International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The magnetoresistance in an FeNi submicron-structure comprising two wires of 80 and 200 nm in width connected in series was measured at 77 K. When the external magnetic field was applied parallel to the wire axis, two switching fields corresponding to the distinct coercive force of the two wires were observed. When the external magnetic field was applied at an angle of {theta}>30 deg. to the wire axis one switching field was observed, indicating simultaneous magnetization reversal in both wires. This indicates that the domain-wall trapping around the joint can be controlled systematically in terms of the direction of the external magnetic field.

International Nuclear Information System (INIS)

The integrity of helium circulation loop flanged joints has been attracting recent attention as a design problem, in the development of high-temperature facilities incorporating helium loops (e.g., the VRG-50 pilot nuclear facility). Elevated temperatures and pressures, and the radiation environment, impose additional requirements on sealant materials. This applies first and foremost to rubber seals, which have found widespread favor on account of its excellent elasticity, its ability to spontaneously conform to possible changes in the clearance in the seal assembly, and the low compressive stresses developed in the flange joint assembly.

Energy Technology Data Exchange (ETDEWEB)

Considering beryllium as plasma facing armour this paper presents recent results obtained in Russia. A special process of joining beryllium to a Cu-alloy material structure is described and recent results of thermal cycling tests of such joints are presented. Summarizing the results, the authors show that a Cu-alloy heat sink structure armoured with beryllium can survive high heat fluxes ({>=}10 MW/m{sup 2}) during 1000 heating/cooling cycles without serious damage to the armour material and its joint. The principal feasibility of thermal cycling of beryllium grades and their joints directly in the core of a nuclear reactor is demonstrated and the main results of this test are presented. The paper also describes the thermal cycling of different beryllium grades having cracks initiated by previously applied high heat loads simulating plasma disruptions. (orig.)

Science.gov (United States)

... 3 Joint Committee on Atomic Energy as a Model . . . . . ... Joint Committee on Atomic Energy as a Model Page 8. CRS-4 ...

British Library Electronic Table of Contents (United Kingdom)

Cache locking technique is often utilized to guarantee a tighter prediction of Worst-Case Execution Time (WCET) which is one of the most important performance metrics for embedded systems. However, in Multi-Processor Systems-on-Chip (MPSoC) systems with multi-tasks, Level 2 (L2) cache is often shared among different tasks and cores, which leads to extended unpredictability of cache. Task assignment has inherent relevancy for cache behavior, while cache behavior also affects the efficiency of task assignment. Task assignment and cache behavior have dramatic influences on the overall WCET of MPSoC. This paper proposes joint task assignment and cache partitioning techniques to minimize the overall WCET for MPSoC systems. Cache locking is applied to each task to guarantee a precise WCET. We pr...

CERN Document Server

The extraction of cosmological parameters from microwave background observations relies on specific assumptions about the statistical properties of the data, in particular that the p-point distributions of temperature fluctuations are jointly-normal. Using a battery of statistical tests, we assess the multivariate Gaussian nature of the Wilkinson Microwave Anisotropy Probe (WMAP) 1st year data. The statistics we use fall into three classes which test different aspects of joint-normality: the first set assess the normality of marginal (one-point) distributions using familiar univariate methods; the second involves statistics that directly assess joint-normality; and the third explores the evidence of non-linearity in the relationship between variates. We applied these tests to frequency maps, `foreground-cleaned' assembly maps and all-sky CMB-only maps. The assembly maps are of particular interest as ...

Science.gov (United States)

Not Available

Environmental Research Database

No further description is available

Science.gov (United States)

Not Available

Science.gov (United States)

... directed the transformation of designated Service operational headquarters into effective and scalable Joint Task Force headquarters capable of ...

Energy Technology Data Exchange (ETDEWEB)

The behavior of MEMS devices is limited by the strength of critical features such as thin ligaments, oxide cuts joining layers, pin joints and hinges. Devices fabricated at Sandia's Microelectronic Development Laboratory have been successfully tested to investigate these features. A series of measurements were performed on samples with gage lengths of 15 to 1000 microns, using conventional and tungsten coated samples as well as samples that include the critical features of standard components in the test section. Specimens have a freely moving pin joint on one end that anchors the sample to the silicon die to allow rotation to reduce effects of bending. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. Load is calculated by resolving the measured lateral and normal forces into the applied tensile force and frictional losses. The specimen ...

International Nuclear Information System (INIS)

This is the second revision of the ETDE/INIS Joint Thesaurus, including all updates up to September 2006. It contains 21 147 valid descriptors and 9 114 forbidden terms. The Joint Thesaurus contains the controlled terminology for indexing all information within the subject scopes of the International Nuclear Information System (INIS) and the Energy Technology Data Exchange (ETDE). The terminology is intended for use in subject descriptions for input or retrieval of information in these systems. The thesaurus is a terminological control device used in translating from the natural language of documents, indexers or users into a more constrained system language It is also a controlled and dynamic vocabulary of semantically and generically related terms which covers a specific domain of knowledge. The basic terminology in this thesaurus goes back to the 1969 edition of the EURATOM Thesaurus. The structure subsequently given to that terminology was ...

International Nuclear Information System (INIS)

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

Energy Technology Data Exchange (ETDEWEB)

A new method for analysis and design of smoothing reactances utilising two-dimensional planar models is presented in this paper. Inductance and magnetic flux density are calculated, and their results compared with those measured experimentally. The results obtained are good if compared with those measured once the machine have been built. Moreover, the method herein developed is applied to the calculation of air gap lengths in terms of the desired current and inductance. The kind of reactances studied presents windings in both limbs and air gaps in the four corners (joint of limbs and yokes). The main contribution of this paper is the presentation of a method of industrial application, to be easily developed, with a very important reduction in the time of machine calculation (due to the decrease in the number of nodes and elements compared with the three-dimensional model) for the determination of the air gap length in smoothing reactances. ...

Energy Technology Data Exchange (ETDEWEB)

Ceramic ball bearings of silicon nitride are used for hard disk drive (HDD) spindle motors, to increase seed, reliability and memory capacity of the HDDs. Silicon nitride ceramics have advantages of lightweight, high strength and hardness over the conventional steel for bearings, but is expensive. A new process of high cost performance has been developed for mass production of the small-size ceramic balls. The company plans to apply these bearings to higher devices, e.g., servers, for the time being, and to expand the applicable areas, e.g., common devices and other small-size motors. The ceramic bearings have been developed jointly with Koyo Seiko Co. Ltd. (translated by NEDO)

British Library Electronic Table of Contents (United Kingdom)

An assessment of the joint shear strength of exterior concrete beam-column joints reinforced internally with Glass Fibre Reinforced Polymer (GFRP) reinforcements under monotonically increasing load on beams keeping constant load on columns is carried out in this study. Totally eighteen numbers of specimens are cast and tested for different parametric conditions like beam longitudinal reinforcement ratio, concrete strength, column reinforcement ratio, joint aspect ratio and influence of the joint stirrups at the joint. Also finite element analysis is performed to simulate the behaviour of the beam-column joints under various parametric conditions. Based on this study, a modified design equation is proposed for assessing the joint shear strength of the GFRP reinforced beam-column specimens b...

UK PubMed Central (United Kingdom)

Hyaluronan (HA) is important for joint cavitation, lubrication, volume regulation and synovial fluid drainage but little is known about the regulation of joint HA synthesis/secretion in vivo....Full Text Available

Science.gov (United States)

Special Operations Forces (SOF) within a Joint Task Force are controlled by a Joint Special Operations Task Force (JSOTF). Presently, JSOTF headquarters are formed around the core of the Theater Special Operations Command (TSOC), a service SOF headquarter...

Science.gov (United States)

Information superiority provides the Joint force a competitive ... Information Grid (GIG) as it matures and fills the needs of the Joint Task Force ... representatives from The Army Secretariat, Headquarters Department of Army ...

British Library Electronic Table of Contents (United Kingdom)

The addition of ?-Sialon nanoparticles to lubricants in heavy-duty frictional joints is shown to be effective.

Science.gov (United States)

... Chiefs of Staff, Joint Operation Planning and Execution System (JOPES) Volume I, Planning and Procedures, CJCSM 3122.01A (Washington, DC ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: The aim of this study was to evaluate the accuracy of MRI in the measurement of cartilage thickness of the ankle joint in comparison to pathologic and histologic specimens. Patients and methods: The ankle joints of four fresh cadaver feet were imaged on a 1.5 T MR-unit in the coronal plane. Standard T{sub 1}-weighted spin echo (SE) and a T{sub 1}-weighted 3D-GE (FLASH-3D) sequence with fat saturation were applied. Following MR imaging, the talus was explanted and cut parallel to the MR images for macroscopic evaluation and histologic specimens were prepared. MRI measurements of the cartilage thickness of the talus were carried out in two ways: Without and with consideration of a transition zone of intermediate signal intensity between hyperintense cartilage and hypointense cortical bone. The data were compared with the anatomic specimens as the gold standard expressing the difference as a percentage value. On ...

International Nuclear Information System (INIS)

Published in summary form only.

Medline Plus

... many bones. The bones are separated by special hinges called joints. Muscles make the bones move on ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The Joint Convention on the Safety of Spent Fuel management and on the Safety of Radioactive Waste Management is the first legal instrument to directly address the safety of spent fuel and radioactive waste management on a global scale. The Joint Convention entered into force in 2001. This paper describes its process and its main achievements to date. The perspectives to establish of a Global Waste Safety Regime based on the Joint Convention are also discussed. (authors)

Science.gov (United States)

Joint Diseases

Energy Technology Data Exchange (ETDEWEB)

The effect of aging on the microstructure and tensile properties of a type 316LN stainless steel/Alloy 800 joint, welded with 16-8-2 stainless steel consumable, has been studied to characterize and evaluate the joint for long-term elevated temperature service. The joint was subjected to accelerated againg heat treatments at 873 K up to 5000 h to simulate long-term service exposures. Analysis of the results from this investigation shows that this joint has adequate stability of microstructure and tensile properties even after prolonged exposure at elevated temperatures. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This report to the Nuclear Regulatory Commission (NRC) describes the development and application of a methodology to systematically and quantitatively assess predictive uncertainty in groundwater flow and transport modeling that considers the combined impact of hydrogeologic uncertainties associated with the conceptual-mathematical basis of a model, model parameters, and the scenario to which the model is applied. The methodology is based on a n extension of a Maximum Likelihood implementation of Bayesian Model Averaging. Model uncertainty is represented by postulating a discrete set of alternative conceptual models for a site with associated prior model probabilities that reflect a belief about the relative plausibility of each model based on its apparent consistency with available knowledge and data. Posterior model probabilities are computed and parameter uncertainty is estimated by calibrating each model to observed system behavior; prior parameter estimates ...

