WorldWideScience
1

Thermal- and radiation-induced interactions of water on U02 surfaces.  

Energy Technology Data Exchange (ETDEWEB)

Most plans for the disposition of surplus nuclear materials involve storage in sealed containers where the evolution of gases from reactions of adsorbed water could present both pressure and flammability hazards[l] . Despite efforts such as calcining the material to minimize the water content prior to packaging, both residual moisture and readsorbed water may be present in the final containers . Given the anticipated temperature excursions during transportation and storage, this water may thermally desorb, increasing the pressure, and/or thermally dissociate to produce H2 gas, increasing flammability hazards . In addition, the radiation from the nuclear material may induce radiolysis of the water with the likely products being water vapor, H2, 02 and H2O2. In order to better understand the relative ...

2003-01-01

2

Coordination lanthanide compounds with thiosemicarbazide diacetic acid  

International Nuclear Information System (INIS)

A study was made on complex formation of thiosemicarbazide diacetic acid (H_2L) with neodymium (3), holmium (3) and erbium (3) in solutions and formation of complexes of metal: ligand=4:1 composition was revealed. Synthesis conditions were developed and products of LnLClxnH_2O, LnLOHxnH_2O, Na[LnL_2]xnH_2O composition were separated in crystalline state. It was shown, that H_2L behaves in these compounds as tripod ligand with O, O, N, N donor atoms.

3

Electronic energy bands and optical properties of LaH"2 and NdH"2  

International Nuclear Information System (INIS)

Electronic energy bands of LaH"2 and NdH"2 have been calculated by the composite-wave variational version of the augmented plane wave method. Crystal potentials for both the hydrides were constructed by the superposition of the atomic potentials of Herman and Skillman. From the band structure data, density of states, joint density of states, optical absorption spectra and Fermi surfaces of these two hydrides have been calculated. The results of the optical studies have been successfully compared with the experimental results of Weaver et al. From the theoretical point of view the present results for LaH"2 have been satisfactorily compared with the results of Gupta et al. Since no theoretical calculation exists for ndH"2, theoretical comparison, in this case, was not possible for ...

4

Absolute differential cross sections for the scattering of kilo-electron-volt O atoms  

International Nuclear Information System (INIS)

This paper reports measurements of absolute differential cross sections for the direct scattering of oxygen atoms by He, Ne, Ar, Kr, Xe, H_2, N_2, O_2, CO, CO_2, H_2O, SO_2, NH_3, CH_4, CF_4, and SF_6 targets. The measured cross sections include contributions from all elastic and inelastic processes that result in a fast neutral oxygen atom product. Cross sections are presented for 0.5- and 1.5-keV projectile energies over the laboratory angular range 0.2 degree endash 5 degree. When compared in the center-of-mass reference frame, these cross sections exhibit a high degree of similarity in both amplitude and angular dependence. The cross sections for N_2, CO, CO_2, and H_2O are inverted using a partial-wave analysis to yield empirical interaction potentials, which can then be used to extrapolate the measurements down to ...

5

Carbon monoxide - hydrogen combustion characteristics in severe accident containment conditions. Final report  

International Nuclear Information System (INIS)

Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the ...

1994-10-19

6

Co-production of hydrogen and carbon black from solar thermal methane splitting in a tubular reactor prototype  

British Library Electronic Table of Contents (United Kingdom)

This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen and carbon black (CB) as a high-value nano-material with the bonus of zero CO2 emission. The work focused on the development of a medium-scale solar reactor (10kW) based on the indirect heating concept. The solar reactor is composed of a cubic cavity receiver (20cm-side), which absorbs concentrated solar irradiation through a quartz window by a 9cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results in the temperature range 1740-2070K are presented: acetylene (C2H2) was the most important by-product with a mole fraction of up to about 7%, depending on the gas residence time. C2H2 content i...

2011-01-01

7

Solar syngas production from CO"2 and H"2O in a two-step thermochemical cycle via Zn/ZnO redox reactions: Thermodynamic cycle analysis  

British Library Electronic Table of Contents (United Kingdom)

Solar syngas production from CO"2 and H"2O is considered in a two-step thermochemical cycle via Zn/ZnO redox reactions, encompassing: 1) the ZnO thermolysis to Zn and O"2 using concentrated solar radiation as the source of process heat, and 2) Zn reacting with mixtures of H"2O and CO"2 yielding high-quality syngas (mainly H"2 and CO) and ZnO; the ZnO is recycled to the first, solar step, resulting in net reaction @bCO"2 + (1 - @b)H"2O -> @bCO + (1 - @b)H"2. Syngas is further processed to liquid hydrocarbon fuels via Fischer-Tropsch or other catalytic processes. Second-law thermodynamic analysis is applied to determine the cycle efficiencies attainable with and without heat recuperation for varying molar fractions of ...

2011-01-01

8

Correlated charge-changing uion-atom collisions. Final Technical Report  

International Nuclear Information System (INIS)

This document comprises the final technical report for atomic collisions research supported by DOE grant No. DE-FG02-87ER13778 from September 1, 2001 through August 31, 2004. The research involved the experimental investigation of excitation and charge-changing processes occurring in ion-atom and ion-molecule collisions. Major emphases of the study were: (1) interference effects resulting from coherent electron emission in H2, (2) production of doubly vacant K-shell (hollow ion) states due to electron correlation, and (3) formation of long-lived metastable states in electron transfer processes. During the period of the grant, this research resulted in 23 publications, 12 invited presentations, and 39 contributed presentations at national and international meetings and other institutions. Brief summaries of the completed research are presented below.

2005-11-01

9

Corrosion problems and resistance to corrosion of materials for production of steam generators for li.ght water reactor power plants  

International Nuclear Information System (INIS)

Briefly described is knowledge of crevice corrosion, corrosion cracking and denting. In evaluating the corrosion resistance of steam generator materials it is necessary to distinguish corrosion problems caused by the primary coolant eide and by the secondary circuit side. At present tubes are manufactured of 7 austenitic alloys of a different chemical composition, and available information shows that views on their corrosion resistance differ. Greatest attention has been devoted to corrosion cracking in the presence of HaOH. Findings related to I-600, I-800, I-690 and AISI 316 are given. Corrodibility by sulfur-containing products is now being studied, namely the intercrystalline corrosion cracking caused by the presence of H_2S_4O_6. Knowledge gained in this respect is summed up. (J.P.).

10

Elucidation of hydrogen mobility in tetralin under coal liquefaction conditions using a tritium tracer method. Effects of the addition of H2S and H2O; Tritium tracer ho wo mochiita sekitan ekika hanno jokenka deno tetralin no suiso idosei hyoka. Ryuka suiso oyobi mizu no tenka koka  

Energy Technology Data Exchange (ETDEWEB)

It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where ...

1996-10-28

11

Solvothermal Synthesis of a New Photochromic Azo Polymer and its Self-assembly Behavior  

British Library Electronic Table of Contents (United Kingdom)

An amphiphilic azobenzene diblock copolymer {2-[4-(4-methoxy phenyl azo)phenoxy]hexyl acrylate co-acrylic acid} was synthesized via reversible addition-fragmentation chain transfer polymerization in a hydrothermal reactor. The products were characterized by 1H-NMR, DSC, GPC and UV-Vis spectroscopy. Different self-assembly behaviors of this amphiphilic diblock copolymer in different organic solvent with different water content were investigated. In THF/H2O solution, the diblock copolymer self-assembled into spheres and the spheres would then change to vesicles with smaller size by increasing the volume of H2O. However, in DMSO/H2O solution, the sizes and morphologies of the self-assembled spheres would not change significantly with an enhanced amount of H2O. Photochromic behaviors of the am...

2010-01-01

12

Technical Key Figures for Photo-biological Hydrogen Production by Micro-algae  

International Nuclear Information System (INIS)

One regenerative path to produce hydrogen is the photo-biological hydrogen production by the green micro-alga Chlamydomonas reinhardtii. This process can be divided into three phases: a growth phase, a phase in which the algae adapt from oxygen production and CO2-fixation to fermentative H2 production, and a phase in which H2 is produced. In a research project carried out at Ruhr-Universitat Bochum, a new developed flat panel bioreactor was investigated. A system analysis was conducted and energetic and environmental key figures were determined. The intention of this assessment on a very early technological stage was to collect first technical data in order to classify the current technological status of the photo-biological H2 production to identify future potentials and to ...

2006-06-13

13

Particle size effects on the desorption properties of nanostructured magnesium dihydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM)  

International Nuclear Information System (INIS)

In the present work the hydrogen desorption properties of nanostructured magnesium hydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM) of elemental Mg powder under hydrogen are investigated. A profound effect of the particle size of synthesized MgH2 hydride on its hydrogen desorption characteristics measured by differential scanning calorimetery (DSC) has been found. All synthesized MgH2 powders are characterized by a double hydrogen desorption peak. Furthermore, below a certain threshold particle size the DSC desorption temperature of the peak doublet starts decreasing rapidly with decreasing of the mean hydride powder particle size (expressed as equivalent circle diameter-ECD). In contrast, the nanograin (crystallite) size of MgH2 does not seem to have apparent effect on the ...

2006-11-09

14

Radiation thermocatalytic processes of hydrogen production from water  

International Nuclear Information System (INIS)

The results of studies of radiation-thermocatalytic water decomposition in the 673-773 K temperature range in the presence of BeO and titanium Y-type zeolite are presented. It is found that radiation-thermocatalytic processes of hydrogen production from water are characterized by a lower activation energy (55.4 kJ/mole) as compared with thermocatalytic processes (88.4 kJ/mole). The radiation-thermocatalytic process rate in the presence of oxide systems is not an additive sum of rates of radiation-catalytic (at 296-300 K) and thermocatalytic processes of water decomposition. On the basis of obtained results the conclusion is made that during radiation-catalytic decomposition of water in a heterogeneous system BeO + H_2O the main contribution into this process is made by excitons, radiation-chemical yields of excitons and non-equilibrium charge-carriers are 4.4-4.5 excitons per 100 eV and 3.0-3.2 pairs ...

15

Presentation of Type B Peptide-MHC Complexes from Hen Egg White Lysozyme by TLR Ligands and Type I IFNs Independent of H2-DM Regulation.  

Science.gov (United States)

In APCs, presentation by MHC II molecules of the chemically dominant peptide from the protein hen egg white lysozyme (HEL) generates different conformational isomers of the peptide-MHC II complexes (pMHC). Type B pMHCs are formed in early endosomes from exogenous peptides in the absence of H2-DM, whereas in contrast, type A pMHC complexes are formed from HEL protein in late vesicles after editing by H2-DM. Thus, H2-DM edits off the more unstable pMHC complexes, which are not presented from HEL. In this study, we show that type B pMHC complexes were presented from HEL protein only after stimulation of dendritic cells (DC) with TLR ligands or type I IFN. Type I IFN contributed to most TLR ligand-induced type B pMHC generation, as presentation decreased in DC lacking the receptor ...

2011-07-25

16

The disruption of l-carnitine metabolism by aluminum toxicity and oxidative stress promotes dyslipidemia in human astrocytic and hepatic cells  

British Library Electronic Table of Contents (United Kingdom)

l-Carnitine is a critical metabolite indispensable for the metabolism of lipids as it facilitates fatty acid transport into the mitochondrion where b-oxidation occurs. Human astrocytes (CCF-STTG1 cells) and hepatocytes (HepG2 cells) exposed to aluminum (Al) and hydrogen peroxide (H2O2), were characterized with lower levels of l-carnitine, diminished b-oxidation, and increased lipid accumulation compared to the controls. g-Butyrobetainealdehyde dehydrogenase (BADH) and butyrobetaine dioxygenase (BBDOX), two key enzymes mediating the biogenesis of l-carnitine, were sharply reduced during Al and H2O2 challenge. Exposure of the Al and H2O2-treated cells to a-ketoglutarate (KG), led to the recovery of l-carnitine production with the concomitant reduction in ROS levels. It appears that the chann...

2011-01-01

17

Pretreatment of empty palm fruit bunch for production of chemicals via catalytic pyrolysis  

British Library Electronic Table of Contents (United Kingdom)

The effect of chemical pretreatments using NaOH, H2O2, and Ca(OH)2 on Empty Palm Fruit Bunches (EPFB) to degrade EPFB lignin before pyrolyis was investigated. Spectrophotometer analysis proved consecutive addition of NaOH and H2O2 decomposed almost 100% of EPFB lignin compared to 44% for the Ca(OH)2, H2O2 system while NaOH and Ca(OH)2 used exclusively could not alter lignin much. Next, the pretreated EPFB was catalytically pyrolyzed. Experimental results indicated the phenolic yields over Al-MCM-41 and HZSM-5 catalysts were 90wt% and 80wt%, respectively compared to 67wt% yield for the untreated sample under the same set of conditions. Meanwhile, the experiments with HY zeolite yielded 70wt% phenols.

2009-01-01

18

Crystallohydrate forms of trisubstituted uranyl orthophosphate  

International Nuclear Information System (INIS)

The conditions of production and the stability regions have been studied for the following crystallohydrates of trisubstituted uranyl orthophosphates: (UO_2)_3(PO_4)_2x6H_2O, (UO_2)_3(PO_4)_2x4H_2O, and (UO_2)_3(PO_4)_2xH_2O. Their thermal stability has been studied. It is shown that thermal dehydration of high-water hydrates at 220-240 deg C gives (UO_2)_3(PO_4)_2xH_2O. The anion composition and crystal structure of the compound remain constant up to 1000 deg C. The mixture of the composition of U_3O_8xU_3(PO_4)_4 is the final product of decomposition at 1000 deg C. The thermodynamic constants of dehydration processes have been calculated. A conclusion has been made about the polymer structure of the compound in which water is located between the uranylphosphate layers.

19

Outgassing study of thin films used for poly-SiGe based vacuum packaging of MEMS  

British Library Electronic Table of Contents (United Kingdom)

Thermal desorption spectroscopy (TDS) was used to study outgassing from polycrystalline SiGe (poly-SiGe), SiC and SiO"2 films used for poly-SiGe-based MEMS thin film vacuum package technology. Primary desorption products were found to be H"2, H"2O and CO"2. The CO"2 outgassing could be correlated with CF"4 plasma interface cleaning used for thick SiGe PECVD, which can leave carbon at the CF"4-plasma-cleaned interface.

2011-01-01

20

Species and Organ Diversity in the Effects of Hydrogen Peroxide on Superoxide Dismutase Activity In Vitro  

British Library Electronic Table of Contents (United Kingdom)

Abstract Superoxide dismutase (SOD) is ubiquitous in aerobic organisms and constitutes the first link in the enzyme scavenging system of reactive oxygen species. In the present study, species and organ diversity of SOD activity in a solution and in an in-gel assay system, as well as the effects of hydrogen peroxide (H2O2) on SOD activity, were investigated. In a solution assay system, SOD activity of jackfruit root, shoot, leaves, axes, and cotyledons, of maize embryos and endosperms, of mung bean leaves and seeds, of sacred lotus axes and cotyledons, and of rice and wheat leaves was increased by 1-15 mmol/L H2 O2. However, SOD activity in rice root and seeds, maize roots and leaves, mung bean roots and shoots, and wheat seeds was decreased by 1-15 mmol/L H2O2. The SOD activity of wheat ro...

2006-01-01

21

Benzene molecule is destroyed by ultraviolet and soft X-rays in circumstellar environment  

International Nuclear Information System (INIS)

Benzene molecules , present in the proto-planetary nebula CRL 618, are ionized and dissociated by ultraviolet (UV) and X-ray photons originated from the hot central star and by its fast wind. Ionic species and free radicals produced by these processes can lead to the formation of new organic molecules. The aim of this work is to study the photoionization and photodissociation processes of the benzene molecule, using synchrotron radiation and time-of-flight mass spectrometry. Mass spectra were recorded at different energies corresponding to the vacuum UV (21.21 eV) and soft X-ray (282-310 eV) spectral regions. The production of ions from the benzene dissociative photoionization is here quantified, indicating that C_6H_6 is more efficiently fragmented by soft X-ray than UV radiation, where 50% of the ionized benzene molecules survive to UV dissociation while only about 4% resist to C-rays. Partial ion yields of H and small hydrocarbons, such as ...

22

Mechanisms of radical removal by SO2  

DEFF Research Database (Denmark)

It is well established from experiments in premixed, laminar flames, jet-stirred reactors, flow reactors, and batch reactors that SO2 acts to catalyze hydrogen atom removal at stoichiometric and reducing conditions. However, the commonly accepted mechanism for radical removal, SO2 + H(+M) reversible arrow HOSO(+M), HOSO + H/OH reversible arrow SO2 + H-2/H2O, has been challenged by recent theoretical and experimental results. Based on ab initio calculations for key reactions, we update the kinetic model for this chemistry and re-examine the mechanism of fuel/SO2 interactions. We find that the interaction of SO, with the radical pool is more complex than previously assumed, involving HOSO and SO, as well as, at high temperatures also HSO, SH, and S. The revised mechanism with a high rate constant for H + SO2 recombination and with SO + H2O, rather than SO2 + ...

2007-01-01

23

Coir pith of the green coconut in the decontamination of radioactive aqueous effluent  

International Nuclear Information System (INIS)

Industrial segments as plant of mining, hospitals and university generate considerable volumes of radioactive wastewater containing uranium. The increasing development of the use of the nuclear energy to lead away to an expansion of the sectors of the nuclear fuel cycle, but it leads to security problems and it appears the necessity of control of the removing of uranium and radioactive effluent treatments. Researches evaluate if the technique of the biosorption would promote an alternative process with attractive characteristics of cost-benefit. The residual biomass from agricultural activities has been studied and used as adsorbent of metals and organic composts by low cost, abundance and for being biodegradable. In this work, it is presented the efficiency of the coir pith for the adsorption of ions UO_2"2"+. The coir pith is a by-product of the harvest of the coconut, a renewable natural source. The study was accomplished using the batch ...

24

Effect of rib height and pitch of the thermal performance of a passage disturbed by detached solid ribs  

Energy Technology Data Exchange (ETDEWEB)

Laser holographic interferometry and pressure measurements are presented for the effects of rib-to-duct height ratio (H/2B), rib pitch-to-height ratio (Pi/H), and Reynolds number (Re) on the spatially periodic-fully developed turbulent heat transfer and friction in a rectangular duct of width-to-height ratio of 4:1 with an array of ribs detached from one wall at a clearance to rib-height ratio of 0.38. The ranges of H/2B, Pi/H, and Re examined were 0.13 to 0.26, 7 to 13, and 5 {times} 10{sup 3} to 5 {times} 10{sup 4}, respectively. The difference in the H/2B dependence of the thermal performance between the detached and attached solid-rib array is documented H/2B = 0.17 and Pi/H = 10 are found to provide the best thermal performance for the range of parameters tested. Compact heat transfer and ...

1998-07-01

25

3D Time-Dependent Model Of The Dusty-Gas Atmosphere Of Comet 67P/Churyumov-Gerasimenko: Recent Improvements.  

Science.gov (United States)

Under support from the French Space Agency (CNES), a 3D+t dusty-gas model of Comet 67P/Churyumov-Gerasimenko is being developed, to compute, from the first 2014 Rosetta orbital data, the aerodynamic forces exerted on the Rosetta orbiter and on the descent lander. We report the recently developed dust dynamics part of the code. The multi-species (presently H2O and CO) gas code is optimized in terms of computational speed owing to the use of two complementary methods: (a) 3D+t Direct Simulation Monte Carlo (DSMC) runs in the non-equilibrium regions adjacent to the surface and very distant from it, and (b) solutions of the Navier-Stokes equations in-between. The model is used presently using Lamy et al. (Space Sci. Rev., 2007, 128, 23) coarse information on 67P nucleus shape and rotation, and a range of possible gas production rates Q for the early Rosetta observations at rh 3 AU (Q ...

2010-10-01

26

Synthesis of monohydric alcohols from CO and H2 on Fe/Sibunit catalysts  

British Library Electronic Table of Contents (United Kingdom)

It was demonstrated that R 2?R 4 saturated monohydric alcohols can be synthesized from CO and H2 in the presence of Fe catalysts containing a carbon support of the Sibunit type with granule sizes of 3?5, 1?2, and 0.05?0.1 mm in a fixed-bed reactor at 3 MPa and 240?300?C. It was found that the activity of Fe/Sibunit catalysts and their selectivity for the formation of liquid synthetic products increased with the size of granules and the amount of iron. The catalysts make it possible to obtain fatty alcohols, in which the fraction of R 2?R 4 alcohols is as high as 75%, in yields to 56 g/m3.

2011-01-01

27

Synthesis, crystallographic data, solubility and electrokinetic properties of copper-, nickel- and cobalt-uranylphosphate  

International Nuclear Information System (INIS)

A discussion is given concerning the transformation in acid medium of curite into copper-, nickel- and cobalt-uranylphosphate. From chemical, differentiel thermal and thermogravimetric analyses, the crystal-chemical formula are calculated as: Cu(UO_2/PO_4)_2.8H_2O, Ni(UO_2/PO_4)_2.7H_2O and Co(UO_2/PO_4)_2.7H_2O. The two last compounds crystallize in the triclinic system with space group P1 or P1(overscore) and the first one crystallizes in the tetragonal system with space group P4/nmm. The cell parameters are calculated. From solubility data, the solubility products are computed as 10sup(-12.8), 10sup(-9.5) and 10sup(-9.9) for the copper-, nickel- and colbalt-compound respectively. The electrokinetic properties of the three species are closely similar to those of natural meta-torbernite: the zeta-potential is negative and the point of zero ...

28

Comparison of plasma chemistries for inductively coupled plasma etching of InGaAlP alloys  

International Nuclear Information System (INIS)

Two plasma chemistries, i.e., CH_4/H_2/Ar and Cl_2/Ar, were compared for the etching of InGaP, AlInP, and AlGaP under inductively coupled plasma (ICP) conditions. While the etching with CH_4/H_2/Ar discharges appears to be ion driven, Cl_2/Ar discharges showed an additional strong chemical enhancement. The highest etch rate (#approx#1 #mu#m/min) for InGaP was achieved at high ICP source power (#>=#750 W) with the Cl_2/Ar chemistry. Cl_2/Ar discharges provided very smooth surfaces in all three materials with root-mean-square roughness measured by atomic force microscopy around 2 nm. This result may be due to the efficient ion-assisted product desorption in this chemistry. The etched near-surface region of InGaP (#approx#100 Angstrom) with Cl_2/Ar maintained almost the same stoichiometry as that of the unetched control. By contrast, the ...

1998-05-01

29

Range-resolved gas concentration measurements using tunable semiconductor lasers  

British Library Electronic Table of Contents (United Kingdom)

A method for range-resolved gas sensing using path-integrated optical systems is presented. The method involves dividing an absorption path into several measurement segments and extracting the gas concentration in each segment from two path-integrated measurements. We implemented the method with tunable lasers (a 1389-nm VCSEL and a 10.9-?m pulsed quantum cascade laser) and a group of retro reflectors (RRs) distributed along absorption paths. Using a rotating mirror with the VCSEL configuration, we could scan a group of seven tape RRs spaced by 10?cm in ??9?ms to extract an H2O concentration profile. Reduced H2O concentrations were recorded in the segments purged with dry air. Hollow corner cube RRs were used in the quantum cascade laser configuration at distances up to 1.1?km from the las...

2008-01-01

30

Heteropolyanion-based ionic hybrid solid: A green bulk-type catalyst for hydroxylation of benzene with hydrogen peroxide  

British Library Electronic Table of Contents (United Kingdom)

A novel heteropolyanion-based ionic hybrid was prepared by combining the divalent ionic liquid (IL) cation of 1,1'-(butane-1,4-diyl)-bis(3-methylimidazolium) with the Keggin-structured V-containing heteropolyanion, and characterized by ^1H NMR, FT-IR, ESI-MS, XRD, SEM, TG, BET surface area, melting point, and elemental analysis. Its catalytic activity was evaluated in the hydroxylation of benzene with aqueous H2O2, including the testing of the influence of organic cations, catalytic reusability and optimization of reaction conditions. This hybrid is characterized to be semi-amorphous nanoparticles with a IL-like composition. The hybrid catalyst leads to the liquid-solid biphasic reaction system for hydroxylation of benzene with H2O2, presenting such advantages as high catalytic activity, c...

2011-01-01

31

Collisions between H"+ and H_2 at kilo-electron-volt energies: Absolute differential cross sections for small-angle direct, single-, and double-charge-transfer scattering  

International Nuclear Information System (INIS)

Measurements of absolute differential cross sections for H"+-H_2 direct, single-, and double-charge-transfer scattering at 0.5, 1.5, and 5.0 keV are reported at laboratory scattering angles less than 1 degree with an angular resolution of approximately 0.02 degree. The cross sections exhibit deep interference oscillations in single-charge-transfer scattering, but no such oscillations are present in direct and double-charge-transfer scattering. Theoretical cross sections derived using the diatoms-in-molecules method to describe the molecular states in a semiclassical molecular-orbital three-state close-coupling model within a semiclassical framework agree satisfactorily with the experimental results.

32

Characterization of the combustion of biomass producer gas in a constant volume combustion bomb  

British Library Electronic Table of Contents (United Kingdom)

In this article a methodology is presented for studying the influence of the biomass moisture content and the biomass/air ratio on the producer gas composition and on the chemiluminescent emissions during the combustion process. Firstly, a mathematical model based on the thermo-chemical processes inside the gasifier is used to predict the composition of the producer gas as a mixture of CO, CO2, H2, N2, CH4 and H2O gases. Secondly, the predicted composition is introduced into a constant volume combustion bomb (CVCB), which simulates the typical conditions inside the combustion chamber of an internal combustion engine, in order to characterize its combustion under gasoline-type conditions through the instantaneous pressure and the detection of the spontaneous luminous radiation (chemilumines...

2010-01-01

33

Rapid Responding Palladium-Silver Surface Modified Microsensor for Hydrogen  

Science.gov (United States)

Most palladium thin film based hydrogen gas sensors have response and recovery times that are too long to make them useful in vehicular and stationary gas leak detection applications. In contrast, a palladium-silver thin film based microcantilever (MC) hydrogen gas microsensor is reported herein with near ideal response characteristics for use in these hydrogen economy related applications. Specifically, 3-10 second response and recovery times have been measured for these sensors in contrast to previous sensor response measurements of several to tens of minutes using Pd thin film and MC based sensing techniques. The much reduced response times observed in the present study are attributed to a wet chemical Pd-Ag thin film deposition technique and a gas conditioning protocol that produces a highly nanostructured, porous film that rapidly adsorbs and desorbs H2, allowing rapid equilibration with the ...

2010-01-01

34

Pitting corrosion resistance of high-alloy OCTG in CO_2 environment as affected by chlorides and sulfides  

International Nuclear Information System (INIS)

High general corrosion resistance of high-alloy OCTG (oil country tubular goods) to CO_2 may be limited by pitting corrosion in presence of chlorides and sulfides. The pitting resistance of 13% Cr steel, duplex and high Ni austenitic stainless steels have been examined by electrochemical measurements in a high temperature, high pressure autoclave simulating the well conditions. Each steel shows the pitting potential in CO_2-NaCl-H_2O system, the value of which being less noble as the Cl"- concentration and the temperature increase. The presence of H_2S is also detrimental. High alloying additions of Cr and Mo enhance pitting resistance whether or not H_2S is present. The corrosion potentials of these steels in the simulating well conditions in which oxygen is absent do not exceed the pitting potential. Therefore, pitting corrosion can not ...

35

Extended Gas in Seyfert Galaxies Near Infrared Observations of NGC 2110 and Circinus  

CERN Document Server

We present results of near--IR long-slit spectroscopy in the J and K bands of the Seyfert 2 galaxies NGC 2110 and Circinus, investigating the gaseous distribution, excitation, reddening and kinematics. In NGC 2110, the emission line ratio [FeII]/Pa beta increases towards the nucleus (to ~ 7). The nuclear [Fe II]1.257 (microns) and Pa beta lines are broader (FWHM ~ 500 km/s) than the H2 (2.121) line (FWHM ~ 300 km/s). Both these results suggest that shocks, driven by the radio jet, are an important source of excitation of [Fe II]. The H2 excitation appears to be dominated by X-rays from the nucleus. In Circinus, both [FeII]/Pa beta and H2/Br gamma decrease from ~ 2 at 4 arcsec from the nucleus to nuclear values of ~ 0.6 and ~ 1, respectively, suggesting that the starburst dominates the nuclear excitation, while the AGN dominates the ...

1998-01-01

36

Development of the ELEX process for tritium separation at reprocessing plants  

International Nuclear Information System (INIS)

The ELEX process for isotopic enrichment and separation of tritium from aqueous reprocessing effluents is described. After the development of an appropriate hydrophobic catalyst and the study of the separate constituent steps of the ELEX process, an integrated bench-scale installation with a detritiation capacity of 10 mol water per hour was constructed. It comprises essentially a 1.5 kW electrolyser and two 2 cm diameter by 3 m high exchange columns. In this mini-pilot the ELEX process was successfully demonstrated by detritiating more than 1000 dm"3 water containing up to 100 mCi tritium per dm"3, which is the feed concentration expected for application of the process in a reprocessing plant. The process decontamination factor was always larger than 100 and the overall tritium balance could be kept within the experimental errors of the various measurements. Depending on the duration of the runs, the volume reduction factor was between 10 and 15, but this factor will become much ...

1985-03-01

37

Pozzolanic behaviour of compound-activated red mud-coal gangue mixture  

International Nuclear Information System (INIS)

The pozzolanic behaviour of compound-activated red mud-coal gangue has been investigated through TG, DTA, XRD, FTIR and 27Al MAS NMR. From viewpoint of reaction kinetics, it is found that the pozzolanic reaction mechanism of the compound-activated red mud-coal gangue - lime system is clearly consistent with diffusion control up to 14 days, and the reaction rate constant calculated from Jander equation decreases with the increase of CaO addition in the system. The hydration products formed in the red mud-coal gangue - lime systems at ambient temperature are essentially aluminous C-S-H and Ca3Al2O6.xH2O. From TG analysis results, it is thought that the high amount of Ca(OH)2 in the pastes of studied system is not conducive to the continual increase of non-evaporable water content of the hydration products. Of particular interest, 27Al MAS NMR proved to be an effective technique to obtain valuable ...

2011-03-01

38

Biohydrogen production from desugared molasses (DM) using thermophilic mixed cultures immobilized on heat treated anaerobic sludge granules  

British Library Electronic Table of Contents (United Kingdom)

Hydrogen production from desugared molasses (DM) was investigated in both batch and continuous reactors using thermophilic mixed cultures enriched from digested manure by load shock (loading with DM concentration of 50.1 g-sugar/L) to suppress methanogens. H"2 gas, free of methane, was produced during batch cultivations, at different (DM) concentrations ranging from 1.5 g-sugars/L to 50.1 g-sugars/L. The highest yield of 237 ml-H"2/g-sugar was achieved during the DM batch fermentation at concentration of 2.1 g-sugars/L, whereafter the yield decreased with increasing DM concentration. The enriched hydrogen producing mixed culture achieved from the 16.7 g-sugars/L DM batch cultivation was immobilized on heat treated anaerobic sludge granules in an up-flow anaerobic sludge blanket (UASB) reac...

2011-01-01

39

Solvent extraction of well defined astatine species  

International Nuclear Information System (INIS)

During solvent extraction of At"-, [At(H_2O)_2]"+, AtCl, AtCl_2"- as well as of astatine compounds with higher oxidation states like AtO_n"-, the astatine species are changed into astatine of the oxidation state zero at the phase boundary independent on the organic solvent used. At(O) probably reacts with components of the organic phase or with decomposition products formed by chemical reactions or by radiolysis. The extraction coefficients of the astatine species depend on the experimental conditions applied, the redox potential, and on complex forming reactions or associations, resp., occuring in the aqueous phase. (author).

40

Production of pure yellow cake by ion-exchange processes employing sulphate elution  

International Nuclear Information System (INIS)

Recovery of uranium by ion-exchange processes from impure acid leach liquors is described, which produce a concentrated and pure eluate employing 10% sulphuric acid elution. In situations where resin is loaded to 45 g/ltr or more the acid consumption at ambient temperature is less than 4 kg of H_2SO_4 per kilogram of U_3O_8. Precipitation with an alkali such as ammonia or magnesia produces a yellow cake of high purity. (author).

1979-06-08

41

Quantitative analysis of sulfur forms of coal and the pyrolysis behavior of sulfur compounds; Sekitanchu no io kagobutsu no keitaibetsu gan`yuryo no teiryo to sono netsubunkai kyodo  

Energy Technology Data Exchange (ETDEWEB)

As part of the studies on coal utilization basics, considerations were given on quantification of sulfur forms of coal and the pyrolysis behavior of sulfur compounds. With the temperature raising oxidation method, a thermo-balance was connected directly to a mass analyzer, and the coal temperature was raised at a rate of 5{degree}C per minute and gasified. Peak division was performed on SO2 and COS production to derive sulfur forms of coal. Using the slow-speed pyrolysis method, production rates of H2S, COS, SO2 and mercaptans were measured at a temperature raising rate of 20{degree}C per minute. Sulfur content in char was also measured. With the quick pyrolysis method, a Curie point pyrolyzer was connected directly to a gas chromatograph, by which secondary reaction is suppressed, and initial pyrolytic behavior can be tracked. All kinds of coals produce a considerable amount of SO2 in the slow-speed ...

1996-10-28

42

?H2AX and cancer  

UK PubMed Central (United Kingdom)

Histone H2AX phosphorylation on a serine four residues from the carboxyl terminus (producing γH2AX) is a sensitive marker for DNA double-strand breaks (DSBs). DSBs may lead to cancer...Full Text Available

2008-12-01

43

Time-of-flight measurements of light molecular ions scattered at grazing incidence from a Ni(111) surface  

International Nuclear Information System (INIS)

A time-of-flight mass spectrometer has been constructed to measure the energy spectra of particles scattered by 10"0 with primary energies between 200 eV and 15 keV. The energy resolution #DELTA#E/E of the system is between 0.1 and 0.4%. Energy spectra of scattered molecules and their dissociation products are shown for 570 eV H_2"+ and 4430 eV N_2"+ as projectiles. Electron capture into unbound states of the neutral molecule, with perhaps some contribution from mutual scattering within the molecule, appears to explain the observed dissociation product energy spectra peak widths. (orig.).

44

Endonuclease IV of Escherichia coli is induced by paraquat  

International Nuclear Information System (INIS)

The addition of paraquat (methyl viologen) to a growing culture of Escherichia coli K-12 led within 1 hr to a 10- to 20-fold increase in the level of endonuclease IV, a DNase for apurinic/apyrimidinic sites. The induction was blocked by chloramphenicol. Increases of 3-fold or more were also seen with plumbagin, menadione, and phenazine methosulfate. H_2O_2 produced no more than a 2-fold increase in endonuclease IV activity. The following agents had no significant effect: streptonigrin, nitrofurantoin, tert-butyl hydroperoxide, #gamma# rays, 260-nm UV radiation, methyl methanesulfonate, mitomycin C, and ascorbate. Paraquat, plumbagin, menadione, and phenazine methosulfate are known to generate superoxide radical anions via redox cycling in vivo. A mutant lacking superoxide dismutase was unusually sensitive to induction by paraquat. In addition, endonuclease IV could be induced by merely growing the mutant in pure O_2. The levels of endonuclease ...

45

Further evidence for particle nucleation in clear air adjacent to marine cumulus clouds  

Science.gov (United States)

Observational evidence is presented for the nucleation of condensation nuclei (CN) in the clear air adjacent to an isolated, marine, cumulus cloud. Two separate regions of particle nucleation are identified: one located above the cloud top, and the second located downwind of the cloud near the level of the anvil outflow. The regions of high CN concentrations were located in extremely clean marine air, with unactivated aerosol surface area (excluding the nucleation mode) less than 2 sq micrometers/cu cm, air temperature -31 C, and higher relative humidities than the undisturbed environment. Vertical profile measurements downwind of the cloud showed that CN concentrations at the level of the anvil outflow (4.9 km) were 8 times greater than at any other level between the surface and 5.3 km. A conceptual model is formulated in which aerosol particles, sulfur dioxide (SO2), sulfuric acid vapor (H2SO4), dimethyl sulfide (DMS), ...

1994-11-01

46

Hermetically sealed aluminum electrolytic capacitor  

Science.gov (United States)

Aluminum electrolytic capacitors are presently not allowed on NASA missions because they outgas water and organic vapors, as well as H2. As a consequence, much larger and heavier packages of tantalum capacitors are used. A hermetically sealed aluminum capacitor has been developed under NASA-MSFC SBIR contracts. This capacitor contains a nongassing electrolyte that was developed for this application so internal pressure would remain low. Capacitors rated at 250 to 540 V have been operated under full load for thousands of hours at 85 and 105 C with good electrical performance and low internal pressure. Electrolyte chemistry and seal engineering concepts will be discussed.

1995-04-01

47

Production and Purification of UO_3 from rock phosphate deposits and its characterization  

International Nuclear Information System (INIS)

This study was carried out mainly to produce uranium trioxide (UO_3), matching standard commercial specification from rock phosphate deposits in Uro and Kurun at eastern part of the Nuba Mountains. A simplified hydrometallurgical procedure has been adopted for production of yellow cake from the ore. The powdered ore sample was leached with concentrated H_2SO_4 acid with and without addition of KCIO_3 as an oxidant. The crude yellow cake was precipitated from the resulting green solution of phosphoric acid as Na_2U_2O_7 and (NH_4)_2U_2O_7 and subsequently purified by TBP extraction (tributylphosphate) and hydrogen peroxide as UO_4.2H_2O. TBP purified product was dried and calcined to UO_3 whereas UO_4.2H-2O was dried and reduced to UO_3 by Na_2S_2O_3. Prior to precipitation of crude yellow cake, Fe in the phosphoric acid ...

2005-03-01

48

Fission product and actinide release from the debris bed test Phebus FPT4: synthesis of the post test analyses and of the revaporisation testing of the plenum samples  

International Nuclear Information System (INIS)

The Phebus FP project in an international reactor safety project. Its main objective is to study the release, transport and retention of fission products in a severe accident of a Light Water Reactor (LWR). The FPT4 test was performed with a fuel debris bed geometry, to look at late phase core degradation and the releases of low volatile fission products and actinides. Post Test Analyses results indicate that releases of noble gases (Xe, Kr) and high-volatile fission products (Cs, I) were nearly complete and comparable to those obtained during Phebus tests performed with a fuel bundle geometry (FPT1, FPT2). Volatile fission products such as Mo, Te, Rb, Sb were released significantly as in previous tests. Ba integral release was greater than that observed during FPT1. Release of Ru was comparable to that observed during FPT1 and FPT2. As in other Phebus tests, the Ru distribution suggests Ru ...

2006-03-01

50

Measurement of unpolarized semi-inclusive pi+ electroproduction off the proton  

Science.gov (United States)

Semi-inclusive pi+ electroproduction on protons has been measured with the CLAS detector at Jefferson Lab. The measurement was performed on a liquid-hydrogen target using a 5.75 GeV electron beam. The complete five-fold differential cross sections were measured over a wide kinematic range in Q2, x, z, and pT and over the complete range of azimuthal angles, phi, enabling us to separate the different structure functions, H2+eps*H1, H3 and H4. Our measurements of H2 at low-x were found to be in fairly good agreement with pQCD calculations, suggesting a precocious factorization of the process. Indeed, the conventional f(x)*D(z) term can account for almost all of the observed cross section, even at small z. The measured xF-distributions are in qualitative agreement with high energy data, which suggests a surprising numerical similarity between the spectator diquark fragmentation in the ...

2008-01-01

51

Experimental validation of upgraded designs for PERMCAT reactors considering mechanical behaviour of Pd/Ag membranes under H_2 atmosphere  

International Nuclear Information System (INIS)

The PERMCAT process chosen for the final clean-up stage of the Tokamak Exhaust Processing system of the ITER tritium plant combines in a single component a catalytic reactor and a permeator using Pd/Ag membranes. This study covers the mechanical behaviour of a Pd/Ag membrane under different operating conditions. The consequences of hydrogen uptake by the membrane during nominal operation but also during off-normal events are presented. Depending on the operating conditions, expansions around 2% and significant deformations are observed. Different mechanical designs of PERMCAT reactors are then discussed. The first generation comprises finger-type membranes and two new mechanical designs use either additional edge welded bellows or a special corrugated Pd/Ag membrane. These upgraded designs improve the robustness and simplify the geometry of the component. The experimental validation of these new units has been carried out based on the measurements of the processing ...

2007-10-01

52

Experience with fully operational solar-driven 10-ton LiBr/H2O single-effect absorption cooling system in Thailand  

British Library Electronic Table of Contents (United Kingdom)

A solar-driven 10-ton LiBr/H2O single-effect absorption cooling system has been designed and installed at the School of Renewable Energy Technology (SERT), Phitsanulok, Thailand. Construction took place in 2005, after which this system became fully operational and has been supplying cooling for our main testing buildings air-conditioning. Data on the systems operation were collected during 2006 and analyzed to find the extent to which solar energy replaced conventional energy sources. Here, we present these data and show that the 72m2 evacuated tube solar collector delivered a yearly average solar fraction of 81%, while the remaining 19% of thermal energy required by the chiller was supplied by a LPG-fired backup heating unit. We also show that the economics of this cooling system are domi...

2008-01-01

53

Detection of H2 Emission from Mira B in UV Spectra from the Hubble Space Telescope  

CERN Document Server

We present ultraviolet spectra of Mira's companion star from the Space Telescope Imaging Spectrograph (STIS) instrument on board the Hubble Space Telescope (HST). The companion is generally assumed to be a white dwarf surrounded by an accretion disk fed by Mira's wind, which dominates the UV emission from the system. The STIS UV spectrum is dominated by numerous, narrow H2 lines fluoresced by H I Ly-alpha, which were not detected in any of the numerous observations of Mira B by the International Ultraviolet Explorer (IUE). The high temperature lines detected by IUE (e.g., C IV 1550) still exist in the STIS spectrum but with dramatically lower fluxes. The continuum fluxes in the STIS spectra are also much lower, being more than an order of magnitude lower than ever observed by IUE, and also an order of magnitude lower than fluxes observed in more recent HST Faint Object Camera objective prism spectra from 1995. Thus, the ...

2001-01-01

54

Baryon history and cosmic star formation in non-Gaussian cosmological models: numerical simulations  

British Library Electronic Table of Contents (United Kingdom)

Abstract We present the first numerical,-N-body, hydrodynamical, chemical simulations of cosmic structure formation in the framework of non-Gaussian models. We study the impact of primordial non-Gaussianities on early chemistry (e-, H, H+, H-, He, He+, He++, H2, H+2, D, D+, HD, HeH+), molecular and atomic gas cooling, star formation, metal (C, O, Si, Fe, Mg, S) enrichment, Population-III (popIII) and Population-II-I (popII) transition and on the evolution of -visible- objects. We find that non-Gaussianities can have some consequences on baryonic structure formation at very early epochs, but the subsequent evolution at later times washes out any difference among the various models. When assuming reasonable values for primordial non-Gaussian perturbations, it turns out that they are responsi...

