Energy Technology Data Exchange (ETDEWEB)
Electricity is a universal energy and one of the driving powers of civilisation. World-wide, future developments like growing economies and structural changes in industry, a higher standard of living and a bigger world population - are impossible without appropriate supply of power and electricity. An expert of Siemens Power Generation presents his views. (orig.)
2006-11-15
Energy Technology Data Exchange (ETDEWEB)
The purpose of this project was to build a long-range, parallel hybrid gas/electric vehicle capable of driving beyond the communter capabilities of series hybrid vehicles. It was envisioned that since the gas engine would be able to independently propel the car when needed and that the electric motor would be capable of doing the same, then you have a very desirable situation where this car can operate much more cheaply on electricity for the short distance runs under approximately 60 miles and also be able to propel the vehicle via the gas engine on the long-distance trips. During the time the car would be operating in the gas engine mode, it would be also recharging the 16 deep cycle batteries via the electric motor now being used as a generator. Then, even on long-distance trips, the electric ...
1985-01-01
International Nuclear Information System (INIS)
Australian electricity markets and natural gas markets are undergoing rapid reform. Choosing among electricity generation modes is a key issue. Such choices are affected by expectations about the future structure of these markets and future technologies, and how they affect costs and emissions. In the research reported in this paper, the MARKAL model of the Australian energy system is used to evaluate the competitive position of natural gas fired combined cycle gas turbines (CCGTs) in the energy sector as a whole. Competing in the sector are large-scale electricity generation technologies such as refurbished existing coal fired stations and advanced forms of coal fired generation. The modelling incorporates new data on electricity supply technologies and options.
2003-02-01
System for the co-production of electricity and hydrogen
Described herein is a system for the co-generation of hydrogen gas and electricity, wherein the proportion of hydrogen to electricity can be adjusted from 0% to 100%. The system integrates fuel cell technology for power generation with fuel-assisted steam-electrolysis. A hydrocarbon fuel, a reformed hydrocarbon fuel, or a partially reformed hydrocarbon fuel can be fed into the system.
2007-10-02
Engine use of producer gas, experiences and requirements
Energy Technology Data Exchange (ETDEWEB)
The most effective way to generate electricity out of biomass is the gasification and the use of the gas in a gas engine. The conversion of the organic carbon with the gasification of biomass is higher than 95 %. Depending on the gasification concept, the efficiency of gasifiers is found between 70 and 90 %. If the pyrolysis gas is used in a gas engine, an electric efficiency of about 26 % referring to the primary amount of energy can be obtained. With efficient gas cleaning (cleaning for tar and dust), pyrolysis gas is well qualified for engine combustion. Through modern state of engine controlling there are ways to have complete control of the fluctuations in the gas composition. Furthermore, the minor calorific value of offered wood gas poses no problem ...
1999-07-01
The low-current low-temperature plasma generators
Energy Technology Data Exchange (ETDEWEB)
In this article, the results of low-current gas-discharge plasma generator investigations carried out by a group of scientists from the Kazan' Aviation Institute are presented. When considered necessary, the results are compared with the data obtained by other authors. The basic configurations and theoretical calculation peculiarities of plasma generators are described. The electrical, thermal and energy characteristics of discharges in gas flows, as well as summarised empirical formulae and experimental data necessary for calculations and design of plasma devices are presented. (author)
2000-07-01
Electrical grid stability and its impact on nuclear power generating stations
Energy Technology Data Exchange (ETDEWEB)
Electrical power is generated by steam turbines (steam being produced by coal, oil, gas or nuclear reactors), hydro units, gas turbines, internal combustion engines, jet engines, and pumped storage plants. Nuclear Power Plants generate only 15% of the total electrical power in the US. Nuclear Power Plants being cheaper to run are generally base loaded. The pumped-storage and gas turbine plants have ideal characteristics for peaking duty. In the pumping mode, pumped storage plants are used to provide additional system load and in the generating mode, they supply reactive power during peak load demands. Gas turbine plants have higher running costs, but are used as peaking units with a fast start capability. Fossil power plants need a minimum of 1 hour to stabilize expansion in the boiler and turbine ...
1997-12-31
The report gives results of an analysis of the effect of the availability of a flue gas desulfurization system on the ability of an individual power plant to generate electricity at its rated capacity. (The availability of anything is the fraction of time it is capable of service, whether or not it is actually in service.) Also analyzed are its effects on a power generating system (a group of several coal-, oil-, and gas- fired power plants plus nuclear and hydroelectric plants).
1978-03-01
British Library Electronic Table of Contents (United Kingdom)
The rational use of energy has become a priority for all industries in Brazil, mainly after the energy rationing in 2001. Methodologies to quantify and improve the performance of plants that consume and generate electricity and thermal energy are being used to reach this goal. Exergoeconomic analysis provides a complete diagnosis of a plant, both in exergetic and in monetary values. This study shows the methodology used to assess the power generation system of the Companhia Siderurgica Tubarao (CST). The current system is based on a regenerative Rankine cycle using two gases from steel production - blast furnace gas (BFG) and coke oven gas (COG) - to generate electric power and occasionally steam for the process. Use of the Theory of Exergetic Cost allowed determination of monetary and exe...
2009-01-01
New models needed to manage gas supply, APPrO conference hears
International Nuclear Information System (INIS)
Details of a 1 day conference designed to create more efficient interactions between the gas supply and electricity systems in Ontario and new models for gas supply and the electricity system were presented. Market efficiency, generators' perspectives on critical gas issues, an overview of the North American gas and an outline of issues concerning Ontario were discussed. A natural gas industry forecast and issues concerning marketers and producers were presented. The terms on which gas is bought and sold were discussed. Regulatory tools, cost allocation and issues relating to unbundling were also presented. Infrastructure needs were reviewed, as well as basic market structures. It was suggested that appropriate commercial service options need to be developed and approved, including cross-utility ...
2005-08-01
Plasma Treatment within Dielectric Fluids.
A dielectric liquid having entrained bubbles of gas or vapor is subjected to an electric field applied between spaced electrodes (112, 116) which generates microdischarges (and thus plasma) within the bubbles, allowing modification of the properties of th...
2003-01-01
Internalizing externalities of electricity generation: An analysis with MESSAGE-MACRO
Energy Technology Data Exchange (ETDEWEB)
This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NO {sub X} , and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired ...
2007-02-15
Internalizing externalities of electricity generation: An analysis with MESSAGE-MACRO
Energy Technology Data Exchange (ETDEWEB)
This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NOX, and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired plants. ...
2007-02-15
Gas fired combined cycle plant in Singapore: energy use, GWP and cost-a life cycle approach
Energy Technology Data Exchange (ETDEWEB)
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for ...
2005-08-15
Gas fired combined cycle plant in Singapore: energy use, GWP and cost-a life cycle approach
International Nuclear Information System (INIS)
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for ...
2005-08-01
Ballard fuel cells and the changing energy landscape
Energy Technology Data Exchange (ETDEWEB)
The numerous challenges facing the North American electric utility industry were discussed. In addition to competition, electric utilities are faced with low demand growth, public pressure to avoid adding transmission and distribution capacity, and strict environmental requirements. In view of these developments, large central generation additions that have been industry norm until recently, do not always make economic sense in the current environment. Instead, smaller, distributed additions to generating capacity is becoming the new norm. Small-scale on-site generating capacity has the added advantage of reducing the need for expensive high-voltage transmission lines. The Ballard generation system described here is a modular, efficient fuel cell-based solution to implementing distributed power concepts. The system is natural gas fueled, ...
1997-02-01
Electric power generation. Thermal power generating systems. 2. rev. and enl. ed.
International Nuclear Information System (INIS)
This is a manuscript for a lecture contents: 1. Steam power and fundamentals of the steam power process, 2. conventional, nuclear and other steam generation processes, 3. cooling systems for steam power plants, 4. gas turbine power plants and combined-cycle power plants, 5. cogeneration, 6. development of thermal power plants and environmental effects. (orig.).
Electric power generation. Thermal power generating systems
International Nuclear Information System (INIS)
This is a manuscript for a lecture contents: 1) Steam power and fundamentals of the steam power process, 3) conventional, nuclear and other steam generation processes, 4) cooling systems for steam power plants, 5) gas turbine power plants and combined-cycle power plants, 6) cogeneration, 7) development of thermal power plants and environmental effects. (GL).
High-tension corona controlled ozone generator for environment protection
International Nuclear Information System (INIS)
Engineering details of a high voltage driven corona-plasma ozone generator are described. The plasma diode of generator has coaxial cylindrical geometry with cathode located inside anode. Cathode is made of a large number of radial gas nozzles arranged on central tubular mast which admits oxygen gas. The sharp endings of the nozzles along with a set of corona rings create the high electric field at the cathode required for formation of dense corona plume responsible for O_3 evolution. A model of coronal plasma generation and ozone production is presented. The plasma formation is strongly dependent on the electric field and temperature in side diode where a high electron density in a low temperature negative corona is suited for high ozone yields. These are established by suitable regulation of A-K gap, voltage, oxygen pressure, and ...
2010-02-01
Economic and environmental advantages of natural gas-fueled combined-cycle electric power generation
International Nuclear Information System (INIS)
The outlook for natural gas (from both supply and price perspectives) has improved dramatically since the late 1970s, and significant advances have been made in electrical generation technologies which use gas. For example, gas-fired combined-cycle turbine units have become even more efficient and reliable. These units can be installed quickly (12 to 24 months versus 8 to 15 years for coal and nuclear units), and they may be brought on-line in small incremental blocks. This modular construction feature offers greater flexibility to utility planners, and the relatively low capital cost of combined-cycle units reduces financial uncertainties. The purpose of this chapter is to compare two electric power generating options, a new coal-fired powerplant and a new natural gas fired combined-cycle unit, from both economic and ...
Tritium monitor with improved gamma-ray discrimination
Energy Technology Data Exchange (ETDEWEB)
Apparatus and method for selective measurement of tritium oxide in an environment which may include other radioactive components and gamma radiation, the measurement including the selective separation of tritium oxide from a sample gas through a membrane into a counting gas, the generation of electrical pulses individually representative by rise times of tritium oxide and other radioactivity in the counting gas, separation of the pulses by rise times, and counting of those pulses representative of tritium oxide. The invention further includes the separate measurement of any tritium in the sample gas by oxidizing the tritium to tritium oxide and carrying out a second separation and analysis procedure as described above.
1985-01-01
Energy Technology Data Exchange (ETDEWEB)
Biogas supply to the public gas grid is a new option discussed in the most recent publication of Fachagentur Nachwachsende Rohstoffe (FNR) e.V. The biogas is purified, upgraded to natural gas quality and fed into an existing gas grid. Once there, it can be transported across long distances and also used for electric power generation at the consumer side. The study investigates inhowfar and in what instances this method is feasible and promising. It discusses the technical background and the regional potential of biogas. Seven model biogas systems are presented as examples. (orig.)
2006-07-01
Monitoring of power generation from landfill gas at Cory Environmental Ltd., Mucking Marshes
Energy Technology Data Exchange (ETDEWEB)
The energy recovery scheme at Mucking Marshes landfill site, operated by Cory Environmental Limited, has been in operation since October 1991. Using landfill gas abstracted from the site, a gas turbine generates up to 3.2 MW net electric power for export. Operation and performance of the scheme has been monitored over the period January 1995 to August 1996. Overall performance since the first use of the turbine has also been studied, and has shown reliable and profitable operation. The capital cost of the gas turbine and gas compressor plant was approximately 1.8 million. Actual gas collection wells, pipework, pumping and monitoring facilities, while essential to the scheme, are considered part of the gas control equipment needed for the landfill site. Based on a notional electricity selling price of ...
1996-12-31
Entering the Canadian mainstream. [The independent energy market in Canada
Energy Technology Data Exchange (ETDEWEB)
This article examines the developing market for independent power projects in Canada. The topics of the article include bidding in Ontario, the Quebec market, powering British Columbia, and market forces at work in Canada. Discussed are current projects in all stages of completion from bidding to production and includes gas-fired cogeneration, gas-fired combined-cycle electricity generation and cogeneration, wood-waste fired plants, repowering of existing utility plants, and hydroelectric power plants.
1992-04-01
Regional application of natural-gas-fired combined-cycle power generation
Energy Technology Data Exchange (ETDEWEB)
The results of a study assessing natural-gas-fired combined-cycle (GFCC) power generation in the electric-utility sector are presented. This study quantified the economic benefits attributable to GFCC generation and examined the characteristics of GFCC technology that produce these benefits and the ways that these benefits vary among regions in the country. The impacts of changes in important economic parameters (capital cost, fuel price, etc.) as well as the impact of advances in GFCC technology were considered. Use of GFCC technology in the electric-utility sector could play an important role in a least-cost planning strategy and thereby provide significant benefits to the utilities and their customers. Potential benefits include reduced capital and operating costs, more effective matching of load growth and capacity additions, and greater system reliability. 8 refs., 3 tabs.
1989-01-01
Thermodynamic modeling of integrated SOFC systems for power and hydrogen productions
International Nuclear Information System (INIS)
Electricity generation from natural gas in gas turbine units can be made substantially more efficient by preliminary methane conversion to a synthesis gas containing hydrogen and carbon monoxide and/or by the use of some of the synthesis gas produced in industry. An alternative improvement involves the introduction of solid oxide fuel cells (SOFCs) and the use of the synthesis gas in them. In this study, a modified scheme of gas turbine cycle that includes an SOFC, a membrane reactor (instead of a traditional combustion chamber), and a catalytic reactor to perform methane conversion to produce hydrogen (synthesis gas) is proposed. Variations of the energy and exergy efficiencies of the integrated system with operating conditions are provided, showing, for example, that SOFC efficiency is enhanced if ...
The effect of neutrals on the performance of plasma opening switches
Energy Technology Data Exchange (ETDEWEB)
The authors address the question of the limitations on voltage and current transfer to loads in magnetic storage systems utilizing microsecond conduction time plasma opening switches. They propose that the limitation of performance results from neutral atoms that are not entrained into the ionized material that is driven by the magnetic field of the rising generator current. Evidence in support of this proposition is gathered from experiments performed on the Ace-4 and Hawk generators. They set forth a theory to describe the effect of neutrals on the electrical performance of plasma opening switches. The neutral gas is assumed to be present in the region between the moving plasma mass and the generator, primarily in the region in which the plasma is injected initially. The essential elements of the theory are a weak photoionization source to seed the gas with a ...
1996-12-31
Small, efficient thermophotovoltaic power supply. Final report, 21 February 1997--21 February 1999
Energy Technology Data Exchange (ETDEWEB)
The objective of this contract is to design and build a small, lightweight, stand-alone thermophotovoltaic electric generator, capable of at least 100 Watts useful output for charging 24V batteries. The prototype generator built consists of a pre-mixed burner, a cylindrical selective emitter mantle surrounded by six silicon photovoltaic concentrator arrays. The arrays are cooled with forced-air heat exchangers using self-powered fans. The generator, operated at 117,00 W (40,000 BTU/hr) of fuel input rate, produces 122 W of electrical power at 1.0% of efficiency. The cooling and pre-mix fans consume 35 W of electrical power resulting in a net 85 Watts of electrical output for charging batteries. The generator`s output is capable of continuous charging five 12/24V batteries over 10 hours with a 9.07 Kg (20 lbs.) of propane ...
1999-04-23
Report on definitional mission: Hungary gas-fired power plants. Export trade information
Energy Technology Data Exchange (ETDEWEB)
The U.S. Trade and Development Program (TDP) had received a request from the Hungarian Electricity Board (MVMT) for assistance in support of a feasibility study program to: (1) install new generation capability based on gas/oil fired combined cycle power plants, and (2) retrofit/refurbish a number of aging coal and oil fired steam plants. A Definitional Mission (DM) recommends that TDP fund the requested feasibility studies for new gas/oil fired combined cycle capabilities discussed in the Terms of Reference (TOR). Hungary will need to install significant new power capacity between now and the end of the century. Gas/oil fired combined cycle plants present probably the only option to install capacity rapidly. There is an opportunity for U.S. firms to supply technology and services with respect to these advanced power generation technologies.
1991-02-28
Energy Technology Data Exchange (ETDEWEB)
The theoretical analysis of a partially-ionized hydrogen gas flow (gas temperatures of approximately 10,000 to 20,000 K) through a particular class of magnetohydrodynamic (MHD) generators and the preliminary design of these MHD generators as open cycle, electric power supplies are performed. Analysis of the gas flow through these ultra-high temperature MHD generators requires a coupled gas dynamics/radiative heat transfer solution. Gas dynamics are modeled by a set of quasi-one-dimensional, nonlinear differential equations which account for friction, convective and radiative heat transfer and the interaction between the ionized gas and applied magnetic field. Radiative heat transfer is modeled using non-gray, absorbing-emitting two- and three-dimensional P-1 approximations which ...
1990-01-01
Energy Technology Data Exchange (ETDEWEB)
CRE is the French commission for energy regulation. CRE's remit is to assist in ensuring the proper operation of the electricity and natural gas markets for the benefit of the end-user. In particular, CRE ensures that the conditions of access to electricity and natural gas transmission and distribution systems do not hinder the development of competition. It monitors, for the electricity and natural gas sectors, all transactions made between suppliers, traders and producers, all transactions made on the organised markets and cross-border trading. It ensures that suppliers, traders and producers propose offers that are consistent with their financial and technical constraints. It monitors the implementation of and compliance with regulations giving consumers the right to choose their supplier in a competitive market, and allowing new suppliers to enter ...
2008-07-01
A new efficient and simple concept for electric power generation and its thermodynamic optimization
Energy Technology Data Exchange (ETDEWEB)
Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 55% for electric power generation. Nevertheless the reserve of natural gas is more limited compared to the reserve of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverized coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, a ...
1994-12-31
Conversion of the Midland nuclear station
Energy Technology Data Exchange (ETDEWEB)
The authors report how the Midland cogeneration venture (MCV) is repowering the incomplete Midland nuclear plant to operate as a gas-fired combined cycle cogeneration facility. They discuss how their company is responsible for performing engineering, procurement, licensing, construction, start-up, training, and operational assistance for this facility. As shown, twelve gas turbine generator sets supply heat to twelve heat recovery steam generators (HRSGs), which are headered together on the steam side to provide energy to either of two existing steam turbine generators. This combination of equipment enables approximately 1,380 MWe of electrical generation capability, while supplying an average steam flow of 629,000 lbs/hr to an adjacent Dow Chemical Company pant. The MCV facility will also provide 60 MW of electric power ...
1988-01-01
Greenhouse gas emission inventory based on full energy chain analysis
International Nuclear Information System (INIS)
Methodology, characteristics, features and results obtained for greenhouse gases within the recent Swiss LCA study 'Environmental Life-Cycle Inventories of Energy Systems' are presented. The focus of the study is on existing average Full Energy Chains (FENCHs) in the electricity generation mixes in Europe and in Switzerland. The systems, including coal (hard coal and lignite), oil, natural gas, nuclear and hydro, are discussed one by one as well as part of the electricity mixes. Photovoltaic systems are covered separately since they are not included in the electricity mixes. A sensitivity analysis on methane leakage during long-range transport via pipeline is shown. Whilst within the current study emissions are not attributed to specific countries, the main sectors contributing to the total GHGs emissions calculated for the various FENCHs are specified. (author). 10 refs, 10 figs, 9 ...
1996-07-01
Energy Technology Data Exchange (ETDEWEB)
The present project examined the operating characteristics and application possibilities of a new, compact combined heating and electricity generating unit with a thermal output of 14,5 kW and a generating capacity of 5,5 kW. Such a module was installed in a plant in Arlesheim (Canton of Basel-Country) and subject to performance measurements. The small heating and generating plant is designed for cyclic operation (without heat storage) and is very compact and low in cost. The heating and generating unit conforms to all Swiss regulations relating to electrical installations and air pollution control. The NO{sub x} emissions of the unit (400 mg/m{sup 3} in steady state operation) are above the limits of LRV 92 (80 mg/m{sup 3}), but the regulation does not apply for units in this power range. The electricity generation ...
1995-12-01
Significance of microstructure for a MOCVD-grown YSZ thin film gas sensor
Energy Technology Data Exchange (ETDEWEB)
The authors report the fabrication and characterization of a low temperature (200--400 C) thin film gas sensor constructed from a MOCVD-grown yttria-stabilized zirconia (YSZ) layer sandwiched between two platinum thin film electrodes. A reproducible gas-sensing response is produced by applying a cyclic voltage which generates voltammograms with gas-specific current peaks and shapes. Growth conditions are optimized for preparing YSZ films having dense microstructures, low leakage currents, and maximum ion conductivities. In particular, the effect of growth temperature on film morphology and texture is discussed and related to the electrical and gas-sensing properties of the thin film sensor device.
1996-11-01
Energy Technology Data Exchange (ETDEWEB)
This paper was produced as an input to the Swiss Confederation's 'Electricity Perspectives 2035' study made by the Swiss Federal Office of Energy (SFOE). A concept for the combined use of wood and natural gas in a combined-cycle power station is presented. The gasification of wood to provide fuel for the gas turbines and waste-heat boilers of such power stations is proposed as an alternative to just burning wood to provide heat for steam generators. Figures are quoted on the quantities of biomass and wood usable for energy applications in Switzerland. The energetic and financial efficiencies of wood-powered generation of heat and electricity are examined, as are the investments necessary and the costs incurred. Comparisons are presented between wood from forests, sawmill-wastes, scrap wood and natural gas as fuels.
2005-07-01
Catalytic oxidation of the unburnt fuel for the efficient production of electric energy
Energy Technology Data Exchange (ETDEWEB)
Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 58% for electric power generation. Nevertheless the reserves of natural gas are more limited compared to the reserves of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverised coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, ...
1995-12-31
Economical evaluation of electricity generation considering externalities
International Nuclear Information System (INIS)
The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle-natural gas fired system. A photovoltaic system still uses ...
2002-02-01
The formation and removal characteristics of aerosols in ammonia-based wet flue gas desulfurization
British Library Electronic Table of Contents (United Kingdom)
The characteristics of aerosol generation were studied experimentally in an ammonia-based wet flue gas desulfurization process. Particle size distributions and concentrations, morphologies and compositions before and after desulfurization were measured using an electrical low pressure impactor and scanning electron microscopy, respectively. The results show that aerosols can be generated between ammonia and sulfur dioxide resulting in gas-phase reaction and the aerosol concentration at the outlet of scrubber is significantly higher than at the inlet. Before desulfurization the particles are primarily silica-alumina minerals including O, Al, Si and C, while after ammonia-based desulfurization aerosol particles have smooth surfaces with regular structures, such as cubic and prismatic crystal...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam-cycle is the conventional conversion method; however total energy conversion efficiencies for this type of process are only slightly over 30%. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40%. Conversion processes based on gasification offer efficiencies above 50%. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. This process is concerned with the removal of H{sub 2} from coal gas through an electrochemical membrane technology.
1996-03-01
Gas and steam turbines: Power from fire; Gas- und Dampfturbinen: Kraft aus dem Feuer
Energy Technology Data Exchange (ETDEWEB)
More than 200 years after the birth of the steam engine, the first thermal engine ever invented, thermal engines such as steam turbines, gas turbines or internal combustion engines are still driving most generators for electric power generation, most machines, and most vehicles, and this will remain so until far into the next century. (orig.) [Deutsch] Mit Waermekraftmaschinen wie Dampfturbinen, Gasturinen und Verbrennungsmotoren werden auch heute - mehr als 200 Jahre nach der technischen Reife der Dampfmaschine (der ersten Waermekraftmaschine) - die meisten Generatoren zur Stromerzeugung, die meisten Arbeitsmaschinen und die meisten Fahrzeuge angetrieben. Und dabei wird es auch bis weit in das 21. Jahrhundert bleiben. (orig.)
1996-02-01
Modern concept for ethanol distilleries: maximization of the electricity surplus
Energy Technology Data Exchange (ETDEWEB)
Once again Brazil faces the possibility of an electricity shortage in the near future. The low level of rain and the consequent reduction of hydroelectric reservoirs (hydroelectric energy represents almost 80% the total Brazilian electricity generation) led to the dispatch of thermal plants based on natural gas and/or fuel oil. However, the recent crisis regarding the Bolivian natural gas supply to Brazil increased the risk of a shortage of this energy source. Hence, the uncertainty of the electricity supply scenario is pushing the electricity prices up in the near future. A possible alternative to increase the electricity supply is the maximization of the electricity surplus in sugarcane mills. Back in 1970's and 1980's, cogeneration plants in sugarcane mills were primarily ...
2008-07-01
Energy Technology Data Exchange (ETDEWEB)
This study is part of a greater project from IPT (Sao Paulo's Institute of Technology), which foresaw an energetic use for elephant-grass (Pennisetum purpureum). Biomass gasification is an sustainable option for energy supply, which presents low pollutants emission rate and allows - through the global cycle of growing and consumption of feedstock (vegetables), a balance between consumption and production of carbonic gas, preventing an increase of the carbonic gas levels in the atmosphere. A gasifier was built with internal diameter of 400 mm and total height of 4600 mm . The equipment was tested for gasification of elephant-grass (Pennisetum purpureum) at a 100 kg/h rate. The equipment was tested and some constructive faults were detected. In the countryside, this biomass is commonly used for cattle feeding It was evaluated an adequate diesel-electric-generator. to work at hybrid regime, using 70% biomass ...
2000-07-01
The role of small and medium reactors in the energy security of a country, IRIS example
International Nuclear Information System (INIS)
Nuclear options for electricity generations are assessed in this paper. Probabilistic (stochastic) method is used for economic comparison of nuclear power plants, wind plants and natural gas fired plants. Optimal nuclear power plant size is also discussed. IRIS is presented as a representative of small and medium reactors
2009-05-26
The Role of Electronegative Impurities in Ozone Generation by High Pressure Discharges
International Nuclear Information System (INIS)
The high pressure discharges (pulsed or D C corona, barrier, gliding and the others), have been studied both experimentally and theoretically as sources of low temperature plasma for pollution control technologies. The potential of electrical discharge methods has been demonstrated for the decomposition of many types of VOC. The air or oxygen are used as a feed gas in which pollutant is diluted. The ozone production in air or oxygen in such discharges is also discussed
1999-07-11
Continuous emission monitoring -- Data acquisition and handling system for management
Energy Technology Data Exchange (ETDEWEB)
This paper describes New York State Electric and Gas Corporation`s concept for a comprehensive, centrally located data system for management of their continuous emission monitoring systems (CEMS) data. The topics of the paper include the power system`s mix of generating units; data reporting requirements; data base management; nitrogen oxides compliance tracking; sulfur dioxide, nitrogen oxides, carbon dioxide and flow monitoring; and allowance tracking.
1995-09-01
Coal-fired combined-cycle plants are on the horizon
Energy Technology Data Exchange (ETDEWEB)
The use of pressurised fluidized-bed coal combustion (fbc) in a combined cycle is seen as a most attractive technology for increasing the efficiency of electricity generation. The concept of pressurised fbc is described and the technical problems that are encountered in its operation and in limiting it to a gas turbine are discussed. Details are given of pilot plant facilities and current R and D programmes.
1982-06-01
International Nuclear Information System (INIS)
Ozone formation by a pulse positive corona discharge generated in the gas phase between a planar high voltage electrode made from reticulated vitreous carbon and a water surface with an immersed ground stainless steel plate electrode was investigated under various operating conditions. The effects of gas flow rate (0.5-3 litre min"-"1), discharge gap spacing (2.5-10 mm), applied input power (2-45 W) and gas composition (oxygen containing argon or nitrogen) on ozone production were determined. Ozone concentration increased with increasing power input and with increasing discharge gap. The production of ozone was significantly affected by the presence of water vapour formed through vaporization of water at the gas-liquid interface by the action of the gas phase discharge. The highest energy efficiency for ozone production was obtained using high voltage pulses of ...
2005-02-07
PFB coal fired combined cycle development program: commercial plant economic analysis (Task 1. 6)
Energy Technology Data Exchange (ETDEWEB)
The objectives of this program are to evaluate the Coal Fired Combined Cycle (CFCC) power plant conceptual design and to conduct supporting development programs for pressurized fluidized bed technology advancement in combustion/steam generator, gas turbine and hot gas cleanup technologies. The Coal-Fired Combined Cycle is the unique power plant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined-cycle power plant. The advantages of the combined cycle for higher efficiency and the potential of the pressurized fluidized bed combustor improvements in emissions could offer a new and attractive option to the electric utility industry. The CFCC approach provides for cooling the fluid bed combustor through the use of steam tubes in the bed which supply a steam turbine ...
1980-11-01
Sulzer RTA dual-fuel engine - natural gas instead of diesel oil
Energy Technology Data Exchange (ETDEWEB)
Testbed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited, Switzerland and its Japanese licensees Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), Nippon Kokan KK (NKK) and Sumitomo Heavy Industries Ltd. (SHI). Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited or for the generation of electricity in stationary plants, the RTA dual-fuel engine is an economic and reliable alternative to the steam or gas turbines.
1987-06-01
RTA dual-fuel engine - natural gas instead of diesel oil
Energy Technology Data Exchange (ETDEWEB)
Test bed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine-type, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited and its Japanese licenses. Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited for the generation of electricity in stationary plants, the RTA dual-fuel engines is an economic and reliable alternative to the steam or gas turbine. The performance of the engine is discussed.
1987-01-01
Gas turbine tops 40% efficiency; features novel inlet-air cooler
Energy Technology Data Exchange (ETDEWEB)
This article reports on the world's first gas turbine to top 40% thermal efficiency in simple cycle and is now operating commercially as part of a natural-gas-fired combined-cycle cogeneration (CC) plant serving the Ottawa Health Sciences Center, Ottawa, Ont, Canada. Owned and operated by TransAlta Energy Corp, Calgary, Alta, the CC plant supplies steam and hot and chilled water to the health center and another thermal user while the electricity is sold to Ontario Hydro. Part of the project included the conversion of 15-psig steam-carrying equipment to hot-water service. Commercial success of this installation heralds a new era in the application of efficient gas turbines for power generation.
1993-02-01
British Library Electronic Table of Contents (United Kingdom)
This work deals with a new route to modify polymer blend morphology in order to improve the porosity of gas diffusion layers (GDLs) for proton exchange membrane fuel cells (PEMFCs). First, electrically conductive polymer-based blends were carefully formulated using a twin-screw extrusion process. Blend electrical conductivity was ensured by the addition of high specific surface area carbon black and synthetic graphite flakes. Final GDL porosity, in particular its macroporosity, was generated by melt blending polyamide 11 (PA11) matrix with polystyrene (PS) followed by PS extraction with tetrahydrofuran (THF) solvent at room temperature. In order to improve GDL porosity by the optimisation of PS dispersion in the PA11 matrix, PA11/PS blends were compatibilised by the addition of 2 wt.-% of ...
2007-01-01
Energy Technology Data Exchange (ETDEWEB)
Operation and maintenance cost estimating methodologies for advanced coal-fired atmospheric circulating fluidized-bed and advanced natural gas-fired combined cycle electric power plants are presented. The purpose of these cost estimating relationships is for use in long range planning and evaluation of the economics of use of these technologies for electric power generation. Projected annual costs of reference plants at ten different sites in the United States, one in each of the ten DOE regions, are given as of 1989, and comparisons are made with existing technologies. A listing of a computer program implementing the methodologies is included. 14 refs., 4 figs., 13 tabs.
1989-12-01
Energy Technology Data Exchange (ETDEWEB)
An investigation of current dual-fuel natural gas/diesel engine design, performance, and emissions was conducted. The most pressing technological problems associated with dual-fuel engine use were identified along with potential solutions. It was concluded that dual-fuel engines can achieve low NOx and particulate emissions while retaining fuel-efficiency and BMEP levels comparable to those of diesel engines. The investigation also examined the potential economic impact of dual-fuel engines in diesel-electric locomotives, marine vessels, farm equipment, construction, mining, and industrial equipment, and stand-alone electricity generation systems. Recommendations for further additional funding to support research, development, and demonstration in these applications were then presented.
1994-11-01
Technoeconomic assessment of biomass to energy
International Nuclear Information System (INIS)
A spreadsheet-based decision support system has been developed that allows easy evaluation of integrated biomass to electricity and biomass to ethanol systems. The Bioenergy Assessment Model (BEAM) has been developed to allow the techno-economic assessment of biomass to electricity and biomass to ethanol schemes, including investigation of the interfacing issues. Technical and economic parameters can be assessed for a variety of feedstocks, conversion technologies and generating cycles. Production modules are currently available for biomass supply from short rotation coppice and conventional forestry relevant to conditions and practices in NW Europe. The biomass conversion modules include pre-treatment (reception, storage, handling, comminution, screening and drying); atmospheric gasification (generic gasifier, wet gas scrubbing, dual fuel engine); pressure gasification (generic gasifier, hot ...
1995-03-23
Electric utility engineer`s FGD manual -- Volume 1: FGD process design. Final report
Energy Technology Data Exchange (ETDEWEB)
Part 1 of the Electric Utility Engineer`s Flue Gas Desulfurization (FGD) Manual emphasizes the chemical and physical processes that form the basis for design and operation of lime- and limestone-based FGD systems applied to coal- or oil-fired steam electric generating stations. The objectives of Part 1 are: to provide a description of the chemical and physical design basis for lime- and limestone-based wet FGD systems; to identify and discuss the various process design parameters and process options that must be considered in developing a specification for a new FGD system; and to provide utility engineers with process knowledge useful for operating and optimizing a lime- or limestone-based wet FGD system.
1996-03-04
Energy Technology Data Exchange (ETDEWEB)
This paper describes potentials on fuel economy and NO{sub x} exhaust emissions of a series hybrid urban bus system equipped with a ceramic gas turbine engine (CGT). The simulating program developed in-house was used to analyze influences of several parameters of each main components of the hybrid vehicle system on the performance of the bus running on the modified bus driving cycle. The basic data used in this analysis for a CGT was derived from the results of 'the Automotive 100kW CGT Project' of Japan. A dynamic response of a CGT-Generator rotating system was very much improved by introducing of 'Assisting system' in which the generator was used as an acceleration-deceleration assisting device when much acceleration or deceleration was needed. This system would make a CGT operate along the optimum operating line (fuel minimum line) even under the unsteady driving conditions. This ...
2000-03-20
Economic comparison of clean coal generating technologies with natural gas-combined cycle systems
International Nuclear Information System (INIS)
This paper reports that there are four combustion technologies upon which U.S. electric utilities are expected to rely for the majority of their future power generating needs. These technologies are pulverized coal- fired combustion (PC); coal-fired fluidized bed combustion (AFBC); coal gasification, combined cycle systems (CGCC); and natural gas-fired combined cycle systems (NGCC). The engineering and economic parameters which affect the choice of a technology include capital costs, operating and maintenance costs, fuel costs, construction schedule, process risk, environmental and site impacts, fuel efficiency and flexibility, plant availability, capacity factors, timing of startup, and the importance of utility economic and financial factors.
1990-04-23
New technology for the comprehensive utilization of Chinese oil shale resources
Energy Technology Data Exchange (ETDEWEB)
In China, the conventional utilization of oil shale is concentrated mainly on retorting oil shale to produce shale oil and fuel gas, and burning oil shale to generate electricity. The growth of petroleum price, and the development in heavy industry, make these conventional utilization facilities become unavailable on the energy market. In this paper, a new comprehensive utilization system is recommended for the future use of Huadian oil shale, based on the current status of energy and the characteristics of oil shale. The system involves three subsystems: retort subsystem, where coarse oil shale (8-80 mm) is retorted to shale oil, hydrocarbon gases and oil shale semicoke; combustion subsystem, where the mixture fuel of oil-shale semicoke and fine oil shale (0-8 mm) is fed to a circulating fluidized bed (CFB) furnace to burn, in order to generate high-pressure steam which is used to supply heat and ...
2007-05-15
Energy Technology Data Exchange (ETDEWEB)
A wider use of renewable energy sources is considered to be the solution to fossil fuel depletion and environmental pollution. This paper discusses various design considerations for line focussing technology to achieve high efficiency and the possibility of generating power in the megawatt range based on solar thermal technologies. The impacts on the environment of conventional thermal power plants is outlined and an estimate made of the cost of pollution abatement measures. A cost benefit analysis is made using a typical 200 megawatt solar thermal plant, 500 km from the load centre, compared with a 220 megawatt coal fired and a similar capacity gas fired power plant, as examples. The results indicated that the energy from the solar thermal power plant is almost twice as expensive compared to conventionally generated electricity. If, however, impacts on the environment and notional cost associated with ...
1995-12-31
Energy Technology Data Exchange (ETDEWEB)
A wider use of renewable energy sources is considered to be the solution to fossil fuel depletion and environmental pollution. This paper discusses various design considerations for line focussing technology to achieve high efficiency and the possibility of generating power in the megawatt range based on solar thermal technologies. The impacts on the environment of conventional thermal power plants is outlined and an estimate made of the cost of pollution abatement measures. A cost benefit analysis is made using a typical 200 megawatt solar thermal plant, 500 km from the load centre, compared with a 220 megawatt coal fired and a similar capacity gas fired power plant, as examples. The results indicated that the energy from the solar thermal power plant is almost twice as expensive compared to conventionally generated electricity. If, however, impacts on the environment and notional cost associated with ...
1995-12-31
Gas Storage Technology Consortium
Energy Technology Data Exchange (ETDEWEB)
Gas storage is a critical element in the natural gas industry. Producers, transmission and distribution companies, marketers, and end users all benefit directly from the load balancing function of storage. The unbundling process has fundamentally changed the way storage is used and valued. As an unbundled service, the value of storage is being recovered at rates that reflect its value. Moreover, the marketplace has differentiated between various types of storage services and has increasingly rewarded flexibility, safety, and reliability. The size of the natural gas market has increased and is projected to continue to increase towards 30 trillion cubic feet over the next 10 to 15 years. Much of this increase is projected to come from electric generation, particularly peaking units. Gas storage, particularly the flexible services that are most suited to ...
2007-06-30
Natural gas implementation in Turkey. Part 1: Turkey's natural gas demand and supplies
International Nuclear Information System (INIS)
The main objective of the present study is to investigate Turkey's natural gas (NG) demand and supplies by giving the structure of the Turkish gas industry, NG pricing policy, and NG agreements. Turkey began to import NG from Russia in 1987 under a contract that provided for the delivery of 6 billion cubic meters annually (Bcma) for 25 years. The first contract, signed in 1988, stipulates delivery of 2 Bcma over a 20-yr period. The build-up of the Turkish gas market started by introducing gas in power generation in 1987 and in fertilizer production in 1988. Later contracts provide for total imports of 4 Bcma from the late 1990s. NG sales started at 0.5 Bcm in 1987 and reached to around 16 Bcm in 2001. Turkish NG demand is projected to increase extremely rapidly in coming years, with the prime consumers expected to be NG-fired electric power plants and industrial ...
2004-02-01
Combined cycle power plant with integrated low temperature heat (LOTHECO)
International Nuclear Information System (INIS)
The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) ...
