The photosynthetic activity of the green alga Scenedesmus quadricauda was investigated during synchronous growth in light/dark cycles. The rate of O2 evolution increased...Full Text Available
One of the key features of ANL's Integral Fast Reactor (IFR) concept is a close-coupled fuel cycle. The proposed fuel cycle is similar to that demonstrated over the first five to six years of operation of EBR-II, when a fuel cycle facility adjacent to EBR-II was operated to reprocess and refabricate rapidly fuel discharged from the EBR-II. Locating the IFR and its fuel cycle facility on the same site makes the IFR a self-contained system. Because the reactor fuel and the uranium blanket are metals, pyrometallurgical processes (shortned to ''pyroprocesses'') have been chosen. The objectives of the IFR processes for the reactor fuel and blanket materials are to (1) recover fissionable materials in high yield; (2) remove fission products adequately from the reactor fuel, e.g., a decontamination ...
This report summarizes the results of research conducted during the sixteen month continuation of a program to develop rechargeable zinc-air batteries for electric vehicles. The zinc-air technology under development incorporates a metal foam substrate for the zinc electrode, with flow of electrolyte through the foam during battery operation. In this ``soluble`` zinc electrode the zincate discharge product dissolves completely in the electrolyte stream. Cycle testing at Lawrence Berkeley Laboratory, where the electrode was invented, and at MATSI showed that this approach avoids the zinc electrode shape change phenomenon. Further, electrolyte flow has been shown to be necessary to achieve significant cycle life (> 25 cycles) in this open system. Without it, water loss through the oxygen electrode results in high-resistance failure of the cell. The Phase I program, which focused entirely on the zinc electrode, elucidated ...
This report summarizes the results of research conducted during the sixteen month continuation of a program to develop rechargeable zinc-air batteries for electric vehicles. The zinc-air technology under development incorporates a metal foam substrate for the zinc electrode, with flow of electrolyte through the foam during battery operation. In this soluble'' zinc electrode the zincate discharge product dissolves completely in the electrolyte stream. Cycle testing at Lawrence Berkeley Laboratory, where the electrode was invented, and at MATSI showed that this approach avoids the zinc electrode shape change phenomenon. Further, electrolyte flow has been shown to be necessary to achieve significant cycle life (> 25 cycles) in this open system. Without it, water loss through the oxygen electrode results in high-resistance failure of the cell. The Phase I program, which focused entirely on the zinc ...
The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.
The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.
We continue our discussion of the general bosonic prototype of the new orbifold-string theories of permutation-type. Supplementing the extended physical-state conditions of the previous paper, we construct here the extended Virasoro generators with cycle central charge $\\hat{c}_j(\\sigma)=26f_j(\\sigma)$, where $f_j(\\sigma)$ is the length of cycle $j$ in twisted sector $\\sigma$. We also find an equivalent, reduced formulation of each physical-state problem at reduced cycle central charge $c_j(\\sigma)=26$. These tools are used to begin the study of the target space-time dimension $\\hat{D}_j(\\sigma)$ of cycle $j$ in sector $\\sigma$, which is naturally defined as the number of zero modes (momenta) of each cycle. The general model-dependent formulae derived here will be used extensively in succeeding papers, but are evaluated in this paper only for the simplest case of the "pure" ...
Cu(II)-ATSM continues to be investigated, both in the laboratory and in the clinic, as a tumor hypoxia imaging agent. However, meaningful interpretation of these images requires a more complete understanding of the mechanism by which the tracer is trapped within the cell. Cu(II)-ATSM is a simple molecule and its biochemical interaction with cells is similarly simple, mainly based upon redox chemistry. Here we suggest that the trapping mechanism is biphasic. The first phase is a reduction/oxidation cycle involving thiols and molecular oxygen. This can be followed by interaction with proteins in the mitochondria leading to more permanent retention of the tracer. The uptake mechanism is complicated by this second step because of the changes in the cell resulting from hypoxia, such as an incre...
Objectives(i) Investigate the correlation between Antarctic sea-ice and equatorial sea-surface temperature anomalies in a realistically forced ocean model simulation of the last 50 years. (ii) Determine whether and how the enormous seasonal change in distribution of sea-ice modifies the seasonal cycle at the Equator. (iii) Determine the detailed pathways of wave propagation both in a historically-forced simulation and in response to realistic perturbations. (iv) Quantify the amplitude of the response i [continued...]DescriptionIt is well known that the equatorial ocean-atmosphere system plays a key role in global climate events such as the El Nino-Southern Oscillation (ENSO) phenomenon. There is now compelling evidence that changes in the Antarctic can strongly and quickly affect the equatorial ocean and the ENSO cycle. Observations demonstrate statistically significant correlations (teleconnections) between the Antarctic ...
The sulfur-iodine (SI) thermochemical cycle is one of the main candidate methods to produce hydrogen from non-fossil sources like nuclear (GEN IV reactor) or solar thermal power. A major issue for the successful implementation of the SI cycle is the selection of technically viable and economic materials for construction of process components, particularly heat exchangers. Challenging conditions are encountered in each of the three sections of the SI cycle due to the corrosive chemicals present, including sulfuric acid, iodine, hydroiodic acid, sulfur dioxide, hydrogen, oxygen, and others. In Section I, aqueous, non-aqueous (liquid iodine), and gaseous multi-component phases are present at about 120 {sup o}C and 0.7 MPa. Section II involves gaseous and aqueous phases of sulfuric acid, sulfur dioxide, and oxygen at up to about 830 {sup o}C and 3.6 MPa. In Section III , aqueous, non-aqueous, and gaseous ...
The low-cycle fatigue properties of the ferritic-martensitic steels MANET I and II and F82H-mod, have been investigated at a temperature of 200 C. The strain-controlled fatigue has been performed with strain ranges between 0,4% and 1,0% and at a strain rate of 8.10{sup -4} s{sup -1}. The steel F82H-mod, is characterised by a higher plastic strain amplitude compared to MANET I and II. Some of the specimens have beenirradiated with a 104 MeV {alpha}-particle beam. The homogeneous implantation of 400 appm He leads to a hardening of the material. At the beginning of the fatigue tests the stress response of the irradiatedspecimens is higher compared to the unirradiated specimens. In general, thematerial shows softening during fatigue. The softening of irradiated material, which is fatigue tested with a high total strain amplitude, is higher than that of the unirradiated material. The lifetime is reduced. For irradiated specimens ...
The failure rate of dashpots has been determined on the basis of the results of annually recurring function tests on hydraulic dashpots, in order to determine the effects of longer test cycles on the safety of systems GKN I and GKN II. The use of a calculation method made it possible to establish the number of defective dashpots in the system as a whole. A subsequent investigation illustrated the way in which this figure changes when the test interval is increased from four to ten years, and the effects of this on system safety. (orig.) [Deutsch] Zur Ermittlung der Auswirkungen verlaengerter Pruefzyklen auf die Sicherheit der Anlagen GKN I und GKN II wurde, basierend auf Ergebnisse der jaehrlichen Funktionspruefung an hydraulischen Stossbremsen, die Fehlerrate der Stossbremsen bestimmt. Mit Hilfe eines Berechnungsverfahrens konnte die Anzahl maengelbehafteter Stossbremsen in der Gesamtanlage bestimmt werden. Eine ...
We consider an admissible fibration $\\pi:X\\to\\mathbb{P}^1$ over a curve over a number field, of which the generic fiber $X_\\eta$ is geometrically rationally connected. We suppose that there exists a generalized Hilbertian subset $\\textsf{Hil}$ of $\\mathbb{P}^1$, such that the Brauer-Manin obstruction is the only obstruction to the Hasse principle (resp. to the weak approximation) for $X_\\theta(\\theta\\in \\textsf{Hil}).$ We prove that the Brauer-Manin obstruction is the only obstruction to the Hasse principle (resp. to the strong approximation) for zero-cycles of degree 1 on $X$ in the following cases: $(B_1)$ the index of the generic fibre $X_\\eta$ is equal to 1; $(B_2)$ all fibers are geometrically integral. Then, we obtain some similar results for certain fibrations over $\\mathbb{P}^n$. As a consequence, we obtain the following result: let $X$ be a smooth projective geometrically rationally connected variety over a number field $k$, if the Brauer-Manin ...
We present the initial results of an observational study into the variation of the dominant length-scale of quiet solar emission: supergranulation. This length-scale reflects the radiative energy in the plasma of the upper solar chromosphere and transition region at the magnetic network boundaries forming as a result of the relentless interaction of magnetic fields and convective motions of the Sun's interior. We demonstrate that a net difference of ~0.5Mm in the supergranular emission length-scale occurs when comparing observations cycle 22/23 and cycle 23/24 minima. This variation in scale is reproduced in the datasets of multiple space- and ground-based instruments and using different diagnostic measures. By means of extension, we consider the variation of the supergranular length-scale over multiple solar minima by analyzing a subset of the Mt Wilson Solar Observatory (MWO) Ca II K image record. The observations and ...
An electrolyte for high voltage lithium metal anode cells must simultaneously satisfy at least the following requirements; (i) high cycling efficiency on the lithium metal anode; (ii) higher oxidation potential than the charging voltage, and (iii) high specific conductivity. We have examined various electrolytes for lithium metal anode cells using a high voltage cathode, LiMn{sub 1.9}Co{sub 0.1}O{sub 4}. Of the electrolytes resistant to high voltage that we used, a system containing 60 to 90 vol.% of dimethyl carbonate (DMC) mixed with ethylene carbonate (EC) and 1.0 M lithium hexafluorophosphate (LiPF{sub 6}) provided the best cycling efficiency on a lithium metal anode, as well as a high specific conductivity around 10 mS cm{sup -1} at 20 C. (orig.)
One of the major limitations of the nickel (Ni) - yttria-stabilized zirconia (YSZ) anode support for solid oxide fuel cells (SOFC) is its low capability to withstand transients between reducing and oxidizing atmospheres (''RedOx'' cycle), owing to the Ni-to-NiO volume expansion. This work presents results on different anode supports fabricated by tape casting. Three compositions are prepared, as the outcome of a preceding design of experiment approach. The NiO proportion is 40, 50 and 60wt% of the anode composite. The anode support characteristics like shrinkage during sintering, in-situ conductivity at high temperature, electrochemical performance and tolerance against RedOx cycles have been measured. Performance up to 0.72Wcm^-^2 (0.62V, 800^oC) is recorded for the 60wt% NiO sample on sm...
The Computational Fluid Dynamics (CFD) Code KIVA II has been applied to model combustion pressure oscillations in the Indirect Injection Diesel Engine. These oscillations are attenuated and transmitted by the engine structure to the surroundings as noise. The computational model was used to evaluate changes in design and operating characteristics of an engine, and the effect of these on the intensity of gas pressure oscillation. The results in general corroborate the trends of published experimental measurements of combustion noise. A 40% increase in grid resolution showed minor changes in the magnitude of cylinder pressure oscillation and approximately 0.5{degree} crank angle phase advance in the oscillation cycle compared with the grid used for the results presented here. 18 refs., 18 figs.
High temperature deformation behaviour of an experimental Beta-titanium alloy Ti-10V has been studied in the temperature range 800 to 945 degree C by using the method of crosshead speed cycling. Although subgrain formation was observed but the alloy did not exhibit superplastic behaviour in the entire temperature range studied. A very large initial grain size and elongation of grains during the deformation are considered the main factors responsible for absence of superplastic behaviour. The activation energy values for regions II and III of the ln sigma vs. ln small epsilon plots are close to the lower of the two activation energy values proposed together to describe self diffusion in beta-phase suggesting that the rate controlling mechanism is that for lattice diffusion rather then grain boundary diffusion. (author)
A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat exergy efficiency is over 80%. (author)
A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat e...
Asynchronous Chinese hamster ovary (CHO) cells treated with conditioning hyperthermia (10 min at 45/sup 0/C) followed immediately by x irradiation with 4 Gy at room temperature display a decreased radiation response when either irradiated, or heated and irradiated again 24 h later. In addition, conditioning by 4 Gy of x radiation alone followed at 24 h by the combined heat and radiation treatment als resulted in a larger radiation D/sub 0/. Since the differential cell-cycle responses to heat- and x-ray-induced lethality are well established for CHO cells, the potential role of cell-cycle redistribution in the observed radiation desensitization was investigated by flow cytometry. At 24 h after the combined treatment, the fraction of the cells found in the G/sub 2/ + M portion of the DNA histograms was about three times that of the controls and there was a concomitant reduction in both the G/sub 1/ and S fractions. Similar observations were made ...
A few metal complexes of isatin-isonicotinoylhydrazone with Ni(II), Cr(III), Co(II), Cu(II), Zn(II) and Cd(II) have been prepared and characterized on the basis of elemental analyses, infrared and electronic spectra as well as "1H NMR spectra, conductivity and magnetic measurements. In view of the results obtained, it has been found that two molecules of isatin-isonicotinoylhydrazone are chelated to the central metal ion as bis-uninegative ONO tridentate ligand forming non-electrolytic octahedral metal complexes. (author)
Background and purpose: We evaluate the feasibility of concomitant and adjuvant docetaxel combined with three-dimensional conformal radiotherapy (3D-CRT) and androgen deprivation in high-risk prostate carcinomas. Methods: Fifty men with high-risk localized prostate cancer (16), locally advanced (28) or very high-risk prostate cancer (6) were included. Seventy Gy were delivered on prostate and seminal vesicles in 35 fractions, concurrently with weekly docetaxel (20 mg/m"2). Three weeks after the completion of 3D-CRT, docetaxel was given for 3 cycles (60 mg/m"2), every 3 weeks. Patients had to receive LHRH agonist during 3 years. Results: The intent to treat analysis shows that four patients out of 15 stopped prematurely the chemotherapy due to grade 3-4 acute toxicity. In the per protocol analysis, 46 patients completed a full-dose chemoradiation regimen representing 413 cycles: five patients experienced a grade 3 toxicity, and 15 patients ...
Platinum(II) complexes have been investigated in the hydration of alkynes. These catalysts offer improved regioselectivity over Hg(II) counterparts. 1 fig., 2 tabs.
The basic biology of the menstrual cycle is a complex, coordinated sequence of events involving the hypothalamus, anterior pituitary, ovary, and endometrium. The menstrual cycle with all its...Full Text Available
We present 14 years of contemporaneous photometric and spectroscopic observations of 28 solar analog stars, taken with the Tennessee State University Automatic Photometric Telescopes at Fairborn Observatory and the Solar-Stellar Spectrograph at Lowell Observatory. These are the best observed and most nearly Sun-like of the targets in our magnitude-limited (V #<=# 7.5) sample. The correlations between luminosity and activity reveal the expected inverse activity-brightness correlations for active stars. Strong direct correlations between activity and brightness are not prevalent for the less active solar age stars, but are precision limited. The Sun does not appear to have unusually low photometric variability when compared with the most Sun-like inactive solar analogs. We present evidence that the activity index R'_H_K is not a good discriminant of Maunder Minimum candidate stars. On the basis of a star that appears to have transitioned from a low-variability state to a ...
A class-V myosin, myosin V, one of 18 known classes of actin-based motor proteins, plays a role in transporting organelles within a cell. Unlike myosin-II, which functions as an assembly in the thick filaments of muscle, myosin V is a two-headed processive motor protein, which functions as a single molecule: myosin V performs many consecutive steps before it detaches from an actin filament accompanied by catalytic cycles of ATP (adenosine 5'-triphosphate) ase. The mechanism of such chemomechanical steps is explained by a 'Hand-over-hand model' in which two heads of myosin V alternately repeat single-headed and double-headed bindings with an actin filament. To investigate the binding state of myosin V at several key nucleotide states during ATP hydrolysis, we measured the mechanical properties of a single myosin V - actin complex by applying an external load with optical trap.
The electrochemical behavior of lanthanide oxides in molten alkaline chloride media is of great concern in pyrochemical processes for advanced nuclear fuel cycle. We have studied the solubilities of various lanthanide oxides in LiCl-KCl eutectic melt. In general, lanthanide oxides appeared to be insoluble/sparingly soluble in LiCl-KCl eutectic at 723 K. However, europium oxide exhibited an abnormal behavior in solubility and redox chemistry. The solubility of europium oxide was measured to be 1-2 order of magnitude higher than those of other lanthanide oxides. This abnormal solubility may be attributable to different electrochemical behavior of europium in the same experimental conditions. Most lanthanides ion exists as trivalent oxidation states. However, we observed divalent europium dissolved in LiCl-KCl molten salt by applying electron paramagnetic resonance(EPR) spectroscopy. (Figure 1) With the aid of this spectroscopic tool, it was found that stable ...
A new 500 kV one cycle electric circuit breaker with a mininum interrupting time of 12.5 m sec is described. The breaker, associated with a 1/4 cycle relay, insures a one cycle interruption. 5 refs.
The Army Reactor Area (ARA) II was constructed in the late 1950s as a test site for the Stationary Low Power Reactor No. 1 (SL-1). The SL-1 was a prototype power and heat source developed for use at remote military bases using a direct cycle, boiling water, natural circulation reactor designed to operate at a thermal power of 3,000 kW. The ARA II compound encompassed 3 acres and was comprised of (a) the SL-1 Reactor Building, (b) eight support facilities, (c) 50,000-gallon raw water storage tank, (d) electrical substation, (e) aboveground 1,400-gallon heating oil tank, (f) underground 1,000-gallon hazardous waste storage tank, and (g) belowground power, sewer, and water systems. The reactor building was a cylindrical, aboveground facility, 39 ft in diameter and 48 ft high. The lower portion of the building contained the reactor pressure vessel surrounded by gravel shielding. Above the pressure vessel, in the center portion ...
This paper reports on steam injection cycle which is similar to supplementary fired combined cycle, but for the utilized steam medium produced by HRSG, its temperature is higher and pressure is lower than in the combined cycle. In comparison with the thermodynamic advantage of the two cycles, a clear understanding of physical concept can be gotten simply by energy balance. The difference of total power output between them is subtraction of enthalpy difference of exhaust steam and feed water of HRSG in steam injection cycle from the rejected heat by water coolant of condenser in combined cycle, when using the identical gas turbine and the same amount of total fuel consumption. In general case, formulas and data are given to indicate this comparison by the ratio of steam mass flow supplied by HRSG of the two cycles. The analysis of Cheng ...
New tetradentate N(2)O(2) donor Schiff bases and their mononuclear Co(II), Ni(II), Cu(II), and Pd(II) complexes were synthesized and characterized extensively by IR, (1)H-, (13)C-NMR, mass, ESR, conductivity measurements, elemental and thermal analysis. Specifically the magnetic and electronic spectral measurements demonstrate the octahedral structures of cobalt(II), nickel(II) complexes and square planar geometries of copper(II), palladium(II) complexes. All the ligands and complexes were screened for their in vitro antibacterial activity against two gram-positive bacteria (Bacillus subtilis, Staphylococcus aureus) and two gram-negative bacteria (Escherichia coli, Klebsiella pneumonia). In this study, Pd(II) complexes exhibited potent antibacterial activity against B. subtilis, S. aureus whereas ...
Some acylhydrazine derived ONO donor Schiff bases and their Co(II) and Ni(II) complexes have been prepared having the same metal ion (cation) but different anions. These synthesized metal(II)...Full Text Available
A structurally conserved element, the trigger loop, has been suggested to play a key role in substrate selection and catalysis of RNA polymerase II (pol II) transcription elongation. Recently resolved...Full Text Available
The insulin/IGF-1 signaling (IIS) pathway is a conserved regulator of longevity, development, and metabolism. In Caenorhabditis elegans IIS involves activation of DAF-2 (insulin/IGF-1...Full Text Available
DNA from the peripheral blood mononuclear cells of 17 different individuals infected with human T-cell lymphoma/leukemia virus type II (HTLV-II) was successfully amplified by the polymerase chain reaction...Full Text Available
The results of this research centered on the experimental studies of a single superconducting persistent current qubit, the implementation of type-II algorithms using these qubits, and the proposal for adiabatic quantum computing using these qubits. The m...
The in vivo photochemical activity of photosystem II was inferred from modulated chlorophyll fluorescence and photoacoustic measurements in intact leaves of several plant species (Lycopersicon...Full Text Available
Woolfolk, C. A. (University of Washington, Seattle). Reduction of inorganic compounds with molecular hydrogen by Micrococcus lactilyticus. II. Stoichiometry with inorganic...Full Text Available
... and high-quality photospheric-phase Type II SN spectra to constrain core- collapse SN explosions, massive star evolution, and distances in the Universe ...
This document describes payload control at LLNL to ensure that all shipments of CH-TRU waste in the TRUPACT-II (Transuranic Package Transporter-II) meet the requirements of the TRUPACT-II SARP (safety report for packaging). This document also provides specific instructions for the selection of authorized payloads once individual payload containers are qualified for transport. The physical assembly of the qualified payload and operating procedures for the use of the TRUPACT-II, including loading and unloading operations, are described in HWM Procedure No. 204, based on the information in the TRUPACT-II SARP. The LLNL TRAMPAC, along with the TRUPACT-II operating procedures contained in HWM Procedure No. 204, meet the documentation needs for the use of the TRUPACT-II at LLNL. Table 14-1 provides a summary of the LLNL waste generation and ...
Biosorption using activated sludge biomass (ASB) as a potentially sustainable technology for the treatment of wastewater containing different metal ions (Cd(II), Pb(II) and Zn(II)) was investigated. ASB metal uptake clearly competed with protons consumed by microbial biomass compared with control tests with non-activated sludge biomass. Biosorption tests confirmed maximum exchange between metal ions and protons at pH 2.0-4.5. It was revealed by the study that the amount of metal ions released from the biomass increased with biomass sludge concentration. The result showed that maximum absorption of metal ions was observed for Cd(II) at pH 3.5, Pb(II) at pH 4.0, and pH 4.5 for Zn(II) ions. The maximum absorption capacities of ASB for Cd(II), Pb(II) and Zn(II) were determined to be 59.3, 68.5 and 86.5%, ...
