Energy Technology Data Exchange (ETDEWEB)

This paper discusses the application of a Computational Fluid Dynamics (CFD) code (FLUENT) to predict temperature and velocity profiles, and particle trajectories in an industrial fired by a low NO{sub x} pulverized coal swirl burner. The predictions of the code were compared to experimental measurements of gas temperature, particle size distribution, and particle velocities. The diagnostics employed were a suction pyrometer and a Particle Counter Sizer Velocimeter Probe (PCSV-P). Good agreement was found between the temperature predictions and the measurements. In situ particle size distributions were predicted accurately using the Baum and Street model with a swelling factor of zero. The numerical modeling indicated that the Type II flow issued from the burner could be transformed into Type III flow, by eliminating ...

Science.gov (United States)

... THESIS PARTICLE-SIZING SYSTEM FOR SCANNING ELECTRON MICROSCOPE IMAGES OF SOLID-PROPELLANT COMBUSTION EXHAUST ...

UK PubMed Central (United Kingdom)

Dosimetry parameters such as deposition, clearance, retention, and translocation and dissolution of inhaled particles in and to different lung compartments may be important for the persistence of particles...Full Text Available

International Nuclear Information System (INIS)

Effect of globular structure parameters - size of primary #alpha#-phase particles (bsub(I)), thickness and amount of plates of secondary #alpha#-phase (bsub(II), #gamma#sub(II#alpha# )) - on a complex of mechanical properties (#sigma#sub(#beta#), S, phi, asub(H), asub(T), Ksub(Q), #sigma#sub(-1), #sigma#_1_0_0"4"5"0, #sigma#sub(0.2/100)) of VT3-1 (#alpha#+#beta#)-titanium alloy is studied. The dependences obtained allow one to determine globular structure parameters, providing necessary mechanical properties. In combination with data on the effect of thermal treatment conditions on structure parameters, results obtained in the paper may be used for structure control to increase a level of required characteristics.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A characterization study was performed on monosodium titanate (MST) particles to determine the effect of high shear forces expected from the In-Tank Precipitation (ITP) process pumps on the particle size distribution. The particles were characterized using particle size analysis and scanning electron microscopy (SEM). No significant changes in particle size distributions were observed between as-received MST and after 2--4 hours of shearing. Both as-received and sheared MST particles contained a large percentage of porosity with pore sizes on the order of 500 to 2,000 Angstroms. Because of the large percentage of porosity, the overall surface area of the MST is dominated by the internal surfaces. The uranium and plutonium species present in the waste solution will have access to ...

Energy Technology Data Exchange (ETDEWEB)

There has been considerable interest in producing and studying nanoparticle materials because of the effect of size on their structure, physical and chemical structure. Most studied nanoparticle semiconductors belong to the II-VI group, as they are relatively easy to synthesize and are generally prepared as particulates or in thin film form. Among II-VI compounds, CdS is one of the most studied materials. There are different ways to synthesize CdS nanoparticles such as colloidal particles, chemical decomposition, sol-gel, gas evaporation, magnetron sputtering, electrostatic deposition, and etc. {gamma}-irradiation is one of the effective methods for synthesis of nanomaterials. These nonomaterials have been extensively used in the preparation of nanocrystalline metals, metal oxides, and metal-polymer composites. However, The preparation of CdS nanoparticle and CdS/ polyacrylonitrile nanocomposite by ...

UK PubMed Central (United Kingdom)

This work investigates the effect of excipient particle size on compaction properties of brittle, plastic and viscoelastic materials with and without added lubricants. Sieve cuts of Microcrystalline...Full Text Available

International Nuclear Information System (INIS)

Processes of production and purification (necessary for fabricating fuel elements) of powdery uranium dioxide with particle size up to 1000 #mu#m and more have been studied. Developed is continuous process of UO_2 production with above particle size by converting uranium hexafloride into UO_2 solid particles in fluidized bed while their interaction with water vapor and hydrogen on the uranium dioxide nucleus material. The method allows to conduct continuous selection from the apparatus of UO_2 powder fraction with particle size near 1000 #mu#m without nucleus material additional feed.

Energy Technology Data Exchange (ETDEWEB)

The effect of WC particle size with the addition of VC as a grain growth inhibitor was investigated during the liquid phase sintering of WC-Co system. With increasing WC particle size at the same VC content, the effect of grain growth inhibition was increased. Also, with increasing the VC content, the grain shape of WC was changed from the faceted shape to the distorted shape, and the step density of the WC grain was increased. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Samarium cobaltite ceramic perovskites, with and without platinum particles dispersion, are possible candidates as electrode for electrochemical conversion of hydrocarbon and for intermediate temperature solid oxide fuel cells (ITSOFC). In this work, samarium cobaltites were synthesized by the combustion method using cobalt, and samarium nitrates as cation precursors and urea as fuel. For containing-platinum compositions Pt (II) acetyl acetonate was also employed as precursor. The effect of Sr on the phase formation and its electrical behavior is also studied. Specific surface area (BET), SEM-EDX, TEM and XRD analysis are used to characterize the powders obtained. Powders were pressed into pellets and sintered in air in the temperature range of 1200 -1400 C. Electrical impedance spectroscopy studies (EIS) are performed on sintered samples. The as-prepared powders showed an amorphous structure and by TEM a very small ...

Energy Technology Data Exchange (ETDEWEB)

Particle shape is an important parameter in numerous civil, environmental, and petroleum engineering applications. In ground-water flow, the shape of individual particles comprising the soil affects the soil`s pore size distribution and, hence, the important flow characteristics such as hydraulic conductivity and headloss. A model for delineating the relative importance of particle size, particle shape, and porosity, (and their interactions), in explaining the variability of hydraulic conductivity of a granular porous medium is developed and tested. Three types of porous media are considered in this work: spherical glass beads; granular sand; and irregularly shaped, shredded glass particles. A reliable method for quantifying the three-dimensional shape and packing of large samples of irregular particles based on their ...

Energy Technology Data Exchange (ETDEWEB)

It is shown that observations of the lithium isotope ratio in high surface temperature Population II stars may be critical to cosmological nucleosynthesis models. In particular, decaying particle scenarios as derived in some supersymmetric models may stand or fall with such observations. 18 references.

International Nuclear Information System (INIS)

Runit Island on Enewetak Atoll was very heavily impacted by the U.S. nuclear testing campaign in the northern Marshall Islands (1946-58). The primary source of contamination on Runit Island was the 1958 Quince safety test where a large quantity of device plutonium (Pu) was scattered over the area near the GZ. A second low-yield device was detonated on the same site 10 days later, further disturbing the soil and leaving behind a very heterogeneous pattern of contamination including milligram-size particles of plutonium. A limited cleanup of the Fig-Quince zone was carried out in 1979. During this period, the effectiveness of the cleanup operations was primarily evaluated on the basis of bulk soil concentration data with little consideration given to the heterogeneity and long-term material-, biological-, and environmental-specific impacts of residual high activity (hot) particle contamination. The aim of the present study ...

British Library Electronic Table of Contents (United Kingdom)

An ultrafine-grained ferrite/cementite (UGF/C) steel with a local high density of cementite particles was fabricated through caliber-warm-rolling followed by annealing and resulted in a bimodal-sized microstructure. The characteristic bimodal-sized microstructure was attributed to the original ferrite-pearlite structure and cementite spacing, and reflected the original ferrite-pearlite structure. The smaller-sized clusters corresponded to the former pearlite regions and the larger-sized clusters to the proeutectoid ferrite regions. The cementite particles naturally localized within the former pearlite region. Most of the ferrite coarsening did not occur until the cementite particle spacing reached a critical value. The UGF/C microstructure with a bimodal grain size showed a yield strength ...

International Nuclear Information System (INIS)

Structure and magnetic properties of the thermal decomposition products of Fe(III(Co(II) acrylate complex were analysed. The crystalline phases, which were found in the fully processed material, at 643 K, were Fe_3O_4, CoFe_2O_4 and CoO and had a mean particle size of about 30 nm. In the intermediate stages of the thermolysis iron was present in a form of Fe"I"I"I (trivalent low-spin iron), Fe"2"+ (divalent high-spin iron), and Fe_3O_4. The coercivity and remanence were measured versus temperature in the range of 5-300 K, in 1.1 T applied field. Both _MH_c and M_r, decreased showing room temperature values of 0.038 T and 7.49 mT, for coercivity and remanence, respectively. At temperatures below 200 K the hysteresis loops were asymmetrical, opened and shifted towards negative field values. (author)

Energy Technology Data Exchange (ETDEWEB)

In this article a production method of a magnetorheological suspension composed with silicon steel particles of size 0.1-0.15 mm and 4% silicon content is described. Steel particles were dispersed in a conducting carrier of a by mixture of graphite particles with size 2-5 {mu}m and cedar wood oil. The filling factor of the suspension with the silicon steel particles and with graphite particles amounted to 0.25-0.40. Samples of this suspension were placed in a rectangular vessel with electrodes and used for the investigation of the Hall effect in magnetic field with induction 0-8 T, generated by Bitter-type magnet. A non-linear dependence of Hall voltage on the induction of the applied magnetic field and a hysteresis loop of this voltage in the shape of inclined digit eight were found. The causes of the observed effects is the ordering of ...

Energy Technology Data Exchange (ETDEWEB)

Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.

International Nuclear Information System (INIS)

One of several methods to build YSZ electrolyte of SOFC is plasma spraying. This system heats particle to a melting point and then pushing them into target and forming a deposition. This paper presents heating studies of YSZ particle in plasma jet. By simple model it is shown that the required time such those YSZ particle with grain size of 50 ?m to be melt is around 12 x 10-4 second. (author)

Science.gov (United States)

... being pulled out of water, the movement is restricted ... This heating depended on the particle size ... hydrometeor injection into the upper tropopause. ...

Science.gov (United States)

dust measured in the Arabian Gulf region during UAE2 and examine the hypothesis that ... [8] UAE2 took place in the southern Arabian Gulf region in August and ...

Energy Technology Data Exchange (ETDEWEB)

A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions.

Energy Technology Data Exchange (ETDEWEB)

The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 {micro}m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-{micro}m quartz particles; particles {ge}150 {micro}m formed clusters. Particles of 5 {micro}m completely dissolved by 900 C whereas particles {ge}150 {micro}m did not fully dissolve even when the temperature ...

Energy Technology Data Exchange (ETDEWEB)

The high temperature abrasive wear resistant of the composites with different Al{sub 2}O{sub 3} volume fractions, particle coating and size were investigated and the failure action of composites under different conditions at high temperature was analyzed. The results showed that the high temperature abrasive wear resistant of composite with Ni coating and wide size and 39% volume fraction of particle is the best among all composites examined. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Often, lifetime data come from experiments where failure times are grouped. The Weibull distribution is a popular distribution for modeling failure times. Maximum likelihood estimation (MLE) has outstanding large sample properties for the Weibull distribution. This article evaluates small sample properties of MLEs for grouped data. We evaluate sample size requirements for MLE asymptotic properties to take effect. We compare type I and type II censoring for pooled experiments and conclude that bias for the shape parameter estimate can be alarmingly high especially for type II censored data. Finally, we investigate the benefits of the pooled analysis.

Energy Technology Data Exchange (ETDEWEB)

In this paper, we investigated the effect of alcohol solvents (ethanol, n-propanol, and n-butanol) and isomeric alcohol solvents (iso-propanol, iso--butanol, and tert-butanol). In addition, we observed the effect of the mixed alcohol solvents on the particle formation as using a mixture od ethanol and butanol at a ratio od 30/70, 50/50 and 70/30 vol %, respectively. In case of ethanol solvent, particle size of silica showed the smallest and the narrowest size distribution among the various solvent. On the contrary, for the n-butanol solvent, largest broad distribution of particle size was observed. For the synthesis of particles having better spherical morphology and less agglomeration, alcohol solvent having no branches was considered appropriate. When mixed alcohol solvents were used, large silica particles with narrow ...

DEFF Research Database (Denmark)

Zinc oxide (ZnO) and alumina (Al2O3) particles are synthesized by the combustion of their volatilized acetylacetonate precursors in a premixed air-methane flame reactor. The particles are characterized by XRD, transmission electron microscopy, scanning mobility particle sizing and by measurement of the BET specific surface area. Pure (?-)alumina particles appear as dendritic aggregates with average mobile diameter 43-93 nm consisting of partly sintered, crystalline primary particles with diameter 7.1-8.8 nm and specific surface area 184-229 m2/g. Pure zinc oxide yields compact, crystalline particles with diameter 25-40 nm and specific surface area 27-43 m2/g. The crystallite size for both oxides, estimated from the XRD line broadening, is comparable to or slightly smaller than the primary particle ...

British Library Electronic Table of Contents (United Kingdom)

Blood kinetics and tissue distribution of 20, 80 and 110 nm silver nanoparticles were investigated in rats up to 16 days after intravenous administration once daily for 5 consecutive days. Following both single and repeated injection, silver nanoparticles disappeared rapidly from the blood and distributed to all organs evaluated (liver, lungs, spleen, brain, heart, kidneys and testes) regardless of size. The 20 nm particles distributed mainly to liver, followed by kidneys and spleen, whereas the larger particles distributed mainly to spleen followed by liver and lung. In the other organs evaluated, no major differences between the sizes were observed. Size-dependent tissue distribution suggests size-dependent toxicity and health risks. Repeated administration resulted in accumulation in li...

