Energy Technology Data Exchange (ETDEWEB)

The Cryocycling of Energetic Materials Project is sponsored by the Memorandum of Understanding (MOU) on advanced munition technologies. This MOU is an agreement between the Department of Energy and the Department of Defense (Office of Munitions) that facilitates the development of technologies of mutual interest to the two Departments. The cryocycling project is one of several that focus on demilitarization aspects of conventional weapons and weapon systems. During FY94 the project pursued the development of analytical and numerical models that can be used to describe and optimize the cryocycling process for preparing energetic materials for recycle and reuse. In addition, the demilitarization stockpile of the Department of Defense was analyzed to identify candidate munitions for the process, and pilot scale cryocycling operations were begun at an industrial contractor. When a material is cryocycled, it ...

Energy Technology Data Exchange (ETDEWEB)

Photodestruction has received much attention in recent years. In particular, titanium dioxide (TiO{sub 2}) and ozonolysis have attained a position of prominence. These technologies hold promise for the destruction of trace amounts of aqueous high explosives that are generated by load and pack operations, as well as demilitarization activities. Currently this water is treated by passing through a bed of activated carbon. The carbon is then steam regenerated and reused, thus creating a second waste stream which must be disposed of, or the carbon is burned directly. Recent trends in environmental regulation have shown that this may not be a viable option for process water remediation in the future. This talk will discuss efforts to employ alternate aqueous treatment techniques that not only remove the explosives compounds but are able to transform the parent compound into carbon dioxide and water. Titanium dioxide photocatalysis as well as ...

Science.gov (United States)

... Concerning Persons and Organizations not Affiliated with the Department of Defense," January 7, 1980 (f) DoD 5240.1-R, "Procedures Governing ...

International Nuclear Information System (INIS)

As an engineered barrier system in the geological disposal of high-level waste, multibarrier system is considered. Multibarrier system consists of the vitrified waste, the overpack and the buffer. Bentonite is one of the potential material as the buffer because of its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. As the construction technology of the buffer, the block installation method and in-situ compaction method, etc, are being investigated. The block installation method is to emplace the buffer blocks manufactured in advance at the ground facility, and construction processes of the block installation method at the underground will be simplified compared with the in-situ compaction method. However, the block joints of buffer might be a mechanical weak portion or might ...

Energy Technology Data Exchange (ETDEWEB)

For the purpose of digging up themes of the joint research which develop the R and D in the industrial technology field in Japan to a new stage, researchers were sent to the world representing research institutes to conduct the research survey of 'Nano-structured carbon and hydrogen absorption' and 'Development of the creation technology of nano-porous materials.' As to the former, an experiment on electrochemical hydrogen absorption of carbon materials including nanotubes was conducted by researchers dispatched, but the large absorption amount was not observed. As to the latter, visits were paid to Fraunhofer Institute and the related facilities in Germany, Princeton University, MIT, GIT and Naval Research Laboratories in the U.S., Orleans University in France, AO Research Institute (bone repair study) in Switzerland, Cambridge University and University of Bristol in the U.K., etc., and ...

Science.gov (United States)

... 3 Joint Committee on Atomic Energy as a Model . . . . . ... Joint Committee on Atomic Energy as a Model Page 8. CRS-4 ...

Energy Technology Data Exchange (ETDEWEB)

The document, based on European guidelines, was jointly developed by radiation oncologists, radiation physicists and radiation technologists. It contains the aims of the guidelines, professional profiles, roles and responsibilities, personnel and equipment requirements, procedures.

CERN Multimedia

Are you interested in beam dynamics? Do you work on the LHC injectors or CLIC or maybe feasibility studies fornew machines? Then this is for youJAS'2000: Joint CERN-Japan-JINR-Russia-US SchoolFrontiers of Accelerator Technology: High Quality Beams to be held on a river boat between St. Petersburg and Moscow 1 to 14 July 2000. For further information see eitherhttp://schools.web.cern.ch/Schools/CAS/ orhttp://www.indiana.edu/~uspas/programs/js/jas2000.html

Science.gov (United States)

... 4 Joint Committee on Atomic Energy as a Model . . . . . ... Joint Committee on Atomic Energy as a Model ...

International Nuclear Information System (INIS)

In this study, a range of joining technologies has been investigated for creating attachments between refractory metal and Ni-based superalloys. Refractory materials of interest include Mo-47%Re, T-111, and Ta-10%W. The Ni-based superalloys include Hastelloy X and MarM 247. During joining with conventional processes, these materials have potential for a range of solidification and intermetallic formation-related defects. For this study, three non-conventional joining technologies were evaluated. These included inertia welding, electro-spark deposition (ESD) welding, and magnetic pulse welding (MPW). The developed inertia welding practice closely paralleled that typically used for the refractory metals alloys. Metallographic investigations showed that forging during inertia welding occurred predominantly on the refractory metal side. It was also noted that at least some degree of forging on the Ni-based superalloy side of the ...

Energy Technology Data Exchange (ETDEWEB)

The Joint European Torus (JET) fusion machine is the only device capable of operation with tritium (as fuel) and Be (as plasma facing component), what makes it best suited to study ITER relevant issues. A large variety of activities are performed within the JET Fusion Technology Task Force. In this paper, some topics such as erosion/deposition and material transport, flakes characterization and detritiation techniques are highlighted. Recent results obtained using a pumping cryo-panel and on plasma facing component characterisation are given. Finally, issues that will be addressed in the forthcoming JET work-programme are presented, such as a beryllium main wall for JET and in-situ laser detritiation. (authors)

Energy Technology Data Exchange (ETDEWEB)

In its beginning, the U.S. Department of Energy (DOE) Office of Environmental Management (EM) viewed private industry as lacking adequate technology know-how to meet demands of hazardous and radioactive waste problems at the DOE`s laboratories and nuclear weapons production facilities. In November 1989, EM`s Office of Technology Development (recently renamed the Office of Science and Technology) embarked on a bold program of developing and demonstrating {open_quotes}innovative{close_quotes} waste cleanup technologies that would be safer, faster, more effective, and less expensive than the {open_quotes}baseline{close_quotes} commercial methods. This program has engaged DOE sites, national laboratories, and universities to produce preferred solutions to the problems of handling and treating DOE wastes. More recently, much of this work has shifted to joint efforts with private industry ...

Energy Technology Data Exchange (ETDEWEB)

Three companies--Amerada Hess Ltd., Shell Expro (a 50/50 joint partnership between Shell and Esso) and Texaco--have joined forces in a project that will combine their expertise. The Triton project will allow three fields (Bittern, Guillemot West and Gullemot Northwest) to be developed simultaneously using subsea technology, with the wellheads on the seafloor and 68 miles (110 km) of flowlines taking oil and gas produced from the fields to a central floating production storage and offloading (FPSO) vessel. These fields are located in the central area of the North Sea, about 118 miles from Aberdeen in 295 ft of water. The paper discusses the development of the fields, subsea technology, technical challenges, laying the pipeline, and project completion.

Energy Technology Data Exchange (ETDEWEB)

The Power Systems Development Facility (PSDF) is a joint Department of Energy/Industry sponsored engineering-scale facility for testing advanced coal-based power generation technologies. High temperature, high pressure gas cleaning is critical to many of these advanced technologies. Barrier filter elements that can operate continuously for nearly 9000 hours are required for a successful gas cleaning system for use in commercial power generation. Since late 1999, the Kellogg Brown & Root Transport reactor at the PSDF has been operated in gasification mode. This paper describes the test results for filter elements operating in the Siemens-Westinghouse particle collection device (PCD) with the Transport reactor in gasification mode. Operating conditions in the PCD have varied during gasification operation as described elsewhere in these proceedings (Martin et al, 2002).

Environmental Research Database

No further description is available

Energy Technology Data Exchange (ETDEWEB)

International Thermonuclear Experimental Reactor (ITER) project is the international collaboration one for the commercialization of nuclear fusion energy through the technical and engineering verification. In ITER project, we plan to procure the blanket systems which has the risk of technology and cost when it is newly developed. We are developing the manufacturing process and joining technology for the ITER blanket to complete the procurement with qualified blanket system. To evaluate the soundness of manufacturing process, specimen and mock-up tests are being prepared. Finally, we can obtain the key technology of nuclear fusion reactor especially on the blanket design, joining and manufacturing technology through the present project and these technologies will help the construction of Korea fusion DEMO reactor and the development of commercial nuclear fusion reactor in Korea. In ...

Science.gov (United States)

... CJCSI 3141.01C, Responsibilities for the Management and ... of a multivolume set of CJCS unclassified and ... (1) CJCSM 3122.01A, Joint Operation ...

Science.gov (United States)

... Admiral Olson mentions the requirement for a standing joint task force headquarters in USSOCOM in order to fulfill the command's charter as a ...

Science.gov (United States)

... THE STANDING JSOTF HEADQUARTERS IN A STANDING JOINT TASK FORCE HEADQUARTERS OR COMBATANT COMMAND ...

