Energy Technology Data Exchange (ETDEWEB)

Commercial focused ion beam (FIB) systems are commonly used to image integrated circuits (ICS) after device processing, especially in failure analysis applications. FIB systems are also often employed to repair faults in metal lines for otherwise functioning ICS, and are being evaluated for applications in film deposition and nanofabrication. A problem that is often seen in FIB imaging and repair is that ICS can be damaged during the exposure process. This can result in degraded response or out-right circuit failure. Because FIB processes typically require the surface of an IC to be exposed to an intense beam of 30--50 keV Ga{sup +} ions, both charging and secondary radiation damage are potential concerns. In previous studies, both types of effects have been suggested as possible causes of device degradation, depending on the type of device ...

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A monolithic micromachined waveguide device or devices with low-loss, high-power handling, and near-optical frequency ranges is set forth. The waveguide and integrated devices are capable of transmitting near-optical frequencies due to optical-quality sidewall roughness. The device or devices are fabricated in parallel, may be mass produced using a LIGA manufacturing process, and may include a passive component such as a diplexer and/or an active capping layer capable of particularized signal processing of the waveforms propagated by the waveguide.

International Nuclear Information System (INIS)

A program was undertaken to radiation harden an existing power integrated circuit technology (BCDMOS) to total dose, gamma dot, SEU, and neutrons. Efforts have centered around hardening and optimizing our CMOS, DMOS, and NPN devices. Initial results indicate a substantial improvement in hardness over our existing commercial technology.

Energy Technology Data Exchange (ETDEWEB)

The plastic deformation behavior of formed CICC for the superconducting Tokamac fusion device was examined and appropriate manufacturing information was provided. A relation between travel of the bending roller and spring back displacement was obtained via virtual manufacturing. The radius of CICC after forming was expressed as a function of the bend-roll travel. The maximum von Mises stress after spring back was also monitored for the SAGBO prediction. Next, the variation of the CICC cross-sectional area was examined during the first turn and during conduit bending with the largest curvature. Finally, the coil radius was measured and compared with the data generated from the virtual manufacturing. The measured data showed similar pattern as predicted one. Using the mapping function found to match with the real data, the data from the virtual manufacturing may facilitate accurate ...

Science.gov (United States)

Jul 16, 2005 ... The purpose of this capability portfolio is to develop a roadmap for NASA to exploit .... 1.2.4-2: Some applications of nanotechnology to advanced EVA suits. ..... Power/Energy Storage: Materials and devices for energy storage and .... to 80 %), manufacturing costs (up to 50%) and enhancements in durability. ...

Energy Technology Data Exchange (ETDEWEB)

Approximately 95% of the world`s integrated chips are packaged using a hot, high pressure transfer molding process. The stress created by the flow of silica powder loaded epoxy can displace the fine bonding wires and can even distort the metalization patterns under the protective chip passivation layer. In this study the authors developed a technique to measure the mechanical stress over the surface of an integrated circuit during the molding process. A CMOS test chip with 25 diffused resistor stress sensors was applied to a commercial lead frame. Both compression and shear stresses were measured at all 25 locations on the surface of the chip every 50 milliseconds during molding. These measurements have a fine time and stress resolution which should allow comparison with computer simulation of the molding process, thus allowing optimization of both the manufacturing process and mold geometry.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Discusses methods for determining ash content in coal using backscattering in X-ray fluorescence. The following aspects are evaluated: principle of ash content determination, energy sources, factors that influence measurement accuracy, reliability. Types of X-ray fluorescence analyzers developed in Czechoslovakia and manufactured in the Czech Republic are comparatively evaluated. Operation of the RPM 113.1 radionuclide X-ray fluorescence analyzer developed by the PAR company and used for measuring ash content in coal and coal calorific value is discussed. 7 refs.

British Library Electronic Table of Contents (United Kingdom)

The review provides a general idea about the types of metallic alloys and the pure metals used as implant materials in dental and orthopedic surgery. Their corrosive behavior in both real solutions and various media that model human biological fluids is described. Based on the literature data, it is concluded that multicomponent alloys containing titanium, niobium, zirconium, tungsten, molybdenum, aluminum, and silicon are the most resistant to corrosion. Implants made of different types of stainless steel are preferred when manufacturing orthopedic devices for short-term use.

CERN Document Server

The internal-tracking-system (ITS) of the ALICE detector at LHC, consists of six concentrical barrels of silicon detectors. The outmost two layers are made of double-sided strip detectors (SSD). In the framework of a R and D, the characteristics and performances of these devices, manufactured by two different companies, associated with their designed read-out electronics, have been studied off- and in-beam at the SPS (CERN). The results are presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this solar energy project was to design, manufacture, install, maintain and evaluate solar heating systems in order to stimulate community acceptance of the practicality of solar applications, reduce non-renewable energy resource consumption, and decrease residential expenditures for energy. The project also provided skill training and experience for CETA employees in the design, manufacture, and installation of solar energy equipment systems. CDC's contract had four separate solar energy projects; namely: Domestic Water Heating Systems for four Single-Family Homes; Domestic Water Heating for an industrial building; Domestic Water Heating for a (4) unit apartment complex (includes (12) supplemental space heating units); and Integral Passive Water Heaters and Energy Conservation Devices for (8) one bedroom homes. CDC staff designed all solar systems and CETA trainees (County and City vocational ...

International Nuclear Information System (INIS)

A heavy ion gas detector system consisting of a Bragg-curve spectroscopy ionization chamber for particle identification and a multiwire proportional chamber as position sensitive fast trigger device is described. The Bragg IC has been tested with several beams up to Z=36 to investigate some aspects of the BCS method. Results are reported on energy resolution and linearity, Z resolving power and mass sensitivity. The energy resolution is well below 1%. The Bragg-peak amplitude is fairly independent of the energy in a wide energy range and single elements are identified up to Z=38 with a resolving power Z/#DELTA#Zproportional50-80. Isotope identification by range measurement is limited by the straggling in the ionization process and the mass resolving power is M/#DELTA#Mproportional20-26 for S and Si isotopes. The MWPC allows subnanosecond time resolution and position identification along the in-plane coordinate within +-0.5 mm. (orig.).

UK PubMed Central (United Kingdom)

The cloned 135-kDa CryIC delta-endotoxin from Bacillus thuringiensis is a lepidopteran-active toxin, displaying high activity in vivo against Spodoptera litoralis and Spodoptera frugiperda larvae and...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

High-resolution near-infrared and far-infrared observations are presented of the southeastern molecular cloud fragment in the IC 5146 dark cloud. These observations rule out earlier suggestions for the formation of massive stars in this fragment.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.

British Library Electronic Table of Contents (United Kingdom)

In this work an experimental study is carried out to determine the thermo-hydraulic performance of an intercooler (IC) with flat tubes provided with triangular plain internal fins and louvered external fins when it is used on a car equipped with a low pressure EGR. The main unknowns to be answered are the thermo-hydraulic characteristics of the IC working under humid conditions induced by EGR, the conditions under which the water content in the mixture of air and exhaust gases begins to condense and the conditions under which the condensed water will be retained inside the IC. The exhaust gases are here replaced by a mixture of dry air and water vapour which are mixed upstream of the IC. The IC is submitted at the following testing conditions: on the ambient air side, the air temperature i...

British Library Electronic Table of Contents (United Kingdom)

In this study, a new type of thin, compact, and light weighed diaphragm micro-pump has been successfully developed to actuate liquid by the vibration of a diaphragm. The micro-diaphragm pump with two valves is fabricated in an aluminum case by using highly accurate CNC machine, and the cross-section dimension is 28?mm??5?mm. Both valves and diaphragm are manufactured from PDMS. The amplitude of vibration by a piezoelectric device produces an oscillating flow and alters the chamber volume by the curvature change of a diaphragm. Several experimental set-ups for performance tests in a single micro-diaphragm pump, isothermal flow open system, and a closed liquid cooling system are designed and implemented. The performance of a one-side actuating micro-diaphragm pump is affected by the design ...

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning plasma immersion ion implantation (PIII) and equipment. PIII is a new technique to implant plasma ions into materials for surface modification and treatment. Topics include plasma nitriding, semiconductor doping, ion energy distribution, ion dose, pulsed plasma, metal plasma, and defect passivation. References also review applications in semiconductor device and integrated circuit manufacture, silicon material fabrication, aerospace bearings, carbon coatings on metals, and ceramic coatings. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

Energy Technology Data Exchange (ETDEWEB)

Developments made under this program will play a key role in underpinning the technology for producing EC devices. It is anticipated that the work begun during this period will continue to improve materials properties, and drive yields up and costs down, increase durability and make manufacture simpler and more cost effective. It is hoped that this will contribute to a successful and profitable industry, which will help reduce energy consumption and improve comfort for building occupants worldwide. The first major task involved improvements to the materials used in the process. The improvements made as a result of the work done during this project have contributed to the enhanced performance, including dynamic range, uniformity and electrical characteristics. Another major objective of the project was to develop technology to improve yield, reduce cost, and facilitate manufacturing of EC products. Improvements directly ...

Science.gov (United States)

of the Intelligent Control System (ICS) for reusable rocket engines. .... the incoming measurements with corresponding estimates, a sensor failure can be ...

Science.gov (United States)

... qualified manufacturing employees. David Lichtinger, plant manager for Lord Corporation's aerospace products plant in ...

International Nuclear Information System (INIS)

Electrofuel Inc. develops, manufactures and sells a lithium ion superpolymer rechargeable battery technology. This unique and breakthrough technology provides the highest energy density and longest lasting portable power source on the market today. The company's goal is to become the leading provider of portable power for the portable computer and wireless sectors and to apply its technology to a wide range of alternative energy applications. The market for this technology is large and growing rapidly. Sales have increased from 190 million devices in 1998 to a projected 600 million in 2003. The increased sales are driven by better affordability, reduced size and functionality of the battery. This annual report highlights some of the major milestones the company achieved in 2000 which helped advance the corporate strategy and which marked its transformation from a late stage development company to an early stage commercial ...