CERN Document Server

This paper is focused on solving the narrowband direction of arrival estimation problem from a sparse signal reconstruction perspective. Existing sparsity-based methods have shown advantages over conventional ones but exhibit limitations in practical situations where the true directions are not in the sampling grid. A so-called off-grid model is broached to reduce the modeling error caused by the off-grid directions. An iterative algorithm is proposed in this paper to solve the resulting problem from a Bayesian perspective while joint sparsity among different snapshots is exploited by assuming the same Laplace prior. Like existing sparsity-based methods, the new approach applies to arbitrary sensor array and exhibits increased resolution and improved robustness to noise and source correlation. Moreover, our approach results in more accurate direction of arrival estimation, e.g., smaller bias and lower mean squared error. High precision can be ...

International Nuclear Information System (INIS)

The Compton backscatter technique has been applied to lap-joint in aircraft structure in order to determine mass loss due to exfoliative corrosion of the aluminum alloy sheet skin. The mass loss of each layer has been estimated from Compton backscatter A-scan including the aluminum sheet, the corrosion layer, and the sealant. A Compton backscattering imaging system has been also developed to obtain a cross-sectional profile of corroded lap-splices of aging aircraft using a specially designed slit-type camera. The camera is to focus on a small scattering volume inside the material from which the backscattered photons are collected by a collimated scintillator detector for interpretation of material characteristics. The cross section of the layered structure is scanned by moving the scattering volume through the thickness direction of the specimen. The theoretical model of the Compton scattering based on Boltzmann transport theory is presented ...

CERN Document Server

The field of digital libraries (DLs) coalesced in 1994: the first digital library conferences were held that year, awareness of the World Wide Web was accelerating, and the National Science Foundation awarded $24 Million (U.S.) for the Digital Library Initiative (DLI). In this paper we examine the state of the DL domain after a decade of activity by applying social network analysis to the co-authorship network of the past ACM, IEEE, and joint ACM/IEEE digital library conferences. We base our analysis on a common binary undirectional network model to represent the co-authorship network, and from it we extract several established network measures. We also introduce a weighted directional network model to represent the co-authorship network, for which we define $AuthorRank$ as an indicator of the impact of an individual author in the network. The results are validated against conference program committee members in the same period. The results ...

CERN Document Server

Applied survey methods

Science.gov (United States)

Not Available

British Library Electronic Table of Contents (United Kingdom)

An effective rehabilitation strategy is proposed to enhance the strength and stiffness of the beam-column joint in this study. An analytical model is proposed to predict the column shear of the joints strengthened with carbon fiber reinforced polymer (CFRP). Three full scale interior beam-column joints, including two specimens strengthened with CFRP and one prototype specimen, are tested in this study. The specimens are designed to represent the pre-seismic code design construction in which there is no transverse reinforcement. A new optical non-contact technique, digital image correlation (DIC), which can measure the full strain field of specimen, is used to measure and observe the full strain field of the joint. The experimental results show that the beam-column joints strengthened with ...

UK PubMed Central (United Kingdom)

AIM: To evaluate the effects of percutaneous ozone injection via the posterior-lateral route and inner margin of the facet joint in the treatment of large lumbar disc herniation.METHODS:...Full Text Available

International Nuclear Information System (INIS)

Exact anatomic knowledge about the location of the gonads and the application of corresponding measures of radiation protection are the preconditions for an efficient reduction of the danger of a possible genetic damage as a result of radiation exposition during X-ray examination of the hip joint of newborns. (VJ).

UK PubMed Central (United Kingdom)

We studied multi-joint coordination during tasks of transporting real and imaginary objects with two arms. One of the arms was unexpectedly arrested in one third of trials performed. In the...Full Text Available

Science.gov (United States)

... II Item Identification 1,2,3,4,5,,3JAN Joint Army-Navy 2 5,6,13 IIM Item Intelligence 2 JANAP Joint Army-Navy-Air 2,7 Maintenance Force Publication ...

UK PubMed Central (United Kingdom)

Examination of a painful hip is fairly concise and reliable at detecting the presence of a hip joint problem. Hip joint disorders often go undetected, leading to the development of secondary disorders....Full Text Available

International Nuclear Information System (INIS)

The structure of a demountable vacuum joint designed for operation from -120 to +120 deg C is developed and tested. Requirements of especially low gas release from the materials used have been fulfilled; the same concerns low sealing efforts, repeated action and keeping tightness under loads, indium being used as a sealant. Experimental studies of demountable vacuum joints, dia 100,125,140,160,180 and 200 mm, with an indium sealant permit to make the following conclusions: 1. The joints are sealed at sealing specific efforts of 0.4 kg/mm (without considering atmospheric pressure). 2. The joints retain tightness at opening and closing a cover five times and under +-120 deg C. 3. To ensure repeated operation of the joint with continued stable sealing effort, one should make sure the sealed surfaces coincide at repeated sealing. 4. When operating demountable vaccum ...

Energy Technology Data Exchange (ETDEWEB)

Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting the joint project integrating both the Neutron Science Project (NSP) of JAERI and the Japan Hadron Facility Project (JHF) of KEK for comprehensive studies on basic science and technology using high-intensity proton accelerator. This document describes the joint project prepared by the Joint Project Team of JAERI and KEK to construct accelerators and research facilities necessary both for the NSP and the JHF at the site of JAERI Tokai Establishment. It was originally written in English and translated into Japanese with some corrections. (author)

Science.gov (United States)

... The second section describes the role and functions of a corps as a joint task force headquarters and uses Operation Uphold Democracy ...

Science.gov (United States)

(January 1999) - PDF File (36K)

Science.gov (United States)

runs are necessary, provision shall be made for expansion joints, motion of the units, or similar compensation to ensure that no excessive strains are ...

Science.gov (United States)

... Training System (JMATS) for joint C-130J training. However, the ... the C-130J's being procured by the Air Force. A logical ...

Energy Technology Data Exchange (ETDEWEB)

Published in summary form only.

Science.gov (United States)

... to integrate and synchronize SC efforts and capabilities, as noted in the SC Roadmap, the joint community needs to publish SC policy and expand ...

Energy Technology Data Exchange (ETDEWEB)

In January 2001, Husky Oil Operations Limited (Husky), in joint-venture with Petro-Canada, submitted a Benefits Plan for the White Rose Development to the Canada-Newfoundland and Labrador Offshore Petroleum Board (C-NLOPB). It was prepared following the Canada-Newfoundland and Labrador Atlantic Accord Implementation Act and the Canada-Newfoundland and Labrador Atlantic Accord Implementation (Newfoundland) Act. In December 2001, the C-NLOPB approved the White Rose Benefits Plan. This document described the work that Husky proposes to undertake within its significant discovery license areas 1043 and 1044 for the development of the South White Rose Extension (SWRX) Tie-back to the White Rose Floating Production, Storage and Offloading (FPSO) vessel as it will require an amendment to the original White Rose Development Plan and is subject to the review and approval of the C-NLOPB. The statutory requirements as well as the actual policies and procedures were identified ...

International Nuclear Information System (INIS)

Authors obtained T1-weighted MRI images of the femoral head after fracture of the femoral neck and classified the signals into four patterns to investigate the sequential changes of the femoral head. The T1-weighted MRI images obtained initially after femoral neck fracture showed a normal pattern in 10 of the 15 hip joints studied. MRI images obtained subsequently still showed the normal signal pattern in eight of the 10 hip joints which had shown the normal pattern in the first MRI, while two of the 10 joints subsequently showed a band pattern. The joint with the homogeneous pattern in the first MRI subsequently showed a band pattern. Of the three joints with an inhomogeneous pattern in the first MRI, two joints showed a subsequent band pattern, and the other a normal pattern. The joints which showed a band pattern continued to show a ...

International Nuclear Information System (INIS)

As an engineered barrier system in the geological disposal of high-level waste, multibarrier system is considered. Multibarrier system consists of the vitrified waste, the overpack and the buffer. Bentonite is one of the potential material as the buffer because of its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. As the construction technology of the buffer, the block installation method and in-situ compaction method, etc, are being investigated. The block installation method is to emplace the buffer blocks manufactured in advance at the ground facility, and construction processes of the block installation method at the underground will be simplified compared with the in-situ compaction method. However, the block joints of buffer might be a mechanical weak portion or might be a preferential ...

Energy Technology Data Exchange (ETDEWEB)

Measurements of human joint motion frequently involve the use of opto-electronic and other motion analysis systems where some type of makers are used to establish joint motion within a global reference coordinate frame. Typically, this global reference coordinate frame is chosen to be most convenient for the person carrying out the experiment in which the joint motion is measured, and Euler angles are chosen as the measure of joint motion. Results, however, may be quite arbitrary and therefore rendered meaningless if the reference frame is not properly chosen with respect to the physical joint axis. In order to make a proper choice of coordinate axes in the reference frame, one must take into consideration both the location and the orientation of die physical joint axis relative to the reference frame`s axes. In nature, joint axes can exist ...