2004-08-01
Large turbine, central power generation on offshore production facilities
Energy Technology Data Exchange (ETDEWEB)
A case study of a hypothetical offshore production fixed leg platform facility is presented. The purpose of the case study is to demonstrate the advantages offered by modern, fuel efficient large gas turbines in central power generation service for offshore production. The case study was presented using the Rolls- Royce RB211 large gas turbine with facility production of approximately 240,000 BPD of oil and 540 MMSCFD of associated gas. The gas was subjected to three stages of separation for removal of hydrocarbon liquids and water. The liquids, natural gas, and crude oil were exported from the production platform to an onshore receiving terminal. Gas compression is the service that requires the greatest amount of power for any given production facility. For this case study, gas compression represented approximately 70 ...
2005-07-01
Energy Technology Data Exchange (ETDEWEB)
Study was made on the city bus driven by the series hybrid system composed of a small ceramic gas turbine (100kW), generator and lead storage battery. Two driving modes were adopted, 10-driving mode and real driving mode assuming a certain bus route in Tokyo. The motor is driven mainly by generated power and additionally by battery power, however, the engine/generator system is controlled at an optimum operation point (driving mode and regenerating mode) with a maximum thermal efficiency considering depth of discharge. Design voltage of the battery had nearly no effect on fuel consumption, while its capacity as large as possible was desirable unless its weight has an adverse effect on the system. The real driving mode was lower in fuel consumption by 39% than the 10-driving mode. Since real fuel consumption is largely affected by recovery rate of regenerable energy, the operation point of the motor ...
1998-10-15
International Nuclear Information System (INIS)
Total EU (and Norway) emissions of CO_2 from thermal power generation were some 950 million tonnes in 1990, the Kyoto agreement reference level. An ongoing research project, the GESTCO project, will provide the first documentation that, for the emission sources within the selected key areas, sufficient geological storage capacity is available for at least 30 years and possibly much longer. Cost of energy will obviously increase, but it is anticipated that electricity production cost price will be comparable to that of renewables. It would further have major implications for the European power generating industry which today is totally dominated by fossil fuel combustion with enormous emissions problems. The identification and siting of subsurface CO_2 storage capability can be expected to have considerable effect on the planning for and future siting of fossil fuel plants. In Norway there are plans to build several major, ...
2001-10-01
Energy Technology Data Exchange (ETDEWEB)
The conversion of off-peak surplus electricity into peak electricity through an electrolyzer, hydrogen storage, and fuel cell energy storage system was discussed. Development efforts in high pressure alkaline electrolysis and Proton-Exchange Membrane (PEM) fuel cells have improved the near-term viability of these systems. Potential use of wind turbines and other renewable energy-based generation systems, through hydrogen-based energy storage, were discussed as a new supply of surplus electricity. An integrated set of nomographs were presented for providing quick estimates of peak electricity costs derived from an electrolyzer/hydrogen fuel cell system. The nomographs allowed first order cost comparisons of centralized versus distributed hydrogen energy systems considering trade-offs between production economies of scale and hydrogen storage and transport costs. Use of the nomographs ...
1995-06-01
Energy Technology Data Exchange (ETDEWEB)
Industrial companies are being forced by increasingly restrictive environmental legislation to implement power station technology which is environmentally compatible and which conserves scarce resources. Gas and steam turbine power stations have been causing a sensation in this field for some time. This article gives an introduction to gas and steam turbine power stations in the 4 MW to 30 MW size range. The designs of the plants described here not only provide for electricity generation by gas and steam turbines however, but also designs specific to particular companies for process steam and district heating supply. (orig.) [Deutsch] Durch immer restriktivere Umweltschutzgesetze werden die Industrieunternehmen zu einer umwelt- und ressourcenschonenden Kraftwerkstechnik gedraengt. Auf diesem Gebiet sorgen nun seit geraumer Zeit GuD-Kraftwerke fuer Furore. In diesem Beitrag werden ...
1993-12-31
The purpose of this project was to build a long-range, parallel hybrid gas/electric vehicle capable of driving beyond the communter capabilities of series hybrid vehicles. It was envisioned that since the gas engine would be able to independently propel t...
1985-01-01
Performance of spark ignited gas engine and dual fuel engine, and their application
Energy Technology Data Exchange (ETDEWEB)
This paper describes a practical knowledge on gas engine performance and combustion characteristics which are required by experimental studies for two types of developed gas burning engines, i. e. a spark ignited gas engine and a dual fuel engine, and also introduces their practical use and application. As for dual fuel engine performance, a manifold air pressure of about 27% was decreased, a scavenging ratio of 23% reduced and an exhaust temperature at the turbine inlet on 14% was increased at the gas engine operation under the mean effective cylinder pressure of 1.22 MPa in comparison with the diesel operation. Furthemore, empirical data on the effect of excess air ration on the engine performance and combustion characteristics, a risk of knocking during changing over on the dual fuel engine operation, and the rated output in case of using alternate fuel gas were reported. Two ...
1988-12-01
First-generation fuel cell demonstration and commercialization activities
International Nuclear Information System (INIS)
... electric utilities electrochemistry energy storage fuel cells organizational models
Overall analysis of the cost key factors for the nuclear energy
International Nuclear Information System (INIS)
In 1995, 25,8 % of the world electricity consumption was of nuclear origin, while in the EU this figure is increased up to 50,6 %. In order to maintain and even to increase its share in the electricity generation, Nuclear Energy needs to achieve a good economic performance as a base load source when compared with its competitors, basically coal and gas fired plants. Fossil-fired generation costs have declined over the past ten years, mainly due to lower fossil fuel prices. This factor together with the recently observed tendency of higher discount rates to be applied are challenging the attractiveness of the nuclear energy. Nuclear energy is a capital intensive option. Taken into account extensive standardization programs has been established aiming at cost reductions as well as to increase efficiency of nuclear energy utilization, among their main purposes. Externalities play an ...
1996-10-02
Use of selective catalytic reduction for control of NO{sub x} emissions from power plants
Energy Technology Data Exchange (ETDEWEB)
This report describes selective catalytic reduction (SCR) technologies which offer an economical and effective means of reducing nitrogen oxide emissions from electricity generation facilities and reviews the feasibility and cost effectiveness of employing this technology on electricity generating facilities in Ontario. Based on experiences in the United States, in British Columbia, and internationally in Japan and Germany, the indication is that the technology for the installation of SCR systems on new gas-fired combined cycle power plants and existing coal-fired power plants has grown enormously during the past decade, and has been established as the control technology of choice for nitrogen oxide emissions. It is widely acknowledged to reduce power plant nitrogen oxide emissions, and do so at a very reasonable incremental cost. It is estimated that the annualized cost of ...
1999-07-01
Energy Technology Data Exchange (ETDEWEB)
The DOE Working Group for an Assessment of Coal-Gasification Research Needs (COGARN - coal gasification advanced research needs) has reviewed and evaluated US programs dealing with coal gasification for a variety of applications. Cost evaluations and environmental-impact assessments formed important components of the deliberations. We have examined in some depth each of the following technologies: coal gasification for electricity generation in combined-cycle systems, coal gasification for the production of synthetic natural gas, coal gasifiers for direct electricity generation in fuel cells, and coal gasification for the production of synthesis gas as a first step in the manufacture of a wide variety of chemicals and fuels. Both catalytic and non-catalytic conversion processes were considered. In addition, we have constructed an orderly, long-range research ...
1987-06-01
The use of supplementary firing in an externally-fired combined cycle power plant
Energy Technology Data Exchange (ETDEWEB)
The most developed systems for the generation of electricity from coal are the Integrated coal Gasification Combined Cycle (IGCC) and the Pressurized Fluidized Bed Combustion (PFBC) system. They both represent state-of-the-art technology and provide electric power at 41-46% LHV efficiency. However, the high level of complexity leads to lower reliability and higher costs. A simpler system, based on a coal-fired steam boiler integrated with a gas turbine, has been proposed. In such a plant, known as the externally fired combined cycle (EFCC), compressed air is heated indirectly in a heat exchanger located in the coal furnace. The hot air is then expanded in a turbine, and the exhaust is passed on to the coal furnace as preheated combustion air. Steam produced in the boiler generates additional power in a steam turbine. The exclusion of coal combustion products from the ...
1997-12-31
Engineering Development of Coal-Fired High-Performance Power Systems
Energy Technology Data Exchange (ETDEWEB)
A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolysis process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is ...
2000-12-31
Energy Technology Data Exchange (ETDEWEB)
One of the five projects selected for funding within the Clean Coal Technology Program is a project proposed by the Pennsylvania Electric Company (Penelec) of Johnstown, Pennsylvania. Penelec proposes to enter into a cooperative agreement with DOE to design, construct and operate a 600 ton-per-day, 66-megawatt (MWe), coal-fueled, externally-fired combined cycle (EFCC) electric power generation facility. The EFCC is an emerging technology with promise for operating highefficiency combined gas- and steam-turbine cycles on coal. The central feature of EFCC is its coupling of the gas turbine to an external, atmospheric-pressure, coal combustor via a hightemperature ceramic heat exchanger (CerHx{reg_sign}) developed by Hague International. The EFCC technology is attractive because, unlike competing combined cycles such as Integrated Gasification (IGCC) and Pressurized Fluidized Bed ...
1994-06-01
Review of Cardiff telephone exchange total energy system after three years operation
Energy Technology Data Exchange (ETDEWEB)
A self contained continuous power generation system as described at INTELEC 1979, was successfully commissioned and put into service in a major communications centre at Cardiff in Wales. The objective was to provide all telecommunications equipment and electrical building engineering services from a dual fuel enginegenerating plant, and to recover waste heat energy to heat or cool the building. The plant, which is fully automatic, comprises five 1300kW engines using natural gas or diesel oil, and associated waste heat boiler and chiller systems. This paper reviews the functioning of the plant during its first three years of operation.
1983-10-01
International Nuclear Information System (INIS)
The proceedings include the following lectures: Facing the challenges - new structures for electricity production. Renewable energies in Europe - chances and challenges. Nuclear outlook in the UK. Sustainable energy for Europe. Requirements of the market and the grid operator at the electricity production companies. Perspectives for the future energy production. Pumped storage plants - status and perspectives. Nuclear power/renewable energies -partners or opponents? New fossil fired power stations in Europe - status and perspectives. Nuclear energy: outlook for new build and lifetime extension in Europe. Biomass in the future European energy market - experiences for dong energy. Meeting the EU 20:20 renewable energy targets: the offshore challenges. DESERTEC: sustainable electricity for Europe, Middle East and North Africa. New power plants in Europe - a challenge for project and quality management. Consideration of safely ...
2010-09-22
ENGINEERING DEVELOPMENT OF COAL-FIRED HIGH-PERFORMANCE POWER SYSTEMS
Energy Technology Data Exchange (ETDEWEB)
A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolyzation process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is ...
1998-10-01
Energy Technology Data Exchange (ETDEWEB)
A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat exergy efficiency is over 80%. (author)
2010-10-01
British Library Electronic Table of Contents (United Kingdom)
A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat e...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
It is described a process of production of celulignin from biomass through acid pre-hydrolysis in continuous reactor made of advanced materials such as niobium, titanium and monel. The celulignin is a fuel of 28.50 MJ/kg of heating power. The utilization of this technology together with eucalyptus reforestation by vegetative propagation and high efficiency thermoelectric plant (triple cycle of steam turbine, gas turbine and MHD electrical generation) allow electric power production with competitive cost when compared to hydroelectric power. (author). 1 ref. 5 figs., 2 tabs
1990-12-31
Energy Technology Data Exchange (ETDEWEB)
Developing safe, reliable, cost-effective, and efficient hydrogen-electricity co-generation systems is an important step in the quest for national energy security and minimized reliance on foreign oil. This project aimed to, through materials research, develop a cost-effective advanced technology cogenerating hydrogen and electricity directly from distributed natural gas and/or coal-derived fuels. This advanced technology was built upon a novel hybrid module composed of solid-oxide fuel-assisted electrolysis cells (SOFECs) and solid-oxide fuel cells (SOFCs), both of which were in planar, anode-supported designs. A SOFEC is an electrochemical device, in which an oxidizable fuel and steam are fed to the anode and cathode, respectively. Steam on the cathode is split into oxygen ions that are transported through an oxygen ion-conducting electrolyte (i.e. YSZ) to oxidize the anode fuel. The dissociated ...
2009-06-30
Coal quality engineering analysis aids plant performance
Energy Technology Data Exchange (ETDEWEB)
The Coal Quality Engineering Analysis (CQEA) program developed by the New York State Electric and Gas Company (NYSEC) calculates the as-burned cost of burning a specific coal in a specific generation unit. These costs include: maintenance costs for coal and ash handling equipment; ash disposal costs; cost of oil (if required for flame stability and/or derating because of pulverizer capacity limitation); flue gas desulfurization costs; cost of replacement power caused by pulverizer, precipitator fly ash collection and bottom ash capacity limitation; boiler losses due to moisture, hydrogen, dry gas and unburned carbon; power for coal and ash handling equipment; power for coal pulverizers; cost of using excess air to prevent slagging of coal with low ash softening temperatures; and effect of heat rate on coal tonnage required for a desired generation. The use of ...
1988-10-01
Simulation of the New York Power Pool for dispatcher training
This paper describes the simulation of the operating environment of the New York Power Pool (NYPP) within the Dispatcher Training Simulator facility at the New York State Electric and Gas Corporation (NYSEG). The NYSEG control center uses real-time data received from the NYPP control center to control its internal generation. In addition, the NYSEG dispatchers work very closely with the NYPP dispatchers. The exact emulation of the Generation Control functions of the NYPP EMS, and the associated data exchange with the NYSEG ECS, contribute greatly to the high degree of realism achieved in the NYSEG DTS facility. The accuracy of the power system simulation in the DTS has been validated against actual power system disturbances recorded at NYSEG.
1994-11-01
Gasification of waste from furniture industries for generation of sustainable energy
Energy Technology Data Exchange (ETDEWEB)
The global interest in renewable energy is attributed to the decline in fossil fuel sources and the need for technical, economic, social and environmental sustainability. This study focused on the new techniques that have been developed for the use of biomass for energy from wood wastes from the forest-based industry. As an energy source, wood waste contributes positively to the environment by reducing environmental problems related to contamination of soil, air and water through improper disposal of waste. Biomass gasification has the advantage of converting biomass into a combustible gas that can be used for heat generation, electricity and synthesis of chemicals. Syngas produced from gasification of eucalyptus residues has significant potential, with an average High Heating Value of 6.60 MJ/m{sup 3}, and regular composition during the process, with predominance of carbon monoxide, followed by hydrogen, carbon dioxide and ...
2010-07-01
Clean combustion of solid fuels
International Nuclear Information System (INIS)
A chemical-looping process is proposed for the clean combustion of solid fuels for electric power or heat generation. The process is based on coal gasification with CO_2 to produce CO. The CO then reduces CaSO_4, which is used as an oxygen carrier, in a separate reactor to give CaS and CO_2. A portion of the CO_2 is recycled for the gasification stage and the rest can be sent for sequestration. The CaS is sent to another reactor for oxidation with air and to generate heat or power. The overall thermal effect is the same as direct combustion, but separation of CO_2 and other pollutants, such as sulphur, is achieved. In comparison with conventional chemical-looping combustion of natural gas, much less water is present in the CO_2 product, and hence the loss of heat energy and corrosion of the fuel-reactor system can be reduced.
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
Hybrid vehicles have two power supplies as engine and electric motor which are used most efficiently corresponding to objects respectively to attain energy-saving and low pollution. In this paper, factors concerning the fuel economy of hybrid vehicles and potential thereof are examined, and the possibility of reducing fuel cost by half is described. As possible modes of highly efficient hybrid vehicles, series hybrid vehicles (SHEV) of conventional internal combustion engine, parallel hybrid vehicles using EV in combination, series-parallel hybrid vehicles (SPHV), series type fuel cell type vehicles, ceramic engine-turbo compound power generating SPHV as well as SHEV, and ceramics gas turbine engine power generating SHEV are mentioned. 10 refs., 14 figs.
1997-09-01
PFB coal fired combined cycle development program. Annual report, July 1978-June 1979
Energy Technology Data Exchange (ETDEWEB)
The Coal Fired Combined Cycle (CFCC) is the unique powerplant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined cycle powerplant. On the basis of previous studies and confirming work under this contract, General Electric continues to believe that the CFCC approach offers important advantages over alternate approaches: higher powerplant efficiency in the combustor temperature range of interest; reduced combustor/steam generator corrosion potential, due to low fluid-bed tube temperature (as contrasted to the air in tube cycle); and increased gas turbine bucket life from improved material protection systems. The objective of this program is to evaluate the coal fired combined cycle powerplant conceptual design, and to conduct a supporting development program. The supporting development is ...
1980-05-01
Technology Roadmaps - Electric and plug-in hybrid electric vehicles (EV/PHEV)
Energy Technology Data Exchange (ETDEWEB)
The mass deployment of electric and plug-in hybrid electric vehicles (EVs and PHEVs) that rely on low greenhouse gas (GHG) emission electricity generation has great potential to significantly reduce the consumption of petroleum and other high CO2-emitting transportation fuels. The vision of the Electric and Plug-in Hybrid (EV/PHEV) Vehicles Roadmap is to achieve by 2050 the widespread adoption and use of EVs and PHEVs, which together represent more than 50% of annual LDV (light duty vehicle) sales worldwide. In addition to establishing a vision, this roadmap sets strategic goals to achieve it, and identifies the steps that need to be taken to accomplish these goals. This roadmap also outlines the roles and collaboration opportunities for different stakeholders and shows how government policy can support the overall achievement of the vision. The strategic goals ...
2011-06-15
Energy Technology Data Exchange (ETDEWEB)
The Burrard Thermal Generating Station is located at Port Moody, British Columbia, and burns natural gas to supply steam to six turbine units for generating up to 912 MW of electricity. The Burrard plant accounts for ca 8.7% of the provincial generating capability. Burrard is expected to continue to fill a vital role as a supplier of displaceable firm energy to the British Columbia Hydro system. In parallel with a renewed focus on Burrard from a system planning perspective, there have also been concerns about air pollution from the plant in the context of its possible effect on the region's air quality. To address this and other issues surrounding Burrard's future, B.C. Hydro established a project team to conduct a utilization study. The team's work focused on the role of Burrard in providing a reliable and profitable role in ...
1993-01-01
Energy Technology Data Exchange (ETDEWEB)
There is an urgent need to monitor the condition of fluid-filled taped (FFT) cables. The Dissolved-Gas Analysis (DGA) technique that has been successfully applied to power transformers holds great potential for the preventive maintenance of FFT cables. However, before this emerging technique can be properly applied to cables, a suitable fluid sampling and subsequent gas analysis method had to be developed, including the generation of both laboratory and field data to aid in data interpretation. Data on gas saturation levels in various cable fluids have been presented. This paper describes a novel method developed specifically for FFT cables and discusses field results so obtained. The type, distribution and concentration of gases from fluid alone and paper alone under electrical stress has been presented, including the differences between normal and not-so-normal cable systems as ...
1994-12-31
Impact of low-rank coal properties on advanced power systems
Energy Technology Data Exchange (ETDEWEB)
Advanced coal-fired combined-cycle power systems under development and demonstration have the potential to increase generating efficiency to approach 50%, reduce the cost of electricity by up to 20%, and meet stringent standards on emissions of SO{sub x}, NO{sub x}, fine particulates, and air toxic metals. Integrated gasification combined cycle, pressurized fluidized-bed combustion, and externally fired combined cycle systems rely on different high-temperature combinations of heat exchange, gas filtration, and sulfur capture to meet these requirements. The success of these systems when operated on low-rank coals depends importantly on the behavior of the ash. This paper focuses on the behavior of ash in an intermediate-scale transport gasifier coupled with a hot-gas cleanup system. The work reported is part of the overall program on hot-gas cleanup and the transport reactor ...
1996-12-31
International Nuclear Information System (INIS)
The increasing diffusion of small-scale energy systems within the distributed generation (DG) paradigm is raising the need for studying the environmental impact due to the different DG solutions in order to assess their sustainability. Addressing the environmental impact calls for building specific models for studying both local and global emissions. In this framework, the adoption of natural gas-fueled DG cogeneration technologies may provide, as a consequence of cogeneration enhanced overall energy efficiency and of natural gas relatively low carbon content, a significant reduction of global impact in terms of CO2 emissions with respect to the separate production of electricity and heat. However, a comprehensive evaluation of the DG alternatives should take into account as well the impact due to the presence of plants spread over the territory that could increase the local pollution, in particular due ...
2008-10-01
EMFs: cutting through the controversy.
UK PubMed Central (United Kingdom)
SOME SCIENTISTS ALLEGE that exposure to electric and magnetic fields generated by electric power delivery systems is responsible for certain cancers (particularly among children), reproductive dysfunction,...Full Text Available
1996-05-01
A Theoretical Solid Oxide Fuel Cell Model for Systems Controls and Stability Design
As the aviation industry moves toward higher efficiency electrical power generation, all electric
2008-01-01
Electric utilities and natural gas use
Legal aspects of using natural gas as boiler fuel for electric utilities are reviewed through one utility's challenges to the Power Plant and Industrial Fuel Use implementation. ASARCO vs. FPC, 1973, and City of Willcox vs. FPC are discussed. (PSB)
1980-11-11
International Nuclear Information System (INIS)
The proposed method to analyze the composition of the cost of electricity is based on the energy conversion processes and the destruction of the exergy through the several thermodynamic processes that comprise a combined cycle power plant. The method uses thermoeconomics to evaluate and allocate the cost of exergy throughout the processes, considering costs related to inputs and investment in equipment. Although the concept may be applied to any combined cycle or cogeneration plant, this work develops only the mathematical modeling for three-pressure heat recovery steam generator (HRSG) configurations and total condensation of the produced steam. It is possible to study any nx1 plant configuration (n sets of gas turbine and HRSGs associated to one steam turbine generator and condenser) with the developed model, assuming that every train operates identically and in steady state. The presented model was ...
2008-02-01
Bi-directional causality in California's electricity and natural-gas markets
International Nuclear Information System (INIS)
The Granger instantaneous-causality test is applied to explore the potential causal relationships between wholesale electricity and natural-gas prices in California. The test shows these relationships to be bi-directional, and reveals California's electricity and natural-gas markets to be as inextricably intertwined as casual observation and theoretical considerations would suggest they ought to be. This meshing of markets exacerbated the effects of California's natural-gas crisis on the contemporaneous electricity crisis, while concurrently the electricity crisis may have contributed to the dysfunction in the national-gas market and helped to precipitate the natural-gas crisis. The finding supports an integrated approach, as opposed to a piecemeal approach, for formulating energy policy ...
2006-10-01
Bi-directional causality in California's electricity and natural-gas markets
International Nuclear Information System (INIS)
The Granger instantaneous-causality test is applied to explore the potential causal relationships between wholesale electricity and natural-gas prices in California. The test shows these relationships to be bi-directional, and reveals California's electricity and natural-gas markets to be as inextricably intertwined as casual observation and theoretical considerations would suggest they ought to be. This meshing of markets exacerbated the effects of California's natural-gas crisis on the contemporaneous electricity crisis, while concurrently the electricity crisis may have contributed to the dysfunction in the national-gas market and helped to precipitate the natural-gas crisis. The finding supports an integrated approach, as opposed to a piecemeal approach, for formulating energy policy ...
2006-10-01
Energy Technology Data Exchange (ETDEWEB)
This patent describes an ignition system of an internal combustion engine which consists of: a permanent magnet supported by a rotary member of the engine adapted to rotate in synchronism with a rotary shaft of the engine; a generating coil for generating an electromotive force to produce an electric current as the permanent magnet acts on the generating coil during the rotation of the rotary member; an ignition capacitor charged by the electric current generated by the generating coil; a thyristor caused to turn on by a counter electromotive force generated by the generating coil to thereby cause the ignition capacitor to begin to discharge; and an ignition coil generating a high voltage as the ignition capacitor begins to discharge, to cause a spark discharge to take place in ...
1986-09-16
Financial statistics of major US publicly owned electric utilities 1994
Energy Technology Data Exchange (ETDEWEB)
This publication presents 5 years (1990--94) of summary financial data and current year detailed financial data on the major publicly owned electric utilities. Generator and nongenerator summaries are presented. Composite tables present: Aggregates of income statement and balance sheet data, financial indicators, electric operation and maintenance expenses, electric utility plant, number of consumers, sales of electricity, and operating revenue, and electric energy account data.
1995-12-15
Energy Technology Data Exchange (ETDEWEB)
This work deals with a new route to modify polymer blend morphology in order to improve the porosity of gas diffusion layers (GDLs) for proton exchange membrane fuel cells (PEMFCs). First, electrically conductive polymer-based blends were carefully formulated using a twin-screw extrusion process. Blend electrical conductivity was ensured by the addition of high specific surface area carbon black and synthetic graphite flakes. Final GDL porosity, in particular its macroporosity, was generated by melt blending polyamide 11 (PA11) matrix with polystyrene (PS) followed by PS extraction with tetrahydrofuran (THF) solvent at room temperature. In order to improve GDL porosity by the optimisation of PS dispersion in the PA11 matrix, PA11/PS blends were compatibilised by the addition of 2 wt.-% of clay. It was observed that both macroporosity and pore size distribution were beneficially modified after blend ...
2007-12-15
Tests with cleaned and uncleaned gas on a pilot plant. Final report
Energy Technology Data Exchange (ETDEWEB)
The possibilities for heat recovery in a cast iron melting furnace were studied. A cupola furnace which produces 40 tonnes steel per hour, produces 25,000 Nm/sup 3//h of flue gases which contain 16-22% CO. Taking into account the heat losses at the chimney where fumes are cooled to 200/sup 0/C the recoverable heat is about 12.4-10/sup 6/ kcal/h which mainly consists of combustion heat in CO. This study showed that the heat can be used for the production of electricity, which will be used in the plant. Recovery of 87 kWh of electricity per tonne of steel produced is possible. A steam turbine driven generator of 3.5 MW will be required. The combustion of the low calorific gas (approximately 400 kcal/Nm/sup 3/) has been studied and gave positive results: wet CO gas can be burnt without addition of methane and preheating of air is not required. The pilot plant consisting of a thermic ...
1986-01-01
Energy Technology Data Exchange (ETDEWEB)
This report prepared for the Swiss Federal Office of Energy (SFOE) describes the practical realisation and testing of a heat recovery system based on a one-stage organic Rankine cycle with R134a as the working fluid. The waste heat has a temperature of 95 {sup o}C and originates from a gas engine that powers a small co-generation plant fuelled with biogas produced on-site. Two similar cycles have been built, ORC1 with one and ORC2 with two turbines. Only ORC1 has been tested so far. The maximum efficiency measured in these tests was 6.64% (theoretical Carnot-efficiency: 17 %) and the electric power output was 5.0 kW. The problems encountered during commissioning are described and recommendations for further improvements are given.
2005-07-01
Comparison of advanced engines for parabolic dish solar thermal power plants
A paraboloidal dish solar thermal power plant produces electrical energy by a two-step conversion process. The collector subsystem is composed of a two-axis tracking paraboloidal concentrator and a cavity receiver. The concentrator focuses intercepted sunlight (direct, normal insolation) into a cavity receiver whose aperture encircles the focal point of the concentrator. At the internal wall of the receiver the electromagnetic radiation is converted to thermal energy. A heat engine/generator assembly, which is mounted directly behind th receiver, then converts the thermal energy captured by the receiver to electricity. Developmental activity has been concentrated on relatively small power modules which employ 11- to 12-m-diam dishes to generate nominal power levels of approximately 20 kW. A comparison of advanced heat engines for use on the dish power module is presented in terms of the performance ...
1982-09-01
Energy Technology Data Exchange (ETDEWEB)
Use of gas-fired combined-cycle technology (GFCC) in the electric-utility sector could play an important role in a least-cost planning strategy and thereby provide significant benefits to the utilities and their customers. Potential benefits include reduced capital and operating costs, more-effective matching of load growth and capacity additions, greater system reliability, and reduced environmental emissions. GFCC technology was examined in eight utility systems in six geographic regions to estimate the potential benefits of its use. In all systems, GFCC technology was shown to have the potential to reduce the cumulative capital costs for adding new capacity. The overall conclusion of the study is that GFCC technology offers the potential for significant savings in many regions of the United States and that these benefits would appear over a wide range of economic conditions. The study provides insight into the important technological and ...
1988-03-01
Fuel cycle options and sustainability for new nuclear build in the UK
International Nuclear Information System (INIS)
After a long period of stagnation in the UK, Europe and the USA, there is now a real expectation that new nuclear plants will be under construction shortly. Several factors have contributed to this change of position in the UK: the growing realisation that effective action is needed to offset greenhouse gas emissions; higher prices for fossil fuels; increasing reliance on overseas supplies of oil and gas; the limitations of wind and wave power and distribution; security of supply; the gradual realisation in the deregulated electricity generation market that nuclear power is competitive and the pending closure of most of the UK's nuclear fleet within less than 15 years. All these factors have led to a reversal of the UK Government's attitude to nuclear power, which has now ruled in favour of allowing a new generation of nuclear plants being built. This paper summarises some of the ...
2008-09-14
Developing, financing and managing merchant (independent) power plants
Energy Technology Data Exchange (ETDEWEB)
Deregulation and restructuring changes in the electric power industry have provided opportunities to build new power plants. These power plants, however, will not enjoy long-term power purchase agreements with the utilities they serve, but will have to respond to the market. This is where the term `merchant plant` originates. Calpine Corp. presented its reasons for believing that now is the best time to be building new merchant plants based on modern natural gas-fired, combined-cycle power plants. Among those reasons are: (1) construction of new nuclear power plants has been rejected by people on both sides of the border, (2) attempts to promote alternative energy sources such as solar, wind and biomass have not added significant generation capacity and are not likely to do so in the near future because of their high cost, and (3) coal-fired plants are also facing environmental challenges. For all these reasons, modern ...
1998-08-01
International Nuclear Information System (INIS)
The authors report on observations of plasma wave turbulence generated during electron beam injections, spacecraft potential variations, and neutral gas emissions of the CHARGE 2 sounding rocket experiment. The payload was flown in a mother/daughter configuration, with the two sub-payloads electrically connected by an insulated, conducting tether. While tethered, the two platforms were separated, drifting apart in a direction perpendicular to both the magnetic field and to the spacecraft velocity, reaching a maximum distance of 426 m at the end of the flight. The mother carried a high-voltage (HV) system (0-460 V), biasing the mother negative relative to the daughter. The operation of the HV bias system simulated the motional emf induced in larger orbiting space structures like the Tethered Satellite System 1 (TSS 1) space shuttle mission scheduled for the spring of 1992. In addition, the mother carried an electron beam ...
Gas-temperature-dependent generation of cryoplasma jet under atmospheric pressure
International Nuclear Information System (INIS)
Plasma with a gas temperature below room temperature is not yet fully understood although it is expected to be an attractive tool for applications to material processing. In the present work, gas-temperature-dependent generation of a cryoplasma jet was studied. So far, we have generated a helium cryoplasma jet (296-5 K) under atmospheric pressure. At gas temperatures below 20 K, the helium excimer, He2, was observed clearly from by optical emission spectroscopy.
2008-09-08
Electric power monthly, July 1995 - with data for April 1995
Energy Technology Data Exchange (ETDEWEB)
This publication provides statistical data on net generation, fuel consumption, fossil fuel stocks, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on fossil fuel stocks and costs are also included.
1995-07-01
Energy Technology Data Exchange (ETDEWEB)
Some general topical information (generating capacity and electric power generation, development and structure of electric power consumption, frequency and peak load, exchange of electricity) is followed by an account of the situation of coal-fired power plants, hydroelectric power plants and nuclear power plants, and a brief discussion of the environmental situation (emissions and wastes, immissions, and air pollution abatement measures for power plants). (orig./UA).
1992-11-02
U.S. energy policy and the Bush administration's North American energy strategy
Energy Technology Data Exchange (ETDEWEB)
This presentation outlined the energy policy in the United States and its impact on frontier development in Alaska, deepwater offshore fields and in the western oil shale resources. The energy strategy focuses on technologies that increase domestic production from existing resources as well as technologies that create new sources of energy. In addition to emphasizing the cooperation between Canada and the United States in ensuring energy supply security and stability, this paper discussed the importance of overall bilateral trade between the 2 countries. It was noted that Canada is the United State's most secure and reliable energy partner and is the number 1 supplier of imported oil, natural gas, electricity and uranium. The Bush administration's energy policy is based on the mandate to supply stable, reliable, secure, affordable and environmentally sound energy for the country's growing economy. The energy strategy ...
2005-07-01
Energy Technology Data Exchange (ETDEWEB)
A shock wave appears when the release of accumulated energy is instantaneous. For instance, it accompanies gunpowder explosion, electric discharge, laser beam convergence, collision of high-speed objects, release of high-pressure gas, and supersonic flight. The shock wave research center of Institute of Fluid Science, Tohoku University, is engaged in researches to elucidate the basics of various shock wave phenomena and to apply the fruit to engineering, science, and medicine. In this report, some examples of recent application studies at the center are described, and the trend of shock wave researches in the future is introduced. The ultimate state of the stagnation point of a nozzle flow simulating a reentry into the atmosphere is produced by shock wave compression in a free piston shock tube which is a ground-borne experimental apparatus. Los Alamos National Laboratory, U.S., succeeded in generating metallic hydrogen of ...
1999-03-15
International Nuclear Information System (INIS)
A high-performance power system (HIPPS) is being developed. This system is a coal-fired, combined-cycle plant that will have an efficiency of at least 47 percent, based on the higher heating value of the fuel. The original emissions goal of the project was for NOx and SOx to each be below 0.15 lb/MMBtu. In the Phase 2 RFP this emissions goal was reduced to 0.06 lb/MMBtu. The ultimate goal of HIPPS is to have an all-coal-fueled system, but initial versions of the system are allowed up to 35 percent heat input from natural gas. Foster Wheeler Development Corporation is currently leading a team effort with AlliedSignal, Bechtel, Foster Wheeler Energy Corporation, Research-Cottrell, TRW and Westinghouse. Previous work on the project was also done by General Electric. The HIPPS plant will use a high-Temperature Advanced Furnace (HITAF) to achieve combined-cycle operation with coal as the primary fuel. The HITAF is an atmospheric-pressure, ...
1995-07-12
Energy Technology Data Exchange (ETDEWEB)
The Externally-Fired Combined Cycle (EFCC) is an attractive emerging technology for powering high efficiency combined gas and steam turbine cycles with coal or other ash bearing fuels. In the EFCC, the heat input to a gas turbine is supplied indirectly through a ceramic air heater. The air heater, along with an atmospheric coal combustor and ancillary equipment, replaces the conventional gas turbine combustor. A steam generator located downstream from the ceramic air heater and steam turbine cycle, along with an exhaust cleanup system, completes the combined cycle. A key element of the EFCC Development Program, the 25 MMBtu/h heat-input Kennebunk Test Facility (KTF), has recently begun operation. The KTF has been operating with natural gas and will begin operating with coal in early 1995. The US Department of Energy selected an EFCC repowering of the Pennsylvania ...
1995-06-01
International Nuclear Information System (INIS)
A one-dimensional numerical model for the expansion of impact-produced vapor clouds is used to investigate magnetic field generation mechanisms in events such as meteor collisions with the moon. The resulting cloud properties, such as ionization fraction, electrical conductivity, radial expansion velocity, mass density, and energy density are estimated. The model is initiated with the peak shock states and pressure thresholds for incipient and complete vaporization of anorthosite lunar surface materials by iron and GA composition meteorites. The expansion of the spherical gas cloud into a vacuum was traced with a one-dimensional explicit lagrangian hydrodynamic code. The hypervelocity impact plasmas produced are found to be significant in the amplitudes and orientations of the magnetic fields generated. An ambient magnetic field could have been provided by the core dynamo, which would have interacted ...
1984-03-12
GREENHOUSE GAS EMISSIONS CONTROL BY OXYGEN FIRING IN CIRCULATING FLUIDIZED BED BOILERS
Energy Technology Data Exchange (ETDEWEB)
Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this study, ALSTOM Power Inc. (ALSTOM) has investigated several coal fired power plant configurations designed to capture CO{sub 2} from effluent gas streams for use or sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). ...
2003-05-15
Electric power monthly, June 1995 with data for March 1995
Energy Technology Data Exchange (ETDEWEB)
The Coal and Electric Data and Renewables Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy prepares the EPM. This publication provides monthly statistics at the State, Census division, and US levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. The EIA publishes statistics in the EPM on net generation by energy source; consumption, stocks, quantity, quality, and cost of fossil fuels; and capability of new ...
1995-06-19
Electric power monthly with data for October 1995
Energy Technology Data Exchange (ETDEWEB)
The Coal and Electric Data and Renewables Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy prepares the EPM. This publication provides monthly statistics at the State, Census division, and U.S. levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North American Electric Reliability Council (NERC) regions. The EIA publishes statistics in the EPM on net generation by energy source; consumption, stocks, quantity, quality, and cost of fossil fuels; and capability of new ...
1996-01-01
Energy Technology Data Exchange (ETDEWEB)
A gas-diesel dual fuel engine apparatus is described having a diesel engine, a diesel fuel supply system including a diesel fuel injection pump, a gaseous fuel supply system including a gaseous fuel regulating valve, and a governing and controlling device for governing the speed of the engine through the control of fuel supplied to the engine and controlling the switchover of the operation of the engine between a diesel fuel mode and a gaseous fuel mode. The improvement of the governing and controlling device consists of: (a) at least one electronic governor means adapted to compare a speed signal representing the actual operating speed of the diesel engine with a set speed signal representing the set speed thereof; (b) a pair of electric actuator means having respective power amplifier circuits and mechanically connected to the diesel fuel injection pump and the gaseous fuel regulating valve, respectively, for the actuation thereof; (c) mode ...
1986-03-18
Design of a 60 MW CFB gasification system (CGAS) for Uganda : utilising rice husks as input fuel
Energy Technology Data Exchange (ETDEWEB)
In Uganda, biomass comprises more than 95 per cent of the total energy supply. Agricultural residues are a major source of energy that can be converted into producer gas in biomass gasifiers. The high poverty levels in Uganda can be attributed in part to the fact that more than 90 per cent of the population does not have access to electricity due to limited and unreliable electricity produced in the country. A circulating fluidized bed (CFB) gasification system was designed in this study in order to generate a system for the effective use of agricultural wastes for energy production. Rice husks were used as the feedstock for a power output of 60 MW. The gasification system was designed using ERGUN CFB software with available theoretical and experimental data. The design comprises a reactor subsystem, air distribution plate, cyclone, air inlet and fuel feeding systems. The reactor is 10 m high and has a ...
2010-07-01
International Nuclear Information System (INIS)
Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific.
1994-06-25
Energy from waste: current progress in Sweden
Energy Technology Data Exchange (ETDEWEB)
Considerable effort worldwide has been put into trying to find the best way to utilise the large amount of energy that we put into our dustbins every day. One of the problems encountered is that the waste collection systems tend to gather together in one place between 400 and 1000 t of the stuff everyday and since it is possible to extract rather more than 2 MW from each tonne, that is a lot of energy for which to find a market. In continental European cities, especially Germany, and Sweden with most of the population living in apartment blocks, and with colder winters than the UK, district heating provides a suitable market. With its milder winters, more diverse housing and cheap gas the UK is not such a fertile ground for district heating. But since the passing of the Energy Act in 1984, there is a steady market in electricity generation with the advantage that the purchase tariffs are published so that income can be ...
