By contrast to the large mass, complexity and recirculating power of conventional drivers for inertial confinement fusion (ICF), antiproton annihilation offers a specific energy of 90MJ/{micro}g and thus a unique form of energy packaging and delivery. In principle, antiproton drivers could provide a profound reduction in system mass for advanced space propulsion by ICF. We examine the physics underlying the use of antiprotons ({bar p}) to drive various classes of high-yield ICFtargets by the methods of volumetric ignition, hotspot ignition and fast ignition. The useable fraction of annihilation deposition energy is determined for both {bar p}-driven ablative compression and {bar p}-driven fast ignition, in association with 0-D and 1-D target burn models. Thereby, we deduce scaling laws for the number of injected antiprotons required per capsule, together with timing and focal spot requirements. The kinetic energy of the ...
X-ray ablation of material from the first wall and other components of an ICF (Inertial Confinement Fusion) chamber is a major threat to the laser final optics. Material condensing on these optics after a shot may cause damage with subsequent laser shots. To ensure the successful operation of the ICF facility, removal rates must be predicted accurately. The goal for this dissertation is to develop an experimentally validated x-ray response model, with particular application to the National Ignition Facility (NIF). Accurate knowledge of the x-ray and debris emissions from ICFtargets is a critical first step in the process of predicting the performance of the target chamber system. A number of 1-D numerical simulations of NIF targets have been run to characterize target output in terms of energy, angular distribution, spectrum, and pulse shape. Scaling of output characteristics with variations of both target yield and hohlraum wall thickness are ...
IntroductionTerror attacks in Southeast Asia were almost nonexistent until the 2002 Bali bomb blast, considered the deadliest attack in Indonesian history. Further attacks in 2003...Full Text Available
The effects of compression ratio on the history of the fuel-burning process was investigated in a single-cylinder direct-injection diesel engine. Two compression ratios of 21.4 and 18.5 were studied by using two wide and shallow bowls. The engine was operated at different speeds and overall air-fuel ratios, but with constant start-of-combustion timing at top dead center. The measured cylinder pressure was used to derive fuel-burning rate. At all conditions, the low-compression-ratio bowl had a larger mass of premixed-burned fuel and a higher peak specific fuel-burning rate. The fuel-burning rate in the diffusion-controlled phase of combustion decreased with decreasing compression ratio. The resulting combustion duration became longer at reduced compression ratio, and the difference could be as large as 14 crank-angle degrees. For the engine conditions examined ...
Russian field surgery with its long history and distinctive characteristics has accumulated great experience in the long-time practice of warfare. Chinese field surgery was established and developed on the basis of studying from the Russian model, which opened up new areas of traffic medicine, molecular traumatology and assessment of biological effects on weapon destruction and carried out in-depth research on wound ballistics, blast injury, burns and combined injury etc. through decades of construction with continuous development and innovation, and a series of major achievements have been made in these fields. By making comparative study on the historical evolution, structure system, characteristics of campaigns and development of society between Chinese and Russian field surgery, it can be found that there are great gaps between them and we should strengthen the research for more rapid development. PMID:20510098
The study of extragalactic planetary nebulae (EPN) is a rapidly expanding field. The advent of powerful new instrumentation such as the PN spectrograph has led to an avalanche of new EPN discoveries both within and between galaxies. We now have thousands of EPN detections in a heterogeneous selection of nearby galaxies and their local environments, dwarfing the combined galactic detection efforts of the last century. Key scientific motivations driving this rapid growth in EPN research and discovery have been the use of the PNLF as a standard candle, as dynamical tracers of their host galaxies and dark matter and as probes of Galactic evolution. This is coupled with the basic utility of PN as laboratories of nebula physics and the consequent comparison with theory where population differences, abundance variations and star formation history within and between stellar systems informs both stellar and galactic evolution. Here we pose some of the ...
Sep 28, 2011... to assess the application of high resolution imagery for burn severity mapping and to compare it to standard burn severity mapping methods. ...
In this review we attempt to reconstruct the evolutionary history of hominin life history from extant and fossil evidence. We utilize demographic life history theory and distinguish life history variables,...Full Text Available
The factors influencing premixed burning and the importance of premixed burning on the exhaust emissions from a small high-speed direct-injection diesel engine were investigated. The characteristics of premixed and diffusion burning were examined using a single-zone heat-release analysis. The mass of fuel burned in premixed combustion was found to be linearly related to the product of engine speed and ignition-delay time and to be essentially independent of the total amount of fuel injected. Accordingly, the premixed-burned fraction increased with increasing engine speed, with decreasing fuel-air ratio and with retarding injection timing. The hydrocarbon emissions did not correlate well with the premixed-burned fraction. In contrast, the oxides of nitrogen emissions were found to increase with decreasing premixed-burned fraction, indicating ...
Remote sensing is the most practical method available to managers of fire-prone forests for quantifying and mapping fire impacts. Differenced Normalised Burn Ratio (?NBR) is among the most widely used spectral indices for the mapping of burn severity but is difficult to interpret in terms of fire-related changes in key biophysical attributes and processes. We propose to quantify burn severity as a change in the leaf area index (?LAI) of a stand. LAI is a key biophysical attribute of forests, and is central to understanding their water and carbon cycles. Previous studies have suggested that changes in canopy LAI may be a major contributor to ?NBR and to the composite burn index (CBI) that is frequently used in combination with the NBR to assess burn severity on the ground. We applied remote...
Thinning and burning forests established on revegetated mine pits in jarrah (Eucalyptus marginata) forests of south-west Australia is being considered as a management option to accelerate succession in sites with excessive tree densities. To assess the impact of thinning and burning on reptiles and small mammals, we installed trapping grids in eight thinned and burned sites, each paired with untreated controls. Of the eight pairs, four were in rehabilitated sites (planted with nonlocal species) and four were in restored sites (seeded with local species). Thinning and burning had no significant impact on the small mammal community, although Cercatetus concinnus was more abundant in rehabilitated sites. In contrast, thinning and burning significantly increased reptile abundance and species r...
In this study the technical and economical possibilities of burning carbon monoxide (CO) of the flue gas and utilizing of the released heat in hot air cupola furnace used for melting have been studied. As basis for examining was burning of cleaned furnace...
We have constructed models for the vertical structure of disks around a black hole of 10/sup 6/ M/sub sun/ at distances from it smaller than the tidal breakup radius. These disks are massive enough that nuclear burning occurs in their central layers.
Aim:The effect of Tualang honey on wound healing in bacterial contaminated full-thickness burn wounds was evaluated in 36 male Sprague Dawley rats.Materials...Full Text Available
A 13 year- old girl presented to the department with sternomental contractures as a result of facial burns from kerosene explosion. Difficult airway was envisaged. Over the period of time she developed...Full Text Available
Although the roots of Ras sprouted from the rich history of retrovirus research, it was the discovery of mutationally activated RAS genes in human cancer in 1982 that stimulated an...Full Text Available
Following a brief overview of the terrestrial distribution of boron in rocks, soil, and water, the history of the discovery, early utilization, and geologic origin of borate minerals is summarized....Full Text Available
The Digital Raster Graphic (DRG) is a raster image of a scanned USGS topographic map including the collar information, georeferenced to the UTM grid....
The interaction between core and envelope in stars with central helium burning is investigated. If core and envelope are treated as independent systems, feedback terms arise. All feedback terms are discussed in detail. The approximative treatment of feedback terms in the earlier papers of Lauterborn, Refsdal, and Weigert is found to be fully justified. The problem of secular instabilities in models with central helium burning is rediscussed. (auth)
Many alternative therapies are used as first aid treatment for burns, despite limited evidence supporting their use. In this study, Aloe vera, saliva and a tea tree oil impregnated dressing (Burnaid) were applied as first aid to a porcine deep dermal contact burn, compared to a control of nothing. After burn creation, the treatments were applied for 20 min and the wounds observed at weekly dressing changes for 6 weeks. Results showed that the alternative treatments did significantly decrease subdermal temperature within the skin during the treatment period. However, they did not decrease the microflora or improve re-epithelialisation, scar strength, scar depth or cosmetic appearance of the scar and cannot be recommended for the first aid treatment of partial thickness burns. PMID:18603378
We have studied actinide burn-up in ICF reactor pellets; i.e., 14 MeV neutron fission of the very long-lived actinides that pose storage problems. A major advantage of pellet fuel region burn-up is safety: only milligrams of highly toxic and active material need to be present in the fusion chamber, whereas blanket burn-up requires the continued presence of tons of actinides in a small volume. The actinide data tables required for Monte Carlo calculations of the burn-up of /sup 241/Am and /sup 243/Am are discussed in connection with a study of the sensitivity to cross section uncertainties. More accurate and complete cross sections are required for realistic quantitative calculations.
Small droplets of organic diazides investigated by C.K. Law and coworkers burn in hot gas at 1 atm with rates inversely proportional to the droplet diameter presumably owing to leading chemical reaction proceeds in gas phase. These burning rates are obviously much lower than those obtained by extrapolation of the results measured for the some substances in glass tubes (at pressure of about 10{sup -2}-10{sup -1} atm, and temperature 0-100 deg C) on the burning conditions of the droplets. Kinetic constants estimated using Zel`dovich equation for the burning rate in gas phase and Semenov relation for delay time of the droplets micro-explosion in liquid phase are about the same: E {approx_equal} 0.17 MJ/mol, log{sub 10}k{sub o} {approx_equal} 15(S{sup -1}). In both of the cases the leading chemical reaction is supposed to be of the first order. Landau instability is assumed to be reflected in distortion of ...
Experimental and numerical investigations were performed for the laminar burning velocity and the flame structure of laminar premixed CH{sub 4}/O{sub 2}/CO{sub 2} flames. Measurements of the laminar burning velocity were conducted by using a flame cone angle method for a circular nozzle burner. Numerical simulation was performed using one-dimensional plane flame code including radiation heat loss with an optically thin model. It was shown that the laminar burning velocity decrease with CO{sub 2} addition even though the adiabatic flame temperature is the same as that for CH{sub 4}/Air flames. The radiation heat loss is significant for the CH{sub 4}/O{sub 2}/CO{sub 2}, flames, and the flame temperature and laminar burning velocity decreases when the radiation heat loss is considered. Effects of thermal properties, radiation, and chemical reaction on the determination of the laminar ...
Sep 1, 2011 ... Recent wildfires in interior Alaska have left substantial volumes of burned timber, potentially usable for biomass energy. Motivated,in part, by ...
The effect of burn-up on the thermal conductivity of homogeneous SBR MOX fuel is investigated and compared with standard UO_2 LWR fuel. New thermal diffusivity results obtained on SBR MOX fuel with a pellet burn-up of 35 MWd/kgHM are reported. The thermal diffusivity measurements were carried out at three radial positions using a shielded 'laser-flash' device and show that the thermal diffusivity increases from the pellet periphery to the centre. The fuel thermal conductivity was found to be in the same range as for UO_2 of similar burn-up. The annealing behaviour was characterized in order to identify the degradation due to the out-of-pile auto-irradiation.
Predictions of the combination of our recent model for the formation of planetary nebulae (due to a diverging pulsational instability) together with nuclear-burning shell flashing, with regard to formation of multiple shells, are explored and discussed.
Stabbing paroxysmal pain due to neurological disease can often be controlled by anticonvulsants, whereas steady burning pain is often responsive to tricyclic antidepressants, and to neuroleptics. Overuse...Full Text Available
Jun 16, 2011 ... Description: Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for ...
The helium releases were investigated in FBR fuel pins irradiated to high burn-up. The released amounts increased with the increase of burn-up, but no burn-up dependence of their release fraction to total amounts generated was seen. The contents of "2"4"1Am in fuel pellets affected the released amounts. The effect of released helium on the internal pressure in fuel pins was smaller in FBR fuel pins than in LWR fuel pins, but released helium in fuel pins containing increased amounts of "2"4"1Am, which are anticipated in future FBRs, is expected to affect the internal pressure.
Apparatus and method are described for the vaporization of liquid fuel oils to produce a gaseous mixture suitable for burning in a burner normally designed for operation utilizing natural gas.
In order to quantify the biomass burning emissions, the main atmospheric pollution source of tropical and subtropical regions, we carried out the analysis of ashes that are also formed during these fires. To this end, we developed analytical methods to characterize the composition of savannah grass burning ashes by using X-ray fluorescence for mineral elements and microanalysis for C, H, O and N. Samples used in this work have been collected during laboratory combustion experiments, with chemically well-defined natural savannah grasses from Ivory Coasts and South Africa. The reproducibility and efficiency of different developed procedures have been studies. The analytical relative precision is generally better than 5%. This development has allowed to establish, for the first time, the global mass balance of ashes resulting from savannah grass burning. (authors). 16 refs., 3 figs., 8 tabs.
The Cs-137 radioactivity of a neutron-irradiated nuclear fuel sample has been measured by means of a micro-gamma scanning system which is associated with a high purity Ge detector. Subsequently the burn-up has been calculated from the Cs-137 radioactivity data and then compared with the values from the theoretical computation and chemical anaylsis. The burn-up value obtained with the gamma-scanning system seems to be reasonably agreeable with that of the chemical anaylsis provided that the statistical error in the experiments is taken into account. It is revealed that the burn-up data from the theoretical approach is slightly higher than those of micro-gamma scanning and chemical analysis methods. (Author).
Of some interest is the comparison between the actinide nuclide burning up (fission) rates such as americium 241, americium 242, curium 244, and neptunium 237, in the reactors with fast or thermal neutron spectra.
Of some interest is the comparison between the actinide nuclide burning up (fission) rates such as americium 241, americium 242, curium 244, and neptunium 237, in the reactors with fast or thermal neutron spectra.
A screening questionnaire designed to take an alcohol history was used on 996 patients attending the London Hospital Accident and Emergency Department. Questions concerned with 'binge' drinking detected...Full Text Available
ORDINARY HUMAN REASONING MAY LEAD PATIENTS to provide an unreliable history of past experiences because of errors in comprehension, recall, evaluation and expression. Comprehension of a question may...Full Text Available
Life history theory proposes that early-life cues induce highly integrated responses in traits associated with energy partitioning, maturation, reproduction, and aging such that the individual phenotype...Full Text Available
Clinical features and treatment outcome were compared in depressed outpatients with and without a history of emotional and physical abuse (EPA), including childhood maltreatment. Patients were...Full Text Available
The antibiotic resistance patterns of gram-negative fecal bacteria from pigs in three herds with different histories of antibiotic exposure were examined. In general, smaller proportions of antibiotic-resistant...Full Text Available
Life-history theory predicts that traits involved in maturity, reproduction and survival correlate along a fast–slow continuum of life histories. Evolutionary theories and empirical results...Full Text Available
Aluminum electrolytic capacitors have a long history of reliable operation in unattended field sites. However, their use in the expected space applications ...
This paper gives details of the development of the Wartsila 32DF duel-fuel lean-burn engine that can burn liquid or gaseous fuels, and reports on the installation of four of the engines in Turkey. The combustion process, and the design of the gas admission, pilot fuel, cylinder control, air-fuel control, and engine control and monitoring systems are described. The advantages of the engine are discussed.
The change in concentrations of elements due to transmutations resulting from neutron irradiation in the first wall of the ARIES-IV conceptual fusion energy device were determined as a function of neutron dose. SiC burns out at a rate of about 0.5% per effective full power year. The largest impurity concentration is that of He, but several other elements burn in at rates of hundreds of appm/efpy.
The change of the transport coefficient due to the fusion energy source is studied. The scale invariance property of the reduced set of equations is investigated in the presence of the self-heating term due to the fusion reaction. The pressure gradient as well as the fusion power are the free energy sources that dictate the turbulent transport. It is shown that the burning transport coefficient can have a form with much wider variety, and that the transport property could be different owing to the self-heating by the fusion reactions. (author)
Aerosols affect the radiative energy budget on both the regional and global scales. The wavelength-dependent aerosol optical depth (AOD) is a fundamental determinant of the amount by which extra-terrestrial incoming sunlight and outgoing terrestrial radiation are being attenuated in the atmosphere. The present study addresses the influence of local waste burning on aerosol characteristics, black carbon (BC) aerosol mass concentration and spectral solar irradiance using ground-based measurements over the tropical urban environment of Hyderabad, India. AOD has been observed to be maximum during burning days compared to normal days. Aerosol size spectra suggest bimodal distributions during pre-and post-burning periods and trimodal distributions during burning periods. Angstrom wavelength exponent estimated from spectral variation of AOD suggested dominance of accumulation mode particle loading during ...
This paper presents the results of experimental investigations of the ignition and combustion of plant biofuels (wood particles, date stones) and products of their mechanical and thermal treatment (pellets, charcoal) at temperatures typical of the burning process in nonforced furnaces and fixed-bed and fluidized-bed gas producers. The influence of the furnace heat treatment of a fuel on its inflammation and combustion has been revealed. The results have been compared with the known data on the burning of pellets, brown coals, and anthracites and with the calculation by the classical diffusion-kinetic model.
Accelerated aging tests such as high temperature burn-in, which are in current use on Bendix Kansas City Division's (BKC) purchased small and medium scale integrated circuits, were evaluated to determine if they are effective and necessary to ensure the required reliability. A theoretical analysis, a literature search, and a study of lot acceptance results were used to assess the value of integrated circuit burn-in.
Morphine sulfate (MS Contin), a proven analgesic in the treatment of cancer pain and chronic benign pain, seems to be a good analgesic for the treatment of burn pain. MS Contin is morphine sulfate incorporated in a wax cellulose matrix delivery system. This wax cellulose delivery system gives MS Contin its duration of action. Ten patients were enrolled in an open-labeled, nonrandomized study. The study was designed to examine the analgesic efficacy of MS Contin in the burn population. Each patient remained in the study for 6 days. The efficacy of the analgesic regimen was subjectively measured by the visual pain scale. The MS Contin group was retrospectively compared with a group of patients who were given continuous intravenous infusions of morphine. The two groups were matched according to age, burn size, surgical procedures, and hospital stay. The analgesic qualities of MS Contin were comparable to those of continuous ...
In the present paper it is assumed that above a limiting value of fission fluency (burn-up) a more intensive process of irradiation introduced chemical interaction occurs. A significant part of fission gas product is thus expected to be chemically bounded in the matrix of UO_2 fuel. The fission gas atoms substituting, for example, uranium atoms in the crystallographic lattice can form weak facets. At a certain saturation condition, division of the grains can occur at the weak facets and the increase in fission-gas products release may be expected. The fact that the process of grain division for high burn-ups (70-80 MWd/kgU) forms an extremely fine structure up to the temperature as high as 1100 "oC and simultaneously the observed decreases in fission gas concentration in the fuel supports this concept. The analysis of fission gas concentration change due to the formation of nanostructures in UO_2 fuel at high burn-ups in ...
Theoretical and experimental studies have been carried out on the combustion of azide polymers used as a binder in high-energy propellants. AMMO (3-azidemethyl-3`-methyloxetane) is one of the energetic azide polymers which contain N3 groups in their molecular structures. EDNA (ethylenedinitramine) is a linear nitramine which has modest properties in the flame temperature and the molecular weight of burned gases as compared with HMX (cyclotetramethylenetetranitramine) and NQ (nitroguanidine). In this study, the burning rate characteristics of azide/nitramine propellants were investigated in order to gain a wide spectrum of burning rate. As a result, the burning rate of AMMO/EDNA propellant is higher than that of AMMO/HMX propellant and the pressure exponent of AMMO/EDNA propellant is lower than that of AMMO/HMX propellant. Both AMMO/EDNA and AMMO/HMX propellants exhibited the same combustion wave ...
Summary 1. A primary goal of evolutionary ecology is to understand factors selecting for the diversity of life histories. Life-history components, such as time-to-reproduction, adult survivorship and fecundity, might differ among species because of variation in direct and indirect benefits of these life histories in different environments or might have lower-than-expected variability because of phylogenetic constraints. Here, we present a phylogenetic examination of demography and life histories using a data base of 204 terrestrial plant species. 2. Overall, statistical models without phylogeny were preferred to models with phylogeny for vital rates and elasticities, suggesting that they lacked phylogenetic signal and are evolutionarily labile. However, the effect of phylogeny was signific...
Regular fuel reduction burning is an important management strategy for reducing the scale and intensity of wildfires in south-west Australian native forests, but the long term effects of this on tree and stand growth are not well understood. Five fire treatments, including application of frequent and infrequent low intensity burns, and 25?years of fire exclusion, were applied to small (4?ha) experimental plots in a low rainfall mixed jarrah (Eucalyptus marginata) and marri (Corymbia calophylla) forest to investigate the effects of these treatments on tree stem diameter growth, stand basal area increment and tree mortality. Mean tree stem growth measured over 20?years was lowest in the long unburnt treatment compared with the burn treatments, although surface soil nutrient levels were gener...
Physicists are no strangers to Feynman diagrams, but the meaning of the diagrams is not always clear, even to those who have used them. That confusion has deep roots, as Kaiser clearly and convincingly explains. To Feynman himself, a diagram depicted an actual physical process in space-time, such as the exchange of photons that occurs when an electron and proton collide. However, he also saw it as shorthand for the contributions to the amplitude of a physical process made by the element of the process it depicted. The best part of this new book covers the early history, social history and 'conceptual history' of Feynman diagrams. Disagreements and criticisms aside, the book will be invaluable to historians and sociologists of physics interested in the growth of Feynman diagrams. (U.K.)
This study was initiated to provide empirical data and analyses on the dam passage timing, travel rate, survival, and life history variation of fall Chinook salmon that are produced in the Clearwater River. The area of interest for this study focuses on the lower four miles of the Clearwater River and its confluence with the Snake River because this is an area where many fish delay their seaward migration. The goal of the project is to increase our understanding of the environmental and biological factors that affect juvenile life history of fall Chinook salmon in the Clearwater River. The following summaries are provided for each of the individual chapters in this report.
The founding of the Hanford Engineering Works to produce plutonium is described. The 45-year defense mission has now been replaced with a peaceful mission, that of being the first site for massive cleanup of the 45-year nuclear waste. In order to establish a remedial investigation and feasibility plan, a process of discovery named the Technical Baseline Report must be performed; the task of this process is to discover all that is known about a proposed cleanup site (what the waste was, where did it go). When none of the documentation can answer the question, oral history is utilized. Some of the problems associated with the conduct of oral history interviews are described, particularly Hanford`s legacy of secrecy.
Purpose - The purpose of this paper is to describe the processes and procedures utilized by Jacksonville State University's Houston Cole Library to digitize an oral history collection and provide access to it through the Library's catalog, web presence, and the state-wide digital repository initiative, Alabama Mosaic (see www.alabamamosaic.org). Design/methodology/approach - The paper is based on the Library's experiences in acquiring, digitizing, creating metadata for and making accessible a collection of oral histories. Findings - The paper describes the obstacles overcome, issues encountered, procedures established, and ramifications of the project. Practical implications - Many institutions are currently digitizing unique collections as part of repository initiatives, both institutiona...
It is possible to create nomographs similar to Fig. 2.10 to characterise damage potential of candidate time histories, provided there exists extensive records of earlier time-histories and the damage that they have caused. Thus in order to create such nomographs, one needs the correlated documentation between the input to the structure and the resulting damage. In order to use the Response-Spectra approach, one needs good statistical description of the input to the system. Extensive literature exists on both these methods. The MAC method that has being developed for the present research has yet to be validated. However, if it is successful, it would provide a valuable link between the SEA method and the rational method.
A 37-year-old military mechanic presented to our institution with a chronic history of a slowly enlarging left elbow antecubital fossa mass. There was no history of other chronic illness or trauma. Magnetic resonance imaging (MRI) and excisional biopsy revealed fatty villi and synovial inflammation within the left bicipitoradial bursa, consistent with lipoma arborescens. Four years later the patient presented with a 6-month history of swelling at the antecubital fossa of the opposite elbow. Diagnostic computed tomography and MRI examinations were performed. The surgical and pathologic findings confirmed the imaging diagnosis of lipoma arborescens at the right bicipitoradial bursa. (orig.)
This report presents leaching experiments with irradiated fly ash from the Kozienice Power Station and, as a reference, with a Czechoslovakian fly ash sample. 7 refs, 11 figs, 3 tabs.
A mathematical model was developed to simulate the combustion process of a direct injection diesel engine. The model considers the key features of such a combustion process; namely fuel droplet evaporation, spray formation, mixing, ignition of heterogeneous burning of the fuel. To model mixing, great emphasis was placed on treating both large and small scale aspects of mixing, the model divides the combustion chamber into three distinct regions of air, fuel spray, and a turbulent plume that is formed once ignition occurs. The fuel spray itself is considered to be composed of multiple zones, which in turn are made of cells of equal mass and of different thermodynamic states. Micromixing of the fuel and air cells, within each zone of the jet and the turbulent plume, is then achieved by utilizing the concept of Monte Carlo stochastic coalescence dispersion technique. The frequency of such cell interactions within each zone is obtained by employing a K-1 turbulent ...
Biomass fuel burning leads to high levels of suspended particulate matter and hazardous chemicals in the indoor environment in countries where it is in common use, contributing significantly to indoor...Full Text Available
5 days ago... Sun sensors, 2 secondary Sun sensors, and an Earth sensor. ... This continued intermittently until the rocket burn, at which time ... with incoming asymptotic direction at an angle of -13.6 degrees from the lunar equator. ...
The design and performance of small incinerators used at the Mound Laboratory for the disposal of explosives are described. These units, which cost less than $1000 each, are about the size of a 55-gal drum, have water jackets for cooling, and have provided a flexible, efficient, and clean burning explosives disposal unit. (LCL)
Approximately 62,000 lbs Fuel Load: 58,000 lbs. Type Fuel: JP4, JP5, JP8, JET A, JET A-1, JET B Standard Fuel Burn: 4500 - 6000 lbs/hr depending on altitude and airspeed Maximum...
to end statewide burn ban 09/28/2011 - Commissioner's statement on $80 million biomass to jet fuel award to UW and WSU Media Center | View All News Meetings & Events Saturday Oct...
BackgroundBlood sampling through heel lancing is the most common invasive painful procedure performed on newborn infants.Case PresentationWe report...Full Text Available
This study determined how well crude and fuel oils burn on water. Objectives were: (1) to measure the burning rates for several oils; (2) to determine whether adding heat improves the oils' combustibility; (3) to identify the conditions necessary to ignite fuels known to be difficult to ignite on ocean waters (e.g., diesel and Bunker C fuel oils); and (4) to evaluate the accuracy of an oil-burning model proposed by Thompson, Dawson, and Goodier (1979). Observations were made about how weathering and the thickness of the oil layer affect the combustion of crude and fuel oils. Nine oils commonly transported on the world's major waterways were tested. Burns were first conducted in Oklahoma under warm-weather conditions (approx. 30/sup 0/C) and later in Ohio under cold-weather conditions (approx. 0/sup 0/C to 10/sup 0/C).
The state of the art of our understanding of combustible cartridge cases is presented. The report, after a background section, discusses the models that exist today and presents new models of combustible cartridge case burning. Following a summary of expe...
... days after it burned, using a portable spectroradiometer (704 bands in the range 0.35 to 2.5 mu m) and an infrared thermometer (one band, 6 to 14 mu m). ...
The techniques of thermogravimetry and derivative thermogravimetry (dTG) have been applied to a range of fuel oils and two 'fingerprinting' tests have been developed, one using an inert and the other an oxidizing atmosphere. These tests have been named evaporation profile and burning profile. 4 refs.
Only half of the carbon dioxide produced by burning fossil fuels stays in the atmosphere. It is thought that the oceans absorb the rest. To understand the world's climate it is necessary to know how the atmosphere, ocean and biosphere interact.
In nuclear fuel with a burn-up of 33 kg/t U and 52 kg/t U 15 transuranium nuclides /sup 237/Np to /sup 246/Cm have been determined by alpha and gamma spectroscopy after radiochemical separation.
Very few areas of medical science have experienced more rapid development of new and beneficial treatment approaches during the past two decades than the disciplines required for total care of patients...Full Text Available
Subcommittee of the Joint Committee on Atomic Energy of the United States, Outer Space Propulsion by Nuclear Energy, hearings, 85th Cong., 2d sess., 22, ...
