Science.gov (United States)

The purpose of this study was to examine the relationship between histomorphometric variables of cancellous bone structure and ultimate compressive strength (UCS) in the second lumbar vertebra (L2) and to determine whether structural variables in the iliac crest are predictive of the same variables and of UCS in L2. At autopsy, 7.5 mm diameter cores were removed from the iliac crest and from L2 of 29 subjects who had died suddenly without bone disease. Cancellous bone volume (BV/TV, %) was significantly lower in L2 than in iliac crest due to lower trabecular number (Tb.N, per mm) and thickness (Tb.Th, microns). There were significant correlations between iliac crest and L2 for BV/TV, Tb.N and trabecular separation (Tb.Sp, microns), but not for Tb.Th. BV/TV ...

Science.gov (United States)

... slenderness ratio. Equations which determine the ultimate compressive strength of a composite were established. Several ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... Coupon 119 * 52 Probability of Survival Versus Ultimate Compressive Strength for Un-notched Laminate 1 Coupon ipn ...

Science.gov (United States)

Automated Transport. Not Studied in Detail. Earth's Neighborhood. Simplified Infrastructure. Mars. Earth-. Moon L. 1. Gateway. Moon. Earth-Sun L. 2. Science ...

International Nuclear Information System (INIS)

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(#+-#5)% and 90(#+-#5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper is based on research on the combustion ignition dual-fuel engine conducted at the Zhejiang Agricultural University. The properties of compressed biogas, its performance characteristics in the compression ignited dual-fuel engine as well as the possibilities and needs for its use are discussed. Using information derived from experimental data compiled by the laboratory, analyses and comparisons have been made between high- and low-pressure biogas used in the compression ignition dual-fuel engine with respect to variation of power and the corresponding characteristic curve of the engine. The economic effects of utilizing compressed biogas are also discussed. (author).

Science.gov (United States)

... 28 Thickness vs Ultimate Compressive Strength for LM-833 Magnesia. ... Ultimate Tensile Stress (S) = 0. 112 * 0. 012 Ultimate Compressive Strength ...

Science.gov (United States)

Ultimate compressive strength in the longitudinal direction. (3. Ultimate tensile strength in the transverse direction. U'. Ultimate compressive strength in ...

Science.gov (United States)

... been demonstrated in steady compressible flows. ... steady Compressible Flow on an Oscillating Airfoil ... of Oscillating Airfoils", AGARD-CP-552, Aug. ...

Science.gov (United States)

... Abstract : The ultimate compressive strength of Conolon 506 increases from 39,200 psi at +78F to 57,100 psi at -320F. ...

Science.gov (United States)

... ULTRASONIC VIBRATION TO PORTLAND CEMENT-WATER PASTE REDUCES THE ULTIMATE COMPRESSIVE STRENGTH OF MORTARS ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

In 1963, Grover and co-workers at the Los Alamos. Scientific. Laboratory ...... and A. P. Watkins. (1986) "The Computation of Compressible ...

Energy Technology Data Exchange (ETDEWEB)

Diseases of the mandible affect the soft tissues aside from the osseous manifestation. This can be shown clearly and in great detail by magnetic resonance imaging (MRI). MRI is the gold standard in the diagnostic evaluation of any internal derangement of the temporomandibular joint. Dental MRI requires high resolution techniques and in some cases also intravenous administration of contrast material. These techniques allow delineation of the neurovascular bundle. In the past few years new indications were formulated, for example, the evaluation of the integrity of the inferior alveolar nerve in trauma and in radicular cysts. New quantitative methods now enable insights into the pathophysiology. The objective of this review is to communicate accepted indications for MRI of the mandible and to present innovative applications. (orig.) [German] Mandibulaere Erkrankungen beteiligen neben dem Knochen Weichteilstrukturen, die sich mit der MRT klar und detailreich ...

International Nuclear Information System (INIS)

This talk sketches out the main parameters (technology, circuit design) that have an influence on the hardening of digital CMOS integrated circuits. For each technology the more common defects are mentioned. General design rules are proposed to prevent or limit those defects. (D.L.). 2 refs., 2 figs.

International Nuclear Information System (INIS)

An uncertainty decrease is an very important issue for enhancing risk-informed (RI) activities worldwide. Especially, a relatively large uncertainty in a level-2 (L2) PSA risk compared with level-1 internal PSA risk has been a bottleneck problem in the RI application to the extent of a severe accident management. According to the ASME PRA standard in which sources of an uncertainty to capture a category-II RI (= Option 2) capability are listed, an uncertainty analysis which identifies the key sources of an uncertainty and includes sensitivity studies for dominant contributors to LERF (Large Early Release Frequency) needs to be provided. To solve these problems, USNRC have developed the 'SPAR-LERF' model related to the L2 RI application and 'L2 uncertainty assessment and improvement' work is being taken as a main PSA2 topic of the SARNET (Severe Accident Research ...

Energy Technology Data Exchange (ETDEWEB)

Local blood flow in the thigh was measured with /sup 133/Xe clearance technique in eight male distance runners after compression with a foam rubber compress and a standard elastic bandage. Two degrees of compression were tested, and an initial experiment with rested subjects was followed by a similar experiment immediately after running. Maximum compression exerted a cutaneous pressure of 85 (+/- 8) mm Hg and caused an immediate cessation of intra-muscular blood flow in the compressed area. Moderate compression gave a cutaneous pressure of 40 (+/- 5) mm Hg and resulted in a reduction of blood flow by approximately 50%. During compression, there were no significant differences in the blood flow of rested subjects compared to subjects immediately after running. In acute soft tissue injuries, a maximum compression bandage ...

Energy Technology Data Exchange (ETDEWEB)

The longitudinal and transverse dynamics of a heavy ion fusion beam during the drift compression and final focus phase is studied. A lattice design with four time-dependent magnets is described that focuses the entire beam pulse onto a single focal point with the same spot size.

Energy Technology Data Exchange (ETDEWEB)

The improvement of startability achieved by chemical ignition promotion at low temperature was studied theoretically and experimentally in terms of compression ratio and cetane number using a small direct injection diesel engine. The findings are as follows: The compression ratio and cetane number vary almost linearly. When the compression ratio increases by 1, the cetane number decreases by about 9. Since almost the same ignition condition at starting can be achieved by adjusting the number of cranking cycles, there is almost no influence of compression ratio and cetane number on ignition delay. When the soak temperature is -10{sup 0}C and the compression ratio is 18, the influence of the cetane number is almost negligible. Given the same starting time, the influence produced by an increase in compression ratio by 1 is equivalent to the influence produced by a ...

Science.gov (United States)

... The ultimate compressive strength was measured, and values for Young's modulus were calculated from the linear portion of the test curve. ...

Science.gov (United States)

... hydrostatic pressures up to 700 MPa. The effect of pressure on the ultimate compressive strength is shown. The effect of size on ...

International Nuclear Information System (INIS)

The compressive and torsional buckling behavior of carbon nanotube bundles at room temperature is examined with classical molecular dynamics simulation. The critical compressive load and stiffness of a single carbon nanotube in the bundle are found to be similar to those of individual carbon nanotubes. However, the critical torsional moment and stiffness of a single carbon nanotube in the bundle are found to be higher than those of individual carbon nanotubes. In addition, this study demonstrates that van der Waals interactions between the nanotubes in the bundle significantly affect the critical compressive load of the nanotube bundle.

Energy Technology Data Exchange (ETDEWEB)

Equations are derived to permit calculation of the work required for the isentropic compression of a two phase fuel-air mixture. Methanol evaporation during compression is shown to substantially reduce compression work and thereby improve cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. 14 refs.

Energy Technology Data Exchange (ETDEWEB)

The temperature rise induced by shock compression of polymethyl methacrylate (PMMA) was determined from measurements of the electrical resistivity of embedded copper foils. The temperature of the copper was determined from the observed foil resistance and known values of the change in copper resistivity with temperature and shock compression. Temperature values obtained over a stress range from 0.9 to 6.0 GPa are in good agreement with thermocouple measurements reported previously.

Energy Technology Data Exchange (ETDEWEB)

Material test results are presented for the mechanical behavior of Nylon 66 in compression. Static compression modes include direct compression, stress relaxation and creep. Dynamic direct compression results are included. Tests are performed at atmospheric pressure; strain rates range from 10/sup /minus/4/sec to 10/sup 2/sec; temperatures are 20, 65, 110, 150 and 200/degree/C; moisture levels are 0% (dry), 2% and 6% (saturated); true strains to /minus/0.25 are imposed. Our empirical Temperature-Moisture equivalence of 14/degree/C per 1% moisture is discussed with respect to the /open quotes/free volume/close quotes/ concept.

Science.gov (United States)

Internet bandwidth is in high demand, and one way that web sites lower the amount of bandwidth they use is by compressing their site's images. This lowers the amount of bandwidth used, and makes the site load much faster. There are of course many other useful applications for compressed images. Bit Plane Complexity Segmentation (BPCS) digital picture steganography is a technique to hide data inside an image file. BPCS achieves high embedding rates with low distortion based on the theory that noise-like regions in a bit-plane can be replaced with noise-like secret data without discernible loss in image quality. This is possible because the human eye, while very good at distinguishing anomalies in areas of homogenous texture, is bad at distinguishing anomalies in visually complex areas. However, BPCS is not a robust embedding scheme, and any lossy compression usually destroys the data. Wavelet image ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility of using hydrogen as the sole fuel in a direct injection diesel engine was investigated. An air cooled single cylinder Lister ST1 diesel engine was modified to operate as a low-heat-rejection engine for this study. Partially stabilized zirconia ceramic parts were used to shield the combustion space of the engine. Using a compression ratio of 17.9:1 and motoring the test engine at 21000 rpm, a maximum compression temperature of approximately 900 K was achieved. Under these operating conditions, all lubricants tested were found to burn. Lowering the speed to 1450 rpm and the compression ratio to 17.1, lubricant combustion and hot spots were successfully eliminated. The maximum compression temperature, when compression ignition of hydrogen was tried, was in the 800 K range. The corresponding ceramic surface temperature was estimated to reach 600-700 K. Only sporadic ...

Energy Technology Data Exchange (ETDEWEB)

Kevlar 49/epoxy laminates often exhibit substantial material nonlinearity when subjected to bending. This is a consequence of the yeild-like behavior of a Kevlar 49/epoxy lamina in fiber-directed compression. In this paper, analyses that utilize a simple idealization of compressive yielding are described and calculated results for Kevlar 49 reinforced beams and rings are compared with available data. First, results of a finite element analysis of a thin, unidirectionally reinforced ring subjected to diametral compression are presented. This analysis uses beam elements that incorporate linear tensile and elastic-perfectly plastic compressive behavior. Then a method used to analyze quasi-isotropic beams tested in four-point bending is discussed. This finite element analysis uses a layered shell element with a lamina constitutive model that permits elastic-perfectly plastic response to fiber-directed ...

Energy Technology Data Exchange (ETDEWEB)

The effects of compression ratio on the history of the fuel-burning process was investigated in a single-cylinder direct-injection diesel engine. Two compression ratios of 21.4 and 18.5 were studied by using two wide and shallow bowls. The engine was operated at different speeds and overall air-fuel ratios, but with constant start-of-combustion timing at top dead center. The measured cylinder pressure was used to derive fuel-burning rate. At all conditions, the low-compression-ratio bowl had a larger mass of premixed-burned fuel and a higher peak specific fuel-burning rate. The fuel-burning rate in the diffusion-controlled phase of combustion decreased with decreasing compression ratio. The resulting combustion duration became longer at reduced compression ratio, and the difference could be as large as 14 crank-angle degrees. For the engine conditions examined in this study, the ...

Energy Technology Data Exchange (ETDEWEB)

The problem of thermal instability of compressible, electrically conducting couple-stress fluids in the presence of a uniform magnetic field is considered. Following the linearized stability theory and normal mode analysis, the dispersion relation is obtained. For stationary convection, the compressibility, couple-stress, and magnetic field postpone the onset of convection. Graphs have been plotted by giving numerical values of the parameters to depict the stability characteristics. The principle of exchange of stabilities is found to be satisfied. The magnetic field introduces oscillatory modes in the system that were non-existent in its absence. The case of overstability is also studied wherein a sufficient condition for the non-existence of overstability is obtained. (orig.)

International Nuclear Information System (INIS)

The compressive and bending strengths of a local tropical wood (Kapur-Dryobalanop sp.) were improved significantly by suitable impregnation of polymeric monomers (methylmethacrylate, methylmethacrylate - 5% dioxane and vinyl acetate) into the wood cellular structure and subsequent irradiation to form a wood-polymer composite. Statistical analysis revealed a linear relationship between increase in the strengths and the percentage of polymer impregnated. Fractographic analysis of the impact fractured surfaces under the scanning electron microscope showed the nature of the wood-polymer interface, which could account for the increase in the compressive and bending strengths. (author).

