Energy Technology Data Exchange (ETDEWEB)

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, an improved version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multicomponent gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to ...

Science.gov (United States)

No Abstract Available

Science.gov (United States)

No Abstract Available

Science.gov (United States)

... values and unless special precautions and equipment are used, it would be very difficult to service and maintain operational jet-fuel systems with ...

Science.gov (United States)

... Descriptors : *JET ENGINE FUELS, *AQUATIC ORGANISMS, *AVIATION FUELS, *TOXICITY, HEALTH, SMOKE SCREENS, WIND, WATER ...

Science.gov (United States)

This study examined the effect of sulfur-containing compounds on the storage stability of Jet A

Science.gov (United States)

Approximately 62,000 lbs Fuel Load: 58,000 lbs. Type Fuel: JP4, JP5, JP8, JET A, JET A-1, JET B Standard Fuel Burn: 4500 - 6000 lbs/hr depending on altitude and airspeed Maximum...

Science.gov (United States)

Two hundred eleven references from the period 1951 to 1978 are reviewed in this survey of literature on the thermal stability of jet aircraft fuels.

Science.gov (United States)

NASA 1996 STTR Phase I. Proposal Number: 960022. Project Title: ADVANCED INTERNAL COMBUSTION ENGINE USING JET FUELS FOR LIGHT AIRCRAFT ...

Norwegian Open Research Archives (NORA)

Full Text Available

Science.gov (United States)

No Abstract Available

Energy Technology Data Exchange (ETDEWEB)

We developed a surrogate mixture model to represent the physical properties of a coal-derived liquid fuel using only information obtained from a gas chromatography-mass spectrometry analysis of the fuel and a recently developed 'advanced distillation curve'. We then predicted the density, speed of sound, and viscosity of the fuel and compared them to limited experimental data. The surrogate contains five components (n-propylcyclohexane, trans-decalin, {alpha}-methyldecalin, bicyclohexane, and n-hexadecane), yet comparisons to limited experimental data demonstrate that the model is able to represent the density, sound speed, and viscosity to within 1, 4, and 5%, respectively. 102 refs., 2 figs., 5 tabs.

Energy Technology Data Exchange (ETDEWEB)

A transition from petroleum~derived jet fuels to blends with Fischer-Tropsch (F~T) fuels, and ultimately fully synthetic hydro-isomerized F-T fuels has raised concern about the fate of plasticizers in nitrile-butadiene rubber a-rings that are contacted by the fuels as this transition occurs. The partitioning of plasticizers and fuel molecules between nitrile a-rings and petroleum-derived, synthetic, and additized-synthetic jet fuels has been measured. Thermal desorption of o-rings soaked in the various jet fuels followed by gas chromatographic analysis with a mass spectrometric detector showed many of the plasticizer and stabilizer compounds were removed from the o-rings regardless of the contact fuel. Fuel molecules were observed to ...

Science.gov (United States)

The goal of this research program has been to add to our understanding of the breakup of molten fuel jets penetrating reactor coolant. Easily handled working fluids are used to simulate fuel jet breakup, so that detailed observations may be obtained from a relatively large number of experiments. The tools used for observing this behavior are high speed notion picture photography, Flash X-radiography, and X-ray cine. Jet breakup lengths are determined from motion pictures; the mechanisms by which the jets are fragmented may be inferred from radiographs.

International Nuclear Information System (INIS)

We provide a detailed overview of an on-going, multinational test programme that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolised materials plus volatilised fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy/density device. The programme participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research programme. Sandia National Laboratories has the lead role for conducting this research programme; test programme support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. We provide a summary of the overall, multiphase ...

International Nuclear Information System (INIS)

The authors provide a detailed overview of an on-going, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy-density device. The program participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research program. Sandia National Laboratories has the lead role for conducting this research program; test program support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. The authors provide a summary of the overall, ...

Energy Technology Data Exchange (ETDEWEB)

Experiments in a homogeneous charge compression ignition (HCCI) engine have been conducted with four gasoline surrogate fuel blends. The pure components in the surrogate fuels consisted of n-heptane, isooctane, toluene, ethanol and diisobutylene and fuel sensitivities (RON-MON) in the fuel blends ranged from two to nine. The operating conditions for the engine were p{sub in}=0.1 and 0.2 MPa, T{sub in}=80 and 250 C, {phi}=0.25 in air and engine speed 1200 rpm. A semidetailed chemical kinetic model (142 species and 672 reactions) for gasoline surrogate fuels, validated against ignition data from experiments conducted in shock tubes for gasoline surrogate fuel blends at 1.0{<=} p{<=}5.0MPa, 700{<=} T{<=}1200 K and {phi}=1.0, was successfully used to ...

Science.gov (United States)

The Ames autotracking airborne sun photometer was used to investigate the spectral depth between 380

Science.gov (United States)

The past three years of work for the Air Force Office of Scientific Research has resulted in the development of a congenic mouse model of JP-8 jet fuel exposure, the role of substance P in the JP-8 jet fuel-induced lung injury process, and development of ...

International Nuclear Information System (INIS)

To clarify the effects of the principal factors that govern the thermal fragmentation of a molten metallic fuel jet in the course of fuel-coolant interaction, which is important in evaluating the sequence of core disruptive accidents (CDAs) for metallic fuel fast reactors, basic experiments were carried out using molten metallic fuel simulants (copper and silver) and a sodium pool.Fragmentation of a molten metal jet with a solid crust was caused by internal pressure produced by the boiling of sodium, which is locally entrapped inside the jet due to hydrodynamic motion between the jet and the coolant. The superheating and the latent heat of fusion of the jet are the principal factors governing this type of thermal fragmentation. On the other hand, the effect of the initial sodium temperature is ...

Science.gov (United States)

activities, including the combustion of diesel fuel in heavy-duty vehicles and jet fuel in aircrafts. Current details on emissions from the transportation and other...

Science.gov (United States)

and used to reduce or replace petroleum-based transportation fuel, heating oil or jet fuel). In addition, this rule includes a new regulatory provision establishing a...

Science.gov (United States)

from a military fuel storage facility released about 80,000 gallons of kerosine-based jet fuel. Immediate and extensive recovery measures managed to contain the spill, but...

Energy Technology Data Exchange (ETDEWEB)

We provide a detailed overview of an ongoing, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high energy density device, HEDD. The program participants in the U.S. plus Germany, France, and the U.K., part of the international Working Group for Sabotage Concerns of Transport and Storage Casks, WGSTSC have strongly supported and coordinated this research program. Sandia National Laboratories, SNL, has the lead role for conducting this research program; test program support is provided by both the U.S. Department of Energy and Nuclear Regulatory Commission. WGSTSC partners need this research to better understand potential ...

Science.gov (United States)

A technical review is presented of experiment activities and state of knowledge on air-borne, radiation source terms resulting from explosive sabotage attacks on spent reactor fuel subassemblies in shielded casks. Current assumptions about the behavior of irradiated fuel are largely based on a limited number of experimental results involving unirradiated, depleted uranium dioxide ''surrogate'' fuel. The behavior of irradiated nuclear fuel subjected to explosive conditions could be different from the behavior of the surrogate fuel, depending on the assumptions made by the evaluator. Available data indicate that these potential differences could result in errors, and possible orders-of-magnitude overestimates of aerosol dispersion and potential health effects from sabotage attacks. Furthermore, it is ...

Science.gov (United States)

A process and apparatus for the production of coke, asphalt and jet fuel m a feed of fossil fuels containing volatile carbon compounds therein is disclosed. The process includes the steps of pyrolyzing the feed in an entrained bed pyrolyzing means, separating the volatile pyrolysis products from the solid pyrolysis products removing at least one coke from the solid pyrolysis products, fractionating the volatile pyrolysis products to produce an overhead stream and a bottom stream which is useful as asphalt for road pavement, condensing the overhead stream to produce a condensed liquid fraction and a noncondensable, gaseous fraction, and removing water from the condensed liquid fraction to produce a jet fuel-containing product. The disclosed apparatus is useful for practicing the foregoing process. the process provides a useful method of mass producing and jet ...

Science.gov (United States)

There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth ...

Science.gov (United States)

An experimental study of H-air counterflow diffusion flames (CFDFs) is reported. Coaxial tubular

Science.gov (United States)

star formation. To either side of the center, a small bar of dust and gas is helping to fuel the new stars. NASA's Jet Propulsion Laboratory, Pasadena, Calif., manages the...

Science.gov (United States)

this, however, was a real environmental threat since various drums containing jet fuel, Bunker C, diesel and other petroleum derivatives were on fire. The CAPECO...

Energy Technology Data Exchange (ETDEWEB)

In order to predict the effect of a fuel-coolant interaction after a hypothetical core-melt-down accident, a phenomenological model has been developed to describe the thermal and hydrodynamic behavior of a high-temperature molten jet when it interacts with saturated or subcooled water in a film boiling regime. The mechanisms of jet-material erosion were analyzed by Kelvin-Helmholtz instabilities on the coherent column and by boundary layer stripping on the leading edge. The heat transfer coefficient, vapor-film thickness, and net steam generation, all of which strongly affect the jet-breakup behavior, were solved analytically. It was found that the jet breakup (or erosion) depends strongly on the steam generation from the jet/water interaction. The jet-breakup length (i.e., penetration distance) was found to be sensitive to the initial ...

International Nuclear Information System (INIS)

This multinational, multi-phase spent fuel sabotage test program is quantifying the aerosol particles produced when the products of a high energy density device (HEDD) interact with and explosively particulate test rodlets that contain pellets of either surrogate materials or actual spent fuel. This program has been underway for several years. This program provides data that are relevant to some sabotage scenarios in relation to spent fuel transport and storage casks, and associated risk assessments. The program also provides significant technical and political benefits in international cooperation. We are quantifying the Spent Fuel Ratio (SFR), the ratio of the aerosol particles released from HEDD-impacted actual spent fuel to the aerosol particles produced from surrogate materials, measured under closely matched test conditions, in a ...

Science.gov (United States)

Persistently high concentrations of carbon monoxide and low-altitude ozone in the air of the Nation's major urban centers led Congress in the 1990 Clean Air Act Amendments to mandate changes to the composition of gasoline and diesel fuel. Those gasoline c...

Energy Technology Data Exchange (ETDEWEB)

The impingement of a fluid jet onto a surface has broad applications across many industries. Within the UK nuclear industry, during the final stages of fuel reprocessing, impinging fluid jets are utilised to mobilise settled sludge material within storage tanks and ponds in preparation for transfer and ultimate immobilisation through vitrification. Despite the extensive applications of impinging jets within the nuclear and other industries, the study of two-phase, solid loaded, impinging jets is limited, and generally restricted to computational modelling. Surprisingly, very little fundamental understanding of the turbulence structure within such fluid flows through experimental investigation is found within the literature. The physical modelling of impinging jet systems could successfully serve to aid computer model validation, determine operating requirements, ...

