International Nuclear Information System (INIS)

Techniques for reducing computation time in 3D photon dose calculations are addressed with specific emphasis given to the convolution/superposition approach. A single polyenergetic superposition model calculating absorbed dose per incident photon fluence (Gy cm"2) was developed in terms of TERMA and a total energy deposition kernel (a total point spread function). A novel approach was devised for reducing calculation time. The method, named the CF method, was based on the use of a conventional, fast model (here a modified power-law method was used) for the generation of 3D dose distributions on a fine dose matrix. Superposition calculations were carried out on a coarse matrix and calculation speed was increased simply by reducing the number of calculations. A set of correction factors was derived on the coarse grid from the ratio of the dose values from ...

Energy Technology Data Exchange (ETDEWEB)

Experiments were conducted to confirm the isotropic spatial resolution of multislice CT with a 0.5 mm slice thickness. Isotropic spatial resolution means that the spatial resolution in the transaxial plane (X-Y plane) and that in the longitudinal direction (Z direction) are equivalent. To obtain point spread function (PSF) values in the X-Y-Z directions, three-dimensional voxel data were obtained by helical scanning of a bead phantom. The modulation transfer function (MTF) values were then obtained by three-dimensional Fourier transform of the PSF. Evaluation of the spatial resolution in the X-Y-Z directions by the MTF values showed that the spatial resolution in the Z direction does not depend on the reconstruction kernel used. It was also found that the spatial resolution in the Z direction, as compared with that in the X-Y plane, is superior with the standard kernel for the abdomen and is inferior with the high-definition ...

International Nuclear Information System (INIS)

Dose calculations for radiation arc therapy are traditionally performed by approximating continuous delivery arcs with multiple static beams. For 3D conformal arc treatments, the shape and weight variation per degree is usually small enough to allow arcs to be approximated by static beams separated by 5"0-10"0. But with intensity-modulated arc therapy (IMAT), the variation in shape and dose per degree can be large enough to require a finer angular spacing. With the increase in the number of beams, a deterministic dose calculation method, such as collapsed-cone convolution/superposition, will require proportionally longer computational times, which may not be practical clinically. We propose to use a homegrown Monte Carlo kernel-superposition technique (MCKS) to compute doses for rotational delivery. The IMAT plans were generated with 36 static beams, which were subsequently interpolated into finer angular intervals for dose calculation to mimic ...

International Nuclear Information System (INIS)

Accurate dose calculation in radiation treatment planning is most important for successful treatment. Since human body is composed of various materials and not an ideal shape, it is not easy to calculate the accurate effective dose in the patients. Many methods have been proposed to solve inhomogeneity and surface contour problems. Monte Carlo simulations are regarded as the most accurate method, but it is not appropriate for routine planning because it takes so much time. Pencil beam kernel based convolution/superposition methods were also proposed to correct those effects. Nowadays, many commercial treatment planning systems have adopted this algorithm as a dose calculation engine. The purpose of this study is to verify the accuracy of the dose calculated from pencil beam kernel based treatment planning system comparing to Monte Carlo simulations and measurements especially in ...

CERN Document Server

Let $\\mathscr{P}(E)$ be the space of probability measures on a measurable space $(E,\\mathcal{E})$. In this paper we introduce a class of nonlinear Markov chain Monte Carlo (MCMC) methods for simulating from a probability measure $\\pi\\in\\mathscr{P}(E)$. Nonlinear Markov kernels (see [Feynman--Kac Formulae: Genealogical and Interacting Particle Systems with Applications (2004) Springer]) $K:\\mathscr{P}(E)\\times E\\rightarrow\\mathscr{P}(E)$ can be constructed to, in some sense, improve over MCMC methods. However, such nonlinear kernels cannot be simulated exactly, so approximations of the nonlinear kernels are constructed using auxiliary or potentially self-interacting chains. Several nonlinear kernels are presented and it is demonstrated that, under some conditions, the associated approximations exhibit a strong law of large numbers; our proof technique is ...

Energy Technology Data Exchange (ETDEWEB)

Validation of nuclear power reactor signals is often performed by comparing signal prototypes with the actual reactor signals. The signal prototypes are often computed based on empirical data. The implementation of an estimation algorithm which can make predictions on limited data is an important issue. A new machine learning algorithm called support vector machines (SVMS) recently developed by Vladimir Vapnik and his coworkers enables a high level of generalization with finite high-dimensional data. The improved generalization in comparison with standard methods like neural networks is due mainly to the following characteristics of the method. The input data space is transformed into a high-dimensional feature space using a kernel function, and the learning problem is formulated as a convex quadratic programming problem with a unique solution. In this paper the authors have applied the SVM method for ...

CERN Document Server

Standard methods in non-linear analysis are used to show that there exists a parabolic branching of solutions of the Lichnerowicz-York equation with an unscaled source. We also apply these methods to the extended conformal thin sandwich formulation and show that if the linearised system develops a kernel solution for sufficiently large initial data then we obtain parabolic solution curves for the conformal factor, lapse and shift identical to those found numerically by Pfeiffer and York. The implications of these results for constrained evolutions are discussed.

International Nuclear Information System (INIS)

The convolution/superposition calculations for radiotherapy dose distributions are traditionally performed by convolving polyenergetic energy deposition kernels with TERMA (total energy released per unit mass) precomputed in each voxel of the irradiated phantom. We propose an alternative method in which the TERMA calculation is replaced by random sampling of photon energy, direction and interaction point. Then, a direction is randomly sampled from the angular distribution of the monoenergetic kernel corresponding to the photon energy. The kernel ray is propagated across the phantom, and energy is deposited in each voxel traversed. An important advantage of the explicit sampling of energy is that spectral changes with depth are automatically accounted for. No spectral or kernel hardening corrections are needed. Furthermore, the continuous sampling of photon direction allows us to ...

International Nuclear Information System (INIS)

A method has been developed for calibration of CT-numbers to volumetric electron density distributions using tissue substitutes of known elemental composition and experimentally determined electron density. This information have been used in a dose calculation method based on photon and electron interaction processes. The method utilizes a convolution integral between the photon fluence matrix and dose distribution kernels. Inhomogeneous media are accounted for using the theorems of Fano and O'Connor for scaling dose distribution kernels in proportion to electron density. For clinical application of a calculated dose plan, a method for prediction of accelerator output have been developed. The methods gives the number of monitor units that has to be given to obtain a certain absorbed dose to a point inside an irregular, inhomogeneous object. ...

UK PubMed Central (United Kingdom)

Sectors of Zea mays cobs, with and without kernels were cultured in vitro in the presence and absence of fluridone. Cultured kernels, cob tissue, and embryos developed...Full Text Available

UK PubMed Central (United Kingdom)

The relative role of the maternal source and the filial sink in controlling the composition of maize (Zea mays L.) kernels is unclear and may be influenced by the genotype and the N...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study was to test a large sample of different coronary artery stents using four image reconstruction approaches with respect to lumen visualization, lumen attenuation, and image noise in 64-slice multidetector-row computed tomography (MDCT) in vitro and to provide a catalogue of currently used coronary artery stents when imaged with state-of the-art MDCT. We examined 68 different coronary artery stents (57 stainless steel, four cobalt-chromium, one cobalt-alloy, two nitinol, four tantalum) in a coronary artery phantom (vessel diameter 3 mm, intravascular attenuation 250 HU, extravascular density -70). Stents were imaged in axial orientation with standard parameters: 32x0.6 collimation, pitch 0.24, 680 mAs, 120 kV, rotation time 0.37 s. Four different image reconstructions were obtained with varying convolution kernels and section thicknesses: (1) soft, 0.6 mm, (2) soft, 0.75, (3) medium soft, 0.6, and (4) stent-optimized ...

UK PubMed Central (United Kingdom)

Sugar release from the pedicel tissue of maize (Zea mays L.) kernels was studied by removing the distal portion of the kernel and the lower endosperm, followed by replacement of the...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

In this article, self-organizing-map-based video object segmentation is proposed, assuming that either Y-quantification or HSV-quantification can be systematically selected. Given a video sequence, the value of the probability density function for each component value is calculated according to a kernel estimation at the first frame. Some areas randomly chosen from the background are then examined, using each component value, to judge whether or not they include the target object. The quantification is determined so that the frequency of occurrence of false extractions can be reduced. The data presented to the maps are generated based on the selected quantification. Experimental results show that the proposed method recognizes the target object well.

International Nuclear Information System (INIS)

We report on the improvement of Critical Dimension (CD) linearity on a photomask by applying the concept of process proximity correction to a laser lithographic process used for fabrication of photomasks. Rule-based Laser Process proximity Correction (LPC) was performed using an automated optical proximity correction tool and we obtained dramatic improvement of CD linearity on a photomask. A study on model-based LPC was executed using a two-Gaussian kernel function and we extracted model parameters for the laser lithographic process by fitting the model-predicted CD linearity data with measured ones. Model-predicted bias values of isolated space (I/S), Arrayed Contact (A/C) and Isolated Contact (I/C) were in good agreement with those obtained by the nonlinear curve-fitting method used for the rule-based LPC.

CERN Document Server

Recently, applying the novel data mining techniques for evaluating enterprise financial distress has received much research alternation. Support Vector Machine (SVM) and back propagation neural (BPN) network has been applied successfully in many areas with excellent generalization results, such as rule extraction, classification and evaluation. In this paper, a model based on SVM with Gaussian RBF kernel is proposed here for enterprise financial distress evaluation. BPN network is considered one of the simplest and are most general methods used for supervised training of multilayered neural network. The comparative results show that through the difference between the performance measures is marginal; SVM gives higher precision and lower error rates.

International Nuclear Information System (INIS)

In radiotherapy treatment planning, convolution/superposition algorithms currently represent the best practical approach for accurate photon dose calculation in heterogeneous tissues. In this work, the implementation, accuracy and performance of the FFT convolution (FFTC) and multigrid superposition (MGS) algorithms are presented. The FFTC and MGS models use the same 'TERMA' calculation and are commissioned using the same parameters. Both models use the same spectra, incorporate the same off-axis softening and base incident lateral fluence on the same measurements. In addition, corrections are explicitly applied to the polyenergetic and parallel kernel approximations, and electron contamination is modelled. Spectra generated by Monte Carlo (MC) modelling of treatment heads are used. Calculations using the MC spectra were in excellent agreement with measurements for many linear accelerator types. To speed up the calculations, a number of ...

International Nuclear Information System (INIS)

A number of procedures in diagnostic radiology and cardiology make use of long exposures to x-rays from fluoroscopy units. Although numerous studies have been performed to measure or calculate skin dose from these procedures, there have only been a handful of studies to determine the dose to the other organs. This thesis was focused on devising a method to calculate the absorbed dose to underlying tissues and organs. The work was performed in several stages. First, a commercial convolution/superposition-based treatment planning system used in radiation oncology was modified and complemented to make it usable with the low energies of x-rays used in diagnostic radiology. This required generation of energy deposition kernels in the kilovoltage energy range. The kernels were generated using the EGS4 Monte Carlo system of codes and added to the treatment planning system. The treatment planning system was then evaluated for its ...

International Nuclear Information System (INIS)

Using Monte Carlo simulation and the convolution/superposition algorithm, this work examines percent depth dose curves of the central axis in an acrylic phantom (20x20x20 cm"3) with variously sized air cavities (20x20x1.0, 20x20x2.0, 20x20x3.0, 20x20x4.0 and 20x20x4.95 cm"3 for study of longitudinal electron disequilibrium (ED) and 3.6x3.6x4.95, 4.5x4.5x4.95, 5.4x5.4x4.95 and 20x20x4.95 cm"3 for study of lateral ED). Radiochromic film samples are also measured to verify the Monte Carlo results. The Monte Carlo simulation is performed using OMEGA/BEAM and DOSXYZ codes, and the convolution/superposition calculation relies on an ADAC commercial treatment planning system. Underestimating the dose kernel expansion leads to overestimating the dose of what was found in the air cavity of ED using the convolution/superposition algorithm. Consequently, the dose in the rebuild-up region is influenced. The influenced region is on the acrylic phantom surface to a depth of about ...

Energy Technology Data Exchange (ETDEWEB)

The interpretation of soil amelioration experiments with peanuts is made difficult by the unpredictibility of the crop and by the many factors altered when ameliorating acid soils. The present study was conducted to investigate the effects of lime and gypsum applications on peanut kernel yield via the three first order yield components, pods per ha, kernels per pod, and kernel mass. On an acid medium sandy loam soil (typic Plinthustult), liming resulted in a highly significant kernel yield increase of 117% whereas gypsum applications were of no significant benefit. As indicated by path coefficient analysis, an increase in the number of pods per ha was markedly more important in increasing yield than an increase in either the number of kernels per pod or kernel mass. Furthermore, exch. Al was found to be particularly detrimental to pod number. It was postulated ...

International Nuclear Information System (INIS)

In connection with some applications of asymptotic numbers and asymptotic functions, proposed by Khr.Khristov, the problem of describing subsets of asymptotic numbers closed with respect to algebraic operations arises. The algebraic operations with asymptotic numbers are defined by classes of their representatives. All trivial or noncharacteristic solutions are avoided. A procedure for constructing sets of elements closed under action of an algebraic operation or a combination of two or more of them is given. It turns out that the closed sets are given by their kernels, the last being the minimal subsets which generate the whole set by the introduced algebraic operations. It is proved that such kernels exist always. . The closed sets are described by their correspondence with the kernels. (S.P.).