Science.gov (United States)

In this project the influence of residual compression stresses on the stress corrosion cracking behaviour of the turbine disc steel 26 NiCrMoV 14 5 (Rp(sub 0.2) = 850 N/mm(sup 2)) was investigated. The residual compression stresses were produced by shot p...

Science.gov (United States)

... 500 ppm, boron increases the 0.2% offset strength; results show that boron doping does not appreciably affect ultimate compressive strength; for 0 ...

Science.gov (United States)

... ERH moisture cesteats are aumharized on Tables 20 and 21. Moisture sorption isotherme are shewn in Figures XXXI and XXXII. 17 Page 33. ...

Science.gov (United States)

Astronaut crew medical officers (CMO) aboard the International Space Station (ISS) receive 40 hours

Science.gov (United States)

Ultimate Compressive Strength of Short Sheet - Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and Stringer ...

Science.gov (United States)

Wit?,-grain ultimate compressive strength of multiply extruded graphite rods made with G-18 flour,. V. 5. " TOTAL n ACCESSIBLE TO Hp AT 2600 psi ...

Science.gov (United States)

The SHARP cannon. Hydrogen is compressed in the tube on top, the gun barrel is on bottom. When Jules Verne wrote in 1865 "From Earth to the Moon" he ...

Science.gov (United States)

The Baldwin-Lomax model is used in many CFD codes because it is quick and easy to implement. In this

Science.gov (United States)

... In fact, for dynamic loading, the ultimate compressive strength can be more than doubled (Bischoff and Perry 1991), whereas the ultimate uniaxial ...

Science.gov (United States)

... 4 maximum aggregate size. The effects of strain rate (up to 2.5 in./in./sec) on ultimate compressive strength were obtained. ...

UK PubMed Central (United Kingdom)

BackgroundPublicly available DNA sequence databases such as GenBank are large, and are growing at an exponential rate. The sheer volume of data being dealt with presents serious...Full Text Available

Science.gov (United States)

... high- lift separated compressible flows over airfoils ... Proceedings AGARD-CP- 515, paper 26, Symposium ... Viscous-inviscid flow matching Analysis of ...

Science.gov (United States)

... 3. Critical constants, and triple point 4. Compressibility isothermE S. Density, molar volume (of a condensed phase) 6. Equations of state, general ...

Science.gov (United States)

Nov 16, 2010 ... In situ observations are usually made point-wise and the problem in using ...... also discussion of adaptive filtering in Section 4.1.2 of the L4_SM ...... L2-SR -265 SMAP shall provide a Level 1C radar sigma-0 product ...

CERN Document Server

We consider a nonlinear reaction-diffusion equation settled on the whole euclidean space. We prove the well-posedness of the corresponding Cauchy problem in a general functional setting, namely, when the initial datum is uniformly locally bounded in L^2. Then we adapt the short trajectory method to establish the existence of the global attractor and, if the space dimension is at most 3, we also find an upper bound of its Kolmogorov's entropy.

Energy Technology Data Exchange (ETDEWEB)

Two extruded magnesium alloys, AZ31 and AZ61 were selected to evaluate the influence of process parameters on the material forgeability. The processing parameters considered for forging magnesium alloys were: compression load in the range 55 KN to 60 KN and forging temperature, in the range of ambient temperature to 300 C. Uniaxial compression tests were conducted to establish the strain-temperature relationship. The influences of process parameters on the microstructure were also evaluated. (orig.)

UK PubMed Central (United Kingdom)

We report for the first time a case of a 54 years old man with a fatal motorcycle accident due to an external bleeding compression of left internal mammary artery graft to the left anterior descending...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This thesis investigates the application of artificial neural networks for the compression of image data. An algorithm is developed using the competitive learning paradigm which takes advantage of the parallel processing and classification capability of neural networks to produce an efficient implementation of vector quantization. Multi-Stage, tree searched, and classification vector quantization codebook design are adapted to the neural network design to reduce the computational cost and hardware requirements. The results show that the new algorithm provides a substantial reduction in computational costs and an improvement in performance.

Energy Technology Data Exchange (ETDEWEB)

Swirling speed in a direct injection diesel engine was measured by a laser doppler velocimeter. Intake port geometry and engine speed were changed as factors affecting the swirling flow to study the distribution of swirling flow speed. The distribution of swirling flow speed changes complicatedly owing to axial nonsymmetry during intake process but becomes simple shape of axial symmetry during compression process after closing intake valve. But if this is assumed as the rigid swirl shape, the difference due to each intake port cannot be expressed but also large error may be possible to appear close to the cylinder wall. The distribution of swirling flow speed during compression process changes similarly, nearly proportinal to engine speed. But the similarity is higher at the middle period in compression process than at the end period in compression period. Axial distribution of local swirling ratio ...

Energy Technology Data Exchange (ETDEWEB)

Suppliers of systems and components for compressed air technique were shown at the Hanover Fair 94 in Hall 5. On about 6000 m{sup 2} floor area, they showed their product range, which covered the whole range of compressed air technique from compressors via equipment for providing and storing the compressed air to compressed air tools. (orig.) [Deutsch] Die Anbieter von Systemen und Komponenten fuer die Drucklufttechnik waren auf der Hannover-Messe `94 in der Halle 5 zu finden. Dort zeigten sie auf rund 6000 m{sup 2} ihre Produktpalette, die von Kompressoren ueber die Geraete zum Aufbereiten und Speichern der Druckluft bis zu Druckluftwerkzeugen reichte und den gesamten Bereich der Drucklufttechnik abdeckte. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This paper describes an innovative use of post-consumer waste HDPE plastic in concrete as a soft filler. A reference concrete was proportioned to have the 28-day compressive strength of 5000 psi (35 MPa). A high-density plastic was shredded into small particles for use in the concrete. These particles were subjected to three chemical treatments (water, bleach, bleach + NaOH) to improve their bonding with the cementitious matrix. The plastic particles were added to the concrete in the range of 0--5% of total mixture by weight. Compressive strengths were measured for each test mixture. The results showed that chemical treatment has a significant effect on performance of the plastic filler in concrete. Of the three treatments used on the plastic, the best performance was observed with the alkaline bleach treatment (bleach + NaOH) with respect to compressive strength of concrete.

British Library Electronic Table of Contents (United Kingdom)

Free form fabrication and high resolution imaging techniques enable the creation of biomimetic tissue engineering scaffolds. A 3D CAD model of canine trabecular bone was produced via micro CT and exported to a fused deposition modeler, to produce polybutylene terephthalate (PBT) trabeculated scaffolds and four other scaffold groups of varying pore structures. The five scaffold groups were divided into subgroups (n=6) and compression tested at two load rates (49?N/s and 294?N/s). Two groups were soaked in a 25??C saline solution for 7?days before compression testing. Micro CT was used to compare porosity, connectivity density, and trabecular separation of each scaffold type to a canine trabecular bone sample. At 49?N/s the dry trabecular scaffolds had a compressive stiffness of 4.94?1.19?MP...

British Library Electronic Table of Contents (United Kingdom)

A testing methodology, which includes the evaluation of free sintering strain, stress-induced dimensional changes, and weight changes, was developed to determine the critical dimensional changes and thermomechanical response during presintering (i.e., before densification). The effects of organic binder burnout, decomposition of phases, and phase changes on the thermomechanical behavior of a ceramic green body, consisting of methylcellulose as a binder, gibbsite, silica, and alumina, were studied. The compressive stress-strain behavior was found to be nonlinear. The average compressive and tensile strengths of the sample at room temperature were -14.5 and 1.06 MPa, respectively. Both the compressive and tensile strengths decrease by two orders of magnitude with the increasing temperature a...

Science.gov (United States)

The bone mineral content of 109 lumbar vertebrae from 36 different subjects was determined by dual photon absorptiometry. The mean age of the subjects was 58.5 years (range, 31 to 79 years). The ultimate strength of the vertebral bodies was determined during axial compression. Bone mineral content and ultimate compressive strength were correlated (r = 0.86) and the strength was found to increase linearly with increasing amounts of bone mineral content. No differences in this correlation were found in the four vertebral levels (L-4) included in the study, but a difference in this correlation was found between specimens taken from male and female subjects. The results make it possible to estimate the strength of a vertebral body from the knowledge of its bone mineral content as determined by dual photon absorptiometry and provide a basis of estimations of normal and abnormal amounts of bone mineral content in the vertebrae of the lumbar spine. ...

Science.gov (United States)

Ni-free shape memory alloys are promising functional materials for medical applications. A newly developed Ti-Mo based shape memory alloy shows superelasticity after thermomechanical treatment. However, the microstructure evolution and precipitation during thermomechanical processes are still not well understood. In the present paper, compressive deformation behavior at a series of temperatures of 298K - 973K and tensile deformation behavior of the alloy after aged at 573K - 973K have been investigated systematically. It is found that the compressive yield stress and ultimate compressive strength change with the deformation temperature. The ultimate tensile strength and yield stress of aged specimens also change with the aging temperature following a non-linear relationship. Microstructures of aged specimens as well as effects of lattice softening and aging-induced precipitates on the deformation behavior have been ...

Energy Technology Data Exchange (ETDEWEB)

The combustion characteristics of a turbocharged natural gas and diesel dual-fuelled compression ignition (CI) engine are investigated. With the measured cylinder pressures of the engine operated on pure diesel and dual fuel, the ignition delay, effects of pilot diesel and engine load on combustion characteristics are analysed. Emissions of HC, CO, NO{sub x} and smoke are measured and studied too. The results show that the quantity of pilot diesel has important effects on the performance and emissions of a dual-fuel engine at low-load operating conditions. Ignition delay varies with the concentration of natural gas. Smoke is much lower for the developed dual-fuel engine under all the operating conditions. (Author)

British Library Electronic Table of Contents (United Kingdom)

This paper deals with steel fiber reinforced concrete mechanical static behaviour and with its classification with respect to fibers content and mix-design variations. A number of experimental tests were conducted to investigate uniaxial compressive strength and tensile strength. Different mixtures were prepared varying both mix-design and fiber length. Fibers content in volume was of 1% and 2%. Mechanical characterization was performed by means of uniaxial compression tests with the aim of deriving the ultimate compressive strength of fiber concrete. Four-point bending tests on notched specimens were carried out to derive the first crack strength and the ductility indexes. The tensile strength of steel fiber reinforced concrete (SFRC) was obtained both from an experimental procedure and b...

British Library Electronic Table of Contents (United Kingdom)

Magnetic resonance (MR) imaging and histopathology were used to diagnose an articular process synovial myxoma in a dog. On MR images, the tumor was characterized by distortion of the left L1-L2 articular process, widening of the articular process joint, and the presence of a mass contiguous with the synovium of the articular process that displaced the spinal cord. The tumor was T2-hyperintense, T1-hypointense, relative to muscle, and had mild contrast enhancement. The MR features of articular process synovial myxoma may be distinct from other diseases of the articular process joint.

CERN Document Server

The existence of a global attractor for the solution semiflow of the extended Brusselator system in the $L^2$ phase space is proved, which is a cubic-autocatalytic and partially reversible reaction-diffusion system with linear coupling between two compartments. The method of grouping and re-scaling estimation is developed to deal with the challenge in proving the absorbing property and the asymptotic compactness of this typical multi-component reaction-diffusion systems. It is also proved that the global attractor is an $(H, E)$ global attractor with the $L^\\infty$ regularity and that the Hausdorff dimension and the fractal dimension of the global attractor are finite. The results and methodology can find many applications and further extensions in complex biological and biochemical dynamical systems.

CERN Document Server

A proposal is made to test Newton's inverse-square law using the perihelion shift of test masses (planets) in free fall within a spacecraft located at the Earth-Sun L2 point. Such an Artificial Planetary System In Space (APSIS) will operate in a drag-free environment with controlled experimental conditions and minimal interference from terrestrial sources of contamination. We demonstrate that such a space experiment can probe the presence of a "hidden" fifth dimension on the scale of a micron, if the perihelion shift of a "planet" can be measured to sub-arc-second accuracy. Some suggestions for spacecraft design are made.

International Nuclear Information System (INIS)

Research highlights: ? Correlations between microstructure and internal stress during Ti anodising are established. ? Large internal compressive stresses are accumulated in the film during anodising upto 12 V. ?A transition from compressive to tensile stress is observed when the cell voltage exceeds 12 V. ? At 40 V, the oxide films consist of two regions with different compositions and microstructures. Crystallisation of amorphous to anatase TiO2 contributes to the compressive stress relaxation. - Abstract: The relationship between the microstructural and internal stress evolution during Ti anodising is discussed. Samples anodised galvanostatically to 12 V and 40 V, corresponding to different stages of the internal stress evolution, were examined by in-plane and cross-section transmission electron microscopy. Electron diffraction patterns have been complemented with stoichiometry data obtained from energy loss near edge ...