Energy Technology Data Exchange (ETDEWEB)

Badger (Cambridge, MA) and Mobil (Fairfax, VA) are ready to jointly license a new cumene technology that they say achieves higher yields and product purity than existing processes. The zeolite-based technology is scheduled to be introduced at next month's DeWitt Petrochemical Review in Houston. The Mobil/Badger technology aims to challenge the dominant position of UOP's (Des Plaines, IL) solid phosphoric acid (SPA) catalyst process - which accounts for 80%-90% of the world's cumene production. In addition, Monsanto/Kellogg's aluminum chloride-based technology has gained significant momentum since its introduction in the 1980s. And late last year, ABB Lummus Crest (Bloomfield, NJ) also began marketing a zeolite-based cumene technology. While all the technologies make cumene via the alkylation of benzene ...

Energy Technology Data Exchange (ETDEWEB)

A project on the title is a special study of TRC (Technology Research Center) Japan National Oil Corporation, which aims at developing a system collecting many data near well bottom while drilling. The project is a 3-year project from 1993 to 1995 succeeding to results of a project on real-time drilling control technology which was finished in fiscal 1992. This paper is a record in fiscal 1993. In 1993, the first year, TRC starts a joint study with relational enterprises aiming at utilizing an EM-MWD (electromagnetic-measurement while drilling) system practically. Based on the past fruit of the study, the EM-MWD system was applied to an highly inclined well or a horizontal well. A total system was constructed, which improved electromagnetic radiation transmission efficiency, and reliability, and workability. An electromagnetic radiation receiver system for an offshore drilling rig was developed. A well bottom tools of 6-3/4 ...

Energy Technology Data Exchange (ETDEWEB)

The EMS Energy Institute at The Pennsylvania State University (Penn State) has managed the Gas Storage Technology Consortium (GSTC) since its inception in 2003. The GSTC infrastructure provided a means to accomplish industry-driven research and development designed to enhance the operational flexibility and deliverability of the nation's gas storage system, and provide a cost-effective, safe, and reliable supply of natural gas to meet domestic demand. The GSTC received base funding from the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL) Oil & Natural Gas Supply Program. The GSTC base funds were highly leveraged with industry funding for individual projects. Since its inception, the GSTC has engaged 67 members. The GSTC membership base was diverse, coming from 19 states, the District of Columbia, and Canada. The membership was comprised of natural gas storage field operators, service ...

Energy Technology Data Exchange (ETDEWEB)

This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that involves the building of a joint biogas plant serving 60 farmers and industrial companies with an annual processing capacity of 45,000 tons. The plant is to produce biogas to be fed into the gas mains and will not only reduce nutrient loading in a region with an extensive livestock industry but also reduce carbon dioxide emissions by using the gas as a motor fuel. The importance of the project with respect to both the environment and energy policy-making is discussed and the costs involved are examined. Details are presented on the technology used and on the material flows involved. Figures are quoted on energy production. The various biogenic substrates used, such as food wastes, waste oils, cereal wastes and used mushroom substrates, are discussed, as is the use of the solid and liquid outputs of the digester in farming activities.

Energy Technology Data Exchange (ETDEWEB)

The costs of greenhouse gas emission-reductions vary among countries depending on emission levels, technologies used, past emission-reduction achievements, path of economic development, fuel mix, and initial endowment of hydrocarbon resources. The criterion of cost-effectiveness therefore suggests that the ways should be found to encourage emission reductions in the countries where the required costs of reduction of additional unit of emissions are the lowest. These countries usually face crucial capital constraints and have other development priorities than investing in reduction of greenhouse gas emissions. Developed countries could invest their resources in the former Soviet Union and the east European countries to achieve the same level of reduction of greenhouse gases with lower costs than they could in their own countries.

UK PubMed Central (United Kingdom)

Hyaluronan (HA) is important for joint cavitation, lubrication, volume regulation and synovial fluid drainage but little is known about the regulation of joint HA synthesis/secretion in vivo....Full Text Available

Science.gov (United States)

Special Operations Forces (SOF) within a Joint Task Force are controlled by a Joint Special Operations Task Force (JSOTF). Presently, JSOTF headquarters are formed around the core of the Theater Special Operations Command (TSOC), a service SOF headquarter...

Science.gov (United States)

Information superiority provides the Joint force a competitive ... Information Grid (GIG) as it matures and fills the needs of the Joint Task Force ... representatives from The Army Secretariat, Headquarters Department of Army ...

British Library Electronic Table of Contents (United Kingdom)

The addition of ?-Sialon nanoparticles to lubricants in heavy-duty frictional joints is shown to be effective.

Science.gov (United States)

... Chiefs of Staff, Joint Operation Planning and Execution System (JOPES) Volume I, Planning and Procedures, CJCSM 3122.01A (Washington, DC ...

International Nuclear Information System (INIS)

The general characteristics of radiation processing and its main applications of interest in Chile are described, with particular reference to the production of wood-plastic composites (WPC). The process itself and the technical characteristics of the resulting product are explained for products that demand an aesthetic appearance, warmth, toughness and durability, as in the flooring industry. Certain domestic wood products could receive a boost in quality by using this process, making them more competitive in demanding export markets. These products could open new markets, serving as substitutes, for example, for carpets and tiles. This would be highly convenient for Chile, considering the big supply of wood for industrial consumption that the country will have in the coming decade. Because of this situation two Chilean technology institutes, the Chilean Nuclear Energy Commission and INTEC-CHILE, are jointly working on a project that aims to ...

Energy Technology Data Exchange (ETDEWEB)

Activated charcoal has so far taken a shape of particle or powder, but as the third activated charcoal, fibrous activated charcoal (ACF) has begun to be produced industrially. In comparison with the conventional activated charcoal, ACF has such characteristics as follows (1) its rate of absorption and desorption is very fast, (2) its specific area is large and it has high absorption performance, (3) it has wide absorption characteristics, and (4) its reactivation and reutilization are possible. In addition, because of its fibrous condition, it can be processed into compound materials of various shapes by utilizing the fiber processing technology. Furthermore, it can be combined with other functional fibrous material and used as multifunctional material. In this article, the production process, performance, characteristics and usage of ACF, which is an excellent absorbent as stated above, are outlined with a focus on the pitch-based ACF developed ...

Energy Technology Data Exchange (ETDEWEB)

Certain innovative coke-oven repair techniques are reviewed that represent an engineered approach to a successful rehabilitation of all types of coke-oven batteries. These techniques have been developed during the last 10 years and experience gained on a number of repair projects has shown that these techniques operate as a cohesive and comprehensive method of end flue and through-wall repairs to gain additional years of operating life to coke-oven batteries. Extended operations approaching 10 to 15 additional years of service at lower costs than a pad-up rebuild and, while meeting the environmental emission regulations, are attainable using the techniques of: Proper tie-in joint preparation; Improved bricking up methodology; Preheating refractory during bricking up; Installation of spring-loaded bracing system; and installation of flexible coke-oven doors. Repair methods that do not incorporate the above techniques are subject to premature failure of the ...

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The design of a 345-kV prefabricated capacitive-graded joint for oil-filled cables and the manufacture and testing of prototype joints are described. Tests on prototype No. 4 demonstrated the adequacy of the printed circuit design. It was not possible to consistently obtain high-quality capacitive sheets and substantial effort is required to remedy this problem. Advantages of these prefabricated joints are summarized, and specific recommendations are made for further development of the concept.

Science.gov (United States)

Osteoarthritis

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper reports on a flexible dimensionaly flush joint for 500kV aluminum-sheathed oil-filled cables capable of being assembled, pulled an installed in a similar manner to cables at site which has been developed. This joint is intended for use at intermediate points on long bridges or tunnels where local assembly and installation of conventional joints would be difficult. In developing the joint various novel and original techniques have been employed, including the flexible flush jointing of segmental conductors, the flexible jointing of paper insulation by a combination of wrapping-back and stepping methods, plus on-site aluminum sheath corrugating and sealing methods.

International Nuclear Information System (INIS)

Full text of publication follows: As SiCf/SiC composites are very low activation materials, their use as structural material for the reactor blanket and first wall components appears essential to demonstrate the potential of D-T fusion power reactor. Positive features of SiCf/SiC are their high performances at elevated operating temperature and the ability to produce a specific component. Critical issues of SiCf/SiC are the mechanical properties, radiation stability and, with regard to technological issues, their hermeticity and joining processes. Improvement of joining processes for SiC/SiC components is also needed. Recently, several blanket designs have been studied: the TAURO blanket concept in the European Union, the ARIESAT concept in the US and the DREAM concept in Japan. In those reactors, hermetic SiCf/SiC or self-sealing coatings are mandatory. The basic idea of self sealing concept is to manufacture a coating with specific requirements (CTE and ...

International Nuclear Information System (INIS)

A radioactive Waste Incineration System (WIS) with suspension combustion is noticed as effective volume reduction technology of low level radiactive wastes that are increasing every year. In order to demonstrate the decontamination efficiency of ceramic filter used on WIS, this test has been carried out with the test facilities as joint research of Central Research Institute of Electric Power Industry (CRIEPI) and Sumitomo Heavy Industries, Ltd. Miscellaneous combustible waste and power resin, to which 5 nuclides (Mn-54, Fe-59, Co-60, Zn-65, Cs-137) were added, were used as samples for incineration. As the result of the test, it was verified that Decontamination Factor (DF) of the single stage ceramic filter was usually kept over 10"5 for every nuclide, and from the results of above DF, over 10"8 is expected for real commercial plant as a total system. Therefore, it is realized that the off-gas clean up system of the WIS composed of only single ...

