Energy Technology Data Exchange (ETDEWEB)

A solar thermophotovoltaic (STPV) system has both terrestrial and space applications because thermal energy storage can be utilized. Excellent properties (heat of fusion=1800 j/gm and melting temperature=1680 K) make silicon the ideal thermal storage material for an STPV system. Using a one dimensional model with tapering of the silicon storage material, it was found that several hours of running time with modest lengths ({approximately}15 cm) of silicon are possible. Calculated steady-state efficiencies for an STPV system using an Er-YAG selective emitter and ideal photovoltaic (PV) cell model are in the range of 15{percent}{endash}17{percent}. Increasing the taper of the storage material improves both efficiency and power output. {copyright} {ital 1996 American Institute of Physics.}

Energy Technology Data Exchange (ETDEWEB)

III-V semiconductors, GaAs and in particular InGaP, are used in many different electronic applications, such as high power and high frequency devices, laser diodes and high brightness LED. Their direct bandgap and high reliability make them ideal candidates for the realisation of high efficiency solar cells: in the past years they have been successfully used as power sources for satellites in space, where they are able to produce electricity from sunlight with an overall efficiency of around 30%. Nowadays, the use of arsenides and phosphides as photovoltaic (PV) devices is confined only to space applications since their price is much higher than conventional Si flat panel modules, the leading PV market technology. But with the introduction of multijunction solar cells capable of operating in high concentration solar light, the area and, therefore, the cost of these cells can be ...

Energy Technology Data Exchange (ETDEWEB)

The National Center for Photovoltaics sponsored the 17th Workshop on Crystalline Silicon Solar Cells & Modules: Materials and Processes, held in Vail, CO, August 5-8, 2007. This meeting provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. The theme of this year's meeting was 'Expanding Technology for a Future Powered by Si Photovoltaics.'

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the progress of the Solid State Photovoltaic Research Branch of the Solar Energy Research Institute (SERI) from October 1, 1988, through September 30,l 1989. Six technical sections of the report cover these main areas of SERIs in-house research: Semiconductor Crystal Growth, Amorphous Silicon Research, Polycrystalline Thin Films, III-V High-Efficiency Photovoltaic Cells, Solid-State Theory, and Laser Raman and Luminescence Spectroscopy. Sections have been indexed separately for inclusion on the data base.

Energy Technology Data Exchange (ETDEWEB)

Topics covered include various aspects of solar cell fabrication and performance. Aluminium-gallium arsenides, cadmium telluride, amorphous silicon, and copper-indium-gallium selenides are all characterized in their applicability in solar cells.

Science.gov (United States)

This paper discusses a new control strategy for photovoltaic power generation systems with consideration of dynamic characteristics of the photovoltaic cells. The controller estimates internal currents of an equivalent circuit for the cells. This estimated, or the virtual current and the actual voltage of the cells are fed to a conventional Maximum-Power-Point-Tracking (MPPT) controller. Consequently, this MPPT controller still tracks the optimum point even though it is so designed that the seeking speed of the operating point is extremely high. This system may suit for applications, which are installed in rapidly changeable insolation and temperature-conditions e.g. automobiles, trains, and airplanes. The proposed method is verified by experiment with a combination of this estimating function and the modified Boehringer's MPPT algorithm.

Energy Technology Data Exchange (ETDEWEB)

The current status of non-silicon photovoltaic solar cells is discussed including the identification of current technical and economic issues and future research directions for potential high efficiency low cost technologies. This review covers such advanced materials as CdS/Cu/sub 2/S, CdS/CuInSe/sub 2/, and GaAs homojunction and heterojunction devices; such emerging materials as InP, Zn/sub 3/P/sub 2/ and CdTe; and liquid junction electrochemical photovoltaic cells. An attempt is made to compare the current relative status of these various technologies and to indicate their near term potential where possible. 105 refs.

Energy Technology Data Exchange (ETDEWEB)

The National Center for Photovoltaics sponsored the 15th Workshop on Crystalline Silicon Solar Cells & Modules: Materials and Processes, held in Vail, CO, August 7-10, 2005. This meeting provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. The workshop addressed the fundamental properties of PV silicon, new solar cell designs, and advanced solar cell processing techniques. A combination of oral presentations by invited speakers, poster sessions, and discussion sessions reviewed recent advances in crystal growth, new cell designs, new processes and process characterization techniques, and cell fabrication approaches suitable for future manufacturing demands. The theme of this year's meeting ...

Energy Technology Data Exchange (ETDEWEB)

This final report for the Swiss Federal Office of Energy (SFOE) describes the 23.5 kW photovoltaic installation on the Customs House in Kreuzlingen, Switzerland. The objective of the 'Zollhof' photovoltaic solar power plant is to provide the local population with a 'hands-on' solar cell experience, that, according to the authors, should lead to better understanding of renewable energy technology. The commissioning and initial operation of the installation is commented on, as are the above-average production figures of the plant. The power produced is sold by the local utility to its customers as electricity from renewable resources.

Energy Technology Data Exchange (ETDEWEB)

This book contains the results of an architectural evaluation of building examples with integrated photovoltaic. Danish Building and Urban Research and Danish Technological Institute conducted the work within the framework of Solar Energy Centre Denmark. Seven examples are selected to inspire Danish architects and building owners to use PV in the building environment. The examples come from Denmark and countries (the Netherlands and Germany) with similar building traditions, climate and solar conditions. All the examples demonstrate architectural concepts that integrate photovoltaic as a natural part of the building envelope. (BA)

Energy Technology Data Exchange (ETDEWEB)

This report contains the document control information and abstracts for Solar Energy Research Institute (SERI) Photovoltaic (PV) Program publications resulting from SERI's subcontracted PV research. The information is presented for reports published or distributed from August 1 through December 31, 1990. In the past, copies of the subcontractor reports were distributed to a broad spectrum of researchers in the field of photovoltaics at a considerable cost to the program. In an attempt to reduce costs and ensure that all researchers receive those current publications that are of specific interest to them, this report will outline these publications, organized by technology, on a regular basis. A list of additional publications and sources is included herein to provide the photovoltaic community with other sources of information. All of the documents represented here are available from the National Technical ...

Energy Technology Data Exchange (ETDEWEB)

The article provides a 1998 updated picture of Italy's and the world's photovoltaic market in terms of produced modules and total installed capacity, as well as market growth forecasts up to 2010. After a short description of the state-of-the-art of cell and module manufacturing, ana analysis of the cost of producing a photovoltaic kw is reported for different plant types: stand-alone plants with energy storage batteries, plants connected to low low voltage networks or intended for supporting medium voltage networks, hybrid plants with diesel sets. The article is concluded by illustrating ENEL's (Electric Power Production Company) engagement in the field of photovoltaic solar energy as regards theoretical studies, research and testing of new technologies, and installing plants; over nearly twenty years of activity, ENEL has designed and built a few hundreds of ...

Science.gov (United States)

This current awareness bulletin announces on a semimonthly basis the current worldwide information entered into the Energy Data Base on all aspects of direct energy conversion. Categories include photovoltaic conversion, magnetohydrodynamic generators, electrohydrodynamic generators, thermoelectric generators, thermionic converters, fuel cells, and miscellaneous converters. An abstract is inclluded with each citation. (WHK)

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the progress of the Basic Sciences Branch of the National Renewable Energy Laboratory (NREL) from October 1, 1989, through September 30, 1990. Six technical sections of the report cover these main areas of NREL's in-house research: Semiconductor Crystal Growth, Amorphous Silicon Research, Polycrystalline Thin Films, III-V High-Efficiency Photovoltaic Cells, Solid-State Theory, and Solid-State Spectroscopy. Each section of the report was written by the group leader principally in charge of the work. The task in each case was to explain the purpose and major accomplishments of the work in the context of the US Department of Energy's National Photovoltaic Research Program plans.

Environmental Research Database

Objectives1. To develop new photoactive materials and fabricate demonstration QD (quantum dot) solar cells. This will be achieved by:~%~1.1. Materials preparation and characterisation of QD/polymer systems~%~1.2. Optimising structures of QDs, nanorods and polymer for quantum yield and charge transfer~%~1.3 Fabricating demonstration QD/polymer solar cells and measuring power conversion efficiencies~%~2. To demonstrate multiexciton generation (MEG) and harvesting within nanostructured QDs. This will involv [continued...]DescriptionWidespread implementation of photovoltaic electricity to meet changing energy demands requires a step-change in the cost of photovoltaic power. This proposal assembles a consortium of chemists, physicists, materials scientists and electrical engineers from The University of Manchester and Imperial College London to address this need through the development of new low-cost, ...

Science.gov (United States)

One of the NASA research activities was to identify, characterize, and simulate a series of technologies that could be used for hydrogen production at NASA Kennedy Space Center (KSC) using locally available sources. This project examined the production of hydrogen from solar energy. To produce hydrogen by water splitting, the operating voltage of conventional photovoltaic (PV) cells cannot supply the overvoltage required. Thus, the objective of this project was to research and develop photoelectrochemical (PEC) cells that can supply the required voltage for water splitting by constructing a multiple bandgap tandem PV cell and a photocatalyst that can be activated by infrared (IR) photons transmitted through the PV cell. The proposed concept is different from conventional PEC water splitting by using multiple band gap combinations. The advantages for this PEC ...

Energy Technology Data Exchange (ETDEWEB)

In this paper we consider properties of the ideal gas of classical (nonquantum) tachyons.

Energy Technology Data Exchange (ETDEWEB)

This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result due to correction coefficient for the ...

Energy Technology Data Exchange (ETDEWEB)

This report beings with a historical overview on the origin and early beginnings of Radiant Energy Power Source for Jet Aircraft. The report reviews the work done in Phase I (Grant DE-FG01-82CE-15144) and then gives a discussion of Phase II (Grant DE-FG01-86CE-15301). Included is a reasonably detailed discussion of photovoltaic cells and the research and development needed in this area. The report closes with a historical perspective and summary related to situations historically encountered on projects of this nature. 15 refs.

Wastenet

... Another solution, hybrid vehicles, combine two sources of energy (electric and chemical), reducing the global consumption of fossil fuels. Fuel cell vehicles are also one of the most promising technologies for the future, with the capacity to use any fuel - hydrogen being the ideal fuel ecologically, but constrained by infrastructure and storage issues. This book explores all these different solutions for moving our vehicles from fossil ...

Energy Technology Data Exchange (ETDEWEB)

Basic information on photovoltaic conversion technology is provided for those unfamiliar with the field. Various types of photovoltaic products and systems currently available off-the-shelf are described. These include products without batteries, battery chargers, power packages, home electric systems, and partial systems. Procedures are given for designing a photovoltaic system from scratch. A few custom photovoltaic systems are described, and a list is compiled of photovoltaic firms which can provide custom systems. Guidance is offered for deciding whether or not to use photovoltaic products. A variety of installations are described and their performance is appraised by the owners. Information is given on various financial incentives available from state and federal governments. Sources of additional information on photovoltaics are ...