UK PubMed Central (United Kingdom)

The objectives of this research are: (1) to assess selected formulation-relevant physical properties of several commercial Feverfew extracts, including flowability, hygroscopicity, compressibility and...Full Text Available

UK PubMed Central (United Kingdom)

In the present work, fast disintegrating tablets of prochlorperazine maleate were designed with a view to enhance patient compliance by direct compression method. In this method mucilage of Plantago...Full Text Available

International Nuclear Information System (INIS)

The possibility to compress and to split laser pulses at their nonlinear optical transmission through semiconductor films was investigated

UK PubMed Central (United Kingdom)

Lumbar epidural anesthesia is useful in a variety of chronic benign pain syndromes, including lumbar radiculopathy, low back pain syndrome, spinal stenosis, and vertebral compression fractures. Given...Full Text Available

Science.gov (United States)

... 4.4+9 4.30 ds~ ;'* Page 24. Table 3 Ultimate Compressive Strength Data Static Dynamic Round Strength Range Strength Range No. Avg Rise 0No. ...

UK PubMed Central (United Kingdom)

The hierarchical arrangement of collagen and mineral into bone tissue presumabley maximizes fracture resistance with respect to the predominant strain mode in bone. Thus, the ability of cortical...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This book contains over 20 selections. Some of the titles are: Continuum damage mechanics studies on the dynamic fracture of concrete; Dynamic compressive strength of cementitious materials; Rate-sensitivity of mode I and mode II fracture concrete; and An impact damage model of concrete.

Science.gov (United States)

... and retrieve an AED until you have performed CPR for about 2 minutes. 3. Carefully place the ... more breaths. The chest should rise. 9. Continue CPR (30 chest compressions followed by 2 breaths, then ...

Science.gov (United States)

The bone mineral areal content and the ultimate compressive strength were determined in 109 lumbar vertebrae from 36 subjects. The bone mineral areal content was related to the number, shape, and localization of the Schmorl's nodes detected in the x-rayed and sectioned vertebral bodies. One type of node, irregular in shape and localization, occurred only in the vertebrae with low bone mineral areal content values and thus in vertebrae with relatively low compressive strength. A second type of Schmorl's nodes, regular in shape and localization, did not reflect any general weakness of the vertebral bodies. PMID:6623194

CERN Document Server

The phase transition is a performance measure of the sparsity-undersampling tradeoff in compressed sensing (CS). This letter reports, for the first time, the existence of an exact phase transition for the $\\ell_1$ minimization approach to the complex valued CS problem. This discovery is not only a complementary result to the known phase transition of the real valued CS but also shows considerable superiority of the phase transition of complex valued CS over that of the real valued CS. The results are obtained by extending the recently developed ONE-L1 algorithms to complex valued CS and applying their optimal and iterative solutions to empirically evaluate the phase transition.

International Nuclear Information System (INIS)

The method of syndrome coding for data compression read out from multiwire proportional chambers that has been previously proposed is generalized in case of its application to registration of the coordinates of events detected. The questions of execution of arithmetic and algebraic operations on the Galois field elements and their hardware implementation are considered. The method of computation is presented of a specialized processor for parallel computing the coordinates of three sparks. The estimate of its speed is equal to 185 ns. Data compression, data selection and coordinate calculations are performed without use of memory elements and timing pulses.

Energy Technology Data Exchange (ETDEWEB)

A method and apparatus for operating a compression ignition engine having a cylinder wall, a piston, and a head defining a combustion chamber. The method and apparatus includes delivering fuel substantially uniformly into the combustion chamber, the fuel being dispersed throughout the combustion chamber and spaced from the cylinder wall, delivering an oxidant into the combustion chamber sufficient to support combustion at a first predetermined combustion duration, and delivering a diluent into the combustion chamber sufficient to change the first predetermined combustion duration to a second predetermined combustion duration different from the first predetermined combustion duration.

Energy Technology Data Exchange (ETDEWEB)

The increase of the compression ratio of Otto carburator engines up to epsilon = 14 was investigated by Audi in its research department at Neckarsulm. The results are presented in three partial reports. Part one describes the Audi fuel method and demonstrates the effects of the main parameters. Part two shows the influence of the current on the combustion by the help of a new measuring method developed by the Institut fuer Physikalische Elektronik at Stuttgart University. Part three provides a theoretical analysis of the data gained in the investigations.

Energy Technology Data Exchange (ETDEWEB)

Micro-compression specimens, 1O-15{mu}m in diameter by 20-30{mu}m in height, were produced from individual parent grains in a polycrystalline U-13at%Nb shape-memory alloy using the focused ion beam (FIB) technique. The specimens were tested in a nanoindentation instrument with a flat diamond tip to investigate stress-strain behavior as a function of crystallographic orientation. The results are in qualitative agreement with a single-crystal accommodation strain (Bain strain) model of the shape-memory effect for this alloy.

Energy Technology Data Exchange (ETDEWEB)

The Heavy-Ion Fusion Sciences Virtual National Laboratory is pursuing an approach to target heating experiments in the Warm Dense Matter regime, using spacecharge-dominated ion beams that are simultaneously longitudinally bunched and transversely focused. Longitudinal beam compression by large factors has beendemonstrated in the Neutralized Drift Compression Experiment (NDCX) with controlledramps and forced neutralization. Using an injected 30-mA K+ ion beam with initialkinetic energy 0.3 MeV, axial compression leading to ~;;50-fold current amplification andsimultaneous radial focusing to beam radii of a few mm have led to encouraging energy deposition approaching the intensities required for eV-range target heating experiments. We discuss the status of several improvements to our Neutralized Drift Compression Experiment and associated beam diagnostics that are under development to reach the necessary ...

Energy Technology Data Exchange (ETDEWEB)

The authors investigate the feasibility of constructing walls and partitions with enhanced heat storage capability from cement blocks permeated with an organic phase change material (pressed stearic acid). The blocks are lightweight, easy to produce and are cured in the same way as cement or concrete. The ratio of components (cement, stearic acid (SA) and water) was optimized with respect to compressive strength. With normal portland cement, the best compressive strength 2.2 MPa was obtained with a ratio C:SA:W of 1:0.8:0.65 (i.e. 32% stearic acid) after 28 days of curing. This was increased to 4.4 MPa when high early strength cement was used, about as strong as Sipporex, lightweight concrete or lightweight clay bricks. As expected, the compressive strength decreased linearly with temperature between 25/sup 0/C and 100/sup 0/C, at a rate of 15 kPa//sup 0/C. The drying shrinkage of the modules was found to be 50% greater ...

Science.gov (United States)

The ability to mechanically reinforce an osteoporotic vertebral body could impede spinal compression fracture and the associated pain and complications. Previous studies have shown that reinforcement of fractured vertebrae with conventional acrylic cement can relieve symptoms and avoid further collapse. In this study, we explored the use of a carbonated apatite cement combined with a minimally invasive injection technique to improve the compressive mechanical properties of cadaveric vertebral bodies. After establishing the biomechanical characteristics of cement formulations intended to have appropriate viscosities, we evaluated the infiltration of the cements into thoracic vertebral bodies using a combined suction-injection technique. The energy-absorption capabilities of the reinforced vertebral bodies were then measured during axial compressive tests and compared with those of nonreinforced vertebrae. The ultimate ...

Energy Technology Data Exchange (ETDEWEB)

Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were filled with steam. Two testing temperatures were employed, each with its own steam condition. These temperatures and steam conditions were 650/sup 0/F with saturated steam (5% liquid, 95% vapor) and 1200/sup 0/F with superheated steam at 2200 psi. The low-cycle fatigue tests were carried out at both 650/sup 0/F and 1200/sup 0/F by cycling the strain between equal tensile and compressive magnitudes until specimen failure or until it was no longer practical to continue the test. The creep-fatigue tests were carried out to failure by cycling the strain in the same fashion as in the low-cycle fatigue tests but with holds imposed at either the peak tensile strain or the peak compressive strain or at both peak tensile and compressive strains in each loading cycle.

Science.gov (United States)

The ultimate compressive strength and modulus of elasticity of femoral cortical bone from adult geese (Anser anser), were determined by sex and by quadrant by compressing small right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The average ultimate compressive strength was 183 +/- 29 MPa. The average modulus of elasticity was 13.2 +/- 3.4 GPa. The bending strength and bending modulus of elasticity were determined by a three point bend test on rectangular prisms which had the approximate dimensions 0.75 mm X 0.75 mm X 25 mm. The average bending strength was 263 +/- 44 MPa while the average bending modulus was 19.6 +/- 3.1 GPa. The calcium content was determined by atomic absorption spectrophotometry and no correlation was found with the mechanical properties. The histology of the cortical bone was examined both quantitatively and qualitatively. A unique type of Haversian bone is described. Goose ...

International Nuclear Information System (INIS)

The present work focuses on the transformation of high-purity Ni powder blends of controlled volume fractions (40 and 60 %) of nanometre-sized (100 nm) and micrometre-sized (544 nm) particles into bulk samples as part of a strategy for producing ultrafine-grained materials usefully exhibiting both strength and ductility. The process involved cold isostatic pressing at 1.5 GPa and sintering. The resulting bulk samples had relative densities near 95 %, were texture-free, and exhibited two different grain size distributions with an average value of 600 #+-# 30 nm. The mechanical properties were investigated by compression and microhardness tests, both at room temperature, and compared to the behaviour of a sample processed from micrometre-sized powder only. Samples prepared from the blends exhibited high yield stresses of 440 and 550 MPa after compression, and they did sustain work hardening. Tests conducted before and after ...

CERN Document Server

Future High Energy Physics experiments will produce unprecedented data volumes (up to 1 GB/s [1]). In most cases it will be impossible to analyse these data in real time and they will have to be stored on durable mostly magnetic linear media (e.g. tapes) for later analysis. This threatens to become a major cost factor for the running of these experiments. Here we present some ideas developed together with the Institute of Computer Graphics, Department for Algorithms and Programming on how this volume and the related cost can be reduced significantly. The algorithms presented are not general ones but aimed in particular to physics experiments data. Taking advantage of the knowledge of the data they are highly superior to general ones (Huffman, LZW, arithmetic coding) both in compression rate but more importantly in speed as to keep up with the output rate to modern tape drives. Above standard algorithms are, however, used after the data have been transferred in a ...

CERN Document Server

Counting is among the most fundamental operations in computing. For example, counting the pth frequency moment has been a very active area of research, in theoretical computer science, databases, and data mining. When p=1, the task (i.e., counting the sum) can be accomplished using a simple counter. Compressed Counting (CC) is proposed for efficiently computing the pth frequency moment of a data stream signal A_t, where 0= 0, which includes the strict Turnstile model as a special case. For natural data streams encountered in practice, this restriction is minor. The underly technique for CC is what we call skewed stable random projections, which captures the intuition that, when p=1 a simple counter suffices, and when p = 1+/\\Delta with small \\Delta, the sample complexity of a counter system should be low (continuously as a function of \\Delta). We show at small \\Delta the sample complexity (number of projections) k = O(1/\\epsilon) instead of O(1/\\epsilon^2). ...

Science.gov (United States)

A method of producing blast furnace coke from bituminous coals, particularly coals having poor coking capacities in which the coal to be carbonized is ground, predried or preheated, mixed with binders, compressed or formed into briquets having small mechanical resistances and charged into oven chambers, is characterized by fine coals or fine coal mixtures having a swelling index in mixture according to DIN 51741, smaller than 7, and preferably, below 6, and comprising more than 50% of poorly or non-baking coal having a content of volatile matter in excess of 30% or less than 20% which coals or coal mixtures are ground up to attain a surface per unit mass, according to DIN 66145, of from 400 cm/sup 2/ to 1200 cm/sup 2/ per gram, with from 3% to 8% by weight of organic binders, compressing the mixture to form it into a briquet at a temperature range of from 70/sup 0/C to 300/sup 0/C and charging the compressed briquet into ...

International Nuclear Information System (INIS)

Spin-polarized angle-resolved sulfur L_2_,_3VV Auger-electron spectra have been recorded for the c(2x2)S/Fe(001) system. The data show the modulation of the sulfur Auger spin polarization as a function of emission angle, which represents an observation of spin-polarized Auger-electron diffraction (SPAED), a potentially powerful tool for the study of local magnetic structure at surfaces, interfaces, and thin films. Theoretical modeling of the SPAED data indicates a large decrease in the magnetization of the top iron layer, suggesting a magnetic poisoning induced by the sulfur overlayer. These findings are independently supported by the observation of a large decrease of secondary electron spin polarization upon sulfur adsorption.

International Nuclear Information System (INIS)

Heusler films with L2_1 and B2 structure are deposited simultaneously on amorphous carbon films, Si(100) surfaces, and in situ cleaved InAs(110) surfaces by coevaporation of Ni and the alloy MnIn. Morphology, structure, and stoichiometry are investigated with transmission-electron microscopy, electron diffraction, and X-ray spectroscopy. The almost perfect lattice match supports highly oriented growth of Ni_2MnIn on InAs, which is proven by electron diffraction under grazing incidence. The electrical resistivity of thin films on Si show metallic behavior. At temperatures of liquid helium point-contact Andreev reflection spectroscopy is performed on films grown on Si(100) and in situ cleaved InAs(110) surfaces yielding spin polarizations comparable to the ones of Fe, Ni, Co, and permalloy (Ni_8_0Fe_2_0).