International Nuclear Information System (INIS)

One of several methods to build YSZ electrolyte of SOFC is plasma spraying. This system heats particle to a melting point and then pushing them into target and forming a deposition. This paper presents heating studies of YSZ particle in plasma jet. By simple model it is shown that the required time such those YSZ particle with grain size of 50 ?m to be melt is around 12 x 10-4 second. (author)

Science.gov (United States)

to end statewide burn ban 09/28/2011 - Commissioner's statement on $80 million biomass to jet fuel award to UW and WSU Media Center | View All News Meetings & Events Saturday Oct...

Energy Technology Data Exchange (ETDEWEB)

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was ...

Energy Technology Data Exchange (ETDEWEB)

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key ...

International Nuclear Information System (INIS)

To clarify the fragmentation mechanism of a molten metallic fuel jet in a sodium pool under high-ejection-velocity conditions that correspond to the medium- and high-burnup conditions in the metallic fuel core of liquid-metal-cooled fast breeder reactors, a series of experiments with molten copper as a metallic fuel simulant and a sodium pool was carried out. Under low-ejection-velocity conditions in the range of an ambient Weber number (Wea) a ? 200, the size of the fragments is confirmed to be almost independent of the initial superheating of the jet. Furthermore, the size of the fragments agrees well with that evaluated using the Rayleigh-Taylor instability model, in which the fragment size is assumed to be equal to half the fastest growing wavelength. This result is qualitatively consistent with the characteristics that the molten jet column with large ...

Energy Technology Data Exchange (ETDEWEB)

Due to the increasingly stricter regulations for deep reduction of fuel sulfur content, development of new deep desulfurization processes for liquid transport fuels has become one of the major challenges to the refining industry and to the production of hydrocarbon fuels for fuel cell applications. The sulfur compounds in the current transport fuels corresponding to the S level of 350-500 ppm account for only about 0.12-0.25 wt % of the fuel. The conventional hydrotreating approaches will need to increase catalyst bed volume at high-temperature and high-pressure conditions for treating 100 % of the whole fuel in order to convert the fuel mass of less than 0.25 wt %. In the present study, we are exploring a novel adsorption process for desulfurization at low temperatures, which can effectively reduce the sulfur content in ...

Energy Technology Data Exchange (ETDEWEB)

A computationally efficient dynamic adaptive chemistry (DAC) scheme is described that permits on-the-fly mechanism reduction during reactive flow calculations. The scheme reduces a globally valid full mechanism to a locally, instantaneously applicable smaller mechanism. Previously we demonstrated its applicability to homogeneous charge compression ignition (HCCI) problems with n-heptane [L. Liang, J.G. Stevens, J.T. Farrell, Proc. Combust. Inst. 32 (2009) 527-534]. In this work we demonstrate the broader utility of the DAC scheme through the simulation of HCCI and shock tube ignition delay times (IDT) for three gasoline surrogates, including two- and three-component blends of primary reference fuels (PRF) and toluene reference fuels (TRF). Both a detailed 1099-species mechanism and a skeletal 150-species mechanism are investigated as the full mechanism to explore the impact of fuel complexity on the DAC ...

Energy Technology Data Exchange (ETDEWEB)

The authors synthesized a number of esters of stearic acid with polyhydric alcohols and ran comparative tests on aliphatic alcohols to determine their effects on the antiwear properties of the fuel. They conclude that the differences in effectiveness in improving the lubricity by the use of aliphatic alcohols and the full and partial esters of polyhydric alcohols and stearic acid can be explained by the presence of hydroxyl and ester groups close to each other in partial esters. This is reflected in the higher polarity of the partial esters, a higher rate of adsorption, and a stronger bonding of the adsorbed layer to the metal surface.

Energy Technology Data Exchange (ETDEWEB)

The performance of the new combustor was tested. Experiments showed that this combustor has superior insulating quality than the previous one. Measured radial concentrations indicated uniform distribution of the primary fuel (coal) inside the fire tube resulting in reasonably flat concentration profiles. However, measured radial concentrations after the addition of the reburn fuel showed uneven distribution of the fuel resulting in parabolic concentration profiles, an indication of insufficient mixing in the reburn zone. In order to study mechanisms of nitrogenous species destruction in the reburn zone, it is necessary to achieve adequate mixing if the assumption of one dimensional plug flow behavior is to be valid. Thus, it became necessary to modify the injector design and the injection mode of the reburn fuel to achieve an adequate level of mixing which is the focus of this report. The results show ...

Science.gov (United States)

>The causes and implications of the impeading shortages of gasoline, heating oil, diesel fuel, jet fuel, and electricity were investigated at the May 3, 1973 hearings. Discussions and related data were presented on short-term fuel shortages and their effects on the electric utilfties and the present situation in the regulated energy industries and its effects on energy R&D. The statement of the national oil lobbers council is presented in an appendix. (MCW)

British Library Electronic Table of Contents (United Kingdom)

Strut lattice structures of reaction-bonded silicon infiltrated silicon carbide ceramics (RB-SiSiC) for air-fuel mixture formation and for nonstationary lean-burn under pressure applications were fabricated. The lattice design with a high porosity >80% was shaped by indirect three-dimensional printing. It was shown that pre-ignition processes in the porous reactor are much faster than in a free combustion, especially at lower temperatures. Interaction of high velocity diesel jets with cylindrical strut ligaments of the SiSiC lattice structure offers a new possibility for quick and efficient fuel distribution (multi-jet splitting) in space.

British Library Electronic Table of Contents (United Kingdom)

A detailed chemical kinetic reaction mechanism is developed for primary reference fuel mixtures of n-hexadecane and 2,2,4,4,6,8,8-heptamethyl nonane for diesel cetane ratings. The mechanisms are constructed using existing rules for reaction pathways and rate expressions developed previously for the primary reference fuels for gasoline octane ratings, n-heptane and iso-octane. These reaction mechanisms are validated by comparisons between computed and experimental results for shock tube ignition and for oxidation under jet-stirred reactor conditions. The combined kinetic reaction mechanism contains the submechanisms for the primary reference fuels for diesel cetane ratings and submechanisms for the primary reference fuels for gasoline octane ratings, all in one integrated large kinetic reac...

Science.gov (United States)

This paper explores effects of differential diffusion in nonpremixed turbulent jet flames. Pulsed Raman scattering spectroscopy is used to measure temperature and species concentrations in chemically reacting jets of H{sub 2}/CO{sub 2} into air, over a range of jet Reynolds numbers from 1,000 to 30,000 based on cold jet fluid properties. Results show significant effects of differential diffusion at all jet Reynolds numbers considered. Differential diffusion between H{sub 2} and C0{sub 2} produces differences between the hydrogen element mixture fraction ({xi}{sub H}) and the carbon element mixture fraction ({xi}{sub c}). The greatest effects occur on the rich side of stoichiometric, where {xi}{sub H} is observed to be smaller than {xi}{sub C} at all Reynolds numbers. Differential diffusion between H{sub 2} and H{sub 2}O creates a net flux of hydrogen element toward the ...

Energy Technology Data Exchange (ETDEWEB)

The characteristics of diesel fuel jet atomization in carburetors depend on dynamic viscosity (v) density (d) and surface tension (st) of fuel, grouped in the combined functions v/d; st/v and st/d. Values of these combined functions for binary mixtures of a farm diesel fuel with a crude vegetable oil (sunflower, soybean, cotton and foot-cake olive oils) as well as with a used frying olive oil, are calculated. Three different diesel fuels have been studied. Combined function values of these mixtures are influenced by the characteristics of their diesel fuel. Mixtures containing less than 24% of any studied crude oils show kinematic viscosity values at 40 degrees C not exceeding 5.8 squared millimeters/s. This value is the higher limit for typical United States farm diesel fuels, according to specifications of the Cummins Engine Company. ...

International Nuclear Information System (INIS)

Morphology of castellated Be tiles from the belt limiter exposed to the JET plasma for 56,000 s was examined on both sides of castellated grooves, on plasma-facing and side surfaces of the tiles. The essential results are (i) deuterium retention in the castellated grooves and in other locations is associated with co-deposition of carbon; (ii) the decay length of deposition in the castellation is around 1.5 mm; (iii) no deuterium is detected in bulk Be; (iv) bridging of gaps by molten beryllium occurred but gaps were not filled with Be; (v) on side surfaces of the tiles the formation of BeO layer was detected at a distance of 20 mm and more from the plasma-facing surface. The consequences for a long-term operation of a reactor-class device with several different plasma-facing materials are addressed.

Energy Technology Data Exchange (ETDEWEB)

A mathematical model was developed to simulate the combustion process of a direct injection diesel engine. The model considers the key features of such a combustion process; namely fuel droplet evaporation, spray formation, mixing, ignition of heterogeneous burning of the fuel. To model mixing, great emphasis was placed on treating both large and small scale aspects of mixing, the model divides the combustion chamber into three distinct regions of air, fuel spray, and a turbulent plume that is formed once ignition occurs. The fuel spray itself is considered to be composed of multiple zones, which in turn are made of cells of equal mass and of different thermodynamic states. Micromixing of the fuel and air cells, within each zone of the jet and the turbulent plume, is then achieved by utilizing the concept of Monte Carlo stochastic coalescence dispersion ...

International Nuclear Information System (INIS)

The progression of hypothetical core disruptive accidents in metallic fuel fast breeder reactors is strongly affected by the fragmentation of molten metallic fuels due to the molten fuel-coolant interaction (FCI). As a basic study of FCI, the present paper focuses on the fragmentation of a single molten copper droplet with mass from 1 to 5 g, which penetrated a sodium pool at instantaneous constant interface temperatures (Ti) from 995 to 1,342degC. Intensive fragmentation of a single molten copper droplet was clearly observed even if Ti values are below the melting point (1,083degC) of copper besides the higher Ti range. The intensive fragmentation shows that the mass median diameters (Dm) of copper droplets with a fivefold difference in mass or the same mass have little difference, i.e., they are nearly the same. Under the lower Ti condition, the Dm data of droplet fragments of both the same and different masses scatter ...

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas ...