International Nuclear Information System (INIS)

The Advanced CANDU Reactor (ACR"T"M) is the 'Next Generation' CANDU"R reactor, aimed at safe, reliable power production at a capital cost significantly less than that of current reactors such as the very successful CANDU 6 reactors (e.g., Wolsong 1-4). The Wolsong 1-4 units are being joined by the Qinshan Phase 3 units in China as the current successful examples of CANDU technology. The ACR design builds on this knowledge base, adding a selected group of innovations to obtain substantial cost reduction while retaining a proven design basis. The ACR maximizes the use of components and equipment applications that are well proven through CANDU and other nuclear experience. Joint development of equipment designs and specifications with manufactures has been emphasized. Similarly, the ACR design emphasizes constructability, and takes advantage of inherent CANDU features to enable short project and construction schedules. Overall, the ACR design ...

International Nuclear Information System (INIS)

The Fact Finding Committee on 'Future Nuclear Power Policy' established by the 8th German Federal Parliament in its report of June 1980 among other items published the recommendation to commission a 'risk oriented analysis' of the SNR-300 in order to enable a pragmatic comparison to be made of the safety of the German prototype fast breeder reactor and a modern light water reactor (a Biblis B PWR). The Federal Minister for Research and Technology in August 1981 officially commissioned the Gesellschaft fuer Reaktorsicherheit (GRS) to conduct the study. Following a recommendation by the Fact Finding Committee, additional studies were performed also by a group of opponents of the breeder reactor. On the instigation of the group of opponents the delivery date of the study was altered several times and finally set at April 30, 1982. GRS submitted its report by this deadline. However, a joint report by the two groups could not be compiled, as had ...

Energy Technology Data Exchange (ETDEWEB)

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarily at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report covers the reporting period 1 April to 30 June 2003 in which PSI, Aquasearch and University of Hawaii conducted their tasks. Based ...

Energy Technology Data Exchange (ETDEWEB)

Universal Oil Products, Inc. (UOP) of Des Plaines, Illinois has contracted A.E. Roberts & Associates, Inc. (AERA) of Atlanta, Georgia to prepare a sensitivity analysis for the development of the Fluidized-bed Copper Oxide (FBCO) process. As proposed by AERA in September 1991, development of the FBCO process design for a 500 mega-watt (MW) unit was divided into three tasks: (1) Establishment of a Conceptual Design, (2) Conceptual Design, (3) Cost Analysis Task 1 determined the basis for a conceptual design for the 500 megawatt (MW) FBCO process. It was completed by AERA in September of 1992, and a report was submitted at that time {open_quotes}Establishment of the Design Basis for Application to a 500 MW Coal-fired Facility.{close_quotes} Task 2 gathered all pertinent data available to date and reviewed its applicability to the 500 MW FBCO process. Work on this task was carried out on a joint basis by the AERA team members: Roberts & Schaefers worked on the ...

Energy Technology Data Exchange (ETDEWEB)

Cooperative procurement is a variation of public purchasing which may be used as an instrument to transform the market and stimulate innovation enhancing environmental performance. The core of the procedure is the following: Coordinated by a central agency a group of buyers - public administrations, but also private companies, associations, etc. - gets together and jointly formulates a catalogue of performance requirements for a specific product truly suiting their preferences. This catalogue may contain (combinations of) requirements not yet available on the market and includes energy efficiency and/or environmental performance among other preferences important to the users. On the basis of the product requirements the buyer group launches a call for tenders, evaluates the bids received from the manufacturers and commits to buying the winning product. Thus, a market is provided for the most successful innovators in a given area of technology. ...

British Library Electronic Table of Contents (United Kingdom)

This experimental study investigates the effectiveness of crossed inclined bars (X-bars) as joint shear reinforcement in exterior reinforced concrete beam-column connections under cyclic deformations. Test results of 20 joint subassemblages with various reinforcement ratios and arrangements including X-bars in the joint area are presented. The X-type, non-conventional reinforcement is examined as the only joint reinforcement and in combination with common stirrups or vertical bars. The experimental results reported herein include full loading cycle curves, energy dissipation values and a categorization of the observed damage modes. Based on the comparisons between the overall hysteretic responses of the tested specimens, it is deduced that joints with X-bars exhibited enhanced cyclic perfo...

International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

UK PubMed Central (United Kingdom)

Objectives To test the hypotheses that, compared with conventional outpatient consultations, joint teleconsultation (virtual outreach) would incur no increased costs to the NHS, reduce...Full Text Available

UK PubMed Central (United Kingdom)

The Joint Commission on Accreditation of Hospitals (JCAH) has continuously emphasized improvement in the quality of care provided in hospitals as the central purpose of the accreditation process. In...Full Text Available

Science.gov (United States)

The purpose of the Joint Task Force Headquarters Master Training Guide (JTF HQ MTG) is to provide a descriptive, performance-oriented training guide to assist leaders in training their units. It also serves as a guide for the JTF Headquarters in actual op...

UK PubMed Central (United Kingdom)

Objective:To assess the efficacy of facet joint infiltrations for pain relief in 44 selected patients with chronic nonradicular low back pain (LBP).Materials...Full Text Available

Science.gov (United States)

Telecommunication Union IVDT integrated voice data terminal IXC interexchange carrier JANAP Joint Army-Navy-Air Force Publication(s) JCS Joint Chiefs of Staff JPL Jet Propulsion...

UK PubMed Central (United Kingdom)

This joint statement was developed by the CMA and the Canadian Pharmaceutical Association, a national association of pharmacists, and includes the goal of drug therapy, strategies for collaboration...Full Text Available

Science.gov (United States)

...COMCAM forces document Air Force and air component activities...supported unified command or joint task force commander, through the...Force COMCAM forces in a joint environment. If an...share of Unified Command headquarters COMCAM and visual...

Science.gov (United States)

PMID:17710912

Science.gov (United States)

... The pharmacologist/toxicologist and the statistician will jointly determine if a statistical review is needed and when the review should be done. ...

Science.gov (United States)

... from theory to practice will be significantly reduced while intrinsically revolutionizing the approach to engineering network security architectures. ...

Science.gov (United States)

... By comparing the behavior of individuals tackling the missionaries and cannibals problem to pairs of people solving this problem, we have been ...

Science.gov (United States)

... US Congress, Joint Committee on Atomic Energy, Development, Use, and Control ofNuclear Energy for the Common Defense and Security and for ...

International Nuclear Information System (INIS)

Published in summary form only.

Science.gov (United States)

The congressional Joint Committee on Atomic Energy issued the panel report Transportation of Radioactive Material by Passenger Aircraft. ...

CERN Document Server

Materials science and technology

CERN Document Server

Handbook on information technology in finance

Energy Technology Data Exchange (ETDEWEB)

The production of heavy crude oils increased in the last years in the world. Crude oils with high density, viscosity, acidity and sulfur, nitrogen, metals and asphaltenes contents, by the others hand, low stability and low product quality. The challenger of many refiners is find solutions to refine the heavy crude oils, and produce fuels with certify quality, such as Jet Fuel. The principal aviation technique on the world work with gas turbines engines feted for jet fuel (JET A1). The quality specifications of this fuel are establish by International Norms: ASTM-1655, DEF STAN 91-91-3 (DERD 2494) and joint Fuelling System Check List. The world technologies to obtain jet fuel from mixtures of heavy crude oil with middle crude oils are: Atmospheric distillation, with a posterior hydrogenation and finally the additivation. Studies carried out have demonstrates that the Cubans heavy crude oils is characterized for having API less than 10, raised ...

Energy Technology Data Exchange (ETDEWEB)

A Lurgi baseline study was requested by the DOE/GRI Operating Committee of the Joint Coal Gasification Program for the purpose of updating the economics of earlier Lurgi coal gasification plant studies for the production of substitute natural gas (SNG) based on commercially advanced technologies. The current study incorporates the recent experience with large size Lurgi plants in an effort to improve capital and operating costs of earlier plant designs. The present coal gasification study is based on a mine mouth plant producing 250 billion Btu (HHV) per day of SNG using the Lurgi dry bottom coal gasification technology. A Western subbituminous coal was designated as the plant food, obtained from the Rosebud seam at Colstrip, Montana. This study presents the detailed description of an integrated facility which utilizes coal, air, and water to produce 250 billion Btu (HHV) per day of SNG. The plant consists of coal handling ...

International Nuclear Information System (INIS)

Radiation technology offers a very wide scope for utilisation and commercial exploitation in various field. All over the world, this technology is being favourably considered for different applications like radiation sterilisation of medical products, preservation of food by controlling the physiological processes for extending shelf-life and eradication of microbial and insect pests, radiation processing of polymeric materials and treatment of sewage sludge. Bangladesh Atomic Energy Commission has taken radiation processing programmes in a big way right from its inception. This paper describes the studies carried out by various research groups in Bangladesh Atomic Energy Commission mainly using Cobalt-60 gamma radiation. The investigation covers medical sterilisation, food preservation and development and modification of polymeric materials by gamma radiation. Both food preservation and radiation sterilisation of medical products are now being ...