British Library Electronic Table of Contents (United Kingdom)

Abstract Four stratigraphic sections in the southern part of the Columbia Basin preserve a sequence of aeolian and non-aeolian sediments ranging in age from 943 to >470 14C ka based on accelerator mass spectrometry radiocarbon dating of fossil molluscs, geochemistry of Cascade Mountain-sourced tephra and association with formally recognized pedostratigraphic units (the Washtucna and Old Maid Coulee soils). Study sections are interpreted as representing concurrent deposition of loess and distal Missoula Flood rhythmites in valleys tributary to main drainages backflooded during the Missoula Floods, and formation of carbonate and iron-rich soils. Sediments belong to the formally recognized L-1 and L-2 loess units established for the Palouse loess, which were deposited in the Columbia Basin su...

British Library Electronic Table of Contents (United Kingdom)

Cache locking technique is often utilized to guarantee a tighter prediction of Worst-Case Execution Time (WCET) which is one of the most important performance metrics for embedded systems. However, in Multi-Processor Systems-on-Chip (MPSoC) systems with multi-tasks, Level 2 (L2) cache is often shared among different tasks and cores, which leads to extended unpredictability of cache. Task assignment has inherent relevancy for cache behavior, while cache behavior also affects the efficiency of task assignment. Task assignment and cache behavior have dramatic influences on the overall WCET of MPSoC. This paper proposes joint task assignment and cache partitioning techniques to minimize the overall WCET for MPSoC systems. Cache locking is applied to each task to guarantee a precise WCET. We pr...

Energy Technology Data Exchange (ETDEWEB)

Concentrations of {sup 239+240} Pu and {sup 137} Cs were measured for vertical direction and horizontal direction in seawater collected at 21 locations on the 8 directions near Wolsung nuclear power plant. The inventories of {sup 239+240} Pu and {sup 137} Cs were calculated in seawater column. The concentrations of {sup 239+240} Pu and {sup 137} Cs were in seawater in the range of 8-36 {mu}Bq/L, 2.4-4.5 mBq/L, respectively. The {sup 239+240} Pu concentration increased with depth, however, the {sup 137} Cs concentrations not greatly changed with depth above thermocline.

International Nuclear Information System (INIS)

The formation constants of species formed in the system H"+"+alanine and VO_"2"+alanine have be determined in aqueous solution for 1.0L_2 The protonation constant of the amino group of alanine has been determined using a computer program which employ a least-squares method. The defence of the protonation of alanine and the stability constant of the species on ionic strength are described by a Debby-huckel type equation.

Science.gov (United States)

A control group of geese (Anser anser) on a normal calcium diet for egg laying poultry was compared to egg laying geese on a calcium deficient diet. The ultimate compressive strength and modulus of elasticity of femoral cortical bone from each group were determined by compressing right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The bending strength and bending modulus of elasticity of tibial cortical bone were determined by three point bend tests on rectangular prisms which were approximately 25 mm by 0.8 mm by 0.8 mm. Bone calcium content and eggshell calcium content were determined by atomic absorption spectrophotometry. Blood samples were analyzed for free calcium ion concentration. Histological observations included studies of cross-sectional microradiographs, examinations of cross sections stained by a modified Masson's technique, and a determination of fractional area of voids by quantitative microscopy. The ...

International Nuclear Information System (INIS)

The refrigerant two-phase flows in a capillary tube and a distributor used in a compression-type refrigerator were visualized by real-time neutron radiography. The thermal neutron radiography system of JRR-3M at the Japan Atomic Energy Research Institute was used. In the visualization experiments of the two-phase flow in the capillary tube of 2 mm I.D., a cooled CCD camera was used, and the axial one-dimensional distributions of void fraction were measured. For the distributor, a high sensitivity video camera with a silicone intensified target tube was used. From the visualized images, the refrigerant behaviors in the distributor were clearly shown, and the liquid fraction in each tube was measured. As a result, it was shown that the refrigerant behaviors in the distributor effected the distributing performance of the refrigerant flow.

International Nuclear Information System (INIS)

Hydrostatic weighing was used to measure the pre-melt density of crystalline eutectic mixtures of alkaline metal chlorides of the compositions (mole fractions): 0.605 LiCl + 0.395 CsCl, 0.585 LiCl + 0.415 KCl, 0.297 NaCl + 0.246 KCl + 0.457 CsCl, and 0.348 NaCl + 0.652 CsCl with melting points 598, 628, 753, 763 K, respectively, as a function of temperature. In the same temperature ranges, the compressibility and molar volume of eutectics as well as their sudden change upon melting were estimated. Unusual variations of these properties were revealed near the crystal/liquid phase transition, which were related to local disordering of particle configuration

British Library Electronic Table of Contents (United Kingdom)

The ever increasing fossil fuel usage and cost, environmental concern has forced the world to look for alternatives. Straight vegetable oils in compression ignition engine are a ready solution available, however, with certain limitations and with some advantages as reported by many researchers. A comprehensive and critical review is presented specifically pertaining to straight vegetable oils usage in diesel engine. A detailed record of historical events described. Research carried out specifically under Indian conditions and international research work on the usage of straight vegetable oils in the diesel engine is separately reviewed. Many researchers have reported that straight vegetable oils in small percentage blends with diesel when used lower capacity diesel engines have shown great...

British Library Electronic Table of Contents (United Kingdom)

Noninvasive prediction of vertebral body strength under compressive loading condition is a valuable tool for the assessment of clinical fractures. This paper presents an effective specimen-specific approach for noninvasive prediction of human vertebral strength using a nonlinear finite element (FE) model and an image based parameter based on the quantitative computed tomography (QCT). Nine thoracolumbar vertebrae excised from three cadavers with an average age of 42 years old were used as the samples. The samples were scanned using the QCT. Then, a segmentation technique was performed on each QCT sectional image. The segmented images were then converted into three-dimensional FE models for linear and nonlinear analyses. A new material model was implemented in our nonlinear model being more...

International Nuclear Information System (INIS)

In a seeded high-gain free-electron laser (FEL), where a coherent laser pulse interacts with an ultrarelativistic electron beam, the seed laser pulse can be frequency chirped, and the electron beam can be energy chirped. Besides these two chirps, the FEL interaction introduces an intrinsic frequency chirp in the FEL even if the above-mentioned two chirps are absent. We examine the interplay of these three chirps. The problem is formulated as an initial value problem and solved via a Green function approach. Besides the chirp evolution, we also give analytical expressions for the pulse duration and bandwidth of the FEL, which remains fully longitudinally coherent in the high-gain exponential growth regime. Because the chirps are normally introduced for a final compression of the FEL pulse, some conceptual issues are discussed. We show that to get a short pulse duration, an energy chirp in the electron beam is important.

Energy Technology Data Exchange (ETDEWEB)

The LCLS, a Free-Electron Laser (FEL) designed for operation at a first harmonic energy of 300 eV ({lambda} {congruent} 40{Angstrom}) in the Self-Amplified Spontaneous Emission (SASE) regime, will utilize electron bunches compressed down to durations of <0.5ps, or lengths of <150 {mu}. It is natural to inquire whether coherent radiation of this (and longer) wavelength will constitute a significant component of the total coherent output of the FEL. In this paper a determination of a simple upper bound on the IR that can be generated by the compressed bunches is outlines. Under the assumed operating parameters of the LCLS undulator, it is shown that that IR component of the coherent output should be strongly dominated by the x-ray component.

British Library Electronic Table of Contents (United Kingdom)

In this paper, we develop a batch fuzzy learning vector quantization algorithm that attempts to solve certain problems related to the implementation of fuzzy clustering in image compression. The algorithm's structure encompasses two basic components. First, a modified objective function of the fuzzy c-means method is reformulated and then is minimized by means of an iterative gradient-descent procedure. Second, the overall training procedure is equipped with a systematic strategy for the transition from fuzzy mode, where each training vector is assigned to more than one codebook vectors, to crisp mode, where each training vector is assigned to only one codebook vector. The algorithm is fast and easy to implement. Finally, the simulation results show that the method is efficient and appears...

Energy Technology Data Exchange (ETDEWEB)

We demonstrate experimentally that the route to a jammed state for a set of bi-dispersed frictional disks, subjected to uni-axial compression from a random initial unjammed state, consists of a consolidation state, a fragile jammed state, and finally a rigid jammed state. In the consolidation regime, the pressure on the sides increases very slowly with the packing fraction {phi} and there are no detectable stress chains. In the fragile jammed state, stress chains are visible, the pressure increases exponentially with {phi}, and the fraction of moving disks drops exponentially. Eventually, a final regime where particle displacements are below our resolution and the pressure varies approximately linearly with {phi} is reached. We argue that this scenario is generic for ather mal frictional compressed particles.

Energy Technology Data Exchange (ETDEWEB)

We present the recent results of our research on the high power ultra-fast silicon RF switches. This switch is composed of a group of PIN diodes on a high purity silicon wafer. The wafer is inserted into a cylindrical waveguide under TE{sub 01} mode, performing switching by injecting carriers into the bulk silicon. Our current design uses a CMOS compatible process and the device was fabricated at SNF (Stanford Nanofabrication Facility). 300 ns switching time has been observed, while the switching speed can be improved further with 3-D device structure and faster driving circuit. Power handling capacity of the switch is at the level of 10 MW. The switch was designed for active X-band RF pulse compression systems--especially for NLC, but it is also possible to be modified for other applications and other frequencies.

Energy Technology Data Exchange (ETDEWEB)

Flywheels containing fiber-reinforced composite materials have attributes suitable for vehicular propulsion, indicating the need for rotor designs which are easily manufactured and low in cost. This development goal was pursued in a cooperative effort between Owens-Corning Fiberglas and Lawrence Livermore Laboratory which investigated flywheels made from compression-molded sheet molding compound (SMC). The design resulted from a Lawrence Livermore analysis, with successful fabrication achieved using a procedure developed by Owens-Corning. Details concerning materials selection, rotor fabrication, and testing are discussed. Owens-Corning subsequently initiated a technical/marketing survey to determine current industrial interests in a low-cost flywheel design; precursory information, pertaining to composite flywheels in particular, is described.

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

British Library Electronic Table of Contents (United Kingdom)

Abstract A series of small phosphazene ligands with pendant 6-phenyl-2,2--bipyridyl moieties, namely L1 [N3P3(OPh)5(OPhbpyPh)], L2 [N3P3(biph)2(OPhbpyPh)2], L3 [N3P3(tBubiph)2(OPhbpyPh)2], L4 [N3P3(biph)2(OPhbpyPh)Cl] and L5 [N3P3(biph)2(OPhbpyPh)(OPh)] [OPhbpyPh = 4-(4-phenoxy)-6-phenyl-2,2--bipyridine, OPh = phenoxy, biph = 2,2--oxybiphenyl and tBubiph = 4,4--di-tert-butyl-2,2--oxybiphenyl], have been used to synthesise the new cyclometallated palladium(II) and platinum(II) complexes [(L1-H)PdCl], [(L1-H)PtCl], [(L1-H)(PdCl)2], [(L3-H)(PdCl)2], [(L4-H)PtCl], [(L5-H)PtCl] and the rhenium(I) complex [L5Re(CO)3Cl]. Single-crystal X-ray diffraction analysis was performed on the free ligand L2 and the palladium complexes [(L1-H)PdCl] and [(L3-H)(PdCl)2]. In both PdII complexes, the metal cent...

International Nuclear Information System (INIS)

The upper range of the requirement for methionine plus cystine in healthy adults was proposed in 1985 by FAO/WHO/UNU to be 13 mg.kg body wt-1.d-1. To explore the validity of this estimate, five healthy, young adult men were given for 7 d a diet based on an L-amino acid mixture supplying 13 mg methionine.kg-1.d-1 (87 mumol.kg-1.d-1) without cystine. Constant intravenous infusions of L-[2H3-methyl-1-13C]methionine were given on days 5 and 7 while subjects were in the fed and postabsorptive states, respectively. Estimates were made of methionine oxidation, and daily methionine balance was derived from the intake-oxidation data. For the five subjects, methionine balances were -0.9, +0.7, +3.5, -3.1, and -3.8 mg kg-1.d-1, or -6, +5, +23, -21, and -26 mumol.kg-1.d-1. These findings lead to the conclusion that the upper range of the requirement for methionine plus cystine probably exceeds 13 mg.kg-1.d-1 in healthy young adults. The implications of ...

Energy Technology Data Exchange (ETDEWEB)

This article describes acoustic methods used in the in-service inspection of the dams and peripheral concrete structures of the Toktogul, Kurpsai, and Bratsk hydroelectric and pumped storage plants. The tests were conducted to assess the compression strength, elasticity, and tensile strength of the concretes. Comparative evaluations against drill core studies proved the acoustic methods to be sufficiently accurate in predicting aging behavior and loss of mechanical and physical integrity in the concretes.

