KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The concentration of some organic acids in the atmosphere was determined using a wet effluent diffusion denuder-aerosol collector coupled with Ion Chromatography. Three organic acids and four inorganic anions were identified and quantified in the air sample, taken from the backyard of PSI. (author)

UK PubMed Central (United Kingdom)

Norway spruce (Picea abies L. Karst) produces an oleoresin characterized by a diverse array of terpenoids, monoterpenoids, sesquiterpenoids, and diterpene resin acids that can protect...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Purpose Evaluation of the all-trans retinoic acid (t-RA) effects on in vitro maturation (IVM) and in vitro fertilization (IVF) of immature mouse oocytes in the presence and absence of granulosa cell monolayer. Methods Denuded oocytes isolated from mice ovaries and matured in IVM medium alone (Control I), IVM medium in the presence of granulosa cells (Control II), IVM medium with t-RA (Experimental I) and IVM medium simultaneously with t-RA and granulosa cells (Experimental II). After 24?h, matured oocytes were fertilized in T6 medium and their development was followed until the blastocyst stage. Metaphase II oocytes ploidy were evaluated by chromosome counting. Results The t-RA group compared to the control groups showed no obvious abnormalities. Additionally maturation and embryo developm...

British Library Electronic Table of Contents (United Kingdom)

Human activities in the karst Ozark Plateaus can impact water quality of springs where surface water is rapidly transferred to subsurface conduits. Bennett Spring, in southern Missouri, is the fourth largest spring in the state and supports local tourism activities. Questions regarding poorly functioning on-site wastewater systems (OWS) have raised concerns over the long-term water quality of the spring. This study reports the results of a surface water quality monitoring program in the recharge area where monthly samples were collected at base flow to identify potential pollution sources to the spring. Base flow hydrology of the recharge area was highly variable over the study period, which was drier than normal, causing an incomplete sampling record due to no flow conditions at some site...

Science.gov (United States)

Sulfur dioxide emissions from an iron ore sintering plant have severely damaged vegetation up to 16 km northeast of the source. Concentric zones of increasing vegetation loss have formed around the point of maximum ground level concentration of the gas. Species diversity, sulfur and heavy metal concentrations in vegetation and soil amount to SO/sub 2/ injury were measured along a transect through the injury zones. Surrounding a central denuded area were zones dominated respectively by tussock-forming hair grass (Deschampsia flexuosa); low-growing shrubs and trailers (Sambucus pubens, Polygonum cilinode); higher-growing shrubs and suckering Populus tremuloides and Betula papyrifera) stunted forest tree species (Populus, Betula, Picea glauca, Abies Balsamea), and finally, normal boreal forest flora. Although SO/sub 2/ injury is continuing in this area, these zones now appear to be maintained primarily by severe erosion and destruction of suitable habitats for ...

Energy Technology Data Exchange (ETDEWEB)

Silicon on insulator (SOI) structures are promising candidates for the fabrication of VLSI circuits with very high packing densities. The preparation of such structures can now be achieved by high dose implantation of reactive ion species such as oxygen to produce buried layers of SiO/sub 2/ in silicon. In this paper we report experiments to depth profile these layered structures by SIMS. SOI samples have been prepared by implanting (100) silicon wafers with 400 keV molecular oxygen ions at a dose of 1.8x10/sup 18/ O/sup +/ cm/sup -2/. During the implantation the wafers were maintained at temperatures between 325 and 600/sup 0/C, using beam heating, which achieved in situ-annealing and ensured that the top silicon layer remained single crystal. Analysis was carried out on an Atomika DIDA-II spectrometer using 10 keV Ar/sup +/ ions with a low current density of less than 1 mA cm/sup -2/. During analysis negative secondary ions were monitored which provided a high detection sensitivity ...

Energy Technology Data Exchange (ETDEWEB)

As part of a five-year-lasting open-top-chamber experiment at the `Edelmannshof` site (Welzheimer Wald) we analyzed Norway spruce trees (Picea abies (L.) Karst.) with regard to carbohydrate and energy (ATP/ADP ratio) metabolism. End products, intermediates, and a regulator of carbon allocation (starch, sucrose, hexoses, fructose-2,6-bisphosphate) as well as enzyme activities involved in sucrose metabolism (sucrose-P synthase, sucrose synthase, acid invertase) were determined in needle and trunk samples of the different treatments (charcoal-filtered, unfiltered, ambient air). Changes of these parameters were documented annually and with regard to needle development (up to 2 years after bud break), and diurnally during an ozone period in midsummer. Samples from trees grown in an unfiltered atmosphere showed relatively high sucrose and hexose contents of the needles. The capacities of sucrose-P synthase (increased; sucrose synthesis) and acid invertase (decreased; ...

Energy Technology Data Exchange (ETDEWEB)

Personnel from Martin Marietta Energy Systems, Inc. (Energy Systems) manage a closed hazardous waste disposal unit the Chestnut Ridge Security Pits (CRSP), located on the crest of Chestnut Ridge near the Y-12 Plant, Oak Ridge, Tennessee. To investigate the discharge of groundwater from CRSP to springs and streams located along the flanks and base of Chestnut Ridge, an initial dye-tracer study was conducted during 1990. A hydraulic connection was inferred to exist between the injection well (GW-178) on Chestnut Ridge and several sites to the east-northeast, east, and southeast of CRSP. A second dye-tracer study was conducted in 1992 to verify the results of the initial test and identify additional discharge points that are active during wet-weather conditions. No definitive evidence for the presence of dye was identified at any of the 35 locations monitored during the second dye study. Although interpretations of the initial dye test suggest a hydraulic connection with several sites and ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

A remarkably simple argument successfully accounts for the rate of star formation in different galaxies. The snag is that the timescale is uncomfortably short.

UK PubMed Central (United Kingdom)

A new analysis is presented which links real volume fractions, relaxation rates, and intracompartmental exchange rates directly with apparent volume fractions and relaxation rates obtained from biexponential...Full Text Available

UK PubMed Central (United Kingdom)

1. Rates and rate coefficients of glucose utilization and replacement were determined with [5-3H]- and [U-14C]-glucose in rats starved for 24h, either conscious or under halothane anaesthesia, in a...Full Text Available

Science.gov (United States)

... rate on the tensile properties of SA-106 carbon steel pipe, in support of analysis and experimental modeling of postulated pipe whip in nuclear ...

Science.gov (United States)

... Joint Staff and other US Military (ie, Army, Navy, Air ... HEART RATE, AND BODY TEMPERATURE DURING WORK IN MAN, DOG, AND SWINE. ...

Science.gov (United States)

... sample. Hosoitalization Data Hospital admission rates across Navy ships :.n 1985 and 1975 are presented in Table 17. ...

Science.gov (United States)

Indicated inertial navigation error and required update frequency. phasing, and times). Docking Phase. Range; range rate. Clock angle; clock angle rate ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication

Science.gov (United States)

... breakthrough in Normandy), "Goodwood-Atlantic," and "Totalize" (British-Canadian operations) in the same campaign. It ...

KoreaScience (Korea)

Full Text Available

Medline Plus

... diagnosed. A complete blood count (CBC), urinalysis, blood chemistries, and erythrocyte sedimentation rate (ESR) tests can provide ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Dyslipidemia

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... crystals and polycrystals. Nevertheless, explosive forming, magnetic forming, etc., are all high-strain-rate processes that ...

Science.gov (United States)

Limestone dissolution rate was measured by a pH-stat method with CO(2) sparging and dissolved sulfite. The dissolution rate of limestone under these conditions was found to be controlled by mass transfer and surface kinetics. As can be seen from the results, in the presence of sulfite, limestone dissolution rate increases with increasing stirring speed, reaction temperature and CO(2) partial pressure. The crystallinity of limestone has a great impact on the dissolution rate: The lower the value of the crystallinity of limestone is, the higher the dissolution rate is. The presence of sulfite promotes the dissolution rate when pH value is below 5.5 but inhibits it when pH value is above 5.5. PMID:19359093

Energy Technology Data Exchange (ETDEWEB)

Fission rate assessments are being made in FFTF to provide input for determination of power distribution, peak power, total power, fuel burnup distribution, conversion ration and neutron spectral information by the multiple foil reaction rate method. A goal of the initial FFTF Characterization Program is to measure isotopic fission rates to an accuracy of 2 to 5% throughout FFTF by radiometric techniques. To achieve this goal, measurements were made in the FFTF In-Reactor Thimble to reduce the uncertainties of key parameters needed for radiometric fission rate mapping of the FFTF core.

International Nuclear Information System (INIS)

In this study based on the mass transfer theory, experiments for the evaporation rates depending on various conditions were carried out through the operation of the existing Natural Evaporation Facility in KAERI. Evaporation media were made of the cotton and polyester. Air circulation in the facility was forced by exhausting fans. The evaporation rate and the decontamination factor were calculated by the result of experiment. The evaporation rate increased as the flow rate of air supply, the feed rate of liquid waste, and the temperature of supplied air increased. As for the humility of supplied air, the evaporation rate was getting higher as the humidity was getting lower. As the result of this study, operation conditions of the Natural Evaporation Facility are optimized as follows; The air temperature above 8C .deg., the air humidity below 70%, the air flow ...

International Nuclear Information System (INIS)

Activation energy values for high temperature deformation of a beta -titanium alloy Ti-10V were determined from the flow stress strain rate data taken from the second increasing strain rate cycles, in order to find the rate controlling mechanism. Although the data obtained from first increasing strain rate cycles are considered most appropriated by the author in a previous study due to obvious reasons, the values obtained in present work are again indicative of lattice self diffusion in beta -phase as the rate controlling mechanism for this alloy and nevertheless suggest that two different activation energy values for a deformation process could be possible in a given temperature range, depending upon the data. (author)

UK PubMed Central (United Kingdom)

BackgroundExisting studies concerning the health care use of homeless people describe higher utilisation rates for hospital-based care and emergency care, and lower rates for primary...Full Text Available

UK PubMed Central (United Kingdom)

Sustained metabolic rates (SusMR) are time-averaged metabolic rates that are measured in free-ranging animals maintaining constant body mass over periods long enough that metabolism is fueled by food...Full Text Available

UK PubMed Central (United Kingdom)

We have measured the forward and reverse rates of the allosteric transition of hemoglobin A with three CO molecules bound by using modulated excitation coupled with fluorescence quenching of the DPG...Full Text Available

Science.gov (United States)

Results are reported from studies of the diffusion rate of xenon through frog abdominal skin and toad urinary bladders, typical epithelial membranes. It was concluded that intracellular water serves as the principal barrier for xenon passage through epithelial tissue.

UK PubMed Central (United Kingdom)

BackgroundControversy exists about how to effectively measure patient reported outcomes in IBS clinical trials. Pain numeric rating scales (NRS) are widely used in...Full Text Available

UK PubMed Central (United Kingdom)

Basal or standard metabolic rate (SMR) has been found to exhibit substantial intraspecific variation in a range of taxa, but the consequences of this variation are little understood. Here we explore...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In the region of annular liquid film-mist flow, the behavior of the droplets formed from the liquid film and the rate of formation are the subjects to be clarified in connection with the forecast of dry-out point, which becomes a problem in the region of high dryness such as reactor cooling system and steam generators. Many researches have been performed on such problem in vertical tubes, but the characteristics in horizontal flow have not yet been sufficiently clarified. This series of research is to clarify various characteristics, such as the velocity of vapor phase, the flow rate distribution of droplets, the formation and adhesion of droplets and the structure of liquid film, in the region of liquid film-mist flow, where liquid film exists on the bottom of a horizontal rectangular channel, and vapor flow is accompanied by droplets. In this study, by the measurement of the flow rate distribution of droplets on ...