David N. Spires and Rick W. Sturdevant, "From Advent to Milstar: The United States Air Force and the Challenges of Military Satellite Communications. Chapter 8 ...
Ever-present water vapor and dust distort or block incoming radiations. ... were among the first scientific sensors to be attached to the earliest space rockets. ...
as manufacturing plants and laboratories, including the Chemical Laboratory at the House of David in Benton Harbor, Michigan. Built in America: Historic Building Buildings Survey/...
... written history concerning the use of the military working dogs in Vietnam. ... oral) to compile a historical account of the military working dog in Vietnam ...
... water content according to the hydrometeor type. ... the documentation and the movement personnel and ... Dyer, RM, 1970: Particle fall speeds within ...
... Abstract : Small metallic fragments can be trapped in combustible cartridge cases during manufacture and released into the interior-ballistic flow ...
The Nobel lecture of Chandrasekhar is printed in which he describes the basic processes that determine the life history of a star with particular emphasis on the roles of stellar mass and radiation pressure. (AIP)
"Report of the Ad Hoc Subpanel on Reusable Launch Vehicle Technology. ... The author comments that the United State's space transportation system is ...
BackgroundA large and increasing part of the European population has a history of migration. Germany, for example, is home to about 15 million people with migrant background, which...Full Text Available
Physician reimbursement and the coding to support it are critically important to the sustained health of any physician's practice. This article reviews the recent history of physician reimbursement...Full Text Available
turbine (VAWT) is given, followed by a short history of its ... represents the most cost-effective blade for the Darneus-type VAWT. (Author). A79-14322 ...
... with the symptoms of MS have MS. Diagnosis Physical examination and medical history are very important in diagnosing MS. Physical exams include a variety of tests to check ...
... Pan Flu Preparedness YouTube is Your Friend Additional Resources ... Response Hurricane Readiness in High-Risk Areas: Survey Results Elements of ...
OBJECTIVEAdolescent offspring of women with a history of gestational diabetes (GD) were evaluated for their cardiometabolic risks at a mean age of 15 years.RESEARCH...Full Text Available
Little is known about the state of experimentation in the field of medicine during the Medieval Islamic era. With few exceptions, most of the contemporary sources on history of medicine propagate the...Full Text Available
Sep 5, 1996 ... In Haiti, the military deployed a space support team to advise the task force commander on the effective use of space assets, such as the Milstar ...
With the increased costs of maintaining boilers and chillers entrepreneurs around the country have offered magnetic and similar devices to facilities as viable alternatives to their maintenance program. This report gives a brief history of some of the pre...
Jan 14, 2004 ... presented to the nation at NASA Headquarters, Washington, D.C., ...... Board/Air Force Scientific Advisory Board Joint Task Force on ...
A 6-week-old girl with fever, hypernatraemia, dehydration, and polyuria failed to concentrate urine in response to exogenous vasopressin administration. There was no family history of nephrogenic diabetes...Full Text Available
... 4? Program History 5? Center for Advanced Materials and Smart Structures 6? Center for Systems ... Systems 14? Center for Photonic Materials Research 15? Synthesis, Manufacturing and Characterization ...
Mixed Uranium Plutonium Carbide ((U, Pu) C), in the form of pellets encapsulated in stainless steel tubes is the fuel for Fast Breeder Test Reactor (FBTR) at Kalpakkam. For the fabrication of fuel for enlarging the core of this reactor, high burn up plutonium is used. The external exposure in these labs was significantly higher than that with low burn up Pu fuel. Dose evaluation to the organs was carried out using experimental TLDs during various operations of FBTR fuel fabrication to study the dose distribution pattern. (author)
A high-voltage cathode initiates an electron emission, resulting in a reduction in the carbon dioxide concentration in exhaust gas from the burning of hydrocarbon fuel. Assuming that the observed carbon dioxide reduction is originated from the molecular decomposition, the energy needed for the endothermic reaction of this carbon dioxide reduction may stem primarily from the internal energy reduction in the exhaust gas in accordance of the first law of the thermodynamics. An oxygen increase due to the reduction in carbon dioxide in a discharge gas was observed in real time.
The purpose of this study was to determine if nitrogen loss from prescribed fire can be mitigated by reducing the amount of large fuel on a clearcut prior to burning. We examine the relations between nitrogen loss and duff consumption by prescribed fire with respect to the amount of woody biomass on the unit and the moisture content of that biomass before burn. Equations are presented to predict duff consumption from preburn conditions. Sources of variability of nitrogen concentration and content of duff within and between units are also evaluated.
Directionally solidified nickel-based superalloy DZ4 is an important structural material. However, the grinding burn occurs in grinding processes has hindered the grinding efficiency and dimensional accuracy. This paper investigates the grinding mechanism of this new type of superalloy based on the systematical analyses of variable characteristics of the grinding force, grinding temperature, topography of ground surface, hardness distribution of surface layer, as well as morphology of surface layer from a metallographical point of view. The results will be beneficial to grinding the superalloy with high efficiency and high precision. (orig.)
The effect of variations of the fundamental constants on the thermonuclear rate of the triple alpha reaction, "4He(#alpha##alpha#, #gamma#)"1"2C, that bridges the gap between "4He and "1"2C is investigated. We have followed the evolution of 15 and 60 M#centre dot# zero metallicity stellar models, up to the end of core helium burning. They are assumed to be representative of the first (Population III) stars. The calculated oxygen carbon abundances resulting from helium burning can then be used to constrain the variation of the fundamental constants.
The Hanford Site in eastern Washington state currently is engaged in the largest waste cleanup in world history. In order to make informed decisions about remediation options, the public throughout the Pacific Northwest and the nation needs to understand the wastes that are present, their sources of generation, their composition, and their behavior in the environment. The fact that Hanford operations` were conducted in secret for over four decades presents a unique public information challenge to those who currently are responsible for communicating with the public.
This study examined the life histories of a group of emerging scholars in the field of mathematics education who identify themselves as having a particular interest in and concern for issues of equity and diversity. Experiences of being the "other," "bearing witness" to "othering experiences," and "orienting experiences" in relation to issues of equity proved to be prominent themes in participants' life histories. These experiences were then linked to the positionality that these scholars now have in relation to their research in mathematics education.
In this brief article I review the history of astronomical photometry, touching on observations made by the ancient Chinese, Hipparchus and Ptolemy, the development of the concept (and definition) of magnitude, the endeavors of Argelander and Zoellner, work at Harvard at the end of the 19th century, and the development of photography, photomultipliers, and CCD's and their application to astronomy.
The elemental and mineralogical variation in a self-burning coal seam from Coalspur, Alberta, is determined using instrumental neutron activation analysis (INAA) and x-ray diffraction (XRD). The elemental variation in the coal seam is related to temperatures in the various alteration zones, i.e., oxidation, combustion, or carbonization and nature of elements. Mobilization of elements is greatest for As, Br, Cl, Mo, N, S, and Sb. Some of these elements are released to the atmosphere, as evident by the presence of orthorombic sulfur crystals on the surface or in vents at the top of the burning seam or saturation of oxidation char by volatile matter (tar). Whewellite (CaC{sub 2}O{sub 4}, H{sub 2}O) is the only Ca-bearing mineral found in the cooler area of the coal seam. Decomposition of this mineral, coupled with the presence of SO{sub 2} formed by reaction of organic sulfur with O{sub 2} in combustion, resulted in formation of a relatively high ...
Samples from a burning bituminous coal seam from Coalspur, Alberta, were studied by reflected light microscopy. Two zones - namely oxidation- combustion and distillation - were detected in the seam. Near the surface, the oxidation zone contained chars showing cracks and oxidation rims. The cracks were filled with fluorescing hydrocarbon material formed by thermal cracking of coal macerals. The chars in the deeper part of the oxidation zone had a carbonized matrix and burnt rims. The distillation zone covered most of the coal seam. Chars were mostly in the precarbonization stage, except those immediately below the combustion zone or near the base of the seam. Precarbonized chars contained pyrolytic carbon in some horizons. The distilled chars were formed by heat generated by combustion at the top of the seam and also by heat transfer from an underlying burning seam through an intermediate clastic layer. The minimum temperature of formation of ...
Laser frequency stabilization giving a 500-Hz Allan deviation for a 2-ms integration time with drift reduced to 7 kHz/min over several minutes was achieved at 1536 nm in the optical communication band. A continuously regenerated spectral hole in the inhomogeneously broadened "4I_1_5_/_2(1)#->#"4I_1_3_/_2(1) optical absorption of an Er"3"+:Y_2SiO_5 crystal was used as the short-term frequency reference, while a variation on the locking technique allowed simultaneous use of the inhomogeneously broadened absorption line as a long-term reference. The reported frequency stability was achieved without vibration isolation. Spectral hole burning frequency stabilization provides ideal laser sources for high-resolution spectroscopy, real-time optical signal processing, and a range of applications requiring ultra-narrow-band light sources or coherent detection; the time scale for stability and the compatibility with spectral hole burning devices make ...
Understanding feedbacks between terrestrial and atmospheric systems is vital for predicting the consequences of global change, particularly in the rapidly changing Arctic. Fire is a key process in this context, but the consequences of altered fire regimes in tundra ecosystems are rarely considered, largely because tundra fires occur infrequently on the modern landscape. We present paleoecological data that indicate frequent tundra fires in northcentral Alaska between 14,000 and 10,000 years ago. Charcoal and pollen from lake sediments reveal that ancient birchdominated shrub tundra burned as often as modern boreal forests in the region, every 144 years on average (+/- 90 s.d.; n = 44). Although paleoclimate interpretations and data from modern tundra fires suggest that increased burning was aided by low effective moisture, vegetation cover clearly played a critical role in facilitating the paleo-fires by creating an abundance of fine fuels. ...
NO[sub x] emission legislation requirements for large-bore internal combustion engines have required engine manufacturers to continue to develop and improve techniques for exhaust emission reduction. This paper describes the development of the Cooper-Bessemer Clean Burn gas-diesel (dual-fuel) engine that results in NO[sub x] reductions of up to 92 percent as compared with an uncontrolled gas-diesel engine. Historically, the gas-diesel and diesel engine combustion systems have not responded to similar techniques of NO[sub x] reduction that have been successful on straight spark-ignited natural gas burning engines. NO[sub x] levels of a nominal 1.0 g/BHP-h, equal to the spark-ignited natural gas fueled engine, have been achieved for the gas-diesel and are described. In addition, the higher opacity exhaust plume characteristic of gas-diesel combustion is significantly reduced or eliminated. This achievement is considered to be a major ...
In 18 piglets, weighing 10-15 kg, third-degree burns or full-thickness skin excisions of 4 X 4 cm were inflicted. The effect of five dressing materials on adhesiveness to the wounds, appearance, conformability, wound contraction, bacterial count, and morphology of the wound was studied at the end of the seventh and fourteenth days without dressing changes. In 11 piglets with a burn wound, the most adherent dressing was collagen sponge(CS), followed by polyurethane sponge (PU), pigskin xenograph (PS), and xeroform. CS more effectively debrided the wound from coagulated necrotic tissue than the other dressings. Wound contraction was maximal with CS dressing (52%), followed by PU (44%), xeroform (32%), and PS (27%). In another seven piglets with full-thickness excised wounds, a velour dressing made of polytetrafluoroethylene (PTFE) or PU adhered significantly more than CS or PS. Wound contraction was greater with CS (37%) or PTFE (35%) than with ...
This paper presents a numerical study on the formation history of coalbed methane (CBM) reservoir in the southeast edge of Ordos Basin, China. The coal seams studied belong to the Late Palaeozoic coal-bearing series. These coal seams have a burial history and experienced the process of subsidence, rapid subsidence alternated with uplift and then uplift, sequentially, and underwent the geothermal actions at normal, extremely high, and then normal temperatures, respectively. Coal organic matter of the coal seams matured in the Triassic Period and in the Late Jurassic to Early Cretaceous Period. The results from numerical simulation reveal that CBM reservoir evolution history can be classified into five stages, namely primary, initial, stagnant, active and dissipative stages. In the first (pr...
This report describes a simple seismic analysis model of the KALIMER-600 sodium cooled fast reactor and its application to the seismic time history analysis. To develop the simple seismic analysis model, the detailed 3-D finite element analyses for main components, IHTS piping system, and reactor building were carried out to verify the dynamic characteristics of each part of simple seismic analysis models. By using the developed simple model, the seismic time history analyses for both cases of a seismic isolation and non-isolation design of KALIMER-600 were performed. From the comparison of the calculated floor response spectrum, it is verified that the seismically isolated KALIMER-600 reactor building shows a great performance of a seismic isolation and assures a seismic integrity.
Using a case-study, inductive, narrative approach, this article explores the history, drivers, benefits, and barriers to the Bakun Hydroelectric Project in East Malaysia. Situated on the island of Borneo, Bakun Dam is a 204m high concrete face, rock filled dam on the Balui River in the Upper Rajang Basin in the rainforests of Sarawak. Bakun Dam and its affiliated infrastructure could be the single largest and most expensive energy project ever undertaken in Southeast Asia. Based on data collected through site visits, original field research in Sarawak, and more than 80 research interviews, the article begins by teasing out the complex history and drivers behind the Bakun project before identifying a set of potential social, political, and economic benefits the project could deliver. It the...
Since The Meaning of Evolution (1992), Robert J. Richards has argued that modern evolutionary theory is rooted in late 18th-century Romantic science. The publication of The Tragic Sense of Life (2009) provides a fitting occasion to evaluate how this perspective revises the standard history of biological thought. This essay focuses on three aspects of Richards's attempt to rehabilitate the reputation of German Naturphilosophie: (1) the identification of Romantic strains in Charles Darwin's portrait of evolutionary history; (2) the demonstration that any attempt to treat Ernst Haeckel as a "pseudo-Darwinian" inevitably renders Darwin himself a "pseudo-Darwinian"; and (3) the denial of Haeckel's alleged responsibility for the rise of Nazi racial hygiene. This article examines Richards's case for clearing Haeckel's name, as well as the subsequent (slanderous) charge from Daniel Gasman that Richards is guilty of whitewashing the Haeckelian roots of ...
The University of Maryland at Baltimore was awarded a grant from the Department of Energy to test a specially modified incinerator to burn biomedical radioactive waste. In preparation for the incinerator, the Radiation Safety Office devised a comprehensive plan for its safe and effective use. The incinerator plan includes a discussion of regulations regarding on-site incineration of radioactive waste, plans for optimum use in burning four principal waste forms, controlled air incineration technology, and standard health physics safety practices; a use plan, including waste categorization and segregation, processing, and ash disposition; safety procedures, including personnel and area monitoring; and methods to evaluate the incinerator's effectiveness by estimating its volume reduction factors, mass and activity balances, and by determining the cost effectiveness of incineration versus commercial shallow land burial.
Natural gas is a promising alternative fuel to meet strict engine emission regulations in many countries. Natural gas engines can operate at lean burn and stoichiometric conditions with different combustion and emission characteristics. In this paper, the operating envelope, fuel economy, emissions, cycle-to-cycle variations in indicated mean effective pressure and strategies to achieve stable combustion of lean burn natural gas engines are highlighted. Stoichiometric natural gas engines are briefly reviewed. To keep the output power and torque of natural gas engines comparable to those of their gasoline or Diesel counterparts, high boost pressure should be used. High activity catalyst for methane oxidation and lean deNOx system or three way catalyst with precise air-fuel ratio control str...
A micronized de-ashed coal-water slurry (CWS) fuel of approximately 50% coal loading has been successfully ignited and burned in one GE 7FDL engine cylinder at 1050 rpm. For this study, only about one-third of the full load fuel energy was supplied due to limitations of the fuel injection equipment used. Three types of ignition methods have been investigated. They were: Compression ignition with no ignition aid; Separate deisel pilot fuel injection to ignite the CWS fuel; Combined CWS and pilot diesel fuel injection (stratified pilot ignition). Conditions of ignition and the burning characteristics that immediately followed using the above three ignition methods are described.
Abstract Purpose: We investigated the effects of various rinsing and healing protocols on corneal wound repair and inflammation following alkali burn in rabbits. Methods: We conducted in vitro, in vivo and ex vivo studies. First, different rinse solutions were tested in vitro after incubation of ocular cells with methanol or NaOH. Cell viability was then assessed using the neutral red test (cytofluorometry). Second, NaOH was applied to rabbit corneas and associations of rinse solutions (NaCl 0.9% or controlled ionization marine solutions) with N-acetylcysteine or vegetable oils (from Calophyllum inophyllum and Aleurites moluccana) were tested in vivo. The regeneration of the corneal epithelium and the infiltration of inflammatory cells were evaluated using in vivo confocal microscopy and e...
A neutron scanning device was developed in order to obtain accurate neutron intensities of high burn-up BWR fuels. This scanning device was calibrated with a "2"5"2Cf source and used to measure axial distributions of neutron intensities of BWR fuels with various enrichments (2.0%-3.4%) irradiated up to 60 GWd/tU at Fukushima Daini Nuclear Power Station Unit 2(2F-2). The measured neutron intensities were approximated well with power law interpolations on the calculated burn-up values. The neutron intensities calculated by the ORIGEN2-86 code showed good agreements with the measured ones within 20%. (author)
We report the delayed sequelae arising in a case of electrical injury, reviewing the literature on the subject and focusing on the MRI findings of the brain. A 23-year-old male suffered burns to the left parietal scalp, both feet, and the anterior chest wall. Neurological symptoms and MRI abnormalities appeared 14 days after the insult and continued for about three months. T1-weight MR images demonstrated homogeneous hypointensity, while T2-weighted images depicted hyperintense finger-like projections. Contrast-enhanced T1-weighted images demonstrated strong band-like enhancement, indicating meningeal hyperemia. Follow-up MR imaging showed that the lesion had disappeared, indicating that the cerebral edema and meaningeal hyperemia were reversible.
A new combustion system for a small direct injection diesel engine has been developed, with a spheroidal cavity and swirl nozzle characterized by weak spray penetration and wide spray angle. This system is intended to realize air-borne mixture formation and good combustion processes over wide operating ranges. In-cylinder observations of the system reveal that droplets are easily bent in the direction of air movement, ignition occurs near the spray tip, and the flame is hard to envelop the spray. In a single cylinder engine of 460 cm/sup 3/ swept volume, the system realizes active diffusion burning and mild premixed burning despite of long ignition delay, and provides low fuel consumption and low smoke emission, especially at low speeds.
Composed of Sun sensors, the Canopus sensor, the inertial reference unit, ... The heart of the system was a 100-pound-thrust rocket whose hypergolic, ... The spacecraft's low-gain antenna picked up all incoming signals from the NASA-JPL ...
Incoming solar energy had to be assimilated to sustain it. .... Roll stability was achieved with an Earth sensor mounted on the directional antenna. .... Once more a rocket becomes the means of producing a vector change in velocity. ...
Sunlight exposure has been suggested as a cause of AMD. To examine this, we collected detailed histories of ocular sun exposure in 838 watermen who work on the Chesapeake Bay. The presence and severity...Full Text Available
To date few reports have provided direct comparison of psychosocial vulnerability and resources among youth with victimization and perpetration histories. Within a racially diverse, high-risk...Full Text Available
Background and objectives: The pathogenesis of acquired nephrogenic systemic fibrosis recently described for patients with renal insufficiency and a history of exposition to gadolinium-based magnetic...Full Text Available
... a woman with a history of PID, perhaps endometriosis -- or some limited vaginal access because of the ... I'm doing an oophorectomy or, you know, endometriosis case where we need to use bipolar sealing ...
The difficulties created by the lack of generally accepted views on classification, diagnostic criteria and natural history of the cutaneous lymphomata are discussed. Only the lymphomata which remain...Full Text Available
Background and AimsTrade-offs are fundamental to life-history theory, and the leaf size vs. number trade-off has recently been suggested to be of importance to our understanding...Full Text Available
Small metallic fragments can be trapped in combustible cartridge cases during manufacture and released into the interior-ballistic flow upon combustion of the case. Such particles may survive the interior-ballistic cycle and pose an ignition threat to the...
BackgroundThe natural history of bronchial preinvasive lesions and the risk of developing lung cancer in patients with these lesions are not clear. Previous studies have treated...Full Text Available
A review is presented of the quest for superheavy elements under the following headings - early history; physical and nuclear properties unique to superheavy elements; searches in nature; terrestrial samples; extra-terrestrial samples; and searches at accelerators. 72 references. (U.K.).
This book chapter discusses sugarcane culture and history, describes arthropod biologies and injury, and identifies sugarcane pest management factors to consider for people interested in commercial sugarcane production. Arthropod groups include 10 orders and 40 families. Sugarcane pest management ...
Spontaneous spinal epidural hematoma is a rare cause of acute spinal cord compression. A 25-year-old male presented with a history of sudden onset of complete quadriplegia with sensory loss below the...Full Text Available
BackgroundCholera has claimed many lives throughout history and it continues to be a global threat, especially in countries in Africa. The disease is listed as one of three internationally...Full Text Available
Objective:This article examines relationships between reproductive onset and lifetime history of smoking, regular smoking, and nicotine dependence, and cannabis and other illicit...Full Text Available
During 1975 we studied 100 patients--77 men and 23 women--who had a history of alcohol abuse and disturbed liver function test results. On presentation the women were less likely to be suspected of...Full Text Available
... its infancy. However, the geological record of many fossil fungi is well established (Elsik, 1996; Kalgutkar and Jansonius, ... 1988). A comprehensive account of the history of fossil fungi, and the impor...
The cumulative rate of childhood eczema during the first three years was studied in a birth cohort of 1265 New Zealand infants. A parental history of eczema was the strongest predictor of rates of childhood...Full Text Available
BackgroundSynonymous sites are freer to vary because of redundancy in genetic code. Messenger RNA secondary structure restricts this freedom, as revealed by previous findings in...Full Text Available
Spectacular increases in the quantity of sequence data genome have facilitated major advances in eukaryotic comparative genomics. By exploiting homology with classical model organisms, this makes possible...Full Text Available
The history of the Arabian Gulf region shows a lot of commonality in the six states which form the Gulf Cooperation Council (GCC). Their shared heritage ranges from common colonial masters to common religion and language. Because of their oil wealth and, ...
BackgroundWhile prepubertal nutritional influences appear to play a role in sexual maturation, there is a need to clarify the potential contributions of maternal and childhood influences...Full Text Available
Poland's anomaly is an uncommon congenital aberration of the chest wall characterized by absence of the pectoralis major muscle and other nearby musculoskeletal components. In this series, a wide spectrum...Full Text Available
We present a rare case of pagetoid reticulosis arising in a five year old white boy. He had a history of a large chronic erythematous, scaly patch on his left buttock that had shown intermittent...Full Text Available
A urethrorectal fistula was diagnosed in a 10-week-old, intact male bulldog, presented with a history of urine dribbling from his anus. The fistula was ligated using a novel perineal approach, resulting...Full Text Available
It is shown that a natural consequence of the binary pulsar's evolution is a neutron star collision. Such a collision is expected to eject neutron-rich matter of an r-process character. Taking reasonable estimates for the number of such events over the history of the galaxy, it may be that they account for all of the r-process nuclei.
Objective: To highlight the key differences in history, examination, and management of pyoderma gangrenosum and necrotizing fasciitis and to outline the importance of distinguishing these...Full Text Available
BackgroundMutations that impair mitochondrial functioning are associated with a variety of metabolic and age-related disorders. A barrier to rigorous tests of the role of mitochondrial...Full Text Available
... recognized in the genus in which one inhabits forest litter and the other inhabits streams (Verdade, 2005). The forest litter species deposit their eggs in humid habitats, with ... ...
Jan 15, 2004 ... thought I would have a difficult time working with. ...... they were absolutely right, because everybody said it rained cats and dogs on the orbit ...... We know that in the military. You can ask any military ...
Study of cloud pictures taken from rockets, such as figure 1, indicates that it is .... One might visualize a "Satellite Weather Data Center" where incoming data would ... about 300 miles; satellite packaging, containing the sensors, storage, power, ...
... on a transgressive surface; examples from the Silurian Whirlpool Sandstone of southern Ontario, Canada. Journal of Sedimentary ... and C. J. Salas. 1991. The Lower Silurian Whirlpool Sandstone. in Cheel, ...
A Legionella-like organism, strain 1677-MI-H, was isolated from the bronchoscopy washings of a patient with pneumonia who had a 2-year history of progressive, chronic lymphocytic leukemia. The growth...Full Text Available
A 57-year-old man with a history of coronary artery disease and placement of an implantable cardioverter-defibrillator presented at our emergency room with an anterior ST-elevation myocardial infarction....Full Text Available
An ex-employee's claims that inadequate enforcement of radiation safety regulations allowed excess radiation exposure thereby causing his deteriorating health was not substantiated by a thorough investigation.
The University of Cincinnati (UC) has been active in the National Library of Medicine's Integrated Advanced Information Management Systems (IAIMS) program since IAIMS' inception in 1984. UC received...Full Text Available
A 37 year old male was referred to our centre for management of episcleritis with peripheral keratitis in the right eye. He had a history of ocular discomfort in the right eye of 1 week duration. Slitlamp...Full Text Available
Idiopathic or functional abdominal pain (FAP) is common in school-age children and typically reflects a functional gastrointestinal disorder (FGID). FGIDs in adults have been distinguished by...Full Text Available
Aquaculture is increasing worldwide, however we have little understanding of its impacts on marine communities. A critical element of many marine communities are seagrasses, a group of globally distributed marine angiosperms that are drivers of many abiotic and biotic processes in estuarine and mari...
... Hospital & University Hospital Basel) If I Had - Pre-diabetes - Dr. Venkat Narayan, MD, MSc, MBA, Rollins School ... School, Massachusetts General Hospital, Discusses the Treatment of Diabetes Back to Home Page If I Had - A ...
Of 868 patients admitted with pancreatitis between 1971 and 1976, coexisting hyperbilirubinemia was noted in 125 (14%). The patient population was primarily composed of alcoholics (84%) with chronic...Full Text Available
This monograph explores an alternative way of providing a JSOTF headquarters to the Joint Force Commander. Beginning with a history of joint SOF doctrine, the monograph outlines the evolution of special operations command and control and the subsequent ne...
AimsTo identify the completeness of documentation of Complementary And Alternative Medicine (CAM) use in hospital medical records of patients before and after an education programme.Full Text Available
Glossitis among U.S. military working dogs in South Vietnam was characterized by variable redness and loss of papillae on the anterodorsal third of the tongue; salivation, drooling, and inappetence were the principal clinical signs. Symptomatic treatment ...
Natural accumulations of skeletal material (death assemblages) have the potential to provide historical data on species diversity and population structure for regions lacking decades of wildlife monitoring,...Full Text Available
SummaryThe evolutionary pressures that shaped the specificity and catalytic efficiency of enzymes can only be speculated. While directed evolution experiments show that new functions...Full Text Available
Loss of biological diversity because of extinction is one of the most pronounced changes to the global environment. For several decades, researchers have tried to understand how changes in biodiversity...Full Text Available
Contemporary Western medicine has witnessed a fragmentation of our conceptualization of the medical endeavor into ‘traditional medicine’ and ‘non-traditional medicine’....Full Text Available
Examination of a painful hip is fairly concise and reliable at detecting the presence of a hip joint problem. Hip joint disorders often go undetected, leading to the development of secondary disorders....Full Text Available
This document is the published result, conclusion, or progress report of research performed by the staff of the U.S. Geological Survey, Fort Collins Science ... ...
The objective of this experiment was to determine the effect of dietary grain on calcium homeostasis. Six rumen-fistulated dairy cows with 3 or more previous lactations and no history of parturient...Full Text Available
The Calorie (kcal) of present U.S. food labels is similar to the original French definition of 1825. The original published source (now available on the internet) defined the Calorie as the quantity...Full Text Available
We have discovered interstellar rubidium by observing the resonance line of Rb I at 7800 A toward zeta Oph. This is the heaviest element yet detected within the interstellar medium, and our detection of this element is important for understanding the history of nucleosynthesis in the solar neighborhood.