The Heat Cycle Research Facility (HCRF) is an experimental binary-cycle facility used to investigate different concepts and/or components for generating electrical power from a geothermal resource. This report briefly desc
Metazoan life cycles can be complex in different ways. A number of diverse phenotypes and reproductive events can sequentially occur along the cycle, and at certain stages a variety of developmental...Full Text Available
A fuel cycle economic analysis was performed on four fuel cycles to provide a baseline for initial cost comparison using the Gen IV Economic Modeling Work Group G4 ECON spreadsheet model, Decision Programming Language software, the 2006 Advanced Fuel Cycle Cost Basis report, industry cost data, international papers, the nuclear power related cost study from MIT, Harvard, and the University of Chicago. The analysis developed and compared the fuel cycle cost component of the total cost of energy for a wide range of fuel cycles including: once through, thermal with fast recycle, continuous fast recycle, and thermal recycle.
The central features of the mechanical cycle that drives the contraction of muscle are two translational steps: the working stroke, whereby an attached myosin crossbridge moves relative to the actin...Full Text Available
Apart from the vulnerability implied by the START II treaty, it will bear the burden of the general political opposition to the Yeltsin administration. START II will be seen as part of an overall Yeltsin-Andrei Kozyrev foreign policy that is under fire for selling out Russian national interests in Yugoslavia, the Persian Gulf, and elsewhere. This article discusses public opinion concerning START II, the cost of its implementation, and the general purpose of the treaty.
The upgraded CDF II detector has collected first data during the initial operation of the Tevatron accelerator in Run II. The simulation of the CDF electromagnetic and hadronic central and upgraded plug (forward) calorimeter is based on the Gflash calorimeter parameterization package used within the GEANT based detector simulation of the Run II CDF detector. We present the results of tuning the central and plug calorimeter response to test beam data.
PRESTO-II is a computer code developed to evaluate possible health effects from shallow land disposal of low level radioactive wastes. PRESTO-PREP is a data preprocessor that has been developed to expedite the formation of input data sets for PRESTO-II. PRESTO-PREP utilizes a library of nuclide and risk-specific data. Given an initial waste inventory, the code creates the radionuclide portion of the associated input data set for PRESTO-II. 2 references.
The purpose of this paper is to describe the embedded computer systems approach taken at Experimental Breeder Reactor II (EBR-II) for non-safety related systems. The hardware and software structures for typical embedded systems are presented The embedded systems development process is described. Three examples are given which illustrate typical embedded computer applications in EBR-II.
Angiotensin II (Ang II) is a key proapoptotic factor in fibrotic tissue diseases. However, the mechanism of Ang-II-induced cell death in endothelial cells has not been previously elucidated....Full Text Available
Carbalkoxylation of vinyl electrophiles was investigated using platinum complexes. This reaction occurs in two steps: (a) carbonyl insertion of {sigma}-vinyl Pt(II) halides and (b) alcoholysis of vinylic acyl Pt(II) complexes. Alcoholysis of vinylic acyl Pt(II) triflate complexes is investigated kinetically. Vinylic acyl Pt(II) complexes were isolated and characterized. 51 refs., 5 figs., 6 tabs.
Studies were conducted of the bifunctional oxygen electrode. The development of a rechargeable metal-oxygen (air) cell has been hampered to a great extent by the lack of a stable and cost effective oxygen electrode capable of use during both charge and discharge. The first type of bifunctional electrode consists of two distinct catalytifc layers. The oxygen reduction catalyst layer containing a supported gold catalyst is in contact with a hydrophilic nickel layer in which evolution of oxygen takes place. Loadings of gold from 0.5 to 1.0 mg/cm/sup 2/ were investigated; carbon, graphite, metal, and spinel oxides were evaluated as substrates. The second part of the research effort was centered on developing a reversible oxygen electrode containing only one catalytic layer for both reduction and evolution of oxygen. The work was directed specifically to the study of perovskite type of oxides with the composition AA/sup 1/BO/sub 3/ where A is an element of the lanthanide series, A/sup 1/ is ...
Washboard (WB) modes (Smeulders P et al 1999 Plasma Phys. Control. Fusion 41 1303) are a very common edge instability regularly observed in the H-mode regime in JET. They are detected as (normally several) bands of continuously fluctuating magnetic activity rotating in the direction of the electron diamagnetic drift with typical frequencies in the range of 10-90 kHz. The time evolution of the WB mode frequency is found to follow qualitatively the evolution of the electron temperature measured near the pedestal top, probably due to the strong diamagnetic drift associated with the large pedestal gradients. Evidence for their involvement in the pedestal and ELM dynamics will be presented. Increasing WB mode amplitude is correlated with an increase in the time between consecutive type-I ELMs. In situations in which a sudden increase (decrease) of WB mode activity is observed, the build-up of the pedestal temperature (and, linked to this, also of the pedestal pressure) of the electrons is ...
Investigation and flow testing of the enlarged Phase I heat-extraction system at Fenton Hill continued throughout FY80. Temperature drawdown observed at that time indicated an effective fracture of approximately 40,000 to 60,000 m/sup 2/. In May 1980, hot dry rock (HDR) technology was used to produce electricity in an interface demonstration experiment at Fenton Hill. A 60-kVA binary-cycle electrical generator was installed in the Phase I surface system and heat from about 3 kg/s of geothermal fluid at 132/sup 0/C was used to boil Freon R-114, whose vapor drove a turboalternator. A Phase II system was designed and is now being constructed at Fenton Hill that should approach commercial requirements. Borehole EE-2, the injection well, was completed on May 12, 1980. It was drilled to a vertical depth of about 4500 m, where the rock temperature is approximately 320/sup 0/C. The production well, EE-3 had been drilled to a depth of 3044 m and ...
We have tested the suitability of a new single-aliquot regenerative-dose protocol for estimating the equivalent dose (D_e) in polymineral fine grains extracted from colluvia from various sites in Germany. First, we report the behaviour of three OSL signals: (i) blue-stimulated, (ii) infrared-stimulated luminescence, and (iii) blue-stimulated luminescence following infrared (IR) stimulation, using a near-UV (290-380 nm) detection window in each case. For these three signals, there is a significant change in sensitivity with regeneration cycle; this change can be compensated for using the response to a fixed test dose after each natural or regenerated measurement. The source of the three luminescence signals is then investigated using pulse-anneal and elevated-temperature experiments. Fading tests on laboratory-induced signals show that although the IR signals fade by up to 23% in 15 days at 100 deg. C, the post-IR blue signals are stable. The ...
The safety analysis checklist scope and the criteria of key parameters needed to be checked for Daya bay reload cycles are introduced. The INCORE code package was used for the safety evaluation of Daya bay unit 2 cycle 2. The method and the contents can not only be applicable for Daya Bay reload cycles but also for Qinshan 600 MW and Qinshan 300 MW reload cycles.
This paper presents an investigation into the feasibility and potential advantages of a small scale Miller cycle natural gas engine for applications such as domestic combined heat and power systems. The Miller cycle engine is compared to a standard Otto cycle engine using cycle analyses and multidimensional simulation, and basic engine design implications are discussed. It is found that the Miller cycle engine has a potential for improved fuel efficiency, but at the cost of a reduced power to weight ratio. A fuel efficiency advantage of 5{yields}10% compared to a standard Otto cycle engine appears possible, however it is stated that further investigations, in particular into the topic of engine friction, are required in order to validate the findings. (author)
This paper presents an investigation into the feasibility and potential advantages of a small scale Miller cycle natural gas engine for applications such as domestic combined heat and power systems. The Miller cycle engine is compared to a standard Otto cycle engine using cycle analyses and multidimensional simulation, and basic engine design implications are discussed. It is found that the Miller cycle engine has a potential for improved fuel efficiency, but at the cost of a reduced power to weight ratio. A fuel efficiency advantage of Formula Not Shown compared to a standard Otto cycle engine appears possible, however it is stated that further investigations, in particular into the topic of engine friction, are required in order to validate the findings.
Deteriorating air quality in urban areas is leading bus manufacturers to look for cleaner drives of urban buses. Various new systems are now available, but it is difficult to compare them and verify their effects without having a driving cycle accurately representing contemporary average urban bus use. The idealized form (engine cycle, passenger car cycle or different kW/tonnes ratio and traffic conditions) of existing driving cycles disqualifies them for the purpose. For this reason, it was decided to attempt the development of a new driving cycle for urban buses. To this end, measurements were carried out on buses in service in four major Dutch towns. The resulting data were combined to produce a reference cycle comprising all data relating to urban bus use. Statistical methods were then used to compare a large number of 15-20 minute ...
The subfornical organ is a major receptor area for one of the principal stimuli of thirst, the octapeptide, angiotensin II. In conscious water-sated rats, the authors examined the effects of intravenous infusion of angiotensin II on the rate of glucose utilization in the subfornical organ and in structures anatomically and functionally connected with it. Angiotensin II produced pressor and drinking responses and increased glucose utilization selectively in the subfornical organ and pituitary neural lobe and in no other brain structure. Treatment with the angiotensin II antagonist, sar1-leu8-angiotensin II, before intravenous administration of angiotensin II prevented metabolic stimulation of the subfornical organ and neural lobe. Captopril, an inhibitor of angiotensin-converting enzyme, reduced subfornical organ glucose metabolism to a level similar to that ...
Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the ...
The isotherms, kinetics and thermodynamics of Cd(II), Zn(II) and Pb(II) biosorption by Penicillium simplicissimum were investigated in a batch system. The effects of pH, initial metal ions concentration, biomass dose, contact time, temperature and co-ions on the biosorption were studied. Adsorption data were well described by both the Redlich-Peterson and Langmuir model. Chemical ion-exchange was found to be an important process based on free energy value from Dubini-Radushkevich isotherm for all metal ions. The results of the kinetic studies of all metal ions at different temperature showed that the rate of adsorption followed the pseudo second-order kinetics well. The thermodynamics constants {delta}G{sup o}, {delta}H{sup o} and {delta}S{sup o} of the adsorption process showed that biosorption of Cd(II), Zn(II) and Pb(II) ions on Penicillium simplicissimum ...
The Fast Flux Test Facility (FFTF) is a 400 MWt sodium-cooled fast reactor operated by Westinghouse Hanford Company for the US Department of Energy to conduct fuels and materials testing in support of the US Liquid Metal Fast Breeder Reactor programme. Early in 1982, the FFTF began its first 100 day irradiation cycle. Since that time the plant has operated very well, achieving a cycle capacity factor of 94 per cent in the most recent irradiation cycle. The authors describe the results achieved in the first three cycles of operation and carrying through to the fourth reactor cycle which began in January 1984. (author).
Kawasaki Heavy Industries, Ltd. has developed a gas turbine combined cycle and cogeneration plant computer aided engineering (CAE) system, which creates cycle heat balance automatically on given configurations of gas turbines, heat recovery boilers, steam turbines and auxiliaries. The system can predict the performance of the plant as a function of control set points, loads, process steam requirements and ambient conditions, which enables accurate and fast design of gas turbine combined cycle and cogeneration plants. (author)
The present article describes the features of the fully-fired combined cycles and the outline of the plant. Hitachi has optimized fully-fired combined cycle systems by executing a heat recovery type combined cycle. For the fully-fired combined cycles, it is possible to raise plant efficiency through the selection of adequate gas turbine types and cycles. It is possible to apply existing boiler facilities, fuel combustion systems, and stacks. It is possible to execute civil and architectural works on existing plants in-service as well as modification works during routine inspections. The NOx increment by gas turbine unit installations can be reduced by denitration plant modifications. Examples of the fully-fired combined cycles under planning are also introduced. Furthermore, the relational technique and operational characteristics are mentioned, as for ...
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency ...
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency ...
A unified model is presented for a class of combined energy systems, in which the systems mainly consist of a heat engine, a combustor and a counter-flow heat exchanger and the heat engine in the systems may have different thermodynamic cycle modes such as the Brayton cycle, Carnot cycle, Stirling cycle, Ericsson cycle, and so on. Not only the irreversibilities of the heat leak and finite-rate heat transfer but also the different cycle modes of the heat engine are considered in the model. On the basis of Newton's law, expressions for the overall efficiency and power output of the combined energy system with an irreversible Brayton cycle are derived. The maximum overall efficiency and power output and other relevant parameters are calculated. The general characteristic curves of the system are presented for some given parameters. ...
An exact cosmological solution of Einstein's equations which has time-dependent rotation is presented. The t-constant sections are of Bianchi type II. The source of this geometry is a fluid which has not been thermalized. (Author).
Exposure of albumin to Cu(II) (10-100 microM) and ascorbate (0.1-2 mM) results in extensive molecular modifications, indicated by decreased fluorescence and chain breaks. The rate of utilization of...Full Text Available
ObjectivesThe updated Rome III criteria for pediatric functional gastrointestinal disorders (FGIDs) include new FGID categories and changes to the Rome II criteria...Full Text Available
Interleukin 2 (IL-2) and B-cell growth factors I and II (BCGF I and BCGF II) are lymphokines produced by T cells that play a major role in T- and B-cell cooperation. Peripheral blood lymphocytes from...Full Text Available
In this article are presented main results on electric potential investigations in stellarator/torsatron TJ-II and tokamak T-10 in a comparable regimes of device operation.
Aminopeptidase II, one of the two major aminopeptidases in the giant alga Chara australis, was partially purified. Its molecular weight was estimated to be about 80,000 by gel permeation...Full Text Available
New palladium(II) and platinum(II) complexes of saccharinate (sac), trans-[Pd(py)"2(sac)"2] (1), cis-[Pt(py)"2(sac)"2] (2), trans-[Pd(3-acpy)"2(sac)"2] (3) and cis-[Pt(3-acpy)"2(sac)"2] (4) (py=pyridine and 3-acpy=3-acetylpyridine) have been synthesized. Elemental analysis, UV-Vis, IR, NMR and TG/DTA characterizations have been carried out. The structures of 1-4 were determined by X-ray diffraction. The palladium(II) and platinum(II) ions are coordinated by two N-bonded sac ligands, and two nitrogen atoms of py or 3-acpy, forming a distorted square-planar geometry. The palladium(II) complexes (1 and 3) are trans isomers, while the platinum(II) complexes (2 and 4) are cis isomers. The mononuclear species in the solid state are connected by weak intermolecular C-H...O hydrogen bonds, C-H...@...
BackgroundThe binding of peptide fragments of antigens to class II MHC is a crucial step in initiating a helper T cell immune response. The identification of such peptide epitopes...Full Text Available
The aim of this article was to investigate the interactions of metal cations in aqueous solutions with the biomass of the freshwater macroalga Vaucheria sp. This problem is important when elaborating new applications of biosorption, e.g. the production of mineral feed additives for livestock from the biomass of algae enriched with microelement ions. Potentiometric titration was applied as a quick and cheap screening test to search for new efficient biosorbents. It revealed a variety of functional groups capable of cation exchange on the macroalgal surface, including carboxyl, phosphate, hydroxyl or amino groups. Fourier transform infrared spectroscopy on natural and chromium-loaded Vaucheria sp. confirmed that carboxyl groups played a dominant role in the biosorption. The study also showed that Ca(II), Na(I), K(I), and Mg(II) ions were released from the biomass after biosorption of Cu(II), Mn(II), ...
BackgroundPromoter region plays an important role in determining where the transcription of a particular gene should be initiated. Computational prediction of eukaryotic Pol II promoter...Full Text Available
Rotazyme II, which is a shorter version of Rotazyme (less than 3 h), was compared with electron microscopy and Rotazyme for sensitivity and specificity on 229 human stool specimens. Compared with electron...Full Text Available
The biosorption of lead (II) and copper (II) ions, single component and binary systems, by dried P. putida was investigated in a batch system. The effects of initial pH, temperature, initial single and binary mixture concentrations on the biosorption kinetics and equilibrium uptake of each component, both single and binary mixtures were investigated. The bacterial biomass exhibited the highest single and binary lead (II) and copper (II) ions uptake capacity at 25 and 30 deg. C, respectively, the initial pH value of 5.5 and at the initial metal ions concentration of 100 mg dm{sup -3}. The Freundlich and Langmuir adsorption models were used for the mathematical description of the biosorption equilibrium and isotherm constants were evaluated at different temperatures. Adsorption data were well described by the Langmuir model, although they could be modeled by the Freundlich equation. The thermodynamics ...
BackgroundPerfluorocarbons (PFC) are used to improve gas exchange in diseased lungs. PFC have been shown to affect various cell types. Thus, effects on alveolar type II (ATII) cells...Full Text Available
ATP-binding cassette A3 (ABCA3) is a lipid transport protein required for synthesis and storage of pulmonary surfactant in type II cells in the alveoli. Abca3 was conditionally deleted...Full Text Available
Cytokinesis in animal and fungal cells utilizes a contractile actomyosin ring (AMR). However, how myosin II is targeted to the division site and promotes AMR assembly, and how the AMR coordinates with...Full Text Available
Anaerobic reactions of Rhus vernicifera laccase and its type-2 copper-depleted derivatives with hexacyanoferrate(II) were investigated by absorption and e.s.r. spectroscopy. When native laccase was...Full Text Available
Photobilirubin II, a stereoisomer of bilirubin, binds to human serum albumin at a single binding site (K = 2.2 x 10(6)M-1), presumably the high-affinity bilirubin-binding site. Binding in the secondary...Full Text Available
The identification of MHC class II restricted peptide epitopes is an important goal in immunological research. A number of computational tools have been developed for this purpose, but there is a lack...Full Text Available
ii) Flammability: (iii) A capacity to oxidise: (iv) Corrosiveness: (v) Toxicity (including chronic ...an explosion or fire: (d) For substances with corrosive properties: (i) To reduce the ...likelihood of any unintended corrosion:(ii) To control the adverse effects of any corrosion:
The US National Energy Policy of 2001 advocated the development of advanced fuel and fuel cycle technologies that are cleaner, more efficient, less waste-intensive, and more proliferation resistant. The need for advanced fuel development is emphasized in on-going DOE-supported programs, e.g., Global Nuclear Energy Initiative (GNEI), Advanced Fuel Cycle Initiative (AFCI), and GEN-IV Technology Development. The Directorates of Energy & Environment (E&E) and Chemistry & Material Sciences (C&MS) at Lawrence Livermore National Laboratory (LLNL) are interested in advanced fuel research and manufacturing using its multi-disciplinary capability and facilities to support a design concept of a small, secure, transportable, and autonomous reactor (SSTAR). The E&E and C&MS Directorates co-sponsored this Laboratory Directed Research & Development (LDRD) Project on Mono-Uranium Nitride Fuel Development for SSTAR ...
... Screening Adjudication Monitoring Applicants of Information Behavior II I Conducting Investigations ... Applicants of Information Behavior Conducting ...
Titanate nanotubes were hydrothermally synthesized and their adsorption performances for lead(II) ion removal were studied. The results showed that titanate nanotubes ruptured in the adsorption process resulting in two distinct adsorption stages, thus achieving a maximum adsorption capacity of 3.752mmolg^-^1 of lead(II). Furthermore, it was found that the regeneration of titanate nanotubes loaded with the lead(II) ions can be readily achieved using the saturated EDTA disodium salt aqueous solution, thereby avoiding the trouble of disposal of adsorbent. The adsorption mechanism was also discussed in detail.
The interaction between N-donor adsorbates such as ammonia and pyridine with Cu(II)-exchanged montmorillonite, beidellite, flourohectorite into smectite clays has been studied by electron spin resonance. Cu(II) cations exchanged into smectites coordinate five ammonia or pyridine molecules in beidellite, four ammonia of pyridine molecules in hydroxyhectorite. Thus, the Cu(II) cations bound to the interior surfaces of these smectite clays constitute strong Lewis acid sites. 26 refs., 7 figs., 1 tab.
An Otto cycle engine with internal and external irreversibilities of friction and heat leakage, in which the heat transfer between the working fluid and the environment obeys linear phenomenological heat transfer law [q ?? ?(T ?1)], is studied in this paper. The optimal piston motion trajectory for maximizing the work output per cycle is derived for the fixed total cycle time and fuel consumed per cycle. Optimal control theory is applied to determine the optimal piston trajectories for the cases of with and without piston acceleration constraint on each stroke and the optimal distribution of the total cycle time among the strokes. The optimal piston motion with acceleration constraint for each stroke consists of three segments, including initial maximum acceleration and final maximum decel...
Many aspects of cellular motility and mechanics are cyclic in nature such as the extension and retraction of lamellipodia or filopodia. Inherent to the cycles of extension and retraction that test the environment is the production of mechano-chemical signals that can alter long-term cell behavior, transcription patterns, and cell fate. We are just starting to define such cycles in several aspects of cell motility, including periodic contractions, integrin cycles of binding and release as well as the normal oscillations in motile activity. Cycles of local cell contraction and release are directly coupled to cycles of stressing and releasing extracellular contacts (matrix or cells) as well as cytoplasmic mechanotransducers. Stretching can alter external physical properties or sites exposed b...
We report the of the existence of RV Tauri stars in the Large Magellanic Cloud (LMC). This class of variable star has hitherto been unidentified in the Magellanic Clouds. In light and color curve behavior the RV Tauri stars appear to be an extension of the Type II Cepheids to longer periods. A single period-luminosity-color relationship is seen to describe both the Type II Cepheids and the RV Tauri stars in the LMC.