Energy Technology Data Exchange (ETDEWEB)

The theoretical performance of ideal single- and multijunction cells are compared at 100xconcentration under a range of cloudless-sky conditions. The sensitivities of device performance to cell temperature and spectral variations are shown to depend on the number of junctions (one, two or three), the way in which the junctions are connected (series, parallel or independent), and the band gaps of the devices. The average performances of all of the multijunction devices surpass that of a single-junction GaAs device, but the inconsistency in performance of some of the multijunction devices is significant for large variations in cell temperature and incident spectrum. The choice of band gap and connection scheme is more important than the number of junctions in determining the consistency of device performance. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The Engineering and Technology Validation Team at the National Renewable Energy Laboratory (NREL) conducts in-situ technical evaluations of polycrystalline thin-film photovoltaic (PV) modules and arrays. This paper focuses on the technical evaluation of Solar Cells, Inc., (SCI) cadmium telluride (CdTe) module and array performance by attempting to correlate individual module and array performance. This is done by examining the performance and stability of the modules and array over a period of more than one year. Temperature coefficients for module and array parameters (P{sub max}, V{sub oc}, V{sub max}, I{sub sc}, I{sub max}) are also calculated.

Energy Technology Data Exchange (ETDEWEB)

Thermophotovoltaic (TPV) converters were developed and tested at the heat source operating temperature of 1,700 K. Rare-earth-doped yttrium aluminum garnet (YAG) and lutetium yttrium aluminum garnet (Lu, YAG) selective emitters, as well as a blackbody emitter, were coupled to InGaAs/InP photovoltaic (PV) cells and bandpass/infrared (IR) reflector filters. YAG-based selective emitters were adopted with Ho, Tm, and Er. PV cells had bandgaps of 0.51, 0.57, and 0.69 eV. Converter energy conversion efficiencies approaching 30%, as well as electrical output power densities near 2 W/cm{sup 2} were demonstrated. The overall performance of the filtered blackbody-based converter was found to be superior to the selective emitter YAG-based converters. The details of the measurements performed on the above converters and their individual components are presented.

Energy Technology Data Exchange (ETDEWEB)

Quaternary semiconductor compounds are ideal candidates for use in monolithic cascade solar cells because the lattice constant and the bandgap of such compounds can be independently varied. The quaternary semiconductor compound Ga[sub 0.83]In[sub 0.17]As[sub 0.67]P[sub 0.33] not only is lattice matched to GaAs and Ge but also provides a current matched top cell for the GaInAsP/Ge monolithic cascade solar cell. Under concentration of 100 suns, the projected efficiency for such a cell is about 34%. The growth of Ga[sub 0.83]In[sub 0.17]As[sub 0.67]P[sub 0.33] lattice matched to GaAs and Ge has been demonstrated. GaInAsP solar cells have been grown on both GaAs and Ge substrates. A GaInAsP on GaAs solar cell with an active area efficiency of 23.2% for 1 sun, AM 1.5 direct illumination has been prepared. A proposed structure for the GaInAsP/Ge ...

CERN Document Server

In this paper we have studied the relation between the intutionistic fuzzy left (respectively right) ideals of {\\Gamma}-semiring and that of operator semiring. Thereafter, we have established that the Lattices of all intutionistic fuzzy left (respectively right) ideal of {\\Gamma}-semiring is equivalent to that of Left operator semiring. We proved that Then there exist an inclusion preserving bijection ({\\mu}_{A,}\\u{psion}_{A})$\\rightarrow$({\\mu}_{B}^{+'},\\u{psion}_{B}^{+'}) between the lattices of all intuitionistic fuzzy right ideals (respectively intuitionistic fuzzy ideals) of S and the lattices of all intuitionistic fuzzy right ideals (respectively intuitionistic fuzzy ideals) of L. Where ({\\mu}_{A},\\u{psion}_{A}) is an intuitionistic fuzzy right (respectively intuitionistic fuzzy ideals) ideal of S. Also we ...

Energy Technology Data Exchange (ETDEWEB)

The availability of polysilicon feedstock has become a major issue for the photovoltaic (PV) industry in recent years. Most of the current polysilicon feedstock is derived from rejected material from the semiconductor industry. However, the reject material can become scarce and more expensive during periods of expansion in the integrated-circuit industry. Continued rapid expansion of the PV crystalline-silicon industry will eventually require a dedicated supply of polysilicon feedstock to produce solar cells at lower costs. The photovoltaic industry can accept a lower purity polysilicon feedstock (solar-grade) compared to the semiconductor industry. The purity requirements and potential production techniques for solar-grade polysilicon have been reviewed. One interesting process from previous research involves reactive gas blowing of the molten silicon charge. As an example, Dosaj et all reported a reduction of metal and ...

British Library Electronic Table of Contents (United Kingdom)

Entorhinal grid cells in mammals fire as a function of animal location, with spatially periodic response patterns. This nonlocal periodic representation of location, a local variable, is unlike other neural codes. There is no theoretical explanation for why such a code should exist. We examined how accurately the grid code with noisy neurons allows an ideal observer to estimate location and found this code to be a previously unknown type of population code with unprecedented robustness to noise. In particular, the representational accuracy attained by grid cells over the coding range was in a qualitatively different class from what is possible with observed sensory and motor population codes. We found that a simple neural network can effectively correct the grid code. To the best of our kn...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This study is devoted to the formation of high-low-level-doped selective emitter for crystalline silicon solar cells for photovoltaic application. We report here the formation of porous silicon under chemical reaction condition. The chemical mixture containing hydrofluoric and nitric acid, with de-ionized water, was used to make porous on the half of the silicon surface of size 125 x 125 cm. Porous and non-porous areas each share half of the whole silicon surface. H{sub 3}PO{sub 4}:methanol gives the best deposited layer with acceptable adherence and uniformity on the non-porous and porous areas of the silicon surface to get high- and low-level-doped regions. The volume concentration of H{sub 3}PO{sub 4} does not exceed 10% of the total volume emulsion. Phosphoric acid was used as an n-type doping source to make emitter for silicon solar cells. The measured emitter sheet resistances at the high- and low-level-doped regions ...

International Nuclear Information System (INIS)

The ternary compound CuInS2 is attractive for solar cells due to its band gap of 1.54 eV which borders the optimum value necessary for conversion of a solar spectrum. Recently, works on thin film cells based on this material (ZnO/CuInS2) has been reported to show efficiency as high as 11.4%. In this paper, the orientation and the morphology of CuInS2 sprayed films are determined by the means of X-ray diffraction and scanning electron microscopy. Sprayed CuInS2 films deposited onto a transparent Pyrex substrate with standard fabrication parameters show a chalcopyrite structure with a preferential orientation (1 1 2). A model based on the calculation of the relative dielectric function ? has been performed in order to obtain the profile of variation of this parameter and to understand the optical behavior of this material via its transmittance and reflectance in visible and near-infrared regions (0.35-2.5 ?m). In the same way, considering the ...

International Nuclear Information System (INIS)

Ultraviolet light can be used to immobilize biomolecules onto thiol reactive surfaces in order to, e.g., make biosensors. The mechanism involves light-induced formation of free, reactive thiol groups in disulphide containing molecules. This technology allows for the creation of arrays of biomolecules with a high degree of reproducibility, circumventing the need for often expensive nano/micro-dispensing technologies. The ultimate size of the immobilized spots is defined by the focal area of the UV beam. Light-induced immobilization has the added benefit that the immobilized molecules will be spatially oriented and covalently bound to the surface. In this paper, we demonstrate the utility of a sensor array created with the new sensor technology when integrated into a microfluidic system. Protein arrays made using light-induced immobilization showed successful antigen/antibody binding in a flow cell allowing the visualisation of real time binding and enzyme activity. ...

Energy Technology Data Exchange (ETDEWEB)

Among the most promising technological alternatives for the development of photovoltaic modules and cells of a low cost, good energetic conversion and feasibility for mass production, polycrystalline silicon thin film solar cells deposited directly on a transparent substrate are currently being considered the best. We have developed in our laboratory a PECVD reactor capable of producing the deposition of amorphous hydrogenated silicon at rates of above 2 nm/seg, allowing a significant production per line on the plant. Discharge gas is silane, to which diborane or phosphine is added so as to form the cell. Basically, work is done on a structure of cell type TCO/n+/p-/p+/M, which has 2 {mu}m of total thickness. Schott AF-37 glass is used as a substrate, for their ability to withstand temperatures of up to 800 C. The amorphous cell is subsequently annealed at ...

Energy Technology Data Exchange (ETDEWEB)

ITN Energy Systems is developing next-generation solar cells based on the concepts of an optical rectenna. ITN's optical rectenna consists of two key elements: (1) an optical antenna to efficiently absorb the incident solar radiation, and (2) a high-frequency metal-insulator-metal (MIM) tunneling diode that rectifies the AC field across the antenna, providing DC power to an external load. The combination of a rectifying diode at the feedpoints of a receiving antenna is often referred to as a rectenna. Rectennas were originally proposed in the 1960s for power transmission by radio waves for remote powering of aircraft for surveillance or communications platforms. Conversion efficiencies greater than 85% have been demonstrated at radio frequencies (efficiency defined as DC power generated divided by RF power incident on the device). Later, concepts were proposed to extend the rectennas into the IR and optical region of the electromagnetic spectrum for use as ...

Energy Technology Data Exchange (ETDEWEB)

A preliminary design effort directed toward a low concentration ratio photovoltaic array system capable of delivering multihundred kilowatts (300 kW to 1000 kW range) in low earth orbit is described. The array system consists of two or more array modules each capable of delivering between 113 kW to 175 kW using silicon solar cells or gallium arsenide solar cells, respectively. The array module deployed area is 1320 square meters and consists of 4356 pyramidal concentrator elements. The module, when stowed in the Space Shuttle's payload bay, has a stowage volume of a cube with 3.24 meters on a side. The concentrator elements are sized for a geometric concentration ratio (GCR) of six with an aperture area of .25 sq. m. The structural analysis and design trades leading to the baseline design are discussed. It describes the configuration, as well as optical, thermal and electrical performance analyses that support the ...

International Nuclear Information System (INIS)

The properties of the ideal gas of classical (nonquantum) tachyons are considered. Starting from the definition of thermodynamic functions for this system, it may be found that tachyons and bradyons gases are similar. (AA).

