Energy Technology Data Exchange (ETDEWEB)

Plasma nitriding is usually used for ferrous materials to improve their surface properties. Knowledge of the properties of thin surface layers is essential for designing engineering components with optimal wear performance. In our study, we investigated the microstructural, mechanical and tribological properties of plasma- and pulse plasma-nitrided AISI 4140 steel in comparison to hardened steel. The influence of nitriding case depth as well as the presence of a compound layer on its tribological behaviour was also examined. Plasma and pulse plasma nitriding were carried out using commercial nitriding processes. Nitrided samples were fully characterised, using metallographic, SEM microscopic, microhardness and profilometric techniques, before and after wear testing. Wear tests were performed on a pin-on-disc wear testing machine in which nitrided pins were mated to hardened ball ...

Energy Technology Data Exchange (ETDEWEB)

Duplex-coating procedures consisting of plasma nitriding and Me-C:H hard coating lead to an improved performance of the devices because the Me-C:H coating is supported by the nitrided phase and, therefore, the `eggshell-effect` is avoided. Furthermore, this support leads to a higher load-bearing capacity of the thin film. Two standard procedures (classical high-pressure plasma nitriding and unbalanced magnetron sputtering of Ti-C:H) were performed subsequently to prepare the duplex coatings on X20Cr13 ferritic stainless steel. The corrosion resistance of the steel could be improved by nitriding at 450 C compared to the untreated ferritic substrate. The roughness is determined by the nitriding step. The weakest point of the coating is the transition zone between the nitrided and the untreated substrate and not the interface between the Ti-C:H coating and the nitrided substrate as shown by the Rockwell and scratch tests. The adhesion of the ...

Energy Technology Data Exchange (ETDEWEB)

In this study samples of AISI 4140 steel were pretreated by plasma nitriding and coated with two different physical vapour deposited coatings (TiN and TiAlN). A hardened AISI 4140 sample and a coated sample were also included in the investigation. To examine the influence of the nitrided zone on the performance of the coating-substrate composite, two different nitriding conditions - a conventional 25% N{sub 2} and an N{sub 2}-poor gas mixture - were used. The specimens were investigated with respect to their microhardness, surface roughness, scratch adhesion and dry sliding wear resistance. Wear tests in which the duplex-treated pins were mated to hardened ball bearing steel discs were performed in a pin-on-disc machine under dry sliding conditions. Metallography, scanning electron microscopy and profilometry were used to analyse the worn surfaces in order to determine the dominant ...

Energy Technology Data Exchange (ETDEWEB)

Gas quenching for the hardening of steel parts is a lower-pollution alternative to quenching in quenchants such as oil or salt. As the surfaces of the cooled parts remain clean after gas quenching, there is no need to wash them after heat treatment, which reduces the consumption of oils and detergents. The fire risk and ventilation requirements of oil quenching are eliminated. In addition, some trials have shown that gas quenching has a positive effect on distortion, representing a saving in finishing work and thus a reduction in costs. Today, gas quenching is used almost solely in vacuum furnaces. Quenching is normally performed in the same chamber as heating, which means that besides quenching the batch, the quenching system must also remove heat from the heating elements and insulation of the furnace. Previous trials performed by IVF have shown that gas quenching with helium of ball bearing and carburizing ...

Energy Technology Data Exchange (ETDEWEB)

A number of screening tests were performed to determine ion species that effectively reduce wear rates when implanted in four industrial steels. Ball bearing steel 100Cr6 (AISI 52100) showed a wear rate reduction by a factor of 20 when implanted with carbon dioxide to a dose of 5x10{sup 17} cm{sup -2} with a non-mass-separated ion beam and by a factor of {>=}20 when implanted with 5x10{sup 17} cm{sup -2} oxygen ions. For the ferritic and martensite steels X90CrMoV18 (AISI 440B, unhardened and hardened) also a strong wear reduction after implantation of oxygen ions was found. Co-implantation of aluminum and oxygen also reduces wear rates of X90CrMoV18, of S6-5-2 (AISI M2), and of 100Cr6, respectively. For comparison, thin oxide layers were grown in a low-temperature thermal oxidation process. These experiments also yielded reduced wear rates by a factor of 10. The surfaces were ...

International Nuclear Information System (INIS)

Neutron irradiation embrittlement of reactor pressure vessel (RPV) steels is one of the critical issues on aging management for long term operation of nuclear power plants. Mechanistic understanding of embrittlement is a key to accurate prediction of embrittlement, especially after long term operation where the mechanical test data are sparse. Since matrix hardening is the source of the embrittlement, we focus on matrix hardening of A533B bainitic pressure vessel steel. Bainitic matrix is composed of lath structure made by ferrite and carbides, therefore it is important to understand how this structure affects hardening behavior, and to understand irradiation response of each phase. As the typical dimension of lath structure of A533B is about one micron, nanoindentation technique is suitable for the estimation of hardening of each phase. MV ion accelerators were ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the experimental results of long-life solid lubricated ball bearings tested under high-vacuum of 10 exp -4 Pa, high-temperature of 300 C, and high-speed (9000 rpm) conditions. For full ball-type bearings, the thin soft metals, either Ag or Pb, which were coated on the races and balls, appeared to have good torque properties. However, the durability of such bearings was less than 300 hours. The transfer films from the lamellar solid MoS2 and metal composite retainers improved the torque and wear properties. For ceramic, i.e., silicon nitride, balls used with steel rings, wear occurred on the inner rings. All ceramic bearings with composite retainers showed improved torque and wear properties. 18 refs.

Energy Technology Data Exchange (ETDEWEB)

Stress-rupture strength tests were made of metal steam pipe (12Kh1MF steel) in various conditions, the original, after aging under laboratory conditions (580{degrees}C, 10,000 h), and after long service. It was shown that the more the steel is hardened by heat treatment or cold plastic working in the original condition, the less it hardens in creep. It was established that softening in creep of steel with a moderate yield strength is caused primarily by aging and with a high yield strength by pore formation.

International Nuclear Information System (INIS)

Assessments of the hardening and embrittlement of pressure vessel steels and welds as a function of neutron dose use trend curves derived from surveillance programs and accelerated irradiation data. A temperature dependent factor is incorporated for assessing vessel locations operating at different temperatures. As hardening and embrittlement arise from the sum of matrix damage and copper impurity precipitation, the influence of irradiation temperature on each process needs to be established. For irradiations performed below #approx# 300 C recent data shows that the dose-dependent growth of copper precipitates ceases at a mean diameter of about 2 nm that also corresponds to peak hardening and embrittlement by copper. For doses beyond this peak copper dose the property-dependence on irradiation temperature can be identified with that of matrix damage alone. An analysis of several experiments on plate ...

International Nuclear Information System (INIS)

The effects of key metallurgical variables on the low fluence hardening in a set of A533B model steels were evaluated over a wide range of irradiation temperatures. Above about 163 degrees C hardening increased with higher copper and nickel contents, as is typical of the pressure vessel operating regime around 290 degrees C. However, at 121 degrees C the hardening was generally lower and unaffected by copper and nickel variations. This observation of decreased hardening with lower temperature (e.g. an open-quotes invertedclose quotes temperature dependence) is tentatively attributed to a reduced contribution of copper precipitation. Tensile data for a set of commercial steels with a range of (uncontrolled) compositions also showed minimal sensitivity to copper variations at 121 degrees C. Unlike the hardness data no systematic reductions in the yield stress ...

British Library Electronic Table of Contents (United Kingdom)

This paper provides a physically-based engineering model to estimate radiation hardening of 9%Cr-steels under both displacement damage (dpa) and helium. The model is essentially based on the dispersed barrier hardening theory and the dynamic re-solution of helium under displacement cascades but incorporating a number of assumptions and simplifications [Trinkaus, J. Nucl. Mater. 318 (2003) 234-340]. As a result, the kinetics of the damage accumulation kept fixed, its amplitude is fitted on one experimental condition. The model was rationalized on an experimental database that mainly consists of 9%Cr-steels irradiated in the range of 50-600degreeC up to 50dpa and with a He-content up to 5000appm. The test temperature effect is taken into account through a normalization procedure based on the...

Energy Technology Data Exchange (ETDEWEB)

Ceramic ball bearings of silicon nitride are used for hard disk drive (HDD) spindle motors, to increase seed, reliability and memory capacity of the HDDs. Silicon nitride ceramics have advantages of lightweight, high strength and hardness over the conventional steel for bearings, but is expensive. A new process of high cost performance has been developed for mass production of the small-size ceramic balls. The company plans to apply these bearings to higher devices, e.g., servers, for the time being, and to expand the applicable areas, e.g., common devices and other small-size motors. The ceramic bearings have been developed jointly with Koyo Seiko Co. Ltd. (translated by NEDO)

International Nuclear Information System (INIS)

Generally, neutron, ion and electron Irradiations cause a substantial amount of hardening and significantly alter the deformation behavior of metals and alloys at relatively low irradiation temperatures. A radiation hardening is caused by the formation of microstructural defects such as dislocation loops, voids and precipitates under irradiation. Therefore, it is important to have a better knowledge of the irradiation induced microstructural defects under irradiation condition. As a part of the National mid- and long-term atomic energy R and D program, we are dealing with the radiation hardening behavior in Fe-Cr binary alloy. Fe-Cr binary alloy is a base alloy of Ferritic/Martensitic steel(F/M steel) planning to use for the Gen IV nuclear system. In this work, we investigated the radiation hardening and microstructural defect evolution in ion irradiated Fe-Cr ...

International Nuclear Information System (INIS)

A large matrix of simple alloys and complex commercial type steels was irradiated over a range of fluxes at 60 FC up to a fast fluence of about 3 x 10"2"2 n/m"2. Combined with data in the literature, these results show a negligible effect of flux on irradiation hardening in the range of 2 x 10"1"3 to 5 x 10"1"8 n/m"2-s. This observation lends indirect support to the proposal that the accelerated embrittlement in the High Flux Isotope Reactor surveillance steels was due to an anomalously high level of damage from gamma rays. A weak dependence of hardening on a number of elements, including copper, nickel, phosphorus, molybdenum and manganese, can be described by a simple empirical chemistry factor. Particular combinations of elements resulted in hardening differences of up to about 60% in the complex commercial type steels and up to about 100% in simple model ...

International Nuclear Information System (INIS)

A study is made into microhardness and structure of coatings on various system steels (37G2S, 25Kh5M, R6M5), obtained by ion nitriding in a low pressure (10"-"1 Pa) arc discharge plasma. A comparison of properties is accomplished for steels nitrided in an arc gas discharge and in a furnace. It is stated that ion-plasma nitriding in an arc gas plasma generator is an efficient method of alloy steels hardening which allows changing the structure and increasing the hardness of a surface layer up to rather great depth

International Nuclear Information System (INIS)

Simultaneous nitriding and ageing heat treatments of precipitation hardenable tool steel was carried out inside a DC-pulsed plasma nitriding reactor. A single heat treatment cycle was done, as the plasma nitriding and age hardening processes occur approximately at the same ranges of temperatures and times. Specimens of Cr-Ni-Mo-Al age hardenable steel, in the solubilized and solubilized and aged conditions, were tested. Plasma nitriding and ageing, carried out at 500 deg. C for times ranging between 2 and 8 h, increased the surface hardness up to 1000 HV, producing case depths between 100 and 200 #mu#m. The core hardness of solubilized samples increased from 30 to 39 Rockwell C after the plasma nitriding treatment proving the possibility of nitriding and ageing at the same treatment cycle. The pre-aged samples did not show any overageing after the simultaneous plasma nitriding and ...

Energy Technology Data Exchange (ETDEWEB)

The thermal contact resistance between balls and inner and outer rings of thermally steady space-use deep groove ball bearings was studied experimentally to verify the validity of the previously proposed calculation method for the resistance. The 440C stainless steel single row bearing was used for measuring its steady state temperature distributions in a vacuum environment under axial, radial and combined load conditions. As a result, the experimental results of the resistance well agreed with calculated ones under each load condition resulting in the sufficient validity at nearly the same surface roughness. It was necessary to apply a static equivalent radial load to calculation under the combined load that a contact angle is larger than the angle of resultant force dependent on both load components. In experiments under only radial load, measurement of outer ring temperatures was necessary at some points with no contact ...

Science.gov (United States)

A separation phenomenon occurring during the Charpy impact test of API X80 pipeline steels was investigated in the present study. A detailed microstructural analysis of fractured impact specimens showed that the band structure of bainite elongated along the rolling direction worked as prior initiation sites for separations, and that the number and length of the separations increased with the increasing volume fraction of bainite. In the steels having high work hardenability, tearing-shaped separations were found because the hammer-impacted region was seriously hardened during the impact test, which led to the reduction in the impact toughness. As the test temperature decreased, the tendency toward separations increased, but separations were not found when the cleavage fracture prevailed at very low temperatures. These findings suggested that the formation of bainite and secondary phases should be ...