Wastenet

Technology Strategy Board Driving Innovation ...Technology Strategy 2009-2012 ... The vision of the Technology Strategy Board is for the UK to be a global leader in innovation

International Nuclear Information System (INIS)

Authors obtained T1-weighted MRI images of the femoral head after fracture of the femoral neck and classified the signals into four patterns to investigate the sequential changes of the femoral head. The T1-weighted MRI images obtained initially after femoral neck fracture showed a normal pattern in 10 of the 15 hip joints studied. MRI images obtained subsequently still showed the normal signal pattern in eight of the 10 hip joints which had shown the normal pattern in the first MRI, while two of the 10 joints subsequently showed a band pattern. The joint with the homogeneous pattern in the first MRI subsequently showed a band pattern. Of the three joints with an inhomogeneous pattern in the first MRI, two joints showed a subsequent band pattern, and the other a normal pattern. The joints which showed a band pattern continued to show a ...

Science.gov (United States)

Page 1. TRANSITIONING DARPA TECHNOLOGY ... Transitioning DARPA Technology JAMESJ.RJCHARDSON DIANE L. LARRNA ...

Energy Technology Data Exchange (ETDEWEB)

Within its competence for energy research, the Bundesministerium fuer Wirtschaft und Arbeit (BMWA) (Federal Ministry of Economics and Technology) sponsors investigations into the safety of nuclear power plants. The objective of these investigations is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order to the BMWi, continuously issues information on the status of such investigations by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual ...

International Nuclear Information System (INIS)

The mixed structure of a nuclear reactor building is composed of SC-columns, S-beams, S-joints and PCa-panels. Following the last report (Part 7)[1], the main test results of the mixed structure, that is, the deformation mode, strain distribution and shear strength, are described. The S-joints using ultrahigh strength materials had no buckling nor shear slipping. The proposed mixed structure resisted the external horizontal forces under integrated uniformity among SC-columns, S-joints and PCa-panels. It could be confirmed that the mixed structure can be established. (author)

International Nuclear Information System (INIS)

Studied are the mechanical properties of welded joints and heat affected zones of the Kh8N10T steel and OT4 and VT1-2 titanium alloys on welding in Ar+deltaF_6 and Ar+CCl_2F_2 mixtures contributed to a decrease of porosity. Tensile and impact tests of welded joints have revealed that additions of sulfur hexafluoride into argon causes a decrease of impact strength in titanium alloy when the tensile strength does not depend on the composition of a halogen-containing atmosphere. Freon (CCl_2F_2) additions decrease only slightly the impact strength of the investigated alloys.

Science.gov (United States)

Subcommittee of the Joint Committee on Atomic Energy of the United States, Outer Space Propulsion by Nuclear Energy, hearings, 85th Cong., 2d sess., 22, ...

Science.gov (United States)

... 3122.01A, Joint Operation Planning and Execution System (JOPES) Volume I, Planning Policies and Procedures (Sept. 29, 2006) and CJCSM ...

Science.gov (United States)

Joint Committee on Atomic Energy. Comgress of the United States. Washington, D. C.. 1 - Chief, Life Sciences Division. A m y Research Office ...

Science.gov (United States)

... Headquarters Element, Defense Logistics Agency, Support Detachment 3 ... Joint Task Force, Team 6 ... 19th Special Forces Group, Support Element 1 ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... 7th Joint Task Force Augmentation Team Schwetzingen ... Headquarters 85th Division Training Support, Detach 2 ... 20th Special Forces Company A ...

Science.gov (United States)

... Third World Arms Proliferation and Forced Entry Operations: Circumstances Demanding the Creation of a Standing Joint Task Force Headquarters. ...

Science.gov (United States)

... Prior to 1977, one group, the Joint Committee on Atomic Energy, had oversight. Since 1977, this responsibility has been ...

Science.gov (United States)

... Joint Publication (JP) 5-0 (Washington DC: CJCS, 29 September ... and Execution System (JOPES) Volume 1. CJCSM 3122.01A (Washington, DC: 6 ...

Science.gov (United States)

... Joint Publication (JP) 5 (Washington, DC: CJCS, 26 December 2006 ... Policies and Procedures, (Washington, DC: CJCSM, 3122.01A 29 September ...

Science.gov (United States)

This paper summarizes the main features of four current REDD proposals: Compensated Reduction, Papua New Guinea et al; Joint Research Center; and Brazil. ... ...

Science.gov (United States)

... Joint Staff and other US Military (ie, Army, Navy, Air ... HEART RATE, AND BODY TEMPERATURE DURING WORK IN MAN, DOG, AND SWINE. ...

Science.gov (United States)

... WHS- Washington Headquarters Service ... but also with respect to other Joint, National and ... unit of action (UA) combat team or task force is organized ...

Science.gov (United States)

... established in allied communications publications (ACP); DISA circulars (DISAC), Joint Army-Navy-Air Force publications (JANAP), and MAJ- COM ...

Science.gov (United States)

... In this manner, a JBI-enabled COI would have the full suite of JBI information management capabilities, but would still be based on and have full ...

Science.gov (United States)

... Joint Staff and other US Military (ie, Army, Navy, Air ... The major products of this work are significant advances in ... Keywords: Dogs; Laboratory animals ...

DEFF Research Database (Denmark)

OBJECTIVE: To evaluate the interobserver agreement of ultrasonographic assessment of finger and toe joints in patients with rheumatoid arthritis (RA) by 2 investigators with different medical backgrounds. METHODS: Ultrasonography and clinical examination were performed on 150 small joints of 30 patients with active RA. A General Electric LOGIQ 500 ultrasound unit with a 7-13-MHz linear array transducer was used. In each patient, 5 preselected small joints (second and third metacarpophalangeal, second proximal interphalangeal, first and second metatarsophalangeal) were examined independently on the same day by 2 ultrasound investigators (an experienced musculoskeletal radiologist and a rheumatologist with limited ultrasound training). Joint effusion, synovial thickening, bone erosions, and power Doppler signal were evaluated in accordance with an introduced 4-grade semiquantitative scoring system, on ...

Science.gov (United States)

... Experts ( Appendix 5 ), and the NMFS-Sea Grant Joint Graduate Fellowship Program ( Appendix 6) . The Task Force consisted of one representative from NMFS Headquarters and 1-2 rep...

Science.gov (United States)

9-foot 9-inch blocks of concrete with asphaltic-filled expansion joints. The concrete was placed on 4 to 6 inches of gravel or #4 stone. ...

Science.gov (United States)

... WHS- Washington Headquarters Service. ... The standing Joint Task Force concept should be used more to provide warfighter forces and ...

Science.gov (United States)

... the USCINCPAC staff and the staff of the commander, US Seventh Fleet, as a designated Pacific Command Joint Task Force Headquarters, in crisis ...

Science.gov (United States)

... Page 25. US Department of Defense, Joint Operation Planning and Execution System, Vol 1, Planning Policies and Procedures (CJCSM 3122.01A). ...

Science.gov (United States)

Feb 6, 2003 ... Director, Plans and Programs, Headquarters Air Force Materiel Command, .... Commander of the Joint Task Force Southwest Asia at Prince ...

Science.gov (United States)

... (l0)6o). 316. Statf,'ent. In Hearings before the Subcommittee on Research, Do'v,-Iopment, and Radiation of the Joint Committee on Atomic Energy. ...

Science.gov (United States)

joint task force (JTF), division (OIV) and regimental combat team (RCT) with ..... Headquarters, Department of the Army. (HQOA), (2010). Field Manual 2-0 ...

Energy Technology Data Exchange (ETDEWEB)

ENEA (Italian National Agency for New Technologies, Energy and the Environment) is conducting a large research and development programme on innovative vehicles with high energy efficiency and low environmental impact. In particular conducts activities on electric and hybrid vehicles. Testing and evaluation activities play a strong role in this programme. A complete characterization chain has been then defined and set up with a network of facilities which covers main testing needs for single components, subsystems and complete vehicles, in simulated and real operating conditions. The test facility which has been realised is able to experiment and fully characterise complete drive-trains (and subsystems) for pure electric and hybrid vehicles. It is composed by a different section for each subsystem: 1) power generation; 2) energy storage and management; 3) driving motors. Each section acts as an experimental island, able to operate alone or ...

Energy Technology Data Exchange (ETDEWEB)

Lawrence Livermore, Sandia Livermore and Los Alamos National Laboratories have a joint project to develop an optimized hydrogen fueled engine for series hybrid automobiles. The major divisions of responsibility are: system analysis, engine design and kinetics modeling by LLNL; performance and emission testing, and friction reduction by SNL; computational fluid mechanics and combustion modeling by LANL. This project is a component of the Department of Energy, Office of Utility Technology, National Hydrogen Program. We report here on the progress on system analysis and preliminary engine testing. We have done system studies of series hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. The impact of various on-board storage options on fuel economy are evaluated. Experiments with an ...

Energy Technology Data Exchange (ETDEWEB)

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarily at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report covers the reporting period 1 January to 31 March 2004 in which PSI, Aquasearch and University of Hawaii conducted their tasks. ...

Energy Technology Data Exchange (ETDEWEB)

In Chapter 2 the evaluation methods of input ground motions for seismic design are summarized and especially the empirical and/or stochastic Green's function method is introduced in order to calculate the broadband strong motions based on the physically reliable fault model. Then the evaluation procedure is applied to the Ulsan fault system near which Wolsung nuclear power plant is located. In chapter3, the PSHA case studies for Wolsung NPP site are performed, in which multi attenuation equations of earthquake motions are adopted. Moreover, the results of seismic hazard evaluation for eight sites in Korea are shown. In addition, the contents of two literatures on seismic hazard evaluation are introduced. In chapter 4, isolation devices for emergency diesel generator have been studied. The models for friction-pendulum system, high damping rubber bearing and natural rubber bearing are developed and implemented in the TDAP-III. Then, the rubber bearings as the isolation system ...