International Nuclear Information System (INIS)

The structure of the P-2, S-1 accelerator mode with one step, S-1, on double period, P-2 for systems, described by the Harper mapping as well as by standard mapping, is analyzed. Detailed analysis of stability criteria is given and comparison with the results of numerical analysis is performed. Three-period compression of the P-2, S-1 island is revealed in the standard mapping. Refs. 7, figs. 7.

Energy Technology Data Exchange (ETDEWEB)

This review examines the characteristics of the compression-ignition type of dual-fuel engine and the combustion phenomena that affect these characteristics. The specific areas covered involve normal combustion processes, the nature and origin of engine knock, operation with LNG, and the effect of intake temperature on combustion efficiency and exhaust composition.

Science.gov (United States)

Novel in situ polymerizable liquid three-arm biodegradable oligomeric polyesters based upon glycolic acid (GA), L-lactic acid (LLA), and their copolymers are synthesized and characterized. Injectable and in situ curable polymer neat resins and their composites formulated with bioabsorbable beta-tricalcium phosphate are prepared at room temperature using photo- and redox-initiation systems, respectively. The cured neat resins show the initial compressive yield strength (YCS, MPa), modulus (M, MPa), ultimate compressive strength (UCS, MPa), and toughness (T, kN mm), ranging from 4.0 to 20.1, 201.5 to 730.2, 82.7 to 310.5, and 1.02 to 3.93. The cured composites show the initial YCS, M, UCS and T, ranging from 27.7 to 56.4, 1440 to 4870, 81.6 to 158.9, and 0.94 to 1.97. Increasing GA/LLA ratio increases all the initial compressive strengths of both neat resins and composites. Increasing filler content increases YCS and M but ...

International Nuclear Information System (INIS)

A case of metastatic Ewing's sarcoma to the skull is presented, demonstrating the superiority of magnetic resonance imaging over other imaging modalities to exclude CNS involvement. Precise delineation of different tumor components in extradural location contained in an intact dural rim together with compressed cortex showing no signs of tumorous involvement constituted an MRI appearance allowing us to exclude tumor outgrowth into the brain. (orig.).

Energy Technology Data Exchange (ETDEWEB)

X-ray results on the lattice parameters, molar volume and thermal expansion coefficients of solid ortho-deuterium for the region from 2 K to the melting point are reported. It is found that the thermal expansion of ortho-deuterium crystals, similarly to parahydrogen is essentially anisotropic near the melting temperature. The vacancy density at the triple point is estimated. Some thermodynamic characteristics of ortho-deuterium are calculated and temperature dependences of heat capacity at constant volume, isothermal compressibility and Gruneisen constant are analyzed.

International Nuclear Information System (INIS)

Load-deflection characteristics of alumina and alumino-silicate fibrous blankets were experimentally determined. Load retention and springback capability of combinations of these materials were measured in a 10,000-hour test at surface temperatures of 650 to 1000"0C (1200 to 1832"0F). Experimental results are presented and future testing plans are discussed.

Energy Technology Data Exchange (ETDEWEB)

Firstly, pitting corrosion observed on hold frames in cargo holds of bulk carriers which exclusively carry coal and iron ore has been investigated in detail. It was shown that the shape of the corrosion pits observed on them is a circular cone and the ratio of the diameter to the depth is in the range between 8 to 1 and 10 to 1, which is different from the trend observed for the bottom shell of the oil tanker where the ratio is in the range between 4 to 1 and 6 to 1. Secondly, a series of tensile tests has been conducted to investigate the effect of pitting corrosion on tensile strength of members. It was pointed out that the tensile strength decreases gradually and the total elongation decreases drastically with the increase of the thickness loss due to pitting corrosion. The reduction of the tensile strength of the members with pitting corrosion is larger than that of members with uniform thickness loss in terms of average thickness loss. Thirdly, a series of ...

Energy Technology Data Exchange (ETDEWEB)

PNNL, with cofunding from the Bonneville Power Administration (BPA) and Building Technologies Program, conducted a research and development activity targeted at addressing the energy efficiency goals targeted in the BPA roadmap. PNNL investigated an integrated heating, ventilation and air conditioning (HVAC) system option referred to as the low-lift cooling system that potentially offers an increase in HVAC energy performance relative to ASHRAE Standard 90.1-2004.

International Nuclear Information System (INIS)

The decrease mechanic effect on loads being transported, shock load limiters (dampers) are being widely used today. Usually, the materials having 'stress-strain' diagrams (#sigma#-#epsilon#) of compression with a substantial portion, where #sigma# = const., are used as dampers. Most widely used are dampers made of foam polystyrene having just the same compression diagram. Similar strain diagrams can be enlisted for some porous materials, timber under cross compression, perforated metallic crushers and some others. By selecting damper material, the level of transmitted to the protected object pressures can be varied from several to hundreds MPa. Timber, as being widely used and featuring good technologic properties together with low cost, becomes an attractive material to be used as the limiter of shock loads. This paper presents the results of stress-strain sequoia properties (USA deliverable) and birch properties ...

Science.gov (United States)

A description is given of an automatic liquid nitrogen pumping system. Pamping of liquid nitrogen iato cooling traps up to a predetermined level is achieved by an automatically controlled compressed air system. An impontant feature of the equipment is the ability to switch automatically from an empty liquid nitrogen reservoir to a full one. This allows for a much more flexible operation than in conventional systems where the reservoir has to be replaced manually when empty. (auth)

Energy Technology Data Exchange (ETDEWEB)

Laser-Doppler anemometry was used to investigate mean flow and turbulence fields in a direct injection diesel engine, motored at speeds of 1500, 2250 and 3000 rev/min. Both cycle-resolved and ensemble-averaged measurements were made in the upper part of the cylinder during the inlet and compression strokes. The cycle-resolved measurements in the inlet stroke are discussed in this paper.

International Nuclear Information System (INIS)

We report the discovery of an active galactic nucleus (AGN) pair in the interacting galaxy system IRAS 20210+1121 at z = 0.056. An XMM-Newton observation reveals the presence of an obscured (N _H #approx# 5 x 10"2"3 cm"-"2), Seyfert-like (L _2_-_1_0_k_e_V = 4.7 x 10"4"2 erg s"-"1) nucleus in the northern galaxy, which lacks unambiguous optical AGN signatures. Our spectral analysis also provides strong evidence that the IR-luminous southern galaxy hosts a Type 2 quasar embedded in a bright starburst emission. In particular, the X-ray primary continuum from the nucleus appears totally depressed in the XMM-Newton band as expected in the case of a Compton-thick absorber, and only the emission produced by Compton scattering ('reflection') of the continuum from circumnuclear matter is seen. As such, IRAS 20210+1121 seems to provide an excellent opportunity to witness a key, early phase in the quasar evolution predicted by the theoretical models of ...

British Library Electronic Table of Contents (United Kingdom)

Schiff-base condensation of a equimolar proportion of diacetyl-monoxime monohydrazone and 1-methylimidazole-2-carboxaldehyde in methanol gives rise to the imidazole azine, 3-(1-methylimidazol-2-yl)methylenehydrazonobutan-2-one oxime(HL). Reaction of 1:1 stoichiometric proportion of HL with copper(II)perchlorate hexahydrate in methanol yields a dimeric oximato bridged copper compound, [Cu2L2(H2O)2](ClO4)2 (1). The compound is characterized by C, H and N analyses, FT-IR, ESI?MS, conductivity measurement, UV?Vis spectra and X-ray single crystal diffraction. The title compound (1) crystallizes in the monoclinic space group P21/c with a?=?6.8533 (8), b?=?18.413 (2), c?=?11.7399 (14) ?, ??=?93.685 (2)?, V?=?1478.4 (3) ?3 and Z?=?2. The geometry around each copper center is distorted square pyram...

Energy Technology Data Exchange (ETDEWEB)

The surface enhanced Raman scattering (SERS) spectra of piperidine in silver colloid solution, on roughened silver electrode and on roughened silver electrode modified with silver nanoparticles were studied, and the high-quality SERS spectra of piperidine on roughened silver electrode modified with silver nanoparticles were obtained for the first time. Surface selection rules derived from the EM enhancement model were employed to deduce piperidine orientations on the different surfaces. On the basis of this, two models of piperidine adsorbed on the surface of the silver nanoparticles were built, and DFT-B3PW91/LanL2dz was applied to calculate the Raman frequencies. It proves that, at higher potential values, the piperidine is perpendicularly standing on the roughened silver electrode surface though its lone-electron pair, but in silver colloid solution and on the silver nanoparticles modified silver electrode the piperidine molecular lies flat ...

Energy Technology Data Exchange (ETDEWEB)

The traveling-wave mode in ring lasers is achieved by two methods: by a reversing mirror, and by using an intracavity nonreciprocal device. This paper is devoted to realization of the traveling-wave mode in a mode-locked YAG-Nd ring laser by a method proposed by Tomov et al. This method uses two intracavity Q-switches. In mode-locked operation, pulses are generated that can be considered short compared with the period of modulation T = L/C (where L is the length of the perimeter of the cavity). Analysis shows that if the shift of the switching signals corresponds to the time of travel of a light pulse between Q-switches, the pulse in one direction will pass the Q-switches at instants of zero losses, while losses in the other direction will be maximized for a distance between Q-switches of L/4, and will be zero for a distance L/2. Experimental verification of the proposed method gave unidirectional lasing with an intensity ratio in the two ...

British Library Electronic Table of Contents (United Kingdom)

Expressed sequence tags (ESTs) of the maxillary galea of the silkworm were analyzed to identify proteins involved in food selection systems. From the 1251 redundant genes of the ESTs, we identified 7 odorant-binding protein-like genes (bmObpL), 6 takeout-like genes (bmToL), and 6 chemosensory protein genes (bmCsp). Quantitative RT-PCR analysis indicated that bmObpL1, bmObpL2, bmObpL3, bmObpL5, bmToL1, bmToL3, and bmorCsp15 were predominantly expressed in the larval oral appendages, such as the maxilla, labrum, labium and antenna. Immunocytochemical analysis indicated that the proteins of bmObpL1, bmObpL3, and bmToL1 were localized in the gustatory chemosensilla on the maxillary galea and olfactory sensilla in the antenna. The proteins encoded by bmObpL1 and bmObpL3 were detected in the gus...

Energy Technology Data Exchange (ETDEWEB)

The effects of therapeutic levels of radiation on the axial properties of the primate vertebral column were studied. Seven male rhesus monkeys (Macaca mulatta) were irradiated with a single does of 1300 cGy to the specific lumbar vertebrae of L2, L3, and L4. Three additional animals served as controls. Radiographs were taken before the radiation treatment and just prior to sacrifice to determine density changes in the bone. The animal subjects were sacrificed 105 days following the radiation exposure. Biomechanical testing was completed on lumbar levels 2 and 3 to identify changes in strength characteristics following radiation treatment. Histomorphometric analysis of lumbar vertebrae level 4 was completed to identify volume and surface density changes as well as cellular changes. Tetracycline, dicarbomethylaminomethyl fluorescein (DCAF), and xylenol orange were used as bone labeling agents to aid in the histomorphometry and to obtain dynamic ...

CERN Document Server

In this review, we show how advances in the theory of magnetic pseudodifferential operators (magnetic $\\Psi$DO) can be put to good use in space-adiabatic perturbation theory (SAPT). As a particular example, we extend results of [PST03] to a more general class of magnetic fields: we consider a single particle moving in a periodic potential which is subjectd to a weak and slowly-varying electromagnetic field. In addition to the semiclassical parameter $\\eps \\ll 1$ which quantifies the separation of spatial scales, we explore the influence of additional parameters that allow us to selectively switch off the magnetic field. We find that even in the case of magnetic fields with components in $C_b^{\\infty}(\\R^d)$, e. g. for constant magnetic fields, the results of Panati, Spohn and Teufel hold, i.e. to each isolated family of Bloch bands, there exists an associated almost invariant subspace of $L^2(\\R^d)$ and an effective hamiltonian which ...

