Infrared astronomical instruments require absorptive coatings on internal surfaces to trap scattered and stray photons. This is typically accomplished with any one of a number of black paints. Although inexpensive and simple to apply, paint has several disadvantages. Painted surfaces can be fragile, prone to shedding particles, and difficult to clean. Most importantly, the vacuum performance is poor. Recently a plasma enhanced chemical vapor deposition (PECVD) process was developed to apply thick (30 {micro}m) diamond-like carbon (DLC) based protective coatings to the interior of oil pipelines. These DLC coatings show much promise as an infraredblack for an ultra high vacuum environment. The coatings are very robust with excellent cryogenic adhesion. Their total infrared reflectivity of < 10% at normal incidence approaches that of black paints. We ...
We have obtained for the first time $K$-band infrared spectra of the soft X-ray transient V616 Mon (=A0620--00). We determine the 2-sigma upper limit to the fraction of light arising from the accretion disc to be 27 percent. The effect this has on the binary inclination, determined from modelling the infrared ellipsoidal variations is to increase it by less than 7 degrees and decrease the mass of the black hole by less than 3.6 Msun.
We consider the evolution of binary systems formed by a Supermassive Black Hole (SMBH) residing in the center of a galaxy or a globular cluster and a star in its immediate vicinity. The star is assumed to fill its Roche lobe, and the SMBH accretes primarily the matter of this star. The evolution of such a system is mainly determined by the same processes as for an ordinary binary. The main differences are that the donor star is irradiated by hard radiation emitted during accretion onto the SMBH; in a detached system, nearly all the donor wind is captured by the black hole, which strongly affects the evolution of the semi-major axis; it is not possible for companions of the most massive SMBHs to fill their Roche lobes, since the corresponding orbital separations are smaller than the radius ...
In order to investigate the systematics of the loop expansion in high temperature gauge theories beyond the leading order hard thermal loop (HTL) approximation, we calculate the two-loop electron proper self-energy #SIGMA# in high temperature QED. The two-loop bubble diagram of #SIGMA# contains a linear infrared divergence. Even if regulated with a nonzero photon mass M of order of the Debye mass, this infrared sensitivity implies that the two-loop self-energy contributes terms to the fermion dispersion relation that are comparable to or even larger than the next-to-leading order (NLO) contributions of the one-loop #SIGMA#. Additional evidence for the necessity of a systematic restructuring of the loop expansion comes from the explicit gauge-parameter dependence of the fermion damping rate at both one and two loops. The leading terms in the high temperature expansion of the two-loop self-energy for all topologies arise from ...
We study the high-energy emission of the Galactic black hole candidate GX 339-4 using INTEGRAL/SPI and simultaneous RXTE/PCA data. By the end of January 2007, when it reached its peak luminosity in hard X-rays, the source was in a bright hard state. The SPI data from this period show a good signal to noise ratio, allowing a detailed study of the spectral energy distribution up to several hundred keV. As a main result, we report on the detection of a variable hard spectral feature (>150 keV) which represents a significant excess with respect to the cutoff power law shape of the spectrum. The SPI data suggest that the intensity of this feature is positively correlated with the 25 - 50 keV luminosity of the source and the associated variability time scale is shorter than 7 hours. The simultaneous PCA data, however, show no significant change in the spectral shape, indicating that the source is not ...
We examine the accretion properties in a sample of 42 hard (3-60keV) X-ray selected nearby broad-line AGNs. The energy range in the sample is harder than that usually used in the similar previous studies. These AGNs are mainly complied from the RXTE All Sky Survey (XSS), and complemented by the released INTEGRAL AGN catalog. The black hole masses, bolometric luminosities of AGN, and Eddington ratios are derived from their optical spectra in terms of the broad H$\\beta$ emission line. The tight correlation between the hard X-ray (3-20keV) and bolometric/line luminosity is well identified in our sample. Also identified is a strong inverse Baldwin relationship of the H$\\beta$ emission line. In addition, all these hard X-ray AGNs are biased toward luminous objects with high Eddington ratio (mostly between 0.01 to 0.1) and low column density ($<10^{22} \\mathrm{cm^{-2}}$), which is most likely due to the ...
Large optical surveys provide an unprecedented census of galaxies in the local Universe, forming an invaluable framework into which more detailed studies of objects can be placed. But how useful are optical surveys for understanding the co-evolution of black holes and galaxies, given their limited wavelength coverage, selection criteria, and depth? In this conference paper I present work-in-progress comparing optical and mid-IR diagnostics of three "unusual" low redshift populations (luminous Seyferts, dusty Balmer-strong AGN, ULIRGs) with a set of ordinary star-forming galaxies from the SDSS. I address the questions: How well do the mid-infrared and optical diagnostics of star formation and AGN strength agree? To what extent do optical surveys allow us to include extreme, dusty, morphologically disturbed galaxies in our "complete" census of black hole-galaxy co-evolution?
Diamond-like carbon thin films for tribological applications were deposited by d.c.-magnetron sputtering of a graphite target in a pure argon atmosphere or in a reactive hydrogen or methane atmosphere at pressures between 0.1 and 1 Pa in a graded constitution to improve adhesion and reduce residual stress. The temperature of the metallic, carbon- and ceramic-like substrates was below 100 C. The mechanical, thermal, electronic and optical properties of the carbon thin films show a significant dependence on the ion energy. Below 220 eV, strongly adherent black conductive films with hardness values up to 2000 HV0.05 were obtained. Hard and superhard diamond-like carbon thin films were deposited in an energy range between 220 and 370 eV with hardness values up to 4000 HV0.05. They are insulating, optically transparent and show a high degree of hardness combined with high compressive ...
We report on the results of a simultaneous monitoring campaign employing eight Chandra X-ray (0.5-10 keV) and six VLA/EVLA (8.4 GHz) radio observations of NGC 4051 over seven months. Evidence for compact jets is observed in the 8.4 GHz radio band; This builds on mounting evidence that jet production may be prevalent even in radio-quiet Seyferts. Assuming comparatively negligible local diffuse emission in the nucleus, the results also demonstrate an inverse correlation of L_radio proportional to L_X-ray ^(-0.72+/-0.04) . Current research linking the mass of supermassive black holes and stellar-mass black holes in the "low/hard" state to X-ray luminosities and radio luminosities suggest a "fundamental plane of accretion onto black holes" that has a positive correlation of L_radio proportional to L_X-ray^(0.67+/-0.12) . Our simultaneous results differ from this relation by more than 11 sigma, indicating ...
We consider isolated compact remnants (ICoRs), i.e. neutrons stars and black holes that do not reside in binary systems and therefore cannot be detected as X-ray binaries. ICoRs may represent $\\sim\\,5$ percent of the stellar mass budget of the Galaxy, but they are very hard to detect. Here we explore the possibility of using microlensing to identify ICoRs. In a previous paper we described a simulation of neutron star evolution in phase space in the Galaxy, taking into account the distribution of the progenitors and the kick at formation. Here we first reconsider the evolution and distribution of neutron stars and black holes adding a bulge component. From the new distributions we calculate the microlensing optical depth, event rate and distribution of event time scales, comparing and contrasting the case of ICoRs and "normal stars". We find that the contribution of remnants to optical depth is slightly lower than without ...
For an assessment of the future US spallation neutron source (SNS) target performance, radiation induced hardening and microstructural evolution were investigated as a function of ion dose for EC316LN stainless steel. Irradiation was carried out using 3.5 MeV Fe{sup +}, 360 keV He{sup +}, and 180 keV H{sup +} simultaneous ion-beams at 200 deg. C to simulate the damage, He and H production in the SNS target vessel wall. At low dose (< 1 dpa), the predominant defects were black dots whose number density saturated rapidly within a few dpa. This was followed by the evolution of interstitial loops whose number density saturated below 15 dpa. Although He-bubbles were not visible, severely scalloped loops suggested that the implanted He/H atoms existed in the form of small clusters. Comparison with reported neutron irradiation data showed that hardening and ductility loss occurred mostly in the black dot regime (< 1 dpa), but that good ...
For an assessment of the future US spallation neutron source (SNS) target performance, radiation induced hardening and microstructural evolution were investigated as a function of ion dose for EC316LN stainless steel. Irradiation was carried out using 3.5 MeV Fe"+, 360 keV He"+, and 180 keV H"+ simultaneous ion-beams at 200 deg. C to simulate the damage, He and H production in the SNS target vessel wall. At low dose (< 1 dpa), the predominant defects were black dots whose number density saturated rapidly within a few dpa. This was followed by the evolution of interstitial loops whose number density saturated below 15 dpa. Although He-bubbles were not visible, severely scalloped loops suggested that the implanted He/H atoms existed in the form of small clusters. Comparison with reported neutron irradiation data showed that hardening and ductility loss occurred mostly in the black dot regime (< 1 dpa), but that good ductility (>20% ...
In the fuel testing facilities of Japan Atomic Energy Research Institute, the post-irradiation test of practical fuel used in nuclear power stations was begun in December, 1979, and the soundness of practical fuel has been confirmed, and the valuable post-irradiation test data on the behavior of fuel have been acquired. Recently, the heightening of fuel burnup has been advanced, and also in fuel testing facilities, the development and preparation of the post-irradiation testing facility required for examining in detail high burnup fuel have been carried out. The course of the installation of the post-irradiation testing facility and the outline of the facility are reported. As the preparation of the post-irradiation testing facility for high burnup fuel, a hyperfine hardness tester that measures dynamic hardness, the measuring instrument for pellet thermal diffusion rate by laser flash method, the measuring instrument for pellet melting point ...
Abstract Thermomechanical behavior of membranes based on blends of poly(vinyl alcohol) (PVA) with different weight percentage (wt %) of glycerol has been studied. Solid-state PVA/Glycerol polymer membranes were prepared by a solution casting method. The films were studied for thermal characteristics by differential scanning calorimetry (DSC) and thermogravimetric analysis and for the mechanical properties including hardness and modulus by nanoindentation method. The dispersion of glycerol within the polymer matrix was examined using scanning electron microscopy. Fourier transform infrared spectroscopy was used to confirm the formation of hydrogen bonding between the plasticizer and PVA in their blends and also to provide information on compatibility and physical interactions between the gl...
It is shown that the usual proof of the second law of black hole physics breaks down if there are tachyons present in the vicinity of a black hole. Explicit cases are discussed where a tachyon of positive energy falling into the Kerr singularity actually decreases the area of the Kerr black hole. (author).
Tachyons fired into and absorbed by rotating black holes can violate the second and third laws of black hole physics. It is suggested that apparent break-downs of these laws in astrophysical black holes can indicate the existence of cosmic tachyons. (author).
Austenitic 316LN alloy was ion-irradiated using the unique Triple Ion Beam Facility (TIF) at ORNL to investigate radiation damage effects relevant to spallation neutron sources. The TIF was used to simulate significant features of GeV proton irradiation effects in spallation neutron source target materials by producing displacement damage while simultaneously injecting helium and hydrogen at appropriately high gas/dpa ratios. Irradiations were carried out at 80, 200, and 350 C using 3.5 MeV Fe{sup ++}, 360 keV He{sup +}, and 180 keV H{sup +} to accumulate 50 dpa by Fe, 10,000 appm of He, and 50,000 appm of H. Irradiations were also carried out at 200 C in single and dual ion beam modes. The specific ion energies were chosen to maximize the damage and the gas accumulation at a depth of {approximately} 1 {micro}m. Variations in microstructure and hardness of irradiated specimens were studied using transmission electron microscopy (TEM) and a nanoindentation ...
Effects of gamma irradiation on essential oils of five medicinal plants i.e. dried seeds of piper cubeba(cubeb), piper nigrum(black pepper), piper retrofractum, amomum cardamomum(cardamom) and myristica fragrans(mace), packed in low density polyethylene bag of 0.13 mm thickness have been investigated. After being irradiated at doses of 5 and 10 kGy, a part of the samples was analysed, and the rest were stored for six months at temperature of 30 +- 2 degC, and humidity ranging from 70 to 95%. The essential oil characteristics of control, irradiated and six month stored samples were analysed using infrared and ultraviolet spectrophotometers, HPLC, GLC and refractometer. Other parameters observed were moisture content and essential oil content of the samples. Results showed that irradiation up to a dose of 10 kGy do not give any significant effect on these parameters. Significant changes were only found in the essential oil content of piper ...
Aluminium nitride (AlN) is a very interesting ceramic because of its combination of properties such as high thermal stability, high hardness and an unusual combination of high thermal and low electrical conductivity. But it is very difficulty to obtain an AlN layer on the aluminium substrates by thermochemical nitriding process. Since a thin film of aluminium oxide existing on the surface of every aluminium substrate prevents the nitrogen atoms from diffusing into the aluminium lattice. However, it is possible to sputter the oxide film away from the aluminium surface in a glow discharge with the use of plasma nitriding technique and to allow the formation of AlN layer on the aluminium bulk. In the present work specimen of aluminium Al 99.5 has been plasma nitrided in a modified plasma nitriding unit, in which a diffusion pump was used to obtain an especially low partial pressure of oxygen in the vauum chamber. The sputter-cleaning prior to the nitriding was ...
Polarization measurements in the X-ray and gamma-ray energy range can provide crucial information on massive compact objects such as black holes and neutron stars. The Polarized Gamma-ray Observer (PoGO) is a new balloon-borne instrument designed to measure polarization from astrophysical objects in the 30-100 keV range, under development by an international collaboration with members from United States, Japan, Sweden and France. To examine PoGO's capability, a beam test of a simplified prototype detector array was conducted at the Argonne National Laboratory Advanced Photon Source. The detector array consisted of seven plastic scintillators, and was irradiated by polarized photon beams at 60, 73, and 83 keV. The data showed a clear polarization signal, with a measured modulation factor of $0.42 \\pm 0.01$. This was successfully reproduced at the 10% level by the computer simulation package Geant4 after modifications to its implementation of polarized ...
BackgroundFunctional Near-Infrared Spectroscope (fNIRs) is one of the latest technologies which utilize light in the near-infrared range to determine brain activities. Near-infrared...Full Text Available
To simulate radiation damage under a future Spallation Neutron Source (SNS) environment, irradiation experiments were conducted on a candidate 9Cr-2WVTa ferritic/martensitic steel using the Triple Ion Facility (TIF) at ORNL. Irradiation was conducted in single, dual, and triple ion beam modes using 3.5 MeV Fe{sup ++}, 360 keV He{sup +}, and 180 keV H{sup +} at 80, 200, and 350{degrees}C. These irradiations produced various defects comprising black dots, dislocation loops, line dislocations, and gas bubbles, which led to hardening. The largest increase in hardness, over 63 %, was observed after 50 dpa for triple beam irradiation conditions, revealing that both He and H are augmenting the hardening. Hardness increased less than 30 % after 30 dpa at 200{degrees}C by triple beams, compatible with neutron irradiation data from previous work which showed about a 30 % increase in yield strength after 27.2 dpa at 365{degrees}C. ...
Black Hole Drawing Credit: April Hobart, CXC Explanation: In the center of a swirling whirlpool of hot gas is likely a beast that has never been seen directly: a black hole....
Black Hole Drawing Credit: A. Hobart, CXC Explanation: In the center of a swirling whirlpool of hot gas is likely a beast that has never been seen directly: a black hole....
Black Hole Drawing Credit: A. Hobart, CXC Explanation: In the center of a swirling whirlpool of hot gas is likely a beast that has never been seen directly: a black hole....
Black Hole Drawing Credit: A. Hobart, CXC Explanation: In the center of a swirling whirlpool of hot gas is likely a beast that has never been seen directly: a black hole....
Glasses in the system (95-x) [0.25 Na2O-0.75 B2O3]-x P2O5-5 Fe2O3 (0?x?15 mol%), have been prepared by the melt quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of P2O5 on the structure of the glass system. Elastic properties Poisson's ratio, micro-hardness and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz (both longitudinal and shear) at room temperature. The results showed that the density and the molar volume increase as both sound velocities and the determined glass transition temperatures decrease with increasing the contents of P2O5. Infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of P2O5 content as a second network former. These results are interpreted in terms of the replacement of the diborate units with B-O-B bridges by phosphate units with ...
The longitudinal-electric oscillations of the hot gluon system are studied beyond the well known leading order term at high temperature $T$ and small coupling $g$. The coefficient $\\eta$ in $\\omega^2 = m^2 \\, (1+ \\eta \\, g \\wu N \\, )$ is calculated, where \\hbox{$\\omega \\equiv \\omega (\\vc q =0)$} is the long-wavelength limit of the frequency spectrum, $N$ the number of colours and $m^2=g^2 N T^2/9$. In the course of this, for the real part of the gluon self-energy, the Braaten-Pisarski resummation programme is found to work well in all details. The coefficient $\\eta$ is explicitly seen to be gauge independent within the class of covariant gauges. Infrared singularities cancel as well as collinear singularities in the two-loop diagrams with both inner momenta hard. However, as it turns out, none of these two-loop contributions reaches the relative order $O(g)$ under study. The minus sign in our numerical result $\\; \\eta = -.18 \\; ...
The inverse problem of interpreting the SS 433 optical light curves is solved for a geometrically thick model accretion disk around the compact relativistic object: most likely a black hole.
A simple heuristic calculation is given for the rate of nucleation of black holes at positive temperature. This calculation is based on the classical theory of nucleation and reproduces the result of Gross, Perry, and Yaffe.
Significant ion irradiation during film growth is required for the formation of cubic boron nitride (cBN) films. Meanwhile, a huge level of intrinsic stress possibly induced by the ion bombardment has been frequently reported to result in cracking and/or lack of adhesion of deposited cBN films. The present work has been performed to investigate the interfacial and/or the buffer layer structures with better matching to the cBN film by relaxation of the film stress using ion-beam-assisted deposition (IBAD). Boron nitride films have been synthesized on Si(100) wafer and tungsten carbide (WC) substrates by depositing boron vapor under simultaneous bombardment with nitrogen ions and nitrogen-argon mixture ions in the energy range of 0.5-10 keV. Cubic BN films with enhanced tribological properties have been explored by inserting a BN layer with various B/N compositions as a controlled buffer at the interface. Significant relaxation of the film stress has been observed for the buffer layer ...
High-resolution near-infrared and far-infrared observations are presented of the southeastern molecular cloud fragment in the IC 5146 dark cloud. These observations rule out earlier suggestions for the formation of massive stars in this fragment.
Clicking on the image will bring up the highest resolution version available. The Whirlpool Galaxy in Infrared Dust Credit: Infrared: NASA, ESA, M. Regan & B. Whitmore (STScI),...
The differences are highlighted of various aspects of behaviour of the luminescence signal from feldspar when stimulated by green light and when stimulated by infrared radiation. In respect of bleaching, a comparison is made of the influence of white light (daylight) on the two stimulated luminescence signals, as well as a comparison of the influence of infrared exposure on the green-stimulated signal with the influence of green exposure on the infrared-stimulated signal. The influence of preheating on the two stimulated signals is also compared. Light-emitting diode systems were used for both green and infrared stimulation. The observations are considered in relation to the mechanism relevant to green- and infrared-stimulated luminescence from feldspar. (author).
The differences are highlighted of various aspects of behaviour of the luminescence signal from feldspar when stimulated by green light and when stimulated by infrared radiation. In respect of bleaching, a comparison is made of the influence of white light (daylight) on the two stimulated luminescence signals, as well as a comparison of the influence of infrared exposure on the green-stimulated signal with the influence of green exposure on the infrared-stimulated signal. The influence of preheating on the two stimulated signals is also compared. Light-emitting diode systems were used for both green and infrared stimulation. The observations are considered in relation to the mechanism relevant to green- and infrared-stimulated luminescence from feldspar. (author).
Aerosols affect the radiative energy budget on both the regional and global scales. The wavelength-dependent aerosol optical depth (AOD) is a fundamental determinant of the amount by which extra-terrestrial incoming sunlight and outgoing terrestrial radiation are being attenuated in the atmosphere. The present study addresses the influence of local waste burning on aerosol characteristics, black carbon (BC) aerosol mass concentration and spectral solar irradiance using ground-based measurements over the tropical urban environment of Hyderabad, India. AOD has been observed to be maximum during burning days compared to normal days. Aerosol size spectra suggest bimodal distributions during pre-and post-burning periods and trimodal distributions during burning periods. Angstrom wavelength exponent estimated from spectral variation of AOD suggested dominance of accumulation mode particle loading during burning days compared to normal days. Diurnal variation of BC on ...
This data set contains data from in situ infrared thermometer measurements ... Surface temperature was measured using an Apogee Infrared Thermometer from 23 ...
Carbon black is widely used as an active filler in the rubber industry to improve the physical properties of rubber. The surface energy of carbon black is high compared to that of various elastomers like styrene?butadiene rubber (SBR), butadiene rubber (BR) and ethylene?propylene?diene rubber (EPDM). The work aims at reducing the surface energy of carbon black by modifying its surface for application especially in rubber blends. The present paper looks into the possibility of using plasma polymerisation of acetylene as a surface modification technique for carbon black in comparison with silica. Thermogravimetric analysis, wetting behaviour with various liquids of known surface tension and time of flight secondary ion mass spectrometry (ToF-SIMS) were used to characterise the carbon black b...
BackgroundThe epidemiology of avian influenza viruses (AIVs) in gulls is only partially known. The role of the world's most numerous gull species, the black-legged kittiwake (Rissa...Full Text Available
It is shown that the interaction of a class of positive energy tachyons decreases the area of the horizon of the T-S, delta = 3 metric even in the case of a reversible transformation (Msub(ir) = constant). This is a violation of the second law of black hole physics.
It is shown that the interaction of a class of positive energy tachyons decreases the area of the horizon of the T-S, delta = 3 metric even in the case of a reversible transformation (Msub(ir) = constant). This is a violation of the second law of black hole physics. (author).
This assessment of Queensland's resources of black coal has been prepared by the Coal and Oil Shale Resources Assessment and Development Subprogram, Queensland Department of Mines, in accordance with the 'Code for Reporting of Identified Coal Resources and Reserves'.
Background and objectives: Blacks are over-represented among dialysis patients, but they have better survival rates than whites. It is unclear if the over-representation of blacks on dialysis is due...Full Text Available
An analysis is made of the manner in which the process of primordial black-hole formation and the subsequent accretion of gas depend on the equation of state. On the assumption that the process is spherically symmetric, the problem is solved numerically.
This Final Technical Report provides an account of the project for the demonstration of Black Liquor Gasification at Georgia-Pacific LLC's Big Island, VA facility. This report covers the period from May 5, 2000 through November 30, 2006.
Black Hole Credit: April Hobart, CXC Explanation: In the center of a swirling whirlpool of hot gas is likely a beast that has never been seen directly: a black hole....
Hard Nano-Strutural Coatings Resistant to the Extreme Conditions of Chemical, Abrasive and High Energy Media for Thermonuclear Power, Oil and Gas and Chemical Industries
The fatigue and fracture behavior of hard tissues are topics of considerable interest today. This special group of organic materials comprises the highly mineralized and load-bearing tissues...Full Text Available
In-situ sodium activated organo modified bentonite clay was also used for partial replacement of the carbon black (N330). Detailed study with the black filled compound revealed that, with slight modification of the curing package, up to 10 phr of the carbon black replacement is possible. At equivalent loading of 5 and 10 phr of in-situ sodium activated organo modified bentonite clay exhibited better properties in comparison to carbon black filled compound.
We study the risk premium impact in the Perturbative Black Scholes model. The Perturbative Black Scholes model, developed by Scotti, is a subjective volatility model based on the classical Black Scholes one, where the volatility used by the trader is an estimation of the market one and contains measurement errors. In this article we analyze the correction to the pricing formulas due to the presence of an underlying drift different from the risk free return. We prove that, under some hypothesis on the parameters, if the asset price is a sub-martingale under historical probability, then the implied volatility presents a skewed structure, and the position of the minimum depends on the risk premium $\\lambda$.
The paper deals with Hawking radiation related to non-static spherically symmetric black hole. Quantum corrections are incorporated using Hamilton-Jacobi method beyond semi-classical approximation. It is found that different order correction terms satisfy identical differential equation as the semiclassical action and are solved by a typical technique. It has been shown that with proper choice of the proportionality factors, one loop back reaction effect in the space time can be obtained. Finally, using the law of black hole mechanics, a general modified form of the black hole entropy is obtained considering modified Hawking temperature.
The thermodynamic characteristics of adsorption of sulfur-containing amino acids and their derivatives on the surface of graphitized thermal carbon black were calculated by the molecular statistical method. The parameters of the atom-atom potential function of intermolecular interaction between the S atom in amino acids and the graphite C atom were determined. It was shown that an intramolecular H-bond influenced the adsorption of amino acids on the surface of graphitized thermal carbon black.
The thermodynamic characteristics of adsorption of sulfur-containing amino acids and their derivatives on the surface of graphitized thermal carbon black were calculated by the molecular statistical method. The parameters of the atom-atom potential function of intermolecular interaction between the S atom in amino acids and the graphite C atom were determined. It was shown that an intramolecular H-bond influenced the adsorption of amino acids on the surface of graphitized thermal carbon black.
The Klein-Gordan equation in the background of the Schwarzschild curved space-time is considered and the scattering of radial tardyons and tachyons from a black hole is studied. It is shown that black holes of mass below 7x10/sup 14/g may contain bound states of tardyons of pion mass which will be unstable on account of the presence of an attractive r/sup -4/ term.
The Klein-Gordan equation in the background of the Schwarzschild curved space-time is considered and the scattering of radial tardyons and tachyons from a black hole is studied. It is shown that black holes of mass below 7x10"1"4g may contain bound states of tardyons of pion mass which will be unstable on account of the presence of an attractive r"-"4 term. (author).
The suggestion has been made that stars with collapsing iron cores may be unable to explode, and hence may generate black holes. The situation when the collapsing core is rotating and magnetized is investigated and it is tentatively concluded that these effects make the situation even more conducive to the formation of black holes. (auth)
The author considers the extraction of the electromagnetic energy from a charged black hole through charged tachyons. The 'generalized ergosphere' relative to tachyons is defined. It turns out that it is possible to extract energy with 100% efficiency (through reversible process) if the charged source (whether black hole or otherwise) is of finite size. Two explicit examples of energy extraction are discussed. (Auth.).
The eastern oyster (Crassostrea virginica) developed neoplastic disorders when experimentally exposed both in the laboratory and field to chemically contaminated sediment from Black Rock Harbor (BRH),...Full Text Available
The standard postulates of general relativity are modified by allowing changes of topologies in space-time, i.e. considering a multiply-connected manifold. This allows, for instance, a different description of black holes and, in particular, a more rigorous approach to previous work studying the connections between black holes and tachyons. (author).
Glasses in the system (95-x) [0.25 Na{sub 2}O-0.75 B{sub 2}O{sub 3}]-x P{sub 2}O{sub 5}-5 Fe{sub 2}O{sub 3} (0<=x<=15 mol%), have been prepared by the melt quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of P{sub 2}O{sub 5} on the structure of the glass system. Elastic properties Poisson's ratio, micro-hardness and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz (both longitudinal and shear) at room temperature. The results showed that the density and the molar volume increase as both sound velocities and the determined glass transition temperatures decrease with increasing the contents of P{sub 2}O{sub 5}. Infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of P{sub 2}O{sub 5} content as a second network former. These results are ...
The present communication deals with the synthesis, single crystal growth and characterization of a new nonlinear optical material L-proline strontium chloride monohydrate (L-PSCM). Single crystals have been grown using the slow solvent evaporation technique. Single crystal XRD analysis confirmed that the crystal belongs to the orthorhombic structure with lattice parameter a=6.6966(3) A, b=12.4530(5) A, c=15.2432(5) A and space group P2_12_12_1. Presence of various functional groups in L-PSCM and protonation of the ions were confirmed by Fourier transform infrared spectroscopy (FT-IR) analysis. The melting point of the single crystal was found to be 126 "oC using DSC. Ultraviolet-visible spectral analyses showed that the crystal has low UV cut-off at 226 nm combined with very good transparency of 90% in a wide range. The optical band gap was estimated to be 5.82 eV. Capacitance and dielectric-loss measurements were carried out at different temperatures in the ...
One of vector-borne avian protozoa, Leucocytozoon lovati, has been found in the Japanese rock ptarmigans (Lagopus mutus japonicus), the endangered bird species distributed in the alpine regions in Japan. Vector arthropod species of L. lovati has also been estimated as Simuliidae black flies distributed in the same habitat of the host bird, however, possible blood meals of the black flies were not identified yet. To reveal host animals of black flies, we estimated the blood resources by using molecular techniques. Black flies were collected at Mt. Chogatake, one of the alpine regions of Japan in which Japanese rock ptarmigans live in June 2005. The analyzed 144 specimens were morphologically identified into five species including Simulium japonicum (n?=?87), Prosimulium hirtipes (n?=?48), P...