Energy Technology Data Exchange (ETDEWEB)

United Solar completed its Phase 1 report and its proposal for Phase 2 of the PVBONUS Two program at the end of March 1998. At the same time, it also completed and submitted a proposal to the California Energy Commission PIER program for additional funding to cost-share development and testing of a pre-production model of the PVT-14. It was unsuccessful in both of these proposed efforts. While waiting for the proposal decisions, work continued in April and May to analyze the system design and component decisions described below. This document is a final summation report on the Phase 1 effort of the PVBONUS Two program that describes the key technical issues that United Solar and its subcontractor, Industrial Solar Technology Corporation, worked on in preparation of a Phase 2 award. The decisions described were ones that will guide the design and fabrication of a pre-production prototype of a 1500:1 mirrored concentrator with gallium arsenide cells when United solar ...

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately ...

International Nuclear Information System (INIS)

Recent advances in thin film solar photovoltaic converters (PV's) can furnish multimegawatt power levels during lunar daylight periods with only modest mass requirements. The extended duration of lunar night (ca. 354 hr) and the high specific mass of earth-imported energy storage systems (regenerative fuel cells, batteries, etc.) render PV plus import storage power systems non-competitive with nuclear power plants for lunar bases. However, power storage or generation methods which can be constructed using primarily lunar materials, used either alone or with lightweight PV's, can be attractive alternatives to nuclear power. Three separate generic systems which can provide favorable low import mass goals have been identified and studied. These are: gravitational energy generation using lunar soil, thermal energy storage using basalt rock or glass, and electrochemical storage using lunar derived electrodes or fuels. Design, structural and ...

Energy Technology Data Exchange (ETDEWEB)

This proceedings is the compilation of papers presented at the ninth PV Performance and Reliability Workshop held at the Sheraton Denver West Hotel on September 4--6, 1996. This years workshop included presentations from 25 speakers and had over 100 attendees. All of the presentations that were given are included in this proceedings. Topics of the papers included: defining service lifetime and developing models for PV module lifetime; examining and determining failure and degradation mechanisms in PV modules; combining IEEE/IEC/UL testing procedures; AC module performance and reliability testing; inverter reliability/qualification testing; standardization of utility interconnect requirements for PV systems; need activities to separate variables by testing individual components of PV systems (e.g. cells, modules, batteries, inverters,charge controllers) for individual reliability and then test them in actual system configurations; more results reported from field ...

International Nuclear Information System (INIS)

Background and purpose: A series of phase I/II clinical trials are being initiated in several UK centres to explore the use of dose-escalated schedules for the treatment of non-small cell lung cancer (NSCLC). Among them the IDEAL-CRT trial (ISRCTN12155469) will investigate the introduction of individualised 'isotoxic' treatment schedules based on the relative mean lung normalised total dose (rNTDmean), an estimator related to lung toxicity. Since treatment planning will be performed using different treatment planning systems (TPSs), for the quality assurance of the trial we have carried out work to quantify the influence of dose calculation algorithms based on the determination of rNTDmean and on the choice of individualised prescription doses. Material and methods: Twenty-five patient plans with stage I, II and III NSCLC were calculated, with the same prescription dose, using the Adaptive Convolve (AC) and Collapsed Cone (CC) algorithms of the ...

Energy Technology Data Exchange (ETDEWEB)

One of the most densely populated urban regions in the world is the Sao Paulo Metropolitan region (SPMR) in the State of Sao Paulo, Brazil. Air pollution is a real problem, mainly caused by vehicle exhaust fumes. The air pollution abatement measures adopted in the SPMR, such as the addition of ethanol to gasoline, the use of cars running on pure alcohol, the restrictions in the circulation of vehicles and the utilization of electronic fuel injection and catalyst have had a positive effect on the environment. The 25,000 buses and approximately 400,000 trucks, all operating on diesel, have not been affected by these measures, and it is believed that SPMR is the ideal location for testing new vehicular pollution reduction technologies. A project to this effect was launched by the Ministry of Mines and Energy in conjunction with a host of other partners, and it involved the operation of a fuel cell bus using hydrogen produced by electrolysis. The ...

Energy Technology Data Exchange (ETDEWEB)

IMRT with inverse planning allows simultaneous integrated boost strategies that exploit the heterogeneous dose distribution within the planning target volumes (PTVs). In this scenario, the location of cold spots within the target becomes a crucial issue and has to be related to the distribution of the clonogenic cell density (CCD). The main aim of this work is to provide the means to calculate the optimal prescription dose in a relative inhomogeneous dose distribution. To achieve this, the prescription dose has to be assigned to obtain the same tumor control probability (TCP) as the ideal homogeneous distribution, taking into account different CCDs in different PTVs (i.e. visible and subclinical regions). An adapted formulation of the linear-quadratic model, within the F-factor formalism, has been derived to preserve a chosen TCP value for the whole target volume. The F-factor has been investigated to show its potential applications in clinical ...

International Nuclear Information System (INIS)

This paper presents case studies of economic feasibility of solar photovoltaic systems using the software AVES-F (Analysis of Economic Feasibility of Photovoltaic Systems), developed by the authors, considering cases of stand-alone and grid-connected systems. The software takes into account several factors that can influence the economic feasibility of these kind of systems, like load to be supplied, distance to the grid, the use regime of the system, applied subsidies and others. The main goal of this paper is to analyze some of these factors and to observe how they can affect the economics of PV systems for electricity generation. (authors)

Energy Technology Data Exchange (ETDEWEB)

The ternary compound CuInS{sub 2} is attractive for solar cells due to its band gap of 1.54 eV which borders the optimum value necessary for conversion of a solar spectrum. Recently, works on thin film cells based on this material (ZnO/CuInS{sub 2}) has been reported to show efficiency as high as 11.4%. In this paper, the orientation and the morphology of CuInS{sub 2} sprayed films are determined by the means of X-ray diffraction and scanning electron microscopy. Sprayed CuInS{sub 2} films deposited onto a transparent Pyrex substrate with standard fabrication parameters show a chalcopyrite structure with a preferential orientation (1 1 2). A model based on the calculation of the relative dielectric function {epsilon} has been performed in order to obtain the profile of variation of this parameter and to understand the optical behavior of this material via its transmittance and reflectance in visible and near-infrared regions (0.35-2.5 {mu}m). ...

Energy Technology Data Exchange (ETDEWEB)

Successful interface engineering requires compositional and electronic material characterization as a prerequisite for understanding and intentionally generating interfaces in photovoltaic devices. The paper gives an overview with several examples, all referring to Cu(In,Ga)(S,Se){sub 2} ('CIGSSe')-based solar cells, with an emphasis on characterization using highly specialized methods, such as elastic recoil detection analysis, X-ray emission spectroscopy and photoelectron spectroscopy using synchrotron and ultraviolet light for excitation, inverse photoemission spectroscopy and Kelvin probe force microscopy. First, the determination of the depth profile of the band gap energy E{sub g} in the absorber layer is demonstrated. The modification of E{sub g} towards both interfaces is discussed in terms of beneficial electronic effects. Next, the interface between absorber and buffer layers with alternative and promising non-toxic ...

Energy Technology Data Exchange (ETDEWEB)

A set of nomographs to estimate the levelized energy cost for photovoltaic systems are presented. These are designed to assist system designers, analysts, and planners in estimating the effects of research and development and system-design optimization on the delivered cost of energy. The nomographs are based on a refined version of the energy cost estimation equation that appears in the National Photovoltaics Program Five-Year Research Plan. The nomographs have been prepared to emphasize technologies with the potential of producing low-cost energy (<$0.40/kWh levelized in nominal terms or $0.17/kWh in 1982 dollars), and thus primarily apply to far-term or advanced intermediate photovoltaic technologies. Separate sets of nomographs are presented to encompass both flat-plate and concentrator technologies. To supplement the nomographs, a set of tabular solutions of the energy cost equation are included as an appendix.

Science.gov (United States)

... s excellent water quality and ideal temperature conditions. Oyster aquaculture operations on the Damariscotta lease about 100 acres ... ...

Energy Technology Data Exchange (ETDEWEB)

Described herein are the results of the FY1994 research program for analysis and evaluation for thin film solar cells. The study on quantitative analysis of hydrogen atoms in a plasma determines quantity of hydrogen atoms in the plasma of monosilane diluted with hydrogen. It is found, contrary to expectation, that quantity of hydrogen atoms in the plasma decreases as it is more diluted with hydrogen. The study on light-induced degradation of the thin chlorine-base amorphous silicon films confirms that the plasma CVD method with 20% of dichlorosilane gas added to monosilane gas produces the thin amorphous silicon film 3 times faster than the conventional method. The thin film has essentially the same defect density as the one prepared by the conventional method, showing good photoelectric characteristics. The thin film of chlorinated amorphous silicon has a 1 digit lower defect density than the conventional one of amorphous silicon, as revealed by the accelerated ...

Energy Technology Data Exchange (ETDEWEB)

The intention of the research carried out was to develop photovoltaic driven solar heating systems applied for drying of medicinal plants in remote areas. Identification of hybrid photovoltaic - photothermal systems was done and discussion of technical features and applicability of such systems in agriculture is presented. Detail technical specification of PV powered medicinal plants solar dryer and cost effectiveness parameters are given. Operational and economic results obtained during testing of the dryer are promising. (orig.) 4 refs.

British Library Electronic Table of Contents (United Kingdom)

Diesel power technology has been utilized worldwide, especially in remote regions, because of its low initial capital cost. But it has negative effects on the surrounding environment and causes global warming. On the other hand, depleting oil and fuel resources has made it inevitable to seek alternative/renewable energy resources. In Iran, the cost of fuel is highly subsidized. If Iran removes the fuel subsidy, the cost of diesel fuel would increase and the photovoltaic (PV) or hybrid PV/diesel systems would become more attractive. Hybrid photovoltaic/diesel/battery (PV/diesel/bat) systems which use PV energy, combined with diesel generation power and battery bank storage are an excellent solution to decrease diesel generator costs, pollution, and electrification of remote rural areas. In ...

Energy Technology Data Exchange (ETDEWEB)

An important growth in the power of the photovoltaic systems connected to a grid has recently been observed. In spite of the advances in module technology, the problems in the system design increased, especially regarding the surface of the earth they occupy. In this work we propose a complete model for plant simulation with different wiring diagrams and under dynamic shading. Results obtained from simulations showed that the configuration with the lowest performance was that of only one serial-parallel group, whereas the highest efficiency corresponded to a design of groups of modules in parallel connected then in series. In general, a higher efficiency was obtained diminishing the quantity of modules in series and increasing their number in parallel. The simulation model proposed allows exploring different alternatives of wiring modules and finding the most efficient configurations for photovoltaic plants of medium and high power. (author)

Energy Technology Data Exchange (ETDEWEB)

This document is an executive summary of the colloquium organized by the French syndicate of renewable energies (SER) which took place at the Maison de l'UNESCO in Paris during the national debate on energies organized by the French government in spring 2003. The colloquium was organized around 6 round tables dealing with: the world perspectives and the environmental context of the contribution of renewable energies to the sustainable development (respect of Kyoto protocol commitments, contribution to the security of energy supplies, lack of large scale program of development of decentralized power generation in developing countries, lack of market tools linked with CO{sub 2} emissions, improvement of competitiveness); development of renewable energies in Europe (promotion and sustain in all European countries, obligation of supply and purchase, pricing regulation, European harmonization of practices); renewable electricity and its place in the new orientation law about ...

