Energy Technology Data Exchange (ETDEWEB)

IMO Momentenlager GmbH of Gremsdorf near Nuremberg produces large rotary bearings for ENERCON wind power systems, preferably for the E-70 and E-82 generators. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Since its establishment as nuclear research plant Juelich in the year 1956, the research centre Juelich (FZJ) is concerned with the material processing of special metals. Among those are, above all, the high-melting refractory metals niobium, molybdenum and tungsten. Electron beam welding has always been considered to be an innovative special welding method; in the FZJ, electron beam welding has, moreover, always been adapted to the increasing demands made by research partners and involved manufacturing and design sectors. From the manual equipment technology right up to highly modern multi-beam technique, the technically feasible for fundamental research has, this way, always been realised. (Abstract Copyright [2007], Wiley Periodicals, Inc.) [German] Das Forschungszentrum Juelich (FZJ) beschaeftigt sich seit seiner Gruendung als Kernforschungsanlage Juelich im Jahr 1956 mit der Materialbearbeitung von Sondermetallen. Hierzu zaehlen vor allem die hochschmelzenden ...

Energy Technology Data Exchange (ETDEWEB)

The multi-spray direct injection diesel engine has the best efficiency of all combustion systems. The optimization of the air-fuel mixture parameters, especially of the fuel injection, enables the forming of the combustion process in a way, that all requirements and legislative regulations concerning power output, noise and exhaust emissions can be fulfilled. Electronic controlled unit injector systems, as developed by Voest-Alpine Automotive GmbH, Linz, offer the necessary potential to meet the complex requirements.

Energy Technology Data Exchange (ETDEWEB)

The demands made on data transmission systems by modern mining companies are used to show why the currently used multiplexers cannot satisfy future requirement. The telecommunications department of Bergbau-Forschung GmbH is now developing a telecommunication system for underground work. The requirements made on this system are reported.

Energy Technology Data Exchange (ETDEWEB)

Melting in a cokeless cupola furnace fuelled with natural gas is a novel, energy-saving and environment-friendly process. In order to be able to monitor the processes inside the furnace with detailed mass and heat balances, an experimental furnace with an efficient measuring system was constructed in the framework of a research project financed by the BMFT and Messrs. Eisenwerke Dueker GmbH und Co. KG, Laufach, Germany. (orig./HS) [Deutsch] Das Schmelzen im kokslosen erdgasgefeuerten Kupolofen ist ein neues, energiesparendes und umweltfreundliches Verfahren. Um die Vorgaenge im Ofen mit umfassenden Stoff- und Waermebilanzen erfassen zu koennen, ist im Rahmen eines vom BMFT und der Firma Eisenwerke Dueker GmbH und Co. KG, Laufach, finanzierten Forschungsvorhabens, ein Versuchsofen mit umfangreicher Messeinrichtung gebaut worden. (orig./HS)

Energy Technology Data Exchange (ETDEWEB)

Surface doping of conjugated polymers is realized by depositing a thin layer of graphene oxide (GO) on top of the polymers. The high proton density and the unique 2D structure of GO facilitate the protonic surface doping of conjugated polymers to achieve high conductivities. This finding represents a new strategy for improving charge transport across the metal/conjugated polymer interface to achieve much improved performance in organic solar cells. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

International Nuclear Information System (INIS)

Arrays of CdS:Mn"2"+:Cu"+ micro- and nanowires grown in polycarbonate ion-track templates exhibit photoluminescence in the spectral domain ranging from 500 to 800 nm at room temperature. A comparison with similar CdS and CdS:Mn"2"+ wire arrays is presented. The individual contributions to the emission spectra of Cu"+ and Mn"2"+ ions in the CdS matrix are explained using their energy level schemes. Also SEM, EDX and EPR data are given for these wires. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

Westinghouse Electric Germany GmbH has developed fluid dynamic models for medium-actuated armatures using the thermal hydraulic code RELAP5 in order to reach a more realistic description of the armature behavior including fluid-structure interactions in case of transient flow conditions in piping systems. The contribution is concerned with the modeling of damped check valves. The model allows the description of the behavior during opening and closure of a check armature. The calculated results show good agreement with the available measured data.