1988-11-01
Degradation of antibiotics in water by non-thermal plasma treatment.
The decomposition of three ?-lactam antibiotics (amoxicillin, oxacillin and ampicillin) in aqueous solution was investigated using a dielectric barrier discharge (DBD) in coaxial configuration. Solutions of concentration 100 mg/L were made to flow as a film over the surface of the inner electrode of the plasma reactor, so the discharge was generated at the gas-liquid interface. The electrical discharge was operated in pulsed regime, at room temperature and atmospheric pressure, in oxygen. Amoxicillin was degraded after 10 min plasma treatment, while the other two antibiotics required about 30 min for decomposition. The evolution of the degradation process was continuously followed using liquid chromatography-mass spectrometry (LC-MS), total organic carbon (TOC) and chemical oxygen demand (COD) analyses. PMID:21514950
2011-04-06
Chicken runs provide the fuel for Fibrowatt's global ambitions
Energy Technology Data Exchange (ETDEWEB)
This article reports on the operation of Fibrowatt's third chicken waste-fuelled power plant at Thetford in Norfolk, UK. Details are given of the plant which started operation in October 1998, the chicken litter fuel, the spiral screw fuel feeders, the Detroit Stoker grate and spreader stokers which ensure the fuel is burnt mid-air, the production of fertiliser from the ash, and fluegas emission control using cyclones, a baghouse and lime addition to neutralise acid gas. The economics of the project, and the support for the renewable electricity generation under the UK government's Non-Fossil Fuel Obligation are discussed. A site plan of the Thetford plant and a flow diagram of the process are provided.
2000-08-01
The case of nuclear power: an economical analysis
Energy Technology Data Exchange (ETDEWEB)
In this paper an analysis will be performed to assess the economical competitiveness of Nuclear Power against other base load technologies. There are several plans to build more nuclear power plants in western countries; these plans are result among other things of the fossil fuel high prices and the concern for the global warming. France started the construction of one EPR at Flamanville in 2007 and at the end of 2008 there were 17 applications before NRC for construction and operation licenses (COL) to build as much as 26 new reactor units in USA, among the designs selected are the US-EPR, APWR, ESBWR, ABWR and AP1000. Currently, there is a lot of uncertainty about what is the overnight cost for a new generation III nuclear power plant and the vendors are not providing too much information. However, it is expected that under the new economy conditions the overnight cost will be between 2500 and 3500 USD/kW, the output electricity power of the ...
2009-06-15
Energy Technology Data Exchange (ETDEWEB)
A common practice of electric utilities experiencing transmission and distribution (T and D) system overloads is to expand the substation, add lines, or upgrade equipment, all of which are capital intensive options. In 1988, it was hypothesized that strategically sited photovoltaics (PV) could benefit parts of T and D systems near or at overloaded conditions. An evaluation methodology was developed and applied to a test case (Kerman Substation near Fresno, California). Analytical results suggested that the value of PV to the T and D system could substantially exceed its energy and generation capacity value. The importance of this finding indicated the need for empirical validation. This led to the construction of a 0.5 MW PV demonstration plant by Pacific Gas and Electric Company (PG and E) at Kerman, California as part of the PVUSA (PV for Utility Scale Applications) project. PVUSA is a national ...
1994-07-01
Energy Technology Data Exchange (ETDEWEB)
The Clean Air Act establishes New Source Review (NSR) programs that apply to the construction or modification of major stationary emissions sources. In 2002 and 2003, the U.S. Environmental Protection Agency revised its rules to narrow the applicability of NSR to facility renovations. Congress then mandated a National Research Council study of the effects of the rules. An electricity-sector model - the Integrated Planning Model (IPM) - was used to explore the possible effects of the equipment replacement provision (ERP), the principal NSR change that was to affect the power-generation industry. The studies focused in particular on coal-fired electricity generating units, EGUs, for two reasons. First, coal-fired EGUs are important contributors of these pollutants, accounting for approximately 70 and 20% of nations SO{sub 2} and NOx emissions in 2004, respectively. Second, the shares of total capacity of ...
2007-03-15
Electric power monthly: October 1995, with data for July 1995
Energy Technology Data Exchange (ETDEWEB)
The Electric Power Monthly (EPM) presents monthly electricity statistics for a wide audience including Congress, Federal and State agencies, the electric utility industry, and the general public. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. The Coal and Electric Data and Renewables Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy prepares the EPM. This publication provides monthly statistics at the State, Census division, and US levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity sales, revenue, and average revenue per ...
1995-10-19
Grid Connections, Batteries, and On-Board Generation: Sources for Electric Traction
British Library Electronic Table of Contents (United Kingdom)
Well over 90 percent of all motorized transportation is fueled by products of petroleum, but the end of such widespread use of oil may be in sight. Among alternative fuels for land transportation, electricity appears to be the most promising, in part because it can be renewably produced and readily transmitted. The inadequacy and high cost of on-board storage of electrical energy present major challenges to widespread deployment of electric traction, and may do so for many years. On-board generation of electrical energy also presents challenges. The third means of powering electric traction is to provide for connection to the electricity grid while in motion. Grid-connected vehicles (GCVs) are an established feature of many cities and of much inter-city transportation, chiefly as electric ...
2010-01-01
Analog Gun (Selection of Consumable Cartridge Materials).
... Descriptors : *Combustible cartridge cases, *Polymers, *Test equipment, *Patents, Combustion chambers, Breech mechanisms, Gas generating ...
1975-09-02
Tidd experience prepares hot gas cleaning technology for commercialization
Energy Technology Data Exchange (ETDEWEB)
Pressurized fluidized bed combustion (PFBC) is an emerging coal-fired, combined-cycle power generation technology nearing commercial status through several operating and planned demonstration plants throughout the world. Current-generation PFBC plants use ``ruggedized`` gas turbines that can tolerate dust loading common with conventional cyclone gas cleaning. The next generation of PFBC will apply advanced hot gas cleaning systems that will reuse the dust loading to low levels acceptable to high performance, industrial gas turbines. These advances should result in performance and cost advantages. This article examines the demonstration of PFBC technology at Tidd power station.
1995-09-01
Development of a polymer fuel cell system for naval surface ship applications
Energy Technology Data Exchange (ETDEWEB)
In the framework of the development of new generations of surface ships, the Royal Netherlands Navy is studying the option of the all-electric ship concept. Background is the growing demand of electric power on board of naval ships for various services (including weapons and sensors). Important features of such an all-electric ship concept are decentralized electric energy generation and storage. In such an all-electric ship concept, fuel cells are expected to play an important role in the future, not only for reasons of energy efficiency and low emissions, but also because of their potential military advantages. Especially polymer electrolyte fuel cell systems appear to be very interesting for this application.
1996-12-31
Low temperature solar-to-electric power conversion system
An electric power generating apparatus is described, including: a solar collector; a primary thermal loop including primary thermal fluid; a cavity receiver to receive reflected solar energy from the solar reflector, convert the solar energy into thermal energy, and transmit the thermal energy to the primary thermal fluid by heating the primary thermal fluid not to exceed a given temperature, the given temperature being substantially equal to 700 F; a Stirling engine receiving the primary thermal fluid heated by the cavity receiver, including means to generate mechanical power and means to generate electrical power from the means to generate mechanical power.
1993-07-20
Energy Technology Data Exchange (ETDEWEB)
Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam- cycle is the conventional conversion method; however, total energy conversion efficiencies for this type of process are only slightly over 30{percent}. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40{percent}. Conversion processes based on gasification offer efficiencies above 50{percent}. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. Problems arise due to the corrosive nature of H{sub 2}S on metal components contained in these cycles. Because of this, H{sub 2}S concentrations must be reduced to low levels corresponding to certain power applications. An advanced process for the separation of hydrogen sulfide ...
1996-09-01
Gas turbines aim at world power market dominance
Energy Technology Data Exchange (ETDEWEB)
Rapid technology improvements, resulting in high efficiency, emissions reduction and low generation cost, are making gas turbines the generation technology of choice despite some recent reliability problems. The basic reason for the dominance is high efficiency. The rapid pace of gas-turbine technology improvement in the 1990s drove combined-cycle thermal efficiency to nearly 60 percent with natural gas as the fuel. It will probably go even higher after the year 2000. In addition, the gas-fired combined cycle is a bargain. With natural gas prices where they are right now, it is the least-cost generation operation for power producers with access to gas. Many will replace older, high-cost power plants with new gas-fired combined cycle power plants.
1996-06-01
Resistive cryogenic cable economic-viability evaluation. Final report, Volume I
Energy Technology Data Exchange (ETDEWEB)
This report presents a reassessment of the design of Resistive Cryogenic Cable Systems with regard to dielectric material selection, thermal insulation selection, conductor design, and refrigeration subsystem design. An algorithm using test data generated as part of the program and available from the literature was developed and used to assess the driving parameters for system cost analysis. The results of this cost sensitivity analysis are presented. An electric utility, Public Service Electric and Gas of New Jersey (PSE and G), performed an economic viability evaluation comparing two selected Resistive Cryogenic Cable Systems to a conventional cable system (high pressure oil-filled). The comparison was made for a 35-mile network application on the PSE and G transmission system scheduled to be placed in service in 1995. Consideration was given to equipment capital, installation, and operating costs. It ...
1980-03-31
CLEAR LIQUOR SCRUBBING WITH ANHYDRITE PRODUCTION
Energy Technology Data Exchange (ETDEWEB)
This project is funded by the US Department of Energy's Federal Energy Technology Center (DOE/FETC) under a cost-sharing PRDA with Radian International. The Electric Power Research Institute (EPRI) is providing co-funding and technical oversight. The project is part of FETC's Advanced Power Systems Program, whose mission is to accelerate the commercialization of affordable, high-efficiency, low emission, coal-fueled electric generating technologies. This project was submitted in response to Area 4 of DOE's Mega-PRDA: Advanced High-Performance SO{sub 2} Control Concepts. The goals of this research area are to develop advanced flue gas desulfurization (FGD) processes that achieve greater than 99% SO{sub 2} removal efficiency, are 25% cheaper than commercial FGD systems, and provide a valuable byproduct that will be recycled rather than disposed. Area 4 also included the ...
1998-08-01
Energy Technology Data Exchange (ETDEWEB)
The Electric Power Monthly is prepared by the Survey Management Division; Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), Department of Energy. This publication provides monthly statistics at the national, Census division, and State levels for net generation, fuel consumption, fuel stocks, quantity and quality of fuel, cost of fuel, electricity sales, revenue, and average revenue per kilowatthour of electricity sold. Data on net generation, fuel consumption, fuel stocks, quantity and cost of fuel are also displayed for the North American Electric Reliability Council (NERC) regions. Additionally, statistics by company and plant are published in the EPM on capability of new plants, new generation, fuel consumption, fuel stocks, quantity and quality of fuel, and cost of fuel.
1992-05-01
Microturbine applications for the oil and gas industries of South America
Energy Technology Data Exchange (ETDEWEB)
This paper will describe the application of power generation by the use of microturbine technology by Capstone Turbine Corporation throughout South America. The purpose of this paper is to describe the technology and the experience gained over the last six years. The microturbines are power generation systems that produce energy from a diverse range of liquid or gaseous fuels. The generator is driven by a small gas turbine with a common shaft for the rotors of the generator and the engine. (author)
2008-07-01
Electrical equipment of the Marchtrenk power station on the river Traun
Energy Technology Data Exchange (ETDEWEB)
By way of introduction, the author describes the electrical equipment of the power station on the River Traun and then lists the main features of the electrical systems such as generators, transformers, the power transmission systems as, e.g., the generator leads, the 8 kV switch plant, the 110 kV oil-filled cable as well as the station-service, control, protection and monitoring systems. The control of the headwater level and of the mechanical systems of the barrage is described in detail.
1982-03-01
Generators of nonequilibrium low-temperature plasma
Energy Technology Data Exchange (ETDEWEB)
Results are described of a study and of the characteristics of sources of a non-equilibrium gas-discharge plasma. The plasma generators considered include glow, high frequency, and arc discharge generators. Thermodynamic, ionic, and electronic processes occurring in the plasmas are evaluated.
1988-06-01
Energy Technology Data Exchange (ETDEWEB)
In the research of a more efficient, less costly, more environmentally responsible and less technically difficult method for generating electrical power from coal, `the Partially Gasified Coal Fired Combined Cycle with a CFBC with Different Speeds (DFBC)` is introduced by Tsinghua University. The high efficiency cycle includes gasification, compressed air heating in a fluidized bed immersed air heater followed by a combustor and the heat recovery of gas turbine exhausted gas used as the combustion of coal in the differential-velocity atmospheric circulating fluidized bed. Superheated steam is raised in the DFBC boiler. A preliminary analysis is made for the choice of combined cycle components. The computer program can be used to evaluate the design and off-design performance of the power plant. The simulation results show that the new system is a valuable coal fired combined cycle system for China, ...
1996-12-31
Energy Technology Data Exchange (ETDEWEB)
An approximate solution was proposed in which a sensitivity analysis by the storage and release of heat was performed for the subject issues and in which an operating method was thereby determined for the equipment constituting the system by means of a linear programming. Accordingly, a heat storage type energy supply system for a district cooling and heating was taken up as a concrete object to be examined. This system consisted of a gas turbine generator, initial power receiving equipment, gas boiler, electric heat pump for ice heat storage, cooling tower, heat exchanger, steam absorbing refrigerating machine, ice heat storage tank, cold and warm water heat storage tank, etc. As a result of comparison between the proposed method and the resolving method, the former showed -0.92 to 2.58% in the increase in the operating cost compared with the latter. A case where the operating cost of the resolving ...
1996-02-01
Rehabilitation of a gassy low pressure liquid filled 115 kV cable
Energy Technology Data Exchange (ETDEWEB)
The recent attempt to degassify a self contained liquid filled (SCLF) cable in Ontario Hydro is described. In September 1989, there was a high pressure alarm on one phase of a SCLF 115 kV cable circuit. The direct buried cable circuit is about 1,890 m long with two joints and was installed in 1968. Oil samples from the cable had 10 to 12% gas content with high levels of hydrogen, methane, and ethane, and very low levels of carbon monoxide, carbon dioxide, and acetylene. From these results it was concluded that the gas was generated by low energy electrical discharges and the paper insulation was not degraded. Various utilities and cable manufacturers were contacted to find if they had experienced similar problems. The cable duct oil was flushed and gasified and the successive oil samples were analyzed in order to locate the gassing site. The joints were examined and oil samples were taken through holes ...
1994-12-31
On appraising alternative power plant investment proposals. Pt. 1: The economic model
Energy Technology Data Exchange (ETDEWEB)
Combined energy plants operating on the Brayton-Rankine cycle have gained wide acceptance as the most efficient energy conversion system. The technology is well proven and numerous research activities are underway to develop it further past its present plateau of performance. In developed and emerging economies alike, the current situation in the global economic market has caused the liberalisation of the energy industry in some countries, and in others it is causing a rethink of economic and energy policies. A result is that electric utility companies that have enjoyed a monopoly in power generation and distribution are seeing this privilege being eroded. This is opening up opportunities for independent power production and, consequently, for gas/steam turbine plants because of the technical merits of the technology and its ability to fill the vacuum being created in the energy industry. An economic model has been ...
2000-12-01
Implementing climate wise at Johnson & Johnson
Energy Technology Data Exchange (ETDEWEB)
Johnson & Johnson has had a formal energy program since the early 1970`s. A corporate energy department was formed as a result of the disruption of energy supplies and rising energy costs. Johnson & Johnson is a decentralized company with many independent operating companies throughout the world. The corporate energy department cuts across the different levels of management to delivery energy related information to the actual implementers at all of our locations worldwide. Like many other energy programs, Johnson & Johnson`s program had highs and lows depending on worldwide energy activities. Unlike many other corporate programs that were disbanded in the late 1980`s, our program remained in place, although there was not a high level of interest or attention. In the early 1990`s, the link was made between electricity generation and greenhouse gas emissions, initially by the Green Lights program and strongly ...
1996-05-01
Energy Technology Data Exchange (ETDEWEB)
Options for successfully using biogas depend on project scale. Almost all biogas from anaerobic digesters must first go through a gas handling system that pressurizes, meters, and filters the biogas. Additional treatment, including hydrogen sulfide-mercaptan scrubbing, gas drying, and carbon dioxide removal may be necessary for specialized uses, but these are complex and expensive processes. Thus, they can be justified only for large-scale projects that require high-quality biogas. Small-scale projects (less than 65 cfm) generally use biogas (as produced) as a boiler fuel or for fueling internal combustion engine-generators to produce electricity. If engines or boilers are selected properly, there should be no need to remove hydrogen sulfide. Small-scale combustion turbines, steam turbines, and fuel cells are not used because of their technical complexity and high capital cost. Biogas cleanup to ...
1996-01-01
Electricity generation from rice husk in Indian rice mills: potential and financial viability
Energy Technology Data Exchange (ETDEWEB)
Rice husk generated as a by-product of rice processing is an important energy resource. The availability of this resource in India has been assessed and the technologies for exploitation of its energy potential in rice processing industry discussed. Nomographs have been developed for estimation of the husk required to meet the energy demand of parboiling, drying and milling operations. The unit cost of electricity using rice husk gasifier-based power generation systems has been calculated and its financial feasibility assessed in comparison with utility-supplied and diesel-generated electricity. With the cost and efficiency data assumed here, the unit cost of electricity produced by rice husk gasifier-dual fuel engine-generator system varies between Rs 2/kWh and Rs 7/kWh. (author)
1996-10-01
Electricity generation from rice husk in Indian rice mills: potential and financial viability
Energy Technology Data Exchange (ETDEWEB)
Rice husk generated as a by-product of rice processing is an important energy resource. The availability of this resource in India has been assessed and the technologies for exploitation of its energy potential in the rice processing industry discussed. Nomographs have been developed for estimation of the husk required to meet the energy of parboiling, drying and milling operations. The unit cost of electricity using rice husk gasifier-based power generation systems has been calculated and its financial feasibility assessed in comparison with utility-supplied and diesel-generated electricity. With the cost and efficiency data assumed here, the unit cost of electricity produced by rice husk gasifier-dual fuel engine-generator system varies between Rs 2/kWh and Rs 7/kWh. (35 Rs approximates to SUS 1.). (author)
1998-12-31
Standardization of rules for manufacturing normal electrical equipment for mining
Energy Technology Data Exchange (ETDEWEB)
Information is provided about standardization and unification of rules for manufacturing normal electrical equipment designed for operating in underground shafts when there is no danger of explosion of gas, dust or steam. An analysis is made of the requirements included in the CEMA standard and in the state standard.
1983-01-01
Smelting of Arseniferous Copper Concentrate in an Electric-Arc Furnace.
The Bureau of Mines and ASARCO Inc. entered a cooperative agreement to determine the feasibility of producing copper matte in an electric furnace from blends of copper concentrate similar to those currently smelted in a gas-fired reverberatory system at A...
1976-01-01
The possibility of using clean coal in Malaysia
Energy Technology Data Exchange (ETDEWEB)
The Asia-Pacific region will see tremendous growth in demand for electricity in the next few decades and will be an important market for generation equipment and associated services. The Association of Southeast Asian Nations (ASEAN) countries alone anticipate additional power demand of more than 37,000 NM by the year 2000, with an estimated total expenditure of US $85 billion. Trends in recent years show natural gas-fired combined cycle in plants to be fast gaining in popularity over conventional thermal plants. The advantages include increased primary energy conversion efficiency coupled with significant reduction in pollutant emissions, shorter construction times, faster loading rates and reduced staffing requirements. In the computer model used for generation capacity expansion planning in Tenaga Nasional Berhad, clean coal technology models are not used as candidate plants. In the opinion of the ...
1994-12-31
Highlights of design and construction of Sendai Nuclear Power Station Unit No.2
International Nuclear Information System (INIS)
As for No.2 plant in Sendai Nuclear Power Station, which is the fourth nuclear power generation facilities in Kyushu Electric Power Co., Inc., all works have been completed, and at present, the final trial operation is under way. In No.2 plant, many new techniques for raising the reliability and safety, improving the maintainability and reducing radiation exposure were introduced on the basis of the operation experience of PWRs obtained so far, similarly to No.1 plant. In this paper, the main items of the new techniques related to the design and construction of the plant are reported. No. 2 plant is a first improved and standardized plant having the thermal output of 2660 MW for standard three-loop PWRs, and the rated power output was set at 890 MW. As for the turbine, TC6F-40 in was adopted. As the improved design, a large reactor containment vessel, 17 x 17 type 9-grid fuel, improved steam generators, a reactor vessel ...
1985-01-01
Electricity supply in the United Kingdom. Brief details and statistics
Energy Technology Data Exchange (ETDEWEB)
Statistical detail is given of the electricity generation and transmission systems in the UK. Breakdown by type of station, by fuel and the proportion generated by others apart from the generating or area boards is presented. Figures are provided for the various high voltage transmission lines in terms of route and circuit length as well as the number of towers and the capacity of mains transformers.
1987-06-01
A calculation program for electricity generation costs using LOTUS
Energy Technology Data Exchange (ETDEWEB)
This program is designed in order to calculate electricity generation cost by different energy sources, and menu type is adopted for user convenience. This program also graphically shows the share of capital investment cost, O and M cost, and fuel cost. Sensitivity analysis about discount rate can also be carried out by this program, taking into consideration the important role of the discount rate in the generation costs calculation. (Author) 7 refs., 1 fig., 3 tabs.
1994-12-01
International Nuclear Information System (INIS)
German (15 Jun 1974). Switzerland Kocian, P. Ecole Polytechnique Federale,
1974-06-01
Electrically Tunable Terahertz Quantum-Cascade Lasers
Improved quantum-cascade lasers. (QCLs) are being developed as electri- ... These devices would supplant gas lasers as far-infrared sources. ...
Monthly energy review, May 1993
Energy Technology Data Exchange (ETDEWEB)
The Monthly Energy Review provides an overview of the production, distribution, and consumption of energy derived from petroleum natural gas, coal, electricity, and nuclear energy. It also discusses oil and gas resource development, energy prices, and issues relevant to international energy markets.
1993-05-01
Pricing electricity for sustainability : climate change and Canada's electricity sector
International Nuclear Information System (INIS)
The electricity sector is Canada's largest single source of greenhouse gas (GHG) emissions. This paper discussed electricity and carbon pricing approaches to reducing GHG emissions in the electricity sector. An overview of the links between electricity pricing and climate change was presented, and current and emerging trends in electricity pricing related to encouraging energy conservation were reviewed. Market prices and failures were discussed. Approaches to pricing electricity included an increase in block prices; time-of-use prices; demand-side management and energy efficiency; and carbon pricing in Canada and electricity pricing signals. The study showed that several provincial utilities in Canada are experimenting with market-based pricing approaches for electricity and carbon that may help to ...
Pricing electricity for sustainability : climate change and Canada's electricity sector
Energy Technology Data Exchange (ETDEWEB)
The electricity sector is Canada's largest single source of greenhouse gas (GHG) emissions. This paper discussed electricity and carbon pricing approaches to reducing GHG emissions in the electricity sector. An overview of the links between electricity pricing and climate change was presented, and current and emerging trends in electricity pricing related to encouraging energy conservation were reviewed. Market prices and failures were discussed. Approaches to pricing electricity included an increase in block prices; time-of-use prices; demand-side management and energy efficiency; and carbon pricing in Canada and electricity pricing signals. The study showed that several provincial utilities in Canada are experimenting with market-based pricing approaches for electricity and carbon that may ...
2010-01-15
Options available and perceived constraints to implementation
Energy Technology Data Exchange (ETDEWEB)
The economics of renewable energy technologies when deployed in a decentralised manner are more favourable than the simple cost of the fossil fuel generated electricity displaced. They have capital and maintenance cost savings associated with the electrical transmission in infrastructures which are avoided. Worked examples are presented. (UK)
1995-12-31
Harnessing the geothermal resources of sedimentary basins for electricity production
Use of geothermal resources for generating electricity is briefly analyzed. Results obtained from optimization of the thermodynamic cycle implemented in the secondary coolant circuit of a binary geothermal power station and the parameters of its primary heat carrier circuit are presented.
2011-02-01
Energy Technology Data Exchange (ETDEWEB)
The report deals with the energy consumption of traffic and its emissions of hazardous substances into the air, and stresses the advantages of the electric car with respect to energy consumption and noise generation. 5 figs., 3 refs.
1991-01-01
Electric power monthly, December 1997 with data for September 1997
Energy Technology Data Exchange (ETDEWEB)
The Electric Power Monthly (EPM) presents monthly electricity statistics for a wide audience including congress, Federal and State agencies, the electric utility industry, and the general public. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. This publication provides monthly statistics at the State, Census division, and US levels for net generation, fossil fuel consumption and stocks, quantity and quality of fossil fuels, cost of fossil fuels, electricity retail sales, associated revenue, and average revenue per kilowatthour of electricity sold. In addition, data on net generation, fuel consumption, fuel stocks, quantity and cost of fossil fuels are also displayed for the North ...
1997-12-01
Report of study group 7.1: natural gas in competition with electric power in industrial applications
Energy Technology Data Exchange (ETDEWEB)
This report consists of three sections. The first section is a brief general overview of all the issues that impact the competition between natural gas and electricity in industrial applications. The second section of this report focus on the all the marketing issues and provides detail analysis of the status of these issues in Europe, Japan and United States. The third section of this report is a detail review of the current status of the competition between gas technologies and electro-technologies, it also make recommendation for developing new gas technologies. The fourth section is a contribution from M. Pettersson and S. Stenstroem, Sweden, on infrared dryers. (authors)
2000-07-01
Allocation of risks in a competitive electric market
Energy Technology Data Exchange (ETDEWEB)
To many, recent developments in electric markets are perplexing. Competition has appeared, often in the form of new players who do not own and operate generation or transmission facilities. Yet, these players happily enter into contracts obliging them to make or take delivery of power at set prices for months or even years into the future. They seem unconcerned about predicted capacity shortages, fuel price uncertainty or unpredictable plant outages. For the most part, these new players understand these risks quite well. They simply believe in the efficacy of markets. Until recently, price ensured recovery of cost. They foresee a true market where price makes supply equal demand and cost is not a factor in the short term at least. The appearance of such players is an augury of the new industry structure, one in which specialists in taking and managing distinct business risks evolve from within or enter from outside. They take and manage price ...
1996-03-01
Emissions trading and green power : profitability for buyers and sellers
Energy Technology Data Exchange (ETDEWEB)
Proposed features of the competitive electricity market in Ontario were reviewed. The speaker predicted that demand for renewable energy in Ontario`s competitive electricity market will be affected by green power, emissions trading, labelling, and renewables portfolio standard. Under current regulations retailers can charge customers a premium for purchasing electricity generated by `green` sources. The existing limits on emissions of sulphur dioxide, nitrogen oxides and carbon dioxides will remain in place, but an emissions cap and trading program for all Ontario-based generation is an option to consider. Ontario`s Market Design Committee (MDC) has recommended the implementation of emissions trading for electricity-related air pollutants for all generators located in Ontario. The complex mechanics of emission trading are explained. The MDC ...
1998-12-31
Nuclear power plant personnel training in France
International Nuclear Information System (INIS)
Data on French nuclear electricity generation sites, nuclear power plant operations personnel, operation simulators, nuclear training centers and training statistics are presented.
1994-03-21
Energy Technology Data Exchange (ETDEWEB)
An analysis is given of the problems which can be solved by the use of electric-powered vehicles. A detailed comparison is made of the energy consumption and the air polluting emissions of electric and conventional vehicles, taking into account the energy consumption of the vehicles and the primary energy consumption of electric power generation and automotive fuels production. Also the air pollution, as a result of power generation and fuel production are considered. In chapter 1 an outline is given of the traffic and transportation sector in the Netherlands with special attention to data on the energy consumption and the air pollution of this sector. Based on these data the problems can be formulated for which the application of electric vehicles can be a solution. In chapter three a brief description is given of the technical specifications and ...
1992-09-01
Energy Technology Data Exchange (ETDEWEB)
Three systems for the heat supply in the built environment have been compared for the costs, the energy consumption and emissions of CO{sub 2}, NO{sub x} and SO{sub 2}. The heating systems compared are based on central heating boilers, district heating systems in combination with combined steam and gas turbine cycles, and heating by means of several gas engines. From the results it appears that the boilers demand the lowest investments. The district heating systems are more expensive. Both heating systems, however, show considerable savings of energy (55 to 70%). The exploitation costs depend strongly on the fuel price scenarios used and the assumptions with regard to interest and inflation. The emissions of CO{sub 2} are also considerably lower for both combined heat and power generating systems. The use of gas engines results in higher acidifying emissions compared to the system with the central ...
1991-07-01
Hybrid Combined Cycles with Biomass and Waste Fired Bottoming Cycle - a Literature Study
Energy Technology Data Exchange (ETDEWEB)
Biomass is one of the main natural resources in Sweden. The present low-CO{sub 2} emission characteristics of the Swedish electricity production system (hydro and nuclear) can be retained only by expansion of biofuel applications for energy purposes. Domestic Swedish biomass resources are vast and renewable, but not infinite. They must be utilized as efficiently as possible, in order to make sure that they meet the conditions for sustainability in the future. Application of efficient power generation cycles at low costs is essential for meeting this challenge. This applies also to municipal solid waste incineration with energy extraction, which should be preferred to its dumping in landfills. Hybrid dual-fuel combined cycle units are a simple and affordable way to increase the electric efficiency of biofuel energy utilization, without big investments, uncertainties or loss of reliability arising from complicated ...
2002-02-01
Energy Technology Data Exchange (ETDEWEB)
This study presents a full cost approach to determine the levelized cost of energy (LCOE) of 14 electricity generation technologies. It encompasses costs incurred at all stages of the fuel cycle, including those that are traditionally omitted from economic evaluations of generation technologies. Incorporating these 'externalities' increases the likelihood of developing the most economical and sustainable power resource from a societal perspective. The following externalities are included in this analysis: damage from air pollution, energy security, transmission and distribution costs, and other environmental impacts. Incorporating externalities has a large impact on the LCOE and the relative attractiveness of electricity generation options. Results indicate that clean and efficient generation technologies are the most attractive when all ...
2002-12-01
Marketing opportunity for industries/power plants -- the Swedish case
Energy Technology Data Exchange (ETDEWEB)
This paper describes and analyses the new situation in the electricity market in Sweden and the attendant emergence of a unique marketing opportunity for industries and power plants to capitalize on bioenergy. This recent marketing opportunity, which is based on consumer demand, has come about through a number of recent institutional changes in Sweden that have drastically lowered the transaction costs associated with the purchase of green electricity, i.e. electricity generated in what is classified as an environmentally sound manner. This has created a functioning market for green electricity and products made using green electricity.
1996-12-31
Far East combined-cycle update
Energy Technology Data Exchange (ETDEWEB)
Korea Electric Power Corporation (Kepco) of South Korea has awarded Asea Brown Boveri Switzerland, a member of the ABB Group, a contract to supply the main equipment for two gas-fired combined-cycle power stations. News of the contract followed an announcement last year that Kepco will build a series of gas-fired power stations in the early 1990s to supply electricity to new housing and commercial areas being built in the Seoul-Incheon connurbation. (author).
1991-03-01
Catalytic hot gas conditioning of biomass derived product gas
Energy Technology Data Exchange (ETDEWEB)
Biomass gasification provides the potential to efficiently and economically produce a renewable source of a clean gaseous fuel suitable for power generation or synthesis gas (syngas) applications. An important side benefit of the use of biomass is the effective minimization of the primary greenhouse gas, carbon dioxide (CO{sub 2}), by providing a means to close-loop the CO{sub 2} cycle. However, high molecular weight hydrocarbon constituents (tar) in the product gas from gasification can complicate the downstream uses of the gas. This paper discusses both the development of a low cost, disposable catalyst system that can eliminate these heavy hydrocarbons from the gas and the use of the catalyst in conjunction with the Battelle high-throughput gasification process for power generation and synthesis applications. (author)
1997-12-31
In-Use Performance Comparison of Hybrid Electric, CNG, and Diesel Buses at New York City Transit
Energy Technology Data Exchange (ETDEWEB)
The National Renewable Energy Laboratory (NREL) evaluated the performance of diesel, compressed natural gas (CNG), and hybrid electric (equipped with BAE Systems? HybriDrive propulsion system) transit buses at New York City Transit (NYCT). CNG, Gen I and Gen II hybrid electric propulsion systems were compared on fuel economy, maintenance and operating costs per mile, and reliability.
2008-06-01
The operation status and prospect of radioisotope production facility in HANARO
Energy Technology Data Exchange (ETDEWEB)
Researches and production of radio-isotopes, radio-pharmaceuticals and cold kits are carried out in the Radio-isotope Production Facility (RIPF). Four concrete hot cells in Bank-1 are to produce the Ir-192 source for NDT. Eleven lead hot cells in Bank-2 are to produce Ho-166, Cr-51, P-32/33, Tc-99m, Lu-177, Sr-90/Y-90 and W-188/Re-188 for research purpose. Six lead hot cells in Bank-3 are used for the production of I-131 for diagnosis and therapy of cancer in the hospital. A hot cell in Bank-3 is also utilized for the research of I-125 and Br-82. Four lead hot cells in Bank-4 are utilized for the production of Mo-99/Tc-99m generators since 2005. The major systems including the Heat and Ventilated Air Conditioning (HVAC) system and the air cleaning system such as charcoal and HEPA filter trains to filter the radioactive contaminants are in operation. So are the systems such as power supply and distribution system, UPS, fire protection system, liquid radioactive ...
2008-11-15
Natural gas use in Saskatchewan hog industry
Energy Technology Data Exchange (ETDEWEB)
A study was conducted to examine the energy consumption in existing and new hog farming facilities and to analyse the potential for increased natural gas use in the Saskatchewan hog industry. Existing heating/cooling, ventilation and feed mill equipment choices offer possibilities for running on electricity, natural gas or propane. Energy costs are lowest when natural gas is used. To put the study in context, an overview of the Saskatchewan hog industry was provided. The potential increase in natural gas use in hog production by year 2005 was estimated. 10 refs., 6 tabs., 8 figs.
1996-11-01
Electricity production from the biomass of the sugarcane industry in Mauritius
Energy Technology Data Exchange (ETDEWEB)
The analysis of bagasse use indicates that the production of exportable electricity from sugar cane factories in Mauritius can be increased from the current level of between 10 and 20 kWh to around 60 kWh per tonne cane crushed. If the bagasse is dried and pelletized, and cane tops and leaves (CT and L) also used, electricity production can be further increased to around 100-110 kWh per tonne of cane crushed. An economic analysis of the process shows that the cost of electricity generated within the sugar industry in Mauritius is competitive with that of electricity produced from fossil fuels. In addition, it is shown that almost twice the current annual electricity consumption, or the postulated annual electricity consumption for the year 2000, of the island can be provided by the Mauritian Sugar Industry. 10 references.
1984-01-01
The Euro-Quebec Hydro-Hydrogen Pilot Project (EQHHPP). Rationale, concept, realisation
Energy Technology Data Exchange (ETDEWEB)
Back in 1985 it was the European Commission's intention to demonstrate on rather large scale the provision of clean and renewable energy with hydrogen as energy vector and fuel. The cheapest and technologically available form of renewable electricity, the primary energy for electrolytic hydrogen, is hydropower. Most of the hydroenergy sources are oversea's. The World's topologically and technically exploitable hydroenergy potential is estimated to be in the order of 20.10{sup 3} TWh/y, i.e. 0.0057% of the hydraulic cycle energy. Today's hydroelectricity generation is {approx}2500 TWh/y i.e. {approx}21% of the World's electricity generation. Quebec's installed hydroelectricity is 33.5 GW, its residual potential is 50 GW or 190 TWh/y and 285 TWh/y, respectively (load factor 0.65). The construction of hydropower installation is rather clean. The ...
1998-07-01
EPA Utility FGD (Flue Gas Desulfurization) Survey.
The report, generated by a computerized data base system, presents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems, operational domestic particle scrubbers, and Japanese coal-fired utility FGD installations. It ...
1981-01-01
The report discusses the capabilities of equipment vendors to supply and install the quantity of flue gas desulfurization systems required to meet alternative standards for coal-fired steam generators. It analyzes limiting factors affecting supply capabilities (such as the availa...
Energy Technology Data Exchange (ETDEWEB)
Gas-fired combined cycle plant may be the norm when it comes to new plant but it comes in a variety of shapes and sizes. Samarinda uses aero-derivatives with the famous Rolls-Royce RB211 gas generator. (author)
1996-10-01
Depth of origin of the gas content in thermal waters
Energy Technology Data Exchange (ETDEWEB)
The gas composition of recent thermal waters is in perfect conformity with their geologic-tectonic positions. The composition of gas-liquid inclusions in the basic-hyperbasic xenoliths of basaltoid lavas depends on the depth from which xenoliths are supplied. (The depth is determined by using the methods of geological thermobarometers). By comparing available data the conclusion was drawn that the gas compositions of thermal waters reflect the depth of generation of deep fluid which heats them and depends on the penetration depth of the fluid-conducting fissure zones.
1980-01-01
International Nuclear Information System (INIS)
When analyzing the loss-of-coolant accidents at VVER reactor NPP the problem of the effect of noncondensable gases on heat transfer in a horizontal steam generator (HSG) is gaining in importance. Based on the RELAP5/MOD3.2 computer code one analyzed the experiments to condense steam-and-gas mixture in a HSG. The calculations are shown to predict satisfactorily duration of steam generator poisoning from noncondensable gas
2005-03-01
Annual Report 1999. Electric power in Sweden
Energy Technology Data Exchange (ETDEWEB)
Barsebaeck 1 was closed on 30 November 1999. Barsebaeck's output of approximately 4 TWh per year will primarily be replaced by imports from coal-fired plants in Denmark and Germany. During the year, the closure of Swedish fossil-fired condensing power stations continued. With that, over 3,000 MW of peak-load power has been shut down during recent years. Consequently, situations entailing shortages of power can arise. On the deregulated electricity market, it is only the system operators that have a satisfactory overview of the overall electricity balance. The Swedish Power Association has thus lobbied the government as regards the need to elucidate Svenska Kraftnaet's responsibility. In a governmental decision from December, Svenska Kraftnaet was given the task of, among other things, monitoring the available capacity during peak loads and developing market instruments that can contribute to safeguarding the availability of ...