International Nuclear Information System (INIS)

Olfactory tract has been demonstrated to be an important portal for inhaled solid nanoparticle transportation into the central nervous system (CNS). We have previously demonstrated that intranasally instilled Fe_2O_3 nanoparticles could transport into the CNS via olfactory pathway. In this study, we investigated the neurotoxicity and size effect of repeatedly low-dose (130 #mu#g) intranasal exposure of nano- and submicron-sized Fe_2O_3 particles (21 nm and 280 nm) to mice. The biomarkers of oxidative stress, activity of nitric oxide synthases and release of monoamine neurotransmitter in the brain were studied. Our results showed that significant oxidative stress was induced by the two sizes of Fe_2O_3 particles. The activities of GSH-Px, Cu,Zn-SOD, and cNOS significantly elevated and the total GSH and GSH/GSSG ratio significantly decreased in the olfactory bulb and hippocampus after ...

Energy Technology Data Exchange (ETDEWEB)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the ...

Energy Technology Data Exchange (ETDEWEB)

We demonstrate a preparative method which produces highly-monodisperse Pt-nanoparticles of tunable size without the external addition of seed particles. Hexachloroplatinic acid is dosed slowly to an ethylene glycol solution at 120 C and reduced in the presence of a stabilizing polymer poly-N-vinylpyrollidone (PVP). Slow addition of the Pt-salt first will first lead to the formation of nuclei (seeds) which then grow further to produce larger particles of any desired size between 3 and 8nm. The amount of added hexachloroplatinic acid precursor controls the size of the final nanoparticle product. TEM was used to determine size and morphology and to confirm the crystalline nature of the nanoparticles. Good reproducibility of the technique was demonstrated. Above 7nm, the particle shape and morphology changes suddenly indicating a change in the ...

Energy Technology Data Exchange (ETDEWEB)

In the safety assessment of a potential repository for spent nuclear fuel, it is important to assess the consequences of a hypothetical leak of radionuclides through the seabed and into a waterborne transport phase. Radionuclides adsorbed to sediment particles may be transported great distances through the processes of sedimentation and resuspension. This study investigates the transport patterns of sediment particles of two different sizes, released in the Forsmark and Laxemar area. The results show that the closed waters around Forsmark to a higher degree makes the particles stay in the area close to the release points

International Nuclear Information System (INIS)

In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe"3"+ and Fe"2"+) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.

Energy Technology Data Exchange (ETDEWEB)

This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric lengths of the splat and crater scale linearly with the diameter of the impacting ...

British Library Electronic Table of Contents (United Kingdom)

Fatigue crack growth tests of three ferrite-pearlite steels with different size and spacing of pearlite particles, which were uniformly distributed in the ferrite matrix, were carried out to investigate the effect of microstructure on fatigue crack growth behavior in the Paris regime. The fatigue crack growth rates for the three materials did not coincide with each other, even when the crack growth curves were arranged by the effective stress intensity factor range. From in situ observations, crack tip stress shielding phenomena, such as interlocking and branching, were found on the crack wake, which enhanced fatigue crack growth resistance. A small size and spacing of pearlite particle seemed to induce small but frequent crack deflections, which resulted in crack closure phenomena. On the...

British Library Electronic Table of Contents (United Kingdom)

To investigate the feasibility of using aged municipal solid waste as farmland soil, it is essential to study its nutritive compositions for plant growth. Previous studies have demonstrated that the properties of different particle-size aged refuse are very different, therefore, the present study was conducted to evaluate the adequacy of three elements (N, P, K) and the fractionation of inorganic P in the aged refuse with a particle-size distribution of 900 to 300, 300 to 150, 150 to 105, 105 to 90 and 90 to 0mm. The results indicate that (1) total quantities of N, P, K were much larger than that in the general soil and the quantities of available N, P and K were also adequate; (2) total content of P was sufficient, but the ratio of available-P to total P was not high enough; (3) with the ...

Energy Technology Data Exchange (ETDEWEB)

The burning characteristics of fuel droplets containing nano and micron-sized aluminum particles were investigated. Particle size, surfactant concentration, and the type of base fluid were varied. In general, nanosuspensions can last much longer than micron suspensions, and ethanol-based fuels were found to achieve much better suspension than n-decane-based fuels. Five distinctive stages (preheating and ignition, classical combustion, microexplosion, surfactant flame, and aluminum droplet flame) were identified for an n-decane/nano-Al droplet, while only the first three stages occurred for an n-decane/micron-Al droplet. For the same solid loading rate and surfactant concentration, the disruption and microexplosion behavior of the micron suspension occurred later with much stronger intensity. The intense droplet fragmentation was accompanied by shell rupture, which caused a massive explosion of ...

UK PubMed Central (United Kingdom)

The objective of this work was to evaluate the physical properties and in vivo circulation of chitosan (CH)-coated liposomes of mitoxantrone (MTO). Changes in particle size and zeta...Full Text Available

Science.gov (United States)

Feb 15, 2008 ... hydrological properties (e.g., hydrometeor budgets, cloud ice/water, transports ... cloud fraction, mass and particle size. In combination, these .... anomaly in the LS is not simply due isentropic movement of water vapor relative ...

British Library Electronic Table of Contents (United Kingdom)

This research aims to investigate the effects of chemical blowing agent (CBA) contents and particle sizes on the properties of foamed poly(vinyl chloride) (PVC)/rice hull (RH) composites. Fine particles of azodicarbonamide (AC) at 5, 8, 11 and 22mm were modified with 20% by weight of ZnO and used at 0-3.0% by weight. The average cell size and density of the PVC/RH foamed profiles were reduced as the content of modified azodicarbonamide (mAC) increased. Larger mAC particles lowered the density more effectively. Maximum reduction of density by 46% was achieved when mAC 22mm was applied at 2.0% by weight. Larger blowing particles led to PVC/RH foam with greater flexural modulus and strength. Greater impact strength, observed when 5mm mAC was applied, resulted from the rather thick cell wall c...

British Library Electronic Table of Contents (United Kingdom)

Methods of X-ray diffraction and transmission electron microscopy were used to study the microstructure of dispersion-strengthened Cu-Al2O3 nanocomposites obtained by the method of simultaneous deposition of Cu and Al2O3 from the vapor phase. The effect of the size of particles of the oxide (Al2O3) and of their content on the electrical resistance of the composite has been considered. The results obtained make it possible to suppose that the main structural factor that determines the electrical resistance of the composite are nanodispersed particles of Al2O3 with a size of less than 20 nm.

British Library Electronic Table of Contents (United Kingdom)

Doped ultrafine silicon dioxide powder with a narrow particle size distribution was obtained by RF discharge-stimulated dichlorosilane (SiH2C) oxidation at a low pressure using isobutylene as the combustion inhibitor and chromium hexacarbonyl (Cr(CO)6) as the dopant. The formation and morphology of the ultrafine particles are governed by the parameters of the RF discharge and by the chemical mechanism of the combustion reaction yielding the aerosol. Submicron-sized filamentous carbon structures can be obtained by isobutylene decomposition under spark discharge conditions in the presence of a molybdenum metal catalyst.

International Nuclear Information System (INIS)

Adult and newborn rats were exposed to "2"3"9PuO_2 aerosols of four different size distributions. Rats of both ages were killed at intervals between 1 hr and 60 days postexposure. There were marked age- and particle-related size differences in deposition, although retention was similar throughout. The differences in deposition are attributable to relatively greater deposition of larger particles in the upper respiratory tracts of newborns.

Energy Technology Data Exchange (ETDEWEB)

Reductive quenching of two photoexcited ruthenium(II) complexes by an anionic electron donor, 2,2{prime}-azinobis(3-ethyl-benzothiazoline-6-sulfonate) (ABTS{sup 2{minus}}), in aqueous solution was examined by laser flash photolysis before and after adding positively charged colloidal (250-{angstrom} diameter) alumina-coated silica particles. The kinetics and quantum yields of electron transfer with an anionic sensitizer, RuL{sub 3}{sup 4{minus}} (L = bathophenanthroline disulfonate), and a cationic one, Ru(bpy){sub 3}{sup 2+} (bpy = 2,2{prime}-bipyridine), were compared. Coadsorption of ABTS{sup 2{minus}} and RuL{sub 3}{sup 4{minus}} by the particles greatly enhanced the rate of quenching such that only the reaction occurring on the surfaces of the particles was observed. Electron transfer from ABTS{sup 2{minus}} to RuL{sub 3}{sup 4-*} occurred by a static (nondiffusional) process, and the quenching ...

Energy Technology Data Exchange (ETDEWEB)

Boron Neutron Capture Therapy (BNCT) is a promising binary treatment modality for high-grade primary brain tumors (glioblastoma multiforme, GM) and other cancers. BNCT employs a boron-10 containing compound that preferentially accumulates in the cancer cells in the brain. Upon neutron capture by {sup 10}B energetic alpha particles and triton released at the absorption site kill the cancer cell. In order to gain penetration depth in the brain Fairchild proposed, for this purpose, the use of energetic epithermal neutrons at about 10 keV. Phase I/II clinical trials of BNCT for GM are underway at the Brookhaven Medical Research Reactor (BMRR) and at the MIT Reactor, using these nuclear reactors as the source for epithermal neutrons. In light of the limitations of new reactor installations, e.g. cost, safety and licensing, and limited capability for modulating the reactor based neutron beam energy spectra alternative neutron sources are being ...

Energy Technology Data Exchange (ETDEWEB)

Biosorption of cadmium (Cd), cobalt (Co), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn) by six fractions of particle sizes, ranging from 0.063 to 1.4 mm of dry marine algal biomass of Sargassum fluitans and Ascophyllum nodosum, is examined. Equilibrium metal uptake by larger particles was higher than that by smaller particles in the order of Pb > Cd > Cu > Co > Zn > Ni for both biomass types, with S. fluitans sorbing slightly more than A. nodosum. Uptakes of metals ranged from the highest, q{sub max} = 369 mg Pb/g (particle size 0.84-1.00 mm), to the low Zn and Ni uptakes, q{sub max} = 77 mg/g (size 0.84-1.00 mm) for S. fluitans. A. nodosum adsorbed metals in the range from q{sub max} = 287 mg Pg/g (particle size 0.84-1.00 mm) to q{sub max} = 73 mg Zn/g ...

International Nuclear Information System (INIS)

The CDF II eXtremely Fast Tracker (XFT) is the trigger processor which reconstructs charged particle tracks in the CDF II central outer tracking chamber. The XFT tracks are also extrapolated to the electromagnetic calorimeter and muon chambers and are associated to electromagnetic clusters and muon stubs to generate trigger electron and muon candidates. The steady increase of the Tevatron instantaneous luminosity and the resulting higher occupancy of the chamber demanded an upgrade of the original system, which performed tracking only in the transverse plane of the chamber and was consequently affected by a significant level of fake tracks. In the upgraded XFT, tracking is reinforced by using additional data from the stereo layers of the chamber to reduce the level of fake tracks and to perform three-dimensional track reconstruction. A review of this upgrade is presented.

International Nuclear Information System (INIS)

The formation and growth of silicon-nanoparticles from silane in a microwave reactor was investigated. Experiments were performed for the following conditions: precursor concentration 380-2530 ppm, pressures of 20-30 mbar, microwave powers 120-300 W. The formed particles were examined in-situ with a particle mass spectrometer. Additionally, particles were collected on grids and analyzed by transmission electron microscopy, X-ray diffraction, and by determining the specific surface area by BET. The particle size was found to be in the range of 5-8 nm in diameter. A simple model was used to simulate the particle formation processes taking place inside the reactor. The microwave energy coupled into the reactor flow was treated as a spatially distributed energy source resulting in a local temperature increase. The particles were assumed to have ...

Energy Technology Data Exchange (ETDEWEB)

The use of filters of activated-charcoal particles in drinking-water purification plants assists in the elimination of organic micropollutant substances. The authors report on a study which sought to investigate the mechanism of organic matter; they describe the experimental programme, which used different size ranges of mineral-based activated charcoal, present the experimental findings and discuss the results. 16 references.

International Nuclear Information System (INIS)

Iron oxide as sintering aid to Ce-TZP ceramics produces a beneficial effect on the tetragonal phase stabilization. It was found that ceria powder particle size of 2,0 #mu#m turns the grain-boundary electrical conductivity higher than ceria powder of smaller grain size. (author)

International Nuclear Information System (INIS)

Effect of proton backscattering on inelastic pd-scattering is discussed in detail. The discussion was carried out on the basis of interaction mechanism if bombarding particle with flucton. It is noted that fluctons are assumed presently as time multiquark formations of nuclear matter with the size of nucleon size order and density above nucleon one. 35 refs., 10 figs.

Energy Technology Data Exchange (ETDEWEB)

Flow fields, temperature distributions, and particle trajectories in a 2-stage entrained-flow gasifier are calculated using a CFD code, FLUENT. Realizable k- {epsilon} model is used as a turbulent model. Because of swirling flow there appear recirculation regions near the burners. The characteristics of flow fields and temperature distributions in the gasifier are dependent on the swirl number of the system. Mean residence time of the particles in the reductor is inversely proportional to particle size, particle density and swirl number. As the swirl number is increasing, the particles injected from the combustor burners approach the wall near the combustor burners, which prevents the particles from entering the reductor and thus attaching the reductor wall. If the lower combustor burner angle is larger than the higher combustor burner angle ...

International Nuclear Information System (INIS)

The powder particle size, D, influences the creep behaviour of Al-Cr-Zr alloys. The alloy studied in this work, Al-5Cr-2Zr (mass%), was prepared by argon atomization. Three size fractions of powder particles were selected: 24-50 #mu#m, 50-100#mu#m and 100-200 #mu#m in diameter. They were consolidated by extrusion. Independently of D, the flow behaviour of the alloy can be described by the power law equation. As test temperature increases, the stress exponent n decreases up to a value close to 5. A decrease of D causes an increase of n and delays the alloy degradation at high temperature. (Author) 11 refs.

