Energy Technology Data Exchange (ETDEWEB)

NUPEC has carried out hydrogen mixing tests to investigate hydrogen distribution behavior within a model containment and to provide a set of experimental data for validation of severe accident analysis codes.

International Nuclear Information System (INIS)

Liquid sodium is used as coolant in Fast Breeder Reactors (FBR). There is a likelyhood of sodium spillage in ambient air in the Steam Generator Building (SGB) of the FBR plant. Due to high chemical reactivity with oxygen, especially at temperatures greater than 573 K, it catches fire very easily. In order to carryout safety related experimental studies for different modes of sodium fires and to develop suitable mathematical models for the assessment of their consequences, an experimental facility (SFEF, Sodium Fire Experimental Facility) is being setup a IGCAR, Kalpakkam. The SFEF is having a 540 m"3 volume experimental hall. Stainless steel linear will be provided on the inside surfaces of experimental hall walls, ceiling and floor. Analysis has been carried out for enclosed sodium pool fire scenarios in SFEF by using sodium pool fire code SOFIRE II, which ...

International Nuclear Information System (INIS)

This paper proposes an integrated method for using experimental data and CFD modeling to develop engineering correlations for atrium smoke management. Part I focused on the experimental program and validation of a CFD model of the experimental facility. Part II describes the extension of this model to a parametric study of balcony spill plumes. Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production or mass flow rate of the buoyant fire plume. One design issue is the mass flow rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes (BSPs) are based on a combination of ...

International Nuclear Information System (INIS)

The COSA II (computer codes for salt) benchmark problem has been pursued with the ADINA (Automatic Dynamic Incremental Nonlinear Analysis) program code. With the use of this, the code should be validated by means of experimental data and the ability to reproduce real-life calculation results of the KfK (Kernforschungszentrum Karlsruhe/Nuclear Research Center in Karlsruhe) should be proven. A successful validation of the code then forms the foundation stone for the ability to use different calculation problems in the final (ultimate) storage. This also accompanies the consequent reaction of replacing the STEALTH (Solids and Thermal Hydraulics Code for EPRI Adapted from LAGRANGE TOODY and HEMP) program which has a number of program-specific weaknesses compared to the ADINA computer code. In order to reproduce the approximate values from the KfK, the same values have been used. Differences were evident in ...

International Nuclear Information System (INIS)

The credibility of the model proposed by Ghosh in predicting the refractive indices of mixed semiconductor crystals of technological importance within their miscibility range as a function of band gap is demonstrated. The high-frequency refractive indices of four quaternary alloys Al_xGa_1_-_x_-_yIn_yP (y = 0.49, 0 #<=# x #<=# 0.51), InSb_xAs_1_-_x_-_yP_y (y = 2.2x, 0 #<=# x #<=# 0.313, 0 #<=# y #<=# 0.638), Cd_xZn_1_-_x_-_yHg_ySe (x + y = 1, 0.153 #<=# x #<=# 0.684, 0.316 #<=# y #<=# 0.847), and CdS_1_-_x_-_ySe_xTe_y (x + y = 1, 0.15 #<=# x #<=# 0.93, 0.07 #<=# y #<=# 0.85) are calculated according to the relation n"2-1 = A/(E_g + B)"2 where A is an energy gap dependent constant and B is a constant depending on crystal ionicity. The calculated values show excellent agreement with the experimental data thus justifying the validity of the model.

British Library Electronic Table of Contents (United Kingdom)

The aim of this work is the development and experimental validation of a detailed dynamic fuel cell model using the gPROMS modeling environment. The model is oriented towards optimization and control and it relies on material and energy balances as well as electrochemical equations including semi-empirical equations. For the experimental validation of the model a fully automated and integrated hydrogen fuel cell testing unit was used. The predictive power of the model has been compared with the data obtained during load change experiments. A sensitivity analysis has been employed to reveal the most critical empirical model parameters that should be estimated using a systematic estimation procedure. Model predictions are in good agreement with experimental data under a wide range of operati...

Energy Technology Data Exchange (ETDEWEB)

Piping in nuclear power plants is vital to the proper operation and safety of these facilities. To assure safety in the unlikely event of a pipe break, it is necessary to evaluate the consequences from the resulting whipping pipe on neighboring components and structures. Numerical simulations allow for rapid evaluation of these consequences. Before simulations can be accepted, however, the methodology and computer codes must be validated against experimental results. This paper uses a probabilistic approach to validate pipe whip simulations against limited experimental results. Probabilistic analysis software was developed and coupled to existing deterministic finite element software. An example of a whipping pipe impacting against a reinforced concrete slab was simulated. The described probabilistic approach was used to validate the numerical simulations. The conclusions obtained ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the biosorption of Cd(II), Ni(II) and Pb(II) on Aspergillus niger in a batch system was investigated, and optimal condition determined by means of central composite design (CCD) under response surface methodology (RSM). Biomass inactivated by heat and pretreated by alkali solution was used in the determination of optimal conditions. The effect of initial solution pH, biomass dose and initial ion concentration on the removal efficiency of metal ions by A. niger was optimized using a design of experiment (DOE) method. Experimental results indicated that the optimal conditions for biosorption were 5.22 g/L, 89.93 mg/L and 6.01 for biomass dose, initial ion concentration and solution pH, respectively. Enhancement of metal biosorption capacity of the dried biomass by pretreatment with sodium hydroxide was observed. Maximal removal efficiencies for Cd(II), Ni(III) and ...

Energy Technology Data Exchange (ETDEWEB)

Independent isomeric yield ratios of {sup 131}Te, {sup 133}Te and {sup 134}I have been determined at five different energies in the range of 25-44 MeV alpha particle induced fission of {sup 238}U using radiochemical and gamma spectrometric techniques. From the independent isomeric yield ratios, fragment angular momenta (J{sub rms}) have been deduced using a statistical model analysis. The J{sub rms} were also calculated theoretically based on thermal equilibration of various collective modes after considering the occurrence of multichance fission. These data and the literature data for various fragments in the mass region 126-136 in {sup 238}U ({alpha},f), {sup 238}U (p,f) and {sup 238}U ({gamma},f) show the following important features: (i) Both the entrance channel excitation energy and input angular momentum affect the fragment angular momentum in the exit channel. (ii) There are two groups of fission products from the point of view of change of fragment angular ...

International Nuclear Information System (INIS)

Experimental results are presented on the quasi-statistic polarization reversal and on the effect of high dc electric field on the behaviour of LiNH_4SO_4 and LiND_4SO_4 monocrystals, namely in the vicinity of the II-III phase transformation.

UK PubMed Central (United Kingdom)

Type II collagen-induced arthritis (CIA) in mice is an autoimmune experimental model for rheumatoid arthritis. Susceptibility to CIA is associated with certain major histocompatibility complex class...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A rigorous mathematical model is developed to describe chemical absorption of carbon dioxide in a falling-film micro-contactor. Contrary to previous models described in literature, hydrodynamics in both phases is accurately captured by the Navier-Stokes equations. By this means, backmixing effects can be accounted for. Furthermore, the interface position is determined directly using the level-set method. The developed model is validated with experimental data obtained from literature and a good agreement is established. With the validated model, detailed studies are performed to investigate the impact of process parameters.

Energy Technology Data Exchange (ETDEWEB)

This dissertation is concerned with the development, experimental diagnostics and mathematical modelling and simulation of polymer electrolyte fuel cells (PEFC). The central themes throughout this thesis are the closely interlinked phenomena of mass and charge transfer. In the face of developing a PEFC system for vehicle propulsion these phenomena are scrutinized on a broad range of relevant scales. Starting from the material related level of the membrane and the gas diffusion layer (GDL) we turn to length scales, where structural features of the cell additionally come into play. These are the scale of flow channels and ribs, the single cell and the cell stack followed by the cell, stack, and system development for an automotive power train. In Chapter 3 selected fundamental material models and properties, respectively, are explored that are crucial for the mathematical modelling and simulation of PEFC, as needed in some succeeding parts of this work. First, ...

International Nuclear Information System (INIS)

Compared with that of Daya Bay Nuclear Power Plant, the reactor power of QS-II Nuclear Power Plant is decreased and the primary coolant system is changed from three loops to two loops. Thereby the related systems were re-designed, and corresponding tests and engineering validation were carried out. Results of preliminary operation indicate that it is successful. The author describes the design modifications, features and corresponding tests of some systems, reflecting the successful incorporation of engineering and testing, and revealing the capability to develop nuclear power and design the large or medium sized commercial NPP on Self-Reliance in China

Energy Technology Data Exchange (ETDEWEB)

The biosorption characteristics of Pb(II) and Cd(II) ions from aqueous solution using the green alga (Ulva lactuca) biomass were investigated as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by U. lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of U. lactuca biomass for Pb(II) and Cd(II) ions was found to be 34.7 mg/g and 29.2 mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 10.4 kJ/mol for Pb(II) biosorption and 9.6 kJ/mol for Cd(II) biosorption, indicating that the biosorption of both metal ions was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, ...

International Nuclear Information System (INIS)

The objective of this project is to develop multi-dimensional computational models in order to improve the operation of uranium electrorefiners currently used in pyroprocessing technology. These 2-D (US) and 3-D (ROK) mathematical models are based on the fundamental physical and chemical properties of the electrorefiner processes. The validated models by compiled and evaluated experimental data could provide better information for developing advanced electrorefiners for uranium recovery. The research results in this period are as follows: - Successfully assessed a common computational platform for the modeling work and identify spatial characterization requirements. - Successfully developed a 3-D electro-fluid dynamic electrorefiner model. - Successfully validated and benchmarked the two multi-dimensional models with compiled experimental data sets

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.

DEFF Research Database (Denmark)

The determination of conformational preferences in unfolded and disordered proteins is an important challenge in structural biology. We here describe an algorithm to optimize energy functions for the simulation of unfolded proteins. The procedure is based on the maximum likelihood principle and employs a fast and efficient gradient descent method to find the set of parameters of the energy function that best explain the experimental data. We first validate the method by using synthetic reference data, and subsequently apply the algorithms to data from nuclear magnetic resonance spin-labeling experiments on the Delta 131 Delta fragment of Staphylococcal nuclease. A significant strength of the procedure that we present is that it directly uses experimental data to optimize the energy parameters, without relying on the availability of high resolution structures. The procedure is fully general and can be applied to a range of ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a numerical simulation with the EUROPLEXUS fast dynamics software of a pipe whipping phenomenon occurring in the thermal hydraulic conditions of a loss of coolant accident in a PWR primary circuit. Different physical phenomena take place simultaneously during the rupture and the whipping of the pipe such as plasticity, contact, large displacements, two-phase flow regime and fluid structure interaction. Two kinds of numerical models - a simplified pipeline model and a mixed 1D/3D model - are considered and compared throughout modelling and computation. Numerical results are compared with experimental data belonging to the Aquitaine II test campaign.

Energy Technology Data Exchange (ETDEWEB)

It is both experimentally and theoretically demonstrated that ion flow velocity at an arbitrary angle with respect to the magnetic field can be measured with a directional Langmuir probe. Based on the symmetry argument, we show that the effect of magnetic field on directional probe current is exactly canceled in determining the ion flow velocity, and obtain the generalized relation between flow velocity and directional probe currents valid for any flowing direction. The absolute value of the flow velocity is determined by an in situ calibration method of the probe. The applicability limit of the present method to a strongly ion-magnetized plasma is experimentally examined. (author)

Energy Technology Data Exchange (ETDEWEB)

With the aim of an experimental check on the validity of the theory of molecular recognition, the authors have carried out the chemical-enzymatic synthesis and cloning of the gene of human calcitonin and also of the genes of antisense polypeptides to human calcitonin and miniproinsulin. It has been shown that recombinant plasmids obtained on the basis of these synthetic genes are capable of ensuring the biosynthesis of the given polypeptides in E. coli cells as hybrid proteins with the IgG-binding domain of staphylococcal protein A.

International Nuclear Information System (INIS)

Two sets of analytical correlations describing transitions between two-phase flow regimes are reviewed and discussed. One, the T-D set, is based on mechanistic models; the other, the Weisman set, on experimental correlations. The T-D set is preferred for horizontal flow, whereas the Weisman set seems preferrable for vertical flow. A computer code (FLOP) based on the T-D theory is described and applied to validate the theory.

Energy Technology Data Exchange (ETDEWEB)

A total of 86 experimental fuel pins with various fuel, liner, and cladding candidate materials have been irradiated in the Experimental Breeder Reactor-II (EBR-II) and the Fast Flux Test Facility (FFTF) reactor as part of the SP-100 fuel pin irradiation testing program. Postirradiation examination results from these fuel pin are key in establishing performance correlations and demonstrating the lifetime and safety of the reactor fuel system. This paper provides a brief description of the in-reactor fuel pin tests and presents the most recent irradiation data on the performance of wrought rhenium (Re) liner material and high density UN fuel at goal burnup of 6 atom percent (at. %). It also provides an overview of the significant variety of other fuel/liner/cladding combinations which were irradiated as part of this program and which may be of interest to more advanced efforts.

Energy Technology Data Exchange (ETDEWEB)

Monte Carlo neutron transport methods can be used to verify the applicability of point kinetics for safety analysis of nuclear reactors. KENO-NR was used to obtain the transfer function of the Advanced Neutron Source reactor and the time delay between the core power production and the external detectors, a parameter of interest to the safety systems design. The good agreement between the Monte Carlo generated transfer function and the point kinetics transfer function validates that the uncommon ANS geometry does not preclude the use of point kinetics in the frequency range that was investigated. Various features of the power spectral densities also demonstrated the applicability of point kinetics. The time delay was obtained from the cross-power spectral density (CPSD) and is {approximately}15 ms. These analyses show that frequency analysis can be used experimentally to investigate the validity of the use of point kinetics ...

British Library Electronic Table of Contents (United Kingdom)

A mathematical model was developed to predict a moisture content profile during the thick layer re-wetting process of brown rice unpackaged and packaged with low density polyethylene (LDPE) and polybutylene terephthalate (PBT) films. Model validation was carried out by comparing predicted with measured moisture content derived from relative humidity data obtained from the brown rice re-wetting test for 6days at 25degreeC and 90% RH. The moisture standard errors of the model validation for brown rice packaged in LDPE and PBT films were 0.08% wet basis (wb) and 0.11%wb, respectively. It was concluded that the proposed re-wetting model could successfully describe the thick layer re-wetting of brown rice under the experimental conditions. Using this model, re-wetting simulations were carried o...

