WorldWideScience
1

Calculation of ice accumulation rates in Antarctica over the last glacial cycle.  

Environmental Research Database

DescriptionRates of ice accumulation in Antarctica are not known well, yet they are fundamental to assessing the ice sheet mass balance. Past accumulation rates are less well defined. We are in a unique position to provide detailed accounts of accumulation in Antarctica. We will measure isochronous internal layering across the ice sheet, which can be readily identified in radar data that we hold. Internal layers will be traced to ice-cores (allowing dating) and across wide regions of the ice sheets. A nume [continued...

2006-01-08

2

Numerical testing of hypotheses for the recent thinning and acceleration of Greenland outlet glaciers  

Environmental Research Database

ObjectivesThe overall scientific aim of this project is, through development of an appropriate numerical modelling tool, to identify and investigate the mechanisms that control the current observed rapid thinning and acceleration of Greenland outlet glaciers and to investigate their likely future behaviour in the context of climate warming. This aim is addressed through the four major specific objectives below. These objectives build on each and therefore the order of priority is driven by the order in wh [continued...]DescriptionCurrently, the Greenland ice sheet is undergoing rapid changes in the coastal regions which have been attributed to a general warming trend to the regions climate over the last decade. Several of the narrow and fast flowing outlet glaciers that drain the ice sheet into the sea are observed to have accelerated their flow and thinned. For instance, Jakobshavn Isbrae on the West ...

2008-01-31

3

USA-ALASKA/KENAI PEN., LIMB, SNOW, ICE  

Science.gov (United States)

UNITED STATES OF AMERICA, ALASKA/KENAI PEN., LIMB, SNOW, ICE

2009-01-01

4

Present conditions in Greenland and the Kangerlussuaq area  

International Nuclear Information System (INIS)

Greenland is the world's largest island, with an area of 2.2 million square kilometres, 80 % of which is covered by the ice sheet. The climate is Arctic, but as Greenland stretches 2600 km from north to south, there is a huge variability in climate, with temperature decreasing from south to north. Due to the influence of oceanic currents, the west coast is slightly warmer than the east coast. Precipitation also decreases strongly from the south to the north, and also with distance from the coast. Kangerlussuaq is located in the dry, continental area of central west Greenland. The bedrock of Greenland is dominated by Precambrian gneisses, with sedimentary rocks occurring in some areas of East and North Greenland, and smaller areas of basalts. All of Greenland has been glaciated several times and has thus been eroded and shaped by the ice, as it still is at the ice margin. Soils are generally thin, and ...

5

Space Food and Nutrition pdf - Space Shuttle Experience - NASA  

Science.gov (United States)

Yellow cake with chocolate frosting. Dairy: Ice cream, chocolate. Ice cream, strawberry. Ice cream, vanilla. Yogurt, frozen ...

6

De-icing technologies: Introduction to Manitoba Hydro's use of ice melting and ice rolling technologies to remove ice from subtransmission and 115 kV transmission lines  

International Nuclear Information System (INIS)

Manitoba Hydro's Ice Storm Management Program to reduce ice damage to overhead power lines in the voltage range of 8 kV to 115 kV is described. Overhead power lines are de-iced either by AC ice melting, which involves placing a three-phase short at a calculated point, or ice rolling, which is a process of mechanically stripping ice from conductors. Direct current heating and underground distribution systems are also accepted prevention measures. Advantages and disadvantages of each of these methods of de-icing are reviewed. Material for this paper has been extracted from a workshop manual prepared for the 1993 and 1998 Ice Storm Management workshops organized by Manitoba Hydro through the Canadian Electrical Association. 1 ref.

1999-03-29

8

Tilt-a-Worlds: Effects of High Rates of Obliquity Change on the Habitability of Extrasolar Planets  

Science.gov (United States)

We explore the impact of obliquity variations on planetary habitability in hypothetical systems with high mutual inclination. For the hypothetical systems, we restrict our exploration to systems consisting of a solar-mass star, an Earth-mass planet at 1 AU, and 1 or 2 giant planets. We verify that these systems are stable for 108 years with N-body simulations. We then calculate the obliquity variations induced by the orbital architecture on the Earth-mass planets. We find that in some cases the spin axes can rotate through 360 degrees in as little as 10,000 years (John is that right? Can you look through the systems and find the most extreme case of obliquity variation?) Next, we run energy balance models (EBM) on the terrestrial planets to assess surface temperature and ice coverage on the planets' oceans. Finally, we explore differences in the outer edge of the habitable zone for planets with rapid obliquity variations. We run EBM simulations for a range of ...

2011-01-01

9

Freezing phenomena in ice-water systems  

Energy Technology Data Exchange (ETDEWEB)

The characteristics of solidification and melting are reviewed. The properties of water and ice and the phase diagram of water are discussed with special emphasis on ice density. A concise account of the freezing process and the Stefan problem is presented. To this end, the four stages of freezing are identified, supercooling, nucleation and the formation of dendritic ice, the growth of concentric rings of solid ice at 0{sup o}C and the final cooling of the solid ice are treated in some detail. The subject of bursting of pipes is given particular emphasis. Attention is drawn to a common misconception on pipe bursting and to misleading relationships for the computation of freezing time for ice blockage. Several current applications of melting and freezing systems are outlined. (author)

2002-09-01

10

An analysis of selected atmospheric icing events on test cables  

Energy Technology Data Exchange (ETDEWEB)

In cold countries, the design of transmission lines and communication networks requires the knowledge of ice loads on conductors. Atmospheric icing is a stochastic phenomenon and therefore probabilistic design is used more and more for structure icing analysis. For strength and reliability assessments, a data base on atmospheric icing is needed to characterize the distributions of ice load and corresponding meteorological parameters. A test site where icing is frequent is used to obtain field data on atmospheric icing. This test site is located on the Mt. Valin, near Chicoutimi, Quebec, Canada. The experimental installation is mainly composed of various instrumented but non-energized test cables, meteorological instruments, a data acquisition system, and a video recorder. Several types of icing events can produce large ...

1996-12-01

11

Behavior of ice covers subjected to large daily flow and level fluctuations  

Energy Technology Data Exchange (ETDEWEB)

The stability of a solid ice cover subjected to rapidly varying water levels and discharge was investigated. The support from the bank limits the stress in the ice cover and consequently bank contact must be maintained to ensure ice cover stability. An analysis was required of the stability of ice hinges, a flexible connection between a solid ice cover and the riverbank. Phase II and phase III of the research involved a field study of the Peace River, investigating the evolution of ice hinges with water level variation, from initial ice cover cracking parallel to the banks, to a fully developed hinge. A test program of midwinter discharge variations was undertaken to gather specific data and measurements of ice hinge link length, ice thickness, hinge joint behavior, riverbank geometry, and response ...

1984-11-01

12

Climatic change and river ice breakup  

Energy Technology Data Exchange (ETDEWEB)

An overview of climatic factors and impact relative to river ice engineering and science is presented. An explanation of the fundamentals of climatic change is followed by a review of direct and indirect climatic influences that govern river ice breakup and related trends. Known responses of river ice to climatic change and potential future changes to ice breakup processes are described along with the probable ecological and socio-economic consequences of these changes. Changes in engineering approaches to accommodate the present ice regime and predicted changes in climatic variables that affect river ice processes and reduce the vulnerability of infrastructure and ecosystems to climatic change are examined. Future research on the links between river ice and stream ecology is suggested to identify ecological concerns that may result from ...

2003-07-01

13

Respect distances. Rationale and means of computation  

Energy Technology Data Exchange (ETDEWEB)

Canisters with spent nuclear fuel can obviously not be located within deformation zones as this might jeopardise their long term mechanical stability and thereby constitute a potential hazard to the biosphere. Less apparent, but equally important, is the fact that earthquakes trigger reactivation, slip, of structures some distance from their hypocentres due to, among many other factors, stress redistribution. Fault slip across a deposition hole might damage the isolation capacity of the canister and thereby jeopardise the overall integrity of the barrier system. Therefore, the following question might be posed: What is the distance from a deformation zone beyond which a canister can be safely emplaced? This respect distance cannot be readily computed because, unknown future events aside, there are some complicated aspects that need to be addressed e.g. degree of conservatism, scale, our ability to model ice sheets and earthquakes, etc. In this ...

2004-12-01

14

GOCE, Satellite Gravimetry and Antarctic Mass Transports  

Science.gov (United States)

In 2009 the European Space Agency satellite mission GOCE (Gravity Field and Steady-State Ocean Circulation Explorer) was launched. Its objectives are the precise and detailed determination of the Earth's gravity field and geoid. Its core instrument, a three axis gravitational gradiometer, measures the gravity gradient components V xx , V yy , V zz and V xz (second-order derivatives of the gravity potential V) with high precision and V xy , V yz with low precision, all in the instrument reference frame. The long wavelength gravity field is recovered from the orbit, measured by GPS (Global Positioning System). Characteristic elements of the mission are precise star tracking, a Sun-synchronous and very low (260 km) orbit, angular control by magnetic torquing and an extremely stiff and thermally stable instrument environment. GOCE is complementary to GRACE (Gravity Recovery and Climate Experiment), another satellite gravity mission, launched in 2002. While GRACE is designed to ...

2011-03-01

15

River ice jams at bridges  

Energy Technology Data Exchange (ETDEWEB)

Ice jamming, known to cause high water levels at even moderate river flows, is described as both the main and least understood source of ice-related bridge damages. This paper describes a joint study by the New Brunswick Department of Transportation, the Department of the Environment, local governments, and the National Water Research Institute, designed to address problems associated with the interaction of ice jams and bridges. The study consists of collecting information at each of four sites in New Brunswick including: historical data on ice jam locations, causes, and water levels; channel bathymetry, width and slope within each study centred at the respective bridge; and documentation of ice conditions throughout the ice season, including measurement of ice cover thickness, observation of breakup mechanisms, times, causes, ...

2000-12-01

16

Divergence of AMP Deaminase in the Ice Worm Mesenchytraeus solifugus (Annelida, Clitellata, Enchytraeidae)  

UK PubMed Central (United Kingdom)

Glacier ice worms, Mesenchytraeus solifugus and related species, are the largest glacially obligate metazoans. As one component of cold temperature adaptation, ice worms maintain atypically...Full Text Available

17

Specification of the steel sheet for the 300 GeV magnet system  

CERN Document Server

Specification of the steel sheet for the 300 GeV magnet system

1971-01-01

18

Strategy for forecasting ice breakup and jamming: Saint John River, New Brunswick  

Energy Technology Data Exchange (ETDEWEB)

Development of a strategy for forecasting river ice breakup and jamming on the Saint John River in New Brunswick was described. Methods used to identify ice jam-prone areas by simple temperature-based methods to fairly complex computer models using site specific data, were summarized. Recent technological advances in developing forecasts, including the NWRI probe for remotely measuring ice jam thickness, the RIVJAM model for determining stages upstream of an ice jam, and computational procedures for estimating the thrust exerted by ice jams against bridges, were also reviewed. Criteria and recommendations for river ice breakup and ice jamming for the Saint John River were provided. (Abstract only).

1995-12-31

19

IV&V Cost Estimation-A Joint NASA & Navy  

Science.gov (United States)

Possible ICE Tools Relationship. within a Business Model ... Established a Joint IV&V Cost Estimating (ICE) Team comprised of Personnel from NASA, ...

20

Cook Inlet and Kenai Peninsula, Alaska ESI: ICE (Ice Extent Lines)  

Science.gov (United States)

... layer, part of the larger Cook Inlet and Kenai Peninsula ESI database, for additional hydrologic information. This ... ...

21

Behavior of ice covers subjected to large daily flow and level fluctuations  

Energy Technology Data Exchange (ETDEWEB)

The stability of a solid ice cover subjected to rapidly varying water levels and discharge was investigated. The support from the bank limits the stress in the ice cover and consequently bank contact must be maintained to ensure ice cover stability. An analysis was required of the stability of ice hinges, a flexible connection between a solid ice cover and the riverbank. Phase II and phase III of the research involved a field study of the Peace River, investigating the evolution of ice hinges with water level variation, from initial ice cover cracking parallel to the banks, to a fully developed hinge. A test program of midwinter discharge variations was undertaken to gather specific data and measurements of ice hinge link length, ice thickness, hinge joint behavior, riverbank geometry, and response ...

1984-11-01

22

Sinus Surgery  

Medline Plus

... know if the drainage becomes very clear, like tap water. This may be the first indication that there ...

23

CT-guided percutaneous aspiration and drainage of postoperative abdominal fluid collections  

International Nuclear Information System (INIS)

The authors report the personal techniques and the results of CT-guided percutaneous drainage of postoperative abdominal fluid collections. CT-guided percutaneous drainage offers many advantages over surgery: it is less invasive, can be repeated and requires no anesthesia, there are not surgery-related risks and lower morbidity and mortality rates. Moreover, subsequent hospitalization is shorter and costs are consequently reduced. The authors conclude that CT-guided percutaneous drainage is the method of choice in the treatment of postoperative abdominal fluid collections.

1999-03-01

25

APOD: 2004 September 4 - Neutron Mars  

Science.gov (United States)

ice could be responsible for the formation of martian gullies. Tomorrow's picture: whirlpool ...

2011-10-07

26

2009 Community Sequencing Program: Life Under Ice  

ScienceCinema

...carbon dioxide in the atmosphere contributes to global warming anything that could ...

27

Late cenozoic evolution of Fortymile Wash: Major change in drainage pattern in the Yucca Mountain, Nevada region during late miocene volcanism  

International Nuclear Information System (INIS)

The site characterization of Yucca Mountain, NV as a potential high level nuclear waste repository includes study of the surficial deposits as a record of the paleoenvironmental history of the Yucca Mountain region. An important aspect of this history is an understanding of the evolution of paleogeography leading to establishment of the present drainage pattern. Establishment of drainage basin evolution is needed before geomorphic response to paleoclimate and tectonics can be assessed, because a major change in drainage basin geometry can predominantly affect the sedimentary record. Because alluvial aquifers are significant to regional hydrology, a major change in surface drainage resulting in buried alluvium could have hydrogeologic significance. In this paper, we report on geologic evidence for a major modification in surface drainage pattern in the Yucca Mountain region, ...

1994-05-22

28

Heat transfer augmentation for external ice-on-tube TES systems using porous copper mesh to increase volumetric ice production  

Energy Technology Data Exchange (ETDEWEB)

Substantial thermal performance improvement in ice-on-tube cold thermal energy storage systems (TES) is possible by making use of porous copper mesh as a Heat Conducting Enhancement Device (HCED). HCEDs are inexpensive heat transfer augmentation devices that can result in faster rate of ice growth and larger final steady state ice build volume by reducing the controlling thermal conduction resistance of the ice layer. This improves the competitiveness of external ice-on-tube systems as compared to other TES systems, such as dynamic ice harvesters and static internal melt systems. In this study the amount of ice growth enhancement is predicted theoretically, by performing simplified 1-D calculations, and is then validated in the laboratory through carefully controlled experiments. This study shows that ice volume increase ...

2006-09-15

29

Collisions with ice-volatile objects: Geological implications  

International Nuclear Information System (INIS)

The collision of the Earth with extra-terrestrial ice-volatile bodies is proposed as a mechanism to produce rapid changes in the geologic record. These bodies would be analogs of the ice satellites found for the Jovian planets and suspected for comets and certain low density bodies in the Asteroid belt. Five generic end-members are postulated: (1) water ice; (2) dry ice: carbon-carbon dioxide rich, (3) oceanic (chloride) ice; (4) sulfur-rich ice; (5) ammonia hydrate-rich ice; and (6) clathrate: methane-rich ice. Due to the volatile nature of these bodies, evidence for their impact with the Earth would be subtle and probably best reflected geochemically or in the fossil record. Actual boloids impacting the Earth may have a variable composition, generally some admixture with water ice. However for ...

1988-10-20

31

Land uplift and relative sea-level changes in the Loviisa area, southeastern Finland, during the last 8000 years  

Energy Technology Data Exchange (ETDEWEB)

Southeastern Finland belongs to the area covered by the Weichselian ice sheet, where the release of the ice load caused a rapid isostatic rebound during the postglacial time. While the mean overall apparent uplift is of the order of 2 mm/yr today, in the early Holocene time it was several times higher. A marked decrease in the rebound rate occurred around 8500 BP, however, since then the uplift rate has remained high until today, with a slightly decreasing trend towards the present time. According to current understanding there have neither been temporary increases nor decreases in the rate of uplift during the postglacial time. Even so, it is not known for sure whether there are regional irregularities on the rebound in Finland. Concurrently with land uplift, relative sea-level changes in the Baltic basin were also strongly affected by the global eustatic rise of sea-level. During the early Litorina Sea stage on the ...

1999-09-01

33

June 1966  

Science.gov (United States)

Ultimate Compressive Strength of Short Sheet-Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and. Stringer ...

34

Goals, Strategies, and Top Accomplishments, May 2010 (Fact Sheet)  

Science.gov (United States)

Fact sheet describes the goals, strategies, and top accomplishments of the Clean Cities program.

2010-05-01

35

A risk based approach to assess the incidence of ice loads on small concrete dams  

International Nuclear Information System (INIS)

Some considerations regarding ice load in risk-based dam safety analysis are presented for small concrete dams. The most significant physical mechanisms leading to ice thrust on dams (such as thermal expansion and water level fluctuations) are outlined. Published literature on dam ice loads to examine ice load magnitude-return period relationships, sliding and overstressing failure mechanisms and structural performance criteria to resist ice loads, are also reviewed. Related loading combinations for structural safety evaluations were determined regarding the issue of simultaneity of ice loads with other events such as earthquakes. Parametric analyses were conducted on a small gravity dam section, 3m high, and a taller dam, 17.9 m high, to demonstrate the ultimate ice load carrying capability as a function of dam geometry and shear and ...

36

The efficacy of interventional therapy for hilar cholangiocarcinoma: a comparison between unilateral and bilateral biliary duct drainage  

International Nuclear Information System (INIS)

Objective: To compare the therapeutic effect of unilateral biliary duct drainage with bilateral biliary duct drainage in the treatment of Bismuth-Corlette II-IV type hilar cholangiocarcinoma in order to provide rational and proper clinical options. Methods: Biliary duct drainage was performed in 80 patients with hilar cholangiocarcinoma. The patients were divided into unilateral drainage group (n = 52) and bilateral drainage group (n = 28). The clinical data and the therapeutic results of the two groups were retrospectively analyzed and compared. Results The two groups were quite comparable in the patient's age, sex, clinical type, drainage way, preoperative total and direct bilirubin level, white blood cell, total protein and albumin, etc. After the treatment, the mean reduction value of the total bilirubin and direct bilirubin was 82.73 #mu#mol/L and ...

2009-08-01

37

GSFC Earth-Sun Exploration Division - Sciences and Exploration ...  

Science.gov (United States)

retrieve detailed aerosol and cloud particle size distribution and shape ...... but on rain types, and hydrometeor characteristics. ..... of ice streams, decreasing sea ice cover in the Arctic, poleward movement of forest cover, and ...

38

THE EFFECT OF THE ICE-SEPARATION CURVE ON THE ...  

Science.gov (United States)

... However, the solution of the Stefan problem in this context becomes abruptly complicated, since within each zone, the differential equations ...

39

STUDY AND MODIFICATION OF CONVECTIVE STORMS  

Science.gov (United States)

... small water or ice particles by impaction ... flight recording; principally the hydrometeor charge unit ... capability of directing aircraft movements by radio ...

1963-06-30

40

An Evaluation of the Severity of the January 1998 Ice Storm in ...  

Science.gov (United States)

... storm. There was little damage to high-voltage transmission lines and communication towers in northern New England. ...

1998-04-01

41

20 - NASA - Archive  

Science.gov (United States)

Biochar is fantastic for enriching soil, and you can make it yourself. Screen capture from video of sea ice minimum for 2010. ...

42

Improvement of methane drainage in high gassy coal seam using waterjet technique  

Energy Technology Data Exchange (ETDEWEB)

Traditional methane drainage methods, including conventional ventilation and boreholes drilled in the coal seam, are widely used in modern coal mining operation in China. However, it is often noted that the gas drainage presents low efficiency in most coal mines due to low permeability of the coal seam, which not only affects the safety, but also the productivity of the coal mine. This paper describes the development and application of the waterjet cutting system, which is used to create artificial fractures and increase the permeability of coal seam for the improvement of methane drainage in underground coal mines in China. According to underground monitoring, a significant improvement of methane drainage efficiency of up to 3 to 6 times over the traditional methods has been achieved. (author)

2009-07-01

43

Research - Keyword Index  

Wastenet

...and biological processes acting on recruitment and post-recruitment EU-Agrinet - Project sheet: Biological performance testing methodology to evaluate the durability of plywood as a quality indicator ... Project sheet: Biological performance testing methodology to evaluate the durability of plywood as a quali EU-Agrinet - Project sheet: Genetic evaluation of European ...

44

Waste generation and pollution prevention progress fact sheet: West Valley Demonstration Project  

Energy Technology Data Exchange (ETDEWEB)

This Fact Sheet presents the mission of the West Valley Demonstration Project and information on the 1994 pollution prevention and recycling accomplishments.

1994-12-31

45

Waste generation and pollution prevention progress fact sheet: Savannah River Site  

Energy Technology Data Exchange (ETDEWEB)

This Fact Sheet provides the mission of the Savannah River Site and information on 1994 pollution prevention and recycling accomplishments.

1994-12-31

46

Influence of salt and elevated-temperature exposure on the maximum ...  

Science.gov (United States)

Ultimate Compressive Strength of Short Sheet - Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and Stringer ...

47

Closed Cycle Bleach Kraft Pulp Production; NICE3 Forest Products Project Fact Sheet  

Energy Technology Data Exchange (ETDEWEB)

Fact sheet written for the NICE3 Program on a new chlorine-free process for pulping and bleaching wastewater.

2000-10-30

48

A Hybrid Kinetic Model of Asymmetric Thin Current Sheets ...  

Science.gov (United States)

... Accession Number : ADA539720. Title : A Hybrid Kinetic Model of Asymmetric Thin Current Sheets with Sheared Flows in a Collisionless Plasma. ...

2010-12-27

49

The IceCube Collaboration:contributions to the 30 th International Cosmic Ray Conference (ICRC 2007),  

Energy Technology Data Exchange (ETDEWEB)

This paper bundles 40 contributions by the IceCube collaboration that were submitted to the 30th International Cosmic Ray Conference ICRC 2007. The articles cover studies on cosmic rays and atmospheric neutrinos, searches for non-localized, extraterrestrial {nu}{sub e}, {nu}{sub {mu}} and {nu}{sub {tau}} signals, scans for steady and intermittent neutrino point sources, searches for dark matter candidates, magnetic monopoles and other exotic particles, improvements in analysis techniques, as well as future detector extensions. The IceCube observatory will be finalized in 2011 to form a cubic-kilometer ice-Cherenkov detector at the location of the geographic South Pole. At the present state of construction, IceCube consists of 52 paired IceTop surface tanks and 22 IceCube strings with a total of 1426 Digital Optical Modules deployed at depths up to 2350 m. The ...

2007-11-02

50

Numerical modelling of surface hydrology and near-surface hydrogeology at Forsmark. Site descriptive modelling SDM. Site Forsmark  

Energy Technology Data Exchange (ETDEWEB)

SKB is currently performing site investigations at two potential sites for a final repository for spent nuclear fuel. This report presents results of water flow and solute transport modelling of the Forsmark site. The modelling reported in this document focused on the near-surface groundwater, i.e. groundwater in Quaternary deposits and shallow rock, and surface water systems, and was performed using the MIKE SHE tool. The most recent site data used in the modelling were delivered in the Forsmark 2.3 dataset, which had its 'data freeze' on March 31, 2007. The present modelling is performed in support of the final version of the Forsmark site description that is produced during the site investigation phase. In this work, the hydrological modelling system MIKE SHE has been used to describe near-surface groundwater flow and the contact between groundwater and surface water at the Forsmark site. The surface water system at Forsmark is described with the one-dimensional ...

2008-09-15

51

Regulation of agricultural drainage to San Joaquin River  

Science.gov (United States)

A technical committee reported on: (1) proposed water quality objectives for the San Joaquin River Basin; (2) proposed effluent limitations for agricultural drainage discharges in the basin to achieve these objectives; and (3) a proposal to regulate these discharges. The costs and economic impact of achieving various alternative water quality objectives were also evaluated. The information gathered by the technical committee will be used by the Regional Board along with other information in their review of the San Joaquin River Basin Water Quality Control Plan and their actions to regulate agricultural drainage in the San Joaquin Valley. The results of the Technical Committee's efforts as reported in Regulation of Agricultural Drainage to the San Joaquin River, August 1987. Based on the available information, the improvement in water quality resulting from implementation of the interim selenium objective and ...

1989-02-01

52

Mine drainage treatment; Kogyo haisui shori  

Energy Technology Data Exchange (ETDEWEB)

The generation of acidic mine drainage is based on the oxidation dissolution of sulfide minerals due to the contact of ores with the natural water and the air. Namely, the sulfuric acid promotes the dissolution of sulfide minerals and gangue minerals, and Fe{sup 2+} is further oxidized to turn into Fe{sup 3+}, which acts as an oxidizer for other sulfide minerals and promotes the dissolution of the same. This paper roughly describes a mine drainage treatment focusing on an Fe{sup 2+} neutralization method and an iron bacteria oxidation method. The iron bacteria oxidation method is a method of oxidizing Fe{sup 2+} into Fe{sup 3+} by using iron bacteria, and then removing Fe{sup 3+} with calcium carbonate. This method has been used for treating the drainage in the Sakuhara Mine and the former Matsuo Mine, with good results. The paper finally introduces, as power-saving low-cost mine drainage treatment ...

1996-05-25

53

Nuclear data sheets for A=203  

Energy Technology Data Exchange (ETDEWEB)

Experimental data pertaining to nuclei with A=203 are compiled and evaluated.

1985-10-01

54

Nuclear data sheets for A=203  

International Nuclear Information System (INIS)

Experimental data pertaining to nuclei with A=203 are compiled and evaluated.

55

Magnesium foam produced from bulk AZ31 magnesium alloy sheets  

Energy Technology Data Exchange (ETDEWEB)

Using commercial AZ31 magnesium alloy sheets, we produced a foamable preform sheet containing titanium hydride (TiH{sub 2}) powder through diffusion-bonding and hot-rolling of four cycles. Heating the preform sheets in Ar atmosphere, we obtained closed-cell magnesium alloy foams with various porosities. The foamed specimen at 883 K showed the maximum porosities of 77%. (orig.)

2005-07-01

58

Global Warming and California's Public Health  

Science.gov (United States)

This fact sheet summarizes the potential impact of climate change as it relates to public health in California....

59

Global Warming and California's Electricity Supply  

Science.gov (United States)

This fact sheet summarizes the potential impact of climate change as it relates to California's electricity supply. ...

63

The onset conditions of enhancement of ice accumulation associated with heat-conducting plates located perpendicularly to heat-transfer surfaces; Part 1: Analysis for still water  

Energy Technology Data Exchange (ETDEWEB)

An analytical study of the ice-formation process associated with heat-conducting plates located perpendicularly to isothermally heated and cooled surfaces with some clearance is presented. It is proposed that the onset conditions, which describe whether the ice-volume fraction in a steady state is greater than or less than that without heat-conducting plates, are defined by the dimensionless distances between the heated/cooled walls and the heat-conducting plates. It is shown that the onset conditions are dependent on the pitch and the thickness of the heat-conducting plates and are less dependent on the thermal conductivity of the plates.

1994-07-01

64

Thoracoscopy in Children: Is a Chest Tube Necessary?  

UK PubMed Central (United Kingdom)

PurposeHistorically, a chest tube or drain has been left following a thoracic operation to allow drainage of air or fluid in the postoperative period. However, in...Full Text Available

2009-04-01

65

The interventional treatment for biliary recurrent obstruction after palliative T tube drainage in patients with obstruction due to cholangiocarcinoma  

International Nuclear Information System (INIS)

Objective: To explore the interventional method to treat biliary recurrent jaundice after T tube drainage in patients with malignant obstructive jaundice due to cholangiocarcinoma. Methods: 7 biliary metallic stents were placed in 7 patients with recurrent jaundice after T-tube drainage in cholangiocarcinoma cases. Results: Stent placement was once successful in all 7 cases with successful rate of 100%. For all cases, TBIL, ALT, GTP and AKP values 7 days postoperatively were significantly lower than that of preoperation together with subsidence of jaundice satisfactorily for 100% after the treatment. Conclusions: Percutaneous placement of biliary metallic stents was effective economic, minimal invasive and safe for palliation of biliary recurrent jaundice after T tube drainage in cholangiocarcinoma-induced obstructive jaundice

2002-10-01

66

The capacity of natural wetlands to ameliorate water quality: a review of case studies  

Energy Technology Data Exchange (ETDEWEB)

Case studies of natural wetlands for treating mine drainage are described. Most of the sites are in northern Canada. The natural wetlands examined suggest that constructed wetlands are a viable option for the passive treatment of mine drainage. Natural wetlands retain many metals, and many species of plants are represented in them. Processes for metal removal include sorption onto organic matter, hydrolysis, and reduction. The results show that wetlands need not be based on cattails to be effective, and that passive mine drainage treatment is feasible in northern regions. Few examples are available of constructed wetlands for treating metal mine drainage. It is concluded that the limitations of constructed wetlands are found not in the wetlands, but in information about them. 37 refs., 1 fig., 2 tabs.

1997-12-31

67

Competitive bidding under asymmetrical information: behavior and performance in Gulf of Mexico drainage lease sales, 1959-1969  

Energy Technology Data Exchange (ETDEWEB)

In past Outer Continental Shelf oil and gas lease sales, winners of drainage tracts have tended to realize a higher economic return than winners of wildcat tracts. This paper finds empirical support for the hypothesis that adjacent lessees have an information advantage when bidding for drainage tracts under the cash bonus bidding system. This leads to superior economic returns, and thus explains the difference in returns between wildcat and drainage leases. The paper concludes that this difference and its cause do not pose a policy problem given empirical evidence that the government receives fair market value for the two lease categories combined.

1984-08-01

68

When loss is more (for transmission towers) | SmartPlanet  

Wastenet

... ice, hurricanes, and trees (less likely on high voltage transmission lines ) can bring down above ground power lines. Flooding, Leeching ground ...

69

Statistical description and estimation of ocean drift ice environments  

Energy Technology Data Exchange (ETDEWEB)

Part I of this thesis is on long-term iceberg collision-risk assessment methods for fixed offshore structures. Estimates for the long-term probability that an iceberg will hit a fixed offshore structure are based on estimates of the total volume of produced iceberg, a model for the size distribution of icebergs and a description of how iceberg trajectories ``fill`` the plane (the ocean`s surface). Part II of the thesis discusses methods for analysis of low resolution data in the sense that the size of the area covered by each pixel is not small compared to the dominating floes. Still, this type of data can provide estimates of the ice extent (and hence the ice edge) and ice concentration. The estimates of the ice edge (at least) seem to be physically significant in the sense that ``in some way`` they can reflect ice drift in an image time sequence. A priori this is far from obvious. ...

1991-04-01

70

Phylogenetic Characterization of Virulence and Resistance Phenotypes of Pseudomonas syringae  

UK PubMed Central (United Kingdom)

Individual strains of the plant pathogenic bacterium Pseudomonas syringae vary in their ability to produce toxins, nucleate ice, and resist antimicrobial compounds. These phenotypes...Full Text Available

2005-09-01

71

Parameter Estimation in Moving Boundary Problems  

Science.gov (United States)

... Finally, the one dimensional, one phase Stefan problem is well known as a model for the melting of ice (see, eg, [5]). There are many approaches to ...

1988-05-01

72

NASAPerformance Report - NASA Technical Reports Server  

Science.gov (United States)

test bed (ADTT) tools technology. Glenn. Research. Center: Aircraft icing training video for regional and cor- porate pilots. Numerical propulsion ...

73

Measurements of the concentration and composition of nuclei for cirrus formation  

UK PubMed Central (United Kingdom)

This article addresses the need for new data on indirect effects of natural and anthropogenic aerosol particles on atmospheric ice clouds. Simultaneous measurements of the concentration and composition...Full Text Available

2003-12-09

74

MICRONUTRIENTS/TRACE ELEMENTS - Global Change Master Directory (GCMD)  

Science.gov (United States)

Total concentrations of major and trace elements were determined in samples of the epilithic lichen Umbilicaria decussata from 24 ice-free areas in coastal ...

75

ENGLISH R. PD.-SNOW-ICE - The Gateway to Astronaut Photography of ...  

Science.gov (United States)

Jul 26, 2011 ... The Gateway to Astronaut Photography of Earth hosts the best and most complete online collection of astronaut photographs of the Earth.

76

Decline in Arctic sea ice thickness from submarine and ICESat ...  

Science.gov (United States)

estimates from 42 years of submarine records (19582000) described by ... area (DRA) of declassified submarine sonar measurements. (covering $38% of the ...

77

Debris/ice/TPS Assessment and Integrated Photographic Analysis of ...  

Science.gov (United States)

assessment.Both frustumswerein excellentcondition.No missingTPSor debonds/ unbondswere ...... 2) The average time for a 360 degree rotation was 29.9 seconds. ...

78

A comparison of benthic biodiversity in the North Sea, English ...  

Science.gov (United States)

A comparison of benthic biodiversity in the North Sea, English Channel, and Celtic Seas. ICES J. Mar. Sci./J. Cons. int. Explor. Mer 56: 228-246. ...

79

Proceedings of MEND 2000 symposium : research on innovative methods to control acid mine drainage; Comptes rendus du NEDEM 2000 : colloque sur la recherche de methodes innovatrices pour le controle du drainage minier acide  

Energy Technology Data Exchange (ETDEWEB)

The 24 papers presented at the conference on Neutralisation des eaux de drainage dans l'environnement minier (NEDEM) (Mine Environment Neutral Drainage (MEND)) 2000 symposium on research on innovative methods to control acid mine drainage, covered eight sessions with both technical and general interest papers. The technical papers covered the topics of acid mine drainage and remediation measures, such as flooding, soil cover with various materials, encapsulation, and others. Other topics discussed included the freeze-thaw cycle and its effect on the performance of soil covers. The environmental impacts of acid mine drainage were also described. Some case studies were included to further illustrate the environmental impacts of acid mine drainage and to demonstrate the effectiveness of remedial actions in specific situations. Most of the cases studied ...

2000-07-01

80

Pericardio-peritoneal drainage using a subcostal approach.  

Science.gov (United States)

A 56-year-old man admitted to our hospital for cardiac tamponade due to dilated cardiomyopathy did not respond to treatment by usual medical means or surgery. Pericardio-peritoneal drainage was conducted using a subcostal approach. Seven months later, the patient remains well and free of signs of pericardial tamponade. This method has proved to be safe and effective in patients with persistent massive pericardial effusion. PMID:10496067

1999-08-01

81

Evaluation of a computer program used to estimate water characteristic curve  

Science.gov (United States)

The soil water characteristic curve, h(theta), can be used to estimate a variety of parameters in unsaturated soils. One practical application of h(theta) is its use by DRAINMOD, a drainage model that has been widely used in shallow water table regions, to determine the water table depth¿drainage v...

82

Conference on climate and water. Volume 2  

Energy Technology Data Exchange (ETDEWEB)

This book contains the Proceedings of the Conference on Climate and Water under the following groupings: Impacts of climatic variability and change-resulting from the changes in hydrological variables; Aquatic environment; Terrestrial environment; Coastal zones and navigation; Urban and industrial water supply and drainage; Energy production; Intropogenic changes of climate and water management problems; Flood potential; Irrigation and land drainage.

1989-12-31

83

Conference on climate and water  

Energy Technology Data Exchange (ETDEWEB)

This book contains the Proceedings of the Conference on Climate and Water under the following groupings: Impacts of climatic variability and change-resulting from the changes in hydrological variables; Aquatic environment; Terrestrial environment; Coastal zones and navigation; Urban and industrial water supply and drainage; Energy production; Intropogenic changes of climate and water management problems; Flood potential; Irrigation and land drainage.

1989-01-01

84

Utilization of Fluorescent Microspheres and a Green Fluorescent Protein-Marked Strain for Assessment of Microbiological Contamination of Permafrost and Ground Ice Core Samples from the Canadian High Arctic  

UK PubMed Central (United Kingdom)

Fluorescent microspheres were applied in a novel fashion during subsurface drilling of permafrost and ground ice in the Canadian High Arctic to monitor the exogenous microbiological contamination of...Full Text Available

2005-02-01

85

Detection and Isolation of Ultrasmall Microorganisms from a 120,000-Year-Old Greenland Glacier Ice Core  

UK PubMed Central (United Kingdom)

The abundant microbial population in a 3,043-m-deep Greenland glacier ice core was dominated by ultrasmall cells (<0.1 μm3) that may represent intrinsically small organisms...Full Text Available

2005-12-01

86

Percutaneous drainage of abdominal abcess  

Energy Technology Data Exchange (ETDEWEB)

The mortality in undrained abdominal abscesses is high with a mortality rate ranging between 45 and 100%. The outcome in abdominal abscesses, however, has improved due to advances in image guided percutaneous interventional techniques. The main indications for the catheter drainage include treatment or palliation of sepsis associated with an infected fluid collection, and alleviation of the symptoms that may be caused by fluid collections by virtue of their size, like pancreatic pseudocele or lymphocele. The single liver abscesses may be drained with ultrasound guidance only, whereas the multiple abscesses usually require computed tomography (CT) guidance and placement of multiple catheters. The pancreatic abscesses are generally drained routinely and urgently. Non-infected pancreatic pseudocysts may be simply observed unless they are symptomatic or cause problems such as pain or obstruction of the biliary or the gastrointestinal tract. Percutaneous routes that ...

2002-09-01

87

In situ studies with Asian clams (Carbacula fluminea) detect acid mine drainage and nutrient inputs in low-order streams  

International Nuclear Information System (INIS)

This study evaluates the correlation between transplanted Asiatic clam and indigenous community responses to acid mine drainage and nutrient loading in first-to-third-order streams, by comparing the toxicological endpoints of clam survival and growth with benthic macro-invertebrate community indices as community responses to both acid mine drainage and nutrient loading. Clam survival was found to be positively correlated with water column pH and negatively correlated with conductivity and metal concentrations. There was also a positive correlation with the relative abundance of the macro-invertebrate Ephemeroptera, the most sensitive taxonomic group, to acid mine drainage in this watershed. No correlation was found between clam growth and acid mine drainage inputs, but there was evidence of positive correlation with nitrate concentrations and the relative abundance of collector-filterer functional ...

2001-03-01

88

A process model of natural attenuation in drainage from a historic mining district  

Energy Technology Data Exchange (ETDEWEB)

A process model was used to better understand the controls on the chemical evolution of drainage in a historic mining district. At the Pecos Mine Operable Unit, New Mexico, drainage near the waste rock pile is acidic (pH varies from 3.0--5.0) and carries high concentrations of Zn, Al, Cu and Pb. As drainage flows toward the Pecos River, pH increases to greater than 7 and heavy metal content decreases. A process model of natural attenuation in this drainage shows the main controls on pH are reaction with a local bedrock that contains limestone, and concurrent mixing with tributary streams. Models that account for both calcite dissolution and mixing reproduce the observed decrease in aqueous metal concentrations with increasing pH. Contaminant concentrations attenuate primarily via two distinct pathways: Al, Cu, Fe and Pb precipitate directly from solution, whereas Zn, Mg, Mn and SO{sub 4} concentrations ...

2000-06-05

89

Construction method of the artificial iced bobsleigh and luge track. Aiming at the Nagano Winter Olympic Games; Tekkin concrete sei bobsleigh luge track no kensetsu. Nagano Olympic toki kyogi taikai wo mezashite  

Energy Technology Data Exchange (ETDEWEB)

The reinforced concrete artificial iced course, constructed first in Japan as a bobsleigh and luge track for the Nagano Olympic Games, has a total extension of 1,700 m and an altitude difference of 113 m. It contains 15 curves and 2 up-grades and is divided into 43 blocks with spans ranging from 20 m to 80 m, all of which consist of lightwall RC members supported by pile foundations. The surface is cooled to -15 centigrade by the cooling pipes embedded in concrete and is iced by spraying water, and iced surface is shaved to make a course. Since the course scarcely has same profiles, the finished wall thickness is secured by fixing wire gauzes on the required positions without using shutterings. As there is not existed concrete satisfying all the required quality, two kinds of concrete were selected for filling in the arrangement of reinforcement and pipes and for surface finishing. Special notice was taken of the accuracy ...

1996-03-10

90

Waste Generation and Pollution Prevention Progress Fact Sheet: Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

This 2-page fact sheet gives statistics on routine waste generation and projected reduction by waste type, and 1994 pollution prevention and recycling accomplishments at ORNL.

1996-09-01

91

Nuclear Data Sheets for A = 88  

Energy Technology Data Exchange (ETDEWEB)

The 1976 version of Nuclear Data Sheets for A = 99 (76Bu07) has been revised. Detailed level and decay schemes, arguments for J..pi.. assignments, and experimental data are presented. copyright 1988 Academic Press, Inc.

1988-05-01

92

Nuclear Data Sheets for A = 88  

International Nuclear Information System (INIS)

The 1976 version of Nuclear Data Sheets for A = 99 (76Bu07) has been revised. Detailed level and decay schemes, arguments for J#pi# assignments, and experimental data are presented. copyright 1988 Academic Press, Inc.

93

Nuclear Data Sheets for A = 203  

International Nuclear Information System (INIS)

Evaluated nuclear structure and decay data for all nuclei within the A = 203 mass chain are presented. This work supersedes the earlier evaluation by S. Rab (1993Ra11), published in Nuclear Data Sheets 70, 173 (1993).

