of logic programming that allows model checking directly on syntactic expressions possibly containing bindings. This system, written in OCaml, is a direct implementation of two recent advances in the theory of proof search. The first is centered on the fact that both finite success and finite failure can be captured in the sequent calculus by incorporating inference rules for {\\em definitions} that allow {\\em fixed points} to be explored. As a result, proof search in such a sequent calculus can capture simple model checking problems as well as may and must behavior in operational semantics. The second is that higher-order abstract syntax is directly supported using term-level $\\lambda$-binders and the quantifier known as $\
The direct addition of nickel powder to the reaction mixtures of 1,3-dialkyl-4,5-dioxoimidazolidine-2-thione (1) with the thionation Lawesson reagent produces [Ni{sup II}(R{sub 2}timdt{sup -}){sub 2}] (R{sub 2}timdt = 1,3-dialkylmidazolidine-2,4,5-trithione). These complexes belong to a new class of nickel-dithiolenes, showing remarkably high absorption ({epsilon} {approx} 80 000 dm{sup 3} mol{sup -1} cm{sup -1}, {lambda} {approx} 1000 nm) in the near-infrared region (near-IR), accompanied by high photochemical stability that makes these complexes promising near-IR dyes.
Amorphous Pd/sub 80/Si/sub 20/ was irradiated with fast neutrons (>1 MeV) to a fluence of 5 x 10/sup 20/ neutrons/cm/sup 2/. X-ray scattering intensities were measured before and after the irradiation with monochromatic Cu-K..cap alpha../sub 1/ rays. Scattered intensities for s>0.4 A/sup -1/ (s=2 sintheta/lambda) proved unaffected, while intensities were found remarkably enhanced for s<0.4 A/sup -1/ after the irradiation, i.e., in the small-angle region and the leading edge of the first halo. The results are discussed in relation to the structural anomalies in amorphous solids.
The structural and electronic properties of the A-15 compounds Nb_3Rh and Nb_3Ir were studied by means of escalar relativistic full-potential linearized augmented-plane wave (FP-LAPW) calculations with generalized gradient corrections. An investigation of the band structure of the hypothetical Nb_3Nb compound was also performed at the theoretical equilibrium lattice constant to ascertain the contribution of the nontransition elements on the B site in these A_3B-type compounds. Band structures and total densities of states were obtained. A rough estimate of the electron-phonon coupling parameter #lambda# as well as of the electronic specific-heat coefficient #gamma# were obtained for both Nb_3Rh and Nb_3Nb, which confirms that this latter is a low-temperature superconductor with T_c - 10K.
Judd-Ofelt parameters (?2 = 5.09?10-20, ?4 0.92?10-20, and ?6 = 0.63?10-20 cm2) and oscillator strengths of fundamental optical transitions involved in lasing at wavelength 1.54 ?m have been calculated for borosilicophosphate glass co-activated with Er3+ and Tb3+ ions based on experimental luminescence and absorption spectra and refractive indices. The results were used to determine the emission (6?10-23 cm2) and absorption (5?10-21 cm2) cross sections for lambda = 1.54 ?m and the gain cross section as a function of inverse population levels. (authors)
An FEL based energy driver for Inertial Confinement Fusion (ICF) is proposed. The key element of the scheme is free electron laser system. Novel technical solutions, namely, using of multichannel, multi-stage FEL amplifier with diaphragm focusing line, reveal a possibility to construct the FEL system operating at radiation wavelength {lambda} = 0.5 {mu}m and providing flush energy E = 1 MJ and brightness 4 x 10{sup 22} W cm{sup -2} sr{sup -1} within steering pulse duration {tau} {approximately} 0.1-2 ns. Total energy efficiency of the proposed ICF energy driver is about of 11% and repetition rate is 40 Hz. It is shown that the FEL based ICF energy driver may be constructed at the present level of accelerator technique R& D.
An ytterbium-169 high dose rate brachytherapy source, distinguished by an intensity-weighted average photon energy of 92.7 keV and a 32.015#+-#0.009 day half-life, is characterized in terms of the updated AAPM Task Group Report No. 43 specifications using the MCNP5 Monte Carlo computer code. In accordance with these specifications, the investigation included Monte Carlo simulations both in water and air with the in-air photon spectrum filtered to remove low-energy photons below 10 keV. TG-43 dosimetric data including S_K, D(r,#theta#), #LAMBDA#, g_L(r), F(r,#theta#), #phi#_a_n(r), and #phi#_a_n were calculated and statistical uncertainties in these parameters were derived and calculated in the appendix.
A study has been made of the colour reaction involved in the interaction or rare-earth elements with the reagent orthanyl K, the optimum conditions for the reaction being: pH=4.0-4.5 and lambda=660-670 nm. The ratio of components in the complex is Me:R=1:2. Consideration of the relative optical density values of the complex solutions as a function of the serial number of the rare-earth elements made it possible to recommend orthanyl K as a selective reagent for determining La, Ce, Pr and Nb in a mixture of Tu, Yb, Lu and Y oxides. The molar extinction coefficients, the sensitivity of the reaction and the concentration limits where Beer's law applies were calculated. Lanthanum was determined in a binary mixture with thulium and yttrium. (author).
The LCLS, a Free-Electron Laser (FEL) designed for operation at a first harmonic energy of 300 eV ({lambda} {congruent} 40{Angstrom}) in the Self-Amplified Spontaneous Emission (SASE) regime, will utilize electron bunches compressed down to durations of <0.5ps, or lengths of <150 {mu}. It is natural to inquire whether coherent radiation of this (and longer) wavelength will constitute a significant component of the total coherent output of the FEL. In this paper a determination of a simple upper bound on the IR that can be generated by the compressed bunches is outlines. Under the assumed operating parameters of the LCLS undulator, it is shown that that IR component of the coherent output should be strongly dominated by the x-ray component.
It is shown that a gun similar to that in the SSPX could demonstrate the high fields required for Pulsed Spheromak reactors merely by prolonging the pulse. Important considerations are choosing the voltage to exceed ohmic losses; designing the gun to avoid wasteful short-circuiting of current within the gun; and the injection efficiency factor, f, determined by the ''sag'' in the profile of {lambda} = {mu}{sub o}j/B. Typically f = 0.75 in experiments, giving an overall efficiency > 50 % if short-circuiting is avoided. Theoretical transport models agree qualitatively with the need for a finite gradient in h to pump in helicity by current-driven tearing modes and suggest that pressure-driven resistive modes would not compete with current-driven modes during a buildup to ohmic ignition.
The preliminary design of a far-infrared free-electron laser with a Coaxial Hybrid Iron (CHI) wiggler is presented. The CHI wiggler consists of a central rod and outer ring of alternating ferrite and dielectric spacers. A periodic wiggler field is produced when the CHI structure is immersed in an axial magnetic field. The design under investigation makes use of 1A, 1MV annular electron beam interacting with the TE{sub 01} coaxial waveguide mode at approximately 1 THz ({lambda} = 300 {mu}m). The nominal wiggler period is 0.5 cm and the inner and outer waveguide radii are 0.4 and 0.8 cm, respectively. An axial guide field of 5-10 kG is used. The device performance is modeled with slow-time-scale nonlinear code. Self fields and axial velocity spread are included in the model. Theoretical results will be presented.
Paper presents conceptual design of free electron laser (FEL) complex for industrial applications. The FEL complex consists of three. FEL oscillators with the optical output spanning the infrared (IR) and ultraviolet (UV) wave-lengths (#lambda# = 0.3...20 #mu#m) and with the average output power 10 - 20 kW. The driving beam for the FELs is produced by a superconducting accelerator. The electron beam is transported to the FELs via three beam lines (125 MeV and 2 x 250 MeV). Peculiar feature of the proposed complex is a high efficiency of the. FEL oscillators, up to 20 %. This becomes possible due to the use of quasi-continuous electron beam and the use of the time-dependent undulator tapering.
In this article we present the complete resummation of the leading chirally-enhanced corrections stemming from gluino-squark, chargino-sfermion and neutralino-sfermion loops in the MSSM with non-minimal sources of flavor-violation. We compute the finite renormalization of fermion masses and the CKM matrix induced by chirality-flipping self-energies. In the decoupling limit Msusy>>v, which is an excellent approximation to the full theory, we give analytic results for the effective gaugino(higgsino)-fermion-sfermion and the Higgs-fermion-fermion vertices. Using these vertices as effective Feynman rules, all leading chirally-enhanced corrections can consistently be included into perturbative calculations of Feynman amplitudes. We also give a generalized parametrization for the bare CKM matrix which extends the classic Wolfenstein parametrization to the case of complex parameters lambda and A.
In this work was made an assessment of the supramolecular structures presents into human breast tissue normal and pathological samples, as well as into two types of animals samples (tendon chicken and pork fat) using the small angle x-ray scattering (SAXS) technique. The scattering profiles of the samples were determined at the momentum transfer range O.150nm{sup -1}<=5:q(=4pi.sin({theta}/2)/{lambda})<=8.500nm{sup -1}. In this range, it was possible identify structures corresponding to collagen fibrils (glandular tissue) and to triacylglycerides (adipose tissue) from the correlation between the information extracted from the human breast tissues scattering profiles and those extracted from animals samples. (author)
The ASFIT (Anisotropic Source-Flux Iteration Technique) code was first developed in India about 1970 to solve the radiation transport equation represented in the form of coupled integral equations separating the spatial and energy-angular transmissions. The ASFIT code uses a nodal structure in the wavelength [lambda] domain in Compton units (CU) rather than in the energy domain. The ASFIT-VARI code is the latest version available from the Radiation Shielding Information Center. It incorporates variable dimensioning and has been adapted for use on MS-DOS personal computers using the Ryan-McFarland or Microsoft Version 5.0 FORTRAN compilers. While earlier versions used point cross sections (well suited for gamma-ray transport), the present version also allows multigroup cross sections for neutron and coupled neutron-gamma-ray transport.
Within the context of space-time (D-particle) foam in string/brane-theory it is demonstrated that it is possible to generate non-extensive statistics. The D-particle foam model involves point-like brane defects (D-particles), which provide the topologically non-trivial foamy structures of space-time. The D-particles can capture and emit stringy matter and this leads to a recoil of D-particles. It is indicated how one effect of such a recoil of D-particles is a back reaction on the space-time metric of Finsler type which is stochastic. We show that such a type of stochastic space-time foam can lead to cosmological effects similar to those induced by modifications of particle distributions within the framework of Tsallis entropies. The restrictions placed on the free parameters of the Finsler type metric are obtained from solving the Boltzmann ...
There are several approaches to describe flows with particles e.g. Lattice-Gas Automata (LGA), Lattice-Boltzmann method (LBM) or smoothed particle hydrodynamics (SPH). These approaches do not use fixed grids on which the Navier-Stokes equations are solved via e.g. finite volume method. The flow is simulated using a multitude of particles or particle density distributions, which interacts and due to statistical laws and an even more fundamental approach than the Navier-Stokes equation, the averaged flow variables can be derived. After a short summary of the most popular particle methods the new DMPC (Dissipative Multiple Particles Collision) approach will be presented. The DMPC-model eliminates some of the weak points of the established particle methods and shows high potential for more accurate CFD solution especially in areas where standard ...
Zinc oxide (ZnO) and alumina (Al2O3) particles are synthesized by the combustion of their volatilized acetylacetonate precursors in a premixed air-methane flame reactor. The particles are characterized by XRD, transmission electron microscopy, scanning mobility particle sizing and by measurement of the BET specific surface area. Pure (?-)alumina particles appear as dendritic aggregates with average mobile diameter 43-93 nm consisting of partly sintered, crystalline primary particles with diameter 7.1-8.8 nm and specific surface area 184-229 m2/g. Pure zinc oxide yields compact, crystalline particles with diameter 25-40 nm and specific surface area 27-43 m2/g. The crystallite size for both oxides, estimated from the XRD line broadening, is comparable to or slightly smaller than the primary particle diameter. The specific surface area ...
Particle shape is an important parameter in numerous civil, environmental, and petroleum engineering applications. In ground-water flow, the shape of individual particles comprising the soil affects the soil`s pore size distribution and, hence, the important flow characteristics such as hydraulic conductivity and headloss. A model for delineating the relative importance of particle size, particle shape, and porosity, (and their interactions), in explaining the variability of hydraulic conductivity of a granular porous medium is developed and tested. Three types of porous media are considered in this work: spherical glass beads; granular sand; and irregularly shaped, shredded glass particles. A reliable method for quantifying the three-dimensional shape and packing of large samples of irregular particles based on their angle of repose is presented. The results of ...
Formation of particles from heavy duty diesel and CNG vehicles was studied in laboratory conditions. PM, nano and soot mode particle emissions formed from buses of Euro 2-5 -emission levels were studied in relation to age and type approval characteristics of the vehicle. Characteristic particle emission factors from city driving were obtained by driving the buses on VTT's heavy duty chassis dynamometer applying the transient Braunschweig city cycle. The vehicles were a representative set of Euro 2 to 3 emission categories, supplemented with Euro 4-5 (EEV) -targeted CRT, CNG and DPF cars. Particle number emissions from Euro 4 to 5 buses were 1/100-1/1000 and mass emissions 1/10-1/100 of those of the current fleet. Particle emission from natural gas buses and after an advanced CRT trap contained almost entirely liquid < 60 nm nano particles, which ...
This paper discusses the application of a Computational Fluid Dynamics (CFD) code (FLUENT) to predict temperature and velocity profiles, and particle trajectories in an industrial fired by a low NO{sub x} pulverized coal swirl burner. The predictions of the code were compared to experimental measurements of gas temperature, particle size distribution, and particle velocities. The diagnostics employed were a suction pyrometer and a Particle Counter Sizer Velocimeter Probe (PCSV-P). Good agreement was found between the temperature predictions and the measurements. In situ particle size distributions were predicted accurately using the Baum and Street model with a swelling factor of zero. The numerical modeling indicated that the Type II flow issued from the burner could be transformed into Type III flow, by eliminating swirl from the primary air stream, which provided the preferred ...
In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe{sup 3+} and Fe{sup 2+}) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.
In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe"3"+ and Fe"2"+) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.
A composite material consisting of WC-Co particles in a steel matrix was fabricated by sintering mixtures of WC-Co particles and a steel powder and infiltrating the sintered pieces with a copper alloy. Its wear resistance and mechanical properties were studied as a function of the content in WC-Co particles and other characteristics of the composite material microstructure. Infiltration provided a simple means to obtain a strong cohesion between WC-Co particles and the steel matrix. An effective matrix protection against wear is obtained with relatively low additions of particles especially with a silica abrasive which is soft with respect to cemented carbide. The experimental results show that this material has good mechanical properties and wear resistance. Depending upon abrasion resistance, wear losses are reduced up to 10 times by a 30 vol% addition of cemented carbide ...
All-atom molecular dynamics simulations were used to study the morphology of polymer/inorganic composite particles prepared by heterocoagulation. The results were also compared to those of our previous study of the preparation of TiO2/poly(acrylic acid-co-methyl methacrylate) and Fe3O4/polystyrene composite particles. In the simulation system, polymer or inorganic particles were simulated by surface-charge-modified C60 or Na atoms. Through a combination of analysis of the radial distribution functions of charged atoms and snapshots of the equilibrated structure, three kinds of particle distributions were observed under different conditions. When the polymer and inorganic particles had opposite surface charges and their sizes were very different, the composite morphology showed a core-shell...
This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric lengths of the splat and crater scale linearly with the diameter of the impacting particle. It is hoped ...
A large detector with high redundancy is used to search for various types of anomalous particles in cosmic rays at sea level. The detector is sensitive to zenith angles between 45/sup 0/ and 90/sup 0/. Previously obtained limits on the fluxes of charge (1/3) and (2/3) particles are reduced to 2.9 x 10/sup -10/ and 2.6 x 10/sup -10/ cm/sup -2/sr /sup -1/ sec/sup -1/, respectively. The flux of ionizing tachyons is determined to be less than 2.4 x 10/sup -9/ cm/sup -2/ sr/sup -1/ sec/sup -1/. The massive-particle flux limit we obtain is inconsistent with previous claims of such particles assuming that these particles are isotropic in zenith angle.
A large detector with high redundancy is used to search for various types of anomalous particles in cosmic rays at sea level. The detector is sensitive to zenith angles between 45"0 and 90"0. Previously obtained limits on the fluxes of charge (1/3) and (2/3) particles are reduced to 2.9 x 10"-"1"0 and 2.6 x 10"-"1"0 cm"-"2sr "-"1 sec"-"1, respectively. The flux of ionizing tachyons is determined to be less than 2.4 x 10"-"9 cm"-"2 sr"-"1 sec"-"1. The massive-particle flux limit we obtain is inconsistent with previous claims of such particles assuming that these particles are isotropic in zenith angle.
Wood plastic composites (WPCs) are comprised of wood flour and thermoplastic polymer. The matrix is typically high-density polyethylene, poly (vinyl chloride), or polypropylene. The effect of morphology and micromechanics of wood flour particles on the mechanical performance of the bulk composite is a relatively unexplored area. The knowledge about the in situ properties of wood particles and the interfacial properties between the wood particles and the polymer matrix in the bio-composites is very limited. The objective of this work is to characterize the full-field deformation and strain distribution in and around wood particles embedded in polymer matrix. The mechanical tests are performed in small-scale tensile loading stage on thin composite samples containing 1-3 wood particles orient...
A new principle of particle trapping in the simple spherical cavity using both electric and magnetic components of radiofrequency electromagnetic field is proposed. The electric component of H {sub 12} oscillating mode drives the fast particle oscillations, while the magnetic component synchronously bends the trajectories to the cavity center. A specially developed theory of particle stability predicts dense and energetic electron cluster in the trap. Numerical simulations of particle dynamics in the complete electromagnetic field taking into account both space charge and particle-induced magnetic field are in good agreement with the analytic results, giving a density of 2.6*10{sup 1} electrons/cm{sup 3} and an average kinetic energy of around 30 keV at an operating frequency of 3 GHz. Being used at lower frequency, spherical cavity can trap protons and heavier ions too, but with ...
An exposure chamber is described for the quantifiable addition of fine and ultrafine aerosol particulate matter directly to cells and used to demonstrate the in vitro cytotoxicity of fine 1,4-naphthoquinone particles to murine lung epithelial cells. The electrostatic particulate dosage and exposure system (EPDExS) operates on the principle of electrostatic precipitation and is shown to deposit fine and ultrafine aerosol particles directly to cells with 100% efficiency for particle diameters in the range of 40-530nm. This range is not limited by the EPDExS, but rather by the aerosolization method used for this study. Numbers of particles deposited onto the cells are counted with a condensation particle counter, negating any need to calculate or estimate particle exposure. The process of par...