British Library Electronic Table of Contents (United Kingdom)

This paper demonstrates a proof-of-concept approach for encapsulating the insulin and Fe3O4 nanoparticles into size-controllable alginate microcapsules utilizing the electrostatic droplets (ESD) technique. We have established that the combination of ESD and external gelation is quite effective in producing uniform-sized polymer particles. In addition, using the external gelation technique, the droplets containing a sodium-alginate were gelled in situ by immersion in Ca2+, Ba2+, or Cu2+ ions for a few minutes. The results show that different-type divalent cations caused various surface features to appear on the microcapsules (e.g., cracking, orange peel, pitting, splitting, wrinkling, etc.). The particle size can be adjusted from a few micrometers to ca. 1,000??m by electrostatic force. The...

Energy Technology Data Exchange (ETDEWEB)

This invention relates with a pot-type catalyst carrier which excels as a catalyst carrier when such heavy oils as ordinary pressure distillation residue, oil sand oil, and shale oil are decomposed or treated by hydrogenation. The conventional pot-type carrier is produced by dropping a small drop of a slurry (containing a catalyst component) onto a particle bed and drying it. But the demerit is a large particle size and less catalyst activity or strength. In this invention, a mixture of such carrier components as allophane, red mud, bauxite and latellite, etc.. 60 - 80 weight parts. and a binder 20 - 40 weight parts is added with water to form a slurry of 10 - 30 weight% solid concentration. Slurry is wet-crushed to make the average particle size 0.6 - 2.0 micron, then spray-dried and burned to obtain a pot-type catalyst carrier with average particle ...

Energy Technology Data Exchange (ETDEWEB)

Background: The difficulty of directly measuring cellular dose is a significant obstacle to application of target tissue dosimetry for nanoparticle and microparticle toxicity assessment. As a consequence, the target tissue paradigm for dosimetry and hazard assessment of nanoparticles has largely been ignored in favor of using metrics of exposure (e.g. ?g particle/mL culture medium, particle surface area/mL, particle number/mL). We have developed a computational model of solution particokinetics (sedimentation, diffusion) and dosimetry for non-interacting spherical particles and their agglomerates in monolayer cell culture systems. Particle transport to cells is calculated by simultaneous solution of Stokes Law (sedimentation) and the Stokes-Einstein equation (diffusion). Results: The In vitro Sedimentation, Diffusion and Dosimetry model (ISDD) was tested against measured transport ...

Energy Technology Data Exchange (ETDEWEB)

A considerable fraction of radioactivity entering the environment from different nuclear events is associated with particles. The impact of these events can only be fully assessed where there is some knowledge about the mobility of particle bound radionuclides entering the environment. The behavior of particulate radionuclides is dependent on several factors, including the physical, chemical and redox state of the environment, the characteristics of the particles (e.g., the chemical composition, crystallinity and particle size) and on the oxidative state of radionuclides contained in the particles. Six plutonium-containing particles stemming from Runit Island soil (Marshall Islands) were characterized using non-destructive analytical and microanalytical methods. By determining the activity of {sup 239,240}Pu and {sup 241}Am isotopes from ...

Energy Technology Data Exchange (ETDEWEB)

Anthropogenic sulfate aerosol, together with particles from biomass burning, may significantly reduce the climatic warming due to man-made greenhouse gases. The radiative forcing of aerosol particles is based on their ability to scatter and absorb solar radiation (direct effect), and on their influences on cloud albedos and lifetimes (indirect effect). The direct aerosol effect depends strongly on the size, number and chemical composition of particles, being greatest for particles of 0.1-1 {mu}m in diameter. The indirect aerosol effect is dictated by the number of particles being able to act as cloud condensation nuclei (CCN). For sulfate particles, the minimum CCN size in tropospheric clouds is of the order of 0.05-0.2 {mu}m. To improve aerosol parameterizations in future climate models, it is required that (1) both ...

Energy Technology Data Exchange (ETDEWEB)

The influence of location of airborne particle source, ventilation rate, air inlet size, supply air velocity, air outlet location, and heat source on the distributions of airborne particle concentration and draught risk in an operating room is investigated. The investigation is carried out by using a flow program with the k-[epsilon] model of turbulence. Based on a standard case, five cases, each with one changed parameter, are computed, and the detailed field distributions of air velocity, temperature, airborne particle concentration, and draught risk are presented. The parametric study concludes that, for a better air quality and thermal comfort, it is desirable to use a higher inflow rate, a larger inlet area, and a uniform velocity profile of supply air. Outlet location and heat source have little influence on the distributions of the particle concentration in the room. It has ...

Energy Technology Data Exchange (ETDEWEB)

Main results are summarised for a project carried out with the aim of increasing the knowledge of relations between handling characeristics and properties such as moisture content, particle size and shape etc. Handling characteristics that were studied: angle of repose, friction between fuel and different surfaces, the fuel`s tendency to bridge across openings, and its freezing characteristics. Some forty solid biomass fuels were studied, mainly wood fuels, with particle sized from 1 to 200 mm. New methods were developed for measurement of bridging across openings and freezing characeristics. The angle of repose varied between 25 and 55 deg. The particle shape had a significant influence, a high ratio of length/thickness gave a high angle of repose. When the fuel moisture content was increased the angle of repose first increased, then decreased, and finally increased again. The ...

Energy Technology Data Exchange (ETDEWEB)

High resolution imagery of the clumpy irregular galaxy Mkn 325 shows that some clumps have sizes approximately 300 pc while some may still be unresolved and approximately < 100 pc. In spite of dimensions comparable to - or even smaller than - those of the giant H II complex 30 Doradus, one clump has a star formation rate 100 times higher.

International Nuclear Information System (INIS)

We have fabricated nanometer-spaced electrodes on electron-transparent silicon nitride membranes. A thin Cr/Au layer is evaporated on the backside of the membrane which serves as a gate electrode. Using these devices, we have performed three-terminal electron transport measurements on gold nano-particles at liquid helium temperature. Coulomb Blockade features have been observed and the capacitance to the gate has been extracted. After transport measurements, the Cr/Au back gate is removed and the devices are inspected with a transmission-electron microscope (TEM). TEM inspection reveals the presence of a few nano-particles in the nanogap, which is in agreement with the transport measurements. In addition, the nano-particle size as observed by TEM coincides with the one estimated from the gate capacitance value.

International Nuclear Information System (INIS)

Reactions of reducing species from acetonitrile media with silver iodide particles (#approx#25-angstrom diameter) have been investigated by pulse radiolysis techniques. Injection of electrons into these ultrasmall particles leads to transient bleaching of the adsorption of AgI at wavelengths close to the onset of absorption (#approx#400 nm) with the concomitant reduction of AgI to metallic silver. The reduction of Ag"+ ions and formation of silver atoms and/or dimeric Ag_2 molecules on three different size AgI particles (#approx#100, 35, and #approx#25 angstrom) have also been examined by picosecond laser spectroscopy.

CERN Document Server

We have developed a simulation code with the techniques which enhance both spatial and time resolution of the PM method for which the spatial resolution is restricted by the spacing of structured mesh. The adaptive mesh refinement (AMR) technique subdivides the cells which satisfy the refinement criterion recursively. The hierarchical meshes are maintained by the special data structure and are modified in accordance with the change of particle distribution. In general, as the resolution of the simulation increases, its time step must be shortened and more computational time is required to complete the simulation. Since the AMR enhances the spatial resolution locally, we reduce the time step locally also, instead of shortening it globally. For this purpose we used a technique of hierarchical time steps (HTS) which changes the time step, from particle to particle, depending on the size of the cell in ...

British Library Electronic Table of Contents (United Kingdom)

We report a solution-phase synthetic route to copper nanoparticles with controllable size and shape. The synthesis of the nanoparticles is achieved by the reduction of copper(II) salt in aqueous solution with hydrazine under air atmosphere in the presence of poly(acrylic acid) (PAA) as capping agent. The results suggest that the pH plays a key role for the formation of pure copper nanoparticles, whereas the concentration of PAA is important for controlling the size and geometric shape of the nanoparticles. The average size of the copper nanoparticles can be varied from 30 to 80 nm, depending on the concentration of PAA. With a moderate amount of PAA, faceted crystalline copper nanoparticles are obtained. The as-synthesized copper nanoparticles appear red in color and are stable for weeks, ...

British Library Electronic Table of Contents (United Kingdom)

Nanoscale yttrium?barium?copper oxide (Y2BaCuO5, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3?8?nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influenc...

Energy Technology Data Exchange (ETDEWEB)

This paper described a newly developed chipper device for mounting on Claas Jaguar chipper harvesters for short rotation forestry harvesting. It was designed by the Agriculture Engineering Research Unit of the Agricultural Research Council in Rome, Italy. The new rotor has a lower number of blades compared to standard rotors and has a different cutting angle and drum insertion. This study evaluated the particle-size distribution of wood chips produced by standard rotors compared to those with the experimental rotor. The objective was to distinguish the particle size distribution of chips produced using the two types of chippers in order to evaluate the influence of wooden species in the chip formation process. Tests were conducted using 860 and 890 Claas Jaguar chipper harvesters, both equipped with standard and CRA-ING rotors. The experiment was conducted on poplar cultivations on biennial shift and on arboreal ...

Energy Technology Data Exchange (ETDEWEB)

This report made for the Swiss Federal Office of Energy (SFOE) discusses the conception, planning and construction of an easy-to-operate pilot heating plant that uses chicken litter as its fuel. The plant, which is installed at a chicken farm in Boesingen, Switzerland, produces 250 - 350 kW and not only supplies heat for two chicken sheds and two households, but also provides energy for a drying plant in summer. The results of measurements made on emissions are discussed and, within the framework of an eco-balance analysis, comparisons are made between the direct use of the droppings as manure or as a fuel. The cost-effectiveness of the plant is examined and the influence of plant size and other factors discussed. Further, legal questions concerning the use of chicken litter as a fuel for heating installations are discussed; the use of the droppings as a fuel is not foreseen in the legislation concerning water protection and airborne emissions of pollutants. ...

Energy Technology Data Exchange (ETDEWEB)

Swift heavy ion-solid interaction leads in volume to track creation and on the surface to the ejection of particles into the vacuum. To learn more about initial mechanisms of track formation, we are focused on the sputtering of uranium dioxide by fast heavy ions. This present study is exclusively devoted to the influence of the electronic stopping power on the emission of neutral particles and especially on their angular distribution. These measurements are completed by those of the ions emitted from UO{sub 2} targets bombarded with swift heavy ions. The whole experimental results give access to: i) the nature of the sputtered particles; ii) the charge state of the emitted particles; iii) the direction of ejection of the sputtered particles ; iv) the sputtering yields deduced from the angular distributions. These results are compared to the prediction of the ...

Science.gov (United States)

Pentaerythritol tetranitrate (PETN) is a relatively sensitive explosive used in many electroexplosive devices as well as in medicine. Of primary interest to LLNL is its use in items such as exploding bridgewire (EBW) detonators and exploding bridge foil initiators (EFI). In these devices the crystalline powder is pressed into a granular, low-density compact that can be initiated by an exploding wire or foil. The long-term stability of this pressed compact is of interest to weapon stockpile lifetime prediction studies. Key points about potential aging mechanisms can be summarized as follows: (1) There are a number of factors that can contribute to PETN instability. These include particle size, polymorphic phase transitions, crystal structure, impurities, moisture, occlusions, chemical incompatibility and biological (microorganism) action. of these factors the most important for long-term aging of high surface area powders used in detonators ...

International Nuclear Information System (INIS)

The interrelationship between the testing temperature and HfC strength increment of an arc-melted W-3.6Re-0.4HfC was determined from 1950 K to 2980 K in a vacuum of better than 1.3x10"-"5 Pa (10"-"7 torr). The present research was focused on the characteristic temperature at which the rapid coarsening of HfC particles occurred and the effect of the second-phase particle size on the high temperature strength properties of this material. It was found that the HfC particle strengthening was effective in a W-Re matrix up to a characteristic temperature of 2450 K in the short-term tensile test. Carbon was found to be the rate-limiting solute in the HfC particle growth. The strength of HfC strengthened alloy at temperature above 0.5 T_m is proportional to the square root of particle volume fraction. The yield strengths of W-3.6Re-0.26HfC calculated based on the ...

Science.gov (United States)

On the basis of the analysis of chemical components of the natural limestones from different deposits in China, the pore structures of the typical limestones, with the different CaCO3 content, were examined. The reactivity of the limestones was investigated by sulfuric acid titration and gas-liquid absorption methods. The research results showed that the specific surface area of the natural limestones studied in this work was about 1.8 m2/g. It was seen that the pH of the limestone slurry rapidly decreased and then back up when the sulfuric acid was added. The higher the CaCO3 content was, or the smaller the particle size was, the larger the pH back-up rate was, and similarly the faster the SO2 concentration of the reactor outlet increased. The Reactivity of the limestone obtained by the sulfuric acid titration had the same features as that obtained by the gas liquid absorption. Compared with the specific surface area, the CaCO3 content had ...

Science.gov (United States)

During this reporting period four direct coal liquefaction experiments have been completed and a fifth is underway. These experiments have produced conversion and selectivity data on samples of Utah coal slurried in tetralin and catalyzed using iron-titanium hydride. Hydrogen loading of the alloy, catalyst particle size, coal particle size, operating temperatures for alloy addition and liquefaction without the catalysts present, have all been studied during these four experiments. Conversions of 61% DAF in 30 min have been recorded at 485/sup 0/F and 520 psia. The fifth run using the same coal at a reduced particle size has begun, after which we will move to samples of Kentucky and Alabama coals. Equipment manufacture, delivery, and installation delays, totaling over 6 months, greatly reduced the time available for research, making a 6 month no cost extension ...