2005-05-01

96

Sheet1  

Science.gov (United States)

... 15, 14, Robert Constable, Cornell University, NY, Building Interactive Digital Libraries of Formal Algorithmic Knowledge, Navy. ...

97

Methods and instruments for nondestructive testing of the anisotropy of the magnetic properties of ferromagnetic sheet materials (review)  

Energy Technology Data Exchange (ETDEWEB)

This review of methods and designs of transducers for nondestructive determination of the magnitude and nature of the anisotropy of magnetic properties (permeability, induction, coercive force, energy loss due to magnetization reversal) in local portions of ferromagnetic sheet and, in some cases, in individual parts of products. The need to measure the anisotropy is considered for two angles: for the case when the anisotropy is due to the crystallographic texture and determines the main operating characteristics of widely used sheet such as electrical steel and automobile body sheet, and for crystallographically isotropic materials, in which the anisotropy of magnetic properties as a result of mechanical stresses is a measure for determining the internal stresses.

1995-04-01

99

Effect of cross rolling parameters on texture formation and parameters on texture formation and anisotropy of mechanical properties of (#alpha#+#beta#)-titanium alloy sheets  

International Nuclear Information System (INIS)

Formation of basis type texture at rolling of Ti + 6.0% Al + 1.5% V + 1.0% Mo system alloy with initial prismatic texture is investigated by means of X-ray techniques. Variations of mechanical features in titanium alloy sheets depending on temperature-deformation conditions of rolling are investigated. Main conditions for formation of the intensive basis textute in the investigated alloy sheets which provides for isotropic properties in sheet plane and for increased ductility are determined.

100

Percutaneous transhepatic biliary drainage for hilar cholangiocarcinoma  

International Nuclear Information System (INIS)

Objective: To evaluate the effect of PTBD in treating malignant biliary obstruction caused by hilar cholangiocarcinoma. Methods: We retrospectively analyzed the data of 103 patients(M:62,F:41)with malignant obstructive jaundice caused by hilar cholangiocarcinoma. After taking percutaneous transhepatic cholangiography, metallic stent or plastic external catheter or external-internal catheter for drainage was deployed and then followed up was undertaken with clinical and radiographic evaluation and laboratory. examination. Results: All patients went though PTBD successfully (100%). According to Bismuth classification, all 103 cases consisted of I type(N=30), II type (N=30), III type (N=26) and IV type (N=17). Thirty-nine cases were placed with 47 stents and 64 eases with drainage tubes. 4 cases installed two stems for bilateral drainage, 2 cases installed two stents because of long segmental strictures with stent in stent, 1 ...

2007-10-01

101

New approach to the design of LMFBR liners  

Energy Technology Data Exchange (ETDEWEB)

The reconstruction of steel lining of the FFTF reactor building is described. The cold part of the lining has a simple structure and represents a steel sheet of 6.35 mm thickness welded to I-shaped imbedded in concrete, the hot part is meant for resisting the hot sodium contacting with it. The reconstruction has been reduced to the substitution of usual lining, the sheets of which are fixed in such a way that dangerous strains in metal arising at evaporation are excluded by the new structure admitting sheet deformation.

1981-01-01

102

Influence of rolling conditions on the microstructure and mechanical properties of magnesium sheet AZ31  

Energy Technology Data Exchange (ETDEWEB)

Two aspects of the deformation behavior of magnesium sheets are the subject of this paper. First it will give a mechanical characterization of a commercial magnesium with a focus on the anisotropy and the possible microstructural causes of this behavior. The rolling process will be part of the second aspect. The aim is to show the influence of the parameters on the microstructure and texture and how this could affect the anisotropy in the rolled sheets. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

2003-12-01

103

Water management studies in PEM fuel cells, part III: Dynamic breakthrough and intermittent drainage characteristics from GDLs with and without MPLs  

British Library Electronic Table of Contents (United Kingdom)

The transport of liquid water and gaseous reactants through a gas diffusion layer (GDL) is one of the most important water management issues in a proton exchange membrane fuel cell (PEMFC). In this work, the liquid water breakthrough dynamics, characterized by the capillary pressure and water saturation, across GDLs with and without a microporous layer (MPL) are studied in an ex-situ setup which closely simulates a real fuel cell configuration and operating conditions. The results reveal that recurrent breakthroughs are observed for all of the GDL samples tested, indicating the presence of an intermittent water drainage mechanism in the GDL. This is accounted for by the breakdown and redevelopment of the continuous water paths during water drainage as demonstrated by Haines jumps. For GDL ...

2010-01-01

104

Application of remote sensing and geophysics to the detection and monitoring of acid mine drainage  

Energy Technology Data Exchange (ETDEWEB)

The results of a study on the application of remote sensing and geophysical methods for the detection and monitoring of acid mine drainage (AMD) are summarized, with emphasis on those that appear most suitable. The study consisted of a literature review, an information survey of users and suppliers, and discussions with various experts. Space-borne sensors, airborne sensors, airborne videography and digital frame cameras, spectroradiometers, radar, and photographic data are considered. Geophysical methods are effective for measurement of sulphides, areas of active chemical oxidation, acid mine drainage, and contaminated ground water movement. The popularity and effectiveness of various geophysical methods are rated for AMD applications. 25 refs., 1 fig., 3 tabs.

1995-06-01

105

Status of combined point source search with neutrino telescopes IceCube and AMANDA  

Energy Technology Data Exchange (ETDEWEB)

In this talk, we summarize recent results obtained from the combined neutrino telescopes IceCube and AMANDA. The combined approach, including data taken from both detectors simultaneously, is compared to other analyses that are using IceCube only data. The main benefit of the combined detector is its improved performance at low energies, meaning energies below 1 TeV (close to the energy threshold of the detector). The discussion is focused on the search for extra-terrestrial neutrinos from candidate sources in our Galaxy. Using appropriate cuts, the sensitivity can be optimized for soft spectra neutrino sources. With the resulting data sample, several studies are performed: an unbinned Galactic Plane Scan and a Cygnus region analysis: the Multi Point Source analysis. The current status of these analyses is presented.

2010-07-01

106

Direct detection of Salmonella without pre-enrichment in milk, ice-cream and fruit juice by PCR against hilA gene  

British Library Electronic Table of Contents (United Kingdom)

A novel PCR based assay was devised to specifically detect contamination of any Salmonella serovar in milk, fruit juice and ice-cream without pre-enrichment. This method utilizes primers against hilA gene which is conserved in all Salmonella serovars and absent from the close relatives of Salmonella. An optimized protocol, in terms time and money, is provided for the reduction of PCR contaminants from milk, ice-cream and juice through the use of routine laboratory chemicals. The simplicity, efficiency (time taken 3-4 h) and sensitivity (to about 5-10 CFU/ml) of this technique confers a unique advantage over other previously used time consuming detection techniques. This technique does not involve pre-enrichment of the samples or extensive sample processing, which was a pre-requisite in mos...

2012-01-01

107

1991 ice jamming along the Saint John River: a case study  

Energy Technology Data Exchange (ETDEWEB)

Field investigations of major and damaging ice jamming on the Saint John River at Dickey, Maine , and at Sainte-Anne de-Madawaska, New Brunswick, in 1991, were described. The investigations included measurement of water surface profiles and shear wall heights at both sites. The measurements were supplemented by information from local observers and data collection agencies. Using a simplified equilibrium analysis, ice jam thickness and water level at the Dickey site was found to be generally in agreement with observed values. At Sainte-Anne-de-Madawaska sufficient data was obtained to construct and calibrate the numerical model RIVJAM which determined the configuration of the jam in nonequilibrium reaches. Use of the model enabled the successful reproduction of a measured water profile along the jam and the prediction of the approximate thickness of the jam, which was generally less than the measured shear wall height. 14 refs., 11 figs.

1996-04-01

108

Three-dimensional particle simulation of plasma instabilities and collisionless reconnection in a current sheet  

Energy Technology Data Exchange (ETDEWEB)

Generation of anomalous resistivity and dynamical development of collisionless reconnection in the vicinity of a magnetically neutral sheet are investigated by means of a three-dimensional particle simulation. For no external driving source, two different types of plasma instabilities are excited in the current layer. The lower hybrid drift instability (LHDI) is observed to grow in the periphery of current layer in an early period, while a drift kink instability (DKI) is triggered at the neutral sheet in a late period as a result of the nonlinear deformation of the current sheet by the LHDI. A reconnection electric field grows at the neutral sheet in accordance with the excitation of the DKI. When an external driving field exists, the convective electric field penetrates into the current layer through the particle kinetic effect and collisionless reconnection is triggered by the convective electric ...

1999-06-01

109

Recycling of poly(methyl methacrylate) scrap in the styrene-methyl methacrylate copolymer cast sheet process  

British Library Electronic Table of Contents (United Kingdom)

Poly(methyl methacrylate), PMMA, scrap generated during the casting process for PMMA cast sheet is an industrial waste stream, which has a high impact on the PMMA production cost and environment. This paper presents an alternative way to reduce the processing cost of PMMA cast sheet and decrease industrial waste by using styrene (S) as a co-monomer with methyl methacrylate (MMA) monomer, in conjunction with recycling of PMMA scrap in the S-MMA copolymer cast sheet process. The influence of factors, such as the concentrations of S and PMMA scrap, on the preparation of S-MMA copolymer cast sheet mixed with PMMA scrap was investigated. The characterization of basic copolymer composition, the physical, and the mechanical properties of the final products were examined. The results show that it ...

2009-01-01

110

Isothermal sheet formability and microstructure study of rolling processed magnesium alloy AZ31  

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

2003-07-01

111

Farm Business Management. Volume I. Vocational Agriculture Education.  

Science.gov (United States)

This curriculum guide provides a basic core of instruction for the first year of a three-year adult program in farm business management. It contains 12 units of instruction. Each unit consists of seven basic components: performance objectives, teacher activities, information sheets (content essential for meeting the cognitive objectives), assignment sheets (application of knowledges that are prerequisites to skill development), supplements and transparency masters, tests, and test and assignment sheet answers. Depending on the specific objectives, supplements, transparency masters, assignment sheets, and job sheets may or may not be included. The 12 units cover orientation, recordkeeping, inventory and net worth statement, depreciation, enterprise accounting and supplemental records, enterprise budgets, cash-flow planning, farm credit, partial budgeting, marketing, income tax ...

1983-12-01

112

Measurement of spatial dose distribution with thermoluminescence sheet around high dose-rate intracavitary sup 60 Co sources  

Energy Technology Data Exchange (ETDEWEB)

A thermoluminescence (TL) sheet and its spatial readout system for in vivo measurement of spatial dose distribution around sources has been newly developed for intracavitary high dose-rate radiation therapy. The TL sheet (40 cm x 50 cm x 200 {mu}m), which is composed of teflon mixed with BaSO{sub 4} (Eu doped) powder, has a linear response with a very wide dynamic range from at least 0.002 cGy to 5000 cGy for {sup 60}Co sources. Phantom test of the TL sheet readout system demonstrated that absorbed dose with TL sheet and that with ionization chamber as standard dosimeter agreed well. For clinical application, TL sheet was attached on an applicator of intracavitary radiation therapy for rectal cancer. After irradiation with high dose-rate {sup 60}Co sources, the in vivo dose distribution on the surface of the rectum was determined. The TL sheet was suggested to ...

1991-06-01

113

Water and oxygen transfer in a waste rock pile constructed by mixing layers; Transfert de l'eau et de l'oxygene dans une halde de steriles construite par entremelement par couches  

Energy Technology Data Exchange (ETDEWEB)

Acid mine drainage represents one of the most important environmental problem facing the mining industry. If the tailings contain sulphur, acid mine drainage will be generated as soon as the tailings are exposed to oxygen. In this paper, the authors discussed a technique for the storage of acid mine drainage generating tailings that delays and even eliminates the occurrence. It was suggested that tailings should be piled by incorporating, at regular intervals, compacted waste rock. Thermal convection and diffusion will prevent oxygen from reaching the tailings, and limit water circulation. The modelling of transfer processes (heat, water, oxygen) in a well known tailings dump, the Doyon Mine, was performed, and the results compared to the modelling where compacted waste rock had been incorporated at regular intervals. The results indicated that by remaining saturated, the layers acted as capillary barriers preventing oxygen ...

2000-07-01

114

Technological and biological reclamation of overburden dumps in NCL  

Energy Technology Data Exchange (ETDEWEB)

Methods and materials employed by NCL to reclaim treatment of overburden dumps in opencast projects are described. These involve controlling slope stability and erosion (for example by covering with geosynthetic composites or jute/coir mat) and installing a drainage system before planting trees, shrubs and grass. 1 photo.

2000-05-01

115

Synthetic aperture radar image of agricultural fields with surface drainage network: simulation and spatial information retreival  

Science.gov (United States)

We develop a 3-D model to simulate the synthetic aperture radar (SAR) image formation process of an undulated vegetation canopy such as corn grown in fields with large periodic drainage reliefs. We explain how the simulated SAR image of undulated vegetation medium is obtained by the convolution of a 2-D slice of the 3-D simulated SAR system point spread function [(PSF), emulating the SAR beam modeled by a cosine modulated Gaussian], with the 2-D projection of the observed undulated vegetation canopy (modeled with scatterers randomly distributed in 3-D undulated space) followed by the extraction of each look envelope, the summation of looks, and sampling in azimuthal and range directions. Our model is useful to study the parameters involved in the formation and the analysis of SAR images of undulated vegetation medium. Validation of simulations made with actual SAR images shows that undulated corn crop canopies are well characterized by the mean contrast of the ...

2001-10-01

116

SIERRA GORDA - The Gateway to Astronaut Photography of Earth  

Science.gov (United States)

ISS022, E, 8269, CHILE, OPEN PIT MINING OPERATIONS E. OF SIERRA GORDA, ROADS, DRAINAGE, -22.9, -69.1, 20091209. ISS022, E, 8270, CHILE, OPEN PIT MINING ...

117

Remote environmental monitoring at No. 26 Colliery  

Energy Technology Data Exchange (ETDEWEB)

The author describes the layout of the environmental monitoring scheme at Devco's No. 26 Colliery in Canada, which includes wall face ventilation, fan performance, and methane drainage monitoring. He gives details of the sensors, outstations, and the surface control room.

1982-03-01

118

Regulation of hyaluronan secretion into rabbit synovial joints in vivo by protein kinase C  

UK PubMed Central (United Kingdom)

Hyaluronan (HA) is important for joint cavitation, lubrication, volume regulation and synovial fluid drainage but little is known about the regulation of joint HA synthesis/secretion in vivo....Full Text Available

2003-07-15

119

Prolonged lymphatic leak after retroperitoneal lymph node dissection: a case report  

UK PubMed Central (United Kingdom)

IntroductionPersistent lymphatic drainage following retroperitoneal lymph node dissection for testicular tumor is an uncommon complication.Case presentationWe...Full Text Available

120

Immunoglobulins in myasthenia gravis. Kinetic properties of the acetylcholine-receptor antibody studied during lymph drainage.  

UK PubMed Central (United Kingdom)

A specific immunoglobulin, the receptor antibody, can be found in most patients with myasthenia gravis. In order to study the kinetic properties of this antibody, serial determinations of receptor antibody,...Full Text Available

1978-10-01

121

Bedload measurements, East Fork River, Wyoming  

UK PubMed Central (United Kingdom)

A bedload trap in the riverbed provided direct quantitative measurement of debris-transport rate in the East Fork River, Wyoming, a basin of 466 km2 drainage area. Traction load moves only...Full Text Available

1976-04-01

122

Waiting For Lift-off Cake - NASA  

Science.gov (United States)

1 yellow cake mix 1 container star sprinkles 1 box of regular ice cream cones 2 vanilla frosting containers 1 box Teddy Grahams Green food coloring ...

123

User Manual for the NASA Glenn Ice Accretion Code ... - GLTRS - NASA  

Science.gov (United States)

eling of the Stefan Problem, AIAA J., vol. 22, Nov. 1984, pp. 1685-1690. Schlichting, H., Boundary-Layer Theory. F. J. Cerra, ED. ...

124

Temperature profiles and bathymetry of some high mountain lakes  

UK PubMed Central (United Kingdom)

The ice cover in high mountain lakes breaks up and disappears in about an hour, in part because it has been divided into fragile vertical spindles, which are individual crystals. Contributing to this...Full Text Available

2000-06-06

125

Study on separation of CO2 gas by TSS (thermal swing sublimation) method. Part 2; TSS ho (Thermal Swing Sublimation: ondo swing shokaho) ni yoru tansan gas bunri no kenkyu. 2  

Energy Technology Data Exchange (ETDEWEB)

TSS (thermal swing sublimation) method was studied which uses vaporization heat and sensible heat of LNG for solidification and separation of CO2 gas in waste gases of LNG-fired combined cycle power generation system. In experiment, the mixed gas composed of CO2, H2O and N2 was used for simulating waste gas of LNG-fired combined cycle power generation systems, and the growth behavior of ice and dry ice was studied for developing dry ice making technology under low-temperature condition. As the experimental result, the following were clarified: various crystal structures depending on cooling temperature, the effect of gas flow rate on peeling of surface precipitated solids, and solidification characteristics of H2O/CO2 mixed gas. The growth rate of precipitated solid film thickness decreased with an increase in gas flow rate, while increased with CO2 concentration. The shape of a dry ice sublimator ...

1997-03-21

126

RF tumor ablation with internally cooled electrodes and saline infusion: what is the optimal location of the saline infusion?  

UK PubMed Central (United Kingdom)

BackgroundRadiofrequency ablation (RFA) of tumors by means of internally cooled electrodes (ICE) combined with interstitial infusion of saline may improve clinical results. To date,...Full Text Available

127

Pseudocraters as indicators of ground ice on Mars  

International Nuclear Information System (INIS)

Positive identification of Martian pseudocraters would be a strong indication of past occurrence of ice at or near the surface of Mars. The basis for suggesting that small cones on Mars are pseudocraters includes: (1) small size, (2) abundant but patchy distribution on what appear to be volcanic plains, (3) presence of other features suggestive of surface or subsurface ice, (4) morphological similarities to Icelandic pseudocraters, and (5) the similarity in distribution of crater/cone diameter ratios to Icelandic pseudocraters. This last morphometric parameter may be the most important, since other possible small terrestrial volcanic analogs have very different crater/cone diameter ratio distributions. In a survey of the available high resolution Viking Orbiter imagery, abundant fields of possible pseudocraters were found. However, only a small fraction of the plains forming units imaged at high resolution were found to contain the small cones. ...

1987-05-01

128

Propagation Effects Handbook for Satellite Systems - DESCANSO - NASA  

Science.gov (United States)

time as well, due to the complex patterns of air movement taking place within cumulus clouds. ...... cumulative distribution of XPD, for rain and ice-particle induced ...... CCIR (1986f), Attenuation by Hydrometeors, In Particular ...

129

Intracardiac Echocardiography: A New Guiding Tool for Transcatheter Aortic Valve Replacement  

British Library Electronic Table of Contents (United Kingdom)

BackgroundEchocardiography has been debated as an adjunct for transcatheter aortic valve replacement (TAVR). The aim of this prospective study was to comparatively evaluate intraprocedural guidance using intracardiac echocardiography (ICE) and transesophageal echocardiography (TEE). MethodsFifty high-risk patients with severe aortic stenosis scheduled for TAVR were randomized to either guidance using ICE (group 1; n = 25) or monitoring using TEE (group 2; n = 25). ResultsIn contrast to TEE, ICE allowed continuous monitoring. The need for probe repositioning during the procedure was much lower in group 1 (0.1 +- 0.3 vs 5.7 +- 0.7 maneuvers, P P = .003). Both coronary ostia were more frequently visualized in group 1 (18 vs 2 cases, P n = 25, r2 = 0.90, P n = 11, P = .012), but ICE did not (m...

2011-01-01

130

Implications of abrupt climate change.  

UK PubMed Central (United Kingdom)

Records of past climates contained in ice cores, ocean sediments, and other archives show that large, abrupt, widespread climate changes have occurred repeatedly in the past. These changes were especially...Full Text Available

2004-01-01

131

Ice engineering advances : their impact on development concepts  

Energy Technology Data Exchange (ETDEWEB)

The Hebron offshore drilling project in Atlantic Canada was discontinued in 2002 due to economic challenges. Chevron-Texaco has conducted small-scale studies to find ways to improve the project's viability. One of the main challenges facing this offshore drilling project is the issue of iceberg scour and its effect on seafloor equipment. This paper demonstrates how advances in ice engineering have resulted in new and cost-effective development concepts for: central gravity base structures; wellhead gravity base structures; floating production, storage and offloading (FPSO) subsea facilities; and, long subsea tieback and trench optimization. New studies have provided a better understanding of ice contact pressures, drift velocities, iceberg management and interaction processes. New designs for gravity base structures can reduce wave loads. The selection of a new development concept is determined by economic viability, capital cost, ...

2004-07-01

132

Frequently Asked ... - Precipitation Measurement Missions - NASA  

Science.gov (United States)

... say for sure if the signal is coming from hail, lots of graupel, or some other hydrometeor . ... Precipitation forms when cloud droplets or ice particles in clouds grow and .... A landslide is the movement of rock, debris, or earth down a slope. ...

133

Characterization of MJO ... - Microwave Limb Sounder (MLS) - NASA  

Science.gov (United States)

Feb 15, 2008 ... hydrological properties (e.g., hydrometeor budgets, cloud ice/water, transports ... cloud fraction, mass and particle size. In combination, these .... anomaly in the LS is not simply due isentropic movement of water vapor relative ...

134

Characterization of Airborne Microbial Communities at a High-Elevation Site and Their Potential To Act as Atmospheric Ice Nuclei?  

UK PubMed Central (United Kingdom)

Bacteria and fungi are ubiquitous in the atmosphere. The diversity and abundance of airborne microbes may be strongly influenced by atmospheric conditions or even influence atmospheric conditions themselves...Full Text Available

2009-08-01

135

*1-Front Piece - NASA Aqua  

Science.gov (United States)

properties such as effective particle size, thermody- namic phase (water, ice), cloud-top properties ...... Green, R.O., and J.E. Conel, 1995: Movement of ..... vertical hydrometeor profiles from passive micro- wave sensors. IEEE Trans. ...

136

ESR studies on reactivity of HO{sub 2} radicals in polycrystalline ice: non-monotonic changes of disproportionation rate in the temperature range 100-200 K  

Energy Technology Data Exchange (ETDEWEB)

The kinetics of HO{sub 2} radicals in UV-irradiated frozen dilute solutions of H{sub 2}O{sub 2} were followed by the ESR technique. Radical disproportionations at the irradiation temperature were found to be adequately described in terms of dispersive kinetics by a second-order equal-concentration kinetic equation with rate parameters changing non-monotonically in the temperature range 100-200 K. These changes are thought to occur due to well separated structural relaxation regions of polycrystalline ice in the above temperature range. (author).

1994-11-01

137

Self-dual strings in six dimensions: Anomalies, the ADE-classification, and the world-sheet WZW-model  

CERN Document Server

We consider the (2, 0) supersymmetric theory of tensor multiplets and self-dual strings in six space-time dimensions. Space-time diffeomorphisms that leave the string world-sheet invariant appear as gauge transformations on the normal bundle of the world-sheet. The naive invariance of the model under such transformations is however explicitly broken by anomalies: The electromagnetic coupling of the string to the two-form gauge field of the tensor multiplet suffers from a classical anomaly, and there is also a one-loop quantum anomaly from the chiral fermions on the string world-sheet. Both of these contributions are proportional to the Euler class of the normal bundle of the string world-sheet, and consistency of the model requires that they cancel. This imposes strong constraints on possible models, which are found to obey an ADE-classification. We then consider the decoupled ...

2004-01-01

138

Controllable synthesis of graphene sheets with different numbers of layers and effect of the number of graphene layers on the specific capacity of anode material in lithium-ion batteries  

International Nuclear Information System (INIS)

High quality graphene sheets are synthesized through efficient oxidation process followed by rapid thermal expansion and reduction by H2. The number of graphene layers is controlled by tuning the oxidation degree of GOs. The higher the oxidation degree of GOs is getting, the fewer the numbers of graphene layers can be obtained. The material is characterized by elemental analysis, thermo-gravimetric analysis, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and Fourier transform infrared spectroscopies. The obtained graphene sheets with single, triple and quintuplicate layers as anode materials exhibit a high reversible capacity of 1175, 1007, and 842 mA h g-1, respectively, which show that the graphene sheets with fewer layers have higher reversible capacity. -- Graphical abstract: The typical TEM images of the graphene sheets derived from GO3(a), GO2(b) and ...

2011-05-01

139

Toward the production of 50 000 tonnes of low-carbon steel sheet for the LHC superconducting dipole and quadrupole magnets  

CERN Document Server

A total of 50 000 tonnes of low-carbon steel sheet has been ordered for the LHC main magnets. After three years of production, about 10 000 tonnes of steel sheet have been produced by Cockerill-Sambre Groupe Usinor. This paper gives a summary of the manufacturing process and improvements implemented as well as an overview of the difficulties encountered during this production. Preliminary statistics obtained for the mechanical and magnetic steel properties are presented. (6 refs).

2002-01-01

140

Numerical calculation of the Casimir forces between a gold sphere and a nanocomposite sheet  

International Nuclear Information System (INIS)

The repulsive Casimir force is expected as a force which enables to levitate small objects such as machine parts used in Micro Electro Mechanical Systems (MEMS), and superlubricity in MEMS may be realized by this levitation. We study the Casimir force between a gold sphere and a nanocomposite sheet containing many nickel nanoparticles. In particular, we focus on the dependence of the Casimir force on the separation between the gold sphere and the surface of the nanocomposite sheet. The Casimir force changes from the attractive force to the repulsive force as the separation increases. The strength of the repulsive force is, however, too small to levitate MEMS parts.

2010-11-01

141

Fireplaces and Fireplace Fuels.  

Science.gov (United States)

This instructional unit is one of 10 developed by students on various energy-related areas that deals specifically with fireplaces and fuels. Its objective is for the student to be able to discuss the structural design, operation, and efficiency of fireplaces and characteristics of different fireplace fuels. Some topics covered are fuels, elements of the fire triangle, factors relating to high efficiency of masonry fireplaces, uses of grates and chimney, heat recovery, and prefabricated and free standing fireplaces. Materials in each unit may include some or all of the following: terminal and specific objectives, list of references, information sheet with terms and definitions, informative materials, transparency masters, assignment sheet(s), and unit test with answers. (YLB)

1981-06-01

142

Cross-stacked carbon nanotube sheets uniformly loaded with SnO{sub 2} nanoparticles: a novel binder-free and high-capacity anode material for lithium-ion batteries  

Energy Technology Data Exchange (ETDEWEB)

SnO{sub 2}-carbon nanotube (CNT) composite sheets are synthesized using poly(vinylpyrrolidone) to uniformly load a monolayer of SnO{sub 2} nanoparticles onto the surfaces of CNTs and CNT bundles within cross-stacked CNT sheets. When they are used as high-capacity (over 850 mA h g{sup -1}) and binder-free anodes in rechargeable lithium-ion batteries, they exhibit good cycle performance. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

2009-06-12

144

Superplastic forming behaviors and microstructure characters of magnesium alloy sheet AZ31B  

International Nuclear Information System (INIS)

An experimental study on superplastic forming behaviors and microstructure characters of commercial magnesium alloy sheet AZ31B is presented in this paper. The main experimental results show that the commercial magnesium alloy AZ31B sheet has superplastic capability. For the received sheet without any pre-processing, the maximum elongation is 295%. The dynamic recrystallization and grain refinement can be found, In the case of temperature =# 350 deg. C. The superplastic behaviors can be improved by controlling the dynamic recrystallization and grain refinement. Some experimental results of free superplastic bulging are presented in this paper. The results show that influence of temperature on forming capability is much less than the influences of temperature on elongation. In addition, the maximum principle strain.

2004-06-10

145

Operation Greenhouse: Communications  

Science.gov (United States)

... 295 VIII Classification Criteria 305 IX List of Applicable JANAP's 307 X Sample Sheets, Eniwetok Consolidated Telephone Directory 309 ...

2011-05-13

146

Nuclear data sheets for A=242  

International Nuclear Information System (INIS)

The available nuclear structure information for all nuclei with mass number A=242 is presented. Various decay and reaction data are evaluated. Adopted data, levels, spin and parity assignments are given.

147

Nuclear data sheets for A = 101  

Energy Technology Data Exchange (ETDEWEB)

Detailed level and decay schemes are presented for the nuclei of the A = 101 mass chain. The level properties obtained from decay and reaction experiments are shown in the drawings. Experimental methods, references, and comments are given in the text.

1985-08-01

148

Nuclear data sheets for A = 101  

International Nuclear Information System (INIS)

Detailed level and decay schemes are presented for the nuclei of the A = 101 mass chain. The level properties obtained from decay and reaction experiments are shown in the drawings. Experimental methods, references, and comments are given in the text.

149

Magnetohydrodynamic structure of a plasmoid in fast ... - NASA  

Science.gov (United States)

We set a symmetric boundary at x=200 and a conducting wall at z=150. The domain of 0200. 0150 is resolved by 60004500 grid cells. Harris sheet ...

150

Low cost fabrication of sheet structure using a new beta titanium alloy, Ti-15V-3Cr-3Al-3Sn  

Science.gov (United States)

Development efforts have been undertaken to improve the processing and structural efficiencies of

1982-01-01

151

Laser-assisted asymmetric incremental sheet forming of titanium sheet metal parts  

British Library Electronic Table of Contents (United Kingdom)

Asymmetric Incremental Sheet Forming (AISF) is a relatively new manufacturing process. In AISF, a CNC driven forming tool imposes a localized plastic deformation as it moves along the contour of the desired part. Thus, the final shape is obtained by a sequence of localized plastic deformations. AISF is suitable for small series production of sheet metal parts as needed in aeronautical and medical applications. Two main process limits restrict the range of application of AISF in these fields. These are the low geometrical accuracy of parts made from titanium alloys or high strength steels and, for titanium alloys, the limited formability at room temperature. In this paper a new concept for laser-assisted AISF is introduced including the required components. Furthermore, the CAX tools used f...

2011-01-01

152

Improving the sheared edge in the blanking of commercial AZ31 sheet through texture modification  

British Library Electronic Table of Contents (United Kingdom)

Commercial rolled magnesium sheets of alloys AZ31 (Mg-3 mass%Al-1 mass%Zn) and ZE10 (Mg-1 mass% Zn-<1 mass% Rare Earths) in O-temper condition were used for blanking experiments near room temperature. A serrated fracture surface can be observed in case of AZ31 but not in case of ZE10. During the shearing process of the AZ31 sheet, many micro cracks parallel to the sheet plane are generated in the shearing zone. These micro cracks lead to the formation of loose particles during the shearing operation, which interfere with further processing of the part and incur additional costs by increasing the scrap rate. It is found that the strong basal texture of this alloy is an important reason for the generation of such serrated cracks. In this paper a new method of selective texture modification i...

2011-01-01

154

Bulk CS Overpack Salvage Drums United Nations (UN) ...  

Science.gov (United States)

... SHEET. UNLESS OTHERWISE SPECIFIED, MATERIALS WILL BE MINIMUM SIZE lAW MIL-STD-2073-1. 18. TOLERANCES ...

1997-08-01

155

The Stefan Problem Revisited: A Continuum Model of Frost Heave  

Science.gov (United States)

The classical Stefan problem describes the motion of a solidification front through a uniform half-space in response to a step change in temperature on its boundary. The predictions of such a model can be applied quite accurately to the freezing of water in a porous medium so long as the pore geometry remains unaltered by the passing solidification front. It is observed, however, that in fine-grained porous media, ice has a tendency to form in segregated horizontal bands, known as ice lenses, that disrupt the regular pattern of heat flow through their enhanced consumption of latent heat. This process, known as frost heave, causes significant ground deformation in regions subject to prolonged freezing, and is one of the most important weathering processes in polar and alpine regions. Recent improvements to our understanding of the mechanics of ice lens nucleation and growth are applied here to predict the conditions and ...

2005-12-01

156

Metal leaching and acid mine drainage in British Columbia; La lixiviation des metaux et le drainage acide en Colombie-Britannique  

Energy Technology Data Exchange (ETDEWEB)

This poster presentation dealt with a brief overview of the practices in effect in British Columbia related to metal leaching and acid mine drainage. The metals mined in the province include coal, gold, silver, copper, molybdenum, lead, and zinc. Some mines operate under the surface, while others are strip mines, etc. under a variety of climactic conditions and a host of different mining companies, such as Cominco, Placer Dome and Noranda. The primary objective is the prevention of negative environmental impacts on land and in the water. Salmon and other fish need to be protected. A secondary objective is the minimization of impacts on the biota, which requires a detailed study of ecological risks. The solution often lies in soil covering. To illustrate, the author described the situation at Huckleberry Mines Ltd. and the remedial action that was implemented, and discussed the results on the beavers. In conclusion, the author discussed the strategies implemented by ...

2000-07-01

157

Executive summary: Winter and spring water quality survey of acid mine drainage neutralization plants. Draft report  

Science.gov (United States)

On November 2, 1974, Skelly and Loy submitted recommendations to the United States Environmental Protection Agency concerning establishment of effluent limitations for the Coal Mining Point Source Category, culminating an exhaustive study of water treatment technology within the coal industry. Members of the National Coal Association alleged that the efficiency of acid mine drainage treatment plants and settling basins is seriously reduced during winter and spring seasons. The original study was conducted during the summer months, and review of historical seasonal effluent data indicated there may be validity to this claim. To validate and confirm the conclusions and proposed effluent limitations established in part from this historical data, a further sampling program was conducted during the winter and spring of 1975. This report presents the findings of that sampling program, and correlates previously collected sample data into a comprehensive assessment of the ...

1975-06-24

158

Behaviour of the de-inked tailings soil cover at the Clinton mining site; Comportement de la couverture de residus de desencrage au site minier Clinton  

Energy Technology Data Exchange (ETDEWEB)

The production of de-inked tailings in Quebec has significantly increased during the last decade. From less than 100,000 wet tons in 1990, the production of de-inked tailings reached 500,000 wet tons in 1995, and 510,000 wet tons in 1999. The geotechnical, hydraulic, and physico-chemical properties of de-inked tailings are favorable for its use as soil cover for the prevention of acid mine drainage at mining sites. In this presentation, the authors discussed the three-year monitoring of the behaviour of a membrane covering an old mining site with the potential to produce acid mine drainage. The site is located at the Clinton Mine, near Woburn, Quebec. The mine shaft was filled with the tailings and waste rock scattered around the site and covered with a protective membrane which included de-inked tailings. The profile of the membrane was discussed, as well as construction details. The results confirmed the good performance of the soil cover in ...

2000-07-01

159

Wind tunnel test on a straight wing vertical-axis wind turbine with attachment on blade surface  

Energy Technology Data Exchange (ETDEWEB)

There is a renewed interest in straight wing vertical axis wind turbines (SW-VAWT) which are usually installed on the roofs of high buildings in cities, urban areas and high mountain areas for independent electric power supply. SW-VAWTs have the advantages of simple design and low cost, as well as wind direction independence compared to the horizontal system. However, when SW-VAWTs are installed in cold regions, ice, snow and other attachments can affect its performance. In this study, clay was attached to the leading edge of the blade surface to determine how the performance of SW-VAWTs are affected by the mechanism of icing. Wind tunnel tests were used to study the rotational performance and power performance of the turbine blades. Icing prevention was also investigated. The attachment of clay on the leading edge of blade surface made the rotational performance of the SW-VAWT worse. The attachment of clay on the leading ...

2008-07-01

160

Nuclear data sheets for A = 177  

International Nuclear Information System (INIS)

Evaluated nuclear structure and decay data for all nuclei within the A=177 mass chain are presented. Significant new information is included since the previous evaluation of this mass chain. The present work supersedes the earlier one by E. Browne (1993Br06), published in Nuclear Data Sheets 68, 747 (1993).

2003-04-01

161

Nuclear Data Sheets for A = 216  

International Nuclear Information System (INIS)

Evaluated spectroscopic data for all nuclei with mass number A = 216 are presented together with the relevant level schemes from radioactive decay and nuclear reaction studies. The experimental data are evaluated, inconsistencies and discrepancies are noted, and adopted values for level and #gamma#-ray energies, #gamma# intensities, as well as for other nuclear properties are given. The present evaluation supersedes the earlier one on A = 216 by A. Artna-Cohen (1997Ar04), published in Nuclear Data Sheets 80, 157 (1997).

2007-05-01

162

Fuel Cell Power Model Elucidates Life-Cycle Costs for Fuel Cell-Based Combined Heat, Hydrogen, and Power (CHHP) Production Systems (Fact Sheet)  

Energy Technology Data Exchange (ETDEWEB)

This fact sheet describes NREL's accomplishments in accurately modeling costs for fuel cell-based combined heat, hydrogen, and power systems. Work was performed by NREL's Hydrogen Technologies and Systems Center.

2010-11-01

163

Fabrication of magnesium alloy (AZ31) sheet by extrusion  

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the extrusion characteristics of magnesium alloy (AZ31), a computer simulation was attempted. Tensile properties of as-cast billet with different strain rates were incorporated into the simulation. The results showed a great change in distribution of stress and strain at near die region by the ram travel. It was found that the average grain size at longitudinal edge of the extruded sheet was smaller than that at center region, which might be attributed to recrystallization caused by severe plastic deformation. (orig.)

2004-07-01

164

Two stents insertion via single tract for treatment of hepatic hilar cholangiocarcinoma  

International Nuclear Information System (INIS)

Objective: To evaluate the feasibility and clinical application of two stents insertion via single tract for treatment of hepatic hilar cholangiocarcinoma. Methods: Eighteen patients with hepatic hilar cholangiocarcinoma who had left and right bile duct obstruction were treated with stents insertion via right bile duct puncturing routeway. These two stents were implanted between right and left bile duct, and between right bile duct and common bile duct. Results: Eighteen patients obtained successful two stents placement by right bile duct puncturing tract and succeeded with internal drainage for all biliary tree jaundice subsided distinctly. Conclusions: The technique of two stents insertion via single tract could predigest interventional drainage procedure of high bile duct obstruction, reduce operation trauma, shorten handling time and possess promising application value

2003-12-01

165

Symptomatic hepatic cyst in a child: treatment with single-shot injection of tetracycline hydrochloride  

Energy Technology Data Exchange (ETDEWEB)

The prevalence of hepatic cysts is 0.1% to 0.5% based on autopsy studies, and 2.5% based on US examinations. Percutaneous therapies are a new alternative to surgery. They include simple percutaneous aspiration, catheter drainage alone, and catheter drainage with sclerotherapy. We present an 11-year-old boy admitted to hospital because of abdominal pain. A diagnosis of simple hepatic cyst was made, which was treated with aspiration and tetracycline hydrochloride solution (5%) injection into the cystic cavity. Complete regression was seen on US and MRI examination at 3 months, with total collapse and deflation of the cyst. The cyst regressed totally, leaving a hyperechoic linear scar on US examination at 1 year. On the basis of the clinical and imaging results obtained, percutaneous sclerotherapy of hepatic cysts can be recommended as the treatment of choice and as a valid alternative to laparoscopy in children. (orig.)

2009-10-15

166

MEND manual; Le manuel NEDEM  

Energy Technology Data Exchange (ETDEWEB)

This poster presentation details the procedure that was followed for the development of the Mine Environment Neutral Drainage (MEND) manual. This manual was developed to provide a detailed summary of the important results obtained through studies sponsored by the MEND program and other studies conducted on topics related to acid mine drainage. The manual was divided into volumes dealing with topics such as summary, sampling and analysis, predictions, prevention and control, treatment, and monitoring. Details concerning the format, research conducted under the auspices of MEND, utilization and limitations, methodology, variations, costs, and references were also discussed. The author stated that the manual is to be used as a guide. The proposed English publication dates for the volumes were indicated, and they ranged from the fall of 2000 for volumes 3, 5, and 6, to the CD-ROM publication in March 2001. The French publication is expected to be ...

2000-07-01

167

Spin dynamics in Ho{sub 2}Ru{sub 2}O{sub 7}  

Energy Technology Data Exchange (ETDEWEB)

The spin relaxation processes within the pyrochlore Ho{sub 2}Ru{sub 2}O{sub 7} have been investigated by neutron scattering and bulk property techniques. A single-ion process, that is thermally activated, dominates the spin-spin relaxation spectrum above 2 K. Assuming Arrhenius behaviour, we found an activation energy {delta} = (329 {+-} 6) K and characteristic relaxation time {tau}{sub 0} (5.2 {+-} 0.3) x 10{sup -12} s in the paramagnetic state, akin to those found in the spin ice, Ho{sub 2}Ti{sub 2}O{sub 7}. Atlow temperature (T<95 K) the activation energy lowers and below 20 K the entropy and ac susceptibility are similar to that observed in other spin ice compounds within a 10 kOe field.

2005-11-09

168

Spin dynamics in Ho_2Ru_2O_7  

International Nuclear Information System (INIS)

The spin relaxation processes within the pyrochlore Ho_2Ru_2O_7 have been investigated by neutron scattering and bulk property techniques. A single-ion process, that is thermally activated, dominates the spin-spin relaxation spectrum above 2 K. Assuming Arrhenius behaviour, we found an activation energy #DELTA# = (329 #+-# 6) K and characteristic relaxation time #tau#_0 (5.2 #+-# 0.3) x 10"-"1"2 s in the paramagnetic state, akin to those found in the spin ice, Ho_2Ti_2O_7. Atlow temperature (T<95 K) the activation energy lowers and below 20 K the entropy and ac susceptibility are similar to that observed in other spin ice compounds within a 10 kOe field.

2005-11-09

169

Ocean teleconnections between Antarctica and the Equatorial Pacific and Atlantic.  