Energy Technology Data Exchange (ETDEWEB)

Classical semiconductor physics has been continuously improving electronic components such as diodes, light-emitting diodes, solar cells and transistors based on highly purified inorganic crystals over the past decades. Organic semiconductors, notably polymeric, are a comparatively young field of research, the first light-emitting diode based on conjugated polymers having been demonstrated in 1990. Polymeric semiconductors are of tremendous interest for high-volume, low-cost manufacturing (''printed electronics''). Due to their rather simple device structure mostly comprising only one or two functional layers, polymeric diodes are much more difficult to optimize compared to small-molecular organic devices. Usually, functions such as charge injection and transport are handled by the same material which thus needs to be highly optimized. The present work contributes to expanding the ...

CERN Document Server

We present results of the search for Cepheids in the galaxy IC1613 carried out as a sub-project of the OGLE-II microlensing survey. 138 Cepheids were found in the 14.2x14.2 arcmin region in the center of the galaxy. We present light curves, VI photometry and basic data for all these objects, as well as color-magnitude diagram of the observed field. The Period--Luminosity (PL) diagrams for IC1613 fundamental mode Cepheids for VI and interstellar extinction insensitive index W_I are constructed. Comparison of PL relations in metal poor galaxy IC1613 ([Fe/H]~-1.0 dex) with relations in metal richer Magellanic Clouds allows us to study dependence of Cepheid PL relations on metallicity in the wide range of metallicities covered by these three galaxies. The slopes of PL relations in IC1613 are identical as in the Magellanic Clouds. The comparison of brightness of Cepheids with the magnitudes of the tip of the ...

Science.gov (United States)

The aim of present study was to evaluate antioxidant property of Glycyrrhiza glabra root extracts using in vitro models. The dose-dependent aqueous and ethanolic extracts demonstrated the scavenging activity against nitric oxide (concentration that caused 50% inhibition of nitric oxide radicals [IC(50)]=72 and 62.1 microg/ml, respectively), superoxide (IC(50)=64.2 and 38.4 microg/ml, respectively), hydroxyl (IC(50)=81.9 and 63 microg/ml, respectively), DPPH (IC(50)=43.6 and 28.3 microg/ml, respectively) and ABTS(*+) (IC(50)=77.3 and 57.2 microg/ml, respectively) radicals. Further, both extracts showed strong reducing power and iron-chelating capacities. In the Fe(2+)/ascorbate system, both extracts were found to inhibit mitochondrial fraction lipid peroxidation. In copper-catalyzed human serum and low-density lipoprotein oxidation models, both extracts significantly (P<0.05) ...

Energy Technology Data Exchange (ETDEWEB)

This guide explained the requirements for Off-Road Compression Ignition Engine Emission Regulations established under the Canadian Environmental Protection Act. The regulations are enforced by Environment Canada, which authorizes and monitors the use of the national emissions mark. The regulations prescribe standards for off-road engines that operate as reciprocating, internal combustion engines, other than those that operate under characteristics similar to the Otto combustion cycle and that use a spark plug or other sparking device. The regulations apply to engines that are typically diesel-fuelled and found in construction, mining, farming and forestry machines such as tractors, excavators and log skidders. Four different types of persons are potentially affected by the regulations: Canadian engine manufacturers; distributors of Canadian engines or machines containing Canadian engines; importers of engines or machines for the purpose of ...

Energy Technology Data Exchange (ETDEWEB)

We have researched several new focused ion beam (FIB) micro-fabrication techniques that offer control of feature shape and the ability to accurately define features onto nonplanar substrates. These FIB-based processes are considered useful for prototyping, reverse engineering, and small-lot manufacturing. Ion beam-based techniques have been developed for defining features in miniature, nonplanar substrates. We demonstrate helices in cylindrical substrates having diameters from 100 {micro}m to 3 mm. Ion beam lathe processes sputter-define 10-{micro}m wide features in cylindrical substrates and tubes. For larger substrates, we combine focused ion beam milling with ultra-precision lathe turning techniques to accurately define 25-100 {micro}m features over many meters of path length. In several cases, we combine the feature defining capability of focused ion beam bombardment with additive techniques such as evaporation, sputter deposition and electroplating in order to ...

International Nuclear Information System (INIS)

Purpose: The aim of this study was to create, perfect and test a hyperthermia balloon catheter for local treatment of cholangiocarcinoma. The device should induce hyperthermia in tumor tissue by acting locally in the bile duct lumen in contact with the tumor-infiltrated duct wall. In addition, it should exert tissue compression to cause an appreciable reduction in tumor microvasculature flow, thus improving thermal performance. Methods: According to the design specifications, the working temperature range should allow the device to be used for hyperthermia therapy either in combination with radiation and/or chemotherapy(radio/chemo-sensitizing effect at 42-45 deg. C) or alone (induction of coagulation necrosis above 65 deg. C). The balloon serves as an anchoring system during treatment and as a functional element to induce tissue compression. In vitro mechanical evaluation of the pressure/volume relationship, with the balloon inside rigid ...

Energy Technology Data Exchange (ETDEWEB)

Among the items of the Sunshine Project in fiscal 1981 for development of a solvent extraction and liquefaction plant, this paper describes the achievements in developing secondary hydrogenation. A small continuous hydrogenation device equipped with three reaction columns that can be filled with catalyst of 50 cc, and a dedicated testing room were designed, and orders were placed with manufacturers. The fabrication, assembly, delivery, installation, piping and wiring were all completed. The device passed a completion inspection based on the high-pressure gas safety assurance law in December 1981. After leakage due to gas and material oil was checked, a trial operation was performed, and verified of normal operation. A screening test was carried out on three kinds of commercially available and prototype catalysts before testing the SRC containing material for studying the secondary hydrogenation. The circulating solvent ...

Energy Technology Data Exchange (ETDEWEB)

The use of high-performance ion exchangers allows a trace-matrix-separation (SMT) directly followed by an ion chromatographic (IC) separation of the analytes. Based on the principles described in Part 1, a combined procedure IC-SMT-IC for metallic impurities in Mo and W is presented. Up to 12 metal traces (Fe, Cu, Pb, Zn, Ni, Co, Cd, Ca, Mn, Sr, Mg and Ba) can be determined in one run with 35 min. A special method for traces of U and Th is also given. Detection limits are typically 10-100 ng g{sup -1} in the metal sample. (author). 14 refs.; 10 figs.; 6 tabs.

J-STORE (Japan)

Full Text Available

Science.gov (United States)

...false Manufacturing and production engineering costs. 31.205-25 Section...205-25 Manufacturing and production engineering costs. (a) The costs of manufacturing and production engineering effort as described in (1)...

J-STORE (Japan)

Full Text Available

J-STORE (Japan)

Full Text Available

Science.gov (United States)

... qhmhk pqqnuu uossu nukjholmkjpfdju piefgqh^c]_bmaa\\d\\^cbi^la\\e`icYddgb va]ZV [X`mZZnZpW\\e_W_]Ys[`Z_Z`d g`a_egkknilelkki krlnflpkqou xmrv sohlmjepf ...

Science.gov (United States)

... `ffehhlqqke_hm`Ygfhgirxtnkhdhhicbd`_gompnjgkkiiifdfdigWWeljgcXNaf_\\` eghhkmhhglfbmkqpigoxyoili_X\\ahn YS[ijVIYeoqpppk[YRN[dehhcb_icYXV^ c_ZglmgdjolkhmpljgY ...

International Nuclear Information System (INIS)

The Nuclear Assurance Corporation (NAC) owns and operates four NAC-1 truck casks. These casks are used to ship spent reactor fuel assemblies and radioactive reactor-core components. The casks have been loaded or unloaded at a total of fifteen nuclear facilities in the United States. In addition, NAC has used another large, overweight-truck cask to ship radioactive reactor core components from a reactor to a waste burial site. There are many individual differences in the cask handling facilities at each of the reactor stations, nuclear research facilities and the storage and burial sites serviced. Various types of auxiliary lifting and handling devices for on-site cask operations have been required. The quality assurance requirements for the equipment used in interfacing casks with nuclear power plant facilities have become more stringent. This paper presents details on the type of special equipment being employed, the quality assurance requirements that are ...

International Nuclear Information System (INIS)

The UK Energy Research Centre (UKERC) in it's submission to the DTI's 2006 Energy Review reminded us that the 'UK has abundant wind, wave and tidal resources available; its mild climate lends itself to bio-energy production, and solar radiation levels are sufficient to sustain a viable solar industry'. These technologies are at different stages of development but they all draw on basic and applied Science and Engineering. The paper will briefly review the renewable energy technologies and their potential for contributing to a sustainable energy supply. Three research topics will be highlighted that bridge the gap between the physics underpinning the energy conversion, and the engineering aspects of development and deployment; all three are highly relevant to the Government's programme on micro-generation. Two are these are taken from field of thin film photovoltaics (PV), one related to novel device development and the other to a measurement technique for assessing ...

International Nuclear Information System (INIS)

Much research has been done to estimate the residual stress on a dissimilar metal weld. There are many methods to estimate the weld residual stress and FEM (Finite Element Method) is generally used due to the advantage of the parametric study. And the X-ray method and a Hole Drilling technique for an experimental method are also usually used. The aim of this paper is to develop the appropriate FEM model to estimate the residual stresses of the dissimilar overlay weld pipe. For this, firstly, the specimen of the dissimilar overlay weld pipe was manufactured. The SA 508 Gr3 nozzle, the SA 182 safe end and SA376 pipe were welded by the Alloy 182. And the overlay weld by the Alloy 52M was performed. The residual stress of this specimen was measured by using the Neutron Diffraction device in the HANARO (High-flux Advanced Neutron Application ReactOr) research reactor, KAERI (Korea Atomic Energy Research Institute). Secondly, FEM Model on the ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of the Spatial Signature Analysis (SSA) Electrical-test (e-test) validation study that was conducted between February and June, 1998. SSA is an automated procedure developed by researchers at the Oak Ridge National Laboratory to address the issue of intelligent data reduction while providing feedback on current manufacturing processes. SSA was initially developed to automate the analysis of optical defect data. Optical defects can form groups, or clusters, which may have a distinct shape. These patterns can reveal information about the manufacturing process. Optical defect SSA uses image processing algorithms and a classifier system to interpret and identify these patterns, or signatures. SSA has been extended to analyze and interpret electrical test data. The algorithms used for optical defect SSA have been adapted and applied to e-test binmaps. An image of the binmap is created, and features such as geometric ...