Condensed matter black hole analogues may provide guidance in grappling with difficult questions about the role of short distance physics in the Hawking effect. These questions bear on the very existence of Hawking radiation, the correlations it may or may not carry, the nature of black hole entropy, and the possible loss of information when a black hole evaporates. We describe a model of black hole formation and evaporation and the loss of information to a disconnected universe in a thin film of 3He-A, and we explain why the existence of Hawking radiation has not yet been demonstrated in this model. [We would like this article to be accessible to researchers in both condensed matter and gravitational physics, hence we include more than the usual amount of introductory material.
Samples of fat coal-E, its roof sandstone-A and blind coal-W from two coal mines in Hebei Province of China were brought to the laboratory to study the features of infrared thermal images and radiation temperature in the course of uni-axial load and uni-axial cycle load. To check the results of infrared remote sensing detection, two other methods, acoustic emission detection and electrical resistance detection were also used. The AGA-782 thermalvision detected change of the temperature field of the samples` surfaces. The study showed that: (1) coal rocks and sandstone in the course of loading have three types of infrared thermal image features and three types of infrared radiation temperature features; (2) infrared detection is comparable with acoustic emission detection and electrical resistance detection. Generally, the infrared forewarning of coal rocks` ...
ObjectivesWe have developed an image-guided surgery system based on invisible near-infrared (NIR) fluorescent light. Presently, the only clinically-available NIR...Full Text Available
The polarity of biological mediums controls a host of physiological processes such as digestion, signaling, transportation, metabolism, and excretion. With the recent widespread use of near-infrared...Full Text Available
The fraction of a given area of ground that is covered by hail can be determined by using an airborne infrared thermometer. If the ambient ground temperature and the hail-covered ground temperature are measured with the same thermometer, and the surface o...
BackgroundFourier Transform Infrared Imaging (FTIRI) is used to investigate the amide anisotropies at different surfaces of a three-dimensional cartilage or tendon block. With the...Full Text Available
A short account is given of the difficulties encountered in temperature measurement of boundary layers and a comparison of two types of thermometers, an infrared radiometer and mercury in glass thermometer. (Author)
Surface temperature is measured with an infrared thermometer. Measuring Surface Temperature. Nine sample points are selected with a site of uniform land ...
... significant change of spontaneous radiation intensity. It is very sensitive technique allowing the observation of small changes of light absorption. ...
We present results from a comprehensive number of relativistic, time-dependent, axisymmetric simulations of the runaway instability of non-constant angular momentum thick discs around black holes. This second paper extends earlier results where only constant angular momentum discs were considered. All relevant aspects of the theory of stationary thick discs around rotating black holes, necessary to build the initial state in our simulations, are presented in great detail. The angular momentum of the discs is assumed to increase outwards with the radial distance according to a power law. The main simplifying assumptions of our approach are not to include magnetic fields and self-gravity in the discs. Furthermore, the dynamics of the spacetime is accounted for by computing the transfer of mass and angular momentum from the disc to the black hole through the event horizon : the evolution of the central ...
A multi-spectral Schottky barrier infrared detector array in which individual pixels of radiation from a remote radiating object are detected by two or more Schottky barrier infrared radiation detectors each having a different spectral response so as to provide a ''color'' discrimination for the array.
A multi-spectral Schottky barrier infrared detector array in which individual pixels of radiation from a remote radiating object are detected by two or more Schottky barrier infrared radiation detectors each having a different spectral response so as to provide a ''color'' discrimination for the array.
Luminescence stimulated from feldspars using wavelengths in the infrared region can be applied to the dating of sedimentary grains. Reported stimulation spectra are very similar for a wide range of feldspars, but their emission spectra show greater variation. For accurate dating it is critical that unstable infrared-stimulated luminescence (IRSL) signals are removed from the laboratory-irradiated grains. Several approaches to isolate a thermally stable signal are described. (author).
We analyse in detail the SL(2, R) black hole by extending standard techniques of Kac-Moody current algebra to the non-compact case. We construct the elements of the ground ring and exhibit W_#infinity# type structure in the fusion algebra of the discrete states. As a consequence, we can identify some of the exactly marginal deformations of the black hole. We show that these deformations alter not only the spacetime metric but also turn on non-trivial backgrounds for the tachyon and all of the massive modes of the string. (orig.).
By employing the higher dimensional version of the Wu-Yang Ansatz we obtain magnetically charged new black hole solutions in the Einstein-Yang-Mills-Lovelock (EYML) theory with second ($\\alpha2$) and third ($\\alpha3$)order parameters. These parameters, where $\\alpha2$ is also known as the Gauss-Bonnet parameter, modify the horizons (and the resulting thermodynamical properties) of the black holes. It is shown also that asymptotically, these parameters contribute to an effective cosmological constant -without cosmological constant- so that the solution behaves de-Sitter (Anti de-Sitter) like.
Given a Schwarzschild black-hole, the frame sigma at rest with respect to the Schwarzschild metric are chosen as reference-frames. In this locally non-inertial frames, a free falling body is shown to reach the speed of light on the horizon and then to travel faster-than-light inside the horizon. The usual Szekeres-Kruskal (SK) coordinates represent themselves frames that (with respect to the frames sigma) travel at subliminal speed outside, at luminal speed on, and at superluminal speed inside the horizon (so that SK frames always describe any free falling body as a standard, slower-than-light object). At last, black-holes are shown to be possible sources of tachyons.
... after Roscoe Robinson relinquished command of the 82nd Airborne Division in 1978, it would be 25 ... taking command of the 10th Mountain Division. ...
... The addition of 0.5 pphr of fine thermal carbon black to the polymers gave good resistance to 500 hours of ultraviolet (UV) xposure in a Weather ...
This paper presents a detailed characterization and rheometric property study of in-situ sodium activated, organomodified bentonite clay - styrene-butadiene rubber (SBR) nanocomposite. It was found that around 10phr loading was the optimum level for maximum effect of the organo clay. The WAXD data indicated that at higher loading there was formation of agglomerations in the matrix. It was found that organo clay compound exhibited lower maximum torque in comparison to equivalent amount of carbon black loaded compound. The nanocomposites were also used for partial replacement of N330 carbon black in a highly black loaded compound. Part replacement of the carbon black with nano-clay reduced the maximum rheometric torque in comparison to the control compound. Detail study revealed that with sl...
In vibration control field, magneto-rheological (MR) fluid dampers are semi-active control devices that have recently begun to receive more attention. This paper presents a nonlinear black-box model (BBM) and an inverse black-box model (IBBM) for the identification of a MR fluid damper and their application to design a novel force-sensorless control method for any damping system using that damper. The nonlinear model named 'black-box' is a simple direct modeling method which was designed based on fuzzy-neural technique. Characteristics of the damper in study are directly estimated through a fuzzy mapping system. In order to improve the model accuracy, neural network technique including back-propagation and gradient descent method were used to train the fuzzy parameters to minimize the mode...
No Kerr-like exact solution has yet been found in Chern-Simons modified gravity. Intrigued by this absence, we study stationary and axisymmetric metrics that could represent the exterior field of spinning black holes. For the standard choice of the background scalar, the modified field equations decouple into the Einstein equations and additional constraints. These constraints eliminate essentially all solutions except for Schwarzschild. For non-canonical choices of the background scalar, we find several exact solutions of the modified field equations, including mathematical black holes and pp-waves. We show that the ultrarelativistically boosted Kerr metric can satisfy the modified field equations, and we argue that physical spinning black holes may exist in Chern-Simons modified gravity only if the metric breaks stationarity, axisymmetry or energy-momentum conservation.
... The fuel proposed was a medium-thermal carbon black-liquid JP-i1 mixture. JP-iO or exo-tetrahydrodi (cyclopentadieue) is a pure hydrocarbon with ...
FIG. 4. Power Spectral Density of the MAP W11 radiometer. The red and black traces are the power spectral density measurements of the two detectors on the ...
We consider the simplest scenario when black strings (cigars) penetrate the cosmological brane. As a result, the brane has a Swiss-cheese structure, with Schwarzschild black holes immersed in a Friedmann-Lema\\^{\\i}tre-Robertson-Walker brane. There is no dark radiation in the model, the cosmological regions of the brane are characterized by a cosmological constant $\\Lambda$ and flat spatial sections. Regardless of the value of $\\Lambda$, these brane-world universes forever expand and forever decelerate. The totality of source terms in the modified Einstein equation sum up to a dust, establishing a formal equivalence with the general relativistic Einstein-Straus model. However in this brane-world scenario with black strings the evolution of the cosmological fluid strongly depends on $\\Lambda$. For $\\Lambda$ less or equal to zero it has positive energy density $\\rho$ and negative pressure $p$ and at late times it ...
Intensive work has long been going on to find out the unknown origin that sets off curious tribo-physicochemical phenomena and that causes various kinds of problems in oil-lubricated sliding contacts in mechanical and processing systems. The strange tribochemical reaction is one of the such curious chemical phenomena observed in the degradation of perfluoropolyether (PFPE) lubricating oil film in a hard disk drive. Plasma (triboplasma) (Nakayama and Mirza 2006 Tribol. Trans. 49 17) would be one of the most probable origins of the problems if it were generated sufficiently intensely in oil-lubricated sliding contacts, as it is in such a highly energetic state. The generation of plasma was predicted in both dry and oil-lubricated sliding (Nakayama 1997 Japan. J. Tribol. 42 1077, Nakayama 2004 Surf. Coat. Technol. 188-189 599). However, plasma generation in industrially important oil-lubricated contacts has not yet been proven, though it has been found in dry sliding ...
We present a study of the mid-infrared properties and dust content of a sample of 27 HII ``blobs'', a rare class of compact HII regions in the Magellanic Clouds. A unique feature of this sample is that even though these HII regions are of high and low excitation they have nearly the same physical sizes ~1.5-3 pc. We base our analysis on archival 3-8 microns infrared imagery obtained with the Infrared Array Camera (IRAC) on board the Spitzer Space Telescope. We find that despite their youth, sub-solar metallicity and varied degrees of excitation, the mid-infrared colors of these regions are similar to those of typical HII regions. Higher excitation ``blobs'' (HEBs) display stronger 8 micron emission and redder colors than their low-excitation counterparts (LEBs).
BackgroundThe hard clam, Mercenaria mercenaria, has been affected by severe mortality episodes associated with the protistan parasite QPX (Quahog Parasite Unknown)...Full Text Available
Sep 1, 2011 ... Title: Hardness, density, and shrinkage characteristics of silk-oak from Hawaii. Author: Youngs, R. L.. Date: 1964. Source: Research note FPL ...
The issue of beam-induced damage on diffractive hard X-ray optics is addressed. For this purpose a systematic study on the radiation damage induced by a high-power X-ray beam is carried out in both...Full Text Available
This report covers the test methods and equipment for testing aircraft armor both hard and soft. The hard armor are the typical ceramic type while the soft armor are various types of layered composite materials. 10 figs. (JEF)
The thermodynamic characteristics of adsorption on the surface of graphitized thermal carbon black at 300 K were determined by the molecular statistical method for three phenylalklylamines. The influence of the intramolecular H-bond on the conformation of the molecules compared with structurally related n-alkyl-benzenes was considered. It was shown that the conformations of the molecules could influence chromatographic retention. Conformational isomers stabilized by intramolecular H-bonds were found to retain their structure in adsorption on graphitized thermal carbon black.
The thermodynamic characteristics of adsorption on the surface of graphitized thermal carbon black at 300 K were determined by the molecular statistical method for three phenylalklylamines. The influence of the intramolecular H-bond on the conformation of the molecules compared with structurally related n-alkyl-benzenes was considered. It was shown that the conformations of the molecules could influence chromatographic retention. Conformational isomers stabilized by intramolecular H-bonds were found to retain their structure in adsorption on graphitized thermal carbon black.
Carbon Black and activated carbon materials providing high surface areas and a distinct pore distribution are prime materials for supercapacitor applications at frequencies < 0.5 Hz. A number of these materials were tested for their specific capacitance, surface and pore size distribution. High capacitance electrodes were manufactured on the laboratory scale with attention to ease of processability. (author) 1 fig., 1 ref.
Using the example of perhydrophenanthrene, perhydroanthracene and cyclopentanodecalin isomers a possibility is shown to use packed capillary columns containing graphitized thermal carbon black for a complete separation of high-boiling mixtures of polycyclic saturated hydrocarbon isomers in accordance with the geometric structure of their molecules.
The thermodynamic characteristics of adsorption of proline and its hydroxy derivatives on the surface of graphitized thermal carbon black (GTCB) were calculated. The arrangement of hydroxyl groups in the amino acid molecule was shown to influence their adsorption on GTCB. The influence of internal rotation angles in proline and its hydroxy derivative molecules on their adsorption on GTCB was studied.
The thermodynamic characteristics of adsorption of proline and its hydroxy derivatives on the surface of graphitized thermal carbon black (GTCB) were calculated. The arrangement of hydroxyl groups in the amino acid molecule was shown to influence their adsorption on GTCB. The influence of internal rotation angles in proline and its hydroxy derivative molecules on their adsorption on GTCB was studied.
Using an accretion-disk model, accretion disk luminosities are calculated for a grid of black hole masses and accretion rates. It is shown that, as the black-hole mass increases with time, the monochromatic luminosity at a given frequency first increases and then decreases rapidly as this frequency is crossed by the Wien cutoff. The upper limit on the monochromatic luminosity, which is characteristic for a given epoch, constrains the evolution of quasar luminosities and determines the evolultion of the quasar luminosity function. 22 refs.
Within the Westeuropean network of the electric current supply a continuing compensation is necessary with respect to the permanent alterations of capacity and frequency. Pumped-storage plants are of considerable significance to meet these requests. The Schluchseewerk AG, Freiburg/Breisgau, has among others five pumped-storage plants in the southern part of the Black Forest. The conception and the operation of them are described. (orig.).
Henry constants for the adsorption of o- and p-phenylenediamines on the surface of graphitized thermal carbon black within the temperature range 433?479 K were calculated by the molecular statistical method. The parameters of the atom-atom potential function of intermolecular interaction between the nitrogen atom in aniline and isomeric phenylenediamines and the carbon atom of the basal face of graphite were determined. It was shown that an intramolecular H bond influenced the geometry and adsorption properties of o-phenylenediamine.
Henry constants for the adsorption of o- and p-phenylenediamines on the surface of graphitized thermal carbon black within the temperature range 433-479 K were calculated by the molecular statistical method. The parameters of the atom-atom potential function of intermolecular interaction between the nitrogen atom in aniline and isomeric phenylenediamines and the carbon atom of the basal face of graphite were determined. It was shown that an intramolecular H bond influenced the geometry and adsorption properties of o-phenylenediamine.
We study the spin dependence of accretion onto rotating Kerr black holes using analytic techniques. In its linear regime, angular momentum transport in MHD turbulent accretion flow involves the generation of radial magnetic field connecting plasma in a differentially rotating flow. We take a first principles approach, highlighting the constraint that limits the generation and amplification of radial magnetic fields, stemming from the transfer of energy from mechanical to magnetic form. Because the energy transferred in magnetic form is ultimately constrained by gravitational potential energy or Killing energy, the spin dependence of the latter allows us to derive spin-dependent constraints on the success of the accreting plasma to expel its angular momentum. We find an inverse relationship between this ability and black hole spin. If this radial magnetic field generation forms the basis for angular momentum transfer in accretion flows, ...
Proper assessment of the hypothesis which correlates polycyclic aromatic hydrocarbons (PAHs) with the unidentified infrared emission bands requires additional experimental laboratory data. In order to address this need, thermal infrared emission studies were performed on a subset of PAHs suggested to be of astrophysical importance. It was proposed that infrared emission from interstellar PAHs occurs following absorption of an ultraviolet photon. Since energy transfer to the ground electronic state can be rapid for a species in which intersystem crossing is negligible, the emission spectrum may be viewed as resulting from an equilibrium vibrational temperature (Leger and d'Hendecourt, 1987). This has been the basis for using infrared absorption spectra to calculate the corresponding emission spectra at various temperatures. These calculations were made using room temperature infrared ...
Jul 21, 1998 ... Additional roof surface temperatures were taken with a handheld "heat spy," an infrared thermometer to help calibrate the ATLAS thermal ...
Apr 14, 2010 ... The payload uses a remote infrared thermometer (Kelvin-Video), a thermohygrometer (Iva-6A), a heat-loss thermoanemometer/thermometer (TTM-2) ...
There is a requirement for a noninvasive technique to monitor stem cell differentiation. Several candidates based on optical spectroscopy are discussed in this review: Fourier transform infrared (FTIR)...Full Text Available
light-emitting diode A light-emitting diode, or LED, is a semi-conductor light source that emits visible light or invisible infrared radiation. Semi-conductors ...
In this paper, a Kramers-Kronig (KK) analysis of infrared (IR) reflectance spectrum of quaternary In_0_._0_1Al_0_._0_6Ga_0_._9_3N film grown by molecular beam epitaxy (MBE) is reported. The infrared measurement is performed in the reflection mode at an incident angle of 15 degree sign by Fourier transform infrared (FTIR) spectroscopy at T = 300 K. The Kramers-Kronig analysis of the reflectivity data has been used to obtain the real and imaginary parts of the index of refraction (n and k), and the real and imaginary parts of the dielectric response function (#epsilon#' and #epsilon#') of the materials. Finally, the transverse optical and longitudinal optical phonons for quaternary In_xAl_yGa_1_-_x_-_yN were obtained.
May 1, 2011 ... Abstract: Diatek Corporation, San Diego, CA and the Jet Propulsion Lab developed the Diatek Model 7000 aural thermometer which weighs ...
A tunable diode laser is used to obtain infrared spectra of carbon dioxide in biological materials. The spectral resolution is sufficient to readily distinguish differing isotopic species. The technique may prove useful in clinical tests.
Cambridge scientists in the late 1980's. This same team, then headed by Professor John Baldwin, built the world's first separated-element optical/infrared aperture synthesis...
Comparative patterns of equilibrium adsorption of argon on the surface of graphitized thermal carbon black (GCB) and the inhomogeneous surfaces of nongraphitized carbon black and silica at 77 and 87.3 K were considered. It was shown that argon acquires the properties of a special phase with a layered structure and exhibits two-dimensional phase transitions with the formation of crystal-like layers near the homogeneous surface of GCB even at a temperature exceeding the triple point. However, already at a distance of three-four molecular diameters from the surface, adsorbed argon behaves as a bulk phase in a weak external field. The defect surface of nongraphitized carbon black and the amorphous surface structure of silica destroy the longrange order of adsorbed argon and lower its solidific...
We study perturbations of a Schwarzschild black hole in Chern-Simons modified gravity. We begin by showing that Birkhoff's theorem holds for a wide family of Chern-Simons coupling functions, a scalar field present in the theory that controls the strength of the Chern-Simons correction to the Einstein-Hilbert action. After decomposing the perturbations in spherical harmonics, we study the linearized modified field equations and find that axial and polar modes are coupled, in contrast to general relativity. The divergence of the modified equations leads to the Pontryagin constraint, which forces the vanishing of the Cunningham-Price-Moncrief master function associated with axial modes. We analyze the structure of these equations and find that the appearance of the Pontryagin constraint yields an overconstrained system that does not allow for generic black hole oscillations. We illustrate this situation by studying the case characterized by a ...
In vibration control field, magneto-rheological (MR) fluid dampers are semi-active control devices that have recently begun to receive more attention. This paper presents a black-box model (BBM) for identification of a MR fluid damper and its application to vibrating control systems using that damper with self-sensing behavior. A model named ''black-box'' is a simple direct modeling method which is designed for a typical MR fluid damper using the self-tuning fuzzy technique. The characteristics of the researched damper are directly estimated through a fuzzy mapping system. In order to improve the accuracy of the proposed model, the back propagation algorithm and gradient descent method were used to train the fuzzy parameters to minimize the model error function. Consequently, the BBM with ...
Stellar rotation velocities and velocity dispersions along three slit positions in M31 have been measured, and three-dimensional velocity and velocity dispersion fields are obtained in order to search for a central black hole. Synthetic apparent spectra are constructed to eliminate problems with the reaction of the Fourier quotient program to stellar population mixes. Models are constructed to explore parameter space. The large velocities and velocity gradients that are found imply that the total mass-to-light ratio rises sharply at r of 0.5 arcsec or less to values greater than 100. This is much larger than normal for old stellar populations. Velocity anisotropies are not a major uncertainty because of the rapid rotation. There is thus strong evidence for a dark central mass, probably a supermassive black hole. 48 references.
Purpose - This paper discusses the impact of aesthetic design of smartphones on users' emotional reactions and preferences towards the product. To this end, the paper presents a study that explores emotional reaction of males to varying aesthetic design of the BlackBerry and empirically evaluates their preferences for the BlackBerry in different colours and overlay patterns. The paper then presents the statistical results of the study in an innovative graphical representation. Design/methodology/approach - A quantitative and qualitative research design was used, including three types of data-collection instruments (direct observations, rating scales, and interviews) to investigate if males have a stronger positive emotional reaction for visually treated BlackBerry Pearl devices over the or...
Nuclear magnetic resonance (NMR) techniques coupled with multivariate data analysis were used to conduct monitoring of biochemical changes of black raspberry fruits at different stages of maturation and under various extraction and NMR dissolution solvent conditions: extraction with 50% methanol and D"2O as an NMR dissolution solvent, extraction with 50% methanol and 50% methanol-d"4 as an NMR dissolution solvent, and extraction with 100% ethyl acetate and 100% methanol-d"4 as an NMR dissolution solvent. Partial least-squares discriminant analysis reliably distinguished black raspberry fruits according to the maturation stage, whereby the relative levels of various compounds such as amino acids, organic acids, sugars and phenolic compounds were compared using analysis of variance. Sucrose ...
Assuming the hoop conjecture in classical general relativity and quantum mechanics, any observer who attempts to perform an experiment in an arbitrarily small region will be stymied by the formation of a black hole within the spatial domain of the experiment. This behavior is often invoked in arguments for a fundamental minimum length. Extending a proof of the hoop conjecture for spherical symmetry to include higher curvature terms we investigate this minimum length argument when the gravitational couplings run with energy in the manner predicted by asymptotically safe gravity. We show that argument for the mandatory formation of a black hole within the domain of an experiment fails. Neither is there a proof that a black hole doesn't form. Instead, whether or not an observer can perform measurements in arbitrarily small regions depends on the specific numerical values of the couplings near the UV fixed point. We further ...
An apparatus is described for measuring the total hemispherical emittance of pipes of a length suitable for use in a prototype solar collector. The calorimetric method used requires measurements of the temperatures of the surface of the test pipe and of a concentric outer cylinder and measurement of the electrical power used to heat the test pipe. Measurements were made of the total hemispherical emittance of black chrome, nickel, and bare steel pipes as a function of temperature. The emittance of the black chrome surfaces increased significantly from an extrapolated value of about 0.1 at 25 deg C to values on the order of 0.3-0.4 at 300 deg C. The extrapolated values for black chrome agreed with measurements made using other techniques at room temperature. The results for the nickel-plated pipe agreed with total emittance calculated from spectral reflectance data.
The peak flux relationship between hard X-rays and microwaves from solar flares is studied using about 400 events simultaneously recorded with the hard X-ray burst spectrometer on the SMM satellite and the Nobeyama 17 GHz radiometer. The data indicate that the hard X-ray and microwave peak fluxes correlate best for X-ray energies of less than about 80 keV for impulsive flares and greater than about 360 keV for extended flares. By postulating that electrons responsible for microwave emission at 17 GHz are those emitting hard X-rays at these photon energies, it is concluded that: (1) in impulsive flares, microwaves at about 20 GHz are emitted mainly by electrons of less than about 200 keV from a layer through which the electrons stream down into the thick-target hard X-ray source; and (2) in extended flares, microwaves are emitted mainly by MeV electrons trapped in a coronal loop or ...
The theoretical hardness against total dose of the six-transistor SRAM cell is investigated in detail. An explicit analytical expression of the maximum tolerable threshold voltage shift is derived for two cross-coupled inverters. A numerical method is used to explore the hardness of the read and write operations. Both N- and P-channel access transistors designs are considered and their respective advantages are compared. The study points out that the radiation hardness mainly relies on the technology. Results obtained with the very robust Gate-All-Around process are finally presented.
The major details of the inspection and replacement of the bearing journals on each of the four heat transport pumps (HTPs) at Wolsung nuclear generating station in Korea are presented in this paper. Investigation following fracture of one of the journals in 1985 revealed that it was excessively hard. The journal material (ASTM A296 CA 40) is considered to be prone to stress corrosion fatigue if the hardness exceeds Rc 40. In 1986 May, during a planned outage, the HTPs were disassembled, the journals were inspected, found to be excessively hard, and all were replaced. At the same time, the pump to motor couplings were all refurbished to ensure proper alignment.
High interelectrode voltage peaks have been observed simultaneously with the emission of hard X-ray bursts from a flash X-ray tube. The magnitude of the voltage peaks may exceed twice the initial charging voltage. It has also been observed that the discharge emits bursts of X-and P-band microwaves radiation which are coincident with the emission of the hard X-ray bursts. The results indicate that the microwaves and X-rays have a common origin in discharge plasma movements and an acceleration model for electrons in the plasma is presented as one possible explanation of the observed phenomena.
Hardness of beta-sialon with four different composition index values of 0.25, 0.50, 0.75 and 1.0 in the system Ni/sub 3/N/sub 4/-AlN-Al/sub 2/O/sub 3/ with the addition of 6% Y/sub 2/O/sub 3/ as sintering aid has been reported. These composition were pressureless sintered for 90, 180 and 270 min in nitrogen atmospheres at temperatures ranging from 1650 to 1800 deg. C. Highest hardness was achieved when the composition index was 0.25 was sintered for 270 minutes at 1750 deg. C. (author).
CH Cygni is a symbiotic star consisting of an M giant and an accreting white dwarf, which is known to be a highly variable X-ray source with a complex, two-component, spectra. Here we report on two Suzaku observations of CH Cyg, taken in 2006 January and May, during which the system was seen to be in a soft X-ray bright, hard X-ray faint state. Based on the extraordinary strength of the 6.4 keV fluorescent Fe K-alpha line, we show that the hard X-rays observed with Suzaku are dominated by scattering.
This study sought to examine the association between adolescents’ relationship with family and school and depressive symptoms across ethnic/racial groups (White, Black, Hispanic, and...Full Text Available
This article aims to open up the biographical black box of three experts working in the boundary zone between science, policy and public debate. A biographical-narrative approach is used to analyse...Full Text Available
Nastic responses in bean plants (Phaseolus vulgaris L. var. Black Valentine) occur rapidly when very low concentrations of picloram (4-amino-3,5,6-trichloropicolinic acid) are applied...Full Text Available
BackgroundThymoquinone (TQ) is a compound extracted from Black Caraway seeds of Nigella Sativa and is active against various cancers. Cisplatin (CDDP) is the most...Full Text Available
Striated muscle fibers from the body and tail myotomes of a fish, the black Mollie, have been examined with particular attention to the sarcoplasmic reticulum (SR) and transverse tubular (or T) system....Full Text Available
We have examined the association between cytokine, chemokine and growth factor concentrations with bacterial vaginosis (BV) in pregnant white and black women. A nested case-control analysis...Full Text Available
... Zeitschrift fur SaugetierkundeOnline publication date: 16-Sep-2010.DANIEL J. THOMPSON, DOROTHY M. FECSKE, JONATHAN A. JENKS, and ANGELA ... Hillscougarlong-distance dispersalmountain lionOklahomaPuma conc...
Factors potentially contributing to the lower incidence of Lyme borreliosis (LB) in the far-western than in the northeastern United States include tick host-seeking behavior resulting in fewer human...Full Text Available
A procedure for long lasting general anaesthesia in gulls (Larus sp.) is described. It is based on an initial basal intramuscular dose of pentobarbital sodium, supplemented if necessary by intravenous injection to effect of the same agent. Additional intr...
Racial and ethnic disparities in healthcare persist in the U.S. Although pain is one of the most prevalent and disabling symptoms of disease, only a few studies have assessed disparities in...Full Text Available
We have constructed models for the vertical structure of disks around a black hole of 10/sup 6/ M/sub sun/ at distances from it smaller than the tidal breakup radius. These disks are massive enough that nuclear burning occurs in their central layers.
We present the results of three-dimensional hydrodynamical simulations of the final stages of inspiral in a black hole-neutron star binary, when the separation is comparable to the stellar radius. We use a Newtonian Smooth Particle Hydrodynamics (SPH) code to model the evolution of the system, and take the neutron star to be a polytrope with a soft (adiabatic index G=2 and G=5/3) equation of state and the black hole to be a Newtonian point mass. The only non-Newtonian effect we include is a gravitational radiation back reaction force, computed in the quadrupole approximation for point masses. We use irrotational binaries as initial conditions for our dynamical simulations, which are begun when the system is on the verge of initiating mass transfer and followed for approximately 23 ms. For all the cases studied we find that the star is disrupted on a dynamical time-scale, and forms a massive (the disc mass is approximately 0.2 solar masses) ...