2011-01-01

55

Design of a new serotonin receptor 5-HT_1_A imaging agent based on "9"9"mTc  

International Nuclear Information System (INIS)

Serotonin is one of the neurotransmitters found in the brain and mediates brain functions. It is very well known that serotonin related brain abnormalities are exerted mainly via serotonin receptors in a similar manner to other neurotransmitters found in the brain. Recently, it has also been found that serotonin is involved in Alzheimer's disease either directly or indirectly by its actions on serotonergic neurons. To understand and treat the diseases caused by abnormalities in the serotonergic system in the brain, it is certain that its mechanism of function has to be well investigated. So far several 5-HT receptors and receptor subtypes have been well characterized. Moreover, serotonin agonists and antagonists acting on specific receptors are chemically synthesized and are now available for the prevention or treatment of serotonergic related diseases. In recent years, a great demand for developing neuroimaging agents has emerged for the diagnosis of abnormal brain functions in the ...

2004-07-01

56

Solar thermal cracking of methane in a particle-flow reactor for the co-production of hydrogen and carbon  

British Library Electronic Table of Contents (United Kingdom)

An experimental investigation on the thermal decomposition of CH4 into C and H2 was carried out using a 5kW particle-flow solar chemical reactor tested in a solar furnace in the 1300-1600K range. The reactor features a continuous flow of CH4 laden with mm-sized carbon black particles, confined to a cavity receiver and directly exposed to concentrated solar irradiation of up to 1720 suns. The reactor performance was examined for varying operational parameters, namely the solar power input, seed particle volume fraction, gas volume flow rate, and CH4 molar concentration. Methane conversion and hydrogen yield exceeding 95% were obtained at residence times of less than 2.0s. A solar-to-chemical energy conversion efficiency of 16% was experimentally reached, and a maximum value of 31% was numer...

2009-01-01

57

Neutrino cross sections with the MINER?A Experiment  

British Library Electronic Table of Contents (United Kingdom)

MINER?A is a high resolution, fully active detector designed to study neutrino interactions on nuclei in the NuMI beam at Fermi National Accelerator Laboratory. The active volume of the detector consists of 3 tons of plastic scintillator and includes embedded targets of 4He, C, H2O, Fe and Pb. The MINER?A collaboration expects to perform precision, A-dependent neutrino cross section measurements in the 1?10 GeV region, measure the axial form factor, and study nuclear shadowing of F2, quark-hadron duality and coherent pion production, among other topics. MINER?A began data taking in the fall of 2009. This paper describes the MINER?A experiment and provides an overview of the physics objectives along with estimated uncertainties of the measurements and the tentative projected schedule of dat...

2011-01-01

58

Multi-bubble sonoluminescense of europium(III) chloride in heavy water  

International Nuclear Information System (INIS)

Low fluorescence in the field of the Eu3+ photoluminescence spectrum is registered against a bach ground of the continuum of solvent emanation when multi-bubble sonolysis of EuCl3 (0.1 mol l-1) solutions saturated by the air and argon in heavy water. Distinctive sonoluminescence of europium ion is not found earlier in aqueous solutions. Possible reasons of low values of Eu3+ sonoluminescence as compared with other lanthanide ions (Ln3+), and effect of europium on the spectrum of solvent continuum connected, in particular, with the quenching of electron-excited products of the H2O* (O2O*) and Eu3+* sonolysis in the reactions of electron transfer are discussed

2008-09-01

59

Detection of free amino acids in proxies of marine aerosol by photoelectron resonance capture ionization aerosol mass spectrometry  

British Library Electronic Table of Contents (United Kingdom)

Photoelectron resonance capture ionization aerosol mass spectrometry (PERCI-AMS) has been applied to the analysis of proxies for marine aerosols with and without ozone; proxies used were mixed oleic acid-amino acid particles. The mechanism of ion formation for serine (104 m/z), glutamic acid (146 m/z), and phenylalanine (164 m/z) was dissociative electron attachment. This corresponds to loss of the hydrogen atom only, allowing for straightforward identification of the free amino acids. No ozonolysis products for the free amino acids were observed, even at high concentrations of ozone (500 ppm for 19 s). The direct detection of a novel gas-phase hydrated anion, [serine + H2O-H]-, is described. These preliminary results suggest that PERCI-AMS may provide an effective, simple and direct onlin...

2008-01-01

60

Introducing N-glycans into natural products through a chemoenzymatic approach**  

UK PubMed Central (United Kingdom)

The present study describes an efficient chemoenzymatic method for introducing a core N-glycan of glycoprotein origin into various lipophilic natural products. It was found...Full Text Available

2008-11-24

61

Ultrafast resonance energy transfer in bio-molecular systems  

British Library Electronic Table of Contents (United Kingdom)

In this article, we present our consistent efforts to explore the dynamical pathways of the migration of electronic radiation by using ultrafast (picosecond/femtosecond time scales) F?rster resonance energy transfer (FRET) technique. The ultrafast non-radiative energy migration from an intrinsic donor fluorophore (Tryptophan, Trp214) present in domain IIA of a transporter protein human serum albumin (HSA) to various non-covalently/covalently attached organic/inorganic chromophores including photoporphyrin IX (PPIX), polyoxovanadate [V15As6O42(H2O)]-6 clusters (denoted as V15) and CdS quantum dots (QDs) has been explored. We have also used other covalently/non-covalently attached extrinsic fluorogenic donors (NPA, ANS) in order to exploit the dynamics of resonance energy migration of an enz...

2010-01-01

62

Current status and future prospects of rocket propellants  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the current status and future prospects of rocket propellants and the development of rocket engines. The combinated rocket propellant of liquid oxygen (LO/sub 2/) and liquid hydrogen (LH/sub 2/) is so much effective that it is typically used for the main engine of the space shuttle of the U.S. LE-7 engine with the thrust output of 100 tons is being developed for H-2 launcher following H-1 launcher in Japan. Meanwhile, HM-60 engine is being developed for ARIANE-5 launcher in Europe. Although the LO/sub 2//LH/sub 2/ engine predominates in this field at present, a dual fuel engine combining LO/sub 2//LH/sub 2/ and LO/sub 2//hydrocarbon will be realized in near future. The fuel such as LNG (methane) and LPG (propane) will be used for rocket and ramjet engines. (10 refs, 2 figs, 3 tabs)

1987-06-20

63

In vitro H2AX phosphorylation and micronuclei induction in human fibroblasts across the Bragg curve of a 577MeV/nucleon Fe incident beam  

Energy Technology Data Exchange (ETDEWEB)

The space environment consists of a varying field of radiation particles including high-energy ions, with spacecraft shielding material providing the only major protection to astronauts from harmful exposure. Unlike low-linear energy transfer (LET) {gamma} or X-rays, the presence of shielding does not always reduce the radiation risks for energetic charged particle exposure, since the dose delivered by the charged particle increases sharply as the particle approaches the end of its range, a position known as the Bragg peak. The Bragg curve does not necessarily represent the biological damage along the particle traversal, and the 'biological Bragg curve' is dependent on the energy and the type of the primary particle, and may vary for different biological endpoints. Here we used a unique irradiation geometry to measure the biological response across the Bragg curve in human fibroblasts exposed to 577MeV/nucleon incident Fe ions in vitro. Polyethylene shielding was used ...

2006-10-15

64

Study of the susceptibility of an austenitic stainless steel stabilized with niobium to stress corrosion damage in a H_2S medium (SSC) and to intergranular corrosion (IGC) in other aggressive environments  

International Nuclear Information System (INIS)

Behavior to hydrogen damage caused by stress corrosion in a H_2S medium (SSC) and to intergranular corrosion (IGC) in different mediums, such as oxalic acid (C_2H_2.2H_2O), iron sulphate-50% sulfuric acid (Fe_2(SO_4)_3-50% H_2SO_4), nitric acid (HNO_3), copper sulphate-16% sulfuric acid (CuSO_4.5H_2O-16% H_2SO_4) and cooper sulphate-50% sulfuric acid (CuSO_4.5H_2O-50% H_2SO_4), is studied in an AISI 347 austenitic stainless steel stabilized with 0.61 mass % Nb and hot rolled to a seamless pipe with 273.1 mm in diameter and 18.2 mm in thickness. (Author) 12 refs.

1998-01-01

65

Top quark physics: Summary  

International Nuclear Information System (INIS)

This talk summarizes recent progress in top quark physics studies for high energy linear electron-positron colliders as presented at the LCWS2000 Workshop at Fermilab. New results were presented for top pair production at threshold and in the continuum, as well as for top production at #gamma##gamma# colliders.

2001-07-09

66

Development Document for Proposed Effluent Limitations Guidelines and Standards for the Concentrated Aquatic Animal Production Industry Point Source Category.  

Science.gov (United States)

This section presents background information supporting the development of effluent limitations guidelines and standards for the concentrated aquatic animal production (CAAP) point source category. Section 1.1 presents the legal authority to regulate the ...

2002-01-01

67

Variability of indicator values for ozone production sensitivity: a model study in Switzerland and San Joaquin Valley (California)  

International Nuclear Information System (INIS)

The threshold values of indicator species and ratios delineating the transition between NO_x and VOC sensitivity of ozone formation are assumed to be universal by various investigators. However, our previous studies suggested that threshold values might vary according to the locations and conditions. In this study, threshold values derived from various model simulations at two different locations (the area of Switzerland by UAM Model and San Joaquin Valley of Central California by SAQM Model) are examined using a new approach for defining NO_x and VOC sensitive regimes. Possible definitions for the distinction of NO_x and VOC sensitive ozone production regimes are given. The dependence of the threshold values for indicators and indicator ratios such as NO_y, O_3/NO_z, HCHO/NO_y, and H_2O_2/HNO_3 on the definition of NO_x and VOC sensitivity is discussed. Then the variations of threshold values under low emission conditions ...

68

A pilot-scale jet bubbling reactor for wet flue gas desulfurization with pyrolusite.  

Science.gov (United States)

MnO2 in pyrolusite can react with SO2 in flue gas and obtain by-product MnSO4 x H2O. A pilot scale jet bubbling reactor was applied in this work. Different factors affecting both SO2 absorption efficiency and Mn2+ extraction rate have been investigated, these factors include temperature of inlet gas flue, ration of liquid/solid mass flow rate (L/S), pyrolusite grade, and SO2 concentration in the inlet flue gas. In the meantime, the procedure of purification of absorption liquid was also discussed. Experiment results indicated that the increase of temperature from 30 to 70 K caused the increase of SO2 absorption efficiency from 81.4% to 91.2%. And when SO2 concentration in the inlet flue gas increased from 500 to 3000 ppm, SO2 absorption efficiency and Mn2+ extraction rate decreased from 98.1% to 82.2% and from 82.8% to 61.7%, respectively. The content of MnO2 in pyrolusite had a neglectable effect on SO2 absorption ...

2005-01-01

69

Tin doping in spray pyrolysed indium sulfide thin films for solar cell applications  

British Library Electronic Table of Contents (United Kingdom)

This paper presents studies carried out on tin-doped indium sulfide films prepared using Chemical Spray Pyrolysis (CSP) technique. Effect of both in-situ and ex-situ doping were analyzed. Ex-situ doping was done by thermal diffusion, which was realized by annealing Sn/In2S3 bilayer films. In-situ doping was accomplished by introducing Sn into the spray solution by using SnCl45H2O. Interestingly, it was noted that by ex-situ doping, conductivity of the sample enhanced considerably without affecting any of the physical properties such as crystallinity or band gap. Analysis also showed that higher percentage of doping resulted in samples with low crystallinity and negative photosensitivity. In-situ doping resulted in amorphous films. In contrast to ex-situ doping, `in- situ doping' resulted i...

2010-01-01

70

The mechanism of thorium biosorption by Rhizopus arrhizus  

Energy Technology Data Exchange (ETDEWEB)

Inactive cells of Rhizopus arrhizus have been documented to exhibit a high thorium biosorptive uptake (170 mg/g) from aqueous solutions. The mechanism of thorium sequestering by this biomass type was investigated following the same method as for the uranium biosorption emchanism. The thorium sequestering mechanism appeared somewhat different from that of uranium. Experimental evidence is presented which indicates that, at optimum biosorption pH (4), thorium coordinates with the nitroge of the chitin cell wall network and, in addition, more thorium is adsorbed by the external section of the fungal cell wall. At pH 2 the overall thorium uptake is reduced. The kinetic study of thorium biosorption revealed a very rapid rate of uptake. Unlike uranium at optimum solution pH, Fe/sup 2 +/ and Zn/sup 2 +/ did not interfere significantly with the thorium biosorptive uptake capacity of R. arrhizus.

1982-04-01

71

Plasma nitriding of AISI 304 steel  

International Nuclear Information System (INIS)

In the present investigation, the properties of plasma nitrided AISI 304 steel were studied by changing the presence of nitrogen in the gas mixture. The plasma nitriding was performed at temperature -560 deg C, pressure -4 mbar and duration 24 hours. The nitrided samples were characterized by evaluating the phase composition, micro hardness, and diffusion layer thickness. The phase analysis indicates the mixed phases of CrN and Fe_3N, Fe_3N and Fe_4N which has the highest intensity. The results show the glow discharge plasma nitriding in presence of N_2 (80 vol. %) and H_2 (rest) produced higher hardness as well as higher case depth. (author)

2004-09-01

72

Influence of pH, temperature and thermal treatment on site corrosion of SAE 304 steel in chlorinated solutions  

International Nuclear Information System (INIS)

The electrochemical behaviour and fracture morphology of homogenized and sensitized type SAE 304 stainless steel U bent specimens, in 3% NaCl solution, at pH=2.0 and pH=7.0 both at room temperature and 100"0C was studied. Polarization curves, galvanostatic and potentiostatic experiments were run. It could be observed that high temperature and low pH favour transgranular cracking and longer sensitization times lower fracture time and tend to give rise to intergranular fracture. Light sensitization can produce transgranular cracking even at room temperature, when the homogenized alloy does not present stress-corrosion cracking for the same condition. (Author).

73

Emittance of boehmite and alumina films on 6061 aluminium alloy between 295 and 773 K  

International Nuclear Information System (INIS)

The total hemispherical emittance of an oxide film that formed on 6061-T6 aluminium alloy parts in the Tower Shielding Reactor-II at Oak Ridge National Laboratory was measured from 295 to 773 K using an emissometer and/or a calorimeter. The emittance of this film was critically needed for heat transfer calculations in a simulated loss-of-coolant accident of the reactor. X-ray diffraction analysis identified the film as boehmite (Al_2O_3 x H_2O), which dehydrated to alumina (Al_2O_3) upon heating above 473 K. The measured emittances for the alumina film are in excellent agreement with published values for anodized aluminum films and for bulk alumina. Published values of the emittance of boehmite could not be found for comparison, but evidence is presented that some anodization processes for aluminum yield boehmite and not alumina films.

1991-01-01

74

Chemical composition and electronic structure of passive films formed on Alloy 600 in acidic solution  

Energy Technology Data Exchange (ETDEWEB)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer conferring improved protection.

2008-03-15

75

Chemical composition and electronic structure of passive films formed on Alloy 600 in acidic solution  

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer conferring improved protection.

2008-03-01

76

Characterization and Wear Behavior of Plasma Nitrided Nickel Based Dental Alloy  

British Library Electronic Table of Contents (United Kingdom)

In the present work, the plasma nitriding behavior of a nickel based dental alloy was investigated. Plasma nitriding experiments carried out under constant gas mixture (15% H2?85% N2) for different process parameters including time (4, 6, 10, and 20?h) and temperature (400, 450, 500, and 550??C). Depending on nitriding parameters, it was found that triple or double layers formed on the surface of the samples. Increasing of treatment time and temperature has resulted in a double layer. ?N1 layer was in formed all nitrided samples. However, ?N2 layer is formed only at low temperatures and in short times. Layer growth of nickel based alloys increases until a critical time or a critical temperature reached. Above these critical values, it is observed that the layer thickness decreases. It was ...

2011-01-01

77

Absolute differential cross sections for electron capture and loss by kilo-electron-volt hydrogen atoms  

International Nuclear Information System (INIS)

This paper reports measurements of absolute differential cross sections for electron capture and loss for fast hydrogen atoms incident on H_2, N_2, O_2, Ar, and He. Cross sections have been determined in the 2.0- to 5.0-keV energy range over the laboratory angular range 0.02 degree--2 degree, with an angular resolution of 0.02 degree. The high angular resolution allows us to observe structure at small angles in some of the cross sections. Comparison of the present results with those of other authors generally shows very good agreement.

78

Space nuclear power requirements for ozone layer modification  

International Nuclear Information System (INIS)

This work estimates the power requirements for using photochemical processes driven by space nuclear power to counteract the Earth's ozone layer depletion. The total quantity of ozone (O_3) in the Earth's atmosphere is estimated to be about 4.7 x 10"3"7 molecules. The ozone production and destruction rates in the stratosphere are both on the order of 4.9 x 10"3"1 molecules/s, differing by a small fraction so that the net depletion rate is about 0.16 to 0.26% per year. The delivered optical power requirement for offsetting this depletion is estimated to be on the order of 3 GW. If the power were produced by satellite reactors at 800 km altitude (orbit decay time #approx# 300 years), some means of efficient power beaming would be needed to deliver the power to stratospheric levels (10--50 km). Ultraviolet radiation at 140--150 nm could have higher absorption rates in O_2 (leading to production of atomic oxygen, which can combine with O_2 to form ...

1992-01-13

79

Preparation of Eu-doped #beta#- and 15R-SiAlONs by ammonia nitridation of the precursor obtained using aluminum glycine gel  

International Nuclear Information System (INIS)

Synthesis of Eu-doped #beta#- and 15R-SiAlONs was studied by the ammonia nitridation of precursors derived from an #alpha#-Si_3N_4 fine powder dispersed in aluminum glycine gel with various Si/Al ratio and post-annealing in a nitrogen pressure furnace. The largest amount of #beta#-SiAlON was observed in the product at 1750 deg. C for Si/Al = 1/1 with small amounts of both #alpha#- and 15R-SiAlON impurities. The product showed two emissions at around 420 nm and 560 nm. The emission intensities decreased with increasing amount of #beta#-SiAlON. The former and latter emissions were assigned to Eu"2"+ in the 15R- and #alpha#-SiAlONs impurities. A mixture of Eu-doped 15R-SiAlON with #alpha#-Al_2O_3 impurity was obtained for Si/Al = 1/6, using AlN together with Al(NO_3)_3.9H_2O in a 2/1 atomic ratio as the aluminum source. It showed a bluish-white emission at 450 nm under 254 nm radiation.

2009-11-13

80

Preliminary Thermo-Hydraulic Analysis of Sulfuric Acid Loop for NHDD System  

International Nuclear Information System (INIS)

Very High Temperature gas cooled nuclear Reactor (VHTR), which was coupled with Sulfur-Iodine (SI) thermo-chemical cycle, has been selected for the Nuclear Hydrogen Development and Demonstration (NHDD) project in Korea Atomic Energy Research Institute. Among the various hydrogen production methods, Sulfur-Iodine (SI) thermo-chemical cycle is a good method as a massive hydrogen production without CO2 emission. In SI cycle, the sulfuric acid decomposition is one issue for the material corrosion on high temperature and pressure condition. For the simulation of the sulfuric acid decomposition, we designed a sulfuric acid loop with a small-scale gas loop which is simulated for the integrity and feasibility tests on a H2SO4 decomposition process. The primary objective of the loop is to validate the corrosion and the mechanical performances of a key component of the NHDD, Process Heat Exchanger (PHE). In this ...

2010-10-01

81

Optimized, Competitive Supercritical-CO_2 Cycle GFR for Gen IV Service  

International Nuclear Information System (INIS)

An overall plant design was developed for a gas-cooled fast reactor employing a direct supercritical Brayton power conversion system. The most important findings were that (1) the concept could be capital-cost competitive, but startup fuel cycle costs are penalized by the low core power density, specified in large part to satisfy the goal of significant post-accident passive natural convection cooling; (2) active decay heat removal is preferable as the first line of defense, with passive performance in a backup role; (3) an innovative tube-in-duct fuel assembly, vented to the primary coolant, appears to be practicable; and (4) use of the S-Co2 GFR to support hydrogen production is a synergistic application, since sufficient energy can be recuperated from the product H2 and 02 to allow the electrolysis cell to run 250 C hotter than the reactor coolant, and the water boilers can be used for reactor decay ...

82

Local and regional ozone production: Chemistry and transport  

International Nuclear Information System (INIS)

The EUROTRAC sub-project ''Tropospheric Ozone Research'' (TOR) follows a dual strategy: - Observation of the chemical processes contributing to the oxygen balance directly in the atmosphere; - Establishment of a validated data base for model calculations. Both tasks require simultaneous measurements of a wide range of chemical and meteorological components. In the case of the investigation of the chemical processes, it is also desirable to measure the free radicals directly involved in ozone production. In the project described, a measuring station was set up. For a period of two years and a half, continuous measurements were made of ozone and its chemical precursors (NO, NO_2, NO_y, VOC, CO), as well as other photooxidants (H_2O_2 and organic hydroperoxides, organic nitrates), the photolysis frequency of NO_2, and meteorological parameters (wind, temperature, moisture, aerosols). The station was located on the Schauinsland ...

83

Effects of ionizing radiation on properties of monolayer and multilayer flexible food packaging materials  

International Nuclear Information System (INIS)

Volatile compounds produced in flexible food packaging materials (LDPE, EVAc, PET/PE/EVOH/PE) during electron beam irradiation were isolated by purge and trap technique and identified by combined gas chromatography-mass spectrometry (GC/MS), after thermal desorption and concentration. For comparison purposes non-irradiated films were also studied. Film samples were irradiated at low (5 kGy, corresponding to cold pasteurization), intermediate (20 kGy, corresponding to cold sterilization) and high (100 kGy) doses. It was observed that a number of volatile compounds are produced after irradiation in all cases. Furthermore the amounts of all volatile compounds increase with increasing irradiation dose. Both primary (methyl-derivatives etc.) as well as secondary i.e. oxidation products (ketones, aldehydes, alcohols, carboxylic acids etc.) are produced upon irradiation. These products may affect organoleptic properties and thus shelf-life of ...

1999-05-01

84

Detection of the heavy Higgs boson at #gamma##gamma# colliders  

International Nuclear Information System (INIS)

We consider the possibility of detecting a heavy Higgs boson (m_H>2m_Z) in proposed #gamma##gamma# colliders through the semileptonic mode #gamma##gamma##->#H#->#ZZ#->#q bar ql"+l-. We show that due to the nonmonochromatic nature of the photon beams produced by the laser-backscattering method, the resultant cross section for Higgs production is much smaller than the on-resonance cross section, and generally decreases with increasing collider energy. Although continuum ZZ production is expected to be negligible, we demonstrate the presence of, and calculate sizable backgrounds from, #gamma##gamma##->#l"+l-Z,q bar qZ, with Z#->#q bar q,l"+l-, respectively, and #gamma##gamma##->#t bar t#->#b bar bl"+l-#nu# bar #nu#. This channel may be used to detect a Higgs boson of mass m_H up to around 350 GeV at a 0.5 TeV e"+e- collider, assuming a nominal yearly luminosity of 10--20 fb"-"1.

85

A New and Sound Technology for Biogas from Solid Waste and Biomass  

International Nuclear Information System (INIS)

Organic waste, as a main constituent of municipal solid waste, has as well as solid biomass a high potential for biogas generation. Despite the importance of biogas generation from these materials, the availability of large-scale biogas processes lacks behind the demand. A newly developed double-stage solid-liquid biogas process, consisting of an open hydrolysis stage and a fixed-bed methane reactor, allows the biogas production from almost all biodegradable solid waste and renewable resources like maize, grass, sugar cane, etc. Furthermore, residues from industrial processes, like the glycerine waste water from biodiesel production, can also be converted into biogas successfully. Due to the strong separation of hydrolysis and methanation, the process is extremely stable. No malfunction has been detected so far. The open hydrolysis releases CO_2 and allows oxidation of sulfur. Consequently, the biogas has a high methane (>72%) and low ...

2009-04-01

86

Construction of a novel bifunctional biogenic amine receptor by two point mutations of the H2-histamine receptor.  

UK PubMed Central (United Kingdom)

BACKGROUND: H2-histamine receptors mediate a wide range of physiological functions extending from stimulation of gastric acid secretion to induction of human promyelocyte differentiation. We have previously...Full Text Available

1995-03-01

87

2-[(4-MepyH)2]2+ - GLTRS - NASA  

Science.gov (United States)

Synthesis and Structural Characterization of a Novel Indium Mercapto Derivative [Clln(SCH2(CO)O)2]2-[(4-MepyH)2]2+. AUTHOR(S): ...

89

Molar extinction coefficients in aqueous solutions of some alkaline earth chlorides  

International Nuclear Information System (INIS)

Molar extinction coefficients for the solid solutes in aqueous solutions of some alkaline earth chlorides such as MgCl_2.6H_2O, CaCl_2, SrCl_2.6H_2O and BaCl_2.2H_2O have been determined at 81, 356, 511, 662, 1173 and 1332 keV energies in different concentration using the narrow beam transmission methods. (author)

1999-12-21

90

Application of 'waste' wood-shaving bottom ash for adsorption of azo reactive dye.  

Science.gov (United States)

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that ...

2008-04-23

91

Specific adsorption of arsenic and humic acid on Pt and PtO films  

International Nuclear Information System (INIS)

A study of specific adsorption of arsenic (As) and humic acid (HM) onto Pt and PtO films using cyclic voltammetry and cyclic massogram in 0.5-M H_2SO_4 is presented, which may serve as an alternative to studies involving specific adsorption of these species on soil minerals. Adsorption of As is normally evaluated by conducting batch adsorption experiments, followed by analysis using hydride-generation atomic absorption spectrophotometry (HGAA) or inductively coupled plasma-optical emission spectrometry (ICP-OES). We found that specific adsorption of As and HM depends both on the surface and on these species present in the adsorption solution. HM does not desorb previously adsorbed As at the HM concentrations used in the present study, but it does co-adsorb with As from a 1 x 10"-"6-M aqueous solution of As_2O_3 containing 1 mg of carbon L"-"1 HM. Arsenic adsorbs strongly on Pt in ...

2010-07-01

92

Product identification in industrial batch fermentation using a variable forgetting factor  

British Library Electronic Table of Contents (United Kingdom)

For reliable operation and the optimization of production, industrial fermentation processes require appropriate tools for monitoring the process in real time. This work presents the structure and operation of a soft sensor for the on-line monitoring of biomass and product concentration during salinomycin and bacitracin fermentation in an industrial, 80-m^3 batch reactor; moreover it provides a tool for evaluation of batch production verified in industrial application. The process estimation algorithm consists of decoupled growth and product models, which ensures an unbiased convergence of the estimator and the robustness of the model. The production of secondary metabolites is described with a non-structured model upgraded with a variable forgetting factor that demonstrated a successful e...

2011-01-01

93

Numerical Modeling of the RF Plasma Production in URAGAN-2M Stellarator with Crankshaft Antenna  

International Nuclear Information System (INIS)

The qualitative technique of the analysis of the efficiency of the RF plasma production is presented in which the solution of boundary problem for Maxwell's equations is only necessary. The analysis of the character of the plasma production process with the crankshaft antenna in Uragan-2M stellarator is carried out. The discussion of the calculations results is presented.

2006-01-01

94

Spectral investigation of primary uranyl orthophosphate  

International Nuclear Information System (INIS)

By methods of vibrational (infrared, Raman) and PMR spectroscopy, crystallohydrate forms of monosubstituted uranyl orthophosphate have been examined. The vibrational frequencies of the groupings from the compounds were identified. The existence of non-equivalent H_2PO_4"--groups in the substances under investigation was ascertained. It has been suggested that one of them is a bridged group, and the other is the end group. A fragment of the VO_2(H_2PO_4)_2 hydrate structure is given, its main constituents being uranylphosphate chains. The analysis of water vibrations assumes coordination of one mole of H_2O in VO_2(H_2PO_4)_2:3H_2O to uranium, while two other molecules are only hydrogen-bonded with phosphate anions. Absorption within the region of 2100-2550 cm"-"1 is assigned to ...

95

A Computer Simulation of the Electronic Structure of Leucine in Aqueous Solution  

British Library Electronic Table of Contents (United Kingdom)

In order to obtain the electronic structure of leucine (Leu) in aqueous solution, we studied three systems: Leu+7H2O, Leu+8H2O and Leu+9H2O. The results indicated that the system Leu+8H2O was the only choice which was both acceptable and doable: its computational effort was affordable, and it could simulate a main part of the solvent effect on the electronic structure of Leu in solution. Based on the system Leu+8H2O, all-electron, ab initio calculations were performed to construct an equivalent potential of water for the electronic structure of Leu with dipoles. The results showed that the main effect of water on the electronic structure of Leu was raising the occupied states about 0.0824 Ry on average, and broadening the energy gap by 11%. The water effect on the electronic ...

2011-01-01

96

H2/Ar and vacuum annealing effect of ZnO thin films deposited by RF magnetron sputtering system  

British Library Electronic Table of Contents (United Kingdom)

The properties of ZnO films were investigated as functions of annealing temperatures in H2/Ar and vacuum. The resistivities and mobilities of ZnO films decreased with increase of annealing temperatures in vacuum and H2/Ar ambients. However, the carrier densities of ZnO films increased with increase of annealing temperatures in vacuum and H2/Ar ambients. The resistivities of ZnO2 films annealed at 300degreeC were 2186cm and 798cm in H2/Ar and vacuum ambients, respectively. The resistivities of ZnO films annealed in vacuum and H2/Ar ambients at 600degreeC were similar with 0.040cm and 0.035cm, respectively. The hydrogen donor was more dominant than the oxygen vacancy or Zn interstitial donor in ZnO films annealed in ambient H2/Ar at low ...

2010-01-01

97

Radiation Chemistry of Aqueous Solutions Related to Nuclear Reactor Systems and Spent Fuel Management  

International Nuclear Information System (INIS)

In this thesis the rate constants for a number of radical reactions in aqueous solution have been studied in a wide temperature range. The reactions of H with H_2O_2, OH and HO_2 and the reactions of HO_2 with OH, Fe"2"+ and Cu"2"+ have been studied. For each reaction rate constants have been determined as a function of temperature using the technique of high temperature, high pressure (HTP) pulse radiolysis. The rate constants were obtained by fitting a kinetic computer model to the experimental data. From an Arrhenius plot the activation energy of each reaction was determined. The data determined in this way are important for modeling of radiolysis in nuclear light water reactors. A previously developed model for calculation of the effect of water radiolysis products on oxidation and dissolution of spent nuclear fuel has been improved. In the new model, called TraRaMo, simultaneous transport by diffusion and chemical ...

2003-01-01

98

Phase separation in H2O:N2 mixture - molecular dynamics simulations using atomistic force fields  

Energy Technology Data Exchange (ETDEWEB)

A class II atomistic force field with Lennard-Jones 6-9 nonbond interactions is used to investigate equations of state (EOS) for important high explosive detonation products N{sub 2} and H{sub 2}O in the temperature range 700-2500 K and pressure range 0.1-10 GPa. A standard 6th order parameter-mixing scheme is then employed to study a 2:1 (molar) H{sub 2}O:N{sub 2} mixture, to investigate in particular the possibility of phase-separation under detonation conditions. The simulations demonstrate several important results, including: (1) the accuracy of computed EOS for both N{sub 2} and H{sub 2}O over the entire range of temperature and pressure considered; (2) accurate mixing-demixing phase boundary as compared to experimental data; and (3) the departure of mixing free energy from that predicted by ideal mixing law. The results provide comparison and guidance to state-of-the-art chemical kinetic models.

2006-09-25

99

Measurement of "1"0"1Tc Half-Life  

International Nuclear Information System (INIS)

75 mg (NH_4)_6Mo_7O_24 #centre dot# 4H_2O solution was irradiated for 20 min in miniature neutron source reactor (MNSR) and cooled for 12 min. In the conditions of 0.8 mol/L HNO_3, phase ratio 1:1, the solution of "1"0"1Tc sample was extracted twice with #alpha#-benzoin oxime/ethyl acetate phase to remove "1"0"1Mo and a radiochemically pure and carrier-free "1"0"1Tc product was obtained. The half-life of "1"0"1Tc was accurately measured with a HPGe #gamma#-detector by following 306.8 keV #gamma#-ray about 150 min, and processed the data by three methods, R-value method, iterative method and translation method. Five parallel measurments gave a half-life (14.02 #+-# 0.01) min (n=5) for "1"0"1Tc. (authors)

2009-11-01

100

Evaluation of value for hydrogen release from high-level liquid waste. 4. Hydrogen release rate for #gamma#-ray radiolysis of simulated purex waste solutions  

International Nuclear Information System (INIS)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).

1997-01-01

101

Development of a process for the disposal of evaporation residues from NPP by precipitation/flocculation and solidification of the precipitation products. Final report  

International Nuclear Information System (INIS)

To reduce the volume of radioactive wastes after evaporation, activity carriers can be separated from the inactive salt load. Boric acid separation from PWR concentrates was considered a preliminary stage for nuclide precipitation. In connection with the precipitation process, the reaction conditions for boric acid separation were determined by bench-scale experiments. After evaluating the known purification processes, crystallization was suggested as a practicable method. After inactive bench-scale experiments, mixed crystal formation with iron hexacyanoferrate for Cs removal was chosen. The disturbing effect of the complexing agents was neutralized by a pre-dose of iron-III-salts. By specifying the precipitation conditions, for Cs-134 an activity separation from 3,0 E + 06 Bg/l to 1,9 E + 02 Bg/l, and for Cs-137 from 5,9 E + 06 Bg/l to 1,2 E + 02 Bg/l was achieved. Accordingly, the decontamination factor for Cs-134 was 16000, and for Cs-137 48000. For the precipitation of ...

102

Supply of medium and small hydropower equipment  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a brief account of Lingling Hydroelectric Power Equipment General Works, the capacity of equipment production, the organization body, the quality assurance system and supervision of government department on its product quality.

1995-07-01

103

In Silico Atomic Tracing by Substrate-Product Relationships in Escherichia coli Intermediary Metabolism  

UK PubMed Central (United Kingdom)

We present a software system that computationally reproduces biochemical radioisotope-tracer experiments. It consists of three main components: A mapping database of substrate-product atomic correspondents...Full Text Available

2003-11-01

104

Determining insoluble impurities in spent sulfuric acid from the production of synthetic alcohols  

Energy Technology Data Exchange (ETDEWEB)

Ammonium sulfate is produced from spent sulfuric acid from the production of alcohols. Certain mineral and organic impurities exist in the sulfuric acid that impair the quality of the ammonium sulfate. A detailed method for the chemical analysis for the impurities is presented.

1983-01-01

105

Advanced glycation end-products in senile diabetic and non-diabetic patients with cardiovascular complications  

UK PubMed Central (United Kingdom)

Advanced glycation end products (AGEs) have been reported to contribute to aging and cardiovascular complications. In the present study, the immunoreactivity of AGEs in human serum samples of healthy...Full Text Available

2008-12-01

106

High efficiency power production from biomass and waste  

Energy Technology Data Exchange (ETDEWEB)

Two-stage gasification allows power production from biomass and waste with high efficiency. The process involves pyrolysis at about 550C followed by heating of the pyrolysis gas to about 1300C in order to crack hydrocarbons and obtain syngas, a mixture of H2, CO, H2O and CO2. The second stage produces soot as unwanted by-product. Experimental results are reported on the suppression of soot formation in the second stage for two different fuels: beech wood pellets and Rofire pellets, made from rejects of paper recycling. Syngas obtained from these two fuels and from an industrial waste fuel has been cleaned and fed to a commercial SOFC stack for 250 hours in total. The SOFC stack showed comparable performance on real and synthetic syngas and no signs of accelerated degradation in performance over these tests. The experimental results have been used for the design ...

2008-11-15

107

Semi-empirical calculation of air-broadened half-widths and air pressure-induced frequency shifts of water-vapor absorption lines  

International Nuclear Information System (INIS)

This paper describes a semi-empirical calculation of the air-broadened half-widths and the air pressure-induced frequency shifts for the H_2"1"6O isotopologue. This semi-empirical calculation is based on fits of several recent high-quality measurements and theoretical calculations to the first-order terms in the expansion of the complex Robert-Bonamy (CRB) equations, which yields a second- and first-order polynomial function of the differences in the upper- and lower-state vibrational quantum numbers for the half-width and line shift, respectively. The aim of this work was to obtain a complete set of air-broadened half-widths and air pressure-induced frequency shifts for transitions of H_2"1"6O present in the HITRAN database from microwave to the visible in order to supplement the observed and calculated values. For around 700 sets of rotational quantum numbers ...

2005-12-01

108

Probing the Early Stages of Low-Mass Star Formation in LDN 1689N: Dust and Water in IRAS 16293-2422A, B, and E  

CERN Document Server

We present deep images of dust continuum emission at 450, 800, and 850 micron of the dark cloud LDN 1689N which harbors the low-mass young stellar objects (YSOs) IRAS 16293-2422A and B (I16293A and I16293B) and the cold prestellar object I16293E. Toward the positions of I16293A and E we also obtained spectra of CO-isotopomers and deep submillimeter observations of chemically related molecules with high critical densities. To I16293A we report the detection of the HDO 1_01 - 0_00 and H2O 1_10 - 1_01 ground-state transitions as broad self-reversed emission profiles with narrow absorption, and a tentative detection of H2D+ 1_10 - 1_11. To I16293E we detect weak emission of subthermally excited HDO 1_01 - 0_00. Based on this set of submillimeter continuum and line data we model the envelopes around I16293A and E. The density and velocity structure of I16293A is fit by an inside-out ...

2004-01-01

109

Adsorption and dissociation of water on the (0001) surface of double hexagonal close packed americium  

International Nuclear Information System (INIS)

Ab initio total energy calculations within the framework of density functional theory have been performed for water molecule adsorption on the (0001) surface of double hexagonal packed americium using a full-potential all-electron linearized augmented plane wave plus local orbitals method (FP-L/APW+lo). Subsequent partial dissociation (OH+H) and complete dissociation (H+O+H) of the water molecule have been examined. The completely dissociated H+O+H configuration exhibit the strongest binding with the surface (3.35 eV), followed by partially dissociated species OH+H (2.23 eV), with all molecular H_2O configurations showing weak physisorption (0.366 eV). For molecular adsorptions, the flat lying orientation of the water molecule if found to be more favorable for majority of the cases. In the case of partial dissociation (OH+H), the vertical orientation of OH molecule with O facing the surface adsorbed at ...

2009-06-01

110

A combinatorial library of micro-topographies and chemical compositions for tailored surface wettability  

Energy Technology Data Exchange (ETDEWEB)

Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X = 1 {mu}m and an intermediate inter-pillar gap size of Y = 4 {mu}m with superhydrophobic CAs over 170 . Surface analysis with X-ray ...

2011-06-15

111

Gasoline from coal: the pioneering South African experience  

Energy Technology Data Exchange (ETDEWEB)

The fact that South Africa had no commercially significant deposits of crude oil necessitated the early development of production of gasoline from coal which was present in abundance in low to medium grade in thick seams, the development of the process since the early 1950s is discussed. Both the Fischer Tropsch and Lurgi processes are used, and three large plants named Sasol One, Two, and Three have been completed. A flow diagram for the Lurgi process as used in these plants is included. Typical products and their properties resulting from the Sasol-type Synthol operation are presented in tabular form. Marketing considerations and economics of production of the Sasol products are discussed briefly. (BLM)

1982-03-01

112

Gasoline from coal: the pioneering South African experience  

Science.gov (United States)

The fact that South Africa had no commercially significant deposits of crude oil necessitated the early development of production of gasoline from coal which was present in abundance in low to medium grade in thick seams, the development of the process since the early 1950s is discussed. Both the Fischer Tropsch and Lurgi processes are used, and three large plants named Sasol One, Two, and Three have been completed. A flow diagram for the Lurgi process as used in these plants is included. Typical products and their properties resulting from the Sasol-type Synthol operation are presented in tabular form. Marketing considerations and economics of production of the Sasol products are discussed briefly. (BLM)

1982-03-01

113

Tri-Service DoD Partnership Delivers Standard Product to ...  

Science.gov (United States)

... This coordinated proposal was presented to the Threat System Working Group (TSWG) (then called the Threat System Investment Working Group ...

2011-05-14

114

Nomographs estite floating-roof tank evaporation  

Energy Technology Data Exchange (ETDEWEB)

Nomographs are presented that estimate the evaporation loss from external floating-roof tanks using tank diameter, type of seal, product vapor pressure, and wind velocity.

1986-01-27

115

Natural gas annual 1996  

Energy Technology Data Exchange (ETDEWEB)

This document provides information on the supply and disposition of natural gas to a wide audience. The 1996 data are presented in a sequence that follows natural gas from it`s production to it`s end use.

1997-09-01

116

Industrial emissions of 1,3-butadiene.  

UK PubMed Central (United Kingdom)

Sources of industrial emissions of 1,3-butadiene are discussed both by process (production, consumers) and type (equipment leaks, point sources). Quantification of the emissions are presented, as reported...Full Text Available

1990-06-01

117

Gas Exchange of Algae  

UK PubMed Central (United Kingdom)

The oxygen production of a photosynthetic gas exchanger containing Chlorella pyrenoidosa (1% packed cell volume) was measured when various concentrations of carbon dioxide were present...Full Text Available

1967-05-01

118

Detecting and Genotyping Escherichia coli O157:H7 using multiplexed PCR and nucleic acid microarrays  

Energy Technology Data Exchange (ETDEWEB)

Rapid detection and characterization of food borne pathogens such as Escherichia coli O157:H7 is crucial for epidemiological investigations and food safety surveillance. As an alternative to conventional technologies, we examined the sensitivity and specificity of nucleic acid microarrays for detecting and genotyping E. coli O157:H7. The array was composed of oligonucleotide probes (25-30 mer) complementary to four virulence loci (intimin, Shiga-like toxins I and II, and hemolysin A). Target DNA was amplified from whole cells or from purified DNA via single or multiplexed polymerase chain reaction (PCR), and PCR products were hybridized to the array without further modification or purification. The array was 32-fold more sensitive than gel electrophoresis and capable of detecting amplification products from < 1 cell equivalent of genomic DNA (1 fg). Immunomagnetic capture, PCR and a microarray were subsequently used to detect 55 CFU ml-1 ...