Energy Technology Data Exchange (ETDEWEB)

Section 127 of the Energy Policy Act requires that the Department of Energy (DOE) prepare a report to Congress on the potential for the development and commercialization of appliances that substantially exceed the present federal or state efficiency standards. Candidate high-efficiency appliances must meet several criteria including: the potential exists for substantial improvement (beyond the minimum established in law) of the appliance`s energy efficiency; electric, water, or gas utilities are prepared to support and promote the commercialization of such appliances; manufacturers are unlikely to undertake development and commercialization of such appliances on their own, or development and production would be substantially accelerated by support to manufacturers. This report describes options to improve the efficiency of residential appliances, including water heaters, clothes washers and dryers, refrigerator/freezers, dishwashers, space ...

Science.gov (United States)

The effect of 50 Hz and 60 Hz (frequencies of current distribution) and 20 kHz to 50 kHz (frequencies of induction cooktop) magnetic interference on implanted pacemakers have been assessed with the present generation of device technology. Sixty patients implanted in 1998 and 1999 with dual chamber pacemakers from 9 different manufacturers were monitored with telemetry while passing through, and standing between a system of two coils. They generated a 50 Hz or a 60 Hz magnetic field at 50 microT. Then, patients used a cooktop at different power. The recordings were made with the standard setting of "medically correct" sensing parameters chosen for the patients. Then pacemakers were reprogrammed to the unipolar mode, with the highest atrial (A) and ventricular (V) sensitivity that did not induce muscular inhibition while moving. Between each exposure (50 Hz, 60 Hz or 20 kHz to 50 kHz), the pacemaker programmation was controlled. At the end of the ...

Energy Technology Data Exchange (ETDEWEB)

There is considerable interest in the use of silicon devices as qubits for quantum computing. The existence of nuclear spin in a silicon isotope and the complex band structure of silicon are unfavourable for this application of silicon devices. (viewpoint)

Science.gov (United States)

... design, and manufacturing knowledge have been acquired and used to develop an 'in-house' capability for the fabrication of magnetic forming coils ...

Energy Technology Data Exchange (ETDEWEB)

Both the increased complexity of integrated circuits, resulting in six or more levels of integration, and the increasing use of flip-chip packaging have driven the development of integrated circuit (IC) failure analysis tools that can be applied to the backside of the chip. Among these new approaches are focused ion beam (FIB) tools and processes for performing chip edits/repairs from the die backside. This paper describes the use of backside FIB for a failure analysis application rather than for chip repair. Specifically, they used FIB technology to prepare an IC for inspection of voided metal interconnects (lines) and vias. Conventional FIB milling was combined with a super-enhanced gas assisted milling process that uses XeF{sub 2} for rapid removal of large volumes of bulk silicon. This combined approach allowed removal of the TiW underlayer from a large number of Ml lines simultaneously, enabling rapid localization and plan view imaging of ...

Wastenet

...ISO - ISO Standards - TC 156 - Corrosion of metals and alloys go to main navigation go to content area go to search International Standards for Business,...ISO Members FAQs Fr ISO Store Products ISO Standards By TC TC 156 Corrosion of metals and alloys ISO Store ISO Standards By ICS By ...aerospace standards Publications and e-products ISO Concept Database (ISO/CDB) Copyright TC 156 - Corrosion of metals and alloys Items to be displayed: Published ...responsibility of TC 156 Secretariat Standard and/or project Stage ICS 3ISO/WD 7441 Corrosion of metals and alloys Determination of bimetallic corrosion in outdoor ...

Energy Technology Data Exchange (ETDEWEB)

This paper addresses one source of degradation in OPV devices: the metal/organic interface. The basic approach was to study the completed device stability vs. the stability of the organic film itself as shown in subsequent devices fabricated from the films.

J-STORE (Japan)

Full Text Available

Science.gov (United States)

... in the design of such devices as fusion reactors, magnetohydrodynamic generators, magnetically levitated vehicles, magnetic forming devices, and ...

International Science & Technology Center (ISTC)

Research and Development of Resource-Saving Technology for Manufacturing of Titanium Semifinished Items from Chips

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

J-STORE (Japan)

Full Text Available

Science.gov (United States)

... Descriptors : *TERMINAL BALLISTICS, *WOUND BALLISTICS, VELOCITY, CONVERSION, REPRINTS, TISSUES(BIOLOGY), MANUFACTURING ...

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Two 16 electron titanacyclobutanes of the formula Ti(C5H4R)2(?2-CH2)2C(CH3)(i-C3H7) (R=H, CH3) have been prepared from the reaction of Ti(C5H5)2(?2-CH2)(?2-Cl)Al(CH3)2 or Ti(C5H4CH3)2(?2-CH2)(?2-Cl)Al(CH3)2 with H2C=C(CH3)(i-C3H7). Structural parameters, most notably lengthened C?C bonds in the titanacyclobutane ring, for both complexes reveal the expected presence of (C?C)?Ti agostic interactions. The complexes are isomorphous, crystallizing in the monoclinic space group Cc. For Ti(C5H5)2(?2-CH2)2C(CH3)(i-C3H7), a?=?11.3459(3)??, b?=?16.2108(4)??, c?=?8.1646(2)??, ??=?105.5276(16)?, V?=?1446.87(6)?, Dcalc?=?1.268 at 150(1)?K. For Ti(C5H4CH3)2(?2-CH2)2C(CH3)(i-C3H7), a?=?12.6591(2)??, b?=?16.2795(4)??, c?=?8.2462(2)??, ??=?107.2421(14)?, V?=?1623.04(6)??3, Dcalc?=?1.245 at 150(1)?K. Graphi...

International Nuclear Information System (INIS)

Projectilelike fragments following the 80 MeV "1"6O+"2"7Al reaction have been detected using a Bragg-curve spectroscopy ionization chamber (BCS-IC). The atomic number is deduced from the Bragg-peak amplitude. Nitrogen isotopes are clearly resolved using either range or energy loss data. This is the first application of the BCS method for complete ion identification in a heavy-ion-induced reaction.

Energy Technology Data Exchange (ETDEWEB)

A special purpose hardware machine, which simulates up to one half-million gates and 2m byte RAM ICS at a 5 millisecond clock speed is described. This is accomplished with a hardware logic (HAL) simulator. This performance is achieved with 32 distributed special parallel processors, which utilize block oriented simulation technique. The technique promises a good cost hardware logic simulator. 7 references.

International Nuclear Information System (INIS)

Using high resolution and high sensitivity IRAS data at 12 and 25 microns low mass stars were studied which have recently formed in the Ophiuchus, Corona Australis, and IC1396 dark clouds. The successful application of these techniques to the Rho Ophiuchi infrared cluster is briefly described. The status of research performed is also presented.

International Nuclear Information System (INIS)

The Institute of Electrical and Electronic Engineers (IEEE) standards for the quality assurance requirements for the design and manufacture of Class 1E instrumentation and electric equipment for a nuclear power generating station are presented. This standard establishes Quality Assurance Program requirements for electrical manufacturers. This standard, used in conjunction with ANSI N45.2-1977 and the supplemental standards to the extent referenced in this standard, is intended to meet the requirements of 10CFR50, Appendix B. These requirements are intended to assure that Class 1E instrumentation and electric equipment are responsibly engineered and manufactured from proper materials, that the manufacturing processes and practices are controlled, and that the manufacturing process produces a product of the required quality for Class 1E application.

Energy Technology Data Exchange (ETDEWEB)

Except nuclear industry, diverse structures (hospitals, of research or manufacturers) can have appeal to the use of radioisotopes conditioned under unsealed shape. Such practices lead to tolerate releases in environment in the respect of a statutory device. So the collective network can contain radioisotopes the future of which is going to depend partially on the cleaning applied to waste water. This study through the analysis of a concrete case, has for objective to inform about the future of gamma radioelements present in waste water treated by a wastewater treatment plant. The contamination of the network is essentially due to Tc{sup 99} and I{sup 131}, radioelements present whatever the working day and the hour considered. The total estimated in-load for a day is important, of the order of 4000 MBq for Tc{sup 99} and 15 to 300 MBq for I{sup 131}. The assessment of cleaning of the station shows that this one plays a role towards this ...

Energy Technology Data Exchange (ETDEWEB)

Thermoplastic encapsulation has been extensively studied at Brookhaven National Laboratory`s (BNL) Environmental and Waste Technology Center (EWTC) as a waste encapsulation technology applicable to a wide range of waste types including radioactive, hazardous and mixed wastes. Encapsulation involves processing thermoplastic and waste materials into a waste form product by heating and mixing both materials into a homogeneous molten mixture. Cooling of the melt results in a solid monolithic waste form in which contaminants have been completely surrounded by a polymer matrix. Heating and mixing requirements for successful waste encapsulation can be met using proven technologies available in various types of commercial equipment. Processing techniques for thermoplastic materials, such as low density polyethylene (LDPE), are well established within the plastics industry. The majority of commercial polymer processing is accomplished using extruders, mixers or a combination of these ...

Science.gov (United States)

Aluminum, due to its low density and low cost, is a key material for future lightweight applications. However, like other structural materials, aluminum is subject to various forms of corrosion damage that annually costs the United States approximately 5% of its GNP [1]. The main goal is to investigate the effects of various solution anions on aluminum surfaces, and specifically probe pit initiation and inhibition. Using surface analysis techniques including X-ray photoelectron spectroscopy, Auger electron spectroscopy, and scanning electron microscopy, results have been correlated with those obtained from electrochemical methods and a radiolabeling technique developed in the Wieckowski laboratory. Analysis of data has indicated that important variables include type of anion, solution pH, and applied electrode potential. While aggressive anions such as chloride are usually studied to elucidate corrosion processes to work ultimately toward inhibition, its corrosive properties can be ...

Energy Technology Data Exchange (ETDEWEB)

The device is designed for automatic testing of the degree of discharge of tractive storage batteries (AB) for electric loaders, electric cars and electric ore locomotives. The basic electrical schematic of the device is cited.

Science.gov (United States)

... POSITION VACANT: Program Manager (Advance Materials and Manufacturing), AD-340-4. Salary ranges from ... POTENTIAL: Program Manager (Advanced Materials and Manufacturing), AD-340-4. LOCATION: Directorate ...

Science.gov (United States)

Advanced aerospace vehicles and system components tend to be slim and elastic, ...... In the manufacturing sector, semiconductor manufacturing requires ... The energy generation and storage for modern-day sensor networks, ...... Current NASA roadmaps point towards development of new hydrocarbon fueled engines. ...