The earliest clinical evidence of diabetic nephropathy is microalbuminuria. Progression from microalbuminuria to overt nephropathy occurs in 20-40% within a 10-year period with approximately 20% of...Full Text Available
Evolutionary explanations for life history diversity are based on the idea of costs of reproduction, particularly on the concept of a trade-off between age-specific reproduction and parental survival,...Full Text Available
This study investigates the contributions of the military working dogs in Vietnam to determine their significance to the United States' war effort. There is limited written history concerning the use of the military working dogs in Vietnam. The methods an...
Colorectal cancer is extremely rare in children. We report a case of a 12-year-old boy who presented with a five-month history of weight loss and anorexia, associated with vomiting episodes, dizziness,...Full Text Available
is approximately 327000 km from the Earth's center (58000 km from the Moon's ...... source (figure 7-4). NEXT developed funding requirements for those ...... Code SF 2. 2101 NASA Rd. 1. Houston, TX 77058. Phone: (281) 483-7224 ...
AbstractA 6-month-old female alpaca was presented for stranguria. Based on the history, physical examination findings, and radiographic studies, the alpaca was diagnosed with bladder...Full Text Available
A survey was conducted at 15 textile plants with dyehouses in western Sweden. Employees with a history of work related rhinitis, asthma, or skin symptoms were offered a clinical and immunological investigation...Full Text Available
BackgroundMost analyses of spatial clustering of disease have been based on either residence at the time of diagnosis or current residence. An underlying assumption in these analyses...Full Text Available
BackgroundEvolutionary life history theory predicts that, in the absence of contraception, any enhancement of maternal condition can increase human fertility. Energetic...Full Text Available
Alton Ochsner was a giant of American surgery. His career encompassed patient care, teaching, and research as symbolized on the original seal of the Ochsner Clinic. His ideas were innovative and groundbreaking...Full Text Available
This work deals with a rational vision of stratospheric ozone including the threats on ozone layer, the verifications and the fears. After a recalling on the ozone layer history, the authors treats the question of the ultraviolets particularly the beneficial effects. Then an explanation of the ozone layer decrease is given. (O.L.). 29 refs., 6 figs.
How learning and memory is achieved in the brain is a central question in neuroscience. Key to today’s research into information storage in the brain is the concept of synaptic plasticity, a...Full Text Available
increased knowledge as result of about a year's work, has led us first to ...... James Webb: And the advanced technology on which military power is going to be ..... on the road and I've been with the real big dogs and I know the deal ...
A case study of a small-scale hydroelectric plant to identify implementation problems is presented. The Montello hydroelectric plant is described including the background and history of the plant, the physical characteristics, the financial history and costs, operation, regulatory agencies, and the problems encountered in its operation. The analyses of the energy and capacity (demand) credits for the Montello hydroelectric plant when it is added to the Wisconsin Power and Light Company generating system is described. The WP and L base case and the results of the analyses are discussed. (WHK)
This talk reviews the history of the Canadian nuclear-electric program highlighting Canada's first nuclear power station, the Nuclear Power Demonstration or NPD. NPD was commissioned and delivered electricity to Canadian consumers for the first time on june 4, 1962. The Canadian nuclear-electric program is based on the CANDU-PHW (Canadian Deuterium Uranium - Pressurized Heavy Water) concept which was conceived between 1955 and 1958 at the Chalk River Nuclear Laboratory (CRNL) of AECL, located a few miles from Deep River. This talk covers the history of the Canadian nuclear-electric activities dating back to 1939.
In recent years, several groups, including the physician assistant, health information management, ophthalmic medical technician/technologist, and athletic training review committees, have left the Commission on Accreditation of Allied Health Education Programs (CAAHEP) system to form their own, profession-specific accrediting bodies. Their motivation was typically a desire for greater professional visibility and autonomy. Combined, these professions represented one third of the CAAHEP's programs. This article reviews the history of allied health and examines current attempts to bring cohesion and identity to this increasingly fractured segment of the U.S. health care system. PMID:18444439
We have measured the frequency-dependent dielectric function of semi-crystalline polybutylene terephthalate (PBT) in the terahertz region between 100?GHz and approximately 2.8?THz. A characteristic band is observed around 2.38?THz. The intensity of this band is a good indicator of the degree of crystallinity of the different samples. A potential assignment of this band is proposed, based on the comparison with spectroscopic data of the structurally very similar polyethylene terephtalate (PET). Furthermore, the frequency-dependent index of refraction of PBT reveals more insight about the morphology and different thermal history of the samples under investigation.
The technical development of electric cables in the history of the Berlin electric utilities looks back on more than one century of continuous progress from jute-insulated direct-voltage cables, to 30 kV paper-insulated mass-impregnated cables, 110 kV plastic-insulated cables, 380 kV oil-filled cables, and 380 kV XLPE cables which are increasingly used today. A brief review informs about the major stages of power cable development. (orig.).
In Pressurised heavy water reactors (PHWRs), neutron poison in the moderator is used to compensate the excess reactivity present in the core on different occasions such as xenon decay during synchronization just after poison out period or start ups from xenon free conditions. It is also used in secondary shutdown system (SDS-2), where required amount of neutron poison is injected directly into the moderator within 2.5 seconds. Further, it is also used for over poisoning the moderator to achieve the guaranteed shutdown state when the regular shutdown systems are taken for maintenance. Generally, two types of moderator poisons are used in power reactors to balance the reactivity of the core and they are boron and gadolinium. Gadolinium is used in the form of gadolinium nitrate (Gd(NO3)3.6H2O). The paper gives the details of estimation of reactivity coefficients of gadolinium for 540 MWe PHWR for different operating conditions. These neutron poisons are converted into non-absorbing ...
This patent describes a turbocharger for a two-cycle engine having an oil mist containing crankcase and burning a mixture of liquid fuel containing lubricating oil therein wherein the turbocharger comprises a shaft mounted in a housing for rotation by an exhaust-driven turbine on one end to a drive compressor on the other end connected to supply pressurized air for the fuel/air mixture of the engine, the improvement to supply lubrication to the shaft and automatically enrichen the fuel/air mixture during high speed turbocharging.
Modern particle accelerators offer new opportunities to dramatically reshape the way we think about nuclear energy, and challenge some of the thorniest problems linked to its industrial use, e.g. nuclear waste. A powerful proton accelerator driving a sub-critical fission reactor could be used for producing energy more safely and burning up the extra spent fuel which so far has been stored in geological repositories.
In China, the conventional utilization of oil shale is concentrated mainly on oil shale retorting, and burning oil shale in pulverized furnaces, or bubbling fluidized beds. To improve the availability of oil shale, many specialists have advocated burning oil shale in a circulating fluidized bed (CFB), which has a satisfactory combustion efficiency, low NOx and SO{sub 2} emission, adaptability to low-grade coal, etc. In Huadian, China, a plant incorporating three units of 65 th{sup -1} oil shale-fired CFB began successful commercial operation in 1996, proving that burning oil shale in a CFB produces both high combustion efficiency and environmental protection. For effective utilization of oil shale, its pyrolysis and combustion characteristics, emission performance of gaseous pollutants from an oil shale-fired CFB pilot setup, co-combustion characteristics of oil shale and high sulfur coal as well as the operating ...
General trends of developing hydrogen power engineering and technology in Ukraine are considered. Based on a general level of power consumption and real opportunities for hydrogen production, a conclusion is derived that there are possibilities in the near future to partially replace conventional hydrocarbon fuels by hydrogen. Besides, developed technologies for burning hydrogenous gases and hydrogen-fuel systems when applied to transport installations allow one to improve essentially their power and ecological characteristics. 5 refs.
Using spectral hole-burning-based ultraslow group velocity in a dilute solid medium, we report enhanced photon echo efficiency three orders of magnitude higher than that in a nonslow light regime. The enhancement is due to exponentially increased absorption of an optical data pulse owing to the enhanced photon-atom interaction in an ultraslow light regime, whereas echo reabsorption is negligibly small due to group-velocity dependent population depletion.
As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.
"1"0"1Mo is an important radionuclide to determine the burn-up of nuclear fuels, but its half-life reference values had marked differences. It is described in detail the principles and processes of the position normalization method by two high purity germanium detectors to determinate the half-life of "1"0"1Mo. (authors)
The gamma scanning system which is installed in IMEF is the equipment obtaining the gamma ray spectrum from irradiated fuels. This equipment could afford the useful data relating spent fuels like as burn-up measurements. We describe the specifications of the equipment and its accessories, and also described its operation procedure so that an operator can use this report as the operation procedure. (author). 1 tab., 11 figs., 11 refs.
The theoretical evolution of a horizontal branch star of Population II is followed through the helium burning in the core phase and is compared with the results given by other investigators. The m- fluence of different physics and interpolation schemes in the opacity tables is discussed. Some thoughts are given on the explanation of the erratic period variations observed in some of the RR Lyrae variables in the globular clusters. (auth)
The report gives results of economic evaluations of three gypsum-producing flue gas desulfurization processes: advanced limestone (in-loop forced oxidation with adipic acid additive), Davy S-H (lime), and Dowa (aluminum sulfate, limestone). For a 500-MW power unit burning 3.5% su...
Economics may one day dictate that it makes sense to replace oil or natural gas with coal in boilers that were originally designed to burn oil or gas. In recognition of this future possibility, Pittsburgh Energy Technical Center (PETC) has supported a program led by ABB Power Plant Laboratories in cooperation with the Energy and Fuels Research Center of Penn State University to develop the High Efficiency Advanced Coal Combustor (HEACC). The objective of the program is to demonstrate the technical and economic feasibility of retrofitting a gas/oil designed boiler to burn micronized coal. In support of the overall objective the following specific areas were targeted: a coal handling/preparation system that can meet the technical requirements for retrofitting microfine coal on a boiler designed for burning oil or natural gas; maintaining boiler thermal performance in accordance with specifications when ...
This appendix contains the alphabetically indexed bibliography for the complete group of reports on municipal waste management alternatives. The references are listed for each of the following topics: mass burn technologies, RDF technologies, fluidized-bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting, and anaerobic digestion of MSW.
The removal of tritiated water vapour was tested by use of a small burning apparatus and a clinoptilolite filter. It was found that decontamination factor of about 10"4 could be obtained by a clinoptilolite filter. The adsorption of HTO in the clinoptilolite is caused by the diffusion, so it is necessary that filtration velocity is maintained below 0.01 m/sec. Decontamination factor was not influence by the moisture content of a clinoptilolite and tritiated water vapour once adsorbed on a filter was hardly removed. (auth.).
With the advance of science, rise of public interest in environmental matters, and continuing erosion of air quality, Federal and state regulators are demanding an increasing complex array of data concerning emissions produced by burning and detonating energetic materials. The US Department of Defense, one of the world`s largest consumers of energetic materials, now must characterize combustion products resulting from open burning/open detonation disposal operations. The catch-all phrase ``below detection limits`` no longer satisfies the regulators who now want testing to delve into the ppt level for volatile organic compounds and ppt level for semivolatile organic compounds. Regulators are also expanding their scope of interest and may soon be asking for emissions data on training operations such as artillery firing. Providing this type of information is no longer an impossibility. The Army, as the single manager of conventional munitions for ...
A coherent lidar system has been constructed for the measurement of alpha particles in a burning plasma. The lidar system consists of a pulsed CO{sub 2} laser transmitter and a heterodyne receiver. The receiver local oscillator is a cw, sequence-band CO{sub 2} laser operating with a 63.23 GHz offset from the transmitter.
In nuclear fuel with a burn-up of 33 kg/t U and 52 kg/t U 15 transuranium nuclides "2"3"7Np to "2"4"6Cm have been determined by alpha and gamma spectroscopy after radiochemical separation. (author).
British Nuclear Fuels (BNFL) is currently operating its third generation of nuclear plant for the management of irradiated nuclear fuel. Development for the fourth generation plant must meet requirements for processing higher burn-up fuel with lower unit costs, lower environmental impact, better process control, and more flexible control of actinides. .
Low temperature Nonphotochemical Hole Burning (NPHB) Spectroscopy of the dye rhodamine 800 (MF680) was applied for the purpose of discerning differences between cultured normal and carcinoma ovarian surface epithelial (OSE) cells. Both the cell lines were developed and characterized at the Mayo Clinic (Rochester, MN), with the normal cell line having been transfected with a strain of temperature sensitive Simian Virus 40 Large T Antigen (SV40) for the purpose of extending the life of the cell culture without inducing permanent changes in the characteristics of the cell line. The cationic lipophilic fluorophore rhodamine 800 preferentially locates in in situ mitochondria due to the high lipid composition of mitochondria and the generation of a large negative membrane potential (relative to the cellular cytoplasm) for oxidative phosphorylation. Results presented for NPHB of MF680 located in the cells show significant differences between the two cell lines. The ...
Low temperature Nonphotochemical Hole Burning (NPHB) Spectroscopy of the dye rhodamine 800 (MF680) was applied for the purpose of discerning differences between cultured normal and carcinoma ovarian surface epithelial (OSE) cells. Both the cell lines were developed and characterized at the Mayo Clinic (Rochester, MN), with the normal cell line having been transfected with a strain of temperature sensitive Simian Virus 40 Large T Antigen (SV40) for the purpose of extending the life of the cell culture without inducing permanent changes in the characteristics of the cell line. The cationic lipophilic fluorophore rhodamine 800 preferentially locates in in situ mitochondria due to the high lipid composition of mitochondria and the generation of a large negative membrane potential (relative to the cellular cytoplasm) for oxidative phosphorylation. Results presented for NPHB of MF680 located in the cells show significant differences between the two cell lines. The ...
Thermal and mechanical properties for geothermal formations are tabulated for a range of temperatures and stress conditions. Data was obtained from the technical literature and direct contacts with industry. Thermal properties include heat capacity, conductivity, and diffusivity. Undisturbed geothermal profiles are also presented. Mechanical properties include Youngs modulus and Poisson ratio. GEOTEMP thermal simulations of drilling, production and injection are reported for two geothermal regions, the hot dry rock area near Los Alamos and the East Mesa field in the Imperial Valley. Actual drilling, production, and injection histories are simulated. Results are documented in the form of printed GEOTEMP output and plots of temperatures versus depth, radius, and time. Discussion and interpretation of the results are presented for drilling and well completion design to determine: wellbore temperatures during drilling as a function of depth; bit temperatures over the ...
Nowadays the safety of Nuclear Power Plants is becoming more and more significant. Therefore consideration of severe accidents shall be included in both design and operating process of Nuclear Power Plants. In particular ground motion forms one of the important natural hazards. For structural analysis both linear-elastic and non-linear methods are specified by the engineering codes for earthquake resistance design. However, time history analysis is required for investigation of non-linear structural behaviour. Moreover, non-linearities are often caused by the presence of damage. This can be detected by means of structural health monitoring and subsequently system identification. In this paper the advantages of both dynamic time history analysis and damage detection by means of wavelet analysis are discussed. First, the non-linear behaviour of a frame structure due to an artificial earthquake motion is analyzed. A comparison to non-time ...
A sum-over-histories generalized quantum theory is developed for homogeneous minisuperspace type A Bianchi cosmological models, focusing on the particular example of the classically recollapsing Bianchi type-IX universe. The decoherence functional for such universes is exhibited. We show how the probabilities of decoherent sets of alternative, coarse-grained histories of these model universes can be calculated. We consider in particular the probabilities for classical evolution defined by a suitable coarse graining. For a restricted class of initial conditions and coarse grainings we exhibit the approximate decoherence of alternative histories in which the universe behaves classically and those in which it does not. For these situations we show that the probability is near unity for the universe to recontract classically if it expands classically. We also determine the relative probabilities of quasiclassical trajectories ...
T-history method, developed for measuring heat-of-fusion of phase change material (PCM) in sealed tubes, has the advantages of a simple experimental device and convenience with no sampling process. However, some improper assumptions in the original method, such as using a degree of supercooling as the end of latent heat period and neglecting sensible heat during phase change, can cause significant errors in determining the heat of fusion. We have improved this problem in order to predict better results. The present study shows that the modified T-history method is successfully applied to a variety of PCMs such as paraffin and lauric acid having no or a low degree of supercooling. Also it turned out that selected periods for sensible and latent heat do not significantly affect the accuracy of heat- of-fusion. As a result, the method can provide an appropriate means to assess a newly developed PCM by a cycle test even if a very accurate value ...
Recently, various types of allogeneic skin substitutes including cultured epidermal substitute (CES), cultured dermal substitute (CDS), and cultured skin substitute (CSS), which are composed of keratinocytes and/or fibroblasts as the cellular component(s), have been used as biological wound dressings. In our study, the allogeneic CDS was prepared by plating fibroblasts on a spongy collagen. The clinical evaluation was conducted using fresh or cryopreserved allogeneic CDS. In 145 of our clinical cases, 95% (138/145) of various wounds were evaluated as achieving good or excellent results, including 96% (22/23) of deep dermal burns (DDB) and dermal burns (DB), 100% (53/53) of partial-thickness donor wounds, 91% (21/23) of traumatic skin defects, 100% (5/5) of pressure ulcers, 82% (9/11) of chronic skin ulcers, 100% (6/6) of coverage for debrided DB, and 92% (22/24) of coverage for autologous meshed graft. The results obtained in our study suggest ...
Nanocomposites containing polyethylene (PE) and montmorillonite clay organically modified (OMMT) with quaternary ammonium salts were obtained via direct melt intercalation. A montmorillonite sample from the Brazilian state of Paraiba was treated with four different types of quaternary ammonium salts. After the treatment, the powder was characterized by X-ray diffraction and scanning electron microscopy. The dispersion and morphologies of OMMT within PE were investigated by X-ray diffraction and transmission electron microscopy. The results revealed the formation of intercalated montmorillonite layers in the PE matrix. The thermal stability and flammability of the PE/montmorillonite clay nanocomposites were measured by thermogravimetry and horizontal burning tests for HB classification, Underwrites Laboratories (UL 94), respectively. It was shown that the samples do not degrade at the processing temperature. By adding only 3 wt.% montmorillonite, the ...
The development of soil cover with capillary effect required laboratory experiments where diffusion was studied. The effective diffusion coefficients D of materials in the different layers were determined, as well as the reaction constants of reactive materials. Once soil cover is in place, its efficiency can be controlled by oxygen burn up trials in situ. In the specific case where the materials that comprise the soil cover consume oxygen, even in small quantities, the usual interpretation of these trials is not applicable. In this poster presentation, the authors proposed different procedures for long term trials, in situ and in the laboratory, as well as a new interpretation method based on the use of numerical solutions to the modified Fick equations of diffusion for reactive materials. Special emphasis is placed on the proper enunciation of the laws and the solutions appropriate in such situations. The authors illustrated the procedure using data acquired on a ...
In China, the conventional utilization of oil shale is concentrated mainly on retorting oil shale to produce shale oil and fuel gas, and burning oil shale to generate electricity. The growth of petroleum price, and the development in heavy industry, make these conventional utilization facilities become unavailable on the energy market. In this paper, a new comprehensive utilization system is recommended for the future use of Huadian oil shale, based on the current status of energy and the characteristics of oil shale. The system involves three subsystems: retort subsystem, where coarse oil shale (8-80 mm) is retorted to shale oil, hydrocarbon gases and oil shale semicoke; combustion subsystem, where the mixture fuel of oil-shale semicoke and fine oil shale (0-8 mm) is fed to a circulating fluidized bed (CFB) furnace to burn, in order to generate high-pressure steam which is used to supply heat and generate electricity via a traditional ...
The research and development for the first year of the project are performed through specialization of researchers, information from aborad and international cooperation, securement of advanced nuclear technology, development and installation of test equipment, application of external man-power, establishment of advanced test techniques, and certified test method. 1. Absolute efficiency measurement examination technology development of gamma scanning system 2. Sample preparation technology development of SEM and EPMA for micro-structural observation and chemical composition analysis 3. Irradiated high burn-up nuclear fuel transportation and test for PWR 4. Development of hot cell examination techniques and equipment 5. Acquirement of KOLAS system. In addition to the project, the following activities are carried out as follows; - PIE of Hanaro fuel(KH99H-001) - PIE of U-Mo advanced nuclear fuel irradiated at Hanaro - PIE of Hi-MET advanced nuclear fuel irradiated at ...
In this study, the effects of hydrogen peroxide on laminar, premixed, methane-air flames at atmospheric pressure and temperature were investigated using CHEMKIN III and GRI 3.5 mechanism. The range of fuel/air equivalence ratio {phi} was varied from 0.6 to 1.2, and the amount of hydrogen peroxide was altered from 0% to 20% volumetric fraction of the methane-hydrogen peroxide (air excluded) mixture. The burning velocity was found to increase with increasing hydrogen peroxide addition, with a relatively larger increase for the fuel-richer mixtures ({delta}S{sub u} up to 15 cm/s for {phi} {approx}=1.2). The adiabatic flame temperature rose with hydrogen peroxide addition, and the temperature rise per unit hydrogen peroxide addition was more significant ({delta}T up to 100 K) for the leaner mixtures. For the same mixture stoichiometry, adding hydrogen peroxide also increased CO concentration and NO{sub x} emissions somewhat. Accordingly, the benefits of adding hydrogen ...
One bundle of Hanaro fuel irradiated up to 50%-burnup and cooled for 6 months was transported to IMEF for PIE, which has 6 elements. At first we measured the longitudinal distribution and the rotational distribution of several dominant peaks intensities from the bundle. After dismantling of the bundle we measured the longitudinal distribution of {sup 137}Cs and {sup 134}Cs peaks in each fuel element to see the burn-up feature. And finally we found out the relative number distribution of {sup 137}Cs and {sup 134}Cs for each detection point, which would be used for burn-up calculation. The relative detection efficiency of the scanning system was obtained experimentally by using the {sup 134}Cs peaks. We also checked up the azimuthal difference of peak intensity for each element, which are resulted about 2% of difference. These data will be used for the further analysis of Hanaro fuel performance evaluation. (author)
Historically, the bulk production of electricity has been achieved by burning fossil fuels, with unavoidable gaseous emissions, including large quantities of carbon dioxide: an average-sized modern coal-burning power station is responsible for more than 10 Mt of CO{sub 2} each year. This paper details typical emissions from present-day power stations and discusses the options for their reduction. Acknowledging that the cuts achieved in the past decade in the UK CO{sub 2} emissions have been achieved largely by fuel switching, the remaining possibilities offered by this method are discussed. Switching to less-polluting fossil fuels will achieve some measure of reduction, but the basic problem of CO{sub 2} emissions continues. Of the alternatives to fossil fuels, only nuclear power represents a zero-carbon large-scale energy source. Unfortunately, public concerns over safety and radioactive waste have still to be assuaged. Other approaches ...
In order to investigate the effect of humidity on laminar burning velocity(S), the effect of humidity on the combustion reaction and radiation intensity was studied, taking account of dilution gases such as CO/sub 2/ and Ar which has the approximately identical characteristics to exhaust gas circulation(EGR) gas used to prevent NOx discharge from engines. According to the heat reaction theory, mean specific heat(C) of mixture, mean molecular weight(M) and adiabatic flame temperature(T) etc. were said to affect S but from experimental results, the effect of M and C could be ignored, compared with the effect of T. The relationship between S and H/sub 2/O, Ar of CO/sub 2/% in mixture of diluted gases was clarified. The effect of H/sub 2/O on S was mainly caused by changes of T. The effect of radical C/sub 2/, CH and OH on radiation intensity was similar to that of H/sub 2/O and Ar and the effect of H/sub 2/O on combustion was found only to be the physical effect. (10 ...
In nuclear fuel, in approximately one quarter of the fissions, one of the two formed fission products is gaseous. These are mainly the noble gases xenon and krypton with isotopes of xenon contributing up to 90% of the product gases. These noble fission gases do not combine with other species, and have a low solubility in the normally used uranium oxide matrix. They can be dissolved in the fuel matrix or precipitate in nanometer-sized bubbles within the fuel grain, in micrometer-sized bubbles at the grain boundaries, and a fraction also precipitates in fuel pores, coming from fuel fabrication. A fraction of the gas can also be released into the plenum of the fuel rod. With increasing fission, and therefore burn-up, the ceramic fuel material experiences a transformation of its structure in the 'cooler' rim region of the fuel. A subdivision occurs of the original fuel grains of few microns size into thousands of small grains of sub-micron sizes. ...
Fischer-Tropsch (F-T) diesel fuel is characterized by a high cetane number, a near-zero sulphur content and a very low aromatic level. On the basis of the recorded incylinder pressures and injector needle lifts, the combustion characteristics of an unmodified single-cylinder direct-injection diesel engine operating on F-T diesel fuel are analyzed and compared with those of conventional diesel fuel operation. The results show that F-T diesel fuel exhibits a slightly longer injection delay and injection duration, an average of 18.7% shorter ignition delay, and a comparable total combustion duration when compared to those of conventional diesel fuel. Meanwhile, F-T diesel fuel displays an average of 26.8% lower peak value of premixed burning rate and a higher peak value of diffusive burning rate. In addition, the F-T diesel engine has a slightly lower peak combustion pressure, a far lower rate of pressure rise, and a lower mechanical load and ...
The Coal Quality Engineering Analysis (CQEA) program developed by the New York State Electric and Gas Company (NYSEC) calculates the as-burned cost of burning a specific coal in a specific generation unit. These costs include: maintenance costs for coal and ash handling equipment; ash disposal costs; cost of oil (if required for flame stability and/or derating because of pulverizer capacity limitation); flue gas desulfurization costs; cost of replacement power caused by pulverizer, precipitator fly ash collection and bottom ash capacity limitation; boiler losses due to moisture, hydrogen, dry gas and unburned carbon; power for coal and ash handling equipment; power for coal pulverizers; cost of using excess air to prevent slagging of coal with low ash softening temperatures; and effect of heat rate on coal tonnage required for a desired generation. The use of CQEA to identify areas in which plant operations may be improved is discussed. 7 ...
Combustion scientists are primarily concerned with the fuels most often burned as energy sources (coal, petroleum products, and natural gas), with the goal of learning to burn them as efficiently, intensely, and cleanly as possible. Discovering those slight rearrangements of chemical bonds that together account for the net chemical transformation is the key to understanding how combustion proceeds. Once these reactions have been defined, the chemist can determine the rate coefficient of each reaction as a function of temperature and assemble the information into flame models. The computer programs that use these models to predict experimental results combine two sets of equations describing (1) the diffusive and reactive rates of change in concentration of all the molecules in the flame and (2) the flow of the reacting gases. Although the details of hydrocarbon-flame models are still disputed, many of their general features are clear and the ...
Heat production in biological materials due to absorption of radiowaves and microwaves can be used in applications as diverse as cancer treatment and cooking. However, the hazards of overexposure range from hyperthermia to cataracts and internal burns. To maximize the clinical benefits and minimize potential hazards, the biological effects of radiowaves and microwaves must be understood. Dielectric measurements can be used to determine the extent of such effects in various applications and at various levels of exposure. The values of maximum permissible exposure levels that are likely to be recommended aeat production in biological materials due to absorption of radiowaves and microwaves can be used in applications as diverse as cancer treatment and cooking. However, the hazards of overexposure range from hyperthermia to cataracts and internal burns. To maximize the clinical benefits and minimize potential hazards, the biological effects of ...
In this paper a computational analysis of 11 fuel samples (seven UO_2 and four MOX) with a burn-up ranging from 20 MWd/kgHM up to 121 MWd/kgHM (HM: Heavy Metal) is carried out with the depletion module of the lattice code CASMO-4E [Rhod01, Rhod01b] using the neutron data libraries ENDF/B-VI and JEF-2.2 and a pin cell model. In order to assess the accuracy of the model and the depletion calculation in the determination of the isotopic inventory after several irradiation cycles, the calculated results were compared to experimental data gathered from a chemical isotopic analysis of the fuel samples performed at the Hot Laboratory at the Paul Scherrer Institut (PSI), Switzerland. Selected results of this comparison, which includes 54 isotopes (17 actinides and 37 fission products), are presented here. (orig.)