2000-12-01

119

Indirect liquefaction  

Energy Technology Data Exchange (ETDEWEB)

Research programs, presented at the contractor's review meeting on indirect liquefaction, are presented on the following topics: oxygenates (methanol) synthesis; Fischer-Tropsch synthesis; product upgrading; and process support engineering evaluations. A total of 18 reports are included. Individual projects are processed separately for the data bases. (CBS)

1989-01-01

120

Precipitation-induced runoff and leaching from milled peat mining mires by peat types: A comparative method for estimating the loading of water bodies during peat production  

Energy Technology Data Exchange (ETDEWEB)

Finland has some 10 million hectares of peatland, accounting for almost a third of its total area. Macroclimatic conditions have varied in the course of the Holocene growth and development of this peatland, and with them the habitats of the peat-forming plants. Temperatures and moisture conditions have played a significant role in determining the dominant species of mire plants growing there at any particular time, the resulting mire types and the accumulation and deposition of plant remains to form the peat. While in a natural state the mires of Finland have functioned as carbon dioxide sinks throughout the post-glacial period, but the ditching of peatland for forestry and agriculture, amounting to some 5,7 million hectares in Finland, has affected their water balance, especially over the last hundred years, and has thereby altered the quantity and species composition of the mire vegetation. The invasion of trees and woody plants to replace the typical mire plants following ditching ...

2007-07-01

121

Tribological and corrosion testing of surface engineered surgical grade CoCrMo alloy  

British Library Electronic Table of Contents (United Kingdom)

One of the main causes of hip prostheses failure is the premature wear of its components. Wear of metal-on-metal joints is a concern due to the toxicity and biological reaction of wear debris and metallic corrosion. The main aim of the present study was to investigate the tribological and corrosion behavior of surface engineering CoCrMo alloy. Different surface conditions were obtained on surgical grade wrought CoCrMo alloy: plasma nitrided (520^oC by 7h at gas mixture of 10% N2+90% H2), PVD coated (monolayer CrN and multilayer (TiN/CrN)x3) and modified using duplex surface engineering technology (a combination of the two previous approaches: plasma nitriding followed by plasma assisted PVD). Surfaces were characterized using scanning electron microscopy, nanoindentation, AFM and scratch t...

2011-01-01

122

The non-linear fitting method to analyze the measured M-S plots of bipolar passive films  

International Nuclear Information System (INIS)

Mott-Schottky (M-S) analysis is an effective approach to investigate the electronic property of passive films of metals, and it is well suitable for the passive film with single space charge capacitance. But there is no proper method to analyze the Csc-2 vs. Vm plots of passive films with several space charge capacitances in series connection, such as bipolar passive films. In this paper, the relationship between the space charge capacitance of the bipolar passive film and the applied potential was deduced and the features of corresponding plots were given out simultaneously. Accordingly, a non-linear fitting method was presented to analyze the Csc-2 vs. Vm plots of bipolar passive films. Then the method was used to study the semiconductor characteristics of bipolar passive films formed on the surface of Nickel base alloy after being corroded in the environments with high temperatures and high partial pressures of H2S/CO2. ...

2010-02-28

123

The influence of active screen plasma nitriding parameters on corrosion behavior of a low-alloy steel  

International Nuclear Information System (INIS)

This work presents a comparative study of low-alloy steel nitriding for different possible techniques. Active screen plasma nitriding (ASPN) is a successful surface modification method that has many advantages over the conventional DC plasma nitriding (CPN). The corrosion behavior of 30CrNiMo8 low-alloy steel has been examined using anodic polarization tests in 3.5% NaCl solution under varying conditions of ASPN and CPN processes. The process variables included active screen setup parameters, treatment temperature (550 and 580 deg. C), gas mixture (25/75 and 75/25 of N_2/H_2) and treatment time (5 and 10 h) in 500 Pa pressure. The structure and phases composition of the compound layer was studied by X-ray diffraction (XRD), microhardness tests, optical microscopy and scanning electron microscopy (SEM). It was observed that ASPN treated samples surface enhanced corrosion resistance while the temperature and/or hole size of ...

2009-09-18

124

Study of passive films formed on stainless steel surfaces, using Auger spectroscopy  

International Nuclear Information System (INIS)

This paper deals with the characterization of passive films formed on stainless steel (26% Cr and 0 to 3%Mo). The influence of the applied passivation potential and the effect of molybdenum additions to steel upon the composition profiles of passive films formed in an aqueous NaCl solution (3.5% at pH 2.5) are studied. The technique involved is Auger electron spectroscopy combined with ion sputtering. Some electrochemical techniques have been used in conjunction. A quantitative approach of the Auger spectra during the progressive removal of the passive film is described. The peak-to-peak height of the Auger lines are treated in order to yield the atomic fraction of the various elements present in a given subsurface layer. The analytical study of the film by electron spectroscopy indicates that molybdenum plays a part at the metal-oxide interface where this element acts on the chromium diffusion process. This phenomenon, ...

1975-01-01

125

Multilayered Nano-Microcomposite Ti-Al-N/TiN/Al_2O_3 Coatings. Their Structure and Properties  

International Nuclear Information System (INIS)

This paper presents the first results on formation and study of structure and properties of micro- and nanocomposite combined coatings. By means of modeling the deposition processes (deposition conditions, current density-discharge, plasma composition and density, voltage) we formed the three-layer nanocomposite coatings of Ti-Al-N/Ti-N/Al_2O_3. The coating composition, structure and properties were studied using physical and nuclear-physical methods. The Rutherford proton and helium ion backscattering, scanning electron microscopy with microanalysis, grazing incidence X-ray diffraction, as well as nanohardness tests (hardness) were used. Measurements of wear resistance and corrosion resistance in NaCl, HCl and H_2SO_4 solutions were also performed. For testing mechanical properties such characteristics of layered structures as hardness H, elastic modulus E: H"3/E"2 etc. were measured. It is demonstrated that the formed ...

2011-07-01

126

Heat capacities between 1.5 and 16 K and superconductivity of V/H and Nb/H alloys  

International Nuclear Information System (INIS)

Molar heat capacities have been measured for VHsub(n) and NbHsub(n) with n up to 1.93 at temperatures between 1.5 and 16 K. The height of the peak in plots of the electronic specific heat, indicating superconductivity, diminishes with increasing hydrogen content in the #alpha# + #beta# two-phase region, and can be taken as a measure of the fractional amount of #alpha#-phase present (lever-rule). In NbHsub(n) accordingly, the two-phase region presumably extends up to n = approximately 0.9 at helium temperatures. No hydride phase, including VH_2 and NbH_2, showed superconductivity above 1.5 K. The measured #gamma#-coefficients of the V/H-alloys agree with APW band-structure calculations for V metal in the range 5 =< nsub(e) =< 7 of band electron concentration. They coincide with the #gamma#-coefficients of V/Cr-alloys reported in the literature. Hence VHsub(n) represents another example of the 'shifting bands' concept ...

1977-05-01

127

Facile synthesis of additive-assisted nano goethite powder and its application for fluoride remediation  

Energy Technology Data Exchange (ETDEWEB)

The present article describes a novel synthesis route for nano-sized goethite ({alpha}-FeOOH) using hydrazine sulphate as an additive. The X-ray diffraction (XRD) peaks of synthesized powder matched well with those of {alpha}-FeOOH. Transmission electron microscopy (TEM) showed the particles of irregular shape in the range of 1-10 nm. Batch adsorption experiments for fluoride uptake were performed to study the influence of various experimental parameters such as contact time (10 min to 7 h), initial fluoride concentration (10-150 mg L{sup -1}), pH (2-11.6) and the presence of competing anions. The time data fitted well to pseudo-second-order kinetic model. The fluoride removal passed through broad maxima in pH ranges of 6-8. High adsorption capacity of 59 mg g{sup -1} goethite was obtained. The isothermic data fitted well to Freundlich model. The presence of other ions namely chloride and sulphate adversely affected ...

2010-02-15

128

Electricity in Lebanon: a century report (1885-1994)  

International Nuclear Information System (INIS)

The document reports the status of the 'electricity' in Lebanon since 1885 with an emphasis on its present economical situation. Data concerning electric power consumption and distribution as well as the average of rainwater, spring and weather are given. Power plants in Lebanon, the production of electric power and its consumption are described. A quantitative analysis of specifications of power plants and their annual and monthly production of electric power, the distribution of electricity consumption in Lebanon (geographical, annual, monthly) are presented in tables and graphs. An overview of the economical status of the 'electricity' in Lebanon is presented. The evolution of prices charges, hour cuts, damages and the impact of Lebanese wars on the distribution and the consumption of electricity are presented

129

Wind-To-Hydrogen Project: Operational Experience, Performance Testing, and Systems Integration  

Energy Technology Data Exchange (ETDEWEB)

The Wind2H2 system is fully functional and continues to gather performance data. In this report, specifications of the Wind2H2 equipment (electrolyzers, compressor, hydrogen storage tanks, and the hydrogen fueled generator) are summarized. System operational experience and lessons learned are discussed. Valuable operational experience is shared through running, testing, daily operations, and troubleshooting the Wind2H2 system and equipment errors are being logged to help evaluate the reliability of the system.

2009-03-01

130

Renewable energies in France: the main 2001 results; Les energies renouvelables en France: les principaux resultats en 2001  

Energy Technology Data Exchange (ETDEWEB)

This 2001 status on the use of renewable energies in France makes a synthesis of the electric and heat productions of renewable origin. It lists the primary or secondary productions of renewable energies, and details the uses corresponding to each renewable energy production source and their respective satisfaction of consumer's needs (residential, industry and agriculture sectors). A detail statistical status for 1999, 2000 and 2001 is presented in tables. (J.S.)

2002-05-01

131

Floating production and storage vessels - design analysis and operational issues: a handbook produced to accompany the Bentham Technical Training Courses  

Energy Technology Data Exchange (ETDEWEB)

These ten chapters present an overview of floating production, storage and offloading (FPSO) vessels, and examines deep water developments; hydrostatic stability; production, storage and offloading systems; the configuration and structure of flexible risers and umbilicals; the structural and global dynamic analysis of flexible riser and umbilicals; verification of FPSO structural integrity; vessel global loading and rigid body response; environmental loading and vessel response; and mooring systems. (UK)

1998-07-01

132

Development of an experimental installation for short-lived isotopes production in INR linac  

International Nuclear Information System (INIS)

A possibility of short-lived isotopes production in inter-tank section between the first and the second drift tube tanks (20.45 MeV) in INR linac is considered. At the initial stage the main efforts are concentrated on production of fluorine-18 used for positron emission tomography. The results of beam forming calculations, target heating calculations, equipment activation calculations as well as installation configuration and design are presented.

2010-01-01

133

Synthesis and Structural Characterization of a Novel Indium Mercapto Derivative [Clln(SCH2(CO)O)2]2-[(4-MepyH)2]2+  

Science.gov (United States)

The synthesis and structural characterization of a novel In(III) complex is described. The reaction

2004-01-01

134

Symbiotic N2 fixation by legumes growing in pots. 2. Uptake of VN-labelled NO3 , C2H2 reduction and H2 evolution by Trifolium subterraneum L. , Medicago truncatula Gaertn. and Acacia dealbata Link  

Energy Technology Data Exchange (ETDEWEB)

The objectives of this study were to estimate symbiotic nitrogen fixation by two common pasture legumes, Trifolium subterraneum L. and Medicago truncatula Gaertn., and an Australian native legume, Acacia dealbata Link, growing in pots using an indirect isotopic method. This method was also used to calibrate the C2H2 reduction assay of the intact plants. In addition, hydrogen evolution was measured in an attempt to explain the variations in C2H2:N2 ratios between the species. 25 refs.; 1 figure; 4 tabs.

1983-01-01

135

Dynamic response of a PEM fuel cell under reactant gas starvation  

Science.gov (United States)

The fuel cell control problem was studied. Attempts were made to control the output current of the fuel cell by starving it of hydrogen and oxygen. The motivation of this work was to increase efficiency by minimizing waste of fuel. The following findings were obtained: H2 starvation works better than O2 starvation; An optimal H2 to O2 ratio exists for combined H2&O2 starvation; The control scheme for H2&O2 starvation works well for 3 different disturbance tests and at 25 degrees C, 60 degrees C, and 80 degrees C; Fuel cell under reactant starvation is stable for at least 72 hrs.

2005-08-05

136

Durability of Membrane Electrode Assemblies (MEAs) in PEM Fuel ...  

Science.gov (United States)

Proton exchange membrane (PEM) fuel cells are energy sources that have the ... for H2 /02 PEM fuel cells because their catalysts have properties suitable for 0 ...

137

Technology assessment: Chlorine chemistry  

International Nuclear Information System (INIS)

Chlorine is not just one of many chemical feedstocks which is used in a few definitely harmful products like PVC or CFC but is irrelevant in all other respects. Just the opposite is true: There is hardly any product line of the chemical industry that can do without chlorine, from herbicides and pesticides to dyes, plastics, pharmaceuticals, photographic atricles, and cosmetics. Chlorine is not only a key element of chemical production but also an ubiquitous element of everyday life in civilisation. There are even many who would agree that the volume of chlorine production is an indicator of the competitive strength and national wealth of a modern society. By now, however, it has become evident that the unreflected use of chlorine is no longer ecologically acceptable. The consequences of a chlorine phase-out as compared to the continued chlorine production at the ...

138

Production of radioisotopes in the ORNL 86-inch cyclotron  

Energy Technology Data Exchange (ETDEWEB)

The radioisotope production facilities and programs of the 86-Inch Cyclotron are reviewed in this presentation. The 86-Inch Cyclotron is designed to accelerate protons to a maximum energy of 22 MeV for internal targets. These protons are used to bombard metals that are electroplated, potted or soldered to water-cooled plates. Additionally, metals and inorganic compounds are bombarded in water-cooled tube targets. High radioisotope production rates are obtained by beam currents as large as 3 mA. Production rates for /sup 11/C, /sup 57/Co, /sup 67/Ga, /sup 68/Ge, /sup 109/Cd, and other isotopes are presented. The production of /sup 11/C for the carboxyl labeling of amino acids in cooperation with Oak Ridge Associated Universities is discussed. The 86-Inch Cyclotron is used for those programs requiring a larger beam current than is available from commercial ...

1981-04-01

139

PWR FISSION PRODUCT ACTIVITY LEVELS  

Science.gov (United States)

Recent radiochemical investigations of the PWR reactor coolant have corfirmed earlier observations that the level of activities of 33 m Cs/sup 138/, 2.8 hr Kr , and 8.1 day 1/sup 131/ are more than ten times higher than those predicted for the estimated U contamination of the Zircaloy cladding. The present fission product activity levels have not, as yet, presented any problems in the PWR. (W.L.H.)

1958-05-01

140

Efficient operation of equipment at the mine ''Tsentral'naya'' and ways to improve it  

Energy Technology Data Exchange (ETDEWEB)

Results are presented from analyzing indicators for efficient operation of the fleet of production equipment under conditions of the ''Tsentral'naya'' mine of the production association ''Krasnoarmeyskugol'.'' Measures are presented which make it possible to increase the operating efficiency with minimum adjusted outlays.

1980-01-01

141

Developments and potential of radiation processing in the Philippines  

Energy Technology Data Exchange (ETDEWEB)

This paper describes the research and development activities in three areas of radiation processing, namely: food irradiation, medical product sterilization and wood plastic combination. Plans and efforts exerted to acquire a larger gamma source to augment our present 5,000 curie source are discussed. Cost estimates for a radiation facility are presented on the basis of the market potential of food irradiation and medical product sterilization. Existing local industries that can benefit from the adaptation of irradiation technology in their processing requirements are described.

1981-01-01

142

The regional control of the canadian energy production; Le contraste provincial de la production energetique canadienne  

Energy Technology Data Exchange (ETDEWEB)

This document provides information and presents data on the energy situation in many regions of Canada. The first part deals with the petroleum and the bitumen shales of Alberta (reserves, exploitation and production, environmental impacts), the second part discusses with the hydroelectricity choice of Quebec and the 2004 crisis. The nuclear situation of Ontario is presented in the third part (nuclear park, programs, uranium reserves, research and development on Candu reactors), while the fourth part deals with the renewable energies (wind power and biomass). The canadian situation facing the Kyoto protocol is discussed in the last part. (A.L.B.)

2004-12-01

143

Recovery of rare earths from red mud  

International Nuclear Information System (INIS)

The prospect for the recovery of rare earths from red mud, the bauxite tailings from the production of alumina is examined. The Jamaican red mud by far has the higher trace concentrations of lanthanum, cerium, neodymium, and yttrium. Scandium is also present. The dissolution of the rare earth is a major extraction problem because of the large volume of other materials. The recovery processes that have been proposed include the production of co-products such as iron, alumina, and titanium concentrates, with the rare earths going with the titanium. In this paper a critical examination of the possible processes are presented with the recommended research projects to be carried out.

1992-03-01

144

Optimization of mechanical properties of recycled plastic products via optimal processing parameters using the Taguchi method  

British Library Electronic Table of Contents (United Kingdom)

The large amount of plastic products presently produced necessitates recycling and reuse of these non-biodegradable materials. However, the degradation in the mechanical properties of products made from recycled plastic is a major drawback that limits their use. This study aims to improve the mechanical properties of products made from recycled plastic by utilizing the Taguchi optimization method, instead of coupling the products with additives. By adopting L9 Taguchi OA, products made from various compositions of virgin and recycled plastic are produced by injection moulding. Four controllable factors (i.e., melt temperature, packing pressure, injection time, and packing time), each at three levels, are tested to determine the optimal combination of factors and levels in the manufacturing...

2011-01-01

145

Fragrance ingredient labelling in products on sale in the U.K.  

British Library Electronic Table of Contents (United Kingdom)

Summary Background The seventh amendment of the European Union (EU) Cosmetics Directive (March 2005) and the Detergents Regulations of the EU (October 2005) are now legal requirements in Europe. Cosmetic products and detergents must be labelled for 26 individual named fragrances, when present at concentrations of > 10 parts per million (p.p.m.) in leave-on products and > 100 p.p.m. in rinse-off products. Objectives To make an assessment of the exposure pattern to fragrance of the U.K. consumer and to determine the frequency with which the constituent fragrances of fragrance mix I (FM I) and fragrance mix II (FM II) are included in products currently sold in the U.K. Methods A study of perfumed cosmetic and household products available on the shelves of U.K. retailers was carried out in Jan...

2007-01-01

146

Cumulative production of direct photons and leptonic pairs  

International Nuclear Information System (INIS)

Leptonic pair production on nuclei ad EMC-effect are discussed within the frames of the flucton model with scaling distortion. Cumulative production of direct photons and leptonic pairs as a test of the model of hard collisions is considered. The results of calculations of massive leptonic pair production cross sections on nucleus fluctons, caculations of the ratio of deuterium and iron structural functions, cross sections of direct photon production on sup(181)Ta nuclei at Esub(p)=400 GeV and cross section of #pi#-meson production in the model of hard collisions are presented. Experimental discovery of direct cumulative photons is concluded to be important for understanding the mechanism of parton hard scattering from nucleus fluctons.

1984-06-19

147

Thermal release of volatile fission products from irradiated nuclear fuel  

International Nuclear Information System (INIS)

An effective procedure for removing _3H, Xe and Kr from irradiated fuels was demonstrated using Shippingport UO"2 fuel. The release characteristics of _3H, Kr, Xe, and I from irradiated nuclear fuel have been determined as a function of temperature and gaseous environment. Vacuum outgassing and a flowing gas stream have been used to vary the gaseous environment. Vacuum outgassing released about 99% of the _3H and 20% of both Kr and Xe within a 3 h at 1500_0C. Similar results were obtained using a carrier gas of He containing 6% H"2. However, a carrier gas containing only He resulted in the release of approximately 80% of the _3H and 99% of both Kr and Xe. These results indicate that the release of these volatile fission products from irradiated nuclear fuel is a function of the chemical composition of the gaseous environment. The rate of tritium release increased with increasing temperature (1100 to 1500_0C) and with the ...

148

Synthesis, crystal structure, spectroscopic and photoluminescence studies of manganese(II), cobalt(II), cadmium(II), zinc(II) and copper(II) complexes with a pyrazole derived Schiff base ligand  

British Library Electronic Table of Contents (United Kingdom)

Varying coordination modes of the Schiff base ligand H"2L [5-methyl-1-H-pyrazole-3-carboxylic acid (1-pyridin-2-yl-ethylidene)-hydrazide] towards different metal centers are reported with the syntheses and characterization of four mononuclear Mn(II), Co(II), Cd(II) and Zn(II) complexes, [Mn(H"2L)(H"2O)"2](ClO"4)"2(MeOH) (1), [Co(H"2L)(NCS)"2] (2), [Cd(H"2L)(H"2O)"2](ClO"4)"2 (3) and [Zn(H"2L)(H"2O)"2](ClO"4)"2 (4), and a binuclear Cu(II) complex, [Cu"2(L)"2](ClO"4)"2 (5). In the complexes 1-4 the neutral ligand serves as a 3N,2O donor where the pyridine ring N, two azomethine N and two carbohydrazine oxygen atoms are coordinatively active, leaving the ...

2011-01-01

149

Sealant Research for solid oxide fuel cells  

International Nuclear Information System (INIS)

The objective of this work is to develop sealing materials for solid oxide fuel cells (SOFCs). A suitable sealant must form strong, dense bonds with SOFC components, be chemically and mechanically compatible with the components, be stable at 1000 degrees C in the operating environment of the SOFC (H_2 and H_2O on the anode side, O_2 on the cathode side), and must be nonconductive.

1992-07-01

150

Novel inorganic hydrogen-bonded crystals with nonlinear optical properties  

International Nuclear Information System (INIS)

Four inorganic hydrogen-bonded crystals with second-order nonlinear properties have been discovered: K_4LiH_3(SO_4)_4, Na_2SeO_4#centre dot#H_2SeO_3#centre dot#H_2O, Cs_1_,_5Li_1_,_5H(SO_4)_2 and NH_4HSeO_4. (author)

2000-01-01

151

HupUV proteins of Rhodobacter capsulatus can bind H2: evidence from the H-D exchange reaction.  

UK PubMed Central (United Kingdom)

The H-D exchange reaction has been measured with the D2-H2O system, for Rhodobacter capsulatus JP91, which lacks the hupSL-encoded hydrogenase, and R. capsulatus BSE16, which lacks the HupUV proteins....Full Text Available

1997-01-01

152

A precise structure redetermination of nickel ammonium sulfate hexahydrate, Ni(H_2O)_6.2NH_4.2SO_4  

International Nuclear Information System (INIS)

The Ni(H_2O)_6 ion is located at an inversion center. Six octahedral water molecules surround the Ni"I"I ion and form hydrogen bonds with the sulfate groups. Each ammonium group binds to the sulfate groups through hydrogen bonds. (orig.).

1994-05-01

153

Effect of hydrogen sulfide on chemical looping of coal-derived synthesis gas over bentonite-supported metal---oxide oxygen carriers  

Science.gov (United States)

The effect of hydrogen sulfide (H2S) on the chemical looping combustion of coal-derived synthesis gas with bentonite-supported metal oxidesssuch as iron oxide, nickel oxide, manganese oxide, and copper oxideswas investigated by thermogravimetric analysis, mass spectrometry, and X-ray photoelectron spectroscopy (XPS). During the reaction with synthesis gas containing H2S, metal-oxide oxygen carriers were first reduced by carbon monoxide and hydrogen, and then interacted with H2S to form metal sulfide, which resulted in a weight gain during the reduction/sulfidation step. The reduced/sulfurized compounds could be regenerated to form sulfur dioxide and oxides during the oxidation reaction with air. The reduction/oxidation capacities of iron oxide and nickel oxide were not affected by the presence of H2S, but both ...

2009-01-01

154

Dodecanuclear rhenium cluster complexes with an interstitial carbon atom: Synthesis, structures and properties of two new compounds K6[Re12CS17(OH)6]?4H2O and Na12Re12CS17(SO3)6?48.5H2O  

British Library Electronic Table of Contents (United Kingdom)

The dodecanuclear rhenium anionic complex with terminal hydroxo ligands [Re12CS17(OH)6]6? was obtained by the reaction of K6[Re12CS17(CN)6]?20H2O with molten KOH at 300 ?C. The cluster complex was crystallized as a potassium salt from aqueous solution. The reaction between K6[Re12CS17(OH)6]?4H2O and Na2S2O4 in water under reflux results in the formation of the complex Na12[Re12CS17(SO3)6]?48.5H2O. Both new compounds were characterized by single-crystal X-ray diffraction, elemental analyses and IR spectroscopy. The electronic structure of [Re12CS17(OH)6]6? was also elucidated by DFT calculation

2010-01-01

155

An analysis of tanker-based floating production systems for small offshore fields  

Energy Technology Data Exchange (ETDEWEB)

A historical review of floating production storage and offloading (FPSO) systems for marginal fields is presented. The areas in which such systems are operating, ranges of model tests, and current applicability of mooring systems are reviewed to present capabilities of these concepts. Limitations are reviewed to assess the applicability of these concepts to similar sites. Consideration of processing operations on floating vessels are identified. Particularly, the effects of vessel motion on the processing equipment, gas disposal, and crude offloading are addressed. It will be shown that operations are becoming well understood and routine. Future problem areas and solutions under development are identified. Specific examples are cited and design refinements are noted. While various floating production systems have been in operation for only a few years, their potential for solving the problems of ...

1982-08-01

156

Recent research efforts in the area of biotechnology for fuels and chemicals: Poster session papers  

Energy Technology Data Exchange (ETDEWEB)

This report presents research presented at the poster session of the Symposium covering a wide spectrum of current biotechnological research activities. Research focused mostly on ethanol production and methane generation from biomass material via microbial processing, as well as on enhanced hydrogen yield from algae. Several of the posters dealt with the pretreatment of cellulosic materials, and enzyme production/characterization, while a good number of papers displayed research efforts on bioremediation, photosynthesis, production of various useful chemicals from biomass by bioprocessing, and on other miscellaneous subjects. One of the papers treated a very interesting topic of cellulose-cellulase complexes. Many of the poster papers are included in this volume, and a synopsis of all the poster/papers presented is the subject of this article.

1992-01-01

157

Leaching of zinc sulfide by Thiobacillus ferrooxidans: Bacterial oxidation of the sulfur product layer increases the rate of zinc sulfide dissolution at high concentrations of ferrous ions  

Energy Technology Data Exchange (ETDEWEB)

This paper reports the results of leaching experiments conducted with and without Thiobacillus ferroxidans at the same conditions in solution. The extent of leaching of ZnS with Bacteria is significantly higher than that without bacteria at high concentrations of ferrous ions. A porous layer of elemental sulfur is present on the surfaces of the chemically leached particles, which no sulfur is present on the surfaces of the bacterially leached particles. The analysis of the data using the shrinking-core model shows that the chemical leaching of ZnS is limited by the diffusion of ferrous ions through the sulfur product layer at high concentrations of ferrous ions. The analysis of the data shows that diffusion through the product layer does not limit the rate of dissolution when bacteria are present. This suggests that the action of T.ferroxidans in oxidizing the sulfur formed on the ...

1999-12-01

158

Chemical products and industrial materials; Produits chimiques et materiaux industriels  

Energy Technology Data Exchange (ETDEWEB)

A compilation of all universities, industrial and governmental agencies in Quebec which are actively involved in research and development of chemical products and industrial materials derived from biomass products, was presented. Each entry presented in a standard format that included a description of the major research activities of the university or agency, the principal technologies used in the research, available research and analytical equipment, a description of the research personnel, names, and addresses of contact persons for the agency or university. Thirty entries were presented. These covered a wide diversity of activities including biotechnological research such as genetic manipulations, bioconversion, fermentation, enzymatic hydrolysis and physico-chemical applications such as bleaching, de-inking, purification and synthesis. tabs.

1995-12-01

159

Sialon sintering product excellent in liquid sodium corrosion resistance  

International Nuclear Information System (INIS)

A sialon sintering product of the present invention comprises #beta#'-sialon grains and less than 2vol% of a grain boundary phase, and a relative density of the sintering product is greater than 98%. It exhibits a high temperature strength of greater than 500Mpa at 650degC and shows such high corrosion resistances that the reduction of the volume due to corrosion is less than 0.5mg/cm"2 in a liquid sodium immersion test, and the corrosion of the grain boundary is not observed. Accordingly, there can be provided a sialon sintering product excellent in corrosion resistance in a liquid sodium circumstance while keeping the high temperature strength as an excellent characteristic of the sialon sintering product. (T.M.).

1995-04-19

160

Occurrence of metals in petroleum and hydrocarbon products and methods for their determination  

Energy Technology Data Exchange (ETDEWEB)

Petroleum, known to be a source of a vast variety of organic compounds, is also a depository of valuable mineral components. Vanadium and nickel are the most important metal components of crude petroleum, with their concentrations reaching a few tenths of a percent. Their percentage increases 2- to 5-fold in the hydrocarbon products. The vanadium content in processed petroleum products is given. Therefore, the extraction of metals from petroleum is becoming an increasing important task. At present, there is no petroleum processing technology aimed solely at obtaining organic components. The occurrence of metals and other trace elements in petroleum and hydrocarbon products is discussed on the basis of available literature and experimental data. Techniques for isolating metals from petroleum and hydrocarbon products and their quantitative determination are considered.

1995-07-01

161

Collaborative e-product development and product innovation in a demand-driven network: the moderating role of eCRM  

British Library Electronic Table of Contents (United Kingdom)

Customer relationships, product development, data integration and demand-driven supply chains are key concepts for companies that wish to remain competitive in today?s global economy. To address this important information management issue, the present study examines how, within a demand-driven network context, an eCRM can influence the interorganizational product development process between a manufacturer and its key customers. The theoretical model, built on research related to a technology assimilation model based on Fichman?s (2000) work, was tested on data from 104 manufacturers in the wireless equipment sector. The results show that the adoption of an eCRM does not moderate the relationship between collaborative e-product development involving a manufacturer and its key customers and ...

2009-01-01

162

Predicting Knot and Catenane Type of Products of Site-specific Recombination on Twist Knot Substrates  

CERN Document Server

Site-specific recombination is an important cellular process that yields a variety of knotted and catenated DNA products on supercoiled circular DNA. Twist knots are some of the most common conformations of these products. They are also one of the simplest families of knots and catenanes. Yet, our systematic understanding of their implication in DNA and important cellular processes like site-specific recombination is very limited. Here we present a topological model of site-specific recombination characterising all possible products of site-specific recombination on twist knot substrates, extending previous work of Buck and Flapan. We illustrate how to use our model to examine previously uncharacterized experimental data. We show how our model can help determine the sequence of products in multiple rounds of processive recombination and distinguish between ...

2010-01-01

163

Herschel observations in the ultracompact HII region Mon R2: Water in dense Photon-dominated regions (PDRs)  

CERN Document Server

Mon R2, at a distance of 830 pc, is the only ultracompact HII region (UC HII) where the photon-dominated region (PDR) between the ionized gas and the molecular cloud can be resolved with Herschel. HIFI observations of the abundant compounds 13CO, C18O, o-H2-18O, HCO+, CS, CH, and NH have been used to derive the physical and chemical conditions in the PDR, in particular the water abundance. The 13CO, C18O, o-H2-18O, HCO+ and CS observations are well described assuming that the emission is coming from a dense (n=5E6 cm-3, N(H2)>1E22 cm-2) layer of molecular gas around the UC HII. Based on our o-H2-18O observations, we estimate an o-H2O abundance of ~2E-8. This is the average ortho-water abundance in the PDR. Additional H2-18O and/or ...

2010-01-01

164

Toward the production of 50 000 tonnes of low-carbon steel sheet for the LHC superconducting dipole and quadrupole magnets  

CERN Document Server

A total of 50 000 tonnes of low-carbon steel sheet has been ordered for the LHC main magnets. After three years of production, about 10 000 tonnes of steel sheet have been produced by Cockerill-Sambre Groupe Usinor. This paper gives a summary of the manufacturing process and improvements implemented as well as an overview of the difficulties encountered during this production. Preliminary statistics obtained for the mechanical and magnetic steel properties are presented. (6 refs).

2002-01-01

165

NewProductsAndServices  

Wastenet

... John Cannaday and Ken Weddle present the framework for a Product Design Engineering project (http://engineering.dartmouth.edu/~teps/images/ProductDesign.pdf) for high school students which may have relevance at a more advanced level. David Price has created a Mechanical Engineering Design (http://www.soton.ac.uk/~cds/) site containing engineering design notes. The Virtual Reality Engineering Library Home Page at the University of Bristol (http://www.dig.bris.ac.uk/virtual_lib/) is a library ...

166

More Polish coal mines needed  

Science.gov (United States)

The economy of Poland depends to a large extent upon the exploitation of its vast rich coal reserves for which new mines will have to be sunk and existing mines modernized. Two avenues of coal conversion are being followed. Both involve hydrogenation but one is based on solvent extraction of coal and the other on its pyrolysis. At present large scale established methods of chemical treatment are those which involve the production of coke, production of town-gas, production of synthesis gas and partial oxydation. Total weight amounts to 21,000,000 tons.

1977-11-01

167

Measurement of the inclusive Z production cross section with the CMS detector  

CERN Document Server

First measurements of inclusive Z production cross sections in muon and electron decay channels at 7 TeV are presented for proton-proton collisions in the Compact Muon Solenoid (CMS) detector at the Large Hadron Collider (LHC). The comparison of the kinematic quantities as well as the studies of selection efficiencies demonstrate a good agreement between simulated events and current data. The measured inclusive cross section for Z($\\gamma^{*}$) production agrees with NNLO QCD cross section calculations and current parton distribution functions.

2010-01-01

168

Fungal laccases: production, function, and applications in food processing.  

Science.gov (United States)

Laccases are increasingly being used in food industry for production of cost-effective and healthy foods. To sustain this trend widespread availability of laccase and efficient production systems have to be developed. The present paper delineate the recent developments that have taken place in understanding the role of laccase action, efforts in overexpression of laccase in heterologous systems, and various cultivation techniques that have been developed to efficiently produce laccase at the industrial scale. The role of laccase in different food industries, particularly the recent developments in laccase application for food processing, is discussed. PMID:21048859

2010-09-21

169

Correlation-based spectral clustering for flexible process monitoring  

British Library Electronic Table of Contents (United Kingdom)

The individuality of production devices should be taken into account when statistical models are designed for parallelized devices. In the present work, a new clustering method, referred to as NC-spectral clustering, is proposed for discriminating the individuality of production devices. The key idea is to classify samples according to the differences of the correlation among measured variables, since the individuality of production devices is expressed by the correlation. In the proposed NC-spectral clustering, the nearest correlation (NC) method and spectral clustering are integrated. The NC method generates the weighted graph that expresses the correlation-based similarities between samples, and the constructed graph is partitioned by spectral clustering. A new statistical process monit...

2011-01-01

170

Use of hydrolyzed polyacrylonitrile for limiting the influxes of water at the Sokolovgoroskiy field  

Energy Technology Data Exchange (ETDEWEB)

A formula and technology are presented for the preparation of a hydrolyzed polyacrylonitrile (gipane) from the wastes of chemical production, analysis of the results of working to use them to insulate influxes of water in the extracting wells of the Sokolovogorskiy field.

1980-01-01

171

Thermal plasma process for recovering monomers and high value carbons from polymeric materials  

Energy Technology Data Exchange (ETDEWEB)

The present invention relates to a method of recycling polymeric waste products into monomers and high value forms of carbon by pyrolytic conversion using an induction coupled RF plasma heated reactor.

2002-01-01

172

Quantification of physical and biological uncertainty in the simulation of the yield of a tropical crop using present-day and doubled CO2 climates  

UK PubMed Central (United Kingdom)

The impacts of climate change on crop productivity are often assessed using simulations from a numerical climate model as an input to a crop simulation model. The precision of these predictions reflects...Full Text Available

2005-11-29

173

Production of a fecal mutagen by Bacteroides spp.  

UK PubMed Central (United Kingdom)

Forty species of anaerobes were screened for the ability to produce an ether-extractable mutagen which is present in the feces of 15 to 20% of individuals in populations at high risk for colon cancer....Full Text Available

1982-09-01

174

Numerical Weather Prediction Activities Report.  

Science.gov (United States)

This report presents a summary of highlights of the year 1978. It then discusses: Research and development in numerical analysis and prediction systems; Techniques, development and application of new products; Analysis-forecast systems in operation use du...

1978-01-01

175

Increased Ethanol Productivity in Xylose-Utilizing Saccharomyces cerevisiae via a Randomly Mutagenized Xylose Reductase?  

UK PubMed Central (United Kingdom)

Baker's yeast (Saccharomyces cerevisiae) has been genetically engineered to ferment the pentose sugar xylose present in lignocellulose biomass. One of the reactions controlling the...Full Text Available

2010-12-01

176

Harnessing the geothermal resources of sedimentary basins for electricity production  

Science.gov (United States)

Use of geothermal resources for generating electricity is briefly analyzed. Results obtained from optimization of the thermodynamic cycle implemented in the secondary coolant circuit of a binary geothermal power station and the parameters of its primary heat carrier circuit are presented.

2011-02-01

177

Formation, Repair, and Genotoxic Properties of Bulky DNA Adducts Formed from Tobacco-Specific Nitrosamines  

UK PubMed Central (United Kingdom)

4-(Methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) and N′-nitrosonornicotine (NNN) are tobacco-specific nitrosamines present in tobacco products and smoke. Both compounds...Full Text Available

178

Effect of Length of Time before Incorporation on Survival of Pathogenic Bacteria Present in Livestock Wastes Applied to Agricultural Soil  

UK PubMed Central (United Kingdom)

In response to reports that the contamination of food can occur during the on-farm primary phase of food production, we report data that describes a possible cost-effective intervention measure. The...Full Text Available

2004-09-01

179

Application of gamma radiation  

International Nuclear Information System (INIS)

Described and discussed in this paper are radiation processes and their advantages over the conventional techniques. Radiation sterilization of medical products, food irradiation, wood plastic composites, and radiation treatment of sewage and waste waters are presented. The Philippine experience in using these technologies, its problems and barriers are also given. (ELC).

1985-12-10

180

Synthesis and PET imaging of the benzodiazepine receptor tracer [N-methyl-"1"1C]iomazenil  

International Nuclear Information System (INIS)

The central benzodiazepine receptor tracer [N-methyl-"1"1C]iomazenil (Ro 16-0154) was synthesized by alkylation of the desmethyl precursor noriomazenil with ["1"1C]methyl iodide. The ["1"1C]CH_3I (prepared by reduction of ["1"1C]CO_2 with LiAlH_4 followed by reaction with HI) was reacted with noriomazenil inN,N -dimethylformamide and Bu_4N"+OH"- for 1 min at 80 deg. C and purified by HPLC (C_1_8, 34% CH_3CN/H_2O, 7 mL/min). The product was obtained with synthesis time 35 #+-# 5 min (mean #+-# SD, n = 7), radiochemical yield (EOB) 36 #+-# 16%, radiochemical purity 99 #+-# 1%, and specific activity 5100 #+-# 2800 mCi/#mu#mol. Absorbed radiation doses were calculated from previously acquired human biodistribution data. The urinary bladder wall received the highest dose (0.099 mGy/MBq) for 4.8 h voiding interval and the effective dose equivalent was 0.015 mSv/MBq. After i.v. injection of ["1"1C]iomazenil in an adult baboon or ...

1995-07-01

181

Production of high-q ions by laser bombardment method  

International Nuclear Information System (INIS)

The expanding plasma produced when an intense pulse of laser radiation is focused in vacuum onto a solid target has been used as a source of highly stripped ions for collision cross-section measurements. Usable fluxes of carbon nuclei at energies of a few hundred eV/charge have been obtained by irradiation of graphite with pulses of CO"2 laser radiation at a focused power density of 3 x 10_1_0 W/cm_2. Bombardment of aluminum and iron targets at comparable power levels have yielded ions of maximum charges of 9 and 16 respectively. A time-of-flight apparatus has been constructed to utilize the laser source for measurement of electron capture cross sections for highly stripped ions in gases at energies in the few hundred eV/charge range. Apertures collimate an ion beam from the plasma blowoff, and an electrostatic analyzer selects ions from the expanding plasma which have the same energy per charge. The beam is directed through a gas target cell, charge anlyzed once more by deceleration, ...

1981-01-01

182

Novel pseudo-morphotactic synthesis and characterization of tungsten nitride nanoplates  

International Nuclear Information System (INIS)

A novel pseudo-morphotactic transformation route was developed to synthesize polycrystalline ?-W2N nanoplates by thermally treating tungstate-based inorganic-organic hybrid nanobelts with a lamellar microstructure in an NH3 flow. The tungstate-based hybrid nanobelts were formed in a water-in-oil-microemulsion-like 'commercial H2WO4 powders/n-octylamine/heptane' reaction system. The as-obtained hybrid nanobelts were thermally treated in an NH3 atmosphere at 650-800 oC for 2 h to form cubic ?-W2N nanoplates. XRD, SEM, TEM, FT-IR and TG-DTA were used to characterize the precursors and their final products. The polycrystalline ?-W2N nanoplates derived from hybrid nanobelts, with side lengths of several hundred nanometers, consist of small nanocrystals with an average grain size of 3.2 nm. The formation of ?-W2N nanoplates involved two steps: decomposing tungstate-based hybrid nanobelts into WOy and W species and then ...

2011-02-01

183

Microbiological Comparison of Core and Groundwater Samples Collected from a Fractured Basalt Aquifier with that of Dialysis Chamber Incubated in Situ  

Energy Technology Data Exchange (ETDEWEB)

Microorganisms associated with fractured basalt core were compared to those suspended in groundwater pumped from the same well in the eastern Snake River Plain Aquifer (Idaho, USA). Two wells influenced to different degrees by a mixed-waste plume in the fractured basalt aquifer were examined. In one well, an array of dialysis cells filled with either deionized water or crushed basalt was equilibrated to compare the microorganisms collected in this fashion with those from core and groundwater samples collected in a traditional manner from the same well. Analyses were performed to characterize these samples and to provide a basis for comparison. These included total cell counts by microscopy; total biomass by phospholipid fatty acid analysis; enumerations of viable aerobic heterotrophs, groups of putative aerobic co-metabolic TCE-degraders and aerobic H2-oxidizing bacteria; mineralization of 14C- labeled acetate; and enrichments for dissimilatory ...