Energy Technology Data Exchange (ETDEWEB)

The PERMCAT process chosen for the final clean-up stage of the Tokamak Exhaust Processing system of the ITER tritium plant combines in a single component a catalytic reactor and a permeator using Pd/Ag membranes. This study covers the mechanical behaviour of a Pd/Ag membrane under different operating conditions. The consequences of hydrogen uptake by the membrane during nominal operation but also during off-normal events are presented. Depending on the operating conditions, expansions around 2% and significant deformations are observed. Different mechanical designs of PERMCAT reactors are then discussed. The first generation comprises finger-type membranes and two new mechanical designs use either additional edge welded bellows or a special corrugated Pd/Ag membrane. These upgraded designs improve the robustness and simplify the geometry of the component. The experimental validation of these new units has been carried out based on the ...

Energy Technology Data Exchange (ETDEWEB)

The thermal contact resistance between balls and inner and outer rings of thermally steady space-use deep groove ball bearings was studied experimentally to verify the validity of the previously proposed calculation method for the resistance. The 440C stainless steel single row bearing was used for measuring its steady state temperature distributions in a vacuum environment under axial, radial and combined load conditions. As a result, the experimental results of the resistance well agreed with calculated ones under each load condition resulting in the sufficient validity at nearly the same surface roughness. It was necessary to apply a static equivalent radial load to calculation under the combined load that a contact angle is larger than the angle of resultant force dependent on both load components. In experiments under only radial load, measurement of outer ring temperatures was necessary at some ...

British Library Electronic Table of Contents (United Kingdom)

The L shell fluorescence cross-sections of the elements in range 45Z50 have been determined at 8keV using Synchrotron radiation. The individual L X-ray photons, Ll, La, LbI, LbII, LgI and LgII produced in the target were measured with high resolution Si(Li) detector. The experimental set-up provided a low background by using linearly polarized monoenergetic photon beam, improving the signal-to-noise ratio. The experimental cross-sections obtained in this work were compared with available experimental data from Scofield [1,2] Krause [3,4] and Scofield and Puri et al. [5,6]. These experimental values closely agree with the theoretical values calculated using Scofield and Krause data, except for the case of Lg, where values measured of this work are slighter higher.

British Library Electronic Table of Contents (United Kingdom)

The electroreduction process of Zr(IV) was studied at molybdenum electrode in LiCl-KCl-K2ZrF6 molten salt. The transient electrochemical techniques, such as cyclic voltammetry and chronopotenimetry were used. The experimental results showed that the electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both diffusion-controlled process. In the 773-973K range, the diffusion coefficients of Zr(ii) and Zr(IV) were determined: DZr(II)=0.15567exp{-69.65x10^3RT(K)}cm^2/s, DZr(IV)=1.09x10^-^4exp{-44.39x10^3RT(K)}cm^2/s. The activation energy values for the diffusion process were 69.65kJ/mol and 44.39kJ/mol, respectively.

International Nuclear Information System (INIS)

This report provides a summary of theoretical and experimental studies of actinide spectra in condensed phases. Much of the work was accomplished at Argonne National Laboratory, but references to related investigations by others are included. Spectroscopic studies of the trivlent actinides are emphasized, as is the use of energy level parameters, evaluated from experimental data, to investigate systematic trends in electronic structure and other properties. Some reference is made to correlations with atomic spectra, as well as with spectra of the (II), (IV), and higher valence states. 207 refs., 39 figs., 38 tabs.

CERN Document Server

Methods and Procedures for the Verification and Validation of Artificial Neural Networks

International Nuclear Information System (INIS)

The present paper is concerned with development and application of a so-called Effective Convection Model (ECM), which aims to provide a detailed, mechanistic description of heat transfer processes in a BWR lower plenum. The ECM is a Computational Fluid Dynamics (CFD)-like tool which employs a simpler and more effective approach to compute heat transfer by solving only energy conservation equation instead of solving the full set of Navier-Stokes and energy equations by a CFD code. We implement the ECM in a CFD code (Fluent), with detailed description of the ECM development, implementation and validation. A dual approach is used to validate the ECM, namely validation against experimental data and against heat transfer results obtained by CFD predictions in the same geometries and conditions. Insights gained from CFD simulations are also used to improve ECM. The ECM capability as an effective tool to ...

CERN Document Server

This is our response to a comment by Walter Eifler on our paper `A simple model for the short-time evolution of near-surface current and temperature profiles' (arXiv:physics/0503186, accepted for publication in Deep-Sea Research II). Although Eifler raises genuine issues regarding our model's validity and applicability, we are nevertheless of the opinion that it is of value for the short-term evolution of the upper-ocean profiles of current and temperature. The fact that the effective eddy viscosity tends to infinity for infinite time under a steady wind stress may not be surprising. It can be interpreted as a vertical shift of the eddy viscosity profile and an increase in the size of the dominant turbulent eddies under the assumed conditions of small stratification and infinite water depth.

British Library Electronic Table of Contents (United Kingdom)

A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat e...

International Nuclear Information System (INIS)

A quadruply redundant synchronous fault tolerant processor (FTP) is now under fabrication at the C.S. Draper Laboratory to be used initially as a trip monitor for the Experimental Breeder Reactor EBR-II operated by the Argonne National Laboratory in Idaho Falls, Idaho. The real time operating system for this processor is described.

Energy Technology Data Exchange (ETDEWEB)

Experimental results of a search for the {Xi}{sub 3/2}(1860) cascade pentaquark state in data collected with the CDF 2 Detector in Run II at the Tevatron are presented. No evidence for these states in the neutral {Xi}{sup -}{pi}{sup +} and doubly charged {Xi}{sup -}{pi}{sup -} modes has been found. Preliminary upper limits on yields at 1862 MeV/c{sup 2} relative to the well established resonance {Xi}*(1530){sup 0} are presented.

Energy Technology Data Exchange (ETDEWEB)

During the years 1995-1999, an international effort was going on under the title DECOVALEX II, in order to study the coupled thermo-hydro-mechanical (THM) effects in the water containing fractured rock mass caused by the heat generation of spent fuel canisters in a repository. The project was a continuation project of DECOVALEX (1991-1996). The name comes from the acronym 'an international co-operative project for the DEvelopment of COupled models and their VALidation against EXperiments in nuclear waste isolation'. Radiation and Nuclear Safety Authority (STUK) was one of the eleven Funding Organizations in the international project. STUK's Research Team was the Technical Research Centre of Finland, VTT Communities and Infrastructure. To support and coordinate the national research work, STUK formed a National DECOVALEX II Group (NDG). The group had representatives from six research organisations ...

Energy Technology Data Exchange (ETDEWEB)

Precondition for the low-NO operation of gas turbine burners is the generation of as homogeneous as possible a gaseous fuel/air mixture. Such a burner behavior can be achieved by selective adaptation of the flow and injection. A computing model is introduced that calculates the dynamically balanced GASs/droplet flow through numerical solution of the transport equations in a curved orthogonal coordinate system. The feedback reaction of the fuel droplets to the gas phase is considered by source terms and/or sink terms. Test computations were carried out for comparison with analytical solutions from the flow mechanics and validated by comparison with measurement results. Droplet motion and evaporation were checked by means of published experimental results on single droplets. For the validation of the developed computing technique, model tests were carried out with water in place of fuel. It is pointed out that the choice of ...

International Nuclear Information System (INIS)

The Melt Vessel Interaction (MVI) project is concerned with the consequences of the interactions that a core melt, generated during a postulated severe accident in a light water reactor, may have with the pressure vessel. In particular, the issues concerned with the failure of the vessel bottom head are the focus of the research. The specific objectives of the project are to obtain data and develop validated models, which could be applied to prototypic plants, and accident conditions, for resolution of issues related to the melt vessel interactions. The project work has been performed by nine partners having varied responsibility. The work included a large number of experiments, with simulant materials, whose observations and results are employed, respectively, to understand the physical mechanisms and to develop validated models. Applications to the prototypic geometry and conditions have also been performed. This report is volume 1 of the ...

CERN Document Server

The nucleation and propagation of hydrofractures by injection of over pressured fluids in an elastic and isotropic medium are studied experimentally. Non-Newtonian fluids are injected inside a gelatine whose mechanical properties are assumed isotropic at the experimental strain rates. Linear elastic theory predicts that plastic deformation associated to breakage of gelatin bonds is limited to a small zone ahead of the tip of the propagating fracture and that propagation will be maintained while the fluid pressure exceeds the normal stress to the fracture walls (Ch\\'avez-\\'Alvarez,2008) (i.e., the minimum compressive stress), resulting in a single mode I fracture geometry. However, we observed the propagation of fractures type II and III as well as nucleation of secondary fractures, with oblique to perpendicular trajectories with respect to the initial fracture. In the Video (http://hdl.handle.net/1813/14122) ...

Energy Technology Data Exchange (ETDEWEB)

The present paper is concerned with the prediction method for the motions and tensions of mooring lines on slack-moored floating oceanic architectural building in coastal zone. The motions and the tensions of mooring lines were estimated by the time domain numerical simulation in the present method. The present method includes the nonlinearity of mooring system, slow varying wave drift force. The authors performed a time domain numerical simulation for motions and the tensions of mooring lines on floating barge in two component waves. Also, the results obtained by numerical simulation were compared with the experimental results. The validity of the present method was confirmed.

Science.gov (United States)

We have developed a novel laser ray-tracing method to measure aberrations in optical systems. It consists of delivering narrow laser pencils (by a laser scanner), recording the spots that are formed on the image plane (with a CCD camera), and computing the position of each centroid. This approach could be considered an experimental (approximate) implementation of standard numerical ray tracing. Several tests and experiments, including a direct comparison with a Hartmann-Shack wave-front sensor, provided highly satisfactory results that confirmed the validity of the method and revealed potential advantages. PMID:18073906

Science.gov (United States)

This study presents a theoretical analysis of heat generation and dissipation of field-controllable magneto-rheological fluid (MRF) shock absorbers. Since MRF dampers are energy- dissipating devices, the issues of heat generation and dissipation are important in predicting their performance. A theoretical model is developed based on Bingham plastic model to estimate temperature history of the MRF dampers. The governing equation includes the MRF viscosity as a function of the temperature. The numerical solutions are compared with experimental results in order to validate the accuracy of the model, and excellent agreements are obtained.

Energy Technology Data Exchange (ETDEWEB)

Neutron deficient nuclei with mass numbers A {approx} 90 and 40 {<=} Z {<=} 44 have been studied making use of the Osiris and Nordball spectrometers. The high spin states of these nuclei and their electromagnetic decay properties are compared to shell model calculations based on the core {sup 88}Sr and using different parametrizations of the residual interaction. The dependence of the mean square deviations of experimental and theoretical level energies, branching ratios, and transition probabilities on the neutron numbers N = 46-50 and the validity of seniority as a good quantum number are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The development of detailed chemical kinetic reaction mechanisms for analysis of autoignition and knocking of hydrocarbon fuels is described. In particular, kinetic processes of concern for the oxidation of complex hydrocarbon fuel molecules are emphasized. The wide ranges of temperature and pressure which are encountered by end gases in automobile engine combustion chambers result in extreme demands on reaction mechanisms which are intended to describe knocking conditions and predict rates of combustion and ignition. The reactions and chemical species which are most important in each temperature and pressure regime are discussed, and the validation of these reaction mechanisms through comparison with idealized experimental results is described. 53 refs., 8 figs., 5 tabs.

Science.gov (United States)

We report results of measurements and analysis of the heat capacity of MnSi. The measurements included data collection at a magnetic field of 4T, which suppresses strongly the longitudinal spin fluctuations and the phase transition. To analyze the experimental data, calculations of the phonon spectrum and phonon density of states in MnSi were performed. Inelastic neutron scattering with a polycrystalline sample of MnSi was used to validate the computational results. The combination of the experimental and theoretical data turned out to be decisive in revealing some hidden features of the thermal excitations in MnSi. In particular, the analysis of the available data led conclusively to the existence of a negative contribution to the heat capacity and entropy in MnSi at T>Tc, implying that a specific spin ordering process did occur in the paramagnet phase of MnSi.

Energy Technology Data Exchange (ETDEWEB)

Recently it was demonstrated that long-lived quantum coherence exists during excitation energy transport in photosynthesis. It is a valid question up to which length, time and mass scales quantum coherence may extend, how one may detect this coherence and what, if any, role it plays in the dynamics of the system. Here we suggest that the selectivity filter of ion channels may exhibit quantum coherence, which might be relevant for the process of ion selectivity and conduction. We show that quantum resonances could provide an alternative approach to ultrafast two-dimensional (2D) spectroscopy to probe these quantum coherences. We demonstrate that the emergence of resonances in the conduction of ion channels that are modulated periodically by time-dependent external electric fields can serve as signatures of quantum coherence in such a system. Assessments of experimental feasibility and specific paths towards the experimental ...

Science.gov (United States)

In terms of the reduced potential energy barrier ? = ?uTS/kT, the rate coefficients for chemical reactions are usually expressed as proportional to e-?. The coupling between vibrational modes of the medium to the reaction coordinate leads to a proportionality of the regularized gamma function of Euler Q(a,?) = ?(a,?)/?(a), with a being the number of modes coupled to the reaction coordinate. In this work, the experimental rate coefficients at various temperatures for several chemical reactions were fitted to the theoretical expression in terms of Q(a,?) to determine the extent of its validity and generality. The new expression affords lower deviations from the experimental points in 29 cases out of 38 and it accounts for the curvature in the logarithmic plots of rate coefficients versus inverse temperature. In the absence of tunneling, conventional theories predict the curvature of these plots to be identically zero.