Energy Technology Data Exchange (ETDEWEB)

The physics of microcavities have been a subject of intense study over the past 25 years. This work stimulated a large body of experimental and theoretical work on the optimization of the light extraction properties of light-emitting diodes. Not only has this led to the current high efficiency microcavity LEDs but also to the high brightness LEDs based on other approaches, which are presently available on the market. An overview of the state of the art of planar semiconductor microcavity LEDs will be presented. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

International Nuclear Information System (INIS)

The temperature dependences of the Grueneisen parameter, heat capacity, bulk modulus and linear thermal expansion coefficient of sixteen III-V zincblende compounds are studied by first-principles response-function calculations. The fundamental relationships among these physical parameters are explored. Negative thermal expansions at lower temperature are found in most of these III-V phases except for the nitrides and boron compounds. By analyzing the cell-volume dependences of the phonon spectrum, it is found that the phases with a negative thermal expansion show a significant acoustic phonon weakening at the X-point in their phonon dispersion, while slight weakening is only seen around the L-point for those boron phases. There is no sign of phonon weakening in the nitrides. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

The oil shale PCTM for Modified In Situ Oil Shale Retorting combined with Lurgi Surface Retorting addresses the application of this combination of technologies to the development of oil shale resources in the western United States. This manual describes the combined plant using Lurgi surface retorting technology (developed by Lurgi Kohle and Mineralotechnik GmbH, West Germany) and the Modified In Situ process (developed by Occidental Oil Shale, Inc.) proposed by Occidental Oil Shale, Inc. and Tenneco Shale Oil Company for use in the development of their Federal oil shale lease Tract C-b in western Colorado. Since details regarding waste streams and control technologies for the Lurgi process are presented in a separate PCTM, this document focuses principally on the Modified In Situ process.

Energy Technology Data Exchange (ETDEWEB)

Increasing environmental awareness and new legislation in Europe and, in particular, America have accelerated the development of marketable electric cars which satisfy customer demands in terms of performance, range capability, safety and comfort. Tomorrow's electric cars will therefore require powerful heating and cooling systems for the passenger compartment which meet the conditions specific to this particular mode of transport and which do not overly affect the range capability of such vehicles. At Behr GmbH suitable system concepts were developed at a very early stage which were based on a high proportion of recirculated air, the use of the A/C unit as a heat pump, and heat recovery. This paper will examine two typical A/C systems which combine good heating and cooling characteristics with the low electric power requirement of only 1,5-2 kW. (orig.).

International Nuclear Information System (INIS)

The methods of superconducting device fabrication by lithography and multilevel processing usually require a number of processing steps with lithographic resolution and alignment adequate for the scale of the device be fabricated. As an alternative, the focused ion beam (FIB) microscope is increasingly being used directly to fabricate devices. A major advantage of using a FIB compared to other lithography methods is its flexibility and high resolution. It allows in-situ, milling (#propor to#5 nm at a beam current of 1 pA) to a variety of depths, and imaging (2 nm) of the sample. In this paper we describe our development of junction fabrication techniques using the FIB and their application in creating a range of potential sensor devices and quantum electronics applications. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

International Nuclear Information System (INIS)

The band offsets and subband levels in a double quantum well layer for a 660 nm-Ga_0_._4In_0_._6P/(Al_0_._5Ga_0_._5)_0_._5In_0_._5P quantum well laser are determined by photoreflectance using a 410 nm InGaN laser with current modulation at room temperature. The subband levels are analyzed by numerical calculation of the Schroedinger equation for the layer structure by varying the conduction band offset and compared with the measured photoreflectance spectra. The conduction band offset ratio is determined to be 0.5+0.03. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

Wood is currently having a renaissance as a domestic fuel. Wood pellets, usually about 8 mm in diameter and 40 mm long and produced from sawmill and wood processing residues by pressing without binders, are gaining general acceptance. According to a market analysis of Solar Promotion GmbH, Pforzheim, about 4,800 pellet-fuelled heating systems with automatic fuel supply and with a total thermal capacity of 35 kW are in operation in Germany, and 2000 new ones were installed in 2000. [German] Holz als Brennstoff erlebt in vielen Heizkellern und Kaminen eine Renaissance. Und zwar nicht in Form von Holzscheiten, sondern als kleine Presslinge, meist mit einem Durchmesser von acht und einer Laenge von bis zu 40 Millimetern. Als Abfallprodukt von Saegewerken und Holz verarbeitenden Betrieben werden die so genannten Pellets unter hohem Druck und ohne Bindemittel wie beispielsweise Leim hergestellt. Und dieser neue Brennstoff findet immer mehr Anhaenger. So sind im ...