International Nuclear Information System (INIS)

Tensile properties of reduced-activation 10Cr-30Mn austenitic steels with carbon levels from 0.003 to 0.55% were investigated over the temperature range from room temperature to 873 K after neutron irradiation in the Japan Materials Testing Reactor at 573 K to 8.5x10"2"2 n/m"2. Irradiation-induced increase in yield stress increased significantly with carbon concentration up to about 0.1% and it was constant above 0.1% carbon. A high density of dislocation loops with small (below 10 nm) and large (20-30 nm) sizes formed during irradiation. The high density, small loops caused a large irradiation hardening, while the large loops contributed only slightly to irradiation hardening. It was considered that carbon atoms formed the small loops together with irradiation defects. The deformation channeling was observed in the irradiated high carbon steels, 0.11 and 0.55% carbon, but not in the very low carbon ...

Wastenet

... It has 2x 15L bins: one for food waste, the other for recycling, which slide out on ball bearing steel runners. Both have plastic inner buckets that can be lifted out. Supplied with fixing brackets. To fit 30cm-wide cabinets Filed Under: Top Products Tagged With: bedroom, bins, drawers, drawersshelveskitchenbins, garden, home, homegardenbedroomstorage, John Lewis, kitchen, shelves, storage ...

International Nuclear Information System (INIS)

Simulation irradiation experiments were carried out to investigate the formation processes and contribution to hardening of radiation-induced features in low alloy steels. Medium Cu (0.12 and 0.16%) and low Cu (0.03%) A533B steels were irradiated with 3 MeV Ni ions and 5 MeV electrons, and in KUR at 290degC. Irradiated steels were examined by three-dimensional atom probe, positron annihilation, high-resolution transmission electron microscopy and hardness measurements. Electron irradiation caused almost the same hardening as KUR irradiation in medium Cu steels under almost the same dose rate and dose conditions, whereas the formation of larger, denser and more Cu enriched clusters and smaller accumulation of single vacancies were confirmed for KUR irradiation. This indicated that cascade damage provides additional cluster nucleation sites to compensate for lower ...

Energy Technology Data Exchange (ETDEWEB)

Hard surface finishing represents the final manufacturing step for functional areas of machine elements in state-of-the-art production. Raceways of rolling bearing rings are ground and honed to the required low roughness. Plastic deformation is restricted to a narrow edge zone of the hardened steel. Reheating of the machined components below the martensite tempering or bainite transformation temperature results in a marked decrease of the XRD line width on the surface. The investigated samples are made of through-hardened standard bearing steel 100Cr6 (international denotation: SAE 52100). On the basis of a material model that explains the effect as a complex diffusion process of dislocational carbon segregation, i.e. static strain aging, the measured kinetics of the XRD line width reduction is simulated by an Arrhenius-type equation, which describes the rate-controlling reaction step of temper carbide ...

International Nuclear Information System (INIS)

This paper provides a physically-based engineering model to estimate radiation hardening of 9%Cr-steels under both displacement damage (dpa) and helium. The model is essentially based on the dispersed barrier hardening theory and the dynamic re-solution of helium under displacement cascades but incorporating a number of assumptions and simplifications [Trinkaus, J. Nucl. Mater. 318 (2003) 234-340]. As a result, the kinetics of the damage accumulation kept fixed, its amplitude is fitted on one experimental condition. The model was rationalized on an experimental database that mainly consists of ?9%Cr-steels irradiated in the range of 50-600 deg. C up to 50 dpa and with a He-content up to 5000 appm. The test temperature effect is taken into account through a normalization procedure based on the change of the Young's modulus and the anelastic deformation that occurs at high temperature. Despite the large ...

Energy Technology Data Exchange (ETDEWEB)

The scope of the present article is two-fold. Firstly, to conduct an experiment to provide the temperature-time history of the cooling of a hot ball bearing in quiescent ambient air. Secondly, to predict the temporal variation of the bearing under the hypothesis of natural convection, radiation or natural convection coexists with radiation for a non-vanishing total hemispherical emissivity of the surface of the bearing. Numerical solutions of the three governing nonlinear lumped heat equations were carried out with a Runge-Kutta-Fehlberg (RKF45) algorithm accounting for automatic step size control. The experimental data was obtained with chrome steel ball bearings of diameter 0.953 cm (7/16 in) heated in an electric oven to a pre-set temperature. The heated bearing was exposed later to ambient air at atmospheric temperature and pressure. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This paper explains technologies for turbo chargers used in light cars. Light car engine turbo chargers have been given various improvements responding to needs of the market. Since ball bearings have less mechanical loss than sliding bearings, and enhances greatly the turbo efficiency, they are used in some high performance engines of light cars. While the conventional ball bearing has used high hardness bearing steel, the new standard cars started using ceramic ball. The currently used light car gasoline engines are divided into two kinds, serial three-cylinder type and serial four-cylinder type, either having merits and demerits. The new twin entry turbo developed by IHI arranges divided exhaust gas ports above and below to simplify the manifold shape, and realizes smooth flow by twisting the exhaust gas flow path inside the turbine housing. This makes the dynamic pressure of the exhaust gas more ...

Energy Technology Data Exchange (ETDEWEB)

Computed tomography (CT) has been incorporated in an industrial Diode-Array Digital Radiography (DADR) system. An input data size of 512 pixel points x 400 projections yielded a 400x400 output image matrix. Reconstruction algorithms used are the filtered backprojection (FBP) and the direct Fourier reconstruction (DFR). Various filters were used in the FBP reconstruction process and their effects on image quality were evaluated. A spatial resolution of 100 {mu}m was measured with a block of plates and a minimum detectable feature size in the range of 10-100 {mu}m was measured using thin wires. Industrial specimens imaged have included ceramic samples, ball bearings and integrated circuits. A number of engineering problems have been solved, such as adjustment of the X-ray source, centering of the rotator spindle in the view field and beam-hardening corrections. (orig.).

Energy Technology Data Exchange (ETDEWEB)

By characterising the microstructure, quantitative image analysis allows to draw conclusions on the mechanical properties of materials. On fine microstructures with low contrast, e.g. of hardened steels, texture analysis has to be applied for quantification. Feeding texture parameters according to Haralick into a trained neural network, a correlation between the microstructure and the hardness of the steels C45 and 100Cr6 can be achieved. (orig.)

International Nuclear Information System (INIS)

Radiation hardening in austenitic stainless steels is shown to modify deformation characteristics and correlate well with an increased susceptibility to intergranular stress corrosion cracking (IGSCC). Available data on neutron-irradiated materials have been analyzed and correlations developed between fluence, yield strength and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 to 2.5 x10"2"1 n/cm"2) for IGSCC are documented. In many cases, this variability is consistent with yield strength differences among irradiated materials. IGSCC correlates better to yield strength than to fluence for most heats suggesting a possible role of radiation-induced hardening and microstructure on cracking. Microstructural evolution during proton and heavy-ion irradiation has been characterized in low-carbon 304SSs. Hardening results from a ...

British Library Electronic Table of Contents (United Kingdom)

The purpose of this study is to investigate the influence of tungsten carbide/carbon (WC/C) coating on the surface durability of casehardened steel gear. Two kinds of WC/C coatings were deposited on the ground gear pair made of chromium molybdenum steel with carburizing and quenching. One is the conventional WC/C coating, and the other is WC/C coating with about 1 ?m CrN interlayer. Here, the WC/C-coated test pinion and the WC/C-coated one with CrN interlayer are represented by WT and ST, respectively. Non-coated test pinion is represented by NT. The surface roughness along the tooth profile direction of WT and ST was almost the same as that of NT. A spur gear test was carried out with an IAE power circulating type gear test rig under EP gear oil lubricating condition. The fatal failure mo...

International Nuclear Information System (INIS)

Early failure of an induction-hardening carbon steel pipe, which was used to transport tailing slurry, was caused by pitting corrosion. The microstructure on the internal pipe surface layer was found being a mixture of martensite, pearlite and ferrite. In this work, the pitting corrosion behavior of each constitute in the microstructure of steel is investigated with electrochemical noise analyses; the electronic properties of passive films were studied with Mott-Schottky relationship. It is found that the passive films formed on the materials under investigation are highly disordered n-type semiconductors. The high-to-low pitting susceptibility is ferrite > martensite > pearlite. The pitting resistance is related to the semiconductive nature of the passive film formed on each constitute. The pitting susceptibility increases with the donor concentration in the passive films. (author)

Energy Technology Data Exchange (ETDEWEB)

The authors obtain the critical load levels corresponding to the onset of spalling microdamage for Armco iron and steels St.3 and 12Kh18N10T in a broad temperature range (-196-800 degrees C. The results of the investigation of the effect of the temperature on spalling fracture are presented. The effect of the loading time on the strength of the investigated materials is also given. The authors assume that at -196 degrees C impact-wave strain-hardening may also be characterized by the value of H obtained for the center of the specimen since measurements on great thicknesses, including those reaching as far as the opposite surface, did not reveal any substantial change of microhardness.

Energy Technology Data Exchange (ETDEWEB)

This report describes work accomplished in the project, titled ''Development of Appropriate Resistance Spot Welding Practice for Transformation-Hardened Steels.'' The Phase 1 of the program involved development of in-situ temper diagrams for two gauges of representative dual-phase and martensitic grades of steels. The results showed that tempering is an effective way of reducing hold-time sensitivity (HTS) in hardenable high-strength sheet steels. In Phase 2, post-weld cooling rate techniques, incorporating tempering, were evaluated to reduce HTS for the same four steels. Three alternative methods, viz., post-heating, downsloping, and spike tempering, for HTS reduction were investigated. Downsloping was selected for detailed additional study, as it appeared to be the most promising of the cooling rate control methods. The ...

Energy Technology Data Exchange (ETDEWEB)

PVD-chromium-nitride coated samples of substrates of the magnesium alloy AZ91hp and the roller and ball bearing steel 100Cr6 were investigated regarding structure, mechanical characteristics, adhesion and internal stresses. For the coatings the parameters layer thickness and substrate BIAS voltage were varied. Both substrate materials were coated in one lad. Results of the X-ray analysis of the internal stresses show significant differences between the coated magnesium and the coated steel substrates. In the case of the variation of the substrate BIAS voltage, for the coated steel a dependency of the internal stresses to coating parameters could be obtained. For the coated magnesium no dependency was recognizable. The coating structure was examined with scanning electron microscopy. Element depth profiles of the coated samples were performed with SIMS. (orig.)

Energy Technology Data Exchange (ETDEWEB)

By using a plasma nitriding procedure at the PUPR Mirror Cusp Plasma machine, surface hardness is increased in 302/304-type stainless steel samples by exposing them to high-ion-density plasma at high vacuum. This method successfully dopes the surface of the material with strengthening nitrogen ions, without the use of chemical procedures that sacrifice the resistance to corrosion of the given material. A 500 V negative bias is placed on the sample exposed to the nitrogen plasma, where high-energy ions are therefore attracted and immersed into the metallic matrix microns into the surface of the stainless steel. This potential maintains a constant surface temperature at approximately 800 deg. C. The plasma parameters including ion density and plasma temperature were diagnosed using single Langmuir probes. The stainless steel samples were then tested using scanning electron microscopy (SEM), and Vickers micro-hardness testing ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to describe the processes during plasma nitriding of Nb-containing, powder metallurgy prepared (PM) tool steel. PM steel was studied containing 2.5% C, 3.3% Si, 6.2% Cr, 2.2% Mo, 2.6% V, 2.6% Nb and 1.0% W, produced by melt atomization and hot isostatic pressing. The hardened and tempered steel was plasma nitrided at temperatures ranging from 470 to 530 deg. C. The nitriding time was 30-180 min. Optical microscopy, electron microscopy, XRD, EDS, WDS and hardness measurements were used to study the steel's properties, microstructure, phases and chemical composition. The nitriding temperature of 470 deg. C was found to be unsuitable for practical use because the layers prepared at this temperature were non-uniform. The compound layer formed by M{sub 2,3}(C,N) and M{sub 4}N was found after nitriding at temperatures of 500 and 530 deg. C for at least 60 ...

Energy Technology Data Exchange (ETDEWEB)

Spray depositing allows the production of steels having a structure which is free of any macro-segregation, homogeneous and equiaxed. Nevertheless the spray deposition of steels shows some effects that have to be regarded as disadvantages. A porous region at the billet border and a rather coarse-grained microstructure can be noticed. As a result, in the presented work the influence of a subsequent hot rolling and a following heat treatment on microstructure and mechanical properties has been investigated. For this purpose the bearing steel SAE 52100 has been used as master material. The initial microstructure has been transformed to a homogeneous equiaxed fine-grained pearlitic microstructure without any remaining porosity. To get use of the characteristic properties of this high-strength steel an isothermal bainitic hardening has been carried out. Information about the mechanical ...