2000-07-15
Particle simulation of edge pedestal formation and plasma rotation dynamics
International Nuclear Information System (INIS)
Gyrokinetic particle simulation of edge pedestal formation and plasma rotation dynamics will be presented, and compared with experimental observations. Realistic tokamak edge geometry is used which include separatrix/X-point and material wall from EFIT g-eqdsk data. In order to handle adequately the spatially inhomogeneous electric potential in the scrape-off region, the full-f electron technique is used, in addition to the full-f ions. Monte Carlo neutral particles with wall recycling coefficient will be included self-consistently with the plasma kinetics. Ion-ion Coulomb collisions will be particle, momentum and energy conserving. Energy source for the pedestal and scrape-off plasmas is the heat flow from the core plasma, and the particle source is the ionization of the neutral atoms which are either wall recycled and/or gas puffed. The simulation will be self-consistent with the first principles nonlinear neoclassical and (electrostatic so ...
2007-03-26
Transient stability enhancement of electric power generating systems by 120-degree phase rotation
Energy Technology Data Exchange (ETDEWEB)
A method and system for enhancing the transient stability of an intertied three-phase electric power generating system. A set of power exporting generators (10) is connected to a set of power importing generators (20). When a transient cannot be controlled by conventional stability controls, and imminent loss of synchronism is detected (such as when the equivalent rotor angle difference between the two generator sets exceeds a predetermined value, such as 150 degrees), the intertie is disconnected by circuit breakers. Then a switch (30) having a 120-degree phase rotation, or a circuit breaker having a 120-degree phase rotation is placed in the intertie. The intertie is then reconnected. This results in a 120-degree reduction in the equivalent rotor angle difference between the two generator sets, making the system more stable and allowing more time for the ...
1982-01-01
The alkali sorption process by solid sorbents at high temperature
Energy Technology Data Exchange (ETDEWEB)
The removal of toxic metals and alkalis from gas streams at high temperatures was investigated. This is important for the development of coal-fired combined cycle power generation systems.
2000-03-01
material may survive intact and mix back into interstellar gas clouds, helping to fuel the next generation of stars. NASA's Jet Propulsion Laboratory, Pasadena, Calif.,...
2011-08-10
Energy Technology Data Exchange (ETDEWEB)
The genetic type, source and charging history of natural gas in the Yulin gas field in the Ordos Basin have been studied by combining the carbon isotopic composition of natural gas and geochemical characteristics of light hydrocarbons with carbon isotope fractionation model results and fluid inclusion analysis. The carbon isotopic composition of methane and ethane in the Yulin gas field is relatively enriched in {sup 13}C with {delta}{sup 13}C{sub 1} values ranging from - 35.3 permille to - 29.8 permille (average value = - 32.4 permille) and {delta}{sup 13}C{sub 2} ranging from - 26.3 permille to - 23.5 permille (average value = - 24.8 permille). The C{sub 7} light hydrocarbons are predominated by methylcyclohexane, accounting for 65.8% to 80.9% (average value = 71.6%), which is characteristic of coal-derived gas. Furthermore, the gas geochemistry indicates ...
2010-04-01
ENERGY EFFICIENCY AND ENVIRONMENTALLY FRIENDLY DISTRIBUTED ENERGY STORAGE BATTERY
Energy Technology Data Exchange (ETDEWEB)
Electro Energy, Inc. conducted a research project to develop an energy efficient and environmentally friendly bipolar Ni-MH battery for distributed energy storage applications. Rechargeable batteries with long life and low cost potentially play a significant role by reducing electricity cost and pollution. A rechargeable battery functions as a reservoir for storage for electrical energy, carries energy for portable applications, or can provide peaking energy when a demand for electrical power exceeds primary generating capabilities.
2006-04-30
A magneto-electric quantum wheel
Here we show that self-propulsion in quantum vacuum may be achieved by rotating or aggregating magneto-electric nano-particles. The back-action follows from changes in momentum of electro-magnetic zero-point fluctuations, generated in magneto-electric materials. This effect may provide new tools for investigation of the quantum nature of our world. It might also serve in the future as a "quantum wheel" to correct satellite orientation in space.
2009-01-01
Advanced applications of water cooled nuclear power plants
International Nuclear Information System (INIS)
By August 2007, there were 438 nuclear power plants (NPPs) in operation worldwide, with a total capacity of 371.7 GW(e). Further, 31 units, totaling 24.1 GW(e), were under construction. During 2006 nuclear power produced 2659.7 billion kWh of electricity, which was 15.2% of the world's total. The vast majority of these plants use water-cooled reactors. Based on information provided by its Member States, the IAEA projects that nuclear power will grow significantly, producing between 2760 and 2810 billion kWh annually by 2010, between 3120 and 3840 billion kWh annually by 2020, and between 3325 and 5040 billion kWh annually by 2030. There are several reasons for these rising expectations for nuclear power: - Nuclear power's lengthening experience and good performance: The industry now has more than 12 000 reactor years of experience, and the global average nuclear plant availability during 2006 reached 83%; - Growing energy needs: All forecasts project increases in ...
2007-07-01
Advanced applications of water cooled nuclear power plants
International Nuclear Information System (INIS)
By August 2007, there were 438 nuclear power plants (NPPs) in operation worldwide, with a total capacity of 371.7 GW(e). Further, 31 units, totaling 24.1 GW(e), were under construction. During 2006 nuclear power produced 2659.7 billion kWh of electricity, which was 15.2% of the world's total. The vast majority of these plants use water-cooled reactors. Based on information provided by its Member States, the IAEA projects that nuclear power will grow significantly, producing between 2760 and 2810 billion kWh annually by 2010, between 3120 and 3840 billion kWh annually by 2020, and between 3325 and 5040 billion kWh annually by 2030. There are several reasons for these rising expectations for nuclear power: - Nuclear power's lengthening experience and good performance: The industry now has more than 12 000 reactor years of experience, and the global average nuclear plant availability during 2006 reached 83%; - Growing energy needs: All forecasts project increases in ...
1996-07-21
Advanced applications of water cooled nuclear power plants
International Nuclear Information System (INIS)
By August 2007, there were 438 nuclear power plants (NPPs) in operation worldwide, with a total capacity of 371.7 GW(e). Further, 31 units, totaling 24.1 GW(e), were under construction. During 2006 nuclear power produced 2659.7 billion kWh of electricity, which was 15.2% of the world's total. The vast majority of these plants use water-cooled reactors. Based on information provided by its Member States, the IAEA projects that nuclear power will grow significantly, producing between 2760 and 2810 billion kWh annually by 2010, between 3120 and 3840 billion kWh annually by 2020, and between 3325 and 5040 billion kWh annually by 2030. There are several reasons for these rising expectations for nuclear power: - Nuclear power's lengthening experience and good performance: The industry now has more than 12 000 reactor years of experience, and the global average nuclear plant availability during 2006 reached 83%; - Growing energy needs: All forecasts project increases in ...
2007-11-23
International Nuclear Information System (INIS)
The Institute of Electrical and Electronic Engineers (IEEE) standards for the quality assurance requirements for the design and manufacture of Class 1E instrumentation and electric equipment for a nuclear power generating station are presented. This standard establishes Quality Assurance Program requirements for electrical manufacturers. This standard, used in conjunction with ANSI N45.2-1977 and the supplemental standards to the extent referenced in this standard, is intended to meet the requirements of 10CFR50, Appendix B. These requirements are intended to assure that Class 1E instrumentation and electric equipment are responsibly engineered and manufactured from proper materials, that the manufacturing processes and practices are controlled, and that the manufacturing process produces a product of the required quality for Class 1E application.
Electrical wind generation, feasibility study and analysis in Lebanon
International Nuclear Information System (INIS)
Full text.This paper is to investigate the potentials and possibilities of electrical generation via wind turbine. Special attention is directed to the interpretation of wind generation characteristics and parameters found in Lebanon and linking the electrical energy to the Lebanese slectric grid. Although much of the wind energy research is very well established and boomed globally (USA, Europe, India and China), in Lebanon is never used. At a time when climate scientists are increasingly concerned about carbon dioxide emissions from coal and diesel plants, and the nuclear industry is drying, the significance of a major new source os electricity is clear. there are many motives and feasibility criteria for qind power generation in Lebanon. They include the need for increasing the Lebanese electrical capacity, reducing air pollution, ...
1999-11-02
Ultra-thin {sup 242m}Am fuel elements in nuclear reactors
Energy Technology Data Exchange (ETDEWEB)
There is a growing interest in using {sup 242m}Am as a nuclear fuel. The advantages of {sup 242m}Am as a nuclear fuel derive from the fact that {sup 242m}Am has the highest thermal fission cross section. The thermal capture cross section is relatively low and the number of neutrons per thermal fission is high. These nuclear properties make it possible to obtain nuclear criticality with ultra-thin fuel elements. The possibility of having ultra-thin fuel elements enables the use of these fission products directly, without the necessity of converting their energy to heat, as is done in conventional reactors. There are three options of using such highly energetic and highly ionized fission products. - Using the fission products themselves for ionic propulsion. - Using the fission products in an MHD generator, in order to obtain electricity directly. - Using the fission products to heat a gas up to a high temperature for ...
2000-12-01
Energy Technology Data Exchange (ETDEWEB)
The DOE-Utility Nuclear Power Engineering Education Matching Grant Program has been established to support the education of students in Nuclear Engineering Programs to maintain a knowledgeable workforce in the United States in order to keep nuclear power as a viable component in a mix of energy sources for the country. The involvement of the utility industry ensures that this grant program satisfies the needs and requirements of local nuclear energy producers and at the same time establishes a strong linkage between education and day-to-day nuclear power generation. As of 1997, seventeen pairs of university-utility partners existed. UMCP was never a member of that group of universities, but applied for the first time with a proposal to Baltimore Gas and Electric Company in January 1999 [1]. This proposal was generously granted by BG&E [2,3] in the form of a gift in the amount of $25,000 from BG&E's ...
2000-03-01
Storing hydroelectricity to meet peak-hour demand
Energy Technology Data Exchange (ETDEWEB)
This paper reports on pumped storage plants which have become an effective way for some utility companies that derive power from hydroelectric facilities to economically store baseload energy during off-peak hours for use during peak hourly demands. According to the Electric Power Research Institute (EPRI) in Palo Alto, Calif., 36 of these plants provide approximately 20 gigawatts, or about 3 percent of U.S. generating capacity. During peak-demand periods, utilities are often stretched beyond their capacity to provide power and must therefore purchase it from neighboring utilities. Building new baseload power plants, typically nuclear or coal-fired facilities that run 24 hours per day seven days a week, is expensive, about $1500 per kilowatt, according to Robert Schainker, program manager for energy storage at the EPRI. Schainker the that building peaking plants at $400 per kilowatt, which run a few hours a day on gas or ...
1992-04-01
Storing hydroelectricity to meet peak-hour demand
International Nuclear Information System (INIS)
This paper reports on pumped storage plants which have become an effective way for some utility companies that derive power from hydroelectric facilities to economically store baseload energy during off-peak hours for use during peak hourly demands. According to the Electric Power Research Institute (EPRI) in Palo Alto, Calif., 36 of these plants provide approximately 20 gigawatts, or about 3 percent of U.S. generating capacity. During peak-demand periods, utilities are often stretched beyond their capacity to provide power and must therefore purchase it from neighboring utilities. Building new baseload power plants, typically nuclear or coal-fired facilities that run 24 hours per day seven days a week, is expensive, about $1500 per kilowatt, according to Robert Schainker, program manager for energy storage at the EPRI. Schainker the that building peaking plants at $400 per kilowatt, which run a few hours a day on gas or ...
1992-01-01
PANDA passive decay heat removal transient test results
International Nuclear Information System (INIS)
PANDA is a large scale facility for investigating the long-term decay heat removal from the containment of a next generation of 'passive' Advanced Light Water Reactors (ALWR). PANDA was used to examine the long-term LOCA response of the Passive Containment Cooling System (PCCS) for the General Electric (GE) Simplified Boiling Water Reactor (SBWR). The first PANDA test series had the dual objectives of demonstrating the performance of the SBWR PCCS and extending the data base available for containment analysis code qualification. The test objectives also include the study of the effects of mixing and stratification of steam and noncondensible gases in the drywell (DW) and in the suppression chamber or wetwell (WW). Ten tests were conducted in the course of the PANDA SBWR Program. The tests demonstrated a favorable and robust overall PCCS performance under different conditions. The present paper focuses on the main phenomena observed during the ...
New intelligent monitor for CANDU type NPP
International Nuclear Information System (INIS)
Nuclear energy provides a third of Europe's electricity with nearly no greenhouse-gas emissions. Sustained efforts are now being conducted to harmonize regulations all over Europe through WENRA and to converge on technical nuclear safety practices within the TSO network ETSON (European Technical Safety Organizations Network). In CANDU type NPP the tritiated water occurs by the neutron bombardment of deuterium. The tritiated water vapors imply health hazard (in the critical organs of the body the water presents a 10 day average biological half-life) and the early detection in nuclear plants of tritium emissions is important because the tritiated water vapors have the same characteristics as of atmospheric water vapors. By detecting tritiated vapors, the monitoring system ensures the following objectives: (a) indicates levels of tritium generally due to heavy water leakage, (b) reduces the possibility of health hazard. In order to attain this ...
2009-10-12
Energy Technology Data Exchange (ETDEWEB)
Studies are made on electrode behaviors of hydride ion in eutectic LiCl-KCl molten salt by various electrochemical methods. As a result, it is confirmed and clarified, by cyclic voltammetry, that anode reaction of hydride ion exists and it is a diffusion-controlled, reversible and one-electron reaction. Also, generation of hydrogen gas is confirmed by a potentiostatic electrolysis, and the electrolysis in the current efficiency of about 95% is possible by controlling electric potential. Moreover, results of chronopotentiometry and chronoamperometry show that hydride ion is anodically oxidized by the diffusion controlling reaction and the reaction itself is reversible. Results of cyclic voltammetry indicate that a diffusion constant D{sub H} {sup {minus}} equals 3.0 {times}10 {sup {minus}5}cm{sup 2}{center dot}S{sup {minus}1} (425 centigrade). This value corresponds well to the values estimated from chronopotentiometry and ...
1991-09-05
Clear liquor scrubbing with anhydrite production. Fourth quarter 1996 technical progress report
Energy Technology Data Exchange (ETDEWEB)
This project is part of PETC`s Advanced Power Systems Program, whose mission is to accelerate the commercialization of affordable, high- efficiency, low emission, coal-fueled electric generating technologies. A process concept - Clear Liquor Scrubbing with Anhydrite Production - was proposed and accepted by PETC as a Phase I project in its Mega-PRDA program. the project integrated three process operations - chloride control upstream of the flue gas desulfurization (FGD) system, a clear liquor process for enhanced SO{sub 2} removal performance, and production of anhydrite (anhydrous calcium sulfate) rather than calcium sulfite or gypsum (calcium sulfate dihydrate). The first step in the project was to perform batch and flow-through experiments in the laboratory to confirm theoretical calculations and preliminary laboratory results concerning anhydrite formation, these laboratory experiments were designed to prove that ...
1997-02-03
CO{sub 2} trading systems undergo quiet experimentation
Energy Technology Data Exchange (ETDEWEB)
Issues regarding the development of mechanisms to reduce greenhouse gas emissions in the electricity sector are discussed. Environmental groups have proposed mechanisms such as carbon taxes. Three other mechanisms have also been proposed under the Framework Convention on Climate Change (FCCC). These include the Clean Development Mechanism, Joint Implementation and carbon trading. A pilot emission reduction trading project began in Ontario in 1996 as an initiative to control smog and ozone in the southern provincial airshed. Substances of interest include NO{sub x}, volatile organic compounds (VOCs), SO{sub x}, carbon monoxide and other greenhouse gases. Ontario Hydro alone has conducted 10 trades, five with companies in the U.S., two of those for carbon emissions. An analysis of the pilot trade deals will provide an idea of the value of this mechanism. In addition to details of the trades, this article also addresses concerns regarding the ...
1999-02-01
Energy Technology Data Exchange (ETDEWEB)
Smart electricity and gas supply grids are a prerequiste for full-scale utilization of the potential of modern energy-saving appliances and equipment. Direct exchange of information between the supplier and the consumer is indispensable for reducing costly and energy-intensive peak loads. (orig.)
2010-09-15
Energy Technology Data Exchange (ETDEWEB)
Rotary furnaces are a well established alternative to cupola furnaces. Recent innovations in oxygas furnaces have made them the preferred choice even over medium-frequency electric furnaces in many European foundries. The article explains in what respects the rotary furnace is a new iron smelting concept, as different from the cupola furnace as the medium-frequency electric furnace. (author)
2001-10-01
Electrical properties of airborne nanoparticles produced by a commercial spark-discharge generator
International Nuclear Information System (INIS)
A nanoparticle generator based on the principle of electrical discharge (PALAS GFG-1000) was used to produce nanoparticles of different chemical natures. The fractions of electrically neutral particles were then measured by means of a Spectrometre de Mobilite Electrique Circulaire (SMEC, i.e. radial-flow mobility analyzer) for different operating conditions. The experimental results were compared with the theoretical values calculated from the Fuchs extended charge equilibrium model for spherical particles and agglomerates. For the smallest particles (below 20 nm), the deviations observed remain below 10%, and tend towards 20% for larger particles (over 35 nm).
2010-08-01
Application of the porous media model for the LWR process components
Energy Technology Data Exchange (ETDEWEB)
Full text of publication follows: A porous media solution PORFLO has been developed for the 3-dimensional two-phase flow by describing the process facility in Cartesian or cylindrical coordinates. The local porosity fraction is applied for distinguishing the fluid filled volumes from the solid structures. The solid structure contribute the two-phase flow through the wall friction, flow area and heat transfer. Optionally the solid structure may contain primary liquid of steam generators, steam in the higher temperature and pressure to be condensed or electrical heating power. By using these optional boundary conditions three different process facilities have been analysed. The thermohydraulic solution based on 5-equation approach, where the conservation equations are solved for the liquid and gas (vapour) mass, mixture momentum (giving the velocity only for the mixture), liquid and gas energy, is ...
2005-07-01
In the current wind turbine generation system, there are substantial problems such as the maximum power of the wind turbine cannot be obtained under the fluctuating wind speed, high in cost and low in annual net electricity production (due to mismatch between a generator and a wind turbine). A new wind turbine generator optimized for the wind turbine output is presented in order to solve such problems. This wind turbine generator consists of a permanent magnet generator, a reactor and a rectifier, and uses neither a control circuit which requires standby electricity nor a PWM converter having a switching element. By selecting most appropriate combination of the permanent magnet generator having multiple windings and the reactor connected in series with each winding, the maximum output of the wind turbine can be obtained ...
2008-01-01
Oil-filled cable surveillance system using newly developed optical fiber gas sensor
Energy Technology Data Exchange (ETDEWEB)
A new surveillance system for Oil-Filled cable, which can provide continuous monitoring, using a newly developed optical gas sensor that can detect the concentration of the gas dissolved in the oil with extremely high sensitivity has been developed. It was proved that the degree of deterioration of the insulating oil can be detected by measuring C{sub 2}H{sub 2} and CH{sub 4} by investigating the relation between the degree of deterioration and amount of combustible gas generated. In order to detect extremely small amounts of gas, a new gas detecting method using absorption line of the gas using a frequency modulated technique has been developed. The gas detection ability was also confirmed by examination using a 66 kV of cable and the possibility of detection at an early stage is expected.
1996-04-01
Evaluation of the maximum horsepower of vehicles converted for use with natural gas fuel
Energy Technology Data Exchange (ETDEWEB)
Tests to measure the maximum horsepower of commercial vehicles converted for use with natural gas fuel indicate a reduction of approximately 20% in horsepower compared with gasoline-driven vehicles. This reduction in horsepower resulting from the use of gas is due basically to the lower thermal efficiency of the cycle of natural gas compared with that of gasoline and to its lower volumetric efficiency, since natural gas is injected into the combustion chamber in gaseous form, unlike gasoline, in which part of the fuel entering the cylinder is in the liquid phase. Natural gas used as a fuel generates lower quantities of air pollutants, particularly unburned hydrocarbons (HCs) and carbon monoxide (CO). Despite the downside of reduced horsepower, the use of natural gas as a fuel for automotive vehicles equipped with Otto-cycle engines is ...
2006-10-15
Fast generation shedding equipment based on the observation of swings of generators
Energy Technology Data Exchange (ETDEWEB)
This paper presents a new method and newly developed stabilizing equipment to prevent the loss of synchronism of generators in pumped-storage plants from spreading. The proposed method includes functions to estimate the swing of each generator by using on-line generator output sampled at a rate of 600 times per second after an occurrence of disturbance such as fault, faulty equipment and so on, to predict generator swing 200-300 milliseconds ahead and loss of synchronism between generators in pumped-storage plants and those in thermal and nuclear plants, and to decide the number of generators that must be shed to maintain stability. Tokyo Electric Power Co. (TEPCO) installed the newly developed stabilizing equipment based on this method in the power system in June, 1986.
1988-05-01
Fast generation shedding equipment based on the observation of swings of generators
International Nuclear Information System (INIS)
This paper presents a new method and newly developed stabilizing equipment to prevent the loss of synchronism of generators in pumped-storage plants from spreading. The proposed method includes functions to estimate the swing of each generator by using on-line generator output sampled at a rate of 600 times per second after an occurrence of disturbance such as fault, faulty equipment and so on, to predict generator swing 200-300 milliseconds ahead and loss of synchronism between generators in pumped-storage plants and those in thermal and nuclear plants, and to decide the number of generators that must be shed to maintain stability. Tokyo Electric Power Co. (TEPCO) installed the newly developed stabilizing equipment based on this method in the power system in June, 1986.
1988-01-01
Energy Technology Data Exchange (ETDEWEB)
The object of this survey of small US electric utility systems was to determine the potential utilization of small, fuel-flexible, advanced-cycle combustion turbines for power generation. Three prototype concepts were evaluated. Concept A: a 2.5 MWe externally fired, closed-cycle combustion turbine, with fluidized-bed combustor, burning solid fuels. Concept B: an open 3.8 MWe, indirect-fired, combined-cycle turbine system using solid, liquid or gaseous fuels, with downstream stack cleanup. Concept C: 11.6 MWe, utilizing an open, direct-fired, combined-cycle turbine arrangement, gas or oil fueled employing components of advanced development. It was presumed such units might be commercially available circa 1985 to 1990. Fifty-three utilities, encompassing a variety of ownerships, geographical distribution and system sizes, were interviewed on-site. Questions covered the probable use of such generating ...
1981-04-01
British Library Electronic Table of Contents (United Kingdom)
The steam generator is a very important component of a nuclear power plant. Historically, vertical steam generators came to be used abroad and horizontal steam generators in our country. Both types of steam generators operate successfully in nuclear power plants and satisfactorily fulfill their functions, enabling the production of electricity. Repeated attempts to re-examine the existing concepts in one or another country have been unsuccessful because there are no convincing arguments for this. Nonetheless, the question of using a different type of steam generator is raised periodically in our country and abroad. This article briefly reviews different concepts of steam generators. Their parameters, characteristics, and thermal efficiency are compared and ways to increase the latter are a...
2008-01-01
Status of electric power in the Missouri River Basin
Energy Technology Data Exchange (ETDEWEB)
This third Missouri River Basin Commission report on Status of Electric Power in the Missouri River Basin provides information on the status of electric power generation, future needs, and potentials for meeting these needs. Information for this 1980 update is based upon available published information up to and including December 31, 1979. State and federal members of the Missouri River Basin Commission provided information for sections of the report and on legislative activities. Information is included on the planning and projected costs of hydro, nuclear and fossil-fuel power plants, pumped-storage plants, transmission systems, projected power demands, the environmental, socio-economic-cultural impacts of electric power generation, and regulations affecting energy development. (LCL)
1980-01-01
British Library Electronic Table of Contents (United Kingdom)
In this work, we propose a conceptual distributed control framework for electrical grid integrated with distributed renewable energy generation systems in order to enable the development of the so-called ''smart electrical grid''. First, we introduce the key elements and their interactions in the proposed control architecture and discuss the design of the distributed control systems which are able to coordinate their actions to account for optimization considerations on the system operation. Subsequently, we focus on a specific wind/solar energy generation system connected to a reverse osmosis water desalination system and the electrical grid and design two supervisory predictive controllers via model predictive control to operate the integrated system taking into account short-term and lo...
2011-01-01
Impact of partitioning and transmutation on the high level waste management
British Library Electronic Table of Contents (United Kingdom)
Nuclear energy generates 30% of the electricity in the EU. Still, different countries of EU27 have very different attitudes towards the future use of nuclear energy for electricity generation or other uses. However, independently of the political decision of continuation or phase out of the nuclear energy, all countries using nuclear energy to generate electricity are facing the question of the final management of its spent nuclear fuel and other high level radioactive wastes. Partition and Transmutation are emerging technologies that when integrated in advanced fuel cycles can strongly influence on the final wastes from the nuclear industry and its management. A review of the progress on the understanding of their real potentialities and main conclusions from a large number of internation...
2011-01-01
International Nuclear Information System (INIS)
This paper presents some situations, in which measurements of electromagnetic fields generated by transmission lines and substations should be performed. The range of measurements may differ, but maximum values of electric and magnetic fields and flux density must be identified in all situations. The area with electric field exceeding 1 kV/m should be identified as well. The author also presents basic requirements to be met by the measurement technique. These requirements are specified according to the national standard. Special attention should be paid to the identification of the spatial distribution of electric field and flux density generated in the vicinity of high voltage transmission lines. To verify the measurement results, it is necessary to calculate the distribution of both aforesaid field components. For environmental protection purposes, it is also proposed that the ...
2007-01-01
Analysis of even harmonics generation in an isolated electric power system
British Library Electronic Table of Contents (United Kingdom)
Harmonics bred from loads are mainly odd order because the current waveforms have half-wave symmetry. Since the even harmonics are negligibly small, they generally are not measured in electric power systems. However, even harmonics were measured at a 500/275/154 kV substation in Hokuriku Electric Power Company after a transmission line fault was corrected. The even harmonics caused malfunctions of protective digital relays because the relays used 4th harmonics at the input filter as the automatic supervisory signal. This paper describes mechanisms of generation of the even harmonics by comparing the measured waveforms with the ATP-EMTP simulation results. Analysis of these results has clearly shown that there are three different mechanisms of generation of even harmonics. The first mechani...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
The project aim is to model the hybrid plant at Vaesthamnsverket in Helsingborg using artificial neural networks (ANN) and integrating the ANN models, for online condition monitoring and thermoeconomic optimization, at Vaesthamnsverket. The definition of a hybrid plant is that it uses more than one fuel, in this case a natural gas fuelled gas turbine with heat recovery steam generator (HRSG) and a biomass fuelled steam boiler with steam turbine. The project is a continuation of previous projects where ANN training was done with operational data from the plant. The ANN models have, if required, been updated to better suit the purpose of this project. The thermoeconomic optimization takes into account current electricity prices, taxes, fuel prices etc. and calculates the current production cost along with the 'predicted' production cost. The tool also has a built in feature of predicting ...
2007-12-15
Fuel gas from cattle or chicken manure
Energy Technology Data Exchange (ETDEWEB)
Cattle or chicken manure is pelletized, and a bed of the pellets is combusted at the bottom to create a temperature gradient and to generate a fuel gas. Thus, an approximately 25 cm-high bed of approximately 5 mm-diameter chicken manure pellets was combusted to produce a fuel gas of 1622 kcal/kg manure.
1981-05-18
Energy Technology Data Exchange (ETDEWEB)
The pollutants from the exhausts of internal combustion engines cause a range of illnesses and are the main source of atmospheric contamination. This article explores the options for curbing pollution in the UK including catalytic converters, electric cars, and natural gas cars. It is likely that the onus will remain with the car manufacturers for developing solutions. (UK)
1994-11-10
UK PubMed Central (United Kingdom)
Objectives. Thousands of Louisiana residents were asked to boil water because of widespread disruptions in electricity and natural gas services after Hurricane Rita. We sought to assess...Full Text Available
2007-04-01
Energy in Lebanon: main conjuncture indicators
International Nuclear Information System (INIS)
A survey on electric power and on energy balance especially primary and final energy (gas oil, kerosene,solar energy...) has been implemented in Lebanon in 1993. Results and economic impact of energy consumption and energy production are given in statistics and tables. 10 figs.
Automated Energy Distribution and Reliability System (AEDR): Final Report
Energy Technology Data Exchange (ETDEWEB)
This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.
2008-07-01
Energy Technology Data Exchange (ETDEWEB)
In our previous work, we demonstrated that biomass-generated producer gas can be converted to ethanol and acetic acid using a microbial catalyst Clostridium carboxidivorans P7{sup T}. Results showed that the producer gas (1) induced cell dormancy, (2) inhibited H{sub 2} consumption, and (3) affected the acetic acid/ethanol product distribution. Results of this work showed that tars were the likely cause of cell dormancy and product redistribution and that the addition of a 0.025{mu}m filter in the gas cleanup negated the effects of tars. C. carboxidivorans P7{sup T} can adapt to the tars (i.e. grow) only after prolonged exposure. Nitric oxide, present in the producer gas at 150ppm, is an inhibitor of the hydrogenase enzyme involved in H{sub 2} consumption. We conclude that significant conditioning of the producer gas will be required for the successful coupling ...
2006-07-15
Power generation growth to triple LNG use
Energy Technology Data Exchange (ETDEWEB)
Taiwan`s LNG consumption is planned to rise more than threefold over the next four years as medium-term plans to develop power generation facilities increasingly rely on gas-fired combined-cycle stations to avoid the threat of power shortages. State-run Taiwan Power Company (Taipower) expects its LNG consumption to rise from 1.1 mn tonnes in 1996 to 3.4 mn tonnes in the year 2000. By then the first of several gas-fired private power stations is expected to enter service, further increasing Taiwan`s total LNG requirement for power generation. (Author)
1997-11-01
Energy Technology Data Exchange (ETDEWEB)
Extensive research into the treatment and control of Volatile Organic Compounds (VOCs) from semiconductor industry manufacturing processes has identified the need for alternatives to existing combustion devices. Specifically, semiconductor manufacturing design is moving toward exploiting effective, small-scale, abatement control technologies for specific point-of-use (POU) waste streams associated with a particular component or manufacturing tool. The Silent Discharge Plasma (SDP) developed at Los Alamos National Laboratory is a nonthermal plasma technology created by a dielectric-ballasted electrical discharge. Influent gas-phase pollutants are destroyed in the reactor by the free radicals or electrons generated by the plasma. This paper examines the potential for SDP to be used in niche circumstances for POU control of VOC exhaust streams specific to the semiconductor industry. A sensitivity analysis is presented, showing ...
1997-07-01
Gases in insulating oil - analysis of dissolved gases using a portable chromatograph
Energy Technology Data Exchange (ETDEWEB)
New technological advances make it possible to perform on site gas-in-oil analysis quickly and efficiently. Gas-in-oil analysis is crucial in assessing the status of oil-filled electrical equipment. The new technique is used for extracting and measuring gases dissolved in electrical insulating oil. On-site sampling requires the use of a specially designed 100 ml capacity syringe. Extraction of the dissolved gases is made with a precise ratio of oil to air. A comparison was made between the analysis of the on-site and the laboratory techniques. Results showed that the detection limits of the on-site technique were comparable to those obtained by laboratory methods.
1996-07-01
Final report on electric vehicle activities, September 1991--October 1994
Energy Technology Data Exchange (ETDEWEB)
The data and information collected for the Public Service Electric and Gas Company`s (PSE&G) electric vehicle demonstration program were intended to support and enhance DOE`s Electric and Hybrid Vehicle Site Operator Program. The DOE Site Operator Program is focused on the life cycle and reliability of Electric Vehicles (EVs). Of particular interest are vehicles currently available with features that are likely to be put into production or demonstrate new technology. PSE&G acquired eight GMC Electric G-Vans in 1991, and three TEVans in 1993, and conducted a program plan to test and assess the overall performance of these electric vehicles. To accomplish the objectives of DOE`s Site Operator`s test program, a manual data collection system was implemented. The manual data collection system has provided energy use and mileage data. From ...
1995-02-01
Energy Technology Data Exchange (ETDEWEB)
This paper describes research and development activities at the University of Regina, Saskatchewan, Canada on Optimization of CO{sub 2} Extraction Process Technologies. The ultimate goal of this research is to develop better and more effective CO{sub 2} separation processes which can be used to recover CO{sub 2} from industrial sources such as coal-fired power plants and coal gasification complexes at the lowest possible capital and operating costs. The research program has been supported by Saskatchewan Power Corporation, Saskatchewan Energy and Mines, Prairie Coal Ltd., the Canada Centre for Mineral and Energy Technology (CANMET), Fluor Daniel Inc. (USA), Sulzer Chemtech (Switzerland), Wascana Energy Inc., and Natural Sciences and Engineering Research Council of Canada (NSERC). Currently, six parallel and complementary projects have been carried out at the Process Systems Laboratory. These projects are: (1) Searching for new sterically hindered amines for high capacity absorption of ...
1996-05-01
J/Psi dissociation in parity-odd bubbles
We calculate the quarkonium dissociation rate in the P and CP-odd domains (bubbles) that were possibly created in heavy-ion collisions. In the presence of the magnetic field produced by the valence quarks of colliding ions, parity-odd domains generate electric field. Quarkonium dissociation is the result of quantum tunneling of quark or antiquark through the potential barrier in this electric field. The strength of the electric field in the quarkonium comoving frame depends on the quarkonium velocity with respect to the background magnetic field. We investigate momentum, electric field strength and azimuthal dependence of the dissociation rate. Azimuthal distribution of quarkonia surviving in the electromagnetic field is strongly anisotropic; the form of anisotropy depends on the relation between the electric and magnetic fields and quarkonium momentum. These ...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
TSS (thermal swing sublimation) method was studied which uses vaporization heat and sensible heat of LNG for solidification and separation of CO2 gas in waste gases of LNG-fired combined cycle power generation system. In experiment, the mixed gas composed of CO2, H2O and N2 was used for simulating waste gas of LNG-fired combined cycle power generation systems, and the growth behavior of ice and dry ice was studied for developing dry ice making technology under low-temperature condition. As the experimental result, the following were clarified: various crystal structures depending on cooling temperature, the effect of gas flow rate on peeling of surface precipitated solids, and solidification characteristics of H2O/CO2 mixed gas. The growth rate of precipitated solid film thickness decreased with an increase in gas flow ...
1997-03-21
International Nuclear Information System (INIS)
In the beginning of 2005 several changes in the electricity and natural gas market law came into effect. This report examines the influence and impact of these changes on the behaviour and development of these markets, looking at the role and position of both the energy industry and customers. The report combines existing data with new research data collected during spring and summer 2006. Whilst the recency of the law changes, along with the simultaneous impact of other market variables limits the salience of any impact, the report nevertheless provides clear and interesting conclusions. In the electricity market, one major legislative change that came into force in the beginning of 2005 concerned the supervision of the reasonableness of electricity distribution pricing. According to the newly adopted ex ante regulation principles, the regulatory authority now determines the guidelines for reasonable ...
Energy Technology Data Exchange (ETDEWEB)
Tohoku Electric Power Co., Ltd., is now building an LNG-fired No. 4 System (combined cycle of 1.61-million kW) for its Higashi Niigata Thermoelectric Power Station sited in the Niigata East Harbor industrial zone. This is a unit that aims at a thermal efficiency of 50% first in the world by using high-efficiency gas turbines, etc. After the completion of the No. 4 System, the station (No. 1 Machine, No. 2 Machine; No. 3 System, No. 4 System; Harbor No. 1 Machine, Harbor No. 2 Machine) will be generating a total power of 4.6kW, providing the company with its maximum power source which ranks among the largest-grade thermoelectric power stations in this country. Since the construction work was started in April, 1996, approximately 40% had been completed as of March-end, 1997, including foundations for the power station main building, stack, etc. The power station main building uses a raft foundation while the boilers and stack ...
1997-07-05
Energy Technology Data Exchange (ETDEWEB)
A home-made 3.1 kWh wind turbine that is promising to be the hottest new wind product to appear for home/farm users in some time, is described. The turbine is installed near a farm house in the high wind area of Mount Forest, Ontario. The turbine is hooked up to a four kilowatt Trace inverter charger which is coupled through a DC disconnect and C-60 charge controller to two sets of solar panels (seven panels of 120 W each by Solarex SX 120, and five panels by Sharp, each providing 1600 watt of solar power). The wind turbine and the solar panels, assisted by two 65-year old refurbished wind turbines, one bank of Gel Cell batteries, and an Onan 5 kW gas generator supply the electrical requirements of a seven member family in a 3400 square foot house. The new turbine is mounted on an 80-foot tower, has three eight foot Kevlar blades that produce a 17 foot overall sweep. The turbine weighs 615 lbs., produces 3.1 kW of pure ...
2004-12-31
Energy Technology Data Exchange (ETDEWEB)
A study of advancements in power plant designs for use at geothermal resources in the low to moderate (300 to 400F) temperature range is reported. In 3 case studies, the benefits of R and D to achieve these advancements are evaluated in terms of expected increases in installed geothermal generating capacity over the next 2 decades. A parametric sensitivity study is discussed which analyzes differential power development for combinations of power plant efficiency and capitol cost. Affordable tradeoffs between plant performance and capital costs are illustrated. The independent review and analysis of the expected costs of construction, operation and maintenance of the Heber Binary Cycle Geothermal Power Demonstration Plant are described. Included in this assessment is an analysis of each of the major cost components of the project, including (1) construction cost, (2) well field development costs, (3) fluid purchase costs, and (4) well field and power plant operation ...
1983-06-30
Overview of electrochemical power sources for electric and hybrid-electric vehicles.
Energy Technology Data Exchange (ETDEWEB)
Electric and hybrid-electric vehicles are being developed and commercialized around the world at a rate never before seen. These efforts are driven by the prospect of vehicles with lower emissions and higher fuel efficiencies. The widespread adaptation of such vehicles promises a cleaner environment and a reduction in the rate of accumulation of greenhouse gases, Critical to the success of this technology is the use of electrochemical power sources such as batteries and fuel cells, which can convert chemical energy to electrical energy more efficiently and quietly than internal combustion engines. This overview will concentrate on the work being conducted in the US to develop advanced propulsion systems for the electric and hybrid vehicles, This work is spearheaded by the US Advanced Battery Consortium (USABC) for electric vehicles and the Partnership for a New ...
1999-02-12
3-D modelling the electric field due to ocean tidal flow and comparison with observations
DEFF Research Database (Denmark)
The tidal motion of the ocean water through the ambient magnetic field, generates secondary electric field. This motionally induced electric field can be detected in the sea or inland and has a potential for electrical soundings of the Earth. A first goal of the paper is to gain an understanding of the global distribution of the electric signal due to tidal ocean flow. We simulate the electric signals for two tidal constituents - lunar semidiurnal (M2) and diurnal (O1) tides. We assume a realistic Earth's conductivity model with a surface thin shell and 1-D mantle underneath. Simulations demonstrate that in some coastal regions the amplitudes of the electric field can reach 100 mV/km and 10 mV/km for M2 and O1 tides respectively. The changes of lithosphere resistance produce detectable changes in the tidal electric ...
2006-01-01
Steam turbines for cogeneration plants; Dampfturbinen fuer die Kraft-Waerme-Kopplung
Energy Technology Data Exchange (ETDEWEB)
The demand for cogeneration plants is growing worldwide. For the combination of electricity generation and heat extraction in power stations facilitates an excellent fuel exploitation and makes the operator of the plant independent from external energy suppliers. (orig.)