Incorporation of /sup 32/P from (gamma-32P)ATP into tyrosine residues of the insulin-like growth factor (IGF)-II receptor was observed in a Triton X-100-insoluble fraction of rat adipocyte plasma membranes. IGF-II receptor phosphorylation proceeded to a stoichiometry of approximately 0.5 mol of phosphate/IGF-II binding site after 10 min of incubation at 4 degrees C. A Km for ATP of 6 microM was calculated for this phosphorylation reaction. Addition of IGF-II caused an approximately 2-fold increase in tyrosine phosphorylation of the IGF-II receptor in this preparation. In contrast, phosphorylation of angiotensin II by the Triton X-100 washed membranes was not stimulated by IGF-II. Incubation of purified receptor immobilized on IGF-II agarose or of receptor-enriched low density microsomal membranes with (gamma-32P)ATP did ...
Fragrance mix II (FM II) is a relatively new screening marker for fragrance contact allergy. It was introduced in the patch test baseline series in Denmark in 2005 and contains six different fragrance chemicals commonly present in cosmetic products and which are known allergens.
Fatty acid biosynthesis is crucial for all living cells. In contrast to higher organisms, bacteria use a type II fatty acid synthase (FAS II) composed of a series of individual proteins, making...Full Text Available
The advantage of high-resolution sequence stratigraphy, which takes base-levels as reference, is that it can be applied to continental depositional basins controlled by multiple factors and can effectively improve the accuracy and resolution of sequential stratigraphic analysis. Moreover, the principles of base-level cycles are also suitable for analyzing sequential stratigraphy in continental coal-bearing basins because of their accuracy in forecasting distribution of coal measures. By taking the Dongsheng coalfield in the Ordos basin as an example, the extensive application of base-level cycles in exploration and exploitation of coal is analyzed. The result shows that the Yan'an formation in the Dongsheng area is a long-term base-level cycle which is bordered by nonconformities and made up of five mid-term cycles and 13 short-term cycles. The long-term ...
Purpose Cisplatin plus gemcitabine is a standard regimen for first-line treatment of advanced non-small-cell lung cancer (NSCLC). Phase II studies of pemetrexed plus platinum compounds have also shown activity in this setting. Patients and Methods This noninferiority, phase III, randomized study compared the overall survival between treatment arms using a fixed margin method (hazard ratio [HR] < 1.176) in 1,725 chemotherapy-naive patients with stage IIIB or IV NSCLC and an Eastern Cooperative Oncology Group performance status of 0 to 1. Patients received cisplatin 75 mg/m(2) on day 1 and gemcitabine 1,250 mg/m(2) on days 1 and 8 (n = 863) or cisplatin 75 mg/m(2) and pemetrexed 500 mg/m(2) on day 1 (n = 862) every 3 weeks for up to six cycles. Results Overall survival for cisplatin/pemetrexed was noninferior to cisplatin/ gemcitabine (median survival, 10.3 v 10.3 months, respectively; HR = 0.94; 95% CI, 0.84 to 1.05). Overall survival was ...
Measurements were completed on the solubility of cupric and cuprous oxides in liquid water and steam at controlled pH conditions from 25 to 400 C (77 to 752 F). The results of this study have been combined with those reported from this laboratory in two previous EPRI reports to provide a complete description of the solubility of these oxides and the speciation of copper dissolved in liquid water and steam as a function of oxidation state, temperature, pH, and in the case of steam, pressure. These constitute the first set of reliable data for cuprous oxide solubility over this range of conditions. For the more intensively studied CuO case, agreement was found between our results and those of previous studies of its solubility in steam, whereas only partial agreement was evident for its solubility in liquid water. For both oxides this disagreement often amounted to orders of magnitude. The solubility of cuprous oxide is somewhat lower than that of CuO at ambient conditions, except as ...
Vulnerability to xylem embolism by freeze-thaw cycles and water stress was quantified in ring-porous (Quercus gambelii Nutt.), diffuse-porous (Populus tremuloides Michx.,...Full Text Available
We show here sodium ion cycling between complex I from Klebsiella pneumoniae and the F1F0 ATP synthase from Ilyobacter tartaricus in a reconstituted...Full Text Available
Most genetic changes that promote tumorigenesis involve dysregulation of G1 cell cycle progression. A key regulatory site in G1 is a growth factor–dependent restriction point (R) where cells...Full Text Available
This paper presents part-load evaluation of a natural gas-fired chemical looping combustion (CLC) combined cycle with CO2 capture. The novel combined cycle employs an air-based gas turbine, a CO2-turbine and a steam turbine cycle. In this combined cycle, the CLC reactors replace combustion chamber of the gas turbine. The proposed combined cycle has a net plant efficiency of about 52.2% at full-load, including CO2 compression to 200 bar. The part-load evaluation shows that reducing the load down to 60% results in an efficiency drop of 2.6%-points. However, the plant shows better relative part-load efficiency compared to conventional combined cycles. The pressure in CLC-reduction and -oxidation reactors is balanced by airflow control, using a compressor equipped with variable guide vanes. A combination of control strategies is discussed for plant start-up and ...
This presentation describes a method for analyzing, quantifying, and minimizing the total cost of fossil, combined cycle, and pumped hydro power plant cycling operation. The method has been developed, refined, and applied during engineering studies at some 160 units in the United States and 8 units at the Irish Electric Supply Board (ESB) generating system. The basic premise of these studies was that utilities are underestimating the cost of cycling operation. The studies showed that the cost of cycling conventional boiler/turbine fossil power plants can range from between $2,500 and $500,000 per start-stop cycle. It was found that utilities typically estimate these costs by factors of 3 to 30 below actual costs and, thus, often significantly underestimate their true cycling costs. Knowledge of the actual, or total, cost of cycling will ...
During the last 15 years cycles with CO{sub 2} capture have been in focus, due to the growing concern over our climate. Often, a natural gas fired combined cycle with a chemical absorption plant for CO{sub 2} capture from the flue gases have been used as a reference in comparisons between cycles. Neither the integration of the steam production for regeneration of amines in the combined cycle nor the off-design behaviour of such a plant has been extensively studied before. In this paper, the integration of steam production for regeneration of the amines is modelled at design load and studied in off-design conditions for a combined cycle. Different ambient conditions and part-load strategies and their influence on the cycle performance are also examined. Of particular interest is a novel strategy with the possibility of longer life of gas turbine blading, with ...
The hair follicle cycle successively goes through the anagen, catagen, telogen, and latency phases, which correspond, respectively, to hair growth, arrest, shedding, and absence before a new anagen...Full Text Available
Microstructural evolution due to thermal effects was studied in micro solder joints (55 {+-} 5 {micro}m). The composition of the Sn/Pb solder studied was found to be hypereutectic with a tin content of 65--70 wt%.This was determined by Energy Dispersive X-ray analysis and confirmed with quantitative stereology. The quantitative stereological value of the surface-to-volume ratio was used to characterize and compare the coarsening during thermal cycling from 0--160 C to the coarsening during annealing at 160 C. The initial coarsening of the annealed samples was more rapid than the cycled samples, but tapered off as time to the one-half as expected. Because the substrates to which the solder was bonded have different thermal expansion coefficients, the cycled samples experienced a mechanical strain with thermal cycling. The low-strain cycled samples had a 2.8% strain imposed on the ...
The Fast Flux Test Facility (FFTF) was designed to test fast-reactor fuels and other nonfuel materials. In its 37 reactor cycles of operations, the FFTF reactor has performed very well and successfully completed all the irradiation testings with an operating efficiency factor as high as 98%. Since FFTF is an experimental reactor, its core loading changed from cycle to cycle. Depending on the number of test assemblies in the core and their location, the core loading can change significantly from an essentially homogeneous core loading to a relatively nonhomogeneous or even highly localized heterogeneous loading. Consequently, the core reload design and initial criticality analyses were required for each operating cycle. The zero power initial critical control rod bank height was predicted before each reactor startup. The initial critical prediction depends on the reactivity conditions at the end of the ...
The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) ...
SummaryFor mammalian somatic cells the importance of microtubule cytoskeleton integrity in interphase cell cycle progression is uncertain. The loss, diminishment, or stabilization...Full Text Available
In this paper we have proposed a novel gas turbine cycle with hydrogen-fueled chemical-looping combustion, and the system study on two hydrogen-fueled power plants, the new gas turbine cycle and an advanced gas turbine cycle with H{sub 2}/O{sub 2} combustion, has been investigated with the aid of exergy principle (EUD methodology). The hydrogen fueled chemical-looping combustion in the new gas turbine cycle consists of two successive reactions: hydrogen fuel is reacted with metal oxide (reduction of metal oxide), and then instead of air or pure oxygen, the reduced metal is successively oxidized by the saturated air. As a result, the new hydrogen-fueled gas turbine cycle has a breakthrough performance, with at least about 12 percentage-point higher efficiency compared to the gas turbine cycle with H{sub 2}/O{sub 2} combustion, and will be environmentally superior ...
Rocket-Based Combined-Cycle (RBCC) engines intended for missiles and/or space launch applications incorporate features of rocket propulsion systems operating in concert with airbreathing engine cycles. Performance evaluation of these types of engines, which are intended to operate from static sea level take-off to supersonic cruise or accerlerate to orbit, requires ground test capabilities which integrate rocket component testing with airbreathing engine testing. A combined cycle engine test facility has been constructed in the General Applied Science Laboratories, Inc. (GASL) Aeropropulsion Test Laboratory to meet this requirement. The facility was designed to support the development of an innovative combined cycle engine concept which features a rocket based ramjet combustor. The test requirements included the ability to conduct tests in which the propulsive force was generated by rocket only, the ...
Some acylhydrazine derived ONO donor Schiff bases and their Co(II) and Ni(II) complexes have been prepared having the same metal ion (cation) but different anions. These synthesized metal(II) complexes have been characterized on the basis of their elemental analyses, magnetic moment, molar conductance, and IR and electronic spectral data. All of the Schiff base ligands function as tridentates and the deprotonated enolic form is preferred for coordination. In order to evaluate the effect of anions on the bactericidal activity, these synthesized complexes, in comparison to the uncomplexed Schiff bases have been screened against bacterial species., Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa and the results are reported. PMID:18475936
High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723 K by using Eu{sub 2}O{sub 3} as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723 K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.
High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723 K by using Eu_2O_3 as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723 K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.
High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723K by using Eu2O3 as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.
We determined the chromosomal localization and structure of the gene encoding human type II inosine 5{prime}-monophosphate dehydrogenase (IMPDH, EC 1.1.1.205), an enzyme associated with cellular proliferation, malignant transformation, and differentiation. Using polymerase chain reaction (PCR) primers specific for type II IMPDH, we screened a panel of human-Chinese hamster cell somatic hybrids and a separate deletion panel of chromosome 3 hybrids and localized the gene to 3p21.1{yields}p24.2. Two overlapping yeast artificial chromosome clones containing the full gene for type II IMPDH were isolated and a physical map of 117 kb of human genomic DNA in this region of chromosome 3 was constructed. The gene for type II IMPDH was localized and oriented on this map and found to span no more than 12.5 kb.
In this study we compared various maturity dependent aromatic, steroid and triterpenoid hydrocarbon ratios in bitumens that are freely extractable from sedimentary rocks (Bitumen I) with those in second extracts that comprised hydrocarbons closely associated with the kerogen/mineral matrix (Bitumen II). Bitumen II was released through kerogen isolation and demineralisation using HCl and HF/H3BO3. The samples studied, although of similar age, come from different localities. They represent a range of facies and two kerogen types (II and III), and all were deposited under marine conditions. The results show that the more stable b isomers of methylnaphthalene (MN) and methylphenanthrene (MP) are relatively more abundant in Bitumen II. The difference between the methylnaphthalene ratio (MNR) of...
An experimental study was conducted to determine the effects of ply thickness in composite laminates on thermally induced cracking and changes in the coefficient of thermal expansion (CTE). After a few thermal cycles, laminates with thick-plies cracked, resulting in large changes in CTE. CTE`s of the thin-ply laminates were unaffected by microcracking during the first 500 thermal cycles, whereas, the CTE`s of the thick-ply laminates changed significantly. After about 1500 cycles, microdamage had also reduced the CTE of the thin-ply laminates to a value of about half of their initial value.
For the development of a rechargeable zinc/air battery, La{sub 0.6}Ca{sub 0.4}CoO{sub 3}-catalyzed (perovskite) bifunctional oxygen electrodes and pasted zinc electrodes were prepared and tested in monopolar zinc/air cells. The cells were cycled in moderately alkaline electrolyte. The maximum power as well as the cycle life of the cells were investigated. Up to 450 cycles could be reached, and attractive specific energies and powers were obtained. (author) 3 figs., 4 refs.
In this study, the biosorption of Cd(II), Ni(II) and Pb(II) on Aspergillus niger in a batch system was investigated, and optimal condition determined by means of central composite design (CCD) under response surface methodology (RSM). Biomass inactivated by heat and pretreated by alkali solution was used in the determination of optimal conditions. The effect of initial solution pH, biomass dose and initial ion concentration on the removal efficiency of metal ions by A. niger was optimized using a design of experiment (DOE) method. Experimental results indicated that the optimal conditions for biosorption were 5.22 g/L, 89.93 mg/L and 6.01 for biomass dose, initial ion concentration and solution pH, respectively. Enhancement of metal biosorption capacity of the dried biomass by pretreatment with sodium hydroxide was observed. Maximal removal efficiencies for Cd(II), Ni(III) and ...
The radiation reduction of bis(1-ethylimidazole)tartratoplatinum(II) (EITPt(II)) complexes in methanol-water solution have been examined. The yields of Pt(I) depend on the presence of O{sub 2} in solutions as well as the dose applied. The rate constants of e{sub s}{sup -} scavenging by EITPt(II) and cis(diammine-1,1-cyclobutanedicarboxylato) platinum(II) (CBDCAPt(II)) have been determined by pulse radiolysis to be equal to 5.4 x 10{sup 9} and 6.4 x 10{sup 9} M{sup -1} s{sup -1}, respectively. The efficiencies of e{sub t}{sup -} scavenging by EITPt(II) and the rate of e{sub t}{sup -} photobleaching have also been determined in LiCl : H{sub 2}O : CH{sub 3}OH and MgCl{sub 2} : H{sub 2}O : CH{sub 3}OH glasses, respectively. (author).
The cell cycle-regulatory transcription factor E2F-1 is regulated by interactions with proteins such as the retinoblastoma gene product and by cell cycle-dependent alterations in E2F-1 mRNA abundance....Full Text Available
The possibility of having properly designed multinational fuel cycle agreements which would contribute to public acceptance of nuclear energy are explored. The advantages of existing international cooperation in the field of uranium enrichment and nuclear waste disposal and reprocessing are discussed. The possible forms of multinational co-operation under an international organisation, committed the non-proliferation and operating under international law and covering storage facilities, security of raw materials and the nuclear fuel cycle are summarised in model form. (U.K.).
A 5 V glassy carbon capacitor stack was built consisting of four bipolar and two end-plate electrodes. More than 100,000 charging/discharging cycles were applied to test the stability of the double-layer capacitor. Low and high frequency resistances were measured as a function of the number of cycles. (author) 2 figs., 1 ref.
The fuel management study on 18-months fuel cycle project is introduced for Daya Bay Nuclear Power Station. Station from the selection of the objective of fuel management for 18-months cycle, the method used and the analysis done are explained in detail to reach the final loading pattern chosen
The state of chromatin during the cell cycle was examined using synchronized cultures of CHO hamster cells. Results support Mazia's dynamic chromosome cycle model and indicate that DNA-interactive chemotherapeutic agents elicit different types of kinetic responses in treated cells, suggesting a degree of specificity of interaction between various alkylating and intercalating agents and the genome. Effects of sarkosyl crystals, heparin, and chemotherapeutic agents, neocarzinostatin and adriamycin, on chromation are discussed. (HLW)
We propose a dynamical model for business cycle based on an optimal DI model. In the model there exists a conserved quantity, which corresponds to the total energy in a dynamical system. We found that the business cycle with the period 6 or 7 years is nicely reproduced, since the model predicts a periodic motion in the conservative system.
Laser-Doppler anemometry was used to investigate mean flow and turbulence fields in a direct injection diesel engine, motored at speeds of 1500, 2250 and 3000 rev/min. Both cycle-resolved and ensemble-averaged measurements were made in the upper part of the cylinder during the inlet and compression strokes. The cycle-resolved measurements in the inlet stroke are discussed in this paper.
18-Months cycle reload design verifications of Daya Bay NPS is briefly described. It was attempted giving the description of analysis scope and key technology for a nuclear power plant which will be changed fuel management strategy from one year to 18-months cycle
Biomass is one of the main natural resources in Sweden. The present low-CO{sub 2} emission characteristics of the Swedish electricity production system (hydro and nuclear) can be retained only by expansion of biofuel applications for energy purposes. Domestic Swedish biomass resources are vast and renewable, but not infinite. They must be utilized as efficiently as possible, in order to make sure that they meet the conditions for sustainability in the future. Application of efficient power generation cycles at low costs is essential for meeting this challenge. This applies also to municipal solid waste incineration with energy extraction, which should be preferred to its dumping in landfills. Hybrid dual-fuel combined cycle units are a simple and affordable way to increase the electric efficiency of biofuel energy utilization, without big investments, uncertainties or loss of reliability arising from complicated technologies. Configurations of ...
Many sunspot cycles are double peaked. In 1967 Gnevyshev suggested that actually all cycles have two peaks generated by different physical mechanisms, but sometimes the gap between them is too short for the maxima to be distinguished in indices of the total sunspot activity. Here we show that indeed all cycles have two peaks easily identified in sunspot activity in different latitudinal bands. We study the double peaks in the last 12 sunspot cycles and show that they are manifestation of the two surges of toroidal field - the one generated from the poloidal field advected all the way on the surface to the poles, down to the tachocline and equatorward to sunspot latitudes, and another one generated from the poloidal field diffused at midlatitudes from the surface to the tachocline and transformed there into toroidal field. The existence of these two surges of toroidal field is due to the relative ...
Concepts involving combined gas-turbine/steam-turbine power-generation plants, in which the fuel gas for the gas turbine is produced via the gasification of coal, are now extremely advanced. This technology already permits efficiencies of around 50% current development targets view 65% as achievable. In conventional technology, efficiencies are tied to conditions, such as air and cooling-water temperatures, at the particular location. In combined-cycle power plants, the properties of the fuel coal also play an important part. There are, in face, coals which can be more advantageously used in a combined-cycle power plant than in a conventional one. These differences, combined with advantageous concepts for coal-fired combined-cycle power-generating plants, are presented and analyzed. Particular attention is devoted to individual losses occurring at coal conversion, thermodynamic cycles, integration of ...
A series of hydrogenation/dehydrogenation cycles have been performed on palladium wire samples, stressed by a constant mechanical tension, in order to investigate the changes in electrical and mechanical properties. A large increase of palladium electrical resistivity has been reported due to the combined effects of the production of defects linked to hydrogen insertion into the host lattice and the stress applied to the sample. An increase of the palladium sample strain due to hydrogenation/dehydrogenation cycles in ????? phase transitions is observed compared to the sample subjected to mechanical tension only. The loss of initial metallurgical properties of the sample occurs already after the first hydrogen cycle, i.e. a displacement from the initial metallic behavior (increase of the resistivity and decrease of thermal coefficient of resistivity) to a worse one occurs already after the first hydrogen ...
A new process engineering flowsheet reflecting an improved design of the LASL Bismuth Sulfate thermochemical cycle is presented. The design is based on laboratory data that indicate a lowered endothermic heat load for a partial decomposition of the solid bismuth sulfate. A small electrical energy demand should result from operation of the sulfur dioxide electrolytic step at lower acid concentration, in principle. The results of the flowsheeting analysis yield a thermal efficiency of 50% for the cycle when coupled to a conceptual fusion energy heat source at 1500/sup 0/K. A parametric analysis shows a slight drop in efficiency as the temperature of the heat source is decreased. The LASL Bismuth Sulfate thermochemical cycle appears to have potential as a means of producing hydrogen from high-temperature heat sources such as fusion, fission, and solar energy; it also appears to be competitive with alternative thermochemical ...
This study describes the construction of a simple mathematical model its validation through the simulation in transient state of a real cycle performed by a solar refrigerator based on physical adsorption using an activated carbon/methanol pair. The deviation from experimental results was 4% for the cycled mass of methanol, 2.2 % for maximum collector average temperature, and 3 x 10{sup -3} for the theoretical cycle coefficient of performance. Additional simulations of the same cycle inputting values representing different types and larger amounts of activated carbon showed the possibility of increasing the cycled methanol mass up to about 150%. (author) 26 refs., 16 figs., 9 tabs.
Long life cycles covering more than one year are known for all orders of insects. There are different mechanisms of prolongation of the life cycle: (1) slow larval development; (2) prolongation of the adult stage with several reproduction periods; (3) prolongation of diapause; (4) combination of these mechanisms in one life cycle. Lasting suboptimal conditions (such as low temperature, low quality of food or instability of food resources, natural enemies, etc.) tend to prolong life cycles of all individuals in a population. In this case, the larvae feed and develop for longer than a year, and the active periods are interrupted by dormancy periods. The nature of this dormancy is unknown: in some cases it appears to be simple quiescence, in others it has been experimentally shown to be a tru...
The closed-cycle hydrogen-oxygen PEM regenerative fuel cell (RFC) at Nasa Glenn Research Center has successfully demonstrated closed-cycle operation at rated power for multiple charge/discharge cycles. During the charge cycle the RFC has absorbed input electrical power simulating a solar day cycle ranging from zero to 15 kWe peak, and delivered steady 5 kWe output power for periods exceeding 8 h. Orderly transitions from charge to discharge mode, and return to charging after full discharge, have been accomplished without incident. The RFC is beginning to demonstrate its potential as an energy storage device for aerospace solar power systems such as solar electric aircraft, lunar and planetary surface installations - any airless environment where minimum system weight is critical. This hard...