International Nuclear Information System (INIS)

Yield stress elevations (#DELTA##sigma#_y) in pressure vessel steels irradiated at intermediate flux and fluence systematically decreased with increasing temperature and decreasing copper and nickel content. Lower stress relief temperature also decreased #DELTA##sigma#_y at bulk copper concentrations greater than about 0.3%. The dependence of #DELTA##sigma#_y on irradiation temperature between 260 and 316 C increased with copper and nickel content and decreased with phosphorus content. When normalized by the average #DELTA##sigma#_y, the fractional temperature dependence correlates with a simple empirical chemistry factor of copper and phosphorus. The correlation predicts data on the irradiation temperature dependence of #DELTA##sigma#_y found in the literature within a standard error of about 0.3 MPa/degree C and is consistent with current understanding of hardening mechanisms. However, questions remain about the effects at very low flux and ...

Energy Technology Data Exchange (ETDEWEB)

Alloyed steels containing retained austenite after martensitic hardening are widely applied in technical practice. Although many practical investigations have been made into the mechanical behaviour of composite microstructures with retained austenite, there is still a lack of knowledge concerning their fatigue and crack propagation behaviour. For this reason, the author investigated the effects of retained austenite concentration and stability on the transformation and deformation behaviour of hardened states of the steels X210Cr12 and 100Cr6. For this purpose, monotone tensile tests, cyclic tensile pressure tests, and supplementary crack propagation experiments were carried out. The concentrations of retained austenite were varied between 10 and 100% by volume by means of different heat treatments. [Deutsch] Legierte Staehle, die nach martensitischer Haertung noch Restaustenit enthalten, finden in der ...

International Nuclear Information System (INIS)

A post-irradiation annealing study was conducted with use of reactor pressure vessel(RPV) steel A533B C1.1 base metal irradiated to a dose of 4.84x10"1"8 n/cm"2 at about 380 deg C. Microhardness and positron annihilation (PA) methods were used to obtain better understanding of the recovery of radiation hardening. Isochronal anneal experiments indicated that two recovery processes occur during annealing of irradiated specimens. The first recovery process occurs in the temperature of 280-305 deg C. The variations of Ip, Iw and R parameters indicated that the formation of vacancy clusters by vacancy aggromeration and the annihilation parameters measured indicated that the dissolution of carbon atoms decorated around vacancy-type defects and possible precipitates, and the annihilation of monovacancies give rise to the second recovery process. It was further indicated that radiation anneal hardening (RAH) in the range of 305-405 ...

Energy Technology Data Exchange (ETDEWEB)

The present conference discusses plasma-assisted surface coating/modification processes, the applications to date of ion nitriding, the effects of nitrogen on metal surfaces, ion nitriding mechanisms in Cr, Al and Cr + Al-containing 1040 steel, ion nitriding of Al and its alloys, life enhancement for forging dies, novel anode plasma nitriding developments, and a comparative study of the pulsed and dc ion-nitriding behavior in specimens with blind holes. Also discussed are the influence of heating method on ion nitriding, surface hardening of marage steels by ion nitriding without core hardness reduction, plasma nitriding of nodular cast iron sput gears, NbN composites for superconductors, the carburization of tungsten in a glow discharge methane plasma, economic considerations concerning plasma nitriding, and the corrosion properties obtained by ion nitriding.

Energy Technology Data Exchange (ETDEWEB)

Microhardness decarburization profiles are often used in the industry to estimate the carbon distribution in steels. For quantitative evaluation, an analysis based on diffusion theory must be performed, the fundamentals and mathematical basics of which are presented. If the relationship between hardness and carbon content is known, microhardness-distance curves of steels can be analyzed in this way. For martensitic grades, for instance, a linearized expression holds in the concentration range from 0.15 to 0.6 m.% C. Microhardness depth profiles of higher carbon steels and other microstructures, however, are also evaluated in the literature. The applicability of quantitative diffusion modeling is discussed in detail. Through hardenable rolling bearing steel 100Cr6 (1.3505, SAE 52100) serves as model material: carbon concentration-distance curves are measured with high accuracy by ...

Energy Technology Data Exchange (ETDEWEB)

Determination of stacking fault energy (SFE) of the austenite phase of a duplex stainless steel DIN W.-Nr.: 1.4462 has been carried out using transmission electron microscopy. Furthermore, cold rolling tests and microstructural analysis have been realized in order to allow a detailed discussion of the obtained SFE-values. The results of this investigation indicate that the stacking fault energy of the austenite phase within the duplex stainless steel is lower than of one-phase austenitic stainless steels. This is justified by the chemical composition, mainly by the Cr and Ni alloying contents. Nevertheless, work hardening of the austenite during cold deformation is not as accentuated as expected by the SFE-values, because at higher deformation levels the deformation mainly occurs within the ferrite phase 7 refs., 5 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The effect of partial and total replacement of tungsten by molybdenum on the mechanical technical properties were investigated with the cold work steel 60 WCrV 7 (DIN 1.2550). While maintaining the total quantity of tungsten atoms and/or molybdenum atoms in the steel, no differences occur in the type of the separated carbides. After annealing in the range of the pearlite stage with annealing times of up to 150 h, the carbide phases M/sub 23/C/sub 6/ and MC are, besides alpha iron, also present. In short-time annealed states also M/sub 6/C carbides occur. These are formed during austeniting and remain in the steel as residual carbides in austeniting treatment carried out under normal conditions. Compared with tungsten alloyed steel, there is an increased formation of M/sub 6/C carbides in molybdenum alloyed steels during austeniting. By a long-time annealing treatment in the range of ...

Energy Technology Data Exchange (ETDEWEB)

A duplex surface treatment technique based on calorizing and plasma nitriding was developed to improve the wear and oxidation resistance of H13 steel at high temperatures. The effects of the relative thickness of the calorized layer to the depth of plasma nitriding on the wear and oxidation properties at temperatures up to 900 C were investigated in this work. High-temperature wear tests were performed at 500 C with dry conditions in open air using a ball-on-disk type tribotest machine. Isothermal oxidation tests were performed at 900 C for up to 100 h under controlled atmosphere. The results indicated that the specimens with a calorized layer as an intermediate phase between the surface duplex layer and the base metal showed higher wear and oxidation resistance than the specimens with a nitrided layer alone. During exposure to elevated temperatures, the aluminum in the calorized layer diffused to the surface and formed an aluminum oxide layer. ...

Science.gov (United States)

... Accession Number : AD0164404. Title : Ball and Roller Bearing Retainer Improvement for High Speed Operation. Descriptive Note : Patent,. ...

International Nuclear Information System (INIS)

Thermo-reactive diffusion chromizing followed by pulsed plasma nitriding were carried out on AISI 52100 and 8620 bearing steels. The chromized samples were pulse-plasma nitrided for 5 h at 500 deg. C in various N_2-H_2 gas mixtures. The coated steels were characterized using scanning electron microscopy, X-ray diffraction and microhardness testing. The unlubricated wear behaviors of only chromized and duplex treated steels were investigated in ball-on-disc system tests at room temperature. X-ray diffraction patterns of the duplex treated samples containing H_2 indicated the formation of dominant CrN and Cr_2N nitrides as well as the formation of Cr_3C_2 and Cr_7C_3 carbides. Gas mixtures in the plasma nitriding, which was performed after chromizing, have a significant influence on the wear rate of the duplex treated steels. The wear and friction tests showed that the lowest friction ...

International Nuclear Information System (INIS)

For an assessment of the future US spallation neutron source (SNS) target performance, radiation induced hardening and microstructural evolution were investigated as a function of ion dose for EC316LN stainless steel. Irradiation was carried out using 3.5 MeV Fe"+, 360 keV He"+, and 180 keV H"+ simultaneous ion-beams at 200 deg. C to simulate the damage, He and H production in the SNS target vessel wall. At low dose (< 1 dpa), the predominant defects were black dots whose number density saturated rapidly within a few dpa. This was followed by the evolution of interstitial loops whose number density saturated below 15 dpa. Although He-bubbles were not visible, severely scalloped loops suggested that the implanted He/H atoms existed in the form of small clusters. Comparison with reported neutron irradiation data showed that hardening and ductility loss occurred mostly in the black dot regime (< 1 dpa), but that good ...

Science.gov (United States)

... Accession Number : ADD100229. Title : DEFORMATION BEHAVIOR OF AN OMEGA HARDENED ALPHA-BETA TITANIUM ALLOY,. ...

International Nuclear Information System (INIS)

Post-irradiation annealing was used to help identify the role of radiation-induced segregation (RIS) in irradiation-assisted stress corrosion cracking (IASCC) by preferentially removing dislocation loop damage from proton-irradiated austenitic stainless steels while leaving the RIS of major and minor alloying elements largely unchanged. The goal of this study is to better understand the underlying mechanisms of IASCC. Simulations of post-irradiation annealing of RIS and dislocation loop microstructure predicted that dislocation loops would be removed preferentially over RIS due to both thermodynamic and kinetic considerations. To verify the simulation predictions, a series of post-irradiation annealing experiments were performed. Both a high purity 304L (HP-304L) and a commercial purity 304 (CP-304) stainless steel alloy were irradiated with 3.2 MeV protons at 360 deg. C to doses of 1.0 and 2.5 dpa. Following irradiation, post-irradiation ...

Energy Technology Data Exchange (ETDEWEB)

Problems can sometimes occur during the construction of cast in-situ concrete piles. These foundations are formed by drilling a substantial hole into the ground and subsequently filling it with steel reinforcement and wet concrete. Several well-documented cases exist where concrete has not filled the hole and substantial voids have been left in the apparently completed pile. A theory has been developed by which it is possible to identify the nature, size and position of a finite defect within a suspect pile. The technique is based on the concept of receptances, and requires information obtained from vibration tests performed on piles after the concrete has hardened, and the nominal dimensions and material properties of the pile. The application of the theory is demonstrated using data relating to a pile with a known defect. The theory described in this paper ignores the effect of the surrounding soil; this can be included by further development ...

Energy Technology Data Exchange (ETDEWEB)

The topics of these short lectures on the subject of cyclic stress were: Microstructural mechanisms of damage accumulation under a multistage cyclic stress until incipient cracking; influence of surface decarbonizing phenomena on the failure behaviour of steel construction parts subjected to cyclic stress; thermocyclic fatigue of pipe samples of austenitic steel 1.4436; studies on surface structuring, microstructure and fatigue in LCF area. The short lectures on effects of quasi-static and creep stress were: Shear fracture in AlMg alloys as a result of local plastic instability; study of formation and growth of pores for an early recognition of damage and the course of damage in heat-resistant steels under creep test; experimental and numeric studies of the infuence of the microstructure on the course of damage during shear fractures of steel; numerical modelling of ductile fractures on the basis of ...

International Nuclear Information System (INIS)

In 1998, in the frame of the ITER EDA phase, an European R and D Programme for the Blanket Design was implemented for developing and selecting the materials and the relevant fabrication procedures for manufacturing the shielding modules of the ITER Primary Wall. The fabrication of several Beryllium armored small scale mock-ups, reproducing representative portions of a Primary Wall panels, was also launched (Fusion Technol. (1998) 195). Further experimental activities were also programmed for investigating the thermal-mechanical behavior of these mock-ups at high heat flux and under thermal fatigue tests. In 2001, the ITER European Home Team decided to assign to ENEA a contract for the thermal fatigue testing of six mock-ups aiming at verifying the reliability of the Beryllium/Dispersion Strengthened Copper alloy/Stainless Steel and Beryllium/Precipitation hardened Copper alloy/Stainless Steel joints manufactured by solid ...

International Nuclear Information System (INIS)

As a hardening process, the attractiveness of nitriding lies in its low treatment temperature. Although the thickness of the case is less than that obtained by higher temperature processes such as carburising, there are a range of alloys and applications for which nitriding is the only possible alternative. Indeed, there are some alloys and applications for which even the normal nitriding temperatures (between 500 deg C and 600 deg C for ferrous alloys) are too high. In this paper, we report on developments, specifically the use of low pressure plasmas and high energy ion bombardment, which can extend the benefits of nitriding to lower temperatures. In this poster, we will present results from these collaborative projects, concentrating on the nitriding of austenitic stainless steel at temperatures below 450 deg C. In this temperature range, the hardness and wear resistance of the surface can be improved without compromising the corrosion ...

Energy Technology Data Exchange (ETDEWEB)

Tensile specimens of the normalized and tempered fully martensitic steel DIN 1.4914 were helium implanted up to 340 appm within the temperature range 300-720/sup 0/C using a 104 MeV alpha particle beam. The high He/damage ratio of 1850 appm He/dpa allowed to determine the effect of helium on material properties. After irradiation tensile strength and ductility were investigated mainly at test temperatures equal to the irradiation temperatures. While short time irradiations with helium contents up to 100 appm have shown no visible effect on the tensile behaviour at all temperatures investigated, long time irradiations reduced the material strength at irradiation temperatures above about 440/sup 0/C. This irradiation induced softening obscured the predicted minor hardening effect of the observed He-bubbles completely and increases with irradiation time and temperature. The fracture mode of helium-implanted and control specimens is found to remain ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties of Fe-Mn-Al alloys; passive films formed on nonmagnetic Cr-Mn-N stainless steels in ...