Energy Technology Data Exchange (ETDEWEB)

The optimization of ethylene furnace operations using cfd-based simulations has been addressed. The optimization problems have been cast into various formulations: the Multidisciplinary feasible (MDF) approach, the All-At-Once (AAO) approach and the Individual discipline feasible (IDF) approach. These approaches mainly differ in their handling of the state equations as constraints, and hence some of the formulations place restrictions on the methods used to solve the state equations.

UK PubMed Central (United Kingdom)

Kernels of Zea mays on an intact plant accumulate indole-3-acetic acid (IAA) at the rate of 190 ng g-1 fresh weight h-1. Of the IAA synthesized, 97% is in the esterified form and less than 3% remains...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This DOE handbook describes a systematic method for establishing and maintaining training programs that meet the requirements and expectations of DOE Orders 5480.18B and 5480.20. The systematic approach to training includes 5 phases: Analysis, design, development, implementation, and evaluation.

Science.gov (United States)

Numerical results on aeroelastic standard configurations are presented. The methods used for two dimensional configurations include the small perturbations approach for inviscid flow, coupling methods for unseparated flow, coupling methods for unseparated or separated, laminar or turbulent boundary layers, and a numerical solution of the Euler equations for inviscid flow. The three dimensional configurations are studied by the transonic small disturbance approach. The detailed results are given.

British Library Electronic Table of Contents (United Kingdom)

A new method of the synthesis of high molecular polybutylene terephthalate (PBT) is developed with the use of Irganox 1010, tris(nonylphenyl) phosphite and hypophosphite as stabilizers and boron nitride or boron oxide as a catalyst is proposed.

Energy Technology Data Exchange (ETDEWEB)

The authors solve the instability of perturbative vacuum of Gross-Neveu model. They use a variational method. The analysis is nonperturbative as it uses only equal time commmutator/anticommutator algebra.

British Library Electronic Table of Contents (United Kingdom)

Surveys were carried out in 2006 and 2007 in Umbria (central Italy) to evaluate the presence of mycotoxigenic fungi and mycotoxins in maize grain sampled at harvest. Fusarium spp., were the most abundant species detected in maize kernels, followed by Aspergillus species of sections Flavi and Nigri and by Penicillium spp. Among Fusarium species, F. verticillioides was the most prevalent species, as detected by PCR directly on the kernels and on the fungi isolated from the kernels, followed by F. proliferatum and F. subglutinans. Fumonisins were the predominant mycotoxins with values, on average, of 4.3 and 5.7mgkg-1, in 2006 and 2007, respectively, with a maximum of 76.3mgkg-1 in the second year. Deoxynivalenol ranged from 0.2 to 3.98mgkg-1 in 2006 (average 1.04mgkg-1) and from undetectable...

International Nuclear Information System (INIS)

Purpose: An inverse treatment planning algorithm for tomotherapy is described. Methods and Materials: The algorithm iteratively computes a set of nonnegative beam intensity profiles that minimizes the least-squares residual dose defined in the target and selected normal tissue regions of interest. At each iteration the residual dose distribution is transformed into a set of residual beam profiles using an inversion method derived from filtered backprojection image reconstruction theory. These 'residual' profiles are used to correct the current beam profile estimates resulting in new profile estimates. Adaptive filtering is incorporated into the inversion model so that the gross structure of the dose distribution is optimized during initial iterations of the algorithm, and the fine structure corresponding to edges is obtained at later iterations. A three dimensional, kernel based, convolution/superposition dose model is used ...

UK PubMed Central (United Kingdom)

Motivation: Cell tracking is an important method to quantitatively analyze time-lapse microscopy data. While numerous methods and tools exist for tracking cells in 2D time-lapse images,...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

In modern quality engineering, dual response surface methodology is a powerful tool to model an industrial process by using both the mean and the standard deviation of the measurements as the responses. The least squares method in regression is often used to estimate the coefficients in the mean and standard deviation models, and various decision criteria are proposed by researchers to find the optimal conditions. Based on the inherent hierarchical structure of the dual response problems, we propose a Bayesian hierarchical approach to model dual response surfaces. Such an approach is compared with two frequentist least squares methods by using two real data sets and simulated data.

UK PubMed Central (United Kingdom)

A monoclonal antibody raised against carboxyl-linked IAA was used in Western blot analysis of storage proteins from kernels of Avena sativa, Pennisetum americanum, Sorghum bicolor,...Full Text Available

UK PubMed Central (United Kingdom)

In germinating oil palm (Elaeis guineensis var D × P) seedling, an active lipase was present in the shoot but absent from both the kernel and the haustorium. It has an optimum...Full Text Available

UK PubMed Central (United Kingdom)

Indole-3-acetyl-myo-inositol occurs in both the kernel and vegetative shoot of germinating Zea mays seedlings. The effect of a gravitational stimulus on the transport...Full Text Available

CERN Document Server

We construct representation of the Separated Variables (SoV) for the quantum SL(2,R) Heisenberg closed spin chain and obtain the integral representation for the eigenfunctions of the model. We calculate explicitly the Sklyanin measure defining the scalar product in the SoV representation and demonstrate that the language of Feynman diagrams is extremely useful in establishing various properties of the model. The kernel of the unitary transformation to the SoV representation is described by the same "pyramid diagram" as appeared before in the SoV representation for the SL(2,C) spin magnet. We argue that this kernel is given by the product of the Baxter Q-operators projected onto a special reference state.

British Library Electronic Table of Contents (United Kingdom)

SummaryThis paper examines the sensitivity and uncertainty of evaporation estimates from Nasser Lake, south of Egypt using data collected at the floating station Raft, 2km upstream of the Aswan High Dam, and 12 evaporation models. Based on their approach the evaporation models were ranked in five classes, respectively the Bowen ratio energy budget (BREB) approach, three energy-aerodynamic based methods, a mass transfer method, two temperature and five solar radiation-temperature approaches. State dependent parameter models were used to estimate the sensitivity indices of the different evaporation estimation methods at daily and monthly frequencies. A drastic reduction in the cost of the sensitivity analysis was obtained when coupled with efficient sampling methods, producing quasi-Monte Ca...

Energy Technology Data Exchange (ETDEWEB)

The Porous media approach method was applied to the MULTID component of MARS which was developed by KAERI. This method has been widely used for analysis of large regions containing only fluid and for flows in regions with immersed solids. It can calculate flow distribution more correctly in case of flow area or volume change. Application of this method to the MULTID component in MARS was evaluated and the results were compared with those of CFD code, FLUENT. As a result, the calculated flow distributions of MARS and FLUENT show similar trend, so the effect of porous media in MARS can be applied to the other cases.

Energy Technology Data Exchange (ETDEWEB)

This research has two main goals. First, we wanted to introduce optimization tools in the diffusion code DONJON, mostly for fuel management. The second objective is more practical. The optimization capabilities are applied to the fuel management problem for different CANDU reactors at refueling equilibrium state. Two kinds of approaches are considered and implemented in this study to solve optimization problems in the code DONJON. The first methods are based on gradients and on the quasi-linear mathematical programming. The method initially developed in the code OPTEX is implemented as a reference approach for the gradient based methods. However, this approach has a major drawback. Indeed, the starting point has to be a feasible point. Then, several approaches have been developed to be more general and not limited by the initial point ...

Energy Technology Data Exchange (ETDEWEB)

This manual describes the use of the Xyce Parallel Electronic Simulator. Xyce has been designed as a SPICE-compatible, high-performance analog circuit simulator, and has been written to support the simulation needs of the Sandia National Laboratories electrical designers. This development has focused on improving capability over the current state-of-the-art in the following areas: (1) Capability to solve extremely large circuit problems by supporting large-scale parallel computing platforms (up to thousands of processors). Note that this includes support for most popular parallel and serial computers; (2) Improved performance for all numerical kernels (e.g., time integrator, nonlinear and linear solvers) through state-of-the-art algorithms and novel techniques. (3) Device models which are specifically tailored to meet Sandia's needs, including some radiation-aware devices (for Sandia users only); and (4) Object-oriented code design and implementation using ...

Science.gov (United States)

We attempt to image the rupture propagation of the 2004 M6.0 Parkfield earthquake by analyzing records from the USGS Parkfield seismic array (UPSAR) and other strong-motion stations. The UPSAR array consists of 12 stations distributed over about one square kilometer at a distance of 10~km from the San Andreas fault near Parkfield, California. We employ a method that uses reverse time migration to stack the seismograms at back-projected locations along the fault. We use waveform cross-correlation to align the initial P-wave arrivals and correct for small static time shifts in the records. This forces a coherent image at the hypocenter at the quake origin time. Initial results at later time steps show some evidence of the expected rupture propagation to the north. However, the resolution of the back-projection is limited by the small aperture of the UPSAR array. Records from other strong-motion stations can improve the theoretical resolution ...

Energy Technology Data Exchange (ETDEWEB)

The methodology of achieving a high power density (HPD, or brake mean effective pressure) direct-injection Diesel engine has been studied, which is directed to using high fuel/air ratio, high-speed and ceramic engine components. Among the main thrust to achieve these engine changes for an advanced Diesel engine is the design of a high injection pressure (HIP) fuel system. During the course of the present study, two Cummins 903 engines mated with a Rutger-built HIP were employed to investigate the engine response to HIP and in-cylinder processes by using the Rutgers high-speed infrared (IR) spectral digital imaging system. Five separate technical publications were prepared to report results obtained from the study. The main findings include: The HIP system permits engine operation at an air/fuel ratio of as rich as 18 to 1 with smoke emission not worse than with the conventional mechanical (low pressure) injection system; A high injection pressure improves HPD of a Diesel engine; A HIP ...

International Nuclear Information System (INIS)

Purpose/Objective: With the advent of computed tomography and magnetic resonance imaging, the three dimensional representation of the patient anatomy has become an invaluable resource for better diagnosis and delineation of the target volume and sensitive structures in radiation therapy. Although the therapeutic linear accelerator industry has made available highly sophisticated equipment, the aggressiveness in dose prescription and delivery has to be complimented by accurate dose computation methods. We have adopted a convolution/superposition algorithm for the calculation of absolute dose that fully accounts for the external shape and internal structure of the patient for photon treatment radiotherapy. In this paper, we will discuss the principles of the convolution algorithm and we will show how the computed dose compares to clinically relevant treatment techniques. Materials and Methods: A computer controlled data acquisition system and a ...

Energy Technology Data Exchange (ETDEWEB)

The fuzzy polar power system stabilizer (FPPSS) which has been recently developed is analyzed using frequency domain methods. the frequency domain approach allows the PSS designer to compare the new FPPSS with more conventional controllers. The significance of the three FPPSS design parameters are readily seen from the frequency response data, and their relationship to the conventional lead-lag design approach can be evaluated. Furthermore, the frequency response data for the FPPSS allows an alternate design approach for this stabilizer, and can be used to develop information concerning the small signal stability of the resulting system.

Science.gov (United States)

A 56-year-old man admitted to our hospital for cardiac tamponade due to dilated cardiomyopathy did not respond to treatment by usual medical means or surgery. Pericardio-peritoneal drainage was conducted using a subcostal approach. Seven months later, the patient remains well and free of signs of pericardial tamponade. This method has proved to be safe and effective in patients with persistent massive pericardial effusion. PMID:10496067

CERN Document Server

Dictionary lookup methods are popular in dealing with ambiguous letters which were not recognized by Optical Character Readers. However, a robust dictionary lookup method can be complex as apriori probability calculation or a large dictionary size increases the overhead and the cost of searching. In this context, Levenshtein distance is a simple metric which can be an effective string approximation tool. After observing the effectiveness of this method, an improvement has been made to this method by grouping some similar looking alphabets and reducing the weighted difference among members of the same group. The results showed marked improvement over the traditional Levenshtein distance technique.

UK PubMed Central (United Kingdom)

BackgroundWe aimed to compare visual and refractive outcome following phacoemulsification and intraocular lens implant (IOL) and combined one-site phacotrabeculectomy.MethodWe...Full Text Available

UK PubMed Central (United Kingdom)

We introduce in this paper a new method for reducing neurodynamical data to an effective diffusion equation, either experimentally or using simulations of biophysically detailed models. The dimensionality...Full Text Available

CERN Document Server

We present a unified self-consistent review of the approach to spherical harmonics developed in the second half of the 19th century by Maxwell and by Thomson and Tait. We remark how this spherical coordinate-free approach straightforwardly leads to physically very important results of the theory of solid and surface harmonics which become rather tedious to work out when using spherical coordinates and associated Legendre functions. These results include, among others, the addition theorem, spherical wave expansions, the construction of the standard set of normalized spherical harmonics, Y_lm - together with their rotational properties-, and recursion relations. We provide new proofs for Maxwell's theorem, the addition theorem and Hobson's theorem, respectively, using in the latter some elementary notions of the symbolic techniques proper of the theory of invariants. Also, we give an approach based on compact vector ...

CERN Document Server

We consider a family of chiral non-Hermitian Gaussian random matrices in the unitarily invariant symmetry class. The eigenvalue distribution in this model is expressed in terms of Laguerre polynomials in the complex plane. These are orthogonal with respect to a non-Gaussian weight including a modified Bessel function of the second kind, and we give an elementary proof for this. In the large $n$ limit, the eigenvalue statistics at the spectral edge close to the real axis are described by the same family of kernels interpolating between Airy and Poisson that was recently found by one of the authors for the elliptic Ginibre ensemble. We conclude that this scaling limit is universal, appearing for two different non-Hermitian random matrix ensembles with unitary symmetry. As a second result we give an equivalent form for the interpolating Airy kernel in terms of a single real integral, similar to representations for the asymptotic ...