Energy Technology Data Exchange (ETDEWEB)

Several recent improved methods for the EGFM are introduced in order to avoid artificial holes seen in the synthetic acceleration spectrum. Furthermore evaluation of input ground motions at Wolsung NPP are performed by varying the source parameters that may control the high-frequency wave radiation and the deviation of the synthetic motions are revealed. The PSHA case studies for four NPP sites (Wolsung, Kori, Uljin, Younggwang) are performed. In the analysis, site-specific attenuation equations developed for Korean NPP sites are employed, and the seismic hazards for the target sites are evaluated in the case where the four kind of seismic source models are considered. Moreover, the PSHA for Wolsung and Younggwang are conducted by using the site-specific attenuation equation with the index of response spectra and the uniform hazard spectra are evaluated for the two sites. The supporting tool for seismic response analysis and the evaluation tool for evaluating annual probability of ...

International Nuclear Information System (INIS)

The excess of US electrical generating capacity which has existed for the past 15 years is coming to an end as we enter the 1990s. Environmental and energy security issues associated with fossil fuels are kindling renewed interest in the nuclear option. The importance of these issues are underscored by the National Energy Strategy (NES) which calls for actions which open-quotes are designed to ensure that the nuclear power option is available to utilities.close quotes Utilities, utility associations, and nuclear suppliers, under the leadership of the Nuclear Power Oversight Committee (NPOC), have jointly developed a 14-point strategic plan aimed at establishing a predictable regulatory environment, standardized and pre-licensed Advanced Light Water Reactor (ALWR) nuclear plants, resolving the long-term waste management issue, and other open-quotes enabling conditions.close quotes GE is participating in this national effort and GE's family of advanced nuclear power ...

Energy Technology Data Exchange (ETDEWEB)

This is the third quarterly progress report for Year 3 of the ACTS Project. It includes a review of progress made in: (1) Flow Loop construction and development and (2) research tasks during the period of time between Jan. 1, 2002 and Mar. 31, 2002. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 3: Addition of a Cuttings Injection/Separation System), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 9b): ''Study of Foam Flow Behavior Under EPET Conditions'', (d) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (e) Research on three instrumentation tasks to measure: Cuttings ...

Science.gov (United States)

... Information Technology (IT) Management: ... The role of information technology figures prominently in the Homeland Security Act of 2002. ...

Science.gov (United States)

This is Japan Report with Science and Technology. It contains the issues with different topics on biotecnology, defense industry, nuclear engineering, Marine technology, science and technology policy.

Science.gov (United States)

Information Technology Research for National Priorities (ITR) Fiscal Year 2004 Announcement ... the Information Technology Research (ITR) Program is focusing on Information Technology Research in ...

Indian Academy of Sciences (India)

- technology moving forward with new developments ...

Science.gov (United States)

Resistance exercise has been widely reported to have positive rehabilitation effects for patients with neuromuscular and orthopaedic conditions. This paper presents an optimal design of magneto-rheological fluid dampers for variable resistance exercise devices. Adaptive controls for regulating the resistive force or torque of the device as well as the joint motion are presented. The device provides both isometric and isokinetic strength training for various human joints.

International Nuclear Information System (INIS)

In recent years there has been a renewed interest in the treatment of quantum mechanics in terms of joint distribution functions, i.e. functions of momentum and position coordinates p and q. The author considers j.d.f. in the sense of classical probability theory of a stochastic variable. The j.d.f. is then interpreted as the probability that the variables p and q have certain values, the variables being considered as a property possessed by the object system. This formalism is used to provide a unified description of bradyons and tachyons. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

To evaluate injury patterns of facet joints and associated soft tissue injuries in patients with acute traumatic cervical facet joint injuries. From among patients with cervical spine trauma, 27 with facet joint injuries, as seen on CT and MRI, were chosen for this study. CT scans were analyzed with regard to the location of facet joint injury, the presence or absence of facet dislocation or fracture, and other associated fractures. MR images were analyzed with regard to ligament injury, intervertebral disc injury, intervertebral disc herniation, and spinal cord injury. The most common location of facet joint injury was C6-7 level(n=10), followed by C5-6(n=8). Among these 27 patients with facet joint injuries, 12(44%) had bilateral injuries and 15(56%) unilateral injuries. Facet fractures were present in 17 cases(63%) and the fracture of inferior facet was more ...

International Nuclear Information System (INIS)

Recently, weight reduction of vehicles has been of great interest, and consequently, the use of low-density materials in the automotive industry is increasing every year. Materials should not be substituted such a way that material of component parts is simply changed because there is a problem in achieving stiffness and strength. To achieve these requirements, the automobile should be redesigned totally. Aluminum spaceframe is rapidly being adopted as a body structure for accommodating lightness, stiffness and strength requirement. In aluminum spaceframe manufacturing, it is often required to join aluminum tube. But there are few suitable methods for joining aluminum tube, so that much interest has been focused on testing suitable joining methods. Joining by electromagnetic forming(EMF) can be useful method in joining aluminum tube, which offers some advantages compared with the conventional joining method. In this paper, joining by EMF was investigated as a pre-study for applying an ...

International Nuclear Information System (INIS)

To investigate the effect of external loads arising from differential thermal expansion between a substrate and a surface-mount component during thermomechanical cycling, specimens with a nickel surface-mount component on a copper substrate were prepared. Specimens consisted of two 100 #mu#m thick 1 mm"2 solder joints about 9 mm apart, with two designs. In one specimen (denoted 'dual-shear'), the as-fabricated joints were not stressed due to differential contraction during solidification and cool down. In the other specimen (denoted 'component'), a continuous copper substrate between the joints caused the nickel component to be put in compression during cool down, which imposed shear on the joints. To impose differential thermal shear strains, the 'dual-shear' specimen was clamped to a copper block to cause a significant reversal in sign of the shear imposed on the solder joint ...

International Science & Technology Center (ISTC)

Development of Experimental Large-scale Technology and Creation of Technological Line of Rubomicine Production

CERN Document Server

Information technology and the productivity paradox

Energy Technology Data Exchange (ETDEWEB)

A discussion is presented of the chemistry and technology of coal liquefaction and the physics and technology of coal desulfurization. 31 refs.

Energy Technology Data Exchange (ETDEWEB)

On June 2, 1992, Landers` earthquake struck the Solar Electric Generating System II, located in Daggett, California. The 30 megawatt power station, operated by the Daggett Leasing Corporation (DLC), suffered substantial damage due to structural failures in the solar farm. These failures consisted of the separation of sliding joints supporting a distribution of parabolic glass mirrors. At separation, the mirrors fell to the ground and broke. It was the desire of the DLC and the Solar Thermal Design Assistance Center (STDAC) of Sandia National Laboratories (SNL) and to redesign these joints so that, in the event of future quakes, costly breakage will be avoided. To accomplish this task, drawings of collector components were developed by the STDAC, from which a detailed finite element computer model of a solar collector was produced. This nonlinear dynamic model, which consisted of over 8,560 degrees of freedom, underwent model reduction to form a ...

International Nuclear Information System (INIS)

Magnetic resonance imaging has proven an invaluable method in the diagnosis of joint diseases associated with osteonecrotic, inflammatory, traumatic and degenerative processes. At the clinical level, it has an important role in decisions about the method of treatment and evaluations of the therapeutic success. When the merits of MRT are balanced against those of conventional radiography including tomography and CT, which both ensure better spatial resolution in the visualisation of cortical and spongy bone structures, it becomes quite evident that MRT must not be regarded as an alternative method of imaging but as one that can be used additionally to obtain the most information for the diagnosis of arthropathy. The question as to whether new pulse sequences (snap shots) or invasive techniques like intra-articular injection of paramagnetic substances (MR arthrography) are likely to become routine procedures in the detection of joint diseases ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, for an acceleration of utilization of magnesium alloy which is being interested in recent years, friction welding of AZ31 magnesium alloy was carried out, and the joint performance was discussed in relation to the deformation heat input in the upset stage and upset loss as a evaluation factor. Where, the deformation heat input in the upset stage is mechanical work represented by the product of upset speed and axial pressure. As a result, it was made clear that the friction welding of AZ31 magnesium alloy was easy in the atmosphere, and good welded joints without a non- adhesion area at the weld interface could de obtained. Moreover, the evaluation factors discussed were possible to evaluate to joint performance. (orig.)

International Nuclear Information System (INIS)

The VNC2 and VNC5 steel tests on endurance were carried out in order to determine the capacity for work of large welded samples and to investigate the methods of welding. The samples made by the arc welding demonstrated the most high endurance at low frequencies of loading during the test of welded joints made of the VNC2 steel. The application of the VNC2 steel interlayers together with intermediate heat treatment allows one to increase the static and fatigue strength of welded joints at corresponding decrease of the construction weight during welding of the VNC5 steel as well as its combination with the VNC2 steels. The gas protection deterioration during steel welding leads to considerable diversity of values of endurance.