The deposition of platinum on various carbon blacks was carried out by forming active functional groups on the surface of the carbon support, and exchanging these active groups with different platinum complexes. Using H{sub 2}PtCl{sub 6} solution, an impregnation rather than an exchange takes place. However, using divalent platinum complexes [Pt(NH{sub 3}){sub 4}]{sup 2+}, a fast exchange takes place which leads to extremely small platinum particles highly dispersed on the surface of carbon black. A comparison of the catalytic activities of platinum supported on various carbon blacks was also carried out. The performances of PEFC (Polymer Electrolyte Fuel Cell) based on the process of the ion exchange are reported. (authors) 3 refs.
Primordial black holes are unique probes of cosmology, general relativity, quantum gravity and non standard particle physics. They can be considered as the ultimate particle accelerator in their last (explosive) moments since they are supposed to reach, very briefly, the Planck temperature. Upper limits on the primordial black hole number density of mass $M_{\\star} = 5 10^{14}$ g, the Hawking mass (born in the big-bang terminating their life presently), is determined comparing their predicted cumulative $\\gamma$-ray emission, galaxy-wise, to the one observed by the EGRET satellite, once corrected for non thermal $\\gamma$-ray background emission induced by cosmic ray protons and electrons interacting with light and matter in the Milky Way. A model with free gas emissivities is used to map the Galaxy in the 100 MeV photon range, where the peak of the primordial black hole emission is expected. The best gas emissivities and ...
We calculate the structure of accretion disks around Kerr black holes for accretion rates 0.001 - 10 M_sun/s. Such disks are plausible candidates for the central engine of gamma-ray bursts. Our disk model is fully relativistic and treats accurately microphysics of the accreting matter: neutrino emissivity, opacity, electron degeneracy, and nuclear composition. The neutrino-cooled disk forms above a critical accretion rate that depends on the black hole spin. The disk has the ``ignition'' radius r_ign where neutrino flux rises dramatically, cooling becomes efficient, and the proton-to-nucleon ratio Y_e drops. Other characteristic radii are r_alpha where most of alpha-particles are disintegrated, r_nu where the disk becomes neutrino-opaque, and r_trap where neutrinos get trapped and advected into the black hole. We find r_alpha, r_ign, r_nu, r_trap and show their dependence on the accretion rate. We discuss the qualitative ...
Benzidine-based azo dyes are proven mutagens and have been linked to bladder cancer. Previous studies have indicated that their initial reduction is the result of the azo reductase activity of the intestinal...Full Text Available
OBJECTIVES. In this study we tested the association between occupational stress--as measured by job demands, decision latitude, and job strain--and hypertension in a population of 1396 Black and White...Full Text Available
... Optimisation of reactive dye removal by sequential electrocoagulation-flocculation... The removal of Reactive Black 5 dye in an aqueous solution by electrocoagulation (EC) as well... »Read more By M. Mohsen Nourouzi, T. G. Chuah, Thomas S....
The author demonstrates through a specific example that it is possible to extract rotational energy from a Kerr source (in principle, of arbitrary size but not turned black) through a reversible process by suitably injecting tachyons. (Auth.).
OBJECTIVE: The risk of cardiovascular and renal diseases has been shown to be higher for systolic blood pressure than diastolic blood pressure. The aim of this study was to assess the differential control...Full Text Available
BackgroundLifestyle, genetics and environmental factors are established determinants of bone density. We aimed to describe the bone characteristics of competitive top-ranked Nigerian...Full Text Available
Two cases of left ventricular aneurysm, a 16-year-old black boy and a 23-year-old white girl, from Bahia, Brazil, are presented. In both patients there was enlargement of the cardiac silhouette and...Full Text Available
... of Hanoi or Missionaries and Cannibals, It is not immediately obvious what constitutes a "move"--that is, what actual manipulations of the physical ...
Monolithic SiAlON ceramics are hard and brittle with little possibility for property design, but multi-phase SiAlON ceramics offer great scope for controlling microstructural development and desired properties. The ceramics can also be reinforced by separate additions of other hard, refractory compounds. The toughness in all these SiAlON composites can be increased by several mechanisms, and the best effect is reached if they are combined. When glassy phase is present, crack paths are affected by the strains caused by different thermal expansion of the glassy phase and the crystals and also by the interface properties. The crystal shape influence toughness, especially pronounced is the effect of the elongated #beta#- grains. Different toughening mechanisms are achieved by separately added reinforcement phases. The hardness is raised by the presence of #alpha# SiAlON and other hard constituents, such as ...
Counter-current regeneration of 2-stage sodium zeolite softeners has been employed in reducing hardness leakage level of steamflooding water to less than 1 ppm when raw water contains as much as 5,000 ppm of the total dissolved solids. Hardness leakage is caused by sodium displacement of calcium and magnesium from the bottom of the exchanger bed. This study presents nomographs providing for rapid calculations to be made, for which a convenient operational mode does not already exist. The nomographs relate the hardness leakage as a function of salt quality and influent water quality and present solutions for predicting the leakage level, salt quality requirement or the treatability of raw water required for steamflooding projects.
... interacting systems in which common-envelope evolutionary effects make it hard to generalize the results to single-star evolution, although they ...
BackgroundThe ongoing epidemiological transition in Mexico minimizes the relative impact of neurocysticercosis (NC) on public health. However, hard data on the disease frequency...Full Text Available
Necrotizing sialometaplasia, is a benign inflammatory lesion primarily involving the minor salivary glands of the hard palate. The lesion often presents itself as a deep-seated palatal ulcer with clinical...Full Text Available
Oct 30, 2009... of Belgian sheepherding dogs that are popular with the police and military. ... "She was a hard-working K-9 and she will be missed." ...
Interest in optics for hard X-ray broad-band application is growing. In this paper, we compare the hard X-ray (20-100 keV) reflectivity obtained with an energy-dispersive reflectometer, of a standard commercial gold thin-film with that of a 600 bilayer W/Si X-ray supermirror. The reflectivity of the multilayer is found to agree extraordinarily well with theory (assuming an interface roughness of 4.5 Angstrom), while the agreement for the gold film is less, The overall performance of the supermirror is superior to that of gold, extending the band of reflection at least a factor of 2.8 beyond that of the gold, Various other design options are discussed, and we conclude that continued interest in the X-ray supermirror for broad-band hard X-ray applications is warranted.
The salient features of the near-infrared free-electron laser (FEL) that is under construction at the new Darmstadt superconducting 130-MeV electron accelerator are discussed. Special attention is given to the layout and the parameters of the accelerator, the layout of the planned FEL experiment, the characteristics of the electron gun, the subharmonic chopper-buncher system, and the hybrid undulator system of the Darmstadt FEL. A comparison of the planned Darmstadt FEL with conventional lasers, with respect to the pulse and wavelength region, is presented. 15 refs.
A renormalization procedure is proposed which applies to lattice Feynman integrals containing zero-mass propagators and is analogous to the BPHZL renormalization procedure for continuum Feynman integrals. The renormalized diagrams are infrared convergent for non-exceptional external momenta, if the vertices of the theory satisfy a general infrared constraint. Under the same conditions as in the massive case, the continuum limit of the renormalized theory exists and is independent of the details of the lattice action.
Optical absorption measurements show that substitutional H"- ions, that is, protons with two electrons on anion sites, are thermally more stable than anion vacancies when thermochemically reduced CaO crystals are annealed in a reducing atmosphere. The H"- ions are identified by the infrared vibrational modes observed at 880 and 911 cm"-"1.
Dose-dependent behavior of the infrared stimulated luminescence (IRSL) decay from NaCl has been studied experimentally using only one aliquot irradiated with a range of 2-200 Gy {beta}-radiation doses. It was observed that the maximum IRSL intensity has not changed by an increase in dose though the total intensity increased as expected. Considering the possible implications of our findings for dosimeter, the results were compared with the other studies and discussed.
The generating functional in which the residual gauge freedom has been broken is related to the conventional generating functional for QED in arbitrary dimension. Closed expressions which relate ordinary N-point Green functions to N-point Green functions in the different gauges are derived. The leading logarithmic behaviour of the electron propagator in three dimensions is thus obtained. It is argued that one should not ascribe much importance to the infrared behaviour of the fermion propagator in the context of confinement.
The carbon content of silicon single crystals and polycrystals has been measured by charged particle activation analysis (CPAA) and infrared absorption. The authors obtained a linear relationship between the absorption coefficient at 605 cm/sup -1/ and the carbon content obtained by CPAA. They obtained a conversion factor of (1.00 +- 0.03) 10/sup 17//cm/sup 2/ for a 100% substitutional carbon.
The absolute absorption of ozone in the midinfrared has been measured relative to 253.7-nm ultraviolet absorption to an accuracy of 1% using a Bruker Fourier transform spectrometer. These new results agree with previous measurements by diode laser measurements after the latter are corrected for more recent infrared calculations and ultraviolet cross sections. They also agree with a determination based on refractive index measurements in the infrared. 16 refs., 4 figs., 3 tabs.
A black neutron detector of novel design has been constructed and tested as a neutron flux monitor. The neutron time-of-flight (TOF) technique was used to measure the zero degree neutron spectrum from a subnanosecond pulsed proton beam on a thick metallic lithium target. We describe the detector, discuss the shielding arrangement and electronics, determine the low-energy cut-off. We calculate the efficiency, show spectra and compare measured zero degree differential cross-section of the {sup 7}Li(p, n{sub 0}){sup 7}Be reaction with recommended published cross-sections. (orig.).
This paper introduces a new way of estimating parameters in a Brownian motion regime switching asset model to incorporate volatility clustering. The regime switching model is then applied to pricing of up-and-in barrier call options. We take the probability of crossing the barrier between simulation points into account, and we increase accuracy in simulations by importance sampling. The regime switching model is compared to the Normal Inverse Gaussian model and the traditional Black-Scholes model, and option prices from the regime switching model are compared to the closed form expression of up-and-in barrier calls in a Black-Scholes market.
The paper develops a new class of financial market models. These models are based on generalized telegraph processes: Markov random flows with alternating velocities and jumps occurring when the velocities are switching. While such markets may admit an arbitrage opportunity, the model under consideration is arbitrage-free and complete if directions of jumps in stock prices are in a certain correspondence with their velocity and interest rate behaviour. An analog of the Black-Scholes fundamental differential equation is derived, but, in contrast with the Black-Scholes model, this equation is hyperbolic. Explicit formulas for prices of European options are obtained using perfect and quantile hedging.
By comparison of standard entropies theoretically calculated and determined from gas-chromatographic data for 40 halo-aliphatic and halo-aromatic compounds 8 organic iodine compounds among them, adsorbed on graphitized thermal carbon black it was found that in all the cases the molecular model of ideal two-dimensional gas is a sufficiently good approximation. It was shown that for a number of systems the agreement can be improved if the vibrations of the center of molecular mass relative to the surface are taken into account
The adsorption of benzyl alcohol and 1-phenylethanol on graphitized thermal carbon black at 300 K is investigated. Thermodynamic characteristics of the adsorption of conformers stable in the gas phase and in the adsorbed state are determined by a molecular statistics method. The geometry of the molecules is optimized using the MP2 and B3LYP methods with a 6-311++G(d,p) basis set. Using the PBE0/6-31G(d) method, it is established that, in the adsorption of benzyl alcohol, two types of interactions, CH?O and OH??GTCB, occur. It is shown that, in 1-phenylethanol, intramolecular interactions are maintained.
We test the evolution of the correlation between black hole mass and bulge velocity dispersion (M{sub BH} - {sigma}), using a carefully selected sample of 14 Seyfert 1 galaxies at z = 0.36 {+-} 0.01. We measure velocity dispersion from stellar absorption lines around Mgb (5175 {angstrom}) and Fe (5270 {angstrom}) using high S/N Keck spectra, and estimate black hole mass from the H{beta} line width and the optical luminosity at 5100 {angstrom}, based on the empirically calibrated photo-ionization method. We find a significant offset from the local relation, in the sense that velocity dispersions were smaller for given black hole masses at z = 0.36 than locally. We investigate various sources of systematic uncertainties and find that those cannot account for the observed offset. The measured offset is {Delta} log M{sub BH} = 0.62 {+-} 0.10 {+-} 0.25, i.e. {Delta} log {sigma} = 0.15 {+-} 0.03 {+-} 0.06, where the error bars ...
The average angle of repose and the packing density of random planar heaps of hard disks falling ballistically onto a sticky base line, where the first layer of disks is quenched in random positions, are computed for heaps with a small fixed number of gaps in the base layer. The results we find appear to be almost independent of the size of the heap and they agree with those obtained from computer simulations of large systems.
The structure and properties of composite powder coatings on the base of titanium carbide are studied. It is shown the electron-beam welding deposition of powders on the base of nickel and titanium carbide allows to produce of high-quality wear-resistant coatings which superior in density and hardness compared with sputtered ones. Changes of hardening phase volume percentage as well as composition of metal matrix make possible to control coatings hardness
We explore the relationship between the hard X-ray photon index $\\Gamma$ and the Eddington ratio (\\xi=L_{X}(0.5-25 keV)/L_{Edd}) in six XRBs. We find that different XRBs follow different anti-correlations between $\\Gamma$ and $\\xi$ when $\\xi$ is less than a critical value, while they follow the same positive correlation when $\\xi$ is larger than the critical value. This anti-correlation and positive correlation are also found in LLAGNs and QSOs respectively, and the anti-correlation and positive correlation of different XRBs roughly converge to the same point ($\\log \\xi=-2.1, \\Gamma=1.5$), which may correspond to the accretion mode transition, since that the anti-correlation and positive correlation are consistent with the prediction of ADAFs and standard disk/corona system respectively. The traditional low/hard state are divided into two parts by the cross point $\\log \\xi\\sim-2.1$, i.e., faint-hard state in the ...
Micro-Vickers hardness measurement has been used to determine the composition of functionally graded materials (FGMs). Materials used in the present study are Al-SiC, Al-Shirasu and Al-Al{sub 3}Ni FGMs, which are fabricated by a centrifugal method. The micro-hardness of the aluminum matrix for Al-SiC FGM markedly increases as the volume fraction of SiC particles increases. However, the tendency is not so clear in the cases of Al-Shirasu and Al-Al{sub 3}Ni FGMs. Plastic strain energy due to thermal misfits between the matrix and dipersed particles is calculated based on an elasto-plastic analysis by applying a shell theory after Lee et al. The hardness is correlated theoretically with the composition gradient through the mean plastic strain energy (responsible for dislocation density). It is concluded that the composition gradient of metal-based FGMs can be determined from micro-hardness measurements. ...
Context: The colliding-wind binary Eta Car exhibits soft X-ray thermal emission that varies strongly around periastron, and non-thermal emission seen in hard X-rays and gamma-rays. Aims: To definitively identify Eta Car as the source of the hard X-ray emission, to examine how changes in the 2-10 keV band influence changes in the hard X-ray band, and to understand more clearly the mechanisms producing the non-thermal emission using new INTEGRAL observations obtained close to periastron. Methods: A Chandra observation encompassing the ISGRI error circle was analysed, and all other soft X-ray sources (including the outer shell of Eta Car itself) were discarded as likely counter-parts. New hard X-ray images of Eta Car were studied close to periastron, and compared to previous observations far from periastron. Results: The INTEGRAL component, when represented by a power law (with a photon index of 1.8), ...
We present mid-infrared spectro-imagery and high-resolution spectroscopy ofthe Orion bar and of a region in the Orion nebula. These observations have beenobtained in the Guaranteed Time with the Circular Variable Filters of the ISOcamera (CAM-CVF) and with the Short Wavelength Spectrometer (SWS), on board theEuropean Infrared Space Observatory (ISO). Our data shows emission fromamorphous silicate grains from the entire HII region and around the isolatedO9.5V star Theta2 Ori A. The observed spectra can be reproduced by a mixture ofinterstellar silicate and carbon grains heated by the radiation of the hotstars present in the region. Crystalline silicates are also observed in theOrion nebula and suspected around Theta2 Ori A. They are probably ofinterstellar origin. The ionization structure and the distribution of thecarriers of the Aromatic Infrared Bands (AIBs) are briefly discussed on thebasis of the ISO observations.
A method for preparing metal for heating by infrared radiance to enable uniform and consistent heating. The surface of one or more metal parts, such as aluminum or aluminum alloy parts, is treated to alter the surface finish to affect the reflectivity of the surface. The surface reflectivity is evaluated, such as by taking measurements at one or more points on the surface, to determine if a desired reflectivity has been achieved. The treating and measuring are performed until the measuring indicates that the desired reflectivity has been achieved. Once the treating has altered the surface finish to achieve the desired reflectivity, the metal part may then be exposed to infrared radiance to heat the metal part to a desired temperature, and that heating will be substantially consistent throughout by virtue of the desired reflectivity.
This paper studies the effect upon the thermoluminescence (TL) signal of four feldspar samples of exposing them to infrared stimulation, as occurs during infrared-stimulated luminescence (IRSL) measurement. Together with pulse annealing measurements these results are used to show which part of the TL signal is removed by exposure to IR and which part is directly related to the IRSL signal that is observed. When the samples are preheated prior to measurement in order to remove any low-temperature (< 200"oC) TL signals, a linear relationship is observed between the amount of TL that is lost and the IRSL light sum that is produced. The IRSL light sum is consistently four times larger than the amount of TL that is lost. Three possible explanations are proposed for this, but no conclusive evidence could be obtained to support any of them. A close similarity is observed in the pulse annealing results and the loss of TL due to IR exposure of the ...
An experiment lasting a number of hours was carried out with 6 men under standardised climate chamber conditions to find out to what extent wallpaper that reflects about 65-75% in the infra-red range by comparison with normal wallpaper that reflect only 3-5% of heat, has measurable positive effects on the thermoregulation of the human body and the human sensation of temperature. The measurements of skin temperature and heat flow intensity in the deeper areas of the body and the periphery, and metabolic heat conversion measurements (indirect calorimetry) confirm that infra-red reflection of the heat irradiated from the body lead to a measurable heat recovery on the body surface with a reduction of metabolic conversion. It was proved that it is possible to reduce the average room temperature by up to 4 K whilst maintaining the same degree of thermal comfort, which corresponds to a 20% saving in heating energy. (orig./BWI).
This paper introduces a parallel measurement approach for fast infrared-based human temperature screening suitable for use in a large public area. Our key idea is based on the combination of simple image processing algorithms, infrared technology, and human flow management. With this multidisciplinary concept, we arrange as many people as possible in a two-dimensional space in front of a thermal imaging camera and then highlight all human facial areas through simple image filtering, image morphological, and particle analysis processes. In this way, an individual's face in live thermal image can be located and the maximum facial skin temperature can be monitored and displayed. Our experiment shows a measured 1ms processing time in highlighting all human face areas. With a thermal imaging ca...
The identification and characterization of carbonaceous materials (CMs) that control hydrophobic organic chemical (HOC) sorption is essential to predict the fate and transport of HOCs in soils and sediments. The objectives of this paper are to determine the types of CMs that control HOC sorption in the oxidized and reduced zones of a glacially deposited groundwater sediment in central Illinois, with a special emphasis on the roles of kerogen and black carbon. After collection, the sediments were treated to obtain fractions of the sediment samples enriched in different types of CMs (e.g., humic acid, kerogen, black carbon), and selected fractions were subject to quantitative petrographic analysis. The original sediments and their enrichment fractions were evaluated for their ability to sorb trichloroethene (TCE), a common groundwater pollutant. Isotherm results and mass fractions of CM enrichments were used to calculate sorption contributions of ...
Oct 20, 1997 ... The following requirements apply to the solar array: ..... housings will be coated with material meeting the program's outgassing requirements. ... The solar array temperature testing requirements will be determined by analysis. .... The ADS also generates attitude products for the project and science team. ...
Mar 2, 2011 ... CCT's software is capable of simultaneously handling incoming ... has been using CCTK to automate its remote control rocket cryogenic fueling systems. ... seismic, infrared, and proximity sensor data with auto-tracking ...
Jul 17, 2008 ... The first version uses a red-green-blue filter; the second, an infrared-green- blue. Videos credit: Donald J. Lindler, Sigma Space Corporation/GSFC; ... The video will help us connect a varying point of planetary light ...
We present photoelectric BVRI photometry for 16 T Tau and related stars in the Rho Oph dark cloud, as well as vidicon spectroscopic observations for nine stars. The color excesses of these stars favor circumstellar dust shells as the source of the observed infrared excesses.
IntroductionThe aim of this study was to evaluate the effects of red blood cell (RBC) transfusions on muscle tissue oxygenation, oxygen metabolism and microvascular reactivity in...Full Text Available
A new gadolinium chelating NIR fluorescent molecular probe increases T1 relaxivity of water protons, facilitating combined optical and magnetic resonance imaging.
Breath analysis is a powerful noninvasive technique for the diagnosis and monitoring of respiratory diseases, including asthma and chronic obstructive pulmonary disease (COPD). Nitric oxide...Full Text Available
We used the recuperation effect (see also 'Recuperation of infrared stimulated luminescence of feldspars' in this issue) for investigating the connection between infrared- and greenlight-stimulated luminescence (IRSL and GLSL) of feldspars by performing a 'double-bleach recuperation' experiment. A diode system was used for infrared (IR) stimulation, and a filtered-light unit for greenlight (GL) stimulation. Powdered feldspar samples (2 mg each) of known chemical characterisation from a mineral collection were used. After beta-irradiation with 180 Gy and storage in the dark for several weeks feldspar aliquots were bleached down to a residual level of {approx}1% of the initial level, first with IR and subsequently with GL. For both stimulations, detection of the stimulated luminescence was carried out in the near ultraviolet region (around 260-360 nm, peaked at 340 nm). Other aliquots were ...
We used the recuperation effect (see also 'Recuperation of infrared stimulated luminescence of feldspars' in this issue) for investigating the connection between infrared- and greenlight-stimulated luminescence (IRSL and GLSL) of feldspars by performing a 'double-bleach recuperation' experiment. A diode system was used for infrared (IR) stimulation, and a filtered-light unit for greenlight (GL) stimulation. Powdered feldspar samples (2 mg each) of known chemical characterisation from a mineral collection were used. After beta-irradiation with 180 Gy and storage in the dark for several weeks feldspar aliquots were bleached down to a residual level of #approx#1% of the initial level, first with IR and subsequently with GL. For both stimulations, detection of the stimulated luminescence was carried out in the near ultraviolet region (around 260-360 nm, peaked at 340 nm). Other aliquots were bleached in reverse order (1st GL, ...
BACKGROUND: Although the importance of lymphatic function is well recognized, the lack of real-time imaging modalities limits our understanding of its role in many diseases. In a phase...Full Text Available
Background and Objectives:Sound enamel manifests peak transparency in the near-IR (NIR) at 1310-nm, therefore the near-IR is ideally suited for high contrast imaging...Full Text Available
Ultra-luminous infrared galaxies are among the most luminous objects in the local universe and are thought to be powered by intense star formation. It has been shown that in these objects the rotational spectral lines of molecular hydrogen observed at mid-infrared wavelengths are not affected by dust obscuration, leaving unresolved the source of excitation of this emission. Here I report an analysis of archival Spitzer Space Telescope data on ultra-luminous infrared galaxies and demonstrate that star formation regions are buried inside optically thick clouds of gas and dust, so that dust obscuration affects star-formation indicators but not molecular hydrogen. I thereby establish that the emission of H_2 is not co-spatial with the buried starburst activity and originates outside the obscured regions. This is rather surprising in light of the standard view that H_2 emission is directly associated with star-formation ...
Assessment of subtle changes in the primary macromolecular components of cartilage, proteoglycan (PG) and collagen, is critical for the diagnosis of early stages of osteoarthritis (OA), but...Full Text Available
Phonological density refers to the number of words that can be generated by replacing a phoneme in a target word with another phoneme in the same position. Although the precise nature of the...Full Text Available
Most Vega-like stars have far-infrared excess (60micron or longward in IRAS, ISO, or Spitzer MIPS bands) and contain cold dust (~ 4% of the stars in nearby young stellar associations.
... days after it burned, using a portable spectroradiometer (704 bands in the range 0.35 to 2.5 mu m) and an infrared thermometer (one band, 6 to 14 mu m). ...
Context: Mild primary hyperparathyroidism (PHPT) is characterized by asymptomatic hypercalcemia, most commonly in the absence of classical signs and symptoms. Hence, there is need to characterize...Full Text Available
The description and results of the study on the free-electron laser (FEL) on 100 #mu#m, representing the first line of the FIAN multipurpose radiation complex, are presented. The electron beam with the energy of 6-8 MeV, once accelerated in a racetrack microtron and extracted into the FEL injection tract, is used for exciting this FEL. The system of the electron beam transport, injection and diagnostics are described. Additional works on increasing the beam emittance up to 0.4 A for one energy spread percent are carried out. The obtained electron beam parameters assure generation of the far infrared radiation in the FEL
Fourier Transform Infrared (FTIR) spectroscopy has been utilized during high rate E-beam evaporation/deposition of YBa2Cu3O7 (YBCO). The results demonstrate the great utility of FTIR as an in situ monitor of YBCO deposition and processing. We detect different (amorphous/fine polycrystalline) insulating pre-existing phases to the high Tc superconducting phase which appear to have distinct reflectivity fingerprints dominated by thin film interference effects, as a function of temperature and oxygen pressure. These fingerprints reveal some of the kinetic and thermodynamic pathways during the growth of YBCO.
In this paper we discuss recent work at the Advanced Technology Centre of BAE Systems on photonic technology, in particular photonic crystal fibres, applied to infra-red and electro-optic countermeasure systems. The use of Photonic Crystal fibres or holey fibres in countermeasure systems could significantly simplify platform integration by enabling remote location of laser sources, the generation of multiple wavelengths or continuum generation from a single pump source .The paper will describe the development of these fibres, drawing examples from recent civil collaborative research projects such as PFIDEL and LAMPS.
Hydroxyapatite samples were produced by two different wet-chemical methods, and characterized by x-ray diffraction, infrared and compression strength measurements. The x-ray diffraction measurements were simulated using the Rietveld method, and structural data as lattice parameters and average crystallite size were obtained. The infrared spectra showed the presence of CO$_3^{2-}$ ions in all samples, indicating a contamination by these ions. By mixing samples produced by both methods, a bioceramic was obtained and, after sintering, samples with very high compression strengths (26--30 MPa) were obtained.
Infrared (IR, 880 nm) stimulated luminescence (IRSL) signal was observed from quartz at room temperature. The characteristics of the signal such as its response to {gamma}-ray irradiation, thermal stability and thermal assistance energy show that the signal originates from different traps than those responsible for the luminescence signal stimulated by green light (GL, 514 nm). The IRSL signal's short lifetime (18 days at 15 deg. C) may have been the reason why it was not detected in previous experiments. The decay of the IR signal after GL illumination was observed. The thermoluminescence at 76 deg. C was enhanced after IR illumination.
Silicon nitride hybrid ball bearings used in high temperature applications undergo mechanical and environmental degradation. To study the surface chemistry of silicon nitride, a CAChe{trademark} Worksystem* has been used to generate the clusters and corresponding transmission vibrational spectra of silicon nitride. In the present study, the effect of surface conditions on the surface chemistry and wear degradation of silicon nitride was evaluated. Infrared reflection spectroscopy (IRRS) used to determine molecular orientations shows a difference in reflectance spectra for fractured and as-received.
BAE Systems is the leading producer of uncooled microbolometer based thermal imaging engines in the world. Initial investments to develop and produce uncooled infrared (IR) technology were primarily driven by military applications, but it was the commercial market with the potential for large product volumes which provided BAE Systems with the business model required for investment in uncooled IR technology. This paper reviews the heritage of BAE Systems technology and current products and is an example of the success of a Dual-Use technology area which DARPA invested in during the 1990s.
This paper describes a novel Fourier transform infrared (FTIR) spectroscopic method that can be used to rapidly screen soil samples from potentially hazardous waste sites. Samples are heated in a thermal desorption unit and the resultant vapors are collected and analyzed in a long-path gas cell mounted in a FTIR. Laboratory analysis of a soil sample by FTIR takes approximately 10 minutes. This method has been developed to identify and quantify microgram concentrations of explosives in soil samples and is directly applicable to the detection of selected volatile organics, semivolatile organics, and pesticides.