Energy Technology Data Exchange (ETDEWEB)

The abatement of CO{sub 2} emissions is a huge technical and economical challenge. Fossil fuels, which represent 88% of the world primary energy consumption, are the main source of the 25 billions of CO{sub 2} released each year in the atmosphere. The mastery of CO{sub 2} emissions cannot come from a single technology but must result from the simultaneous implementation of several means, like the development of carbon-free energies and the mastery of fossil fuel emissions. The opportunities of progress are numerous and compatible with the economic development. This document presents, first, the different greenhouse gases, the CO{sub 2} emissions per country and the main sources of CO{sub 2} emissions (power and heat generation, transports). Then it presents different ways of abatement of CO{sub 2} emissions: clean coal technologies, gas combined cycles, CO{sub 2} sequestration, reduction of fuel consumption in transports, development of carbon-free energies: wind power, solar ...

CERN Document Server

Computing with cells

British Library Electronic Table of Contents (United Kingdom)

We introduce a weak order ideal property that suffices for establishing the Evans-Griffith Syzygy Theorem. We study this weak order ideal property in settings that allow for comparison between homological algebra over a local ring R versus a hypersurface ring R =R/(x^n). Consequently we solve some relevant cases of the Evans-Griffith syzygy conjecture over local rings of unramified mixed characteristic p, with the case of syzygies of prime ideals of Cohen-Macaulay local rings of unramified mixed characteristic being noted. We reduce the remaining considerations to modules annihilated by p^s, s>0, that have finite projective dimension over a hypersurface ring.

Science.gov (United States)

... turbine blade heat-transfer and study the heat-transfer augmentation in idealized geometry and its ... responsible for heat transfer augmentation. ...

CERN Document Server

A process has been proposed to increase the efficiency of an ideal Otto cycle via a quantum heat engine that has no cooler reservoir. We show that such a process is not feasible.

Energy Technology Data Exchange (ETDEWEB)

The European demonstration project Hip Hip (house integrated photovoltaic high-tech in public) led the French photovoltaic market to reach a level comparable to those of the other European countries in terms of relevance of implemented solutions and costs. This document presents the best realizations and the experience gained through the Hip Hip project. Its aim is to convince the designers and managers of building projects of the advantages of photovoltaic installations integrated to the structure and connected to the power distribution grid: 1 - presentation of the technology; 2 - status of the Hip Hip demonstration project (goals, results: main innovations and impact on the French market); 3 - different possibilities of integration to the building structure; 4 - examples of projects realized in France in the framework of the Hip Hip project: integration in glass roof, frontage, added elements, fitting on roofs. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

Recently, organic semiconducting materials have gained a broad interest due to their potential for organic electronic devices such as organic light emitting diode (OLED), organic photovoltaic devices and organic field-effect transistors (OFETs). Optical properties of organic semiconducting materials are important for practical application. For example, the power conversion efficiency of organic photovoltaic devices is mainly affected by absorption properties of organic materials. Proton irradiation is one of the efficient methods to change the optical properties of organic materials. In this paper, we investigate the changes of optical properties of various polymers using the proton irradiation.

Science.gov (United States)

Basic research of the structure and electronic properties of a-Si:H is reported with particular emphasis on the role of defects. The main findings are as follows: (1) low defect density material can be deposited at a high rate using SiH/sub 4/ diluted in He or Ne. Using Ar or Kr results in a high defect density and columnar material; (2) an electrical bias during deposition modifies the band gap, hydrogen concentration and structure; (3) the clustering of hydrogen in the regions between the columns is confirmed; (4) hydrogen diffusion is observed by NMR; (5) the oxidation of an a-Si:H surface results in approx. 3 x 10/sup 11/ cm/sup -2/ dangling bonds at the interface; (6) auger recombination of photoexcited carriers is a significant non-radiative mechanism at low temperatures; (7) non-radiative recombination by diffusion and capture at dangling bonds is observed at temperatures above 50 to 100/sup 0/K; (8) the defect density in doped and compensated a-Si:H is determined by the ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive hydrogen cooling and adapted ...

Energy Technology Data Exchange (ETDEWEB)

As the U.S. Department of Energy's (DOE's) Solar Energy Technologies Program initiates new cost-shared solar energy R&D under the Solar America Initiative (SAI), it is useful to analyze the experience gained from cost-shared R&D projects that have been funded through the program to date. This report summarizes lessons learned from two DOE-sponsored photovoltaic (PV) projects: the Photovoltaic Manufacturing Technology/PV Manufacturing R&D (PVMaT/PVMR&D) project and the Thin-Film PV Partnership project. During the past 10-15 years, these two projects have invested roughly $330 million of government resources in cost-shared R&D and leveraged another $190 million in private-sector PV R&D investments. Following a description of key findings and brief descriptions of the PVMaT/PVMR&D and Thin-Film PV Partnership projects, this report presents lessons learned from the projects.

British Library Electronic Table of Contents (United Kingdom)

In areas where grid connection is difficult and costly, the use of renewable energy is both economically and environmentally advantageous. Due to typically low system efficiency (10%) and intermittency of photovoltaic (PV) electricity generation, a new design of multi-level H-bridge inverter technology is considered. This multi-level technology increases DC to AC conversion efficiency and the design includes battery energy storage to enable 24/7 operation. The proposed multi-level inverter is compared and contrasted with other existing designs. The proposed cascaded inverter provides lower switching losses, simple switching techniques, modularity, and simpler charge-balancing approaches than conventional technology. A switching technique was designed for the proposed multi-level inverter t...

Energy Technology Data Exchange (ETDEWEB)

The Measurements and Characterization Branch actively supports the advancement of DOE/NREL goals for the development and implementation of the solar photovoltaic (PV) technology. The primary focus of the laboratories is to provide state-of-the-art analytical capabilities for materials and device characterization and fabrication. The branch houses a comprehensive facility that Is capable of providing information on the full range of PV components. A major objective of the branch is to aggressively pursue collaborative research with other government laboratories, universities, and industrial firms for the advancement of Pv technologies. Members of the branch disseminate research findings to the technical community in publications and presentations. The Measurements and Characterization Branch encompasses seven coordinated research groups, providing integrated research and development that covers all aspects of photovoltaic materials/devices ...

Energy Technology Data Exchange (ETDEWEB)

A full analysis is shown in this paper for the cost of kWh generated from photovoltaic station located in Kuwait. By using a 21 years weather data for Kuwait, the yearly generated energy was found by proposing the PV station capacity with known panels tilt angle. The cost of kWh generated from PV station was compared with the kWh generated from conventional units in the country. A sensitivity analysis was done to some factors, capital cost per installed PV peak watt, discount rate, and operating peak hours, which affect the cost of kWh production from both PV and conventional units. If the PV station is proposed to be installed in Kuwait, the capital cost per PV installed peak watt must be less than today`s prices. (author)

UK PubMed Central (United Kingdom)

Peri-prosthetic infections are notoriously difficult to treat as the biomaterial implant is ideal for bacterial adhesion and biofilm formation, resulting in decreased antibiotic sensitivity....Full Text Available

UK PubMed Central (United Kingdom)

Chemoprevention, especially through the use of naturally occurring phytochemicals capable of impeding the process of carcinogenesis at one or more steps, is an ideal approach for cancer management....Full Text Available

UK PubMed Central (United Kingdom)

Chemoprevention strategies to prevent the development of lung cancer in at-risk individuals are a key component in disease management. In addition to being highly effective, an ideal chemopreventive...Full Text Available

UK PubMed Central (United Kingdom)

There has been a major interest in the drug treatment of osteoporosis and an increase in the number of drugs available in most countries. The ideal drug (one which increases or restores bone density...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundPrevious research has demonstrated that exposure to images depicting the thin female ideal has negative effects on some females' levels of body dissatisfaction. Much of...Full Text Available

UK PubMed Central (United Kingdom)

Several nematode species have now attained ‘model organism’ status, yet there remain many niches in basic biological inquiry for which nematodes would be ideal model systems of study....Full Text Available

International Nuclear Information System (INIS)

The formalism of statistical mechanics of particles slower than light has been considered from the point of view of the application of this formalism for the description of tachyons. Properties of ideal gases of tachyons have been discussed in detail. After finding general formulae for quantum, Bose and Fermi gases the classical limit has been considered. It has been shown that Bose-Einstein condensation occurs. The tachyon gas of bosons violates the third principle of thermodynamics. Degenerated Fermi gas has been considered and in this case the entropy vanishes at zero temperature. Difficulties of formulating covariant statistical mechanics have been discussed.

Energy Technology Data Exchange (ETDEWEB)

The formalism of statistical mechanics of particles slower than light has been considered from the point of view of the application of this formalism for the description of tachyons. Properties of ideal gases of tachyons have been discussed in detail. After finding general formulae for quantum, Bose and Fermi gases the classical limit has been considered. It has been shown that Bose-Einstein condensation occurs. The tachyon gas of bosons violates the third principle of thermodynamics. Degenerated Fermi gas has been considered and in this case the entropy vanishes at zero temperature. Difficulties of formulating covariant statistical mechanics have been discussed.

CERN Document Server

System identification is a necessity in control theory. Classical control theory usually considers processes with integer order transfer functions. Real processes are usually of fractional order as opposed to the ideal integral order models. A simple and elegant scheme is presented for approximation of such a real world fractional order process by an ideal integral order model. A population of integral order process models is generated and updated by PSO technique, the fitness function being the sum of squared deviations from the set of observations obtained from the actual fractional order process. Results show that the proposed scheme offers a high degree of accuracy.

International Nuclear Information System (INIS)

This 2001 edition of the guide to UK renewable companies and equipment and service providers presents summaries of the different industry sectors covering wind power, photovoltaics, solar water heating, geothermal heat pump, hydroelectric power, marine current and wave technology, bioenergy, power generation from landfill gas, energy from waste, and cogeneration. A UK company classification listing and index is provided along with listing of UK organisations and companies and an index of advertisers.

Energy Technology Data Exchange (ETDEWEB)

This paper discusses the characteristics and needed improvements/enhancements required for the expansion of the grid-tied residential power systems market. The purpose of the paper is to help establish a common understanding, between the technical community and the customers of the technology, of value and costs and what is required in the longer term for reaching the full potential of this application.