UK PubMed Central (United Kingdom)

From the gross conservation laws of thermodynamics in a convecting material we derive a bound on the ratio of the rate of production of mechanical or magnetic energy to the rate of internal radioactive...Full Text Available

International Nuclear Information System (INIS)

Hoogenstraaten's heating rate method has generally been considered as a reliable method for determining thermoluminescence trapping parameters of first order glow peaks. However, experience has shown that in some cases the deviation between the heating rate method and glow curve fitting method can be quite significant (considering only the linear part of the heating rate plot, of course). In this study it is shown that one of the main reasons for this deviation can be a systematic increase of a temperature lag between the measured and real temperature of the sample with increasing heating rate. It appears that this systematic increase of the temperature lag affects the method in the range of low heating rates (linear part of the heating rates plots) more than has been previously realised. The effect of the temperature lag on Hoogenstraaten's heating ...

Energy Technology Data Exchange (ETDEWEB)

To evaluate the effectiveness of percutaneous transluminal angioplasty(PTA) and to determine the factors affecting the long-term patency rate in the management of insufficient hemodialytic arteriovenous fistula(AVF). Forty-nine cases of insufficient hemodialytic AVF were treated in 44 patients(native AVF:20, graft AVF:29, M:17, F:27, Age:22-70 years). In 28 thrombus patients, thrombolysis was performed with urokinase, and was followed by PTA. The initial success rate and complications of PTA were evaluated. According to the site and length of the stenosis, type and age of the AVF, the presence or abscence of thrombus, a history of diabetic mellitus, the patient's age, and the duration of renal failure, patency rates were compared within each subgroup using the Kaplan-Meier logrank test. The initial success rate of PTA for insufficient hemodialytic AVF was 88%(43/49), the patency ...

UK PubMed Central (United Kingdom)

Cimetidine 1 g daily is often continued for a fixed period beyond the time of healing of duodenal ulcer on the assumption that it might reduce the subsequent relapse rate. To test this, 194 patients...Full Text Available

UK PubMed Central (United Kingdom)

Energetically costly behaviours, such as flight, push physiological systems to their limits requiring metabolic rates (MR) that are highly elevated above the resting MR (RMR). Both RMR and MR during...Full Text Available

UK PubMed Central (United Kingdom)

For the evaluation of the kidney impairment, serum creatinine concentrations or glomerular filtration rates are mainly used, and the conditions of solitary or transplanted kidney and chronic dialysis...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This book contains over 20 selections. Some of the titles are: Continuum damage mechanics studies on the dynamic fracture of concrete; Dynamic compressive strength of cementitious materials; Rate-sensitivity of mode I and mode II fracture concrete; and An impact damage model of concrete.

Science.gov (United States)

The fuel cell model also provides the cryogenic use rates to the cryogenics model. The primary subroutines are FUELIV and. FUCLTM. ...

International Nuclear Information System (INIS)

When decontaminated with continuously replenished CAN-DECON reagent in a once-through system, carbon steel contaminated with "6"0Co during exposure to reducing coolant in stainless steel loops loses up to 90 percent of its radioactivity in the first few minutes. Afterwards, the rate of removal falls to much lower values which persist for many hours to the end of the experiment. The effects of flow rate, temperature and reagent concentration on the initial rates of decontamination indicate that mass transfer in the liquid is an important factor in the decontamination. The decontamination factor is influenced by the initial rate.

Energy Technology Data Exchange (ETDEWEB)

Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)

KoreaScience (Korea)

Full Text Available

CERN Document Server

We briefly report on zero-temperature photoassociation of a Bose-Einstein condensate, focusing on the many-body rate limit for atom-molecule conversion. An upgraded model that explicitly includes spontaneous radiative decay leads to an unanticipated shift in the position of the photoassociation resonance, which affects whether the rate (constant) maximizes or saturates, as well as the limiting value itself. A simple analytical model agrees with numerical experiments, but only for high density. Finally, an explicit comparison with the two-body unitary limit, set by the size of the condensate, finds that the many-body rate limit is generally more strict.

Science.gov (United States)

The ionization, excitation, and radiative recombination rates for highly stripped ions are cal- culated with Maxwellian and non-Maxwellian electron distribution functions of the type Cmexp(-vm/wm) (2<=m<=5) as encountered in laser-heated plasmas and certain types of turbulent plasmas. The direct-radiative-recombination rates are found to decrease by at most 30% as m is increased from 2 to 5. On the other hand, the ionization and excitation rates are found to be strongly reduced if the transition energy ? exceeds twice the local temperature kBTe. The effect of this on the distribution of energy levels and degrees of ionization in laser-produced plasmas could be important.

Energy Technology Data Exchange (ETDEWEB)

Measurements of the expansion rate of pure-electron plasmas have been performed on the Electron Diffusion Gauge (EDG) device at background helium gas pressures in the 5 x 10(superscript -8) Torr to 1 x 10(superscript -5) Torr range, where plasma expansion due to electron-neutral collisions dominates over plasma expansion due to trap asymmetries. It is found that the expansion rate, defined as the time rate of change of the particles' mean-square radius, scales approximately linearly with pressure and inversely as the square of the magnetic field strength in this regime, in agreement with classical predictions.

International Nuclear Information System (INIS)

... Sciences, Research Center for Radiation Protection, Chiba (Japan) Hafez,

UK PubMed Central (United Kingdom)

To obtain the low birth weight (LBW) rate, the very low birth weight (VLBW) rate, and gestational age (GA)-specific birth weight distribution based on a large population in Korea, we collected and analyzed...Full Text Available

International Nuclear Information System (INIS)

The total radiation rate, angular distribution of the emitted energy and photon correlations of the cooperative spontaneous radiation from two atoms with different resonance frequencies and spontaneous decay rates are calculated. Contrary to the case of two identical atoms oscillations appear in the total radiation rate and the spatial distribution of the total number of emitted photons differs from the single-atom radiation pattern. The effect of the dipole-dipole near-field interaction on the time evolution of the atomic system is discussed. (author).

British Library Electronic Table of Contents (United Kingdom)

Intermittent sun exposure and sunburn are strong predictors of cutaneous malignant melanoma (CMM). On the other hand, melanomas may arise also in non-sun-exposed areas such as the vulva. However, little is known about a possible relationship between sun exposure and vulvar melanoma. Temporal and latitudinal dependencies of the incidence rates of vulvar melanoma were studied in comparison with those of CMM among Caucasians in Sweden, East Germany, USA and Victoria (Australia). The ratios of vulvar melanoma incidence rates to those of CMM tend to decrease with increasing CMM rates. The incidence rates of CMM have increased with time until recently, while those of vulvar melanoma have either decreased or remain constant. In USA vulvar melanoma incidence rates seem to increase from south to no...

Energy Technology Data Exchange (ETDEWEB)

The effects of the heating rate from 0.6 up to 50{sup o}C.s{sup -1} on the thermoluminescence of {alpha}-Al{sub 2}O{sub 3}:C are very intensive. The material rapidly loses its high sensitivity as the heating rate increases. The peak shape characteristics, peak maximum and full width at half maximum agree only qualitatively with those theoretically predicted. The trapping parameters calculated by the curve fitting method, the peak shape method, the variable heating rate method and the initial rise method, were found to decrease as the heating rate increases. The validity of the results are discussed in the framework of the kinetic models. (author).

British Library Electronic Table of Contents (United Kingdom)

Summary 1.-The metabolic theory of ecology (MTE) predicts that, after correcting for body mass variation among organisms, the rates of most biological processes will vary as a universal function of temperature. However, empirical support for -universal temperature dependence- (UTD) is currently equivocal and based on studies of a limited number of traits. 2.-In many ectothermic animals, the rate at which females produce mature eggs is temperature dependent and may be an important factor in determining the costs of reproduction. 3.-We tested whether the rate of egg maturation in marine turtles varies with environmental temperature as predicted by MTE, using the time separating successive clutches of individual females to estimate the rate at which eggs are formed. We also assessed the pheno...

International Nuclear Information System (INIS)

Turbulent premixed methane-air combustion in a cylindrical chamber is numerically simulated considering radiation effect. Reaction rates are considered as minimum rates between Arrhenius rates and eddy break up rates. A five step reduced mechanism is used. Turbulent modeling is done via standard k-? model imposed by empirical inlet boundary conditions. Source terms of energy equation consist of reaction rates and radiation effects. The discrete ordinate method (DOM) is employed to solve the radiative transfer equation (RTE) and the weighted sum of gray gas model (WSGGM) is imposed to consider radiation effect of non-gray gases. The results indicate that in the case of turbulent combusting flows, the effect of radiation of gases can affect the temperature and species concentrations. The numerical results obtained considering radiation effect are closer to the experimental data than ...

British Library Electronic Table of Contents (United Kingdom)

Introduction: The QT interval of the electrocardiogram (ECG) reflects the duration of ventricular depolarization and repolarization. A drug-induced prolongation of ventricular repolarization, and thereby QT prolongation, is recognized to be a marker for an enhanced risk for ventricular arrhythmia. The assessment of a drug's effect on the QT interval has therefore become routine within pharmaceutical research and development. However, the heart rate has a major influence on the QT interval; the QT interval shortens as heart rate increases such that one needs to account for such heart rate-dependent changes when evaluating possible drug-induced effects on the QT interval. The relationship between the QT interval and heart rate can be modeled mathematically and using this function a so-called...

International Nuclear Information System (INIS)

An Fe-15Cr-20Ni ternary model alloy and a Type 316 stainless steel were irradiated by dual-ions at 1 to 50 appm of He/dpa ratios, to investigate the helium effects on microstructural development in austenitic alloys under irradiation. Quantitative analysis on resultant microstructures revealed that the Frank loop nucleation rate and the network dislocation density positively correlate and Frank loop growth rate negatively correlate with the He/dpa ratio, while the cavity growth rate has its peak at an intermediate helium injection rate. Although He/dpa dependence of various microstructural features were similar for the model alloy and the 316SS, the rates of their development and the mechanism which had assisted cavity growth were significantly different in these two materials. (orig.).

International Nuclear Information System (INIS)

Purpose: To provide a feedwater control device capable of minimizing the adverse response of steam drum level at low power. Consitution: In order to perform feedwater control at low power by the substantial control of three factors, that is, main steam flow rate, feedwater flow rate and steam drum level, the main steam flow rate is determined from the reactor output and feedwater rate is determined from the changes in the feedwater temperature due to the mixing of waters in the reactor clean up system and feedwater. If a difference is resulted between these flow rates, a starting feedwater regulator is controlled instantly to eliminate the difference. The water level in the steam drum is used for amending the difference from the final set value of the drum water level, by which the adverse response of the steam drum level can be minimized. (Seki, T.).

Energy Technology Data Exchange (ETDEWEB)

Measurements of local mass fluxes of liquid, local number fluxes of the drop and local drop size distributions at various locations in the test column were made for wide ranges of liquid flow rates and gas flow rates. An empirical correlation for the volume mean diameter of the drop at the nozzle exit was proposed. Measurements of the rates of absorption of carbon dioxide from carbon dioxide-air mixtures with water sprays (physical absorption) and aqueous sodium hydroxide sprays (chemical absorption) were made for wide range so fluid flow rates, feed gas concentrations, and initial alkali concentrations. The observed dimensionless rates of absorption were compared with the theoretical values by assuming penetration model with second-order irreversible reaction. 11 refs., 7 figs.