Environmental Research Database

Objectives(i) Investigate the correlation between Antarctic sea-ice and equatorial sea-surface temperature anomalies in a realistically forced ocean model simulation of the last 50 years. (ii) Determine whether and how the enormous seasonal change in distribution of sea-ice modifies the seasonal cycle at the Equator. (iii) Determine the detailed pathways of wave propagation both in a historically-forced simulation and in response to realistic perturbations. (iv) Quantify the amplitude of the response i [continued...]DescriptionIt is well known that the equatorial ocean-atmosphere system plays a key role in global climate events such as the El Nino-Southern Oscillation (ENSO) phenomenon. There is now compelling evidence that changes in the Antarctic can strongly and quickly affect the equatorial ocean and the ENSO cycle. Observations demonstrate statistically significant correlations (teleconnections) between the Antarctic and the Equator with ...

2009-01-31

170

Ground temperature histories in eastern and central Canada from geothermal measurements - evidence of climatic change  

Energy Technology Data Exchange (ETDEWEB)

Inverse and direct methods have been used to analyze a large number of borehole temperature logs in order to infer past climatic changes. Results indicate a warming of 1-2[degree]C in eastern and central Canada during the past 150 years. A period of cooling between 500 and 200 years before present, corresponding to the time of the Little Ice Age, has also been identified in the same areas. A regional ground temperature history is estimated for eastern and central Canada from the simultaneous inversion of several temperature logs. The inferred temperature changes appear correlated with the concentration of atmospheric carbon dioxide as reported from a Greenland ice core, and agree with existing meteorological and dendrochronological records for the area.

1992-12-01

171

Effect of knee joint cooling on the electromyographic activity of lower extremity muscles during a plyometric exercise  

British Library Electronic Table of Contents (United Kingdom)

During sporting events, injured athletes often return to competition after icing because of the reduction in pain. Although some controversy exists, several studies suggest that cryotherapy causes a decrease in muscle activity, which may lead to a higher risk of injury upon return to play. The purpose of this study was to investigate the effect of a 20-min knee joint cryotherapy application on the electromyographic activity of leg muscles during a single-leg drop jump in twenty healthy subjects, randomly assigned to an experimental and a control group. After the pre-tests, a crushed-ice bag was applied to the knee joint of the experimental group subjects for 20min, while the control group subjects rested for 20min. All subjects were retested immediately after this period and retested again...

2010-01-01

172

Burning ice. Methane hydrate on the sea floor; Brennendes Eis. Methanhydrat am Meeresgrund  

Energy Technology Data Exchange (ETDEWEB)

In certain regions of the sea floor, water and methane from organic depositions have turned into a burnable form of ice, i.e. methane hydrates which contain more stored energy than all fossil fuel reserves. If they should desintegrate as a result of global heating, methane will be released and will contribute to further global heating. [Deutsch] Im Boden bestimmter Meeresregionen haben sich Wasser und Methan aus organischen Ablagerungen zu einer brennbaren Form von Eis vereinigt. Diese Methanhydrate speichern mehr Energie als alle fossilen Brennstoffvorraete. Wenn sie sich bei einer globalen Erwaermung zersetzen, koennte das entweichende Methan als Treibhausgas die Erde noch mehr aufheizen. (orig.)

1999-06-01

173

Improvement in mechanical properties of magnesium alloy (AZ31) sheet fabricated by casting and subsequent plastic working  

Energy Technology Data Exchange (ETDEWEB)

In order to enhance the mechanical properties of magnesium alloy (AZ31) sheet, an integrated sheet-making process including billet casting, extrusion and rolling was attempted. Microstructural analysis was carried out and the mechanical properties at each processing step were also investigated by tensile tests. By an extrusion process of ingot-processed billet, average grain size of billet was reduced from 91.2 to 28.2 {mu}m, and a further reduction in grain size to 16.9 {mu}m was obtained by subsequent rolling of extruded 5 mm thin slab. In the final step, a rolled sheet of 1 mm showed a remarkable refinement in grain size down to 8.8 {mu}m. Regarding mechanical properties, tensile strength and elongation for as-cast billet, as-extruded thin slab and as-rolled sheet increased from 189, 258 to 234 MPa, and from 13, 16.5 to 23%, respectively. (orig.)

2003-07-01

174

Electrochemical and chemical dissolution behavior of Zn-Fe alloy coatings and its application to the analysis of Zn-Fe alloy layer. Zn-Fe kei mekki so no bunkyokuter dot yokai kyodo to teiryo bunseki eno oyo  

Energy Technology Data Exchange (ETDEWEB)

As surface treated steel sheets, steel sheets with Zn-Fe coatings as well as double-layer steel sheets with Fe-P alloy coatings on Zn-Fe alloy coatings are often used practically. Two treatment methods, which are used to dissolve only alloy layers without dissolving steel sheets in order to find amount and composition of alloy layersr have already been reported. This report investigates the mechanisms of these methods, particularly the mechanisms to control dissolution of steel sheets. In the alkali-dissolution method, Zn-Fe alloy coatings are dissolved in a strong alkaline solution(NaOH-triethanolamine (TEA)-H{sub 2}O{sub 2}). In this case, steel sheets are insoluble because passive films are formed on the surface. In the cathodic polarization electrolysis method, alloy layers are electrolyzed({minus}l.2V) and dissolved in an ammonium nitrate-0-phen ...

1991-11-01

175

Water | Editorial Board  

Wastenet

...Tota-MaharajE-Mail: Interests: water and wastewater treatment, environmental engineering and sustainable systems; sustainable water management; sustainable urban drainage systems (SUDS); combined renewable energy applications with reverse osmosis desalination; microbial fuel cells for bioenergy production and treatment of urban wastewater; solar photocatalytic treatment and disinfection of water/wastewater Dr. Simon Toze CSIRO Land and Water, Queensland Bioscience Precinct - St Lucia, 306 Carmody Road, St Lucia QLD 4067,...

176

Quarterly technical progress report - base program on energy related research. Quarterly report, May 1--July 31, 1994  

Energy Technology Data Exchange (ETDEWEB)

Research is presented on oil and gas technologies, advanced systems, soil remediation and remediation of acid mine drainage, applied science research in plastics and petroleum coprocessing, and fossil fuel and hydrocarbon conversion using a hydrogen rich plasmas.

1997-05-01

177

Integrating Phytoextraction and Biofortification: Fungal Accumulation of Selenium in Plant Materials from Phytoremediation of Agricultural Drainage  

Science.gov (United States)

The phytomanagement of Se-polluted soil and water is one strategy that may be environmentally sustainable and cost-effective for soils and waters enriched with natural-occurring Se. Several plant species, including Indian mustard (Brassica juncea), pickleweed (Salicornia bigelovii), and other salt/S...

178

Glacial geology of the West Tensleep Drainage Basin, Bighorn Mountains, Wyoming  

Energy Technology Data Exchange (ETDEWEB)

The glacial deposits of the West Tensleep Basin in the Bighorn Mountains of Wyoming are mapped and a relative chromology established. The deposits are correlated with the regional model as defined in the Wind River Mountains. A statistical analysis is performed on the density and weathering characteristics of the surficial boulders to determine their validity as indicators of relative age. (ACR)

1980-08-01

179

Estimates of the hydrologic impact of drilling water on core samples taken from partially saturated densely welded tuff  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work is to determine the extent to which drill water might be expected to be imbibed by core samples taken from densely welded tuff. In a related experimental study conducted in G-Tunnel, drill water imbibition by the core samples was observed to be minimal. Calculations were carried out with the TOUGH code with the intent of corroborating the imbibition observations. Due to the absence of hydrologic data pertaining directly to G-Tunnel welded tuff, it was necessary to apply data from a similar formation. Because the moisture retention curve was not available for imbibition conditions, the drainage curve was applied to the model. The poor agreement between the observed and calculated imbibition data is attributed primarily to the inappropriateness of the drainage curve. Also significant is the value of absolute permeability (k) assumed in the model. Provided that the semi-log plot of the drainage and ...

1987-09-01

180

Biosorption for the separation of radionuclides from drainage and process waters of the uranium mining industry  

Energy Technology Data Exchange (ETDEWEB)

Biosorption means the storage of substances at the cell envelope. Different microbial biomasses were tested for the separation of radionuclides from mining waters. Results of a pilot plant demonstrate the ability of these techniques for water cleaning processes. An effluent concentration of lower than 1 mg/l (in most cases 0.1 mg/1) could be realized in a pilot plant by using pure cells of a methylotrophic strain of bacteria as well as using of a fungal mycelia.

1995-12-31

181

The glacial inception as recorded in the NorthGRIP Greenland ice core: timing, structure and associated abrupt temperature changes  

Energy Technology Data Exchange (ETDEWEB)

The mechanisms involved in the glacial inception are still poorly constrained due to a lack of high resolution and cross-dated climate records at various locations. Using air isotopic measurements in the recently drilled NorthGRIP ice core, we show that no evidence exists for stratigraphic disturbance of the climate record of the last glacial inception ({proportional_to}123-100 kyears BP) encompassing Dansgaard-Oeschger events (DO) 25, 24 and 23, even if we lack sufficient resolution to completely rule out disturbance over DO 25. We quantify the rapid surface temperature variability over DO 23 and 24 with associated warmings of 10{+-}2.5 and 16{+-}2.5 C, amplitudes which mimic those observed in full glacial conditions. We use records of {delta}{sup 18}O of O{sub 2} to propose a common timescale for the NorthGRIP and the Antarctic Vostok ice cores, with a maximum uncertainty of 2,500 years, and to examine the interhemispheric sequence of events ...

2006-02-01

182

Technical-ecologic principles of efficient use of open pit mine motor transport  

Energy Technology Data Exchange (ETDEWEB)

The effect of open pit mine motor transport with ICE on the air basin is examined using the example of shale mines and open pits of the production association ''Estonslanets''. Efficient areas of use of different types of open pit mine motor transport, diesel-trolley tracks and electric cars are determined based on technical-economic and ecologic feasibility.

1981-01-01

183

Modelling the spatial and temporal evolution of winter glacier mass balance.  

Environmental Research Database

DescriptionChanges in glacier mass balance are critically influenced by the distribution of snow accumulation at the start of the melt season, but models of the winter season lag seriously behind those of the melt season. The overall aim is to test physically-based models of the spatial and temporal evolution of the winter snowpack at a temperate ice cap (Langjokull, Iceland), to assess how effectively and also how efficiently they capture variation in winter accumulation. A three-step modelling approach i [continued...

2004-01-31

184

Modeling Radar Scattering from the Lunar Surface and Analysis of the Effect of Roughness and Ice Inclusions on CPR Values  

Science.gov (United States)

We developed a model for radar scattering from the lunar reoglith layer using vector radiative transfer theory. From this model, both the radar backscattering coefficient and the circular polarization ratio can be predicted analytically as a function of regolith parameters.

2010-03-01

185

Involving Teachers & Students  

ScienceCinema

...in your blue fuller says global warming summit on the top general information ...this because a lot of times when we talk about global warming and climate change we really focus on the ice ...site ? one organization is called global warming one-on-one and it's run by ...can actually go to global warming one-on-one and and ...something to ? slow global warming but sometimes you feel alone so the big deal if i changed my life ...

186

An idealized numerical simulation of mammatus-like clouds  

British Library Electronic Table of Contents (United Kingdom)

A three-dimensional numerical simulation of mammatus-like clouds is presented. A portion of a cirrus outflow anvil cloud is simulated including cloud ice and snow microphysical representations. The simulated mammatus clouds appear in a cellular pattern and are compared with the few available previously published physical observations of mammatus. Copyright Copyright 2006 Royal Meteorological Society

2006-01-01

187

Tailor die quenching in hot stamping for producing ultra-high strength steel formed parts having strength distribution  

British Library Electronic Table of Contents (United Kingdom)

Tailor die quenching in the hot stamping of quenchable steel sheets was developed to produce ultra-high strength steel formed parts having strength distribution. Local portions of the heated sheet were quenched by holding grooved tools at the bottom dead centre during the stamping. Non-contact portions were generated in the sheet by grooving the tools, and thus the strength in the contact portions is high owing to the quenching and that in the non-contact portions is low owing to the lack of the quenching. Hat-shaped products having a tensile strength of approximately 1.5GPa only at four corners were formed.

2010-01-01

188

One-step synthesis of reduced graphite oxide-silver nanocomposite  

British Library Electronic Table of Contents (United Kingdom)

Here, a general approach for the preparation of reduced graphite oxide (rGO)-silver nanocomposite has been investigated. Graphite oxide (GO) sheets are used as the nanoscale substrates for the formation of rGO-silver composite. GO sheets and Ag ions can be reduced at the same time, under a mild condition using l-ascorbic acid (l-AA) as reducing agent. This simple approach should find practical applications in the production of rGO-silver nanocomposite. The SEM analysis indicates that the silver particles are dispersed on graphene sheets. Raman signals of rGO in the composite are increased by the attached silver nanoparticles, displaying surface-enhanced Raman scattering activity. The degree of enhancement can be adjusted by varying the quantity of silver nanoparticles in the composite. In ...

2011-01-01

189

Influence of recycling and temperature on the swelling ability of paper  

British Library Electronic Table of Contents (United Kingdom)

Hornification is the loss of fiber wall swelling which is detrimental to subsequent recycling resulting from drying. It is known that dried fibers lose their conformability and swelling capacity. The effect of recycling treatment on the swelling ability of hardwood bleached kraft pulp fibers was determined. Modelling paper recycling, sheets were recycled using heat treatment (23?C, 60?C, 100?C). The results were compared with those for natural fibers from bleached kraft pulp. Swelling kinetics of sheets was measured by a modified method monitoring interactions of pulp with water. Swelling ability decreased during the recycling in comparison with never-recycled pulp at all temperatures. Recycling of sheets caused only small changes in the cupri-ethylene-diamine viscosity, however, the water...

2011-01-01

190

Grain size effects on the tensile properties and deformation mechanisms of a magnesium alloy, AZ31B, sheet  

International Nuclear Information System (INIS)

The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic slip systems.

2008-07-15

191

Forced convective heat transfer in cross-corrugated solar air heaters  

Science.gov (United States)

Forced convective heat transfer in a cross-corrugated channel solar air heater has been studied experimentally using air as a working fluid. The channel was formed by two transversely positioned corrugated sheets and two flat thermally insulated side walls. One corrugated sheet was heated by a radiant heater, while the other was thermally insulated. The fluid velocity and temperature, and the wall temperature and the local heat flux across the heated corrugated sheet were measured for a variety of operating flow rates. Experimental results for the channel geometry have yielded the correlation Nu = 0.0743 (Re)[sup 0.76]. This heat-transfer coefficient is about 2.8 times that of a smooth flat channel. The experiments showed that local heat transfer rate was smaller on the valley of the corrugation than that on the peak. The ratio of the local heat transfer rates on the two locations was related to the Reynolds number.

1994-11-01

192

Volumetrical Characterization of Sheet Molding Compounds  

Wastenet

October 2010; in revised form: 12 November 2010 / Accepted: 30 November 2010 / Published: 1 December 2010 Abstract: For a comprehensive study ...1.Introduction ...In a previous work [1], it has been demonstrated that the prepreg composition, molding

193

USGS Fact Sheet 040-02  

Science.gov (United States)

and streambed sediment samples 2-6. Graphs showing: 2. Cesium-137 profile in HOE core 3. PAH trends in Lake Houston cores 4. DDE trends in Lake Houston cores 5. Trends in six trace...

2011-08-27

194

Texas - Energy Collaborations Working for the Environment  

Energy Technology Data Exchange (ETDEWEB)

This fact sheet highlights how renewable energy and energy efficiency technologies can and are being used to reduce air emissions and meet environmental goals, showcasing case studies and technology-specific topics.

2007-12-01

195

Study of nuclear materials by neutron scattering.  

Science.gov (United States)

Following studies on fiber and sheet texture of hexagonal crystal system in 1988, work has been extended to tube texture. Using the zircaloy-4 fuel cladding of Wolsung-type reactor as specimen, six pole figures for different crystallographic planes were m...

1990-01-01

196

State-of-the-art techniques for internal quality measurements in steel sheets production processes; Hakkoban seizo ni okeru naibu hinshitsu no onrain keisoku oyobi kensa gijutsu  

Energy Technology Data Exchange (ETDEWEB)

In this paper, the state-of-the-art ultrasonic and magnetic measuring techniques developed at Kawasaki Steel and used in the production process of steel sheets are described. Representative examples shown here are as follows: (1) Magnetic flux leakage testing system for the detection of nonmetallic inclusions, (2) Nondestructive orientation measurement for secondary re-crystallized grains in grain-oriented electrical steel by ultrasonic interferometry, (3) Immersion testing method for the detection of nonmetallic inclusions, (4) Surface wave probe for the detection of surface flaws in rolls used in rolling mills. Developments of these techniques and their applications to actual steel sheets production processes have contributed to advance in technologies for quality assurance and control. With the help of these techniques, steel sheet products with advanced and uniform properties are being continuously produced to meet ...

1999-12-01

197

Review and Understanding of Screen-Printed Contacts and Selective-Emitter Formation: Preprint  

Energy Technology Data Exchange (ETDEWEB)

A comparison of the loss mechanisms in screen-printed solar cells relative to buried contact cells and cells with photolithography-defined contacts is presented in this paper. Model calculations show that emitter recombination accounts for about 0.5% absolute efficiency loss in conventional screen-printed cells with low-sheet-resistance emitters. Ohmic contact to high-sheet-resistance emitters by screen-printing has been investigated to regain this efficiency loss. Our work shows that good quality ohmic contacts to high sheet-resistance emitters can be achieved if the glass frit chemistry and Ag particle size are carefully tailored. The melting characteristics of the glass frit determine the firing scheme suitable for low contact resistance and high fill factors. In addition, small to regular Ag particles were found to help achieve a higher open-circuit voltage and maintain a low contact resistance. This work has resulted ...

2004-08-01

198

Passive biaxial mechanical properties of isolated canine myocardium.  

UK PubMed Central (United Kingdom)

Excised sheets of canine myocardium were subjected to cyclic loading and unloading in the predominant fibre and cross-fibre directions to determine passive mechanical properties. Myocardium under biaxial...Full Text Available

1983-06-01

199

Numerical Modeling of Magnesium Alloy Sheet Metal Forming at Elevated Temperature  

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, numerical modelling was conducted. The experiment results ...

2007-05-17

200

Nuclear data sheets update for A = 203  

Energy Technology Data Exchange (ETDEWEB)

Experimental results of nuclear reaction and radiative decay for A = 203 nuclides are evaluated. Adopted properties for all the nine isobars, Au, Hg, Tl, Pb, Bi, Po, At, Rn, Fr of mass 203 are presented. Nothing is yet known for [sup 203]Os. 96 refs.

1993-09-01

201

Nuclear data sheets update for A = 203  

International Nuclear Information System (INIS)

Experimental results of nuclear reaction and radiative decay for A = 203 nuclides are evaluated. Adopted properties for all the nine isobars, Au, Hg, Tl, Pb, Bi, Po, At, Rn, Fr of mass 203 are presented. Nothing is yet known for "2"0"3Os. 96 refs.

202

Nuclear data sheets update for A = 101  

Science.gov (United States)

The 1985 evaluation of A = 1-1 (85B1114) has been revised. Experimental information is presented from the neutron-rich {sup 101}Sr to the neutron-deficient {sup 101}In.

1991-06-01

203

Nuclear data sheets update for A = 101  

International Nuclear Information System (INIS)

The 1985 evaluation of A = 1-1 (85B1114) has been revised. Experimental information is presented from the neutron-rich "1"0"1Sr to the neutron-deficient "1"0"1In.

204

Nuclear data sheets for A=101  

International Nuclear Information System (INIS)

Nuclear structure information available to May 1979 has been reviewed. The level properties obtained from decay and reaction experiments are shown in the drawings. Experimental methods, references, and comments are given in the text.

205

Nuclear data sheets for A = 242  

Energy Technology Data Exchange (ETDEWEB)

Detailed level and decay schemes and the experimental reaction and decay data on which they are based are presented for nuclei with mass number A = 242; the experimental data are evaluated. Adopted values for level and ..gamma..-ray energies, ..gamma..-intensities, as well as other nuclear properties are given.

1985-07-01

206

Nuclear data sheets for A = 242  

International Nuclear Information System (INIS)

Detailed level and decay schemes and the experimental reaction and decay data on which they are based are presented for nuclei with mass number A = 242; the experimental data are evaluated. Adopted values for level and #gamma#-ray energies, #gamma#-intensities, as well as other nuclear properties are given.

207

Nuclear Data Sheets for A = 66  

International Nuclear Information System (INIS)

The evaluators present in this publication spectroscopic data and level schemes from radioactive decay and nuclear reactions studies for all isobars with mass number A = 66. The first level- scheme of "6"6As, from (HI,xn#gamma#), has been included in this evaluation.

2010-04-01

208

NMR studies of Borrelia burgdorferi OspA, a 28 kDa protein containing a single-layer #beta#-sheet  

International Nuclear Information System (INIS)

The crystal structure of outer surface protein A (OspA) from Borrelia burgdorferi contains a single-layer #beta#-sheet connecting the N- and C-terminal globular domains. The central #beta#-sheet consists largely of polar amino acids and it is solvent-exposed on both faces, which so far appears to be unique among known protein structures. We have accomplished nearly complete backbone H, C and N and C";/H"#beta# assignments of OspA (28 kDa) using standard triple resonance techniques without perdeuteration. This was made possible by recording spectra at a high temperature (45 "oC ). The chemical shift index and "1"5N T_1/T_2 ratios show that both the secondary structure and the global conformation of OspA in solution are similar to the crystal structure, suggesting that the unique central #beta#-sheet is fairly rigid.

1998-05-01

209

HCN polymers characterized by solid state NMR: Chains and sheets formed in the neat liquid  

UK PubMed Central (United Kingdom)

Hydrogen cyanide polymerizes readily under a variety of conditions and significant prebiotic roles have been suggested for these polymers due to the abundance of HCN in universe. However, the structures...Full Text Available

2009-04-07

210

Further assembly required: construction and dynamics of the endoplasmic reticulum network  

UK PubMed Central (United Kingdom)

The endoplasmic reticulum (ER) is a continuous membrane system comprising the nuclear envelope, ribosome-studded peripheral sheets and an interconnected network of smooth tubules extending throughout...Full Text Available

2010-07-01

211

Functionalized Vegetable Oils for Utilization as Polymer Building Blocks: Office of Industrial Technologies (OIT) Agriculture Project Fact Sheet  

Energy Technology Data Exchange (ETDEWEB)

Vegetable oils such as soybean oil will be converted to novel polymers using hydroformylation and other catalytic processes. These polymers can be used in the construction, automotive, packaging, and electronic sectors.

2001-09-12

212

Energy balances of OECD countries 1985/1986  

Energy Technology Data Exchange (ETDEWEB)

Provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD countries as well as the regions: OECD total, IEA, North America, Pacific, OECD Europe, EEC and Yugoslavia.

1988-01-01

213

Donors' Fact Sheets: EBRD  

Wastenet

...Goods: promote the protection of ldquo;natural parks and reserves, mangroves, reefs and lagoons,rdquo; and ldquo;expanding forest cover and tree integration with agricultural production systems rdquo;; climate change will be reduced through the trading of pollution permits under the Kyoto Protocol. Enhancing Disaster Management Capabilities:...

214

Nuclear Data Sheets for A = 177  

Energy Technology Data Exchange (ETDEWEB)

Evaluated spectroscopic data for all nuclei with mass number A = 177 and corresponding level schemes from radioactive decay and reaction studies are presented. Most of the new information since the previous evaluation of this mass chain consists of the decay of the recently discovered isotope [sup 177]Tm, and the level structure of [sup 177]Ir, [sup 177]Os, and [sup 177]Pt. The present evaluation supersedes the earlier one by Y. A. Ellis and B. Harmatz (75E107) published in Nuclear Data Sheets 16, 135 (1975).

1993-03-01

215

Nuclear Data Sheets for A = 177  

International Nuclear Information System (INIS)

Evaluated spectroscopic data for all nuclei with mass number A = 177 and corresponding level schemes from radioactive decay and reaction studies are presented. Most of the new information since the previous evaluation of this mass chain consists of the decay of the recently discovered isotope "1"7"7Tm, and the level structure of "1"7"7Ir, "1"7"7Os, and "1"7"7Pt. The present evaluation supersedes the earlier one by Y. A. Ellis and B. Harmatz (75E107) published in Nuclear Data Sheets 16, 135 (1975).

216

Improved formability of ultra high strength steels through local heat treatment  

Energy Technology Data Exchange (ETDEWEB)

In this paper it is described how a martensitic steel sheet with tensile strength of 1400 MPa is heat treated locally. The sheet is then formed in the heat treated regions in a way that would be impossible with the untreated material. Mechanical properties and forming limit diagrams of the heat treated material are determined and the forming operations are simulated, which shows that the method can be used by designers. Although the method has been known for decades, it remains to be industrialised and the work presented here is to be seen as a contribution to this development. (orig.)

2005-07-01

217

A new calculation of the cosmic-ray antiproton spectrum in the Galaxy and heliospheric modulation effects on this spectrum using a drift plus wavy current sheet model  

Energy Technology Data Exchange (ETDEWEB)

The expected interstellar antiproton spectrum arising from cosmic-ray interactions in the Galaxy is recalculated, and the modulation of both antiprotons and protons is calculated using a two-dimensional modulation model incorporating gradient and curvature drifts and a wavy current sheet as well as the usual diffusion, convection, and energy-loss effects. Significant differences in the antiproton/proton ratio for different solar magnetic field polarities are predicted as well as a 'low-energy' component for antiprotons below about 1 GeV. 28 refs.

1989-09-01

218

A high-power millimeter-wave sheet beam free-electron laser amplifier  

International Nuclear Information System (INIS)

The results of experiments with a short period (9.6 mm) wiggler sheet electron beam (1.0 mm x 2.0 cm) millimeter-wave free electron laser (FEL) amplifier are presented. This FEL amplifier utilized a strong wiggler field for sheet beam confinement in the narrow beam dimension and an offset-pole side-focusing technique for the wide dimension beam confinement. The beam analysis herein includes finite emittance and space-charge effects. High-current beam propagation was achieved as a result of extensive analytical studies and experimental optimization. A design optimization resulted in a low sensitivity to structure errors and beam velocity spread, as well as a low required beam energy. A maximum gain of 24 dB was achieved with a 1-kW injected signal power at 86 GHz, a 450-kV beam voltage, 17-A beam current, 3.8-kG wiggler magnetic field, and a 74-period wiggler length. The maximum gain with a one-watt injected millimeter-wave power was observed to ...

219

The behavior of waste rock piles; Le comportement des haldes de steriles  

Energy Technology Data Exchange (ETDEWEB)

Under the auspices of the Mine Environment Neutral Drainage (MEND) Program, several waste rock piles were monitored and characterized. Acid rock drainage (ARD) became a mechanism better understood based on the data acquired during these projects. Numerical simulation was used to better comprehend the quantitative issues associated with the characterization of three specific sites for the purpose of this study. The sites selected were the south waste rock pile of the Doyon Mine in Quebec, the Northdale of the mining district of Ronnenberg in Germany, and the waste rock pile of the Sugar Shack South of the Questa mine in New Mexico. The observed and simulated conditions were very distinct from one mine to another, even if the same mechanisms were involved. The dominant oxygen and heat transfer mechanisms displayed the most varied behavior between the sites. ARD control or site rehabilitation decisions were based on the quantitative understanding ...

2000-07-01

220

The Polytechnique, UQAT, NSERC chair in environment and tailings management; La Chaire Polytechnique, UQAT, CRSNG en environnement et gestion des rejets miniers  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this new industrial chair is to ensure the continuation and development of new research activities in the field of environment protection as it relates to the good management of mine tailings. The mining industry plays a vital role in the economy of a number of regions in both Quebec and Canada and also causes environmental problems due to the generation of liquid, solid, and gaseous wastes. Mine tailings can cause acid mine drainage. This acid mine drainage (AMD) can have detrimental effects on the ecosystems adjoining tailings or waste rock piles. We must remain aware that some of the remedial measures instituted to contain AMD might cause problems due to their possible instability. Despite the fact that instability is a rare occurrence, it can have disastrous effects on the environment as demonstrated in Spain, Guyana, and the Philippines during the last few years. The creation of this chair in environment and tailings ...

2000-07-01

221

Soil heterogeneity effects on O2 distribution and CH4 emissions from wetlands: In situ and mesocosm studies with planar O2 optodes and membrane inlet mass spectrometry  

British Library Electronic Table of Contents (United Kingdom)

The importance of soil heterogeneity for methane emission from a wetland soil is assessed by in situ point measurements of depth-specific O2 and CH4 concentrations and simultaneous soil CH4 fluxes at contrasting water levels. Profile measurements, and associated assumptions in their interpretation, were validated in a controlled mesocosm drainage and saturation experiment applying planar O2 optodes and membrane inlet mass spectrometry. Results show that peat soil is heterogeneous containing dynamic macropore systems created by both macrofauna and flora, which facilitate preferential flow of water, O2 and CH4 and vary temporally with changes in the moisture regime. The O2 content above the water table after drainage varied horizontally from 0 to 100% air saturation within few mm. Oxic zones...

2010-01-01

222

Real-time management of water quality in the San Joaquin River Basin, California.  

Energy Technology Data Exchange (ETDEWEB)

In the San Joaquin River Basin, California, a realtime water quality forecasting model was developed to help improve the management of saline agricultural and wetland drainage to meet water quality objectives. Predicted salt loads from the water quality forecasting model, SJRIODAY, were consistently within +- 11 percent of actual, within +- 14 percent for seven-day forecasts, and with in +- 26 percent for 14-day forecasts for the 16-month trial period. When the 48 days dominated by rainfall/runoff events were eliminated from the data set, the error bar decreased to +- 9 percent for the model and +- 11 percent and +- 17 percent for the seven-day and 14-day forecasts, respectively. Constraints on the use of the model for salinity management on the San Joaquin River include the number of entities that control or influence water quality and the lack of a centralized authority to direct their activities. The lack of real-time monitoring sensors for other primary ...

1997-09-01

223

Mine waste disposal and managements  

Energy Technology Data Exchange (ETDEWEB)

Acid Rock Drainage (ARD) is the product formed by the atmospheric oxidation of the relatively common pyrite and pyrrhotite. Waste rock dumps and tailings containing sulfide mineral have been reported at toxic materials producing ARD. Mining in sulphide bearing rock is one of activity which may lead to generation and release of ARD. ARD has had some major detrimental affects on mining areas. The purpose of this study was carried out to develop disposal method for preventing contamination of water and soil environment by waste rocks dump and tailings, which could discharge the acid drainage with high level of metals. Scope of this study was as following: environmental impacts by mine wastes, geochemical characteristics such as metal speciation, acid potential and paste pH of mine wastes, interpretation of occurrence of ARD underneath tailings impoundment, analysis of slope stability of tailings dam etc. The following procedures were used as part ...

1998-12-01

224

Impact of climate change on carbon cycle in freshwater ecosystems  

Energy Technology Data Exchange (ETDEWEB)

The impacts of the expected climate change on Finnish lake ecosystems were studied with the biota of the mesohumic Lake Paeaejaervi, southern Finland. Experimental conditions, from small-scale experiments on single species level to a large-scale ecosystem manipulation, were established to simulate directly the future climate and/or loading of nutrients and dissolved organic matter (DOM) from the drainage area. The experimental studies were accomplished by modelling the carbon flow in the pelagic food web as well as the growth of littoral macrophytes. The main hypothese tested were as follows: As a consequence of the climate change (rising temperature and increasing precipitation) the loading of nutrients and dissolved organic matter (DOM) from the drainage area to the lake will increase. In the pelagic zone this will be first reflected i higher productivity of primary producers and bacteria, but will later affect the entire food chain. Increase ...

1996-12-31

225

Further development of excentric screw pumps for reduction of fluid levels in gas wells; Weiterentwicklung von Exzenterschneckenpumpen zur Fluessigkeitsspiegelabsenkung in Gasbohrungen  

Energy Technology Data Exchange (ETDEWEB)

Beside sucker-rod-type pumps and submersible centrifugal pumps, excentric screw pumps (so-called progressing cavity pumps) belong to standard conveyors in the production of crude oil. The authors of the contribution under consideration present the further development of excentric screw pumps with respect to the reduction of fluid levels in gas wells. This further development is based on a co-operation between the operator (Rohoel Aufsuchungs AG (Gampern, Austria)), the pump supplier (NETZSCH Oilfield Products GmbH (Selb, Federal Republic of Germany)) and the Institute for Process Technologies and Machinery at the University of Erlangen-Nuernberg (Federal Republic of Germany). The authors report on first attempts with the excentric screw pump at Weizberg (Federal Republic of Germany), material investigations at the University of Erlangen-Nuernberg, optimization of pump components and pump systems as well as on the optimization of the entire drainage process. ...

2008-10-23

226

Effects of freeze-thaw cycles on the performance of soft materials used in soil covers with capillary barrier; Effets des cycles de gel-degel sur la performance des materiaux meubles utilises dans les couvertures a effets de barriere capillaire  

Energy Technology Data Exchange (ETDEWEB)

Freezing and thaw have an effect on soils, and the effect of the freeze-thaw cycle on soil covers used in the control of acid mine drainage was discussed in this poster presentation. The purpose of soil covers in cases involving acid mine drainage (AMD) is to reduce the exposure of tailings to oxygen which cause AMD. The effect of this freezing-thaw cycle on soft materials used in soil covers with capillary effect was studied. Some laboratory experiments were conducted to evaluate the properties of the moisture retention layer. The preliminary results were presented. The results indicated that the freeze-thaw cycle might affect the performance of soil covers in the long term, depending on the type of materials selected. Further research is undergoing. 26 figs.

2000-07-01

227

Diagnosis for the cancer extension of cholangiocarcinoma. The current status  

International Nuclear Information System (INIS)

Described is the diagnosis for the cancer extension of cholangiocarcinoma by various imaging techniques and processes to support the current surgical procedure based on preoperative biliary drainage. The cancer tends to locally extend horizontally and/or vertically and its diagnosis is important for surgical indication. For the indication, multi-detector raw CT (MDCT) and MR cholangio-pancreatography (MRCP) are useful and particularly, the former can give multi-phase (arterial, portal and delayed) images to reconstruct multiplanar (MPR) and CT angiographic 3D images, which have made the previous invasive examinations like angiography and percutaneous transportal contrasting unnecessary. MDCT and MRCP can almost complete the diagnosis of the extension. The operative procedure is decided dependently on the site of the lesion, and of which diagnosis, whether it is hepatic hilar/on upper bile duct or middle/lower ductal, is different. MDCT-MPR and MRCP are virtually ...

2010-07-01

228

Development of a GIUH model based on river fractal characteristics  

Energy Technology Data Exchange (ETDEWEB)

The geometric patterns of a stream network in a drainage basin can be viewed as a 'fractal' with fractal dimensions. Fractals provide a mathematical framework for treatment of irregular, ostensively complex shapes that show similar patterns or geometric characteristics over a range of scale. GIUH (Geomorphological Instantaneous Unit Hydrograph) is based on the hydrologic response of surface runoff in a catchment basin. This model incorporates geomorphologic parameters of a basin using Horton's order ratios. For an ordered drainage system, the fractal dimensions can be derived from Horton's laws of stream numbers, stream lengths and stream areas. In this paper, a fractal approach, which is leading to representation of a 2-parameter Gamma distribution type GIUH, has been carried out to incorporate the self-similarity of the channel networks based on the high correlations between the Horton's order ...

1999-10-31

229

Cooperative Research Centre for Mining Technology and Equipment (CMTE) annual report 1998/99  

Energy Technology Data Exchange (ETDEWEB)

The Centre's new structure, implemented in July 1997 is now operating well. CMTE Development Limited is now the legal entity for the CRC and replaces the previously unincorporated joint venture. CMTE has ten core participating organisations. Roche Highwall Mining Pty. Ltd., withdrew participation during the year. The annual report describes its structure and management and various cooperative links. It outlines research programs in the following areas: mining; geological sensing; automation; reliability and maintenance; and coal processing. Projects include: developing an ultra-short-radius drilling machine for drainage of methane gas from coal seams; developing techniques for improved drilling speed and accuracy to reduce costs for gas drainage holes in underground coal mining; developing draglines; developing geophysical logging tools; developing autonomous control of underground vehicles such as coal-haul-dump (LHD) and haulage ...

1999-07-01

230

Column leaching test to evaluate the use of alkaline industrial wastes to neutralize acid mine tailings  

Energy Technology Data Exchange (ETDEWEB)

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals that releases highly acidic, sulfate, and metals-rich drainage. In this study, alkaline industrial wastes were mixed with acid mine tailings in order to obtain neutral conditions. A series of column leaching tests were performed to evaluate the behavior of reactive mine tailings amended with alkaline-additions under dynamic conditions. Column tests were conducted of oxidized mine tailings combined with cement kiln dust, red mud bauxite, and mixtures of cement kiln dust with red mud bauxite. The pH results show the addition of 10% of alkaline materials permits the maintenance of near neutral conditions. In the presence of 10% alkaline material, the concentration of toxic metals such as Al, Cu, Fe, Zn are significantly reduced as well as the number of viable cells (Thiobacillus ferrooxidans) compared to control samples.

2005-08-01

231

CT diagnosis of subphrenic abscess after splenectomy for trauma; Ruolo della tomografia computerizzata nella valutazione degli ascessi subfrenici dopo splenectomia post-traumatica  

Energy Technology Data Exchange (ETDEWEB)

The paper studies subphrenic inflammatory abscesses and splenic fluid collections after splenectomy for trauma. These complications may appear early or late postoperatively; they are easily demonstrated with computerized tomography, which permits accurate spatial assessment of the lesions and appropriate treatment with percutaneous drainage. It has been also investigates the diagnostic accuracy of the CT in subphrenic inflammatory conditions after emergency splenectomy for traumatic spleen rupture and found that CT is a precious tool for rapid and easy diagnosis and follow-up of subphrenic abscesses treated with percutaneous drainage. [Italian] Scopo del lavoro e' di valutare il ruolo della tomografia computerizzata nelle flogrosi subfreniche secondarie a splenectomia d'urgenza per rottura traumatica della milza, documentando come tale metodica risulti accurata nel diagnosticare e monitorare in modo semplice e rapido ...

1999-09-01

232

Study of solution for issues of an optimum operating plan in heat storing system; Chikunetsu system ni okeru saiteki un`yo keikaku mondai no kaiho ni taisuru ichikosatsu  

Energy Technology Data Exchange (ETDEWEB)

An approximate solution was proposed in which a sensitivity analysis by the storage and release of heat was performed for the subject issues and in which an operating method was thereby determined for the equipment constituting the system by means of a linear programming. Accordingly, a heat storage type energy supply system for a district cooling and heating was taken up as a concrete object to be examined. This system consisted of a gas turbine generator, initial power receiving equipment, gas boiler, electric heat pump for ice heat storage, cooling tower, heat exchanger, steam absorbing refrigerating machine, ice heat storage tank, cold and warm water heat storage tank, etc. As a result of comparison between the proposed method and the resolving method, the former showed -0.92 to 2.58% in the increase in the operating cost compared with the latter. A case where the operating cost of the resolving method was sometimes larger than the proposed ...

1996-02-01

233

Natural climate variability as indicated by glaciers and implications for climate change: a modeling study  

Energy Technology Data Exchange (ETDEWEB)

Glacier fluctuations exclusively due to internal variations in the climate system are simulated using downscaled integrations of the ECHAM4/OPYC coupled general circulation model (GCM). A process-based modeling approach using a mass balance model of intermediate complexity and a dynamic ice flow model considering simple shearing flow and sliding are applied. Multi-millennia records of glacier length fluctuations for Nigardsbreen (Norway) and Rhonegletscher (Switzerland) are simulated using auto-regressive processes determined by statistically downscaled GCM experiments. Return periods and probabilities of specific glacier length changes using GCM integrations excluding external forcings such as solar irradiation changes, volcanic or anthropogenic effects are analyzed and compared to historical glacier length records. Preindustrial fluctuations of the glaciers as far as observed or reconstructed, including their advance during the ''Little ...

2001-08-01

234

Load calculation and system evaluation for electric vehicle climate control  

Energy Technology Data Exchange (ETDEWEB)

This paper presents an analysis of the applicability of alternative systems for electric vehicle (EV) heating and air conditioning (HVAC). The paper consists of two parts. The first part is a cooling and heating load calculation for electric vehicles. The second part is an evaluation of several systems that can provide the desired cooling and heating in EVs. These systems are ranked according to their overall weight The overall weight is calculated by adding the system weight and the weight of the battery necessary to provide energy for system operation. The system with the minimum overall weight is considered to be the best, because minimum vehicle weight decreases the energy required for propulsion, and therefore increases the vehicle range. Three systems are considered as the best choices for EV HVAC. These are, vapor compression, ice storage and adsorption systems. These systems are evaluated, including calculations of system weight, system volume, and COP. The ...

1994-09-12

235

Diffuse high-energy neutrino searches in AMANDA-II and IceCube: results and future prospects  

Energy Technology Data Exchange (ETDEWEB)

The AMANDA-II data collected during the period 2000-2003 have been analysed in a search for a diffuse flux of high-energy extra-terrestrial muon neutrinos from the sum of all sources in the Universe. With no excess events seen, an upper limit of E{sub {nu}}{sup 2} xs dN{sub {nu}}/dE{sub {nu}} < 7.4 x 10{sup -8} GeV cm{sup -2} s{sup -1} sr{sup -1} was obtained. The sensitivity of the diffuse analysis of IceCube 9 string for 137 days of data is calculated to be E{sub {nu}}{sup 2} x dN{sub {nu}}/dE{sub {nu}} < 1.3 x 10{sup -7} GeV cm{sup -2} s{sup -1} sr{sup -1}. No excess events are observed, which confirms the AMANDA-II upper limit.

