International Nuclear Information System (INIS)

The present work summarizes efforts on the simulation of natural convection cooling within the IFMIF target and test cell. The simulations have been performed with the STAR-CD code using the k-#omega# high-Reynolds number turbulence model. A dedicated thermohydraulic model has been devised including Lithium loop components. Nuclear heat production has been calculated by the Monte-Carlo code McDeLicious for different parts of the target and test cell walls and was used as input for the STAR-CD simulations. Helium atmospheres at several pressures from 0.1 to 10"-"5 MPa have been investigated. In order to limit the maximum temperature of the concrete walls to 80 deg. C it was necessary to add thermal insulation layers to the hot Lithium loop surfaces and a conceptual system of two cooling layers in different depths of the concrete walls.

International Nuclear Information System (INIS)

Current trends in nuclear power generation (and particularly in pressurized water reactors) are toward plant life extension and extended fuel burnup. A higher heat generation rate can induce local boiling regimes at the fuel rod surface in the hottest channels of the core, which can strongly modify the chemical environment of the cladding and influence the oxidation rate of zirconium alloys. Tests performed in out-of-pile loops under severe chemical and thermal-hydraulic conditions (nucleate boiling, higher lithium contents compared to PWRs) reveal two important phenomena: an increase of the oxidation rate of Zircaloy-4 cladding materials in 'high' lithiated environments; an enrichment of the chemical additives in the primary water (boron, lithium) at the surface of the cladding under nucleate boiling conditions. The latter phenomenon, also called 'hideout effect', is mainly controlled by some thermal hydraulic parameters ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

CERN Document Server

If two loops are isomorphic, then it is shown that their holomorphs are also isomorphic. Conversely, it is shown that if their holomorphs are isomorphic, then the loops are isotopic. It is shown that a loop is a Smarandache loop if and only if its holomorph is a Smarandache loop. This statement is also shown to be true for some weak Smarandache loops(inverse property, weak inverse property) but false for others(conjugacy closed, Bol, central, extra, Burn, A-, homogeneous) except if their holomorphs are nuclear or central. A necessary and sufficient condition for the Nuclear-holomorph of a Smarandache Bol loop to be a Smarandache Bruck loop is shown. Whence, it is found also to be a Smarandache Kikkawa loop if in addition the loop is a Smarandache A-loop with ...

International Nuclear Information System (INIS)

An attempt is made to estimate the lithium reserve (the economically recoverable lithium) for the tritium breeding in D-T fusion reactors and other uses. Similar development patterns for fusion energy and fission energy are assumed to estimate the future lithium requirements. These requirements are grouped into three categories; the commercial uses, the lithium batteries for electric cars, and the fusion reactor uses. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

This short paper (abstract) describes the characteristics and performances of prototypes of ultra-thin lithium micro-batteries (thickness < 0.2 mm) which can be incorporated into microelectronic circuits. (J.S.)

International Nuclear Information System (INIS)

Analysis of results of an investigation into the structure of lithium salt aqueous solutions is presented. An anomaly in lithium ion behaviour in solutions at the structural level is noted. 40 refs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

The in-situ observation of dendritic growth in lithium/polymer electrolyte-LiTFSI/lithium battery cells shows that dendrites grow up with about the same rate as anion migration. Memory effects have been evidenced in cycling experiments and limit the dendrites length. An overall movement of the electrolyte due to variations of electrolyte concentration in the vicinity of the electrodes has been observed too. (J.S.) 13 refs.

Energy Technology Data Exchange (ETDEWEB)

Radiation Damage Calculations for the FUBR and BEATRIX Irradiations of Lithium Compunds in EBR-II and FFTF

Energy Technology Data Exchange (ETDEWEB)

Research investigating applicability of lithium salts for solid electrolyte batteries was described. The studies included determinations of lithium ion conductivities in solid electrolyte systems based on Li4SiO4, LiTi2(PO4)3, and ceramic materials. Research on all solid state lithium cells utilizing TiS2 NiPS3 electrodes was also reported.

Energy Technology Data Exchange (ETDEWEB)

The membrane transport of the two stable lithium isotopes, {sup 6}Li and {sup 7}Li, by erythrocytes has been studied using a dual channel atomic absorption spectroscopic technique. {sup 6}Li appears to be taken up preferentially to {sup 7}Li, in the ratio of 10 to 40%, depending on the concentration of total lithium and on the lithium isotopic ratio in the external medium.

British Library Electronic Table of Contents (United Kingdom)

There is strong interest in lithium imaging, particularly because of its significance in battery materials. However, light atoms only scatter electrons weakly and atomic resolution direct imaging of lithium has proven difficult. This paper explores theoretically the conditions under which lithium columns can be expected to be directly visible using annular bright field scanning transmission electron microscopy. A detailed discussion is given of the controllable parameters and the conditions most favourable for lithium imaging.

International Nuclear Information System (INIS)

In order to understand the physical processes concerned with the selective heating by ion cyclotron resonance and with the subsequent collection of heated particles, experiments were carried out with the extraction of lithium samples, enriched with "6Li isotopes. Probe and integral extractors allow to collect enriched Li at the end of the selective heating region. Surface density distribution on the collector and local isotopic content of lithium are measured, as a function of the screen height and the retarding potential. Dependence of the collected amount of lithium and of its isotopic content on the value of the magnetic field is also measured. 4 figs., 2 tabs., 5 refs.

International Nuclear Information System (INIS)

Full text of publication follows: Slightly over-stoichiometric lithium orthosilicate pebbles have been selected as one optional breeder material for the European Helium Cooled Pebble Bed (HCPB) blanket. This material has been developed in collaboration of Research Center Karlsruhe and the Schott Glass, Mainz. The lithium orthosilicate pebbles are fabricated from lithium hydroxide and silica by a melting and spraying method in a semi-industrial scale facility. Lithium hydroxide was selected as the precursor since enriched lithium hydroxide is commercially available. The lithium orthosilicate pebbles produced by the process contains oxide phases besides orthosilicate, but it was also found that the oxide phases can be decomposed by annealing at high temperatures. The lithium orthosilicate pebbles produced in this way possesses satisfactory ...

CERN Document Server

We study the temporal evolution of coronal loops using data from the Solar X-ray Imager (SXI) on board of GOES-12. This instrument allows us to follow in detail the full lifetime of coronal loops. The observed light curves suggest three somewhat distinct evolutionary phases: rise, main, and decay. The durations and characteristic timescales of these phases are much longer than a cooling time and indicate that the loop-averaged heating rate increases slowly, reaches a maintenance level, and then decreases slowly. This suggests that a single heating mechanism operates for the entire lifetime of the loop. For monolithic loops, the loop-averaged heating rate is the intrinsic energy release rate of the heating mechanism. For loops that are bundles of impulsively heated strands, it is an indication of the frequency of occurrence of individual ...

UK PubMed Central (United Kingdom)

A closed loop control process assures that a system performs within control limits. In closed loop control, the system's output feeds back directly to change the system's inputs. We describe an approach...Full Text Available

International Nuclear Information System (INIS)

The new Gaussian potentials and interactions with forbidden states consistent with the phase scattering at low energies were obtained. Cross sections, resonance level spectra and some characteristics of bound states of lithium nuclei are calculated with these potentials.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The detection efficiency of a lithium glass detector was calculated using MCNP code, and the calculation was compared with the published results in Pulsed Sphere Plan. A lithium glass detector of our own was made, and its neutron efficiency was calculated. The calculated neutron efficiency was verified with both pulsed and steady DD neutrons. Characteristics of Neutron response of "6Li detector was discussed. (authors)

International Nuclear Information System (INIS)

Lithium tetrachloroaluminate solutions in thionylchloride, methylacetate and their mixtures are studied by "7Li and "2"7Al NMR. It is found that introduction of methylacetate in the LiAlCl_4-SOCl_2 system results in a change of lithium tetrachloroaluminate formation constant. In the ternary system, Li"+ is solvated by methyl-acetate after complete destruction of tetrachloroaluminate anion. Refs. 9, figs. 2.

International Nuclear Information System (INIS)

A unified calculation of neutron-rich isotopes in lithium is performed using the hyperspherical basis in which the underlying symmetry of each isotope exhibits a simple structure. The variation of the binding energy as a function of mass number is qualitatively reproduced, and the asymptotic of radial distribution of each isotope decreases exponentially. The form factors of the lithium isotopes are calculated and display diffraction minima. 27 refs., 3 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

In order to get the separation of natural isotopes of lithium by electrolytic amalgamation, an electrolytic cell with a confined mercury cathode was used to obtain data for the design of a separation stage. The initial work was followed by the design of a moving mercury cathode electrolytic cell and three experiments with six batches stages were performed for the determination of the elementary separation factor. The value obtained, 1.053, was ill agreement: with the specialized literature. It was verified in all experiments that the lithium - 6 isotope concentrated in the amalgam phase and that the lithium - 7 isotope concentrated in the aqueous phase. A stainless-steel cathode for the decomposition of the lithium amalgam and the selective desamalgamation were also studied. In view of the results obtained, a five stages continuous scheme was proposed. (author)

International Nuclear Information System (INIS)

Ultrathin solid polymer electrolyte membranes containing sulfonic ester groups were prepared by polymerization of methyl benzenesulfonate and octamethylcyclotetrasiloxane in a glow discharge plasma. The sulfonic ester groups of the plasma polymer were transformed to lithium sulfonate groups by treatment with lithium iodide. Hybridization of this plasma polymer containing the lithium sulfonate groups with poly(ethylene oxide) (average Mw 300) resulted in the formation of a single lithium ion conductive film. The hybrid polymer electrolyte films were about 1 #mu#m thick, pinhole-free, adherent to various substrates, and showed ionic conductivities at 60 degrees C of the order of 10"- "6 S cm"- "1 (10"2 #OMEGA# cm"2 resistance per unit area of as-prepared solid polymer electrolyte). This material shows promise for electrochemical applications such as all solid-state lithium batteries, ...

British Library Electronic Table of Contents (United Kingdom)

Previously, we demonstrated that the lithium ion conduction in the perovskite-type manganese fluoride is attributed to counter cation-site vacancy mechanism. The divalent counter cation-doped KxBa(1-x)/2MnF3 was theoretically predicted as the lithium ion conductor in the perovskite-type manganese fluoride. In this study, we considered the oxygen doping for KxBa(1-x)/2MnF3 to realize the higher lithium ion conductivity. It is because lithium ion forms the stronger ionic bond with the doped oxygen anion. The hybrid-DFT calculations were performed to investigate the lithium ion conduction in the oxygen-doped KxBa(1-x)/2MnF3. The calculation results were discussed from the viewpoints of the potential energy curve, electron densities, and charge and spin densities. The effect of the lithium ion...

International Nuclear Information System (INIS)

A new series of lithium ionic liquids were prepared by introducing of two electron-withdrawing trifluoroacetyl groups in borate salts containing two methoxy-oligo(ethylene oxide) groups in the structures. Successive substitution reactions of oligo-ethylene glycol monomethyl ether and trifluroacetic acid from LiBH_4 yielded the lithium salts, which were clear and colorless liquids at room temperature. The fundamental physicochemical properties, such as density, thermal property, viscosity, ionic conductivity, self-diffusion coefficients, and electrochemical stability, were measured. The lithium ionic liquids had self-dissociation ability and conducted ions even in the absence of organic solvents. New polymer electrolytes, named 'ion gels', were prepared by radical cross-linking reactions of a poly(ethylene oxide-co-propylene oxide)tri-acrylate macromonomer in the presence the lithium ionic liquid. An ...

CERN Document Server

A Smarandache quasigroup(loop) is shown to be universal if all its f,g-principal isotopes are Smarandache f,g-principal isotopes. Also, weak Smarandache loops of Bol-Moufang type such as Smarandache: left(right) Bol, Moufang and extra loops are shown to be universal if all their f,g-principal isotopes are Smarandache f,g-principal isotopes. Conversely, it is shown that if these weak Smarandache loops of Bol-Moufang type are universal, then some autotopisms are true in the weak Smarandache sub-loops of the weak Smarandache loops of Bol-Moufang type relative to some Smarandache elements. Futhermore, a Smarandache left(right) inverse property loop in which all its f,g-principal isotopes are Smarandache f,g-principal isotopes is shown to be universal if and only if it is a Smarandache left(right) Bol loop in which all its ...

Energy Technology Data Exchange (ETDEWEB)

Characteristics of pressure drop and heat transfer have been investigated for a lithium single-phase flow and a helium-lithium two-phase flow in a horizontal conducting circular channel in the presence of a uniform transverse magnetic field up to 1.4 T as related to the lithium cooling for magnetic-confinement fusion reactors. By the application of the magnetic field to the lithium single-phase flow, remarkable heat transfer enhancement has been observed at the top wall due to the suppression of the mixed convection occurring in the low Peclet number range, while appreciable heat transfer deterioration appeared in the high Peclet number range. It has been confirmed that the helium-lithium two-phase flow can reduce the high magnetohydrodynamic (MHD) pressure drop in a lithium single-phase flow, and it can provide much better heat transfer performance than that in ...

Energy Technology Data Exchange (ETDEWEB)

For the development of high ionic conductive solid electrolyte, LiTi2(PO4)3 (LTP), one of the promising inorganic solid electrolyte, was synthesized to investigate an effect of additional lithium salt on the ion conductivity. Lithium salt added LTP composite electrolyte sintered at 900{degree}C exhibited highest conductivity, which was two order magnitude higher than pure LTP. Effects of lithium salt addition are as follows. Conductivity of the composite electrolyte provided larger sintering temperature dependence than the pure LTP. From X-ray diffraction analysis, structures and compositions were resemble between two composite electrolytes. Byproducts except LTP provided rather low conductivity. It was suggested that melted constitution in the composite can affect the sintering improvement by the additional lithium salt at temperatures over 800 {degree}C. From the observation of ruptured surface of ...