Energy Technology Data Exchange (ETDEWEB)

A Vacuum Circuit Breaker demonstrated its ability to interrupt short circuits with faster than normal rates of rise of Transient Recovery Voltage (TRV) at levels greater than those produced by most transformer secondary faults. Two recent exploratory test programs evaluated the interrupting ability of a 15kV Vacuum Circuit Breaker containing interrupters of the rotating arc type with contacts made from a Chromium-Copper powder metal mixture. The interrupting conditions covered a wide range of currents from 10% to 130% of the 28kA rated short circuit current of the tested circuit breaker and a wide range of TRV rates of rise, including the relatively slow rate of rise, normally used in testing and found in most indoor circuit breaker applications; two faster rates of rise equaling and exceeding those found in a known power plant transformer secondary protection application; and the ...

International Nuclear Information System (INIS)

Object: To control the average liquid level of each steam generator at a constant level irrespective of the flow rate of sodium thereby to decrease change in the retained amount of sodium and at the same time to improve the load response characteristic. Construction: A method for decreasing to as large an extent as possible a change in the amount of sodium retained in a steam generator due to change in the flow rate, which comprises the steps of detecting the main recirculating flow rate of liquid sodium by the use of a sodium flow rate detector, amplifying the detected flow rate signal depending upon the ratio between the flow rates respectively in a super-heater and a re-heater (distribution ratio), delivering the amplified signal to a function generator which generates a liquid level setting signal for maintaining the respective average liquid levels of the ...

Energy Technology Data Exchange (ETDEWEB)

The kinetics of calcium sulfate crystal growth is of importance in various fields, such as geochemistry, desalination technology, petroleum industry, and water and wastewater treatment. The seeded crystal growth rate of calcium sulfate dihydrate was measured as a function of supersaturation in NaCl electrolyte solutions from 0 to 6 m at temperatures of 25, 50, 70, and 90 C. The growth followed a second-order parabolic rate law with activation energies greater than 53 kJ/mol which suggested the surface reaction as the rate-limiting step. It was observed that the rate constant and the activation energy are solution composition dependent. The rate constant increases with NaCl concentration up to 3 molal and then begins to fall slightly. The activation energy dropped from 61 kJ/mol in the pure Ca-SO[sub 4]H[sub 2]O system to 53 kJ/mol in 3.0 m NaCl solutions. The electrolyte effect was ...

Energy Technology Data Exchange (ETDEWEB)

Quantitative bone scintigraphy was performed in 24 patients with prostatic carcinoma before orchiectomy and up to one to four years after operation. The gamma camera count rate was recorded over the lower thoracic and all lumbar vertebrae 4 h after injection of [sup 99m]Tc-MDP. Twelve patients has normal bone scintigrams throughout the study. They showed from two years after operation a slight increase in count rate values compared with the preoperative values, probability due to hormonal changes after orchiectomy and to age-related alterations in skeletal metabolism. Twelve patients had abnormal bone scintigrams. They showed as a response to treatment the flare phenomenon with an increase in count rate over the abnormal vertebrae when measured two weeks after operation followed by a decrease after two months. The lowest count rate values were obtained between six months and one year after operation. ...

Energy Technology Data Exchange (ETDEWEB)

A thermal analyzer-differential scanning calorimeter-mass spectrometer (TG-DSC-MS) was used to study oxygen carriers (OC) for their potential use for the application of chemical looping combustion (CLC) to solid fuels. Reaction rates, changes in reaction rates with repeated oxidation-reductions, exothermic heats during oxidation, and the effect of changing reduction gas compositions were studied. Oxidation rates were greater than reduction rates and reaction rates were reproducible through multiple oxidation-reduction cycles except where agglomeration occurred with powders. Iron oxide (Fe{sub 2}O{sub 3} powder) and iron-based catalysts were found suitable for CLC of solid fuels having rapid reduction rates which increased with higher reducing gas concentrations. Fe{sub 2}O{sub 3} powder was used to oxidize a high carbon coal char in an inert gas removing 88% of ...

Energy Technology Data Exchange (ETDEWEB)

The study to get some fundamental materials was carried out, aiming at the recovery of valuable components from red mud produced in the bauxite processing. Acid leaching of red mud was used to clarify the effect of leaching time, leaching temperature and acid concentration on the recovery. The used acids were hydrochloric acid, sulfuric acid and nitric acid of which concentrations were 1.45, 1.8 and 1.2mol-l; the temperature was 25, 40 and 60 centigrade; and the time was 1, 2, 4 and 8 hours. Al in red mud was leached by all acids, became the equilibrium after 10 minutes, and was independent og the temperature and the leaching rate was about 70%. When the acid concentration was raised to two time for sulfuric acid and hydrochloric acid, the leaching rate increased by 15%. Si showed the same tendency as Al and the leaching rate was about 65%, but the decrease of 15% was confirmed by raising the concentration of sulfuric acid ...

Science.gov (United States)

Preschool-age children hold negative attitudes toward overweight peers (i.e., anti-fat attitudes), but little is known about individual differences in these attitudes. The current study investigated actual weight status and perceived body size in relation to preschool-age children's anti-fat attitudes. Sixty-nine 4-6 year-olds (61% girls) were individually interviewed about their body size perceptions using a figure rating scale and anti-fat attitudes using multiple methods (including an adjective rating scale and ratings of acceptability for different body shapes). Results suggested that children's perceived body size, not actual body size, was related to their attitudes about an overweight figure and the number of figures rated as acceptable. Children who perceived themselves as heavier held fewer anti-fat attitudes. Perceived and actual body size ratings were not related to ...

International Nuclear Information System (INIS)

Exposure control at the operating Nuclear Power Station is a major concern. TAPS Unit-4 is the first Pressurized Heavy Water Reactor of 540 MWe electrical capacity. This unit was made critical on March 6, 2005. In-depth review of radiation safety was done to identify the impact of design modification on dose rates at various locations and on the equipment's. Problems encountered in controlling the dose rates in 220 MWe electrical are eliminated by appropriate design modifications. Due to higher capacity of the unit there are design changes in major systems such as reactor core, primer heat transport system, moderator system, reactor regulation and protection systems. Reactor operations and maintenance activities during shut down contributes to exposure of the employees. Based on the experience gained in the operation of 220 MWe, design modifications incorporated in TAPS unit-4 and dose rate measurements carried out at 90 % ...

CERN Document Server

We estimate binary compact object merger detection rates for LIGO, including the binaries formed in ellipticals long ago. Specifically, we convolve hundreds of model realizations of elliptical- and spiral-galaxy population syntheses with a model for elliptical- and spiral-galaxy star formation history as a function of redshift. Our results favor local merger rate densities of 4\\times 10^{-3} {Mpc}^{-3}{Myr}^{-1} for binary black holes (BH), 3\\times 10^{-2} {Mpc}^{-3}{Myr}^{-1} for binary neutron stars (NS), and 10^{-2} {Mpc}^{-3}{Myr}^{-1} for BH-NS binaries. Mergers in elliptical galaxies are a significant fraction of our total estimate for BH-BH and BH-NS detection rates; NS-NS detection rates are dominated by the contribution from spiral galaxies. Using only models that reproduce current observations of Galactic NS-NS binaries, we find slightly higher rates for NS-NS and ...

Energy Technology Data Exchange (ETDEWEB)

This dissertation describes a measurement of the rate ofnuclear muon capture by the proton, performed by the MuCap Collaborationusing a new technique based on a time projection chamber operating inultraclean, deuterium-depleted hydrogen gas at room temperature and 1 MPapressure. The hydrogen target's low gas density of 1 percent compared toliquid hydrogen is key to avoiding uncertainties that arise from theformation of muonic molecules. The capture rate was obtained from thedifference between the mu- disappearance rate in hydrogen--as determinedfrom data collected in the experiment's first physics run in fall2004--and the world averagefor the mu+ decay rate. After combining theresults of my analysis with the results from another independent analysisof the 2004 data, the muon capture rate from the hyperfine singlet groundstate of the mu-p atom is found to be ...

International Nuclear Information System (INIS)

Experimental investigations of the turbulence characteristics of the air flow above the wave surface of the film in the horizontal rectangular channel in the 5-20 m/s velosity range of the air rate change (Reynolds number for the air 120O0-48000, 100-1000 for the film) are carried out. It is shown that intensities of turbulent pulsations of the rate increase with the growth of liquid flow rate in the film especially in the region of large squall waves. The experimental results on the pulsations are presented in the dimensionless form by a universal dependence. Distributions of tangentials of turbulent stresses above the film are obtained, turbulent stresses are compared with friction losses at the phase interface.

International Nuclear Information System (INIS)

The system which is performed the transportation and measurement of drum automatically to measure the surface dose-rate of radioactive waste drum and can inspect place of contaminated sources and precise dose-rate within a drum according to measuring many places equally at the same time has been developed. It is expected that the system be used to minimized radiation exposure of workers and manage the drum effectively according to established at the production facilities as well as the radioactive waste treatment facilities. (author). 7 refs., 9 tabs., 16 figs.

International Nuclear Information System (INIS)

Superplastic deformation behavior in an alpha + beta titanium alloy Ti-3A-4V has been investigated by using the method of cross head speed cycling in the temperature range 750-910 /sup 0/C. On the basis of flow stress-strain rate-strain rate sensitivity data, the alloy was found to be superplastic in the entire temperature range studied. Optimum superplasticity was observed in the strain-rate range 3 x 10/sup -5/ sec./sup -1/ to 6 x 10/sup -5/ and at the highest temperature of 910 deg. C. (author).

CERN Document Server

The intrinsic decay rate of orthopositronium formed in SiO/sub 2/ powder is measured using the direct 2 gamma correction method such that the time dependence of the pick-off annihilation rate is precisely determined. The decay rate of orthopositronium is found to be 7.0396+or-0.0012(stat.)+or-0.0011(sys.)/ mu s/sup -1/, which is consistent with our previous measurements with about twice the accuracy. Results agree well with the O( alpha /sup 2/) QED prediction, and also with a result reported very recently using nanoporous film.

Energy Technology Data Exchange (ETDEWEB)

To utilize ethanol from agricultural residue as a fuel in diesel engines, a dual-fuel engine was developed. The engine, which was equipped with a system to electrically control diesel and alcohol flow rates, met basic requirements of a tractor engine, including engine speed control and setting of the torque curve. However, engine knock due to alcohol was a significant drawback. A diesel injection pump with a timing and flow rate control system was adapted, and the effect of injection timing on combustion and performance was investigated. It was observed that the timing control was effective in reducing engine knock caused by rapid alcohol combustion. (author)

International Nuclear Information System (INIS)

Cr_2O_3 scales are found to form on Alloy 800 and a similar pure ternary alloy in air, and 1 and 50 atm. helium containing oxidizing impurities typical of those in an SGHTR. The strong temperature dependence and neglibible helium overpressure dependence indicate that gas transport through the scales is not rate controlling. Surface oxidation rates are therefore controlled by solid state diffusion and the low oxygen partial pressure dependence of the oxidation rate in Alloy 800 is ascribed to the presence of extrinsic defects in the Cr_3O_3 (due to doping by alloying elements) or to the presence of short circuit diffusion paths. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Optimum conditions for microstructural control in industrial hot working of cast and homogenized AZ31 magnesium alloys are evaluated by using a processing map. The recommended window for bulk metal working of this alloy is the domain in the temperature range 300-450 C and strain rate range 1-10 s{sup -1}, and the optimum processing parameters are 400 C and 10 s{sup -1}, where grain-boundary self diffusion is the rate-controlling mechanism. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Absolute fission rate measurements using modified National Bureau of Standards fission chambers were performed in the Fast Flux Test Facility at two core locations for isotopic deposits of {sup 232}Th, {sup 233}U, {sup 235}U, {sup 238}U, {sup 237}Np, {sup 239}Pu, {sup 240}Pu, and {sup 241}Pu. Monitor chamber results at a third location were analyzed to support other experiments involving passive dosimeter fission rate determinations.