Energy Technology Data Exchange (ETDEWEB)

There are currently no accepted industry standards for the tensile strain limits of girth welds. This paper investigated the behavior of girth welds with buried defects subjected to high longitudinal strains caused by soil movement. A strain design methodology based on a crack driving method was used to examine the factors influencing stain limits along with a constraint-sensitive fracture mechanics approach. No strength undermatching was used in the welds, and the defect location had no influence on crack driving force. The weld joint was assumed to have uniform tensile properties. A 3D finite element (FE) model was used to simulate pipe behavior. Symmetric boundary conditions were imposed on the symmetry planes, and uniform remote axial displacement was applied as the primary loading. Automated data processing routines were developed to extract and analyze the data. The crack driving force was computed directly from a crack tip deformation ...

International Nuclear Information System (INIS)

This paper describes the unique challenges involved in achieving compliance with the Resource Conservation and Recovery Act (Public Law 94-580) Land Disposal Restrictions (LDR) treatment standards for four types of mixed wastes generated throughout the U.S. Department of Energy (DOE) complex: (1) radioactively contaminated lead acid batteries; (2) radioactively contaminated cadmium-, mercury-, and silver-containing batteries; (3) mercury-bearing mixed wastes; and (4) radioactive lead solids. For each of these mixed waste types, the paper identifies the strategy pursued by DOE's Office of Pollution Prevention and Resource Conservation Policy and Guidance (EH-43) in coordination with other DOE elements and the U.S. Environmental Protection Agency (EPA) to meet the compliance challenge. Specifically, a regulatory interpretation was obtained from EPA agreeing that the LDR treatment standard for wastes in the D008 'Radioactive Lead Solids' sub-category applies to ...

Energy Technology Data Exchange (ETDEWEB)

We compiled the results of the source analysis obtained under the collaboration research. Recent construction scheme for source modeling adopted in Japan is described, and strong-motion prediction is performed assuming the scenario earthquakes occurring in the Ulsan fault system, Korea. Finally Qs values beneath the Korean inland crust are estimated using strong-motion records in Korea from the 2005 Off West Fukuoka earthquake (M7.0). Probabilistic seismic hazard for four NPP sites in Korea are evaluated, in which the site specific attenuation equations with Index SA developed for NPP sites are adopted. Furthermore, the uniform hazard spectra for the four NPP sites in Korea are obtained by conducting the PSHA by using the attenuation equations with the index of response spectra and seismic source model cases with maximum weights. The supporting tools for seismic response analysis, the evaluation tool for evaluating annual probability of failure, and system analysis program were ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility study is conducted for introduction of a top pressure recovery turbine (TRT) in China's Panzhihua Iron and Steel (Group) Company, Sichuan Province, for the potential project to simultaneously contribute to abatement of the greenhouse effect gases and to sustainable economic development of the counterpart country. This project considers to adopt the TRTs in 3 blast furnaces (No.1 to 3) of the 4 furnaces in service at the works, producing 2,500,000 t/y of crude steel, where the No.4 furnace is already provided with the model system and not considered in this project. According to the feasibility study results, the total fund required is 5.46 billion yen (Japan-made facilities: 4.172 billion yen, and China-made facilities: 1.288 billion yen), energy-saving effect is 36,467 t/y as crude, greenhouse effect gas emission abatement effect: 112,830 t/y as CO2, and pay-off period is 8.3 years. This plan considers to adopt almost the same facilities as those for the model ...

Energy Technology Data Exchange (ETDEWEB)

The kraft recovery boiler is of critical importance for the paper and pulp industry. From only energy point of view, kraft recovery boilers supply more than 50% of total thermal energy consumed in the paper and pulp industry. A kraft recovery boiler has two main functions: firstly to recover the inorganic cooking chemicals in the black liquor for reuse in the pulping process, and secondly to make use of the chemical energy in the organic portion of the black liquor to generate super-heated steam for the plant. The twin objectives of recovering chemicals and energy makes the recovery boiler design and operation more complex than virtually any other boiler application. Thus there is a demand for development of an analytical tool that can be used to predict the performance of a kraft recovery boiler. This paper presents the results achieved from a project jointly financed by Swedish National Energy Administration and the industry (Iggesund Paperboard). In this ...

Energy Technology Data Exchange (ETDEWEB)

Twenty-seven patients with symptoms or clinical findings suggesting joint or bone disorders of the anterior chest wall (ACW) were evaluated by spiral CT with 3-dimensional (3-D) and multiplanar reconstructions. Preceding conventional ACW tomography was performed in 10 patients. ACW joint and bone changes were visualized more adequately by coronal 2-D reconstructions based on spiral CT than by conventional tomography. In addition, nonossified costal cartilages and soft tissue lesions were demonstrated. 3-D reconstructions sometimes added information, especially in patients with fracture and dislocation. (orig.).

British Library Electronic Table of Contents (United Kingdom)

Magnetic resonance (MR) imaging and histopathology were used to diagnose an articular process synovial myxoma in a dog. On MR images, the tumor was characterized by distortion of the left L1-L2 articular process, widening of the articular process joint, and the presence of a mass contiguous with the synovium of the articular process that displaced the spinal cord. The tumor was T2-hyperintense, T1-hypointense, relative to muscle, and had mild contrast enhancement. The MR features of articular process synovial myxoma may be distinct from other diseases of the articular process joint.

Science.gov (United States)

Microscopy and chemotaxonomy from HPLC analysis of phytoplankton pigments initiated in 2003 suggest that Noctiluca miliaris blooms are becoming more intense ...

Science.gov (United States)

Sep 8, 2005 ... one of the headquarters buildings here at Stennis, took off .... Also, they have a joint task force, that the ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Page 23. Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... United States Forces Command, Detachment 13 ... EUCOM Headquarters Support Detachment 1 ... 7th Joint Task Force Augmentation Team ...

Science.gov (United States)

... Concerning Persons and Organizations not Affiliated with the Department of Defense," January 7, 1980 (f) DoD 5240.1-R, "Procedures Governing ...

Science.gov (United States)

... Prior to 1977, one group, the Joint Committee on Atomic Energy, had oversight. Since 1977, this responsibility has been ...

Science.gov (United States)

... Joint Publication (JP) 5-0 (Washington DC: CJCS, 29 September ... and Execution System (JOPES) Volume 1. CJCSM 3122.01A (Washington, DC: 6 ...

Science.gov (United States)

... Joint Publication (JP) 5 (Washington, DC: CJCS, 26 December 2006 ... Policies and Procedures, (Washington, DC: CJCSM, 3122.01A 29 September ...

Science.gov (United States)

This paper summarizes the main features of four current REDD proposals: Compensated Reduction, Papua New Guinea et al; Joint Research Center; and Brazil. ... ...

Science.gov (United States)

... Joint Staff and other US Military (ie, Army, Navy, Air ... HEART RATE, AND BODY TEMPERATURE DURING WORK IN MAN, DOG, AND SWINE. ...

Science.gov (United States)

... WHS- Washington Headquarters Service ... but also with respect to other Joint, National and ... unit of action (UA) combat team or task force is organized ...

Science.gov (United States)

... established in allied communications publications (ACP); DISA circulars (DISAC), Joint Army-Navy-Air Force publications (JANAP), and MAJ- COM ...

Science.gov (United States)

... In this manner, a JBI-enabled COI would have the full suite of JBI information management capabilities, but would still be based on and have full ...

Science.gov (United States)

... Joint Staff and other US Military (ie, Army, Navy, Air ... The major products of this work are significant advances in ... Keywords: Dogs; Laboratory animals ...

DEFF Research Database (Denmark)

OBJECTIVE: To evaluate the interobserver agreement of ultrasonographic assessment of finger and toe joints in patients with rheumatoid arthritis (RA) by 2 investigators with different medical backgrounds. METHODS: Ultrasonography and clinical examination were performed on 150 small joints of 30 patients with active RA. A General Electric LOGIQ 500 ultrasound unit with a 7-13-MHz linear array transducer was used. In each patient, 5 preselected small joints (second and third metacarpophalangeal, second proximal interphalangeal, first and second metatarsophalangeal) were examined independently on the same day by 2 ultrasound investigators (an experienced musculoskeletal radiologist and a rheumatologist with limited ultrasound training). Joint effusion, synovial thickening, bone erosions, and power Doppler signal were evaluated in accordance with an introduced 4-grade semiquantitative scoring system, on ...

Science.gov (United States)

... Experts ( Appendix 5 ), and the NMFS-Sea Grant Joint Graduate Fellowship Program ( Appendix 6) . The Task Force consisted of one representative from NMFS Headquarters and 1-2 rep...

Science.gov (United States)

9-foot 9-inch blocks of concrete with asphaltic-filled expansion joints. The concrete was placed on 4 to 6 inches of gravel or #4 stone. ...

Science.gov (United States)

... WHS- Washington Headquarters Service. ... The standing Joint Task Force concept should be used more to provide warfighter forces and ...

Science.gov (United States)

... the USCINCPAC staff and the staff of the commander, US Seventh Fleet, as a designated Pacific Command Joint Task Force Headquarters, in crisis ...

Science.gov (United States)

... Page 25. US Department of Defense, Joint Operation Planning and Execution System, Vol 1, Planning Policies and Procedures (CJCSM 3122.01A). ...

Science.gov (United States)

Feb 6, 2003 ... Director, Plans and Programs, Headquarters Air Force Materiel Command, .... Commander of the Joint Task Force Southwest Asia at Prince ...

Science.gov (United States)

... (l0)6o). 316. Statf,'ent. In Hearings before the Subcommittee on Research, Do'v,-Iopment, and Radiation of the Joint Committee on Atomic Energy. ...

Science.gov (United States)

joint task force (JTF), division (OIV) and regimental combat team (RCT) with ..... Headquarters, Department of the Army. (HQOA), (2010). Field Manual 2-0 ...

British Library Electronic Table of Contents (United Kingdom)

A joint experimental and theoretical analyses based on the grounds of DFT anharmonic potential and the use of a variational method allow us to revisit and assign the gas phase spectra of vinylarsine in the mid-IR area until 6300cm-1. Several weak and very weak bands corresponding to overtones and combinations are newly observed and assigned in complement to the fundamental bands.