Energy Technology Data Exchange (ETDEWEB)

For millions of people general noise and especially traffic noise are the main sources of environmental pollution. The increasingly stricter noise pollution abatement limiting values laid down by the law call for motor vehicle noise pollution abatement measures. Within the framework of today`s cost- and performance-oriented automobile and engine development developing engineers are required to reduce noise levels. The present state of the art is described and future possibilities of combustion engine structure-borne noise calculation and optimization are discussed from the point of view of K + P Computerunterstuetzte Strukturanalysen GmbH. (orig.) [Deutsch] Laerm allgemein und dabei speziell wiederum der Verkehrslaerm steht fuer Millionen von Menschen an allererster Stelle der persoenlichen Belastung durch die Umwelt. Zur Minderung der Laermbelastung werden vom Gesetzgeber immer schaerfere Grenzwerte vorgeschrieben, die dazu zwingen, Massnahmen zur ...

Energy Technology Data Exchange (ETDEWEB)

A system of equations describing transient enhanced diffusion of beryllium in InGaAs due to kick-out mechanism or due to formation, migration, and dissociation of the pairs ''beryllium atom-group III self-interstitial'' is proposed and analyzed. Simulation of coupled diffusion of beryllium atoms and self-interstitials in InGaAs during rapid thermal annealing was done for the case of dual implantation. For the experiment under consideration the first ion implantation of phosphorus atoms produced the region of extended defects that led to ''uphill'' diffusion of implanted Be in the defect region and in the vicinity of the surface. The suggested reason of ''uphill'' diffusion could be related to the nonuniform distribution of group III self-interstitials that was formed due to the absorption of point defects on the extended defects and on the surface of a semiconductor. The ...

International Nuclear Information System (INIS)

'Full text:' In Germany, Alloy 800 (high nickel austenitic stainless steel) was modified and qualified for the use as steam generator tubing by Siemens/KWU (now AREVA NP GmbH). The service reliability of Alloy 800 has been demonstrated over a long period of time. 1968 Siemens/KWU decided to use this material for the NPP Stade, which started operation in 1972. The steam generators operating with Alloy 800 tubes have now been in service for more than 30 years. Up to now no PWSCC or secondary-side SCC has been observed in the more than 285,000 tubes installed in Siemens/KWU steam generators (including RSG) in 19 PWRs in Europe. The operating experience will be shown and discussed. During the past regular SG tubing inspections using eddy current testing, a few indications were detected within the tube sheet between upper and lower tube expansion. These indications were limited to the outer tube positions. The number of affected positions is small. Two tubes had been ...

International Nuclear Information System (INIS)

A novel technique is proposed for the growth of an InN film on a GaN/Al2O3(0001) template by radio-frequency plasma-excited molecular beam epitaxy (RF-MBE). The method involves 1) InN growth under an In-rich condition and 2) additional nitrogen radical irradiation after the InN growth under an In-rich condition. Excess In that appeared on the InN surface in the InN growth under an In-rich condition is transformed to InN by the additional nitrogen radical irradiation. The effective V/III ratio is easily controlled by monitoring the intensity in a reflection high-energy electron diffraction (RHEED) pattern. The growth of the InN film by repeating the InN growth under an In-rich condition and the additional nitrogen radical irradiation is also demonstrated. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

The liberalisation of the energy markets requires completely new demands to the information processing procedure of energy supply enterprises. These requirements are to be understood as chances for strengthening of the terms of competition. In the following contribution to this subject the actual status of the concept as converted by the Electricity Supply Company of Halle (Saale) including their departments of district heating, gas and electricity supply will be presented. This concept are comprising all experiences as gathered so far as well as intended further actions to be executed. (orig.) [German] Die Liberalisierung der Energiemaerkte stellt fuer Versorgungsunternehmen voellig neue Anforderungen an die Informationsverarbeitung. Diese Anforderungen sind als Chancen zur Staerkung der Wettbewerbsfaehigkeit zu verstehen. Die Verfasser erlaeutern den aktuellen Stand des in der EVH GmbH Halle (Saale) im Querverbund der Sparten Fernwaerme, Gas und Elektrizitaet ...