The translocation of particles from the alveolar compartment to the pleural space and tracheobronchial lymph nodes was investigated in rats over a 30 day period following the intrapulmonary instillation of 4 x 10/sup 8/ polystyrene microspheres (1.9 ..mu..m dia.). In initial studies, approx. =10/sup 4/ particles were found in the pleural space compartment on Days 1, 14 and 30 after particle deposition, and most of these were cell-associated. Subsequent pleural space studies indicated, however, that the particles found in this compartment were, at least in part, due to the pleural lavage technique, and, unlike observations reported for some fibers, the translocation of the particles used in our study to the pleural space does not represent an important lung clearance pathway. In regard to particle clearance to the tracheobronchial lymph nodes, the accumulation of ...
When a plasma becomes contaminated by foreign particles, generically referred to as dust, the result is called a dusty plasma. At the present time there is a great deal of interest in dusty plasmas because of their roles in terrestrial and extra-terrestrial processes - semiconductor processing, high temperature fusion experiments, stellar formation and the rings of Saturn. This thesis is concerned with the role of dust in processing type plasmas. In the following experiments, artificial dust is introduced into a parallel electrode plasma chamber. Ions and electrons in the plasma charge the dust particles and they become suspended in the plasma due to the balancing of electric and gravitational forces. By illuminating the suspended dust with laser light and using an extremely high speed camera fitted with a macro lens to look at the scattered light, the dust particles are observed directly. Specially written computer ...
We present local two-dimensional and three-dimensional hybrid numerical simulations of particles and gas in the midplane of protoplanetary disks (PPDs) using the Athena code. The particles are coupled to gas aerodynamically, with particle-to-gas feedback included. Magnetorotational turbulence is ignored as an approximation for the dead zone of PPDs, and we ignore particle self-gravity to study the precursor of planetesimal formation. Our simulations include a wide size distribution of particles, ranging from strongly coupled particles with dimensionless stopping time #tau#_s #ident to# #OMEGA#t_s_t_o_p = 10"-"4 (where #OMEGA# is the orbital frequency, t_s_t_o_p is the particle friction time) to marginally coupled ones with #tau#_s = 1, and a wide range of solid abundances. Our main results are as follows. (1) Particles ...
A considerable fraction of radioactivity entering the environment from different nuclear events is associated with particles. The impact of these events can only be fully assessed where there is some knowledge about the mobility of particle bound radionuclides entering the environment. The behavior of particulate radionuclides is dependent on several factors, including the physical, chemical and redox state of the environment, the characteristics of the particles (e.g., the chemical composition, crystallinity and particle size) and on the oxidative state of radionuclides contained in the particles. Six plutonium-containing particles stemming from Runit Island soil (Marshall Islands) were characterized using non-destructive analytical and microanalytical methods. By determining the activity of {sup 239,240}Pu and {sup 241}Am isotopes from their gamma peaks ...
Using the phasmid vector pSL5, the genomic DNA fragment of T. aquaticus YT1 which contained the thermostable DNA polymerase (Taq-polymerase) gene was cloned. The BglII fragment of this genome locus was subcloned in the BamHI site of the pUC19 plasmid. To optimize the Taq-polymerase gene expression in E. coli cells, the gene was cloned in the correct reading frame regarding the initiation ATG codon of the pPR-TGATG-1 expression vector. The gene expression in this vector was controlled by the phage lambda PR promoter and the temperature-sensitive phage lambda repressor. We used PCR to amplify the short 5'-end fragment of the Taq-polymerase gene coding for the part into which an artificial SacI site was introduced. This site has been used for cloning the PCR product into the pPR-TGATG-1 vector, and the missing gene part was cloned into the KpnI site of the PCR product from the natural cloned gene. The cells of the E. coli PVG-A1 strain, which was ...
The temperature dependent vibrational relaxation of the CO stretching mode of Rhodium dicarbonyl acetylacetonate (Rh(CO){sub 2}(acac)) and tungsten hexacarbonyl (W(CO){sub 6}) in dibutylphthalate (DBP) and 2-methylpentane (2-MP) were measured with IR pump and probe (P-P) experiments. The experiments were performed with {approximately}1.5 ps pulses generated by the Stanford superconducting accelerator pumped free electron laser (FEL). Measurements were performed on the Rh(CO){sub 2}(acac) CO asymmetric stretching mode at {lambda} = 4.98{mu}m from 10 K to 300 K. Both the parallel and magic angle probe polarizations decay curves are biexponential over the entire temperature range. The slow component (ranging from 40 ps at 300 K to 55 ps at 10K) is attributed to the population relaxations. For the fast component (ranging from 4-5 ps at 300 K to 13-15 ps at 10K), we propose a mechanism of spectral diffusion, in contrast to the previously proposed mechanisms of ...
Three cDNAs, designated IIA3, IIA3v, and IIA4, coding for P450s in the CYP2A gene subfamily were isolated from a {lambda}gt11 library prepared from human hepatic mRNA. Only three nucleotide differences and a single amino acid difference, Leu{sup 160}{yields}His, were found between IIA3 and IIA3v, indicating that they are probably allelic variants. IIA4 displayed 94% amino acid similarity with IIA3 and IIA3v. The three cDNAs were inserted into vaccinia virus, and recombinant viruses were used to infect human hepatoma Hep G2 cells. Only IIA3 was able to produce an enzyme that had a reduced CO-bound spectrum with a {lambda}{sub max} at 450 nm. This expressed enzyme was able to carry out coumarin 7-hydroxylation and ethoxycoumarin O-deethylation. cDNA-expressed IIA3v and IIA4 failed to incorporate heme and were enzymatically inactive. Analysis of IIA proteins in human liver microsomes, using antibody against rat IIA2, revealed two proteins of 49 ...
Three cDNAs, designated IIA3, IIA3v, and IIA4, coding for P450s in the CYP2A gene subfamily were isolated from a #lambda#gt11 library prepared from human hepatic mRNA. Only three nucleotide differences and a single amino acid difference, Leu"1"6"0#->#His, were found between IIA3 and IIA3v, indicating that they are probably allelic variants. IIA4 displayed 94% amino acid similarity with IIA3 and IIA3v. The three cDNAs were inserted into vaccinia virus, and recombinant viruses were used to infect human hepatoma Hep G2 cells. Only IIA3 was able to produce an enzyme that had a reduced CO-bound spectrum with a #lambda#_m_a_x at 450 nm. This expressed enzyme was able to carry out coumarin 7-hydroxylation and ethoxycoumarin O-deethylation. cDNA-expressed IIA3v and IIA4 failed to incorporate heme and were enzymatically inactive. Analysis of IIA proteins in human liver microsomes, using antibody against rat IIA2, revealed two proteins of 49 and 50 ...
In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C{sub 3}H{sub 8}O), water (H{sub 2}O) and zinc acetate (Z{sub n}(CH{sub 3}CO{sub 2}){sub 2}) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(lambda) and reflectance R(lambda) spectra. Conjoint optical and ...
A new series of heteroleptic cyclometalated platinum(II) complexes Pt-1a-f was synthesized, employing 2-arylpyridine (or 1-arylisoquinoline) (HC{sup L}AMDAN-1) and 1,3-bis(3,4-dibutoxyphenyl)propane-1,3-dione (HO{sup L}AMDAO-1) for cyclometalation and as ancillary ligands, respectively, and photoluminescent properties were investigated. Focusing on red-shifted phosphorescence, C{sup L}AMDAN ligands containing pi-extended aromatics and electron-rich heterocycles were examined. All obtained complexes exhibited photoluminescence at ambient temperature, and the emission maxima ranged from green (lambda{sub PL}=518 nm) to far red (lambda{sub PL}=708 nm). The large Stokes shifts of more than 100 nm and sub-microsecond or microsecond emission lifetimes revealed that these complexes are phosphorescent emissive. The quantum yield of Pt-1 ranged from 0.02 to 0.59 at ambient temperature and decreased as the emission maximum was red-shifted. In comparison ...
The ternary compound CuInS{sub 2} is attractive for solar cells due to its band gap of 1.54 eV which borders the optimum value necessary for conversion of a solar spectrum. Recently, works on thin film cells based on this material (ZnO/CuInS{sub 2}) has been reported to show efficiency as high as 11.4%. In this paper, the orientation and the morphology of CuInS{sub 2} sprayed films are determined by the means of X-ray diffraction and scanning electron microscopy. Sprayed CuInS{sub 2} films deposited onto a transparent Pyrex substrate with standard fabrication parameters show a chalcopyrite structure with a preferential orientation (1 1 2). A model based on the calculation of the relative dielectric function {epsilon} has been performed in order to obtain the profile of variation of this parameter and to understand the optical behavior of this material via its transmittance and reflectance in visible and near-infrared regions (0.35-2.5 {mu}m). In the same way, considering the ...
In the present thesis I discuss the hard spectator interaction amplitude in B {yields} {pi}{pi} at NLO i.e. at O({alpha}{sup 2}{sub s}). This special part of the amplitude, whose LO starts at O({alpha}{sub s}), is defined in the framework of QCD factorization. QCD factorization allows to separate the short- and the long-distance physics in leading power in an expansion in {lambda}{sub QCD}/m{sub b}, where the short-distance physics can be calculated in a perturbative expansion in {alpha}{sub s}. Compared to other parts of the amplitude hard spectator interactions are formally enhanced by the hard collinear scale {radical}({lambda}{sub QCD}m{sub b}), which occurs next to the mb-scale and leads to an enhancement of {alpha}{sub s}. From a technical point of view the main challenges of this calculation are due to the fact that we have to deal with Feynman integrals that come with up to five external legs and with three independent ratios of scales. ...
The authors would like to determine |V{sub cb}| from the exclusive semi-leptonic decay B{yields}D*lv. The differential decay rate is d{Lambda}/dw = G{sub F}{sup 2}/4{pi}{sup 3}(w{sup 2}-1){sup 1/2}m{sub D*}{sup 3} (m{sub B}-m{sub D*}){sup 2}G(w)|V{sub cb}|{sup 2}|F{sub B{yields}D*}(w)|{sup 2}, where w = v {center_dot} v{prime} and G(1) = 1. At zero recoil (w = 1) heavy-quark symmetry requires F{sub B{yields}D*}(1) to be close to 1. So, |V{sub cb}| is determined by dividing measurements of d{Lambda}/dw by the phase space and well-known factors, and extrapolating to w {yields} 1. This yields |V{sub cb}|F{sub B{yields}D*}(1), and F{sub B{yields}D*}(1) is taken from ''theory''. To date models [1] or a combination of a rigorous inequality plus judgement [2] have been used to estimate F{sub B{yields}D*}(1) - 1. In this work [3] they calculate F{sub B{yields}D*}(1) with lattice gauge theory, in the so-called ...
The purpose of this work is to determine the extent to which drill water might be expected to be imbibed by core samples taken from densely welded tuff. In a related experimental study conducted in G-Tunnel, drill water imbibition by the core samples was observed to be minimal. Calculations were carried out with the TOUGH code with the intent of corroborating the imbibition observations. Due to the absence of hydrologic data pertaining directly to G-Tunnel welded tuff, it was necessary to apply data from a similar formation. Because the moisture retention curve was not available for imbibition conditions, the drainage curve was applied to the model. The poor agreement between the observed and calculated imbibition data is attributed primarily to the inappropriateness of the drainage curve. Also significant is the value of absolute permeability (k) assumed in the model. Provided that the semi-log plot of the drainage and imbibition moisture retention curves are parallel within the ...
A simple and specific method has been developed for the simultaneous determination of the four major Cinchona alkaloids and their dihydroderivatives and pyridoxine hydrochloride (Vitamin B_6) by high-performance liquid chromatography (HPLC) with fluorescence detection (#lambda#_e_m=420 nm with #lambda#_e_x=330 nm). The chromatographic separation was performed on a Phenomenex Prodigy ODS column (5 #mu#m, 250 mmx3.2 mm i.d.), recommended for basic compounds, under isocratic reversed-phase conditions. The method allowed a good peak shape and an effective resolution of the tested compounds. The extraction of alkaloids from the Cinchona succirubra bark was carried out in mild and fast conditions (ambient temperature, 20 min) by ultrasonication. The procedure showed to be advantageous respect to a reference method, which involved Soxhlet extraction. The results were compared statistically by means of the Student's t-test and the variance ratio ...
Domestic, low-level exposure to radon gas is considered a major environmental lung-cancer hazard involving DNA damage to bronchial cells by α particles from radon progeny. At domestic exposure...Full Text Available
A new type of radiation which occurs when particles are accelerated in the field of a longitudinal wave and in a transverse magnetic field is studied. The characteristics of such spontaneous radiation are obtained, and the influence of collective effects on the radiation is analyzed. The application of the findings to the theory of free electron lasers is discussed. 8 references.
The variation of metallic particle size and sample porosity significantly alters the dynamic mechanical properties of high density granular composite materials processed using a cold isostatically pressed mixture of polytetrafluoroethylene (PTFE), aluminum (Al), and tungsten (W) powders. Quasistatic and dynamic experiments are performed with identical constituent mass fractions with variations in the size of the W particles and pressing conditions. The relatively weak polymer matrix allows the strength and fracture modes of this material to be governed by the granular type behavior of agglomerated metal particles. A higher ultimate compressive strength was observed in relatively high porosity samples with small W particles compared to those with coarse W particles in all experiments. Mesoscale granular force chains of the metallic particles explain this unusual ...
A strain of Chromobacterium violaceum has been isolated which produces bacteriophage tail-like particles in high numbers. The extracellular morphology and the intracellular arrangement...Full Text Available
Flow fields, temperature distributions, and particle trajectories in a 2-stage entrained-flow gasifier are calculated using a CFD code, FLUENT. Realizable k- {epsilon} model is used as a turbulent model. Because of swirling flow there appear recirculation regions near the burners. The characteristics of flow fields and temperature distributions in the gasifier are dependent on the swirl number of the system. Mean residence time of the particles in the reductor is inversely proportional to particle size, particle density and swirl number. As the swirl number is increasing, the particles injected from the combustor burners approach the wall near the combustor burners, which prevents the particles from entering the reductor and thus attaching the reductor wall. If the lower combustor burner angle is larger than the higher combustor burner angle for a given swirl ...
The measured result of charged multiplicity in cosmic-ray proton induced nuclear reaction from Chinese satellite emulsion is reported. The correlation of shower and heavy particles is discussed and compared with p-emulsion interactions.
Naturally occurring and contaminant ferromagnetic and ferrimagnetic particles have been found within or near cells, and might allow pulsed magnetic fields to create transient cell membrane opening ("pores")....Full Text Available
This work investigates the effect of excipient particle size on compaction properties of brittle, plastic and viscoelastic materials with and without added lubricants. Sieve cuts of Microcrystalline...Full Text Available
A dissipative particle swarm optimization is developed according to the self-organization of dissipative structure. The negative entropy is introduced to construct an opening dissipative system that is far-from-equilibrium so as to driving the irreversible evolution process with better fitness. The testing of two multimodal functions indicates it improves the performance effectively
Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma ...
An unexpectedly high probability of collisions between the fission particles and the atoms in an ionization chamber along the entire particle track causes a strong fluctuation of the shapes of the Bragg curves. This fluctuation imposes an upper limit of the charge resolution ..delta..Z/Z which can be achieved.
Transmission electron microscopy analysis (TEMA) was used to analyze the bronchoalveolar lavage fluid (BALF) of 262 subjects occupationally exposed (OE) to nonfibrous mineral particles (NFMP) and 42...Full Text Available
Bacterial pathogens use virulence strategies to invade epithelial barriers, but active processes of epithelial cells may also contribute to the endocytosis of microbial particles. To focus on the latter,...Full Text Available
Low pressure silane plasmas are known for their ability to synthesize silicon nanoparticles via gas phase nucleation. While in the past this particle formation has often been considered from the viewpoint of a contamination problem in semiconductor processing, we here describe a silane low pressure plasma that enables the synthesis of highly oriented, cubic-shaped silicon nanocrystals with a rather monodisperse size distribution. These silicon nanocubes have successfully been used in the manufacture of single nanoparticle vertical transistors. We discuss the advantages of this new paradigm of building nanoelectronic devices. The plasma synthesis process is characterized in more detail than in prior work. The particle nucleation, growth and shape evolution are studied. Results indicate that the process provides two spatially distinct zones: a diffuse plasma for particle growth and a constricted plasma zone for ...
... and mean rainfall rates, Rm, in the liquid hydrometeor layers using the .... large latitudinal movement of cirrus cloud cover with the changing seasons. ... We study the statistical distribution of PSCs by particle composition using .... the high resolution Cloud Particle Imager (CPI) and standard PMS 2D-C and ...
The general usefulness of neutron activation analysis (NAA) for samples containing the platinum group elements (PGE) and Au, either as major or trace constituents, is discussed. Charged particle activation is shown to be a viable or complementary alternative. Proton (6-10 MeV) and alpha particle (9-15 MeV) beams, produced in a tandem Van de Graaff accelerator, have been established to be the most effective choice. By taking advantage of the Coulomb barrier effect and the fact that many charged particle induced reactions have relatively large threshold values, the same instrumental technique can be applied, with minor modifications, to a wide range of materials.
The general usefulness of neutron activation analysis (NAA) for samples containing the platinum group elements and Au, either as major or trace constituents, is discussed. Charged particle activation is shown to be a viable or complementary alternative. Proton (6-10 MeV) and alpha particle (9-15 MeV) beams, produced in a Tandem van de Graaff accelerator, have been established to be the most effective choice. By taking advantage of the Coulomb barrier effect and the fact that many charged particle induced reactions have relatively large threshold values, the same instrumental technique can be applied, with minor modifications, to a wide range of materials.
The Knight shift of vanadium (KV) in fine V3Si particles was studied. The average diameter (\\bar{d}) ranged from 60 to 8000 A. The strong temperature dependence of the KV characteristic of high-Tc A-15 compounds was weakened in the particles. KV at 77 K increased with a decrease in \\bar{d}. The above-mentioned trends were consistent with a broadening of the sharp peak in the electronic density of states around the Fermi energy in particles resulting from a perturbation of the surface.
The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...