Energy Technology Data Exchange (ETDEWEB)

Absorption and desorption rate data for the system CO/sub 2/-hot carbonate solutions are presented. The data are interpreted on the basis of a film-theory model developed following the procedure recently presented by Astarita and Savage. The agreement is very satisfactory. Values of the kinetic constant of the rate-determining step, previously known only up to a temperature of 40/sup 0/C, have been obtained up to 110/sup 0/C.

Scientific Electronic Library Online (English)

Abstract in english A simplified model for drying solids in the constant rate period in a batch fluidised bed was developed.It assumes the bed to be divided into dense and bubble phases with heat and mass transfer between the phases.The model predicts the constant-rate drying period, provided the fluid bed shape and material characteristics are known.The model is compared with experimental data reported in the literature covering a wide range of materials, gas flow rates, column diameters, m (more) aterial hold-ups, air temperatures and humidities.Model predictions compare satisfactorily with the experimental data.

British Library Electronic Table of Contents (United Kingdom)

Collaborative Filtering (CF) is a popular method for personalizing product recommendations for e-Commerce and customer relationship management (CRM). CF utilizes the explicit or implicit product evaluation ratings of customers to develop personalized recommendations. However, there has been no in-depth investigation of the parameters of CF in relation to the number of ratings on the part of an individual customer and the total number of ratings for an item. We empirically investigated the relationships between these two parameters and CF performance, using two publicly available data sets, EachMovie and MovieLens. We conducted three experiments. The first two investigated the relationship between a particular customer?s number of ratings and CF recommendation performance. The third experim...

Science.gov (United States)

... drugs, foods, environmental conditions, and behavioral disorders (1,8,10,17,18,24,29). In addition, we designed a self-rated ...

Science.gov (United States)

Manufacture of cadmium sulfide thin film solar cells

Science.gov (United States)

... 2. K. Dorenwendt, "Das verhalten kommerzieller Casium-Atomuhren und die Zeitskalen der PTBn, Proceedings of the 31st International Congress ...

UK PubMed Central (United Kingdom)

BackgroundUnderstanding the mechanisms that control rates of disease progression in humans and other species is an important area of research relevant to epidemiology and to translating...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Direct current motors are used in photovoltaic systems. Important characteristics of electric motors are the starting to rated current and the torque ratios. These ratios are dictated by the size of the solar cell array and are different for the various dc motor types. The paper deals with the calculation of the starting to rated current ratio and starting to rated torque ratio of the permanent magnet, separately, series and shunt excited motors when powered by solar cells for the two cases: where (1) the system includes a maximum-power-point-tracker (MPPT) and (2) without an MPPT. Comparing these two cases, one gets a torque magnification of about 3 for the permanent magnet motor and about 7 for other motor types at rated design insolation. The calculation of the torques may assist the PV system designer to determine the advantage of including an MPPT in the system as far as the starting ...

Science.gov (United States)

... ERH moisture cesteats are aumharized on Tables 20 and 21. Moisture sorption isotherme are shewn in Figures XXXI and XXXII. 17 Page 33. ...

British Library Electronic Table of Contents (United Kingdom)

The effect of mean daily air temperature (MDT) on flowering rate (the reciprocal of days to flower) was quantified for 18 species of annual bedding plants. Plants were grown in environmental growth chambers at constant air temperature set points of 5, 7.5, 10, 15, 25, or 30^oC and under an irradiance of 160-180mmolm^-^2s^-^1, with a 16-h photoperiod. Nonlinear mathematical equations were developed to predict the effect of MDT on flowering rate and to estimate the base, optimum, and maximum temperatures (Tmin, Topt, and Tmax), which are the temperatures at which flowering rates are zero (low temperature), maximal, and zero once again (high temperature), respectively. The estimated Tmin varied among species and ranged from 1.1^oC in French marigold (Tagetes patula L.) to 9.9^oC in angelonia ...

UK PubMed Central (United Kingdom)

Background/Aim:To assess the prognostic indicators preoperatively presenting and influencing the mortality rate following esophagectomy for esophageal cancer.Full Text Available

Energy Technology Data Exchange (ETDEWEB)

To determine the effectiveness and patency of percutaneous intervention in insufficient native arteriovenous hemodialysis fistulae (AVFs). Between March 1997 and September 2001, 67 cases of insufficient native AVFs resulted from central vein lesion, PTA was performed in 48 cases, and thrombolytic therapy with or without PTA in 11. In eight of the cases, in which central vein stenosis had led to the insufficency, percutaneous transluminal angioplasty (PTA) was performed, and in three of the eight, a stent was inserted. Angiography findings and complications, as well as success and patency rates in the non-thrombosis and thrombosis group, were evaluated; the central vein lesion group was analysed separately. Among 84 lesions observed at angiography, three were 54 cases of stenosis, 17 of occlusion, and 13 of combined thrombosis. The lesions were located in a proximal vein (n=51), distal vein (n=14), artery (n=6), and at the site of anastomosis (n=13). In the central ...

Science.gov (United States)

In terms of the reduced potential energy barrier ? = ?uTS/kT, the rate coefficients for chemical reactions are usually expressed as proportional to e-?. The coupling between vibrational modes of the medium to the reaction coordinate leads to a proportionality of the regularized gamma function of Euler Q(a,?) = ?(a,?)/?(a), with a being the number of modes coupled to the reaction coordinate. In this work, the experimental rate coefficients at various temperatures for several chemical reactions were fitted to the theoretical expression in terms of Q(a,?) to determine the extent of its validity and generality. The new expression affords lower deviations from the experimental points in 29 cases out of 38 and it accounts for the curvature in the logarithmic plots of rate coefficients versus inverse temperature. In the absence of tunneling, conventional theories predict the curvature of these plots to be identically zero.

UK PubMed Central (United Kingdom)

Neuroleptic malignant syndrome is a life-threatening reaction of neuroleptic medication. The estimated incidence rate of neuroleptic malignant syndrome is between 1% and 1.5% of patients treated with...Full Text Available

Science.gov (United States)

Macrokinetics of benzene sulfonation in liquid-liquid and gas-liquid systems has been studied in continuous mixed reactors. It has been shown that the rate of sulfonation of benzene at 25/sup 0/C in two liquid phases using concentrated sulfuric acid is kinetically controlled. Whereas the rate of the latter reaction by gaseous sulfur trioxide at the same temperature is largely affected by the diffusional phenomena. At this temperature, the rate of reaction in gas-liquid system was described by a model assuming a fast reaction in the liquid phase. However, by increasing the temperature, the fast reaction region gradually changed to instantaneous reaction regime. A model, describing such a regime has also been developed and verified experimentally.

Energy Technology Data Exchange (ETDEWEB)

The kinetic energy transferred to some elements by an electron of kinetic energy 100 to 400 kV is discussed. The displacement rates are compared to the signal generation. (DCL)

International Nuclear Information System (INIS)

(Dec 1971). United States Alexander, DR Antinone, RJ Durham, NH

Energy Technology Data Exchange (ETDEWEB)

A study was made of the kinetics of L-(/sup 3/H)quinuclidinyl benzilate binding with membrane-bound muscarine cholinoreceptors from the rat brain. Determination was made of the rate constants of this process, and constants as a function of ligand concentration was investigated, indicating that there is a complex mechanism of interaction of antagonists with muscarine receptor. With up to 3.5 nM concentrations of L-(/sup 3/H)quinuclidinyl benzilate, the binding reaction occurs in two stages: rapid equilibrated binding is followed by a slow process of conformational isomerization of the receptor-ligand complex. At higher ligand concentrations, there is additional drastic increase in constant of rate of ligand binding a new plateau is reached. Such dependence of rate constant on ligand concentration is indicative of the cooperative nature of interaction between antagonists and muscarine receptors. This is possible if there are ...

British Library Electronic Table of Contents (United Kingdom)

Erosion-corrosion (E-C) of 3003 aluminum (Al) alloy in ethylene glycol-water solutions were studied by weight-loss and electrochemical measurements as well as surface characterization through an impingement jet system. Al alloy E-C is dominated by erosion components, i.e., pure erosion and corrosion-enhanced erosion, which account for 92-97% of the total E-C rate under the various conditions in this work. Contribution from corrosion components, including pure corrosion and erosion-enhanced corrosion, is slight. With the increase of fluid flow velocity and sand concentration, the total E-C rate increases. Compared with the significant increase of the rates of erosion components, the increase of the rate of corrosion component is negligible. Upon fluid flow, passivity of Al alloy that develo...

UK PubMed Central (United Kingdom)

This study was carried out to determine the rate and types of injuries experienced by boardsailors. Results derive from: (a) a review of hospital medical records for water sports injuries, and (b) a...Full Text Available

CERN Document Server

We empirically investigated the relationships between the degree of efficiency and the predictability in financial time-series data. The Hurst exponent was used as the measurement of the degree of efficiency, and the hit rate calculated from the nearest-neighbor prediction method was used for the prediction of the directions of future price changes. We used 60 market indexes of various countries. We empirically discovered that the relationship between the degree of efficiency (the Hurst exponent) and the predictability (the hit rate) is strongly positive. That is, a market index with a higher Hurst exponent tends to have a higher hit rate. These results suggested that the Hurst exponent is useful for predicting future price changes. Furthermore, we also discovered that the Hurst exponent and the hit rate are useful as standards that can distinguish emerging capital markets from mature capital markets.

Energy Technology Data Exchange (ETDEWEB)

A method is described for controlling fuel injection in a diesel engine having a fuel injection nozzle, comprising the steps of: detecting an idling state of the diesel engine and pressure in a combustion chamber; obtaining a pressure increment rate from the pressure detected by the detecting step; selecting a valve opening pressure of the fuel injection nozzle at a relatively low level when the idling state is detected by the detecting step, thereby setting a two peaks characteristics of a fuel injection rate; and controlling the fuel injection nozzle in response to the pressure increment rate so that the pressure increment rate in the combustion chamber is maintained within a predetermined value by changing a fuel injection quantity of a pilot injection from the fuel injection nozzle.

Science.gov (United States)

... technique aBF n-Butyiferrocene P-33 Thermal carbon black PAP Porous Amnmonium Perchlorate Plastinox 711 Antioxidant ...

International Nuclear Information System (INIS)

Understanding the erosion and deposition rates in a small watershed is important for designing soil and water conservation measures. The objective of this study is to estimate the net soil loss and gain at points with various land use types and landform positions in a small watershed in the Sichuan Hilly Basin of China by the 137Cs tracing technique. Among various land use types, the order of erosion rate was bare rock > sloping cultivated land > forest land. The paddy field and Caotu (a kind of cultivated land located at the foot of hills) were depositional areas. The erosion rate under different landform was in this order: hillside > saddle > hilltop. The footslope and the valley were depositional areas. The 137Cs technique was shown to provide an effective means of documenting the spatial distribution of soil erosion and deposition within the small watershed.