2006-07-01
Pumped storage plants 20 are a relatively common type.They use a dam to create an upper reservoir ...Some pumped storage plants use the same water turbine and electric generator for both operating periods.That is,
Pumped storage plants are a relatively common type.They use a dam to create an upper reservoir ...Some pumped storage plants use the same water turbine and electric generator for both operating periods.
Heat Cycle Reserch Experimental Program report, FY-84
Energy Technology Data Exchange (ETDEWEB)
The Heat Cycle Research Facility (HCRF) is an experimental binary-cycle facility used to investigate different concepts and/or components for generating electrical power from a geothermal resource. This report briefly desc
1984-09-01
UK PubMed Central (United Kingdom)
The growing use of coal for heating and electric power generation and diesel engines in light duty motor vehicles will increase not only the existing atmospheric concentrations of criteria pollutants...Full Text Available
1983-01-01
Energy Technology Data Exchange (ETDEWEB)
Kawasaki Heavy Industries, Ltd. has developed a gas turbine combined cycle and cogeneration plant computer aided engineering (CAE) system, which creates cycle heat balance automatically on given configurations of gas turbines, heat recovery boilers, steam turbines and auxiliaries. The system can predict the performance of the plant as a function of control set points, loads, process steam requirements and ambient conditions, which enables accurate and fast design of gas turbine combined cycle and cogeneration plants. (author)
1999-04-01
International Nuclear Information System (INIS)
The performance of the gas-jet transport system coupled to the RIKEN gas-filled recoil ion separator GARIS was investigated using 255No produced in the 238U(22Ne, 5n)255No reaction. Alpha particles of 255No separated with GARIS and transported by the gas-jet system were measured with a rotating wheel apparatus for ? spectrometry under low background condition. The high gas-jet efficiencies of about 75% were independent of the recoil ranges of 255No in the gas-jet chamber. The present results suggest that the GARIS/gas-jet system is a promising tool for the next-generation superheavy element chemistry: (1) the background radioactivities of unwanted reaction products are strongly suppressed, (2) the intense beam is absent in the gas-jet chamber and hence the high gas-jet efficiency is achieved, and (3) ...
2008-08-01
New era for coal-based electricity generation in the United States
Energy Technology Data Exchange (ETDEWEB)
In 1970, the Federal Power Commission predicted a fall from 46% to 27% in 1990 as a result of predicted increases in the use of nuclear power. Today, the Department of Energy expects coal to supply about 50% of electricity generation in 1990. About one-eighth of the world's annual hard coal production is used to make electricity in the United States. Power stations in the country used more coal in 1979 than was produced in the whole Western Europe that year. These 405,000,000 tons of coal equivalent were burned in 1257 individual utilities with an aggregate capacity of 235,000 megawatts. There are coal-fired power plants in 43 of the 50 states. Four factors will be most important in shaping the future development of coal-based electricity: prices, conservation, environmental regulations, and national security. The price differential between coal and oil has now reached a level where it is much ...
1980-01-01
Energy Technology Data Exchange (ETDEWEB)
This paper presents a survey on public preferences in SE England for the use of wind, biomass and nuclear power in electricity generation. Using a labelled CE the perceived importance (value) to the public of distance and the energy options' impacts on biodiversity, emissions, land occupation and household cost was explored. Results suggest that impacts, technology name, demographic characteristics, attitudes towards the environment, knowledge and experience with the technologies were significant choice determinants. Considering the current debate about the development of nuclear power and biomass in UK and worldwide, this survey provides an insight into the factors affecting public acceptability
2008-07-01
The world energy consumption in 2001. Statistical yearbook ENERDATA 2002
Energy Technology Data Exchange (ETDEWEB)
Statistical data on the world energy consumption are given to illustrate the following situation in 2001: the deceleration of the world economic growth and the high prices of oil slowed down the progression of the energy consumption: 0,7 % in 2001; stagnation of the gas and oil consumption and strong progression for coal and electricity in 2001; the deceleration for gas marks a strong inflection compared to the past trends. (A.L.B.)
2002-07-01
International Nuclear Information System (INIS)
Comparison of plasma density increase was carried out in outer and inner channels of the interferometer in T-11M tokamak. There were two cases of gas puffing: by outer valve or upper one. Amplitude of difference of the plasma density increase consisted of 9% near the outer valve. Perturbation of the electric potential e?1/Te can have similar value. This perturbation can lead to appearance of the additional losses.
2006-01-01
Monthly energy review, September 1995
Energy Technology Data Exchange (ETDEWEB)
An ``energy snapshot`` article is included on housing characteristics in 1993 (survey of 7,111 households). The rest of the document is divided into: energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, international energy, and appendices (conversion factors, CO2 emission factors from coal, index, glossary).
1995-09-25
Monthly energy review, June 1995
Energy Technology Data Exchange (ETDEWEB)
This is the June report by the Energy Information Administration. The contents of the report include an energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy. Included are appendices containing thermal conversion factors, metric and other physical conversion factors, and carbon dioxide emission factors for coal.
1995-06-01
Diffusion absorption heat pump. Diffusion-Absorptions-Waermepumpe
Energy Technology Data Exchange (ETDEWEB)
The development of a gas-operated diffusion absorption heat pump for the heating of living spaces is described. By various improvement an energy efficiency of the prototypes of 1.5 was achieved. Structural alterations led to a lower overall height and lower production costs. The CFCs used in electric heat pumps were replaced by environmentally neutral ammonia. Compared with conventional gas heating systems, the CO2 output could be reduced by more than 30%. figs., tabs.
1992-02-01
Analysis of a 1200 kV circuit breaker for a gas insulated substation. Final report
Energy Technology Data Exchange (ETDEWEB)
This report describes the work carried out to analyze and design a circuit for use in 1200 kV gas insulated substations. The first part of the project was devoted to a thorough analysis of the requirements for the circuit breaker from the standpoint of the electrical system in which it would operate. A conceptual design was selected and all of the components of the circuit breaker were designed, modeled and verified. Finally a plan was prepared for the construction of a complete circuit breaker.
1985-01-01
British Library Electronic Table of Contents (United Kingdom)
The Sulige gas field and the Yulin gas field are located in the north of the Ordos Basin. Reservoir pressure in the Sulige area is subnormal, whereas reservoirs in the Yulin area have normal hydrostatic pressure. This paper provides an explanation of this difference. The characteristics of reservoir sediment and formation water chemistry in the gas reservoirs of these two areas were analyzed. The results showed that both reservoirs have good sealing ability. Data of numerical simulation showed that tectonic uplift resulted in a great reduction in formation pressure in the northern Ordos Basin during the late Cretaceous period, and the decrease was greater in the Yulin gas field than in the Sulige gas field. However, because the total hydrocarbon-generating intensity of the Sulige area (<24...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Preserving customers` investments in capital goods is one of the strategic market services offered by ABB, and to this end the company has developed project-specific retrofit concepts especially for older power generation plant. A prime example of such a modernization is the Umm Al Nar East (UANE) combined cycle power station in Abu Dhabi, UAE. UANE has two gas turbines of type GT13D, which together generate 140 MW of electrical energy, and heat-recovery boilers which supply steam to a seawater desalination plant with a capacity of 80 million liters of drinking water per day. After almost 20 years in operation, UANE is being modernized. To address the owner`s concerns and minimize plant downtime, ABB has introduced Service, Operation and Rehabilitation (SOR) Key Account Management for Abu Dhabi. In the first phase of the modernization project, the static starting equipment was upgraded and the ...
1998-05-01
The contribution of the DOE`s R&D budget in natural gas to energy price security
Energy Technology Data Exchange (ETDEWEB)
The energy price volatility model suggests that some of the proposed natural gas programs can contribute to energy price stability. The sector most vulnerable to fuel price variations is, of course, the transportation sector. The most effective strategy to achieve energy pace stability is to reduce petroleum consumption in this sector. The natural gas vehicle program is therefore recommended as potentially important and worthy of further consideration. At this point, distinguishing the merits of various subprograms is not feasible. This result farther supports the conclusion that the DOE`s energy R&D portfolio is not efficiently balanced and an increase in oil and gas research should be a high priority. The DOE has responded favorably and has significantly increased its proposed research with the explicit objective of displacing oil in the transportation sector. The enhanced research and development program for energy ...
1992-12-01
Safety gas management system utilizing telephone cable
Energy Technology Data Exchange (ETDEWEB)
This paper describes the safety gas management system utilizing public telephone cables. Buyo Gas Co., Ltd. has installed about 100 governors for exclusive-use or use in the districts to control the gas supply to the consumers. A gas safety management system has been developed. This system consists of a pressure sensor, the terminals of gas leak alarms, and their masters. The features lie in that the system can utilize public cables, is operative at interruption of power service, can correspond to emergency situations, serves to save the cost, and can display the data constantly. For electric facilities in a governor room and the NTT cable service work, sufficient agreement with the possessor is required. In the case of non-utility electric facilities, some restrictions are imposed on the cable work for laying from privately-owned ...
1988-02-10
Electricity on the rig. Part 3 - New electric rig technology
Energy Technology Data Exchange (ETDEWEB)
The use of an SCR-controlled power system on an offshore drilling rig has lead to an increased acceptance of high technology equipment. Such equipment increases drilling productivity, reduces maintenance, and improves reliability. Most new rigs now have AC squirrel cage motors, brushless AC generators, silicon controlled rectifiers, DC motors, and swtichgear and motor starters. Several opportunities for cost reductions in SCR systems, such as improving the power factor, are studied in this paper.
1983-07-01
The challenge of implementing an IRP process in Asia: The case of Hainan Province, China
Energy Technology Data Exchange (ETDEWEB)
Developing a modern electric power sector is necessary for economic growth and development to proceed. Institutions to implement an IRP (integrated resource planning) process do not exist in many countries. Hainan`s economy is growing rapidly with a concomitant increase in electricity demand. This is an ideal time in Hainan`s development to implement an IRP process. The challenge is for Hainan to develop institutions and incentive mechanisms for HEPCO (Hainan Electric Power Co.) to adopt cost-based pricing, run DSM programs, construct renewable generating plants, etc. One proposal is to great a Hainan government-wide IRP committee.
1994-12-31
Energy Technology Data Exchange (ETDEWEB)
System-level-operational testing of the ETX-II test-bed electric vehicle is described and the results discussed. Because the traction battery is a major factor in the performance of an electric vehicle, previously reported work on the sodium-sulfur battery designed for use with the ETX-II is reviewed in detail. Chassis dynamometer performance of the test-bed vehicle met or exceeded design goals and compared reasonably well with SIMPLEV computer modeling results. Areas are identified wherein further work is needed to establish a firmer basis for comparison of the simulation and the observed results.
1993-06-01
Energy Technology Data Exchange (ETDEWEB)
Data on various aspects of the electric power industry in Germany is presented in this article. A map of high voltage transmission lines used by the public utilities is included, which indicates the fuel used at each power station. Data on power generated by fuel used from 1991 to 1996 is given, and additional or new capacity for 1995 to 1999 is also noted. Other tables detail capital investment in public utilities energy input by fuel source, power capacity by utility or private power stations by energy source, utility ownership and electricity demand by consumer. (UK)
1997-09-01
Turbines for the turn of the century
Energy Technology Data Exchange (ETDEWEB)
This article describes how a natural gas-fired combined cycle with increased firing temperature, reduced cooling air usage, improved component efficiencies, and cycle enhancements could achieve a lower heating value plant efficiency of greater than 60%. Today's gas turbine systems feature high fuel-to-electricity efficiencies. Efficiencies, on a lower-heating-value (LHV) basis, for large natural gas-fired combined-cycle systems for the utility market have been demonstrated at 54%. Even though manufacturers will make improvements in the 1990s, efficiency levels will reach a plateau. Cycle innovations and gas turbine design changes will achieve LHV efficiencies in the 60% range for natural gas-fired utility machines.
1994-06-01
Energy Technology Data Exchange (ETDEWEB)
The majority of Brazilian big cities served by conventional railroad systems with routes starting in the center of the URBIS, destinate them the long distances transport of passengers and cargo. Actually, these systems are being transformed to become commuter trains which join a great capacity of transportation to a much lower costs of implantation than subway ones. The most important characteristic of this train, when talking about energy consumption, is the possibility of using different kinds of explosion engines from three cycles: Diesel, mixed (Diesel + Natural Gas), and Otto moved by natural gas, besides the traditional electric traction. The use of natural gas in Otto cycle engines shows itself competitive from the point of view of investments, operational costs and environmental preservation. (author). 10 refs., 1 fig
1995-12-31
Development of commercial high temperature gas-cooled reactor in China
Energy Technology Data Exchange (ETDEWEB)
The high temperature gas-cooled test reactor HTR-10 achieved the first criticality in last December in Institute of Nuclear Energy Technology of Tsinghua University in Beijing. Fuji Electric and Nissho Iwai have a cooperative information exchange agreement on the commercialization of the HTGRs with INET, and held an information exchange meeting in last March in INET. INET has started a study on the modification of the HTR-10 to couple with gas turbine system and a pre-feasibility study on the commercial HTGR under the cooperation with China State Power Company. The experiences and abilities of INET in the field of the HTGR and the aggressive plan for commercialization of the HTGR in China are summarized and discussed. (author)
2001-07-01
Biogas: The green gas? | EurActiv
... Biogas: The green gas? | EurActiv Biogas has become an attractive alternative source of energy in Europe as the renewable fuel ...Graduate Programme Research Analyst Junior Consultant Training Coordinator Post an EU job Biogas: The green gas? Published: 09 April 2010 |...Updated: 06 July 2010 Biogas has become an attractive alternative source of energy in Europe as the renewable fuel serves several policy priorities, ranging from ... Policy Summary Biogas is a renewable energy source that can be used for heating or electricity production. If compressed, it can ...
Energy Technology Data Exchange (ETDEWEB)
The following industrial-scale power station processes are compared with natural gas/light fuel oil heating: Conventional steam generation, steam generation with gas turbine upstream, gas turbine process with low-pressure-waste heat boiler and cogeneration. Industrial gas turbines between 10 and 25 MW are compared with one another; typical boilers and industrial turbines are described. CO{sub 2} and NO{sub x} emissions are indicated. The steam turbines used are the efficient and robust turbines used in industry, wherever possible they are built as single-line plant with the gas turbine. (orig.) [Deutsch] Es werden folgende Industriekraftwerksprozesse mit Erdgas-Leichtoelfeuerung verglichen: Konventioneller Dampfprozess, Dampfprozess mit Vorschaltgasturbine, Gasturbinenprozess mit ND-Abhitzekessel und Kombianlage. Die Industriegasturbinen ...
1994-12-31
An overview of PETC`s gas-to-liquids technology R&D Program
Energy Technology Data Exchange (ETDEWEB)
The overall goal of the Gas-to-Liquids Program at the U.S. Department of Energy`s Pittsburgh Energy Technology Center (PETC) is to develop technologies for the production of hydrocarbon fuels and premium chemicals from light alkane gases. PETC`s current Gas-to-Liquids Program comprises the development of four primary advanced conversion technologies, namely, partial oxidation, oxidative coupling, oxyhydrochlorination, and novel conversion processes. Based on the current state of development, it can be concluded that, in the near future, one or more of these technologies will reach proof-of-concept demonstration. Oxyhydrochlorination is the most advanced direct conversion technology, and the synthesis of lower cost methyl chloride from natural gas would impact several commercial technologies that utilize methyl chloride as an intermediate to high value products. Technology development for the partial oxidation of methane to ...
1995-04-01
Coal-fired methane reforming for power and chemical plants
Energy Technology Data Exchange (ETDEWEB)
The increasing price differential between natural gas and coal will create a demand for technology that can allow the displacement of natural gas with coal in power plants. Coal gasification is the standard approach suggested to allow coal to displace natural gas. However, the relatively high capital investment required for coal gasification will require fuel cost differentials higher than those anticipated in the near term before coal gasification replaces natural gas. One way of achieving shorter term displacement of natural gas by coal would be to develop technology that would allow coal to be used as the heat source for the endothermic reforming of natural gas. In a natural gas-fired combined cycle power plant, the endothermic heat of reforming, which would be provided by coal combustion, is recovered in the combined-cycle. Therefore, ...
1996-12-31
Energy usage for cotton ginning in Australia
Energy Technology Data Exchange (ETDEWEB)
This paper reported on a study that evaluated the energy consumption of cotton gins used in Australia. The average electricity use is 52.3 kWh per bale. In practicality, the electricity consumption for different gins is correlated linearly with the bale numbers produced. The cost of electricity is therefore important in cotton ginning operations. The power factor in all the gins monitored in this study was greater than 0.85. The study showed that the use of gas dryers was highly influenced by the cotton moisture and regulated drying temperature. In general, electricity and gas consumption comprised 61 and 39 per cent of total energy use respectively. The study showed that 60.38 kg of carbon dioxide are emitted for ginning each bale of cotton. This paper described a newly developed method for monitoring the energy performance in cotton gins. Detailed monitoring ...
2010-07-01
Energy Technology Data Exchange (ETDEWEB)
The State of the Espirito Santo will become until the end of 2008, one of the main producers and natural gas exporters of Brazil, where, according to PETROBRAS, the State will produce about 20 million /day m{sup 3}, what it will go to contribute significantly for reduction of the dependence of the Bolivian gas, and still to give support to the natural gas sector in Brazil. The Intention of this work, is to identify proposals so that it has left of the gas produced in the State of the Espirito Santo, has a differentiated price. It does not make sensible the State to pay for the gas that is removed in its proper territory the same price that paid Sao Paulo for the gas that consumes imported of national Bolivia. With the markdown of the gas the State will be able to attract investments of great transport, to generate job ...
2008-07-01
Energy Technology Data Exchange (ETDEWEB)
The European gas market is continuing to expand due to increased industrial, domestic and power generation demand. As a result of this demand, and the trend toward liberalization of the market, the need for storage of gas is also increasing. One key segment of the large scale storage of gas is underground storage, either in partially depleted gas or oil fields, naturally occurring caverns, aquifers and salt cavities. In most cases the gas produced after storage requires conditioning to meet the water of hydrocarbon dew point specification of the gas transmission system. For that reason export gas from storage will require gas conditioning in order to meet pipeline specifications. Adsorption as a feasible and reliable process will be presented in detail and especially in regards to hydrocarbon ...
2000-07-01
EPRI-USDOE COOPERATIVE AGREEMENT: COFIRING BIOMASS WITH COAL
Energy Technology Data Exchange (ETDEWEB)
The entire Electric Power Research Institute (EPRI) cofiring program has been in existence of some 9 years. This report presents a summary of the major elements of that program, focusing upon the following questions: (1) In pursuit of increased use of renewable energy in the US economy, why was electricity generation considered the most promising target, and why was cofiring pursued as the most effective near-term technology to use in broadening the use of biomass within the electricity generating arena? (2) What were the unique accomplishments of EPRI before the development of the Cooperative Agreement, which made developing the partnership with EPRI a highly cost-effective approach for USDOE? (3) What were the key accomplishments of the Cooperative Agreement in the development and execution of test and demonstration programs-accomplishments which significantly furthered the ...
2001-09-01
1988 EEI (Edison Electric Institute) power directory
Energy Technology Data Exchange (ETDEWEB)
Generated annually from the Edison Electric Institute's POWER STATISTICS Data Base, the EEI Power Directory provides state-by-state data on all utility-owned steam-electric plants in the US. The 1988 directory contains the following information for approximately 2500 units located at 1000 generating sites around the country: unit age, capacity, fuel type, and operating status. In addition, solid waste disposal methods for fly ash, bottom ash, and sludge are covered for approximately 1500 US coal-fired units. The directory contains a listing of more than 800 environmental managers and key environmental staff at over 300 utilities, with names, addresses, and telephone numbers. Special indices list plants and utility owner-operators.
1988-05-01
Materials choices for the advanced LWR steam generators
International Nuclear Information System (INIS)
Current light water reactor (LWR) steam generators have been affected by a variety of corrosion and mechanical damage degradation mechanisms. Included are wear caused by tube vibration, intergranular corrosion, pitting, and thinning or wastage of the steam generator tubing and accelerated corrosion of carbon steel supports (denting). The Electric Power Research Institute (EPRI) and the Steam Generator Owners Groups (I, II) have sponsored laboratory and field studies to provide ameliorative actions for the majority of the damage forms experienced to date. Some of the current corrosion mechanisms are aggravated or caused by unique materials choices or materials interactions. New materials have been proposed and at least partially qualified for use in replacement model steam generators, including an advanced LWR design. In so far as possible, the materials choices for the advanced LWR ...
1987-11-15
Cleaning of flue gases from cupola and electric steel melting furnaces in ''Ural'' rotoclones
Energy Technology Data Exchange (ETDEWEB)
A highly effective and economical apparatus was developed by the All-Union Scientific Research Institute for Energy and Nonferrous Metallurgy for cleaning waste gases from cupola and electric arc steel melting furnaces --- the ''Ural'' rotoclone, which has been successfully introduced in many enterprises. Research results are presented for the efficiency of operation of these aggregates on equipping them on cupola and electric furnaces. With a 2 kPa aerodynamic resistance of the rotoclone the flue gas of the cupola furnace is cleaned to the sanitary standard. Highly effective collection of sublimates and aerosols from the electric arc furnace takes place with a ''Ural'' rotoclone aerodynamic resistance
1981-01-01
Energy Technology Data Exchange (ETDEWEB)
The paper industry needs alternative waste disposal methods rather than dumping sites. The combustion properties of these waste materials make them suitable for thermal disposal. A process has been developed in which the waste materials are burnt on an oscillating bar grate without supplying external energy. Electrical energy and process steam are generated while small amounts of a sintered slag remain behind. (orig.).
1991-05-01
Characterization of eddy current probes used in steam generator tubes inspection
International Nuclear Information System (INIS)
In in-service inspection of steam-generator tubes, the need for reproducibility of the measurement results and for comparison of these results over two successive inspections has led EDF to specify the main characteristics of the eddy-current probes and to design equipment to measure them. This equipment is presented here and the electrical and magnetic results are correlated with those obtained by testing tubes with reference defects.
1985-02-01
Characterization of Eddy Current probes used in steam generator tubes inspection
International Nuclear Information System (INIS)
In in-service inspection of steam-generator tubes, the need for reproducibility of the measurement results and for comparison of these results over two successive inspections has led EDF to specify the main characteristics of the Eddy-Current probes and to design equipment to measure them. This equipment is presented here and the electrical and magnetic results are correlated with those obtained by testing tubes with reference defects. 5 refs.
1985-02-01
Implications of high temperature superconductors for power generation
International Nuclear Information System (INIS)
Superconducting generators for high power applications have been of interest for a number of years. Superconducting generators using low temperature superconductors (LTS) have been manufactured to produce up to 20 MW of electrical power and have been configured in either synchronous alternators which have an AC output that may be subsequently rectified to produce DC and homopolar generators which produce low voltage DC. Typically these generators require scrupulous attention to vacuum integrity for cryogenic insulation at 4.2K and tend to be somewhat fragile because of extensive thermal and magnetic shields that are not required in conventional power generators. Recently, high purity aluminum composites have been developed for a high power AC generator that is cooled by cryogenic hydrogen at 21K. This aluminum generator ...
1991-08-03
Energy Technology Data Exchange (ETDEWEB)
In order to serve for efficient energy utilization and environmental improvement in the Republic of Vietnam, a 'Model project to reduce electric power consumption at cement burning plant' has been implemented. This paper summarizes the achievements. This project is intended to add an advanced, matured and reliable electric power generation facility using cement waste heat to the existing cement plant in Vietnam to produce steam and generate power by utilizing the waste heat generated from the preheating process in the burning plant. The present project has performed the detailed designing on the piping, electric facilities and instrumentation based on the basic agreement on the project. Fabrication of the piping has been executed by the Vietnam side. Valves and electric devices were procured and transported, including those ...
2002-03-01
Development of Mainshaft High Speed Cylindrical Roller Bearings for Gas Turbine Engines.
This combined analytical and experimental program is aimed at generating a manual that will permit the design of 3.0 MDN cylindrical roller bearings. The roller bearing analysis will be correlated with the results from a series of bearing tests designed t...
1977-01-01
UK PubMed Central (United Kingdom)
Charge reduction electrospray mass spectrometry (CREMS) reduces the charge states of electrospray-generated ions, which concentrates the ions from a protein into fewer peaks spread over a larger...Full Text Available
2005-11-01
UK PubMed Central (United Kingdom)
BackgroundWith the phasing out of ozone-depleting substances in accordance with the United Nations Montreal Protocol, phosphine remains as the only economically viable fumigant for...Full Text Available
Atomic-scale insight and design principles for turbine engine thermal barrier coatings from theory
UK PubMed Central (United Kingdom)
To maximize energy efficiency, gas turbine engines used in airplanes and for power generation operate at very high temperatures, even above the melting point of the metal alloys from which they are...Full Text Available
2011-04-05
Rethinking development assistance for wind power
Energy Technology Data Exchange (ETDEWEB)
Electricity generation from wind turbines is now cost competitive for grid and off-grid applications in many developing regions, and close to competitive in others. Wind resources could generate thousands of megawatts of badly-needed power in Asia, North Africa, and Latin America. Barriers to penetrating power generation markets remain, however, including unequal access to investment capital, energy price and other market distortions, and often weak institutions for commercializing new technologies. Recognizing the potential economic and environmental benefits of wind power, bilateral and multilateral assistance organizations have for several years offered financial and technical assistance to promote its diffusion. Based on this experience and assistance for other renewable electric technologies, lessons and recommendations can be drawn regarding how assistance could more ...
1995-12-31
Climate change/variability implications on hydroelectricity generation in the Zambezi River Basin
British Library Electronic Table of Contents (United Kingdom)
The study has analysed the effects of various factors on hydroelectric power generation potential to include climate change/variability, water demand, and installation of proposed hydroelectric power schemes in the Zambezi River Basin. An assessment of historical (1970?2000) power potential in relation to climate change/variability at existing hydro electric power schemes(Cahora Bassa, Kariba, Kafue Gorge and Itezhi-Tezhi) in the Zambezi River Basin was conducted. The correlation of hydroelectric power potential with climate change/variability aimed at observing the link and extent of influence of the latter on the former was investigated. In order to predict the future outlook of hydro electric power potential, General Circulation Models (GCM) were used to generate projected precipitation...
2011-01-01
IEA Greenhouse Gas R and D Programme annual report 1998
Energy Technology Data Exchange (ETDEWEB)
The report outlines the role of the IEA Greenhouse Gas R and D Programme, gives details of participants and of publications and summarises achievements of 1998. A successful conference on Greenhouse Gas Control Technologies was held in Interlaken, Switzerland. Technical studies reported include novel power generation concepts for removing carbon dioxide prior to or after combustion, using seawater for CO{sub 2} capture, investigating carbon dioxide sequestration in conjunction with enhanced coalbed methane recovery and applying retrofitting to power plants and to offshore oil and gas platforms. Systems studies taking a broader view include investigating the potential for combined energy systems (power generation with district heating, power with district cooling etc.) to reduce CO{sub 2} abatement cost, studies on the LNG/power generation fuel cycle, assessing ...
1999-07-01
Cheng cycle cogeneration system; Cheng cycle system cogeneration setsubi
Energy Technology Data Exchange (ETDEWEB)
This paper presents the Cheng cycle system featured by variable heating/generation ratio for effective operation of cogeneration systems (CGS). In this system, a superheater and reheating burner are added to an exhaust heat recovery (EHR) boiler for conventional gas turbine CGSs, while additional injection steam piping is attached to a gas turbine. Steam is injected through manifolds mounted on the periphery of a combustion chamber, and hot gas mixture of steam and air in a combustion chamber is expanded in a turbine and converted to motive power. This technology thus can improve efficiency and output power, and can operate variably CGSs corresponding to heating and generation demands. This technology has been promoted by introducing the technology of middle class Cheng cycle CGS with 4MW class gas turbine from IPT Co., U.S.A. The first system of 6400 kW is now ...
1996-03-29
Energy Technology Data Exchange (ETDEWEB)
Sandia National Laboratories is currently involved in the optimization of a Plane Shock Generator Explosive Lens (PSGEL). The PSGEL component consists of a detonator, explosive, brass cone and tamper housing. The purpose of the PSGEL component is to transmit a plane shock wave through the 4340 steel bulkhead (wave separator) which has a ferro-electric (PZT)ceramic disk attached to the opposite surface of the steel bulkhead. The planar shock wave depolarizes the PZT 65/35 ferro-electric ceramic to produce an electrical output. One aspect of the optimization program involves the possible replacement of 4340 steel with PH13-8Mo steel for the bulkhead. These materials, as well as the PZT 65/35 ferro-electric ceramic and the brass for the cone, required the stock characterization with respect to Hugoniot parameters. The work presented here gives the shock Hugoniot values for these four ...
1994-03-01
Hydroelectric and pumped storage plants
Energy Technology Data Exchange (ETDEWEB)
All power plant engineers face the problem of peak power demands. Pumped storage plants are used to generate peak load power by pumping up water utilizing off-peak energy of hydrothermal and thermonuclear plants. This is the first accessible text/reference to cover hydroelectric power generation with emphasis on engineering to meet peak power demands by means of pumped storge plants, tidal power plants, and low head power generation. Text covers hydrology, mechanical and electrical equipment, accessories such as penstocks and valves, and civil engineering considerations. Contains descriptions of several existing plants. Includes 200 diagrams and 50 photographs.
1989-01-01
Hydroelectric and pumped storage plants
Energy Technology Data Exchange (ETDEWEB)
All power plant engineers face the problem of peak power demands. Pumped storage plants are used to generate peak load power by pumping up water utilizing off-peak energy of hydrothermal and thermonuclear plants. This is a reference to cover hydroelectric power generation with emphasis on engineering to meet peak power demands by means of pumped storage plants, tidal power plants, and low head power generation. Text covers hydrology, mechanical and electrical equipment, accessories such as penstocks and valves, and civil engineering considerations. Contains descriptions of several existing plants. Includes 200 diagrams and 50 photographs.
1988-01-01
Engineering study on steam storage power generation. System screening and efficiency
Energy Technology Data Exchange (ETDEWEB)
Large scale steam storage power generation, one of the new energy storage systems for the future of inflexible electric power sources consisting of nuclear and coal power plants has been studied on the subjects of the systems to be attached to coal and nuclear power units, of the definition of storage efficiency and of the vertical steam storage vessel technology. Steam storage power generation may be hopeful for its higher efficiency similarly defined as of pumped storage plants while high temperature heat storage and the internal structure of large vertical steam storage vessel (accumulator) need to be developed.
1981-11-01
Engineering study on steam storage power generation
International Nuclear Information System (INIS)
Large scale steam storage power generation, one of the new energy storage systems for the future of inflexible electric power sources consisting of nuclear and coal power plants has been studied on the subjects of the systems to be attached to coal and nuclear power units, of the definition of storage efficiency and of the vertical steam storage vessel technology. Steam storage power generation may be hopeful for its higher efficiency similarly defined as of pumped storage plants while high temperature heat storage and the internal structure of large vertical steam storage vessel (accumulator) need to be developed. (author).
1981-01-01
Application of power system stabilizer at Bandar-Abbas power station
Energy Technology Data Exchange (ETDEWEB)
System instability as result of high power generation of one of the largest plants of the Iranian electric power grid prevented the plant to be fully utilized. PSSs were installed on the generating units of the power station, to improve its small signal stability, and enhance the stable generation limit. Domain separation and pole assignment techniques were applied for the PSS design. Several field tests were also carried out to verify its effectiveness. This paper presents the PSS tuning procedure, including the design criteria and some of the field test results.
1994-08-01
Giant gas field of northern West Siberia
Energy Technology Data Exchange (ETDEWEB)
The 66 fields discovered since the 1960s in the northern West Siberian basin contain at least 22 trillion m/sup 3/ (777 tcf) of proved gas, almost one-third of the world's reserves. Half of these fields are giants (> 85 billion m/sup 3/ or 3000 bcf of reserves). These include the largest and second-largest gas fields in the world-Urengoy (8.099 trillion m/sup 3/ or 286 tcf of gas) and Yamburg (4.81 trillion m/sup 3/ or 170 tcf of gas)-as well as most of the other ten largest gas fields in the world. The West Siberian basin occupies a 3.4-million km/sup 2/ (1.31-million mi/sup 2/) arctic lowland immediately east of the Ural Mountains, extending north under the Kara Sea. It is a composite basin, with Mesozoic-Cenozoic basin fill on top of a Paleozoic basin that overlies a crystalline Archean-Proterozoic framework. The productive zones in the northern basin are principally ...
1986-06-01
Ion-plasma nitriding of the alloyed steel using a low pressure arc plasma generator
International Nuclear Information System (INIS)
A study is made into microhardness and structure of coatings on various system steels (37G2S, 25Kh5M, R6M5), obtained by ion nitriding in a low pressure (10"-"1 Pa) arc discharge plasma. A comparison of properties is accomplished for steels nitrided in an arc gas discharge and in a furnace. It is stated that ion-plasma nitriding in an arc gas plasma generator is an efficient method of alloy steels hardening which allows changing the structure and increasing the hardness of a surface layer up to rather great depth
2006-12-01
The availability of technology for reducing SO2 emissions from coal-fired steam generators using flue gas desulfurization (FGD) systems is discussed. Foreign and domestic lime, limestone, double alkali, magnesium slurry, and Wellman-Lord FGD systems are described, and the design parameters and operating experiences are discussed. Steps that have been taken to achieve high system operability are discussed. Also, disposal of FGD system wastes is discussed briefly.
1978-03-01
Electrochemical power generation apparatus and methods
Energy Technology Data Exchange (ETDEWEB)
Apparatus and methods are described for generating heat and electricity from the consumption of a variety of aluminum products. The method consists of (A) a reaction chamber containing an aqueous electrolyte solution and adapted for introduction therein of aluminum pieces of various shapes and sizes up to a certain maximum predetermined size and for effecting a chemical reaction between said aqueous electrolyte and said aluminum pieces yielding aluminum hydroxide and an intermediate reactant; (B) means for feeding said aluminum pieces into said reaction chamber in small quantities upon demand; (C) means for removing the heat generated in said chamber as a result of said reaction; (D) means for removing said aluminum hydroxide reaction product; and (E) means for oxidizing said intermediate reactant in an electrochemical cell, thereby generating electrical energy. The intermediate ...
1981-03-03
Electrochemical power generation
Energy Technology Data Exchange (ETDEWEB)
Apparatus and methods for generating heat and electricity from the consumption of a variety of aluminum products comprise: (A) a reaction chamber containing an aqueous electrolyte solution and adapted for introduction therein of aluminum pieces of various shapes and sizes up to a certain maximum predetermined size and for effecting a chemical reaction between said aqueous electrolyte and said aluminum pieces yielding aluminum hydroxide and an intermediate reactant; (B) means for feeding said aluminum pieces into said reaction chamber in small quantities upon demand; (C) means for removing the heat generated in said chamber as a result of said reaction; (D) means for removing said aluminum hydroxide reaction product; and (E) means for oxidizing said intermediate reactant in an electrochemical cell, thereby generating electrical energy. The intermediate reactant is preferably hydrogen ...
1983-01-18
Modeling of lean premixed combustion in stationary gas turbines
Energy Technology Data Exchange (ETDEWEB)
Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The model is also applied to ...
1999-07-01
Feasibility study on Bobovdol thermal power plant upgrading project
Energy Technology Data Exchange (ETDEWEB)
A survey has been made in relation with the improvement project intended of energy conservation, and reduction of global warming gas emission at the Bobovdol thermal power plant located in the suburb of Sofia, the capital of the Republic of Bulgaria. The existing Bobovdol power plant having a total capacity of 630 MW with three generators is a coal burning thermal power plant having been used already for 23 to 27 years, hence over-aged. The survey has discussed an improvement project of scrap-and-build type to make the plant a high-efficiency gas combined cycle power plant using gas turbines. The project calls for building 210-MW gas combined power generation facilities having 70-MW gas turbines, one each in three stages in 2007, 2012 and 2017. As a result of the discussions, the fuel consumption reducing rate was found to reach 37.99%, ...
2001-03-01
Technical input to NAECA rulemaking for gas-fired ranges. Topical report, January-July 1994
Energy Technology Data Exchange (ETDEWEB)
The report presents the results of a Gas Research Institute (GRI) program to evaluate the technical and economic aspects of design options proposed by the U.S. Department of Energy (DOE) for reducing the energy consumption of residential ranges and ovens as mandated by the National Appliance Energy Conservation Act (NAECA) of 1987. The study shows that none of the proposed DOE design options are justified except electric ignition for stand-alone cooktops, based on life-cycle costs, loss of consumer utility, safety, technical considerations, or food quality considerations. An individual range uses so little gas during the year (approximately $14/year for a self-cleaning range) that it is difficult to justify any design modification, since the cost of even a simple modification could not be recovered on the basis of gas saved.
1994-07-01
The developments of fields in deep waters (5000 ft and more) is a common occurrence. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas-oil-and water possibly along with sand, hydrates, and wax...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.
1981-01-01
The developments of oil and gas fields in deep waters (5000 ft and more) will become more common in the future. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas-oiland water possibly along wi...
2007-01-01
Flue gas desulfurization wastewater treatment primer
Purge water from a typical wet flue gas desulfurization system contains myriad chemical constituents and heavy metals whose mixture is determined by the fuel source and combustion products as well as the stack gas treatment process. A well-designed water treatment system can tolerate upstream fuel and sorbent arranged in just the right order to produce wastewater acceptable for discharge. This article presents state-of-the-art technologies for treating the waste water that is generated by wet FGD systems. 11 figs., 3 tabs.
2009-03-15
Energy Technology Data Exchange (ETDEWEB)
During thirty years the techniques used for sensing the environment have changed dramatically. This paper describes the latest generation of sensors available. This new generation of sensors includes those two most critical gas sensors for methane and carbon monoxide and new sensors for airflow and air temperature. When these sensors are combined with the new sensors for machine condition monitoring it forms the heart of the Sentex system. 2 figs.
1989-06-01
Optimizing electrical load pattern in Kuwait using grid connected photovoltaic systems
International Nuclear Information System (INIS)
Grid connected photovoltaic systems is one of the most promising applications of photovoltaic systems. These systems are employed in applications where utility service is already available. In this case, there is no need for battery storage because grid power may be used to supplement photovoltaic systems (PV) when the load exceeds available PV generation. The load receives electricity from both the photovoltaic array and the utility grid. In this system, the load is the total electrical energy consumption. The main objective of the present work is to optimize the electrical load pattern in Kuwait using grid connected PV systems. In this situation, the electric load demand can be satisfied from both the photovoltaic array and the utility grid. The performance of grid connected photovoltaic systems in the Kuwait climate has been evaluated. It was found that the peak load matches the ...