The possible role of space-like objects in elementary particle physics (and in quantum mechanics) is reviewed and discussed, mainly by exploiting the explicit consequences of the peculiar relativistic mechanics of Tachyons. Particular attention is paid: (i) to tachyons as the possible carriers of interactions; (ii) to the possibility of ''vacuum decays'' at the classical level; (iii) to a Lorentz-invariant bootstrap model; (iv) to the apparent shape of the tachyonic elementary particles and its possible connection with the de Broglie wave-particle dualism. (author).
... small water or ice particles by impaction ... flight recording; principally the hydrometeor charge unit ... capability of directing aircraft movements by radio ...
This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.
In the safety assessment of a potential repository for spent nuclear fuel, it is important to assess the consequences of a hypothetical leak of radionuclides through the seabed and into a waterborne transport phase. Radionuclides adsorbed to sediment particles may be transported great distances through the processes of sedimentation and resuspension. This study investigates the transport patterns of sediment particles of two different sizes, released in the Forsmark and Laxemar area. The results show that the closed waters around Forsmark to a higher degree makes the particles stay in the area close to the release points
The 'elementary' particle physics began in 1935, when Hideki Yukawa published his pioneering pi-meson theory, and the problem of strong interaction was finally solved 40 years later by the establishment of the Standard Model. The composite models of hadrons by the Sakata school and Sin-itiro Tomonaga's renormalization theory for quantum electrodynamics played essential roles for finding this beautiful solution. It is really surprising that it took only 40 years to solve such desperately difficult problem. The 'elementary' particle physics then split into two new fields, quark-hadron physics' and 'unified (ultimate) theory of particle physics', which are now 30 years old already. (author)
A survey of various mechanisms for particle emission in hydrodynamics is presented. First, in the case of sudden freeze out, the problem of negative contributions in the Cooper-Frye formula and ways out are presented. Then the separate chemical and thermal freeze out scenario is described and the necessity of its inclusion in a hydrodynamical code is discussed. Finally, we show how to formulate continuous particle emission in hydrodynamics and discuss extensively its consistency with data. We point out in various cases that the interpretation of data is quite influenced by the choice of the particle emission mechanism.
... operation, experimental data reduction, and application of PES results to studies related to estuarine and coastal sediment transport problems are ...
A method for the determination of different ''bare'' characteristics of the one-particle motion and one-particle basis in magic nuclei is described. The method is based on separating out the mixing with phonons from the phenomenological one-particle characteristics. By means of a generalization of the procedure for localization of the mass operator, relations linking the bare and phenomenological characteristics are obtained. The radial dependence of these characteristics in finite nuclei and the influence of the quasiparticle--phonon interaction on the phenomenological characteristics are studied. Calculations are performed for the neutrons in /sup 208/Pb.
We study diffusion of Cosmic Rays (CRs) in turbulent magnetic fields using test particle simulations. Electromagnetic fields are produced in direct numerical MHD simulations of turbulence and used as an input for particle tracing, particle feedback on turbulence being ignored. Statistical transport coefficients from the test particle runs are compared with earlier analytical predictions. We find qualitative correspondence between them in various aspects of CR diffusion. In the incompressible case, that we consider in this paper, the dominant scattering mechanism occurs to be the non-resonant mirror interactions with the slow-mode perturbations. Perpendicular transport roughly agrees with being produced by magnetic field wandering.
... 2-93 An Atmospheric Particle Emits Electromagnetic ... atmospheric water vapor produces a hydrometeor. ... subject to wind movement (either blowing ...
... that defines hydrometeor categories for the duration of the simulation ... and to observe the movement of any particular system ... particle settling occurred ...
... the vertical beam measures the movement of the ... be measured because the particle velocity in ... During precipitation, if the hydrometeor fall velocity is ...
The emission of light charged particles from heavy fragments of uranium fission induced by 153-MeV protons is studied. The probability of their emission is 2.7 x 10{sup - 2} per fission event. It is found that these particles affect the distribution of angles of fragment divergence and the angular distribution of heavy fragments with respect to the primary-proton beam. Experimental results suggest that the preequilibrium emission of particles is correlated with fission. Two mechanisms of interaction between 153-MeV protons and uranium nuclei are considered. 13 refs., 10 figs., 1 tab.
A nanoparticle generator based on the principle of electrical discharge (PALAS GFG-1000) was used to produce nanoparticles of different chemical natures. The fractions of electrically neutral particles were then measured by means of a Spectrometre de Mobilite Electrique Circulaire (SMEC, i.e. radial-flow mobility analyzer) for different operating conditions. The experimental results were compared with the theoretical values calculated from the Fuchs extended charge equilibrium model for spherical particles and agglomerates. For the smallest particles (below 20 nm), the deviations observed remain below 10%, and tend towards 20% for larger particles (over 35 nm).
The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 {micro}m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-{micro}m quartz particles; particles {ge}150 {micro}m formed clusters. Particles of 5 {micro}m completely dissolved by 900 C whereas particles {ge}150 {micro}m did not fully dissolve even when the temperature reached 1200 C. Sucrose addition had ...
A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions.
A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions. (orig.).
We have made preliminary estimates of charged particles background at the 100x100 GeV Photon Linear Collider with ultimate luminosity. The charged particles background due to electromagnetic processes is located mainly in the small-angle range of the detector. At large angles, the number of background particles is much smaller. Analysis of the background (at least, in the range under consideration) shows that background conditions for the VLEPP-based Photon Linear Collider are better than at the VLEPP electron-positron collider. ((orig.)).
Alpha particles, tritons, deuterons and protons accompanying /sup 252/Cf fission were registered in coincidence with both fission fragments by means of a system containing two-dimensional position-sensitive silicon detectors. Angular distributions, kinetic energy spectra of light charged particles as well as mass distributions of fission fragments in coincidence with light charged particles were measured. The experimental results are compared with some theoretical models.
Analytic expression is derived for X-ray fluorescence dependence on the particle size of powder and slurry media. The expression is obtained for a model of powder medium containing particles of different size and random distribution in the bulk of the sample. Limiting cases of homogeneous and slurry-like media are considered and expressions for calculation of the fluorescence intensity are derived. The results reasonably match the experiment for binary powder mixtures and thus provide evaluation of the powder particle size on the fluorescence intensity for multicomponent polydisperse powder medium
A multiple sampling dE/dx counter using a multiwire proportional chamber equipped with catbode pads was constructed for the multiple detection of dE/dx values along a particle trajectory. For low-energy particles this counter was proved to be useful as a Bragg-curve detector. At relativistic energies around E=14.6 GeV/nucleon good particle identification was obtained by cathode pad signals as well as anode signals for the range of projectile fragments from Z=1 (minimum ionization) up to a beam charge of Z=14. (orig.).
The motion of a test particle moving in an interior static spherically symmetric geometry is investigated. The author concludes that an oscillatory motion with the test particle changing its motion from a free fall towards the center to an outward radial motion can not exist for any static interior spherically symmetric model.
We consider a particle that is subject to a constant force and scatters inelastically on a vibrating periodically corrugated floor. At small friction and for small scatterers the dynamics is dominated by resonances forming spiral structures in phase space. These spiral modes lead to pronounced maxima and minima in the diffusion coefficient as a function of the vibration frequency, as is shown in computer simulations. Our theoretical predictions may be verified experimentally by studying transport of single granular particles on vibratory conveyors.
The motions of a classical free spinning point particle are extended to include the range of superluminal velocities. There is no formal change in the constraint-dependent functional relationship between observable mass and spin, i.e., trajectory, accompanying this extension. However, the theory now permits the specification, for superluminal velocities, of a linearly rising trajectory and naturally yields tachyon confinement. Therefore, unlike their subluminal counterparts, these tachyons can be considered candidates for elementary particle constituents.
Quark models of production of cumulative particles and the EMC effect are analyzed. It is shown that all these models are characterized by a universal relation between the spectrum of cumulative nucleons and the cross section for cumulative particles containing valence quarks of the nucleus. This relation is tested for the deuteron, and the role of secondary nuclear processes for heavy nuclei is discussed. It is noted that the ''sea'' cumulative particles (K"-, p-bar) are particularly important for understanding the nature of the difference between the structure functions of a nucleus and of a free nucleon.
A new method of particle identification of heavy ions through the measurement of the Bragg curve centroid and particle energy has been developed using a gas ionization chamber with a resistive anode layer. Z-resolutions comparable to the conventional ..delta..E-E counter telescope could be rather easily attained.
A new method of particle identification of heavy ions through the measurement of the Bragg curve centroid and particle energy has been developed using a gas ionization chamber with a resistive anode layer. Z-resolutions comparable to the conventional #DELTA#E-E counter telescope could be rather easily attained. (orig.).
A self-organizing particle swarm is presented. It works in dissipative state by employing the small inertia weight, according to experimental analysis on a simplified model, which with fast convergence. Then by recognizing and replacing inactive particles according to the process deviation information of device parameters, the fluctuation is introduced so as to driving the irreversible evolution process with better fitness. The testing on benchmark functions and an application example for device optimization with designed fitness function indicates it improves the performance effectively.
It is shown that a simple algorithm which exactly segregates between adiabatic and non-adiabatic electrons in particle-in-cell simulations of drift modes yields excellent conservation properties (e.g. particle number, energy) compared to the conventional df scheme. The removal of the free streaming term in the evolution of the marker weight is shown to be responsible for the improved linear and nonlinear properties of the simulated plasma.
The evaluation of the hazard posed to the skin by very small radioactive sources (diameter < 1mm) has become popularly known as the 'hot particle' problem in European and American nuclear reactor facilities. In this study, research to detect hot particle was performed in Wolsung Nuclear power plant (NPP) in Korea.
The evaluation of the hazard posed to the skin by very small radioactive sources (diameter < 1mm) has become popularly known as the 'hot particle' problem in European and American nuclear reactor facilities. In this study, research to detect hot particle was performed in Wolsung Nuclear power plant (NPP) in Korea.
Nano-sized particles of a lithium ion conductive solid electrolyte, LiTi{sub 2}(PO{sub 4}){sub 3}, were prepared by laser ablation. The obtained particles were ca. 10nm in diameter. X-ray powder diffraction and Raman spectroscopy showed that they were amorphous with local structure similar to the crystalline counterpart. They were crystallized by the heating at ca. 630{sup o}C. (author)
Zanker has recently presented nomographs for determining particle settling velocities in solid-liquid systems. These nomographs were based on the general correlations developed by Barnea and Mizrahi and Barnea and Mednick. This work presents an equation directly computing particle settling velocities, eliminating the uncertainty associated with nomographs.
Experimental and evaluated integral parameters derived from nuclear plus interference differential elastic scattering cross sections are presented for all projectile/target combinations of the particles p, d, t, /sup 3/He, and ..cap alpha... The data include reaction rates, average fractional energy losses per collision and per unit path length, and average laboratory scattering cosines. The resulting parameters are of potential use in analysis of charged-particle transport.
The effect of WC particle size with the addition of VC as a grain growth inhibitor was investigated during the liquid phase sintering of WC-Co system. With increasing WC particle size at the same VC content, the effect of grain growth inhibition was increased. Also, with increasing the VC content, the grain shape of WC was changed from the faceted shape to the distorted shape, and the step density of the WC grain was increased. (orig.)
It is shown that recuperator in which the thermal energy of particles is transformed into electric oue under drift in crossed fields is naturally coupled with dragontype magnetic confinement system, so the recuperation process can be initiated in the dragon magnetic field. A number of questions occuring under analysis of recuperator-dragon system is considered, including the dynamics of particle transfer to the recuperator, the share of particles entering the recuperator, the effect of rotational transform and the recuperation efficiency.
This report measured the rate of isothermal deposition of sub-micron particles of magnetite onto the surface of Alloy 800 at pH of 4.2-9.3 at Re=10,000 and a fluid temperature of 25C. Deposition is modelled as a two-step process, the transport of particles to the surface region followed by attachment to the surface.
Quark models of cumulative particle production and EMS effect are analyzed. All the models are characterized by a universal relationship between the spectrum of cumulative nucleons and the cross section of cumulative particles containing valence nuclear quarks. This relationship is tested for a deuteron. The role is discussed played by secondary nuclear processes for heavy nuclei. A special role of ''sea'' cumulative particles (K"-, p-bar) is pointed out in understanding the nature of the difference between the structure functions of a nucleus and of free nucleon.
Results of an experimental study of the interaction of 140 MeV alpha particles with /sup 90/Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from /sup 90/Zr(..cap alpha..,pp)X reactions, where both of the measured protons have energy ...
Results of an experimental study of the interaction of 140 MeV alpha particles with _9_0Zr nuclei resulting in fragmentation of the alpha particle are reported. The experimental observations of the study are analyzed and are found to show that alpha particle breakup reactions leading to at least 4-body final states, composed of two charged alpha particle fragments, contribute significantly to the singles yield of charged fragments observed at a fixed forward angle. The conclusions are based on coincidence measurements where one charged fragment is detected at a small forward angle which remains fixed, while the second charged fragment is detected at a series of coplanar secondary angles. The largest coincidence charged particle yield for the multiparticle final state events results from _9_0Zr(#alpha#,pp)X reactions, where both of the measured protons have energy distributions ...
The retrovirus-like particles of Drosophila are intermediates of retrotransposition of the transposable element copia. In these particles, a 39-nucleotide-long fragment from the 5' region of Drosophila...Full Text Available
A zinc-air battery in a case including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit.
A zinc-air battery in a case is described including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit. 7 figures.
Toroidicity Alfven Eigenmodes (TAE) in ITER can be driven unstable by two groups of energetic particles, the 3.5 MeV {alpha}-particle fusion products and the tangentially injected 1MeV beam ions. Stability conditions are established using the perturbative NOVA/NOVA-K codes. A quasi-linear diffusion model is then used to assess the induced redistribution of energetic particles.
Background: The difficulty of directly measuring cellular dose is a significant obstacle to application of target tissue dosimetry for nanoparticle and microparticle toxicity assessment. As a consequence, the target tissue paradigm for dosimetry and hazard assessment of nanoparticles has largely been ignored in favor of using metrics of exposure (e.g. ?g particle/mL culture medium, particle surface area/mL, particle number/mL). We have developed a computational model of solution particokinetics (sedimentation, diffusion) and dosimetry for non-interacting spherical particles and their agglomerates in monolayer cell culture systems. Particle transport to cells is calculated by simultaneous solution of Stokes Law (sedimentation) and the Stokes-Einstein equation (diffusion). Results: The In vitro Sedimentation, Diffusion and Dosimetry model (ISDD) was tested against measured transport ...
Reactions on the ionizing radiation of 14 Cladosporium cladosporioides strains were studied. Only 5 of them displayed radiotropizm. The ability of C. cladosporioides strains 4 and 5 with positive radiotropizm and museum C. cladosporioides strain 396 and its alb-mutant SM without positive radiotropizm to destruct radioactive particles of Chernobyl and explosion origin was studied. Two ways of radioactive particles destruction by C. cladosporioides were established, one of them is a direct way by fungal overgrowth of hot particles and the second one an indirect way only by fungal metabolites. Mycelium of the studied C. cladosporioides strains sorbed radionuclides from radioactive particles during cultivation on the liquid and agarized media. No certain inclinations of the individual strains to accumulation of radionuclides 137Cs or 152Eu were ascertained. PMID:12664550
We develop the formalism of a unified semi-microscopic description of low-energy proton and {alpha}-particle interaction with nuclei. We analyze elastic and inelastic proton scattering at the energy 25.05 MeV and {alpha}-particle scattering at the energy 104 MeV by the {sup 90}Zr nucleus. Information is obtained on differences in the deformation of the proton and neutron distributions. We study the energy dependence of the semi-microscopic {alpha}-particle potential including the energy dependence of the potential geometry.'' We analyze the change in angular distributions of elastically scattered {alpha} particles with increase of energy and the contribution to the scattering cross section from nucleon-nucleon correlations.
This paper describes a new time-resolved three-dimensional, three-component (3D-3C) measurement technique called wall-PIV. It was developed to assess near wall flow fields and shear rates near non-planar surfaces. The method is based on light absorption according to Beer-Lambert's law. The fluid containing a molecular dye and seeded with buoyant particles is illuminated by a monochromatic, diffuse light. Due to the dye, the depth of view is limited to the near wall layer. The three-dimensional particle positions can be reconstructed by the intensities of the particle's projection on an image sensor. The flow estimation is performed by a new algorithm, based on learned particle trajectories. Possible sources of measurement errors related to the wall-PIV technique are analyzed. The accuracy analysis was based on single particle experiments and a three-dimensional ...
The Green's function method in the Quasiparticle Time Blocking Approximation is applied to nuclear excitations in {sup 132}Sn and {sup 208}Pb. The calculations are performed self-consistently using a Skyrme interaction. The method combines the conventional RPA with an exact single-particle continuum treatment and considers in a consistent way the particle-phonon coupling. We reproduce not only the experimental values of low-and high-lying collective states but we also obtain fair agreement with the data of non-collective low-lying states that are strongly influenced by the particle-phonon coupling. (orig.)
Results of experimental investigation into radiation electromagnetic effect (REM) in samples of germanium crystals under approximately 40 MeV #alpha#-particle irradiation in a cyclotron are presented. A high level of excitation, volumetric character of generation of non-equilibrium carriers and formation of defects as well as the form of their spatial distribution are shown to result in some peculiarities of the EMF of the REM effect on the particle flux, fluence and sample parameters. Agreement of theoretical calculations, conducted with account of specificity of #alpha#-particle interaction with a crystal, and experimental data is obtained. It is revealed that the REM effect can be applied in obtaining data on spatial distribution of non-equilibrium carrier concentrations along the particle trajectory in the crystal.
Many-particle confinement (localization) is studied for a 1D system of spinless fermions with nearest-neighbour hopping and interaction, or equivalently, for an anisotropic Heisenberg spin-1/2 chain. This system is frequently used to model quantum computers with perpetually coupled qubits. We construct a bounded sequence of site energies that leads to strong single-particle confinement of all states on individual sites. We show that this sequence also leads to a confinement of all many-particle states in an infinite system for a time that scales as a high power of the reciprocal hopping integral. The confinement is achieved for strong interaction between the particles while keeping the overall bandwidth of site energies comparatively small. The results show the viability of quantum computing with time-independent qubit coupling.
In order to apply chemical-looping combustion to a practical power plant, carbon deposition on the solid particle is one of the key problems to be overcome. Six kinds of solid particles were examined to clarify the kinetic behavior of carbon deposition. The effects of the solid composition, feed gas composition, and reaction temperature on carbon deposition were investigated by thermogravimetrical reactor on the basis of NiO/YSZ particle. From the viewpoints of both reactivity and resistance against carbon deposition, the particle of NiO mixed with YSZ (i.e., yttria-stabilized zirconia) was found to be a good candidate for chemical-looping combustion. It has been observed that carbon deposition could be completely avoided with very low concentration of water vapor. By means of a proposed model, the condition that carbon deposition would be avoided was identified. 12 refs., 8 figs., 2 tabs.
