Energy Technology Data Exchange (ETDEWEB)

Pressurized fluidized bed combustion (PFBC) is an emerging coal-fired, combined-cycle power generation technology nearing commercial status through several operating and planned demonstration plants throughout the world. Current-generation PFBC plants use ``ruggedized`` gas turbines that can tolerate dust loading common with conventional cyclone gas cleaning. The next generation of PFBC will apply advanced hot gas cleaning systems that will reuse the dust loading to low levels acceptable to high performance, industrial gas turbines. These advances should result in performance and cost advantages. This article examines the demonstration of PFBC technology at Tidd power station.

Energy Technology Data Exchange (ETDEWEB)

Bethlehem Steel Corporation (BSC), in conjunction with the Department of Energy (DOE) is conducting a Clean Coal Technology (CCT) project at its Sparrows Point, Maryland Coke Oven Plant. This innovative coke oven gas cleaning system combines several existing technologies into an integrated system for removing impurities from Coke Oven Gas (COG) to make it an acceptable fuel. DOE provided cost-sharing under a Cooperative Agreement with BSC. This Cooperative Agreement requires BSC to develop and conduct and Environmental Monitoring Plan for the Clean Coal Technology project and to report the status of the EMP on a quarterly basis. It also requires the preparation of a final report on the results of the Baseline Compliance and Supplemental Sampling Programs that are part of the EMP and which were conducted prior to the startup of the innovative ...

International Nuclear Information System (INIS)

At the Tokai Research Establishment of Japan Atomic Energy Research Institute, the radioactive solid waste incineration unit with a capacity of 100 kg/h was installed in 1979, since then the unit has been routinly operated. An off-gas cleaning system of the unit consists mainly of a primary and secondary ceramic filters, a heat resistant HEPA filter and a scrubber. A series of hot test was carried out to examine the docontamination performance for radionuclides in the off-gas cleaning system. In the test, simulated wastes contaminated with a known quantity of radionuclides were burned in the unit, and radioactive concentrations in the off-gas were measured. And then, the following data were obtained: a retention factor of radionuclides in a furnace and a decontamination factor for radionuclides in each of off-gas ...

Science.gov (United States)

The report describes a computer model developed by TVA to simulate the performance and determine the economics of coal cleaning, or coal cleaning combined with flue gas desulfurization (FGD), for power plant emission control processes over a wide range of user-specified condition...

Energy Technology Data Exchange (ETDEWEB)

The combustion/emissions control island of the CFTCC plant produces cleaned coal combustion gases for expansion in the gas turbine. The gases are cleaned to protect the turbine from flow-path degeneration due to coal contaminants and to reduce environmental emissions to comparable or lower levels than alternate clean coal power plant tedmologies. An advantage of the CFTCC system over other clean coal technologies using gas turbines results from the CFTCC system having been designed as an adaptation to coal of a natural gas-fired combined cycle plant. Gas turbines are built for compactness and simplicity. The RQL combustor is designed using gas turbine combustion technology rather than process plant reactor technology used in other pressurized coal ...

International Nuclear Information System (INIS)

Five fires that occurred in the air and gas treatment systems of U.S. commercial nuclear power plants are reviewed. The causes of the fires, the method of extinguishing them and possible fire prevention methods are correlated with the properties of the adsorbents. The similarities and differences of adsorbent (carbon) fires of solvent recovery systems and the nuclear air-cleaning units are discussed in relation to fire development, consequences of the fire, and fire extinguishing methods. The latest methodology of fire prevention, as proposed for a New Hampshire nuclear power plant is described.

Energy Technology Data Exchange (ETDEWEB)

The coke plant at the Sparrows Point Plant consist of three coke oven batteries and two coal chemical plants. The by-product coke oven gas (COG) consists primarily of hydrogen, methane, carbon monoxide, nitrogen and contaminants consisting of tars, light oils (benzene, toluene, and xylene) hydrogen sulfide, ammonia, water vapor and other hydrocarbons. This raw coke oven gas needs to be cleaned of most of its contaminants before it can be used as a fuel at other operations at the Sparrows Point Plant. In response to environmental concerns, BSC decided to replace much of the existing coke oven gas treatment facilities in the two coal chemical Plants (A and B) with a group of technologies consisting of: Secondary Cooling of the Coke oven Gas; Hydrogen Sulfide Removal; Ammonia Removal; Deacification of Acid Gases Removed; Ammonia Distillation and Destruction; and, Sulfur Recovery. This ...

Energy Technology Data Exchange (ETDEWEB)

Biomass gasification provides the potential to efficiently and economically produce a renewable source of a clean gaseous fuel suitable for power generation or synthesis gas (syngas) applications. An important side benefit of the use of biomass is the effective minimization of the primary greenhouse gas, carbon dioxide (CO{sub 2}), by providing a means to close-loop the CO{sub 2} cycle. However, high molecular weight hydrocarbon constituents (tar) in the product gas from gasification can complicate the downstream uses of the gas. This paper discusses both the development of a low cost, disposable catalyst system that can eliminate these heavy hydrocarbons from the gas and the use of the catalyst in conjunction with the Battelle high-throughput gasification process for power generation and synthesis applications. (author)

Energy Technology Data Exchange (ETDEWEB)

The Power Systems Development Facility (PSDF) is a joint Department of Energy/Industry sponsored engineering-scale facility for testing advanced coal-based power generation technologies. High temperature, high pressure gas cleaning is critical to many of these advanced technologies. Barrier filter elements that can operate continuously for nearly 9000 hours are required for a successful gas cleaning system for use in commercial power generation. Since late 1999, the Kellogg Brown & Root Transport reactor at the PSDF has been operated in gasification mode. This paper describes the test results for filter elements operating in the Siemens-Westinghouse particle collection device (PCD) with the Transport reactor in gasification mode. Operating conditions in the PCD have varied during gasification operation as described elsewhere in these proceedings (Martin et ...

Science.gov (United States)

The manual describes a combined coal-cleaning and flue gas desulfurization (FGD) computerized design and cost-estimate model and gives detailed procedures for using it. All inputs and outputs are described, as well as the various options available. Design and economic premises ar...

Energy Technology Data Exchange (ETDEWEB)

A substantial global market for advanced power systems is expected to develop early in the next century for both repowering and new capacity additions, Although natural gas-fueled systems, such as gas turbines, are expected to dominate in the 1990`s, coal-fueled systems are expected to emerge in the 2000`s as systems of choice for base-load capacity because of coal`s lower expected cost. Stringent environmental regulations dictate that all advanced power systems must be clean, economical, and efficient in order to meet both the environmental and economic performance criteria of the future. Recognizing these needs, the DOE strategy is to carry out an effective RD&D program, in partnership with the private sector, to demonstrate these technologies for commercial applications in the next century. These technologies are ...

Energy Technology Data Exchange (ETDEWEB)

One of the five projects selected for funding within the Clean Coal Technology Program is a project proposed by the Pennsylvania Electric Company (Penelec) of Johnstown, Pennsylvania. Penelec proposes to enter into a cooperative agreement with DOE to design, construct and operate a 600 ton-per-day, 66-megawatt (MWe), coal-fueled, externally-fired combined cycle (EFCC) electric power generation facility. The EFCC is an emerging technology with promise for operating highefficiency combined gas- and steam-turbine cycles on coal. The central feature of EFCC is its coupling of the gas turbine to an external, atmospheric-pressure, coal combustor via a hightemperature ceramic heat exchanger (CerHx{reg_sign}) developed by Hague International. The EFCC technology is attractive because, unlike competing combined cycles such as Integrated Gasification (IGCC) and Pressurized Fluidized Bed Combustion (PFBC), it eliminates the need for a ...

Energy Technology Data Exchange (ETDEWEB)

The combination of wood gasification and high temperature fuel cells like solid oxide fuel cells (SOFC) is an interesting approach to achieve high electrical efficiencies (40%) in small scale combined heat and power plants. This combination is called 'Biomass - Integrated Gasification Fuel Cell System' (B-IGFC). The main challenge is the adjustment of the three main components gasification, gas cleaning and fuel cell. In this technology, the first proof of principle by combining a gasifier with a SOFC in a laboratory scale for more than 100 hours was achieved. During this period, no deactivation of the system was found. (author)

International Nuclear Information System (INIS)

This paper reports that there are four combustion technologies upon which U.S. electric utilities are expected to rely for the majority of their future power generating needs. These technologies are pulverized coal- fired combustion (PC); coal-fired fluidized bed combustion (AFBC); coal gasification, combined cycle systems (CGCC); and natural gas-fired combined cycle systems (NGCC). The engineering and economic parameters which affect the choice of a technology include capital costs, operating and maintenance costs, fuel costs, construction schedule, process risk, environmental and site impacts, fuel efficiency and flexibility, plant availability, capacity factors, timing of startup, and the importance of utility economic and financial factors.