2008-07-15

236

Cost guide. Volume 6. Cost-estimating methods and techniques  

Energy Technology Data Exchange (ETDEWEB)

There are many requirements for cost analysis and estimating within the Department of Energy (DOE). As projects go through the many stages of planning, source evaluation and selection, contracting, and construction, different estimating requirements exist and different techniques are available to the estimator. This cost guide illustrates how quantity takeoff estimating is performed when adequate design data are available, and it shows how statistics can be applied to obtain parametric cost estimates. Parametric techniques will become increasingly useful as the Department's cost data base and Cost Estimating Relationships (CERs) are developed. Other cost guides developed by the Independent Cost Estimating (ICE) Staff will be published and disseminated soon. The section on parametric cost estimating uses Department of Defense examples since the ICE Staff considered this information to be some of the best available on this subject. Also, ...

1982-05-01

237

Comparison of secondary metabolite production by Penicillium crustosum strains, isolated from Arctic and other various ecological niches.  

Science.gov (United States)

Penicillium crustosum is common in food and feed both in subtropical and temperate regions. Recently, it has also been found occurring frequently in glacier ice, sea ice and sea water of Arctic regions of Svalbard. The aim of the study was to compare isolates of the same fungal species from widely different habitats and geographic regions to see if the nutritional physiology and the profile of secondary metabolites were consistent or depended on the isolation source. All 121 strains examined produced the following families of secondary metabolites: penitrems (100%), roquefortines (100%), terrestric acids (99.2%) and viridicatols (100%), whereas 81 of 83 Arctic isolates additionally produced andrastin A. However, only 8 of 38 non-Arctic isolates produced detectable andrastin A. The quantitative profiles of 96 strains were compared using cluster, principal component and correspondence analyses. There was no clear grouping of Arctic versus ...

2004-12-22

238

Zonal, provincial, lithological, and geomorphic features of soil salinization in the Southern federal okrug of Russia  

British Library Electronic Table of Contents (United Kingdom)

The relationships between soil salinization and the zonal and provincial bioclimatic conditions, the lithological composition of the sediments, and the geomorphic features of the territory have been analyzed for the Southern federal okrug of Russia. It is shown that the lithological and geomorphic conditions (relief, salinity of parent materials, degree of drainage, and the depth of saline groundwater) play an important role in the distribution of salt-affected soils against the background of the more general regularities specified by the climate. The participation of salt-affected soils in the soil cover of the Southern federal okrug increases in the eastward direction from the forest-steppe zone to the semidesert zone in agreement with an increase in the aridity and continentality of the...

2011-01-01

239

Simulation of relative permeability hystersis to the nonwetting phase  

Energy Technology Data Exchange (ETDEWEB)

In reservoir fluid flow, the situation described by an increase in nonwetting phase saturation followed by an increase in wetting phase saturation causes a relative permeability hysteresis effect that is well known. This paper presents a method which allows the calculation of imbibition relative permeability starting at any saturation. The data required are the drainage curve, the historical maximum non wetting saturation, and a minimum of one additional point on some corresponding experimental imbibition curve. In this development, all imbibition curves are shown to be parallel. Also significant is the fact that the residual nonwetting phase saturation can be calculated without a complete experimental specification of the imbibition curve. 5 refs.

1981-01-01

240

Radiation exposure of patients and operators during interventional radiology  

International Nuclear Information System (INIS)

Surface doses received by patients and operators were measured during 30 interventional radiological procedures (ten percutaneous transhepatic biliary drainages, ten percutaneous nephrostomies, ten percutaneous transluminal angioplasties). In addition, organ doses to the patient were determined using an Alderson-Rando phantom. These served as a basis for calculating the so-called somatic dose indices. It was found that the somatic radiation risk to the patient is relatively small despite prolonged periods of fluoroscopy. However, exposure of the hands and lenses of the operator could easily reach the limits thought acceptable while carrying out these procedures with additional angiography. (orig).

1986-01-01

241

Mineral biotechnology. Microbial aspects of mineral beneficiation, metal extraction, and environmental control  

Energy Technology Data Exchange (ETDEWEB)

Papers in this book illustrate the utility of mineral biotechnology with respect to biobeneficiation, bioleaching, bioremediation and biomineralization. Papers of particular interest to the coal industry include: depression of pyrite flotation by yeast and bacteris (S.K. Kawatra and T.C. Eisele); desulfurization of coal by microbial flotation in a semicontinuous system (T. Nagaoka and others); biochemical removal of HAP precursors from coal - INEEL slurry column testing (K.S. Noah and G.J. Olson); microorganisms, biotechnology and acid rock drainage - emphasis on passive-biological control and treatment methods (N. Kuyucak); and utility of bioreagents in mineral processing (P. Somasundaran and others).

2001-07-01

242

Evidence-Based Drainage of Infected Hydronephrosis Secondary to Ureteric Calculi  

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction: The obstructed, infected kidney is a urological emergency. It has been accepted that the management of infected hydronephrosis secondary to ureteric stones is through prompt decompression of the collecting system. However, the optimal method of decompression has yet to be established. Materials and Methods: A PubMed and Medline search was performed of all English-language articles from 1960 using key words ?sepsis,?? ?urosepsis,?? ?obstruction,?? ?obstructive pyelonephritis,?? ?pyonephrosis,?? ?infection and hydronephrosis?? ?decompression,?? ?stent,?? ?nephrostomy,?? and ?management.?? The Cochrane database and National Institute for Clinical Effectiveness guidelines were searched using the terms ?sepsis,?? ?urosepsis,?? ?stent,?? ?nephrostomy,?? or ?obstruction.?? ...

2010-01-01

243

Terra Nova: taming the North Atlantic  

Energy Technology Data Exchange (ETDEWEB)

The Terra Nova offshore oil project is described, with emphasis on the construction of the Terra Nova Floating Production Storage and Offloading (FPSO) vessel, the first such vessel constructed for the harsh environment of the North Atlantic off Newfoundland, the site of an oil field that is expected to produce 125,000 to 150,000 barrels of oil per day starting in 2001. The vessel has a double-hull, made of 3,000 tons of reinforced steel to protect it from ice in the form of massive icebergs or crusty 'packs'. The vessel has the world's largest quick release turret, meaning that the vessel can be quickly disconnected from its turret and mooring in the event of an encroaching iceberg, and then reconnected in an environmentally sound way. Apart from its extremely rugged construction, protecting the FPSO vessel against icebergs is accomplished by way of 'hosing down' (by melting by powerful streams of water) or ...

2000-08-01

244

JEFI OLD: Joint seismic/electrical measurement of gas hydrate content in continental margin sediments  

Environmental Research Database

ObjectivesNot EnteredDescriptionMethane hydrate in an ice-like substance consisting of molecules of methane gas combined chemically with water. It is stable at high pressures and low temperatures. Since the ocean floor is normally cold, but temperatures increase with depth inside the Earth, such conditions normally prevail for a few hundred meters below the seafloor where the ocean depth is more than a few hundred metres. Methane beneath the ocean floor is formed by the decomposition of organic material. At the edges of the co [continued...

2006-01-30

245

Development of superconducting cryo-electron microscope and its applications  

International Nuclear Information System (INIS)

Recently, a superconducting cryo-electron microscope in which specimens are cooled to the liquid helium temperature (4.2 K) has been developed. The main components and functional features of this new microscope are reported together with application data on polyethylene, poly (4-methyl-1-pentene), valonia cellulose, rock salt, ice crystallites and ceramic superconductor. The resistance to electron radiation damage, of beam-sensitive specimens including polymers has been increased more than ten times. Thus, the microscope has made it possible to take high resolution images and to analyze the crystal-structure of micro-areas. (orig.).

1988-01-01

246

Application of fracture mechanics to cementitious composites  

Energy Technology Data Exchange (ETDEWEB)

This work contains 27 chapters which cover recent advances in fracture mechanics applied to cement-based composites: concrete, reinforced concrete, and fiber reinforced concrete. The book, based on a NATO Advanced Study Institute, is a comprehensive survey of treating nonlinearity associated with crack growth in brittle materials such as cement composites, rocks and ice. The book is divided into 8 major themes: advances in nonlinear fracture mechanics; fracture processes; numerical modelling of fracture; experimental methods of determining fracture parameters; damage and continuum modelling; strain-rate and dynamic effects of crack propagation; stress-corrosion, time and temperature effects on fracture; and implications for concrete structures.

1985-01-01

247

A truly commercial product  

International Nuclear Information System (INIS)

In one of the first uses of high Tc superconductors in an end-use product, Lake Shore Cryotronics and a Swiss lab have developed a liquid nitrogen level sensor using a high Tc thin film. The probe is manufactured using a seamless stainless steel tube with an yttrium-based zirconium oxide flame-sprayed on the tube. A plasma-sprayed superconductor compound is deposited on top of that. The probe is coated with a sealant that protects the superconducting film from the atmosphere. This manufacturing method has yielded an extremely durable product. Unaffected by ice formation and related mechanical problems, the superconducting level sensor can be kept in the dewar for long periods of time.

248

Use of man-made impoundment in mitigating acid mine drainage in the North Branch Potomac River  

International Nuclear Information System (INIS)

The US Department of the Army, Baltimore District Corps of Engineers, oversees a long-term monitoring study to assess and evaluate effects of the Jennings-Randolph reservoir on biota in the North Branch Potomac River. The reservoir was intended, in part, to mitigate effects of acid mine drainage originating in upstream and headwater area. The present study assessed recovery of benthos and fish in this system, six years after completion of the reservoir. Higher pH and lower iron and sulfate concentrations were observed upstream of the reservoir compared to preimpoundment conditions, suggesting better overall water quality in the upper North Branch. Water quality improved slightly directly downstream of the reservoir. However, the reservoir itself was poorly colonized by macrophytes and benthic organisms, and plankton composition suggested either metal toxicity and/or nutrient limitation. One large tributary to the North Branch and the reservoir (Stony River) was ...

249

The use of oxygen isotopic composition to study water dynamics in Amazon floodplain lakes  

International Nuclear Information System (INIS)

The lakes formed in the Amazon floodplain play a key role in sustaining the highest populational density in the Amazon Basin because of its high primary productivity. The water volume in these lakes vary greatly during the year and possible water sources are the feeding river during high water state of the hydrographs and local inputs from its drainage basin. As these sources are chemically distinct, to understand the nutrient dynamics in these lakes, it is very important to know the relative water contribution of different water sources. In this paper we use "1"8O as a conservative to know the water sources for the lakes and our hypothesis is that: 1) In the high water stage lake water is derived predominantly from its feeding river. Therefore their #delta#"1"8O should be similar. 2) In the low water stage lake water is a mixture of watershed and last flood event waters. In this case, lake #delta#"1"8O should be indicative of the relative contribution of each ...

1989-05-01

250

Terra Nova FPSO on the Grand Banks of Canada  

Energy Technology Data Exchange (ETDEWEB)

An increased use of floating production facilities for offshore oil production in the past fifteen years was due in part to advances in technology, the opening of new frontiers and the increased emphasis on value driven development. Throughout the world, a total of 121 floating production systems were in operation in February 2001, and orders had been placed for an additional 27. Located near the nose of the Grand Banks, approximately 350 kilometres east-southeast of St. John's, Newfoundland is the Terra Nova development. Twelve years elapsed between the discovery of the field in 1984 and the granting of the approval for development in 1996. The decision was made to use a floating production system as the Terra Nova was not considered robust enough to support a gravity base, ice resistant structure development concept, especially considering that it came on the heels of the Hibernia development. The first Floating Production, Storage and Offloading (FPSO) ...

2001-07-01

251

Fundamental aspects of the freezing of cells, with emphasis on mammalian ova and embryos. (Aspectos fundamentales de la congelacion de celulas, especialmente ovulos y embriones de mamiferos  

Energy Technology Data Exchange (ETDEWEB)

For most cells there exists an optimum cooling rate. Both supraoptimal rates and suboptimal rates can be very damaging. The optimal rate varies enormously from less than or equal to 1/sup 0/C/min for mammalian preimplantation embryos to greater than or equal to 800/sup 0/C/min for the human red cell. Death at supraoptimal rates is the result of the formation of intracellular ice and its recrystallization during warming. Intracellular ice occurs when cells are cooled too rapidly to allow them to equilibrate by the osmotic withdrawal of intracellular water. The definition of too rapid depends chiefly on the size of the cell and its permeability to water. Death at suboptimal rates is a consequence of the major alterations in aqueous solutions produced by ice formation. The chief effects are a major reduction in the fraction of the solution remaining unfrozen at a given temperature and a major increase in the solute ...

1980-01-01

252

Modification of the sheet resistance of ink jet printed polymer conducting films by changing the plastic substrate  

Energy Technology Data Exchange (ETDEWEB)

The ink jet printing technology is a relatively novel technique in development of organic electronic devices. The technique consists of working out depositions of organic layers by a piezo-based ink jet printer. In this work polymer conducting films deposited by ink jet printing technique on different plastic substrates has been demonstrated. The poly(3,4-ethylenedioxythiofene)/poly(4-styrenesulfonate) [PEDOT/PSS] and glycerol-modified PEDOT/PSS [G-PEDOT/PSS] were used like conducting inks to be applied on polyester and polyethylene terephthalate (PET) substrates. By means of the change of substrate associated to the deposition number or type of polymer ink used for printing of the conducting films, the sheet resistance can be modified. Such a behavior suggests that plastic substrate fulfills an important role for the changing of sheet resistance of the PEDOT/PSS and G-PEDOT/PSS films made by ink jet printing technique. Films obtained from this ...

2005-09-25

253

Hawaii demand-side management resource assessment. Final report, Reference Volume 2: Final residential and commercial building prototypes and DOE-2.1E developed UECs and EUIs; Part 3  

Energy Technology Data Exchange (ETDEWEB)

This section contains the detailed measured impact results and market segment data for each DSM case examined for this building type. A complete index of all base and measure cases defined for this building type is shown first. This index represents an expansion of the base and measure matrix presented in Table 1 (residential) or Table 2 (commercial) for the applicable sector. Following this index, a summary report sheet is provided for each DSM measure case in the order shown in the index. The summary report sheet contains a host of information and selected graphs which define and depict the measure impacts and outline the market segment data assumptions utilized for each case in the DBEDT DSM Forecasting models. The variables and figures included in the summary report sheet are described. Numerous tables and figures are included.

1995-04-01

254

Hawaii demand-side management resource assessment. Final report, Reference Volume 2: Final residential and commercial building prototypes and DOE-2.1E developed UECs and EUIs; Part 2  

Energy Technology Data Exchange (ETDEWEB)

This section contains the detailed measured impact results and market segment data for each DSM case examined for this building type. A complete index of all base and measure cases defined for this building type is shown first. This index represents an expansion of the base and measure matrix presented in Table 1 (residential) or Table 2 (commercial) for the applicable sector. Following this index, a summary report sheet is provided for each DSM measure case in the order shown in the index. The summary report sheet contains a host of information and selected graphs which define and depict the measure impacts and outline the market segment data assumptions utilized for each case in the DBEDT DSM Forecasting models. The variables and figures included in the summary report sheet are described. Numerous tables and figures are included.

1995-04-01

255

Evaluation on the formability of magnesium alloy, AZ31  

Energy Technology Data Exchange (ETDEWEB)

Magnesium is known to have poor formability at room temperature, mainly attributed to its hexagonal lattice structure. This paper presents the findings generated from development of warm forming to produce thin-walled magnesium components. Finite element analysis was conducted to evaluate the formability of the material and the simulated results were compared to the tensile results and product formability. Tensile tests were used to verify the formability of the sheet metal at difference temperatures. The process parameters considered in the feasibility study were forming temperature, in the range of 28 C to 300 C and magnesium sheet (AZ31B-H24) thickness, in the range of 0.4 mm to 1 mm. Magnesium hand phone covers of a thickness down to 0.4 mm have been successfully produced. The feasible forming temperature was found to be between 200 C and 250 C. Metallographic examination shows evident of recrystallisation when the magnesium ...

2003-07-01

256

Effect of Non-aqueous Solvents on the Rate of Production of Copper Powder from Copper Sulphate Solution by Cementation on Stationary Zinc Sheet and Rotating Zinc Cylinder  

Scientific Electronic Library Online (English)

Abstract in english The rate of copper II/zinc cementation from copper sulphate solutions in the absence and in the presence of methanol (CH3OH) and dimethyl sulphoxide (DMSO) has been studied and the reaction was found to follow first-order kinetics. The influence of several parameters on the course of the reaction, such as cylinder rotation speed, initial concentration of Cu2+ ions, temperature and concentration of organic solvent, was investigated. In the case of CH3OH, rotating zinc cyli (more) nder was used, while in the presence of DMSO stationary zinc sheet and rotating zinc cylinder were used. It was found that (1) the percentage inhibition caused by methanol ranged from 10.70 to 58.38 depending on the concentration of the alcohol used; (2) the rate of cementation in the presence of DMSO using rotating zinc cylinder > the rate of cementation in the presence of DMSO using stationary zinc sheet; (3) the rate of cementation on zinc ...

2004-01-01

257

Composite electrode substrate for fuel cell requiring no separator plate and its production method; Separeta ban wo fuyo tosuru nenryo denchiyo fukugo denkyoku kiban oyobi sono seizoho  

Energy Technology Data Exchange (ETDEWEB)

This invention relates to the production method of composite electrode substrate for fuel cell. An impermeable material is used for edge sealant. The sealant is put in the clearance between two electrodes consisting of porous carbon material via thermoplastic resin sheet, and heated while being pressed. This production method increases the adherence between the porous carbon bodies and reduces the contact resistivity at the joint interface. Consequently, it becomes possible to produce the composite electrode for fuel cell without separator, resulting in simplification of assembly work, weight reduction, and downsizing. The preferable porous carbon body is made from shrinkage-treated fiber. After sheet forming, the thermosetting resin is impregnated, and then it is burnt to carbonization. Or mixed sheet of rayon and acrylic fiber is laminated to be heated and pressed without impregnating the resin. The pressed resin is then ...

1996-04-12

258

Advanced concept on high temperature strength based on NRIM creep data sheet; Kinzaigiken kuripu deta shito kara umareta koon kyodo no atarashii toraekat  

Energy Technology Data Exchange (ETDEWEB)

National Research Institute for Materials started in FY1966 a creep data sheet project aiming at obtaining the creep test data until 360Ms (about 11 years and half) in maximum, and has continuously been conducting the above on more than 40 kinds of heat resistant metallic materials for practical use for 30 years already as of January, 1996. The 360Ms creep rupture strength which has been aimed at by this project is the basic important strength property referred to at the time of determining design allowable stress of high temperature structural members. The Institute has published the accumulation of the test data of long range creeps lasting beyond 360Ms of the Institute as a creep data sheet, and in this article, the tremendous volume of this long range creep test data is analyzed and studied systematically, the new knowledge concerning the high temperature strength properties thereby obtained is named the base creep strength concept and ...

1996-05-20

259

A calculation model for thermo-hydraulic analyses of the PGV-1000 steam generator  

International Nuclear Information System (INIS)

A calculation model was developed for the analysis of thermal and hydraulic processes in the PGV-1000 horizontal steam generator. The model makes it possible to examine the hydraulics of the primary medium, i.e., the distribution of flow velocities and mass flows in the exchanger tube system and hydraulic losses of the primary medium in the steam generator during its flow between the two connecting sites to the main circulation pipeline, spatial distribution of heat fluxes between the primary and secondary sides of the steam generator and the total transmitted thermal power, pressure on the secondary side of the generator, natural circulation of the working medium on the secondary side, and the mean circulation number, spatial distribution of the volume fraction of the steam component in the intertubular space, effect of the perforated sheet on the thermo-hydraulic processes in the steam generator, redistribution of the steam component in the compartment above the ...

1994-01-01

260

Temperature Dependent Constitutive Modeling for Magnesium Alloy Sheet  

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are compared.

2010-06-15

261

Quantitation of Cellular Dynamics in Growing Arabidopsis Roots with Light Sheet Microscopy  

CERN Document Server

To understand dynamic developmental processes, living tissues must be imaged frequently and for extended periods of time. Root development is extensively studied at cellular resolution to understand basic mechanisms underlying pattern formation and maintenance in plants. Unfortunately, ensuring continuous specimen access, while preserving physiological conditions and preventing photo-damage, poses major barriers to measurements of cellular dynamics in indeterminately growing organs such as plant roots. We present a system that integrates optical sectioning through light sheet fluorescence microscopy with hydroponic culture that enables us to image at cellular resolution a vertically growing Arabidopsis root every few minutes and for several consecutive days. We describe novel automated routines to track the root tip as it grows, track cellular nuclei and identify cell divisions. We demonstrate the system's capabilities by collecting data on divisions and nuclear ...

2011-01-01

262

Free air flows for the removal of pollutants from car parks. Air-conditioning systems without sheet-metal ducts as an alternative to transverse ventilation with sheet-metal ducts. Pt. 2. Freie Luftstroemungen entsorgen Parkraeume. RLT-Anlagen ohne Blechkanaele als Alternative zur Querlueftung mit Blechkanaelen. T. 2  

Energy Technology Data Exchange (ETDEWEB)

In parking areas of large extent, the removal of engine exhaust gases, especially of their CO gas components with ventilation plant is mainly done by transverse ventilation over short paths. By their presence, the ventilation ducts required for this purpose often reduce the value of the parking space by restrictions with a consequent reduction of their acceptance by the users. Longitudinal ventilation without ducts can be a remedy in such cases. Depending on the required room air quality in the zones of highest loading, the volume flows with longitudinal removal are no greater than with conventional transverse ventilation. This article is concerned with the different methods of operation of the two systems. (orig./BWI)

1994-04-01

263

Forming characteristics of cast magnesium alloy sheets manufactured by roll strip casting process  

Energy Technology Data Exchange (ETDEWEB)

Plastic formability of cast magnesium alloy that were hot rolled after roll strip casting was investigated to ascertain the feasibility of semi-solid strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

2004-07-01

264

Experimental studies and numerical modeling of the specimen and grain size effects on the flow stress of sheet metal in microforming  

British Library Electronic Table of Contents (United Kingdom)

In this research, the interactive effect of grain and specimen sizes on the flow stress of sheet metal in microforming is investigated via the tensile test of pure copper and numerical modeling. Models based on different assumptions are proposed to analyze the size effect phenomenon. It is found that the flow stress decreases linearly with the decrease of the ratio of specimen to grain sizes. The grain boundary thickness decreases and its volume fraction increases with the decrease of grain size. The variation of grain boundary thickness is not proportional to the variation of grain size. Furthermore, the fraction of grain boundary increases with the strain and the ratio of specimen to grain sizes. Based on the FE simulation, it is found that the simulated flow stress, which is modeled bas...

2011-01-01

265

Experimental and analytical study of saturation current density of laser-doped phosphorus emitters for silicon solar cells  

British Library Electronic Table of Contents (United Kingdom)

Heavily doped emitters with low saturation current density are of particular interest for selective emitter solar cells. These emitters can be obtained by laser doping through the phosphosilicate glass layer formed after thermal diffusion from POCl3 gas. The experimental results show that in contrast to purely POCl3 furnace-diffused emitters, the saturation current density of laser-doped emitters does not increase linearly as sheet resistance decreases, but rather features two distinct regimes. In one of these regimes, the saturation current density is found to decrease as the sheet resistance decreases, reaching values lower than those of furnace emitters. This peculiar behaviour was explained by both qualitative analysis and numerical simulations.

2011-01-01

266

Erosive radially-slotted discharge in sheet current mode  

CERN Document Server

New non-stationary non-contracted form of the erosive radially-slotted discharge as a thin round sheet with the current of the azimuth direction have been discovered, its existence beings stipulated by a radial transport-wave fluxes. Characteristic features of this discharge is self-confinement of the discharge current magnitude, corresponding decrease of the current pulse duration and occurrence of an energy and substance ejection with rather unusual properties. Measurements of kinetics of the discharge current, the plasma radiation intensity and an electrical probe signal, as well as the transmission electron microscope investigations of characteristic aerodisperse aggregates arising the erosive phase, have been carried out. The probe signal duration was about 10 times greater than that of the current; its kinetics was complicated suggesting existence in the slot of two components with fundamentally different properties and states of the substance.

2001-01-01

267

Effects of rolling condition on warm deep drawability of magnesium alloy sheets produced by twin-roll strip casting  

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

2005-07-01

268

Characterization of surface defects after flanging of metallic sheets  

British Library Electronic Table of Contents (United Kingdom)

This paper deals with surface defects of automobile outer panels, which alter significantly the vehicle quality. Such defects occur during springback, after forming or flanging steps, and are characterized by concave depression of small amplitude over the convex shape of the part. The aim of this work is to reproduce at the laboratory scale a surface defect that occurs after flanging on a geometry similar to a door upper corner. A dedicated device has been designed in order to generate small size surface defects during flanging of metallic thin sheets. The outer surface of the sample was digitalized and the spatial geometry of the defect was evaluated from curvature change along 2D profiles. This study shows that the flanging height does not influence significantly the surface defect geome...

2011-01-01

269

Calculation of electromagnetic force in electromagnetic forming process of metal sheet  

International Nuclear Information System (INIS)

Electromagnetic forming (EMF) is a forming process that relies on the inductive electromagnetic force to deform metallic workpiece at high speed. Calculation of the electromagnetic force is essential to understand the EMF process. However, accurate calculation requires complex numerical solution, in which the coupling between the electromagnetic process and the deformation of workpiece needs be considered. In this paper, an appropriate formula has been developed to calculate the electromagnetic force in metal work-piece in the sheet EMF process. The effects of the geometric size of coil, the material properties, and the parameters of discharge circuit on electromagnetic force are taken into consideration. Through the formula, the electromagnetic force at different time and in different positions of the workpiece can be predicted. The calculated electromagnetic force and magnetic field are in good agreement with the numerical and experimental results. The accurate ...

2010-06-15

270

Nevada Test Site, 2006 Waste Management Monitoring Report, Area 3 and Area 5 Radioactive Waste Management Sites  

Science.gov (United States)

Environmental monitoring data were collected at and around the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site. These data are associated with radiation exposure, air, groundwater, meteorology, vadose zone, subsidence, and biota. This report summarizes the 2006 environmental data to provide an overall evaluation of RWMS performance and to support environmental compliance and performance assessment (PA) activities. Some of these data (e.g., radiation exposure, air, and groundwater) are presented in other reports (U.S. Department of Energy, 2006; Warren and Grossman, 2007; National Security Technologies, LLC, 2007). Direct radiation monitoring data indicate that exposure levels around the RWMSs are at or below background levels. Air monitoring data at the Area 3 and Area 5 RWMSs indicate that tritium concentrations are slightly above background levels. There is no detectable man-made radioactivity by gamma spectroscopy, and concentrations of americium ...

2007-06-30

271

VIIRS F1 Pre-Launch Calibration d Ch i i and Characterization:  

Science.gov (United States)

0.5% (one sigma) for scan angles less than 55.84 degrees off nadir ... Two polarization sheets and one blocking filter were used .... Polarization factors of different detectors in a given band cross and the cross point ...

272

Thermal performance of solar air collectors with a passive heat transfer augmentation technique  

Energy Technology Data Exchange (ETDEWEB)

One of the main disadvantages of solar air collectors in practical applications is their relatively low efficiency. In this experimental investigation, the shape and arrangement of absorber surfaces of the collectors were reorganized to provide better heat transfer surfaces suitable for the passive heat transfer augmentation techniques. The performance of such solar air collectors with staggered absorber sheets was tested. The experimental results show that it is possible to provide 10 to 25% enhancement in the efficiency compared to the conventional solar air collectors. (authors)

2000-07-01

273

The YTH Domain Is a Novel RNA Binding Domain*  

UK PubMed Central (United Kingdom)

The YTH (YT521-B homology) domain was identified by sequence comparison and is found in 174 different proteins expressed in eukaryotes. It is characterized by 14 invariant residues within an α-helix/β-sheet...Full Text Available

2010-05-07

274

The Sasol route to fuels  

Energy Technology Data Exchange (ETDEWEB)

Details are given of the Sasol operation in South Africa. Flow sheets are provided for Sasol 1 and Sasol 2 and 3. The Sasol 1 plant produces waxes, liquid fuels, pipeline gas and chemicals; the Sasol 2 and 3 plants primarily produce ethylene, gasoline and diesel fuel. The versatility of the process is emphasized. The product selectivities of the fixed bed and Synthol reactors are shown and the properties of the products are compared. The influence of the catalyst on selectivity is examined.

1982-12-01

275

Studies of off-shell amplitudes in string theory  

Energy Technology Data Exchange (ETDEWEB)

Off-shell amplitudes for the open bosonic string and the closed spinning string are considered. Due to the presence of corners on the open string world sheet, strict Weyl invariance is broken. A consistent gauge-fixing procedure to treat this anomaly is described. Factorization of amplitudes with one or two off-shell strings and any number of on-shell tachyons is established. An attempt is made to construct a propagator for the spinning string. The inherent ambiguities in the choice of boundary conditions for the fermionic coordinates are outlined.

1989-01-01

276

State-of-the-art technology for production of seamless tubes in zirconium and titanium alloys  

International Nuclear Information System (INIS)

Zircaloy fabrication plant manufactures all the necessary Zr-2 components like fuel canning tubes, calandria tubes and other rod and sheet products. This plant is having a capacity of producing about 4 lakh nos. of PHWR fuel tubes per annum. These tubes are seamless, thin walled with close dimensional tolerances and stringent mechanical properties. The plant has established all the facilities required to produce these tubes with required quality.

277

Semi-solid twin-roll casting process of magnesium alloy sheets  

International Nuclear Information System (INIS)

An experimental approach has been performed to ascertain the effectiveness of semi-solid strip casting using a horizontal twin roll caster. The demand for light-weight products with high strength has grown recently due to the rapid development of automobile and aircraft technology. One key to such development has been utilization of magnesium alloys, which can potentially reduce the total product weight. However, the problems of utilizing magnesium alloys are still mainly related to high manufacturing cost. One of the solutions to this problem is to develop magnesium casting-rolling technology in order to produce magnesium sheet products at competitive cost for commercial applications. In this experiment, magnesium alloy AZ31B was used to ascertain the effectiveness of semi-solid roll strip casting for producing magnesium alloy sheets. The temperature of the molten magnesium, and the roll speeds of the upper and lower rolls, (which could be ...

2004-06-10

278

Renewable energy technologies for federal facilities: Geothermal heat pump  

Energy Technology Data Exchange (ETDEWEB)

This sheet summarizes information on geothermal heat pumps (GHPs), which extracts heat from the ground in the winter and transfers heat to the ground in the summer. More than 200,000 GHPs are operating in US; they can reduce energy consumption and related emissions by 23 to 44% compared to air-source heat pumps. Opportunities for use of GHPs, requirements, and cost are described. Important terms are defined.

1996-05-01

279

Radon measurements in the interior of the great pyramid  

Energy Technology Data Exchange (ETDEWEB)

Radon concentration measurements were made in the interior of the great pyramid of ''Cheops'' at Giza. Measurements were carried out using CR-39 as a solid state nuclear track detector. The CR-39 sheets were placed inside the Queen's and King's chambers and along the ascending corridor leading to them. An evaluation of the radon concentration is presented and discussed. (author).

1991-01-01

280

Radon measurements in the interior of the great pyramid  

International Nuclear Information System (INIS)

Radon concentration measurements were made in the interior of the great pyramid of ''Cheops'' at Giza. Measurements were carried out using CR-39 as a solid state nuclear track detector. The CR-39 sheets were placed inside the Queen's and King's chambers and along the ascending corridor leading to them. An evaluation of the radon concentration is presented and discussed. (author).

281

Qualitative risk evaluation of environmental restoration programs at Brookhaven National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

This report documents the evaluation of risks associated with environmental restoration activities at Brookhaven National Laboratory using two tools supplied by DOE to provide a consistent set of risk estimates across the DOE complex: Risk Data Sheets (RDS) and Relative Risk Ranking. The tools are described, the process taken characterized, results provided and discussed. The two approaches are compared and recommendations provided for continuing improvement of the process.

1996-05-01

282

Phantom simulation device for scintillation cameras  

Energy Technology Data Exchange (ETDEWEB)

A phantom simulation imaging quality control device is described that effectively simulates one centimeter lesions, using steel ball bearings as gamma ray attenuators. The bearings are mounted in a synthetic resinous sheet in an orthogonal pattern. The phantom can provide uniformity, resolution, linearity, distortion and field size checks, all with a single exposure.

1981-08-25

283

PWR steam generator chemical cleaning process  

International Nuclear Information System (INIS)

Some of the origins of corrosion encountered in the secondary side of pressurized water reactor steam generators are:-sludge accumulation (a mixture of metal oxides, primarily magnetite and copper) on tube sheet and attack of tube support plates by aggressive impurities leading to denting. Although Electricite de France has not suffered from these problems, it has developed a chemical cleaning process to dissolve corrosion products at both locations. (author).

1986-10-13

284

Nuclear Data Sheets for A -- 216, 220, 224, and 228  

International Nuclear Information System (INIS)

Detailed level schemes, decay schemes, and the experimental data on which they are based are presented for all nuclei with mass numbers A -- 216, 220, 224, and 228. The experimental data are evaluated; inconsistencies and discrepancies are noted; and adopted values for level and #gamma#-ray energies, #gamma# intensities, as well as for other nuclear properties are given.

285

In Pursuit of Spreadsheet Excellence  

CERN Document Server

The first fully-documented study into the quantitative impact of errors in operational spreadsheets identified an interesting anomaly. One of the five participating organisations involved in the study contributed a set of five spreadsheets of such quality that they set the organisation apart in a statistical sense. This virtuoso performance gave rise to a simple sampling test - The Clean Sheet Test - which can be used to objectively evaluate if an organisation is in control of the spreadsheets it is using in important processes such as financial reporting.

2008-01-01

286

GNOM-LIKE1/ERMO1 and SEC24a/ERMO2 Are Required for Maintenance of Endoplasmic Reticulum Morphology in Arabidopsis thaliana[W  

UK PubMed Central (United Kingdom)

The endoplasmic reticulum (ER) is composed of tubules, sheets, and three-way junctions, resulting in a highly conserved polygonal network in all eukaryotes. The molecular mechanisms responsible for...Full Text Available

2009-11-01

287

Financial statistics of major US publicly owned electric utilities 1994  

Energy Technology Data Exchange (ETDEWEB)

This publication presents 5 years (1990--94) of summary financial data and current year detailed financial data on the major publicly owned electric utilities. Generator and nongenerator summaries are presented. Composite tables present: Aggregates of income statement and balance sheet data, financial indicators, electric operation and maintenance expenses, electric utility plant, number of consumers, sales of electricity, and operating revenue, and electric energy account data.

1995-12-15

288

Experimental Verification of the Hall Effect during Magnetic Reconnection in a Laboratory Plasma  

Energy Technology Data Exchange (ETDEWEB)

In this letter we report a clear and unambiguous observation of the out-of-plane quadrupole magnetic field suggested by numerical simulations in the reconnecting current sheet in the Magnetic Reconnection Experiment (MRX). Measurements show that the Hall effect is large in collisionless regime and becomes small as the collisionality increases, indicating that the Hall effect plays an important role in collisionless reconnection.

2005-06-16

289

Development of 345-kV capacitive-graded joint. Final report  

Energy Technology Data Exchange (ETDEWEB)

The design of a 345-kV prefabricated capacitive-graded joint for oil-filled cables and the manufacture and testing of prototype joints are described. Tests on prototype No. 4 demonstrated the adequacy of the printed circuit design. It was not possible to consistently obtain high-quality capacitive sheets and substantial effort is required to remedy this problem. Advantages of these prefabricated joints are summarized, and specific recommendations are made for further development of the concept.

1980-09-01

290

Defra Studentship: Biodegradable starch nano-composites for thermoformable film packaging for food products  

Environmental Research Database

DescriptionThe objective is to exploit the use of wheat as an industrial raw material and understand the effect of material variation in wheat starch and flour on final material properties for food packaging applications. The project will focus on property enhancement in terms of stiffness, strength, toughness, moisture barrier resistance, transparency, ageing resistance, microbial stability and biodegradability of starch-based packaging materials made by sheet extrusion and thermoforming processes, in ord [continued...

2008-01-31

291

Cultured epidermal allografts as biological wound dressings.  

Science.gov (United States)

Recent advances in cell culture technology permit the generation of large stratified epithelial sheets appropriate for wound coverage. Autografts (sheets prepared from the patient's own skin) have proven life-saving in the treatment of large third-degree burns and have been successfully employed in the management of chronic ulcers. Allografts (sheets prepared from the skin of an unrelated donor) have also been used. In our experience, cultured allografts derived from neonatal foreskin provide a potent stimulus to healing in a variety of partial thickness wounds. Their application is a simple outpatient procedure which involves no discomfort for the patient. In contrast to autografting, no biopsy is necessary and use of cultured allogenic cells permits immediate grafts availability and possibility of stockpiling and preserving grafts for future use. Preparation of epithelial sheets suitable for grafting ...

1991-01-01

292

Comments dataset for A=177.  

Energy Technology Data Exchange (ETDEWEB)

Evaluated nuclear structure and decay data for all nuclei within the A=177 mass chain are presented. Significant new information is included since the previous evaluation of this mass chain. The present work supersedes the earlier one by E. Browne (1993Br06), published in Nuclear Data Sheets 68, 747 (1993).

2003-04-01

293

Calculation method of elastic moduli of textured two-phase titanium alloys  

International Nuclear Information System (INIS)

On the basis of symmetry way of texture description a calculation method of elastic moduli of two-phase titanium alloys with rolling texture has been suggested. Efficiency of the calculation formulas is checked by comparing the calculation results of Young modulus anisotropy in the sheet plane of (#alpha#+#beta#)-titanium alloy VT23 with the experimental data.

294

CORONAL OBSERVATIONS OF CMEs Report of Working Group A  

Science.gov (United States)

imaging of the solar corona began in 1960 via a primitive pinhole camera on a ... IR wavelengths. Such data help us to study in detail the pre-eruptive ...... Schematic picture of flare loops, CME, and the current sheet between ..... As part of NASA's Living With a Star (LWS) program the planned Sentinel mission ...

295

Influence of solar activity and environment on 10Be in recent natural archives  

Energy Technology Data Exchange (ETDEWEB)

Understanding the link between the Sun and climate is vital in the current incidence of global climate change, and 10Be in natural archives constitutes an excellent tracer for this purpose. As cosmic rays enter the atmosphere, cosmogenic isotopes like 10Be and 14C are formed. Variations in solar activity modulate the amount of incoming cosmic rays, and thereby cosmogenic isotope production. Atmospherically produced 10Be enters natural archives such as sediments and glaciers by wet and dry deposition within about a year of production. 10Be from natural archives therefore provides information on past solar activity, and because these archives also contain climate information, solar activity and climate can be linked. One remaining question is to what degree 10Be in natural archives reflects production, and to what extent the local and regional environment overprints the production signal. To explore this, 10Be was measured at annual resolution over the last 600 years in a Greenland ...

2009-05-15

296

Water consumption of a six-year-old river red gum plantation in the Southern Zagros Mountains, Iran  

British Library Electronic Table of Contents (United Kingdom)

Water is the most important limiting factor in the development of arid environments; therefore, optimization of water use is a necessity in desert reclamation projects. Evapotranspiration of a 6-year-old river red gum (Eucalyptus camaldulensis Dehnh.) plantation, located in a sedimentation basin of an artificial recharge of the Gareh Bygone Plain groundwater system in Iran?s southern Zagros Mountains, was studied during a 7-month period. A neutron moisture probe was used to monitor soil water changes in the root zone. Soil water depletion following rapid drainage for blocks receiving relatively high, medium and low volumes of floodwater were 809.6, 312.4, and 203.1 mm, respectively, for a 150-day period. Soil water potential during most of the study period was below ?1.5 MPa. This study pr...

2007-01-01

297

The development of open-pore multi-layer systems for steam turbines operating with 700 C technology; Die Entwicklung offenporoeser Mehrschichtsysteme fuer Dampfturbinen der 700 C-Technologie  

Energy Technology Data Exchange (ETDEWEB)

In the context of the special research area 561 (Thermally highly loaded, open-porous and cooled multi-layer systems for combined-cycle power stations), the actual technical and scientific realizations are to be extended and new scientific bases are to be created in order to realize total efficiencies of 65 %. In addition, innovative material solutions and new concepts must be compiled for the cooling and drainage. Under this aspect, the author of the contribution under consideration reports on the development of open-porous multi-layer systems for steam turbines of the 700 C technology. It results an efficiency potential of 12 % and a potential of 15 % with the reduction of CO{sub 2} in relation to the actual state of the art. Thereby, the potential of future combined-cycle power stations is not yet exhausted.

2008-07-01

298

Shallow groundwater nitrogen and denitrification in a newly afforested, subirrigated riparian buffer  

British Library Electronic Table of Contents (United Kingdom)

Summary 1. The EU -Nitrates Directive- (Directive 91/676/EEC) and the WFD (Water Framework Directive 2000/60/EEC) introduced a series of measures designed to reduce and prevent water pollution caused or induced by nitrates from agricultural sources. Therefore, there is an urgent requirement to control the nitrate concentration in freshwater. The objective of this paper was to verify the potential capacity of a specifically designed afforested riparian zone in removing the excess of nitrogen from river water. 2. A buffer zone was set with irrigation ditches, to produce a subsurface water flow carrying water from the study river through the buffer strip to drainage ditches. This experimental system enables the co-occurrence of two main processes: vegetation/microbial nitrogen uptake and deni...