Energy Technology Data Exchange (ETDEWEB)

Through a comprehensive and aggressive research program Consolidated Edison Company of New York, Inc. (Con Edison) has designed, developed, and installed several new products to address the environmental impact of dielectric fluid from pipe-type cable systems. These include: On Line Leak Detection, Leak Location, Retractable Flow Direction Indicator, Full Stop Joints, and Transition Joints. This paper describes the application of the aforementioned products on the Con Edison underground transmission system.

Energy Technology Data Exchange (ETDEWEB)

According to the present invention, a joined product is at least two ceramic parts, specifically bi-element carbide parts with a bond joint therebetween, wherein the bond joint has a metal silicon phase. The bi-element carbide refers to compounds of MC, M.sub.2 C, M.sub.4 C and combinations thereof, where M is a first element and C is carbon. The metal silicon phase may be a metal silicon carbide ternary phase, or a metal silicide.

Science.gov (United States)

A report is presented of a hearing conducted before the Joint Committee on Atomic Energy on August 27, 1976, to discuss the legal implications for reactor licensing resulting from court challenges to procedures for assessing the environmental impact of radioactive waste disposal. (DG)

Energy Technology Data Exchange (ETDEWEB)

Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation of mechanical ...

Science.gov (United States)

Applying for AAO scheduled time Applying for AAT service time Applying for Gemini Time Travel and Accommodation AAT Schedule UKST Schedule Instrument capabilities and...

Science.gov (United States)

In the past few decades the need for improved nuclear reactor safety analyses has led to a rapid development of advanced methods for multidimensional thermal-hydraulic analyses. These methods have become progressively more complex in order to account for the many physical phenomena anticipated during steady state and transient Light Water Reactor (LWR) conditions. The advanced thermal-hydraulic subchannel code COBRA-TF (Thurgood, M. J. et al., 1983) is used worldwide for best-estimate evaluations of the nuclear reactor safety margins. In the framework of a joint research project between the Pennsylvania State University (PSU) and AREVA NP GmbH, the theoretical models and numerics of COBRA-TF have been improved. Under the name F-COBRA-TF, the code has been subjected to an extensive verification and validation program and has been applied to variety of LWR steady state and transient simulations. To enable F-COBRA-TF for industrial applications, ...

International Nuclear Information System (INIS)

Under the current design philosophy, reactor structures are to be designed to withstand large inelastic deformation caused by strong and severe ground motion. The design of the main structural elements and their connections are to be such that they always fail in ductile mode. This will ensure large energy absorption capacity of the structures under seismic excitation and avoid sudden and brittle failure of the structure. Over the years, a number of experimental investigations have been carried out on RC beam- column joints to study their behaviour and strength. However, these studies mostly pertain to small scale joints of moment resisting frame of residential buildings and commercial complexes. Information on full scale joints existing in NPP structures are scanty. Therefore, experimental programme was planned in the laboratory to construct identical large sized joints with the same reinforcement ...

Science.gov (United States)

However, market based pricing doses not apply where the pricing .... the reimbursable work, market based pricing does not apply. 040202. ...

British Library Electronic Table of Contents (United Kingdom)

Magnetic pulse welding is a solid state impact welding process, similar to explosive welding, which produces metallurgical bond by oblique high-speed impact between two metal bodies. This violent impact removes the metal surface oxide layers and then joins the two atomic level clean metal surfaces together by the incidental compression pressure. The impact velocity is at 200?400?m/s and the being welded metal surface undergoes severe plastic deformation with strain rate in the order of 106?107?s?1. The ultrafine-grained structure was observed on the welded interface. This article studied two types of similar material lap joint interfaces and the base metals were aluminum alloy 6061 and copper alloy 110. Nano-indentation testing shows that the welded interfaces have significantly greater ha...

British Library Electronic Table of Contents (United Kingdom)

Glass fiber-reinforced polymer (GFRP) reinforcing bars were used recently as main reinforcement for concrete structures. The noncorrodible GFRP material exhibits linear-elastic stress-strain characteristics up to failure with relatively low modulus of elasticity compared to steel. This raises concerns on GFRP performance in structures where energy dissipation, through plastic behavior, is required. The objective of this research project is to assess the seismic behavior of concrete beam-column joints reinforced with GFRP bars and stirrups. Two full-scale exterior T-shaped beam-column joint prototypes are constructed and tested under simulated seismic load conditions. One prototype is totally reinforced with GFRP bars and stirrups, while the other one is reinforced with steel. The experimen...

Science.gov (United States)

The progression of hip dysplasia was investigated in 116 military working dogs. Serial pelvic radiographs were graded for degree of dysplasia and degenerative joint disease (DJD). Norberg angles, angles of inclination, and joint space widths were measured. There was a significant correlation between the Norberg angle and the degree of dysplasia (p less than 0.0001). Angles of inclination and joint space width measurements did not demonstrate a correlation to canine hip dysplasia. Dysplastic dogs had a significant estimated risk for development of DJD compared to normal dogs (p less than 0.0001; odds ratio of 70.2). Dogs with normal hip conformation at 24 months of age or older did not develop moderate nor severe DJD. PMID:8875357

Science.gov (United States)

... Headquarters 5th Brugade 78th Division (Ts) ... 2nd Battalion 20th Special Forces Company B ... 29th Corps Personnel Serves Hq Joint Task Force Aug ...

UK PubMed Central (United Kingdom)

Isokinetic training and assessment of the knee joint has been the mainstay of rehabilitation, especially in patients with anterior cruciate ligament deficiency. Besides the original shin pad used, the...Full Text Available

Science.gov (United States)

Washington, DC -07/24/09 Photo: Secretary Clinton and Iraqi Prime Minister al-Maliki at HCC Bilateral; Washington, DC -07/24/09 Photo: Secretary Clinton at Joint Press...

Energy Technology Data Exchange (ETDEWEB)

The corrosion behaviour of friction stir welded (FSW) joints of AA 5083 has been compared to that of MIG welded joints. Pitting and stress corrosion cracking (SCC) resistance in 3.5% NaCl + 0.3 g/l H{sub 2}O{sub 2} and in EXCO (4 M KCl + 0.5 M KNO{sub 3} + 0.1 M HNO{sub 3}) solutions has been determined at 25 C. SCC susceptibility was evaluated by slow strain rate tests (SSRT), at a strain rate of 1 x 10{sup -6}s{sup -1}. Welds obtained by FSW technique showed a higher corrosion resistance in EXCO solution and a lower pitting tendency than the base alloy. Electrochemical measurements (corrosion potential measurements, polarization curves recording) evidenced that FSW weld was cathodic to base alloy. FSW joints were not susceptible to SCC in both test solutions, whereas MIG joints cracked in both solutions. (orig.)

Science.gov (United States)

This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development ...

UK PubMed Central (United Kingdom)

The relationships between muscle tensions, jaw motions, bite and joint forces, and craniofacial morphology are not fully understood. Three-dimensional (3-D) computer models are able to combine anatomical...Full Text Available

Science.gov (United States)

... We also toured a Trident submarine at Kings Bay, Ga. "During the weekend at the Joint Interagency Task Force Headquarters in Key West, Fla., we ...

Energy Technology Data Exchange (ETDEWEB)

The article reviews the Rothschild First Interim Report on the future of the British Coal Industry and British Coal Corporation. The report incorporates work undertaken by the Joint Working Groups set up with British Coal. The article points out various errors in the report and criticizes its conclusions.

UK PubMed Central (United Kingdom)

We describe two cases of septic arthritis occurring in association with lower urinary tract infection in elderly men. In both cases the organism isolated from both the joint and the urine was Staphylococcus...Full Text Available

Science.gov (United States)

... Volume(s) Volume(s) II Item Identification 1,2,3,4, JANAP Joint Army-Navy- 2,7 5,6,13 Air Force JIM Item Intelligence 2 Publication Maintenance ...

International Nuclear Information System (INIS)

May 2010 p. 81-84 Japan Ishizawa, Makoto JFE Steel Corporation, Tokyo

UK PubMed Central (United Kingdom)

Prophylactic knee braces are designed to prevent and reduce the severity of ligamentous injuries to the knee. Conflicting evidence is reported concerning their efficacy. The purpose of this study was...Full Text Available

Science.gov (United States)

... 2 Joint Pub. 5-0 (Dec. 26, 2006); CJCSM 3122.01A (Sept. 29, 2006, current as of Oct. 11, 2008); and CJCSM 3122.03C (Aug. 17, 2007). Page 31. ...

Science.gov (United States)

This study investigates the doctrinal guidance available to a corps headquarters if required to serve as ajoint task force headquarters and simultaneously be required to warfight the corps. The study contends that a corps being required to simultaneously ...

Science.gov (United States)

...undertake missions and tasks (on either a...Secretary of Defense to task the DoD Components...the Chairman of the Joint Chiefs of Staff any commitment of military forces assigned to the Unified... (9) Military forces employed in MSCA...approval from higher headquarters, local military...

Science.gov (United States)

The results of an investigation into the behavior of adhesively bonded doubler splices of two composite material sandwich panels are presented. The splices are studied from three approaches: analytical; numerical (finite elements); and experimental. Several parameters that characterize the splice are developed to determine their influence upon joint strength. These parameters are: doubler overlap length; core stiffness; laminate bending stiffness; the size of the gap between the spliced sandwich panels; and room and elevated temperatures. Similarities and contrasts between these splices and the physically similar single and double lap joints are discussed. The results of this investigation suggest several possible approaches to improving the strength of the sandwich splices.

British Library Electronic Table of Contents (United Kingdom)

In the last 40 years, significant advances have been made in the understanding of the neurophysiologic processes involved in the experience of trauma and pain. This knowledge, together with the rapid growth and understanding in the behavioral health sciences, has expanded to include a much better appreciation of how these fields are converging and contribute to a process called neuroplasticity. These basic mechanisms common to all patients have important implications for clinical outcome and for improving clinical practice. This article is written for clinicians who manage patients with sacroiliac joint dysfunction, a specific type of nonspecific low back pain.