Energy Technology Data Exchange (ETDEWEB)

The theory and application of the optimal control of linear systems to stabilize or improve the system stability is well known. For an optimal linear regulator design, the arbitrariness involved in the parameters of the cost function always affects the final control law and the closed-loop system poles which decide the system dynamic characteristics. A new approach, 'The inverse problem approach' has been developed to overcome this difficulty. The system so designed will have preassigned closed-loop poles and the resulting closed-loop system performance can be ensured. In this paper the inverse problem approach for optimal regulator design is applied to the power system stabilizer (PSS) design for single-machine infinite-bus systems. The results show that, as far as the linearized model is concerned, systems designed by the inverse problem approach have better closed-loop performance ...

Science.gov (United States)

In this article, we propose a model selection method, the Bayesian composite model space approach, to map quantitative trait loci (QTL) in a half-sib population for continuous and binary traits. In our method, the identity-by-descent-based variance component model is used. To demonstrate the performance of this model, the method was applied to map QTL underlying production traits on BTA6 in a Chinese half-sib dairy cattle population. A total of four QTLs were detected, whereas only one QTL was identified using the traditional least square (LS) method. We also conducted two simulation experiments to validate the efficiency of our method. The results suggest that the proposed method based on a multiple-QTL model is efficient in mapping multiple QTL for an outbred half-sib population and is more powerful than the LS method ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a new method for the determination of the energy gap of superconductors. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. The maximum voltage in differential conductance V/sub max/ was measured from the electron tunneling spectrum. From V/sub max//kT and the curve, one can easily calculate the energy gap value ..delta... This method is simple, and the accuracy almost approaches that of the curve-fitting method.

Energy Technology Data Exchange (ETDEWEB)

A new method for determining the energy gap of a superconductor using the maximum in the differential conductance curve of electron tunneling spectrum is given in this paper. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. V/sub max/, the voltage of the conductance maximum, can be measured from electron tunneling spectrum. ..delta../kT can be found from this curve, then the energy gap ..delta.. can be calculated. This method is simple, fast and accurate. The accuracy almost approaches that of the curve fitting method.

Energy Technology Data Exchange (ETDEWEB)

Ultrasound tomography is an attractive imaging method for the detection of breast cancer. The complex anatomy of the breast with its different spatial scales and material property contrasts make accurate reconstructions very challenging. This paper proposes a hybrid approach whereby Travel-of-Flight and Diffraction Tomography are combined together to achieve high-resolution and high-accuracy sound-speed reconstructions. The method is validated with several numerical phantoms.

Energy Technology Data Exchange (ETDEWEB)

A variety of forecasting approaches have been used in the energy area. Forecast simulations provide a common basis for comparing the relative precision of different forecasting methods. This paper presents a forecast simulation made using smoothing procedures for forecasting time series. The simulation design, statistical analysis, and conclusions are provided.

Energy Technology Data Exchange (ETDEWEB)

Generalization of the alternate directions implicit technique is used to compute the pion propagator in quenched QCD on a lattice. The full four-dimensional problem is reduced to a series of partly decoupled two-dimensional inversions. Chiral properties of the theory computed in this approach agree with those found using other methods.

International Nuclear Information System (INIS)

This paper summarizes a method to evaluate the possible effects of magnetohydrodynamic-electromagnetic pulse (MHD-EMP) on power systems. This method is based on the approach adapted to study the impact of geomagnetic storms on power systems. The paper highlights the similarities and differences between the two phenomena. Also presented are areas of concern which are anticipated from MHD-EMP on the overall system operation. 12 refs., 1 fig.

British Library Electronic Table of Contents (United Kingdom)

Purpose - Burr distribution has been proved to be a useful failure model. It can assume different shapes which allow it to be a good fit for various lifetimes data. Hybrid censoring is an important way of generating lifetimes data. The purpose of this paper is to estimate an unknown parameter of the Burr type XII distribution when data are hybrid censored. Design/methodology/approach - The problem is dealt with through both the classical and Bayesian point of view. Specifically, the methods of estimation used to tackle the problem are maximum likelihood estimation method and Bayesian method. Empirical Bayesian approach is also considered. The performance of all estimates is compared through their mean square error values. The paper employs Monte Carlo simulation to evaluate the mean square...

Science.gov (United States)

In this paper, we propose a method based on the Laplacian in the frequency domain for video text detection. Unlike many other approaches which assume that text is horizontally-oriented, our method is able to handle text of arbitrary orientation. The input image is first filtered with Fourier-Laplacian. K-means clustering is then used to identify candidate text regions based on the maximum difference. The skeleton of each connected component helps to separate the different text strings from each other. Finally, text string straightness and edge density are used for false positive elimination. Experimental results show that the proposed method is able to handle graphics text and scene text of both horizontal and nonhorizontal orientation. PMID:20733217

UK PubMed Central (United Kingdom)

The first compound in the series of reactions leading to the ester conjugates of indole-3-acetic acid (IAA) in kernels of Zea mays sweet corn is the acyl alkyl acetal, 1-O-indol-3-ylacetyl-β-d-glucose...Full Text Available

Science.gov (United States)

Studies of the effectiveness of operant, relaxation, cognitive, and multimodal behavioural approaches to the treatment of chronic benign pain other than headache were evaluated. In general, the quality of the studies was poor, and most investigations lacked appropriate and adequate control conditions, outcome measures, and/or follow-ups. While outcome reports for all four behavioural treatments have been mainly positive, few data were found which conclusively demonstrate that any of the approaches are effective or that they are the treatment of choice. The data do, however, imply that behavioural approaches may help patients lead more normal and productive lives. Specifically, the literature suggests that: (1) the operant method leads to increased activity levels and decreased pain and drug intake, (2) the relaxation approach results in decreased EMG levels and some pain reductions, ...

British Library Electronic Table of Contents (United Kingdom)

Purpose - The article shares insights from a program that was developed to address burnout, compassion fatigue and vicarious trauma. The program works from the premise that people and organizations thrive when they have shared values and common understandings. Design/methodology/approach - The approach draws together reflection at the organizational and person levels. Connecting business ethics and organizational analysis, improving understanding of the body's energy as well as inter-cultural understanding are all achievable while adopting the resilience development methods. Findings - The article concludes that reflective practice through the tools used on the program enhances understanding of the challenges faced by organizations and the individuals involved. It provides creative routes ...

CERN Document Server

We provide a both qualitative and quantitative comparison among different approaches aimed to solve the problem of non-linear diffusive acceleration of particles at shocks. In particular, we show that state-of-the-art models (numerical, Monte Carlo and semi-analytical), even if based on different physical assumptions and implementations, for typical environmental parameters lead to very consistent results in terms of shock hydrodynamics, cosmic ray spectrum and also escaping flux spectrum and anisotropy. Strong points and limits of each approach are also discussed, as a function of the problem one wants to study.

Energy Technology Data Exchange (ETDEWEB)

A new approach for the selection of best PSS locations in multimachine power systems is proposed in this paper. Study shows that the right-eigenvector measures the activity of state variables and the left-eigenvector measures the control effect of control signals. Based on the right and left eigenvector the concept of sensitivity of PSS effect (SPE) is presented and used to identify the best PSS locations. The proposed method is used to identify the best PSS location in a 13-machine system to increase the damping of an interarea mode. The time-domain simulation results confirm that the prediction of best PSS location by SPE method is correct and accurate.

Science.gov (United States)

We have developed a novel laser ray-tracing method to measure aberrations in optical systems. It consists of delivering narrow laser pencils (by a laser scanner), recording the spots that are formed on the image plane (with a CCD camera), and computing the position of each centroid. This approach could be considered an experimental (approximate) implementation of standard numerical ray tracing. Several tests and experiments, including a direct comparison with a Hartmann-Shack wave-front sensor, provided highly satisfactory results that confirmed the validity of the method and revealed potential advantages. PMID:18073906

CERN Document Server

Mining association rules is a popular and well researched method for discovering interesting relations between variables in large databases. A practical problem is that at medium to low support values often a large number of frequent itemsets and an even larger number of association rules are found in a database. A widely used approach is to gradually increase minimum support and minimum confidence or to filter the found rules using increasingly strict constraints on additional measures of interestingness until the set of rules found is reduced to a manageable size. In this paper we describe a different approach which is based on the idea to first define a set of ``interesting'' itemsets (e.g., by a mixture of mining and expert knowledge) and then, in a second step to selectively generate rules for only these itemsets. The main advantage of this approach over increasing thresholds or filtering rules is ...

British Library Electronic Table of Contents (United Kingdom)

We propose an approach to achieving early recognition of gesture patterns. Early recognition is a method for recognizing sequential patterns at their earliest stage. Therefore, in the case of gesture recognition, we can get a recognition result for human gestures before the gestures are finished. The most difficult problem in early recognition is knowing when the system has determined the result. Most traditional approaches suffer from this problem, since gestures are often ambiguous. At the start of a gesture, in particular, it is very difficult to determinate the recognition result since insufficient input data have been observed. Therefore, we have improved on the traditional approach by using a self-organizing map.

British Library Electronic Table of Contents (United Kingdom)

Background For the past 14 years, we have been performing laparoscopic adrenalectomy via the lateral transabdominal as well as the posterior retroperitoneal approach. The aim of this study is to describe patient selection criteria for each approach with comparison of perioperative outcomes. Methods In patients with smaller tumors, low body mass index (BMI), history of previous abdominal operations, appropriate body habitus, and bilateral pathology, we have performed preferentially the posterior approach. Data regarding clinical pathology, tumor size, BMI, estimated blood loss (EBL), operating time (OT), morbidity, mortality, and duration of stay were analyzed retrospectively. Data are expressed as mean +- standard error of the mean (SEM). Results One hundred seventy-two laparoscopic adrena...

Science.gov (United States)

Motion Camouflage (MC) is illuminated as a novel strategy in counterattacking anti-satellite by way of stealth trajectory scheduling. The dynamics model of MC in space is developed and a quadratic function with three boundary constraints is employed for trajectory determination. Based on the model a scenario is set to run the simulation. The results indicate given the designed acceleration input, the predator will be moved following a prescribed route, which precisely locates the predator between two objects at each time instant. In the last approaching phase, the motion is achieved with a big bumping rate which guarantees the power of this striking. Methods for deriving minimum fuel cost in the fixed approaching duration and the minimum approaching duration in limited acceleration input are proposed and are verified in the simulation. At last, camouflage is recognized as a multi-faceted affair, in ...

British Library Electronic Table of Contents (United Kingdom)

Excellent mechanical properties and corrosion resistance combined with low weight qualify ?-titanium materials for lightweight applications in aviation, automotive and energy engineering. Thus far, actual applications of these materials have been limited due to high material costs and limited processing knowledge. One approach for developing resource-efficient manufacturing methods is the application of incremental forming methods. This article focuses on the development of the incremental spin extrusion process, which creates hollow profiles from solid bars. This method allows hollow shape manufacturing with a much higher flexibility than other forming methods and a significantly improved material utilization in comparison to machining methods, such as deep hole drilling. Beta-titanium al...

International Nuclear Information System (INIS)

In order to develop competitive and reliable nuclear power generation systems, development of innovative structural design methods is indispensable and risk-based design approach based on the assessment of failure probability is being developed. Fatigue is commonly considered as an important contributor to failure probability in many components of reactor systems and its assessment gives a large influence on total reliability of the plants. In order to assess its effect on the reliability, propagation of cracks needs to be evaluated as well as their initiation and pre-existence probability. As a part of new design approach, efforts are being taken to develop a simplified estimation method for fatigue crack growth under cyclic application of thermal and thermo-mechanical loading. A simplified estimation method of J-integral based on reference stress method and ...

British Library Electronic Table of Contents (United Kingdom)

Classical methods for the study of complex fluid phase behavior include static and dynamic equilibrium cells that usually require vapor and liquid recirculation. These are sophisticated, costly apparatus that require highly trained operators, usually months of labor-intensive work per mixture, and the data analysis is also rather complex. Simpler approaches to the fundamental study of azeotropes are highly desirable, even if they provide only selected cuts through the phase diagram. Recently, we introduced an advanced distillation curve measurement method featuring: (1) a composition explicit data channel for each distillate fraction (for both qualitative and quantitative analysis), (2) temperature measurements that are true thermodynamic state points that can be modeled with an equation o...

International Nuclear Information System (INIS)

The use of X-ray diffraction line profile analysis for the study of nanocrystalline powders is described. The fundamentals of the theory are presented in terms of crystallite/domain size, size distribution, lattice distortion, dislocations density and stacking faults. Line profile parameters and the methods of pattern fitting introduced to overcome the diffraction-line overlap problem are discussed. The approaches based of the integral breadth of the measured line profiles and the Fourier method are discussed. In addition, simplified approaches are also commented. Representative examples are selected to illustrate various cases of microstructure, such as nanomaterials with strain-free spherical nano crystallites, strain-free crystallites with anisotropic crystallite shape, anisotropic crystallites with microstrains and spherical crystallites with dislocation densities and crystallite size distributions. ...

British Library Electronic Table of Contents (United Kingdom)

We provide an efficient computational approach to solve the mixed integer programming (MIP) model developed by Tarim and Kingsman [8] for solving a stochastic lot-sizing problem with service level constraints under the static-dynamic uncertainty strategy. The effectiveness of the proposed method hinges on three novelties: (i) the proposed relaxation is computationally efficient and provides an optimal solution most of the time, (ii) if the relaxation produces an infeasible solution, then this solution yields a tight lower bound for the optimal cost, and (iii) it can be modified easily to obtain a feasible solution, which yields an upper bound. In case of infeasibility, the relaxation approach is implemented at each node of the search tree in a branch-and-bound procedure to efficiently sear...