International Nuclear Information System (INIS)

The absorption spectra of plutonium ions in nitric acid have been described. There is a characteristic change in the absorption spectra of Pu v in lithium nitrate solutions. In 2 M-lithium nitrate a new peak at 969 nm and high absorption at 1200 nm are noticed. A decrease in the absorption by about 20% and the appearance of a new shoulder at 1120 nm in 6 M-lithium nitrate are found. There is no change in the spectrum in 4 M-lithium nitrate. The absorption spectra of plutonium ions in the spectral range 200 - 400 nm are interesting. All plutonium ions have an intense band in the region 250 - 260 nm as well as a less intense and rather diffuse band at 320 - 330 nm in lithium nitrate solutions the sharp band at 250 - 260 nm has disappeared. This suggests that this band is very sensitive to the environmental field. The band is probably produced by 5 F"q#-># 5 f"q"-"1 6 d transition ...

International Nuclear Information System (INIS)

Lithium orthosilicate (Li_4SiO_4) powder was synthesized by the solid-state reaction of lithium oxide with amorphous silica, and the effects of fabrication parameters on the structural characteristics of the product were investigated. Processing considerations such as milling media, drying technique, calcination time and temperature, pressing behavior, sintering time and temperatures, and impurity concentration were addressed. The initial powder particle size was observed to be important in achieving high sintered density, with densities as high as 98% TD achieved with a particle size of approximately 1 #mu#m. 9 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

The lithium-polymer energy storage technology requires the production of thin films of huge surface. The BT-EdF-CEA consortium has studied the various manufacturing techniques of these films and their assembly. The process was chosen according to its productivity, low expensiveness, ecological impact and energy performances with capacities reaching 40 Ah. This paper explains: the objectives and specifications of the project, the advantage of the consortium and the role of the different partners, the results (coating, dry extrusion and battery element manufacturing techniques), and the electrochemical performances of the elements. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

Differences in the biological disposition and in the effects of the stable lithium isotopes, Li-6 and Li-7, in animals were characterized. A somewhat higher toxicity was associated with WLiCl compared to XLiCl with NLiCl intermediate. All lithium treatments increased water intake and resulted in weight gain. Peak plasma concentration was slightly high for 6Li than 7LiCl suppressed action potential amplitudes during tetanic stimulation more than NaCl when added to Renger solution bathing ganglia.

Energy Technology Data Exchange (ETDEWEB)

Electrochemical techniques have been used to study the reversible insertion of sodium into hard-carbon host structures at room temperature. In this paper the authors compare these results with those for lithium insertion in the same materials and demonstrate the presence of similar alkali metal insertion mechanisms in both cases. Despite the gravimetric capacities being lower for sodium than lithium insertion, the authors achieved a reversible sodium capacity of 300 mAh/g, close to that for lithium insertion in graphitic carbon anode materials. Such materials may therefore be useful as anodes in rechargeable sodium-ion batteries.

British Library Electronic Table of Contents (United Kingdom)

In this paper we describe a Ni-Sn intermetallic material obtained via template electroplating synthesis. The structure and the morphology of this material are investigated by X ray diffraction (XRD) and Scanning Electron Microscopy (SEM) analyses. We demonstrate that Ni-Sn behaves as a sub-micrometric electrode showing a favourable response when cycled in a lithium cell. The results here reported suggest that the template electroplating is a promising synthetic approach that can lead to an optimized structure and morphology of the Ni-Sn electrode, such as to confer it a role of a high capacity anode in advanced lithium ion batteries.

Energy Technology Data Exchange (ETDEWEB)

Lithium (Li) plating-stripping reaction properties at the lithium phosphorus oxynitride glass electrolyte (LiPON)/copper thin film (Cu) interface is improved by the insertion of nano-thickness platinum (Pt) layer at the interface. The LiPON films are formed on mirror-polished lithium-ion conductive solid electrolyte sheets, and current collector thin films of Li, Cu-Pt multi layer, and Cu are formed on the LiPON films. The plating-stripping reactions at the LiPON/current collector films interface are carried out by galvanostatic and potential sweep measurements. Galvanostatic measurements reveal that Pt layer insertion reduces the overvoltage of the reaction and improves its coulomb efficiency. Also, cyclic voltammetry measurement suggests formation of Li-Pt alloys at higher voltages than 0 V (vs. Li/Li{sup +}) during the lithium plating process. Scanning electron microscopy observation clarifies that ...

International Nuclear Information System (INIS)

Neutron yield from the "6","7Li + d reaction has been investigated. The results obtained are compared with the published data with some theoretical models.

British Library Electronic Table of Contents (United Kingdom)

Porous SnO2 nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807mAhg^-^1 after 50cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO2 nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated t...

Energy Technology Data Exchange (ETDEWEB)

We present a laser spectroscopic approach for measuring the charge radius of the halo nucleus {sup 11}Li and report on recent progress in the development of the experimental apparatus.

Energy Technology Data Exchange (ETDEWEB)

We analyze the nucleon axial-vector coupling to two loops in chiral perturbation theory. We show that chiral extrapolations based on this representation require lattice data with pion masses below 300 MeV.

UK PubMed Central (United Kingdom)

The T-loop motif is an important recurrent RNA structural building block consisting of a U-turn sub-motif and a UA trans Watson–Crick/Hoogsteen base pair. In the presence of...Full Text Available

UK PubMed Central (United Kingdom)

A hitherto unreported immunofluorescent staining pattern obtained from human sera is described. Serum from six patients was found to possess specific antibody activity against lining cells of loops...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

It has been observed that dislocation loops form and grow during annealing of silicon wafers implanted at doses above the amorphization threshold. Dislocation loops can act to store interstitials for prolonged periods of anneals, sustaining an interstitial super-saturation and thus causing substantial transient enhanced diffusion (TED). The authors have developed a comprehensive model which, in combination with a model and parameters for {l_brace}311{r_brace} defects from previous work, accounts for the formation and evolution of dislocation loops during ion implant annealing, as well as giving the correct TED behavior.

Energy Technology Data Exchange (ETDEWEB)

Presented are some preliminary studies made in preparation for the design of a solar powered loop for desalination by humidification - dehumidification process. The studies concentrated on the evaluation of different parameters affecting the performance of the combination of different components in such a loop in the hope of outlining the most decisive factors for the choice or design of solar collectors or heat source. The results presented relate to the performance of two of the most important components in a loop of such purpose, that is: the humidifying and the dehumidifying columns or stacks. 4 refs.

Energy Technology Data Exchange (ETDEWEB)

The electrical resistivity at low temperatures (T = 10 to 90 K) of the lithium isotopes /sup 6/Li and /sup 7/Li and of an isotopic mixture /sup 7 +6/Li has been studied. The specimens contained a small amount of chemical impurities. An appreciable difference was observed in the temperature dependence of the resistivity produced both by deformation of the phonon spectrum, related to the change in isotopic composition, and by the presence of chemical impurities making the nonequilibrium part of the electron distribution function more isotropic.

Energy Technology Data Exchange (ETDEWEB)

Values of frequency splittings in the lithium isotopes have been determined with the aid of laser-induced fluorescene in a supersonic beam, perpendicularly irradiated by a CW ring dye laser. The residual 2s-2p isotope shift has been found to bw 4721.8 +- 2.0 MHz, leading to a specific mass shift for the 2p level of -3610.8 +- 5 MHz.

Energy Technology Data Exchange (ETDEWEB)

Calculations of total and angle-differential excitation cross sections for the electron impact excitation of lithium-like iron were performed with the R-matrix formulation. The alignments of the excited states 1s{sup 2}np {sup 2}P{sub 3/2} are also presented for n=3 and 4 along with the angular photon distribution from these states to the ground state. Relativistic effects were included in the present calculations by the Breit-Pauli Hamiltonian.

Energy Technology Data Exchange (ETDEWEB)

A solid electrolyte for lithium batteries requires several properties: a good ionic conductivity of about 10{sup -3} S/cm at 298 deg. K, a high cationic transport number (greater than 0.5), a redox stability window higher than 4.5 V, a good stability of the interface with the lithium electrode, and a sufficient mechanical stability. The family of gelled or hybrid electrolytes seems to meet all these requirements. Thus, a systematic study of the gelling of an ethylene carbonate and lithium bistrifluorosulfonimide (LiTFSI) based electrolyte has been carried out. The polymers used for gel or pseudo-gel synthesis are POE, PMMA and PAN which represent 3 different cases of interaction with the electrolyte. All the properties mentioned above have been studied according to the nature of the polymer and to the concentration of lithium salt, showing the advantages and drawbacks of each polymer. The possibility of ...

Science.gov (United States)

The lithium storage properties of graphene nanosheet (GNS) materials as high capacity anode materials for rechargeable lithium secondary batteries (LIB) were investigated. Graphite is a practical anode material used for LIB, because of its capability for reversible lithium ion intercalation in the layered crystals, and the structural similarities of GNS to graphite may provide another type of intercalation anode compound. While the accommodation of lithium in these layered compounds is influenced by the layer spacing between the graphene nanosheets, control of the intergraphene sheet distance through interacting molecules such as carbon nanotubes (CNT) or fullerenes (C60) might be crucial for enhancement of the storage capacity. The specific capacity of GNS was found to be 540 mAh/g, which is much larger than that of graphite, and this was increased up to 730 mAh/g and 784 mAh/g, respectively, by the ...

Energy Technology Data Exchange (ETDEWEB)

Porous SnO{sub 2} nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807 mAh g{sup -1} after 50 cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO{sub 2} nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated that this simple method could be extended for the synthesis of porous metal oxide nanotubes with high performances in ...

International Nuclear Information System (INIS)

Nano indentation analysis and transmission electron microscopy observation were performed to investigate a microstructural evolution and its influence on the hardening behavior in Fe-Cr alloys after an irradiation with 8 MeV Fe4+ ions at room temperature. Nano indentation analysis shows that an irradiation induced hardening is generated more considerably in the Fe-15Cr alloy than in the Fe-5Cr alloy by the ion irradiation. TEM observation reveals a significant population of the a0 dislocation loops in the Fe-15Cr alloy and an agglomeration of the 1/2a0 dislocation loops in the Fe-5Cr alloy. The results indicate that the a0 dislocation loops will act as stronger obstacles to a dislocation motion than 1/2a0 dislocation loops.

International Nuclear Information System (INIS)

1 - Description of test facility: The LOBI facility is a 1/700 scale model of a four loop PWR and has two primary loops, the intact loop representing three loops and the broken loop representing one loop of a four-loop PWR. The reactor pressure vessel model contains an electrically heated rod-bundle with 64 rods and a heated length of 3.9 m. The nominal heating power is 5.3 MW. The downcomer is of annular shape. An upper head simulator is connected to the vessel. Each of the two primary loops contains a pump and a steam generator. The different mass flows in the loops are established by the pump speeds, since the two pumps are identical. Heat is removed from the steam generators by a secondary system. ECC water can be supplied from two accumulators, one for each loop. Cold or hot ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility of spectroscopic measurement of the velocity distribution of alpha particle using the ablation cloud of a lithium or boron pellet was tested in the DT experiment of TFTR. The measurement was performed using a 10-channel narrow-band filtered spectrometer in the wavelength covering the 3.5 MeV alpha particle Doppler broadening region of the He II 468.6 nm line and its vicinity. The spectra from a lithium pellet consists of the continuum bremsstrahlung background, lithium line emissions and possibly a 468.6 nm helium line. However, no clear evidence of alpha particles was observed, even when boron pellets were injected. (orig.) 4 refs.

International Nuclear Information System (INIS)

A study was made on extraction of a series of lithium and calcium salts by monopodands L with common formula R-C_6H_4-O-(CH_2CH_2O)_n-C_6H_4-R, where R - CH_2P(O)Ph_2, n 1-3. Extraction-chromatographic separation of lithium and calcium isotopes in systems of metal aquacomplex-solvatocomplex with L in organic phase was conducted. It was established that separation coefficients of "6Li/"7Li isotopes ranged between 1.003 #+-#0.001 and 1.017 #+-#0.002 at the maximal separation degree equal to 1.60. Separation of "4"0Ca/"4"4Ca isotopes was not fixed. 12 refs., 4 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

We have determined the nuclear charge radius of 11Li by high-precision laser spectroscopy. The experiment was performed at the TRIUMF-ISAC facility where the 7Li-11Li isotope shift was measured in the 2s to 3s electronic transition using Doppler-free two-photon spectroscopy with a relative accuracy better than 10 5. The accuracy reached in previous experiments on the other lithium isotopes was improved. Most of the isotope shifts measured in the experiment are due to difference in the mass of the nuclei but small contributions are produced by the change in proton distribution, QED and relativistic effects have to be taken into account as well. By comparing the experimental results with sophisticated atomic calculations of the mass dependent effect the nuclear charge radii of the lithium isotopes are found to decrease monotonically from 6Li to 9Li while the nuclear charge radius of 11Li is about 11% larger than that of 9Li.

