International Nuclear Information System (INIS)

The RKR potential energy curves are constructed for the ground states of diatomic hafnium oxide and thorium oxide. Using Lippincott and Hulburt-Hirschfelder potential function the dissociation energies are estimated by curve fitting method. The H-H potential function was found to give a better fit in both cases. The dissociation energies of hafnium oxide and thorium oxide are estimated as 9.04 #+-# 0.02 eV and 10.34 #+-# 0.01 eV respectively. (author).

Energy Technology Data Exchange (ETDEWEB)

A hydrous oxide film for the application as dielectric film is synthesized by immersion of pure aluminum in hot water. From a Rutherford backscattering analysis, the ratio of aluminum to oxygen atoms was found to be 3:2 in the anodized aluminum oxide film, and 2:1 in the hydrous oxide layer. Anodization of the hydrous oxide layer was more effective for the transition of amorphous anodic oxides to the crystalline aluminum oxides.

Science.gov (United States)

... AT THE INTERFACE, A THIN OXIDE LAYER IS OBSERVED ALONG WITH POSSIBLE PALLADIUM SILICIDES. PALLADIUM ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a method comprising applying a passivation layer of CaF{sub 2} to the surface of a superconductive ceramic oxide by evaporation. The CaF{sub 2} layer is effective to passivate the oxide surface without disrupting the superconductive properties.

Energy Technology Data Exchange (ETDEWEB)

Dominating factors in plasma nitriding and plasma condition that makes nitriding possible in plasma nitriding process of metals having hard oxide film were studied. In case of stainless steel, oxide film sputtering was easier comparing to nitriding layer. Three phenomena such as sputtering of oxide layer, formation of nitriding layer and sputtering of nitriding layer occurred simultaneously. Nitriding was achieved when the formation of nitriding layer reached the peak comparing to the removal of nitriding layer after the removal of oxide layer. Situations of metallic surface of stainless steel in surface nitriding were divided into four categories and they were, situation where oxide layer remained as it is, situation ...

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the Canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. Bubbles containing ...

Energy Technology Data Exchange (ETDEWEB)

A duplex surface treatment technique based on calorizing and plasma nitriding was developed to improve the wear and oxidation resistance of H13 steel at high temperatures. The effects of the relative thickness of the calorized layer to the depth of plasma nitriding on the wear and oxidation properties at temperatures up to 900 C were investigated in this work. High-temperature wear tests were performed at 500 C with dry conditions in open air using a ball-on-disk type tribotest machine. Isothermal oxidation tests were performed at 900 C for up to 100 h under controlled atmosphere. The results indicated that the specimens with a calorized layer as an intermediate phase between the surface duplex layer and the base metal showed higher wear and oxidation resistance than the specimens with a nitrided layer alone. During ...

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. This report presents ...

International Nuclear Information System (INIS)

High quality graphene sheets are synthesized through efficient oxidation process followed by rapid thermal expansion and reduction by H2. The number of graphene layers is controlled by tuning the oxidation degree of GOs. The higher the oxidation degree of GOs is getting, the fewer the numbers of graphene layers can be obtained. The material is characterized by elemental analysis, thermo-gravimetric analysis, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and Fourier transform infrared spectroscopies. The obtained graphene sheets with single, triple and quintuplicate layers as anode materials exhibit a high reversible capacity of 1175, 1007, and 842 mA h g-1, respectively, which show that the graphene sheets with fewer layers have higher reversible capacity. -- Graphical abstract: The typical TEM ...

International Nuclear Information System (INIS)

In this work, the silicon oxynitride layer was studied as a tunneling layer for non-volatile memory application by fabricating low temperature polysilicon thin film transistors on glass. Silicon wafers were oxynitrided by only nitrous oxide plasma under different radio frequency powers and plasma treatment times. Plasma oxynitridation was performed in RF plasma using inductively coupled plasma chemical vapor deposition. The X-ray energy dispersive spectroscopy was employed to analyze the atomic concentration ratio of nitrogen/oxygen in oxynitride layer. The oxynitrided layer formed under radio frequency power of 150 W and substrate temperature of 623 K was found to contain the atomic concentration ratio of nitrogen/oxygen as high as 1.57. The advantage of high nitrogen concentration in silicon oxide layer formed by using nitrous ...

Energy Technology Data Exchange (ETDEWEB)

The initiation and inhibition of pitting corrosion on zirconium and hafnium in aqueous solutions have been investigated by potentiodynamic, potentiostatic and galvanostatic measurements at 25/sup 0/C. Effects of Cl/sup -/, Br/sup -/and I/sup -/ have been examined over a range of salt concentrations and pH. All three halide ions cause pitting attack on the two metals, but this may be inhibited by other anions. The results show that hafnium is more easily protected against pitting than is zirconium. The data are treated by the Butler-Volmer equation to yield more information about the mechanisms of the pitting corrosion.

International Nuclear Information System (INIS)

The influence of MeV electrons irradiation on the gate oxide layers of hydrogenated polysilicon thin film transistors (TFTs) was investigated by measuring gate leakage currents and threshold voltages. The experimental data revealed a decrease of oxide trap density and increase of positive oxide charge. Improvement in the interface roughness and in the oxide quality near the bottom interface was observed.

International Nuclear Information System (INIS)

Silicon layered structures containing porous silicon modified with various thermal treatments and epitaxial layers deposited on porous layers were studied with a number of complementary X-ray diffraction methods using synchrotron source. The methods of characterization included recording of rocking curves for reflections with various asymmetry as well as projection, section and micro-Laue topography. It was found that oxidizing and sintering of porous silicon seriously modified the strains in the porous layer and in some cases even inverting the sense of strain with respect to that in initially formed porous layer. Consequently the deposited epitaxial layer usually was not laterally coherent with the substrate. Some of investigated layers were not stable in time and after few months period exhibited significant lost of ...

International Nuclear Information System (INIS)

The morphological development of oxide scales formed on a low Al substituted #beta#-sialon (z=0.2) oxidised for time periods up to 1024h at 1350 C is discussed in relation to oxidation kinetics. The oxidation process is observed to be accompanied by changes in both the phase assemblage of the external layers and their morphology. Thus as the time of oxidation increases beyond 64h the cristobalite-#beta#-yttrium disilicate phase assemblage changes to cristobalite plus #beta#- and #gamma#-yttrium disilicate. In addition to the changes observed for the surface layers, differences are observed in the morphologies of the polished cross-sections. These changes are consistent with an order of magnitude decrease in oxidation rate. (orig.).

Science.gov (United States)

The growth of an oxide interfacial layer was recently found to increase the open-circuit voltage (OCV) and efficiency by up to 60 per cent in GaAs metal-semiconductor solar cells. Details of oxidation techniques to provide the necessary oxide thickness and chemical structure and using ozone, water-vapor-saturated oxygen, or oxygen gas discharges are described, as well as apparent crystallographic orientation effects. Preliminary results of the oxide chemistry obtained from X-ray, photoelectron spectroscopy are given. Ratios of arsenic oxide to gallium oxide of unity or less seem to be preferable. Samples with the highest OVC predominantly have As(+3) in the arsenic oxide rather than As(+5). A major difficulty at this time is a reduction in OCV by 100-200 mV when the antireflection coating is vacuum deposited.

International Nuclear Information System (INIS)

Using the PMR method the interaction of zirconium and hafnium tetrachlorides with tri.tet.butylphenyl ester of 1,2- naphthoquinonediazide (2)-5-sulfonic acid is studied. The formation of MCl_4xNQD complexes is established, the equilibrium constants and thermodynamic parameters of complexing reaction are determined. The presence of rapid ligand exchange, proceeding according to associative mechanism, is detected. The rate constants and activation energies of the exchange reaction are calculated.

International Nuclear Information System (INIS)

Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of ...

Energy Technology Data Exchange (ETDEWEB)

Alloy 690 and Alloy600 are used as a material for the steam generator tubing in the pressurized water reactor(PWR) of nuclear power plants due to its high corrosion resistance. Although those are a highly corrosion resistance material, their stress corrosion cracking(SCC) have been found on occasion, which are deeply related to a surface oxide film on a base material which have occurred on the primary side as well as the secondary side of a tubing. And The SCC is accelerated in the existing Pb which is the impurity of secondary steam generator components. The Oxide on a steel surface in an aqueous solution above 100 .deg. C is composed of a duplex film structure. The inner layer of the oxide is dense and less porous, which is formed by a growth of the oxide layer on the metal surface. The outer layer of the oxide is less ...

International Nuclear Information System (INIS)

Marker experiments for studying the mass transport through a palladium silicide layer on a crystalline substrate during thermal oxidation at 700 to 850 deg C have been reported recently. In this work argon gas embedded in amorphous silicon during sputtering was implemented as the inert marker and the oxidation of PdSi was processed above 900 deg C. At this high-temperature oxidation silicon-rich silicide PdSisub(y), with y exceeding 5, may be obtained. This can be anticipated by considering the Pd-Si phase diagram which shows the liquid phase may appear at an annealing temperature above 892 deg C. As a result, a non-stoichiometric and non-uniform silicide layer may develop at the sample surface. Marker analysis showed that both palladium and silicon dissociated at the Pdsub(x)Si/ SiO_2 interface and moved to the substrate with the silicon being the dominant diffuser. The Rutherford ...

Energy Technology Data Exchange (ETDEWEB)

The solar central receiver at the Barstow Pilot Plant is a once-through steam boiler consisting of vertical arrays of Alloy 800 tubes. Water/steam leaks associated with tube bends near the receiver outlet were observed after 16 service months. The leaks resulted from through-wall cracks localized in the crown of tube bends operating in the temperature range from 550 to 650/sup 0/C. Initiation occurred on the ID (steam side) of the tube and propagated transgranular through the tube wall. Cracking was axial and circumferential; in general, the circumferential cracks were more severe than the axial cracks. Thick oxide layers showed on the ID of the receiver tubes; a 25-..mu..m thick oxide layer had formed on tubing which operated at 650/sup 0/C. In addition, an enhanced oxidation layer was observed along a narrow band in the crown of the tube. This band was up to ...

International Nuclear Information System (INIS)

By means of an audio frequency plasma polymerisation ultra-thin gradient plasma polymer layers were deposited on zinc and zinc-coated iron. The aim was to generate an interfacial polymeric layer which bonds to an oxidised metal as well as to a subsequently applied organic coating and acts as an interfacial barrier layer for ions and water. Surface modifications were done in an in situ plasma cell with infrared reflection absorption spectroscopy (IRRAS). The zinc surface was first activated by an oxygen plasma to provide a freshly oxidised and contamination free oxide surface. The intermediate stages of the surface reactions could be revealed. Carbon dioxide molecules as oxidation products adsorbed on the growing zinc oxide and were desorbed at a later stage. An organosilicon plasma polymer was deposited directly on top of the oxide ...

Energy Technology Data Exchange (ETDEWEB)

Photocurrent and capacitance measurements of semiconductor passive films formed on metals and alloys can be used to study the electronic properties and reveal indirect information about structure and composition. The current work used these techniques to investigate the electronic properties of the passive films formed on three austenitic stainless steels, types 304L, 316L and 254SMO, in borate. Evidence was found for the existence of a large number of localised mid bandgap states, consistent with amorphous oxides. However, the flat-band potentials of the austenitic stainless steel passive films were found to be independent of both composition and measuring frequency. The most credible explanation for the bandgap values determined from photocurrent measurements is that the passive films are formed as dual layers, iron oxide outer layer and chromium oxide inner ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports the results of leaching experiments conducted with and without Thiobacillus ferroxidans at the same conditions in solution. The extent of leaching of ZnS with Bacteria is significantly higher than that without bacteria at high concentrations of ferrous ions. A porous layer of elemental sulfur is present on the surfaces of the chemically leached particles, which no sulfur is present on the surfaces of the bacterially leached particles. The analysis of the data using the shrinking-core model shows that the chemical leaching of ZnS is limited by the diffusion of ferrous ions through the sulfur product layer at high concentrations of ferrous ions. The analysis of the data shows that diffusion through the product layer does not limit the rate of dissolution when bacteria are present. This suggests that the action of T.ferroxidans in oxidizing the sulfur formed on the particle surface is to ...

Energy Technology Data Exchange (ETDEWEB)

MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. ...

Energy Technology Data Exchange (ETDEWEB)

Passive films were formed on chromium by polarization at +400 mV/SHE in 0.5 M H{sub 2}SO{sub 4} for different times (30 minutes, 2 hours and 20 hours) without and with chlorides. The effect of chlorides was studied by adding NaCl to the solution before or after passivation. The chloride concentrations were 0.05, 0.3 and 1 M. The (i-E) curves recorded for Cr without and with Cl{sup -} are similar and the addition of chlorides after passivation has no significant effect on the current recorded in the passive state. The passive films were analyzed by angle-resolved XPS (AR-XPS). The measurements performed at different take-off angles of the photoelectrons show that the films have a bilayer structure constituted of an outer hydroxide layer, Cr(OH){sub 3}, and an inner oxide layer, Cr{sub 2}O{sub 3}. The thicknesses of the oxide and hydroxide layers are 3 A and 9 A, 6 A and 7 A and 6 A ...

Energy Technology Data Exchange (ETDEWEB)

Alloy 600 is commonly used in the primary systems of PWR plants because of its excellent resistance to a stress corrosion cracking and pitting. But a stress corrosion cracking and pitting corrosion are occasionally observed under PWR conditions, which may be correlated with the passive film on the Alloy 600 surface. There is little information on the composition of films growing on the surface of Alloy 600 at high temperature. Therefore, an understanding of the basic electrochemical behaviors about an anodic dissolution and the passivation of the bare surface of metals and alloys provides important information about localized corrosions like a SCC and pitting. Oxide on the steel surfaces in an aqueous solution above 100 .deg. C is composed of a duplex film structure. The inner layer of the oxide is dense and less porous, which is formed by a growth of the oxide layer on the metal ...