Energy Technology Data Exchange (ETDEWEB)

This thesis consists of five chapters, each of which is a self-contained unit. The first chapter overviews methods for electronic-structure calculations. Chapter 2 introduces a new method to generate a rapidly converging configuration expansion. The approach iteratively combines (1) a least-squares fitting of a configuration expansion to a many-body wave function with (2) a transfer-matrix method for projecting out the ground state. Results are shown to be equivalent to multiconfiguration Hartree-Fock. Results from test calculations are given for a simple finite difference model of the helium atom. In Chapter 3 the use of the finite-element method in electronic structure calculations is discussed. Chapters 4 and 5 discuss developments in Monte Carlo methods based on Hubbard-Stratonovich transformations. Chapter 4 introduces a canonical ensemble formulation of ...

Energy Technology Data Exchange (ETDEWEB)

Removing noise from data is often the first step in data analysis. Denoising techniques should not only reduce the noise, but do so without blurring or changing the location of the edges. Many approaches have been proposed to accomplish this; in this paper, they focus on one such approach, namely the use of non-linear diffusion operators. This approach has been studied extensively from a theoretical viewpoint ever since the 1987 work of Perona and Malik showed that non-linear filters outperformed the more traditional linear Canny edge detector. They complement this theoretical work by investigating the performance of several isotropic diffusion operators on test images from scientific domains. They explore the effects of various parameters such as the choice of diffusivity function, explicit and implicit methods for the discretization of the PDE, and approaches for the spatial ...

CERN Document Server

We demonstrate the use of a variational method to determine a quantitative lower bound on the rate of convergence of Markov Chain Monte Carlo (MCMC) algorithms as a function of the target density and proposal density. The bound relies on approximating the second largest eigenvalue in the spectrum of the MCMC operator using a variational principle and the approach is applicable to problems with continuous state spaces. We apply the method to one dimensional examples with Gaussian and quartic target densities, and we contrast the performance of the basic Metropolis-Hastings algorithms with a ``smart'' variant that incorporates gradient information into the trial moves. We find that the variational method agrees quite closely with numerical simulations. We also see that the smart MCMC algorithm often fails to converge geometrically in the tails of the target density except in the simplest case we examine, ...

International Nuclear Information System (INIS)

The determination of the oxidation state of ultra-trace elements in the environment, especially in the case of actinides, is of importance in many ways. Speciation techniques using radiation may comprise methods based on the detection of the nuclear and atomic radiations emitted in radioactive decay or methods using external sources of excitation. In the former instance, information can be obtained from the energy and intensity of radiation, but at present the partition method is still the most commonly used, although its reliability is questionable. Excitation with intense laser beams, as is currently being used for trace element analysis in photoacoustic and thermal lensing spectroscopic techniques, could conceivably be applied under suitable conditions to ultra-trace elements with a sensitivity approaching that of the radiochemical methods.

Science.gov (United States)

The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of ...

International Nuclear Information System (INIS)

The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of ...

International Nuclear Information System (INIS)

The band structure (BS) of crystalline Bi_2Se_2Te both pure as well as deposited on Si or SiO_2 (substrates) was calculated for the first time. The calculation approach consists of an orthogonalization of the plane wave basis set with respect to the core-like orbitals and the application of the Perdew-Alder exchange-correlation scheme. In addition, a virtual crystal approach was applied. Experimental ellipsometric spectra were used as a criterion of the advantages of the different calculation techniques. The results of traditional one-electron methods of BS calculations, using norm-conserving pseudo-potential (NCPP), and full linear augmented plane wave (FLAPW), were compared with the experimental data. Better agreement with experiment is achieved when the NCPP wave functions are orthogonalized to the 4dBi core-like states. Concerning the LMTO and the FLAPW all-electron methods, only appropriate ...

Energy Technology Data Exchange (ETDEWEB)

Anomalous fading of the feldspar infrared stimulated luminescence (IRSL) signal hampers possibilities of using feldspar IRSL to obtain burial ages for sediments beyond the dating range of quartz optically stimulated luminescence. Here, we propose a new approach to quantify anomalous fading of the feldspar IRSL signal over geological burial times based on laboratory fading experiments. The approach builds on the description of the quantum mechanical tunnelling process recently proposed by Huntley [2006. An explanation of the power-law decay of luminescence. J. Phys. Condensed Matter 18, 1359-1365]. We show that our methods allow the construction of un-faded and natural IRSL dose-response curves as well as anomalous fading rates in field saturation. The predicted level of field saturation closely approximates the measured saturation level for five samples from fluvial deposits (Lower Rhine) known to be older than 1 Ma. The ...

Energy Technology Data Exchange (ETDEWEB)

Exceptional progress has been made in mathematical algorithm research leading to optimized mesh partitions for the highly unstructured grids occurring in finite element applications in solid mechanics. Today another research challenge presents itself. Research is needed to include boundary conditions into the algorithms for partitioning meshes. We describe below two methods we use currently to accomplish this and propose a more general approach be developed which would apply to our problems today as well as to the coupled models we envision for the future. Finally, we suggest research be considered that would incorporate partitioning methods into parallel mesh generation.

British Library Electronic Table of Contents (United Kingdom)

A one parameter family of iterative methods for the simultaneous approximation of simple complex zeros of a polynomial, based on a cubically convergent Hansen-Patricks family, is studied. We show that the convergence of the basic family of the fourth order can be increased to five and six using Newtons and Halleys corrections, respectively. Since these corrections use the already calculated values, the computational efficiency of the accelerated methods is significantly increased. Further acceleration is achieved by applying the Gauss-Seidel approach (single-step mode). One of the most important problems in solving nonlinear equations, the construction of initial conditions which provide both the guaranteed and fast convergence, is considered for the proposed accelerated family. These cond...

Energy Technology Data Exchange (ETDEWEB)

A decoupled characteristic between the damping of a specific swing mode and the stabilizer gain of the corresponding machine in multimachine power systems is identified. Using this decoupled characteristic a power system stabilizer (PSS) synthesis approach which is based on the phase compensation concept is verified on a 9-machine system and the dynamic performance of this system is significantly improved. This method is proved to be effective, simple and it can provide useful guidance for the PSS field tuning.

International Nuclear Information System (INIS)

27 cases including 7 outpatients, underwent intraarterial DSA using 4-F nylon catheter, by transbrachial arterial approach. Much of DSAs were performed in Fuji Computed Radiography (FCR), which has high spatial resolution. In all cases, image quality satisfied clinical demands. No major complication occured in this series. Transbrachial arterial digital subtraction angiography is excellent and safe method for screening of vascular disease. (author).

CERN Document Server

We derive the explicit formula for the joint Laplace transform of the Wishart process and its time integral which extends the original approach of Bru. We compare our methodology with the alternative results given by the variation of constants method, the linearization of the Matrix Riccati ODE's and the Runge-Kutta algorithm. The new formula turns out to be fast, accurate and very useful for applications when dealing with stochastic volatility and stochastic correlation modelling.

CERN Document Server

Given a random variable $F$ regular enough in the sense of the Malliavin calculus, we are able to measure the distance between its law and almost any continuous probability law on the real line. The bounds are given in terms of the Malliavin derivative of $F$. Our approach is based on the theory of It\\^o diffusions and the stochastic calculus of variations. Several examples are considered in order to illustrate our general results.

Energy Technology Data Exchange (ETDEWEB)

The four mines supplying the Sasol-2 plant at Secunda, South Africa are approaching their full production potential of 29 million t/year. Current production is 27.7 million t/year of coal for gasification and steam raising. Three mining methods are employed: bord and pillar, longwall and continuous mining. Details are given of the mining operations and machinery. A 43 km overland conveyor transports the coal to the Sasol plant stockpile.

Energy Technology Data Exchange (ETDEWEB)

This work presents a method to monitor the stability of a power system, after a major disturbance, using of adaptive time series approach. The model parameters are updated every time the prediction stage is completed. Besides, according to the values of the parameters, one may conclude the system will be unstable, will go to be a damped sine wave or even a damped exponential. (author) 29 refs., 12 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This paper examines the seismic signatures of discrete, finite-length fractures, and outlines an approach for elastic, prestack reverse-time imaging of discrete fractures. The results of this study highlight the importance of incorporating fracture-generated P-S converted waves into the imaging method, and presents an alternate imaging condition that can be used in elastic reverse-time imaging when a direct wave is recorded (e.g., for crosswell and VSP acquisition geometries).

Energy Technology Data Exchange (ETDEWEB)

Various physics applications involve the computation of the standard hypergeometric function {sub 2}F{sub 1} and its derivatives. Because it is not an intrinsic in the common programming languages, automatic differentiation tools will either differentiate through the code that computes {sub 2}F{sub 1} if that code is available or require the user to provide a hand-written derivative code. We present options for the derivative computation in the context of an ionization problem and compare the approach implemented in the Diamant library to standard methods.

CERN Document Server

We apply two variations of the principle of Minimum Cross Entropy (the Kullback information measure) to fit parameterized probability density models to observed data densities. For an array beamforming problem with P incident narrowband point sources, N > P sensors, and colored noise, both approaches yield eigenvector fitting methods similar to that of the MUSIC algorithm[1]. Furthermore, the corresponding cross-entropies are related to the MDL model order selection criterion[2].

Energy Technology Data Exchange (ETDEWEB)

An algebraic formulation of the electromagnetic field in which various quantization procedures can be described was chosen to discuss perturbation calculations. It is shown that the Feynman rules and the second order calculation of the self-energy of the electron can be developed on the basis of the Fermi method of quantization. The algebraic approach clarifies the problems in defining the vacuum and other states which are associated with calculations in terms of field algebra operators. It is demonstrated that the vacuum state defined on the field algebra by Schwinger leads to incorrect results in the self-energy calculation.

Energy Technology Data Exchange (ETDEWEB)

This report describes the method of Allan variance and its application to the characterization of a Ring Laser Gyro`s (RLG) performance. Allan variance, a time domain analysis technique, is an accepted IEEE standard for gyro specifications. The method was initially developed by David Allan of the National Bureau of Standards to quantify the error statistics of a Cesium beam frequency standard employed as the US Frequency Standards in 1960`s. The method can, in general, be applied to analyze the error characteristics of any precision measurement instrument. The key attribute of the method is that it allows for a finer, easier characterization and identification of error sources and their contribution to the overall noise statistics. This report presents an overview of the method, explains the relationship between Allan variance and power spectral density distribution of underlying ...

Energy Technology Data Exchange (ETDEWEB)

New partial differential equations (PDEs) for the full order weak schemes of the Langevin simulations are formulated. They are solved recursively in full order series solutions with respect to {radical}(t) (the full order weak Taylor schemes). Arbitrariness involved in the solutions is analyzed and clarified in detail. Specific solutions within some orders are presented as examples of the weak Taylor schemes. These PDEs and their solutions will serve for further developments of efficient higher order Runge-Kutta-like schemes. The similar formulation is possible for the imaginary time Hamiltonian evolution kernels as well. (orig.). 9 refs.

International Nuclear Information System (INIS)

Full text: Radiotherapy treatment planning (RTP) relies heavily on medical imaging. Until recently, the most important planning tool was the treatment simulator. The kilovoltage radiographic capabilities in a treatment simulator enabled the boundaries of treatment fields to be visualized with respect to bony anatomic landmarks. Perhaps the most important advance in treatment planning in recent years is the ability to visualize the passage of the beams with respect to a more accurate geometrical representation of the tumor and other soft tissue structures. This 'virtual simulation' uses a computer-based representation of a patient to determine the extent of the disease and the location of radiation sensitive normal tissue. Computer tomographic (CT) imaging produces a high-resolution three-dimensional representation of anatomy that can be correlated with other image sets such as magnetic resonance images (MRI) of function. Positron emission tomographic (PET) imaging is beginning to be ...

CERN Document Server

Similarity search

Energy Technology Data Exchange (ETDEWEB)

Certain innovative coke-oven repair techniques are reviewed that represent an engineered approach to a successful rehabilitation of all types of coke-oven batteries. These techniques have been developed during the last 10 years and experience gained on a number of repair projects has shown that these techniques operate as a cohesive and comprehensive method of end flue and through-wall repairs to gain additional years of operating life to coke-oven batteries. Extended operations approaching 10 to 15 additional years of service at lower costs than a pad-up rebuild and, while meeting the environmental emission regulations, are attainable using the techniques of: Proper tie-in joint preparation; Improved bricking up methodology; Preheating refractory during bricking up; Installation of spring-loaded bracing system; and installation of flexible coke-oven doors. Repair methods that do not incorporate the ...

British Library Electronic Table of Contents (United Kingdom)

Purpose The laparoscopic surgical approach to unilateral intra-abdominal testis has replaced the open approach at several large centers. There is considerable literature on experience with unilateral intra-abdominal testes but little on the management of bilateral intra-abdominal testes. We assessed the feasibility and safety of performing single setting bilateral laparoscopic orchiopexy in boys with bilateral intra-abdominal testes. Materials and Methods A single surgeon experience was reviewed. The surgical technique was similar in all cases and on each side, including infra-umbilical access, diagnostic evaluation, peritoneal mobilization lateral to the spermatic vessels and inferior to the vas deferens, gubernacular transection, and a decision for or against a Fowler-Stephens procedure ...