Energy Technology Data Exchange (ETDEWEB)

Single stage separation factors ..cap alpha.. have been determined for /sup 6/Li and /sup 7/Li between lithium ions in methanol and complexed ions with a cryptand (2 sub(B), 2, 1) polymer. The /sup 6/Li was concentrated in the cryptand. The separation factors were compared with the values of other chemical exchange systems. The maximum enrichment factor obtained was epsilon = 0.047 +- 0.002. The figure is one of the greatest in the chemical exchange reactions without valence change and almost 10 times larger than the values of ion exchangers. The variation in ..cap alpha.. depending on the chemical species was small in the non-aqueous system. High enrichment of lithium isotopes was expected to be achievable by means of the chromatographic application of the cryptand (2 sub(B), 2, 1).

Energy Technology Data Exchange (ETDEWEB)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10{sup -6} S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

Energy Technology Data Exchange (ETDEWEB)

The incorporation of additives designed to sacrificially react on the surface of cathode materials of lithium ion batteries has been investigated. Addition of low concentrations of inorganic additives including lithium bisoxalatoborate (LiBOB), lithium difluorooxalatoborate (LiBF{sub 2}(C{sub 2}O{sub 4})), and tetramethoxy titanium (TMTi) to 1 M LiPF{sub 6} in 1:1:1 EC/DEC/DMC improves the capacity retention of Li/Li{sub 1.17}Mn{sub 0.58}Ni{sub 0.25}O{sub 2} cells cycled to 4.9 V vs. Li. Surface analysis of the cathode materials (XPS and IR) suggests that structure of the cathode surface film is modified by the presence of the additives resulting in a decrease in detrimental electrolyte oxidation reactions on the cathode surface. (author)

Energy Technology Data Exchange (ETDEWEB)

It is well known that a protective film is formed on the graphite negative electrode in ethylene carbonate (EC) electrolyte solution. This film is lithium-ion conductive and protects the decomposition of the electrolyte solution. In the present paper, the electrode/electrolyte interfaces in lithium-ion rechargeable batteries were characterized by three-dimensional complex impedance plots, whose axes are real, imaginary parts and time. The film resistance R {sub sei} and charge transfer resistance R {sub ct} were determined for negative electrodes in EC/ethyl methyl carbonate (EMC) electrolyte solution, and the formation mechanisms of the interfacial film were discussed. Furthermore, the contributions of vinylene carbonate and ethylene sulfite, which are added into the electrolyte solution for the film formation, were investigated.

Energy Technology Data Exchange (ETDEWEB)

Cathode materials for rechargeable rocking chair or lithium-ion batteries, are reviewed. The emphasis is placed on the comparison between specific capacities and rechargeability of lithium-containing high voltage cathode materials such as manganese oxides and LiMO{sub 2} compounds, where M is Co or Ni. It is generally found that the maximum reversible capacities for the most promising materials fall in the range 100-120 mAh/g, and decaying to around 75 mAh/g after several hundred cycles. The rechargeability is similar for the most commonly considered materials: LiMn{sub 2}O{sub 4}, LiCoO{sub 2} and LiNiO{sub 2}. No improvements in capacity or rechargeability, beyond what have been found for these materials, is observed by substitution of other elements into these compounds

International Nuclear Information System (INIS)

Scaling criteria for a natural-circulation loop are examined. The present state of knowledge of scaling to obtain similarity during single- and two-phase flow conditions in a closed loop are reviewed, and an alternative development of two-phase similarity parameters is presented. The loop scaling criteria are the results of analyses in which flow from one component to another is considered. In this work, boundary conditions for the closed loop are developed to obtain scaling criteria for leak flow, injection flow, and heat loss to ambient. The leak scaling criteria are specialized for modeling approaches using prototypic fluid at prototypic or reduced pressures. The derived scaling parameters are examined for their application to two existing scaled test facilities: the Multi-Loop Integral System Test (MIST) facility at Babcock and Wilcox, and the UMCP 2 x 4 facility at the ...

CERN Document Server

The Drell-Yan mechanism for the production of lepton pairs is one of the most basic processes for physics studies at hadron colliders. It is therefore important to have accurate theoretical predictions. In this work we compute the two-loop virtual mixed QCD x QED corrections to Drell-Yan production. We evaluate the Feynman diagrams by decomposing the amplitudes into a set of known master integrals and their coefficients, which allows us to derive an analytical result. We also perform a detailed study of the ultraviolet and infrared structure of the two-loop amplitude and the corresponding poles in epsilon.

Energy Technology Data Exchange (ETDEWEB)

This study is targeted to the NLO corrections of multileg processes, very important for the LHC. Starting from the construction of Feynman diagrams, the analytical reduction of general one-loop integrals to scalar master ones, the calculation of color structures, manipulation of spinor lines and other amplitude constituents and finally phase space point selection are obtained by use of a program producing Fortran code for numerical calculation of one-loop corrections for processes like gg{yields}t anti tgg. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Lithium ion batteries use an oxide as a positive electrode and a carbon material as a negative electrode. The performances of carbon electrodes have rapidly evolved during the last years thanks to the substitution of soft carbons of Conoco or MCMB-2510 type by graphites (F-399, MCMB-2528) and then by hard carbons. These high capacity carbons (700 mAh/g) have higher service life and volume capacity than graphites but their irreversible losses are greater (>20%). In this work, materials with similar electrochemical performances are prepared by mechanical crushing. Mechanical crushing allows to obtain a wide range of carbon materials with various morphologies, specific surfaces and levels of disorder. The formation of the passivation film is directly linked with the surface of materials. A reaction scheme of the reversible and irreversible capacities has been defined and has permitted to obtain compounds with reversible capacities of 720 mAh/g (2 ...

Energy Technology Data Exchange (ETDEWEB)

Solid-state lithium batteries with a unique construction are reported in this paper. These batteries contain two kinds of lithium ion-conductive solid electrolytes, LiI-Li{sub 2}S-P{sub 2}S{sub 5} glass contacted with the anode material and Li{sub 3}PO{sub 4}-Li{sub 2}S-SiS{sub 2} glass or Li{sub 2}S-GeS{sub 2}-P{sub 2}S{sub 5} crystalline material contacted with the cathode. The former electrolyte was selected as that stable to electrochemical reduction, and the latter two to oxidation. This construction made it possible to use graphite as the anode and LiCoO{sub 2} as the cathode in the solid-state lithium battery. The energy density of the battery is 390 W h{center_dot}l{sup -1} and 160 W h{center_dot}kg{sup -1} per total volume and weight of the cathode and anode layers, respectively, which are comparable to those of commercialized Li-ion batteries.

International Nuclear Information System (INIS)

Lithium isotopes are used as the raw material of tritium which is the fuel for fusion power generation and the material for fusion reactors, accordingly those are indispensable for future nuclear fusion power generation. As for boron isotopes, the neutron absorption corss section is very large, therefore, they are used for shielding neutrons and controlling fast neutron reactors. In order to further develop the utilization of nuclear power, it is important to develop the technology for separating and refining light element isotopes in large amount. In fiscal year 1995, the relation of the ion sieve characteristics of inorganic ion exchanger and the behavior of lithium isotope separation was examined. The behavior of forming boron complex of polyol amine was examined by B-11 NMR. These experiments and the results are reported. It was shown to be feasible that lithium is adsorbed from seawater, and isotopes are concentrated. ...

Energy Technology Data Exchange (ETDEWEB)

Shell model calculations are reported for the properties of normal parity states of /sup 7/Li, /sup 8/Li and /sup 9/Li. Fits to new experimental data are displayed, some ambiguities resolved, and structure information provided for help in further investigations.

Energy Technology Data Exchange (ETDEWEB)

ABO{sub 3} perovskite-type oxides having vacancies in the A-sites of their structure are interesting candidates for solid electrolytes when their A-sites are occupied by Li{sup +} ions having a high mobility. This is the case with the [Li{sub 3x}La{sub 2/3-x}]TiO{sub 3} solid solution compound which has a 10{sup -3} S cm{sup -1} ionic conductivity at ambient temperature. Electrochemical intercalation in this material is possible thanks to the presence of Ti{sup 4+} but the small amount of vacancies (0.33 maximum) leads to a low intercalation rate. In order to solve this problem, the LiLaNb{sub 2}O{sub 7} material which has a greater amount of vacancies has been studied and the results relative to the electrochemical intercalation of lithium in this perovskite are presented. The thermodynamical and kinetics properties of the lithium intercalation reaction have been studied by intermittent galvano-static discharges and impedance spectroscopy in ...

British Library Electronic Table of Contents (United Kingdom)

High lithium-ion (Li^+) conductive garnet-structured lanthanum lithium zirconate (LLZ) solid electrolyte is prepared by incorporation of appropriate amounts of silicon (Si) and aluminum (Al). The resultant pelletized LLZ obtains total Li^+ conductivity of 6.8x10^-^4Scm^-^1 at 298K. This improved conductivity is nearly identical with the bulk Li^+ conductivity of the LLZ reported earlier, suggesting that the grain boundary resistance is effectively reduced by the incorporation of Si and Al. Microanalyses by transmission electron microscopy coupled with energy-dispersive X-ray microanalysis and electron energy-loss spectroscopy revealed the presence of amorphous Li-Al-Si-O with nano crystalline LiAlSiO4 at grain boundaries. Fast lithium-ion transport around the amorphous Li-Al-Si-O/LiAlSiO4 ...

Energy Technology Data Exchange (ETDEWEB)

The confocal Raman micro-spectroscopy has been used for the study of a Lithium/polymer electrolyte-LiTFSI/V{sub 2}O{sub 5} type battery in which the polymer electrolyte thickness is of about 80 {mu}m. The analysis is performed on the side of the battery thanks to a specially designed cell which preserves all the characteristics of the real system. The analysis is performed on 20 points aligned between the anode and the cathode and with a depth of several tenth of {mu}m. The analysis of data obtained during charging/output cycles allows to evaluate the gradients of salt concentration inside the electrolyte, the pollutions of LiOH, Li{sub 2}CO{sub 3}, Li{sub 2}O and Li{sub 3}N -type at the lithium interface, but also the structural modifications of the cathode material. The in-situ study of concentration gradients inside the electrolyte is of prime importance for the understanding of dendrites growth. (J.S.) 11 refs.

Energy Technology Data Exchange (ETDEWEB)

This document, Part 2 of Volume 2, provides appendices to this report and includes the following technologies, zinc/air battery; lithium/molybdenum disulfide battery; sodium/sulfur battery; nickel/cadmium battery; nickel/iron battery; iron/oxygen battery and iron/air battery. (FI)

International Nuclear Information System (INIS)

Calculations in "7Li have been carried out for the differential coherent elastic scattering cross-section of thermal neutrons at a fixed scattering angle #theta#_0(148"o) and varying the energy of incident neutrons (or corresponding d-spacings). The results are reported, as variations of the ratio #SIGMA#_0"c"o"h (#theta#_0, d)/#SIGMA#_0"c"o"h (#theta#_0) with d-spacing, at atmospheric pressure and at two temperatures, 80 and 20 K. The calculations at 80 K correspond to BCC lithium whereas at 20 K all the possible crystallographic structures of polytype lithium (BCC, 9R, HCP and FCC) were considered. On comparing our results with the time-of-flight (TOF) measurements of Berliner et al. (Physical Review, B40, 12086, 1989) we find that up to 80 K lithium-7 does not undergo any martenistic transformation whereas the structural state at 20 K can be described by the co-existence of the original BCC phase with 9R, HCP and FCC ...

Energy Technology Data Exchange (ETDEWEB)

An ever first attempt has been made to investigate the possible anode performance characteristics of LiFePO{sub 4}, popularly known so far as an environmentally compatible and economically viable lithium battery cathode material. The compound LiFePO{sub 4} has been synthesized via solid state method and explored for the first time as an anode material against lithium metal through the present study. Surprisingly, an initial capacity of circa 620 mAh/g has been exhibited by LiFePO{sub 4} anode, which is about 4-5 times higher than the capacity of the corresponding LiFePO{sub 4} cathodes. Also an excellent coulombic efficiency value of 99% has been shown by the compound, especially upon extended cycling. The extraordinarily higher specific capacity values of LiFePO{sub 4} anodes may be exploited suitably for practical lithium battery applications.

Energy Technology Data Exchange (ETDEWEB)

A solid electrolyte cell comprises an alkali metal anode, e.g. lithium, a halogen-containing organic polymer cathode and a solid elecrolyte between the anode and the cathode. The cathode comprises iodine-containing vacuum-cyclised polyacrylonitrile, and the solid electrolyte is preferably lithium iodide and halogen-free vacuum-cyclised polyacrylonitrile. This patent also discloses the use of isotactic polyacrylonitrile, a method of making a cathode comprising iodine-containing vacuum-cyclised polyacrylonitrile, and novel methods of making the solid elecrolyte cells described.

Energy Technology Data Exchange (ETDEWEB)

An experiment has been performed to investigate the chemical reaction between the liquid phases of the eutectic lithium-lead (Li/sub 17/Pb/sub 83/) and water. The reactants and products were constrained within a closed reaction vessel, allowing the extent of reaction to be determined from the partial pressure of the hydrogen reaction product. The data from the tests showed that the extent of reaction did not depend upon the water temperature. The data also indicated that the extent of reaction passed through a maximum as the initial liquid metal temperature was varied from 350 to 500 C, and a model was developed to explain this behavior. 11 refs., 3 figs.

Energy Technology Data Exchange (ETDEWEB)

Lithium storage metals and alloys can be suitable high-capacity anode materials for lithium-ion batteries, when the morphology is specifically designed. Here, we compare three different Sn/SnSb multiphase anode materials in powder form, which have been prepared in aqueous and organic solution by chemical precipitation using NaBH{sub 4} or Zn as reductive agents. The obtained morphologies, chemical compositions, and the electrochemical performance will be comparatively discussed. The variety of synthesis parameters which have an effect on the morphology of the obtained anode materials will be particularly highlighted.