Tunable output wavelength is an important character of a free electron laser (FEL). As generally understood, to alter the wavelength of a high-gain harmonic generation (HGHG) FEL laser, the seed laser must be tunable. A few-cycle, high intensity laser obtained by optical compression usually has pretty broad bandwidth in the spectral domain, which can be used as the seed laser of a HGHG and may open the possibility to approach a HGHG scheme with fully tunable wavelength. In this paper, a HGHG FEL seeded by a few-cycle laser is theoretically discussed and numerically investigated. A few-cycle seed laser significantly influences HGHG FEL performance, especially in output wavelength tuning. For a HGHG FEL seeded by a 4-cycle 786 nm laser, output wavelength tunability range up to 14.9% of the central wavelength 262 nm is observed by adjusting the resonant condition.
The objective of this study is to analyze the effects of heat loss characterized by a percentage of the fuel's energy, friction and variable specific heats of working fluid on the performance of an air standard Otto cycle with a restriction of maximum cycle temperature. A more realistic and precise relationship between the fuel's chemical energy and the heat leakage that is based on a pair of inequalities is derived through the resulting temperature. The variations in power output and thermal efficiency with compression ratio, and the relations between the power output and the thermal efficiency of the cycle are presented. The results show that the power output as well as the efficiency where maximum power output occurs will increase with increase of the maximum cycle temperature. The temp...
Japan's basic nuclear policy is to reprocess spent fuel and to effectively use the recovered plutonium and uranium. MOX fuel utilization in LWRs is promoted in 16-18 reactors by FY2015. Commercial operation of Rokkasho Reprocessing Plant is planned to start in 2012. Prototype reactor 'Monju' restarted operation in May 2010. From FY 2007, Fast Reactor Cycle Technology Development Project (FaCT project) started which focuses more toward the commercialization stage FBR cycle. Basic scenario of Japan's R and D aims for realization of demonstration FBR by around 2025 and introducing commercial FBRs before 2050. Smooth transition from LWR fuel cycle to FBR one is an important point. For nuclear fuel cycle which requires long term R and D, human resources development and keeping is vitally important. (author)
The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.
The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.
The palladium(II) and platinum(II)complexes(where, (M(L){sub 2}X{sub 2}), M=Pd(II), Pt(II); L=isoxazole (isox), 3, 5-dimethylisoxazole(3, 5-diMeisox), 3-methyl, 5-phenylisoxazole(3-Me, 5-Ph-isox), and 4-amino-3, 5-di-methylisoxazole (4-ADI); X=Cl, Br) with isoxazole and its derivatives were investigated on antitumor activity by MM2 and EHMO calculation. Because for all the complexes the {sigma}MO energy level (E{sub {sigma}}{sub (M-X)} between d{sub x}{sup 2}{sub -y}{sup 2} orbital of central metal and p{sub x} orbital of halogen atom is less than {sigma}MO energy level E{sub {sigma}}{sub (M-N)} between d{sub x}{sup 2}{sub -y}{sup 2} orbital of central metal and p{sub x} orbital of N atom, without exception. And judging, from the lower E{sub {sigma}}{sub (M-X)} value in trans, the bonding strength was found to be weaker in trans isomer than in cis. For the Pd(II) and ...
Varying coordination modes of the Schiff base ligand H"2L [5-methyl-1-H-pyrazole-3-carboxylic acid (1-pyridin-2-yl-ethylidene)-hydrazide] towards different metal centers are reported with the syntheses and characterization of four mononuclear Mn(II), Co(II), Cd(II) and Zn(II) complexes, [Mn(H"2L)(H"2O)"2](ClO"4)"2(MeOH) (1), [Co(H"2L)(NCS)"2] (2), [Cd(H"2L)(H"2O)"2](ClO"4)"2 (3) and [Zn(H"2L)(H"2O)"2](ClO"4)"2 (4), and a binuclear Cu(II) complex, [Cu"2(L)"2](ClO"4)"2 (5). In the complexes 1-4 the neutral ligand serves as a 3N,2O donor where the pyridine ring N, two azomethine N and two carbohydrazine oxygen atoms are coordinatively active, leaving the pyrazole-N atoms inactive. In the case of complex 5, each ligand molecule behaves as a 4N,O donor utilizing the pyridine N, one azomethine N...
The biosorption characteristics of Pb(II) and Cd(II) ions from aqueous solution using the green alga (Ulva lactuca) biomass were investigated as a function of pH, biomass dosage, contact time, and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by U. lactuca biomass. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The monolayer biosorption capacity of U. lactuca biomass for Pb(II) and Cd(II) ions was found to be 34.7 mg/g and 29.2 mg/g, respectively. From the D-R isotherm model, the mean free energy was calculated as 10.4 kJ/mol for Pb(II) biosorption and 9.6 kJ/mol for Cd(II) biosorption, indicating that the biosorption of both metal ions was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, ...
Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were filled with steam. Two testing temperatures were employed, each with its own steam condition. These temperatures and steam conditions were 650/sup 0/F with saturated steam (5% liquid, 95% vapor) and 1200/sup 0/F with superheated steam at 2200 psi. The low-cycle fatigue tests were carried out at both 650/sup 0/F and 1200/sup 0/F by cycling the strain between equal tensile and compressive magnitudes until specimen failure or until it was no longer practical to continue the test. The creep-fatigue tests were carried out to failure by cycling the strain in the same fashion as in the low-cycle fatigue tests but with holds imposed at either the peak tensile strain or the peak compressive strain or at both peak tensile and compressive strains in each loading ...
The LiMnO{sub 2} lamellar oxide, obtained by exchange reaction from its sodium homologue {alpha}-NaMnO{sub 2}, has been used as a positive electrode for lithium batteries. After the first electrochemical cycle, the shape of the potential-composition curve changes and indicates a change in the structure. This modification changes imperceptibly at each cycle and after about 40 cycles, a stationary state is reached. Powder spectra refinement using the Rietvelt method shows a migration of manganese ions from the thin sheets towards the inter-sheet space. After a single cycle, 8% of the manganese ions are already present in the lithium site and this rate reaches 13% after 3 cycles. During long cycling, a redistribution of ions and vacancies inside the cfc oxygenated pile leads to a structure very similar to the LiMn{sub 2}O{sub 4} spinel. This structure evolution is ...
Characteristic study for the recycled fuel cycle, MOX fuel and Th-MOX fuel in PWR was performed with the comparison of 4 w/o UO2 fuel. It was assumed that there are no limit in reprocessing and no technical difficulty in recycling of spent fuel. The effect of recycling, plutonium composition, conversion ratio, MTC, FTC was investigated to each cycle. (Th+Pu)O_2 recycle option was advantageous because the loading amount of plutonium could be reduced from 8.3 w/o at once-through cycle to 3.5 w/o. (Th+Pu)O_2 recycled fuel was known to be higher Pu-239 consumption rate and more Pu-240(242) production rate. The (Th+U)O2 and (U+Pu)O2 once-through fuel cycle revealed high conversion ratio. The (U+Pu)O_2 recycled fuel cycle, however, showed low conversion ratio. Safety of each cycle was ensured by negative MTC and FTC
The interaction of cis-diamminediaquoplatinum(II) nitrate with adenosylcobalamin and a series of alkylcobalamins was studied by carbon-13 nuclear magnetic resonance spectroscopy and by electronic spectroscopy. With these cobalamins cis-(Pt(NH/sub 3/)/sub 2/(OH/sub 2/)/sub 2/)/sup 2 +/ forms adducts in which N(3) of the 5,6-methylbenzimidazole moiety is co-ordinated to platinum(II) rather than to cobalt(III) of the corrin. The chemical shifts of the 5'-methylene carbon of adenosylcobalamin-platinum adduct and of the Co-methyl carbon of the methylcobalamin-platinum adduct are characteristic of these cobalamins in the base-off form. Furthermore, these cobalamin-platinum complexes have visible spectra identical to those of the cobalamins in acidic solution. The /sup 13/C NMR spectrum of the adenosylcobalamin-platinum complex suggests the presence of a second adduct in which platinum(II) complexes are co-ordinated to ...
Porous phosphate heterostructures (PPH), functionalized with different ratios of aminopropyl and mercaptopropyl groups, labelled as Nx=5,25,50-PPH and Sx=5,25,50-PPH, respectively, were tested as adsorbents for Ni(II) and Hg(II) found in industrial sewage from electroplating processes and button battery recycling. X-ray diffraction was used to study the structures. The specific surface area of the pristine material (PPH) was 620m^2g^-^1, whereas the specific surface areas of the modified mercaptopropyl (S5-PPH) and aminopropyl (N5-PPH) were 472 and 223m^2g^-^1, respectively. The adsorption data were fitted to a Langmuir isotherm model. The S5-PPH material was saturated by 120mmol Hg(II) per 100g of material, whereas for Ni(II) adsorption, N25-PPH material displayed the highest adsorption w...
The relationship between serum PG I, PG II levels and extent of atrophic gastritis was examined. The subjects were 64 patients (male: 32, female: 32, 51.9 years old on average) with established diagnosis of either atrophic gastritis or normal. In the X-ray gastric examination, Fuji Computed Radiography (FCR) was used to obtain clear-cut images of the gastric area. Concerning the serum PG I level, patients in the group with atrophic gastritis showed lower levels than those of the people in the group with no atrophic change, but the variation was wide, and no definite tendency was seen in the relationship between the atrophic change and the serum PG I levels. Concerning the serum PG II level, as the atrophic change progresses, the serum PG II level tended to increase gradually. A significant reduction in the PG I/II ratio was seen in the group with atrophic changes (p<0.01) in comparison with the group ...
The relationship between serum PG I, PG II levels and extent of atrophic gastritis was examined. The subjects were 64 patients (male: 32, female: 32, 51.9 years old on average) with established diagnosis of either atrophic gastritis or normal. In the X-ray gastric examination, Fuji Computed Radiography (FCR) was used to obtain clear-cut images of the gastric area. Concerning the serum PG I level, patients in the group with atrophic gastritis showed lower levels than those of the people in the group with no atrophic change, but the variation was wide, and no definite tendency was seen in the relationship between the atrophic change and the serum PG I levels. Concerning the serum PG II level, as the atrophic change progresses, the serum PG II level tended to increase gradually. A significant reduction in the PG I/II ratio was seen in the group with atrophic changes (p<0.01) in comparison with the group ...
The biosorption characteristics of Cd(II) ions using the red alga (Ceramium virgatum) were investigated. Experimental parameters affecting the biosorption process such as pH, contact time, biomass dosage and temperature were studied. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherms. The biosorption capacity of C. virgatum biomass for Cd(II) ions was found to be 39.7 mg/g. From the D-R isotherm model, the mean free energy was calculated as 12.7 kJ/mol, indicating that the biosorption of Cd(II) the metal ions was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, {delta}H{sup o} and {delta}S{sup o}) showed that the biosorption of Cd(II) ions onto C. virgatum was feasible, spontaneous and exothermic at 293-323 K. Evaluation of experimental data in terms of biosorption kinetics showed that the biosorption of ...
Apparent molar volumes V{sub phi} and apparent molar heat capacities C{sub p,phi} were determined for aqueous solutions of nickel(II) nitrate, copper(II) nitrate, and zinc(II) nitrate at molalities m=(0.01 to 0.5) mol {center_dot} kg{sup -1}, and at the pressure p=0.35 MPa. Solution densities obtained using a vibrating-tube densimeter at T=(278.15 to 368.15) K were used to calculate V{sub phi} values. Heat capacity measurements obtained with a twin fixed-cell, differential-output, power-compensating, temperature-scanning calorimeter at T=(278.15 to 393.15) K were used to calculate values of C{sub p,phi}. Our results were then fitted to functions of m and T and compared to literature values.
The chemical operational concept originally established for the water-steam circuit of Angra II nuclear power plant has undergone several modifications throughout the development of the project. This work discusses the two main modifications giving special attention to the costs involved and analyses the main points and the consequences of such modifications 1 ref., 4 figs., 2 tabs.
System-level-operational testing of the ETX-II test-bed electric vehicle is described and the results discussed. Because the traction battery is a major factor in the performance of an electric vehicle, previously reported work on the sodium-sulfur battery designed for use with the ETX-II is reviewed in detail. Chassis dynamometer performance of the test-bed vehicle met or exceeded design goals and compared reasonably well with SIMPLEV computer modeling results. Areas are identified wherein further work is needed to establish a firmer basis for comparison of the simulation and the observed results.
A lot of effort has been made to spread the application of RTOS in embedded system development in China. RTOS, #mu#C/OS and #mu#C/OS-II, with its opened source code, is well known in embedded systems. Learning RTOS, Using RTOS, becomes more and more popular. The Book of 'Micro C/OS-II The Real-Time Kennel Second Edition' was published in 2002. Here some new progress of the RTOS, especially the safety certifications, the reliability of software is introduced. (authors)
The goal of this DOE Vision-21 project work scope is to develop an integrated suite of software tools that can be used to simulate and visualize advanced plant concepts. Existing process simulation software does not meet the DOE's objective of ''virtual simulation'' which is needed to evaluate complex cycles. The overall intent of the DOE is to improve predictive tools for cycle analysis, and to improve the component models that are used in turn to simulate the cycle. Advanced component models are available; however, a generic coupling capability that will link the advanced component models to the cycle simulation software remains to be developed. In the current project, the coupling of the cycle analysis and cycle component simulation software will be based on an existing suite of programs. The challenge is to ...
The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. Along with the major activity of assembling the components of the 50-lb/hr retort, work was also completed in other areas this quarter. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market applications for KENTORT II-derived products, a study of the synthesis of carbon fibers from the heavy fraction of KENTORT II shale oil was initiated.
Active Activator (Ac) elements undergo mutations to become nonautonomous Dissociation (Ds) elements at a low frequency. To understand...Full Text Available
... in Taylor and Williamson.* Most satellite sensors cannot be ... The coordinates of the rocket Ii ... I - Incoming Global Radiant Flux between 0.285 and ...
Abstract Copper(II) bis(thiosemicarbazone) are very useful for blood flow and hypoxic imaging. The aim of this study was to identify structure-activity relationships (SARs) within a series of analogues with different substitution patterns in the ligands, in order to design improved hypoxia imaging agents and elucidate hypoxia selectivity mechanisms. Genetic algorithms (GAs) were used to develop specific copper metal-ligand force field parameters for the MM3 force-field calculations. These new parameters produced results in good agreement with experiment and previously reported copper metal-ligand parameters. A successful quantitative SAR (QSAR) for predicting the several classes of Cu(II)-chelating ligands was built using a training set of 21 Cu(II) complexes. The QSAR exhibited a correlat...
missionaries and cannibals puzzle. He noted that in order to be able to use a boat to cross a river one would need ... a quali cation that the vertical exhaust stack ...
... And those who study cognition select problems (eg, tower of Hanoi, missionaries and cannibals, logic theorems) with minimal perceptual and motor ...
Form as the end result of massive star evolution; Type II supernova: collapse of iron core in highly evolved massive star; outer regions blasted away in ...
... centers in materials research. MRSECs address fundamental materials research topics of intellectual ... in materials research. II. PROGRAM DESCRIPTION MRSECs are supported by NSF to undertake materials ...
The biosorption of lead, copper and zinc ions on Rhizopus arrhizus has been studied for three single-component and two binary systems. The equilibrium data have been analysed using the Freundlich adsorption model. The characteristic parameters for the Freundlich adsorption model have been determined and the competition coefficients for the competitive biosorption of Pb(II)-Cu(II) at pH 4.0 and 5.0, and Pb(II)-Zn(II) at pH 5.0 have been calcualted. For the individual single-component isotherms, lead has the highest biosorption capacity followed by copper, then zinc. The capacity of lead in the two binary systems is always significantly greater than those of the other metal ions, in agreement with the single-component data. Only a partial selectivity for copper ions has been obtained at pH 4.0. (orig.)
Hexavalent chromium in corrosion preventive coating 64 ...To prevent corrosion of rims, weights can be provided with a coating. ...integrated clips brought up technical problems due to corrosion
... Science, Computer Vision, Digital Government, Digital Libraries, Digital Society and Technologies ... for Robust Intelligence, Digital Government, and Digital Libraries and Archives. In subsequent years ...
... Ready-to-Eat (MRE) VIII operational ration was evaluated at a field training exercise (Market Square II) with troops of the 82nd Airborne Division. ...
Given a double complex $X$ there are spectral sequences with the $E_2$ terms being either H$_I$ (H$_{II}(X))$ or H$_{II}($H$_I (X))$. But if $H_I(X)=H_{II}(X)=0$ both spectral sequences have all their terms 0. This can happen even though there is nonzero (co)homology of interest associated with $X$. This is frequently the case when dealing with Tate (co)homology. So in this situation the spectral sequences may not give any information about the (co)homology of interest. In this article we give a different way of constructing homology groups of $X$ when H$_I(X)=$H$_{II}(X)=0$. With this result we give a new and elementary proof of balance of Tate homology and cohomology.
This objective of this work was to summarize the main results obtained in previous papers related to the adsorbent-adsorbate interactions involved in the adsorption of naphthalenesulphonic acids and heavy metals (Cd(II) or Hg(II)) by modified activated carbons. The adsorption of organic compounds (1-naphthalenesulphonic acid, 1,5-naphthalenedisulphonic acid and 1,3,6-naphthalenetrisulphonic acid) and inorganic species (Cd(II) and Hg(II)) was studied on a series of ozonized activated carbon in aqueous phase. Commercial activated carbon (Filtrasorb 400) was treated with different ozone doses to study the effect of ozone treatment on its surface properties and investigate the behavior of the treated carbon samples in the above adsorption processes. After ozonation, carbonyl- and carboxyl-type...
Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this study, ALSTOM Power Inc. (ALSTOM) has investigated several coal fired power plant configurations designed to capture CO{sub 2} from effluent gas streams for use or sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). Additionally, oxygen firing in Circulating Fluid Bed Boilers (CFB's) can be more economical than ...
The purpose of this study is to determine the thermal reliability of stearic acid, palmitic acid, myristic acid and lauric acid as latent heat energy storage materials with respect to various numbers of thermal cycles. The fatty acids, as phase change materials (PCMs), of industrial grade (purity between 90% and 97%) were subjected to accelerated thermal cycle tests. The differential scanning calorimetry (DSC) analysis technique was applied to the PCMs after 0, 120, 560, 850 and 1200 melt/freeze cycles in order to measure the melting temperatures and the latent heats of fusion of the PCMs. The DSC results indicated that the change in melting temperature for the PCMs was in the range of 0.07-7.87 {sup o}C, and the change in latent heat of fusion was -1.0% to -27.7%, except for stearic acid between 560 and 1200 melt/freeze cycles. However, the decrease in the latent heats of fusion for all the PCMs was ...
The purpose of this study is to determine the thermal reliability of stearic acid, palmitic acid, myristic acid and lauric acid as latent heat energy storage materials with respect to various numbers of thermal cycles. The fatty acids, as phase change materials (PCMs), of industrial grade (purity between 90% and 97%) were subjected to accelerated thermal cycle tests. The differential scanning calorimetry (DSC) analysis technique was applied to the PCMs after 0, 120, 560, 850 and 1200 melt/freeze cycles in order to measure the melting temperatures and the latent heats of fusion of the PCMs. The DSC results indicated that the change in melting temperature for the PCMs was in the range of 0.07-7.87 deg. C, and the change in latent heat of fusion was -1.0% to -27.7%, except for stearic acid between 560 and 1200 melt/freeze cycles. However, the decrease in the latent heats of fusion for all the PCMs was not ...
The hydrozoa life cycle is characterized, in normal conditions, by the alternation of a post-larval benthic polyp and an adult pelagic medusa; however, some species of Hydrozoa react to environmental stress by reverting their life cycle: i.e. an adult medusa goes back to the juvenile stage of polyp. This very uncommon life cycle could be considered as some sort of inverted metamorphosis. A morphological study of different stages during the reverted life cycle of Turritopsis nutricula led to the characterization of four different stages: healthy medusa, unhealthy medusa, four-leaf clover and cyst. The ultrastructural study of the cellular modifications (during the life cycle reversion of T. nutricula) showed the presence of both degenerative and apoptotic processes. Degeneration was prevalent during the unhealthy medusa and four-leaf clover stages, while the apoptotic rate was higher ...
There are various interesting semantics' (extensions) designed for argumentation frameworks. They enable to assign a meaning, e.g., to odd-length cycles. Our main motivation is to transfer semantics' proposed by Baroni, Giacomin and Guida for argumetation frameworks with odd-length cycles to logic programs with odd-length cycles through default negation. The developed construction is even stronger. For a given logic program an argumentation framework is defined. The construction enables to transfer each semantics of the resulting argumentation framework to a semantics of the given logic program. Weak points of the construction are discussed and some future continuations of this approach are outlined.
The determinants of the velocity of money have been examined based on life-cycle hypothesis. The velocity of money can be expressed by reciprocal of the average value of holding time which is defined as interval between participating exchanges for one unit of money. This expression indicates that the velocity is governed by behavior patterns of economic agents and open a way to constructing micro-foundation of it. It is found that time pattern of income and expense for a representative individual can be obtained from a simple version of life-cycle model, and average holding time of money resulted from the individual's optimal choice depends on the expected length of relevant planning periods.
In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.
The restricted temperature stability of the synthetic thermal oil which is used as heat carrier fluid in parabolic trough collectors so far limits the live steam parameters in the steam cycle to approximately 375 Celsius. In order to break through this limit, already for quite some time it is researched to replace the thermal oil by boiler feeding waters and to accomplish the evaporation in the collectors. The contribution under consideration gives an overview on the direct evaporation concept and summarizes the past operational experiences. Moreover, the challenges with the integration of this technology in a steam turbine cycle are elaborated.