Energy Technology Data Exchange (ETDEWEB)

Wall thickness measurement of pipe is very important of the structural integrity of the industrial plant. However, the radiography method has an advantage because the ability of penetrating the insulated pipe. This will have economic benefit for industry. Moreover, the era of digital radiography has more advantages because the speed of radiographic work, less exposure time and no chemical used for film development. Either the conventional radiography or digital radiology, the wall thickness measurement is using the tangential radiography technique (TRT). In case, of a large diameter, pipe (more than inches) the determination maximum penetration wall thickness must be taken into the consideration. This paper is revisited the mathematical derivation of the determination of wall thickness measurement based on tangential radiography technique (TRT). The mathematical approach used in this derivation is the Pythagoras theorem and geometrical ...

CERN Document Server

The historical background of the 19th century electromagnetic theory is revisited from the standpoint of the opposition between alternative approaches in respect to the problem of interactions. The 19th century electrodynamics became the battle-field of a paramount importance to test existing conceptions of interactions. Hertz's experiments were designed to bring a solid experimental evidence in favor of one of them. The modern scientific method applied to analyze Hertz's experimental approach as well as the analysis of his laboratory notes, dairy and private letters show that Hertz's "\\textit{crucial}" experiments cannot be considered as conclusive at many points as it is generally implied. We found that alternative Helmholtz's electrodynamics did not contradict any of Hertz's experimental observations of transverse components as Maxwell's theory predicted. Moreover, as we now know from recently published Hertz's dairy ...

British Library Electronic Table of Contents (United Kingdom)

The problem of electrical parameters identification in complex systems, and in particular in electric railway traction systems, is considered. Parameters are determined by an indirect approach: only the terminal variables (voltages and currents and, impedance and admittance, which can be readily calculated) are measured and the per-unit-length electrical parameters are determined using a multiconductor transmission line model of the track section under test. It will be shown that some parameters cannot be measured directly, that they are not constant with frequency and that they may depend on other external conditions. An indirect method for parameters identification is proposed through an adaptive algorithm (AA), so that the calculated terminal variables match the measured ones. The AA is...

Energy Technology Data Exchange (ETDEWEB)

Competitive bidding for ancillary services (A/S), in addition to bidding for energy, is increasingly recognized as an important part of electricity markets. In this paper, an LP-based approach is presented for solving the multi-product (i.e. energy and A/S products), multi-zone/area physical market dispatch problem. The approach can explicitly represent various constraints, such as reserve requirement constraints, network security limits, and sharing of constrained resource capacity (e.g. maximum unit generation) between energy and reserve. The joint dispatch method, which dispatches energy and reserve market concurrently, is extended to allow inter-zonal reserve trading in multi-zone competitive pool. Numerical examples are included to demonstrate the salient characteristics of the joint dispatch solution.

British Library Electronic Table of Contents (United Kingdom)

Forced harmonic vibration of a non-uniform elastic beam with attached dynamic vibration absorbers (DVA) is studied. Analytical approximation of the solution is obtained by the functional perturbation method (FPM). The problem has application to cutting tools operations where the resistance of the tool holder against regenerative chatter can be enhanced by optimizing the real part of the frequency response function (FRF). A test case of a beam with step-like heterogeneity and single DVA at the tip shows that the FPM solution is very accurate for up to ?40 percent deviation in both stiffness and mass density. Using the analytical results and Sims approach, optimal DVA tuning is found for each set of beam heterogeneity parameters by solving a set of nonlinear algebraic equations numer...

CERN Document Server

The effective approach to quantum dynamics allows a reformulation of the Dirac quantization procedure for constrained systems in terms of an infinite-dimensional constrained system of classical type. For semiclassical approximations, the quantum constrained system can be truncated to finite size and solved by the reduced phase space or gauge-fixing methods. In particular, the classical feasibility of local internal times is directly generalized to quantum systems, overcoming the main difficulties associated with the general problem of time in the semiclassical realm. The key features of local internal times and the procedure of patching global solutions using overlapping intervals of local internal times are described and illustrated by two quantum mechanical examples. The choice of time is tantamount to a choice of gauge at the effective level and changing the clock is, therefore, equivalent to a gauge transformation. This article complements ...

British Library Electronic Table of Contents (United Kingdom)

Customer churn means the loss of existing customers to a competitor. Accurately predicting customer behavior may help firms to minimize this loss by proactively building a lasting relationship with their customers. In this paper, the application of the factor analysis and the Variable Consistency Dominance-based Rough Set Approach (VC-DRSA) in the customer relationship management (CRM) of the airline market is introduced. A set of "ifthen" decision rules are used as the preference model to classify customers by a set of criteria and regular attributes. The proposed method can determine the competitive position of an airline by understanding the behavior of its customers based on their perception of choice, and so develop the appropriate marketing strategies. A large sample of customers fro...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the graphical simulation of a traffic environment. The environment includes streets leading to an intersection, the intersection, vehicle traffic, and signal lights in the intersection controlled by different methods. The simulation allows for the study of parameters affecting traffic environments and the study of different control strategies for traffic signal lights, including conventional, fuzzy, and adaptive control methods. Realistic traffic environments are simulated including a cross intersection, with one or more lanes of traffic in each direction, with and without turn lanes. Vehicle traffic patterns are a mixture of cars going straight and making right or left turns. The free velocities of vehicles follow a normal distribution with a mean of the ``posted`` speed limit. Actual velocities depend on such factors as the proximity and velocity of surrounding traffic, approaches to intersections, ...

International Nuclear Information System (INIS)

The general development of variational methods for fusion reactor blanket studies is given. Important quantities such as tritium breeding ratio and total nuclear heating are linear functionals of the solutions to the Boltzmann transport equation. To estimate a neutronic quantity by variational methods is, in general, to carry out the scalar product formulation of the Roussopoulos variational principle, or the Schwinger variational principle, with the help of the associated adjoint transport equation where the appropriate response function for the estimate is taken as the source. A multipoint interpolation method based on the above variational principles has been developed and compared to other variational approaches. The method of variational interpolation removes the need to compute both forward and adjoint solutions while the error has the characteristic of cancellation of errors ...

International Nuclear Information System (INIS)

Energy savings from the use of daylighting in commercial buildings are realized through implementation of photoelectric lighting controls that dim electric lights when sufficient daylight is available to provide adequate workplane illumination. The dimming level of electric lighting is based on the signal of a photosensor. Current simulation approaches for such systems are based on the questionable assumption that the signal of the photosensor is proportional to the task illuminance. This paper presents a method that simulates the performance of photosensor controls considering the acceptance angle, angular sensitivity, placement of the photosensor within a space, and color correction filter. The method is based on the multiplication of two fisheye images: one generated from the angular sensitivity of the photosensor and the other from a 180- or 360-degree fisheye image of the space as ''seen'' by the photosensor. The paper ...

Energy Technology Data Exchange (ETDEWEB)

Radium is known to be taken up by aquatic animals, and tends to accumulate in bone, shell and exoskeleton. The most common approach to estimating the uptake of a radionuclide by aquatic animals for use in health and environmental risk assessments is the concentration factor method. The concentration factor method relates the concentration of a contaminant in an organism to the concentration in the surrounding water. Site specific data are not usually available, and generic, default values are often used in risk assessment studies. This paper describes the concentration factor method, summarizes some of the variables which may influence the concentration factor for radium, reviews reported concentration factors measured in marine environments and presents concentration factors derived from data collected in a study in coastal Louisiana. The use of generic default values for the concentration factor is ...

British Library Electronic Table of Contents (United Kingdom)

Abstract: The recent National Academy of Sciences report on forensic sciences states that the study of fire patterns and debris in arson fires is in need of additional work and eventual standardization. We discuss a recently introduced method that can provide predicted evaporation patterns for ignitable liquids as a function of temperature. The method is a complex fluid analysis protocol, the advanced distillation curve approach, featuring a composition explicit data channel for each distillate fraction (for qualitative, quantitative, and trace analysis), low uncertainty temperature measurements that are thermodynamic state points that can be modeled with an equation of state, consistency with a century of historical data, and an assessment of the energy content of each distillate fraction...

Energy Technology Data Exchange (ETDEWEB)

The present paper describes the application of the commercial CFD-code FLUENT 6.1 to the numerical simulation of the flow field in a high specific speed radial fan. Two-dimensional as well as three-dimensional computations are performed using the steady 'Frozen-Rotor method' as well as the unsteady 'Sliding-Mesh method'. The predicted performance curves of the radial fan are compared with the results obtained from measurements on a test stand. Due to the relatively low computation times, the 'Frozen-Rotor method' can be used routinely for design purposes. The results of this approach can be improved if the leakage flow through the gap between the inlet nozzle and the impeller is taken into account. (orig.)

Science.gov (United States)

A new approach of gear fault diagnosis based on continuous wavelet transform is presented. Continuous wavelet transform can provide a finer scale resolution than orthogonal wavelet transform. It is more suitable for extracting mechanical fault information. In this paper, the concept of time-averaged wavelet spectrum (TAWS) based on Morlet continuous wavelet transform is proposed. Two fault diagnosis methods named spectrum comparison method (SCM) and feature energy method (FEM) based on TAWS are established. The results of the application to gearbox gear fault diagnosis show that TAWS can effectively extract gear fault information. The feature energy of the TAWS features the gear fault advancement very well and is conically proportional to the gear fault advancement.

International Nuclear Information System (INIS)

The Environmental Management System (EMS) is an instrument to manage the interaction between the organization and the environment. The scope od EMS is to reduce the environmental impact and to achieve improvements in overall performances. In particular, the focus point of EMS implementation is the method for identifying and assessing significant environmental aspects. The results of the literature and regulation reviews (Perotto 2006) have shown that rigourous repeatable and transparent methodologies do not exist. This paper presents a proposal method for identifying and assessing significant environmental aspects, that has all three of these important characteristics. In particular, the proposal methodology for assessing aspects is based on some criteria that are combined in a specific algorithm. It is important to specify that to make a correct application of the method a preliminary rigorous approach ...

Energy Technology Data Exchange (ETDEWEB)

Five corrosion probes were received from West Valley Nuclear Services for evaluation in simulated tank 8D-2 3rd-stage sludge wash slurry. The same waste slurry simulated was also used in a series of ongoing corrosion studies assessing the effects of in-tank sludge washing on the integrity of tank 8D-2. Two of the corrosion probes were installed in the coupon corrosion test vessels operating at {approximately}150{degrees}F to compare performance of the probes with that observed by coupon tests conducted in the same vessels. Corrosion rate data calculated from electrical resistance measurements of the corrosion probes were evaluated for this study using two slightly different approaches. One approach uses the total length of exposure of the probe to give a ``time-averaged`` value of the corrosion rate. The other approach uses a shorter period of time (relative to the length of the test) in the calculation of corrosion rate, ...

DEFF Research Database (Denmark)

It is possible to slow down the progression of Alzheimer's disease with pharmacological treatment. When this treatment is given to people with types of dementia that affect the frontal and temporal lobes (Frontotemporal Dementia) the results are discouraging. It is observed that the patients show pronounced restlessness and mania. In this article we describe a nonpharmacological psychosocial approach, music therapy, and how it is possible to work with this method when constitutional, regulative, dialogical, and integrative aspects are included. The focus is on therapeutic singing where well-known songs are applied in order to build up structure and stability and/or as means of arousal regulation. Songs with personal meaning make it possible to acknowledge the person's emotions, breaking the social isolation, and meeting the music therapy participant's psychosocial needs. The clinical approach is an integration of a ...

Energy Technology Data Exchange (ETDEWEB)

The usual method of introducing engineers to the concept of dislocations and their role in plastic flow is to compare an estimate of the theoretical strength of solid (of order {micro}/30 where {micro} is the shear modulus) and the observed strength of either single crystals ({mu}/10{sup 4}) or practical engineering material such as structural steels where the yield stress in shear is of order {mu}/10{sup 3}. However, if one considers the problem in reverse, one can consider the accumulation of dislocations as an important mechanism by which one can produce engineering materials in which the strength level approaches the theoretical strength. If one assumes that the flow stress can be expressed in terms of te mean free path between stored dislocations or as the square root of the global dislocation density, then one can see the influence of dislocation density in a diagrammatic form. It is clear that the strengthening by dislocation ...

Energy Technology Data Exchange (ETDEWEB)

The overall goal of the proposed project is to explore the use of partitioning tracers to characterize dense nonaqueous phase liquids (DNAPLs) in aquifer systems. Bulk-phase partitioning tracers will be investigated to detect and determine DNAPL saturation, while interface partitioning tracers will be investigated to measure the area of the DNAPL-water interface. The specific objectives that will be addressed to accomplish this goal are: (1) Investigate the use of partitioning tracers to detect and determine both the saturation and interfacial area of DNAPLs in saturated porous media. (2) Investigate the effect of rate-limited mass transfer on the transport behavior of partitioning tracers. (3) Investigate the effect of porous-media heterogeneity on the transport behavior of partitioning tracers. (4) Develop and evaluate mathematical models capable of simulating the transport of partitioning tracers in complex systems. This proposal outlines an integrated approach ...

Energy Technology Data Exchange (ETDEWEB)

Background and purpose: the recent RTOG guidelines for future clinical developments in gynecologic malignancies included the investigation of dose escalation in the paraaortic (PO) region which is, however, very difficult to target due to the presence of critical organs such as kidneys, liver, spinal cord, and digestive structures. The aim of this study was to investigate intensity-modulated radiotherapy's (IMRT) possibilities of either increasing, in a safe way, the dose to 50-60 Gy in case of macroscopic disease or decreasing the dose to organs at risk (OR) when treatment is given in an adjuvant setting. Material and methods: the dosimetric charts of 14 patients irradiated to the PO region at the department of radiation oncology, university hospital of Liege, Belgium, in 2000 were analyzed in order to compare six-field conformal external-beam radio-therapy (CEBR) and five-beam IMRT approaches. Both CEBR and IMRT investigations were ...