Energy Technology Data Exchange (ETDEWEB)

SnO{sub 2}-carbon nanotube (CNT) composite sheets are synthesized using poly(vinylpyrrolidone) to uniformly load a monolayer of SnO{sub 2} nanoparticles onto the surfaces of CNTs and CNT bundles within cross-stacked CNT sheets. When they are used as high-capacity (over 850 mA h g{sup -1}) and binder-free anodes in rechargeable lithium-ion batteries, they exhibit good cycle performance. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

International Nuclear Information System (INIS)

Compared with that of Daya Bay Nuclear Power Plant, the reactor power of QS-II Nuclear Power Plant is decreased and the primary coolant system is changed from three loops to two loops. Thereby the related systems were re-designed, and corresponding tests and engineering validation were carried out. Results of preliminary operation indicate that it is successful. The author describes the design modifications, features and corresponding tests of some systems, reflecting the successful incorporation of engineering and testing, and revealing the capability to develop nuclear power and design the large or medium sized commercial NPP on Self-Reliance in China

Science.gov (United States)

The spread spectrum acquisition and tracking performance for the Shuttle S-band and Ku-band communication links are analyzed and compared to test results. The S-band link requirements are more severe than those of the Ku-band links, hence, different despreader designs were developed for the two systems. The S-band despreader acquires pseudonoise code lock by examining all possible code phases in half chip steps while the Ku-band despreader acquires pseudonoise code lock by continuously sweeping a tau-jitter loop. Both despreaders employ a tau-jitter loop for code tracking. The code tracking performance is computed for the tau-jitter loop and compared to that of the more complex delay lock loop.

International Nuclear Information System (INIS)

Experiments have been performed with the PMK integral-type facility, a model of WWER-440 type PWRs, to investigate two-phase natural circulation behaviour. The phenomena to be expected in this reactor type are different from those in PWRs with vertical steam generators mainly due to the loop seal in the hot leg and the horizontal layout of the steam generator heat transfer tubes. The experiments showed that the system is repressurized when the water level drops to the hot leg elevation due to the effect of the loop seal. Opening of the loop seal can be smooth, but may lead to oscillations depending on the power and the mass inventory. Natural circulation recovers after the hot leg loop seal is opened, but then decreases with further mass inventory decrease. (orig.).

British Library Electronic Table of Contents (United Kingdom)

Background: Thyroid-stimulating autoantibodies (TSAb) bind to the thyrotropin receptor (TSHR) extracellular domain, or ectodomain (ECD), comprising a leucine-rich repeat domain (LRD) linked by a hinge region to the transmembrane domain (TMD). The LRD (residues 22???260; signal peptide 1???21) contains two disulfide-bonded loops at its N-terminus. In the crystal structure of the isolated LRD complexed with human TSAb monoclonal antibody (mAb) M22, N-terminal disulfide loop 1 (residues 22???30) could not be determined because of crystal disorder. Nevertheless, present crystal structure data are interpreted to exclude a role for the LRD N-terminal disulfide loops in the TSAb epitope(s), contradicting prior functional evidence of a role for these loops in TSAb function. Materials and Methods: ...

Science.gov (United States)

... of the loop filter based on ... algorithms, including delta-sigma approaches, routinely uses double-precision floating point number representations for ...

Energy Technology Data Exchange (ETDEWEB)

Lithium metal-polymer electrolyte batteries with improved utilisation of the active material at a moderate-low temperature (65degC) were realised. Low molecular weight poly(ethylene glycol) (PEG, MW=2000) was used as the lithium-ion conductive matrix in the composite cathode. The cathode active material was crystalline V{sub 2}O{sub 5}. A blend of poly(ethylene oxide) (PEO, MW=4x10{sup 6}) and PEG was used as a solid polymer electrolyte (SPE). The transport properties of the SPE were evaluated at various temperatures. A specific conductivity as high as 1.0x10{sup -4} S cm{sup -1} was calculated at 45degC. The temperature dependence of the interfacial resistances between lithium/SPE and cathode material/PEG was evaluated. The lithium/SPE interfacial resistance decreases linearly with the temperature. The charge transfer resistance between cathode material and PEG reaches a minimum at 60degC and it does ...

CERN Document Server

All-order spurion-corrected superpropagators and superfield Feynman rules are employed to systematically compute a two-loop corrected effective potential for the O'Raifeartaigh model, that realizes spontaneous supersymmetry breaking. Though the shifted superpropagators are rather nontrivial, superspace techniques may be suitably extended and confirm their efficacy in computing radiative corrections even when supersymmetry breakdown occurs.

Energy Technology Data Exchange (ETDEWEB)

We present a modification of the closed-loop state space model for AO control which allows delays that are a non-integer multiple of the system frame rate. We derive the new forms of the Predictive Fourier Control Kalman filters for arbitrary delays and show that they are linear combinations of the whole-frame delay terms. This structure of the controller is independent of the delay. System stability margins and residual error variance both transition gracefully between integer-frame delays.

Energy Technology Data Exchange (ETDEWEB)

The precipitation of excess silicon interstitials into dislocation loops is modeled. This situation occurs when an amorphous layer is created at the surface in order to avoid boron channeling and form shallow p junctions. The modeling of the nucleation of these extended defects is included into the process simulator IMPACT-4. Their density and mean radius are calculated for several annealing times and temperatures and they are compared with experimental characterizations. This is the first step towards a full modeling of the complex processes involved in the transient enhanced diffusion of boron.

British Library Electronic Table of Contents (United Kingdom)

A formula is obtained which describes the kinetics of low-temperature radiation hardening caused by creation of dislocation loops of interstitial type during irradiation. The radiation hardening of aluminum and vanadium is estimated using this formula and results of experiments on studying processes of nucleation and growth of interstitial dislocation loops in these materials by transparent electron microscopy. It is shown that the proposed formula is valid for description of the kinetics of low-temperature radiation hardening.

Energy Technology Data Exchange (ETDEWEB)

This talk is a brief review of gaugino condensation in superstring effective field theories and some related issues (such as renormalization of the gauge coupling in the effective supergravity theories and modular anomaly cancellation). As a specific example, we discuss a model containing perturbative (1-loop) corrections to the K{umlt a}hler potential and approximate S-duality symmetry.

CERN Document Server

A consistent combination of quantum geometry effects rules out a large class of models of loop quantum cosmology and their critical densities as they have been used in the recent literature. In particular, the critical density at which an isotropic universe filled with a free, massless scalar field would bounce must be well below the Planck density. In the presence of anisotropy, no model of the Schwarzschild black hole interior analyzed so far is consistent.

Science.gov (United States)

A description of LOOP covers the single point mooring (SPM) system; the offshore pipelines connecting each SPM to the pumping platform; the offshore platform complex, a pumping platform and a control platform; the onshore pipelines; and the Clovelly Dome storage terminal.

International Nuclear Information System (INIS)

Very High Temperature gas cooled nuclear Reactor (VHTR), which was coupled with Sulfur-Iodine (SI) thermo-chemical cycle, has been selected for the Nuclear Hydrogen Development and Demonstration (NHDD) project in Korea Atomic Energy Research Institute. Among the various hydrogen production methods, Sulfur-Iodine (SI) thermo-chemical cycle is a good method as a massive hydrogen production without CO2 emission. In SI cycle, the sulfuric acid decomposition is one issue for the material corrosion on high temperature and pressure condition. For the simulation of the sulfuric acid decomposition, we designed a sulfuric acid loop with a small-scale gas loop which is simulated for the integrity and feasibility tests on a H2SO4 decomposition process. The primary objective of the loop is to validate the corrosion and the mechanical performances of a key component of the NHDD, Process Heat Exchanger (PHE). In this paper, we discussed ...

Science.gov (United States)

This paper proposes an optimization algorithm to reduce the distortion produced in the loop-filter of Continuous-Time Sigma-Delta Modulators. The aim of the algorithm is to find the loop-filter implementation that minimizes distortion at the output of the modulator, by modifying the output swing of every integrator. The algorithm is implemented in Matlab as an evolutive searching. During each step of the searching, the algorithm evaluates the harmonical distortion of a tone when it is applied to the modulator with a certain loop-filter implementation. The output of the algorithm is an optimum linear state-space representation of the loop-filter. This particular state-space representation leads to minimum distortion at the output of the modulator when the loop-filter is implemented with some specific circuitry previously defined. As long as the search is of evolutive type, the ...

Energy Technology Data Exchange (ETDEWEB)

The five thermal-hydraulic concepts chosen for advanced PWR have been studied as follows: (1) Critical Heat Flux: Review of previous works, analysis of parametric trends, analysis of transient CHF characteristics, extension of the CHF date bank, survey and assessment of correlations, design of a intermediate-pressure CHF test loop have been performed. (2) Passive Cooling Concepts for Concrete Containment system: Review of condensation phenomena with noncondensable gases, selection of a promising concept (i.e., use of external condensers), design of test loop according to scaling laws have been accomplished. and computer programs based on the control-volume approach, and the conceptual design of test loop have been accomplished. (4) Fluidic Diode Concepts: Review of previous applications of the concept, analysis major parameters affecting the performance, development of a computational code, and conceptual investigation of ...

Energy Technology Data Exchange (ETDEWEB)

Ionic conductive materials are of much interest as an electrolyte for solid-state lithium batteries. Poly(alkylene oxide) and lithium salt complex exhibits high ionic conductivity in terms of its high solubility for lithium salts. However, the temperature dependency of its ionic conductivity is quite large and non-linear, the ionic conductivity drops down at low temperature, especially below glass transition temperature of the polymer. Because its ionic conductive mechanism is derived from its segmental motion of polymer main chain. A novel ionic conductive material, poly[2,6-dimethoxy-N-(4-vinylphenyl)benzamide] is synthesized and confirm ionic conductivity even below glass transition temperature. Ionic conductivity of the polymer with lithium ditrifluoromethylsulfonate imide complex shows 10{sup -5}Scm{sup -1} from 0 to 60{sup o}C. Its temperature dependency is linear, namely Arrehnius type ...

Energy Technology Data Exchange (ETDEWEB)

This thesis is devoted to studies which prepared the construction of an atom Mach-Zehnder interferometer. In such an interferometer, the propagating waves are spatially separated, and the internal state of the atom is not modified. The beam-splitters are diffraction gratings, consisting of standing optical waves near-resonant with an atomic transition. We use the Bloch functions to define the atom wave inside the standing wave grating and thus explain the diffraction process in different cases. We developed a nearly all-analytical model for the propagation of an atom wave inside a Mach-Zehnder interferometer. The contrast of the signal is studied for many cases: phase or amplitude gratings, effects of extra paths, effects of the main mismatches, monochromatic or lightly polychromatic sources. Finally, we discuss three interferometric measurements we think very interesting. The first, the index of refraction of gas for atomic waves, is studied in detail, with numerical simulations. The ...

International Nuclear Information System (INIS)

Ischemic bowel disease is a rare disorder whose incidence is increasing as the mean age of the population increases. Diagnosis by clinical, laboratory and radiologic means is often difficult, and delay in definitive therapy results in substantial morbidity and mortality. A series of 26 consecutive patients, with proved acute superior mesenteric ischemia, was retrospectively reviewed: the authors reports the diagnostic methods performed preoperatively, the site and the cause of infarction and the time passed between the first radiograph and surgery. Plain abdominal radiographs were performed in 25 of 26 patients, screening abdominal US in 23 cases and CT in 19 cases. All radiological examinations were retrospectively reviewed by the three authors, independently, to recognize the different signs of infarction. On plain abdominal films, the findings warranting a presumptive diagnosis of bowel infarction were air-fluid levels (84% of cases), dilated bowel loops (48%), ...

International Nuclear Information System (INIS)

Ultrafine particles of Sn-Sb alloys with different chemical composition have been prepared by hydrogen plasma-metal reaction. Structure, morphology, size and chemical composition of the Sn-Sb ultrafine particles were investigated by transmission electron microscopy, X-ray diffraction, BET gas adsorption, and induction-coupled plasma spectroscopy. It was found that all the particles have spherical shapes, with average particle size in the range of 100-300 nm. The electrochemistry properties as an alternative anode material for lithium-ion batteries have been characterized by constant current cycling and cyclic voltammetry. Electrochemical measurements showed that the alloys with Sn-46.5 at.% Sb have best reversible capacity and capacity retention. It exhibited a high reversible lithium-ion storage capacity of 701 mAh g"-"1 in the initial cycle, which has remained at 81% (i.e., 566 mAh g"-"1) of its original capacity after 20 cycles.

British Library Electronic Table of Contents (United Kingdom)

Lithium-ion batteries are now considered to be the technology of choice for future hybrid electric and full electric vehicles to address global warming. LiCoO2 has been the most widely used cathode material in commercial lithium-ion batteries. Since LiCoO2 has economic and environmental issues, intensive research has been directed towards the development of alternative low cost, environmentally friendly cathode materials as possible replacement of LiCoO2. Among them, spinel LiNi0.5Mn1.5O4 material is one of the promising and attractive cathode materials for next generation lithium-ion batteries because of its high voltage (4.7V), acceptable stability, and good cycling performance. Research advances in high voltage spinel LiNi0.5Mn1.5O4 are reviewed in this paper. Developments in synthesis,...