Comparative patterns of equilibrium adsorption of argon on the surface of graphitized thermal carbon black (GCB) and the inhomogeneous surfaces of nongraphitized carbon black and silica at 77 and 87.3 K were considered. It was shown that argon acquires the properties of a special phase with a layered structure and exhibits two-dimensional phase transitions with the formation of crystal-like layers near the homogeneous surface of GCB even at a temperature exceeding the triple point. However, already at a distance of three-four molecular diameters from the surface, adsorbed argon behaves as a bulk phase in a weak external field. The defect surface of nongraphitized carbon black and the amorphous surface structure of silica destroy the longrange order of adsorbed argon and lower its solidification temperature. Therefore, argon adsorbed at a temperature of 77 K, i.e., below the triple point, exhibits the properties of a ...
In this study, Reactive Red, Remazol Blue, and Reactive Black B removal capacities of Synechocystis sp. and Phormidium sp. were investigated. The microorganisms were cultivated in 100ml BG 11 medium and incubated at 30^oC under continuous illumination (12.5wm^-^2 (2400lx)) for 20 days in plant growth chamber. Trials were carried out at pH 9.5 for Reactive Red, pH 8.5 for Remazol Blue and Reactive Black B removal in media without and with triacontanol (TRIA). Removal capacities of Synechocystis sp. and Phormidium sp. were found higher in media containing TRIA. So that, Synechocystis sp. and Phormidium sp. removed Reactive Red with 25.7% and 35.4%, Remazol Blue with 37.5% and 25.5%, and Reactive Black B with 29.2% and 28.3% yield at 25mgl^-^1 dye concentrations, respectively. There is no rep...
Some authors have concluded that spiral structures and shocks do not develop if an adiabatic index gamma > 1.16 is adopted in accretion disc modelling, whilst others have claimed that they obtained well defined spirals and shocks adopting a gamma = 1.2 and a M_2/M_1 = 1 stellar mass ratio. In our opinion, it should be possible to develop spiral structures for low compressibility gas accretion discs if the primary component is a black hole. We considered a primary black hole of 8 solar mass and a small secondary component of 0.5 solar mass to favour spiral structures formations and possible spiral shocks via gas compression due to a strong gravitational attraction. We performed two 3D SPH simulations and two 2D SPH simulations and characterized a low compressibility model and a high compressibility model for each couple of simulations. 2D models reveal spiral structures existence. Moreover, spiral shocks are also evident in high ...
Single crystal tungsten oxide (WO3) nanoparticles were prepared via a microwave-assisted method. Electrochemical activity for hydrogen evolution reaction (HER) on WO3 supported on carbon black (WO3/C) electrocatalyst was first studied in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH) at room temperature. The overall experimental results revealed that the electrocatalytic activity for HER on WO3/C is one order magnitude higher than those obtained with carbon black in 0.5 M H2SO4 and is six times than in the case of carbon black in 1.0 M KOH. These results demonstrated that WO3 could enhance the electrocatalytic activity for hydrogen evolution reaction in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH). On the other hand, the kinetic reaction mechanisms were disc...
A Michelson interferometer and a CCD detector were used to measure the number of interference fringes related to the expansion length of rubber sample. The sample was situated in a microcryostat, and the temperature of the sample was varied from -200 .deg. C to +80 .deg. C. Various types of carbon black filled rubber (Duradene, Sn-SSBR) samples were used to determine the glass transition temperatures (T_g) and the thermal coeffcients (#alpha#). The mixing ratio was 0, 10, 30, 40, 50, or 70 parts per hundred of carbon black to Sn-SSBR rubber. For the unfilled rubber of Sn-SSBR, the T_g was about -24 .deg. C, and the thermal coeffcient was 1.18 X 10"-"4 .deg. C"-"1. The thermal coeffcients sharply increased around T_g for all samples, and decreased with increasing doping ratio of carbonblack from 0 .deg. C to 30 .deg. C. The volume resistivity was measured for natural rubber and EPDM rubber. They had maximum volume resistivities of 1.5 X 10"6 ...
In the paper, the effect of Ni content, WC grain size and Mo2C addition on WC-6.25wt%TiC-9.3wt%Ni cemented carbide were investigated to improve the properties of Ni-bonded cemented carbides. The results show that the decrease of Ni content will result in the decrease of transverse rupture strength and increase of hardness; with the decrease of WC particle size, hardness increases due to the refinement of WC grains, however, the transverse rupture strength decrease due to the decrease of Ni binder thickness; Mo2C proves to be an effective grain growth inhibitor. With the increase of Mo2C content, the WC grains are refined and the hardness and transverse rupture strength are improved. Generally, when the Ni content is decreased to 8.4wt%, 13.45mm WC is used and 1.2wt% Mo2C is added, a higher...
Microprocessor based ''smart'' pressure, level, and flow transmitters were tested to determine the radiation hardness of this class of electronic instrumentation for use in reactor building applications. Commercial grade Complementary Metal Oxide Semiconductor (CMOS) integrated circuits used in these transmitters were found to fail at total gamma dose levels between 2500 and 10,000 rad. This results in an unacceptably short lifetime in many reactor building radiation environments. Radiation hardened integrated circuits can, in general, provide satisfactory service life for normal reactor operations when not restricted to the extremely low power budget imposed by standard 4--20 mA two-wire instrument loops. The design of these circuits will require attention to vendor radiation hardness specifications, dose rates, process control with respect to radiation hardness factors, and non-volatile programmable memory technology. 3 ...
A study of the influence of the concentration of secondary addition, high concentrations of primary dopant, diffusion enhancer and stabilizer on radiation hardness is presented. It is concluded that the diffusion enhancing technique is the most powerful method for improving radiation hardness. A new polystyrene scintillator which contains 2% pT, 0.02% POPOP, 20% diffusion enhancer and 0.02% stabilizer gave 91% of initial light output immediately after 3 Mrad irradiation in air. Data are presented that show that scintillator prepared from commercial polymer is more radiation-hard and has greater light output than scintillator prepared from monomer. It is assumed that this difference is due to different molecular weight distributions. Some protocols for acceleration of aging (yellowing and crazing) are presented. It is shown that one of the main reasons for aging of plastic scintillators is residual monomer. 10 refs., 18 ...
A series of SiAlON materials with a cordierite-based matrix were annealed for different lengths of time to cause crystallization of the glass phase. Their fracture toughness, hardness, and elastic modulus were measured from room temperature up to 1100"0C. The fracture toughness generally decreased with temperature. Short time annealing raised toughness at lower temperatures, while further annealing lowered it back to the value for as-hot pressed materials. At higher test temperatures annealing had no effect on toughness. This annealing behavior is significantly different from that previously reported in the system SaAlON-YAG. Hardness decreased monotonically with temperature for all samples. Both hardness and the elastic modulus were not affected by the annealing treatment. At elevated temperatures appreciable scatter of modulus results allowed only a rough trend of decrease with temperature to be observed.
Molecular dynamics simulations have been carried out of the radial distribution function of the hard sphere fluid for a range of densities in the equilibrium fluid and just into the metastable region. The first derivative of the hard-sphere radial distribution function at contact was computed and its density dependence fitted to a simple analytic form. Comparisons were made with semi-empirical formulae from the literature, and of these the formula proposed by Tao et al (1992 Phys. Rev. A 46 8007) was found to be in best agreement with the simulation data, although it slightly underestimates the derivative at the higher packing fractions in excess of about 0.45. Close to contact, within a few per cent of the particle diameter, the radial distribution function can be represented well by a second order polynomial. An exponential function, which has some useful analytic features, can also be applied in this region.
PurposeThe purpose of this study was to determine the relationship between the changes of soft and hard tissues after modified anterior segmental osteotomy on the maxilla and mandible and to evaluate unintended facial changes using cephalometric and photometric analyses.Materials and MethodsThe subjects included 29 women and 1 man (22 to 50 years of age) who were diagnosed as bialveolar or bimaxillary protrusion and underwent modified anterior segmental osteotomy on the maxilla and mandible. Lateral cephalograms and lateral and frontal photographs taken preoperatively and postoperatively were analyzed.ResultsThere was a significant change in all soft and hard tissue parameters except the labiomental angle. The ratio of upper lip to maxillary incisor retraction was 0.67:1 and the ratio of l...
The introduction of tolerance to radiation (''radiation-hardness'') into large electronic systems is one of the major tasks to which this Handbook will be put. The practices recommended here for inculcating radiation-tolerance in equipment require advanced physical modeling techniques, precise engineering procedures, and firm assurance procedures. The degree to which these procedures should be used in an equipment project can be measured by the severity of the raw radiation environment, the desired reliability of the system, and the requirement of that project for radiation-sensitive technologies. The balance of device/circuit design versus shielding will depend on whether the radiation is highly penetrating -- as in isotope handling or military environments -- or readily attenuated, as in space. In this chapter the authors have attempted to summarize the essential features of the radiation hardening of large assemblies of equipment and how effective control of ...
Dense samples of #beta#-sialons (with z from 1 to 4) were pressuressly sintered for different time (15-240 minutes) and at relatively low temperature of 1600 C using single-phase #beta#-sialon powders synthesized by combustion nitridation. The samples were characterized using ultrasonic method for determination of elastic properties (E,G,#mu#). Also, hardness by Knoop and fracture toughness by Vickers indentation microfracture method was estimated. With increasing z number Young's modulus decreases from 293 to 179 GPa. Simultaneously Poisson ratio increases by about 30%. The highest values of hardness and fracture toughness were obtained for sialon with z equal to 1. (orig.).
Leptonic pair production on nuclei ad EMC-effect are discussed within the frames of the flucton model with scaling distortion. Cumulative production of direct photons and leptonic pairs as a test of the model of hard collisions is considered. The results of calculations of massive leptonic pair production cross sections on nucleus fluctons, caculations of the ratio of deuterium and iron structural functions, cross sections of direct photon production on sup(181)Ta nuclei at Esub(p)=400 GeV and cross section of #pi#-meson production in the model of hard collisions are presented. Experimental discovery of direct cumulative photons is concluded to be important for understanding the mechanism of parton hard scattering from nucleus fluctons.
Ceramic ball bearings of silicon nitride are used for hard disk drive (HDD) spindle motors, to increase seed, reliability and memory capacity of the HDDs. Silicon nitride ceramics have advantages of lightweight, high strength and hardness over the conventional steel for bearings, but is expensive. A new process of high cost performance has been developed for mass production of the small-size ceramic balls. The company plans to apply these bearings to higher devices, e.g., servers, for the time being, and to expand the applicable areas, e.g., common devices and other small-size motors. The ceramic bearings have been developed jointly with Koyo Seiko Co. Ltd. (translated by NEDO)
The Infrared Camera (IRC) is one of the scientific focal plane instruments on board the ASTRO-F infrared astronomical satellite. The IRC is designed for wide field imaging and slit-less spectroscopic observations at near- and mid-infrared wavelengths. The IRC consists of three channels; NIR, MIR-S and MIR-L, each of which covers wavelengths of 2-5, 5-12 and 12-26 micron, respectively. All channels adopt compact refractive optical designs. Large format array detectors (a InSb 512 x 412 array and two Si:As IBC 256 x 256 arrays) are employed. Each channel has 10 x 10 arcminutes wide FOV with diffraction-limited angular resolution of 70cm aperture of the liquid helium cooled telescope at wavelengths over 5 micron. A 6-position filter wheel is placed at the aperture stop in each channel, and has three band-pass filters, two grisms/prisms and a mask for dark current measurements. The 5 sigma sensitivity of one pointed observation ...
Behaviour of tachyons in gravitational field has been investigated by using imaginary as well as real superluminal Lorentz transformations. Using real superluminal transformations in four- and six-dimensional space-time, an expression for the gravitational force acting on a tachyon, moving along the tachyon corridor constructed to follow the tachyon geodesic, has been derived. The motion of a tachyon through a black hole has also been discussed and it is shown that the black hole acts like a gravitational tunnel for tachyons and the transition between the regions inside and outside the horizon can be understood as real superluminal transformations transforming a R"4=(r,t) world into a T"4=(t,r) world. 36 refs.. (author).
Even the presence of very low concentrations of dyes (1mgL-1) in the effluent is highly visible and is considered aesthetically undesirable. It must be removed from wastewater completely. This study systematically evaluates the performance of adsorption (three kinds of powdered activated carbons), coagulation (AlCl36H2O) and membrane (submerged hollow fiber microfiltration) processes individually in treating two kinds of reactive dyes (Orange 16 and Black 5) and then using a hybrid process with combined coagulation-adsorption-membrane treatment system. Adsorption capacity and kinetics of Orange 16 were much higher and faster than those of Black 5. The dye removal efficiency by coagulation was highly dependent on dye concentration and solution pH. The hybrid process performance was far more...
We investigate the existence of time-periodic solutions of the Dirac equation in the Kerr-Newman background metric. To this end, the solutions are expanded in a Fourier series with respect to the time variable $t$ and the Chandrasekhar separation ansatz is applied so that the question of existence of a time-periodic solution is reduced to the solvability of a certain coupled system of ordinary differential equations. First, we prove the already known result that there are no time-periodic solutions in the non-extreme case. Then it is shown that in the extreme case for fixed black hole data there is a sequence of particle masses $(m_N)_{N\\in\\mathbb N}$ for which a time-periodic solution of the Dirac equation does exist. The period of the solution depends only on the data of the black hole described by the Kerr-Newman metric.
In this study, the use of the weakly basic anion exchange resins of phenol-formaldehyde (Amberlyst A 23), polyacrylate (Amberlite IRA 67) and polystyrene (Lewatit MonoPlus MP 62) matrices for removal of the reactive dye Remazol Black B (RBB) from aqueous solution and wastewater were investigated. RBB sorption on the anion exchangers was a time dependent process. Color reduction percentiles of 75.2, 33.9 and 25.1% in wastewater treatment were found after 216 h of phase contact time with Lewatit MonoPlus MP 62, Amberlyst A 23 and Amberlite IRA 67, respectively. Inorganic salts and anionic surfactant action influenced RBB uptake by the anion exchangers. The amounts of dye retained by the anion exchangers increased with a rise in temperature. The maximum sorption capacities calculated from the...
Studies have been carried out to determine the possible physiological effects of contact with carbon black made by the thermal process. Contact was made by ingestion, skin application and/or inhalation. Ingestion and/or skin application do not appear to lead to any changes from the normal. Inhalation exposures do not produce pulmonary function changes (antemortem or postmortem studies) but may lead to moderate to severe "perifocal" emphysema in Rhesus monkeys (not observed in guinea pigs). Inhalation studies also suggest right ventricular septal and to a degree, left ventricular hypertrophy in Rhesus monkeys as an effect. Additional studies are necessary to support these finding and consideration must be given to the variability among exposed subjects as compared to controls. PMID:136503
On efficient glass capillary columns packed with graphitized thermal carbon black (GTCB) the stereoisomers of aromatic and saturated tricyclic hydrocarbons are completely separated and identified. The Henry's adsorption constants of the individual isomers were determined from mixture at different temperatures. Five isomers of perhydroanthracene, five isomers of perhydrofluorene, two isomers of perhydrophenalene, four isomers of perhydroacenaphthene, as well as phenalene, dihydrophenalene, acenaphthene and acenaphthylene were investigated. The increase of the hydrogenization degree of unsaturated tricyclic hydrocarbons reduces the retention. Among the saturated tricyclic isomers the retention becomes shorter with the larger bending of the molecules, i.e. from the molecule having more equatorial bonds to the molecules having more axial connections. The experimentally determined Henry's constants were qualitatively compared with the structure of the ...
The thermodynamic characteristics of adsorption (TCA) on the basal face of graphite have been calculated in terms of the semiempirical molecular statistical theory of adsorption for molecules of O-, S-, and Se-containing heteroadamantanes of different structure and isostructural cyclohexane derivatives. The influence of the nature, number, and position of heteroatoms in the adamantane framework on the TCA values was studied in detail, which made it possible to predict the retention of the compounds considered on the surface of graphitized thermal carbon black under the conditions of equilibrium gas adsorption chromatography. The introduction of each subsequent heteroatom into a polyheteroadamantane molecule makes a non-additive contribution to the TCA values. The contributions of various f...
The possibility of employing a number of adsorbents (polyphenylquinoxaline, Tenax GC, Carbopak C, graphitized thermal carbon black, silica gels modified with pyrocarbon or hexamethyldisilazane) for the trapping of organic traces from air has been investigated. Adsorption capacities of these adsorbents with respect to a number of volatiles released from certain plastics used as building material (polyvinylchloride, Relin, Acronal, etc.) have been measured. A number of the volatiles were identified by gas chromatography - mass-spectrometry after trapping on the adsorbents investigated. Chromatographic separation after trapping on the adsorbents was carried out on wall-coated open-tubular capillary columns as well as in capillary columns packed with graphitized thermal carbon black.
Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black and prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simulated Bayer digestion of Jamaican bauxite with added ferrours sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly wasted prior to electrodwatering to remove dissolved ions and decrease mud conductivities.
A historical overview is given on the basic results which appeared by the year 1926 concerning Einstein's fluctuation formula of black-body radiation, in the context of light-quanta and wave-particle duality. On the basis of the original publications (from Planck's derivation of the black-body spectrum and Einstein's introduction of the photons up to the results of Born, Heisenberg and Jordan on the quantization of a continuum) a comparative study is presented on the first line of thoughts that led to the concept of quanta. The nature of the particle-like fluctuations and the wave-like fluctuations are analysed by using several approaches. With the help of the classical probability theory, it is shown that the infinite divisibility of the Bose distribution leads to the new concept of classical poissonian photo-multiplets or to the binary photo-multiplets of fermionic character. As an application, Einstein's fluctuation formula is derived as a ...
In this paper, the effects of surface mediation on the adsorption isotherm and isosteric heat of adsorption on a graphite surface were investigated, as the surface mediation is known to affect the intermolecular interaction of adsorbed molecules close to the surface. Kim and Steele (Phys. Rev. B 45 (11) (1992) 6226-6233) and others have assumed that the surface mediation is confined only to the first layer. This will be tested in this paper with a combined experimental and Grand Canonical Monte Carlo (GCMC) simulation of adsorption of argon on graphitized thermal carbon black (GTCB) over a range of temperatures (77-95.25K). By matching the simulation results against the experimental data, we have found that the surface mediation is extended up to the fourth layer, rather than only the firs...
We study the dynamical evolution of a scalar field coupling to Einstein's tensor in the background of a Reissner-Nordstroem black hole. Our results show that the coupling constant #eta# imprints in the wave dynamics of a scalar perturbation. In the weak coupling, we find that with the increase of the coupling constant #eta# the real parts of the fundamental quasinormal frequencies decrease and the absolute values of imaginary parts increase for fixed charge q and multipole number l. In the strong coupling, we find that for l#not =#0 the instability occurs when #eta# is larger than a certain threshold value #eta#_c which deceases with the multipole number l and charge q. However, for the lowest l=0, we find that there does not exist such a threshold value and the scalar field always decays for arbitrary coupling constant.
The black carbon continuum is composed of a series of carbon-rich components derived from combustion or metamorphism and characterized by contrasting environmental behavior and susceptibility to oxidation. In this work, we present a micro-scale density fractionation method that allows isolating the small quantities of soot-like and graphitic material usually found in natural samples. Organic carbon and {delta}{sup 13}C mass balance calculations were used to quantify the relative contributions of the two fractions to thermally-stable organic matter from a series of aquatic sediments. Varying proportions of soot-like and graphitic material were found in these samples, with large variations in {delta}{sup 13}C signatures suggesting important differences in their origin and/or dynamics in the environment.
The adsorption of CO2 on a number of activated carbons, thermal carbon black, and oxide materials at 195 K was studied using static and dynamic techniques. The landing surface areas ?(CO2) ? 0.19 nm2 on thermal carbon black and the absolute values of sorption for P/P 0 < 0.4 were determined. The density of adsorbed CO2 in the micropore volume was estimated at ?(CO2) = 0.91 g/cm3. It was demonstrated that the previously found effect of a weakening of the sorption interaction of nitrogen molecules with thin-walled materials (which manifested itself in an analysis of sorption isotherms by a comparative method) was pronounced to a lesser degree for the sorption of CO2. At the same time, the presence of supermicropores in activated carbon samples resulted in overestimated values of surface area...
We study the phonon fluxes emitted when the condensate velocity crosses the speed of sound, i.e., in backgrounds which are analogue to that of a black hole. We focus on elongated one dimensional condensates, and on stationary flows. Our theoretical analysis and numerical results are based on the Bogoliubov-de-Gennes equation without any further approximation. The spectral properties of the fluxes and of the long distance density-density correlations are obtained, with and without an initial temperature. In realistic conditions, we show that the condensate temperature dominates the fluxes, and thus hides the presence of the spontaneous emission (the Hawking effect). We also explain why the temperature amplifies the long distance correlations which are intrinsic to this effect. This confirms that the correlations pattern offers a neat signature of the Hawking effect. Optimal conditions to observe the pattern are discussed.
In general relativity, the fields on a black hole horizon are obtained from those in the bulk by pullback and restriction. Similarly, in quantum gravity, the quantized horizon degrees of freedom should result from restricting, or pulling-back, the quantized bulk degrees of freedom. This is not yet fully realized in the - otherwise very successful - quantization of isolated horizons in loop quantum gravity. In this work we outline a setting in which the quantum horizon degrees of freedom are simply components of the quantized bulk degrees of freedom. There is no need to quantize them separately. We present evidence that for a horizon of sphere topology, the resulting horizon theory is remarkably similar to what has been found before.
The thermodynamic characteristics of adsorption of iodobenzene, 2-iodothiophene, and 1- and 2-iodoadamantanes on the surface of graphitized thermal carbon black were determined experimentally. The influence of the special features of the molecular structure of the adsorbates on the thermodynamic characteristics of adsorption was studied. The atom-atom approximation of the semiempirical molecular-statistical theory of adsorption was used to calculate the thermodynamic characteristics of adsorption of the adsorbates using the newly determined potential function parameters of pair intermolecular interaction (?( r)) of I with C atoms of the basal graphite face. For the example of isostructural monohalogenated benzenes, thiophenes, and adamantanes, a comparative analysis of the contributions of the F, Cl, Br, and I atoms to the thermodynamic characteristics of adsorption was performed for the nonspecific adsorption of these compounds on a plane graphitized carbon ...
A stiff skin forms on surface areas of a flat polydimethylsiloxane (PDMS) upon exposure to focused ion beam (FIB) leading to ordered surface wrinkles. By controlling the FIB fluence and area of exposure...Full Text Available
Investigations of superdense compression touch on such problems as ultrahigh-frequency oscillations of matter in the generation of gravitational waves, the powerful pumping of hard coherent radiation, and the laboratory simulation of stellar interiors. This paper reviews the theory of supercompression and discusses some experiments involving multifoil collision supercompression.
These sky images are scanned for point sources above a specified ... The threshold criteria are: a) Gold: >4 sigma in both the Soft AND Hard bands. b) Silver: ... Filtering: Currently, there is no plan for filtering within the GCN based ...
ObjectiveTo implement a role-reversal exercise to increase first-year pharmacy students' awareness of communication barriers in the health care setting, especially for deaf and hard-of-hearing...Full Text Available
ObjectivesPericardial tamponade after cardiac surgery is difficult to diagnose, thereby rendering timing of rethoracotomy hard. We aimed at identifying factors predicting the outcome...Full Text Available
ASTROSAT, India's first dedicated astronomy satellite is slated for launch in 2007. The primary science objective of ASTROSAT is to explore the Universe using broad-band instruments covering optical, UV, soft X-ray and hard X-ray studies
Plasma nitriding in glow discharge is a process of modifying surface properties of a material by which surface hardness, corrosion resistance, fatigue strength etc. of a material can be improved
BackgroundIn Trinidad and Tobago, the law on the mandatory use of seat belts was passed in 1995, but this law is hardly enforced. The objective of this study was to determine the...Full Text Available
This report discusses the following topics on superconductivity: nonlinearities in hard superconductors such as surface impedance of a type II superconductimg half space and harmonic generation and intermodulation due to alternating transport currents; and nonlinearities in superconducting weak links such as harmonic generation by a long Josephson Junction in a superconducting slab.
Ultra fine tungsten carbide and cobalt powders were milled by high energy planetary ball mill at different ball to powder weight ratios (BPR) to produce particles of WC-10wt%Co hard metal in nanometer scale size. Microstructural characterizations by TEM show that the particle size of tungsten carbide was achieved to 32nm after milling at 15 BPR during 10h. In order to reduce the WC grain growth during the sintering process, tantalum carbide was added to the hard metal as a WC grain growth inhibitor. The nano hard metal powders were compacted at 200MPa pressure and sintered at 1370-1450degreeC temperatures in a high purity hydrogen atmosphere. The results show that the addition of 0.6wt% of TaC improves the hardness and fracture toughness from 1493 HV30 and 11.8MPam (for TaC free sample) to...
Excimer laser processing enables both thermally-driven transformations and the incorporation of solutes into the surface of materials through melting and diffusional mixing. We have examined the effect of excimer laser processing on the microstructure and surface mechanical properties of titanium alloys. Changes in the surface hardness due to laser processing were studied using a Nanoindenter [trademark]. Alloying experiments using both mixing of evaporated surface layers of boron and laser gas alloying in air and in nitrogen all result in changes in the surface hardness of the material. Alloying with boron results in an amorphous surface which is somewhat harder than the as polished surface. Laser processing in air and pure nitrogen results in incorporation of oxygen and nitrogen and the development of fine ([approximately] 50 nm) precipitates of TiO and TiN respectively. Substantial increases in surface hardness result ...
Constraint-based lexical models of language processing assume that readers resolve temporary ambiguities by relying on a variety of cues, including particular knowledge of how verbs combine...Full Text Available
The October 2000 terrorist attack on the guided-missile destroyer USS Cole (DDG 67) in the port of Aden, Yemen, is commonly viewed in the larger context of al-Qa'ida's September 11th campaign. Beyond the initial official investigations, the military force...
The methods of surface modification of Ti-Zr alloy by laser treatment are considered. Characteristics of laser modification without- and with surface melting and with melting in different gaseous environments and with nickel microalloying are presented. Maximum depth, hardness and corrosion resistance are observed under nickel laser alloying.
An ex-employee's claims that inadequate enforcement of radiation safety regulations allowed excess radiation exposure thereby causing his deteriorating health was not substantiated by a thorough investigation.
Pressureless-sintered AlN and hot-pressed, pressureless-sintered and reaction-bonded SiC were neutron irradiated at temperatures between 100 and 785degC up to a fluence of 5.2 x 10"2"4 n/m"2. The hardness was increased by up to 51% in AlN and 84% in SiC. The hardness decreased after annealing at temperatures around the irradiation temperature. At the same temperatures, the macroscopic length, which was increased by irradiation, also began to decrease. The hardness and length were almost recovered after 1,200 #approx# 1,400degC annealing. Thus, hardening in irradiated AlN and SiC is controlled by the number of point defects, or, more precisely, by the strain caused by small point defect clusters which pin down dislocation movement. Dislocation loops were still observed in some samples after 1,400degC annealing while the hardness was almost recovered to that in the unirradiated state. Thus, the existence ...
BackgroundA goal of human genetics is to discover genetic factors that influence individuals' susceptibility to common diseases. Most common diseases are thought to result from the...Full Text Available
Plant surfaces covered with crystalline epicuticular waxes are known to be anti-adhesive, hardly wettable and preventing insect attachment. But there are insects that are capable of gluing their eggs...Full Text Available
68 replaced carbon steel piping in secondary system of pressurized water reactor (PWR) has been investigated by visual examination for checking thinning conditions. It is well known that the flow-accelerated corrosion (FAC) was inhibited by traces of Cr in steel. Therefore, the chemical compositions of those steels have been measured. In addition, the micro structure and hardness of those steels have been investigated. And the relationship between those material variables and FAC rate was considered. As the results, (1) The Cr contents in those steels were below 0.1 wt% except one sample. Minute quantities of chromium increase the resistance against FAC. But the water velocity was thought to be the dominant factor rather than chemical composition in steel, at least such as below 0.1%Cr. (2) Hardness of all piping has been satisfied the specifications of each materials. The hardness of steels was not correlated with wall ...
Previous ultrasound elasticity imaging experiments supported a generally accepted concept that the hardness of deep venous thrombi increases with thrombus aging. Results also showed that this...Full Text Available
The adhesive proteins secreted by marine mussels form a natural glue that cures rapidly to form strong and durable bonds in aqueous environments. These mussel adhesive proteins contain an unusual...Full Text Available
Deposition of hard coatings may influence the mechanical properties of the bulk material and its corrosion resistance. In this work we study the hardness of the coated and the back side of 100Cr6 steel plates. Electrochemical corrosion tests were performed in O{sub 2}-saturated acetate buffer of pH 5.6 at 25degC. Chromium nitride and titanium nitride coatings prepared by different physical vapour deposition processes, such as arc, thermionic arc evaporation, magnetron sputtering and ion-beam-assisted deposition (IBAD) were compared. The results show that, for sufficient corrosion protection, chromium nitride layers have to be thicker than 500 nm. An increased nitrogen partial pressure in the evaporation chamber of the IBAD process improves the corrosion resistance significantly. The hardness of the substrates was reduced in the case of thermoionic arc evaporation only, indicating a deposition temperature of more than ...