Energy Technology Data Exchange (ETDEWEB)

Considering beryllium as plasma facing armour this paper presents recent results obtained in Russia. A special process of joining beryllium to a Cu-alloy material structure is described and recent results of thermal cycling tests of such joints are presented. Summarizing the results, the authors show that a Cu-alloy heat sink structure armoured with beryllium can survive high heat fluxes ({>=}10 MW/m{sup 2}) during 1000 heating/cooling cycles without serious damage to the armour material and its joint. The principal feasibility of thermal cycling of beryllium grades and their joints directly in the core of a nuclear reactor is demonstrated and the main results of this test are presented. The paper also describes the thermal cycling of different beryllium grades having cracks initiated by previously applied high heat loads simulating plasma disruptions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

When the use of retarders in utility vehicles increased in the middle of the 80s, the Forschungsvereinigung Automobiltechnik (FAT) commissioned a study on the safety aspect of this braking technology in trucks. Retarders are wear-free permanent brakes that are fitted in the drive transmission system of utility vehicles, thereby generating braking forces only at the wheels of the live shaft. The question of the possible overbraking of the live shafts was just as well investigated as the interaction between the retarder and service brake in so-called integrated braking systems, and both under conditions of low adhesion as well as in the border area of the dynamics of vehicle movement. This subject met with considerable joint interest on the part of the motor vehicle industry as well as of manufacturers of towed vehicles and unit sets. FAT, therefore, commissioned the Institut fuer Kraftfahrwesen of the University of Hannover to carry out a ...

Science.gov (United States)

... Headquarters 5th Brugade 78th Division (Ts) ... 2nd Battalion 20th Special Forces Company B ... 29th Corps Personnel Serves Hq Joint Task Force Aug ...

UK PubMed Central (United Kingdom)

Isokinetic training and assessment of the knee joint has been the mainstay of rehabilitation, especially in patients with anterior cruciate ligament deficiency. Besides the original shin pad used, the...Full Text Available

Science.gov (United States)

Washington, DC -07/24/09 Photo: Secretary Clinton and Iraqi Prime Minister al-Maliki at HCC Bilateral; Washington, DC -07/24/09 Photo: Secretary Clinton at Joint Press...

Energy Technology Data Exchange (ETDEWEB)

The corrosion behaviour of friction stir welded (FSW) joints of AA 5083 has been compared to that of MIG welded joints. Pitting and stress corrosion cracking (SCC) resistance in 3.5% NaCl + 0.3 g/l H{sub 2}O{sub 2} and in EXCO (4 M KCl + 0.5 M KNO{sub 3} + 0.1 M HNO{sub 3}) solutions has been determined at 25 C. SCC susceptibility was evaluated by slow strain rate tests (SSRT), at a strain rate of 1 x 10{sup -6}s{sup -1}. Welds obtained by FSW technique showed a higher corrosion resistance in EXCO solution and a lower pitting tendency than the base alloy. Electrochemical measurements (corrosion potential measurements, polarization curves recording) evidenced that FSW weld was cathodic to base alloy. FSW joints were not susceptible to SCC in both test solutions, whereas MIG joints cracked in both solutions. (orig.)

Science.gov (United States)

This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development ...

Science.gov (United States)

Climate Observations Joint Air-Sea Monsoon Investigation: JASMINE Nauru '99 NTAS PACS SHEBA STRATUS VOCALS WHOTS Data Cruises Tropical Eastern Pacific Synthesis The Research...

International Nuclear Information System (INIS)

Metallic O-ring or Helicoflex seals can prevent relaxation and provide greater resilience than composite seals, helping to keep joints leaktight. Their characteristics and applications in the nuclear industry are outlined. (Author).

Wastenet

... The high resolution imagery , collected over Rio de Janeiro, Brazil, included a mixture of large commercial buildings and private houses, as well as the airport and some community parks. 10/08/11 Read more Top EU R&D companies expect a 5% ...

UK PubMed Central (United Kingdom)

Cytokine regulation of synovial fluid (SF) lubricants, hyaluronan (HA), and proteoglycan 4 (PRG4) is important in health, injury, and disease of synovial joints, and may also provide powerful regulation...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In view of the situation that aging of boiler components proceeds and some `Type IV` cracking incidents are reported recently, the development of an accurate remaining life evaluation method for boiler weldment parts is an important subject for the utilities. In this study, simulated materials with coarse and fine grain microstructures in a weldment heat affected zone were produced, and their high temperature strength properties were evaluated. The strength property of the weld joint was also discussed based on the experimental and analytical results. It was found that the creep rupture strength of the fine grain material was as low as 1/2 of the base metal and as 1/5 of the coarse grain material, and the weld joint ruptured at the fine grain region in a shorter period than the base metal as the applied stress level decreased. Many grainboundary creep cavities were also observed in the fine grain region. A creep deformation analysis by FEM ...

Science.gov (United States)

... Volume(s) Volume(s) II Item Identification 1,2,3,4, JANAP Joint Army-Navy- 2,7 5,6,13 Air Force JIM Item Intelligence 2 Publication Maintenance ...

International Nuclear Information System (INIS)

May 2010 p. 81-84 Japan Ishizawa, Makoto JFE Steel Corporation, Tokyo

UK PubMed Central (United Kingdom)

Prophylactic knee braces are designed to prevent and reduce the severity of ligamentous injuries to the knee. Conflicting evidence is reported concerning their efficacy. The purpose of this study was...Full Text Available

Science.gov (United States)

... 2 Joint Pub. 5-0 (Dec. 26, 2006); CJCSM 3122.01A (Sept. 29, 2006, current as of Oct. 11, 2008); and CJCSM 3122.03C (Aug. 17, 2007). Page 31. ...

Science.gov (United States)

This study investigates the doctrinal guidance available to a corps headquarters if required to serve as ajoint task force headquarters and simultaneously be required to warfight the corps. The study contends that a corps being required to simultaneously ...

Science.gov (United States)

...undertake missions and tasks (on either a...Secretary of Defense to task the DoD Components...the Chairman of the Joint Chiefs of Staff any commitment of military forces assigned to the Unified... (9) Military forces employed in MSCA...approval from higher headquarters, local military...

Science.gov (United States)

and Renewable Energy EERE Home | Programs & Offices | Consumer Information Geothermal Technologies Program Search Search Help Geothermal Technologies Program HOME ABOUT...

Science.gov (United States)

and Renewable Energy EERE Home | Programs & Offices | Consumer Information Geothermal Technologies Program Search Search Help Geothermal Technologies Program HOME ABOUT...

Science.gov (United States)

The results of an investigation into the behavior of adhesively bonded doubler splices of two composite material sandwich panels are presented. The splices are studied from three approaches: analytical; numerical (finite elements); and experimental. Several parameters that characterize the splice are developed to determine their influence upon joint strength. These parameters are: doubler overlap length; core stiffness; laminate bending stiffness; the size of the gap between the spliced sandwich panels; and room and elevated temperatures. Similarities and contrasts between these splices and the physically similar single and double lap joints are discussed. The results of this investigation suggest several possible approaches to improving the strength of the sandwich splices.

British Library Electronic Table of Contents (United Kingdom)

In the last 40 years, significant advances have been made in the understanding of the neurophysiologic processes involved in the experience of trauma and pain. This knowledge, together with the rapid growth and understanding in the behavioral health sciences, has expanded to include a much better appreciation of how these fields are converging and contribute to a process called neuroplasticity. These basic mechanisms common to all patients have important implications for clinical outcome and for improving clinical practice. This article is written for clinicians who manage patients with sacroiliac joint dysfunction, a specific type of nonspecific low back pain.

Energy Technology Data Exchange (ETDEWEB)

The activities and results of a Small Business Innovation Research Phase II project entitled ''Rapid Tools for Joint Inversion and Imaging'' are presented. Research and development on three-dimensional methods to recover distributions of material property values from sparse data are reported. Innovations using artificial neural networks and extended Kalman filtering are described. The report also covers investigations on upscaling and downscaling, segmentation for data processing, and applications to ground penetrating radar and geohydraulic tomography.

Energy Technology Data Exchange (ETDEWEB)

Proposed ductile fracture toughness parameters from tensile tests have been successfully used to determine the post-weld heat treatment temperature for an alloy 800/(9Cr-1Mo) steel dissimilar metal weld joint that is optimum with respect to accelerated aging, which simulates service conditions. This approach proved superior to using microstructural analysis, microhardness profiles, and conventional tensile properties. (author).

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionThis proposal seeks to extend what is currently the most comprehensive offshore environmental data collection programme at a platform on the UKGS involving continuous collection of wave height and direction, wind speed and direction, current and wave particle kinematics. Data has been collected with this system since 1994 and the proposal is to extend this until 1999 thus providing an extensive set of storm data collected at 5Hz which will allow examination of the joint behaviour of wave, wind [continued...

Energy Technology Data Exchange (ETDEWEB)

The magnetoresistance in an FeNi submicron-structure comprising two wires of 80 and 200 nm in width connected in series was measured at 77 K. When the external magnetic field was applied parallel to the wire axis, two switching fields corresponding to the distinct coercive force of the two wires were observed. When the external magnetic field was applied at an angle of {theta}>30 deg. to the wire axis one switching field was observed, indicating simultaneous magnetization reversal in both wires. This indicates that the domain-wall trapping around the joint can be controlled systematically in terms of the direction of the external magnetic field.