2004-04-01

184

Kinetics of mn-based sorbents for hot gas desulfurization: Task 2 - exploratory experimental studies. Quarterly report, March 15, 1996--June 15, 1996  

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to develop a pellet formulation which is capable of achieving low sulfur partial pressures and a high capacity for sulfur, loaded from a hot fuel gas and which is readily regenerable. Furthermore the pellet must be strong for potential use in a fluidized bed and regenerable over many cycles of loading and regeneration. Regeneration should be in air or oxygen-depleted air to produce a high-concentration sulfur dioxide. Fixed-bed tests were conducted with several formulations of manganese sesquioxide and titania, and alumina They were subject to a simplified fuel gas of the oxygen-blown Shell type spiked with a 30,000ppmv concentration of H{sub 2}S. Pellet crush strengths for 4 and 2mm diameter pellets was typically 12 lbs per pellet and 4 lbs per pellet, respectively. For the most favorable of the formulations tested and under the criteria of break-through at less than 100ppmv H2S and loading temperatures of ...

1996-06-12

185

Combined photochemical-biological processes for treatment of unleaded gasoline oxygenates : MTBE, ETBE and TAME  

International Nuclear Information System (INIS)

A study was conducted to determine the feasibility and the opportunity of photochemical pretreatment on the biodegradation and detoxification of Methyl Tert Butyl Ether (MTBE), Ethyl Tert Butyl Ether (ETBE) and Tert Amyl Methyl Ether (TAME), the most common oxygenates used as octane enhancers in unleaded gasoline. The production, storage, uses and disposal of oxygenates result in an unknown amount of groundwater pollution. Because of their high solubility, MTBE, ETBE and TAME are detected in large portions in saturated zones of aquifers. The biodegradation of these oxygenates is difficult and slow, and information regarding their biodegradability is scarce. Photo-decomposition of oxidants under appropriate UV radiation has been shown to be very effective because the hydroxyl radicals produced possess high oxidation potential. In this study, the H_2O_2/UV process was used to generate hydroxyl radicals. Maximal oxygenates ...

1998-10-01

186

Caldicellulosiruptor obsidiansis sp. nov., an anaerobic, extremely thermophilic, cellulolytic bacterium isolated from Obsidian Pool, Yellowstone National Park  

Energy Technology Data Exchange (ETDEWEB)

A novel, obligately anaerobic, extremely thermophilic, cellulolytic bacterium, designated OB47T, was isolated from Obsidian Pool, Yellowstone National Park, WY, USA. The isolate was a non-motile, non-spore forming, Gram-positive rod approximately 2 m long by 0.2 m wide and grew at temperatures between 55-85oC with the optimum at 78oC. The pH range for growth was 6.0-8.0 with values of near 7.0 being optimal. Growth on cellobiose produced the fastest specific growth rates at 0.75 hr-1. The organism also displayed fermentative growth on glucose, maltose, arabinose, fructose, starch, lactose, mannose, sucrose, galactose, xylose, arabinogalactan, Avicel, xylan, filter paper, processed cardboard, pectin, dilute acid-pretreated switchgrass and Populus. OB47T was unable to grow on mannitol, fucose, lignin, Gelrite, acetate, glycerol, ribose, sorbital, carboxymethylcellulose and casein. Yeast extract stimulated growth and thiosulfate, sulfate, nitrate, and sulfur were not reduced. Fermentation ...

2010-02-01

187

The physics of production, acceleration and neutralization of large negative ion beams  

Energy Technology Data Exchange (ETDEWEB)

Neutral beam systems for the next generation of magnetic fusion devices will be based on negative ions. Development are progressing steadily, and large negative ion-based systems are prepared for JT60-U and LHD, and are being considered for ITER. An overview of the physics of the production, acceleration and neutralization of large negative ion beams is given. the present state of the art in Research and Development is also surveyed. (author). 55 refs., 10 figs., 1 tab.

1995-12-31

188

The physics of production, acceleration and neutralization of large negative ion beams  

Energy Technology Data Exchange (ETDEWEB)

Neutral beam systems for the next generation of magnetic fusion devices will be based on negative ions. Developments are progressing steadily, and large negative ion-based systems are under preparation for JT60-U and LHD, and are being considered for ITER. An overview of the physics of the production, acceleration and neutralization of large negative ion beams is given. The present state of the art in R and D is also surveyed. (Author).

1995-11-01

189

Summary and closing remarks  

Energy Technology Data Exchange (ETDEWEB)

A summary of the topics covered in papers presented at the 1995 Brookhaven joint conference on production, neutralization, and application of negative ion beams is given. The conference topics covered included plasma ion sources, plasma seeding of these sources for increased ion production, beam extraction and transport, computer simulation and design studies, and operation of existing and experimental ion source facilities. Application of the sources to accelerator, tokamak, and thin film deposition are discussed. (AIP) {copyright} {ital 1996 American Institute of Physics.}

1996-07-01

190

Self installable: floating production facility requires only light support craft  

Energy Technology Data Exchange (ETDEWEB)

An integrated multiwell floating production, storage, and offloading (FPSO) facility was successfully installed at the Tazerka field offshore Tunisia in 1982. Because there is good reason to believe that the installation techniques developed for the Tazerka FPSO can be applied to even larger systems in deeper waters, this paper presents the design and step-by-step installation procedures developed at Tazerka.

1983-05-01

191

Review of nuclear energy; Ydinenergian tilannekatsaus  

Energy Technology Data Exchange (ETDEWEB)

The report is an overview on the production of the nuclear energy all over the world. The amount of production at present and in future, availability of the nuclear fuel, development of nuclear technology, environmental and safety issues, radioactive waste management and commissioning of the plants and also the competitivity of nuclear energy compared with other energy forms are considered. (91 refs.).

1997-05-01

192

Railways - EA BOOKS  

Wastenet

...91 ex-GST Terms and Conditions For 90 years they were the largest industrial workshops in the State, training tradesmen to build and repair locomotive engineers and rolling stock while maintaining the railway network. Display product Add to shopping basket Dow's Dictionary of Railway Quotations AU$43.59 ex-GST Terms and Conditions An authoritative compendium of quotations about railways from 1608 to the present day. Display product Add to shopping basket Railways and ...

193

Overview of cleaner production as a result of clean technology research in Vietnam  

Energy Technology Data Exchange (ETDEWEB)

Vietnam is beginning its industrialization process, and it currently lacks the capital necessary for expensive pollution control and treatment systems. Pollution strategies are critical for the country. This study evaluates the present status of industry and the pollution problems associated with industrial development in Vietnam. The purpose of the study is to identify sectors that may have potential for promoting cleaner production practices. 4 refs.

1996-12-31

194

Nickel alloy clad steel plate for flue gas desulfurization applications  

Energy Technology Data Exchange (ETDEWEB)

The use of nickel alloys in Flue Gas Desulfurization (FGD) applications is described. Recently, nickel alloys 625 and C-276 have been clad to carbon steel plate. Production and properties of the clad plate are reviewed and a brief discussion is presented on production, fabrication and welding. Laboratory and field corrosion tests in SO/sub 2/ scrubber environments suggest that alloy 625 and C-276 clad steel plates are as corrosion resistant as the solid alloy plate.

1987-01-01

195

Nature of plant stimulators in the production of Acetobacter xylinum ({open_quotes}Tea fungas{close_quotes}) biofilm used in skin therapy  

Energy Technology Data Exchange (ETDEWEB)

Caffeine and related xanthines were identified as potent stimulators for the bacterial cellulose production in A. xylinum. These compounds are present in several plants whose infusions are useful as culture-medium supplements for this acetobacterium. The proposed target for these native purine-like inhibitory substances is the novel diguanyl nucleotide phosphodiesterase(s) that participates in the bacterial cellulogenic complex.

1991-12-31

196

Method of purifying uranium tetrafluoride hydrate and preparing uranium (VI) peroxide hydrate using a fluoride complexing agent  

International Nuclear Information System (INIS)

The annual production of phosphate rock, on the order of about 30-40 million tons yearly, represents several million pounds of uranium. The present invention provides a process of purifying uranium tetrafluoride hydrate to produce a uranium (VI) peroxide product meeting 'yellow cake' standards using a double precipitation procedure. A fluoride complexing agent is used in the precipitation.

1978-06-27

197

Mathematic modeling of the coke gas combustion process  

Energy Technology Data Exchange (ETDEWEB)

Analysis of the coke gas combustion porcess is presented. Standard kinetic relationships were utilized. Calculations were performed for coke gas with high and low content of H/sub 2/ and for blasting air 20 and 100/sup 0/C. Temperature relationships, composition of gas combustion products and release of nitrogen oxides were determined. Results are analyzed which will make it possible to control the composition of combustion products.

1983-01-01

198

Mass charge and angular momentum transfer in "1"0"6Cd + 255 MeV "5"4Fe collision studied by #gamma#-#gamma# coincidences  

International Nuclear Information System (INIS)

The distribution of mass, charge and angular momentum transfer among the products of 54-Fe (255 MeV) ions collisions with the 106 Cd target have been studied. The energy level schemes for 92-Mo, 60-Ni, 96-Ru and 56-Fe are presented. The production yields of different isotopes were also measured. 1 ref., 14 figs.

1991-12-01

199

Lignocellulosic feedstock resource assessment  

Energy Technology Data Exchange (ETDEWEB)

This report provides overall state and national information on the quantity, availability, and costs of current and potential feedstocks for ethanol production in the United States. It characterizes end uses and physical characteristics of feedstocks, and presents relevant information that affects the economic and technical feasibility of ethanol production from these feedstocks. The data can help researchers focus ethanol conversion research efforts on feedstocks that are compatible with the resource base.

1998-09-01

200

Joined ceramic product  

Energy Technology Data Exchange (ETDEWEB)

According to the present invention, a joined product is at least two ceramic parts, specifically bi-element carbide parts with a bond joint therebetween, wherein the bond joint has a metal silicon phase. The bi-element carbide refers to compounds of MC, M.sub.2 C, M.sub.4 C and combinations thereof, where M is a first element and C is carbon. The metal silicon phase may be a metal silicon carbide ternary phase, or a metal silicide.

2001-01-01

201

Gamma scanning of FBTR fuel pins  

International Nuclear Information System (INIS)

This paper presents the results obtained in the gamma scanning of two fuel pins from the bent subassembly of the fast breeder test reactor (FBTR) using a segmented gamma scanning system employing segment correlation developed for the assay of glove box solid waste. In addition to the actinide profiles, the paper also discusses the fission products and clad activation product profiles and tries to correlate the experimental values of the latter with computed values. (author). 4 refs., 1 fig., 1 tab.

202

Di-boson production at the Tevatron  

Energy Technology Data Exchange (ETDEWEB)

The authors present some precision measurements on electroweak physics performed at the Tevatron collider at Fermilab. Namely they report on the boson-pair production cross sections and on triple gauge boson couplings using proton anti-proton collisions collected by the CDF and D0 experiments at the center-of-mass energy of 1.96 TeV. The data correspond to an integrated luminosity of up to 324 pb{sup -1}.

2005-05-01

203

Use of gadolinium as neutron poison in 540 MWe PHWR  

International Nuclear Information System (INIS)

In Pressurised heavy water reactors (PHWRs), neutron poison in the moderator is used to compensate the excess reactivity present in the core on different occasions such as xenon decay during synchronization just after poison out period or start ups from xenon free conditions. It is also used in secondary shutdown system (SDS-2), where required amount of neutron poison is injected directly into the moderator within 2.5 seconds. Further, it is also used for over poisoning the moderator to achieve the guaranteed shutdown state when the regular shutdown systems are taken for maintenance. Generally, two types of moderator poisons are used in power reactors to balance the reactivity of the core and they are boron and gadolinium. Gadolinium is used in the form of gadolinium nitrate (Gd(NO3)3.6H2O). The paper gives the details of estimation of reactivity coefficients of gadolinium for 540 MWe PHWR for different operating ...

2006-11-13

204

Genome analysis of F. nucleatum sub spp vincentii and its comparison with the genome of F. nucleatum ATCC 25586.  

Science.gov (United States)

We present the draft genome sequence and its analysis for Fusobacterium nucleatum sub spp. vincentii (FNV), and compare that genome with F. nucleatum ATCC 25586 (FN). A total of 441 FNV open reading frames (ORFs) with no orthologs in FN have been identified. Of these, 118 ORFs have no known function and are unique to FNV, whereas 323 ORFs have functional orthologs in other organisms. In addition to the excretion of butyrate, H2S and ammonia-like FN, FNV has the additional capability to excrete lactate and aminobutyrate. Unlike FN, FNV is likely to incorporate galactopyranose, galacturonate, and sialic acid into its O-antigen. It appears to transport ferrous iron by an anaerobic ferrous transporter. Genes for eukaryotic type serine/threonine kinase and phosphatase, transpeptidase E-transglycosylase Pbp1A are found in FNV but not in FN. Unique ABC transporters, cryptic phages, and three types of restriction-modification ...

2003-06-01

205

Thermodynamic study of systems with lower critical solution temperatures: H_2O + (C_2H_5)_3N, D_2O + (C_2H_5)_3N  

International Nuclear Information System (INIS)

Molar excess enthalpies and molar excess volumes are reported for the systems H_2O + (C_2H_5)_3N and D_2O + (C_2H_5)_3N at temperatures below and above their lower critical solution temperatures. The molar excess enthalpies are slightly less exothermic for the D_2O system. The molar excess volumes of the H_2O and D_2O systems are within experimental error of one another. Compositions of conjugate solutions estimated from the calorimetric and volumetric measurements agree with those obtained from published liquid-liquid phase diagrams. (Auth.).

1979-01-01

206

Synthesis and Crystal Structures of Octahedral Metal Complexes containing the New Dianion [PhP(Se,O)Se-Se(O,Se)PPh]2-  

British Library Electronic Table of Contents (United Kingdom)

The synthesis and structures of three new compounds are reported. [Mg2{PhP(Se,O)Se-Se(O,Se)PPh}2(thf)7(H2O)3] (1), [Mg{PhP(Se,O)Se-Se(O,Se)PPh}(thf)3(H2O)] (2), and [Mn{PhP(Se,O)Se-Se(O,Se)PPh}(thf)3(H2O)] (3) were prepared by treatment of Woollins reagent [PhP(Se)(m-Se)]2 with the corresponding hydrated metal acetates.

2007-01-01

207

Preconceptual study of an advanced MAPLE research reactor  

International Nuclear Information System (INIS)

The Advanced MAPLE is a research reactor design under development as a high-flux neutron source. The main performance goals for the reactor are a high peak thermal neutron flux in a heavy-water reflector tank, and a high average fast neutron flux in a central irradiation facility, with a maximum linear fuel rod rating of less than 120 kW/m. This study investigated the neutronic and reactor design consequences of the use of H_2O coolant as opposed to D_2O. The neutronics results, and several other considerations, indicate that H_2O coolant has a number of advantages. It is suggested that the H_2O coolant option be considered in the design of the Advanced MAPLE reactor. (L.L.) 9 refs., 4 figs., tab.

1990-06-03

208

Interaction of iodine-containing acids with o-methylacetanilide in aqueous solutions  

International Nuclear Information System (INIS)

The systems CH_3COHNC_6H_4CH_3-HI-H_2O, CH_3CONHC_6H_4CH_3-HIO_3-H_2O, CH_3CONHC_6H_4CH_3-H_5IO_6-H_2O have been studied by the solubility method. It has been ascertained that the systems containing periodic and iodic acids are referred to systems of simple eutonic type. Formation of compound of o-methylacetanilide with iodic acid of equimolecular composition has been proved. Concentrational boundaries of its existence in solutions have been established, its certain physicochemical characteristics being determined.

209

Graphene-Pt nanocomposite for nonenzymatic detection of hydrogen peroxide with enhanced sensitivity  

British Library Electronic Table of Contents (United Kingdom)

A sensitive hydrogen peroxide (H2O2) sensor was fabricated based on graphene-Pt (GN-Pt) nanocomposite. The GN-Pt was synthesized by photochemical reduction of K2PtCl4 on GNs, and characterized by atomic force microscope (AFM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). Electrochemical investigations indicated that the GN-Pt exhibited a high peak current and low overpotential towards the reduction of H2O2. The GN-Pt modified glass carbon electrode displayed a wide linear range (2-710mM), low limit of detection (0.5mM) and good selectivity for detection of H2O2 with a much higher sensitivity than that of Pt nanoparticles or graphene modified electrode.

2011-01-01

210

Conversion of ortho-para H2O isomers in water and a jump in erythrocyte fluidity through a microcapillary at a temperature of 36.6?0.3?C  

British Library Electronic Table of Contents (United Kingdom)

A mechanism is proposed for the previously observed [1] jump in erythrocyte fluidity through a microcapillary 1.3 ?m in diameter at a temperature of 36.6?0.3?C. Our interpretation is based on the experimental evidence both for existence of ortho and para H2O isomers in water and on spin-selective interaction of proteins with para H2O isomers as hydration shells of biomolecules are being formed [2]. It is important that the formation of hydration shells of proteins and DNA in aqueous solutions is accompanied by an increase in the Brillouin shift to 0.4 cm?1 (?0.25 cm?1 in water), which points to the formation of icelike structures. We believe that the coincidence of the translational energy kT of the Brownian motion and the energy of the rotational quanta for the 313?202 transition of para ...

2009-01-01

211

Project scheduling with resources constraints: application in the equipment production for the oil industry; Scheduling de projetos com restricao de recursos: aplicacao na producao de equipamentos para a industria de petroleo  

Energy Technology Data Exchange (ETDEWEB)

One of the essential steps in the main scope Project Management is the Time Management made by the planning and control of the project schedule. In this work is presented the resource constrained scheduling problem beyond its mathematical formulation and a review of papers about this issue. In sequence is presented a practical example of this model considering a simplified model of an engineering project schedule of oil production equipment. The results obtained with the model application are shown and the conclusions about the work with resource constrained scheduling problems. (author)

2008-07-01

212

Problematic of atmospheric pollution in Lebanon: the better stake is apprehended, the best acts are taken  

International Nuclear Information System (INIS)

The article is an overview on atmospheric pollution in Lebanon. It presents an analysis of sources of pollution in the country and their impacts on local and global environment and describes their control. Air pollution is mainly due to the industrial, electrical and transportation sectors. Pollutants from fuel combustion are analyzed. It is estimated that in 2010, CO_2 emissions will reach 5987250 tons, SO_2 emissions is estimated to be 182950 tons, Nox to 105180 and dusts to 4965 tons. CFC consumption and measures of control according to Montreal protocol are described. Consumption of primary energy, consumption of petroleum products, quantity of petroleum in refineries and production of cement in Lebanon are also presented in tables

2000-02-01

213

Application properties of AB{sub 2}-type hydrogen absorbing alloys  

Energy Technology Data Exchange (ETDEWEB)

Use of hydrogen absorbing alloys in various practical applications is always connected with the problem of production of starting alloys. The transition from laboratory samples to small-scale production involves the change of furnace and its operation mode and this has an effect on the preparation method of mixture of starting metal. Also, for some applications such as thermosorption compressors the exact values of thermodynamical parameters of reaction are needed. In the present work we present the results of investigation of series Laves phase hydrogen-absorbing alloys which can be promising in for use in different devices. 1 ref.

1998-07-01

214

Chemical modification of soybean oil for lubricant  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a series of structural modifications of soybean oils for lubricant. The reaction was monitored and products were confirmed by NMR and FTIR. The structural modification is carried out in four stages, (1) synthesis of soybean oil isooctyl ester from soybean oil; (2) synthesis of epoxy-soybean oil isooctyl ester from soybean oil isooctyl ester; (3) synthesis of hydroxylated products from epoxy soybean oil isooctyl ester with fatty acid; (4) esterification of the hydroxylated product with anhydride. Rheological behaviour of the products was measured. Pour points of the products (3) were observed as low as -24 C (lauric acid) and -15 C (isooctanoic acid) respectively. When the hydroxyl groups in the products were esterified with and acid anhydride, the pour points were became higher, which were -21 C (lauric acid) and -6 C ...

2008-07-01

215

Consumer attitudes and decision-making with regard to genetically engineered food products: A review of the literature and a presentation of models for future research  

DEFF Research Database (Denmark)

Executive summary 1. Few studies have to date explained consumer attitudes and purchase decisions with regard to genetically engineered food products. However, the increased marketing of genetically engineered food products and the considerable concern that consumers seem to express with regard to the technology call for the development of a theoretical basis for research into these issues. 2. The aim of the paper is to present three models which we have developed to explain consumer attitudes, buying behaviour and attitude change with regard to genetically engineered food products. All three models build on established consumer behaviour theory and on existing and comparable research in the field. 3. Consumer attitudes toward genetic engineering in food products are explained in an attitude model that builds on Fishbein's multiattribute attitude model. The model deviates from ...

1998-01-01

216

Wilsonville Advanced Coal Liquefaction Research and Development Facility, Wilsonville, Alabama. Technical progress report, Run 243 with Illinois 6 coal  

Science.gov (United States)

This report presents the operating results for Run 243 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary objective was to demonstrate the effect of a dissolver on the ITSL product slate, especially on the net C/sub 1/-C/sub 5/ gas production and hydrogen consumption. Run 243 began on 3 February 1983 and continued through 28 June 1983. During this period, 349.8 tons of coal was fed in 2947 hours of operation. Thirteen special product workup material balances were defined, and the results are presented herein. 29 figures, 19 tables.

1984-02-01

217

Total M shell X-ray production cross sections and average fluorescence yields in 11 elements from Tm to U at photon energy of 5.96 keV  

International Nuclear Information System (INIS)

Total M shell X-ray production cross section for 11 elements with 69 #<=# Z #<=# 92 have been measured using an incident photon energy of 5.96 keV. Measurements have been performed using an "5"5Fe annular source and a Si(Li) detector. Average M shell fluorescence yield at each incident photon energy has been deduced, using the experimental total M X-ray production cross section and theoretical M shell photoionization cross section. Present experimental results are compared with other experimental and theoretical values. Reasonable agreement (to within 0.3-28%) is typically obtained between present and other experimental and theoretical values.

2005-04-01

218

Nuclear fragmentation of clinical silicon beam  

Energy Technology Data Exchange (ETDEWEB)

Heavy ions used for biomedical studies fragment when they pass through matter. It is known that different fragments cause different types of biological damage. In this paper, results pertaining to differrent kinds of secondary fragments produced by a /sup 28/Si beam at 463 MeV/nucleon in its interaction with nuclear emulsion are presented. It is observed that the production frequencies of secondary fragments are independent of the target. Partial production cross sections and fluences of the secondary fragments are also discussed. The partial production cross sections for different fragments at three lower energy ranges are practically the same within their statistical errors except for the cross section for Li fragments, which is larger by almost a factor of 1.5 at the lowest energy investigated. The dose contributions of the primary Si beam and its components at different points of the Bragg curve are ...

1985-02-01

219

Embodied energy and emergy evaluation of a typical biodiesel production chain in China  

British Library Electronic Table of Contents (United Kingdom)

Biodiesel from non-grain feedstock has been considered as one of the proper substitutes for fossil fuels associated with a series of activities emerging in China in order to meet the resource shortage and develop the energy crops. This paper presents an ecological accounting framework based on embodied energy, emergy, and CO2 emission for the whole production chain of biodiesel made from Jatropha curcas L. (JCL) oil. The energy and materials invested in and CO2 emission from the whole process, including cropping, transportation, extraction, and production, are accounted and calculated. Also, EmCO2, the ratio of real CO2 released to the emergy-based sustainability indicator per joule biodiesel, is proposed in this paper to present a new goal function for low-carbon system optimization. Fina...

2011-01-01

220

Development of plasticity processing of magnesium alloys  

Energy Technology Data Exchange (ETDEWEB)

Recent developments on plastic forming technology of magnesium alloys are presented. Attempts have been undergoing with an aim at forming magnesium alloy parts at lower temperatures. It is believed that fine microstructure magnesium alloys usually have much higher plasticity at lower temperatures and even room temperatures. Extrusion is a method to form magnesium profile products and tube products, which is also one of the effective ways to make fine microstructure magnesium alloys. Superplasticity forming is another method to form high plasticity magnesium alloys. Hot forming of magnesium sheet parts is an important process to form magnesium products. Some developments related to above issues are discussed in the present paper. (orig.)

2003-07-01

221

Techno-economic comparison of a biological hydrogen process and a 2nd generation ethanol process using barley straw as feedstock  

British Library Electronic Table of Contents (United Kingdom)

A process combining dark fermentation and photofermentation for production of hydrogen is interesting due to its potential of producing hydrogen at a high yields. In this study, the hydrogen process is compared to a 2nd generation ethanol process with respect to cost and with the aim of increasing our understanding of the pros and cons and giving a clear picture of the present status of the two processes. The hydrogen production cost was found to be about 20 times higher than the ethanol production cost, 421.7&z.euro;/GJ compared to 19.5&z.euro;/GJ. The main drawbacks of the hydrogen process are its low productivity, low energy efficiency, and the high cost of buffer and base required to control the pH.

2011-01-01

222

Superheavy elements with the Berkeley gas-filled separator  

Energy Technology Data Exchange (ETDEWEB)

In April and May of 1999 the Berkeley Gas-filled Separator was used to search for the production and decay of element 118 from the {sup 86}Kr + {sup 208}Pb reaction, according to Smolanczuk's predictions of relatively large production rates. Three decay chains, each consisting of an implanted heavy ion, followed by a rapid (ms) succession of high-energy (>10 MeV) alpha-particle decays were detected. These chains are consistent with the production and decay of element 118 with mass number 293. These results a) show experimental evidence for the existence of shell-stabilized superheavy elements, b) provide experimental values for refinement of nuclear mass models in the superheavy element region, and, most importantly, c) present a new' reaction pathway for the production of superheavy elements. (author)

2000-03-01

223

Quality assurance requirements for high-level waste form production  

International Nuclear Information System (INIS)

The Department of Energy has issued a Quality Assurance (QA) specification for organizations involved in making a canistered high-level waste form product that is acceptable for storage in a deep geologic federal repository. The logic for the waste form acceptance process is described. In addition to NQA-1 requirements, fourteen supplemental QA requirements have been drafted to fit the waste form production process. A review plan for assuring complicance with the QA specification is provided. Guidelines for preparation of a waste form producer QA program are also presented. It is expected that the QA program description that result will be influential in supporting the acceptybility of the product to OCRWM and for ultimate disposal of the high-level waste in a deep geologic repository. (author) 3 figs., 4 refs.

224

QCD corrections to bb/cc pair production in polarized {gamma}{gamma} collisions and the intermediate mass Higgs signal  

Energy Technology Data Exchange (ETDEWEB)

We present production rates of the two- and three-jet final states for the processes of massive cc/bb quark production in circularly polarized photon-photon collisions, including QCD radiative corrections. Lowest-order cross section, one-loop virtual correction, and gluon emission correction are shown to be of the same order of magnitude for bb quark production at s{sub {gamma}{gamma}} similar 100 GeV. It is shown that the signal from an intermediate mass Higgs boson is observable at a photon-photon collider, though the statistical significance is substantially reduced with respect to the tree-level calculation. ((orig.)).

1995-02-01

225

QCD corrections to bb/cc pair production in polarized #gamma##gamma# collisions and the intermediate mass Higgs signal  

International Nuclear Information System (INIS)

We present production rates of the two- and three-jet final states for the processes of massive cc/bb quark production in circularly polarized photon-photon collisions, including QCD radiative corrections. Lowest-order cross section, one-loop virtual correction, and gluon emission correction are shown to be of the same order of magnitude for bb quark production at s_#gamma#_#gamma# similar 100 GeV. It is shown that the signal from an intermediate mass Higgs boson is observable at a photon-photon collider, though the statistical significance is substantially reduced with respect to the tree-level calculation. ((orig.)).

226

Monte Carlo optimization technique applied to "2"3"8Pu production in FFTF [Fast Flux Test Facility  

International Nuclear Information System (INIS)

An accurate neutronics calculation of a local thermal environment within a fast reactor presents a major challenge. A method was previously described that used Monte Carlo techniques within a macrocell to make accurate and reasonably efficient design calculations for such an environment. This method is now being further optimized for the calculation of "2"3"8Pu production in the Fast Flux Test Facility (FFTF). Here, it is not only important to determine the "2"3"8Pu production from neutron capture in "2"3"7Np, but also to calculate the production of the contamination isotope "2"3"6Pu from high-energy (n,2n) and (#gamma#,n) reactions. The power of the Monte Carlo method to automatically include geometry and energy self-shielding is retained by optimization using fission neutron source biasing in both space and energy.

1989-11-26

227

Evolutionary developments advancing the floating production, storage, and offloading concept  

Energy Technology Data Exchange (ETDEWEB)

Tanker-based floating production, storage and offloading (FPSO) systems have been in operation since Aug. 1977, when a single-well FPSO was put into production by Shell Espana in the Mediterranean. The overall operational experience with this system at this field is reviewed. Special attention is directed to the wireline workover facilities which have proven to be satisfactory. A subsequent evolutionary step, a FPSO accommodating multiple wells, necessitated development of a multiple-bore product swivel. A design program for this swivel was initiated in 1978, a prototype was built and fullscale testing finalized in 1980. A summary of the test results is presented. Simultaneous with the multiple-bore swivel development, detailed engineering for an 8-well FPSO was begun. This sytem includes gas lift a

1982-01-01

228

Abstracts of 5. International conference 'Nuclear and Radiation Physics'  

International Nuclear Information System (INIS)

The 5-th International conference 'Nuclear and Radiation Physics' was held in Almaty (Kazakhstan) 26-29 September 2005. Besides basic problems of nuclear and solid state physics the conference paid considerable attention to applied topics important for industry and science in Kazakhstan; they include fuel and construction materials for nuclear power production, new technologies and materials for their production, materials for hydrogen power production, handling and utilization of radioactive waste, analytical methods for combating with illicit trafficking of nuclear and radioactive materials, technologies for reduction and assessment of environmental risk from radiation-hazardous materials and sites, production and application of isotopes, application of nuclear technologies in medicine and industry. On the conference more than 300 papers were presented by participants from 20 ...

2005-09-26

229

hysics Facility - NASA  

Science.gov (United States)

vehicles including the H2-A rocket and the space shuttle. .... The vacuum can's main function is to provide a high vacuum so that the science experiment and its sensors ... EMI-shielded power conversion from the incoming ISS power supply. 4. ...

230

The optical and structural properties of polycrystalline Cu(In,Ga)(Se,S)2 absorber thin films  

British Library Electronic Table of Contents (United Kingdom)

The pentenary compound semiconductor Cu(In,Ga)(Se,S)2 is one of the most attractive materials for high-efficiency solar cells due to its tunable band gap to match well the solar spectrum. In this study, semiconducting Cu(In,Ga)(Se,S)2 thin films were prepared by a classical two-step growth process, which involves the selenization and/or sulfurization of In/Cu?Ga precursor. During the precursor formation step metallic In/Cu?Ga alloys were deposited onto the Mo-coated soda-lime glass substrates by DC magnetron sputter process. The respective precursors were subsequently reacted with H2Se and/or H2S gasses, at elevated temperatures. By optimizing the selenization parameters, such as the gas concentrations, reaction time, reaction temperature, and the flow of H2Se and H2S, high quality, single...

2011-01-01

231

The Effect of O2, H2O, and N2 on the Fatigue Crack Growth Behavior of an Alpha + Beta Titanium Alloy at 24 C and 177 C  

Science.gov (United States)

To study the effects of atmospheric species on the fatigue crack growth behavior of an a+B titanium

2001-01-01

232

Solar photochemistry and heterogeneous photocatalysis  

International Nuclear Information System (INIS)

The search for alternative energy supplies continues since the oil crisis of 1973. One energy vector is dihydrogen, H_2. Of the group VI hydrides, water has been the focus of most studies in harnessing solar energy and generating H_2. Two basic photochemical strategies have been employed: molecular photocatalytic systems, and semiconductor based photocatalytic systems. The results have not met with the euphoric expectations of the mid-1970's because of the difficulties encountered in H_2O splitting (E"0 S"2 "-/S = + 0.51 eV, NHE) is another vehicle tapped as a potential source of H_2. Heterogeneous photocatalysis utilizing semiconductor particulates and sunlight as the photon source has been successful with interesting quantum efficiencies. To this end, novel photocatalytic devices have been developed; one of these uses ...

233

Probing active galactic nuclei with H2O megamasers.  

UK PubMed Central (United Kingdom)

We describe the characteristics of the rapidly rotating molecular disk in the nucleus of the mildly active galaxy NGC4258. The morphology and kinematics of the disk are delineated by the point-like...Full Text Available

1995-12-05

234

Plasma nitriding of austenitic stainless steel in N_2 and N_2/H_2 gas admixture  

International Nuclear Information System (INIS)

Plasma nitriding in glow discharge is a process of modifying surface properties of a material by which surface hardness, corrosion resistance, fatigue strength etc. of a material can be improved

2004-09-01

235

Onset of Quiescence Following p53 Mediated Down-Regulation of H2AX in Normal Cells  

UK PubMed Central (United Kingdom)

Normal cells, both in vivo and in vitro, become quiescent after serial cell proliferation. During this process, cells can develop immortality with genomic instability,...Full Text Available

236

Magnetic moment measurements of gadolinium, holmium and ytterbium tartrate trihydrate crystals  

British Library Electronic Table of Contents (United Kingdom)

Magnetic moment and susceptibility of single crystals of rare earth tartrates of the type R(C4H4O6)(C4H5O6)3H2O (where R = Gd, Ho, and Yb), using a vibration sample magnetometer are reported. The experimental values of molar susceptibilities for Gd(C4H4O6)(C4H5O6)3H2O, Ho(C4H4O6)(C4H5O6)3H2O, and Yb(C4H4O6)(C4H5O6)3H2O are 2.58x10-2, 4.66x10-2, and 8.03x10-3 (in cgs em units), respectively. The calculated effective magnetic moments are in good agreement with the theoretical predictions on rare earth ions.

2008-01-01

237

Human placental transport of cimetidine.  

UK PubMed Central (United Kingdom)

This study addresses the mechanism of transport of the H2-receptor antagonist, cimetidine, by the human placenta. A 4-h recycling perfusion of a single placental cotyledon of normal, term, human placenta...Full Text Available

1987-11-01

238

H_2 emission arises outside photodissociation regions in ultra-luminous infrared galaxies  

CERN Document Server

Ultra-luminous infrared galaxies are among the most luminous objects in the local universe and are thought to be powered by intense star formation. It has been shown that in these objects the rotational spectral lines of molecular hydrogen observed at mid-infrared wavelengths are not affected by dust obscuration, leaving unresolved the source of excitation of this emission. Here I report an analysis of archival Spitzer Space Telescope data on ultra-luminous infrared galaxies and demonstrate that star formation regions are buried inside optically thick clouds of gas and dust, so that dust obscuration affects star-formation indicators but not molecular hydrogen. I thereby establish that the emission of H_2 is not co-spatial with the buried starburst activity and originates outside the obscured regions. This is rather surprising in light of the standard view that H_2 emission is directly associated with ...

2010-01-01

239

Control of adsorption by microwave irradiation; Maikuroha nado wo mochiita gas no kyuchaku datsuri seigyo  

Energy Technology Data Exchange (ETDEWEB)

Introduced herein is microwave irradiation for the adsorption and desorption of environmental pollutants. Microwaves may be used in two ways, other than through elevation of temperature of a system as a whole with the adsorbent such as activated carbon serving as the heating medium. The first is the application by which desorption is caused to take place of specified molecules. For example, zeolite that has adsorbed water is regenerated when it is irradiated with microwaves in a stream of cooling gas. This is because only the moisture is heated since zeolite is a non-carbon adsorbent that absorbs microwaves but a little. Another case is reported in which microwaves are utilized to desorb H2S, H2O, CO, etc., from molecular sieves. In the second application, coexisting materials different in absorptivity are exposed to irradiation. The adsorption of microwave-absorbent materials is inhibited while that of ...

1997-01-25

240

+ 2004 - The NASA Glenn Research Center Technical Report Server  

Science.gov (United States)

May 31, 2011 ... Synthesis and Structural Characterization of a Novel Indium Mercapto Derivative [Clln(SCH2(CO)O)2]2-[(4-MepyH)2]2+. 284. System Mass ...

241

Feasibility study on production of Co-60 in PHWR  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ...

2000-05-01

242

Synthesis and Structural Characterization of a Novel Indium Mercapto Derivative (Clln(SCH2(CO) O)2)2-((4-MepyH)2)2+.  

Science.gov (United States)

The synthesis and structural characterization of a novel In(III) complex is described. The reaction between InCl3 with sodium mercapto-acetic acid, (NaSCH2(CO)OH) in 4-methylpyridine, (CH3(C5H5N), (4-Mepy)) at 25 C affords (ClIn(SCH2(CO)O)2)2- ((4-MepyH)2...

2004-01-01

243

Structures and luminescent properties of new uranyl-based hybrid materials  

International Nuclear Information System (INIS)

Six uranyl coordination compounds, UO_2(OH)(PYCA) (1), UO_2(PYCA)_2(H_2O).2H_2O (2), UO_2(PIC)_2 (3), UO_2(H_2O)_2(NIC)_2 (4), UO_2(OH)(HINIC)(INIC) (5), and UO_2(PYTAC)_2(H_2O)_2 (6) were grown as single crystals via hydrothermal synthesis (PYCA - pyrazine-2-carboxylate, PIC - picolinate, NIC - nicotinate, INIC - iso-nicotinate, and PYTAC - 2-(pyridin-4-yl)thiazole-5-carboxylate) to study their optical properties. All six compounds have been identified via single crystal X-ray diffraction and fully characterized via powder X-ray diffraction, infrared spectroscopy, UV-Vis spectroscopy, and fluorescence spectroscopy. Three of the complexes, 1, 3, and 6, represent new structures, and their synthesis and structural characterization is detailed within. The structures of 2, 4, and 5 have previously been reported in the ...

2011-06-01

244

Polythermal study of the M(ClO_4)_2-H_2O systems, where M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+  

International Nuclear Information System (INIS)

Crystallization points of aqueous solution of the systems M(ClO_4)_2-H_2O (M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+), depending on the salt concentration, were identified by visual-polythermal method. Relying on model notions on the structure of the electrolyte solutions, specific features of strontium perchlorate solubility polytherm and concentration dependence of the relative dynamic viscosity of the salt aqueous solutions are discussed

2005-03-01

245

iWork '09 The Missing Manual  

CERN Document Server

With iWork '09: The Missing Manual, you'll quickly learn everything you need to know about Apple's incredible productivity programs, including the Pages word-processor, the Numbers spreadsheet, and the Keynote presentation program that Al Gore and Steve Jobs made famous. This book gives you crystal-clear and jargon-free explanations of iWork's capabilities, advantages, and limitations to help you produce stunning documents and cinema-quality digital presentations in no time.

2009-01-01

246

Searches for standard model Higgs at the Tevatron  

Energy Technology Data Exchange (ETDEWEB)

A summary of the latest results of Standard Model Higgs boson searches from CDF and D0 presented at the DIS 2007 conference is reported in this paper. All analyses presented use 1 fb{sup -1} of Tevatron data. The strategy of the different analyses is determined by the Higgs production mechanism and decay channel.

2007-04-01

247

Searches for Standard Model Higgs at the Tevatron  

Energy Technology Data Exchange (ETDEWEB)

A summary of the latest results of Standard Model Higgs boson searches from CDF and D0 presented at the DIS 2007 conference is reported in this paper. All analyses presented use 1 fb{sup -1} of Tevatron data. The strategy of the different analyses is determined by the Higgs production mechanism and decay channel.

2007-11-01

248

Practical design methods for barrier pillars. Information circular/1995  

Energy Technology Data Exchange (ETDEWEB)

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

1995-11-01

249

Correlations between D and Dbar mesons in high energy photoproduction  

Energy Technology Data Exchange (ETDEWEB)

Over 7000 events containing a fully reconstructed D{bar D} pair have been extracted from data recorded by the FOCUS photoproduction experiment at Fermilab. Preliminary results from a study of correlations between D and {bar D} mesons are presented. Correlations are used to study perturbative QCD predictions and investigate non-perturbative effects. We also present a preliminary result on the production of {psi}(3770).

2002-11-13

250

Campylobacter jejuni, C. coli, and C. lari naturally present in Leghorn laying hens and the antibiotic resistance profiles of these organisms  

Science.gov (United States)

Campylobacter spp. are present in the intestinal tract and internal tissues of broiler breeder and broiler chickens. Campylobacter spp. are known to cause acute bacterial gastroenteritis in humans and raw poultry products have been implicated as a significant source of these infections. The object...

251

Reducing indoor air formaldehyde concentrations  

Energy Technology Data Exchange (ETDEWEB)

Urea-formaldehyde resin bonded particle board, medium density fiberboard and plywood paneling are used as flooring, wall paneling, for cabinet work and in furniture, and are present in almost every office, home and public building. If large quantities of these products are used in poorly ventilated spaces, high manufacturing quality control is necessary to avoid problems of latent formaldehyde release. Indoor air formaldehyde concentrations depend on the nature of the product, the product surface to air volume (loading) factor, temperature, humidity, age and product emission rates. Standard test methods are now available for measuring product emission rates that make it possible to predict the performance of UF-bonded pressed wood materials if use conditions and environmental parameters are known. Recent modifications in adhesive and board manufacturing ...

1985-08-01

252

Potential for energy production and use from biogas in Brazil; Potencial de aproveitamento energetico do biogas no Brasil  

Energy Technology Data Exchange (ETDEWEB)

Biogas, produced from anaerobic digestion of organic matter in domestic, industrial and rural wastewaters and residuals, represent an alternative and renewable source of energy, with growing use worldwide. In Brazil, high population and its spatial concentration and expressive agricultural and agricultural-industrial production indicate a substantial potential of biogas production. The results presented in this work show a potential of biogas production of almost 2 billion cubic feet a day of CH{sub 4}. Viability of biogas production and use depends substantially on project scale. Generally, biogas projects are viable from landfills and domestic wastewater treatment for populations higher than 50,000 inhabitants and swine and dairy farms with at least 5,000 and 1,000 animals, respectively. Biogas is also competitive when compared to fossil fuels used in industry and transport. ...

2009-12-15

253

Increasing the operational safety of nuclear facilities by using special insulation parts in the containment zone  

International Nuclear Information System (INIS)

LOCA (Loss of coolant accident) resistant heat-shrinkable polymeric products are widely used for the connection of LV cables for class 1E systems inside the containment area of nuclear power plants. The paper/presentation describes the verification of a reformulated compound for these products, where certain components of the compound formulation had to be substituted. A qualification programme with this so-called reformulated compound was undertaken to proof the equivalency of the products to the products made out of the original compound. The basic elements of this requalification project were material qualification tests including accelerated aging tests according to the arrhenius method and type tests in accordance to IEEE 383, including flammability tests. The test results showed that the products made out of the reformulated compound were similar in fit, ...