Energy Technology Data Exchange (ETDEWEB)

To simulate radiation damage under a future Spallation Neutron Source (SNS) environment, irradiation experiments were conducted on a candidate 9Cr-2WVTa ferritic/martensitic steel using the Triple Ion Facility (TIF) at ORNL. Irradiation was conducted in single, dual, and triple ion beam modes using 3.5 MeV Fe{sup ++}, 360 keV He{sup +}, and 180 keV H{sup +} at 80, 200, and 350{degrees}C. These irradiations produced various defects comprising black dots, dislocation loops, line dislocations, and gas bubbles, which led to hardening. The largest increase in hardness, over 63 %, was observed after 50 dpa for triple beam irradiation conditions, revealing that both He and H are augmenting the hardening. Hardness increased less than 30 % after 30 dpa at 200{degrees}C by triple beams, compatible with neutron irradiation data from previous work which showed about a 30 % increase in yield strength after 27.2 dpa at 365{degrees}C. ...

International Nuclear Information System (INIS)

This paper consists of shielding analysis of steel balls and water filled end shields of Indian Pressurized Heavy Water Reactors (PHWRs). The material composition inside lattice tube is entirely different neutronically as compared with the composition of end-shield. Due to variation of material composition in radial and axial directions and complex geometry, it is necessary to carry out 3-D analysis for reasonable prediction of neutron flux and gamma dose rates. In the present paper, shielding analysis of end-shield for 540 MWe PHWR has been carried out during reactor operating and shutdown conditions using Monte-Carlo code MCNP. Furthermore materials on the periphery and central portion of end shield are different. Therefore the analysis was carried out separately for annular portion and central portion of end shield. The dominating streaming paths through end shields were studied. Predictions compare well with the measurements at TAPS-4 ...

Energy Technology Data Exchange (ETDEWEB)

There is an increasing number of applications for hard coatings in engineering where the properties of the single-layer coating are not sufficient. One way to solve this problem is to use a multilayer coating that combines the properties of several coating materials. In this study, TiN-CrAlN and CrN-CrAlN multilayer coatings were deposited on 100Cr6 and S6-5-2 (DIN) steel substrates, by means of unbalanced magnetron sputtering. For comparison, TiN, CrN and CrAlN single-layer coatings were also prepared. For all depositions the coating temperature was below 473 K. Indentation testing, hardness measurements and scratch tests were performed to characterize the mechanical properties. The correlation between the wear behavior in rolling contact and the mechanical properties of the multilayer coatings is reported. A ball crater preparation technique through scratch tests and wear tracks was used to observe the deformation and fracture behavior ...

International Nuclear Information System (INIS)

The Loose Parts Monitoring System (LPMS) provides information on the location of a loosened or detached metal impacted onto the inner surface of a primary pressure boundary and on a mass or energy of the impact signal. For the conventional system, it is popular to employ the group delay among the sensors installed within 3 ft range from the impact source in a collection zone as stated in the Reg. Guide 1.133. However, there exist inherent errors for the estimation of the true location of the impact since it is highly dependent on the plant personnel's decision to determine the arrival time differences of the generated wave group among the neighbouring sensors. To overcome this problem in this study, the two-dimensional approach has been proposed and applied to effectively estimate the arrival time differences of the impact signal by using continuous wavelet transform which is one of the linear time-frequency analysis methods. The experiment has been implemented on the plate model and ...

International Nuclear Information System (INIS)

Conventional plasma carburizing or nitriding for austenitic stainless steels results in a degradation of corrosion resistance. However, a low temperature plasma surface treatment can improve surface hardness without deteriorating the corrosion resistance. The 2-step low temperature plasma processes (the combined carburizing and post nitriding) offers the increase of both surface hardness and thickness of hardened layer and corrosion resistance than the individually processed low temperature nitriding and low temperature carburizing techniques. In the present paper, attempts have been made to investigate the influence of the introduction of Ar gas (0#approx#20%) in nitriding atmosphere during low temperature plasma nitriding at 370 .deg. C after low temperature plasma carburizing at 470 .deg. C. All treated specimens exhibited the increase of the surface hardness with increasing Ar level in the atmosphere and the surface hardness value reached ...

Energy Technology Data Exchange (ETDEWEB)

High-strength, fully hardening steels are used in general for applications involving severe wear and frequently also additional cyclic stress. For the latter condition, the available information and experimental data for component dimensioning are insufficient. Work reported in the dissertation therefore was intended to establish experimental information showing the performance of the bainitic roller bearing steel 100Cr6 and deducing rules of applicability to components, of the fatigue strength data obtained with the specimens. Various models for calculating the fatigue strength are presented together with their application to the steel 100Cr6. The results show that the weakest link model is a good concept for fatigue strength calculation, taking into account multiaxial loading. (orig/CB) [Deutsch] Hochfeste durchhaertende Staehle unterliegen in der Regel hohen Verschleissbeanspruchungen und werden ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The model of the supersymmetrical ball in the supersymmetrical Standard Model with additional global U(1) fermion symmetry is presented. We show that the supersymmetry breaking scale (R-parity), the global U(1) fermion symmetry scale and the electroweak symmetry breaking scale are strictly connected to each other. The realistic ball with M[approx]10[sup 5]-10[sup 9] M[sub s]un and the radius R[approx]10[sup 12]-10[sup 14] cm is obtained. Inside the ball all full symmetries are restored. The ball is stabilized by superpartners and right neutrinos which are massless inside. (orig.)

International Nuclear Information System (INIS)

Short communication.

International Nuclear Information System (INIS)

... defects doped materials germanium infrared radiation monocrystals neutron

Energy Technology Data Exchange (ETDEWEB)

Graphite fluoride (CF{sub x}) is investigated as an additive for WS{sub 2} thin films to reduce its sensitivity to moisture. The films are grown onto hardened 440C stainless steel disks by pulsed laser deposition using the 248 nm line from an excimer laser. Substrate temperature and additive concentration are varied to control film chemistry and crystal structure. The effect of relative humidity (i.e., < 1 to 85% RH) on friction is evaluated. Coatings grown at RT from targets with a low concentration of CF{sub x} exhibit ultra-low friction (ULF) behavior in dry air (i.e., {mu} {<=} 0.01), but friction increases with RH. Mechanisms for the ULF behavior are proposed which suggest that further reductions in friction are possible. Films grown at 300 C or with higher concentrations of CF{sub x} are relatively insensitive to humidity, but have more typical friction coefficients ({mu} {<=} 0.04) in dry air. (orig.)

International Nuclear Information System (INIS)

NaCl doped MgCl_2.nEtOH adducts were prepared by ball-milling MgCl_2.2.5EtOH with NaCl. Both the ball-milled MgCl_2.nEtOH/NaCl mixture and pure MgCl_2.2.5EtOH adducts were analyzed by X-ray diffraction (XRD), transmission electron microscope (TEM), thermogravimetry (TG) and differencial scanning calorimetry (DSC). A simple MgCl_2.nEtOH/NaCl mixture without ball-milling treatment was also studied for comparison. Two kinds of mixed crystals, Na_2MgCl_4 and NaMgCl_3, were found to be formed in a ball-milled mixture that contained 16 mol.% NaCl. TG and DSC analysis of the samples also provided indirect evidences supporting the presence of the mixed crystals in the ball-milled mixture. Adding certain amounts of NaCl in MgCl_2.2.5EtOH adduct, either by co-milling or by simple mixing, greatly increased the thermal stability of the adduct, but thermal decomposition behaviour of the ...

Energy Technology Data Exchange (ETDEWEB)

The influence of a decarburisation process during austenitising of the through-hardenable rolling bearing steel 100Cr6 (SAE 52100) on the rim zone properties of the martensitic through-hardened material was investigated by means of material analysis and diffusion calculations. For this purpose, two specimens were prepared under defined heat treatment conditions, and the near-surface carbon distribution was determined micro-chemically by using secondary ion mass spectrometry (SIMS). In part 1 of the present work, these concentration profiles are compared with the depth variation of the micro-hardness and with the distance curves of the residual stresses and the line broadening ({l_brace}211{r_brace} {alpha}'-Fe diffraction line) both measured by X-ray diffraction (XRD). In addition, microstructure investigations were performed. In part 2, a refined kinetics model of a diffusion-controlled reaction based on the ...

International Nuclear Information System (INIS)

The radiation hardening studies started in the mid decade 1960-1970. To survive the different military or space radiative environment, a new engineering science was born, to understand the degradation of electronics components. The different solutions to improve the electronic behavior in such environments have been named 'radiation hardening' of the technologies. Improvement of existing technologies, and qualification methods have been widely studied. However, on the other hand, specific technologies were developed: the Silicon On Insulator technologies for CMOS or Bipolar. The HSOI3HD technology offers today the highest hardening level for the integration density of hundreds of thousand transistors on the same silicon. Full complex systems could be produced on a single die with a technological radiation hardening and no more system hardening.

Energy Technology Data Exchange (ETDEWEB)

The structure and pore morphology, the isothermal and continuous time-temperature conversion characteristics and the effects of heat treatment on the mechanical properties and microstructural processes were investigated in 4 copper-free recycleable PM steels Fe4Ni0,5Mo+0,5%C ({rho}=7,12 g/cm{sup 3}, HT-sintered), Fe4N0,5Mo+0,7%C ({rho}=7,12 g/cm{sup 3}, sinter-hardened), Fe1,5Mo+0,5%C and Fe1,5Mo+0,5%C+0,5%CEP ({rho}=7,3 resp. 7,32 g/cm{sup 3}, HT-sintered). [German] In dieser Arbeit wurden an den vier kupferfreien rezyklierfaehigen PM-Staehlen Fe4Ni0,5Mo+0,5%C ({rho}=7,21 g/cm{sup 3}, hochtemperaturgesintert), Fe4Ni0,5Mo+0,7%C ({rho}=7,12 g/cm{sup 3}, sintergehaertet), Fe1,5Mo+0,5%C und Fe1,5Mo+0,5%C+0,5%CEP ({rho}=7,3 bzw. 7,32 g/cm{sup 3}, hochtemperaturgesintert) die Gefuege und die Porenmorphologie, das isotherme und kontinuierliche Zeit-Temperatur-Umwandlungsverhalten, sowie der Einfluss verschiedener Waermebehandlungen auf die ...

Energy Technology Data Exchange (ETDEWEB)

It is suggested that the model of a neutrino ball described in terms of the standard model extended by adding right-handed neutrinos and the Majorana scalar field can be presented in order to explain a body of weak interacting neutrinos. Neutrino interaction with the scalar Majorana field violates the lepton number and produces the mass splitting of neutrino due to the sea-saw mechanism. In this model a neutrino ball is an object which appears as a result of a first order cosmological phase transition. It can be regarded as a ball filled with Dirac neutrinos and can be treated as a remnant of the phase transition with unbroken global lepton symmetry. In this paper we study the macroscopic parameters of such a configuration. In the result the mass-radius curve M(R) for this object is obtained. (orig.).

International Nuclear Information System (INIS)

This talk sketches out the main parameters (technology, circuit design) that have an influence on the hardening of digital CMOS integrated circuits. For each technology the more common defects are mentioned. General design rules are proposed to prevent or limit those defects. (D.L.). 2 refs., 2 figs.

International Nuclear Information System (INIS)

This paper addresses the background and the continuously evolving topics of hardening and electronic components. Typical radiation environments from 1960 are described. Examples of a civilian satellite and of future particle physics colliders help illustrate hardening problems. Effects in components, limits of shielding, and three methods of providing components are described. The authors conclude by focusing on both future trends of radiation environments and anticipated progress in electronics. (authors). 10 refs., 9 figs., 4 tabs.

International Nuclear Information System (INIS)

A program was undertaken to radiation harden an existing power integrated circuit technology (BCDMOS) to total dose, gamma dot, SEU, and neutrons. Efforts have centered around hardening and optimizing our CMOS, DMOS, and NPN devices. Initial results indicate a substantial improvement in hardness over our existing commercial technology.

International Nuclear Information System (INIS)

The Guarantee Outline presents the technical demands of design and contents of assessment for radiation hardening in satellite engineering in China. It includes the basis of design in space environment of polar orbit, the contents of design for general radiation hardening, the requirements and assessments of the single-board computer, the requirements of design for circuits (including hardware and software), the choices and assessments for devices, and the primary stipulations for the requirements of design and assessments against the phenomenon of charge and discharge.

International Nuclear Information System (INIS)

This paper reviews various techniques to harden Charged Coupled Device (CCD) sensors and the results after irradiation of three Thomson n buried channel CCDs having a different degree of hardening. It describes the major irradiation effects on CCD performances and it makes a comparison of the results between the different hardening levels. It shows good results on dark voltage after ionizing radiation for TH 7863M device hardened both by design and by operating conditions (MPP mode) with respect to the standard device TH 7863A. The irradiations were performed with "6"0Co or X-ray (10 keV) sources on devices in operating mode. (author). 3 refs., 8 figs.

