Energy Technology Data Exchange (ETDEWEB)

The purpose of this project was to investigate the origin of pressure fluctuations in fluidized bed systems. The study assessed the potential for using pressure fluctuations as an indicator of fluidized bed hydrodynamics in both laboratory scale cold-models and industrial scale boilers. Both bubbling fluidized beds and circulating fluidized beds were evaluated. Testing including both cold-flow models and laboratory and industrial-scale combustors operating at elevated temperatures. The study yielded several conclusions on the relationship of pressure fluctuations and hydrodynamic behavior in fluidized beds. The study revealed the importance of collecting sufficiently long data sets to capture low frequency (on the order of 1 Hz) pressure phenomena in fluidized beds. Past research has tended toward ...

Science.gov (United States)

Sandia National Laboratories has developed a family of airfoils specifically designed for use in the equatorial portion of a Vertical-Axis Wind Turbine (VAWT) blade. An airfoil of that family has been incorporated into the rotor blades of the DOE/Sandia 34-m diameter VAWT Test Bed. The airfoil and rotor design process is reviewed. Comparisons with data recently acquired from flow visualization tests and from the DOE/Sandia 34-m diameter VAWT Test Bed illustrate the success that was achieved in the design. The economic optimization model used in the design is described and used to evaluate the effect of modifications to the current Test Bed blade. 1 tab., 11 figs., 13 refs.

Science.gov (United States)

Sandia National Laboratories has erected a research oriented, 34- meter diameter, Darrieus vertical axis wind turbine near Bushland, Texas. This machine, designated the Sandia 34-m VAWT Test Bed, is equipped with a large array of strain gauges that have been placed at critical positions about the blades. This manuscript details a series of four-point bend experiments that were conducted to validate the output of the blade strain gauge circuits. The output of a particular gauge circuit is validated by comparing its output to equivalent gauge circuits (in this stress state) and to theoretical predictions. With only a few exceptions, the difference between measured and predicted strain values for a gauge circuit was found to be of the order of the estimated repeatability for the measurement system.

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy (DOE) Subsurface Contamination Focus Area (SCFA) sponsored a technology demonstration of non-traditional in situ vitrification (NTISV) at Los Alamos National Laboratory (LANL). The project team for this demonstration included MSE Technology Applications, Inc., Geosafe Corporation, and LANL. The technology demonstration involved the performance of two large-scale test melts. The first, referred to as the ''cold'' test, was performed on a simulated absorption bed that contained surrogate contaminants. The cold test was conducted in April 1999. The second demonstration, referred to as the ''hot'' test, took place at LANL's Material Disposal Area (MDA) V in April 2000. The hot test was conducted on a portion of an absorption ...

Energy Technology Data Exchange (ETDEWEB)

Results from a numerical model of axisymmetric solar cavity receivers are compared with experimental data for tests of a novel test bed receiver in the Saudi National Laboratories solar furnace. The computed energy transfer rates and temperatures are compared with the experimental data for different receiver geometries, aperture sizes, and operating conditions. In general, the agreement between the numerical model and the experimental data is better for the small-to-midsized apertures than for the large apertures. The analysis indicates that for the larger apertures, the convective heat losses are overpredicted. It also suggests that these losses could be better characterized. Sensitivity analyses show that both the total solar energy input rate and the convective heat-loss coefficient significantly affect the receiver thermal performance and that the distribution of the input solar flux significantly ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 deg. C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed at a higher ...

British Library Electronic Table of Contents (United Kingdom)

Greenman J, Thorn RMS, Saad S, Austin AJ. In vitro diffusion bed, 3-day repeat challenge `capacity' test for antimicrobial wound dressings. Int Wound J 2006;3:322-329. Abstract The aim of this study was to develop an in vitro wound infection model that allows the comparison of the bacterial kill rate of antimicrobial wound dressings over the course of 3 days, with renewed microbial challenges each day, under realistic wound-like conditions. A test bed model of a moderately exuding wound was constructed from a hydrogel containing releasable foetal calf serum (FCS), and cellulose discs dosed with test microbes (Methicillin-resistant Staphylococcus aureus and Pseudomonas aeruginosa) suspended in 50% FCS applied at the interface between the test dressing and the hydrogel test bed. Freshly prep...

Science.gov (United States)

test bed (ADTT) tools technology. Glenn. Research. Center: Aircraft icing training video for regional and cor- porate pilots. Numerical propulsion ...

Science.gov (United States)

Jan 22, 2004 ... Training and Professional Development Leadership Development Program. GSFC Leadership Development Program Positions. Cryo-Optical ...

Energy Technology Data Exchange (ETDEWEB)

FIU-HCET participated in an ICT meeting at Mound during the second week of December and presented a brief videotape of the testing of the Robotic Climber technology. During this meeting, FIU-HCET proposed the TechXtract technology for possible testing at Mound and agreed to develop a five-page proposal for review by team members. FIU-HCET provided assistance to Bartlett Inc. and General Lasertronics Corporation in developing a proposal for a Program Opportunity Notice (PON). The proposal was submitted by these companies on January 5, 1999. The search for new equipment dismantlement technologies is continuing. The following vendors have responded to requests for demonstration: LUMONICS, Laser Solutions technology; CRYO-BEAM, Cryogenic cutting technology; Waterjet Technology Association, Waterjet Cutting technology; and DIAJET, Waterjet Cutting technology. Based on the tasks done in FY98, FIU-HCET is working closely with Numatec Hanford ...

Energy Technology Data Exchange (ETDEWEB)

This purpose of this report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period April 1, 2005 through June 30, 2005. The following tasks have been completed. First, the new Combustion Laboratory was occupied on June 15, 2005, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final painting stage. Second, the fabrication and manufacturing contract for the CFBC Facility was awarded to Sterling Boiler & Mechanical, Inc. of Evansville, Indiana. Sterling is manufacturing the assembly and component parts of the CFBC system. The erection of the CFBC system is expected to start September 1, 2005. Third, mercury emissions from the cofiring of coal and chicken waste was studied experimentally ...

Energy Technology Data Exchange (ETDEWEB)

In the new system presented in this paper, the cement clinker is sintered, not in a rotary kiln, but in two different furnaces: a spouted bed kiln and a fluidized bed kiln. The heat generated in the process of cooling the cement clinker is recovered by a fluidized bed cooler and a packed bed cooler, which are more efficient than the conventional coolers. Compared with the rotary kiln system, the new technology significantly reduces NO{sub x} emissions, appreciably cuts energy consumption, and reduces CO{sub 2} emissions as well. Thus, the new system is an efficient cement sintering system that is friendly to the global environment. In this paper, we describe this new technology as one of the applied technologies at an industrial level that is being developed in the Clean Coal Technology Project, and we present the results from test operations at our pilot plant.

Energy Technology Data Exchange (ETDEWEB)

One of the design targets for the ITER Tokamak Exhaust Processing system is not to lose more than 10{sup -5} g h{sup -1} into the Normal Vent Detritiation System of the Tritium Plant. The plasma exhaust gas, therefore, needs to be processed in a way that an overall tritium removal efficiency of about 10{sup 8} is reached. Such a high decontamination factor can only be achieved by multistage processes. The third step of the three step CAPER process developed at the TLK is based on a so-called permeator catalyst (PERMCAT) reactor, a direct combination of a Pd/Ag permeation membrane and a catalyst bed. The PERMCAT principle is based on isotopic swamping in a counter current mode. Previous tritium experiments employing laboratory scale PERMCAT reactors have revealed decontamination factors as high as 10{sup 5} for the third CAPER step. First tritium tests with a technical scale PERMCAT reactor led to similar decontamination ...

Science.gov (United States)

During the erection of the Sandia 34-Meter VAWT Test Bed, the induced gravitational stress state in the turbine blades and their associated deflections were measured. This manuscript details the measurements that were taken on the Test Bed blades during erection and compares them to the stresses and deflections predicted by the NASTRAN finite element code.

International Nuclear Information System (INIS)

Full text: During JET operations, tritium contaminated waste is generated principally but not exclusively from 'intervention' work and from removing or replacing redundant items. It is essential for JET and for any future fusion plant to have available a route for managing each waste stream however large or small, both during operation and decommissioning of the plant. The long term outcome is to have for each tritiated waste stream from JET a route for its management leading to its eventual disposal or recycling (and thus to be available for similar waste streams which will be produced by ITER operations). Since several years SCK#centre dot#CEN has been developing techniques for the treatment of tritiated waste. Amongst them, technologies for water detritiation, for the treatment of tritiated organic liquids and for the decontamination of several types of solid tritiated waste. Our R and D focuses on the development of a system to decontaminate surface contaminated metals, concrete ...

Energy Technology Data Exchange (ETDEWEB)

CoTreat, a new inorganic ion exchange media, has been studied in the laboratory to support its application as a pre- coat to existing Funda filters in THORP feed pond plant (Sellafield, UK). This is a novel way of application of CoTreat, which is usually utilized in fixed-bed ion exchange columns in a granular form. The results present the effect of operating conditions (CoTreat dose, pond water chemistry) on CoTreat performance for the removal of Co-57 tracer from simulated pond water. Major findings include the strong dependence of Co-57 decontamination factor (DF) on feed activity. At the 200 Bq/L feed level, the observed DF was 10-20 but rose to 1000 and above when the feed level was increased to 20000 Bq/L. Calcium present in the feed was found to decrease the DF at concentrations higher than 1 ppm. The laboratory studies showed significantly higher DF's than what has been observed in large-scale THORP ...

Energy Technology Data Exchange (ETDEWEB)

Small-scale stoves, producing heat and hot water, are suited for domestic purposes. In order to optimise their efficiency when using lignocellulosic pellets, an important task is to do research on their real performance. The general behaviour depends on many operational factors (air flow and humidity, pressure, etc), dimension and pellet characteristics (moisture, size, raw material, density, friability, etc). In this paper, the first results and general performance of a 24 kW pellet fixed bed stove pilot plant are presented. The plant has been designed to study pellet combustion in the laboratory. The main targets are to reduce emissions of pollutants and to improve energy efficiency. Different situations can be simulated and tested due to its flexible design. Temperatures, pressures, flows and emissions are measured and analysed. An extensive study of different load conditions is presented through the application of both ...

Energy Technology Data Exchange (ETDEWEB)

In the atmospheric pressure coal combustion area, the internally circulating fluidized bed boiler (ICFB) has already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and los pollution characteristics. Cold model tests and computer simulation have been carried out to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the pressurized internally circulating fluidized bed boiler (PICFB). Based on the results achieved in this research, a hot-model ...

British Library Electronic Table of Contents (United Kingdom)

The fossil fuel consumption and pollutant emissions in a coal fired fluidized bed boiler could be reduced by biomass pyrolysis gas reburning. The influence of three kinds of biomass pyrolysis gases on the emission of N2O in a laboratory scale fluidized bed was investigated using the mechanism of GRI3.0 in this paper. The results showed that: the effect of sawdust pyrolysis gas reburning on N2O was more significant than that of rice husk and orange peel under the same conditions; the increase of initial oxygen content from 1% to 8% in flue gas would restrain the decomposition of N2O; the N2O decomposition was enhanced by increasing reaction temperature from 1073.15 K to 1323.15 K, and the decomposition rate may reach 99% at 1223.15 K.

Energy Technology Data Exchange (ETDEWEB)

The paper reports a work-in-progress outlook of a R and D project aimed at developing an advanced boiler for the combustion of virgin and exhaust olive husks at small scale. Fluidized bed technology has been preferred because of its well known advantages that include large thermal inertia, high combustion efficiency, low NOx emissions and considerable heat transfer rate. A 100 kW atmospheric bubbling fluidized bed combustor has been designed and built. The facility is equipped with devices for continuous fuel feeding as well as heat extraction from the bed region. Measurements of temperature and gas concentrations are obtained by using thermocouples and gas-analyzer. Steady state tests of combustion were carried out at typical fluidized bed combustion temperatures. Tests proved that not only exhaust olive husks but also the virgin ones - with a water content ...

International Nuclear Information System (INIS)

Between December 2001 and May 2004, a ventilation experiment (VE) was performed in the Mont Terri Underground Research Laboratory (URL) and co-financed by the Commission of the European Communities. The objective was to investigate the desaturation of consolidated clay formations in consequence of the ventilation of underground openings of a repository in such a formation. The results of the geoelectric measurements performed in the second phase of the Mont Terri ventilation test can be summarized as follows: Geoelectric tomography has been found suitable for monitoring ventilation-induced saturation changes in the Opalinus clay. During ventilation with dry air a desaturation down to below 50% could be detected in both desaturation cycles. The desaturated zone extends less than 0.5 m into the rock around the microtunnel. During the second resaturation phase, ventilation with humid air led to quick resaturation at the tunnel surface, while ...