This paper presents a new method of extracting biologic particles from a mixture of particles. The method is based on the pumping effect in a p-shaped ultrasonic actuator, which has a gap between its two vibrating metal plates. An adhesive tape is placed at a proper position in the gap. Due to the pumping effect which is induced by the sound field in the gap, the particles with smaller mass and radius in the mixture can be pumped up to reach the adhesive tape; while the ones with larger mass cannot. Therefore, the particles with smaller mass and radius can be extracted from the mixture. A theoretical model which can well explain the operation principle and experimental phenomena is developed. By the experimental results and the theoretical analyses based on the model, the validity of the m...
The nucleation of microdamage under dynamic loading was investigated through planar impact experiments accomplished with a light gas gun. The microscopic observation of recovered and sectioned specimens showed that microcracks were nucleated only by cracking of brittle particles inside material. However, for comparison the in situ static tensile tests on the same material conducted with a scanning electron microscope showed that the microcracks were nucleated by many forms those were fracture of ductile matrix, debonding particles from matrix and cracking of brittle particles. The quantitative metallographic observations of the specimens subjected to impact loading showed that most of the cracked particles were situated on grain boundaries of the aluminum matrix. These facts suggested the concept of critical size and incubation time of submicroscopic cavities in the dynamic case and the mechanism of ...
Abstract Therapeutic proteins are exposed to various potential contact surfaces, particles, and leachables during manufacturing, shipping, storage, and delivery. In this review, we present published examples of interfacial- or leachable-induced aggregation or particle formation, and discuss the mitigation strategies that were successfully utilized. Adsorption to interfaces or interactions with leachables and/or particles in some cases has been reported to cause protein aggregation or particle formation. Identification of the cause(s) of particle formation involving minute amounts of protein over extended periods of time can be challenging. Various formulation strategies such as addition of a nonionic surfactant (e.g., polysorbate) have been demonstrated to effectively mitigate adsorption-i...
High molecular weight products of the ozonolysis reaction of particle-phase 9-octadecenoic acid (oleic acid) have been studied by photoelectron resonance capture ionization (PERCI) mass spectrometry (MS). Oleic acid particles ( Formula Not Shown , Formula Not Shown ) were reacted with ozone (1.8x10-4atm) in a flow reactor at reaction times of 8 and 23s. Particles were sampled on-line with a differentially pumped particle inlet and chemically analyzed by PERCI-MS. PERCI is a soft ionization method that permits the direct measurement of relatively high molecular weight compounds, facilitating molecular identification. In addition to cyclic oxygenates, such as secondary ozonides and geminal diperoxides that were reported previously, we demonstrate the formation of polymers at the particle sur...
The production method of the elastic composite containing ferrous particles and titanium barium particles dispersed in the porous silicone matrix is described in this article. Since it contains ferrous and titanium barium particles, this composite shows magnetorheological and also electrorheological properties. The electrostriction of composite samples in the electric field with maximal intensity 1.5x10{sup 6} V/m was investigated. The magnetostriction in the magnetic field with maximal induction 1 T was also investigated. It was found that samples elongate with increased electric field intensity, and the magnetic field induction was detected. By increasing the samples' elongation with increase of ferrous particles, titanium barium particles and pores number were also detected. In the investigated division of the electric and magnetic field the elongation changed in a ...
A supercritical fluid-based method is proposed to produce coenzyme Q10 (CoQ10) nanoparticles. First, CoQ10/polyethylene glycol 6000 composite particles are prepared by a modified PGSS (particles from gas-saturated solutions) process with controlling the flow rate of the gas-saturated solution. Then, CoQ10 nanoparticles are obtained by dissolving the composite particles into water. The effect of experimental variables of the modified PGSS process, including pressure, temperature, flow rate of the gas-saturated solution, and mass fraction of CoQ10, on the CoQ10 particle size and particle size distribution was investigated. Results show that CoQ10 slurry product with a median diameter of 190nm and yield of 89.8% can be prepared at an optimum condition (operating pressure of 25MPa, operating t...
The atmospheric processing by ozone of peptide-containing mixed particles was investigated as proxies for biogenic and sea spray primary organic aerosol. Reactions were performed in a flow reactor and particle composition was monitored by photoelectron resonance capture ionization aerosol mass spectrometry. Mixed particles containing dipeptides in a saturated organic matrix of stearic and palmitic acids showed no reaction under ozonolysis at exposure levels of 2.5???10?4?atm s O3. However reactions of mixed particles of a dipeptide (Leu-Leu) in an unsaturated matrix (oleic acid) under the same conditions resulted in a rapid loss of the peptide ion signal, as well as the carrier matrix, and appearance of a number of ion signals corresponding to secondary products. High molecular weight imid...
Most active pharmaceutical ingredients (API) exhibit particle size distributions with some degrees of asymmetry deviating from log-normality. A new log-skew-normal (L-S-N) distribution model is proposed for a systematic comparison of the asymmetry effect on content uniformity. The new model originated from the S-N model used by Azzalini gives a close approximation to real API particle size distribution. Monte-Carlo method was employed to simulate the dosage potency distribution. A high risk of over potency is uncovered when either the dose is low or API particle size distribution is positively skewed. This is due to the formation of pseudo heavy tail in potency distribution that decays slower than exponentially. Nomographs of API particle size versus dosage strength were constructed with a...
Smoothed Particle Hydrodynamics (SPH) is a Lagrangian, particle-based method that is well suited to industrial mixing simulations. Mass transport is simply the motion of the particles, and its grid-free nature means that it can easily accommodate complicated geometries involving moving parts and sharp corners. This article describes 2D SPH simulations of a Twin Cam mixer and compares the results against experimental data and results from two published finite element method (FEM) simulations. To analyze the mixing processes in the Twin Cam mixer, we present a method for calculating the Finite-Time Lyapunov Exponent (FTLE) using SPH particle data. The FTLEs can be used to locate the unstable and stable manifolds in the flow and indicate where mixing is either promoted or inhibited in the flo...
The study of the {alpha}-particle energy distributions associated with ND and SD states in {sup 151,152}Dy has been carried out. The Dy isotopes were produced in the reaction {sup 37}Cl+{sup 123}Sb at 191 MeV via the ({alpha}5n) and ({alpha}4n) channels, respectively. In {sup 151}Dy the {alpha}-particle energy distributions associated to ND and SD are very different from each other, both at the low and high energy sides inducing a difference of 3 MeV in the {alpha}-particle mean energy. In {sup 152}Dy the situation is different; the {alpha}-particle spectral shapes are similar and a difference in the {alpha}-particle mean energy of only 0.7 MeV is deduced. A description in terms of energy localization of entry states is given. (orig.)
A new numerical technique called the convolution-based particle tracking (CBPT) method is developed to simulate resident or flux-averaged solute concentrations in groundwater models. The method is valid for steady-state flow and linear transport processes such as sorption with a linear sorption isotherm and first-order decay. The CBPT method uses particle tracking to take advantage of the ability of particle-based approaches to maintain sharp fronts for advection-dominated transport problems common in groundwater modeling and because of the flexibility of the random walk method to simulate a wide range of possible forms of the dispersion tensor. Furthermore, the algorithm for carrying out the convolution and superposition calculation from particle tracking results is very efficient. We sho...
FastSLAM is a framework for simultaneous localization using a Rao-Blackwellized particle filter. In FastSLAM, particle filter is used for the mobile robot pose (position and orientation) estimation, and an Extended Kalman Filter (EKF) is used for the feature location's estimation. However, FastSLAM degenerates over time. This degeneracy is due to the fact that a particle set estimating the pose of the robot loses its diversity. One of the main reasons for loosing particle diversity in FastSLAM is sample impoverishment. It occurs when likelihood lies in the tail of the proposal distribution. In this case, most of particle weights are insignificant. Another problem of FastSLAM relates to the design of an extended Kalman filter for landmark position's estimation. The performance of the EKF and the quality of the estimation depends heavily on correct a priori knowledge of the process ...
The high frequency, low mode number toroidicity-induced Alfven eigenmodes (TAE) are shown to be driven unstable by the circulating and/or trapped {alpha}-particles through the wave-particle resonances. Satisfying the resonance condition requires that the {alpha}-particle birth speed v{sub {alpha}} {ge} v{sub A}/2{vert bar}m-nq{vert bar}, where v{sub A} is the Alfven speed, m is the poloidal model number, and n is the toroidal mode number. To destabilize the TAE modes, the inverse Landau damping associated with the {alpha}-particle pressure gradient free energy must overcome the velocity space Landau damping due to both the {alpha}-particles and the core electrons and ions. The growth rate was studied analytically with a perturbative formula derived from the quadratic dispersion relation, and numerically with the aid of the NOVA-K code. Stability criteria in terms of the ...
Reductive quenching of two photoexcited ruthenium(II) complexes by an anionic electron donor, 2,2{prime}-azinobis(3-ethyl-benzothiazoline-6-sulfonate) (ABTS{sup 2{minus}}), in aqueous solution was examined by laser flash photolysis before and after adding positively charged colloidal (250-{angstrom} diameter) alumina-coated silica particles. The kinetics and quantum yields of electron transfer with an anionic sensitizer, RuL{sub 3}{sup 4{minus}} (L = bathophenanthroline disulfonate), and a cationic one, Ru(bpy){sub 3}{sup 2+} (bpy = 2,2{prime}-bipyridine), were compared. Coadsorption of ABTS{sup 2{minus}} and RuL{sub 3}{sup 4{minus}} by the particles greatly enhanced the rate of quenching such that only the reaction occurring on the surfaces of the particles was observed. Electron transfer from ABTS{sup 2{minus}} to RuL{sub 3}{sup 4-*} occurred by a static (nondiffusional) process, and the quenching efficiency was maximal ...
LiFePO{sub 4} cathode materials with distinct particle sizes were prepared by a planetary ball-milling method. The effects of particle size on the morphology, thermal stability and electrochemical performance of LiFePO{sub 4} cathode materials were investigated. The ball-milling method decreased particle size, thereby reducing the length of diffusion and improving the reversibility of the lithium ion intercalation/deintercalation. It is worth noting that the small particle sample prepared using malonic acid as a carbon source achieved a high capacity of 161 mAh g{sup -1} at a 0.1 C rate and had a very flat capacity curve during the early 50 cycles. However, the big particle samples ({proportional_to}400 nm) decayed more dramatically in capacity than the small particle size samples ({proportional_to}200 nm) at high current densities. The improvement in electrode ...
The magnetic separation technology using sub-microsized ferromagnetic particle is indispensable in many areas of medical biosciences. For example, ferromagnetic particles (200-500 nm) are widely used for cell sorting in stem cell research with the use of cell surface-specific antigens. Nanosized ferromagnetic particles (10-20 nm) have been suggested as more suitable in drug delivery studies given their efficiency of tissue penetration, however, the magnetic separation method for them has not been established. One of the major reasons is that magnetic force acting on the object particles decreases drastically as a particle diameter becomes small. In this study, magnetic force acting on the targets was enhanced by the combination of superconducting magnet and the filter consisting of ferromagnetic particle. By doing so, we confirmed that Fe{sub 3}O{sub 4} of 20 nm ...
The influence of location of airborne particle source, ventilation rate, air inlet size, supply air velocity, air outlet location, and heat source on the distributions of airborne particle concentration and draught risk in an operating room is investigated. The investigation is carried out by using a flow program with the k-[epsilon] model of turbulence. Based on a standard case, five cases, each with one changed parameter, are computed, and the detailed field distributions of air velocity, temperature, airborne particle concentration, and draught risk are presented. The parametric study concludes that, for a better air quality and thermal comfort, it is desirable to use a higher inflow rate, a larger inlet area, and a uniform velocity profile of supply air. Outlet location and heat source have little influence on the distributions of the particle concentration in the room. It has also been found that ...
The adsorption of mercury vapor on particles was studied by using soot particles generated by incineration of sewage sludge (EP-ash) and activated carbon particles. Through the experiments, it was found that, at 298 K, the EP-ash has a fairly high adsorption capacity for mercury vapor in the order of 10/sup -6/g/g, which is between that of the ordinary soils and that of activated carbon particles. Furthermore, it was found that physical adsorption of mercury vapor on the studied particles at high temperature is described by Dubinin's equation. On the basis of the equation, it was shown that EP-ash physically adsorbs very little mercury at high temperature, and therefore, most mercury in the EP-ash is chemically adsorbed or contained in a form of mercury compounds. Nevertheless, the total amount of mercury contained in the particles is very little ...
Experimental and theoretical investigation on drying of a single coal particle in fluidized bed combustor is presented. Coal particle drying was considered via the moist shrinking core mechanism. The results of the drying test runs of low-rank Serbian coals were used for experimental verification of the model. The temperature of the coal particle center was measured, assuming that drying was completed when the temperature equalled 100{sup o}C. The influence of different parameters (thermal conductivity and specific heat capacity of coal, fluidized bed temperature, moisture content and superheating of steam) on drying time and temperature profile within the coal particle was analyzed by a parametric analysis. The experimentally obtained results confirmed that the moist shrinking core mechanism can be applied for the mathematical description of a coal particle drying, while dependence ...
Testing of barrier properties of insulating materials against radon is usually based on the measurement of the radon diffusion coefficient. Presented report summarizes results of radon diffusion coefficients measurements in more than 120 insulating materials obtained throughout Europe. All measurements were performed by the Czech Technical University, Faculty of Civil Engineering in cooperation with the Radiation Protection Institute. We have found out that great differences exist in diffusion properties, because the diffusion coefficients vary within eight orders from 10"-"1"5 m"2/s to 10"-"8 m"2/s. For each material category of different chemical composition statistical evaluation of results is presented. Possibilities of usage of the radon diffusion coefficient for the design of radon resisting membranes are discussed. Based on the experience from the Czech Republic the paper is trying to show that controlling applicability of membranes by setting of the upper limit for the radon ...
The visible semiconductor laser includes an InAlGaP active region surrounded by one or more AlGaAs layers on each side, with carbon as the sole p-type dopant. Embodiments of the invention are provided as vertical-cavity surface-emitting lasers (VCSELs) and as edge-emitting lasers (EELs). One or more transition layers comprised of a substantially indium-free semiconductor alloy such as AlAsP, AlGaAsP, or the like may be provided between the InAlGaP active region and the AlGaAS DBR mirrors or confinement layers to improve carrier injection and device efficiency by reducing any band offsets. Visible VCSEL devices fabricated according to the invention with a one-wavelength-thick (1{lambda}) optical cavity operate continuous-wave (cw) with lasing output powers up to 8 mW, and a peak power conversion efficiency of up to 11%. 5 figs.
A scheme of evaluating a generalized three-photon excitation cross section sigma/sub (3)/ in neutral atomic argon at 3144.67 A is outlined. Three photons at this wavelength can excite the neutral argon atoms from the ground 3p/sup 6/ /sup 1/S/sub 0/ state to the 3p/sup 5/4s'(1/2)/sub 1//sup 0/ state. The fourth photon will ionize the argon atoms. Assuming linear polarization of the incident laser radiation, contributions from several channels in various energy-level schemes are summed in the evaluation of the transition probability. For a laser linewidth of ..delta..lambda/sub L/ = 1 A, our maximum numerical value of the computed result for the three-photon excitation cross section is sigma/sub (3)/ = 1.414 x 10/sup -80/ cm/sup 6/ s/sup 2/. .AE
We proposed that a new type of the electrostatic microwiggler with a wiggler period (0.1 mm {le}1{sub w}{le}1 mm) and the wiggler field strength (E{sub w}{le} 100 kV/m) can be produced on the surface of a PZT when a high power and high frequency ultrasonic wave travels through a PZT bar. Numerical simulations in the linear and nonlinear gain regime show that a weak microwiggler (E{sub w}100 kV/m,{lambda}{sub w}{approx}100 periods), operating in magnetoresonance with a strong guide field (B{sub o}{approx} 3.6T), can generate a millimeter and submillimeter radiations with medium electronic efficiency of few percents. It is shown that the maximum output power of the compact FEL using the wiggler system generated on the surface of the piezoelectric material may be upto a few Watts with a relatively low energy and low current electron beam (Ew {approx}100 keV and I{sub b}1 mA).
The RADionuclide Transport, Removal, And Dose (RAD-TRAD) code is designed for U.S. Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the off-site population and to control room operators following a design-basis accident at light water reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465. The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken, including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different removal mechanisms that use, as input, information about the conditions in the plant and predict either a removal ...
The RADionuclide Transport, Removal, And Dose (RADTRAD) code is designed for US Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the offsite population and to control room operators following a design-basis accident at Light Water Reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465, ``Accident Source Terms for Light-Water Nuclear Power Plants.`` The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different removal mechanisms that use, as input, information about the ...
The detailed electronic energy band structure of hexagonal close-packed #alpha#-zirconium, corresponding to the atomic configuration of 4d"25s"2 of its four outermost valence electrons, has been computed by the composite-wave variational version of the augmented-plane-wave(APW) method in conjunction with the X#alpha#(#alpha# = 0.70424) exchange approximation for obtaining the potentials. From these data the electronic density of states and its angular-momentum-decomposed components have been obtained by the Raubenheimer-Gilat method. These quantities are required in order to calculate the electron-phonon interaction parameter (lambda) and the superconducting transition temperature (Tsub(c)) within the framework of the theories of Gaspari and Gyorffy and McMillan. A study of the variation of Tsub(c) with the Coulomb pseudopotential (#mu#*) revealed that #mu#* = 0.1 yields the best agreement between theory and experiment for #alpha#-Zr. Also studied from the energy ...
The first-step formation constants of UO_2"2"+-complexes of some N-hydroxysuccinamic acids viz. N-phenyl N-hydroxysuccinamic acid (Rsub(p)H(sub(2))), N-o-toyl N-hydroxysuccinamic acid(Rsub(t)oHsub(2)) and N-m-tolyl N-hydroxysuccinamic acid (Rsub(t)mHsub(2)) have been determined spectrophotometrically. Stabilities are in the ligand order Risup(m)Hsub(2)>Rsub(t)oHsub(2)>Rsub(p)Hsub(2). The first-step hydrolysis constant k' of UO_2"2"+ ion has been determined spectrophotometrically and found to be pk'=4.00 at a constant ionic strength (#mu#=0.5) at 30deg-+0.5deg and the molar extinction coefficients of the species UO_2"2"+ and UO_2(OH)"+ at #LAMBDA#=385 nm are found to be 2.0 and 13.0 respectively. (author).