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to ...

International Nuclear Information System (INIS)

The energy levels, wavelengths, oscillator strengths, Auger rates and level-to-level dielectronic recombination rate coefficients describing dielectronic recombination into excited levels of Ne-like titanium from F-like low-lying states are calculated. Our calculations are based on Dr. R.D. Cowan's semi-relativistic mass-velocity and Darwin corrections are included in the Hamiltonian, and the distorted-wave model is used for the calculation of free electron wavefunctions. In order to set the recombination rate coefficients on a level by level basis, in a manner compatible with detailed level population kinetics modelling of highly-stripped ions in plasma, the dielectronic recombination rate coefficients as a function of free electron temperatures are given in an analytical form, which is not only very convenient in practice, but also hopefully accurate compared with the exactly calculated numerical ...

International Nuclear Information System (INIS)

Continuing high rates of acidic deposition in the eastern United States may lead to long-term effects on stream communities, because sensitive catchments are continuing to lose anions and cations. A two-year study of the effects of pH and associated water chemistry variables on detrital processing in three streams with different bedrock geology in the Monongahela National Forest, West Virginia were investigated. Leaf pack processing rates and macroinvertebrate colonization and microbial biomass (ATP concentration) on the packs in the three stream were compared. It was found that macroinvertebrate and microbial communities differed both among streams that differed in their capacity to buffer the effects of acidic precipitation and among years in the same stream; these differences in biotic communities were not large enough to affect rates of leaf processing between the two years of the study, but they did significantly ...

International Nuclear Information System (INIS)

(1976). USSR Lupin, VM Ramazanov, PE Tomskij Gosudarstvennyj Univ.

UK PubMed Central (United Kingdom)

Mutation of the gene drop-dead (drd) causes adult Drosophila to die within 2 weeks of eclosion and is associated with reduced rates of defecation...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Flowsheets for the dissolution of aluminum-clad spent nuclear fuel have been proposed using 0.002 M mercuric nitrate catalyst in 5 to 6 M nitric acid. Previous calculations for flammable gas control during the dissolution of spent nuclear fuel have been extended to cover a range of dissolver purge rates from 40 to 55 scfm. A range of dissolver solution volumes from 12000 to 15000 liters were considered for the large H-Canyon dissolver (6.4D). Depending on the purge rate, anywhere from four to six bundles of MURR fuel can be initially charged to the dissolver (6.4D). For successive charges where the dissolver solution already contains 0.002 M mercury catalyst and the dissolved aluminum from five bundles of MURR fuel, five to nine bundles of additional fuel can be charged depending on the purge rate and the dissolver solution volume. Similar calculations have been performed for the small H-Canyon dissolver (6.1D) for solution ...

Science.gov (United States)

... To maximise heat transfer rates, many heatshield designs make use of heat transfer augmentation devices such as large numbers of pin-fin ...

International Nuclear Information System (INIS)

(1971). Poland Gej, B. Szkola Glowna Gospodarstwa Wiejskiego, Warsaw

UK PubMed Central (United Kingdom)

Aging can be defined as a progressive decline in physiological efficiency regulated by an extremely complex multifactorial process. The genetic makeup of an individual appears to dictate this rate...Full Text Available

Science.gov (United States)

The rate of battery use is sometimes even higher in military operations. During Operation Iraqi Freedom, the Marines used more than 3000 single-use ...

Science.gov (United States)

... transformed at 705°C. The cooling rate and temperature dependence of matrix decomposition for Ti6242 was thus similar to that for Ti64 x [9]. ...

Energy Technology Data Exchange (ETDEWEB)

Of some interest is the comparison between the actinide nuclide burning up (fission) rates such as americium 241, americium 242, curium 244, and neptunium 237, in the reactors with fast or thermal neutron spectra.

Energy Technology Data Exchange (ETDEWEB)

In this study based on the mass transfer theory, experiments for the evaporation rates depending on various conditions were carried out through the operation of the existing Natural Evaporation Facility in KAERI. Evaporation media were made of the cotton and polyester. Air circulation in the facility was forced by exhausting fans. The evaporation rate and the decontamination factor were calculated by the result of experiment. The evaporation rate increased as the flow rate of air supply, the feed rate of liquid waste, and the temperature of supplied air increased. As for the humility of supplied air, the evaporation rate was getting higher as the humidity was getting lower. As the result of this study, operation conditions of the Natural Evaporation Facility are optimized as follows; The air temperature above 8C .deg., the air humidity below 70%, the air flow ...

CERN Document Server

Network tomography aims at inferring internal network characteristics based on measurements at the edge of the network. In loss tomography, in particular, the characteristic of interest is the loss rate of individual links. There is a significant body of work dedicated to this problem using multicast and/or unicast end-to-end probes. Independently, recent advances in network coding have shown that there are several advantages from allowing intermediate nodes to process and combine, in addition to just forward, packets. In this paper, we pose the problem of loss tomography in networks that have network coding capabilities. We design a framework for estimating link loss rates, which leverages network coding capabilities and we show that it improves several aspects of tomography, including the identifiability of links, the tradeoff between estimation accuracy and bandwidth efficiency, and the complexity of probe path selection. We discuss the ...

Energy Technology Data Exchange (ETDEWEB)

We wanted to determine the technical and clinical efficacy of using a PTFE-covered self-expandable nitinol stent for the palliative treatment of malignant biliary obstruction. Thirty-seven patients with common bile duct strictures caused by malignant disease were treated by placing a total of 37 nitinol PTFE stents. These stents were covered with PTFE with the exception of the last 5 mm at each end; the stent had an unconstrained diameter of 10 mm and a total length of 50 80 mm. The patient survival rate and stent patency rate were calculated by performing Kaplan-Meier survival analysis. The bilirubin, serum amylase and lipase levels before and after stent placement were measured and then compared using a Wilcoxon signed-rank test. The average follow-up duration was 27.9 weeks (range: 2 81 weeks). Placement was successful in all cases. Seventy-six percent of the patients (28/37) experienced adequate palliative drainage for the remainder of ...

Science.gov (United States)

The change in concentrations of elements due to transmutations resulting from neutron irradiation in the first wall of the ARIES-IV conceptual fusion energy device were determined as a function of neutron dose. SiC burns out at a rate of about 0.5% per effective full power year. The largest impurity concentration is that of He, but several other elements burn in at rates of hundreds of appm/efpy.

Energy Technology Data Exchange (ETDEWEB)

In December 1980, Guenther Rochelt from Munich (FRG) managed the first flight in a solar aircraft. Energy was supplied by 2,500 solar cells with a rated power of 2.2 kW. Self-starting and flying were made possible by a special aircraft construction with an electromotor with a gross power of 1.8 and a rated voltage of 88 V.

International Nuclear Information System (INIS)

In the present work, range and energy loss rate of "2"8Si in four dielectric track detectors viz: Makrofol-KG (MFKG), Makrofol-G (MFG), Triafol-BN (TBN) and LR-115 (cellulose nitrate) have been measured. To calculate these parameters, a curve fitting method was proved to be very useful and easier with more accuracy. (author)

Energy Technology Data Exchange (ETDEWEB)

The horizontal spread of a plume in atmospheric dispersion can be described by the standard deviation of horizontal direction. The widely used Pasquill-Gifford classes of atmospheric stability have assigned typical values of the standard deviation of horizontal wind direction and of the lapse rate. A measured lapse rate can thus be used to estimate the standard deviation of wind direction. It is examined by means of a large dataset of fast wind measurements how good these estimates are. (author) 1 fig., 2 refs.

Energy Technology Data Exchange (ETDEWEB)

We wanted to evaluate the procedural success after percutaneous treatment of thrombosed native arteriovenous dialysis fistula insufficiency and the efficacy of performing mechanical thrombectomy with using the stone basket. From March 2004 to June 2005, 36 thrombosed native hemodialysis access shunts in the upper limbs (brachiocephalic fistulas: 16 and radiocephalic fistulas: 20) were percutaneously treated in 30 patients. Declotting procedures were performed with using urokinase (100,00-200,000 unit) and manual catheter-directed thrombo-aspiration in all the patients. Angioplasty (6 mm in diameter and 4 cm in length) was performed at the identified area of the stenosis and /or with maceration of the thrombus. In 14 cases with massive thrombosis that was refractory to the above mentioned declotting procedures, mechanical thrombectomy with using a Wittich nitinol stone basket (Cook, Bloomington, IN) was performed. Data regarding the procedural success rate and the ...

Energy Technology Data Exchange (ETDEWEB)

The paper presents a description of the physical processes governing the variations of the pulse rise-time which occur during the operation of the proportional counter and are due to varying either the count rate or the applied voltage. On the basis of the rise-time concept the differences in the count rate effect observed in various types of proportional counters are discussed.

Energy Technology Data Exchange (ETDEWEB)

The use of charcoal canisters in the measurement of radon emanation rates from surfaces is discussed. The counting efficiency of the canisters is dependent upon the volume of activated charcoal used, varying from approximately 0.7% for a full canister to 1.3% for a canister filled to only 1/3 of its capacity. The inclusion of Si-Gel desiccant reduces the radon collection efficiency of the canister.

UK PubMed Central (United Kingdom)

BackgroundMore optimistic perceptions of cardiovascular disease risk are associated with substantively lower rates of cardiovascular death among men. It remains unknown whether this...Full Text Available

Wastenet

...] gueconwpa~05-05-05 How is Macro News Transmitted to Exchange Rates? (December 2003) by Martin D. D. Evans(Georgetown University and NBER) and Richard K. Lyons(U.C. Berkeley and NBER, Haas School of Business) [Downloadable!] gueconwpa~05-05-04 A New Micro Model of Exchange Rate Dynamics (March 2004) by Martin D. D. Evans(Georgetown University and ...

Science.gov (United States)

Polymer matrix composites are presently used in many fields due to their excellent mechanical properties such as high specific strength and stiffness. However, not much is known of these composites' response to impact loading, which usually occurs at strain rates much higher than the strain rates used to measure the quasi-static mechanical properties of materials. The use of static properties in the study of structures that undergo dynamic loading can produce excessive design weight or cause unexplained and untimely failure. The studies included in this dissertation provide the results of Split Hopkinson Pressure Bar experiments to determine the ultimate compressive strength and strain of composites at high strain rates. Most researchers are using specimens with different dimensions and geometry. For this reason, it is difficult to compare results of tests done by different people. Herein, the Split Hopkinson Pressure Bar ...

Science.gov (United States)

We present an estimate of the Gamma Ray Bursts which should be expected from metal-free, elusive first generation of stars known as PopulationIII (PopIII). We derive the GRB rate from these stars from the Stellar Formation Rate obtained in several Reionization scenarios available in the literature. In all of the analyzed models we find that GRBs from PopIII are subdominant with respect to the ''standard'' (PopII) ones up to z {approx} 10.

Science.gov (United States)

Analytical techniques for analyzing the effects of ship motion and attitude on the primary coolant system flow rates are presented. Design data for minimizing these effects are given. (C.J.G.)

International Nuclear Information System (INIS)

The beneficial effect of compost application to the sandy soil on dry matter production of shoots and fruits as well as its effect on l5N-uptake and nitrogen utilization percent of cucumber plant (Cucumis sativus L.) were studied under field conditions. Two types of natural compost (i.e. sugar cane bagasse (SC) and beet compost (BC)) with three levels (2, 4, 6 ton/fed) in addition to check treatment for each kind of compost (sheep manure with rate of 20 in/fed) combined with three rates of nitrogen fertilizer rates (50, 75, 100% from the recommended rate, i.e. 75 kg /fed) were used. The bagasse compost in both seasons gave a significantly higher response than the beet compost. There was a greet reduction in cucumber dry weight, N yield, Ndff%, FN yield and N utilization % of shoots and fruits as the level of compost application decreased. However, cucumber plants grown on high compost application level ...