Energy Technology Data Exchange (ETDEWEB)

The present work reports an experimental study on the behavior of a jet flame surrounded by a shroud of combustion air. Measurements focussed on the flame length and the emissions of NO{sub x}, total unburned hydrocarbons, CO{sub 2}, and O{sub 2}. Four different fuel flow rates (40.0, 78.33, 138.33, and 166.6 cm/s), air flow rates up to 2500 cm{sup 3}/s and four different air injector diameters (0.079 cm, 0. 158 cm, 0.237 cm, and 0.316 cm) were used. The shroud of combustion air causes the flame length to decrease by a factor proportional to 1/[p{sub a}/p{sub f} + C{sub 2}({mu}{sub a}Re,a/{mu}{sub f}Re,f){sup 2}]{sup {1/2}}. A substantial shortening of the flame length occurred by increasing the air injection velocity keeping fuel rate fixed or conversely by lowering the fuel flow rate keeping air flow rate constant. NO{sub x} emissions ranging from 5 ppm to 64 ppm were observed and the emission of ...

Energy Technology Data Exchange (ETDEWEB)

The application of foam in dealing with underground fire is well known due to its smothering action by cutting off air feed to burning fuel as well as acting as coolant. Besides plugging air feed to fire, water could be virtually reached to the fire affected areas much beyond the jet range as underground galleries with low roof restrict jet range of water. This method also enables a closer approach of a fire fighting team by isolating the toxic gases and smoke with a foam plug. The paper describes the development of high expansion foam composition and its application technology in order that foam plug method can be suitably utilized for combating mine fires in India. Three compositions were recommended for generation of high expansion foam: (a) 0.5% sodium/ammonium lauryl sulphate, 0.15 to 0.2% sodium carboxy methyl cellulose, 0.1% booster; (b) 0.5% sodium/ammonium lauryl sulfate, 0.12 to 0.15% alkaline solution of gum ...

Energy Technology Data Exchange (ETDEWEB)

In order to develop modern two-stroke engines with low fuel consumption, respectively with low exhaust emissions, two alternative development areas -- the mixture formation and the scavenging system -- have been correlated. For a satisfying mixture formation without fuel losses by scavenging, the direct injection seems to be one of the best solution for the high speed two-stroke engine of the future. On the other hand the modern development of two-stroke scavenging systems shows a large field of application and improvement methods of cross and loop scavenging. Based on the specific optimization factors of the injection system, respectively of the scavenging system, the aim off this common work of the Universities of Pisa and Zwickau is to correlate both the optimization fields in an advantageous mixture formation process. The principal elements of this correlation are the design of the combustion chamber, the position of the injection nozzle, ...

Energy Technology Data Exchange (ETDEWEB)

This bibliography includes over 600 references (with abstracts) on all aspects of waterjet cutting and cleaning. The references are listed under the following chapter headings: fluid mechanics of jets; jet impact; equipment; jet cleaning; jet cutting; civil engineering; mining and tunnelling; precision cutting; underwater; safety; and bibliographies. Separate author and corporate source indexes are provided.

Energy Technology Data Exchange (ETDEWEB)

This report describes experiments to determine whether a wiped film evaporator (WFE) might be used to concentrate low-level liquid radioactive waste (LLLW). Solutions used in these studies were surrogates that contain no radionuclides. The compositions of the surrogates were based on one of Oak Ridge National Laboratory`s (ORNL`s) Melton Valley Storage Tanks (MVSTs). It was found that a WFE could be used to concentrate LLLW to varying degrees by manipulating various parameters. The parameters studied were rotor speed, process fluid feed temperature and feed rate, and evaporator temperature. Product consistency varied from an unsaturated liquid to a dry powder. Volume reductions up to 68% were achieved. System decontamination factors were consistently in the range of 10{sup 4}.

Science.gov (United States)

An experimental investigation of heat transfer characteristics for various configurations of air jets impinging on the leading edge inner surface of a gas turbine blade wall is presented. Three configurations were investigated, namely a slot jet, a round ...

Science.gov (United States)

In the late 1980's, the traditional threat of anonymous break-ins to networked computers was joined by viruses and worms, multiplicative surrogates that carry out the bidding of their authors. Technologies for authentication and secrecy, supplemented by good management practices, are the principal countermeasures. Four articles on these subjects are presented.

UK PubMed Central (United Kingdom)

BackgroundSurrogate immunologic markers for natural and vaccine-mediated protection against tuberculosis (TB) have not been identified.MethodsHIV-infected...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundTraditionally in pediatric HIV, the CD4+ T-lymphocyte percent is used in monitoring disease progression due to the variability in absolute CD4+ T-lymphocyte...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The two-dimensional Eulerian hydrodynamic code 2DE with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities ...

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

In order to clarify a mechanism of melt-jet breakup and fragmentation entirely different from the mechanism of stripping, a series of experiments were carried out by using molten tin jets of 100 grams with initial temperatures from 250degC to 900degC. Molten tin jets with a small kinematic viscosity and a large thermal diffusivity were used to observe breakup and fragmentation of melt jets enhanced thermally and hydrodynamically. We observed jet columns with second-stage large-scale structures generated by the coalescence of large-scale structures recognized in the field of fluid mechanics. At a greater depth, the segmentation of jet columns between second-stage large-scale structures and the fragmentation of the segmented jet columns were observed. It is reasonable to consider that the segmentation and the fragmentation of ...

Energy Technology Data Exchange (ETDEWEB)

A parametric experimental investigation of an 85 millimeter bore angular contact ball bearing running in RP-1 fuel was performed at speeds of 10,000 to 24,000 rpm. Thrust loads were varied from 4450 to 17,800 Newtons (1000 to 4000 lbs.). Radial loads were varied from 1335 to 13,350 Newtons (300 to 3000 lbs.). RP-1 lubrication for the bearing was provided through a stationary jet ring located adjacent to the test bearing outer ring. Increases in both the thrust and radial loads resulted in increased bearing temperature, while increases in shaft speed resulted in much more dramatic increases in bearing temperature. These trends are typical for ball bearings operating under these types of conditions. Results are given for outer ring temperatures of the test bearing at the various test conditions employed. In addition, the heat energy removed from the bearing by the RP-1 was determined by measuring the increase in temperature as the RP-1 passed ...

Energy Technology Data Exchange (ETDEWEB)

Reaction Engineering International (REI) has established a project team of experts to develop a technology for combustion systems which will minimize NO x emissions and minimize carbon in the fly ash. This much need technology will allow users to meet environmental compliance and produce a saleable by-product. This study is concerned with the NO x control technology of choice for pulverized coal fired boilers, ?in-furnace NO x control,? which includes: staged low-NO x burners, reburning, selective non-catalytic reduction (SNCR) and hybrid approaches (e.g., reburning with SNCR). The program has two primary objectives: 1) To improve the performance of ?in-furnace? NO x control processes. 2) To devise new, or improve existing, approaches for maximum ?in-furnace? NO x control and minimum unburned carbon. The program involves: 1) fundamental studies at laboratory- and bench-scale to define NO reduction mechanisms in flames and reburning jets; 2) laboratory experiments ...

Energy Technology Data Exchange (ETDEWEB)

The core bypass flow in a prismatic very high temperature gas-cooled reactor (VHTR) is one of the important design considerations which impacts considerably on the integrity of reactor core internals including operating fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) will be affected by the bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to understand better the bypass flow phenomenon and establish the evaluation method in the reactor core using commercial CFD code FLUENT. Parametric ...

UK PubMed Central (United Kingdom)

Introduction:Single-stream hydro-jet dissection is increasingly used in various laparoscopic procedures, but its use requires special equipment. We describe a simple method for using...Full Text Available

International Nuclear Information System (INIS)

The studies of forced jet augmentation of natural convection heat transfer are introduced. It investigates experimentally mixed convection and heat transfer augmentation by forced jets in a large rectangular enclosure with a vertical cooling surface. The experiment is designed to measure the key parameters governing the heat transfer augmentation by a forced jet, and to investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio, on conditions simulating those of actual passive containment cooling systems and scales approaching those of actual containment buildings or compartments. The tests that cover a variety of injection modes will contribute to reveal the nature of mixing and stratification phenomena under accident conditions to a new generation of inherently safe reactors. With similarity ...

Energy Technology Data Exchange (ETDEWEB)

The authors present here several recent measurements involving associate production of photons and jets at the Tevatron. In particular, inclusive photon + met from D0, and photon + b-jets and photon + b-jet + leptons + MET from CDF are described in some detail. These measurements offer a good test of QCD predictions in rather complex final states.

International Nuclear Information System (INIS)

Plasma with a gas temperature below room temperature is not yet fully understood although it is expected to be an attractive tool for applications to material processing. In the present work, gas-temperature-dependent generation of a cryoplasma jet was studied. So far, we have generated a helium cryoplasma jet (296-5 K) under atmospheric pressure. At gas temperatures below 20 K, the helium excimer, He2, was observed clearly from by optical emission spectroscopy.

International Nuclear Information System (INIS)

In order to facilitate observations of low energy nuclear reactions, a new type recoil mass-separator together with a new gas-jet target system is being developed at the tandem accelerator facility in Kyushu University. The expected mass-resolving power of the separator is 220 for a solid angle of 10 msr and the practical thickness of the gas-jet target will exceed 0.1 atm#centre dot#cm for the light elements of H and He. (author).

Energy Technology Data Exchange (ETDEWEB)

Accurate lung tumor tracking in real time is a keystone to image-guided radiotherapy of lung cancers. Existing lung tumor tracking approaches can be roughly grouped into three categories: (1) deriving tumor position from external surrogates; (2) tracking implanted fiducial markers fluoroscopically or electromagnetically; (3) fluoroscopically tracking lung tumor without implanted fiducial markers. The first approach suffers from insufficient accuracy, while the second may not be widely accepted due to the risk of pneumothorax. Previous studies in fluoroscopic markerless tracking are mainly based on template matching methods, which may fail when the tumor boundary is unclear in fluoroscopic images. In this paper we propose a novel markerless tumor tracking algorithm, which employs the correlation between the tumor position and surrogate anatomic features in the image. The positions of the surrogate features are not directly ...

Science.gov (United States)

Apparent evolution of relativistic flows as traced by radio emission results from a combination of several factors related to propagation of relativistic blobs or shocks, velocity, density and pressure stratification of the underlying flow, plasma instability and (possibly also) phase and time travel effect. This combination can create an intricate and chaotic patterns of the observed morphological changes in radio emission, which complicates the analysis and interpretation of kinematic and physical properties of the jet plasma. Recent studies have indicated that slow and quasi-stationary patterns in jets are most likely formed by plasma instabilities while faster, superluminally moving patterns are related to highly relativistic plasma condensations produced by the nuclear flares. Some of the stationary patterns may also be related to recollimation shocks or locations where strong non-thermal continuum is produced in jets. ...