2005-06-15

254

Microscopic properties of passive films on Ti and Zr from optical, electrochemical and SXM-measurements  

International Nuclear Information System (INIS)

A combined application of several microtechniques is presented and discussed with the Ti/TiO_2 and Zr/ZrO_2-systems as an example. All measurements were carried out on single grains of technical materials in order to detect and quantify the effect of substrate microstructure on the properties of anodic passive films formed potentiodynamically in 0.5 M H_2SO_4 (dU/dt = 20 mVs"-"1). Anisotropy-micro-ellipsometry (AME) was employed to determine the crystallographic orientation of the substrate grains along with passive film thickness and crystallinity in dependence on the anodization potential. Both the isotropic (amorphous) TiO_2- and the anisotropic (crystalline) ZrO_2-films exhibit a systematic dependence of film thickness on the grain orientation. Local LASER-scanning photocurrent measurements (#lambda#=257 nm) on the same grains likewise show a heterogeneity of the photoelectrochemical reactivity in all cases. This is ...

1998-03-01

255

Investigation of the dc vacuum breakdown mechanism  

Science.gov (United States)

Breakdowns occurring in rf accelerating structures will limit the ultimate performance of future linear colliders such as the Compact Linear Collider (CLIC). Because of the similarity of many aspects of dc and rf breakdown, a dc breakdown study is underway at CERN to better understand the vacuum breakdown mechanism in a simple setup. Measurements of the field enhancement factor ? show that the local breakdown field is constant and depends only on the electrode material. With copper electrodes, the local breakdown field is around 10.8GV/m, independent of the gap distance. The ? value characterizes the electrode surface state, and the next macroscopic breakdown field can be well predicted. In breakdown rate experiments, where a constant field is applied to the electrodes, clusters of consecutive breakdowns alternate with quiet periods. The occurrence and lengths of these clusters and quiet periods depend on the evolution of ?. The application of a high field can even modify the electrode ...

2009-09-01

256

High-precision Penning-Trap measurements of light-ion masses  

International Nuclear Information System (INIS)

The UW-Penning Trap Mass Spectrometer (PTMs) is ideally suited for high precision measurements of atomic masses throughout the periodic table upon using highly-stripped ions. However, at the present time, this device has been applied extensively to the light elements ("1H, "2H, "3H, "3He, "4He, "1"2C, "1"3C, "1"4N, "1"6O) due to their fundamental importance. Atomic masses follow immediately from a comparison with some multiply-charged carbon ion, after correcting for the lost electrons and their corresponding binding energies. For instance, the most recent C"5"+/C"6"+ comparison yielded a discrepancy of -0.30(33) ppb, limited only by the magnetic field instability for a 40-h run. The initial emphasis on hydrogen has now produced a 1-ppb value for the proton's atomic mass and similar work with deuterium has yielded a 2.5-ppb value for the neutron's atomic mass. However, the most significant result is the "3H-"3He mass ...

1993-04-12

257

A QUINTET OF BLACK HOLE MASS DETERMINATIONS  

International Nuclear Information System (INIS)

We report five new measurements of central black hole masses based on Space Telescope Imaging Spectrograph and Wide Field Planetary Camera 2 observations with the Hubble Space Telescope (HST) and on axisymmetric, three-integral, Schwarzschild orbit-library kinematic models. We selected a sample of galaxies within a narrow range in velocity dispersion that cover a range of galaxy parameters (including Hubble type and core/power-law surface density profile) where we expected to be able to resolve the galaxy's sphere of influence based on the predicted value of the black hole mass from the M-#sigma# relation. We find masses for the following galaxies: NGC 3585, M _B_H = 3.4"+"1"."5 _-_0_._6 x 10"8 M _s_u_n; NGC 3607, M _B_H = 1.2"+"0"."4 _-_0_._4 x 10"8 M _s_u_n; NGC 4026, M _B_H = 2.1"+"0"."7 _-_0_._4 x 10"8 M _s_u_n; and NGC 5576, M _B_H = 1.8"+"0"."3 _-_0_._4 x 10"8 M _s_u_n, all significantly excluding M _B_H = 0. For NGC 3945, M _B_H = ...

2009-04-20

258

Characterization of projected DWPF glasses heat treated to simulate canister centerline cooling  

Energy Technology Data Exchange (ETDEWEB)

Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. The glass will be produced and poured into stainless steel canisters in the Defense Waste Processing Facility (DWPF). Eventually these canistered waste forms will be sent to a geologic repository for final disposal. In order to assure acceptability by the repository, the Department of Energy has defined requirements which DWPF canistered waste forms must meet. These requirements are the Waste Acceptance Preliminary Specifications (WAPS). The WAPS require DWPF to identify the crystalline phases expected to be present in the final glass product. Knowledge of the thermal history of the borosilicate glass during filling and cooldown of the canister is necessary to determine the amount and type of crystalline phases present in the final glass product. Glass samples of seven projected ...

1992-05-01

259

Report on the Second International Workshop on Human Chromosome 9  

Energy Technology Data Exchange (ETDEWEB)

The Second International Workshop on Human Chromosome 9 was held in Chatham, Massachusetts on April 18--20, 1993. Fifty-three abstracts were received and the data presented on posters. The purpose of the meeting was to bring together all interested investigators working on the map of chromosome 9, many of whom had disease-specific interests. After a brief presentation of interests and highlighted results, the meeting broke up into the following subgroups for production of consensus maps: 9p; 9cen-q32; 9q32 ter. A global mapping group also met. Reports of each of these working groups is presented in the summary.

1993-12-31

260

Proceedings of the Areva Technical Days. Session 5  

Energy Technology Data Exchange (ETDEWEB)

This document presents the proceedings of the Areva technical days, presented during the session 5 the 9 and 10 december 2004, at Istanbul. It deals with the operations of the transmission and distribution division. With manufacturing facilities in over 40 countries and a sales network in over 100, Areva offers customers technological solutions for nuclear power generation and electricity transmission and distribution (the Group also provides interconnect systems to the telecommunications, computer and automotive markets). It provides five topics: a general presentation of Areva, the strategic stakes for transmission and distribution by world-zone, economic and strategic stakes of business unit products, business unit systems and business unit automation. (A.L.B.)

2004-07-01

261

Effects of climate change on the production and consumption of electricity in Finland  

Energy Technology Data Exchange (ETDEWEB)

In the next few decades, the probable strengthening of the greenhouse effect may bring about considerable changes in energy production and consumption, which depend on climate. It is presumed that some of the changes will occur even if the rise in greenhouse gas concentration will be reduced. Because the investments in energy production have a long-term influence, decision-makers should have an idea about the impact of the strengthening of the greenhouse effect on energy production and consumption in Finland. According to the results of this study, the effects of climate change on the total consumption and production of electricity will be limited. The structure of both electricity consumption and production will remain rather similar, the most important changes applying to hydro power. The consumption of heating electricity will decrease substantially. Because the non- ...

1996-12-31

262

Large turbine, central power generation on offshore production facilities  

Energy Technology Data Exchange (ETDEWEB)

A case study of a hypothetical offshore production fixed leg platform facility is presented. The purpose of the case study is to demonstrate the advantages offered by modern, fuel efficient large gas turbines in central power generation service for offshore production. The case study was presented using the Rolls- Royce RB211 large gas turbine with facility production of approximately 240,000 BPD of oil and 540 MMSCFD of associated gas. The gas was subjected to three stages of separation for removal of hydrocarbon liquids and water. The liquids, natural gas, and crude oil were exported from the production platform to an onshore receiving terminal. Gas compression is the service that requires the greatest amount of power for any given production facility. For this case study, gas compression represented approximately 70 per cent of the power ...

2005-07-01

263

Wilsonville Advanced Coal Liquefaction Research and Development Facility, Wilsonville, Alabama. Technical progress report, Run 245 with Illinois 6 coal  

Science.gov (United States)

This report presents the operating results for Run 245 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an all-distillate Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary run objective was to obtain steady-state ITSL performance by replacing spent HTR reactor catalyst with fresh, sulfided catalyst. Secondary objectives were to maintain an all-distillate (minimum resid production) product slate and to demonstrate the effects of catalyst addition on the net gas production and hydrogen consumption. Run 245 began on 7 November, 1983, and continued through 12 February, 1984. During this period, 179.0 tons of coal was fed in 2045 hours of operation. Eight special product workup material balances were defined, and the results are presented herein. 6 references, 28 ...

1984-10-01

264

Temperature histories in geothermal wells: survey of rock thermomechanical properties and drilling, production, and injection case studies  

Energy Technology Data Exchange (ETDEWEB)

Thermal and mechanical properties for geothermal formations are tabulated for a range of temperatures and stress conditions. Data was obtained from the technical literature and direct contacts with industry. Thermal properties include heat capacity, conductivity, and diffusivity. Undisturbed geothermal profiles are also presented. Mechanical properties include Youngs modulus and Poisson ratio. GEOTEMP thermal simulations of drilling, production and injection are reported for two geothermal regions, the hot dry rock area near Los Alamos and the East Mesa field in the Imperial Valley. Actual drilling, production, and injection histories are simulated. Results are documented in the form of printed GEOTEMP output and plots of temperatures versus depth, radius, and time. Discussion and interpretation of the results are presented for drilling and well completion design to determine: wellbore temperatures ...

1981-07-01

265

Solar energy utilization and microcomputer control in the greenhouse builk curing and drying solar system  

Energy Technology Data Exchange (ETDEWEB)

Three agricultural applications in a specially designed greenhouse solar system functioning as a multi-purpose solar air collector for crop production and curing/drying processes are examined. An automated hydroponic crop production system is proposed for the greenhouse solar system. Design criteria of the proposed system and its utilization of solar energy for root-zone warming are presented and discussed. Based upon limited testing of the hydroponic system considered, hydroponic production of greenhouse crops is believed reasonable to complement the year-round use of the greenhouse solar system. The hardware/software design features of a microcomputer-based control system applied in the greenhouse solar barn are presented and discussed. On-line management and utilization of incident solar energy by the microcomputer system are investigated for both the greenhouse and tobacco ...

1987-01-01

266

Recent advances in analytical determination of cisplatin and its hydrolysis products  

International Nuclear Information System (INIS)

Cisplatin (cis-diaminedichloroplatinum [II] is a coordination compound, used in the treatment of several solid tumors. Cisplatin and its hydrolysis products exhibit a great pharmacological effect but are very toxic and probably carcinogenic. The present review summarizes the most important advances in the last years in the techniques employed for the detection and quantification of cisplatin and its hydrolysis products and in the different matrixes studied. The new emerging techniques and their modifications recently developed, fundamentally the combined use of detection and separation techniques for the analysis of platinum species and their impact on the speed, sensitivity and specificity of the analytical determination, with regard to the techniques used in the last century are discussed. High-Performance Liquid Chromatography and Capillary Electrophoresis, coupled with detection methods such as Mass Spectrometry, ...

2009-01-01

267

Optimization of water injection into vapor-dominated geothermal reservoirs  

Energy Technology Data Exchange (ETDEWEB)

Water injection into a vapor-dominated geothermal reservoir is an effective method of sustaining steam production from the field. Injection puts additional water to the reservoir and raises the prevailing reservoir pressure. This process improves the field`s productivity. However, the increased pressure also increases the water retention capacity of the reservoir rocks through the effects of adsorption and capillary condensation. Due to the significant costs associated with water injection programs, optimizing injection not only involves maximizing the energy yield from the resource but also the present worth of the project. Two crucial parameters that need to be established are: (1) how much to inject; and, (2) when to inject it. This study investigated the optimal design of these parameters. It was found that comparable energy yield can be attained for injection programs that are initiated at various stages of the field`s ...

1996-12-31

268

ZZ GEFF-2-MATXS, Coupled Neutron-Gamma Fusion Neutronics Library in MATXS Format  

International Nuclear Information System (INIS)

1 - Description of program or function: This library for fusion neutronics calculations, to be used in conjunction with the TRANSX code, is the MATXS format version of ZZ-GEFF-2-GENDF from which it has been derived by means of the MATXSR NJOY module. It has a 175 neutron, 42 photon VITAMIN-J group structure with the standard weighting function: Maxwellian (at the temperature to which the material is referenced) + 1/E + fission spectrum + 1/E + fusion peak + 1/E. It includes 93 materials from 1-H-1 to Bi-209 - almost all from EFF-2 basic data; but Ag-107, Ag-109, natural Cd, the 6 Hf isotopes and the 4 W isotopes have been taken from JEF-2.2 - at 3 temperatures and 6 dilution cross section values; 10 thermal groups are provided below 3 eV. Neutron cross sections and diffusion matrices, photon and gas production, kerma and DPA are given. The library includes H in H2O, metallic Be and Graphite for which an accurate treatment ...

1997-04-01

269

Effects of human serum on bacterial competition with neutrophils for molecular oxygen.  

Science.gov (United States)

A dialyzable factor(s) in human serum is known to stimulate gonococcal oxygen consumption. Its effect on other human pathogens was investigated. A 10% serum solution increased peak O2 consumption for Escherichia coli and Staphylococcus aureus to 157% (P less than 0.05) and 199% (P less than 0.02), respectively, of their O2 consumption when suspended in Hanks balanced salt solution, compared with a 356% increase for Neisseria gonorrhoeae with serum. Dialyzed serum lacked stimulatory capacity. Bacteria, serum, and neutrophils are often incubated to evaluate neutrophil bactericidal activity. Samples of 10(8) N. gonorrhoeae, S. aureus, and E. coli turned resazurin colorless (anaerobic conditions, Eh less than -42 mV) after 7.4, 13.3, and 15.1 min, respectively. Because neutrophil formation of reactive oxygen intermediates requires ambient O2, the effect of live bacteria and serum on this process was explored. After 5 min of incubation of 10(8) N. gonorrhoeae or S. aureus in 10% normal or ...

1986-06-01

270

Top Quark Physics with CMS  

CERN Document Server

Several signatures of new physics accessible at the LHC either suffer from top-quark production as a significant background or contain top quarks themselves. In this talk, we present results on top quark physics obtained from the first LHC data collected by the CMS experiment.They include measurements of the top pair production cross section in various channels and their combination, measurements of the top quark mass, the single top cross section, a search for new particles decaying into top pairs, and a first look at the charge asymmetry.

2011-01-01

271

The HARP experiment first physics results  

CERN Document Server

The HARP experiment at CERN is performing extensive measurements of hadron production cross sections and secondary particle yields, in the momentum range 1.5-15 GeV/c, over the full solid angle and using a large set of cryogenic and solid targets. First measurements of hadron production cross-sections in the forward region are reported using an aluminium target 5% of an interaction length thick and a proton beam of 12.9 GeV/c. A preliminary analysis in the large angle region of elastic scattering events produced with the cryogenic hydrogen target at 3 GeV/c beam momentum is also presented.

2005-01-01

272

Recent trends in coal liquefaction research and development  

Energy Technology Data Exchange (ETDEWEB)

The author outlines the special features of several coal liquefaction processes and describes their present stage of development. The following processes are reviewed: the SRC, EDS and H-Coal processes, the new IG process, and the BCL and NEDOL processes. The type of products resulting from coal liquefaction are discussed and explanations given of their yields. Finally, the characteristics of coal liquids are compared with those of petroleum-derived products, and the author outlines the nature of a chemical industry based on coal liquids as feedstocks. 9 references, 4 figures, 6 tables.

1986-01-01

273

Quality and availability of actinide isotopes from the All-Russian Scientific Research Institute of Experimental Physics in Arzamas-16  

International Nuclear Information System (INIS)

This paper describes the problems and capabilities of highly enriched actinide isotopes production by electromagnetic separation in the S-2 mass separator of VNIIEF. Isotope enrichment characteristics for uranium, plutonium, americium and curium isotopes, used in different nuclear physics experiments, and isotope contamination for single and double separations are presented. The capabilities for highly enriched "2"4"4Pu and "2"4"8Cm production for nuclear accelerator experiments and other applications are described, some details of the current and future programmes are given and the transport packaging is described. (orig.).

274

QCD CORRECTIONS TO DILEPTON PRODUCTION NEAR PARTONIC THRESHOLD IN PP SCATTERING.  

Energy Technology Data Exchange (ETDEWEB)

We present a recent study of the QCD corrections to dilepton production near partonic threshold in transversely polarized {bar p}p scattering, We analyze the role of the higher-order perturbative QCD corrections in terms of the available fixed-order contributions as well as of all-order soft-gluon resummations for the kinematical regime of proposed experiments at GSI-FAIR. We find that perturbative corrections are large for both unpolarized and polarized cross sections, but that the spin asymmetries are stable. The role of the far infrared region of the momentum integral in the resummed exponent and the effect of the NNLL resummation are briefly discussed.

2005-10-02

275

Proton beam monitoring and forming on the target of isotope complex at INR linac  

International Nuclear Information System (INIS)

Special beam extraction channel is used at INR linac for isotope production. It starts from 160 MeV measuring and matching area of accelerator. This choice of beam extraction enables to direct to the target of isotope complex a proton beam of wide energy range up to 160 MeV. It is important for production of different types of nuclides. The measuring results of proton beam behavior in this region are presented. Required beam forming in 160 MeV measuring and matching area of accelerator and in beam extraction channel is discussed.

2010-01-01

276

Production of polarized negative ion beams by collisional pumping  

Energy Technology Data Exchange (ETDEWEB)

The production of polarized negative ion beams by collisional pumping is described. Collisional pumping utilizes repeated charge changing collisions in a thick electron-spin-polarized gas or vapor target to form a polarized fast atom beam. The polarized fast atom beam is then partially converted into a polarized negative ion beam in a vapor target. Analysis is presented for a hydrogen beam passing through either a thick polarized H atom target or a thick polarized alkali target. Large polarizations and large currents may be possible.

1983-01-01

277

Production of polarized negative ion beams by ''collisional pumping''  

Energy Technology Data Exchange (ETDEWEB)

The production of polarized negative ion beams by ''collisional pumping'' is described. Collisional pumping utilizes repeated charge changing collisions in a thick electron-spin-polarized gas or vapor target to form a polarized fast atom beam. The polarized fast atom beam is then partially converted into a polarized negative ion beam in a vapor target. Analysis is presented for a hydrogen beam passing through either a thick polarized H atom target or a thick polarized alkali target. Large polarizations and large currents may be possible.

1984-03-01

278

Production of Group IIA atomic and molecular negative ion beams in a cesium-sputter negative ion source  

Energy Technology Data Exchange (ETDEWEB)

The results of an investigation on the production of Group IIA atomic and molecular negative ion beams formed in a cesium-sputter negative ion source are presented. The sputtering material was formed by pressing pellets of stoichiometric mixtures of the Group IIA element carbonates and 10% copper powder. Negative ions of several alkaline-earth elements and their oxides have been observed. Beam intensities as high as 180 pA have been observed for Sr{sup -}and 20 nA for SrO{sup -}. (orig.).

1996-09-11

279

Production of Group IIA atomic and molecular negative ion beams in a cesium-sputter negative ion source  

International Nuclear Information System (INIS)

The results of an investigation on the production of Group IIA atomic and molecular negative ion beams formed in a cesium-sputter negative ion source are presented. The sputtering material was formed by pressing pellets of stoichiometric mixtures of the Group IIA element carbonates and 10% copper powder. Negative ions of several alkaline-earth elements and their oxides have been observed. Beam intensities as high as 180 pA have been observed for Sr"-and 20 nA for SrO"-. (orig.).

1996-09-01

280

Proceedings of the Canadian Society for Bioengineering CSBE/SCGAB 2009 annual general meeting and technical conference  

Energy Technology Data Exchange (ETDEWEB)

This conference was attended by experts on current issues in engineering of an urban ecosystem, composting, biofuels and green energy. The meeting provided a forum to discuss advances in the application of engineering principles and practices dealing with biological systems for the production of food, bioproducts and energy. The discussions focused on engineering practices in agriculture, forestry, bioresources, biochemistry and biosystems. The 7 technical sessions of the conference were entitled: aquaculture; safety and training; bioprocessing; energy production and biofuels; environment and ecology; soil and water; and development of technologies. The conference feature 58 presentations, of which 9 have been catalogued separately for inclusion in this database. refs., tabs., figs.

2009-07-01

281

Optimal generation planning for a thermal system with pumped-storage based on analytical production costing model  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a new algorithm for the optimal long-range generation planning for a thermal system with pumped-storage plants. The algorithm is based upon the analytical production costing model developed under the assumption of Gaussian probabilistic distribution of random load fluctuations and plant outages. The optimization problem consists of the master problem to determine the annual investment, and the pumped-storage subproblem to determine the optimal pumped-storage operation. The master problem is formulated as a Hamiltonian minimization problem, and the pumped-storage subproblem is solved using the concept of peak-shaving operation on the original load curve.

1986-01-01

282

Optimal generation planning for a thermal system with pumped-storage based on analytical production costing model  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a new algorithm for the optimal long-range generation planning for a thermal system with pumped-storage plants. The algorithm is based upon the analytical production costing model developed under the assumption of Gaussian probabilistic distribution of random load fluctuations and plant outages. The optimization problem consists of the master problem to determine the annual investment, and the pumped-storage subproblem to determine the optimal pumped-storage operation. The master problem is formulated as a Hamiltonian minimization problem, and the pumped-storage subproblem is solved using the concept of peak-shaving operation on the original load curve.

1987-05-01

283

Measuring the beam polarizations and the luminosity at photon-photon colliders  

Energy Technology Data Exchange (ETDEWEB)

We present methods to measure the beam polarizations and the luminosity of [gamma][gamma] colliders at TeV energy scale. The beam polarizations of a [gamma][gamma] collider can easily be monitored by comparing the numbers of events of the processes [gamma][gamma] [yields] l[sup +]l[sup -] and [gamma][gamma] [yields] W[sup +] W[sup -], where l means e or [mu]. The luminosity of a [gamma][gamma] collider is also measurable by the event rate of W boson pair productions and the light lepton pair productions. (orig.)

1993-11-01

284

Indirect liquefaction contractors' review meeting: Proceedings  

Science.gov (United States)

The Eighth Indirect Liquefaction Contractors' Review Meeting was held November 15-17, 1988 at the Pittsburgh Hyatt Hotel. Twenty-eight presentations were made by contractors, invited speakers, and Pittsburgh Energy Technology Center R and D personnel. Six areas of research were covered: synthesis gas conversion to oxygenates; light hydrocarbon gas conversion; slurry reactor hydrodynamics; production, clean-up and conversion to hydrocarbon fuels; Fischer-Tropsch products upgrading; and, synthesis gas bioconversion. The meetings also included a panel discussion on direct methane conversion research. Individual projects are processed separately for the data bases.

1988-01-01

285

GaP Project: #gamma#p, #gamma#e, #gamma##gamma# colliders physical programs and CompHEP computer system  

International Nuclear Information System (INIS)

The Gamma Physics (GaP) program of physical phenomena investigation is proposed on #gamma#p, #gamma#e and #gamma##gamma# colliders at TeV energies. The program contains specialized software (CompHEP system) created for automation of particle interaction processes calculations in the framework of various gauge models. Preliminary physical results are presented (heavy quark production, W, Z production, supersymmetry etc.), and further software development is suggested. (R.P.) 22 refs., 8 figs., 4 tabs.

286

Estimation of armature condition in concrete with gamma-absorption method  

International Nuclear Information System (INIS)

Bases of the algorithm for assessing the reinforcement status in reinforced concrete products by gamma-absorption method are presented. Analytical equations are obtained for estimation of error of the parameter characterizing the degree of reinforcement destruction. It is recommended to use high-energy Bremsstrahlung sources-betatrons of 4-10 MeV maximum energy for testing products of 500-600 mm thick. Linear radiation attenuation factor (LAF) of concrete in estimated equation is replaced by effective LAF of concrete, and LAF of reinforcement and corrosion materials - by differential LAF. Corresponding LAF of nonevident form in the algorithm is assessed by the results of processing of direct-shadow radiographs of defectometers

287

Effect of improved target designs on the "2"3"8Pu production at the Fast Flux Test Reactor  

International Nuclear Information System (INIS)

This paper present the results of a series of calculations made to determine the "2"3"8Pu production potential of several advanced target assembly designs in the Fast Flux Test Facility (FFTF). These calculations show that by using advanced target designs the intimately mix the "2"3"7Np target material with an yttrium hydride moderator, the FFTF has the potential of producing up to 30 kg of high-quality "2"3"8Pu per year.

1991-11-10

288

Correlation between Magnetic Field Quality and mechanical components of the Large Hadron Collider Main Dipoles  

CERN Document Server

The homogeneity of the magnetic field in the LHC dipoles strongly depends on the correct position of the superconducting cables: this is related to the quality of the dipole components, such as the dimension of the coil spacers (copper wedges), of the cable and of the collars. The performance in operational conditions is also affected by the magnetization of the cables. In this work, we analyse the measurements of these quantities during the production of the 1276 LHC dipoles, their trends, and the relation to the measured magnetic field. A novel mtehod to locate electrical shorts based on the analysis of magnetic measurements is also presented, and applications to 15 dipoles reascued during the production is given.

2006-01-01

289

Chemical and Process - EA BOOKS  

Wastenet

... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions Browse Product Pages My EA Books Customer sign in User name Password Forgot your password? Register Mailing Lists New Books - Promotions click here to subscribe Shopping basket 50 Products AU$5,482.58 Standard Post Australia AU$10.00 Total amount AU$5,492.58 Display shopping basket Check out Copyright ©Engineers Media 2008 Terms &...

290

Australasia floating production storage offloading`s (F.P.S.O.) push  

Energy Technology Data Exchange (ETDEWEB)

Floating Production, Offshore Storage and Offloading (FPSO) of hydrocarbons is not new. However, offshore crude oil development has to face the increasing need of the geopolitical interests to develop smaller or difficult reservoir in remote areas in deeper water and harsher environment. Such a trend can only be sustained if the offshore technology provides the right tools at the right time and at an acceptable price. This article will attempt to describe the relative merits of FPSO systems and discuss its main components. An overview of the present world situation shows the excellent performance of the FPSO with the type of development strategy undertaken in P.R.C.

1993-12-31

291

Applications of solar heat in agriculture and industry  

Energy Technology Data Exchange (ETDEWEB)

The production of process heat for agriculture and industry is one of the applications of solar energy which is very close to economic competitivity. Solar collectors can be produced at a reasonable cost by existing industries and are used optimally through applications which present a good time correlation between energy needs and the possible production of solar heat. This article studies heat consumption in industrial and agricultural sectors, gives hints on collectors choices, rates the different projects by simulation taking into account the nature of agricultural and industrial activities and the geographical location of the projects, examines when the equipment first competes according to hypotheses made on the various energy and collectors cost.

1980-01-01

292

Anomalous single production of fourth generation $t'$ quarks at ILC and CLIC  

CERN Document Server

We present a detailed study of the anomalous single fourth generation $t'$ quark production within the dominant Standard Model(SM) decay modes at future $e^+e^-$ colliders. We calculate the signal and background cross sections in the mass range 300-800 GeV. We also discuss the limits of $t'q\\gamma$ and $t'qZ$ ($q=u,c$) anomalous couplings as well as values of attainable integrated luminosity for 3$\\sigma$ observation limit.

2011-01-01

293

A new technique for production of yellow cake with double precipitation  

International Nuclear Information System (INIS)

The author presents a new technique for production of yellow cake with double precipitation, thus solving a series of problems for precipitating uranium with traditional double precipitation. The new technique can not only remove ferric ions and sulfate radicals but also make solid-liquid separation easy, utilize effectively the sulfuric acid produced in ferric ions precipitation process, and increase uranium concentration of leaching liquor. To take it as producing yellow cake will save investment, simplify operation, and cut down the consumption of raw materials and energies. It is more competitive than ion-exchange or solvent extraction in the process of extracting-purifying and preparing yellow cake.

1997-01-01

294

A fast production scheduler for generation expansion planning in a hydro-thermal system  

Energy Technology Data Exchange (ETDEWEB)

A fast production scheduling algorithm suitable for generation expansion studies is described in this paper. It can handle several independent rivers, thermal plants, pumped storage plants, import, export, and internal non-firm markets. Inflows and load are deterministic and a one-reservoir limit is imposed on each river. The scheduling problem is formulated as a generalized network problem which is efficiently solved by an adaption of the simplex method. The algorithm is part of a program developed by Hydro-Quebec to conduct preliminary evaluations of alternative expansion plans. The program and the scheduling algorithm are presented.

1986-01-01

295

A fast production scheduler for generation expansion planning in a hydro-thermal system  

Energy Technology Data Exchange (ETDEWEB)

A fast production scheduling algorithm suitable for generation expansion studies is described in this paper. It can handle several independent rivers, thermal plants, pumped storage plants, import, export, and internal non-firm markets. Inflows and load are deterministic and a one-reservoir limit is imposed on each river. The scheduling problem is formulated as a generalized network problem which is efficiently solved by an adaption of the simplex method. The algorithm is part of a program developed by Hydro-Quebec to conduct preliminary evaluations of alternative expansion plans. The program and the scheduling algorithm are presented.

1987-02-01

296

Plastic wastes as support fuel. Jaetemuovin kaeyttoe tukipolttoaineena  

Energy Technology Data Exchange (ETDEWEB)

The association of Finnish Plastics Industry examined the possibilities to utilize energy content of plastic wastes in spring 1990. A bark fuelled boiler plant of forest industry was used as test power plant. The power of the plant was 60 Mw. This report discusses shortly the theory of combustion of plastics. About 130 000-15 000 tons of plastic waste, corresponding to 7 % of the solid municipal waste, is dumped annually in Finland. Utilization of the plastic waste recovered from municipal wastes for energy production is technically viable in present power plants among present energy production. The chipping and mixing of the plastic in the other fuel are the only pretreatment required for the plastic waste. In Finland there are several power plants using suitable fuels for plastic mixture combustion. The portion of the plastic of the total fuel power was 10 %. No problems occurred during the tests. The ...

1991-01-01

297

W, Z and H bosons in the three particle final states production at TeV energy #gamma#e and #gamma##gamma#colliders  

International Nuclear Information System (INIS)

The short review of complete tree level calculations for three particle final states production at the future e"+e"-, #gamma#e and #gamma##gamma# colliders is presented. The results obtained with the help of CompHEP system for total cross sections and other characteristics of processes in the energy range 0.1-2 TeV are summarized and their comparison with the results of different approaches is discussed. In particular we are interested in the processes of W, Z and H boson production. The reactions under consideration are especially interesting in connection with probing of new couplings, searching for new particle signals and as an important backgrounds to these experiments. The main subjects described are basic reactions rates (sections 2,3), Higgs production in #gamma#e collisions (section 4), the possibilities of testing some four vector bosons interaction vertices and Higgs-fermion coupling (section ...

1993-12-01

298

Radioisotope production in the I.Ph.P.E. cyclotron for medical application  

International Nuclear Information System (INIS)

The production methods for seven radioisotopes, Ga-67, Sr-85, Pd-103, In-111, Tu-167, Hg-197 and Pb-203, by using a classical 1.5m cyclotron in the Institute of Physics and Power Engineering, Obninsk, USSR, are described. At present, more than 50 cyclotrons in different countries are used for the production of radioisotopes applied to medicine. Radioisotopes are produced with the cyclotron in the I.Ph.P.E. in the form of irradiated targets, which are delivered to Moscow radiopharmaceutical factory, where radiopharmaceuticals are produced on the base of these targets. The cyclotron is operated in two regimes providing the acceleration of protons, deuterons and alpha -particles. Two types of target assemblies are used for irradiation, the one is intended for the internal beam, and the other is for the external beam. The reactions used for the production of seven radioisotopes described above, the types of ...

299

Radioisotope production in the I. Ph. P. E. cyclotron for medical application  

Energy Technology Data Exchange (ETDEWEB)

The production methods for seven radioisotopes, Ga-67, Sr-85, Pd-103, In-111, Tm-167, Hg-197 and Pb-203, by using a classical 1.5m cyclotron in the Institute of Physics and Power Engineering, Obninsk, USSR, are described. At present, more than 50 cyclotrons in different countries are used for the production of radioisotopes applied to medicine. Radioisotopes are produced with the cyclotron in the I.Ph.P.E. in the form of irradiated targets, which are delivered to Moscow radiopharmaceutical factory, where radiopharmaceuticals are produced on the base of these targets. The cyclotron is operated in two regimes providing the acceleration of protons, deuterons and alpha -particles. Two types of target assemblies are used for irradiation, the one is intended for the internal beam, and the other is for the external beam. The reactions used for the production of seven radioisotopes described above, the types of ...

1982-01-01

300

Particle production in nuclear collisions and dissociation of nuclei into nucleons  

International Nuclear Information System (INIS)

An attempt to classify experimental data and to present new approach for the problem of cumulative production of particles and high-transverse momentum particles (#pi#"#+-#, k"#+-#, p, p-bar, d) on Li"6, Be, Mg, Si, "5"4","5"6","5"8Fe, "5"8","6"1","6"4Ni, Cu, "6"4Zn, "1"1"2","1"1"8","1"2"4Sn, "1"4"4","1"5"4Sm, "1"8"2","1"8"6W, U nuclei is made in the review. Particle cumulative production, quark-parton structure function, A dependence of particle production on nuclei and in nuclear collisions and A dependence of inclusive cross sections of particle cumulative production are discussed. Reactions with dissociation on nucleons of deuteron, helium and compound nuclei are considered. Possibility of unified description of different processes is discussed in terms of nucleus flucton model. 35 refs.; 22 figs.

1988-06-14

301

One-loop Higgs boson production at the Linear Collider within the general two-Higgs-doublet model: e+e- versus gamma-gamma  

CERN Document Server

We present an updated overview on the phenomenology of one-loop Higgs boson production at Linear Colliders within the general Two-Higgs-Doublet Model (2HDM). First we report on the Higgs boson pair production, and associated Higgs-Z boson production, at O(alpha^3_{ew}) from e+e- collisions. These channels furnish cross-sections in the range of 10-100 fb for Ecm=0.5 TeV and exhibit potentially large radiative corrections (of order 50%), whose origin can be traced back to the genuine enhancement capabilities of the triple Higgs boson self-interactions. Next we consider the loop-induced production of a single Higgs boson from direct gamma-gamma scattering. We single out sizable departures from the corresponding rates in the Standard Model, which are again correlated to trademark dynamical features of the 2HDM -- namely the balance of the non-standard Higgs/gauge, Higgs/fermion and ...

2011-01-01

302

Methodology for optimal selection of cutoff grades and production rates of underground uranium mining operations  

Energy Technology Data Exchange (ETDEWEB)

The optimizing criterion is assumed to be the maximum net present value of the project. The following summarizes the significant conclusions. (1) Over a large range of discount rates, mining and milling of the mineral deposit at a constant cutoff grade and a constant production rate consistently results in smaller annual discounted cash flows than the optimal schedule determined by the dynamic programming model (dpm) where the cutoff grade and mining rate are allowed to vary in response to fluctuating product price. (2) With an increasing discount rate, under the dpm the annual discounted cash flows decrease at a slower rate than if the mineral inventory is mined and milled at a constant cutoff grade and a constant production rate. (3) Cuttoff grade increases only where higher equity ore is available. Thus, to maintain the mill feed requirement, the mining rate also increases. (4) Not withstanding an ...

1986-01-01

303

Linear chain tensioning of moored production vessels  

Energy Technology Data Exchange (ETDEWEB)

As need for development of marginal and deepwater oil fields grows, demand increases for floating production vessels (FPVs) such as floating production, storage and offloading (FPSO) units; spread-moored production semi-submersibles; and turret-moored production vessels. The FPV may be purpose-built; or an existing vessel such as an exploration drilling semi-sub or ship-shape vessel may be modified to suit the purpose. In either case, requirements for tensioning systems for the mooring lines on the FPV are quite unique, and are not without the potential for problems when traditional chain windlasses or wire rope systems are employed. This two-part article discusses the range of available technologies and systems for tensioning mooring lines on FPVs. It examines problems of size, weight and safety associated with some available designs; and it considers in detail a specific family of new units. Part 1, ...

1993-04-01

304

Determination of the minor disinfection by-products formed in the water plant of Sant Joan Despi (Barcelona, Spain); Determinacion de los subproductos de desinfeccion minoritarios formados en la planta de Sant Joan Despi (Barcelona)  

Energy Technology Data Exchange (ETDEWEB)

Chlorine is widely used in drinking water disinfection due to be a powerful and not expense disinfection. Although the benefits of disinfection, the formation of stable disinfection by-products of the health concern, is the result of the interaction of aqueous chlorine with natural organic matter presents in water. Disinfection by-products generated in major concentration are trihalomethane and haloacetic acids. Disinfection by-products generated in minor concentration are haloacetonitriles, haloketones,chloral hydrate and chloropicrin and some new groups such as cyanogen halides and trihaloacetaldydes. In this work two analytical methods.: headspace/gas chromatography/electron capture detector and liquid-liquid microextraction/gas chromatography/electron capture detector are studied and compared to determine the minor by-products and to establish finally, a systematic control of ...

1997-09-01

305

Climate Change and Agricultural Vulnerability  

Energy Technology Data Exchange (ETDEWEB)

After the introduction Chapter 2 presents details of the ecological-economic analysis based on the FAO/IIASA agro-ecological zones (AEZ) approach for evaluation of biophysical limitations and agricultural production potentials, and IIASA's Basic Linked System (BLS) for analyzing the world's food economy and trade system. The BLS is a global general equilibrium model system for analyzing agricultural policies and food system prospects in an international setting. BLS views national agricultural systems as embedded in national economies, which interact with each other through trade at the international level. The combination of AEZ and BLS provides an integrated ecological-economic framework for the assessment of the impact of climate change. We consider climate scenarios based on experiments with four General Circulation Models (GCM), and we assess the four basic socioeconomic development pathways and emission scenarios as ...

2002-08-01

306

Use of radiosensitivity to identify irradiated fresh poultry products  

International Nuclear Information System (INIS)

Microbiological comparison between irradiated and non-irradiated foodstuff has been studied for a long time as a way to detect whether a foodstuff has been irradiated or not. Generally, the proposed methods are based on the fact that ionization select species of bacteria which are recognized to be radioresistant. So reduction or elimination of known radiation sensitive microbes from the normal endogenous microflora could give an indication that the foodstuff has been irradiated, predominance of known radioresistant bacteria should be another indication. In the present work, we try to develop a test based on the radiosensitivity of the bacteria independently of their place. These first experiments show that the determination of radiosensitivity of strains isolated from a product or even of global radioresistance of mesophilic microflora could indicate if this product has been previously submitted to ionizing radiations. (4 ...

1990-02-14

307

Theoretical study of the non-steady discharge at atmospheric pressure in pin-plate system and its application for ozone production  

International Nuclear Information System (INIS)

In this paper as a result of the theoretical studies and a numerical simulation we presented the following main conclusions: (i) for humid air at increasing pressure of 1.0133 10"5 Pa until 5.0665 10"5 Pa ozone concentrations during 2 centre dot 10"-"3 s become higher in 22 times. This fact we clear with structure of ozone-production reactions. In this case the harmful NO_x concentrations are 2-3 order lower than ozone one; (ii) it is shown that nitrogen is useful to ozone production in the discharge; (iii) based on ion collection we cleared increasing ignition discharge voltage at growing ozone concentrations even with low ozone concentrations.

308

Study of the $pp \\to np\\pi^+$ reaction at 1.25 GeV with HADES  

CERN Document Server

In pp collisions at 1.25 GeV kinetic energy, the HADES collaboration aimed at investigating the di-electron production related to $\\Delta$ (1232) Dalitz decay ($\\Delta^+ \\to pe^+e^-$). In order to constrain the models predicting the cross section and the production mechanisms of $\\Delta$ resonance, the hadronic channels have been measured and studied in parallel to the leptonic channels. The analyses of $pp\\to np\\pi^+$ and $pp\\to pp\\pi^0$ channels and the comparison to simulations are presented in this contribution, in particular the angular distributions being sensitive to $\\Delta$ production and decay. The accurate acceptance corrections have been performed as well, which could be tested in all the phase space region thanks to the high statistic data. These analyses result in an overall agreement with the one-$\\pi$ exchange model and previous data.

2009-01-01

309

South African consumers' opinions and consumption of soy and soy products  

British Library Electronic Table of Contents (United Kingdom)

Abstract Interest in soy foods has increased with consumer awareness of its health benefits, especially with soy-related ingredients being utilized as one of the major sources of high-protein fortification. The aim of the present study was to assess South African (SA) consumers' opinion of soy and soy products through different statements on consumption, taste, protein value and healthiness. The respondents (n = 3001) for this randomized cross-sectional study were randomly selected from metropolitan and rural areas in South Africa. Trained fieldworkers administered questionnaires by conducting face-to-face interviews. Fourteen statements from four sections of the questionnaire (consisting of 17 food-related topics in total), probing information on consumers' opinion on soy and soy products...

2009-01-01

310

Shutdown Chemistry Process Development for PWR Primary System  

Energy Technology Data Exchange (ETDEWEB)

This study report presents the shutdown chemistry of PWR primary system to reduce and remove the radioactive corrosion products which were deposited on the nuclear fuel rods surface and the outside of core like steam generator channel head, RCS pipings etc. The major research results are the follows ; the deposition radioactive mechanism of corrosion products, the radiochemical composition, the condition of coolant chemistry to promote the dissolution of radioactive cobalt and nickel ferrite, the control method of dissolved hydrogen concentration in the coolant by the mechanical and chemical methods. The another part of study is to investigate the removal characteristics of corrosion product ions and particles by the demineralization system to suggest the method which the system could be operate effectively in shut-down purification period. (author). 19 refs., 25 figs., 48 tabs.

1997-12-31

311

Scenario development for the optimization of energy production from waste materials in the Netherlands; Scenario-ontwikkeling voor de optimalisatie van energieproductie in Nederland  

Energy Technology Data Exchange (ETDEWEB)

The main purpose of the study on the title subject is to gain insight into the strategic options to optimize energy production from waste processing in the Netherlands in the long term. The developed optimization model will be used by the Dutch Ministry of Public Health, Spatial Planning en Environment (VROM) for scenarios to calculate and determine expectations and uncertainties in the development of waste processing in the Netherlands. Attention is paid to (1) the impact of present and future technology on the costs and energetic efficiency of waste processing, (2) several techniques for the generation of electricity and heat, the production of fuels, and recycling, (3) the impact of scale (capacity) on costs and energetic efficiency of waste processing installations, and (4) the impact of transport and heat distribution. The time frame is the year 2020. 66 refs.

2001-01-01

312

Quantitative and qualitative aspects of agricultural products  

International Nuclear Information System (INIS)

The following aspects will be discussed: The main function of the Division of Inspection Services and its role in the Marketing of agricultural products; the shelf life of agricultural products: short review of present methods with a practical example of losses incurred due to limited keeping quality; irradiation and heat treatment: advantages of inhibited microbiological activities and undesirable chemical changes from a quality control point of view; quality standards: the basic principles of quality control; consequences of effective post-harvest treatment: export of deciduous and citrus fruit; the magnitude of the problem of poor keeping quality and quality requirements; other fruit; quantities and export limitations and vegetables; quantity and quality requirements; local marketing: fruit and vegetables subjected to inspection; quantity and quality aspects.