Energy Technology Data Exchange (ETDEWEB)

The activities and results of a Small Business Innovation Research Phase II project entitled ''Rapid Tools for Joint Inversion and Imaging'' are presented. Research and development on three-dimensional methods to recover distributions of material property values from sparse data are reported. Innovations using artificial neural networks and extended Kalman filtering are described. The report also covers investigations on upscaling and downscaling, segmentation for data processing, and applications to ground penetrating radar and geohydraulic tomography.

Energy Technology Data Exchange (ETDEWEB)

It has become necessary to investigate the feasibility and desirability of joint coking of residues from the processing of petroleum and shale oil. Experiments have been performed on different types of feedstocks: a shale oil residue (SO) with an initial boiling point of 350/sup 0/C, obtained by thermal destruction of Bulgarian shales with a solid heat-carrier; a pyrolysis tar from the production of ethylene; extracts obtained in solvent treatment of petroleum oils, namely extracts from medium-viscosity lube distillate, viscous distillate, and residual lube stock; and asphalt obtained in deasphalting. Each of the petroleum products was blended with the SO in a 1/1 ratio.

Energy Technology Data Exchange (ETDEWEB)

The authors measured the absorption of CO{sub 2} in alkaline 0.5 M/0.5 M sodium carbonate/bicarbonate buffers containing either saccharose and sodium arsenite or saccharose and formaldehyde. Absorption enhancement increased upon increasing the concentration of either of the catalysts, but the joint action of the two was always less than the sum of their individual effects, the difference being a function of the acidities and concentrations of the catalysts and the pH of the carbonate/bicarbonate buffer solution

Energy Technology Data Exchange (ETDEWEB)

The integrity of a pipeline system is determined by its weakest links which may be the joints. Heat fusion is the most common method for joining gas distribution polyethylene (PE) piping. There are procedural, thermal, and mechanical aspects of making fusion joints. Acceptable procedural aspects, such as heater calibration and cleanliness, can be assured by rigorous training and certification of the operators. Thermal and mechanical aspects consist of specifying joining conditions such as the heater temperature, heating time, and joining pressure. In the absence of procedural errors, the strength of a fusion joint should depend on the pipe material, pipe dimensions, and the thermal and mechanical joining conditions. Socket heat fusion was studied both experimentally and analytically to determine how the strength of the joint varied with the conditions under which it was made. The standard tensile impact ...

Science.gov (United States)

Jun 6, 2011... applied first (depending upon whether the employee is exempt or non-exempt) before applying the provisions of compensatory time travel. ...

Science.gov (United States)

... DV Holliday BAE SYSTEMS Applied Technologies, IES/ITS Analysis and Applied Research 4545A Viewridge Avenue San Diego, CA 92123 phone ...

Energy Technology Data Exchange (ETDEWEB)

Heat fusion is the most common joining method for polyethylene gas distribution piping. Butt fusion was studied with the intent of relating the quality of the joint to the joining conditions. A semi-empirical approach was used. The thermofluid consequences of joining conditions such as heater temperature, heating time and joining parameter were calculated using a computer model. The model was validated by instrumented tests. The strength of the joints was gauged by destructive mechanical testing. Tensile and tensile impact tests were used. Over 150 joints were fabricated using four different polyethylene resins. Most of the data are given in GRI Report No. 88/0276.2 -- Volume 2: Technical Reference on Butt Heat Fusion Joining of Polyethylene Gas Pipes. A parameter, termed the Joining Parameter, was found to characterize the joining conditions. Of the mechanical tests parameters, the impact energy was found to have the best ...

Energy Technology Data Exchange (ETDEWEB)

Heat fusion is the most common joining method for polyethylene gas distribution piping. Butt fusion was studied with the intent of relating the quality of the joint to the joining conditions. A semi-empirical approach was used. The thermofluid consequences of joining conditions such as heater temperature, heating time and joining parameter were calculated using a computer model. The model was validated by instrumented tests. The strength of the joints was gauged by destructive mechanical testing. Tensile and tensile impact tests were used. Over 150 joints were fabricated using four different polyethylene resins. Most of the data are given in GRI Report No. 88/0276.2 -- Volume 2: Technical Reference on Butt Heat Fusion Joining of Polyethylene Gas Pipes. A parameter, termed the Joining Parameter, was found to characterize the joining conditions. Of the mechanical tests parameters, the impact energy was found to have the best ...

Energy Technology Data Exchange (ETDEWEB)

For the purpose of digging up themes of the joint research which develop the R and D in the industrial technology field in Japan to a new stage, researchers were sent to the world representing research institutes to conduct the research survey of 'Nano-structured carbon and hydrogen absorption' and 'Development of the creation technology of nano-porous materials.' As to the former, an experiment on electrochemical hydrogen absorption of carbon materials including nanotubes was conducted by researchers dispatched, but the large absorption amount was not observed. As to the latter, visits were paid to Fraunhofer Institute and the related facilities in Germany, Princeton University, MIT, GIT and Naval Research Laboratories in the U.S., Orleans University in France, AO Research Institute (bone repair study) in Switzerland, Cambridge University and University of Bristol in the U.K., etc., and the research survey was made on the ...

Energy Technology Data Exchange (ETDEWEB)

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis ...

Science.gov (United States)

Understanding the influence of interfacial structures on the nanoarchitecture mechanical properties is of particular importance for its mechanical applications. Due to a small size of constituting nanostructural units and a consequently high volume ratio of such interfacial regions, this question becomes crucial for the overall mechanical performance. Boron nitride bamboo-like nanotubes, called hereafter boron nitride nanobamboos (BNNBs), are composed of short BN nanotubular segments with specific interfaces at the bamboo-shaped joints. In this work, the mechanical properties of such structures are investigated by using direct in situ transmission electron microscopy tensile tests and molecular dynamics simulations. The mechanical properties and deformation behaviors are correlated with the interfacial structure under atomic resolution, and a geometry strengthening effect is clearly demonstrated. Due to the interlocked joint interfacial ...

Energy Technology Data Exchange (ETDEWEB)

Despite their high medical relevance, the principles of lubrication in natural joints are still unclear. It is generally accepted, that the presence of hyaluronic acid (HA), the main component of the synovial liquid, plays an important role for the low friction observed. Furthermore, it is assumed that surface active lipids participate in the lubrication. Using a model system of lipid bilayers deposited on a polyelectrolyte (PE) cushion and in contact with HA solution, we started to investigate the effects of pressure and shear forces, as experienced by natural joints, on the internal structure of the SiO{sub 2}/PE/lipid/HA interface and the bulk HA solution by neutron reflectometry (NR), complemented by in situ ellipsometry and quartz crystal microbalance (QCM-D) measurements. Only on positively charged polyelectrolyte surfaces, the successful build-up of the model system could be demonstrated. By NR, the existence of an irreversibly absorbed, ...

International Nuclear Information System (INIS)

In 576 patients quantitative scintigraphy of the sacroiliac joints and the spinal cord with "9"9"mTc-pyrophosphate was performed. 328 were patients with proven ankylosing spondylitis according to the New York criteria. 120 were patients with a clinically and roentgenologically suspected ankylosing spondylitis and 128 persons formed a healthy control group. The count rate in small regions of interest (ROI) in the sacroiliac joints, the spinal cord and the os sacrum were compared on the basis of indexes. The scintigraphic data of patients with ankylosing spondylitis were compared with the healthy control group and with the radiographic findings and radiologic staging of the disease. In a longitudinal follow-up study during 1 to 6 years these investigations were continued together with clinical and roentgenological checks. Quantitative bone scintigraphy provides characteristic indexes for ankylosing spondylitis, indicating the increased mineral ...

Energy Technology Data Exchange (ETDEWEB)

The clinical courses of heterotopic ossification (HO) as a consequence of trauma and central nervous system insults have many similarities as well as dissimilarities. Detection is commonly noted at two months. The incidence of clinically significant HO is 10%-20%. Approximately 10% of the HO is massive and causes severe restriction in joint motion or ankylosis. The most common sign and symptom are decreased range of motion and pain. The locations are the proximal limbs and joints. Sites of HO about a joint may vary according to the etiology of the HO. Roentgenographic evolution of HO occurs during a six-month period in the majority of patients. Treatment modalities include diphosphonates, indomethacin, radiation, range of motion exercises, and surgical excision. Surgical timing differs according to etiology: traumatic HO may be resected at six months; spinal cord injury HO is excised at one year; and traumatic brain injury ...

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) and the University of California, San Diego (UCSD) have taken the unprecedented step of creating a collaborative, multi-disciplinary graduate education program and associated research agenda called the Engineering Institute. The mission of the Engineering Institute is to develop a comprehensive approach for conducting LANL mission-driven, multidisciplinary engineering research and to improve recruiting, revitalization, and retention of the current and future staff necessary to support the LANL' s national security responsibilities. The components of the Engineering Institute are (1) a joint LANL/UCSD degree program, (2) joint LANL/UCSD research projects, (3) the Los Alamos Dynamic Summer School, (4) an annual workshop, and (5) industry short courses. This program is a possible model for future industry/government interactions with university partners.

International Nuclear Information System (INIS)

A novel adhesive for carbon materials composed of phenol-formaldehyde resin, boron carbide and fumed silica, was prepared. The adhesive property of graphite joints bonded by the above adhesive treated at high-temperatures was tested. Results showed that the adhesive was found to have outstanding high-temperature bonding properties for graphite. The adhesive structure was dense and uniform even after the graphite joints were heat-treated at 1500 deg. C. Bonding strength was 17.1 MPa. The evolution of adhesive structure was investigated. The results indicated that the addition of the secondary additive, fumed silica, improved the bonding performance greatly. Borosilicate phase with better stability was formed during the heat-treatment process, and the volume shrinkage was restrained effectively, which was responsible for the satisfactory high-temperature bonding performance of graphite.