Energy Technology Data Exchange (ETDEWEB)

There are several methods for the risk assessment and risk management applied to pipelines, among them the Muhlbauer's Method. W. Kent Muhlbauer is an internationally recognized authority on pipeline risk management. He made a detailed identification about 300 distinct conditions that influence the risk assessment in pipelines and he proposed a score system that is known as method of Muhlbauer. The purpose of this model is to evaluate the public exposure to the risk and identify ways for management that risk in fact. The assessment is made by the attribution of quantitative values to the several items that influences in the pipeline risk. This paper approaches the Muhlbauer's basic model for risk assessment and management in pipelines. In the beginning, the basic model for risk assessment is presented, and methodology for pipelines in onshore environment is detailed. After, presents ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to present a summary of new methods, employing Lie algebraic tools, for characterizing beam dynamics in charged-particle optical systems. These methods are applicable to accelerator design, charged-particle beam transport, electron microscopes, and also light optics. The new methods represent the action of each separate element of a compound optical system, including all departures from paraxial optics, by a certain operator. The operators for the various elements can then be concatenated, following well-defined rules, to obtain a resultant operator that characterizes the entire system. This paper deals mostly with accelerator design and charged-particle beam transport. The application of Lie algebraic methods to light optics and electron microscopes is described elsewhere (1, see also 44). To keep its scope within reasonable bounds, they restrict their treatment of ...

International Nuclear Information System (INIS)

Construction and commissioning period of NPP are reduced world over drastically by stringent schedule for financial and economic reasons. For meeting the schedule, commissioning of components and systems are started immediate after installation, while construction activities are continued in parallel at the same place. Parallel activities' and 'Time Constraint' have brought new challenges to 'Management of Fire and Industrial Safely' during commissioning. An innovative approach was used during such phase of commissioning of TAPP-3 and 4. This paper outlines challenges encountered during this phase and special approach and measures used to meet those challenges. This paper also outlines problems encountered during implementation of these measures and subsequent change in approach to ensure smooth and safe execution of activities. Primarily, challenges were conflicting requirements by various agencies to carryout ...

Energy Technology Data Exchange (ETDEWEB)

Canada's oil sands contain the largest known reserve of oil in the world. Oil sands mining uses 3 functional processes, ore hauling, overburden removal and mechanical maintenance. The industry relies mainly on truck-and-shovel technology in its open-pit mining operations which contributes greatly to the overall mining operation cost. Coordination between operating units is crucial for achieving an enterprise-wide optimal operation level. Some of the challenges facing the industry include multiple or conflicting objectives such as minimizing the use of raw materials and energy while maximizing production. The large sets of constraints that define the feasible domain pose as challenge, as does the uncertainty in system parameters. One solution lies in assigning truck resources to various activities. This fully decentralized approach would treat the optimization of ore production, waste removal and equipment maintenance independently. It was emphasized that ...

Science.gov (United States)

A stochastic linear fractional programming (SLFP) approach is developed for supporting sustainable municipal solid waste management under uncertainty. The SLFP method can solve ratio optimization problems associated with random information, where chance-constrained programming is integrated into a linear fractional programming framework. It has advantages in: (1) comparing objectives of two aspects, (2) reflecting system efficiency, (3) dealing with uncertainty expressed as probability distributions, and (4) providing optimal-ratio solutions under different system-reliability conditions. The method is applied to a case study of waste flow allocation within a municipal solid waste (MSW) management system. The obtained solutions are useful for identifying sustainable MSW management schemes with maximized system efficiency under various constraint-violation risks. The results indicate that SLFP can support in-depth analysis of ...

Energy Technology Data Exchange (ETDEWEB)

One- and two-dimensional long-period superstructures (LPS), based on the L1{sub 2} substructure, are systematically investigated for the noble metal-palladium alloys Cu-Pd, Ag-Pd and Au-Pd with first-principles methods. Notwithstanding the fact that the experimental phase diagrams of these systems yield totally different features, quite similar behaviour with respect to formation of low temperature ordered LPS-phases (Cu{sub 3}Pd: LPS 3, Ag{sub 3}Pd: LPS 3, Au{sub 3}Pd: LPS 2; {l_brace}Cu, Au{r_brace}Pd{sub 3}: L1{sub 2}, AgPd{sub 3}: not a ground state) is predicted. As a lever between via LDA obtained formation enthalpies and a thorough ground state scan, the cluster expansion method in conjunction with a genetic algorithm provides adequate means for the extraction of effective interactions, which also allow for an enhanced ground state scan in the configurational space of LPS structures. As a result, the sequences and energetical hierarchies ...

CERN Document Server

This paper is focused on solving the narrowband direction of arrival estimation problem from a sparse signal reconstruction perspective. Existing sparsity-based methods have shown advantages over conventional ones but exhibit limitations in practical situations where the true directions are not in the sampling grid. A so-called off-grid model is broached to reduce the modeling error caused by the off-grid directions. An iterative algorithm is proposed in this paper to solve the resulting problem from a Bayesian perspective while joint sparsity among different snapshots is exploited by assuming the same Laplace prior. Like existing sparsity-based methods, the new approach applies to arbitrary sensor array and exhibits increased resolution and improved robustness to noise and source correlation. Moreover, our approach results in more accurate direction of arrival estimation, e.g., smaller bias and lower ...

Energy Technology Data Exchange (ETDEWEB)

This paper is a result of a research with the primary purpose of extending Probabilistic Risk Assessment (PRA) modeling frameworks to include the effects of organizational factors as the deeper, more fundamental causes of accidents and incidents. There have been significant improvements in the sophistication of quantitative methods of safety and risk assessment, but the progress on techniques most suitable for organizational safety risk frameworks has been limited. The focus of this paper is on the choice of 'representational schemes' and 'techniques.' A methodology for selecting appropriate candidate techniques and their integration in the form of a 'hybrid' approach is proposed. Then an example is given through an integration of System Dynamics (SD), Bayesian Belief Network (BBN), Event Sequence Diagram (ESD), and Fault Tree (FT) in order to demonstrate the feasibility and value of hybrid ...

International Nuclear Information System (INIS)

The calculation of nominal choke valve size determines the effective capacity for an oil and gas production system. The degree of restriction for the controlling area in the valve is a function of the surrounding geometry. In an orifice plate this is known as the 'velocity of approach' and can be used to determine the meter coefficient (C_m). This paper presents a technique for choke valves, based on the meter velocity of approach parameter, which can be used to predict the Valve Coefficient (C_v) for new trim designs. The prediction method uses a data trend based on a number of flow tests conducted on various trim characteristics. The resultant parametric equation is used to predict the C_v of a new trim geometry. The method relies on experimental data determined per IEC 60534-2-3, with calculations per IEC 60534-2-1. This paper further investigates the effect of varying upstream geometry on C_v for a ...

Energy Technology Data Exchange (ETDEWEB)

Background: the authors report on the conception and first clinical application of a donut-shaped high-dose configuration for proton therapy (PT). This approach allows one to intensify target volume dose coverage for targets encompassing a critical, dose-limiting structure - like here, the cauda equina -, whilst delivering minimal dose to other healthy structures surrounding the target, thereby reducing the integral dose. Methods and results: intensity-modulated PT methods (IMPT) for spot scanning were applied to create and deliver a donut-shaped high-dose configuration with protons, allowing treating > 75% of the target with at least 95% of the prescribed dose of 72.8 CGE, whilst restricting dose to the cauda equina to 60-65 CGE. Integral dose was lower by a factor of 3.3 as compared to intensity-modulated radiotherapy with photons (IMXT). Conclusion: IMPT and spot scanning technology allow a potentially clinically ...

Science.gov (United States)

The current status of a computational aeroacoustics (CAA) approach to simulate broadband noise is reviewed. The method rests on the use of steady Reynolds averaged Navier-Stokes (RANS) simulation to describe the time-averaged motion of turbulent flow. By means of synthetic turbulence the steady one-point statistics (e.g. turbulence kinetic energy) and turbulent length- and time-scales of RANS are translated into fluctuations having statistics that very accurately reproduce the initial RANS target-setting. The synthetic fluctuations are used to prescribe sound sources which drive linear perturbation equations. The whole approach represents a methodology to solve statistical noise theory with state-of-the-art CAA tools in the time-domain. A brief overview of the synthetic turbulence model and its numerical discretization in terms of the random particle-mesh (RPM) and fast random particle-mesh (FRPM) ...

Energy Technology Data Exchange (ETDEWEB)

We review the development and application of kinetic Monte Carlo simulations to investigate defect and dopant diffusion in ion implanted silicon. In these type of Monte Carlo models, defects and dopants are treated at the atomic scale, and move according to reaction rates given as input principles. These input parameters can be obtained from first principles calculations and/or empirical molecular dynamics simulations, or can be extracted from fits to experimental data. Time and length scales differing several orders of magnitude can be followed with this method, allowing for direct comparison with experiments. The different approaches are explained and some results presented.

International Nuclear Information System (INIS)

Using an ab initio pseudopotential method within a generalized gradient approximation of the density functional theory, the structural, electronic, and phonon properties of SrS in the B1 (NaCl) and B2 (CsCl) structures have been studied. The calculated lattice constants, static bulk modulus, and first-order pressure derivative of the bulk modulus are reported for both the B1 and B2 structures and compared with previous experimental and theoretical calculations. Electronic band structures and densities of states have been derived for SrS. Subsequently, a linear-response approach to the density functional theory is used to derive the phonon frequencies and densities of states.

Energy Technology Data Exchange (ETDEWEB)

Sol-gel chemistry has a great many potential applications in the preparation of unique electrochemical materials, from non-equilibrium transition metal oxides which may be of use as high energy density electrodes, to high-surface area mixed oxides which may possess high proton conductivity, to novel composite structures consisting of inorganic gels in combination with organic, electronic, and ionic conductors. This paper reviews prior work on proton conduction in gel systems and presents recent work regarding electrode materials prepared by sol-gel methods and inorganic-organic materials.

British Library Electronic Table of Contents (United Kingdom)

Introduction Gastrointestinal bleeding is a common life-threatening problem, causing significant mortality, costs and resource allocation. Its management requires a dynamic multidisciplinary approach that directs diagnostic and therapeutic priorities appropriately. Materials and methods Articles published within the past 15 years, related to gastrointestinal bleeding, were reviewed through MEDLINE search, in addition to current guidelines and standards. Results Decisions of ICU admission and blood transfusion must be individualized based on the extent of bleeding, hemodynamic profile and comorbidities of the patient and the risk of rebleeding. A secure airway may be required to optimize oxygenation and to prevent aspiration. Doses of induction agents must be reduced due to the changes in v...

Energy Technology Data Exchange (ETDEWEB)

The various technical aspects of radon concentration measurements in the ground or in the groundwater are reviewed. The emphasis is put on the most convenient techniques particularly suited for in situ monitoring in the field. Some attention is paid to the thoron problem. Historical and most recent findings in the field or earthquake related radon anomalies are presented and briefly discussed. A similar approach is made to rarer volcanic cases that have been documented up to now. A short discussion regarding the various models that intend to provide satisfactory explanations is presented, supported, whenever it is possible, by experimental laboratory results. Finally a glimpse on the possible and future application of the method to hydrogeology is given. (orig.).

British Library Electronic Table of Contents (United Kingdom)

Simplified strain-based fracture mechanics equations, established for external surface cracked pipelines subjected to an external bending load, are presented and used in probabilistic assessment of a pipeline girth weld. The model takes into account several parameters, such as variation in crack depth, crack length, internal pressure and material hardening. The critical strain from ductile tearing in the cracked pipeline is found by using the tangency criterion. The reliability problem is solved using first and second order reliability methods for different pipe dimensions and load levels.

CERN Document Server

We propose a new approach to study Koszul cohomology of general $g^r_d$'s on general curves via degenerations and deformations. As an application of this new method, we prove projective normality for general line bundles $L$ on general curves with $h^1(L)\\le1$ and degree greater than roughly $(5/4)g$. This improves the bound in a classical theorem of Green and Lazarsfeld. Also we give some partial results on vanishing of higher syzygies for line bundles with $h^1(L)=1$.

CERN Document Server

The possibility of the existence of stable tetrahedral deformations at spin zero is investigated using the Skyrme-HFBCS approach and the generator coordinate method (GCM). The study is limited to nuclei in which the tetrahedral mode has been predicted to be favored on the basis of non self-consistent models. Our results indicate that a clear identification of tetrahedral deformations is unlikely as they are strongly mixed with the axial octupole mode. However, the excitation energies related to the tetrahedral mode are systematically lower than those of the axial octupole mode in all the nuclei included in this study.

International Nuclear Information System (INIS)

A theoretical study of structural and electronic properties of GeC, SnC and GeSn is presented using the full potential linearized augmented plane wave method. In this approach, the generalized gradient approximation was used for the exchange-correlation potential. Results are given for lattice constant, bulk modulus and its pressure derivative in both zinc-blende and rocksalt structures. Band structure, density of states and band gap pressure coefficients in zinc-blende structure are also given. The results are compared with previous calculations and with experimental measurements.