The structural and electronic properties of the A-15 compounds Nb{sub 3}Rh and Nb{sub 3}Ir were studied by means of escalar relativistic full-potential linearized augmented-plane wave (FP-LAPW) calculations with generalized gradient corrections. An investigation of the band structure of the hypothetical Nb{sub 3}Nb compound was also performed at the theoretical equilibrium lattice constant to ascertain the contribution of the nontransition elements on the B site in these A{sub 3}B-type compounds. Band structures and total densities of states were obtained. A rough estimate of the electron-phonon coupling parameter {lambda} as well as of the electronic specific-heat coefficient {gamma} were obtained for both Nb{sub 3}Rh and Nb{sub 3}Nb, which confirms that this latter is a low-temperature superconductor with T{sub c} - 10K.
We consider a general, neutral, dynamical model of biodiversity. Individuals have i.i.d. lifetime durations, which are not necessarily exponentially distributed, and each individual gives birth independently at constant rate \\lambda. We assume that types are clonally inherited. We consider two classes of speciation models in this setting. In the immigration model, new individuals of an entirely new species singly enter the population at constant rate \\mu (e.g., from the mainland into the island). In the mutation model, each individual independently experiences point mutations in its germ line, at constant rate \\theta. We are interested in the species abundance distribution, i.e., in the numbers, denoted I_n(k) in the immigration model and A_n(k) in the mutation model, of species represented by k individuals, k=1,2,...,n, when there are n individuals in the total population. In the immigration model, we prove that the numbers (I_t(k);k\\ge 1) of species ...
We report the results of a linearized augmented-plane-wave calculation of the electronic structure of fcc La at three lattice constants corresponding to ambient pressure, 50, and 120 kbars. The Kohn-Sham-Gaspar approximation for exchange and correlation is used and the potential is allowed a fully non-muffin-tin form. The f bands lie approx.2--2.5 eV above the Fermi level and are approx.1 eV wide, resulting in a very small (0.05 electrons) localized f occupation. Under pressure the f bands rise and broaden appreciably, resulting in only a slight increase in f occupation. The rigid-muffin-tin approximation for the electron-phonon interaction lambda overestimates the superconducting transition temperature T/sub c/ by 40%, but we find that the drastic increase in T/sub c/ under pressure can be attributed primarily to changes in the electronic stiffness eta. Structural transitions which occur at 25 and 53 kbars may be related to changes in Fermi-surface topology which ...
A number of amines can be employed for all volatile treatment (AVT) of steam generator (SG) systems of nuclear power reactors. These amines form complexes with Cu{sup 2+} and Ni{sup 2+} ions which come into water due to corrosion. The redox reactions of a number of Cu(II)-AVT amine complexes and the stability of the transient species formed have been studied by pulse radiolysis technique. Rate constants for the reaction of e{sub aq}{sup -} with a number of Cu(II)-amine complexes have been determined by following the decay of e{sub aq}{sup -} absorption. Stability of Cu(I)-amine complexes was studied by following the kinetics of the bleaching signal formed at the {lambda}{sub max} of the Cu(II) amine complex. Except for Cu(I)-triethanolamine complex all other Cu(I)-amine complexes were found to be stable. One-electron oxidation of Cu(II) amine complexes was studied using azidyl radicals for the oxidation reaction as OH radicals react with the alcohol groups present ...
In this paper the authors present the first emitter efficiency results for the thin film 40 percent Er-1.5 percent Ho YAG (Yttrium Aluminum Garnet, Y3Al5O12) and 25 percent Ho YAG selective emitter at 1500 K with a platinum substrate. Spectral emittance and emissive power measurements were made (1.2 less than lambda less than 3.2 microns). Emitter efficiency and power density are significantly improved with the addition of multiple rare earth dopants. Predicted efficiency results are presented for an optimized (equal power density in the Er, (4)I[sub 15/2]-(4)I[sub 13/2] at 1.5 microns, and Ho, (5)I[sub 7]-(5)I[sub 8] at 2.0 micron emission bands) Er-Ho YAG thin film selective emitter.
Color formation in aqueous solutions of the ditetrazolium salt blue tetrazolium (BT{sup 2+}) in the absence or presence of oxygen is a complex radiation chemical reaction. The final stable product is the poorly soluble diformazan violet to blue pigment having a broad spectral absorption band ({lambda}{sub max}=552 nm). The reaction of BT{sup 2+} with the hydrated electron proceeds by rapid reduction of BT{sup 2+} followed by protonation at the nitrogen closest to the unsubstituted phenyl group, via the two intermediate tetrazolinyl radicals shared by the ditetrazole ring nitrogens. The effect of solution pH, N{sub 2}O saturation, and the presence of the reducing agent dextrose are examined. The system serves as a radiochromic sensor and a dosimeter of ionizing radiations. Solutions of 5 mmol l{sup -1} BT{sup 2+} at pH 7.3 serve as dosimeters over an absorbed-dose range of approximately 0.2-6 kGy (dearated, with a range of 1-8 mmol l{sup -1} dextrose) and of about ...
The transients involved in the reaction of tetracycline (TC) with reducing radicals such as e{sub aq}{sup -}, (CH{sub 3}){sub 2}COH and CO{sub 2}{sup .-}have been characterized by the pulse radiolysis technique. The semi-reduced species formed ({lambda}{sub max} = 630 nm, {epsilon} 3.4 x 10{sup 3} dm{sup 3} mol{sup -1} cm{sup -1}) has been found to be a strong reductant with reduction potential lying in the range -0.450 to -1.40 V vs NHE. TC reacts with e{sub aq}{sup -} at diffusion-controlled rates and the rate constant, depending upon the ionic form of TC existing at a particular pH, varies from 1.2 x 10{sup 10} to 2.8 x 10{sup 10} dm{sup 3} mol{sup -1} s{sup -1}. Based on these results a plausible site of electron addition has been suggested. Reaction of H atoms with TC gives rise to a transient which exhibits spectral and kinetic features different from that of semi-reduced species. (author).
The development and evaluation of a post-column reaction detector sensitive to platinum(II) complexes is presented in which sodium bisulfite is used as the derivatizing agent with potassium dichromate as an activating agent. The influences of mobile phase changes (i.e., pH, organic modifiers, electrolytes), oxygen, metal ions, and order of reagent addition on reaction kinetics and product yield are defined and used in optimization of detector response. Detection at lambda/sub max/ 290 nm results in an on-line post-column sensitivity of 40-60 ng/mL for selected cis-dichloroplatinum complexes and a sensitivity of 300-1200 ng/mL for four (substituted)-malonato-platinum complexes. The reaction detector is used to monitor the kinetics of aquation of cisplatin (CDDP) and to quantitate CDDP degradation in plasma. As the sensitivity for CDDP in plasma is comparable to that achieved from high pressure liquid chromatography (HPLC) effluent fractionation/off-line flameless ...
Room temperature continuous wave operation of red ([lambda][sub 0] [approximately] 660 nm) vertical cavity surface emitting laser arrays is reported. The 1 [times] 64 arrays have a pitch of 100 [mu]m with device diameters of 15 [mu]m with device diameters of 15 [mu]m. Grown by metalorganic vapor phase epitaxy, the devices consist of an AlGaInP strained quantum well optical cavity active region surrounded by AlGaAs distributed Bragg reflectors (DBR's). The top coupling DBR includes a partial dielectric stack, deposited after implanted device fabrication. All 64 devices operation simultaneously with peak output powers >0.45 mW, threshold current <1.5 mA, and threshold voltages [<=] 2.7 V. The differential quantum efficiencies exceed 10%.
Using the advantage that the projected range of ions in matter is sharply limited, a new technique for the production of three-dimensional microstructures has been developed. Based on the P-LIGA technique (Proton-Lithographie, Galvanoformung, Abformung) this process allows the generation of structures with surfaces of almost any shape having a root mean square roughness of about #lambda#/50 for visible light wavelengths. An ion beam with diameters between 2 and 50 #mu#m is directly writing the structures and the shape is varied by geometrical manipulation of the sample in three axes during the exposure. Practically, structures have been written using protons with an energy of 1.8 MeV in a provisional experimental setup with beam diameters of 10 and 50 #mu#m, respectively. After irradiation, the parts exposed were dissolved in a liquid developer without affecting the nonirradiated parts. The shape and the rms roughness of the resulting structures were estimated by ...
We present new theoretical predictions for the galaxy three-point correlation function (3PCF) using high-resolution dissipationless cosmological simulations of a flat {Lambda}CDM Universe which resolve galaxy-size halos and subhalos. We create realistic mock galaxy catalogs by assigning luminosities and colors to dark matter halos and subhalos, and we measure the reduced 3PCF as a function of luminosity and color in both real and redshift space. As galaxy luminosity and color are varied, we find small differences in the amplitude and shape dependence of the reduced 3PCF, at a level qualitatively consistent with recent measurements from the SDSS and 2dFGRS. We confirm that discrepancies between previous 3PCF measurements can be explained in part by differences in binning choices. We explore the degree to which a simple local bias model can fit the simulated 3PCF. The agreement between the model predictions and galaxy 3PCF measurements lends further credence to the ...
We report the growth and fabrication of midwave infrared InAs/GaSb strain layer superlattice (SLS) detectors. Growth of alternate interfaces leads to a reduced strain between the GaSb buffer and SLS ({delta}a{sub parallel}/a=-5x10{sup -4}), enabling the growth of active regions up to 3 {mu}m (625 periods). The structural, optical, and electrical properties of the active region were characterized using x-ray crystallography and photoluminescence, respectively. p-i-n detectors were grown using 625 periods of 8 ML (monolayer) InAs/8 ML GaSb as the active region. The {lambda}{sub cutoff} for the detectors was 4.6 {mu}m with a conversion efficiency of 32% at V{sub b}=-0.2 V. Detectivity was obtained using noise power spectral density measurements under 300 K 2{pi} field of view illumination and was equal to 5.2x10{sup 10} and 3x10{sup 10} cm Hz{sup 1/2}/W (V{sub b}=-0.02 V, T=80 K) in the white noise and 1/f noise limit (at 50 Hz)
We describe a new concept for a MEMS-based active spatial filter for astronomical spectroscopy. The goal of this device is to allow the use of a diffraction-limited spectrometer on a seeing limited observation at improved throughput over a comparable seeing-limited spectrometer, thus reducing the size and cost of the spectrometer by a factor proportional to r0/D (For the case of a 10 meter telescope this size reduction will be approximately a factor of 25 to 50). We use a fiber-based integral field unit (IFU) that incorporates an active MEMS mirror array to feed an astronomical spectrograph. A fast camera is used in parallel to sense speckle images at a spatial resolution of lambda/D and at a temporal frequency greater than that of atmospheric fluctuations. The MEMS mirror-array is used as an active shutter to feed speckle images above a preset intensity threshold to the spectrometer, thereby increasing the signal-to-noise ratio (SNR) of the spectrogram. ...
Nanocrystalline ZnO films were fabricated via a simple method involving the oxidation of Zn films at a remarkably low temperature of 380 C. X-ray diffraction study confirmed that the Zn films were completely oxidized even at the low temperature of 380 C and the ZnO films fabricated were of polycrystalline wurtzite structure. Room temperature optical pumping using a frequency-quintupled Q-switched Nd:YAG laser ({lambda}=213 nm) exhibited that sharp peaks at around 3.12 eV emerged above excitation powers of {proportional_to}7 MW/cm{sup 2}, demonstrating lasing in the ZnO films. These results represent that the process is a simple, promising approach for fabricating ZnO of sufficient optical performance for use as ultraviolet (UV) light emitters and an alternative UV laser source; both are key components in short-wavelength photonic devices. (orig.)
Using Zgamma candidate events collected by the CDF detector at the Tevatron Collider, we search for potential anomalous (non-standard-model) couplings between the Z boson and the photon. At the hard scatter energies typical of the Tevatron, standard model Zgamma couplings are too weak to be detected by current experiments; hence any evidence of couplings indicates new physics. Measurements are performed using data corresponding to an integrated luminosity of 4.9 /fb in the Z -> nunubar decay channel and 5.1 /fb in the Z -> l^+l^- (l=mu, e) decay channels. The combination of these measurements provides the most stringent limits to date on Zgamma trilinear gauge couplings. Using an energy scale of Lambda = 1.5 TeV to allow for a direct comparison with previous measurements, we find limits on the CP-conserving parameters that describe Zgamma couplings to be |h_3^{\\gamma,Z}| < 0.017 and |h_4^{\\gamma,Z}| < 0.0006. These results are consistent with standard ...
A modified epitaxial design leads to straightforward implementation of short (1{lambda}) optical cavities and the use of C as the sole {ital p}-type dopant in AlGaInP/AlGaAs red vertical-cavity surface-emitting lasers (VCSELs). Red VCSELs fabricated into simple etched air posts operate continuous wave at room temperature at wavelengths between 670 and 690 nm, with a peak output power as high as 2.4 mW at 690 nm, threshold voltage of 2.2 V, and peak wallplug efficiency of 9%. These values are all significant improvements over previous results achieved in the same geometry with an extended optical cavity epitaxial design. The improved performance is due primarily to reduced optical losses and improved current constriction and dopant stability. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.
A high power AlGaInP single quantum well graded index separate confinement heterostructure. It comprises a substrate and a multiplicity of layers deposited thereon comprising a single Ga{sub x}In{sub x}P quantum well where x has a value from about 0.4 to about 0.6; multiple graded index regions on both sides of the quantum well and cladding layers adjacent to each graded region of the well, the graded region comprising Al{sub y}(Ga{sub 1{minus}y}){sub 0.5}In{sub 0.5}P quaternary alloy; wherein the value of y in the graded region varies from about 0.2 at the quantum well/graded region interface to up to about 0.6 for the cladding layers/graded index regions; the heterostructure having a low broad area threshold current with pulsed thresholds in the range from about 1 to about 2 Amps/cm{sup 2} and a differential efficiency of from about 20 to about 60 percent.
Radio, optical and X-rays telescopes are improving our knowledge of deep space. All these telescopes detect electromagnetic radiation at various frequencies. But a different kind of radiation is generated in the deeper space; it is the gravitational one. Gravitational waves change the space-time metric. As a consequence, GW telescopes should detect an extremely small strain (h < 10/sup -21/) of the geometry of a reference frame; if the frame has a reference dimension (L) of some kilometers, the deformation amplitude ( Delta L = h * L) is limited to 10/sup -16/ meters. Laser interferometers are the most suitable devices to make precise measurements of distances. Their resolution is limited by the laser wavelength ( lambda = 10/sup -6/ meters) and by the light wave-shift detection capability ( Delta Phi = 1 ppb). These theoretical limits are strongly degraded by different noise sources, which reduce the actual resolution by several orders of magnitude. Applied ...
Anti-proton and positron Galactic cosmic ray (GCR) spectra are among the key targets for indirect detection of dark matter (DM). The boost factors, corresponding to an enhancement of the signal|linked to the clumpiness properties of the dark matter distribution|, have been taken as high as thousands in the past. The dramatic impact of these boost factors for indirect detection of antiparticles, for instance with the PAMELA satellite or the coming AMS-02 experiment, asks for their detailed calculation. We take into account the state-of-the-art results of high resolution N-body dark matter simulations to calculate the most likely energy dependent boost factors|linked to the GCR propagation properties|, for anti-protons and positrons. The results from extreme, but still possible, configurations of the clumpy dark matter component is also discussed. Starting from the mass and space distributions of sub-halos, the anti-proton and positron propagators are used to calculate the mean value and ...
A new spectrofluorimetric method was developed for the determination of trace amount of nicotinamide adenine dinucleotide phosphate (NADP). Using europium (Eu{sup 3+})-tetracycline (TC) complex as a fluorescent probe, in the buffer solution of pH 7.60. NADP can remarkably enhance the fluorescence intensity of the Eu{sup 3+}-TC complex at {lambda} = 612 nm and the enhanced fluorescence intensity of Eu{sup 3+} ion is in proportion to the concentration of NADP. Optimum conditions for the determination of NADP were also investigated. The dynamic range for the determination of NADP is 4.4 x 10{sup -7} to 2.2 x 10{sup -6} mol l{sup -1} with detection limit of 6.9 x 10{sup -8} mol l{sup -1}. This method is simple, practical and relatively free interference from coexisting substances and can be successfully applied to determination of NADP in synthetic water samples and in serum samples. Moreover, the enhancement mechanisms of the fluorescence intensity in the Eu{sup ...
The dosimetric characteristics for a new brachytherapy seed source (I-Plant"T"M model 3600) were measured using LiF thermoluminescent dosimeters and appropriate phantom materials in conformance with the methodology and guidance provided by the AAPM Task Group 43. The I-Plant"T"M model 3600 is the successor to the I-Plant"T"M model 3500. The major difference between these sources is that the model 3600 contains a leaded-glass core to provide radio-opacity (while the model 3500 contains a silver core), which does not produce spectral contamination upon neutron activation. The dose rate constant #LAMBDA# for the model 3600 was determined to be 1.00 Gy h"-"1 U"-"1 (with a 6% overall relative standard deviation), compared to 1.01 cGy h"-"1 U"-"1 reported for the model 3500 in previous studies. The remaining dosimetric characteristics also are similar for both sources.
III--V based devices such as field effect transistors, heterojunction bipolar transistors, and lasers often have surface leakage and thermal degradation problems due to surface states which pin the Fermi level to the midgap. Sulfur based passivation processes are known to improve device performance by altering surface-state densities. We have developed a voltage-controlled anodic sulfur passivation scheme using Na[sub 2]S dissolved in ethylene glycol. Our process has repeatedly produced a [similar to]25% improvement in peak output power near the catastrophic damage limit in visible ([lambda]=670 nm) AlGaInP edge-emitting lasers. The threshold current density before and after passivation, and the [ital I]--[ital V] characteristics before and after catastrophic failure, were essentially unchanged indicating that passivation raises the threshold for facet damage.