British Library Electronic Table of Contents (United Kingdom)

Abstract The term -stem cell- most commonly refers to embryonic stem cells, particularly in the lay media; however, it also describes other cell types. A stem cell represents a cell of multi-lineage potential with the ability for self-renewal. It is now clear that the plasticity and immortality of a given stem cell will depend on what type of stem cell it is, whether an embryonic stem cell, a fetal-placental stem cell or an adult stem cell. Stem cells offer great promise as cell-based therapies for the future. With evolving technology, much of the socio-political debate regarding stem cells can now be avoided.

DEFF Research Database (Denmark)

Udgivelsesdato: 2002-Mar

Science.gov (United States)

PMID:21290990

Energy Technology Data Exchange (ETDEWEB)

Application of an optimization technique to extract the non-ideal parameters of gas absorption with chemical reactions process was described. The gas absorption was modeled using mass transfer theory to represent the realistic behaviors of an absorber. The model was a highly non-linear iterative model which correlated the overall rate of absorption as the function of unknown non-ideal parameters, including the physical liquid mass transfer coefficient and the wetted interfacial area of of packings. The optimization program was developed to minimize the sum of squares of relative errors between the model predictions and the experimental data. Four sets of experimental data (case studies) with different operating conditions were used for extracting parameters. Comparisons between predicted and experimental measured overall absorption rate were in good agreement, average absolute value of relative errors not exceeding 5.4 %. 18 refs., 3 tabs., 4 ...

British Library Electronic Table of Contents (United Kingdom)

Ideal free distribution (IFD) models are perhaps the group of mathematical models of behavior that have been the most widely and successfully applied by empiricists. These models can be applied to nearly any situation in which consumers compete?by any mechanism?for resources that are patchily distributed in their environment. Although IFD models have come to be broadly accepted, experiments that simultaneously test more than a single prediction are rare. Instead, investigators normally either test (1) for a relationship between the distribution of consumers and the distribution of resources or (2) whether average fitnesses are equal across resource patches. We conducted experiments with pea aphids (Acyrthosiphon pisum Harris) feeding on two patches of fava beans (Vicia faba L.) to fully in...

International Nuclear Information System (INIS)

The Utility PhotoVoltaic Group (UPVG), supported by member dues and a grant from the US Department of Energy, has as its mission the acceleration of the use of cost-effective small-scale and emerging large-scale applications of photovoltaics for the benefit of electric utilities and their customers. Formed in October, 1992, with the support of the American Public Power Association, Edison Electric Institute, and the National Rural Electric Cooperative Association, the UPVG currently has 90 members from all sectors of the electric utility industry. The UPVG's efforts as conceived were divided into four phases: Phase 0--program plan; Phase 1--organization and strategy development; Phase 2--creating market assurance; and Phase 3--higher volume purchases. The Phase 0 effort developed the program plan and was completed early in 1993. The Phase 1 goal was to develop the necessary background information and analysis to lead to a decision as to which ...

Energy Technology Data Exchange (ETDEWEB)

This document gathers the presentations given at the first French national meetings of solar energy for the development of solar systems in buildings. The meeting was organized over two days. The first day comprises 4 workshops about: urbanism and planning, cultural acceptability of solar energy in buildings (the OPAC 38 housing association, point of view on an energy information point, the Freiburg (Germany) solar region and marketing examples), technical integration to the structure (Clipsol solutions), and economical criteria (compared impacts of R and D public photovoltaic programs (USA, Japan, Germany, France, Italy), financing of rehabilitation projects, global approach of solar photovoltaic energy, technical solutions and strategy of products development, why and how to make an economical analysis of solar energy applications in the building industry). The second day comprises a plenary session and a round table: global status of solar ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports the study results on the standard weather data necessary for simulation of PV power generation systems in fiscal 1994. In the study on the selection criterion of the standard weather data from the viewpoint of PV power generation systems, three typical years are used; a year with average solar radiation, and two years with extremely less and more solar radiation for safe simulation. The standard weather data are arranged for output calculation of PV power generation systems by selecting the most typical year based on long-term observation data. The data to be arranged are as follows; total, direct and scattered solar radiations incident upon a horizontal surface, solar radiation upon a slope surface, sunshine duration, air temperature, wind direction, wind velocity, amount of precipitation, and snow depth. For arrangement of the nationwide standard weather data, estimation of total solar radiation is necessary based on sunshine duration data observed by all weather ...

Energy Technology Data Exchange (ETDEWEB)

A free standing outdoor telephone booth is provided with a photovoltaic (PV) array, one or more rechargeable storage batteries and electrical control circuit which includes a temperature compensated control for limiting the supply of electrical energy from the PV array to the rechargeable battery to avoid over charging the battery, an ambient light (solar insolation) sensing circuit for controlling the electrical lamp load, to turn the lamp ON during dark ambient and OFF during light ambient conditions. In addition, the total discharge limit of the storage battery is controlled to a safe operating limit and a means is disclosed to power a fluorescent lamp at energy conserving intensities with energy derived from the rechargeable storage battery. The lamp control circuitry is preferably constituted by a high frequency power inverter with regulated output power to energize a low wattage fluorescent lamp and to dim the fluorescent lamp when the telephone is not in ...

International Nuclear Information System (INIS)

The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle-natural gas fired system. A photovoltaic system still uses comparatively expensive technology for electricity generation; even when external costs ...

International Nuclear Information System (INIS)

The article describes the energy in Lebanon. In 1995, 97% of the imported energy was based on hydrocarbons. Fuel and gas oil present 66% of the final energy. Air pollution is mainly caused by the transportation sector (vehicles and buses...) which presents 70% of the global atmospheric pollution. Renewable energy such as biomass, fossil energy, hydro-energy, solar energy... are also described. The solar energy was defined as a best solution that preserve health in Lebanon. The different applications of the solar for energy production is discussed: photovoltaic , thermal heating, sanitary hot water, electrical heaters, solar water heaters...In conclusion, solar heaters economize 80% of the annual energy expenses

International Nuclear Information System (INIS)

Atmospheric pressure plasma enhanced chemical vapour deposition system is built. The electrical and optical characteristics of the APPECVD system is given. The system is used to deposit conductive polymers and nano composites onto glass and metal surfaces. The morphological, optical, chemical and electrical characteristics of deposited surfaces are investigated using SEM, AFM four probe deposition purposes. The photovoltaic applications of plasma deposited polymers and nonconsumption are compared with deposited with electrochemical methods show different results. The electrical, chemical and morphological structures of the samples will be given.

Energy Technology Data Exchange (ETDEWEB)

Chlorophyll-a (Chl-a) assembled in hydrophobic domain by fatty acid with long alkyl hydrocarbon chain such as myristic acid (Myr), stearic acid (Ste) and cholic acid (Cho) modified onto nanocrystalline TiO{sub 2} electrode is prepared and the photovoltaic properties of the nanocrystalline TiO{sub 2} film by Chl-a are studied. Incident photon to current efficiency (IPCE) value at 660 nm in photocurrent action spectrum of Chl-a/Ste-TiO{sub 2}, Chl-a/Myr-TiO{sub 2} and Chl-a/Cho-TiO{sub 2} electrodes are 5.0%, 4.1% and 4.1%, respectively. Thus, the IPCE is maximum using Chl-a/Ste-TiO{sub 2} electrode. From the results of photocurrent responses with light intensity of 100 mW cm{sup -2} irradiation or monochromatic light with 660 nm, generated photocurrent increases using Chl-a/Ste-TiO{sub 2} electrode compared with the other Chl-a assembled TiO{sub 2} electrodes. These results show that the hydrophobic domain formed by stearic acid with long alkyl hydrocarbon chain is ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

CERN Document Server

Applied and fundamental aspects of plant cell, tissue, and organ culture

International Nuclear Information System (INIS)

Momentum- and speed-dependent Maxwell-Boltzmann equilibrium distributions have been derived for tachyons and compared with the corresponding relativistic distributions. This is followed by a calculation of the mean, most probable and r.m.s. speeds for both the relativistic and tachyonic distributions. The ideal gas of tachyons is discussed, including calculations of the internal energy and entropy. In each case a comparison is made with the corresponding bradyonic results. It is found that tachyons behave just like bradyons in the high-temperature limit, but have markedly different behaviour at low temperatures.

International Nuclear Information System (INIS)

It is maintained that special features of FFTF make it an ideal system to test sodium boiling detection techniques by acoustic/neutronic methods and to test the response of acoustic/neutronic sensors to vibrations. It is shown that accumulated research results indicate that such tests in FFTF are feasible, predictable, promising and safe. (author).

Wastenet

...Butley river and Ore estuary, Boyton Marshes attracts breeding wading birds in spring and ducks, geese and swans in winter. It's also ... During spring and autumn, it is an ideal place to see migrant wading birds, gulls and terns. Insh Marshes Insh ... Spring is also an excellent time to visit. Leighton Moss Leighton Moss is the largest reedbed in north-west England, and home ... When they leave in spring, wading birds take centre stage. Watch it all take place from our viewing centre and hide,...

Energy Technology Data Exchange (ETDEWEB)

In a reactor environment, the surface of a limiter or wall is primarily determined by the mechanism of erosion and deposition of surface material. It should be possible to use pellet injection to reduce net erosion to zero everywhere if low-Z materials are used for the surface. Erosion rates can, in general, be minimized by large area limiters and high plasma temperatures, which transmit power to the walls with less sputtering. Under ideal steady state conditions the wall surface is dominated by metallurgical effects in the wall.

Energy Technology Data Exchange (ETDEWEB)

Calibration-Free Laser-Induced Breakdown Spectroscopy (CF-LIBS) has been proposed several years ago as an approach for quantitative analysis of Laser-Induced Breakdown Spectroscopy spectra. Recently developed refinement of the spectral processing method is described in the present work. Accurate quantitative results have been demonstrated for several metallic alloys. However, the degree of accuracy that can be achieved with Calibration-Free Laser-Induced Breakdown Spectroscopy analysis of generic samples still needs to be thoroughly investigated. The authors have undertaken a systematic study of errors and biasing factors affecting the calculation in the Calibration-Free Laser-Induced Breakdown Spectroscopy spectra processing. These factors may be classified in three main groups: 1) experimental aberrations (intensity fluctuations and inaccuracy in the correction for spectral efficiency of a detection system), 2) inaccuracy in theoretical parameters used for calculations (Stark ...

UK PubMed Central (United Kingdom)

We studied telomeric DNA in leukemic cells as well as in normal T cells, B cells, monocytes, polymorphonuclear leukocytes, and bone marrow hematopoietic progenitor cells. No marked differences were...Full Text Available

Science.gov (United States)

... Solar Cell Radiation Respinnse Near the Interface o~f fliffprerv- ... 5 4. CALCUTl-ATED SOLAR CELL RLSPONSE FOR VARIOUS BASE MATERIALS ...