Energy Technology Data Exchange (ETDEWEB)

The Externally-Fired Combined Cycle (EFCC) is an attractive emerging technology for powering high efficiency combined gas and steam turbine cycles with coal or other ash bearing fuels. In the EFCC, the heat input to a gas turbine is supplied indirectly through a ceramic air heater. The air heater, along with an atmospheric coal combustor and ancillary equipment, replaces the conventional gas turbine combustor. A steam generator located downstream from the ceramic air heater and steam turbine cycle, along with an exhaust cleanup system, completes the combined cycle. A key element of the EFCC Development Program, the 25 MMBtu/h heat-input Kennebunk Test Facility (KTF), has recently begun operation. The KTF has been operating with natural gas and will begin operating with coal in early 1995. The US Department of Energy selected an EFCC repowering of the Pennsylvania Electric Company`s ...

Energy Technology Data Exchange (ETDEWEB)

The most effective way to generate electricity out of biomass is the gasification and the use of the gas in a gas engine. The conversion of the organic carbon with the gasification of biomass is higher than 95 %. Depending on the gasification concept, the efficiency of gasifiers is found between 70 and 90 %. If the pyrolysis gas is used in a gas engine, an electric efficiency of about 26 % referring to the primary amount of energy can be obtained. With efficient gas cleaning (cleaning for tar and dust), pyrolysis gas is well qualified for engine combustion. Through modern state of engine controlling there are ways to have complete control of the fluctuations in the gas composition. Furthermore, the minor calorific value of offered wood gas poses no problem for turbo charged ...

Energy Technology Data Exchange (ETDEWEB)

The diesel engine is the most efficient device for converting chemical energy stored in liquid hydrocarbon fuels into useful work. Up to 50% of the energy in the fuel is converted into output shaft work. The modern diesel engine is twice as efficient as the early diesel engines and produces as much as sixty times as much power for a given cylinder size. These developments have, in recent years, been accompanied by a substantial reduction in the noxious elements in the exhaust gas so that engines are now, relatively speaking, ecologically clean. The developments have centred around exhaust gas turbocharging and improved fuel injection systems, but recent work on low-heat-rejection engines has resulted in significant advances in structural ceramics and in high-temperature lubricating oil, as well as an enhanced understanding of heat transfer in high-temperature combustion chambers. (author).

Energy Technology Data Exchange (ETDEWEB)

Researches and production of radio-isotopes, radio-pharmaceuticals and cold kits are carried out in the Radio-isotope Production Facility (RIPF). Four concrete hot cells in Bank-1 are to produce the Ir-192 source for NDT. Eleven lead hot cells in Bank-2 are to produce Ho-166, Cr-51, P-32/33, Tc-99m, Lu-177, Sr-90/Y-90 and W-188/Re-188 for research purpose. Six lead hot cells in Bank-3 are used for the production of I-131 for diagnosis and therapy of cancer in the hospital. A hot cell in Bank-3 is also utilized for the research of I-125 and Br-82. Four lead hot cells in Bank-4 are utilized for the production of Mo-99/Tc-99m generators since 2005. The major systems including the Heat and Ventilated Air Conditioning (HVAC) system and the air cleaning system such as charcoal and HEPA filter trains to filter the radioactive contaminants are in operation. So are the systems such as power ...

International Nuclear Information System (INIS)

One of the design targets for the ITER Tokamak Exhaust Processing system is not to lose more than 10"-"5 g h"-"1 into the Normal Vent Detritiation System of the Tritium Plant. The plasma exhaust gas, therefore, needs to be processed in a way that an overall tritium removal efficiency of about 10"8 is reached. Such a high decontamination factor can only be achieved by multistage processes. The third step of the three step CAPER process developed at the TLK is based on a so-called permeator catalyst (PERMCAT) reactor, a direct combination of a Pd/Ag permeation membrane and a catalyst bed. The PERMCAT principle is based on isotopic swamping in a counter current mode. Previous tritium experiments employing laboratory scale PERMCAT reactors have revealed decontamination factors as high as 10"5 for the third CAPER step. First tritium tests with a technical scale PERMCAT reactor led to similar decontamination factors and clearly ...

Energy Technology Data Exchange (ETDEWEB)

Availability of a natural gas-powered van that meets California`s ultra low emission vehicle requirements and has a 300-km range was reported. A similar van with an electric system giving a range of 240 km was also within sight. Regarding the limitations of electric batteries it was suggested that a super capacitor may allow systems to achieve higher energy densities; a refuelable zinc-air battery could be considered for vehicle use. While the prospect for emissions improvement of gasoline vehicles has clearly improved in recent years, the relative costs of infrastructure, vehicle and fuel for the the alternative fuels compared with gasoline demonstrate the difficulty the alternative fuels have in taking market share from gasoline. For the next decade, gasoline, propane and CNG are expected to be the dominant fuels for vehicles. After that, the leading fuel will be the one that has been most extensively researched and ...

Energy Technology Data Exchange (ETDEWEB)

As a part of the WE-NET project, the tanker for liquid hydrogen transport was studied. In fiscal 1996, some experiments and numerical analyses were proposed which are necessary to solve technological issues extracted in fiscal 1995 for heat insulation structure. The issue was roughly classified into vacuum and non-vacuum insulation, and their basic functions and required performance were arranged. Boil-off rate of 0.2-0.4%/d was targeted. The insulation system which applies polyurethane form (PUF) to tank surfaces and injects atmospheric N2 gas into the surrounding hold space, could achieve the targeted insulation performance by PUF of 1m in thickness. The system of vacuum panel insulation and atmospheric N2 gas injection into a hold space required the panel of 500mm in thickness because of the large effect of metallic outer panel material. The system of vacuum hold and PUF panels ...

Energy Technology Data Exchange (ETDEWEB)

In support of technology development to utilize coal for efficient, affordable, and environmentally clean power generation, the Power Systems Development Facility (PSDF) located in Wilsonville, Alabama, routinely demonstrates gasification technologies using various types of coals. The PSDF is an engineering scale demonstration of key features of advanced coal-fired power systems, including a KBR (formerly Kellogg Brown & Root) Transport Gasifier, a hot gas particulate control device, advanced syngas cleanup systems, and high-pressure solids handling systems. This report summarizes the results gasification operation with Illinois Basin bituminous coal in PSDF test campaign TC17. The test campaign was completed from October 25, 2004, to November 18, 2004. System startup and initial operation was accomplished with Powder River Basin (PRB) ...

Energy Technology Data Exchange (ETDEWEB)

A radioactive Waste Incineration System (WIS) with suspension combustion is noticed as effective volume reduction technology of low level radiactive wastes that are increasing every year. In order to demonstrate the decontamination efficiency of ceramic filter used on WIS, this test has been carried out with the test facilities as joint research of Central Research Institute of Electric Power Industry (CRIEPI) and Sumitomo Heavy Industries, Ltd. Miscellaneous combustible waste and power resin, to which 5 nuclides (Mn-54, Fe-59, Co-60, Zn-65, Cs-137) were added, were used as samples for incineration. As the result of the test, it was verified that Decontamination Factor (DF) of the single stage ceramic filter was usually kept over 10/sup 5/ for every nuclide, and from the results of above DF, over 10/sup 8/ is expected for real commercial plant as a total system. Therefore, it is realized that the off-gas ...

Science.gov (United States)

This book describes one approach to building and operating biogas systems. The biogas systems include raw material preparation, digesters, separate gas storage tanks, use of the gas to run engines, and the use of the sludge as fertilizer. Chapters included are: (1) "Introduction"; (2) "Biogas Systems are Small Factories"; (3) "The Raw Materials of Biogas Digestion"; (4) "The Daily Operation of a Biogas Factory"; (5) "The Once a Year Cleaning of the Digester"; (6) "Tanks and Pipes: Storing and Moving Biogas"; (7) "The Factory's Products: Biogas"; (8) "The Factory's Products: Biofertilizer"; (9) "The ABCs of Safety"; and (10) "Conclusion: Profiting from an Appropriate Technology." Many diagrams are provided throughout this handbook. New ideas, composting, bioinsecticides, ferrocement, facts and figures, sources and resources, feasibility studies, problem solving, ...

Energy Technology Data Exchange (ETDEWEB)

This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NOX, and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired plants. Global carbon dioxide emissions are lowered by 3% to 5%. Sulfur dioxide emissions ...

Energy Technology Data Exchange (ETDEWEB)

A new process for the removal of tar from biosyngas, OLGA (Oil and Gas Washer), is presented. This gas cleaning technology is based on physical principles and is designed to eliminate tar problems that relate to fouling and er pollution. The applied principles are confirmed by experimental validation. OLGA can be operated without suffering from harmful effects on important gasification characteristics as cold gas efficiency, gasifier simplicity, and feedstock flexibility. Some fundamental considerations in the development of OLGA are discussed. Amongst these is a different approach to the tar problem. This approach does not consider the total tar content as decisive in the evaluation of gas cleaning equipment. Instead, evaluation is focussed on whether tar properties as condensation behaviour and water solubility can still occur. A biosyngas free of tar should ...