Energy Technology Data Exchange (ETDEWEB)

A set of computer codes have been developed to produce spectral line shapes of highly stripped ions for a number of transitions in Hydrogenic, Helium-like and Lithium-like species. The choice of the transitions has been dictated largely by the laser compression experiments. The transitions of Hydrogenic species are: Lyman ..cap alpha..; Lyman ..beta..; Lyman ..gamma..; Lyman delta; Balmer ..cap alpha..; and Balmer ..beta... The transitions of Helium-like species are: 1s/sup 2/(/sup 1/S/sub 0/)-1s2p(/sup 1/P); 1s/sup 2/(/sup 1/S/sub 0/)-1s3p(/sup 1/P); 1s/sup 2/(/sup 1/S/sub 0/)-1s4p(/sup 1/P) and the associated dipole-forbidden components. The transitions of Lithium-like species are the entire n = 2 to n = 3 and n = 4 complexes.

Energy Technology Data Exchange (ETDEWEB)

One of the most promising battery types under development for use in both pure electric and hybrid electric vehicles is the lithium-ion battery. These batteries are well on their way to meeting the challenging technical goals that have been set for vehicle batteries. However, they are still far from achieving the current cost goals. The Center for Transportation Research at Argonne National Laboratory undertook a project for the US Department of Energy to estimate the costs of lithium-ion batteries and to project how these costs might change over time, with the aid of research and development. Cost reductions could be expected as the result of material substitution, economies of scale in production, design improvements, and/or development of new material supplies. The most significant contributions to costs are found to be associated with battery materials. For the pure electric vehicle, the battery cost exceeds the cost goal of the US Advanced ...

Energy Technology Data Exchange (ETDEWEB)

Basic properties and battery performances of the novel high temperature stable lithium salt (Li{sub 2}B{sub 12}F{sub 12}, Dilithium Dodecafluorododecaborate; Li{sub 2}DFB) were studied using a Mn-based cathode and anode composed of a hard carbon and graphite mixture. The effect of co-solvents (mainly linear carbonate in electrolyte formulation of PC/EC/co-solvent (5/30/65 vol% mixture)) on conductivity, viscosity, charge-discharge capacities, rate performance, temperature performance, cycle life and storage life at 60 C was investigated. Conductivity of Li{sub 2}DFB electrolyte increased with reducing its viscosity by changing co-solvent and increasing the volume of the higher dielectric solvent. Li{sub 2}DFB electrolytes showed comparable discharge capacity and columbic efficiency against LiPF{sub 6} electrolyte. Li{sub 2}DFB electrolytes improved the storage life and cycle life of a Mn-based cell at 60 C. (author)

CERN Document Server

Infinite loop space theory, both additive and multiplicative, arose largely from two basic motivations. One was to solve calculational questions in geometric topology. The other was to better understand algebraic K-theory. The Adams conjecture is intrinsic to the first motivation, and Quillen's proof of that led directly to his original, calculationally accessible, definition of algebraic K-theory. In turn, the infinite loop understanding of algebraic K-theory feeds back into the calculational questions in geometric topology. For example, use of infinite loop space theory leads to a method for determining the characteristic classes for topological bundles (at odd primes) in terms of the cohomology of finite groups. We explain just a little about how all that works, focusing on the central role played by E infinity ring spaces.

CERN Document Server

We complete the effective potential calculation of the two-loop, top/bottom Yukawa corrections to the Higgs boson masses in the Minimal Supersymmetric Standard Model, by computing the O(at^2 + at*ab + ab^2) contributions for arbitrary values of the bottom Yukawa coupling. We also compute the corrections to the minimization conditions of the effective potential at the same perturbative order. Our results extend the existing O(at^2) calculation, and are relevant in regions of the parameter space corresponding to tan(beta) >> 1. We extend to the Yukawa corrections a convenient renormalization scheme, previously proposed for the O(ab*as) corrections, that avoids unphysically large threshold effects associated with the bottom mass and absorbs the bulk of the corrections into the one-loop expression. For large values of tan(beta), the new contributions can account for a variation of several GeV in the lightest Higgs boson mass.

Energy Technology Data Exchange (ETDEWEB)

In order to apply chemical-looping combustion to a practical power plant, carbon deposition on the solid particle is one of the key problems to be overcome. Six kinds of solid particles were examined to clarify the kinetic behavior of carbon deposition. The effects of the solid composition, feed gas composition, and reaction temperature on carbon deposition were investigated by thermogravimetrical reactor on the basis of NiO/YSZ particle. From the viewpoints of both reactivity and resistance against carbon deposition, the particle of NiO mixed with YSZ (i.e., yttria-stabilized zirconia) was found to be a good candidate for chemical-looping combustion. It has been observed that carbon deposition could be completely avoided with very low concentration of water vapor. By means of a proposed model, the condition that carbon deposition would be avoided was identified. 12 refs., 8 figs., 2 tabs.

CERN Document Server

A fully consistent linear perturbation theory for cosmology is derived in the presence of quantum corrections as they are suggested by properties of inverse volume operators in loop quantum gravity. The underlying constraints present a consistent deformation of the classical system, which shows that the discreteness in loop quantum gravity can be implemented in effective equations without spoiling space-time covariance. Nevertheless, non-trivial quantum corrections do arise in the constraint algebra. Since correction terms must appear in tightly controlled forms to avoid anomalies, detailed insights for the correct implementation of constraint operators can be gained. The procedures of this article thus provide a clear link between fundamental quantum gravity and phenomenology.

British Library Electronic Table of Contents (United Kingdom)

As portable electronics become more advanced and alternative energy demands become more prevalent, the development of advanced energy storage technologies is becoming ever more critical in today's society. In order to develop higher power and energy density batteries, innovative electrode materials that provide increased storage capacity, greater rate capabilities, and good cyclability must be developed. Nanostructured materials are gaining increased attention because of their potential to mitigate current electrode limitations. Here we report on the use of vertically aligned multi-walled carbon nanotubes (VA-MWNTs) as the active electrode material in lithium-ion batteries. At low specific currents, these VA-MWNTs have shown high reversible specific capacities (up to 782mAhg^-^1 at 57mAg^-...

Energy Technology Data Exchange (ETDEWEB)

As a continuation of our previous study, further experiments were performed on Li[sub 3]PO[sub 4]-Li[sub 2]S-SiS[sub 2] lithium ion conductive glass. In the present study, we employed a twin roller for quenching process instead of liquid nitrogen. We found that the glass forming region expands by twin roller technique and conductivity up to 1.5x10[sup -3] S/cm was achieved. Structural analysis on the glass revealed that Li[sub 3]PO[sub 4] doping changes the glass structure of Li[sub 2]S-SiS[sub 2], thereby enhancing the electrical conductivity

Energy Technology Data Exchange (ETDEWEB)

Three-dimensional porous Sn thin film electrodes were prepared by electroless deposition on copper foam, then its morphology and electrochemical property were studied by means of scanning electron microscope (SEM), X-ray diffraction (XRD), electrochemical cycling test and cyclic voltammetry (CV). The porous framework and micro-holes have shown a great structure advantage in restricting severe volume changes when the Sn thin film was employed as anode for lithium-ion battery. The film electrode of sample C with an initial capacity of 676 mAh g{sup -1} showed good cycle performance displayed by retaining a capacity of 313 mAh g{sup -1} after 100 cycles.

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline MnO thin film has been prepared by a pulsed laser deposition (PLD) method. The reversible lithium storage capacity of the MnO thin film electrodes at 0.125C is over 472 mAh g{sup -1} (3484 mAh cm{sup -3}) and can be retained more than 90% after 25 cycles. At a rate of 6C, 55% value of the capacity at 0.125C rate can be obtained for both charge and discharge. As-prepared MnO thin film electrodes show the lowest values of overpotential for both charge and discharge among transition metal oxides. All these performances make MnO a promising high capacity anode material for Li-ion batteries. (author)

British Library Electronic Table of Contents (United Kingdom)

A range of new nanomaterials to replace the active materials in lithium ion batteries are currently being studied and employed in an attempt to overcome various performance limitations of previous technologies. Nanomaterial production and manufacturing techniques appear to fit into a general trend towards more energy intensive production methods for high-tech goods. This does not necessarily imply an increase in lifecycle energy use; artefacts that consume or transform energy during use could possibly regain this increased initial input via increased efficiency in use. In particular, this paper highlights that larger gains could be possible if the artefact in question allows a given service to be provided via an alternative and more efficient system entirely.The lifecycle energy efficienci...

Energy Technology Data Exchange (ETDEWEB)

Observations are reported of the lithium feature (6708 A) in some bright southern stars, most of which are F, G, or K dwarfs. Three of these stars have been suggested as belonging to the Ursa Major Group. Two of these three have the large Li abundance and strong Ca II H and K emission expected of such young stars. The third potential Ursa Major Group member has little Li, but is also not a true kinematic member. No stars were found with abnormal (Li-6)/(Li-7) ratios, in accord with other recent analyses. Thus it appears that all stars have (Li-6)/(Li-7) near the solar/terrestrial value of 0.08. 31 references.

Energy Technology Data Exchange (ETDEWEB)

Recent developments in rechargeable Li-ion battery technology include the use of lithium-carbon compounds instead of metallic anodes. Non-graphitizable carbons offer high capacity as the anode material but it's large irreversible capacity must be solved. The ultimate goals of the present work are to understand the origin of the high capacity and large irreversible capacity in conjunction with the structural change due to Li intercalation and thus to establish a scientific basis for optimizing their performance in real batteries. 'House of cards' model is considered and emphasis is given to find out the size of the pores present in the carbon fibers prepared from an isotropic petroleum pitch and heat treated at 1200degC. Small angle neutron scattering and wide angle neutron scattering results provide enlargement of pores and d-spacing of grapheme layers after Li intercalation. (author)

British Library Electronic Table of Contents (United Kingdom)

As lithium battery technology sets out to bridge the gap between portable electronics and the electrical automotive industry, cathode materials still stand as the bottleneck regarding performances. In the realm of highly attractive polyanion-type structures as high-voltage cathode materials, the sulfate group (SO4)^2^- possesses an acknowledged superiority over other contenders in terms of open circuit voltage arising from the inductive effect of strong covalent S-O bonds. In parallel, novel lithium insertion mechanisms are providing alternatives to traditional intercalation, enabling reversible multi-electron processes securing high capacities. Combining both of these advantageous features, we report here the successful electrochemical reactivity of copper sulfate pentahydrate (CuSO4.5H2O...

International Nuclear Information System (INIS)

In order to study the two-phase natural circulation and flow termination during a small break loss of coolant accident in LWR, simulation experiments have been performed. Based on the two-phase flow scaling criteria developed under this program, an adiabatic hot leg U-bend simulation loop using nitrogen gas and water and a Freon 113 boiling and condensation loop were built. The nitrogen-water system has been used to isolate key hydrodynamic phenomena from heat transfer problems, whereas the Freon loop has been used to study the effect of phase changes and fluid properties. Various tests were carried out to establish the basic mechanism of the flow termination and reestablishment as well as to obtain essential information on scale effects of parameters such as the loop frictional resistance, thermal center, U-bend curvature and inlet geometry. In addition to the above experimental study, a preliminary ...

UK PubMed Central (United Kingdom)

In mice and humans the circadian rhythm of many biochemical reactions, physiology, and behavior is generated by a transcriptional-translation feedback loop (TTFL) made up of the so-called core clock...Full Text Available

UK PubMed Central (United Kingdom)

Endothelial cells and mural cells (smooth muscle cells, pericytes, or fibroblasts) are known to communicate with one another. Their interactions not only serve to support fully functional blood...Full Text Available

Science.gov (United States)

Three major series of experiments have been conducted with the FELIX facility at ANL. Experiments on the coupling between eddy currents and angular displacements of loops and plates in crossed constant and changing magnetic fields demonstrated that the co...

International Nuclear Information System (INIS)

Tensile properties of reduced-activation 10Cr-30Mn austenitic steels with carbon levels from 0.003 to 0.55% were investigated over the temperature range from room temperature to 873 K after neutron irradiation in the Japan Materials Testing Reactor at 573 K to 8.5x10"2"2 n/m"2. Irradiation-induced increase in yield stress increased significantly with carbon concentration up to about 0.1% and it was constant above 0.1% carbon. A high density of dislocation loops with small (below 10 nm) and large (20-30 nm) sizes formed during irradiation. The high density, small loops caused a large irradiation hardening, while the large loops contributed only slightly to irradiation hardening. It was considered that carbon atoms formed the small loops together with irradiation defects. The deformation channeling was observed in the irradiated high carbon steels, 0.11 and 0.55% carbon, but not in the very low carbon ...

UK PubMed Central (United Kingdom)

PurposeWound infection after an ileostomy reversal is a common problem. To reduce wound-related complications, purse-string skin closure was introduced as an alternative to conventional...Full Text Available

Science.gov (United States)

We describe a closed-loop brain-computer interface that re-ranks an image database by iterating between user generated 'interest' scores and computer vision generated visual similarity measures. The interest scores are based on decoding the electroencephalographic (EEG) correlates of target detection, attentional shifts and self-monitoring processes, which result from the user paying attention to target images interspersed in rapid serial visual presentation (RSVP) sequences. The highest scored images are passed to a semi-supervised computer vision system that reorganizes the image database accordingly, using a graph-based representation that captures visual similarity between images. The system can either query the user for more information, by adaptively resampling the database to create additional RSVP sequences, or it can converge to a 'done' state. The done state includes a final ranking of the image database and also a 'guess' of the user's chosen category of ...