Energy Technology Data Exchange (ETDEWEB)

The verification test program on zinc injection applicability to Japanese BWRs was started in 1997. Laboratory tests using high temperature water loops under BWR reactor water conditions are in progress. This paper is an interim report on results obtained so far. Co-58 and Zn-65 were simultaneously used in the Co radioactivity buildup test to evaluate zinc injection suppression effects towards cobalt deposition on pre-oxidized stainless steel. The following results were obtained. The Co deposition was suppressed effectively by Zn injection, even when there was a pre-oxide film. For the test piping that had the pre-oxide film formed under the NWC (normal water chemistry) condition, when soaked under the HWC (hydrogen water chemistry) condition a large amount of Co-58 was taken into a small part of the inner layer. The distribution ratio of Co-58 in the inner layer and outer ...

Energy Technology Data Exchange (ETDEWEB)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier ...

Energy Technology Data Exchange (ETDEWEB)

Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window ...

International Nuclear Information System (INIS)

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.

International Nuclear Information System (INIS)

For obtaining radiation less damagable laser mirrors, a preliminary optimization of film fabrication suitable for the analysis of laser damage mechanism has been done as the first step. Here, the optimization requires not only the stable fabrication process but also the ideal film structure i.e., the amorphous and smooth film structure simultaneously, eliminating latently unwanted secondary effects such as light scattering during laser damage test. For this purpose, we adopted the ion assisted deposition (IAD) method and modified the deposition conditions for titanium and tantalum oxide films, both of which compose typical high index layers, and where SiO_2 layers are also chosen as low index layers because of their amorphous and smooth nature, in alternative multilayer laser mirrors. Surface and cross sectional film structures and film crystallinity are compared and characterized, using a high ...

International Nuclear Information System (INIS)

This report summarizes the findings of a five-month LDRD project funded through Sandia's NTM Investment Area. The project was aimed at providing the foundation for the development of advanced functional materials through the application of ultrathin coatings of microporous or mesoporous materials onto the surface of substrates such as silicon wafers. Prior art teaches that layers of microporous materials such as zeolites may be applied as, e.g., sensor platforms or gas separation membranes. These layers, however, are typically several microns to several hundred microns thick. For many potential applications, vast improvements in the response of a device could be realized if the thickness of the porous layer were reduced to tens of nanometers. However, a basic understanding of how to synthesize or fabricate such ultra-thin layers is lacking. This report describes traditional and novel approaches to the ...

Energy Technology Data Exchange (ETDEWEB)

Sputter-deposited tantalum (Ta) and reactively sputter-deposited Ta-nitride films were studied with respect to the passivation capability against copper (Cu) oxidation in thermal O{sub 2} ambient. A 200 {angstrom} Ta or Ta-nitride film was sputter-deposited on a 2,000 {angstrom} Cu film using a Ta target in an Ar/N{sub 2} gas mixture. With Ta passivation, Cu was not oxidized at temperatures up to 400 C, which can be further improved by using passivation of an amorphous Ta-nitride film deposited in an appropriate condition. The absence of long-range defects in the Ta-nitride film was presumably responsible for this improvement. However, sputtering-induced surface damage by excess N{sub 2} in the sputter gas mixture may reduce the passivation capability of Ta-nitride films. When the passivated Cu was oxidized, the Cu oxides always resided in the top surface region. That is, in the ...

International Nuclear Information System (INIS)

The construction materials used in coolant systems in nuclear power plants become covered with oxide films as a result of exposure to the aqueous environment. The susceptibility of the materials to different forms of corrosion, as well as the extent of the incorporation of radioactive species on the surfaces of the primary circuit, are greatly influenced by the physical and chemical properties of these oxide films. The composition and characteristics of the oxide films in turn depend on the applied water chemistry. This work was undertaken in order to collect and evaluate the present views on the structure and behaviour of oxide films formed on iron- and nickel-based materials in aqueous environments. This survey should serve to recognise the areas in which more understanding and research effort is needed. The review begins with a discussion on the bulk oxides of iron, nickel and ...

Energy Technology Data Exchange (ETDEWEB)

Semiconductor properties of passive films formed on the Fe-18Cr alloy in a borate buffer solution (pH = 8.4) and 0.1 M H{sub 2}SO{sub 4} solution were examined using a photoelectrochemical spectroscopy and an electrochemical impedance spectroscopy. Photo current reveals two photo action spectra that derived from outer hydroxide and inner oxide layers. A typical n-type semiconductor behaviour is observed by both photo current and impedance for the passive films formed in the borate buffer solution. On the other hand, a negative photo current generated, the absolute value of which decreased as applied potential increased in the sulfuric acid solution. This indicates that the passive film behaves as a p-type semiconductor. However, Mott-Schottky plot revealed the typical n-type semiconductor property. It is concluded that the passive film on the Fe-18Cr alloy formed in the borate buffer solution is composed of both n-type outer hydroxide and inner ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the effects of SiC coating on the oxidation resistance of C/C composites in combusting fields, which are expected to be applied to high temperature structural materials at over 1770K. The coating methods employed were CVD and pack cementation. The time changes in weight loss of the specimens were measured at temperatures of 1770K and 1900K under the equivalence ratio of 0.9 generated by methane-air combustion, and the surface of the specimens before and after the experiment was observed by SEM. Although the weight loss of the specimens coated by the CVD method was minimal, the coating layer was easily peeled off from the substrate. On the other hand, the layer of the specimens coated by the pack cementation method was stable and adhered to the substrate, but the substrate was degraded because of penetration of oxygen through the pores in the layer. To cover the pores, the specimens ...

International Nuclear Information System (INIS)

The effect of pigments on the development of corrosion products between the painting system and metal surface when exposed to marine environments has been discussed. The pigments studied were: red mud zinc chromate, zinc chromate, red oxide zinc phosphate, manganese phosphate barium chromate and basic lead silico chromate. Moessbauer spectroscopy revealed that the upper rust layer in all the cases consisted of #gamma#-Fe_2O_3, #gamma#-FeOOH and #alpha#-FeOOH. The lower rust layer immediately in contact with the metal surface consisted of an asymmetrical doublet due to #gamma#-FeOOH. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

The effect of Mo addition as an alloying element to stainless steel alloys is investigated by capacitance (Mott Schottky approach), and photoelectrochemistry measurements. Complementary studies were made using Auger electron spectroscopy and X-ray photoelectron spectroscopy. The Mott-Schottky approach and the photoelectrochemical studies showed that the presence of Mo as an alloying element affects the semiconductive properties of the oxide films. The analytical results have shown that the oxide films formed on stainless steels are composed by an external Fe rich region and an inner Cr rich region. No significant amount of Mo was found in the outer layers of the film. The presence of Mo leads to an increase of the chromium content in the inner layers of the film, although without increasing the film thickness. (orig.) 30 refs.

Energy Technology Data Exchange (ETDEWEB)

Chemical characterization of passive films formed on AISI 304 austenitic stainless steel, in a borate/boric acid solution at pH 9.2, under various conditions of potential, temperature, and polarizations time, was made by Auger electron spectroscopy combined with ion sputtering, and x-ray photoelectron spectroscopy (XPS). The depth chemical composition, thickness, and duplex character of the passive layers were determined after processing AES sputter profiles by their quantitative approach based on the sequential layer sputtering model. Moreover, separated contributions of elements in their oxidized and unoxidized state could be disclosed from part to part of the oxide-alloy interface. The XPS study specified the chemical bondings which take placed inside the film, between Fe and oxygen (and water).

International Nuclear Information System (INIS)

The influence of high energy electron (23 MeV) irradiation on the electrical characteristics of p-channel polysilicon thin film transistors (PSTFTs) was studied. The channel 220 nm thick LPCVD (low pressure chemical vapor deposition) deposited polysilicon layer was phosphorus doped by ion implantation. A 45 nm thick, thermally grown, SiO_2 layer served as gate dielectric. A self-alignment technology for boron doping of the source and drain regions was used. 200 nm thick polysilicon film was deposited as a gate electrode. The obtained p-channel PSTFTs were irradiated with different high energy electron doses. Leakage currents through the gate oxide and transfer characteristics of the transistors were measured. A software model describing the field enhancement and the non-uniform current distribution at textured polysilicon/oxide interface was developed. In order to assess the irradiation-stimulated ...

International Nuclear Information System (INIS)

Basic studies of the oxidation resistance of Fe-Cr binary and Fe-Cr-Ni ternary alloys in pure oxygen have shown that the excellent corrosion resistance of Alloy 800 is explicable in terms of the low defect concentrations and diffusion rates in the oxide forming on alloys of this composition in sufficiently oxidising environments. The performance of Alloy 800 in environments of particular importance to nuclear power generation is briefly reviewed to determine to what extent ideas derived from the basic studies of Fe-Cr-Ni ternary alloys are borne out in practice. The good corrosion resistance of Alloy 800 in steam and CO_2 and, to some extent, in molten salt environments is in agreement with the behaviour of ternary alloys in oxygen. Minor aliovalent alloying additions are only expected to have a significant effect on the oxidation resistance of Alloy 800 if they favour the formation of breakthrough duplex ...

Energy Technology Data Exchange (ETDEWEB)

Boron is implanted in crystalline silicon through oxide layers with different thicknesses. The implantation is carried out at various doses and energies of interest in ultra large scale integration (ULSI) application. Rapid thermal annealings (RTA) are used to obtain shallow junctions and electrical activation of the B atoms. However, transient enhanced diffusion induced by implantation damage can be observed. The boron concentration profiles before and after annealing are obtained with secondary ion mass spectrometry (SIMS). It is found that the diffusion transient in the tail region of the boron profile increases with decreasing oxide thickness. Even more, if the implantation damage concerns mostly the oxide, i.e. when the concentration peak is located in this oxide, the oxygen knocked into the silicon substrate could play this way an important role in restricting the boron ...

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

Energy Technology Data Exchange (ETDEWEB)

The indium implant damage and diffusion behavior in thin silicon-on-insulator (SOI) with a 200 nm top silicon layer were studied for different implantation energies and doses. Rutherford backscattering spectrometry in the channeling mode (RBS/C) was used to characterize the implant damage before and after annealing. Secondary ion mass spectrometry (SIMS) was used to study the indium transient enhanced diffusion (TED) behavior in the top Si layer of the SOI structure. An anomalous redistribution of indium after relatively high energy (200 keV) and dose (1 x 10{sup 14} cm{sup -2}) implantation was observed in both bulk Si and SOI substrates. However, there exist differences in these two substrates that are attributable to the more predominant out-diffusion of indium as well as the influence of the buried oxide layer in the SOI structure.

Energy Technology Data Exchange (ETDEWEB)

A major factor for the achievement of the desirable performance, efficiency and lifetime of flexible organic electronic devices is the optimization of the encapsulation layers that protect the device active layers by atmospheric gas molecule permeation. The active layers consisted of small molecule and/or polymer organic semiconductors as well as the organic conductors need to be encapsulated into a transparent medium that will provide the necessary protection and maintain their charge generation and transport characteristics. The encapsulation layers are generally consisted of inorganic thin films (silicon oxide-SiO{sub x} and aluminium oxide-AlO{sub x}) deposited onto the polymeric substrates, such as PolyEthylene Terephthalate (PET). In this work, in situ and real-time Spectroscopic Ellipsometry in the ultraviolet spectral region has been implemented in order ...

British Library Electronic Table of Contents (United Kingdom)

In this paper, multilayer oxide nanorods were deposited in the nanopores of anodic aluminum oxide (AAO) via solution infiltration followed by heat treatment. The nanorods have a core-shell structure. First, the shell (nanotube) with the thickness of about 40nm was made of TiO"2 through the hydrolysis of (NH"4)"2TiF"6. Second, silver nanoparticles with the diameter of about 3nm were added into the TiO"2 layer through thermal decomposition of AgNO"3 at elevated temperatures. Then, cylindrical cores (nanorods) of CoO and ZnO with 200nm diameter were prepared, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the structure and composition of the nanorods. UV-vis light absorption measurements in the wavelength range from 350 to...

Energy Technology Data Exchange (ETDEWEB)

In situ scanning tunneling microscopy has been used to study the nucleation and growth mechanisms and the structure of passive films formed on Cu(111) surfaces in 0.1 M borate buffer solution (pH 9.3). A surface topography characterized by terraces with monoatomic steps is obtained after potentiodynamic reduction down to {minus}1.12 V/standard hydrogen electrode (SHE), of the electropolished surface exposed to air. The formation of a single Cu{sub 2}O passive layer at 0.03 V/SHE proceeds first by a roughening of the steps assigned to a locally blocked step flow process due to a competition between dissolution and preferential nucleation of the oxide at the steps. The observed oxide nuclei are 2--3 nm wide and about one atomic plane high. This process leads to the complete coverage of the terraces by a grain-like structure of the oxide film. The initial terrace topography is completely altered. ...

Energy Technology Data Exchange (ETDEWEB)

Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions.

Energy Technology Data Exchange (ETDEWEB)

Samples from a burning bituminous coal seam from Coalspur, Alberta, were studied by reflected light microscopy. Two zones - namely oxidation- combustion and distillation - were detected in the seam. Near the surface, the oxidation zone contained chars showing cracks and oxidation rims. The cracks were filled with fluorescing hydrocarbon material formed by thermal cracking of coal macerals. The chars in the deeper part of the oxidation zone had a carbonized matrix and burnt rims. The distillation zone covered most of the coal seam. Chars were mostly in the precarbonization stage, except those immediately below the combustion zone or near the base of the seam. Precarbonized chars contained pyrolytic carbon in some horizons. The distilled chars were formed by heat generated by combustion at the top of the seam and also by heat transfer from an underlying burning seam through an intermediate clastic ...