International Nuclear Information System (INIS)

Inelastic scattering of 180 MeV #pi#"+ and #pi#"- from "5"2Cr shows an angular distribution for the 2_2"+ state at 2.96 MeV that differs greatly from the usual L = 2 shapes for 2"+ states. This state is perhaps the only case from pion-inelastic scattering in which standard distorted-wave impulse approximation models (including multistep and single-step responses) fail to reproduce the measured angular distribution. Furthermore, this unique excitation has been shown to have the features expected of a seniority-four proton excitation yet the pion data show charge symmetry. While coupled-channel calculations are not able to reproduce the pion data, they do agree with the shape observed for 42 MeV #alpha# particle scattering to this state, but the magnitude of the #alpha# scattering data is not consistent with a collective model and known #gamma# ray deexcitations. Scattering to the first and third 2"+ states of "5"2Cr with pions and #alpha# ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the concluding efforts at the Engineering Sciences Laboratory of TRW on two specific areas of current research activity within the more general context of proposed lean-burn operation of Otto-cycle-type automotive engines. These areas are: (1) achievement of knock-free performance, both under available fuels and current compression ratios and also under higher-octane fuels (e.g., alcohols) and higher-compression-ratio design (for greater thermal efficiency); and (2) identification of counterstrategies for two-wall (crevice-type) quenching of flame propagation, a phenomenon now widely acknowledged to be the major source of unburned-hydrocarbon emissions exhausted from homogeneous-charge cyclinders. There are certainly other highly active areas of research in Otto-cycle engines, such as turbocharging, ignition devices, and valve design, but the two above-cited topics were the topics of this project.

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Utility Applications Program is to provide information and assistance to interested utilities on central station energy storage systems. Compressed air and underground pumped hydroelectric energy storage are the primary technical focus. Smaller utilities are the primary targets of this program, as they may not have resources to track and utilize new energy conservation developments. The program, initiated during this year-long period, consists of a series of tasks integrating and supporting energy storage implementation. Program management and technical coordination activities monitor the wide range of research ongoing both under government support and in industry and provide a locus for dissemination of results. Recently completed DOE demonstration studies provide the central data base and the DOE CAES and UPH Technology Program activities provide another major resource. In addition a UPH preliminary feasibility study in coorination with Central ...

International Nuclear Information System (INIS)

Molar excess volumes, VE, molar excess enthalpies, HE, and speeds of sound, u, of o-toluidine (i) + cyclohexane or n-hexane or n-heptane (j) binary mixtures have been determined over entire range of composition at 308.15 K. Speeds of sound data have been utilized to predict isentropic compressibility changes of mixing, ?SE of (i + j) mixtures. The observed VE, HE and ?SE data have been analyzed in terms of Graph theory. The analysis of VE data by Graph theory reveals that o-toluidine exists as an associated molecular entity and (i + j) mixtures contain 1:1 molecular complex. It has been observed that VE, HE and ?SE values calculated by Graph theory compare well with their corresponding experimental values. The observed data have also been analyzed in term of Flory theory.

Energy Technology Data Exchange (ETDEWEB)

A shock wave appears when the release of accumulated energy is instantaneous. For instance, it accompanies gunpowder explosion, electric discharge, laser beam convergence, collision of high-speed objects, release of high-pressure gas, and supersonic flight. The shock wave research center of Institute of Fluid Science, Tohoku University, is engaged in researches to elucidate the basics of various shock wave phenomena and to apply the fruit to engineering, science, and medicine. In this report, some examples of recent application studies at the center are described, and the trend of shock wave researches in the future is introduced. The ultimate state of the stagnation point of a nozzle flow simulating a reentry into the atmosphere is produced by shock wave compression in a free piston shock tube which is a ground-borne experimental apparatus. Los Alamos National Laboratory, U.S., succeeded in generating metallic hydrogen of a crystalline structure by subjecting ...

Energy Technology Data Exchange (ETDEWEB)

This third conference on small-satellite applications has combined a number of significant and timely presentations on the status, in the US and on the international front, of this emerging industry. Presentations by all of the major Department of Defense activities in this field, including an overview of the ARPA CAMEO multispectral remote sensing satellite program, space activities at the Air Force Phillips Laboratory, and a space systems capabilities overview of the Naval Research Laboratory, are complemented by presentations from several international activities on their accomplishments and progress in the development of remote sensing satellite programs. For example: Spar Aerospace of Canada presented an overview of the progress they have made in establishing a space program through the use of small satellites, and the University of Surrey and Spar Aerospace provided an overview of the application of image compression schemes to imagery obtained from their ...

International Nuclear Information System (INIS)

Entropy generation is equivalent to destruction of available work (exergy). The useful energy is destroyed due to the intrinsic irreversibility associated within thermodynamic systems. Exergy analysis can be used as an effective basis for the development and improvement of systems design not only in the overall perspective but also in the individual component level. Second law analysis provides a useful tool to identify the irreversibility in any thermal system. This study presents the investigation of local and total entropy generation in compressible flow through a diffuser. Air is used as the fluid. Uniform heat flux boundary condition is applied at the wall. Two dimensional solution of velocity and temperature fields are obtained using the CFD code FLUENT. Distribution of entropy generation rate is investigated throughout the volume of the fluid as it flows through the diffuser. Regions of high entropy generation in the diffuser have been predicted. The angle ...

Energy Technology Data Exchange (ETDEWEB)

Composites based on pure gypsum and polyester-styrene resin have been prepared using various doses of gamma radiation. Some physical properties of the prepared composites and the influence of irradiation dose on it have been studied as: compression strength, hardness, thermal decomposition temperature in nitrogen or oxygen, and the change in weight in aqueous solutions with different pH values. The glass transition temperature of the pure polymer and the composites increases with increasing the irradiation dose up to a plateau, and the glass transition temperature of the pure polymer is lower than that of the composites. The irradiation dose does not seem to affect the decomposition temperature of the pure polymer or the composites significantly and the decomposition temperature in presence of nitrogen is higher than that in presence of oxygen. Increasing the irradiation dose leads to an enhancement of the compression strength of the pure ...

International Nuclear Information System (INIS)

In the present study a partial replacement of aggregate with two different ratios of waste rubber (5%, 10%) with the addition of a constant ratio of rice husk ash (RHA), 5% was carried out. The hardened cement mortar used the optimum water of consistency. The specimens were molded into 1 inch cubic moulds .The specimens were first cured for 24 hours, at 100% relative humidity and then cured under tap water for 3, 7 and 28 days followed by irradiation at different doses of gamma irradiation namely 5 and 10 kGy. The physico-chemical and mechanical properties such as compressive strength, total porosity and bulk density were studied for the three types of specimens. The results showed that the values of the compressive strength, bulk density and chemically combined water of the blended cement mortar paste (OPC-RHA) increase ,while blended cement mortar paste with 5% RHA and 5, 10% waste rubber decrease. The results were confirmed by scanning ...

Energy Technology Data Exchange (ETDEWEB)

The tensile and compressive properties as well as LCF and HCF performance of the extruded magnesium alloys AZ31 and AZ80 were determined in extrusion (L) and long-transverse (T) directions. Owing to marked crystallographic textures, both alloys showed pronounced directional mechanical properties in monotonic as well as cyclic loading with strength values in L-direction being significantly superior to those in T-direction. Thermomechanical treatments such as pressing, swaging and rolling were found to increase yield stresses and HCF strengths and to alter the directionality in properties due to textural modifications. To further improve HCF strengths, mechanical surface treatments such as shot peening, roller-burnishing and deep rolling were utilized. The results indicate marked improvements provided that suitable process parameters are used. The improvement of the HCF strengths is explained by the process-induced changes in near-surface dislocation densities and ...

International Nuclear Information System (INIS)

This guide explained the requirements for Off-Road Compression Ignition Engine Emission Regulations established under the Canadian Environmental Protection Act. The regulations are enforced by Environment Canada, which authorizes and monitors the use of the national emissions mark. The regulations prescribe standards for off-road engines that operate as reciprocating, internal combustion engines, other than those that operate under characteristics similar to the Otto combustion cycle and that use a spark plug or other sparking device. The regulations apply to engines that are typically diesel-fuelled and found in construction, mining, farming and forestry machines such as tractors, excavators and log skidders. Four different types of persons are potentially affected by the regulations: Canadian engine manufacturers; distributors of Canadian engines or machines containing Canadian engines; importers of engines or machines for the purpose of sale; and persons not in ...

Energy Technology Data Exchange (ETDEWEB)

Bone metastases at the thoracic and lumbar segment of the spine are usually presented with painful sensation and medullar compression. The treatment is based on the clinical and neurological conditions of the patient and the degree of tumor invasion. In the present study, 32 patients with spinal metastasis of thoracic and lumbar segment were prospectively analyzed. These patients were treated by decompression and internal stabilization followed by radiotherapy or irradiation with external immobilization. The election of the groups was in accordance with the tumor radiotherapy sensitivity, clinical conditions, spinal stability, medullar or nerve compression and patient's decision. The Frankel scale and pain visual test were applied at the moment of diagnosis and after 1 and 6 months. The surgical group had better results with preserving the ambulation longer and significant reduction of pain.(author)

Energy Technology Data Exchange (ETDEWEB)

The first equipment installed at KfK-HDB was a system with a thin-film evaporator. This was later replaced by two vapor compression evaporating units with forced circulation, for evaporation of liquid LAW, and a steam-heated natural circulation evaporator, for evaporation of liquid MAW. Nuclear activities of the Karlsruhe Nuclear Research Center phasing out, the liquid radwaste quantities to be treated have been shrinking accordingly, so that the current system is planned to be replaced by a smaller system with a thin-film evaporator. (orig./HP) [Deutsch] Im Laufe der Jahre wurde die Anlage mit Duennschichtverdampfer durch zwei Bruedenkompressionsverdampfer mit Zwangsumwaelzung fuer die Eindampfung leicht aktiver waessriger Abfaelle und einem dampfbeheizten Naturumlaufverdampfer fuer die Eindampfung mittelaktiver waessriger Abfaelle ersetzt. Mittlerweile sinkt der Abwasseranfall seit Jahren stetig aufgrund der sinkenden Aktivitaeten des Zentrums auf dem Gebiet der ...

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste form increased with brine temperature, and waste forms from brine at the boiling point exhibited a near doubling of ...

International Nuclear Information System (INIS)

Wood plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, and with Okoume (aucoumea klaineana pierre) imported to Syria in large quantities. Three monomer systems; acrylamide, butylmethacrylate, and styrene were used. polymerization was induced at various radiation doses (10, 20, and 30 kGy) to study the role of radiation doses using a "6"0Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength or tensile strength of the obtained wood polymer composites (WPC) were studied. The effect of the additives, sulfuric acid (H"+), N-vinyl pyrrolidone (NVP), trimethyolpropane triacrylate (TMPTA), urea (U), lithium nitrate (LiNo_3), copper sulfate (CuSO_4) and co-additives on monomer system polymerization were also investigated. Methanol, water and water/methanol mixtures were used as the swelling agents. In general, the use of additives and co-additives brought about an enhancement of ...

Energy Technology Data Exchange (ETDEWEB)

Conventional gas-filled high voltage circuit breakers have the disadvantages of needing means to compress the arc-extinguishing gas and means for storing a significant amount of energy for operating the breaker. This invention has the object of providing a circuit breaker which does not need a gas compression means and whose energy of operation is very low. The principle of operation used in this circuit breaker consists of creating an arc voltage higher than that of the network. The difficulty of creating a high enough arc voltage in the SF{sub 6} gas normally used in a circuit breaker is resolved according to the invention by dividing the initial arc into a large number of elementary arcs by means of metal plates. The arc voltage of each elementary arc is from 20 to 40 volts, depending on the type of metal used. In a particular embodiment, the circuit breaker contains means for displacing the arc and giving it a solenoidal form. 11 figs.

Energy Technology Data Exchange (ETDEWEB)

Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial replacement of ...

Energy Technology Data Exchange (ETDEWEB)

This report describes results from emissions testing of a prototype diesel engine, developed by Volvo Truck Corporation of Sweden, which uses pilot injection of diesel fuel for compression ignition of alcohol fuel injection for main combustion. In addition to this dual-fuel engine, emission testing was also conducted on a heavy-duty diesel engine of similar design. Both engines were tested over the 1979 13-mode FTP, or shorter versions of this modal test, and over the 1984 Transient FTP as well as an experimental bus cycle. The dual-fuel engine was characterized with methanol, ethanol and ethanol with 30 percent water (wt %). An oxidation catalyst was also used with methanol and ethanol. Emission characterization included regulated emissions (HC, CO, and NOX) along with total particulate, unburned alcohols, individual hydrocarbons, aldehydes, phenols, and odor. The particulate matter was characterized in terms of particle size distribution, sulfate content, C, H, ...

Science.gov (United States)

This report describes an investigation of the factors affecting disintegration time in the mouth (DTM) of rapidly disintegrating tablets. The relation between DTM and stationary time of upper punch displacement (STP) was examined using a tableting process analyzer (TabAll). Results indicated that the bulk density of mixed excipient powder used for tablet preparation affects both DTM and STP. As the value of bulk density increased, STP became longer and DTM shorter. The results of a combination of granules and powder with or without a drug showed liner relation between apparent volume (reciprocal of bulk density) and DTM (r(2)=0.7332). For a DTM less than 60 s, a formulation with a bulk density greater 0.5 g/mL should be chosen with a compression force of 5 kN. The hardness of tablets could be greater than 3 kg if at least one high-compressibility excipient was used in the formulation. PMID:18804156

CERN Document Server

This paper studies neighbor discovery problem in wireless networks. A novel scheme, called compressed neighbor discovery is proposed, which assigns each node a unique signature and let nodes simultaneously transmit their signatures during the discovery period. The query node then determines, based on the superposition of the signatures, a small number of nodes as its neighbors, out of a large number of nodes in the network. This is fundamentally a sparse recovery problem. Using the proposed scheme, a single frame time suffices to achieve reliable discovery for large networks. This is in contrast to conventional schemes, where each node repeatedly transmits its identity with random delay, so that a receiver can identify each neighbor at least once without collision. Two practical, low-complexity discovery schemes are studied. The first scheme assigns sparse pseudo-random on-off signatures to the nodes, so that each node can listen to the channel during its own ...