Energy Technology Data Exchange (ETDEWEB)

Ball screw bearings are used for the fine control of Control Rod Drive Mechanism (CEDM) for the SMART-P. Because the friction coefficient of the ball screw bearings suddenly increases at the limit temperature of 120 .deg. C, the surrounding temperature of the ball screw bearings should be less than the limit temperature for the functional integrity of the CEDM. The CEDM coolers are installed at the lower portion of the ball screw bearings to maintain the bearings' temperature less than the limit. In order to check the CEDM cooler satisfy the temperature limit of ball screw bearing at the possible operational conditions, the cooling capacity of the CEDM coolers, which was determined at the stage of 'conceptual design', is evaluated using the Computational Fluid Dynamics(CFD) code, Fluent. The analysis result shows that the current CEDM coolers satisfy the ...

CERN Document Server

Structural steels with improved atmospheric corrosion resistance

International Science & Technology Center (ISTC)

Investigation of Destruction Mechanisms in Reactor Steels and Alloys under Cycling Deformation

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

Mechanical properties of P-LDHA and V-ROL N steels of the Czech production are compared with other ultra-high strength steels produced in the world. The most important results can be summarized into following points: 1. Optimally heat treated P-LDHA steel exhibits substantially better strength characteristics then the V-ROL N steel. 2. Optimal tempering temperature of the P-LDHA steel is 300 C. 3. Basic mechanical properties of P-LDHA steel belong to the top of the UHS steels ranking and are well comparable with those of American 300 M steel. 4. In the low-cycle fatigue region, the P-LDHA steel exhibits slightly better fatigue resistance then the 300 M steel. On the other hand, the high-cycle fatigue resistance of 300 M steel is slightly better then that of ...

International Nuclear Information System (INIS)

The forced nonlinear vibration and its stability of a single-degree-of-freedom system with a ball screw type damper which is composed of a ball screw, a flywheel and a flyball governor are discussed theoretically. The results are compared with a linear solution and the experimental results. The effect of vibration isolation of the damper is also discussed. Numerical examples are given for several ratios of the natural frequencies in the primary system to the governor. It is demonstrated that, when the natural frequency ratio is chosen suitably, the damper is effective in suppressing the resonance of the primary system. The amplitude response curve of the primary system is approximately equal to the linear solution except in the vicinities of the natural frequencies of the primary system and the governor, and is stable except in the vicinity of the natural frequency of the governor. (author).

British Library Electronic Table of Contents (United Kingdom)

Medium-density polyethylene/multiwall carbon nanotube (MDPE/MWCNT) nanocomposites were produced by a mechanical milling method using a high-energy ball mill. The MDPE and MWCNTs were added to the ball mill at a constant 20:1 weight ratio of ball/powders and milled for 10 h to obtain polyethylene matrix nanocomposites reinforced with 0.5, 1, 2.5, and 5 weight percent of MWCNTs. To clarify the role of both MWCNT content and milling time on the morphology of MDPE, some nanocomposite samples were investigated by using a scanning electron microscope. To evaluate the role of milling on the microstructure of the nanocomposites, very thin films of MDPE/MWCNTs were prepared and studied by transmission electron microscopy. Thermal behavior of these nanocomposites was investigated by using differenti...

International Nuclear Information System (INIS)

High temperature deformation behavior of an alpha + beta titanium alloy Ti-3Al-4V has been investigated at 910 deg. C. by using the method of cross head speed cycling. On the basis of flow stress, strain rate and strain rate sensitivity data, the alloy was found to exhibit strain hardening at this temperature which resulted in degradation in superplastic properties of the alloy. A high beta-phase volume fraction and grain-growth in both alpha and beta phases were considered responsible for the observed hardening effect. (author)

International Nuclear Information System (INIS)

Total dose irradiation effects on a VDMOS developed at Institute of Microelectronics, CAS were investigated, particularly the electric parameter changes under different bias conditions. It was found that the breakdown voltage degradation by the irradiation depended mainly on the drain bias, whereas the threshold voltage degradation depended mainly on the gate bias. Thus, an innovative and effective method to domestic VDMOS total dose ionization characterization is that threshold voltage radiation hardening characterization should be tested on gate bias condition, and the breakdown voltage radiation hardening characterization, be tested on the drain bias. (authors)

International Nuclear Information System (INIS)

... University, Fracture and Reliability Research Institute, Sendai, Miyagi (Japan)

Energy Technology Data Exchange (ETDEWEB)

Formulas were developed based on an aqueous solution of hydrolyzed polyacrylonitrile widely used in the oil industry. The additive used consisted of products of industrial production: synthetic resin TEG-1 with hardening agent PEPA (polyehtylene polyamine) and technical formalin. The mixtures containing about 80-85% by volume 5% hydrolyzed polyacrylonitrile, 10-15% by volume of resin TEG-1 with hardening agent PEPA and 3-5% by volume formalin satisfy the requirements made for the plugging materials. The initial mixtures are distinguished by technological efficiency of preparation and have controllable hardening periods. Physical-chemical properties are given for the gel polymers. In the set of properties, the mixtures based on hydrolyzed polyacrylonitrile, resin TEG-1 with hardening agent PEPA and formalin can be recommended as plugging materials of temporary action with complex treatment of the ...

International Nuclear Information System (INIS)

The #beta#-CEZ alloy : Ti-5%Al-2%Sn-4%Zr-4%Mo-2%Cr-1%Fe is a near #beta# titanium alloy. Since its processing routes include heat treatment (consisting of solution treatment and ageing), it has been decided to study the influence of the #beta# phase stability on #alpha# phase precipitation and hardening kinetics. Small sized specimens, coming from industrial heats, have been heat treated above and below the #beta# transus, and then water quenched. Therefore, several degree of #beta# stability are obtained. When it is increased (i.e. the solution treatment temperature is lowered), #alpha# or #omega# phases precipitations are delayed, as well as the hardening phenomena. Moreover, the #omega# stability domain is reduced. The mechanisms of #alpha# or #omega# precipitation are discussed, and related to the hardening kinetics. (orig.).

Energy Technology Data Exchange (ETDEWEB)

We report the direct molecular dynamics simulations for molecular ball bearings composed of fullerene molecules (C{sub 60} and C{sub 20}) and multi-walled carbon nanotubes. The comparison of friction levels indicates that fullerene ball bearings have extremely low friction (with minimal frictional forces of 5.283 x 10{sup -7} and 6.768 x 10{sup -7} nN/atom for C{sub 60} and C{sub 20} bearings) and energy dissipation (lowest dissipation per cycle of 0.013 and 0.016 meV/atom for C{sub 60} and C{sub 20} bearings). A single fullerene inside the ball bearings exhibits various motion statuses of mixed translation and rotation. The influences of the shaft's distortion on the long-ranged potential energy and normal force are discussed. The phonic dissipation mechanism leads to a non-monotonic function between the friction and the load rate for the molecular bearings.

Energy Technology Data Exchange (ETDEWEB)

IMO Momentenlager GmbH of Gremsdorf near Nuremberg produces large rotary bearings for ENERCON wind power systems, preferably for the E-70 and E-82 generators. (orig.)

UK PubMed Central (United Kingdom)

BackgroundLignocellulosic biomass such as wood is an attractive material for fuel ethanol production. Pretreatment technologies that increase the digestibility of cellulose and hemicellulose...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Using the [sup 57]Fe Moessbauer spectroscopy, the microscopic behavior of Fe powders has been investigated during and after the mechanical alloying (MA) process for Al-Fe and Ag-Fe systems. A repeated rolling method as well as a conventional ball-milling method are employed in order to understand the microscopic process of the kneading of Al and Fe powders during their MA and the resultant powders show quite similar Moessbauer spectra suggesting that the kneading by an impact between colliding balls is the same process as that of the thickness reduction by cold rolling. Moessbauer spectra show clearly the occurrence of the mutual atomic dispersion for the thermodynamically immiscible Ag-Fe system. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Spherical {beta}-Ni(OH){sub 2} was modified by a low-cost method of normal ball milling (NBM), and the physical properties of both ball-milled and un-milled Ni(OH){sub 2} were characterized by transmission electron microscopy, specific surface area, particle size distribution and X-ray diffraction. It was found that NBM could obviously increase the surface area, decrease the particle and crystallite size, and reduce the crystallinity of {beta}-Ni(OH){sub 2}, which were advantageous to the improvement of the electrochemical activity of Ni(OH){sub 2}. NBM also lowered the packing density and flowability of Ni(OH){sub 2}, as revealed by the measurements of tapping density and angle of repose. Electrochemical performances of pasted nickel electrodes with an addition of ball-milled Ni(OH){sub 2} to spherical Ni(OH){sub 2} as the active material were investigated, and were compared with those of the pure spherical Ni(OH){sub 2} ...

Science.gov (United States)

A post-accident-heat-removal structural effects analysis for the steel liner in the FFTF concrete containment structure is presented. (JWR)

International Nuclear Information System (INIS)

A study is made of the mechanical properties of vanadium irradiated with fast neutrons up to dose 8.6.10"-"4 dpa, as a function of the temperature of post-radiation annealing. The radiation-annealing hardening (RAH) effect is observed at 300"oC, in agreement with previous studies. It is established for the first time that RAH is accompanied by fall in ductility. A phenomenological model is described which explains the dependence of RAH on radiation dose and temperature, as well as on the content of chemically active alloying impurities. (author).

International Nuclear Information System (INIS)

SGS-Thomson and CNES significantly hardened a power MOSFET transistor against heavy ions and cobalt 60 total dose. The influence of the major technological steps on the component radiation sensitivity has been analyzed. Then the optimization has been carried out, using booth computerized simulation and experimental data. (D.L.). 5 refs., 8 figs.

International Nuclear Information System (INIS)

Power devices such as MOSFETSs and IGBTs, include parasitic structures that can give rise to destructive failures such as breakdown and latch-up. To determine a suitable strategy for device radiation hardening, simulation software like MEDICI-2D can be used to model the effects of technological modifications and device parameters that are difficult to measure experimentally. (authors).

Energy Technology Data Exchange (ETDEWEB)

The quantitative measurement of carbon concentration-distance curves serves as fundamental prerequisite for the evaluation of rim zone properties connected with decarburisation processes in material science. This was shown in part 1 of the present work with two samples from through-hardenable rolling bearing steel 100Cr6 (SAE 52100) austenitised in different oxidising atmospheres by position dependent determination of hardness, residual stresses, and X-ray line broadening ({l_brace}211{r_brace} {alpha}'-Fe diffraction line). In practice, it is important to predict carbon concentration-distance curves under prevailing heat treatment conditions or to conclude conversely from profile measurements. Based on a refined kinetics model of a diffusion-controlled process, part 2 therefore presents a simulation tool developed by means of the finite element method (FEM). Apart from the concentration dependence of the diffusion coefficient, it also ...

Energy Technology Data Exchange (ETDEWEB)

Fatigue tests were accomplished with a series of specimens doped with trace elements of a hardened Fe-Ni-Cr alloy, cast and hardened with intermetallic phases for determining the influence of these elements on the high temperature strength properties. The results of extensive fatigue tests show that even small contents of Te, Bi, Se, Pb, Tl and Zn considerably influence the life and creep processes especially after longer running periods, when added individually or combinedly. In contrast to this, the fatigue ductility is reduced by trace element additions even with short running periods. The order in which the metallic trace elements influence the fatigue properties nearly correlates with earlier work concerning Ni- and Co-superalloys. (orig.)

International Nuclear Information System (INIS)

Defect cluster formation in 14-MeV neutron irradiated polycrystalline copper has been observed by transmission electron microscopy (TEM) and correlated with the increase in yield stress. The measurements indicate that the radiation hardening component of the yield strength in polycrystals is not directly additive to the unirradiated yield strength. A transitional behavior was observed for radiation hardening at low fluences, which produces an anomalous variation of the defect cluster barrier strength with fluence. The behavior is attributed to the effect of grain boundaries on slip band transmission. An upper limit for the room temperature barrier strength of defect clusters in neutron-irradiated copper was determined to be #alpha#=0.23. (orig.).

International Nuclear Information System (INIS)

Nano indentation analysis and transmission electron microscopy observation were performed to investigate a microstructural evolution and its influence on the hardening behavior in Fe-Cr alloys after an irradiation with 8 MeV Fe4+ ions at room temperature. Nano indentation analysis shows that an irradiation induced hardening is generated more considerably in the Fe-15Cr alloy than in the Fe-5Cr alloy by the ion irradiation. TEM observation reveals a significant population of the a0 dislocation loops in the Fe-15Cr alloy and an agglomeration of the 1/2a0 dislocation loops in the Fe-5Cr alloy. The results indicate that the a0 dislocation loops will act as stronger obstacles to a dislocation motion than 1/2a0 dislocation loops.

International Nuclear Information System (INIS)

Precipitation-hardened single crystals of a beta (bcc) Ti--40 at. percent V--1.0 at. percent Si alloy were deformed in compression at 77 and 298"0K. The dependence of the yield stress upon aging time at 843"0K for solution-treated crystals shows two maxima which are caused by silicide precipitates. The orientation dependence of the yield stress and of the active macroscopic slip plane were determined as a function of aging time. The solution-treated as well as aged crystals exhibit an asymmetry of both the yield stress and the plane of slip, the degree of asymmetry being larger at 77 than at 298"0K. The asymmetry of slip and yielding is not affected by the presence of precipitation hardening. Results indicate that the effect of the dislocation core structure on dislocation motion is independent of the presence of precipitates. (auth).