Energy Technology Data Exchange (ETDEWEB)

This experimental research investigates mixed convection and heat transfer augmentation by gaseous forced jets in a large enclosure, at conditions simulating those of passive containment cooling systems for Gen III+ passively safe reactors. The experiment is designed to measure the key parameters governing heat transfer augmentation by forced jets, and to investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio. The tests cover a variety of injection modes leading to flow configurations of interest for mixing and stratification phenomena in containments under accident conditions. Correlations for heat transfer augmentation by forced jets are developed and compared with experimental data. The characteristic recirculation speed inside the enclosure is introduced and analyzed. Steady stratified ...

CERN Document Server

We have developed a liquid jet injector system that can be used for hydrated sample delivery at X-ray Free Electron Laser (XFEL) sources and 3rd generation synchrotron sources. The injector is based on the Gas Dynamic Virtual Nozzle (GDVN), which generates a liquid jet with diameter ranging from 300 nm to 20 {\\mu}m without the clogging problems associated with conventional Rayleigh jets. An improved nozzle design is presented here. A differential pumping system protects the vacuum chamber and an in-vacuum microscope allows observation of the liquid jet for diagnostics while it is being exposed to the X-ray beam. A fiber optically coupled pump laser illuminating the jet is incorporated for pump-probe experiments. First results with this injector system have been obtained at the LCLS.

International Nuclear Information System (INIS)

The SIEN 2009 symposium organized by Romanian Nuclear Energy Association, AREN, in co-operation with Romanian Atomic Forum, ROMATOM, was primarily targeting the expert community involved in developing new nuclear power projects and implementing the National Nuclear Program. The symposium was also open as a discussion and information forum for scientists, engineers, technicians and students interested in scientific and technologic topics of Nuclear Power. It was structured in the following 6 sections: - Nuclear new builds and developments; - Operation, inspection and maintenance; - Increasing nuclear safety features; - Fuel cycle and decommissioning; - Public perception and confidence strengthening; - Environmental management. The symposium began with three plenary lectures dealing with: - Sustainable Nuclear Energy European Technology Platform; - Nuclear new-build; - Current issues of nuclear equipment standardization in Romania. A poster session of 5 presentations ...

Energy Technology Data Exchange (ETDEWEB)

In this work the authors study the stabilization point of a lifted, reacting jet of nitrogen diluted methane in co-flowing air. The jet flow is acoustically forced so as to organize the large scale vortical structures. The validation of the numerical results is possible through a concurrent experimental investigation of a similar planar jet. The use of an acoustically forced planar jet allows for significant savings by the restriction of the computation to two dimensions; the model is otherwise applicable in three dimensions. The authors based their study on the following parameters, which are derived from the experimental setup: a jet width of 1.16 cm, a mean jet velocity of 0.8 m/s, and a coflow velocity of 0.1 m/s. The acoustical forcing is studied at frequencies of 7.5 MHz and 90 MHz, which have been established experimentally as being characteristic of two ...

International Nuclear Information System (INIS)

One way to intensify heat and mass transfer processes in column-type equipment is through use of contact devices with directional gas phase injection into a liquid. Making the perforations at an angle to the tray plane permits a rise in the permissible gas velocity in the column, since inertial force adds to gravity during separation. Different arrangements of the jet-forming elements relative to one another and to partitions and baffle-type contacts installed on the trays can improve phase contact conditions and intensify heat and mass transfer. Design of jet-type trays for a specific purpose requires that the influence of jet-forming, element design parameters on at least the fluid dynamic situation on the tray be known. In this work, the authors evaluate the influence of tab bend-up angle on jet tray working characteristics. These investigations demonstrate that the jet ...

Energy Technology Data Exchange (ETDEWEB)

Fabrication processes for FFTF fuel pins are described.

Energy Technology Data Exchange (ETDEWEB)

Although the standard model of particle physics agrees perfectly with experimental data, it is unlikely the final theory describing particles and their interactions. New phenomena has been searched in the jets and missing transverse energy topology. Such phenomena may be due to the pair production of leptoquarks decaying into a quark and a neutrino or the pair production of stops decaying into a charm and a neutralino which is assumed to be the lightest supersymmetric particle. These searches have been performed with the Ddiamter detector at hadronic collider TeVatron with a center of mass energy of 1.96 TeV. This kind of searches needs a good understanding of the jet energy calibration. The determination of the relative jet energy scale has allowed us to reduce the systematic uncertainties on the jet energy measurement when comparing the data and the simulation. Moreover a new method has been developed ...

CERN Document Server

We report results of the 2006 April multi-wavelengths campaign of SS 433, focusing on X-ray data observed with Suzaku at two orbital phases (in- and out-of- eclipse) and simultaneous optical spectroscopic observations. By analyzing the Fe25 K_alpha lines originating from the jets, we detect rapid variability of the Doppler shifts, dz/dt ~ 0.019/0.33 day^-1, which is larger than those expected from the precession and/or nodding motion. This phenomenon probably corresponding to "jitter" motions observed for the first time in X-rays, for which significant variability both in the jet angle and intrinsic speed is required. From the time lag of optical Doppler curves from those of X-rays, we estimate the distance of the optical jets from the base to be ~(3-4) \\times 10^14 cm. Based on the radiatively cooling jet model, we determine the innermost temperature of the jets to be T_0 = 13 +/- ...

CERN Document Server

We present the results of a study on the 1.4 GHz kpc-scale radio emission in the complete flux density limited MOJAVE sample, comprising 135 radio-loud AGNs. While extended emission is detected in the majority of the sources, about 7% of the sources exhibit only radio core emission. Many BL Lacs exhibit extended radio power and kpc-scale morphology typical of powerful FRII jets, while a substantial number of quasars possess radio powers intermediate between FRIs and FRIIs. This poses challenges to the simple radio-loud unified scheme, which links BL Lacs to FRIs and quasars to FRIIs. We find a significant correlation between extended radio emission and pc-scale jet speeds: the more radio powerful sources possess faster jets. This indicates that the 1.4 GHz (or low frequency) radio emission is indeed related to jet kinetic power. Various properties such as extended radio power and apparent pc-scale ...

CERN Document Server

we report an ultrafast synchrotron x-ray phase contrast imaging study of the primary breakup mechanism of a coaxial air-assisted water jet. We demonstrate that there exist great similarities in the phenomenology of primary breakup with that of the secondary breakup. Especially, a membrane-mediated breakup mechanism dominates the breakup process for a wide range of air speeds. This finding reveals the intrinsic connections of these two breakup regimes and has deep implications on the unified theoretical approach in treating the breakup mechanism of high speed liquid jet.

Energy Technology Data Exchange (ETDEWEB)

The performance of a high temperature ion source coupled to a helium gas-jet transport system for an efficient mass separation of neutron-rich alkaline earth and lanthanide isotopes is reported and the results of overall efficiency measurements using different cluster materials in the gas-jet are given. A fast, microprocessor controlled tape transport system for ..gamma..-spectroscopic studies on short-lived isotopes is described. Some results on the decay of 3.8sub(-s) /sup 152/Pr are presented.

Science.gov (United States)

Unsteady impinging jets are systematically controlled with respect to their time dependence in order to investigate the influence of unsteadiness on the heat transfer performance. This is achieved by a special mass flow control device, which allows almost arbitrary shapes of unsteadiness to be imposed onto the impinging jet. Three different standard signals (sinusoidal, triangular, rectangular) and two specially designed signals are applied and their influence on heat transfer is determined in terms of an enhancement factor. Heat transfer augmentation up to 30% was found and could be physically explained with the help of PIV and hot-wire measurements of the flow field.

Science.gov (United States)

Engine flow simulation was provided by four separately mounted air ejectors connected to a high-pressure air supply. The engine nacelle center lines were ...

International Nuclear Information System (INIS)

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10 ?s with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 1019 cm-3, compared with theoretical simulations from the nozzle parameters.

Science.gov (United States)

... ai jets used for chip removal. Control is normally effectd through the use of miscellaneous function M Codes on the postprocessor NC output. ...

International Nuclear Information System (INIS)

Smoothing of laser beam non-uniformities using gas jets has been studied. The experiment has been performed with the PALS (Prague Asterix Laser System) laser working at 0.44 ?m with an intensity of about 1015 W/cm2. The laser beam has been split in two by a prism thus creating an artificial large-scale non-uniformity (? 90 ?m). We recorded time resolved and static images of laser-gas jet interaction with and without an Al target. Multi 1-dimensional and 2-dimensional simulations show that such interaction acts redistributing the over-intensities over larger surface. This effect has to be attributed to ionization processes with consequent laser beam refraction. Results show that Argon gas jet produces a strong refraction of the laser beam thus strongly reducing the initial two spots separation. (authors)

Science.gov (United States)

Jun 30, 2003 ... He graduated from training with top honors and served as a parachute rigger and paratrooper for the 82nd airborne division at Fort Bragg, ...

International Nuclear Information System (INIS)

English 1992 p. 146 China Yuan Shuanggui Xu Shuwei Zhang Xueqian Atomic

Science.gov (United States)

A Self-Powered Underwater Robot for Ocean Exploration and Beyond ... first unmanned underwater vehicle (UUV) that is completely powered by renewable energy . ...

Energy Technology Data Exchange (ETDEWEB)

For the performance analysis of Canadian deuterium uranium (CANDU) reactor shutdown system number 2 (SDS2), a computational fluid dynamics model of poison jet flow has been developed to estimate the flow field and poison concentration formed inside the CANDU reactor calandria. As the ratio of calandria shell radius over injection nozzle hole diameter is so large (1055), it is impractical to develop a full-size model encompassing the whole calandria shell. In order to reduce the model to a manageable size, a quarter of one-pitch length segment of the shell was modeled using symmetric nature of the jet; and the injected jet was treated as a source term to avoid the modeling difficulty caused by the big difference of the hole sizes. For the analysis of an actual CANDU-6 SDS2 poison injection, the grid structure was determined based on the results of two-dimensional real- and source-jet simulations. The ...

Science.gov (United States)

May 1, 2011 ... Abstract: Diatek Corporation, San Diego, CA and the Jet Propulsion Lab developed the Diatek Model 7000 aural thermometer which weighs ...

Science.gov (United States)

The jet in cross flow (JICF) is a basic flowfield which is relevant to a wide variety of applications which are described to provide context for JICF investigations. Material consistent with the scope of topics presented at the 72nd AGARD Fluid Dynamics Panel Meeting and Symposium on Computational and Experimental Assessment of Jets in Cross Flow on 19-22 April 1993 in Winchester, U.K. is summarized. The JICF research was divided into three time periods: (1) early research - up to 1970, (2) research during the 1970's, and (3) research since 1980. The following areas of experimental activity are discussed; the definition of an effective correlation parameter; the jet flowfield including the jet trajectories, cross-section shape, and jet induced pressures; the effects of jet deflection angle, nozzle shape, pressure ratio, velocity decay, and temperature; and the ...