Laser surface alloying with gaseous nitrogen was utilized to improve the wear resistance of a Ti-6Al-4V alloy. Wear-resistant composite coatings reinforced by hard TiN dendrites were produced 'in-situ' on a substrate of a Ti-6Al-4V alloy. The hardness and wear resistance of the laser alloyed coating under two-body abrasive and block-on-ring full-sliding wear conditions were significantly enhanced. (orig.)
We report on measurements of radiation hardness of the plastic scintillating fiber SCSF-81. Fibers were irradiated with "6"0Co #gamma#-rays and fast neutrons up to 105 Gy and up to 5 x 1013 n/cm"2, respectively. Deterioration of the attenuation length of the scintillating fiber was studied. Some significant deterioration was observed at the integrated dose of about 1 x 103 Gy and at the integrated neutron flux (neutron fluence) of about 1 x 1012 n/cm"2 for #gamma#-ray and neutron irradiation, respectively. (author).
A flow field and particle trajectory in a HDD (Hard Disk Drive) between two rotating disks in axisymmetric enclosures is investigated using CFD code FLUENT/UNS. The RNG k-{epsilon} model is used as a turbulent model. In this study, the flow field between two disks are symmetric, and the flow field near the enclosure is very complex. Cross stream vectors are shown both for blowing and no blowing from the hub. The larger a particle, the more fast the particle deposits at the walls. In the case of blowing from the hub, the more fast the particle deposits at the walls. (author). 9 refs., 12 figs., 1 tab.
Wood-plastic combination (WPC) was produced by {gamma}-irradiation of persimmon impregnated with acrylonitrile and styrene. The hardness and strength of WPC obtained were higher than those of an unmodified wood. Thus, it was found that the WPC is suited for a head of golf club, because the Shore hardness value of WPC is 36% greater than that of unmodified wood. An impregnation method of monomers with some pigments could produce colored WPC without diminishing natural grain. Head of golf club could be manufactured from colored WPC in practice. (auhtor).
Wood-plastic combination (WPC) was produced by #gamma#-irradiation of persimmon impregnated with acrylonitrile and styrene. The hardness and strength of WPC obtained were higher than those of an unmodified wood. Thus, it was found that the WPC is suited for a head of golf club, because the Shore hardness value of WPC is 36% greater than that of unmodified wood. An impregnation method of monomers with some pigments could produce colored WPC without diminishing natural grain. Head of golf club could be manufactured from colored WPC in practice. (auhtor).
An interferometric technique for hard X-rays is presented. It is based on two transmission gratings and a phase-stepping technique, and it provides separate radiographs of the phase and absorption profiles of bulk samples. Tomographic reconstruction yields quantitative three-dimensional maps of the X-ray refractive index and of the attenuation coefficient, with a spatial resolution down to a few microns. The method is mechanically robust, it requires little monochromaticity, and can be scaled up to large fields of view. These are important prerequisites for use with laboratory X-ray sources. Numerous applications ranging from wave front sensing to medical radiography are presently under investigation.
Glow discharge plasma nitriding of AISI 304 austenitic stainless steel has been carried out for different processing time under optimum discharge conditions established by spectroscopic analysis. The treated samples were analysed by X-ray diffraction (XRD) to explore the changes induced in the crystallographic structure. The XRD pattern confirmed the formation of an expanded austenite phase (#gamma#_N) owing to incorporation of nitrogen as an interstitial solid solution in the iron lattice. A Vickers microhardness tester was used to evaluate the surface hardness as a function of indentation depth (#mu#m). The results showed clear evidence of surface changes with substantial increase in surface hardness.
The effects of variable hardness, pH, alkalinity, humics, and suspended clay on the chemical speciation of copper and its toxicity to fathead minnow larvae in Lake Superior water were investigated. Two proposed methods (toxicity factors and chemical speciation) for predicting LC50 values in specific natural waters from laboratory toxicity data and the average site specific values of general water quality parameters were evaluated. The accuracy of the cupric ion-selective electrode in determining CU/sup +2/ activities in ambient and chemically altered Lake Superior water was also determined.
The distributions of the effective numbers of 6q-fluctons in the energy, momentum and distance to the center of mass of nucleus are studied. Many characteristics of these distributions are shown to be universal, i.e. independent of the flucton size. The saturation of the flucton density in A > 80 nuclei and other peculiarities are found, which define different behavior of the effective numbers of fluctons and deuterons. This fact provides an explanation of the known underestimate by a factor of 1.5-6 of the cross sections of hard inclusive (p, p'd) process on nuclei calculated in the quasi-elastic approximation.
The world steel industry and market and the current status and prospects for the Japanese steel industry are discussed with particular reference to China, Europe, and the US. Trends in coking coal supply from Australia, Canada, and Mongolia and changes in demand for hard and semi-soft coking coals are considered. Canadian coal plays a significant role in the hard coking coal and PCI coal markets. This is expected to continue. Emerging concerns include the strong Canadian dollar and increases in fuel and materials costs. Canadian suppliers are asked to improve efficiencies, be competitive in the overall coal chain, and diversify their PCI coal reserves. 14 figs.
The efficiency of NbC on WC grain coarsening in a WC-10wt.%Co hardmetal alloy was demonstrated by hardness measurement and WC granulation observation. The heterogeneous and overall grain growth were controlled. A low temperature experimentally produced NbC was used and compared to the inhibition potential of a commercial NbC powder. The results were the same in terms of structural fineness and hardness. The dispersion of the experimental NbC was not a problem, in spite of its size. The experimental NbC has very large particles, formed by agglomerates of small crystallites. During milling these agglomerates could be broken down. (orig.)
We have implemented a virtual Young's double slit experiment for hard X-ray photons with micro-fabricated bi-prisms. We observe fringe patterns with a scintillator, and quantify interferograms by detecting X-ray fluorescence from a scanned 30nm Cr metal film. The observed intensities are best modeled with a near-field, Fresnel analysis. The maximum fringe number in the overlap region is proportional to the ratio of real to imaginary parts refractive index of the prism material. The horizontal and vertical transverse coherence lengths at beamline APS 8-ID are measured.
The effect of severe plastic deformation by cold high pressure torsion (HPT) on radio frequency (RF) plasma nitriding of pure iron, as well as St2K50 and X5CrNi1810 steels was investigated. Nitriding was carried out for 3 h in a nitrogen atmosphere at a pressure of 10"-"5 bar and temperatures of 350 and 400 deg. C. Nitrided specimens were analysed by scanning electron microscopy (SEM), X-ray diffraction and micro hardness measurements. It was found that HPT enhances the effect of nitriding leading almost to doubling of the thickness of the nitrided layer for pure iron and the high alloyed steel. The largest increase in hardness was observed when HPT was combined with RF plasma nitriding at 350 deg. C. In the case of pure iron, the X-ray diffraction spectra showed the formation of #epsilon# and #gamma#' nitrides in the compound layer, with a preferential formation of #gamma#' at the expense of the #alpha#-phase at the higher nitriding ...
The sera of NZB/BL mice have been found to be active in the complement fixation test against isogeneic liver antigens to a higher titre than the sera of CBA, C57BL and DBA/2 mice. Six sera from NZB...Full Text Available
If 4-day-old dark-grown zucchini squash seedlings (Cucurbita pepo L. cv. Black Beauty) are exposed briefly to red light, subsequent cell fractionation yields about 40% of the total...Full Text Available
A study has been made of the interaction between graphitized thermal carbon-black and cyclodextrins and a series of 28 derivatives of benzene (benzene, alkyl-, isoalkyl-, dialkyl-, trialkylbenzenes, vinyl-, and allyl-benzene). The specific retention volumes form the basis for a discussion of the mechanism of interaction and drawing conclusions for the practical separation of isomeric compounds. (orig.).
The wave equation of a spinless tachyon is studied in Schwarzschild space-time. In contrast to earlier approaches to the problem, it is shown that tachyonic static solutions satisfy a simple second-order linear differential equation regardless of the mass of the black hole and the mass parameter of the tachyon. Physical implication of the present approach is discussed. Using Langer modification of the WKB (Wentzel-Kramers-Brillouin) boundary condition an expression similar to the Bohr-Sommerfeld quantization condition is derived.
This report discusses the following topics: Prompt fission neutron energy spectra for {sup 235}U and {sup 239}Pu; Two-parameter measurement of nuclear lifetimes; ``Black`` neutron detector; Data reduction techniques for neutron scattering experiments; Inelastic neutron scattering studies in {sup 197}Au; Elastic and inelastic scattering studies in {sup 239}Pu; and neutron induced defects in silicon dioxide MOS structures.
The method and results of the quantitative gas chromatographic determination of volatile organic substances in an urban atmosphere are presented. The concentration of organic substances was determined by using a mixed adsorber consisting of graphitized thermal carbon black and activated charcoal modified by pyrocarbon. Average, maximum and minimum concentrations of constant organic components in the atmosphere of Leningrad as a typical large industrial city are reported.
Administration of minocycline (MN), a tetracycline antibiotic, produces a black pigment in the thyroids of humans and several species of experimental animals and antithyroid effects in rodents. We have previously shown that these effects appear to be related to interactions of MN with thyroid peroxidase (TPO), the key enzyme in thyroid hormone synthesis. In the present study, the mechanisms for inhibition of TPO-catalyzed iodination and coupling reactions by MN were investigated. 37 refs., 7 figs., 3 tabs.
Adsorption of ethylene and ethane on graphitized thermal carbon black and in slit pores whose walls are composed of graphene layers is studied in detail to investigate the packing efficiency, the two-dimensional critical temperature, and the variation of the isosteric heat of adsorption with loading and temperature. Here we used a Monte Carlo simulation method with a grand canonical Monte Carlo ensemble. A number of two-center Lennard-Jones (LJ) potential models are investigated to study the impact of the choice of potential models in the description of adsorption behavior. We chose two 2C-LJ potential models in our investigation of the (i) UA-TraPPE-LJ model of Martin and Siepmann for ethane and Wick et al. for ethylene and (ii) AUA4-LJ model of Ungerer et al. for ethane and Bourasseau et al. for ethylene. These models are used to study the adsorption of ethane and ethylene on graphitized thermal carbon black. It is found that the solid-fluid ...
A consistent combination of quantum geometry effects rules out a large class of models of loop quantum cosmology and their critical densities as they have been used in the recent literature. In particular, the critical density at which an isotropic universe filled with a free, massless scalar field would bounce must be well below the Planck density. In the presence of anisotropy, no model of the Schwarzschild black hole interior analyzed so far is consistent.
The author notes that if hadrons are gravitationally stabilized ``black holes``, as discrete physics suggests, it is possible that partons, and in particular quarks, could be modeled as tachyons, i.e. particles having v{sup 2} > c{sup 2}, without conflict with the observational fact that neither quarks nor tachyons have appeared as ``free particles``. Some consequences of this model are explored.
In this paper, we studied vapor-liquid equilibria (VLE) and adsorption of ethylene on graphitized thermal carbon black and in slit pores whose walls are composed of graphene layers. Simple models of a one-center Lennard-Jones (LJ) potential and a two-center united atom (UA)-LJ potential are investigated to study the impact of the choice of potential models in the description of VLE and adsorption behavior. Here, we used a Monte Carlo simulation method with grand canonical Monte Carlo (GCMC) and Gibbs ensemble Monte Carlo ensembles. The one-center potential model cannot describe adequately the VLE over the practical range of temperature from the triple point to the critical point. On the other hand, the two-center potential model (Wick et al. J. Phys. Chem. B 2000, 104, 8008-8016) performs well in the description of VLE (saturated vapor and liquid densities and vapor pressure) over the wide range of temperature. This UA-LJ model is then used in the study of ...
The performance of intermolecular potential models on the adsorption of benzene on graphitized thermal carbon black at various temperatures is investigated. Two models contain only dispersive sites, whereas the other two models account explicitly for the dispersive and electrostatic sites. Using numerous data in the literature on benzene adsorption on graphitized thermal carbon black at various temperatures, we have found that the effect of surface mediation on interaction between adsorbed benzene molecules must be accounted for to describe correctly the adsorption isotherm as well as the isosteric heat. Among the two models with partial charges tested, the WSKS model of Wick et al. that has only six dispersive sites and three discrete partial charges is better than the very expensive all-atom model of Jorgensen and Severance. Adsorbed benzene molecules on graphitized thermal carbon black have a complex orientation with ...
In this paper we investigate the effects of surface mediation on the adsorption behavior of argon at different temperatures on homogeneous graphitized thermal carbon black and on heterogeneous nongraphitized carbon black surface. The grand canonical Monte Carlo (GCMC) simulation is used to study the adsorption, and its performance is tested against a number of experimental data on graphitized thermal carbon black (which is known to be highly homogeneous) that are available in the literature. The surface-mediation effect is shown to be essential in the correct description of the adsorption isotherm because without accounting for that effect the GCMC simulation results are always greater than the experimental data in the region where the monolayer is being completed. This is due to the overestimation of the fluid-fluid interaction between particles in the first layer close to the solid surface. It is the surface mediation ...
Sulfuric acid and its partially or completely neutralized salts with ammonia are believed to result from the oxidation of sulfur dioxide in cloud water and in other heterogeneous media present in the atmosphere. Due to the natural abundance of ammonia and the ubiquitous presence of sulfur in the atmosphere, (NH/sub 4/)/sub 2/SO/sub 4/ is commonly the dominant chemical species in the ambient aerosol. The amounts of ammonium sulfates are expected to be very low in areas far removed from anthropogenic emissions of sulfur dioxide. The chemical composition of submicrometer aerosol particles was determined at the Mauna Loa Observatory (MLO) on Mauna Loa in Hawaii during an eight-day period in August 1986. The MLO site was selected for this measurement because it is the only ground-based aerosol observatory in the remote Pacific Ocean that allows extended sampling of aerosols in the free troposphere. Measurements were made using an attenuated total internal reflection (ATR) impactor system. ...
Nitromethane (CH(3)NO(2)) and its chlorinated analogue, chloropicrin (CCl(3)NO(2)), were photolyzed at 193, 248, and 266 nm, and the products were observed by time-dependent Fourier transform infrared emission spectroscopy. At 193 and 248 nm, the primary photodissociation pathway for nitromethane was cleavage of the C-N bond to produce CH(3) + NO(2)(A (2)B(2)). At 266 nm, weak emission was observed following photodissociation of nitromethane, but an infrared spectrum could not be obtained. The photodissociation of chloropicrin at 193 nm produced the analogous product channel CCl(3) + NO(2)(A (2)B(2)) in addition to several other product channels. At 248 and 266 nm, only CCl(3) + NO(2)(A (2)B(2)) was observed. The production of phosgene (CCl(2)O) from chloropicrin photodissociation was not observed in this study. PMID:16571044
A strong dependence of thermal activation energy (TAE) on infrared (IR) stimulation time for the infrared stimulated luminescence (IRSL) signal was observed for K-feldspar grains extracted from several sediments and granites from China. A TAE value as low as {approx}0.1 eV was observed at the beginning of IR stimulation and increased to {approx}0.45 eV after 90 s. For a trap depth of {approx}2 eV below the conduction band for the IRSL traps, the TAE value of {approx}0.45 eV is consistent with the energy gap between the excited states ({approx}0.5 eV below the conduction band) and conduction band. This phenomenon is explained as the result of the coexistence of thermally assisted recombination via conduction band or band-tail states hopping and athermal tunnelling recombination of electrons from the excited states under IR stimulation, leading to the observation of a higher anomalous fading rate in the initial part of the IRSL decay curve.
We present a Hubble Space Telescope image of the FRII radio galaxy 3C 401, obtained at 1.6 microns with the NICMOS camera in which we identify the infrared counterpart of the brightest region of the radio jet. The jet has a complex radio structure and brightens where bending occurs, most likely as a result of relativistic beaming. We analyze archival data in the radio, optical and X-ray bands and we derive its spectral energy distribution. Differently from all of the previously known optical extragalactic jets, the jet in 3C401 is not detected in the X-rays even in a long 48ksec X-ray Chandra exposure and the infrared emission dominates the overall SED. We propose that the dominant radiation mechanism of this jet is synchrotron. The low X-ray emission is then caused by two different effects: i) the lack of any strong external photon field and ii) the shape of the electron distribution. This affects the location of the synchrotron peak in the ...
We present our discovery of a narrow-line Baldwin effect, an anti-correlation between the equivalent width (EW) of a line and the flux of the associated continuum, in 5-20$\\mu$m mid-infared lines from a sample of 68 Active Galactic Nuclei (AGN), located at z$<$0.5, observed with the Infrared Spectrograph on the {\\it Spitzer Space Telescope}. Our analysis reveals a clear anti-correlation between the EW of the [SIV] 10.51$\\mu$m, [NeII] 12.81$\\mu$m, and [NeIII] 15.56$\\mu$m lines and their mid-IR continuum luminosities, while the Baldwin effect for [NeV] 14.32$\\mu$m is not as obvious. We suggest that this anti-correlation is driven by the central AGN and not circumnuclear star formation in the host galaxy. We also find that the slope of the narrow-line Baldwin effect in the mid-infrared does not appear to steepen with increasing ionization potential. Examining the dependence of the EW to the Eddington Ratio ($L/L_{Edd}$) we find no strong ...
We investigate the influence of lunar-like satellites on the infrared orbital light curves of Earth-analog extra-solar planets. Such light curves will be obtained by NASA's Terrestrial Planet Finder (TPF) and ESA's Darwin missions as a consequence of repeat observations to confirm the companion status of a putative planet. We use an energy balance model to calculate disk-averaged infrared (bolometric) fluxes from planet-satellite systems over a full orbital period (one year). The satellites are assumed to lack an atmosphere, have a low thermal inertia like that of the Moon and span a range of plausible radii. The planets are assumed to have thermal and orbital properties that mimic those of the Earth while their obliquities and orbital longitudes of inferior conjunction remain free parameters. Even if the gross thermal properties of the planet can be independently constrained (e.g. via spectroscopy or visible-wavelength detection of specular ...
The highly irradiated transiting exoplanet, HAT-P-7b, currently provides one of the best opportunities for studying planetary emission in the optical and infrared wavelengths. We observe six near-consecutive secondary eclipses of HAT-P-7b at optical wavelengths with the EPOXI spacecraft. We place an upper limit on the relative eclipse depth of 0.055% (95% confidence). We also analyze Spitzer observations of the same target in the infrared, obtaining secondary eclipse depths of 0.098+/-0.017%, 0.159+/-0.022%, 0.245+/-0.031% and 0.225+/-0.052% in the 3.6, 4.5, 5.8 and 8.0 micron IRAC bands respectively. We combine these measurements with the recently published Kepler secondary eclipse measurement, and generate atmospheric models for the day-side of the planet that are consistent with both the optical and infrared measurements. The data are best fit by models with a temperature inversion, as expected from the high incident ...
Context. We present a multi-wavelength, high-resolution observational survey of the young binary system Haro 6-10 (GV Tau, IRAS 04263+2426), which is harbouring one of the few known infrared companions. Aims. The primary goal of this project is to determine the physical and geometrical properties of the circumstellar and circumbinary material in the Haro 6-10 system. Methods. High-resolution optical (HST/WFPC2) and near-infrared (VLT/NACO) images in different bands were analysed to investigate the large-scale structures of the material around the binary.Mid-infrared interferometry (VLTI/MIDI) and spectroscopy (TIMMI2 at the 3.6m ESO telescope) were carried out to determine the structure and optical depth of the circumstellar material around the individual components. Results. The multi-wavelength observations suggest that both components of the binary system Haro 6-10 are embedded in a common envelope. The measured ...
In VHTGR (Very High Temperature Gas-cooled Reactor), the radiation plays an important role in heat transfer through the cavity in RCCS (Reactor Cavity Cooling System). We performed the series of experiments to measure the emissivity using the infrared thermometer with wavelength range of 8#approx#14 #mu#m. As the first step, the transmittance of Zinc Selenide (ZnSe) window was measured to estimate the emissivity that can compensate the attenuation effect of window. The kind of gas with various concentrations in the cavity will be released during postulated accidents to the coolant type, so it is essential to estimate the effects of gas on the measurement of emissivity. In this manner we measured the emissivity with the air, the helium and the steam inside chamber. The results represent that the concentration of the air and the helium do not affect the emissivity significantly while the steam decreases the measured emissivity relatively. It means that the air and ...
We search for an infrared signature of the transiting extrasolar planet HD 209458b during secondary eclipse. Our method, which we call `occultation spectroscopy,' searches for the disappearance and reappearance of weak spectral features due to the exoplanet as it passes behind the star and later reappears. We argue that at the longest infrared wavelengths, this technique becomes preferable to conventional `transit spectroscopy'. We observed the system in the wing of the strong nu-3 band of methane near 3.6 microns during two secondary eclipses, using the VLT/ISAAC spectrometer at a spectral resolution of 3300. Our analysis, which utilizes a model template spectrum, achieves sufficient precision to expect detection of the spectral structure predicted by an irradiated, low-opacity (cloudless), low-albedo, thermochemical equilibrium model for the exoplanet atmosphere. However, our observations show no evidence for the presence of this spectrum ...
the development of lithium metal batteries is hindered by the bad reversibility of the Li{sup +}/Li pair, due to dendrites formation which limits the amount of active matter and can generate short-circuits. The chemical and electrochemical phenomena which take place at the electrode/organic electrolyte interface lead to the formation of a complex passivation film which is of prime importance for the functioning of this type of batteries. The in-situ infrared reflection spectroscopy is well adapted to the chemical study of the passivation layer. Two different techniques were used: the substraction normalized interfacial transform infrared spectroscopy (SNIFTIRS) and the electro-chemically modulated infrared reflectance spectroscopy. These methods have shown that the passivation layer that develops on the surface of the lithium electrode in contact with organic solutions (propylene carbonate, ethylene carbonate and ...
We describe the flight performance of the cryogenic system of the infrared astronomical satellite AKARI, which was successfully launched on 2006 February 21 (UT). AKARI carries a 68.5 cm telescope together with two focal plane instruments, Infrared Cameras (IRC) and Far Infrared Surveyor (FIS), all of which are cooled down to cryogenic temperature to achieve superior sensitivity. The AKARI cryogenic system is a unique hybrid system, which consists of cryogen (liquid helium) and mechanical coolers (2-stage Stirling coolers). With the help of the mechanical coolers, 179 L (26.0 kg) of super-fluid liquid helium can keep the instruments cryogenically cooled for more than 500 days. The on-orbit performance of the AKARI cryogenics is consistent with the design and pre-flight test, and the boil-off gas flow rate is as small as 0.32 mg/s. We observed the increase of the major axis of the AKARI orbit, which can be explained by the ...
Microwave dielectric properties and far-infrared reflectivity spectra of (Zr{sub 0.8}Sn{sub 0.2})TiO{sub 4} ceramics with 1.0mol.% Sb{sub 2}O{sub 5} or WO{sub 3} were investigated in the various sintering atmospheres. The Q{center_dot}f value of the specimens sintered in oxygen atmosphere was enhanced due to the decrease of lattice anharmonic interaction resulting from the decrease of oxygen vacancies, whereas the dielectric constants remained constant regardless of sintering atmosphere. The effects of the sintering atmosphere on the changes of ionic and electronic polarization and the intrinsic microwave losses of the specimens were investigated by using the infrared reflectivity spectra from 50 to 4000cm{sup -1}, which were evaluated using Kramers-Kronig analysis and classical oscillator model. The relative tendency of microwave dielectric properties of the specimens calculated from the reflectivity data was in good agreement with the results ...
We present the discovery of a Baldwin effect in 8 nearby Seyfert galaxies for the three most prominent mid-infrared forbidden emission lines observable from the ground that are commonly found in AGN, [ArIII](8.99 micron), [SIV](10.51 micron), and [NeII](12.81 micron). The observations were carried out using the VLT/VISIR imager and spectroraph at the ESO/Paranal observatory. The bulk of the observed line emission comes from the inner <0.4 arcsec which corresponds to spatial scales <100 pc in our object sample. The correlation index is approximately -0.6 without significant difference among the lines. This is the strongest anti-correlation between line equivalent width and continuum luminosity found so far. In the case of Circinus, we show that despite the use of mid-infrared lines, obscuration by either the host galaxy or the circumnuclear dust torus might affect the equivalent widths. Given the small observed spatial scales from which ...
Abstract We address the fundamental question of matching the rest-frame K-band luminosity function (LF) of galaxies over the Hubble time using semi-analytic models after modification of the stellar population modelling. We include the Maraston evolutionary synthesis models, which feature a higher contribution by the thermally pulsating asymptotic giant branch (TP-AGB) stellar phase, into three different semi-analytic models, namely the De Lucia and Blaizot version of the Munich model, morgana and the Menci model. We leave all other input physics and parameters unchanged. We find that the modification of the stellar population emission can solve the mismatch between models and the observed rest-frame K-band luminosity from the brightest galaxies derived from UKIRT Infrared Deep Sky Survey d...
A diffuse-reflectance capability for the Fourier transform infrared spectrometer at the Y-12 Plant Laboratory has been implemented. A sample cell with a 25 to 400/sup 0/C temperature-controlled sample stage and an ultrahigh-vacuum-to-atmospheric pressure gas-handling capability has been developed. Absorbance of light from the spectrometer beam, resulting from the beam being scattered from a powder sample, can be measured. This capability of detecting molecular species on and in powders is to be used to study chemisorption on actinide and rare-earth metals, alloys, and compounds. Cell design is described along with experiments demonstrating its performance in detecting moisture absorption on uranium oxide, moisture and carbon dioxide absorption on the lithium hydride/hydroxide system, and carbon dioxide absorption on potassium borohydride. 13 figures.
This paper presents a method to evaluate and improve the performance of quantum dot infrared photodetectors (QDIPs). We proposed a device model for QDIPs. The developed model accounts for the self-consistent potential distribution, features of the electron capture and transport in realistic QDIPs in dark and illumination conditions. This model taking the effect of donor charges on the spatial distribution of the electric potential in the QDIP active region. The model is used for the calculation of the dark current, photocurrent and detectivity as a function of the structural parameters such as applied voltage, doping QD density, QD layers, and temperature. It explains strong sensitivity of dark current to the density of QDs and the doping level of the active region. In order to confirm our...
Earth degassing specifically of carbon dioxide CO2 is of increasing interest with respect to the global carbon budget, related climate effects, earthquake and volcano eruption mechanisms, as well as plant physiological reactions in gas-rich environments. Investigations in all of these disciplines require the detection of surface CO2 degassing structures and quantification of their emissions. We introduce minimal thermal change detection based on infrared imaging as a new remote sensing tool for the detection of earth surface thermal anomalies suiting among others to discover earth degassing locations of any origin. The method allows for seamless areal search and monitoring of degassing structures in any terrain. As proof of concept infrared imaging measurements were performed at the Bossol...
The objective of this study was to determine whether walking and running at different treadmill speeds resulted in different metabolic and cardiovascular responses in the vastus lateralis (VL) and lateral gastrocnemius (LG) by examining metabolite accumulation and tissue oxygen saturation. Ten healthy subjects (6 males, 4 females) completed a submaximal treadmill exercise test, beginning at 3.2?km?h?1 and increasing by 1.6?km?h?1 increments every 3?min until reaching 85% of age-predicted maximal heart rate. Muscle tissue oxygenation (SO2), total hemoglobin (HbT) and interstitial hydrogen ion concentration ([H+]) were calculated from near infrared spectra collected from VL and LG. The [H+] threshold for each muscle was determined using a simultaneous bilinear regression. Muscle and treadmil...
Fourier-transform infrared (FTIR) spectroscopy was used to monitor amino acids, organic acids, and changes during ripening. Twelve Cheddar cheese samples were ripened for 73 days and samples were drawn periodically. Water-soluble fractions of samples were analyzed by gas chromatography (20 amino acids), liquid chromatography (three organic acids), and FTIR spectroscopy (4000-700 cm-1). Spectra were correlated with chromatographic data and ripening events and analyzed by multivariate statistics to develop prediction and classification models. Most models showed a good fit (correlation coefficient > or =0.89) and could predict the levels of amino acids and organic acids and age of the cheese in less than 20 min. Lactic acid, leucine, glutamic acid, asparagine, phenylalanine, and valine were ...