Energy Technology Data Exchange (ETDEWEB)

A parametric experimental investigation of an 85 millimeter bore angular contact ball bearing running in RP-1 fuel was performed at speeds of 10,000 to 24,000 rpm. Thrust loads were varied from 4450 to 17,800 Newtons (1000 to 4000 lbs.). Radial loads were varied from 1335 to 13,350 Newtons (300 to 3000 lbs.). RP-1 lubrication for the bearing was provided through a stationary jet ring located adjacent to the test bearing outer ring. Increases in both the thrust and radial loads resulted in increased bearing temperature, while increases in shaft speed resulted in much more dramatic increases in bearing temperature. These trends are typical for ball bearings operating under these types of conditions. Results are given for outer ring temperatures of the test bearing at the various test conditions employed. In addition, the heat energy removed from the bearing by the RP-1 was determined by measuring the increase in temperature as the RP-1 passed ...

Energy Technology Data Exchange (ETDEWEB)

LiFePO{sub 4} cathode materials with distinct particle sizes were prepared by a planetary ball-milling method. The effects of particle size on the morphology, thermal stability and electrochemical performance of LiFePO{sub 4} cathode materials were investigated. The ball-milling method decreased particle size, thereby reducing the length of diffusion and improving the reversibility of the lithium ion intercalation/deintercalation. It is worth noting that the small particle sample prepared using malonic acid as a carbon source achieved a high capacity of 161 mAh g{sup -1} at a 0.1 C rate and had a very flat capacity curve during the early 50 cycles. However, the big particle samples ({proportional_to}400 nm) decayed more dramatically in capacity than the small particle size samples ({proportional_to}200 nm) at high current densities. The improvement in electrode performance was mainly due to the fine particles, the small size distribution, and ...

International Nuclear Information System (INIS)

The influence of chemical composition and heat treatment on a low-carbon steel, chromium steel and high speed steel has been examined by polarisation curves and electrochemical parameters deduced from the Tafel plots. The electrochemical corrosion resistance, which is small between the as-received steels become greater after heat treatment, following the order: carbon steel < chromium steel #approx# high speed steel. To explain these differences, the nano- and microstructure of the steels has been characterized by the ex situ techniques of atomic force microscopy and optical microscopy, before and after surface etching with Nital (a solution of 5% HNO_3 in ethanol). This causes preferential attack of the ferrite phases showing the carbide phases more clearly. From these nanostructural studies it was possible to better ...

British Library Electronic Table of Contents (United Kingdom)

Drosophila melanogaster is a model organism rich in genetic tools to manipulate and identify neural circuits involved in specific behaviors. Here we present a technique for two-photon calcium imaging in the central brain of head-fixed Drosophila walking on an air-supported ball. The ball's motion is tracked at high resolution and can be treated as a proxy for the fly's own movements. We used the genetically encoded calcium sensor, GCaMP3.0, to record from important elements of the motion-processing pathway, the horizontal-system lobula plate tangential cells (LPTCs) in the fly optic lobe. We presented motion stimuli to the tethered fly and found that calcium transients in horizontal-system neurons correlated with robust optomotor behavior during walking. Our technique allows both behavior ...

International Nuclear Information System (INIS)

A steadily increasing part of comminution is nowadays carried out by tube ball mills. Our investigations are a first step to a possible tuning of material distribution with mechanical stress characteristic of the grinding media charge, that is essential for a high efficiency of grinding. A BOND mill filled with porcelain balls as grinding media and labelled corundum (Au-198) as grinding material was used to measure the distribution of material over the cross-section. The evaluation was made by linear interpolation between all combinations of adjacent measuring points to calculate all coordinates with equal intensity for each selected level of activity. Two plottings showing the dependence of material distribution on the rotating speed are presented. (author).

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Ultrafine particles of Co-P were synthesized by direct ball milling of Co and P powders and also investigated as a reversible hydrogen storage electrode material. The electrochemical results demonstrated that the reversible charge-discharge capacity of the Co-P electrode can reach more than 300mAh/g. In addition, the cycling ability and high rate capability of the Co-P electrode are excellent with only 5% capacity decay after 100 cycles at a high rate of 300mA/g. The temperature-programmed desorption measurements (TPD) of the Co-P electrode revealed that the charge and discharge reactions of the Co-P electrode proceeds predominantly through electrochemical hydrogen storage mechanism and the electrooxidation of cobalt contributes only a negligible part to the reversible electrochemical capacity. (author)

International Nuclear Information System (INIS)

A variety of advanced controlled rolling techniques have been developed to improve toughness, strength and weldability of niobium-steels. To achieve optimum properties, control of prior stage rolling conditions and accelerated cooling are needed. In low carbon steel, the addition of niobium results in a greater increase in tensile strength than that of vanadium without a loss of toughness. At the same strength level, niobium-steel has less susceptibility to weld cracking and good toughness in the HAZ of its weldments than similar vanadium steels. Separation and formability of niobium steels are also discussed.

International Nuclear Information System (INIS)

The methods of surface modification of Ti-Zr alloy by laser treatment are considered. Characteristics of laser modification without- and with surface melting and with melting in different gaseous environments and with nickel microalloying are presented. Maximum depth, hardness and corrosion resistance are observed under nickel laser alloying.

Energy Technology Data Exchange (ETDEWEB)

Microalloyed or high strength low alloy (HSLA) steels are carbon-manganese steels containing small amounts of Nb, V or Ti. The excellent mechanical properties of these alloys, particularly high yield strength, usually obviate the need for expensive quench and tempering operations. Furthermore, the presence of a significant amount of nitride-forming elements in some microalloyed steels has generated interest in the applicability of these alloys as a new generation of nitriding steels. In this paper, a study of the plasma nitriding behaviour of a commercially available microalloyed steel MAXIMA{sup TM} is reported. A comparison is made with a traditional quenched and tempered nitriding steel (En19), plasma nitrided under similar conditions. Optical and scanning electron microscopy in conjunction with microhardness measurements and X-ray diffraction were utilized ...

Science.gov (United States)

... Accession Number : ADD130998. Title : Development of Grade API X80 Pipeline Steel Plates Produced by Controlled Rolling,. Corporate Author : ...

International Science & Technology Center (ISTC)

Corrosion- and Wear Resistant Silicon Containing Chromium-Manganese and Nickel-Chromium-Manganese Nonmagnetic Steels with Increased Strength and Toughness for Reliable Work at Normal and Cryogenic Temperatures

International Nuclear Information System (INIS)

Effect of strain and temperature on high temperature deformation properties of an alpha + beta titanium alloy Ti-6Al-4V has been investigated in the temperature range 800 to 910 deg. C by using the method of cross head speed cycling. On the basis of flow stress strain rate-strain rate sensitivity data and microstructural studies of the undeformed and deformed regions of tensile test pieces, both strain introduced hardening and softening effects were observed during the course of deformation which could be associated with grain coarsening and refining respectively. (author)

International Nuclear Information System (INIS)

The Joint Work Session of the ITER CDA (Conceptual Design Activities) by four parties, (eg. Japan, USA, USSR and EC), which has continued during 3 years from May 1988 to December 1990 was completed successfully. During the CDA, overall diagnostic systems for the next generation machine was performed for the first time and the principal tasks of Diagnostic research and development (R and D) are identified. In this paper, radiation hardening problems, which should be solved for the period 1991 through 1996 of the ITER EDA (Engineering Design Activities), are described. (author).

International Nuclear Information System (INIS)

Some results on mechanical property study of copper and titanium subjected to impact load and next to neutron irradiation are presented. It was shown that shock wave influence involves a substantial shape change of the stress-strain diagram and of respective mechanical characteristics. Yield- and ultimate strength were substantially increased, as well as hardness with a considerable drop of plasticity. Also a heat stability of copper and titanium specimens was studied after being treated with shock-waves and neutron radiation. Results are given of electron microscope study of titanium structure sfter explosion hardening, which caused decomposition of hydride segregations in titanium and increased dislocation density.

International Nuclear Information System (INIS)

The procedure of charge-coupled devices (CCD) are investigated by using MOS capacitors for enhancing their ionizing radiation tolerance. Authors have found that the gate oxidation temperature, thickness of SiO_2 gate insulator and high temperature processes after gate oxidation are crucial for determining the radiation tolerance of the devices, and proposed to decrease the thickness of gate insulator, perform gate oxidation at 1000 deg C by means of dry oxidation and minimize the number of high temperature procedure steps after gate oxidation. All stated above is a necessary preparation for priducing radiation hardened charge-coupled devices.

Energy Technology Data Exchange (ETDEWEB)

The rate of corrosion of hardened cement paste in solutions of nitric, hydrochloric, sulfuric, acetic and formic acids was compared. Corrosion in solutions of acetic and nitric acids with different concentrations was studied in more detail. The results made it possible to obtain the relationships expressing the influence of concentration and the time of action of acid solutions on the depth of corrosion. The rates of corrosion in nitric acid solutions during the first 3 years were about 2 to 4 times that in acetic acid solutions, depending on the concentration.

Energy Technology Data Exchange (ETDEWEB)

Biomass and nutrient dynamics of black spruce seedlings during the hardening phase of the greenhouse rotation were examined after four pre-hardening fertilization regimes - conventional, constant-rate loading, exponential loading, and high exponential loading (delivering respectively 15, 40, 40 and 60 mg N seedling{sup -1}) - in order to assess nutrient dilution and steady-state nutrition. Although height growth of seedlings had virtually ceased during hardening, shoot biomass increased 99-142% and root biomass increased five- to tenfold depending on treatment. The biomass increase compromised steady-state nutrient status by diluting internal nutrient pools as nutrient supply was unable to keep up with growth. Soil nutrient levels were rapidly depleted during this period because of plant uptake and lack of fertilizer supplementation. Pre-hardening nutrient loading partly countered and delayed dilution ...

Wastenet

... One 20 litre and one 15 litre removable bins Quick and easy installation Slides in and out on ball bearing track W248 x D455 x H485mm In Stock Email a Friend Quantity : 㿝.95 inc VAT Segregated Bins Stacked Bins Built-In Bins Office Bins Can Crushers Bags and Liners Accessories ...

British Library Electronic Table of Contents (United Kingdom)

We prove that Formula Not Shown surface diffeomorphisms have symbolic extensions, i.e. topological extensions which are subshifts over a finite alphabet. Following the strategy of Downarowicz and Maass (Invent. Math. 176:617?636, 2009) we bound the local entropy of ergodic measures in terms of Lyapunov exponents. This is done by reparametrizing Bowen balls by contracting maps in a approach combining hyperbolic theory and Yomdin?s theory.

Science.gov (United States)

... Title : THE INFLUENCE OF GRAIN BOUNDARY CARBIDE DENSITY ON THE BRITTLE FRACTURE OF FERRITE PEARLITE STEELS. ...

British Library Electronic Table of Contents (United Kingdom)

Ultrafine grained steels with different carbon contents were produced through warm caliber rolling and evaluated for their stress-strain behavior along with the reduction in area. It was found that the reduction in area-tensile strength balance is far better than the conventional ferrite+pearlite steels and even superior to bainitic steels for all materials tested in the present study.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

... Engineering, Kitakyushu, Fukuoka (Japan) Hattanda, Takumi NTT Advanced

International Nuclear Information System (INIS)

Both the price of nickel and the allergic reaction that it can cause to human beings make it desirable to develop and use nickel-free austenitic stainless steels. The steels should be austenitic so as to avoid ferro-magnetism, a condition which has to be fulfilled for a number of requirements, including its use as implants in the human body, for wrist watch cases and many others. The paper presents the development of a nickel-free steel containing 11 percent manganese, 17 percent chromium, 4 percent molybdenum, and 0.9 percent nitrogen. This austenitic stainless steel has exceptional strength and corrosion resistance. These properties could result in numerous applications of the steel. A limitation, however, is that the steel is not weldable.

Energy Technology Data Exchange (ETDEWEB)

In this book over 250 alloys are organized by AISI number into 10 major sections: Irons, Carbon Steels, Alloy Steels, Low Alloy Constructional Steels, Ultra High Strength Steels, Tool Steels, Maraging Steels, Wrought Stainless Steels, Heat Resistnat Casting Alloys, and Iron Based Rought Superalloys. Each alloy record lists the designation, specifications, UNS number, composition, product forms and a comment on the high-temperature properties and applications. Referenced data is then given for physical properties such as density, specific heat, thermal conductivity, thermal expansion, electrical conductivity, Poisson's ratio, moduli of elasticity and rigidity, etc. Mechanical properties follow, and include tensile properties, shearing and bearing properties, impact properties, creep, stress rupture and stress relaxation and fatigue ...