Energy Technology Data Exchange (ETDEWEB)

Surface oxide films were grown on 99.99% copper and brass (copper-zinc alloy, Cu77Zn21Al2) in 0.1 mol L{sup -1} borax solution at open circuit potential and were characterized using various experimental techniques. The composition of the passive films formed in situ on the different materials was studied using differential reflectance spectroscopy. The thickness of the oxide layers on copper and brass was compared by chronopotentiometric curves and potentiodynamic reductions. The electrical properties of each oxide were analyzed by means of electrochemical impedance spectroscopy. Their influence on the oxygen reduction reaction was also investigated using voltammetry hydrodynamic tools such as the rotating disk electrode. The results show that the incorporation of Zn to Cu in brass changes the composition and the thickness of the surface film. The films grown on brass tend to be thicker but less ...

Energy Technology Data Exchange (ETDEWEB)

The reactions between (100) GaAs and the near-noble metals Ni, Pd, and Pt have been investigated by application of high-resolution transmission electron microscopy (TEM), energy-dispersive analysis of x rays in the scanning TEM and Rutherford backscattering spectrometry. Emphasis is placed on the evolution of the phase distributions, film compositions, and interface morphologies during annealing at temperatures up to 480 /sup 0/C. The first phase in the Ni/GaAs reaction is shown to have the nominal composition Ni/sub 3/GaAs. Ternary phases of the type Pd/sub x/GaAs are also found to be the dominant products of the Pd/GaAs reaction. Conversely, only binary phases result from the Pt/GaAs reaction. These observations are used to construct isothermal sections of the M--Ga--As thin-film phase diagrams. The behavior of a thin (1--2 nm) native oxide--hydrocarbon layer during the Ni/GaAs, Pd/GaAs, and Pt/GaAs reactions is also investigated. Only the ...

Energy Technology Data Exchange (ETDEWEB)

Maximum metal loss rate of Alloy 800 coupons was about 0.5 mil/year and occurred at the maximum temperature of 600/sup 0/C. Significantly greater oxide penetration into the alloy occurred in unabraded as-received tubing. Since the corrosion rate of unabraded tubing was less temperature sensitive than polished coupons, and attained a maximum value at temperatures in the range of 550 to 565/sup 0/C, a value of 1 mil/year should be used as the corrosion rate for design purposes. Because daily thermal cycling is inherent in solar central receiver operation, oxidation and chromium depletion rates can be expected to increase if surface oxide layers spall. The oxide layers formed on Alloy 800 appeared to be adherent, and adherence will benefit further from growth-derived compressive stresses in oxide layers on the salt-exposed ...

International Nuclear Information System (INIS)

Alloy 800 and Alloy 600 are well known for their resistance to corrosion in an aqueous medium at high pressure and temperature, for which they have been widely used for more than 3 decades in different structural components of water refrigerated nuclear reactors, especially as material for the steam generator tubes (SG) in these nuclear plants. The SG tubes in the Atucha I and Embalse Nuclear Plants are made with Alloy 800. The speed of corrosion of these materials in a reactor's refrigerant medium, while very small is perfectly measurable and can be described by parabolic or logarithmic type kinetics. In other words this speed is high in the first states of growth during the formation of a protective oxide film but then drops to almost stationary values. One characteristic of these films is the formation of a double layer (or duplex): i) an internal adhering layer, of approximately constant thickness, formed by small ...

Energy Technology Data Exchange (ETDEWEB)

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni-Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr{sub 2}N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr-nitride surface layer was found to be the initial formation of oxide during nitridation, ...

Energy Technology Data Exchange (ETDEWEB)

One of the main problems facing the mining sector is the production of acid mine drainage (AMD), which is caused by the oxidation of sulphide minerals in the presence of water. AMD can have a detrimental effect on the environment. One solution is to use soil covering over the materials that cause acid to limit the gas flux by diffusion. A capillary barrier effect is generated by using various layers of different types of soil. In the composite system till and clay normally form the basis of the fine material layer. The use of low sulphide tailings to replace the use of fine grained soil was studied to evaluate its effectiveness. Following both in situ and laboratory experiments spread over an eight-year period, the results indicated that an effective method to limit the oxygen flux and generation of AMD is the use of non-acid generating tailings as the moisture retaining layer. The main concepts that ...

Energy Technology Data Exchange (ETDEWEB)

Studies were conducted of the bifunctional oxygen electrode. The development of a rechargeable metal-oxygen (air) cell has been hampered to a great extent by the lack of a stable and cost effective oxygen electrode capable of use during both charge and discharge. The first type of bifunctional electrode consists of two distinct catalytifc layers. The oxygen reduction catalyst layer containing a supported gold catalyst is in contact with a hydrophilic nickel layer in which evolution of oxygen takes place. Loadings of gold from 0.5 to 1.0 mg/cm/sup 2/ were investigated; carbon, graphite, metal, and spinel oxides were evaluated as substrates. The second part of the research effort was centered on developing a reversible oxygen electrode containing only one catalytic layer for both reduction and evolution of oxygen. The work was directed specifically to the study of perovskite type of ...

International Nuclear Information System (INIS)

The potentiodynamic polarization measurement of 254SMO stainless steel (UNS 31254) was conducted in 3.5% NaCl solutions with pH ranging from 0.1 to 5. The results indicated that this stainless steel offered excellent pitting corrosion resistance in corrosive environments. Further, it also exhibited various features on the polarization curves in different pH solutions. The electrochemical constant-potential passivation treatment performed at different pH followed by XPS analysis revealed that the primary constituents of the outermost layer of the passive films formed in the weak (pH 5) and strong (pH 0.8) acid solutions are iron oxides and Cr_2O_3 and Cr(OH)_3, respectively. Molybdenum oxides, primarily in the six-valence state, existed in the outermost layer of the passive film. Only very weak signals corresponding to that of nickel oxides were detected in the film formed in the ...

CERN Document Server

565 deg C occurs when dissolution rate exceeds oxidation rate, exposing the fresh Al anode to the glass melt. Under inert atmosphere (at 583 deg C), air oxidation is not possible and galvanic cell redox reactions generate an excessive copper interlayer as the system attempts to sustain the oxide layer at the anode. Similar behaviour is observed in those coatings formed on the alloy using glass C (containing Al sub 2 O sub 3 and Na sub 2 O). In this case, the interfacial reactions involve the PbO of the glass and Pb-rich spherical precipitates are formed in the interfacial region, along side sodium aluminosilicate phases, precipitated from the PbO-depleted glass. The behaviour in both systems indicates that oxygen diffuses through the edge of the glass drop, from the atmosphere, to the substrate/glass interface. Coatings formed on the MMCs in air exhibited a porosity of approx 10%, attributed to the ...

Energy Technology Data Exchange (ETDEWEB)

Aluminium AA5182 coupons covered by a polyaniline film in the emeraldine base (EB) form showed increasing corrosion potential and decreasing corrosion current as a function of the thickness of the polymer layer. The cathodic reaction was proved not limited by diffusion of species inside the electrolyte solution and oxygen had no effect on the electrochemical behaviour of the coated samples. An EB coating on indium tin oxide conducting layer appeared slightly electroactive in neutral media. The IR spectra of aluminium coated samples, before and after heating in argon atmosphere, confirmed a redox reaction between the polymer film and the metal. This galvanic coupling can explain the good protective behaviour of emeraldine base against corrosion of aluminium.

British Library Electronic Table of Contents (United Kingdom)

The electroless nickel plating/poly(dl-lactide-co-glycolide) composite coating (EN-plating/PLGA composite coating) was fabricated on the surface of the micro-arc oxidation (MAO) film of the magnesium alloy AZ81 to double control the corrosion and drug release in the hanks' solution. The EN-plating was fabricated on the MAO coating to improve the corrosion resistance by overlaying most pores and micro-cracks on the surface of the MAO film. Meanwhile, a double layered organic poly(dl-lactide-co-glycolide)/paclitaxel (PLGA/PTX) drug releasing coating with a top layered PLGA drug controlled releasing coating on EN plating was prepared to control the drug release rate by adjusting the different lactide: glycolide (LA:GA) ratio of PLGA. Scanning electron microscopy (SEM) and the X-ray powder dif...

International Nuclear Information System (INIS)

Complimentary spectroscopic, microscopic and electrochemical studies were performed to characterise the barrier properties as well as the interface structure of model iron substrates covered with thin plasma polymer films. Cathodic plasma polymers were deposited which show high barrier properties. The metal surface was pre-treated by a reducing or oxidising plasma. This allowed the adjustment of the oxidation state of the interface layer. The interface structure was characterised by means of X-ray photoelectron sputter profiles, infrared spectroscopy and the application of a Kelvin probe. The investigations show that the measured Voltapotential on the plasma polymer surface can be correlated with the oxidation state of the interface. Reducing plasmas lead to an almost oxide free surface. After deposition of the plasma polymer, this reduced state of the oxide is sensitive to ...

International Nuclear Information System (INIS)

Plasma-deposited thin films prepared at room temperature, ranging from 46 to 250 A of PdAu on #approx#45-50 A Si-oxide and Si-oxynitride films grown on Si wafers were studied. Grazing incidence X-ray diffraction, X-ray reflectivity, and XPS depth profile techniques were used to characterize the thin films. A reactive interface involving Pd- and Au-silicides is formed, linking the thin film to the Si-oxide and Si-oxynitride films: a small fraction of Pd and Au atoms from PdAu migrate into the Si substrate, first penetrating the oxide layer, and the small fraction of Si atoms from the oxide layer migrate into the PdAu film and form a silicide interlayer consisting of a reactive interface made up of mixtures of Au- and Pd-silicides interspersed within the matrix of PdAu and substrate. The concentration profiles of these silicides have a maximum at the interface ...

Energy Technology Data Exchange (ETDEWEB)

Extensive experimental investigation has been carried out on used flight bearings of the high pressure oxidizer turbopumps (HPOTP) of the space shuttle main engine (SSME) in order to determine the dominant wear modes, their extent, and causes. The paper presents the methodology, various surface analysis techniques used, results, and discussion. The mode largely responsible for premature bearing wear has been identified as adhesive/shear peeling of the upper layers of bearing balls and rings. This mode relies upon the mechanisms of scale formation, breakdown, and removal, all of which are greatly enhanced by the heavy oxidation environment of the HPOTP. Major causes of the high wear rates appear to be lubrication and cooling, both inadequate for the imposed conditions of operation. Numerous illustrations and evidence are provided. 22 refs.

International Nuclear Information System (INIS)

Yttria stabilized zirconia (YSZ) with 8 mol% Y was deposited by reactive magnetron sputtering onto oxidized (100) silicon substrates. It was possible to switch film texture from (111) to (200) by applying a strong RF substrate bias. Transmission electron microscopy showed that the film deposited under bias is porous and exhibits nanoscaled grains, whereas the film deposited without bias is dense and columnar. The ionic conductivity as a function of temperature revealed an activation energy of 1.04 eV. The mechanical stress could be tuned to low values by thermal post-annealing. Using the dense (111) film as electrolyte layer, and the porous (200) film as an interlayer to a porous Pt anode, an open circuit voltage of 0.85 V was obtained in a micro machined fuel cell structure.

British Library Electronic Table of Contents (United Kingdom)

Ceramic coatings with high emission were fabricated on Ti6Al4V alloy by microarc oxidation (MAO) with additive FeSO4 into the electrolyte. The microstructure, chemical composition and chemical state of the coatings were determined by SEM, XRD, EDS and XPS, respectively. The bonding strength between the coating and substrate was studied by tensile strength test, together with the thermal shock resistance of the coating. The results showed that Fe content in the coating layer significantly affect its thermal emissivity. The relative content of Fe in the coatings surface increased at first and then decreased with increasing the concentration of FeSO4 in electrolytes, so does the emissivity of the coatings. The bonding strength became weaker with increasing the concentration of FeSO4. In addit...

Science.gov (United States)

Data are presented on the continuous-wave (cw), room-temperature (300 K) operation of stripe-geometry In{sub 0.5}(Al{sub {ital x}}Ga{sub 1{minus}{ital x}}){sub 0.5}P quantum-well heterostructure lasers defined via hydrogenation. Passivation of the Zn acceptors in the cap and upper confining layer provides gain guiding, and elimination of the current-blocking oxide reduces the thermal impedance. The resultant device is capable of better performance than conventional oxide-stripe diodes fabricated on the same material.

Energy Technology Data Exchange (ETDEWEB)

The deterioration of AA2024, AA6061 and AA7475 anodised in an environmentally-compliant tartaric acid/sulphuric acid electrolyte has been examined as a function of the immersion time in the electrolyte after termination of anodising. By transmission electron microscopy and scanning electron microscopy, degradation of the porous oxide film was qualitatively observed on AA2024. Electrochemical impedance spectroscopy revealed that AA2024 and AA7075 were more sensitive to prolonged immersion in the anodising electrolyte compared with AA6061, due to increased barrier layer thinning rates and increased susceptibility to localized corrosion. Salt spray tests confirmed the previous, indicating decay of anticorrosion performance for AA2024 and AA7075.

Energy Technology Data Exchange (ETDEWEB)

The goal of the present work has been to clarify the influence of sulphate ions on the oxide films formed on stainless steel and Ni-based alloys in simulated crack chemistry conditions using different ex situ analytical techniques. The main observations of this work can be summarised as follows: The thickness of the films formed in simulated oxygen-free crack chemistry conditions during an exposure of circa 4 days varies roughly in the range 200..500 nm, which corresponds to observations reported in the literature [2]. The presence of 10000 ppb sulphate ions in simulated crack tip conditions seems to lead to a considerably lower thickness of the oxide films when compared to sulphate-free conditions. The presence of 10000 ppb sulphate ions leads also to considerable changes in the morphology of the oxide crystals on the material samples. In the absence of sulphate the outer oxide ...