International Nuclear Information System (INIS)

Nitric acid leaching from the weak base anion (WBA) exchanger had been evaluated and based on this a 5% mixture of nitric acid loaded weak base anion exchanger with fresh weak base anion exchanger (NLWBA) at the bottom of the ion exchange column has been devised to maintain an outlet pH in the range of 5.0 to 5.5 during Gd removal from the moderator system of TAPP - 3 and 4. A three layered bed had been constituted wherein strong acid cation (SAC) exchanger is placed as the top layer while a mixed bed of SAC and WBA or pure WBA is used as the middle layer and the 5% NLWBA was used as the bottom most layer. This bed configuration would result in an iso-pH regime in the moderator system during the Gd removal along with quantitative removal of Gd. Two three-layer bed columns were prepared at TAPS - 3 and 4 in July 07. The resin was loaded in batches and after preparing the column, the column was deuterated ...

Energy Technology Data Exchange (ETDEWEB)

The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. Along with the major activity of assembling the components of the 50-lb/hr retort, work was also completed in other areas this quarter. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market applications for KENTORT II-derived products, a study of the synthesis of carbon fibers from the heavy fraction of KENTORT II shale oil was initiated.

Energy Technology Data Exchange (ETDEWEB)

Laboratory studies were performed to support field-testing of base injection into the F-Area Seepage Basins groundwater. The general purpose of these experiments is to provide information to guide the test of base injection and to identify potential adverse effects.

Energy Technology Data Exchange (ETDEWEB)

This report summarizes work performed on this project from October 2004 through March 2005. In previous work, a surfactant modified zeolite (SMZ) was shown to be an effective system for removing BTEX contaminants from produced water. Additional work on this project demonstrated that a compost-based biofilter could biodegrade the BTEX contaminants found in the SMZ regeneration waste gas stream. However, it was also determined that the BTEX concentrations in the waste gas stream varied significantly during the regeneration period and the initial BTEX concentrations were too high for the biofilter to handle effectively. A series of experiments were conducted to determine the feasibility of using a passive adsorption column placed upstream of the biofilter to attenuate the peak gas-phase VOC concentrations delivered to the biofilter during the SMZ regeneration process. In preparation for the field test of the SMZ/VPB treatment system in New Mexico, a pilot-scale SMZ ...

Energy Technology Data Exchange (ETDEWEB)

This report forms part of an independent review of the specifications, execution and results of Task 6 of the Aespoe Task Force on Modelling of Groundwater Flow and Transport of Solutes, which is seeking to provide a bridge between site characterization (SC) and performance assessment (PA) approaches to solute transport in fractured rock. The present report is concerned solely with Task 6C, which relates to the construction and parametrisation of a block-scale hydrostructural model of the TRUE Block Scale region of the Aespoe Hard Rock laboratory. The task objectives, specifications and outcome are summarised and reviewed. Also, consideration is given to how the hydrostructural model might affect the outcomes of Task 6D and 6E. The main conclusions of this review are summarised below: The Task 6C hydrostructural model is a more comprehensive approach to quantitatively describing a volume of fractured rock than has been achieved hitherto. The idea of including ...

Energy Technology Data Exchange (ETDEWEB)

This study aims to develop a particulate model combining solid waste particle combustion and heavy metal vaporization from burning particles during MSW incineration in a fluidized bed. The original approach for this model combines an asymptotic combustion model for the carbonaceous solid combustion and a shrinking core model to describe the heavy metal vaporization. A parametric study is presented. The global metal vaporization process is strongly influenced by temperature. Internal mass transfer controls the metal vaporization rate at low temperatures. At high temperatures, the chemical reactions associated with particle combustion control the metal vaporization rate. A comparison between the simulation results and experimental data obtained with a laboratory-scale fluid bed incinerator and Cd-spiked particles shows that the heavy metal vaporization is correctly predicted by the model. The predictions are better at higher ...

Energy Technology Data Exchange (ETDEWEB)

The main purposes of this research was to investigate the feasibility of incineration of wool-scouring sludge in a novel vertical-axis-rotating fluidised bed (RFB). The experiment was carried out in a RFB with an internal diameter (ID) of 200 mm and height of 50 mm. A cold test was first conducted to investigate the fluidization performance of the RFB via parameters such as the bubbling, gas distribution, bed shape and pressure drop. The tumbling phenomena was observed in the bed, and this effectively enhanced the axial mixing. The appropriate range of bed thickness, rotating speed and sand particle size were identified to ensure the full fluidization and reduce the particle elutriation. Four wool-scouring sludges from different processes were incinerated in the RFB. With 5% support methane, all sludges with a maximum moisture up to 70% as received could be successfully burned in ...

Energy Technology Data Exchange (ETDEWEB)

A description of the FEL experiment underway at the 10 kA, 5 MeV Experimental Test Accelerator (ETA) is described. The facility has been designed to investigate the high-gain operation of an FEL.

Energy Technology Data Exchange (ETDEWEB)

Tests with a 61 cm diameter fluidized-bed combustor revealed that raw cotton gin trash could be efficiently burned while satisfying Federal standards for particulate emissions. Certain chemicals within cotton gin trash zone can cause slagging or caking of ash and bed particles in the combustion zone. They can also corrode and accumulate on the heat recovery equipment. These problems are not considered insurmountable and methods of control are being studied. Raw cotton gin trash was also converted into a low Btu gas using fluidized-bed technology. Tests with a 30 cm diameter gasifier revealed that raw gin trash could be converted to a combustible gas, containing carbon monoxide and hydrogen. The heating value of the gas ranged from 3.65 to 5.29 MJ/m3 and about 50 percent of the heat value of the raw trash was converted to combustible gases. Economic analyses have shown that these ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a 400 MW(th) sodium cooled reactor and is the largest test reactor of its type in the world. It was designed and is being operated to serve two purposes: gaining liquid metal system experience and serving as a test bed for fuels and materials. During test operations it is possible that cladding breaches and escape of fission gas to the reactor cover gas region can occur. To identify the source of such a leak all 78 fuel pin assemblies contain ''gas tag'' with a unique ''tag'' mixture in each assembly. The mass spectrometric identification of tag isotope ratios makes possible rapid location and thus faster removal (if required) of breached test pins.

International Nuclear Information System (INIS)

An alkaline-side solvent extraction process was developed for cesium removal from Savannah River Site (SRS) tank waste. The process was invented at Oak Ridge National Laboratory and developed and tested at Argonne National Laboratory using singlestage and multistage tests in a laboratory-scale centrifugal contactor. The dispersion number, hydraulic performance, stage efficiency, and general operability of the process flowsheet were determined. Based on these tests, further solvent development work was done. The final solvent formulation appears to be an excellent candidate for removing cesium from SRS tank waste.

Energy Technology Data Exchange (ETDEWEB)

Combustion characteristics of Korean anthracite in a circulating fluidized bed and freeboard were investigated. A test coal was selected with heating value of 4,429kcal/kg and ash content of 38%. Characteristics of combustion, sorbent effect on desulphurisation and emission of SO{sub x} and NO{sub x} were monitored by varying process variables such as feed rate, (Ca+K)/S ratio, and excess air ratio at the given properties of coal. Optimum operating conditions were studied by analysing: axial profiles of temperature, effect of excess air ratio, characteristics of loopseal and bag filter ashes, and emission of toxic gases. 9 refs., 9 figs., 3 tabs.

Science.gov (United States)

material may survive intact and mix back into interstellar gas clouds, helping to fuel the next generation of stars. NASA's Jet Propulsion Laboratory, Pasadena, Calif.,...

International Nuclear Information System (INIS)

... Industry, Material Science Research Laboratory, Yokosuka, Kanagawa (Japan)

Science.gov (United States)

... Standards Validation Group National Computer Systems Laboratory National Institute of Standards and Technology ... STANDARD. ... (See test Ci )i3A. ...

Energy Technology Data Exchange (ETDEWEB)

Human beings are confronted with another grievous disaster - coal fire. The monitoring on underground coal bed combustion relied on drilling supervising in the past, but this method is not good. By taking the coal fire of Gulaben mine in Inner Mongolia Autonomous Region as an example, the monitoring methods of underground coal bed combustion were explored based on the hyperspectra and high-resolution remote sensing technology. By employing the OMIS imaging apparatus developed by Shanghai Institute of Technical Physics of Chinese Academy of Sciences, the airborne hyperspectral images and the characteristic spectra of different types were obtained and the temperature was measured synchronously on the ground. Then according to the correlation of DN value of the thermal infrared band and surface temperature, the image information was processed, the spectral features were analyzed, and the surface temperature retrieval model was built. Finally, by ...

Energy Technology Data Exchange (ETDEWEB)

Experimental and theoretical investigation on drying of a single coal particle in fluidized bed combustor is presented. Coal particle drying was considered via the moist shrinking core mechanism. The results of the drying test runs of low-rank Serbian coals were used for experimental verification of the model. The temperature of the coal particle center was measured, assuming that drying was completed when the temperature equalled 100{sup o}C. The influence of different parameters (thermal conductivity and specific heat capacity of coal, fluidized bed temperature, moisture content and superheating of steam) on drying time and temperature profile within the coal particle was analyzed by a parametric analysis. The experimentally obtained results confirmed that the moist shrinking core mechanism can be applied for the mathematical description of a coal particle drying, while dependence between drying time and coal particle ...

Energy Technology Data Exchange (ETDEWEB)

Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to develop a pellet formulation which is capable of achieving low sulfur partial pressures and a high capacity for sulfur, loaded from a hot fuel gas and which is readily regenerable. Furthermore the pellet must be strong for potential use in a fluidized bed and regenerable over many cycles of loading and regeneration. Regeneration should be in air or oxygen-depleted air to produce a high-concentration sulfur dioxide. Fixed-bed tests were conducted with several formulations of manganese sesquioxide and titania, and alumina They were subject to a simplified fuel gas of the oxygen-blown Shell type spiked with a 30,000ppmv concentration of H{sub 2}S. Pellet crush strengths for 4 and 2mm diameter pellets was typically 12 lbs per pellet and 4 lbs per pellet, respectively. For the most favorable of the formulations tested and under the criteria of break-through at less than ...

Energy Technology Data Exchange (ETDEWEB)

The document describes the outcome of the CSN/CIEMAT-00 interlaboratory test comparison among environmental radioactivity laboratories. the exercise was organised according to the ISO-43 and the ISO/IUPAC/AOAC Harmonized Protocol for the proficiency testing of analytical laboratories. the test sample was a soil containing environmental levels of K-40, Ra-226, Ac-228, Sr-90, Cs-137, Cs-134, Pu (239-240) y Am-241. the Universidad Autonoma de Barcelona prepared the material and reported adequate statistical studies of homogeneity. The results of the exercise were computed for 30 participating laboratories, and their analytical performance was assessed using the u-score approach. A raised percentage of satisfactory laboratory performance has been obtained for all the analysis, being the best performance in gamma measurements. The exercise has ...

British Library Electronic Table of Contents (United Kingdom)

A laboratory-scale multi-layer system was developed for the adsorption of PCDD/Fs from gas streams at various operating conditions, including gas flow rate, operating temperature and water vapor content. Excellent PCDD/F removal efficiency (>99.99%) was achieved with the multi-layer design with bead-shaped activated carbons (BACs). The PCDD/F removal efficiency achieved with the first layer adsorption bed decreased as the gas flow rate was increased due to the decrease of the gas retention time. The PCDD/F concentrations measured at the outlet of the third layer adsorption bed were all lower than 0.1ng I-TEQNm-3. The PCDD/Fs desorbed from BAC were mainly lowly chlorinated congeners and the PCDD/F outlet concentrations increased as the operating temperature was increased. In addition, the r...

Science.gov (United States)

The magnetically fluidized bed (MFB) was used as the reactor in a novel semidry flue gas desulfurization (FGD) process to achieve high desulfurization efficiency. Experiments in a laboratory-scale apparatus were conducted to reveal the effects of approach to adiabatic saturation temperature, Ca/S molar ratio and applied magnetic field intensity on SO(2) removal. Results showed that SO(2) removal efficiency can be obviously enhanced by decreasing approach to adiabatic saturation temperature, increasing Ca/S molar ratio, or increasing applied magnetic field intensity. At a magnetic field intensity of 300Oe and a Ca/S molar ratio of 1.0, the desulfurization efficiency (excluding desulfurization efficiency in the fabric filter) was over 80%, while spent sorbent appeared in the form of dry powder. With the SEM, XRD and EDX research, it can be found that the increase of DC magnetic field intensity can make the surface morphology on the surface of the ...

Energy Technology Data Exchange (ETDEWEB)

A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper provides an overview of the field test site and a description of some of the ...

Energy Technology Data Exchange (ETDEWEB)

A 100 kW thermal input Two-Stage Gasifier was built at the University of Denmark (DTU). The gasifier consists of an externally heated pyrolysis unit, a down-draft char gasifier, a gas cleaning system and an internal-combustion engine. Between the summer of 1996 and the summer of 1998, 11 tests were made with the gasifier. The gasifier had a total operating time of 278 hours (excluding warming up). The fuel was mainly wood chips, but also briquettes has been used. Four of the tests lasted 50-70 hours, and stable conditions were reached. All the tests were completed without technical problems. The particle sizes and amounts were investigated. The amount of particles depended on the amount of steam led to the gasifier. More than 99% of the particles after the cyclone were soot. The size of the soot particles was mainly between 0.2-0.5 {mu}m. Under normal conditions (biomass:steam = 1:1 (dry mass basis)), the particle load was ...