British Library Electronic Table of Contents (United Kingdom)

The paper discusses the aspects of repair and retrofitting technique adopted for a damaged reinforced concrete beam-column joint specimen under cyclic loading. A specimen designed based on Indian Standard specifications with consideration of seismic load but without adopting ductile detailing (NonDuctile) was investigated under reverse cyclic loading. Then, the damaged nonductile specimen was repaired with epoxy mortar and grouted using low viscous polymer, and retrofitted using fiber reinforced plastic (FRP) wrapping in beam and column components and steel plate jacketing in joint region. The experimental results showed that the retrofitted specimen not only regained its original strength and stiffness but also has overcome the deficiencies of nonductile detailing. The present study shows...

Science.gov (United States)

This operation plan covers the period of operations from the time major elements of the joint task force are deployed in the forward area until the completion of on-site operations. It was published for planning purposes only, always subject to periodic revision and refinement as more detailed information became available. ENIWETOK-BIKINI Danger Area, as the term is used in this plan, is that area encompassing ENIWETOK and BIKINI ATOLLS and bounded by the meridians 160 deg 35' - 166 deg 16' east longitude, and by the parallels 10 deg 15' - 12 deg 45' north latitude (an area of 150 by 350 miles).

Energy Technology Data Exchange (ETDEWEB)

Young rats were given a single irradiation dose (0.5, 2, 5 or 8 Gy) to the left knee-joint. The right unexposed knee-joint served as control. The animals were decapitated 1.5, 3, 7, 14 or 30 days after the irradiation. Longitudinal bone growth in the tibial epiphysis was established using tetracycline as an intravital marker. During the first 1.5 days after irradiation with 5 and 8 Gy, the growth was slightly inhibited (6-7%). Maximum growth retardation (20%) was found 7 to 14 days after irradiation with 5 and 8 Gy. No consistent effect occurred after 0.5 and 2 Gy. Between 14 to 30 days following irradiation growth was normalized.

International Nuclear Information System (INIS)

The alloy type 'alloy 800' with its different variants is used for numerous components in high-temperature reactor (HTR) plants, e.g. for hot-gas conductors, the high-pressure part of steam generators, superheaters, steam collecting vessels and live steam conductors. This study deals with the evaluation of creep rupture tests on 28 welded joints of alloy 800 with an accumulated test duration of 410 years, with the objective to obtain quantitative information on a possible loss of strength in comparison with the unwelded material. The longest test period of an individual test amounted to 98,000 h and the analyzed test temperature range lay between 550"0 and 1000"0C. (orig./MM).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Wastenet

... This course is jointly taught between the School of Civil Engineering and the Environment and the School of Ocean and Earth Sciences. Scholarships 2 UK/EU fees only Scholarships are available for the academic year 2010/11. Awards will be given on the basis of merit. Flexible part-time study route available Back to top Home | About Us | Prospective Students |...

Science.gov (United States)

Secretary Cheney's 1990 Annual Report to the President and the Congress established the requirement for the Unified Commanders in Chief to be prepared for Third World conflict involving roles and missions requiring, 'mobile, highly ready, well equipped fo...

Energy Technology Data Exchange (ETDEWEB)

A new multipellet long-pulse plasma fueling system is in operation on JET. In the initial experimental phase, a variety of plasma density profile shapes have been produced with peak to average values ranging up to 2.5 and peak plasma density up to 1.2 )times) 10/sup 20/m/sup )minus/3). 7 refs., 4 figs

International Nuclear Information System (INIS)

The approach estimating the leak probability of flanged joint due to the destruction of fastening studs is described. The mentioned approach consists of two stages. The probability of destroying one stud is calculated at the first stage, and the probability of different combination interpositions of intact and destroyed studs is calculated at the second one. The probability calculation of leak in the area of collector cover of steam generator PGV-1000 is used as an example of developed approach

International Nuclear Information System (INIS)

This paper dealt with the identification of possible damaging mechanism of the collector of the WWER 440 steam generator, cracking of primary collectors, corrosion damage of the protective coat of the primary collector circumferential weld, cracking of breathing space in the region of blinding effect by corrosion and strain, leaking of disassembling joint of the primary collector lid and with the integrity of heat exchanging tubes.

Energy Technology Data Exchange (ETDEWEB)

The document, based on European guidelines, was jointly developed by radiation oncologists, radiation physicists and radiation technologists. It contains the aims of the guidelines, professional profiles, roles and responsibilities, personnel and equipment requirements, procedures.

International Nuclear Information System (INIS)

The tendency of welded joints from 10Kh14AG15 and 10Kh14AG9 steels to pitting corrosion under the conditions of operating blast-furnace gas purification scrubbers has been investigated. Water in scrubbers contains various quantities of chlorides and sulfates, has pH from 6 to 9 and temperature 65-75 deg. The laboratory corrosion tests have been carried out also on samples turned from the heat-affected zone (h.a.z.) of welded plates at 20 and 65 deg. Anode polarization curves have been read from the Vk corrosion potential at potential shifting rate 0.01 V/min. It is established that in most rigid conditions of scrubbers operating pitting corrosion (PC) rate of chrome-manganese nitrogen-containing steel can reach 2.5 mm/year. At high content of chlorides in water the elevated temperature and external tensile stresses intensify PC. The resistance of welded joints to PC when using welding materials on chromonickel molybdenum base is determined in ...

Energy Technology Data Exchange (ETDEWEB)

This report forms part of a joint study on a PEFC propulsion system for surface ships, summarized in a presentation to this Seminar, entitled {open_quotes}Study on a Polymer Electrolyte Fuel Cell (PEFC) Propulsion System for Surface Ships{close_quotes}, and which envisages application to a 1,500 DWT cargo vessel. The aspect treated here concerns an experiment in reducing by methanation to a level below 10 ppm the CO that is contained to around 1% in reformate gas.

Science.gov (United States)

This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development of future radiological safety plans by presenting detailed discussion of the problems and solutions arising during Operation Castle.

Energy Technology Data Exchange (ETDEWEB)

Already, MR Imaging is superior in diagnostic imaging of joints in many cases; however, there have been recent developments, which are the subjects of this paper. With gradient-echo sequences acquired in 3D technique, it is possible to produce high-resolution images of joints in acceptable scantime, because gradient-echo sequences are less time-consuming than convential SE sequences. With the acquisition of two echoes, phase difference between water and fat protons have to be considered. 3D Imaging is capable of displaying complex pathology in a superior way, which should be useful in preoperative planning. Tissue contrast is altered by fat saturation or magnetization transfer in order to achieve better conspicuity of lesions. Although diagnostic value of some of these options is not yet clear and further clinical studies are needed, they are a promising possibility for improving MR Imaging of the joints. (orig.) [Deutsch] ...

Wastenet

... This study catalysed  a more comprehensive collaborative research programme, Assessment of the durability and engineering properties of lesser known hardwood timber species for use in marine and freshwater construction, jointly funded by the Environment Agency and TRADA, and managed by H R Wallingford. Additional funding was provided by British Waterways, The Crown Estate, CETMEF (Centre d'Etudes Techniques Maritimes et Fluviales) and VolkerStevin Ltd. Timber ...

CERN Multimedia

Are you interested in beam dynamics? Do you work on the LHC injectors or CLIC or maybe feasibility studies fornew machines? Then this is for youJAS'2000: Joint CERN-Japan-JINR-Russia-US SchoolFrontiers of Accelerator Technology: High Quality Beams to be held on a river boat between St. Petersburg and Moscow 1 to 14 July 2000. For further information see eitherhttp://schools.web.cern.ch/Schools/CAS/ orhttp://www.indiana.edu/~uspas/programs/js/jas2000.html

International Nuclear Information System (INIS)

Daya Bay Nuclear Power Station is the largest joint-venture project which is also the largest commercial nuclear power plant currently under construction in China mainland. Organized and executed strictly in accordance with international standards, the Daya Bay project is seen as the first step taken by China in the development programme of large-capacity commercial nuclear power units.

Energy Technology Data Exchange (ETDEWEB)

The question about expanding the boundaries of the open pit mining method is examined. The use of methods which consider the advantages of open and underground mining operations with their joint use in horizontal and evenly dipping deposits will make it possible to objectively select the mining method, to expand the range of use of open pit mining operations in the deposits of the Far North and provide an improvement in the technical and economic indicators of mineral extraction.

Environmental Research Database

DescriptionThis project continues DEFRA's commitment to the International Programme on Chemical Safety, a joint WHO/ILO/UNEP programme. DEFRA's contribution involves preparing Environmental Health Criteira Documents (EHCs), Concise International Chemical Assessments Documents (CICADS) and input to the OECD test Guidelines Programme and gneral risk assessment guidance. Peer reviews of documents prepared through other research in the IPCS network have also been carried out,as well as attending and hosting ta [continued...

Energy Technology Data Exchange (ETDEWEB)

One of the main requirements to use Be as a candidate for plasma facing component in ITER is providing a reliable joint between Be and Cu-alloy heat sink structure. In this work authors present the results of recent activity on this way. To create Be/CuCrZr joints the unique fast e-beam brazing technology was developed in Russia. The numbers of Be/CuCrZr mock-ups were manufactured in Efremov Institute by fast e-beam brazing using Cu-Sn-In-Ni brazing alloy. These mock-ups were tested by Sandia Laboratory at the EBTS electron beam facility. The goals of the tests were to define the allowable dimensions of the armour tiles for the heat loads of more than 10 MW/m{sup 2}, to find the limit of bond strength for the Be/CuCrZr joint and response to heat loads and to estimate the life time of the brazed tiles by thermo-cyclic testing. The screening and thermal fatigue results are presented. With the aim to check the applicability of ...

International Nuclear Information System (INIS)

The paper will report the experience gained in the implementation of the national assistance projects, including the detailed assessment of the national situation compared to the ITWG Model Action Plan, the upgrading of the technical skills, the training of national experts and the joint analysis of nuclear material at ITU. The status of the work with the 13 future Member States to the European Union will also be reported on during the conference

Energy Technology Data Exchange (ETDEWEB)

The Lawrence Livermore National Laboratory (LLNL) is establishing a local chapter of the University of California Energy Institute (UCEI). In order to most effectively contribute to the Institute, LLNL sponsored a workshop on energy and environmental issues in transportation. This workshop took place in Livermore on August 10 and brought together researchers from throughout the UC systems in order to establish a joint LLNL-UC research program in transportation, with a focus on energy and environmental impacts.