Science.gov (United States)

This paper summarizes the current scientific and technological knowledge about greenhouse gas emissions from various agricultural practices and the manufacturing of food. The study also provides estimates that compare agriculture-related alternatives for reducing greenhouse gas emissions.

UK PubMed Central (United Kingdom)

Toluene diisocyanate (TDI) and methylene diphenyldiisocyanate (MDI) are used in large quantities in the polyurethane foam manufacturing industry. Both substances are mutagenic and at least TDI is carcinogenic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper presents the description of methodological procedure specially developed for manufacturing mini turbines. This procedure is used in the design of a Francis type mini turbine with 12.5 kW. The housing volute and the suction tube of this equipment are manufactured with using composed material based on glass fiber and its distributor system is manufactured with stainless steel and brass. At the end it is presented an estimate cost of design / manufacturing of such equipment and a comparison with other equipment in the market.

International Science & Technology Center (ISTC)

The Development of Basic Plasma-Chemical Technology for Manufacture of Low Cost Crystal Silicon for Solar Power Plants.

Science.gov (United States)

No abstract available.

Science.gov (United States)

... INDUSTRIAL PRODUCTION, MODULAR CONSTRUCTION, IGNITION, PLUGS, NITROCELLULOSE, COMBUSTIBLE CARTRIDGE CASES, FELTS ...

Science.gov (United States)

... Abstract : The beater additive process for manufacturing combustible cartridge cases is superior to the solvent resin, post-impregnation process. ...

Science.gov (United States)

... Casting Explosive forming Forging Electrohydraulic forming Extruding Magnetic forming Rolling Electroforming Drawing Powdered metal forming ...

Energy Technology Data Exchange (ETDEWEB)

Energy Related Inventions Program Number 613 was a two year program to commercialize a unique new wear material, Metal Reinforced Carbon Composite, MRCC. The program was designed to manufacture sample components of MRCC for evaluation by potential users and manufacturers. As a result of the program Burton Technologies Inc. and Rotary Power International are forming a joint company to manufacture, market and license MRCC materials to a wide range of industries.

Wastenet

... News In Practice UK work Key facts & information Mass Balance Projects Resources & Library Technical Area Contacts Site Map Benchmarking solvent waste in the UK furniture manufacturing industry OrganisationBritish Furniture Manufacturers Ltd Project ReportSolvent Waste in Furniture Manufacturing Website: www.bfmenvironment.co.uk Return to list � RSWT | Website Design Quiet Storm Solutions Ltd Please consider upgrading your browser! If you can see this ...

Energy Technology Data Exchange (ETDEWEB)

A procedure and correlations are presented for predicting Charpy-impact energy, tensile flow stress, fracture toughness J-R curve, and J{sub IC} of aged cast stainless steels from known material information. The ``saturation`` impact strength and fracture toughness of a specific cast stainless steel, i.e., the minimum value that would be achieved for the material after long-term service, is estimated from the chemical composition of the steel. Mechanical properties as a function of time and temperature of reactor service are estimated from impact energy and flow stress of the unaged material and the kinetics of embrittlement, which are also determined from chemical composition. The J{sub IC} values are determined from the estimated J-R curve and flow stress. Examples of estimating mechanical properties of cast stainless steel components during reactor service are presented. A common ``lower-bound`` J-R curve for cast stainless steels of unknown ...

Energy Technology Data Exchange (ETDEWEB)

An ambitious development programme culminated in late 1989 with the most modern diesel train available today entering commercial service. At the root of its development lay an overall concept which aimed at meeting the present-day and future requirements of railway administrations. Higher passenger revenues, lower operating costs and reduced maintenance are the result. An IC trainset is 58.8 m long and consists of three cars: Two identical power cars and one intermediate car. Each three-car trainset has 144 seats, 16 of which are reserved for first class. Up to five three-car trainsets can be coupled rogether to form a 15-car trainset. Four air-cooled 8-cylinder diesel engines with a combined rating of 294 kW power each three-car trainset, i.e. there are two engines installed in each of the power cars. The train has a maximum speed of 180 km/h. (orig.).

International Nuclear Information System (INIS)

Photometric and kinematic observations of the peculiar S0 galaxy IC 4767, the X-galaxy, are presented. At various intensities the bulge of this galaxy looks like a normal spheroidal system with elliptical isophotes, a well-defined rectangle, and a peanut-shaped or X-shaped structure with components aligned at oblique angles to the major axis. The observations reveal a rapidly rotating inner disk of gas and dust which is nearly aligned with the major axis. The presence of gaseous emission alone suggests an accretion event. The stars in the outer regions of the X-component are rotating nearly as rapidly as the gas in the main disk, indicating that they are in relatively circular orbits. The five most prominent peanut-shaped bulges all have several nearby companions, evidence that the peanut deformity is due to interaction between galaxies. An analogy with the formation mechanism proposed for polar-ring galaxies suggests how an X-shaped component could develop from ...

Energy Technology Data Exchange (ETDEWEB)

The design of the KSTAR (Korea Superconducting Tokamak Advanced Research) tokamak (R{sub 0} = 1.8 m, a= 0.5 m, {kappa} = 2, {delta} = 1.8 B{sub T} = 3.5 T, I{sub p} 2 MA, {tau}{sub pulse} = 300 s) is being undertaken to do long-pulse. high {beta}, advanced tokamak operating-mode fusion physics experiments. The ion cyclotron (IC) system will deliver 6 MW of rf power to the plasma in the 25 - 60 MHz frequency range, using a single four-strap antenna mounted in a midplane port. It will be used for ion heating, fast-wave current drive (FWCD), and mode conversion current drive (MCCD). The phasing between current straps in the antenna will be adjustable quickly during operation to provide the capability of changing the current-drive efficiency. The IC system will be capable of 300 s operation with 12 MW (upgrade) of rf power to the plasma. (author)

CERN Document Server

We have obtained UBVRI images with the Kitt Peak and Cerro Tololo 4-m telescopes and Mosaic cameras of seven dwarfs in (or near) the Local Group, all of which have known evidence of recent star formation: IC10, NGC 6822, WLM, Sextans B, Sextans A, Pegasus,and Phoenix. We construct color-magnitude diagrams (CMDs) of these systems, as well as neighboring regions that can be used to evaluate the degree of foreground contamination by stars in the Milky Way. Inter-comparison of these CMDs with those of M31, M33, the LMC, and the SMC permits us to determine improved reddening values for a typical OB star found within these galaxies. All of the CMDs reveal a strong or modest number of blue supergiants. All but Pegasus and Phoenix also show the clear presence of red supergiants in the CMD, although IC10 appears to be deficient in these objects given its large WR population. The bright stars of intermediate color in the CMD are badly contaminated by ...

Energy Technology Data Exchange (ETDEWEB)

This study was conducted to investigate the decomposition of three {gamma}-irradiated antibiotics (e.g., tetracycline, sulfamethazine, and lincomycin) and to compare the toxic effects on Daphnia magna, Vibrio fischeri, and Pseudokirchneriella subcapitata. The median cell growth inhibition concentrations (IC{sub 50}) of tetracycline, lincomycin, and sulfamethazine for P. subcapitata dramatically increased (e.g., toxicity decreased) after radiolysis. The results demonstrated that {gamma}-radiation treatment was efficient to decompose antibiotics and thereby their toxicity on P. subcaptitata remarkably decreased due to reduced parent compounds.

Science.gov (United States)

C C*R C" dC*9 4hC2 CX2VCTF CK/XCL` CCNA C?Q C.:FC C?v As1)Ax^IA} AyU$ =FA%WNA AfgJA Aw;ZAzg AyA!A A=!nA> CA!n/A* ? ...

International Nuclear Information System (INIS)

Cerebral blood flow (CBF) and cerebrovascular reserve capacity (CRC) were measured by stable xenon computerized tomography (Xe-CT) and acetazolamide test in 15 patients with cerebrovascular disease before and after extracranial-intracranial (EC-IC) bypass surgery for minor stroke, reversible ischemic neurological deficit or transient ischemic attack. All had angiographically shown occlusive lesions of the major arterial trunk. In the present series, global analysis showed that the bypass did not increase the resting rCBF, but did increase the rCRC. We divided the patients into four groups according to the preoperative resting rCBF and rCRC. All 3 patients with normal resting rCBF and reduced rCRC showed postoperative improvement of rCRC. Of 6 patients with reduced CBF and reduced CRC, three had postoperative increase in resting CBF and four had increased CRC. One of two patients with reduced CBF and normal CRC showed only an increase in CRC. We propose that reduced ...

International Nuclear Information System (INIS)

This paper reports, to complement current knowledge on brain development, late regional brain maturation assessed with quantitative MR imaging. Axial and coronal head spin-echo (SE) images were obtained in 60 healthy individuals aged 5--56 years, with a double-echo, flow compensated imaging sequence obtained with a 1.5-T Magnetom spectroscopy and imaging system. T2-weighted images were calculated from the intensity differences in SE images at echo times (TEs) of 15 and 90 msec (TR = 2.5 second). The mean T2 values were determined at 16 sites in each cerebral hemisphere. T2 values of the six frontal subcortical white matter (FSCWM) sites and of the internal capsule (IC) were evaluated. Mean T2 values in the IC decreased until age 10 years, whereas this decrease continued in the FSCWM past age 15 years before reaching a plateau. Differential age-dependent patterns of mean T2 values emerged between the six FSCWM sites. The spread of T2 values ...

Energy Technology Data Exchange (ETDEWEB)

This is a process for manufacturing a semi-rigid, folding solar generator manufactured from several coated solar cells (Cics), which has at least two folding parts connected together so as to turn by hinges, characterized by the following stages of the process: a) On the back of matrix subsections, in order to cover the connector, carbon fibre strips are glued on, which project over the upper or lower edge of each matrix subsection. b) The projecting ends of adjacent carbon fiber strips are connected with two carbon fibre strips. c) At least two matrix subsections are fixed in separately manufactured carbon fiber frames, and d) the carbon fiber frames, together with the matrix subsections are connected via hinges to a solar generator.