Science.gov (United States)

A multi-centre evaluation of the test strip analyser, Rapimat, was performed by four laboratories following the ECCLS 2nd draft guidelines for the evaluation of analysers in clinical chemistry. Using the Rapignost urine test strip with the test fields for bilirubin, urobilinogen, acetoacetate, ascorbic acid, glucose, protein, nitrite, pH and haemoglobin, the Rapimat was found to be analytically reliable in comparison with other, in most cases quantitative procedures. During the observation period of about 6 months no breakdown occurred in any laboratory. Interferences and sensitivity as discussed for the bilirubin and urobilinogen test field are more related to the test strip than to the instrument. Several improvements for further developments are suggested. This multi-centre study has shown that the ECCLS protocol is applicable to ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports on a series of laboratory and controlled test site measurements of the thermal conductivity of polyisocyanurate foam laminated boardstock roof insulations produced with several different blowing agents; CFC-11, HCFC-123, HCFC-14lb, and two blends of the HCFCs. The behavior of the experimental foams with HCFCs is compared to that of conventional polyisocyanurate foam blown with CFC-11. Thermal drift observed from two years of field exposure is compared to laboratory accelerated aging tests and the laboratory and field measurement techniques are described. This work is part of a Joint Industry/Government Project established in the United States to evaluate the technical viability of HCFC alternative blowing agents for polyisocyanurate foam roof insulations.

CERN Document Server

Having always been at the forefront of information management and open access, High-Energy Physics (HEP) proves to be an ideal test-bed for innovations in scholarly communication including new information and communication technologies. Three selected topics of scholarly communication in High-Energy Physics are presented here: A new open access business model, SCOAP3, a world-wide sponsoring consortium for peer-reviewed HEP literature; the design, development and deployment of an e-infrastructure for information management; and the emerging debate on long-term preservation, re-use and (open) access to HEP data.

Energy Technology Data Exchange (ETDEWEB)

A hypothesis on the transition of a fully water-saturated coal bed methane reservoir from single-phase flow through unsaturated flow to the two-phase flow regime was developed and substantiated using field data. The concept of parameter measurement windows was introduced to obtain the required reservoir parameters from flow testing. A new empirical relationship for capillary pressure vs. saturation, referred to as the Fermi distribution, was developed and shown to fit the capillary pressure-saturation data for coal, sandstone, and other consolidated and unconsolidated materials. New approximate analytic solutions for flow to a sink from an infinite coal bed reservoir with desorbing methane have been developed and verified using numerical models for the following cases: (1) single-phase gas flow with desorption; (2) single-phase water flow in fully water-saturated and unsaturated flow regimes. A numerical model based on ...

Energy Technology Data Exchange (ETDEWEB)

This third report covers the period October 1 to November 30, 1991. During this period the authors: (1) fabricated a test fixture for studying hybrid armature brush behavior, (2) reactivated a 140kJ, 1MA capacitor bank, (3) reactivated 25 channels digital data acquisition and reduction system and (4) concluded the use of a DNA funded railgun would serve as the most expedient means to acquire a railgun test bed. Fabrication of a plasma brush test fixture for studying the formation, evolution and stability of plasma brushes was completed. The fixture will serve to study plasma brush parameters, such as brush length and voltage drop, as a function of initial solid foil mass, gap size and current concentration. A 4OkV, 168{mu}f, 140kJ capacitor bank capable of providing more than 1MA of current was reactivated. (The LLNL bank had been developed for opening switch research which was successfully completed.) ...

Energy Technology Data Exchange (ETDEWEB)

This comprehensive, illustrated report for the Swiss Federal Office of Energy (SFOE) by the University of Applied Sciences in Lucerne, Switzerland takes a look at the testing facility at the university that is used to test compact ventilation systems. These feature heat-recovery and return-air heat-pumps and are used in housing built to low energy-consumption standards such as the Swiss 'Minergie' and 'Minergie-P' standards. The primary goal is a technically comprehensive testing programme for compact ventilation units with heat recovery and heat pumps, which can nevertheless be carried out at reasonable cost. In addition to thermal and flow measurements, acoustic measurements are also carried out. The authors quote that the overall assessment provided can also include service and maintenance, materials used and possible problems with thermal bridges. The test ...

Energy Technology Data Exchange (ETDEWEB)

Rocket-Based Combined-Cycle (RBCC) engines intended for missiles and/or space launch applications incorporate features of rocket propulsion systems operating in concert with airbreathing engine cycles. Performance evaluation of these types of engines, which are intended to operate from static sea level take-off to supersonic cruise or accerlerate to orbit, requires ground test capabilities which integrate rocket component testing with airbreathing engine testing. A combined cycle engine test facility has been constructed in the General Applied Science Laboratories, Inc. (GASL) Aeropropulsion Test Laboratory to meet this requirement. The facility was designed to support the development of an innovative combined cycle engine concept which features a rocket based ramjet combustor. The test requirements included the ability ...

Energy Technology Data Exchange (ETDEWEB)

Qualifying corrosion inhibitors for use in high velocity multiphase flowlines in arctic or subsea environments is discussed. The tests include high velocity flow loop corrosion tests, pumpability through 0.125 (0.318 cm) inch capillary at low temperatures, compatibility with Nylon 11, emulsion tendency testing, and partitioning characteristics. Laboratory and field data show the importance for using the above criteria for inhibitor selection.

Energy Technology Data Exchange (ETDEWEB)

This report is directed at the commercial potential of the 17-m, 100 kW Darrieus Vertical Axis Wind Turbine (VAWT) developed under DOE funding by Sandia National laboratories (SNL) and Alcoa Laboratories. Three of the turbines have come on line over the past 14 months and long-term testing is in progress. As the first commercially adapted Darrieus turbines built by DOE, the superior cost, structural integrity, and output characteristics demonstrated by the prototypes appear particularly promising.

Energy Technology Data Exchange (ETDEWEB)

The operation of the Bullhouse Minewater System, used to treat iron-rich minewaters discharged from long-abandoned coal mines, was studied to minimise pollution of the Upper Don river in the UK. Tests were carried out to determine optimal operating conditions. Ochre flocculation with polyacrylamide was efficient in batch tests as the ochre self-flocculated and sedimented in the lagoon without the need for chemical enhancement. The rate of accretion of the pipework in the system was modified by partial dewatering, reshaping and hardening of the deposits during ageing. Samples of ochre recovered from the drying beds and sump deposits were converted to ferric sulphate coagulant by dissolution with sulphuric acid and used with a polyelectrolyte to successfully purify reservoir water and pretreat wastewater. There was considerable local interest in the scheme with educational opportunities for schools and colleges.

Energy Technology Data Exchange (ETDEWEB)

Candidate materials for components of a fluidized-bed waste heat recovery system (FBWHRS) include plain carbon steel, types 405 and 316 stainless steel, and alloy 800. These materials were exposed to synthetic flue gas at anticipated FBWHRS temperatures and higher for 3000 h to determine corrosion rates. The synthetic flue gas was a combustion atmosphere to which Cl/sub 2/ and HCl were added. The projected annual corrosion rate for plain carbon steel is about 0.08 mm/year (0.003 in./year) at 250 to 290/sup 0/C, but it would exceed 0.5 mm/year (0.02 in./year) at 560/sup 0/C. The projected annual corrosion rates of the other materials were less than 0.25 mm/year (0.01 in./year) at the maximum test temperatures of 560, 660, and 665/sup 0/C for type 405, type 316, and alloy 800, respectively. These results indicate that corrosion of candidate FBWHRS materials will not be significant at anticipated operating temperatures for various components ...

Energy Technology Data Exchange (ETDEWEB)

Pyrolysis of Greek fir wood samples in a fluidized bed reactor was studied. The experimental conditions selected control the yield of gaseous, liquid and solid products. The factors examined were: pyrolysis temperature, mean particle size, pressure, residence time of volatiles, lignin content of biomass and moisture content. The experiments were performed on the basis of a 12-run Plackett-Burman fractional factorial design. Statistical analysis of the data showed that the pyrolysis temperature is the main factor affecting the distribution of the yields of liquids, their phenolic fraction and gases in the range of experimental conditions tested. Empirical expressions were obtained from linear regression giving the yields of liquids, phenols and gases in terms of temperature. The maximum predicted yields were 56 and 12 wt.% on a moisture-free basis at 520 C and 545 C for liquids and phenols, respectively. The yield of gases increased ...

UK PubMed Central (United Kingdom)

Mycobacterium tuberculosis is the etiologic agent of tuberculosis and can be accurately detected by laboratories using commercial genetic tests. Nontuberculosis mycobacteria (NTM) causing other mycobacterioses...Full Text Available

Wastenet

... Top of page Testing Radiation coming from granite countertops results from natural radioactive material in the granite. Identifying the presence and concentration of radioactive elements in granite requires expensive and sophisticated portable instruments or laboratory equipment. These instruments and equipment require proper calibration, and interpretation of ...

Science.gov (United States)

The effects of freeze-thaw cycling on the strength and durability of samples of compacted, stabilized, wet flue gas desulfurization (FGD) by-products are reported. The results of laboratory tests show a clear relationship between higher water contents and...

Science.gov (United States)

An investigation was carried out to determine the effectiveness of Nomex summer flying coveralls printed with a camouflage pattern as compared with the standard plain olive green coveralls. Laboratory tests indicated that camouflage printing of staple Nom...

Energy Technology Data Exchange (ETDEWEB)

While the methodology used in developing test items can vary significantly, to ensure quality examinations, test items should be developed systematically. Test design and development is discussed in the DOE Guide to Good Practices for Design, Development, and Implementation of Examinations. This guide is intended to be a supplement by providing more detailed guidance on the development of specific test items. This guide addresses the development of written examination test items primarily. However, many of the concepts also apply to oral examinations, both in the classroom and on the job. This guide is intended to be used as guidance for the classroom and laboratory instructor or curriculum developer responsible for the construction of individual test items. This document focuses on written test items, but includes ...

Energy Technology Data Exchange (ETDEWEB)

The Idaho National Engineering Laboratory (INEL) has been conducting geothermal reservoir research and testing sponsored by the US Department of Energy (DOE) since 1983. The INEL research program is primarily aimed at the development of reservoir engineering techniques for fractured geothermal reservoirs. Numerical methods have been developed which allow the simulation of fluid flow and heat transfer in complex fractured reservoirs. Sensitivity studies have illustrated the importance of incorporating the influence of fractures in reservoir simulations. Related efforts include fracture characterization, geochemical reaction kinetics and field testing.

Energy Technology Data Exchange (ETDEWEB)

This paper is a quarterly report describing the use of a new soil gas collection device which allows the collection of soil gas in the field for later analysis in the laboratory. It describes the installation of this sampling device and the procedure for setting the probe, extraction of soil gas beneath the surface, and sealing of the soil gas for transport. The sites used for initial testing was the top of Yucca Mountain and Crystal Spring in Ash Meadows National Wildlife Refuge. The results from this initial test showed no volatile matter present in the soil at these locations.

Energy Technology Data Exchange (ETDEWEB)

Laboratory {open_quotes}jar{close_quotes} tests compared eleven different fuel oil and diesel fuel sludge-control additives. Factors studied included (1) ability to disperse and prevent buildup of sludge deposits on surfaces, (2) ability to protect steel from corrosion, (3) ability to inhibit growth and proliferation of bacteria, and (4) ability to disperse water. Results varied greatly, and it was found that many commercial products do not do what they claim. It is concluded that fuel retailers should not believe manufacturers` claims for their additive products, but rather should test such products themselves to be sure that the benefits of treatment are real. A simplified form of the procedure used here is proposed as one way for dealers to do such testing.

International Nuclear Information System (INIS)

Benthic invertebrates can uptake metals through diffusion of free ion solutes, or ingestion of sediment-bound forms. This study investigated the efficacy of the metal chelating resin SIR 300TM in adsorbing porewater metals and isolating pathways of metal exposure. A field experiment (Botany Bay, Sydney, Australia) and a laboratory toxicity test each manipulated the availability of porewater metals within contaminated and uncontaminated sediments. It was predicted that within contaminated sediments, the resin would adsorb porewater metals and reduce toxicity to invertebrates, but in uncontaminated sediments, the resin would not significantly affect these variables. Whereas in the laboratory, the resin produced the predicted results, in the field the resin increased porewater metal concentrations of contaminated sediments for at least 34 days and decreased abundances of four macroinvertebrate groups, and richness in all ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this report is to advise managers on the status of Year 2000 readiness at the Laboratory and provide a summary of critical issues to be addressed in order to ensure that the Year 2000 date rollover will not disrupt Laboratory Operations. The Laboratory`s Year 2000 council members are in the first phase of Year 2000 plans: gathering data and assessing the status of their divisions or programs. This first snapshot of the Laboratory Year 2000 readiness assessment is expected to grow and change over time as more refined assessments, plans, and schedules are developed and as more information becomes available. Here are findings to date: (1) Embedded systems` status not known. (2) Preliminary cost estimates for Year 2000 repairs, testing, and implementation are estimated to be at least $5.9 million, not including embedded systems. (3) The Laboratory is ...