International Nuclear Information System (INIS)

Recent nuclear power plants require high purity water to protect nuclear reactors or steam generators from SCC and maintain in good condition. In this connection, it is especially important to minimize sulfate, which is a corrosive chemical originated from oxidative degradation of cation exchange resins during operation. Recently, uniform particle size (UPS) strong acid cation gel resin with 14% cross-linkage, which has excellent stability against oxidization, has been applied to several condensate purification systems. For further improvement of water quality, some methods for changing the configuration of condensate demineralizer's resin bed have been examined. For example, these methods correspond to anion under layer and cation over layer. We have tested these methods by cold column tests. Furthermore, we have developed the newly anion exchange resin having higher efficiency and capacity for ...

International Nuclear Information System (INIS)

Modelization of crack propagation and theoretical prediction of rupture are the two main objectives of researchers in stress corrosion cracking. Nevertheless, to reach this aim, the behavior of the passive film which appears spontaneously on the substrate in contact with an environment has to be known. This structural and mechanical characterization is all the more difficult because the number of parameters is important: crystallinity rate, defects concentration, thickness (about a few nanometers), electric field, chemical composition (a lot of oxides are present), peeling layers (atomic structure for example) and some hypothesis can be made about their multi-layer structure, their chemical composition or their epitaxial character... Passive films formed on 316L or 304L stainless steels in different aqueous solutions (in ambient air, in MgCl_2 at 117 deg. C...) have been studied and some important remarks about their ...

International Nuclear Information System (INIS)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after electrochemical surface nitriding, a technique proven to have an effect analogous to N alloying. It was shown that nitrogen, nickel and molybdenum additions independently and in certain combinations stimulate selective dissolution of iron, resulting in a significant enrichment of chromium beneath the passive film. ...

Energy Technology Data Exchange (ETDEWEB)

The effects of {alpha} particle irradiation on a passive film formed on a 304 type stainless steel are studied in situ. The experimental arrangement minimizes the radiolysis effects due to the electrolyte. Under irradiation, a modification of the electronic structure of the oxide layers is revealed by photo-electrochemistry and impedance measurements. The influence of irradiation on the corrosion resistance of the passive film is investigated. Comparing the rest potential and the breakdown potential respectively under and without irradiation, a drop in the passivity range under irradiation is shown. this is interpreted as a decrease in the corrosion resistance. (author).

Science.gov (United States)

Mild steel samples were studied by chronoamperometry in sodium sulfide (Na[sub 2]S) aqueous solution. Pit nucleation and growth also were monitored by optical microscopy. The influence of variables such as temperature, polarization potential, surface roughness, the presence of electrochemically generated oxide layers, and the simultaneous presence of potassium hydroxide (KOH) was studied. The influence of each parameter on pit shape and growth was reviewed. Different reactions and competitive processes were proposed based on the experimental results.

International Nuclear Information System (INIS)

Repassivation resulting from the bared metal surface is a critical process for judging whether or not material suffers from corroding or immunizing. Nickel based alloys with high chromium content were developed to increase the corrosion resistant to sulphur compounds. Active humps resulting from active dissolution of nickel were obtained by creating the bared metal surfaces in thiosulphate solutions. The lower the Cr content the higher is the dissolution rate. The passive films formed on the bared metal surface were examined by ac impedance. Results suggest the formation of multi-layers oxide which were affected by active dissolution reactions during repassivation. (author).

International Nuclear Information System (INIS)

It is very well known that the CANDU reactor has positive Coolant Void Reactivity (CVR), which is most important criticisms about CANDU. The most recent innovations based on using a thin absorbent Hafnium shell in the central bundle element were successfully been applied to the Advanced CANDU Reactor (ACR) project. The paper's objective is to analyze elementary lattice cell effects in applying such methods to reduce the CVR. Three basic fuel designs in their corresponding geometries were chosen to be compared: the ACR-1000TM, the RU-43 (developed in INR Pitesti) and the standard CANDU fuel. The bundle geometry influence on void effect was also evaluated. The WIMS calculations proved the Hafnium absorber suitability (in the latest 'shell design') to achieve the negative CVR target with great accuracy for the ACR-1000 fuel bundle design than for the other two projects. (authors)

International Nuclear Information System (INIS)

There is an increasing interest in using radioisotopes of rare earth elements for internal radiotherapy and for imaging in nuclear medicine. "1"7"7Lu is one of the promising radionuclides. This article reports on the first measurements of the excitation function for the production of "1"7"7Lu with proton-beam energies up to 17 MeV on natural hafnium targets. The experimental cross sections for the reaction "n"a"tHf(p,x)"1"7"7Lu were obtained by the activation of a stacked-foil target and subsequent gamma spectrometry. Theoretical cross sections were calculated up to 35 MeV with the EMPIRE nuclear reaction model code. The measured and calculated cross sections were used for deriving the thick-target yields and for estimating the production of other nuclides than "1"7"7Lu. Measured production cross sections of "1"7"5","1"7"6","1"7"7","1"7"8Ta on the same target are also presented.

Energy Technology Data Exchange (ETDEWEB)

High voltage cathode materials Li-excess layered oxide compounds Li[Ni{sub x}Li{sub 1/3-2x/3}Mn{sub 2/3-x/3}]O{sub 2} (0 < x < 1/2) are investigated in a joint study combining both computational and experimental methods. The bulk and surface structures of pristine and cycled samples of Li[Ni{sub 1/5}Li{sub 1/5}Mn{sub 3/5}]O{sub 2} are characterized by synchrotron X-Ray diffraction together with aberration corrected Scanning Transmission Electron Microscopy (a-S/TEM). Electron Energy Loss Spectroscopy (EELS) is carried out to investigate the surface changes of the samples before/after electrochemical cycling. Combining first principles computational investigation with our experimental observations, a detailed lithium de-intercalation mechanism is proposed for this family of Li-excess layered oxides. The most striking characteristics in these high voltage high energy density cathode ...

Energy Technology Data Exchange (ETDEWEB)

The corrosion behavior of 304 stainless steel was characterized with cyclic voltammetry in a eutectic Li/K and Li/Na carbonate melt under anode and cathode gas of the molten-carbonate fuel cell (MCFC). The corrosion rate of 304 steel was determined in four different environments of the MCFC with electrochemical methods and from cross-sectional analysis of corrosion layers. These four environments were open-circuit and MCFC-load conditions both under anode and cathode gas. At open-circuit conditions corrosion was more severe under the oxidizing cathode gas then under the reducing anode gas. On the contrary, at load conditions corrosion was more severe under anode than under cathode gas. The anodic polarization under anode gas enhances corrosion, whereas the high anodic polarization under cathode gas leads to anodic protection. Corrosion currents were measured with chronoamperometry and determined with Tafel extrapolation from quasi-stationary ...

Energy Technology Data Exchange (ETDEWEB)

Nitrogen has been added to stainless steels to improve mechanical strength and corrosion resistance. High nitrogen steel production is limited by high gas pressure requirements and low nitrogen solubility in the melt. One way to overcome this limitation is the addition of nitrogen in solid state because of its higher solubility in austenite. However, gas and salt bath nitriding have been done at temperatures around 550 C, where nitrogen solubility in the steel is still very low. High temperature nitriding has been, thus proposed to increase nitrogen contents in the steel but the presence of oxide layers on top of the steel is a barrier to nitrogen intake. In this paper a modified plasma nitriding process is proposed. The first step of this process is a hydrogen plasma sputtering for oxide removal, exposing active steel surface improving nitrogen pickup. This is followed by a nitriding step where high nitrogen contents are ...

Energy Technology Data Exchange (ETDEWEB)

In order to fabricate high temperature superconducting tapes for power applications, the authors have analyzed different buffer layer architectures grown on textured Ni substrates suitable for YBCO deposition. Due to its optimal lattice matching the studied structures present as top layer a CeO{sub 2} film. The deposition of CeO{sub 2} on Ni substrates was performed by pulsed laser ablation and by e-beam evaporation at different temperatures. The films obtained by the two deposition techniques have not optimal structural properties, having a polycrystalline component. The misorientation of CeO{sub 2} is probably due to the formation of NiO at the interface between the film and the substrate during the deposition process even if no oxygen is introduced. In order to prevent Ni oxidation an intermediate 2000 {angstrom} Pd thick film was deposited by e-beam. Furthermore, the lattice mismatch between Pd and CeO{sub 2} is smaller ...

International Nuclear Information System (INIS)

Experimental excitation functions for deuteron-induced reactions up to 20 MeV on high purity natural hafnium were measured with the activation method using a stacked foil irradiation technique. Metallic hafnium foils with thickness of 10 #mu#m were stacked together with 50 #mu#m thick aluminium and 12 #mu#m thick titanium foils. The aluminium foils served as energy absorber while the titanium foils were used to monitor the energy and intensity of the bombarding deuteron beam. From a detailed remeasurement of the complete excitation function of the "n"a"tTi(d,x)"4"8V monitor reaction it was possible to adopt the proper incident energy and beam intensity by comparing the results with the recommended values. High resolution off-line gamma-ray spectrometry was applied to assess the activity of each foil. From the measured activity independent and/or cumulative elemental or isotopic cross section data for production of Ta, Hf and Lu radioisotopes by ...

Energy Technology Data Exchange (ETDEWEB)

Cementitious materials provide an ideal geochemical environment (e.g., high pH pore fluids and large surface areas for sorption) for immobilizing nuclear waste. The inclusion of reducing agents, such as blast furnace slag (BFS) can immobilize radionuclides by forming of solid sulfide phases. Thermodynamic calculations using the MINTEQ geochemical computer code indicate the elemental sulfur present in BPS reacts with the highly mobile pertechnetate anion (TcO{sub 4}{sup -}) anion to form an insoluble technetium sulfide phase (Tc{sub 2}S{sub 7(s)}). Initially, the waste form very effectively immobilizes technetium. However, as oxygen diffuses into the waste form, an outer zone of oxidized concrete and a shrinking core of reduced intact concrete develops. Oxidation of sulfur in the outer zone results in increased technetium concentrations in the pore fluid because Tc{sub 2}S{sub 7(a)} oxidizes to the mobile TcO{sub 4}{sup -} ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than ...

Energy Technology Data Exchange (ETDEWEB)

Chemical looping combustion (CLC) of simulated coal-derived synthesis gas was conducted with NiO oxygen carriers supported on SiO2, ZrO2, TiO2, and sepiolite. The effect of H2S on the performance of these samples for the CLC process was also evaluated. Five-cycle thermogravimetric analysis (TGA) tests at 800 C indicated that all oxygen carriers had a stable performance at 800 C, except NiO/SiO2. Full reduction/oxidation reactions of the oxygen carrier were obtained during the five-cycle test. It was found that support had a significant effect on reaction performance of NiO both in reduction and oxidation rates. The reduction reaction was significantly faster than the oxidation reaction for all oxygen carriers, while the oxidation reaction is fairly slow due to oxygen diffusion on NiO layers. The reaction profile was greatly affected by the presence of H2S, but there was no effect on ...

CERN Document Server

Surface compositional changes in GaAs due to RF plasmas of different gases have been investigated by XPS and etch rates were measured using AFM. Angular Resolved XPS (ARXPS) was also employed for depth analysis of the composition of the surface layers. An important role in this study was determination of oxide thickness using XPS data. The study of surface - plasma interaction was undertaken by correlating results of surface analysis with plasma diagnosis. Different experiments were designed to accurately measure the BEs associated with the Ga 3d, Ga 2p sub 3 sub / sub 2 and LMM peaks using XPS analysis and propose identification in terms of the oxides of GaAs. Along with GaAs wafers, some reference compounds such as metallic Ga and Ga sub 2 O sub 3 powder were used. A separate study aiming the identification of the GaAs surface oxides formed on the GaAs surface during and after plasma processing was ...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited...

Science.gov (United States)

The x-ray diffraction technique described previously for measurement of growth kinetics of Pd/sub 2/Si layers from their solid state reaction couples has been extended by the use of a one-dimensional position-sensitive detector (PSD). Additionally, the method has been extended to include measurement of the Pd layer. A detailed description of the experimental arrangement and analytical procedures is presented. The kinetics of epitaxial Pd/sub 2/Si film growth were measured in situ over a range of 170--230 /sup 0/C. The PSD results, using data obtained from both the Pd/sub 2/Si and Pd layers, were able to confirm parabolic growth behavior for the Pd/sub 2/Si film. The rate constants followed Arrhenius behavior and yielded an activation energy of E = 1.32 +- 0.07 eV with a prefactor k/sub 0/ = 0.49 cm/sup 2//s for the Pd/sub 2/Si layer analysis and E = 1.34 +- 0.17 eV with a prefactor of 0.72 cm/sup 2//s ...

International Nuclear Information System (INIS)

For the advanced fusion reactor FFHR2 (Force Free Helical Reactor) that has been proposed by NIFS, molten salt Flibe (LiF:BeF2=64:36) breeder blanket system is selected because of Flibe's features such as chemical stability, low-pressure operation and low electric conductivity. The Flibe is however high Prandtl number fluid since it has high viscosity and low thermal conductivity. Therefore its heat transfer performance is low compared with liquid Li or Pb-Li. In addition to heat removal of 1MW/m2 on the first wall, electrolysis of molten salt due to MHD effect will take place under high flow rate condition. This indicates that heat transfer enhancement under low flow rate is essential for the Flibe blanket system. In our laboratory, heat transfer characteristics of molten salt HTS (KNO3:NaNO2:NaNO3=53:40:7), have been evaluated, which is used as a simulant fluid of Flibe from the points of view of Be's toxicity and similar Prandtl number. In this paper, we adopt nano-particle ...