313

Proceedings of the Canadian Society for Bioengineering CSBE/SCGAB 2006 national technical conference  

Energy Technology Data Exchange (ETDEWEB)

This conference provided a forum for discussing advances in the application of engineering principles and practices dealing with biological systems for the production of food, bioproducts and energy. The discussions focused on engineering practices in agriculture, forestry, bioresources, biochemistry and biosystems. The sessions of the conference were entitled: renewable energy and biofuels; food and bioproducts; odour and greenhouse gases; soil and water; waste management and bioresiduals; animal welfare and production; grain storage; machinery systems; structures and biocomposites; and, agricultural production. The conference also featured a workshop on modeling material and energy flows through agro-ecosystems. In addition to 22 posters, the conference featured 100 presentations, of which 8 have been catalogued separately for inclusion in this database. refs., tabs., figs.

2006-07-01

314

Pipelineable bitumen and heavy oil project  

Energy Technology Data Exchange (ETDEWEB)

Capital investment in extra heavy crude production is expected to increase from $6 billion to $25 billion by 2005. In response to this forecast, producers are focusing their efforts on improving the quality of extra heavy crude right at the production sites to reduce their dependence on diluent, reduce pipelining costs, and to receive a higher return for their investment. Their efforts would also minimize environmental impacts at production sites. This slide presentation also proposed a solution to the problem associated with stability and incompatibility of thermal upgrading by taking advantage of the inherent incompatibility of extra heavy crudes and paraffinic diluents and using diluents to perform selective decarbonization (or the partial removal of asphaltene) to reduce heavy crude viscosity and density. A pilot-scale test has been conducted and a bench-scale unit will be carried out in Fall 2000.

2000-07-01

315

Natural radioactive materials in oil and gas industry  

International Nuclear Information System (INIS)

Oil and gas production and processing operations sometimes cause naturally occurring radioactive materials (NORM) to accumulate at elevated concentrations in by-product waste streams. The sources of most of the radioactivity are isotopes of "2"3"8U and "2"3"2Th series, which are naturally present in the subsurface formations from which oil and gas are produced. NORM waste may cause problems in the operations of installations by plugging perforations, clogging tubular and valves then restricting flow. Therefore, plants or equipment have to be refurbished and decontaminated before reuse to avoid radioactive waste or surface contaminated object. There are two options for safe disposal of scale and sludge produced from NORM Descaling Facility : 1- Injection into an abandoned production well. 2- The construction of a near surface depository. These options are assumed to be environmental friendly disposal ...

2010-03-01

316

Model for risk and reliability analysis of complex production systems: Application to FPSO/flow-Riser system  

British Library Electronic Table of Contents (United Kingdom)

A model for risk and reliability analysis of complex multifunctional production process systems is presented. The model employs Monte-Carlo and Markov Chain algorithms that uses a weighted index to train and simulate the fuzzy hazard data sets which represents failure outcomes of risk component transient and non-transient systems. Early simulation results shows that hazard rates and the risk of containment loss from typical floating production and storage offloading (FPSO)-Riser system for the risk components in parallel or series increases exponentially with time and decreases as safety ratings fraction increases. The reliability value decreases with time and safety fraction (SFAC) for all fuzzy hazard classifications. The results of the computed mean time before repair (MTBR) show that t...

2009-01-01

317

Meson production in proton-proton collisions in the naive non-abelianization approximation and the role of infrared renormalons  

CERN Document Server

In this article, we investigate the "naive non-abelianization" (NNA) contributions of the higher-twist Feynman diagrams to the large-$p_T$ inclusive pion production cross section in proton-proton collisions and present the general formulae for the higher-twist differential cross sections in the case of the running coupling and frozen coupling approaches. We compared the resummed "naive non-abelianization" higher-twist cross sections with the ones obtained in the framework of the frozen coupling approach and leading-twist cross section. The structure of infrared renormalon singularities of the higher twist subprocess cross section and it's resummed expression (the Borel sum) are found. It is shown that the resummed result depends on the choice of the meson wave functions used in the calculations. We discuss the phenomenological consequences of possible higher-twist contributions to the meson production in proton-proton ...

2011-01-01

318

In vitro competitive adhesion and production of antagonistic compounds by lactic acid bacteria against fish pathogens  

British Library Electronic Table of Contents (United Kingdom)

The present study describes the screening of five lactic acid bacteria (LAB) for use as probiotics based on their competitive adhesion and production of antagonistic substances against some fish pathogens. A reduction of adhesion of all pathogenic strains tested was obtained with three of the LAB strains (Lactococcus lactis subsp. lactis CLFP100, Lactococcus lactis subsp. cremoris CLFP102 and Lactobacillus curvatus CLFP150). With the exception of fish pathogens Flavobacterium psychrophilum and Renibacterium salmoninarum that were not inhibited by LAB strains, production of antagonistic compounds by all tested LAB was observed against at least one of the indicator strains. Based on mucus adhesion, competitive exclusion, and suppression of fish pathogen growth, the selected LAB strains can b...

2007-01-01

319

Improvement of agricultural economics through integration of small scale heat and power production with non-food value-added products. Final report  

Energy Technology Data Exchange (ETDEWEB)

The primary objective of the work was to establish and verify cost and performance parameters for integrated concepts in which agricultural and other biomass derived pyrolysis oils are utilised as fuel for small scale heat and power production. Production of non-food value-added products was also considered. The cost and performance studies were carried out in Spain, Denmark, and Finland, using olive oil farming residues, straw, and rapeseed oil pressing residues and straw as fuels for pyrolysis, respectively. Use of forest residue wood fuel was also considered in the Finnish vase. A rather wide selection of biomasses was therefore studied within the project. The secondary objective was to generate experimental data to verify and support the critical features within these concepts. Experimental work, modelling, and techno-economic assessments were carried out within the project. The experimental part included: Determination ...

1997-07-01

320

Feasibility analysis for attosecond X-ray pulses at FERMI@ELETTRA free electron laser  

Energy Technology Data Exchange (ETDEWEB)

We present preliminary analysis for the feasibility of the attosecond x-ray pulses at a proposed FERMI@ELETTRA free electron laser (FEL) [1]. In part 1 we restrict ourselves to minimal modifications to the proposed FEL and consider a scheme for attosecond x-ray production which can be qualified as a small add-on to a primary facility. We demonstrate that at 5-nm wavelength our scheme is capable for production of pulses with an approximate duration of 100 attoseconds at approximately 2 MW peak power and with an absolute temporal synchronization to a pump laser pulse. In part 2 we propose to use an FEL amplifier seeded by a VUV signal and to follow it by the scheme for attosecond x-ray production described in part 1.

2004-09-01

321

Evaluation of carbon-14 (C{sup 14}) levels of terrestrial and marine food products of the environment of the site of Cogema La Hague; Evaluation des niveaux de carbone-14 ({sup 14}C) des denrees alimentaires terrestres et marines de l'environnement du site de COGEMA - La Hague  

Energy Technology Data Exchange (ETDEWEB)

This evaluation has for object to inform about the levels in carbon 14 in the environment of the factories of La Hague. Two sectors were differentiated on one hand the terrestrial environment, and on the other hand the marine environment. The investigations concerned first and foremost food products stemming as the vegetable culture (vegetables) or individual breeding (milk, eggs) but also foodstuffs stemming from the local agriculture (cereal). In touch with the second sector, the marine environment, the sampling concerned the accessible products of the sea by all and those locally marketed (fishes, molluscs, shellfishes). The different results are presented in tables. (N.C.)

2006-04-15

322

Coal quality engineering aids purchasing  

Energy Technology Data Exchange (ETDEWEB)

New York State Electric and Gas Co. (NYSEG) has developed a tool called Coal Quality Engineering Analysis (CQEA) to evaluate the cost impacts of coal quality on its power plants. CQEA allows quantification of the effect of coal quality on plant operating costs and has become an important factor in coal purchasing. The article describes the development of the analysis method, including a logic diagram of CQEA relationships. The results of CQEA calculations on the impact of one coal on overall production costs of different units, the impact of different coals on overall production costs of one unit, and production cost vs. coal quality, are presented and discussed. The use of the CQEA system within NYSEG is described.

1987-06-01

323

"Advanced" data reduction for the AMBER instrument  

CERN Document Server

The amdlib AMBER data reduction software is meant to produce AMBER data products from the raw data files that are sent to the PIs of different proposals or that can be found in the ESO data archive. The way defined by ESO to calibrate the data is to calibrate one science data file with a calibration one, observed as close in time as possible. Therefore, this scheme does not take into account instrumental drifts, atmospheric variations or visibility-loss corrections, in the current AMBER data processing software, amdlib. In this article, we present our approach to complement this default calibration scheme, to perform the final steps of data reduction, and to produce fully calibrated AMBER data products. These additional steps include: an overnight view of the data structure and data quality, the production of night transfer functions from the calibration stars observed during the night, the correction ...

2008-01-01

324

Formation of double hafnium sulfates in the systems HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4)  

International Nuclear Information System (INIS)

Influence of alkali elements on formation, composition, solubility and region of stability of complex hafnium sulfates, separated in the HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4 group) systems is studied. In all cases hafnium forms the complex sulfates of three types differing by basicity or ratio HfO"2:SO"3 1:1, 1:1.5, 1:2. Three basic and three medium sulfates are crystallized in the systems with sodium; with rubidium, cesium and ammonium - two basic and two medium sulfates and with potassium - two basic and one medium salts. Anhydrous salts do not form in the investigated systems. Potassium salt approximately 0.3% according to HfO"2 is characterized by minimum solubility from the salts of 2HfOSO"4x(1-3)Me"2SO"4x(4-6)xH"2O while solubility of the same salts with rubidium, cesium and sodium increases from (0.25-1.0); (0.5-1.5) till (1.0-5)% ...

1982-01-01

325

Effect of N_2 + H_2 gas mixtures in plasma nitriding on tribological properties of duplex surface treated steels  

International Nuclear Information System (INIS)

Thermo-reactive diffusion chromizing followed by pulsed plasma nitriding were carried out on AISI 52100 and 8620 bearing steels. The chromized samples were pulse-plasma nitrided for 5 h at 500 deg. C in various N_2-H_2 gas mixtures. The coated steels were characterized using scanning electron microscopy, X-ray diffraction and microhardness testing. The unlubricated wear behaviors of only chromized and duplex treated steels were investigated in ball-on-disc system tests at room temperature. X-ray diffraction patterns of the duplex treated samples containing H_2 indicated the formation of dominant CrN and Cr_2N nitrides as well as the formation of Cr_3C_2 and Cr_7C_3 carbides. Gas mixtures in the plasma nitriding, which was performed after chromizing, have a significant influence on the wear rate of the duplex treated steels. The wear and friction tests showed that the lowest friction coefficient and wear ...

2008-12-01

326

Comparative investigation on chemical looping combustion of coal-derived synthesis gas containing H2S over supported NiO oxygen carriers  

Energy Technology Data Exchange (ETDEWEB)

Chemical looping combustion (CLC) of simulated coal-derived synthesis gas was conducted with NiO oxygen carriers supported on SiO2, ZrO2, TiO2, and sepiolite. The effect of H2S on the performance of these samples for the CLC process was also evaluated. Five-cycle thermogravimetric analysis (TGA) tests at 800 C indicated that all oxygen carriers had a stable performance at 800 C, except NiO/SiO2. Full reduction/oxidation reactions of the oxygen carrier were obtained during the five-cycle test. It was found that support had a significant effect on reaction performance of NiO both in reduction and oxidation rates. The reduction reaction was significantly faster than the oxidation reaction for all oxygen carriers, while the oxidation reaction is fairly slow due to oxygen diffusion on NiO layers. The reaction profile was greatly affected by the presence of H2S, but there was no effect on the capacity due to ...

2010-01-01

327

ARM AND INTERARM STAR FORMATION IN SPIRAL GALAXIES  

International Nuclear Information System (INIS)

We investigate the relationship between spiral arms and star formation in the grand-design spirals NGC 5194 and NGC 628 and in the flocculent spiral NGC 6946. Filtered maps of near-IR (3.6 #mu#m) emission allow us to identify 'arm regions' that should correspond to regions of stellar mass density enhancements. The two grand-design spirals show a clear two-armed structure, while NGC 6946 is more complex. We examine these arm and interarm regions, looking at maps that trace recent star formation-far-ultraviolet (GALEX NGS) and 24 #mu#m emission (Spitzer SINGS)-and cold gas-CO (HERACLES) and H I (THINGS). We find the star formation tracers and CO more concentrated in the spiral arms than the stellar 3.6 #mu#m flux. If we define the spiral arms as the 25% highest pixels in the filtered 3.6 #mu#m images, we find that the majority (60%) of star formation tracers occur in the interarm regions; this result persists qualitatively even when considering the potential impact of finite data ...

2010-12-10

328

The assessment of soil conservation technologies for sustainable agricultural production. Report of the FAO/IAEA consultants meeting. Working material  

International Nuclear Information System (INIS)

A Consultants' Meeting on 'The assessment of soil conservation technologies for sustainable agricultural production' was held in Vienna at the IAEA Headquarters from May 28-30, 2001. The consultants' presentations reviewed recent advances in the use of fallout radionuclides to measure soil erosion as well as approaches and technologies applied for soil conservation worldwide. Also, activities and experiences of FAO and UNEP in the field of land degradation, soil conservation and related issues were presented. Based on the information provided by the Scientific Secretary, a full project proposal was prepared during the second part of the Consultants' Meeting. The consultants also provided recommendations on the formulation and implementation of a future CRP on the subject.

2001-05-28

329

Production of scalar Higgs and pseudoscalar Higgs in multi-Higgs doublet models at {gamma}{gamma} colliders  

Energy Technology Data Exchange (ETDEWEB)

We present the effects of heavy CP-even (H) and CP-odd (A) Higgs bosons on the production cross section of the process {gamma}{gamma}{yields}tt at the energy around the mass poles of the Higgs bosons. It is found that interference between H and A with small mass gap, as well as the ones between Higgs bosons and continuum, contributes to the cross section, if the photon beams are polarized and if we observe the helicity of the top quarks. It is demonstrated in the framework of the minimal supersymmetric extension of the standard model that the H and A contributions can be sizable at future {gamma}{gamma} colliders for small values of tan {beta}. The methods to measure the CP-parity of the Higgs boson are also presented. The statistical significance of detecting the Higgs signals and measuring the Higgs CP-parity is evaluated. (orig.)

2000-05-01

330

Production of scalar Higgs and pseudoscalar Higgs in multi-Higgs doublet models at #gamma##gamma# colliders  

International Nuclear Information System (INIS)

We present the effects of heavy CP-even (H) and CP-odd (A) Higgs bosons on the production cross section of the process #gamma##gamma##->#tt at the energy around the mass poles of the Higgs bosons. It is found that interference between H and A with small mass gap, as well as the ones between Higgs bosons and continuum, contributes to the cross section, if the photon beams are polarized and if we observe the helicity of the top quarks. It is demonstrated in the framework of the minimal supersymmetric extension of the standard model that the H and A contributions can be sizable at future #gamma##gamma# colliders for small values of tan #beta#. The methods to measure the CP-parity of the Higgs boson are also presented. The statistical significance of detecting the Higgs signals and measuring the Higgs CP-parity is evaluated. (orig.)

2000-05-01

331

Optimization of products and processes in petrochemical industry through modifications in the existing agitation systems: Case studies; Otimizacao de processos/produtos da industria petroquimica atraves de modificacoes nos sistemas de agitacao existentes. Estudo de casos  

Energy Technology Data Exchange (ETDEWEB)

Nowadays, mixing is one of the most powerful tools for the process and products optimization in chemical process industries. The available technology can help in achieving almost any desired outcomes related to the process-side of the systems. This paper presents a practical methodology to improve existing agitation systems in order to overcome the constraints previously identified in the process. Well succeed real cases using this methodology in a petrochemical plant (Nitriflex S.A.) are presented. (author) 13 refs., 1 figs., 2 tabs.

1992-12-31

332

Hydrogen production in a 5 kW Diesel Oxidative Steam Reformer  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a reformer prototype for the production of the necessary H{sub 2} to supply a 5 kW PEMFC and its first results. The fuel processor consists of an OSR and a WGS and a PROX reactors. The design of the system was carried out with a one-dimensional model. The mixture chamber was specially studied with a CFD code (Fluent), taking into account the effect of fuel evaporation and the cool flame process. The aim of the designed facility is to be able of characterising each component and controlling each working parameter. Eventually, using diesel as fuel, results from the mixture chamber, OSR, WGS and PROX reactors are presented. It also includes conclusions and future works. (authors)

2006-07-01

333

Computer Aided Optimization of the Unconventional Processing  

CERN Document Server

The unconventional technologies, currently applied at a certain category of materials, difficult to be processed through usual techniques, have undergone during the last 60 years all the stages, since their discovery to their use on a large scale. They are based on elementary mechanisms which run the processing through classic methods, yet, they use in addition the interconnections of these methods. This leads to a plus in performance by increasing the outcomes precision, reducing the processing time, increasing the quality of the finite product, etc. This performance can be much increased by using the computer and a software product in assisting the human operator in the processing by an unconventional method such as; the electric or electro-chemical erosion, the complex electric-electro-chemical erosion, the processing by a laser fascicle and so on. The present work presents such an application based ...

2009-01-01

334

Bonding of the Inner Tracker Silicon Microstrip Modules  

CERN Document Server

Microbonding of the CMS Tracker Inner Barrel (TIB) and Tracker Inner Disks (TID) modules was shared among six different Italian Institutes. The organization devised and the infrastructure deployed to handle this task is illustrated. Microbonding specifications and procedures for the different types of TIB and TID modules are given. The tooling specially designed and developed for these types of modules is described. Experience of production is presented. Attained production rates are given. An analysis of the microbonding quality achieved is presented, based on bond strengths measured in sample bond pull tests as well as on rates of bonding failures. Italian Bonding Centers routinely performed well above minimum specifications and a very low global introduced failure rate, at the strip level, of only $\\sim$0.015 \\% is observed.

2008-01-01

335

Cyclotron Production of Radioisotopes  

International Science & Technology Center (ISTC)

Production of Radioactive Isotopes in Republic of Kasakhstan.

336

Fate of corrosion products released from stainless steel in marine sediments and seawater. Part 3. Calcareous ooze  

International Nuclear Information System (INIS)

The physicochemical forms and partitioning of corrosion products released from stainless steel upon exposure to selected environmental conditions is the subject of this investigation. This report describes the influence of calcareous sediment on the rate of release and fate of corrosion products produced when neutron-activated stainless steel specimens were exposed to a Globigerina ooze taken from the Northeast Pacific Ocean. The calcareous ooze used in this study consists largely of planktonic formanifera tests and was found to be about 90% CaCO_3. The trace metal content of this sediment was typical of average deep-sea carbonate sediments, and the ratios of trace elements to Ti were not remarkably different from a coastal clayey silt or a Northeast Pacific pelagic red clay. Most (>80%) of the trace metals extracted by sequential chemical treatment were associated with reductant-soluble materials, i.e., amorphous Mn and Fe oxides, or were ...

337

Corrosion product role on the inhibition of Zn alloy electrodeposit corrosion  

Energy Technology Data Exchange (ETDEWEB)

Electrodeposited Zn alloys with Fe group metals are known to be more resistant than pure Zn. However, the role of the corrosion products on the corrosion inhibition is not considered up to date. The aim of the present work was to examine the composition of corrosion products, which form on the Zn and Zn alloy surfaces under atmospheric corrosion conditions up to 3 year of exposure, trying to correlate it with the differences in their corrosion resistance. Zn corrosion products have been characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Corrosion film composition was determined to depend on the sample exposure she, as well on the coating type. During the initial exposure stages oxide film was found to be the principal reaction product (XPS data), which in marine station consists from hydroxide phase exceptionally, while in urban one, contain up to ...

1998-12-31

338

Spectrophotometric determination of vanadium(V) with 2-carbethoxy-5-hydroxy-1-(4-tolyl)-4-pyridone  

International Nuclear Information System (INIS)

Vanadium(V) in aqueous HCl, HNO_3 or H_2SO_4 solutions is extracted with 2-carbethoxy-5-hydroxy-1-(4-tolyl)-4-pyridone (HA) dissolved in CHCl_3 and determined spectrophotometrically, Depending on the composition of the aqueous phase, two complexes are formed. At pH 1 (HCl, HNO_3, H_2SO_4) VO_2A(HA)_2 is formed with maximal absorption at 478 nm. However, from 4-5 M HCl, VO_2Cl(HA)_3 is extracted, and has maximal absorption at 615 nm. The same complex is extracted from 2-3 M HNO_3 or 3-4 M H_2SO_4 if enough chloride is added. Solutions of both complexes follow Beer's law and the molar extinction coefficients are 4.15x10"3 1.mole"-"1cm"-"1 at 478 nm and 5.10x10"3 at 615 nm. The determination of vanadium at both wavelengths is very simple, fast and selective. The composition of the complexes was established by the usual methods as well as by characterization of the ...

1975-01-01

339

Orion's Bar: Physical Conditions across the Definitive H+ / H0 / H2 Interface  

CERN Document Server

Previous work has shown the Orion Bar to be an interface between ionized and molecular gas, viewed roughly edge on, which is excited by the light from the Trapezium cluster. Much of the emission from any star-forming region will originate from such interfaces, so the Bar serves as a foundation test of any emission model. Here we combine X-ray, optical, IR and radio data sets to derive emission spectra along the transition from H+ to H0 to H2 regions. We then reproduce the spectra of these layers with a simulation that simultaneously accounts for the detailed microphysics of the gas, the grains, and molecules, especially H2 and CO. The magnetic field, observed to be the dominant pressure in another region of the Orion Nebula, is treated as a free parameter, along with the density of cosmic rays. Our model successfully accounts for the optical, IR and radio observations across the Bar by including a ...

2008-01-01

340

Hydrogen evolution reaction on single crystal WO3/C nanoparticles supported on carbon in acid and alkaline solution  

British Library Electronic Table of Contents (United Kingdom)

Single crystal tungsten oxide (WO3) nanoparticles were prepared via a microwave-assisted method. Electrochemical activity for hydrogen evolution reaction (HER) on WO3 supported on carbon black (WO3/C) electrocatalyst was first studied in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH) at room temperature. The overall experimental results revealed that the electrocatalytic activity for HER on WO3/C is one order magnitude higher than those obtained with carbon black in 0.5 M H2SO4 and is six times than in the case of carbon black in 1.0 M KOH. These results demonstrated that WO3 could enhance the electrocatalytic activity for hydrogen evolution reaction in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH). On the other hand, the kinetic reaction mechanisms were disc...

2011-01-01

341

Electron momentum spectroscopy of H_2 and D_2: Ionization to ground and excited final states  

International Nuclear Information System (INIS)

The symmetric noncoplanar (e,2e) cross sections (momentum profiles) of H_2 and D_2 for the transitions to the 2p#sigma#_u and 2s#sigma#_g excited ion states have been measured, relative to the ground-state ion transition, using a high-sensitivity multichannel momentum-dispersive electron momentum spectrometer (EMS) at an impact energy of 1200 eV. Newly calculated plane-wave impulse approximation (PWIA) cross sections, based on a full-configuration-interaction H_2 wave function, are compared to the experimental results. These calculations are in better agreement with the experimental results for the transition to the 2s#sigma#_g ion state than the earlier theoretical work of Liu and Smith, Jr. [Phys. Rev. A 31, 3003 (1985)] which has been found to be in error. Nevertheless, significant discrepancies between the relative experimental and theoretical cross sections are observed for the transitions to ...

342

Cosmic evolution of the atomic and molecular gas content of galaxies  

CERN Document Server

We study the evolution of the cold gas content of galaxies by splitting the interstellar medium into its atomic and molecular hydrogen components, using the galaxy formation model GALFORM in the LCDM framework. We calculate the molecular-to-atomic hydrogen mass ratio, H2/HI, in each galaxy using two different approaches; the pressure-based empirical relation of Blitz & Rosolowsky and the theoretical model of Krumholz, McKeee & Tumlinson, and apply them to consistently calculate the star formation rates of galaxies. We find that the model based on the Blitz & Rosolowsky law predicts an HI mass function, CO(1-0) luminosity function, correlations between the H2/HI ratio and stellar and cold gas mass, and infrared-CO luminosity relation in good agreement with local and high redshift observations. The HI mass function evolves weakly with redshift, with the number density of high mass galaxies ...

2011-01-01

343

Characterization and reactivity of Fe3O4/FeMnOx core/shell nanoparticles for methylene blue discoloration with H2O2  

British Library Electronic Table of Contents (United Kingdom)

A magnetic core/shell Fe3O4/FeMnOx catalyst was prepared by a simple oxidation-precipitation method. The catalyst was characterized by X-ray diffraction, transmission electron microscope, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and cyclic voltammetry. The characterization studies verified that Fe3O4 core was coated with a layer of Fe-Mn oxide. The Fe3O4/FeMnOx was found to be an effective and stable heterogeneous catalyst for the discoloration of methylene blue (MB) in aqueous solution by H2O2. The high catalytic activity is due to the FeMnOx shell, which not only increased the surface hydroxyl groups, but also enhanced the interfacial electron transfer. The discoloration of MB could be due to the decomposition of H2O2 into ?OH ...

2011-01-01

344

Biological Research for Radiation Protection  

International Nuclear Information System (INIS)

The work scope of 'Biological Research for the Radiation Protection' had contained the research about ornithine decarboxylase and its controlling proteins, thioredoxin, peroxiredoxin, S-adenosymethionine decarboxylase, and glutamate decarboxylase 67KD effect on the cell death triggered ionizing radiation and H_2O_2(toxic agents). In this study, to elucidate the role of these proteins in the ionizing radiation (or H_2O_2)-induced apoptotic cell death, we utilized sensesed (or antisensed) cells, which overexpress (or down-regulate) RNAs associated with these proteins biosynthesis, and investigated the effects of these genes on the cytotoxicity caused by ionizing radiation and H_2O_2(or paraquat). We also investigated whether genisteine(or thiamine) may enhance the cytotoxic efficacy of tumor cells caused by ionizing radiation (may enhance the preventing effect ...

345

Anodic Protection performance of Steels ASTM A 516-60 And JIS G 3131 SPHC In Concentrated Sulfuric Acid  

International Nuclear Information System (INIS)

One of the methods to protect a carbon steel material from corrosion attack of sulfuric acid environment is with anodic protection. This research was intended to investigate the effect of anodic protection quickened with potential polarization, The material under investigation were ASTM A 516 and JIS G 3131-SPHC in highly concentrated H_2SO_4 solution. The results showed that potential that was effective for anodic protection in ASTM A 516-60 were at 236-436 mV for 75%, 276-476 mV for 80%, 264-514 mV for 85%,285-485 mV for 90%, and 231-431 mV for 97% H_2SO_4 so that in JlS G 3131-SPHC were at 303 -503 mV for 75%, 290-490 mV for 80%, 269- 516 mV for 85%, 264-514 mV for 90%, and 287 -487 mV for 97% H_2SO_4.

2001-06-01

346

Washington: a guide to geothermal energy development  

Energy Technology Data Exchange (ETDEWEB)

A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined. (MHR)

1980-01-01

347

The solar energy in Lebanon: an inexhaustible and economical energy  

International Nuclear Information System (INIS)

The article describes the energy in Lebanon. In 1995, 97% of the imported energy was based on hydrocarbons. Fuel and gas oil present 66% of the final energy. Air pollution is mainly caused by the transportation sector (vehicles and buses...) which presents 70% of the global atmospheric pollution. Renewable energy such as biomass, fossil energy, hydro-energy, solar energy... are also described. The solar energy was defined as a best solution that preserve health in Lebanon. The different applications of the solar for energy production is discussed: photovoltaic , thermal heating, sanitary hot water, electrical heaters, solar water heaters...In conclusion, solar heaters economize 80% of the annual energy expenses

1997-06-01

348

The effect of the shear rate-dependent thermal conductivity of non-Newtonian fluids on the heat transfer in a pipe flow  

Science.gov (United States)

The present study investigates the effect of the shear rate-dependent thermal conductivity of non-Newtonian fluids on the heat transfer enhancement in a pipe flow. The constant heat flux as thermal boundary condition was adopted in the thermally developed region. The present analytical results show the heat transfer enhancement over those of a shear rate-independent thermal conductivity fluid. The heat transfer coefficient ratio (h/h{sub 0}) linearly increase with the non-dimensional average velocity difference which is the product of the shear rate-dependence of the thermal conductivity and wall-shear rate.

1996-09-01

349

Novel regenerable sorbent for SO/sub 2/. [Red mud (iron oxide)  

Energy Technology Data Exchange (ETDEWEB)

A detailed study was undertaken to examine the potential of iron oxide present in red mud (a waste product from Bayer's alumina process) as a sorbent for SO/sub 2/ capture by dry process. The other constituents present in the red mud can bring about enhanced utilization of the active component provided they are almost completely inert. The practical use of the process has been explored and a few batchwise cyclic operations of SO/sub 2/ capture and regeneration have also been carried out. A kinetic model of the reaction has been proposed.

1988-01-01

350

Neon-20 depth-dose relations in water  

Energy Technology Data Exchange (ETDEWEB)

The dose from heavy ion beams has been calculated using a one-dimensional transport theory and evaluated for 670 MeV/amu /sup 20/Ne beams in water. The result is presented so as to be applicable to arbitrary ions for which the necessary interaction data are known. The present evaluation is based on the Silberberg-Tsao fragmentation parameters augmented with light fragment production from intranuclear cascades, recently calculated nuclear absorption cross sections, and evaluated stopping power data. Comparison with recent experimental data obtained at the Lawrence Berkeley Laboratory reveals the need for more accurate fragmentation data.

1984-05-01

351

Information compendium of the Mexican Energy Sector  

International Nuclear Information System (INIS)

This is the first report about a relevant and compiled information on the Mexican Energy Sector. It was realized in one volume by the University Energy Program of the National Autonomous University of Mexico and it comprises information for the period 1996-1997. In the chapter 1 there are presented the numbers of hydrocarbon reserves. Chapter 2 treats about production, events and its results. Likewise chapter 3 shows information about the typical Installations for petroleum, gas and electricity including through of the nuclear energy. In the chapter 4, named Energy Consumption, is presented a National energy balance for 1996 and, finally there are a sections about the prices, the rates and a glossary to facilitate its understanding. (Author)

352

Inborn Errors of Metabolism Presenting in Childhood  

British Library Electronic Table of Contents (United Kingdom)

Abstract Neurodegenerative and neurometabolic disorders may cause significant morbidity and mortality in children. Imaging is important in early diagnosis of metabolic disorders and in determining the extent of brain injury. Especially after the development of new techniques such as diffusion-weighted magnetic resonance imaging (MRI) and magnetic resonance spectroscopy (MRS), neuroimaging plays more important role in the diagnosis and management of these disorders. In these disorders, usually a mutation causes a clinically significant block in one or more metabolic pathways. This blockage usually results in either a deficiency of the product or in an accumulation of substrate with damage induced by either storage or toxicity. The presenting symptoms are usually nonspecific. In some of the ...

2011-01-01

353

Energy balances of OECD countries 1970/1982  

Energy Technology Data Exchange (ETDEWEB)

The present volume provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD Countries. It covers the years 1970 to 1982 year by year and includes many revisions and additions to data previously published. The balances in the present volume are based on data published in OECD Energy Statistics 1971-1981 and OECD Energy Statistics 1981-1982. Tables for each OECD Country include production, import, export, consumption by the different industries, transportation, agriculture, residential sector of the different energies: solid fuels, petroleum, gas, nuclear power and hydroelectricity.

1984-01-01

354

Design, performance, and economics of 50-kW and 500-kW vertical axis wind turbines  

Science.gov (United States)

A review of the development and performance of the DAF Indal 50-kW vertical axis Darrieus wind turbine shows that a high level of technical development and reliability has been achieved. Features of the drive train, braking and control systems are discussed and performance details are presented. Details are also presented of a 500-kW VAWT that is currently in production. A discussion of the economics of both the 50-kW and 500-kW VAWTs is included, showing the effects of charge rate, installed cost, operating cost, performance, and efficiency. 6 references.

1983-11-01

355

Alaska: a guide to geothermal energy development  

Energy Technology Data Exchange (ETDEWEB)

A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined. (MHR)

1980-06-01

356

Technical development of double-clad process for thin strip casting of carbon steel  

Energy Technology Data Exchange (ETDEWEB)

This report documents the technical development for a patent disclosure of a double-clad process for the continuous casting of thin-strip carbon steel. The fundamental idea of the disclosure is to form a product strip by depositing molten steel between two, cooled, clad strips of the same material. The claimed benefits include: (a) the conservation of energy in steel making through the elimination of soaking pits and reheat cycles, and (b) an improved surface on both sides of the as-cast product such that it will be suitable for direct feed to a cold-reduction mill. However, the process as conceived is not necessarily limited to the casting of carbon steel, but may be also applied to other metals and alloys. The work is described under three headings as follows. Preliminary Considerations and Scoping Analysis presents the basic idea of the double-clad, thin-strip casting process; the energy conservation potential; scoping ...

1984-08-01

357

Evaluation of the hemodynamics of the femoral head compared with the ilium, femoral neck and femoral intertrochanteric region in healthy adults. Measurement with positron emission tomography (PET)  

International Nuclear Information System (INIS)

Non-traumatic osteonecrosis of the femoral head (ONF) is considered to be a disease that occurs primarily due to ischemia of the femoral head, while its etiology and pathology are not fully understood. It is therefore necessary to identify the characteristics of the hemodynamics of the femoral head. In this study, the hemodynamics in the ilium and proximal regions of the femur, including the femoral head, was investigated using positron emission tomography (PET). The subjects of this study consisted of 8 hip joints of four healthy male adults and 3 hip joints on the contralateral side of a femoral neck fracture, avulsion fracture of the greater trochanter and coxarthrosis (1 case each, all females) for a total of 11 hip joints of 7 subjects. The ages of the subjects ranged from 25 to 87 years (average age: 54 years). Blood flow was measured by means of the H_2"1"5O dynamic study method and blood volume was measured by means of the "1"5O-labeled ...

2005-10-01

358

The importance of an accurate target wave function in variational calculations for (e^{+}-H_{2}) scattering  

CERN Document Server

Using the complex Kohn method, we have calculated variational values of phase shifts and the annihilation parameter, Z_{eff}, for the elastic scattering of positrons by molecular hydrogen. Our results are sensitive to small changes in the accuracy of the wave function representing the target hydrogen molecule. We have developed a systematic approach to demonstrate that, at low positron energies, there are particular forms of the Kohn trial wave function for which the results of variational calculations are not reliable, even when the target wave function accounts for as much as 96.8% of the correlation energy of H_{2}. We find that reliable results can be recovered if our calculations are extended to admit more sophisticated target wave functions accounting for 99.7% of the correlation energy. Remaining discrepancies between theory and experiment are briefly discussed.

2008-01-01

359

Synergistic effect of iodide ion and polyacrylic acid on corrosion inhibition of iron in H2SO4 investigated by electrochemical techniques  

British Library Electronic Table of Contents (United Kingdom)

Corrosion inhibition of iron in H2SO4 by polyacrylic acid (PAA) was investigated using electrochemical techniques at 30degreeC. Results obtained indicate that PAA inhibited the corrosion of iron in the acid medium. Inhibition efficiency increases with increase in PAA concentration and synergistically enhanced on addition of iodide ions. Potentiodynamic polarization results suggest that PAA functions as a modest cathodic inhibitor. The adsorption of PAA onto the iron surface followed Temkin adsorption isotherm. FTIR analysis revealed that the synergistic effect due to co-adsorption of iodide ions and PAA is co-operative in nature.

2010-01-01

360

RHEED, AES and XPS studies of the passive films formed on ion implanted stainless steel  

International Nuclear Information System (INIS)

P-implantation (10"1"7 ions cm"-"2, 40 KeV) into 304 stainless steel (ss) has been carried out, and an amorphous surface alloy was formed. Polarization studies in deaerated 1N H_2SO_4+ 2% NaCl showed that P-implantation improved both the general and localized corrosion resistance of 304 ss. A comparative study has been carried out between the implanted and unimplanted steel to determine what influence P-implantation has upon the properties of the passive film formed 1N H_2SO_4. The influence of Cl ions on pre-formed passive films was also studied. RHEED, XPS and AES were used to evaluate the nature of the passive films formed in these studies.

2005-05-26

361

Preparation of tetravalent praseodymium in potassium phosphotungstate aqueous solutions  

International Nuclear Information System (INIS)

The possibility has been studied of oxidizing Prsup((3)) to Prsup((4)) when Prsup((3)) is added to an aqueous weakly-acid solution containing K_1_0[P_2W_1_7O_6_1H_2O] x H_2O. A sharp change in the solution colouring has been observed as a result of Prsup((3)) oxidation to Prsup((4)). The absorption spectra of solution of Prsup((4)) have been recorded and the values of the molar extinction coefficients have been determined. On storage of the solution, Prsup((4))reduces to Prsup((3)) with a half-reduction period of 0.2-0.5 hour.

1977-01-01

362

Light emission from hydrogen-copper interaction at grazing incidence  

International Nuclear Information System (INIS)

The optical emission of excited H reflected from clean Cu(110) after impingement of H"+ and H_2"+ in the energy range of 250 eV to 20 keV per nucleon at 70"0 angle of incidence to the surface normal was measured. For incident 10 keV H_2"+, the highest excited hydrogen state detected was the n=10 level. The Hsub(#alpha#) yield was found to be fluence and energy dependent. This effect is attributed either to fast sputtered hydrogen, surface roughness or to an increase with hydrogen concentration in electron states of p-like symmetry near the Fermi level of copper. The Hsub(#alpha#) yield per reflected nucleon shows approximately an exponential dependence on both projectile energy per nucleon and scattered particle reciprocal velocity perpendicular to the surface. (orig.).

1983-07-01

363

Electron binding to isolated polar molecules and molecular dipole assemblies  

International Nuclear Information System (INIS)

In a sufficiently large cluster of several polar molecules, collective interactions lead to localization or 'solvation' of electrons. The existence of the solvated electron is known since 1863 in liquid ammonia and since 1962 for liquid water. In 1984, electron localization in clusters was experimentally demonstrated in (H_2O)_N_#>=#_1_1 and (NH_3)_N_#>=#_3_4 clusters. In cooperation with K. Bowen, we recently initiated a test of the theory of electron binding by a dipole and a new ground state dipole bound dimer anion, (H_2O..NH_3), was predicted and observed. We here describe results of a search for new dipole-bound and solvated electron systems. (author).

1994-03-20

364

Crystal structure of the human centromeric nucleosome containing CENP-A  

British Library Electronic Table of Contents (United Kingdom)

In eukaryotes, accurate chromosome segregation during mitosis and meiosis is coordinated by kinetochores, which are unique chromosomal sites for microtubule attachment. Centromeres specify the kinetochore formation sites on individual chromosomes, and are epigenetically marked by the assembly of nucleosomes containing the centromere-specific histone H3 variant, CENP-A. Although the underlying mechanism is unclear, centromere inheritance is probably dictated by the architecture of the centromeric nucleosome. Here we report the crystal structure of the human centromeric nucleosome containing CENP-A and its cognate ?-satellite DNA derivative (147 base pairs). In the human CENP-A nucleosome, the DNA is wrapped around the histone octamer, consisting of two each of histones H2A, H2B, H4 and CENP...

2011-01-01

365

Biosorption of reactive dye by waste biomass of Nostoc linckia  

British Library Electronic Table of Contents (United Kingdom)

Potential of spent biomass of a cyanobacterium, Nostoc linckia HA 46, from a hydrogen bioreactor was studied for biosorption of a textile dye, reactive red 198. The waste biomass was immobilized in calcium alginate and used for biosorption of the dye from aqueous solution using response surface methodology (RSM). Kinetics of the dye in aqueous solution was studied in batch mode. Interactive effects of initial dye concentration (100-500mg/L), pH (2-6) and temperature (25-45^oC) on dye removal were examined using Box-Behnken design. Maximum adsorption capacity of the immobilized biomass was 93.5mg/g at pH 2.0, initial concentration of 100mg/L and 35^oC temperature, when 94% of the dye was removed. Fourier transform infrared (FT-IR) studies revealed that biosorption was mainly mediated by fun...

2011-01-01

366

Assembly of a water-insoluble strontium metal-organic framework with luminescent properties  

British Library Electronic Table of Contents (United Kingdom)

A new strontium metal-organic framework, [Sr2(BTEC)(H2O)4] 2H2O (1) (H4BTEC=benzene-1,2,4,5-tetracarboxylic acid), has been successfully synthesized by mixing the starting reagents. The single-crystal structure analysis showed that compound 1 displayed three-dimensional structures containing inorganic motifs with two-dimensional layers pillar-connected through organic linkers and forming water-coordinated neutral framework. Further studies revealed that compound 1 was insoluble in water and that it emitted strong luminescence at approximately 437nm after dehydration.

2011-01-01

367

Analysis of plasma treatment and vapor heat treatment for thin-film transistors by extracting trap densities at front and back interfaces  

International Nuclear Information System (INIS)

Hydrogen (H) plasma treatment, oxygen (O) plasma treatment and water (H_2O)-vapor heat treatment for polycrystalline-silicon (poly-Si) thin-film transistors (TFTs) have been analyzed by separately extracting trap density at a front silicon-oxide interface (D_F) and trap density at a back interface (D_B). It is found that the H plasma treatment is apt to generate D_F and D_B. The O plasma treatment reduces D_F, while the H_2O-vapor heat treatment reduces both D_F and D_B. Improvement of transistor characteristics of poly-Si TFTs depends on understanding these results.

2004-05-17

368

AFM Imaging of SWI/SNF action: mapping the nucleosome remodeling and sliding  

CERN Document Server

We propose a combined experimental (Atomic Force Microscopy) and theoretical study of the structural and dynamical properties of nucleosomes. In contrast to biochemical approaches, this method allows to determine simultaneously the DNA complexed length distribution and nucleosome position in various contexts. First, we show that differences in the nucleo-proteic structure observed between conventional H2A and H2A.Bbd variant nucleosomes induce quantitative changes in the in the length distribution of DNA complexed with histones. Then, the sliding action of remodeling complex SWI/SNF is characterized through the evolution of the nucleosome position and wrapped DNA length mapping. Using a linear energetic model for the distribution of DNA complexed length, we extract the net wrapping energy of DNA onto the histone octamer, and compare it to previous studies.