Science.gov (United States)

A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-

Energy Technology Data Exchange (ETDEWEB)

A report is given of investigations into the possibility of utilizing red mud from the Bayer process for producing Ferrari cements. On repeated burning at 1450deg C suitable mixtures of red mud with silica and lime form a clinker with a low free lime content from which Ferrari cement can be produced. The average 28-day compressive strengths of cements produced from this clinker are so encouraging that further investigations are appropriate. (orig.).

Energy Technology Data Exchange (ETDEWEB)

It is postulated that a break of a thin-walled pipe does not cause a subsequent break in the pipe in the vicinity of a plastic hinge even when the wall is weakened by a 60 circumferential crack of a depth of 30% of the wall thickness on the tension side. This pipe behavior is the result of plastic buckling in the compression side and applies to pipes of diameter-to-thickness ratio larger than 20. For this type of pipe, the axial strains decrease with increasing diameter-to-thickness ratio in the tension side. As the pipe is only loaded in one direction, there is no cyclic behavior that can trigger a subsequent break. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This report describes initial work on the development of solidification systems for sodium nitrate waste and compacted waste. Sodium nitrate waste has been solidified in three types of materials: polyethylene, polyester-styrene (PES), and latex cement. Evaluations of the properties of the waste form, such as the ANS 16.1 leaching test, water immersion test and compressive strength measurements were performed on the waste forms containing various amounts of sodium nitrate. 9 refs., 9 figs., 7 tabs.

British Library Electronic Table of Contents (United Kingdom)

Residual stresses are present in engineering components as an unintended consequence of manufacturing processes, but they are also deliberately introduced to beneficial effect during surface engineering procedures. Plasma nitriding is a process of particular importance for forming tools and dies, giving significant advantages in wear, and fatigue resistance through the generation of near-surface compressive residual stresses. A precise knowledge of the level and distribution of residual stresses that exist in engineering components is necessary for an accurate design and prediction of a component's fatigue resistance. However, measurement of residual stresses is not always possible, which is especially true for forming tools. Therefore, other methods for residual stress evaluation and pred...

International Nuclear Information System (INIS)

The integrity of helium circulation loop flanged joints has been attracting recent attention as a design problem, in the development of high-temperature facilities incorporating helium loops (e.g., the VRG-50 pilot nuclear facility). Elevated temperatures and pressures, and the radiation environment, impose additional requirements on sealant materials. This applies first and foremost to rubber seals, which have found widespread favor on account of its excellent elasticity, its ability to spontaneously conform to possible changes in the clearance in the seal assembly, and the low compressive stresses developed in the flange joint assembly.

Science.gov (United States)

nsive neutron-absorbing bricks from commercially available CaB/sub 6/ powder. The bricks are 2 x 3 x 5 in., and are strong enough to withstand normal handling. They last indefinitely; the ones described are now 7 years old, used and stored under normal room temperatures and humidities. The procedure is to make a thick, dry mud with the powder and water, followed by compression in a mold at pressures of about 1 ton/in./sup 2/ or more. The bricks are then baked for 2 hours or longer at a temperature of about 750 deg C. (auth)

Science.gov (United States)

Novel lightweight bricks have been produced by sintering mixes of dried water treatment sludge and rice husk. Samples containing up to 20 wt.% rice husk have been fired using a heating schedule that allowed effective organic burn-out. Rice husk addition increased the porosity of sintered samples and higher sintering temperatures increased compressive strengths. Materials containing 15 wt.% rice husk that were sintered at 1100 degrees C produced low bulk density and relatively high strength materials that were compliant with relevant Taiwan standards for use as lightweight bricks. PMID:19596512

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive hydrogen cooling and adapted tanks. Chemical storage by hydrides ...

Energy Technology Data Exchange (ETDEWEB)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a {sup 60}Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used.

International Nuclear Information System (INIS)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a "6"0Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used. (author)

International Nuclear Information System (INIS)

A fiber optic feedthrough module which comprises a metal sleeve, a fiber optic element extending through the sleeve in spaced relation thereto, and a tandem series of centrally-apertured mating annular sealant bodies of thermoplastic material surrounding the fiber optic element and compressed between it and the sleeve. The module is made by first providing a loose subassembly of a plurality of individual but interfitting sealant bodies on the fiber optic element and then inserting this subassembly into a metal sleeve, following by swaging the whole assembly which eliminates clearances and provides sealed interfaces between the various contacting components. (author).

Energy Technology Data Exchange (ETDEWEB)

This specification establishes requirements for design, testing, and quality assurance for electric heaters that will be used to maintain primary Sodium temperature in the Fast Test Facility (FFTF) reactor vessel. The Test Specification (WHC-SD-FF-SDS-003) has been revised to Rev. 1. This change modifies the fabrication of approximately 25 feet of the subject heater using ceramic insulators over the heater lead wire rather than compressed magnesium oxide. Also, 304 or 316 stainless steel can be used for the heater sheath. This change should simplify fabrication and improve the heater operational reliability.

Energy Technology Data Exchange (ETDEWEB)

For the determination of top dead center (TDC) of a running engine a measuring system using microwaves was developed by AEG and Volkswagen AG. The measuring method utilizes the Doppler shift of the microwaves, which were reflected at the up and down moving piston, and the varying resonance properties of the combustion chamber. The system works with a frequency of 61.4 GHz and can be used as well for spark ignition as form compression ignition engines, particularly for direct injection engines. The output signal is symmetrical to TDC. For data acquisition and data processing, i.e. the calculation of the point of symmetry, the computer system FARES is used in a special assembly.

International Nuclear Information System (INIS)

Twenty rheumatoid arthritis (RA) patients with involvement of the cranio-cervical junction (CCJ) were given CT scan. In most cases the myelo-CT technique with the lumbar injection of small quantities of non-ionic contrast medium was adopted; CT easily diagnosed the horizontal and vertical dislocations on the CCJ, the bone strcture lesions and the inflammatory masses. A high frequency of medullary compressions was also found in these patients. Myelo-CT appears to be the technique of choice for the precise definition of the various factors responsible for the neurological complications found in RA of the CCJ.

Energy Technology Data Exchange (ETDEWEB)

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LIQ) or ambient-temperature compressed hydrogen (CH2). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (lower energy requirement for hydrogen liquefaction and reduced evaporative losses). This paper shows an evaluation of the applicability of the insulated pressure vessels for light-duty vehicles. The paper shows an evaluation of evaporative losses and insulation requirements and a description of the current experimental plans for testing insulated pressure vessels. The results show significant advantages to the use of insulated pressure vessels for light-duty vehicles.

Energy Technology Data Exchange (ETDEWEB)

Apparent molar volumes of aqueous methyldiethanolamine and its salt were determined with platinum vibrating tube densitometers over a range of temperatures from 283K=<T=<576K and at pressures from 0.1MPa to 20MPa. Apparent molar heat capacities were obtained using a Sodev Picker flow microcalorimeter at a pressure of 0.1MPa and within the temperature range of 283K=<T=<328K. Apparent molar adiabatic and isothermal compressibilities at a pressure of 0.1MPa were obtained at temperatures from 283K=<T=<313K with speed of sound measurements. The experimental results were extrapolated to infinite dilution to obtain values for the standard partial molar volumes V{sup o}, heat capacities C{sub p}{sup o}, and isothermal compressibilities {kappa}{sub T}{sup o}. The standard partial molar volumes V{sup o} for the neutral amine and its salt show increasingly positive and negative values, respectively, at high ...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), loading collapse ...

Energy Technology Data Exchange (ETDEWEB)

The use of jojoba methyl ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or liquefied petroleum gas (LPG) at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or LPG as the main fuel and jojoba methyl ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic variability data of 100 engine cycles in terms of maximum pressure and its pressure rise rate average and standard ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the development of solidification systems for sodium nitrate waste. Sodium nitrate waste was solidified in the polymers polyethylene, polyester-styrene (PES), and water-extendible polyester-styrene (WEP). Evaluations were made of the properties of waste forms containing various amounts of sodium nitrate by leaching immersion in water, measuring compressive strengths and by the EPA Extraction Procedure. Results of the leaching test are presented as cumulative fraction leached (CFL), incremental leaching rate, and average leaching indices (LI). For waste forms containing 30 to 70 wt% sodium nitrate, the CFL ranged from 9.0 x 10/sup -3/ to 7.3 x 10/sup -1/ and the LI from 11 to 7.8. After ninety days immersion in water, the compressive strengths ranged from 720 psi to 2550 psi. The nitrate releases from these samples using the EPA Extraction Procedure were below 500 ppM. The nitrate releases from PES waste forms were similar ...

Science.gov (United States)

The mechanical properties of metal stents are important parameters in the consideration of stent design, matched to resist arterial recoil and vascular spasm. The purpose of this study was to develop a system for a standardized quantitative evaluation of the mechanical characteristics of various coronary stents. Several types of stents were compressed by external hydrostatic pressure. The stent diameter was assessed by placing a pair of small ultrasonic sono-crystals on the stent. From pressure-strain diagrams the ultimate strength and radial stiffness for each stent were determined. For all stents, except the MICRO-II and the Wiktor stent, the diameter decreased homogeneously until an ultimate compressive strength was exceeded, causing an abrupt collapse. Expanded to 3 mm, the mechanical behavior of the beStent, the Crown and the Palmaz-Schatz stent (PS153-series) were comparable. The spiral articulated Palmaz-Schatz stent showed twice the ...

Energy Technology Data Exchange (ETDEWEB)

Detailed chemical kinetic reaction mechanisms are developed for combustion of all nine isomers of heptane (C{sub 7}H{sub 16}), and these mechanisms are tested by simulating autoignition of each isomer under rapid compression machine conditions. The reaction mechanisms focus on the manner in which the molecular structure of each isomer determines the rates and product distributions of possible classes of reactions. The reaction pathways emphasize the importance of alkylperoxy radical isomerizations and addition reactions of molecular oxygen to alkyl and hydroperoxyalkyl radicals. A new reaction group has been added to past models, in which hydroperoxyalkyl radicals that originated with abstraction of an H atom from a tertiary site in the parent heptane molecule are assigned new reaction sequences involving additional internal H atom abstractions not previously allowed. This process accelerates autoignition in fuels with tertiary C-H bonds in the parent fuel. In ...

Energy Technology Data Exchange (ETDEWEB)

Fully coupled, Newton-Krylov algorithms are investigated for solving strongly coupled, nonlinear systems of partial differential equations arising in the field of computational fluid dynamics. Primitive variable forms of the steady incompressible and compressible Navier-Stokes and energy equations that describe the flow of a laminar Newtonian fluid in two-dimensions are specifically considered. Numerical solutions are obtained by first integrating over discrete finite volumes that compose the computational mesh. The resulting system of nonlinear algebraic equations are linearized using Newton`s method. Preconditioned Krylov subspace based iterative algorithms then solve these linear systems on each Newton iteration. Selected Krylov algorithms include the Arnoldi-based Generalized Minimal RESidual (GMRES) algorithm, and the Lanczos-based Conjugate Gradients Squared (CGS), Bi-CGSTAB, and Transpose-Free Quasi-Minimal Residual (TFQMR) algorithms. Both Incomplete ...

British Library Electronic Table of Contents (United Kingdom)

Paget Schroetter syndrome, or effort thrombosis of the axillosubclavian venous system, is distinct from other forms of upper limb deep vein thrombosis. It occurs in younger patients and often is secondary to competitive sport, music, or strenuous occupation. If untreated, there is a higher incidence of disabling venous hypertension than was previously appreciated. Anticoagulation alone or in combination with thrombolysis leads to a high rate of rethrombosis. We have established a multidisciplinary protocol over 15?years, based on careful patient selection and a combination of lysis, decompressive surgery, and postoperative percutaneous venoplasty. During the past 10?years, a total of 232 decompression procedures have been performed. This article reviews the literature and presents the Exet...

British Library Electronic Table of Contents (United Kingdom)

Two analytical methods were proposed in this research, coupled electro-thermal finite element (FE) analysis and thermal-mechanical FE analysis, to analyze the mechanical behavior of bonding wire of power module under cyclic power loads, and the International Electrotechnical Commission standard is adopted in conducting a power cycling test. The exterior temperature distribution was measured by an infrared thermometer. Moreover, the junction temperature is calculated from the given thermal impedance of the semiconductor chip, chip power loss, and case temperature. Subsequently, the simulated temperature distribution via electro-thermal FE analysis is compared with experimental results to validate the methodology used in the aforementioned analysis. The analysis shows compressive stress at t...