UK PubMed Central (United Kingdom)

The tegument of tapeworms is known to be composed of an outer syncytial cytoplasm layer which includes microtriches and cytoplasmic organelles (= syncytial layer), and a parenchymatous cytoplasm layer...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Samples of alloy 800 H (LJNS N08810) and alloy 617 (UNS N06617) were oxidized in a simulated process gas atmosphere. The principal elements of the gaseous environment were 50% H{sub 2}O, 35% H{sub 2} and 5% of CO{sub 2}, CO, and CH{sub 4}, respectively. The experiments were carried out at temperatures from 850 C to 950 C for exposures ranging from 600 to 5,000 hours. After the exposure, the alloy surfaces showed compact oxide layers, which resulted in a depleted zone of oxidizing elements in the substrate layer. Using Electron Probe Microanalysis (EPMA), concentration profiles and the extension of the depleted zone were measured. Calculated theoretical profiles were then fitted to the EPMA-measured profiles, using Fick`s second law of diffusion and resolved by a finite difference method and diffusion coefficients as fitting parameters. The diffusion coefficients for chromium may be ...

Energy Technology Data Exchange (ETDEWEB)

We report on studies of device degradation in organic photovoltaic devices based on blends of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester (PCBM). Since delamination, oxidation, and chemical interactions at the metal electrode/organic interface have long been posited as degradation pathways in organic electronic devices, we first investigated the stability of a variety of electrodes for devices stored in an inert, dark environment. Second, a set of experiments was designed to separate the effects at the metal/organic interface from the degradation of the active layer or the hole extraction interface. To do this, Ca/Al electrodes were deposited to complete half of a substrate's devices, and samples were left both under constant illumination and 10% illumination (10% duty cycle of 1 sun illumination) in a glovebox environment. After more than 200 h of measurement, additional electrodes were deposited and ...

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl solution with a carrier density two ...

Science.gov (United States)

The strain dependence of Si-Ge interdiffusion in epitaxial Si/Si{sub 1-y}Ge{sub y}/Si heterostructures on relaxed Si{sub 1-x}Ge{sub x} substrates has been studied using secondary ion mass spectrometry, Raman spectroscopy, and simulations. At 800 and 880 deg. C, significantly enhanced Si-Ge interdiffusion is observed in Si/Si{sub 1-y}Ge{sub y}/Si heterostructures (y=0.56, 0.45, and 0.3) with Si{sub 1-y}Ge{sub y} layers under compressive strain of -1%, compared to those under no strain. In contrast, tensile strain of 1% in Si{sub 0.70}Ge{sub 0.30} layer has no observable effect on interdiffusion in Si/Si{sub 0.70}Ge{sub 0.30}/Si heterostructures. These results are relevant to the device and process design of high mobility dual channel and heterostructure-on-insulator metal oxide semiconductor field effect transistors.

Energy Technology Data Exchange (ETDEWEB)

Pitting behavior of alloy 800 was investigated as a function of temperature and prefilming in high-temperature water. The behavior was characterized in terms of pitting potential (U{sub p}) and pit density (n{sub p}). U{sub p} decreased with increasing temperature and chloride activity. Prefilming of test coupons over a period between 100 h and 5,000 h in ammoniated water at 300 C had no apparent influence on U{sub p} at room temperature, 180 C, and 300 C. However, the number of pits in prefilmed coupons was much higher than in coupons covered with an air passive layer. The effect of prefilming on pit nucleation was investigated in detail with regard to a model and test methods developed by Bianchi, et al. Density of pits in prefilmed coupons was at least 1 order of magnitude higher than in air passive coupons. Maximum pit density was measured after a prefilming period of 100 h. The effect was discussed in terms of Bianchi`s model and in terms of features of ...

Energy Technology Data Exchange (ETDEWEB)

Electronic trap densities at the indium tin oxide (ITO)/hole transport layer (HTL) interface in operating organic light-emitting diodes (OLEDs) are characterized in situ using impedance spectroscopy. For OLEDs with a high density of active trap states, negative values of the frequency derivative of resistance are clearly observable for frequencies on the order of 10 kHz, whereas positive values are observed when the trap density is low With this technique, it is revealed that the trap density is minimized via the introduction of a TPD-Si{sub 2} (4,4'-bis[(p-trichlorosilylpropylphenyl) phenylamino]-biphenyl) passivation layer at the ITO/HTL interface or by the application of large electric fields during device operation. Furthermore, impedance spectroscopy illustrates that the ITO/HTL interface is not a simple series resistance when traps are present since they are shown not to contribute to high frequency ...

Energy Technology Data Exchange (ETDEWEB)

In the present paper, the chemical composition of passive films formed on both phases of two types of duplex stainless steels (UNS S31803 and UNS S32304) is determined at the micro-scale using Auger electron spectroscopy (AES). Samples were either mechanically polished (down to diamond pastes) or electrochemically etched in acidic solutions. The micro-electrochemical behavior of samples was then determined in sodium chloride media by means of the electrochemical micro-cell technique (capillary diameters of 30 {mu}m). The results obtained were analyzed considering the passive film chemical composition. Quantitative relationships between electrochemical parameters and the distribution of chromium and iron in the oxide layer were found. Due to differences in mechanical properties between ferrite and austenite, a heterogeneous stress distribution is generated in both phases. A method based on thermal-mechanical simulation was used to quantify ...

International Nuclear Information System (INIS)

The adherent magnetite film thickness, corrosion rate and the loose crud on the surface of carbon steel and other structural materials were evaluated by inserting the coupons in the two autoclaves connected to the two ends of the PHT systems of Indian PHWRs. This paper includes an analysis of the results obtained during the hot conditioning of TAPP-3 and 4, Kaiga-3 and 4, and RAPP-5. The system temperatures of 230 deg C to 260 deg C and the adherent magnetic thickness of 0.30 ?m to 0.75 ?m on the internal surface of carbon steel were achieved during the hot conditioning of these reactors. The time duration of termination of the hot conditioning ranged from 48 to 71 hours. The maximum magnetite film thickness of 0.75 ?m in 71 hours and temperature 260 deg C and a minimum thickness of 0.30 nm in 48 hours at 230 deg C were achieved during hot conditionings. The XRD analyses of hot conditioned carbon steel coupons showed that oxide film constitutes only magnetite. ...

International Nuclear Information System (INIS)

The electrochemical behaviour of passive films formed on one austenitic stainless steel (AISI 304) and one ferritic stainless steel (AISI 446) in solutions with pH between 0.6 and 8.4 was studied by capacitance measurements and photocurrent spectroscopy. Compositional characterization of the passive films was done by X-ray photoelectron spectroscopy. The capacitance increases with decreasing pH. Doping densities evaluated from Mott-Schottky plots are in the range 2-6 x 10"2"0 cm"-"3 and increased with the pH in the neutral/alkaline range while in pH 0.6, values above 10"2"1 cm"-"3 were found. The bandgap energy indicates two transitions, at 2.5-2.8 and 3.2 eV. The analytical data reveal that, as the pH increased, the films become enriched in Fe(II) and Fe(III), whereas the Cr(III) gradually decreases. The films formed at very low pH had a behaviour that contrasts with that of the films formed in the neutral/alkaline media. The films are described by a bilayer structure, with hydroxides ...

Energy Technology Data Exchange (ETDEWEB)

Polymeric coated ferromagnetic carriers with an absorbed layer of octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) diluted by tributyl phosphate (TBP) are being evaluated for application in the separation and the recovery of low concentrations of americium, plutonium, and uranium from nuclear waste solutions. Due to their chemical nature, these extractants selectively complex americium and plutonium contaminants onto the particles and the complexed particles can be recovered from the solution using a magnet. Physical and chemical characterization of the extractant-absorbed particles were performed by gamma and liquid scintillation counting, scanning electron microscopic (SEM) micrograph, and other physical measurements. Plutonium, americium, and uranium separations have been performed at various HNO{sub 3} and HCl concentrations. Parameters were studied to determine the limitations and capacity of the process. The status of the ...

Energy Technology Data Exchange (ETDEWEB)

The authors present the results of their investigation of the effect of phosphorus compounds on the activity of tungsten-containing catalysts in the oxidation of ethane. They investigated tungsten-phosphorus catalysts with different phosphorus concentrations (calculated on the basis of P/sub 2/O/sub 5/). The catalysts were prepared by heat decomposition of the starting compounds at 750/sup 0/C for 4 h. As their starting compounds, they used two types of materials: heteropoly acids mixtures of monosubstituted ammonium phosphoric and tungstic acids. The specific surface area of the catalysts was determined using the nitrogen desorption method. The x-ray phase analysis was carried out using a DRON-1.5 diffractometer. The catalytic activity was determined using the impulse method in a reactor with a vibrofluidized catalyst layer.

British Library Electronic Table of Contents (United Kingdom)

Indium sulfide thin films consisting of porous network of nanoplatelets, have been deposited using chemical bath deposition (CBD) method onto the tin-doped indium oxide (ITO) coated glass substrate. Aqueous solutions of indium sulfate and thioacetamide have been used as indium and sulfur precursors. As a complexing agent, acetic acid was used. The chemically deposited indium sulfide thin films were examined for their structural, surface morphological and optical characterizations. The X-ray diffraction analysis revealed the formation of the cubic b-In2S3 onto the substrate. From scanning electron micrograph, it is observed that the surface of substrate is covered by nanoporous platelets type morphology. The optical studies showed a direct band gap of 2.84eV for indium sulfide platelets. Ph...

Energy Technology Data Exchange (ETDEWEB)

Solar cells and organic electronic devices require an encapsulation to ensure sufficient lifetime. Key parameters of the encapsulation are permeation barrier, UV stability, temperature stability, optical transmission spectra and mechanical stability. The requirements depend very much on the specific application. Many work groups suggest multilayer stacks to meet the permeation requirements. In this paper the permeation barrier properties of the different constituents of such a multilayer stack are characterized. Different layer materials are compared regarding their water vapour and oxygen permeability as well as the influence of process parameters is examined. Finally temperature dependent permeation measurements are used to characterize the permeation mechanisms in the different constituents of the multilayer barrier.

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy UNS N06690 were investigated in simulated crevice chemistries. It was found the role of lead in corrosion processes is strongly dependent on the pH value of the testing solutions. At pH 1.5 the effect of lead is narrowly noticeable; while at pH 12.7, lead has a significant influence on the electrochemical performance of alloy UNS N06690. The lead alters the surface morphologies at both pH and account for higher hydroxide content in the surface film at pH 12.7. The lead incorporation hinders the formation of spinel oxides during the passivation in alkaline solution. Nanoindentation tests indicate a significant lead-induced degradation in the mechanical properties of passive films. The passivation degradation is attributed to detrimental effects of lead via interrupting the dehydration process and hindering the formation of protective layers on the alloy surface.

Energy Technology Data Exchange (ETDEWEB)

A prototype trumpet type nonimaging secondary concentrator has been designed and fabricated for use with the Cummins Power Generation (CPG) 7.5 kW(e) dish-Stirling system and a preliminary set of operating tests has been carried out. The secondary is 26.7 cm (10.5 in.) deep by about 69 cm (27 in.) wide, and has a geometric concentration of 1.7X. The test units were fabricated from polished copper spinnings, overcoated with vapor deposited aluminum and aluminum oxide layers and are water cooled. The basic design considerations are reviewed, the objectives and test procedures for the experiment are summarized and some preliminary results are presented.

Energy Technology Data Exchange (ETDEWEB)

Shaped activated charcoal is modified by 02 and N2 processing for producing coal compounds with higher acidic or basic properties. Nitrated activated charcoal has properties of a weak anionite with a substantially increased ion exchange capacity with an increase in the concentration of the hydrogen ions in the electrolyte and adsorbs iodine ions well from aqueous solutions at a pH of less than 5. A layer of nitrated charcoal is a very effective sorbent in the process of dynamic sorption of iodine anions from acetic solutions of KI. It is also established that the sorption of iodine ions in the activated charcoal modified by 02 occurs in accordance with an ion exchange mechanism (and possibly, selective sorption). This refutes literature data which ascribe the determining participation in the process to the reaction of oxidation of iodides on the surface (Pv) of the coal into free I2.

Energy Technology Data Exchange (ETDEWEB)

Whereas supersaturated aluminum alloys demonstrate enhanced passivity, conventional aluminum alloys spontaneously pit in air-saturated chloride solutions. We have concentrated on three areas: evaluation and characterization of Al-W alloys, which exhibit the best corrosion performance of any alloy system studied to date; characterization of the passive-film structure of Al-Mo alloys; and production and characterization of Al-W and Al-Ta powders, which will be used for compaction into bulk material. Surface analysis of the Al-W passive films formed during polarization show surprising little oxidized solute compared to other alloys. These results indicate that the barrier layer formation and electrostatic repulsion mechanisms used to explain the passivity of other alloys are not involved here. Instead the W may act to stabilize the passive film structure in a way similar to the way molybdenum acts in Al-Mo alloys. That is ...

CERN Document Server

We analyze the impact of trap states in the oxide layer of a superconducting tunnel junctions, on the fluctuation of the Josephson critical current, thus on coherence in superconducting qubits. Two mechanisms are usually considered: the current blockage due to repulsion at the occupied trap states, and the noise from electrons hopping across a trap. We extend previous studies of noninteracting traps to the case where the traps have on-site electron repulsion inside one ballistic channel. The repulsion not only allows the appropriate temperature dependence of 1/f noise, but also is a control to the coupling between the computational qubit and the spurious two-level systems inside the oxide dielectric. We use second order perturbation theory which allows to obtain analytical formulae for the interacting bound states and spectral weights, limited to small and intermediate repulsions. Remarkably, it still reproduces the main ...