Energy Technology Data Exchange (ETDEWEB)

Experiments were designed to elucidate whether or not the irradiated bone marrow cells receive any stimulation for the self-replication and differentiation from normal 'stromal' cell colonies in the bone marrow cell culture in vitro. When irradiated or unirradiated bone marrow cells were overlaid on the normal adherent cell colonies, the proliferation of haemopoietic stem cells was supported, the degree of the stimulation depending on the starting cellular concentration. There was, however, no significant changes in the concentration of either CFUs or CFUc regardless of the dose of irradiation on the bone marrow cells overlaid. This was a great contrast to the dose-dependent decrease of CFUs or CFUc within the culture in which both the stem cells and stromal cells were ...

UK PubMed Central (United Kingdom)

In most adult tissues there reside pools of stem and progenitor cells inside specialized microenvironments referred to as niches. The niche protects the stem cells from inappropriate expansion...Full Text Available

Wastenet

... Fuel Cell Technologies Equipment on Environmental Expert Find and compare a variety of fuel cell technologies equipment on the world's largest environmental industry portal. View ...

UK PubMed Central (United Kingdom)

Purpose.There is a paucity of neuron replacement studies for retinal ganglion cells. Given the complex phenotype of these neurons, replacement of ganglion cells may be impossible....Full Text Available

UK PubMed Central (United Kingdom)

We report the isolation of adherent, clonogenic, fibroblast-like cells with osteogenic and adipogenic potential from the blood of four mammalian species. These cells phenotypically resemble but are...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Effects of cell concentrations on the survival and repopulation of haemopoietic stem cells after irradiation were studied in the long-term culture of mouse bone marrow cells in vitro. No difference was observed in the survival of the stem cells among cultures in which 0 - 10/sup 7/ cells were re-inoculated on the adherent cell colonies in the culture flask. Stem cells showed a significant proliferation within 1 week and the number of the stem cells exceeded the control in 3 weeks after irradiation in the cultures with less than 10/sup 6/ re-inoculated cells per flask. In contrast, there was a considerable delay in the onset of stem cell proliferation after irradiation in the culture with 10/sup 7/ cells per flask. Based on these results, a possibility that a ...

Energy Technology Data Exchange (ETDEWEB)

Beginning with an overview of renewable energy sources including biomass, hydroelectricity, geothermal, tidal, wind and solar power, this book explores the fundamentals of different renewable energy systems. The main focus is on technologies with high development potential such as solar thermal systems, photovoltaics and wind power. This text not only describes technological aspects, but also deals consciously with problems of the energy industry. In this way, the topics are treated in a holistic manner, bringing together maths, engineering, climate studies and economics, and enabling readers to gain a broad understanding of renewable energy technologies and their potential. The book also contains a free CD-ROM resource, which includes a variety of specialist simulation software and detailed figures from the book. (Author)

Energy Technology Data Exchange (ETDEWEB)

Simple frameworks have been developed for estimating the utilization potential of: (a) solar photovoltaic (SPV) pumps; (b) windmill pumps; (c) producer gas based dual fuel engine pumps; and (d) biogas based dual fuel engine pumps for irrigation water pumping in India. The approach takes into account factors such as: solar radiation intensity, wind speed, availability of bovine dung and agri-residues, and their alternative uses, ground water requirements for irrigation and its availability, affordability, and propensity of the users to invest in renewable energy devices, etc. SPV pumps are estimated to have the maximum utilization potential in India, followed by windmill pumps. (author)

International Nuclear Information System (INIS)

An attempt to develop a simple framework for financial evaluation of renewable energy technologies (RETs) such as photovoltaic (PV) pump, windmill pump, biogas and producer gas-driven dual fuel engine pumps for irrigation water pumping has been made. The unit cost of water and unit cost of useful energy delivered by the RETs have been estimated. The monetary benefits that accrued to the end-user have been quantified in terms of the amount of diesel or electricity saved. Financial figures of merit for the investments made in the RETs have been estimated. The effect of fuel price escalation on these measures of financial performance has also been evaluated along with the estimation of the break-even prices of fuels likely to be substituted by RETs. Results of some exemplifying calculations are presented and briefly discussed.

Energy Technology Data Exchange (ETDEWEB)

A 150 Watt thermophotovoltaic (TPV) power generator is being developed. The technical approach taken in the design focused on optimizing the integrated performance of the primary subsystems in order to yield high energy conversion efficiency and cost effectiveness. An important aspect of the approach is the use of a selective emitter radiating to a bandgap matched photovoltaic array to minimize thermal and optical recuperation requirements, as well as the non-recoverable heat losses. For the initial prototype system, fibrous ytterbia emitters radiating in a band centered at 980 nm are matched with high efficiency silicon photoconverters. The integrated system includes a dielectric stack filter for optical energy recovery and a ceramic recuperator for thermal energy recovery. The system has been operated with air preheat temperatures up to 1350K. The design of the system and development status are presented. {copyright} {ital 1997 American Institute of Physics.}

UK PubMed Central (United Kingdom)

SummaryIn vivo tumor cell migration through integrin-dependent pathways is key to the metastatic behavior of malignant cells. Using quantitative in vivo...Full Text Available

UK PubMed Central (United Kingdom)

For proper tissue morphogenesis, cell divisions and cell fate decisions must be tightly and coordinately regulated. One elegant way to accomplish this is to couple them with asymmetric cell divisions....Full Text Available

UK PubMed Central (United Kingdom)

We have established a cartilaginous fish cell line [Squalus acanthias embryo cell line (SAE)], a mesenchymal stem cell line derived from the embryo of an elasmobranch, the spiny dogfish...Full Text Available

UK PubMed Central (United Kingdom)

Interleukin 2 (IL-2) and B-cell growth factors I and II (BCGF I and BCGF II) are lymphokines produced by T cells that play a major role in T- and B-cell cooperation. Peripheral blood lymphocytes from...Full Text Available

UK PubMed Central (United Kingdom)

Normal cells, both in vivo and in vitro, become quiescent after serial cell proliferation. During this process, cells can develop immortality with genomic instability,...Full Text Available

UK PubMed Central (United Kingdom)

Endothelial cells and mural cells (smooth muscle cells, pericytes, or fibroblasts) are known to communicate with one another. Their interactions not only serve to support fully functional blood...Full Text Available

UK PubMed Central (United Kingdom)

Craniofacial injuries require a variety of different cell types to repopulate areas of bone, cartilage, tendon, and fat. Mesenchymal stem cells (MSCs) provide a multipotent cell source for tissue...Full Text Available

UK PubMed Central (United Kingdom)

Somatic cell nuclear transfer or therapeutic cloning has provided great hope for stem cell-based therapies. However therapeutic cloning has been experiencing both ethical and technical difficulties....Full Text Available

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

It has been postulated that thrombin binds to endothelial cells through, at least in part, cell surface glycosaminoglycans such as heparan sulfate, which could serve as antithrombin cofactor on the...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

In preimplantation mouse development, the first cell lineages to be established are the trophectoderm (TE) and inner cell mass. TE possesses epithelial features, including apical-basal cell polarity...Full Text Available

CERN Document Server

Several observational studies suggest that solar wind dynamic pressure fluctuations can drive magnetospheric ultra-low frequency (ULF) waves on the dayside. To investigate this causal relationship, we present results from Lyon-Fedder-Mobarry (LFM) global, three-dimensional magnetohydrodynamic (MHD) simulations of the solar wind-magnetosphere interaction. These simulations are driven with synthetic solar wind input conditions, where idealized ULF dynamic pressure fluctuations are embedded in the upstream solar wind. In three of the simulations, a monochromatic, sinusoidal ULF oscillation is introduced into the solar wind dynamic pressure time series. In the fourth simulation, a continuum of ULF fluctuations over the 0-50 mHz frequency band is introduced into the solar wind dynamic pressure time series. In this numerical experiment, the idealized solar wind input conditions allow us to study only the effect of a fluctuating solar wind dynamic ...

Energy Technology Data Exchange (ETDEWEB)

The influence of the velocity profile at the inlet boundary on the simulation of air velocity distribution inside an electrostatic precipitator is presented in this study. Measurements and simulations were performed in a duct and an electrostatic precipitator (ESP). A four-hole cobra probe was used for the measurement of velocity distribution. The flow simulation was performed by using the computational fluid dynamics (CFD) code FLUENT. Numerical calculations for the air flow were carried out by solving the Reynolds-averaged Navier-Stokes equations coupled with the realizable k-{epsilon} turbulence model equations. Simulations were performed with two different velocity profiles at the inlet boundary - one with a uniform (ideal) velocity profile and the other with a non-uniform (real) velocity profile to demonstrate the effect of velocity inlet boundary condition on the flow simulation results inside an ESP. The real velocity profile was obtained from the velocity ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the design of an on-board battery charger for an electric car. There are already various battery charger units on the market. However, these are not specifically designed for this application, and consequently do not provide an ideal solution. Because these products are not specific to one application, and instead opt to cover a variety of briefs, they are not ideal. They also tend to be heavier and more expensive than if the charger was built specifically for one purpose. The main design considerations were that the charger should be compact and lightweight. It was also specified that the design should be able to operate using either the single-phase or three-phase AC supply. Before the design process for the battery charger could commence, it was necessary for the author to get an appreciation of power electronics, since he had no previous experience in the subject. The author focused his attention on areas of the ...

Energy Technology Data Exchange (ETDEWEB)

Most of the organic electronic devices are nowadays fabricated under poor vacuum conditions. In this regard, there is only little knowledge about the impact of contamination of the metal electrode on the charge injection barrier in this kind of electronic devices. In our study we have performed X-ray and ultra violet photoemission spectroscopy (XPS, UPS) on interfaces between the organic semiconductor -sexithiophene and sputter cleaned (ideal) metals as well as contaminated (realistic) metals. As metal substrates we have used silver, gold, palladium, and platinum. These metals provide us a wide range of metal work functions from 4.2 eV for silver up to 5.5 eV for platinum. For all interfaces of -sexithiophene and contaminated metals we have observed a reduction of the interface dipole and the hole injection barrier. The charge injection barrier in all four cases is almost independent of the underlying metal (within an error of 0.2 eV) and the interface dipole ...

Science.gov (United States)

We have developed a cell-mediated mutagenesis assay in which cells with the appropriate markers for mutagenesis are co-cultivated with either lethally irradiated rodent embryonic cells that can metabolize carcinogenic hydrocarbons or with primary rat liver cells that can metabolize chemicals carcinogenic to the liver. During co-cultivation, the reactive metabolites of the procarcinogen appear to be transmitted to the mutable cells and induce mutations in them. Assays of this type make it possible to demonstrate a relationship between carcinogenic potency of the chemicals and their ability to induce mutations in mammalian cells. In addition, by simultaneously comparing the frequencies of transformation and mutation induced in normal diploid hamster cells by benzo(a)pyrene (BP) and one of its metabolites, it is possible to estimate the genetic ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The article describes the Solair 1 solar cell-powered aircraft. Measures to reduce the weight of the craft are cited.