III--V based devices such as field effect transistors, heterojunction bipolar transistors, and lasers often have surface leakage and thermal degradation problems due to surface states which pin the Fermi level to the midgap. Sulfur based passivation processes are known to improve device performance by altering surface-state densities. We have developed a voltage-controlled anodic sulfur passivation scheme using Na_2S dissolved in ethylene glycol. Our process has repeatedly produced a #approx#25% improvement in peak output power near the catastrophic damage limit in visible (#lambda#=670 nm) AlGaInP edge-emitting lasers. The threshold current density before and after passivation, and the I--V characteristics before and after catastrophic failure, were essentially unchanged indicating that passivation raises the threshold for facet damage.
Single crystals of semi-organic L-histidine hydrobromide have been grown by slow evaporation technique from a mixture of L-histidine and hydrobromic acid in aqueous solution at ambient temperature. From high-resolution X-ray diffraction analysis, the crystalline perfection of the grown crystal has been studied. Single crystal X-ray diffraction analyses, Nuclear Magnetic Resonance spectral analysis, Thermo-Gravimetry (TG), Differential Thermal Analysis (DTA) and hardness test have been employed to characterize the as-grown crystals. The UV cutoff wavelength of the grown crystal is below 300 nm and has a wide transparency window, which is suitable for second harmonic generation of laser in the blue region. Nonlinear optical characteristics have been studied using Q switched Nd:YAG laser (#lambda#=1064 nm). The second harmonic generation conversion efficiency of the grown crystals confirms their suitability for frequency conversion applications.
We report a simple method for the label-free detection of double-stranded DNA using surface-enhanced Raman scattering (SERS). We prepared cetyltrimethylammonium bromide (CTAB)-capped silver nanoparticles and a DNA-nanoparticle complex by adding silver nanoparticles to {lambda}-DNA solutions. In the present study, the utilization of CTAB-capped silver nanoparticles facilitates the electrostatic interaction between DNA molecules and silver nanoparticles; at the same time, the introduction of DNA avoids adding aggregating agent for the formation of nanoparticle aggregates to obtain large enhancement of DNA, because the DNA acts as both the probe molecules and aggregating agent of Ag nanoparticles. Atomic force microscopy (AFM) studies show that the morphology of DNA-Ag nanoparticle complexes seems to be determined by the concentrations of the DNA and the nanoparticles. Surface-enhanced Raman scattering (SERS) studies show that the morphology of the complexes plays a ...
Novel hybrid organic/inorganic nanocomposites made of metal oxide and conjugated polymer nanocomposite and its application in bulk-heterojunction solar cells were studied. The composite was composed of different concentrations of strontium titanate (SrTiO_3) and polyaniline doped phosphoric acid. The optimum concentration of strontium titanate was found to be 0.2 v/v. An inorganic-organic photovoltaic device with a structure of Ag/Pani-H_3PO_4-SrTiO_3/Al has been fabricated. The ideality factor value of the diode was found to be 1.8. This n value of the diode implies a deviation from ideal junction behaviour. The barrier height #phi#_b value for the diode was found to be 0.56 eV. The Ag/Pani-H_3PO_4-SrTiO_3/Al diode shows a photovoltaic behaviour with a maximum open-circuit voltage V_o_c of 2.49 V, and short-circuit current I_s_c of 5.6 mA under light illumination #lambda# = 460 nm. The conversion efficiency was found to be 5.2%. It is evaluated that the ...
Exhaust fine and ultra fine particle numbers, particle sizes, mass, shape, structure and density were studied from Euro II - EEV emission level heavy-duty vehicles. For total particle emission factors city buses were run on dynamic conditions simulating city bus driving. The new heavy-duty chassis dynamometer of VTT was used. Vehicles were a comprehensive sample of current city bus fleet, the type approved emission level of which was Euro II - Euro III. Also cleaner engines of Euro IV to EEV targeted emission level were included: CRT, CNG, DPF. Particle emissions of these buses were extremely low; numbers 1/100 - 1/1000 and masses 1/10 - 1/100 of those of the predominating techniques. Morphological properties of fine particle populations that represent majority of particle size distribution (Da < 500 nm) are being analyzed by image processing (Matlab) ...
Anthropogenic sulfate aerosol, together with particles from biomass burning, may significantly reduce the climatic warming due to man-made greenhouse gases. The radiative forcing of aerosol particles is based on their ability to scatter and absorb solar radiation (direct effect), and on their influences on cloud albedos and lifetimes (indirect effect). The direct aerosol effect depends strongly on the size, number and chemical composition of particles, being greatest for particles of 0.1-1 {mu}m in diameter. The indirect aerosol effect is dictated by the number of particles being able to act as cloud condensation nuclei (CCN). For sulfate particles, the minimum CCN size in tropospheric clouds is of the order of 0.05-0.2 {mu}m. To improve aerosol parameterizations in future climate models, it is required that (1) both primary and secondary sources of various ...
Complete energy spectra and angular distributions of the light charged particles (A < or = 4) were measured for the bombardment of "2"7Al, "5"8Ni, "9"0Zr, "2"0"9Bi, and "2"3"2Th with 140 MeV #alpha# particles. The spectral shapes of a given emitted particle are very similar for all target nuclei except in the region of the evaporation peak. The slopes of the energy spectra in the forward direction become steeper as the mass of the observed particle decreases and vary very rapidly with angles. The experimental data can be characterized by compound nuclear evaporation processes at low energies, or at backward angles, and by direct reactions, nonequilibrium components and projectile breakup processes at high energies and forward angles. The breakup cross section for #alpha# particles is found to be appreciable. The total yield of light charged particles is ...
The buckling test program comprised 37 axially loaded cylinders made of austenitic stainless steels and 6 reference cylinders made of mild steel. The three test parameters were the steel grade, the shell slenderness and the operating temperature. The chosen steel grades are typical for practical applications: AISI 304 (No. 1.4301) as the basic austenitic stainless steel, AISI 316 L (No. 1.4404) as a molybdenum alloyed and AISI 316 Ti (No. 1.4571) as a molybdenum and titanium alloyed austenitic stainless steel. The chosen shell slendernesses are typical for the above-mentioned elastic-plastic region: r/t=50, 150 and 400, approximately corresponding to non-dimensional slenderness parameters {lambda}=0.3, 0.5 and 0.9 respectively. The chosen testing temperatures cover a wide range of applications: T=20 C, 100 C, 250 C and 400 C. The test cylinders were manufactured from 3.0 mm, 1.0 mm and 0.5 mm steel sheets, cold rolled into the cylindrical shape and longitudianlly ...
We consider the case of a test sphere (ball) of radius a{sub 1} rotating at constant angular velocity {omega} in an otherwise quiescent unbounded suspension of uniformly sized spheres of radii a{sub 2} dispersed in a Newtonian fluid of viscosity {mu}. To the first order in the volume fraction c of suspended spheres it is shown that when the ball is small compared with the suspended spheres the suspension does not behave as regards the hydrodynamic torque L exerted on the ball like a homogeneous Newtonian fluid characterized by the usual Einstein viscosity coefficient {mu}{sub s}={mu}(1+5/2c). Explicitly, the torque on the rotating sphere does not obey Kirchoff{close_quote}s law, L=8{pi}{mu}{sub s}a{sub 1}{sup 3}{omega} for no slip. Rather, a modified form of Kirchoff{close_quote}s law is obtained in which the Einstein coefficient of 5/2 is multiplied by a coefficient which is less than unity in magnitude and is functionally dependent only upon the suspended-sphere/test-sphere size ...
To make the surface composites with hard ceramics particles is an effective means for satisfying the request for the wear-resistance of the casting products. Covering casting is a general method for forming the composites by adding the adhesive into ceramics particles. However, due to the using of adhesive, pore and intermediate are easy to generate, and it is one of the reasons making the wear-resistance unstable. In the present study, it is attempted to form the wear-resistant composite layer by dispersing cast tungsten carbide (CTC) particles on the surface of wear-resistant 7 mass% Mn steel without using adhesives. Subsequently, the experiments on the wear-resistance of the obtained surface composites under several wear conditions are carried out. It is revealed by the results thereof that 7 mass% Mn steel surface composites with CTC particles have the wear-resistance which is even more excellent ...
An automated Time Resolved Aerosol Collector (TRAC) has been developed for sequential sampling of field-collected aerosols for laboratory-based Computer Controlled Scanning Electron Microscopy/Energy Dispersed X-ray (CCSEM/EDX) single particle analysis. The collector is optimized for use of grid-supported 20 nm carbon films as deposition substrates. The carbon films have low enough X-ray background to permit EDX analysis down to 0.1-0.2 ?m particles, including detection of low-Z elements: C, N, & O. The TRAC provides unattended sampling onto a set of 151 individual grids, at sequential time intervals as short as 1 min. After collection, the samples are sealed and refrigerated pending analysis. The utility of the TRAC-CCSEM/EDX approach is exemplified using the aerosol samples collected during the Texas 2000 Air Quality Studies (Aug. 15 ? Sept. 15, 2000). We are able to quantitatively follow the time evolution in the relative contribution of ...
In this paper, we investigated the effect of alcohol solvents (ethanol, n-propanol, and n-butanol) and isomeric alcohol solvents (iso-propanol, iso--butanol, and tert-butanol). In addition, we observed the effect of the mixed alcohol solvents on the particle formation as using a mixture od ethanol and butanol at a ratio od 30/70, 50/50 and 70/30 vol %, respectively. In case of ethanol solvent, particle size of silica showed the smallest and the narrowest size distribution among the various solvent. On the contrary, for the n-butanol solvent, largest broad distribution of particle size was observed. For the synthesis of particles having better spherical morphology and less agglomeration, alcohol solvent having no branches was considered appropriate. When mixed alcohol solvents were used, large silica particles with narrow size distribution were obtained, regardless of the ratio. 8 ...
A process and apparatus for solidifying radioactive waste liquid containing dissolved and/or suspended solids is disclosed. The process includes chemically treating for pH adjustement and precipitation of solids, concentrating solids with a thin-film evaporator to provide liquid concentrate containing about 50% solids, and drying the concentrate with heated mixing apparatus. The heated mixing apparatus includes a heated wall and working means for shearing dried concentrate from internal surfaces and subdividing dry concentrate into dry, powdery particles. The working means includes a rotor and helical means for positively advancing the concentrate and resulting dry particles from inlet to outlet of the mixing apparatus. The dry particles may also be encapsulated in a matrix material. Entrained particles in the vapor stream from the evaporator and mixer are removed in an integral ...
In order to investigate pitting corrosion of copper coiled tubes for air conditioning systems with an open heat storage water tank, the effect of carbon films on the inner surface of copper tubes and fine corrosion-product particles in water as environmental corrosion factor on pitting corrosion was studied by field test under real environmental conditions. As a result, pitting corrosion of copper tubes was caused by synergistic effect of fine corrosion-product particles in water and carbon films. Generation of pitting corrosion was derived from deposition of the films and particles, while considerable growth of pitting corrosion was dependent on the particles. Time variation of spontaneous electrode potential also showed the effect of the film and particle. Pitting corrosion potential was estimated to be nearly 100mV vs. SCE. The following measures against pitting corrosion were ...
In the present work the hydrogen desorption properties of nanostructured magnesium hydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM) of elemental Mg powder under hydrogen are investigated. A profound effect of the particle size of synthesized MgH2 hydride on its hydrogen desorption characteristics measured by differential scanning calorimetery (DSC) has been found. All synthesized MgH2 powders are characterized by a double hydrogen desorption peak. Furthermore, below a certain threshold particle size the DSC desorption temperature of the peak doublet starts decreasing rapidly with decreasing of the mean hydride powder particle size (expressed as equivalent circle diameter-ECD). In contrast, the nanograin (crystallite) size of MgH2 does not seem to have apparent effect on the DSC desorption temperature. It is also observed that for powder particles smaller than some threshold ...
An attempt to classify experimental data and to present new approach for the problem of cumulative production of particles and high-transverse momentum particles (#pi#"#+-#, k"#+-#, p, p-bar, d) on Li"6, Be, Mg, Si, "5"4","5"6","5"8Fe, "5"8","6"1","6"4Ni, Cu, "6"4Zn, "1"1"2","1"1"8","1"2"4Sn, "1"4"4","1"5"4Sm, "1"8"2","1"8"6W, U nuclei is made in the review. Particle cumulative production, quark-parton structure function, A dependence of particle production on nuclei and in nuclear collisions and A dependence of inclusive cross sections of particle cumulative production are discussed. Reactions with dissociation on nucleons of deuteron, helium and compound nuclei are considered. Possibility of unified description of different processes is discussed in terms of nucleus flucton model. 35 refs.; 22 figs.
Obtained experimental data on integral cross sections (ICS) of inelastic scattering of 50.5 MeV #alpha# particles with the excitation of "6","7Li, "9Be, "1"2","1"3C, "1"4C, "1"4N, "2"0Ne, "2"4Mg, "2"8Si nucleus low-lying energy levels are discussed. Regularities, detected in the behaviour of ICS forward scattering for 20-90 deg angles and backscattering for 90-160 deg angles for the target-nucleus under investigation are considered. Effect of reaction open channel number on #alpha#-particle scattering ICS where n,p,d- and #alpha#-channels were considered as the main channels for all the target-nuclei, is discussed. Dependence of #alpha#-particle scattering ICS on the target-nucleus level excitation energy and dependences of reaction open channel number on the channel spin, calculated for 50.5 MeV #alpha# particles and different target nuclei are shown in the diagrams. It is noted that the observed ...
The interrelationship between the testing temperature and HfC strength increment of an arc-melted W-3.6Re-0.4HfC was determined from 1950 K to 2980 K in a vacuum of better than 1.3{times}10{sup {minus}5} Pa (10{sup {minus}7} torr). The present research was focused on the characteristic temperature at which the rapid coarsening of HfC particles occurred and the effect of the second-phase particle size on the high temperature strength properties of this material. It was found that the HfC particle strengthening was effective in a W-Re matrix up to a characteristic temperature of 2450 K in the short-term tensile test. Carbon was found to be the rate-limiting solute in the HfC particle growth. The strength of HfC strengthened alloy at temperature above 0.5 T{sub m} is proportional to the square root of particle volume fraction. The yield strengths of W-3.6Re-0.26HfC calculated based on ...
The interrelationship between the testing temperature and HfC strength increment of an arc-melted W-3.6Re-0.4HfC was determined from 1950 K to 2980 K in a vacuum of better than 1.3x10"-"5 Pa (10"-"7 torr). The present research was focused on the characteristic temperature at which the rapid coarsening of HfC particles occurred and the effect of the second-phase particle size on the high temperature strength properties of this material. It was found that the HfC particle strengthening was effective in a W-Re matrix up to a characteristic temperature of 2450 K in the short-term tensile test. Carbon was found to be the rate-limiting solute in the HfC particle growth. The strength of HfC strengthened alloy at temperature above 0.5 T_m is proportional to the square root of particle volume fraction. The yield strengths of W-3.6Re-0.26HfC calculated based on the ...
The formation and growth of silicon-nanoparticles from silane in a microwave reactor was investigated. Experiments were performed for the following conditions: precursor concentration 380-2530 ppm, pressures of 20-30 mbar, microwave powers 120-300 W. The formed particles were examined in-situ with a particle mass spectrometer. Additionally, particles were collected on grids and analyzed by transmission electron microscopy, X-ray diffraction, and by determining the specific surface area by BET. The particle size was found to be in the range of 5-8 nm in diameter. A simple model was used to simulate the particle formation processes taking place inside the reactor. The microwave energy coupled into the reactor flow was treated as a spatially distributed energy source resulting in a local temperature increase. The particles were assumed to have a monodisperse size ...
In this study, Cu{sub 2}O/Cu composite particles were synthesized using an innovative chemical reduction method without any template and surfactant. X-ray diffraction (XRD) analysis revealed that the product mainly consisted of Cu{sub 2}O phase coexisting with a Cu phase. FE-SEM images showed that the octahedral shaped particles were Cu{sub 2}O. The electrochemical performance of the Cu{sub 2}O/Cu particles was investigated with regards to the working electrode material in alkaline solution. The particles had a maximum discharge capacity of 222.9 mAh/g at a discharge current density of 60 mA/g and a high value of 109.1 mAh/g after 50 charge-discharge cycles. Cyclic voltammetry revealed that the reaction between Cu{sub 2}O and Cu is the major electrochemical reaction during the charging and discharging process. Electrochemical impedance spectroscopy revealed that the formation of Cu{sub 2}O on the ...
The deposit of radioactive corrosion products in the cooling systems of nuclear reactors becomes a serious problem for the personnel of facilities. Crud has an important role in the process of depositing radioactive corrosion products. The main components of crud are hematite, magnetite, nickel ferrite and so on, and the particles of these oxide compounds are distributed in water. Most of the behavior of crud are still not known. As for the mechanism of the production of crud, the Potter-Mann model has been proposed. However, the precipitation process of iron ions in water is unknown. The crud is defined as the particles filtered by 0.45 micrometer millipore filters. However, it is not known whether there are crud particles smaller than this size. The crud particles can be adsorbed on the filters by the surface electrochemical interaction. The adsorption of cations to crud particles ...
Whenever moving surfaces interact, wear particles are produced. Microscopic examination of the morphology of such wear debris is an accepted method for machine condition monitoring and fault diagnosis. Wear particle analysis has not, however, been widely accepted in industry because it is dependent on expert interpretation of particle morphology and relies on subjective assessment criteria. Consequently, the methods are time consuming and expensive and are not always consistent. The use of automated computer image analysis systems to assess the morphology of debris promises to overcome these limitations by making the methods more time and cost efficient, and also more consistent and effective. The first step required for automation of the analysis procedure is to develop objective criteria for assessing the wear particle morphology. Numerical parameters to describe the morphology have been developed and ...
Methods for estimating particle number may be based on at least three different principles. Two of them, isolation of particles and indirect counting, have been predominant until recently. The new methods based on section pairs (disectors) are unbiased and far more efficient. The three principles and their historical developments are described, emphasizing that the newly developed principles have old roots, which were forgotten until recently. It is concluded, that 'learned societies' combined with individual enthusiasm are material for the spread and development of new ideas.
The Bragg Curve Spectrometer (BCS) is an ionization chamber long enough to stop particles of interest. Particles enter through the cathode window and leave an ionization track parallel to the electric field. The ionization electrons drift through a Frisch grid and are collected on an anode. The anode current, as a function of time, is split and used as input for two amplifiers, one with a long integration time constant for energy measurement, and one with a short time constant to pick off the maximum ionization or Bragg peak. The Bragg peak, which is proportional to the nuclear charge, is used for particle identification. We have constructed and tested several versions of the BCS. The results are described.