2011-01-01

299

Satellite-based estimates of groundwater storage variations in large drainage basins with extensive floodplains  

British Library Electronic Table of Contents (United Kingdom)

This study presents monthly estimates of groundwater anomalies in a large river basin dominated by extensive floodplains, the Negro River Basin, based on the synergistic analysis using multisatellite observations and hydrological models. For the period 2003-2004, changes in water stored in the aquifer is isolated from the total water storage measured by GRACE by removing contributions of both the surface reservoir, derived from satellite imagery and radar altimetry, and the root zone reservoir simulated by WGHM and LaD hydrological models. The groundwater anomalies show a realistic spatial pattern compared with the hydrogeological map of the basin, and similar temporal variations to local in situ groundwater observations and altimetry-derived level height measurements. Results highlight th...

2011-01-01

300

Restauration of the Clinton site; Restauration du site Clinton  

Energy Technology Data Exchange (ETDEWEB)

Mining of copper and zinc took place at the Clinton Mine located in the Estrie region of Quebec between 1973 and 1975, during which time 115,000 tons of mineral were treated at the Solbec plant. In this poster presentation, the authors provided the background information pertaining to this mine and described the state in which it was in 1994. The pit was covered with good quality water, with a pH of 7,1 and copper and zinc content ranging between 0,1 and 0,6 mg/l, and iron ranging between 0,2 and 1,8 mg/l. The tailings basin drainage was found to have a pH of between 3,6 and 6,1. A program for the characterization of the site was implemented and the concept for the restauration of the Clinton site was developed and implemented. The work carried out at the site is discussed during this presentation as well as the monitoring taking place. 27 figs.

2000-07-01

301

Radiation therapy in the treatment of hilar cholangiocarcinoma  

International Nuclear Information System (INIS)

The incidence of hilar cholangiocarcinoma is very rare worldwide. Radical resection is the only prognostic factor for long survival in patients with hilar cholangiocarcinoma. Postoperative radiation therapy can improve local control and survival rates for patients with palliative resection, but it remains controversial in patients with radical resection. Biliary drainage can effectively release bile duct obstruction for the majority of patients with locally advanced disease, and may even prolong survival when combined with radiation therapy. Radiation therapy includes extrernal beam therapy alone, external beam therapy with intraluminal brachytheapy and new radiation technique, such as three dimentional conformal therapy and intensity modulated radiation therapy. The propective randomized clinical study is needed for further investigation in the role of combined modality therapy especially for hilar cholangiocarcinoma. (authors)

2007-10-01

302

New stratigraphic markers in the late Pleistocene Palouse loess: novel fossil gastropods, absolute age constraints and non-aeolian facies  

British Library Electronic Table of Contents (United Kingdom)

Abstract Four stratigraphic sections in the southern part of the Columbia Basin preserve a sequence of aeolian and non-aeolian sediments ranging in age from 943 to >470 14C ka based on accelerator mass spectrometry radiocarbon dating of fossil molluscs, geochemistry of Cascade Mountain-sourced tephra and association with formally recognized pedostratigraphic units (the Washtucna and Old Maid Coulee soils). Study sections are interpreted as representing concurrent deposition of loess and distal Missoula Flood rhythmites in valleys tributary to main drainages backflooded during the Missoula Floods, and formation of carbonate and iron-rich soils. Sediments belong to the formally recognized L-1 and L-2 loess units established for the Palouse loess, which were deposited in the Columbia Basin su...

2010-01-01

303

Monitoring of the environment in mining areas with the use of hyperspectral remote sensing data; Umweltueberwachung in Bergbaugebieten unter Nutzung hyperspektraler Fernerkundungsdaten  

Energy Technology Data Exchange (ETDEWEB)

Within the framework of the MINEO research project assisted by the European Union the Deutsche Steinkohle AG (DSK) has developed methods for the operational use of remote sensing data and geo-information systems for the regular observation, measurement and evaluation of environmental effects in mining areas. Only indirect environmental effects of the mining industry, which may result in particular from subsidence-induced changes in the hydrological situation (ground water level, drainage) and the resulting effects on the vegetation and land utilisation, can be observed for the DSK test area 'Kirchheller Heide' because of the underground mine workings. Hence the evaluations of the remote sensing data were concentrated on the development of methods to measure and analyse the vegetation condition and any changes. MINEO thus constitutes a module for the DSK environmental information system. (orig.)

2005-10-20

304

Mapping soil organic matter using the topographic wetness index: A comparative study based on different flow-direction algorithms and kriging methods  

British Library Electronic Table of Contents (United Kingdom)

Terrain attributes derived from digital elevation models have been used widely for mapping soil organic matter (SOM). Among these attributes, the topographic wetness index (TWI), an index for quantitatively indicating the balance between water accumulation and drainage conditions at the local scale, has been shown to correlate with SOM. However, TWIs used in most studies are calculated using a single-flow-direction (SFD) algorithm, which assumes that all water from a grid cell flows into only one neighboring cell. This assumption is not always valid, especially in areas with low relief where movement of water may be divergent. To overcome this SFD limitation, a multiple-flow-direction (MFD) algorithm has been developed, which distributes flow from a grid cell to several downslope neighbors...

2010-01-01

305

Impact of the regulation on information about new substances derived from the Canadian Environmental Protection Act (CEPA) on the application of biotechnological treatment of AMD : a case study; Impact du reglement sur les renseignements concernant les substances nouvelles de la LCPE sur l'application d'une biotechnologie de traitement du DMA : etude de cas  

Energy Technology Data Exchange (ETDEWEB)

This poster presentation covered a number of issues related to the new regulations concerning information on new substances derived from the Canadian Environmental Protection Act (CEPA). The authors described the background, and the objectives of the research project. A brief overview of the Acid Mine Drainage (AMD) process was provided, as well as the sulphate reduction process. The general methodology was explained, and the results of the bioactivation presented. The process followed for the bioaugmentation and the results obtained were presented. The regulations concerning information on new substances derived from the CEPA were described. The authors then presented their conclusions and perspectives. 26 figs.

2000-07-01

306

Economic evaluation of horizontal borehole drilling for methane drainage from coalbeds. Information Circular/1986  

Energy Technology Data Exchange (ETDEWEB)

The potential profitability of a horizontal borehole drilling program for recovering methane gas in an Alabama coalbed for 6 yr in advance of mining is estimated in the Bureau of Mines report. A cash flow analysis based on estimated capital investments, annual operating costs, and the selling price of methane gas was used to determine the net income and net cash flow for each year of operation. Subsequently, the annual net cash flows were capitalized to determine the discounted cash flow rate of return. Findings indicate that a 25.08-percent interest rate of return on investment could be realized from the sale of methane gas in excess of 3 billion cubic feet during the years 1985 through 1990 at a minesite price of $2.25/per thousand cubic feet.

1986-01-01

307

Development document for proposed effluent limitations guidelines and standards for the coastal subcategory of the oil and gas extraction point source category  

Science.gov (United States)

;Table of Contents: Legal authority; Summary of proposed regulations; Industry definition and waste streams; Industry description; Data and information gathering; Selection of pollutant parameters; Drilling wastes-characterization, control, and treatment technologies; Produced water-characterization, control, and treatment technologies; Miscellaneous waste-characterization, control, and treatment technologies; Cost and pollutant loading determination of drilling fluids and drill cuttings; Compliance cost and pollutant load determination of produced water; Compliance cost and pollutant load determination of well treatment, workover, and completion fluids; Cost and pollutant loading determination of deck drainage; Options selection-rationale and total costs; Pretreatment standards; Non-water quality environmental impacts and other factors; Best Management Practices; and Appendices.

1995-02-01

308

Curative resection of a huge malignant pancreatic endocrine tumor by pancreatoduodenectomy with portal and superior mesenteric vein resection and reconstruction using the right ovarian vein: Report of a case  

British Library Electronic Table of Contents (United Kingdom)

Nonfunctioning pancreatic endocrine tumors (PETs) are rare and generally asymptomatic. A 68-year-old woman who had refused treatment for a pancreatic mass, revealed by ultrasonography to be 55 mm in diameter, was referred to us again 29 months later with jaundice. Investigations showed an 82-mm tumor in the head of pancreas, exposed from the papilla of Vater to the duodenal lumen. After biliary decompression and drainage, we performed pancreatoduodenectomy with resection of the portal vein and superior mesenteric vein, followed by reconstruction using a cylindrically customized autologous graft harvested from the right ovarian vein. The tumor was resected curatively. Microscopically, it consisted of trabecular and ribbon-like arrangement of neoplastic cells. Immunohistochemical staining wa...

2011-01-01

309

Chemoradiotherapy of unresectable and recurrent cholangiocarcinoma  

International Nuclear Information System (INIS)

This study is for chemoradiotherapy of unresectable and recurrent cholangiocarcinoma (CCC). Between April 2005 and March 2007, 5 patients were evaluated for unresectable and recurrent CCC. All patients were performed percutaneous transhepatic biliary drainage (PTBD) and treated with chemoradiotherapy. The radiation method was an external beam radiotherapy (EBRT) and remote after loading system (RALS). The chemotherapy was 5-fluorouracil (FU) and gemcitabine by intravenous injection. Three patients had unresectable and 2 had recurrent CCC. As for the side effects, 4 patients had a slight neutropenia and 1 had an uncontrollable gastric bleeding. No patient had cholangitis. The mean survival time for unresectable and recurrent CCC was 13.7 months and 17 months, respectively. Our results indicated that chemoradiotherapy had been consistent with efficacy in patients with unresectable and recurrent CCC. (author)

2007-11-01

310

Bumper zone at the Aldermac mine tailing site : study of certain remediation techniques; Zones d'epanchement du parc a residus miniers Aldermac : etude de certaines techniques de rehabilitation  

Energy Technology Data Exchange (ETDEWEB)

Acid mine drainage is probably the most important problem facing the mining industry. In this study, the authors evaluated different techniques for the remediation of mine tailings. An in situ characterization of the Aldermac mine tailings was conducted and the results were presented in this poster presentation. The site characterization was performed to determine the extent of the contamination, and sampling of soils was also performed for laboratory experiments in soil covers. The authors described the methodology followed in the laboratory experiments. Chemical analysis of the leaching water was performed to determine its composition in metals. Microbiological analysis was also conducted, as well as the determination of the water saturation index. The authors indicated that they will analyze the results further. tabs., 12 figs.

2000-07-01

311

Analyses and monitoring of lignite mining lakes in Eastern Germany with spectral signatures of Landsat TM satellite data  

British Library Electronic Table of Contents (United Kingdom)

Coal mining activities cause an increased acidity and an associated decrease of the pH-value in mine waters. This process is also known as acid mine drainage (AMD). Due to AMD, lakes that were formed in the post mining landscapes in the lignite mining area of Central Germany are characterized by specific limnological development changes. Remote sensing is a time and cost saving technique that enables the observation of the hydrological and limnological development of the lakes ranging from a small to a mid size scale. The current research was based on Landsat TM5/ETM+7 satellite data collected between 1999 and 2004. In combination of satellite data, surface waters of the post mining lakes in Central Germany were sampled and analyzed for their physicochemical properties. The objective of th...

2011-01-01

312

Agriculture as a source of phosphorus for eutrophication in southern Europe  

British Library Electronic Table of Contents (United Kingdom)

Abstract Large areas of the southern European countries possess a Mediterranean climate, which influences soil properties, land use, fertilizer application practices and pathways of phosphorus (P) loss from agricultural soils. On average, inputs of fertilizer P exceed P exports from the agricultural areas in these countries; however, large differences in P surplus/deficit and soil P test values exist among regions. Losses of P in drainage water are modest except in some irrigated areas and in those regions where intensive animal production is concentrated. Losses of P in runoff water, whether as dissolved reactive or particulate P, can be substantial as a result of the significance of erosive processes under the land uses typical of the Mediterranean region, where extreme rainfall events c...

2007-01-01

313

A new method for creating maps of artificially drained areas in large river basins based on aerial photographs and geodata  

British Library Electronic Table of Contents (United Kingdom)

With regard to the creation of river basin plans and programmes of measures according to the EU Water Framework Directive, the importance of model-supported analyses of nutrient inputs into aquatic systems and the localization of source areas is increasing. Especially in lowland regions artificial drainage installations play a major role, but little information exists concerning their location within larger river basins. Therefore, artificially drained lands were identified by interpreting aerial photographs and typical site conditions of the drained plots were derived. A GIS-based approach was then developed, which allows the delineation of artificially drained lands by combining various site conditions like soil properties and land use type. After checking the validity of a derived map f...

2009-01-01

314

Study on adsorption of methanol onto carbon based adsorbents  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the isothermal characteristics of methanol onto two specimens of activated carbons namely Maxsorb III and Tsurumi activated charcoal. Dubinin Raduskevich (D-R) equation is used to correlate the adsorption isotherms and to form the pressure-temperature-concentration diagram for both of the assorted pairs. Experimental results show that the maximum adsorption capacity of Maxsorb III/methanol pair is 1.76 times that of activated charcoal/methanol pair. Employing a time-independent mathematical model, the performance of adsorption cooling cycle using Maxsorb III/methanol and activated charcoal/methanol pairs has been studied and compared with that of three other types of carbon based adsorbent/methanol pairs. Theoretical calculations show the superiority of Maxsorb III/methanol pair for both of air-conditioning and ice-making applications. (author)

2009-11-15

315

Structural analysis and stress evaluation system for steel structures: ADAMS  

Energy Technology Data Exchange (ETDEWEB)

In order to perform the structural analysis and stress evaluation for frame structures in the nuclear power plants, ADAMS (AIJ Design Analysis and Modules System) has been developed by the addition of the following functions to the ICES-STRUDL system. 1. Load combination and stress evaluation on the basis of specifications for designing steel structure (issued by the Architecture Institute of Japan). 2. Combination of load and stress evaluation of piping support on the basis of the regulations of Ministry of International Trade and Industry. 3. Addition of other functions than that described above. ADAMS enables structural analysis and stress evaluation exactly and efficiently not only for a large scale structure such as the pipe whip protection structure installed inside of the primary containment vessel for many loading cases but also for a large number of structures such as piping support. This system can be applied not only to nuclear power plant but also other ...

1980-11-01

316

Stoichio-kinetic modeling and optimization of chemical synthesis: Application to the aldolic condensation of furfural on acetone  

British Library Electronic Table of Contents (United Kingdom)

The condensation reaction of furfural (F) on acetone (Ac) gives a high added value product, the 4-(2-furyl)-3-buten-2-one (FAc), used as aroma in alcohol free drinks, ice, candies, gelatines and other products of current life. This synthesis valorises the residues of sugar cane treatment since furfural is obtained by hydrolysis of sugar cane bagasse followed by vapor training extraction. In the face of numerous and complex reactions involved in this synthesis, it is very complicated to define the kinetic laws from exact stoichiometry. A solution allowing to cope the problem consists in identifying an appropriate stoichiometric model. It does not attempt to represent exactly all the reaction mechanisms, but proposes a mathematical support to integrate available knowledge on the transformati...

2008-01-01

317

Spatial and seasonal variability in cetacean distribution in the fjords of northern Patagonia, Chile  

British Library Electronic Table of Contents (United Kingdom)

Viddi, F. A., Hucke-Gaete, R., Torres-Florez, J. P., and Ribeiro, S. 2010. Spatial and seasonal variability in cetacean distribution in the fjords of northern Patagonia, Chile. - ICES Journal of Marine Science, 67: 959-970. Compared with other Chilean coastal areas, little is known about the diversity and distribution of cetaceans in northern Patagonian fjords. Between December 2000 and November 2001, surveys on platforms of opportunity were undertaken in southern Chile to evaluate species richness and the spatial and seasonal distribution of cetaceans. Nine species were recorded, blue, humpback, and minke whales, Peales dolphin, Chilean dolphin, killer whale, false killer whale, bottlenose dolphin, and Cuviers beaked whale. The pattern of cetacean distribution displayed significant season...

2010-01-01

318

Results from Amanda  

Energy Technology Data Exchange (ETDEWEB)

In this report we present an update on the results from the Amanda-B10 detector which operated in 1997 at depths of 1500 to 2000 meters in the deep Antarctic ice. The goal of Amanda project is to search for extra-terrestrial neutrinos. As a precursor to such a search we have studied atmospheric neutrinos which act as a calibration source for the detector. The observation of atmospheric neutrinos at a rate consistent with Monte-Carlo predictions establishes Amanda-B10 as a neutrino telescope. The Amanda-B10 data has been searched for evidence of several classes of neutrinos and for magnetic monopoles. Searches for a diffuse high energy neutrino flux and for neutrinos in coincidence with gamma-ray bursts have been conducted. Preliminary data analyses show no excess of neutrinos has been found. (A.C.)

2001-07-01

319

Radius of thawing around an injection well and time of complete freezeback  

Science.gov (United States)

An approximate method of calculating the radius of thawing around an injection well is presented. The method is based on the assumption that for a cylindrical system the position of the phase interface in the Stefan problem can be approximated through two functions: one function determines the position of the melting-temperature isotherm in the problem without phase transitions and the second function does not depend on time. The adjusted heating time concept was used to describe the first function. The second function is a known analytical relationship and is expressed in terms of ice content, thermal properties of thawed/frozen formations, formation temperature and the temperature of the injected fluid. Simple approximate formulae are suggested to estimate the duration of the freezeback period. To verify the proposed formulae, the results of numerical solutions were used. An example which shows that the duration of the 'safety period' (free from freezing of water ...

2006-06-01

320

Prospects for plug-in hybrid electric vehicles in the United States and Japan: A general equilibrium analysis  

British Library Electronic Table of Contents (United Kingdom)

The plug-in hybrid electric vehicle (PHEV) may offer a potential near term, low-carbon alternative to today's gasoline- and diesel-powered vehicles. A representative vehicle technology that runs on electricity in addition to conventional fuels was introduced into the MIT Emissions Prediction and Policy Analysis (EPPA) model as a perfect substitute for internal combustion engine (ICE-only) vehicles in two likely early-adopting markets, the United States and Japan. We investigate the effect of relative vehicle cost and all-electric range on the timing of PHEV market entry in the presence and absence of an advanced cellulosic biofuels technology and a strong (450ppm) economy-wide carbon constraint. Vehicle cost could be a significant barrier to PHEV entry unless fairly aggressive goals for re...

2010-01-01

321

Cryo-irradiation as a terminal method for the sterilization of drug aqueous solutions  

British Library Electronic Table of Contents (United Kingdom)

The aim of this study is to evaluate the specificities of the irradiation of drugs in frozen aqueous solution. The structures of the degradation products were determined to gain insight into the radiolysis mechanisms occurring in frozen aqueous solutions. Metoclopramide hydrochloride and metoprolol tartrate were chosen as models. The frozen solutions were irradiated at dry ice temperature by high energy electrons at various doses. The drug purity (chemical potency) and the radiolysis products were quantified by HPLC-DAD. Characterization of the degradation products was performed by LC-APCI-MS-MS. The structures of the radiolysis products detected in irradiated frozen aqueous solutions were compared to those detected in solid-state and aqueous solutions (previous studies). For both metoclop...

2008-01-01

322

Air conditioning in high rise buildings; Conditionnement d'air dans les immeubles de grande hauteur  

Energy Technology Data Exchange (ETDEWEB)

This two-tomes book brings together the 108 presentations given at the first conference of the international institute of refrigeration (IIF/IIR) about air conditioning in high rise office buildings. The main themes are: general design and control systems, including split systems, radiant panels, fluctuating and gravity ventilation etc..; energy consumption, optimization and heat recovery; cold storage for peak shaving, including ice slurry circulation; indoor air quality; fire and smokes protection, protection against chimney effects and lighting spots; use of fuzzy logic and of neural networks. It includes also a description of the high rise building situation and works in progress in China, Japan and in some other countries. (J.S.)

1997-07-01

323

AMANDA: Selected physics results  

International Nuclear Information System (INIS)

Since the commissioning of the first 10 strings of the AMANDA neutrino telescope, more than nine years of data has been collected. The proof of principle of high-energy neutrino detection in ice is established. No positive signal of an extra-terrestrial high-energy neutrino flux have been found so far. However, the most stringent upper limits to the flux of cosmic neutrinos-respectively, diffuse, point like or associated with gamma-ray bursts-have been presented. A sample of 3329 up-going muon tracks, representing the largest statistics ever of high-energy neutrino induced events, has been collected between 2000 and 2003. A coincidence of neutrino with an anomalous high-energy gamma-ray flare has been observed from the direction of the Blazar 1ES1959+650-although the observation were not conclusive. Selected results of data taken with the AMANDA detector are here reported.

2006-11-15

324

A future of floods?; Droht Land unter?  

Energy Technology Data Exchange (ETDEWEB)

There are alarming scenarios that state that global heating caused by anthropogenic gaseous emissions will melt the ice caps of Greenland and the Antarctic. This would cause flooding of coastal regions on a global scale. The floods are expected already in the next century, but there are no realistic assessments of the extent of the danger. (orig.) [Deutsch] Alarmierenden Szenarien zufolge koennten durch eine globale Erwaermung, die der Mensch mit dem Ausstoss von Treibhausgasen in die Atmosphaere verursacht, die Eiskappen auf der Antarktis und Groenland abschmelzen. Schon im kommenden Jahrhundert wuerden dadurch weite kuestennahe Gebiete ueberflutet. Noch aber laesst sich schwer abschaetzen, wie real die Gefahr ist. (orig.)

1997-06-01

325

1,800 Years of abrupt climate change, severe fire, and accelerated erosion, Sierra Nevada, California, USA  

British Library Electronic Table of Contents (United Kingdom)

This paper provides both a detailed history of environmental change in the Sierra Nevada over the past 1,800?years and evidence for climate teleconnections between the Sierra Nevada and Greenland during the late Holocene. A review of Greenland ice core data suggests that the magnitudes of abrupt changes in temperature and precipitation increased beginning c. 3,700 and 3,000?years ago, respectively. Precipitation increased abruptly 1,300?years ago. Comparing paleotemperature data from Cirque Peak, CA with paleoprecipitation data from Pyramid Lake, NV suggests that hot temperatures occurred at the beginnings of most severe droughts in the Sierra Nevada over the past 1,800?years. Severe fires and erosion also occurred at Coburn Lake, CA at the beginning of all severe droughts in the Sierra Ne...

2011-01-01

326

Treatment of Malignant Biliary Obstruction with a PTFE-Covered Self-Expandable Nitinol Stent  

Energy Technology Data Exchange (ETDEWEB)

We wanted to determine the technical and clinical efficacy of using a PTFE-covered self-expandable nitinol stent for the palliative treatment of malignant biliary obstruction. Thirty-seven patients with common bile duct strictures caused by malignant disease were treated by placing a total of 37 nitinol PTFE stents. These stents were covered with PTFE with the exception of the last 5 mm at each end; the stent had an unconstrained diameter of 10 mm and a total length of 50 80 mm. The patient survival rate and stent patency rate were calculated by performing Kaplan-Meier survival analysis. The bilirubin, serum amylase and lipase levels before and after stent placement were measured and then compared using a Wilcoxon signed-rank test. The average follow-up duration was 27.9 weeks (range: 2 81 weeks). Placement was successful in all cases. Seventy-six percent of the patients (28/37) experienced adequate palliative drainage for the remainder of their lives. There were ...

2007-10-15

327

Three-phase flow in heterogeneous wettability porous media; Deplacements triphasiques en milieux poreux de mouillabilite heterogene  

Energy Technology Data Exchange (ETDEWEB)

Better understanding and modelling of three-phase flow through porous media is of great interest, especially for improved oil recovery methods such as gas injection processes. Early theoretical and experimental studies have already demonstrated that the wettability characteristics of the solid surface and the spreading characteristics of the fluid system hold the key roles. This observation is confirmed by our theoretical results using DLP theory on the stability and the thickness of static oil films. In most of the works related to three-phase flow processes, homogeneous wettability is assumed. There exist only a few studies demonstrating the tremendous impact of the wettability heterogeneities on gas injection. The objective of the present work is twofold: to demonstrate the effect of small scale wettability heterogeneities on gas injection efficiency, and to develop a tool to predict this impact for various patterns and spatial distributions. To this end an experimental ...

1998-11-26

328

Stent insertion in patients with malignant biliary obstruction: problems of the Hanaro stent  

Energy Technology Data Exchange (ETDEWEB)

To investigate the problems of the Hanaro stent (Solco Intermed, Seoul, Korea) when used in the palliative treatment of patients with inoperable malignant biliary obstruction. Between January 2000 and May 2001, the treatment of 46 patients with malignant biliary obstruction involved percutaneous placement of the Hanaro stent. Five patients encountered problems during removal of the stent's introduction system. The causes of obstruction were pancreatic carcinoma (n=2), cholangiocarcinoma (n=2), and gastric carcinoma with biliary invasion (n=1). In one patient, percutaneous transhepatic cholangiography and stent insertion were performed as a one-step procedure, while the others underwent conventional percutaneous transhepatic biliary drainage for at least two days prior to stent insertion. A self-expandable Hanaro stent, 8-10 mm in deameter and 50-100 mm in lengh, and made from a strand of nitinol wire, was used in all cases. Among the five patients who ...

2002-07-01

329

Radiological characterization of the GRR-1 pool  

International Nuclear Information System (INIS)

GRR-1 is a 5MW open pool type research reactor with MTR-type fuel elements cooled and moderated by light water with beryllium reflectors at the two opposing sides of the core. A graphite thermal neutron column is adjusted to one side of the core. Six radial horizontal beam tubes are available, of which three contain in-pile collimators for neutron scattering instruments. The reactor is currently out of operation for inspection and refurbishment purposes. The core has been dismantled and the fuel elements are stored in the used fuel storage tank. The GRR-1 inspection and refurbishment plan involves inspection and eventually replacement of the reactor's primary cooling circuit. The health physics procedures to be implemented during inspection of the main water outlet are divided in three stages: a) pool dose rate survey from pool top, b) pool drainage by decreasing water level in steps and c) inspection of the water main outlet. urpose of the present work is the ...

2007-11-05

330

Net ecosystem CO{sub 2} exchange of a cutover peatland rehabilitated with a transplanted acrotelm  

Energy Technology Data Exchange (ETDEWEB)

Peatlands are an important long-term sink for atmospheric carbon dioxide (CO{sub 2}). The storage function of peatland ecosystems is significantly impacted by drainage and extraction processes, which can result in the release of significant amounts of CO{sub 2}. This paper investigated the net ecosystem CO{sub 2} exchange of a newly developed extraction-restoration technique that preserved the acrotelm and replaced it directly on the cut surface of the peatlands. The technique used a modified block-cut method with a back-hoe to create a drainage ditch. Actrotelm and surface vegetation were removed and placed to one side, and the peat was mechanically removed. The acrotelm was then transplanted over the older and more decomposed catotelm peat to create a trench topography in which the natural peatland was higher than the extracted zone. Air temperatures, water table levels, and volumetric moisture content levels were measured throughout the ...

2008-07-01

331

Mining activity in Estrie and its environmental legacy; L'activite miniere en Estrie et son heritage environnemental  

Energy Technology Data Exchange (ETDEWEB)

The mining complex Eustis-Capelton, located in the Estrie, was created in 1860, just as the demand and the prices for copper were beginning to rise. It survived the economic crash that followed the end of the American Civil War and continued its activities. Mine Albert was closed in 1907, and the Capelton chemical complex in 1924. As for the Eustis Mine, it continued to operate until 1939. The various mining companies operating in the region were able to maintain their presence throughout the difficult periods due to their flexibility, their capacity to innovate and their good management practices. It was the lack of minerals and several other factors that finally contributed to the demise of the mining industry in the Estrie region. The waste rock piles and tailings at the Eustis, Albert, Capel, and Hartford Mines all display acid mine drainage potential. The tailings are located along the Eustis and Capel streams, which follow a steep course toward the Massawippi ...

2000-07-01

332

Effects of acid mine drainage on a headwater stream ecosystem in Colorado  

International Nuclear Information System (INIS)

The ecological effects of acid mine drainage were investigated during the summer of 1993 on St. Kevin Gulch, a headwater stream near Leadville, Colorado. The stream currently receives acidic water from an abandoned mine. The pH downstream of the mine is between 3.5 and 4.5, and several metals exceed concentrations toxic to aquatic organisms. Zinc is present at especially high concentrations (1 to 10 mg/L) Furthermore, the stream bottom is covered with a thick layer of iron hydroxide precipitates. Effects on stream biota have been dramatic. Aquatic flora in the affected reach is limited to a green filamentous alga, Ulothrix subtilissima. Macroinvertebrate densities are significantly lower in the affected reach (mean = 99 indiv/m"2; SD = 88 indiv/M"2) compared to an upstream (pristine) reference reach (mean = 1,735 indiv/m"2; SD = 652 indiv/M"2). Functional processes were also studied in the stream. Net primary production (NPP) was measured during midday with ...

333

Diffusive and convective transport of radon through cracks in the building understructure  

International Nuclear Information System (INIS)

The objective of this paper is to present a theoretical evaluation of soil and house related factors that may affect the transport of radon from the soil into houses. A two-dimensional mathematical model was used to simulate the diffusive and convective transport of radon into the house through idealized openings in the understructure. With the help of model predictions we tried to find out whether diffusion or convection predominates and under which circumstances. Radon transport through cracks in the house understructure is influenced mainly by the soil permeability, radon concentration at the soil-crack interface, the total area of cracks and the pressure difference across cracks. Because of its large range of variability, the soil permeability appears to have the greatest effect on the radon transport through cracks. At permeabilities below 1x10"-"1"2 m"2 diffusive transport predominates and is almost invariable with the soil permeability. For permeabilities between 1x10"-"1"2 m"2 ...

2000-10-14

334

Acid mine drainage and its impact in the Black Creek watershed, Virginia  

International Nuclear Information System (INIS)

A one-year study was conducted to determine the impacts of acid min drainage (AMD) on the Black Creek watershed in Wise County, Virginia. Water quality, metal content of sediment and water column, soil pH, macroinvertebrate assemblages, habitat assessment and toxicity testing were used to assess the impact in the watershed. A total of 22 sites in the creek and surrounding watershed were actively monitored. This included six primary sources of AMD. Conductivity measurements > 1,000 microhmos/cm were found at eight sites and pH was consistently below 6.0 at seven. Of six metals analyzed, magnesium was highest in the water column, ranging from 16.5 mg/L to 130 mg/L. Aluminum and iron were both elevated in the sediment with iron concentrations as high as 176,000 mg/kg. An increase in sediment metal concentrations was noted when progressing downstream in the creek. Of nine high wall and spoils areas sampled, soil pH was acidic in eight sites, ranging from 5.5 to 3.1. ...

1996-11-17

335

Terra Nova tow-out poised as next East Coast event  

Energy Technology Data Exchange (ETDEWEB)

This spring, Newfoundland will send off a floating production, storage and offloading (FPSO) vessel to the offshore Terra Nova field. The Terra Nova will proceed southeast through Bull Arm, then northeast out of Trinity Bay, then heads southeast to the Jeanne d'Arc Basin on the Grand Banks. The Terra Nova is expected to produce 115,000 barrels of oil per day for six years, when it reaches full capacity. The consortium, headed by Petro-Canada as senior ownership partner and operator, built an environment protection program into every aspect of the project. Some of the features of the environment protection program include glory holes excavated on the ocean floor for the protection of production equipment from icebergs, to a flare stack on the platform, which has four legs to provide stability in rough seas. The FPSO was designed to withstand sea ice, icebergs, and severe winter storms. Flow lines are also protected, and in the event that a line is damaged, ...

2001-01-15

336

Primary spinal epidural extraosseous Ewing's sarcoma: Report of five cases and literature review  

International Nuclear Information System (INIS)

Ewing's sarcoma is the most common malignant bone tumour occurring in children and adolescents and exists in two different clinico pathological entities: osseous Ewing's sarcoma (OES) and extraosseous Ewing's sarcoma (EES). Five cases of primary epidural EES are described, which presented with non-specific symptoms leading to a long diagnostic delay. The median age at diagnosis was 22 years (range 13-36 years). The median diagnostic delay was 3 months. All patients had one or more neurological deficits. All underwent surgical exploration with a laminectomy and partial resection followed by adjuvant radiotherapy to a dose of 46-50 Gy and chemotherapy with VAC (vincristine, adriamycin and cyclophosphamide) alternating with ICE (ifosphamide, cisplatin and etoposide) for at least six cycles. The mean follow-up period is 21.2 months (range 11-32 months). Four of the five patients achieved a complete remission and are disease free at the time of writing this report. Two ...

2001-08-01

337

Internal dose from tritium at Wolsung nuclear power plant  

International Nuclear Information System (INIS)

Tritium is produced in large quantities at heavy water nuclear power reactors via the neutron activation reaction "2H(n,#gamma#)"3H. At Wolsung nuclear power plant which has a CANDU reactor, the tritium concentrations in coolant and in moderator systems are 1.5 Ci/Kg-D_2O and 35 Ci/kg-D_2O, respectively, after 12 years of operation. The airborne tritium concentration in main access area is normally less than 5 MPCa except short-term peaks. The average tritium concentrations in main access controlled areas are normally less than 100 MPCa. Tritium is mainly present in the air of workplace of CANDU reactors as a tritiated water vapour. Airborne tritiated water vapour enters the workers body via inhalation and absorption through skin and can result in a significant dose. The occupational doses from tritium at Wolsung NPP have been maintained below 1 man-Sv per year so far. The tritium contribution to the total plant man-Sv changes between 30 percent and 50 percent. For the mitigation of ...

1995-02-01

338

Development of bioenergy technology for rural micro mills production of milk, ice and bio fertilizer; Desenvolvimento de tecnologia de bioenergia rural para micro usinas de producao de leite, gelo e bio fertilizante  

Energy Technology Data Exchange (ETDEWEB)

The generation of thermal energy is the great importance for the agribusiness of dairy industry to conservation the quality of milk, taking into account that the electricity is the main source currently used for the thermal energy input. The small agribusiness dairy industry currently practiced in Brazil faces several problems related to the cost of electricity and the distance of rural properties of networks of power. In the current scenario of Brazilian dairy production, there is need for the generation of cold for the milk cooling, and also the heat for the production of hot water around 50 deg C to 60 deg C and also for cleaning of equipment used for milk production and processing. The main objective of this study is the modeling and simulation of integrated recovery process of solid waste, effluents and bioconversion. The specific project objectives are: comparison study of options and technological routes of low cost material for power generation using conventional and innovative ...

2008-07-01

339

Climate change impacts and adaptation : a Canadian perspective  

International Nuclear Information System (INIS)

This book summarizes the research that has been conducted in Canada over the past five years on the issue of climate change impacts on key sectors such as water resources, agriculture, forestry, fisheries, coastal zones, transportation, and human health and well-being. The book refers to the growing evidence that climate change is occurring. The Intergovernmental Panel on Climate Change (IPCC) believes that these changes have already contributed to increases in annual precipitation, cloud cover and extreme temperatures over the last 50 years. It suggests that it in order to develop an effective strategy for adaptation, it is necessary to understand the vulnerability of each sector to climate change in terms of the nature of climate change, the climatic sensitivity of the region being considered, and the capacity to adapt to the changes. Adaptation will require a reduction in greenhouse gas emissions in order to lower the rate of climate change. Problems associated with water resources ...

340

Texture development of ARB processed Mg/Al multilayers  

International Nuclear Information System (INIS)

Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong decrease of both textures, whereas Mg has always a much stronger ...

2010-07-01

341

Structure evolution of the LiMnO{sub 2} lamellar oxide during electrochemical cycling; Evolution structurale de l`oxyde lamellaire LiMnO{sub 2} lors du cyclage electrochimique  

Energy Technology Data Exchange (ETDEWEB)

The LiMnO{sub 2} lamellar oxide, obtained by exchange reaction from its sodium homologue {alpha}-NaMnO{sub 2}, has been used as a positive electrode for lithium batteries. After the first electrochemical cycle, the shape of the potential-composition curve changes and indicates a change in the structure. This modification changes imperceptibly at each cycle and after about 40 cycles, a stationary state is reached. Powder spectra refinement using the Rietvelt method shows a migration of manganese ions from the thin sheets towards the inter-sheet space. After a single cycle, 8% of the manganese ions are already present in the lithium site and this rate reaches 13% after 3 cycles. During long cycling, a redistribution of ions and vacancies inside the cfc oxygenated pile leads to a structure very similar to the LiMn{sub 2}O{sub 4} spinel. This structure evolution is to be compared with the one obtained from the orthorhombic variety of LiMnO{sub 2} ...

1996-12-31

342

Nuclear Data Sheets for A = 166  

Energy Technology Data Exchange (ETDEWEB)

Nuclear structure data pertaining to all known A = 166 nuclides (Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, W, Re, Os, Ir, Pt) have been compiled and evaluated, and incorporated into the ENSDF data file. This evaluation for A = 166 supersedes the previous publication (E.N. Shurshikov and N.V. Timofeeva, Nuclear Data Sheets 67, 45 (1992) (literature cutoff date 1 October 1990)) and the revision by C.M. Baglin of {sup 166}W (literature cutoff data 16 April 2000). It includes literature available by 1 March 2008. Subsequent to the previous evaluation, {sup 166}Gd has been observed for the first time and the first observations of excited states in {sup 166}Tb, {sup 166}Re, {sup 166}Os and {sup 166}Ir have been reported: also, knowledge of collective structure in {sup 166}Dy. {sup 166}Ho, {sup 1676}Er, {sup 166}Tm, {sup 166}Yb, {sup 166}Lu, {sup 166}Hf, and {sup 166}Ta has been considerably expanded. However, the structure suggested here for {sup 166}Re is highly tentative ...

2008-02-06

343

Microstructure evolution and fracture behavior in superplastic deformation of hot-rolled AZ31 Mg alloy sheet  

Energy Technology Data Exchange (ETDEWEB)

Fine-grained AZ31 magnesium alloy sheets were prepared through hot rolling process. The superplastic properties of hot-rolled AZ31 Mg alloy was examined by uniaxial tensile tests at a temperature range 250{proportional_to}450 C and strain rate range 0.7 x 10{sup -3}{proportional_to}1.4 x 10{sup -1} s{sup -1}. Optical and scanning electronic microscope (SEM) were used to observe the microstructure evolution and fracture behavior in superplastic deformation of AZ31 Mg alloy and the values of deformation activation energy at various temperatures were calculated. It is demonstrated that, the hot-rolled AZ31 alloy begins to exhibit superplasticity from 300 C and a maximum elongation of 362.5% is obtained at 400 C and 0.7 x 10{sup -3} s{sup -1}. In the temperature range 300{proportional_to}400 C, the dominant superplastic deformation mechanism is grain boundary sliding (GBS) controlled by grain boundary diffusion and the influence of temperature on the fracture behavior ...

2005-07-01

344

Free air flows for the removal of pollutants from car parks; Air-conditioning systems without sheet metal ducts as an alternative to transverse ventilation with sheet-metal ducts. Pt. 1. Freie Luftstroemungen entsorgen Parkraeume; RLT-Anlagen ohne Blechkanaele als Alternative zur Querlueftung mit Blechkanaelen. T. 1  

Energy Technology Data Exchange (ETDEWEB)

In car parks of considerable length, the removal of exhaust emissions, is carried out by air-conditioning systems mainly through transverse ventilation over short routes. The required air-conditioning ducts frequently produce a reduction in the available parking space simply due to their presence, resulting in restrictive effects on the level of acceptance by the users. In such cases, remedial action can be taken by creating ductless longitudinal ventilation. Depending on the required room air quality in the zones with the highest level of pollution, the volumetric flows for longitudinal disposal are no greater than those for conventional transverse ventilation. In conjunction with architecturally clear and positive lighting designs, clearly laid out car parks with a friendly atmosphere can be created which the user will be pleased to accept. (orig./BWI)

1994-03-01

345

Formation of high resistivity regions in [ital p]-type Al[sub 0. 5]In[sub 0. 5]P by ion implantation  

Science.gov (United States)

Ion implantation has been applied to magnesium-doped Al[sub 0.5]In[sub 0.5]P to produce high resistivity regions for the first time. Hydrogen, oxygen, and argon ions were implanted at a base dose ranging from 5[times]10[sup 12] to 5[times]10[sup 14] cm[sup [minus]2] and annealed from 400 to 900 [degree]C. Hydrogen did not appreciably compensate the In[sub 0.5]Al[sub 0.5]P layer while oxygen and argon produced sheet resistances up to 1[times]10[sup 9] [Omega]/[open square]. After annealing at 800 [degree]C, regions with high dose oxygen implants maintained a sheet resistance above 1[times]10[sup 7] [Omega]/[open square], while regions with high dose argon implants recovered most of the unimplanted conductivity.

1993-12-06

346

Experimental study on the flow boiling heat transfer enhancement and pressure drop due to the bubble behavior restricted by a screen sheet; Kanaami ni yoru kiho kyodo seigen ni tomonau futtoryu dennetsu sokushin to ryudo sonshitsu ni kansuru jikkenteki kenkyu  

Energy Technology Data Exchange (ETDEWEB)

A unique method, previously proposed by the author, was applied to the heat transfer augmentation in the flow boiling field. In this method a screen sheet was put on the horizontal heated surface where bubble nucleation occurred. Generated vapor bubbles were trapped between the screen and the wall, became flat and moved along the surface. This restricted bubble behavior caused the heat transfer enhancement. Three types of the screen were tested in the present experiment and the effect of the screen was investigated on the heat transfer and two-phase flow characteristics. In two cases of them, the screen was displaced upward by the bubble nucleation. Compared with the ordinary flow boiling case, heat transfer was enhanced by a factor of 1.2 to 6 within the present experimental range. By using a simple flow model, it was made clear that the effect of the height of the displaced screen was important to evaluate the increase in pressure drop. (author)

2000-03-25

347

Evaluation of advanced technologies for power transformers. Final report  

Energy Technology Data Exchange (ETDEWEB)

The high insulating strength of certain gases, such as sulfur hexafluoride, when used at high pressure, suggests that there may be advantages to compressed gases as the insulating fluid in power transformers. However, simply exchanging the oil for compressed gas in an otherwise conventional transformer design will not yield a significant overall advantage. Compressed gases present the engineer with properties which are quite different from mineral oil. If gases are to be used as the major insulating fluid in power transformers, then virtually all aspects of the insulation and cooling of the apparatus must be reconsidered, affording an opportunity to introduce new design concepts, new materials, and new construction techniques. In this program, the feasibility of using the following principal design concepts has been explored: sheet conductors for the windings; a system of sealed, self-contained, annular cooling ducts containing circulating cooling fluid to cool the ...