International Nuclear Information System (INIS)

Coaxial nanocables with a single-crystalline zinc telluride (ZnTe) nanowire core and an amorphous silicon oxide (SiO_x) shell have been synthesized via a simple one-step chemical vapor deposition (CVD) method on gold-decorated silicon substrates. The single-crystal ZnTe nanowire core is in zinc-blende structure along the [111] direction, while the uniform SiO_x shell fully covers the core with no observable pin-hole or crack. Formation mechanisms of the ZnTe-SiO_x nanocables are discussed. The ZnTe nanowire core shows p-type electrical properties while the SiO_x shell acts as an effective insulating layer. The ZnTe-SiO_x nanocables may have potential applications in nanoscale devices, such as p-type FETs and nanosensors.

International Nuclear Information System (INIS)

As part of a study into the properties of ferroelectric single crystals at nanoscale dimensions, the effects that focused ion beam (FIB) processing can have, in terms of structural damage and ion implantation, on perovskite oxide materials has been examined, and a post-processing procedure developed to remove such effects. Single crystal material of the perovskite ferroelectric barium titanate (BaTiO_3) has been patterned into thin film lamellae structures using a FIB microscope. Previous work had shown that FIB patterning induced gallium impregnation and associated creation of amorphous layers in a surface region of the single crystal material some 20 nm thick, but that both recrystallization and expulsion of gallium could be achieved through thermal annealing in air. Here we confirm this observation, but find that thermally induced gallium expulsion is associated with the formation of gallium-rich platelets on the surface of the annealed ...

International Nuclear Information System (INIS)

The disruption of primary innate immune function of the epidermal layer of the skin accounts for the susceptibility of individuals using bleaching agents to localized or systemic infections. This subverted innate immunity in these people may lead to other pathological conditions. The resultant effects of skin bleaching and phagocytes activation in response to infections have not been studied in Nigerians using bleaching agents. The present study therefore assessed the levels of C-reactive protein (CRP), albumin, total antioxidant potential (TAP), total plasma peroxides (TPP), oxidative stress index (OSI) and malonaldehyde (MDA) in the users bleaching agents. Thirty (30) people who had used bleaching agents for average of 4.9 + 1.2 years participated in this study. They were recruited from various schools and markets within the city of Ibadan, Oyo State, Nigeria. Thirty apparently healthy staffs of University College Hospital Ibadan, Ibaadan, ...

Energy Technology Data Exchange (ETDEWEB)

This journal contains the following articles (1) The Grand Challenge of Thermonuclear Ignition--Commentary by Edward I. Moses; (2) Orchestrating the World's Most Powerful Laser--The computer control system for the National Ignition Facility will soon have about 1.4-million lines of code running on more than 750 computers; (3) A Randon Walk through Time and Space--Albert einstein's 1905 papers on Brownian motion, random fluctuations, and statistical mechanics are fundamental to many Livermore research projects; (4) The Search for Methane in Earth's Mantle--Scientists are discovering that Earth's mantle may have untapped reserves of methane; and (5) Testing the Physics of Nuclear Isomers--Results from a tri-laboratory project contradict claims of accelerated release of energy from the nuclear isomer hafnium-178.

Energy Technology Data Exchange (ETDEWEB)

A multiple metal oxide sorbent supported on a zeolite of substantially silicon oxide is used for the desulfurization of process gas streams, such as from a coal gasifier, at temperatures in the range of about 1200.degree. to about 1600.degree. F. The sorbent is provided by a mixture of copper oxide and manganese oxide and preferably such a mixture with molybdenum oxide. The manganese oxide and the molybdenum are believed to function as promoters for the reaction of hydrogen sulfide with copper oxide. Also, the manganese oxide inhibits the volatilization of the molybdenum oxide at the higher temperatures.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Austenitic stainless steels (304-type) have been implanted with nitrogen ions in order to investigate the effects of implanted nitrogen on their electrochemical behaviour and on the nature of the passive film formed on the steels in acid (0.5M H_2SO_4). Alloys with two nitrogen doses have been prepared (2.5x10"1"6 and 2x10"1"7 N atoms/cm"2). The implanted alloys have been characterized by "1"5N-NRA (nuclear reaction analysis) and XPS (X-ray photoelectron spectroscopy). Alloy surfaces with well-defined N concentrations were prepared, prior to the electrochemical measurements, by argon-ion sputtering of the implanted material for a fixed time in order to reach a well-defined point on the nitrogen depth profile. The samples were then transferred without exposure to air to an electrochemical cell mounted in an inert gas glove box. The implanted nitrogen modifies the electrochemical behaviour of the alloy. The anodic dissolution in the active state is enhanced, and the current density in ...

International Nuclear Information System (INIS)

Buffer layers with 100% lattice match with YBa2Cu3O7 - ? (YBCO) were prepared from mixed rare-earth-oxides applying a simple sol-gel process and dip-coating method. Structural analysis of the sol-gel derived powder by X-ray diffraction revealed that the mixing parameter, which eliminates the lattice mismatch with YBCO, is x = 0.2382, 0.1852, 0.1252, 0.0906, 0.0793 and 0.0395 in (Eu1 - xHox)2O3, (Eu1 - xErx)2O3, (Eu1 - xYbx)2O3, (Gd1 - xHox)2O3, (Gd1 - xYx)2O3 and (Gd1 - xYbx)2O3, respectively. Microstructural investigations were carried out for Gd1.819Ho0.181O3 films epitaxially grown on cube-textured Ni (100) substrates by sol-gel dip-coating process. X-ray diffraction of the buffer showed strong out-of-plane orientation on Ni tape. The (Gd1 - xHox)2O3 (222) pole figure indicated a single cube-on-cube textured structure. The omega and phi scans revealed good out-of-plane and in-plane alne alignments. The full-width at half-maximum values of ...

Energy Technology Data Exchange (ETDEWEB)

The experimental effect investigation programme on Zircaloy-4/air oxidation was pursued and expanded to isothermal specimen exposure and the comparison of the oxidation between the atmospheres Ar/O{sub 2} and air. In close connection with the EC project OPSA, which is meanwhile terminated, the investigation concerned specimen exposure in a thermobalance to flowing atmospheres, namely dry Ar/O{sub 2} of composition 80/20 or synthetic air, respectively. As test parameters the linear heat-up rate was varied in the range 5 to 40 K/min and the ramp or holding temperature between 800 and 1500 C. Mass increase and reaction rate were continuously recorded or evaluated in temperature/time dependence. The oxide scale growth was found to be accompanied by colour changes, crack formation and spalling of layers, as well as by dimensional substrate growth, which are the reasons for the observed kinetic results. The ...

International Nuclear Information System (INIS)

Suspension direct current plasma spraying allows achieving finely structured coatings whose thickness is between few tens and few hundreds of micrometres. Drops (200-300 ?m in diameter) or liquid jets are mechanically injected in the plasma jet. With radial injection they are rapidly (a few ?s) fragmented into droplets (a few ?m in diameter). The latter are vaporized (in a few ?s) and the solid particles contained in suspension droplets are accelerated and melted by the plasma jet. As in conventional plasma spraying (CPS), much smaller splats (with diameters between 0.2 and 3 ?m and thicknesses between 30 and 200 nm) are arranged in layers up to form the coating. The low inertia of particles requires spray distances between 40 and 60 mm which induces plasma heat fluxes up to 22 MW m-2 participating in coating densification. Even more than in CPS, the plasma jet fluctuations, particularly for plasmas containing di-atomic gases, perturb drops penetration and ...

International Nuclear Information System (INIS)

... ammonium compounds benzilic acid chemical preparation lanthanum oxides

International Nuclear Information System (INIS)

This work is concerned with the development and application of ion implantation techniques for improving the corrosion resistance of zircaloy-4. The corrosion resistance in nitrogen implanted zircaloy-4 under a 120 keV nitrogen ion beam at an ion dose of 3 x 10"1"7 cm"-"2 depends on the implantation temperature. The characteristics of surface oxidation and corrosion resistance were analyzed with the change of implantation temperature. It is shown that as implantation temperature rises from 100 to 724 C, the colour of specimen surface changes from its original colour to light yellow at 100 C, golden at 175 C, pink at 300 C, blue at 440 C and dark blue at 550 C. As the implantation temperature goes above 640 C, the colour of surface changes to light black, and the surface becomes a little rough. The corrosion resistance of zircaloy-4 implanted with nitrogen is sensitive to the implantation temperature. The pitting potential of specimens increases from 176 to 900 mV ...

Energy Technology Data Exchange (ETDEWEB)

Isothermal reaction experiments were performed in the temperature range of 1000 - 1300 C in order to determine the chemical interactions between Zircaloy-4 fuel rod cladding and Inconel-718 spacer grids of Pressurized Water Reactors (PWR) under severe accident conditions. It was not possible to apply even higher temperatures since fast and complete liquefaction of the components occurred as a result of eutectic interactions during heatup. The liquid reaction products formed enhance and accelerate the degradation of the material couples and the fuel elements, respectively. Only small amounts of Inconel are necessary to liquefy large amounts of Zircaloy. Thin oxide layers on the Zircaloy surface delay the beginning of the chemical interactions with Inconel but cannot prevent them. In this work the reaction kinetics have been determined for the system: as-received and pre-oxidized Zircaloy-4/Inconel 718. The interactions can ...

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

The performance of four different organic coating systems applied to carbon and weathering steel coupons has been assessed in this investigation. applied on the surface of carbon steel and weathering steel coupons. The coupons have been evaluated using five different tests, three field tests and two accelerated tests. The field tests were carried out at three atmospheric stations, located at COSIPA in Cubatao-SP, at Alto da Serra in Cubatao-SP and at Paula Souza in Sao Paulo city. The accelerated tests consisted of (a) exposure to alternate cycles of ultraviolet radiation/condensation combined with salt spray cycles (UVCON combined with Salt Spray) and of (b) exposure to alternate cycles of ultraviolet radiation/condensation combined with the Prohesion test. The performance of the coatings was assessed by visual observation and photographs, using a method based on ASTM D-610, ASTM D-714 and ASTM-1654 standards to rank them. The oxide phases formed on the surfaces ...

British Library Electronic Table of Contents (United Kingdom)

Layered carbon fiber mats have been prepared by layer-by-layer (LBL) electrospinning of polyacrylonitrile onto thin natural cellulose paper and subsequent carbonization. The layered carbon fiber mat has been proved to be a promising microbial fuel cell anode for high density layered biofilm propagation and high bioelectrocatalytic anodic current density.

International Nuclear Information System (INIS)

Austenitic stainless steels have been implanted with molybdenum ions (Mo"+, 100 keV, 2.5 x 10"1"6 atoms cm"-"2). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of #approx# 1000 A with a maximum molybdenum concentration of #approx# 9 at.% Mo located at #approx# 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H_2SO_4 have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer hydroxide ...

International Nuclear Information System (INIS)

This paper deals with the characterization of passive films formed on stainless steel (26% Cr and 0 to 3%Mo). The influence of the applied passivation potential and the effect of molybdenum additions to steel upon the composition profiles of passive films formed in an aqueous NaCl solution (3.5% at pH 2.5) are studied. The technique involved is Auger electron spectroscopy combined with ion sputtering. Some electrochemical techniques have been used in conjunction. A quantitative approach of the Auger spectra during the progressive removal of the passive film is described. The peak-to-peak height of the Auger lines are treated in order to yield the atomic fraction of the various elements present in a given subsurface layer. The analytical study of the film by electron spectroscopy indicates that molybdenum plays a part at the metal-oxide interface where this element acts on the chromium diffusion process. This phenomenon, which depends on the ...

Energy Technology Data Exchange (ETDEWEB)

Solid-state lithium batteries with a unique construction are reported in this paper. These batteries contain two kinds of lithium ion-conductive solid electrolytes, LiI-Li{sub 2}S-P{sub 2}S{sub 5} glass contacted with the anode material and Li{sub 3}PO{sub 4}-Li{sub 2}S-SiS{sub 2} glass or Li{sub 2}S-GeS{sub 2}-P{sub 2}S{sub 5} crystalline material contacted with the cathode. The former electrolyte was selected as that stable to electrochemical reduction, and the latter two to oxidation. This construction made it possible to use graphite as the anode and LiCoO{sub 2} as the cathode in the solid-state lithium battery. The energy density of the battery is 390 W h{center_dot}l{sup -1} and 160 W h{center_dot}kg{sup -1} per total volume and weight of the cathode and anode layers, respectively, which are comparable to those of commercialized Li-ion batteries.

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on mild steel in aqueous 8.6 mM NaCl solutions (pH 8), containing either MoO{sub 4}{sup 2-} or NO{sub 2}{sup -}, have been studied with X-ray photoelectron spectroscopy. For either anion these films are {approx}5 nm deep, and the primary chemical state of iron is Fe{sup 3+}. Following exposure to MoO{sub 4}{sup 2-}, the film consists of a sub-layer ({approx}4.1 nm) composed largely of ferric oxide/hydroxide, overlaid by Fe{sub 2}(MoO{sub 4}){sub 3} ({approx}0.6 nm). As regards NO{sub 2}{sup -}, spectra are consistent with the film being closely related to {gamma}-Fe{sub 2}O{sub 3}. Furthermore, a reduction product of NO{sub 2}{sup -}, potentially N{sub 2}, is present, displaying a depth profile comparable to that of molybdate.