Experimental data on the material characteristics of structures subjected to thermal and mechanical cycling are needed for designing structural parts for creep and creep-fatigue interaction. Moreover, high-temperature low-cycle fatigue data are not sufficient to predict the fatigue creep lifetime. In order to check the reliability of steam generators, tests on pipe materials are conducted under cyclic thermal loading. The tests have been performed on an iron-nickel chromium alloy (alloy 800). Isothermal low-cycle fatigue tests have been conducted at 550 C. 15 refs.
National Power is building its first gas turbine combined cycle power station at Killingholme, situated to the south of the River Humber in the East of England. NEI ABB Gas Turbines Limited was awarded the turnkey contract in July 1990 to build a nominal 650 MW combined cycle power station based around three Asea Brown Boveri GT13E gas turbines. The project is outlined in this article. The plant is due for completion in July 1993. (author)
This contribution describes our research and development effort towards an electrically rechargeable zinc/air battery which is capable of meeting the demands of a scaled power profile (driving-cycle tests). The power profiles DST (Dynamic Stress Test) and ECE15-L (European Driving Cycle for alkaline Batteries) were applied to our 200 and 50 cm{sup 2} electrically rechargeable Zn/O{sub 2} cells with nominal capacities of 30 and 7.5 Ah, respectively. (authors)
According to China's 'Medium- and Long-term Nuclear Power Development Program (2005-2020)', nuclear energy development in China will take the technical line of closed nuclear fuel cycle. This paper discusses the significance of closed nuclear fuel cycle, and briefly introduces development trends in the world. This article also discusses the opportunity to construct spent fuel reprocessing plant; equilibrium of plutonium production and consumption; adaptability and economics to use MOX fuel in the thermal neutron reactor. Some suggestions are put forward to the overall development of nuclear energy in China. (authors)
The design of a solar heated cavity receiver transferring 60 MW of thermal energy to the working medium (air) for a closed-cycle gas turbine is described. The gas turbine plant with its cycle layout is presented. Then the tubes for the receiver are designed taking into account thermal and mechanical loads. It is shown how the occurring stresses are influenced by the destribution of the locally absorbed hat flux. Calculations for an existing coal fired air heater of a closed-cycle gas turbine give a first impression of the long-term behaviour to be expected of the receiver tubes.
Condensing curves are presented for a number of two-component mixed hydrocarbon working fluids which are potentially usable in binary geothermal cycles. Performance of geothermal thermodynamic cycles incorporating these fluids has been evaluated under separate cover; two figures summarizing the results of those evaluations have been included here for continuity. The purpose of this report is: first, to document the condensing curves which were used in the mixed fluid cycle analyses, and second, to provide background useful in the preliminary evaluation of heat rejection systems for advanced geothermal electric power plants utilizing mixed hydrocarbon working fluids. Some concluding remarks are presented.
Calcium stannate (CaSnO3) powders with the distorted perovskite structure have been synthesized by solid state and the sol-gel methods and their electrochemical performance was compared. The sol-gel CaSnO3 shows stable cycling performance with a reversible capacity of 430-440 mAh/g (0.005-1.0 V; 60 mA/g) up to 50 cycles. The role of preparatory conditions, morphology and cycling conditions (current density and potential window) on the anodic performance of the compounds are addressed.
Desiccant cooling is a potentially environmentally friendly technology that can be used to condition the internal environment of buildings. Unlike conventional air conditioning systems, which rely on electrical energy to drive the cooling cycle, desiccant cooling is a heat-driven cycle. This paper follows on from an initial study by the authors, and uses real meteorological data to evaluate the potential in the United Kingdom of using solar energy to drive the desiccant cooling cycle. Through the use of parametric studies, the paper investigates the energy consumption and costs associated with desiccant cooling. (author)
Microscopy and chemotaxonomy from HPLC analysis of phytoplankton pigments initiated in 2003 suggest that Noctiluca miliaris blooms are becoming more intense ...
2.1 The Importance of Life Cycle Management and Cost Estimating................. ........... 1-2 .... 4.3.5 Task 12: Update Cost Estimate on Regular Basis. ...
This article describes how a natural gas-fired combined cycle with increased firing temperature, reduced cooling air usage, improved component efficiencies, and cycle enhancements could achieve a lower heating value plant efficiency of greater than 60%. Today's gas turbine systems feature high fuel-to-electricity efficiencies. Efficiencies, on a lower-heating-value (LHV) basis, for large natural gas-fired combined-cycle systems for the utility market have been demonstrated at 54%. Even though manufacturers will make improvements in the 1990s, efficiency levels will reach a plateau. Cycle innovations and gas turbine design changes will achieve LHV efficiencies in the 60% range for natural gas-fired utility machines.
Simple hydroxamic acids are shown to be useful reagents for the separation of Np and Pu from U within simplified, single cycle Purex flowsheets. They are compatible with the use of centrifugal contactors and laboratory scale flowsheet trials with aceto-hydroxamic acid have demonstrated high actinide recoveries and decontamination factors on products for active feeds of up to 40 wt.% Pu. They therefore show many ideal characteristics for Pu and Np recovery within flowsheet options for actinide recovery in advanced fuel cycles. Furthermore, in order to optimise the routing of Np with the Pu product in advanced flowsheets, additional studies of Np extraction in the primary co-decontamination contactor, prior to U/Pu partition, have been undertaken, combining experiment, modelling and flowsheet tests. (author)
The removal of toxic metals and alkalis from gas streams at high temperatures was investigated. This is important for the development of coal-fired combined cycle power generation systems.
Many nations and international agencies are working to develop improved technology and industrial capability for neuclear fuel cycle and waste management operations. The effort in some countries is limited to research in university laboratories on treating low-level waste from reactor plant operations. In other countries, national nuclear research institutes are engaged in major programs in all phases of the fuel cycle and waste management, and there is a national effort to commercialize fuel cycle operations. Since late 1976, staff members of Pacific Northwest Laboratory have been working under US Department of Energy sponsorship to assemble and consolidate openly available information on foreign and international nuclear waste management programs and technology. This report summarizes the information collected on the status of fuel cycle and waste management programs in selected countries making major ...
ABSTRACT Shallow-lacustrine delta deposits of the Upper Triassic Yanchang Formation form the most important petroleum reservoir sandstone units in the Ordos Basin, China. Recent hydrocarbon exploration and outcrop studies demonstrated that shallow-lacustrine sand-rich deltas developed extensively along the gentle flanks and central part of the basin. The vertical succession of facies indicates that the Yanchang Formation records the entire lacustrine life cycle of the Late Triassic Ordos Basin. Four third-order transgressive-regressive cycles and two larger shallow-lacustrine deltaic cycles have been recognized. A process-based depositional model, derived in part from the modern Ganjiang delta in Poyang Lake, China, is used to infer the origins of the sand-rich lacustrine delta deposits. S...
Knowledge about retinal photoreceptor signal transduction and the visual cycle required for normal eyesight has expanded exponentially over the past decade. Substantial progress in human genetics...Full Text Available
In order to investigate the charging mode of an in-series assembly of lithium-carbon battery cells, a test has been performed on 5 commercial cells (18650) of 0.95 Ah nominal capacity. Results show that it is possible to cycle the cells at 80% of their output capacities during more than 2000 cycles. The management of the battery consists in maintaining a constant battery voltage as soon as a cell reaches its limit voltage during constant current charging. The initial dispersion of cells has been maintained practically constant during the cycling and the charge state of all cells has decreased progressively. (J.S.)
Questionnaires and twice daily peak expiratory flow measurements were used to evaluate the effects of the menstrual cycle in asthmatic women. Forty per cent of women reported premenstrual deterioration...Full Text Available
These include, but are not limited to: stellar winds and outflows, post-main- sequence stellar evolution, binary/multiple star evolution, globular cluster ...
These include, but are not limited to: stellar winds and outflows, post-main- sequence star evolution, binary star evolution, globular cluster structure and ...
... of electronic systems (satellite terminals, radio and ... helps organizations investigate the stochastic nature of ... cycle time, maximum queue lengths, and ...
Urban heritage areas throughout the world have experienced cycles of neglect and upgrade that were at times intentional and at other times due to economic difficulties or an unbalanced ideological focus on technological, social or political developments. Modernism of the early and mid-1900s was clearly against keeping heritage areas as they were perceived to hinder future developments. Postmodernist thinking afterwards was more sympathetic to heritage as a means of countering the 'placelessness' of the modern city. Global appreciation of urban heritage and the world's cultural diversity at the end of the century made the occurrence of 'physical neglect' cycles very unlikely in the future. This research paper takes the stand that urban planners and designers face cycles of higher or lower u...
This Memorandum, after summarizing the life cycle of the different species of human schistosome, reviews the present knowledge of the immunology of schistosomiasis. Each stage of the parasite contains...Full Text Available
Proliferating cells have been immunophenotypically characterized in lymph node and bronchoalveolar lavage (BAL) samples obtained from patients with active and inactive sarcoidosis with the cell-cycle-related...Full Text Available
The Heat Cycle Research Program, which is conducted for the Department of Energy, has as its objective the development of the technology for effecting the improved utilization of moderate temperature geothermal resources. The current testing involves the investigation of binary power cycle performance utilizing mixtures of non-adjacent hydrocarbons as the working fluids, with supercritical vaporization and in-tube condensation of the working fluid. The utilization of these concepts verified here will improve the net geofluid effectiveness (net watt hours plant output per pound of geofluid) about 20% over that of a conventional binary power plant. The major effect in this improvement is the ability to achieve integral, countercurrent condensation. Results are presented for the recent testing including those tests examining the performance of the countercurrent condenser at different tube inclinations and comparison with new design-base computer ...
BackgroundRecent studies have shown associations between size and body proportions at birth and health outcomes throughout the life cycle, but there are few data...Full Text Available
This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data are presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed.
A small fleet of classic London Taxis (Black cabs) equipped with hydrogen fuel cell power systems is being prepared for demonstration during the 2012 London Olympics. This paper presents a Life Cycle Analysis for these vehicles in terms of energy consumption and CO2 emissions, focusing on the impacts of alternative vehicle technologies for the Taxi, combining the fuel life cycle (Tank-to-Wheel and Well-to-Tank) and vehicle materials Cradle-to-Grave. An internal combustion engine diesel taxi was used as the reference vehicle for the currently available technology. This is compared to battery and fuel cell vehicle configurations. Accordingly, the following energy pathways are compared: diesel, electricity and hydrogen (derived from natural gas steam reforming). Full Life Cycle Analysis, usin...
Field studies among diverse biomes demonstrate that nitrogen concentration (% N) at leaf- and canopy-scales is strongly related to carbon uptake and cycling ...
During the service in nuclear power plants, steam generator (SG) tubing will suffer from a vibration with a frequency from 30-40 Hz. This means that SG tubing will undergo a very high cycle fatigue process during the design life time (25 years=about 3x10{sup 10}cycles). The material degradation and the very high cycle fatigue life of SG tubing materials due to the vibration are therefore of concern. In this investigation, the fatigue properties of Alloy 690 and Alloy 800 SG tubing in the very high cycle fatigue regime (higher than 10{sup 7} cycles) and strain controlled fatigue at temperatures up to 330{sup o}C have been investigated. The fatigue properties of SG tubing of Alloy 690 are comparable to that of wrought material. The strain controlled fatigue properties of Alloy 690 and Alloy 800 are slightly better at 288{sup o}C than at room temperature (RT). At the stress near the ...
During the service in nuclear power plants, steam generator (SG) tubing will suffer from a vibration with a frequency from 30-40 Hz. This means that SG tubing will undergo a very high cycle fatigue process during the design life time (25 years=about 3x10"1"0cycles). The material degradation and the very high cycle fatigue life of SG tubing materials due to the vibration are therefore of concern. In this investigation, the fatigue properties of Alloy 690 and Alloy 800 SG tubing in the very high cycle fatigue regime (higher than 10"7 cycles) and strain controlled fatigue at temperatures up to 330"oC have been investigated. The fatigue properties of SG tubing of Alloy 690 are comparable to that of wrought material. The strain controlled fatigue properties of Alloy 690 and Alloy 800 are slightly better at 288"oC than at room temperature (RT). At the stress near the fatigue endurance, ...
A test program was conducted under contract to Sandia National Laboratories to investigate water/steam effects on elevated temperature low cycle fatigue and creep-fatigue of Alloy 800. This report presents interpretation and analysis of the test results. Tubular specimens with water sealed inside were cycled to failure under strain control. Tests were conducted to 616K (650/sup 0/F) and 922K (1200/sup 0/F); some at 922K included tensile or compressive hold periods to simulate creep-fatigue conditions. The tubular specimens showed significantly lower lives than solid bar specimens cycled at equivalent strain ranges. Rough internal surfaces contributed to early crack initiation with these specimens. Inclusion of hold periods caused further large reductions in cycles to failure.
A feature of the Fast Flux Test Facility (FFTF) is that fuel assemblies can be stored within the reactor vessel, either for future use in the core or for temporary storage of spent fuel. Due to the close proximity of fuel assemblies stored in the in-vessel storage (IVS) locations to the ex-vessel flux monitors (EVFMs), neutrons originating in the stored fuel can result in significant contributions to the total EVFM signals. The paper shows EVFM-induced electronic current data during operation at full power for FFTF power cycles 1 through 7. The data were obtained early in each cycle so that signal drift due to core burnup could be ignored. The differences in currents are attributed to differences in cycle-to-cycle core and stored fuel loadings. At the beginning of cycle 1 there were no fuel assemblies stored in IVS. Subsequent to cycle 1, the EVFM currents have been higher than ...
BackgroundSenescence is integral to the flowering plant life-cycle. Senescence-like processes occur also in non-angiosperm land plants, algae and photosynthetic prokaryotes. Increasing...Full Text Available
Atterberg limits, free swell, and hydraulic conductivity tests were conducted to assess how wet-dry cycling affects the plasticity and swell of bentonite, and the hydraulic conductivity of geosynthetic clay liners (GCLs) hydrated with deionized (DI) water (pH 6.5), tap water (pH 6.8), and 0.0125-M CaCl{sub 2} solution (pH 6.2). The plasticity of bentonite hydrated with DI water increased during each wetting cycle, whereas the plasticity of bentonite hydrated with tap water and CaCl{sub 2} decreased during each wetting cycle. Wet-dry cycling in DI water and tap water had little effect on swelling of the bentonite, even after seven wet-dry cycles. However, swelling decreased dramatically after two wetting cycles with CaCl{sub 2} solution. Hydraulic conductivity of GCL specimens remained low during the first four wetting cycles ...
The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).
The first member of the Qingshankou Formation recovered by CCSD-SK-Is borehole (China Cretaceous Continental Scientific Drilling-SongkeI-the south borehole) is 81.41 m long, and the recovery of cores is 100%. The age of the member is approximately Turonian. The sequence and process of lithology-lithofacies and cyclic stratigraphy were revealed by a detailed core description. 6 rock types (mudstone, dolomite, marl, limestone, ostracode limestone, and volcanic ash) comprise the sedimentary strata. Deposition occurred in a deep lake, including 6 sedimentary microfacies: mudstone, sandy turbidite, dolomite, marl, limestone, and volcanic ash microfacies. The first member of the Qingshankou Formation represents 81 meter-scale cycles (sixth-order cycle), 25 fifth-order cycles, 6 fourth-order cycl...
We investigate the chemical and observational implications of repetitive transient dense core formation in molecular clouds. We allow a transient density fluctuation to form and disperse over a period of 1 Myr, tracing its chemical evolution. We then allow the same gas immediately to undergo further such formation and dispersion cycles. The chemistry of the dense gas in subsequent cycles is similar to that of the first, and a limit cycle is reached quickly (2 - 3 cycles). Enhancement of hydrocarbon abundances during a specific period of evolution is the strongest indicator of previous dynamical history. The molecular content of the diffuse background gas in the molecular cloud is expected to be strongly enhanced by the core formation and dispersion process. Such enhancement may remain for as long as 0.5 Myr. The frequency of repetitive core formation should strongly determine the level of background ...
This paper focuses on the application and features of a unified multi-machine train condition monitoring and diagnostic system as applied to a 340 MW repowered combined cycle power plant. Modifications during repowering of the plant required the addition of gas turbines, and design changes to the boiler and steam turbine. Operational procedure during startup also had to be developed. In order to improve the economics of operation, enhancement of both plant operational efficiency and availability were required. Thus it was decided to implement an on-line plant-wide multi-machine Condition Monitoring System. In this paper, the details of the condition monitoring system and some of the design details of the power plant are presented. Requirements of a condition monitoring system applicable to a combined cycle plant are also covered. Salient system design features are explained. The system has been implemented in a combined ...
Considering beryllium as plasma facing armour this paper presents recent results obtained in Russia. A special process of joining beryllium to a Cu-alloy material structure is described and recent results of thermal cycling tests of such joints are presented. Summarizing the results, the authors show that a Cu-alloy heat sink structure armoured with beryllium can survive high heat fluxes ({>=}10 MW/m{sup 2}) during 1000 heating/cooling cycles without serious damage to the armour material and its joint. The principal feasibility of thermal cycling of beryllium grades and their joints directly in the core of a nuclear reactor is demonstrated and the main results of this test are presented. The paper also describes the thermal cycling of different beryllium grades having cracks initiated by previously applied high heat loads simulating plasma disruptions. (orig.)
A process has been proposed to increase the efficiency of an ideal Otto cycle via a quantum heat engine that has no cooler reservoir. We show that such a process is not feasible.
A process for separation of actinides and technetium from reprocessing high level liquid waste has been developed, the CTH-process. The main parts are three consecutive solvent extraction cycles followed by an optional step for sorption on inorganic ion exchangers. The first extraction cycle removes and recovers uranium, neptunium, and plutonium by extraction with HDEHP. The second extraction cycle separates technetium and nitric acid from the waste using TBP. In the third extraction cycle Am and Cm are separated from the waste using HDEHP. The actinide free waste is then passed through inorganic ion exchangers to remove most of remaining radionuclides. The process has been tested on an authenic HLLW solution. A decontamination factor > 10/sup 5/ for alpha emitters was measured for the solvent extraction process and the sorption on inorganic ion exchangers gave a decontamination factor > 3x10/sup ...
Hamed, A. and A. Mohamed, "Assessment of Shock Induced Flow Separation and ...... AGARD Symposium on Combined Cycle Propulsion for Hypersonic Application, ...
Recent field observations have shown that the atmospheric plumes of quiescently degassing volcanoes are chemically very active, pointing to the role of chemical cycles involving halogen species and...Full Text Available
Research in concentrated thermal solar power plants of all types and, in particular, those based on central receiver, namely solar tower plants, has experienced great impetus in the last decade, reaching full commercial operation with the PS10 plant in Spain. In spite of previous demonstration plants testing different receivers and power cycle layouts, this first commercial power plant adopted a cavity receiver generating saturated steam and therefore penalising cycle efficiency in order to gain plant reliability. According to the experience gained, if a competitive Levelised Cost of Electricity is to be reached, capital and maintenance costs must be reduced and efficiencies must be increased. To achieve these goals, modifying the power cycle is deemed essential, whether using superheated ...
... of the cycle shows that the separation area ea. ... with suitable flow solvers based on the Reynolds ... AGARD 75th Fluid Dynamics Panel Meeting and ...
High Cycle Fatigue Initiative Workshop -Active Vibration. Control/Engine. Health Monitoring Session December 10,. 1996. The presentation was titled "Active ...
In order to study the intragenic profiles of active transcription, we determined the relative levels of active RNA polymerase II present at the 3′- and 5′-ends of 261 yeast genes by...Full Text Available
The temporal patterns of protein phosphorylation in the adrenal glomerulosa cell were analysed by two-dimensional electrophoresis after stimulation with 10 nM-angiotensin II or various agents [10 nM-12-O-tetradecanoylphorbol...Full Text Available
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for poly(allylamine) (PAA). Metal uptake studies show increases in ...
Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for poly(allylamine) (PAA). Metal uptake studies show increases in ...
The spin-up problem of He II in a cylindrical container of infinite and finite height is considered on the basis of the Hall-Vinen-Bekarevich-Khalatnikov equations. The boundary conditions include the assumption of the generation of superfluid vorticity at the walls of the container. In the lowest order approximation with respect to viscosity, the problem is reduced to a Stefan problem for a single diffusion-type equation. Examples of solutions are given which show that the method used gives a good insight into the physical development of the spin-up flow.
Type II NAD(P)H:quinone oxidoreductases (NDH-2) catalyze the two-electron transfer from NAD(P)H to quinones, without any energy-transducing site. NDH-2 accomplish the turnover of NAD(P)H, regenerating...Full Text Available
It is shown that observations of the lithium isotope ratio in high surface temperature Population II stars may be critical to cosmological nucleosynthesis models. In particular, decaying particle scenarios as derived in some supersymmetric models may stand or fall with such observations. 18 references.
These three volumes cover liposome technology in pharmacology and medicine. Contributors emphasize methodology used in their own laboratories, and include a brief introduction, coverage of relevant literature, applications and critical evaluations for the methods they describe. Volume II presents procedures for the entrapment of a number of drugs, including genetic material, into selected types of liposomes.
The theoretical evolution of a horizontal branch star of Population II is followed through the helium burning in the core phase and is compared with the results given by other investigators. The m- fluence of different physics and interpolation schemes in the opacity tables is discussed. Some thoughts are given on the explanation of the erratic period variations observed in some of the RR Lyrae variables in the globular clusters. (auth)
Experimental results are presented on the quasi-statistic polarization reversal and on the effect of high dc electric field on the behaviour of LiNH_4SO_4 and LiND_4SO_4 monocrystals, namely in the vicinity of the II-III phase transformation.