Science.gov (United States)

Barlow, Nadine Northern Arizona University, Flagstaff, AZ. 10. Barker, Don NASA Johnson Space Center, TX. 11. Beaty, David NASA Jet Propulsion Laboratory, ...

Science.gov (United States)

Post-drive imaging included 360-degree view by the navigation camera and .... Sol 938: Opportunity completed another assessment of the clarity of the sky. ...

Energy Technology Data Exchange (ETDEWEB)

We have recently introduced several important improvements in the measurement of distillation curves for complex fluids. The modifications include a composition-explicit data channel for each distillate fraction (for both qualitative and quantitative analysis) and corrosivity assessment of each distillate fraction. The composition-explicit information is achieved with a new sampling approach that allows precise qualitative as well as quantitative analyses of each fraction, on the fly. We have applied the new method to a variety of fluids, including simple n-alkanes, rocket propellant, gasoline, jet fuels, and a hydrocarbon fluid made corrosive with dissolved hydrogen sulfide. In the current contribution, we present the application of the advanced distillation curve method to two samples of crude oil. A primary motivation behind the work is to precisely measure the distillation curves of these oils using our advanced distillation apparatus; ...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents the work achieved to instrument the ATLAS software framework, ATHENA, with a library of tools and utensils for the physics analysis as well as the extraction of the jet energy scale using physics events (in-situ calibration). The software part presents the various components of the ATHENA framework which handles the simulated and reconstructed data flow as well as the different stages of this process, before and during the data taking. The building of a library of tools easing the reconstruction of physics objects, their association with Monte-Carlo particles and their API is then explained. The need for common language and collaboration-wide utensils is emphasised as it allows to share the workload of validating these tools and to get reproducible physics results. The analysis part deals with the implementation of a light jet energy scale calibration algorithm within the C++ framework. This calibration algorithm makes use ...

DEFF Research Database (Denmark)

Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields and dynamics. Data were analysed using Proper Orthogonal Decomposition (POD). An important periodic event is an elongation of the jet core cross section that results in a downstream displacement of the jet towards the chamber wall.

Energy Technology Data Exchange (ETDEWEB)

The apex dimensions and length are calculated as a function of current for the ion-emitting jet in liquid-metal ion sources (LMIS). The results agree well with observations. Since the final expressions are analytical, they give more insight into the fundamental mechanisms involved than do numerical calculations. Some implications of the model are discussed concerning focused ion beam (FIB) systems employing LMIS. (author).

Energy Technology Data Exchange (ETDEWEB)

A fuel composition comprising a liquid hydrocarbon fuel and a detergent amount of the product of reaction between a polyamine and a stearic acid is described.

Energy Technology Data Exchange (ETDEWEB)

Plasma nitriding of a Ti substrate is carried out under a low ambient pressure below 3kPa, and a plasma torch is prepared on a trial basis which is provided with a supersonic expansion nozzle considered to expand plasma jet optimally and to be effective for suppressing the occurrence of shock wave. The system used for the study is provided with a specimen holder having the function of adjusting the distance between the nozzle outlet and the substrate inside the vacuum chamber which is provided with a plasma torch in the flange member. The plasma torch is so structured that a supersonic expansion nozzle can be installed at the tip of the plasma torch. In this process wherein plasma jet is employed, hard nitrided layer can be formed by plasma irradiation for a short time even under such low pressure as less than 3kPa by setting adequate experimental conditions. It is made clear that the use of a supersonic nozzle corresponding to the internal ...

International Nuclear Information System (INIS)

The authors discuss a two-phase two-component experimental system developed to study enhancement of heat transfer from a vertical chip size heater to surrounding liquid (Freon 113 or Ethanol) due to air jet impingement. Heat transfer coefficient was measured as function of jet velocity, heat flux and the distance between exit of jet tube and heated surface. The injector was placed very close to the hot surface. It was found that the heat transfer was notably enhanced with foreign gas impingement, especially in the cases of small temperature differences between wall and coolant. In fact for higher jet velocities the heat transfer coefficients tended to infinite while the temperature differences between wall and coolant were zero. The heat transfer coefficients decreased with the increasing of heat flux. High-speed camera was used to study the behaviour of the gas bubbles which play very important role in ...

Wastenet

...Basic Information | Fuel Cells & Vehicles | US EPA This web page provides basic information on EPA's Fuel Cells & Vehicles web site ...including the chemical composition of fuel cell technology, how it works, descriptions of the various types of fuel cells , their availability and ... background,electrochemical,hydrogen,fuel cell,fuel cell vehicle,fuel reformer,performace,improved fuel economy,increased engine efficiency,lower emissions,zero emissions,availablity,fuel cell types,diagram,Proton ...Exchange Membrane,PEM Basic Information | Fuel Cells & Vehicles | US EPA background,electrochemical,hydrogen,fuel cell,fuel cell vehicle,fuel reformer,performace,improved fuel economy,...

International Science & Technology Center (ISTC)

Plasma Technologies of Solid Fuels Processing for Power Engineering and Metallurgy

Energy Technology Data Exchange (ETDEWEB)

This patent describes a gas-diesel dual fuel engine apparatus having a diesel engine, a diesel fuel supply system including a diesel fuel injection pump, a gaseous fuel supply system including gaseous fuel regulating valve, and a governing and controlling device for governing the speed of the engine and controlling the switchover of the operation of the engine between a diesel fuel mode and a gaseous fuel mode.

International Nuclear Information System (INIS)

... electric utilities electrochemistry energy storage fuel cells organizational models

International Nuclear Information System (INIS)

... FUEL CYCLE AND FUEL MATERIALS MATERIALS SCIENCE chromium-nickel

International Nuclear Information System (INIS)

We report on the discovery of kinematic shock signatures associated with a localized radio jet interaction in the merging Seyfert galaxy NGC 5929. We explore the velocity-dependent ionization structure of the gas and find that low-ionization gas at the interaction site is significantly more disturbed than high-ionization gas, which we attribute to a local enhancement of shock ionization due to the influence of the jet. The characteristic width of the broad low-ionization emission is consistent with shock velocities predicted from the ionization conditions of the gas. We interpret the relative prominence of shocks to the high density of gas in the nuclear environment of the galaxy and place some constraints of their importance as feedback mechanisms in Seyferts.

CERN Document Server

We present evidence in favour of a link between the luminosity radiatively dissipated in the central engine of radio-loud Active Galactic Nuclei and the kinetic power in their jets. This piece of evidence is based on the relation we find between the luminosity in broad emission lines and the kinetic power in pc-scale radio jets, for a sample of radio-loud quasars for which suitable data are available in the literature. We find that the ionizing luminosity and the kinetic one are of the same order of magnitude, suggesting that the processes responsible for them are somehow related. A strong magnetic field in equipartition with the radiation field could be responsible for regulating both processes. BL Lac objects seem to follow a similar behaviour, but with comparatively fainter broad line emission.

British Library Electronic Table of Contents (United Kingdom)

Displacement Ventilation (DV) offers a great opportunity to improve indoor air quality while reducing the energy consumption compared to mixing ventilation. A frequent problem with displacement ventilation is however the draft discomfort caused by the cold air movement at foot level and excessive temperature difference between head and ankle. Despite numerous past studies, there is still a lack of detailed data regarding the velocity and temperature distribution inside DV jets. In this experimental study, measurements of the air velocity and temperature are performed in the DV jet produced by a flat wall-mounted DV diffuser, using a fine mesh focused on the 0.00-0.20 m height range. Two supply conditions are studied. Three planes of measurements are covered: the vertical longitudinal plane...

Energy Technology Data Exchange (ETDEWEB)

A number of epidemiological studies indicate an association between depression and proximity to high voltage transmission lines. These studies have been criticized, however, for using surrogate measures of electromagnetic fields (EMFs) and unstandardized measures of depression. In an effort to overcome these limitations, the Center for Epidemiological Studies Depression (CES-D) scale was administered to 152 women living either adjacent to a transmission line or one block away. Results indicate that homes adjacent to the transmission lines have an average EMF level of 4.86 milligauss at their front door and those one block away have an average of 0.68 milligauss. There was no significant difference in CES-D scores between the groups, controlling for demographic variables. There appeared to be an increase in other health effects, including cancer and miscarriages, but these findings were preliminary and need further investigation.

International Nuclear Information System (INIS)

The current Risk-informed Regulation (RIR) framework employs both a Level 1 Core Damage Frequency (CDF) and a Level 2 Large Early Release Frequency (LERF) as two surrogate measures for the plant risk. For their use in making regulatory decisions for the plant risk, it has been required to maintain an appropriate level of quality for the plant risk models. The first step for this purpose is to evaluate the quality of the PSA model in a qualitative or quantitative manner. Recently, a similar type of quality evaluation has been made for the KSNP Level 1 PSA model based on an ASME PRA Standard for the RIR application, but not for the corresponding LERF model. The main objective of this paper is to provide the ASME PRA Standard-based evaluation result for the existing KSNP Level 2 LERF model and the insights obtained from the evaluation process

British Library Electronic Table of Contents (United Kingdom)

The purpose of this study was to investigate whether the expression of specific genes in peripheral blood can be used as surrogate marker(s) to detect and distinguish target organ toxicity induced by chemicals in rats. Rats were intraperitoneally administered a single, acute dose of a well-established hepatotoxic (acetaminophen) or a neurotoxic (methyl parathion) chemical. Administration of acetaminophen (AP) in the rats resulted in hepatotoxicity as evidenced from elevated blood transaminase activities. Similarly, administration of methyl parathion (MP) resulted in neurotoxicity in the rats as evidenced from the inhibition of acetyl cholinesterase activity in their blood. Administration of either chemical also resulted in mild hematotoxicity in the rats. Microarray analysis of the global ...

British Library Electronic Table of Contents (United Kingdom)

Background: Cardio-respiratory interactions are weak at the earliest stages of human development, suggesting that assessment of their presence and integrity may be an important indicator of development in infants. Despite the valuable research devoted to infant development, there is still a need for specifically targeted standards and methods to assess cardiopulmonary functions in the early stages of life. We present a new methodological framework for the analysis of cardiovascular variables in preterm infants. Our approach is based on a set of mathematical tools that have been successful in quantifying important cardiovascular control mechanisms in adult humans, here specifically adapted to reflect the physiology of the developing cardiovascular system.Methods: We applied our methodology ...