International Nuclear Information System (INIS)

The diffusion of ion beam injected self-interstitials (I) and their interaction with impurities in crystalline Si has been investigated and modeled. In particular, the I-substitutional carbon (C) interactions have been studied, using a molecular-beam-epitaxy grown Si_1_-_yC_y layer interposed between the shallow I-source and a deeper B-spike (marker for I-concentration). Substitutional C atoms are shown to trap I's, to be removed from their substitutional sites, and to form stable precipitates into the C-rich region. The I-trapping mechanism was quantitatively studied by a simulation code. The reactions causing trapping and deactivation are described. In addition, the boron markers approach was extended to the two dimensional (2D) diffusion. High resolution scanning capacitance microscopy was used for quantitative measurements of the 2D boron transient enhanced diffusion induced on a boron delta array by the I's ion beam injected through a sub-micron dimension ...

International Nuclear Information System (INIS)

Measurements of ion-induced electron emission have been performed with helium and argon ions with energies between 300 and 900 eV on W, W with 10% Ti, Al, Al with 1% Cu, Al with 1% Si, Si, and Be. This article describes many of the important surface characteristics that influence the ion-induced electron emission. For low-energy ions, the substrate material was found to be less important as the velocity of the incident ion decreased. In the case of incident Ar"+ the substrate material had a negligible effect on the emission for this energy range. The presence of an adsorbed layer enhanced emission in all cases. Heating the substrates resulted in oxidation of the surfaces and a subsequent increase in emission. The electron emission from aluminum samples with smaller grain sizes was higher than samples of identical composition with larger grains. This effect is due to the greater number of adsorption sites resulting from the higher grain boundary ...

International Nuclear Information System (INIS)

In this paper, we propose to characterize boron transient enhanced diffusion (TED) for processes currently used for P"+/N ultra-shallow junctions (USJ) fabrication. Indeed, the fundamental understanding of boron diffusion for low energy boron implantation is mandatory to evaluate the scalability of such processes for the coming complementary metal-oxide-semiconductor (CMOS) transistor generations. In these experiments, we characterize the boron anomalous diffusion, thanks to boron buried marker-layers obtained by epitaxial growth. B"+ and BF_2"+ ultra-low energy (ULE) implantations and plasma doping (PLAD) using BF_3 as precursor gas are carried out to compare the two techniques used for advanced USJ fabrication. Boron diffusion behaviors are analyzed via secondary ion mass spectrometry for annealing at 700 deg. C for 5 min and 15 min. Finally this paper brings some physical insights explaining the technological benefit coming from PLAD ...

International Nuclear Information System (INIS)

Research was conducted at Pacific Northwest Laboratory to develop high photosensitivity adaptive optical elements utilizing ion implanted lanthanum-doped lead-zirconate-titanate (PLZT). One centimeter square samples were prepared by implanting ferroelectric and anti-ferroelectric PLZT with a variety of species or combinations of species. These included Ne, O, Ni, Ne/Cr, Ne/Al, Ne/Ni, Ne/O, and Ni/O, at a variety of energies and fluences. An indium-tin oxide (ITO) electrode coating was designed to give a balance of high conductivity and optical transmission at near uv to near ir wavelengths. Samples were characterized for photosensitivity; implanted layer thickness, index of refraction, and density; electrode (ITO) conductivity; and in some cases, residual stress curvature. Thin film anti-ferroelectric PLZT was deposited in a preliminary experiment. The structure was amorphous with x-ray diffraction showing the beginnings of a structure at ...

Energy Technology Data Exchange (ETDEWEB)

The chemical interaction of a Si{sub 3}N{sub 4} ceramic with pristine and oxidised 100Cr6 steel was studied by means of static interaction couple experiments between 500 and 1200 C. Si{sub 3}N{sub 4} was not chemically stable in contact with oxidised steel at elevated temperatures, and reacts with the formation of N{sub 2}, SiO{sub 2} and/or Fe{sub 2}SiO{sub 4} at temperatures at and above 1000 C. At 700 and 500 C, Si diffusion into the oxide layer indicated the dissociation of the Si{sub 3}N{sub 4} ceramic. Si{sub 3}N{sub 4} also dissociated in contact with pristine steel. In the temperature region between 700 and 1100 C, the Si dissolves and diffuses into the steel whereas a nitrogen pressure is built-up in the voids of the metal-ceramic interface, limiting the degree of interaction. Above 1100 C, the nitrogen dissolves and diffuses into the steel as well, enhancing the reactivity and resulting in the formation of a strong metal-ceramic ...

Energy Technology Data Exchange (ETDEWEB)

The role played by calcium sulfite in the flue gas desulfurization of lime/limestone scrubbers makes it desirable to work out its thermodynamic properties. A thermogravimetric apparatus was used to study the equilibria between calcium sulfite hemihydrate and calcium sulfite anhydrite under different conditions. Efforts were made to analyze the difficulties encountered in the dynamic approach to equilibration after calcium sulfate dihydrate failed in calibration of the apparatus. Finally, the kinetics and thermodynamics for the dissociation of calcium sulfite hemihydrate were examined. The confirmation of Engel-Brewer's correlation between the electronic configuration and crystal structure in metallic systems has long been pursued in this group by studying the Lewis-acid-base interactions. Tantalum-iridium alloys of different compositions were brought into equilibrium with various steam/hydrogen mixtures in the same thermogravimetric setup. Although the kinetics is limited by ...

Energy Technology Data Exchange (ETDEWEB)

The interrelationship between the testing temperature and HfC strength increment of an arc-melted W-3.6Re-0.4HfC was determined from 1950 K to 2980 K in a vacuum of better than 1.3{times}10{sup {minus}5} Pa (10{sup {minus}7} torr). The present research was focused on the characteristic temperature at which the rapid coarsening of HfC particles occurred and the effect of the second-phase particle size on the high temperature strength properties of this material. It was found that the HfC particle strengthening was effective in a W-Re matrix up to a characteristic temperature of 2450 K in the short-term tensile test. Carbon was found to be the rate-limiting solute in the HfC particle growth. The strength of HfC strengthened alloy at temperature above 0.5 T{sub m} is proportional to the square root of particle volume fraction. The yield strengths of W-3.6Re-0.26HfC calculated based on the particle statistical distribution had good agreement with the experimental values from 1950 K to 2980 ...

International Nuclear Information System (INIS)

The influence of heat treatments on the anodic polarization behavior of alloy 400 in acidic Na_2SO_4 solutions with different pH values and chloride contents has been studied. Alloy 400 is susceptible to intergranular corrosion (IGC) in 0.5 N Na_2SO_4 solution (pH 3) containing 0.2% CuCl_2. For the same heat treatment (soaking for one hour at 900 C), the extent of IGC appears to be significantly affected by the cooling rate, which is greater for faster cooling (e.g., water quenching). Aging the water-quenched alloy at 500 C enhances IGC susceptibility, and aging at higher temperatures imparts resistance to IGC. Note that addition of small amounts of hafnium has a beneficial effect on the resistance to IGC of alloy 400 under similar exposure conditions. An attempt has been made to rationalize the observations in terms of segregation of sulfur and phosphorus to the grain boundaries.

International Nuclear Information System (INIS)

BaZr_0_._1Ce_0_._7Y_0_._2O_3_-_#delta# (BZCY7) exhibits adequate proton conductivity as well as sufficient chemical and thermal stability over a wide range of SOFC operating conditions, while layered GdBa_0_._5Sr_0_._5Co_2O_5_+_#delta# (GBSC) perovskite deposited on a doped ceria electrolyte demonstrates advanced electrochemical properties. This research fully takes advantage of these advanced properties and develops novel protonic ceramic membrane fuel cells (PCMFCs) of Ni-BZCY7|BZCY7|GBSC. The results show that the open-circuit potential of 1.003 V, maximum power density of 430 mW cm"-"2, and a low polarization resistance of the electrodes of 0.08 #OMEGA# cm"2 are achieved at 700 "oC. With temperature increases, the total cell resistance decreases, among which electrolyte resistance becomes increasingly dominant over polarization resistance. The results also indicate that GBSC perovskite cathode is a good candidate for intermediate temperature PCMFC development, ...

International Nuclear Information System (INIS)

Photoelectrochemical current response of passive film was investigated for pure Cr and Fe-xCr (x = 8, 14, 18) alloys polarised potentiostatically in 0.1 kmol m"-"3 H_2SO_4 solution. Photoelectrochemical action spectrum could be separated into two or three constituents. These components were considered to be derived from Cr_2O_3 (E_g"o"p"t#propor to#3.6 eV) and Cr(OH)_3 (E_g"o"p"t#propor to#2.5 eV), and possibly CrO OH. The optical band gap, E_g"o"p"t, of each component was almost constant for various applied potentials, polarisation periods, and substrate materials. Flat band potential E_j_b at which the polarity of photocurrent changes from negative to positive with increasing potential was determined for each phase. E_j_b for Cr(OH)_3 on Cr and Fe-Cr alloys was about 250 mV_A_g_/_A_g_C_l. E_j_b for Cr_2O_3 was about 700 mV for Cr and about 500 mV for Fe-Cr alloys. E_j_b of Cr_2O_3 for Fe-Cr alloys slightly shifted in noble direction with increasing Cr content for Fe-Cr alloys. This ...

Energy Technology Data Exchange (ETDEWEB)

The corrosion properties of sputtered molybdenum and molybdenum silicide films in hydrochloric acid (HCl) have been studied by means of potentiodynamic measurements. Contributions from the substrate to the corrosion behaviour was avoided by depositing the films on inert aluminium oxide (Al{sub 2}O{sub 3}). The compositions studied were Mo, MoSi{sub 0.58}, MoSi{sub 1.04}, MoSi{sub 1.4} and MoSi{sub 1.9-2.1}. Characterisation of the samples was made by X-ray diffraction (XRD) and scanning electron microscopy (SEM) before and after corrosion. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) were used to analyse the polarised films. Corrosion of Mo{sub 3}Si was found in the molybdenum-rich samples (MoSi{sub 0.58}) containing the two phases Mo{sub 3}Si and Mo{sub 5}Si{sub 3}. Polarisation curves for these films showed one passivation peak at 228 mV vs. the saturated calomel electrode (SCE). The MoSi{sub 1.9-2.1} films had the best corrosion ...

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

Bi-U mixed oxides were synthesized by two methods and characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The samples were tested for the catalytic oxidation of carbon monoxide by oxygen. A stepwise redox mechanism consistent with the kinetic results is proposed. (orig.).

International Science & Technology Center (ISTC)

Development of Method and Technical Project of the Plant for Thermo-Vacuum Desorption of Tritium Oxide (HTO) from the Environmental Samples

Science.gov (United States)

Nanosized particles are important because of their unique properties, different from the bulk, which leads to their enhanced catalytic, photocatalytic and electronic properties. This work has dealt with three different nanoparticle systems in the context of three different aspects of nanoparticle properties: (a) photocatalytis (TiO2/metal) system, (b) luminescence (CdSe) (c) alloying (Pt-Ag and Pd-Ag). The initial photocatalytic enhancement obtained by adding noble metal on semiconductor nanoparticles, degrades as fast as in 15 minutes and questions their long-term performance. XANES measurements on such irradiated systems like TiO2/Au, TiO2/Pt, TiO2/Ir indicates a positive oxidation state of these noble metals which renders them as recombination centers for photo-excited electrons and explains the decreased photocurrent. The oxidation is caused by holes. The EXAFS results also indicate a change of the interfacial structure under the effect of ...

Science.gov (United States)

The effect of hydrogen sulfide (H2S) on the chemical looping combustion of coal-derived synthesis gas with bentonite-supported metal oxidesssuch as iron oxide, nickel oxide, manganese oxide, and copper oxideswas investigated by thermogravimetric analysis, mass spectrometry, and X-ray photoelectron spectroscopy (XPS). During the reaction with synthesis gas containing H2S, metal-oxide oxygen carriers were first reduced by carbon monoxide and hydrogen, and then interacted with H2S to form metal sulfide, which resulted in a weight gain during the reduction/sulfidation step. The reduced/sulfurized compounds could be regenerated to form sulfur dioxide and oxides during the oxidation reaction with air. The reduction/oxidation capacities of iron oxide and nickel oxide were not affected by the presence ...

Science.gov (United States)

A finite three-dimensional layer-by-layer photonic crystal with planar defects in a layer is shown to drastically modify the spontaneous emission rate of an embedded dipole. Finite-difference time-domain calculations with one quarter symmetric boundary condition and perfectly matched layer demonstrate the strong enhancement effects induced by the cavity resonance of defect modes and band-edge resonant modes. Simulation shows that the emission spectra are quite different when the position or polarization of the dipole is changed. Moreover, the extraction efficiency is calculated to observe the percentage of light leakage through a substrate.

Energy Technology Data Exchange (ETDEWEB)

The variations of thickness of the ozone layer over Denmark in the 1978-1994 period based on monthly figures are presented. (CLS)

British Library Electronic Table of Contents (United Kingdom)

Oxidation of propylene with oxygen, air and a mixture of nitrogen?oxygen in a barrier discharge is investigated. The selectivity towards formation of propylene oxide in pure oxygen is shown to be as high as 45 wt% and the propylene conversion ratio is found to be 12.9 wt%. In the oxidation with air, the propylene oxide selectivity is 23 wt%, while the conversion is 7.5 wt%. The values of propylene conversion and selectivity towards formation of propylene oxide in a barrier discharge are consistent with those obtained by the thermocatalytic methods for production of propylene oxide.

Energy Technology Data Exchange (ETDEWEB)

An investigation of the mechanism of the oxidation and ammoxidation of propylene was made. The products of the above reactions were acrylonitrile and acrolein for ammoxidation and oxidation, respectively. Also, the ammoxidation and oxidation of allyl alcohol, allyl amine, and their allylic deuterium substituted analogues was studied. It was concluded that oxidation and ammoxidation of propylene have the same rate determining step. Other conclusions about the reaction intermediates were also made.