1981-01-01

348

Electrical and structural properties of ion-implanted and post-annealed silicide films  

Energy Technology Data Exchange (ETDEWEB)

The changes in the electrical and structural properties of metal-silicide films caused by ion implantation and subsequent thermal annealing have been investigated. Epitaxial silicide films such as those of CoSi/sub 2/, NiSi/sub 2/ and Pd/sub 2/Si grown on Si(111) substrates were implanted with Ar ions and annealed in a vacuum furnace at temperatures ranging from 200 to 800/sup 0/C. Rutherford backscattering and channeling techniques and the four-point probe method were used to measure the crystalline quality and the sheet resistance of the films, respectively. It was found that the sheet resistances of CoSi/sub 2/, NiSi/sub 2/ and Pd/sub 2/Si films were increased by factors of 70, 6, and 3, respectively, by implantation to a dose of 1 x 10/sup 16/ Ar-ions/cm/sup 2/, but that they were almost restored by subsequent annealing to the values before implantation. A phase transformation from Pd/sub 2/Si to PdSi was also observed in the ...

1982-05-01

349

Electrical and structural properties of ion-implanted and post-annealed silicide films  

International Nuclear Information System (INIS)

The changes in the electrical and structural properties of metal-silicide films caused byion implantation and subsequent thermal annealing have been investigated. Epitaxial silicide films such as those of CoSi"2, NiSi"2 and Pd"2Si grown on Si(111) substrates were implanted with Ar ions and annealed in a vacuum furnace at temperatures ranging from 200 to 800_0C. Rutherford backscattering and channeling techniques and the four-point probe method were used to measure the crystalline quality and the sheet resistance of the films, respectively. It was found that the sheet resistances of CoSi"2, NiSi"2 and Pd"2Si films were increased by factors of 70, 6, and 3, respectively, by implantation to a dose of 1 x 10_1_6 Ar-ions/cm_2, but that they were almost restored by subsequent annealing to the values before implantation. A phase transformation from Pd"2Si to PdSi was also observed in the high-temperature annealing of the implanted Pd"2Si films. ...

350

Effect of rolling conditions on microstructure and mechanical properties of AZ31 Mg alloy  

Energy Technology Data Exchange (ETDEWEB)

The effect of warm rolling under various conditions on the microstructure and mechanical property was investigated using an AZ31 Mg alloy sheet. Several processing parameters such as initial thickness, thickness reduction by a single pass rolling, rolling temperature, roll speed, and roll temperature were varied to elicit an optimum condition for the warm rolling process of AZ31 Mg alloy. Microstructure and mechanical properties were measured for specimens subjected to rolling experiments of various conditions. Warm rolling of 30% thickness reduction per pass was possible without any side-crack at temperatures as low as 200 C under the roll speed of 30 m/min. The initial microstructure before rolling was the mixed one consisting of partially recrystallized and cast structures. Grain refinement was found to occur actively during the warm rolling, producing a very fine grain size of 7 {mu}m after 50% reduction in single pass rolling at 200 C. Yield strength of 204 ...

2005-07-01

351

Development of a high performance air heater through use of an evacuated tube cover design  

Science.gov (United States)

Development of a high performance air heater through use of an evacuated tube cover design is described. The cover design utilizes evacuated fluorescent light tubes laid parallel in a close packed array to form an inner transparent glazing over a conventional metal absorber plate with flow behind the plate. A tempered flat glass plate was used as an outer glazing. Both clear and infrared reflective (IR) tubes were investigated. Solar transmittance tests indicate that the clear tube array has a higher transmittance than two flat sheets of low-iron glass. The IR coating produced substantial transmittance loss. Thermal conductance tests indicate that the tubes behave similar to two flat glass sheets with a vacuum in between. The IR reflective coating was only marginally effective at reducing heat conductance. Final prototype designs are presented along with collector performance estimates.

1980-01-01

352

Development of Mg alloy sheets via strip casting  

Energy Technology Data Exchange (ETDEWEB)

AZ31 and experimental ZMA611 alloys were strip cast into 2 mm thick strips. The as-cast AZ31 alloy strip consists of columnar dendrites. On the other hand, as-cast ZMA611 alloy strip shows equiaxed dendritic structure through the thickness of strip. These alloys were subjected to various thermomechanical treatments and their tensile properties were evaluated. Strip cast AZ31 alloy in H24 condition has equivalent yield and tensile strengths with similar ductility compared to commercial ingot cast AZ31-H24 alloy, indicating that strip casting is a viable process for the fabrication of Mg alloy strips. The ZMA611 alloy has a large volume fraction of fine dispersoid particles in the microstructure, resulting from the beneficial effect of strip casting on microstructural refinement. It has been shown that the ZMA611 alloy has superior tensile properties compared to commercial ingot cast AZ31-H24 alloy, suggesting the possibility of the development of new wrought Mg alloy ...

2005-07-01

353

Detection of Second-Layer Corrosion in Aging Aircraft  

International Nuclear Information System (INIS)

The Compton backscatter technique has been applied to lap-joint in aircraft structure in order to determine mass loss due to exfoliative corrosion of the aluminum alloy sheet skin. The mass loss of each layer has been estimated from Compton backscatter A-scan including the aluminum sheet, the corrosion layer, and the sealant. A Compton backscattering imaging system has been also developed to obtain a cross-sectional profile of corroded lap-splices of aging aircraft using a specially designed slit-type camera. The camera is to focus on a small scattering volume inside the material from which the backscattered photons are collected by a collimated scintillator detector for interpretation of material characteristics. The cross section of the layered structure is scanned by moving the scattering volume through the thickness direction of the specimen. The theoretical model of the Compton scattering based on Boltzmann transport theory is presented ...

2009-12-01

354

Behavior at under-film corrosion tips of Zn-Fe alloy coated steel sheets. Zn-Fe gokin mekki koban no tomakushita fushoku ni okeru fushoku sentanbu no kyodo  

Energy Technology Data Exchange (ETDEWEB)

From a macroscopic point of view, corrosion of Zn alloy coated steel sheet occurs by the coating preceding corrosion mechanism; microscopically, however, the coated layer corrosion velocity in the tip of corrosion is different. In order to find the main factors of under-film corrosion of Zn and Zn-Fe alloy coatings in the salt water spray atmospheric exposure test, the correlation between point inflation-exfoliation width and chlorine penetration behavior, point adhesion, and the difference in chlorine penetration behavior due to alloy coating components were investigated. Consequently, the following results were obtained: 1. The better correlation was observed between chlorine penetration distance and point inflation-point exfoliation width. 2. The durability of coating against chlorine penetration improved by increase in point adhesion and Zn content in the coating layer. 3. Zn-Fe (10-20%) alloy coating showed better durability against chlorine penetration than ...

1990-09-01

355

Amyloidosis  

International Nuclear Information System (INIS)

The subjects covered in this Symposium range through almost every clinical medical specialty. From an average of one paper in each of the past three Symposiums, the explosive interest in cerebral amyloidosis has led to the presentation of 12 papers on this subject in the present volume. The genetically predisposed familial amyloidotic processes, such as the polyneuropathies and familial Mediterranean fever have also stimulated extensive and intriguing investigations which have revealed the striking effect of a single amino acid substitution in transforming a normal protein into a lethal ''amyloidogenic'' one. This Symposium clearly depicts the advances since the first amyloid fibril protein was definitively identified and defined 14 years ago. Since all amyloid fibril proteins so far described are variants of normal proteins, attention to gene abnormalities now becomes a significant focus as well as the pathogenic sequences which lead in these cases to twisted #BETA#-pleated ...

1984-11-09

356

A mechanistic understanding of the formability of magnesium: examining the role of temperature on the deformation mechanisms  

Energy Technology Data Exchange (ETDEWEB)

The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. The experimental ...

2003-07-01

357

Virtual and resonance levels in screened Coulomb potentials  

International Nuclear Information System (INIS)

Two methods for computation of real, virtual and quasistationary energy eigenvalues are considered: summation of divergent perturbation series, solution of integral equations for t matrix on physical and nonphysical sheets of energy. The results of energy computation for s-, p- and d-states in potentials of a screened Coulomb type are presented. It is shown on an example of the Yukawa potential that the energy eigenvalues given by both these methods coincide with high precision. As an illustration the positions of real (deuteron) and virtual (singlet deuteron) poles of the np-scattering amplitude are calculated. For Yukawa type potentials the new theorem of symmetry for bound and virtual levels is discussed.

2003-09-01

358

Texture of YBa_2Cu_3O_7_-_x superconductor thick films  

International Nuclear Information System (INIS)

YBa_2Cu_3O_7_-_x thick films have been deposited on silver sheets and MgO single crystals by spray pyrolysis. Film texture is related to film thickness and sintering temperature. The X-ray intensity ratio of the 005 peak to the 110 peak is higher for thin films deposited at the higher temperatures. However, elevated temperatures promote copper diffusion and second-phase formation in films deposited on silver. Films deposited on MgO can have larger grain sizes and are more oriented than those deposited on silver.

1991-05-02

359

State-of-the-art in photovoltaic research and application (except for use in concentrators)  

Energy Technology Data Exchange (ETDEWEB)

A review is given of the state-of-the-art of single and polycrystalline solar cells, which includes a short theoretical review, laboratory achievements, and production methods. The Si single and polycrystalline cell and the amorphous Si cell are described, including material preparation, crystal and sheet growth, and cell and panel production. Promising second generation thin film solar cells including GaAs, CdS(CuInSe/sub 2/), and CdTe are briefly described. Economical aspects are discussed.

1987-01-01

360

Solutions of the pion dispersion equation in the medium new aspects  

CERN Document Server

In symmetrical nuclear matter the solutions of pion dispersion equation are investigated in the complex plane of the pion frequency $\\omega$. There are three well-known branches of solutions on the physical sheet : sound, pion and isobar, at the matter density less than the critical one $\\rho <\\rho_c$. At the condition $\\omega^2_c\\leq0$ (in general case Re$ \\omega^2_c\\leq0$) takes place. This points out the instability of the ground state which is possibly related to the pion condensation.

2000-01-01

361

Secondary side concept to prevent steam generator tube corrosion  

International Nuclear Information System (INIS)

Some examples are given of design adaptations, e.g. U-bend support, tube spacer grid, flow distribution baffle, triangular tube pitch, tube-tubeplate sheet connection, which reduce the tendency to various types of corrosion (stress corrosion cracking, tube denting, tube wastage, intergranular cracking). A basic diagram of the secondary circuit is shown. Oxygen, corrosion product and impurity control in the secondary circuit is described. (E.J.). 19 figs., 6 refs.

1989-05-01

362

SP-700 titanium alloy data sheets  

International Nuclear Information System (INIS)

SP-700, an emerging #beta#-rich #alpha#+#beta# titanium alloy, is designed to improve superplastic formability as well as mechanical properties over Ti-6Al-4V alloy. Owing to its fine microstructure and low #beta#-transus temperature, it is superplastic-formable at temperature below 1,073K (800 C) with low flow stress. Remarkable workability of this alloy is also retained in conventional Manufacturing processes. Another advantage of SP-700 is heat treatment response which includes deep hardenability and quick aging kinetics. Corrosion resistance and machinability are equivalent to or better than Ti-6Al-4V alloy.

1993-02-21

363

Radon in the office environment  

Energy Technology Data Exchange (ETDEWEB)

The results of weekly radon concentration measurements in an office environment using a novel envelope-type radon monitor for short-term exposure periods are presented. The commercially available LR-115 damage track detectors are used and the chemically etched sheets are spark counted. The measurements were made over a period of one year. The indoor radon concentration varies from {approx} 20 Bq.m{sup -3} to {approx} 300 Bq.m{sup -3} with the average of 130, 81 and 73 Bq.m{sup -3} for three different rooms resulting in the annual dose of 4.5, 2.8 and 2.5 mSv, respectively. (author)

1992-07-01

364

Protocol for the E-Area Low Level Waste Facility Disposal Limits Database  

Energy Technology Data Exchange (ETDEWEB)

A database has been developed to contain the disposal limits for the E-Area Low Level Waste Facility (ELLWF). This database originates in the form of an EXCEL{copyright} workbook. The pertinent sheets are translated to PDF format using Adobe ACROBAT{copyright}. The PDF version of the database is accessible from the Solid Waste Division web page on SHRINE. In addition to containing the various disposal unit limits, the database also contains hyperlinks to the original references for all limits. It is anticipated that database will be revised each time there is an addition, deletion or revision of any of the ELLWF radionuclide disposal limits.

2006-01-31

365

Nuclear data sheets for A = 177  

International Nuclear Information System (INIS)

Nuclear structure information for all nuclei with mass number A = 177 is summarized. Data from various decay and reaction experiments are compared. Evaluated data and the adopted spin, parity, and Nilsson--state assignments are given. Deviations from the regional trend of Nilsson ground-state assignments are noted for "1"7"7W and "1"7"7Re. Similar shifts have been observed in this region for nuclei 8 to 10 neutrons removed from the #beta#-stability line. In all cases, low-lying K/sup #pi#/ = 1/2/sup +-/ orbitals move to ground. Data received prior to February 1975 were included. (auth).

366

Hall mobility minimum of temperature dependence in polycrystalline silicon  

Science.gov (United States)

Molten zone recrystallized as well as sheet grown polycrystalline silicon has shown a minimum in the temperature dependence of the Hall mobility. In order to explain this experimental finding a new model is proposed, which is based on negatively charged grain boundaries for the p-type silicon material under study. This results in a potential well at the grain boundaries instead of the more generally observed potential barrier. A key feature in the model is that the space charge density at the grain boundary depends on the Fermi level position and therefore on temperature. In addition, the change in the measured Hall mobility before and after hydrogen passivation of the grain boundaries is discussed.

1998-01-01

367

From Earth to Mars in 15 days with an americium-propelled space ship; De la terre a mars en 15 jours avec un vaisseau spatial propulse a l'americium  

Energy Technology Data Exchange (ETDEWEB)

This digest paper presents the theoretical project of a fission engine for space ship as imagined by Y. Ronen from the Ben-Gourion Univ. (Israel). In this engine, the combustion chamber is covered with metastable {sup 242}Am thin sheets. The fission reaction is triggered with a bombardment of neutrons and the fission fragments ionize a gas (hydrogen, for instance) which is overheated and ejected through the engine nozzle. (J.S.)

2002-01-01

368

Energy balances of OECD countries 1970/1982  

Energy Technology Data Exchange (ETDEWEB)

The present volume provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD Countries. It covers the years 1970 to 1982 year by year and includes many revisions and additions to data previously published. The balances in the present volume are based on data published in OECD Energy Statistics 1971-1981 and OECD Energy Statistics 1981-1982. Tables for each OECD Country include production, import, export, consumption by the different industries, transportation, agriculture, residential sector of the different energies: solid fuels, petroleum, gas, nuclear power and hydroelectricity.

1984-01-01

369

Diffusion bonding on superplastic-aluminum and -magnesium alloys  

Energy Technology Data Exchange (ETDEWEB)

The superplastic characteristics and diffusion bonding behaviors were investigated in commercial 7475 aluminum alloy and AZ31 magnesium alloy sheets. In this study, the presently used materials behaved in a superplastic manner at {proportional_to} 773 K (7475Al) and {proportional_to} 523 K (AZ31). Then, by the theoretical relationship between pressure and time, these materials were successfully diffusion bonded at the superplastic temperatures. The bonding strength was more than 65 MPa. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

2004-07-01

370

Construction: Masonry. Secondary Schools. Curriculum Guide.  

Science.gov (United States)

This construction curriculum guide on masonry for secondary students is one of six developed for inservice teachers at Marianas High School in Saipan. The guide provides the rationale, description, goals, and objectives of the program; the program of studies and performance objectives by levels; samples of lesson plans for effective delivery of instruction; and a listing of references. Concepts covered include orientation to masonry construction, safety, tools and equipment, cement, concrete, concrete block masonry, concrete forms, and concrete reinforcement. Appended materials include transparency copies, tests and answer keys, information sheets, and student activities. (CT)

1980-08-01

371

Adsorption rate of gas on various materials  

Energy Technology Data Exchange (ETDEWEB)

This paper described experiments on the adsorption of radon gas on surfaces of various materials. The experiments were carried out on three kinds of materials: Poly(vinyl chloride), polyethylene and stainless steel. On stainless steel, adsorption was not detectable. On the other hand, there was clearly adsorption on poly(vinyl chloride) and polyethylene. A poly(vinyl chloride) sheet of one square meter surface in a 5.3 L container absorbed approximately 20% of the radon. Radon adsorption has to be taken into account when radon concentration measurements in the air. (author)

2003-01-01

372

A two-cycle process for enhanced actinide separation from radioactive liquid wastes  

Energy Technology Data Exchange (ETDEWEB)

A two-cycle process using O{Phi}CMPO and HDEHP as extractants to achieve an alpha decontamination factor of HLLW greater than 10{sup 3} together with a reduction of the lanthanides/americium weight ratio by a factor of about 200 is considered. Experimentally measured distribution ratios have been employed as input data of a suitable computer code to define operating conditions and M/S stage numbers of a process flow-sheet able to meet the above-mentioned objectives.

1996-09-01

373

A horizontal steam generator for the Indian 235 MW heavy water nuclear power plants  

International Nuclear Information System (INIS)

In this paper the thermal design of a horizontal steam generator for the Indian PHWR nuclear power plant is described. The main attraction is absence of tube sheet and use of stainless steel 'U' tubes. It is emphasised that with appropriate water chemistry it is possible to use stainless steel tubes, which is many times cheaper than the Incoloy tubes used elsewhere. The design approach, applicable equation for the design and the results of computation in the form of heat transfer area and some important dimensions of the steam generator are presented.

1993-11-01

374

Zn-Al alloy as a new anode-metal of a zinc-air battery  

Energy Technology Data Exchange (ETDEWEB)

Low operating power and short cycle life are 2 of the main draw-backs of zinc-air batteries, despite the fact that various attempts have been made to develop improved zinc (Zn) anodes. This study investigated the performance of a Zn anode with a substantial addition of aluminium (Al). Rolled sheets of Zn-Al alloys of varying amounts of Zn and Al were used to prepare the anodes. Results of the study showed that the cells had higher open circuit voltages (OCV) values as well as a higher specific anode capacity. It was observed that specific anode capacity increased with higher current loading. The Zn{sub 59}Al{sub 41} and Zn{sub 67}Al{sub 33} sheets showed the highest performance with high OCV values of between 1540 and 1560 mV, as well as the largest specific anode capacity of 750-800 mAh per g at a discharge current of 200 mA. The 2-phase structure of the Zn-Al sheets was considered to be useful in reducing ...

2006-01-15

375

The corrosion behaviour of nanocrystalline PVD model steel films. Influence of structure and Molybdenum content; Das Korrosionsverhalten von nanokristallinen PVD-Modellstahlschichten. Einfluss der Struktur und des Molybdaen-Gehaltes  

Energy Technology Data Exchange (ETDEWEB)

By magnetron sputtering model steel films with specific properties can be prepared for purposive surveys. By changing the deposition parameters certain properties of these films can be influenced. For this thesis steel films with 18% Cr and 8% Ni have been prepared in order to study specific parameters on the corrosion resistance of bulk stainless steel. Chemical composition, microstructure, and surface morphology of these films have been characterized. In comparison to bulk steel sheets with the same chemical composition they have a smaller grain size and a ferritic structure. In contrast to bulk steel sheets they don`t contain any nonmetallic inclusions like Mn-sulfides. The influence of these structural differences on the corrosion resistance has been studied. For this purpose the electrochemical properties of the sputter-deposited steels have been compared with the properties of steel sheets with a similar chemical ...

1995-12-31

376

Surface modification of PTFE sheet by synchrotron radiation in the soft X-ray region  

International Nuclear Information System (INIS)

Full text: The surface properties of poly (tetrafluoroethylene) (PTFE) are changed by the exposure to synchrotron radiation (SR). We succeeded in controlling the wettability of the PTFE surface from hydrophobic to hydrophilic by varying the substrate temperature during the SR irradiation and found that the wettability was ascribable to microstructure and chemical composition of surface.In these previous works, oxygen atoms were found to inhabit on the hydrophobic surface of PTFE. In this study, we investigated the surface modification of PTFE from the SR exposure experiment under the O_2 gas atmosphere. The SR exposure to the PTFE sheet was carried out at beamline 6 (BL6) of the New- SUBARU. The PTFE sheet was irradiated to the white beam, ranging 50-1000 eV at BL6 at room temperature. The gas cell was mounted at the irradiation chamber. The O_2 gas pressure in the gas cell can be maintained at about 0.20 Pa during the SR exposure using 5mm ...

2004-07-19

377

Structural and electrical characteristics of epitaxial CoSi{sub 2} grown on n-Si{sub 0.83}Ge{sub 0.17}/n-Si(001) by reactive chemical vapor deposition using a Si capping layer  

Energy Technology Data Exchange (ETDEWEB)

Epitaxial cobalt disilicide (CoSi{sub 2}) layers are grown on n-Si{sub 0.83}Ge{sub 0.17}/n-Si(001) using a sacrificial Si capping layer at the growth temperature T{sub s}=650 deg. C by reactive chemical vapor deposition using cyclopentadienyl dicarbonyl cobalt (Co({eta}{sup 5}-C{sub 5}H{sub 5})(CO){sub 2}). Structural and electrical properties of epi-CoSi{sub 2}/Si{sub 0.83}Ge{sub 0.17}/Si(001) were measured by transmission electron microscopy, X-ray diffraction, Auger electron spectroscopy and sheet resistance measurement as a function of annealing temperature. The combined results showed that the epitaxial CoSi{sub 2} phase by the reaction of Co with the Si capping layer was formed in the as-grown layers. Rapid thermal anneals for the investigation of thermal stability of the as-grown layers showed good thermal stability of the epitaxial CoSi{sub 2} layers with the low sheet resistance value as low as congruent with 4.4 {omega}/cm up to the ...

2004-06-30

378

Structural and electrical characteristics of epitaxial CoSi_2 grown on n-Si_0_._8_3Ge_0_._1_7/n-Si(001) by reactive chemical vapor deposition using a Si capping layer  

International Nuclear Information System (INIS)

Epitaxial cobalt disilicide (CoSi_2) layers are grown on n-Si_0_._8_3Ge_0_._1_7/n-Si(001) using a sacrificial Si capping layer at the growth temperature T_s=650 deg. C by reactive chemical vapor deposition using cyclopentadienyl dicarbonyl cobalt (Co(#eta#"5-C_5H_5)(CO)_2). Structural and electrical properties of epi-CoSi_2/Si_0_._8_3Ge_0_._1_7/Si(001) were measured by transmission electron microscopy, X-ray diffraction, Auger electron spectroscopy and sheet resistance measurement as a function of annealing temperature. The combined results showed that the epitaxial CoSi_2 phase by the reaction of Co with the Si capping layer was formed in the as-grown layers. Rapid thermal anneals for the investigation of thermal stability of the as-grown layers showed good thermal stability of the epitaxial CoSi_2 layers with the low sheet resistance value as low as congruent with 4.4 #OMEGA#/cm up to the annealing temperature as high as 850 deg. C without ...

2004-06-30

379

Processing and properties of Nb-Ti-base alloys  

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep test at 650 C and 172 MPa was conducted on the base alloy, which contained 40Nb-40Ti-10Al-10Cr. A second alloy was modified with 0.11 at.% C and 0.07 at.% Y. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1,100 C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1,000 C and for the modified alloy at room temperature, 400, 600, 700, and 800 C. Oxidation tests the base alloy and modified alloy, as measured by weight change, were carried out at 600, 700, 800, and 900 C. Both the base alloy and the modified alloy were ...

1993-08-01

380

Processing and properties of Nb-Ti based alloys  

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep tests at 650{degrees}C and 172 MPa was conducted on the base alloy which contained 40Nb-40-Ti-10Al-10Cr. A second alloy was modified with 0.11 at. % carbon and 0.07 at. % yttrium. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1100{degrees}C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1000{degrees}C, and for the modified alloy at room temperature, 400, 600, 700, and 800{degrees}C. Oxidation tests on the base alloy and modified alloy, as measured by weight change, were carried out at 600, 700, 800, and ...

1992-01-01

381

Paper-based, printed zinc-air battery  

Energy Technology Data Exchange (ETDEWEB)

A flexible battery is printed on paper by screen-printing a zinc/carbon/polymer composite anode on one side of the sheet, polymerising a poly(3,4-ethylenedioxythiophene) (PEDOT) cathode on the other side of the sheet, and applying a lithium chloride electrolyte between the two electrodes. The PEDOT cathode is prepared by inkjet printing a pattern of iron(III)p-toluenesulfonate as a solution in butan-1-ol onto paper, followed by vapour phase polymerisation of the monomer. The electrolyte is prepared as a solution of lithium chloride and lithium hydroxide and also applied by inkjet printing on to paper, where it is absorbed into the sheet cross-section. Measurements on a zinc/carbon-PEDOT/air battery in a similar configuration on a polyethylene naphthalate substrate shows a discharge capacity of up to 1.4 mAh cm{sup -2} for an initial load of 2.5 mg zinc, equivalent to almost 70% of the zinc content of the anode, which ...

2009-12-01

382

A Conceptual Design of Light-weighted Mobile Robot for the Integrity of SG Tubes in NPP  

International Nuclear Information System (INIS)

Steam generators (SG) are among the most critical components of pressurized water Nuclear Power Plants (NPP). SG tubes must provide a reliable pressure boundary between the primary and secondary cooling water. It is because that any leakage from tube defects could result in the release of radioactivity to the environment. Thus degradations of steam generators tubes should be monitored and inspected periodically under nuclear regulatory. In-service inspections of SG tubes are carried out using eddy current test (ECT) and the defected tubes are usually plugged. Because the radioactivity in the internal of SG chambers limits free access of human worker, remote manipulators are required. In South Korea, Manipulators such as the Zetec SM series and the Westinghouse ROSA series have been used. Such manipulators are rigidly mounted to manways or tube sheets of SG. Confusions for the inspected tubes may occur from deflection of the manipulators. To reduce the deflections ...

2010-10-01

383

White River Falls Fish Passage Project, Tygh Valley, Oregon : Final Technical Report, Volume III, Appendix B, Fisheries Report; Appendix C, Engineering Alternative Evaluation; Appendix D, Benefit/Cost Analysis.  

Energy Technology Data Exchange (ETDEWEB)

Studies were conducted to describe current habitat conditions in the White River basin above White River Falls and to evaluate the potential to produce anadromous fish. An inventory of spawning and rearing habitats, irrigation diversions, and enhancement opportunities for anadromous fish in the White River drainage was conducted. Survival of juvenile fish at White River Falls was estimated by releasing juvenile chinook and steelhead above the falls during high and low flow periods and recapturing them below the falls in 1983 and 1984. Four alternatives to provide upstream passage for adult salmon and steelhead were developd to a predesign level. The cost of adult passage and the estimated run size of anadromous fish were used to determine the benefit/cost of the preferred alternative. Possible effects of the introduction of anadromous fish on resident fish and on nearby Oak Springs Hatchery were evaluated. This included an inventory of resident species, a genetic ...

1985-06-01

384

Tritium in surface waters, tap water and in precipitation in Poland during the 1994-1999 period  

International Nuclear Information System (INIS)

Concentrations of tritium in environmental waters (precipitation, rivers, lakes, tap water) have been determined using electrolytic enrichment and liquid scintillation counting. In waters of big rivers (the Vistula and the Odra rivers), lakes and tap water the annual average concentrations were similar to each other being from 1.4 to 1.9 Bq x dm"-"3. These concentrations were similar to those in the precipitation in which they ranged from 1.7 to 2.2 Bq x dm"-"3. The lowest tritium concentrations were found in waters of the Seashore Region rivers (average for 1994-1999 was 1.1 Bq x dm"-"3). The tritium concentrations in surface waters and in precipitation are still higher than that of natural level. The data obtained show that tritium concentration in the water of rivers might depend on the size of drainage area. The observed seasonal variations of tritium concentration in the precipitation collected in Warsaw and at the Mount Sniezka indicate the stratospheric ...

2001-01-01

385

The use of low sulphide tailings as the moisture retaining layer in engineered cover systems to prevent AMD  

Energy Technology Data Exchange (ETDEWEB)

One of the main problems facing the mining sector is the production of acid mine drainage (AMD), which is caused by the oxidation of sulphide minerals in the presence of water. AMD can have a detrimental effect on the environment. One solution is to use soil covering over the materials that cause acid to limit the gas flux by diffusion. A capillary barrier effect is generated by using various layers of different types of soil. In the composite system till and clay normally form the basis of the fine material layer. The use of low sulphide tailings to replace the use of fine grained soil was studied to evaluate its effectiveness. Following both in situ and laboratory experiments spread over an eight-year period, the results indicated that an effective method to limit the oxygen flux and generation of AMD is the use of non-acid generating tailings as the moisture retaining layer. The main concepts that form the basis of the study, analysis and design of covers with ...

2000-07-01

386

Silica Polyamine Composites: New Supramolecular Materials for Cation and Anion Recovery and Remediation  

Energy Technology Data Exchange (ETDEWEB)

The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR resonances than the linear polymers poly(allylamine) (PAA) and poly(vinylamine) (PVA). These results are understood in terms of the low energy conformations calculated from molecular modeling studies. Three new ...

2006-03-01

387

Sensitivity Study for CFD Analysis on Debris Transport to ECCS Sump for CANDU Type Plant in Korea  

International Nuclear Information System (INIS)

Once containment recirculation pumps are activated and emergency core cooling (ECC) flow is supplied from the recirculation sump during loss of coolant accident (LOCA), various insulations and coatings on a pipe, equipments and structures damaged by LOCA break jet as well as additional debris sources are transported to recirculation sump screen by the break flow and containment spray flow drainage. This debris may result in loss of net pressure suction head (NPSH) of the recirculation pumps, and have a threat to long term cooling and containment heat removal capacity. In this case, flow patterns of containment pool are important to confirm behaviors of debris transport for predicting various flow paths to the recirculation sump screen. In this paper, models using commercial computational fluid dynamics (CFD) software CFX are developed for containment pool simulation during recirculation mode. The specific plant used for this analysis is CANDU type plant, in Korea

2010-10-01

388

SAGD or cold production : a case study for an Orinoco heavy oil field  

Energy Technology Data Exchange (ETDEWEB)

This paper examined the potential of steam assisted gravity drainage (SAGD) technology for increasing productivity in the Orinoco heavy oilfields of Venezuela. A computerized simulation tool was used to generate a matrix of parameters needed to compare SAGD processes with cold production techniques in the Carabobo region of the Orinoco belt. Parameters included vertical connectivity, oil saturation, and net pay. Monte Carlo simulations and uncertainty assessments were used to generate cold production scenarios. Optimized SAGD scenarios were then designed for each case. Results of the study suggested that vertical local connectivity was an important parameter for the identification of suitable areas for EOR and SAGD. Unfavorable conditions for the application of SAGD during early production stages were identified. SAGD behaviour improved through the adjustment of injection rates during different stages of the process. It was concluded that the simulation run times ...

2008-07-01

389

Role of unsaturated soil in a waste containment system  

Energy Technology Data Exchange (ETDEWEB)

The role of the unsaturated properties of sand as a drainage layer in a composite liner system for landfills is investigated. The effect of the unsaturated properties of coarse-grained soil on contaminant migration was evaluated by means of a series of simulations using a one-dimensional model of a two- and a three-layer soil liner system for advection and diffusion, respectively. The results showed that under seepage conditions, the effect of an unsaturated sand layer on the advancement of the concentration front was quite insignificant. The arrival time of the C/C{sub o} = 0.5 concentration front increased from 651 days for the case with no sand layer to approximately 951 days for the case with a 1.0-m sand layer. A steady-state flow condition was ultimately established in the sand, and this fact suggests that the capillary action might not be effective. For diffusion, the arrival time of the concentration front increased nonlinearly with a decrease in the degree ...

1996-12-31

390

Recommendations to the NRC for review criteria for alternative methods of low-level radioactive waste disposal: Task 2b: Earth-mounded concrete bunkers  

International Nuclear Information System (INIS)

The US Army Engineers Waterways Experiment Station (WES) and US Army Engineer Division, Huntsville (HNDED) have developed general design criteria and specific design review criteria for the earth-mounded concrete bunker (EMCB) alternative method of low-level radioactive waste (LLW) disposal. An EMCB is generally described as a reinforced concrete vault placed below grade, underneath a tumulus, surrounded by filter-blanket and drainage zones. The tumulus is covered over with a low permeability cover layer and top soil with vegetation. Eight major review criteria categories have been developed ranging from the loads imposed on the EMCB structure through material quality and durability considerations. Specific design review criteria have been developed in detail for each of the eight major categories. 63 refs., 13 figs., 2 tabs.

391

Proceedings of the 58. annual technical meeting of the Petroleum Society of CIM : CIPC 2007 : Because technology changes everything  

International Nuclear Information System (INIS)

This conference and trade show provided a forum to present new, emerging and existing technologies that will play a key role in ensuring that hydrocarbon exploitation occurs in a sustainable manner, where costs and resource recovery are optimized while minimizing environmental impacts. The challenge of developing maturing basins, frontier lands and unconventional resources was discussed. In particular, the application of thermal recovery methods such as steam assisted gravity drainage (SAGD) for the in-situ recovery of heavy oils and bitumens was reviewed and compared with the performance of alternative enhanced energy recovery technologies such as vapor extraction (VAPEX). The conference was attended by local and international participants in the petroleum sector, including managers, engineers, technologists, geologists, and other petroleum industry specialists. The conference featured 132 presentations addressing topics such as improved recovery of conventional ...

2007-06-12

392

Prediction of monitoring data for 239Pu accidentally injected via wound site based on the proposed NCRP wound model.  

Science.gov (United States)

In response to the consultation from the National Council on Radiation Protection and Measurements (NCRP) to the International Commission on Radiological Protection (ICRP) committee 2, retention and excretion of 239Pu deposited at wound site were calculated by coupling together the proposed NCRP wound model and the current ICRP systemic model of Pu. The physicochemical forms considered were the soluble form categorized into 'Strong Retention', and the colloidal, particulate and fragmentary forms. The results are summarized as follows. If in soluble form, immediate medical intervention is needed to prevent uptake of radionuclides to body tissues, and prompt wound monitoring is essential for an accurate estimation of the initially deposited radioactivity. If in particulate form, a multi-component exponential equation leads to an overestimation of the absorption rate to blood because of significant lymph node drainage. The committed doses in the organs for direct ...

2007-06-07

393

Physico-chemical behaviour of a barrier composed of cement kiln dust and fly ash; Comportement physico-chimique d'une barriere a base de poussieres de four de cimenterie et de cendres volantes  

Energy Technology Data Exchange (ETDEWEB)

Controlling acid mine drainage is one of the most important challenges facing the mining industry. One of the solutions to this problem is the use of soil covers. In this poster presentation, the author described the development of a soil barrier composed of cement kiln dust and fly ash. In the study, four different cement kiln dust were associated to three different fly ash types, for a total of twelve different mix. The objective was to develop a stable environmental barrier. The origin of the cement kiln dust was described, followed by the characterization and preparation of the different mix, and the monitoring of the hydration process. The results were discussed, and indicated that a barrier composed of cement kiln dust and fly ash seemed to have great potential. The results also indicated that the fly ash improve the properties of the cement kiln dust, but that the improvement was dependent on the nature of the fly ash. 22 figs.

2000-07-01

394

Hydrologic analysis for ecological risk assessment of watersheds with abandoned mine lands  

International Nuclear Information System (INIS)

As part of on-going study of acid mine drainage (AMD), a comprehensive ecological risk assessment was conducted in the Leading Creek Watershed in southeast Ohio. The watershed is influenced by agriculture and active and abandoned coal-mining operations. This work presents a broad overview of several quantitative measures of hydrology and hydraulic watershed properties available for in risk assessment and evaluates their relation to metrics of ecology. Data analysis included statistical comparisons of metrics of ecology, ecotoxicology, water quality, and physically based parameters describing land use, geomorphology, flow, velocity, and particle size. A multiple regression analysis indicated that abandoned mining operations dominated impacts upon aquatic ecology. It also indicated low flow velocity measurements and a ratio of maximum velocity to average velocity at low flow where helpful in describing variation in macroinvertebrate Total Taxa scores. Other key ...

1999-07-25

395

Hepatobiliary scintigraphy in current pediatric practice  

Energy Technology Data Exchange (ETDEWEB)

Hepatobiliary scintigraphy is the only non-invasive technique providing real-time assessment of hepatocytes function and bile progression from the liver to the intestine; for this reason it is of great importance in the study of jaundice and many other disorders of the liver and the biliary tract in children. Ultrasonography is the initial method of evaluating the intra- and extrahepatic bile ducts dilatation: the differential diagnosis between biliary atresia and neonatal hepatitis cannot however be done without hepatobiliary scintigraphy. Cystic fibrosis patients also require hepatobiliary scintigraphy; liver and biliary tract disease can really occur independently of the underlying disease severity and the presence of steatorrhoea. Hepatobiliary imaging in children who have undergone liver transplantation is of major importance; it can assess vascularity, parenchymal function biliary drainage, possible presence of a bile leak and obstruction; it has very good ...

1998-06-01

396

Findings of the wetland survey of the David Witherspoon, Inc., 1630 Site, South Knoxville, Knox County, Tennessee  

Energy Technology Data Exchange (ETDEWEB)

In accordance with Department of Energy (DOE) Regulations surveys for wetland presence or absence were conducted in September 1996 on the DWI-1630 site (Witherspoon Landfill) located in South Knoxville, Knox County, Tennessee. The DWI-1630 site includes a closed, capped landfill area, areas of past disturbance adjacent to the capped area, and patches of hardwood forest. Wetlands were identified on the landfill cap and in a small bottomland that was formerly used for a retention pond in the southwest corner of the DWI-1630 site. The wetlands identified on the cap are man-induced, atypical situation wetlands. These areas have hydrophytic vegetation and wetland hydrology, but the soils do not have hydric characteristics. Wetland development appears to be due to a combination of the grading or subsidence of the clay landfill cap, the low permeability of the clay fill soil, and the absence of surface drainage outlets from the depressions. These atypical situation ...

1997-03-01

397

Fifteenmile Basin habitat enhancement project.; TOPICAL  

International Nuclear Information System (INIS)

The Fifteenmile Basin Habitat Improvement Project is an ongoing multi-agency effort to improve habitat in the Fifteenmile drainage and increase production of the depressed wild, winter steelhead run. Cooperating agencies include the Oregon Department of Fish and Wildlife, USDA Forest Service. USDA Soil Conservation Service and Bonneville Power Administration. in consultation with the Confederated Tribes of Warm Springs. The Oregon Department of Fish and Wildlife is administering project work on state and private lands and the U.S.D.A. Forest Service is administering project work on National Forest land. Project work on the Forest has been sub-divided into four components; (1) Ramsey Creek, (2) Eightmile Creek, (3) Fifteenmile Creek, and (4) Fivemile Creek. Forest Service activities in the Fifteenmile basin during 1988 involved habitat improvement work on Ramsey Creek, continuation of physical and biological monitoring, collection of spawning survey information, and ...

398

Environmental status of Technical Area 49, Los Alamos, New Mexico  

Energy Technology Data Exchange (ETDEWEB)

A series of experiments involving high explosives and radioactive materials were conducted at Los Alamos, New Mexico, primarily to understand certain safety aspects of operational nuclear weapons. The experiments were conducted underground in large diameter holes as deep as 120 ft. The location was selected because it had geologic and hydrologic characteristics that assured complete containment of the experiments and precluded any possible contamination of groundwater. Important features verified by the USGS included the absence of any recharge and about 1200 feet of dry rock above the groundwater aquifer. Residual materials dispersed by detonation of the high explosives remain at the bottom of the experimental holes. The materials of significance from an environmental standpoint include about 40 kg of plutonium, 93 kg of enriched uranium, at least 82 kg of depleted uranium, 13 kg of beryllium, and an undetermined amount of lead. Environmental monitoring has been carried out regularly ...

1987-11-01

399

Distinction of mining lakes in central Germany with remote sensing methods  

Energy Technology Data Exchange (ETDEWEB)

Mining lakes are of a world-wide challenging problem caused by the well known acid mine drainage (AMD) and the dynamics of it. In the past, there was no possibility to monitor these mining lakes for an investigation of chemical and biological parameters. But, in general, remote sensing methods are suitable for a monitoring of natural lakes, and now, at the first time, those can be used for a distinction of acid mining lakes in central Germany into different types. In acid mining lakes unusual absorption and scattering properties exist due to the water constituents which are quite different in their optical properties to those of natural lakes. The artificial lakes show high concentrations of metal ions and compounds. This fact was used to discriminate the mining lakes into initial stage, early stage, transitional state and late state. The result is a map of the area where the mining lakes are presented at their current stage. The present method is a proven solution ...

2001-07-01

400

Diagnostic imaging and interventional radiology of the amoebic liver abscess. Personal experience; Diagnostica per immagini e radiologia interventistica degli ascessi amebici del fegato: esperienza personale  

Energy Technology Data Exchange (ETDEWEB)

The diagnostic imaging findings in hepatic amoebiasis and the capabilities of percutaneous drainage have already been described but some debate is open on both diagnosis and treatment. It is reported the experience with the ultrasound (US) and Computed Tomography (CT) studies of the hepatic amoebic abscess and its management. [Italian] I reperti con diagnostica per immagini nell'amebiasi epatica e le possibilita' del drenaggio percutaneo sono stati gia' illustrati; esistono tuttavia controversie sul piano sia diagnostico che terapeutico. Obiettivo di questo lavoro e' quello di riportare l'esperienza personale nella diagnostica con ecografia e tomografia computerizzata (TC) e nel trattamento degli ascessi amebici del fegato.