This report presents the results of Run 261 performed at the Advanced Coal Liquefaction R & D Facility in Wilsonville, Alabama. The run started on January 12, 1991 and continued until May 31, 1991, operating in the Close-Coupled Integrated Two-Stage Liquefaction mode processing Illinois No. 6 seam bituminous coal (from Burning star No. 2 mine). In the first part of Run 261, a new bimodal catalyst, EXP-AO-60, was tested for its performance and attrition characteristics in the catalytic/catalytic mode of the CC-ITSL process. The main objective of this part of the run was to obtain good process performance in the low/high temperature mode of operation along with well-defined distillation product end boiling points. In the second part of Run 261, Criterion (Shell) 324 catalyst was tested. The objective of this test was to evaluate the operational stability and catalyst and process performance while processing the high ash Illinois No. 6 coal. Increasing viscosity ...
Early technical history of electric supply to electric railways is briefly reviewed as an introduction to the following seven papers included in this special issue on technologies for saving energy in railway operation. Continuous power supply played a significant role in the early history of railway technologies. The variable voltage variable frequency (VVVF) power electronic technology had also a substantial impact on railway traction systems after 1980s. VVVF technology made it possible to have more efficient drives, downsize rolling stocks, and develop regenerative brakes. Because detailed discussions on each technical development are presented in the following papers, the general remarks of those technologies made in this introduction provide logical links to the ideas presented in th...
Sustainable development of geothermal resources is the key to prolong the commercial life of geothermal fields. This paper uses two well-known geothermal fields in China, with long histories of production, to demonstrate how sustainability can be quantitatively evaluated, and to highlight the essential differences between sustainable and non-sustainable development schemes. After examining the complex nature of sustainability evaluation, fuzzy synthetic evaluation is applied as a tool for the quantitative sustainability rating of geothermal reservoirs. The evaluation procedures include systemic criteria selection, weighing, individual criterion evaluation and finally final multi-criterion decision analysis evaluation. The sustainability of a limestone reservoir in the urban sector of Tianj...
This paper addresses the unique structural requirements for successful conversion of tankers for floating production storage and offloading (FPSO) or floating storage and offloading (FSO) service. A description is given of the steps undertaken during two recent and very different conversions of a highly optimized 1980s VLCC to FPSO service, and a typical robust 1970s ULCC to FSO service. The paper describes the steps needed for ensuring the FPSO or FSO requirements are successfully met during conversion of the two tankers - each having its own history, e.g. date of build, original design, material choices, class society, voyage history and repairs. Firstly, the paper describes the procedure and results of an early initial structural assessment procedure on the basis of an American Bureau o...
Results that contradict known physics, data manipulated, lack of vigilance by co-authors, failures in the system for scientific publication... Last September a US Committee of Enquiry unveiled one of the most serious frauds in the history of physics. Over a two year period, a young researcher at Bell Laboratories had published a large number of articles with exciting results for solid state physics, but which, alas, were fraudulent! Obviously a fraud of this magnitude is exceptional. However, it did serve to focus attention on the problem of integrity and honesty in research practices. This subject, crucial to the well-being and credibility of scientific research, will be the central theme of the lecture given by Nicholas Steneck, Professor of History at the University of Michigan. A leading expert on this issue, on which he has published extensively, he is a consultant to the Office of Research Integrity in the US, and has been closely ...
The term Process Systems Engineering (PSE) is relatively recent. It was coined about 50 years ago at the outset of the modern era of computer-aided engineering. However, the engineering of processing systems is almost as old as the beginning of the chemical industry, around the first half of the 19th century. Initially, the practice of PSE was qualitative and informal, but as time went on it was formalized in progressively increasing degrees. Today, it is solidly founded on engineering sciences and an array of systems-theoretical methodologies and computer-aided tools. This paper is not a review of the theoretical and methodological contributions by various researchers in the area of PSE. Its primary objective is to provide an overview of the history of PSE, i.e. its origin and evolution; ...
The history of the technical, economic, and financial performances of these four countries' power companies over the past two decades is recounted, and then interpreted as the result of the existing organizational models. The changes that have occurred can be understood in long-term perspective by comparing the performance of these companies to the characteristics, rules, and objectives used to define the models, which also helps explain the history of performance indicator variations. Two models are defined: one for the physical plant and one for the management. These correspond to two successive phases in the organization and operation of the electrical sector. Rural electrification and regional interconnection will be important factors in any new model or models developed for the future, because the forms they take is likely to modify the characteristics of these national power companies. 26 refs., 1 fig., 3 tabs.
This paper presents a numerical study on the formation history of coalbed methane (CBM) reservoir in the southeast edge of Ordos Basin, China. The coal seams studied belong to the Late Palaeozoic coal-bearing series. These coal seams have a burial history and experienced the process of subsidence, rapid subsidence alternated with uplift and then uplift, sequentially, and underwent the geothermal actions at normal, extremely high, and then normal temperatures, respectively. Coal organic matter of the coal seams matured in the Triassic Period and in the Late Jurassic to Early Cretaceous Period. The results from numerical simulation reveal that CBM reservoir evolution history can be classified into five stages, namely primary, initial, stagnant, active and dissipative stages. In the first (primary) stage, coal rank was very low and there was little methane generated and stored in the coal seams. In the second (initial) stage, ...
Purpose - This paper seeks to deal with the history of Research and Development (R&D) management. It takes the history of the R&D Department of the Royal Philips Electronics of The Netherlands as an example to unravel the dynamics behind industrial R&D management. Design/methodology/approach - This paper is based upon historical and theoretical studies on industrial R&D institutions and research cultures. Findings - The paper proposes that the directors of the Philips R&D Department continually shaped and reshaped the organization in order to retain researchers with creative ideas, and to stimulate innovativeness. The R&D-management was the outcome of a search process that comprehended a mixture of scientific and industrial (management) skills, knowledge and experti...
The site characterization of Yucca Mountain, NV as a potential high level nuclear waste repository includes study of the surficial deposits as a record of the paleoenvironmental history of the Yucca Mountain region. An important aspect of this history is an understanding of the evolution of paleogeography leading to establishment of the present drainage pattern. Establishment of drainage basin evolution is needed before geomorphic response to paleoclimate and tectonics can be assessed, because a major change in drainage basin geometry can predominantly affect the sedimentary record. Because alluvial aquifers are significant to regional hydrology, a major change in surface drainage resulting in buried alluvium could have hydrogeologic significance. In this paper, we report on geologic evidence for a major modification in surface drainage pattern in the Yucca Mountain region, resulting in the probable establishment of the Fortymile Wash drainage ...
The authors determined migration timing and abundance of juvenile spring chinook salmon Oncorhynchus tshawytscha and juvenile steelhead/rainbow trout O. mykiss from three populations in the Grande Ronde River basin. Based on migration timing and abundance, two distinct life-history strategies of juvenile spring chinook and O.mykiss could be distinguished. An early migrant group left upper rearing areas from July through January with a peak in the fall. A late migrant group descended from upper rearing areas from February through June with a peak in the spring.
Inverse and direct methods have been used to analyze a large number of borehole temperature logs in order to infer past climatic changes. Results indicate a warming of 1-2[degree]C in eastern and central Canada during the past 150 years. A period of cooling between 500 and 200 years before present, corresponding to the time of the Little Ice Age, has also been identified in the same areas. A regional ground temperature history is estimated for eastern and central Canada from the simultaneous inversion of several temperature logs. The inferred temperature changes appear correlated with the concentration of atmospheric carbon dioxide as reported from a Greenland ice core, and agree with existing meteorological and dendrochronological records for the area.
Objectives Our purpose was to evaluate interaction of green tea consumption and abdominal obesity as related factors for lacunar infarction in Korean women. Designs A hospital-based, incident case-control study. Settings The Prevention and Managements of Stroke in Women study. Participants Cases (n=233) of first incident lacunar infarction were enrolled and matched by age to stroke-free hospital controls (n=204). Measurements The data were collected through face-to-face interviews by well trained research assistants to assess demographic, medical, lifestyle, marital status, religions status, green tea consumptions, family history of stroke, smoking status, alcohol consumption, meat and vegetable intake frequency, and past history of hypertension. Biochemical analysis, fasting blood specime...
Understanding Center for Medicare and Medicaid Services (CMS) documentation and coding rules is challenging for most physicians. To accurately bill for clinical services, physicians must learn a system that may initially seem daunting, but is in fact governed by a small number of straightforward rules. The Evaluation and Management (E/M) guidelines for all service codes specify 3 components: history, examination, and medical decision-making, each with a defined set of elements or characteristics. Service coding is based on the level of care supported by the number of history and examination elements and the complexity of decision-making. This article will clarify the guidelines for outpatient clinical services and suggest a practical method of selecting appropriate E/M codes. Because physicians must often choose between billing codes 99213 and 99214 for a visit by an established patient, it will particularly focus on the minimum documentation ...
The Plutonium-Uranium Extraction (PUREX) Plant, conceived during the early Cold War years, was a vehicle to increase significantly US nuclear weapons production capacity. The original PUREX Plant was a concrete rectangle 1,005 feet long and 61.5 feet wide. The shielding capacity of the concrete was designed so that personnel in non-regulated service areas would not receive radiation in excess of 0.1 millirem per hour. This report discusses the design of the PUREX Plant, the production chronology, projects and equipment changes, equipment decontamination and reuse, waste management, and contamination events that have occurred during the operation of the plant. Additionally, the development and history of the Uranium Trioxide Plant are also covered.
'If you wish to foresee the future of mathematics our proper course is to study the history and present condition of the science.' Henri Poincare 'It is India that gave us the ingenious method of expressing all numbers by ten symbols, each symbol receiving a value of position, as well as an absolute value. We shall appreciate the grandeur of the achievement when we remember that it escaped the genius of Archimedes and Apollonius.' P.S. Laplace 'The Greeks were the first mathematicians who are still 'real' to us today. Oriental mathematics may be an interesting curiosity, but Greek mathematics is the real thing. The Greek first spoke of a language which modern mathematicians can understand.' G.H. Hardy This article deals with a short history of mathematics and mathematical scientists during...
The results of experimental studies on the contribution of zoogenic debris to transformation of soil properties in the southern taiga subzone of Central Siberia are analyzed. They show that water-soluble carbon outflow from the forest litter increases by 21-26% upon a Siberian moth invasion, with this value decreasing to 14% one year later. The burning of forest in an area completely defoliated by the pest leads to changes in the stock, fractional composition, actual acidity, and ash element contents of the litter. The litter-dwelling invertebrate assemblage is almost completely destroyed by fire and begins to recover only after two years. PMID:18491565
A report is given of investigations into the possibility of utilizing red mud from the Bayer process for producing Ferrari cements. On repeated burning at 1450deg C suitable mixtures of red mud with silica and lime form a clinker with a low free lime content from which Ferrari cement can be produced. The average 28-day compressive strengths of cements produced from this clinker are so encouraging that further investigations are appropriate. (orig.).
If trends from the past continue into the future, the major increase in the use of energy will come from the developing nations. If the industrialization of the Third World continues to be based on the burning of fossil fuels, the impact on the global climate from these sources alone will be substantial. Statistical information supporting the above statements is presented. The conclusion is reached that improving the efficiency of energy use is not sufficient to avert climatic changes. The accelerated and worldwide use of nuclear power is essential and, if prudently used, can become, contrary to the recommendations of the Brundtland Commission, the basic energy source fuelling future sustainable developments of the world. (author).
Closure of nuclear fuel cycle is considered as a way to reduce the hazards of nuclear power industry waste. The potential and prospects of different technologies and installations including ADTT in solving this problem are discussed. A new relative criterion is proposed to assess the dangers of the waste. Equilibrium mode approximation is used in the estimates. It is shown that irretrievable losses of actinides do not depend on relative intensity of burning. Neutron economy of accelerator-driven blankets is considered and an expression is derived for transmutation value of 'external' neutrons. 8 refs., 2 tabs.
Air pollution constraints continue to intensify, resulting in solid waste volume increases. An example of this is coal burning power plant flue gas desulfurization by scrubbing. The aqueous suspensions of calcium sulfate hemihydrate or calcium sulfate dihydrate will exceed 200 million tons annually by the year 2000. Disposal of these wastes can have massive environmental effects, due to physical instability and leaching to groundwater. One alternate disposal technique is sulfopozzolanic fixation, converting the FGD waste by addition of fine coal ash and an alkaline earth additive, into a monolithic mass. 6 refs., 17 figs., 3 tabs.
Novel lightweight bricks have been produced by sintering mixes of dried water treatment sludge and rice husk. Samples containing up to 20 wt.% rice husk have been fired using a heating schedule that allowed effective organic burn-out. Rice husk addition increased the porosity of sintered samples and higher sintering temperatures increased compressive strengths. Materials containing 15 wt.% rice husk that were sintered at 1100 degrees C produced low bulk density and relatively high strength materials that were compliant with relevant Taiwan standards for use as lightweight bricks. PMID:19596512
Many rural industries generate amounts of biomass waste, such as rice husks, sawdust, wood chips, nutshells and plant stalks that represent a substantial energy resource. However, most often these biomass wastes are not utilized and are dumped or burned in the open. This paper will show the whole project cycle of an installation and commissioning of a thermal configuration of a BG-Systems in Indonesia. These projects highlight the economic, operational and environmental benefits of the BG-Systems. BG-Systems are small fixed-bed downdraft gasifier systems being marketed by BG Technologies that convert biomass into a producer gas that is essentially free of tars and can be used reliably in a diesel engine or thermal combustor. (author)
Actinides other than the main uranium or plutonium isotopes take a growing part in the different stages of the nuclear cycle. For the French nuclear power program based on the development of light water reactors and fast breeders, many evaluations of the secondary actinides build up are made for the both reactor types using mainly the existing reactor codes. The comparison of these foreseen compositions with experimental results allows to perform some adjustments of the neutronic data. The secondary actinide compositions are given for some typical fuels and their consequences on the nuclear cycle are discussed. An hypothetical burning of these wastes in fast reactors has been studied and the main conclusions are reported.
Experimental investigation of the length of single burning jets of methane and hydrogen previously diluted with an inert gas (nitrogen or helium) was carried out. Efflux of fuel gases into the atmosphere occurred through cylindrical extension pieces 4 and 8 mm in diameter. The Reynolds numbers at the cut of a piece varied in the range from 400 to 12,000. A clearly defined dependence of the jet length on the quality of the added inert gas is obtained. The correlation of experimental data made it possible to recommend formulas for engineering calculations of free laminar and turbulent jets.
The components with masses 32 and 64M _s_u_n, evolved with the matter mixing in the semiconvective zone and filling their Roche lobes, after the main-sequence evolution overflow their Roche lobes and lose matter during the first part of the helium core burning. After the overflow end, the components lose the matter by stellar wind. The components shrink in the nuclear timescale. At first, they have the blue supergiant character with anomalous CNO abundance, then - the Wolf-Rayet stars character.
Nucleosynthesis and energy production in stellar environments depend critically on nuclear reaction cross sections. Reactions induced by alpha particles are important in the helium burning stage of stars, novae, and supernovae events. They involve light to medium weight nuclei up to about Z=32, and center-of-mass energies up to about 20 MeV. We are working on a project to compile and evaluate cross section data for alpha-induced reactions. These data will eventually be used to derive #alpha#-nucleus potential parameters. (author)
Beta-decay studies of the new neutron-rich isotopes sup(58,59)Cr, "6"3Mn, sup(66,67)Co and "6"9Ni, yielding distinctly shorter half-lives than the corresponding theoretical predictions, are presented. The influence of the short half-lives on the r-process calculations of nuclear abundances is discussed. It is concluded that a significantly higher neutron density than the one obtained from explosive helium burning in supernovae is needed to reproduce the observed abundances around A = 80. (orig.).
Fuel irradiation leads to a swelling resulting from the formation of gaseous (Kr, Xe) or solid fission products which are found either in solution or as solid inclusions in the matrix. This phenomena has to be evaluated to be taken into account in fuel cladding Interaction. Fuel swelling was studied as a function of burn up by measuring the corresponding cell constant evolution by X-Ray diffraction. This study was realized on Mixed Oxide Fuels (MOX) irradiated in a Pressurized Water Reactor (PWR) at different burn-up for 3 initial Pu contents. Lattice parameter evolutions were followed as a function of burn-up for the irradiated fuel with and without an annealing thermal treatment. These experimental evolutions are compared to the theoretical evolutions calculated from the hard sphere model, using the fission product concentrations determined by the APPOLO computer code. Contribution of varying parameters influencing the ...
Plutonium and minor actinides produced as by-products of the UO_2 nuclear cycle could be considered as waste or energy source depending on the strategy selected in the nuclear energy programme. Considering Pu and Minor Actinides as a source, they can be burned in existing water reactor for diminishing the radiotoxicity of the spent fuel, it is necessary to use 'inactive' materials as matrix like ThO_2. ThO_2 matrix has demonstrated its Pu burning efficiency and higher corrosion resistance than UO_2. Uranium-plutonium mixed oxide (MOX) fuel efficiency is low because the presence of U in MOX results in the creation of some new Pu under irradiation. The dissolution behaviour of irradiated (Th,Pu)O_2 pellets with burn-up of 38.8 MWd/kg Th has been studied in carbonated (20 mM HCO_3"-), deionised and granite ground water solution in a hot cell. The dissolution behaviour of Th, Pu, U and Np was studied in order to find out ...
This thesis contains the candidate's original work on excitonic structure and energy transfer dynamics of two bacterial antenna complexes as studied using spectral hole-burning spectroscopy. The general introduction is divided into two chapters (1 and 2). Chapter 1 provides background material on photosynthesis and bacterial antenna complexes with emphasis on the two bacterial antenna systems related to the thesis research. Chapter 2 reviews the underlying principles and mechanism of persistent nonphotochemical hole-burning (NPHB) spectroscopy. Relevant energy transfer theories are also discussed. Chapters 3 and 4 are papers by the candidate that have been published. Chapter 3 describes the application of NPHB spectroscopy to the Fenna-Matthews-Olson (FMO) complex from the green sulfur bacterium Prosthecochloris aestuarii; emphasis is on determination of the low energy vibrational structure that is important for understanding the ...
The effect of liquefied natural gas on pollutant emissions was evaluated experimentally with used and new appliances in the laboratory and with appliances installed in residences, targeting information gaps from previous studies. Burner selection targeted available technologies that are projected to comprise the majority of installed appliances over the next decade. Experiments were conducted on 13 cooktop sets, 12 ovens, 5 broiler burners, 5 storage water heaters, 4 forced air furnaces, 1 wall furnace, and 6 tankless water heaters. Air-free concentrations and fuel-based emission factors were determined for carbon monoxide, nitrogen oxides, nitrogen dioxide, and the number of (predominantly ultrafine) particles over complete burns?including transient effects (device warm-up and intermittent firing of burners) following ignition--and during more stable end-of-burn conditions. Formaldehyde was measured over multi-burn cycles. ...
The main purposes of this research was to investigate the feasibility of incineration of wool-scouring sludge in a novel vertical-axis-rotating fluidised bed (RFB). The experiment was carried out in a RFB with an internal diameter (ID) of 200 mm and height of 50 mm. A cold test was first conducted to investigate the fluidization performance of the RFB via parameters such as the bubbling, gas distribution, bed shape and pressure drop. The tumbling phenomena was observed in the bed, and this effectively enhanced the axial mixing. The appropriate range of bed thickness, rotating speed and sand particle size were identified to ensure the full fluidization and reduce the particle elutriation. Four wool-scouring sludges from different processes were incinerated in the RFB. With 5% support methane, all sludges with a maximum moisture up to 70% as received could be successfully burned in the RFB at rotating speeds of 200 and 300 rpm. The combustion was found to be intense ...
A detailed experimental investigation of the application of fractal geometry concepts in determining the turbulent burning velocity in the wrinkled flame regime of turbulent premixed combustion was conducted. The fractal dimension and cutoff scales were determined for six different turbulent flames in the wrinkled flame regime, where the turbulence intensity, turbulent length scale, and equivalence ratio were varied. Unlike previous reports, it has proved possible to obtain the fractal dimension and inner and outer cutoffs from individual flame images. From this individual data, the pdf distributions of all three fractal parameters, along with the distribution of the predicted increase in surface area, may be determined. The analysis of over 300 flame images for each flame condition provided a sufficient sample size to accurately define the pdf distributions and their means. However, the predicted S{sub T}/S{sub L}, calculated using fractal parameters, was ...
In this investigation natural gas has been used as an alternative fuel in diesel engines. Experiments have been performed to study the performance of the dual fuel engine with different diesel quantities as pilot injection. It was suggested in this research that combustion in the dual fuel engine occurred in four stages: the delay period, the slow stage of combustion, the rapid stage of combustion and the fourth stage of combustion. Because of the slower flame speed of natural gas and also because of the prolonged delay period, the combustion of the gas-air continued well into the expansion stroke. These resulted in lower efficiency and higher brake specific fuel consumption, and also higher exhaust gas temperature and higher carbon monoxide in the exhaust when the engine ran on dual fuel. The carbon dioxide and black smoke in the exhaust decreased as the gas was introduced in the engine. The ratio of alternative to diesel fuel was varied at the same load also at different load ...
In order to serve for efficient energy utilization and environmental improvement in the Republic of Vietnam, a 'Model project to reduce electric power consumption at cement burning plant' has been implemented. This paper summarizes the achievements. This project is intended to add an advanced, matured and reliable electric power generation facility using cement waste heat to the existing cement plant in Vietnam to produce steam and generate power by utilizing the waste heat generated from the preheating process in the burning plant. The present project has performed the detailed designing on the piping, electric facilities and instrumentation based on the basic agreement on the project. Fabrication of the piping has been executed by the Vietnam side. Valves and electric devices were procured and transported, including those fabricated in the previous fiscal year. Technology guiding personnel were sent for unpacking inspection, ...
Each WG has two Co-Chairs and six Vice-Chairs, except WG III, which for the Fifth ...Assessment cycle has three Co-Chairs.The Co-Chairs guide the WGs in fulfilling their ...IN THIS ISSUE A Brief History of the IPCC 1 IPCC-31 Report 3 Approval of the Draft Report of
The waste monitoring system in use at Los Alamos National Laboratory`s Plutonium Facility, TA-55, is a computer-based system that proves real-time information on industrial effluents. Remote computers monitor discharge events and data moves from one system to another via a local area network. This report describes the history, system design, summary, instrumentation list, displays, trending screens, and layout of the waste monitoring system.
This report documents a case history in which a cadaver and the associated burial objects were found well preserved after being buried for more than 2100 years in Southern China. The preservation is attributed to a layer of kaolin that surrounded the coffin and served as a barrier to water and air movement. The implications for the disposal of nuclear fuel waste are discussed.
The Montreal Protocol provides the international community with an effective equitable and dynamic mechanism for protecting the ozone layer. The paper uses the Protocol's negotiating history to describe how and why agreement on a particular issue was reached and provides an in-depth analysis of the Protocol's most innovative provisions. The paper discusses international implementation of the Protocol. It concludes with a brief description of recent developments leading up to the Protocol's possible modification in June 1990. (14 refs.).
The staff of the Southwest Technology Development Institute (SWTDI), in conjunction with the staff of Industrial Solar Technology (IST), have analyzed the performance, operation, and maintenance of a large solar process heat system in use at the 5,000 inmate California Correctional Institution (CCI) in Tehachapi, CA. This report summarizes the key design features of the solar plant, its construction and maintenance histories through the end of 1991, and the performance data collected at the plant by a dedicated on-site data acquisition system (DAS).
Scientists often re-invent things that were long known. Here we review these activities as related to the mechanism of producing power law distributions, originally proposed in 1922 by Yule to explain experimental data on the sizes of biological genera, collected by Willis. We also review the history of re-invention of closely related branching processes, random graphs and coagulation models.
In this study, a probabilistic seismic risk analysis of the Wolsung NPP containment building was performed by a seismic hazard analysis and a seismic fragility analysis based on the nonlinear dynamic time-history analyses. The conventional seismic fragility analysis of the safety related structures in a NPP have been performed by using the linear elastic analysis results. The probabilistic seismic risk of the containment building was 5.19e-8.
In this study, a probabilistic seismic risk analysis of the Wolsung NPP containment building was performed by a seismic hazard analysis and a seismic fragility analysis based on the nonlinear dynamic time-history analyses. The conventional seismic fragility analysis of the safety related structures in a NPP have been performed by using the linear elastic analysis results. The probabilistic seismic risk of the containment building was 5.19e-8.
Three existing organizational types that meet the decentralization criteria of local consumer ownership and control - cooperatives, Rural Electric Cooperatives, and municipal utilities - are examined. These three organizational precedents are analyzed in terms of their histories, structures, legal powers, sources of capital, and social and political aspects. Examples of related experiments with renewable energy technologies are given, and inferences are drawn regarding the organizations' suitability as vehicles for future implementation of decentralized renewable energy systems.
A polarized proton physics run took place during January, 1988, at the Brookhaven AGS. It is the purpose of this paper to review the tune-up period preceding that run. This was the third such run at the AGS; the others occurred in June of 1984 and February of 1986. Some comparisons will be drawn among these. A thorough review of the history and hardware associated with the acceleration of polarized protons at the AGS can be found in the proceedings of the last meeting of this group at Protvino and will not be repeated here. 2 refs., 6 figs., 1 tab.
... Quenching is one of the most fundamentally complex processes in the heat treatment of metals, and it is something on which mechanical properties and distortion of engineering components depend. AU$236.36 ex-GST Terms and Conditions Eyes on the Skies: 400... Adopted as the official book of the International Year of Astronomy (IYA) 2009, this stunningly illustrated history of telescopic discovery spans the range ...
This document provides structural load requirements and their basis for maintaining the structural integrity of the Hanford Single-Shell Tanks during waste feed delivery and retrieval activities. The requirements are based on a review of previous requirements and their basis documents as well as load histories with particular emphasis on the proposed lead transfer feed tanks for the privatized vitrification plant.
Jan 16, 2008 ... home town, and awards, as well as the ground personnel. .... I was also awarded six air medals, which were given based on the number of missions ..... We took these projects from birth to grave. .... Japanese sonar on their submarine. About that time another airplane dropped a bomb ...
Potential strategic missions for laser weapons, particularly those involving space-based lasers, are discussed. The functions of space-based lasers and the history of their conceptual development are summarized, and the problems of implementing such systems, including the building of a suitable laser and power source, and resolving the problem of optics, are discussed. Ongoing development programs are described, and the contrasting views of the necessity and usefulness of strategic laser systems are set forth.
Accounts are given of the history of coal liquefaction research and projects (indirect liquefaction, direct liquefaction, plus the recent state of Japanese developments and of process development), and of the significance of the petroleum age, the energy crisis and of coal liquefaction itself. (10 refs.) (In Japanese)
The history of the Czech Institute of Plasma Physics is highlighted. The article is structured as follows: Cyclic accelerators; Interaction of an external high-frequency field and high-temperature plasma - the tokamak; Interaction of an external high-frequency field and high-temperature plasma - pulse plasma systems; Low-temperature plasma - plasma technologies and new materials; Laser plasma - PALS; Optical diagnosis; and Teaching, conferences and international cooperation. (P.A.)
For most of the history of binary star astronomy, systems have been classified largely on the basis of how they were discovered and qualitative appearance of their spectra and light curves. Present understanding of single and double star evolution has now progressed to the point where most of the classes previously identified, and some new ones, can be arranged into evolutionary sequences, depending primarily on the initial masses and separation of the component stars.
This report describes the 2005 version of the Fluka particle transport code. The first part introduces the basic notions, describes the modular structure of the system, and contains an installation and beginner's guide. The second part complements this initial information with details about the various components of Fluka and how to use them. It concludes with a detailed history and bibliography.
The history of explosives vapor detection includes almost every detection strategy known to man. Initial attempts to utilize these techniques were dismal failures. However, with the development of the Electron Capture Detector (ECD), the first promising detection of explosives vapors became possible. The present commercial explosives detectors detect the higher vapor pressure materials but not the whole spectrum. This paper describes the basic properties of explosives molecules and our research to utilize these properties for increased detection sensitivity.