International Nuclear Information System (INIS)

Total EU (and Norway) emissions of CO_2 from thermal power generation were some 950 million tonnes in 1990, the Kyoto agreement reference level. An ongoing research project, the GESTCO project, will provide the first documentation that, for the emission sources within the selected key areas, sufficient geological storage capacity is available for at least 30 years and possibly much longer. Cost of energy will obviously increase, but it is anticipated that electricity production cost price will be comparable to that of renewables. It would further have major implications for the European power generating industry which today is totally dominated by fossil fuel combustion with enormous emissions problems. The identification and siting of subsurface CO_2 storage capability can be expected to have considerable effect on the planning for and future siting of fossil fuel plants. In Norway there are plans to build several major, coastally sited, natural gas-fed ...

Energy Technology Data Exchange (ETDEWEB)

For IGCC, the primary investment is too high due to the demand of high gasification efficiency. For PFBCC, the thermal efficiency is too low due to the relatively low turbine inlet temperature and the hot working medium of the gas turbine is not easy to clean. A new scheme is proposed for coal fired combined cycle to overcome the main drawbacks of IGCC and PFBCC. The research targets are developing a new cycle construction of coal fired combined cycle to raise the efficiency and reduce the primary investment. Actually, the new scheme is a synthesis of some existing proposals. It adopts partial gasification to reduce the primary investment of the gasification equipment. The un-gasified surplus solid is then fed to a pressurized fluidized bed boiler, but adopting Curtiss Wright type external combustion to lower the ash content in the working medium. The gas fuel from the partial gasifier is combusted in a top combustor to ...

Energy Technology Data Exchange (ETDEWEB)

A method for cleaning timing optimization in a parallel steam generator system is described. The method is based on the minimization of a suitable objective function, and takes into account the load allocation on steam generators. In order to establish appropriate fouling growth models the mechanism of the particle deposition and removal on heat transfer surfaces is analyzed. The objective function is related to the short time management costs which are based on depreciation of steam generators, fuel costs and the costs of cleaning interventions. The optimization problem is described; a direct one level method is compared with a two level method. Some applications and their results are reported and discussed. (author)

Energy Technology Data Exchange (ETDEWEB)

A closed economic system was assumed for the Veneto Region (Italy) in order to define an appropriate input-output model and assess the future economic and environmental impacts of proposed actions for energy source development and economic growth. Present and forecasted energy demands (to the year 2000) were determined by energy source, e.g., natural gas, coal, petroleum and hydropower for the different consuming sectors - agriculture, transportation, industry, etc. Forecasts were made of the air pollution expected as a result of different types of energy and technology inputs for each sector. These considered planned retrofits towards clean combustion systems. Costs were estimated for the implementation of proposed pollution abatement measures, as well as, for the effects of energy use related environmental damage and measures to restore the environment. Some of the factors taken into account were: the ...

Energy Technology Data Exchange (ETDEWEB)

As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.

Science.gov (United States)

The paper discusses recent work on lime enhancement and testing at the bench-scale, followed by evaluation of the more promising sorbents in a pilot plant to develop low cost, retrofittable flue gas cleaning technology specifically the development of highly reactive sorbents. Con...

Energy Technology Data Exchange (ETDEWEB)

A highly effective and economical apparatus was developed by the All-Union Scientific Research Institute for Energy and Nonferrous Metallurgy for cleaning waste gases from cupola and electric arc steel melting furnaces --- the ''Ural'' rotoclone, which has been successfully introduced in many enterprises. Research results are presented for the efficiency of operation of these aggregates on equipping them on cupola and electric furnaces. With a 2 kPa aerodynamic resistance of the rotoclone the flue gas of the cupola furnace is cleaned to the sanitary standard. Highly effective collection of sublimates and aerosols from the electric arc furnace takes place with a ''Ural'' rotoclone aerodynamic resistance

Energy Technology Data Exchange (ETDEWEB)

This is the first time that the adsorption of binary mixtures of polycyclic aromatic hydrocarbons (PAHs) has been studied. This study was carried out at laboratory scale in an experimental apparatus specially designed for this aim: with gas-phase fluorescence, a new detection procedure was used. Experimental conditions, mainly in terms of temperature (150C) and contaminant concentration (approximately 1 ppmv), close to the ones observed in energy generation systems, were applied. The PAH adsorption process interpretation was carried out by recording the experimentally obtained breakthrough curves. After the detection parameter optimization, the influence of adsorbate characteristics in the hot gas cleaning of PAH was studied. In this system, the adsorption of 10 binary mixtures of five PAH (naphthalene (Np), fluorene (Fu), phenanthrene (Phe), fluoranthene (Fl), and pyrene (Py)) on ...

Energy Technology Data Exchange (ETDEWEB)

A publication on Norwegian gas and gas export. The content is wide spread from use of gas in daily life via sub sea pipeline repair systems to an overview over tomorrows gas fields. (AG)

Energy Technology Data Exchange (ETDEWEB)

The EMP consists of a Compliance Monitoring Sampling Program and a Supplemental monitoring Sampling Program. The Compliance Monitoring Sampling Program will be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Project and during a summer and a winter period following the successful Startup and Operational phase of the completed Project. compliance monitoring consist of conducting all the sampling and observation programs associated with existing required Federal, State, and Local Regulations, Permits and Orders. These include air, water, and waste monitoring and OSHA and NESHAP monitoring. The Supplemental Monitoring Program will also be conducted during a summer and a winter Baseline periods during the Pre-Construction/Construction phases of the Demonstration Facility and during a summer and a winter period following the successful startup and Operational phase of the completed Facility. Supplemental Monitoring includes ...

Energy Technology Data Exchange (ETDEWEB)

All of the project work since the previous report has been on Phase 2B tasks. Therefore, this quarterly progress report summarizes the period's activities in Engineering, Procurement and Civil Construction. Engineering is 95% complete, but revisions and changes are still being incorporated particularly in the Instrument and Electrical areas. Procurement has only valves 4 in. and above yet to order to complete all major items purchased. The scheduled material curve was based on the original estimate of the job. The projected curve reflects the previous month's estimate. Construction of civil work is proceeding according to schedule in the field. The initial bid packages for the Mechanical General Contractor portion of the work have been reviewed and evaluated. Order placement is scheduled for the end of July. The Electrical package is due back from the bidders on July 6. It requires additional evaluation by BSC and DSO and will not be placed until late August. The cost ...

Energy Technology Data Exchange (ETDEWEB)

Issues regarding the development of mechanisms to reduce greenhouse gas emissions in the electricity sector are discussed. Environmental groups have proposed mechanisms such as carbon taxes. Three other mechanisms have also been proposed under the Framework Convention on Climate Change (FCCC). These include the Clean Development Mechanism, Joint Implementation and carbon trading. A pilot emission reduction trading project began in Ontario in 1996 as an initiative to control smog and ozone in the southern provincial airshed. Substances of interest include NO{sub x}, volatile organic compounds (VOCs), SO{sub x}, carbon monoxide and other greenhouse gases. Ontario Hydro alone has conducted 10 trades, five with companies in the U.S., two of those for carbon emissions. An analysis of the pilot trade deals will provide an idea of the value of this mechanism. In addition to details of the trades, this article also addresses concerns regarding the ...

Energy Technology Data Exchange (ETDEWEB)

The production of and emission factors for the air-polluting matters sulfur dioxide, nitrogen oxides, carbon monoxide, hydrocarbons (esp. benz(a)pyrene), aldehyde and soot with regard to natural gas, excluding process furnaces, are dealt with. The comparison with other fuels indicates that only as to nitrogen oxides and carbon monoxide are emission factors equal in order of magnitude. As a summary measure of all air-polluting matters the emission index as proposed already in 1972 is applied. It shows emissions with single-room furnaces for heating oil EL to be six times as high as with natural gas; with black-coal briquettes the factor is at least 33, with wood chimneys about 200.

Science.gov (United States)

In this paper, a novel type of a corona discharge plasma reactor was designed, which consists of needle-plate-combined electrodes, in which a series of needle electrodes are placed in a glass container filled with flue gas, and a plate electrode is immersed in the water. Based on this model, the removal of NO and SO2 was tested experimentally. In addition, the effect of streamer polarity on the reduction of SO2 and NO was investigated in detail. The experimental results show that the corona wind formed between the high-voltage needle electrode and the water by corona discharge enhances the cleaning efficiency of the flue gas because of the presence of water, and the cleaning efficiency will increase with the increase of applied dc voltage within a definite range. The removal efficiency of SO2 up to 98%, and about 85% of NOx removal under suitable conditions is obtained in our experiments.