The Bragg Curve Spectrometer (BCS) is an ionization chamber long enough to stop particles of interest. Particles enter through the cathode window and leave an ionization track parallel to the electric field. The ionization electrons drift through a Frisch grid and are collected on an anode. The anode current, as a function of time, is split and used as input for two amplifiers, one with a long integration time constant for energy measurement, and one with a short time constant to pick off the maximum ionization or Bragg peak. The Bragg peak, which is proportional to the nuclear charge, is used for particle identification. We have constructed and tested several versions of the BCS. The results are described.
The diffusion coefficient of particles in radioactive gases has been calculated with account of random wandering of aerosols (occurrence of local fields affecting the particles; recoils accompanying radiation emitted by particles, etc.). To determine the diffusion coefficient, the method of Fokker-Planck equation derivation was used. A formula is presented for calculating the radiation-stimulated diffusion coefficient. A linear growth of the diffusion coefficient with radioactivity is noted according to the formula, the diffusion coefficient is mainly determined by the field in the radiation damage region. The aerosol radioactivity may result in a more rapid deposition of aerosols in the pipelines and aerosol purification systems. The diffusion rate grows not only in the presence of intrinsic radioactivity but in case of external radiation exposure as well.
Natural rubber latexes were vulcanized by ..gamma..-rays with two polyfunctional monomers, neopentylglycol diacrylate (A-NPG) and dimethacrylate (NPG). In comparison with A-NPG, NPG was more soluble in rubber particles, but it was less effective as an accelerating agent for the vulcanization because of the smaller rate of polymerization. On the other hand, the colloidal stability of the latex containing A-NPG was low because it was localized on the surface of rubber particles due to its poor solubility to the particles. The solubility of A-NPG was improved by adding A-NPG with solvents. The maximum tensile strength of the irradiated latex film was 350 kg/cm/sup 2/ at 3 Mrad.
Natural rubber latexes were vulcanized by #gamma#-rays with two polyfunctional monomers, neopentylglycol diacrylate (A-NPG) and dimethacrylate (NPG). In comparison with A-NPG, NPG was more soluble in rubber particles, but it was less effective as an accelerating agent for the vulcanization because of the smaller rate of polymerization. On the other hand, the colloidal stability of the latex containing A-NPG was low because it was localized on the surface of rubber particles due to its poor solubility to the particles. The solubility of A-NPG was improved by adding A-NPG with solvents. The maximum tensile strength of the irradiated latex film was 350 kg/cm"2 at 3 Mrad. (author).
Quark models of production of cumulative particles and the EMC effect are analyzed. It is shown that all these models are characterized by a universal relation between the spectrum of cumulative nucleons and the cross section for cumulative particles containing valence quarks of the nucleus. This relation is tested for the deuteron, and the role of secondary nuclear processes for heavy nuclei is discussed. It is noted that the ''sea'' cumulative particles (K/sup -/, p-bar) are particularly important for understanding the nature of the difference between the structure functions of a nucleus and of a free nucleon.
Energy levels in N=50 nuclei are calculated allowing single-particle excitations from the p{sub 1/2} and g{sub 9/2} shells into the d{sub 5/2}, s{sub 1/2}, d{sub 3/2}, and g{sub 7/2} shells. Important parts of the interaction are determined by least-squares fits to known levels. Agreement with experiment is very good. The high-spin particle-hole states appear to be mainly yrast levels in mass 93 and higher, but are not in {sup 90}Zr. {copyright} {ital 1997} {ital The American Physical Society}
Using U-120 cyclotron in the course of correlation experiment one studied mechanisms of excitation and decay of "1"2C nucleus states resulting from irradiation of deuterium-polyethylene target by 27.2 MeV energy #alpha#-particle beam via recording of #alpha#-#alpha#-coincidence simultaneously with investigations of #alpha# + d-interactions. Production of "1"2C excited states decaying with the escape of #alpha#-particle and "8Be nucleus in the ground and the excited states is the basic mechanism of the studied #alpha# + "1"2C interaction
Due to the low thermal conductivity of ceramics large temperature gradients are present through the powder particles during plasma spray deposition. As a result the particles often impinge at the substrate in a semi-molten form; which in turn substantially affects the final characteristics of the coating being formed. This study is dedicated to the novel modelling development and simulation of a semi-molten droplet impingement. The study examines the impingement process during impact, spreading and solidification of semi-molten zirconia. The simulation provides an insight to the heat transfer process during impact and solidification of a semi-molten powder particle and illustrates the freezing-induced break-up mechanism at the splat periphery.
A new scheme to accurately retain kinetic electron effects in particle-in-cell (PIC) simulations for the case of electrostatic drift waves is presented. The splitting scheme, which is based on exact separation between adiabatic and on adiabatic electron responses, is shown to yield more accurate linear growth rates than the standard df scheme. The linear and nonlinear elliptic problems that arise in the splitting scheme are solved using a multi-grid solver. The multi-grid particle-in-cell approach offers an attractive path, both from the physics and numerical points of view, to simulate kinetic electron dynamics in global toroidal plasmas.
It is proved the mathematical theorem, that the wave function describes the statistical ensemble of particles, but not a single particle. Supposition, that the wave function describes a single particle appears to be incompatible with formalism of quantum mechanics. One discusses the reasons, why this very simple statement has not been proved mathematically for many years. The reason lies in application of the trial and error methods for construction of the quantum mechanics. Application of this method as the main tool of investigation during eighty years generated "fitting mentality" of all microwold researchers.
Conduction-band electrons, formed by pulse radiolysis of Degussa P25 TiO_2 particles, have been monitored by time-resolved microwave conductivity and found to undergo equilibrium localization and eventual recombination at the particle surface. In the presence of isopropyl alcohol recombination is retarded due to surface hole scavenging. The particle bulk can then be pumped with mobile electrons, which survive for seconds.
The charge distribution in the alpha particle induced fission of "2"0"9Bi has been studied at alpha particle energy of 55.7 MeV and 58.6 MeV. The fractional cumulative yields of "9"7Zr, "9"9Mo, "1"0"1Mo and "1"1"2Pd have been determined using gamma ray spectrometry. The charge distribution have been found to be broad. (author). 4 refs., 1 ta b.
In several recent papers on entanglement in relativistic quantum systems and relativistic Bell's inequalities, relativistic Bell-type two-particle states have been constructed in analogy to nonrelativistic states. These constructions do not have the form suggested by relativistic invariance of the dynamics. Two relativistic formulations of Bell-type states are shown for massive particles, one using the standard Wigner spin basis and one using the helicity basis. The construction hinges on the use of Clebsch-Gordan coefficients of the Poincare group to reduce the direct product of two unitary irreducible representations (UIRs) into a direct sum of UIRs.
Borrelia burgdorferi sensu lato genospecies were differentiated by PCR-based sequencing of the borrelial flagellin gene. To evaluate the usefulness of KingFisher"T"M magnetic particle processor in PCR product purification, borrelia PCR products were purified with KingFisher"T"M magnetic particle processor prior to cycle sequencing and the quality of the sequence data received was analyzed. KingFisher was found to offer a rapid and reliable alternative for borrelial PCR product purification.
The possibilities, advantages, and difficulties of determining nuclear matter densities by elastic scattering of alpha-particles are generally discussed. On the basis of particular experimental data - 104 MeV alpha-particle scattering from "4"0,"4"2,"4"4,"4"8Ca - a refined folded potential is introduced using a density-dependent alpha-nucleon-interaction and target nucleus densities described by Fourier-Bessel-series. Thereby, the total nucleon densities of these isotopes were determined with little model dependence. The resulting root-mean-square radii and density differences are compared with other experimental results obtained by different methods. (orig.).
This paper presents an analysis of the performance of a selective emitter using small particles of rare earth compounds stable at high temperatures in a low emittance inert gas stream. An expression for the spectral emissive power excluding radiation scattering was derived to include the radiation in the emission band, produced by electronic transitions of the rare earth ion, and the continuum radiation outside the emission band produced by the rare earth host. Preliminary results suggest that a selective emitter based on suspended rare earth oxide particles will have high efficiency and merits further experimental investigation. {copyright} {ital 1996 American Institute of Physics.}
The immune system modulates many key biological processes in humans. However, the exact role of the immune system in particle-associated periprosthetic osteolysis is controversial. Human tissue retrieval studies, in vivo and in vitro experiments suggest that the immune response to polymer particles is non-specific and macrophage-mediated. Lymphocytes may modulate this response. However direct lymphocyte activation by polymer particle-protein complexes seems unlikely. However, metallic byproducts may complex with serum proteins and lead to a Type IV, lymphocyte-mediated immune reaction. In predisposed individuals, this reaction may rarely lead to persistent painful joint effusions, necessitating debridement and excision of the bearing surfaces of the prosthesis. In these patients, retrieved...
May 11, 2011 ... The Particle Environment Monitor (PEM) on NASA's Upper Atmosphere Research Satellite (UARS) measures the type, amount, energy, and ...
We have fabricated nanometer-spaced electrodes on electron-transparent silicon nitride membranes. A thin Cr/Au layer is evaporated on the backside of the membrane which serves as a gate electrode. Using these devices, we have performed three-terminal electron transport measurements on gold nano-particles at liquid helium temperature. Coulomb Blockade features have been observed and the capacitance to the gate has been extracted. After transport measurements, the Cr/Au back gate is removed and the devices are inspected with a transmission-electron microscope (TEM). TEM inspection reveals the presence of a few nano-particles in the nanogap, which is in agreement with the transport measurements. In addition, the nano-particle size as observed by TEM coincides with the one estimated from the gate capacitance value.
A method is described for determining the particulate contamination in miniature ball bearings in which the bearing is flushed with a solvent that is then filtered. The particles that are collected on the filter are examined by optical microscopy.
We present results on searches for exotic particles (relativistic magnetic monopoles and WIMPs) and for UHE neutrinos, obtained with the Baikal neutrino telescope NT200.
... water content according to the hydrometeor type. ... the documentation and the movement personnel and ... Dyer, RM, 1970: Particle fall speeds within ...
Applications of cutting-edge estimation techniques, such as, but not limited to, sigma-point and particle filters, to spaceflight navigation problems. ...
LiNi{sub 0.8}Co{sub 0.2}O{sub 2} particles from high-power lithium-ion cells were examined to determine material changes that result from accelerated aging tests. X-ray absorption spectroscopy (XAS) and transmission electron microscope (TEM) data indicated a Li{sub x}Ni{sub 1-x}O-type layer on the particle surfaces. The greater thickness on particles from high-power fade cells indicate that these surface layers are a significant contributor to cathode impedance rise observed during cell tests.
Over the last few years it has become increasingly clear that low energy, but high precision experiments provide a powerful and complementary window to physics beyond the Standard Model. In this note we illuminate this by using minicharged particles as an example. We argue that minicharged particles arise naturally in extensions of the Standard Model. Compatibility with charge quantization arguments suggests that minicharged particles typically arise together with a massless hidden sector U(1) gauge field. We present several low energy experiments employing strong lasers, electric and magnetic fields that can be used to search for (light) minicharged particles and their accompanying U(1) gauge boson.
Canada will provide telescope baffles and fine error sensor assemblies. ..... ( Ongoing) Flight tests aboard sounding rockets and balloon planned for FY 1995. .... the effects of incoming energetic particles and solar radiation on the ...
An experimental investigation on the thermal decomposition of CH4 into C and H2 was carried out using a 5kW particle-flow solar chemical reactor tested in a solar furnace in the 1300-1600K range. The reactor features a continuous flow of CH4 laden with mm-sized carbon black particles, confined to a cavity receiver and directly exposed to concentrated solar irradiation of up to 1720 suns. The reactor performance was examined for varying operational parameters, namely the solar power input, seed particle volume fraction, gas volume flow rate, and CH4 molar concentration. Methane conversion and hydrogen yield exceeding 95% were obtained at residence times of less than 2.0s. A solar-to-chemical energy conversion efficiency of 16% was experimentally reached, and a maximum value of 31% was numer...
Over the last several years considerable concern has been expressed regarding the potential detrimental effects of radon and radon progeny on our health. The complex nature of the radon decay scheme, which involves the emission of a variety of radiations including several [alpha] particles, [beta] particles, and [gamma]-rays, does not lend itself to clear delineation of the biological effects of the [alpha] particles alone. Polonium-210, the terminal radionuclide of the radon decay series, is useful for this purpose because it has a relatively long shelf-life ([tau][sub 1/2] = 138 d), and it only emits a single 5.3 MeV [alpha] particle in its decay to stable [sup 206]Pb. Accordingly, it has been used extensively in radiobiological studies with incorporated radionuclides. The radionuclide [sup 210]Po is produced in a reactor from [sup 209]Bi. (Author).
Reactions of reducing species from acetonitrile media with silver iodide particles (#approx#25-angstrom diameter) have been investigated by pulse radiolysis techniques. Injection of electrons into these ultrasmall particles leads to transient bleaching of the adsorption of AgI at wavelengths close to the onset of absorption (#approx#400 nm) with the concomitant reduction of AgI to metallic silver. The reduction of Ag"+ ions and formation of silver atoms and/or dimeric Ag_2 molecules on three different size AgI particles (#approx#100, 35, and #approx#25 angstrom) have also been examined by picosecond laser spectroscopy.
The properties of individual radioactive particles present in a sample, such as a swipe, are more interesting than bulk properties of the sample. The present work focuses on instrumentation that provides position-sensitive spectral information non-destructively from the sample. The experimental part of the work was realized using a device called PANDA (Particles And Non-Destructive Analysis). The detector setup used in the study contains a broad-energy HPGe gamma-ray detector and a position-sensitive alpha detector. Both detectors are connected to a time-stamping event-mode data acquisition system. The method is shown to locate particles with sub-millimetre accuracy and distinguish the interesting particles from non-interesting ones. (author)
Experimental data on high energy cumulative particle production are analyzed in the frame of flucton models. The performed analysis evidence for the flucton as a multiquark system with high baryon dnsity.
The transport of magnetospheric particles in the outer cusp region is examined by means of three-dimensional single particle codes. It is shown that, at high altitudes, particles can experience nonadiabatic motions leading to significant magnetic moment changes. It is demonstrated that this nonadiabatic behavior can be interpreted, at least partly, by the action of an impulsive centrifugal force perturbing the particle gyromotion. Systematic trajectory calculations reveal that plasma sheet ions which ExB convert toward the magnetopause from low L-shells in the dayside sector are subjected to such nonadiabatic motions. As a result of magnetic moment damping, a number of them are injected into the loss cone and subsequently precipitate near the cusp equatorward edge.
The possibility of controlling the radial electric field of toroidal plasmas by injecting high energy electrons along the reversible loss cone orbit of the helical magnetic traps is investigated. It is well known that the radial electric field plays an important role in the confinement improvement scenario especially in the low collisional regime under the physics picture of neoclassical theory. For this purpose, it is made clear that the most suitable particles are transit particles, which show a transition from helically trapped orbits to blocked ones. It is also found that a parallel AC electric field launched from outside assists this transition and makes it possible for particles to penetrate deeply into the plasma. In addition we clarify that the viscosity of the plasma coupled with the helical field configuration provide a bifurcation of plasma states and its stable solution results in confinement improvement. ...
Photoelectron resonance capture ionization (PERCI) is a soft and sensitive ionization method, based on the attachment of low-energy (<1 eV) photoelectrons to organic analyte molecules. PERCI has been developed in our laboratory for the real-time analysis of organic particles by mass spectrometry, and is employed here to monitor the heterogeneous reaction of ozone with oleic acid. Simplified identification of the reaction products is possible as a result of the soft nature of PERCI, giving predominantly the [M--H](-) ions. The major particle-phase products are identified as: 1-nonanal, nonanoic acid, 9-oxononanoic acid, and azelaic acid, consistent with proposed mechanisms. New insight into this well-studied heterogeneous reaction is gained as additional minor particle-phase products, consistent with the Criegee mechanism, are readily detected. PMID:15468105
SUMMARY We construct a new class of granular landslide models in which avalanches are simulated with large numbers of independent particles moving under the influence of topographically derived gravitational and centripetal acceleration. Concurrently, the particles suffer deceleration due to basal and dynamic friction. The novel aspect of the calculation is that complex particle-to-particle interactions, fluctuating basal contacts, and unresolved topographic roughness within and below the deforming flow are mimicked by random perturbations in along-track and cross-slope acceleration. We apply the method to the 1980 May 18 Mount Saint Helens debris avalanche by constraining the initial geometry and structure of the slide mass from geological data, and the initial failure sequence from eyewi...
the revealed stage of T Tauri star evolution, is only a mere shadow of its former self. Once primary accretion starts, one has the (poorly quantified) ...
A time-of-flight (TOF) spectrometer has been constructed at the JAERI 20 MV tandem accelerator facility. A position-sensitive start detector, which consists of a thin carbon foil, microchannel plates and a resistive plate, was developed for the TOF measurements through the spectrometer. The time and position resolutions obtained were 120 ps and 0.3 mm for ..cap alpha.. particles from /sup 241/Am, respectively. A two-dimensional position-sensitive detector was also developed to measure the solid angle of the spectrometer and the maximum solid angle obtained was 9.5 msr. As a particle detector a Bragg curve ionization chamber was developed. From the Bragg curves of heavy ions in the detector, energies, ranges and Bragg curve peaks were measured and used for particle identification. The resolving power Z/..delta..Z of the atomic number was about 50.
TiH{sub 2} and TiD{sub 2} thick targets were bombarded with 100 to 200 keV protons. Evidence for nuclear reactions was obtained by means of a surface barrier particle detector. Proton irradiation of TiD{sub 2} produced the following observations: {alpha} particle emission identified as (p, {alpha}) reactions from {sup 11}B and {sup 7}Li impurities in the target at ppm concentrations; and {approx}3 MeV proton and {approx}1 MeV triton emission from secondary D-D reactions caused by elastic scattering of the primary proton with a target deuteron. A 3.9 MeV {alpha} particle peak measured by others was not observed. (author)
The effects of fine-particle C, such as diesel soot, on the optical properties of urban haze in the visible wavelength range were explored to determine the dominant effects and to see if simple parameters (such as visual range in green) provide an adequate measure of these effects. It is known that fine-particle C absorbs more strongly in the blue than in the red, so that when it is mixed with a white pigment, the resulting gray can appear somewhat brown. The possibility of a similar effect in urban hazes was investigated, but found not to occur. When the sun is overhead, the near-horizon sky chromaticities caused by mixtures of fine-particle C and non-absorbing aerosol can also be produced by non-absorbing aerosols alone. It is shown that absorbing aerosol will darken the horizon sky, and a simple equation for the radiance of the horizon sky is derived. The effect of absorbing aerosol on the distance at which white and ...