International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion solutions upon the coatings formation was recorded. It is confirmed that the reduction of protons leads to the interfacial pH ...

Energy Technology Data Exchange (ETDEWEB)

A Tm{sup 3+}- Ho{sup 3+} -codoped single crystal of monoclinic BaY{sub 2}F{sub 8} has been characterized by means of high resolution FTIR spectroscopy in the wave number range 2000-24000 cm{sup -1} and in the temperature range 9-300 K. The energy level schemes of the two lanthanide ions as determined by the optical absorption spectra is presented, analyzed, and fitted within a single ion Hamiltonian model. The very small energy separation (about 0.6-1.6 cm{sup -1}) measured between the first and second sublevels of the ground state manifolds for both the ions is in line with the theoretical predictions. The impurity-phonon coupling is put into evidence by the thermally induced line shift and broadening, and by the detection of vibronic replicas of a few lines. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

Beside sucker-rod-type pumps and submersible centrifugal pumps, excentric screw pumps (so-called progressing cavity pumps) belong to standard conveyors in the production of crude oil. The authors of the contribution under consideration present the further development of excentric screw pumps with respect to the reduction of fluid levels in gas wells. This further development is based on a co-operation between the operator (Rohoel Aufsuchungs AG (Gampern, Austria)), the pump supplier (NETZSCH Oilfield Products GmbH (Selb, Federal Republic of Germany)) and the Institute for Process Technologies and Machinery at the University of Erlangen-Nuernberg (Federal Republic of Germany). The authors report on first attempts with the excentric screw pump at Weizberg (Federal Republic of Germany), material investigations at the University of Erlangen-Nuernberg, optimization of pump components and pump systems as well as on the optimization of the entire drainage process. ...

British Library Electronic Table of Contents (United Kingdom)

Abstract We have experimentally and theoretically investigated the equivalent magnetic noise in a magnetoelectric Metglas/ 0.7Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 laminate sensor unit by considering the constituent noise sources of dielectric loss (NDE) and DC leakage resistance (NR). In the low frequency range (f = 1 Hz), theory predicts that NR dominates the noise charge (1.6 times larger than NDE), with a 1 Hz noise of 9.1\\;{\\rm pt}/\\sqrt {\\rm Hz}. The experimental equivalent magnetic noise was 10.8\\;{\\rm pt}/\\sqrt {\\rm Hz}. This observed value is slightly higher than the predicted one, which might be due to an oversimplification of the theoretical model in terms of electrical charge amplifier and external vibration noise sources. ( 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

Energy Technology Data Exchange (ETDEWEB)

Lining shafts and placing them in a given strata needs extensive computation. Therefore, it is natural that the use of electronic computing and of numerical methods in this mining area started early. For shafts being sunk in non-stable water-bearing strata the deformations and stresses of the freezing wall are analysed. The complex system of an outer lining in the shaft sinking stage is designed with regard to the elastic support of the strata. In cases of strata-embedded systems the tubbing liner can be shaped as the loads require. Here analysis of safety against buckling is very important. If a sliding shaft is built as a composite construction, there are advantages in determining the distribution of the material by numerical methods. The analysis of stability is possible only by numerical methods and could not be solved otherwise. The Finite Element Method proves itself as a very general tool to solve the problem of multi-axial states of stress in a foundation section. The use of ...