1999-10-01

401

Designing a healthy house - an overview  

Energy Technology Data Exchange (ETDEWEB)

There are certain factors to take into account when determining the suitability of a healthy house site. Power lines, agricultural spraying, vehicle exhaust, and industrial pollution are all potential sources of indoor air contamination. It is recommended that a environmental assessment be done to determine whether there are specific sources of contamination. Good drainage is required. The surrounding landscaping should be open and sunlit, and with low maintenance requirements. Decks and fences made from pressure-treated or chemical treated lumber should be avoided. One of the early decisions in the design process is the choice of the structural system. The key with all foundation types is to control moisture, whether from rain, from the ground, or the condensation of moisture from the air with cooling. The construction frame is sealed away from the occupants by the air/vapor barrier, so only in extreme cases is it essential to use alternatives to softwood lumber ...

1999-11-01

402

Base Program on Energy Related Research: Quarterly report, August 1-October 31, 1994  

Energy Technology Data Exchange (ETDEWEB)

This document describes research performed at the Morgantown Energy Technology Center in the areas of oil and gas, advanced systems application, environmental technologies, applied energy science and remediation. The following subtasks are described: CROW{sup TM} Process Modeling, Development of a Portable Data Acquisition System and Coalbed Methane Simulator, Tank Bottom Waste Processing using the TaBoRR{sup TM} Process, Process Support and Development, Eastern Shale Oil Residue as an Asphalt Additive, Solid Waste Management, Remediation of Contaminated Soils, The Syn-Ag{sup TM} Process: Coal Combustion Ash Management Option, the Maxi-Acid{sup TM} Process: In- sit Amelioration of Acid Mine Drainage, Spill Test Facility Database, Heavy Oil/Plastics Co-Processing, Fossil Fuel and Hydrocarbon Conversion Using Hydrogen-Rich Plasmas, and North Site Remediation.

1994-12-31

403

Air-side performance of a parallel-flow parallel-fin (PF{sup 2}) heat exchanger in sequential frosting  

Energy Technology Data Exchange (ETDEWEB)

The thermal-hydraulic performance in periodic frosting conditions is experimentally studied for the parallel-flow parallel-fin heat exchanger, henceforth referred to as a PF{sup 2} heat exchanger, a new style of heat exchanger that uses louvered bent fins on flat tubes to enhance water drainage when the flat tubes are horizontal. Typically, it takes a few frosting/defrosting cycles to come to repeatable conditions. The criterion for the initiation of defrost and a sufficiently long defrost period are determined for the test PF{sup 2} heat exchanger and test condition. The effects of blower operation on the pressure drop, frost accumulation, water retention, and capacity in time are compared under the conditions of 15 sequential frosting cycles. Pressure drop across the heat exchanger and overall heat transfer coefficient are quantified under frost conditions as functions of the air humidity and air face velocity. The performances of two types of flat-tube heat ...

2010-09-15

404

Abundance of West Nile virus mosquito vectors in relation to climate and landscape variables.  

Science.gov (United States)

It is currently unclear if the potential for West Nile virus transmission by mosquito vectors in the eastern United States is related to landscape or climate factors or both. We compared abundance of vector species between urban and suburban neighborhoods of Henrico County, VA, in relation to the following factors: temperature, precipitation, canopy cover, building footprint, and proximity to drainage infrastructure. Mosquitoes were collected throughout the 2005, 2006, and 2007 seasons and tested for West Nile virus (WNV) in pools of 10-50. Test results of mosquito pools were compared to average site abundance from 37 sites in Henrico County, VA; abundance was then examined in relation to ecological variables. Urban infrastructure was positively correlated with the abundance of Culex pipiens L./Cx. restuans, and our findings implicate combined sewer overflow systems as large contributors to Culex vector populations. No measure of urbanization examined in our study ...

2011-06-01

405

A laboratory study on the thermomechanical behaviour of clayey soils  

Energy Technology Data Exchange (ETDEWEB)

The thermomechanical behaviour of clayey soils was examined in a laboratory study because of their importance in some engineering applications such as hydrocarbon extraction from oil-bearing sands and radioactive waste disposal. The slightest temperature variations have been known to have an impact on the mechanical behaviour of clayey soils. In this study, tests were conducted on reconstituted and natural clayey soils using triaxial cells modified to control temperatures. Changes of temperature and stress state were not applied simultaneously. Instead, the tests were divided into two separate sections aimed at studying the thermal and mechanical behaviour of clays. The thermal behaviour tests examined the deformations induced by drainage temperature changes as well as pore-pressure generation and consolidation phenomena. The mechanical behaviour tests, focused on the influence of temperature and temperature history on compressibility, deformability and shear ...

2000-08-04

406

The highs and lows of water level : the vulnerability of coastal communities to water level change : final report on the C-CIARN Coastal Zone workshop  

Energy Technology Data Exchange (ETDEWEB)

The Coastal Zone Sector of the Canadian Climate Impact and Adaptation Research Network (C-CIARN) was established to address concerns regarding climate change in coastal areas. Coastal zones are sensitive to increases in air, sea and ground temperatures as well as to variations in sea level, precipitation, ice thickness, and storm intensity. This report presents the results of a workshop which focused on how coastal communities will be affected by climate induced water level changes, particularly sea-level rise on ocean coasts and decreasing lake levels in the Great Lakes. The workshop addressed issues such as the effects of changing water levels on coastal infrastructure, utilities, community development, and the implications of changing water levels to human safety, cultural resources, tourism, and insurance. The workshop reviewed the current state of understanding on water level fluctuations resulting from climate change. It also identified information and ...

2004-07-01

407

Surface morphology of thin lysozyme films produced by matrix-assisted pulsed laser evaporation (MAPLE)  

Energy Technology Data Exchange (ETDEWEB)

Thin films of the protein, lysozyme, have been deposited by the matrix-assisted pulsed laser evaporation (MAPLE) technique. Frozen targets of 0.3-1.0 wt.% lysozyme dissolved in ultrapure water were irradiated by laser light at 355 nm with a fluence of 2 J/cm{sup 2}. The surface quality of the thin lysozyme films of different thickness deposited on 7 mm x 7 mm Si-<1 0 0>-wafers was investigated with scanning electron microscopy and atomic force microscopy. Already at comparatively low thickness, {approx}20 nm, the substrate is covered by intact lysozyme molecules and fragments. The concentration of lysozyme in the ice matrix apparently does not play any significant role for the morphology of the film. The morphology obtained with MAPLE has been compared with results for direct laser irradiation of a pressed lysozyme sample (i.e. pulsed laser deposition (PLD))

2007-12-15

408

Ship of challenges: Braced for perfect storms, icebergs and oilfield hazards  

Energy Technology Data Exchange (ETDEWEB)

More details about the construction of the Terra Nova floating production, storage and offloading (FPSO) vessel are provided. The vessel was built in the Daewoo shipyard in South Korea, and is now undergoing final fitting at Bull Arm, near St. John's, Newfoundland. When complete, the vessel will operate 350 km offshore, southeast of St. John's. It is 291 metres long and 45.5 metres wide and has a capacity of 960,000 barrels of oil. Although the FPSO will hold less than half of the last giant supertanker which sailed for Irving Oil, it has a crew of 81, four times the size of the supertanker, reflecting the technical uniqueness of the vessel and the intense pre-occupation with safety associated with the combination of winds, ice, waves, and shallow water around the Grand Banks. Also described is the alliance system of partnership between the oil companies and the main contractors. The deal stipulates that if the project ran over its budget, the oil ...

2001-08-06

409

Report two. Safety offshore eastern Canada. Summary of studies and seminars  

Energy Technology Data Exchange (ETDEWEB)

In 1982 the semi-submersible drilling unit Ocean Ranger capsized and sank off the Grand Banks, resulting in the loss of the entire 84-man crew. A Royal Commission was set up to conduct an enquiry into the incident, and to carry out a process of research and opinion-gathering towards providing recommendations to both federal and Newfoundland governments. The primary purpose of the Commission was to determine why the Ocean Ranger sank, why none of the crew were saved, and how to avoid similar disasters. A number of studies and seminars were held to focus expert knowledge and opinion in several key fields and to update studies and fill gaps in the data base. Summaries of selected study reports and the seminar proceedings are presented in the following areas: the environment, including ice, marine climatology, weather forecasting services, wave climatology, oceanographic information, and seabed information; design, including mobile offshore drilling rig design ...

1984-05-01

410

Relative toxicities of pure propylene and ethylene glycol and formulated deicers on plant species  

Energy Technology Data Exchange (ETDEWEB)

Propylene and ethylene glycol deicers are commonly used at airports in the US and other countries to remove and retard the accumulation of snow and ice on aircraft. Deicers may not only enter water bodies without treatment, due to excessive storm-related flow, but also may expose terrestrial organisms to high concentrations through surface runoff. Most available toxicity data are for aquatic vertebrates and invertebrate species; this study examined effects on terrestrial and aquatic plants. Terrestrial plant species included both a monocot (rye grass, Lolium perenne) and a dicot (lettuce, Lactuca saliva). Aquatic species included a single cell alga (Selenastrum capricomutum), and an aquatic macrophyte (duckweed, Lemna minor). Glycol deicers were obtained in the formulated mixtures used on aircraft. Pure ethylene and propylene glycol were obtained from Sigma{reg_sign}. Parameters measured included germination, root and shoot length, survival, and growth. Formulated ...

1994-12-31

411

Phytoplankton primary production in a eutrophic cooling water pond  

Energy Technology Data Exchange (ETDEWEB)

The effect of longer ice-free periods on the seasonal variation and total annual values of phytoplankton primary production was considered along with the efficiency and productivity of the phytoplankton communities at different water temperatures by constant light. The studied pond, Vasikkalampi, is located in the town Jvyaskyla in central Finland. The pond is slightly eutrophic and its water is used for cooling purposes by a 35 MW thermal powerplant. The cooling water is taken in the middle of the pond and it returns as heated effluent to the northern part, near the surface, about 100 m from the intake pipe. This circulation and warming of the water keeps the pond open throughout the year except during the coldest weeks in the winter when some parts freeze over. The increase of the water temperature was not sufficient to be optimal for photosynthesis in the spring. The phytoplankton biomass starts to increase early in the spring when the zooplankton grazing ...

1984-01-01

412

Method of calibration to correct for cloud-induced wavelength shifts in the Aura satellite's Ozone Monitoring Instrument  

Science.gov (United States)

The in-flight wavelength calibration for the Ozone Monitoring Instrument is discussed. The observed variability in the wavelength scale is two orders of magnitude larger than caused by temperature changes in the instrument. These wavelength variations are the result of rapid changes in time in the radiance levels during an individual observation in the presence of clouds or snow and ice. We have developed a data processing method to account and correct for these changes. In February 2005 this correction was implemented in the official data processing stream. We explain in detail how and how accurately this method works. Before correction, the error in the wavelength scale can be as much as a few tenths of a pixel; after correction it is mostly less than 1/100th of a pixel, which is the required preflight accuracy. This means that higher-level products such as the total column amounts of ozone, NO2, and SO2 are not significantly affected. It is expected that these ...

2006-05-01

413

Hybrid electric vehicles and electrochemical storage systems - a technology push-pull couple  

Energy Technology Data Exchange (ETDEWEB)

In the advance of fuel cell electric vehicles (EV), hybrid electric vehicles (HEV) can contribute to reduced emissions and energy consumption of personal cars as a short term solution. Trade-offs reveal better emission control for series hybrid vehicles, while parallel hybrid vehicles with different drive trains may significantly reduce fuel consumption as well. At present, costs and marketing considerations favor parallel hybrid vehicles making use of small, high power batteries. With ultra high power density cells in development, exceeding 1 kW/kg, high power batteries can be provided by adapting a technology closely related to consumer cell production. Energy consumption and emissions may benefit from regenerative braking and smoothing of the internal combustion engine (ICE) response as well, with limited additional battery weight. High power supercapacitors may assist the achievement of this goal. Problems to be solved in practice comprise battery management to ...

1999-12-01

414

Gamma Ray Bursts from the First Stars Neutrino Signals  

CERN Document Server

If the first (PopIII) stars were very massive, their final fate is to collapse into very massive black holes. Once a proto-black hole has formed into the stellar core, accretion continues through a disk. It is widely accepted, although not confirmed, that magnetic fields drive an energetic jet which produces a burst of TeV neutrinos by photon-meson interaction, and eventually breaks out of the stellar envelope appearing as a Gamma Ray Burst (GRB). Based on recent numerical simulations and neutrino emission models, we predict the expected neutrino diffuse flux from these PopIII GRBs and compare it with the capabilities of present and planned detectors as AMANDA and IceCube. If beamed into 1% of the sky, we find that the rate of PopIII GRBs is $\\le 4 \\times 10^6$ yr$^{-1}$. High energy neutrinos from PopIII GRBs could dominate the overall flux in two energy bands [$10^4 - 10^5$] GeV and [$10^5 - 10^6$] GeV of neutrino telescopes. The enhanced sensitivities of ...

2002-01-01

415

Factors affecting actions of ethanol on GABA-activated chloride channels  

International Nuclear Information System (INIS)

Effects of ethanol in vitro on membrane vesicles were evaluated by monitoring "3"6Cl"- influx. Different assay parameters were tested to determine increased or decreased action of ethanol on GABA-activated chloride channels. The ability of 30 mM ethanol to augment "3"6Cl"- flux was seen at 0 degree C, in the absence of GABA, and at 34 degree C in the presence of GABA, using two different assay procedures. Picrotoxin blocked the direct effects of ethanol suggesting GABA_a involvement. Endogenous GABA in the medium surrounding the microsacs was assayed at different temperatures both in the presence and absence of GABA and ethanol. The direct effect of ethanol did not appear to involve the action of endogenous GABA. In addition to temperature effects on the assay, time of membrane storage also influenced ethanol action. Microsacs stored on ice for 2 hours or more lost their ability to respond to ethanol but not to GABA, pentobarbital or flunitrazepam. When these drugs ...

416

Effect of external pressure on intramuscular blood flow at rest and after running  

Energy Technology Data Exchange (ETDEWEB)

Local blood flow in the thigh was measured with /sup 133/Xe clearance technique in eight male distance runners after compression with a foam rubber compress and a standard elastic bandage. Two degrees of compression were tested, and an initial experiment with rested subjects was followed by a similar experiment immediately after running. Maximum compression exerted a cutaneous pressure of 85 (+/- 8) mm Hg and caused an immediate cessation of intra-muscular blood flow in the compressed area. Moderate compression gave a cutaneous pressure of 40 (+/- 5) mm Hg and resulted in a reduction of blood flow by approximately 50%. During compression, there were no significant differences in the blood flow of rested subjects compared to subjects immediately after running. In acute soft tissue injuries, a maximum compression bandage should effectively reduce or eliminate the formation of an intra-muscular hematoma, and an additive effect on blood flow of ice should not be ...

1987-10-01

417

Climate change: the Intergovernmental Panel on Climate Change impacts assessment  

Energy Technology Data Exchange (ETDEWEB)

The report was prepared for the IPCC by Working Group II. The remit of Working Group II was to describe the environmental and socioeconomic implications of possible climate changes over the next decades caused by increasing concentrations of greenhouse gases. The scenarios used include the following features: an effective doubling of atmospheric CO{sub 2} between now and 2025-2050; a consequent increase of global mean temperature of 1.5-4.5{degree}C; an unequal global distribution of the temperature increase; a sea level rise of 0.3 to 0.5m by 2050. The impacts of possible climate change were assessed for the following: agriculture and forestry; natural terrestrial ecosystems; hydrology and water resources; human settlements including the energy, transport and industrial sectors; human health; air quality and changes in UV-B radiation; oceans and coastal zones; seasonal snow cover; ice and permafrost. Further action is recommended. 1015 refs., 34 figs., 26 tabs.

1990-01-01

418

Climate - air traffic emissions  

Energy Technology Data Exchange (ETDEWEB)

In 1990, 176 million tonnes (mt) of air-traffic fuel was burned, which produced about 550 mt CO{sub 2}, 220 mt water, 3.5 mt NO{sub x} amd 0.18 mt SO{sub 2}. NO{sub x} emissions from air traffic may, by increasing ozone concentrations, be responsible for about 8% of global greenhouse warming. In the stratosphere NO{sub x} from aircraft is partly responsible for ozone depletion. With present technology 500 aircraft in the stratosphere would cause global ozone losses of 20%. Water vapour added by aircraft also contributes to global warming. In the form of ice crystals between 8 to 13 km above sea level, it acts as cirrus clouds. Probably the least damaging cruising altitude for aircraft is 9 km above sea level. Fuel consumption by aircraft is increasing. Air pollution abatement measures include substituting hydrogen fuel for kerosene, developing engines that emit less NO{sub x} and the introduction of internationally negotiated taxes on kerosene. 30 refs.

1991-11-01

419

A space crystal diffraction telescope for the energy range of nuclear transitions  

Energy Technology Data Exchange (ETDEWEB)

This paper contains literature from American Power Conference Air Toxics Being Measured Accurately, Controlled Effectively NO{sub x} and SO{sub 2} Emissions Reduced; Surface Condensers Improve Heat Rate; Usable Fuel from Municipal Solid Waste; Cofiring Technology Reduces Gas Turbine Emissions; Trainable, Rugged Microsensor Identifies of Gases; High-Tc Superconductors Fabricated; High-Temperature Superconducting Current Leads; Vitrification of Low-Level Radioactive and Mixed Wastes; Characterization, Demolition, and Disposal of Contaminated Structures; On-Line Plant Diagnostics and Management; Sulfide Ceramic Materials for Improved Batteries; Flywheel Provides Efficient Energy Storage; Battery Systems for Electric Vehicles; Polymer-Electrolyte Fuel Cells for Transportation; Solid-Oxide Fuel Cells for Transportation; Surface Acoustic Wave Sensor Monitors Emissions in Real-Time; Advance Alternative-Fueled Automotive Technologies; Thermal & Mechanical Process; Flow-Induced Vibration ...

1995-04-01

420

The role of interventional radiology in management of patients with end-stage renal disease  

Energy Technology Data Exchange (ETDEWEB)

The aim of the paper is to review the role of interventional radiology in the management of hemodialysis vascular access and complications in renal transplantation. The evaluation of patients with hemodialysis vascular access is complex. It includes the radiology/ultrasound (US) evaluation of the peripheral veins of the upper extremities with venous mapping and the evaluation of the central vein prior to the access placement and radiological detection and treatment of the stenosis and thrombosis in misfunctional dialysis fistulas. Preoperative screening enables the identification of a suitable vessel to create a hemodynamically-sound dialysis fistula. Clinical and radiological detection of the hemodynamically significant stenosis or occlusion demands fistulography and endovascular treatment. Endovascular prophylactic dilatation of stenosis greater than 50% with associated clinical abnormalities such as flow-rate reduction is warranted to prolong access patency. The technical success ...

2003-05-01

421

Biogeochemistry of the compost bioreactor components of a composite acid mine drainage passive remediation system  

International Nuclear Information System (INIS)

The compost bioreactor ('anaerobic cell') components of three composite passive remediation systems constructed to treat acid mine drainage (AMD) at the former Wheal Jane tin mine, Cornwall, UK were studied over a period of 16 months. While there was some amelioration of the preprocessed AMD in each of the three compost bioreactors, as evidenced by pH increase and decrease in metal concentrations, only one of the cells showed effective removal of the two dominant heavy metals (iron and zinc) present. With two of the compost bioreactors, concentrations of soluble (ferrous) iron draining the cells were significantly greater than those entering the reactors, indicating that there was net mobilisation (by reductive dissolution) of colloidal and/or solid-phase ferric iron compounds within the cells. Soluble sulfide was also detected in waters draining all three compost bioreactors which was rapidly oxidised, in contrast to ferrous iron. Oxidation and hydrolysis of iron, ...

2005-02-01

422

Thermal neutron capture gamma-rays  

Energy Technology Data Exchange (ETDEWEB)

The energy and intensity of gamma rays as seen in thermal neutron capture are presented. Only those (n,..cap alpha..), E = thermal, reactions for which the residual nucleus mass number is greater than or equal to 45 are included. These correspond to evaluations published in Nuclear Data Sheets. The publication source data are contained in the Evaluated Nuclear Structure Data File (ENSDF). The data presented here do not involve any additional evaluation. Appendix I lists all the residual nuclides for which the data are included here. Appendix II gives a cumulated index to A-chain evaluations including the year of publication. The capture gamma ray data are given in two tables - the Table 1 is the list of all gamma rays seen in (n,..gamma..) reaction given in the order of increasing energy; the Table II lists the gamma rays according to the nuclide.

1983-01-01

423

The whole risks and the choice for a type of financing; L`ensemble des risques et le choix du type de financement  

Energy Technology Data Exchange (ETDEWEB)

Energy projects are extremely capitalistic and the costs involved have a significant weight on the balance sheets of companies. This paper describes the general rules of financing policies used by companies from the natural gas and petroleum industries: constraints (external and financial markets, partnership, warranties..); implication of financiers; risk analysis (political (nationalization, civil or military troubles, difficult transfer of profits outside the project..), financial (property developer, nature of the project, delay, cost overruns, performance, market..)); financial instruments (proper funds and debt, bankers and insurers, loans etc..). These rules are illustrated with several examples of recent projects of gas pipelines and exploitation of oil fields abroad. (J.S.)

1997-07-01

424

The diffusion bonding and theoretical model including void growth mechanism in magnesium alloys  

Energy Technology Data Exchange (ETDEWEB)

There are many factors affecting diffusion bonding in order to obtain high quality joining. Therefore, in the beginning, we constructed diffusion bonding model based on void growth mechanism to predict bonding pressures and times. In addition, in order to compare theoretical values with experimental values, diffusion bonding tests were carried out by using commercial AZ31 magnesium alloy sheets with different grain sizes, 16 and 130 {mu}m. The present AZ31 alloys were successfully diffusion bonded at several conditions, and the bonding strength was more than 0.8 of each parent materials. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

2003-07-01

425

The North-West Borneo Trough  

British Library Electronic Table of Contents (United Kingdom)

The North-West Borneo Trough is bordered along its south-east margin by a melange wedge that has been the subject of disagreement with insufficient discussion. Offshore Palawan it has been interpreted as an accretionary prism that has been preserved in place when subduction ceased in the Middle Miocene. It is unconformably overlain by undeformed Upper Miocene to Holocene draping strata. Farther south-west along the Trough, the seismically identical melange wedge has been named a Major Thrust Sheet System, which was assumed to have been thrust as a nappe north-westwards over the autochthonous Dangerous Grounds terrane of attenuated continental crust of the South China Sea passive margin. The accretionary prism model is the simplest, resulting in interpretation of the North-West Borneo Troug...

2010-01-01

426

Short-term radon measurements in the workplace  

Energy Technology Data Exchange (ETDEWEB)

A novel envelope-type radon monitor has been used for short-term (as little as 1 week) radon concentration measurements in a workplace environment. The commercially available LR-115 type II damage track detector was used in this study and the chemically etched sheets were spark counted. The measurements were made over a period of 1 year in a workplace consisting of three adjacent rooms situated in the lower ground level of multistorey office building in Rome, Italy. The variations of the radon concentration are from [approx] 20 to [approx] 300 Bq m[sup -3] with averages of 130,81 and 73 Bq m[sup -3] for the three different rooms resulting in annual doses of [approx] 3.8, [approx] 2.4 and [approx] 2.2 mSv, respectively. (author) 2 figs., 9 refs.

1992-01-01

427

Shape of tachyons  

Energy Technology Data Exchange (ETDEWEB)

We study some aspects of the experimental behaviour of tachyons, in particular by finding out their <> shape. A Superluminal particle, which in its own rest frame is spherical or ellipsoidal (and with an infinite lifetime), would <> to a laboratory frame as occupying the whole region of space bound by a double cone and a two sheeted hyperboloid. Such a structure (the tachyon <>) rigidly travels with the speed of the tachyon. However, if the Superluminal particle has a finite lifetime in its rest frame, then in the laboratory frame it gets a finite space extension. As a by-product, we are able to interpret physically the imaginary units entering - as is well known - the transverse co-ordinates in the Superluminal Lorentz transformations. The various particular or limiting cases of the tachyon shape are thoroughly considered. Finally, some brief considerations concerning possible experiments to look for ...

1982-10-21

428

Serological testing-An alternative to boosters?  

British Library Electronic Table of Contents (United Kingdom)

The issue of the duration of immunity, particularly for the modified live viral components of veterinary vaccines, has been a significant part of the recent vaccination debate. One manufacturer has increased the recommended booster interval for these components to 3 years give name and another now states `up to 4 years' immunity.There remain many unanswered questions regarding this duration of immunity (DOI). Studies suitable for data sheet claims are time consuming and costly and can only be performed in laboratory dogs under tightly controlled conditions. Evidence from rabies serology testing in the UK shows that the response of individual animals to routine vaccination is highly variable. Much of the published field evidence on the persistence of antibody titres originates from North Am...

2006-01-01

429

Saturation of relativistic Weibel instability and the formation of stationary current sheets in collisionless plasma  

International Nuclear Information System (INIS)

We have studied the features of formation and the possible stationary structures of a self-consistent magnetic field in a relativistic collisionless plasma, which are characteristic of a simple geometry of the Weibel instability that is well known in the nonrelativistic case. The universal condition is established, the growth rate is determined, and the criteria of saturation of the Weibel instability are analyzed for a broad class of anisotropic particle distribution functions (for definiteness, in application to an electron-positron plasma). A nonlinear equation of the Grad-Shafranov type describing the potential current structures is derived and its solutions are analytically studied. Special attention is paid to spatially harmonic, nonlinear current configurations with parameters determined by the properties of the initial homogeneous plasma subject to the Weibel instability. It is demonstrated that the magnetic field energy density in the obtained solutions (both harmonic and ...

2008-12-01

430

Recent progress in energy-filtered high energy X-ray photoemission electron microscopy using a Wien filter type energy analyzer  

International Nuclear Information System (INIS)

Energy-filtered X-ray photoemission electron microscopy (EXPEEM) is a microscopy technique which has the potential to provide surface chemical mapping during surface chemical processes on the nanometer scale. We studied the possibilities of EXPEEM using a Wien filter type energy analyzer in the high energy X-ray region above 1000 eV. We have successfully observed the EXPEEM images of Au islands on a Ta sheet using Au 3d_5_/_2 and Ta 3d_5_/_2 photoelectron peaks which were excited by 2380 eV X-rays emitted from an undulator (BL2A) at Photon Factory. Our recent efforts to improve the sensitivity of the Wien filter energy analyzer will also be discussed.

2004-10-15

431

Preparations and removal of spent nuclear fuel of WWR-2 and DR research reactors of the RRC Kurchatov Institute for reprocessing  

International Nuclear Information System (INIS)

Peculiarities of Kurchatov Institute WWR-2 and TR research reactors spent fuel treating and transportation for radiochemical processing are stated. Spent fuels were performed as fuel assemblies of different forms and containing similar fuel elements: EhK-10 with 10% enrichment UO2-Mg fuel kernels or S-36 with 36% enrichment U-Al alloys. Spent fuel storage conditions are described. Features of developed procedures for identification of fuel assemblies by type of fuel elements are given. Transport package TUK-19 for loading and transportation of spent fuel for processing was chosen. Details of spent fuel loading in TUK-19 that is conducted by personnel under protective sheet of water in special reclaim volume are described

2009-04-01

432

Preparation and properties of environmental friendly nonhalogen flame retardant melamine cyanurate/nylon 66 composites  

British Library Electronic Table of Contents (United Kingdom)

Abstract Melamine cyanurate (MCA) was utilized as an environmental friendly additive to prepare the nonhalogen flame retardant MCA/Nylon 66 composites by melt blending technique. Because of the strong hydrogen bond interactions and fine interfacial compatibility between MCA and Nylon 66, the resultant even dispersion of MCA filler in polymer matrix leads to the better toughness and strength of MCA/Nylon 66 composites than those of neat Nylon 66. Both Nylon 66 and MCA/Nylon 66 composites exhibit similar -crystalline structure, but the presence of MCA influences the distribution of 1 and 2 crystalline phases in Nylon 66 by inducing its hydrogen-bonded sheet separation. Moreover, the blending of MCA and Nylon 66 increases the crystallization temperature and exothermicity but decreases the the...

2011-01-01

433

Precipitation of ions induced by nonadiabatic motion in the outer cusp region  

Science.gov (United States)

The transport of magnetospheric particles in the outer cusp region is examined by means of three-dimensional single particle codes. It is shown that, at high altitudes, particles can experience nonadiabatic motions leading to significant magnetic moment changes. It is demonstrated that this nonadiabatic behavior can be interpreted, at least partly, by the action of an impulsive centrifugal force perturbing the particle gyromotion. Systematic trajectory calculations reveal that plasma sheet ions which ExB convert toward the magnetopause from low L-shells in the dayside sector are subjected to such nonadiabatic motions. As a result of magnetic moment damping, a number of them are injected into the loss cone and subsequently precipitate near the cusp equatorward edge.

434

Polymers and paper as packaging materials of irradiated food  

International Nuclear Information System (INIS)

Effects of #gamma#-irradiation on synthetic polymers and paper used as packaging materials for irradiated food have been studied by NMR. Polystyrene, polybutadiene and some copolymers were studied before and after the #gamma#-irradiation treatment and in the presence or absence of antioxidants and stabilisers. In the absence of additives, the effect of #gamma#-irradiation on polystyrene is negligible even irradiating at high doses. In turn, the role of antioxidants and stabilisers is crucial in polybutadiene and butadiene-containing copolymers. Wood pulp paper was also studied by NMR. Preliminary measurements on #gamma#-irradiated wood pulp sheets show a shortening in the T_2 relaxation time component due to the bound water, i.e. some of the bound water is lost. (author)

2000-03-01

435

Politics and instruments for a sustainable development  

International Nuclear Information System (INIS)

The new industrial political tools based on the sustainable development of productive activities, and originating at the Rio Conference in 1992, late introduced by the EU, the Government and voluntary organizations (ISO, CEM, UNI) are gradually entering the market, thereby underling their effect in terms of industrial competitiveness. The main tools were examined in the report and mostly refer to the voluntary ones which, in surpassing the 'command and control' logic, increasingly tend to get close to traditional fiscal, tariff and financial ones. Voluntary agreements, environmental management systems (EMAS, norme ISO 14001), the risk prevention systems (UNI 10617), certification (Ecolabel, ISO 14040) and environment communication tools (environment balance sheet, environmental report, environmental statement) are synthetically described.

436

Optimizing boron junctions through point defect and stress engineering using carbon and germanium co-implants  

International Nuclear Information System (INIS)

We report the fabrication of p"+/n junctions using Ge"+, C"+, and B"+ co-implantation and a spike anneal. The best junction exhibits a depth of 26 nm, vertical abruptness of 3 nm/decade, and sheet resistance of 520 Ohm/square. The junction location is defined by where the boron concentration drops to 10"1"8 cm"-"3. These junctions are close to the International Technology Roadmap specifications for the 65 nm technology node and are achieved by careful engineering of amorphization, stresses, and point defects. Advanced simulation of boron diffusion is used to understand and optimize the process window. The simulations show that the optimum process completely suppresses the transient-enhanced diffusion of boron and the formation of boron-interstitial clusters. This increases the boron solubility to 20% above the equilibrium solid-state solubility.

2005-08-01

437

Navy Occupational Health Information Management System (NOHIMS). Hazardous Materials Control Module. Users' manual  

Energy Technology Data Exchange (ETDEWEB)

The Hazardous Materials Control Module (HMC) is one module of four for the Industrial Health component. The HMC module was designed to inform employees of health and safety hazards in the workplace and to track the movement of hazardous materials through the facility. The module performs these functions by maintaining health and safety data on hazardous materials used in the facility, and by tracking who requests information about any hazardous materials. The HMC module gets its information from two sources. The first one is the Hazardous Materials Information System (HMIS), this is a national system that is used by the Department of Defense. It is loaded on to the system via tapes that contain all safety, health and transportation information about a particular product. The second is Material Safety Data Sheets (MSDS) that are procured by a particular site. This information is manually entered into their own personal system, which they give a site specific ...

1987-01-16

438

MA28: a set of Fortran subroutines for sparse unsymmetric linear equations. Revision  

Energy Technology Data Exchange (ETDEWEB)

In this report we present a suite of subroutines for the solution of sparse unsymmetric sets of linear equations using a variant of Gaussian elimination. The subroutines are divided into three distinct phases. The first phase optionally preorders the matrix to block triangular form and then performs a sparsity oriented factorization, the second factorizes a matrix of a similar sparsity pattern, while the third uses these decompositions to solve the equations. In this revised edition, the actual Fortran listings have been replaced by a reference to their availability in machine readable form. Other changes to the first edition are minor. This revision is essentially a reprint of the 1979 revision, the only changes being that the MA28A specification sheet has been typeset and has a few minor changes and the existence of a version of the package for complex equations is announced. 11 refs., 11 tabs.

1980-11-01

439

Internal friction of amorphous Pd/sub 80/ Si/sub 20/ metal doped with hydrogen isotopes  

Energy Technology Data Exchange (ETDEWEB)

Internal friction of amorphous Pd/sub 80/Si/sub 20/ metal doped with hydrogen or deuterium was measured with a specially designed apparatus using amorphous metal sheet as a part of the electric oscillating circuit. Two peaks in Q/sup -1/ curve are observed. Applying the peak shift method to the first Snoek-like peak, we can determine the relaxation time from which the microdiffusion coefficient can be calculated. The obtained microdiffusion coefficient is about 10/sup -14/ m/sup 2//s at 200 K, being comparable with the macrodiffusion coefficient obtained from the releasing method. It can, however, not elucidate the hydrogen isotopic effect on the peak temperature of Q/sup -1/ curve, the activation energy for relaxation and the relaxation time from the present work because of the broadness of obtained Q/sup -1/ curve.

1983-02-01

440

Influence of host periosteum and recipient bed perforation on the healing of onlay mandibular bone graft: an experimental pilot study in the sheep  

British Library Electronic Table of Contents (United Kingdom)

Purpose The aim of this study was to evaluate the role of host periosteum and recipient bed perforation on the healing of an onlay graft to the mandible based on histologic and immunohistochemical analysis. Materials and methods Each of the 12 adult sheep used in the study received four iliac corticocancellous onlay bone grafts on the lateral surface of the mandible. In experiment 1, the block graft was placed in direct contact with the recipient bed and fixed with micro-screws, and in experiment 2, the recipient cortical bed was perforated before graft placement. The host periosteum around the graft was excised before flap replacement in experiment 3, and in experiment 4, a sheet of silicone membrane was placed between the graft and the recipient bed. The animals were euthanised at 4, 8, ...

2008-01-01

441

Hydrogen effect on cold rolling texture of stable #beta#-titanium alloy  

International Nuclear Information System (INIS)

A study was made into microstructure and texture of cold rolled titanium alloy VT-35 with various hydrogen content aimed to reveal hydrogen influence on the mechanism of cold plastic deformation by rolling. Experiments were carried out using sheets 1.2 mm thick hydrogenated up to hydrogen concentrations from 0.06 to 0.554 mass. %. All specimens constituted a single-phase FCC #beta#-solid solution. It is shown that small hydrogen additions have a plasticizing effect on #beta#-titanium alloys in their cold rolling. The character of texture is dependent on hydrogen concentration and determined by deformation mechanism. 6 refs.; 5 figs.

442

Fracture behavior under dynamic biaxial stress on magnesium alloy  

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

2004-07-01

443

Evaluation, testing and database generation of pitting corrosion characteristics of domestic steam generator tubing material  

Energy Technology Data Exchange (ETDEWEB)

Accumulation of Chloride and Cupric ions under the sludge on the steam generator tubing surface in the area between tube sheet and the first tube support is known to be the main reason for the pitting corrosion. In addition to those ions, oxygen, pH, temperature, heat treatment history, contests of minor elements such as C, S or Ti in the alloy are also influencing the material's the pitting corrosion resistance. a series of autoclave pitting test was conducted to evaluate the pitting corrosion characteristics of the domestically produced alloy 690 tubing material and compare with that of INCO manufactured material. 16 refs., 44 figs., 5 tabs. (Author)

1998-04-01

444

Energy management, real estate management, and facility management; Energiemanagement in der Immobilienverwaltung  

Energy Technology Data Exchange (ETDEWEB)

The publication presents an outline of the subject of energy management and attempts to test the hypotheses that targeted knowledge management may result in new developments and potentials, and if these are at all desirable. On this basis, a knowledge management system will be developed that may effectively promote developments and potentials in the field of energy management. The tools and fundamentals of energy management are looked into, and the given situation and desired goals are identified by means of an enquiry. This is a scientific study that aims at providing empirical information on the situation and views on the subject of energy management. The analysis, which is supported by an enquiry sheet, is to provide a basis for testing the assumed hypothesis. Further, the potential acceptance and utilization potential of decisive knowledge management in the facility and real estate management sector are to be tested. The energy knowledge management system ENWI ...

2010-07-01

445

Early development of the digestive tract (pharynx and gut) in the embryos and pre-larvae of the European sea bass Dicentrarchus labrax  

British Library Electronic Table of Contents (United Kingdom)

The European sea bass Dicentrarchus labrax is a marine teleost important in Mediterranean aquaculture. The development of the entire digestive tract of D. labrax, including the pharynx, was investigated from early embryonic development to day 5 post hatching (dph), when the mouth opens. The digestive tract is initialized at stage 12 somites independently from two distinct infoldings of the endodermal sheet. In the pharyngeal region, the anterior infolding forms the pharynx and the first gill slits at stage 25 somites. The other three gill arches and slits are formed between 1 and 5 dph. Posteriorly, in the gut tube region, a posterior infolding forms the foregut, midgut and hindgut. The anus opens before hatching, at stage 28 somites. Associated organs (liver, pancreas and gall bladder) ar...

2009-01-01

446

Direct strip casting of magnesium  

Energy Technology Data Exchange (ETDEWEB)

A new interest in magnesium alloys has arisen since light-weight constructions have become more and more attractive. Products that are currently available are mostly cast, forged, and extruded. A cost-effective production of sheet metals will render new perspectives in the design of light-weight constructions. The development of new casting technologies like thin slab casting or strip casting with an in-line rolling process is expected to result in a shorter processing time featuring a high potential of saving energy, time, and cost. Particular attention is paid to the casting process parameters such as casting speed and solidification speed. This article deals with some aspects of a magnesium-adapted single-belt caster. Results of casting experiments and material examination are shown as well as some advices given concerning safety and handling of liquid magnesium. (orig.)

2004-12-01

447

Development of plasticity processing of magnesium alloys  

Energy Technology Data Exchange (ETDEWEB)

Recent developments on plastic forming technology of magnesium alloys are presented. Attempts have been undergoing with an aim at forming magnesium alloy parts at lower temperatures. It is believed that fine microstructure magnesium alloys usually have much higher plasticity at lower temperatures and even room temperatures. Extrusion is a method to form magnesium profile products and tube products, which is also one of the effective ways to make fine microstructure magnesium alloys. Superplasticity forming is another method to form high plasticity magnesium alloys. Hot forming of magnesium sheet parts is an important process to form magnesium products. Some developments related to above issues are discussed in the present paper. (orig.)

2003-07-01

448

Design and operating parameters for emission control studies: Asarco, Tacoma, copper smelter. Final task report, Apr--Oct 1975  

Science.gov (United States)

The report gives background design data for a specific copper smelter. The data is sufficiently detailed to allow air pollution control system engineering studies to be conducted. These studies will be concerned primarily with lean SO/sub 2/ streams that currently are not being captured. Physical layout of the smelter and the surrounding area is presented, along with existing control equipment. Ductwork that would be considered for future system tie-in is defined. Emissions from operating equipment, gas flow rates, temperatures, sulfur balance, and a process flow sheet are included. Utilities, stack dimensions, footing requirements, and solid waste handling are defined. Available area for new control equipment, gas characteristic variation, and potential new control equipment installation problems are discussed. Portions of this document are not fully legible. (GRA)

1976-02-01

449

Design and operating parameters for emission control studies: Asarco, Hayden, copper smelter. Final task report, Apr--Oct 1975  

Science.gov (United States)

The report gives background design data for a specific copper smelter. The data is sufficiently detailed to allow air pollution control system engineering studies to be conducted. These studies will be concerned primarily with lean SO/sub 2/ streams that currently are not being captured. Physical layout of the smelter and the surrounding area is presented, along with existing control equipment. Ductwork that would be considered for future system tie-in is defined. Emissions from operating equipment, gas flow rates, temperatures, sulfur balance, and a process flow sheet are included. Utilities, stack dimensions, footing requirements, and solid waste handling are defined. Available area for new control equipment, gas characteristic variation, and potential new control equipment installation problems are discussed. (GRA)

1976-02-01

450

Description of Cretaceous Sedimentary Sequence of the Yaojia Formation Recovered by CCSD-SK-Is Borehole in Songliao Basin: Lithostratigraphy, Sedimentary Facies and Cyclic Stratigraphy  

British Library Electronic Table of Contents (United Kingdom)

The Yaojia Formation recovered by CCSD-SK-Is borehole (China Cretaceous Continental Scientific Drilling-SongkeI-the south borehole) is 157.67 m long and 99.96% of cores recovery. The age of the formation corresponds with a range from the Santonian to the early Campanian. The sequences and processes of lithology-lithofacies and cyclic stratigraphy are revealed by a detailed core description. Eleven rock types and three kinds of sedimentary subfacies, including shallow lake, deep lake, and delta front, are recognized from the drilling core. There are eleven sedimentary microfacies including dolostone, argillaceous limestone, shallow lake turbidite, deep lake turbidite, subaqueous mouth bar, distal bar, sheet sandstone, subaqueous distributary bay, slump deposits, shallow lake mudstone, and d...