International Science & Technology Center (ISTC)

Studies of the Superheavy-metal Effect as a Stress-factor on Protein Biosynthesis and Cytoskeleton Integrity in Animal Cells

Energy Technology Data Exchange (ETDEWEB)

Wet limestone scrubbing is once again becoming a popular technology for removal of sulfur dioxide (SO{sub 2}) from power plant emissions. Critical to the operation of wet limestone flue gas desulfurization (FGD) systems is accurate chemical analysis of scrubber solids. The analytical technique of thermogravimetry is ideal for this application, as the instrument can give precise readings of the principal scrubber solids components, calcium sulfite/sulfate hemihydrate, calcium sulfate dihydrate (gypsum), and unused calcium carbonate. The data provides plant chemists, engineers, and operators with information needed to fine-tune scrubber operation and detect process upsets. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Developing a modern electric power sector is necessary for economic growth and development to proceed. Institutions to implement an IRP (integrated resource planning) process do not exist in many countries. Hainan`s economy is growing rapidly with a concomitant increase in electricity demand. This is an ideal time in Hainan`s development to implement an IRP process. The challenge is for Hainan to develop institutions and incentive mechanisms for HEPCO (Hainan Electric Power Co.) to adopt cost-based pricing, run DSM programs, construct renewable generating plants, etc. One proposal is to great a Hainan government-wide IRP committee.

British Library Electronic Table of Contents (United Kingdom)

The paper takes as its starting point the diffusion of ICT applications associated with so-called 'customer relationship management' (CRM). CRM encourages organisations to shift their understanding of customers from an episodic and transaction-based perspective to one that emphasises continuous 'relationship management'. CRM applications thus promise to deliver more, real-time accurate information about consumer habits and behaviours therefore allowing organisations to maximise their extraction of business value. This paper explores the ways in which such inscriptive technologies are not merely referential but also constitutive of contemporary re-presentations and ideals of the consuming subject. Focusing on what we might call the 'digital doubles' of customer relationship management the a...

Energy Technology Data Exchange (ETDEWEB)

A high pressure waterjet has been used to study the surface roughening of superalloys as preparation for thermal spraying. Designed experiments for Mar-M 509 and Rene 80 were carried out for the effects of jet pressure and mass of water delivered per unit area. Comparisons were made of several superalloys in terms of erosion, surface roughness and topology. The mechanism of jet erosion of Rene 80 was studied in relation to its metallurgical microstructure. An MCrAlY coating by shrouded plasma spray was made over a waterjet prepared surface with excellent bonding and having an ideally clean interface.

Science.gov (United States)

A discussion of some of the difficulties with previous analyses of the resistivity of A-15 compounds is given. Precise high-temperature data on ..cap alpha..-particle- and electron-damaged Nb/sub 3/Ge and Nb/sub 3/Sn samples with different defect concentrations are presented here and analyzed in a simple way with use of a phenomenological model based on the idea that the ideal resistivity must approach some limiting value in the regime where the mean free path becomes comparable to the interatomic spacing.

Energy Technology Data Exchange (ETDEWEB)

Trapped ions are a near ideal system to study quantum information processing due to the high degree of control over the ion's external confinement and internal degrees of freedom. We demonstrate the key steps necessary for trapped ion quantum computing and focus on phonon-mediated entangling gates. We highlight several key algorithms implemented over the last decade with these gates and give a detailed description of Grover's quantum database search implemented with two trapped ion qubits.

International Nuclear Information System (INIS)

A thermodynamic model was used to estimate enthalpy of solution of carbon dioxide (CO_2) in methyldiethanolamine (MDEA) aqueous solutions. The model was based on a set of equations for chemical equilibria, phase equilibria, charge, and mass balances. Non-ideality in the liquid phase was taken into account by interaction parameters fitted to (vapor + liquid) equilibrium data. The enthalpies of solution of CO_2 were derived from the model using classical thermodynamic relations and were compared to experimental values obtained in previous works.

Energy Technology Data Exchange (ETDEWEB)

This article gives a survey of the history, properties and applications of 'Kevlar' aramide fibers. For example, the 'Kevlar' para-aramide fiber is used in compound materials in ship-, aircraft- and vehicle construction. 'Kevlar' is used as a replacement for asbestos, for example in brakes, clutches and seals or as rubber reinforcement (tyres, conveyor belts, hoses). The aramide fibers also offer manufacturers of ropes, hawsers and cables a near ideal range of properties. (MM).

British Library Electronic Table of Contents (United Kingdom)

Ascochyta blight causes significant yield loss in pulse crops worldwide. Integrated disease management is essential to take advantage of cultivars with partial resistance to this disease. The most effective practices, established by decades of research, use a combination of disease-free seed, destruction or avoidance of inoculum sources, manipulation of sowing dates, seed and foliar fungicides, and cultivars with improved resistance. An understanding of the pathosystems and the inter-relationship between host, pathogen and the environment is essential to be able to make correct decisions for disease control without compromising the agronomic or economic ideal. For individual pathosystems, some components of the integrated management principles may need to be given greater consideration tha...

Energy Technology Data Exchange (ETDEWEB)

The design of High-Voltage, Direct-Current transmission cables insulated with oil-impregnated cellulose paper is constrained by the maximum temperature and the maximum steady-state and transient stresses (voltage gradients) that the cable insulation can reliably withstand over the desired operating lifetime. Because the electrical stresses in the insulation are related in a very complex fashion to temperature, applied voltage and cable geometry, iterative techniques are required to compute the values of these stresses. Digital computers are ideally suited for these iterative techniques. This paper presents the principal equations and logic needed to develop suitable computer programs.

Energy Technology Data Exchange (ETDEWEB)

In an ideal system the surface of the dish is perfectly parabolic (no contour flaws are present), and the sun rays fall on the dish surface parallel to the focal axis (no sun tracking flaws are present). These two conditions are not realizable in practice; in this case, the parabolic dish system is called real system. In this paper a procedure for analysing the flux distribution on the receiver internal surfaces is presented for a cavity receiver with a real parabolic dish collector. First, the theoretical principles are discussed. Then the effect of the inaccuracy in the collector and in the sun tracking on the insolation pattern is described using an example.

Energy Technology Data Exchange (ETDEWEB)

The development of detailed chemical kinetic reaction mechanisms for analysis of autoignition and knocking of hydrocarbon fuels is described. In particular, kinetic processes of concern for the oxidation of complex hydrocarbon fuel molecules are emphasized. The wide ranges of temperature and pressure which are encountered by end gases in automobile engine combustion chambers result in extreme demands on reaction mechanisms which are intended to describe knocking conditions and predict rates of combustion and ignition. The reactions and chemical species which are most important in each temperature and pressure regime are discussed, and the validation of these reaction mechanisms through comparison with idealized experimental results is described. 53 refs., 8 figs., 5 tabs.

Energy Technology Data Exchange (ETDEWEB)

The linear integral equation based computer code (RON: Roger Oleg Nikolai), which was recently developed at Argonne National Laboratory, was used to calculate the self-amplified spontaneous emission (SASE) performance of the free-electron laser (FEL) being built at Argonne. Signal growth calculations under different conditions are used for estimating tolerances of actual design parameters. The radiation characteristics are discussed, and calculations using an ideal undulator magnetic field and a real measured magnetic field will be compared and discussed.

Science.gov (United States)

A hyperbolic Stefan problem based on the linearized Gurtin-Pipkin heat conduction law is considered. The temperature and free boundary are controlled by a thermostat acting on the boundary. This feedback control is based on temperature measurements performed by real thermal sensors located within the domain containing the two-phase system and/or at its boundary. Three different types of thermostats are analyzed: simple switch, relay switch, and a Preisach hysteresis operator. The resulting models lead to integrodifferential hyperbolic Stefan problems with nonlinear and nonlocal boundary conditions. Existence results are proved in all the cases. Uniqueness is also shown, except in the situation corresponding to the ideal switch.

Energy Technology Data Exchange (ETDEWEB)

This work reviews the differences in fuel economy between two direct injection diesel engine versions through the use of a First Law energy balance and a Second Law availability balance. Both experimental data and simulated results are used in the analysis. The use of an engine simulation allowed the important processes in each engine to be analyzed and a Second Law effectiveness calculated. The availability balances and effectiveness values are used to determine the effect of major engine components on the fuel economy. A comparison is also made with an ideal engine with selected perfect or reversible processes.

Energy Technology Data Exchange (ETDEWEB)

Volumetric properties of liquid mixtures of neon and hydrogen have been calculated using path integral hybrid Monte Carlo simulations. Realistic potentials have been used for the three interactions involved. Molar volumes and excess volumes of these mixtures have been evaluated for various compositions at 29 and 31.14 K, and 30 atm. Significant quantum effects are observed in molar volumes. Quantum simulations agree well with experimental molar volumes. Calculated excess volumes agree qualitatively with experimental values. However, contrary to the existing understanding that large positive deviations from ideal mixtures are caused due to quantum effects in Ne{endash}H{sub 2} mixtures, both classical as well as quantum simulations predict the large positive deviations from ideal mixtures. Further investigations using two other Ne{endash}H{sub 2} potentials of Lennard{endash}Jones (LJ) type show that excess volumes are very sensitive to the ...

Energy Technology Data Exchange (ETDEWEB)

A common practice of electric utilities experiencing transmission and distribution (T and D) system overloads is to expand the substation, add lines, or upgrade equipment, all of which are capital intensive options. In 1988, it was hypothesized that strategically sited photovoltaics (PV) could benefit parts of T and D systems near or at overloaded conditions. An evaluation methodology was developed and applied to a test case (Kerman Substation near Fresno, California). Analytical results suggested that the value of PV to the T and D system could substantially exceed its energy and generation capacity value. The importance of this finding indicated the need for empirical validation. This led to the construction of a 0.5 MW PV demonstration plant by Pacific Gas and Electric Company (PG and E) at Kerman, California as part of the PVUSA (PV for Utility Scale Applications) project. PVUSA is a national public-private partnership that is assessing and demonstrating the ...

International Nuclear Information System (INIS)

Growing of PV for electricity generation is one of the highest in the field of the renewable energies and this tendency is expected to continue in the next years. Due to the various seasonal, hourly and daily changes in climate, it is relatively difficult to find a suitable analytic model for predicting the performance of a grid-connected photovoltaic (GCPV) plant. In this paper, an artificial neural network is used for modelling and predicting the power produced by a 20 kWp GCPV plant installed on the roof top of the municipality of Trieste (latitude 45 deg. 40'N, longitude 13 deg. 46'E), Italy. An experimental database of climate (irradiance and air temperature) and electrical (power delivered to the grid) data from January 29th to May 25th 2009 has been used. Two ANN models have been developed and implemented on experimental climate and electrical data. The first one is a multivariate model based on the solar irradiance and the air temperature, while the second ...