The operating histories and performance of a large (180 MWsub(e)) central condensing plant and five small (5 MWsub(e)) wellhead backpressure power plants are presented. The thermodynamic performance of the central plant is compared with an estimated possible performance based upon the work of Michaelides. Both types of plant have been shown to be reliable despite some problems due to the contaminants which are associated with geothermal steam.
Developing DB system of piping reliability including the population data and service history of damaged piping for pilot power plant. Total weld counts of shop welds, field welds and welds for measuring instruments for 14 systems of Kori unit 3. Total weld counts of shop welds, field welds and welds for measuring instruments for 12 systems of Wolsung unit 2.
... The chemistry of paints and painting by A H. 1834-1915 Church (Paperback - Aug. 24, 2010) Buy new: $35.75 $27.17 17 Used & new from $20.42 Get it by Thursday, Sept. 8 if you order in the next 16 hours and choose one-day shipping. Eligible for FREE Super Saver Shipping. Only 1 ...
The World Wide Web has its historical roots in things such as the creation of the telegraph, the launching of the Sputnik and more, but it really all started in March 1989, when Tim Berners-Lee, a computer scientist at CERN in Geneva wrote a paper called Information Management: A proposal
A conference on geotechnics presented papers on soil properties, soil liquefaction, slope stability, pile foundations, numerical modelling, engineering geology, rock mechanics, cold regions engineering, oil sands, irrigation, environmental engineering, geosynthetics, and geotechnical case histories. Separate abstracts have been prepared for 29 papers from the conference.
Objective: Optimization and testing of a high temperature combustion chamber for burning coal gas and conventional fuels natural gas or fuel oil. Coal gas is not available in such quantity for testing a full scaled combustion chamber. Therefore the design of the combustion chamber is based of experimental results from model tests and numerical solution procedures. Working program: (1) Analytical model for burning coal gas implemented in an existing computational fluid dynamics (CFD) code. (2) Three-dimensional calculations of a full scaled combustion chamber with a CFD code for flows accompanied by combustion and chemical reaction. (3) Improvement of measuring method for determination of flame temperature and concentration. (4) Temperature and concentration profil measuring in a full scaled combustion chamber by operating with natural gas or fuel oil. Results: An analytical model for burning coal gas was implemented in an ...
This report presents the operating results for Run 243 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary objective was to demonstrate the effect of a dissolver on the ITSL product slate, especially on the net C/sub 1/-C/sub 5/ gas production and hydrogen consumption. Run 243 began on 3 February 1983 and continued through 28 June 1983. During this period, 349.8 tons of coal was fed in 2947 hours of operation. Thirteen special product workup material balances were defined, and the results are presented herein. 29 figures, 19 tables.
This dissertation deals with both the theoretical and the technological aspects of monolithic tunable lasers, and the experimental techniques for opto-electronic integration. In the theoretical part, the principles and limitations of wavelength tuning and spectral linewidth reduction in monolithic semiconductor lasers are described, with coupled distributed feedback-Fabry Perot (DFB-FP) lasers and long DFB lasers as examples. Stepwise tuning of wavelength over tens of nanometers and continuous tuning over the range of a mode spacing are shown to be possible. Spatial hole burning is found to affect the spectral linewidth of lasers involving strong active gratings. On the technological side, one of the major issues is the fabrication of flexible gratings. Direct-writing techniques, such as focused ion beam (FIB) implantation and e-beam lithography, provide the resolution, flexibility and accuracy that conventional holographic lithography lacks. The parasitic ...
To get a considerable reduction of the radiotoxicity due to americium, a thermal neutron fluence of 2.10{sup 22} cm{sup -2} or a fast neutron fluence of 2.10{sup 24} cm{sup -2} is required. Irradiation in a thermal neutron flux leads to lower masses of {sup 234}U and precursors and of {sup 237}Np and precursors, but to higher curium masses and much higher neutron emission rates than irradiation in a fast neutron flux. Therefore, irradiation in a fast neutron flux has preference when multiple recycling is adopted. When once-through burning is applied, irradiation in a thermal neutron flux can be applied. Then irradiation in a heavy water reactor (HWR) has preference above irradiation in a PWR or in a high temperature gas-cooled reactor (HTGR). (authors) 4 refs.
To get a considerable reduction of the radiotoxicity due to americium, a thermal neutron fluence of 2.10{sup 22} cm{sup -2} or a fast neutron fluence of 2.10{sup 24} cm{sup -2} is required. Irradiation in a thermal neutron flux leads to lower masses of {sup 234}U and precursors and of {sup 237}Np and precursors, but to higher curium masses and much higher neutron emission rates than irradiation in a fast neutron flux. Therefore, irradiation in a fast neutron flux has preference when multiple recycling is adopted. When once-through burning is applied, irradiation in a thermal neutron flux can be applied. Then irradiation in a HWR has preference above irradiation in a PWR or in a HTGR. (orig.).
Recently we have made measurements of thermonuclear burst energetics and recurrence times which are unprecedented in their precision, largely thanks to the sensitivity of the Rossi X-ray Timing Explorer. In the "Clocked Burster", GS 1826-24, hydrogen burns during the burst via the rapid-proton (rp) process, which has received particular attention in recent years through theoretical and modelling studies. The burst energies and the measured variation of alpha (the ratio of persistent to burst flux) with accretion rate strongly suggests solar metallicity in the neutron star atmosphere, although this is not consistent with the corresponding variation of the recurrence time. Possible explanations include extra heating between the bursts, or a change in the fraction of the neutron star over which accretion takes place. I also present results from 4U 1746-37, which exhibits regular burst trains which are interrupted by "out of phase" bursts.
This work describes a three-step pre-treatment route for processing spent commercial Ni Mo/Al_2O_3 catalysts. Extraction of soluble coke with n-hexane and/or leaching of foulant elements with oxalic acid were performed before burning insoluble coke under air. Oxidized catalysts were leached with 9 mol L"-"1 sulfuric acid. Iron was the only foulant element partially leached by oxalic acid. The amount of insoluble matter in sulfuric acid was drastically reduced when iron and/or soluble coke were previously removed. Losses of active phase metals (Ni, Mo) during leaching with oxalic acid were compensated by the increase of their recovery in the sulfuric acid leachate. (author)
The evolution of intermediate and high mass stars is reviewed focusing on the interpretation of Pop I Cepheids. First, a summary is given of the classical results of stellar evolution theory for the main evolutionary phases (main sequence and core He-burning) all over the HR diagram, putting into evidence the various points of disagreement with current observational data. Second, models incorporating the effect of convective overshoot, are reviewed, and studies are presented on the rich, young clusters in the Large Magellanic Cloud, in which the models are compared with the observational data. Arguments are given to favor the adoption of models with convective overshoot instead of the classical ones. Third, new results are presented for pulsational models of the Cepheid stars, and the shape of the instability strip in the HR diagram, the number frequency-period distribution, and the mass discrepancy are discussed. 81 refs.
A stratigraphic and geochemical study of alpine soils, which formed in later Pleistocene (late glacial) and Neoglacial deposits in the Wind River Mountains of western Wyoming, indicates that these soils are affected by air-fall in flux of inorganic pollutants. Arsenic, bromine and antimony appear to have been deposited in surface soils by incorporation of aeolian materials which were presumably transported by winds from industrial sources, including coal-burning operations. As vanadium was not found in surface soils at concentrations above site-specific background levels, oil-fired energy generating stations were not found to be significant sources of surface soil pollution in the region. Acid-rain effects were not observed in the soils. (author) 32 refs.; 2 figs.; 3 tabs.
In this paper we discuss a number of astrophysical environments and how improved nuclear data could facilitate a better understanding of them. One area of interest includes proton and alpha-particle reactions with unstable nuclei which are necessary for understanding the nucleosynthesis and energy generation in hot hydrogen-burning environments. Efforts underway at LLNL and elsewhere to develop the technology for the measurement of these reaction rates are discussed. Heavy-element nucleosynthesis in the late stages of red-giant stars and supernovae requires a complete network of neutron capture rates and beta-decay rates for nuclei near and far from stability. Experimental and theoretical efforts at LLNL to supply the input data and to model the nucleosynthetic environments will be outlined. Suggestions are made as to which nuclear data are most critical for the various scenarios. 42 refs., 11 figs., 1 tab.
Very important performances in the practical use of solid propellants are combustion and physical properties. Among the present solid propellants, composite propellants used ammonium perchlorate (AP) as oxidizers are adopted widely now due to these excellent performances. Recently, a combination of ammonium nitrates (AN) as oxidizers and azido polymers as binders in expected as the propellants which control decrease of combustion properties and satisfy unsensitivity. However, in order to use these azido polymers/AN propellants in practice, further, it is necessary to improve the specific impulse and the burning rate. In this report, aiming to improve the combustion properties of BAMO/NMMO/AN propellants, the sensitivity and the combustion properties of propellants added high energetic plasticizers in binders, further, displaced a part of AN to cyclotetramethylenetetranitramine (HMX) and double based base-grain (BG) are described. 8 refs., 3 figs., 3 tabs.
The influence of radiation on the corrosion of the fuel claddings in a Light Water Reactor (LWR) has been the subject of many investigations, and different aspects of the overall phenomena have been studied by different techniques. Analysis of the evolution of Secondary-Phase Particles (SPPs) for different periods of immersion of the cladding in the reactor enables the rate of corrosion to the structure of the material to be correlated. In the case of Zircaloy-2 in a Boiling Water Reactor (BWR), SPPs are dissolved under irradiation, and their dissolution affects the rate of oxidation and other correlated phenomena. In recent studies, the Zircaloy-2 in claddings loaded in the Leibstadt BWR are analysed after one, three and five cycles. Results are presented, and give an account of the changes which occurred in the materials under irradiation. (authors)
In the GE 7FDL single cylinder research diesel engine, in-cylinder high-speed photographic studies were conducted on coal-water slurry (CWS) fuel combustion. Distinct flames of pilot and CWS combustion were noticed. It was proven that the coal fuel burns after piston impingement and secondary atomization. Agglomerated particles will develop when combustion conditions are not favorable. Cylinder pressure data were simultaneously recorded for each film frame. Heat release data can thus be produced for each photo study. Most of the findings of earlier combustion studies on engine performance were confirmed.
Photodestruction has received much attention in recent years. In particular, titanium dioxide (TiO{sub 2}) and ozonolysis have attained a position of prominence. These technologies hold promise for the destruction of trace amounts of aqueous high explosives that are generated by load and pack operations, as well as demilitarization activities. Currently this water is treated by passing through a bed of activated carbon. The carbon is then steam regenerated and reused, thus creating a second waste stream which must be disposed of, or the carbon is burned directly. Recent trends in environmental regulation have shown that this may not be a viable option for process water remediation in the future. This talk will discuss efforts to employ alternate aqueous treatment techniques that not only remove the explosives compounds but are able to transform the parent compound into carbon dioxide and water. Titanium dioxide photocatalysis as well as UV-ozone photolysis will be ...
The disrupted magnetic braking theory for the period gap of cataclysmic variable systems is used to study the binary evolution of low-mass main-sequence-like stars with white dwarf companions. The model is able to reproduce the observed location and width of the gap provided that the average mass transfer rates above the upper edge of the gap are greater than about 1.9 x 10 to the -9th solar masses/yr. For the case of angular momentum loss by magnetic braking, the slope of the mass transfer rate with respect to orbital period is shown to range from 3.4 to 3.7. For the evolutionary sequences considered, the He-3 abundance at the surface of the secondary exceeds 0.0015 after the complete mixing phase, resulting in modifications in the nuclear burning development of nova explosions. 31 refs.
Ogden Environmental Services has announced that the Environmental Protection Agency (EPA) has issued a nation-wide federal permit allowing OES to use its circulating bed combustion (CBC) system for remediation of PCB contaminated soils. The landmark permit confirms the effectiveness of OES' CBC system and its ability to destroy PCBs without releasing harmful quantities of PCBs or other chemicals into the air. EPA headquarters issued the permit following their audit of trial burn operations of OES' CBC unit during September 1988 at the Arco Swanson River oil fields in the Kenai Wildlife Refuge, Kenai Peninsula, Alaska. The Arco project represents the world's first major remediation program using CBC technology and the largest PCB/soil cleanup to date.
Nuclear reaction rates and opacity are important parameters in stellar evolution. The input physics in a stellar evolution code determines the main theoretical characteristics of the stellar structure, evolution and nucleosynthesis of a star. For different input physics, in this work we calculate stellar evolution models of very massive first stars during the hydrogen and helium burning phases. We have considered 100 and 200M_sun galactic and pregalactic stars with metallicity Z = 10"-"6 and 10"9, respectively. The results show important differences from old to new formulations for the opacity and nuclear reaction rates, in particular the evolutionary tracks are significantly affected, that indicates the importance of using up to date and reliable input physics. The triple alpha reaction activates sooner for pregalactic than for galactic stars.
Abstract Smoke is a mixture of toxic gases and suspended particulate matter of solids and liquids that evolves from a fire of flammable materials. This article presents real-time consequence modeling to track the concentration of individual species in smoke as well as its soot deposition. In the modeling process presented, the burning rate or vapor mass is fed into a combustion model in which the combustion of products has been identified and quantified along with the temperature of the fire. The output of the combustion model is the smoke that will be dispersed into the ambient. The fire geometry, which depends on the type of fire (e.g., pool or flare), is identified. A dispersion model with the capability of determining particulate deposition is then used for tracking the smoke plume. Th...
"1"0"1Mo is one of the key nuclides in diagnosing fission burn-up. However, it's difficult to measure its nuclear decay data due to its short half-life. Present study concerns in the measurements of #gamma#-ray emission probabilities, P_#gamma#, of "1"0"1Mo and "1"0"1Tc using the balance of scheme method and the entire process recording. The P_#gamma# of "1"0"1Mo by the entire process recording is about 5% lower than that by using the balance of scheme method. The P_#gamma# of "1"0"1Tc using the two methods agree each other very well. So, it seems the #gamma#-ray emission probabilities as well as measurement method still need study further for "1"0"1Mo. (authors)
Strut lattice structures of reaction-bonded silicon infiltrated silicon carbide ceramics (RB-SiSiC) for air-fuel mixture formation and for nonstationary lean-burn under pressure applications were fabricated. The lattice design with a high porosity >80% was shaped by indirect three-dimensional printing. It was shown that pre-ignition processes in the porous reactor are much faster than in a free combustion, especially at lower temperatures. Interaction of high velocity diesel jets with cylindrical strut ligaments of the SiSiC lattice structure offers a new possibility for quick and efficient fuel distribution (multi-jet splitting) in space.
In this paper compression and power stroke cycles for a 4 stroke cycle spark ignition engine modified by extending the connecting rod to simulate purely sinusoidal piston motion are analyzed over a range of operating speeds and are compared with those of a similar conventional engine. Heat release rate is estimated for both engines using a simple Wiebe function with the functional parameters found via a simplex curve fitting method is used in conjunction with experimental pressure curves. It is shown that the functional parameters which represent the combustion and duration of fuel burn are slightly larger over the range of operation in the sinusoidal engine while the shape factor remains largely the same.
The most effective way to generate electricity out of biomass is the gasification and the use of the gas in a gas engine. The conversion of the organic carbon with the gasification of biomass is higher than 95 %. Depending on the gasification concept, the efficiency of gasifiers is found between 70 and 90 %. If the pyrolysis gas is used in a gas engine, an electric efficiency of about 26 % referring to the primary amount of energy can be obtained. With efficient gas cleaning (cleaning for tar and dust), pyrolysis gas is well qualified for engine combustion. Through modern state of engine controlling there are ways to have complete control of the fluctuations in the gas composition. Furthermore, the minor calorific value of offered wood gas poses no problem for turbo charged lean-burn gas engines. (orig.)
Knowledge on environmental variability and how it is affected by disturbances is crucial for understanding patterns of biodiversity and determining adequate conservation strategies. The aim of this study is to assess environmental variability in patches undergoing post-fire vegetation recovery, identifying trends of change and their relevant drivers. We particularly evaluate: the value of three spectral indices derived from Landsat satellite data [Normalized Burn Ratio (NBR), Normalized Difference Vegetation Index (NDVI) and Wetness Component of the Tasseled Cap Transformation (TCW)] for describing secondary succession; the effectiveness of three metrics (diversity, evenness and richness) as indicators of patch variability; and how thematic resolution can affect the perception of environme...
In seeking ways to reduce emissions from two-stroke locomotive type engines, the Navy has evaluated dual-fuel conversions operating on a compression ignition cycle, using up to 94% natural gas and 6% diesel pilot fuel. The Navy has conducted an evaluation and test program under the direction of Dr. Normnn L. Helgeson, at the Naval Facilities Engineering Service Center in Port Hueneme, California. Of the Navy`s many diesel engines, those installed in its MUSE (mobile utility support equipment) units for temporary electrical power were the first Navy off-road engines to be affected by emissions regulations. Most of the units are powered by the EMD 645 engine, and when burning diesel fuel do not meet the emission requirements in many areas of the country. This paper discusses the changes and results of the conversion and shakedown tests.
A reference design was used in preparing a mathematical model of a fusion power plant with a tokamak reactor to investigate the extent to which the uncertainty still inherent in the physical reactor parameters affects the power costs. While only limited reductions of the power costs are achieved by improvements of the reference values for the reactor burn time, power density in the torus and load on the first wall, the power costs rise in keeping with the extent to which these parameters fall short of the reference values. As the results obtained in present-day experiments are still well below the reference values, a great deal of effort is still required in the fields of plasma physics and materials research to achieve an economically operating fusion power plant. (orig.).
Hydrate addition at low temperature (or the HALT process) is a retrofit option for moderate SO/sub 2/ removal efficiency in coal burning utility plants. This dry FGD process involves injecting calcium based dry hydrate particles into flue gas ducting downstream of the air preheater where the flue gas temperature is typically in the range of 280-325/degree/F. This report is comprised of the conceptual scaleup design of the HALT process to a 180 MW and a 500 MW coal fired utility station followed by detailed capital and operating cost estimates. A cost sensitivity analysis of major process variables for the 500 MW unit is also included. 1 fig.
This BCRS project demonstrates the use of SAR interferometry for measuring and monitoring land subsidence caused by underground coal fires and underground mining in a remote area of north west China. China is the largest producer and consumer of coal in the world. Throughout the N.W., N. and N.E. of China, the coal-seams are very susceptible to spontaneous combustion, causing underground coal fires. As the thick coal seams are burned out, the overburden collapses, causing land subsidence, and producing new cracks and fissures, which allow more air to penetrate and continue the fire to spread. SAR interferometry, especially differential interferometry has been shown to be able to measure small differences in surface height caused by such land subsidence. This report describes the problems, the test area, the procedures and techniques used and the results obtained. It concludes with a description of some of the problems encountered during the project plus provides ...
The principal objective of this study is to formulate an effective optimal fuel management strategy for the TRIGA MARK II research reactor at AERE, Savar. The core management study has been performed by utilizing four basic types of information calculated for the reactor: criticality, power peaking, neutron flux and burnup calculation. This paper presents the results of the burnup calculations for TRIGA LEU fuel elements. The fuel element burnup for approximately 20 years of operation was calculated using the TRIGAP compute code. The calculation is performed in one-dimensional radial geometry in TRIGAP. Inter-comparison of TRIGAP results with other two calculations performed by MVP-BURN and MCNP4C-ORIGEN2.1 show very good agreement. Reshuffling at 20,000MWh step provides the highest core l...
In certain regions of the sea floor, water and methane from organic depositions have turned into a burnable form of ice, i.e. methane hydrates which contain more stored energy than all fossil fuel reserves. If they should desintegrate as a result of global heating, methane will be released and will contribute to further global heating. [Deutsch] Im Boden bestimmter Meeresregionen haben sich Wasser und Methan aus organischen Ablagerungen zu einer brennbaren Form von Eis vereinigt. Diese Methanhydrate speichern mehr Energie als alle fossilen Brennstoffvorraete. Wenn sie sich bei einer globalen Erwaermung zersetzen, koennte das entweichende Methan als Treibhausgas die Erde noch mehr aufheizen. (orig.)
Raniganj and Jharia regions together have been for long the single largest coal supplier in India, now contributing about a quarter of the total output in the country. Numerous reasons such as improper mining techniques and policy, as well as unauthorized mining caused surface and subsurface coalfires in these areas. These coalfires burn millions of tonnes of valuable coal resources, creating severe environmental problems and posing enormous operational difficulties of mining. After first use of remote sensing as a tool to identify coalfires in 1960s, with the time, the efficiency of remote sensing to identify and monitoring coalfires has been well established by several researchers. With the knowledge of local geological setting and density sliced surface temperature image the spatial dis...
The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x10{sup 19} n {omega} cm{sup -1}. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual {sup 32}P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially p-type silicon ingot was established.
The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x1019 n ? cm-1. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual 32P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially p-type silicon ingot was established.
The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x1019ncm-1. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual 32P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neut...
During FY1997, the JMTR was operated for 3 complete cycles (120th, 121st and 122nd cycles) and was utilized for the research and development programs on the technology of LWRs and fusion reactor, as well as for fundamental research of fuels and materials, and for radioisotope productions. The improvement of evaluation technique in a local neutron spectrum for irradiation utilization and development of capsule having the vertical migration, the reinstrumentation and loading mechanism have been carried out. Development of a new oxygen potential sensor for oxide fuel pellets has been done as an elemental technology of irradiation for high burn-up fuels. As for post irradiation examination, the techniques for measuring of crack length using an alternating current potential drop method and machining of miniaturized specimen by the remote handling have been developed. A research on the blanket materials and components for thermonuclear fusion reactor were also ...
If two loops are isomorphic, then it is shown that their holomorphs are also isomorphic. Conversely, it is shown that if their holomorphs are isomorphic, then the loops are isotopic. It is shown that a loop is a Smarandache loop if and only if its holomorph is a Smarandache loop. This statement is also shown to be true for some weak Smarandache loops(inverse property, weak inverse property) but false for others(conjugacy closed, Bol, central, extra, Burn, A-, homogeneous) except if their holomorphs are nuclear or central. A necessary and sufficient condition for the Nuclear-holomorph of a Smarandache Bol loop to be a Smarandache Bruck loop is shown. Whence, it is found also to be a Smarandache Kikkawa loop if in addition the loop is a Smarandache A-loop with a centrum holomorph. Under this same necessary and sufficient condition, the Central-holomorph of a Smarandache A-loop is shown to be a Smarandache K-loop.
Abstract A complete study of an exploding bridgewire detonator (EBW), an LX-07 hemispherical booster and a PBX 9502 outer shell are described. Breakout times from all three are listed in terms of first impact on the booster, i.e., code times. Lucite windows are also used to obtain particle velocities at the edges of each explosive, and these are converted into explosive pressures. The key to modeling is the use of the profile of the aluminum detonator can as it impacts the booster, i.e., we need to know the curvature of the end of the booster can. Modeling even with coarse zoning shows that (i) using reactive flow in the booster is better than programmed burn, (ii) creating the flyer curvature helps, and (iii) creating the time differences of flyer impact helps even more.
W. E. B. Du Bois, one of the brightest lights in African American history, wrote a sparkling critique of the American social and economic system originally planned as part of the Bronze Booklets series, edited and published by Alain Locke and the Associates in Negro Folk Education. The piece was never published and has, until now, been lost to the annals of adult education history. Using historical evidence, the authors examine Du Bois's Basic American Negro Creed and the circumstances that led to its exclusion from the series. It is argued that the Creed was far too radical for the liberal minded Carnegie Corporation and its leaders who were only interested in accommodating adult education for Blacks through the AAAE funded Bronze Booklets. The exclusion of the Creed represents an example of repressive tolerance by the AAAE.
To determine the presence, prevalence, and clinical importance of /sup 99m/Tc pertechnetate uterine uptake, this retrospective analysis of 71 Meckel's scans was undertaken. Specifically, each study was evaluated for the presence of a focal accumulation of radiotracer cephalad to the bladder. Patients received an intravenous dose of 150 microCi/kg of /sup 99m/Tc pertechnetate. Each study consisted of 15 one minute anterior serial gamma camera images, and a 15, 30, and 60 minute anterior, right lateral and posterior scintiscan. Menstrual histories were obtained from all patients except two. No males (33/33), nor premenstrual (13/13), menopausal (4/4) or posthysterectomy (2/2) patients revealed a uterine blush. Eleven of 15 patients (73%) with regular menses demonstrated a uterine blush. They were in the menstrual or secretory phases of their cycle. Four demonstrated no uterine uptake, had regular periods, but were in the proliferative phase of their cycle. ...
The genetic type, source and charging history of natural gas in the Yulin gas field in the Ordos Basin have been studied by combining the carbon isotopic composition of natural gas and geochemical characteristics of light hydrocarbons with carbon isotope fractionation model results and fluid inclusion analysis. The carbon isotopic composition of methane and ethane in the Yulin gas field is relatively enriched in ^1^3C with d^1^3C1 values ranging from -35.3%% to -29.8%% (average value=-32.4%%) and d^1^3C2 ranging from -26.3%% to -23.5%% (average value=-24.8%%). The C7 light hydrocarbons are predominated by methylcyclohexane, accounting for 65.8% to 80.9% (average value=71.6%), which is characteristic of coal-derived gas. Furthermore, the gas geochemistry indicates that, although marine lime...
The seismic analysis of nuclear island of Daya Bay Nuclear Power Plant (NPP) was just in accordance with the approaches in RCC-G standard for the model M310 in France, in which the simplified impedance matrix method was employed for the consideration of soil's function. In this paper the more sophisticated 3D half-space continuum impedance method based on the Green functions is used to analyze the function of soil. In addition, multi-group of input time histories was used in the seismic response analysis in the existing design and their average of responses for each group was taken as the design basis. The same multi-group of input time histories was used in the seismic response analysis in this study, but the average and enveloped value of responses for each case are calculated respectively to account for the uncertainty of input motions. Focused on the above two issues, the seismic responses of the reactor building are calculated and the ...
A hydrogen combustion and exhaust emissions in a supercharged gas engine ignited with micro pilot diesel fuel was discussed in this presentation. A schematic diagram of the experimental study was first presented. The single cylinder, water-cooled, supercharged test engine was illustrated. Results were presented for the following: fuel energy and energy share (hydrogen and diesel fuel); pressure history and rate of heat release; engine performance and exhaust emissions; effect of nitrogen dilution on heat value per cycle; effect of N_2 dilution on pressure history and rate of heat release; and engine performance and exhaust emissions. This presentation demonstrated that smooth and knock-free engine operation results from the use of hydrogen in a supercharged dual-fuel engine for leaner fuel-air equivalence ratios maintaining high thermal efficiency. It was possible to attain mor3 than 90 per cent hydrogen-energy substitution to the diesel fuel ...
Objective. So far, few data are available to characterize the flare history of patients with gout. The objective of this study was to describe the frequency and risk factors of gout flares with special consideration of the comorbidity. Methods. A cohort study was conducted in a UK general practice database (The Health Improvement Network) including all patients aged 20-89 years diagnosed with incident gout between the years 2000 and 2007. Results. In this study, 23 857 incident gout patients (mean age 61.9 years) were included, overall incidence rate was 2.68 (95% CI 2.65, 2.72) per 1000 person-years. The proportion of patients with at least one flare during the follow-up period (mean 3.8 years) was 36.9% (n = 8806). A history of ischaemic heart disease [hazard ratio (HR) 1.12 (95% CI 1.06...
The characterization data obtained to date are described for Approved Testing Material 104 (ATM-104), which is spent fuel from Assembly DO47 of the Calvert Cliffs Nuclear Power Plant (Unit 1), a pressurized-water reactor. This report is one in a series being prepared by the Materials Characterization Center at Pacific Northwest Laboratory (PNL) on spent fuel ATMs. The ATMs are receiving extensive examinations to provide a source of well-characterized spent fuel for testing in the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) Program. ATM-104 consists of 128 full-length irradiated fuel rods with rod-average burnups of about 42 MWd/kgM and expected fission gas release of about 1%. A variety of analyses were performed to investigate cladding characteristics, radionuclide inventory, and redistribution of fission products. Characterization data include (1) fabricated fuel design, irradiation history, and subsequent storage and handling ...