International Nuclear Information System (INIS)

In the frame of the Primary Wall Module prototype manufacturing for ITER, a consistent R and D phase was conducted in order to identify the industrial allowable tolerances and manufacturing problems which would occur when joining pieces by HIPping process during the PW module manufacturing. The purpose of this development was to give as industrial as possible manufacturing routes for joining together large Stainless Steel or DS-Copper pieces with Stainless Steel tubes and for bonding Beryllium tiles onto a curved component surface. The study concerned surface preparations, allowable gaps and joint geometry, Beryllium tile geometry, Titanium interlayer thickness, etc. This R and D phase also allowed the development and validation of different ultrasonic inspection tools needed for plate-plate, tube-plate, edge to edge plate bonding.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Single-event burnout (SEB) sensitivity was tested for power MOSFET devices, JTMCS081 and JTMCS062, which were made in Institute of Microelectronics, Chinese Academy of Sciences, using californium-252 simulation source. SEB voltage threshold was found for devices under test (DUT). It is helpful for engineers to choose devices used in satellites. (authors)

International Nuclear Information System (INIS)

... amplification exhaust systems fluidic control devices gloveboxes pressure

International Nuclear Information System (INIS)

... bwr type reactors closures fluidic control devices operation performance pwr

Energy Technology Data Exchange (ETDEWEB)

Short communication.

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

... fluidic control devices performance reactor control systems space propulsion

J-STORE (Japan)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A centering device for casing tubings is proposed. It includes a housing, collar made of copper linings, return springs and pusher with centering pins placed in it. In order to simplify the design of the centering device it is equipped with levers installed on the pusher rod and connected by hinges to one another. The centering device assures coaxial placement of tubes over the mouth of wells and installation of butt joints during welding of tubes.

Energy Technology Data Exchange (ETDEWEB)

Achieving device independence for software applications is required for all but a small number of critical real time applications. Device independence is achieved by establishing protocols and building protocol interpreters for the specific devices. Data structures containing pointers to functions provide a flexible architecture for implementing protocol translation. 3 refs., 5 figs.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In the PV system with storage batteries, as a maximum power point tracking (MPPT) device is used to enhance battery charging, the enhancement must be greater than the internal loss of the device itself, or there will be no net gain at all. To evaluate the MPPT device benefits under different climate, the theoretical calculation models have been constructed. By simulation, a comparative study between two types of PV charge controllers with and without a MPPT device under different atmospheric conditions was presented. The comparison was made by means of the energy production obtained from the PV generator of each system. The climatic conditions of Beijing and Guangzhou in China have been regarded. From the results obtained it can be concluded that the effectiveness of the MPPT device in Guangzhou is not very obvious, however the MPPT device did greatly enhance ...

International Nuclear Information System (INIS)

This paper presents a rationale for and a summary of tasks and missions to which mobile and stationary robots and other teleoperator-controlled devices could be assigned in response to the accidental release of radioactive and other hazardous/toxic materials to the environment. Many of these vehicles and devices currently support operation and maintenance of nuclear power plants and other nuclear industry facilities. This paper also discusses specific missions for these devices at the Three Mile Island and Chernobyl nuclear power plant sites at the time of the accidents. Also discussed is the status of devices under development for future applications, as well as research on robotics.

International Nuclear Information System (INIS)

Remote-controlled handling systems are required for work to be done in the decommissioning and dismantling of nuclear facilities. These systems are equipped with electronic devices suitable for use in working environments affected by ionizing radiation. The publication explains the step-wise progress achieved for improving the radiation resistance of electronic devices with the example of a four-quadrant controlling device for the motors of a manipulator. The radiation resistance of the device could be enhanced to radiation energies of 5.500 Gy. This means that a manipulator vehicle equipped with this controlling device can take up to approx. 15 kGy all in all, taking into account its own shielding properties. (DG).

Energy Technology Data Exchange (ETDEWEB)

This report contains the results of the Photovoltaic (PV) Industry Manufacturing Technology Assessment performed by the Automation and Robotics Research Institute (ARRI) of the University of Texas at Arlington for the National Renewable Energy laboratory. ARRI surveyed eleven companies to determine their state-of-manufacturing in the areas of engineering design, operations management, manufacturing technology, equipment maintenance, quality management, and plant conditions. Interviews with company personnel and plant tours at each of the facilities were conducted and the information compiled. The report is divided into two main segments. The first part of the report presents how the industry as a whole conforms to ``World Class`` manufacturing practices. Conclusions are drawn from the results of a survey as to the areas that the PV industry can improve on to become more competitive in the industry and ...

British Library Electronic Table of Contents (United Kingdom)

This paper is aimed to present a fuzzy decision making approach to deal with the performance measurement in supply chain systems. In the manufacturing environment, performance measurement is based on different quantitative and qualitative factors. Some of these factors may have a larger effect on the performance measure than others. Units of measure of the quantitative factors are different such as time, money, percentage, ratio, and counts. Thus, this paper presents a performance measurement approach based on fuzzy set theory and the pair-wise comparison of Analytical Hierarchy Process (AHP), which ensures the consistency of the designer's assignments of importance of one factor over another to find the weight of each of the manufacturing activity in the departmental organization. In the ...

Energy Technology Data Exchange (ETDEWEB)

A variety of engineering and experimental applications require primary support structures which are self-centering. High mechanical strength, low-density, carbon fiber/epoxy matrix composite springs are used in unique planar, cylindrical, conical, and spherical configurations to self-center components. The sinusoidal and triangular-shaped composite springs are readily manufactured and assembled into component hardware. Design considerations, flexural strength properties, load bearing and centering data plus procedures for the manufacture of composite springs are presented.

Energy Technology Data Exchange (ETDEWEB)

The theoretical performance of ideal single- and multijunction cells are compared at 100xconcentration under a range of cloudless-sky conditions. The sensitivities of device performance to cell temperature and spectral variations are shown to depend on the number of junctions (one, two or three), the way in which the junctions are connected (series, parallel or independent), and the band gaps of the devices. The average performances of all of the multijunction devices surpass that of a single-junction GaAs device, but the inconsistency in performance of some of the multijunction devices is significant for large variations in cell temperature and incident spectrum. The choice of band gap and connection scheme is more important than the number of junctions in determining the consistency of device performance. (orig.).

Science.gov (United States)

Principle advantages of magnetic forming for part manufacture appear to lie ... to be an area of great potential for the magnetic forming process. We have a ...

Science.gov (United States)

as manufacturing plants and laboratories, including the Chemical Laboratory at the House of David in Benton Harbor, Michigan. Built in America: Historic Building Buildings Survey/...

Science.gov (United States)

... and facilities; the physical processing of materials into products; and processes associated with ... area of bulk silicon prod! uction as wafer material has been omitted, in keeping with current ...

UK PubMed Central (United Kingdom)

BackgroundBisphenol A (BPA) is a high-production-volume chemical commonly used in the manufacture of polycarbonate plastic. Low-level concentrations of BPA in animals and possibly...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundBisphenol A (BPA) is widely used in the manufacture of polycarbonate plastics, including infant formula bottles.ObjectivesBased on the...Full Text Available

Science.gov (United States)

... Stopper dialysis bags with hooded rubber stoppers. Dialysis bags are cellulose casing size #36 purchased from Visking Corporation. ...

Science.gov (United States)

International Patenting Trends in Advanced Materials: Ceramics (June 18, 1999) This report is the ... manufacturing, biotechnology, and advanced materials. Hypertext Format Portable Document Format ...

Energy Technology Data Exchange (ETDEWEB)

First French manufacturer of steel boilers, Geminox proposes the THRi series, composed of condensation gas boilers whose four mural for the propane model. (O.M.)

Science.gov (United States)

... commercial material manufactured utilizing chlorinated hydrocarbons for the sulfonation of a long chain polystyrene to produce high ... ...

Science.gov (United States)

the shear-beam design and the larger scale component test specimen. The subcompo - nents designed were: a. Web splice specimen. ...

Energy Technology Data Exchange (ETDEWEB)

AREVA is the world leader in the design and construction of nuclear power plants, the manufacture of heavy components, and the supply of nuclear fuel and nuclear services such as maintenance and inspection. The Equipment Division provides the widest range of nuclear components and equipment, manufactured at its two facilities in Jeumont, northern France, and St. Marcel, in Burgundy. The St. Marcel plant, set on 35 ha (87.5 acres) near Chalon-sur-Saone, was established in 1973 in a region with a long history of specialized metalworking and mechanical activities to meet the demand for non-military nuclear requirements in France. The site offers two advantages: - excellent facilities for loading and transporting heavy components on the Saone river, - it's proximity to other group sites. Since its completion in 1975, the Chalon/St. Marcel facility has manufactured all the heavy components for French pressurized water ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.

Wastenet

...been a world leader in the design, manufacture and installation of high quality precision-engineered systems for water and wastewater treatment fo Create Free Account ...

Wastenet

...on Environmental Expert Aanderaa Data Instruments develops, manufactures and markets oceanographic and meteorological instruments and special systems for collecting environmental data. Data can be ...

International Nuclear Information System (INIS)

The aim of the present study is to identify and characterize the antimalrial agents from traitional Sudanese medicinal plants. 49 plants parts representing 26 species from 15 families were extracted and screened for their in vitro antimalrial activity using P. falciparum strain 3D7 which is chloroquine sensitive and Dd2 strain which is chloroquine resistant and pyrimethamine sensitive.The plant species investigated exhibited diverse botanical families. They includes Annonaceae, Aristolochiaceae, Asteraceae, Balantiaceae, Caesalpiniceae, Celasteraceae, Cucurbitaceae, Fabaceae, Graminae, Meliaceae, Myrtaceae, Polygonaceae, Rubiaceae, Rutaceae, and simaroubaceae. The evaluation of these plants for their antimalarial activity and their effect on lymphocyte proliferation was carried out. 57 extracts were tested on the chloroquine sensitive strain (3D7). Where 34 extracts (59%) exhibited significant activity against 3D7 with IC_5_0 values #100 #mu# g/ml), where as ...

British Library Electronic Table of Contents (United Kingdom)

Background The lateral femoral cutaneous nerve (LFCN) can be at risk during, for example, the insertion of pins in the anterior superior iliac spine (ASIS) during external fixation of the pelvis, total hip arthroplasty through a direct anterior approach, open surgery for impingement in the hip through an anterior approach, and periacetabular osteotomy. During surgery, the surgeon usually assumes the location of the LFCN by using the ASIS as a landmark. Questions/purposes We investigated (1) whether there is any relationship between the LFCN and the ASIS and (2) the anatomy of the LFCN at the lateral border of the psoas major. Methods Using 25 formalin-fixed cadavers, we determined the location of the LFCN emergence point as above, same level with, or below the iliac crest (IC). We measured...