In this article, we investigate the "naive non-abelianization" (NNA) contributions of the higher-twist Feynman diagrams to the large-$p_T$ inclusive pion production cross section in proton-proton collisions and present the general formulae for the higher-twist differential cross sections in the case of the running coupling and frozen coupling approaches. We compared the resummed "naive non-abelianization" higher-twist cross sections with the ones obtained in the framework of the frozen coupling approach and leading-twist cross section. The structure of infrared renormalon singularities of the higher twist subprocess cross section and it's resummed expression (the Borel sum) are found. It is shown that the resummed result depends on the choice of the meson wave functions used in the calculations. We discuss the phenomenological consequences of possible higher-twist contributions to the meson production in proton-proton collisions in within NNA at RHIC.
The high-frequency data from 12 sensors at the ITCE 1976 are analyzed to determine the Kolmogoroff constants for velocity, temperature and humidity fluctuations, ..cap alpha../sub u/, ..cap alpha../sub T/, and ..cap alpha../sub q/. The occurrence of aliasing in the spectral analysis in some cases together with the limited response of some sensors at the higher frequencies introduces some uncertainties into the analysis. The Soviet sonic anemometer, fine-wire thermometer and infrared hygrometer and the Australian infrared hygrometer provide the best information, namely that: ..cap alpha../sub u/ = 0.59 +/- 0.01, ..cap alpha../sub T/ = 0.68 +/- 0.02, ..cap alpha../sub q/ = 0.76 +/- 0.03, where the errors quoted refer solely to statistical errors. The other instruments provide general support to these values. The technique of using spectral density measurements to determine eddy fluxes is illustrated.
We report novel, high-angular resolution interferometric measurements that imply the near-infrared nuclear emission in NGC 4151 is unexpectedly compact. We have observed the nucleus of NGC 4151 at 2.2 microns using the two 10-meter Keck telescopes as an interferometer and find a marginally resolved source ~0.1 pc in diameter. Our measurements rule out models in which a majority of the K band nuclear emission is produced on scales larger than this size. The interpretation of our measurement most consistent with other observations is that the emission mainly originates directly in the central accretion disk. This implies that AGN unification models invoking hot, optically thick dust may not be applicable to NGC 4151.
Efficient, low-temperature conversion of infrared light into visible light (red, orange, green) is reported at single heterojunctions and undoped quantum wells of GaAs and ordered Al_xGa_1_-_xInP_2; an increase in photon energy of 700 meV is obtained. The signal originates from the high-band-gap layers and disappears only if the excitation energy is tuned below the GaAs band gap. The intensity of the up-converted photoluminescence (PL) is found to decrease significantly slower with increasing temperature than that of the regular PL and it remains observable up to 200 K. Interface-induced cold Auger processes along with the presence of trapped states for both electrons and holes in these ordered alloys account for this nonlinear mechanism. A colinear double-beam experiment confirms this. copyright 1996 The American Physical Society.
The effect of varying pD(11-13,7) on the reaction of hydrogen with (Co/sup 11/(CN)/sub 5/)/sup 3/- in deuterium oxide has been studied by using infrared spectroscopy to determine the ratio of (Co/sup 111/(CN)/sub 5/X)/sup 3/- (X=H,D) in the solids precipitated from the steady state under hydrogen. The results show that the uptake of hydrogen does not liberate a free proton and that the rate of (Co/sup 111/(CN)/sub 5/H)/sup 3/- -D/sub 2/,0 exchange increases with pD but becomes pD independent at pD 7 greater than 13,5.
The n3 and n4 vibrational transitions of CH3 and CD3 isolated in solid parahydrogen were studied by high-resolution infrared spectroscopy. The radicals were produced by in situ UV photolysis of methyl iodides trapped in solid parahydrogen. The observed spectra showed clear rotational fine structures, which were subjected to further splitting due to the electrostatic field of solid parahydrogen. The molecular constants and crystal field parameters of the radicals in solid parahydrogen were determined by analyzing the spectral structures of the n3 and n4 transitions of CD3 by the crystal field theory. The rotational constants of the CD3 radical were found to be only a few percent smaller than those in the gas phase. The determined crystal field parameters indicated significant quantum effect...
An 80 keV, 3.6 MW neutral beam injection system has recently been installed on Doublet III, and the installation of a second system is scheduled within several months. Armor plate consisting of /approximately equals/100 graphite tiles (10 cm x 10 cm) coated with TiC has been plated over portions of the inner vacuum wall lying in the line of sight of the ion sources. In order to monitor the condition of the armor plate an infrared camera and a set of optical pyrometers have been installed alongside the beamline and view the armor plate through a CaF/sub 2/ window. The pyrometers measure the temperature of the armor plate associated with the maximum of the intensity distribution of each ion source.
In a laser system for converting infrared laser light waves to visible light comprising a source of infrared laser light waves and means of harmoic generation associated therewith for production of light waves at integral multiples of the frequency of the original wave, the improvement of said means of harmonic generation comprising a crystal having the chemical formula X.sub.2 Y(NO.sub.3).sub.5 .multidot.2 nZ.sub.2 o wherein X is selected from the group consisting of Li, Na, K, Rb, Cs, and Tl; Y is selected from the group consisting of Sc, Y, La, Ce, Nd, Pr, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Al, Ga, and In; Z is selected from the group consisting of H and D; and n ranges from 0 to 4.
It is known that the plant cuticle represents the first barrier that must be overcome by any chemical reaching the plant surface from the atmosphere before entering the plant. Because of the importance of the cuticle as a barrier to penetration of a wide variety of compounds, its morphology, chemistry, and permeability have been extensively studied. However, only limited information is available on the nature of functional chemical groups present and their interaction and role during the penetration process. The usefulness of in situ Fourier transform infrared spectroscopy studies in identifying functional groups present in isolated cuticles is described and their relationships to the structure of the cuticular membrane are discussed. Applications of infrared spectroscopy on the presence and role of phenolics in the cuticle structure and during the cuticle development, nitrogen oxide binding to isolated cuticles, and the interactions between ...
Disclosed is a gas-fired cooktop for a range which provides high thermal efficiency and low emissions of air pollutants, particularly low levels of NO{sub x}. The cooktop includes a perforated tile burner which radiates infrared energy upward at a high flux rate to rapidly quench burner gas temperatures and inhibit the formation of NO{sub x}. A perforated glass-ceramic jet plate positioned between the burner and a cooking vessel transmits most of the radiant infrared energy from the burner to the vessel and also forms jets of combustion products which are directed against the bottom of the vessel fo convective heating. Thermal efficiencies of up to about 70% and NO{sub x} emissions as low as about 15ppM are achieved by the cooktop.
The simultaneous hydrogen and silicon atom densities in amorphous silicon, a-Si, films prepared by the glow discharge technique have been measured by 25 MeV #alpha#-particle elastic scattering. Integrated band intensities for the silicon-hydrogen stretching modes, #omega#_1sup(s) and #omega#_2sup(s) in the region 1800 to 2200 cm"-"1 were determined for the same freely supported films. A similar analysis has been carried out for the bands observed at 890, 840 and 640 cm"-_1. Effective oscillator strengths for the #omega#_1sup(s) and #omega#_2sup(s) modes in a-Si films have been estimated and compared with the current theories on the effect of the silicon matrix on the infrared absorption characteristics. (author).
The preliminary design of a far-infrared free-electron laser with a Coaxial Hybrid Iron (CHI) wiggler is presented. The CHI wiggler consists of a central rod and outer ring of alternating ferrite and dielectric spacers. A periodic wiggler field is produced when the CHI structure is immersed in an axial magnetic field. The design under investigation makes use of 1A, 1MV annular electron beam interacting with the TE{sub 01} coaxial waveguide mode at approximately 1 THz ({lambda} = 300 {mu}m). The nominal wiggler period is 0.5 cm and the inner and outer waveguide radii are 0.4 and 0.8 cm, respectively. An axial guide field of 5-10 kG is used. The device performance is modeled with slow-time-scale nonlinear code. Self fields and axial velocity spread are included in the model. Theoretical results will be presented.
In this study, thermoluminescence (TL) dating of archaeological artefacts from Geboltskirchen (Upper Austria) and Haselbach (Lower Austria) has been carried out. To receive a comparison with TL dating, all samples have been investigated additionally by means of infrared-stimulated luminescence (IRSL) analysis. The samples were prepared according to the common fine-grain technique. All important dating parameters such as potassium concentration, thorium/uranium ratio, moisture content, etc. were determined. A methodology for IRSL was developed, describing all steps of the procedure from sample preparation to measurement for any kind of ceramic artefacts. Dating results from TL and IRSL investigations of ancient pottery from Geboltskirchen and Haselbach will be discussed.
The characteristics of infrared-stimulated luminescence (IRSL) from a sample of potassium feldspar at low temperatures are presented. These studies extend the previous work from this laboratory on the optical bleaching characteristics and emission spectra of feldspars at room temperature and recent measurements of the stimulated spectrum for a sample of potassium feldspar at room temperature. Stimulation spectra have been measured at 290, 160 and 145 K. By fitting Gaussian functions to the spectra, the peak position is shown to shift to higher photon energies at lower temperatures and the full-width half-maximum of the peak to reduce with decreasing temperature. The variation of IRSL intensity with temperature for several stimulating wavelengths has been determined and the form of the IRSL decay curve measured at 290 and 160 K. No substantial differences were observed in the form of the decay curves at each temperature. (author).
We have developed efficient spectrally selective infrared (IR) emitters that can be utilized for thermophotovoltaic (TPV) power generation by using stainless steel (SUS304) substrates coated with b- FeSi2 thin films. To develop spectrally selective emitters, we theoretically propose antireflection (AR) coatings consisting of a single layer of a dielectric material having a high refractive index (~5) and are appropriate for use with metals such as stainless steels in the IR region. This type of AR coating is fabricated by sputtering a b- FeSi2 thin film on a polished SUS304 substrate. The reflectance in the IR region is successfully reduced to less than 10%. In addition, the AR properties are stable even at 700 K in air. Therefore, metals with AR coatings of b- FeSi2 can be applied to IR em...
From the COMBO-17 digital sky survey data, 1,231 faint blue galaxies with photometric redshifts of 0.1infrared data. The results indicate that there are 183 galaxies whose photometric redshifts derived from both optical and infrared data are greater than 1.2, that the rms error of the derived photometric redshifts is 0.046, and that to increase the photometric SNR is also helpful for discriminating those misjudged low-redshift galaxies by using only the optical data. We have studied a...
We have investigated the effect of plasma nitriding and plasma nitrocarburizing on the microstructure and properties of electroplated chromium. Plasma nitriding and plasma nitrocarburizing are applied to 15-100 [mu]m thick electroplated hard chromium coatings to increase both the wear and the corrosion resistance. The properties of the plasma-modified hard chromium layers are characterized by measuring the wear resistance with a Taber wear tester and the corrosion resistance with a salt spray fog test. Cyclic voltammetry is performed in a standard electrochemical cell using a 0.5 M H[sub 2]SO[sub 4] solution acidified to pH 0.3. The compound layer after plasma nitriding consists of CrN and Cr[sub 2]N with a maximum hardness of about 1100 HK[sub 0.01]. After plasma nitrocarburizing, Cr[sub 3]C[sub 2] and Cr[sub 7]C[sub 3] are formed. After plasma nitrocarburizing, the maximum hardness is increased up to ...
In the present thesis I discuss the hard spectator interaction amplitude in B {yields} {pi}{pi} at NLO i.e. at O({alpha}{sup 2}{sub s}). This special part of the amplitude, whose LO starts at O({alpha}{sub s}), is defined in the framework of QCD factorization. QCD factorization allows to separate the short- and the long-distance physics in leading power in an expansion in {lambda}{sub QCD}/m{sub b}, where the short-distance physics can be calculated in a perturbative expansion in {alpha}{sub s}. Compared to other parts of the amplitude hard spectator interactions are formally enhanced by the hard collinear scale {radical}({lambda}{sub QCD}m{sub b}), which occurs next to the mb-scale and leads to an enhancement of {alpha}{sub s}. From a technical point of view the main challenges of this calculation are due to the fact that we have to deal with Feynman integrals that come with up to five external legs and with three ...
Over the past 40 years, cavern storage of LPG's, petrochemicals, such as ethylene and propylene, and other petroleum products has increased dramatically. In 1991, the Gas Processors Association (GPA) lists the total U.S. underground storage capacity for LPG's and related products of approximately 519 million barrels (82.5 million cubic meters) in 1,122 separate caverns. Of this total, 70 are hard rock caverns and the remaining 1,052 are caverns in salt deposits. However, along the eastern seaboard of the U.S. and the Pacific northwest, salt deposits are not available and therefore, storage in hard rocks is required. Limited demand and high cost has prevented the construction of hard rock caverns in this country for a number of years. The storage of natural gas in mined caverns may prove technically feasible if the geology of the targeted market area is suitable; and economically feasible if the cost and ...
Sintered glass-ceramics were produced from coal fly ashes, red mud from aluminum production and silica fume. The capabilities of Tuncbilek fly ash and a mixture of Orhaneli fly ash, red mud and silica fume to be vitrified and devitrified by sintering process were investigated by means of scanning electron microscopy and X-ray diffraction analysis. To determine the effect of binder in the sintering technique, glass powders were pressed without or with the addition of polyvinyl alcohol. Owing to microstructural observations, density and hardness measurements, it can be said that physical properties and the hardness of the produced samples strongly depended on the crystallization degree of the samples. Toxicity characteristic leaching procedure test results showed that glass-ceramic samples produced by using sintering technique could be considered as nonhazardous materials. Chemical durability of the sintered glass-ceramic samples was also good. ...
Hard X-ray/gamma-ray spectrometers aboard two interplanetary spacecraft, Ulysses and Pioneer Venus Orbiter (PVO), and two near-Earth spacecraft, Yohkoh and Compton Gamma Ray Observatory (GRO/BATSE), are currently in operation. A unique set of circumstances have permitted the observation of the 15 November 1991 (2238 UT) flare by all the four instruments. This intense flare (GOES class X 1.5) was associated with the bright (3B) H-alpha flare located on the disk (S13, W19) in the active region 6919. At the time of the flare, the Ulysses and PVO spacecraft were located respectively 101[degree] and 52[degree] west of the Sun-Earth line. Thus the view angles for the PVO and Ulysses instruments were quite different from those of the near-Earth instruments on GRO and Yohkoh. The preliminary photon energy spectra observed by the four instruments at different times during the flare will be presented and their implications regarding the directivity of ...
Total-dose irradiation seriously damages MOS devices and their circuit performance. Threshold voltage shifts, transconductance degradation and increase in off-state leakage current are generally observed for irradiated devices. These instabilities are essentially due to positive and/or negative charge trapping in SiO_2 and interface trap generation at the SiO_2/Si interface. Radiation hardening of CMOS VLSIs is to eliminate these trapping effects, and for this purpose, special considerations for fabrication processes and layout design are necessary. In this paper, basic mechanisms for radiation-induced charge trapping and related effects on MOS devices are reviewed. Also discussed are radiation-hardening technologies from both fabrication-process and layout-design viewpoints. Using these technologies, 1 #mu#m radiation-hard CMOS gate arrays have been successfully developed. Experimental data taken for 2k-gate test chips indicate that radiation ...
A systematic study was made on MoSi{sub 2}-based nanolayer coatings. Alternating layers with thickness 1-20 nm were prepared by sputtering. Nitrided MoSi{sub 2} has a very high crystallization temperature, >1000 C, and MoSi{sub 2}Nx (x=3-4) can be used as a stable second phase reinforcement or diffusion barrier coatings. Mechanical properties depend strongly on phase and morphology of the layers: hardness and modulus is significantly increased in the crystallization. The nanolayers have much higher hardness but lower modulus (which project higher toughness in the nanolayers). Wear resistance is improved with decreasing layer thickness. Single phase MoSi{sub 2}Nx (x=0-4.2) has a wide range of hardness and modulus with varying N content and annealing, suggesting the possibility of engineering MoSi{sub 2}Nx to produce different material properties for different mechanical applications. Most of this paper is made up of ...
Direct current (DC) glow discharge plasma nitriding was carried out on three selected surface-roughened AISI 304 stainless steel samples at 833 K under 4 mbar pressures for 24 h in the presence of N{sub 2}:H{sub 2} gas mixtures of 50 : 50 ratios. After plasma nitriding, the phase formation, case depth, surface roughness, and microhardness of a plasma-nitrided layer were evaluated by glancing angle x-ray diffractogram, optical microscope, stylus profilometer, and Vickers microhardness tester techniques. The case depth, surface hardness, and phase formation variations were observed with a variation in initial surface roughness. The diffraction patterns of the plasma-nitrided samples showed the modified intensities of the {alpha} and {gamma} phases along with those of the CrN, Fe{sub 4}N, and Fe{sub 3}N phases. Hardness and case depth variations were observed with a variation in surface roughness. A maximum hardness of 1058 Hv ...
An experimental evaluation of the Fano factor F in silicon at hard X-ray energies (5.9-136.5 keV) has been performed by means of a low-noise, high charge collection efficiency silicon drift detector with on-chip electronics. A dependence of F from the detector temperature as well as from the energy of the X-ray photons has been found. Assuming a pair creation energy equal to 3.64 eV, at +20 deg. C the F factor was observed to vary from 0.124{+-}0.006 at 5.9 keV up to 0.159{+-}0.002 at 122 keV. At -35 deg. C, the change of F with respect to the photon energy was less remarkable but nevertheless statistically significant, from 0.123{+-}0.002 at 5.9 keV up to 0.134{+-}0.001 at 122 keV. To our knowledge, the present results represent the first experimental evidence of an energy dependence of the Fano factor in silicon at hard X-ray energies.
This paper presents the first results on formation and study of structure and properties of micro- and nanocomposite combined coatings. By means of modeling the deposition processes (deposition conditions, current density-discharge, plasma composition and density, voltage) we formed the three-layer nanocomposite coatings of Ti-Al-N/Ti-N/Al_2O_3. The coating composition, structure and properties were studied using physical and nuclear-physical methods. The Rutherford proton and helium ion backscattering, scanning electron microscopy with microanalysis, grazing incidence X-ray diffraction, as well as nanohardness tests (hardness) were used. Measurements of wear resistance and corrosion resistance in NaCl, HCl and H_2SO_4 solutions were also performed. For testing mechanical properties such characteristics of layered structures as hardness H, elastic modulus E: H"3/E"2 etc. were measured. It is demonstrated that the formed three-layer ...
The plastic displacements around Knoop indentations made in hard titanium/aluminum multilayered films on soft aluminum alloy substrates have been studied. Indentations were cross-sectioned and imaged using the focused-ion-beam (FIB) milling and high-resolution scanning electron microscopy (SEM), respectively. The FIB milling method has the advantage of removing material in a localized region without producing mechanical damage to the specimen. The micrographs of the cross-sectioned indentations indicate that most of the plastic deformation around the indentation is dominated by the soft aluminum substrate. There is a very small change in the multilayered film thickness around the indentation{emdash}less than 10{percent}. The plastic deformation of the thin film resembles a membrane being deflected by a localized pressure gradient across the membrane. Stress-induced voids are also observed in the multilayered film, especially in the area around the indentation apex. ...
Al{sub x}Ga{sub 1{minus}x}P layers (0 {le} x {le} 0.7), with thicknesses of {ge}1 {micro}m were grown on Si (100) wafers by metal-organic molecular beam epitaxy (MOMBE) at 450 C. Transmission electron micrographs of the single crystal films revealed that the microstructure contains stacking faults and microtwins especially near the interface as well as both threading and misfit dislocations. Hardness and elastic modulus were measured using a Nanotest 500 indenter, which can probe the film properties without influence from the substrate. The hardness H varies linearly according to (11.8 {minus} 2.3x) GPa. The absence of alloy hardening is due to the fact that there is no difference in atomic size of Al and Ga. The indentation modulus E/(1{minus}v{sup 2}) decreases monotonically from 136 GPa for GaP to 129 GPa for Al{sub 0.7}Ga{sub 0.3}P and bows only slightly (about 2%) below the straight line of linear interpolation.
The effects of key metallurgical variables on the low fluence hardening in a set of A533B model steels were evaluated over a wide range of irradiation temperatures. Above about 163 degrees C hardening increased with higher copper and nickel contents, as is typical of the pressure vessel operating regime around 290 degrees C. However, at 121 degrees C the hardening was generally lower and unaffected by copper and nickel variations. This observation of decreased hardening with lower temperature (e.g. an open-quotes invertedclose quotes temperature dependence) is tentatively attributed to a reduced contribution of copper precipitation. Tensile data for a set of commercial steels with a range of (uncontrolled) compositions also showed minimal sensitivity to copper variations at 121 degrees C. Unlike the hardness data no systematic reductions in the yield stress increases were observed between 163 and 121 degrees C. However, the ultimate tensile strength did decrease at ...
A wear-resistant nitrided layer was formed on a 304L austenitic stainless steel substrate by DC plasma nitriding. Effects of DC plasma nitriding parameters on the structural phases, micro-hardness and dry-sliding wear behavior of the nitrided layer were investigated by optical microscopy, X-ray diffraction, scanning electron microscopy, micro-hardness testing and ring-on-block wear testing. The results show that the highest surface hardness over a case depth of about 10 #mu#m is obtained after nitriding at 460 deg. C. XRD indicated a single expanded austenite phase and a single CrN nitride phase were formed at 350 deg. C and 480 deg. C, respectively. In addition, the S-phase layers formed on the samples provided the best dry-sliding wear resistance under the ring-on-block contact configuration test.
In this work, an attempt was made to develop a novel type of wear-resistant composite employing a TiNi alloy matrix reinforced by hard particles. Titanium carbide was chosen as the reinforcing phase because of its high hardness and TiNi alloy as the matrix due to its pseudoelasticity and good toughness. TiC particles may sustain external load, while the TiNi matrix may accommodate deformation, absorb impact energy and retain the hard particles. Such a combination is expected to lead to an enhanced wear resistance, compared to TiNi alloy. As a matter of fact, some efforts were previously made to develop TiNi-matrix composite reinforced by ceramic particles. However, the emphasis of those studies was put on effects of the reinforcing particles on the phase transformation behavior, shape memory effect and some mechanical properties of the composite; no attempt was made to explore the potential benefit of the material for wear ...
TNF-doped Mylar is a new radiation-hard dielectric that has recently been qualified as a viable substitute for Mylar in capacitors. The advantage of TNF-doped Mylar is that it satisfies both the nuclear safety and radiation hardness requirements of weapons. Mylar is not radiation-hard. Aging and compatibility studies were carried out to insure that (1) TNF does not diffuse from the film during fabrication of the capacitor or during storage; and (2) there are no compatibility problems with aluminum foil (the conductor) or Fluorinert (the secondary dielectric). Losses of TNF were barely detectable during the vacuum bakes used in fabricating capacitors or during accelerated aging tests carried out below T{sub g} (70C) over a two year period in air. In other accelerated tests, no compatibility problems were detected with aluminum or Fluorinert. TNF-doped Mylar is now being used in the MC-4109 capacitor that was called out for ...
The effect of severe plastic deformation by cold high pressure torsion (HPT) on radio frequency (RF) plasma nitriding of pure iron, as well as St2K50 and X5CrNi1810 steels was investigated. Nitriding was carried out for 3 h in a nitrogen atmosphere at a pressure of 10{sup -5} bar and temperatures of 350 and 400 deg. C. Nitrided specimens were analysed by scanning electron microscopy (SEM), X-ray diffraction and micro hardness measurements. It was found that HPT enhances the effect of nitriding leading almost to doubling of the thickness of the nitrided layer for pure iron and the high alloyed steel. The largest increase in hardness was observed when HPT was combined with RF plasma nitriding at 350 deg. C. In the case of pure iron, the X-ray diffraction spectra showed the formation of {epsilon} and {gamma}' nitrides in the compound layer, with a preferential formation of {gamma}' at the expense of the {alpha}-phase at the ...
Thin films of new metastable materials from the system Ti-B-C-N were deposited on metallic substrates by d.c. magnetron sputtering in different Ar+N{sub 2} atmospheres. The multiphase compound targets used were based on various compositions on the TiC-TiB{sub 2} and TiB{sub 2}-C tie lines of the Ti-B-C phase diagram. The structure and chemical composition of the films were characterized by electron microprobe analysis, depth profiling Auger electron spectroscopy, X-ray diffraction and transmission electron microscopy. The hardness, critical load of failure and the tribological behavior of the coatings were investigated. Superhard single-phase crystalline metastable Ti-B-C-N layers with hardness values exceeding 5000 HV{sub 0.05} and extremely low sliding wear against 100Cr6 and Al{sub 2}O{sub 3} counterparts could be produced by reactive sputtering of various TiC-TiB{sub 2} targets in Ar+N{sub 2} atmospheres with low nitrogen flows. In the case ...
The influences of temperature and duration of tempering on hardness and microstructure were investigated at high-temperature martensitic and low-carbon steels with 9% chrome and the further alloying elements molybdenium, vanadium, niobium and partially tungsten. After austenitizing and subsequent air cooling the steels were tempered at temperatures below, at and above Ac{sub 1b} for different times and finally a hardness test was performed. Making use of the temperature dependence of the hardness tempering diagrams were constructed and the Hollomon-Jaffe-Parameter on the three steels was determined within its application limits. Micrographs of the structure shows the formation of the carbides and the martensite. At tempering temperatures below Ac{sub 1b} a decrease of hardness occurs, above Ac{sub 1b}, a hardness rise due to the partial austenitizing was obtained. While hardening ...
Full text of publication follows: Radiation hardening and embrittlement due to high-energy neutron radiation around 623 K are the important issues on reduced-activation ferritic/martensitic (RAF/M) steels. It is expected that the improvement of radiation hardening might be one of effective ways to control the mechanical properties of RAF/M after irradiation. It has been reported that the weld joint has less hardening than the base metal from the tensile test results of TIG weldments irradiated in HFIR. This report indicated that radiation hardening can be reduced by the optimization of heat treatment condition for F82H. The purposes of this study are to establish the condition of heat treatment for minimum of radiation hardening in F82H steel using Neutron/Ion-irradiation and to examine a correlation between tensile property and micro-hardness before/after irradiation. The materials used in this study were F82H IEA heat and F82H heat treatment variants. Neutron ...
W. E. B. Du Bois, one of the brightest lights in African American history, wrote a sparkling critique of the American social and economic system originally planned as part of the Bronze Booklets series, edited and published by Alain Locke and the Associates in Negro Folk Education. The piece was never published and has, until now, been lost to the annals of adult education history. Using historical evidence, the authors examine Du Bois's Basic American Negro Creed and the circumstances that led to its exclusion from the series. It is argued that the Creed was far too radical for the liberal minded Carnegie Corporation and its leaders who were only interested in accommodating adult education for Blacks through the AAAE funded Bronze Booklets. The exclusion of the Creed represents an example of repressive tolerance by the AAAE.
The microbial process of converting organic matter into methane and carbon dioxide is so complex that anaerobic digesters have long been treated as {open_quotes}black boxes.{close_quotes} Research into this process during the past few decades has gradually unraveled this complexity, but many questions remain. The major biochemical reactions for forming methane by methanogens are largely understood, and evolutionary studies indicate that these microbes are as different from bacteria as they are from plants and animals. In anaerobic digesters, methanogens are at the terminus of a metabolic web, in which the reactions of myriads of other microbes produce a very limited range of compounds - mainly acetate, hydrogen, and formate - on which the methanogens grow and from which they form methane. {open_quotes}Interspecies hydrogen-transfer{close_quotes} and {open_quotes}interspecies formate-transfer{close_quotes} are major mechanisms by which methanogens obtain their ...
The retention indices of cycloalkenes and cycloalkadienes with C/sub 6/-C/sub 13/ rings are determined by gas-liquid chromatography (GLC) on glass capillary columns coated with OV-1 and Ucon LB 550X and by gas-solid chromatrography (GSC) on a microcolumn packed with uncoated graphitized thermal carbon black (GTCB). Structure-retention correlations are derived on using index differences such as H/sup OV/, H/sup GTCB/ and ..delta..I values, considering the differences in the stereochemistry of these compounds. It is shown that the combined application of index increments obtained in GLC and GSC provides more detaled structure informations. The value of the retention index units agree with the most stable conformations of the alicyclic compounds. The high value for the energy equivalent to an index unit (..delta..G/sub I.U./ = 4.18 kJ/mol) confirms that graphitized thermal carbon black causes much stronger dispersive interactions than any nonpolar ...
Both x-ray and optical cone-beam CT (CBCT) scanners are limited by scattered photons that contaminate the primary images. Transparent radiochromic gels and plastics are anticipated to produce less scattering than polymerization gels and hence result in reconstructed dose distributions with greater contrast and dynamic range. Four methods of scatter measurement were investigated to quantify scatter fractions using an in-house optical CBCT scanner. The methods consisted of generating either 'coin' shadows or primary beamlets in transmission images. The four methods generated similar results of 10% scatter fractions in gel transmission images for this particular scanner configuration with both leuco crystal violet and carbon black micelle gels. The scatter contributions were distributed as 5% from micelle gel, 2% from Teflon wall, 2% from refractive index matching liquid and 1% other sources. Applying a uniform background subtraction of 2% of open ...