2004-03-01
Energy Technology Data Exchange (ETDEWEB)
The hydro-generators suffer during its operative useful life a combination of stresses of nature thermal, electric, mechanics and environmental. With the time, they are going losing the capacity to support those stresses and the power plants suffer, more and more frequently, undesirable stops for repair services and maintenance. In function of the high costs incurred with these stopped, the operation of the power plant can be economically impracticable. That unavailability of the generation for the electric system, it results in reduction of the reliability, burdening the politics of load ruling. The re-potentiation is a proposal that seeks to extend the useful life of hydro-generators, at the same time that it try to rescue the reliability and the readiness of the plant, with larger power. The power increase is usually made possible, or for the surplus of the hydro resources in ...
1996-07-01
Energy Technology Data Exchange (ETDEWEB)
The demonstration test of a power system stabilizer, employing a fuzzy theory, in the two hydroelectric power stations of Kyusyu Electric Power Co., Inc. is described. The PSS inputs auxiliary signals to the automatic voltage regulator (AVR) of a generator and generates an electric torque in the direction opposite to the operating direction of a generator to enhance the damping effect and improve the system stability. Usually, the change in the slide information of a generator is detected, and the phase adjustment is performed so that the damping is the optimum value. However, since the damping is optimized in the specific system state, no complete damping may be obtained when the system state is changed. A fuzzy theory was thus applied for the control operation part. In a secondary fuzzy PSS, the velocity and acceleration were calculated from the slide ...
1997-03-01
Energy Technology Data Exchange (ETDEWEB)
`De Groote Wielen` is going to be a newly built area of the municipality Den Bosch, Netherlands. In the period 1998-2011 circa 6,200 houses and 39,000 m{sup 2} will be built. Under the authority of the municipality Den Bosch CE compared a few energy supply options. Attention is paid to three different forms of energy supply: traditional supply of natural gas and electricity, supply of heat (produced by cogeneration gas engines and collective electrical heat pumps) and electricity, and supply of electricity by means of individual heat pumps for each house. Two levels of the energy performance standard are taken into account: 1.2 and 1.0. Also costs and resulting emissions of those options are compared. Next to a quantitative discussion, also the qualitative consequences of the three concepts are dealt with. The most important quantitative consequence concerns the ...
1996-07-01
Thin-film solar cells on flexible, lightweight, space-qualified substrates provide an attractive approach to fabricating solar arrays with high mass-specific power. A polycrystalline chalcopyrite absorber layer is among the new generation of photovoltaic device technologies for thin film solar cells. At NASA Glenn Research Center we have focused on the development of new single-source precursors (SSPs) for deposition of semiconducting chalcopyrite materials onto lightweight, flexible substrates. We describe the syntheses and thermal modulation of SSPs via molecular engineering. Copper indium disulfide and related thin-film materials were deposited via aerosol-assisted chemical vapor deposition using SSPs. Processing and post-processing parameters were varied in order to modify morphology, stoichiometry, crystallography, electrical properties, and optical properties to optimize device quality. Growth at atmospheric pressure in a horizontal ...
2008-01-01
Prototype exposure chamber of radon for animal experiments
Energy Technology Data Exchange (ETDEWEB)
To evaluate a dose conversion factor from the `Working Level of Month` (WLM) of radon to the absorbed dose (mGy), the quality of radon and its progeny was assessed, and exposures controlled for each deposition region were planed as follows: 1) exposure of radon gas to the entire respiratory tract, 2) exposure of `unattached` fractions to the upper respiratory tract, 3) exposure of `attached` fractions onto ultrafine particles to the deep lung, 4) exposure of `attached` fractions onto fine particles to the lower respiratory tract, 5) exposure of `attached` fractions onto coarse particles to the upper respiratory tract. In this preliminary study, a prototype exposure system of radon and its progeny for small rodents was designed. A whole body exposure chamber with a volume of about 0.5 m{sup 3} was used, which it held 20 rats. The aging and mixing chamber separated by the exposure chamber had a volume of about 1 m{sup 3}. As career aerosols of radon progeny, carnauba ...
1998-12-31
Market leadership by example: Government sector energy efficiency in developing countries
Energy Technology Data Exchange (ETDEWEB)
Government facilities and services are often the largest energy users and major purchasers of energy-using equipment within a country. In developing as well as industrial countries, government ''leadership by example'' can be a powerful force to shift the market toward energy efficiency, complementing other elements of a national energy efficiency strategy. Benefits from more efficient energy management in government facilities and operations include lower government energy bills, reduced greenhouse gas emissions, less demand on electric utility systems, and in many cases reduced dependence on imported oil. Even more significantly, the government sector's buying power and example to others can generate broader demand for energy-efficient products and services, creating entry markets for domestic suppliers and stimulating competition in providing high-efficiency products and ...
2002-05-20
Energy Technology Data Exchange (ETDEWEB)
The significant and rapid reduction of greenhouse gas emissions is recognized as necessary to mitigate the potential climate effects from global warming. The postcombustion capture (PCC) and storage of carbon dioxide (CO{sub 2}) produced from the use of fossil fuels for electricity generation is a key technology needed to achieve these reductions. The most mature technology for CO{sub 2} capture is reversible chemical absorption into an aqueous amine solution. In this study the results from measurements of the CO{sub 2} absorption capacity of aqueous amine solutions for 76 different amines are presented. Measurements were made using both a novel isothermal gravimetric analysis (IGA) method and a traditional absorption apparatus. Seven amines, consisting of one primary, three secondary, and three tertiary amines, were identified as exhibiting outstanding absorption capacities. Most have a number of structural features in ...
2009-08-15
Energy Technology Data Exchange (ETDEWEB)
This article gives an account of the recent development of light water reactors new concepts in the world. Different projects are being studied. The CE80+ from Combustion Engineering (CE) is a 1350 MWe-PWR-type reactor whose primary circuit is confined in a spherical metallic containment. This reactor was certified by NRC (national regulatory commission) in mid-1996. The APWR (advanced pressurized water reactor) is developed by MHI (Mitsubishi heavy industries) in a collaboration with Westinghouse, this PWR-type reactor fitted with 4 loops derived from the SP90 model that was developed by Westinghouse during the eighties. 2 units of ABWR (advanced boiling water reactor) were commissioned in Japan in 1996 and 1997, ABWR was certified by NRC in mid-1996. The BWR90+ is developed by ABB-atom (Sweden) and it represents a cautious advanced version of the BWR75. Passive reactors are reactors that rely only on potential energy (compressed gas, gravitational flow or ...
2001-07-01
Multiphase reacting flow modeling of singlet oxygen generators for chemical oxygen iodine lasers.
Energy Technology Data Exchange (ETDEWEB)
Singlet oxygen generators are multiphase flow chemical reactors used to generate energetic oxygen to be used as a fuel for chemical oxygen iodine lasers. In this paper, a theoretical model of the generator is presented along with its solutions over ranges of parameter space and oxygen maximizing optimizations. The singlet oxygen generator (SOG) is a low-pressure, multiphase flow chemical reactor that is used to produce molecular oxygen in an electronically excited state, i.e. singlet delta oxygen. The primary product of the reactor, the energetic oxygen, is used in a stage immediately succeeding the SOG to dissociate and energize iodine. The gas mixture including the iodine is accelerated to a supersonic speed and lased. Thus the SOG is the fuel generator for the chemical oxygen iodine laser (COIL). The COIL has important application for both military ...
2008-08-01
The efficiency of coal-fired combined-cycle powerplants
Energy Technology Data Exchange (ETDEWEB)
Concepts involving combined gas-turbine/steam-turbine power-generation plants, in which the fuel gas for the gas turbine is produced via the gasification of coal, are now extremely advanced. This technology already permits efficiencies of around 50% current development targets view 65% as achievable. In conventional technology, efficiencies are tied to conditions, such as air and cooling-water temperatures, at the particular location. In combined-cycle power plants, the properties of the fuel coal also play an important part. There are, in face, coals which can be more advantageously used in a combined-cycle power plant than in a conventional one. These differences, combined with advantageous concepts for coal-fired combined-cycle power-generating plants, are presented and analyzed. Particular attention is devoted to individual losses occurring at coal conversion, thermodynamic ...
1996-12-01
British Library Electronic Table of Contents (United Kingdom)
We have demonstrated that, with simple pH adjustment, volatile drugs such as methamphetamine, amphetamine, 3,4-methylenedioxymethamphetamine (MDMA), ketamine, and valproic acid could be analyzed rapidly from raw biofluid samples (e.g. urine and serum) without dilution, or extraction, using atmospheric pressure ionization. The ion source was a variant type of atmospheric pressure chemical ionization (APCI) that used a dielectric barrier discharge (DBD) to generate the metastable helium gas and reagent ions. The sample solution was loaded in a disposable glass pipette, and the volatile compounds were purged by nitrogen gas to be reacted with the metastable helium gas. The electrodes of the DBD were arranged in such a way that the generated glow discharge was confined within the discharge tub...
2009-01-01
The goal of this project is to demonstrate that, by combining state-of-the-art technology, highly efficient plant operation and maintenance capabilities and by-product gypsum sales, significant reductions of SO{sub 2} emissions can be achieved at approximately one-half the life cycle cost of a conventional Flue Gas Desulfurization (FGD) system. Further, this emission reduction is achieved without generating solid waste and while minimizing liquid wastewater effluent. Basically, this project entails the design, construction and operation of a nominal 600 MWe AFGD facility to remove SO{sub 2} from coal-fired power plant flue gas at the Northern Indiana Public Service Company`s Bailly Generating Station.
1994-08-01
Energy Technology Data Exchange (ETDEWEB)
The challenge for truck engine product engineering is not only to fulfill increasingly stringent emission requirements, but also to improve the engine's economical viability in its role as the backbone of our global economy. While societal impact and therefore emission limit values are to be reduced in big steps, continuous improvement is not enough but technological quantum leaps are necessary. The introduction and refinement of electronic control of all major engine systems has already been a quantum leap forward. Maximizing the benefits of these technologies to customers and society requires full use of parameter optimization and other enabling technologies. The next big step forward will be widespread use of exhaust aftertreatment on all transportation related diesel engines. While exhaust gas aftertreatment has been successfully established on gasoline (Otto cycle) engines, the introduction of exhaust aftertreatment especially for heavy-duty diesel ...
2003-08-24
Optimized hydrogen piston engines
Energy Technology Data Exchange (ETDEWEB)
Hydrogen piston engines can be simultaneously optimized for improved thermal efficiency and for extremely low emissions. Using these engines in constant-speed, constant-load systems such as series hybrid-electric automobiles or home cogeneration systems can result in significantly improved energy efficiency. For the same electrical energy produced, the emissions from such engines can be comparable to those from natural gas-fired steam power plants. These hydrogen-fueled high-efficiency, low-emission (HELE) engines are a mechanical equivalent of hydrogen fuel cells. HELE engines could facilitate the transition to a hydrogen fuel cell economy using near-term technology.
1994-05-10
Multilayer ultra high gradient insulator technology
Energy Technology Data Exchange (ETDEWEB)
We are investigating a novel insulator concept which involves the use of alternating layers of conductors and insulators with periods less than 1 mm. These structures perform many times better (about 1.5 to 4 times higher breakdown electric field) than conventional insulators in long pulse, short pulse, and alternating polarity applications. We present our ongoing studies investigating the degradation of the breakdown electric field resulting from surface roughness, the effect of gas pressure, and the performance of the insulator structure under bi-polar stress. Further, we present our initial modeling studies.
1998-03-27
Consultations - Department of Energy and Climate Change
... Areas of Consultation: All Areas About DECC Bioenergy Carbon capture & storage Carbon Reduction Commitment Climate Change Agreements CRC energy efficiency scheme Development, consents and planning reform Electricity Electricity network Emissions Emissions trading Energy markets Energy network Energy security Feed-in Tariffs Fuel poverty Funding and support Gas Governance Green Deal Hydroelectricity International climate change International energy Legislation Low-carbon Microgeneration News Nuclear Oil Renewable energy Saving energy and CO2 Site Wide Footer Smart ...
Energy Technology Data Exchange (ETDEWEB)
A complex modulated structure is described for reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures. 2 figs.
1996-04-09
Energy Technology Data Exchange (ETDEWEB)
This report documents the development and use of the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The model, developed in a spreadsheet format, estimates the full fuel- cycle emissions and energy use associated with various transportation fuels for light-duty vehicles. The model calculates fuel-cycle emissions of five criteria pollutants (volatile organic compounds, carbon monoxide, nitrogen oxides, sulfur oxides, and particulate matter measuring 10 microns or less) and three greenhouse gases (carbon dioxide, methane, and nitrous oxide). The model also calculates the total fuel-cycle energy consumption, fossil fuel consumption, and petroleum consumption using various transportation fuels. The GREET model includes 17 fuel cycles: petroleum to conventional gasoline, reformulated gasoline, clean diesel, liquefied petroleum gas, and electricity via residual oil; natural gas to ...
1996-03-01
This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.
2007-08-01
International Nuclear Information System (INIS)
This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.
2007-08-01
Energy Technology Data Exchange (ETDEWEB)
The go ahead for setting up the Smart Grid has been given - on the consumer side, for example, in the form of intelligent electricity meters (Smart Meter). It will be some years, however, before a comprehensive and integrated generation, transport and consumer concept can be implemented. An integral part of this implementation concept will be intelligent energy systems that coordinate individual local power grids and thus ensure optimum exploitation of the power generated. But even without full grid networking energy management can be shaped more intelligently - for example by combining and optimising the power generation capacities of several power plant locations and energy carriers. (orig.)
2010-07-01
The kWh model finds the kWh outputs of each plant and reservoir capacities of hydro and pumped storage plants and minimizes the sum of fixed charges for constructing the reservoirs and generating facilities, also the fuel costs of thermal and nuclear plants. It is a linear programming problem whose constants are represented by nonlinear functions of kW running capacity of each plant. The optimal pattern of nuclear and thermal units is found by solving the linear programming problem derived for the pumped storage and hydroplants. Excluding the upper bound constraints, the number of constraint equations are few and do not increase with the number of units, although the number of variables increases. The computing time increases only in proportion to the number of groupings of generating units. Sensitivity analysis can be done easily. The detailed operational behavior of each generating unit can be taken into account.
1979-03-01
Economic analysis of nuclear power generation
Energy Technology Data Exchange (ETDEWEB)
The major contents in this study are as follows : - long-term forecast to the year of 2040 is provided for nuclear electricity generating capacity by means of logistic curve fitting method. - the role of nuclear power in a national economy is analyzed in terms of environmental regulation. To do so, energy-economy linked model is developed. By using this model, the benefits from the introduction of nuclear power in Korea are estimated. Study on inter-industry economic activity for nuclear industry is carried out by means of an input-output analysis. Nuclear industry is examined in terms of inducement effect of production, of value-added, and of import. - economic analysis of nuclear power generation is performed especially taking into consideration wide variations of foreign currency exchange rate. The result is expressed in levelized generating costs. (author). 27 refs., 24 tabs., 44 figs
1997-12-01
Hydrogen and natural gas buses in the USA. The cleanest machines ever built
Energy Technology Data Exchange (ETDEWEB)
In 1983, the first modern urban transit bus powered by an alternative transportation fuel took to the roads in the USA. A little more than a decade later, about 2.5% of all USA buses are powered by alternative transportation fuels and about 20% of the new bus orders for delivery by 1998 will be powered by alternative fuels, mostly by natural gas. There are over 2,200 natural gas buses in operation or on order, plus about 600 additional buses powered by other alternative fuels. When these orders are completed, alternative fuel buses will constitute over 4.4% of the urban bus fleet in the USA. The widespread use of natural gas buses in the USA provides an important transition pathway for hydrogen vehicles because of the similarities between distribution, refueling and onboard energy storage technologies for the two fuels. Projects demonstrating advanced hybrid-electric buses powered by natural ...
1998-07-01
Externally fired combined cycle demonstration
Energy Technology Data Exchange (ETDEWEB)
Externally Fired Combined Cycles (EFCCs) can increase the amount of electricity produced from ash bearing fuels up to 40%, with overall powerplant efficiencies in excess of 45%. Achieving such high efficiencies requires high temperature-high pressure air heaters capable of driving modern gas turbines from gas streams containing the products of coal combustion. A pilot plant has been constructed in Kennebunk, Maine to provide proof of concept and evaluation of system components. Tests using pulverized Western Pennsylvania bituminous coal have been carried out since April, 1995. The ceramic air heater extracts energy from the products of coal combustion to power a gas turbine. This air heater has operated at gas inlet temperatures over 1,095 C and pressures over 7.0 atm without damage to the ceramic tube string components. Stable gas turbine operation has been ...
1995-11-01
Recent development in Mitsui B and W type gas injection diesel engine
Energy Technology Data Exchange (ETDEWEB)
A gas injection diesel engine was developed as an approaching measure to the diversification of fuel. Contrary to the usual low pressure gas application engine, this engine applies a so-called diffuse combustion method, in which high pressure (24.7Mpa) gas fuel is injected directly in the cylinder and is ignited and combusted by a little pilot fuel injected almost at the same time. The engine have following features. As a principle, it can attain the same heat efficiency and output rate as a diesel engine in any load range. It is excellent in responsibility to load fluctuation. There is no internal leakage of gas fuel to the scavenging chamber (the crank chamber) in the compression stroke. Not only a wide range of mixed combustion of gas fuel and heavy oil fuel, but also single combustion of heavy oil is possible. It is, therefore, drawing attention as an engine for an LNG ship and ...
1988-12-01
CFD Approaches for Modelling Bubble Entrainment by an Impinging Jet
International Nuclear Information System (INIS)
This contribution presents different approaches for the modeling of gas entrainment under water by a plunging jet. Since the generation of bubbles happens on a scale which is smaller than the bubbles, this process cannot be resolved in meso-scale simulations, which include the full length of the jet and its environment. This is why the gas entrainment has to be modeled in meso-scale simulations. In the frame of a Euler-Euler simulation, the local morphology of the phases has to be considered in the drag model. For example, the gas is a continuous phase above the water level but bubbly below the water level. Various drag models are tested and their influence on the gas void fraction below the water level is discussed. The algebraic interface area density (AIAD) model applies a drag coefficient for bubbles and a different drag coefficient for the free surface. If the AIAD model is ...
5101-01-01
Outlook for using wind energy for electrification of agriculture in Estonian SSR
Energy Technology Data Exchange (ETDEWEB)
The developed electrical networks in the agricultural regions of the Estonian SSR make it possible to construct relatively powerful wind power plants at the sites of the most favorable wind conditions with small outlays for the power transmission lines. The wind power plant electricity can be used to electrify the production processes in agriculture, while the surplus can be supplied to the energy system. The inclusion of the wind power plants in the energy system makes it possible to improve the total generation of energy or reduce the consumption of fuel. With the efficient arrangement of the wind power plants, one can also reduce the energy losses during its transfer. Calculations indicated that in the coastal zones of the Estonian SSR, one can obtain specific power of 420-480 kW/km/sup 2/. For comparison it is indicated that the Estonian SSR in the agricultural regions now uses 8-12 kW/km/sup 2/. The wind-energy ...
1982-01-01
Energy Technology Data Exchange (ETDEWEB)
The UK government's economy-wide 60% carbon dioxide reduction target by 2050 requires a paradigm shift in the whole energy system. Numerous analytical studies have concluded that the power sector is a critical contributor to a low carbon energy system, and electricity generation has dominated the policy discussion on UK decarbonisation scenarios. However, range of technical, social and market challenges, combined with alternate market investment strategies mean that large scale deployment of key classes of low carbon electricity technologies is fraught with uncertainty. The UK MARKAL energy systems model has been used to investigate these long-term uncertainties in key electricity generation options. A range of power sector specific parametric sensitivities have been performed under a 'what-if' framework to provide a systematic exploration of least-cost ...
2009-10-15
International Nuclear Information System (INIS)
The UK government's economy-wide 60% carbon dioxide reduction target by 2050 requires a paradigm shift in the whole energy system. Numerous analytical studies have concluded that the power sector is a critical contributor to a low carbon energy system, and electricity generation has dominated the policy discussion on UK decarbonisation scenarios. However, range of technical, social and market challenges, combined with alternate market investment strategies mean that large scale deployment of key classes of low carbon electricity technologies is fraught with uncertainty. The UK MARKAL energy systems model has been used to investigate these long-term uncertainties in key electricity generation options. A range of power sector specific parametric sensitivities have been performed under a 'what-if' framework to provide a systematic exploration of least-cost energy system configurations ...
2009-10-01
Energy Technology Data Exchange (ETDEWEB)
A characteristic trait of Francis turbines operating at low-head is pressure pulsations that occur during certain load levels of the generator. These stem from pressure variations across the turbine due to pulsating flow in the draft-tube. This surging action of the water column is related to draft-tube geometry and flow-rate of water in the penstock. The pressure pulsations cause torque variations on the turbine and corresponding electric power pulsations. If electric power is used as a feedback signal to the Power System Stabilizer (PSS), then Mvar and terminal voltage pulsations will occur when the generator is operating in the ``rough zone``. This paper describes field test results for investigating feedforward control from the penstock, draft tube and spiral case pressure to reduce the effects of Mw pulsations on PSS output signals. This investigation involved a PSS with ...
1993-12-01
Monthly energy review, May 1995
Energy Technology Data Exchange (ETDEWEB)
Energy production during Feb 95 totaled 5.4 quadrillion Btu (Q), 3.1% over Feb 94. Energy consumption totaled 7.4 Q, 0.7% below Feb 94. Net imports of energy totaled 1.3 Q, 5.6% below Feb 94. This publication is divided into energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy.
1995-05-24
Environmental Research Database
ObjectivesNot EnteredDescriptionMethane hydrate in an ice-like substance consisting of molecules of methane gas combined chemically with water. It is stable at high pressures and low temperatures. Since the ocean floor is normally cold, but temperatures increase with depth inside the Earth, such conditions normally prevail for a few hundred meters below the seafloor where the ocean depth is more than a few hundred metres. Methane beneath the ocean floor is formed by the decomposition of organic material. At the edges of the co [continued...
2006-01-30
Design criterion for tubed solar-heated cavity receivers
Energy Technology Data Exchange (ETDEWEB)
Solar energy can be economically converted into electrical energy for small and medium power outputs. A typical solar power plant consists of a parabolic dish, cavity receiver and gas turbine. To obtain high gas turbine efficiences, the working fluid used has to be heated to high temperatures. This necessitates the use of expensive high-quality materials for the tubes in the receiver. This expense must be kept to a minimum. The present paper demonstrates how this aim can be achieved by meeting the so-called Bammert Criterion.
1986-07-01
Design criterion for tubed solar-heated cavity receivers
Energy Technology Data Exchange (ETDEWEB)
Solar energy can be economically converted into electrical energy for small and medium power outputs. A typical solar power plant consists of a parabolic dish, cavity receiver and gas turbine. To obtain high gas turbine efficiencies, the working fluid used has to be heated to high temperatures. This necessitates the use of expensive high-quality materials for the tubes in the receiver. This expense must be kept to a minimum. The present paper demonstrates how this aim can be achieved by meeting the so-called Bammert Criterion.
1986-01-01
A Insulating Design of SF{sub 6} GAS Sealing end of Condenser Cone Type Used for 345 kV OF Cable
Energy Technology Data Exchange (ETDEWEB)
In this paper, we describes the research in condenser cone of SF{sub 6} gas sealing end for 345 kV oil-filled cable. The designed of condenser cone based on the results electric field analysis by electrostatics theory and FEM. As a results, we have been designed the condenser cone and the inner insulation part of SF{sub 6} sealing end, the width and length, the number of condenser, the length of stress relief slope, the total length of condenser cone. (author). 4 refs., 3 figs., 3 tabs.
1994-07-01
Gas and coal-fired combined cycle plants
Energy Technology Data Exchange (ETDEWEB)
Fully-fired combined cycle plants utilizing the high temperature gas turbine discharge as gas intake for a coal-fired steam generator were developed in the 1960's. Long-term experience and the excellent reliability statistics of the gas turbines of these plants have proven that the thermodynamic, economical and ecological advantages of combined cycle units over conventional units strongly suggest such plants for fossil-fuel applications. This paper describes the design and operation of these plants. Topics are Gersteinwerk Unit K combined-cycle power plant, plant design concept, design criteria and performance, gas turbines, steam generators, steam turbines, various modes of operation, typical plant start-up, environmental considerations, prototype plants and topping old steam turbine plants. It concludes that combined-cycle plants provide efficiencies ...
1986-01-01
British Library Electronic Table of Contents (United Kingdom)
We have studied the nature of continuum emitted in the visible spectral range from a noncontracted positive column of discharge in a cesium vapor-xenon mixture at a pressure of 45 Torr and at a degree of ionization below 3 ? 10?6. The main contribution to the continuous emission under such conditions is due to electron-xenon atom bremsstrahlung. The intensity of emission has been experimentally and theoretically studied as a function of the electric field strength and electron density in the positive column. It is established that an increase in the visible emission intensity with the electric field strength is related to an increase in the number of hot electrons in plasma.
2007-01-01
Direct energy recovery with ac electric power output
Energy Technology Data Exchange (ETDEWEB)
A concept of direct energy recovery system applying an alternating or rotating magnetic field is proposed for a negative-ion-based neutral beam injection system (NNB) to heat a plasma and/or drive a plasma current in a fusion reactor. Nearly same amounts of residual positive and negative hydrogen-isotope ion beams with beam energy of {approx}1 MeV are produced in an NNB using a gas neutralizing cell. Consequently, a recovered energy is obtained directly in the form of ac electric power, if these positive- and negative-ion beams are alternated or rotated and introduced to two or more recovery electrodes in turn by an alternating or rotating magnetic field. This concept will greatly reduce a technological difficulty in regeneration of a recovered electric energy with such a very high voltage. (author).
1994-12-31
Energy Technology Data Exchange (ETDEWEB)
Only about 25% of residue accumulating in the Federal Republic of Germany is currently used for the purposes of energy. This residue will be converted into fuel for power stations by the Omega process when the dumping of waste with a calorific value in excess of 5 MJ/kg is prohibited with effect from 2005. This oxygen melting process is suitable for the local use of substitute fuels. Waste is converted into a high-quality synthesis gas with a wide range of uses. The Omega process combines drying, thermal decomposition, gasification and melting of the material used in a single-stage process. This is now technologically possible for the first time by combining a metallurgical cupola furnace with a traditional gas producer. The highly-calorific synthesis gas produced by the Omega process can be used in block heat and power stations or as an industrial fuel gas, instead of natural gas. ...
2003-03-01
The SBWR (simplified boiling water reactor) thermal-hydraulic performance analysis and testing
Utility interest has recently increased in potential future nuclear units that combine the characteristics of smaller size, greater simplicity, and more passive safety features. In response to such interest, General Electric (GE) began development in 1982 of a 600-MW(electric) reactor with simplified power generation and safety systems. This paper provides an overview of the simplified boiling water reactor (SBWR) design, with emphasis on the thermal-hydraulic aspects of the design. The SBWR is a natural circulation reactor requiring no pumps to circulate the water through the core.
1989-11-01
Some implications of cancelled construction plans
Energy Technology Data Exchange (ETDEWEB)
This article addresses the possibility that electric utilities may not have enough generating capacity to meet the demands on their systems at some future date as a result of a recent spate of plant-construction cancellations, especially of nuclear facilities. It emphasizes that, when that time arrives, utilities will be willing to try every conceivable possibility for preserving the integrity of their systems, and offers differential pricing of electricity as one such possibility. The article also offers a regional analysis of the effect of plant cancellations and of the potential for differential pricing as a preventative of power shortages. 5 tables.
1982-08-19
Modeling of battery energy storage in the National Energy Modeling System
Energy Technology Data Exchange (ETDEWEB)
The National Energy Modeling System (NEMS) developed by the U.S. Department of Energy`s Energy Information Administration is a well-recognized model that is used to project the potential impact of new electric generation technologies. The NEMS model does not presently have the capability to model energy storage on the national grid. The scope of this study was to assess the feasibility of, and make recommendations for, the modeling of battery energy storage systems in the Electricity Market of the NEMS. Incorporating storage within the NEMS will allow the national benefits of storage technologies to be evaluated.
1997-12-01
High-tech hydro: an overview of pumped storage
A growing number of pumped storage plants installed within the US brings attention to the increasing significance of pumped storage as a source of electrical generation capacity. Because of the special benefits this technology has to offer, hydroelectric pumped storage is an option that many utilities should consider for the supply of new capacity requirements. This article surveys the development and use of pumped storage in the US, and considers the potential for the future development of this technology. Although some of the problems that have occurred on recent projects highlight the role of pumped storage as a technological proving ground, the article puts forth the view that pumped storage is maturing to play a significant role in US electricity supply.
Fourier Synthesization of Optical Pulses and "Polar'' Light
It is shown that the direct Fourier synthesization of light beams allows one to create polarity-asymmetric waves, which are able, in the process of nonlinear interaction with a medium, to break its inversion symmetry. As a result, these "polar" waves may show the effect of optical rectification in nonlinear centrosymmetric media by generating light-induced dc electric polarization. At the same time, the waves of this type, due to their unusual symmetry properties, can be used for detecting the direction and sign of a dc electric field applied to the medium. The prospects of application of polar waves to data recording and processing are discussed.
2002-01-01
First-generation price-squeeze policy at the FERC
Energy Technology Data Exchange (ETDEWEB)
A 1976 decision of the US Supreme Court made it clear that the Federal Energy Regulatory Commission (then the Federal Power Commission) has a responsibility to consider and determine allegations that proposed wholesale electric rates create a price squeeze against customers who compete with the wholesaler in making retail electric sales. This article reviews how the commission has approached the matter of discharging its newly recognized responsibility since that time, and describes its current position regarding the several issues and questions that price squeeze allegations raise. 35 references.
1982-09-30
Wax and hydrate control with electrical power
Energy Technology Data Exchange (ETDEWEB)
Electrical heating of subsea flowlines is an effective way to prevent wax and hydrate information, especially for long transportation distances and in low-temperature deep water. Systems are available for use in conjunction with bundles, pipe-in-pipe, and wet-thermal-insulation systems. These systems provide environmentally friendly fluid-temperature control without chemicals or flaring for pipeline depressurizing. Enhanced production is achieved because no time is lost by unnecessary depressurizing, pigging, heating-medium circulation, or removal of hydrate and wax blockages. The seabed temperature at 100-m and greater water depths may range from 7 to {minus}1.5 C, causing a rapid cooling of the hot well streams being transported in subsea flowlines. Under these supercooling conditions, vulnerable crude oils and multiphase compositions will deposit wax and asphalts; also the gas/water phase may freeze solid with hydrate particles. The paper ...
1997-08-01
Power generation from biomass residues using the gasifier/dual-fuel engine technique
Energy Technology Data Exchange (ETDEWEB)
A process is described for converting organic waste into a combustible gas for use in a heavy duty thermal engine. The engines best suited for this operation are of the dual-fuel type whose output power results from the simultaneous work of 2 combustibles. The gas flow rate is controlled by the desired power output, while diesel fuel injection remains constant regardless of engine load. The low BTU gas produced by the gasification of dry wastes is a mixture of CO, H/sub 2/ CH/sub 4/, CO/sub 2/ and N/sub 2/. Diesel fuel savings under usual operating conditions is no less than 80% of the consumption of conventional diesel engines of identical power. Characteristics of the low Btu gas engines are described as are the characteristics of the gasifying equipment. Applications for this process are suggested. (DMC)
1980-01-01
China power - thermal coal and clean coal technology export. Topical report
Energy Technology Data Exchange (ETDEWEB)
China is the world`s fourth largest electric power producer, and is expected to surpass Japan within the next two years to become the third largest power producer. During the past 15 years, China`s total electricity generation more than tripled, increasing from about 300 TWh to about 1,000 TWh. Total installed generating capacity grew at an average of 8.2 percent per year, increasing from 66 to 214 GW. The share of China`s installed capacity in Asia increased from 21 to 31 percent. The Chinese government plans to continue China`s rapid growth rate in the power sector. Total installed capacity is planned to reach 300 GW by 2000, which will generate 1,400 TWh of electricity per year. China`s long-term power sector development is subject to great uncertainty. Under the middle scenario, total capacity is expected to reach 700 GW by 2015, with annual ...
1996-12-31
Energy and nuclear power planning study for Thailand
International Nuclear Information System (INIS)
The present report describes the study conducted in co-operation with several agencies and organizations from Thailand and covers the energy and electricity requirements and the optimal expansion plans for the power generating system for this country up to year 2011. It is emphasized that the study was carried out by a team of experts from the Electricity Generating Authority of Thailand (EGAT), the National Economic and Social Development Board (NESDB), the National Energy Administration (NEA) and the Office of Atomic Energy for Peace (OAEP), who were fully responsible for all phases of the study, including the production of the present report. The IAEA's responsibility was to provide overall co-ordination and general guidance during the conduct of the study, as well as training and assistance in the implementation and use of the IAEA's computerized planning methodologies on the computer facilities of ...
2002-06-16
British Nuclear Fuels PLC: report and accounts 1988-89
International Nuclear Information System (INIS)
This item covers a meeting held between members of the United Kingdom government's energy committee and representatives of British Nuclear Fuels (BNFL) to discuss their Annual Report and Accounts for the year 1988-89. The committee explored the reasons for escalating predictions of the costs of nuclear power and why decommissioning costs are so difficult to estimate accurately so as to include them in cost per kilowatt hour of generated electricity. The relationship between BNFL and the Ministry of Defence (MoD) was explored, as was the MoD's relationship with the United States Department of Defense. BNFL's financial position should improve when the thermal oxide reprocessing plant at Sellafield becomes operational, and the Chapelcross and Calder Hall reactors may contribute income from electricity generation. (UK).
Biofuels for electricity and heating - obstacles for increased utilization
International Nuclear Information System (INIS)
The aim of this report is to describe the present situation regarding biomass utilization in small power plants, 0.5 - 20 MW fuel power. Also discussed are the most important technical, economical and environmental conditions which may prevent a fast expansion of small biomass fueled power plants for generation of district heating in smaller networks and also for electric power generation. Biofuels means a reduction of the net emission of carbon dioxide, but emission of other compounds are not very well known for this size of power plants. There are only a few biofueled power plants in Sweden and only a couple with less than 20 MW power supplied. New concepts are under development but not much have been achieved during the most recent years. 25 refs, 10 figs, 9 tabs.
Bidding strategy for pumped-storage plant in pool-based electricity market
Energy Technology Data Exchange (ETDEWEB)
This paper develops optimal bidding strategies for a pumped-storage plant in a pool-based electricity market. In the competitive regime, when compared to simple hydroelectric generator, profit of the pumped-storage plant is maximized by operating it as a generator when market clearing price is high and as a pump when the price is low. Based on forecasted hourly market clearing price, a multistage looping algorithm to maximize the profit of a pumped-storage plant is developed, considering both the spinning and non-spinning reserve bids and meeting the technical operating constraints of the plant. The proposed model is adaptive for the nonlinear three-dimensional relationship between the power produced, the energy stored, and the head of the associated reservoir. Different operating cycles for a realistic pumped-storage plant are considered and simulation results are reported and compared. (author)
2010-03-15
A novel EPROM device fabricated using focused boron ion-beam implantation
Energy Technology Data Exchange (ETDEWEB)
A novel floating-gate avalanche injection (FAMOS) type erasable programmable read-only memory (EPROM) device is demonstrated, with a heavily focused ion-beam (FIB) implanted region of about 0.2-..mu..m width at the drain edge of the channel. This heavily B/sup +/-doped region permits a higher electric field near the drain edge, resulting in a remarkable increase of the hot-carrier generation rate, and reduces both the programming voltage and programming time. A three-dimensional device simulator, CADDETH, predicted that the electric field at the drain edge would increase by about six times, which would lead to hot-carrier generation efficiency three orders of magnitude higher.
1987-06-01
International Nuclear Information System (INIS)
As a continuation of its efforts to provide methodologies and tools to Member States to carry out comparative assessment and analyse priority environmental issues related to the development of the electric power sector, the IAEA has completed a new version of the Wien Automatic System Planning (WASP) Package WASP-IV for carrying out power generation expansion planning taking into consideration fuel availability and environmental constraints. This manual constitutes a part of this work and aims to provide users with a guide to use effectively the new version of the model WASP-IV. WASP was originally developed in 1972 by the Tennessee Valley Authority and the Oak Ridge National Laboratory in the USA to meet the IAEA needs to analyse the economic competitiveness of nuclear power in comparison to other generation expansion alternatives for supplying the future electricity requirements of a country or ...
1997-12-01
Energy Technology Data Exchange (ETDEWEB)
Generation of anomalous resistivity and dynamical development of collisionless reconnection in the vicinity of a magnetically neutral sheet are investigated by means of a three-dimensional particle simulation. For no external driving source, two different types of plasma instabilities are excited in the current layer. The lower hybrid drift instability (LHDI) is observed to grow in the periphery of current layer in an early period, while a drift kink instability (DKI) is triggered at the neutral sheet in a late period as a result of the nonlinear deformation of the current sheet by the LHDI. A reconnection electric field grows at the neutral sheet in accordance with the excitation of the DKI. When an external driving field exists, the convective electric field penetrates into the current layer through the particle kinetic effect and collisionless reconnection is triggered by the convective electric ...
1999-06-01
Customer and service profitability
Energy Technology Data Exchange (ETDEWEB)
The rapid pace of competitive change in the generation sector has pushed electric utilities to rethink the concept of being obligated to serve all customers and with this change, the notion of measuring customer profitability is also being redefined. Traditionally, uniform services were provided to all customers. Rates were based on each customer classes` contribution to average costs, and consequently return was equally allocated across all customer segments. Profitability was defined strictly on an aggregate basis. The increasing demand for choice by electric customers will require electricity providers to redefine if not who they serve, than certainly how they provide differentiated services tailored to specific customer segments. Utilities are beginning to analyze the value, or profitability, of offering these services. Aggregate data no longer provides an accurate assessment of how resources should ...
1996-03-01
International Nuclear Information System (INIS)
The deliveration by the Nuclear Safety Commission was commenced on the alteration in reactor installation, as it had been inquired by the Ministry of International Trade and Industry. The alteration is the additional installation of the reactor No. 2 in the Sendai Nuclear Power Station, Kyushu Electric Power Co., Inc. It is a PWR power plant with thermal output of about 2,660 MW (electric output of 890 MW), to be installed, adjoining to the reactor No. 1 of the same type and capacity under construction. In the examination by MITI, it was confirmed that the technological capabilities for its construction and operation and the radiation protection measures in power generation are both sufficient. The contents of the examination include the siting conditions, the location and construction of reactor facilities, etc. (J.P.N.).
1980-01-01
Energy Technology Data Exchange (ETDEWEB)
The deliberation by the Nuclear Safety Commission was initiated on the alteration in reactor installation, as was required by the Ministry of International Trade and Industry. The alteration is the additional installation of the reactor No. 2 in the Sendai Nuclear Power Station, Kyushu Electric Power Co., Inc. It is a PWR power plant with thermal output of about 2,660 MW (electric output of 890 MW), to be installed, adjoining to the reactor No. 1 of the same type and capacity under construction. In the examination by MITI, it was confirmed that the technological capabilities for its construction and operation and the radiation protection measures in power generation are both sufficient. The contents of the examination include the siting conditions, the location and construction of reactor facilities, etc.