Energy Technology Data Exchange (ETDEWEB)

Naval Petroleum Reserve No. 3 (NPR-3), also known as Teapot Dome, is a government-owned oil field in Natrona County, Wyoming. It is an asymmetrical anticline located on the western edge of the Powder River Basin, just south of the Salt Creek Anticline. Production started in 1922, and today the field is a marginally economic stripper field with average production of less than 3 BOPD (0.5 m{sup 3}/D) per well. Total field production is about 1,800 BOPD (286 m{sup 3}/D). The Second Wall Creek Formation was waterflooded from 1979 until June 1992 with poor results due to the extensive natural fracture system in this sandstone unit. Since water injection ceased, reservoir pressure has declined to very low levels. Liquids extraction and reinjection of the gas produced from high-GOR wells along the gas-oil contact continues, but the average gas cap pressure has fallen to approximately 150 psi (1.03 MPa) from an ...

International Nuclear Information System (INIS)

Recycling of used battery for recovering lead done by either small household/small scale industries has been identified as a source of air pollution, especially by heavy metal (Pb). This condition give an adverse impact toward workers and societies. Technological aspect is one of the causal. The process apply an open system. Therefore, a lot of energy, as well as dust wasted to the air without prior treatment. For overcoming this condition, closed system by utilizing Cupola furnace will be offered as one of the alternatives clean technology application and to increase the recovering performance in order to set an effective and efficient result. (author)

Energy Technology Data Exchange (ETDEWEB)

The dry desulfurization, denitrification and air toxics removal process using activated coke (AC) has been commercially adapted for flue gas clean up of a power plant, an oil refinery plant, an iron ore sintering plant, and a refuse incinerator. This process can achieve 100% removal of SO{sub x}, over 80% removal of NO{sub x} and effective removal of air toxics such as Hg, HCL, dioxines, etc., by contacting flue gas with AC and injecting NH{sub 3} for DeNO{sub x} at temperature range of about 100-200{degrees}C. For flue gas treatment, AC has several functions, which basically depends on the chemical surface group on AC inner surface. As adsorbent, AC can adsorb SO{sub x} at the relatively basic oxygen group site, where the adsorbed SO{sub x} is stored as sulfuric acid into micropore structure of AC. As catalyst, AC can decompose NO{sub x} catalytically with addition of NH{sub 3}. The catalytic activity ...

Wastenet

... IN-STORE PROCUREMENT SERVICES - Energy (Electric/Gas) - Telecoms (Call/Lines/Switchboards/Mobiles) - Waste & waste compliance (Cleaning/Collection/Compliance) - Carrier bags (Plastic/Paper) - Stationery (Supplies) - Catering (Consumables/Equipment) - Insurance (Business/Legal/Personal) - Water (Rates/Coolers) - Personnel (Staff Uniforms/Recruitment/Training) - Security (Patrols/Surveillance Equipment) - Instore ...

Energy Technology Data Exchange (ETDEWEB)

With the development of the latent heat store and its inclusion in the conventional heating control of cars, success has been achieved both in increasing comfort and in making an important contribution to safety of driving. Great store is set in development of the system on its environmental friendliness, for example by the thorough use of environmentally friendly and reusable materials. This also means the use of clean materials. It was shown that the latent heat store (apart from the aspects of comfort and safety of driving) can also make a contribution to saving fuel and reducing the exhaust gas. The sum total of the advantages makes it clear that the latent heat store introduced here is a very environmentally friendly system with multi-functional properties. (orig.) [Deutsch] Mit der Entwicklung des Latentwaermespeichers und seiner Einbindung in die konventionelle Heizungsregelung von Automobilen ...

Energy Technology Data Exchange (ETDEWEB)

The report presents the results of a Gas Research Institute (GRI) program to evaluate the technical and economic aspects of design options proposed by the U.S. Department of Energy (DOE) for reducing the energy consumption of residential ranges and ovens as mandated by the National Appliance Energy Conservation Act (NAECA) of 1987. The study shows that none of the proposed DOE design options are justified except electric ignition for stand-alone cooktops, based on life-cycle costs, loss of consumer utility, safety, technical considerations, or food quality considerations. An individual range uses so little gas during the year (approximately $14/year for a self-cleaning range) that it is difficult to justify any design modification, since the cost of even a simple modification could not be recovered on the basis of gas saved.

International Nuclear Information System (INIS)

A high-average power (kW) infrared (IR) free-electron laser (FEL) is currently being commissioned for the Jefferson Laboratory FEL User Facility. The IR FEL is driven by a unique superconducting rf linac which is recirculated to recover electron beam power that is not radiated in the FEL. The design and installation of the vacuum system for the FEL involved particular attention to minimizing particulate contamination which could cause problems with the superconducting acceleration cavities and the high power FEL optics. Particulate contamination levels of all vacuum components were monitored during the cleaning process using laser scattering. Cleaning, transport, and installation procedures were developed to minimize the contamination of the complete system. We will summarize a data base we compiled of particulate contamination levels of the various components installed in the FEL vacuum ...

Energy Technology Data Exchange (ETDEWEB)

The paper discusses clean coal technology developments in India. 2 photos.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Conversion of coal gas into liquid products is a multistep process which involves numerous unit processes. Compared with similar processes using natural gas as feedstock, there are challenges, particularly with the gas purification. There are, however, also advantages when using a carbon-monoxide-rich gas which ultimately may result in a greatly simplified process. This paper discusses the challenges when converting a gas from an entrained coal gasifier into a liquid product and the paper presents the various options available. The following issues will be touched upon: sour gas shift and adjustment of the H{sub 2}/CO ratio; acid Gas Removal (AGR) - when and how; syngas purification; methanol and combined methanol/DME synthesis; gasoline synthesis; future integrated processes. Here, various options are available depending on the gasifier; ...

Science.gov (United States)

... Accession Number : ADD135818. Title : Performance of Titanium in Flue Gas Desulfurization Scrubber Systems,. Descriptive Note : Journal Article,. ...

Science.gov (United States)

This report gives the results of a survey of operational flue gas desulfurization (FGD) systems on coal-fired utility boilers in the United States. The FGD systems installed on Units 1 and 2 at the Bruce Mansfield Station of the Pennsylvania Power Company...

International Nuclear Information System (INIS)

Two different reverse osmosis systems were investigated. The first was a 50-element plant-scale system that is used to treat 2200 m"3 of AECL liquid radwastes annually.It uses thin-film composite (TFC) membranes and operates at an applied pressure of 2760 kPa, with a fixed crossflow of about 40 L/min. The other system uses the same thin-film composite membranes for waste processing but is a two-element pilot-scale system. It is operated at pressures m ranging between 1500 and 7000 kPa, at a fixed crossflow of 55 L/min. The average lifetime of the thin-film composite membranes in the plant-scale processing application at AECL is about 3000 h. After this service life has expired the rejection efficiency declines rapidly from 99.5% to about 95% as the membranes become impaired from chemical cleaning procedures that are required after each 100 m"3 of waste is treated. The permeation ...

Science.gov (United States)

This report--the forty-fifth of a series--is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion process development, materials engineering, alkali metal vapor topping cycles, a coal equipment test program, an AFB coal combustor for cogeneration (CCC), engineering and support studies, process and program assistance, evironmental assessment studies, magnetic beneficiation, and AFBC demonstration plant.

Energy Technology Data Exchange (ETDEWEB)

A 100 kW thermal input Two-Stage Gasifier was built at the University of Denmark (DTU). The gasifier consists of an externally heated pyrolysis unit, a down-draft char gasifier, a gas cleaning system and an internal-combustion engine. Between the summer of 1996 and the summer of 1998, 11 tests were made with the gasifier. The gasifier had a total operating time of 278 hours (excluding warming up). The fuel was mainly wood chips, but also briquettes has been used. Four of the tests lasted 50-70 hours, and stable conditions were reached. All the tests were completed without technical problems. The particle sizes and amounts were investigated. The amount of particles depended on the amount of steam led to the gasifier. More than 99% of the particles after the cyclone were soot. The size of the soot particles was mainly between 0.2-0.5 {mu}m. Under normal conditions (biomass:steam = 1:1 (dry mass basis)), the particle load was ...

Energy Technology Data Exchange (ETDEWEB)

The productivity characteristics of perforated gas well are investigated for the first time under real conditions considering drilling damage, perforation compacted zone and anisotropy in this paper. A non-linear finite element model for non-Darcy flow in perforated gas reservoir is built to consider the effects of twelve factors on productivity ratio (PR) of perforated gas well. The nomographs for two cases are presented in this paper. Compared with previous works, the following results are found: (1) the effects of drilling damage and perforation diameter on PR of gas well are more remarkable than that in oil well; (2) any perforation phase may be the best or the worst as to perforating gas well, which depends on anisotropy, drawdown and that whether or not perforations are beyond drilling damage zone; (3) the increase in perforation length hardly improve PR of ...