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little ...

Science.gov (United States)

Clostridium difficile (C. difficile) causes 25-30% of cases of antibiotic associated diarrhea and most cases of pseudomembranous colitis. Patients presenting with diarrhea after hospitalization for 3 or more days should be tested for C. difficile. There are many options available for testing, each of which has inherent advantages and disadvantages. Most laboratories perform toxin testing using an enzyme immunoassay method. In general these tests have sensitivities ranging from 60 to 70% and specificities of 98%. When using these methods, symptomatic patients with negative tests should be tested by another more sensitive method. Until recently, cell culture cytotoxicity neutralization assays (CCNAs) were considered the gold standard in the U.S. A two-step algorithm using an EIA for glutamate dehydrogenase detection followed by ...

Energy Technology Data Exchange (ETDEWEB)

The insulating oil used in a transformer is a critical component, as its service life is typically 20 years with possibly little or no maintenance. Partial discharges (PD), thermal overloads and static discharges continually subject the oil to chemical deterioration during its operating life. To ensure equipment reliability during service, it is important that the initial quality of the new insulating oil should meet the required acceptance specifications and preferably be pre-tested before use. Accelerated aging tests have been devised to determine the life expectancy of oil in service by using forced air or oxygen flow into the oil, the presence of a copper catalyst, and at elevated temperatures. The more important standards relating to transformer application are discussed and highlights of the more important aspects of the oxidation chemistry of hydrocarbons are included. The ultimate aim of the project is the formulation of better standard ...

Energy Technology Data Exchange (ETDEWEB)

Revolving type fluidized-bed technology, developed by Ebara Corp., is installed in more than 100 facilities worldwide. The technology is applied for waste, coal and in situations where a conventional fluidized bed is difficult to use. Waste and/or coal can be treated and valuable energy can be recovered from a non-renewable source. This paper describes the application of the revolving fluidized bed for waste, coal and tyres.

Energy Technology Data Exchange (ETDEWEB)

A zinc-air battery in a case including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit.

Energy Technology Data Exchange (ETDEWEB)

This volume contains appendices D6 through D8 containing laboratory test data: from MK-F investigation, 1987, Old Rifle and New Rifle sites; on bentonite amended radon barrier material; and from MK-F investigation, 1987, riprap tests.

Energy Technology Data Exchange (ETDEWEB)

This document describes testing of OSI products conducted at Argonne National Laboratory. Sun, IBM, and Clsco hardware platforms were used. Various software packages that implement file transfer and gateway applications were evaluated. The OSI model and GOSIP compliance are briefly discussed. Technical details on OSI addressing and routing are presented. The relationship of this testing to other OSI activities at Argonne and to activities of the national networking community is discussed. Mention is also made of the relationship of DECnet Phase V transition issues.

Energy Technology Data Exchange (ETDEWEB)

The study examined the possibility for fuel ignition by spark discharge caused by induction effects under high voltage transmission lines. Theoretical background information on capacitive spark discharges and fuel ignition processes is given. Laboratory experiments were conducted to test the dependence of fuel ignition on three parameters: impedance in discharge path, multiple discharges, and larger electrode shapes. The results of these tests are discussed in terms of fuel ignition possibilities under high voltage transmission lines.

International Nuclear Information System (INIS)

The collisions of high energy photons produced at an electron-positron collider provide a comprehensive laboratory for testing QCD, electroweak interactions, and extensions of the standard model. The luminosity and energy of the colliding photons produced by backscattering laser beams is expected to be comparable to that of the primary e"+e"- collisions. In this overview, we shall focus on tests of electroweak theory in photon-photon annihilation, particularly #gamma##gamma##->#W"+W"-, #gamma##gamma##->#Higgs bosons, and higher-order loop processes, such as #gamma##gamma##->##gamma##gamma#, Z#gamma# and ZZ. Since each photon can be resolved into a W"+W"- pair, high energy photon-photon collisions can also provide a remarkably background-free laboratory for studying WW collisions and annihilation. We also review high energy #gamma##gamma# tests of quantum chromodynamics, ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a 400 Mwt sodium-cooled fast reactor operating at the Hanford Engineering Development Laboratory, Richland, Washington, to conduct fuels and materials testing in support of the US Liquid Metal Fast Breeder Reactor (LMFBR) program. Startup and initial power testing included a comprehensive series of nonnuclear and nuclear tests to verify the thermal, hydraulic, and neutronic characteristics of the plant. A specially designed series of natural circulation tests were then performed to demonstrate the inherent safety features of the plant. Early in 1982, the FFTF began its first 100-day irradiation cycle. Since that time the plant has operated very well, achieving a cycle capacity factor of 94% in the most recent irradiation cycle. Seventy-five specific test assemblies and 25,000 individual fuel pins have ...

Energy Technology Data Exchange (ETDEWEB)

In 1976, the US Department of Energy and New York State - ERDA granted a contract for the development of a +-600 kV dc underground transmission cable system looking to inevitable future requirements in the US for economic, high-capacity, long-distance underground transmission linking remote generating stations to metropolitan load centers. This project was comprehensive and dealt with three separate system components, i.e., cable, splice, and terminals. In each instance, for each component, development required an intensive R and D effort, focused on the following categories: insulating materials, model testing, design of full-scale prototype, manufacturer of prototype, and laboratory development testing. Insulating papers and oils were selected, and model studies performed, for both self-contained type and pipe type oil-filled cables. However, only the pipe cable design was finally designated for full-size cable ...

Energy Technology Data Exchange (ETDEWEB)

The oxidation of carbon black, CB, in presence of CeO{sub 2} is investigated to gain a better understanding of the effect of the contact between the two solids during this reaction. Different CB/CeO{sub 2} mixtures are tested in a fixed bed reactor. The experimental data are used to propose a model for CB oxidation in presence of CeO{sub 2}. It accounts for the size distribution of CeO{sub 2} particles, the contact area between CB and CeO{sub 2}, the mass of CB in the sample and the initial ratio CB/CeO{sub 2}. Corresponding kinetic parameters are determined. 35 refs., 10 figs., 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a PEM fuel cell. The analysis of this process requires determination of the effective thermal conductivity as well as the thermal contact resistance associated with the interface between the GDL and adjacent surfaces/layers. In the present study, a custom-made test bed that allows the separation of effective thermal conductivity and thermal contact resistance in GDLs under vacuum and ambient conditions is described. Measurements under varying compressive loads are performed using Toray carbon paper samples with a porosity of 78% for a range of thicknesses. The measurements are complemented by compact analytical models that achieve good agreement with experimental data. A key finding is that ...

Energy Technology Data Exchange (ETDEWEB)

Petrographical analysis is a microscopical analytical tool which allows definition of the exact nature of the components of different concrete mixes, as well as definition of internal structures and alteration processes. In order to improve the precision and the swiftness of the petrographical analysis, an automated image analysis system has been developed. In the next stage of this study, which consisted in the testing of new concrete mixes containing fluidised bed ashes, petrography has been used, not only to identify the nature of the mix components, but also assess the behaviour of these new concrete mixes when exposed to aggressive conditions.

Energy Technology Data Exchange (ETDEWEB)

A prototype hydride storage bed, using LaNi{sub 4.25}Al{sub 0.75} as the storage material, was fitted with strain gages to measure strains occurring in the stainless steel bed vessel caused by expansion of the storage powder upon uptake of hydrogen. The strain remained low in the bed as hydrogen was added, up to a bed loading of about 0.5 hydrogen to metal atom ratio (H/M). The strain then increased with increasing hydrogen loading ({approximately} 0.8 H/M). Different locations exhibited greatly different levels of maximum strain. In no case was the design stress of the vessel exceeded.

International Nuclear Information System (INIS)

Liquid radioactive raffinates from nuclear fuel reprocessing at the Idaho National Engineering and Environmental Laboratory were solidified, or calcines, in a fluidized bed reactor at approximately 500 C to form a dry granular material. This calcine has been provisionally stored near-surface in concrete-encased stainless steel bins at the Idaho Nuclear Technology Engineering Center. Research addressing the permanent immobilization of radioactive waste has been ongoing. One option is to separate the radioactive constituents from the calcine, thereby reducing the radioactive waste volume to be ultimately stored at a national nuclear waste repository. Nitric acid dissolution of the calcine is a key front-end unit operation in the separations option. In order to design calcine dissolution equipment, quantification of dissolution reaction rate parameters is required. A pilot-plant-produced, non-radioactive calcine was utilized to study the ...

Energy Technology Data Exchange (ETDEWEB)

A testing program has been conducted by the Westinghouse Hanford Company to confirm the baseline waste form selection for use in Waste Receiving and Processing (WRAP) Module 2A. WRAP Module 2A will provide treatment required to properly dispose of containerized contact-handled, mixed low-level waste at the US Department of Energy Hanford Site in south-central Washington State. Solidification/stabilization has been chosen as the appropriate treatment for this waste. This work is intended to test cement-based, thermosetting polymer, and thermoplastic polymer solidification media to substantiate the technology approach for WRAP Module 2A. Screening tests were performed using the major chemical constituent of each waste type to measure the gross compatibility with the immobilization media and to determine formulations for more detailed testing. Surrogate materials representing each of the eight waste types ...

International Nuclear Information System (INIS)

Recent nuclear power plants require high purity water to protect nuclear reactors or steam generators from SCC and maintain in good condition. In this connection, it is especially important to minimize sulfate, which is a corrosive chemical originated from oxidative degradation of cation exchange resins during operation. Recently, uniform particle size (UPS) strong acid cation gel resin with 14% cross-linkage, which has excellent stability against oxidization, has been applied to several condensate purification systems. For further improvement of water quality, some methods for changing the configuration of condensate demineralizer's resin bed have been examined. For example, these methods correspond to anion under layer and cation over layer. We have tested these methods by cold column tests. Furthermore, we have developed the newly anion exchange resin having higher efficiency and capacity for absorbing leachables from ...

International Nuclear Information System (INIS)

We provide a detailed overview of an on-going, multinational test programme that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolised materials plus volatilised fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy/density device. The programme participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research programme. Sandia National Laboratories has the lead role for conducting this research programme; test programme support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. We provide a summary of the overall, multiphase ...

International Nuclear Information System (INIS)

The authors provide a detailed overview of an on-going, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy-density device. The program participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research program. Sandia National Laboratories has the lead role for conducting this research program; test program support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. The authors provide a summary of the overall, ...

Energy Technology Data Exchange (ETDEWEB)

This document describes testing and computation procedures used to generate a photovoltaic Module Energy Rating (MER). The MER consists of 10 estimates of the amount of energy a single module of a particular type (make and model) will produce in one day. Module energy values are calculated for each of five different sets of weather conditions (defined by location and date) and two load types. Because reproduction of these exact testing conditions in the field or laboratory is not feasible, limited testing and modeling procedures and assumptions are specified.

International Nuclear Information System (INIS)

Real-time neutron radiography (RTNR) is rapidly becoming a valuable tool for nondestructive testing and basic research with a wide variety of applications. The Phoenix Memorial Laboratory (PML) at the University of Michigan has developed an RTNR facility and has been using this facility to study several phenomena of interest to researchers in many areas. These phenomena include imaging of the internal fluid flow in gas turbine engine nozzles and coking and debris deposition in several gas turbine nozzles. This paper presents a summary of the technique and facilities involved in these applications.

British Library Electronic Table of Contents (United Kingdom)

In Europe, the use of anti-EGFR monoclonal antibodies is restricted to Kirsten RAS (KRAS) wild-type colorectal tumors. Information on the KRAS status of the patients tumor is thus key for clinical practice; however, there is little guidance or definition on which KRAS mutations to assess and how to assess them. To ensure the consistency and the quality of KRAS test results in Europe, an interlaboratory control network needs to be set up. This pilot study aimed to identify the variables that need to be assessed in a quality control scheme and to provide a first assessment in a selected set of laboratories. Fourteen different tumor cases were circulated between 13 laboratories by a central laboratory acting as the referent for the mutation status determination. This study illustrated that of...

Energy Technology Data Exchange (ETDEWEB)

We are developing a refuelable zinc/air battery (6-cells) for evaluation under the five USABC `core` test protocols. In the first half of the two year project ($1OOK, FY1997), an advanced refuelable design was developed, fabricated and tested at power levels up to 415 W. Performance matched or exceeded that of earlier multicell systems. A computer program was developed for automated data acquisition and drive cycle simulation. Small mockup cells (80 cm 2) were constructed for rapid testing of components. In the follow-on effort (FY1998, $1OOK) we will make minor advances in system design and fabrication efficiency, and seek to improve cathode performance and life, before delivery of two final units for test at DOE laboratory.

Energy Technology Data Exchange (ETDEWEB)

The simulation of the Auxiliary Charcoal Bed (ACB) Vacuum System was performed to evaluate the original vacuum system design, detect and identify design deficiencies, investigate the effects of proposed corrections on system performance, and generally aid in refining the system design before construction and mockup testing. The simulation was performed by using the Advanced Continuous Simulation Language (ACSL). The vacuum system design goals are to provide approximately 20 SCFM of both booster gas and purge gas through the system and maintain a flow of approximately 40 SCFM with a velocity of 50 to 75 f/sec at the entrance to the cyclone separator. The model results showed that the original system design was incapable of meeting the system performance goals. Further simulations showed that the following modifications to the original vacuum system design were required to make the system performance acceptable; (1) Remove valve PCV4. (2) Modify ...