Science.gov (United States)

Page 1. Page 2. Page 3. Page 4. Page 5. Page 6. Page 7. Page 8. Page 9. Page 10. Page 11. Page 12. Page 13. Page 14. Page 15. Page 16. Page ...

Science.gov (United States)

The astronomical number of letters handled by the Post Office makes automatic sorting technology essential. Key roles are played by the postcode system and an ink-jet printer that has been developed to use phosphorescent inks.

CERN Document Server

The bright gamma-ray burst GRB050525a has been detected with the Swift observatory, providing unique multiwavelength coverage from the very earliest phases of the burst. The X-ray and optical/UV afterglow decay light curves both exhibit a steeper slope ~0.15 days after the burst, indicative of a jet break. The timing of the jet break combined with the total gamma-ray energy of the burst constrains the opening angle of the jet to be 2.5 degrees. We derive an empirical `time-lag' redshift from the BAT data of z_hat = 0.69 +/- 0.02, in good agreement with the spectroscopic redshift of 0.61. Prior to the jet break, the X-ray data can be modelled by a simple power law with index alpha = -1.2. However after 300s the X-ray flux brightens by about 30% compared to the power-law fit. The optical/UV data have a more complex decay, with evidence of a rapidly falling reverse shock component that dominates in the ...

Science.gov (United States)

Telecommunication Union IVDT integrated voice data terminal IXC interexchange carrier JANAP Joint Army-Navy-Air Force Publication(s) JCS Joint Chiefs of Staff JPL Jet Propulsion...

UK PubMed Central (United Kingdom)

Objective:This the first of two articles reviewing the scientific literature on the evaluation and treatment of circadian rhythm sleep disorders (CRSDs), employing the methodology...Full Text Available

Science.gov (United States)

Jan 22, 2011 ... dc.subject.other, Cost cost estimating budgets budget estimating ... dc.title, Estimating the Cost of Doing a Cost Estimate, en_US ...

Energy Technology Data Exchange (ETDEWEB)

An impinging jet is a widely used technique for realizing high heat-transfer rates between a fluid and a surface. However, the area of enhanced heat transfer is limited to the neighborhood of the stagnation point. In this study, heat transfer is augmented remote from the stagnation point in an impinging plane jet system by a rod array located near the wall. Each square rod in the array was positioned normal to the flow direction and parallel to the flat plate surface. The distance between the nozzle and the flat plate (H) and the spacing between the rods and the flat plate surface (C) were changed to find the optimum values. The largest heat-transfer augmentation was obtained for C = 1 mm, H/B = 10, where the jet nozzle width is B. In this case, the heat-transfer coefficient averaged over an area 2B from the stagnation point is about 1.6 times greater compared to that without a rod array.

CERN Document Server

The evolution of FRI jets has been long studied in the framework of the FRI-FRII dichotomy. In this paper, we test the present theoretical and observational models via a relativistic numerical simulation of the jets in the radio galaxy 3C 31. We use the parameters derived from the modelling presented by \\cite{lb02a,lb02b} as input parameters for the simulation of the evolution of the source, thus assuming that they have not varied over the lifetime of the source. We simulate about 10 % of the total lifetime of the jets in 3C 31. Realistic density and pressure gradients for the atmosphere are used. The simulation includes an equation of state for a two-component relativistic gas that allows a separate treatment of leptonic and baryonic matter. We compare our results with the modelling of the observational data of the source. Our results show that the bow shock evolves self-similarly at a quasi-constant speed, with slight ...

Energy Technology Data Exchange (ETDEWEB)

This report beings with a historical overview on the origin and early beginnings of Radiant Energy Power Source for Jet Aircraft. The report reviews the work done in Phase I (Grant DE-FG01-82CE-15144) and then gives a discussion of Phase II (Grant DE-FG01-86CE-15301). Included is a reasonably detailed discussion of photovoltaic cells and the research and development needed in this area. The report closes with a historical perspective and summary related to situations historically encountered on projects of this nature. 15 refs.

Energy Technology Data Exchange (ETDEWEB)

The uranium target of a gas jet transport system for fission products has been modified by the addition of an aluminum cover foil. The new modification allows fission fragments of low mass to enter a continuous chemistry system while heavier fragments are stopped in the aluminum. The elimination of the heavier homologues allows development of simpler and faster chemical separation procedures. In addition, since the lighter fragments are slowed down by the cover foil a smaller target chamber can be used. This leads to a reduction in system holdup time.

CERN Document Server

We present results for a complete set of polarization observables for jet production in lepton proton collision, where the final state lepton is not observed. The calculations are carried out in collinear factorization at the level of Born diagrams. For all the observables we also provide numerical estimates for typical kinematics of a potential future Electron Ion Collider. On the basis of this numerical study, the prospects for the transverse single target spin asymmetry are particularly promising. This observable is given by a certain quark-gluon correlation function, which has a direct relation to the transverse momentum dependent Sivers parton distribution.

British Library Electronic Table of Contents (United Kingdom)

Abstract First results showing the viability of combining laser chemical processing (LCP) and aerosol jet printing (AJP) technologies to produce a high-efficiency front side for silicon solar cells are presented. LCP simultaneously opens the anti-reflection coating (ARC) and highly dopes the underlying silicon to create a selective emitter, while AJP is the first in a two-step fine-line contact formation procedure. The electrical properties as well as the morphology of the resulting structures are presented. Performance similar to that achieved with evaporated TiPdAg metallization is demonstrated. Copyright 2010 John Wiley & Sons, Ltd.

Energy Technology Data Exchange (ETDEWEB)

Washboard (WB) modes (Smeulders P et al 1999 Plasma Phys. Control. Fusion 41 1303) are a very common edge instability regularly observed in the H-mode regime in JET. They are detected as (normally several) bands of continuously fluctuating magnetic activity rotating in the direction of the electron diamagnetic drift with typical frequencies in the range of 10-90 kHz. The time evolution of the WB mode frequency is found to follow qualitatively the evolution of the electron temperature measured near the pedestal top, probably due to the strong diamagnetic drift associated with the large pedestal gradients. Evidence for their involvement in the pedestal and ELM dynamics will be presented. Increasing WB mode amplitude is correlated with an increase in the time between consecutive type-I ELMs. In situations in which a sudden increase (decrease) of WB mode activity is observed, the build-up of the pedestal temperature (and, linked to this, also of the pedestal pressure) ...

International Nuclear Information System (INIS)

An original dc double anode plasma torch which provides a long-time and highly stable atmospheric plasma jet has been devised for the purpose of hazardous waste treatment. The arc fluctuations and dynamic behaviour of the argon and argon-nitrogen plasma jets under different operating conditions have been investigated by means of classical tools, such as the statistic method, fast Fourier transform (FFT) and correlation analysis. In our experiments, the takeover mode is identified as the fluctuation characteristic of the argon plasma jet while the restrike mode is typical in the argon-nitrogen plasma dynamic behaviour. In the case of pure argon, the FFT and correlation calculation results of electrical signals exhibit the only characteristic frequency of 150 Hz, which originates from the torch power and is independent of any change in the operating conditions. It indicates that the nature of fluctuations in an argon plasma ...

Energy Technology Data Exchange (ETDEWEB)

The effects of changes in the cetane number of liquid pilot fuels on the ignition delay period in dual fuel engines were investigated experimentally. Various pilot fuel quantities were employed with methane, propane and low heating value gaseous fuel mixtures over a wide range of engine load.the ignition delay variation with increased gaseous fuel admission showed a strong dependence on both the quantity and the quality of the pilot fuel used. It was found that the use of high cetane number pilot liquid fuels permitted smaller pilot quantities to be used satisfactorily. Engine operation on propane and low heating value gaseous fuels improved in comparison with dual fuel engine operation employing common diesel fuels.

Wastenet

... Fuel Cell Technologies Equipment on Environmental Expert Find and compare a variety of fuel cell technologies equipment on the world's largest environmental industry portal. View ...

Science.gov (United States)

Proton exchange membrane (PEM) fuel cells are energy sources that have the ... for H2 /02 PEM fuel cells because their catalysts have properties suitable for 0 ...

Energy Technology Data Exchange (ETDEWEB)

This bulletin describes case studies of trucks operating on ethanol fuel. Cost, maintenance and repair, as well as fuel economy are discussed.

International Nuclear Information System (INIS)

We have successfully incorporated high surface area particles of titanate ion exchange materials (monosodium titanate and crystalline silicotitanate) with acceptable particle size distribution into porous and inert support membrane fibrils consisting of polytetrafluoroethylene (Teflon(reg_sign)), polyethylene and cellulose materials. The resulting membrane sheets, under laboratory conditions, were used to evaluate the removal of surrogate radioactive materials for cesium-137 and strontium-90 from high caustic nuclear waste simulants. These membrane supports met the nominal requirement for nonchemical interaction with the embedded ion exchange materials and were porous enough to allow sufficient liquid flow. Some of this 47-mm size stamped out prototype titanium impregnated ion exchange membrane discs was found to remove more than 96% of dissolved cesium-133 and strontium-88 from a caustic nuclear waste salt simulants. Since in traditional ion exchange based column ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The modification of a Ford 7600 turbocharged diesel engine to a dual fuel engine using methane as the supplementary fuel has been carried out. The paper describes the preliminary work of dual fuel control. Two systems are examined and their behaviour is presented.

International Nuclear Information System (INIS)

Due to depletion of fossil fuel, bio-fuels have generated a significant interest as an alternative fuel for the future. The use of bio-fuels to fuel gas turbine seems a viable solution for the problems of decreasing fossil-fuel reserves and environmental concerns. Bio-fuels are alternative fuels, made from renewable sources and having environmental benefit. In recent years, the desire for energy independence, foreseen depletion of nonrenewable fuel resources, fluctuating petroleum fuel costs, the necessity of stimulating agriculture based economy, and the reality of climate change have created an interest in the development of bio-fuels. The application of bio-fuels in automobiles and heating applications is increasing day by day. ...

International Nuclear Information System (INIS)

The LWR fuel performance analysis computer code, FRAPCON-1, are evaluated to investigate the performance of CANDU fuel elements loaded in Wolsung-1 reactor. The FRAPCON-1 models of neutron flux depression in fuel and of fuel-to-cladding heat transfer are modified, and the validity of fission gas release model for CANDU fuel is evaluated. And the heavy water properties are provided in calculating the heat transfer coefficient between cladding and coolant. By using the modified code, FRAPCON-1-CSK, the sensitivity studies are carried out for Wolsung-1 fuel element design parameters. The performance analysis is also performed for Wolsung-1 fuel elements. The calculated results are discussed in terms of LWR fuel design criteria because of unavailability of CANDU fuel design criteria. (Author).