One-step synthesis of Pt-loaded carbon nanoparticles including single-wall carbon nanohorns (SWNHs) by arc plasma in liquid nitrogen was demonstrated using Pt-contained graphite anode. The size distribution of Pt particles can be controlled by adjusting the concentration of Pt in the graphite anode. In the observation by transmission electron microscope, the diameter of less than 5 nm of Pt particles were observed as approximately 90% among the Pt particles when Pt was contained in the anode at 1.3 at.%. When Pt concentration in the anode was decreased to 0.4 at.%, the percentage of Pt particles whose diameter is less than 5 nm decreased to approximately 60%. It was verified that the as-grown Pt-loaded products produced by this method can be useful for the power generation by polymer electrolyte fuel cell.
... being pulled out of water, the movement is restricted ... This heating depended on the particle size ... hydrometeor injection into the upper tropopause. ...
The optical and nonlinear optical properties of colloidal solutions of silver obtained by laser ablation in water and ethanol are studied. It is shown that freshly prepared colloids experience a full or partial sedimentation by changing their nonlinear optical properties. Aqueous colloids undergo a partial sedimentation and their nonlinear optical absorption changes to nonlinear optical transmission. The obtained results are interpreted using the Drude model for metal particles taking the particle size into account and can be explained by the sedimentation of larger silver particles accompanied by the formation of a stable colloid containing silver nanoparticles with a tentatively silver oxide shell. The characteristic size of particles forming such a stable colloid is determined and its optical nonlinearity is estimated.
We have developed a simulation code with the techniques which enhance both spatial and time resolution of the PM method for which the spatial resolution is restricted by the spacing of structured mesh. The adaptive mesh refinement (AMR) technique subdivides the cells which satisfy the refinement criterion recursively. The hierarchical meshes are maintained by the special data structure and are modified in accordance with the change of particle distribution. In general, as the resolution of the simulation increases, its time step must be shortened and more computational time is required to complete the simulation. Since the AMR enhances the spatial resolution locally, we reduce the time step locally also, instead of shortening it globally. For this purpose we used a technique of hierarchical time steps (HTS) which changes the time step, from particle to particle, depending on the size of the cell in which ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy transfer, is investigated. This technique is shown to offer a large potential benefit. ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy transfer, is investigated. This technique is shown to offer a large potential benefit. ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. An initial analytic study was done by Fisch and Rax. Here the authors calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favorable for wave amplification from alpha energy. They find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy transfer, is investigated. ...
Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)
The heat transfer augmentation effect by the unsteady heat conduction between the particles and heat transfer surface is one of the main factors, causing the heat transfer augmentation around the stagnation point in the gas-solid two-phase impinging jet flow. By separating and evaluating that effect, material influence on it was studied of particles and heat transfer surface, together with change by the jet flow condition. That effect enlarged with enlarging in heat capacity, multiplied by the heat conduction coefficient, of both the particles and heat transfer surface, and if both of them were constant in material combination, was dominated by the contact frequency of particles per unit time. Therefore in case of lading solid particles, equal in weight, that effect enlarges with diminishing in particle diameter. Such a heat transfer augmentation mechanism model ...
Several heat transfer augmentation mechanisms contribute to the heat transfer augmentation around the stagnation point in the gas-solid two-phase impinging jet flow. Among those contributions, that of heat exchange was numerically analyzed and characteristically elucidated by the unsteady direct contact heat conduction at the time of impingement between the laden particles and heat transfer surface. In other words, if the contact time is short between the particles and heat transfer surface, the former is heated by heat stored in the latter as a heat capacity. In such a region, the heat quantity to be transferred to the particles changes by not only the thermal property value (heat capacity multiplied by heat conduction coefficient) of particles but also that of heat transfer surface. Then by using several kinds of particles and heat transfer surface, different in thermal property ...
This article addresses the need for new data on indirect effects of natural and anthropogenic aerosol particles on atmospheric ice clouds. Simultaneous measurements of the concentration and composition...Full Text Available
Many nondestructive beam position monitors are known. However, these devices can not be used for DC particle beam diagnostics. We investigated a method of beam diagnostics applicable for the operative control of DC high power e-beam inside closed waveguide. A design of the detector for determination of{open_quote} center of mass {close_quote} position of DC particle beam was developed. It was shown that the monitor can be used as a nondestructive method for the beam position control in resonators. Magnetic field of the particle beam outside a resonator is used. The detector consists of the steel yokes and magnetic field sensors. The sensors measure magnetic fluxes in the steel yokes fixed outside the resonator. When the particle beam changes its position, these magnetic fluxes also change. Beam displacement sensitivity of the monitor depends on the steel yoke dimensions. The detector sensitivity is ...
The emission of #alpha# particles in coincidence with the most deeply inelastic heavy-ion reactions has been studied for "1"8"1Ta + "1"6"5Ho at 1354 MeV laboratory energy and /sup nat/Ag + "8"4Kr at 664 MeV. #alpha# particle energy spectra and angular distributions, in coincidence with a projectile-like fragment, were acquired both in the reaction plane and out of the reaction plane at a fixed in-plane angle. The in-plane data for both systems are employed to show that the bulk of the #alpha# particles in coincidence with the deep-inelastic exit channel can be explained by evaporation from the fully accelerated fragments. Average velocity diagrams, #alpha#-particle energy spectra as a function of angle in several rest frames, and #alpha#-particle angular distributions are presented. The out-of-plane #alpha# particle angular distributions and the #gamma#-ray ...
Aug. 24, 1965. L. V. BALDWIN ETAL. 3202915. PARTICLE BEAM MEASUREMENT APPARATUS USING BEAM KINETIC. ENERGY TO CHANGE TIIE HEAT SENSITIVE RESISTANCE OF ...
'Improvement in understanding of the deposition of ambient dust particles on ECAM (Environmental Continuous Air Monitor) filters, reduction of the alpha-particle interference of radon progeny and other radioactive aerosols in different particle size ranges on filters, and development of ECAM''s with increased sensitivity under dusty outdoor conditions. As of May 1, 1998 (1/2 year into the project) the research-prototype 30-cm pulsed ionization chamber (PIC) is assembled and operational with an alpha particle energy resolution of better than 45 keV for 5-MeV alpha particles. Measurements of spectral resolution for alpha particles from radon decay products have been made as a function of filter type and dust loading conditions. So far, a study of ten filter types has found that the best combination of resolution and throughput is ...
These notes present a pedagogical introduction to magnetic monopoles, supersymmetry and dualities in gauge theories. They are based on lectures given at the X Jorge Andre Swieca Summer School on Particles and Fields. (author)
In the Introduction the history of the cascade probabilistic method development is described. The calculation model for different charged particles cascade probabilistic functions (CPF) was considered. A new analytical expressions for CPF for electrons, protons, alpha-particles and ions are obtained as well. A new results on mathematical analysis, algorithms, and calculation of CPF with taking into account charged particles energy losses on computer are cited. The peculiarities of these functions are analyzed. The detail analysis of these function behavior in relation from flying particles energy, target atomic number, generation and registration depth, and interactions number is carried out. The program packages in the Windows medium is developed on the visual programming languages: Visual Basic 6.0, Delphi 6.0, C++ Builder 6.0.
Dark Matter annihilation (DMA) may yield an excess of gamma rays and antimatter particles, like antiprotons and positrons, above the background from cosmic ray interactions. The excess of diffuse Galactic Gamma Rays from EGRET shows all the features expected from DMA. The new precise measurements of the antiproton and positron fractions from PAMELA are compared with the EGRET excess. It is shown that the charged particles are strongly dependent on the propagation model used. The usual propagation models with isotropic propagation models are incompatible with the recently observed convection in our Galaxy. Convection leads to an order of magnitude uncertainty in the yield of charged particles from DMA, since even a rather small convection will let drift the charged particles in the halo to outer space. It is shown that such anisotropic propagation models including convection prefer a contribution from ...
Nano-sized silica is a promising material for disease diagnosis, cosmetics and drugs. For the successful application of nano-sized material in bioscience, evaluation of nano-sized material toxicity is important. We previously found that nano-sized silica particles with a diameter of 70nm showed acute liver failure in mice. Here, we performed histological analysis of major organs such as the liver, spleen, lung, kidney, brain and heart in mice, chronically injected with 70-nm silica particles for 4weeks. Histological analysis revealed hepatic microgranulation and splenic megakaryocyte accumulation in these 70-nm silica particles treated mice, while the kidney, lung, brain and heart remained unaffected. Thus, liver and spleen appear to be the major target organs for toxicity by the chronic a...
... laws between particles (modeling UGV/UAV/UUV collectives) to ... A mobile robot test-bed is used in ... of this work on mobile robots executing pursuit ...
A new fuel-cell electrocatalyst based on highly porous carbonized polyacrylonitrile (PAN) microcellular foam with platinum particles was prepared recently in this laboratory. Its surface morphology, one of the most important aspects of a practical electrocatalyst, has been examined in terms of fractal theory and methods. The fractal dimension of the platinum particles dispersed in porous carbonized PAN foam was determined by using chronometric and rotating-disk-electrode methods in oxygen-saturated solutions. A fractal dimension smaller than 2 was obtained, which was attributed to the partially active nature of the surface of this electrocatalytic material. This value of fractal dimension is also proposed to be considered as a reaction dimension. A reaction dimension smaller than 2 may indicate that not all of the platinum particle surface is accessible to the incoming oxygen molecules.
Possible mechanisms of the cumulative production of particles in the processes of high momentum transfers to complex systems are discussed. Production of the multi-nucleon systems, the so-called fluctons, during collision of a high-energy particle with a nucleus, is proposed as a most realistic explanation of the cumulative effect. A probability of the flucton production in nucleus and its interaction with the incident particle are investigated. A possible origin of fluctons, considered, in the framework of the quark bag model, as quasistable states with the definite coupling energy and the lifetime, is studied. A probability for the presence of a flucton, as multibaryon configuration in a nucleus is evaluated. The production of multibaryon configurations in a nucleus is demonstrated to show up as a presence of strong multiparticle repulsion at small distances, which cannot be reduced only to ...
Flame propagating through zirconium particle cloud in a small-scale vertical rectangle chamber was investigated experimentally. In the experiments, the zirconium quoted 99% purity was used and the diameter of particles was distributed 1?22 ?m. The zirconium dust was dispersed into the chamber by air flow and ignited by an electrode spark. A high-speed video camera was used to record the images of the propagating flame. Micro-thermocouples, schlieren optical system and microscopic lens were used to obtain temperature profiles and flame structure, respectively. Based on the experimental results, flame propagation characteristics and flame structure of zirconium particle cloud were analyzed. The propagation velocity of the flame is quite slow in the initial 14 ms and then accelerates to maxim...
... A second hydrometeor sampler (MRI Model 1220 ... The cloud particle probe normally installed in ... to the northeast showed no significant movement. ...
We consider the Pauli theorem on the spin-statistics connection for faster-than-light particles. As the consequence of the unlocalizability of tachyons in space we conclude that their spin-statistics correlations are inverted.
Solid particle erosion (SPE) testing was made on Sandvik CRC 262 with different heat treatments and on the steels Type 321 and 15Mo3. The Studsvik Erofuge, a centrifugal erosion tester, was used and the testing was performed in air at room temperature. Alumina and olivine sand particles were used at a particle velocity of 60 m/s and at impingement angles of 60 degrees and 90 degrees. Differences in erosion resistance were obtained for CRC 262 depending on the heat treatment. Olivine sand resulted in lower erosion of CRC 262 than when using alumina. The particle type dependence is low for the other materials, Tp 321 and 15Mo3. CRC 262 has a slightly higher erosion resistance than Tp 321 and 15Mo3 and the differences are most pronounced when using olivine sand
dust measured in the Arabian Gulf region during UAE2 and examine the hypothesis that ... [8] UAE2 took place in the southern Arabian Gulf region in August and ...
According to empirical observations, some pattern formation phenomena in driven many-particle systems are more pronounced in the presence of a certain noise level. We investigate this phenomenon of fluctuation-driven ordering with a cellular automaton model of interactive motion in space and find an optimal noise strength, while order breaks down at high(er) fluctuation levels. Additionally, we discuss the phenomenon of noise- and drift-induced self-organization in systems that would show disorder in the absence of fluctuations. In the future, related studies may have applications to the control of many-particle systems such as the efficient separation of particles. The rather general formulation of our model in the spirit of game theory may allow to shed some light on several different kinds of noise-induced ordering phenomena observed in physical, chemical, biological, and socio-economic systems (e.g., attractive and ...
Nov 5, 2010 ... PEM. The Particle Environment Monitor measures the type, amount, energy, ... info, Daily PEM HEPS and MEPS data at the original sensor ...
The burning characteristics of fuel droplets containing nano and micron-sized aluminum particles were investigated. Particle size, surfactant concentration, and the type of base fluid were varied. In general, nanosuspensions can last much longer than micron suspensions, and ethanol-based fuels were found to achieve much better suspension than n-decane-based fuels. Five distinctive stages (preheating and ignition, classical combustion, microexplosion, surfactant flame, and aluminum droplet flame) were identified for an n-decane/nano-Al droplet, while only the first three stages occurred for an n-decane/micron-Al droplet. For the same solid loading rate and surfactant concentration, the disruption and microexplosion behavior of the micron suspension occurred later with much stronger intensity. The intense droplet fragmentation was accompanied by shell rupture, which caused a massive explosion of particles, and most of them ...
A new method of plasma treatment for powder particles was investigated. A glass bottle horizontally held on a rotating system was used for the treatment. The outside of the bottle was covered by the grounded metal net, and the rod electrode was provided at the center of the bottle, which was connected to an ac high voltage source. Powder particles were placed in the bottle with stainless steel beads of large diameter and the plasma was generated between two electrodes and while the bottle was rotating. Using this system, powder particles were uniformly plasma-treated without coagulation. After 40 seconds treatment with plasma of 0.55 W in Ar gas, the charge to mass ratio for polyethylene powder particles having 160 {mu}m mean diameter generated by stainless before treatment. (author)
The next generation of particle accelerator is currently being designed at CERN. An understanding of the market forces in the computer industry will play a crucial role in the success of the project.
Studies were conducted in northern Bohemia to simultaneously evaluate personal exposures to air pollution in the form of respirable particles containing polycyclic aromatic hydrocarbons (PAHs) and biomarkers...Full Text Available
A brief review of standard big bang nucleosynthesis theory and the related observations of the light element isotopes is presented. Implications of BBN on chemical evolution and constraints on particle properties will also be discussed.
The cyclic voltammetry indicated that the oxygen reduction reaction (ORR) proceeded by the four-electron pathway mechanism on larger Ag particles (174 nm), and that the ORR proceeded by the four-electron pathway and the two-electron pathway mechanisms on finer Ag particles (4.1 nm), simultaneously. The kinetics towards ORR was measured at a rotating disk electrode (RDE) with Ag/C electrode. The number of exchanged electrons for the ORR was found to be close to four on larger Ag particles (174 nm) and close to three on finer Ag particles (4.1 nm). The zinc-air battery with Ag/C catalysts (25.9 nm) was fabricated and examined. (author)
We investigate the profound relation between the equations of biological evolution and quantum mechanics by writing a biologically inspired equation for the stochastic dynamics of an ensemble of particles. Interesting behavior is observed which is related to a new type of stochastic quantization. We find that the probability distribution of the ensemble of particles can be decomposed into eigenfunctions associated to a discrete spectrum of eigenvalues. In absence of interactions between the particles, the out-of-equilibrium dynamics asymptotically relaxes towards the fundamental state. This phenomenon can be related with the Fisher theorem in biology. On the contrary, in presence of scattering processes the evolution reaches a steady state in which the distribution of the ensemble of particles is characterized by a Bose-Einstein statistics. In order to show a concrete example of this stochastic ...
We have mapped and studied the effects of MeV alpha-particle bombardment in polyvinylidene chloride (PVDC) and polyethylene (PE). We used 3.5 and 5.0 MeV alpha-particle incident beams and stacked polymer films to separate the contributing effects of the electronic ({var_epsilon}{sub e}) and nuclear ({var_epsilon}{sub n}) stopping powers. The electrical conductance and change in the chemical structures were measured by direct resistivity measurement, Raman microprobe, RBS and FTIR. The results indicate significant differences in the ({var_epsilon}{sub e}) and ({var_epsilon}{sub n}) effects at higher alpha-particle bombardment fluences. {copyright} {ital 1997 American Institute of Physics.}
We consider particle evaporation and fission of an ensemble of hot, rotating compound nuclei as a stochastic process. We derive a set of coupled differential equations formed by a Fokker-Planck equation describing fission, and master equations for calculating particle evaporation. From these equations, we are able to determine multiplicities of prefission neutrons, protons and {alpha}-particles, their energy spectra and their angular momentum distributions. A comparison of our results with experimental data provides us with information regarding the reduced friction coefficient {beta}, the fission barrier height and the level density parameter. For different iridium isotopes, ({sup 181,185,187}Ir), {sup 185}Os and {sup 158}Er, we obtain as an upper limit {beta}{<=}8.0x10{sup 21} s{sup -1}. (orig.).
We consider particle evaporation and fission of an ensemble of hot, rotating compound nuclei as a stochastic process. We derive a set of coupled differential equations formed by a Fokker-Planck equation describing fission, and master equations for calculating particle evaporation. From these equations, we are able to determine multiplicities of prefission neutrons, protons and #alpha#-particles, their energy spectra and their angular momentum distributions. A comparison of our results with experimental data provides us with information regarding the reduced friction coefficient #beta#, the fission barrier height and the level density parameter. For different iridium isotopes, ("1"8"1","1"8"5","1"8"7Ir), "1"8"5Os and "1"5"8Er, we obtain as an upper limit #beta##<=#8.0x10"2"1 s"-"1. (orig.).
The subject of Tachyons, even if still speculative, may deserve some attention for reasons that can be divided into a few categories, two of which are as follows: The larger scheme, to build up in order to incorporate space-like objects in the relativistic theories. These allow better understanding of many aspects of the ordinary relativistic physics, even if Tachyons would not exist in our cosmos as ''asymptotically free'' objects; superliminal classical objects can have a role in elementary particle interactions (perhaps even in astrophysics) and possible verification of the reproduction of quantum-like behaviour at a classical level when taking into account the possible existence of faster-than-light classical particles. This paper shows that Special Relativity - even without tachyons - can be given a form which describes both particles and anti-particles. This paper also is confined only to a ...