1980-10-01
A study of solar-powered, high-altitude unmanned aerial vehicles
British Library Electronic Table of Contents (United Kingdom)
Purpose ? Aims to present a methodology for analysing a solar-electric, high-altitude, long-endurance, unmanned aircraft. Design/methodology/approach ? The study focuses on the aerodynamics, flight performance and power requirements of a heavier-than-air, solar-electric, HALE UAV. The methodology is founded on using an analytical approach to determine the power required to undertake various flight manoeuvres. An analytical approach is also undertaken in determining the intensity of the solar radiation available to the aircraft. Finally to demonstrate the methodology, a HALE concept was generated and evaluated. Findings ? When using estimates of current solar-electric propulsion and energy conversion efficiencies, the HALE concept was only able to sustain year round, level flight up to lati...
2006-01-01
Energy Technology Data Exchange (ETDEWEB)
This is the eighth part of a ten-part final report for the Swiss Federal Office of Energy (SFOE) on a project that looked into potential problems relating to the Swiss electricity distribution grid with respect to the increasing number of distributed power generation facilities being put into service. The identification of special conditions for the grid's operation and future development that take increasing decentralised power production into account are discussed. The results of the project activities encompass the analysis and evaluation of various problem areas associated with planning and management of the grid during normal operation and periods of malfunction, as well as required modifications to safety systems and grid configurations. This seventh appendix to the main report summarises and discusses the knowledge gained during the project and attempts to provide answers to various questions posed by the use of distributed ...
2003-07-01
Fuel cells and electricity companies - new risk management opportunities
International Nuclear Information System (INIS)
'Full text:' Deregulation, distributed generation, combined heat and power, renewables, fuel cells, hydrogen. Power companies are facing a rapidly evolving environment that is testing their ability to effectively deploy capital and earn profits. While recent deregulation trends have shifted the structure of power markets into separating generators from distributors, the improving economic value proposition offered by smaller scale distributed generation technologies - such as fuel cells - would seem to be a conflicting development. In this complex and changing environment, decisions based on the economic reality of the capital markets are likely to prevail. By examining the opportunity to enhance risk management offered by stationary fuel cells, particularly in CHP applications, we provide a context for the issues being discussed in today's sessions focusing on power companies and electric utilities. ...
2004-09-25
Energy Technology Data Exchange (ETDEWEB)
Since 1994-95 the University of Applied Sciences Berne is working on weather-proof electric bicycles. The main drawbacks of bicycles, no weather-protection, little comfort of the saddle, the difficulty of climbing hills, are to be eliminated. The electro-mechanical drive-train of 'Ultraleichtmobil ULM BE 2000', developed in 1995-96, was mechanically complicated. This resulted in reduced energy-efficiency and intense maintenance. Too, the drive-train was expensive in production. A fully electrical human-power transmission seemed to be the solution to the problems mentioned above. It is appealing not only to the user of the vehicle, but also to the producer and to the persons doing the maintenance. Following an internal study showing the technical feasibility of such an electrical transmission, a controllable DC/DC-converter which allows to operate a pedal-driven generator at maximum ...
1999-12-01
SGTR Project: Separate Effect Studies for Vertical Steam Generators
Energy Technology Data Exchange (ETDEWEB)
The SGTR project has been carried out within the fifth EURATOM Framework Programme (Contract No FIKS-CT-1999-0007). Its main objective was to provide an experimental database and to develop and/or verify models to support definition of accident management measures in the hypothetical case of a Steam Generator tube Rupture (SGTR) sequence. The project addressed both vertical and horizontal steam generator designs. This report summarises the main results obtained in the intermediate scale experimentation that addressed Western type steam generators. The specific goal of this test programme was to investigate aerosol retention in the break stage of the secondary side of a water-empty steam generator. The test matrix consisted of 12 tests that explored the influence of variables such as break type and orientation and inlet gas flow rate. This work was performed in the PECA facility of ...
2003-07-01
Energy Technology Data Exchange (ETDEWEB)
A compact and energy independent solar-powered refrigeration unit was to be developed to store and transport small quantities of high-quality commodities needing refrigeration. This unit comprises the following matched components: thermo-electrical refrigerator unit, solar generator and transport equipment. The solar generator is a specially developed panel with 36 cells. This unit may best be used in human medicine, veterinary medicine, environmental protection analysis, laboratories and leisure time activities. (BWI)
1994-01-01
Energy Technology Data Exchange (ETDEWEB)
In order to ensure a power balance in an electrical network a spinning reserve has to be capable of activation within seconds. However, because of the need to vary the fuel flow in the steam generator, the run-up of output takes minutes. The required capacity response is therefore achieved by storage of steam from the steam generator. In this process the turbine control valves come into action in a specific manner. The paper describes the importance of the initial reserve for unit capacity control. (orig.).
1989-09-01
On the threshold of the 21st Century in the Soviet Union
International Nuclear Information System (INIS)
In the last 30 years the production of electricity in the USSR has increased 14-fold, probably attaining 1540 billion kWH in 1985. Nuclear generation will provide the bulk of future increases of consumption, using both water-cooled and uranium/graphite reactors; stations of up to 1.5 million kW are in service. The USSR is also in the fore-front of attempts to exploit thermonuclear power. The USSR is also conducting experiments with renewable sources of energy such as solar, geothermal, wind and wave power and with magnetohydrodynamic generation. (D.A.J.).
Conception and design of steam power plants
International Nuclear Information System (INIS)
The manual presents the fundamentals of thermodynamics and fluid mechanics, the main components of steam power plants, and the power generation process. The following concepts and subjects are discussed at length: steam generator; steam turbines; turbogenerators; condensers; cooling technology; water/steam cycle and water treatment; design data of fossil-fuelled power plants; design and optimisation of nuclear power plant thermodynamics; pipelines and fittings; control systems in steam power plants; connection to the electricity grid and self-supply of thermal power plants; power plant transformer concepts and definitions. (HAG).
Energy Technology Data Exchange (ETDEWEB)
The petroleum and petroleum products increase offer a real development opportunity to the alternative fuels. In the context of the french energy accounting increase, the energy independence notion incites the government to promote these new fuels. If the LPG seems declining because of the accident risks fear, the fuel cell is not for today. Near these two sectors what is the future of the biofuels and the natural gas vehicle or the electric cars? (A.L.B.)
2006-06-15
The development perspectives of the alternative fuels
International Nuclear Information System (INIS)
The petroleum and petroleum products increase offer a real development opportunity to the alternative fuels. In the context of the french energy accounting increase, the energy independence notion incites the government to promote these new fuels. If the LPG seems declining because of the accident risks fear, the fuel cell is not for today. Near these two sectors what is the future of the biofuels and the natural gas vehicle or the electric cars? (A.L.B.)
The Philadelphia Marriott: A convention center flagship hotel
Energy Technology Data Exchange (ETDEWEB)
This article describes the state-of-the-art HVAC system at the Philadelphia Marriott Hotel. Thermal comfort and indoor air quality are emphasized. The system uses a hybrid gas absorption/electric centrifugal chilled water plant, variable flow pumping, water-side economizers to provide free cooling, central air handling units with air-side economizers and flow monitoring equipment.
1997-01-01
Tap cogen-plant steam for process, NO[sub x] control
Energy Technology Data Exchange (ETDEWEB)
This article describes the Monsanto's Indian Orchard plant gas-fired, combined-cycle cogeneration facility in Springfield, Massachusetts. The topics of the article include project configuration, the thermodynamic cycle, fuel selection, electrical distribution system, plant control, and air pollution control of NO[sub X], SO[sub 2], CO, particulates, non-methane hydrocarbons, opacity and ammonia.
1993-04-01
Solar energy conversions: solar-electric thermophotovoltaic systems and solar-powered gas lasers
Energy Technology Data Exchange (ETDEWEB)
This paper deals with conversions of solar energy efficiently into electricity and into gas laser radiation. In the first section, a review study of the possibility of a solar-electric thermophotovoltaic (TPV) device has been done. In a proposed extension of the TPV concept, a Cassagranian optical system concentrates solar radiation to heat a blackbody cavity to 2400/sup 0/K. A double-layer solar cell, GaAs and Si, forming the cylindrical surface concentric to the blackbody cavity, receives the blackbody radiation and converts it into electricity efficiently. A cell conversion efficiency of 50% or more would be possible with the TPV system. The second section explores the concept of blackbody radiation pumping of gas laser media as a step toward utilization of solar energy as a laser pumping source. To demonstrate this concept, an experiment was performed in which various ...
1980-12-01
Quantum theory of light interstitial diffusion and other aspects of inert gas motion in solids
International Nuclear Information System (INIS)
Most diffusion phenomena in solids can be understood (or sometimes misunderstood) on a purely classical model. For light interstitials (hydrogen isotopes, the positive muon, and potentially He) there may be anomalous temperature dependences, and isotope effects, and anomalous response to electric fields and temperature gradients. Some of these anomalies are quantal in origin, and will be discussed. (author).
1980-03-01
Monthly energy review, October 1998
Energy Technology Data Exchange (ETDEWEB)
The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.
1998-10-01
Energy Technology Data Exchange (ETDEWEB)
This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.
1996-05-28
Energy Technology Data Exchange (ETDEWEB)
Contains Executive Summary and Chapters on: Energy and the Internet; Internet Developments; Search Guide; Oil and Gas Industry; Electricity and Utilities; Nuclear Energy; Coal Industry; Alternative Energy; Government and Supranational Agencies; Research Institutions and Universities; Energy Statistics; Commodity Pricing and financial Markets; Company Information; Country Information; Associations; Engineering; Environment; Patents, Trademarks and Standards; News; Industry Events; Miscellaneous. (Author)
1999-10-01
Emission control cost-effectiveness of alternative-fuel vehicles
Energy Technology Data Exchange (ETDEWEB)
Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquefied petroleum gas, compressed natural gas, and electricity. Vehicle emission estimates included both exhaust and evaporative emissions for air pollutants of hydrocarbon, carbon monoxide, nitrogen oxides, and air-toxic pollutants of benzene, formaldehyde, 1,3-butadiene, and acetaldehyde. Vehicle life-cycle cost estimates accounted for vehicle purchase prices, vehicle life, fuel costs, and vehicle maintenance costs. Emission control cost-effectiveness presented in dollars per ton of emission reduction was calculated ...
1993-06-14
The report describes the site specific changes required to convert an existing lime FGD system to a limestone system enhanced by dibasic acid (DBA) or adipic acid, and the costs of making such a change. In 1982-83, pilot plant tests were conducted at the R. D. Green Station of Bi...
British Retail Consortium - BRC Services
... IN-STORE PROCUREMENT SERVICES - Energy (Electric/Gas) - Telecoms (Call/Lines/Switchboards/Mobiles) - Waste & waste compliance (Cleaning/Collection/Compliance) - Carrier bags (Plastic/Paper) - Stationery (Supplies) - Catering (Consumables/Equipment) - Insurance (Business/Legal/Personal) - Water (Rates/Coolers) - Personnel (Staff Uniforms/Recruitment/Training) - Security (Patrols/Surveillance Equipment) - Instore ...
Pumped-storage: peak generation or operating reserve
Energy Technology Data Exchange (ETDEWEB)
The trade-off which must be established between the various functions of pumped-storage plants is examined. A compromise between supply security and economic planning can be found only by coordinated planning of pumped-storage units and thermal generation plants. A model used by Electricite de France (EDF) to ensure optimized daily planning of thermal and pumped-storage units is described. The model, called the DEMETER model, ensures the optimization of the daily planning of thermal and pumped-storage plants. The model iterates between two levels: coordination where the prices of the generated energy and the operating reserve are determined to adjust generation to load and keep a sufficient reserve; and decomposition where the schedule of each unit is optimized on the basis of the above prices and taking into account local constraints such as unavailability, and minimum shut down time. The role of EDF is to supply customers ...
1984-08-01
An evaluation of the performance of integrated bioenergy systems
Energy Technology Data Exchange (ETDEWEB)
A comprehensive study of biomass production conversion and utilisation systems has been carried out to examine complete bio-energy systems from biomass in the forest to electricity delivered to the grid. Models have been derived for all of the key steps in an integrated process which have been compiled into an overall system model. Biomass production from short rotation forestry and from conventional forestry is modelled on an individual operation basis in terms of the performance and cost of each step. This includes planting, maintenance, harvesting, chipping, storage and transport. Biomass conversion includes pretreatment (reception, storage, handling, comminution, screening and drying); atmospheric gasification (generic gasifier, water scrubbing, gas engine); pressure gasification (generic gasifier, hot gas clean-up, gas turbine, HRSG, steam turbine); fast pyrolysis for liquid bio-fuel-oil ...
1995-11-01
Energy Technology Data Exchange (ETDEWEB)
Precondition for the low-NO operation of gas turbine burners is the generation of as homogeneous as possible a gaseous fuel/air mixture. Such a burner behavior can be achieved by selective adaptation of the flow and injection. A computing model is introduced that calculates the dynamically balanced GASs/droplet flow through numerical solution of the transport equations in a curved orthogonal coordinate system. The feedback reaction of the fuel droplets to the gas phase is considered by source terms and/or sink terms. Test computations were carried out for comparison with analytical solutions from the flow mechanics and validated by comparison with measurement results. Droplet motion and evaporation were checked by means of published experimental results on single droplets. For the validation of the developed computing technique, model tests were carried out with water in place of fuel. It is pointed out that the choice of ...
1989-01-01
G3 model of gas and liquid migration from grout containing radioactive waste
Energy Technology Data Exchange (ETDEWEB)
Grout has been evaluated as a means of containing low-level radioactive waste for long-term disposal. Concerns about hydrogen and reactive gas generation in the Hanford Site grout disposal facility lead to the development of the G3 model, which has predicted buildup of radiolytically formed gases in the grout region and their migration to air-filled regions. The G3 model is a one-dimensional code that couples models of gas diffusion with two-phase gas and liquid flow. It was coupled to a compartment diffusion model and these models predicted the concentrations of hydrogen I nitrous oxide, and other gases in air-filled regions of the grout disposal facility. The results have served as the technical basis for safety studies. A unique finding of the G3 model was that a liquid return, or expulsion of unbound liquid from the grout region, could occur. This liquid return is driven by displacement caused by ...
1994-11-01
Energy Technology Data Exchange (ETDEWEB)
Operation safety and reliability are major guidelines in the design of city-gate units. Conventional natural gas heaters operate by a indirect mechanism, where liquid water is used to transfer heat by natural convection between the combustion chamber and the natural gas coil. In this work, the concept of vapor chamber is evaluated as an indirect gas heater. In a vapor chamber, liquid water is in contact with the heat source, and vaporizes. The vapor condenses in contact with the heat sink. A reduced scale model was built and tested in order to compare these two heating concepts where the combustion chamber was replaced by electrical cartridge heaters. This engineering model can operate either as a conventional heater or as a vapor chamber. The comparison between the concepts was done by inducing a controlled power to the cartridges and by measuring the resulting temperature distributions. In the novel ...
2005-07-01
Study on core cooling of hybrid safety system for next-generation PWR during LOCA
International Nuclear Information System (INIS)
Mitsubishi is now developing a next-generation Pressurized Water Reactor (PWR) which has the innovative feature of hybrid safety systems (optimum combination of passive safety system and active safety system) and passive core cooling by horizontal steam generators during Loss of Coolant Accident (LOCA). In order to confirm the capability of this passive core cooling system during LOCAs, the thermal-hydraulic tests of horizontal steam generator and the integral thermal-hydraulic tests simulating the LOCAs were performed. The thermal-hydraulic tests of horizontal steam generator consist of a single tube test and a multi-tubes test. On the basis of these test results, the heat transfer characteristics of steam-water two-phase flow with noncondensable gas along a long horizontal tube is understood and the heat transfer correlation including the effect of noncondensable ...
1995-04-23
Energy Technology Data Exchange (ETDEWEB)
A century ago--in the year J.J. Thomson discovered the electron--electricity, gas and traction companies battled for markets, and corrupt city councils demanded their fair share of the take. One tycoon became so disgusted with the confusion and dishonesty that he decided to bribe the legislature to set up an honest, state-run regulatory agency that would bring order to chaos. But he was found out. The scandal set back the cause of regulation until 1907, the year in which the electric washing machine and the vacuum cleaner were invented. By then, electricity sales had septupled from 1897 levels, and three states had established utility regulation. In the coming decade, 1997 to 2007, the utility business could undergo similar dramatic change, but it will move toward less regulation and more competition during a period of slow growth. Management will have to work harder to achieve success, however, because ...
1998-10-01
Primary coolant depressurization facility
Energy Technology Data Exchange (ETDEWEB)
In a PWR type reactor, a primary coolant circuit system using a steam generator is adopted in order to accelerate depressurization of a primary coolant circuit upon small rupture LOCA in which the pressure of the primary coolant circuit is moderately depressurized. A secondary coolant circuit depressurization valve is disposed to a main steam pipeline. The valve has a performance of automatically opening to remove heat by evaporation of water stored in SG for a short period of time when the pressure in the primary circuit is decreased to about 50kg/cm[sup 2] upon occurrence of LOCA or the like. Then, the secondary side of the SG is depressurized to about atmospheric pressure and gravitational water injection from a condensate tank is started. Further, a gas vent valve is disposed to a water chamber of the steam generator. The valve has a performance of automatically opening to discharge incondensible ...
1992-10-14
International Nuclear Information System (INIS)
We report coupling and guiding of pulses of peak power up to 0.3 TW in 1.5 cm long preformed plasma waveguides generated in a high repetition rate argon gas jet. Coupling of up to 52% was measured for 50 mJ, -110 fs pulses injected at times longer than 20 ns, giving guided intensities up to -5x1016 W/cm2. It was found that for short delays between waveguide generation and pulse injection, pulse shortening occurred, with this effect reduced as delay was increased. Injection into the waveguide of two consecutive pulses separated by a few nanoseconds resulted in the reduction of shortening of the second pulse at all delays. Femtosecond time-resolved shadowgrams of the coupling of injected pulses into the waveguide show that there is ?0.5 mm of neutral gas remaining at the waveguide entrance after waveguide generation.
1999-07-12
Design/build/mockup of the Waste Isolation Pilot Plant gas generation experiment glovebox
Energy Technology Data Exchange (ETDEWEB)
A glovebox was designed, fabricated, and mocked-up for the WIPP Gas Generation Experiments (GGE) being conducted at ANL-W. GGE will determine the gas generation rates from materials in contact handled transuranic waste at likely long term repository temperature and pressure conditions. Since the customer`s schedule did not permit time for performing R&D of the support systems, designing the glovebox, and fabricating the glovebox in a serial fashion, a parallel approach was undertaken. As R&D of the sampling system and other support systems was initiated, a specification was written concurrently for contracting a manufacturer to design and build the glovebox and support equipment. The contractor understood that the R&D being performed at ANL-W would add additional functional requirements to the glovebox design. Initially, the contractor had sufficient information to design the glovebox shell. ...
1996-10-01
International Nuclear Information System (INIS)
In this work we investigate an iron oxide thin film grown with atomic layer deposition for a gas sensor application. The objective is to characterize the structural, chemical, and electrical properties of the film, and to demonstrate its gas-sensitivity. The obtained scanning electron microscopy and atomic force microscopy results indicate that the film has a granular structure and that it has grown mainly on the glass substrate leaving the platinum electrodes uncovered. X-ray diffraction results show that iron oxide is in the #alpha#-Fe_2O_3 (hematite) phase. X-ray photoelectron spectra recorded at elevated temperature imply that the surface iron is mainly in the Fe"3"+ state and that oxygen has two chemical states: one corresponding to the lattice oxygen and the other to adsorbed oxygen species. Electric conductivity has an activation energy of 0.3-0.5 eV and almost Ohmic current-voltage dependency. ...
2008-07-31
International Nuclear Information System (INIS)
A new miniature high-frequency (HF) plasma source intended for bio-medical applications is studied using nitrogen/oxygen mixture at atmospheric pressure. This plasma source can be used as an element of a plasma source array for applications in dermatology and surgery. Nitric oxide and ozone which are produced in this plasma source are well-known agents for proliferation of the cells, inhalation therapy for newborn infants, disinfection of wounds and blood ozonation. Using optical emission spectroscopy, microphotography and numerical simulation, the gas temperature in the active plasma region and plasma parameters (electron density and electron distribution function) are determined for varied nitrogen/oxygen flows. The influence of the gas flows on the plasma conditions is studied. Ozone and nitric oxide concentrations in the effluent of the plasma source are measured using absorption spectroscopy and electro-chemical NO-detector at variable ...
2010-01-01
Hydraulic system for driving control rods
International Nuclear Information System (INIS)
Purpose: To enable safety reactor shut down upon occurrence of an abnormal excess pressure in a hydraulic control unit. Constitution: The actuation pressure for a pressure switch that generates a scram signal is set lower than the release pressure set to a pressure release valve. Thus, if the pressure of nitrogen gas in a nitrogen container increases such as upon exposure of the hydraulic control unit to a high temperature, the pressure switch is actuated at first to generate the scram signal and a scram valve is opened to supply water at high pressure to control rod drives under the driving force of the nitrogen gas at high pressure to rapidly insert the control element into the reactor and shut down it. If the pressure of the nitrogen gas still increases after the scram, the pressure release valve is opened to release the nitrogen gas at high temperature to ...
1980-11-07
Deformed-coal structure and control to coal-gas outburst
Energy Technology Data Exchange (ETDEWEB)
Based on techniques of organic solvent extraction and a thermal model experiments of coal-related hydrocarbon, the variation of coal structure and the character of deformed coal-related hydrocarbons were studied when the coal seam at Piagdingshan mine, China was modified by tectonic stress. The results show that the extraction ratio by n-hexane and benzene from the deformed coal approaches that form normal coal, but the extraction ratio by chloroform from the deformed coal is two times more than that from normal coal. The deformed coal has higher solvable low-molecular weight compounds than normal coal. The intermolecular force of deformed coal is relatively small. The deformed coal has low strength and high adsorption capacity, and these determine the outbreak of coal-gas outburst. The extraction yields by chloroform can be taken as an index of forecast risks of coal-gas outburst. The potentially of generating hydrocarbon ...
2007-03-15
Rents in the European power sector due to carbon trading
International Nuclear Information System (INIS)
The European Union Emissions Trading Scheme (EU ETS) has imposed a price on the allowances for CO2 emissions of electricity companies. Integrating this allowance price into the price of electricity earns a rent for companies who have received these allowances for free. During Phase I, 2005-2007, rents corresponding to the aggregate value of allocated allowances amounted to roughly Euro 13 billion per year. However, due to the specific price-setting mechanism in electricity markets true rents were considerably higher. This is due to the fact that companies also that have not received any allowances gain additional infra-marginal rents to the extent that their variable costs are below the new market price after inclusion of the allowance price. Producers with low carbon emissions and low marginal costs thus also benefit substantially from carbon pricing. This paper develops a methodology to determine the specific interaction ...
2010-08-01
Energy Technology Data Exchange (ETDEWEB)
What utilizes the effect of electrohydrodynamical technique (EHD), as one of heat transfer augmentation methods, is methodically frequented and partially prepared to be put to practical use. Then, the heat transfer augmentation effect on nucleate boiling, utilizing the EHD effect, was both experimentally and theoretically studied from both the applicative and basic viewpoints. By adding fleon with 2wt% ethyl alcohol, higher in electric conductivity, in order to have the mitigation time of electric charge correspond to the bubbling frequency of bubble, the heat transfer augmentation was enabled to be about 8.5 times as high as that without impressing the electric field. As a result of observing the behavior of bubble in the electric field, was observed a phenomenon of bubble, moving from place to place, without ascending, on the plane electrode plate, by which could be found one of causes of the heat ...
1990-07-25
Stretch-out operation and extended low power operation in Daya Bay Nuclear Power Station
International Nuclear Information System (INIS)
Stretch-Out and Extended Low Power Operation is two particular operating modes applied for nuclear electricity generation. The relevant safety analysis and the impacts on plant operation are well illustrated, as well as some operation experiences earned in Daya Bay nuclear power station. The safety analysis and plant practice show that Stretch-Out operation and Extended Low Power Operation are operable in Daya Bay nuclear power station
2002-10-01
Energy Technology Data Exchange (ETDEWEB)
This paper describes the implementations of a fuzzy logic based self-tuned controller to improve the stability of electric power systems. The stabilizing signal is computed using the standard fuzzy membership function depending on the speed/acceleration state of the generator in the phase plane. The performance of the proposed stabilizer is demonstrated by practical implementation using a digital signal processor mounted on a PC-AT. Results of the experimental tests on a physical model of a power system are presented.
1993-06-01
Flexible DER Utility Interface System: Final Report, September 2004--May 2006
Energy Technology Data Exchange (ETDEWEB)
In an effort to accelerate deployment of Distributed Energy Resources (DER) such as wind, solar, and conventional backup generators to our nation's electrical grid, Northern Power Systems (NPS), the California Energy Commission (CEC), and the National Renewable Energy Laboratory (NREL) collaborated to create a prototype universal interconnect device called the DER Switch.
2006-08-01
Externally fired combined cycle for electric power generation from coal
Energy Technology Data Exchange (ETDEWEB)
The externally fired combined cycle is emerging as an economically viable repowering options for old non-competitive coal fired steam plants. This paper describes the initial operation of a pilot plant located at Kennebunk, Maine and the initial work on the repowering of a 48MW coal fired steam plant located in Warren, PA.
1994-12-31
Dual fuel engine solves the solvent problem
Energy Technology Data Exchange (ETDEWEB)
Some 200 visitors attended the official opening of a new diesel engine driven cogeneration plant in the city of Hamburg at the end of March. The dual fuel engine built by Blohm+Voss will supply 7.7 MW of electricity to the grid and 8.26 MW of thermal power to generate steam and hot water. (author)
1993-05-01
Energy Technology Data Exchange (ETDEWEB)
The operating histories and performance of a large (180 MWsub(e)) central condensing plant and five small (5 MWsub(e)) wellhead backpressure power plants are presented. The thermodynamic performance of the central plant is compared with an estimated possible performance based upon the work of Michaelides. Both types of plant have been shown to be reliable despite some problems due to the contaminants which are associated with geothermal steam.
1986-01-01
Development of Hardware for Power System Stabilizer (PSS)
Energy Technology Data Exchange (ETDEWEB)
The basic function of a Power System Stabilizer (PSS) is to add damping to the generator rotor oscillations by controlling its excitation using auxiliary stabilizing signals. To provide damping, the stabilizer must produce a component of electrical torque in phase with the rotor speed deviations. This paper introduces the hardware specifications and various functions of microprocessor (TMS320C32)-based digital PSS to provide the damping torque. (author). 3 refs., 6 figs.
2001-07-01
Coal uses and upgrading processes
Energy Technology Data Exchange (ETDEWEB)
The paper discusses the status of coal as a raw material and energy source. After referring to coal preparation and the costs it involves the author deals with coal/liquid suspensions and their fueling uses. Access is given to different aspects concerning the use of coal for electric power and heat generation. They include pollution abatement measures, economic analyses and fuel engineering in the case of coal. Further sections are dedicated to upgrading procedures such as the gasification, liquefaction and coking of coal. A bibliography informs the reader about further publications available on the subject. (HAG).
1986-04-01
Bio gasification of industrial bio waste and sewage sludge-management of biogas quality
International Nuclear Information System (INIS)
Bio gasification, i. e. anaerobic digestion, is a well known sustainable option for the management of organic solid wastes and sludges. the produced biogas is a valuable bio fuel to replace fossil fuels in different technical applications (like heating, electricity, transport fuel generation) which in turn determine its quality requirements. (Author)
Energy Technology Data Exchange (ETDEWEB)
(1) Most ancillary services needed for real-time control of the transmission grid and to meet operating criteria can be competitively supplied and competitively procured. (2) The independent service operator (ISO) must directly control the generators and loads, which supply ancillary services. (3) Comparability of access to ancillary services is achievable through the ISO-based competitive market structure.
1996-03-01
Advanced hydrogen fueled internal combustion engines
Energy Technology Data Exchange (ETDEWEB)
The Hydrogen Program at Sandia National Laboratories is developing internal combustion engine generators for application in series hybrid vehicles and stationary power units. The program consists of two approaches: investigating the utilization of hydrogen in a conventional crankshaft driven engine and in an advanced free piston configuration. The conventional engine program has taken the direction of utilizing the unique ability to spark ignite homogeneous fuel/air mixtures of hydrogen at low equivalence ratios to achieve low NO{sub x} emissions and high thermal efficiency. The goal is to translate the indicated thermal efficiency of single-cylinder engines into multicylinder configurations achieving at least 40% brake thermal efficiency. When coupled to an electrical generator, the fuel to electricity conversion efficiency would be approximately 37%. A modified Perkins 3.152 Diesel engine is currently ...
1998-01-01
International Nuclear Information System (INIS)
This paper reviews the state of the art of silicon-germanium technology and assesses the problems of building thermoelectric modules in Europe, based upon silicon-germanium alloys, for use in multihundred watt radio-isotope thermoelectric generator. The generator developed in the United States for the International Solar Polar mission has been used as a reference system. The essential features of an alternative system, which employs thermocouples fabricated from improved silicon-germanium alloys based upon a design by the Fairchild Space and Electronics Company, is also described. It is concluded that although the fabrication of reliable electrical contacts will present a major problem, the technology is available in Europe to build thermoelectric modules similar to those developed for the International Solar Polar mission. (orig.).
British Library Electronic Table of Contents (United Kingdom)
In this paper, the performance of customer-owned distributed generation (DG) units is quantified from different perspectives through an uncertainty study. A Monte Carlo-based method is applied to assess the stochastic operation of the customer-owned DG units in the power distribution system. Several cases are studied to analyze the impact on system performance of using such generators, with the emphasis on benefits. The results of the studied cases show that proper operation of customer-owned DG units placed close to significant consumption centers offers several benefits which lead to significant energy savings and improvement in the performance indices while maintaining the cost-effectiveness. Furthermore, based on the energy demand, different electricity price scenarios considering a co...
2011-01-01
An efficient algorithm for the design of decentralized output feedback power system stabilizer
A new algorithm for the design of decentralized output feedback stabilizers for large-scale electric power systems is presented in this paper. In the proposed approach, the generators which are most effective for stabilizer applications are first identified by using participation factors. Then an efficient algorithm based on decentralized pole assignment is proposed for the determination of the parameters of the power system stabilizers which, due to the difficulty associated with the communication among the geographically dispersed generating stations in a large power system, are essentially decentralized compensators using local generator outputs as their feedback signals. The proposed method is computationally efficient and can be applied to any large-scale system. The simplicity and effectiveness of the proposed method are demonstrated by an example of stabilizer design for a practical power system.
1988-08-01
A comprehensive condition monitoring system for hydro-electric generating units
Energy Technology Data Exchange (ETDEWEB)
This paper describes a comprehensive MCM [machine condition monitoring] program and suggested system for implementation in hydroelectric generating units. The system addresses all the major subsystems which make up the generating unit. A modular design means that it could be applicable in a wide variety of situations. Different subsystems may be included or excluded from the monitoring system as required. It may be used at individual plants as a stand alone system or network wide. An advanced processing and diagnostic module is included, again for use as an integral part of the system or as a stand alone analysis tool. Examples of the system's proposed data analysis and diagnostic abilities are also described using vibration signals as would be provided by the bearing module. (Author)
1994-04-01
International Nuclear Information System (INIS)
Object: To control the average liquid level of each steam generator at a constant level irrespective of the flow rate of sodium thereby to decrease change in the retained amount of sodium and at the same time to improve the load response characteristic. Construction: A method for decreasing to as large an extent as possible a change in the amount of sodium retained in a steam generator due to change in the flow rate, which comprises the steps of detecting the main recirculating flow rate of liquid sodium by the use of a sodium flow rate detector, amplifying the detected flow rate signal depending upon the ratio between the flow rates respectively in a super-heater and a re-heater (distribution ratio), delivering the amplified signal to a function generator which generates a liquid level setting signal for maintaining the respective average liquid levels of the super-heater and the re-heater at constant ...
International Nuclear Information System (INIS)
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary tests in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The tests aimed at studying the effect of NC gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any NC gas in all cases where cooling is ensured by natural circulation. A secondary objective of the tests - the first series of tests ever performed with NC gas with PACTEL - was to find out, if the instrumentation of PACTEL was adequate for this type of tests and if it was functioning properly. This paper presents the measured and calculated (CATHARE code version V15a mod 2.1) ...
2001-03-20
Thermal hydraulic analysis of nuclear reactors (THEA). THEA summary report
Energy Technology Data Exchange (ETDEWEB)
The project is focused on the thermal hydraulic analyses of nuclear power plants. Specific areas of research have been the modelling of heat transfer in horizontal steam generator in presence of non-condensable gas, and the development of tools for multidimensional two-phase flow simulations. The effect of non-condensable gas on the heat transfer in the horizontal steam generator (SG) has been studied by calculating with APROS the PACTEL experiments NCG-1 (air injection) and NCG-3 (helium injection). The work done for the two-phase flow model development consists of two parts; improving the solution algorithm of porous media code PORFLO, and adding a homogeneous two-phase model to the commercial CFD code Fluent. (orig.)
2004-07-01
Low-range flowmeters for use with vacuum and leak standards
Energy Technology Data Exchange (ETDEWEB)
Vacuum pressure standards of the orifice-flow type require known gas flows of 10/sup -6/ mol/s (10/sup -2/ atm cm/sup 3//s at 0 /sup 0/C) and less. Known gas flows can also be used to calibrate ''standard'' leaks by comparing the pressures generated when flows from the leak and the flowmeter are alternately passed through a constant conductance. Two constant-pressure, piston displacement flowmeters developed at the National Bureau of Standards are described that can generate flows between 10/sup -6/ and 10/sup -10/ mol/s with an estimated uncertainty of 0.8% to 2%. Comparisons of the flowmeters with alternate calibration techniques, and repeated low-range leak and vacuum gauge calibrations, have been used to confirm the estimated uncertainty and random errors of the flowmeter.
1987-05-01
Design and field trial application of foam in production wells to improve conformance
Energy Technology Data Exchange (ETDEWEB)
Many of the vertical hydrocarbon miscible floods in the Keg River carbonate reefs of the Rainbow Field are at a mature stage of reservoir depletion, and are characterized by thin oil sandwiches. Injection of a gas-blocking foam barrier into a gas cone had the potential to improve oil productivity. Experimental foam treatments were described for two wells, each in a different miscible flood well. One of the wells received foam in an aqueous solution to generate foam in-situ, and as a surface generated foam. These attempt were unsuccessful at improving well performance. The second well was injected with preformed foam only. This treatment reduced GOR and improved oil production over a 14 month period. Field experience from these field trials was expected to improve efficiency in planning, design, implementation and evaluation of future foam projects.
1995-05-01
Characterization of Filter Elements for Service in a Coal Gasification Environment
Energy Technology Data Exchange (ETDEWEB)
The Power Systems Development Facility (PSDF) is a joint Department of Energy/Industry sponsored engineering-scale facility for testing advanced coal-based power generation technologies. High temperature, high pressure gas cleaning is critical to many of these advanced technologies. Barrier filter elements that can operate continuously for nearly 9000 hours are required for a successful gas cleaning system for use in commercial power generation. Since late 1999, the Kellogg Brown & Root Transport reactor at the PSDF has been operated in gasification mode. This paper describes the test results for filter elements operating in the Siemens-Westinghouse particle collection device (PCD) with the Transport reactor in gasification mode. Operating conditions in the PCD have varied during gasification operation as described elsewhere in these proceedings (Martin et al, 2002).
2002-09-19
Energy Technology Data Exchange (ETDEWEB)
A new method of plasma treatment for powder particles was investigated. A glass bottle horizontally held on a rotating system was used for the treatment. The outside of the bottle was covered by the grounded metal net, and the rod electrode was provided at the center of the bottle, which was connected to an ac high voltage source. Powder particles were placed in the bottle with stainless steel beads of large diameter and the plasma was generated between two electrodes and while the bottle was rotating. Using this system, powder particles were uniformly plasma-treated without coagulation. After 40 seconds treatment with plasma of 0.55 W in Ar gas, the charge to mass ratio for polyethylene powder particles having 160 {mu}m mean diameter generated by stainless before treatment. (author)
2000-03-31
British Library Electronic Table of Contents (United Kingdom)
In this context, the bulk ratio of CH4/N2 is examined as a potential alternative geochemical parameter for the assessment of thermal maturity of natural gas and compared to other previously published data. Open-system non-isothermal pyrolysis of low-mature coal from the Manjiaer sag, Tarim basin, yielded generation curves for methane and nitrogen. Analysis of the change of vitrinite reflectance indicates a two-stage process of thermal maturation with increasing temperatures. The relationship between Ro and pyrolysis temperature could be expressed by the following equations: Stage I: Ro = 0.0014T + 0.109, r = 0.9931(Ro Ro = 0.0067T -1.5855, r = 0.9996 (Ro > 0.6%). A kinetic interpretation of the characteristics of nitrogen and methane generation in humic coal during laboratory pyrolysis ind...
2008-01-01
Dynamic interpretation of organic-matter maturation and evolution of oil-generative window
Energy Technology Data Exchange (ETDEWEB)
Two phases are recognized in the maturation of organic matter and evolution of the oil-generative window (OGW): (a) a basinal subsidence phase during which potential source rocks undergo burial through a static initial OGW, and maturation is due essentially to increasing temperature with depth, and (b) a postsubsidence phase during which the OGW moves vertically upward through the static sedimentary fill, and maturation is due to time effects. Only the final shallow position of OGW can be defined by geochemical indices of maturity. The hydrocarbon generation sequence progresses from bottom to top, beginning with the lighter hydrocarbons (or even thermogenic gas) at the initial OGW at depth, followed by progressively heavier hydrocarbons as the OGW moves vertically upward. This dynamic model of hydrocarbon generation permits modeling of past positions of OGW relative to basin evolution through ...
1984-08-01
IEA Statistics 1993: electricity information
International Nuclear Information System (INIS)
Gross electricity production in 1993 in the OECD (including generation from pumped storage plants) was 7 466 TWh, a rise of 1.2 per cent from the level of gross production in 1992 (Tables 1 and 3). Nuclear plants accounted for 24.2 per cent of total gross electricity production in 1993, hydroelectric plants 16.7 per cent, total thermal plants 58.7 per cent and geothermal and other renewables 0.4 per cent. In 1992 total OECD heat production that is sold to third parties by public producers was 25 Mtoe (Table 6). About 86 per cent of this heat (21.6 Mtoe) was produced in CHP plants, about 12 per cent (3.1 Mtoe) in heat plants, and the remainder (0.3 Mtoe) in nuclear power plants (in Canada and Switzerland only). Based on preliminary data, apparent consumption of electricity (gross production plus imports less exports) in 1993 in OECD was 7 474 TWh. The corresponding figure for 1992 was 7 379 TWh, ...