2009-01-01

451

Compression molded energy storage flywheels  

Energy Technology Data Exchange (ETDEWEB)

Flywheels containing fiber-reinforced composite materials have attributes suitable for vehicular propulsion, indicating the need for rotor designs which are easily manufactured and low in cost. This development goal was pursued in a cooperative effort between Owens-Corning Fiberglas and Lawrence Livermore Laboratory which investigated flywheels made from compression-molded sheet molding compound (SMC). The design resulted from a Lawrence Livermore analysis, with successful fabrication achieved using a procedure developed by Owens-Corning. Details concerning materials selection, rotor fabrication, and testing are discussed. Owens-Corning subsequently initiated a technical/marketing survey to determine current industrial interests in a low-cost flywheel design; precursory information, pertaining to composite flywheels in particular, is described.

1982-08-01

452

Compatibility of magnesium alloys with methanol-containing fuels  

Energy Technology Data Exchange (ETDEWEB)

Although magnesium is not attacked by hydrocarbons, it reacts vigorously with anhydrous methanol, raising concerns about the compatibility of the metal with methanol blend fuels. This paper describes the behavior of magnesium alloys in laboratory tests in static contact with methanol-containing fuels at 110/sup 0/F. Water in small concentrations (above 0.25% by weight of the methanol content) is shown to prevent the destructive attack of magnesium by these fuels. The required water content is well within the water tolerance of methanol-GTBA (gasoline grade tertiary-butyl alcohol) cosolvent fuel blends. Die cast AZ91HP shows greater resistance to methanol reaction than does AZ31B sheet.

1986-01-01

453

Collisionless driven reconnection in an open system  

Energy Technology Data Exchange (ETDEWEB)

Particle simulation studies of collisionless driven reconnection in an open system are presented. Collisionless reconnection evolves in two steps in accordance with the formation of two current layers, i.e., an ion current layer in the early ion phase and an electron current layer in the late electron phase. After the electron current layer is formed inside the ion current layer, the system relaxes gradually to a steady state when convergent plasma flow is driven by an external electric field with a narrow input window. On the other hand, when the convergent plasma flow is driven from the wide input window, magnetic reconnection takes place in an intermittent manner, due to the frequent formation of magnetic islands in the vicinity of neutral sheet. (author)

2000-06-01

454

Chemical and physical change of packaging materials for food by gamma-ray irradiation  

International Nuclear Information System (INIS)

Recently, foods are often exposed to radiation under packed states with various wrapping materials. In this study, the effects of #gamma#-ray radiation were investigated on the additives in wrapping materials on the market. 10 - 50 kGy #gamma# radiation was irradiated to samples under sealed condition in a glass-ware. Polyethylene bag and wrapping film, polypropylene wrapping film, cup and sheet, and polystyrene cup were used as samples. And the additives in these materials were analyzed by GC/MS to evaluate the radiation effects on them. The irradiation was found to induce rapid degradation of antioxidants, especially, Irgafos 168. Some fatty acid amides used as a lubricant and a plasticizer, DBP were also reduced, but not aliphatic hydrocarbons. However, all polystyrene products used in this study included no additives. The contents of styrene dimer and trimer in those wrapping materials were not changed by #gamma#-irradiation. (M.N.)

1999-02-01

455

Ceramic Materials and Devices  

Science.gov (United States)

Course website from Cambridge on ceramic materials. This site contains eight lectures in PDF format (Adobe Reader required), two question sheets, five practicals (including answers), digital movies and further useful links. "There is a strong relationship between the structure of a material and its physical properties. The properties of a material whether mechanical, electrical, optical or magnetic, determine how it can be used in practical applications. In this course, the focus is on the structure / property relationship for ionic materials with electrical properties utilised in various transducer devices. The materials considered include perovskites, which have special polarisation properties exploited in ferroelectric, pyroelectric and piezoelectric devices. Other oxides, such as zirconia, have structures permitting rapid diffusion of ions, making them suitable for use in sensors, fuel cells and batteries. The scientific principles underlying the properties of ...

2007-02-01

456

Bragg Curve Counter for primary beam monitor  

Energy Technology Data Exchange (ETDEWEB)

The prototype Bragg Curve Counter (BCC) has been tested by {alpha}-source ({sup 241}Am) with a continuous gas flow system (P-10: 90% Ar+10% CH{sub 4}, at 300Torr). Two types of the Frisch grid were prepared for the BCC. One was made of expanded metal meshes, which consist of 175 meshes/inch{sup 2} with a 100{mu}m{sup t} nickel sheet. The other was made of a 1mm pitch wire with {phi} 50 {mu}m of the tungsten. The shape of Bragg peak signal was compared each other. It was found that the energy spectrum obtained by the wire grid is a little sharper than that obtained by the meshes grid. However the meshes grid is superior than the wire grid so far as handling and durability are concerned. (author).

1994-12-31

457

BOUNDARY LAYER FLOW AND DOUBLE DIFFUSION OVER AN UNSTEADY STRETCHING SURFACE WITH HALL EFFECT  

British Library Electronic Table of Contents (United Kingdom)

The present investigation is concerned with the effect of Hall currents on boundary layer flow, and heat and mass transfer of an electrically conducting fluid over an unsteady stretching sheet in the presence of a strong magnetic field. The electron-atom collision frequency is assumed to be relatively high, so that the Hall effect is assumed to exist, while the induced magnetic field is neglected. The governing time-dependent boundary layer equations for momentum, thermal energy, and concentration are reduced using a similarity transformation to a set of coupled ordinary differential equations. The similarity ordinary differential equations are then solved numerically by the successive linearization method together with the Chebyshev pseudo-spectral collocation method. Effects of the Prand...

2011-01-01

458

Assessment of degradation processes in corrosion resistant steels in nuclear power engineering  

International Nuclear Information System (INIS)

The possible corrosion damage is discussed of the CrNi and CrNiMo types steels used as structural materials in WWER type nuclear power plants. It includes point and slot corrosion, corrosion cracking and corrosion fatigue as well as corrosion denting. Also discussed are test procedures that simulate operating conditions and are used for assessing the properties of metallurgical products (sheets and tubes) used in nuclear power engineering. Briefly described is a system for testing the said products in an aqueous medium while keeping the test parameters in a narrow range for a long time. Under the defined temperature, pressure and corrosion medium composition, the test specimens in this system can mechanically be loaded, both statically and dynamically or a temperature gradient can be produced at the tube-tube plate joint. (Z.M.). 1 fig., 1 tab., 10 refs.

1987-12-01

459

Aquaculture of Uranium in Seawater by a Fabric-Adsorbent Submerged System  

Science.gov (United States)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m{sup 3} in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m{sup 2} in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

2003-11-15

460

Aquaculture of Uranium in Seawater by a Fabric-Adsorbent Submerged System  

International Nuclear Information System (INIS)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m3 in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m2 in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

2003-11-01

461

Anisotropic properties of magnesium sheet AZ31  

Energy Technology Data Exchange (ETDEWEB)

Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, r-values and their relation to the texture. This correlation between microstructure ...

2003-07-01

462

Alloy 800 specifications in compliance with component requirements  

Energy Technology Data Exchange (ETDEWEB)

In view of the importance of the material Alloy 800 in high-temperature reactor plants (HTR), a material data bank was established which is used for statistical evaluation of mechanical and physical material behaviour. Based on investigations on the interconnection between the mechanical properties at high temperatures and the metallurgical parameters, different types of Alloy 800 were specified in compliance with the component requirements. In addition, aspects of corrosion and toughness behaviour were taken into consideration. The specifications and strength characteristics for the different variants of Alloy 800 were incorporated into draft DIN standards after discussion and approval in expert committees. Further important characteristics of the mechanical and physical material behaviour were summarized in HTR material data sheets so as to furnish an improved basis for the design and stress analyses of Alloy 800 components. (orig.).

1990-04-01

463

Alloy 800 specifications in compliance with component requirements  

International Nuclear Information System (INIS)

In view of the importance of the material Alloy 800 in high-temperature reactor plants (HTR), a material data bank was established which is used for statistical evaluation of mechanical and physical material behaviour. Based on investigations on the interconnection between the mechanical properties at high temperatures and the metallurgical parameters, different types of Alloy 800 were specified in compliance with the component requirements. In addition, aspects of corrosion and toughness behaviour were taken into consideration. The specifications and strength characteristics for the different variants of Alloy 800 were incorporated into draft DIN standards after discussion and approval in expert committees. Further important characteristics of the mechanical and physical material behaviour were summarized in HTR material data sheets so as to furnish an improved basis for the design and stress analyses of Alloy 800 components. (orig.).

464

Advanced experimental design applied to damage tolerance of composite materials  

Science.gov (United States)

This paper focuses on a factorial-based design strategy. The approach provides an efficient and statistically reliable means for assessing the influence of multivariable effects. It is applied to the detection and evaluation of damage in impacted composite sandwich panels. The experimental results obtained from this test strategy are utilized to form an empirical response function. The resulting polynomial relates damage area to residual compression strength at values of independent variables for which testing did not occur. The response function also identifies nonlinear interaction effects of key variabes that cannot be easily ascertained by traditional single-variable test strategies. Independent variables evaluated include core thickness, number of face sheet plys and impact energy. The methodology presented allows the designer to predict with more confidence the damage tolerance of a composite material component, and the analyst to more accurately assess the ...

1991-01-01

465

A study on effects of parameters in the Lagrangian code based on F.E.M. through oblique dual-plates perforation phenomena  

International Nuclear Information System (INIS)

This study is concerned to the perforation phenomena of the oblique dual-plate by projectile. Experiment and simulation related to that was carried out. the variables considered in this phenomena include the electrolytic zinc coated steel sheet and carbon steel rod. In the former, the confirmation and projectile velocity possible phenomena of real phenomena is done, the latter, the effect of parameter such as time-step and grid space length is analyzed by using the three-dimensional Lagrangian explicit time-integration finite element code, HEMP. This code use the eight node hexahedral elements and in this study, Von-Mises Criteria is used as the strength model, Mie-Gruneisen is as the Equation of State. The simulation was performed by contrast with the experiment. Through the calibration of the parameter of Lagrangian code, reasonable result was approached.

2004-11-03

466

A micro-alloyed ferritic steel strengthened by nanoscale precipitates  

British Library Electronic Table of Contents (United Kingdom)

A ferritic steel with finely dispersed precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersed TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation ...

2011-01-01

467

A comparative assessment of slope stability of New Orleans I-wall with partial gap between the wall and layered cohesive backfill  

British Library Electronic Table of Contents (United Kingdom)

Following Hurricane Katrina, the study of cantilevered sheet pile I-wall with gap or partial gap has become one of the central elements of the ongoing investigation pertaining to the re-building of hurricane protection systems in New Orleans, LA. Historically, the US Army Corps of Engineers (USACE) had mostly relied upon the Method of Planes (MOP) analysis procedure for slope stability analysis of I-wall systems. However MOP is a simplified procedure which does not satisfy total equilibrium. Nevertheless, MOP is still considered by USACE as a popular analysis tool because of its simplicity and ease of use in slope stability analysis. This paper demonstrates the applicability and suitability of MOP as a viable analysis tool for the analysis of New Orleans I-wall founded on layered cohesive ...

2011-01-01

468

Study of the outgassing behavior of SnO_2:F films on glass in vacuum under external energy excitation  

International Nuclear Information System (INIS)

Vacuum glazing consists of an evacuated space between two sheets of glass. Vacuum glazing has a large effect on energy savings in houses and buildings. Vacuum glazing can achieve higher insulating performance than conventional insulated glazing. Nippon Sheet Glass has successfully developed conventional vacuum glazing. In this study we investigated an advanced form of vacuum glazing. Its thermal insulation ability is equivalent to 100 mm thick glass wool thermal insulation. This vacuum glazing contained a SnO_2:F low emissivity surface. The influence of the residual gas in a vacuum space on heat flow is important to performance. For long-term thermal stability, it is very important to maintain vacuum stability. To understand this better, we studied the behavior of outgassing from the inside glass surfaces exposed to an external energy source. We have studied the behavior of outgassing from a glass surface using a Nd:YAG laser (operated at 355 ...

2005-06-15

469

Steam Generator Group Project: Annual report, 1985  

Energy Technology Data Exchange (ETDEWEB)

This report is a summary of the Steam Generator Group Project progress for 1985. Statistical analyses are presented of data from nondestructive examination (NDE) round robin tests that were performed on the Surry generator in 1984. In the first round robin, teams acquired and analyzed their own data on a selected 10% subset of tubes. In the second round robin, analysts from each participating team analyzed identical sets of data which were provided to them by the Project. Results from several examinations utilizing advanced/alternate NDE technologies including alternate eddy current probes and techniques, ultrasonics, and profilometry are also reported. Criteria are listed for selecting tube specimens that will be removed from the generator. A sampling plan based on these criteria is detailed graphically in the report. The initial steps that have been taken to carry out the plan are described; tooling fabricated for the sample removals is discussed. Successful removal of three 9-tube ...

1987-04-01

470

Steam Generator Group Project: Annual report, 1985  

International Nuclear Information System (INIS)

This report is a summary of the Steam Generator Group Project progress for 1985. Statistical analyses are presented of data from nondestructive examination (NDE) round robin tests that were performed on the Surry generator in 1984. In the first round robin, teams acquired and analyzed their own data on a selected 10% subset of tubes. In the second round robin, analysts from each participating team analyzed identical sets of data which were provided to them by the Project. Results from several examinations utilizing advanced/alternate NDE technologies including alternate eddy current probes and techniques, ultrasonics, and profilometry are also reported. Criteria are listed for selecting tube specimens that will be removed from the generator. A sampling plan based on these criteria is detailed graphically in the report. The initial steps that have been taken to carry out the plan are described; tooling fabricated for the sample removals is discussed. Successful removal of three 9-tube ...

471

Si and Si/P implants in In{sub 0.5}Ga{sub 0.5}P and In{sub 0.5}Al{sub 0.5}P  

Science.gov (United States)

Si and Si/P ion implantation doping of In{sub 0.5}Ga{sub 0.5}P and In{sub 0.5}Al{sub 0.5}P has been studied for several Si and P doses at energies of 90 and 100 keV, respectively. For single Si implants in InGaP a maximum Hall sheet electron concentration of 1.33{times}10{sup 13} cm{sup {minus}2} is achieved for a Si dose of 5{times}10{sup 13} cm{sup {minus}2}. When an optimum dose (2.5{times}10{sup 13} cm{sup {minus}2}) P coimplant is performed this electron concentration is increased by 65{percent}. The same dose Si implants in InAlP show a maximum effective activation of 3.9{percent} with no P coimplantation and 5.2{percent} with a P-implant dose 1.5 times the silicon dose. The apparent donor ionization energies are estimated from variable temperature Hall measurements to be 2{endash}5 meV for InGaP and {approximately}80 meV for InAlP. The deeper level in InAlP is attributed to the DX level found in the Al-containing material. The reduction in ...

1996-06-01

472

PFB Coal Fired Combined Cycle Development Program: turbine materials evaluation, March 1980  

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of cladding technology development under the Coal-Fired Combined Cycle DOE Project. Clad Alloy Development, involved the selection, fabrication and burner rig evaluation of advanced clad alloy composition diffusion-bonded to IN-738. Testing was conducted for up to 5800 hours at 1600/sup 0/F in a simulated PFB environment. Metallographic evaluation showed Co-base cladding alloys PFB-5PM and PFB-6PM (aluminided) and Fe-base alloy GE-2541 to be the most corrosion resistant. The formability and fabricability of sheet material was significantly improved for these alloys by utilizing powder metallurgy techniques. Clad Process Development encompassed processing activities to evaluate sheet alloy formability, bucket surface preparation techniques, platform clad forming, and the activated diffusion bonding (ADB) of corrosion resistant tips to MS5001 buckets. The main focus, however, involved comprehensive evaluation of ...

1980-03-01

473

PFB Coal Fired Combined Cycle Development Program: turbine materials evaluation, March 1980  

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of cladding technology development under the Coal-Fired Combined Cycle DOE Project for the period July 1976 through June 1978. Sub-task 3.1, Clad Alloy Development, involved the selection, fabrication and burner rig evaluation of advanced clad alloy compositions diffusion-bonded to IN-738. Testing was conducted for up to 5800 hours at 1600/sup 0/F in a simulated PFB environment. Metallographic evaluation showed Co-base cladding alloys PFB-5PM and PFB-6PM (aluminided) and Fe-base alloy GE-2541 to be the most corrosion resistant. The formability and fabricability of sheet material was significantly improved for these alloys by utilizing powder metallurgy techniques. Sub-task 3.2, Clad Process Development, encompassed processing activities to evaluate sheet alloy formability, bucket surface preparation techniques, platform clad forming, and the activated diffusion bonding (ADB) of corrosion resistant tips to MS5001 ...

1980-03-01

474

Light-weight free-standing carbon nanotube-silicon films for anodes of lithium ion batteries.  

Science.gov (United States)

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network functions as both mechanical support and ...

2010-07-27

475

Formation of silk fibroin nanoparticles in water-miscible organic solvent and their characterization  

Energy Technology Data Exchange (ETDEWEB)

When Silk fibre derived from Bombyx mori, a native biopolymer, was dissolved in highly concentrated neutral salts such as CaCl{sub 2}, the regenerated liquid silk, a gradually degraded peptide mixture of silk fibroin, could be obtained. The silk fibroin nanoparticles were prepared rapidly from the liquid silk by using water-miscible protonic and polar aprotonic organic solvents. The nanoparticles are insoluble but well dispersed and stable in aqueous solution and are globular particles with a range of 35-125 nm in diameter by means of TEM, SEM, AFM and laser sizer. Over one half of the {epsilon}-amino groups exist around the protein nanoparticles by using a trinitrobenzenesulfonic acid (TNBS) method. Raman spectra shows the tyrosine residues on the surface of the globules are more exposed than those on native silk fibers. The crystalline polymorph and conformation transition of the silk nanoparticles from random-coil and {alpha}-helix form (Silk I) into anti-parallel ...

2007-10-15

476

The radioecological risk of decommissioning of nuclear submarines. Possible accidents and normal conditions  

International Nuclear Information System (INIS)

In the report the results of the estimations of radiological risk of various stages of decommissioning of nuclear submarines are presented. At occurrence on nuclear submarine the heavy failure, relating to the class hypotetical volume of acting of radionuclides in atmosphere can reach 1.6E(15) Bq. Results of estimations probable doses on an axis of a trace of a radioactive loop show, that at distribution of radionuclides during atmospheric carry to 'agreed' settlement (500-1000 m) the maximum doses on its territory can make: about 6.0E(-3) Sv (for the whole body); 3.0E(-3) Gy for the leather (basal layer); 6.3E(-2) Gy for the lungs (acute exposure) and up to 1.8 Gy for the thyroid gland. Hypotetical failure for the estimation of the greatest possible radioecological consequences for hydrobiocenosis is considering, connected with single discharge of liquid radioactive waste (LRW) in water area. At navigating failure of the tanker with LRW in water area can arrive 300 M3 of LRW with the ...

2000-05-01

477

Yield-increasing additives in kraft pulping: Effect on carbohydrate retention, composition and handsheet properties  

Energy Technology Data Exchange (ETDEWEB)

In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the ...

2008-07-01

478

UNSAT-H Version 3.0: Unsaturated Soil Water and Heat Flow Model Theory, User Manual, and Examples  

Energy Technology Data Exchange (ETDEWEB)

The UNSAT-H model was developed at Pacific Northwest National Laboratory (PNNL) to assess the water dynamics of arid sites and, in particular, estimate recharge fluxes for scenarios pertinent to waste disposal facilities. During the last 4 years, the UNSAT-H model received support from the Immobilized Waste Program (IWP) of the Hanford Site's River Protection Project. This program is designing and assessing the performance of on-site disposal facilities to receive radioactive wastes that are currently stored in single- and double-shell tanks at the Hanford Site (LMHC 1999). The IWP is interested in estimates of recharge rates for current conditions and long-term scenarios involving the vadose zone disposal of tank wastes. Simulation modeling with UNSAT-H is one of the methods being used to provide those estimates (e.g., Rockhold et al. 1995; Fayer et al. 1999). To achieve the above goals for assessing water dynamics and estimating recharge rates, the UNSAT-H model addresses ...

2000-06-12

479

Surface expressions of subsurface structures in parts of the Michigan and Illinois basins  

Energy Technology Data Exchange (ETDEWEB)

Study of glacial geology, stream drainage, bedrock topography, and subsurface structure maps in Isabella, Midland, Arenac, Gladwin, Clare, Ogemaw, Iosco, Mecosta, and Montcalm counties in Michigan revealed distinct correlations between patterns and types of glacial deposits and subsurface structures. Anticlinal structures associated with the Mt. Pleasant, North Buckeye, and South Buckeye, Hamilton, Deep River, Clayton, Logan, Six Lakes, and West Branch oil and gas fields occur along areas where northeast-trending glacial moraines and truncated, attenuated, or deviated. Furthermore, these anticlinal structures are associated with lacustrine sands and gravels and glacial outwash deposits nearly surrounded by glacial tills or lacustrine sands and clays. All of the anticlinal structures are associated with bedrock topography highs and alignment of streams parallel to the trends of the structures. Comparison of images of subsurface structure and surface elevation data ...

1991-08-01

480

Quaternary tilt of Death Valley determined from landform modelling of alluvial fans  

Energy Technology Data Exchange (ETDEWEB)

Alluvial fans along the east side of central Death Valley are being actively back-tilted along the Death Valley fault zone. Initial modelling of the Copper Canyon and Furnace Creek fans led to recognition of distinct segments. Field reconnaissance and aerial photo mapping were conducted to check model results and improve segment discrimination. Surface roughness, relative position, vegetation distribution, and drainage patterns provided independent evidence for segment discrimination. Subsequent modelling of individual segments produced a range of tilt values from 0.275[degree] to 0.559[degree] down to the northeast. Continued analysis of these fan segments is concentrated on: (1) assigning confidence and error values to the tilt values; and (2) dating individual segments. Further work will compare the tilt rates of east-side fans with those from the west. The mean squared error (MSE) is currently being used as a first order assessment of the quality of the ...

1993-04-01

481

Proceedings of GeoEdmonton 2008 : the 61. Canadian geotechnical conference and 9. joint CGS/IAH-CNC groundwater conference : a heritage of innovation  

Energy Technology Data Exchange (ETDEWEB)

This conference provided a forum for more than 500 delegates from industry, government universities and research centres to share their professional knowledge on research and development that affects all sectors of geotechnical engineering, applied geology and hydrogeology. Accomplishments in the geoenvironmental field were also highlighted. The geotechnical sessions were entitled: pile foundations and load testing; excavations and special foundation issues; reinforced soil and soil-structure interactions; advances in modelling, constitutive issues; advances in modelling, consolidation and other applications; advances in modelling, discrete elements and slope stability; embankments and dams; landfills and barriers; fundamental soil mechanics; soil mechanics and ground movement; GIS and remote sensing; landslides and slopes; cone penetration tests and liquefaction assessment; rock mechanics; engineering geology; geoenvironmental sustainability; oilsand and petroleum geomechanics; and, ...

2008-07-01

482

Preoperative assessment of hilar cholangiocarcinoma using multidetector-row CT. Correlation with histopathological findings  

International Nuclear Information System (INIS)

Our aim was to investigate the diagnostic reliability of multidetector-row computed tomography (MDCT) for preoperative assessment of local tumoral spread in hilar cholangiocarcinoma. Thirteen of 30 consecutive patients with hilar cholangiocarcinoma who underwent surgery, excluding 17 patients who underwent biliary drainage or preoperative portal embolization, were retrospectively evaluated. Using MDCT systems of 4 detector rows or 16 detector rows, plain and dynamic contrast-enhanced images of three phases were obtained. Extent of tumor spread and lymph node metastasis were assessed with MDCT and compared with histopathological findings. The Bismuth-Corlette classification of hilar cholangiocarcinoma with MDCT were type I, 1 patient; type IIIa, 3 patients; type IIIb, 4 patients; and type IV, 5 patients; those with histopathological findings were type I, 1 patient; type IIIa, 2 patients; type IIIb, 4 patients; and type IV, 6 patients. One patient diagnosed as type ...

2008-08-01

483

Operational experiences with cathodic protection of Statoil's main onshore pipelines: a description of the online monitoring systems  

Energy Technology Data Exchange (ETDEWEB)

Statoil is operating an increasing number of offshore and onshore pipelines in the North Sea area and elsewhere. Cathodic protection is a significant part of the corrosion management for these lines and we have collected a significant amount of experience with respect to design and operation of the systems. This paper deals with our comprehensive program for the onshore cathodic protection systems and the various challenges in different countries with respect to technical matters, such as operating conditions and different terrain. Generally, the systems are based on automatically controlled rectifier systems with a wide range of current drainage and very comprehensive monitoring of potentials and current flowing. The use of coupons, polarisation cells and buried reference cells are essential, as well as the use of intensive measurements along the route. The use of online monitoring of selected test posts and all rectifier units is considered essential for remote ...

1999-07-01

484

Mucociliary transport and upper airway disease  

International Nuclear Information System (INIS)

Mucociliary transport so critical in nasal, paranasal sinus, and middle ear physiology is impaired in chronic sinsusitis and otitis media by factors such as increased mucus viscoelasticity, decreased ciliary area, and primary or secondary ciliary immotility. We reviewed the pathophysiology of primary ciliary dyskinesia, otitis media with effusion, chronic sinusitis, and allergic rhinitis in terms of mucociliary transport. Subjects with primary ciliary dyskinesia may experience recurrent middle ear infection, chronic airway infection, predominantly lower-lobe bronchiectasis, male sterility, or situs inversus. Primary ciliary dyskinesia is sometimes difficult to diagnose in cases without situs inversus. Nasal nitric oxide concentration in such patients decreases, although why is unclear. Mutations may involve dynein arm intermediate chain 1 (DNAI1) or dynein arm heavy chain 5 (DNAH5). Mucociliary clearance decreases more in those with otitis media with effusion than in those without, due ...

2010-05-01

485

Method for predicting diffusion of discharged warm water in the regions of coastal sea  

International Nuclear Information System (INIS)

The present situation of the researches that have been made for predicting the process and range of diffusion of warm drain is reviewed. This review is divided into eight sections. The first section deals with the present situation of warm drain from power plants. For the establishment of drainage standard, there are many difficult problems to be solved because water temperature differs in its nature from other regulation items. In the second section, the process of diffusion and cooling of warm drain is explained. The third section deals with the diffusion characteristics of warm drain in Japanese coastal sea due to water temperature. Two types of diffusion are known. One is dominant irregular current, and the other is periodical reciprocating stream. The fourth section deals with the methods of prediction of diffusion. Research methods and simulation models are described. The fifth section deals with the prediction with single layer model. Fundamental ...

1975-01-01

486

Engineering masterpieces : from the Andes to Siberia, Canadian talent is in demand  

Energy Technology Data Exchange (ETDEWEB)

Canadian oilfields are a prime breeding ground for talent, technology and industrial management. This paper described how Canadian talent was recognized in 2001 for three major projects which included a cold-ocean production platform in the Sea of Okhotsk in Siberia, a mountain pipeline project in South America, and an in-situ underground extraction technology in the oilsands of Alberta. The cold-ocean production platform project was recruited by Sakhalin Energy Investment Co., an international consortium originally led by Marathon Oil Co which is now led by Royal Dutch Shell. The oil production platform is stationed 16 kilometres offshore of Sakhalin Island in the Sea of Okhotsk. Sakhalin Energy bought and converted the Molikpaq, an innovative platform made in the 1980s for the Beaufort Sea by Gulf Canada Resources Ltd. The second project included Calgary's Hydroconsult EN3 Services Ltd. which was responsible for the construction of the 940-km GasAtacama 24-inch diameter ...

2001-03-05

487

Effects of pH and phosphate on metal distribution with emphasis on As speciation and mobilization in soils from a lead smelting site  

Energy Technology Data Exchange (ETDEWEB)

Arsenic in soils from the Asarco lead smelter in East Helena, Montana was characterized by X-ray absorption spectroscopy (XAS). Arsenic oxidation state and geochemical speciation were analyzed as a function of depth (two sampling sites) and surface distribution. These results were compared with intensive desorption/dissolution experiments performed in a pH stat reactor for samples from the site with the highest degree of As heterogeneity. The objectives of the study were to investigate the solid-phase geochemical As speciation, assess the speciation of As in solutions equilibrated with the solids under controlled pH (pH=4 or 6) and Eh (using hydrogen or air) environments, observe the effects of phosphate on the release of As into solution, and examine the effects of phosphate on metal mobility in the systems. Arsenic was predominantly found in the As(V) valence state, though there was evidence that As(III) and As(0) were present also. The dominant geochemical phase was scorodite ...

2005-06-01

488

Coupled modeling of non-isothermal multiphase flow, solutetransport and reactive chemistry in porous and fractured media: 1. ModelDevelopment and Validation  

Energy Technology Data Exchange (ETDEWEB)

Coupled modeling of subsurface multiphase fluid and heat flow, solute transport and chemical reactions can be used for the assessment of acid mine drainage remediation, mineral deposition, waste disposal sites, hydrothermal convection, contaminant transport, and groundwater quality. Here they present a numerical simulation model, TOUGHREACT, which considers non-isothermal multi-component chemical transport in both liquid and gas phases. A wide range of subsurface thermo-physical-chemical processes is considered. The model can be applied to one-, two- or three-dimensional porous and fractured media with physical and chemical heterogeneity. The model can accommodate any number of chemical species present in liquid, gas and solid phases. A variety of equilibrium chemical reactions is considered, such as aqueous complexation, gas dissolution/exsolution, cation exchange, and surface complexation. Mineral dissolution/precipitation can proceed either subject to local ...

1998-09-01

489

Climate change, agriculture and wetlands in Eastern Europe: vulnerability, adaptation and policy  

Energy Technology Data Exchange (ETDEWEB)

Naturally-occurring wetlands perform such functions as flood control, pollution filtration, nutrient recycling, sediment accretion, groundwater recharge and water supply, erosion control, and plant and wildlife preservation. A large concentration of wetlands is located in Eastern Europe. A significant amount of Eastern European wetlands has been converted to agricultural use in the past, and remaining wetlands are subject to agricultural drainage. Drained wetlands are used as prime agriculture lands for a variety of food crops. Other agricultural uses of wetlands range from growing Phragmites australis (common reed) for thatch and livestock feed, to collecting peat for heating and cooking fuel. Altered hydrologic regimes due to global climate change could further exacerbate encroachment of agricultural land use into wetlands. The vulnerability and adaptation studies of the US Country Studies Program are used to analyze where climate change impacts to agriculture ...

1997-05-01

490

City of Seattle green roof policy development through extended performance monitoring as a basis for hydrologic modeling  

Energy Technology Data Exchange (ETDEWEB)

The advantages offered by green roofs range from improvement in architectural and landscape aesthetics to reductions in building energy costs. Seattle Public Utilities (SPU) is encouraging sustainable community development through new policies and regulations that promote green roof installation on public and commercial rooftops in Seattle's urban center. An understanding of climate-specific green roof performance is required in order to develop an accurate representation of the stormwater benefits of green roofs. This paper explored the relative importance of green roofs in storm water management and low impact development (LID) in various areas of Seattle. It also examined the relative effectiveness and applicability of green roofs under various conditions and in various parts of the city compared to other LID strategies such as Seattle's natural drainage systems (NDS) designs, swales and ponds, rain gardens, rainwater harvesting, and porous ...

2007-07-01

491

Change in runoff characteristics of alpine flowing waters caused by the use of hydroelectric power and its effects on the macro-benthos  

International Nuclear Information System (INIS)

A typical form of change in runoff characteristics caused by the widespread use of hydroelectric power in Switzerland is the intermittent draining (torrent operation). It is the aim of the present work to help elucidate possible consequences of these changes in drain onto the benthobiocoenosis. The study was carried through on the Secklisbach at Oberrickenbach (in the semicanton of Nidwalden) and one of its side streamlets (800m above sea level). The macroinvertebrate coenosis was studied at four locations with similar conditions of drainage basin, population density and topography but varying in the degree of impairment to the draining. There were monthly benthos samples taken using a Surber sampling-device. Results show that the locations not only varied in drain, but also in temperature, this being a consequence of water storage by the power plant. The readings pointed out different values for the locations in daily average temperature, day amplitudes and ...

492

Archive monitoring of pollutants in the Dee River using SIMS analysis of mussels  

International Nuclear Information System (INIS)

Full text: Mt Morgan was mined for copper and gold from 1882 to 1982 and subsequent tailings re-processing ceased in 1990. Direct and accidental deposition of tailings into the adjacent Dee River and acid mine drainage from the mine site continues to impact the Dee River. The Queensland Department of Natural Resources gauging and monitoring station at Kenbula (adjacent to the mine) continuously monitors pH of around 2.8. Twenty kilometres downstream of the mine the pH improves to 3.5. Elevated sediment metal concentrations have been recorded over 50 kilometres downstream in investigations conducted by CSIRO (Jones et al. 1995, 1996) and others. Biological monitoring by Mackey (1988) and subsequently by Duivendoorden (1995,1997), confirmed significant impact on the fish, macrophyte of macro invertebrate populations downstream of the mine. The current AINSE sponsored project will investigate the use of mussels (genus Allathryia) to archive the pollutant load in the ...

2000-11-29

493

The earth is warming up while the sky is getting a chill; La terre se rechauffe, le ciel a un coup de froid  

Energy Technology Data Exchange (ETDEWEB)

The phenomenon of global warming, its causes and implications for the future, and the relationship between global warming and the depletion of the ozone layer are discussed. The Shindell model of the greenhouse effect, which is responsible for planetary warming, also contributes to the high altitude thinning of the ozone layer. While greenhouse gas emissions contribute to retaining infrared radiation, thus warming the surface of the earth, their effect is reduced at stratospheric altitudes resulting in reduced temperatures in this region. At this altitude temperatures can reach minus 90 degrees C, creating a whirlwind effect, with ice crystals forming at the heart of the vortex, causing the surface to accelerate chemical reactions which in turn leads to destruction of ozone. Although since the signing of the Montreal Protocol in 1987 the industrialized countries have significantly reduced their emissions of refrigerating gas (chlorofluorocarbons or CFC), which were ...

2001-03-01

494

SUBMILLIMETER ARRAY OBSERVATIONS TOWARD THE MASSIVE STAR-FORMING CORE MM1 OF W75N  

International Nuclear Information System (INIS)

The massive star-forming core MM1 of W75N was observed using the Submillimeter Array with #approx#1'' and 2'' spatial resolutions at 217 and 347 GHz, respectively. From the 217 GHz continuum we found that the MM1 core consists of two sources, separated by about 1'': MM1a (#approx#0.6 M_s_u_n) and MM1b (#approx#1.4 M_s_u_n), located near the radio continuum sources VLA 2/VLA 3 and VLA 1, respectively. Within MM1b, two gas clumps were found to be expanding away from VLA 1 at about #+-#3 km s"-"1, as a result of the most recent star formation activity in the region. Observed molecular lines show emission peaks at two positions, MM1a and MM1b: sulfur-bearing species have emission peaks toward MM1a, but methanol and saturated species at MM1b. We identified high-temperature (#approx#200 K) gas toward MM1a and the hot core in MM1b. This segregation may result from the evolution of the massive star-forming core. In the very early phase of star formation, the hot core is seen through the ...

2010-11-10

495

Mercury and other trace elements in a pelagic Arctic marine food web (Northwater Polynya, Baffin Bay)  

Energy Technology Data Exchange (ETDEWEB)

Total mercury (THg), methylmercury (MeHg) and 22 other trace elements were measured in ice algae, three species of zooplankton, mixed zooplankton samples, Arctic cod (Boreogadus saida), ringed seals (Phoca hispida) and eight species of seabirds to examine the trophodynamics of these metals in an Arctic marine food web. All samples were collected in 1998 in the Northwater Polynya (NOW) located between Ellesmere Island and Greenland in Baffin Bay. THg and MeHg were found to biomagnify through the NOW food web, based on significant positive relationships between log THg and log MeHg concentrations vs. {delta} {sup 15}N muscle and liver . The slope of these relationships for muscle THg and MeHg concentrations (slope = 0.197 and 0.223, respectively) were similar to those reported for other aquatic food webs. The food web behavior of THg and {delta} {sup 15}N appears constant, regardless of trophic state (eutrophic vs. oligotrophic), latitude (Arctic vs. tropical) or ...

2005-12-01

496

Mercury and other trace elements in a pelagic Arctic marine food web (Northwater Polynya, Baffin Bay)  

International Nuclear Information System (INIS)

Total mercury (THg), methylmercury (MeHg) and 22 other trace elements were measured in ice algae, three species of zooplankton, mixed zooplankton samples, Arctic cod (Boreogadus saida), ringed seals (Phoca hispida) and eight species of seabirds to examine the trophodynamics of these metals in an Arctic marine food web. All samples were collected in 1998 in the Northwater Polynya (NOW) located between Ellesmere Island and Greenland in Baffin Bay. THg and MeHg were found to biomagnify through the NOW food web, based on significant positive relationships between log THg and log MeHg concentrations vs. #delta# "1"5N muscle and liver . The slope of these relationships for muscle THg and MeHg concentrations (slope = 0.197 and 0.223, respectively) were similar to those reported for other aquatic food webs. The food web behavior of THg and #delta# "1"5N appears constant, regardless of trophic state (eutrophic vs. oligotrophic), latitude (Arctic vs. tropical) or salinity ...

2005-12-01

497

Ground- and space-based temperature and humidity retrievals: Statistical evaluation  

Energy Technology Data Exchange (ETDEWEB)

A near-real-time integrated temperature and water vapor sounding system has been designed and in operation since June 1993. It combines hourly data from the ground-based radio acoustic sounding system (RASS), a two-channel microwave radiometer, standard surface meteorological instruments, a lidar ceilometer, and the Aerodynamic Research Incorporated Communication, Addressing and Reporting System aboard commercial airlines with space-based data from the TIROS-N Operational Vertical Sounder (TOVS). The physical retrieval algorithm provided by the International TOVS Processing Package is used for combining the ground- and space-based temperature and humidity profiles. The first-guess profiles of temperature and humidity required by the physical retrieval algorithm are obtained by using a statistical inversion technique and the ground-based remote sensors measurements. Statistical error estimates are presented for the hourly, near-real-time, ground-, and space-based retrieved temperature ...

1996-03-01

498

Glacier changes in the Siberian Altai Mountains, Ob river basin (1952-2006) estimated with high resolution imagery  

Energy Technology Data Exchange (ETDEWEB)

The Siberian Altai covers about 70% of the area of all south Siberian glaciers, which provide fresh water to the upper tributaries of the Ob and Yenisey rivers. The observed air temperature has increased by 1.2 deg. C over northern Eurasia during the last 120 years, affecting the degradation of the Siberian Altai glaciers. In this study, we estimated glacier area changes in the Aktru River basin (44.8 km{sup 2}), located in the central Altai mountains. We used the 1952, 1966, 1975 and 2006 remote sensed images with 0.6-3.0 m spatial resolution (aerial photographs, Corona and PRISM satellite images) and differential GPS (DGPS) data. From 1952 to 2006, the total glacier area in the Aktru basin shrank by 7.2% (1.2 km{sup 2}). During the last three decades, the rate of glacier area loss increased by a factor of 1.8, thus resembling trends in other mountain systems of Eurasia (Alps, Tien Shan). The glacier area changes were caused mainly by increase of summer air temperature by 1.03 deg. C ...

2007-10-15

499

Glacier changes in the Siberian Altai Mountains, Ob river basin (1952-2006) estimated with high resolution imagery  

International Nuclear Information System (INIS)

The Siberian Altai covers about 70% of the area of all south Siberian glaciers, which provide fresh water to the upper tributaries of the Ob and Yenisey rivers. The observed air temperature has increased by 1.2 deg. C over northern Eurasia during the last 120 years, affecting the degradation of the Siberian Altai glaciers. In this study, we estimated glacier area changes in the Aktru River basin (44.8 km"2), located in the central Altai mountains. We used the 1952, 1966, 1975 and 2006 remote sensed images with 0.6-3.0 m spatial resolution (aerial photographs, Corona and PRISM satellite images) and differential GPS (DGPS) data. From 1952 to 2006, the total glacier area in the Aktru basin shrank by 7.2% (1.2 km"2). During the last three decades, the rate of glacier area loss increased by a factor of 1.8, thus resembling trends in other mountain systems of Eurasia (Alps, Tien Shan). The glacier area changes were caused mainly by increase of summer air temperature by 1.03 deg. C (from 1951 ...

500

Extension of improved particle and energy confinement regime in the core of LHD plasma  

International Nuclear Information System (INIS)

Recent two major topics of Large Helical Device (LHD) towards fusion relevant conditions, high-density operation and high-ion-temperature operation, are reported. Super dense core plasma was obtained by the combination of repetitive hydrogen ice pellet injection and high power neutral beam injection (NBI) heating. A very peaked density profile with the highest central density of 1.1x1021 m-3 was produced showing that the particle transport was suppressed very well in the plasma core. The spatial density varies as the position of magnetic axis (Rax), and the steepest profile is obtained at Rax=3.95 m. The highest central ion temperature of 5.6 keV was obtained in hydrogen plasma at electron density of 1.6 x 1019 m-3 by NBI, where a peaked ion-temperature profile with internal ion energy transport barrier was observed. The profile of electron temperature did not change much and was broad even when the ion temperature had a peaked profile. The central ion temperature ...

2009-06-01