CERN Document Server

We derive the expression for spontaneous emission rate in finite one-dimensional photonic crystal with arbitrary defects using the effective resonator model to describe electromagnetic field distributions in the structure. We obtain explicit formulas for contributions of different types of modes, i.e. radiation, substrate and guided modes. Formal calculations are illustrated with a few numerical examples, which demonstrate that the application of effective resonator model simplifies interpretation of results.

Energy Technology Data Exchange (ETDEWEB)

The part of the FFTF Reactor Characterization Program reported in this paper is a measurement of absolute fission rates of eight major fuel isotopes at two different positions within the reactor. The instruments employed in these tests were fission ionization chambers for which the absolute efficiency and fissionable deposit mass assay have been rigorously established.

Energy Technology Data Exchange (ETDEWEB)

This program is designed in order to calculate electricity generation cost by different energy sources, and menu type is adopted for user convenience. This program also graphically shows the share of capital investment cost, O and M cost, and fuel cost. Sensitivity analysis about discount rate can also be carried out by this program, taking into consideration the important role of the discount rate in the generation costs calculation. (Author) 7 refs., 1 fig., 3 tabs.

UK PubMed Central (United Kingdom)

Using QCT, we made a longitudinal, population-based assessment of rates of bone loss over life at the distal radius, distal tibia, and lumbar spine. Cortical bone loss began in perimenopause in women...Full Text Available

International Nuclear Information System (INIS)

Research highlights: #-># The Y-intermetallic can accelerate corrosion and Y can increase the protectiveness of the surface layer. #-># In 0.1 M NaCl, the corrosion rate of Mg-Y alloys increased with increasing Y due to the Y intermetallic. #-># In 0.1 M NaCl, there was filiform corrosion. #-># In 0.1 M Na_2SO_4, the corrosion rate of Mg-Y alloys decreased with increasing Y in the range 3-7%Y. #-># Hydrogen evolution was observed from particular parts of the alloy surface. - Abstract: Corrosion of Mg-Y alloys was studied using electrochemical evaluations, immersion tests and direct observations. There were two important effects. In 0.1 M NaCl, the corrosion rate increased with increasing Y content due to increasing amounts of the Y-containing intermetallic. In 0.1 M Na_2SO_4, the corrosion rate decreased with increasing Y content above 3%, attributed to a more protective surface film, ...

International Nuclear Information System (INIS)

Tarapur Atomic Power Station Unit-3 and 4 (TAPS -3 and 4) are the 540 MWe reactors. Unit-4 attained first criticality on 06th March 2005 and operated for about 230 effective full power days (EFPD). Unit-3 attained first criticality on 21st May 2006 and operated for about 20 EFPD. With the reactor operation radiation field increases on the Primary Heat Transport system equipments, Moderator system equipments and auxiliary system equipments due to deposition of fission products and activation products in different reactor systems. These dose rates significantly contributes to the external exposure and stations collective dose during reactor operation, refueling operation and maintenance activities. A study was undertaken at TAPS 3 and 4 to identify the system equipments showing the significant dose rates and identify the radionuclides present in the primary heat transport system, Moderator systems, cover gas system and other auxiliary system for ...

International Nuclear Information System (INIS)

An experimental investigation of a humidification-dehumidification desalination (HDD) process using solar energy at the weather conditions of Suez City, Egypt, is presented. A test rig is designed and constructed to conduct this investigation under different environmental and operating conditions. The test rig consists of a solar water heater (concentrator solar collector type), solar air heater (flat plate solar collector type), humidifier tower and dehumidifier exchanger. Different variables are examined including the feed water flow rate, the air flow rate, the cooling water flow rate in the dehumidifier and the weather conditions. Comparisons between the experimental results and other published results are presented. It is found that the results of the developed mathematical model by the same authors are in good agreement with the experimental results. The tested results show that the productivity of the system is ...

Energy Technology Data Exchange (ETDEWEB)

The drilling rate of rotary percussion drill bit depends on the revolving energy and the impact energy of drifter as well as the characteristics of rock mass. The rotary percussion drill tests were executed in-situ for 13 kinds of rock mass using 12 actual drill machines to clarify the interrelations between them. At the result, the drilling rate has been expressed as the function of the revolving energy, the impact energy, the bit diameter, the coefficient of crack of rock mass and the Shore hardness or the amount of Los Angeles abrasion or the radial compressive strength of rock specimen. On the other hand, the rock mass properties could be determined by measuring the drilling rate of a standard rotary percussion drill machine. The relationship between the different drilling thrusts and the impact energy has been revealed. As a result, it has been found that the impact energy exerts a greater influence on the drilling ...

British Library Electronic Table of Contents (United Kingdom)

In the current study, we have determined how potassium rate affects the phenolic levels and antioxidant properties of three cultivars of basil (Ocimum basilicum L.) leaves: Dark Opal, Sweet Thai, and Genovese. Potassium rate increased the total phenolic concentration in basil, with basil treated at the highest potassium rate, 5.0mMK, containing greater phenolic levels than basil treated at the lowest potassium rate, 1.0mMK (p=0.008). Basil grown at 5.0mMK also had higher concentrations of rosmarinic (p=0.005) and chicoric (p<0.001) acids compared to lower potassium treatment levels. Correspondingly, 1.0mMK basil had lower DPPH (2,2prime-diphenyl-1-picrylhydrazyl) (p0.005) and FRAP (ferric reducing antioxidant power, p=0.043) antioxidant capacities compared to basil treated at higher potass...

CERN Document Server

Neutrino emission drives neutron star cooling for the first several hundreds of years after its birth. Given the low energy ($\\sim$ keV) nature of this process, one expects very few nonstandard particle physics contributions which could affect this rate. Requiring that any new physics contributions involve light degrees of freedom, one of the likely candidates which can affect the cooling process would be a nonzero magnetic moment for the neutrino. To illustrate, we compute the emission rate for neutrino pair bremsstrahlung in neutron-neutron scattering through photon-neutrino magnetic moment coupling. We also present analogous differential rates for neutrino scattering off nucleons and electrons that determine neutrino opacities in supernovae. Employing current upper bounds from collider experiments on the tau magnetic moment, we find that the neutrino emission rate can exceed the ...

Energy Technology Data Exchange (ETDEWEB)

Radiation-and-thermal-combined degradation of ethylene-propylene rubber (EP rubber) and chlorosulfonated polyethylene (CSM) as cable insulating and jacketing materials were evaluated by accelerated aging tests and a method to assess the lifetime of these materials under practical application was studied. EP rubber and CSM of experimental formulation were degraded at accelerated rates, that are 50 [approx] 1000 times the degradation rate under a standard condition (1Gy/h, 50degC). The degradation was investigated by measuring the tensile properties. In the accelerated aging tests, rates of elongation decrease owing to degradation for both EP rubber and CSM were in proportion to increase in accelerated rate. Behaviors of elongation changes showed little difference with accelerated rate. EP rubber lifetime estimated from sequential aging test had a tendency to extend beyond that from ...

Energy Technology Data Exchange (ETDEWEB)

Pacific Gas & Electric Co.`s (PG&E`s) Delta district, approximately 45 miles northeast of the San Francisco Bay Area, is a fast growing residential community with peak demand occurring between 6 and 7 PM in hot summer weekdays. In the early 1990s, PG&E`s system planners projected a need to build a new substation in 1996 to meet the local peak electricity demand. In 1991, as part of a new distribution planning and capital investment process, PG&E launched its innovative Model Energy Community (MEC or Delta) program to test whether the inclusion of new, experimental rates and geographically-targeted cost-effective energy-efficiency measures could reduce the local peak demand and therefore defer major substation and T&D capital investment. Two new residential TOU rates were designed and implemented in PG&E`s Delta area between 1991 and 1993. This paper discusses the market assessment activities and results for these ...

Energy Technology Data Exchange (ETDEWEB)

The technology of minor actinide recycling in fast reactors has been discussed. In CEA, the feasibility study on Am once-through recycling in Phenix core with the moderated target subassemblies (S/As) has been performed. In this report, the evaluation of the heterogeneity effect on the moderated target S/As is described. It was evaluated by the calculation with the continuous energy Monte-Carlo code, MVP, because the accuracy of the deterministic method for the moderated target S/As is unknown. The reaction rates of four isotopes (Am-241, Am-242, Am242m and Am-243) calculated with the heterogeneous model and the homogeneous one were compared. These four isotopes play the important role in Am incineration. It is seen that the homogeneous model overestimates the reaction rates of Am-241 and Am-243 by 4 - 13%, and underestimates those of Am-242 and Am-242m by 13 - 23%. Further investigation made it clear that the overestimation of Am-241 and ...

Scientific Electronic Library Online (English)

Abstract in english The rate of copper II/zinc cementation from copper sulphate solutions in the absence and in the presence of methanol (CH3OH) and dimethyl sulphoxide (DMSO) has been studied and the reaction was found to follow first-order kinetics. The influence of several parameters on the course of the reaction, such as cylinder rotation speed, initial concentration of Cu2+ ions, temperature and concentration of organic solvent, was investigated. In the case of CH3OH, rotating zinc cyli (more) nder was used, while in the presence of DMSO stationary zinc sheet and rotating zinc cylinder were used. It was found that (1) the percentage inhibition caused by methanol ranged from 10.70 to 58.38 depending on the concentration of the alcohol used; (2) the rate of cementation in the presence of DMSO using rotating zinc cylinder > the rate of cementation in the presence of DMSO using stationary zinc sheet; (3) the ...

Energy Technology Data Exchange (ETDEWEB)

The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was ...

Energy Technology Data Exchange (ETDEWEB)

The degradation status of outlet feeders in Wolsung unit 1 is analyzed using feeder thickness measurement data during overhaul period in 2000. DBs related to feeder thinning are made for parameters affecting dissolution rate and parameters affecting mass transfer rate. The initial thickness of feeder in Wolsung unit 1 is analyzed using initial thickness data of Wolsung unit 2, 3 and 4 as there are no initial thickness data of Wolsung unit 1. The initial thickness is varied as feeder diameter and bending degree, and CANDU feeders can be divided as 3 types for 2.5'' feeders and 3 types for 2'' feeders. The average initial thickness value for each type is defined as the initial thickness value of the type for Wolsung unit 1 feeders. Thinning rate is evaluated as the value dividing difference between initial thickness and minimum measured thickness by operation time. It is found that the ...

Energy Technology Data Exchange (ETDEWEB)

Quantitative bone scintigraphy was performed at 4 and 24 h after injection of {sup 99m}Tc-MDP. The lower thoracic and all the lumbar vertebrae were recorded in 37 patients with prostatic carcinoma before orchiectomy as well as two weeks, two and six months postoperatively. Fourteen patients had normal bone scintigrams. By means of the measured variation in the count rate between normal vertebrae, the criterion for a vertebra to be considered as abnormal was determined using the 4 h-uptake values. For patients with normal scintigrams the count rate at 24 h was below the 4 h level and the mean 24 h/4 h ratio was determined to be 0.85 {+-} 0.09 (1 SD). Normal vertebrae in patients with skeletal metastases had only slightly lower count rate values at 24 h than at 4 h. Abnormal vertebrae showed a higher count rate at 24 h, especially two weeks postoperatively, while a tendency towards lower values than at 4 ...