International Nuclear Information System (INIS)

The performance of the gas-jet transport system coupled to the RIKEN gas-filled recoil ion separator GARIS was investigated using 255No produced in the 238U(22Ne, 5n)255No reaction. Alpha particles of 255No separated with GARIS and transported by the gas-jet system were measured with a rotating wheel apparatus for ? spectrometry under low background condition. The high gas-jet efficiencies of about 75% were independent of the recoil ranges of 255No in the gas-jet chamber. The present results suggest that the GARIS/gas-jet system is a promising tool for the next-generation superheavy element chemistry: (1) the background radioactivities of unwanted reaction products are strongly suppressed, (2) the intense beam is absent in the gas-jet chamber and hence the high ...

Science.gov (United States)

The report, generated by a computerized data base system, presents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems, operational domestic particle scrubbers, and Japanese coal-fired utility FGD installations. It ...

Science.gov (United States)

The report discusses the capabilities of equipment vendors to supply and install the quantity of flue gas desulfurization systems required to meet alternative standards for coal-fired steam generators. It analyzes limiting factors affecting supply capabilities (such as the availa...

Energy Technology Data Exchange (ETDEWEB)

In this book are found technical and scientific papers on the main works of the Direction of the Fuel Cycle (DCC) in France. The study fields are: the up-side of the nuclear fuel cycle with theoretical studies (plasma simulation) and technological developments and instrumentation (lasers diodes, carbides plasma projection, carbon 13 enrichment); the down-side nuclear fuel cycle with theoretical studies (ion Eu{sup 3+} complexation simulation, decay simulation, uranium and plutonium diffusion study, electrolyser operating simulation), scenario studies ( recycling, wastes management), experimental studies; dismantling and cleaning (soils cleaning, surface-active agent for decontamination, fault tree analysis); analysis with expert systems and mass spectrometry. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

Vietnam is beginning its industrialization process, and it currently lacks the capital necessary for expensive pollution control and treatment systems. Pollution strategies are critical for the country. This study evaluates the present status of industry and the pollution problems associated with industrial development in Vietnam. The purpose of the study is to identify sectors that may have potential for promoting cleaner production practices. 4 refs.

Energy Technology Data Exchange (ETDEWEB)

Electric cars are a clean and noiseless alternative to vehicles with combustion engines for journeys in cities and their environs. In recognition of this, ABB has developed an efficient electric drive system featuring modern power electronics and a high-energy, sodium-sulphur battery. The energy-to-weight ratio of this battery is four times that achieved with conventional lead-acid batteries. To recharge the battery, a charger mounted next to the motor has only to be connected to a household power socket.

Energy Technology Data Exchange (ETDEWEB)

Space HVAC systems are to provide hygienical room air. Air change is necessary because of pollutants released from materials or production processes but also because of the presence of humans or animals who consume oxygen. Poor room climate and/or poor air hygiene do not only reduce the felt comfort but may also result in a loss or profitability and higher sickness rates. (orig.)

Science.gov (United States)

... 5. The results of the bond strength measurements were compared to the surface cleanness of the aged EPDM as determined by the specified ...

Energy Technology Data Exchange (ETDEWEB)

In developing countries with rapidly growing economies, energy consumption will more than triple by 2030. This will require more than 8 trillion euros in investments in energy in these countries. The way these investments are made will be crucial in determining whether greenhouse gas emissions will rise proportionately. By creating a worldwide, lucrative market for clean technologies, countries can use the money they set aside for fighting climate change to stimulate large-scale private investment in clean energy production and efficient energy consumption. A well-functioning market ensures that money is invested where it will be the most cost-effective and will have the greatest impact in helping to solve a generally recognised problem. This also means making sure that innovations get to the market, so as to take advantage of economies of scale. The conference on 16 and 17 October 2006 in Amsterdam was the official start ...

Science.gov (United States)

The 575-mile Statpipe gas transportation system entails 191 miles of wet-gas line running from the Statfjord field across the Norwegian trench to the Karsto, Norway, conditioning plant and 384 miles of dry-gas line from Karsto, again across the trench, to the Heindal and Sleipner fields for final connection at Ekofisk with the Norpipe system for transport to Emden, West Germany. Special construction considerations include the 1000-ft-deep trench crossings, the rocky shore approach and departure, and the subsea tie-ins required at depths of up to 500 ft. The system has an initial annual design capacity of 186 billion CF of wet gas and 260 billion CF through the dry-gas line to Emden.

Energy Technology Data Exchange (ETDEWEB)

The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through September 1999.

International Nuclear Information System (INIS)

Details of a 1 day conference designed to create more efficient interactions between the gas supply and electricity systems in Ontario and new models for gas supply and the electricity system were presented. Market efficiency, generators' perspectives on critical gas issues, an overview of the North American gas and an outline of issues concerning Ontario were discussed. A natural gas industry forecast and issues concerning marketers and producers were presented. The terms on which gas is bought and sold were discussed. Regulatory tools, cost allocation and issues relating to unbundling were also presented. Infrastructure needs were reviewed, as well as basic market structures. It was suggested that appropriate commercial service options need to be developed and approved, including cross-utility services.

Energy Technology Data Exchange (ETDEWEB)

Experimental data on the gas holdup and the mean bubble size in a bubble column with a single nozzle was obtained for gas-molten salt systems of a eutectic mixture of LiCl (58 mol %)-KCl (42 mol %) and molten NaNO/sub 3/. The liquid-phase mass transfer coefficient K /SUB L/ was evaluated from the specific surface area a and the volumetric coefficient K /SUB L/ a data for oxygen and carbon dioxide absorption into molten NaNO/sub 3/. The dimensionless correlations of the performance of bubble columns for aqueous solutions can be extended to the gas-molten salt systems.

International Nuclear Information System (INIS)

Object: To minimize the range of the liquid level variation of the cooling system and reduce the time required for the liquid level control by sealing the gas of a cover gas respiration system which acts upon an evaporator and pump overflow column. Structure: In liquid level control by the cover gas pressure of a high-speed reactor secondary cooling system, upon occurrence of a sudden change in the rate of flow of the recirculated liquid, automatic check valves provided in an evaporator and pump overflow column cover gas respiration system are completely or substantially closed, while at the same time the recirculation cooling medium is sucked up and an automatic check valve provided in the overflow system is closed. (Kamimura, M.).

Energy Technology Data Exchange (ETDEWEB)

Ventilation systems must ensure high room air quality with minimum energy consumption in all states of operation. Systems for ventilation on demand are increasing their market share. (orig./MSK) [Deutsch] Oberste Aufgabe von Raumlufttechnischen Anlagen ist die Sicherstellung guter Raumluftqualitaet bei minimalem Energieverbrauch unter allen Betriebsbedingungen. Um dieses Ziel zu erreichen, setzt sich am Markt zunehmend die bedarfsgeregelte Lueftung durch. (orig./MSK)

Energy Technology Data Exchange (ETDEWEB)

Requirements are provided for NSLS beam line front ends and vacuum interlocks. Guidelines are provided for UHV beam line vacuum systems, including materials, vacuum hardware (pumps, valves, and flanges), acoustic delay lines and beam line fast valves, instrumentation, fabrication and testing, and the NSLS cleaning facility. Also discussed are the design review for experimenters' equipment that would be connected to the NSLS and acceptance tests for any beam line to be connected with the ring vacuum. Also appended are a description of the acoustic delay line as well as the NSLS vacuum standards and NSLS procedures. (LEW)

Energy Technology Data Exchange (ETDEWEB)

The present research has been made to develop and review critically the functional requirements of the specific safety systems of CANDU such as SDS-1, SDS2, ECCS, and containment. Based on R documents for this, a systematic study was made to develop the domestic regulation statements. Also, the conventional laws are carefully reviewed to see the compatibility to CANDU. Also, the safety assessment method for CANDU was studied by reviewing C documents and recommendation of IAEA. Through the present works, the vague policy in the CANDU safety regulation is cleaning up in a systematic form and a new frame to measure the objective risk of nuclear power plants was developed.

Energy Technology Data Exchange (ETDEWEB)

The Externally-Fired Combined Cycle (EFCC) offers a method for operating high-efficiency gas and steam turbine combined cycles on coal. In the EFCC, an air heater replaces the gas turbine combustor so that the turbine can be indirectly fired. Ceramic materials are required for the heat exchange surfaces to accommodate the operating temperatures of modern gas turbines. The ceramic air heater or heat exchanger is the focus of this program, and the two primary objectives are (1) to demonstrate that a ceramic air heater can be reliably pressurized to a level of 225 psia (1.5 MPa); and (2) to show that the air heater can withstand exposure to the products of coal combustion at elevated temperatures. By replacing the gas turbine combustor with a ceramic air heater, the cycle can use coal or other ash-bearing fuels. Numerous programs have attempted to fuel high efficiency gas turbines ...