Energy Technology Data Exchange (ETDEWEB)

The integrity of a pipeline system is determined by its weakest links which may be the joints. Heat fusion is the most common method for joining gas distribution polyethylene (PE) piping. There are procedural, thermal, and mechanical aspects of making fusion joints. Acceptable procedural aspects, such as heater calibration and cleanliness, can be assured by rigorous training and certification of the operators. Thermal and mechanical aspects consist of specifying joining conditions such as the heater temperature, heating time, and joining pressure. In the absence of procedural errors, the strength of a fusion joint should depend on the pipe material, pipe dimensions, and the thermal and mechanical joining conditions. Socket heat fusion was studied both experimentally and analytically to determine how the strength of the joint varied with the conditions under which it was made. The standard tensile impact ...

Science.gov (United States)

PMID:17508608

Science.gov (United States)

Examines the effects of computer-based manufacturing technologies on employment opportunities and job skills. Describes the establishment of the Industrial Technology Institute in Michigan to develop and utilize advanced manufacturing technologies, and the institute's relationship to the state's community colleges. Reviews lessons learned from interinstitutional cooperation. Highlights future challenges. (DMM)

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... 2010-10-01 true Information Technology Virus Security. 2452...Clauses 2452.239-71 Information Technology Virus Security. As prescribed...the following clause: Information Technology Virus Security (FEB...

Science.gov (United States)

...2010-10-01 false Standards for health information technology to protect electronic health information...DEPARTMENT OF HEALTH AND HUMAN SERVICES HEALTH INFORMATION TECHNOLOGY HEALTH INFORMATION TECHNOLOGY STANDARDS, IMPLEMENTATION...

International Science & Technology Center (ISTC)

Development of SHS-technologies for SiC, Si3N4 and Ceramic Composites on Their Basis from Rocks

Science.gov (United States)

Information Technology Glossary of Terms. Applets: Programs that run inside net browsers, usually in Java and typically involving modestly interactive ...

Energy Technology Data Exchange (ETDEWEB)

This document requires a separate file for the figures. It is for DOE's Office of Vehicle Technologies Annual Report

Science.gov (United States)

adaptations of analog audio technology Recent developments in tape cassette technolocy have made Itpossible to provide up to ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of this R and D project are as follows : First, transferring developed technologies to outside companies and operating technology market to vitalize technology transactions, Second, developing commercial application projects to transfer technologies for commercial purposes and to solve interface problems in commercial applications, Third, enhancing commercial utilizations of developed accelerator and beam utilization technologies, Finally. preparing infra-structures for the development of over 30 venture- businesses based on achieved technologies through the Proton Engineering Frontier Project.

International Nuclear Information System (INIS)

A distinguishing design feature of CANDU nuclear reactors is the use of horizontal fuel channels housed in a horizontal vessel called a calandria, which is made of stainless steel 304L. Each channel consists of a Zr-2.5%Nb alloy pressure tube and an externally concentric Zr-2 calandria tube. The calandria tubes are joined to the end plates (tubesheets) of the calandria vessel by joints formed by roller expansion. The bores in the tubesheets are grooved. Roller expanded joints provide a cost effective means of joining dissimilar materials, require minimal space and no maintenance. The quality of these roller expanded joints is important from a sealing, strength and stress corrosion point of view. The roller expansion process consists of expanding the calandria tubes to deform them plastically against the bores and into the grooves of the tubesheets. Therefore, understanding the effect of the number, geometry and the pitch of ...

Energy Technology Data Exchange (ETDEWEB)

When completed, Lawrence Livermore National Laboratory's (LLNL) National Ignition Facility (NIF) will be the world's largest laser with experimental capabilities applicable to stockpile stewardship, energy research, science and astrophysics. As construction of the conventional facilities nears completion, operations supporting the installation of specialized laser equipment have come online. Playing a critical role in the precision cleaning of mechanical parts from the NIF beamline are three pieces of aqueous cleaning equipment. Housed in the Optics Assembly Building (OAB), adjacent to NIF's laser bay, are the large mechanical parts gross cleaner (LMPGC), the large mechanical parts precision cleaner (LMPPC), and the small mechanical parts gross and precision cleaner (SMPGPC). These aqueous units, designed and built by Sonic Systems, Inc., of Newtown, Pennsylvania, not only accommodate parts that vary greatly in size, weight, geometry, surface finish and ...

British Library Electronic Table of Contents (United Kingdom)

The effective integration of technology into the teaching and learning of mathematics remains one of the critical challenges facing contemporary tertiary mathematics. This article reports on some significant findings of a wider study investigating the use of technology in undergraduate mathematics. It first discusses a taxonomy developed to describe and compare technology use within individual courses and departments that identifies a complex range of factors, summarized under six defining characteristics of an integrated technology mathematics curriculum (ITMC). An instrument for a simple comparison of technology use employing the elements of this taxonomy is provided. It then presents evidence gathered from an observational study of technology implementation at The University of Auckland...

Energy Technology Data Exchange (ETDEWEB)

The effect of accelerated thermal cycling on a joint between modified 9Cr-1Mo steel (Grade 91) and Alloy 800 welded with Inconel 82 and 182 filler material is discussed. This is part of a trimetallic transition joint involving Grade 91-Alloy 800-316LN austenitic stainless steel for steam generator application. It has been shown that, during thermal cycling following the typical post-weld tempering treatment at 760 deg. C for 2 h, no carbon diffusion occurs from the ferritic steel towards the weld metal. There is, in fact, a hardness increase at the ferritic steel/weld metal interface which is probably a result of work hardening. Carbon migration sets in only after unusually long post-weld heat treatments for 20 and 50 h at 760 deg. C followed by thermal cycling. Significantly, even under the most severe thermal cycling test conditions imposed, no cracking or oxide notching could be detected, thus demonstrating the superior performance potential ...

CERN Document Server

We report on the spectral cross-calibration results of the Konus-Wind, the Suzaku/WAM, and the Swift/BAT instruments using simultaneously observed gamma-ray bursts (GRBs). This is the first attempt to use simultaneously observed GRBs as a spectral calibration source to understand systematic problems among the instruments. Based on these joint spectral fits, we find that 1) although a constant factor (a normalization factor) agrees within 20% among the instruments, the BAT constant factor shows a systematically smaller value by 10-20% compared to that of Konus-Wind, 2) there is a systematic trend that the low-energy photon index becomes steeper by 0.1-0.2 and Epeak becomes systematically higher by 10-20% when including the BAT data in the joint fits, and 3) the high-energy photon index agrees within 0.2 among the instruments. Our results show that cross-calibration based on joint spectral analysis is an important step to ...

CERN Document Server

The extraction of cosmological parameters from microwave background observations relies on specific assumptions about the statistical properties of the data, in particular that the p-point distributions of temperature fluctuations are jointly-normal. Using a battery of statistical tests, we assess the multivariate Gaussian nature of the Wilkinson Microwave Anisotropy Probe (WMAP) 1st year data. The statistics we use fall into three classes which test different aspects of joint-normality: the first set assess the normality of marginal (one-point) distributions using familiar univariate methods; the second involves statistics that directly assess joint-normality; and the third explores the evidence of non-linearity in the relationship between variates. We applied these tests to frequency maps, `foreground-cleaned' assembly maps and all-sky CMB-only maps. The assembly maps are of particular interest as when combined with the ...

Science.gov (United States)

Understanding the influence of interfacial structures on the nanoarchitecture mechanical properties is of particular importance for its mechanical applications. Due to a small size of constituting nanostructural units and a consequently high volume ratio of such interfacial regions, this question becomes crucial for the overall mechanical performance. Boron nitride bamboo-like nanotubes, called hereafter boron nitride nanobamboos (BNNBs), are composed of short BN nanotubular segments with specific interfaces at the bamboo-shaped joints. In this work, the mechanical properties of such structures are investigated by using direct in situ transmission electron microscopy tensile tests and molecular dynamics simulations. The mechanical properties and deformation behaviors are correlated with the interfacial structure under atomic resolution, and a geometry strengthening effect is clearly demonstrated. Due to the interlocked joint interfacial ...

Energy Technology Data Exchange (ETDEWEB)

Despite their high medical relevance, the principles of lubrication in natural joints are still unclear. It is generally accepted, that the presence of hyaluronic acid (HA), the main component of the synovial liquid, plays an important role for the low friction observed. Furthermore, it is assumed that surface active lipids participate in the lubrication. Using a model system of lipid bilayers deposited on a polyelectrolyte (PE) cushion and in contact with HA solution, we started to investigate the effects of pressure and shear forces, as experienced by natural joints, on the internal structure of the SiO{sub 2}/PE/lipid/HA interface and the bulk HA solution by neutron reflectometry (NR), complemented by in situ ellipsometry and quartz crystal microbalance (QCM-D) measurements. Only on positively charged polyelectrolyte surfaces, the successful build-up of the model system could be demonstrated. By NR, the existence of an irreversibly absorbed, ...

International Nuclear Information System (INIS)

In 576 patients quantitative scintigraphy of the sacroiliac joints and the spinal cord with "9"9"mTc-pyrophosphate was performed. 328 were patients with proven ankylosing spondylitis according to the New York criteria. 120 were patients with a clinically and roentgenologically suspected ankylosing spondylitis and 128 persons formed a healthy control group. The count rate in small regions of interest (ROI) in the sacroiliac joints, the spinal cord and the os sacrum were compared on the basis of indexes. The scintigraphic data of patients with ankylosing spondylitis were compared with the healthy control group and with the radiographic findings and radiologic staging of the disease. In a longitudinal follow-up study during 1 to 6 years these investigations were continued together with clinical and roentgenological checks. Quantitative bone scintigraphy provides characteristic indexes for ankylosing spondylitis, indicating the increased mineral ...