Energy Technology Data Exchange (ETDEWEB)

A compression ignition engine was operated on dual fuel principle inducting two commercial fuels and four pure hydrocarbon fuels in turn through intake manifold along with air and injecting diesel fuel to initiate the combustion in the conventional manner. The engine was operated at different loads and at each load the quantity of inducted fuel was increased gradually till knocking set in. The engine performance and exhaust pollutant emissions were recorded at different operating conditions. It was observed that the extent of induction and the effect on the performance depend on the properties of the inducted fuel such as volatility, self ignition temperature and oxidation characteristics. The energy release during the cycle was also observed to shift depending on the properties of inducted fuel. With the dual fuel ...

International Science & Technology Center (ISTC)

Safe Transference of Spent Fuel Assemblies from Near-Reactor Storage Pools to Long-term "Dry" Storage

International Nuclear Information System (INIS)

... Natural convection cooling of the channel type reactor performed with the fuel

International Science & Technology Center (ISTC)

Behavior of Nuclear Reactor Fuel Assembly Materials during Their Long-Term Dry Storage

Energy Technology Data Exchange (ETDEWEB)

This is a continuation of research that started in July 2007 at the Deep River Science Academy. The research was related to the effects of endplate thickness and misalignment of fuel bundles in the fuel channel on pressure losses of reactor coolant. Based on this research, a new approach to refueling of the CANDU reactor has been developed. It greatly simplifies fuel handling equipment and increases its reliability. It also reduces required staffing, as well as operating and maintenance costs associated with fuel handling. (author)

International Nuclear Information System (INIS)

The paper discusses recent results on the development of localized arc filament plasma actuators and their use in controlling high-speed and high Reynolds number jet flows. Multiple plasma actuators (up to 8) are controlled using a custom-built 8-channel high-voltage pulsed plasma generator. The plasma generator independently controls pulse repetition rate (0-200 kHz), duty cycle and phase for each individual actuator. Current and voltage measurements demonstrated the power consumption of each actuator to be quite low (20 W at 20% duty cycle). Emission spectroscopy temperature measurements in the pulsed arc filament showed rapid temperature increase over the first 10-20 ?s of arc operation, from below 1000 deg. C to up to about 2000 deg. C. At longer discharge pulse durations, 20-100 ?s, the plasma temperature levels off at approximately 2000 deg. C. Modelling calculations using an unsteady, quasi-one-dimensional arc filament model showed that rapid localized ...

Energy Technology Data Exchange (ETDEWEB)

The invention concerns a device for the energy-saving heating of fuel in the supply pipe to an internal combustion engine to regain energy from the fuel itself, particularly but not exclusively for a Diesel engine. A part of the quantity of heat added to the fuel between the tank and the injection nozzles is given up by excess fuel not to the tank, but to the fuel lifted upstream of the injection pump. The device is characterised by the fact that it has a heat exchanger, which absorbs heat from the fuel at the level of the injection pump or upstream of it, and takes this to the fuel above the injection pump. The heat exchanger is preferably mounted upstream of a filter and close to it. A bridging pipe, which may be integrated in the heat exchanger, permits the heat exchanger to be short-circuited depending on the fuel ...

CERN Document Server

We introduce a methodology for analysis of multiwavelength data from X-ray selected BL Lac (XBL) objects detected in the TeV regime. By assuming that the radio--through--X-ray flux from XBLs is nonthermal synchrotron radiation emitted by isotropically-distributed electrons in the randomly oriented magnetic field of a relativistic blazar jet, we obtain the electron spectrum. This spectrum is then used to deduce the synchrotron self-Compton (SSC) spectrum as a function of the Doppler factor, magnetic field, and variability timescale. The variability timescale is used to infer the comoving blob radius from light travel-time arguments, leaving only two parameters. With this approach, we accurately simulate the synchrotron and SSC spectrum of flaring XBLs in the Thomson through Klein-Nishina regimes. Photoabsorption by interactions with internal jet radiation and the intergalactic background light (IBL) is included. Doppler factors, magnetic fields, ...

CERN Document Server

We consider the physics and collider phenomenology of quirks that transform nontrivially under QCD color, SU(2)_W as well as an SU(N)_{ic} infracolor group. Our main motivation is to show that the recent Wjj excess observed by CDF naturally arises in quirky models. The basic pattern is that several different quirky states can be produced, some of which beta-decay during or after spin-down, leaving the lightest electrically neutral quirks to hadronize into a meson that subsequently decays into gluon jets. We analyze LEP II, Tevatron, UA2, and electroweak precision constraints, identifying the simplest viable models: scalar quirks ("squirks") transforming as color triplets, SU(2)_W triplets and singlets, all with vanishing hypercharge. We calculate production cross sections, weak decay, spin-down, meson decay rates, and estimate efficiencies. The novel features of our quirky model includes: quirkonium decay proceeds into a pair of gluon jets, ...

Energy Technology Data Exchange (ETDEWEB)

We intend to solve equations governing turbulent plane-vertical isotherm and non isotherm jets by taking into account inflow conditions at the exit of the nozzle. The analysis is focused on the influence of these conditions on this type of flow. Two cases are considered (uniform and parabolic velocity and temperature profiles). A finite difference scheme is developed to solve the governing equations. This numeric model allows us to show that the region of fully developed regime begins much nearer the nozzle for the turbulent case than for the laminar flow case. Indeed, the turbulence increases the mixing between the incoming gas from the nozzle and the ambient fluid, and consequently the size of the potential core zone decreases. The results are compared to other works introducing mathematical variables based on the energy conservation for the case of the mixed convection and the momentum conservation for the forced convection, which allows the validation of our ...

Science.gov (United States)

The objective of the program is to develop a domestic cooktop with low-NOx emissions and high efficiency. During the first two phases of the program, three design concepts were developed, and two versions of developmental prototypes using the IR-Jet approach were fabricated and tested. The third phase was initiated to address the design issues of burner turndown and modulation and to conduct the field test of a prototype with one IR-Jet and three conventional burners. Two prototypes containing one IR-Jet and three conventional burners and utilizing blower speed control for air/gas modulation were fabricated. One unit employed a brushless dc motor and the other a 2-pole ac motor. The ac motor prototype was field tested. Field testing showed the need for a mechanical air/gas valve for modulation and for a 1500 Btu/hr simmer setting. A 4-inch-diameter stepped-tile configuration provided input rates from 1500 to 8000 Btu/hr. A ...

CERN Document Server

While feedback is important in theoretical models, we do not really know if it works in reality. Feedback from jets appears to be sufficient to keep the cooling flows in clusters from cooling too much and it may be sufficient to regulate black hole growth in dominant cluster galaxies. Only about 10% of all quasars, however, have powerful radio jets, so jet-related feedback cannot be generic. The outflows could potentially be a more common form of AGN feedback, but measuring mass and energy outflow rates is a challenging task, the main unknown being the location and geometry of the absorbing medium. Using a novel technique, we made first such measurement in NGC 4051 using XMM data and found the mass and energy outflow rates to be 4 to 5 orders of magnitude below those required for efficient feedback. To test whether the outflow velocity in NGC 4051 is unusually low, we compared the ratio of outflow velocity to escape ...

CERN Document Server

We report on the results of a simultaneous monitoring campaign employing eight Chandra X-ray (0.5-10 keV) and six VLA/EVLA (8.4 GHz) radio observations of NGC 4051 over seven months. Evidence for compact jets is observed in the 8.4 GHz radio band; This builds on mounting evidence that jet production may be prevalent even in radio-quiet Seyferts. Assuming comparatively negligible local diffuse emission in the nucleus, the results also demonstrate an inverse correlation of L_radio proportional to L_X-ray ^(-0.72+/-0.04) . Current research linking the mass of supermassive black holes and stellar-mass black holes in the "low/hard" state to X-ray luminosities and radio luminosities suggest a "fundamental plane of accretion onto black holes" that has a positive correlation of L_radio proportional to L_X-ray^(0.67+/-0.12) . Our simultaneous results differ from this relation by more than 11 sigma, indicating that a separate mode of accretion and ...

International Nuclear Information System (INIS)

Since January, 1981, the project of development of nuclear fuel fabrication technology for Wolsung reactor (CANDU type) was undertaken by KAERI(Korea Advanced Energy Research Institute) and successfully fulfilled with loading 24 fuel bundles made by KAERI in Wolsung reactor in September, 1984. On the basis of this accumulated technology and experience, mass production plan to supply all the nuclear fuels for Wolsung reactor is under way. In this presentation, the Korean experience in the development of the nuclear fuel fabrication technology, safety and performance evaluation of KAERI fuel and the results of irradiation of KAERI fuels in Wolsung reactor will be described.

Science.gov (United States)

The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for component ...

International Nuclear Information System (INIS)

The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for component failures ...

Energy Technology Data Exchange (ETDEWEB)

The microstructural development and grain-coarsening behavior of WC-Co alloys, with and without a VC additive, were investigated. The primary goal was to determine the mechanism through which VC acts as a grain-growth inhibitor. The study involved long-time sintering experiments (1 to 100 hours) on fully dense material, nascent stage sintering (90 to 1,320 seconds) starting with the green compact, and surrogate liquid phase experiments to characterize the WC powder prior to sintering. Quantitative microstructural analysis using intercept length distributions was performed for the long-term sintering. The nascent stage experiments involved the measurement of the specific surface area (S{sub v}) of each type of interface separately allowing the determination of the contribution of each developing entity to the overall microstructural evolution. The VC addition has been found to enhance the breakup of multigrained particles in the earliest stages of sintering, ...

Energy Technology Data Exchange (ETDEWEB)

The Rocky Flats Plant (RFP) generates large volumes of a low level aqueous waste stream high in nitrate salts. The aqueous waste is concentrated by evaporation and then mixed with Portland cement prior to transport and disposal. Planned process upgrades include a new horizontal thin film evaporator. Temperature of brine at discharge end of the new evaporator will be near boiling point. Introduction of hot water to cement can degrade the monolithic waste form. However, the RFP salt waste contains high concentrations of compounds known to retard hydration. This paper discusses impact of introducing high temperature waste to cement. The study evaluated three waste compositions: (1) highest probable nitrate composition, (2) highest probable chloride composition, and (3) current composition. Results showed that compressive strength of final waste form increased with brine temperature, and waste forms from brine at the boiling point exhibited a near doubling of compressive strength when ...