CERN Document Server

Particle Swarm Optimization

Energy Technology Data Exchange (ETDEWEB)

The distribution of graphite particles in graphite containing copper alloy was further improved very significantly using several procedures and technological modifications. The developed techniques attacked the graphite distribution problem in two ways. Realizing that clustering of very fine (5um) graphite particles is one of the two major problems, a pretreatment process has been developed using aluminum powders to deagglomerate graphite particles. Along with this, a two-stage stirring technique was used to first incorporate and then to distribute uniformly the deagglomerated particles in the melt. During this year, based on these developments, several components were cast to evaluate the castability of Cu alloy-graphite melts. In addition, machinability tests were done to clearly established that addition of graphite particles improve the machinability of copper MMC alloys over ...

Energy Technology Data Exchange (ETDEWEB)

Visualization of a liquid metal flow and image processing methods to measure the vector field are carried out by real-time neutron radiography. The JRR-3M real-time thermal neutron radiography facility in the Japan Atomic Energy Research Institute was used. Lead-bismuth eutectic was used as a working fluid. Particles made from a gold-cadmium intermetallic compound (AuCd{sub 3}) were used as the tracer for the visualization. The flow vector field was obtained by image processing methods. It was shown that the liquid metal flow vector field was obtainable by real-time neutron radiography when the attenuation of neutron rays due to the liquid metal was less than l/e and the particle size of the tracer was larger than one image element size digitized for the image processing. (orig.).

International Nuclear Information System (INIS)

The structure of nano-porous carbon, obtained by means of chlorination of carbide compounds with various crystal structure (SiC, TiC, Mo_2C) is studied through the method of small-angle diffraction. The angular dependences of the scattering intensity obtained are interpreted as the result of scattering from the nanoparticles of different size. The functions of the scattering particles distribution by the m(R_g) inertia radii are determined. It is shown that in spite of the source carbide, the highest fraction of the volume in the porous carbon constitute the particles with R_g #approx# 5 A. The nanoparticles in the samples obtained from SiC, wherein the average value of the R_g"a"v < 6 A, are most uniform by size. The nanoparticles in the porous carbon, obtained from Mo_2C, are on the average by two times larger

Energy Technology Data Exchange (ETDEWEB)

Sintered glass-ceramics have been produced using municipal incinerator solid residues and glass cullet or an inert waste, from feldspars processing, as sintering aids. The capability of three different mixtures, either previously vitrified or not, to be sintered was investigated by means of linear shrinkage, water absorption and bulk density measurements, and by X-ray diffraction analysis and scanning electron microscopy observations. Particular attention has been addressed to the study of particle size effect on the sintering process. The conclusions that can be drawn from the experimental study are that the preliminary vitrification step is essential in order to obtain a dense sintered glass-ceramic product in the 850-1050 C temperature range developing silicate crystalline phases. The optimal powder particle size that confers a good densification degree was found to be < 45 {mu}m. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The starting material for two certified and one candidate reference material was obtained from dried grass specially cultivated on a selected and well prepared soil. The Community Bureau of Reference (BCR) of the Commission of the European Communities produced two certified reference materials (CRM`s) from this dried grass: a rye grass material (CRM 281) certified in 1988 for the quality control of trace and toxic element analyses and a hay powder material (CRM 129) certified in 1989 for monitoring trace and minor elements. A fraction of the dried grass was used in 1993 for the preparation of a hay powder with a particle size of < 63 {mu}m using newly developed grinding techniques. This paper compares the production methods of these three materials and the obtained particle size distribution of the powders. The analytical evaluation of these production methods was carried out by solid sampling Zeeman ...

International Nuclear Information System (INIS)

The kinetics of the reactions between mixed powders of BaCO_3 and CuO, as well as BaCO_3 and Y_2O_3, have been studied using DXRD techniques as a function of particle size, temperature, and CO_2 pressure. Except for initial nucleation phenomena, the reaction rates are governed by shrinking core behavior for BaCO_3 particle sizes between 6 and 33 #mu#m. During the initial stages of the reactions, the surface reaction kinetics are governing, whereas the diffusion of CuO, Y_2O_3, and CO_2 are limiting factors at later stages in the reactions. Quantitative conversion data were used to determine the values of the activation energies and the pertinent diffusivities in these systems.

International Nuclear Information System (INIS)

Chemical and phase homogeneity of titanium-niobium sponge, produced by a combined magnesium-thermic reduction of niobium pentachloride and titanium tetrachloride mixtures, is investigated. It is ascertained that a sponge consists of spherical shape particles and has a large number of pores. Particle sizes are reduced with niobium being substituted for titanium from 50-500 #mu#m for titanium sponge to 1-40 #mu#m for niobium one, which testifies to the bormation in a titanium-niobium sponge of an alloy and not a mechanical mixture. A number of solid solutions is detected by X-ray phase analysis. Lattice parameters are determined.

Energy Technology Data Exchange (ETDEWEB)

In this study, liquid flame spray (LFS) was used to produce titania, silver and silver-titania deposits of nanoparticles. Titanium(IV)ethoxide (TEOT) and silver nitrate in ethanol solutions were used as precursors and sprayed into turbulent hydrogen-oxygen flame. Production rates of 1.5-40 mg/min of titania were used with silver additions of 1, 2, 4, and 8 wt% compared to titania. Nanoparticle deposits were collected by thermophoretic sampling at six different axial distances from the flame torch head: 3, 5, 10, 12, 15, and 20 cm, of which the all but the last one occurred inside the flame. The deposit samples were analysed by TEM and SAED analysis. The powder samples of the particles were also collected by electric precipitator to XPS and specific surface area analysis. Particle size and effective density after the flame in the aerosol were analysed with SMPS and ELPI. The results from the previous studies i.e. controlling ...

Energy Technology Data Exchange (ETDEWEB)

In this study, nanoparticle penetration was measured with a wide range of filter media using silver nanoparticles from 3 nm to 20 nm at three different face velocities in order to define nanoparticle filtration characteristics of commercial fibrous filter media. The silver particles were generated by heating a pure silver powder source via an electric furnace with a temperature of 870 deg. C, which was found to be the optimal temperature for generating an adequate amount of silver nanoparticles for the size range specified above. After size classification using a nano-DMA, the particle counts were measured by an Ultrafine Condensation Particle Counter (UCPC) both upstream and downstream of the test filter to determine the nanoparticle penetration for each specific particle size. Particle sampling time continued long ...

Energy Technology Data Exchange (ETDEWEB)

In this article, a method of producing elastic ferromagnetic composite containing particles of chemical pure iron with sizes of 0.10-0.15 mm was described. The particles were dispersed in an elastic matrix of an elastic silicone rubber. The filling factor of composite by ferromagnetic particles and porous factors were changed in the range from 0.15 to 0.45. The samples of the obtained composite were placed in the magnetic field with induction of 0-8 T, produced by the Bitter-type magnet. The longitudinal magnetostriction of samples was measured by using a coaxial capacitor with a movable plate. It was found that the maximal relative elongation of samples was 4.81% and hysteresis of magnetostriction and also remanent magnetostriction amounted to 1.08%. A slow decay of remanent magnetostriction up to 0.14% in 10{sup 5} s was also observed.

British Library Electronic Table of Contents (United Kingdom)

The characteristics of aerosol generation were studied experimentally in an ammonia-based wet flue gas desulfurization process. Particle size distributions and concentrations, morphologies and compositions before and after desulfurization were measured using an electrical low pressure impactor and scanning electron microscopy, respectively. The results show that aerosols can be generated between ammonia and sulfur dioxide resulting in gas-phase reaction and the aerosol concentration at the outlet of scrubber is significantly higher than at the inlet. Before desulfurization the particles are primarily silica-alumina minerals including O, Al, Si and C, while after ammonia-based desulfurization aerosol particles have smooth surfaces with regular structures, such as cubic and prismatic crystal...

Energy Technology Data Exchange (ETDEWEB)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 ..mu..m; drops of diameter size 1.5 ..mu..m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols from the washing water.

British Library Electronic Table of Contents (United Kingdom)

Catalyst deactivation during steam reforming of transportation fuels, primarily due to sulfur poisoning and carbon deposition, is a major hurdle in the commercialization of fuel cell technologies. In an attempt to better understand the phenomena, a previously formulated multi-component (Ni, Pd, Rh) catalyst supported on g-Al2O3 was studied under steam reforming of Jet A spiked with thiophene to achieve a total sulfur content of 1000ppm by weight. Analysis of fresh catalysts showed the presence of two groups of active metal particles, primarily distinguished by their size and composition; small particles (1-5nm) largely comprised of Rh and large particles (10-20nm) that were predominantly Ni, with or without the presence of Pd. Analysis of used catalysts showed sintering of crystallites con...

Energy Technology Data Exchange (ETDEWEB)

The Bureau of Mines has investigated the hazards of military explosives dispersed as dust clouds in a 20-L test chamber. For purposes of personnel safety, the spark ignitability of the explosives in the form of unconfined dust layers was also studied. The 20-L data show that most of the explosives dusts were capable of sustaining explosions as dust clouds dispersed in air and some dusts were even capable of sustaining explosions when dispersed in nitrogen. The finest sizes of explosives dusts were less reactive than the larger sizes; this is opposite to the particle size effect observed previously for the pure fuel dusts. The data for the explosives dusts were compared to those for pure fuel dusts. 27 refs., 47 figs.

Energy Technology Data Exchange (ETDEWEB)

Essential to today's modern refineries and the gasoline production process are fluidized catalytic cracking units. By using a computational fluid dynamics (CFD) code developed at Argonne National Laboratory to simulate the riser, parametric and sensitivity studies were performed to determine the effect of catalyst inlet conditions on the riser hydrodynamics and on the product yields. Simulations were created on the basis of a general riser configuration and operating conditions. The results of this work are indications of riser operating conditions that will maximize specific product yields. The CFD code is a three-dimensional, multiphase, turbulent, reacting flow code with phenomenological models for particle-solid interactions, droplet evaporation, and chemical kinetics. The code has been validated against pressure, particle loading, and product yield measurements. After validation of the code, parametric studies were performed on ...

International Nuclear Information System (INIS)

The opportunity of exposure to high-energy radiation up to GeV is increasing as in civilian aircrafts and at particle accelerators. The transport of such energetic particle is still difficult to describe precisely and thus verification by measurement using a well characterized instrument is indispensable for reliable dosimetry. However, no reference calibration field has been established for the high-energy range. We thus propose to use a facility at the summit of Mt. Fuji (3776 m in altitude; N35.36o, E138.73o), the highest place in Japan, for characterization of radiation instruments that are possibly used in high-energy radiation fields. For demonstration of the effectiveness, two moderator-type neutron monitors (NCN1 and WENDI-II) having different energy response functions were employed for cosmic-ray neutron measurements in the summer of 2009. In comparison with numerically simulated values, it was found that the ...

British Library Electronic Table of Contents (United Kingdom)

We provide an efficient computational approach to solve the mixed integer programming (MIP) model developed by Tarim and Kingsman [8] for solving a stochastic lot-sizing problem with service level constraints under the static-dynamic uncertainty strategy. The effectiveness of the proposed method hinges on three novelties: (i) the proposed relaxation is computationally efficient and provides an optimal solution most of the time, (ii) if the relaxation produces an infeasible solution, then this solution yields a tight lower bound for the optimal cost, and (iii) it can be modified easily to obtain a feasible solution, which yields an upper bound. In case of infeasibility, the relaxation approach is implemented at each node of the search tree in a branch-and-bound procedure to efficiently sear...

International Nuclear Information System (INIS)

The 1.04 GeV-proton elastic scattering from "4"0Ca is studied in the framework of the coherent density fluctuation model (CDFM). The calculations are carried out in the Glauber theoretical scheme with three different charge densities. It is shown that: i) the account of the flucton correlations leads to results considerably different from those obtained in the independent particle Glauber approach (IPGA); ii) in contrast to the case of IPGA the use of a more realistic density improves the agreement of CDPM-results with the experimental data. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The geodesic equation for space-like objects moving along a circular trajectory in the expanding universe is considered. Our analysis leads to the conclusion that ancient cosmological tachyons may exist in the present-day world and may play an important role in (i) the internal structure of hadrons conceived as nonlocal objects called strings, (ii) the T-symmetry violation observed in the weak K-decays, (iii) the multidimensional unified field theories of Kaluza-Klein type, and in (iv) the classical models of charged particles which combine ordinary electromagnetism with a self-interacting version of Newtonian gravity. 18 refs.

Energy Technology Data Exchange (ETDEWEB)

SC-CO/sub 2/ extraction of oil from peanuts is an alternative to hexane extraction or the mechanical oil press. Oil was successfully extracted using SC-CO/sub 2/ at temperatures of 25-120/sup 0/C and pressures of 140 -690 Bar. Pressure, temperature and particle size affected the extraction of oil. In the range studied, the highest values of temperature and pressure gave highest solubilities.

International Nuclear Information System (INIS)

Technology of plasma sputtering, structure and properties of zirconium dioxide coatings were studied. Necessity of void number increase to enhance coating heat-resistance is shown. Optimal powder particle size (20-60 #mu#m) providing optimal coating porosity was determined. Weight part of stabilizating oxide (Y_2O_3) in ZrO_2 for formation in coating of microcracks serving as barriers for macro-cracks propagation was determined.

UK PubMed Central (United Kingdom)

In normal subjects, apolipoprotein E (apo E) is present on very low density lipoproteins (VLDL) (fraction I) and on particles of a size intermediate between VLDL and low density lipoproteins (LDL) (fraction...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Using an experimental pilot plant, designed and built for the tests, the influence of the following parameters was determined: desulphurization of the test gas, temperature, residence time in the reactor tube, concentration of the hydrogen sulphide and desulphurization agent, size of the particles which comprise the agent and composition of the gas. Allowance was made for the effect of calcination and carbonisation. Desulphurization was carried out with limestone on a gaseous mixture of CO and H/sub 2/. A mathematical description of the test findings and yield is presented. 8 refs.