Energy Technology Data Exchange (ETDEWEB)

The clinical courses of heterotopic ossification (HO) as a consequence of trauma and central nervous system insults have many similarities as well as dissimilarities. Detection is commonly noted at two months. The incidence of clinically significant HO is 10%-20%. Approximately 10% of the HO is massive and causes severe restriction in joint motion or ankylosis. The most common sign and symptom are decreased range of motion and pain. The locations are the proximal limbs and joints. Sites of HO about a joint may vary according to the etiology of the HO. Roentgenographic evolution of HO occurs during a six-month period in the majority of patients. Treatment modalities include diphosphonates, indomethacin, radiation, range of motion exercises, and surgical excision. Surgical timing differs according to etiology: traumatic HO may be resected at six months; spinal cord injury HO is excised at one year; and traumatic brain injury ...

Science.gov (United States)

The objective of the program is to develop technology that results in economical, industry produced, and commercially marketable wind energy systems. The purpose of the VAWT Design Technology Seminar for Industry was to provide for the exchange of the current state of the art and predictions for future VAWT technology. Emphasis was placed on technology transfer on Sandia's technical developments and on defining the available analytic and design tools.

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) and the University of California, San Diego (UCSD) have taken the unprecedented step of creating a collaborative, multi-disciplinary graduate education program and associated research agenda called the Engineering Institute. The mission of the Engineering Institute is to develop a comprehensive approach for conducting LANL mission-driven, multidisciplinary engineering research and to improve recruiting, revitalization, and retention of the current and future staff necessary to support the LANL' s national security responsibilities. The components of the Engineering Institute are (1) a joint LANL/UCSD degree program, (2) joint LANL/UCSD research projects, (3) the Los Alamos Dynamic Summer School, (4) an annual workshop, and (5) industry short courses. This program is a possible model for future industry/government interactions with university partners.

International Nuclear Information System (INIS)

A novel adhesive for carbon materials composed of phenol-formaldehyde resin, boron carbide and fumed silica, was prepared. The adhesive property of graphite joints bonded by the above adhesive treated at high-temperatures was tested. Results showed that the adhesive was found to have outstanding high-temperature bonding properties for graphite. The adhesive structure was dense and uniform even after the graphite joints were heat-treated at 1500 deg. C. Bonding strength was 17.1 MPa. The evolution of adhesive structure was investigated. The results indicated that the addition of the secondary additive, fumed silica, improved the bonding performance greatly. Borosilicate phase with better stability was formed during the heat-treatment process, and the volume shrinkage was restrained effectively, which was responsible for the satisfactory high-temperature bonding performance of graphite.

British Library Electronic Table of Contents (United Kingdom)

The paper discusses the aspects of repair and retrofitting technique adopted for a damaged reinforced concrete beam-column joint specimen under cyclic loading. A specimen designed based on Indian Standard specifications with consideration of seismic load but without adopting ductile detailing (NonDuctile) was investigated under reverse cyclic loading. Then, the damaged nonductile specimen was repaired with epoxy mortar and grouted using low viscous polymer, and retrofitted using fiber reinforced plastic (FRP) wrapping in beam and column components and steel plate jacketing in joint region. The experimental results showed that the retrofitted specimen not only regained its original strength and stiffness but also has overcome the deficiencies of nonductile detailing. The present study shows...

International Nuclear Information System (INIS)

The EU-home team is in charge of the R and D related to the ITER baffle first wall. Five small-scale mock-ups, using Be, CFC and W tiles and different armour/heat-sink material joints under development, have been fabricated and thermomechanically tested in FE200 (Le Creusot) and JUDITH (Juelich) electron beam facilities. The small-scale mock-ups have been submitted to thermo-mechanical fatigue tests (up to failure using accelerating techniques). The objective was to determine the performances of the armour material joints under high heat flux cycles. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Competitive bidding for ancillary services (A/S), in addition to bidding for energy, is increasingly recognized as an important part of electricity markets. In this paper, an LP-based approach is presented for solving the multi-product (i.e. energy and A/S products), multi-zone/area physical market dispatch problem. The approach can explicitly represent various constraints, such as reserve requirement constraints, network security limits, and sharing of constrained resource capacity (e.g. maximum unit generation) between energy and reserve. The joint dispatch method, which dispatches energy and reserve market concurrently, is extended to allow inter-zonal reserve trading in multi-zone competitive pool. Numerical examples are included to demonstrate the salient characteristics of the joint dispatch solution.

British Library Electronic Table of Contents (United Kingdom)

Summary The steadily growing epidemic of diabetes mellitus poses a threat for global tuberculosis (TB) control. Previous studies have identified an important association between diabetes mellitus and TB. However, these studies have limitations: very few were carried out in low-income countries, with none in Africa, raising uncertainty about the strength of the diabetes mellitus-TB association in these settings, and many critical questions remain unanswered. An expert meeting was held in November 2009 to discuss where there was sufficient evidence to make firm recommendations about joint management of both diseases, to address research gaps and to develop a research agenda. Ten key research questions were identified, of which 4 were selected as high priority: (i) whether, when and how to sc...

Science.gov (United States)

This document contains 142 papers on PT3 (Preparing Tomorrow's Teachers to use Technology) from the SITE (Society for Information Technology & Teacher Education) 2002 conference. Topics covered include: a technology in urban education summit; student professional development; meeting NCATE (National Council of Teachers of English) standards; faculty use of WebCT; preparing teachers for the digital age; technology in K-8 multicultural classrooms; using immersive 360 degree images; consortium building; student evaluation; technology fellows; incentives that facilitate institutional change; impact of a temporary grant; a consortium for outstanding achievement in teaching with technology; changes implemented after technology professional development sessions; Web-based modules for teaching mathematics to minority students; student teaching ...

UK PubMed Central (United Kingdom)

Although the demand for use of information technology within the healthcare industry is intensifying, relatively little has been written about guidelines to optimize IT investments. A technology architecture...Full Text Available

Science.gov (United States)

As requested by the Under Secretary of Defense (Acquisition, Technology, and Logistics) and the Director DARPA, the Defense Science Board task force performed a one-time independent evaluation of the technology investment for the Defense Advanced Research...

Science.gov (United States)

... and technology-. The United States National Technology Roadmap for Semiconductors [ 11 still ... Moreover, higher volumes of production, better manufacturing capabilities and ... energy-efficient, reliable, high-performance, embedded (real-time), highly miniaturized, .... Optical Computing, Storage, and Communications. ...

Energy Technology Data Exchange (ETDEWEB)

What technical, economic and institutional factors make radioactive and/or hazardous waste management technologies publicly acceptable? The goal of this paper is to initiate an identification of factors likely to render radioactive and hazardous waste management technologies publicly acceptable and to provide guidance on how technological R&D might be revised to enhance the acceptability of alternative waste management technologies. Technology development must attend to the full range of technology characteristics (technical, engineering, physical, economic, health, environmental, and socio-institutional) relevant to diverse stakeholders. ORNL`s efforts in recent years illustrate some attempts to accomplish these objectives or, at least, to build bridges toward the integrated design of waste management technologies.

Energy Technology Data Exchange (ETDEWEB)

This paper first discusses the challenge offered by natural and anthropogenic systems in all of their complexity and then indicates some areas of research in which specific scientific and technological needs are identifiable.

Energy Technology Data Exchange (ETDEWEB)

A critical and difficult step in the development and implementation of new technologies for environmental monitoring and characterization is successfully transferring these technologies to industry and government users for routine assessment and compliance activities. The Environmental Sciences Section of the DOE Savannah River Technology Center provides a forum for developers, potential users, and regulatory organizations to evaluate new technologies in comparison with baseline technologies in a well characterized field test bed. The principal objective of this project is to conduct comprehensive, objective field tests of monitoring and characterization technologies that are not currently used in EPA standard methods and evaluate their performance during actual operating conditions against baseline methods. This paper provides an overview of the field test site ...

Science.gov (United States)

We report a unique type of ULF waves observed by low-altitude Space Technology 5 (ST-5)

Science.gov (United States)

Apr 9, 2003 ... Adam Kissiah Jr., a retired KSC engineer, will be honored for his development of the digital hearing aid technology that led to the cochlear ...

Science.gov (United States)

Jun 21, 2006 ... The competition is organized by the Marine Advanced Technology Education Center (MATE) and Marine Technology Society's (MTS) ROV Committee. ...

Science.gov (United States)

... Materials Development Program TECHNOLOGY EDUCATION INSTRUCTIONAL MATERIALS Elementary - High School ... of technology education materials through its Instructional Materials Development (IMD) program. The ...

Science.gov (United States)

Efficiency and Renewable Energy EERE Home | Programs & Offices | Consumer Information Chemicals Search Search Help Chemicals EERE » Industrial Technologies Program » Chemicals...

UK PubMed Central (United Kingdom)

PurposeHealth information technology (HIT) and physician career satisfaction are associated with higher-quality medical care. However, the link between HIT and physician...Full Text Available