Energy Technology Data Exchange (ETDEWEB)

We consider the case of a test sphere (ball) of radius a{sub 1} rotating at constant angular velocity {omega} in an otherwise quiescent unbounded suspension of uniformly sized spheres of radii a{sub 2} dispersed in a Newtonian fluid of viscosity {mu}. To the first order in the volume fraction c of suspended spheres it is shown that when the ball is small compared with the suspended spheres the suspension does not behave as regards the hydrodynamic torque L exerted on the ball like a homogeneous Newtonian fluid characterized by the usual Einstein viscosity coefficient {mu}{sub s}={mu}(1+5/2c). Explicitly, the torque on the rotating sphere does not obey Kirchoff{close_quote}s law, L=8{pi}{mu}{sub s}a{sub 1}{sup 3}{omega} for no slip. Rather, a modified form of Kirchoff{close_quote}s law is obtained in which the Einstein coefficient of 5/2 is multiplied by a coefficient which is less than unity in magnitude and is functionally ...

International Nuclear Information System (INIS)

Growing competitiveness of alternative manufacturing routes requires cost minimization in the production of drop forged components. The authors analyse the potential of medium carbon, vanadium microalloyed steels for drop forging. Laboratory and industrial experiments have been carried out emphasizing deformation and temperature cycles, strain rates and dwell times showing a typical processing path, associated mechanical properties and corresponding microstructures. The steels the required levels of mechanical properties on cooling after forging, eliminating subsequent heat treatment. The machinability of V-microalloyed steels is also improved when compared with plain medium carbon steels. (author)

International Nuclear Information System (INIS)

The effect of the rare earth element, yttrium, on the mechanical properties of 9Cr-2WVTa low active martensite steel for fusion reactor was studied and the metallurgical behavior of yttrium in the steel was primarily analyzed. The results show that it is easy for yttrium to aggregate and form the blocky yttrium rich inclusions in the steel, which can dissever the continuity of the matrix and produce micro-cracks for fracture. The yttrium rich inclusions were distributed along the rolling direction, which made the fracture surface delaminated in the tensile and impact samples, and reduced the mechanical properties of the steel. (authors)

International Nuclear Information System (INIS)

The creep crack growth properties of two versions of Alloy 800 have been compared at 500 and 600"0C in the Grade II condition in tests up to 10"4 hours duration. The two alloys were a low carbon alloy containing (wt.%) 0.024 C, 0.5 Ti, 0.3 Al (Alloy B) and a higher carbon alloy containing (wt.%) 0.038 C, 0.2-0.3 Ti, 0.2-3.0 Al (Alloy J). At 600"0C, Alloy B attained maximum age hardening in 10"2 hours, whereas J did not harden significantly in time up to 10"4 hours. Both alloys age hardened at 550"0C with Alloy J hardening more rapidly than B. The creep displacements and displacement rates in small compact tension specimens at 600"0C were smaller than Alloy B than in Alloy J. However, failure times were shorter in Alloy B because of lower displacements for crack initiation and propagation and higher crack growth rates. At 550"0C the displacements for initiation and propagation in Alloy J were smaller ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the test results on high-temperature strength properties of fire resistant steel(FR steel) for building, the formulation, and the examples of application to member tests and actual buildings. Because of its components and manufacturing method, FR steel excels in strength at elevated temperature due to precipitation and dispersion strengthening. Tests on high temperature properties of FR steel showed that every property such as strength, stress-strain curve, elastic modulus, and creep performance at high temperature was superior to those of conventional steels. Then, it was confirmed in the tensile tests at room temperature and high temperature after heat history that FR steel could be reused after fire. It was also found in the member tests that columns and beams of FR steel could support loadings equivalent to long-term ...

International Nuclear Information System (INIS)

68 replaced carbon steel piping in secondary system of pressurized water reactor (PWR) has been investigated by visual examination for checking thinning conditions. It is well known that the flow-accelerated corrosion (FAC) was inhibited by traces of Cr in steel. Therefore, the chemical compositions of those steels have been measured. In addition, the micro structure and hardness of those steels have been investigated. And the relationship between those material variables and FAC rate was considered. As the results, (1) The Cr contents in those steels were below 0.1 wt% except one sample. Minute quantities of chromium increase the resistance against FAC. But the water velocity was thought to be the dominant factor rather than chemical composition in steel, at least such as below 0.1%Cr. (2) Hardness of all piping has been satisfied the specifications of each ...

International Nuclear Information System (INIS)

Ten different alloys of zirconium have been tested with regard to the effect of irradiation on their mechanical properties and their sensitivity to environmentally induced failure. Two different environments were used: iodine vapour and liquid cesium with an addition of 2% cadmium. The neutron dose was 10"2"1n/cm"2 (E>1MeV) and the irradiation temperature was about 300 degrees C. All alloy additions increased the irradiation hardening. Especially notable was the large effect of titanium and tin on irradiation hardening. A limited amount of transmission electron microscopy was carried out in order to find an explanation to the effects. The testing in different environments showed that there is no clear correlation between environmental sensitivity and yield stress. For materials of similar yield stress an alloyed material tends to be more sensitive to environmental cracking than a material which only contains oxygen as an impurity. There also ...

CERN Document Server

Volume sources is used for standard sources by radioactive measurement using Ge semiconductor detector of environmental sample, e.g. water, soil and etc. that require large volume. The commercial volume source used in measurement of the water sample is made of agar-agar, and that used in measurement of the soil sample is made of alumina powder. When the plastic receptacles of this two kinds of volume sources were damaged, the leakage contents cause contamination. Moreover, if hermetically sealing performance of volume source made of agar-agar fell, volume decrease due to an evaporation off moisture gives an error to radioactive measurement. Therefore, we developed the two type methods using unsaturated polyester resin, vinilester resin, their hardening agent and acrylicresin. The first type is due to dispersing the hydrochloric acid solution included the radioisotopes uniformly in each resin and hardening the resin. The second is due to ...

CERN Document Server

The massive stars in the Galactic center inner arcsecond share analogous properties with the so-called Hot Jupiters. Most of these young stars have highly eccentric orbits, and were probably not formed in-situ. It has been proposed that these stars acquired their current orbits from the tidal disruption of compact massive binaries scattered toward the proximity of the central supermassive black hole. Assuming a binary star formed in a thin gaseous disk beyond 0.1 pc from the central object, we investigate the relevance of disk-satellite interactions to harden the binding energy of the binary, and to drive its inward migration. A massive, equal-mass binary star is found to become more tightly wound as it migrates inwards toward the central black hole. The migration timescale is very similar to that of a single-star satellite of the same mass. The binary's hardening is caused by the formation of spiral tails lagging the stars inside the binary's ...

Energy Technology Data Exchange (ETDEWEB)

With the aim of optimizing the nitriding process, experimental studies of the plasma nitriding of four selected steels were carried out, using a d.c. glow discharge. The process parameters were varied systematically. By means of transmission and scanning electron microscopy and X-ray diffraction, the microstructures, including the thicknesses of the compound zones and the diffusion zones of the nitrided steels, were obtained. Using cross-sectional samples and a micro-Vickers indenter, hardness depth profiles were also obtained. From the time and temperature dependences of the hardness profiles, effective diffusion constants and corresponding activation enthalpies were obtained. Furthermore, in an attempt to shed some light on the atomistic nitriding mechanisms, the glow discharges were studied by measuring energy spectra of the energetic ions hitting the cathode (the steel test specimens). It was shown that an increase of ...

International Nuclear Information System (INIS)

In this study, effects of alloying elements such as Mo, Cr and Ni on intergranular corrosion (IGC) resistance of Mo contained austenitic stainless steels in boiling 65% nitric acid solution (Huey Test) were studied. Obtained results are as follows; (1) Mo deteriorates IGC resistance of austenitic stainless steel in Huey test due to enhance precipitation of Laves ((Fe, Cr)_2Mo) phase at grain boundary. (2) Cr improves IGC resistance of Mo contained austenitic stainless steel in Huey test, which is considered to reduce dissolution rate of Laves phase into nitric acid solution by increasing Cr content in Laves phase as increasing Cr content of stainless steel. (3) Ni suppresses occurrence of IGC of Mo contained austenitic stainless steel in Huey test. (author).

International Nuclear Information System (INIS)

Tungsten (W) coating on fusion candidate V-4Cr-4Ti (NIFS-HEAT-2) substrate was demonstrated with plasma spray process for the purpose of applying to protection of the plasma facing surface of a fusion blanket. Increase in plasma input power and temperature of the substrate was effective to reduce porosity of the coating, but resulted in hardening of the substrate and degradation of impact property at 77 K. The hardening seemed to be due to contamination with gaseous impurities and deformation by thermal stress during the coating process. Since all the samples showed good ductility at room temperature, further heating seems to be acceptable for the vanadium substrate. The fracture stress of the W coating was estimated from bending tests as at least 313 MPa, which well exceeds the design stress for the vanadium structure in fusion blanket. (author)

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

International Nuclear Information System (INIS)

Microprocessor based ''smart'' pressure, level, and flow transmitters were tested to determine the radiation hardness of this class of electronic instrumentation for use in reactor building applications. Commercial grade Complementary Metal Oxide Semiconductor (CMOS) integrated circuits used in these transmitters were found to fail at total gamma dose levels between 2500 and 10,000 rad. This results in an unacceptably short lifetime in many reactor building radiation environments. Radiation hardened integrated circuits can, in general, provide satisfactory service life for normal reactor operations when not restricted to the extremely low power budget imposed by standard 4--20 mA two-wire instrument loops. The design of these circuits will require attention to vendor radiation hardness specifications, dose rates, process control with respect to radiation hardness factors, and non-volatile programmable memory technology. 3 refs., 2 figs.

British Library Electronic Table of Contents (United Kingdom)

The RD50 collaboration has been exploring the development of radiation hard semiconductor devices for very high-luminosity colliders since 2002. The target fluence to qualify detectors set by the anticipated dose for the innermost tracking layers of the future upgrade of the CERN large hadron collider (LHC) is 1016 1MeV neutron equivalent (neq) cm-2. This is about an order of magnitude higher than the maximum dose for the most exposed silicon detectors in the current machine. RD50 investigates the radiation hardening of silicon sensors from many angles: improvement of the intrinsic tolerance of the substrate material, optimisation of the readout geometry and study of novel design of detectors. A review of some of the recent activities within RD50 is here presented.

British Library Electronic Table of Contents (United Kingdom)

Modifications of the structure and mechanical properties in LiF crystals irradiated with MeV-energy Au ions have been studied using nanoindentation, atomic force microscopy and optical spectroscopy. The nanostructuring of crystals under a high-fluence irradiation (above 1013 ions/cm2)?was?observed. Nanoindentation tests show a strong ion-induced increase of hardness (up?to 150?200%), which is related to the high volume concentration of complex color centers, defect aggregates, dislocation loops and grain boundaries acting as strong barriers for dislocations. From the?depth profiling of the hardness and energy loss it follows that both nuclear and electronic stopping mechanisms of MeV Au ions contribute to the creation of damage and hardening. Whereas the electronic stopping is dominating i...

International Nuclear Information System (INIS)

The introduction of tolerance to radiation (''radiation-hardness'') into large electronic systems is one of the major tasks to which this Handbook will be put. The practices recommended here for inculcating radiation-tolerance in equipment require advanced physical modeling techniques, precise engineering procedures, and firm assurance procedures. The degree to which these procedures should be used in an equipment project can be measured by the severity of the raw radiation environment, the desired reliability of the system, and the requirement of that project for radiation-sensitive technologies. The balance of device/circuit design versus shielding will depend on whether the radiation is highly penetrating -- as in isotope handling or military environments -- or readily attenuated, as in space. In this chapter the authors have attempted to summarize the essential features of the radiation hardening of large assemblies of equipment and how effective control of ...

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline cemented tungsten carbide has attracted considerable interests for use in cutting tool because of its superior mechanical properties. In this study, nano-sized powders of mixed WC and Co were prepared from attrition-milled oxides by a gas reduction-carburization process. The effects of compacting pressure, heating schedule, additional ball-milling, and the presence of a grain growth inhibitor on the sintering properties of the nano-sized WC-Co powders were examined. The grain size and phases in WC-Co alloy were clearly affected by compacting pressure. Because of the trapped gases and the lower melting point of the cobalt binder, when a compact of nano-sized WC-Co powder was sintered through a heating schedule with holding steps, the sintered alloy maintained the small size of WC grains without any {eta} phase. In addition, the additional ball-milling improved the microstructure and mechanical properties of the nano-sized WC-Co ...

Energy Technology Data Exchange (ETDEWEB)

The durability of ball bearings, 32-mm- and 45-mm-bore, with a retainer or glass cloth-polytetrafluoroethylene (PTFE) laminate was tested under a high radial load at a speed of 20,000 rpm in LOX or LN2. The retainers were characterized as good self-lubricators because the abrasive glass-cloth fiber tips exposed on the retainer were chemicaly etched away with hydrofluoric acid (HF). During testing, the bearing-cartridge-acceleration was monitored to detect bearing damage. Testing in LOX for about 2.2 hr showed that excellent lubricating conditions were obtained for all bearings. Testing in LN2 for about 5.1 hr detected that the fatigue life of the bearing was about the same as the calculated B10 fatigue life. The HF chemical treatment resulted in a reacted fluoride-oxide material which remained in the etched part of the glass fiber. Several chemical products, particularly MgO, CaO, and CaCO3, enhanced adhesion of PTFE transfer film to the counterface, resulting in ...