Energy Technology Data Exchange (ETDEWEB)

We report on the improvement of Critical Dimension (CD) linearity on a photomask by applying the concept of process proximity correction to a laser lithographic process used for fabrication of photomasks. Rule-based Laser Process proximity Correction (LPC) was performed using an automated optical proximity correction tool and we obtained dramatic improvement of CD linearity on a photomask. A study on model-based LPC was executed using a two-Gaussian kernel function and we extracted model parameters for the laser lithographic process by fitting the model-predicted CD linearity data with measured ones. Model-predicted bias values of isolated space (I/S), Arrayed Contact (A/C) and Isolated Contact (I/C) were in good agreement with those obtained by the nonlinear curve-fitting method used for the rule-based LPC.

British Library Electronic Table of Contents (United Kingdom)

Lung cancer is still difficult to treat by current chemotherapeutic procedures. We recently found that MVL, an anti-HIV lectin from blue-green algae Microcystis viridis, also has antitumor activity. The objective of this study was to investigate apoptosis-inducing activity of recombinant MVL (R-MVL) and proteomic changes in A549 cells, and to identify the molecular pathways responsible for the anti-cancer action of R-MVL. We found that R-MVL induces A549 cells apoptosis in a dose-dependent manner by using MTT assay, fluorescent microscope (FM) and flow cytometry (FCM), and the IC50 was calculated to be 24.12??g/ml. Subsequently, 7 altered proteins in R-MVL-treated A549 cells were identified, including upregulated aldehyde dehydrogenase 1 and ?-actin, and five downregulated proteins: heat s...

Energy Technology Data Exchange (ETDEWEB)

Fuji Electric has realized highly reliable and functional control systems by the dispersion type control system FOCUS, which uses the controller (ICS-2000) enjoying good reputation in controlling industrial plants for a long time and a personal computer with high windows operability, the former for controlling and the latter for MHI responsible for monitoring. The smelting process in a steel-making plant needs a highly reliable system for advanced control to ensure continuous operation. Fuji Electric delivered the FOCUS system to Kubota in 1998, as the smelting furnace instrumentation/control system for the cupola furnace. The system has been in service smoothly. Moreover, a total of four control systems have been delivered, 2 for steel-making furnaces and the other 2 for continuous casting. (NEDO)

British Library Electronic Table of Contents (United Kingdom)

Examining the relationship between biodiversity and functional stability (resistance and resilience) of activated sludge bacterial communities following disturbance is an important first step towards developing strategies for the design of robust biological wastewater treatment systems. This study investigates the relationship between functional resistance and biodiversity of dominant bacterial taxa by subjecting activated sludge samples, with different levels of biodiversity, to toxic shock loading with cupric sulfate (Cu[II]), 3,5-dichlorophenol (3,5-DCP), or 4-nitrophenol (4-NP). Respirometric batch experiments were performed to determine the functional resistance of activated sludge bacterial community to the three toxicants. Functional resistance was estimated as the 30?min IC50 or th...

British Library Electronic Table of Contents (United Kingdom)

Ethnobotanical and chemotaxonomical studies for antiparasitic activity of Colombian Annonaceae were carried out. In vitro antiprotozoal activity of 36 extracts obtained from six different species was determined against promastigotes of three Leishmania species, epimastigotes of Trypanosoma cruzi and both chloroquine sensitive (F32) and resistant (W2) Plasmodium falciparum. Cytotoxic activity was evaluated in U-937 cells. Active extracts were selected according their selectivity index (SI). Extracts from Annona muricata, Rollinia exsucca, Rollinia pittieri and Xylopia aromatica were active against Leishmania spp. and Trypanosoma cruzi showing IC50 values lower than 25mg/ml. Hexane extract from Rollinia pittieri leaves was the most selective against Trypanosoma cruzi and Leishmania spp. (IS=...

International Nuclear Information System (INIS)

The study reports the identification of different organic acids that are formed during the pyrohydrolysis of mixed carbide of uranium and plutonium using ion chromatography (IC). The identification of organic acids present in the pyrohydrolysis distillate is required to carry out interference free analysis of Cl and F. The study describes three stage isocratic separations with NaOH eluents having concentrations 2 mM, 10 mM and 50 mM respectively in order to separate and identify both aliphatic and aromatic acids. The present investigation identified formic, acetic, propionic, butyric, tartaric and oxalic acids in the distillate, however, aromatic acids could not be identified. (author)

Energy Technology Data Exchange (ETDEWEB)

Science and technology could be revolutionized by quantum computers, but building them from solid-state devices will not be easy. Robert W Keyes of IBM's research division outlines the challenges in scaling up the technology from lab experiments to practical devices. (U.K.)

International Nuclear Information System (INIS)

The patent relates to fluid operated devices for moving articles. The machine may be used in filling a nuclear fuel canister with fuel pellets where there is a tendency for out of squareness of pellets to produce a jam condition readily cleared by a modest force. (U.K.).

Science.gov (United States)

Coke-fired cupola furnaces were improved and made suitable for the production of high-quality casting melts by numerous additional devices. Moreover, they were equipped with environmental protection systems with numerous dust separation devices and afterb...

Energy Technology Data Exchange (ETDEWEB)

In this paper we discuss the effect on the emittance of the residual dispersion in the insertion devices. The dispersion in the straights could be generated by the lattice error, trim dipole, and insertion device. The effect on the emittance is examined, and the dispersion tolerances are given for the NSLS-11.

UK PubMed Central (United Kingdom)

The biomechanical nature of the arterial system and its major disease states provides a series of challenges to treatment strategies. Endovascular device design objectives have mostly centered on short-term...Full Text Available

Science.gov (United States)

...limited to, emission control devices, pumps, filters, muck cookers, stills, solvent tanks, solvent containers, water separators...facility that meets the conditions of § 63.320(g). Muck cooker means a device for heating perchloroethylene-laden...

International Nuclear Information System (INIS)

The influence of the main factors on device efficiency of pulsed liquid jet pump with gas-liquid piston is analysed, the theoretical equation and its time-averaged solution of pulsed liquid jet pump device efficiency are derived. The theoretical and experimental results show that the efficiency of transmission of energy and mass to use pulsed jet is greatly raised, compared with steady jet, in the same device of liquid jet pump. The calculating results of time-averaged efficiency of pulsed liquid jet pump are approximately in agreement with the experimental results in our and foreign countries

Science.gov (United States)

... Abstract : MANY THIN FILM ACOUSTO-OPTIC INTERACTION EXPERIMENTS FOR ... CONVERTERS, AND FOR FAST SWITCHES HAVE BEEN ...

International Nuclear Information System (INIS)

... Union (INTAS), Brussels (Belgium) Science and Technology Center in Unkraine,

Science.gov (United States)

... This is achieved by the use of a unique logic circuit employing a plurality of flip-flop devices, multivibrators and AND gates. ...

Science.gov (United States)

... increasing photorealism. Furthermore, developments in audio technology continue to increase the spatial awareness of users in VEs. ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses design considerations for the recently introduced GaInP/GaAs monolithic tandem concentrator cell. The prototype device achieves a peak efficiency of 30.2% in a range of 140--180 suns, making this the first two-terminal device to demonstrate a verified efficiency exceeding 30%. At 425 suns the efficiency is still above 29%. The authors focus on the issues of grid design, top-cell thickness, and antireflectance coat. They also examine ways in which these aspects of the device may be modified to provide further performance improvements for future devices.

Science.gov (United States)

sabot: A device fitted around or in back of a projectile in a gun barrel or launching tube to support or protect the projectile or to prevent the escape of ...

British Library Electronic Table of Contents (United Kingdom)

The individuality of production devices should be taken into account when statistical models are designed for parallelized devices. In the present work, a new clustering method, referred to as NC-spectral clustering, is proposed for discriminating the individuality of production devices. The key idea is to classify samples according to the differences of the correlation among measured variables, since the individuality of production devices is expressed by the correlation. In the proposed NC-spectral clustering, the nearest correlation (NC) method and spectral clustering are integrated. The NC method generates the weighted graph that expresses the correlation-based similarities between samples, and the constructed graph is partitioned by spectral clustering. A new statistical process monit...

Science.gov (United States)

Resistance exercise has been widely reported to have positive rehabilitation effects for patients with neuromuscular and orthopaedic conditions. This paper presents an optimal design of magneto-rheological fluid dampers for variable resistance exercise devices. Adaptive controls for regulating the resistive force or torque of the device as well as the joint motion are presented. The device provides both isometric and isokinetic strength training for various human joints.

Energy Technology Data Exchange (ETDEWEB)

A method and apparatus is provided for detecting explosives by thermal imaging. The explosive material is subjected to a high energy wave which can be either a sound wave or an electromagnetic wave which will initiate a chemical reaction in the explosive material which chemical reaction will produce heat. The heat is then sensed by a thermal imaging device which will provide a signal to a computing device which will alert a user of the apparatus to the possibility of an explosive device being present.

Energy Technology Data Exchange (ETDEWEB)

The results of Sandia National Laboratories' participation in the NASA Planetary Definition and Design Program are summarized. Areas reported include the characterization of large area cadmium zinc telluride spectrometers and the application of simulation techniques to the prediction of device performance. Also investigated was the response of mercuric iodide devices in the region from 1 to 100 KeV. A literature study to determine the status or radiation damage measurements in room temperature semiconductor devices is also reported.

Energy Technology Data Exchange (ETDEWEB)

The purpose of the invention is to increase reliability in the operation of the device for advancing the base of a stoping unit. This is achieved because the device includes alternation hydraulic jacks of advance and control connected by hinges between themselves by the sections of the base and equipped with hydraulic locks, distributors of the hydraulic jacks of advance. In this case the hydraulic locks connected to the hydraulic jacks of control are doubled and connected to the distributors of the neighboring sections through reverse valves.