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

Energy Technology Data Exchange (ETDEWEB)

Superconducting rf cavities are increasingly used in accelerators. Gradient is a parameter of particular importance for the ILC. Much progress in gradient has been made over the past decade, overcoming problems of multipacting, field emission, and breakdown triggered by surface impurities. However, the quenching limit of the surface magnetic field for niobium remains a hard limitation on cavity fields sustainable with this technology. Further exploration of materials and preparation may offer a path to surpassing the current limit. For this purpose, we have designed a resonant test cavity. One wall of the cavity is formed by a flat sample of superconducting material; the rest of the cavity is copper or niobium. The H field on the sample wall is 75% higher than on any other surface. Multipacting is avoided by use of a mode with no surface electric field. The cavity will be resonated through a coupling iris with high-power rf at superconducting temperature until the ...

International Nuclear Information System (INIS)

Pilot-scale pyrolysis units have been in operation since 1980 to test the efficiency of thermal treatment of transuranic (TRU) solid waste to retrieve the TRUs and to reduce the volume of wastes such as spent solvent, spent resin, and others. These wastes are generated by reprocessing, fuel production, and utilities. NUKEM has developed a criticality-safe, ring-slab reactor to decompose solid TRU waste. The plant processes 25 kg/h with a polyvinyl chloride content up to 70%. The overall throughput (inactive) up to the spring of 1982 was 2000 kg. The decontamination factor for the reactor itself is 1000. The liquid wastes, mainly spent solvent, are cracked under nitrogen at 400 to 700"0C in a reactor that is filled by a packed bed kept in motion by a specially designed agitator. This unit was built for 15 kg/h water equivalent evaporation. Up to 1982 the unit processed 2000 kg of spent solvent (simulated) overall. The decontamination factor is ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses Test Campaign TC07 of the Kellogg Brown & Root, Inc. (KBR) Transport Reactor train with a Siemens Westinghouse Power Corporation (Siemens Westinghouse) particle filter system at the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama. The Transport Reactor is an advanced circulating fluidized-bed reactor designed to operate as either a combustor or a gasifier using a particulate control device (PCD). The Transport Reactor was operated as a pressurized gasifier during TC07. Prior to TC07, the Transport Reactor was modified to allow operations as an oxygen-blown gasifier. Test Run TC07 was started on December 11, 2001, and the sand circulation tests (TC07A) were completed on December 14, 2001. The coal-feed tests (TC07B-D) were started on January 17, 2002 and completed on April 5, 2002. Due to operational difficulties with the reactor, ...

Energy Technology Data Exchange (ETDEWEB)

A method is proposed for operating bed waters in an oil well by injecting silanes into the near-face zone. It is distinguished by the fact that in order to improve the effectiveness of insulation, the silanes used are silanes of general formula Si /SUB n/ H /SUB 2n-n/ .

Energy Technology Data Exchange (ETDEWEB)

Many of today's automated real-time testing systems for embedded systems were developed using expensive custom hardware and software. In this article they describe how to use commercially available off-the-shelf hardware and software to design and develop an automated real-time test systems for Embedded Programmable Logic Controller (PLC) Based Control Systems. The system development began with the implementation of the VALI/TEST Pro testing methodology as a means for structuring the testing. Using this methodology, they were able to decompose system requirement documents for a Personnel Safety System (PSS) into its high, intermediate and detail level requirements. next, the validation procedures for the PSS system were decomposed into testing units called builds, test runs and test cases. To measure the PSS ...

Energy Technology Data Exchange (ETDEWEB)

In 1977 and 1978, Sandia National Laboratories, located in Albuquerque, New Mexico, and operated for the US Department of Energy (DOE), filmed a series of crash and fire tests performed on three casks designed to transport irradiated nuclear fuel assemblies. While the tests were performed to assess the applicability of scale and computer modeling techniques to actual accidents, films of them were quickly pressed into service by the DOE and nuclear utilities as ``proof`` to the public of the safety of the casks. In the public debate over the safety of irradiated nuclear fuel transportation, the films have served as the mainstay for the nuclear industry. Although the scripts of all the films were reviewed by USDOE officials before production, they contain numerous misleading concepts and images, and omit significant facts. The shorter versions eliminated qualifying statements contained in the longer version, and created false ...

Energy Technology Data Exchange (ETDEWEB)

The influence of common welding defects such as internal under-cut, incomplete penetration of the root bead, internal concavity and hollow bead have been evaluated in a sour environment. Tests were performed on samples cut from actual pipeline welds. The individual defects were subjected to slow strain rate testing. The samples were then examined by metallography, scanning electron microscopy, and hardness testing. It was established that a threshold stress intensity exists for sulphide stress cracking. The test results were compared to those obtained from samples of the weld and pipe which did not contain any defects. This comparison indicated that the metallurgical variations associated with the presence of a weld are the main factor for sulphide stress cracking rather than any specific defects or geometry. 5 tabs., 9 figs.

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion (CLC), has previously been studied as a method for separating CO{sub 2} during combustion of gaseous fuels. In this project the possibility to apply this process for direct use of solid fuels has been investigated. The following has been accomplished: A 10 kW reactor system for CLC with solid fuels has been designed and built. Tests with solid fuel and metal oxid particles in a laboratory reactor show that it is possible to oxidize solid fuels with metal oxide particles in cyclic testing, thus giving proof of basic concept. They also show how the reaction rate is affected by temperature, steam concentration etc., and, most important of all, that the rates of reaction are realistic. Tests with metal oxide materials available at low costs have been successful. Chemical-looping combustion with solid fuels has a potential to achieve very low costs for separation of CO{sub 2}, ...

Science.gov (United States)

Fluidized bed technology was experimentally evaluated for the combustion and gasification of cotton gin waste. The isothermal bed temperatures in the reactors could be maintained below the ash fusion point of the waste. Raw stripper harvested cotton gin trash could be metered directly into the fluidized-bed reactors indicating that little feed preparation is required. H and CO were the primary products of gasification, and approximately 3200-400 Btu of gas were produced per lb of cotton gin waste. These techniques offer the potential of providing small-scale energy conversion systems for use on farms.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The design of high level radioactive waste (HLW) repositories in deep geological media in which bentonite clay is proposed as a sealing material leads to the need of further studying the behaviour of highly compacted expansive soils when subjected to mechanical, hydraulic and thermal changes. Laboratory tests may help to understand the processes that take place in the clay barrier under simple and controlled conditions and to develop the governing equations. The laboratory tests enable to isolate the different processes, making their interpretation easier, and provide with fundamental data concerning the parameters to be used in the models. The extremely low permeability of these materials, their avidity for water (high suction) and their high swelling capacity make necessary the modification of the conventional laboratory techniques and procedures to determine basic physical ...

CERN Document Server

The International Linear Collider Main Linacs are based on superconducting accelerator structures operating at 1.3 GHz. The basis for this design has been developed and tested at DESY and R&D is progressing at many laboratories around the world including DESY, Orsay, KEK, FNAL, SLAC, Cornell, and JLAB. The status of the TESLA-style cavities and rf system will be reviewed and parameters for the ILC linac will be described. The role of the different linac test facilities will discussed and the critical items and R&D program to support a Conceptual Design and Technical Design will be outlined.

Science.gov (United States)

Oak Ridge National Laboratory (ORNL) has for over ten years provided materials testing and failure analysis services to various coal conversion and utilization facilities in the United States. ORNL was involved in these types of activities at all four of the major coal liquefaction pilot plants. This paper presents a summary of activities at Wilsonville over the past two and one-half years. Some details of these activities are discussed below. Failure analysis of elastomers, stainless steels, and alloys is discussed. 6 refs., 9 figs., 13 tabs.

Energy Technology Data Exchange (ETDEWEB)

The wind industry has experienced premature turbine component failures during the past years. With the increase in turbine size, these failures, especially those found in the major drivetrain components, i.e. main shaft, gearbox, and generator, have become extremely costly. Given that the gearbox is the most costly component in the drivetrain to fix, the National Renewable Energy Laboratory (NREL) initiated the Gearbox Reliability Collaborative (GRC) to determine the causes for premature gearbox failures and subsequently, recommend improvements to gearbox design, manufacture, and operational practices. The GRC has two identical test gearboxes, which are planned for a dynamometer and a field test, respectively.

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories, Albuquerque, has been designated as Lead Center for the Exploratory Battery Technology Development and Testing Project, which is sponsored by the US Department of Energy's Office of Energy Storage and Distribution. In this capacity, Sandia is responsible for the engineering development of advanced rechargeable batteries for both mobile and stationary energy storage applications. This report details the technical achievements realized in pursuit of the Lead Center's goals during calendar year 1989. 4 refs., 84 figs., 18 tabs.

International Nuclear Information System (INIS)

A novel device called the gas expansion model (GEM) is being developed at the Hanford Engineering Development Laboratory for testing in the 400-MW(th) fast flux test facility (FFTF) reactor. Incorporation of the GEM into liquid-metal reactor designs is intended to measurably contribute to the achievement of inherent safety, by allowing the reactor to passively shut down even in the extremely remote (hypothetical) event of an unprotected (no scram) loss-of-flow accident. The purpose of this paper is to describe the GEM and present predictive analyses of the effectiveness of the device during unprotected loss-of-flow experiments in the FFTF.

Energy Technology Data Exchange (ETDEWEB)

The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that ...

Energy Technology Data Exchange (ETDEWEB)

The Coal Fired Combined Cycle (CFCC) is the unique powerplant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined cycle powerplant. On the basis of previous studies and confirming work under this contract, General Electric continues to believe that the CFCC approach offers important advantages over alternate approaches: higher powerplant efficiency in the combustor temperature range of interest; reduced combustor/steam generator corrosion potential, due to low fluid-bed tube temperature (as contrasted to the air in tube cycle); and increased gas turbine bucket life from improved material protection systems. The objective of this program is to evaluate the coal fired combined cycle powerplant conceptual design, and to conduct a supporting development program. The supporting development is required for evaluating the pressurized fluidized bed combustion ...

Energy Technology Data Exchange (ETDEWEB)

A joint materials test program developed by the Institute for Mining and Minerals Research (IMMR) and the Tennessee Valley Authority (TVA) involved the postexposure mechanical properties and corrosion behavior of candidate structural materials in an experimental, atmospheric fluidized-bed combustor (AFBC). This combustor was operated by Accurex Corporation at Research Triangle Park, North Carolina, under the direction of TVA. The materials studied were Type 304, Type 310, and INCOLOY alloy 800 in the form of disc coupons with and without crevice configurations. Type 304 was also used for mechanical property measurements. The alloys were exposed to the combustor environment at about840/sup 0/C for approximately 330 hours. The ranking in terms of decreasing weight loss was: (1) Type 304, (2) Type 310, and (3) INCOLOY alloy 800. The presence of tight crevices did not enhance the corrosion rate. In addition, the corrosion rates, based on the weight ...

Energy Technology Data Exchange (ETDEWEB)

This Guideline provides a set of procedures for the measurement of organic contaminants and particles in producer gases from biomass gasifiers. The procedures are designed to cover different gasifier types (updraft or downdraft fixed bed or fluidised bed gasifiers), operating conditions (0 - 900C and 0.6-60 bars) and concentration ranges (1 mg/m{sub n}{sup 3} to 300 g/m{sub n}{sup 3}). The Guideline describes a modular sampling train, and a set of procedures, which include: planning and preparation of the sampling, sampling and post-sampling, analysis, calculations, error analysis and reporting. The modular sampling train consists of 4 modules. Module 1 is a preconditioning module for isokinetic sampling and gas cooling. Module 2 is a particle collection module including a heated filter. Module 3 is a tar collection module with a gas quench (optionally by circulating a liquid), impinger bottles and a backup adsorber. Module 4 is a ...

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. In this capacity, Sandia is responsible for the engineering analyses, contract development, and testing of rechargeable batteries and systems for utility-energy-storage applications. This report details the technical achievements realized during fiscal year 1993.

Science.gov (United States)

Samples of geothermal scale formed from Magmamax No. 1 and Woolsey No. 1 wells in the Imperial Valley, Calif., were exposed to concentrated and dilute solutions of common laboratory reagents. The time of exposure and temperature of the reagent were also varied. Several reagents easily dissolved significant amounts of the scale. An in situ test was performed with marginal success.

Energy Technology Data Exchange (ETDEWEB)

Purpose of the Phase I effort was to demonstrate feasibility of the fuel cell/battery system for powering a small bus (under 30 ft or 9 m) on an urban bus route. A brassboard powerplant was specified, designed, fabricated, and tested to demonstrate feasibility in the laboratory. The proof-of-concept bus, with a powerplant scaled up from the brassboard, will be demonstrated under Phase II.