We study the Sunyaev-Zel'dovich (SZ) effect potentially generated by relativistic electrons injected from dark matter (DM) annihilation or decay in the Galaxy, and check whether it could be observed by Planck or ALMA, or even imprint the current CMB data as e.g. the specific fluctuation excess claimed from an recent re-analysis of the WMAP-5 data. We focus on high-latitude regions to avoid contamination of the Galactic astrophysical electron foreground, and consider the annihilation or decay coming from the smooth DM halo as well as from subhalos, further extending our analysis to a generic modeling of spikes arising around intermediate-mass-black-holes (IMBHs). We show that all these dark Galactic components are unlikely to produce any observable SZ effect. For a self-annihilating DM particle of 10 GeV with canonical properties, the largest optical depth we find is $\\tau_e \\lesssim 10^{-7}$ for massive isolated subhalos hosting IMBHs. We conclude that dark ...
We review results from general relativistic axisymmetric magnetohydrodynamic simulations of accretion in Sgr A*. We use general relativistic radiative transfer methods and to produce a broad band (from millimeter to gamma-rays) spectrum. Using a ray tracing scheme we also model images of Sgr A* and compare the size of image to the VLBI observations at 230 GHz. We perform a parameter survey and study radiative properties of the flow models for various black hole spins, ion to electron temperature ratios, and inclinations. We scale our models to reconstruct the flux and the spectral slope around 230 GHz. The combination of Monte Carlo spectral energy distribution calculations and 230 GHz image modeling constrains the parameter space of the numerical models. Our models suggest rather high black hole spin ($a_*\\approx 0.9$), electron temperatures close to the ion temperature ($T_i/T_e \\sim 3$) and high inclination angles ($i \\approx 90 \\deg$).
If the first (PopIII) stars were very massive, their final fate is to collapse into very massive black holes. Once a proto-black hole has formed into the stellar core, accretion continues through a disk. It is widely accepted, although not confirmed, that magnetic fields drive an energetic jet which produces a burst of TeV neutrinos by photon-meson interaction, and eventually breaks out of the stellar envelope appearing as a Gamma Ray Burst (GRB). Based on recent numerical simulations and neutrino emission models, we predict the expected neutrino diffuse flux from these PopIII GRBs and compare it with the capabilities of present and planned detectors as AMANDA and IceCube. If beamed into 1% of the sky, we find that the rate of PopIII GRBs is $\\le 4 \\times 10^6$ yr$^{-1}$. High energy neutrinos from PopIII GRBs could dominate the overall flux in two energy bands [$10^4 - 10^5$] GeV and [$10^5 - 10^6$] GeV of neutrino telescopes. The enhanced ...
In this paper, we investigate the effect of the solid surface on the fluid-fluid intermolecular potential energy. This modified fluid-fluid interaction energy due to the inducement of a solid surface is used in the grand canonical Monte Carlo (GCMC) simulation of various noble gases, nitrogen, and methane on graphitized thermal carbon black. This effect is such that the effective interaction potential energy between two particles close to surface is less than the potential energy if the solid substrate is not present. With this modification the GCMC simulation results agree extremely well with the experimental data over a wide range of pressures while the simulation results with the unmodified potential energy give rise to a shoulder near the neighborhood of monolayer coverage and the significant overprediction of the second and higher layer coverages. In particular the unmodified GCMC results exhibit very sharp change in those higher layers while the experimental ...
Assessment of the oil shale resources in Kentucky has continued with 75 NX cores available where the oil shale crops out or is overlain by relatively thin cover in the area from Estill County westward to Bullitt County. In this 14 county area, the total black shale section thins across the crest of the Cincinnati arch and changes stratigraphically from that characteristic of the Ohio Shale in Estill County to that of the New Albany Shale in Bullitt County. Despite this stratigraphic transition the two high-carbon zones (greater than 8.0% carbon) can be traced across the arch. As the traverse is followed from the east, the intervening low-carbon zones thin such that at the crest of the arch, there are areas where the entire section of black shale contains more than 8% carbon. Then upon leaving the crest the two high-carbon zones separate again with one remaining at the very top of the section and one in the lower part. In the 14 county area, ...
Forty synthetic food colors were determined in drinks and candies by reversed-phase high-performance liquid chromatography with photodiode array detection. The following food colors were analyzed within 19min using a short analytical column (50mmx4.6mm i.d., 1.8mm) at 50degreeC with gradient elution: Ponceau 6R, Tartrazine, Fast yellow AB, Amaranth, Indigotine, Naphthol yellow S, Chrysoine, Ponceau 4R, Sunset yellow FCF, Red 10B, Orange G, Acid violet 7, Brilliant black PN, Allura red AC, Yellow 2G, Red 2G, Uranine, Fast red E, Green S, Ponceau 2R, Azorubine, Orange I, Quinoline yellow, Martius yellow, Ponceau SX, Ponceau 3R, Fast green FCF, Eosine, Brilliant blue FCF, Orange II, Orange RN, Acid blue 1, Erythrosine, Amido black 10B, Acid red 52, Patent blue V, Acid green 9, Phloxine B, Ben...
In many experiments involving fast neutrons generated in nuclear reactions initiated by accelerator produced charged particle beams, it is important to be able to determine accurately the neutron yield from the target. A detector suitable for such applications should have: a constant efficiency over a large energy range; a fast time response; and the ability to discriminate between gamma rays and neutrons. The authors have constructed a open-quotes black neutron detectorclose quotes based on the design of Poenitz that has these characteristics. At the Lowell Van de Graaff accelerator laboratory neutrons are produced via the "7Li(p,n)"7Be reaction using a pulsed proton beam which impinges on metallic lithium targets. The pulsed beam enables the detector to be used in a time-of-flight spectrometer. Use of BC501 liquid scintillator permits neutron-gamma discrimination. The scintillator is viewed by five RCA 48796 photo tubes. The detector is housed in a massive shield ...
This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen and carbon black (CB) as a high-value nano-material with the bonus of zero CO2 emission. The work focused on the development of a medium-scale solar reactor (10kW) based on the indirect heating concept. The solar reactor is composed of a cubic cavity receiver (20cm-side), which absorbs concentrated solar irradiation through a quartz window by a 9cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results in the temperature range 1740-2070K are presented: acetylene (C2H2) was the most important by-product with a mole fraction of up to about 7%, depending on the gas residence time. C2H2 content i...
In the framework of the European Fusion Technology Programme ECN participates in a NET task PSM-8 `Coatings and Surface Effects on Stainless Steel 316L`. High emissivity coatings were developed for enhanced heat transfer from graphite tiles to a Stainless Steel First Wall. Four candidate materials, Cr{sub 2}O{sub 3}, Black Cr, Al{sub 2}O{sub 3}/TiO{sub 2} and TiC were tested as candidate high emissivity coatings. These coatings were manufactured by atmospheric and vacuum plasma spraying technique and the Black Chromium coatings were manufactured by a galvanic coating technique. The tests included total emissivity measurements and Low Cycle Fatigue (LCF) experiments. The total emissivity of two TiC coatings at 525 K appeared to be 0.62 and 0.64. The total emissivity of the TiC and 5 wt% TiO{sub 2}/Al{sub 2}O{sub 3} coating was about 0.7. (orig.)
The massive stars in the Galactic center inner arcsecond share analogous properties with the so-called Hot Jupiters. Most of these young stars have highly eccentric orbits, and were probably not formed in-situ. It has been proposed that these stars acquired their current orbits from the tidal disruption of compact massive binaries scattered toward the proximity of the central supermassive black hole. Assuming a binary star formed in a thin gaseous disk beyond 0.1 pc from the central object, we investigate the relevance of disk-satellite interactions to harden the binding energy of the binary, and to drive its inward migration. A massive, equal-mass binary star is found to become more tightly wound as it migrates inwards toward the central black hole. The migration timescale is very similar to that of a single-star satellite of the same mass. The binary's hardening is caused by the formation of spiral tails lagging the stars inside the binary's ...
This report presents the results of Run 260 performed at the Advanced Coal Liquefaction R&D Facility in Wilsonville. The run was started on July 17, 1990 and continued until November 14, 1990, operating in the Close-Coupled Integrated Two-Stage Liquefaction mode processing Black Thunder mine subbituminous coal (Wyodak-Anderson seam from Wyoming Powder River Basin). Both thermal/catalytic and catalytic/thermal tests were performed to determine the methods for reducing solids buildup in a subbituminous coal operation, and to improve product yields. A new, smaller interstage separator was tested to reduce solids buildup by increasing the slurry space velocity in the separator. In order to obtain improved coal and resid conversions (compared to Run 258) full-volume thermal reactor and 3/4-volume catalytic reactor were used. Shell 324 catalyst, 1/16 in. cylindrical extrudate, at a replacement rate of 3 lb/ton of MF coal was used in the catalytic stage. Iron oxide ...
In this paper we consider the adsorption of argon on the surface of graphitized thermal carbon black and in slit pores at temperatures ranging from subcritical to supercritical conditions by the method of grand canonical Monte Carlo simulation. Attention is paid to the variation of the adsorbed density when the temperature crosses the critical point. The behavior of the adsorbed density versus pressure (bulk density) shows interesting behavior at temperatures in the vicinity of and those above the critical point and also at extremely high pressures. Isotherms at temperatures greater than the critical temperature exhibit a clear maximum, and near the critical temperature this maximum is a very sharp spike. Under the supercritical conditions and very high pressure the excess of adsorbed density decreases towards zero value for a graphite surface, while for slit pores negative excess density is possible at extremely high pressures. For imperfect pores (defined as ...
We present new results from accurate and fully general-relativistic simulations of the coalescence of unmagnetized binary neutron stars with various mass ratios. The evolution of the stars is followed through the inspiral phase, the merger and prompt collapse to a black hole, up until the appearance of a thick accretion disk, which is studied as it enters and remains in a regime of quasi-steady accretion. Although a simple ideal-fluid equation of state with \\Gamma=2 is used, this work presents a systematic study within a fully general relativistic framework of the properties of the resulting black-hole--torus system produced by the merger of unequal-mass binaries. More specifically, we show that: (1) The mass of the torus increases considerably with the mass asymmetry and equal-mass binaries do not produce significant tori if they have a total baryonic mass M_tot >~ 3.7 M_sun; (2) Tori with masses M_tor ~ 0.2 M_sun are measured for binaries ...
Accretion processes in quasars and active galactic nuclei are still poorly understood, especially as far as the connection between observed spectral properties and physical parameters is concerned. Quasars show an additional degree of complexity compared to stars that is related to anisotropic emission/obscuration influencing the observed properties in most spectral ranges. This complicating factor has hampered efforts to define the equivalent of an Hertzsprung-Russel diagram for quasars. Even if it has recently become possible to estimate black hole mass and Eddington ratio for sources using optical and UV broad emission lines, the results are still plagued by large uncertainties. Nevertheless, robust trends are emerging from multivariate analysis of large spectral datasets of quasars. A firm observational basis is being laid out by accurate measurements of broad emission line properties especially when the source rest-frame is known. We consider the most widely ...
Radiation induced polymerization of methylmethacrylate and copolymerization of styrene-acrylonitrile mixture in mamrase Carpinus betulus was carried out by means of #gamma#-ray, under different moisture levels and additives. Under all conditions the degree of polymerization was as high as 60%. No pronounced differences were observed in the kinetics of the polymerization of MMA either with moisture content of wood nor with kind and amount of additives. At high moisture (80% RH) content the dimensional stability of wood-PMMA was increased four fold as compared with untreated wood. The hardness increased about 100% for a weight conversion of monomer of about 30 to 40%. Hardness of this wood-polymer composite is comparable to that of the best noble woods in the world. (author).
In a forthcoming paper we describe a new approach to rapidity gap survival (RGS) in the production of high-mass systems (H = dijet, Higgs, etc.) in exclusive double-gap diffractive pp scattering, pp -> p + H + p. It is based on the idea that hard and soft interactions are approximately independent (QCD factorization), and allows us to calculate the RGS probability in a model-independent way in terms of the gluon generalized parton distributions (GPDs) in the colliding protons and the pp elastic scattering amplitude. Here we focus on the transverse momentum dependence of the cross section. By measuring the ''diffraction pattern'', one can perform detailed tests of the interplay of hard and soft interactions, and even extract information about the gluon GPD in the proton from the data.
The NACE MR-01-75 standard imposes a restriction of 22HRC maximum for regions of a pipeline girth weld that are not in direct contact with H[sub 2]S containing environments. TWI have demonstrated in an earlier project for the Pipeline Research Committee (PRC) that it may be permissible to relax this maximum hardness requirement. Such a relaxation, which already exists in the BS4515: 1984 standard, offers potential benefits when applied to the capping pass and heat affected zone of a pipeline girth weld. This report presents additional data to supplement that obtained in a previous PRC project conducted at TWI. Further pipe materials with differing pipe wall thicknesses have been welded, exposed to an internal H[sub 2]S containing environment and examined for sulphide stress corrosion cracking.
A series of nine model ferritic alloys were ion irradiated at #propor to#300 C using 2.5 MeV He ions to a dose of 1.4 x 10"2"1 ion/m"2, which corresponds to #propor to#0.1 dpa at a depth of 2 #mu#m and #propor to#3.5 dpa at the peak damage region which occurs at about 4 #mu#m deep. The resultant changes in hardness as a function of depth were measured using a Nanoindenter "t"r"a"d"e"m"a"r"k. TEM was used to investigate the defect distributions. The effect of various solutes, Cu and N in particular, but Mn and Ti as well, on the change of hardness and the defect distribution due to the ion irradiation are discussed. (orig.).
The corrosion behavior of hard metals with VC and Cr3C2 grain growth inhibitors was investigated in alkaline solutions by electrochemical methods. The two inhibitors have opposite effects on the corrosion behavior: Cr3C2 significantly improves the corrosion behavior, whereas VC-containing alloys show a poor resistance. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and analytical transmission electron microscopy (TEM) analyses of the distributions of Cr and V in the composite material, as well as in the surface layers formed during corrosion were employed to clarify the influence of these elements on the corrosion behavior. The measurements showed that VC is precipitated mostly along the WC/binder interface after the liquid-phase sintering process, while Cr3C2 is almost homogene...
The X-ray storage phosphor CsBr:Eu2+ in form of needle image plates is believed to be a promising alternative to the granular BaFBr:Eu2+ with regard to PSL yield and spatial resolution. Unfortunately, CsBr:Eu2+ exhibits poor radiation hardness, which is caused by a migration of europium ions initiated by naturally existing defect centers like (Eu2+-VCs)-centers and X-ray generated MEu-centers. It will be shown that the formation of (Eu2+-O2?)-dipoles at the expense of (Eu2+-VCs)-dipoles, incorporated by thermal annealing in O2-containing and humid atmosphere, does not improve the radiation stability. There is, however, a strong improvement in the radiation hardness by codoping of CsBr:Eu2+ with lithium ions, which is accompanied by a complete suppression of the previously observed MEu-cent...
Rossi X-ray Timing Explorer (RXTE) observations of the bright supernova remnant Cas A have revealed a hard power law component above 10 keV in addition to two thermal components inferred from ASCA measurements of the many line centroids from low-Z elements. The power law can be shown to be consistent with synchrotron emission from radio to hard x-rays by electrons of up to 4 x 10"1"3 eV. Measurement of the 1157 keV line by CGRO from "4"4Sc in the chain of decay of "4"4Ti predicts that the two "4"4Ti lines at 68 and 78 keV should appear at the CGRO intensity. RXTE has placed upper limits on such lines that are marginally consistent with the CGRO measurement. Implications of these results on sites for cosmic ray acceleration and nucleosynthesis are discussed.
To clarify the mechanism of plasma nitriding, the authors examined the optical microstructure, the hardness, the precipitation, and the concentration of dissolved nitrogen in Fe-18Cr-9Ni nitrided using plasma in the range of 723-823 K. Compared with ammonia-gas nitriding, the features of plasma nitriding are the formation of small chromium-nitride precipitates (CrN), the absence of an externally nitrided layer, the high concentration of dissolved nitrogen, and the high hardness (HV = 1,200). The diffusion coefficient of nitrogen in the present alloy was determined using the growth rate of the internally nitrided layer, based on calculations used in internal oxidation. Plasma- and gas-nitriding were also compared with respect to the growth rate of the nitrided layer.
In the present investigation, the properties of plasma nitrided AISI 304 steel were studied by changing the presence of nitrogen in the gas mixture. The plasma nitriding was performed at temperature -560 deg C, pressure -4 mbar and duration 24 hours. The nitrided samples were characterized by evaluating the phase composition, micro hardness, and diffusion layer thickness. The phase analysis indicates the mixed phases of CrN and Fe_3N, Fe_3N and Fe_4N which has the highest intensity. The results show the glow discharge plasma nitriding in presence of N_2 (80 vol. %) and H_2 (rest) produced higher hardness as well as higher case depth. (author)
A polymer-based additive that permanently reduces hardness in wood electrical transmission poles treated with a chromated copper arsenate (CCA) preservative, has been developed by a team of IREQ researchers. A three-phase project is being funded by Hydro-Quebec to evaluate the additive's effect on full-size hydro poles subjected to actual climatic conditions. The evaluation project is designed to test the CCA and the additive's degree of retention by analyzing the hardness measurements against climbing tests, and the washing resistance of the chromium, copper and arsenate in the CCA/polymer-additive treatment. CCA-treated poles will be used for reference. Accelerated aging tests to characterize the polymer's resistance to UV rays will also be part of the validation program.
With the aim of optimizing the nitriding process, experimental studies of the plasma nitriding of four selected steels were carried out, using a d.c. glow discharge. The process parameters were varied systematically. By means of transmission and scanning electron microscopy and X-ray diffraction, the microstructures, including the thicknesses of the compound zones and the diffusion zones of the nitrided steels, were obtained. Using cross-sectional samples and a micro-Vickers indenter, hardness depth profiles were also obtained. From the time and temperature dependences of the hardness profiles, effective diffusion constants and corresponding activation enthalpies were obtained. Furthermore, in an attempt to shed some light on the atomistic nitriding mechanisms, the glow discharges were studied by measuring energy spectra of the energetic ions hitting the cathode (the steel test specimens). It was shown that an increase of the mean energy of the ...
Modifications of the structure and mechanical properties in LiF crystals irradiated with MeV-energy Au ions have been studied using nanoindentation, atomic force microscopy and optical spectroscopy. The nanostructuring of crystals under a high-fluence irradiation (above 1013 ions/cm2)?was?observed. Nanoindentation tests show a strong ion-induced increase of hardness (up?to 150?200%), which is related to the high volume concentration of complex color centers, defect aggregates, dislocation loops and grain boundaries acting as strong barriers for dislocations. From the?depth profiling of the hardness and energy loss it follows that both nuclear and electronic stopping mechanisms of MeV Au ions contribute to the creation of damage and hardening. Whereas the electronic stopping is dominating i...
Given the important role of parent-youth communication in adolescent well-being and quality of life, we sought to examine the relationship between specific communication variables and youth perceived quality of life in general and as a deaf or hard-of-hearing (DHH) individual. A convenience sample of 230 youth (mean age = 14.1, standard deviation = 2.2; 24% used sign only, 40% speech only, and 36% sign + speech) was surveyed on communication-related issues, generic and DHH-specific quality of life, and depression symptoms. Higher youth perception of their ability to understand parents' communication was significantly correlated with perceived quality of life as well as lower reported depressive symptoms and lower perceived stigma. Youth who use speech as their single mode of communication ...
A Y-Mg-Si-Al-O-N glass was submitted to swift heavy-ion bombardment at GANIL (Caen, France) and the influence of irradiation on the mechanical properties was studied. The mechanical properties of the glass were characterized both before and after irradiation. Changes in hardness, elastic modulus and fracture toughness of the near-surface irradiated layer were determined using indentation techniques. SRIM calculations allowed to estimate the ions penetration range and the energy deposition relative to electronic and nuclear interactions, which can be correlated to the experimental damaged depth. Meyer's hardness and Young's modulus decrease by about 30 %, while fracture toughness is increased by more than 40 %. (authors)
Magnetic properties of Fe-Co-Mo-Cu-B alloy system with Co up to 26at.% were investigated. After proper thermal treatment, the nanocrystalline grain remains tiny, the density hardly increases, but the room-temperature saturation attains 1.5T mainly due to a high enough Curie temperature. The generally observed slant hysteresis loops point to ribbon surfaces, which stress the ribbon interior and induce a specific magnetoelastic contribution to hard-ribbon-axis magnetic anisotropy even after vacuum annealing. The effect does not come from cobalt but rather from the lack of silicon. Partial removal of the surfaces resulted in a decrease of the loop tilt.
The effect of various hydrogen concentrations on the crystal lattice period and the hardness of titanium alloy was examined, the alloy containing about 16 at.% Mo (27.5 wt. % Mo) and having #beta# structure. The peculiar features of the mechanism of plastic deformation of the alloy were studied after adding hydrogen to it. A dependence of the crystal lattice period on the concentration of hydrogen was obtained for TixMoxH_2 alloy. It has been established that the hardness of the Ti-Mo alloy does not change when hydrogen is added to it. The presence of hydrogen introduces changes into the mechanism of deformation of #beta#-titanium alloy. The configuration of the inverse pole figures after rolling proves that the transverse slip process in an alloy with hydrogen is hampered, and that the coplanar slip process is developing in it.
A test bench was designed and assembled to carry out impact tests on samples and components. The system allows simple and rapid adjustment of the test parameters, such as the shot size and air pressure, with good repeatability of the results. Tests on steel and light alloys were carried out under both as-produced condition and on thin hard-coated samples. Significant reductions in dimple dimensions were seen after coating. FE models simulating the experiments overestimated the dimple depths, although the parameter trend was satisfactorily captured. The residual stresses from coating and shot peening determined numerically are believed to have been proven effective against fatigue.
Ochratoxin A (OTA) was analyzed from 44 liquorice confectionery samples using immunoaffinity cleanup and liquid chromatography coupled with fluorescence detection. The presence of OTA was confirmed by methyl-ester derivatization. Liquorice confectionery samples were purchased from different retail outlets and supermarkets in Spain during 2007-2008, 16 of hard candies and 28 of soft candies. The incidence of OTA varied between 75% and 39% and mean ranged from 2.96 to 0.34mg/kg for hard and soft candies, respectively. Assuming a total mean value of 1.29mgOTA/kg sweet and a consumption of about 1.2g liquorice sweets per day, an OTA weekly uptake of 11ng was obtained, or, based on a total body weight of 30kg for a child consuming these sweets regularly, a weekly intake of 0.37ng/kg body weight...
Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150degreeC, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Youngs modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Youngs modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the i...
AISI 5140 steel was plasma nitrided at various gas mixtures of nitrogen, hydrogen, and argon to investigate the actions of hydrogen and argon on plasma nitriding. The structural and mechanical properties of ion-nitrided AISI 5140 steel have been assessed by evaluating composition of phases, surface hardness, compound layer thickness, and case depth by using X-ray diffraction (XRD), microhardness tests, and scanning electron microscopy (SEM). It was found that the growth of compound layer can be controlled and the diffusion improved when the gas mixture includes H_2 gas. Additionally, it was determined that the amount of Ar in dual gas mixture must be at 20% minimum to obtain distinctive surface hardness and compound layer thickness.
In this work AISI 1045 steel were duplex treated via plasma nitriding of chromized layer. Samples were pack chromized by using a powder mixture consisting of ferrochromium, ammonium chloride and alumina at 1273K for 5h. The samples were then plasma-nitrided for 5h at 803K and 823K, in a gas mixture of 75%N2+25%H2. The treated specimens were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis and Vickers micro-hardness test. The thickness of chromized layer before nitriding was about 8mm and it was increased after plasma nitriding. According to XRD analysis, the chromized layer was composed of chromium and iron carbides. Plasma nitriding of chromized layer resulted in the formation of chromium and iron nitrides and carbides. The hardness of the duplex layer...
The energy, angular momentum, and distance (measured from the center of mass of the nucleus) distributions of the effective number of 6q-fluctons are investigated and it is shown that many of the characteristics of these distributions are universal, i.e., independent of the flucton size. ''Saturation'' of the flucton density in nuclei with mass A approx > 80 and certain other features that determine the difference between the behaviors of the effective numbers of fluctons and deuterons are reported. This is used to explain the well known underestimation (by a factor of 1.5--6) of the cross section for the hard inclusive (p, p'd) process on nuclei calculated in the quasielastic formalism. See S. G. Kadmenskii and V. I. Furman, Alpha decay and elated nuclear reactions (in Russian), Energoatomizdat, Moscow, 1985.
The energy, angular momentum, and distance (measured from the center of mass of the nucleus) distributions of the effective number of 6/ital q/-fluctons are investigated and it is shown that many of the characteristics of these distributions are universal, i.e., independent of the flucton size. ''Saturation'' of the flucton density in nuclei with mass /ital A//approx gt/80 and certain other features that determine the difference between the behaviors of the effective numbers of fluctons and deuterons are reported. This is used to explain the well known underestimation (by a factor of 1.5--6) of the cross section for the hard inclusive (/ital p/, /ital p/'/ital d/) process on nuclei calculated in the quasielastic formalism. See S. G. Kadmenskii and V. I. Furman, /ital Alpha/ /ital decay/ /ital and elated/ /ital nuclear/ /reactions/ (in Russian), Energoatomizdat, Moscow, 1985.
Microstructural observations of damage around indentations in Ti{sub 3}SiC{sub 2} are presented. The Vickers hardness decreased with increasing load and asymptotically approached 4 GPa at the highest loads. No indentation cracks were observed even at loads as high as 300 N. Preliminary strength versus indentation plots indicate that, at least for the large-grained material ({approx}100 {micro}m) studied here, Ti{sub 3}SiC{sub 2} is a damage-tolerant material able to contain the extent of microdamage to a small area around the indent. The following multiple energy-absorbing mechanisms have been identified from scanning electron micrographs of areas in the vicinity of the indentation: diffuse microcracking, delamination, crack deflection, grain push-out, grain pull-out, and the buckling of individual grains.
Silicon sensors have about ten times improved radiation hardness around 130 K temperature, compared with the state-of-art sensors close to room temperature. This is based on the Lazarus effect studied by the RD39 Collaboration of CERN. Other benefits of low temperatures will also be discussed. We shall describe the conceptual design of low-mass detector modules cooled using two-phase flow of argon in miniature cooling pipes integrated in the module structure between the sensors and the readout hybrid circuit. The main engineering features of the cooling system and mechanical support structures are discussed, as well as the benefits arising from the operation of the tracker under cryogenic vacuum. 4 Refs.
The combined processes of plasma nitriding and cathodic arc deposition of (Ti,Cr,Nb)CN coatings were applied to HSS substrates. The nitrided layers, obtained in a mixture of H2 (70%) and N2 (30%) at two different temperatures (480^oC and 510^oC), were examined for the microhardness depth profiles. Characterization of the duplex coatings was performed by investigating elemental and phase composition, texture, hardness, friction and wear. XRD and XPS analyses revealed the formation of a mixture of a carbonitride fcc solid solution, in a dominant proportion, and metallic chromium. The film hardness was measured to be ~34GPa. The duplex (Ti,Cr,Nb)CN coatings exhibited superior tribological behavior as compared to both nitrided layers and non-duplex coatings.
Carbon fibre composite (CFC) was irradiated by hot plasma streams at plasma gun facility MK-200UG. The CFC targets were tested by plasma loads relevant to Edge Localized Modes (ELM) and mitigated disruptions in ITER. Onset condition of CFC evaporation and properties of evaporated carbon were studied by use of infrared pyrometry and visible spectroscopy.
Fourier transform infrared spectroscopy is a simple, fast, reliable and nondestructive analytical method. By using the method developed in Clark Atlanta University, consistent and reliable infrared spectral results can be obtained. An accurate radiant energy can be calculated from these infrared spectra by using a blackbody as the calibration standards. By means of the specially-designed-and-lab-made sampling inlet and the Horiba gas analyzers, the compositions of CO{sub 2}, CO, UCH, NOx and O{sub 2} etc. from the combustion exhaust gases have been on-line accurately analyzed. The commercial natural gas IR burner performed differently in the different conditions. For the methane-air combustion, at the equivalence ratio {Phi} = 1, the IR burner produced its maximum radiation efficiency, {approximately}31.4%, and the concentration of CO{sub 2} reached its maximum value, {approximately}10.7%. In the fuel-lean region, the O{sub ...