2007-01-01

369

A study on rf plasma nitriding at a constant power in different H_2-N_2 mixtures at different temperatures  

International Nuclear Information System (INIS)

Austenitic stainless steel AISI 304 has been nitrided by radio frequency (rf) plasma containing various nitrogen-hydrogen gas mixtures, in order to study the effect of hydrogen on structure and magnetic properties of the formed compound layer. The thermal temperature has been measured at the vicinity of the samples. The compound layer thus produced has been characterized using, X-ray diffractometer and vibration sample magnetometer. Providing the total pressure of nitrogen and hydrogen is held constant, the addition of hydrogen up to 50% gives new structural phases. The magnetization values of the plasma treated samples are strongly dependent on the percentage of H_2 in the gas phase. An excessive amount of hydrogen (#approx#75%) on the other hand, retards the nitriding process. The surface temperature of the sample and plasma condition is crucial factors for nitriding process.

2006-04-15

370

A Combinatorial Library of Micro-Topographies and Chemical Compositions for Tailored Surface Wettability  

British Library Electronic Table of Contents (United Kingdom)

Abstract Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X-=-1-m and...

2011-01-01

371

Theoretical and scaling factors methods to calculate the radioactivity in operational waste streams from Unit 1 at Cernavoda NPP  

International Nuclear Information System (INIS)

The main goal of this paper is to present a methodology for calculating the radioactivity in the moderator and heat transport systems of Cernavoda NPP Unit 1, with the intention to improve the knowledge on the radionuclides inventories in the operational waste streams, and to aid the licensing process of new near surface repository. In the present paper we describe our methodology for estimating H-3 and C-14 production rates in the heavy-water moderator and heat transport systems using the capacity factors from 1997 to 2007 years. The radioactivity of the difficult-to-measure nuclides is predicted by scaling method using measured concentration in reference CANDU 6 reactor Gentilly-2. The difficult-to-measure radionuclides of primary interest in this study were those with long half-lives which have a significant role for post-closure safety assessment. The equation used to scale fission products (parents ...

2009-05-27

372

Solar desalination using humidification-dehumidification processes. Part II. An experimental investigation  

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation of a humidification-dehumidification desalination (HDD) process using solar energy at the weather conditions of Suez City, Egypt, is presented. A test rig is designed and constructed to conduct this investigation under different environmental and operating conditions. The test rig consists of a solar water heater (concentrator solar collector type), solar air heater (flat plate solar collector type), humidifier tower and dehumidifier exchanger. Different variables are examined including the feed water flow rate, the air flow rate, the cooling water flow rate in the dehumidifier and the weather conditions. Comparisons between the experimental results and other published results are presented. It is found that the results of the developed mathematical model by the same authors are in good agreement with the experimental results. The tested results show that the productivity of the system is ...

2004-05-01

373

Solar desalination using humidification-dehumidification processes. Part II. An experimental investigation  

International Nuclear Information System (INIS)

An experimental investigation of a humidification-dehumidification desalination (HDD) process using solar energy at the weather conditions of Suez City, Egypt, is presented. A test rig is designed and constructed to conduct this investigation under different environmental and operating conditions. The test rig consists of a solar water heater (concentrator solar collector type), solar air heater (flat plate solar collector type), humidifier tower and dehumidifier exchanger. Different variables are examined including the feed water flow rate, the air flow rate, the cooling water flow rate in the dehumidifier and the weather conditions. Comparisons between the experimental results and other published results are presented. It is found that the results of the developed mathematical model by the same authors are in good agreement with the experimental results. The tested results show that the productivity of the system is ...

2004-05-01

374

Solar desalination using humidification dehumidification processes. Pt. 2. An experimental investigation  

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation of a humidification-dehumidification desalination (HDD) process using solar energy at the weather conditions of Suez City, Egypt, is presented. A test rig is designed and constructed to conduct this investigation under different environmental and operating conditions. The test rig consists of a solar water heater (concentrator solar collector type), solar air heater (flat plate solar collector type), humidifier tower and dehumidifier exchanger. Different variables are examined including the feed water flow rate, the air flow rate, the cooling water flow rate in the dehumidifier and the weather conditions. Comparisons between the experimental results and other published results are presented. It is found that the results of the developed mathematical model by the same authors are in good agreement with the experimental results. The tested results show that the productivity of the system is ...

2004-05-01

375

Plutonium Finishing Plant safety evaluation report  

Energy Technology Data Exchange (ETDEWEB)

The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE`s independent ...

1995-01-01

376

Emissions from power plants 1987-1996; Emissioner fra kraftvaerkerne 1987-1996  

Energy Technology Data Exchange (ETDEWEB)

The document gives statistics on the pollutive emissions from Danish power plants during the period 1987-1996, the main pollutants being sulphur dioxide, nitrogen oxides and carbon dioxide. Data on efficiency levels relative to the production of electricity and heating and on the power plants` contribution to the total emission of CO{sub 2}, NO{sub x}, and SO{sub 2} from energy consumption in Denmark, are presented, and also as corrected for the net import of electricity. Other data on the emission of each of these chemicals by power plants are presented as factual, and corrected in accordance with the net import of electricity, and as factual per consumed and produced energy unit at the power plants. Short notes on related Danish legislation are found in addition to information on sources, methods and definitions used as a basis for the production of this document. Emission from power stations is ...

1997-08-01

377

A novel method for solving lithium carbonate pellet by binary-acid for tritium production rate measurement by liquid scintillation counting technique  

International Nuclear Information System (INIS)

Lithium carbonate pellets are frequently used for estimation of tritium production rate in irradiated samples in fusion blanket neutronics experiment and the activity is measured by liquid scintillation counting technique. In this measurement, it is essential to solve the lithium carbonate pellet as much as possible and to mix the pellet solution into scintillation cocktail homogeneously at stable condition. For this purpose, a novel binary-acid method has been developed to solve lithium carbonate and to mix the pellet solution into scintillation cocktail. High solubility is attained by adopting two acids, HNO_3 and CH_3COOH, and a good compatibility of the pellet solution with scintillator is obtained by emulsion cocktail resulting in high counting efficiency. Defining a product of dissolved mass and counting efficiency as a Figure of Merit (FOM), the present method has higher FOM value than the conventional method and is ...

378

Why the negative corona current in air decreases?  

International Nuclear Information System (INIS)

The time dependence of negative corona current I, called by Gagarin like 'relaxing of CV-characteristics', is a observed phenomena. The observed phenomena was explained by two theoretical models considering the ion-molecule and chemical reactions in the negative corona discharges in air, especially the ozone production. In the presented paper the discrepancies of above mentioned models, re-examination the earlier experimental data and presumptions used in models in a light the latest experimentally confirmed facts are discussed.

1996-08-01

379

Virtual Compton Scattering: Results from Jefferson Lab  

Energy Technology Data Exchange (ETDEWEB)

Virtual Compton Scattering o013 the proton has been studied at Q 2 -values of 1:0 and 1:9 (GeV=c) 2 in Hall A at the Thomas Je013erson National Accelerator Facility (JLab). Data were taken below and above the pion production threshold as well as in the resonance region. Results obtained below pion threshold at Q 2 = 1:0 (GeV=c) 2 are presented in this paper.

2003-05-01

380

Top pair production in e+e- and {gamma}{gamma} processes  

Energy Technology Data Exchange (ETDEWEB)

We analyze spin correlations between top quark and anti-top quark produced at polarized e{sup +} e{sup -} and {gamma}{gamma} colliders. We consider a generic spin basis to find a strong spin correlation. Optimal spin decompositions for top quark pair are presented for e{sup +}e{sup -} and {gamma}{gamma} colliders. We show the cross- section in these bases and discuss the characteristics of results.

1998-02-01

381

Thermal reactor safety  

International Nuclear Information System (INIS)

Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.

1990-09-01

382

Thermal reactor safety  

Energy Technology Data Exchange (ETDEWEB)

Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.

1980-06-01

383

The production and destruction of negative ions  

Energy Technology Data Exchange (ETDEWEB)

During the present grant period we have continued our study of the photodetachment of atomic negative ions using cross-beam photoelectron detachment spectroscopy. The experimental technique involves the measurement of, under conditions of good energy and angular resolution, kinetic energies, yields and angular distributions of photoelectrons ejected from the interaction region between perpendicularly crossed laser and negative ion beams. 6 figs.

1990-01-01

384

The physics of Electron Beam Ion Sources  

Energy Technology Data Exchange (ETDEWEB)

There are 13 Electron Beam Ion Sources in operation which produce highly charged ions, up to Th[sup 80+] and Xe[sup 53+]. Most of the sources are used to study these ions under electron impact or when recombining with gaseous or solid targets. That provides an insight into the atomic physics of these highly charged ions and into the physics of the plasma in which such ions can be found. This paper reviews the present knowledge of atomic processes, important in the production of such ions with an EBIS.

1990-01-01

385

The physics of Electron Beam Ion Sources  

Energy Technology Data Exchange (ETDEWEB)

There are 13 Electron Beam Ion Sources in operation which produce highly charged ions, up to Th{sup 80+} and Xe{sup 53+}. Most of the sources are used to study these ions under electron impact or when recombining with gaseous or solid targets. That provides an insight into the atomic physics of these highly charged ions and into the physics of the plasma in which such ions can be found. This paper reviews the present knowledge of atomic processes, important in the production of such ions with an EBIS.

1990-12-31

386

The method and results of measurements of "2"2"2Rn emanation from building materials  

International Nuclear Information System (INIS)

The method and results are presented of measurements of the coefficients of "2"2"2Rn emanation from samples of fly- ashes and slag and other commonly used building materials. A chamber was used for electrostatic collection of "2"2"2Rn decay products. The coefficients of emanation ranged from 0.2% (fly- ashes) to 21.3% (phosphogipsum from phosphorit). (author).

1979-01-01

387

The Silicone Conundrum Part II: ?Low Outgassing? Silicones  

British Library Electronic Table of Contents (United Kingdom)

Silicones have many desirable properties and as a result are incorporated into a wide range of products. However, they present unique problems that result from their propensity to outgas resulting in residue formation at unexpected places. Hence, the silicone conundrum?when to use these materials and when to beware of potential pitfalls. In this article, an outgassing mechanism unique to ?low outgassing? silicones is discussed. Examples are given where this has led to failures and remediation steps are highlighted.

2011-01-01

388

Symplectic Integrators Designed for Simulating Soft Matter  

Science.gov (United States)

Symplectic integrators designed for simulating soft matter at constant temperature and constant pressure (or constant surface tension) are presented. In addition to the well-known merits of symplectic integrators, such as long time stability, these methods allow the estimation of thermal heat production/absorption and thus entropy differences through a simple function of the time scaling factor ?. The relative entropy estimation around crystal-liquid phase transition is given for systems with soft core repulsive potential.

2008-04-01

389

Study on the natural gas utilization in the ceramic industry; Estudo sobre a utilizacao do gas natural na industria ceramica  

Energy Technology Data Exchange (ETDEWEB)

The production, principal applications, characteristics and properties, advantages of the gas natural is showed. A sectorial overview of the ceramic industry and the utilization of the natural gas in the ceramic industry is presented. The expectations are systematized and the impact of the natural gas utilization in the ceramic industry is evaluated. Some conclusions are withdrawn and recommendations suggested.

1998-07-01

390

State of coal gasification for production of fuel gas and synthesis gas  

Energy Technology Data Exchange (ETDEWEB)

The fundamental principles of coal gasification are discussed including the reactions, their course and influencing parameters. Said principles are illustrated considering heat balance as well as process performance. Coal gasification processes are presented which are under development on a pilot plant scale or which are approved on an industrial scale.

1984-04-01

391

Standardization charts for cost-benefit analysis of biogas systems: case study in Jordan  

Energy Technology Data Exchange (ETDEWEB)

This paper establishes a standardization procedure in which results are presented in ready-to-use charts for the economic evaluation of biogas plants. It is hoped this work will alleviate controversial reports on cost-effectiveness of biogas systems. Also, it is found that these systems are the most economic among renewable energy systems using a standardized procedure for their comparison augmented by the generated spider diagrams wherein most probable costing production values for each system are directly compared. (author).

1990-01-01

392

Spectroscopic study of some historical arts  

International Nuclear Information System (INIS)

This work presents the spectroscopic results of the investigations of ancient pottery remains excavated in ancient Kremna (BURDUR-TURKEY). The micro-Raman and FT-IR spectroscopic studies of the pottery remains belonging to sixth century allowed us to identify the mineral composition. Some examples are described of the use of this technique in the field of art conservation and diagnostics, with regard to pigments, and some products of metal alteration.

2009-09-24

393

Slimholes for geothermal reservoir evaluation - An overview  

Energy Technology Data Exchange (ETDEWEB)

The topics covered in this session include: slimhole testing and data acquisition, theoretical and numerical models for slimholes, and an overview of the analysis of slimhole data acquired by the Japanese. The fundamental issues discussed are concerned with assessing the efficacy of slimhole testing for the evaluation of geothermal reservoirs. the term reservoir evaluation is here taken to mean the assessment of the potential of the geothermal reservoir for the profitable production of electrical power. As an introduction to the subsequent presentations and discussions, a brief summary of the more important aspects of the use of slimholes in reservoir evaluation is given.

1996-08-01

394

Simulation of oil and gas production forecasts using smoothing methods  

Energy Technology Data Exchange (ETDEWEB)

A variety of forecasting approaches have been used in the energy area. Forecast simulations provide a common basis for comparing the relative precision of different forecasting methods. This paper presents a forecast simulation made using smoothing procedures for forecasting time series. The simulation design, statistical analysis, and conclusions are provided.

1987-01-01

395

Projected radionuclide inventories of DWPF glass from current waste at time of production  

Energy Technology Data Exchange (ETDEWEB)

The Waste Acceptance Preliminary Specifications (WAPS) require that the DWPF estimate the inventory of long-lived radionuclides present in the waste glass, and report the values in the Waste Form Qualification Report. In this report, conservative (biased high) estimates of the radionuclide inventory of glass produced from waste currently in the Tank Farm are provided. In most cases, these calculated values compare favorably with actual data. In those cases where the agreement is not good, the values reported here are conservative.

1993-02-04

396

Photon final states at the Tevatron  

Energy Technology Data Exchange (ETDEWEB)

The authors present here several recent measurements involving associate production of photons and jets at the Tevatron. In particular, inclusive photon + met from D0, and photon + b-jets and photon + b-jet + leptons + MET from CDF are described in some detail. These measurements offer a good test of QCD predictions in rather complex final states.

2008-04-01

397

Optimization of low pressure silicon nitride film growth from dichlorosilane and ammonia in integrated circuit manufacture  

Energy Technology Data Exchange (ETDEWEB)

An optimization criterion accounting for the energy and material consumption is defined. The allowed limits of the variations in the technological factors are discussed and the optimization criterion values within these limits are calculated. The analysis presented, demonstrating the significance of the chosen factors for the production cost-price, is of great practical importance. (orig.).

1991-08-15

398

Monthly energy review, October 1998  

Energy Technology Data Exchange (ETDEWEB)

The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

1998-10-01

399

Monthly Energy Review  

Energy Technology Data Exchange (ETDEWEB)

This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.

1996-05-28

400

Investigation of GOSIP technology at ANL  

Energy Technology Data Exchange (ETDEWEB)

This document describes testing of OSI products conducted at Argonne National Laboratory. Sun, IBM, and Clsco hardware platforms were used. Various software packages that implement file transfer and gateway applications were evaluated. The OSI model and GOSIP compliance are briefly discussed. Technical details on OSI addressing and routing are presented. The relationship of this testing to other OSI activities at Argonne and to activities of the national networking community is discussed. Mention is also made of the relationship of DECnet Phase V transition issues.

1992-01-01

401

International workshop on 'in vitro' culture of forest tree species. Colloque international sur la culture 'in vitro' des essences forestieres  

Energy Technology Data Exchange (ETDEWEB)

Some 43 papers were presented in 4 sections: Organ and bud culture of tree species (24 papers); Cell suspension and callus culture of tree species (11); Culture of haploid tissue of tree species and production of wood homozygotes (3); and Isolation, culture and somatic fusion of protoplasts as a means of somatic hybridization and genetic engineering (5).

1983-01-01

402

Inflammatory mediators promote production of shed LRP1/CD91, which regulates cell signaling and cytokine expression by macrophages  

UK PubMed Central (United Kingdom)

LRP1 is a type-1 transmembrane receptor that mediates the endocytosis of diverse ligands. LRP1 β-chain proteolysis results in release of sLRP1 that is present in human plasma. In this study,...Full Text Available

2010-10-01

403

Industrialization development of food irradiation in China  

International Nuclear Information System (INIS)

This report introduces present status on food irradiation at home and abroad in detail. It also introduces the scientific research and application in reducing diseases caused by food borne pathogens, quarantine control of import and export products, grain store and killing insects in traditional Chinese medicine. The report also analyzes the problems in developing food irradiation in China and gives some suggestions

2004-04-01

404

Industrial waste management information for 1990 and record-to-date  

Energy Technology Data Exchange (ETDEWEB)

This product provides detailed data and graphics on airborne and liquid effluent releases, fuel oil consumption, and water usage for the calendar year 1990. It summarizes industrial waste data records compiled since 1971 for the Idaho National Engineering Laboratory (INEL). The data presented are from the INEL Industrial Waste Management Information System (IWMIS).

1991-08-01

405

Ignition and combustion features of biofuels  

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of experimental investigations of the ignition and combustion of plant biofuels (wood particles, date stones) and products of their mechanical and thermal treatment (pellets, charcoal) at temperatures typical of the burning process in nonforced furnaces and fixed-bed and fluidized-bed gas producers. The influence of the furnace heat treatment of a fuel on its inflammation and combustion has been revealed. The results have been compared with the known data on the burning of pellets, brown coals, and anthracites and with the calculation by the classical diffusion-kinetic model.

2011-01-01

406

Hydrogen uptake and embrittlement of tantalum after electrolytical hydrogen production  

Energy Technology Data Exchange (ETDEWEB)

Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions.

1983-03-01

407

Hydrogen uptake and embrittlement of tantalum after electrolytical hydrogen production  

International Nuclear Information System (INIS)

Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions. (orig.).

408

Future of the Japanese steel industry and a suggestion to the Canadian coal industry  

Energy Technology Data Exchange (ETDEWEB)

Discussion is presented of world crude steel production, the Japanese steel industry and its expectations of the Canadian coal industry. It is concluded that the Canadian coal industry should pay attention to the trend in customer's requirements regarding coal quality, maintain price competitiveness in the international market place, and remain flexible with regard to the market trend.

1989-01-01

409

Fragrance mix II in the baseline series contributes significantly to detection of fragrance allergy  

DEFF Research Database (Denmark)

Fragrance mix II (FM II) is a relatively new screening marker for fragrance contact allergy. It was introduced in the patch test baseline series in Denmark in 2005 and contains six different fragrance chemicals commonly present in cosmetic products and which are known allergens.

2010-01-01

410

Effect of economic indicators and uncertainties on the selection of a production strategy; Analise da influencia de indicadores economicos e incertezas na escolha da estrategia de producao  

Energy Technology Data Exchange (ETDEWEB)

The decision of a firm to make investments on petroleum fields depends on the expected economic performance and on the firm economics context and on country economic and regulatory constraints. Traditionally, the Net Present Value (NPV) has being used for decision criterion as a measure of profitability of investments. The other indicators are used to help investment decision, because, according to the priorities established by the firm, only one indicator may not be sufficient. On this paper we will show production strategies considering a set of economic indicators: NPV, actualized Np, Return on investment (ROI), Equivalent Present Value (EPV), Cost Benefit, and NPV/Np ratio. The use of different economic indicators permits capture different aspects from in a decision process, i.e., each indicator or a set of economic measures may result in a different perspective, that will influence the decision manager. It is important ...

2004-07-01

411

Discrete phase retrieval in musical structures  

British Library Electronic Table of Contents (United Kingdom)

This paper describes phase-retrieval approaches in music by focusing on the particular case of the cyclic groups (beltway problem). After presenting some old and new results on phase retrieval, we introduce the extended phase retrieval for a generalized musical Z-relation. This concept is accompanied by mathematical definitions and motivations from computer-aided composition. We assume from the reader basic knowledge of groups, topological groups, group algebras, group actions, Lebesgue integration, convolution products, and Fourier transform.

2011-01-01

412

Development of a high-output dual-fuel engine  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of a new dual-fuel engine development program. The engine is the largest commercially available in terms of power output (650 hp/cyl) and features very low emissions (1 g/hp-hr NO[sub x]) and excellent fuel consumption (43 percent thermal efficiency). A two-cylinder turbocharged prototype was designed and built for the initial development. Results from testing on 18-cylinder production versions are also reported.

1993-10-01

413

Dai 85 kai kokusu tokubetsukai kenkyu happyo yoshishu (1988). (Proceedings of Special Coke Meeting in (85th). 1988).  

Science.gov (United States)

The invited paper and 11 research papers are included, which were presented at the 85th Special Coke Meeting, Coke Group, Nenryo kyokai opened in Oct., 1988. As the invited paper, ''Production and utilization of blast furnace coke in the future'' is print...

1988-01-01

414

DISPOSAL OF BY-PRODUCTS FROM NONREGENERABLE FLUE GAS DESULFURIZATION SYSTEMS  

Science.gov (United States)

The report gives results of a 4-year study to determine environmentally sound methods for disposing of wastes from nonregenerable flue gas desulfurization (FGD) systems. Data presented incorporates results obtained during the fourth year with material from report EPA-600/7-77-052...

415

CRC handbook of physical properties of rocks. Volume III  

Energy Technology Data Exchange (ETDEWEB)

This book presents topics on: Density of rocks and minerals, includes histograms of density ranges; elastic constants of minerals, elastic moduli, thermal properties; inelastic properties, strength and rheology for rocks and minerals, rock mechanics and friction, and stress-strain relations; radioactivity, decay constants and heat production of isotope systems in geology; seismic attenuation, in rocks, minerals, and the earth, with application to oil exploration and terrestrial studies; and index.

1984-01-01

416

Areva in Niger  

Energy Technology Data Exchange (ETDEWEB)

Niger is the second poorest country in the world but it has natural resources underground in the form of uranium ores deposits. This uranium is currently mined by two companies incorporated under Nigerian law: Somair and Cominak, operated by the principal shareholder Areva (through its subsidiary Cogema). After a presentation of Somair and Cominak key figures, this document details the working conditions and radiological protection, the environmentally friendly operations, the production traceability, the local economic development, the strengthening of the health care system and the development of the infrastructure. (A.L.B.)

2005-02-01

417

Type of brown coal from North-Bohemian basin effect to quality of pyrolysis products  

Energy Technology Data Exchange (ETDEWEB)

By increasing the price of crude oil and natural gas and the decline in their stock a possibility of more intense use of coal reserves as a feedstock not only for energy purposes but also as a feedstock source for other industries, mainly chemical and steel industry, is opening up. At present brown coal exploited in the Czech Republic is explicitly burned in the power sources of various outputs. Coal pyrolysis under the defined conditions may be an outstanding way of non-energetic brown coal processing. The target of our work was to determine the behaviour of various types of brown coal from the North Bohemian Basin under the pyrolysis up to the temperature 750{sup o}C. At the same time, qualitative parameters of the pyrolysis products in dependence on the features of the input brown coal were observed. Various types of brown coal were used for the pyrolysis tests differing mainly in the content of ash, sulphur and tar. Within the work mass ...

2005-07-01

418

The magnetic resonance and its agro-industry applications; a review  

International Nuclear Information System (INIS)

The electromagnetic properties that present hydrogen and other nucleus of agro-alimentary products, have allowed widely use of magnetic resonance (MR) to study the composition and internal structure of these biological materials in a micro and macroscopic scale, in a nondestructive way. In this paper the physical principles, basic equipment to measure the MR signals and the MR imaging of any biological sample, are explained. It is also shown a review of the main agro-alimentary applications, emphasizing in the use of this principle to examine the internal quality of fruits and vegetables. In these products, the MR has been used to detect and follow the evolution of different factors that determine the internal quality after harvesting, during storage and after post harvesting processes. The main studies that have been conducted with MR in harvested products are about physiological disorders that take ...

419

Solar desalination using humidification dehumidification processes. Pt. 1. A numerical investigation  

Energy Technology Data Exchange (ETDEWEB)

A numerical investigation of a humidification dehumidification desalination (HDD) process using solar energy is presented. The HDD system consists mainly of a concentrating solar water heating collector, flat plate solar air heating collector, humidifying tower and dehumidifying exchanger. Two separate circulating loops constitute the HDD system, the first for heating the feed water and the second for heating air. A mathematical model is developed, simulating the HDD system, to study the influence of the different system configurations, weather and operating conditions on the system productivity. The model validity is examined by comparing the theoretical and experimental results of the same authors. It is found that the results of the developed mathematical model are in good agreement with the experimental results and other published works. The results show also that the productivity of the unit is strongly influenced by ...

2004-05-01

420

Solar desalination using humidification dehumidification processes. Part I. A numerical investigation  

Energy Technology Data Exchange (ETDEWEB)

A numerical investigation of a humidification dehumidification desalination (HDD) process using solar energy is presented. The HDD system consists mainly of a concentrating solar water heating collector, flat plate solar air heating collector, humidifying tower and dehumidifying exchanger. Two separate circulating loops constitute the HDD system, the first for heating the feed water and the second for heating air. A mathematical model is developed, simulating the HDD system, to study the influence of the different system configurations, weather and operating conditions on the system productivity. The model validity is examined by comparing the theoretical and experimental results of the same authors. It is found that the results of the developed mathematical model are in good agreement with the experimental results and other published works. The results show also that the productivity of the unit is strongly influenced by ...

2004-05-01

421

Results of radon concentration measurements in some regions of Russia  

Energy Technology Data Exchange (ETDEWEB)

Inhalation of radon and its daughter products makes the major contribution to the total exposure of the population to natural radiations. In implementing a complex ecological survey, concentrations of radon and its daughter products were measured in different regions of Russia, namely, in the St. Petersburg Region, the Central Territories and the Altay Territory. Two suitable low price versions of the dosemeters for measuring environmental radon concentrations based on track-etch and activated-charcoal detectors were used. The radon daughter product activity and the effective dose equivalents were calculated with an equilibrium factor of 0.5 and a recommended effective dose equivalent factor of 0.061 mSv (Bq m{sup -3}){sup -1}. Indoor measurements were taken in more than 1000 dwellings and public and industrial buildings of 21 towns and villages. The track chambers were exposed for about 2-3 months and the charcoal ...

1996-01-01

422

Results of radon concentration measurements in some regions of Russia  

International Nuclear Information System (INIS)

Inhalation of radon and its daughter products makes the major contribution to the total exposure of the population to natural radiations. In implementing a complex ecological survey, concentrations of radon and its daughter products were measured in different regions of Russia, namely, in the St. Petersburg Region, the Central Territories and the Altay Territory. Two suitable low price versions of the dosemeters for measuring environmental radon concentrations based on track-etch and activated-charcoal detectors were used. The radon daughter product activity and the effective dose equivalents were calculated with an equilibrium factor of 0.5 and a recommended effective dose equivalent factor of 0.061 mSv (Bq m"-"3)"-"1. Indoor measurements were taken in more than 1000 dwellings and public and industrial buildings of 21 towns and villages. The track chambers were exposed for about 2-3 months and the charcoal detectors for ...

423

Radiometric analysis of raw materials and end products in the Turkish ceramics industry  

International Nuclear Information System (INIS)

This study presents the findings of radiometric analysis carried out to determine the activity concentrations of natural radionuclides in raw materials (clay, kaolin, quartz, feldspar, dolomite, alumina, bauxite, zirconium minerals, red mud and frit) and end products (glazed ceramic wall and floor tiles) in the Turkish ceramics industry. Hundred forty-six samples were obtained from various manufacturers and suppliers throughout the country and analyzed using gamma-ray spectrometer with HPGe detectors. Radiological parameters such as radium equivalent activity, activity concentration index and alpha index were calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant national and international legislation and guidance and compared with the results of similar studies reported in ...

2011-05-01

424

Radioactive-electrophoretic assay of adenosine 5'-triphosphate sulfurylase activity in crude extracts with sulfate or selenate as a substrate  

Energy Technology Data Exchange (ETDEWEB)

An assay method for ATP sulfurylase is presented which employs Na/sub 2/(35)SO/sub 4/ as a substrate and measures the production of labeled adenosine 5'-phosphosulfate and 3'-phosphoadenosine 5'-phosphosulfate by low-voltage, hanging paper strip electrophoresis. The method is applicable to crude bacterial or mammalian extracts and accurately measures picomole amounts of product(s). Na/sub 2/(/sup 75/)SeO/sub 4/ can also be employed as a substrate, if the unstable radioactive product, adenosine 5'-phosphoselenate, is converted to elemental /sup 75/Se degrees by inclusion of reduced glutathione in the reaction mixture. The same paper strip electrophoretic technique can then be used to separate /sup 75/Se degrees from the radiolabeled substrate. The method also has utility for measuring any direct reduction by crude microbial extracts of radioactive selenate to selenite, ...

1989-02-01

425

Probing gluon and heavy-quark nuclear PDFs with photon + heavy quark production in pA collisions  

CERN Document Server

We present a detailed phenomenological study of direct photon production in association with a heavy-quark jet in pA collisions at the Relativistic Heavy Ion Collider (RHIC) and at the Large Hadron Collider (LHC) at next-to-leading order in QCD. The dominant contribution to the cross-section comes from the gluon--heavy-quark (gQ) initiated subprocess, making \\gamma + Q production a process very sensitive to both the gluon and the heavy-quark parton distribution functions (PDFs). Additionally, the RHIC and LHC experiments are probing complementary kinematic regions in the momentum fraction x_2 carried by the target partons. Thus, the nuclear production ratio R^{\\gamma+Q}_{pA} can provide strong constraints, over a broad x-range, on the poorly determined nuclear parton distribution functions which are extremely important for the interpretation of results in heavy-ion collisions.

2010-01-01

426

On the determination of the dose-area product during X-ray examinations  

International Nuclear Information System (INIS)

Despite its great usefulness in the performance of the recording procedures prescribed by the X-Ray Ordinance the dose-area product is much less frequently measured for X-ray exposures than during fluorscopic examinations. The great multitude of measuring units, mainly on account of different scales of the measuring equipments themselves, is a cause of uncertainty in clinical routine and should be eliminated as far as the circumstances would permit. As the determination of the organ dose is relevant only in very few cases and does not necessarily require previous measurements of the dose-area product, these are of limited practical value in the assessment of individual radiation exposures during radiographic examinations. The measurements may, however, be very helpful in determinations of the radiation dose to the total population, if the future retrievability of the values obtained is ensured. In addition to some measuring values showing past ...

427

OZONE PRODUCTION IN THE PHILADELPHIA URBAN AREA DURING NE-OPS 99  

International Nuclear Information System (INIS)

As part of the 1999 NARSTO Northeast Oxidant and Particulate Study (NE-OPS) field campaign, the DOE G-1 aircraft sampled trace gases and aerosols in and around the Philadelphia metropolitan area. Twenty research flights were conducted between July 25 and August 11. The overall goals of these flights were to obtain a mechanistic understanding of O(sub 3) production; to characterize the spatial and temporal behavior of photo-oxidants and aerosols; and to study the evolution of aerosol size distributions, including the process of new particle formation. Within the NE-OPS program, other groups provided additional trace gas, aerosol, and meteorological observations using aircraft, balloon, remote sensing, and surface based instruments (Phillbrick et al., 2000). In this article we provide an overview of the G-1 observations related to O(sub 3) production, focusing on the vertical distribution of pollutants. Ozone production rates ...

428

Interaction of x-rays and food pyrolysis products in producing oncogenic transformation in vitro  

International Nuclear Information System (INIS)

In recent years it has become evident from epidemiological and experimental data that a large number of environmental factors, including diet, play a role in modifying the incidence of cancer. Cell culture systems in which oncogenic transformation serves as an end point are powerful tools for evaluating these questions. Using such systems it has been shown recently that pyrolysis products from charred surfaces of broiled meat and fish can transform hamster embryo cells in vitro as well as produce tumors in the animal. Our studies in vitro have demonstrated the oncogenic potential of ionizing radiation in both hamster and human cells and have established in hamster cells the dose response relationship at doses ranging from 1 to 600 rad for x-rays and 0.1 to 150 rad for neutrons. The present work was aimed at evaluating whether there exists a cocarcinogenic interaction between a pyrolysis product and x-rays in their ability ...

1981-07-01

429

Excitation functions for proton-induced reactions on natural hafnium: Production of {sup 177}Lu for medical use  

Energy Technology Data Exchange (ETDEWEB)

There is an increasing interest in using radioisotopes of rare earth elements for internal radiotherapy and for imaging in nuclear medicine. {sup 177}Lu is one of the promising radionuclides. This article reports on the first measurements of the excitation function for the production of {sup 177}Lu with proton-beam energies up to 17 MeV on natural hafnium targets. The experimental cross sections for the reaction {sup nat}Hf(p,x){sup 177}Lu were obtained by the activation of a stacked-foil target and subsequent gamma spectrometry. Theoretical cross sections were calculated up to 35 MeV with the EMPIRE nuclear reaction model code. The measured and calculated cross sections were used for deriving the thick-target yields and for estimating the production of other nuclides than {sup 177}Lu. Measured production cross sections of {sup 175,176,177,178}Ta on the same target are also presented.

2009-11-15

430

Excitation functions for proton-induced reactions on natural hafnium: Production of "1"7"7Lu for medical use  

International Nuclear Information System (INIS)

There is an increasing interest in using radioisotopes of rare earth elements for internal radiotherapy and for imaging in nuclear medicine. "1"7"7Lu is one of the promising radionuclides. This article reports on the first measurements of the excitation function for the production of "1"7"7Lu with proton-beam energies up to 17 MeV on natural hafnium targets. The experimental cross sections for the reaction "n"a"tHf(p,x)"1"7"7Lu were obtained by the activation of a stacked-foil target and subsequent gamma spectrometry. Theoretical cross sections were calculated up to 35 MeV with the EMPIRE nuclear reaction model code. The measured and calculated cross sections were used for deriving the thick-target yields and for estimating the production of other nuclides than "1"7"7Lu. Measured production cross sections of "1"7"5","1"7"6","1"7"7","1"7"8Ta on the same target are also presented.

2009-11-01

431

Cooperative procurement: market transformation for energy efficient products  

Energy Technology Data Exchange (ETDEWEB)

Cooperative procurement is a variation of public purchasing which may be used as an instrument to transform the market and stimulate innovation enhancing environmental performance. The core of the procedure is the following: Coordinated by a central agency a group of buyers - public administrations, but also private companies, associations, etc. - gets together and jointly formulates a catalogue of performance requirements for a specific product truly suiting their preferences. This catalogue may contain (combinations of) requirements not yet available on the market and includes energy efficiency and/or environmental performance among other preferences important to the users. On the basis of the product requirements the buyer group launches a call for tenders, evaluates the bids received from the manufacturers and commits to buying the winning product. Thus, a market is provided for the most successful innovators in a given ...

1999-07-01

432

Carmanah Technologies Corporation 2004 annual report  

International Nuclear Information System (INIS)

British Columbia-based Carmanah Technologies is a world leader in the design, manufacture and supply of patented solar-powered light emitting diode (LED) lighting solutions. As a leading alternative energy manufacturer, it was the first company to integrate LEDs with solar chargers and battery power storage. Carmanah products have high-end assembly, minimal size, maximized performance and field-proven reliability. The products have been used in public transit applications, roadway lighting, and for general aviation lighting solutions. In 2004, their products saved the equivalent of 6,705 metric tonnes of carbon dioxide. This annual report includes information on the company's net earnings and investor profiles. The company has large markets for its products with little competition. It has a strong management team and its funding places it in a position to capitalize on current and emerging technologies. ...

2005-01-01

433

A pulse-width modulated, high reliability charge controller for small photovoltaic systems  

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of a development effort to design, test and begin production of a new class of small photovoltaic (PV) charge controllers. Sandia National Laboratories provided technical support, test data and financial support through a Balance-of-System Development contract. One of the objectives of the development was to increase user confidence in small PV systems by improving the reliability and operating life of the system controllers. Another equally important objective was to improve the economics of small PV systems by extending the battery lifetimes. Using new technology and advanced manufacturing techniques, these objectives were accomplished. Because small stand-alone PV systems account for over one third of all PV modules shipped, the positive impact of improving the reliability and economics of PV systems in this market segment will be felt throughout the industry. The results of verification testing of the new ...

1997-02-01

434

White Rose development plan amendment production volume increase  

Energy Technology Data Exchange (ETDEWEB)

In January 2001, Husky Oil Operations Limited (Husky), in joint-venture with Petro-Canada, submitted a Benefits Plan for the White Rose Development to the Canada- Newfoundland and Labrador Offshore Petroleum Board (C-NLOPB). This revised document provided the case for requesting an increase in the facility maximum daily production rate and the average annual production rate for the White Rose field from 100,000 barrels per day (bpd) as stated in the approved White Rose Development Plan to 140,000 bpd. In order to determine the potential for increasing oil production through the Floating Production, Storage and Offloading (FPSO) vessel, two things were considered, namely the proper reservoir management of the White Rose field to ensure optimum resource recovery, and the capacity of the FPSO topsides processing system and supporting utilities to accommodate increased production. This ...

2006-09-15

435

State of the energy in Lebanon  

International Nuclear Information System (INIS)

The article describes the state of the energy in Lebanon. In 1996, Lebanon consumed 4647 Ktoe as a primary energy. 97% of this energy is imported mainly polluting oil products: 1623 Ktons fuel-oil, 1379 Ktons gasoline, 930 Ktons diesel, 200 Ktons coal, 124 Ktons LPG, 107 Ktons jet-fuel/Kerosene, 109 Ktons Asphaltic products. The remaining 3% of the energy consumption is renewable energy. As for production, the state owns two refineries which are not used anymore. The year 2000 plan includes an expansion project for the Tripoli refinery and an alternative plan for the Zahrani refinery. These refineries require a total investment in order to reach a production capacity of 50000 barrels a day. The article is a description of the pollution type sources and location in Lebanon. The combustion of the total energy produces yearly more than 15 Ktons of dust, 85 Ktons of SO_2, 40 Ktons of NOX and 3500 Ktons of ...

1998-04-01

436

Welfare effects of governmental interventions with a liberalized natural gas market. The Dutch natural gas exploitation policy. Report of an introduction and a reaction  

International Nuclear Information System (INIS)

A report is given of a meeting of the Netherlands Association for Energy Legislation (NEVER), which was held in Amsterdam, Netherlands, April 2006. After the meeting a presentation was made about the report 'Government involvement in liberalised gas markets. A welfare-economic analysis of the Dutch gas-depletion policy' of the Netherlands Bureau for Economic Policy Analysis (CPB). This report analyses the welfare effects of two major components of the Dutch gas-depletion policy: the offtake guarantee for small-fields gas and the cap on production from the Groningen field. After the presentation a reaction was given to the report. Both presentations give an overview of the governmental policy and insight in the effects.

2006-06-01

437

Minimum work requirement for water production in humidification?dehumidification desalination cycle  

British Library Electronic Table of Contents (United Kingdom)

This paper presents a theoretical analysis based on the second law of thermodynamics for estimating the minimum work required for air dehumidification process to produce potable water in a humidification-dehumidification (HD) desalination cycle. The general air dehumidification process is analyzed through an equivalent path consisting of an isothermal dehumidification followed by a sensible cooling Dehumidification is treated as separation process of an ideal mixture consisting of two components, namely air and water vapor. The present analysis assumes the dead state to be the dry ambient and the final state for complete dehumidification to be saturated air at 0.01?C. Contours of the minimum work are plotted on psychrometric chart and presented as a handy engineering tool to estimate the p...

2007-01-01

438

MINERGIE modules: heat pump - heat pump/solar - wood - wood/solar; Minergie-Module Waermepumpe - Waermepumpe/Solar - Holz - Holz/Solar  

Energy Technology Data Exchange (ETDEWEB)

This research report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that examined the feasibility of setting up 'MINERGIE' low-energy-consumption module standards for the production of heat in small residential buildings. The aims of the standards and the basic idea behind the MINERGIE-modules are discussed. The concepts of the modules for heat pumps and wood-fired heating systems and their combination with solar installations are examined, as are their areas of application. The requirements placed on the modules are listed. System concepts, including simple schematics for typical installations, are presented for wood-log, wood-chippings and pellets-fired systems as well as for ground-loop and air-water heat pump systems as well as their solar-aided counterparts. The results of cost-benefit analyses are presented and questions regarding system guarantee ...

2005-07-01

439

Catalytic oxidative conversion of alkanes to olefines and oxygenates  

Energy Technology Data Exchange (ETDEWEB)

All of the direct reaction schemes described and the corresponding process schemes are still in an exploratory state. Ethylene by oxidative coupling of methane could become competitive if process schemes are developed with significantly less expenditures for separation of the product from unconverted feed. No encouragement for formaldehyde from methane can be presently derived from the existing knowledge. Liquid-phase oxidation of methane to methanol appears to be attractive but no final judgement is possible at present. Oxidative dehydrogenation of ethylene and propane look promising although further catalyst improvement is required. Acetic acid from ethane and acrylonitrile from propane have a certain potential as an alternative to present technology. The outlook for acrolein and acrylic acid from propane is less favourable; new concepts for catalyst design are necessary. (orig.)

1998-12-31

440

Adsorption of 1-butanethiol from kerosene oil and red mud  

Energy Technology Data Exchange (ETDEWEB)

Although sulfur is present in many forms in kerosene, mercaptans are most objectionable due to their obnoxious odour and corrosive action. In this study, removal of one of the mercaptans has been reported, using red mud as an unconventional adsorbent. Red mud is a waste product from aluminium producing industries and has been used as an adsorbent for the removal of sulfur compounds as well as for other purposes. Adsorption studies described in this paper indicate that low concentration and high temperature favour the removal of 1-butanethiol from kerosene oil by adsorption on red mud. A first order mechanism has been proposed to describe the adsorption in the present system. Equilibrium data at different temperatures fit well in the Langmuir isotherm equation. Thermodynamic parameters for the present system indicate the feasibility of removal of 1-butanethiol from kerosene oil by adsorption on red mud. ...

1988-06-01

441

WLUP3.0, 69 and 172 Group Cross Section Libraries for WIMS  

International Nuclear Information System (INIS)

Description or function: WLUP contains validated WIMS-D formatted cross section libraries in 69 and 172 energy group structures for nuclear reactor calculations. Materials from recently released evaluated nuclear data libraries are included. The NJOY nuclear data processing system was applied for generating the cross section files following the models and conventions built into the WIMS-D lattice code. The relevant features for the WIMS users are: - Energy group structures: 69 and 172 energy groups. - List of materials: WIMS ID, general information, source of data. - Cross sections: 69 and 172 group plots. - Resonance data: WIMS ID, temperature, background cross sections. - Goldstein-Cohen factors: Goldstein-Cohen lambda values. - Thermal scattering data: thermal scattering laws and P1 matrixes. - Fission spectrum: fission spectrum data. - Burnup data: burnup chains. - Fission product yields: fission yield tables. - Pseudo lumped fission ...