Energy Technology Data Exchange (ETDEWEB)

The use of nickel alloys in Flue Gas Desulfurization (FGD) applications is described. Recently, nickel alloys 625 and C-276 have been clad to carbon steel plate. Production and properties of the clad plate are reviewed and a brief discussion is presented on production, fabrication and welding. Laboratory and field corrosion tests in SO/sub 2/ scrubber environments suggest that alloy 625 and C-276 clad steel plates are as corrosion resistant as the solid alloy plate.

Science.gov (United States)

Assisted users with expired passwords Closed 233 NCICB Support Wizard Accounts Tickets Set up Resource Accounts for individual developers to control and track access on QA Application servers Maintained daily account synchronization between GForge project developers and CVS write access accounts Created FTP and SFTP user accounts for TCGA test, analysis datasets downloads and analysis datasets management.

Energy Technology Data Exchange (ETDEWEB)

Implementation of an adaptive power system stabilizer (PSS) based on linear optimal control is described in this paper. The generator is identified in real time, and a special 3rd order discrete Riccati equation is solved in each sample interval. Because the output of the generator is fed back directly, the controller can track the system very fast. Experimental studies on a physical model of a power system demonstrate the effectiveness of the proposed adaptive optimal controller.

Energy Technology Data Exchange (ETDEWEB)

This report presents the methodologies and results of the field/laboratory experiments and mathematical modeling defined for the phase III of the project. Results from test cases 2-6 are given in separate chapters of the report (which have been indexed separately), and the last chapter discusses the lessons learned from the three phases of the DECOVALEX project.

Energy Technology Data Exchange (ETDEWEB)

Theoretical and practical aspects of anodic protection for control of corrosion by a wide range of acidic and alkaline solutions are discussed. Chapters are included concerning strategic importance of metals and alloys in modern industry, applications to industrial equipment, descriptions of equipment used in the technique; design, operation and maintenance; economics, scientific principles, characteristics of potentiostats, laboratory tests and procedures, selected application examples and projected future uses. A section is devoted to electrochemical principles.

British Library Electronic Table of Contents (United Kingdom)

Purpose The aim of this study was to evaluate the role of host periosteum and recipient bed perforation on the healing of an onlay graft to the mandible based on histologic and immunohistochemical analysis. Materials and methods Each of the 12 adult sheep used in the study received four iliac corticocancellous onlay bone grafts on the lateral surface of the mandible. In experiment 1, the block graft was placed in direct contact with the recipient bed and fixed with micro-screws, and in experiment 2, the recipient cortical bed was perforated before graft placement. The host periosteum around the graft was excised before flap replacement in experiment 3, and in experiment 4, a sheet of silicone membrane was placed between the graft and the recipient bed. The animals were euthanised at 4, 8, ...

Science.gov (United States)

The concentration and distribution of a soil fumigant in the subsurface of field plots are two key factors in the determination of the fumigant efficacy. Subsurface concentrations of the biologically active compounds cis- and trans-1,3-dichloropropene (1,3-D) and chloropicrin (CP) were determined in soil at two adjacent injection traces and midpoint between the two traces in plastic-covered field beds after injection of the fumigant Telone C35 by conventional chisels or by a coulter rig (Avenger coulters). Two of the four beds were covered with metallic polyethylene film (MPE) and the remaining two were covered with virtually impermeable film (VIF). Three hours after chisel injection, concentrations of the three compounds at the two adjacent injection traces in the two beds were highly variable. Large concentrations of the compounds were detected at the side traces, whereas the compounds were not detected at the middle ...

Energy Technology Data Exchange (ETDEWEB)

Laboratory experiments were conducted to simulate the transfer of acidic THOREX waste from Tank 8D-4 into the alkaline PUREX waste in Tank 8D-2 at West Valley. The purpose of the experiments was to explore means of minimizing the production of nitric oxide (NO) gas during mixing of the two wastes and to assess the potential for the gas to further react in the vapor space possibly leading to enhanced corrosion of the tank walls. Forty one THOREX/PUREX mixing tests were conducted to explore the effects of stirring rate, pH, THOREX addition rate, THOREX or PUREX dilution, and temperature. The two most important criteria for minimizing NO production were to maintain some degree of agitation and the keep the pH in the PUREX high, preferably >12. Steel corrosion tests were performed in the presence of low partial pressures of NO{sub 2} and liquid water or water vapor. The NO{sub 2} (from oxidation of NO in the vapor space) ...

Energy Technology Data Exchange (ETDEWEB)

The newly developed techniques by the Hot Laboratory (JMTR HL) have provided for us the key information on behavior of specimens due to mechanical / physical / chemical / synergistic effects of radiation, stress and water for fission and fusion reactor environment. These techniques are focused on several topics as follows; (1) miniaturized specimen test for the development of fusion reactor materials, (2) slow strain rate tensile testing (SSRT) and crack propagation measuring tests for the study of Irradiation Assisted Stress Corrosion Cracking (IASCC) of core internals of LWR, (3) handling technique on specimens including tritium for the research and development of tritium breeders and neutron multiplier as fusion blanket materials, (4) joining method using the Tungsten Inert Gas (TIG) welding technique for re-assembling of capsule and re-fabrication of specimen and (5) nondestructive evaluation using ...

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories has recently developed two major field test capabilities for unattended ground sensor systems at the Department of energy`s Nevada Test Site (NTS). The first capability utilizes the NTS large area, varied terrain, and intrasite communications systems for testing sensors for detecting and tracking vehicular traffic. Sensor and ground truth data can be collected at either of two secure control centers. This system also includes an automated ground truth capability that consists of differential Global Positioning Satellite (GPS) receivers on test vehicles and live TV coverage of critical road sections. Finally there is a high-speed, secure computer network link between the control centers and the Air Force`s Theater Air Command and Control Simulation Facility in Albuquerque NM. The second capability is Bunker 2-300. It is a facility for evaluating advanced ...

Energy Technology Data Exchange (ETDEWEB)

An Allis-Chalmers, Model 2900, turbocharged diesel engine was converted to a dual-fuel engine in which ethyl alcohol was fumigated between the turbocharger and the intake manifold, and the diesel fuel was injected normally at a reduced rate. Tests were performed to determine if crankcase oil dilution that had occurred was caused by the following independent parameters: proof of the ethyl alcohol, crankcase oil temperature, engine load at maximum torque speed, and percentage of total energy in the form of ethyl alcohol. Engine tests were steady state for six hours, after which the crankcase oil was sampled for American Society for Testing and Materials (ASTM) laboratory tests for determination of flash points and fire points, water by centrifuge, water by distillation, and viscosity at room temperature. Results indicate a decrease in thermal efficiency and an increase in exhaust ...

Science.gov (United States)

PMID:2042311

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This paper discusses the development of a model for the simulation of these stochastic loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Streamtube analysis is employed, which includes the effects of wind shear. Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. Calculations are presented for the VAWT 34-m Test Bed currently being assembled at Bushland, Texas. Time histories of the loads, as well as their Fourier spectra, are presented and discussed. An unexpected finding is that the average output power is predicted to be more sensitive to ...

Energy Technology Data Exchange (ETDEWEB)

In the context of the research project, the physical basis of the direct decoupling of highly concentrated solar radiation in materials without the detour via absorbing heat exchanger walls was examined. Also, the first chemical processes suitable for the effective long-term storage of solar energy were analysed, relevant experiments were carried out and the necessary receiver techniques for high temperature applications were provided. The principle of direct coupling was examined on fluidized beds on the one hand and on cavity receivers, on the other hand. The contribution shows the results achieved in detail. It is recorded that first processes for storing solar energy in chemical reactions were able to be examined. Alkaline earth hydroxides accommodated in ceramic honeycomb structures seem to be possible as stores for medium temperature ranges around 500deg C. Investigations on receiver structure materials are also making progress. Highly transparent, high ...

Energy Technology Data Exchange (ETDEWEB)

Currently, high temperature filter systems are in the demonstration phase with the first commercial scale hot filter systems being installed on integrated gasification combined cycle (IGCC) and pressurized fluid bed combustion cycle (PBFC) systems (70 MW). They are dependent on the development of durable and economic high temperature filter systems. These filters are mostly ceramic tubes or candles. Ceramic filter durability has not been high. Failure is usually attributed to mechanical or thermal shock: they can also undergo significant changes due to service conditions. The overall objective of this project is to commercialize weldable, crack resistant filters which will provide several years service in advanced power processes. The specific objectives of this project are to develop corrosion resistant alloys and manufacturing processes to make Iron Aluminide filter media, and to use a ``short term`` exposure apparatus supported by other ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a PEM fuel cell. The analysis of this process requires determination of the effective thermal conductivity as well as the thermal contact resistance associated with the interface between the GDL and adjacent surfaces/layers. In the present study, a custom-made test bed that allows the separation of effective thermal conductivity and thermal contact resistance in GDLs under vacuum and ambient conditions is described. Measurements under varying compressive loads are performed using Toray carbon paper samples with a porosity of 78% for a range of thicknesses. The measurements are complemented by compact analytical models that achieve good agreement with experimental data. A key finding is that thermal contact resistance is the dominant component of the total thermal resistance; neglecting this phenomenon may result in significant errors in ...

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this research work was to prepare hydrocracking catalysts using amorphous silica-alumina (ASA) supports in combination with USY and {beta}-zeolites. Three supports: namely silica-alumina, USY and {beta}-zeolites were selected to prepare the extrudates using AP-1 as a binder, while two metal pairs: namely Ni-W and Ni-Mo were loaded on the extrudates through co-impregnation using incipient wetness technique. The catalysts were then calcined at 550C for 2h. The catalysts were tested in a fixed-bed flow reaction system for their activity, using desulfurized vacuum gas oil (DS-VGO) as a feedstock. The catalytic evaluation results of the catalysts showed that {beta}-zeolite alone and in combination with the ASA used in this study, has a potential as a support for developing heavy oil hydrocracking catalysts. A balance of weak and strong acidities of {beta}-zeolite provides control cracking, while high surface area and bigger ...

British Library Electronic Table of Contents (United Kingdom)

Cobalt supported on Beta zeolite catalysts were prepared by impregnation of metal salts in aqueous solution and were tested for the Fischer Tropsch reaction. The support consisted of a Beta zeolite composed by crystallites of nanometric dimensions and a SiO2/Al2O3 molar ratio of about 50. This support was impregnated with Co(NO3)2 aqueous solution using different metal loads of 7.5, 10, 15 and 20wt% Co. These materials were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), N2 adsorption (BET), thermal programmed reduction (TPR) and FTIR of adsorbed pyridine (i.e., surface acid sites distribution). All the catalysts showed a significant catalytic activity for the F-T reaction from synthesis gas (CO+2H2), in a continuous fixed bed reactor sys...

Energy Technology Data Exchange (ETDEWEB)

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained during the operation of mixer pumps in tank 241-AZ-101. The primary purpose of the mixer pump test (MPT) is to demonstrate that the two 300 horsepower mixer pumps installed in tank 241-AZ-101 can mobilize the settled sludge so that it can be retrieved for treatment and vitrification. Sampling will be performed in accordance with Tank 241-AZ-101 Mixer Pump Test Data Quality Objective (Banning 1999) and Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis (Mulkey 1999). The sampling will verify if current air emission estimates used in the permit application are correct and provide information for future air permit applications.

Energy Technology Data Exchange (ETDEWEB)

0pen ended piles develop internal frictional resistance between the internal soil plug end the pile wall during axial loading. Current pipe pile design practice assumes that the ultimate internal skin friction is of the same order of magnitude as the outer skin friction. This paper describes a series of laboratory pile load tests on instrumented model pipe piles, designed to investigate the development of plug stresses and skin friction along the plug length during pile loading. The piles contain sand columns of various relative densities and of different heights. The soil plugs are loaded to failure under fully drained conditions. The test data indicate that internal skin friction in sand can be substantially higher than assumed in conventional design practice. This finding could lead to significant economical savings on future pipe pile foundations in sand.

Energy Technology Data Exchange (ETDEWEB)

This paper describes the specifications, conceptual design, prototype testing and operating experience of an oil-filled high voltage pulse transmission cable adapted from commercially available air-dielectric RF components. Lawrence Livermore National Laboratory's Advanced Test Accelerator (ATA) requires a method of transmitting 250kV, 70 nanosecond pulses from the power conditioning equipment to the accelerator. The oil-filled cable approach was chosen over alternative concepts because of its high voltage holding capacity, long life and flexibility. The criteria for cable and connector design are discussed. The results of prototype testing and performance of the final design are presented.

International Nuclear Information System (INIS)

This document presents a summary of the work performed in support of the Buried Waste Robotics Program Subsurface Mapping Project. The project objective was to demonstrate the feasibility of remotely characterizing buried waste sites. To fulfill this objective, a remotely-operated vehicle, equipped with several sensors, was deployed at the Idaho National Engineering Laboratory. Descriptions of the equipment and areas involved in the project are included in this report. Additionally, this document provides data that was obtained during characterization operations at the Cold Test Pit and the Subsurface Disposal Area, both at the Idaho National Engineering Laboratory's Radioactive Waste Management Complex, and at the Idaho Chemical Processing Plant. The knowledge gained from the experience, that can be applied to the next generation remote-characterization system, is extensive and is presented in this report.