Energy Technology Data Exchange (ETDEWEB)

The oxide colloidal route, developed in the laboratory for mono-metallic catalysts, consists in preparing a metallic oxide hydro-sol which leads to the supported catalyst after deposition onto a support and an activation stage. In this work, this method has been adapted to the preparation of alumina supported bimetallic Pd-Sn catalysts to determine its interest for the control of the properties of the bimetallic phase (size, composition and structure). In the preliminary study concerning tin oxide sols, SnO{sub 2} (size=2,3 nm) and Sn{sub 6}O{sub 4}(OH){sub 4} (size = 25 nm) nano-particles were synthesized by neutralization respectively for tin(IV) and tin(H). The control through the pH of the aggregation of the PdO and SnO{sub 2} particles revealed that increasing oxide solubility promotes integral re-dispersion of the oxide particles. To synthesize oxide ...

Science.gov (United States)

A method is disclosed of producing blast furnace coke by (1) compacting a finely divided coal wherein at least about 60% by weight of the coal has a diameter of less than about 1/8 inch to form a coal compact, which compact immediately after removal from the compacting means comprises at least about 20% by weight of particles having a particle size of less than 1/4 inch in diameter; (2) breaking the thus formed compact such that the bulk density is sufficiently increased to be capable of conversion into coke suitable for use in large blast furnaces upon carbonization thereof; and (3) carbonizing the broken compact to thereby produce blast furnace coke having a minimum hardness of about 68 and a minimum stability of about 55. The compacting is preferably performed at a pressure equivalent to that achieved by passing the finely divided coal between rolls at a pressure applied to the coal of between about 20 and about 60 ...

Science.gov (United States)

Macromolecular and polyanionic Na(+)-poly(gamma-glutamic acid) (PGA) silver nitrate complex acted as both a metal ion provider and a particle protector to fabricate nanosized silver colloids under chemical reduction by dextrose. The formation and size of particles have been characterized from transmission electron microscopy (TEM), dynamic light scattering analysis and UV-vis spectrophotometer. The results showed that the average particle size was 17.2+/-3.4 to 37.3+/-5.5 nm, apparently depending on the complex concentration. It was found that the rate constant and conversion of silver nanoparticles were proportional to the concentration of PGA. The growth mechanism of nanosized silver colloid was fully discussed. In addition, the in vitro cytotoxicity evaluated by L929 fibroblasts proliferation and antibacterial activity against Gram-positive strain (methicillin-resistant S. aureus ...

Science.gov (United States)

The method of producing blast furnace coke by (1) compacting a finely divided coal wherein at least about 60% by weight of the coal has a diameter of less than about 1/8 inch to form a coal compact, which compact immediately after removal from the compacting means comprises at least about 20% by weight of particles having a particle size of less than 1/4 inch in diameter; (2) breaking the thus formed compact such that the bulk density is sufficiently increased to be capable of conversion into coke suitable for use in large blast furnaces upon carbonization thereof; and (3) carbonizing the broken compact to thereby produce blast furnace coke having a minimum hardness of about 68 and a minimum stability of about 55. The compacting is preferably performed at a pressure equivalent to that achieved by passing the finely divided coal between rolls at a pressure applied to the coal of between about 20 and about 60 tons per ...

Energy Technology Data Exchange (ETDEWEB)

Niobium carbide can be used to inhibit WC grain growth in hardmetal. The performance of a NbC powder produced at low temperature by solid-gas reaction (an experimental powder) as WC grain growth inhibitor is compared with that of a commercial NbC powder. It is verified that NbC effectively inhibits heterogeneous WC coarsening. This results in an increase in hardness. The commercial and experimental NbC powders exhibit a comparable performance in inhibiting the WC grain coarsening, in spite of a significant difference in particle size and shape. The commercial NbC powder is very fine while the experimental one is coarse and porous, but its crystallites are finer than those of the commercial product. The milling procedure used to prepare the alloys is able to reduce the particle size of the experimental NbC, and thus guarantee a dispersion of the particles with a quality level ...

Energy Technology Data Exchange (ETDEWEB)

Micron-size Ni-base alloy (NBA) powders were mixed with both 1.5 wt.% (hereinafter %) micron-size CeO{sub 2} (m-CeO{sub 2}) and also 1.5% and 3.0% nano-size CeO{sub 2} (n- CeO{sub 2}) powders. These mixtures were coated on low-carbon steel (Q235) by 2.0 kW CO{sub 2} laser cladding. The effects on the microstructures, phases and electrochemical corrosion of the coatings upon the addition of m- and n- CeO{sub 2} powders to NBA (m- and n- CeO{sub 2} /NBA) have been investigated. The results showed that a smooth coating was prepared under suitable processing parameters (P= 2.0 kW, V= 180 mm min{sup -1}) by adding 1.5% n- CeO{sub 2}. In addition to the primary phases of {gamma}-Ni, Cr{sub 23} C{sub 6} and Ni{sub 3} B in the Ni-base alloy coating, CeNi{sub 3} was formed in Ni-base alloy coatings with both n- CeO{sub 2} and m-CeO{sub 2} particles, and CeNi{sub 5} appeared in the coating upon decreasing the ...

Energy Technology Data Exchange (ETDEWEB)

The measurement methods of homogeneity of dispersion fuel were analyzed. The effects of mixing method, rotating speed, particle shape, particle size and moisture content on homogeneity of U{sub 3}Si/Al powder mixture were characterized by the apparent density measurement. The effects of fuel particle shape on green properties and optimum compaction conditions were investigated in U{sub 3}Si{sub 2}/Al powder compacts. 3 kinds of measurement method on the homogeneity were analyzed by apparent density measurement method, x-ray image contrast method and image analysis method of mixed powders or fuel rods. The homogeneity of dispersed fuel powder mixture was analyzed using three kinds of mixing, by apparent density measurements method. The homogeneity of powder mixture increased with rotating speed of the V-shape tumbler mixer. The comminuted irregular shaped particles and smaller ...

CERN Document Server

Protoplanetary disks start their lives with a dust free inner region where the temperatures are higher than the sublimation temperature of solids. As the star illuminates the innermost particles, which are immersed in gas at the sublimation edge, these particles are subject to a photophoretic force. We examine the motion of dust particles at the inner edge of protoplanetary disks due to photophoretic drag. We find that, in a laminar disk, photophoretic drag increases the size of the inner hole after accretion onto the central body has become subdued. This region within the hole becomes an optically transparent zone containing gas and large dusty particles (>>10 cm), but devoid of, or strongly depleted in, smaller dust aggregates. Photophoresis can clear the inner disk of dust out to 10 AU in less than 1 Myr. At late times, the edge reaches a stable equilibrium between inward ...

Energy Technology Data Exchange (ETDEWEB)

Two computational problems were worked on for this study. The first chapter examines the option of coal combustion using oxygen feed with carbon dioxide recycle to control the adiabatic flame temperature. Computer simulations using an existing state-of-the-art 3-dimensional computer code for turbulent reacting flows with reacting particles were employed to study the effects of increased carbon dioxide mole fraction on the char burnout, radiant heat transfer, metal partitioning, and NOx formation. The second chapter compares assumptions for the CO/CO{sub 2} ratio at the surface of mineral inclusions made in previous studies to predictions obtained from a pseudo-steady state kinetic model (SKIPPY) for a single porous particle. The detailed kinetic simulations from SKIPPY for varying particle sizes and bulk gas compositions were used to develop algebraic expressions for the CO/CO{sub 2} ratio that can be ...

Energy Technology Data Exchange (ETDEWEB)

For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size ...

International Nuclear Information System (INIS)

DF (decontamination factor) of two types of air filter was investigated against "1"9"8Au aerosol particles with AMAD (activity median aerodynamic diameter) = 1.2 #mu#m and #sigma#g (geometric standard deviation) = 2.0. One of the filters, SO filter, is HEPA (high efficiency particulate air) filter media with 46 mm#phi#, and the other is HE-40T (cellulose-glass fiber filter for dust sampling) filter media with 40 mm#phi#. DF of the SO filter was found to be over 5 x 10"4 at air flow rate of 1 l/min. And DF of HE-40 T filter was determined to be 94#+-#4 at the same airflow rate. In the multistage HE-40 T filter system, DF decreased at each succeeding stage. It was confirmed by numerical simulation that the decrease of DF was not inconsistent with the decrease of collection performance in each successive filter. It was also confirmed that DF could be predicted by the numerical simulaiton, if particle penetration function of filter and ...

International Nuclear Information System (INIS)

Molybdenum oxide nanostructures were synthesized utilizing the solution combustion method where the ammonium molybdate powder and an organic additive were used as precursors. Different organic additives including ethylene diamine tetra-acetic acid (EDTA), polyethylene glycol 200 (PEG 200), sorbitol and urea were used as surfactants in order to investigate the effect of additive structure on morphology and particle size of products. Also various reaction parameters such as the additive/Mo molar ratio, concentration of metal ion in solution, pH of the reaction, and temperature of the synthesis media were changed to study effects on product morphology and size. Outcomes were characterized by Scanning Electron Microscopy (SEM), X-ray diffraction, and Transmission Electron Microscopy (TEM) techniques. Results show a variety of MoO_3 nanoparticles and nanorods produced within the size range of 10-80 nm. ...

Energy Technology Data Exchange (ETDEWEB)

Size-selected SnO{sub 1.8}:Ag mixed nanoparticle films have been prepared using a gas phase condensation method. Transmission electron microscopy showed that the applied size-selection technique yields well-defined, monodisperse and spherical SnO{sub 1.8} and Ag nanoparticles, both with a fixed diameter of 20 nm. The technique allows an independent variation of the particle size of both materials as well as the concentration of Ag. It allows to assess the influence of these parameters on the gas-sensing properties of the films, here for ethanol vapor in synthetic air. SnO{sub 1.8}:Ag nanoparticle films show optimal values of the sensor signal and response time at a Ag nanoparticle concentration of 5%. Due to the fact that the Ag nanoparticles are clearly distinct from the SnO{sub 1.8} nanoparticles in the film, the most probable mechanism leading to improved sensor properties is chemical sensitization ...

Energy Technology Data Exchange (ETDEWEB)

Individual nanoscale building blocks exhibit a wide range of size-dependent properties, since their size can be tuned over known characteristic length scales of bulk materials. In the last several years, the possibility of combining different materials in the form of two and three component nanoparticles (NPs) has been extensively explored. Also multi-component materials can be obtained via self-assembly of NPs from their binary colloidal mixtures. These new nanocrystal solids may possess tunable collective properties that originate from interactions between size and composition controlled building blocks. Exchange coupling between neighboring NPs of magnetically soft and hard materials enhances the magnetic energy product of the nanocomposite material. Randomly mixed solids of small and large semiconducting CdSe NPs revealed enhancement of photoluminescence intensity of large semiconductor particles ...

Science.gov (United States)

1. Contest rules The European Space Agency (ESA) is launching a public competition to find the most suitable names for its four Cluster II space weather satellites. The quartet, which are currently known as flight models 5, 6, 7 and 8, are scheduled for launch from Baikonur Space Centre in Kazakhstan in June and July 2000. Professor Roger Bonnet, ESA Director of Science Programme, announced the competition for the first time to the European Delegations on the occasion of the Science Programme Committee (SPC) meeting held in Paris on 21-22 February 2000. The competition is open to people of all the ESA member states (*). Each entry should include a set of FOUR names (places, people, or things from history, mythology, or fiction, but NOT living persons). Contestants should also describe in a few sentences why their chosen names would be appropriate for the four Cluster II satellites. The winners will be those which are considered most suitable ...

Science.gov (United States)

Large amounts of atmospheric dust are lifted from the North African deserts and are transported by the trade winds over the Caribbean region, especially during the summer months. How African dust particles influence the earth's radiative budget is not well understood because these particles are highly variable and their physical, optical, and chemical properties are poorly characterized, especially when they are atmospherically processed as are those that travel from Africa to the Caribbean region. Here we present results of aerosol measurements performed at Cape San Juan (CPR), a ground-based station located at the northeastern tip of the Caribbean island of Puerto Rico. We used a condensation particle counter to determine the particle number concentration, a sunphotometer (part of the AErosol RObotical NETwork, AERONET, aeronet.gsfc.nasa.gov) to determine volume size ...

Energy Technology Data Exchange (ETDEWEB)

A mesoscopically ordered lamellar gel phase of a polymer-grafted, lipid-based complex fluid is used as a scaffolding to spatially organize inorganic nanoparticles. The complex fluid provides both a highly anisotropic environment and a segregated aqueous and organic domains in which inorganic nanoparticles can be selectively placed by tailoring their size and surface characteristics. Three types of silver nanoparticles -- underivatized, surfactant-stabilized, and dodecanthiol-derivatized -- were evaluated. Comparison of the surface plasmon resonance of the various silver particles dispersed in conventional solvents to those contained within the complex fluid was used to determine the region of spatial localization in the lamellar gel phase. Silver particles rendered hydrophobic by capping with an alkane thiol insert into the hydrocarbon bilayer region. Surfactant-stabilized and underivatized silver nanoparticles reside in ...

International Nuclear Information System (INIS)

The distribution of radiation dose commitments within the body that can result from the lung deposition of a number of transuranic radionuclides ("2"3"7Pu, "2"3"8Pu, "2"3"9Pu, "2"4"0Pu, "2"4"1Pu, "2"4"2Pu, "2"4"3Pu, "2"4"4Pu, "2"4"1Am, "2"4"2Am, "2"4"3Am, "2"4"4Am, "2"4"2Cm, "2"4"3Cm, "2"4"4Cm, and "2"4"6Cm) was calculated. The variables that influence these organ dose commitments include the mobility of the particle or its dissolution products within the body, the radiation characteristics of the inhaled radionuclides and their progeny, and the size of the particles inhaled. In the calculation of organ dose commitments for whole-body, lungs, liver, bone tissues, kidneys, and gastrointestinal tract from the inhalation of transuranium radionuclides, physical characteristics of importance are the dimensions of the particle, its aerodynamic properties, and its density. For particles ...