British Library Electronic Table of Contents (United Kingdom)

This paper presents a new method of extracting biologic particles from a mixture of particles. The method is based on the pumping effect in a p-shaped ultrasonic actuator, which has a gap between its two vibrating metal plates. An adhesive tape is placed at a proper position in the gap. Due to the pumping effect which is induced by the sound field in the gap, the particles with smaller mass and radius in the mixture can be pumped up to reach the adhesive tape; while the ones with larger mass cannot. Therefore, the particles with smaller mass and radius can be extracted from the mixture. A theoretical model which can well explain the operation principle and experimental phenomena is developed. By the experimental results and the theoretical analyses based on the model, the validity of the m...

British Library Electronic Table of Contents (United Kingdom)

The present paper concerns the development of a polymer electrolyte membrane (PEM) fuel cells model in order to analyse the behaviour of the cell varying its operating parameters such as temperature (70-120 ^oC), pressure (1-3 atm), relative humidity (35-100%) and CO content (0-200 ppm) in the feeding gas. The voltage output and the relative current of a generic PEM fuel cell has been predicted through a mathematical method based on semi-empirical correlations derived from the experimental data available in literature. The model has been implemented in a commercial process simulator (AspenPlus) and it has been validated by comparing the obtained results with further experimental data (not utilized for the model development). The comparison has underlined a good agreement with the experimen...

Science.gov (United States)

The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and polidal rotation in the high-beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10/sup 6/ cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal-plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10/sup 6/ cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collisional, Pfirsch-Schluter regime. The poloidal motion, however, results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the ...

CERN Document Server

Phase II collimators will complement the existing system to improve the expected high RF impedance and limited efficiency of Phase I jaws. An international collaborative effort has been launched to identify novel advanced materials responding to the very challenging requirements of the new collimators. Complex numerical calculations simulating extreme conditions and experimental tests are in progress. In parallel, an innovative modular design concept of the jaw assembly is being developed to allow fitting in alternative materials, minimizing the thermally induced deformations, withstanding accidents and accepting high radiation doses. Phase II jaw assembly is made up of a molybdenum back-stiffener ensuring high geometrical stability and a modular jaw split in threes sectors. Each sector is equipped with a high-efficiency independent cooling circuit. Beam position monitors (BPM) are embedded in the jaws to fasten setup time ...

Science.gov (United States)

Batch interaction experiments were performed under aerobic conditions to characterize the adsorption behavior and valence speciation of CoEDTA complexes (equimolar at 10 -5 mol/L) in a series of Pliocene subsurface sediments containing various amounts of Fe and Mn oxides. The experiments were performed in 0.003 mol/L Ca(ClO 4 ) 2 with a solids concentration of 500 g/L at variable pH (4-9) and at the natural pH of the sediments (pH = 8.3). Three of these subaerial sediments (Ringold 1, 2, 3) contained significant quantities of extractable Fe and Mn, while the fourth (Ringold 4) was virtually devoid of sesquioxide precipitates. Microscopic and mineralogic analyses of the most heavily encrusted material (Ringold 2) showed that the oxides existed as intergrain cements and contained crystalline goethite and rancieite/todorokite. Adsorption on a synthetic analog sorbent (0.6 mass % ferrihydrite-coated sand) over a range in pH showed that, while both Co(II)EDTA 2- and ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a 400-MWt, sodium-cooled reactor located on the Hanford Site near Richland, Washington, USA. The FFTF is owned by the U.S. Department of Energy and is operated by the Westinghouse Hanford Company. The FFTF was designed to test fuels and materials for use in liquid metal reactors. Since initial operation in 1982, anticipated breaches of experimental fuel pins have released fission products, including cesium, into the primary sodium. Because of its high volatility, cesium vaporizes into the cover gas space, where it condenses on components and equipment and is transported into the cover gas outlet. Because of the long half-life of "1"3"7Cs, these deposits result in long-term, local radiation levels that make contact maintenance difficult. Thus, a cesium trap was installed in FFTF to reduce the cesium level in the sodium. The trap could also permit a Run Beyond Cladding Breach (RBCB) program without compromising the sodium purity. ...

Science.gov (United States)

A computer program entitled "Marshall Aerospace Vehicle Representation in C II,

International Nuclear Information System (INIS)

Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production rate of the buoyant fire plume. One design issue is the smoke production rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes are based on a combination of one-tenth scale test data and theoretical analysis. Questions have arisen over the suitability of these correlations for real-scale designs. A combined program of full-scale experimentation and CFD modeling is being conducted to analyze the accuracy of these correlations. A full-scale experimental facility was constructed with a 5 m by 5 m by 15 m fire compartment connected to a four-story atrium. Propane fires in the ...

Energy Technology Data Exchange (ETDEWEB)

The 1.04 GeV-proton elastic scattering from /sup 40/Ca is studied in the framework of the coherent density fluctuation model (CDFM). The calculations are carried out in the Glauber theoretical scheme with three different charge densities. It is shown that: i) the account of the flucton correlations leads to results considerably different from those obtained in the independent particle Glauber approach (IPGA); ii) in contrast to the case of IPGA the use of a more realistic density improves the agreement of CDPM-results with the experimental data.

Energy Technology Data Exchange (ETDEWEB)

The authors experimentally study the separate stages of the determination of iodine in thyroidin by the combustion method in a flask with oxygen. The monotypic, conventional procedures and the procedure of Kolii and Pakhomov were studied. With addition of potassium iodide, a sixfold amount (compared with the initial) of iodine is liberated. Further, the liberated iodine is titrated by sodium thiosulfate. The authors find the degree of influence of a high nitrogen content on the determination of iodine in organic compounds. The procedure developed for the quantitative determination of the iodine in thyroidin by the combustion method is simple, fairly rapid, and can be used for the reliable control of the quality of thyroidin preparations and its starting raw material.

Energy Technology Data Exchange (ETDEWEB)

The authors investigated phase equilibria in the system carbon dioxide-hexametapol. Vacuum-distilled solvent of ''pure'' grade was used. The solubility of CO/sub 2/ in hexametapol under pressures at various temperatures and the temperature dependence of the Henry's law coefficient is show. It is concluded that the solubility of carbon dioxide in hexametapol in the temperature and pressure ranges corresponding to the operating conditions of industrial equipment for removing CO/sub 2/ from gases conforms to the Krichevskii-II'inskaya equation. The experimental data can be used for equipment design.

International Nuclear Information System (INIS)

The single specimen unloading compliance technique has become the preferred method for evaluating J-integrals. It involves data acquisition and analysis using a computer. This paper describes in detail the development of a simple experimental system and related software that can be used in a laboratory equipped with a microcomputer and with access to a minicomputer. The effects of loading rate, test temperature, specimen geometry and material composition can be readily evaluated using this system. The results on a pressure vessel steel and an #alpha#-#beta# titanium alloy are discussed in Part II. (author).

Energy Technology Data Exchange (ETDEWEB)

Since 1976, the Nuclear Engineering Laboratory of the Technical Research Centre of Finland and Lappeenranta University of Technology have cooperated in the field of nuclear reactor thermal-hydraulics. During these years, a series of experimental facilities (REWET-I, -II, -III, VEERA) simulating pressurized water reactors (PWRs) have been built. The newest facility, PACTEL (Parallel Channel Test Loop), is an experimental out-of-pile facility designed to simulate the major components and system behaviour of a commercial PWR during postulated small and medium size break loss-of-coolant accidents (LOCAs), natural circulation and operational transients. A PACTEL natural circulation experiment has been carried out as an OECD/NEA international standard problem ISP 33. (2 refs., 3 figs., 2 tabs.).

Energy Technology Data Exchange (ETDEWEB)

This paper is concerned with the validation of the 3D deterministic neutral-particle transport theory code EVENT for shielding applications. The code is based on the finite element-spherical harmonics (FE-P{sub N}) method which has been extensively developed over the last decade. A general multi-group, anisotropic scattering formalism enables the code to address realistic steady state and time dependent, multi-dimensional coupled neutron/gamma radiation transport problems involving high scattering and deep penetration alike. The powerful geometrical flexibility and competitive computational effort makes the code an attractive tool for shielding applications. In recognition of this, EVENT is currently in the process of being adopted by the UK nuclear industry. The theory behind EVENT is described and its numerical implementation is outlined. Numerical results obtained by the code are compared with predictions of the Monte Carlo code MCBEND and also with the results ...

Energy Technology Data Exchange (ETDEWEB)

A spectral element method embodying Large Eddy Simulation based on Re- Normalization Group theory for simulating Sub Grid Scale viscosity was chosen for this work. This method is embodied in a computer code called NEKTON. NEKTON solves the unsteady, 2D or 3D,incompressible Navier Stokes equations by a spectral element method. The code was later extended to include the variable density and multiple reactive species effects at low Mach numbers, and to compute transport of large particles governed by inertia. Transport of small particles is computed by treating them as trace species. Code computations were performed for a number of test conditions typical of flow past a deep tube bank in a boiler. Results indicate qualitatively correct behavior. Predictions of deposition rates and deposit shape evolution also show correct qualitative behavior. These simulations are the first attempts to compute flow field results at realistic flow Reynolds numbers of the order of 10{sup 4}. Code ...

Energy Technology Data Exchange (ETDEWEB)

Some diagnostics at the National Ignition Facility (NIF), including the Gamma Reaction History (GRH) diagnostic, require multiple channels of data to achieve the required dynamic range. These channels need to be stitched together into a single time series, and they may have non-uniform and redundant time samples. We chose to apply the popular cubic smoothing spline technique to our stitching problem because we needed a general non-parametric method. We adapted one of the algorithms in the literature, by Hutchinson and deHoog, to our needs. The modified algorithm and the resulting code perform a cubic smoothing spline fit to multiple data channels with redundant time samples and missing data points. The data channels can have different, time-varying, zero-mean white noise characteristics. The method we employ automatically determines an optimal smoothing level by minimizing the Generalized Cross Validation (GCV) score. In order to automatically ...

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation of a humidification-dehumidification desalination (HDD) process using solar energy at the weather conditions of Suez City, Egypt, is presented. A test rig is designed and constructed to conduct this investigation under different environmental and operating conditions. The test rig consists of a solar water heater (concentrator solar collector type), solar air heater (flat plate solar collector type), humidifier tower and dehumidifier exchanger. Different variables are examined including the feed water flow rate, the air flow rate, the cooling water flow rate in the dehumidifier and the weather conditions. Comparisons between the experimental results and other published results are presented. It is found that the results of the developed mathematical model by the same authors are in good agreement with the experimental results. The tested results show that the productivity of the system is ...

Energy Technology Data Exchange (ETDEWEB)

In this work the authors study the stabilization point of a lifted, reacting jet of nitrogen diluted methane in co-flowing air. The jet flow is acoustically forced so as to organize the large scale vortical structures. The validation of the numerical results is possible through a concurrent experimental investigation of a similar planar jet. The use of an acoustically forced planar jet allows for significant savings by the restriction of the computation to two dimensions; the model is otherwise applicable in three dimensions. The authors based their study on the following parameters, which are derived from the experimental setup: a jet width of 1.16 cm, a mean jet velocity of 0.8 m/s, and a coflow velocity of 0.1 m/s. The acoustical forcing is studied at frequencies of 7.5 MHz and 90 MHz, which have been established experimentally as being characteristic of two broad behavioral modes. The authors ...

Energy Technology Data Exchange (ETDEWEB)

In this paper the authors present some final results from a research project focused on introducing automatic control to the operation of cupola iron furnaces. The main aim of this research is to improve the operational efficiency and performance of the cupola furnace, an important foundry process used to melt iron. Previous papers have described the development of appropriate control system architectures for the cupola. In this paper experimental data is used to calibrate the model, which is taken as a first-order multivariable system with time delay. Then relative gain analysis is used to select loop pairings to be used in a multiloop controller. The resulting controller pairs melt rate with blast volume, iron temperature with oxygen addition, and carbon composition with metal-to-coke ratio. Special (nonlinear) filters are used to compute melt rate from actual scale readings of the amount of iron produced and to smooth the temperature measurement. The temperature ...

International Nuclear Information System (INIS)

As a three-year joint university-industry effort, development of a generalized boiling transition analysis method has been started in 2002 aiming at enhanced capabilities of subchannel analysis for a wide variety of BWR-type fuel bundle geometry from ordinary BWR to tight lattice fuel bundles. For this purpose, five dominant factors affecting boiling transition phenomena have been identified on which our efforts of experimentation and numerical analyses are focused. In this report, as the first-year achievement, we will describe a master plan of the development and contents for experimental approaches to construct thermal-hydraulic databases. The databases will be utilized for the developments of constitutive equations to describe the basic characteristics of the elementary processes. The planned experiments are divided into two groups. One is air-water experiments at atmospheric pressure, and the other is steam-water experiments up to 1 MPa. ...

International Nuclear Information System (INIS)

RELAP5 (Reactor Excursion and Leak Analysis Program) is a system code developed at the Idaho National Environmental and Engineering Laboratory for thermal hydraulic analysis of nuclear reactors. The code RELAP5 is widely used for safety analysis studies of commercial nuclear power plants. However, recent released version of RELAP5/3.2 and over present significant capabilities for analysis of nuclear reactor research systems. As a contribution to the assessment of RELAP5/3.3 for research reactor safety analysis, experimental data from the University of Massachusetts Lowell Research Reactor UMLRR are used. The UMLRR is a 1 MW, light water moderated and cooled, graphite-reflected, open-pool type research reactor. This paper presents the development and the validation of a UMLRR-RELAP model using experimental data. For this purpose, a series of experiments were performed for benchmarking RELAP5 calculations for research reactor ...

Energy Technology Data Exchange (ETDEWEB)

Experimental and theoretical investigation on drying of a single coal particle in fluidized bed combustor is presented. Coal particle drying was considered via the moist shrinking core mechanism. The results of the drying test runs of low-rank Serbian coals were used for experimental verification of the model. The temperature of the coal particle center was measured, assuming that drying was completed when the temperature equalled 100{sup o}C. The influence of different parameters (thermal conductivity and specific heat capacity of coal, fluidized bed temperature, moisture content and superheating of steam) on drying time and temperature profile within the coal particle was analyzed by a parametric analysis. The experimentally obtained results confirmed that the moist shrinking core mechanism can be applied for the mathematical description of a coal particle drying, while dependence between drying time and coal particle ...