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a two-stage process proposed as an alternative for the combustion of carbonaceous materials, such as natural gas or coal gas, for almost complete CO{sub 2} capture. In the reduction stage, the structural oxygen contained in the lattice of a reducible inorganic oxide, is used for combustion of the carbonaceous material. In the regeneration stage the oxygen carrier, found in a reduced state after the reduction stage, is regenerated with pure air to recover the physical and chemical properties of the carrier, ready to reinitiate a new cycle reduction-regeneration. In a typical multicycle reactor test, the carriers are subjected to accumulative chemical and thermal stresses and the performance will, probably, decay progressively with the number of cycles. The occurrence of some side reactions may limit the efficiency of the overall process in CO{sub 2} capture. In this paper, titania-supported iron oxides with different iron loadings have ...

Energy Technology Data Exchange (ETDEWEB)

Plans for the disposal of radioactive liquid and solid wastes presently stored in double-shell tanks at the Hanford Site call for retrieval and processing of the waste to create forms suitable for permanent disposal. Waste will be retrieved from a tank using a submerged slurry pump in conjunction with one or more rotating slurry jet mixer pumps. Pacific Northwest Laboratory (PNL) has conducted tests using simulated waste slurries to assess the effects of a impinging slurry jet on the corrosion rate of the tank wall and floor, an action that could potentially compromise the tank`s structural integrity. Corrosion processes were investigated on a laboratory scale with a simulated neutralized cladding removal waste (NCRW) slurry and in a subsequent test with simulated neutralized current acid waste (NCAW) slurry. The test slurries simulated the actual NCRW and NCAW both chemically and ...

Energy Technology Data Exchange (ETDEWEB)

The LANL Environmental Restoration (ER) Program Office, established in October 1989, is faced with the challenge of assessing and cleaning up nearly 1,8000 potentially hazardous waste sites according to an aggressive corrective action schedule that the Environmental Protection Agency (EPA) mandated on May 23, 1990, in a Resource, Conservation, and Recovery Act (RCRA) Part B Permit. To maximize program efficiency, the ER Program Office will implement a unique management approach designed to maximize the use of laboratory technical expertise. The Installation Work Plan, which provides a blueprint for the program, has been submitted to EPA for review and approval. A work plan for characterization of Technical Area 21, an early plutonium processing facility, is also nearing completion. The feasibility of an expedited cleanup of the Laboratory's worst hazardous waste release has been modelled using a computer code originally developed by ...

International Nuclear Information System (INIS)

Environmental research related to uranium tailings is being carried out within the Mining Research Laboratories and Mineral Sciences Laboratories of CANMET, EMR. Field-related research on uranium tailings has been conducted at Elliot Lake for over five years. Much of the work has been focused on a program to rehabilitate pyritic tailings. This has resulted in developing a practicable technology for growing vegetation on such wastes. Limitations have been small size of the test-plots and the relatively short period during which experiments have been carried out. A research program aimed at identifying and reducing acidic and radioactive effluents is also underway at Elliot Lake. These liquid effluents have been identified as the most serious threat to the environment. Research at the Mineral Sciences Laboratories and its predecessor divisions relating to the processing of uranium and thorium ores is ...

Energy Technology Data Exchange (ETDEWEB)

This study of the hydrogeology of Chicken Creek Canyon wasconducted by the Environmental Restoration Program (ERP) at LawrenceBerkeley National Laboratory (LBNL). This canyon extends downhill fromBuilding 31 at LBNL to Centennial Road below. The leading edge of agroundwater tritium plume at LBNL is located at the top of the canyon.Tritium activities measured in this portion of the plume during thisstudy were approximately 3,000 picocuries/liter (pCi/L), which issignificantly less than the maximum contaminant level (MCL) for drinkingwaterof 20,000 pCi/L established by the Environmental ProtectionAgency.There are three main pathways for tritium migration beyond theLaboratory s boundary: air, surface water and groundwater flow. Thepurpose of this report is to evaluate the groundwater pathway.Hydrogeologic investigation commenced with review of historicalgeotechnical reports including 35 bore logs and 27 test pit/trench logsas ...

Energy Technology Data Exchange (ETDEWEB)

A 2-stage cold (non-tritium) PMR system was tested with the ITER mix in61 days of continuous operation. No decrease in performance was observed over the duration of the test. Decontamination factor (DF) was found to increase with decreasing inlet rate. Decontamination factors in excess of 1.4 {times} 10{sup 5} were obtained, but the exact value of the highest DF could not be determined because of analysis limitations. Results of the 61-day test were used to design a 2-stage PMR system for use in tritium testing. The PMR system was scaled up by a factor of 6 and built into a glovebox in the Tritium Systems Test Assembly (TSTA) of the Los Alamos National Laboratory. This system is approximately 1/5th of the expected full ITER scale. The ITER mix was injected into the PMR system for 31 hours, during which 4.5 g of tritium were processed. The 1st stage had DF = 200 ...

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories contracted with Rockwell International Science Center to perform a series of narrowband, pseudo-random cyclic fatigue tests on sections of 6063-T651 aluminum, Darrius-type, vertical axis wind turbine (VAWT) airfoils. We designed and constructed a load member that was mounted within the frame of a rigid 200-kip servohydraulic, closed-loop test system to hold the VAWT section and permit cantilever bending along the shear centerline of the beam. A computer program was developed to synthesize a narrow band, pseudo-random load history with fixed root mean square (RMS) stress levels at a given bandwidth and central frequency. Six specimens each of two different weld configurations at the flange mounting plate were tested at several RMS stress levels with failure defined as visual observation of a 3-inch-long crack in the VAWT. In order to test at as great a ...

Energy Technology Data Exchange (ETDEWEB)

This document describes the results of accelerated aging tests to determine the long-term effectiveness of selected impoundment liner materials in a uranium mill tailings environment. The study was sponsored by the US Department of Energy under the Uranium Mill Tailings Remedial Action Project. The study was designed to evaluate the need for, and the performance of, several candidate liners for isolating mill tailings leachate in conformance with proposed Environmental Protection Agency and Nuclear Regulatory Commission requirements. The liners were subjected to conditions known to accelerate the degradation mechanisms of the various liners. Also, a test environment was maintained that modeled the expected conditions at a mill tailings impoundment, including ground subsidence and the weight loading of tailings on the liners. A comparison of installation costs was also performed for the candidate liners. The laboratory ...

Science.gov (United States)

Processes for the hydrogenation of carbon monoxide have had commercial importance since about 1920, when the commercial production of methanol and higher alcohols on oxide catalysts began. Soon thereafter Fischer and Tropsch discovered that liquid hydrocarbons could be synthesized from carbon monoxide and hydrogen over Group VIII metal catalysts. Following extensive catalyst and process development efforts, this technology provided Germany with a source of liquid fuels during World War II. The period following the war saw an acceleration in research and development on the Fischer-Tropsch process, but the only commercial application that was to emerge was the SASOL process in the Union of South Africa. The oil crises of the 1970s have rekindled worldwide interest in indirect liquefaction technologies for the production of clean, high-quality motor fuels from coal. The development of more efficient coal gasification processes and the advent of molecular sieve catalysts that allow ...

Science.gov (United States)

This is the first of a series of monthly reports summarizing the status of the work of the National Accelerator Laboratory. This first report will cover developments since the publication of the Design Report in January. Authorization hearings were held before the Joint Committee on Atomic Energy on February 21, 1968. Dr. Wilson described the plans and designs of the Laboratory. The present plan of the Laboratory is that the Village of Weston will be utilized for office, laboratory, and shop space during construction. The Laboratory business office is already occupying several houses. The linac section is occupying three houses for offices and construction of an 8,000 sq ft laboratory building for linac work is almost complete. Another house is being used and a 4,500 sq ft inflatable building is being constructed for model-magnet and vacuum ...

Energy Technology Data Exchange (ETDEWEB)

A literature review on gasification of lignocellulosic biomass in various types of fluidized bed gasifiers is presented. The effect of several process parameters such as catalytic bed material, bed temperature and gasifying agent on the performance of the gasifier and quality of the producer gas is discussed. Based on the priorities of researchers, the optimum values of various desired outputs in the gasification process including improved producer gas composition, enhanced LHV, less tar and char content, high gas yield and enhanced carbon conversion and cold gas efficiency have been reported. The characteristics and performance of different fluidized bed gasifiers were assessed and the obtained results from the literature have been extensively reviewed. Survey of literature revealed that several industrial biomass gasification plants using fluidized beds are currently conducting in ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the research conducted during Budget Period One on the project ''Improved Natural Gas Storage Well Remediation''. The project team consisted of Furness-Newburge, Inc., the technology developer; TechSavants, Inc., the technology validator; and Nicor Technologies, Inc., the technology user. The overall objectives for the project were: (1) To develop, fabricate and test prototype laboratory devices using sonication and underwater plasma to remove scale from natural gas storage well piping and perforations; (2) To modify the laboratory devices into units capable of being used downhole; (3) To test the capability of the downhole units to remove scale in an observation well at a natural gas storage field; (4) To modify (if necessary) and field harden the units and then test the units in two pressurized injection/withdrawal gas ...

International Nuclear Information System (INIS)

The results of the laboratory studies performed by CIEMAT with the FEBEX bentonite in the context of WP3.2 of the NF-PRO Project and of the Agreement ENRESA-CIEMAT Anexo V are presented and analysed in this report. They refer to the effect of the hydraulic gradient on the permeability of bentonite, the effect of the thermal gradient on the hydration kinetics of bentonite, and the repercussion of temperature on the hydro-mechanical properties of bentonite (swelling, permeability and water retention capacity). In all the cases the bentonite has been used compacted to densities expected in the engineered barrier of a high-level radioactive waste repository. The existence of threshold and critical hydraulic gradients has been observed, both of them dependent on bentonite density and water pressures. After more than seven years of hydration, the 40-cm high bentonite columns are far from full saturation, the thermal gradient additionally delaying the process, which is ...

Energy Technology Data Exchange (ETDEWEB)

Eaton, in partnership with Oak Ridge National Laboratory and the Electric Power Research Institute (EPRI) has completed a project that applies a combination of wireless sensor network (WSN) technology, anticipatory theory, and a near-term value proposition based on diagnostics and process uptime to ensure the security and reliability of critical electrical power infrastructure. Representatives of several Eaton business units have been engaged to ensure a viable commercialization plan. Tennessee Valley Authority (TVA), American Electric Power (AEP), PEPCO, and Commonwealth Edison were recruited as partners to confirm and refine the requirements definition from the perspective of the utilities that actually operate the facilities to be protected. Those utilities have cooperated with on-site field tests as the project proceeds. Accomplishments of this project included: (1) the design, modeling, and simulation of the anticipatory wireless sensor ...

Energy Technology Data Exchange (ETDEWEB)

Sandia was presented with an opportunity in 1993 to design containers for the long term storage and transport of fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory which were tasked with developing the internal fixturing for the contents. The hardware is being supplied by Allied Signal Federal Manufacturing and Technologies, and the packaging will occur at Mason and Hangar Corporation`s Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required not only a rigorous design capable of meeting the long term storage and transportation requirements, but also resulted in development of a ...

Energy Technology Data Exchange (ETDEWEB)

For light water reactors, loss of coolant is an important point in safety analysis, whereas for gas-cooled reactors the ingress of water into the core region is an incident of safety relevance. The applicability of the computer code system GAMTEREX to pebble beds of spherical high-temperature gas-cooled reactor fuel elements with simulated water ingress is verified by experiment. The measurements were performed at a Siemens-Argonaut reactor, using its ring core as a driver zone for a pebble-bed core in the center of the reactor.

Energy Technology Data Exchange (ETDEWEB)

Direct electric heating by passing an electrical current directly through a bed of adsorbent may prove to be an efficient means of regenerating activated charcoal in continuous and batch adsorption processes. Obvious advantages of this type of regeneration are its almost complete lack of inertia, which makes it possible to reduce the number and dimensions of the adsorbers, and its highly efficient use of energy due to the small number of steps in the conversion of the energy, as well as the reduction of heat losses involved in warming the structure and making up for losses to the surroundings. The authors consider the kinetics of direct electric heating of a stationary bed of activated charcoal not containing adsorbed substances.