Direct radionuclide cystography is known to be sensitive and safe in children with suspected vesical-ureteral reflux. In this study we have investigated the utility of direct radionuclide cystography in renal transplant recipients with a recent history of pyelonephritis or recurrent urinary infections. Direct radionuclide cystography is a simple test, however it requires a rigorous methodology in order to obtain images during fill-in as well as during voiding in both men and women. The images must be interpreted using a rigorous image display methodology. Twenty-eight radionuclide cystographies were performed in 17 patients. Among the 17 tests performed for the initial diagnosis of reflux , 12 were positive. Four patients with positive results and four patients with negative results were also investigated by radiologic cystography. Similar results were obtained in those patients. Nine scintigraphies were done after treatment by surgery or teflon injection ; six of ...
Website hosted by the American Ceramics Society with history of ceramics education, along with notable ceramic engineering educators. "In May 1894, two rooms in the basement of The Ohio State University?s College of Engineering were set aside to create a new department: Clay-Working and Ceramics. Founded with a $10,000 grant from the State of Ohio, the department was the first of its kind anywhere in the nation. The course of study was the idea and personal project of Edward Orton Jr., a young mining engineer. Orton had gathered his ceramic knowledge, piece by piece, from various jobs in coalmines, glass factories and steel plants. In 1893 he was the superintendent for a factory that made paving bricks. Orton?s factory, hit by an ?acute crisis,? closed, leaving him with some unexpected extra time. He used the opportunity to lobby for the passage of what some people dubbed the ?Mud Pie Bill? ? legislated funding to establish a school to train professionals in the ...
The thermomechanical behaviour of clayey soils was examined in a laboratory study because of their importance in some engineering applications such as hydrocarbon extraction from oil-bearing sands and radioactive waste disposal. The slightest temperature variations have been known to have an impact on the mechanical behaviour of clayey soils. In this study, tests were conducted on reconstituted and natural clayey soils using triaxial cells modified to control temperatures. Changes of temperature and stress state were not applied simultaneously. Instead, the tests were divided into two separate sections aimed at studying the thermal and mechanical behaviour of clays. The thermal behaviour tests examined the deformations induced by drainage temperature changes as well as pore-pressure generation and consolidation phenomena. The mechanical behaviour tests, focused on the influence of temperature and temperature history on compressibility, deformability and shear ...
The chemist and pharmacologist Fritz Hauschild developed the sympathomimetic agent Pervitin (metamphetamin) in the 1930s. Not only because of the abuse of the stimulant during the Second World War ("pilot's chocolate") it is one of the most controversial substances in drug history. Nearly forgotten are Hauschild's contributions to build up the drug system in the GDR. Although he was a convinced communist, the skilful pharmacologist gave very early warning of the imminent lack of innovation in the GDR pharmaceutical industry. A letter which he addressed to the Minister of Health, Max Sefrin (born 1913), did not lack explicitness. PMID:15997840
Ferrography is a technique for isolating wear particle debris from lubricating and hydraulic oils, the presence of which carry with them a history of the wear processes in the machine. Thus, the technique has fundamental applications in machine condition monitoring and failure prevention. The wear particles are significant in the metal types that are present in the particle distribution as an indication of the wearing machine components and in the particle size distribution and morphology which indicates the severity of wear in the system. In this paper, the fundamental principles which describe the working of the ferrograph, concentrating on the working of the on-line ferrograph are discussed. The significance of equilibrium particle concentration in the oil system and its measurement using the ferrograph are also discussed.
The heating history of a droplet during its flight can be divided into two phases: (a) the initial phase when evaporation, although it occurs, does not change the heat balance of the droplet much (the case considered in our previous paper and (b) the final phase when the cooling due to evaporation balances the heat flux from the plasma. The later phase is considered in Chen's comment. In our reply, a very straightforward consideration demonstrates that even in the final phase of the droplet flight, the 'rocket' effect can be significant. (reply)
Secondary ion mass spectrometry (SIMS), secondary electron microscopy (SEM) and X-ray analysis have been applied to the measurement of U-bearing particles with the intent of gleaning information concerning their history and/or origin. The lead isotopic abundances are definitive indicators that U-bearing particles have come from an ore-body, even if they have undergone chemical processing. SEM images and X-ray analysis can add further information to the study that may allude to the extent of chemical processing. The presence of 'common' lead that does not exhibit a radiogenic signature is clear evidence of anthropogenic origin. (author)
As there are many efforts devoted in order to manage the cancer, here the researcher handle one of these efforts that play a major part in treating the cancer internationally, it is a brachytherapy system. Brachytherapy was carried out mostly with radium sources, but recently some artificial sources are incorporated in this mode of treatment such as Cs-137, Ir-192, Au-198, P-32, Sr-90 and I-125. The research cover history of brachytherapy and radioactive sources used in, techniques of implementation, radiation protection and methods of brachytherapy dose calculation, as well as brachytherapy in radiation and isotopes centre in Khartoum.
Industrial activities in the river basin of the Elbe have a very long tradition, and have been resulting in the contamination of sediments for centuries. Contamination lasted until the fall of the iron curtain; since then, the situation has improved significantly. In the transition zone between freshwater systems and the marine environment, ports like Hamburg still have to bear this burden of history. An overall (contaminated) management strategy should be developed in the context of the European Water Framework Directive with the emphasis on source control. (orig.)
The purpose is to define sustainable economic development in the context of nonrenewable resources and to examine the changing nature of reclamation over time. Sustainable development is development that ensures the present utilization of resources and the environment does not damage prospects for their use by future generations. Polls show that the public is demanding higher environmental standards. One mechanism for achieving sustainable economic development for the nonrenewable resource sector is through reclamation. The Alberta government`s approach to reclamation is reviewed to show how reclamation and sustainable government are linked together. The history of reclamation legislation in Alberta is summarized. 10 refs.
Although the oil price is still far from its historical maximum, the oil market is today in crisis. To explain this situation the author discusses the nature of the supply constraints. The reserves are today better known and so more plentiful than at a previous period of the oil history and the russian production since 2004 is stagnating. The main factor seems to be the OPEC policy and in particular the will of limiting the oil production to defend upper prices. (A.L.B.)
A development history and current status evaluation are presented for nuclear-thermal rocket propulsion systems applicable to interplanetary flight. While the most advanced current chemical rocket engines, such as the SSMEs of the Space Shuttle, produce specific impulses of the order of 450 secs, a nuclear-thermal rocket engine tested at Los Alamos in 1969 generated 845 secs; such specific impulse improvements could represent weeks or months of interplanetary travel time. Attention is given to the achievements of the historical Nuclear Engine for Rocket Vehicle Application, Helios, and Orion design programs, as well as to the current Vehicle for Interplanetary Space Transportation Applications, which is fusion-based.
The author describes the history of the Soviet Unions nuclear weapons testing in Siberia from the first bomb on 29th August 1949 until the test-ban treaty of 1963. The effects of the weapons testing on the local population is only now becoming widely known. Levels of cancers and cataracts are significantly higher than in uneffected populations, and there are also high levels of some lung, bone, skin and digestive conditions. Perhaps the most important information relates to cataracts, previously thought to be caused by single large bursts of radiation. Regulatory authorities worldwide will need to tighten the safety limits for eye radiation exposure to these findings. (U.K.).
The author describes the history of the Soviet Unions nuclear weapons testing in Siberia from the first bomb on 29th August 1949 until the test-ban treaty of 1963. The effects of the weapons testing on the local population is only now becoming widely known. Levels of cancers and cataracts are significantly higher than in uneffected populations, and there are also high levels of some lung, bone, skin and digestive conditions. Perhaps the most important information relates to cataracts, previously thought to be caused by single large bursts of radiation. Regulatory authorities worldwide will need to tighten the safety limits for eye radiation exposure to these findings. (U.K.).
We compare the existing observational data on type Ia supernovae with the evolutions of the Universe predicted by a one-parameter family of tachyon models which we have introduced recently [Phys. Rev. D 69, 123512 (2004)]. Among the set of the trajectories of the model which are compatible with the data there is a consistent subset for which the Universe ends up in a new type of soft cosmological singularity dubbed big brake. This opens up yet another scenario for the future history of the Universe besides the one predicted by the standard #LAMBDA#CDM model.
The energy fed by active galactic nuclei to the surrounding diffuse baryons changes the latter's amount, temperature, and distribution; so in groups and in member galaxies it affects the X-ray luminosity and also the Sunyaev-Zel'dovich effect. Here we compute how the latter is enhanced by the transient blastwave driven by a shining quasar, and is depressed when the equilibrium is recovered with a depleted density. We constrain such depressions and enhancements with the masses of relic black holes in galaxies and the X-ray luminosities in groups. We discuss how all these linked observables can tell the quasar contribution to the thermal history of the baryons pervading galaxies and groups.
The structural integrity of the Fuel Test Loop(FTL) in a Korean experimental reactor is evaluated when the FTL, submerged in a water environment, is subjected to a postulated pipe rupture. The analyses are performed under static and dynamic conditions, imposing the thrust force history at each postulated pipe rupture section. Through analysis the following results are found: 1) A double ended guillotine can not be expected based on the toughness of the material, 2) the structural integrity of the chimney surrounding the FTL would not impede the structural integrity by the pipe whip. All analyses are performed by finite element methods.
We report a case of stress fracture of the clavicle associated with sternocostoclavicular hyperostosis. A 60-year-old man sustained a stress fracture of the right clavicle with no history of trauma. On radiography, hyperostosis of the anterior chest wall and ankylosis of the sternoclavicular joint were evident in addition to the fracture. Fracture healing was uneventful after 2.5 months. Ankylosis of the sternoclavicular joint may have caused increased stress at the midshaft of the clavicle by daily activity or minor trauma. Such a fracture is a rare complication of sternocostoclavicular hyperostosis. (orig.)
The utilization of nuclear medicine bone scanning examinations early in the diagnostic process allows physicians to render prompt and correct treatment in urgent or difficult athletic cases. Bone scanning should be performed for athletic injuries whenever (1) x-rays are normal but bone or joint pain persists; (2) x-rays are positive but it cannot be determined if the findings are acute or chronic; (3) soft-tissue injuries present and x-rays are not useful; and (4) bone pain or joint impairment present without a history of trauma.89 references.
Primary B-cell lymphoma of thymus is uncommon. We describe the case of a 23-year-old woman with a history of shortness of breath and distended neck veins of 1-month duration. A chest roentgenogram and computed tomographic chest scan of the showed a large anterior mediastinal mass. Tru-cut biopsy revealed primary B-cell lymphoma of thymus. She underwent chemotherapy with no symptomatic improvement. Post-chemotherapy computed tomographic scan of the chest showed no appreciable reduction in tumor size. Surgical excision was carried out with excellent results.
The nature of the first generation of stars in the Universe remains largely unknown. Observations imply the existence of massive primordial stars early in the history of the universe, and the standard theory for the growth of cosmic structure predicts that structures grow hierarchically through gravitational instability. We have developed an ab initio computer simulation of the formation of primordial stars that follows the relevant atomic and molecular processes in a primordial gas in an expanding universe. The results show that primeval density fluctuations left over from the Big Bang can drive the formation of a tiny protostar with a mass of just one percent that of the sun. The protostar is a seed for the subsequent formation of a massive primordial star.
A computerised glow curve deconvolution (CGCD) analysis was applied to the main dosimetric peak of #alpha#-Al_2O_3:C in order to study the effects of light on the glow curve shape. It was shown that both the light-induced signal and the light-induced fading effects tend to shift the main dosimetric peak to higher temperatures and at the same time change its shape. Furthermore it was confirmed that the magnitude of the light-induced signal depends on radiation history and, by increasing the duration of light exposure, the magnitude of the light-induced signal reaches a plateau, thereby implying the saturation of the phototransfer process. (author).
S. 1484 is intended to change the oil-shale-leasing provisions of the Mineral Leasing Act of 1920 to encourage development of oil-shale resources on federal and non-federal lands. It authorizes the Secretary of the Interior to lease land for mining and additional land for waste-disposal and construction facilities. The text of S. 1484 is followed by the background and legislative history of the bill, a section-by-section analysis of the bill, and an evaluation of its budgetary and regulatory impacts. Pertinent communications are reprinted with recommendations and additional views. (DCK)
Despite their simplicity, diatomic molecules of first row elements can exhibit very complex phase diagrams. Determination of the phase diagrams can be further complicated by the existence of hysteretic molecular phases that can be observed over large regions of coexistence. Here we present evidence for a previously unreported molecular phase of nitrogen existing at room temperature at least over the range of 33-74 GPa. Our measurements show that sample history may have a significant impact on the thermodynamic states accessed by the molecular nitrogen solid and, by extension, also on the established phase diagram.
Attention is paid to the production mechanisms of light scalars that reveal their nature. We reveal the chiral shielding of the \\sigma(600) meson. We show that the kaon loop mechanism of the \\phi radiative decays, ratified by experiment, points to the four-quark nature of light scalars. We show also that the light scalars are produced in the two photon collisions via four-quark transitions in contrast to the classic P wave tensor q\\bar q mesons that are produced via two-quark transitions $\\gamma\\gamma\\to q\\bar q$. The history of spontaneous breaking of symmetry in quantum physics is discussed in Appendix.
This article gives a survey of the history, properties and applications of 'Kevlar' aramide fibers. For example, the 'Kevlar' para-aramide fiber is used in compound materials in ship-, aircraft- and vehicle construction. 'Kevlar' is used as a replacement for asbestos, for example in brakes, clutches and seals or as rubber reinforcement (tyres, conveyor belts, hoses). The aramide fibers also offer manufacturers of ropes, hawsers and cables a near ideal range of properties. (MM).
Most of the essays gathered in this volume were first presented at a conference, Justice and the Human Genome, in Chicago in early November, 1991. The goal of the, conference was to consider questions of justice as they are and will be raised by the Human Genome Project. To achieve its goal of identifying and elucidating the challenges of justice inherent in genomic research and its social applications the conference drew together in one forum members from academia, medicine, and industry with interests divergent as rate-setting for insurance, the care of newborns, and the history of ethics. The essays in this volume address a number of theoretical and practical concerns relative to the meaning of genomic research.
The most important and difficult part of materials research for fusion reactor is realized to be irradiation studies of fusion reactor materials. Irradiation studies of fusion reactor materials utilizing FFTF/MOTA, as one of Japan/U.S.A. Fusion Collaboration Programs, have important role to establish fundamental understanding of heavy irradiation effects on materials behavior and properties and to develop methods and technologies for advanced irradiation studies under fusion reactor environment. This paper briefly reviews the history, the state of the art, and the future of the FFTF/MOTA program. (author).
The introduction prior to series of papers on the application of neutrons for materials science (MS) in this issue starts with a brief summary of neutron scattering research history in Japan; from the individual activity by Motoharu Kimura at RIKEN early around 1940s to those at present era of world leading neutron science facilities of both JRR3 research reactor and JPARC of the largest proton Accelerator complex in Tokai. Then physical properties of low energy neutrons applied to MS as well as such neutron sources are also reviewed (http://www.jstage.jst.go.jp/browse/jvsj2). (author)
This article discusses the Daya Bay nuclear power plant in-core flux thimble tube in-service inspection method and strategy. High light of the multiple frequency eddy current technology adopted including frequency and probe choice, standard design, data acquisition process are involved. The wear defect-growing trends are studied on base of the history data, which contribute to the in-service inspection strategy decision. (authors)
A 1.5-year-old male Belgian Malinosis Military Working Dog presented with a 1-month history of intermittent hematuria. Diagnostic ultrasound and contrast radiography demonstrated large blood clots in the urinary bladder and a filling defect in the right renal pelvis. At surgery, clotted blood was present in the right ureter and bladder. Following right nephrectomy, the dog returned to training. One month later, elevations in urea nitrogen and creatinine were noted. Hematuria recurred at 3 months and the dog was found dead in its kennel. Necropsy showed a blood-filled left renal pelvis and ureter. PMID:1454185
This bulletin traces development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of pertinent literature. The bulletin written as part of the Bureau of Mines research program on synthetic liquid fuels covers the history and economics of the process; chemical aspects of hydrogenation of coal, tar, and middle oil; engineering aspects of converting coal and tar to liquid fuels, principally gasoline; and equipment for the process. The literature covered includes documents of United States and British governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.
This study presents a theoretical analysis of heat generation and dissipation of field-controllable magneto-rheological fluid (MRF) shock absorbers. Since MRF dampers are energy- dissipating devices, the issues of heat generation and dissipation are important in predicting their performance. A theoretical model is developed based on Bingham plastic model to estimate temperature history of the MRF dampers. The governing equation includes the MRF viscosity as a function of the temperature. The numerical solutions are compared with experimental results in order to validate the accuracy of the model, and excellent agreements are obtained.
Tube failures due to excessive flow-induced vibration must be avoided to assure the reliable performance of heat exchangers. Such components must be thoroughly analysed for vibration at the design stage. Several flow-induced vibration mechanisms are possible. In this paper, particular attention is given to fluidelastic instability of tube bundles subjected to liquid and two-phase cross-flow. The performance of ten operating heat exchanger components is reviewed to validate our recommended vibration analysis guidelines. Both tube failure histories and satisfactory performances are considered. The results show that a fluidelastic instability constant K=3.3 is a reasonable design criterion. (auth).
The Rosebel gold district is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield and has many characteristics that enable classification of the ores as an orogenic gold deposit. Host rocks have undergone several phases of deformation. However, gold deposition occurred late in the structural history of the belt, and is considered part of a late regional metallogenic event with respect to the geotectonic evolution of the Guiana Shield. Economic gold mineralization is hosted in felsic to mafic volcanic rocks and two sedimentary successions that are differentiated into turbiditic and arenitic depositional packages. The detailed lithostratigraphic characterization and the geochemistry enable the correlation of the local rock types with the Paramaka, the Armina, and the Rosebel for...
In a program to develop a metastable beta alloy with improved fracture toughness, it was found that the tensile ductility of the alloy Ti-8 Mo-4.5 Cr-2.5 Al was strongly dependent on both processing history and annealing temperature. Evaluation of the microfracture mode of tensile samples by scanning electron microscope and metallographic techniques showed that the presence of a continuous grain boundary alpha is the most significant parameter controlling the ductility and is highly detrimental. It is concluded that, for optimum processing, the material must be worked prior to aging to avoid this grain boundary phase.
We describe a 16-month-old boy presenting with stridor and fever. The chest X-ray suggested inhalation of a foreign body but here was no history of this. A high spot a T_1-weighted chest MRI was due to a peanut which was seen to have moved from the right main bronchus to the left inferior bronchus, between the two MRI studies. MRI can provide information on position and size of the peanut, the conditons of the surrounding tissues and may be also useful in treatment. We consider MRI to be a valuable new method for the diagnosis of peanut inhalation. (orig./GDG).
In 1980 Sasol completed its very large coal conversion complex, Sasol Two and Three in South Africa. This complex, the largest coal-to-liquids facility in the world, utilizes Sasol's proprietary Fischer-Tropsch technology, the Synthol Process. The two key elements of the Synthol Process are its catalyst and its unique fluidized bed reactor, the Synthol Circulating Fluidized Bed Reactor. Details on the catalytic aspects and reaction mechanism have been given elsewhere. In this paper, the history of the development of the reactor is discussed.
In 1969, the authors started R and D on a polypropylene laminated paper (PPLP) as a new low-loss insulating paper for oil-filled (OF) cables. Through the material research and the trial manufacture of 275 kV OF cable and four years of long-term field test, PPLP has reached the stage of commercial use. This paper introduces a summary of the history of the development of PPLP, the characteristics of PPLP and cable, the results of long-term field test of 275 kV cable, and other relevant data.
The Northwest Foster Care Alumni Study examined the relation between experiences in foster care and depression among young adults who spent at least a year in foster care as adolescents. Results indicate that preparation for leaving foster care, nurturing supports from the foster family, school stability, access to tutoring, access to therapeutic service and support, and a shorter and more stable placement history were associated with a lower probability of depression in young adulthood. Results provide evidence that suggest ways to improve practice to decrease rates of depression among alumni of care. (Contains 2 tables.)
The addition of ZnO, depleted in the Zn-64 isotope, to the water of boiling water nuclear reactors lessens the accumulation of Co-60 on the reactor interior surfaces, reduces radioactive wastes and increases the reactor service-life because of the inhibitory action of zinc on inter-granular stress corrosion cracking. To the same effect depleted zinc in the form of acetate dihydrate is used in pressurized water reactors. Gas centrifuge isotope separation method is applied for production of depleted zinc on the industrial scale. More than 20 years of depleted zinc application history demonstrates its benefits for reduction of NPP personnel radiation exposure and combating construction materials corrosion.
In order to assess whether an oil shale test facility would be of significant use to private sector oil shale developers, the US DOE has studied the past history of oil shale development and its potential for replacing petroleum supplies. A generic test facility's primary function would be to test concepts of mining, retorting, upgrading, and environmental aspects at the engineering scale. This paper summarizes the US oil shale resources, gives a technology analysis, and discusses the potential for a test facility.
The authors trace the early history of nuclear power regulation in the US. Focusing on the Atomic Energy Commission, they describe the role of other groups that figured in the development of regulatory policies, including the Congressional Joint Committee on Atomic Energy, other federal agencies, state governments, the nuclear industry, and scientific organizations. They consider changes in public perceptions of and attitudes toward atomic energy and the dangers of radiation exposure. The basic purpose of the book is to provide the Nuclear Regulatory Commission and the general public with information on the historical antecedents and background of regulatory issues so that there will be continuity in policy decisions. The book concludes with an annotated bibliography of selected references. 19 figures.
The most common causes of tracheobronchial foreign bodies are peanuts in children, and meat and dentures in adults. The most common causes of esophageal foreign bodies are coins in children and meat in adults. It is passable to diagnose a foreign body by visualization on a chest radiograph, if the foreign bodies are radio opaque. However, if the foreign bodies are radiolucent and the patients do not remember the history of aspiration, it is important to evaluate CT findings for foreign bodies and their complications. We describe the CT findings of various thoracic foreign bodies in children and adults.
CT colonography (CTC) is increasingly advocated as an effective initial screening tool for colorectal cancer. Nowadays, policy-makers are increasingly interested in cost-effectiveness issues. A number of studies assessing the cost-effectiveness of CTC have been published to date. The majority of findings indicate that CTC is probably not cost-effective when colonoscopy is available, but this conclusion is sensitive to a number of key parameters. This review discusses the findings of these studies, and considers those factors which most influence final conclusions, notably intervention costs, compliance rates, effectiveness of colonoscopy, and the assumed prevalence and natural history of diminutive advanced polyps. (orig.)
The composition and thickness of etch residues on the base of submicrometer via holes cannot be surmized from data on larger features. Auger sputter depth profiles were used to compare etch residues in 0.55 {mu}m via holes produced by different etch processes and remaining after different cleans. These residues varied significantly in composition and thickness with the processing history of the sample and from those on larger features. A focused ion beam (FIB) sample preparation was developed to expose the bases of via holes and to help reduce sample charging. (author).
The current and prospective status of astronomical research in Ukraine is discussed. A brief history of astronomical research in Ukraine is presented and the system organizing scientific activity is described, including astronomy education, institutions and staff, awarding higher degrees/titles, government involvement, budgetary investments and international cooperation. Individuals contributing significantly to the field of astronomy and their accomplishments are mentioned. Major astronomical facilities, their capabilities, and their instrumentation are described. In terms of the number of institutions and personnel engaged in astronomy, and of past accomplishments, Ukraine ranks among major nations of Europe. Current difficulties associated with political, economic and technological changes are addressed and goals for future research activities presented.
Age is a key parameter when deducing the history of plutonium material, i.e. the plutonium produced in the nuclear reactors. This is of vital importance, when a smuggled plutonium sample has been seized and the origin has to be determined. A methodology is described which allows accurately to determine the age of plutonium material by thermal ionisation mass spectrometry using independent parent/daughter relations. This has been demonstrated for Reference Materials of known ages as well as for real samples. The already established method using gamma spectrometry is compared to this. (orig.)
This paper first reviews the history of the Port Hope uranium refinery of Eldorado Nuclear Limited. The current processes used for the production of UO_3, UO_2 and UF_6 from yellow cake are then discussed. Recent process changes and developments in the areas of solvent extraction and UO_3 production together with new processes for the production of ceramic UO_2 and UF_4, are described. Environmental and waste management problems, progress and solutions are next considered. Finally, some experience in siting a new UF_6 refinery, with respect to Environmental Impact Statements and public hearings, conclude the paper. (author).
Renal arteriovenous fistula or pseudoaneurysms developing after invasive procedures are either asymptomatic or show only transient symptoms. We describe here a case of symptomatic renal artery pseudoaneurysm that presented with gross hematuria and azotemia. The pseudoaneurysm of renal artery was diagnosed by ultrasonography and abdominal magnetic resonance imaging (MRI), and it was successfully treated by percutaneous transcatheter coil embolization. A high index of suspicion is essential for the early diagnosis and treatment of delayed gross hematuria in patients with history of percutaneous nephrostomy. PMID:17180737
Apatite fission track analysis, vitrinite reflectance data, and K-Ar dating of Permian-Carboniferous and Mesozoic core samples have been successfully integrated to reconstruct the thermal and tectonic history of the Ordos basin, China. Apatite fission track ages of Carboniferous-Jurassic sedimentary rocks range between 3 and 137 Ma, and are significantly younger than the stratigraphic ages. Confined fission track lengths demonstrate exclusively mixed length distribution, indicating complex thermal history. The data suggest that the samples must have all experienced higher paleotemperatures in the past. Mean virtinite reflectance values (R{sub o}) of the Triassic rocks range from 0.61 to 1.06%, giving a high coalification gradient of 0.36%/km and suggesting a high paleothermal gradient of 57{degrees}C/km. Permian-Carboniferous rocks have R{sub o} values on the order of 1.0-3.0%, and locally up to 4.0-6.0%. Some high R{sub o} values coincide with ...
The IPIRG-2 program was an international group program managed by the US NRC and funded by organizations from 15 nations. The emphasis of the IPIRG-2 program was the development of data to verify fracture analyses for cracked pipes and fittings subjected to dynamic/cyclic load histories typical of seismic events. The scope included: (1) the study of more complex dynamic/cyclic load histories, i.e., multi-frequency, variable amplitude, simulated seismic excitations, than those considered in the IPIRG-1 program, (2) crack sizes more typical of those considered in Leak-Before-Break (LBB) and in-service flaw evaluations, (3) through-wall-cracked pipe experiments which can be used to validate LBB-type fracture analyses, (4) cracks in and around pipe fittings, such as elbows, and (5) laboratory specimen and separate effect pipe experiments to provide better insight into the effects of dynamic and cyclic load histories. Also ...
This report describes the progress of the Dutch RAS programme on `Recycling and Transmutation of Actinides and Fission Products` over the year 1995, which is the second year of the 4-year programme 1994-1997. An extensive listing of reports and publications from 1991 to 1995 is given. Highlights in 1995 were: -The completion of the European Strategy Study on Nuclear Waste Transmutation as a result of which the understanding of transmutation of plutonium, minor actinides and long-lived fission products in thermal and fast reactors has been increased significantly. Important ECN contributions were given on Am, {sup 99}Tc and {sup 129}I transmutation options. Follow-up contracts have been obtained for the study of 100% MOX cores and accelerator-based transmutation. - Important progress in the evaluation of CANDU reactors for burning very large amounts of transuranium mixtures in inert matrices. - The first RAS irradiation experiment in the HFR, in which the ...
The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor, based on the experienced light water reactor (LWR) technology, aiming at effective utilization of uranium resources, high burn-up and long operation cycle and plutonium multiple recycling. These characteristics can be achieved by the high conversion ratio from {sup 238}U to {sup 239}Pu resulted from the higher neutron energy spectrum in comparison to conventional LWRs. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPC) in 1998, under technical cooperation with three Japanese reactor vendors. In the core design study of the RMWR, several basic core designs with the high conversion ratio more than 1 and the negative void reactivity coefficient have been proposed, and then, subsequent investigation on ...