Energy Technology Data Exchange (ETDEWEB)

A large part of mechanical and durability characteristics of cement-based materials comes from the performances of the hydrated cement, cohesive matrix surrounding the granular skeleton. Experimental studies, in situ or in laboratory, associated to models, have notably enhanced knowledge on the cement material and led to adapted formulations to specific applications or particularly aggressive environments. Nevertheless, these models, developed for precise cases, do not permit to specifically conclude for other experimental conclusions. To extend its applicability domain, we propose a new evolutive approach, based on reactive transport expressed at the microstructure scale of the cement. In a general point of view, the evolution of the solid compounds of the cement matrix, by dissolutions or precipitations, during chemical aggressions can be related to the pore solution evolution, and this one relied to the ionic exchanges with the external ...

British Library Electronic Table of Contents (United Kingdom)

Two analytical methods were proposed in this research, coupled electro-thermal finite element (FE) analysis and thermal-mechanical FE analysis, to analyze the mechanical behavior of bonding wire of power module under cyclic power loads, and the International Electrotechnical Commission standard is adopted in conducting a power cycling test. The exterior temperature distribution was measured by an infrared thermometer. Moreover, the junction temperature is calculated from the given thermal impedance of the semiconductor chip, chip power loss, and case temperature. Subsequently, the simulated temperature distribution via electro-thermal FE analysis is compared with experimental results to validate the methodology used in the aforementioned analysis. The analysis shows compressive stress at t...

Energy Technology Data Exchange (ETDEWEB)

A new process for the removal of tar from biosyngas, OLGA (Oil and Gas Washer), is presented. This gas cleaning technology is based on physical principles and is designed to eliminate tar problems that relate to fouling and er pollution. The applied principles are confirmed by experimental validation. OLGA can be operated without suffering from harmful effects on important gasification characteristics as cold gas efficiency, gasifier simplicity, and feedstock flexibility. Some fundamental considerations in the development of OLGA are discussed. Amongst these is a different approach to the tar problem. This approach does not consider the total tar content as decisive in the evaluation of gas cleaning equipment. Instead, evaluation is focussed on whether tar properties as condensation behaviour and water solubility can still occur. A biosyngas free of tar should therefore be synonymous to a biosyngas that is free of tar related problems.

British Library Electronic Table of Contents (United Kingdom)

Eight selected sulfonamide drugs were investigated as inhibitors of heat shock protein 90 (Hsp90). The investigation included simulated docking experiments to fit the selected compounds within the binding pocket of Hsp90. The selected molecules were found to readily fit within the ATP-binding pocket of Hsp90 in low-energy poses. The sulfonamides torsemide, sulfathiazole, and sulfadiazine were found to inhibit the ATPase activity of Hsp90 with IC50 values of 1.0, 2.6, and 1.5 mM, respectively. Our results suggest that these well-established sulfonamides can be good leads for subsequent optimization into potent Hsp90 inhibitors.

Energy Technology Data Exchange (ETDEWEB)

A method has been developed to optimize the energy resolution of a horizontally focusing monochromator. The method consists of determining the optimum radius of curvature of the cylindrically bent monochromator crystal by minimizing the total diffracted X-ray flux measured through an X-ray absorption foil. When measured at an absorption edge a global minimum can be identified, which corresponds to the minimum energy band accepted along the entire length of the crystal. Experimental verification of this method has been validated by comparing X-ray fluorescent scans taken for a series of crystal curvatures and by directly measuring the X-ray beam profiles at the corresponding points. The actual optical configuration and asymmetric-cut parameter of the focusing monochromator on beamline X4C at the National Synchrotron Light Source are modeled and ray tracing simulations of the optical system are compared with direct beam profile measurements.

International Nuclear Information System (INIS)

A numerical analysis method for melting/solidification phenomena has been developed to evaluate a feasibility of several candidate techniques in the nuclear fuel cycle. Our method is based on the eXtended Finite Element Method (X-FEM) which has been used for moving boundary problems. Key technique of the X-FEM is to incorporate signed distance function into finite element interpolation to represent a discontinuous gradient of the temperature at a moving solid-liquid interface. Construction of the finite element equation, the technique of quadrature and the method to solve the equation are reported here. The numerical solutions of the one-dimensional Stefan problem, solidification in a two-dimensional square corner and melting of pure gallium are compared to the exact solutions or to the experimental data. Through these analyses, validity of the newly developed numerical analysis method has been demonstrated. (author)

International Nuclear Information System (INIS)

Up to now, P diffusion in Ge is modeled with an effective diffusivity involving at most a quadratic dependence with the free electron concentration (n). However, recent theoretical studies suggest the existence of a triply negatively charged state for the free vacancy in germanium and experimental data indicate that the E center (PV pair) in Ge has a double acceptor state. These two facts would be consistent with a diffusivity model involving a cubic dependence with n. In this paper the validity of this approach is checked for both pure thermal diffusion (intrinsic and extrinsic) and implanted phosphorus, using either our own experiments or other data available from the literature. Although some discrepancies still exist in some cases for the redistribution of implanted P, it is shown that the introduction of this cubic dependence significantly improves the overall agreement as compared with the usual model.

British Library Electronic Table of Contents (United Kingdom)

Considering the status of knowledge on corrosion and corrosion protection and especially the need for long term compatibility data of structural materials in HLM a set of experiments to generate reliable long term data was defined and performed. The long term corrosion behaviour of the two structural materials foreseen in ADS, 316L and T91, was investigated in the design relevant temperature field, i.e. from 300 to 550degreeC. The operational window of the two steels in this temperature range was identified and all oxidation data were used to develop and validate the models of oxide scale growth in PbBi. A mechanistic model capable to predict the oxidation rate applying some experimentally fitted parameters has been developed. This model assumes parabolic oxidation and might be used for de...

Science.gov (United States)

Digital libraries need more than just a retrieval based on keywords, which can be inefficient for some applications. Thus, a document retrieval based on content of the digitized image version of the document can be a more appropriated approach. This paper discusses the retrieval of document images by means of identifying a variety of elements present in the document's image body. We propose a new strategy to identify and combine features extracted from a document image. We also consider the task of constructing an optimized feature set to improve the retrieval performance and to validate our experiments on an assorted database. Experimental results show that the proposed segmentation together with a wisely feature combination increase the overall retrieval performance. Moreover the retrieved images demonstrate the generality and effectiveness of our approach for an efficient segmentation and classification of document images.

Energy Technology Data Exchange (ETDEWEB)

A one-dimensional thermal model is derived to describe the temperature field around a vertical borehole heat exchanger (BHEx) for a geothermal heat pump. The inlet and outlet pipe flows are modeled as one, and an effective heat capacity is added to model the heat storage in the fluid and pipes. Parameter estimation techniques are then used to estimate various parameters associated with the model, including the thermal conductivity of the soil and of the grout which fills the borehole and surrounds the u-tube. The model is validated using test data from an experimental rig containing sand with known thermal conductivity. The estimates of the sand thermal conductivity derived from the model are found to be in good agreement with independent measurements.

British Library Electronic Table of Contents (United Kingdom)

A detailed chemical kinetic reaction mechanism is developed for primary reference fuel mixtures of n-hexadecane and 2,2,4,4,6,8,8-heptamethyl nonane for diesel cetane ratings. The mechanisms are constructed using existing rules for reaction pathways and rate expressions developed previously for the primary reference fuels for gasoline octane ratings, n-heptane and iso-octane. These reaction mechanisms are validated by comparisons between computed and experimental results for shock tube ignition and for oxidation under jet-stirred reactor conditions. The combined kinetic reaction mechanism contains the submechanisms for the primary reference fuels for diesel cetane ratings and submechanisms for the primary reference fuels for gasoline octane ratings, all in one integrated large kinetic reac...

Energy Technology Data Exchange (ETDEWEB)

A comparative study of three methods for extracting solar cell parameters of the single-diode lumped-circuit model is presented, using experimental characteristics collected from two silicon cells over a range of illuminations and temperatures. The results show that the curve-fitting method can often give erroneous parameter values. The 5-point methods are found to be reliable and accurate in situations where the model is a good approximation of cell performance. The analytical 5-point method, however, has the added advantage of simplicity. It is also found that for the cell measured, the single diode model is valid at illuminations above one-half AM1 but gives non-physical parameter values at lower illumination.

Energy Technology Data Exchange (ETDEWEB)

The excitation function of ({alpha},{ital xn}) reactions on {sup 191}Ir (abundance 37.3%) and on {sup 193}Ir (abundance 62.7%) has been measured for the 17--55 MeV alpha-particle bombarding energy range. The stacked foil activation technique and {gamma}-ray spectroscopy were used to determine the cross sections. The experimental data were compared with calculated values obtained by means of a geometry-dependent hybrid model. The initial exciton number {ital n}{sub 0}=4 with {ital n}=2, {ital p}=2, and {ital h}=0 gives the best agreements with the presently measured results. To calculate the excitation function theoretically a computer code was used. This set of excitation functions provides a data basis for probing the validity of combined equilibrium and preequilibrium reaction models in a considerable energy range.

British Library Electronic Table of Contents (United Kingdom)

The rolls and stand deflections induced by rolling force lead to a significant decrease in the radius prediction accuracy of the ring product in the in-plane roll-bending of strip. To precisely predict the deflections and control the radius, a new analytical model is developed. Numerical implementation is presented to solve the theoretical rolling force, the deflections as well as the inherent force-deflection relationship considering the interactions of the strip workpiece, the rolls and the stand. A series of profile measurements of the formed ring parts are made to assess the accuracy of the predicted deflections. Different control approaches are used in the experiments to validate the radius control model. The experimental results show that the model is reliable to control the radii wi...

Energy Technology Data Exchange (ETDEWEB)

For Stage II of the European Dioxin Project the following objectives were set: - Amendment of existing emission data collected for most relevant emission sources in order to reduce uncertainties of emission estimates. Collecting first emission data from countries not yet performing dioxin emission measurement programs. Extending the inventory of dioxin emissions to ambient air produced in Stage I by a complementary study on emissions to land and water. Extending the regional scope of data collection to countries in Central Europe. The report of Stage II of the European Dioxin Project is presented in 3 Volumes. Volume 1 contains an overview on the background and approach of different activities carried out and on the results obtained. These results are put into a broader view regarding the dioxin reduction measures in Europe leading to conclusions and recommendation for future work. Volume 2 of the report contains a detailed presentation of the ...

International Nuclear Information System (INIS)

... v. 14(8) p. 624-625. azido compounds cadmium complexes potentiometry

International Nuclear Information System (INIS)

Full text: Based on experience with nuclear material confiscated in Hungary from illicit trafficking activities in the nineties it has been decided that traditional gamma-spectrometry should be complemented by destructive analytical techniques. The 17/1996 (I. 31.) Korm. Governmental Decree delegated the identification, categorization and characterization tasks to the Institute of Isotopes, Budapest. Routine gamma-spectrometric methods have been further developed aiming at the i) age (production date) determination of seized samples and complete (nondismountable) uranium-bearing items (such as fresh fuel bundles and fission chambers) by HRGS technique, ii) improvement of measurement accuracy and reliability. Starting in 2005 mass spectrometry (ICP-SFMS) and scanning electron microscopy have been implemented to characterize nuclear samples in more detail and to analyze environmental samples both for isotopic and elemental composition focusing on long-lived ...

Energy Technology Data Exchange (ETDEWEB)

Within the scope of the German reactor safety research the thermohydraulic computer code ATHLET which was developed for accident analyses of western nuclear power plants is more and more used for the accident analysis of VVER-plants particularly for VVER-440,V-213. The experiments with the HORUS-facilities and the analyses with the ATHLET-code have been realized at the Technical University Zittau/Goerlitz since 1991. The aim of the investigations was to improve and verify the condensation model particularly the correlations for the calculation of the heat transfer coefficients in the ATHLET-code for pure steam and steam-noncondensing gas mixtures in horizontal tubes. About 130 condensation experiments have been performed at the HORUS-II facility. The experiments have been carried out with pure steam as well as with noncondensing gas injections into the steam mass flow. The experimental simulations are characterized as accident simulation tests ...

International Nuclear Information System (INIS)

Chelating tendencies of several biologically important compounds viz. glycocyamine (GCN: N-amidino-aminoethanoic acid) taurine (TRN: 2-aminoethanesulphonic acid) and pyridoxal [PDL: 3-hydroxy-5-(hydroxymethyl)-2-methyl-pyridine-4-carbaldehyde] have been examined by pH-metric titration technique in their binary complex formation with copper(II) and uranyl(VI) ions. The work has further been extended to investigating the ternary complex formation involving 2.2'-bipyridine. 1,10-phenanthroline or nitrilotriacetic acid as a primary and TRN and PDL as secondary ligands. All the experiments were carried out at 25"0C and at an ionic strength of 0.1M (NaCl0_4) in aqueous or 50% (v/v) aqueous-ethanol medium according to the suitability of the experimental conditions. Stabilities of ternary complexes as compared to those of the corresponding binary complexes of the secondary ligands have also been discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

Experiments on aqueous TiO{sup 2} photocatalytic reaction characteristics of 4 nitrogen-containing and 12 aromatic organic compounds were carried out. Based on the values calculated for the distribution of ionic species and atomic charge, the characteristics of their photocatalytic decomposition were estimated. It was shown that the dependence of decomposition of the N-containing compounds were linearly proportional to their nitrogen atomic charge values, while that of the aromatic compounds were inversely proportional. The effects of aqueous pH, oxygen content and concentration on the TiO{sup 2} photocatalytic characteristics of EDTA-Cu(II) and EDTA-Fe(III) were experimentally investigated. All EDTA systems were decomposed better in the pH range of 2.5{approx}3.0 and with more dissolved oxygen. These results could be applied to a unit process for removal of organic impurities dissolved in a source water of the system water, and for treatment ...