Energy Technology Data Exchange (ETDEWEB)

During a number of years research and development projects have been made to present methods of monitoring the grate in a grate fired boiler. The monitoring is interesting in order to be able to increase efficiency, increase burn-out of ash, improve the status of emissions, improve transportation of ash and fuel through the furnace, reduce costs for operation and maintenance, handle greater loads etc. Improvement of the combustion has been concentrated to the development of the gas phase combustion. In the past few years the computer development has progressed rapidly and the use of optical monitoring methods have been made possible for monitoring grates. To analyse state of the art of optical grate monitoring systems three different methods have been used, literature search, inquiry where plant owners were asked if they have used grate monitoring systems and if so what experiences they have, and interviews with scientists and users. The inquiry investigation was made during spring ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: A porous media solution PORFLO has been developed for the 3-dimensional two-phase flow by describing the process facility in Cartesian or cylindrical coordinates. The local porosity fraction is applied for distinguishing the fluid filled volumes from the solid structures. The solid structure contribute the two-phase flow through the wall friction, flow area and heat transfer. Optionally the solid structure may contain primary liquid of steam generators, steam in the higher temperature and pressure to be condensed or electrical heating power. By using these optional boundary conditions three different process facilities have been analysed. The thermohydraulic solution based on 5-equation approach, where the conservation equations are solved for the liquid and gas (vapour) mass, mixture momentum (giving the velocity only for the mixture), liquid and gas energy, is described shortly. In addition to that the principles modelling optional boundary ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this research was to determine improved thermal, epithermal, and fast fluxes and several responses at mechanical test surveillance location keys 2, 4, 5, and 7 of the pressure vessel of the Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) for the beginning of the fuel cycle. The purpose of the research was to provide essential flux data in support of radiation embrittlement studies of the pressure vessel shell and beam tubes at some of the important locations.

International Nuclear Information System (INIS)

Axial offset anomaly (AOA) is caused by the deposition of crud on the fuel cladding of a PWR. When significant levels of crud build up on the cladding, boron can accumulate in the pores of the crud as a concentrated solution or solid phase, and cause the flux depression. Numerous studies have been conducted on the primary water chemistry to reduce the amount of crud in the primary circuit to avoid radioactivity buildup and unexpected power transition in the plant. However, experiments on the crud are restricted in the laboratory because the crud is a highly radioactive material. The objective of this study is to develop a test method for simulating the deposition of crud in a nuclear power plant

CERN Document Server

The refractive index of novel organosilica (nano/micro)material is determined using two methods. The first method is based on analysis of optical extinction efficiency of organosilica beads versus wavelength, which is obtained by a standard laboratory spectrometer. The second method relies on the measurable trapping potential of these beads in the focused light beam (laser tweezers). Polystyrene beads were used to test these methods, and the determined dispersion curves of refractive index values have been found accurate. The refractive index of organosilica beads has been determined to range from 1.60-1.51 over the wavelength range of 300-1100 nm.

Energy Technology Data Exchange (ETDEWEB)

This report covers the gamma detectors, measurement instrumentation, and testing results of a system developed at Los Alamos National Laboratory. This system monitors the process liquid waste streams at the Plutonium Facility (TA-55) for the presence of radioactive contamination. The detectors are at various points on the acid, caustic, and industrial waste lines. Two of the detectors are on the sanitary sewer lines from the facility. A custom interface unit associated with these two detectors furnishes the facility operation center with a notification of the detection of material. All of the detectors furnish measurement information to a central computer system for storage and trending.

International Nuclear Information System (INIS)

As part of the start up of Los Alamos National Laboratory's new tritium-handling facility, the efficiency of a catalytic oxidation tritium decontamination system was investigated using deuterated methane. The tests were performed during the start up of the facility to confirm the operability of the system before introducing tritium and to provide a baseline for comparison. Techniques and instruments normally used for atmospheric tracer experiments using deuterated methane were applied virtually without modification. The sensitivity of this method allowed preliminary checks at the sub-ppm (v/v) level.

Energy Technology Data Exchange (ETDEWEB)

This work describes the development of a synchronous key based on micro controller to the switching of three-phase power transformers, which makes possible the achievement of tests to register the inrush current, and the previous establishment of the instantaneous values of the voltage firstly applied to different phases of the energy process. This key is a value tool to the development electric power system projects and to the teaching and researching activities at the laboratory related to transitory phenomena and electric system protection.

Energy Technology Data Exchange (ETDEWEB)

Stress-rupture strength tests were made of metal steam pipe (12Kh1MF steel) in various conditions, the original, after aging under laboratory conditions (580{degrees}C, 10,000 h), and after long service. It was shown that the more the steel is hardened by heat treatment or cold plastic working in the original condition, the less it hardens in creep. It was established that softening in creep of steel with a moderate yield strength is caused primarily by aging and with a high yield strength by pore formation.

Energy Technology Data Exchange (ETDEWEB)

This paper reports on three series of laboratory experiments designed to test the performance of the Hahn-Noll revenue neutral auction (RNA). An alternative institution, a no-rebate uniform price auction (UPA), is also examined as a benchmark. In these experiments, the RNA markets were little different from UPA markets in terms of either prices or market efficiencies. The two institutions did differ in terms of the distribution of the gains from exchange and of the propensity of bidders to engage in a certain type of overbidding. 25 refs., 13 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

The multicell proportional chambers at the backing calorimeter of the ZEUS experiment at the storage ring HERA are supplied with a gas mixture of Ar/CO[sub 2] by an open gas system. Flow proportional counters with the build-up [sup 55]Fe sources are used as gas system monitoring detectors. The ZEUS experiment is planned to collect data for about 10 years. Therefore, the lifetime of the Ar/CO[sub 2] mixture should be known. In this paper, the results of laboratory tests and preliminary measurements of the aging effects for monitoring counters are presented. ((orig.))

Energy Technology Data Exchange (ETDEWEB)

The coal-fired combined cycle with partial gasification and fluidized bed combustion (PGFBC-CC), also referred to as a hybrid cycle, has advantages of staged energy conversion and utilization, which can attain high thermal efficiency with low emissions. Four kinds of PGFBC-CC are studied in this paper, two based on pressurized fluidized bed combustion (PFBC) and two on atmospheric fluidized bed combustion (AFBC). Thermal performance calculations and parametric analyses were performed. On the basis of the results, from the above analyses, the best integration system for China is suggested. In addition, a preliminary exergetic analysis is carried out for three of the PGFBC-CC variants.

International Nuclear Information System (INIS)

Available in abstract form only. Full text of publication follows: In this study. simulation of carbon dioxide absorption by Sodium Hydroxide solution in a packed bed has been investigated. At first, mass and energy balances were applied around a differential height of the bed. So, the governing equations were obtained. Surface renewal theory by Danckwerts was used to represent the mass transfer operation Finally, by changing the operating parameters like solvent temperature, inlet gas composition pressure and height of the bed, the effect of these parameters on the absorption and the composition of carbon dioxide in exit stream have been investigated. (authors)

Science.gov (United States)

your eye to the SCN in your brain, so that light ... Owls are individuals who go to bed late, like to get up late in the moming. And the moming types, ...

Energy Technology Data Exchange (ETDEWEB)

The effect of air addition on biomass tar conversion in catalytic packed bed crackers was studied using both an isothermal micro reactor and a fluidised bed bench scale biomass gasification set up with down stream tar crackers. The micro reactor was applied for experiments with artificial biomass producer gas containing naphthalene as a model tar compound. Experiments were carried out with inert silica and catalytically active calcined dolomite bed material both with and without air addition. Experimental results with real tar from the fluidised bed bench scale gasification set up were in qualitative agreement with results from the micro reactor experiments. (author)

Energy Technology Data Exchange (ETDEWEB)

Solar thermophotovoltaics (STPV) potentially have high system power efficiency together with other attractive attributes for both space and terrestrial applications. This paper presents a summary of work that has been conducted by NASA Lewis Research Center (LeRC) and McDonnell Douglas Aerospace (MDA). The paper discusses analytical modeling and subsystem testing, laboratory, and field testing that has been conducted. The features which make solar thermophotovoltaics attractive for both space and terrestrial applications are discussed. Based upon these investigations and the work of others, a conceptual design has been formulated, and an estimate of system performance is presented. This estimate indicates a solar thermophotovoltaics system can result in competitive energy costs for the utility electrical market applications and a high power-to-mass ratio for space power applications.

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories manages the US Department of Energy program for slimhole drilling. The principal objective of this program is to expand proven geothermal reserves through increased exploration, made possible by lower-cost slimhole drilling. For this to be a valid exploration method, however, it is necessary to demonstrate that slimholes yield enough data to evaluate a geothermal reservoir, and that is the focus of Sandia`s current research. Sandia negotiated an agreement with Far West Capital, which operates the Steamboat Hills geothermal field, to drill and test an exploratory slimhole on their lease. The principal objectives for the slimhole were development of slimhole testing methods, comparison of slimhole data with that from adjacent production-size wells, and definition of possible higher-temperature production zones lying deeper than the existing wells.

International Nuclear Information System (INIS)

Research was performed to assess the feasibility of barrier membrane substances, for use within mining or associated high risk environments, in restricting the diffusion transport of radon gas quantities. Specific tests were conducted to determine permeability parameters of a variety of membrane materials with reference to radon flow capabilities. Tests were conducted both within laboratory and in-situ emanation environments where concentrations and diffusion flows of radon gas were known to exist. Equilibrium radon gas concentrations were monitored in initially radon-free chambers adjacent to gas sources, but separated by specified membrane substances. Membrane barrier effectiveness was demonstrated to result in reduced emanation concentrations of radon gas within the sampling chamber atmosphere. Minimum gas concentrations were evidenced where the barrier membrane material was shown to exhibit lowest radon permeability ...

International Nuclear Information System (INIS)

The facilities in the Institute for Nuclear Research at Pitesti allow the testing, handling and examination of nuclear fuel and irradiated materials. The most important facilities are the TRIGA Steady State Research and Material Test Reactor and the Post-Irradiation Examination Laboratory (PIEL). The purpose of this work is to determine by post-irradiation examination, the behavior of CANDU fuel, irradiated in 14 MW TRIGA reactor. The fuel was irradiated in power ramp conditions. The results of post-irradiation examination are: - Visual inspection and photography of the outer appearance of sheath; - Profilometry (diameter, bending, ovality) and length measuring; - Determination of axial and radial distribution of the fusion products activity by gamma scanning and tomography; - Microstructural characterization by metallographic and ceramographic analyzes; - Mechanical properties determination. The data obtained from the ...

Science.gov (United States)

Fires in the operating room continue to present a hazard to patients, at times with catastrophic and debilitating results. Recent data from closed claim files reveal oxygen, electrosurgical unit (ESU), and surgical drapes are common components of the fire triangle in the operating room. In this era of biotechnological sophistication, why are surgical drapes flammable? The purpose of this study was to test the flammability of different surgical drape materials and to determine the time to ignition using a bipolar ESU device in 21%, 35%, and 100% oxygen concentrations. Results show that regardless of oxygen concentration surgical drapes, when exposed to close contact with the ESU, are flammable. Time to ignition decreases with increasing concentrations of oxygen as expected. One of the surgical drapes tested was advertised to the hospital as nonflammable. Future research should focus on surgical drape materials and aim to reduce the flammability ...

Science.gov (United States)

A clinical laboratory evaluation was conducted on the Clinitek Auto 2000, the Super Aution Analyzer and the Urotron RL9 for the determination of glucose, protein, pH, blood, ketone-bodies and bilirubin.Precision of the systems was tested using three commercial control urine materials, and reported as the percentage of times the instrument repeats a certain value. Good repeatability was obtained with all the instruments.Accuracy of the systems was evaluated by comparison with quantitative procedures, and to check agreement between methods yielding semi-quantitative and quantitative results, ranges of acceptability were defined, based on the criteria reported in a previous paper [2]. It was then found that 87.5 to 98.9% of results from the Urotron RL9 and the Clinitek Auto 2000 were acceptable. With the Super Aution Analyzer the level of agreement was apparently lower because of the higher number of concentration steps used by this instrument. ...

International Nuclear Information System (INIS)

The article is aimed to design and testing of joystick with force feedback used in direct, human control of lifting device. The paper starts with the basic description of designed and tested by us MR rotary brake. Some initial laboratory investigations results of such brakes are presented. The usage of MR brakes in 2 axis joystick is proposed. Such, built by as joystick, is described. It was used as Human-Machine Interface in active control of lifting device. The designed and built 2 axis manipulator with electrohydraulic drive is described. In the paper, the based on PC with input/output card, control system of mentioned above joystick with MR brake and manipulator is described. Finally the control algorithm is proposed.

International Nuclear Information System (INIS)

Fibre-reinforced-polymer-composite material has been suggested as a bearing material to overcome tribological problems witnessed during the testing of Ram assembly of the 540 MWe fuelling machine at RTD. After successful trials at B-Ram the composite material has been adapted for B-RAM, C-Ram and RDB head at fuelling machines being tested at RTD, Hall 7 and at Tarapur. Laboratory evaluations were also carried out at Tribology Lab RTD to study effect of radiation on the composite. Paper deals with the various aspects of life prediction of this material in term of wear and radiation damage. (author)

Energy Technology Data Exchange (ETDEWEB)

Radon proof barriers are used for lowering of radon transport from the soil into the house and the determination of the radon diffusion coefficient is an important parameter to be determined in order to design the minimal thickness of the radon proof insulation. A method has been developed in our laboratory by using modified Lucas cells connected to a radon source and tightly closed onto the top by the tested membranes whose radon diffusion coefficients are being measured. Solving the time-dependent differential equation for radon diffusion in the membrane for well-defined experimental conditions the effective radon diffusion coefficient of the insulating material can be evaluated by comparing the radon concentration decrease in the cell for the first hours with the well-known radioactive decay. First results obtained in several preliminary tests carried out with a parafilm M barrier and two polyethylene membranes are shown ...