The dominant shrubs were sagebrush and spiny hopsage; the herbs were dominated by cheatgrass and Sandberg bluegrass. Spiny hopsage appeared to be vulnerable to burning and also to damage by off-road vehicular traffic. It appears to have little or no ability to reproduce through seedlings; once the existing plants are killed they are not likely to be replaced, even if seed-producing plants are nearby. The only pure stand of spiny hopsage known to exist on the Hanford Site is on and near study plot 2H. Sagebrush, like spiny hopsage, is killed by burning and by heavy vehicles. Sagebrush is capable of reproducing via seeds, indicating that it is an inherently aggressive species with a capacity to reestablish itself if parent plants are in the vicinity to act as seed sources. Alien, annual plants, especially cheatgrass, were a major contributor to the herbaceous canopy cover in plots 3S, 4S, and 5S. However, native perennial grasses, especially ...
Burnaid is a sorbalene-based cream containing 40 mg/g of tea tree oil and 1 mg/g of triclosan. This investigation was carried out to determine the effect of Burnaid, a commercial tea tree oil preparation, against Enterococcus faecalis (ATCC29212), Staphylococcus aureus (ATCC29213), Escherichia coli (ATCC25922), and Pseudomonas aeruginosa (ATCC27853), with the activity of the base product in the commercial preparation. The organisms were suspended in sterile saline (0.5 McFarland Standard) and inoculated onto horse blood agar (E. faecalis and S. aureus) or Mueller-Hinton agar (E. coli and P. aeruginosa). One hundred microliters of Burnaid unsterilized, Burnaid sterilized and the base product (Tinasolve) were placed in duplicate in wells cut into the agar plates. Sterility and inactivation cultures were also performed on the samples. None of the samples were found to be contaminated with bacteria prior to testing. Only S. aureus and E. coli showed zones of growth inhibition around the ...
This facility has treatment capacity of 12 kg/hr, and is equipped with a furnace, two ceramic filter chambers, each of which hangs inside the 36 ceramic filter elements having mean pore size of 44 #mu#m. Three series of experiments were performed during a period from October 1972 to August 1973. The first was measurement of the change of pressure drop of the primary and the secondary filters after an operation of 52 days (352 hours). The pressure drop of the primary filter did not change during the operation, but the secondary brought a fairly large increment, from 79 to 140 mmAq. The second was measurement of the after-burning effect of the primary filter for the soot and tar in the off-gas. Through the after-burning most of the soot was removed from the off-gas, though the tar was not perfectly taken off. At the secondary filter, some of the tar was burnt, but most of it was caught by the filter as aerosol. The third was measurement of ...
Large scale experiments were performed to determine the effectiveness of thermal glow plug igniters to burn hydrogen in a condensing steam environment due to the presence of water sprays. The experiments were designed to determine if a detonation or accelerated flame could occur in a hydrogen-air-steam mixture which was initially nonflammable due to steam dilution but was rendered flammable by rapid steam condensation due to water sprays. Eleven Hydrogen Igniter Tests were conducted in the test vessel. The vessel was instrumented with pressure transducers, thermocouple rakes, gas grab sample bottles, hydrogen microsensors, and cameras. The vessel contained two prototypic engineered systems: (1) a deliberate hydrogen ignition system and (2) a water spray system. Experiments were conducted under conditions scaled to be nearly prototypic of those expected in Advanced Light Water Reactors (such as the Combustion Engineering (CE) System 80+), with prototypic spray drop ...
The burning characteristics of fuel droplets containing nano and micron-sized aluminum particles were investigated. Particle size, surfactant concentration, and the type of base fluid were varied. In general, nanosuspensions can last much longer than micron suspensions, and ethanol-based fuels were found to achieve much better suspension than n-decane-based fuels. Five distinctive stages (preheating and ignition, classical combustion, microexplosion, surfactant flame, and aluminum droplet flame) were identified for an n-decane/nano-Al droplet, while only the first three stages occurred for an n-decane/micron-Al droplet. For the same solid loading rate and surfactant concentration, the disruption and microexplosion behavior of the micron suspension occurred later with much stronger intensity. The intense droplet fragmentation was accompanied by shell rupture, which caused a massive explosion of particles, and most of them were burned during this ...
Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the combustion threat has received less ...
With the aid of a DOE grant (No. DE-FC26-01NT41050), Stolar Research Corporation (Stolar) developed the Horizon Sensor (HS) to distinguish between the different layers of a coal seam. Mounted on mining machine cutter drums, HS units can detect or sense the horizon between the coal seam and the roof and floor rock, providing the opportunity to accurately mine the section of the seam most desired. HS also enables accurate cutting of minimum height if that is the operator's objective. Often when cutting is done out-of-seam, the head-positioning function facilitates a fixed mining height to minimize dilution. With this technology, miners can still be at a remote location, yet cut only the clean coal, resulting in a much more efficient overall process. The objectives of this project were to demonstrate the feasibility of horizon sensing on mining machines and demonstrate that Horizon Sensing can allow coal to be cut cleaner and more efficiently. Stolar's primary goal was ...
The work presented here demonstrates the ability of proton-transfer-reaction mass spectrometry (PTR-MS) to perform fast-response measurements of volatile organic compounds (VOCs) (including methanol, acetonitrile, acetaldehyde, acetone, PAN-type compounds, alpha- and beta-pinene, nopinone and pinonaldehyde) at the pptv level and its versatile applicability in the field of environmental trace gas analysis. Laboratory and field experiments including various calibration techniques and intercomparisons with other measurement techniques such as gas chromatography, atmospheric pressure chemical ionization and Fourier transformation infrared spectroscopy were performed providing a first characterization of the PTR-MS instrument performance (sensitivity, detection limit, precision, accuracy). Typically a detection limit (S/N=2) of 50 pptv for a 10 s signal integration time, a precision of 5 % and an accuracy in the range between 10 and 25 % were observed. Due to its compactness and ruggedness ...
The blinded study of CBUE (cytobacteriological urine examination) test strips was carried out in 100 patients (65 women, 35 men), mean age 85.52 +/- 6.28 years, admitted for a short stay in a geriatrics department. Urinary infection was present in 19% of the cases. Typical clinical signs (pollakiuria, dysuria, hematuria, burning upon voiding) were rare, less than 10%. General signs, such as deterioration of general status (65% of the cases) and loss of autonomy (53% of the cases), on the other hand, were predominant and their relatively unspecific nature required a reliable screening test for urinary infection. Good results of sensitivity (89.5%), specificity (98.7%), and the leukocytes/nitrites values, confirmed the validity of the urine test strip in hospitalized elderly patients. In addition, the negative predictive value of the combination leukocytes and nitrites (90.8%) would have prevented 71 samples from being sent to the laboratory for CBUE, resulting in an ...
This report presents the operating results for Run 245 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an all-distillate Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary run objective was to obtain steady-state ITSL performance by replacing spent HTR reactor catalyst with fresh, sulfided catalyst. Secondary objectives were to maintain an all-distillate (minimum resid production) product slate and to demonstrate the effects of catalyst addition on the net gas production and hydrogen consumption. Run 245 began on 7 November, 1983, and continued through 12 February, 1984. During this period, 179.0 tons of coal was fed in 2045 hours of operation. Eight special product workup material balances were defined, and the results are presented herein. 6 references, 28 figures, 20 tables.
This report documents the concluding efforts at the Engineering Sciences Laboratory of TRW on two specific areas of current research activity within the more general context of proposed lean-burn operation of Otto-cycle-type automotive engines. These areas are: (1) achievement of knock-free performance, both under available fuels and current compression ratios and also under higher-octane fuels (e.g., alcohols) and higher-compression-ratio design (for greater thermal efficiency); and (2) identification of counterstrategies for two-wall (crevice-type) quenching of flame propagation, a phenomenon now widely acknowledged to be the major source of unburned-hydrocarbon emissions exhausted from homogeneous-charge cyclinders. There are certainly other highly active areas of research in Otto-cycle engines, such as turbocharging, ignition devices, and valve design, but the two above-cited topics were the topics of this project.
By increasing the price of crude oil and natural gas and the decline in their stock a possibility of more intense use of coal reserves as a feedstock not only for energy purposes but also as a feedstock source for other industries, mainly chemical and steel industry, is opening up. At present brown coal exploited in the Czech Republic is explicitly burned in the power sources of various outputs. Coal pyrolysis under the defined conditions may be an outstanding way of non-energetic brown coal processing. The target of our work was to determine the behaviour of various types of brown coal from the North Bohemian Basin under the pyrolysis up to the temperature 750{sup o}C. At the same time, qualitative parameters of the pyrolysis products in dependence on the features of the input brown coal were observed. Various types of brown coal were used for the pyrolysis tests differing mainly in the content of ash, sulphur and tar. Within the work mass balances of the incurred ...
The Accelerator Transmutation Waste System is under development at the Los Alamos National Laboratory. The goal is to perform an independent verification of the feasibility of actinide and long-lived fission product burning in this system. The authors' work is divided into five tasks: (a) production of an actinide and long-lived fission product cross section library from JEF 2.2; (b) simulation using MCNP and KENO IV Monte Carlo codes, of the Accelerator Transmutation Waste System configurations existing in literature; (c) validation of HETC Monte Carlo code (production of spallation source); (d) validation of the cross sections by comparison of Keff and reaction rate results, calculated with MNCP and KENO IV, with experimental benchmarks and intercomparison between the authors' calculations of a PWR unit cell and the computations carried out with various codes and cross section libraries (NEACRP critically group data); and (e) simulation of the final Los Alamos ...
Dual-fuel engines are modified diesel engines burning simultaneously two fuels inside the cylinder: a gaseous one, called the primary fuel and a liquid one, called the pilot fuel. The thermal efficiency of the dual-fuel engine and of the diesel engine are comparable; the level of emissions is lower compared to the diesel one. This article presents a new procedure for the combustion modeling in a LPG-diesel dual-fuel engine. The procedures deals with the ignition delay period and with the rate of heat release inside the cylinder. This procedure is validated using experimental data issued front a collaboration with the Indian Institute of Technology from Madras, India. The used engine is a single-cylinder one, air-cooled. The pilot fuel is direct injected inside the cylinder The engine was run at constant load and with different diesel substitutions, i.e. for different air to fuel ratios of the primary fuel-air mixture. The general error of the procedure is below ...
In March 2007 in-pile testing of LEU U-Mo full-size IRT type fuel elements was started in the MIR reactor. Four prototype fuel elements for Uzbekistan WWR SM reactor are being tested simultaneously - two of tube type design and two of pin type design. The dismountable irradiation devices were constructed for intermediate reloading and inspection of fuel elements during reactor testing. The objective of the test is to obtain the experimental results for determination of more reliable design and licensing fuel elements for conversion of the WWR SM reactor. The heat power of fuel elements is measured on-line by thermal balance method. The distribution of fission density and burn-up of uranium in the volume of elements are calculated by using the MIR reactor MCU code (Monte-Carlo) model. In this paper the design of fuel elements, the technique, main parameters and preliminary results are described. (author)
We obtained the ratios of {sup 134}Cs/{sup 137}Cs and {sup 154}Eu/{sup 137}Cs in spent PWR fuels with gamma scanning equipment of irradiated material examination facility. The fuel segments, of which the burn-up is about 40 GWD/MTU and its cooling time is 8.4 years, are prepared in Post Irradiated Examination Facility and transported to IMEF. By considering of multi-peaks of {sup 134}Cs and {sup 154}Eu, we obtained the relative efficiency of the gamma scanning system as a function of energy. And finally we obtained the number ratios of radioactive nuclides in 72 fuel pellets, radioactive {sup 134}Cs/{sup 137}Cs and {sup 154}Eu/{sup 137}Cs. (author). 4 refs., 27 tabs., 28 figs.
We obtained the ratios of "1"3"4Cs/"1"3"7Cs and "1"5"4Eu/"1"3"7Cs in spent PWR fuels with gamma scanning equipment of irradiated material examination facility. The fuel segments, of which the burn-up is about 40 GWD/MTU and its cooling time is 8.4 years, are prepared in Post Irradiated Examination Facility and transported to IMEF. By considering of multi-peaks of "1"3"4Cs and "1"5"4Eu, we obtained the relative efficiency of the gamma scanning system as a function of energy. And finally we obtained the number ratios of radioactive nuclides in 72 fuel pellets, radioactive "1"3"4Cs/"1"3"7Cs and "1"5"4Eu/"1"3"7Cs. (author). 4 refs., 27 tabs., 28 figs.
The investigation of various Two-Stage Liquefaction (TSL) process configurations was conducted at the Wilsonville Advanced Coal Liquefaction R D Facility between July 1982 and September 1986. The facility combines three process units. There are the liquefaction unit, either thermal (TLU) or catalytic, for the dissolution of coal, the Critical Solvent Deashing unit (CSD) for the separation of ash and undissolved coal, and a catalytic hydrogenation unit (HTR) for product upgrading and recycle process solvent replenishment. The various TSL process configurations were created by changing the process sequence of these three units and by recycling hydrotreated solvents between the units. This report presents a description of the TSL configurations investigated and an analysis of the operating and performance data from the period of study. Illinois No. 6 Burning Star Mine coal Wyodak Clovis Point Mine coal were processed. Cobalt-molybdenum and disposable iron-oxide ...
We demonstrate that a massive asymptotic giant branch (AGB) star is a good candidate as the main source of short-lived radionuclides in the early solar system. Recent identification of massive (4-8 solar masses) AGB stars in the Galaxy, which are both lithium- and rubidium-rich, demonstrates that these stars experience proton captures at the base of the convective envelope (hot bottom burning), together with high-neutron density nucleosynthesis with 22Ne as a neutron source in the He shell and efficient dredge-up of the processed material. A model of a 6.5 solar masses star of solar metallicity can simultaneously match the abundances of 26Al, 41Ca, 60Fe, and 107Pd inferred to have been present in the solar nebula by using a dilution factor of 1 part of AGB material per 300 parts of original solar nebula material, and taking into account a time interval between injection of the short-lived nuclides and consolidation of the first meteorites equal to 0.53 Myr. Such a ...
The properties of the highest velocity ejecta of normal Type Ia supernovae (SNe Ia) are studied via models of very early optical spectra of 6 SNe. At epochs earlier than 1 week before maximum, SNe with a rapidly evolving Si II 6355 line velocity (HVG) have a larger photospheric velocity than SNe with a slowly evolving Si II 6355 line velocity (LVG). Since the two groups have comparable luminosities, the temperature at the photosphere is higher in LVG SNe. This explains the different overall spectral appearance of HVG and LVG SNe. However, the variation of the Ca II and Si II absorptions at the highest velocities (v >~ 20,000 km/s) suggests that additional factors, such as asphericity or different abundances in the progenitor white dwarf, affect the outermost layers. The C II 6578 line is marginally detected in 3 LVG SNe, suggesting that LVG undergo less intense burning. The carbon mass fraction is small, only less than 0.01 near the photosphere, so that he mass ...
Results are presented from studies on the quality of cast parts made by counterpressure casting of high-strength aluminum alloy AMKh-605, and Al-Cu-Mn-Cr alloys (5.6-6.4% Cu, 0.25-0.55% Mn, 0.20-0.55% Cr, 0.20-0.45% Ti, 0.08-0.25% Zr, less than or equal to0.25% Fe, less than or equal to0.25% Si, less than or equal to0.05% Mg). Chill castings were heat treated by quenching from 450/sup 0/C (20 hours) in water, aging at 160/sup 0/C for five hours with cooling in air. Fractograms of tensile specimens are presented. Scanning electron microscopy allows an ambiguous determination of the cause of failure of a part, be it at initial crystallization crack defects or burns, and also allows a relationship to be established between structure and mechanical properties.
We improve the steady-state ab initio laser theory (SALT) of Tureci et al. by expressing its fundamental self-consistent equation in a basis set of threshold constant flux states that contains the exact threshold lasing mode. For cavities with non-uniform index and/or non-uniform gain, the new basis set allows the steady-state lasing properties to be computed with much greater efficiency. This formulation of the SALT can be solved in the single-pole approximation, which gives the intensities and thresholds, including the effects of nonlinear hole-burning interactions to all orders, with negligible computational effort. The approximation yields a number of analytic predictions, including a "gain-clamping" transition at which strong modal interactions suppress all higher modes. We show that the single-pole approximation agrees well with exact SALT calculations, particularly for high-Q cavities. Within this range of validity, it provides an extraordinarily efficient ...
The hazards of smoking in relation to lung cancer can never be over emphasized. In recent times shortly after Ebonyi State was created in 1996, the capital territory has increasingly been polluted by either quarry operators, motorcycle (Okada) riders or reckless cigarette smokers and bush burning. To investigate the havoc caused by all these on people, questionnaire was distributed among smokers and non smokers in various areas of specialization and habitations. In measuring the significance of association and the degree of association, a chi2 test and odds ratio method of analysis was employed. The result of the analysis showed that non-smokers do suffer lung cancer. It also revealed that the chances of a smoker to have lung cancer is 1.765 times higher than that of a non-smoker. Analysis also showed that lung cancer depends on age of smokers. It was later discovered that middle aged population are mostly affected, by the reason of chi2 partitioning. This research ...
Human beings are confronted with another grievous disaster - coal fire. The monitoring on underground coal bed combustion relied on drilling supervising in the past, but this method is not good. By taking the coal fire of Gulaben mine in Inner Mongolia Autonomous Region as an example, the monitoring methods of underground coal bed combustion were explored based on the hyperspectra and high-resolution remote sensing technology. By employing the OMIS imaging apparatus developed by Shanghai Institute of Technical Physics of Chinese Academy of Sciences, the airborne hyperspectral images and the characteristic spectra of different types were obtained and the temperature was measured synchronously on the ground. Then according to the correlation of DN value of the thermal infrared band and surface temperature, the image information was processed, the spectral features were analyzed, and the surface temperature retrieval model was built. Finally, by hyperspectral imagery radiation temperature ...
This Phase IV Remedial Design/Remedial Action Work Plan addresses the remediation of areas with the potential for UXO at the Idaho National Laboratory. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. Five areas within the Naval Proving Ground that are known to contain UXO include the Naval Ordnance Disposal Area, the Mass Detonation Area, the Experimental Field Station, The Rail Car Explosion Area, and the Land Mine Fuze Burn Area. The Phase IV remedial action will be concentrated in these five areas. For other areas, such as the Arco High-Altitude Bombing Range and the Twin Buttes Bombing Range, ordnance has largely consisted of sand-filled practice bombs that do not pose an explosion risk. Ordnance encountered in these areas will be addressed under the Phase I Operations and Maintenance Plan that allows for the recovery and disposal of ordnance that poses an imminent risk to human ...
The world fusion program has advanced to the stage where it is appropriate to construct a number of devices for the purpose of burning DT fuel. In these next-generation experiments, the expected flux and fluence of 14 MeV neutrons and associated gamma rays will pose a significant challenge to the operation and diagnostics of the fusion device. Radiation effects include structural damage to materials such as vacuum windows and seals, modifications to electrical properties such as electrical conductivity and dielectric strength and impaired optical properties such as reduced transparency and luminescence of windows and fiber optics during irradiation. In preparation for construction and operation of these new facilities, the fusion diagnostics community needs to work with materials scientists to develop a better understanding of radiation effects, and to undertake a testing program aimed at developing workable solutions for this multi-faceted problem. A unique ...
Fuelwood shortages and potential shortages are widespread throughout the developing world, and are becoming increasingly more prevalent because of the clearing of land for subsistence and plantation agriculture, excessive and inefficient commercial timber harvesting for domestic and export construction, and charcoal production to meet rising urban demands. Further, the environmental and socioeconomic consequences of the resulting deforestation are both pervasive and complex. This report focuses on the substitution of coal briquettes for fuelwood. Although substantial adverse health effects could be expected from burning non-anthracite coal or coal briquettes, a well-developed technique, carbonization, exists to convert coal to a safer form for combustion. The costs associated with briquetting and carbonizing coal indicate that ''smokeless'' coal briquettes can be produced at costs competitive with fuelwood and charcoal. The US ...
The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to proceed. The process has been successfully demonstrated on a pilot-scale as a method of ...
Technical developments in the construction of high power accelerators have created new research activities on accelerator-driven transmutation technologies (ADTT) with main applications for energy production and nuclear waste transmutation. The on-going research was reported and discussed at the conference. The studies of energy production based on ADTT indicate possible important advantages compared to the present nuclear power reactors. Natural Uranium or Thorium is burned in a subcritical reactor with or without simultaneous incineration and transmutation of nuclear waste. High level radioactive wastes and weapons Plutonium constitute an environmental and proliferation problem. Studies were reported on the possibilities to use ADTT to considerably shorten the life-time and reduce the amount of long-lived radioactive waste in order to decrease the volumes needed for long-term geologic deposition. A panel discussed the ADTT impact on nuclear waste disposal, ...
This invention relates with a pot-type catalyst carrier which excels as a catalyst carrier when such heavy oils as ordinary pressure distillation residue, oil sand oil, and shale oil are decomposed or treated by hydrogenation. The conventional pot-type carrier is produced by dropping a small drop of a slurry (containing a catalyst component) onto a particle bed and drying it. But the demerit is a large particle size and less catalyst activity or strength. In this invention, a mixture of such carrier components as allophane, red mud, bauxite and latellite, etc.. 60 - 80 weight parts. and a binder 20 - 40 weight parts is added with water to form a slurry of 10 - 30 weight% solid concentration. Slurry is wet-crushed to make the average particle size 0.6 - 2.0 micron, then spray-dried and burned to obtain a pot-type catalyst carrier with average particle size 30 - 200 micron and abrasion index below 10. This catalyst showed high yield of kerosene and light oil in the ...
The analysis described demonstrates the use of benefit/cost sensitivity analysis in examining the wide range of potential damages and savings associated with converting oil-fired electric utility boilers to burn coal in Florida. This model, for the first time incorporates, in quantitative terms, environmental economic externalities into a benefit/cost ratio sensitivity analysis framework. Five different dose-response estimates of morbidity and mortality costs, property devaluation, and willing-to-pay estimates are used in combination with four acid rain dose-response models to estimate the net present worth of externality costs. The model estimates the net present worth of benefits by incorporating into a dynamic framework all relevant construction, O + M, and fuel costs of converting an electrical generation facility from using oil to coal. These benefits of fuel savings are then weighted against various combinations of externality costs associated with increased ...
Tests with a 61 cm diameter fluidized-bed combustor revealed that raw cotton gin trash could be efficiently burned while satisfying Federal standards for particulate emissions. Certain chemicals within cotton gin trash zone can cause slagging or caking of ash and bed particles in the combustion zone. They can also corrode and accumulate on the heat recovery equipment. These problems are not considered insurmountable and methods of control are being studied. Raw cotton gin trash was also converted into a low Btu gas using fluidized-bed technology. Tests with a 30 cm diameter gasifier revealed that raw gin trash could be converted to a combustible gas, containing carbon monoxide and hydrogen. The heating value of the gas ranged from 3.65 to 5.29 MJ/m3 and about 50 percent of the heat value of the raw trash was converted to combustible gases. Economic analyses have shown that these techniques can be economically competitive with present fuels in specific situations.
The authors present arguments against nuclear energy and pro renewable energy sources. Thus, the water used in Uranium mining and primary ore processing becomes contaminated in long lived radioisotopes and so a threat for local ecosystems and communities. Then, during the fabrication, enrichment, and handling of nuclear fuel the workers are exposed to radiations and dangerous accidental radioactive leaks can occur. But, by far, the most menacing aspect of nuclear power exploitation remains the human errors in operating the nuclear plants which can result in major accidents like that from Chernobyl which spread radioactivity all over the Europe. The equipment used in nuclear facilities which is highly contaminated as well as the burned fuel implies transportation and long term storage which also present high risks. The major advantage of the nuclear energy consists in its very low environment impact and its null contribution to the greenhouse effect. In contrast, ...
In 1970, the Federal Power Commission predicted a fall from 46% to 27% in 1990 as a result of predicted increases in the use of nuclear power. Today, the Department of Energy expects coal to supply about 50% of electricity generation in 1990. About one-eighth of the world's annual hard coal production is used to make electricity in the United States. Power stations in the country used more coal in 1979 than was produced in the whole Western Europe that year. These 405,000,000 tons of coal equivalent were burned in 1257 individual utilities with an aggregate capacity of 235,000 megawatts. There are coal-fired power plants in 43 of the 50 states. Four factors will be most important in shaping the future development of coal-based electricity: prices, conservation, environmental regulations, and national security. The price differential between coal and oil has now reached a level where it is much more economic for a United States electric utility to build and ...
This report is an assessment of emission-control costs for municipal-waste combustors (MWCs). The details of the cost estimates, including their development, components, and cost premises, are addressed. A model-plant approach was used in the sizing and costing of the emission control systems. Due to differences in the feed-waste characteristics, combustion parameters, and emissions, separate cost estimates were required for mass burning (MB), modular (MOD), refuse-derived fuel (RDF), and fluid-bed combustion (FBC) type furnaces. Cost estimates were developed for control of particulate matter (PM) emissions only and for control of both acid gas and PM emissions from the MWC model plants. Controlled PM emission levels of 0.03, 0.02, and 0.01 gr/dscf, corrected to 12% CO/sub 2/, and 90 and 70% reductions of HC1 and SO2, respectively, were used to develop the control cost estimates. Costs were developed using the cost information received from a number of ...
A flexible and computationally economical model of the internal combustion engine was developed for use on large digital computer systems. It is based on a system of ordinary differential equations for cylinder-averaged properties. The computer program is capable of multicycle calculations, with some parameters varying from cycle to cycle, and has restart capabilities. It can accommodate a broad spectrum of reactants, permits changes in physical properties, and offers a wide selection of alternative modeling functions without any reprogramming. It readily adapts to the amount of information available in a particular case because the model is in fact a hierarchy of five models. The models range from a simple model requiring only thermodynamic properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. Among its many features the model includes heat transfer, valve timing, supercharging, motoring, finite ...
A three-dimensional mathematical model has been developed as a tool for furnace structure design and operation conditions optimization when the straw combustion is in oxygen-enriched or conventional air atmospheres. Mathematical methods have been used based on a combination of FLIC (A fluid Dynamic Incinerator Code) code for the in-bed incineration and commercial software FLUENT for the over-bed combustion. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressures and temperatures, which is reflected by very low residual amounts of organic combustion by-products in the bottom ash and flue gas of the straw-fired boiler unit. The predictions indicated that the maximum combustion temperature is around 1500 K, CO emission is 201 vppm and O{sub 2} concentration is about 6.9 vol% at furnace exit, and it is shown that mathematical models can serve as a reliable tool for detailed analysis of straw combustion processes in the packed-bed ...
The two-dimensional Eulerian hydrodynamic code 2DE, with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities into explosives, initiated by a low-velocity jet, are significantly less than for non-reactive solids ...
The two-dimensional Eulerian hydrodynamic code 2DE with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities into explosives, initiated by a low-velocity jet, are significantly less than for non-reactive solids of ...
The fast breeder test reactor at Kalpakkam has completed nearly 25 years of operation and is now operating at 18 MWt capacity with 46 fuel subassemblies (FSA) in the core consisting of 27 Mark-I (70% PuC + 30% UC), 13 Mark-II (55% PuC + 45% UC) and 6 MOX (44% PuO_2 + 56% UO_2) and one test PFBR FSA. Post Irradiation Examination (PIE) campaigns on FSAs at different burnup levels has provided valuable information about the irradiation behavior of the carbide fuel. This paper gives a summary of the irradiation performance of the carbide fuel evaluated through some of the investigations such as neutron radiography, x-radiography, gamma scanning, fission gas analysis and ceramography. Burnup of the carbide fuel could be enhanced from the initial design burnup limit of 50 GWd/t to 165 GWd/through systematic PIE. (author)
The processes controlling total carbon (C) storage and release from the terrestrial biosphere are still poorly quantified. We conclude from analysis of paleodata and climatebiome model output that terrestrial C exchanges since the last glacial maximum (LGM) were dominated by slow processes of C sequestration in soils, possibly modified by C starvation and reduced water use efficiency of trees during the LGM. In contrast, future C cycling will be dominated by human activities, not only from increasing C release with burning of fossil fuels, and but also from indirect effects which increase C storage in the terrestrial biosphere and decrease C storage in the biosphere. Comparison of the positive and negative C flux processes involved suggests that if the C sequestration processes are important, they likely will be so during the next few decades, gradually being counteracted by the C release processes. (Copyright (c) l993 Kluwer Academic Publishers.)