International Nuclear Information System (INIS)

A thermodynamic model for predicting the distribution coefficients has been developed by taking into account the extraction mechanism and the chloride complexation when Sm, Eu, Gd, Tb, Dy and Ho for single component systems are extracted from acidic chloride solutions by di-2-ethylhexyl ester in kerosene, respectively. The model equation includes two constants, of which one corresponds to the apparent extraction equilibrium constant and the other is due to the variation of the activity coefficients of organic species. These values are determined from a few experimental data by the curve fitting method. Then, the distribution coefficients under untried calculations, Bromley's formulation is used to estimate the activity coefficients of aqueous species and the interaction parameters for some rare earth chlorides are reported in terms of morality and molarity using data from Spedding et al. According to the authors the validity of this method has ...

Energy Technology Data Exchange (ETDEWEB)

A numerical investigation of a humidification dehumidification desalination (HDD) process using solar energy is presented. The HDD system consists mainly of a concentrating solar water heating collector, flat plate solar air heating collector, humidifying tower and dehumidifying exchanger. Two separate circulating loops constitute the HDD system, the first for heating the feed water and the second for heating air. A mathematical model is developed, simulating the HDD system, to study the influence of the different system configurations, weather and operating conditions on the system productivity. The model validity is examined by comparing the theoretical and experimental results of the same authors. It is found that the results of the developed mathematical model are in good agreement with the experimental results and other published works. The results show also that the productivity of the unit is strongly influenced by ...

International Nuclear Information System (INIS)

During the phases of separation, treatment, conditioning and storage of radioactive waste, destructive and nondestructive methods for their characterization are needed. In order to satisfy this necessity, in the frame of the National Program of Research and Development, the 'Laboratory for characterization of spent nuclear fuel and high/medium level radioactive waste- LABORAD' was created. The purpose of the project was to accredit the analysis methods available in the laboratory, and also to develop new methods for the characterization of the radioactive waste. A special attention was paid to the high-level radioactive waste and spent nuclear fuel characterization that require special facilities for handling. These facilities (e.g. hot cells, remote handlers, transport container) are already available in our institute. Experimental results and performances obtained during validation of the methods are presented in this paper. The laboratory ...

International Nuclear Information System (INIS)

Many types of pipe whip restraints are installed to protect the structural components from the anticipated pipe whip phenomena of high energy lines in nuclear power plants. It is necessary to investigate these phenomena accurately in order to design the pipe whip restraints properly and/or to evaluate the acceptability of the pipe whip restraint design. Various research programs have been conducted in many countries to develop analytical methods and to verify the validity of the methods. In this study, various types of finite elements in ANSYS, the general purpose finite element computer grogram, was used to simulate the postulated pipe whips to obtain impact loads and the calculted results were compared with the specific experimental results from the sample pipe whip test for the U-chaped pipe whip restraints. Some calculational models, having the gap element or the spring element between the pipe whip restraint and the pipe line, give ...

Energy Technology Data Exchange (ETDEWEB)

The plasma plume generated by a new type of high energy Janitor known as the railplug, is examined. The railplug is a miniaturized railgun that has the potential for improving ignition characteristics of combustible mixtures in engines. The objective of the study is to gain an uderstanding of the characteristics of the plasma created by a transparent railplug, and to validate a multidimensional computer simulation of the plasma and shock fronts. The nature of the plume emitted by the railplug was examined for three levels of electrical energy while firing into air at a pressure of 1 atm. The computer model is to be used to predict trends in railplug performance for various railplug designs, energies, and ambient conditions. The velocity of the plasma movement inside a transparent railplug was measured, as well as the velocity of the plume ejected from the cavity. A shock is produced at the initiation point of the arc and propagates down the cavity, eventually ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The objective of this research project is to demonstrate sensing, communication, information and control technologies to achieve a seamless integration of multivendor distributed energy resource (DER) units at aggregation levels that meet individual user requirements for facility operations (residential, commercial, industrial, manufacturing, etc.) and further serve as resource options for electric and natural gas utilities. The fully demonstrated DER aggregation system with embodiment of communication and control technologies will lead to real-time, interactive, customer-managed service networks to achieve greater customer value. Work on this Advanced Communication and Control Project (ACCP) consists of a two-phase approach for an integrated demonstration of communication and control technologies to achieve a seamless integration of DER units to reach progressive levels of aggregated power output. Phase I involved design and proof-of-design, and Phase II involves ...

Energy Technology Data Exchange (ETDEWEB)

The quality of molecular dynamics (MD) simulations of proteins depends critically on the biomolecular force field that is used. Such force fields are defined by force-field parameter sets, which are generally determined and improved through calibration of properties of small molecules against experimental or theoretical data. By application to large molecules such as proteins, a new force-field parameter set can be validated. We report two 3.5 ns molecular dynamics simulations of hen egg white lysozyme in water applying the widely used GROMOS force-field parameter set 43A1 and a new set 45A3. The two MD ensembles are evaluated against NMR spectroscopic data NOE atom-atom distance bounds, {sup 3}J{sub NH{alpha}} and {sup 3}J{sub {alpha}}{sub {beta}} coupling constants, and {sup 1}5N relaxation data. It is shown that the two sets reproduce structural properties about equally well. The 45A3 ensemble fulfills the atom-atom distance bounds derived ...

Energy Technology Data Exchange (ETDEWEB)

During the first 18 months of this project, four experimental subtasks were to have begun but only one of these was to have been completed. Additionally, five modeling subtasks were scheduled to begin, four of which were to have been completed. We are on schedule for all but one of these subtasks. All four experimental tasks are progressing on schedule. Initial durability tests were completed. The conclusions drawn from this first round of durability tests are being used to design the next set of tests. Initial baseline engine data were acquired and showed that the engine selected for this task behaves as hoped. However, the dyno controller is inadequate. The engine will be moved to another dyno during the near future. The modeling tasks are also progressing well. A model for the dynamic response of the ignition circuit was developed and validated. Two technical papers resulting from this model were submitted for ...

Science.gov (United States)

... VALIDATING NETWORK SECURITY POLICIES VIA STATIC ANALYSIS OF ROUTER ACL CONFIGURATION by Eric Gregory Wen Wei Wong ...

Energy Technology Data Exchange (ETDEWEB)

The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.

British Library Electronic Table of Contents (United Kingdom)

The contribution of ear photosynthesis to grain filling in wheat (Triticum aestivum L.) is not well known. The main objective of this work was to evaluate this contribution through three different experimental approaches: (1) ear photosynthesis was reduced by removing awns or shading the ears (in combination with a defoliation treatment), (2) grain weight per ear was compared in an 'all shaded' crop versus plants where only the vegetative parts were shaded ('ear emerging'), and (3) ear photosynthesis was reduced with DCMU (3-(3,4-dichlorophenyl)-1,1-dimethylurea), a specific inhibitor of photosystem II. In field experiments in La Plata (Argentina), cultivars Klein Escudo and BioINTA 3000 were subjected to awn removal and ear shading treatments, with or without severe defoliation, and to 'a...

International Nuclear Information System (INIS)

This paper discusses how the U.S. Liquid Metal Reactor Development Program has been restructured to carry out R and D on advanced reactor technology. The program gives particular emphasis to improvements to reactor safety. The new directions are based on the technology of the integral fast reactor (IFR). Much of the basis for superior safety performance using IFR technology has been experimentally verified and aggressive programs continue in EBR-II and TREAT. Progress has been made in demonstrating both the metallic fuel and the new electrochemical processes of the IFR. The FFTF facility is converting to metallic fuel; however, FFTF also maintains a considerable U.S. program in oxide fuels. In addition, generic programs are continuing in steam generator testing, materials development, and with international cooperation, aqueous reprocessing.

British Library Electronic Table of Contents (United Kingdom)

Objective.The objective of this study was to use the newly synthesized poly(quaternary ammonium salt) (PQAS)-containing polyacid to formulate the light-curable glass-ionomer cements and study the effect of the PQAS on the compressive strength and antibacterial activity of the formed cements.Materials and methods.The functional QAS and their constructed PQAS were synthesized, characterized and formulated into the experimental high-strength cements. Compressive strength (CS) and Streptococcus mutans viability were used to evaluate the mechanical strength and antibacterial activity of the cements. Fuji II LC cement was used as control. The specimens were conditioned in distilled water at 37 degrees C for 24 h prior to testing. The effects of the substitute chain length, loading as well as gra...

International Nuclear Information System (INIS)

Background vibration in a CANDU plant can be used to determine the dynamic characteristics of major items of equipment, such as calandria, the fuelling machines and the primary heat transport pumps. These dynamic characteristics can then be used to verify the seismic response of the equipment which, at present, is based on theoretical models only. The feasibility and basic theory of this new approach (which uses accelerations measured at several points on a structure and does not require knowledge of the source of excitation) was established in Phase I of the study. This report is based on Phase II in which the methods of analysis developed in Phase I were improved and verified experimentally. A Fast Fourier Transform (FFT) algorithm was incorporated and an interactive curve fitting technique was developed to obtain the dynamic characteristics in the form of natural frequencies, mode shapes and damping ratios. The method is now available for ...

International Nuclear Information System (INIS)

Measurements of the statistical characteristics of channel wall static pressure fluctuations in parallel one-component boiling flow are reported. The measurements span a wide range of local subcooling and vapor volume fraction, and correspond to flow regimes ranging from highly subcooled bubbly to saturated slug-annular. Vapor volume fraction measurements at the pressure measurement station are also reported in conjunction with visual observation of the flow structure. Variation of static pressure fluctuation intensity and spectral content with local thermal-hydraulic condition is demonstrated. Finally, it is suggested that diagnosis of local two-phase flow regime on the basis of (i) statistical characteristics of the pressure data, and (ii) time trace of pressure signal, may be possible. 15 refs.

International Nuclear Information System (INIS)

Charge carrier profiles are measured for boron implanted into silicon (E = 30 keV, dose range 5 x 10"1"5 to 2 x 10"1"6 B/cm"2) after rapid isothermal annealing using halogen lamps. Maximum temperatures between 1000 and 1300 "0C and holding times at T/sub max/ of 5 and 20 s are used for the annealing treatment. In a few additional experiments flash lamp annealing at 1350 "0C (pulse duration 20 ms) is investigated. By comparison of the experimental profiles with computer simulations using the SUPREM II program transient enhanced diffusion of boron could be detected in all investigated cases. Maximum charge carrier concentrations above the equilibrium solubility of boron are observed and are discussed. (author).

Science.gov (United States)

Batch interaction experiments were performed under aerobic conditions to characterize the adsorption behavior and valence speciation of CoEDTA complexes (equimolar at 10{sup -5} mol/L) in a series of Pliocene subsurface sediments containing various amounts of Fe and Mn oxides. The experiments were performed in 0.003 mol/L Ca(ClO{sub 4}){sub 2} with a solids concentration of 500 g/L at variable pH (4-9) and at the natural pH of the sediments (pH = 8.3). Three of these subaerial sediments (Ringold 1, 2, 3) contained significant quantities of extractable Fe and Mn, while the fourth (Ringold 4) was virtually devoid of sesquioxide precipates. Microscopic and mineralogic analyses of the most heavily encrusted material (Ringold 2) showed that the oxides existed as intergrain cements and contained crystalline goethite and rancieite/todorokite. Adsorption on a synthetic analog sorbent (0.6 mass% ferrihydrite-coated sand) over a range in pH showed that, while both Co(II) ...

Energy Technology Data Exchange (ETDEWEB)

In technical combustors, flow and combustion processes inside the combustion chamber determine the design and also the safety of the plant. A modelling technique was developed at TU Dresden which comprises both numerical simulations and experimental data and thus achieves a high degree of transparency in its visualisation of the processes inside the combustion chambers under investigation. With the experience gained, numerical models of commercial simulation software (FLUENT, CFX) can be validated by measured values, and potential applications of the programs can be investigated. The first stage of experimental modelling consisted in isothermal (cold) modelling in consideration of flow-relevant similarity characteristics. In the reactive, non-isothermal models, the fuel/air ratio and temperature conditions inside the original combustion chamber were modelled as well. In order to obtain detailed data on the combustion ...

Energy Technology Data Exchange (ETDEWEB)

The performance of a geologic repository for high-level nuclear waste will be influenced to a large degree by thermohydrologic phenomena created by the emplacement of heat-generating radioactive waste. The importance of these phenomena is manifest in that they can greatly affect the movement of moisture and the resulting transport of radionuclides from the repository. Thus, these phenomena must be well understood prior to a definitive assessment of a potential repository site. An investigation has been undertaken along three separate avenues of analysis: (i) laboratory experiments, (ii) mathematical models, and (iii) similitude analysis. A summary of accomplishments to date is as follows. (1) A review of the literature on the theory of heat and mass transfer in partially saturated porous medium. (2) A development of the governing conservation and constitutive equations. (3) A development of a dimensionless form of the governing equations. (4) A numerical study of ...

Energy Technology Data Exchange (ETDEWEB)

In the Institute for Atomic Energy, Rikkyo University, just after the TRIGA-2 research reactor of 100 kW has attained the criticality, the cylindrical box for neutron radiography (NR) irradiation was made in the attached pool, and the research on NR was started in 1961. Thereafter in 1985, the vertical irradiation pipe was installed in the reactor tank, and the experiment for collecting the basic data was begun. In 1986, based on the obtained data, the NR irradiation facility on full scale was installed in No. 2 tangential horizontal experimental hole. As the main NR irradiation facilities, the vertical neutron irradiation pipe, the use of which is stopped now, the NR facility using the horizontal experimental hole (RUR/N2), the irradiation facility and ancillary facilities such as beam shutter, beam catcher and hoist are described. As the main equipments for NR, the imaging apparatuses of cooled type CCD, SIT and superhigh sensitivity, the ...