Energy Technology Data Exchange (ETDEWEB)

Reduction of silver myristate (AgMy) under mild thermal reaction conditions in a dipolar aprotic solvent i.e. N, N-dimethylformamide (DMF) has been carried out. UV-visible absorption measurements of dried and re-dispersible brown flocculants showed broad features of surface plasmon resonance (SPR) due to silver nanoparticles. The freshly isolated particles showed absorption bands at 414 and 485 nm, respectively, due to inter-particle coupling or clustering of silver ions and silver atoms. X-ray diffraction (XRD) pattern of fcc zero-valent silver resulted in crystallite size of about 10 nm. Scanning electron microscopy (SEM) revealed formation of rod shaped silver with increasing reaction temperature. Thermal analysis (TGA) showed about 10% weight loss due to organic capping.

British Library Electronic Table of Contents (United Kingdom)

Silica-reinforced natural rubber (NR) composite was prepared by using tetraethoxysilane (TEOS) as a precursor to generate silica particles inside the rubber. The silica was generated in situ by the sol-gel process of TEOS that was mixed directly into commercial-graded NR latex having 60% dry rubber content and 0.7% ammonia. The conversions of TEOS to silica inside the rubber were ranging from 90 to 97%. The silica particles dispersed evenly without extensive aggregation with sizes between 100 and 500 nm, as determined by scanning electron microscopy (SEM). An experimental design methodology, namely "two-level factorial design," was used to evaluate the influence of the amounts of TEOS, ammonia, and gelation time on the tensile modulus, tensile strength, and tear strength of the vulcanizate...

Energy Technology Data Exchange (ETDEWEB)

It was developed a new formulation of macro aggregates of Samarium 153 ({sup 153} Sm-MH) for the arthropaties treatment. The radio pharmaceutic was prepared by reaction of Samarium 153 chloride (SmCl{sub 3}) in aqueous environment with sodium boron hydride in NaOH 0.5 N. The microscopic analysis shown that the particles have an average size of 4% m (range 1-14 {mu} m). The velocity of sedimentation was 0.008 cm/min with high stability in vitro in human serum. The biological studies in healthy rabbits, shown that the complex is retained inside the articulation still eight days after of the administration of the radiopharmaceutical. Likewise, it is presented the data of absorbed dose in the different target organs, which was determined by thermoluminescent dosimetry (TLD) through the use of a REMCAL phantom (radiation equivalent manikin calibration). (Author)

International Nuclear Information System (INIS)

The present work is a research of the effect of helium on the microstructure, mechanical properties and fracture behaviors of a type 316 austenitic steel. Helium implantation was performed by 30-MeV #alpha#-particle injection on very small size specimens, using a cyclotron. Average helium content in a He-deposited region was up to 2000 appm He. In the case of 2000appm He implantation, intergranular fracture was sometimes observed on the helium deposited region after tensile test at room temperature. At elevated temperature test, however, this material showed the transition of fracture mode from transgranular-ductile fracture at 773K to intergranular fracture at 873. In the case of 500 appm He implantation, the transition of fracture mode was recognized at a temperature range of 873K to 973K. (author).

International Nuclear Information System (INIS)

Evaporation of "9"9"mTc-pertechnetate at about 2500"0C on a carbon surface generates an ultrafine aerosol of labelled carbon clusters. Its particle size of about 2-5 nm enables the aerosol to behave similarly to a gas regarding the ability of penetration. After inhalation, the radioactive particles adhere to the walls of the respiratory bronchioli and alveoli. The high concentration of the radioactivity in the argon carrier gas makes it possible to record a scintigram after a single deep breath. We studied four healthy volunteers and 79 patients including 34 with a tentative diagnosis of pulmonary embolism, 20 with bronchus carcinoma, and 15 with various other lung diseases. Ten of these patients were infants, the youngest being nine months old. All patients also had a perfusion scintigraphy. (orig.).

Energy Technology Data Exchange (ETDEWEB)

A new class of low aspect ratio toroidal hybrid stellarators is found using more general plasma confinement optimization criterion than quasi-symmetrization. The plasma current profile and shape of the outer magnetic flux surface are used as control variables to achieve near constancy of the longitudinal invariant J* on internal flux surfaces (quasi-omnigeneity), in addition to a number of other desirable physics target properties. We find that a range of compact (small aspect ratio A), high {beta} (ratio of thermal energy to magnetic field energy), low plasma current devices exist which have significantly improved confinement both for thermal as well as energetic (collisionless) particle components. With reasonable increases in magnetic field and geometric size, such devices can also be scaled to confine 3.5 MeV alpha particle orbits.

British Library Electronic Table of Contents (United Kingdom)

Runit Island on Enewetak Atoll was very heavily impacted by the U.S. nuclear testing campaign in the northern Marshall Islands (1946?58). The primary source of contamination on Runit Island was the 1958 Quince safety test where a large quantity of device plutonium (Pu) was scattered over the area near the GZ. A second low-yield device was detonated on the same site 10?days later, further disturbing the soil and leaving behind a very heterogeneous pattern of contamination including milligram-size particles of plutonium. A limited cleanup of the Fig-Quince zone was carried out in 1979. During this period, the effectiveness of the cleanup operations was primarily evaluated on the basis of bulk soil concentration data with little consideration given to the heterogeneity and long-term material-...

International Nuclear Information System (INIS)

Ionizing radiations that differ in number, size, and distribution of energy deposition events might be expected to cause different effects for the same absorbed dose. Furthermore, microdosimetry calculations suggest that large variations in biological effectiveness might be expected for internally deposited alpha-emitting radionuclides for the same absorbed dose, depending upon the specific activity and spatial distribution of the sources in tissue. The study described in this article was designed to demonstrate these phenomena in vitro. Cultured Chinese hamster ovary (CHO-K1 BH4) cells were exposed in vitro to inert, insoluble ceramic microspheres in zirconium dioxide labeled with "2"3"9Pu. The average exit energy of the 5.15 MeV alpha particle was calculated to be 4.3 MeV. Exposure times varied from four to seven hours to achieve the desired dose level.

CERN Document Server

X11 Desktop Environments (KDE and GNOME) - Part II

British Library Electronic Table of Contents (United Kingdom)

In the paper, the effect of Ni content, WC grain size and Mo2C addition on WC-6.25wt%TiC-9.3wt%Ni cemented carbide were investigated to improve the properties of Ni-bonded cemented carbides. The results show that the decrease of Ni content will result in the decrease of transverse rupture strength and increase of hardness; with the decrease of WC particle size, hardness increases due to the refinement of WC grains, however, the transverse rupture strength decrease due to the decrease of Ni binder thickness; Mo2C proves to be an effective grain growth inhibitor. With the increase of Mo2C content, the WC grains are refined and the hardness and transverse rupture strength are improved. Generally, when the Ni content is decreased to 8.4wt%, 13.45mm WC is used and 1.2wt% Mo2C is added, a higher...

Energy Technology Data Exchange (ETDEWEB)

Slurry characteristics have a significant impact on centrifugal pump performance. For instance, as particle size increases or the percent solids concentration increases, pump head and efficiency decrease. Therefore, before a slurry pump is selected, it is important to define the slurry characteristics as accurately as possible. The effect of the slurry characteristics on the head and efficiency of the centrifugal pump will be emphasized (the effect on flowrate is less significant). The effect of slurry characteristics is more predominant in smaller pumps (with smaller diameter impellers) than in larger pumps. The data and relationship between the various slurry parameters have been developed from correlations and nomographs published by pump vendors from their field data and test results. The information helps to avoid specifying an undersized pump/motor assembly for slurry service.

British Library Electronic Table of Contents (United Kingdom)

The objective of materials research is the development of economical, safe and efficient synthesis routes that lead to the formation of a photocatalyst which is able to overcome performance problems related to particle size, crystallinity, or low surface area. Here, we report high-quality functional nanoparticles of calcium bismuth mixed oxide with 15nm nominal size corresponding to a specific surface area of 41m^2/g which were produced by single-step flame spray synthesis (FSS). The high temperature of the flame afforded creation of oxygen vacancies which were quantified by near edge X-ray absorption fine structure (NEXAFS) spectra. These two parameters, developed active surface area and created in the flame oxygen vacancies, allowed to enhance the photocatalytic activity of calcium bismu...

International Nuclear Information System (INIS)

The examination of the high-temperature properties of the alloy Alloy 800HT has shown that both the creep performance and the microstructure of the material can be purposefully set by the initial heat treatment. At the high temperatures applied, (700-900 C), a rapid softening process sets in induced by carbide precipitation, stabilization, and coarsening. This softening process causes creep velocities strongly accelerating as a function of duration of the heat treatment prior to the creep test. The identified cause of the softening effect is a change in particle size that could be verified by SEM and TEM. It is shown that two different carbide precipitate size classes are responsible for the softening effect. While the precipitates dectable by TEM become effective primarily via interactions with dislocations, the carbide precipitates detectable only by SEM contribute to a hardening of the grain boundaries and the ...

CERN Document Server

Particle Detection with drift Chambers

Energy Technology Data Exchange (ETDEWEB)

Heat transfer processes use fluids which are generally not pure and can react with transfer surfaces. These surfaces are subject to deposits which can be sediments harmful to heat transfer and to integrity of materials. For nuclear plant steam generators, sludge build-up accelerates secondary side corrosion by concentrating chemical species. A major safety problem involved with such a corrosion is the growing of circumferential cracks which are very difficult to detect and size with eddy current probes. With a view to understand and control this problem, it is necessary to develop a mathematical model for the prediction of sludge behavior in PWR steam generators. Based on fundamental principles, this work intends to use different models available in literature for the prediction of the phenomenon leading to the accumulation of sludge particles at the bottom (the tubesheet) of a PWR. For that, a three-dimensional simulation of magnetite ...

International Nuclear Information System (INIS)

A few metal complexes of isatin-isonicotinoylhydrazone with Ni(II), Cr(III), Co(II), Cu(II), Zn(II) and Cd(II) have been prepared and characterized on the basis of elemental analyses, infrared and electronic spectra as well as "1H NMR spectra, conductivity and magnetic measurements. In view of the results obtained, it has been found that two molecules of isatin-isonicotinoylhydrazone are chelated to the central metal ion as bis-uninegative ONO tridentate ligand forming non-electrolytic octahedral metal complexes. (author)

British Library Electronic Table of Contents (United Kingdom)

Ultra fine tungsten carbide and cobalt powders were milled by high energy planetary ball mill at different ball to powder weight ratios (BPR) to produce particles of WC-10wt%Co hard metal in nanometer scale size. Microstructural characterizations by TEM show that the particle size of tungsten carbide was achieved to 32nm after milling at 15 BPR during 10h. In order to reduce the WC grain growth during the sintering process, tantalum carbide was added to the hard metal as a WC grain growth inhibitor. The nano hard metal powders were compacted at 200MPa pressure and sintered at 1370-1450degreeC temperatures in a high purity hydrogen atmosphere. The results show that the addition of 0.6wt% of TaC improves the hardness and fracture toughness from 1493 HV30 and 11.8MPam (for TaC free sample) to...

Energy Technology Data Exchange (ETDEWEB)

Two major modes of CO adsorption on SiO{sub 2}-supported Pd reflect different extents of back-donation, which is, at least in part, controlled by the local electron density at the adsorption site. The fraction of CO in the bridging mode (B) increases and that of the linear mode (L) decreases, with increasing size of the Pd particles, indicating high electron density at Pd atoms in terraces of close-packed crystal faces, in agreement with Smoluchowski's classical model. For samples reduced at 300{degree}C our data points and those of other authors are located on a common curve of B/L vs metal dispersion. Extensive reduction at 600{degree}C results in significantly lower B/L values, attributed to the incipient formation of a palladium silicide. Oxidation followed by reduction at 300{degree}C destroys the silicide, and the B/L value returns to the original curve.

International Nuclear Information System (INIS)

Full text: The production of #beta#-sialon from kaolinite and carbon has been studied using Hulu Langat Kaolin and activated carbon as raw materials. The sintered temperature is shown to play a prominent role in the process of sialon conversion. Apart from temperature, nitrogen flow rate is also affect the production of #beta#--sialon. This study was carried out on the effect of additive, Y_2O_3 and Al_2O_3 at different temperature that will be mixed and sintered. The additives are expected to affect the formation of #beta#--sialon and Y-sialon upon the synthesis. The mineral and phase development was analysed using X-Ray Diffraction technique (Rigaku Geigerflex) while its chemical compositions through X-Ray Fluorescent Spectrophotometer (Shimadzu XRF 1700) and the particle size distribution analysis through Particle Size Analyser (Horiba, CAPA 700). The observed changes in the microstructure were ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 deg. C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed ...

Energy Technology Data Exchange (ETDEWEB)

The low-cycle fatigue properties of the ferritic-martensitic steels MANET I and II and F82H-mod, have been investigated at a temperature of 200 C. The strain-controlled fatigue has been performed with strain ranges between 0,4% and 1,0% and at a strain rate of 8.10{sup -4} s{sup -1}. The steel F82H-mod, is characterised by a higher plastic strain amplitude compared to MANET I and II. Some of the specimens have beenirradiated with a 104 MeV {alpha}-particle beam. The homogeneous implantation of 400 appm He leads to a hardening of the material. At the beginning of the fatigue tests the stress response of the irradiatedspecimens is higher compared to the unirradiated specimens. In general, thematerial shows softening during fatigue. The softening of irradiated material, which is fatigue tested with a high total strain amplitude, is higher than that of the unirradiated material. The lifetime is reduced. For irradiated specimens ...