Energy Technology Data Exchange (ETDEWEB)

Shell Solar GmbH is working on a variant of the so-called stacked elemental layer process for CIGSSe absorber production. The metal films resp. the selenium are deposited on the Mb electrode at room temperature by DC sputtering (CIG) or evaporation (Se) and then processed into semiconductors by rapid thermal annealing (RTP). Currently, the mean efficiency of the pilot plant is i 12.6 {+-} 0.2 % for non-sealed 30 x 30 cm{sup 2} modules, the key efficiency is 13.0 %. In addition to the 30 x 30 cm{sup 2} pilot line, a small series of 60x90cm2 modules was constructed in December 2004. Here, the mean efficiency was 13.0 percent while the average module power was higher than 60 W. The contribution also describes investigations of ceramically sputtered n-ZnO:Al layers with reduced Al concedntrations of 1 percent and on reactively sputtered n-ZnO.Al layers from the double roller magnetron. (orig.) [German] Bei Shell Solar GmbH wird eine Variante des ...

Energy Technology Data Exchange (ETDEWEB)

To permit an assessment of the system presented in this paper the data collected up to this point should be complemented by further experience with its practical use in electromobiles and the recovery of zink and the electrolyte. To this end the system is to be tested in electromobiles in 1995 and 1996. If there are no serious problems in the course of these tests and the above-mentioned estimates on economic efficiency are confirmed, then there is much to be said for a large-scale trial of these battery systems in electromobiles in the framework of a pilot project in Karlsruhe. Because of the infrastructure required for recharging, such a project should first be carried out in cooperation with fleet operators. As the recharging technique employed is so simple as to require no great investment and cost-effectiveness should already be achievable with a few tens of vehicles, one can conceive of a whole variety of applications in cooperation with public utilities, municipalities, and ...

Energy Technology Data Exchange (ETDEWEB)

Many industrial workshops in Germany were erected during the 40s and 50s, especially at the beginning of the economic boom. After more than 40 years, these facilities are in need of structural and production-technical modernization. A case in point is the carriage fabrication workshop of the Salzgitter-based company Linke-Hoffmann-Busch. The characteristic features of this type of building are large glazed areas, free uncontrolled ventilation and substantial height. Opportunities for energy-oriented and light-technical modernization are demonstrated at this Salzgitter workshop in exemplary form, the emphasis being on the use of solar energy components and, particularly, transparent thermal insulation. (orig.) [Deutsch] In der Bundesrepublik Deutschland gibt es viele Produktionshallen, die in den vierziger und fuenfziger Jahren, insbesondere zu Beginn des wirtschaftlichen Aufschwungs, errichtet wurden. Diese Hallen sind nach ueber vierzig Jahren sowohl aus baulichen als auch ...

Energy Technology Data Exchange (ETDEWEB)

Gas quenching for the hardening of steel parts is a lower-pollution alternative to quenching in quenchants such as oil or salt. As the surfaces of the cooled parts remain clean after gas quenching, there is no need to wash them after heat treatment, which reduces the consumption of oils and detergents. The fire risk and ventilation requirements of oil quenching are eliminated. In addition, some trials have shown that gas quenching has a positive effect on distortion, representing a saving in finishing work and thus a reduction in costs. Today, gas quenching is used almost solely in vacuum furnaces. Quenching is normally performed in the same chamber as heating, which means that besides quenching the batch, the quenching system must also remove heat from the heating elements and insulation of the furnace. Previous trials performed by IVF have shown that gas quenching with helium of ball bearing and carburizing steels (and other steels) in sizes up to 25 mm at pressures up to 20 bar in a ...

International Nuclear Information System (INIS)

Ultra low loading noble metal (0.04-0.12 mg_P_t/cm"2) based electrodes were obtained by direct metallization of non-catalyzed gas diffusion layers via dual ion beam assisted deposition (IBAD) method. Fuel cell performance results reported earlier indicate significant improvements in terms of mass specific power density of 0.297 g_P_t/kW with 250 A thick IBAD deposit (0.04 mg_P_t/cm"2 for a total MEA loading of 0.08 mg_P_t/cm"2) at 0.65 V in contrast to the state of the art power density of 1.18 g_P_t/kW using 1 mg_P_t_(_M_E_A_)/cm"2 at 0.65 V. In this article we report the peroxide radical initiated attack of the membrane electrode assembly utilizing IBAD electrodes in comparison to commercially available E-TEK (now BASF Fuel Cell GmbH) electrodes and find the pathway of membrane degradation as well. A novel segmented fuel cell is used for this purpose to relate membrane degradation to peroxide generation at the electrode/electrolyte interface by means of ...