PurposeRTOG protocol 95-17 was a phase I/II trial to evaluate multi-catheter brachytherapy as the sole method of adjuvant breast radiotherapy for stage I/II breast...Full Text Available
A comparison was made of the advantages and disadvantages of two codes, SAND-II and FERRET, for determining the neutron flux spectrum and uncertainty from experimental dosimeter measurements as anticipated in the FFTF Reactor Characterization Program. This comparison involved an examination of the methodology and the operational performance of each code. The merits of each code were identified with respect to theoretical basis, directness of method, solution uniqueness, subjective influences, and sensitivity to various input parameters.
The answer to the title is ''NO''. The authors investigate the low energy particle spectra of type-II superstring theory after compactification to 4 dimensional space-time by means of the super Kac-Moody algebra as well as the twisted super Kac-Moody algebra. They show that there is no solution containing all of the particle contents in the standard model.
Several closely related Mn(II)-oxidizing alpha-Proteobacteria were isolated from very different marine environments: strain SI85-9A1 from the oxic/anoxic interface of a stratified...Full Text Available
The nature of binding of Ru(phen) 2+ (I), Ru(bipy) 2+ (II), Ru(terpy) 2+ (III) (phen = 1,10-phenanthroline, bipy 3 = 2,2'-bipyridyl, 3 terpy = 2,2'2," - 2 terpyridyl) to DNA, poly[d(G-C)] and poly[d(A-T)]...Full Text Available
This report summarizes the progress made on the development of an integrated multistage fluidized bed retorting process (KENTORT II) during the period of October 1, 1992 through September 30, 1993 under Cooperative Agreement No. DE-FC21-90MC27286 with the Morgantown Energy Technology Center, US Department of Energy. The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. The PDU was assembled, instrumented and tested during this fiscal year. Along with the major activity of commissioning the 50-lb/hr retort, work was also completed in other areas. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market applications for KENTORT ...
The properties of the highest velocity ejecta of normal Type Ia supernovae (SNe Ia) are studied via models of very early optical spectra of 6 SNe. At epochs earlier than 1 week before maximum, SNe with a rapidly evolving Si II 6355 line velocity (HVG) have a larger photospheric velocity than SNe with a slowly evolving Si II 6355 line velocity (LVG). Since the two groups have comparable luminosities, the temperature at the photosphere is higher in LVG SNe. This explains the different overall spectral appearance of HVG and LVG SNe. However, the variation of the Ca II and Si II absorptions at the highest velocities (v >~ 20,000 km/s) suggests that additional factors, such as asphericity or different abundances in the progenitor white dwarf, affect the outermost layers. The C II 6578 line is marginally detected in 3 LVG SNe, suggesting that LVG undergo less intense burning. The ...
A series of NHC silver(I), mercury(II) and palladium(II) complexes, [(1,3-diethylbimy)6Ag4I3]I (2), [(1-benzyl-3-picolylbimy)Ag2Br2]n (3), [(1-benzyl-3-picolylbimy)HgI(CH2CN)]2 (4), {[(1-picolyl-3-npropylbimy)2Hg][Hg2I6]}n (5) and [(1,3-dipicolylbimy)PdCl]Cl (6), as well as one anionic complex [1,3-diethylbimidazolium]2[HgI4] (1) (bimy=benzimidazol-2-ylidene), have been prepared and characterized. Interestingly, a wind wheel-like Ag4I3 arrangement in 2 is formed, 1D polymeric chain containing 12-membered macrometallocycles and quadrangle Ag2Br2 units in 3 is generated, and the a-carbon atom of deprotonated acetonitrile ([CH2CN]-) in 4 participates in coordination with mercury(II) atom. In the crystal packings of complexes 1-6, 2D supramolecular layers or 3D supramolecular architectures are...
A number of amines can be employed for all volatile treatment (AVT) of steam generator (SG) systems of nuclear power reactors. These amines form complexes with Cu{sup 2+} and Ni{sup 2+} ions which come into water due to corrosion. The redox reactions of a number of Cu(II)-AVT amine complexes and the stability of the transient species formed have been studied by pulse radiolysis technique. Rate constants for the reaction of e{sub aq}{sup -} with a number of Cu(II)-amine complexes have been determined by following the decay of e{sub aq}{sup -} absorption. Stability of Cu(I)-amine complexes was studied by following the kinetics of the bleaching signal formed at the {lambda}{sub max} of the Cu(II) amine complex. Except for Cu(I)-triethanolamine complex all other Cu(I)-amine complexes were found to be stable. One-electron oxidation of Cu(II) amine complexes was studied using azidyl radicals for the oxidation ...
Coutinho MF, Encarnao M, Gomes R, da Silva Santos L, Martins S, Sirois-Gagnon D, Bargal R, Filocamo M, Raas-Rothschild A, Tappino B, Laprise C, Cury GK, Schwartz IV, Artigals O, Prata MJ, Alves S. Origin and spread of a common deletion causing mucolipidosis type II: insights from patterns of haplotypic diversity. Mucolipidosis II (ML II alpha/beta), or I-cell disease, is a rare genetic disease in which activity of the uridine diphosphate (UDP)-N-acetylglucosamine:lysosomal enzyme N-acetylglucosamine-1-phosphotransferase (GlcNAc-phosphotransferase) is absent. GlcNAc-phosphotransferase is a multimeric enzyme encoded by two genes, GNPTAB and GNPTG. A spectrum of mutations in GNPTAB has been recently reported to cause ML II alpha/beta. Most of these mutations were found to be private or rare. ...
We study the condensation of localized closed string tachyons in C{sup 3}/Z{sub N} non-supersymmetric noncompact orbifold singularities via renormalization group flows that preserve supersymmetry in the worldsheet conformal field theory and their interrelations with the toric geometry of these orbifolds. We show that for worldsheet supersymmetric tachyons, the endpoint of tachyon condensation generically includes 'geometric' terminal singularities (orbifolds that do not have any marginal or relevant Kahler blowup modes) as well as singularities in co-dimension two. Some of the various possible distinct geometric resolutions are related by flip transitions. For Type II theories, we show that the residual singularities that arise under tachyon condensation in various classes of Type II theories also admit a Type II GSO projection. We further show that Type II orbifolds entirely devoid of ...
Our studies have shown that endotoxin intratracheally instilled into the rat lung induces proliferation of alveolar type II cells. In that study, the alveolar type II cells. In that study, the alveolar type II cell hyperplasia occurred 2 d after instillation of endotoxin and persisted for a further 2 d. After hyperplasia, the lung remodeled and returned to a normal state within 24-48 h. Understanding the mechanisms involved in the remodeling process of this transient hyperplasia may be useful to identify molecular changes that are altered in neoplasia. The purpose of the present study was to corroborate induction of epithelial cell hyperplasia by endotoxin and to delineate mechanisms involved in tissue remodeling after endotoxin-induced alveolar type II cell hyperplasia. In conclusion, immonostaining with cyclin D1 and cytokeratin shows that endotoxin induced epithelial cell proliferation and resulted ...
Two overlapping cDNA clones encoding human DNA topoisomerase II were identified by two independent methods. In one, a human cDNA library in phage {lambda} was screened by hybridization with a mixed oligonucleotide probe encoding a stretch of seven amino acids found in yeast and Drosophila DNA topoisomerase II; in the other, a different human cDNA library in a {lambda}gt11 expression vector was screened for the expression of antigenic determinants that are recognized by rabbit antibodies specific to human DNA topoisomerase II. The entire coding sequences of the human DNA topoisomerase II gene were determined from these and several additional clones, identified through the use of the cloned human TOP2 gene sequences as probes. Hybridization between the cloned sequences and mRNA and genomic DNA indicates that the human enzyme is encoded by a single-copy gene. The location of the gene was mapped to ...
The ability of white-rot fungus, Pycnoporus sanguineus to adsorb copper (II) ions from aqueous solution is investigated in a batch system. The live fungus cells were immobilized into Ca-alginate gel to study the influence of pH, initial metal ions concentration, biomass loading and temperature on the biosorption capacity. The optimum uptake of Cu (II) ions was observed at pH 5 with a value of 2.76 mg/g. Biosorption equilibrium data were best described by Langmuir isotherm model followed by Redlich-Peterson and Freundlich models, respectively. The biosorption kinetics followed the pseudo-second order and intraparticle diffusion equations. The thermodynamic parameters enthalpy change (10.16 kJ/mol) and entropy change (33.78 J/mol K) were determined from the biosorption equilibrium data. The FTIR analysis showed that -OH, -NH, C-H, C=O, -COOH and C-N groups were involved in the biosorption of Cu (II) ions onto immobilized ...
This report contains preconceptual designs and planning level life-cycle cost estimates for managing hazardous waste. The report`s information on treatment, storage, and disposal modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the US Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report.
This patent describes a turbocharger for a two-cycle engine having an oil mist containing crankcase and burning a mixture of liquid fuel containing lubricating oil therein wherein the turbocharger comprises a shaft mounted in a housing for rotation by an exhaust-driven turbine on one end to a drive compressor on the other end connected to supply pressurized air for the fuel/air mixture of the engine, the improvement to supply lubrication to the shaft and automatically enrichen the fuel/air mixture during high speed turbocharging.
Equations are derived to permit calculation of the work required for the isentropic compression of a two phase fuel-air mixture. Methanol evaporation during compression is shown to substantially reduce compression work and thereby improve cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. 14 refs.
Equations are derived to calculate the work required for the isentropic compression of a 2-phase fuel-air mixture. Methanol evaporation during compression substantially reduces compression work and improves cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. Energy d. of methanol and gasoline fuel-air charges are compared. The phase equilibrium and evaporation rate are causes of the poor cold-starting performance of methanol.
... Space weather is the biggest driver of ozone depletion and much else we are only beginning to understand. Solar Cycle 24 may turn out to be weak in terms of sun spot count but the amount of energy delivered by CME/SPE will probably not be. Remember that the Carrington Event in 1859 happened during a cycle with a lowish sun spot count. Recommend (1) Report abuse ...
The paper discusses the potential environmental impacts associated with the operation of a large, say 350 MWe, gas-fired combined cycle power station. It concludes that if appropriate control methods are introduced at the design stage of the plant, environmental impacts are minimal and can be considered acceptable. (author).
... As a consequence the Brazilian government introduced a thermoelectric priority programme covering the construction of new gas fired combined cycle power plants. One such plant has been constructed at the Suape industrial port complex in the state of Pernambuco. The US$350 million Termopernambuco combined cycle gas ...
This article describes the Monsanto's Indian Orchard plant gas-fired, combined-cycle cogeneration facility in Springfield, Massachusetts. The topics of the article include project configuration, the thermodynamic cycle, fuel selection, electrical distribution system, plant control, and air pollution control of NO[sub X], SO[sub 2], CO, particulates, non-methane hydrocarbons, opacity and ammonia.
The present invention provides an improvement in the art of combined steam turbine and gas turbine power plants of the type wherein the principal source of energy is a fluidized bed combustor fueled by coal. More specifically, the invention pertains to supplemental firing of the gas turbine cycle with a clean hydrocarbon fuel (CHF) at a high incremental efficiency to significantly increase overall plant efficiency.
The influence of heat treatment on the structure, mechanical properties and fracture peculiarities of high-strength (#alpha#+#beta#)-titanium alloy VT22 has been studied. It is ascertained that thermal cycling and subsequent high-temperature aging permit to reduce considerably crack growth rate. Thermal cycling is realized in the following mode: heating in #beta#-region, cooling and allowance in (#alpha#+#beta#)-region, heating in #beta#-region.
Cycling parameters (reversible specific capacity, first-cycle coulombic efficiency, accumulated irreversible capacity, and reversible capacity retention) of hybrid electrodes based on mechanical mixtures of a silicon nanopowder with KS6 and MAG-20 synthetic graphites and binders of varied nature were subjected to an integrated analysis in comparison with graphite electrodes.
Here, we provide the first study of prolactin (PRL) and prolactin receptor (PRLR) expression during the nonseasonal murine hair cycle, which is, in contrast to sheep, comparable with the human scalp...Full Text Available
The systems analyses and optimization studies performed in connection with a program to design and evaluate a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion and advanced technology in the hot gas cleanup system and gas turbines are presented. Details on the plant control system are included. (LCL)
A final report is presented on the design, environmental characteristics, performance and maintainability, and economic analysis of a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion, and advanced technology in the hot gas cleanup system and gas turbines. Experimental data on the performance of each of the major components are included. (LCL)
The use of nuclear reactors to provide electrical energy has shown considerable growth since the first nuclear plant started commercial operation in the mid 1950s. Although the main purpose of this paper is to review the fuel cycle capabilities in the United States, the introduction is a brief review of the types of nuclear reactors in use and the world-wide nuclear capacity.
Nuclear fuel cycle information in some countries that develop, supply or use nuclear energy is presented. Data about Argentina, Australia, Belgium, Netherlands, Italy, Denmarmark, Norway, Sweden, Switzerland, Finland, Spain and India are included. The information is presented in a tree-like graphic way. (C.S.A.).
We prove a uniqueness result for limit cycles of the second order ODE $\\ddot x + \\sum_{j=1}^{J}f_{j}(x)\\dot x^{j} + g(x) = 0$. We extend a uniqueness result proved in \\cite{CRV}. The main tool applied is an extension of Massera theorem proved in \\cite{GS}.
A guidance document on the instrumentation for monitoring and control of cycle chemistry for the steam-water circuits of fossil-fired and combined-cycle power plants was developed within the IAPWS Power Cycle Chemistry Working Group. This technical guidance document has been authorized by the International Association for the Properties of Water and Steam (IAPWS) at its meeting in Doorwerth, The Netherlands, 6-11 September, 2009, for issue by its Secretariat. The members of the IAPWS are: Britain and Ireland, Canada, the Czech Republic, Denmark, France, Germany, Greece, Japan, Russia, and the United States of America, and the associate members Argentina and Brazil, Italy, and Switzerland. In order to achieve suitable chemical conditions in steam-water circuits it is essential to establish reliable monitoring of key parameters on every plant. This enables the demonstration of operation within cycle ...
The detailed sequence stratigraphic analysis of the siliciclastic-dominated Late Cretaceous sediments (Aren Sandstone and Garumnian red beds, south central Pyrenees, Spain) reveals the repeating disposition of critical elements and controlling mechanisms of cycles and sequences. Our approach integrates (a) hierarchy of unconformity-bounded units, (b) physical expression of boundaries traceable from the continent to the basin, (c) featuring facies and depositional systems, (d) well log and seismic expression, and (e) driving basing-filling mechanisms. A comparison to other active basins is suggested in order to prove the validity beyond the regional scale. Four basin-wide transgressive facies cycles were identified and interpreted as third-order units. The transgressive phase of each cycle is represented by mixed shelf deposits, while regressive periods consists of complex delta systems. The cycles are ...
The Heat Cycle Research Program, which is being conducted for the Department of Energy, has as its objective the development of the technology for effecting the improved utilization of moderate temperature geothermal resources. To meet this objective, the program has as one of its goals to improve the performance of geothermal binary cycles to levels approaching the practicable thermodynamic maximum. In pursuit of this goal, tests are being conducted at the Heat Cycle Research Facility located at the DOE Geothermal Test Facility, East Mesa, California. The current testing involves the investigation of binary power cycle performance utilizing mixtures of non-adjacent hydrocarbons as the working fluids, with supercritical vaporization and in-tube condensation of the working fluid. In addition to the present test program, preparations are being made to investigate the binary cycle ...
The method of life-cycle assessment (LCA) has been applied to cars with different power trains. As an example, the results for greenhouse gas (GHG) emissions are presented. They show possibilities and limits for the reduction of these emissions in the transportation sector by means of advanced technology. (author) 2 figs., 4 refs.
To meet growth in the fast developing Pearl River Delta economic zone in China`s Guangdong province, a 270 MW oil-fired combined cycle at Foshan was built and commissioned in only 22 months from financial closure. This article describes the Foshan power station, specifications, design, procurement, construction and operating concerns. 5 figs.
The author describes the feasibility study on implementing 18-months fuel cycle project in Daya Bay NPP: content, steps and major results including objective determination, benefit/cost assessment, electric net demands investigation, risk assessment, technical targets
Korea Electric Power Corporation (Kepco) of South Korea has awarded Asea Brown Boveri Switzerland, a member of the ABB Group, a contract to supply the main equipment for two gas-fired combined-cycle power stations. News of the contract followed an announcement last year that Kepco will build a series of gas-fired power stations in the early 1990s to supply electricity to new housing and commercial areas being built in the Seoul-Incheon connurbation. (author).
The externally fired combined cycle is emerging as an economically viable repowering options for old non-competitive coal fired steam plants. This paper describes the initial operation of a pilot plant located at Kennebunk, Maine and the initial work on the repowering of a 48MW coal fired steam plant located in Warren, PA.
This article describes a new natural-gas-fired combined cycle cogeneration plant in Bellingham, Washington. The topics of the article include community impact, siting constraints, natural gas fuel, the flexibility provided by the steam turbine, the cooling tower and pumps, air-quality, noise, and cooling water system constraints, and community relations program.
The use of pressurised fluidized-bed coal combustion (fbc) in a combined cycle is seen as a most attractive technology for increasing the efficiency of electricity generation. The concept of pressurised fbc is described and the technical problems that are encountered in its operation and in limiting it to a gas turbine are discussed. Details are given of pilot plant facilities and current R and D programmes.
A number of binary geothermal cycles utilizing mixed hydrocarbon working fluids were analyzed with the overall objective of finding a working fluid which can produce low-cost electrical energy using a moderately low temperature geothermal resource. Both boiling and supercritical shell-and-tube cycles were considered. The performance of a dual-boiling isobutane cycle supplied by a 280/sup 0/F hydrothermal resource (corresponding to the 5MW pilot plant at the Raft River site in Idaho) was selected as a reference. To investigate the effect of resource temperature on the choice of working fluid, several analyses were conducted for a 360/sup 0/F hydrothermal resource, which is representative of the Heber resource in California. The hydrocarbon working fluids analyzed included methane, ethane, propane, isobutane, isopentane, hexane, heptane, and mixtures of those pure hydrocarbons. For comparison, two fluorocarbon refrigerants ...
A dual-boiling isobutane cycle was selected for the present 5-megawatt (5MW) Raft River Pilot Plant to utilize the lower-temperature geothermal resources (near 300F). This study represents a second effort directed toward the design of an improved binary geothermal electric plant suitable for utilization of the lower temperature resources. 7 refs.
An extended series of measurements at a conventional coal-fired boiler equipped with a wet-limestone flue gas desulfurization unit has shown that sulfate and sulfur dioxide removal efficiencies are dissimilar. The average SO2 scrubbing efficiency was 76% and was observed to decrease over a five-day operating cycle. Total sulfate scrubbing efficiency, averaging about 29%, was invariant throughout the operating cycle. (1 diagram, 3 tables)
The sulfur-iodine water-splitting cycle is characterized by the following three reactions: 2H/sub 2/O + SO/sub 2/ + I/sub 2/ ..-->.. H/sub 2/SO/sub 4/ + 2HI; H/sub 2/SO/sub 4/ ..-->.. H/sub 2/O + SO/sub 2/ + 1/2 O/sub 2/; and 2HI ..-->.. H/sub 2/ + I/sub 2/. This cycle was developed at General Atomic after several critical features in the above reactions were discovered. These involved phase separations, catalytic reactions, etc. Estimates of the energy efficiency of this economically reasonable advanced state-of-the-art processing unit produced sufficiently high values (to approx.47%) to warrant cycle development effort. The DOE contract was largely directed toward the engineering development of this cycle, including a small demonstration unit (CLCD), a bench-scale unit, engineering design, and costing. The work has resulted in a design that is projected to produce H/sub 2/ at prices not yet ...
The effect of accelerated thermal cycling on a joint between modified 9Cr-1Mo steel (Grade 91) and Alloy 800 welded with Inconel 82 and 182 filler material is discussed. This is part of a trimetallic transition joint involving Grade 91-Alloy 800-316LN austenitic stainless steel for steam generator application. It has been shown that, during thermal cycling following the typical post-weld tempering treatment at 760 deg. C for 2 h, no carbon diffusion occurs from the ferritic steel towards the weld metal. There is, in fact, a hardness increase at the ferritic steel/weld metal interface which is probably a result of work hardening. Carbon migration sets in only after unusually long post-weld heat treatments for 20 and 50 h at 760 deg. C followed by thermal cycling. Significantly, even under the most severe thermal cycling test conditions imposed, no cracking or oxide notching could be detected, thus ...
World-wide water scarcity, especially in the developing world, indicates a pressing need to develop inexpensive, decentralized small-scale desalination technologies which use renewable resources of energy. This paper provides a comprehensive review of the state-of-the-art in one of the most promising of these technologies, solar-driven humidification-dehumidification (HDH) desalination. Previous studies have investigated many different variations on the HDH cycle. In this paper, performance parameters which enable comparison of the various versions of the HDH cycle have been defined and evaluated. To better compare these cycles, each has been represented in psychometric coordinates. The principal components of the HDH system are also reviewed and compared, including the humidifier, solar heaters, and dehumidifiers. Particular attention is given to solar air heaters, for which design data is limited; and direct air heating ...
In the research of a more efficient, less costly, more environmentally responsible and less technically difficult method for generating electrical power from coal, `the Partially Gasified Coal Fired Combined Cycle with a CFBC with Different Speeds (DFBC)` is introduced by Tsinghua University. The high efficiency cycle includes gasification, compressed air heating in a fluidized bed immersed air heater followed by a combustor and the heat recovery of gas turbine exhausted gas used as the combustion of coal in the differential-velocity atmospheric circulating fluidized bed. Superheated steam is raised in the DFBC boiler. A preliminary analysis is made for the choice of combined cycle components. The computer program can be used to evaluate the design and off-design performance of the power plant. The simulation results show that the new system is a valuable coal fired combined cycle system for China, ...