Science.gov (United States)

Flow structures and heat transfer at the liquid-liquid interface are investigated experimentally and analytically in the entrance region of a liquid metal-water stratified flow in a horizontal rectangular channel. The two-equation model and the mixing length mode, including a damping turbulent region near the interface, are used to obtain analytical results for pressure drop, position of the interface, and heat transmission coefficients across the interface. Analytical results are compared with experimental results. Conclusions are presented and include the following: (1) vertical position of the interface increases or decreases along the stream according to the fluid flow rate of both fluids, and then approaches a constant value in the fully developed region; (2) pressure drop increases along the stream from the minimum value at the inlet; and (3) heat transmission coefficients across the interface decrease in the entrance region to a minimum ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

In summary, a scaling analysis of a water-cooled Reactor Cavity Cooling System (RCCS) system was performed based on generic information on the RCCS design of PBMR. The analysis demonstrates that the water-cooled RCCS can be simulated at the ANL NSTF facility at a prototypic scale in the lateral direction and about half scale in the vertical direction. Because, by necessity, the scaling is based on a number of approximations, and because no analytical information is available on the performance of a reference water-cooled RCCS, the scaling analysis presented here needs to be 'validated' by analysis of the steady state and transient performance of a reference water-cooled RCCS design. The analysis of the RCCS performance by CFD and system codes presents a number of challenges including: strong 3-D effects in the cavity and the RCCS tubes; simulation of turbulence in flows characterized by natural circulation, high Rayleigh numbers and low Reynolds numbers; ...

Energy Technology Data Exchange (ETDEWEB)

(Materials and Methods) (I) VX/sub 2/ carcinoma was transplanted to the rabbit tibia, sup(99m)Tc-MDP was intravenously injected when bone destruction was radiologically seen. Preoperative scintigraphs, postoperative one of the resected tibia and fibra and scintigraphs of sliced tumor were compared with each other. Tissue fragments were collected from the sliced tumor, and RI was measured to compare concentration rates at different parts together with histological investigations. (II) Tetracycline was given to the rabbit of Experiment (I) to compare with the concentration of sup(99m)Tc-MDP. (III) Microautoradiography method was done on the experimental animals for investigation of the concentration of sup(99m)Tc-MDP. (Results) (I) Localization of sup(99m)Tc-MDP was increased at the sites of tumorous bone formation, of reactive bone formation at tumor edges, and of cartilage calcification, with little concentration at tumor cells or necrotic ...

UK PubMed Central (United Kingdom)

Some acylhydrazine derived ONO donor Schiff bases and their Co(II) and Ni(II) complexes have been prepared having the same metal ion (cation) but different anions. These synthesized metal(II)...Full Text Available

International Nuclear Information System (INIS)

This study deals with testing the capability of the code PARET to simulate natural convection cooling phenomena under different boundary conditions. In addition to applying and testing some new options related to simulation of the control rod movement and studying the reactivity effect of thermal expansion fuel elements. The experiments of the simple thermal hydraulic loop of Missouri university about natural cooling phenomena in two narrow paralled channels were used to validate the code. The study indicate good results regarding the distribution of coolant flux velocity and clad temperature. In particular the heat transfer coefficient of natural convection has been calculated in good agreement with the experiment. On the other hand, the core of MNSR reactor has been modelled to simulate the reactor dynamic behaviour under natural convection cooling conditions for different initial power level. The observed oscillation during the initial phase vanishes gradually ...

Energy Technology Data Exchange (ETDEWEB)

A brief review and assessment of field measurement programs that provide data for mixed layer diffusion research is presented. The majority of programs emphasize either the meteorological aspects of the mixed layer or plume characterization. Few programs are available that provide the complimentary blend of plume and appropriate meteorological measurements needed to adequately validate mixed layer diffusion theory. Three major U.S. EPA (Environmental Protection Agency) field programs that provide data bases for model development and validation of mixed layer diffusion processes are described and discussed in more detail. The Regional Air Pollution Study (RAPS) focused on measurements of surface and mixed layer turbulent transport processes in the urban environment. The Tennessee Plume Study (TPS) obtained a database with coincident measurement of boundary layer turbulent structure and plume dispersion for a large coal-fired power plant in ...

International Nuclear Information System (INIS)

A formalism for the dynamical treatment of the molecular orbitals of valence nucleons in nucleus-nucleus collisions is developed with the use of the coupled-reaction-channel (CRC) method. The Coriolis coupling effects as well as the finite mass effects of the nucleon are taken into account in this model, of rotating molecular orbitals, RMO. First, the validity of the concept is examined from the viewpoint of the multi-step processes in a standard CRC calculation for systems containing two identical [core] nuclei. The calculations show strong CRC effects particularly in the case where the mixing of different l-parity orbitals - called hybridization in atomic physics - occurs. Then, the RMO representation for active nucleons is applied to the same systems and compared to the CRC results. Its validity is investigated with respect to the radial motion (adiabaticity) and the rotation of the molecular axis (radial and rotational coupling). ...

Science.gov (United States)

Sandwich panels have a very high stiffness to weight ratio, which makes them particularly useful in the aerospace industry where carbon fibre reinforced plastics and lightweight honeycomb cores are being used in the construction of floor panels, fairings and intake barrel panels. In the latter case, the geometry of the panels can be considered doubly curved. This paper presents an introduction to an ongoing study investigating the dynamic response prediction of acoustically excited composite sandwich panels which have double curvature. The final objective is to assess and hopefully produce an up to date set of acoustic fatigue design guidelines for this type of structure. The free vibration of doubly curved composite honeycomb sandwich panels is investigated here, both experimentally and theoretically, the latter using a commerically available finite element package. The design and manufacture of three test panels is covered before presenting ...

Science.gov (United States)

In this paper we investigate the effects of surface mediation on the adsorption behavior of argon at different temperatures on homogeneous graphitized thermal carbon black and on heterogeneous nongraphitized carbon black surface. The grand canonical Monte Carlo (GCMC) simulation is used to study the adsorption, and its performance is tested against a number of experimental data on graphitized thermal carbon black (which is known to be highly homogeneous) that are available in the literature. The surface-mediation effect is shown to be essential in the correct description of the adsorption isotherm because without accounting for that effect the GCMC simulation results are always greater than the experimental data in the region where the monolayer is being completed. This is due to the overestimation of the fluid-fluid interaction between particles in the first layer close to the solid surface. It is the surface mediation that reduces this ...

Energy Technology Data Exchange (ETDEWEB)

Dual-fuel engines are modified diesel engines burning simultaneously two fuels inside the cylinder: a gaseous one, called the primary fuel and a liquid one, called the pilot fuel. The thermal efficiency of the dual-fuel engine and of the diesel engine are comparable; the level of emissions is lower compared to the diesel one. This article presents a new procedure for the combustion modeling in a LPG-diesel dual-fuel engine. The procedures deals with the ignition delay period and with the rate of heat release inside the cylinder. This procedure is validated using experimental data issued front a collaboration with the Indian Institute of Technology from Madras, India. The used engine is a single-cylinder one, air-cooled. The pilot fuel is direct injected inside the cylinder The engine was run at constant load and with different diesel substitutions, i.e. for different air to fuel ratios of the primary fuel-air mixture. The general error of the ...

Energy Technology Data Exchange (ETDEWEB)

Validation of nuclear power reactor signals is often performed by comparing signal prototypes with the actual reactor signals. The signal prototypes are often computed based on empirical data. The implementation of an estimation algorithm which can make predictions on limited data is an important issue. A new machine learning algorithm called support vector machines (SVMS) recently developed by Vladimir Vapnik and his coworkers enables a high level of generalization with finite high-dimensional data. The improved generalization in comparison with standard methods like neural networks is due mainly to the following characteristics of the method. The input data space is transformed into a high-dimensional feature space using a kernel function, and the learning problem is formulated as a convex quadratic programming problem with a unique solution. In this paper the authors have applied the SVM method for data-based state estimation in nuclear power reactors. In ...

British Library Electronic Table of Contents (United Kingdom)

Electrodeposition of tertiary alumina/yttria/carbon nanotube (Al2O3/Y2O3/CNT) nanocomposite by using pulsed current has been studied in this investigation. Coating process has been performed on nickel sulphate bath and nanostructure of obtained compound layer is examined with high precision figure analysis of SEM nanographs. The effects of process variables, i.e., Y2O3 concentration, treatment time, frequency and duty cycle, have been experimentally studied. Statistical methods are used to achieve the minimum of corrosion rate and average size of nanoparticles. Finally the contribution percentage of different effective factors is revealed and confirmation run shows the validity of obtained results. Also it has been revealed that by changing the size of nanoparticles, corrosion properties o...

British Library Electronic Table of Contents (United Kingdom)

Abstract MicroRNAs (miRNAs) play important roles in global gene regulation. Researchers in recombinant protein production have proposed miRNAs as biomarkers and cell engineering targets. However, miRNA expression remains understudied in Chinese Hamster Ovary cells, one of the most commonly used host cell systems for therapeutic protein production. To profile highly conserved miRNA expression, we used the miRCURY- miRNA array for screening miRNAs in CHO cells. The selection criteria for further miRNA profiling included positive hybridization signals and experimentally validated predicted regulatory targets. On the basis of screening, we selected 16 miRNAs for quantitative RT-PCR profiling. We profiled miR expression in parental CHO DG44 and CHO K1 cell lines as well as four recombinant DG44...

Energy Technology Data Exchange (ETDEWEB)

A model describes the effect of changes to the pore structure on the mechanical properties of semi-coke during coking. The gap tensile experiment makes it possible to determine the mechanical properties of the coke and semi-coke; a theoretical analysis is valid for the deformation of samples in the gap tensile test, by which the gap tensile strength of the coke can be determined, and by which a method for the simultaneous determination of the effective modulus of elasticity was developed. The effect of the pore structure on the mechanical properties is given in semi-empirical equations. The main point here is to check whether a pore in the coke can be regarded as a Griffith crack, and whether the interaction of pores can be neglected. A model which takes the pore distribution into account was also developed and tested. A model for the change of pore structure during coking, which includes the contraction of the semi-coke, and which presupposes a difference in ...

Energy Technology Data Exchange (ETDEWEB)

The two-phase heat-transfer and pressure-drop characteristics of offset-strip-fin heat-exchanger geometries are examined using both experimental and analytical modeling techniques. Newly-obtained boiling-flow heat-transfer data are presented for two large-scale offset fin geometries at low-to-moderate wall-superheat conditions. Data for which nucleate boiling appeared to be completely suppressed were analyzed together with similar results for other offset fin surfaces to study the effects of channel dimensions on the convective evaporation component of the local heat transfer coefficient. Although these data were found to be well correlated in terms of modified forms of the F and Martinelli parameters used in previous studies of round-tube flows, a single F-factor correlation valid for all combinations of fin and channel dimensions did not appear to exist. The two-phase pressure-drop characteristics of offset-fin surfaces were found to be much ...

Energy Technology Data Exchange (ETDEWEB)

Total thermal resistance of ground heat exchanger (GHE) is comprised of that of the soil and inside the borehole. The thermal resistance of soil can be calculated using the linear source theory and cylindrical source theory, while that inside the borehole is more complicated due to the integrated resistance of fluid convection, and the conduction through pipe and grout. Present study evaluates heat exchange rate per depth of GHE by calculating the total thermal resistance, and compares different methods to analyze their similarities and differences for engineering applications. The effects of seven separate factors, running time, shank spacing, depth of borehole, velocity in the pipe, thermal conductivity of grout, inlet temperature and soil type, on the thermal resistance and heat exchange rate are analyzed. Experimental data from several real geothermal heat pump (GHP) applications in Shanghai are used to validate the present calculations. ...

Energy Technology Data Exchange (ETDEWEB)

With using artificial neural networks (ANNs), an analytical study related to the heated length effect on critical heat flux (CHF) has been carried out to make an improvement of the CHF prediction accuracy based on local condition correlations or table. It has been carried out to suggest a feasible criterion of the threshold length-to-diameter (L/D) value in which heated length could affect CHF. And within the criterion, a L/D correction factor has been developed through conventional regression. In order to validate the developed L/D correction factor, CHF experiments for various heated lengths have been carried out under low and intermediate pressure conditions. The developed threshold L/D correlation provides a new feasible criterion of L/D threshold value. The developed correction factor gives a reasonable accuracy for the original database, showing the error of -2.18% for average and 27.75% for RMS, and promising results for new experimental ...

Energy Technology Data Exchange (ETDEWEB)

We developed a new systematic calibration procedure which was applied to the prediction of the diffusivity, the segregation, and transient enhanced diffusion (TED) of an indium impurity. The TED of the indium impurity was studied using four different experimental conditions. Although indium is susceptible to TED, rapid thermal annealing (RTA) is effective in suppressing the TED effect and maintaining a steep retrograde profile. Like boron impurities, the indium shows significant oxidation-enhanced diffusion in silicon and has segregation coefficients much less than 1 at the Si/SiO{sub 2} interface. In contrast to boron, the segregation coefficient of indium decreases as the temperature increases. The accuracy of the proposed procedure was validated by using secondary ion mass spectrometry (SIMS) data and by using the 0.13-{mu}m device characteristics, such as V{sub th} and I{sub dsat}, for which the differences between simulation and experiment ...

International Nuclear Information System (INIS)

To respond to an increase of social problems concerning orphan sources in Japan, a working group was formed in the Japan Health Physics Society. In this working group, we investigated how to prevent acute radiation hazard or social panic regarding orphan sources in scrap metal and detection system for orphan sources brought into scrap yards before recycle. For detection system in a scrap yard we conducted an experiment on detectability of monitoring instrument using a radiation source mixed in scrap metal on a truck. The result showed that it was not easy to detect even a high-level source if it was shielded by scrap metal. We also estimated detection limits for radioactive materials in scrap metal by calculation that was validated with experimental data. We summarized present status about orphan sources in Japan and proposed a categorization of orphan sources according to dose rates to deal with unknown sources in a scrap yard. Our report ...

UK PubMed Central (United Kingdom)

A structurally conserved element, the trigger loop, has been suggested to play a key role in substrate selection and catalysis of RNA polymerase II (pol II) transcription elongation. Recently resolved...Full Text Available

UK PubMed Central (United Kingdom)

DNA from the peripheral blood mononuclear cells of 17 different individuals infected with human T-cell lymphoma/leukemia virus type II (HTLV-II) was successfully amplified by the polymerase chain reaction...Full Text Available

Science.gov (United States)

Sida rhomboidea. Roxb leaf extract (SRLE) is being used by the populace of North-East India to alleviate symptoms of diabetes and obesity. We have previously reported its hypolipidemic and anti-diabetic properties. In this study, we report the effect of SRLE on (i) in vivo modulation of genes controlling high fat diet (HFD) induced obesity and (ii) in vitro 3T3L1 pre-adipocyte differentiation and leptin release. Supplementation with SRLE significantly prevented HFD induced increment in bodyweight, plasma lipids and leptin, visceral adiposity and adipocyte hypertrophy. Also, SRLE supplementation reduced food intake, down regulated PPAR?2, SREBP1c, FAS and LEP expressions and up-regulated CPT-1 in epididymal adipose tissue compared to obese mice. In vitro adipogenesis of 3T3L1 pre-adipocytes was significantly retarded in the presence of SRLE extract. Also decreased triglyceride accumulation, leptin release and glyceraldehyde-3-Phosphate dehydrogenase activity along ...