Energy Technology Data Exchange (ETDEWEB)

In the context of safety assessment of radioactive waste repositories, complex radionuclide transport models covering key safety-relevant processes play a major role. In recent Swiss safety assessments, such as Kristallin-I, an important drawback was the limitation in geosphere modelling capability to account for geosphere heterogeneities. In marked contrast to this limitation in modelling capabilities, great effort has been put into investigating the heterogeneity of the geosphere as it impacts on hydrology. Structural geological methods have been used to look at the geometry of the flow paths on a small scale and the diffusion and sorption properties of different rock materials have been investigated. This huge amount of information could however be only partially applied in geosphere transport modelling. To make use of these investigations the 'PICNIC project' was established as a joint cooperation of PSI/Nagra and ...

UK PubMed Central (United Kingdom)

This study was an evaluation of the performance of self-applied, blue light, light-emitting diode therapy in the treatment of mild-to-moderate inflammatory acne on the face, concerning: 1) time to improvement...Full Text Available

International Nuclear Information System (INIS)

... Safety Institute, GRS, Cologne (Germany) INIS-UA--089 456 p. APPLIED LIFE

Energy Technology Data Exchange (ETDEWEB)

Separate entries are individually indexed.

Energy Technology Data Exchange (ETDEWEB)

Outline: Discuss far-side weld problem and phased array techniques applied. Describe laboratory work on flawed piping specimens using L- and S-wave arrays and provide synopsis of results. Discuss conclusions ofr capability of phased array as applied to austenitic welds. Research Approach: Evaluate phased arrays on unifornly-welded piping specimens. Apply best methods to non-uniform welds. Correlate acoustic responses as function of weld microstructures.

Wastenet

...authority's and schools' prospectuses Finding a school to suit your child School performance: test results and Ofsted reports Applying for a school place Once you ... Finding a school to suit your child School performance: test results and Ofsted reports Applying for a school place: admissions criteria Apply for ...

International Nuclear Information System (INIS)

There is no possibility to check any inner part at real welded joint at nuclear power station (NPS) during operation because any destructive test cannot be used. In practice there is checked surface of weld. There are used four methodical instructions for the check of real welds: 1. The visual inspection, 2. The measurement of hardness, 3. The chemical composition checking and 4. The microstructure replica analysis. It is necessary to know how these information of weld surface are in accordance with characteristics of inner parts of weld. If there is not any difference between surface weld microstructure and internal weld microstructure of experimental weld it is supposed to that there is not any difference in other measured properties of welds. If is changed structural characteristics of microstructure, it is changed also hardness, chemical analysis etc. It was observed that the microstructure of real welds is almost the same with simulated weld and also the ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the bend properties of the single-crystalline molybdenum brazed by using Mo-40%Ru alloys containing boron of 1-6 mass%Ru alloy for the improvement of the joint strength was determined. (orig.) [Deutsch] Durchgefuehrt wurde die Herstellung von Verbindungen aus einkristallinem Molybdaen. Hierbei kamen Mo-40%Ru-Legierungen mit 1 bis 6 Gew.-% Bor als Lotmaterialien zum Einsatz. Festigkeit und Duktilitaet der Verbindungen wurden mittels 3-Punkt-Biegepruefung bei Raumtemperatur und unter fluessigem Stickstoff ermittelt. Die Bruchflaechen der Proben wurden mit Hilfe eines Rasterelektronenmikroskopes untersucht. Die Ergebnisse lassen sich wie folgt zusammenfassen: Der optimale Borgehalt bezueglich Festigkeit und Duktilitaet der geloeteten Verbindung liegt bei 2 Gew.-%. Die entsprechende Probe hat bei einem Biegewinkel von 100 bei Raumtemperatur nicht versagt. Auch unter fluessigem Stickstoff zeigte diese Probe eine Festigkeit in der Groessenordnung des ...

Energy Technology Data Exchange (ETDEWEB)

The recent attempt to degassify a self contained liquid filled (SCLF) cable in Ontario Hydro is described. In September 1989, there was a high pressure alarm on one phase of a SCLF 115 kV cable circuit. The direct buried cable circuit is about 1,890 m long with two joints and was installed in 1968. Oil samples from the cable had 10 to 12% gas content with high levels of hydrogen, methane, and ethane, and very low levels of carbon monoxide, carbon dioxide, and acetylene. From these results it was concluded that the gas was generated by low energy electrical discharges and the paper insulation was not degraded. Various utilities and cable manufacturers were contacted to find if they had experienced similar problems. The cable duct oil was flushed and gasified and the successive oil samples were analyzed in order to locate the gassing site. The joints were examined and oil samples were taken through holes drilled in the cable sheath. From the test ...

International Nuclear Information System (INIS)

In this study, dissimilar welds between HP heat-resistant steel and Incoloy 800 were made with four different filler materials including: 309 stainless steel and nickel-based Inconel 82, 182 and 617. The microstructure of the base metals, weld metals and their interfaces were characterized by utilizing optical and scanning electron microscopy. Grain boundaries migration in the weld metals was studied. It was found that the migration of grain boundaries in the Inconel 82 weld metal was very extensive. Precipitates of TiC and M_2_3C_6 (M = Cr and Mo) in the Inconel 617 weld metal are identified. The necessary conditions for the formation of cracks close to the fusion line of the 309-HP joints are described. Furthermore unmixed zone near the fusion line between HP steel base metal and Inconel 82 weld metal is discussed. An epitaxial growth is characterized at the fusion line of the 309-Alloy 800 and Inconel 617-Alloy 800 joints.

Energy Technology Data Exchange (ETDEWEB)

Dissimilar metal welds between ferritic low-alloy and austenitic stainless steels commonly occur in power plant application. In order to overcome some of the problems encountered here, a trimetallic configuration using an intermediate piece (such as Alloy 800) between the austenitic and ferritic steels has been suggested. This paper describes some features of the joints between modified 9Cr-1Mo steel and Alloy 800, produced with Inconel 82/182 filler material. The joints require heat-treatment after welding and the results have shown that a treatment at 760 C for 2 h would be optimal. Although most tensile failures occurred in the weld metal the welds were found to exhibit strength properties that are at least equal to those of Alloy 800, with a tensile elongation lying between those of the two base materials. Similarly, while the weld metals are slightly less tough than the two base materials, the weld metal toughness at 120 J is still quite ...

Energy Technology Data Exchange (ETDEWEB)

Comprised of seven persons with extensive experience in the issues of nuclear waste, the Independent Review Committee (IRC) provides independent and objective review of Defense Transuranic Waste Program (DTWP) activities managed by the Joint Integration Office (JIO), formerly the Defense Transuranic Waste Lead Organization (TLO). The Committee is ensured a broad, interdisciplinary perspective since its membership includes representatives from the fields of nuclear engineering, nuclear waste transportation, industrial quality control, systems and environmental engineering and state and local government. The scope of IRC activities includes overall review of specific TLO plans, projects and activities, and technical review of particular research and development projects. The Committee makes specific suggestions and recommendations based upon expertise in the field of TRU Waste Management. The IRC operates as a consulting group, under an independent charter providing ...

International Nuclear Information System (INIS)

The 105-KE and 105-KW Fuel Storage Basins were constructed more than 35 years ago as repositories for irradiated fuel from the K East and K West Reactors. Currently, the basins contain irradiated fuel from the N Reactor. To continue to use the basins as desired, seismic adequacy in accordance with current US Department of Energy facility requirements must be demonstrated. The 105-KE and 105-KW Basins are reinforced concrete, belowground reservoirs with a 16-ft water depth. The entire water retention boundary, which currently includes a portion of the adjacent reactor buildings, must be qualified for the Hanford Site design basis earthquake. The reactor building interface joints are sealed against leakage with rubber water stops. Demonstration of the seismic adequacy of these interface joints was initially identified as a key issue in the seismic qualification effort. The issue of water leakage through seismicly induced cracks was also ...

Energy Technology Data Exchange (ETDEWEB)

A joint US/Russia program is being conducted to develop, fabricate, launch, and operate a solar dynamic demonstration system on Space Station Mir. The goal of the program is to demonstrate and confirm that solar dynamic power systems are viable for future space applications such as the International Space Station Alpha. The major components of the system include a heat receiver, a closed Brayton cycle power conversion unit, a power conditioning and control unit, a concentrator, a radiator, a thermal control system, and a Space Shuttle carrier. This paper discusses the design of the heat receiver component. The receiver comprises a cylindrical cavity, the walls of which are lined with a series of tubes running the length of the cavity. The engine working fluid, a mixture of xenon and helium, is heated by the concentrated sunlight incident on these tubes. The receiver incorporates integral thermal storage, using a eutectic mixture of lithium fluoride and calcium ...

International Nuclear Information System (INIS)

Over 300 cases of femoral neck fractures following radiotherapy for intrapelvic malignant tumor have been reported in various countries since Baensch reported this disease in 1927. In Japan, 40 cases or so have been reported, and cases of bilateral femoral neck fractures have not reached to ten cases. The authors experienced a case of 75 year-old female who received radiotherapy for cancer of the uterus, and suffered from right femoral neck fracture 3 months after and left femoral neck fracture one year and half after. As clinical symptoms, she had not previous history of trauma in bilateral femurs, but she complained of a pain in a hip joint and of gait disturbance. The pain in left femoral neck continued for about one month before fracture was recognized with roentgenogram. As histopathological findings, increase of fat marrow, decrease of bone trabeculae, and its marked degeneration were recognized. Proliferation of some blood vessels was found out, but ...