The International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) was launched in the year 2000, based on a resolution by the IAEA General Conference (GC(44)/RES/21). INPRO intends to help to ensure that nuclear energy is available in the 21st century in a sustainable manner, and seeks to bring together all interested Member States, both technology holders and technology users, to consider, jointly, actions to achieve desired innovations. INPRO is taking care of the specific needs of developing countries. This IAEA publication is part of Phase 1 of INPRO. It intends to provide an overview on history, present situation and future perspectives of nuclear fuel cycle technologies. While this overview focuses on technical issues, nevertheless, the aspects of economics, environment, and safety and proliferation resistance are important background issues for this study. After a brief description about the INPRO project and an evaluation ...
The U.S. Department of Energy`s (DOE) Environmental Management Office of Science and Technology (EM-50) authorized studies on alternative systems for treating contact-handled DOE mixed low-level radioactive waste (MLLW). The on-going Integrated Thermal Treatment Systems` (ITTS) and the Integrated Nonthermal Treatment Systems` (INTS) studies satisfy this request. EM-50 further authorized supporting studies including this technology and subsystem cost sensitivity analysis. This analysis identifies areas where technology development could have the greatest impact on total life cycle system costs. These areas are determined by evaluating the sensitivity of system life cycle costs relative to changes in life cycle component or phase costs, subsystem costs, contingency allowance, facility capacity, operating life, and disposal costs. For all treatment systems, the most cost sensitive life cycle phase is the ...
Fully-fired combined cycle plants utilizing the high temperature gas turbine discharge as gas intake for a coal-fired steam generator were developed in the 1960's. Long-term experience and the excellent reliability statistics of the gas turbines of these plants have proven that the thermodynamic, economical and ecological advantages of combined cycle units over conventional units strongly suggest such plants for fossil-fuel applications. This paper describes the design and operation of these plants. Topics are Gersteinwerk Unit K combined-cycle power plant, plant design concept, design criteria and performance, gas turbines, steam generators, steam turbines, various modes of operation, typical plant start-up, environmental considerations, prototype plants and topping old steam turbine plants. It concludes that combined-cycle plants provide efficiencies over 45% with low NO/sub x/ emission and a ...
Freezing and thaw have an effect on soils, and the effect of the freeze-thaw cycle on soil covers used in the control of acid mine drainage was discussed in this poster presentation. The purpose of soil covers in cases involving acid mine drainage (AMD) is to reduce the exposure of tailings to oxygen which cause AMD. The effect of this freezing-thaw cycle on soft materials used in soil covers with capillary effect was studied. Some laboratory experiments were conducted to evaluate the properties of the moisture retention layer. The preliminary results were presented. The results indicated that the freeze-thaw cycle might affect the performance of soil covers in the long term, depending on the type of materials selected. Further research is undergoing. 26 figs.
Alloy 800 from three different commercial heats have been continuously cycled and cycled with a hold period at 922/sup 0/K. The starting microstructures of these heats reflects an inherently wide spectrum of possibilities for Alloy 800. The amounts and morphologies of the TiC and M/sub 23/C/sub 6/ carbides are different among the heats. During cycling, M/sub 23/C/sub 6/ forms intragranularly in a solution annealed heat. This precipitation contributes to the cyclic hardening. Both mill annealed heats of Alloy 800 are stable to carbide precipitation during cycling. The heat with the lower carbon content formed ..gamma..' during cycling but the volume fraction was too low to contribute to hardening. The inclusion of hold periods caused the dislocation substructure to become more diffuse in the mill annealed heats. The cyclic hardening was enhanced with the inclusion of the ...
Effects of dopant and coating carbon nanotube on anodic performance of Si were studied for metallic anode Li ion rechargeable battery with large capacity. Although the large Li intercalation capacity higher than 1500mAhg{sup -1} is exhibited on pure Si, it decreased drastically with increasing cycle number. Increasing the electrical conductivity by doping Cr or B is effective for increasing the initial capacity and the cycle stability of Si for Li intercalation. Coating semiconductive Si with the carbon nanotube by decomposition of hydrocarbon is effective for increasing the cycle stability, though the initial Li intercalation capacity slightly decreased. Conducting binder is also important for increasing the cycle stability and it was found that Li intercalation capacity higher than 1500mAhg{sup -1} can be sustained by using poly vinyliden fruolide. Consequently, reversible Li intercalation capacity of ...
High-resolution sequence stratigraphy taking base-level cycles as interface of reference was developed rapidly in recent years. Its greatest predominance lies in that it can be applied to multi-controled continental sedimentary basins and can effectively improve accuracy and distinguishability of sequence stratigraphy analysis. Principles of base-level cycles can also be applied to the research and practice of the exploration and exploitation of sandstone-type uranium deposits as they control the spatial distribution, porosity, the permeability and the sealing ability of sandstone and mudstone, and stacking patterns of strata configuration. Taking Dongsheng uranium deposits as an example, the application of base-level cycles to exploration and exploitation of sandstone uranium deposits was analyzed. It is suggested that favorable strata framework of sandstone and mudstone was developed very well in the fluctuation of ...
A number of binary geothermal cycles utilizing mixed hydrocarbon working fluids were analyzed with the overall objective of finding a working fluid which can produce low-cost electrical energy using a moderately-low temperature geothermal resource. Both boiling and supercritical shell-and-tube cycles were considered. The performance of a dual-boiling isobutane cycle supplied by a 280/sup 0/F hydrothermal resource (corresponding to the 5 MW pilot plant at the Raft River site in Idaho) was selected as a reference. To investigate the effect of resource temperature on the choice of working fluid, several analyses were conducted for a 360/sup 0/F hydrothermal resource, which is representative of the Heber resource in California. The hydrocarbon working fluids analyzed included methane, ethane, propane, isobutane, isopentane, hexane, heptane, and mixtures of those pure hydrocarbons. For comparison, two fluorocarbon refrigerants ...
This document is the Final Report for the project Introduccion de Mejoras Tecnologicas en el SISCOM II, or Improvements in SISCOM II Technology. It consists of a brief description of the activities carried out during the project, and several Annexes that explain in a deeper way each result. SISCOM II is the main telemetry system currently in use in the Spanish underground coal mining, but it was developed ten years ago and needed a technological update, which was the objective of this project. The aims of the project were: To develop Hardware and Software for the Out stations currently used (maintenance developments) To design new hardware and software, easier to use in the current and new applications of SISCOM II Both objectives were met, although not in the way originally intended. The main results were: In the field of old Out stations update: A new set of boards for the old Out stations was ...
The purpose of the current study was to evaluate the difference in prognostic factors between stage IB and II uterine cervical carcinoma patients treated with postoperative radiation therapy. Between May 1988 and May 1998, a total of 94 patients including 47 patients with stage IB and 47 patients with stage II uterine cervical carcinoma were treated with postoperative radiation therapy at Tokyo Metropolitan Komagome Hospital. All patients were treated with 10 MV X-rays using an anterior-posterior parallel opposed field which covered the whole pelvis. Fractionation was 2 Gy per day, five fractions per week, to a total dose of 50 Gy. The 5-year overall survival rates of stage IB and II were 89.4% and 79.3%, respectively. In multivariate analysis for all patients, lymph node status, histology, and surgical margin status were recognized as prognostic factors. Limited to stage IB patients, lymph node status was the only ...
The CDF II eXtremely Fast Tracker (XFT) is the trigger processor which reconstructs charged particle tracks in the CDF II central outer tracking chamber. The XFT tracks are also extrapolated to the electromagnetic calorimeter and muon chambers and are associated to electromagnetic clusters and muon stubs to generate trigger electron and muon candidates. The steady increase of the Tevatron instantaneous luminosity and the resulting higher occupancy of the chamber demanded an upgrade of the original system, which performed tracking only in the transverse plane of the chamber and was consequently affected by a significant level of fake tracks. In the upgraded XFT, tracking is reinforced by using additional data from the stereo layers of the chamber to reduce the level of fake tracks and to perform three-dimensional track reconstruction. A review of this upgrade is presented.
Feasibility Study-II examined a high-performance Neutrino Factory providing 1 x 10{sup 20} neutrinos per year aimed at a long-baseline detector. The Study was sponsored jointly by BNL and the Neutrino Factory and Muon Collider Collaboration ration (MC) and is based on a 1 MW proton driver operating at 24 GeV, i.e., an upgraded version of the AGS accelerator. Compared with the earlier FNAL-sponsored study (Feasibility Study-I), there is a sixfold improvement in performance. Here we describe details of the implementation of Study-II concepts and discuss their efficacy. Alternative approaches that will be pursued in follow-on R and D activities are also described briefly.
The distribution of the alkaline earth elements strontium and barium between the solid phases of phosphates of transition elements of group 4 and chloride melts was studied. The distribution coefficients of strontium and barium were found at T = 700-800/sup 0/C. Phosphates of the type NaM/sub 2//sup (IV)/(PO/sub 4/)/sub 3/, where M/sub (IV)/ represents titanium, zirconium, and hafnium, were used as the solid phases. It was established that there is an enrichment of the precipitates with the distributed components. The distribution coefficient depends on the nature of the solid phase and the temperature. It was suggested that M/sup (II)/ x M/sub 4//sup (IV)/(PO/sub 4/)/sub 6/ is formed in processes of distribution, where M/sup (II)/ represents Sr, Ba.
Raman and infrared spectroscopy of para-H{sub 2} to pressures in excess of 200GPa and to 8K using new ultrapure synthetic diamond anvils reveals numerous new vibrational excitations in the three high-pressure phases. Highly resolved Raman-active librons indicate differences in orientational ordering between phasesII and III, including evidence for changes within phaseII. The librons in phaseIII are strongly pressure dependent and reflect a substantial increase in ordering with pressure. Multiple vibrons in all three phases (I, II, and III) are observed. The results place new bounds on predicted crystal structures and dynamics of the dense molecular solid. {copyright} {ital 1997} {ital The American Physical Society}
The EXAFS spectra of the platinum(III) complexes Pt/sub 4/(OAc)/sub 10/(OH)/sub 2/ (I) and Pt/sub 4/ (OAc)/sub 4/(OH)/sub 8/(H/sub 2/O)/sub 2/ (II) have been investigated. It has been found by a curve-fitting method and with the aid of Fourier transformations that the shortest Pt-Pt distances are 2.61 A in complex I and 2.36 and 2.6 A in II. The values of the bond lengths obtained are consistent with the molecular structures proposed for complexes I and II, which contain skeletons of four platinum atoms in the form of a square or a rectangle, as well as with the known literature data on the lengths of Pt-Pt bonds in Pt(III) complexes.
Purpose Evaluation of the all-trans retinoic acid (t-RA) effects on in vitro maturation (IVM) and in vitro fertilization (IVF) of immature mouse oocytes in the presence and absence of granulosa cell monolayer. Methods Denuded oocytes isolated from mice ovaries and matured in IVM medium alone (Control I), IVM medium in the presence of granulosa cells (Control II), IVM medium with t-RA (Experimental I) and IVM medium simultaneously with t-RA and granulosa cells (Experimental II). After 24?h, matured oocytes were fertilized in T6 medium and their development was followed until the blastocyst stage. Metaphase II oocytes ploidy were evaluated by chromosome counting. Results The t-RA group compared to the control groups showed no obvious abnormalities. Additionally maturation and embryo developm...
The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples.
We study the localized tachyon condensation of non-supersymmetric orbifold backgrounds in their mirror Landau-Ginzburg picture. We first show that the R-charges of chiral primaries increase under the process of condensing the tachyon in the same chiral ring. Then, utilizing the existence of four copies of (2,2) worldsheet supersymmetry, we show that the minimal tachyon mass in twisted sectors increases in CFT and type 0 string and it plays the role of the c-function of the twisted sectors. We also study the GSO projection in detail and show that type II decays to only to type II while type 0 can mix with type 0 and II under the RG-flow.
Summary Background Sorafenib is an oral multikinase inhibitor that blocks cell proliferation via the ERK pathway and angiogenesis via the VEGF pathway. This phase II trial was conducted to determine the efficacy and tolerability of sorafenib for the treatment of patients with metastatic urothelial cancer (UC) who had not had prior chemotherapy for advanced disease. Patients and Methods Seventeen chemo-na?ve UC patients with adequate performance status and organ function were treated with sorafenib 400?mg twice daily on a continuous basis until progression or unacceptable toxicity. The primary endpoint was objective tumor response rate as measured by RECIST criteria. Secondary endpoints included rate of prolonged stable disease (>3?months), time to progression, median and 1?yr survival and ...
Ruthenium(II) and Iridium(III) polypyridyl complexes have been intensively investigated due to their use in energy conversion and light-emitting devices and materials for non-linear optics. Quantum mechanical computer simulations of molecules and materials have become increasingly popular in the scientific community. Along with experimental investigations, such computational analyses can provide complementary information on the electronic and optical properties of transition metal compounds of interest for optoelectronic applications. Here, we provide a unified review of recent work carried out on computational investigations of a large series of Ruthenium(II) and Iridium(III) polypyridyl complexes, discussing the relations between their electronic structure and optical properties and thei...
Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were either filled with air or with a molten mixture of sodium nitrate, potassium nitrate and an oxidizer. Low-cycle fatigue tests were carried out at 1200/sup 0/F and 650/sup 0/F by cycling the strain continuously between equal mangitude of tensile and compressive values at a rate of 4 x 10/sup -3/sec/sup -1/ until failure. The creep-fatigue tests were carried out at 1200/sup 0/F. The loading cycle differed from that of low-cycle fatigue testing only in the imposition of a hold at the peak compressive strain in each cycle. Cracks always initiated on the inner surface of the hollow specimen, and therefore, corrosive effects on crack propagation and initiation were controlled by the environment within the specimen cavity. In common with tests carried out ...
This third tome about energy systems completes the two previous ones by showing up advanced thermodynamical cycles, in particular having a low environmental impact, and by dealing with two other questions linked with the study of systems with a changing regime operation: - the time management of energy, with the use of thermal and pneumatic storage systems and time simulation (schedule for instance) of systems (solar energy type in particular); - the technological dimensioning and non-nominal regime operation studies. Because this last topic is particularly complex, new functionalities have been implemented mainly by using the external classes mechanism, which allows the user to freely personalize his models. This tome is illustrated with about 50 examples of cycles modelled with Thermoptim software. Content: foreword; 1 - generic external classes; 2 - advanced gas turbine cycles; 3 - evaporation-concentration, mechanical ...
Phase II Randomized Study of the Effect of Zoledronate Versus Observation on Bone Mineral Density of the Lumbar Spine in Patients Undergoing Risk-Reducing Excision of Both Ovaries (GOG-0215). See the protocol summary.
Sensory rhodopsins (SRs) belong to a subfamily of heptahelical transmembrane proteins containing a retinal chromophore. These photoreceptors mediate the cascade of vision in animal eyes and phototaxis...Full Text Available
We have previously observed that auxin can act as a repressor of the wound-inducible activation of a chimeric potato proteinase inhibitor II-CAT chimeric gene (pin2-CAT) in transgenic...Full Text Available
The Ty transposable elements of Saccharomyces cerevisiae form a heterogeneous family within which two broad structural classes (I and II) exist. The two classes differ by two large substitutions and...Full Text Available
Molecular Misreading (MM) is the inaccurate conversion of genomic information into aberrant proteins. For example, when RNA polymerase II transcribes a GAGAG motif it synthesizes at low frequency RNA...Full Text Available
... NE Mall Room B-607, EPA Headquarters, 401 M ... formally adopted and initiated a joint strategy for ... CLI kick-off Partner and Task Force meeting. ...
Highly polymorphic genes with central roles in lymphocyte mediated immune surveillance are grouped together in the major histocompatibility complex (MHC) in higher vertebrates. Generally, across vertebrate...Full Text Available
Thin film solar cells and solar cell testing - photovoltaic cells, radiation damage to cadmium sulfide solar cells, and airplane testing of solar cells
The article is divided into three sections: (i) an overview of the main ethical models in public health (theoretical foundations); (ii) a summary of several published frameworks for public health ethics...Full Text Available
The effect of Escherichia coli lipopolysaccharide (LPS) on the expression of major histocompatibility complex (MHC) class II molecules by bovine mammary macrophages was examined. The ability of LPS-treated...Full Text Available
The world's oceans contain a complex mixture of micro-organisms that are for the most part, uncharacterized both genetically and biochemically. We report here a metagenomic study of the marine planktonic...Full Text Available
The clinical management of adults with low-grade gliomas (LGGs) remains a challenge. There is no curative treatment, and management of individual patients is a matter of deciding optimal timing as well...Full Text Available
Peptide toxins with high affinity, divergent pharmacological functions, and isoform-specific selectivity are powerful tools for investigating the structure-function relationships of voltage-gated...Full Text Available
Feb 23, 2011 ... THEMIS-D: The Solid State Telescope (SST) measures the incoming ... Each single sensor covers an angle of 36 degrees. .... The five small satellites were launched together on a Delta II rocket and they carry identical ...
New Schiff base derivatives (L1 and L2) were prepared by the condensation of 2-hydroxy-3-methoxybenzaldehyde (o-vanillin) and 3-hydroxy-4-methoxybenzaldehyde (iso-vanillin) with 5-methylfurfurylamine. Two new complexes [Ni(L1)2] and [Cu(L1)2] have been synthesized with bidentate NO donor Schiff base ligand (L1). The Ni(II) and Cu(II) atoms in each complex are four coordinated in a square planar geometry. Schiff bases (L1 and L2) and complexes [Ni(L1)2] and [Cu(L1)2] were characterized by elemental analyses, FT-IR, UV-vis, mass and 1H, 13C NMR spectroscopies. The crystal structures of the ligand (L2) and complexes [Ni(L1)2] and [Cu(L1)2] have also been determined by using X-ray crystallographic technique.
Potassium dichlorido(l-prolinato)platinate(II), K[PtCl"2(l-pro"?"H)] (1), and chlorido(dimethyl sulfoxide)(l-prolinato)platinum(II), [PtCl(l-pro"?"H)(dmso)] (2), were synthesized by ligand substitution reactions. Both complexes were characterized by ^1H, ^1^3C, and ^1^9^5Pt NMR spectroscopy, elemental analysis, and HR-ESI-MS. The molecular structures of 1 and 2 were determined by single crystal X-ray diffraction, proving bidentate coordinated l-prolinato ligand and SP-4-4 configuration of 2a. With the help of DFT calculations stability of possible isomers of 1 and 2 was studied. A considerable difference in the in vitro cytotoxicity of 1 versus 2a (exchange of one chlorido ligand by dmso) against four human cancer cell lines was found.
Six related Staphylococcus phages spontaneously produced various abnormal head and tail structures: (i) giant capsids which were tailed and apparently contained nucleic acid; (ii) regular and irregular...Full Text Available
Sedentary adult males with spinal lesions, all habitual wheelchair users, were allocated to exercise (n = 11) and control (n = 4) groups. A Cybex II dynamometer was used to assess peak power, average...Full Text Available
Platinum(II) complexes (1-4) with bidentate N,Nprime-ligands, O,Oprime-dialkyl esters (alkyl = ethyl, n-propyl, n-butyl and n-pentyl), of (S,S)-ethylenediamine-N,Nprime-di-2-(4-methyl)pentanoic acid were synthesized and characterized by IR, 1H NMR and 13C NMR spectroscopy and elemental analysis. DFT calculations were performed for the complexes and it was found that only one diastereoisomer could be formed. Cytotoxic activity of complexes 1-4 was determined against chronic lymphocytic leukemia cells (CLL) and compared to the activity of ligand precursors L12HCl-L42HCl and corresponding palladium(II) complexes, [PdCl2L] (L = L1-L4). The complexes were found to exhibit significantly higher antitumor activities than cisplatin on CLL cells. Cytotoxic effect of platinum(II) complexes on CLL cel...
Spectral line intensity data are presented for ionized hydrogen regions in the giant spiral galaxy M101. The influence of interstellar extinction is assessed and electron temperatures of the gas clouds are derived.
A rapid and sensitive method for the separation and determination of titanium and iron in thiocyanate system has been developed. The extractability of Ti(II) by high molecular weight (HMWA) in organic solvent (HCl/sub 3/) and its separation from Fe(III) was examined. The yellow coloured complex of Ti(II)-SCN in quantitatively extracted into the organic phase containing tribenzyl tribenzylamine (TBA) - a high molecular weight amine, whereas the blood red coloured complex of Fe(III)-SCN formed under the same conditions get separated in the aqueous phase. On the basis of the selective extractability, a method has been developed for the separation as well as simultaneous determination of Ti(II) and Fe(III) in presence of many other elements. The molar extinction coefficients were found to be 1.9 x 10/sup 5/ l mol/sup -1/ cm/sup -1/ and 1.11 x 10/sup 5/ l mol/sup -1/ cm/sup -1/ respectively for Ti(II) and ...
BackgroundPeroxiredoxins (Prxs) have recently been suggested to have a role in tumorigenesis.MethodsWe studied the expression of Prx I-VI and their...Full Text Available
THEMIS-A: The Solid State Telescope (SST) measures the incoming intensity ... units (heads), each SST unit has two pairs of opposing ion and electron sensors. .... The five small satellites were launched together on a Delta II rocket and they ...
The planned spallation source can be of considerable significance for biomedical basic research and for clinically relevant diagnostic and therapeutic applications. The following gives a brief description and explanations for its possible use in clinical medicine: I. Treatment of Malignant Tumors II. Production of Isotopes for Biochemical Investigations in Living Organisms for Diagnostic Purposes.
We designed a multicenter study to compare tobramycin/clindamycin to imipenem/cilastatin for intra-abdominal infections. We included the Acute Physiology and Chronic Health Evaluation (APACHE II) index...Full Text Available
SUMMARYReplication timing is frequently discussed superficially in terms of its relationship to transcriptional activity via chromatin structure. However, so little is known about...Full Text Available
BackgroundThe Class II DNA transposons are mobile genetic elements that move DNA sequence from one position in the genome to another. We have previously demonstrated that the naturally...Full Text Available
The results of the radon concentration measurements in dwellings in Belgrade were shown in this paper. The measurements were done using long term method with diffusion cups equipped with solid state nuclear track detector LR-115-II or CR-39. (author).