Energy Technology Data Exchange (ETDEWEB)

In an earlier publication we considered acceleration of plasma rings (Compact Torus). Several possible accelerator configurations were suggested and the possibility of focusing the accelerated rings was discussed. In this paper we consider one scheme, acceleration of a ring between coaxial electrodes by a B/sub theta/ field as in a coaxial rail-gun. If the electrodes are conical, a ring accelerated towards the apex of the cone undergoes self-similar compression (focusing) during acceleration. Because the allowable acceleration force, F/sub a/ = kappaU/sub m//R where (kappa < 1), increases as R/sup -2/, the accelerating distance for conical electrodes is considerably shortened over that required for coaxial electrodes. In either case, however, since the accelerating flux can expand as the ring moves, most of the accelerating field energy can be converted into kinetic energy of the ring leading to high efficiency.

Energy Technology Data Exchange (ETDEWEB)

Oxygenated fuels increase fuel consumption due to their low enthalpy of combustion; however, their high antiknock index renders them suitable for use in engines with a high compression rate, increasing their thermal yield. This study evaluated the performance of biorenewable oxygenated fuels (ethanol and isoamyl alcohol) and partially renewable fuels (ETBE: ethyl tert-butyl ether, TAEE: tert-amyl ethyl ether and di-TAE: di-tert-amyl ether) with high degree of purity and in mixtures with automotive gasoline, based on tests with Otto cycle engines. Among the oxygenated fuels evaluated here, di-TAE was found to present the best characteristics of performance, both individually and in mixtures with gasoline. 40 refs., 5 figs., 2 tabs.

International Nuclear Information System (INIS)

The somatic and genetic radiation exposure of patients undergoing Digital Subtraction Angiography (DSA) and traditional Film Arteriography (FA) of cranial, cervical, thoracic and abdominal vascular territories are compared. The radiation doses absorbed within the critical organs - red bone marrow, lung, thyroid gland and female breast - and in the gonads were measured using an anthropomorphic Alderson phantom. A Somatic Dose Index was calculated in order to estimate the somatic radiation risk. The somatic radiation exposure depends upon the location of the critical organs with respect to the entrance site of the x-ray beam, and can be reduced by an appropriate choice of the angiographic projection. Under this condition, the radiation exposure of the patient during DSA can be lower than during FA. For renal DSA an a.p. projection, the use of an abdominal compression device and careful caudal shielding of the field are advocated. (orig.).

Energy Technology Data Exchange (ETDEWEB)

In this article, the ability of artificial neural networks in prediction of separation in steady two dimensional boundary layer flows is studied. Data for network training is extracted from numerical solution of an ODE obtained from Von Karman integral equation with approximate one parameter Pohlhousen velocity profile. As an appropriate neural network, a two layer radial basis generalized regression artificial neural network is used. The results shows good agreements between the overall behavior of the flow fields predicted by the artificial neural network and the actual flow fields for some cases. The method easily can be extended to unsteady separation and turbulent as well as compressible boundary layer flows. (author)

British Library Electronic Table of Contents (United Kingdom)

Post-tensioned (PT) self-centering moment frames have been developed as an alternative to typical moment-resisting frames (MRFs) for earthquake resistance. When a PT frame deforms laterally, gaps between the beams and columns open. However, the gaps are constrained by the columns and the slab in a real PT self-centering building frame. This paper presents a methodology for evaluating the column restraint and beam compression force based on the column deformation and gap openings at all stories. The method is verified by cyclic tests of a full-scale, two-bay by one-story PT frame. Moreover, a sliding slab is proposed to minimize restraints on the expansion of the PT frame. Shaking table tests were conducted on a reduced-scale, two-by-two bay one-story specimen, which comprises one PT frame ...

International Nuclear Information System (INIS)

The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of wood composite materials. (author).

Energy Technology Data Exchange (ETDEWEB)

A micronized de-ashed coal-water slurry (CWS) fuel of approximately 50% coal loading has been successfully ignited and burned in one GE 7FDL engine cylinder at 1050 rpm. For this study, only about one-third of the full load fuel energy was supplied due to limitations of the fuel injection equipment used. Three types of ignition methods have been investigated. They were: Compression ignition with no ignition aid; Separate deisel pilot fuel injection to ignite the CWS fuel; Combined CWS and pilot diesel fuel injection (stratified pilot ignition). Conditions of ignition and the burning characteristics that immediately followed using the above three ignition methods are described.

Energy Technology Data Exchange (ETDEWEB)

This is a process for the manufacture of a filter material for cleaning industrial or internal combustion engine exhaust gases and filter material manufactured according to the process. The filter material is manufactured from the mineralized combustion product of peel of tropical fruits burnt at a temperature of 820/sup 0/C to 840/sup 0/C in an oxidising atmosphere excluding the production of carbon, particularly using banana skins and orange peels, which product is granulated with carrier materials or compressed.

British Library Electronic Table of Contents (United Kingdom)

The present study is focused on preparation of nano composite materials and the effect of citric acid on their different properties. The formation of nano HA and its interaction with chitosan (C), gelatin (G) polymers and citric acid (CA) materials were studied. The Fourier Transformed Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermo-gravimetric analysis (TGA), transmission electron microscope (TEM), and scanning electron microscope (SEM) were used to characterize these composite materials. The compressive strength (CS) was also measured to know the reinforcement of the prepared composites. The results show that carboxylic and amino groups play crucial role for HA formation on chitosan-gelatin polymeric matrix in the presence of citric acid (CA). The formation of nano HA part...

CERN Document Server

A phase transition of gas-liquid type with an upper critical point is examined which arises in a model of charges of one sign on compensating background (OCP). The phase transition parameters are dependent on the detailed assumptions about the compressibility of the background, but the occurrence of this transition is independent on the background equation of state. In the electron-gas model ('jellium'), this transition appears to rule out Wigner crystallization. A variational principle in statistical mechanics is used to derive so-called Double-OCP model for a superposition of two one-component plasma models for charges of opposite sign. The free energy of this model sets an upper bound to that of a real plasma. Situations are discussed where this transition should manifest itself in anomalies in the approximate description of a non-ideal plasma.

British Library Electronic Table of Contents (United Kingdom)

A three-dimensional numerical study is performed to explore the effect of pulsed spanwise-periodic surface thermal perturbation (also denoted as thermal bump) in a Mach 1.5 flat plate laminar boundary layer. A high-resolution upwind-biased Roe method is used with the compressive Van Leer harmonic limiter on a suitably refined mesh. The dependence of flow stability characteristics on the variation of thermal bump geometry (shape and dimension) and pulsing properties (disturbance amplitude and frequency) is assessed. It is shown that the finite-span thermal bumps generate streamwise vortices. When the thermal bump is pulsed, vortex shedding is observed, and the streamwise vorticity grows with the downstream distance. Analysis of the integrated disturbance energy indicates that the streamwise...

Energy Technology Data Exchange (ETDEWEB)

A high pressure piezometer is described with which pVT-measurements on solutions of gases in liquids like oils can be performed at pressures and temperatures up to 2000 bar and 440 K, respectively. The present investigations deal mainly with the system squalaneCO/sub 2/ at different mole fractions, but also with squalaneN/sub 2/. The high accuracy of the measurements reveals a pronounced structure of the pV-curves in dependence on temperature and mole fraction. At larger mole fractions is the unequivocal assignment of the phases ambiguous, and the representation of the experimental data in terms of an equation of state not possible for the whole pressure and temperature range. However, for solutions with lower mole fractions could be determined the saturation pressures and the isothermal compressibility in the unsaturated region. Furthermore, the molar excess volumes of the mixture have been calculated and the phase behaviour has been discussed briefly. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A compression ignition engine was operated on dual fuel principle inducting two commercial fuels and four pure hydrocarbon fuels in turn through intake manifold along with air and injecting diesel fuel to initiate the combustion in the conventional manner. The engine was operated at different loads and at each load the quantity of inducted fuel was increased gradually till knocking set in. The engine performance and exhaust pollutant emissions were recorded at different operating conditions. It was observed that the extent of induction and the effect on the performance depend on the properties of the inducted fuel such as volatility, self ignition temperature and oxidation characteristics. The energy release during the cycle was also observed to shift depending on the properties of inducted fuel. With the dual fuel operation, the thermal efficiency at part loads was observed to be less compared to neat diesel operation. The thermal efficiency reduced with the ...

Energy Technology Data Exchange (ETDEWEB)

The evaluation of calculated values determined by means of the equations given in the TRD 300/301 standard resulted in two nomographs by which it is possible to find the theoretical wall thickness of cylinder shells without cutouts and branches as well as cylinder shells with an inclined or vertical single branch without additional thickening. The equations for the calculation of cylinder shells with an inclined single branch according to TRD 301 having only an iterative solution, the nomographs will be a considerable help for the engineering work. The determination of the theoretical wall-thickness from the nomographs is demonstrated by means of examples.

International Nuclear Information System (INIS)

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 ?m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

CERN Document Server

The Nystrom method is an efficient technique to speed up large-scale learning applications by generating low-rank approximations. Crucial to the performance of this technique is the assumption that a matrix can be well approximated by working exclusively with a subset of its columns. In this work we relate this assumption to the concept of matrix coherence and connect matrix coherence to the performance of the Nystrom method. Making use of related work in the compressed sensing and the matrix completion literature, we derive novel coherence-based bounds for the Nystrom method in the low-rank setting. We then present empirical results that corroborate these theoretical bounds. Finally, we present more general empirical results for the full-rank setting that convincingly demonstrate the ability of matrix coherence to measure the degree to which information can be extracted from a subset of columns.

Energy Technology Data Exchange (ETDEWEB)

High-energy synchrotron x-ray diffraction (XRD) has been used to quantify load transfer in bovine plexiform bone. By using both wide-angle and small-angle XRD, strains in the mineral as well as the collagen phase of bone were measured as a function of applied compressive stress. We suggest that a greater proportion of the load is borne by the more mineralized woven bone than the lamellar bone as the applied stress increases. With a further increase in stress, load is shed back to the lamellar regions until macroscopic failure occurs. The reported data fit well with reported mechanisms of microdamage accumulation in bovine plexiform bone.

International Nuclear Information System (INIS)

Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.

Energy Technology Data Exchange (ETDEWEB)

Dynamic development of new grain boundaries was studied in compression of a magnesium alloy AZ31 with initial grain sizes (D{sub 0}) of 22 {mu}m and 90 {mu}m at a temperature of 673 K. Kink bands are evolved near corrugated grain boundaries and in grain interiors at low strains accompanied with new fine grains. Kink bands are developed often perpendicular to the basal plane. The boundary misorientation of kink band as well as the volume fraction of new grains increases rapidly with increasing strain and approaches a saturation value in high strain. New fine grains are developed faster with decrease in the D{sub 0}. It is concluded that new grain evolution is controlled by a deformation-induced continuous reaction, i.e. continuous dynamic recrystallization (DRX). (orig.)

Energy Technology Data Exchange (ETDEWEB)

The characteristics of the local magnetic shear, a quantity associated with high-mode-number ballooning mode stability, are considered in heliotron/torsatron devices that have a large Shafranov shift. The local magnetic shear is shown to vanish even in the stellarator-like region in which the global magnetic shear is positive. The reason for this is that the degree of the local compression of the poloidal magnetic field on the outer side of the torus, which maintains the toroidal force balance, is reduced in the stellarator-like region of global magnetic shear because the global rotational transform in heliotron/torsatron systems is a radially increasing function. This vanishing of the local magnetic shear is a universal property in heliotron/torsatron systems with a large Shafranov shift since it results from toroidal force balance in the stellarator-like global shear regime that is inherent to such systems.

Energy Technology Data Exchange (ETDEWEB)

Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi{sub 2}-based materials, which are borderline ceramic-intermetallic compounds. MoSi{sub 2} single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi{sub 2} possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi{sub 2}-Si{sub 3}N{sub 4} composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi{sub 2}-based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing.

CERN Document Server

The nucleation and propagation of hydrofractures by injection of over pressured fluids in an elastic and isotropic medium are studied experimentally. Non-Newtonian fluids are injected inside a gelatine whose mechanical properties are assumed isotropic at the experimental strain rates. Linear elastic theory predicts that plastic deformation associated to breakage of gelatin bonds is limited to a small zone ahead of the tip of the propagating fracture and that propagation will be maintained while the fluid pressure exceeds the normal stress to the fracture walls (Ch\\'avez-\\'Alvarez,2008) (i.e., the minimum compressive stress), resulting in a single mode I fracture geometry. However, we observed the propagation of fractures type II and III as well as nucleation of secondary fractures, with oblique to perpendicular trajectories with respect to the initial fracture. In the Video (http://hdl.handle.net/1813/14122) experimental evidence shows that the fracture shape ...