Energy Technology Data Exchange (ETDEWEB)

This work concerns the development of a methodology the objective of which is to characterize and diagnose two-phase flow regime transitions. The approach is based on the fundamental assumption that a transition flow is less stationary than a flow with an established regime. During the first time, the efforts focused on: (1) the design and construction of an experimental loop, allowing to reproduce the main horizontal two-phase flow patterns, in a stable and controlled way; (2) the design and construction of an electrical impedance probe, providing an imaged information of the spatial phase distribution in the pipe; and (3) the systematic study of the joint time-frequency and time-scale analysis methods, which permitted to define an adequate parameter quantifying the unstationarity degree. During the second time, in order to verify the fundamental assumption, a series of experiments were conducted, the objective of which was to demonstrate the correlation between ...

International Nuclear Information System (INIS)

Results of an evaluation of 18 different products that can be used as waterstops in hydraulic dams to minimize or eliminate leaks at construction joints, were discussed. The materials were tested for permeability and adherence at 23, 15 and 5 degrees C. A two-component polyurethane resin product was found to be the one that best fulfilled the evaluation criteria. It was also found that the successful injection of a borehole depends not only on selecting the product with the best performance characteristics, but also on the technique used. Hence the preparation of the resin and the pressure at which it is injected are important performance criteria. 5 refs., 6 photos, 4 figs.

Energy Technology Data Exchange (ETDEWEB)

This patent describes an automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves on the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first.

Energy Technology Data Exchange (ETDEWEB)

The survey of radiation protection programmes for transport has been jointly performed by three scientific organisations I.P.S.N. (France), G.R.S. ( Germany), and N.R.P.B. (United kingdom) on behalf of the European Commission and the pertaining documentation summarises the findings and conclusions of the work that was undertaken with the principal objectives to provide guidance on the establishment, implementation and application of radiation protection programmes for the transport of radioactive materials by operators and the assessment and evaluation of such programmes by the competent authority and to review currently existing radiation protection programmes for the transport of radioactive materials. (N.C.)

Energy Technology Data Exchange (ETDEWEB)

The power industry is moving toward the use of high-voltage transmission lines on tall, flexible towers. These towers are designed for heavier loadings than were previous towers, but the secondary effects of tower displacement tend to be ignored in the present day tower analysis. This paper examines the secondary effects from the large displacement of flexible towers, reviews the secondary stresses arising from joint rigidity and member continuity, and examines the reliability of tower strength predicted by the ASCE design guidelines. More realistic tower test acceptance criteria and a more reliable tower design methodology are suggested.

International Nuclear Information System (INIS)

At the importance increase of UT (ultrasonic testing) with the application of rules on fitness-for-service for nuclear power plants, JAPEIC (Japan power engineering and inspection corporation) started education training for defect detection and sizing technique. Weld joints specimen with EDM (Electro-Discharged Machining) notches, fatigue cracks and intergranular stress corrosion cracks were tested and practiced repeatedly based on a modified ultrasonic method and the defect size measuring accuracy of the trainees was surely improved. Results of the blind test confirmed effectiveness of education training. (T. Tanaka)

Energy Technology Data Exchange (ETDEWEB)

This paper presents a decision approach, and associated computer software tools, for prioritizing and selecting among technology development activities. The approach elicits and then summarizes technology development preferences from stakeholders, and then integrates preferences into a set of funding recommendations. By formalizing the technology review process, the decision approach builds consensus and clarifies the basis for final budget decisions. The software development was conducted jointly by Pacific Northwest Laboratory and Decisions Science Associates, Incorporated. The Underground Storage Tank Integrated Demonstration funded the task; however, the approach should also be valuable to the US Department of Energy Office of Technology Development, the Office of Waste Management, and the Office of Environmental Restoration.

Energy Technology Data Exchange (ETDEWEB)

An advanced video system has been assembled from commercially available equipment to support the real-time neutron radiography facility established jointly by the University of Virginia Department of Nuclear Engineering and Engineering Physics, and the Philip Morris Research Center. A schematic diagram of the equipment used for real-time neutron radiography is presented. To obtain quantitative density measurements with this system, several modifications of both hardware and image processing software were required. After implementation of these changes, the system was capable of determining material densities by measuring the degree of neutron attenuation.

Energy Technology Data Exchange (ETDEWEB)

The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.

Energy Technology Data Exchange (ETDEWEB)

The grain boundary crystallographic misorientations of magnetic-pulse-welded (MPW) aluminum alloy (AA) 6061-T6 in linear and tubular configurations were examined using the electron backscattered diffraction (EBSD) technique. A refined structure of heavily deformed grains with higher grain boundary angles was observed in linear welds. Significant spalling was observed away from the joints, in the interior of tubular welds. The results show the complex interaction of shock waves with the materials during this impact welding process.

Energy Technology Data Exchange (ETDEWEB)

The Joint European Torus (JET) fusion machine is the only device capable of operation with tritium (as fuel) and Be (as plasma facing component), what makes it best suited to study ITER relevant issues. A large variety of activities are performed within the JET Fusion Technology Task Force. In this paper, some topics such as erosion/deposition and material transport, flakes characterization and detritiation techniques are highlighted. Recent results obtained using a pumping cryo-panel and on plasma facing component characterisation are given. Finally, issues that will be addressed in the forthcoming JET work-programme are presented, such as a beryllium main wall for JET and in-situ laser detritiation. (authors)

Energy Technology Data Exchange (ETDEWEB)

The shot peening of the outer surface of Alloy 800 is proposed by the steam generator supplier in order to increase the stress corrosion cracking resistance of the tubes. The benefits and drawbacks of such a treatment are evaluated, focusing on the main concern i.e. a possible enhanced tendency of stress corrosion cracking at the transition of the expanded tube-to-tubesheet joint. Stress corrosion tests as well as residual stresses measurements demonstrate no significant difference between peened and unpeened tubes at that location. The other concerns such as stability of the compressive stresses, increased risk of pitting or intergranular attack and pollution of the secondary circuit by fragmented beads appear the as minor concerns.

Energy Technology Data Exchange (ETDEWEB)

Friction stir welding of dissimilar formed Mg alloys(AZ31/AZ91) was successfully carried out at the limited welding conditions. In a sound joint, SZ was mainly consisted of AZ31 Mg alloy which was located the retreating side. Dynamic recrystallization and grain growth occurred and {beta} intermetallic compounds of AZ 91 Mg alloy was not observed in SZ. BM had a higher hardness than that of the weld zone. The fracture location was not weld zone but BM of the AZ91 Mg alloy in tensile test. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The authors trace the early history of nuclear power regulation in the US. Focusing on the Atomic Energy Commission, they describe the role of other groups that figured in the development of regulatory policies, including the Congressional Joint Committee on Atomic Energy, other federal agencies, state governments, the nuclear industry, and scientific organizations. They consider changes in public perceptions of and attitudes toward atomic energy and the dangers of radiation exposure. The basic purpose of the book is to provide the Nuclear Regulatory Commission and the general public with information on the historical antecedents and background of regulatory issues so that there will be continuity in policy decisions. The book concludes with an annotated bibliography of selected references. 19 figures.

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionTo determine the effects of water penetration on the burst strength of filament wound composite pipes which have been damaged by impact and then subjected to long term pressurisation with sea water. ~%~ To monitor and characterise the damage and effects of sea water penetration using ultrasonic NDT. To determine the burst strength of bonded composite pipe joints with and without defects and to see whether the defects can be detected using ultrasonic NDT. [continued...

Energy Technology Data Exchange (ETDEWEB)

The susceptibility of CHN35VT-VD and 08CH18N10T stainless steels to stress corrosion cracking in water environment, simulating water solution found in threaded holes, was investigated using rising load line displacement tests of precracked C(T) specimens. To judge the role of oxidant on stress corrosion cracking of both stainless steels, the effect of dissolved oxygen content (fully deaerated water, water aerated at the beginning of the test) was studied. 7 refs.

International Nuclear Information System (INIS)

The UK fully supports the objective of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management to achieve and maintain a high level of safety worldwide in spent fuel and radioactive waste management, through the enhancement of national measures and international co-operation, including where appropriate, safety-related co-operation. The UK's Health and Safety Executive, through its Nuclear Safety Directorate (NSD), has been committed to the Convention since the initial negotiations to set up the Convention and provided the president of the first review meeting in 2003. It would be wrong of any nation to believe that they have all the best solutions to managing spent fuel and radioactive waste. The process of compiling reports for the Convention review meetings provides a structured process through which every contracting party can review its provisions against a common set of standards and identify for itself ...

Energy Technology Data Exchange (ETDEWEB)

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis ...

Science.gov (United States)

Purpose: Assess the feasibility of using NASA satellite data to monitor persistent saltwater intrusion in coastal marshes. End User: USGS National Wetlands ...

International Nuclear Information System (INIS)

Russian (1972). USSR Prokof'eva, MS (no.188) p. 217-222. age

UK PubMed Central (United Kingdom)

BackgroundCharacterization of the innate immune repertoire of extant cnidarians is of both fundamental and applied interest - it not only provides insights into the basic immunological...Full Text Available

International Nuclear Information System (INIS)

1973. 49 p. United States Belanger, BC USAEC Division of Applied

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... 10 TIN TELLURIDE Preparation of Tin Telluride Single Crystals ..... 12 ... TIN TELLURIDE Preparation of Tin Telluride Single Crystals ...

UK PubMed Central (United Kingdom)

A new technique to monitor light diffraction patterns electrically is applied to frog semitendinosus muscle fibers at various levels of stretch. The intensity of the diffraction lines, sarcomere length...Full Text Available

Science.gov (United States)

Geometra'. Scrape Geom- ett_,. Used By: Theoretical. FEM Weight. Apply Linear Delta ...... that the FEM is geometri- cally linear, the differences between ...

UK PubMed Central (United Kingdom)

Congruence is a broadly applied notion in evolutionary biology used to justify multigene phylogeny or phylogenomics, as well as in studies of coevolution, lateral gene transfer, and as evidence for...Full Text Available

Science.gov (United States)

consider applying the requirements of MIL-STD-2073-1. 5.2.5. Sustainability. Because of the design control the. Government has had over. XIL-SPEC designs, ...