Energy Technology Data Exchange (ETDEWEB)

Absorption with aqueous amine solvents is at present the most viable technology for CO{sub 2} capture. While this is a proven technology, efforts are ongoing to improve it in order to make it a more attractive technology for large scale use to reduce CO{sub 2} emissions. Finding solvents with better properties is one approach to improving the technology. In this thesis methods in computational chemistry are used to improve the understanding of the chemistry of CO{sub 2} absorption in amine-water systems. The work is also intended to provide models that can be used to predict the performance of new solvents. Such predictive models are intended to facilitate the screening for new solvents

British Library Electronic Table of Contents (United Kingdom)

The algorithmic, or consistent, tangent stiffness was introduced to improve the asymptotic convergence rate of the iterative correction algorithm for the evolutive analysis of elastoplastic structures. The original approach is based on a formulation of the elastoplastic law in terms of a plastic multiplier with an analysis which, in general, requires an operator inversion. A geometric description of the method, based on hypersurface theory, is proposed here to provide a clear picture of the algorithmic properties. An estimate of the tangent stiffness associated with finite step elastoplastic and elastoviscoplastic constitutive models is given. It is based on the properties of the projection operator on the elastic domain and avoids operator inversions retaining the beneficial properties of...

British Library Electronic Table of Contents (United Kingdom)

Purpose - The purpose of this paper is to evaluate the corrosion inhibition potential of mangrove (Rhizopora apiculata) tannin in hydrochloric acid medium on copper with the view of developing a natural corrosion inhibitor. Design/methodology/approach - The mangrove tannin was extracted from the mangrove bark and its anticorrosion potential was studied by weight loss, electrochemical and scanning electron microscopy (SEM) analysis. Findings - It has been found that the mangrove tannin effectively inhibits the corrosion on copper metal in hydrochloric acid solution. The results of the electrochemical and weight loss methods showed that the inhibition efficiency of mangrove tannin increases with increasing its concentration. Inhibition is achieved through the adsorption of tannin molecules o...

CERN Document Server

This paper describes an effective unsupervised speaker indexing approach. We suggest a two stage algorithm to speed-up the state-of-the-art algorithm based on the Bayesian Information Criterion (BIC). In the first stage of the merging process a computationally cheap method based on the vector quantization (VQ) is used. Then in the second stage a more computational expensive technique based on the BIC is applied. In the speaker indexing task a turning parameter or a threshold is used. We suggest an on-line procedure to define the value of a turning parameter without using development data. The results are evaluated using 10 hours of audio data.

British Library Electronic Table of Contents (United Kingdom)

This paper defines homometry in the rather general case of locally-compact topological groups, and proposes new cases of its musical use. For several decades, homometry has raised interest in computational musicology and especially set-theoretical methods, and in an independent way and with different vocabulary in crystallography and other scientific areas. The link between these two approaches was only made recently, suggesting new interesting musical applications and opening new theoretical problems. We present some old and new results on homometry, and give perspective on future research assisted by computational methods. We assume from the reader's basic knowledge of groups, topological groups, group algebras, group actions, Lebesgue integration, convolution products, and Fourier trans...

Energy Technology Data Exchange (ETDEWEB)

A general method for stable-isotope labeling of large proteins is introduced and applied for studies of the E. coli GroE chaperone proteins by solution NMR. In addition to enabling the residue-specific {sup 15}N-labeling of proteins on a highly deuterated background, it is also an efficient approach for uniform labeling. The method meets the requirements of high-level deuteration, minimal cross-labeling and high protein yield, which are crucial for NMR studies of structures with sizes above 150 kDa. The results obtained with the new protocol are compared to other strategies for protein labeling, and evaluated with regard to the influence of external factors on the resulting isotope labeling patterns. Applications with the GroE system show that these strategies are efficient tools for studies of structure, dynamics and intermolecular interactions in large supramolecular complexes, when combined with TROSY- and CRINEPT-based ...

British Library Electronic Table of Contents (United Kingdom)

The utilization of thermal fluctuations or Johnson/Nyquist noise as a spectroscopic method to determine transport properties in conductors or semiconductors is developed. The autocorrelation function is obtained from power spectral density measurements thus enabling electronic transport property calculation through the Green-Kubo formalism. This experimental approach is distinct from traditional numerical methods such as molecular dynamics simulations, which have been used to extract the autocorrelation function and directly related physics only. This work reports multi-transport property measurements consisting of the electronic relaxation time, resistivity, mobility, diffusion coefficient, electronic contribution to thermal conductivity and Lorenz number from experimental data. Double va...

International Nuclear Information System (INIS)

We consider a SQUID ring inductively coupled to an electromagnetic field mode, both treated quantum mechanically. We demonstrate a method for creating a maximally entangled state between the ring and the field mode. Our method utilises a non-adiabatic external magnetic flux pulse to move into and out of a transition region. Hence, our approach is fundamentally different to techniques based on Landau-Zener tunnelling that can also be used to achieve similar results. Our analysis is extended to include the effects of coupling the system to a dissipative environment. With this model we show that although such an environment makes a noticeable difference to the time evolution of the system, it need not destroy the entanglement of this coupled system over time scales required for quantum technologies.

British Library Electronic Table of Contents (United Kingdom)

Background Stimulated by the concept of Natural Orifice Transluminal Endoscopic Surgery (NOTES), minimizing the access even further has become a new trend in minimally invasive surgery. We compare our recently described new method of endoscopic single-access adrenalectomy with the conventional retroperitoneoscopic approach in a matched-pairs study. Methods Fifty single-access retroperitoneoscopic adrenalectomies (SARA) were performed in 47 selected patients suffering from Conn?s adenomas (n?=?20), pheochromocytomas (n?=?15), Cushing?s adenomas (n?=?6), and other diseases (n?=?6). For SARA, a single 2-cm skin incision beneath the 12th rib was used. Following creation of the retroperitoneal space with the rigid endoscope, dissection was carried out single-handed. Another 47 patients served a...

CERN Document Server

The point-splitting regularization technique for composite operators is discussed in connection with anomaly calculation. We present a pedagogical and self-contained review of the topic with an emphasis on the technical details. We also develop simple algebraic tools to handle the path ordered exponential insertions used within the covariant and non-covariant version of the point-splitting method. The method is then applied to the calculation of the chiral, vector, trace, translation and Lorentz anomalies within diverse versions of the point-splitting regularization and a connection between the results is described. As an alternative to the standard approach we use the idea of deformed point-split transformation and corresponding Ward-Takahashi identities rather than an application of the equation of motion, which seems to save the complexity of the calculations.

International Nuclear Information System (INIS)

Background vibration in a CANDU plant can be used to determine the dynamic characteristics of major items of equipment, such as calandria, the fuelling machines and the primary heat transport pumps. These dynamic characteristics can then be used to verify the seismic response of the equipment which, at present, is based on theoretical models only. The feasibility and basic theory of this new approach (which uses accelerations measured at several points on a structure and does not require knowledge of the source of excitation) was established in Phase I of the study. This report is based on Phase II in which the methods of analysis developed in Phase I were improved and verified experimentally. A Fast Fourier Transform (FFT) algorithm was incorporated and an interactive curve fitting technique was developed to obtain the dynamic characteristics in the form of natural frequencies, mode shapes and damping ratios. The method is ...

British Library Electronic Table of Contents (United Kingdom)

The diversity of plant resources in the Brazilian semi-arid region is being compromised by practices related to agriculture, pastures, and forest harvesting, especially in areas containing Caatinga vegetation (xeric shrublands and thorn forests). The impact of these practices constitutes a series of complex factors involving local issues, creating a need for further scientific studies on the social-environmental dynamics of natural resource use. Through participatory methods, the present study analyzed people?s representations about local environmental change processes in the Brazilian semi-arid region, taking into consideration local production systems, natural resources, and their importance. Environmental historical graphs were developed with nine local families to analyze landscape cha...

British Library Electronic Table of Contents (United Kingdom)

Eddy current testing is one of the most widely used methods in non-destructive testing for the inspection of conductive materials. Numerical modelling of eddy current testing has emerged as an important approach alongside experimental studies. This paper investigates an application of numerical modelling and experimental study as a means of the quantitative non-destructive evaluation (QNDE) of defects in conductive samples. There are two methods of measuring eddy current response, more commonly by measuring the change in impedance of the eddy current probe coil, or as used in this work, by measuring the change in magnetic field directly using magnetic field sensors such as superconducting quantum interference devices, giant magneto resistance, or as in this case Hall sensors. Specifically,...

Energy Technology Data Exchange (ETDEWEB)

Knowledge is a success factor for globally acting company networks as a. o. the aim-oriented knowledge transfer between partners is an essential condition for a successful cooperation. Several network specific problems impede however an efficient and effective knowledge management; e.g. the transfer of competition relevant data is a high sensitive theme. The authors describe how a relevant method can be selected, adapted and implemented to the application-specific boundary conditions. They integrate existing attempts processes and methods to establish an effective knowledge development and an efficient knowledge transfer in the network and take into account ''hard'' (IT-technical-oriented solution approaches) as also ''soft'' factors (e.g. cultural and personal aspects). So the authors present unified instruments for an integrated knowledge management ...

Energy Technology Data Exchange (ETDEWEB)

While it is difficult to prove that a specific material is causing contamination in a landfill, tests have been conducted at waste-to-energy facilities that indicate that household batteries contribute significant amounts of heavy metals to both air emissions and ash residue. Hennepin County, MN, used a dual approach for developing and implementing a special household battery collection. Alternative collection methods were examined; test collections were conducted. The second phase examined operating and disposal policy issues. This report describes the results of the grant project, moving from a broad examination of the construction and content of batteries, to a description of the pilot collection programs, and ending with a discussion of variables affecting the cost and operation of a comprehensive battery collection program. Three out-of-state companies (PA, NY) were found that accept spent batteries; difficulties in reclaiming household ...

CERN Document Server

Strong gravitational lensing of an extended object is described by a mapping from source to image coordinates that is nonlinear and cannot generally be inverted analytically. Determining the structure of the source intensity distribution also requires a description of the blurring effect due to a point spread function. This initial study uses an iterative gravitational lens modeling scheme based on the semilinear method to determine the linear parameters (source intensity profile) of a strongly lensed system. Our 'matrix-free' approach avoids construction of the lens and blurring operators while retaining the least squares formulation of the problem. The parameters of an analytical lens model are found through nonlinear optimization by an advanced genetic algorithm (GA) and particle swarm optimizer (PSO). These global optimization routines are designed to explore the parameter space thoroughly, mapping model degeneracies in detail. We develop a ...

International Nuclear Information System (INIS)

Electronic structure, volume optimization, bulk moduli, elastic constants, and frequencies of the transversal optical vibrations in LiH, NaH, KH, RbH, and CsH are calculated using the full potential augmented plane wave method, extended with local orbitals, and the full potential linearized augmented plane wave method. The obtained results show some common features in the electronic structure of these compounds, but also clear differences, which cannot be explained using simple empirical trends. The differences are particularly prominent in the electronic distributions and interactions in various crystallographic planes. In the light of these findings we have elaborated some selected experimental results and discussed several theoretical approaches frequently used for the description of various alkali hydride properties.

British Library Electronic Table of Contents (United Kingdom)

New nanofibers containing poly(vinyl pyrrolidone)-iodine complex (PVP-iodine) were obtained by electrospinning in order to prepare materials suitable for wound dressings. Different approaches were used: a one-step method based on electrospinning of PVP-iodine or poly(ethylene oxide)/PVP-iodine solutions and a three-step method based on electrospinning of PVP or poly(ethylene oxide)/PVP mixed solutions followed by photo-mediated crosslinking of the obtained nanofibers and subsequent complexation with iodine. The average diameters of the fibers were in the range 150-470nm depending on the composition and on the applied field strength (AFS) and increased with increasing the amount of PEO in the spinning solutions. Higher AFS resulted in greater fiber diameter and in size distribution broadeni...

International Nuclear Information System (INIS)

Isotropic Compton profiles of TaC and TaN have been measured for the first time, at an intermediate resolution, using 662 keV #gamma#-radiation. Energy bands, density of states and Fermi surface topology of TaC and TaN have been computed using linear combination of atomic orbitals with density functional theory and full potential linearised augmented plane wave method. Both band structure calculations predict the metallic character of TaC and TaN. The electron momentum densities calculated using various approaches of density functional theory are compared with the present measurements. On the basis of Mulliken's population, it is also seen that TaC has more covalent bonding than TaN. The optical properties computed using full potential linearised augmented plane wave method are explained in terms of intraband transitions.

Energy Technology Data Exchange (ETDEWEB)

The Eddy covariance technique allows to measure different components of turbulent air fluxes, including the flow of water vapour. Sap flux measurements determine directly the water flow in tree stems. We compared the water flux just above the crowns of trees in a forest by the technique of Eddy covariance and the water flux by the xylem sap flux method. These two completely different approaches showed a good qualitative correspondence. The correlation coefficient is 0.8. With an estimation of the crown diameter of the measured tree we also find a very good quantitative agreement. (author) 3 figs., 5 refs.

CERN Document Server

A prescription is given for computing anomalous dimensions of single trace operators in SYM at strong coupling and large $N$ using a reduced model of matrix quantum mechanics. The method involves treating some parts of the operators as "BPS condensates" which, in certain limit, have a dual description as null geodesics on the $S^5$. In the gauge theory, the condensate is similar to a representative of the chiral ring and it is described by a background of commuting matrices. Excitations around these condensates correspond to excitations around this background and take the form of ``string bits" which are dual to the "giant magnons" of Hofman and Maldacena. In fact, the matrix model approach gives a {\\it quantum} description of these string configurations and explains why the infinite momentum limit suppresses the quantum effects. This method allows, not only to derive part of the classical sigma model Hamiltonian of the ...