Energy Technology Data Exchange (ETDEWEB)

The systems analyses and optimization studies performed in connection with a program to design and evaluate a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion and advanced technology in the hot gas cleanup system and gas turbines are presented. Details on the plant control system are included. (LCL)

Energy Technology Data Exchange (ETDEWEB)

This report describes the combustion experiments performed using the SP Industry Calorimeter. In addition to measuring parameters such as heat release rate (HRR), mass loss rate, effective heat of combustion and smoke obscuration, considerable effort was put into the characterisation of the smoke gases in order to obtain a basis for evaluations of the toxic potency of the smoke. The materials studied were Nylon 66, polypropene, polystyrene (with and without fire retardant, respectively), PVC and chlorobenzene. A total of 19 large-scale, well ventilated combustions were carried out. The mass of sample burned ranged from 20 kg to 125 kg in an experiment. A procedure was designed for cleaning the smoke gas duct between experiments and was found to be effective. Measurements were carried out for the amounts of O{sub 2}, CO{sub 2}, CO, NO{sub x}, THC (unburned hydrocarbons), HCN, HCl, NH{sub 3} and individual organic compounds in the smoke. ...

Science.gov (United States)

The paper is an overview of utility flue gas desulfurization (FGD) technology and costs. The two commercially offered throwaway and salable product systems that are considered to be the most important for near-term (through 1990) SO2 control are: throwawa...

Energy Technology Data Exchange (ETDEWEB)

Gas turbine component protection remains essential but environmental regulations emphasize the gas-turbine efficiency. Heating and cooling are features often integrated into the GI air intake packages to provide the optimum operating conditions. This paper describes modern inlet air treatment systems and discusses their effectiveness. (author)

International Nuclear Information System (INIS)

Full text: Chemical-technology approaches allowing to intensification the prevention processes of gas hydrates formation at motion of gas-liquid stream of natural gas in system natural gas well - gas wire have been worked up. Technological regimes of treatment of gas stream have been determined. Linear correlation dependences inhibitor electrolytes contained hydrated ions with different ion radii and charges of subgroups of alkali elements with one - type electron configuration were obtained. Important physico-chemical parameters of electrolytes have been determined: activity; coefficients of activity, viscosity, diffusion; density; heat capacity; heat conductivity; surface tension and freezing-point. The features of continuous influence of inhibitory factors on process of gas flow at low temperatures and relatively high ...

Science.gov (United States)

Prepared to make housing project managers, maintenance engineering staff, and designers and architects of HUD - assisted and HUD - insured housing projects and mobile home parks aware of their responsibilities under the Natural Gas Pipeline Safety Act, this handbook provides technical guidance for the reduction of gas leaks and the handling of gas leak incidents in residential areas. The hazards of natural gas, concern over gas safety in residential areas, applicable codes and standards, and sources of information and help are reviewed, along with maintenance and engineering considerations relating to gas pipe failures, the detection of gas leaks, appliance servicing, and pipe installation, repair, and replacement. Housing management considerations are also examined, with attention to recordkeeping and reporting, emergency contingency ...

Science.gov (United States)

We present a new approach for growing Si nanowires directly from a silicon substrate, without the use of a metal catalyst, silicon vapor or CVD gasses. The growth can be performed in a furnace type configuration at moderate temperatures or in localized regions by resistive heating. Since the silicon wires grow directly from the silicon substrate, they do not need to be manipulated nor aligned for subsequent applications. Wires in the 20-50 nm diameter range with lengths over 80 ?m can be grown by this technique. We have studied the effects of various growth parameters, including temperature, substrate orientation, initial sample cleaning and carrier gasses. Results indicate that most important parameters in the growth of the nanowires are the surface cleaning, the temperature and the type of carrier gas used. A model is proposed, which involves an oxide catalyst for the process, with the growth of the nanowires enabled by a ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the safety gas management system utilizing public telephone cables. Buyo Gas Co., Ltd. has installed about 100 governors for exclusive-use or use in the districts to control the gas supply to the consumers. A gas safety management system has been developed. This system consists of a pressure sensor, the terminals of gas leak alarms, and their masters. The features lie in that the system can utilize public cables, is operative at interruption of power service, can correspond to emergency situations, serves to save the cost, and can display the data constantly. For electric facilities in a governor room and the NTT cable service work, sufficient agreement with the possessor is required. In the case of non-utility electric facilities, some restrictions are imposed on the cable work ...

Energy Technology Data Exchange (ETDEWEB)

Many Department of Energy facilities across the United States are seriously contaminated with radioactive and other hazardous wastes. Decades of focus on weapons production and inadequate attention to long-term solutions for dealing with those wastes have resulted in tremendous problems. The Department of Energy recognizes the seriousness of those problems and is addressing them. In some cases existing management systems are being used to accomplish the new mission of environmental cleanup, and in other cases new systems have been created to help carry out that mission. Widespread criticism of those efforts to data are evidence that the management systems being used may not be appropriate for the job. In particular, it appears that some management systems aren`t producing desired results because they are not well aligned with the people and tasks for whom they are intended, and these issues are ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a liquid-metal-cooled test reactor located on the Hanford site. A dual computer system has been developed to monitor the reactor cover gas to detect and characterize any fuel or test pin fission gas releases. The system acquires gamma spectra data, identifies isotopes, calculates specific isotope and overall cover gas activity, presents control room alarms and displays, and records and prints data and analysis reports. The fission gas monitor system makes extensive use of commercially available hardware and software, providing a reliable and easily maintained system. The design provides extensive automation of previous manual operations, reducing the need for operator training and minimizing the potential for operator error. The dual nature of the system allows ...

British Library Electronic Table of Contents (United Kingdom)

Fragranced consumer products are pervasive in society. Relatively little is known about the composition of these products, due to lack of prior study, complexity of formulations, and limitations and protections on ingredient disclosure in the U.S. We investigated volatile organic compounds (VOCs) emitted from 25 common fragranced consumer products-laundry products, personal care products, cleaning supplies, and air fresheners-using headspace analysis with gas chromatography/mass spectrometry (GC/MS). Our analysis found 133 different VOCs emitted from the 25 products, with an average of 17 VOCs per product. Of these 133 VOCs, 24 are classified as toxic or hazardous under U.S. federal laws, and each product emitted at least one of these compounds. For ''green'' products, emissions of these c...

International Nuclear Information System (INIS)

Discussions regarding the use of wood fuels for commercial energy production in the Netherlands began in the 1990's. The main reasons for using wood fuel are: the political demand for using renewable energy, the need to reduce CO_2 emissions, and the lack of markets for surplus timber. Only 10 % of the area of Holland is forested. Therefore, early thinning and cleaning are important management tools for improving growth and producing better quality timber. The energy potential from early thinning and plantation cleaning could be between 400 000 and 570 000 dry tons annually. The Netherlands has not experience in harvesting energy wood. However, through the International Energy Agency/Bioenergy Agreement, knowledge gained in other countries, especially Denmark, Sweden and Finland, is being transferred to Holland. In 1996, there have been made field tests with Danish equipment. Although there are few technical barriers to wood fuel in the ...

International Nuclear Information System (INIS)

In this paper it will be discussed how to most effectively give room to competitive forces in natural gas markets, given the traditional merchant pipeline as point of departure. Alternative models of organizing the market will be reviewed: we first consider decreasing barriers to entry and then analyse advantages and drawbacks of a third party access system. In this context different forms of implementing a competitive market for transportation capacity and coordinating it with gas trade are discussed, among them a simultaneous auction of gas and transmission capacity. Finally a hub system of point markets will be suggested to improve the currently implemented third party access system and to allow for competitive markets for gas and transportation service. 33 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

As concern regarding global environmental problems such as the greenhouse effect and acid rain has increased, so too has the demand for commercially viable solar cells as a clean energy source. Interest in amorphous silicon (a-Si) solar cells has been particularly high, due to their low cost. Technological developments in the field of a-Si solar cells are discussed from the viewpoints of fabrication process, materials, and cell structures. Various applications and systems that take advantage of the a-Si solar cell are then introduced. Finally, future prospects are mentioned

Energy Technology Data Exchange (ETDEWEB)

Constantly increasing resource efficiency together with the broad introduction of CCS technologies is fundamental for a continuous use of fossil fuels in power generation against the background of up-coming requirements for CO2 emission reduction. In principle, CCS means up-grading conventional power plant technology with proven CO2 removal processes. However, this leads to additional losses, auxiliary power demand and cost. System integration, development or at least adaption of components and processes are the main requirements in this context. Different technology solutions and recent developments will be addressed as well as challenges when implementing in demonstration projects.

Science.gov (United States)

Clean Water Act You are here: Water Laws & Regulations Policy & Guidance Clean Water Act Water Quality and 401 Certification Water Quality and 401 Certification Water Quality...

Science.gov (United States)

The report gives results of a second survey of the flue gas desulfurization (FGD) system on Unit 1 of Kansas City Power and Light Co.'s La Cygne Station. The FGD system, first started up in February 1973 and commercially available in June 1973, uses a lim...