Energy Technology Data Exchange (ETDEWEB)

Under severe operating conditions, such as starved lubrication, performance, service life, and reliability of rolling element bearings depend on the chemical and physical interactions between the contacting surfaces, the lubricant components, and the atmosphere. The IMKT{sup 1}, PI{sup 2}, and the imt{sup 3} have been cooperating on systematic investigations of interfacial interactions in high speed grease lubricated ball bearings. These include long time tests with complete bearings lubricated with greases of different composition under defined operating conditions, conducted at the IMKT, and chemical and physical characterizations of the running surfaces at the PI and imt. At the PI, in particular the chemical nature of the boundary layers has been investigated with time of flight secondary ion mass spectrometry (TOF-SIMS). The imt has been involved in the investigations by measuring the physical/mechanical properties of interacting surfaces at the ...

Energy Technology Data Exchange (ETDEWEB)

A series of ball-on-disc wear and friction measurements were made for surfaces which have a chemical vapour deposition carbon silicon alloy layer on a carbon substrate (fine grain POCO graphite). Nitrogen ion irradiation was used to improve the wear resistance of the carbon alloy surface. For comparison, measurements were also taken for alumina against alumina. It was found that the lowest friction coefficient and lowest wear occurred for ion irradiated coated samples containing 4% Si in the alloy and that the performance was superior to that of alumina. ((orig.))

Energy Technology Data Exchange (ETDEWEB)

An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves in the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first. 14 figs.

Energy Technology Data Exchange (ETDEWEB)

The pipelines is provided for gases, particluarly helium, at temperature of about 1000/sup 0/C (pressure about 40 bar) and is used as the connection be tween a gas cooled high temperature reactor and a heat load. The pipe consists of a temperature-resistant inner tube, which is composed of several pipe sections, which are supported on ball bearings, and a gas tight pressurised outer tube. There are supports and insulation between the two tubes. The sub-claims concern fixing of and bearings for the pipe sections. The description is very detailed and supplemented by drawings.

Wastenet

...Oster | Best sexual wellness info Best sexual wellness info Home Posts Tagged Oster Oster Professional 103 Stim-U-Lax Massager Reviews Made of 100% ball bearing construction Traditional frame design with special frame contour to fit hand and reduce hand fatigue Chrome housing and rubber hand pad Heavy-duty, single speed UL approved 120v This lightweight therapeutic massager combines the advantages of hand and mechanical massage. Its special contoured design reduces hand fatigue and its universal ...

Energy Technology Data Exchange (ETDEWEB)

A study was made of the variation in strength characteristics of group IV transition metal carbon nitrides alloyed with carbides or group V metal nitrides. A complex solid solution of titanium-niobium carbonitride was preliminarily synthesized to a homogeneous equilibrium state and then crushed. The calculated quantity of binder metal was added as elemental powders, the mixture was vibration ball milled in ethanol and the plasticized charge was used to press experimental specimens for mechanical testing. The studies showed that the high-temperature strength properties of the new cermet are superior to standard type KNT. The material is thus promising for use in the manufacture of tools. 8 references, 3 figures.

Wastenet

...page 50 results per page [1] 2 3 Products: 27 Page 1 of 3 Name List price Handbook of Structural Steel Connection Design and Details, 2nd Edition AU$186.36 ex-GST Terms ...

Energy Technology Data Exchange (ETDEWEB)

The global production of steel is predicted to increase rapidly to meet future demands. In order to conserve the natural resources, certain measures must be taken. These include perfecting the recycling of steel, improving the performance to extend the life of the material, and reduce the need for massive production of steel by increasing the strength of the material. This paper presented a design concept for ultrafine complex microstructure steel. The National Research Institute for Metals in Japan has worked on a project which investigated 800 MPa ferrite steel for welded structures with a chemical composition similar to 400 MPa-class plain carbon steel. The doubled strength was attributed to grain refinement. Novel welding techniques were also used for joining the ultrafine microstructure. In this study, low carbon Si-Mn ferrite-pearlite ...

UK PubMed Central (United Kingdom)

OBJECTIVE: To study cause specific mortality and cancer morbidity in workers exposed to the dust of grinding materials, grinding agents, and stainless steel, especially with regard to a possibly increased...Full Text Available

International Nuclear Information System (INIS)

Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized under a high magnetic field of 10 T. The formation mechanism was investigated and discussed in detail. The synthesized samples were characterized by XRD, SEM, TEM, EMPA, and vector network analysis. By doping MnO2 with Fe, the relative complex permittivity of MnO2 and its corresponding loss tangent clearly decreases, but its relative complex permeability and its corresponding loss tangent markedly increases. Moreover, the theoretically calculated values of reflection loss show that with increasing the Fe content, the as-prepared Fe-doped MnO2 exhibits good microwave absorption capability. -- Graphical Abstract: Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized in a high magnetic field of 10 T via a simple chemical process. Display Omitted Highlights: ? Fe-doped MnO2 with a hollow sea urchin-like ball chain ...

International Nuclear Information System (INIS)

Composite particles represented as TiV_2_._1Ni_0_._3-Raney Ni(R) were prepared by ball-milling a TiV_2_._1Ni_0_._3 alloy with Raney Ni in the presence of 0.01 M sodium hypophosphite (NaH_2PO_2) aqueous solution as a reducing agent. The composite particles had different morphology from original TiV_2_._1Ni_0_._3 alloy particles and TiV_2_._1Ni_0_._3-Raney Ni composite particles prepared by the ball-milling in the absence of the NaH_2PO_2 aqueous solution. In charge-discharge cycle tests, the TiV_2_._1Ni_0_._3-Raney Ni(R) composite electrode showed the maximum discharge capacity of 620 mAh g"-"1, while its cycle durability was similar to the TiV_2_._1Ni_0_._3 alloy electrode, which was explained from depth profiles of constituent elements by Auger electron spectroscopy (AES). In thermogravimetry (TG) and differential thermal analysis (DTA), two steps of dehydriding for hydrided TiV_2_._1Ni_0_._3-Raney Ni(R) composite started from much lower ...

CERN Document Server

A total of 50 000 tonnes of low-carbon steel sheet has been ordered for the LHC main magnets. After three years of production, about 10 000 tonnes of steel sheet have been produced by Cockerill-Sambre Groupe Usinor. This paper gives a summary of the manufacturing process and improvements implemented as well as an overview of the difficulties encountered during this production. Preliminary statistics obtained for the mechanical and magnetic steel properties are presented. (6 refs).

Science.gov (United States)

PMID:17346598

Energy Technology Data Exchange (ETDEWEB)

In recent years, the phase stability of austenitic stainless steels, and its effect on the mechanical properties of stainless steels, have been the subject of much interest. With the availability of new experimental techniques, new theoretical methods, and new computational procedures, significant advances have been made in understanding, and being able to predict, phase stability and mechanical properties of stainless steel welds. This paper reviews some of these developments, with an emphasis on recent work that has been done at Oak Ridge National Laboratory.

International Nuclear Information System (INIS)

Mixed microstructures have been studied in low- carbon microalloyed steels suitable for automotive applications, after continuous cooling from the hot-rolled condition. Microstructural features such as polygonal ferrite, bainitic and acicular ferrite and microphase constituent are identified using transmission electron microscopy. The influence of these mixed structures on the tensile strength, impact toughness and fracture behaviour is examined. It is found that improvements in impact toughness as compared with microalloyed medium- carbon ferrite/pearlite steels can be achieved from these predominantly acicular structures developed by controlling alloy composition and continuous cooling of these lower carbon steels. (orig.).

International Nuclear Information System (INIS)

It has been found out that 30HGSNA steel undergo cracking under action of stresses in aqueous solutions containing oxygen, while it show high resistance in deoxidated solutions. The purpose of such phenomena is the existence of sulfur inclusions in steel which are a centers of denting corrosion. That points acting as a stresses concentrators where pH factor decreases including hydrogen formation and its absorption in the metal. That mechanism is the main purpose of brittle steel cracking observed in oxygen rich solutions. (author).

International Nuclear Information System (INIS)

The additional error in measurement of the thickness of Kh18N10T steel for possible changes in composition with an energy of the photons of ionizing radiation of 10-80 keV was evaluated. The desirability of use of a type REIS-I x-ray emitter in measurement of the thickness of steel up to 1 mm is shown. The instrument provides measurement of the thickness of steel in the 0.1-1.0 mm range with a reproducibility of the results with an error not exceeding 0.5-1.0%. The measurement error with corrugations characteristic of bellows does not exceed 5%.

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

... Industry, Material Science Research Laboratory, Yokosuka, Kanagawa (Japan)

International Nuclear Information System (INIS)

... Yoshiaki Toshiba Corp., Nuclear Power Division, Yokohama, Kanagawa (Japan)

Science.gov (United States)

No abstract available.

International Nuclear Information System (INIS)

Results of researches on nitriding process of EJ961 steel are presented in this work. This steel was subjected to nitriding both on the cathode and on the isolated from cathode and anode substrate, that is at so called potential of glow discharged plasma. Nitriding processes were performed using device for glow discharge treatments with cooled anode. (author)

Energy Technology Data Exchange (ETDEWEB)

Structure of ferrite in drawn pearlitic steel containing 0.9 mass% C was investigated with X-ray diffraction technique using synchrotron radiation. In the detailed analysis of diffraction peaks of ferrite during the drawing process, it was experimentally revealed that the transformation of ferrite from bcc to bct due to the supersaturation of carbon in ferrite of heavily drawn pearlitic steel.

Energy Technology Data Exchange (ETDEWEB)

High and ultra-high strength steels for pipelines are produced by properly handling the steel microstructure. The metallurgical principles involved in the microstructure control are presented, with emphasis on TMCP processing, that comprises conventional controlled rolling followed by accelerated cooling. (author)

International Nuclear Information System (INIS)

Azobenzene dyes are effective inhibitors for austenitic 304 L and 316 L stainless steel corrosion in high acidic medium up to 7N. A good efficiency is obtained from weight loss and electrochemical Rsub(p) measurements in hydrochloric acid, while no inhibition is observed in sulfuric solutions. Transformation from the primarily azobenzene to other compounds give rise to enhanced protection of steel samples, and probable structures of the inhibiting species are proposed in view of our results.

International Nuclear Information System (INIS)

The pitting corrosion resistance of three different types of stainless steel implanted with silicon is investigated using the potentiokinetic polarization technique. The specimens are tested in 3% NaCl and 0.1 N HCl solutions. Silicon ion implantation inhibits pitting corrosion of the steels in both aqueous media. The corrosion resistance depends on the silicon dose. Post implantation annealing only slightly alters the localized corrosion. (author).

International Nuclear Information System (INIS)

Mutual influence of phosphorus and carbon on the tendency to integranular corrosion (IGC) of tempered austenitic stainless steels in boiling solutions of 65% HNO_3 and 27% of HNO_3+40 g/l Cr"6"+ was investigated. It is ascertained that under the action of carbon additions susceptibility of phosphorus-containing steels to IGC increases considerably in pure nitric acid and decreases in nitric acid containing the oxidant. Possible reasons for the effects observed are discussed.

Energy Technology Data Exchange (ETDEWEB)

One of the effective methods of deep modification of the surface of steels and alloys is the combination of ion implantation and plasma nitriding. In this work, the long-range effect is demonstrated in the case of combination of the effect of high- and low-energy ions of nitrogen on a martensitic steel for each ion implantation is usually not effective, and a titanium alloy used widely in industry.

Energy Technology Data Exchange (ETDEWEB)

The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented.

Energy Technology Data Exchange (ETDEWEB)

A case study is presented about the failure of a stainless steel blade reinforcing band in a steam turbine. The inspection results and analysis of samples of material are discussed. Being pitting corrosion and cracks the main defects found, a study of chemical composition and heat treatment state of the steel is made and findings are related to type of failure. (orig.)

International Nuclear Information System (INIS)

Full text.S235JR carbon steel is one of the most popular steels used in Lebanon. It is imported by steel dealers and is widely used by all fabricators and manufacturers of steels for many structural purposes and applications. This kind of steel has good ductile properties as well as excellent weldability. It is still known by its previous designation St 37-2 or E 24-2. S235JR is produced in many shapes and thicknesses such as steel plates, sheets, angles and different other geometric shapes. Standard chemical and mechanical tests were conducted and reported on S235JR hot-rolled structural low-carbon mild steel specimens collected from Lebanese steel market. The main objective of this work is to assure the compliance of these properties with those set by the steel manufacturer. The above mentioned ...

Energy Technology Data Exchange (ETDEWEB)

The strain gradient crystal plasticity theory is applied to study the deformation of planar single crystal with a void under a nominally uniaxial tension. The crystal theory assumes elevated strain hardening due to slip gradients and has a constitutive length scale. The effects of the void size with respect to the constitutive length scale on the single crystal deformation are investigated.