International Nuclear Information System (INIS)

This is the 1st revision of the INIS/ETDE Joint Thesaurus. It contains 20 953 valid descriptors and 8 600 forbidden terms. It was last updated in December 2003. The Joint Thesaurus contains the controlled terminology for indexing all information within the subject scope of both INIS (International Nuclear Information System) and ETDE (Energy Technology Data Exchange) information systems. The terminology is intended for use in subject description for input or retrieval of information in those systems. The thesaurus is a terminological control device used in translating from the natural language of documents, indexers or users into a more constrained system language It is also a controlled and dynamic vocabulary of semantically and generically related terms which covers a specific domain of knowledge. The domain of knowledge covered by this Thesaurus includes physics (in particular, plasma physics, atomic and molecular physics, and especially nuclear and high-energy ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work was to establish a new binary data base by compiling the activity coefficients of plutonium and uranium at oxidation state +IV to better account for media effects in the liquid-liquid extraction operations implemented to reprocess spent nuclear fuel. Chapter 1: first reviews the basic thermodynamic concepts before describing the issues involved in acquiring binary data for the tetravalent actinides. The difficulties arise from two characteristics of this type of electrolyte: its radioactive properties (high specific activity requiring nuclearization of the experimental instrumentation) and its physicochemical properties (strong hydrolysis). After defining the notion of fictive binary data, an approach based on the thermodynamic concept of simple solutions is described in which the activity coefficient of an aqueous phase constituent is dependent on two parameters: the water activity of the system and the total concentration of dissolved ...

UK PubMed Central (United Kingdom)

The in vivo photochemical activity of photosystem II was inferred from modulated chlorophyll fluorescence and photoacoustic measurements in intact leaves of several plant species (Lycopersicon...Full Text Available

UK PubMed Central (United Kingdom)

Woolfolk, C. A. (University of Washington, Seattle). Reduction of inorganic compounds with molecular hydrogen by Micrococcus lactilyticus. II. Stoichiometry with inorganic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This document describes payload control at LLNL to ensure that all shipments of CH-TRU waste in the TRUPACT-II (Transuranic Package Transporter-II) meet the requirements of the TRUPACT-II SARP (safety report for packaging). This document also provides specific instructions for the selection of authorized payloads once individual payload containers are qualified for transport. The physical assembly of the qualified payload and operating procedures for the use of the TRUPACT-II, including loading and unloading operations, are described in HWM Procedure No. 204, based on the information in the TRUPACT-II SARP. The LLNL TRAMPAC, along with the TRUPACT-II operating procedures contained in HWM Procedure No. 204, meet the documentation needs for the use of the TRUPACT-II at LLNL. Table 14-1 provides a summary of the LLNL waste generation and ...

Energy Technology Data Exchange (ETDEWEB)

Biosorption using activated sludge biomass (ASB) as a potentially sustainable technology for the treatment of wastewater containing different metal ions (Cd(II), Pb(II) and Zn(II)) was investigated. ASB metal uptake clearly competed with protons consumed by microbial biomass compared with control tests with non-activated sludge biomass. Biosorption tests confirmed maximum exchange between metal ions and protons at pH 2.0-4.5. It was revealed by the study that the amount of metal ions released from the biomass increased with biomass sludge concentration. The result showed that maximum absorption of metal ions was observed for Cd(II) at pH 3.5, Pb(II) at pH 4.0, and pH 4.5 for Zn(II) ions. The maximum absorption capacities of ASB for Cd(II), Pb(II) and Zn(II) were determined to be 59.3, 68.5 and 86.5%, ...

Energy Technology Data Exchange (ETDEWEB)

Planning is an important part of computational model verification and validation (V&V) and the requisite planning document is vital for effectively executing the plan. The document provides a means of communicating intent to the typically large group of people, from program management to analysts to test engineers, who must work together to complete the validation activities. This report provides guidelines for writing a validation plan. It describes the components of such a plan and includes important references and resources. While the initial target audience is the DART Full System Model teams in the nuclear weapons program, the guidelines are generally applicable to other modeling efforts. Our goal in writing this document is to provide a framework for consistency in validation plans across weapon systems, different types of models, and different scenarios. Specific details contained in any ...

International Nuclear Information System (INIS)

Full text: Semiconductor detectors coated with boron or lithium compounds have been studied for neutron detection for decades but, until recently, have been limited to thermal neutron detection efficiencies of less than 5%. We reported previously on development and simulation studies of perforated detectors whose perforations are filled with neutron-reactive material in order to produce higher detection efficiencies. Incorporation of bare and cadmium-backed detectors into battery-powered devices with low-power electronics enables us to produce compact personal neutron dosimeters that provide LED readout of counts, which can be related approximately to neutron dose. We report here on experimental studies with such compact devices; devices capable of direct readout in dose units are anticipated. The thermal and epithermal neutron flux densities from the tangential beam tube of the TRIGA Mark II reactor at Kansas State University were measured. ...

UK PubMed Central (United Kingdom)

The identification and validation of biomarkers for diagnosing Alzheimer's disease (AD) and other forms of dementia are increasingly important. To date, ELISA measurement of β-amyloid(1–42),...Full Text Available

International Nuclear Information System (INIS)

A new study on the pressure-induced phase transitions of TiO_2 has been performed using all-electron density-functional theory based computations with the projector augmented wave and the linearized augmented plane wave methods considering five experimentally observed structures. The static results yield a picture that is consistent with experiments, i.e., phase transitions with pressure are predicted as rutile #-># monoclinic baddeleyite (MI) #-># orthorhombic I (OI) #-># cotunnite (OII) on compression, and OII #-># OI #-># MI #-># columbite (TiO_2II) on decompression. The elasticities of these five polymorphs are compared. Except for the baddeleyite structure, which is considerably softer than the other polymorphs, all phases show a zero pressure bulk modulus in the range of 200-240 GPa, consistent with compression results and the single crystal elastic constant; on the basis of these results we can say that the cotunnite ...

Energy Technology Data Exchange (ETDEWEB)

An overview of the understanding of correlation between valence electron and the optical properties of binary (A{sup N}B{sup 8-N}) and ternary (A{sup N}B{sup 2+N}C{sub 2}{sup 7-N}) tetrahedral semiconductors is presented here. We have presented two expressions relating the dielectric constant and electronic polarizability for the transition metal chalcogenides and pnictides (A{sup II}B{sup VI} and A{sup III}B{sup V}) and chalcopyrites (A{sup I}B{sup III}C{sub 2}{sup VI} and A{sup II}B{sup IV}C{sub 2}{sup V}) with the product of valence electrons and nearest neighbour distance d (A). The dielectric constant and electronic polarizability of these solids exhibit a linear relationship when plotted on a log-log scale against the nearest neighbour distance d (A), but fall on different straight lines according to the valence electron product of the compounds. We have applied the proposed relation on these solids and found a better agreement with the ...

CERN Document Server

We use X-ray scattering and molecular simulations to investigate the structural properties of complexes of multivalent cationic lipids and DNA molecules. At low mole fraction of neutral lipids (NLs), $\\Phi_{\\rm NL}$, the complexes show dramatic DNA compaction down to essentially close packed DNA arrays with a DNA interaxial spacing $d_{\\rm DNA}=25\\AA$. A gradual increase in $\\Phi_{\\rm NL}$ does not lead to a continuous increase in $d_{\\rm DNA}$ as observed for DNA complexes of monovalent cationic lipids (CLs). Instead, distinct spacing regimes exist, with sharp transitions between them. Three packing states have been identified: (i) close packed, (ii) condensed, but not close packed, with $d_{\\rm DNA}=27-28\\AA$, and (iii) an expanded state, where $d_{\\rm DNA}$ increases gradually with $\\Phi_{\\rm NL}$. Based on our experimental and computational results, we conclude that the DNA condensation is mediated by the multivalent cationic ...

British Library Electronic Table of Contents (United Kingdom)

The alloying of steel surface with aluminum (Al) using Microsecond-pulsed Intense Electron Beams (MIEB-Al) was developed and optimized in order to be used for improving the corrosion resistance of the 316, 1.4970 and T91 steels, exposed to liquid Pb and Pb-Bi-eutectic. The procedure consists in two steps: (i) coating the steel surface with Al or an Al-containing alloy layer and (ii) melting the coating layer and the steel surface layer using intense pulsed electron beam. In order to cover the steel surface with an homogeneous and crack-free Al-alloyed layer, the following experimental conditions are required: Al coating thickness range 5-10mm, electron kinetic energy 120keV; pulse duration 30ms; energy density 40-45J/cm2; number of pulses 2-3. Using the mentioned procedure, the corrosion r...

International Nuclear Information System (INIS)

Liquid metal cooling for the first wall and blanket of a magnetic confinement fusion reactor has various advantages. However, it has the disadvantages of large magnetohydrodynamic pressure drops and heat transfer deterioration under a strong magnetic field. Thus, the present authors have proposed cooling with a helium-lithium annular mist flow as well as the cooling with a liquid metal boiling flow, and as fundamental studies, investigated the effect of a magnetic field on the flow characteristics and heat transfer of liquid metal two-phase systems since the 1970s. In the present paper we summarize the important findings obtained from our experimental studies for (i) an air-mercury stratified flow in a horizontal rectangular channel, (ii) a helium-lithium annular mist flow in a horizontal rectangular channel, (iii) the mercury pool boiling on a horizontal surface, and (iv) air-mercury upward flows in a vertical circular tube. Based on the ...

Science.gov (United States)

We have used a cell-free polymerase I transcription system derived from HeLa cells to study the regulation of human rRNA synthesis. Analysis of deletion mutants spanning the start site of transcription at nucleotide +1 indicates that the control region affecting initiation of human rRNA synthesis is contained within sequences from nucleotides -158 to +18. This promoter region can be subdivided into (i) a central segment of approximately 40 base pair that is required for transcription and (ii) flanking sequences that influence the efficiency of transcription in vitro. We have examined the in vitro transcriptional activity of the human extract under various conditions that are thought to modulate rRNA synthesis in vivo. Cell-free extracts prepared from HeLa cells infected with adenovirus 2 synthesize human rRNA at levels greatly decreased relative to uninfected cell extracts. By contrast, in vitro transcription of human rRNA is stimulated 2- to 3-fold by the addition ...

Energy Technology Data Exchange (ETDEWEB)

A class II atomistic force field with Lennard-Jones 6-9 nonbond interactions is used to investigate equations of state (EOS) for important high explosive detonation products N{sub 2} and H{sub 2}O in the temperature range 700-2500 K and pressure range 0.1-10 GPa. A standard 6th order parameter-mixing scheme is then employed to study a 2:1 (molar) H{sub 2}O:N{sub 2} mixture, to investigate in particular the possibility of phase-separation under detonation conditions. The simulations demonstrate several important results, including: (1) the accuracy of computed EOS for both N{sub 2} and H{sub 2}O over the entire range of temperature and pressure considered; (2) accurate mixing-demixing phase boundary as compared to experimental data; and (3) the departure of mixing free energy from that predicted by ideal mixing law. The results provide comparison and guidance to state-of-the-art chemical kinetic models.

CERN Document Server

Using a sample of 122 million Upsilon(3S) events recorded with the BaBar detector at the PEP-II asymmetric-energy e+e- collider at SLAC, we search for the h_b(1P) spin-singlet partner of the P-wave chi_b(1P) states in the sequential decay Upsilon(3S) --> pi0 h_b(1P), h_b(1P) --> gamma eta_b(1S). We observe an excess of events above background in the distribution of the recoil mass against the pi0 at mass 9902 +/- 4 (stat.) +/- 1 (syst.) MeV/c^2. The width of the observed signal is consistent with experimental resolution, and its significance is 3.0 sigma, including systematic uncertainties. We obtain the value (3.7 +/- 1.1 (stat.) +/- 0.7 (syst.))x 10^{-4} for the product branching fraction BF(Upsilon(3S) --> pi0 h_b) x BF(h_b --> gamma eta_b).

British Library Electronic Table of Contents (United Kingdom)

A novel method for the determination of metoclopramide (MCP) using electrogenerated chemiluminescence (ECL) is presented. A tris(2,2prime-bipyridyl)dichlororuthenium(II) (Ru(bpy)32+)-doped silica (RuDS) nanoparticle/perfluoinated ion-exchange resin (Nafion) with nanocomposite membrane modified glassy carbon electrode (GCE) is used. The Ru(bpy)32+ encapsulation interior of the silica nanoparticle maintains its electrochemical activities and also reduces Ru(bpy)32+ leaching from the silica matrix when immersed in water due to the electrostatic interaction. The analytical performance of this ECL sensor for MCP is shown in detail. Under optimal experimental conditions, it has good linearity in the concentration range from 2x10-8mol/L to 1x10-5mol/L (R=0.9989) with a detection limit of 7x10-9mo...