British Library Electronic Table of Contents (United Kingdom)

Background: Cardio-respiratory interactions are weak at the earliest stages of human development, suggesting that assessment of their presence and integrity may be an important indicator of development in infants. Despite the valuable research devoted to infant development, there is still a need for specifically targeted standards and methods to assess cardiopulmonary functions in the early stages of life. We present a new methodological framework for the analysis of cardiovascular variables in preterm infants. Our approach is based on a set of mathematical tools that have been successful in quantifying important cardiovascular control mechanisms in adult humans, here specifically adapted to reflect the physiology of the developing cardiovascular system.Methods: We applied our methodology ...

CERN Document Server

Heterogeneous anisotropic diffusion problems arise in the various areas of science and engineering including plasma physics, petroleum engineering, and image processing. Standard numerical methods can produce spurious oscillations when they are used to solve those problems. A common approach to avoid this difficulty is to design a proper numerical scheme and/or a proper mesh so that the numerical solution validates the discrete counterpart (DMP) of the maximum principle satisfied by the continuous solution. A well known mesh condition for the DMP satisfaction by the linear finite element solution of isotropic diffusion problems is the non-obtuse angle condition that requires the dihedral angles of mesh elements to be non-obtuse. In this paper, a generalization of the condition, the so-called anisotropic non-obtuse angle condition, is developed for the finite element solution of heterogeneous anisotropic diffusion problems. The new condition is ...

British Library Electronic Table of Contents (United Kingdom)

We have recently introduced several important improvements in the measurement of distillation curves for complex fluids. This new method is a significant improvement over current approaches, with features including a composition-explicit data channel for each distillate fraction (for both qualitative and quantitative analysis), trace chemical analysis of each distillate fraction, and a corrosivity assessment of each distillate fraction. In the present contribution, we present the application of the advanced distillation curve method to a bio-derived crude oil prepared from swine manure. One motivation behind the work was to precisely measure the distillation curve of the oil derived from swine manure with our advanced distillation apparatus and compare the bio-derived oil to traditional pe...

Energy Technology Data Exchange (ETDEWEB)

Environmental exposure measurements are, in general, positive and may be subject to left censoring; i.e,. the measured value is less than a ''detection limit''. In occupational monitoring, strategies for assessing workplace exposures typically focus on the mean exposure level or the probability that any measurement exceeds a limit. Parametric methods used to determine acceptable levels of exposure, are often based on a two parameter lognormal distribution. The mean exposure level, an upper percentile, and the exceedance fraction are used to characterize exposure levels, and confidence limits are used to describe the uncertainty in these estimates. Statistical methods for random samples (without non-detects) from the lognormal distribution are well known for each of these situations. In this report, methods for estimating these quantities based on the maximum likelihood ...

International Nuclear Information System (INIS)

We calculated the energies of asymmetric nuclear matter at zero and finite temperatures with the cluster variational method. At zero temperature, the expectation value of the two-body Hamiltonian composed of the kinetic energies and the AV18 two-body forces is calculated with the Jastrow wave function in the two-body cluster approximation. The obtained two-body energy is in good agreement with the result with the Fermi Hypernetted Chain (FHNC) calculation by Akmal et al. The energy caused by the UIX three-body forces is treated somewhat phenomenologically so that the total energy reproduces the empirical saturation point. Furthermore, the parameters included in the three-body energy are readjusted so that the Thomas-Fermi (TF) calculations with use of the obtained energy of nuclear matter reproduce the gross feature of the experimental data on atomic nuclei. The nuclear species in the neutron star crust obtained by the TF calculation are reasonable. The free ...

International Nuclear Information System (INIS)

Mott-Schottky (M-S) analysis is an effective approach to investigate the electronic property of passive films of metals, and it is well suitable for the passive film with single space charge capacitance. But there is no proper method to analyze the Csc-2 vs. Vm plots of passive films with several space charge capacitances in series connection, such as bipolar passive films. In this paper, the relationship between the space charge capacitance of the bipolar passive film and the applied potential was deduced and the features of corresponding plots were given out simultaneously. Accordingly, a non-linear fitting method was presented to analyze the Csc-2 vs. Vm plots of bipolar passive films. Then the method was used to study the semiconductor characteristics of bipolar passive films formed on the surface of Nickel base alloy after being corroded in the environments with high temperatures and high partial ...

Energy Technology Data Exchange (ETDEWEB)

A probability-based approach is presented as the integration of probabilistic methods and deterministic modelling based on the finite element method. An existing finite element software package was linked to an existing probabilistic package to analyse the complex mechanics that occur during the transient non-linear analysis of impact problems. This methodology is applied to a pipe whip analysis of a group-distribution-header, which results from a guillotine break, and subsequent impact with the adjacent building wall; this is a postulated accident for the Ignalina Nuclear Power Plant RBMK-1500 reactors. The uncertainties of material properties, component geometry data and loads were taken into consideration. The probabilities of failure of the impacted header and of the header support-wall were estimated given uncertainties in material properties, geometrical parameters and loading. The software ProFES was used for the ...

Energy Technology Data Exchange (ETDEWEB)

This doctoral thesis addresses some problems in the analysis of spatial and spatial-temporal data and discusses prediction, prediction errors and identification of emission sources. European sulphur data are used as illustration. In an investigation of a spatial-temporal decomposition model for improving estimates of spatial interpolation (prediction) errors from monitoring data, the estimates were improved compared to estimates obtained by the method known as Kriging (an extension of the Wiener-Kolmogorov theory from time series to spatial processes), although the interpolated values were quite similar. A study of a random process model with an unknown, slowly varying trend and a correlated residual process is performed, using both trend estimation (smoothing) and prediction. Local polynomial methods are extended to continuous random processes. A new approach to non-parametric smoothing and to non-parametric Kriging is ...

International Nuclear Information System (INIS)

As part of the Nondestructive Evaluation Reliability Program sponsored by the US Nuclear Regulatory Commission, the Pacific Northwest Laboratory is developing a method that uses risk-based approaches to establish in-service inspection plans for nuclear power plant components. This method uses probabilistic risk assessment (PRA) results and Failure Modes and Effects Analysis (FEMA) techniques to identify and prioritize the most risk-important systems and components for inspection. The Surry Nuclear Power Station Unit 1 was selected for pilot applications of this method. The specific systems addressed in this report are the reactor pressure vessel, the reactor coolant, the low-pressure injection, and the auxiliary feedwater. The results provide a risk-based ranking of components within these systems and relate the target risk to target failure probability values for individual components. These results ...

International Nuclear Information System (INIS)

Peculiarities of Kurchatov Institute WWR-2 and TR research reactors spent fuel treating and transportation for radiochemical processing are stated. Spent fuels were performed as fuel assemblies of different forms and containing similar fuel elements: EhK-10 with 10% enrichment UO2-Mg fuel kernels or S-36 with 36% enrichment U-Al alloys. Spent fuel storage conditions are described. Features of developed procedures for identification of fuel assemblies by type of fuel elements are given. Transport package TUK-19 for loading and transportation of spent fuel for processing was chosen. Details of spent fuel loading in TUK-19 that is conducted by personnel under protective sheet of water in special reclaim volume are described

CERN Document Server

We consider various modifications of the Weyl-Moyal star-product, in order to obtain a finite range of nonlocality. The basic requirements are to preserve the commutation relations of the coordinates as well as the associativity of the new product. We show that a modification of the differential representation of the Weyl-Moyal star-product by an exponential function of derivatives will not lead to a finite range of nonlocality. We also modify the integral kernel of the star-product introducing a Gaussian damping, but find a nonassociative product which remains infinitely nonlocal. We are therefore led to propose that the Weyl-Moyal product should be modified by a cutoff like function, in order to remove the infinite nonlocality of the product. We provide such a product, but it appears that one has to abandon the possibility of analytic calculation with the new product.

British Library Electronic Table of Contents (United Kingdom)

Orthogonal frequency division multiplexing (OFDM) can fully use the frequency band and transmit data at high speeds. The ADSP-TS101 is a high performance digital signal processor (DSP) with good properties that include parallel processing and a high speed. Aimed at the real-time processing requirement of the OFDM algorithm, an underwater acoustic communication system with real-time processing capability is carried out. The system is mainly composed of multiple ADSP-TS101s, a multi-channel synchronous sample module and a field programmable gate array (FPGA) chip. The multiprocessor structure is made up of a cluster/data flow associated multiprocessing parallel processing structure as the operation kernel, and a multi-channel synchronous sample module is designed to realize no phase warp amo...

British Library Electronic Table of Contents (United Kingdom)

BACKGROUND: High levels of g-aminobutyric acid (GABA) accumulate in plant tissues under various stresses. GABA accumulation is also influenced by cultivar. This aim of this study was to select the most promising cultivar of fava bean for GABA accumulation and to optimise the culture conditions for GABA production in germinated fava beans by response surface methodology based on central composite design (CCD). RESULTS: GABA content and glutamate decarboxylase activity in germinated seeds of cultivar S2 were significantly higher than those in other cultivars (P < 0.05). A significant negative correlation (r = -0.765, P < 0.05) between germination percentage and 1000-kernel weight was observed. There was a linear relationship between GABA content and sprout length (R2 = 0.816). The regression...

CERN Document Server

In this paper we deal with a new class of Clifford algebra valued automorphic forms on arithmetic subgroups of the Ahlfors-Vahlen group. The forms that we consider are in the kernel of the operator $D \\Delta^{k/2}$ for some even $k \\in {\\mathbb{Z}}$. They will be called $k$-holomorphic Cliffordian automorphic forms. $k$-holomorphic Cliffordian functions are well equipped with many function theoretical tools. Furthermore, the real component functions have also the property that they are solutions to the homogeneous and inhomogeneous Weinstein equation. This function class includes the set of $k$-hypermonogenic functions as a special subset. While we have not been able so far to propose a construction for non-vanishing $k$-hypermonogenic cusp forms for $k \

International Nuclear Information System (INIS)

The Savannah River Site (SRS) is a 310-square-mile United States Department of Energy nuclear facility located along the Savannah River near Aiken, South Carolina. During operations, which started in 1951, hazardous substances (chemicals and radionuclides) were released to the environment. The releases occurred as a result of inadvertent spills and waste disposal in unlined pits and basins which was common practice before environmental regulations existed. The hazardous substances have migrated to the vadose zone and groundwater in many areas of the SRS, resulting in 515 waste units that are required by environmental regulations, to undergo characterization and, if needed, remediation. In the initial years of the SRS environmental cleanup program (early 1990's), the focus was to use common technologies (such as pump and treat, air stripping, excavation and removal) that actively and tangibly removed contamination. Exclusive use of these technologies required continued and significant ...

Energy Technology Data Exchange (ETDEWEB)

This work covers three distinct aspects of deformation and fracture during indentations. In particular, we develop an approach to verification of nanoindentation induced film fracture in hard film/soft substrate systems; we examine the ability to perform these experiments in harsh environments; we investigate the methods by which the resulting deformation from indentation can be quantified and correlated to computational simulations, and we examine the onset of plasticity during indentation testing. First, nanoindentation was utilized to induce fracture of brittle thin oxide films on compliant substrates. During the indentation, a load is applied and the penetration depth is continuously measured. A sudden discontinuity, indicative of film fracture, was observed upon the loading portion of the load-depth curve. The mechanical properties of thermally grown oxide films on various substrates were calculated using two different numerical ...

Energy Technology Data Exchange (ETDEWEB)

The calibration of cylindrical detectors using different types of radioactive sources is a matter of routine. The most accurate method, that of experiment, is limited by several factors when the energy interval is broad, requiring a relatively large number of primary standards, implying considerable investment of money and time. Several other techniques can be used instead, including Monte Carlo simulations and semi-empirical methods. Calculations based on the first technique require good definition of the geometry and materials, including the dead layer and window thickness together with an accurate set of cross-sections. The second technique requires two different types of experimental input, the first being from use of sources emitting cascade {gamma} rays and the second from use of sources emitting isolated {gamma} rays in order to cover the wide energy range and provide coincidence-summing corrections, respectively. Here, we introduce a ...

Energy Technology Data Exchange (ETDEWEB)

In the future, the demand for energy is predicted to grow and more countries plan to utilize nuclear energy as their source of electric energy. This gives rise to many important issues connected to nuclear energy, such as finding methods that can verify that the spent nuclear fuel has been handled safely and used in ordinary power producing cycles as stated by the operators. Gamma ray spectroscopy is one method used for identification and verification of spent nuclear fuel. In the specific gamma ray spectroscopy method called gamma scanning the gamma radiation from the fission products Cs-137, Cs-134 and Eu-154 are measured in a spent fuel assembly. From the results, conclusions can be drawn about the fuels characteristics. This degree project examines the possibilities of using alternative measuring approaches when using the gamma scanning method. The focus is on examining how to ...

International Nuclear Information System (INIS)

Research highlights: ? Mathematical model represents a power system which consists of synchronous machine connected to infinite bus through transmission line. ? Power system stabilizer was designed based on optimal pole shifting controller. ? The system performances was tested through load disturbances at different operating conditions. ? The system performance with the proposed optimal pole shifting controller is compared with the conventional pole placement controller. ? The digital simulation results indicated that the proposed controller has a superior performance. -- Abstract: Power system stabilizer based on optimal pole shifting is proposed. An approach for shifting the real parts of the open-loop poles to any desired positions while preserving the imaginary parts is presented. In each step of this approach, it is required to solve a first-order or a second-order linear matrix Lyapunov equation for shifting one real pole or two complex ...

Science.gov (United States)

Not Available