International Nuclear Information System (INIS)

In laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS), the properties of laser-generated aerosols, such as size and composition, are crucial for matrix-independent quantification. In this study, the aerosol particle morphology and elemental composition generated by two state-of-the-art laser systems (ArF excimer nanosecond-UV laser and Ti:sapphire femtosecond-IR laser) were investigated by electron microscopic techniques. Electrostatic sampling of the aerosols directly onto transmission electron microscopy (TEM) grids allowed us to study the morphology and elemental composition of the aerosols using TEM and TEM-EDX (energy dispersive X-ray spectroscopy) analyses, respectively. The results of the electron microscopic studies were finally compared to the LA-ICPMS signals of the main matrix components. The investigations were carried out for non-conducting materials (glass and zircon), metallic samples (steel and brass) and ...

International Nuclear Information System (INIS)

X-ray fluorescence analysis was used to determine the zinc content of the ''Perilacin'' powder and the ZnO content of the ''Epiderman-pix'' powder. The characteristic Ksub(#alpha#) line of zinc was excited using a "1"4"7Pm/Mo source (10"7 s"-"1) and the molybdenum Ksub(#alpha#) line (17.47 keV). 4 to 5% Zn and 45 to 49% ZnO were determined with a NaI(Tl) scintillation detector. The radiation intensity was found to decrease with particle size. (M.K.).

British Library Electronic Table of Contents (United Kingdom)

Miscanthus is a potential feedstock for the production of biofuels. Lignocellulosic biomass is not soluble in conventional solvents, but Miscanthus and other lignocellulosic biomass have reasonable solubilities in some ionic liquids. The solubility of Miscanthus in a variety of hydrophilic ionic liquids was measured as a function of particle size, temperature and time for dissolution. In addition to temperature and time, the ionic liquid anion has a significant effect on solubility and rate of dissolution. The moisture content of Miscanthus lowers its solubility in certain ionic liquids. Chloride, acetate, and phosphate-based ionic liquids favor solubility. A tentative correlation for the solubility of Miscanthus is proposed in terms of Abraham solvation parameters obtained from quantum-ch...

Energy Technology Data Exchange (ETDEWEB)

Calcium sulfate dihydrate in large crystal form is produced by maintaining the circulation of the lime containing scrubbing solution in the desulfurization scrubbing of flue gases from a power plant boiler so that it has a residence time of 5 to 25 hours, preferably 15 hours. The crystals are moved by passing a portion of the recirculation through a thinner in which a sludge containing crystals with a mean particle size of which 90% is in excess of 100 microns is removed. This product can be dewatered and treated with sulfuric acid and steam to convert it to the alpha semihydrate and is free from sulfite.

International Nuclear Information System (INIS)

A complete electron paramagnetic resonance power pattern characterization of Fe"3"+ in cubic sites in presented. A one-to-one correspondence among the peaks appearing in the powder pattern and the outer fine-structure transitions (Mnot = 1/2 ) observed in the single crystal along the , , and directions is shown. It is shown that the process of mechanically grinding the single crystal to a powder (particle size approx.1--10 #mu#) does not remove the cubic symmetry sites. No axial or lower symmetry sites which may be induced by lattice distortion of the crystallites due to strain have been observed.

Energy Technology Data Exchange (ETDEWEB)

The efficiency of NbC on WC grain coarsening in a WC-10wt.%Co hardmetal alloy was demonstrated by hardness measurement and WC granulation observation. The heterogeneous and overall grain growth were controlled. A low temperature experimentally produced NbC was used and compared to the inhibition potential of a commercial NbC powder. The results were the same in terms of structural fineness and hardness. The dispersion of the experimental NbC was not a problem, in spite of its size. The experimental NbC has very large particles, formed by agglomerates of small crystallites. During milling these agglomerates could be broken down. (orig.)

Science.gov (United States)

Cosmological N-body and hydrodynamic simulations start with a realization of a random density fluctuation field representing a cosmological model at an early epoch. The density field is often replaced by a set of particles whose positions and velocities are set to conform to the desired density field. Each particle represents a cloud of huge number of real particles. Positions and velocities of particles are subsequently integrated by various numerical codes. We have simulated a set of collisionless collapses of Gaussian density peaks by using the PM and P(3) M codes. We find that in cosmological simulations the physics at scales below the mean particle separation(MPS) is dominated by inaccuracies in describing the initial density field, and cannot be studied even by the high force-resolution codes. Since density fluctuations are ill-defined at scales smaller than MPS, it is ...

International Nuclear Information System (INIS)

The effects of catalytic metal additives on the hydrogen desorption properties of the submicrocrystalline magnesium hydride (#beta#-MgH_2) formed after hydrogenation of the Mg + 10 wt.%X (X = V, Y, Zr) mechanically (ball) milled composites were studied. The composites with catalytic metals were processed by controlled mechanical milling (CMM) in the magneto-mill Uni Ball Mill 5 under protective Ar atmosphere. X-ray diffraction of the milled powders revealed the formation of Mg nanograins (50-60 nm range) interdispersed with the nanograined metal additives within the powder particles. Scanning electron microscopy showed particle size reduction after milling. After activation and hydrogenation in a Sieverts-type apparatus under about 2 MPa pressure of hydrogen, the tetragonal #beta#-MgH_2 hydride co-exists with the small amount of retained unreacted Mg phase and the small amount of MgO in all three composites. The ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A complete study of an exploding bridgewire detonator (EBW), an LX-07 hemispherical booster and a PBX 9502 outer shell are described. Breakout times from all three are listed in terms of first impact on the booster, i.e., code times. Lucite windows are also used to obtain particle velocities at the edges of each explosive, and these are converted into explosive pressures. The key to modeling is the use of the profile of the aluminum detonator can as it impacts the booster, i.e., we need to know the curvature of the end of the booster can. Modeling even with coarse zoning shows that (i) using reactive flow in the booster is better than programmed burn, (ii) creating the flyer curvature helps, and (iii) creating the time differences of flyer impact helps even more.

International Nuclear Information System (INIS)

A series of spinel Li4Ti5O12 samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li4Ti5O12. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li4Ti5O12 with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li4Ti5O12 with L = 1.5 has an initial discharge capacity of 169 mAh g-1 and an initial charge-discharge ...

Science.gov (United States)

Magnetic particles have become very promising materials for drug delivery. However, preparation of magnetite particles with high surface area, biocompatibility, strong magnetic response, and suitable particle size still remains a major challenge. In this report, magnetite nanocrystal clusters with high surface areas were fabricated through a solvothermal process by introducing ammonium acetate as a porogen and trisodium citrate as a surface modification agent. The porosity, which was controlled by the reactant concentration, has been investigated in detail. The surface area of the nanocrystal clusters was as high as 141?m(2) g(-1) . Ibuprofen, as a model drug, was entrapped into the magnetite carriers. The interfacial interaction between the carboxylic groups on the drug molecules and the carboxylate groups on the carriers enhanced the loading efficiency. Low cytotoxicity in MCF-7 cell and in vitro ...

CERN Document Server

Canary Islands are normally interested by dominant North-East winds that, in some meteorological conditions, can transport sand at high altitude from the Sahara desert. The dust may affect the efficiency of the telescopes and decreases the transparency of the sky. In order to maximize the scientific return of the telescopes located at the ORM, we present an analysis of the atmospheric dust content and its effects on astronomical observations. B, V and I dust aerosol astronomical extinction are derived. Using a 5 years series database of data taken from the four channel TNG dust monitor, we compute a mean hourly and daily values of the dust content. We have detected particles having size 0.3, 0.5, 1.0 and 5.0 um. Using a power law we have derived the content of 10.0 um particles. We found a typical local dust concentration ranging from 3x10^6 particles per cubic meter at 0.3 um, to 10^3 at 5.0 um and 10 ...

Science.gov (United States)

Besides the multifunctionality, another equally important aspect of nanoparticles is their engineerability to control the geometrical and chemical properties during fabrication. In this work, we exploited this aspect to define asymmetric surface chemistry of an iron oxide nanosphere by controlling the topology of ligand expression on its surface resulting in a particle with two faces, one displaying only amines and the other only thiols. Specifically, amine-functionalized iron oxide nanospheres were attached on a solid support via a crosslinker containing a disulfide bridge. Liberation of the nanosphere using thiolytic cleavage created thiols on the portion of the particle's surface that interacted with the solid support. Employing a solid-phase strategy and a step-by-step addition of particles, the two unique faces on the same nanosphere served as fittings to assemble them into linear nano-chains. Assembly of chains with ...

Science.gov (United States)

The interaction of the globular protein lysozyme with silica nanoparticles of diameter 20 nm was studied in a pH range between the isoelectric points (IEPs) of silica and the protein (pH 3-11). The adsorption affinity and capacity of lysozyme on the silica particles is increasing progressively with pH, and the adsorbed protein induces bridging aggregation of the silica particles. Structural properties of the aggregates were studied as a function of pH at a fixed protein-to-silica concentration ratio which corresponds to a surface concentration of protein well below a complete monolayer in the complete-binding regime at pH > 6. Sedimentation studies indicate the presence of compact aggregates at pH 4-6 and a loose flocculated network at pH 7-9, followed by a sharp decrease of aggregate size near the IEP of lysozyme. The structure of the bridged silica aggregates was studied by cryo-transmission electron microscopy ...

Energy Technology Data Exchange (ETDEWEB)

The novel optical, electronic, and/or magnetic properties of metal and semiconductor nanoparticles have resulted in extensive research on new methods for their preparation. An ideal preparation method would allow the particle size, size distribution, crystallinity, and particle shape to be easily controlled, and would be applicable to a wide variety of material systems. Numerous preparation methods have been reported, each with its inherent advantages and disadvantages; however, an ideal method has yet to emerge. The most widely applied methods for nanoparticle preparation include the sonochemical reduction of organometallic reagents,(1&2) the solvothermal method of Alivisatos,(3) reactions in microemulsions,(4-6) the polyol method (reduction by alcohols),(7-9) and the use of polymer and solgel materials as hosts.(10-13) In addition to these methods, there are a variety of methods that take ...

International Nuclear Information System (INIS)

The measurements obtained here indicate ways in which micro-Raman spectroscopy can be used to elucidate structural characteristics and distribution of carbon in meteorites and interplanetary dust particles (IDPs). Existing information about structurally significant aspects of Raman measurements of graphite is combined with structurally relevant findings from the present micro-Raman studies of carbons prepared by carbonization of polyvinylidine chloride (PVDC) at various temperatures and natural material, as well as several acid residues from the Allende and Murchison meteorites in order to establish new spectra-structure relationships. Structural features of many of the materials in this study have been measured by x ray analysis and electron microscopy: thus, their structural differences can be directly correlated with differences in the Raman spectra. The spectral parameters consequently affirmed as indicators of structure are used as a measure of structure in ...

CERN Document Server

This is our response to a comment by Walter Eifler on our paper `A simple model for the short-time evolution of near-surface current and temperature profiles' (arXiv:physics/0503186, accepted for publication in Deep-Sea Research II). Although Eifler raises genuine issues regarding our model's validity and applicability, we are nevertheless of the opinion that it is of value for the short-term evolution of the upper-ocean profiles of current and temperature. The fact that the effective eddy viscosity tends to infinity for infinite time under a steady wind stress may not be surprising. It can be interpreted as a vertical shift of the eddy viscosity profile and an increase in the size of the dominant turbulent eddies under the assumed conditions of small stratification and infinite water depth.

CERN Document Server

The analysis of the linearization effect in multifractal analysis, and hence of the estimation of moments for multifractal processes, is revisited borrowing concepts from the statistical physics of disordered systems, notably from the analysis of the so-called Random Energy Model. Considering a standard multifractal process (compound Poisson motion), chosen as a simple representative example, we show: i) the existence of a critical order q* beyond which moments, though finite, cannot be estimated through empirical averages, irrespective of the sample size of the observation; ii) that multifractal exponents necessarily behave linearly in q, for q > q*. Tailoring the analysis conducted for the Random Energy Model to that of Compound Poisson motion, we provide explicative and quantitative predictions for the values of q* and for the slope controlling the linear behavior of the multifractal exponents. These quantities are shown to be related ...

British Library Electronic Table of Contents (United Kingdom)

Abstract The Eiffel Tower edifice is situated in the Lucky Strike hydrothermal vent field at a mean depth of 1690-m on the Mid-Atlantic Ridge (MAR). At this 11-m-high hydrothermal structure, different faunal assemblages, varying in visibly dominant species (mussels and shrimp), in mussel size and in density of mussel coverage, were sampled biologically and chemically. Temperature and sulphide (-S) were measured on the different types of mussel-based assemblages and on a shrimp-dominated assemblage. Temperature was used as a proxy for calculating total concentrations of CH4. Based on the physico-chemical measurements, two microhabitats were identified, corresponding to (i) a more variable habitat featuring the greatest fluctuations in environmental variables and (ii) a second, more stable, ...

Energy Technology Data Exchange (ETDEWEB)

In order to determine the viability of any Liquids from Coal (LFC) commercial venture, TEK-KOL and its partner, Mitsubishi Heavy Industries (MHI), have put together a technical and economic feasibility study for a commercial-size LFC Plant located at Zeigler Coal Holding Company`s North Rochelle Mine site. This resulting document, the ENCOAL Mild Coal Gasification Plant: Commercial Plant Feasibility Study, includes basic plant design, capital estimates, market assessment for coproducts, operating cost assessments, and overall financial evaluation for a generic Powder River Basin based plant. This document and format closely resembles a typical Phase II study as assembled by the TEK-KOL Partnership to evaluate potential sites for LFC commercial facilities around the world.