Energy Technology Data Exchange (ETDEWEB)

Heavy-ion irradiation technique has been developed for the evaluation of single-event effects on semiconductor devices. For the uniform irradiation of high energy heavy ions to device samples, we have designed and installed a magnetic beam-scanning system in a JAERI cyclotron beam course. It was found that scanned area was approximately 4 x 2 centimeters and that the deviation of ion fluence from the average value was less than 7%. (author)

International Nuclear Information System (INIS)

Large scale flows of liquids can be controlled by using power fluidic devices that harness the hydrodynamic properties of liquids rather than use moving parts. Included among the fluidic devices considered are fluidic pumps, reverse flow diverters, fluidic diodes and vortex amplifiers. These devices are of potential use in the nuclear industry, particularly in reprocessing. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

A description is given of the principal steps involved in `USIMINAS` work roll manufacturing project for its tandem cold mill. The service performance of these rolls was found to be similar to that rolls supplied by traditional manufacturers. (author). 5 refs., 5 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

The document reports the results of a cost-effectiveness analysis of alternative water pollution control regulations of the battery manufacturing industry. These regulations include effluent limitations and standards based on best practical control technology currently available, best available technology economically achievable, and pretreatment standards for new sources. For each of these regulations, EPA has identified several pollution control options, each with different levels of pollution abatement and compliance cost. The analysis is a tool for evaluating the options.

International Nuclear Information System (INIS)

In the frame of the European Technology R and D programme for International thermonuclear experimental reactor (ITER) and in the area of high heat flux plasma facing components (HHFC), representative small-scale mock-ups were manufactured and tested to compare different concepts and joining technologies (i.e. active brazing, hot isostatic pressing (HIPping), diffusion bonding, etc.). On the basis of the results obtained by thermal fatigue tests, the monoblock concept resulted to be the most robust one, particularly when the HIPping manufacturing technology is used. Within this programme, ENEA developed an alternative technique for manufacturing plasma-facing components with a monoblock geometry of the ITER machine. The basic idea of this technique, named hot radial pressing (HRP), is to perform a radial diffusion bonding between the cooling tube and the armour tile by pressurising the internal tube only and by keeping the ...

International Nuclear Information System (INIS)

In the frame of the European Technology R and D program for ITER, and in the area of High Heat Flux plasma facing Components (HHFC), representative small-scale mock-ups were manufactured and tested to compare different concepts and joining technologies (i.e. active brazing, Hot Isostatic Pressing (HIPping), diffusion bonding, etc.). On the basis of the results obtained by thermal fatigue tests, the monoblock concept resulted to be the most promising one, particularly when the HIPping manufacturing technology is used. Within this program, ENEA manufactured tungsten monoblock mock-ups by using the HIPping technology. The mock-ups were tested with respect to thermal fatigue and, upon screening tests, the best performance obtained was 15 MW/m"2 for 200 cycles. One of these mock-ups was enclosed in the 'Paride' neutron irradiation campaign. This campaign has the scope of enlarging the available database on the performance ...

Science.gov (United States)

The steroidogenic factor 1 (SF-1, also known as NR5A1) is a transcription factor belonging to the nuclear receptor superfamily. Whereas most of the members of this family have been extensively characterized, the therapeutic potential and pharmacology of SF-1 still remains elusive. Described here is the identification and characterization of selective inhibitory chemical probes of SF-1 by a rational ultra-high-throughput screening (uHTS) strategy. A set of 64,908 compounds from the National Institute of Health's Molecular Libraries Small Molecule Repository was screened in a transactivation cell-based assay employing a chimeric SF-1 construct. Two analogous isoquinolinones, ethyl 2-[2-[2-(2,3-dihydro-1,4-benzodioxin-7-ylamino)-2-oxoethyl]-1-oxoisoquinolin-5-yl]oxypropanoate (SID7969543) and ethyl 2-[2-[2-(1,3-benzodioxol-5-ylmethylamino)-2-oxoethyl]-1-oxoisoquinolin-5-yl]oxypropanoate and (SID7970631), were identified as potent submicromolar inhibitors, yielding ...

Energy Technology Data Exchange (ETDEWEB)

A real time neutron radiography system has been developed at the University of Michigan Phoenix Memorial Laboratory (PML) and has recently been used to test the imaging capabilities of a neutron imaging device developed by Lixi, Inc. of Downers Grove, Illinois. This device uses an input phosphor that is high in gadolinium to generate a light image which is then sent through an intensifier stage to provide images that can be viewed by eye, video camera, or standard 35 mm camera. It was determined that this device provides images of much higher resolution and sensitivity than those obtained with the imaging system currently being used at PML. Using computerized image enhancement techniques, the images obtained with the Lixi neutron imaging device can then be further enhanced or processed to obtain quantitative information on the object being imaged.

Energy Technology Data Exchange (ETDEWEB)

We summarize recent developments in x-ray microscopy of polymers by focusing on the characterization of organic electronic devices. The quantitative compositions of model polymer blends have been mapped at a resolution of {approx}35 nm. Since it could be inferred that these devices have structures smaller than 35 nm, quantitative compositional mapping at length scales below the present resolution limit of x-ray microscopy is required. Organic devices thus serve to both highlight the success of NEXAFS microscopy to date, but to also outline the very real need for higher spatial resolution. New approaches to create improved optics or different acquisition modalities are required if x-ray microscopy is to make sustained contributions to such an important area of research as organic devices.

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to a light weight underground pipe or cable installing device adapted for use in a narrow and deep operating trench. More particularly this underground pipe installing device employs a pair of laterally movable gates positioned adjacent the bottom of the operating trench where the earth is more solid to securely clamp the device in the operating trench to enable it to withstand the forces exerted as the actuating rod is forced through the earth from the so-called operating trench to the target trench. To accommodate the laterally movable gates positioned adjacent the bottom of the narrow pipe installing device, a pair of top operated double-acting rod clamping jaws, operated by a hydraulic cylinder positioned above the actuating rod are employed.

Energy Technology Data Exchange (ETDEWEB)

This article describes a flexible and extensible infrastructure for applying Web-Technologies to embedded systems.The presented approach develops a Three-level-Architecture consisting of the embedded system, the universal Remote-Access-Server and the Remote-Access-Client. A system-spanning general interface allows the binding of embedded systems in order to access their process data. Additionally, this procedure facilitates a flexible processing of the device data, so that it is ready to be used by different control devices. To ensure flexibility - connecting different devices on the one side and providing information for different clients like PC, PDA or mobile phone on the other side - a new XML-based description language (Service Description Markup Language - SDML) is introduced. The SDML documents contain information about connected embedded systems, reusable device data and the presentation ...

International Nuclear Information System (INIS)

An IAEA databank lists a number of reported cases of illicitly trafficked nuclear or other radioactive materials. Apart from the traditional concern with nuclear proliferation, the post September 11th public is now wary of a possible attack by terrorists with a nuclear or radiation dispersion device (RDD). Until now, the seized quantities have not been sufficient to manufacture a nuclear explosive device, but they might be enough to construct an RDD. Recognizing the latent global challenge to public health and safety, the G8 States (Japan, USA, Germany, France, UK, Italy, Canada, and Russia) have called for 'joint international efforts to identify and suppress illicit supply' of, and demand for, nuclear material and to deter potential traffickers. One measure gaining in significance is to identify seized material and trace it back to its origin the objective of an emerging science known as nuclear forensics. Repeatedly ...

DEFF Research Database (Denmark)

Based on case studies and action research, this paper investigates and discusses appropriate means for transfer knowledge when relocating manufacturing units. The cases include relocations both within the country and overseas. A framework for identifying suitable means is developed based on the situations which are extracted from the cases. Two parameters are used to classify the situation: the complexity of knowledge, and the environment for transferring the knowledge. Four different groups of means are identified from the case studies; 1) Documents or manuals and peer-to-peer training, 2) Scenarios on real systems, 3) Prototypes and games, and 4) Emulation. These means are evaluated based on the parameters in the framework and proper means are positioned in the framework. This framework can be used to support learning to develop knowledge in the new manufacturing unit.

British Library Electronic Table of Contents (United Kingdom)

Global supply chain practices and their effects have received considerable attention over the last two decades. In the recent past, the need for integration across supply chains has been identified as a key for effective and efficient operations of supply chains. This is observed with the increasing trend of collaborative partnerships among supply chain partners. This paper presents an integrated approach for manufacturing and distribution networks within the supply chain system of a global car company. The paper shows that the integration of manufacturing and distribution networks creates the environment for effective planning of many components and execution/follow-up of those plans. These components include materials, resources, operations/activities, suppliers and customers. The main f...

British Library Electronic Table of Contents (United Kingdom)

Customer relationships, product development, data integration and demand-driven supply chains are key concepts for companies that wish to remain competitive in today?s global economy. To address this important information management issue, the present study examines how, within a demand-driven network context, an eCRM can influence the interorganizational product development process between a manufacturer and its key customers. The theoretical model, built on research related to a technology assimilation model based on Fichman?s (2000) work, was tested on data from 104 manufacturers in the wireless equipment sector. The results show that the adoption of an eCRM does not moderate the relationship between collaborative e-product development involving a manufacturer and its key customers and ...

Energy Technology Data Exchange (ETDEWEB)

We have investigated tailoring damage effects of explosive devices by addition of unconventional materials, specifically combustible metals. Initial small-scale as well as full-scale testing has been performed. The explosives functioned to disperse and ignite these materials. Incendiary, enhanced-blast, and fragment-damage effect have been identified. These types of effects can be used to extend the damage done to hardened facilities. In other cases it is desirable to disable the target with minimal collateral damage. Use of unconventional materials allows the capability to tailor the damage and effects of explosive devices for these and other applications. Current work includes testing of an incendiary warhead for a penetrator.

International Nuclear Information System (INIS)

Field Programmable Gate Arrays (FPGAs) are being used in space applications because of attractive attributes: good density, moderate speed, low cost, and quick turn-around time. However, these devices are susceptible to Single Event Upsets (SEUs). An approach using triple modular redundancy (TMR) and feedback was developed for flip-flop hardening in these devices. Test data showed excellent results for this circuit topology. Total dose and Single Event Effect (SEE) testing have been performed on recently released technologies. Failures are analyzed and test methodology is discussed.

Energy Technology Data Exchange (ETDEWEB)

Recently, organic semiconducting materials have gained a broad interest due to their potential for organic electronic devices such as organic light emitting diode (OLED), organic photovoltaic devices and organic field-effect transistors (OFETs). Optical properties of organic semiconducting materials are important for practical application. For example, the power conversion efficiency of organic photovoltaic devices is mainly affected by absorption properties of organic materials. Proton irradiation is one of the efficient methods to change the optical properties of organic materials. In this paper, we investigate the changes of optical properties of various polymers using the proton irradiation.