1993-01-01
The market potential for SMES in electric utility applications. Final report
Energy Technology Data Exchange (ETDEWEB)
Superconducting magnetic energy storage (SMES) is an emerging technology with features that are potentially attractive in electric utility applications. This study evaluates the potential for SMES technology in the generation, transmission, distribution, and use of electric energy; the time frame of the assessment is through the year 2030. Comparisons are made with other technology options, including both commercially available and advanced systems such as various peaking generation technologies, transmission stability improvement technologies, and power quality enhancement devices. The methodology used for this study focused on the needs of the market place, the capabilities of S and the characteristics of the competing technologies. There is widespread interest within utilities for the development of SMES technology, but there is no general consensus regarding the most attractive size. Considerable ...
1994-06-01
Low-temperature brown rice storage by using renewable energy from snow
Energy Technology Data Exchange (ETDEWEB)
This paper reported on a study that was conducted in Japan to determine whether renewable energy generated from snow can be used to replace the cooling system and electricity used for cooling a rice storehouse that maintained the grain temperature below 15 degrees C. However, the low-temperature storage system required a cooling system and electricity to cool rice in summer. In this study, a snow pile using 890 t of snow was made at the beginning of March next to the rice storehouse. The shape of the snow pile was a trapezium, 17 x 23 m at the bottom and 4 x 10 m at the top and 5 m in height. The snow pile was covered with 200 to 300 mm of wood chips to act as an insulation layer. Approximately 27 per cent of the energy for cooling the rice storehouse could be replaced by using the snow pile in summer. The quality of stored rice was almost similar to that of freshly harvested rice. The study showed that renewable energy ...
2010-07-01
Energy Technology Data Exchange (ETDEWEB)
An investigation was carried out to determine the significance of a large input of cogeneration units for the electric power generation, next to the input of coal and uranium. Thereto a production plant has been set up to generate heat and electric power. The plant serves as a basis for a number of comparative calculations: basic calculations to investigate the influence of some strategies on the cogeneration input, and sensitivity calculations to determine the influence of a few changes in the starting points. Some variants have been deduced from this plant, which is based on prognosis for the year 2000. By means of the computer calculation program OPINIE (Optimale Inzet en Instelling van Eenheden: Optimal Input and Installation of Units) the minimal variable costs were calculated for different situations. Finally for each considered situation the total annual costs have been calculated. 53 figs., 13 ...
1987-02-01
Regulation of electricity prices?
International Nuclear Information System (INIS)
In this paper author deals with the regulation of electricity prices in the Slovak Republic. Author contests the social policy of the government through doped prices of electricity. Two thirds of electricity is generated in nuclear power plants in Slovakia. Hence, it is necessary to focus on the solution of problem of nuclear waste. In 2004 Ministry of Economy stated, that the deficit in nuclear fund, from which the country have to fully cover the costs of liquidation and final disposal of nuclear waste, is estimated in the amount of around 89 billion Slovak crowns (? 3.7 billion $). From it, so called historical deficit, which originated because of late foundation of fund, represents officially 15 billion Slovak crowns (? 0.62 billion $). In Slovakia exists the real risk, that by maintenance of present state by creation and draw of the fund, it will be possible to ensure only 39 per cent of financial ...
2006-12-21
Energy Technology Data Exchange (ETDEWEB)
Several technological alternatives have been studied taking into consideration that one of the biggest problems of the electric power companies is to provide electric power during the peak consumption periods, which largest contribution to the increase of the demand comes from the residential sector, especially by the use of electric showers. One of the most promising alternatives is the pre-water heating system for reduced power showers, developed by Universidade de Campinas and Companhia Paulista de Forca e Luz. The goal of this system is basically to reduce demand during the peak periods, in order to avoid heavy investments by the electric power companies in generation, transmission and distribution of electric power directed to low acquisitive power customers, a sector in which the electric power price is not enough to recover such ...
1996-12-31
International Nuclear Information System (INIS)
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary experiments in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The experiments were run on the Parallel Channel Test Loop (PACTEL), which is a medium scale integral test facility designed to simulate thermal-hydraulic phenomena characteristic of VVER 440 type nuclear plants. The experiments aimed at studying the effect of noncondensable gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators (ACCU) released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any noncondensable gas in all cases where cooling is ensured by natural circulation. This paper presents the measured results of the series of three ...
2001-03-20
Tunable VUV generation by anti-Stokes stimulated Raman conversion of XeCl laser radiation
Energy Technology Data Exchange (ETDEWEB)
This paper reports on the results of experiments into efficient higher-order anti-Stokes Raman conversion of tunable short-pulse XeCl laser radiation. The maximum output energy of the pumping laser, in which the radiation of a frequency-doubled dye laser is amplified by two XeCl laser amplifiers, is 55 mJ with a pulse duration of 1 ns FWHM. Using hydrogen gas as a Raman medium, a series of anti-Stokes lines up to the 12th order (121.5 nm) is generated in the vacuum ultraviolet (VUV) region. 16 references.
1987-06-01
Gas turbine applications in the drying industry
Energy Technology Data Exchange (ETDEWEB)
The purpose of this report is to determine if it is feasible to utilize the hot exhaust gas discharged from gas turbines in direct applications. This report illustrates the technical feasibility and economic viability of using gas turbines in drying applications. The size of turbines in this investigation ranges from 2 MW to 10 MW. In addition, an implementation strategy has been developed to employ this new system. The method used to structure the scope of this undertaking is as follows: Step 1. Collecting information by contacting dryer manufacturer and companies drying different products. Information was also gathered by literature studies and the internet. Thomas register is a great tool when it comes to company and market searches. Step 2. Looking into if it is technically possible to use the exhaust gas directly into dryers. The parameters needed for these calculations were gathered in step 1, and ...
2000-07-01
Probabilistic power generation planning with environmental consideration for Lebanon
International Nuclear Information System (INIS)
Full text.This paper describes a software tool for generation expansion planning based on dynamic programming, probabilistic production simulation, and environmental assessment. The aim is to determine the units needed to expand a given system in order to minimize either the cost or the environmental impact or some weighed function of the two. The problem of generation expansion planning is solved in stages using Tunnel Dynamic Programming (TDP) with Heuristic rules to limit the number of options analyzed. The production costing methodology is based on combining a probabilistic generation model known as the capacity outage table (COT) with the load duration curve (LDC) of the system to deduce a risk model from which the expected energy not supplied (EENS) is estimated. The generation model is built recursively using an efficient numerical convolution procedure and is combined at each step with the LDC ...
2000-11-23
News from the world; Echos du monde
Energy Technology Data Exchange (ETDEWEB)
This document gathers a series of very short articles concerning nuclear industry around the world. Areva company is investing 30 million euros in its Chalon-Saint-Marcel plant, it is the consequence of the extension of service life of nuclear power plants in the Usa. Areva holds 40% of the American market concerning the replacement of steam generators and 50% of that concerning the replacement of closure heads. The Obrigheim nuclear power plant was definitely closed down on may 2004, this decommissioning is a step forward in the German policy of progressively stepping out of nuclear energy. Chinese authorities are willing to construct 40 nuclear reactors in 15 years, despite that, the contribution of nuclear energy to the generation of electricity will reach only 4% in 2020. In 2007 Cea will begin the construction works of a new research reactor (Jules Horowitz reactor) in the Cadarache site. Prices of the yellow cake have ...
2005-04-01
High-efficiency Hybrid Solar Cells for Micro-generation
Environmental Research Database
Objectives1. To develop new photoactive materials and fabricate demonstration QD (quantum dot) solar cells. This will be achieved by:~%~1.1. Materials preparation and characterisation of QD/polymer systems~%~1.2. Optimising structures of QDs, nanorods and polymer for quantum yield and charge transfer~%~1.3 Fabricating demonstration QD/polymer solar cells and measuring power conversion efficiencies~%~2. To demonstrate multiexciton generation (MEG) and harvesting within nanostructured QDs. This will involv [continued...]DescriptionWidespread implementation of photovoltaic electricity to meet changing energy demands requires a step-change in the cost of photovoltaic power. This proposal assembles a consortium of chemists, physicists, materials scientists and electrical engineers from The University of Manchester and Imperial College London to address this need through the development of new low-cost, high-efficiency, ...
2010-01-30
Four materials, carbon felt cube (CFC), granular graphite (GG), granular activated carbon (GAC) and granular semicoke (GS) were tested as packed anodic materials to seek a potentially practical material for microbial fuel cells (MFCs). The microbial community and its correlation with the electricity generation performance of MFCs were explored. The maximum power density was found in GAC, followed by CFC, GG and GS. In GAC and CFC packed MFCs, Geobacter was the dominating genus, while Azospira was the most populous group in GG. Results further indicated that GAC was the most favorable for Geobacter adherence and growth, and the maximum power densities had positive correlation with the total biomass and the relative abundance of Geobacter, but without apparent correlation with the microbial diversity. Due to the low content of Geobacter in GS, power generated in this system may be attributed to other microorganisms such as ...
2011-09-20
Electric field measurement on time domain generated by corona on insulators on distribution systems
Energy Technology Data Exchange (ETDEWEB)
Radio interference and TV interference are being a problem in urban and rural areas. This interference is generated by high voltage transmission lines as well as distribution lines. The radio noise can be produced by polluted or damaged insulators, and by metal parts of the distribution lines. The corona effect on the surface of the dielectric material produces high frequency electromagnetic fields during the ionization and during the recombination period. Fields of different intensity are produced by positive voltage and negative voltage. The insulator flashover (leaking current) also produces electromagnetic fields. A new technique to measure these fields was developed. This technique measures the radiated fields on time domain and on frequency domain. This permits us to characterize the radiated field and thus identify the type of the source. Several measurements were done varying the type of the RF generator, i.e., new insulator and broken ...
1996-12-31
Energy Technology Data Exchange (ETDEWEB)
The Tennessee Valley Authority (TVA), the Electric Power Research Institute (EPRI), and the Department of Energy-National Energy Technologies Laboratory (DOE-NETL) are evaluating and demonstrating integration of terrestrial carbon sequestration techniques at a coal-fired electric power plant through the use of Flue Gas Desulfurization (FGD) system gypsum as a soil amendment and mulch, and coal fly ash pond process water for periodic irrigation. From January to March 2002, the Project Team initiated the construction of a 40 ha Carbon Capture and Water Emissions Treatment System (CCWESTRS) near TVA's Paradise Fossil Plant on marginally reclaimed surface coal mine lands in Kentucky. The CCWESTRS is growing commercial grade trees and cover crops and is expected to sequester 1.5-2.0 MT/ha carbon per year over a 20-year period. The concept could be used to meet a portion of the timber industry's needs while ...
2005-08-30
Process for the recirculation of nitrogen oxides
Energy Technology Data Exchange (ETDEWEB)
The invention is regeneration and recirculation of nitrogen oxides in the exhaust gas of a nitric acid plant without using any material current and heat energy other than that generated in the process of producing nitric acid. Nitrogen oxide is recovered by at least two adsorbers each containing an acid resistant zeolite molecular sieve and operating in an alternate heat cycle; adsorption occurring at 20-40 degrees C and regeneration at 300-350 degrees C. The hot gas exiting from the oxidation U used in the production of nitric acid is used to regenerate the adsorbers and the nitrogen oxides set free during the said regeneration are introduced into the main feed stream of the nitric acid plant. In the final stage of the regeneration the adsorbers are cooled by rinsing them with exhaust gas or air at a temperature of 20-40 degrees C.
1983-01-04
On appraising alternative power plant investment proposals. Pt. 2: Application
Energy Technology Data Exchange (ETDEWEB)
This paper is an application of the economic model developed in Part 1 and programmed in the computer code PEACES (program for the economic analysis of combined energy systems). A case study is presented in which hypothetical energy requirements at an industrial site are considered and an exercise is conducted wherein cogeneration is considered as a means of improving the energy situation at the site. Appropriate technologies that can satisfy the cogeneration requirements are investigated and technical and economic evaluations are carried out for a feasibility assessment. Of the three proposals considered, the gas turbine with heat recovery steam generator and the gas/steam turbine combined cycle cogeneration plant were found to be economically viable, while the steam turbine was not. It was recommended that the gas/steam turbine combined cycle cogeneration proposal be adopted, as it was the most ...
2000-12-01
Headspace gas chromatographic method for determination of methyl bromide in food ingredients
Energy Technology Data Exchange (ETDEWEB)
A headspace gas chromatographic (GC) method, which can be automated, has been developed for determination of methyl bromide. This method has been applied to wheat, flour, cocoa, and peanuts. Samples to be analyzed are placed in headspace sample vials, water is added, and the vials are sealed with Teflon-lined septa. After an appropriate equilibration time at 32 degrees C, the samples are analyzed within 10 h. A sample of the headspace is withdrawn and analyzed on a gas chromatograph equipped with an electron capture detector (ECD). Methyl bromide levels were quantitated by comparison of peak area with a standard. The standard was generated by adding a known amount of methyl bromide to a portion of the matrix being analyzed and which was known to be methyl bromide free. The detection limit of the method was 0.4 ppb. The coefficient of variation (CV) was 6.5% for wheat, 8.3% for flour, 3.3% for cocoa, and 11.6% for peanuts.
1985-11-01
An assessment study of the sea water scrubbing process for flue gas desulfurization has been made by SINTEF. This project has been financially supported by the Royal Ministry of Environment of Norway. The study is based on three FGD-units which are installed at three oil-fired, industrial boilers respectively with a maximum continuous heat input of 130 MW (27 MW + 2x51.5 MW) corresponding to approximately 50 MWE (10 MWE + 2x20 MWE) generating capacity for a power plant having a net efficiency of 38%.
1979-01-01
The purpose of this rulemaking is to amend the effluent limitations guidelines and standards for the control of discharges of certain pollutants associated with the use of synthetic-based drilling fluids (SBFs) and other non-aqueous drilling fluids in portions of the Offshore Subcategory and Cook Inlet portion of the Coastal Subcategory of the Oil and Gas Extraction Point Source Category. These proposed limitations apply to discharges or effluent generated when oil and gas wells are drilled using SBFs or other non-aqueous drilling fluids (collectively referred to simply as SBFs) in coastal and offshore regions in locations where drilling wastes may be discharged.
1999-02-01
CSSX Radiolytic H2 Generation ("Thermolysis") -- Final Report
Energy Technology Data Exchange (ETDEWEB)
The purpose of this work was to determine the radiolytic hydrogen gas yield of irradiated CSSX solvent at several temperatures. The active ingredient of this solvent is calix[4]arene-bis-(t-octylbenzo) crown-6, a calixarene crown ether used for cesium complexation. The solvent also contains 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol, a fluorinated alcoholic solvent modifer used to improve the solubility of the calixarene and its cesium complex in the Isopar L diluent. Isopar L is a branch-chain alkane and comprises most of the mixture. Samples of this solution were irradiated to various absorbed ?-ray doses in gas-tight sample containers, which were then sampled for hydrogen gas content. The methods are described below.
2009-01-01
Frequency Controlled Electric Drives
International Science & Technology Center (ISTC)
Development of Frequency Controlled Electric Drives
Status of non-electric nuclear heat applications: Technology and safety
International Nuclear Information System (INIS)
Nuclear energy plays an important role in electricity generation, producing 16% of the world's electricity at the beginning of 1999. It has proven to be safe, reliable, economical and has only a minimal impact on the environment. Most of the world's energy consumption, however, is in the form of heat. The market potential for nuclear heat was recognized early. Some of the first reactors were used for heat supply, e.g. Calder Hall (United Kingdom), Obninsk (Russian Federation), and Agesta (Sweden). Now, over 60 reactors are supplying heat for district heating, industrial processes and seawater desalination. But the nuclear option could be better deployed if it would provide a larger share of the heat market. In particular, seawater desalination using nuclear heat is of increasing interest to some IAEA Member States. In consideration of the growing experience being accumulated, the IAEA periodically reviews the progress and ...
International water power and dam construction handbook
Energy Technology Data Exchange (ETDEWEB)
The first section of this Handbook describes hydro-electric projects currently under construction or recently commissioned in a number of countries. The major part of the Handbook is devoted to lists of data relating to hydro-electric plants and hydromachinery. These include: data for 1990 submitted by national power authorities on hydro-electric and pumped-storage plants in operation, under construction or planned; more detailed data for pumped-storage plants; country by country data on the dimensions, and reservoir and electrical capacity of major dams and hydro plant; a listing of roller compacted concrete dams; a listing of the world's largest turbines giving data on the largest unit at each scheme in rank order ranging from a unit capacity of 838 MV down to 147 MV; a similar list of the largest hydrogenerators ranging from a unit capacity of 825 MVA down to 150 MVA; details of turbine and ...
1992-01-01
Upper Paleozoic petroleum system, Ordos Basin, China
Energy Technology Data Exchange (ETDEWEB)
The Ordos Basin is a typical lapped basin, including three sequences of strata: early Paleozoic, late Paleozoic and Mesozoic, with a total thickness of 4000-6000m. Impermeable sealing beds are well developed at the top and base of the upper Paleozoic sequence, separating it from the Mesozoic and the lower Paleozoic strata to form an independent petroleum system. In this petroleum system, the source rocks are widely distributed coals and dark mudstones occurring in the Carboniferous-lower Permian coal measures, with a thickness of 10-15 and 40-60m, respectively. The reservoirs are mainly early Permian tight sandstones, mostly with a porosity of 4-8% and a permeability of 0.1-1.0x10{sup -3}{mu}m{sup 2}. The regional cap rock is a 100-150m thick mudstone in the upper Permian strata. The structural framework of the basin is a huge asymmetric syncline, dipping gently toward the east and north, and steeply toward the south and west. Well data show that gas-saturated, ...
2005-09-01
High-pressure ceramic air heater for indirectly fired gas turbine applications
Energy Technology Data Exchange (ETDEWEB)
The Externally-Fired Combined Cycle (EFCC) offers a method for operating high-efficiency gas and steam turbine combined cycles on coal. In the EFCC, an air heater replaces the gas turbine combustor so that the turbine can be indirectly fired. Ceramic materials are required for the heat exchange surfaces to accommodate the operating temperatures of modern gas turbines. The ceramic air heater or heat exchanger is the focus of this program, and the two primary objectives are (1) to demonstrate that a ceramic air heater can be reliably pressurized to a level of 225 psia (1.5 MPa); and (2) to show that the air heater can withstand exposure to the products of coal combustion at elevated temperatures. By replacing the gas turbine combustor with a ceramic air heater, the cycle can use coal or other ash-bearing fuels. Numerous programs have attempted to fuel high efficiency gas turbines ...
1992-01-01
High-pressure ceramic air heater for indirectly fired gas turbine applications
Energy Technology Data Exchange (ETDEWEB)
The Externally-Fired Combined Cycle (EFCC) offers a method for operating high-efficiency gas and steam turbine combined cycles on coal. In the EFCC, an air heater replaces the gas turbine combustor so that the turbine can be indirectly fired. Ceramic materials are required for the heat exchange surfaces to accommodate the operating temperatures of modern gas turbines. The ceramic air heater or heat exchanger is the focus of this program, and the two primary objectives are (1) to demonstrate that a ceramic air heater can be reliably pressurized to a level of 225 psia (1.5 MPa); and (2) to show that the air heater can withstand exposure to the products of coal combustion at elevated temperatures. By replacing the gas turbine combustor with a ceramic air heater, the cycle can use coal or other ash-bearing fuels. Numerous programs have attempted to fuel high efficiency gas turbines ...
1992-12-01
Heat transfer augmentation by gas-particle two-phase flow
International Nuclear Information System (INIS)
The helium-cooled HTGR (High Temperature Gas-cooled Reactor) will take an important position in the global energy strategy. It is expected to supply not only electricity but also high quality thermal energy for various industries and local utilities without exhausting any green house effect gas or acid rain gas. The key R and D issue of the HTGR is economical competitiveness, particularly against light water reactors. Due to the poor heat transfer of the single phase helium, the HTGR's volumetric power density is restricted to tenth of corresponding PWR's value so that increasing the power density by improving heat transfer is strongly desired. The standstill can be broken through by adopting gas-solid suspension medium. Its heat transfer performance is quite excellent. Its heat capacity can be increased drastically without excessive pressurization. Although the thermal radiation is ...
1995-06-01
The non-blast furnace coke produced in the shaft ovens of the Angarsk Semi-coking Plant is used principally in gas generator ovens and partially as a carbonaceous reducing agent in the ferroalloy process. The sulfur content of this coke is not limited by the standards documents, but it is significant, especially in the production of process gases. In a number of recent years the sulfur removal system of the gasification divisions have been experiencing difficulties, not achieving the assigned gas purification parameters, with a resulting H/sub 2/S concentration in the purified gas of 300-700 mg/m/sup 3/ as compared to the standard of 50. Realizing that in the gasification practically all the organic matter of the coke, including the sulfur, enters the gas, the impairment in the quality of the sulfur removal is related to the increase in the sulfur content of the coke. Thus, an ...
1984-01-01
Direct coal-fired gas turbines for combined cycle plants
Energy Technology Data Exchange (ETDEWEB)
The combustion/emissions control island of the CFTCC plant produces cleaned coal combustion gases for expansion in the gas turbine. The gases are cleaned to protect the turbine from flow-path degeneration due to coal contaminants and to reduce environmental emissions to comparable or lower levels than alternate clean coal power plant tedmologies. An advantage of the CFTCC system over other clean coal technologies using gas turbines results from the CFTCC system having been designed as an adaptation to coal of a natural gas-fired combined cycle plant. Gas turbines are built for compactness and simplicity. The RQL combustor is designed using gas turbine combustion technology rather than process plant reactor technology used in other pressurized coal systems. The result is simpler and more compact combustion equipment than for alternate technologies. The natural effect is lower cost ...
1993-11-01
Making the case for grid-connected photovoltaics in Brazil
International Nuclear Information System (INIS)
In the developed world, grid-connected photovoltaics (PVs) are the fastest-growing segment of the energy market. From 1999 to 2009, this industry had a 42% compound annual growth-rate. From 2009 to 2013, it is expected to grow to 45%, and in 2013 the achievement of grid parity - when the cost of solar electricity becomes competitive with conventional retail (including taxes and charges) grid-supplied electricity - is expected in many places worldwide. Grid-connected PV is usually perceived as an energy technology for developed countries, whereas isolated, stand-alone PV is considered as more suited for applications in developing nations, where so many individuals still lack access to electricity. This rationale is based on the still high costs of PV when compared with conventional electricity. We make the case for grid-connected PV generation in Brazil, showing that with the ...
2011-03-01
Energy Technology Data Exchange (ETDEWEB)
Decontamination and decommission activities related to the Molten Salt Reactor Experiment (MSRE) involve the trapping and recovery of radiolitically generated uranium hexafluoride and fluorine. Although fission product radiolysis was known to generate F{sub 2}, the formation of UF{sub 6} and its transport from the fuel salt was unexpected. Some of these gaseous radiolysis products have been moving through the gas piping to a charcoal bed since the reactor was shut down in 1969. Current and planned remediation and clean-up activities involve the trapping of the gaseous products, deactivation and treatment of the activated charcoal bed, stabilization and reconditioning of the fuel salt, and recovery of the uranium. The chemical aspects of these processes, including radiolytic generation mechanisms, reactions between uranium hexafluoride and fluorine and trapping materials such as activated charcoal, ...
1996-10-01
The effect of H_2S on molten carbonate fuel cells
International Nuclear Information System (INIS)
Although molten carbonate fuel cells (MCFC) have been under development since the late 1950s, the operating characteristics with gases derived from coal containing a wide range of elements other than C, H, and O were not studied until the Energy Conversion Alternative Study (ECAS) was completed in the late 1970s. Since then, the work of each contractor (United Technologies, Institute of Gas Technology, General Electric, and Energy Research Corporation) has included some contaminant studies (primarily of sulfur compounds). The majority of the reported work appears to have been conducted by UTC and IGT. The results indicate that the MCFC requires removal of sulfur to ppm levels. However, because of the strong dependence on temperature, pressure, gas composition, gas utilization, cell components, and system operation (i.e. recycle, venting, gas cleanup), the tolerance limits can vary ...
Energy Technology Data Exchange (ETDEWEB)
In this study, sensitivity analysis of 100 MWth chemical looping combustion combined cycle (CLC-CC) plant based on fuel cost were performed. By performance analysis, net efficiency of natural gas/syngas fueled CLC-CC plant was 53-54%, corresponding to previous research. We used Chemical Engineering Plant Cost Index and Guthrie method to evaluate plant cost. For syngas fueled CLC-CC plant, the plant cost was higher since lower heating value (LHV) of syngas was lower than that of natural gas and cost of electricity (COE) was also higher since the cost of syngas was higher than that of natural gas. By sensitivity analysis, it was shown that the cost of syngas should be less than 5.3 $/GJ in order to make COE lower than 5.8 c/kWh which was COE of natural gas CLC-CC plant. 15 refs., 2 figs., 5 tabs.
2009-07-01
Energy Technology Data Exchange (ETDEWEB)
Work on this coke oven gas cleaning demonstration project (CCT-II) this quarter has been focused on Phase IIB tasks, and include engineering, procurement, construction, and training. Additionally, plans for changes in the operating schedule of the coke plant that affect the demonstration project are described. Engineering efforts are nearly complete. Remaining to be finalized is an assessment of electrical heat tracing/insulation needs for pipe lines, assessment of fire protection requirements, and instrument modifications. Procurement of all major equipment items is complete, except for possible additions to fire fighting capabilities. Major focus is on expediting pipe and structural steel to the project site. Civil construction is complete except for minor pads and bases as required for pipe supports, etc. Erection of the hydrogen sulfide and ammonia scrubber vessels is complete. Installation of scrubber vessel internals is underway. A ...
1993-10-22
Evaluation of spark ignition of a gas cooktop flame
One of the energy-saving devices used on gas cooking appliances to eliminate the standing pilot is a spark ignition system. For safety, an ignition system must start promptly and be active whenever flowing gas is not ignited. To minimize noise and nuisance shock hazard, ignition must occur quickly and the sparking must be stopped as soon as ignition occurs and remain off as long as the flame is present. To accomplish both of these requirements, ignition systems have been devised which use the electrical current rectification property of a flame to sense it. These systems spark whenever the gas valve is on and a flame is not present. The factors affecting the performance of a spark ignition system are numerous, complex, and transient. All of these properties make quantification of performance difficult. A system is described which can evaluate the overall performance of ignition systems over significant ...
1996-01-01
Safety testing of 18650-style Li-Ion cells
Energy Technology Data Exchange (ETDEWEB)
To address lithium-ion cell safety issues in demanding power applications, electrical and thermal abuse tests were performed on 18650 sized cells. Video and electrically monitored abuse tests in air included short circuit, forced overcharge, forced reversal, and controlled overheating (thermal) modes. Controlled overheating tests to 200 C were performed in a sealed chamber under a helium atmosphere and the gases released from the cell during thermal runaway were analyzed at regular intervals using gas chromatography and mass spectrometry. In addition to alkane and alkene solvent breakdown fragments, significant H{sub 2} was detected and evidence that HF was evolved was also found.
2000-06-08
Near term and future alternative clean vehicle technologies
Energy Technology Data Exchange (ETDEWEB)
Availability of a natural gas-powered van that meets California`s ultra low emission vehicle requirements and has a 300-km range was reported. A similar van with an electric system giving a range of 240 km was also within sight. Regarding the limitations of electric batteries it was suggested that a super capacitor may allow systems to achieve higher energy densities; a refuelable zinc-air battery could be considered for vehicle use. While the prospect for emissions improvement of gasoline vehicles has clearly improved in recent years, the relative costs of infrastructure, vehicle and fuel for the the alternative fuels compared with gasoline demonstrate the difficulty the alternative fuels have in taking market share from gasoline. For the next decade, gasoline, propane and CNG are expected to be the dominant fuels for vehicles. After that, the leading fuel will be the one that has been most extensively researched and ...
1994-12-31
International Nuclear Information System (INIS)
Nano structured carbon nitride thin films were deposited at different RF powers in the range of 50 W to 225 W and constant gas ratio of (argon: nitrogen) Ar:N_2 by RF magnetron sputtering. The atomic percentage of Nitrogen: Carbon (N/C) content and impedance of the films increased from 14.36% to 22.31% and 9 x 10"-"1 #OMEGA# to 7 x 10"5 #OMEGA# respectively with increase in RF power. The hardness of the deposited films increased from 3.12 GPa to 13.12 GPa. The increase in sp"3 hybridized C-N sites and decrease of grain size with increase in RF power is responsible for such variation of observed mechanical and electrical properties.
2010-10-01
A Reduced Wind Power Grid Model for Research and Education
Energy Technology Data Exchange (ETDEWEB)
A reduced grid model of a transmission system with a number of central power plants, consumption centers, local wind turbines and a large offshore wind farm is developed and implemented in the simulation tool PowerFactory (DIgSILENT). The reduced grid model is given by Energinet.dk, Transmission System Operator of Denmark (TSO) for Natural Gas and Electricity, to the Danish Universities and the Risoe National Laboratory. Its intended usage is education and studying of interaction between electricity-producing wind turbines and a realistic transmission system. Focus in these studies is on voltage stability issues and on the ride-through capability of different wind turbine concepts, equipped with advanced controllers, developed by the Risoe National Laboratory.
2006-07-01
Low-Cost Hydrogen Distributed Production System Development
H{sub 2}Gen, with the support of the Department of Energy, successfully designed, built and field-tested two steam methane reformers with 578 kg/day capacity, which has now become a standard commercial product serving customers in the specialty metals and PV manufacturing businesses. We demonstrated that this reformer/PSA system, when combined with compression, storage and dispensing (CSD) equipment could produce hydrogen that is already cost-competitive with gasoline per mile driven in a conventional (non-hybrid) vehicle. We further showed that mass producing this 578 kg/day system in quantities of just 100 units would reduce hydrogen cost per mile approximately 13% below the cost of untaxed gasoline per mile used in a hybrid electric vehicle. If mass produced in quantities of 500 units, hydrogen cost per mile in a FCEV would be 20% below the cost of untaxed gasoline in an HEV in the 2015-2020 time period using EIA fuel cost projections for natural ...
2011-03-10
New approaches to the design of the combustion system for thermophotovoltaic applications
Energy Technology Data Exchange (ETDEWEB)
A thermophotovoltaic (TPV) generator for electric vehicles has been designed and developed. In this paper we focus on the combustion system and the heat regenerator. The system has been designed to work as a range extender for electric vehicles. This solution would provide energy always available on the vehicle, which would run even if the battery level were low. Several configurations for the burner and for the heat exchanger have been investigated and a comparison of these is presented. The different solutions have been studied both theoretically and experimentally. In this paper, we report on the work carried out to build a TPV device capable of yielding 6 kW of electric power to recharge the battery pack of an electric city-car. The project has been divided into four steps: (1) pre-design of different configurations of the burner and heat exchanger using non-commercial software ...
2003-05-01
Energy Technology Data Exchange (ETDEWEB)
The Coal Fired Combined Cycle (CFCC) power system thermodynamic cycle is illustrated schematically. Pressurized air supplied at the discharge of gas turbine compressors is ducted to the pressure vessel of pressurized, fluidized-bed, combustor-steam generator modules. The air is introduced in parallel to the beds, entering through distribution grids beneath each bed. Steam generation tubes are buried within the beds and are also arranged as membrane tube walls enclosing the four sides. Crushed coal (1/4 inch x 0) is pneumatically fed at locations just above the air inlet grids at the bottom of each bed. Dolomite is similarly fed to the individual beds. The coal is burned at a temperature below the ash fusion point. Sulfur is removed in the fluid beds through reaction of the SO/sub 2/ with CaCO/sub 3/ and O/sub 2/ to form solid CaSO/sub 4/ and CO/sub 2/ gas. The combustion gases leave the beds at a ...
1980-05-01
Method of controlling the coolant level in the cooling system of a nuclear power plant
International Nuclear Information System (INIS)
Object: To prevent a sudden drop in the level of a coolant in a annular pipe encased within a downcomer pipe. Structure: The coolant levels in annular pipes encased within downcomer pipes are simultaneously measured by level gauges which generate signals representative of coolant levels. The signals are fed to a level control system which will actuate valves to regulate the cover gas pressure in order to average the level differences among the annular pipes in different downcomer pipes. (Kamimura, M.).
Guide to UK renewable energy companies 2001. 6. ed.
International Nuclear Information System (INIS)
This 2001 edition of the guide to UK renewable companies and equipment and service providers presents summaries of the different industry sectors covering wind power, photovoltaics, solar water heating, geothermal heat pump, hydroelectric power, marine current and wave technology, bioenergy, power generation from landfill gas, energy from waste, and cogeneration. A UK company classification listing and index is provided along with listing of UK organisations and companies and an index of advertisers.
The report is the first full compilation (not a supplement) since the October-December 1980 report (PB81-187783). Because the next three reports are to be supplements, this issue should be retained for reference throughout the year. The report, generated by a computerized data ba...
Coal geology and its application to coal-bed methane reservoirs
Energy Technology Data Exchange (ETDEWEB)
A total of nine papers were presented at the course with the following titles: peat accumulation and coal basins; coal composition; coal quality; sedimentary environments of coal; generation, storage and migration of natural gas in coal bed reservoirs; geophysical log interpretation; the Ardley coal zone of central Alberta; stratigraphy and sedimentary environment of the Coalspur Formation; and the coal-bearing Luscar Group of western Alberta. All of these papers have been abstracted separately.
1990-01-01
Energy Technology Data Exchange (ETDEWEB)
This study aims to evaluate the economic and environmental viability of the exploitation of methane gas (CH4) - biogas - concentrated at the bottom of the mountains of waste from landfill Chapeco for power generation. The landfill receives approximately of 80 tons / day, the vast majority of domestic origin.
2006-07-01
Guide to Combined Heat and Power Systems for Boiler Owners and Operators
Energy Technology Data Exchange (ETDEWEB)
Combined heat and power (CHP) or cogeneration is the sequential production of two forms of useful energy from a single fuel source. In most CHP applications, chemical energy in fuel is converted to both mechanical and thermal energy. The mechanical energy is generally used to generate electricity, while the thermal energy or heat is used to produce steam, hot water, or hot air. Depending on the application, CHP is referred to by various names including Building Cooling, Heating, and Power (BCHP); Cooling, Heating, and Power for Buildings (CHPB); Combined Cooling, Heating, and Power (CCHP); Integrated Energy Systems (IES), or Distributed Energy Resources (DER). The principal technical advantage of a CHP system is its ability to extract more useful energy from fuel compared to traditional energy systems such as conventional power plants that only generate electricity and industrial boiler systems that ...
2004-08-19
Studies of basic parameters of electron-counting detection
International Nuclear Information System (INIS)
Measurements have been made of certain parameters relevant to the operation of electron-counting detectors. An experimental chamber consisting of a uniform-field drift tube and a coaxial proportional counter thas been employed to obtain data, at very low drift fields (E/p<0.02 V/cm Torr), on electron mobility and lifetimes in a range of gas mixtures. These mixtures included argon, methane, nitrogen and carbon dioxide. Measurements of single-electron spectra showed that, unexpectedly for the standard gas mixtures employed, useful departure from an exponential spectrum was not possible without the production of cathode secondaries. Although the present studies employed only the counter electrical signal the information obtained should be directly relevant to the operation of practical light-pulse systems. Examples of electron-counting spectra for soft X-rays are shown. (orig.).
1990-05-21
International Nuclear Information System (INIS)
Lebanon has imported in 1996 5000 Kt of carburants causing about 80 Kt of SO_x; 40 Kt of NO_x; 3 Kt of dusts and 3.5 million tons of CO_2. The atmospheric pollution in Lebanon is due to three main sources: - Thermal central of electric production - Industries (cement) - Transportation sector The document describes in tables: the inventory of pollutants and pollutant emissions in 1993 and 2010; industrial and heating gas oil; liquified petroleum gas commercial propane; fuel oil for EDL; consumption of energy in 1996; sectorial distribution of pollutants PPM; emissions of CO_2 per tons per habitant in 1993; consumption in 1993 broken down by use and application. Finally, three projects concerning public transportation were presented
1999-06-02
Energy Technology Data Exchange (ETDEWEB)
Work on the coke oven gas cleaning demonstration project (CCT-11) this quarter has focused on Phase IIB tasks, and include engineering, construction, and training. Additionally, plans for changes in the operating schedule of the coke plant that affect the demonstration project are described. The project Milestone Schedule and Log is shown. Planned Baseline Supplemental Monitoring activities described in the Environmental Monitoring Plan were completed. Testing of the mechanical systems began in June, 1991. The cold commissioning date has been moved back from October 1, 1991 to November 1, 1991 to allow float for miscellaneous finish-up items beyond the electrical contractor`s projected completion date of October 31, 1991.
1995-05-01
Energy Technology Data Exchange (ETDEWEB)
Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.
1991-12-01
Energy Technology Data Exchange (ETDEWEB)
Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.
1991-12-01
Energy Technology Data Exchange (ETDEWEB)
The ARE progress report discusses the following issues: Economic development and its effects on power supply; Deregulation of the electricity and gas market; Competition between regional utilities; Energy policy of the new German government; European regulations; Legislation on energy supply; Energy supply and cartel law; Regional supply in the East German states. [German] Der Taetigkeitsbericht der ARE befasst sich mit folgenden Themen: Gesamtwirtschaftliche Entwicklung und ihre Auswirkung auf die Energiewirtschaft, Oeffnung des Monopoles fuer Strom und Gas, Wettbewerb der regionalen Energieversorger, Energiepolitik der neuen Bundesregierung, Europaeische Richtlininen, energiewirtschaftsrecht, Versorgungswirtschaft und Kartellrecht und der Regionalversorgung in den neuen Bundeslaendern.
2002-05-01
Progress toward an optimized hydrogen series hybrid engine
Energy Technology Data Exchange (ETDEWEB)
The design considerations and computational fluid dynamics (CFD) modeling of a high efficiency, low emissions, hydrogen-fueled engine for use as the prime mover of a series hybrid automobile is described. The series hybrid automobile uses the engine to generate electrical energy via a lightweight generator, the electrical energy is stored in a power peaking device (like a flywheel or ultracapacitor) and used as required to meet the tractive drive requirements (plus accessory loads) through an electrical motor. The engine/generator is stopped whenever the energy storage device is fully charged. Engine power output required was determined with a vehicle simulation code to be 15 to 20 kW steady state with peak output of 40 to 45 kW for hill climb. Combustion chamber and engine geometry were determined from a critical review of the hydrogen engine experiments in the ...
1995-06-01
Energy Technology Data Exchange (ETDEWEB)
The generation of thermal energy is the great importance for the agribusiness of dairy industry to conservation the quality of milk, taking into account that the electricity is the main source currently used for the thermal energy input. The small agribusiness dairy industry currently practiced in Brazil faces several problems related to the cost of electricity and the distance of rural properties of networks of power. In the current scenario of Brazilian dairy production, there is need for the generation of cold for the milk cooling, and also the heat for the production of hot water around 50 deg C to 60 deg C and also for cleaning of equipment used for milk production and processing. The main objective of this study is the modeling and simulation of integrated recovery process of solid waste, effluents and bioconversion. The specific project objectives are: comparison study of options and ...
2008-07-01
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