In response to the Clean Coal II solicitation, Bethlehem Steel Corporation (BSC) submitted a proposal to the DOE in May 1988. The proposal submitted by BSC describes a Unique integration of commercial technologies developed by Davy/Still Otto to clean coke oven gas being produced at its Sparrows Point, Maryland steel plant. This innovative coke oven gas cleaning system combines secondary gas cooling with hydrogen sulfide and ammonia removal, hydrogen sulfide and ammonia recovery, ammonia destruction and sulfur recovery to produce a cleaner fuel gas for plant use. The primary environmental benefit associated with employing this innovative coke oven gas cleaning system is realized when the fuel gas is burned within the steel plant. Emissions of sulfur dioxide are reduced by more than 60 percent. The removal, recovery and destruction of ammonia eliminates the disposal problems associated with an unmarketable ammonium sulfate by-product. Significant reduction in ...
Elevated pH operation to the pH value of 7.3 at 285degC is known to be effective for the reduction of radiation source in the primary water system of PWRs. A research project was started in 1989 and concluded in 1996 to study and verify the optimum pH and/or Li concentration from the viewpoint of radiation source reduction and materials integrity under improved water chemistry. This research project is sponsored by the Ministry of International Trade and Industries (MITI) in Japan and has two programs; high pH and high Li. The high Li program was conducted to establish the optimum Li concentration for the high boron concentration region (1100 - 1800 ppm) of the high burn up operation. In this paper, we shall discuss radiation source behavior under high pH conditions and PWSCC (Primary Water Stress Corrosion Cracking) susceptibility of materials with change of primary water chemistry conditions and the improved water chemistry control based on these tests results. ...
author.The existing management of hospital waste in Lebanon currently poses both an environmental hazard as well as a public health risk. This is due mainly to lack of legislation, information and modern treatment and disposal facilities designed for this purpose. A nation-wide questionnaire survey was conducted to asses the status of hospital waste management. The study started from October 1997 till August 1998. We found that 75% of the surveyed hospitals completely ignore their total waste quantity: 73% of hospitals surveyed practice segregation at source of infectious, pathological, sharps and pharmaceuticals; more than 40% dispose of their hospital risk wastes through the municipality waste disposal, 24% by burning in open fires, 14% by on-site hospital incinerators, 11% in on-site dumping, 8% handled by a private contractor and 1% in uncontrolled landfill. We conclude that with some exceptions, the hospital waste management situation in Lebanon is very far ...
The objective of the current research in coal liquefaction is to produce a synthetic crude from coal at a cost lower than $30.00 per barrel (Task A). A second objective is to produce a fuel which is low in aromatics, yet of sufficiently high octane number for use in the gasoline-burning transportation vehicles of today. To meet this second objective, research was proposed for conversion of the highly-aromatic liquid product from coal conversion to a product high in isoparaffins, which compounds in the gasoline range exhibit a high octane number (Task B). Experimental coal liquefaction studies conducted in a batch microreactor in the laboratory have demonstrated potential for high conversions of coal to liquids with low yields of hydrocarbon (HC) gases, hence small consumption of hydrogen in the primary liquefaction step. Ratios of liquids/HC gases as high as 30/1, at liquid yields as high as 82% of the coal by weight, have been achieved. The principal objective of ...
A statistical survey is conducted of air pollution in the city of Rome (Italy) due to conventional building space heating systems burning fossil fuels. The survey identifies the annual consumption of the different fuels and the relative amounts of the various pollutants released into the atmosphere by the heating plants, e.g., sulfur and nitrogen oxides, carbon monoxide, etc. Comparisons are then made between the ratios of urban heating plant air pollutants produced per tonne of fuel employed and those for ENEL (Italian National Electricity Board) coal, oil and natural gas fired power plants, in order to demonstrate the better environmental performances of the utility operated energy plants. The building space heating system energy consumption and pollution data are then used in a cost benefit analysis favouring the retrofitting of conventional heating systems with heat pump systems to obtain substantial reductions in energy consumption, heating bills and urban air ...
The application of foam in dealing with underground fire is well known due to its smothering action by cutting off air feed to burning fuel as well as acting as coolant. Besides plugging air feed to fire, water could be virtually reached to the fire affected areas much beyond the jet range as underground galleries with low roof restrict jet range of water. This method also enables a closer approach of a fire fighting team by isolating the toxic gases and smoke with a foam plug. The paper describes the development of high expansion foam composition and its application technology in order that foam plug method can be suitably utilized for combating mine fires in India. Three compositions were recommended for generation of high expansion foam: (a) 0.5% sodium/ammonium lauryl sulphate, 0.15 to 0.2% sodium carboxy methyl cellulose, 0.1% booster; (b) 0.5% sodium/ammonium lauryl sulfate, 0.12 to 0.15% alkaline solution of gum arabic, 0.1 to 0.2% ferrous gluconate; and (c) ...
A survey has been made in relation with the improvement project intended of energy conservation, and reduction of global warming gas emission at the Bobovdol thermal power plant located in the suburb of Sofia, the capital of the Republic of Bulgaria. The existing Bobovdol power plant having a total capacity of 630 MW with three generators is a coal burning thermal power plant having been used already for 23 to 27 years, hence over-aged. The survey has discussed an improvement project of scrap-and-build type to make the plant a high-efficiency gas combined cycle power plant using gas turbines. The project calls for building 210-MW gas combined power generation facilities having 70-MW gas turbines, one each in three stages in 2007, 2012 and 2017. As a result of the discussions, the fuel consumption reducing rate was found to reach 37.99%, whereas the cumulative energy saving quantity in 41 years will reach 16.37 million tons of fuel oil equivalent. In addition, the ...
This paper reports on an experimental investigation of premixed methane/air combustion stabilized within a reticulated partially stabilized zirconia foam burner that was performed. A flame holder was used to extend the stability range to allow a stable flame to be maintained for a variety of flow rate and equivalence ratio combinations. The stability range, temperature distributions, and emissions were examined over a range of equivalence ratios and flow rates. The flame was found to be axisymmetric for all conditions in which the reactants were sufficiently well mixed and the flow distribution was sufficiently uniform. Burning speeds were measured that were well in excess of the laminar flame speed. The axial temperature distribution (measured around the burner annulus) in the postflame zone was found to be relatively insensitive to flow rate but dependent upon the burner core length. Very low concentrations of NO_x were found for fuel/air equivalence ratios of ...
The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of {sup 60}Co {gamma}-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H{sub 2}) = 0.100 d{sup -1.6}. The G-values of oxygen and nitrogen releases were also determined. (author)
The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).
The work reported is to evaluate two alternative resource recovery systems which would produce a fuel or an energy product (steam) for sale to an industrial plant. The first alternative is a refuse derived fuel (RDF) production facility which would process waste to produce fuel for sale to the plant. The RDF would be co-fired with coal in new boilers. The second alternative is a mass burn steam generation facility which would produce high pressure superheated steam for sale. The steam would be used by the plant to cogenerate electricity and for the process. Conceptual designs are developed for each alternative to form the basis of estimates of capital and operating costs and potential energy revenues. Operating requirements are developed for both alternatives. An assessment is made of the impact of both alternatives on the environment, and it is concluded that the impact of either alternative will be negligible. Order of magnitude estimates are made of capital and ...
Flame lengths inside circular tubes, using an (in-shot) atmospheric burner design commonly found in gas-fired residential furnaces were visually observed for natural gas and air under various operating conditions. The flame length data were reduced into dimensionless flame lengths, which were shown to be linearly proportional to the Peclet number of the fuel and air mixture. The dimensionless flame length dependence reported does not scale according to the classical flame models: pre-mixed (laminar) flame or diffusion flame. Instead, the flame length dependence was found to scale with the fuel burn speed, gas/mixture properties (evaluated at the adiabatic flame temperature), and flow parameters. Currently, this is the only flame length study available for the standard atmospheric burner designs commonly used in residential heating products. The results and data reduction provide an easy method to compute flame length penetrations inside circular tubes for the ...
This study tried to reduce NO{sub x} and particulate emissions simultaneously in a high speed direct-injection diesel engine. Fuel-rich combustion was used to reduce NO{sub x} emission at initial combustion stage and high turbulence combustion was used to reduce particulate emission at diffusion combustion stage. Experiments were carried out to investigate the effects of high squish combustion chambers with small throat on combustion process and exhaust emissions. Results showed that in the high squish combustion chamber, both NO{sub x} and particulate emissions reduced with retarded injection timing. Endoscopic high speed photography was employed to analyze experimental results. In the original combustion chamber at the early combustion stage, the high luminosity flame tended to spread out of the cavity. Fuel-rich mixture burned slowly over the piston crown. In the high squish combustion chamber, flame rotated violently around the bowl. Fuel-rich mixture was kept ...
For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the gasification. However, their catalytic effect is related with chemical ...
The use of concentrated solar energy for co-producing Zn and synthesis gas from Zn O and natural gas upgrades the calorific value of the initial reactants by 39% and, when compared to the traditional carbothermic reduction of Zn O, has the potential of reducing CO{sub 2} emissions by up to 78%. An economic assessment for an industrial thermochemical plant, 30 to 51 MW solar input, indicates that the cost of solar production of zinc ranges between 89-133 $/t (excluding the cost of Zn O feed and credit for pollution abatement), and thus might be competitive with conventional fossil-fuel-based processes at current fuel prices. The cost of solar H{sub 2}, produced by splitting water with zinc, is estimated to be in the range 0.10-0.14 $/kWh, and it is a favorable long term prospect once the cost of energy will account for the environmental externalities from fossil fuel burning such as the costs for CO{sub 2} mitigation and pollution abatement. (author) 1 fig., 2 ...
A fluidized bed combustor of 0.146 m diameter and 1 m length was fabricated from stainless steel to burn olive cake. Initially, and in order to obtain fluidization, the system was operated under cold conditions using a sand with particle size in the range of 500 to 710 microns. The continuous combustion experiments were carried out under controlled conditions, such that the effects of bed temperature, olive cake feed rate, fluidization velocity, and particle size on combustion efficiency and flue gas composition were investigated. It was found that the combustion efficiency decreases with the bed temperature, fluidization velocity, and the feed rate, while it increases with the particle size used. Further, the gas products analysis carried out using a gas chromatography analyzer have shown a nonmeasured amount of SO2, and small amounts of CO. Finally, the temperature distribution along the bed indicated that the temperature throughout the bed is fairly uniform, ...
This paper describes the design and feasibility tests of a 570 mm bore 4 stroke low pressure (L.P.) dual fuel engine rated at 20.9 bar BMEP meant for the propulsion of LNG carriers. The basic design features which are to be in accordance with classification societies safety rules are described: individual electro hydraulic valves located in the air manifold ducts, pilot injection, monitoring system etc. The engine capability to burn variable liquid/gas fuel proportions have been investigated with diesel oil and heavy fuel and possible running zones are defined. This ensures the possibility of the engine to cope with the different boil off gas quantity emanating from the ship`s tank during her loaded - and ballast - journeys. With the very lean setting of this engine, no adverse influence of the high ash lube-oil additives were found during the tests. Further tests are necessary to confirm that possible more significant fouling of the combustion chamber is still ...
Burnable poisons are used in nuclear reactors to produce a more level distribution of power in the reactor core and to reduce to necessity for a large control system. An ideal burnable poison would burn at the same rate as the fuel. In this study, separation of neutron-absorbing isotopes was investigated in order to eliminate isotopes that remain as absorbers at the end of fuel life, thus reducing useful fuel life. The isotopes Gd-157, Dy-164, and Er-167 were found to have desirable properties. These isotopes were separated from naturally occurring elements by means of plasma separation to evaluate feasibility and cost. It was found that pure Gd-157 could save approximately $6 million at the end of four years. However, the cost of separation, using the existing facility, made separation cost- ineffective. Using a magnet with three times the field strength is expected to reduce the cost by a factor of ten, making isotopically separated burnable poisons a favorable ...
A survey to assess the techniques used to control occupational exposure to formaldehyde (50000) and methanol (67561) was conducted at the E. I. DuPont de Nemours and Company (SIC-2869) formaldehyde production unit, Linden, New Jersey, in October 1982. Exposure concentrations were reduced primarily by the use of a process that was completely enclosed except for process sampling, methanol unloading, and formaldehyde discharge points. Local and area exhaust ventilation, and work practices were also used to control exposures. Formaldehyde concentrations in the absorber area were controlled by burning the exit gases in an afterburner and discharging them high above the ground. Analysis of area and breathing zone samples showed methanol and formaldehyde concentrations below the OSHA limits of 200 and 3 parts per million, respectively. The authors conclude that workers are not overexposed to either methanol or formaldehyde on a short or long term basis. Maintenance ...
In the framework of the development of burnup calculation method for commercial fast reactors, a sensitivity analysis was carried out to clarify the dependence of fuel burnup characteristics on nuclear data libraries (NDLs). The following NDLs were compared: JEF-2.2, ENDF/B-VI Release 5, JENDL-3.2 and JENDL-3.3. The NDL-dependence of material balance for main heavy metal nuclides ("2"3"5U, "2"3"8U, "2"3"9Pu, "2"4"0Pu and "2"4"1Pu) was small, since the number densities at the end of one-cycle burnup did not change over 1 or 2% among the above-mentioned libraries. Relatively large differences were found for minor actinide nuclides, especially for "2"3"6U, "2"3"7Np, "2"4"2"mAm, "2"4"3Am and curium isotopes. The number densities for these nuclides after burning up showed remarkable NDL-dependence over 5% through 50%. A burnup sensitivity analysis system based on the generalized perturbation theory enabled us to find out quantitatively the causative nuclides and ...
At the Tokai Research Establishment of Japan Atomic Energy Research Institute, the radioactive solid waste incineration unit with a capacity of 100 kg/h was installed in 1979, since then the unit has been routinly operated. An off-gas cleaning system of the unit consists mainly of a primary and secondary ceramic filters, a heat resistant HEPA filter and a scrubber. A series of hot test was carried out to examine the docontamination performance for radionuclides in the off-gas cleaning system. In the test, simulated wastes contaminated with a known quantity of radionuclides were burned in the unit, and radioactive concentrations in the off-gas were measured. And then, the following data were obtained: a retention factor of radionuclides in a furnace and a decontamination factor for radionuclides in each of off-gas cleaning components. And also overall decontamination factors, defined as the ratio of radioactivities input to the furnace to radioactivities passed ...
A total of 10 samples disks of 2024-T3 aluminum and 4130 ferrous steel were exposed to rocket-triggered lightning currents at the Kennedy Space Center test site in Florida during the summer of 1990. The experimental configuration was arranged so that the samples were not exposed to the preliminary streamer, wire-burn, or following currents that are associated with an upward-initiated rocket-triggered flash but which are a typical of naturally initiated lightning. Return-stroke currents and continuing currents actually attaching to the sample were measured, augmented by close-up video recordings of approximately 3 feet of the channel above the sample and by 16-mm movies with 5-ms resolution. From these data it was possible to correlate individual damage spots with streamer, return-stroke, and continuing currents that produced them. Substantial penetration of 80-mil aluminum was produced by a continuing current of submedian amplitude and duration, and full ...
This report describes the 5 tasks to be covered under this project and compiles budget information. Task 1 is to establish a Plutonium Information Resource, which has been established in Amarillo, Texas. Task 2, Advisory Functions, coordinates studies and activities relating to the disposition of excess weapons-grade plutonium. Task 3, Environmental, Public Health, and Safety, supports soil remediation activities. Task 4, Education and Outreach, is supporting four programs: K--12 education improvement in science and math courses; Academic intervention to identify and encourage high ability high school and middle school students with potential to become scientists and engineers; Graduate education evaluation; and Public outreach programs. Task 5, Plutonium and other Materials Studies, is currently funding two projects for the disposition of high explosives: a feasibility study of burning a mixture of high explosives and other materials in a commercial coal-fired ...
The generation of fusion power from the Fast-Liner Reactor (FLR) concept envisages the implosion of a thin (3-mm) metallic cylinder (0.2-m radius by 0.2-m length) onto a preinjected plasma. This plasma would be heated to thermonuclear temperatures by adiabatic compression, pressure confinement would be provided by the liner inertia, and thermal insulation of the wall-confined plasma would be established by an embedded azimuthal magnetic field. A 2- to 3-mu s burn would follow the approx. 10"4 m/s radial implosion and would result in a thermonuclear yield equal to 10 to 15 times the energy initially invested into the liner kinetic energy. For implosions occurring once every 10 s a gross thermal power of 430 MWt would be generated. The results of a comprehensive systems study of both physics and technology (economics) optima are presented. Despite unresolved problems associated with both the physics and technology of the FLR, a conceptual power plant design is ...
Hydrogen is a potential alternative energy source and produced commercially by methane (natural gas) or LPG steam reforming, a process that requires high temperatures, which are produced by burning fossil fuels. However, since this process emits large amounts of CO_2, replacement of the combustion heat source with a nuclear heat source for 773-1173 K processes has been proposed in order to eliminate these CO_2 emissions. This paper proposes a novel method of low-temperature nuclear hydrogen production by reforming dimethyl ether (DME) with steam produced by a low-temperature nuclear reactor at about 573 K. The authors identified conditions that provide high hydrogen production fraction at low pressure and temperatures of about 523-573 K. By setting this low-temperature hydrogen production process at about 573K upstream from a turbine, it was found theoretically that the total energy utilization efficiency is about 50% and very high. By setting a turbine upstream of ...
Core-collapse supernovae are among Nature's most energetic events. They mark the end of massive star evolution and pollute the interstellar medium with the life-enabling ashes of thermonuclear burning. Despite their importance for the evolution of galaxies and life in the universe, the details of the core-collapse supernova explosion mechanism remain in the dark and pose a daunting computational challenge. We outline the multi-dimensional, multi-scale, and multi-physics nature of the core-collapse supernova problem and discuss computational strategies and requirements for its solution. Specifically, we highlight the axisymmetric (2D) radiation-MHD code VULCAN/2D and present results obtained from the first full-2D angle-dependent neutrino radiation-hydrodynamics simulations of the post-core-bounce supernova evolution. We then go on to discuss the new code Zelmani which is based on the open-source HPC Cactus framework and provides a scalable AMR approach for 3D fully ...
The feasibility of using hydrogen as the sole fuel in a direct injection diesel engine was investigated. An air cooled single cylinder Lister ST1 diesel engine was modified to operate as a low-heat-rejection engine for this study. Partially stabilized zirconia ceramic parts were used to shield the combustion space of the engine. Using a compression ratio of 17.9:1 and motoring the test engine at 21000 rpm, a maximum compression temperature of approximately 900 K was achieved. Under these operating conditions, all lubricants tested were found to burn. Lowering the speed to 1450 rpm and the compression ratio to 17.1, lubricant combustion and hot spots were successfully eliminated. The maximum compression temperature, when compression ignition of hydrogen was tried, was in the 800 K range. The corresponding ceramic surface temperature was estimated to reach 600-700 K. Only sporadic compression ignition of hydrogen was achievable. (author).
This report describes the combustion experiments performed using the SP Industry Calorimeter. In addition to measuring parameters such as heat release rate (HRR), mass loss rate, effective heat of combustion and smoke obscuration, considerable effort was put into the characterisation of the smoke gases in order to obtain a basis for evaluations of the toxic potency of the smoke. The materials studied were Nylon 66, polypropene, polystyrene (with and without fire retardant, respectively), PVC and chlorobenzene. A total of 19 large-scale, well ventilated combustions were carried out. The mass of sample burned ranged from 20 kg to 125 kg in an experiment. A procedure was designed for cleaning the smoke gas duct between experiments and was found to be effective. Measurements were carried out for the amounts of O{sub 2}, CO{sub 2}, CO, NO{sub x}, THC (unburned hydrocarbons), HCN, HCl, NH{sub 3} and individual organic compounds in the smoke. Adsorbents were used for the ...
In 1990, 176 million tonnes (mt) of air-traffic fuel was burned, which produced about 550 mt CO{sub 2}, 220 mt water, 3.5 mt NO{sub x} amd 0.18 mt SO{sub 2}. NO{sub x} emissions from air traffic may, by increasing ozone concentrations, be responsible for about 8% of global greenhouse warming. In the stratosphere NO{sub x} from aircraft is partly responsible for ozone depletion. With present technology 500 aircraft in the stratosphere would cause global ozone losses of 20%. Water vapour added by aircraft also contributes to global warming. In the form of ice crystals between 8 to 13 km above sea level, it acts as cirrus clouds. Probably the least damaging cruising altitude for aircraft is 9 km above sea level. Fuel consumption by aircraft is increasing. Air pollution abatement measures include substituting hydrogen fuel for kerosene, developing engines that emit less NO{sub x} and the introduction of internationally negotiated taxes on kerosene. 30 refs.
Further to a cost-benefit analysis of the various medium-term and long-term and H.L.W. storage possibilities, C.E.A. (French Atomic Energy Commission) and S.G.N. decided to develop an original dry storage process with natural convection cooling that offers many advantages: cut in the total investment and operating costs; high operating safety; natural convection cooling; existence of two containment barriers irrespective of the assumed clad conditions; flexible, modular and compact design. The process was first implemented in the so-called CASCAD Cadarache Facility (vault-type facility) constructed in Cadarache mainly to store fuel from Brennilis heavy water reactor. For the purpose, a large program was set up to develop and validate computer codes, in particular with the use of mockups. On the request of many clients, and owing to the outstanding operating results of the CASCAD Cadarache Facility, SGN was brought to adapt the process to the storage of other types of fuel: LWR, PWR, ...
Burner for feeding a solid and a liquid or gaseous fuel to a kiln comprises a central supply pipe for liquid or gas surrounded concentrically by a first pipe providing an annular passage through which primary air is supplied. Concentrically surrounding that pipe is a second pipe providing an annular channel for supply of solid fuel in carrier air stream. The outlet end of the first concentric pipe is closed by a plate fixed mounted at the pipe end and providing multiple nozzles having their axes parallel to the burner axis. The surface of the plate facing the burning zone provides a divergence opening for the central pipe while the inner surface is formed with helical teeth. These are engaged by complementary teeth mounted on the end of the central pipe which is rotatable and biased by springs so that the teeth are in engagement. Rotation of the pipe causes relative axial motion of the teeth to create tangential slots for admission of primary air into the central ...
This paper evaluates the two well-known final waste disposal methods, incineration and landfilling. In particular we compare the social cost of two best-available technologies using a point estimate based on private and environmental cost data for the Netherlands. Not only does our comparison allow for Waste-to-Energy incineration plants but for landfills as well. The data provide support for the widespread policy preference for incineration over landfilling only if the analysis is restricted to environmental costs alone and includes savings of both energy and material recovery. Gross private costs, however, are so much higher for incineration, that landfilling is the social cost minimizing option at the margin even in a densely populated country such as the Netherlands. Furthermore, we show that our result generalizes to other European countries and probably to the USA. Implications for waste policy are discussed as well. Proper treatment of and energy recovery from landfills seem to ...
Biological wound dressings sterilized with gamma radiation, such as amnion and pig skin, are a reality in Mexico. These tissues are currently processed in the tissue bank and sterilized in the Gamma Industrial Irradiation Plant; both facilities belong to the Instituto Nacional de Investigaciones Nucleares (ININ) (National Institute of Nuclear Research). With the strong support of the International Atomic Energy Agency, the bank was established at the ININ and the Mexican Ministry of Health issued its sanitary license on July 7, 1999. The Quality Management System of the bank was certified by ISO 9001:2000 on August 1, 2003; the scope of the system is 'Research, Development and Processing of Biological Tissues Sterilized with Gamma Radiation'. At present, more than 150 patients from 16 hospitals have been successfully treated with these tissues. This paper presents a brief description of the tissue processing, as well as the present Mexican clinical experience with children and adult ...
Heavy-duty trucks and buses are substantial contributors to the atmospheric oxides of nitrogen (NO_x) inventory, but prediction of their emissions in real use remains inchoate. Continuous emissions of NO_x were recorded from Chassis dynamometer testing of eight vehicles using a variety of transient cycles, including the Central Business District schedule. NO_x data were treated to account for sampling time lag and presented against instantaneous vehicle axle power. Data were repeatable from run to run and test schedule, but vehicle type and test cycle both influenced the instantaneous emissions rates. However, the resulting correlations may be used for mobile source NO_x contribution estimation when combined with vehicle activity data. The emissions data were also presented as NO_x/CO_2, which are valuable for comparison with remote sensing emissions data. The overall average ratio for all of the data considered was 0.0141, which corresponds to an emissions contribution of 0.0423 g of ...
A generic reactor model is used to examine the economic viability of electricity generation by magnetic fusion. The simple model uses components which are representative of those used in previous reactor studies of deuterium-tritium burning tokamaks, stellarators, bumpy tori, reverse field pinches and tandem mirrors. Conservative costing assumptions are made. The generic reactor is not a tokamak but rather it is intended to emphasize what is common to all magnetic fusion reactors. The reactor uses a superconducting toroidal coil set to produce the dominant magnetic field. To this extent it is a less good approximation to systems, such as the reversed field pinch in which the main field is produced by a plasma current. The main output of the study is the cost of electricity as a function of the weight and size of the fusion core - blanket, shield, structure and coils. The model shows that a 1200 MW/sub e/ power plant with a fusion core weight of about 10,000 tonnes ...
The results of an experimental investigation of the performance of a small bore engine with a swirl chamber when operating as a dual fuel engine with commercial methane as the gaseous fuel were presented in this paper. The experiment involved using a 3-dimensional computational fluid dynamics model to predict the performance of the engine. A detailed chemical kinetics for the gaseous fuel component, consisting primarily of methane and a reduced detailed chemical kinetics for the diesel fuel while considering the turbulent combustion processes an associated performance of a dual fuel engine with a swirl chamber were incorporated in the simulation. The study experimentally and numerically investigated the effects of changes in the quantities of the liquid fuel pilot and gaseous fuels on the combustion processes, engine performance, cyclic variations, and emissions. The paper discussed the experimental approach and results. It also discussed the simulation of the dual fuel engine ...
The AFGD process as demonstrated by Pure Air at the Bailly Station offers a reliable and cost-effective means of achieving a high degree of SO{sub 2} emissions reduction when burning high-sulfur coals. Many innovative features have been successfully incorporated in this process, and it is ready for widespread commercial use. The system uses a single-loop cocurrent scrubbing process with in-situ oxidation to produce wallboard-grade gypsum instead of wet sludge. A novel wastewater evaporation system minimizes effluents. The advanced scrubbing process uses a common absorber to serve multiple boilers, thereby saving on capital through economies of scale. Major results of the project are: (1) SO{sub 2} removal of over 94 percent was achieved over the three-year demonstration period, with a system availability exceeding 99.5 percent; (2) a large, single absorber handled the combined flue gas of boilers generating 528 MWe of power, and no spares were required; (3) direct ...
A sequential port injection, lean-burn, fully electronically-controlled compressed natural gas (CNG)/diesel dual-fuel engine has been developed based on a turbo-charged and inter-cooled direct injection (D.I.) diesel engine. During the optimisation of engine overall performance, the effects of pilot diesel and premixed CNG/air mixture equivalence ratio on emissions (CO, HC, NO{sub x}, soot), knocking, misfire and fuel economy are studied. The rich and lean boundaries of the premixed CNG/air mixture versus engine load are also provided, considering the acceptable values of NO{sub x} and THC emissions, respectively. It is interesting to find that there is a critical amount of pilot diesel for each load and speed point, which proved to be the optimum amount of pilot fuel. Any decrease in the amount of pilot diesel from this optimum amount results in an increase of NO{sub x} emissions, because the premixed CNG/air mixture must be made richer, otherwise THC emissions ...