British Library Electronic Table of Contents (United Kingdom)

This study examined the oxygen permeation behavior of Ce0.9Gd0.1O2-d (Gadolinium-Doped Ceria, GDC)/Ba0.5Sr0.5Co0.8Fe0.2O3-d (BSCF) composite membranes fabricated using a conventional sintering technique. GDC/BSCF composite membranes with a relative density >95% could be obtained when a green compact of BSCF and GDC was sintered at 1150^oC for 5h. It appears that GDC serves as a grain growth inhibitor because the average grain size of the composite decreased with increasing GDC content. The oxygen permeability of the BSCF and GDC/BSCF composite membranes strongly depends on the grain size and membrane thickness. The addition of GDC to BSCF resulted in a small grain size, low thermal expansion coefficient and high hardness. However, it is believed that oxygen permeation was blocked by GDC, a...

International Nuclear Information System (INIS)

The T/sub c/ behavior of vapor-deposited Nb_3Ge and Nb_3Sn is examined as a function of low-fluence alpha-particle irradiation. It is found that for Nb_3Sn with rho_0approx.15 #mu##OMEGA#-cm the T/sub c/ is insensitive to low doses of radiation, whereas Nb_3Ge with rho_0approx.50 #mu##OMEGA#-cm has its T/sub c/ depressed immediately with irradiation. It is suggested that the T/sub c/ behavior of A-15 superconductors in the regime of small dose is strongly influenced by the initial state of the sample. Furthermore, it is argued that the behavior of the T/sub c/ with dose can be qualitatively explained by considering a sharp structure in the density of states N(E), the smearing of which by defects leads to a depression in T/sub c/.

Energy Technology Data Exchange (ETDEWEB)

Early diagnosis of hepatocellular carcinoma (hepatoma) along with surgical resection is the most appropriate therapeutic modality. For this purpose, there have been many reports concerning the diagnostic value of Lipiodol-CT scan. The authors selected 45 patients with hepatoma during the period of Feb.1986 to Jan. 1988 who received a conventional CT scan, hepatic angiography and a Lipiodol-CT scan. The results were as follows: 1. There was no statistical significant between serum AFP level and mass size, morphology and amount of necrosis. 2. Tumor necrosis was observed in a single massive and multinodular type when the tumor size exceeded 5 cm. 3. Pattern II on Lipiodol-CT, homogenous accumulation of Lipiodol except for the area of inner necrosis, was most frequently demonstrated, which means that a tumor mass with hypervascularity and increased blood flow will attract Lipiodol better. 4. Lipiodol-CT was superior to ...

International Nuclear Information System (INIS)

... v. 14(8) p. 624-625. azido compounds cadmium complexes potentiometry

Science.gov (United States)

The MISR instrument aboard NASA's Terra satellite participated in the UAE-2 campaign, August-October 2004. This campaign represented a unique opportunity to study the complex aerosol situation in the Arabian Gulf region, in the context of a first-rate collection of aircraft and surface-based instruments, giving us the opportunity to do some groundbreaking satellite aerosol validation work. We aimed (1) to validate MISR aerosol retrieval results for dust and pollution particles over dark and light surfaces, and (2) to contribute regional maps of aerosol optical thickness (AOT) and particle micro-physical properties, giving spatial context to the field-instrument measurements, and moving toward a satellite-based regional aerosol climatology. The validation effort benefited from the combination of an instrumented aircraft and a regional network of surface-based sun photometers. We obtained high-quality sub-orbital data coincident with MISR ...

Science.gov (United States)

A simple approach to controlling the loading percentage and size of zero-valent iron nanoparticles (ZVI NPs) immobilized within polyacrylic acid (PAA)/polyvinyl alcohol (PVA) nanofibrous mats for dye remediation applications is described. A functional "nanoreactor" comprised by electrospun PAA/PVA nanofibers served to bind ferric ions with the carboxyl groups of PAA, prior to their reduction to ZVI NPs. The resulting ZVI NP-immobilized hybrid polymer nanofibers were characterized using scanning electron microscopy, transmission electron microscopy, and thermogravimetric analysis. The morphology of the polymer nanofibers exhibited no appreciable change even after eight cycles of ferric ion binding/reduction, and the loading percentage and size of the ZVI NPs were controlled simply by varying the number of ferric ion binding/reduction cycles. Dye remediation experiments revealed that the decoloration effect of ZVI NPs immobilized within the ...

International Nuclear Information System (INIS)

A new generation of transmit-receive single-pass probes, denoted as C6 or X probe, was field tested during the Gentilly II, 2000 steam generator tube inspection. This probe has a performance equivalent to rotating probes and can be used for tubesheet and full-length inspection at an inspection speed equivalent to that of bobbin probes. Existing C3 transmit-receive probes have been demonstrated to be effective in detecting circumferential cracks. The C5 probe can detect both circumferential and axial cracks and volumetric defects but cannot discriminate between them. The C6 probe expands on the capabilities of both probes in a single probe head. It can simultaneously detect and discriminate between circumferential and axial cracks to satisfy different plugging criteria. It has excellent coverage, good defect detectability, and improved sizing and characterization. Probe data is displayed in C-scan format so that the amount of data to be analyzed ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The lignite used for Phase I of the project was a Texas lignite from the Martin Lake mine obtained from the stockpile for the Martin Lake Power Plant of the Texas Utilities Generating Company. The power requirements for the fluid-energy mill were determined from the measured steam (or air) temperatures, pressures and pressure drops and the lignite flow rate. The instrument locations for the tests are shown on Figure 1. All of the instruments were connected to a microcomputer via an analog input interface board. Data were recorded on disks periodically throughout the tests. Appropriate calibration procedures were followed to assure that reliable data were being obtained. The combined grinding/drying tests were conducted in Vicksbuth, MS at Ergon, Inc.'s fluid-energy-mill facility. both steam and air were used as grinding fluids. With steam, tests were used as grinding fluids. With steam, tests were run with the following temperatures maintained inside the pulverizer: 310/sup ...

Energy Technology Data Exchange (ETDEWEB)

A copyrighted computational fluid dynamics computer code, ICOMFLO, has been developed for the simulation of multiphase reacting flows. The code solves conservation equations for gaseous species and droplets (or solid particles) of various sizes. General conservation laws, expressed by elliptic type partial differential equations, are used in conjunction with rate equations governing the mass, momentum, enthalpy, species, turbulent kinetic energy, and turbulent dissipation. Associated phenomenological submodels of the code include integral combustion, two parameter turbulence, particle evaporation, and interfacial submodels. A newly developed integral combustion submodel replacing an Arrhenius type differential reaction submodel has been implemented to improve numerical convergence and enhance numerical stability. A two parameter turbulence submodel is modified for both gas and solid phases. An evaporation submodel treats ...

Energy Technology Data Exchange (ETDEWEB)

For an electron storage ring the beam size evaluation including beam-beam interaction gives an example of such a problem. Another good example is finding the beam size for a nonlinear machine. The present work gives a way to solve some of these problems, at least in principle. The approach described here is an application of the well known Green's function method, which in this case is applied to the Fokker-Planck equation governing the distribution function in the phase space of particle motion. The new step made in this paper is to consider the particle motion in two degrees of freedom rather than in one dimension, a characteristic of all the previous work. This step seems to be necessary for an adequate description of the problem, at least for the class of problems which are considered below. This work consists of the formal solution of the Fokker-Planck equation in terms of its ...

International Nuclear Information System (INIS)

In 65 adult rabbits of both sexes (2.5 to 6 kg) the following salvaging procedures were performed after simulated trauma: (1) Continuous suture line; (2) closure with fibrin sealant after temporary clamping; (3) hemisplenectomy with omental wrap; (4) suture fixation of fragments and slices of spleen tissue to the peritoneum; (5) suture fixation of spleen fragments to the omentum; (6) extraperitoneal subcutaneous transposition of spleen cubes. In addition, the likelihood of spontaneous splenosis was examined in a preliminary study involving 5 animals by introducing unattached spleen meal and fragments. Scanning was repeated 4 to 12 weeks postoperatively. The functional competence of minor parenchymal islands was also investigated with well counter measurements of organ and muscle tissue homogenates. Spontaneous splenosis after abdominal injuries was not found to be the rule. Salvaging procedures at the natural vascular hilus by sutures, fibrin sealant and hemisplenectomy produced ...

International Nuclear Information System (INIS)

This paper proposes an integrated method for using experimental data and CFD modeling to develop engineering correlations for atrium smoke management. Part I focused on the experimental program and validation of a CFD model of the experimental facility. Part II describes the extension of this model to a parametric study of balcony spill plumes. Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production or mass flow rate of the buoyant fire plume. One design issue is the mass flow rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes (BSPs) are based on a combination of one-tenth scale test data and theoretical analysis. The suitability of these correlations ...

Energy Technology Data Exchange (ETDEWEB)

Chemical composition of fine aerosol particles over the northern Chilean coastal waters was determined onboard the U.S. DOE G-1 aircraft during the VOCALS (VAMOS Ocean-Cloud-Atmosphere-Land Study) field campaign between October 16 and November 15, 2008. SO42-, NO3-, NH4+, and total organics (Org) were determined using an Aerodyne Aerosol Mass Spectrometer, and SO42-, NO3-, NH4+, Na+, Cl-, CH3SO3-, Mg2+, Ca2+, and K+ were determined using a particle-into-liquid sampler-ion chromatography technique. The results show the marine boundary layer (MBL) aerosol mass was dominated by non- sea-salt SO42- followed by Na+, Cl-, Org, NO3-, and NH4+, in decreasing importance; CH3SO3-, Ca2+, and K+ rarely exceeded their respective limits of detection. The SO42- aerosols were strongly acidic as the equivalent NH4+ to SO42- ratio was only ~0.25 on average. NaCl particles, presumably of sea-salt origin, showed chloride deficits but retained ...

International Nuclear Information System (INIS)

The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of higher than 2 W/m K were ...

International Nuclear Information System (INIS)

For the first time, rheological phase method, a simple and effective route, is applied to synthesize novel cathode material LiCoPO4. X-ray diffraction spectrometer (XRD), X-ray photoelectron spectrometer (XPS), transmission electron microscope (TEM) and electrochemical impedance spectroscopy (EIS) are taken to investigate this material, respectively. XRD figure shows that the rheological sample is better crystallized than the solid-state one. XPS result of the rheological sample exhibits that the valence of Co is 2+. TEM images show that better dispersed particles with smaller size can be formed by rheological method comparing to the solid-state route. Charge-discharge test is carried out in the range of 3.0-5.0 V at 0.2 mA cm-2. The initial discharge capacity for rheological phase and solid-state powder is 71.5 and 30.9 mAh g-1, respectively. The better electrochemical property should be ascribed to the better crystallized rheological phase ...

Energy Technology Data Exchange (ETDEWEB)

A comparison of the loss mechanisms in screen-printed solar cells relative to buried contact cells and cells with photolithography-defined contacts is presented in this paper. Model calculations show that emitter recombination accounts for about 0.5% absolute efficiency loss in conventional screen-printed cells with low-sheet-resistance emitters. Ohmic contact to high-sheet-resistance emitters by screen-printing has been investigated to regain this efficiency loss. Our work shows that good quality ohmic contacts to high sheet-resistance emitters can be achieved if the glass frit chemistry and Ag particle size are carefully tailored. The melting characteristics of the glass frit determine the firing scheme suitable for low contact resistance and high fill factors. In addition, small to regular Ag particles were found to help achieve a higher open-circuit voltage and maintain a low contact resistance. This work has resulted ...

Energy Technology Data Exchange (ETDEWEB)

This paper introduces a new method to produce nano-composite powder for the preparation of high performance ZnO varistors. ZnO particles were coated with Bi{sub 2}O{sub 3}, Sb{sub 2}O{sub 3}, Co{sub 2}O{sub 3}, Cr{sub 2}O{sub 3} and other additives via liquid nano-coating technique. Then the prepared powder was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermal gravity and differential scanning calorimetry (TG-DSC) and particle size distribution. The results showed that the ZnO composite powder is homogeneously coated and ultrafine. The densification, phase composition and microstructure of ZnO varistors was studied by linear shrinkage, X-ray diffraction (XRD) and SEM, respectively. The preliminary electrical parameters of ZnO varistors showed that the breakdown voltage V {sub b} (1 mA/cm{sup 2}) and nonlinear coefficient {alpha} is 5400 V/cm and 50, respectively, much ...

Science.gov (United States)

Under the auspices of the DOE and private industry, considerable progress has been made in: preparation of coal-water fuels; combustion of low-ash coal-based fuel forms; processes to provide deeply-cleaned coal. Developments in advanced beneficiation of coal to meet stringent requirements for low ash and low sulfur can be anticipated to further complicate the problem areas associated with this product. This is attributable to the beneficiated coal being procured in very fine particles with high surface areas, modified surface characteristics, reduced particle size distribution range, and high inherent moisture. Experience in the storage, handling, and transport of highly beneficiated coal has been limited. This is understandable, as quantities of such product are only now becoming available in meaningful quantities. During this reporting period the authors have: developed a suite of empirical tests covering water retention, ...

Energy Technology Data Exchange (ETDEWEB)

Experiments on manganese removal using an aerated granular filter with mean particle size of 3.68 mm and 5.21 mm anthracite were conducted at a filtration rate of 100 m d{sup -1}. Air, with a rate of 0 to 366 m d{sup -1}, was supplied through nozzles positioned 100 mm above the filter column bottom. From the experiments that were conducted, it was found that manganese removal is completed at a pH of 9.6 or above. In addition, the oxidation and removal rate of dissolved manganese were expressed as a first-order reaction. The smaller the filter media particles were, the higher the manganese removal efficiency was. The aeration rate of dissolved oxygen in raw water is sufficient for the manganese removal process. The manganese removal rate increased with time due to the catalytic effect of manganese dioxide (MnO{sub 2}) attached to the media. The x-ray diffraction analysis showed that the solids attached to the filter media ...