442

Transport characteristics of dehydrogenated ammonia borane and sodium borohydride spent fuels  

Energy Technology Data Exchange (ETDEWEB)

Ammonia borane (AB) and sodium borohydride (SBH) are candidate materials for on-board hydrogen storage that can be dehydrogenated upon demand. The rheological properties of the dehydrogenated by-products are important to quantify their removal and transportability from the hydrogen storage system. This paper presents visco-elastic property (elastic stiffness and viscous damping) measurements of the spent fuels obtained from AB hydrolysis, hydrothermolysis and thermolysis; and SBH hydrolysis. Smaller stiffness and larger mobility (or smaller viscous damping) indicate better transportability of the spent fuel. In addition, flow property (dynamic angle of repose and avalanching time) measurements for the hydrolysis spent fuels of AB and SBH are also presented. Comparing with the SBH hydrolysis spent fuel, the AB hydrolysis spent fuel had a lower stiffness and larger mobility, as well as lower angles of dynamic repose and ...

2010-03-15

443

The ecology of the coastal marshes of western Lake Erie: A community profile  

Energy Technology Data Exchange (ETDEWEB)

Lake Erie, the southernmost of the Laurentian Great Lakes, is narrow and relatively shallow in comparison to other Great Lakes. The lake experiences extreme water level fluctuations and storm energy restricts the development of wetlands to protected areas within embayments, lagoons, or behind barriers. However, coastal marshes of western Lake Erie fringe the shorelines of Michigan, Ohio, and Ontario and encompass an area of 268 km/sup 2/. This publication reviews the ecological data and information on the wetlands of Lake Erie, which are some of the more productive areas in the Great Lakes ecosystem. The geologic history of the Lake Erie leading to the development of wetlands, the present environment, and present wetland distribution are presented as background in the opening chapters. Biological information available for the Lake Erie wetlands is discussed in detail, and ecological processes ...

1987-02-01

444

Proceedings of the 58. annual technical meeting of the Petroleum Society of CIM : CIPC 2007 : Because technology changes everything  

International Nuclear Information System (INIS)

This conference and trade show provided a forum to present new, emerging and existing technologies that will play a key role in ensuring that hydrocarbon exploitation occurs in a sustainable manner, where costs and resource recovery are optimized while minimizing environmental impacts. The challenge of developing maturing basins, frontier lands and unconventional resources was discussed. In particular, the application of thermal recovery methods such as steam assisted gravity drainage (SAGD) for the in-situ recovery of heavy oils and bitumens was reviewed and compared with the performance of alternative enhanced energy recovery technologies such as vapor extraction (VAPEX). The conference was attended by local and international participants in the petroleum sector, including managers, engineers, technologists, geologists, and other petroleum industry specialists. The conference featured 132 presentations addressing topics such as improved ...

2007-06-12

445

Light duty mobile, portable and stationary power for military applications  

Energy Technology Data Exchange (ETDEWEB)

Hydrogenics is a leading global developer of hydrogen and fuel cell products for onsite generation and power and test systems. Hydrogenics has been working with the Canadian military since 1996, and also has contracts for portable hydrogen systems with the National American Space Agency (NASA), and the United States Army. This presentation highlighted a number of Hydrogenics' fuel cell technologies for military and commercial applications. Products included portable military generators, electrolysers and reformers, backup power systems, and regenerative satellite systems. Specifications, warranties and power capabilities for the batteries and systems were presented. Details of the company's testing facilities and procedures were provided, as well as a case study of a fuel cell hybrid vehicle. Details of the HyPORT-E 5 kW Regenerative Fuel Cell Auxiliary Power Unit were ...

2006-07-01

446

Thorium different-ligand complexes with morin as analytic form for extraction-photometric determination of thorium microamounts  

International Nuclear Information System (INIS)

Consideration is given to results of investigation into thorium complexing with morin (H_2Mor) in extraction systems containing different carboxylic acids as well as different salt background. The obtained data enabled to suggest the method of photometric determination of thorium in the form of Th(HMor)_2Benz_2 different-ligand complex (where Benz-anion of benzilic acid) with 0.25 #mu#g/ml detection limit.

1989-01-01

447

Theoretical studies of metal-phosphate interactions: interaction of Li+, Na+, K+, Be++, Mg++, and Ca++ with H2PO4- and (CH3O)2PO2-: implications for nucleic acid solvation.  

UK PubMed Central (United Kingdom)

Model phosphate-metal solvation complexes have been studied by ab-initio self-consistent-field techniques. The complexes studied include (RO)2PO2-(R = H or CH3) with Li+, Na+, K+, Be++, Mg++, Ca++,...Full Text Available

1975-10-01

448

The application of virtual instruments technique in U-H_2 experimental system  

International Nuclear Information System (INIS)

The concept of the modern data acquisition system and some functional specialties of the programming software--Visual Basic 6.0 are introduced. The construction and theory of the hardware and the designing principle of the software are described. Experimental results showed that the real-time data acquisition rate was as high as 10 times per second in the system. And the relative standard uncertainty of the measurement was less than 0.5%. (authors)

2004-11-01

449

The Fenton oxidation mechanism: reactivities of biologically relevant substrates with two oxidizing intermediates differ from those predicted for the hydroxyl radical.  

UK PubMed Central (United Kingdom)

The application of kinetic probes that allow one to determine relative reactivities of biologically relevant substrates with oxidizing intermediates in the Fenton reagent (H2O2 plus Fe2+ in acidic aqueous...Full Text Available

1994-07-05

450

Study of nanocrystallization in FINEMET alloy by active screen plasma nitriding  

International Nuclear Information System (INIS)

The nanocrystallization process of amorphous Fe_7_3_._5Si_1_3_._5B_9Nb_3Cu_1 was investigated by active screen plasma nitriding (ASPN) treatment at temperatures ranging from 410 "oC to 560 "oC for 3 h in two gas mixtures of 75% N_2-25% H_2 and 25% N_2-75% H_2 at 5 mbar atmosphere. The amorphous ribbons were then annealed under vacuum at the same time and temperatures mentioned above. The structure of the samples was analyzed using various techniques such as X-ray diffraction (XRD), atomic force microscopy (AFM) and differential scanning calorimetry (DSC). Microhardness measurements, electrical resistivity and Vibrating Sample Magnetometer (VSM) were used to study mechanical, electrical and magnetic properties of the samples, respectively. It was observed that the ASPN treatment leads to finer grain size and higher crystalline volume fraction and modifies the structural features of Fe(Si) phase. The ...

2010-02-18

451

Shuttle Showcase: STS-124  

National Aeronautics and Space Administration (NASA)

The second in a series of flights to assemble the Japanese segment of the International Space Station saw the mammoth Kibo module delivered to the complex complements of Discovery and its crew on the STS-124 mission. Kibo, the Japanese word for u201chopeu201d would house dozens of experiments and serve as a platform for external payloads brought to the complex on subsequent Shuttle flights and the Japanese u201cKounotoriu201d H-2 Transfer Vehicle cargo ship.

2011-07-10

452

Neutrophil-endothelial cell interaction. Evidence for and mechanisms of the self-protection of bovine microvascular endothelial cells from hydrogen peroxide-induced oxidative stress.  

UK PubMed Central (United Kingdom)

Bovine microvascular endothelial cells (MEC) were able to degrade the H2O2 generated by phorbol myristate acetate-activated bovine neutrophils or by glucose oxidase with a maximal capacity of 4.0 +/-...Full Text Available

1986-08-01

453

Mechanism of denting corrosion  

International Nuclear Information System (INIS)

The rapid corrosion of carbon steels in high temperature, acid chloride solutions is shown to be rate limited by the anodic reaction, 3Fe + 4H_2O = Fe_3O_4 + 8H"+ + 8e"-, based on experiments which find that the corrosion rate in 0.1M NiCl_2 solution has an activation energy of 60 kJ/ mole and is unaffected by adding NaCl or by replacing NiCl_2 with PtCl_4. (author).

454

MOS device chemical response reversal with temperature  

British Library Electronic Table of Contents (United Kingdom)

Biased above threshold (VT), pulsed photocurrent (u) measurements on windowed silicon Pd gate MOS capacitors are shifted (DV) negatively by H2/N2, whereas Au gates shift positively under NO2/air. Below VT, the shifts are reversed by adjustments of interface state population. Minor temperature increases may coax the device from inversion to depletion, inducing sign reversal of the chemical response.

2010-01-01

455

Light emission from grazing incidence interaction of light ions with clean Cu(110)  

International Nuclear Information System (INIS)

Photon yields were measured from Cu(110) bombarded by H"+, H_2"+ and He"+ with different energies. The energy dependence is different from previous studies at perpendicular incidence. A calculation of the energy dependence of resonant charge capture into the n=3 state of H is compared with experiment. (G.Q.).

1983-02-04

456

Detection of Shiga Toxin-Producing Escherichia coli Serotypes O26:H11, O103:H2, O111:H8, O145:H28, and O157:H7 in Raw-Milk Cheeses by Using Multiplex Real-Time PCR ?  

UK PubMed Central (United Kingdom)

Shiga toxin (Stx)-producing Escherichia coli (STEC) strains are a diverse group of food-borne pathogens with various levels of virulence for humans. In this study, we describe the use...Full Text Available

2011-03-01

457

Amino acid sequences that determine the nuclear localization of yeast histone 2B.  

UK PubMed Central (United Kingdom)

Histone-beta-galactosidase protein fusions were used to identify the domain of yeast histone 2B, which targets this protein to the nucleus. Amino acids 28 to 33 in H2B were required for nuclear localization...Full Text Available

1987-11-01

458

A new type of scorpion Na+-channel-toxin-like polypeptide active on K+ channels  

UK PubMed Central (United Kingdom)

We have purified and characterized two peptides, named KAaH1 and KAaH2 (AaH polypeptides 1 and 2 active on K+ channels, where AaH stands for Androctonus australis Hector),...Full Text Available

2005-06-01

459

5'-Azido-[3,6-3H2]-1-napthylphthalamic acid, a photoactivatable probe for naphthylphthalamic acid receptor proteins from higher plants: identification of a 23-kDa protein from maize coleoptile plasma membranes.  

UK PubMed Central (United Kingdom)

1-Naphthylphthalamic acid (NPA) is a specific inhibitor of polar auxin transport that blocks carrier-mediated auxin efflux from plant cells. To allow identification of the NPA receptor thought to be...Full Text Available

1992-01-15

460

Waste minimization in a non-production oriented metal finishing operation  

Energy Technology Data Exchange (ETDEWEB)

This paper provides information on activities undertaken in a non- production oriented metal finishing operation to minimize waste and conserve resources. The facility is a 6000 sq foot shop that typically only deals with prototype parts. Utilizing a plan that includes employee awareness, common sense and existing technology, a noticeable reduction in waste volume has been obtained. Initiatives that are covered include: segregation of cyanide plating solutions, elimination of copper cyanide plating, elimination of hexavalent chromium plating, elimination of vapor degreasing, changing of rinsing practices, and changing a process for cleaning of aluminum parts. Some discussion is also presented on the effectiveness of combining the technologies of physical vapor deposition and electrodeposition to help minimize waste. Plans for additional initiatives including water recycling, elimination of cyanide plating and substitution of electrodeposition ...

1991-11-01

461

Unraveling duality violations in hadronic tau decays  

Energy Technology Data Exchange (ETDEWEB)

There are some indications from recent determinations of the strong coupling constant alpha_s and the gluon condensate that the Operator Product Expansion may not be accurate enough to describe non-perturbative effects in hadronic tau decays. This breakdown of the Operator Product Expansion is usually referred to as being due to"Duality Violations." With the help of a physically motivated model, we investigate these duality violations. Based on this model, we argue how they may introduce a non-negligible systematic error in the current analysis, which employs finite-energy sum rules with pinched weights. In particular, this systematic effect might affect the precision determination of alpha_s from tau decays. With a view to a possible future application to real data, we present an alternative method for determining the OPE coefficients that might help estimating, and possibly even reducing, this systematic ...

2008-03-03

462

Transmutation of nuclear waste. Transmutatie van kernafval; Statusrapport programma Recyclage van Actiniden en Splijtingsprodukten (RAS)  

Energy Technology Data Exchange (ETDEWEB)

The most important aim of the title program is to investigate the possibility to convert long-lived actinides and mobile fission products in short-lived and stable isotopes by means of nuclear transmutation and recycling. First, an overview is given of the present situation regarding fission material waste, the origin of such waste in light water reactors and the options for interim and ultimate storage. Next, attention is paid to the aim of the the RAS program, the working method and the results so far of national and international research on the transmutation of actinides and fission products. Speculative expectations for the future are briefly outlined. The report also contains four appendices with technical aspects of the title subject: the RAS program of ECN, chemical aspects of reprocessing fission material, transmutation in fission reactors and in accelerators. 12 figs., 7 tabs., 4 appendices, 57 refs.

1993-07-01

463

The isolation of "1"3"9Ce after production by a proton-induced nuclear reaction on praseodymium  

International Nuclear Information System (INIS)

A method, based on anion exchange chromatography, is presented for the isolation of "1"3"9Ce after production by a proton-induced nuclear reaction on a thick praseodymium target. After bombardment the target is dissolved in nitric acid and "1"3"9Ce oxidised to the Ce(IV) oxidation state with bromic acid. "1"3"9Ce is then separated form the praseodymium by anion exchange chromatography on a Ag MP-1 resin column in a nitric acid - bromic acid mixture. "1"3"9Ce is sorbed onto the resin column and praseodymium eluted with the acid mixture. The bromic acid is washed out of the column with nitric acid and "1"3"9Ce finally eluted with dilute nitric acid containing sulphur dioxide.

2001-02-17

464

Symmetric deformation in A approximately 100 odd and odd-odd nuclei and its influence on fission product #beta#-decay rates  

International Nuclear Information System (INIS)

Nuclear shape changes can bring about rapid changes in nuclear properties. That such vibrational #-># symmetric rotor #-># asymmetric nucleus changes may be present in the A approximately 100 region is suggested by rapid, low-energy level density changes and unexpected #beta#-decay rate changes in several series of odd-odd and odd-mass fisions product nuclei. In order to define the nature of these nuclei we have performed measurements on a series of nuclei using JOSEF and Lohengrin mass separators, fast-chemistry, and n-capture #gamma#-ray techniques. Here we summarize the several features we find.

1983-10-24

465

Sequential chemical treatment of radium species in TENORM waste sludge produced from oil and natural gas production  

British Library Electronic Table of Contents (United Kingdom)

This paper is dedicated to the treatment of sludge occurring in frame of the Egyptian produced from oil and gas production. The activity levels of three radium isotopes: Ra-226 (of U-series), Ra-228 and Ra-224 (of Th-series) in the solid TENORM waste (sludge) were first evaluated and followed by a sequential treatment for all radium species (fractions) presented in TENORM. The sequential treatment was carried out based on two approaches `A' and `B' using different chemical solutions. The results obtained indicate that the activity levels of all radium isotopes (Ra-226, Ra-228 and Ra-224) of the environmental interest in the TENORM waste sludge were elevated with regard to exemption levels established by IAEA [International Atomic Energy Agency (IAEA), International basic safety standards f...

2009-01-01

466

Recycling of poly(methyl methacrylate) scrap in the styrene-methyl methacrylate copolymer cast sheet process  

British Library Electronic Table of Contents (United Kingdom)

Poly(methyl methacrylate), PMMA, scrap generated during the casting process for PMMA cast sheet is an industrial waste stream, which has a high impact on the PMMA production cost and environment. This paper presents an alternative way to reduce the processing cost of PMMA cast sheet and decrease industrial waste by using styrene (S) as a co-monomer with methyl methacrylate (MMA) monomer, in conjunction with recycling of PMMA scrap in the S-MMA copolymer cast sheet process. The influence of factors, such as the concentrations of S and PMMA scrap, on the preparation of S-MMA copolymer cast sheet mixed with PMMA scrap was investigated. The characterization of basic copolymer composition, the physical, and the mechanical properties of the final products were examined. The results show that it ...

2009-01-01

467

Production of rare-earth atomic negative ion beams in a cesium-sputter-type negative ion source  

International Nuclear Information System (INIS)

The desire to study negative ion structure and negative ion-photon interactions has spurred the development of ion sources for use in research and industry. The many different types of negative ion sources available today differ in their characteristics and abilities to produce anions of various species. Thus the importance of choosing the correct type of negative ion source for a particular research or industrial application is clear. In this study, the results of an investigation on the production of beams composed of negatively-charged rare-earth ions from a cylindrical-cathode-geometry, cesium-sputter-type negative ion source are presented. Beams of atomic anions have been observed for most of the first-row rare-earth elements, with typical currents ranging from hundreds of picoamps to several nanoamps.

2007-08-01

468

Production and Characterization of Monoclonal Antibodies to Mouse Germ Cells  

British Library Electronic Table of Contents (United Kingdom)

In mammals, primordial germ cells (PGCs) are generated in the extra-embryonic epiblast, and thereafter migrate into the developing gonads. Following the development of the gonads to the testes or ovaries, germ cells mature into sperms or eggs. In the present study, we report production and characterization of monoclonal antibodies (MAb) that recognize PGCs. Extracts from E12.5 mouse embryonic gonads were immunized as an antigen, and hybridomas were generated using the rat medial iliac lymph node method. The hybridoma supernatants were screened by immunohistochemical analyses of E12.5 mouse embryonic sections. The antibody, referred to herein as MAb 5B5, provided strong signals on PGCs. Moreover, immunofluorescence analyses using a variety of the tissue sections of mouse embryos revealed th...

2010-01-01

469

Normal product states for fermisions and twisted duality for CCR- and CAR-type algebras with application to the Yukawa/sub 2/ quantum field model  

Energy Technology Data Exchange (ETDEWEB)

We present sufficient conditions that imply duality for the algebras of local observables in all Abelian sectors of all locally normal, irreducible representations of a field algebra if twisted duality obtains in one of these representations. It is verified that the Yukawa/sub 2/ model satisfies these conditions, yielding the first proof of duality for the observable algebra in all coherent charge sectors in this model. This paper also constitutes the first verification of the assumptions of the axiomatic study of the structure of superselection sectors by Doplicher, Haag and Roberts in an interacting model with nontrivial sectors. The existence of normal product states for the free Fermi field algebra and, thus, the verification of the funnel property for the associated net of local algebras are demonstrated.

1982-08-01

470

Natural gas utilization in blast furnace of non-integrated pig-iron plants; Utilizacao de gas natural em altos fornos de usinas siderurgicas nao-integradas  

Energy Technology Data Exchange (ETDEWEB)

In this paper, the authors investigate the technical and economical aspects of the natural gas injection in non-integrated pig-iron plants using charcoal in the blast furnace. The effects of the natural gas injection concerning the blast furnace flame temperature, charcoal consumption, productively and permeability are analyzed. It was found that the injection is beneficial in many ways, such as in the improvement of the productivity and quality, if the flame temperature is kept within an appropriate range. In the financial-economic project`s evaluation, the cash flow for the natural gas injection was analysed considering two blast conditions: through the drying and oxygen enrichment of the air. A sensibility analysis is presented in which the internal rate of return of the investment varies according to the prices of charcoal and oxygen. 3 refs., 3 figs., 3 tabs

1990-12-31

471

Managing design and construction of the Central North Sea FPSO  

Energy Technology Data Exchange (ETDEWEB)

Shell UK Exploration and Production, operating in the North Sea on behalf of Shell UK and Esso UK is presented developing the Teal and Guillemot fields in the Central North Sea (CNS). As part of this development it contracted with Single Buoy Moorings Inc., (SBM) for the design, supply and installation of a newbuilt floating Production Storage and Offloading (FPSO) vessel. The work is executed in close cooperation between Shell Expro (Client) and SBM (Contractor) and its main sub contractors. The system is due to be installed during the third quarter of 1996. After a short description of the field development and the FPSO vessel this paper outlines the contractual arrangements and the organization set-up to perform the work. A summary of the lessons learned (by SBM) is given. The opinions expressed in this paper are entirely that of the author and may not necessarily reflect the opinion of other parties involved in the CNS ...

1996-12-31

472

Jatropha Toxicity—A Review  

British Library Electronic Table of Contents (United Kingdom)

Jatropha is a nonedible oil seed plant belonging to Euphorbiaceae family. Global awareness of sustainable and alternative energy resources has propelled research on Jatropha oil as a feedstock for biodiesel production. During the past two decades, several cultivation projects were undertaken to produce Jatropha oil. In future, the increased cultivation of toxic Jatropha plants and utilization of its agro-industrial by-products may raise the frequency of contact with humans, animals, and other organisms. An attempt was thus made to present known information on toxicity of Jatropha plants. The toxicity of Jatropha plant extracts from fruit, seed, oil, roots, latex, bark, and leaf to a number of species, from microorganisms to higher animals, is well established. Broadly, these extracts posse...

2010-01-01

473

Gluino-Squark Production at the LHC: The Threshold  

CERN Document Server

An analysis of the cross section for hadronic production of gluino-squark pairs close to threshold is presented. Within the framework of non-relativistic QCD a significant enhancement compared to fixed order perturbation theory is observed which originates from the characteristic remnants of the gluino-squark resonances below the nominal pair threshold. The analysis includes all colour configurations of S-wave gluino-squark pairs, i.e. triplet, sextet and 15 representation. Matching coefficients at leading order are separately evaluated for all colour configurations. The dominant QCD corrections, arising from initial- and final-state radiation are included. The non-relativistic dynamics of the gluino pair is solved by calculating the Green's function in Next-to-Leading Order (NLO). The results are applied to benchmark scenarios, based on Snowmass Points and Slopes (SPS). As a consequence of the large decay rate of at least one of the ...

2011-01-01

474

Explosives detector  

Energy Technology Data Exchange (ETDEWEB)

An apparatus for non-invasively inspecting an object, such as an item of luggage, for explosives material is described. It comprises a multi-channel thermal neutron inspection system having a plurality of neutron irradiation chambers. Simultaneous operation of several channels increases the maximum system throughput several times. Each chamber has a lithium neutron source which is stimulated to neutron production by a proton beam. Beam switching magnets are energised by pulsing to divert a common proton beam to each source in turn. The initial beam is generated by a radio frequency quadrupole accelerator. The advantages of this system are very low residual source activity and controllable neutron production thereby minimising safety hazards. The irradiation chamber may contain several different gamma ray detectors to identify the elements present in explosives material. In addition, a neutron radiography imaging means may ...

1991-10-02

475

Energy and reserve dispatch in a multi-zone electricity market  

Energy Technology Data Exchange (ETDEWEB)

Competitive bidding for ancillary services (A/S), in addition to bidding for energy, is increasingly recognized as an important part of electricity markets. In this paper, an LP-based approach is presented for solving the multi-product (i.e. energy and A/S products), multi-zone/area physical market dispatch problem. The approach can explicitly represent various constraints, such as reserve requirement constraints, network security limits, and sharing of constrained resource capacity (e.g. maximum unit generation) between energy and reserve. The joint dispatch method, which dispatches energy and reserve market concurrently, is extended to allow inter-zonal reserve trading in multi-zone competitive pool. Numerical examples are included to demonstrate the salient characteristics of the joint dispatch solution.

1999-08-01

476

Dietary turmeric modulates DMBA-induced p21ras, MAP kinases and AP-1/NF-?B pathway to alter cellular responses during hamster buccal pouch carcinogenesis  

British Library Electronic Table of Contents (United Kingdom)

The chemopreventive efficacy of turmeric has been established in experimental systems. However, its mechanism(s) of action are not fully elucidated in vivo. The present study investigates the mechanism of turmeric-mediated chemoprevention in 7,12-dimethylbenz(a)anthracene (DMBA)-induced hamster buccal pouch (HBP) carcinogenesis at 2, 4, 6, 10 and 12?weeks. Dietary turmeric (1%) led to decrease in DMBA-induced tumor burden and multiplicity, and enhanced the latency period in parallel, to its modulatory effects on oncogene products and various cellular responses during HBP tumorigenesis. DMBA-induced expression of ras oncogene product, p21 and downstream target, the mitogen-activated protein kinases were significantly decreased by turmeric during HBP carcinogenesis. Turmeric also diminished ...

2008-01-01

477

Determination of plutonium metal origins  

Energy Technology Data Exchange (ETDEWEB)

Forensic signatures are present in any Pu sample that can determine the sample`s origin: isotopic ratio of Pu, progeny species that grow into the sample, and contaminant species left over from incomplete purification of the Pu in fuel reprocessing. In the context of intelligence information, this can result in attribution of responsibility for the product of clandestine proliferant operations or material smuggled from existing stockpiles. A list of signature elements and what can be determined from them have been developed. Work needs to be done in converting concentrations of signature species into a quantitative forensic analysis, particularly in regard to reactor performance, but this should require only a small effort. A radiochemical analysis scheme has been developed for measuring these nuclides; more work is needed, particularly for determining fission product concentrations. A sample of Pu metal has been analyzed ...

1995-02-01

478

Corrosion problems and resistance to corrosion of materials for production of steam generators for light water reactor power plants. [Alloys I-600, I-800, I-690  

Energy Technology Data Exchange (ETDEWEB)

Briefly described is knowledge of crevice corrosion, corrosion cracking and denting. In evaluating the corrosion resistance of steam generator materials it is necessary to distinguish corrosion problems caused by the primary coolant side and by the secondary circuit side. At present tubes are manufactured of 7 austenitic alloys of a different chemical composition, and available information shows that views on their corrosion resistance differ. Greatest attention has been devoted to corrosion cracking in the presence of NaOH. Findings related to I-600, I-800, I-690 and AISI 316 are given. Corrodibility by sulfur-containing products is now being studied, namely the intercrystalline corrosion cracking caused by the presence of H/sub 2/S/sub 4/O/sub 6/. Knowledge gained in this respect is summed up.

1984-07-01

479

Consuming for production - Procurement for power production at Cernavoda NPP - Nuclear Sector  

International Nuclear Information System (INIS)

The paper presents some aspects relating to the importance of a good communication and cooperation between all factors involved in procurement process at Societatea Nationala 'Nuclearelectrica', SNN. In order to comply with the internal and international rules related to safety in nuclear field and public procurement requirements and for maintaining a high standard of operational performance of Cernavoda NPP, adequate procurement systems were developed by SNN SA. The importance of human factor and the training activities for all personnel from this chain of procurement process is the main key issue to maintain high quality of their activities considering that procurement documents are reviewed and approved before to be issued by all departments involved in procurement process. The specialized department for public acquisition is supervising that the procurement processes initiated at the level of branches, in accordance with their needs and with respect to the ...

2009-10-12

480

Chiral perturbation theory calculation for pn {yields}d{pi} {pi} at Threshold  

Energy Technology Data Exchange (ETDEWEB)

We investigate the reaction pn {yields}d{pi} {pi} in the framework of Chiral Perturbation Theory (ChPT). For the first time a complete calculation of the leading-order contributions is presented. We identify various diagrams that are of equal importance as compared to those recognized in earlier works. The diagrams at leading order behave as expected by the power counting. Also for the first time the nucleon-nucleon interaction in the initial, intermediate and final state is included consistently and found to be very important. Although the perturbative series for the production operator is expected to converge very slowly, this study provides the theoretical basis for a future evaluation of the non-resonant contributions in two-pion production reactions in nucleon-nucleon collisions. (orig.)

2011-01-15

481

Application of ultrafiltration membranes for removal of humic acid from drinking water  

British Library Electronic Table of Contents (United Kingdom)

Humic acids are primarily a result of the microbiological degradation of surrounding vegetation and animal decay and enter surface waters through rain water run-off from the surrounding land. This often gives rise to large seasonal variations, high concentrations in the wet season and lower concentrations in the dry season. Alone humic acid is just a colour problem but when present in conventional treatment processes like chlorination, carcinogenic by-products like trihalomethane and haloacetic acid are formed. This, in addition to the demand for clean potable drinking water, has sparked extensive research into alternative processes for the production of drinking water from various natural/industrial sources. One of the major areas of focus in these studies is the use of membranes in micro...

2008-01-01

482

A high-performance liquid chromatography-based radiometric assay for sucrose-phosphate synthase and other UDP-glucose requiring enzymes  

Energy Technology Data Exchange (ETDEWEB)

A method for product analysis that eliminates a problematic step in the radiometric sucrose-phosphate synthase assay is described. The method uses chromatography on a boronate-derivatized high-performance liquid chromatography column to separate the labeled product, (14C)sucrose phosphate, from unreacted uridine 5{prime}-diphosphate-(14C)glucose (UDP-Glc). Direct separation of these compounds eliminates the need for treatment of the reaction mixtures with alkaline phosphatase, thereby avoiding the problem of high background caused by contaminating phosphodiesterase activity in alkaline phosphatase preparations. The method presented in this paper can be applied to many UDP-Glc requiring enzymes; here the authors show its use for determining the activities of sucrose-phosphate synthase, sucrose synthase, and uridine diphosphate-glucose pyrophosphorylase in plant extracts.

1991-05-01

483

A Bayesian approach to analyze energy balance data from lactating dairy cows  

British Library Electronic Table of Contents (United Kingdom)

The objective of the present investigation was to develop a Bayesian framework for updating and integrating covariate information into key parameters of metabolizable energy (ME) systems for dairy cows. The study addressed specifically the effects of genetic improvements and feed quality on key parameters in current ME systems. These are net and metabolizable energy for maintenance (NEM and MEM, respectively), efficiency of utilization of ME for milk production (kL) and growth (kG), and efficiency of utilization of body stores for milk production (kT). Data were collated from 38 studies, yielding 701 individual cow observations on milk energy, ME intake, and tissue gain and loss. A function based on a linear relationship between milk energy and ME intake and correcting for tissue energy lo...

2011-01-01

484

Comparison on the growth of oxide films formed in alloy 800 and alloy 600 in an aqueous medium at high temperature  

International Nuclear Information System (INIS)

Alloy 800 and Alloy 600 are well known for their resistance to corrosion in an aqueous medium at high pressure and temperature, for which they have been widely used for more than 3 decades in different structural components of water refrigerated nuclear reactors, especially as material for the steam generator tubes (SG) in these nuclear plants. The SG tubes in the Atucha I and Embalse Nuclear Plants are made with Alloy 800. The speed of corrosion of these materials in a reactor's refrigerant medium, while very small is perfectly measurable and can be described by parabolic or logarithmic type kinetics. In other words this speed is high in the first states of growth during the formation of a protective oxide film but then drops to almost stationary values. One characteristic of these films is the formation of a double layer (or duplex): i) an internal adhering layer, of approximately constant thickness, formed by small microcrystals (#<=#0.05 mm), ii) a less adhering external one, ...

2006-12-01

485

Zero-valent iron and iron oxide-coated sand as a combination for removal of co-present chromate and arsenate from groundwater with humic acid  

International Nuclear Information System (INIS)

The combination of zero-valent iron (Fe0) and iron oxide-coated sand (IOCS) was used to remove Cr(VI) and As(V) from groundwater in this study. The efficiency and the removal mechanism of Cr(VI) and As(V) by using this combination, with the influence of humic acid (HA), were investigated using batch experiments. Results showed that, compared to using Fe0 or IOCS alone, the Fe0-IOCS can perform better on the removal of both Cr(VI) and As(V). Metal extraction studies showed that As(V) was mainly removed by IOCS and iron corrosion products while Cr(VI) was mainly removed by Fe0 and its corrosion products. Competition was found between Cr(VI) and As(V) for the adsorption sites on the iron corrosion products. HA had shown insignificant effects on Cr(VI) removal but some effects on As(V) removal kinetics. As(V) was adsorbed on IOCS at the earlier stage, but adsorbed/coprecipitated with the iron corrosion ...

2011-02-01

486

Organic livestock production in Uganda: potentials, challenges and prospects.  

Science.gov (United States)

Development in organic farming has been stimulated by farmers and consumers becoming interested in healthy food products and sustainable environment. Organic agriculture is a holistic production management system which is based on the principles of health, ecology, care, and fairness. Organic development in Uganda has focused more on the crop sector than livestock sector and has primarily involved the private sector, like organic products export companies and non-governmental organizations. Agriculture in Uganda and many African countries is predominantly traditional, less mechanized, and is usually associated with minimum use of chemical fertilizers, pesticides, and drugs. This low external input agriculture also referred to as "organic by default" can create basis for organic farming where agroecological methods are introduced and present an alternative in terms of intensification to the current ...

2011-01-12

487

On-line measurement and inspection technologies of surface properties of steel sheets; Koban hyomen hinshitsu no onrain keisoku oyobi kensa gijutsu  

Energy Technology Data Exchange (ETDEWEB)

In steel production lines such as pickling lines, cold rolling mills and coil processing lines, the needs for on-line continuous measurement of surface quality and property of products and on-line inspection of surface defects have become strong. This is because user requirements for the surface quality of various products have become severer than before and besides, expectations are running high on the side of manufacturers for higher speeds of production lines and higher quality by the adoption of automatic inspection. As for the measurement of surface quality, continuous measurements along the full length of a steel strip are required in order to overcome problems derived from off-line, batch measurements that cannot satisfy user's demands for quality assurance. As for surface defects detection, various kinds of methods have been practically applied to production lines. ...

1999-12-01

488

NAME=\\  

Wastenet

... Radiation Protection Products and Equipment Find and compare a variety of radiation protection products and equipment on the world's largest environmental industry portal. View product ...

489

The carbon balance and greenhouse effects of the Finnish forest sector at present, in the past and future  

Energy Technology Data Exchange (ETDEWEB)

In this study the greenhouse impact of the total Finnish forest sector was considered, which means that the estimated emissions and sink effects from exported forest products were also included. The forest biomass is and seems to be in the next decades the most important factor in the carbon balance of the total forest sector. The development alternatives of forest industries and waste management practices has still a remarkable influence on the greenhouse impact of the Finnish forest sector. The waste management practices in the future has an important influence on the emissions but the exact net greenhouse impact of the landfills is still uncertain. However, the methane emissions from existing landfills can be reduced essentially by gas recovery. Increased incineration and energy recovery of wood waste (and replacing fossil fuel use by it) is also a future alternative for reducing the greenhouse effects in the forest sector. The sequestration of carbon by ...

1996-12-31

490

Stability of lutein in wholegrain bakery products naturally high in lutein or fortified with free lutein.  

Science.gov (United States)

Lutein is a yellow pigment found in common foods that promotes the health of eyes and skin and is associated with reduced risk of age-related macular degeneration and cataracts. In the present study, selected high-lutein wheat and corn were milled into wholegrain flours by two mills to improve flour uniformity. The high-lutein and lutein-fortified wholegrain flours were processed into breads, cookies, and muffins to study lutein stability during baking and subsequent storage. Lutein and its isomers were separated, identified, and quantified by LC-UV/vis and LC-MS following extraction with water-saturated 1-butanol. Baking resulted in a significant reduction in all-trans-lutein and the formation of cis-lutein and cis-zeaxanthin isomers. Subsequent storage at ambient temperature had a slight impact on the content of all-trans-lutein. Effects of processing were more pronounced in lutein-fortified products, and the degradation rate of lutein was ...

2010-09-22

491

Report on a survey in fiscal 1999. Survey on industrial utilization of microorganism reaction mechanisms under anaerobic condition; 1999 nendo kenki jokenka ni okeru biseibutsu hanno kiko no kogyoteki riyo ni kansuru chosa hokokusho  

Energy Technology Data Exchange (ETDEWEB)

Industrial utilization of reaction mechanisms of microorganisms under anaerobic condition permits structuring energy saving type production processes. The present survey has investigated features of new microorganisms under anaerobic condition and the status of researches thereon inside and outside the country, and discussed their future applications. Chapter 1 compares anaerobic microorganisms and functions of microorganism under anaerobic condition with those aerobic to describe their general features, and describes the purpose of this survey and the summary of the investigations. Chapter 2 surveys the current status of technologies to utilize microorganisms under anaerobic condition. Chapter 3 outlines metabolic characteristics of the anaerobic microorganisms, and extracts functions effective for material production by different anaerobic microorganisms to describe their applicability. Chapter 4 evaluates the system ...

2000-03-01

492

Production of ultra high strength steels by turbulent water cooling equipment (TWICE); Production d'aciers haute resistance par un dispositif de refroidissement a turbulence controlee  

Energy Technology Data Exchange (ETDEWEB)

A new industrial process allowing to reach very high cooling rates in the cooling section after soaking of a continuous annealing line for steel sheets is presented. This process constitutes the successful conclusion of a long term research programme, jointly carried out at CRM and Arcelor Cockerill-Sambre for three years, including laboratory experiments, pilot scale trials and several industrial campaigns. It is running on from developments performed in the framework of the HOWAQ (Hot Water Quench) process. The process successively combines a moderate cooling step (600 deg C/s for 0.8 mm thick strips), in boiling water, and a faster cooling step (above 700 deg C/s), by impinging turbulent cold water in a box. Its main features are simplicity, resulting from advanced developments, soundness, flexibility and cooling homogeneity. As treated steel products are characterized by improved mechanical properties, outstanding surface quality (corrosion ...

2003-08-01

493

Localization explore of electrical and I and C equipments in Daya Bay Nuclear Power Station  

International Nuclear Information System (INIS)

The supply of electronic instrumentation and controlling (I and C) equipments in Daya Bay Nuclear Power Station depends on importation up to now, however, reliable supply of spare parts is presently threatened by many factors. Consequently, Daya Bay Nuclear Power Station tries to localize these equipments. According to a survey, China has possessed the ability to undertake the research, development and production of the I and C system in nuclear power independently. We propose that localization should firstly starts with the production of replacement board and parts for analogical I and C system, gradually leads to the substitution of system cabinet units, and finally realize the independent research, development and production of advanced digital main control system. A series of prominent problems of producing nuclear grade I and C equipments are focused on the designing, manufacturing, testing and ...

2007-10-01

494

Hydroelectric power in Switzerland: large growth potential by increasing the installed power  

International Nuclear Information System (INIS)

Due to its important hydroelectric power generation facilities (about 525 plants with a total power of 13,314 MW producing about 35.3 TWh annually) Switzerland plays an important role in the interconnected European power system. Large artificial storage lakes in the Swiss Alps can generate peak power during hours of highest demand: 9700 MW are available from accumulated energy and the total power of pumped-storage facilities amounts to 1700 MW. The latter allow refilling the reservoirs at periods of low power demand and generating power at periods of peak demand. In the case of favorable conditions, the yearly average power production could be increased by 6% and the production during the winter period (October to March) by 20% by the year 2020. However, looking forward to the year 2050, the annual production is expected to decrease by 3% despite a possible extension of hydropower. This decrease is due to the enforcement of ...

495

Feasibility study for an ethanol plant in New Orleans, Louisiana. Book one. Executive summary. Volume 1 through 3  

Energy Technology Data Exchange (ETDEWEB)

The findings of a 9-month study of the feasibility of constructing and operating a 35 million gallon per year fermentation ethanol plant in the New Orleans area are presented. The unique features studied are the use of corn screenings, elevator by-products, and damaged grains as feedstock, and the use of municipal solid waste (MSW) as the process fuel. The plant will require investment outlays of $146 million, and the unit production cost for ethanol will be about $1.43 per gallon. The ethanol will be sold in the Louisiana and Texas markets. In Louisiana, gasohol benefits from an 8 cent per gallon state excise tax exemption as well as from the 4 cent per gallon federal excise tax exemption. The by-product, DDGS, will be sold to the overseas market. A large quantity of feedgrains and feedstuffs are exported from the port of New Orleans, and the plant's DDGS will have a price advantage over ...

1982-04-01

496

Evaluation of red mud as pozzolanic material in replacement of cement for production of mortars; Avaliacao da lama vermelha como material pozolanico em substituicao ao cimento para producao de argamassas  

Energy Technology Data Exchange (ETDEWEB)

Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial ...

2010-07-01

497

Evaluation of red mud as pozzolanic material in replacement of cement for production of mortars  

International Nuclear Information System (INIS)

Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial ...

2010-11-21

498

Effects of biomass-generated producer gas constituents on cell growth, product distribution and hydrogenase activity of Clostridium carboxidivorans P7{sup T}  

Energy Technology Data Exchange (ETDEWEB)

In our previous work, we demonstrated that biomass-generated producer gas can be converted to ethanol and acetic acid using a microbial catalyst Clostridium carboxidivorans P7{sup T}. Results showed that the producer gas (1) induced cell dormancy, (2) inhibited H{sub 2} consumption, and (3) affected the acetic acid/ethanol product distribution. Results of this work showed that tars were the likely cause of cell dormancy and product redistribution and that the addition of a 0.025{mu}m filter in the gas cleanup negated the effects of tars. C. carboxidivorans P7{sup T} can adapt to the tars (i.e. grow) only after prolonged exposure. Nitric oxide, present in the producer gas at 150ppm, is an inhibitor of the hydrogenase enzyme involved in H{sub 2} consumption. We conclude that significant conditioning of the producer gas will be required for the successful coupling of biomass-generated producer gas with fermentation to produce ...

2006-07-15

499

Absorption of the atmospheric CO{sub 2} by oceanic biota near the air-sea interface  

Energy Technology Data Exchange (ETDEWEB)

The oceanic phytoplancton productivity may essentially influence the total rate of the atmospheric CO{sub 2} absorption by the ocean - that is, a considerable amount of CO{sub 2} will be taken-up in the 50 micrometers thick layer near the air-sea interface. Even if phytoplancton production constitutes only 5% of the total oceanic biota production, this will increase the rate of CO{sub 2} absorption more than twice compared with the present estimates. The reason is that metabolic activity of phytoplancton leads to the emergence in a thin scin (50 micrometers, the average size of phytoplancton cells) layer near the water surface of an additional minimum in the CO{sub 2} partial pressure profile and of an additional maximum of {Delta} {sup 13}C in the same area. These two extremums cannot be detected if the corresponding characteristics are averaged over any microscopic area in the well mixing layer that ...

1997-12-31

500

A gas-jet ECR ion source at TRIGA-SPEC  

International Nuclear Information System (INIS)

The TRIGA-SPEC experiment has been installed recently at the research reactor TRIGA Mainz. Ground state properties like masses, charge radii, spins, and moments of short-lived nuclides can be determined with very-high precision using the Penning trap mass spectrometer TRIGA-TRAP, and the collinear laser spectroscopy setup TRIGA-LASER. Short-lived neutron-rich radionuclides in the mass range 80 < A < 140 are produced by thermal neutron induced fission of e.g. U-235, Pu-239 or Cf-249, respectively. For the extraction and ionization of the fission products a gas-jet system is coupled to a 2.45-GHz ECR ion source for the production of singly charged ions. The gas-jet has been tested on-line and fission products have been extracted. First off-line tests of the ion source have been performed successfully with argon gas. The results of the commissioning test of the ion source and the on-line coupling of the experiments are ...

2010-03-08