UK PubMed Central (United Kingdom)

Hairpin oligonucleotides were synthesized with stems ending in a double-stranded structure, which can be ligated to double-strand breaks in DNA, and with loops that contain nucleotides modified by the...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The theory and application of the optimal control of linear systems to stabilize or improve the system stability is well known. For an optimal linear regulator design, the arbitrariness involved in the parameters of the cost function always affects the final control law and the closed-loop system poles which decide the system dynamic characteristics. A new approach, 'The inverse problem approach' has been developed to overcome this difficulty. The system so designed will have preassigned closed-loop poles and the resulting closed-loop system performance can be ensured. In this paper the inverse problem approach for optimal regulator design is applied to the power system stabilizer (PSS) design for single-machine infinite-bus systems. The results show that, as far as the linearized model is concerned, systems designed by the inverse problem approach have better closed-loop performance ...

UK PubMed Central (United Kingdom)

Essential in mitosis, the human Kinesin-5 protein is a target for >80 classes of allosteric compounds that bind to a surface-exposed site formed by the L5 loop. Not established is why there...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this paper we have proposed a novel gas turbine cycle with hydrogen-fueled chemical-looping combustion, and the system study on two hydrogen-fueled power plants, the new gas turbine cycle and an advanced gas turbine cycle with H{sub 2}/O{sub 2} combustion, has been investigated with the aid of exergy principle (EUD methodology). The hydrogen fueled chemical-looping combustion in the new gas turbine cycle consists of two successive reactions: hydrogen fuel is reacted with metal oxide (reduction of metal oxide), and then instead of air or pure oxygen, the reduced metal is successively oxidized by the saturated air. As a result, the new hydrogen-fueled gas turbine cycle has a breakthrough performance, with at least about 12 percentage-point higher efficiency compared to the gas turbine cycle with H{sub 2}/O{sub 2} combustion, and will be environmentally superior due to complete elimination of NO{sub x} formation. The promising results obtained ...

CERN Document Server

We calculate quark-antiquark potentials using the relationship between the expectation value of the Wilson loop and the action of a probe string in the string dual. We review and categorize the possible forms of the dependence of the energy on the separation between the quarks. In particular, we examine the possibility of there being a minimum separation for probe strings which do not penetrate close to the origin of the bulk space, and derive a condition which determines whether this is the case. We then apply these considerations to the flavoured resolved deformed conifold background of Gaillard et al. We suggest that the unusual behaviour we observe in this solution is likely to be related to the IR singularity which is not present in the unflavoured case.

International Nuclear Information System (INIS)

The bosonic string on R"2"5xS"1 has a series of states turning tachyonic at radii implying T=IT_H. We employ the B picture to examine these thermal states in the one-loop free energy and find them in various combinations, factorizing towards rational points on the real line boundary of the fundamental domain B: (-1/2=# 0). These thermal tachyons are interpreted as signaling Hagedorn instabilities against the production of an l-highly-excited-identical-strings state, which gives a relation between the one-loop partition function and l-point functions. (orig.).

International Nuclear Information System (INIS)

Transient, greatly enhanced diffusion has been observed on annealing solid-phase-epitaxial (SPE) grown Si-Sb alloys. This is shown to be due to a high concentration of interstitials being trapped during SPE regrowth. The migration enthalpy, for diffusion of Sb by an interstitialcy mechanism was measured as 1.8 +/- 0.2 eV. The interstitials eventually condensed into loops, marking the end of the transient. In a SPE grown Si-Bi alloy a similar transient enhanced diffusion was observed, with an activation energy of 2.0 +/- 0.2 eV, but no loops formed. 8 figures, 7 references.

CERN Document Server

In the inflationary scenario of loop quantum cosmology (LQC) in the presence of inverse-volume corrections, we give analytic formulas for the power spectra of scalar and tensor perturbations convenient to confront with observations. Since inverse-volume corrections can provide strong contributions to the running spectral indices, inclusion of terms higher than the second-order runnings in the power spectra is crucially important. Using the recent data of cosmic microwave background (CMB) and other cosmological experiments, we place bounds on the quantum corrections for a quadratic inflaton potential.

International Nuclear Information System (INIS)

Eight years ago, corrosion and tube denting seriously threatened the reliability and design life of steam generators, especially for closed loop arrangements in pressurized water reactors (PWRs). Concentrated research by the Steam Generator Owners Group (SGOG) diagnosed the causes and produced effective solutions, notably guidelines for water chemistry control in the secondary loop. The guidelines recommend specific levels of water impurities and remedial actions to prevent cooling-water leaks in the condenser, prevent air leaks, limit corrosion product buildup, and remove some impurities while neutralizing others. Continued research in SGOB-II is investigating intergranular corrosion and stress corrosion cracking. 3 figures.

Energy Technology Data Exchange (ETDEWEB)

This paper reviews and elaborates on the issue of the dilaton transformation under the usual {tau} {yields} {alpha}{prime}/{tau} target space duality and its non-static generalization (or {sigma}-model duality). It is found that the transformation law {tau} {yields} {alpha}{prime}/{tau}, {phi} {yields} {phi} In ({tau}/{alpha}{prime}) which guarantees duality at the one-loop {sigma}-model level should be modified at two (and higher) loop order. The non-static duality is illustrated on the example of cosmological solutions in D {ge} 2 with time-dependent radii of space torus.

Energy Technology Data Exchange (ETDEWEB)

Convective cooling of turbine hot parts using a closed loop system is disclosed. Preferably, the present invention is applied to cooling the hot parts of combustion turbine power plants, and the cooling provided permits an increase in the inlet temperature and the concomitant benefits of increased efficiency and output. In preferred embodiments, methods and apparatus are disclosed wherein air is removed from the combustion turbine compressor and delivered to passages internal to one or more of a combustor and turbine hot parts. The air cools the combustor and turbine hot parts via convection and heat is transferred through the surfaces of the combustor and turbine hot parts.

International Nuclear Information System (INIS)

Post-irradiation annealing was used to help identify the role of radiation-induced segregation (RIS) in irradiation-assisted stress corrosion cracking (IASCC) by preferentially removing dislocation loop damage from proton-irradiated austenitic stainless steels while leaving the RIS of major and minor alloying elements largely unchanged. The goal of this study is to better understand the underlying mechanisms of IASCC. Simulations of post-irradiation annealing of RIS and dislocation loop microstructure predicted that dislocation loops would be removed preferentially over RIS due to both thermodynamic and kinetic considerations. To verify the simulation predictions, a series of post-irradiation annealing experiments were performed. Both a high purity 304L (HP-304L) and a commercial purity 304 (CP-304) stainless steel alloy were irradiated with 3.2 MeV protons at 360 deg. C to doses of 1.0 and 2.5 dpa. Following irradiation, ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the objectives, background, technical progress, and status of ANL electric vehicle battery R D tasks for DOE-EHP during the period of January 1 through March 31, 1991. The work is organized into the following six task areas: Project management; battery systems technology; lithium/sulfide batteries; advanced sodium/metal chloride battery; aqueous batteries; and EV Battery performance/life evaluation.

International Nuclear Information System (INIS)

The radiation dose to a series of adult and paediatric patients undergoing cardiac catheterisations and adults having percutaneous transluminal coronary angioplasty has been measured/determined directly using lithium fluoride thermoluminescent dosemeters and indirectly using an air ionisation chamber which indicated exposure-area product. Somatic and genetic risks are estimated from the dosimetry results. It is suggested that the magnitude of the radiation hazard is negligible compared with other clinical hazards associated with these procedures. (author).

Energy Technology Data Exchange (ETDEWEB)

Crystalline {alpha}-Fe{sub 2}O{sub 3} powder was prepared by the mechanical milling of crystalline {alpha}-FeOOH at room temperature in air. This result means that crystalline {alpha}-FeOOH is dehydrated by mechanical milling at room temperature. The obtained {alpha}-Fe{sub 2}O{sub 3} powder worked as a rechargeable electrode material in lithium ion conductive organic electrolytes. The electrodes exhibited high discharge capacities of over 1000mAhg{sup -1} corresponding to 6 Li per {alpha}-Fe{sub 2}O{sub 3} at potentials ranging from the open circuit potential to 0.5V (versus Li{sup +}/Li) in the first discharging (lithium insertion) process. This suggests that the valence deviation from Fe{sup 3+} in {alpha}-Fe{sub 2}O{sub 3} to Fe{sup 0} may be caused by electrochemical reduction. In contrast, after the first discharge, the electrodes exhibited high charge capacities of more than 700mAhg{sup -1} corresponding to 4.2 Li per {alpha}-Fe{sub ...

Energy Technology Data Exchange (ETDEWEB)

Nano-sized particles of a lithium ion conductive solid electrolyte, LiTi{sub 2}(PO{sub 4}){sub 3}, were prepared by laser ablation. The obtained particles were ca. 10nm in diameter. X-ray powder diffraction and Raman spectroscopy showed that they were amorphous with local structure similar to the crystalline counterpart. They were crystallized by the heating at ca. 630{sup o}C. (author)

International Nuclear Information System (INIS)

Experimental results are presented on the quasi-statistic polarization reversal and on the effect of high dc electric field on the behaviour of LiNH_4SO_4 and LiND_4SO_4 monocrystals, namely in the vicinity of the II-III phase transformation.

International Nuclear Information System (INIS)

Lithium Ceramics offer tremendous potential as a source for the production of tritium ("3H) for fusion power reactors. Their successful application will depend to a great extent upon the diffusion properties of the "6Li within the matrix. Consequently knowledge of "6Li concentration gradients in the ceramic matrices is an important requirement in the continued development of the technology. In this investigation, the neutron depth profile (NDP) technique has been applied to the study of concentration profiles of "6Li in lithium aluminate ceramics, doped with 1.8%, 50% and 95% "6Li isotopic concentrations. Specimen for analysis were prepared at Battelle (PNL) as pellet discs. Samples for diffusion studies were arranged as diffusion couples in the following manner: 1.8% "6Li discs/85% "6Li powder. Experiments were performed at the Texas A and M Nuclear Science Center Reactor Building, utilizing 1 MW equivalent thermal neutron fluxes 3x10"1"1 ...

Energy Technology Data Exchange (ETDEWEB)

Chemical looping combustion is a novel technology that can be used to meet the demand on energy production without CO{sub 2} emission. To improve CO{sub 2} capture efficiency in the process of chemical looping combustion of coal, a prototype configuration for chemical looping combustion of coal is made in this study. It comprises a fast fluidized bed as an air reactor, a cyclone, a spout-fluid bed as a fuel reactor and a loop-seal. The loop-seal connects the spout-fluid bed with the fast fluidized bed and is fluidized by steam to prevent the contamination of the flue gas between the two reactors. The performance of chemical looping combustion of coal is experimentally investigated with a NiO/Al{sub 2}O{sub 3} oxygen carrier in a 1 kW{sub th} prototype. The experimental results show that the configuration can minimize the amount of residual char entering into the ...

Science.gov (United States)

In vertebrates, the positioning of the internal organs relative to the midline is asymmetric and evolutionarily conserved. A number of molecules have been shown to play critical roles in left-right patterning. Using representational difference analysis to identify genes that are differentially expressed on the left and right sides of the chick embryo, we cloned chick Claudin-1, an integral component of epithelial tight junctions. Here, we demonstrate that retroviral overexpression of Claudin-1, but not Claudin-3, on the right side of the chick embryo between HH stages 4 and 7 randomizes the direction of heart looping. This effect was not observed when Claudin-1 was overexpressed on the left side of the embryo. A small, but reproducible, induction of Nodal expression in the perinodal region on the right side of the embryo was noted in embryos that were injected with Claudin-1 retroviral particles on their right sides. However, no changes in Lefty,Pitx2 or cSnR ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility of using three different solid fuels in chemical-looping combustion (CLC) has been investigated using NiO as oxygen carrier. A laboratory fluidized-bed reactor system for solid fuel was used, simulating a chemical-looping combustion system by exposing the sample to alternating reducing and oxidizing conditions. In each reducing phase 0.2g of fuel was added to the reactor containing 20g oxygen carrier. The experiments were performed at 970{sup o}C. Compared to previously published results with other oxygen carriers the reactivity of the used Ni-particles was considerably lower for the high-sulphur fuel and higher for the low-sulphur fuel. Much more unconverted CO was released and the fuel conversion was much slower for high-sulphur fuel such as petroleum coke, suggesting that the nickel-based oxygen carrier was deactivated by the presence of sulphur. The NiO particles also showed good reactivity with methane and a syngas mixture ...

International Nuclear Information System (INIS)

In-reactor testing of bolt-loaded compact tension specimens was performed in 360 C water. New data confirms previous results that high irradiation levels reduce SCC resistance in Alloy X-750. Low boron heats show improved IASCC (irradiation-assisted stress corrosion cracking). Alloy 625 is resistant to IASCC. Microstructural, microchemical, and deformation studies were carried out. Irradiation of X-750 caused significant strengthening and ductility loss associated with formation of cavities and dislocation loops. High irradiation did not cause segregation in X-750. Irradiation of 625 resulted in formation of small dislocation loops and a fine body-centered-orthorhombic phase. The strengthening due to loops and precipitates was apparently offset in 625 by partial dissolution of #gamma# precipitates. Transmutation of boron to helium at grain boundaries, coupled with matrix strengthening, is believed to be responsible for ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 deg. C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed at a higher temperature. The release of ...