Science.gov (United States)

The report gives results of a survey of the flue gas desulfurization (FGD) systems at Kansas Power and Light Co.'s Lawrence Power Station. The systems utilize boiler injection of pulverized limestone, followed by tail-end wet scrubbing: unit 4, with a net...

Energy Technology Data Exchange (ETDEWEB)

During cleanup of contaminated sites, Sandia National Laboratories, New Mexico (SNL/NM) frequently encounters soils with low-level radioactive contamination. The contamination is not uniformly distributed, but occurs within areas of clean soil. Because it is difficult to characterize heterogeneously contaminated soils in detail and to excavate such soils precisely using heavy equipment, it is common for large quantities of uncontaminated soil to be removed during excavation of contaminated sites. This practice results in the commingling and disposal of clean and contaminated material as low-level waste (LLW), or possibly low-level mixed waste (LLMW). Until recently, volume reduction of radioactively contaminated soil depended on manual screening and analysis of samples, which is a costly and impractical approach and does not uphold As Low As Reasonably Achievable (ALARA) principles. To reduce the amount of LLW and LLMW generated during the ...

Science.gov (United States)

Purge water from a typical wet flue gas desulfurization system contains myriad chemical constituents and heavy metals whose mixture is determined by the fuel source and combustion products as well as the stack gas treatment process. A well-designed water treatment system can tolerate upstream fuel and sorbent arranged in just the right order to produce wastewater acceptable for discharge. This article presents state-of-the-art technologies for treating the waste water that is generated by wet FGD systems. 11 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

The article focusses on operational experience gained with the following items: scrubbing system with oxidation, regenerative gas preheater, blower/fan, aerosol filter, and product processing. (orig./PW).

International Nuclear Information System (INIS)

Radiological and environmental protection experience associated with the reactor cover gas processing system at the Fast Flux Test Facility (FFTF) has been excellent. Personnel radiation exposures received from operating and maintaining the reactor cover gas processing system have been very low, the system has remained free of radioactive particulate contamination through the first seven operating cycles (cesium contamination was detected at the end of Cycle 8A), and releases of radioactivity to the environment have been very low, well below environmental standards. This report discusses these three aspects of fast reactor cover gas purification over the first eight operating cycles of the FFTF (a duration of a little more than four years, from April 1982 through July 1986).

Science.gov (United States)

Reactor Effluent Purification System. 7.4.3. Filter Reactor Outlet Gas (FROG). 7.5. Instrumentation and Controls for NSS Tests ...

Science.gov (United States)

... On 20 March 1995, members from the religious cult Aum Shinrikyo released sarin and VX nerve gas into the Tokyo subway system. At the height of ...

Energy Technology Data Exchange (ETDEWEB)

The risk perception of the public consists of two components: the objectively factual component and the subjectively irrational component. The two strategies adopted by the German gas supply industry are the internal and the external communication strategy. Concepts and measures of accident precaution, registration and analysis of accident data (installation and operating errors, defects on flue systems, pipelines and valves, subsequent installation of gas appliances) are discussed. (R.P.)

Science.gov (United States)

Bechtel Power Corporation has performed an evaluation of flue gas desulfurization (FGD) system cost versus design level of operating availability for an industrial sized dual-alkali process. Two principle sources were used: the Flue Gas Desulfurization Information System (FGDIS) maintained by the Environmental Protection Agency and budget quotations from an FGD vendor. A survey of the FGDIS data base proved inconclusive in establishing a relationship between FGD system cost and operating availability. Using equipment failure rates derived from various sources, component availability factors were developed for all major FGD system components. Cost and availability data of nine industrial FGD system configurations were analyzed on a per boiler basis. Linear curve fitting of these data produced mathematical relationships of cost and ...

Science.gov (United States)

Solid fuels such as coal, wood, and crop straw supply some fraction of household cooking and heating fuel for more than one billion people in China. As these fuels do not generally combust cleanly in household stoves, their use levies large health and environmental burdens, particularly in rural regions. Production of clean-burning fuels from agricultural residue offers one prospect for mitigating health and social burdens imposed by household use of solid fuels. This dissertation explores the question: how might production of clean-burning household fuels from agricultural residues affect human health and social conditions in rural China? I approach this question from three perspectives. First, a technically plausible but currently unproven village-scale energy technology is explored in a scenario bounded by natural resources and substantiated by engineering specifications, estimates of indoor exposures to air pollution, ...

Energy Technology Data Exchange (ETDEWEB)

The externally fired combined cycle (EFCC) process utilises a high temperature heat exchanger to transfer the heat of a dirty flue gas to a clean working medium. In comparison to other combined cycle concepts, like integrated gasification combined cycle or pressurized pulverized coal combustion, the problems of hot gas cleaning are avoided. The first part of the publication (BWK 5/02) deals with the possible concepts and the efficiency potential of the externally fired combined cycle. The applicability of metallic and ceramic heat exchanger materials are discussed. The second part summarizes the state of the art and presents the basic design of a ceramic heat exchanger. [German] Der extern gefeuerte Gasturbinenprozess arbeitet mit einem Waermeuebertrager, um ein Arbeitsmedium auf Gasturbineneintrittstemperatur zu erhitzen. Im Vergleich zu Kombiprozessen mit integrierter Kohlevergasung oder ...

British Library Electronic Table of Contents (United Kingdom)

Natural gas is a promising alternative fuel to meet strict engine emission regulations in many countries. Natural gas engines can operate at lean burn and stoichiometric conditions with different combustion and emission characteristics. In this paper, the operating envelope, fuel economy, emissions, cycle-to-cycle variations in indicated mean effective pressure and strategies to achieve stable combustion of lean burn natural gas engines are highlighted. Stoichiometric natural gas engines are briefly reviewed. To keep the output power and torque of natural gas engines comparable to those of their gasoline or Diesel counterparts, high boost pressure should be used. High activity catalyst for methane oxidation and lean deNOx system or three way catalyst with precise air-fuel ratio control str...

Energy Technology Data Exchange (ETDEWEB)

The majority of Brazilian big cities served by conventional railroad systems with routes starting in the center of the URBIS, destinate them the long distances transport of passengers and cargo. Actually, these systems are being transformed to become commuter trains which join a great capacity of transportation to a much lower costs of implantation than subway ones. The most important characteristic of this train, when talking about energy consumption, is the possibility of using different kinds of explosion engines from three cycles: Diesel, mixed (Diesel + Natural Gas), and Otto moved by natural gas, besides the traditional electric traction. The use of natural gas in Otto cycle engines shows itself competitive from the point of view of investments, operational costs and environmental preservation. (author). 10 refs., 1 fig

Energy Technology Data Exchange (ETDEWEB)

TSS (thermal swing sublimation) method was studied which uses vaporization heat and sensible heat of LNG for solidification and separation of CO2 gas in waste gases of LNG-fired combined cycle power generation system. In experiment, the mixed gas composed of CO2, H2O and N2 was used for simulating waste gas of LNG-fired combined cycle power generation systems, and the growth behavior of ice and dry ice was studied for developing dry ice making technology under low-temperature condition. As the experimental result, the following were clarified: various crystal structures depending on cooling temperature, the effect of gas flow rate on peeling of surface precipitated solids, and solidification characteristics of H2O/CO2 mixed gas. The growth rate of precipitated solid film thickness decreased with an increase in gas flow ...

International Nuclear Information System (INIS)

Tarapur Atomic Power Station Unit-4 is first 540 MWe pressurized heavy water reactor in India. It achieved criticality on 06th March 2005 and then operated at full power i.e 500 MWe. Radiation workers during the normal operation and reactor shutdown are exposed to radiation field. The control of dose rates and the collective dose of the radiation workers is most important for the best performance of the reactor. Experience gained during the operation of the 220 MWe reactors has shown that the Moderator system, primary heat transport system, annulus gas system and moderator cover gas system are the main systems contributing to the dose rate and collective dose. In order to identify the radio nuclides contributing to the radiation field, study was undertaken at TAPS Unit-4. Various samples from the Moderator, primary heat transport ...

International Nuclear Information System (INIS)

Measurements of the Kapitza conductance to liquid helium II across the (100) surface of single crystals of copper are presented. The temperature range of these measurements was 1.6-- 2.1 K. The sample surfaces were subjected to several different treatments. Some surfaces were cleaned by low-energy argon ion bombardment, annealed in an ultrahigh-vacuum system, and preserved under vacuum until purified liquid helium was admitted. Other surfaces were intentionally damaged by machining and/or exposure to the atmosphere. The conductance after these latter treatments was found to be about a factor of three higher than that of the more ideally cleaned and annealed surfaces, and a significant difference in the temperature dependence of the conductance was also observed. Conductances were reproducible for similarly treated surfaces and correlated with surface damage determined by x-ray diffraction. The relationship of these results ...