Science.gov (United States)

We used a dense phase tower as the reactor in a novel semi-dry flue gas desulfurization process to achieve a high desulfurization efficiency of over 95% when the Ca/S molar ratio reaches 1.3. Pilot-scale experiments were conducted for choosing the parameters of the full-scale reactor. Results show that with an increase in the flue gas flow rate the rate of the pressure drop in the dense phase tower also increases, however, the rate of the temperature drop decreases in the non-load hot gas. We chose a water flow rate of 0.6 kg/min to minimize the approach to adiabatic saturation temperature difference and maximize the desulfurization efficiency. To study the flue gas characteristics under different processing parameters, we simulated the desulfurization process in the reactor. The simulated data matched very well with the experimental data. We also found that with an increase in the Ca/S molar ratio, the ...

Energy Technology Data Exchange (ETDEWEB)

In the latter half of 2005, the U.S. Environmental Protection Agency (USEPA) published a Proposed Rule (40 CFR Part 197) for establishing a dose rate standard for limiting radionuclide releases from the proposed Yucca Mountain high-level radioactive waste repository during the time period from 10{sup 4} to 10{sup 6} years after closure. The proposed standard was based on the difference in the estimated total dose rate from natural background in the Amargosa Valley and the ''average annual background radiation'' for the State of Colorado. As defined by the USEPA, ''natural background radiation consists of external exposures from cosmic and terrestrial sources, and internal exposures from indoor exposures to naturally-occurring radon''. On the basis of its assessments, the USEPA estimated that the difference in the dose rate in the two identified areas ...

International Nuclear Information System (INIS)

International standards and guidelines for calibrating high-dose dosimetry systems to be used in industrial radiation processing recommend that dose-rate effects on dosimeters be evaluated under conditions of use. This is important when the irradiation relies on high-current electron accelerators, which usually provide very high dose-rates. However, most dosimeter calibration facilities use low-intensity gamma radiation or low-current electron accelerators, which deliver comparatively low dose-rates. Because of issues of thermal conductivity and response, portable calorimeters cannot be practically used with high-current accelerators, where product conveyor speeds under an electron beam can exceed several meters per second and the calorimeter is not suitable for use with product handling systems. As an alternative, Monte Carlo calculations can give theoretical estimates of the absorbed dose in materials with flat or complex ...

Energy Technology Data Exchange (ETDEWEB)

Activation reactions of coal reject-derived char (CRC) with CO{sub 2}, H{sub 2}O and air are experimentally studied using a thermogravimetric analysis technique. The experimental kinetic data are treated via kinetic data unification based on the half-time, and the intrinsic rate constants are extracted by the modified Arrhenius plot method. The effect of structural evolution on the overall rate changes is modelled with a modified random pore model and percolation model taking into account the ash content of the coal reject char. It is found that the relative reaction rates for the reaction pairs CO{sub 2}-CRC, H{sub 2}O-CRC and air-CRC are at an increasing order of sequence at a given temperature. The effect of gaseous pressure on the reaction rate is shown to be significant for CO{sub 2}-CRC and H{sub 2}O-CRC reactions. It has shown that both models can predict well the maximum ...

Science.gov (United States)

Nitrate microelectrodes and ORP microelectrodes were fabricated to study the denitrification characteristics of dynamic membrane at different COD loadings. The denitrification process was found at 0.6-1 mm depth beneath the interface of biofilm/bulk. The results of ORP microelectrode also demonstrated that the ORP value in the range of denitrification area was between 88.6 approximately -128.4 mV which was appropriate to denitrification. When the COD loading was 0.45 kg/(m3 x d), the denitrification rate (NO3- -N) was the maximum of 0.6347 x 10(-6 mol/(L x s). With the increase of COD loading, the denitrification area was increasing and two layers with different denitrification rates emerged in the dynamic membrane. The phenomenon implied the effect of organic concentration, oxygen concentration and bacterial competition on the denitrification rate. PMID:17117632

International Nuclear Information System (INIS)

This paper describes a series of tests investigating two-phase flow regimes in a transparent model of a PWR hot leg. Test conditions were selected to cover a wide range of gas and liquid superficial velocities (.01 m/s 2 m/s) were also performed for comparison with semi-analytical predictions. Results include average void fractions, flow rates, and visual characterizations of the two-phase flow phenomena. Results show generally good agreement with Taitel and Duckler flow regime map and Zuber-Findlay correlation for average void fraction in vertical pipes. Results also indicate that flow regimes and collapsed liquid level (void fraction) are more strongly dependent on air flow rate (air superficial velocity) than water flow rate (water superficial velocity).

International Nuclear Information System (INIS)

During the normal operation of a Nuclear Power Plant (NPP), radioactive releases into the atmosphere will be in small quantities. During major accidental situations, though the probability is extremely small, there may be significant release of radioactivity to the environment through the stack or at ground level. To study the external radiation exposure, if any, to the members of public due to releases during the normal operation of a nuclear power plant (NPP) and also to meet the requirement of emergency preparedness for the NPP site, continuous recording and analysis of environmental dose rate data is essential. This paper presents analysis of the gamma dose rates recorded by the Environmental Dose Logging Systems (EDLS) installed around the site during the last six years in the Emergency Planning Zone (EPZ) of Tarapur Atomic Power Station (TAPS). (author)

Energy Technology Data Exchange (ETDEWEB)

Unlike the conventional automotive, modem railway trains are designed with non-openable windows; and a mechanical ventilation and air-conditioning (MVAC) system is installed in each train compartment for better indoor air quality as well as to provide a thermally comfortable environment. The ventilation rate is no doubt a critical element in the design of a MVAC system, especially in Hong Kong where the daily passenger load is extremely heavy. Earlier studies illustrated that carbon dioxide can be controlled at 1000 ppm by increasing the ventilation rate to 25.2 m{sup 3} h{sup -1}; however, it will also lead to an increase in energy consumption. In this paper, the electrical energy consumption at various ventilation rates was studied, and the cost of maintaining a low carbon dioxide level was estimated These provide solid information for the local railway companies to improve the air quality inside the train compartments. ...

Energy Technology Data Exchange (ETDEWEB)

This paper summarizes the current scientific evidence that improved indoor environmental quality can improve work performance and health. The review indicates that work and school work performance is affected by indoor temperature and ventilation rate. Pollutant source removal can sometimes improve work performance. Based on formal statistical analyses of existing research results, quantitative relationships are provided for the linkages of work performance with indoor temperature and outdoor air ventilation rate. The review also indicates that improved health and related financial savings are obtainable from reduced indoor tobacco smoking, prevention and remediation of building dampness, and increased ventilation. Example cost-benefit analyses indicate that many measures to improve indoor temperature control and increase ventilation rates will be highly cost effective, with benefit-cost ratios as high as 80 and annual ...

British Library Electronic Table of Contents (United Kingdom)

To test the hypothesis that leaf level photosynthetic related traits might confer late successionals a competitive advantage over early successionals in low light growth conditions, steady photosynthetic assimilation and dynamic photosynthetic induction related traits were examined in low light grown seedlings with contrasting successional status. Compared with the early successionals, late successionals as a group significantly exhibited lower leaf gas exchange rates. While late successionals required a longer time to respond to simulated sunflecks, they had lower rates of induction losses after sunflecks. Such photosynthetic induction traits allowed late successionals to more effectively utilize subsequent sunflecks. It was observed that plants with lower gas exchange rates responded mor...

International Nuclear Information System (INIS)

Long term indoor radon gas measurements using a passive monitor were conducted in the basement rooms of five hospitals, which are built in the Tokyo metropolitan area. The ventilation rate averaged over all hospital was 12.3 air change per hour (ACH). The highest radon concentration was 56.3 Bq/m"3. The value averaged concentration over all hospital and all season was 20 Bq/m"3. But the average of the two hospitals were twice as high as those of three others. Since the total ventilation rate integrated over a day is not different much, the reason of the concentration difference is considered to be the difference in radon emission rate from concrete wall and soil of the each hospital. Though we inquired workers about 'Environmental complaints', it do not show the direct relation between radon and environmental complaints. (author)

Energy Technology Data Exchange (ETDEWEB)

Measurements of neutron and gamma-ray penetrations in an iron shield were performed up to a 60-cm depth in a tightly coupled source shield configuration with the fast-neutron reactor YAYOI as a source. Rates of neutron reactions and gamma-ray dose rates in the iron shield were obtained using activation foils and thermoluminescent dosimeters. Analyses of the experiments were made by using the DOT-III code with coupled neutron and gamma-ray cross sections from ENDF/B-IV and POPOP4 libraries. To obtain the source condition for the iron shield analyses, the calculated spectrum was adjusted to the measured reaction rates at the reactor shield boundary. The calculated neutron and gamma-ray distributions in the iron shield show fairly good agreement with the experiments. The effect of difference in Bondarenko-type self-shielding factors on the analyses of the iron shield is also shown.

International Nuclear Information System (INIS)

In the formation of A-15 superconducting compounds by solid state diffusion, the time exponent in the growth law under different experimental conditions varies widely from about 0.25 to 1.0. Specific models of growth for different operative rate-controlling conditions are proposed. When the diffusion of B atoms in the matrix is rate-controlling, the thickness of the reacted compound layer increases as tsup(1/2) or tsup(2/3). When the diffusion of B atoms through the compound layer is rate controlling, a tsup(1/2) dependence both for bulk diffusion and grain-boundary diffusion is predicted. When substantial grain growth occurs in the reacted layer during the diffusion anneal, the time exponent observed could be as low as 1/4. Experimental data in support of the predictions of the proposed models are presented. (author).

International Nuclear Information System (INIS)

Local control of Ewing's sarcoma was analysed in a series of 67 patients treated by surgery and/or radiotherapy as well as combination chemotherapy. Radiotherapy was employed with or without surgery in 60 patients and produced an overall local control rate of 55%; complete excision of the primary lesion seemed to be beneficial. There was a marked variation in control rates depending on the site of the primary lesion: limb 85%, rib 53%, pelvis 31% and other sites 33%.Primary tumours greater than 10 cm in diameter were significantly less likely to be controlled. Using daily fractions of approximately 180 cGy, total doses in excess of 6000 cGy seem more likely to produce serious late morbidity amd may not increase the local control rate. No cases of second malignancy arising in irradiated tissue have been observed to date, but one patient developed acute lymphoblastic leukaemia. (author).

Energy Technology Data Exchange (ETDEWEB)

In order to match the output capacity of a geothermal heat pump system (GHPS) with the actual load requirement, research has been carried out in finding the influence of two systematic parameters, the water flow rate inside the condenser and the compressor input frequency on the GHPS operation. Experiments are done on a small-scale GHPS at the water flow rate ranging from 0.054 kg/s to 0.174 kg/s and the frequency from 30 Hz to 55 Hz. The analysis of the experimental data reveals the relationships among the compressor frequency, the water flow rate and other important parameters such as coefficient of performance (COP), heat capacity and compressor power input. The conclusions in the paper can serve as some guidance to the load adjustment of GHPS. (author)

Science.gov (United States)

Forced convective heat transfer in a cross-corrugated channel solar air heater has been studied experimentally using air as a working fluid. The channel was formed by two transversely positioned corrugated sheets and two flat thermally insulated side walls. One corrugated sheet was heated by a radiant heater, while the other was thermally insulated. The fluid velocity and temperature, and the wall temperature and the local heat flux across the heated corrugated sheet were measured for a variety of operating flow rates. Experimental results for the channel geometry have yielded the correlation Nu = 0.0743 (Re)[sup 0.76]. This heat-transfer coefficient is about 2.8 times that of a smooth flat channel. The experiments showed that local heat transfer rate was smaller on the valley of the corrugation than that on the peak. The ratio of the local heat transfer rates on the two locations was related to the Reynolds number.