Energy Technology Data Exchange (ETDEWEB)

Si nanocrystal floating gate MOS capacitors were formed on p-Si (100) wafers by thermal plasma jet (TPJ) annealing of SiO{sub 2}/SiO{sub x} /SiO{sub 2}/Si(100) stacked structure. The chemical composition of SiO{sub x} layer was controlled by changing the SiH{sub 4}, He, and O{sub 2} gas flow ratio during plasma enhanced chemical vapour deposition. The MOS capacitors showed clear hysteresis in capacitance-voltage (CV) characteristics after TPJ annealing. The hysteresis width shows maximum value when initial composition x =1.7, which shows the maximum photoluminescence (PL) intensity. The maximum hysteresis width of 6.8 V was observed with gate voltage swept between 20 and -20 V in x = 1.7 sample. The result means 7.4 x 10{sup 12} cm{sup -2} carriers are injected to or emitted from Si nanocrystals. The duration of 1 V shift in flatband voltage was {proportional_to}0.1 ms with 20 V pulse, and charged carriers were stably maintained for {proportional_to}2 hours. (copyright 2010 WILEY-VCH ...

International Nuclear Information System (INIS)

Mn-modified Pb0.92La0.08(Zr0.65Ti0.35)O3 (PLZT) was prepared chemically by a coprecipitate method using their respective nitrate salts and isopropoxides. Differential thermal analysis (DTA) and X-ray analysis clearly show the formation of PLZT single rhombohedral phase for samples calcined beyond 750 C. Uniform grain distribution was observed from scanning electron microscopic (SEM) studies and grain size was found to increase with Mn doping up to x=0.08 and then decreased. Dielectric measurement shows the decrease in peak transition temperature (TC) with Mn doping up to x=0.12 and then increase along with a sharp rise in dielectric maxima. A diffuse dielectric dispersion is observed in all the compositions. A detailed dispersion study was carried out using the Vogel-Fulcher empirical relation, a universal relaxation law and the Havriliak-Negami function. The Vogel-Fulcher relation fitting parameters of activation energy and freezing temperature were found to decrease with Mn doping up ...

Energy Technology Data Exchange (ETDEWEB)

Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X = 1 {mu}m and an intermediate inter-pillar gap size of Y = 4 {mu}m with superhydrophobic CAs over 170 . Surface analysis with X-ray photoelectron spectroscopy (XPS) revealed that CF{sub 3} groups were present at the ...

Science.gov (United States)

In the past few decades the need for improved nuclear reactor safety analyses has led to a rapid development of advanced methods for multidimensional thermal-hydraulic analyses. These methods have become progressively more complex in order to account for the many physical phenomena anticipated during steady state and transient Light Water Reactor (LWR) conditions. The advanced thermal-hydraulic subchannel code COBRA-TF (Thurgood, M. J. et al., 1983) is used worldwide for best-estimate evaluations of the nuclear reactor safety margins. In the framework of a joint research project between the Pennsylvania State University (PSU) and AREVA NP GmbH, the theoretical models and numerics of COBRA-TF have been improved. Under the name F-COBRA-TF, the code has been subjected to an extensive verification and validation program and has been applied to variety of LWR steady state and transient simulations. To enable F-COBRA-TF for industrial applications, including safety ...

International Nuclear Information System (INIS)

Full text: Introduction. Children, especially premature infants and neonates, are at a much higher risk to obtain an X ray induced disturbance of life - particularly cancer. On the one hand this is due to their longer life expectancy and on the other hand it is due to their higher cell proliferation rate. The paediatric radiology unit of the Inselspital Bern recently installed some of the most advanced X ray equipment nowadays available. It is based on the two latest digital technologies: double read computed radiography (CR) and direct digital radiography (DR). Only the implementation of these digital radiography systems permits the digital acquisition and additionally the analysis of acquired data. The systematic analysis of large amounts of biometric data and exposition data is the basis for further dose reduction and a systematic quality control (QC). Patients are increasingly critical concerning radiation exposure - especially parents regarding their children. Besides an ...