International Nuclear Information System (INIS)

Experimentally it is shown that a movable grounded metallic plate placed inside a multi-dipole magnetic cage can vary the diffused plasma parameters such as density, plasma potential and electron temperature. Plasma is solely produced in the source section of a double plasma device by a dc hot filament discharge and a low-density plasma is produced in the target section by local ionization of neutral gas by the high energetic electrons coming from the source section. A grounded movable stainless steel plate is inserted in the target section of the device. The floating potential of the plate also changes depending on the position of the plate inside the magnetic cage.

International Nuclear Information System (INIS)

The feasibility of a high-energy electron cooling device has been studied through tests on a prototype of the electron device. The apparatus consists of a pulsed ((20-60) keV, 2#mu#s) electron gun, a drift region 1 m long and of a depressed collector for recovering the electron energy. Tests on beam optics and energy recovery have been performed, a high-energy recovery efficiency has been attained. Experimental results are discussed in this paper.

International Nuclear Information System (INIS)

Two new identical insertion devices have been designed for the Daresbury SRS. They are 2T permanent-magnet multipole wigglers that will provide high flux in the X-ray region. This paper describes the magnetic and mechanical design of the arrays of steel pole pieces and permanent-magnet blocks. Also given is the engineering design of the support structure that will cope with the very large forces present while maintaining high levels of precision in gap setting and parallelism. The engineering design has been fully assessed using finite-element techniques to predict the deflections of critical parts of the structure. These two devices are due to be installed into the SRS by the end of 1998.

International Nuclear Information System (INIS)

A novel device called the gas expansion model (GEM) is being developed at the Hanford Engineering Development Laboratory for testing in the 400-MW(th) fast flux test facility (FFTF) reactor. Incorporation of the GEM into liquid-metal reactor designs is intended to measurably contribute to the achievement of inherent safety, by allowing the reactor to passively shut down even in the extremely remote (hypothetical) event of an unprotected (no scram) loss-of-flow accident. The purpose of this paper is to describe the GEM and present predictive analyses of the effectiveness of the device during unprotected loss-of-flow experiments in the FFTF.

Energy Technology Data Exchange (ETDEWEB)

The program goals for the first quarter were to located and contact potential manufacturers of these components, evaluate their level of interest, and begin discussions of the type and design of the prototypes to be fabricated for their evaluation. Thoughtful discussion at this stage would result in fabricating prototypes which answer the greatest number of questions possible for a given manufacturer at the lowest cost to this program. In the present economy many manufacturing firms have almost no funds for testing and evaluating new materials. This places a greater burden on the data obtained from outside laboratories. In many cases this data will be used to make that first evaluation on MRCC`s (metal reinforced carbon composites) suitability for a given application and give firms the confidence to commit to a evaluation program. In Exhibit 1, which is attached to this report the authors have the first set of data from ...

International Nuclear Information System (INIS)

In 1972 a consortium consisting of Gebruder Sulzer A.G., Winterthur and EVT, Energie- und Verfahrenstechnik G.m.b.H., Stuttgart, was awarded the contract by HBR, Hochtemperatur Reaktorbau G.m.b.H., Koln/Mannheim, for the design, manufacture and installation of the 6 steam generator units for the prototype 300 MWe Thorium High Temperature Reactor (THTR) at Schmehausen, Germany. The design and manufacture of the 6 units is done by Sulzer; installation of the units as well as the manufacture of the external pipework and headers is done by EVT. The units are built under semiclean conditions in a special workshop at CCM-Sulzer in mantes, France. This workshop had been used previously for the manufacture of the steam generators for the nuclear power plants St. Laurent I, II, Vandellos (500 Mwe each) and EL-4 (70 Mwe). The present paper defines the operating conditions and the chemical composition of the ...

Energy Technology Data Exchange (ETDEWEB)

The pollutants from the exhausts of internal combustion engines cause a range of illnesses and are the main source of atmospheric contamination. This article explores the options for curbing pollution in the UK including catalytic converters, electric cars, and natural gas cars. It is likely that the onus will remain with the car manufacturers for developing solutions. (UK)

UK PubMed Central (United Kingdom)

OJECTIVEThis study seeks to identify practices of self-medication in the treatment of ocular emergencies. We examine patients’ use of both homemade preparations and manufactured...Full Text Available

UK PubMed Central (United Kingdom)

IntroductionRecent Food and Drug Administration legislation enables the mandating of product performance standards for cigarette smoke and the evaluation of manufacturers’...Full Text Available

Science.gov (United States)

Flywheels have the possibility of providing high turnaround efficiency and high specific power output. These characteristics are very important for the successful manufacture of parallel and series hybrid vehicles, which have the potential for providing h...

Science.gov (United States)

for an Air Force Manufacturing technology program whose aim is the establishment of organic matrix ...... display considerations for advanced energy/flight management sys- ...... Future System - The Roadmap of the System of the Future - ...... data storage units, pilot's guidance indicators, and a quick look ...

Science.gov (United States)

To perform the localization project of WOLSUNG reactor fuel, mass-production system of irradiation-stable and sound fuel pellet must be established. The following subjects have been carried out to set up CANDU fuel fabrication process for continuous produ...

UK PubMed Central (United Kingdom)

BackgroundLarviciding is a key strategy used in many vector control programmes around the world. Costs could be reduced if larvicides could be manufactured locally. The potential...Full Text Available

Science.gov (United States)

This report documents the collaborative effort between the United States and Canada to investigate the impact of process-induced defects on strength and stiffness under static and fatigue loading and for low-cost composite aircraft structures, in particul...

Science.gov (United States)

A substantial design and development program has been underway in the United States of America on the Darrieus vertical axis wind turbine (VAWT). The purpose of this report is to present currently available information on: design, construction, and testin...

Science.gov (United States)

The structural features of 25mm combustible cartridge cases, manufactured for this program and having nitrocellulose/resin/fiber ratios of 85/10/5, 80/15/5, 75/20/5 and 75/10/15, were characterized through permeability measurements, respectively, about 10...

International Nuclear Information System (INIS)

The Secure Automated Fabrication (SAF) line, an automated and remotely controlled manufacturing process, is scheduled for startup in 1987 and will produce mixed uranium/plutonium oxide fuel pins for the Fast Flux Test Facility (FFTF). The application of robotics in the fuel fabrication and supporting operations is described.

Science.gov (United States)

... and technology-. The United States National Technology Roadmap for Semiconductors [ 11 still ... Moreover, higher volumes of production, better manufacturing capabilities and ... energy-efficient, reliable, high-performance, embedded (real-time), highly miniaturized, .... Optical Computing, Storage, and Communications. ...

Science.gov (United States)

ADVANCED MODELING, S IMULATION, AND ANALYSIS (ROADMAP 14). ...... Metal/Silicon Extraction from Regolith & manufacturing ..... addresses solar power, energy storage (in conjunction with solar power and as a prime source of ...

Energy Technology Data Exchange (ETDEWEB)

The lithium-polymer energy storage technology requires the production of thin films of huge surface. The BT-EdF-CEA consortium has studied the various manufacturing techniques of these films and their assembly. The process was chosen according to its productivity, low expensiveness, ecological impact and energy performances with capacities reaching 40 Ah. This paper explains: the objectives and specifications of the project, the advantage of the consortium and the role of the different partners, the results (coating, dry extrusion and battery element manufacturing techniques), and the electrochemical performances of the elements. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

The technology based portion of the Advanced Turbine Systems Program (ATS) contains several subelements which address generic technology issues for land-based gas-turbine systems. One subelement is the Materials/ Manufacturing Technology Program which is coordinated by DOE Oak Ridge Operations and Oak Ridge National Laboratory (ORNL). The work in this subelement is being performed predominantly by industry with assistance from universities and the national laboratories. Projects in this sub-element are aimed toward hastening the incorporation of new materials and components in gas turbines.

International Nuclear Information System (INIS)

Wood-plastic combination (WPC) was produced by #gamma#-irradiation of persimmon impregnated with acrylonitrile and styrene. The hardness and strength of WPC obtained were higher than those of an unmodified wood. Thus, it was found that the WPC is suited for a head of golf club, because the Shore hardness value of WPC is 36% greater than that of unmodified wood. An impregnation method of monomers with some pigments could produce colored WPC without diminishing natural grain. Head of golf club could be manufactured from colored WPC in practice. (auhtor).

Energy Technology Data Exchange (ETDEWEB)

One of the most complicated tasks during the assembly of the Wendelstein W7-X is the installation of the superconductive coil system. The entire magnet system is enclosed between the Outer Vessel and the plasma vessel in high vacuum at 4 K. The coils are supported by a support structure, the Central Support Structure (CSS). The CSS carries all 70 coils, and it is designed as a closed ring made of 5 modules (10 half modules). The whole structure is supported by 10 Cryolegs which rest on the machine base. This paper describes the final design and manufacture of these Cryolegs.

Energy Technology Data Exchange (ETDEWEB)

Lead-acid batteries, one of eight types, account for about 70% of annualized control costs facing the battery manufacturing industry as a result of EPA's guidelines. This report is the industry's response. It makes counter recommendations for effluent limitations, discusses selected control technologies and effluent limitations, makes control cost estimates, and provides an economic impact analysis and a benefits effectiveness analysis.

International Nuclear Information System (INIS)

In one of the first uses of high Tc superconductors in an end-use product, Lake Shore Cryotronics and a Swiss lab have developed a liquid nitrogen level sensor using a high Tc thin film. The probe is manufactured using a seamless stainless steel tube with an yttrium-based zirconium oxide flame-sprayed on the tube. A plasma-sprayed superconductor compound is deposited on top of that. The probe is coated with a sealant that protects the superconducting film from the atmosphere. This manufacturing method has yielded an extremely durable product. Unaffected by ice formation and related mechanical problems, the superconducting level sensor can be kept in the dewar for long periods of time.

UK PubMed Central (United Kingdom)

BackgroundThe routine removal of orthopaedic fixation devices after fracture healing remains an issue of debate. There are no evidence-based guidelines on this matter, and little...Full Text Available