Energy Technology Data Exchange (ETDEWEB)

Westinghouse is currently conducting the pre-application licensing of the International Reactor Innovative and Secure (IRIS). One of the key aspects of the IRIS design is its safety-by-designTM philosophy and within this framework the PRA is being used as an integral part of the design process. The most ambitious risk-related goal for IRIS is to reduce the Emergency Planning Zone (EPZ) to within the exclusion area by demonstrating that the off-site doses are consistent with the US Protective Action Guidelines (PAGs) for initiation of emergency response so that the required protective actions would be limited to the exclusion area. As a first step, a model has been developed to provide a first order approximation of the Large Early Release Frequency (LERF) as a surrogate predictor of the off-site doses. A key-aspect of the LERF model development is the characterization of the possible paths of release. Four main categories have been historically pointed out: (1) ...

Energy Technology Data Exchange (ETDEWEB)

Contaminated wood treatment sites can result in adverse health effects to nearby residents. Environmental exposure can be estimated by measuring concentrations of pollutants in air, water, food, or wipe tests. This environmental exposure value can be used as a surrogate to estimate individual exposure. The objective of this study was to determine whether or not pentachlorophenol (PCP) could be found in potentially exposed residents and if the dioxin levels are consistent with PCP exposure. A further objective of the study was to determine whether or not PAH-DNA adducts could be found in the potentially exposed residents. We present results of biomonitoring studies in residents living near a wood treatment plant that used coal-derived creosote and PCP to process and treat wood for over 100 years. The plant was built in 1904 and used creosote and PCP. Creosote is a complex mixture that contains numerous polycyclic aromatic hydrocarbons (PAHs). PCP is contaminated ...

British Library Electronic Table of Contents (United Kingdom)

Abstract:- Escherichia coli-O157:H7 and-Salmonella-spp. are bacterial pathogens often associated with beef, and cause many cases of foodborne illness each year in the United States. During beef slaughter and processing, these bacteria may spread from the hide or intestines to the carcass. The objective of this research was to investigate the use of naturally occurring compounds citrus essential oils (CEOs) extracted from orange peel to reduce or eliminate these pathogens at the chilling stage of processing, or during fabrication. Brisket flats (used to simulate beef subprimals) were spot inoculated with approximately 6 log of surrogate generic-E. coli-cocktail (previously shown to be identical in growth and survival parameters to-E. coli-O157:H7 and-Salmonella-spp.). Following drying, CEOs...

International Nuclear Information System (INIS)

We examined the spectral behaviors of lasing from a asymmetrically deformed liquid jet (a ? 14 ?m) which is induced by a laterally flowing gas. Th liquid sample was methanols which contains DCM dye. When n distortion is induced, the lasing spectrum appears as two periodic peaks which are corresponding to the resonance modes of cylindrical cavity. As the distortion parameter exceeds about 4%, the lasing spectrum shifts continuously to short wavelength. When the distortion parameter reaches ? 10%, the amount of blue shift was ? 30 nm. The blue shift can be explained as the shift of optimum wavelength of threshold curves. From the absorption and fluorescence curve of liquid sample, we estimated the spoiled Q with the distortion parameter.

International Nuclear Information System (INIS)

We present the design of a diagnostic system to measure electron cyclotron absorption at the second harmonic E-mode resonance in the JET pumped divertor plasma. The diagnostic will measure transmission as a function of frequency along one or more sightlines from which the spatial profile of the n_eT_e product will be deduced. The divertor is briefly described, and the electron cyclotron resonance physics relevant to this measurement is reviewed. The problems of measuring transmission using an oversized transmission system are discussed and the chosen measurement technique, a swept frequency interferometer using a coherent radiation source, is described. A prototype of the instrument has been assembled to test the measurement technique. Some data demonstrating the instrument's characteristics are presented. The nonresonant losses, which may affect the interpretation of the measurement, are also discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

During helium beam fuelling experiments in JET, distinctive anisotropic features have been observed in the velocity distribution function describing both fast and thermal alpha particle populations. During the initial fuelling phase the central helium ion temperature observed perpendicular to the magnetic field is higher than the central electron temperature, while the central helium ion temperature observed parallel to the magnetic field is lower than or equal to the central electron temperature. In order to verify temperature measurements of both perpendicular and parallel lines of sight, other independent methods of deducing the ion temperature are investigated: deuterium ion temperature, deuterium density, comparison with neutron rates and profiles (influence of a possible metastable population of helium). 6 refs., 7 figs.

Science.gov (United States)

This paper presents the experimental results of heat transfer augmentation in an axisymmetric jet impinging normally on a flat plate surface without the requirement of additional pumping power. The present technique of augmentation utilizes only a punched plate with circular holes arranged in a triangular array, fixed parallel to, just in front of the heated target plate. Near the optimum conditions determined, the heat transfer coefficient at the geometrical stagnation point can be increased 4 times. Additional flow visualization study indicates that this augmentation mechanism creates an improved flow field where the punched plate acts as a detached fin, the conductivity of which may be exploited for further augmentation. Besides augmentation, the present investigation foresees the possibility of manipulating the distribution of local heat transfer rate by varying few parameters.

Energy Technology Data Exchange (ETDEWEB)

The alpha-particle confinement of future D-T experiments at JET can be severely degraded by Global Alfven Eigenmodes (AE). Scenarios for the excitation of Alfven Eigenmodes in usual (e.g. D-D) plasmas are proposed, which provide a MHD diagnostic and allow the study of the transport of super-Alfvenic ions. Active studies with separate control of TAE amplitude and energetic particle destabilization, measuring the plasma response, give more information than passive studies, in particular concerning the damping mechanisms. The TAE excitation can be achieved by means of the saddle coil and the ICRH antenna. The experimental method is introduced together with a theoretical model for RF excitation. (authors). 6 refs., 3 figs.

International Nuclear Information System (INIS)

Experiments of plasma nitriding of titanium are carried out by two plasma sources. One is a microwave discharge plasma source under several Torr, and the other is a nitrogen arc jet generated under atmospheric pressure followed by rapid expansion into a gas wind tunnel. The relationship between the surface density of nitrogen atoms in the #alpha#-Ti and various plasma parameters is systematically studied. For the microwave nitrogen plasma, it is found that the effect of the vibration temperature is the most essential for the surface nitriding, whereas the effect of electron temperature, density and rotation temperature is less remarkable. It is also found that the higher vibration temperature of the microwave discharge nitrogen plasma makes the target temperature higher, and consequently, the surface density of atomic nitrogen remarkably increased. However, the effect of target temperature is less remarkable for the arc jet nitrogen plasma.

International Nuclear Information System (INIS)

A particle-laden turbulent reacting flow model is described and applied to in-furnace, dry SO_2 control in boilers. Sulfur capture by calcium-based sorbents is represented by a shrinking core model which accounts for surface areas loss and product layer diffusion. Sorbent particle trajectories and dispersion are followed with cloud statistics in a Lagrangian framework. The turbulent fluid mechanics and chemical reactions are coupled, and solutions obtained for mean and fluctuating velocity, composition, and particle position. Comparisons are made with data from an US EPA laboratory reactor. Practical implications for SO_2 control are examined including the effects of jet velocity, sorbent injection location, boiler load and thermal profiles.

Energy Technology Data Exchange (ETDEWEB)

Blowdown thrust forces and decompression characteristics were evaluated concerning the jet discharge or pipe whip tests with a 4-inch or 6-inch diameter pipe under PWR LOCA or BWR LOCA conditions related to pipe rupture accidents in nuclear power plants. This paper presents experimental evaluations of time-dependent and maximum blowdown thrust forces, and evaluations of decompression characteristics under instantaneous pipe rupture conditions. The following items are discussed: the peak value of the blowdown thrust force, the jet thrust coefficient for the maximum blowdown thrust force, the pressure recovery after break, and the relationship between the pressure undershoot of the sudden decompression and the decompression rate.

Energy Technology Data Exchange (ETDEWEB)

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions. Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.

Energy Technology Data Exchange (ETDEWEB)

The fuel composition heterogeneity effect on reactor performance parameters was assessed by refueling simulations for three DUPIC fuel options of fuel composition heterogeneity control: the fissile content adjustment, the reactivity control by slightly enriched and depleted uranium, and the reactivity control by natural uranium. For each DUPIC fuel option, the simulations were performed using 30 heterogeneous fuel types which were determined by the agglomerative hierarchical clustering method. The heterogeneity effect was considered during the refueling simulation by randomly selecting fuel types for the refueling operation. The refueling simulations of the heterogeneous core have shown that the key performance parameters such as the maximum channel power (MCP), maximum bundle power (MBP), and channel power peaking factor (CPPF) are close to those of the core ...

International Nuclear Information System (INIS)

A new procedure of fuel layering for the Fast Ignition Realization Experiment (FIREX) target is proposed. A conical laser guide heating technique was experimentally demonstrated in principle as the followings. It employed the target consisting of a polystyrene (PS) shell, a fill tube and a conical laser guide. At first, liquid fuel was fed into the shell and existed around the conical laser guide because the surface tension of the fuel must cause it. Then, it was solidified. The laser light provided a heat source to the conical laser guide so that the solid fuel was moved to the other interior of the shell. This process resulted in missing solid fuel around the conical laser guide. To fill the vacant space, liquid fuel was added as temperature was raised to the melting point. After the liquid fuel addition, temperature was lowered to the ...

Energy Technology Data Exchange (ETDEWEB)

Fuel elements used in the ORR whole-core LEU fuel demonstration have been gamma-scanned to determine axial distributions of UZLa and TXCs fission product activities. This data has been analyzed to determine cycle-averaged fuel element powers, residual STVU masses, and burnups of discharged fuel elements. Methods used to analyze the data are discussed and results are presented for the LEU fuel elements. Measured and calculates fuel element powers agree to within 5%, residual STVU masses to within 2%, and burnups to within 3%. These results are somewhat preliminary and await improved burnup calculations and independent calibration data to be based on the destructive analyses of a number of irradiated fuel elements. 4 refs., 7 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This paper gives details of the development of the Wartsila 32DF duel-fuel lean-burn engine that can burn liquid or gaseous fuels, and reports on the installation of four of the engines in Turkey. The combustion process, and the design of the gas admission, pilot fuel, cylinder control, air-fuel control, and engine control and monitoring systems are described. The advantages of the engine are discussed.

International Nuclear Information System (INIS)

MOX fuel has been one of the mature nuclear fuels which can be used in light water nuclear power plant now. The development status in this domain in foreign countries, the major influence of MOX fuel on reactor performance and the countermeasures are introduced in this paper. The application of MOX fuel in China's PWR is discussed in the end. (authors)

International Nuclear Information System (INIS)

The fuel management study on 18-months fuel cycle project is introduced for Daya Bay Nuclear Power Station. Station from the selection of the objective of fuel management for 18-months cycle, the method used and the analysis done are explained in detail to reach the final loading pattern chosen