British Library Electronic Table of Contents (United Kingdom)

The CO2 adsorption capacity of the low-cost solid sorbents of waste tire char (TC) and chicken waste char (CW) was compared with commercial active carbon (AC) and 5?? zeolite (ZA) using thermogravimetric analysis (TG), pressurized TG, and differential scanning calorimetry (DSC). The sorbents were degassed in a TG up to 150??C to release all gases on the surface of the sample, then cooled down to the designed temperature for adsorption. TG results indicated that the CO2 adsorption capacity of TC was higher than that of CW, but lower than those of AC and ZA. The maximum adsorption rate of TC at 50??C was 0.61% min?1, lower than that of AC, but higher than that of CW, 0.44% min?1. The maximum adsorption rate of ZA at 50??C was 3.1% min?1. When the pressure was over 4?bar, the adsorption rate ...

British Library Electronic Table of Contents (United Kingdom)

This paper explores the through-/in-plane characteristics of water transport in the cathode gas diffusion layer (GDL) of a polymer electrolyte fuel cell (PEFC). Theoretical analysis is performed on the non-isothermal two-phase flow under flow channels. A dimensionless group Da (Damkohler number for PEFC operation), defined as the ratio of water generation rate to water vapor-phase removal rate, is formulated to characterize the flow regimes in a PEFC. This group, lumping geometrical parameters and physical properties, compares the water vapor-phase removal capability (via water diffusion and holding capacity) with the rate of water production by the oxygen reduction reaction. We find that this dimensionless group can be used to characterize the non-isothermal, two-phase phenomena: when Da&...

British Library Electronic Table of Contents (United Kingdom)

Using a sample of Uruguayan manufacturing establishments we analyze employment, capital, and productivity dynamics over a period of currency appreciation; changes in trade policy; and changes in the institutional setting of wage negotiations. As the relative capital-labor price ratio fell, capital intensity increased. At the same time, there was an increase in labor and total factor productivity. Creation and destruction rates were relatively high and pervasive over time, sectors, establishment size, and establishment age, with exits explaining a sizeable part of destruction rates. Most of the excess reallocation was due to movements -within- rather than -between- sectors. Thus, high reallocation rates were linked to establishment-level heterogeneity rather than aggregate shocks.

International Nuclear Information System (INIS)

The corrosion behavior of the sputter-deposited amorphous or nanocrystalline W-Nb alloys is studied in 10% NaCl, 0.1 and 1 M NaOH solutions at 24 deg. C, open to air using immersion tests and electrochemical measurements. Niobium metal acts synergistically with tungsten in enhancing the corrosion resistance of the W-Nb alloys so as to show lower corrosion rates than the corrosion rates of the alloy-constituting elements in almost all examined solutions. Corrosion rates of W-Nb alloys are about more than one order of magnitude less than that of the sputter-deposited tungsten and even lower than that of sputter-deposited niobium. The stability of the anodic passive films formed on the W-Nb alloys increase with niobium content.

British Library Electronic Table of Contents (United Kingdom)

Many high-strain-rate compression measurements (2000 per second) using a specially designed split Hopkinson pressure bar (SHPB) for the plastic-bonded explosive PBX9501 have been reported in the literature, but there is a sparsity of data for a United Kingdom polymer-bonded explosives (PBX) known as EDC37. Both EDC37 and PBX9501 are cyclotetramethylenetetranitramine-based (HMX-based) PBXs with high filler contents. The binder systems for the PBXs are very different: EDC37 consists of a nitroplasticized nitrocellulose and PBX9501 a nitroplasticized ESTANE. PBX9501 exhibits nearly invariant fracture strains of ?1.5?pct as a function of temperature at high strain rates, whereas EDC37 fails at ?2 to 2.5?pct. The maximum compressive strengths for both PBXs were measured at 150?Mpa at ?55??C, bu...

International Nuclear Information System (INIS)

Composite materials of synthetics (based on monomers, oligomers and thermoplastics) and of natural polymers (wood and other fibrous cellulosics) prepared by radiation processing, offer valuable structural materials with enhanced coupling forces between the components. The applied polymer chemistry of such composites shows several common features with that of radiation grafting. E.g. the polymerization rate of oligomer-monomer mixtures in wood remains in most cases proportional to the square-root of the initiating dose-rate, just as in the simultaneous grafting, demonstrating that the chain termination kinetics remain regularly bimolecular in the corresponding dose-rate ranges. In the processing experiences of such composites, low dose requirement, easy process-control, and good technical feasibility have been found for composites of wood with oligomer-monomer mixtures, for coconut fibres with unsaturated polyesters and for ...

International Nuclear Information System (INIS)

Mitsubishi is developing a new type of accumulator incorporating the technology of fluidics as one of the seeds for the improved safety of the newly constructed pressurized water reactor plants. This accumulator employs a vortex flow control device, called a vortex damper, as a fluidic device to simplify the safety systems. A fundamental experimental study with a one-fifth scale model and confirmation tests with a one-third scale model to develop the vortex damper have been carried out, and satisfactory results have been achieved. The results of the confirmation tests under the prototype pressure conditions agree well with the basic tests. The flow rate ratio can be 5 to 6. The pressure loss coefficient in the large flow rate period is 8. A cavitation factor is the main parameter of the flow rate coefficient.

CERN Document Server

Radiation protection of the personnel who will perform interventions in the LHC Beam Cleaning Insertions is mandatory and includes the design of equipment and the establishment of work procedures. Residual dose rates due to activated equipment are expected to reach significant values such that any maintenance has to be planned and optimized in advance. Three-dimensional maps of dose equivalent rates at different cooling times after operation of the LHC have been calculated with FLUKA. The simulations are based on an explicit calculation of induced radioactivity and of the transport of the radiation from the radioactive decay. The paper summarizes the results for the Beam Cleaning Insertions and discusses the estimation of individual and collective doses received by personnel during critical interventions, such as the exchange of a collimator or the installation of Phase 2. The given examples outline the potential and the need to optimize, in an ...

CERN Document Server

Microbonding of the CMS Tracker Inner Barrel (TIB) and Tracker Inner Disks (TID) modules was shared among six different Italian Institutes. The organization devised and the infrastructure deployed to handle this task is illustrated. Microbonding specifications and procedures for the different types of TIB and TID modules are given. The tooling specially designed and developed for these types of modules is described. Experience of production is presented. Attained production rates are given. An analysis of the microbonding quality achieved is presented, based on bond strengths measured in sample bond pull tests as well as on rates of bonding failures. Italian Bonding Centers routinely performed well above minimum specifications and a very low global introduced failure rate, at the strip level, of only $\\sim$0.015 \\% is observed.

CERN Document Server

The work identifies the first lattice decoding solution that achieves, in the general outage-limited MIMO setting and in the high-rate and high-SNR limit, both a vanishing gap to the error-performance of the (DMT optimal) exact solution of preprocessed lattice decoding, as well as a computational complexity that is subexponential in the number of codeword bits. The proposed solution employs lattice reduction (LR)-aided regularized (lattice) sphere decoding and proper timeout policies. These performance and complexity guarantees hold for most MIMO scenarios, all reasonable fading statistics, all channel dimensions and all full-rate lattice codes. In sharp contrast to the above manageable complexity, the complexity of other standard preprocessed lattice decoding solutions is shown here to be extremely high. Specifically the work is first to quantify the complexity of these lattice (sphere) decoding solutions and to prove the surprising result ...

Energy Technology Data Exchange (ETDEWEB)

The bulk removal of CO/sub 2/ from industrial gases is a frequently applied process in the field of gas-treating. Usually chemical solvents are used in order to increase both the solvent-loading capacity and the absorption rate. These solvents often are aqueous solutions of alkanolamines. The loaded-liquid is regenerated at high temperatures with the aid steam. In the present study absorption rates are experimentally determined in various mixtures of amines over a wide range of concentrations. Simultaneously, a model was developed for the description of mass transfer accompanied by parallel reversible chemical reactions. The equations of this mass transfer model could not be solved analytically and therefore numerical techniques were used to obtain an exact description of this process. This model also includes the asymptotic situations of homogeneous catalysts and shuttle mechanism for which in the literature several approximate solutions have ...

International Nuclear Information System (INIS)

The widespread use of building materials with relatively high radium concentrations may increase population exposure. A method is presented for measuring effective diffusion coefficients and exhalation rates of radon from such materials. Equations for use in the experimental determination of these values are obtained theoretically. The experimental set-up consists of a container which is hermetically sealed to a slab of the building material. Nitrogen is blown through the container and then through an ionization chamber which is connected to an electrometer and X-Y plotter, and the radon concentration is measured continuously. Exhalation rates of radon from some major building materials measured by this method will be used as reference levels. The method can also be used to determine other properties such as porosity. (author).

British Library Electronic Table of Contents (United Kingdom)

The survival of acetabular components depends on several factors: wear, osteolysis and septic or aseptic loosening. Osteolysis seems to be the main cause for concern in cementless arthroplasties. Acetabular osteolysis results from particle debris and segmental unloading of acetabular bone by rigid sockets. We investigated a cementless elastic monoblock socket with regard to acetabular osteolysis and aseptic loosening in a cohort of young patients. We evaluated 158 hip arthroplasties with a minimum follow-up of ten?years (ten to 18) and a mean age of 42?years (18?50). The overall revision rate at 14?years was 80% with a 98% survival rate for aseptic loosening. The mean polyethylene wear rate was 0.11?mm/year. Progressive acetabular osteolysis was seen in 3% of patients evaluated. In conclus...

Energy Technology Data Exchange (ETDEWEB)

Experience with multiwire proportional chambers at high rates at the Argonne Zero Gradient Synchrotron is described. A buildup of silicon on the sense wires was observed where the beam passed through the chamber. Analysis of the chamber gas indicated that the density of silicon was probably less than 10 ppM.

UK PubMed Central (United Kingdom)

Coupled rat heart mitochondria produce externally hydrogen peroxide at the rates which correspond to about 0.8 and 0.3 per cent of the total oxygen consumption at State 4 with succinate and...Full Text Available

UK PubMed Central (United Kingdom)

A common property of aging in all animals is that chronologically and genetically identical individuals age at different rates. To unveil mechanisms that influence aging variability, we identified markers...Full Text Available

UK PubMed Central (United Kingdom)

Background and AimsIn spatially heterogeneous environments, a trade-off between seedling survival and relative growth rate may promote the coexistence of plant species. In temperate...Full Text Available

UK PubMed Central (United Kingdom)

Assessments of drinking water safety rely on the assumption that ingestion represents the principal route of exposure. A review of the experimental literature revealed that skin penetration rates for...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundResponse shift theory suggests that improvements in health lead patients to change their internal standards and re-assess former health states as worse than initially rated...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundDuring the last ten years, major advances have been made in characterizing and understanding the evolution of mitochondrial DNA, the most popular marker of molecular biodiversity....Full Text Available

UK PubMed Central (United Kingdom)

BackgroundCaesarean section is one of the most commonly performed operations on women throughout the world. Rates have increased in recent years – about 20–25% in...Full Text Available