International Nuclear Information System (INIS)

Doping of manganese (Mn3+/Mn4+) into the Aurivillius phase Pb1-xBi4+xTi4-xMnxO15 was carried out using the molten salt technique for various Mn concentrations (x=0, 0.2, 0.4, 0.6, 0.8, and 1). Single phase samples could be obtained in the composition range with x up to 0.6 as confirmed by X-ray and neutron diffraction analysis. Dielectric measurements show a peak at 801, 803, 813 and 850 K for samples with x=0, 0.2, 0.4, and 0.6, respectively, related to the ferroelectric transition temperature (Tc). The main contribution of the in-plane polarization for x?0.2 which was calculated from the atomic positions obtained by the structure analysis is the dipole moment in the Ti(1)O6 layer; however, for x?0.4 the polarization originates from the dipole moment in the Ti(2)O6 layer. Mn doping in the Pb1-xBi4+xTi4-xMnxO15 does not show any long range magnetic ordering. -- Graphical abstract: The dipole moment of TiO6 dependence of x in ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Norwegian Open Research Archives (NORA)

Full Text Available

International Nuclear Information System (INIS)

Planar channeling effects are studied in such well-oriented polycrystalline layers as NiSi_2 and Pb_2Si layers formed on single crystalline Si. Crystalline perfection of such layers is discussed by using the energy- and angular dependences of the axial and planar channeling yields. It has been shown that, in suitable conditions, the energy dependence of the planar yield is more sensitive to the spread of crystallite orientations in polycrystals than that of the axial one. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

The effects of reservoir layering and gravity segregation on nonisothermal injection and falloff tests are investigated. Results show that layering does not affect injection or falloff data if all the layers are permeable and accept fluids from the wellbore. In such cases, the average permeability, skin factor, and distance to the thermal front can be calculated using the techniques developed for homogeneous reservoirs. Special considerations have to be taken for cases where several layers are impermeable or are permeable but do not accept fluids of the well face. In the first case (impermeable layers), knowledge of the total thickness of the permeable layers is required for the existing techniques to be applied successfully. In the second case, the existing techniques cannot be applied, but characteristic responses from injection and falloff test are seen; ...

UK PubMed Central (United Kingdom)

Background. The Free Radical Theory of Aging mechanistically links oxidative stress to aging. Okinawa has among the world's longest-lived populations but oxidative stress in this...Full Text Available

UK PubMed Central (United Kingdom)

1. Nitric oxide generation is important in the regulation of resistance vessel tone. Until now, however, there has been no evidence of such a role for basal generation of nitric oxide in the skin microcirculation...Full Text Available

UK PubMed Central (United Kingdom)

Studies were conducted to quantitate the evolution of nitrogen oxides (NO_(x)) from soybean [Glycine max (L.) Merr.] leaves during in vivo nitrate reductase...Full Text Available

UK PubMed Central (United Kingdom)

The potential for oxidation of ammonia in anoxic marine sediments exists through anaerobic oxidation by Nitrosomonas-like organisms, utilizing nitrogen dioxide, coupling of nitrification,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Apparatus and method for selective measurement of tritium oxide in an environment which may include other radioactive components and gamma radiation, the measurement including the selective separation of tritium oxide from a sample gas through a membrane into a counting gas, the generation of electrical pulses individually representative by rise times of tritium oxide and other radioactivity in the counting gas, separation of the pulses by rise times, and counting of those pulses representative of tritium oxide. The invention further includes the separate measurement of any tritium in the sample gas by oxidizing the tritium to tritium oxide and carrying out a second separation and analysis procedure as described above.

International Nuclear Information System (INIS)

Reflection coefficients of electromagnetic waves in a nonuniform plasma layer with electrons, positive ions and negative ions, covering a metal surface are investigated by using the finite-difference-time-domain method. It is shown that the reflection coefficients are influenced greatly by the density gradient on the layer edge, layer thickness and electron proportion, i.e., the effect of the negative ions. It is also found that low reflection or high attenuation can be reached by properly choosing high electron proportion, thick plasma layer, and smooth density gradient in the low frequency regime, but sharp density gradient in the high frequency regime. (authors)

International Nuclear Information System (INIS)

The potential use of uranium in the field of catalysis is presented in the first part of this paper. Numerous applications of uranium binary oxides, as well as mixed oxides, are reviewed with a special emphasis on the role of U-Sb-O catalysts in selective oxidation (and ammoxidation) processes. Attempts are made to correlate the electronic structure of uranium, and especially the role that 5f electrons play in bonding, with its promising catalytic properties. In the second part, new data are given for uranium-bismuth mixed oxides in the catalytic oxidation of CO by O_2. Kinetic tests performed in a flow microreactor allow a mechanism to be proposed that involves the direct participation of lattice oxygen of the catalyst in the chemical process (redox mechanism). The high activity can be related to the ability of uranium to change reversibly its oxidation state. ...

UK PubMed Central (United Kingdom)

PurposeCataracts are often considered to be an unavoidable consequence of aging. Oxidative damage is a major cause or consequence of cortical and nuclear cataracts, the most common...Full Text Available

Science.gov (United States)

Metastable yttrium-oxide films are synthesized using reactive sputter deposition. The yttrium concentration of the as-deposited film is found to vary as a function of the sputter deposition rate. In addition to the synthesis of the cubic equilibrium phase...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.

Science.gov (United States)

May 31, 2011 ... A Theoretical Solid Oxide Fuel Cell Model for System Controls and Stability Design AUTHOR(S): Kopasakis, George; Brinson, Thomas; Credle, ...

Science.gov (United States)

Basic research of the structure and electronic properties of a-Si:H is reported with particular emphasis on the role of defects. The main findings are as follows: (1) low defect density material can be deposited at a high rate using SiH/sub 4/ diluted in He or Ne. Using Ar or Kr results in a high defect density and columnar material; (2) an electrical bias during deposition modifies the band gap, hydrogen concentration and structure; (3) the clustering of hydrogen in the regions between the columns is confirmed; (4) hydrogen diffusion is observed by NMR; (5) the oxidation of an a-Si:H surface results in approx. 3 x 10/sup 11/ cm/sup -2/ dangling bonds at the interface; (6) auger recombination of photoexcited carriers is a significant non-radiative mechanism at low temperatures; (7) non-radiative recombination by diffusion and capture at dangling bonds is observed at temperatures above 50 to 100/sup 0/K; (8) the defect density in doped and compensated a-Si:H is ...

International Nuclear Information System (INIS)

The corrosion and passivation behaviour of bulk polycrystalline martensite Ni50Mn30Ga20 and austenite Ni48Mn30Ga22 alloys was compared in electrolytes with different pH values. Linear anodic and cyclic potentiodynamic polarisation methods and anodic current transient measurements have been conducted for the alloys and their constituents to analyze free corrosion, anodic dissolution and passive layer formation processes. Electrochemically treated alloy surfaces were characterized with scanning electron microscopy (SEM) and angle-resolved x-ray photoelectron spectroscopy (XPS). The electrochemical response of both alloys is in principal similar and is dominated by the Ni oxidation. In acidic solutions (pH 0.5 and 5) a slightly higher reactivity is detectable for the martensitic alloy which is mainly attributed to enhanced dissolution processes at the multiple twin boundaries. In weakly acidic to strongly alkaline solutions (pH 5-11) both alloys ...

Energy Technology Data Exchange (ETDEWEB)

After periodic testing of a large-scale spray calciner/ceramic melter vitrification system over a 2-yr period, sufficient corrosion was noted on various parts of the vitrification system to warrant its disassembly and inspection. A majority of the 316 SS sintered metal filters on the spray calciner were damaged by chemical corrosion and/or high temperature oxidation. Inconel-601 portions of the melter lid were attacked by chlorides and sulfates which volatilized from the molten glass. The refractory blocks, making up the walls of the melter, were attacked by the waste glass. This attack was occurring when operating temperatures were >1200/sup 0/C. The melter floor was protected by a sludge layer and showed no corrosion. Corrosion to the Inconel-690 electrodes was minimal, and no corrosion was noted in the offgas treatment system downstream of the sintered metal filters. It is believed that most of the melter corrosion occurred during one ...

Energy Technology Data Exchange (ETDEWEB)

Polycrystalline Al2O3, magnesium aluminate spinel (MgAl2O4), MgO, Si3N4, and SiC were irradiated with various ions at 200-450 K, and microstructures were examined following irradiation using cross-section TEM. Amorphization was not observed in any of the irradiated oxide ceramics, despsite damage energy densities up to {similar_to}7 keV/atom (70 displacements per atom). On the other hand, SiC readily amorphized after damage levels of {similar_to}0.4 dpa at room temperature (RT). Si3N4 exhibited intermediate behavior; irradiation with Fe{sup 2+} ions at RT produced amorphization in the implanted ion region after damage levels of {similar_to}1 dpa. However, irradiated regions outside the implanted ion region did not amorphize even after damage levels > 5 dpa. The amorphous layer in the Fe-implanted region of Si3N4 did not appear if the specimen was simultaneoulsy irradiated with 1-MeV He{sup +} ions at RT. By comparison with published results, ...

Energy Technology Data Exchange (ETDEWEB)

Ellipsometric studies and reflectance measurements on five anodized coloured 304 stainless steel samples (Brown, Violet, Blue, Light Grey and Dark Grey) are reported. The optical properties, solar absorptance and thermal emittance of samples have been obtained. Measured values of absorptance lay between 0.75-0.87 together with a near normal emittance value approx. =0.10 at 100/sup 0/C. The total hemispherical emittance has been measured at 100 and 200/sup 0/C for the sample having the best selective surface. This study shows that the blue coloured surface has the most favourable combination of radiation properties. The surface deteriorates at temperatures above 210/sup 0/C. Oxidation is assumed to be the deterioration mechanism. The different samples exhibited difference in the /PSI/ and ..delta.. parameters as determined by ellipsometry both before and after heat treatments. When brown and violet samples were coated with a 125 nm layer of ...

Energy Technology Data Exchange (ETDEWEB)

Plans for the disposal of radioactive liquid and solid wastes presently stored in double-shell tanks at the Hanford Site call for retrieval and processing of the waste to create forms suitable for permanent disposal. Waste will be retrieved from a tank using a submerged slurry pump in conjunction with one or more rotating slurry jet mixer pumps. Pacific Northwest Laboratory (PNL) has conducted tests using simulated waste slurries to assess the effects of a impinging slurry jet on the corrosion rate of the tank wall and floor, an action that could potentially compromise the tank's structural integrity. Corrosion processes were investigated on a laboratory scale with a simulated neutralized cladding removal waste (NCRW) slurry and in a subsequent test with simulated neutralized current acid waste (NCAW) slurry. The test slurries simulated the actual NCRW and NCAW both chemically and physically. The tests simulated those conditions expected to exist in the respective double-shell ...

Energy Technology Data Exchange (ETDEWEB)

Two spreading experiments were performed at the FARO facility with prototypical core melts of a UO{sub 2}/ZrO{sub 2} weight percentage of 80/20. The objective was to obtain data on the spreading at flow rates of about 2 l/s of more than 100 kg prototypic high temperature oxide melt on a dry and wet stainless steel plate. For the second spreading test a shallow water layer of 10 mm was added on the substrate. Solutions for an isothermal spreading with a constant volume flux boundary condition in a sector with an angle {phi} are used to analyse the FARO L-32S experiment and to identify the source of discrepancies between the code results (THEMA, CORFLOW) and the experimental findings. The observed spreading behaviour of both FARO experiments can only be explained if an initial melt temperature below the liquidus temperature, i.e. about 120 K lower than the temperature measured by the UTS sensors is assumed. (orig.) [German] Zwei ...

International Nuclear Information System (INIS)

M-shell x-ray production cross sections for selected heavy elements, namely, _7_2Hf, _7_3Ta, _7_4W, _7_5Re, _7_6Os, _7_7Ir, _7_8Pt, _7_9Au, _8_3Bi, and _9_0Th, were measured for protons of energy 0.6--4.0 MeV. The experimental results are compared with the predictions of the first Born and semiclassical approximations for M-shell ionization; these data are also compared with the theory that accounts for the projectile's energy loss and Coulomb deflection as well as for the target's M-shell electron perturbed stationary state and relativistic nature (ECPSSR). Generally, fair agreement between the data and the ECPSSR theory is found. Some systematical discrepancies observed for the lightest elements (Hf, Ta, and W) are explained as possible ambiguities in the M-shell Coster-Kronig factors and fluorescence yields, which were used to convert theoretical M-subshell ionization cross sections to the total M-x-ray production cross sections. The experimental total M-shell ionization cross ...

Energy Technology Data Exchange (ETDEWEB)

Pulsed DC-plasma nitriding has been applied to form nitride layer having only a diffusion layer. The discharge current with the variation of discharge gases is proportional to the intensity of N{sub 2}{sup +} peak in optical emission spectroscopy during the plasma nitriding. The discharge current, microhardness in surface of substrate and depth of nitride layer increased with the ratio of N{sub 2} to H{sub 2} gas in discharge gases. When the ratio of N{sub 2} to H{sub 2} is lower than 60% in the discharge gases, high microhardness value of 1100Hv nitride layer which contains no compound layer has been formed. (author). 20 refs., 6 figs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

In the present work, the plasma nitriding behavior of a nickel based dental alloy was investigated. Plasma nitriding experiments carried out under constant gas mixture (15% H2?85% N2) for different process parameters including time (4, 6, 10, and 20?h) and temperature (400, 450, 500, and 550??C). Depending on nitriding parameters, it was found that triple or double layers formed on the surface of the samples. Increasing of treatment time and temperature has resulted in a double layer. ?N1 layer was in formed all nitrided samples. However, ?N2 layer is formed only at low temperatures and in short times. Layer growth of nickel based alloys increases until a critical time or a critical temperature reached. Above these critical values, it is observed that the layer thickness decreases. It was ...

KoreaScience (Korea)

Full Text Available