The Gordon Research Conference (GRC) on ROCK DEFORMATION was held at II Ciocco from 5/19/02 thru 5/24/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.
Human longevity is in part genetically determined, and the insulin/IGF-1 signal transduction (IIS) pathway has consistently been implicated. In humans, type 2 diabetes is a frequent disease that results...Full Text Available
PurposePlatinum and taxane compounds have demonstrated activity in uterine carcinosarcoma (malignant mixed Mullerian tumor). Ifosfamide plus paclitaxel is the regimen with established...Full Text Available
We obtain the radial Dirac equations for the Plebanski metric and transform these equations into one-dimensional wave equations. Finally we conclude with the result that the electron and the neutrino fields are not superradiant.
BackgroundThe lack of adequate randomized clinical trials (RCT) has hindered identification of new therapies that are safe and effective for patients with primary focal segmental...Full Text Available
Theoretically, the outcome of World War II in Europe hung in the balance as the Allies poured onto the Normandy beachhead. Following the June 6, 1944 invasion, the Allies continue to come ashore, massively building up men and material inside the beachhead...
This report discusses the following topics on superconductivity: nonlinearities in hard superconductors such as surface impedance of a type II superconductimg half space and harmonic generation and intermodulation due to alternating transport currents; and nonlinearities in superconducting weak links such as harmonic generation by a long Josephson Junction in a superconducting slab.
A study of the joint evolution of the normal- and neutron-star components of massive binaries opens with a classification scheme and the analytic expressions to be applied in Paper II for computer simulation of the observable properties of such systems.
The mechanism of cytokinesis has been difficult to define because of the short duration and the temporal-spatial dynamics involved in the formation, activation, force production, and disappearance of...Full Text Available
Endosomal sorting complexes required for transport (ESCRTs) are heteromeric protein complexes required for multivesicular body (MVB) morphogenesis. ESCRTs I, II, III and III-associated are ubiquitous...Full Text Available
Obesity and metabolic syndrome result from excess calorie intake and genetic predisposition and are mechanistically linked to type II diabetes and accelerated body aging; abnormal nutrient and insulin...Full Text Available
NUPEC has carried out hydrogen mixing tests to investigate hydrogen distribution behavior within a model containment and to provide a set of experimental data for validation of severe accident analysis codes.
SummaryThe general transcription factor TFIID is a large multi-subunit complex required for the transcription of most protein-encoding genes by RNA polymerase II. Taking advantage...Full Text Available
Type II collagen-induced arthritis (CIA) in mice is an autoimmune experimental model for rheumatoid arthritis. Susceptibility to CIA is associated with certain major histocompatibility complex class...Full Text Available
Mammals possess multiple insulin-like growth factor (IGF) binding proteins (IGFBPs), and related proteins, that modulate the activity of insulin/IGF signalling (IIS), a conserved neuroendocrine signalling...Full Text Available
Rationale: Human data suggest that the incidence of acute lung injury is reduced in patients with type II diabetes mellitus. However, the mechanisms by which diabetes confers protection...Full Text Available
The visible absorption spectra of 1,4-(dihydroxy)-9,10-anthraquinone and of Co(II), Ni(II), Cu(II) and Zn(II) chelates have been studied in different organic solvents. This system provides a model for the anthracycline antibiotics and their metal chelates. The band structure of the spectrum has been determined using the second and fourth derivatives of the spectrum. The visible absorption band of the parent molecule can be assigned to a single electronic state with a reduced dipole moment in the excited state; structure in this band is ascribed to two overlapping vibrational progressions. In contrast, the dianion (hydroxy protons removed) shows a single electronic state with an increased dipole moment in the excited state; structure in this band can be assigned to a single vibrational progression. All of the metal chelates show spectra which are similar in appearance to that of the dianion although the ...
The cytokine interleukin-7 (IL-7) has essential growth activities that maintain the homeostatic balance of the immune system. Little is known of the mechanism by which IL-7 signaling regulates metabolic...Full Text Available
The major activities of the various Institute's departments are highlighted. The following departments are included: (i) Tokamak; (ii) Pulse plasma systems; (iii) Thermal plasma; (iv) Materials engineering; (v) Laser plasma; and (vi) Optical diagnosis. (P.A.)
The importance of a properly functioning and well-balanced immune system for maintaining health has become strikingly evident over the past decades. Roughly since World War II, there has been an apparent...Full Text Available
An aqueous house dust mite extract was separated by SDS-PAGE and transferred to nitrocellulose membranes by Western Blotting. Two major allergens, Der pI and Der pII associated with the mite faeces...Full Text Available
Several examples of the 14-membered, para-bridged ring system of the cyclopeptide alkaloids have been synthesized via an active ester cyclization. The yield of monomeric cyclopeptide varied from 1 to 33% and was affected by the amino acid substitution pat...
During Phase II multi-junction solar cell will be grown on the large grain thin film produced during Phase I on flexible/low cost metal foil substrate. ...
The various steps of gas treatment in the Sasol II coal liquefaction plant are discussed: CO/sub 2/ removal, separation of the hydrocarbon fractions and the recirculated hydrogen by low-temperature decomposition, production of pure hydrogen by alternating pressure absorption.
Microarray data has a high dimension of variables but available datasets usually have only a small number of samples, thereby making the study of such datasets interesting and challenging. In the task...Full Text Available
We present results of near--IR long-slit spectroscopy in the J and K bands of the Seyfert 2 galaxies NGC 2110 and Circinus, investigating the gaseous distribution, excitation, reddening and kinematics. In NGC 2110, the emission line ratio [FeII]/Pa beta increases towards the nucleus (to ~ 7). The nuclear [Fe II]1.257 (microns) and Pa beta lines are broader (FWHM ~ 500 km/s) than the H2 (2.121) line (FWHM ~ 300 km/s). Both these results suggest that shocks, driven by the radio jet, are an important source of excitation of [Fe II]. The H2 excitation appears to be dominated by X-rays from the nucleus. In Circinus, both [FeII]/Pa beta and H2/Br gamma decrease from ~ 2 at 4 arcsec from the nucleus to nuclear values of ~ 0.6 and ~ 1, respectively, suggesting that the starburst dominates the nuclear excitation, while the AGN dominates the excitation further out (r > 2 arcsec). For both galaxies, the gaseous ...
Biosorption of lead(II) ions from aqueous solution onto the seed husk of Calophyllum inophyllum was investigated in a batch system. Equilibrium, thermodynamics and kinetic studies were conducted by considering the effects of pH, initial metal ion concentration, contact time, and temperature. The results showed that the uptake of the metal ions increased with increase in initial metal ion concentration. The pH for optimum adsorption was 4 for the Pb(II) ions (q=4.86mg/g and 97.2% adsorption). Langmuir isotherm described the biosorption of Pb(II) ions onto the biomass (R^2=0.9531) better than the Freundlich model (R^2=0.7984), and the Temkin model (R^2=0.8761). Biosorption kinetics data obtained for the metal ions sorption were fitted using pseudo-first-order and pseudo-second-order. It was ...
The biosorption of copper(II) ions from aqueous solution by Tectona grandis L.f. was studied in a batch adsorption system as a function of pH, metal ion concentration, adsorbent concentration and adsorbent size. The biosorption capacities and rates of copper(II) ions onto T. grandis L.f. were evaluated. The Langmuir, Freundlich, Redlich-Peterson and Temkin adsorption models were applied to describe the isotherms and isotherm constants. Biosorption isothermal data could be well interpreted by the Langmuir model with maximum adsorption capacity of 15.43 mg/g of copper(II) ion on T. grandis L.f. leaves powder. The kinetic experimental data properly correlated with the second-order kinetic model. Various thermodynamic parameters such as {delta}G{sup o}, {delta}H{sup o}, and {delta}S{sup o} were calculated indicating that this system was a spontaneous and exothermic process.
Endometrial biopsies were taken for histological assessment from 97 cows which calved in a commercial dairy herd between April and August 1984. The main objectives of this study were to analyze the...Full Text Available
The electroreduction process of Zr(IV) was studied at molybdenum electrode in LiCl-KCl-K2ZrF6 molten salt. The transient electrochemical techniques, such as cyclic voltammetry and chronopotenimetry were used. The experimental results showed that the electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both diffusion-controlled process. In the 773-973K range, the diffusion coefficients of Zr(ii) and Zr(IV) were determined: DZr(II)=0.15567exp{-69.65x10^3RT(K)}cm^2/s, DZr(IV)=1.09x10^-^4exp{-44.39x10^3RT(K)}cm^2/s. The activation energy values for the diffusion process were 69.65kJ/mol and 44.39kJ/mol, respectively.
Ligand exchange of hydrated metal complexes is common in chemical and biological systems. Using the ultrafast T-jump, we examined this process, specifically the transformation of aqua cobalt (II) complexes...Full Text Available
Purpose.The hypothesis that drivers with homonymous hemianopia (HH) would take a lane position that increased the safety margin on their blind side was tested with a driving simulator.Methods.Twelve...Full Text Available
Uncoupling protein 2 (UCP2) maps to a region on distal mouse chromosome 7 that has been linked to the phenotypes of obesity and type II diabetes. We recently reported that UCP2 expression is increased...Full Text Available
Systemic administration of lipopolysaccharide (LPS), which causes endotoxemia and systemic inflammation, has been reported to induce expression of the gene for type II inducible nitric oxide synthase...Full Text Available
In order to decrease tritium exposure to workers, the ratio of which is up to 40% of total exposure, tritium removal facility is getting to be one of the considerable parameters in Korea, due to the next CANDUs to be operated at Wolsung NPP. For investiga...
Realization that dental caries is a reversible, dynamic biochemical event at a micron level has changed the way the profession recognizes the caries disease and the caries lesion. The diagnosis of dental...Full Text Available
In this paper we discuss the effect on the emittance of the residual dispersion in the insertion devices. The dispersion in the straights could be generated by the lattice error, trim dipole, and insertion device. The effect on the emittance is examined, and the dispersion tolerances are given for the NSLS-11.
Crystalline bis(O,O'-di-sec-butyldithiophosphato)platinum(II) was prepared and studied by means of 13C, 31P CP/MAS NMR spectroscopy and single-crystal X-ray diffraction. The unit cell of the platinum(II) compound is comprised of one centrosymmetric mononuclear molecule [Pt{S2P(O-sec-C4H9)2}2], in which the dithiophosphate groups display structural equivalence in both 31P NMR and XRD data. A pair of the dithiophosphate ligands exhibit the same S,S'-bidentate chelating structural function and form two planar four-membered chelate rings, [PtS2P], in this molecule. The planar configuration of the [PtS4] chromophore in structure 1 is governed by the dsp2-hybrid state of platinum(II). The structural states of the dithiophosphate groups in two different samples of complex 1 (one crystallised from...
BackgroundThe rate of emergence of human pathogens is steadily increasing; most of these novel agents originate in wildlife. Bats, remarkably, are the natural reservoirs of many...Full Text Available
This report documents the operation, maintenance, calibration, data acquisition and data reduction at the Chalk Point Meteorological Station for the period November 15, 1978 through November 15, 1979. Climatological data summaries for each month and calib...
This book contains over 20 selections. Some of the titles are: Continuum damage mechanics studies on the dynamic fracture of concrete; Dynamic compressive strength of cementitious materials; Rate-sensitivity of mode I and mode II fracture concrete; and An impact damage model of concrete.
Benzodiazepine withdrawal anxiety is associated with potentiation of α-amino-3-hydroxy-5-methyl-4-isoxazolepropionate receptor (AMPAR) currents in hippocampal CA1 pyramidal...Full Text Available
BackgroundThere is no consensus as to the prognostic model for brachytherapy of tongue carcinoma. This study was designed to evaluate the prognostic factors for local control based...Full Text Available
The reserves and the mine are described. Planned capacity is 27.5 million tonnes per year of coal for the Sasol II and Sasol III liquefaction plants. There will be 7 longwall faces, 15 entry workings with shotfiring, and 19 entries with continuous miners.
In a study where the removal of heavy metals from wastewater is the primary aim, the biosorption of heavy metals onto biosolids prepared as Pseudomonas aeruginosa immobilized onto granular activated carbon was investigated in batch and column systems. In the batch system, adsorption equilibriums of heavy metals were reached between 20 and 50 min, and the optimal dosage of biosolids was 0.3 g/L. The biosorption efficiencies were 84, 80, 79, 59 and 42 % for Cr(VI), Ni(II), Cu(II), Zn(II) and Cd(II) ions, respectively. The rate constants of biosorption and pore diffusion of heavy metals were 0.013-0.089 min{sup -1} and 0.026-0.690 min{sup -0.5}. In the column systems, the biosorption efficiencies for all heavy metals increased up to 81-100 %. The affinity of biosorption for various metal ions towards biosolids was decreased in the order: Cr = Ni > Cu > Zn > Cd. (Abstract Copyright ...
The potential of the dried yeast, wild-type Schizosaccharomyces pombe, to remove Ni(II) ion was investigated in batch mode under varying experimental conditions including pH, temperature, initial metal ion concentration and biosorbent dose. Optimum pH for biosorption was determined as 5.0. The highest equilibrium uptake of Ni(II) on S. pombe, q e, was obtained at 25??C as 33.8?mg?g?1. It decreased with increasing temperature within a range of 25?50??C denoting an exothermic behaviour. Increasing initial Ni(II) concentration up to 400?mg?L?1 also elevated equilibrium uptake. No more adsorption took place beyond 400?mg?L?1. Equilibrium data fitted better to Langmuir model rather than Freundlich model. Sips, Redlich?Peterson, and Kahn isotherm equations modelled the investigated system with a...
BackgroundHigh intake of sugar-sweetened beverages in childhood is linked to increased risk of obesity and type II diabetes later in life. Using three nationally representative surveys...Full Text Available
Alterations in basement membrane components, notably proteoglycans, in a rat model of polycystic kidney disease have been investigated. Rats were fed phenol II (2-amino-4-hydroxyphenyl-5-phenyl thiazole)...Full Text Available
The Federal Highway Administration (FHWA) has put a high priority on the use of existing dynamic message signs (DMS) to provide travel time estimates to the public. The Oregon Department of Transportation (ODOT) has three DMS in the Portland metropolitan ...
This report made for the Swiss Federal Office of Energy (SFOE) discusses the conception, planning and construction of an easy-to-operate pilot heating plant that uses chicken litter as its fuel. The plant, which is installed at a chicken farm in Boesingen, Switzerland, produces 250 - 350 kW and not only supplies heat for two chicken sheds and two households, but also provides energy for a drying plant in summer. The results of measurements made on emissions are discussed and, within the framework of an eco-balance analysis, comparisons are made between the direct use of the droppings as manure or as a fuel. The cost-effectiveness of the plant is examined and the influence of plant size and other factors discussed. Further, legal questions concerning the use of chicken litter as a fuel for heating installations are discussed; the use of the droppings as a fuel is not foreseen in the legislation concerning water protection and airborne emissions of pollutants. Although normally this type ...
The protein kinase CK2 (formerly casein kinase II) is thought to be involved in light-regulated gene expression in plants because...Full Text Available
Pharmacologic or genetic deletion of components of the renin-angiotensin system leads to postnatal kidney injury, but the roles of these components in kidney development are unknown. To test the hypothesis...Full Text Available
Aug 15, 2002 ... In Section II, we describe the routing and transceiver power model used ... In our power model, we assume a certain non-zero minimum level of ...
PurposeWe previously reported a randomized phase II clinical trial combining a poxvirus-based vaccine encoding PSA with radiotherapy in patients with localized prostate...Full Text Available
We describe the Phase II HapMap, which characterizes over 3.1 million human single nucleotide polymorphisms (SNPs) genotyped in 270 individuals from four geographically diverse populations and...Full Text Available
We proposed a faster pedigree-based generalized multifactor dimensionality reduction algorithm, called PedG-MDR II (PII), to detect gene-gene interactions underlying complex traits. Inherited...Full Text Available
...Department of Environmental Control to ASARCO Incorporated. (B) Amended Administrative...Department of Environmental Control to ASARCO Incorporated. (C) Second Amended...Department of Environmental Control to ASARCO Incorporated. (ii) Additional...
...capacity, and ownership of all planned and existing onshore pipelines, storage facilities, refineries, petrochemical...will be served by the port, including: (i) Onshore pipelines; (ii) Storage facilities; (iii)...
...competent person shall inspect haulage equipment before each shift. (ii...used. (2) Powered mobile haulage equipment shall have suitable means of... (3)(i) Power mobile haulage equipment, including trains, shall...
Presently, industrial maturity can be claimed for two fuel cycle strategies, viz. the 'Once Through Fuel Cycle' (OTC), and the 'Reprocessing Fuel Cycle' (RFC) in which plutonium and very limited uranium quantities are being recycled. It is helpful to recall some key data that set the stage for any discussion of fuel cycle options: 1. Worldwide, the annual spent fuel discharge is in the range of 10500-11000 t heavy-metal (HM), while the industrial reprocessing capacity amounts to #approx# 5000 t HM (OECD NUCLEAR ENERGY AGENCY, Accelerator-driven Systems (ADS) and Fast Reactors (FR) in Advanced Nuclear Fuel Cycles: a Comparative Study, Paris, 2002). Hence, less than 1/2 of the discharged spent fuel can be processed. 2. Worldwide, the cumulative inventory of stored spent fuel is estimated to be #approx# 190000 t HM, and the amount of reprocessed spent fuel is estimated to be #approx# ...
Two US DOE projects in the Pacific Northwest offer unique on-the-scene training opportunities at sodium-cooled fast-reactor plants: the Fast Flux Test Facility (FFTF) near Richland, Washington, which has operated successfully in a wide range of irradiation test programs since 1980; and the Experimental Breeder Reactor II (EBR-II) near Idaho Falls, Idaho, which has been in operation for approximately 20 years. Training programs have been especially designed to take advantage of this plant experience. Available courses are described.
Volume II of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the potentiometric data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
A computational procedure is proposed to perform uncertainty analysis for the calculation of the isotopic inventory and radiological quantities obtained as a linear function of it, due to uncertainties in the activation cross sections. The method is applied to determine the uncertainty of the calculated shallow burial index (SBI) from activated type 304 stainless steel (SS) in the most neutron-exposed zone of the HYLIFE-II vessel structure. Results are obtained by means of an element-by-element study. Some other types of steel are also investigated for comparison purposes. The SS304 is confirmed to be the most promising steel option. 16 refs., 2 tabs.
The properties of a helium film on the surface of solid parahydrogen are investigated. It is shown that wetting of the solid hydrogen by the liquid helium occurs. The transport velocities along the He II film on the solid parahydrogen surface are measured in broad temperature, film height, and level difference ranges. It is shown that the transport velocity in this case has the least value as compared with its value on other substrates. The thickness of the helium-saturated film is determined on the solid hydrogen surface on the basis of the data obtained, and the value is in good agreement with the results of a computation performed within the framework of the Frenkel' theory.
The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.
...225J Einstein, Oppenheimer, Feynman: Physics in the 20th Century Fall 2002 8.231 Physics of Solids I Fall 2002 8.251 String Theory for Undergraduates Spring 2003 8.261J Introduction to Computational Neuroscience Spring 2002 8.282J Introduction to Astronomy Spring 2003 8.321 Quantum Theory I Fall 2002 8.322 Quantum Theory II Spring 2003 8.323 Relativistic Quantum Field Theory I Spring 2003 8.324 Quantum Field Theory II ...
The mass distribution of the Sombrero Galaxy, NGC 4594, is calculated in order to investigate the suspicion that the rotational velocity of the galactic gas does not measure the circular velocity in the galaxy. It is shown that the H II rotation velocities are much less than circular in the central 35 arcsec of the galaxy, and that the suspicion is correct. Thus, the H II rotation velocities cannot be used to measure the mass distribution. The absorption-line rotation curve is used to derive the mass distribution, and it is found that the M/L ratio is nearly constant. It is concluded that the visible matter is self-gravitating at least in the central 180 arcsec. 44 references.
The main results of earlier work by the author, Sushko, and Khoruzhii describing the algebraic structure of quantum-field systems with (discrete) vacuum superselection rules are generalized to the large class of Wightman theories with essentially self-adjoint field operators (a very strong restriction was imposed on the theory, namely, that the polynomial Op algebra of the Wightman fields /rho/ belongs to the class II, i.e., /rho/ /sub s'/ =/rho/ /sub w'/). It is also shown that the field Op algebra of a Wightman theory with discrete vaccum superselection rule possesses a class II extension.
The purpose of this paper is to describe a technique of forced surgical rotation of the mandible used in skeletal Class II patients with deep bite and prominent chin. Posterior occlusal composite onlays combined with preoperative orthodontic treatment without anterior intrusion increase the posterior rotational component of the surgical mandibular advancement, when removed during operation. This manoeuvre allows for the surgical closure of the posterior open bite, while anteriorly the deep bite is opened. This technique avoids bimaxillary rotation surgery with dorsal impaction in mild to moderate cases. In any case, a chin setback osteotomy with compromised aesthetics can be avoided.
This handbook breaks down the complex field of nuclear reactor calculations into major steps. Each step presents a detailed analysis of the problems to be solved, the parameters involved, and the elaborate computer programs developed to perform the calculations. This book bridges the gap between nuclear reactor theory and the implementation of that theory, including the problems to be encountered and the level of confidence that should be given to the methods described. Volume II: Monte Carlo Calculations for Nuclear Reactors. In-Core Management of Four Reactor Types. In-Core Management in CANDU-PHW Reactors. Reactor Dynamics. The Theory of Neutron Leakage in Reactor Lattices. Index.