Science.gov (United States)

Chemical looping combustion (CLC) is a process in which an oxygen carrier is used for fuel combustion instead of air or pure oxygen as shown in the figure below. The combustion is split into air and fuel reactors where the oxidation of the oxygen carrier and the reduction of the oxidized metal occur respectively. The CLC system provides a sequestration-ready CO2 stream with no additional energy required for separation. This major advantage places combustion looping at the leading edge of a possible shift in strict control of CO2 emissions from power plants. Research in this novel technology has been focused in three distinct areas: techno-economic evaluations, integration of the system into power plant concepts, and experimental development of oxygen carrier metals such as Fe, Ni, Mn, Cu, and Ca. Our recent thorough literature review shows that multiphase fluid dynamics modeling for CLC is not available in the open literature. ...

International Nuclear Information System (INIS)

The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of higher than 2 W/m K were obtained using large ...

Energy Technology Data Exchange (ETDEWEB)

The high temperature solid-state reaction between LiNiO{sub 2} and V{sub 2}O{sub 3} (or V{sub 2}O{sub 5}) in air used to prepare LiNiVO{sub 4} has been further studied. This quaternary Li-Ni-V-O reaction is strongly dependent on reaction temperature and lithium stoichiometry in Li{sub x}Ni{sub 2-x}O{sub 2} and has produced a highly crystalline LiNiVO{sub 4} material whose structure has been confirmed to be an inverse spinel by Rietveld analysis with a Bragg R-factor of 1.18 in the absence of crystal orientation preference. The cell performance of LiNiVO{sub 4} prepared at various temperatures or by varying x-values in Li{sub x}Ni{sub 2-x}O{sub 2} has been examined in lithium coin cells and indicated that preparation at low temperatures or when x=0.89 provided an electrode material with higher cell capacity. (orig.)

International Nuclear Information System (INIS)

Liquid metal cooling for the first wall and blanket of a magnetic confinement fusion reactor has various advantages. However, it has the disadvantages of large magnetohydrodynamic pressure drops and heat transfer deterioration under a strong magnetic field. Thus, the present authors have proposed cooling with a helium-lithium annular mist flow as well as the cooling with a liquid metal boiling flow, and as fundamental studies, investigated the effect of a magnetic field on the flow characteristics and heat transfer of liquid metal two-phase systems since the 1970s. In the present paper we summarize the important findings obtained from our experimental studies for (i) an air-mercury stratified flow in a horizontal rectangular channel, (ii) a helium-lithium annular mist flow in a horizontal rectangular channel, (iii) the mercury pool boiling on a horizontal surface, and (iv) air-mercury upward flows in a vertical circular tube. Based on the ...

International Nuclear Information System (INIS)

Spherical nanostructured Si/C composite was prepared by spray drying technique, followed by heat treatment, in which nanosized silicon and fine graphite particles were homogeneously embedded in carbon matrix pyrolyzed by phenol formaldehyde resin. Cyclic voltammetry tests showed two pairs of redox peaks corresponding to lithiation and delithiation of Si/C composite. The Si/C composite exhibited a reversible capacity of 635 mAh g"-"1 and good cycle performance used in lithium ion batteries. To improve cycle performance of this Si/C composite further, the carbon-coated Si/C composite was synthesized by the second spray drying and heat treatment processing. The cycle performance of carbon-coated Si/C composite was improved significantly, which was attributed to the formation of stable SEI passivation layers on the outer surface of carbon shell which protected the bared silicon from exposing to electrolyte directly.

Energy Technology Data Exchange (ETDEWEB)

Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} thin films were successfully prepared by the solution deposition using lithium acetate, aluminum nitrate, ammonium dihydrogen phosphate and titanium butoxide as starting materials. The structure, surface morphology, electrochemical window, and ionic conductivity of the films were studied by X-ray diffraction, scanning electron microscopy, cyclic voltammetry and AC impedance. The results showed that Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} thin films annealed between 750 deg. C and 900 deg. C prepared by this method were well crystallized, homogenous and crack-free. The electrochemical window was beyond 2.4 V and the ionic conductivity was approximately 1.57x10{sup -5} S/cm at room temperature for the film annealed at 800 deg. C for 30 min.

Science.gov (United States)

The Energy crisis happens to be one of the greatest challenges we are facing today. In this view, much effort has been made in developing new, cost effective, environmentally friendly energy conversion and storage devices. The performance of such devices is fundamentally related to material properties. Hence, innovative materials engineering is important in solving the energy crisis problem. One such innovation in materials engineering is porous materials for energy storage. Porous electrode materials for lithium-ion batteries (LIBs) offer a high degree of electrolyte-electrode wettability, thus enhancing the electrochemical activity within the material. Among the porous materials, mesoporous materials draw special attention, owing to shorter diffusion lengths for Li+ and electronic movement. Nanostructured mesoporous materials also offer better packing density compared to their nanostructured counterparts such as nanopowders, nanowires, nanotubes etc., thus ...

Energy Technology Data Exchange (ETDEWEB)

Lithium hexa-fluoro-phosphate LiPF{sub 6} is recommended for the replacement of the toxic LiAsF{sub 6} and the explosive perchlorates (like LiClO{sub 4}) in rechargeable lithium electrochemical generators. The aim of this work is to develop a new method of synthesis of this salt and to check its stability with respect to carbonated solvents: ethylene carbonate (EC), propylene carbonate (PC) and dimethyl-carbonate (DMC) in already optimized EC/DMC and PC/DMC binary mixtures. Two methods using HPF{sub 6} are proposed: the first one uses the direct neutralization of this commercial acid by LiOH in aqueous, alcoholic or acetonitrile environment, while in the second one LiPF{sub 6} is obtained from pyridinium hexa-fluoro-phosphate synthesized from HPF{sub 6} using a new and simple protocol. (J.S.) 24 refs.

International Nuclear Information System (INIS)

In many experiments involving fast neutrons generated in nuclear reactions initiated by accelerator produced charged particle beams, it is important to be able to determine accurately the neutron yield from the target. A detector suitable for such applications should have: a constant efficiency over a large energy range; a fast time response; and the ability to discriminate between gamma rays and neutrons. The authors have constructed a open-quotes black neutron detectorclose quotes based on the design of Poenitz that has these characteristics. At the Lowell Van de Graaff accelerator laboratory neutrons are produced via the "7Li(p,n)"7Be reaction using a pulsed proton beam which impinges on metallic lithium targets. The pulsed beam enables the detector to be used in a time-of-flight spectrometer. Use of BC501 liquid scintillator permits neutron-gamma discrimination. The scintillator is viewed by five RCA 48796 photo tubes. The detector is housed in a massive shield ...

DEFF Research Database (Denmark)

Polyacrylonitrile (PAN)-based polymer electrolytes have obtained considerable attention due to their fascinating characteristics such as appreciable ionic conductivity at ambient temperatures and mechanical stability. This study is based on the system PAN-ethylene carbonate (EC)-propylene carbonate (PC)-lithium trifluoromethanesulfonate (LiCF3SO3). The composition 15 mol% PAN-42 mol% EC-36 mol% PC-7 mol% LiCF3SO3 has shown a maximum room temperature conductivity of 1.2 x 10(-3) stop S cm(-1) stop. Also, it was possible to make a thin, transparent film out of that composition. Cells of the form, Li/PAN-EC-PC-LiCF3SO3/polypyrrole (PPy)-alkylsulfonate (AS) were investigated using cyclic voltammetry and continuous charge-discharge tests. When cycled at low scan rates, a higher capacity could be obtained and well-defined peaks were present. The appearance of peaks elucidates the fact that redox reactions occur completely. This well proves the reason for higher capacity. ...

Energy Technology Data Exchange (ETDEWEB)

A black neutron detector of novel design has been constructed and tested as a neutron flux monitor. The neutron time-of-flight (TOF) technique was used to measure the zero degree neutron spectrum from a subnanosecond pulsed proton beam on a thick metallic lithium target. We describe the detector, discuss the shielding arrangement and electronics, determine the low-energy cut-off. We calculate the efficiency, show spectra and compare measured zero degree differential cross-section of the {sup 7}Li(p, n{sub 0}){sup 7}Be reaction with recommended published cross-sections. (orig.).

Energy Technology Data Exchange (ETDEWEB)

A process is claimed for selectively preparing a mixture of two-carbon atom oxygenated hydrocarbons, namely, acetic acid, ethanol and acetaldehyde, by continuously contacting a gaseous reaction mixture containing hydrogen and carbon monoxide with a solid catalyst comprising rhodium in combination with one or more alkali metals selected from the group consisting of lithium, potassium, cesium and rubidium at reaction conditions correlated so as to favor the formation of a substantial proportion of such two-carbon atom products.

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

Energy Technology Data Exchange (ETDEWEB)

Aluminium-lithium extrusions possess high inhomogeneity of properties across the cross section. Mechanical properties such as R{sub p0,2}, R{sub m} and hardness, but also fatigue properties, change their value in dependence with the cross section position where test specimens were taken. Positions, where extreme values of properties are measured, are characteristic for a given extrusion shape. The positions with different properties have different structure and texture. Properties and structure inhomogeneity is affected mainly by extrusion shape and heat treatment parameters. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The external background radiation level in and around the Atomic Energy Research Establishment (AERE) in Dhaka has been measured. The measurements were performed using lithium fluoride (LiF) thermoluminescence dosemeters (TLD-100) at 32 locations, all one metre above the ground. The annual average dose rate measured in the AERE environs was 1.74+-0.23 mGy.y/sup -1/ in air, based on analysis of thermoluminescence dosemeter data collected from 1982 to 1984.

Energy Technology Data Exchange (ETDEWEB)

High-precision laser spectroscopy on lithium isotopes is of fundamental interest, experimentally as well as theoretically. The lithium atom has long served as a test system for the calculation of various atomic properties in few-electron atoms and significant advances have been made in the last decade[1-3]. Recently, calculations of transition energies for the 22S1/2 -> 32S1/2 and the 22S1/2 -> 22P1/2, 3/2 transitions and of the mass-dependant isotope shift (IS) in these transitions have been reported with a relative accuracy of better than 1 X 10-7 and 5 x 10-6, respectively[4, 5]. These calculations are the foundation for experimental efforts, currently underway at GSI Darmstadt, Germany, to determine the root-mean-square (rms) charge radius of the unstable lithium isotopes[6, 7]. The basic principle is that if all mass-dependent contributions to the IS can be calculated with sufficient accuracy, the ...

International Nuclear Information System (INIS)

Reactor Power Measurement is an essential part of the Reactor Power Control Loop in PHWRs. None of the available power measuring sensor offers characteristics which allow their direct use in the Reactor Power Control Loop. Thermal power, which is considered as relatively accurate, suffers from measurement delays and is used only as reference. Neutronic power sensors like Ion Chambers and Self Powered Neutron Detectors (SPNDs) which sense instantaneous power suffer from inaccuracies. A technique is required which makes use of both types-reference power and instantaneous power to extract real power information from the signals. This paper describes techniques to calibrate (correct) neutronic power that with the thermal reference power signals. The paper also brings out limitation of the calibration technique. (author)

Science.gov (United States)

An explanation is given of what a loop heat pipe (LHP) is, and how it works. It is then shown that neutron imaging (both real time neutron radioscopy and single exposure neutron radiography) is an effective experimental tool for the study of LHPs. Specifically, neutron imaging has helped to identify and correct a cooling water distribution problem in the condenser, and has enabled visualization of two-phase flow (liquid and vapor) in various components of the LHP. In addition, partial wick dry-out, a phenomenon of great importance in the effective operation of LHPs, is potentially identifiable with neutron imaging. It is anticipated that neutron radioscopy and radiography will greatly contribute to our understanding of LHP operation, and will lead to improvement of LHP modeling and design. PMID:15246420

Energy Technology Data Exchange (ETDEWEB)

An explanation is given of what a loop heat pipe (LHP) is, and how it works. It is then shown that neutron imaging (both real time neutron radioscopy and single exposure neutron radiography) is an effective experimental tool for the study of LHPs. Specifically, neutron imaging has helped to identify and correct a cooling water distribution problem in the condenser, and has enabled visualization of two-phase flow (liquid and vapor) in various components of the LHP. In addition, partial wick dry-out, a phenomenon of great importance in the effective operation of LHPs, has been identified with neutron imaging. It is anticipated that neutron radioscopy and radiography will greatly contribute to our understanding of LHP operation, and will lead to improvement of LHP modeling and design.

Energy Technology Data Exchange (ETDEWEB)

This paper is devoted to the coordination of secondary voltage control and adaptive parameters resetting of the power system stabilizer, in order to increase stability, margins in real time operation. Secondary voltage control and the power system stabilizer are two control loops, which affect the same system parameter on different bases - that parameter is the voltage set-point of the automatic voltage regulator. It was found that their effects were complementary. In that way, through the proper coordination of actions of these two control loops open up a wide range of possibilities for ensuring the stability of bulk power systems in real time. For the establishment of this coordination, an on-line sequential algorithm is proposed which is based on adaptive resetting of the voltage set-point of the automatic voltage regulator and the PSS parameters. The efficiency of the proposed algorithm is confined through simulations on a real-life ...

International Nuclear Information System (INIS)

A cold-leg small-break loss-of-coolant accident (SBLOCA) experiment was performed on the PACTEL facility to study the behavior of natural circulation in a VVER-440 reactor geometry. The facility is a volumetrically scaled (1:305) integral test loop simulating the VVER-440 reactors used in Finland. The test results were used to assess the computer codes RELAP5/MOD3.1 and APROS 3.0 for VVER reactors. The behavior of the horizontal steam generator and the effect of the hot-leg loop seal were of particular interest. The specific parameters to be compared included the primary pressure and the downcomer mass flow rate.