International Nuclear Information System (INIS)

The weldability and high temperature strength properties of tungsten-inert-gas (TIG) weldments of Hastelloy alloy XR were investigated by using two different heats of filler metals; the first (HXRF1) was designed on the basis of multiple regression analysis; the second (HXRF2) was the reference material. Bend tests, the FISCO cracking test and optical metallography were used to evaluate weldability. Tensile and creep tests were performed at 900deg C to evaluate high temperature strength properties. The results of weldability tests for both alloys showed good performance. The tensile properties of the weldments were remarkably improved in particular with respect to high temperature ductility. The creep rupture strength in the weldments made with alloy-designed HXRF1 was much higher than those of the Hastelloy alloy XR-II base metal with a higher B content. Furthermore, the creep properties were stable with respect to variations in welding conditions. Since the ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behavior of lanthanide oxides in molten alkaline chloride media is of great concern in pyrochemical processes for advanced nuclear fuel cycle. We have studied the solubilities of various lanthanide oxides in LiCl-KCl eutectic melt. In general, lanthanide oxides appeared to be insoluble/sparingly soluble in LiCl-KCl eutectic at 723 K. However, europium oxide exhibited an abnormal behavior in solubility and redox chemistry. The solubility of europium oxide was measured to be 1-2 order of magnitude higher than those of other lanthanide oxides. This abnormal solubility may be attributable to different electrochemical behavior of europium in the same experimental conditions. Most lanthanides ion exists as trivalent oxidation states. However, we observed divalent europium dissolved in LiCl-KCl molten salt by applying electron paramagnetic resonance(EPR) spectroscopy. (Figure 1) With the aid of this spectroscopic tool, it was found that stable ...

Science.gov (United States)

... It is recommended that the drawings be validated in accordance with NAVAIRINST 4333.10 and the data package, Appendix A, be used for ...

Science.gov (United States)

... During operations, the system successfully treated Phosgene (CG), chloropicrin (PS), a smoke-generating formulation based on hexachloroethane ...

International Nuclear Information System (INIS)

The Ranque-Hilsch tube is a particular type of vortex tube device. The flow enters the device tangentially near one end and exits from the open ends of the tube. The inlet air is of a uniform temperature throughout while the outputs are of different temperatures. One outlet is hotter and the other is colder than the inlet air. This device has no moving parts and does not require any additional power for its operation other than that supplied to the device to compress the inlet air. It has, however, not been widely used, mainly because of its low efficiency. In this paper, a simplified 2-dimensional computational fluid dynamics model for the flow in the vortex tube is developed using FLUENT. This model makes use of the assumption of axial symmetry throughout the entire flow domain. Compared to a three-dimensional computational solution, the simplified model requires significantly less computational time. This is important because the model is to be used for an optimization study. A ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this study concerns the use of numerical methods for the resolution of the Reynolds Averaged Navier Stokes equations adapted to the simulation of the cooling of the trailing edge of a stator in a high pressure turbine. These methods, based on the elsA solver developed at ONERA, use a four steps Runge Kutta time discretization scheme and a Jameson centered space discretization scheme. The scheme is applied through a finite volume approach on control volume centered on the cells of a multi-block structured mesh. Turbulence is simulated either through the algebraic Michel model, or through the one-transport-equation Spalart-Allmaras model, or through the two-transport-equations k 1, k {omega} and k {epsilon} models, and through ASM model. A simulation of the flow in a bidimensional stator, without cooling, is carried out. The cooling, which is realized with trailing edge slots, is then simulated on a bidimensional stator. Because the slot is represented by meshes overlapping ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to be able to describe transformations, occurring when solids and gases are in non isothermal and non isobaric conditions, with kinetic models. A methodology has been used. Two essential processes have to be taken into account: the germination and the growth. The germs are supposed to be formed (at constant temperature and pressure) in the grains surface with a constant velocity by surface unit, (gamma), called germination surface frequency (number of germs.m{sup -2}.s{sup -1}. The growth velocity is characterized by a growth surface reactivity, (phi) (in mol.m{sup -2}.s{sup -1}). With an appropriate transformation model, it is possible to obtain the variations of (gamma) and (phi) in terms of the temperature and pressure which are then used in the calculation of the velocity in non isothermal and non isobaric conditions. In order to validate the developed method, two reactions have been studied. For the first one, the kaolinite ...

Energy Technology Data Exchange (ETDEWEB)

''Intelligent Extruder'' described in this report is a software system and associated support services for monitoring and control of compounding extruders to improve material quality, reduce waste and energy use, with minimal addition of new sensors or changes to the factory floor system components. Emphasis is on process improvements to the mixing, melting and de-volatilization of base resins, fillers, pigments, fire retardants and other additives in the :finishing'' stage of high value added engineering polymer materials. While GE Plastics materials were used for experimental studies throughout the program, the concepts and principles are broadly applicable to other manufacturers materials. The project involved a joint collaboration among GE Global Research, GE Industrial Systems and Coperion Werner & Pleiderer, USA, a major manufacturer of compounding equipment. Scope of the program included development ...

International Nuclear Information System (INIS)

Fourier transform infrared absorption spectroscopy has been used for the determination of the line strengths of 41 CO and CO_2 absorption lines at temperatures between 295 and 1250 K. The CO vibrational-rotational lines were from the P branch of the fundamental absorption band (2150--1950 cm"-"1) while the CO_2 vibrational-rotational lines were from the far wing of the R branch of the #nu#_3 fundamental band (2395--2380 cm"-"1). The intensities of the lines were measured from absorption spectra recorded in a high-temperature gas cell containing known concentrations of CO/CO_2/N_2 gas mixtures at atmospheric pressure. Absorption spectra were recorded through the cell with the use of a moderate-resolution Fourier transform infrared spectrometer. The absorption spectra were mathematically corrected for distortions resulting from the finite resolution of the spectrometer and for peak overlap. Line strength measurements were made from the corrected peaks by using the Bouguer-Lambert law and ...

Energy Technology Data Exchange (ETDEWEB)

The PIUS reactor utilizes simplified, inherent, passive, or other innovative means to accomplish safety functions. Accordingly, the PIUS reactor is subject to the requirements of 10CFR52.47(b)(2)(i)(A). This regulation requires that the applicant adequately demonstrate the performance of each safety feature, interdependent effects among the safety features, and a sufficient data base on the safety features of the design to assess the analytical tools used for safety analysis. Los Alamos has assessed the quality and completeness of the existing and planned data bases used by Asea Brown Boveri to validate its safety analysis codes and other relevant data bases. Only a limited data base of separate effect and integral tests exist at present. This data base is not adequate to fulfill the requirements of 10CFR52.47(b)(2)(i)(A). Asea Brown Boveri has stated that it plans to conduct more separate effect and integral test programs. If appropriately designed and conducted, ...

International Nuclear Information System (INIS)

Based on the occurrence of a number of plant incidents during low power and shutdown operating conditions, the Nuclear Regulatory Commission (NRC) has initiated several programs to better quantify risk during these periods. One specific issue of interest is the loss of residual heat removal (RHR) under reduced coolant inventory conditions. This issue is also of interest in the Federal Republic of Germany and an experiment was performed in the integral PKL-3 experimental facility at Siemens-KWU to supply applicable data. Recently, an effort has been undertaken at the Idaho National Engineering Laboratory (INEL) to identify and analyze the important thermal-hydraulic phenomena in pressurized water reactors following loss of vital AC power and consequent loss of the RHR system during reduced inventory operation. The thermal-hydraulic response of a nuclear steam supply system (NSSS) with a closed reactor coolant system (RCS) to loss of residual heat removal cooling ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Melanoma (Skin)

Energy Technology Data Exchange (ETDEWEB)

This is a collection of photographs of the plant which is now almost completed.

Energy Technology Data Exchange (ETDEWEB)

PRESTO-II is a computer code developed to evaluate possible health effects from shallow land disposal of low level radioactive wastes. PRESTO-PREP is a data preprocessor that has been developed to expedite the formation of input data sets for PRESTO-II. PRESTO-PREP utilizes a library of nuclide and risk-specific data. Given an initial waste inventory, the code creates the radionuclide portion of the associated input data set for PRESTO-II. 2 references.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

PMID:10226312

Energy Technology Data Exchange (ETDEWEB)

Carbalkoxylation of vinyl electrophiles was investigated using platinum complexes. This reaction occurs in two steps: (a) carbonyl insertion of {sigma}-vinyl Pt(II) halides and (b) alcoholysis of vinylic acyl Pt(II) complexes. Alcoholysis of vinylic acyl Pt(II) triflate complexes is investigated kinetically. Vinylic acyl Pt(II) complexes were isolated and characterized. 51 refs., 5 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: A porous media solution PORFLO has been developed for the 3-dimensional two-phase flow by describing the process facility in Cartesian or cylindrical coordinates. The local porosity fraction is applied for distinguishing the fluid filled volumes from the solid structures. The solid structure contribute the two-phase flow through the wall friction, flow area and heat transfer. Optionally the solid structure may contain primary liquid of steam generators, steam in the higher temperature and pressure to be condensed or electrical heating power. By using these optional boundary conditions three different process facilities have been analysed. The thermohydraulic solution based on 5-equation approach, where the conservation equations are solved for the liquid and gas (vapour) mass, mixture momentum (giving the velocity only for the mixture), liquid and gas energy, is described shortly. In addition to that the principles modelling optional boundary ...

Energy Technology Data Exchange (ETDEWEB)

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the surety and reliability of the U.S. nuclear stockpile. The SSP uses past nuclear test data along with current and future non-nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering (D&E) programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of current facilities and programs along with new experimental facilities and computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computational resources to support the annual stockpile assessment ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: During calculations of SAR accidents and transients it is necessary to perform steam generator simulation. Best accuracy is 3D transient calculations presented in report. Main outcomes of work was next: 1. There was shown by analysis the applicability of code TRAC (Los-Alamos laboratory) for thermal - hydraulic calculations of horizontal steam generator PGV-1000M. Special nodalization scheme was developed for it purposes. 2. Validation and selection of thermal-hydraulic correlations for improvement of using the code at calculation PGV-1000M were performed. As result Labuntsov formula is recommended for horizontal SG. 3. Calculations of nominal mode operation of PGV-1000M for cross-verification with code STEG (Electrogorsk Research and Engineering Center EREC) during its verification were performed. Solution by TRAC was obtained for transient problem after stabilization time. 4. Development of dynamic SG model as conjugate problem ...

Energy Technology Data Exchange (ETDEWEB)

The subfornical organ is a major receptor area for one of the principal stimuli of thirst, the octapeptide, angiotensin II. In conscious water-sated rats, the authors examined the effects of intravenous infusion of angiotensin II on the rate of glucose utilization in the subfornical organ and in structures anatomically and functionally connected with it. Angiotensin II produced pressor and drinking responses and increased glucose utilization selectively in the subfornical organ and pituitary neural lobe and in no other brain structure. Treatment with the angiotensin II antagonist, sar1-leu8-angiotensin II, before intravenous administration of angiotensin II prevented metabolic stimulation of the subfornical organ and neural lobe. Captopril, an inhibitor of angiotensin-converting enzyme, reduced subfornical organ glucose metabolism to a level similar to that ...

Energy Technology Data Exchange (ETDEWEB)

The isotherms, kinetics and thermodynamics of Cd(II), Zn(II) and Pb(II) biosorption by Penicillium simplicissimum were investigated in a batch system. The effects of pH, initial metal ions concentration, biomass dose, contact time, temperature and co-ions on the biosorption were studied. Adsorption data were well described by both the Redlich-Peterson and Langmuir model. Chemical ion-exchange was found to be an important process based on free energy value from Dubini-Radushkevich isotherm for all metal ions. The results of the kinetic studies of all metal ions at different temperature showed that the rate of adsorption followed the pseudo second-order kinetics well. The thermodynamics constants {delta}G{sup o}, {delta}H{sup o} and {delta}S{sup o} of the adsorption process showed that biosorption of Cd(II), Zn(II) and Pb(II) ions on Penicillium simplicissimum ...

International Nuclear Information System (INIS)

When exposure-calibrated ionization chambers are used to calibrate megavoltage X-ray and electron beam therapy machines, the calibration factor can be divided into a chamber-dependent and a chamber-independent component. Until recently, only the chamber-independent part, which has been derived theoretically, has been used; the chamber-dependent component has been ignored. Recent experimental and theoretical considerations, however, have indicated that the dependent component must be taken into account and can affect the calibration by as much as 4%. The calibration can change due to (i) the thickness of the chamber wall, (ii) the chamber wall composition, i.e. whether the chamber is constructed of air-equivalent material, or tissue- or water-equivalent material, and (iii) the size of the chamber changing the displacement factor. Theoretical and experimental evidence indicates that the third factor varies from approximately ...

International Nuclear Information System (INIS)

Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the combustion threat has received less ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

ObjectivesThe updated Rome III criteria for pediatric functional gastrointestinal disorders (FGIDs) include new FGID categories and changes to the Rome II criteria...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

Aminopeptidase II, one of the two major aminopeptidases in the giant alga Chara australis, was partially purified. Its molecular weight was estimated to be about 80,000 by gel permeation...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The aim of this article was to investigate the interactions of metal cations in aqueous solutions with the biomass of the freshwater macroalga Vaucheria sp. This problem is important when elaborating new applications of biosorption, e.g. the production of mineral feed additives for livestock from the biomass of algae enriched with microelement ions. Potentiometric titration was applied as a quick and cheap screening test to search for new efficient biosorbents. It revealed a variety of functional groups capable of cation exchange on the macroalgal surface, including carboxyl, phosphate, hydroxyl or amino groups. Fourier transform infrared spectroscopy on natural and chromium-loaded Vaucheria sp. confirmed that carboxyl groups played a dominant role in the biosorption. The study also showed that Ca(II), Na(I), K(I), and Mg(II) ions were released from the biomass after biosorption of Cu(II), Mn(II), ...

UK PubMed Central (United Kingdom)

Rotazyme II, which is a shorter version of Rotazyme (less than 3 h), was compared with electron microscopy and Rotazyme for sensitivity and specificity on 229 human stool specimens. Compared with electron...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundPerfluorocarbons (PFC) are used to improve gas exchange in diseased lungs. PFC have been shown to affect various cell types. Thus, effects on alveolar type II (ATII) cells...Full Text Available

Science.gov (United States)

... Page 66 List of Figures Figure II.A.1 Simple Fuel Cell Model Page 8 ... Carbon Electrodes Figure II.A.1 Simple Fuel Cell Model Page 11. 9 ...

UK PubMed Central (United Kingdom)

Anaerobic reactions of Rhus vernicifera laccase and its type-2 copper-depleted derivatives with hexacyanoferrate(II) were investigated by absorption and e.s.r. spectroscopy. When native laccase was...Full Text Available