Energy Technology Data Exchange (ETDEWEB)

The research for the development of flexible organic electronic devices (FEDs) is rapidly increasing worldwide, since FEDs will change radically several aspects of everyday life. Although there has been considerable progress in the area of flexible inorganic devices (a-Si or solution processed Si), there are numerous advances in the organic (semiconducting, conducting and insulating), inorganic and hybrid (organic-inorganic) materials that exhibit customized properties and stability, and in the synthesis and preparation methods, which are characterized by a significant amount of multidisciplinary efforts. Furthermore, the development and encapsulation of organic electronic devices onto flexible polymeric substrates by large-scale and low-cost roll-to-roll production processes will allow their market implementation in numerous application areas, including displays, lighting, photovoltaics, radio-frequency identification circuitry and chemical sensors, as well as to ...

DEFF Research Database (Denmark)

In order to identify cells of maternal origin in CVS cultures, tissue from 1st trimester abortions were cultivated and the cultures stained in situ for X-chromatin. Convoluted cells and maternal fibroblasts were found to be positive. By chromosome analysis of cultures from 105 diagnostic placenta biopsies, obtained by the transabdominal route, metaphases of maternal origin were found in nine cases. In eight of these cases colonies of convoluted cells were observed. We conclude that convoluted cells are of maternal origin and are a reliable marker for maternal cell contamination in CVS cultures.

International Nuclear Information System (INIS)

Understanding prostate stem cells may provide insight into the origin of prostate cancer. Primary cells have been cultured from human prostate tissue but they usually survive only 15-20 population doublings before undergoing senescence. We report here that RC-170N/h/clone 7 cells, a clonal cell line from hTERT-immortalized primary non-malignant tissue-derived human prostate epithelial cell line (RC170N/h), retain multipotent stem cell properties. The RC-170N/h/clone 7 cells expressed a human embryonic stem cell marker, Oct-4, and potential prostate epithelial stem cell markers, CD133, integrin #alpha#2#beta#1"h"i and CD44. The RC-170N/h/clone 7 cells proliferated in KGM and Dulbecco's Modified Eagle Medium with 10% fetal bovine serum and 5 #mu#g/ml insulin (DMEM + 10% FBS + Ins.) ...

British Library Electronic Table of Contents (United Kingdom)

Introduction: Haploidentical transplantation, with extensive T cell depletion to prevent GvHD, is associated with a high incidence of infection-related deaths. The key challenge is to improve immune recovery with allogeneic donor T cells without triggering GvHD. As T regulatory cells (Tregs) controlled GvHD in pre-clinical studies, the present study evaluated the impact of an infusion of donor CD4/CD25 + Tregs, followed by an inoculum of donor mature T cells (Tcons) and positively immunoselected CD34 + cells in the setting of haploidentical stem cell transplantation. Patients and methods: Twenty-eight patients were enrolled in this study (22 AML; 5 ALL; 1 NHL). All received immunoselected Tregs (CliniMACS, Miltenyi Biotec) followed by positively immunoselected CD34 + cells together with Tc...

Energy Technology Data Exchange (ETDEWEB)

The article is the second part of a review dealing with latest developments in the area of solar cell technologies and application. Physical principles, design and efficiency as well as advantages and disadvantages of GaAs- and CdS-solar cells are described. Power generation solar cell systems with voltage converters, combined solar cell/solar collector systems and thermoelectric solar systems are presented in the second part of the article.

UK PubMed Central (United Kingdom)

Cell therapy is a promising novel option for treatment of cardiovascular disease. Because the role of bone marrow-derived circulating progenitor cells (BM-CPCs) after cell therapy is less clear, we...Full Text Available

UK PubMed Central (United Kingdom)

Although human T-cell lymphotropic virus type I (HTLV-I) is the etiologic agent of adult T-cell leukemia/lymphoma (ATL), the role of viral gene expression in the progression to and maintenance of the...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Solid Oxide Fuel Cell (SOFC) is expected as a new power generation source. The development of SOFC is being conducted by CRIEPI, and so far several reports of the reults were presented. This report examines materials of SOFC. For the purpose, cells were made using some of typical materials and manufacturing processes, and cell performance tests were carried out.

UK PubMed Central (United Kingdom)

The penetration by moxifloxacin of human neutrophils (polymorphonuclear leukocytes [PMN]) and tissue-cultured epithelial cells (McCoy cells) was evaluated by a fluorometric assay. At...Full Text Available

UK PubMed Central (United Kingdom)

SUMMARYThe cytolytic activity of natural killer (NK) cells is regulated by inhibitory receptors that detect the absence of self molecules on target cells. Structural studies of...Full Text Available

Science.gov (United States)

Embryonic stem cells have the ability to develop into virtually any cell in the body, and may have the potential to treat medical conditions such as diabetes and Parkinsons disease. On August 9, 2001, President Bush announced that for the first time feder...

UK PubMed Central (United Kingdom)

BackgroundSpindle cell carcinoma (SpCC) is a rare microscopic type of cancer of the mouth and oropharynx. Although SpCC is thought to arise from squamous cell carcinoma (SCC), it...Full Text Available

Science.gov (United States)

... from Dr. Austin Smith of the Institute for Stem Cell Research, University of Edinburgh) was modified from the CGR8 ... to thank Dr. Austin Smith, the Institute for Stem Cell Research, University of Edinbu...

Science.gov (United States)

... Results of Source Emissions Testing UTC Fuel Cell Model PC25C ... Results of Source Emissions Testing: UTC Fuel Cell Model PC25C ...

UK PubMed Central (United Kingdom)

Target of rapamycin (TOR) kinases control cell growth through two functionally distinct multiprotein complexes. TOR complex 1 (TORC1) controls temporal cell growth and is sensitive to rapamycin, whereas...Full Text Available

UK PubMed Central (United Kingdom)

The cells of the endosperm of castor bean seeds (Ricinus communis) undergo programmed cell death during germination, after their oil and protein reserves have been mobilized. Nuclear...Full Text Available

UK PubMed Central (United Kingdom)

The rate and capacity for chloroform (CF) and trichloroethylene (TCE) transformation by a mixed methanotrophic culture of resting cells (no exogenous energy source) and formate-fed cells were measured....Full Text Available

UK PubMed Central (United Kingdom)

PURPOSE: To determine the frequency of ophthalmic abnormalities in patients with cutaneous T-cell lymphoma (mycosis fungoides and Sézary syndrome) and T-cell lymphoma involving the skin and...Full Text Available

UK PubMed Central (United Kingdom)

The primary aim of this study was to develop a model system that uses epidermal cells (keratinocytes and accessory pigmented cells) cultured on a reconstituted basement membrane biomatrix for use in...Full Text Available

UK PubMed Central (United Kingdom)

Special red cells were found on the adaxial surface of tertiary pulvini of Mimosa pudica and experiments performed to determine the origin and function of these cells. Using anatomical...Full Text Available

UK PubMed Central (United Kingdom)

Adhesion of Spirogyra (tentatively, Spirogyra fluviatilis) cells to glass is described. The cells of an algal filament can adhere to a substrate only when they are...Full Text Available

UK PubMed Central (United Kingdom)

Understanding the interactions between herpesviruses and their host cells and also the interactions between neoplastically transformed cells and the host immune system is fundamental to understanding...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundStem cells divide to reproduce themselves and produce differentiated progeny. A fundamental problem in human biology has been the inability to measure how often stem cells...Full Text Available

UK PubMed Central (United Kingdom)

Although most self-reactive T cells are eliminated in the thymus, mechanisms to inactivate or control T cells specific for extrathymic antigens are required and exist in the periphery. By investigating...Full Text Available

UK PubMed Central (United Kingdom)

One of the major decisions that germ cells make during their development is whether to differentiate into oocytes or sperm. In mice, the germ cells’ decision to develop as male or female depends...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

It Peripheral blood progenitor enriched CD34+ cells (PBPC) are rather often used as stem cell background in cancer patients following high dose therapy. Keeping in mind that precursor dendritic cells (DCs) originate from haematopoietic progenitor cells, purified CD34+ cells might also serve as starting cells for ex-vivo production of DC. The aim of the present study is to develop a clinical grade procedure for ex-vivo production of DC derived from enriched CD34+ cells. Various concentrations of CD34+ cells were grown in gas-permeable Teflon bags with different serum-free and serum-containing media supplemented with GM-CSF, IL-4, TNF-a, SCF, Flt-3L and INF-a. Serum-free CellGroSCGM medium for 7 days followed by CellGroDC medium in 7 days gave equal results as serum-containing ...

UK PubMed Central (United Kingdom)

The first cell lineage specification in mouse embryo development is the formation of trophectoderm (TE) and inner cell mass (ICM) of the blastocyst. This article is to review and discuss the...Full Text Available

UK PubMed Central (United Kingdom)

Naturally occurring and contaminant ferromagnetic and ferrimagnetic particles have been found within or near cells, and might allow pulsed magnetic fields to create transient cell membrane opening ("pores")....Full Text Available

Science.gov (United States)

... ions. MATERIALS AND METHODS Cell Culture Culture of NT2/D1 cells was carried out as described previously (18, 19). NT2 cells were plated at a density of 2. ... ...

UK PubMed Central (United Kingdom)

1. Paired or single recordings of paraventricular and/or supraoptic oxytocin cells at the beginning of suckling in urethane-anaesthetized rats enabled us to study cell recruitment and compare the characteristics...Full Text Available

UK PubMed Central (United Kingdom)

Cells have an internal compass that enables them to move along shallow chemical gradients. As amoeboid cells migrate, signaling events such as Ras and PI3K activation occur spontaneously on pseudopodia....Full Text Available

UK PubMed Central (United Kingdom)

Species differences in lifespan have been attributed to cellular survival during various stressors, designated here as ‘cell resilience’. In primary fibroblast cultures, cell...Full Text Available

UK PubMed Central (United Kingdom)

We review the application of C. elegans as a model system to understand key aspects of stem cell biology. The only bona fide stem cells in C. elegans...Full Text Available

UK PubMed Central (United Kingdom)

SummaryFor mammalian somatic cells the importance of microtubule cytoskeleton integrity in interphase cell cycle progression is uncertain. The loss, diminishment, or stabilization...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundA fundamental requirement for the exploitation of embryonic stem (ES) cells in regenerative medicine is the ability to reproducibly derive sufficient numbers of cells of...Full Text Available

UK PubMed Central (United Kingdom)

ObjectiveThe goal of the study was to investigate the genetic and molecular basis of a novel syndrome of marked hyperglucagonemia and pancreatic α cell hyperplasia...Full Text Available