International Nuclear Information System (INIS)

Decay heat removal capability under boiling condition was studied using an LMFBR fuel subassembly mockup loop. The sodium flow was driven by natural convection through the loop in which was installed a 37-pin bundle heated electrically over a length of 45 cm. The heat flux furnished by the pins was increased stepwise, upon which the two-phase flow regime changed from bubble to slug flow and then to annular or annular mist flow. Dryout occurred even in slug flow regime, but only momentarily, and permanent dryout was not observed before establichment of annular flow. A suitable criterion for permanent dryout is considered to be 0.5 average exit sodium vapor quality. The results indicated that upon occurrence of sodium boiling, the coolability of fuel subassembly would be maintained by natural convection after reactor shutdown. (author).

Energy Technology Data Exchange (ETDEWEB)

Many existing methods of identifying the optimum sites for installing power system stabilizers (PSSs) in multi-machine systems are restricted to the sequential PSS application, which considers the enhancement of damping of just one critical electromechanical mode at a time; the eigenstructure analysis of the open-loop system, which does not take the control matrix (i.e., the B matrix in the linearized model x = Ax + Bu for power systems) into consideration. This paper presents a method of identifying the optimum sites for installing power system stabilizers. The advantages of this method are: it can identify the optimum sites for installing PSSs so that several electrochemical modes are damped out simultaneously; it takes both the eigenstructure of the open-loop system and the control matrix into consideration.

British Library Electronic Table of Contents (United Kingdom)

Bent specimens of A533B steel (0.16wt% Cu) were irradiated at 290degreeC to 1dpa with 6.4MeV Fe3+ ions. Calculated tensile stresses at the irradiated surface were set to 0, 250, 500 and 750MPa. The specimens were subjected to hardness measurements, transmission electron microscopy (TEM) observations and three-dimensional atom probe (3DAP) analysis. The radiation-induced hardening decreased with increasing stress to 500MPa which was near the yield strength. TEM and 3DAP results showed that well-defined dislocation loops and solute clusters were formed. The diameter of dislocation loops increased and the number density decreased when the stress was applied, whereas the diameter and number density of solute clusters decreased. The hardening was mainly attributed to solute cluster formation. A...

International Nuclear Information System (INIS)

An Fe-15Cr-20Ni ternary model alloy and a Type 316 stainless steel were irradiated by dual-ions at 1 to 50 appm of He/dpa ratios, to investigate the helium effects on microstructural development in austenitic alloys under irradiation. Quantitative analysis on resultant microstructures revealed that the Frank loop nucleation rate and the network dislocation density positively correlate and Frank loop growth rate negatively correlate with the He/dpa ratio, while the cavity growth rate has its peak at an intermediate helium injection rate. Although He/dpa dependence of various microstructural features were similar for the model alloy and the 316SS, the rates of their development and the mechanism which had assisted cavity growth were significantly different in these two materials. (orig.).

Energy Technology Data Exchange (ETDEWEB)

At the reference plant (Wolsung unit No. 1) a manual poison sampling system is provided to periodically sample gadolinium from each tank and analyze it in the laboratory to provide assurance that adequate poison concentration in each tank is maintained. The AECB required a continuous, on-line monitoring system. On Wolsung unit No. 2, process piping adapter and new instrument loops added to the Liquid Injection Shutdown System(LISS) which is part of SDS2. The new instrument loops continuously monitor SDS2 poison conductivity and initiate an alarm when the poison concentration is too low. 8 refs., 1 fig. (author).

CERN Document Server

In this article we present the complete resummation of the leading chirally-enhanced corrections stemming from gluino-squark, chargino-sfermion and neutralino-sfermion loops in the MSSM with non-minimal sources of flavor-violation. We compute the finite renormalization of fermion masses and the CKM matrix induced by chirality-flipping self-energies. In the decoupling limit Msusy>>v, which is an excellent approximation to the full theory, we give analytic results for the effective gaugino(higgsino)-fermion-sfermion and the Higgs-fermion-fermion vertices. Using these vertices as effective Feynman rules, all leading chirally-enhanced corrections can consistently be included into perturbative calculations of Feynman amplitudes. We also give a generalized parametrization for the bare CKM matrix which extends the classic Wolfenstein parametrization to the case of complex parameters lambda and A.

International Nuclear Information System (INIS)

We present a new relativistic bound-state formalism for two interacting Fermi-Dirac particles. The kernel of the integral equation for the bound-state system is generated by summing Feynman scattering amplitudes and multiplying by a bound-state amplitude. The method is illustrated through calculations of the hyperfine and fine splittings of positronium up to order #alpha#"5. Our calculations of the one-loop contributions are carried out in the explicitly covariant Feynman gauge. We also present new results for the hyperfine and fine splittings in positronium to order #alpha#"5 for arbitrary principal quantum number n, which are easily obtained owing to the virtue of conceptual and calculational simplicity of our formalism. In addition, we present the one-loop renormalization scheme in our formalism. (author).

Energy Technology Data Exchange (ETDEWEB)

A family of mixed LiCo{sub y}Ni{sub (1-y)}VO{sub 4} (y=0.2, 0.5 and 0.8) compounds of potential use as high voltage cathode materials in lithium batteries, has been synthesized and characterized. The X-ray diffraction analysis showed that these compounds adopt an inverse spinel structure where in average 85% of the Ni{sup 2+} and Co{sup 2+} ions occupy octahedral sites and the other 15% occupy tetrahedral sites with the V{sup 5+} ions, although this occupation share is somewhat influenced by the preparation temperature. The annealing temperature plays also a key role in determining the particle size, as demonstrated by scanning electron microscope analysis. Cycling voltammetry tests showed that the lithium insertion-deinsertion process in the LiCo{sub y}Ni{sub (1-y)}VO{sub 4} electrode materials occurs reversibly around 4.3-4.4 V vs. Li, as also confirmed by cycling tests. The cycling capacity is somewhat modest; however, the trend of the ...

Energy Technology Data Exchange (ETDEWEB)

Lithium-ion batteries are now considered to be the technology of choice for future hybrid electric and full electric vehicles to address global warming. LiCoO{sub 2} has been the most widely used cathode material in commercial lithium-ion batteries. Since LiCoO{sub 2} has economic and environmental issues, intensive research has been directed towards the development of alternative low cost, environmentally friendly cathode materials as possible replacement of LiCoO{sub 2}. Among them, spinel LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} material is one of the promising and attractive cathode materials for next generation lithium-ion batteries because of its high voltage (4.7 V), acceptable stability, and good cycling performance. Research advances in high voltage spinel LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} are reviewed in this paper. Developments in synthesis, structural characterization, effect of doping, and effect of coating are ...

Energy Technology Data Exchange (ETDEWEB)

A flexible battery is printed on paper by screen-printing a zinc/carbon/polymer composite anode on one side of the sheet, polymerising a poly(3,4-ethylenedioxythiophene) (PEDOT) cathode on the other side of the sheet, and applying a lithium chloride electrolyte between the two electrodes. The PEDOT cathode is prepared by inkjet printing a pattern of iron(III)p-toluenesulfonate as a solution in butan-1-ol onto paper, followed by vapour phase polymerisation of the monomer. The electrolyte is prepared as a solution of lithium chloride and lithium hydroxide and also applied by inkjet printing on to paper, where it is absorbed into the sheet cross-section. Measurements on a zinc/carbon-PEDOT/air battery in a similar configuration on a polyethylene naphthalate substrate shows a discharge capacity of up to 1.4 mAh cm{sup -2} for an initial load of 2.5 mg zinc, equivalent to almost 70% of the zinc content of the anode, which ...

Science.gov (United States)

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network functions as both ...

Energy Technology Data Exchange (ETDEWEB)

The paper describes a lithium battery researched on under the Moonlight Project which is a long life secondary battery with high energy density and high power density. Using as a base a Li4SiO4 system which exhibits stable and high Li[sup +] conductivity as solid electrolyte material, partial Si[sup 4+] is replaced with divalent ions such as B[sup 3+] and Al[sup 3+] or divalent ions such as Ni[sup 2+] and Co[sup 2+], by which Li[sup +] for electric charge compensation can be increased and conductivity is enhanced. As to a LiTi2P3O12 system, Ti[sup 4+] is replaced with Sc[sup 3+] and Y[sup 3+]. In both systems, by replaCing Si[sup 4+] or Ti[sup 4+] with trivalent metal ions and increasing mobile Li[sup +], those with ion conductivity exceeding that at 300[degree]C, 10[sup -3]Scm[sup -1], can be developed. TiS2 and NiPS3 are prepared as cathode material and miniature cells are trially fabricated. Various polarization phenomena are observed and a lot of improvements ...

Energy Technology Data Exchange (ETDEWEB)

In order to discuss effects of lithium iodide (LiI) doping on condensation structure of brown coals during heating, spectral changes were measured by using an in-situ FT-IR. It was found that the LiI doping accelerates weight reduction due to heating, and the doping effect is affected by coal structure. Both of Loy Yang (LY) coal and its LiI doped coal (DLY) had absorption intensity of the FT-IR spectra decreased with rising temperature, and the absorption center belonging to an OH group shows different shifts between the LY and DLY coals. This indicates that the LiI doping has affected the change in hydrogen bonding patterns associated with heating. Both of South Banko (SB) and LY coals had the absorption spectral intensity in the OH group decreased as the weight reduction (conversion) rate increased. Reduction in the OH groups associated with heating is caused by volatilization and condensation reaction in light-gravity fraction. However, in the case of equal ...

Energy Technology Data Exchange (ETDEWEB)

A small-sized inexpensive carbon dioxide gassensor was prepared using LiTi2 (PO4)3 +0.2Li3PO4 as lithium-ion conductive, solid electrolyte and its detectability and the effects of co-existing gases were examined. The above compound was obtained by the method where a powdery mixture of Li2CO3, TiO2, (NH4)H2PO4 and Li3PO3 was molded in the presence of a sintering assistant, subjected to hydrostatic press, and sintered. Measurements were made on the relation between CO2 concentration and the electromotive force of the CO2 sensor made of the compound and the influence of concentration of coexisting NO2, SO2 or CH4 on the electromotive force. The results are summarized as follows. A linear relation exists between the electromotive force and the CO2 concentration in the range from 80ppm to 1% to show a good agreement between theoretical and experimental results. Coexistence of NO2 the range of 100-4500ppm has no influence on the electromotive force. Coexistence of ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is an indirect combustion technology with inherent separation of the greenhouse gas CO{sub 2}. The feasibility of using NiO as an oxygen carrier during chemical-looping combustion of coal has been investigated experimentally at 800-960{degree}C in the present work. The experiments were carried out in a fluidized bed, where the steam acted as the gasification-fluidization medium. Coal gasification and the reaction of oxygen carrier with the water gas take place simultaneously in the reactor. The oxygen carrier particles exhibit high reactivity above 900{degree}C, and the dry basis concentration of CO{sub 2} in the exit gas of the reactor is nearly 95%. The flue gas composition as a function of the reactor temperature and cyclic reduction number is discussed. At 800-960{degree}C, the dry basis concentration of CO{sub 2} in the flue gas presents a monotonously increasing trend, whereas the dry basis concentration of CO, ...

Energy Technology Data Exchange (ETDEWEB)

The Cutkosky rules are generalized to include tachyons. A consequence is that Lorentz-invariant interacting theories which possess tachyons cannot obey even the weakest possible form of unitarity beyond the tree level. The problem (although not the cutting rules) is shown to extend to bosonic string theory. Thus unitarity cannot be used to determine the range of modular integration in bosonic string loop amplitudes.

Energy Technology Data Exchange (ETDEWEB)

In the framework of the equivalence theorem the one-loop helicity amplitudes and cross section for the double Higgs production process {gamma}{gamma}{yields}HH are calculated. It is shown that the cross section is measurable at TeV {gamma}{gamma} colliders and is marginally sensitive to the triple-Higgs variation. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Using a simple model for soft self-consistent nonperturbative string fragmentation-recombination loops, we find that, in an open-string theory, ground-state particles necessary for the standard model either become tachyons or acquire large (Planck-scale) masses, making them unacceptable for sub-Planck-scale phenomenology. No comparable difficulties are evident for closed-string theories.

Energy Technology Data Exchange (ETDEWEB)

We investigate the scope of all relevant production modes of charged Higgs bosons in the MSSM, with mass larger than the one of the top quark, at future Linear Colliders operating in {gamma}{gamma} mode at the TeV energy scale. Final states with one or two H{sup {+-}} bosons are considered, as produced by both tree- and loop-level interactions. (orig.)

International Nuclear Information System (INIS)

This paper deals with construction types of high temperature heat exchangers, their circulation loops and temperature differences. Most attention is given to gas dynamics, convective heat transfer, convection and radiant heat transfer interaction in high temperature heat exchangers. The ways of heat transfer augmentation and efficient heat exchanger construction are discussed.

Energy Technology Data Exchange (ETDEWEB)

We report on the calculation of multi-loop Feynman integrals for single-scale problems by means of difference equations in Mellin space. The solution to these difference equations in terms of harmonic sums can be constructed algorithmically over difference fields, the so-called {pi}{sigma}{sup *}-fields. We test the implementation of the Mathematica package Sigma on examples from recent higher order perturbative calculations in Quantum Chromodynamics. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Earlier studies have indicated that xylitol may increase the absorption and urinary excretion of dietary oxalate. It has also been indicated that xylitol increases the absorption of calcium. Intestinal absorption of lead, a divalent contaminant in the diet, is in many respects similar to that of calcium. The purpose of this study was to evaluate the effects of xylitol on the intestinal absorption of lead using two different approaches: the in situ ligated intestinal loop technique in cockerels and gastric gavage in mice.