The fluorescence, absorption, infrared and Raman spectra of Sm_3Ga_5O_1_2 have been investigated. The energy-level schemes in the energy range 3000-16000 cm"-"1 have been determined. The number and symmetries of the Sm_3Ga_5O_1_2 crystal normal mode have been obtained by the molecular site group analysis and their comparison with the experiment has been made.
In this Brief Report, we analyze a generalized theory of massless scalar QED{sub 2} and show that, unlike the conventional scalar QED{sub 2}, it is free from infrared divergence problems. The model is exactly soluble and may describe, in a (1+1)-dimensional space-time, noninteracting spin-one tachyons. {copyright} {ital 1999} {ital The American Physical Society}
Computer simulations and experiments indicate that we can shape the infrared picosecond pulses of the Mark III FEL in amplitude, frequency, and phase. Strongly modulated fundamental and second harmonic pulses have been generated by operating the Mark III FEL in the regime of strong sideband growth. In this paper, we present the results of simulations and experiments for second harmonic generation with fundamental inputs from 2 to 3 {mu}m.
Research and development activities are reported on absorption spectroscopy, calorimetry, electrolysis, emission spectroscopy, fluorimetry gas chromatography, infrared spectroscopy, liquid chromatography, liquid scintillation counting, mass spectroscopy, microscopy, radiometric analysis, and thermal analysis. A group of miscellaneous projects are also described.
By means of infrared spectroscopy, x-ray diffraction, and differential thermal analysis, the authors investigate the pyrolysis of dichlorodithiourea cadmium, the vapor phase epitaxy of the cadmium sulfide film, and the composition of the solid and gaseous pyrolysis products. Those products are found to include the thiocyanates of guanidine, ammonium, and hydrogen along with cadmium oxides and sulfates and hydrochloric acid.
A general analysis is presented of a photon storage cavity, coupled to free-electron laser (FEL) cavity. It is shown that if the coupling between the FEL cavity and the storage cavity is unidirectional (for example, a ring resonator storage cavity) then storage is possible, but that if the coupling is bi-directional then storage is not possible. Parameters are presented for an infra-red FEL storage cavity giving an order of magnitude increase in the instantaneous photon power within the storage cavity. 4 refs., 3 figs.
The possibility of applying the near infrared gas dynamic lasers (GDL) for neutralization of negative ion beams is examined. A criterion of neutralization is suggested. The use of the criterion makes it possible to select an optically active medium for a negative ion neutralization. To demonstrate the method media containing hydrohalogens as imitating molecules are taken. ((orig.))
Anti-TAG-72 monoclonal antibodies target the tumor-associated glycoprotein (TAG)-72 in various solid tumors. This study evaluated the use of anti-TAG-72 monoclonal antibodies, both murine CC49...Full Text Available
Research continued on low severity coal liquefaction. Research using high temperature infrared of cyclic olefins progressed well during this quarter. Several fluorinated solvents were found that provide a high temperature medium for isotetralin and its aromatic and aliphatic analogues.
This past year has been very exciting for the experimental free-electron laser (FEL) programs. At three Laboratories, oscillator experiments were performed with wavelengths from the visible to far infrared. The output powers are steadily advancing. The status of these programs will be discussed. As shorter wavelengths and higher powers are pursued, higher currents with improved beam quality will be required. Advanced electron linacs should be developed to meet these demands. 13 references, 5 figures, 3 tables.
The interactions of the hydrophobic pulmonary surfactant proteins SP-B and SP-C with 1,2-dipalmitoylphosphatidylcholine in mixed, spread monolayer films have been studied in situ at the air/water interface...Full Text Available
An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age-hardening and moisture susceptibility was conducted. Rheological and infrared analyses of the unaged and aged asphalts and blends were then conducted to evaluate oxidative age-hardening. 18 refs., 5 figs., 6 tabs.
Moderate-resolution, near-infrared spectra between 0.8 and 5.2 #mu#m were obtained for 12 late-type (K0-M3) disk-bearing members of the #approx#5 Myr old Upper Scorpius OB association using SpeX on the NASA Infrared Telescope Facility. For most sources, continuum excess emission first becomes apparent between #approx#2.2 and 4.5 #mu#m and is consistent with that produced by single-temperature blackbodies having characteristic temperatures ranging from #approx#500 to 1300 K. The near-infrared spectra for 5 of 12 Upper Scorpius sources exhibit Pa#gamma#, Pa#beta#, and Br#gamma# emission, indicators of disk accretion. Using a correlation between Pa#beta# and Br#gamma# emission line luminosity and accretion luminosity, mass accretion rates ( M-dot ) are derived for these sources that range from M-dot = 3.5x10"-"1"0 to 1.5 x 10"-"8 M_s_u_n yr"-"1. Merging the SpeX observations with Spitzer Space Telescope ...
Results from scanning electron microscopy, Fourier transform infrared spectroscopy and the measurement of thermally stimulated current show that a high density of the physical defects and the chemical defects are introduced into the surface of the silicone rubber plates after they are treated by corona discharge plasma. These defects behave electrically as shallow electron traps, leading to the formation of a uniform discharge in air at higher pressure when the corona-modified silicone rubber is used in dielectric barrier discharge.
Amyloid-β (Aβ) deposits have been identified as key players in the progression of Alzheimer’s disease (AD). Recent evidence indicates that the deposits probably precede...Full Text Available
Polyacrylonitrile films have been spin cast and pyrolyzed to produce thin (500--1500 A) carbon films. These films have higher electrical conductivities than films produced by other methods at similar temperatures. The conductivity can be varied by at least four orders of magnitude by changing the pyrolysis temperature. Ultraviolet, infrared, and Raman spectroscopies were used to investigate the chemical structure of the films during different stages of processing.
The general n-point massless p-adic Feynman amplitude with arbitrary parameters of analytic regularization for each line is calculated. This result is presented in the form of a sum over hierarchies of a given graph. The structure of ultraviolet and infrared divergences of p-adic Feynman amplitudes is characterized and the star-triangle uniqueness identity in the p-adic case is derived. (orig.).
Using high resolution and high sensitivity IRAS data at 12 and 25 microns low mass stars were studied which have recently formed in the Ophiuchus, Corona Australis, and IC1396 dark clouds. The successful application of these techniques to the Rho Ophiuchi infrared cluster is briefly described. The status of research performed is also presented.
A new era for the field of Galactic structure is about to be opened with the advent of wide-area digital sky surveys. In this article, the author reviews the status and prospects for research for 3 new ground-based surveys: the Sloan Digital Sky Survey (SDSS), the Deep Near-Infrared Survey of the Southern Sky (DENIS) and the Two Micron AU Sky Survey (2MASS). These surveys will permit detailed studies of Galactic structure and stellar populations in the Galaxy with unprecedented detail. Extracting the information, however, will be challenging.
We discuss the determination of the infrared singularities of massive one-loop 5-point functions with Mellin-Barnes (MB) representations. Massless internal lines may lead to poles in the {epsilon} expansion of the Feynman diagram, while unresolved massless final state particles give endpoint singularities of the phase space integrals. MB integrals are an elegant tool for their common treatment. An evaluation by taking residues leads to inverse binomial sums. (orig.)
This critical review with 28 references examines absorption and emission in the v2 band of the carbon dioxide molecule at around the 15micron wavelength. The argument for additional infrared absorption, the enhanced greenhouse effect due to increased carbon dioxide concentrations, and radiation transport and increased emissions are discussed. Experiments studying the transmission spectra of pure carbon dioxide and carbon dioxide in nitrogen, and comparing them with the results of climate modelling using the HITRAN and GEISA databases, are described.
This article presents the text of a lecture delivered by American Educational Research Association President Carol D. Lee at the 29th Annual Charles H. Thompson Lecture-Colloquium Series which was held on November 5, 2008. In her lecture, Lee discussed several points of similarities between W. E. B. Du Bois and President Barack Obama. These similarities in background, education, and in their ideas on politics and power are historically connected with implications for educating Black people though race consciousness.
The energy fed by active galactic nuclei to the surrounding diffuse baryons changes the latter's amount, temperature, and distribution; so in groups and in member galaxies it affects the X-ray luminosity and also the Sunyaev-Zel'dovich effect. Here we compute how the latter is enhanced by the transient blastwave driven by a shining quasar, and is depressed when the equilibrium is recovered with a depleted density. We constrain such depressions and enhancements with the masses of relic black holes in galaxies and the X-ray luminosities in groups. We discuss how all these linked observables can tell the quasar contribution to the thermal history of the baryons pervading galaxies and groups.
We consider a holographic description of a system of strongly-coupled fermions in 2+1 dimensions based on a D7-brane probe in the background of D3-branes. The black hole embedding represents a Fermi-like liquid. We study the excitations of the Fermi liquid system. Above a critical density which depends on the temperature, the system becomes unstable towards an inhomogeneous modulated phase which is similar to a charge density and spin wave state. The essence of this instability can be effectively described by a Maxwell-axion theory with a background electric field. We also consider the fate of zero sound at non-zero temperature.
This invention is concerned with a solar energy system for propelling aircraft. Obtained are forces for aerodynamic lift and impetus. The lifted body had a transparent upper surface for the sun light, but black or reflecting for IR-radiation and high thermal insulation properties. Inside of the lifted body, the air temperature increases and is lifted by convection influence. The air resistance of this body is low in horizontal direction and higher in vertical position. The payload could be shifted, so that the positive or negative angle of the whole body can be selected. By this principal it is possible to transform the static lifting force in a dynamic impetus.
A basic problem in gravitational physics is the resolution of spacetime singularities where general relativity breaks down. The simplest such singularities are conical singularities arising from orbifold identifications of flat space, and the most challenging are spacelike singularities inside black holes (and in cosmology). Topology changing processes also require evolution through classically singular spacetimes. I briefly review how a phase of closed string tachyon condensate replaces, and helps to resolve, basic singularities of each of these types. Finally I discuss some interesting features of singularities arising in the small volume limit of compact negatively curved spaces and the emerging zoology of spacelike singularities.
It has been proposed that a hidden conformal field theory (CFT) governs the dynamics of low frequency scattering in a general Kerr black hole background. We further investigate this correspondence by mapping higher order corrections to the massless wave equations in a Kerr background to an expansion within the CFT in terms of higher dimension operators. This implies the presence of infinite towers of CFT primary operators with positive conformal dimensions compatible with unitarity. The exact Kerr background softly breaks the conformal symmetry and the scaling dimensions of these operators run with frequency. The scale-invariant fixed point is dual to a degenerate case of flat spacetime.
A rocket borne experiment to measure the temperature structure of the inner solar corona via the doppler broadening of the resonance hydrogen Lyman-..cap alpha.. (lambda1216A) radiation scattered by ambient neutral hydrogen atoms was attempted during the 16 Feb 1980 solar eclipse. Two Nike-Black Brant V sounding rockets carrying instrumented payloads were launched into the path of the advancing eclipse umbra from the San Marco satellite launch platform 3 miles off the east coast of Kenya.
We disclose the behavior of quantum and classical correlations among all the different spatial-temporal regions of a space-time with an event horizon, comparing fermionic with bosonic fields. We show the emergence of conservation laws for entanglement and classical correlations, pointing out the crucial role that statistics plays in the information exchange (and more specifically, the entanglement tradeoff) across horizons. The results obtained here could shed new light on the problem of information behavior in noninertial frames and in the presence of horizons, giving better insight into the black-hole information paradox.
The removal of Reactive Black 5 dye in an aqueous solution by electrocoagulation (EC) as well as addition of flocculant was investigated. The effect of operational parameters, i.e. current density, treatment time, solution conductivity and polymer dosage, was investigated. Two models, namely the artificial neural network (ANN) and the response surface method (RSM), were used to model the effect of independent variables on percentage of dye removal. The findings of this work showed that current density, treatment time and dosage of polymer had the most significant effect on percentage of dye removal (p0.8). PMID:21411950
We investigate, from a spacetime perspective, some aspects of Horowitz's recent conjecture that black strings may catalyze the decay of Kaluza-Klein spacetimes into a bubble of nothing. We identify classical configurations that interpolate between flat space and the bubble, and discuss the energetics of the transition. We investigate the effects of winding tachyons on the size and shape of the barrier and find no evidence at large compactification radius that tachyons enhance the tunneling rate. For the interesting radii, of order the string scale, the question is difficult to answer due to the failure of the {alpha}' expansion.
The production of and emission factors for the air-polluting matters sulfur dioxide, nitrogen oxides, carbon monoxide, hydrocarbons (esp. benz(a)pyrene), aldehyde and soot with regard to natural gas, excluding process furnaces, are dealt with. The comparison with other fuels indicates that only as to nitrogen oxides and carbon monoxide are emission factors equal in order of magnitude. As a summary measure of all air-polluting matters the emission index as proposed already in 1972 is applied. It shows emissions with single-room furnaces for heating oil EL to be six times as high as with natural gas; with black-coal briquettes the factor is at least 33, with wood chimneys about 200.
Methods are discussed for optimization of organizational model of longwall mining. Operations at a working face, their duration, number of miners, miner qualifications are analyzed. The so-called method for allocation of heteregeneous resources is used. Using the method optimum organizational models of working faces are constructed. The models consider working conditions, coal output, personnel, miner qualifications, duration of various operations and of idletime, and safety regulations. A computer code developed by the author for optimizing organizational models of longwall mining is described. 9 refs.
A general relativistic model for the formation and acceleration of lowmass-loaded jets from systems containing accreting black holes is presented. The model is based on previous numerical results and theoretical studies in the Newtonian regime, but modified to include the effects of space-time curvature in the vicinity of the event horizon of a spinning black hole. It is argued that the boundary layer between the Keplerian accretion disk and the event horizon is best suited for the formation and acceleration of the accretion-powered jets in active galactic nuclei and micro-quasars. The model presented here is based on matching the solutions of three different regions: i- a weakly magnetized Keplerian accretion disk in the outer part, where the transport of angular momentum is mediated through the magentorotational instability, ii- a strongly magnetized, advection-dominated and turbulent-free boundary layer (BL) between the outer cold accretion ...
The total area (s m) of Voronoi-Dirichlet polyhedron faces corresponding to all intermolecular contacts of one molecule in the structure of crystals and the total volume of pyramids (V m) built on such faces and containing the nuclei of atoms participating in intermolecular contacts in their vertices were determined for 19 unsaturated hydrocarbons. The differential molar heat of adsorption of the hydrocarbons on graphitized thermal carbon black was found to be linearly related to the s m or V m integral parameters of their Voronoi-Dirichlet polyhedra. Aromatic hydrocarbons on the one hand and saturated hydrocarbons, olefins, and acetylene on the other are characterized by different dependences because of the special shapes of their molecular Voronoi-Dirichlet polyhedra.
The total area ( s m) of Voronoi-Dirichlet polyhedron faces corresponding to all intermolecular contacts of one molecule in the structure of crystals and the total volume of pyramids ( V m) built on such faces and containing the nuclei of atoms participating in intermolecular contacts in their vertices were determined for 19 unsaturated hydrocarbons. The differential molar heat of adsorption of the hydrocarbons on graphitized thermal carbon black was found to be linearly related to the s m or V m integral parameters of their Voronoi-Dirichlet polyhedra. Aromatic hydrocarbons on the one hand and saturated hydrocarbons, olefins, and acetylene on the other are characterized by different dependences because of the special shapes of their molecular Voronoi-Dirichlet polyhedra.
A black-disc model combined with accurate matter densities has been used for an investigation of reaction cross sections for {sup 3}He, {sup 4}He and {sup 12}C projectiles. A simple relation is derived between the energy dependence of the reaction cross sections and the strength of the nucleon-nucleon interaction. A comparison is also made of the reaction cross sections for {sup 3}He and {sup 4}He for six different nuclei {sup 12}C, {sup 16}O, {sup 40}Ca, {sup 58,60}Ni and {sup 208}Pb.
Exact solutions are found for the Chandrasekhar Page angular equation which results when the Dirac equation in a Kerr Newman space time is separated into its radial and angular parts. The solutions turn out to be remarkably simple in form while satisfying the asymptotic conditions deduced earlier. The eigenvalues are found to be the square root of the total angular momentum as first found by Dirac for flat space; supplemented by a term which is the product of the mass of the Dirac particle times the specific angular momentum of the black hole. The additional contribution is what is expected from frame dragging.
The method of an effective potential is used to investigate the possible types of evolution of vacuum shells in the Friedmann-Schwarzschild world. Such shells are assumed to emerge during phase transitions in the early Universe. The possible global geometries are constructed for the Friedmann-Schwarzschild worlds. Approximate solutions to the equation of motion of a vacuum shell have been found. The conditions under which the end result of the evolution of the vacuum shells under consideration is the formation of black holes and wormholes with baby universes inside have been found. The interior of this world can be a closed, flat, or open Friedmann universe.
The key component for improving the energy efficiency and cycle life of the electrically rechargeable zinc-air battery is the bifunctional air electrode. The air electrodes described in this paper contained different types of carbon black as the substrate for the perovskite catalyst (La{sub 0.6}Ca{sub 0.4}CoO{sub 3}). Morphological and physical properties of the carbon substrates play an important role in enhancing the activity and stability of the bifunctional air electrode. Current-potential curves and cycle-life tests were applied in order to gather information on the activity and stability of these electrodes. (authors)
The thermodynamic characteristics of adsorption of iodobenzene, 2-iodothiophene, and 1- and 2-iodoadamantanes on the surface of graphitized thermal carbon black were determined experimentally. The influence of the special features of the molecular structure of the adsorbates on the thermodynamic characteristics of adsorption was studied. The atom-atom approximation of the semiempirical molecular-statistical theory of adsorption was used to calculate the thermodynamic characteristics of adsorption of the adsorbates using the newly determined potential function parameters of pair intermolecular interaction (?(r)) of I with C atoms of the basal graphite face. For the example of isostructural monohalogenated benzenes, thiophenes, and adamantanes, a comparative analysis of the contributions of ...
A revision of some basic concepts related to the analysis of variance of repeated measures is presented within an ecological context topics such as the types of experiments in which the technique is applicable, the hypotheses of interest, and its preference over other traditional techniques such as regression and conventional analysis of variance, are discussed. As an example, the technique was successfully applied to an experiment carried out at Cienaga Grande de Santa Marta, Colombia, in which the concentration of cadmium #mu#g/g in leaves of the black mangrove Avicennia germinans was measured in several monitoring stations and throughout several sampling intervals representing seasons.
The adsorption properties of four samples of ..cap alpha..-BN were studied by means of gas chromatography. The particles of ..cap alpha..-BN particles, according to data obtained by electron microscopy, have the shape of thin platelets. A sample of ..cap alpha..-BN prepared from magnesium polyboride was found to be the most nearly homogeneous adsorbent. For a number of n-alkanes, benzene, and alkylbenzenes, data have been obtained on the retention volumes (Henry constants) and the differential heats of adsorption for surface coverages approaching zero. These thermodynamic data on the adsorption showed that ..cap alpha..-BN, like graphitized thermal carbon black, is a nonspecific adsorbent.
The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.
Abstract Unrefined and refined black raspberry seed oils (RSOs) were examined for their lipid-modulating effects in male Syrian hamsters fed high-cholesterol (0.12% g/g), high-fat (9% g/g) diets. Hamsters fed the refined and the unrefined RSO diets had equivalently lower plasma total cholesterol and high-density lipoprotein (HDL) cholesterol in comparison with the atherogenic coconut oil diet. The unrefined RSO treatment group did not differ in liver total and esterified cholesterol from the coconut oil-fed control animals, but the refined RSO resulted in significantly elevated liver total and esterified cholesterol concentrations. The unrefined RSO diets significantly lowered plasma triglycerides (46%; P=.0126) in comparison with the coconut oil diet, whereas the refined RSO only tended to lower plasma triglyceride (29%; P=.1630). Liver triglyceride concentrations were lower in the unrefined (46%; P=.0002) and refined (36%; P=.0005) RSO-fed animals than the ...
We derive improved versions of the relations between supermassive black hole mass (M _B_H) and host-galaxy bulge velocity dispersion (#sigma#) and luminosity (L; the M-#sigma# and M-L relations), based on 49 M _B_H measurements and 19 upper limits. Particular attention is paid to recovery of the intrinsic scatter (#epsilon#_0) in both relations. We find log(M _B_H/M _s_u_n) = #alpha# + #beta#log(#sigma#/200 km s"-"1) with (#alpha#, #beta#, #epsilon#_0) = (8.12 #+-# 0.08, 4.24 #+-# 0.41, 0.44 #+-# 0.06) for all galaxies and (#alpha#, #beta#, #epsilon#_0) = (8.23 #+-# 0.08, 3.96 #+-# 0.42, 0.31 #+-# 0.06) for ellipticals. The results for ellipticals are consistent with previous studies, but the intrinsic scatter recovered for spirals is significantly larger. The scatter inferred reinforces the need for its consideration when calculating local black hole mass function based on the M-#sigma# relation, and further implies that there may be ...
This project, conducted under The United States Department of Energy (DOE) Cooperative Agreement DE-FC36-94GO10002/A002, was part of a multiple-phase effort to develop technologies that improve the energy efficiency and economics of chemical process recovery in the pulp and paper industry. The approach taken was to consider two major alternatives in two phases. Phase I, conducted previously, considered means to improve pulp mill recovery boilers using high-solids advanced combustion of black liquor; while this project, Phase la, considered means to recover kraft pulping mill process chemicals by low-temperature black liquor gasification. The principal steps previously proposed in this program were: (1) Evaluate these two technologies, high-solids advanced combustion and gasification, and then select a path forward using the more promising of these two options for future work. (2) Design and construct a pilot-scale unit based on the selected ...
The eastern oyster (Crassostrea virginica) developed neoplastic disorders when experimentally exposed both in the laboratory and field to chemically contaminated sediment from Black Rock Harbor (BRH), Bridgeport, Connecticut. Neoplasia was observed in oysters after 30 or 60 days of continuous exposure in a laboratory flow-through system to a 20 mg/L suspension of BRH sediment plus postexposure periods of 3, 30, or 60 days. Composite tumor incidence was 13.6% for both exposures. Tumor occurrence was highest in the renal excretory epithelium, followed in order by gill, gonad, gastrointestinal, heart, and embryonic neural tissue. Regression of experimental neoplasia was not observed when the stimulus was discontinued. In field experiments, gill neoplasms developed in oysters, deployed in cages for 30 days at BRH and 36 days at a BRH dredge material disposal area in Central Long Island Sound, and kidney and gastrointestinal neoplasms developed in caged oysters deployed ...
The kraft recovery boiler is of critical importance for the paper and pulp industry. From only energy point of view, kraft recovery boilers supply more than 50% of total thermal energy consumed in the paper and pulp industry. A kraft recovery boiler has two main functions: firstly to recover the inorganic cooking chemicals in the black liquor for reuse in the pulping process, and secondly to make use of the chemical energy in the organic portion of the black liquor to generate super-heated steam for the plant. The twin objectives of recovering chemicals and energy makes the recovery boiler design and operation more complex than virtually any other boiler application. Thus there is a demand for development of an analytical tool that can be used to predict the performance of a kraft recovery boiler. This paper presents the results achieved from a project jointly financed by Swedish National Energy Administration and the industry (Iggesund ...
We report five new measurements of central black hole masses based on Space Telescope Imaging Spectrograph and Wide Field Planetary Camera 2 observations with the Hubble Space Telescope (HST) and on axisymmetric, three-integral, Schwarzschild orbit-library kinematic models. We selected a sample of galaxies within a narrow range in velocity dispersion that cover a range of galaxy parameters (including Hubble type and core/power-law surface density profile) where we expected to be able to resolve the galaxy's sphere of influence based on the predicted value of the black hole mass from the M-#sigma# relation. We find masses for the following galaxies: NGC 3585, M _B_H = 3.4"+"1"."5 _-_0_._6 x 10"8 M _s_u_n; NGC 3607, M _B_H = 1.2"+"0"."4 _-_0_._4 x 10"8 M _s_u_n; NGC 4026, M _B_H = 2.1"+"0"."7 _-_0_._4 x 10"8 M _s_u_n; and NGC 5576, M _B_H = 1.8"+"0"."3 _-_0_._4 x 10"8 M _s_u_n, all significantly excluding M _B_H = 0. For NGC 3945, M _B_H = ...
The influence of additionally injected short-wavelength photobleaching light on the radiation hardness of Ge-doped graded index fibers working at 1,300 nm wavelength is investigated. Predictions are complicated by the fact that more efficient shortwave bleaching light experiences higher radiation-induced loss. Promising results are found for low fiber temperatures (approx-lt -50 C) and bleaching light of about 835 nm wavelength.
A program was undertaken to radiation harden an existing power integrated circuit technology (BCDMOS) to total dose, gamma dot, SEU, and neutrons. Efforts have centered around hardening and optimizing our CMOS, DMOS, and NPN devices. Initial results indicate a substantial improvement in hardness over our existing commercial technology.
The quantitative imaging of a phase object using 16 keV x-rays is reported. The theoretical basis of the techniques is presented along with its implementation using a synchrotron x-ray source. It is found that the phase image is in quantitative agreement with independent measurements of the object. 13 refs., 5 figs.
Olive oil mill wastewaters (OMW) cause disposal problems because they contain powerful pollutants such as phenolic compounds. Complete biodegradation or removal of these compounds is hardly achieved by a single treatment method. In this work, we investigated 2 integrated technologies for the treatment of the recalcitrant contaminants of OMW, allowing water recovery and reuse for agricultural purposes. (Author)
In the year 2008, the high pressure partial turbine and two low pressure partial turbines in the hard coal power station Bergkamen (Federal Republic of Germany) were modernized. A three-dimensional blade design and innovative seals were used. This resulted into a distinct increase in efficiency among other things.
The loosening equipment consists of a base machine and four-link suspension mechanism which is a cross frame with loosening gear connected to the base machine by universal hinges. In order to improve the reliability of the machine, the drive of transverse shifting in the cross frame is made of symmetrically arranged, shock-absorbing, hydraulic cylinders which are connected by additional universal hinges to the base machine and the lower pull rods. The design of the loosening machine guarantees its reliable operation on soil with significant quantity of hard inclusions.
With the frequent load changes to which a hard coal power station is subjected in the middle and peak load range, great demands are linked with the transient behaviour of the steam generator. Due to the serial connection of the crusher and boiler, the strongly delaying transient behaviour of the crusher compounds entirely with the transient behaviour of the steam generator. Therefore, a suggestion is to be made here as to the improvement of the dynamics of the crusher.
The influence of RTA (Rapid Thermal Anneal) treatment on MOS radiation hardness is demonstrated and compared with classical furnace treatment. In the case of the RTA, the oxide trapped charge is found to depend on: (i) the anneal temperature as expected, data are in good agreement with a recently developed model of oxygen out-diffusion; (ii) the location across the wafer with a radial dependence, results could be related to stress induced by thermal gradient.
The competitiveness of a new nuclear plant vs. a new oil or gas fired combined cycle plant or a coal fired plant in East-Asia, is reviewed in the paper. Both the nuclear and the fossil fired plants are evaluated as either utility financed or independent power producer (IPP) financed. Two types of advanced light water reactors (ALWRs) are considered in this paper, namely evolutionary ALWRs (1200 MWe size) and passive ALWRs (600 MWe class). A range of capital and total generation costs for each plant type is reported here. The comparison centers on three elements of overall competitiveness: generation costs, hard currency requirements, and employment requirements. Each of these aspects is considered perspective. Year-by-Year generation cost history over the plant lifetime is shown in some cases. It is found here that a utility financed evolutionary and passive ALWRs are broadly competitive with an IPP financed gas fired combined cycle plant and are more economic than ...
A systematic study of structure-mechanical properties relation is reported for MoSi{sub 2}-SiC nanolayer composites. Alternating layers of MoSi{sub 2} and SiC were synthesized by DC magnetron and rf-diode sputtering, respectively. Cross-sectional transmission electron microscopy was used to examine three distinct reactions in the specimens when exposed to different annealing conditions: Crystallization and phase transformation of MoSi{sub 2}, crystallization of SiC, and spheroidization of the layer structures. Nanoindentation was employed to characterize the mechanical response as a function of structural changes. As-sputtered material exhibits amorphous structures in both types of layers and has a hardness of 11 GPa and a modulus of 217GPa. Subsequent heat treatment induces crystallization of MoSi{sub 2} to form the C40 structure at 500C and SiC to form the a structure at 700C. The crystallization process is directly responsible for hardness ...
Platelet-rich plasma (PRP) is a platelet concentrate that has widely been used to accelerate the healing of soft and hard tissues. The preparation of PRP has been described by several authors. Preparation protocols vary from system to system, depending on the concentration of different integrating proteins. The objective of this article is to describe the principal use of PRP mixed with fat grafts in aesthetic plastic surgery.