International Nuclear Information System (INIS)

The purpose of this work was to develop and evaluate a method of locating breached fuel within the Fast Flux Test Facility (FFTF) reactor based on the relative response of the delayed neutron monitors (DNM) located on each of the three primary sodium cooling loops. The primary method of location is the use of tag gas containing unique ratios of the noble gases xenon and krypton. Although the tag gas system works quite well, it is relatively expensive because of the costs of preparing and loading the gas into each fuel pin. Triangulation of DNM signals could potentially decrease tag gas costs while maintaining overall location reliability.

International Nuclear Information System (INIS)

Nova Corporation and its related businesses are involved in natural gas production, gas pipelines, consulting services, and upgrading of natural gas into chemicals and plastics. Nova owns Alberta Gas Transmission Division, the primary gas transportation system in Alberta, with 11,400 miles of pipeline and total deliveries in 1992 of 3.4 trillion ft"3. Nova also owns 50% of Foothills Pipe Lines Ltd., one of Canada's largest carriers of exported gas, and 50% of TQM Pipeline Partnership, which transports natural gas in Quebec. Nova conducts its chemicals business through Novacor Chemicals Ltd., which has plants in Alberta, Ontario, Quebec, and the USA. Novacor's major petrochemicals are methanol, ethylene, propylene, and styrene and its major plastics are polystyrene, polypropylene, and polyethylene. Nova's ...

Energy Technology Data Exchange (ETDEWEB)

A dust extraction system removes the contaminated air at source by means of a hood. The extraction system for dust is essentially a ducted air system that prevents excessive employee exposure to dust in the working zone. The four major mechanisms that remove the contaminants in an extraction system are: - capture of contaminants by hoods - transport of contaminated air in duct network - separation of dust in the collector - exhaust of clean air through stack. The current methods of design are based on empirical relations, multi-variable tables, graphs and nomographs that have been derived from the principle of fluid mechanics and particle dynamics. However, the empirical formulae, tables and graphs are used in different geographical locations of the world having different environmental conditions and geo-characteristics of dust particles. Therefore, it is required to establish a ...

Energy Technology Data Exchange (ETDEWEB)

This presentation outlined the energy policy in the United States and its impact on frontier development in Alaska, deepwater offshore fields and in the western oil shale resources. The energy strategy focuses on technologies that increase domestic production from existing resources as well as technologies that create new sources of energy. In addition to emphasizing the cooperation between Canada and the United States in ensuring energy supply security and stability, this paper discussed the importance of overall bilateral trade between the 2 countries. It was noted that Canada is the United State's most secure and reliable energy partner and is the number 1 supplier of imported oil, natural gas, electricity and uranium. The Bush administration's energy policy is based on the mandate to supply stable, reliable, secure, affordable and environmentally sound energy for the country's growing economy. The energy strategy focuses on increasing ...

Energy Technology Data Exchange (ETDEWEB)

In the food, chemical and safety industry there is a demand for gas detectors for process control applications, like quality control of food or leakage control in chemical plants. Gas sensor array systems have the potential to be used in this areas, with the advantage of being also affordable systems compared to other systems like gaschromatographs (GC) or infrared detectors (NIR, FTIR). One of the main drawbacks of the gas sensors is their response to non interesting ambient factors like temperature, pressure and humidity. Metal oxide sensors (MOS) have a low ambient temperature and pressure dependency. Some of them (SnO + dopands) have some sensitivity to humidity. In many cases the response of the sensors is often non-linear, which implies a concentration dependant pattern of the samples. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A High Performance Power System (HIPPS) is being developed. This system is a coal-fired, combined cycle plant with indirect heating of gas turbine air. Foster Wheeler Development Corporation and a team consisting of Foster Wheeler Energy Corporation, Bechtel Corporation, University of Tennessee Space Institute and Westinghouse Electric Corporation are developing this system. In Phase 1 of the project, a conceptual design of a commercial plant was developed. Technical and economic analyses indicated that the plant would meet the goals of the project which include a 47 percent efficiency (HHV) and a 10 percent lower cost of electricity than an equivalent size PC plant. The concept uses a pyrolyzation process to convert coal into fuel gas and char. The char is fired in a High Temperature Advanced Furnace (HITAF). The HITAF is a pulverized fuel-fired boiler/air heater where steam is ...

International Nuclear Information System (INIS)

The guide describes a method acceptable to the NRC staff for complying with the Commission's regulations with regard to quality assurance requirements for installation, inspection, and testing of mechanical equipment and systems for water-cooled and high-temperature gas-cooled nuclear power plants.

Energy Technology Data Exchange (ETDEWEB)

This report describes Northern Indiana Public Service Co. project efforts to develop an automated energy distribution and reliability system. The purpose of this project was to implement a database-driven GIS solution that would manage all of the company's gas, electric, and landbase objects.

CERN Document Server

RFID technology is gaining adoption on an increasing scale for tracking and monitoring purposes. Wide deployments of RFID devices will soon generate an unprecedented volume of data. Emerging applications require the RFID data to be filtered and correlated for complex pattern detection and transformed to events that provide meaningful, actionable information to end applications. In this work, we design and develop SASE, a com-plex event processing system that performs such data-information transformation over real-time streams. We design a complex event language for specifying application logic for such transformation, devise new query processing techniques to effi-ciently implement the language, and develop a comprehensive system that collects, cleans, and processes RFID data for deliv-ery of relevant, timely information as well as storing necessary data for future querying. We demonstrate an initial prototype of SASE ...

Energy Technology Data Exchange (ETDEWEB)

This article reports on the UN Environment Programme's (UNEP's) work in supporting the banking and financing sector by creating clean energy finance markets in developing countries. Details are given of the shifting of cash markets to credit, financing solar home systems in India, solar thermal lending in Tunisia, the financing of hotel based solar water heating in Morocco, and the Green Village Credit initiatives in the Yunnan province of China. The importance of providing banks with information needed to gain awareness and experience of renewable energy systems is stressed. The fundamentals of a bank engagement programme, financial catalysts, structuring market oriented approaches, and linking bank lending to policy making are discussed along with the need to shift to credit enhancements to help banks set up their first loan portfolios.

Energy Technology Data Exchange (ETDEWEB)

For light water reactors, loss of coolant is an important point in safety analysis, whereas for gas-cooled reactors the ingress of water into the core region is an incident of safety relevance. The applicability of the computer code system GAMTEREX to pebble beds of spherical high-temperature gas-cooled reactor fuel elements with simulated water ingress is verified by experiment. The measurements were performed at a Siemens-Argonaut reactor, using its ring core as a driver zone for a pebble-bed core in the center of the reactor.

Energy Technology Data Exchange (ETDEWEB)

This paper discusses the successful implementation of automatic control in the Wattenberg Gas Field in northern Colorado. Also discussed is the use of solar powered Amocams equipment to affect continuous monitoring and control of these tight gas wells. The control system includes an algorithm which continuously adjusts the production cycling based on changes in the individual well's producing pressures and flow rates. This strategy has been successful in enhancing production and reducing the number of wells logged off due to excessive fluid buildup. The benefits derived from this system are enumerated and the impacts on field operations are discussed.

Energy Technology Data Exchange (ETDEWEB)

Concerning the above, it is discussed whether such a system is feasible in Japan. A zinc/air cell system requires some special plants for zinc regeneration, etc. It is necessary to build a zinc refining plant and to install dozens of electrode replacing facilities in an area dozens of kilometers in diameter with the plant at the center. For such a system to be functional, there have to be several tens of thousands of automobile users in a limited area. In Japan, so large a number will not be found anywhere even if the appeal is directed to those in the postal service and electric utilities. There will be no economic success in Japan, different from in Germany. As for the economic comparison between a zinc/air cell system and natural gas system, the two will be equivalent to each other as far as the use of the quick filling stations for the natural ...

Energy Technology Data Exchange (ETDEWEB)

A new procedure for an efficient and sparing cleaning procedure of turbines was developed. The procedure uses cleaning and passivation chemicals that solve effectively and homogeneously salt and ferrous oxide coatings from turbines, avoiding attacks from corrosion, plugging and unbalances. In several high-pressure and condensation turbines the cleaning procedure has been already put into practice. (orig.)

Wastenet

... Most of the received offers were ecolabelled cleaning products and were not more expensive than conventional products. Case 3: The procurement of sustainable cleaning services 104kB Eight cooperating municipalities in the Netherlands needed a new contractor for cleaning services. They wanted to use SPP criteria as well as finding a social employment organisation. SPP criteria for cleaning services were used to set minimum requirements in ...

Science.gov (United States)

The U.S. Department of Energy and EPRI have co-funded this project to improve the control of mercury emissions from coal-fired power plants equipped with wet flue gas desulfurization (FGD) systems. The project investigated catalytic oxidation of vapor-pha...

Science.gov (United States)

The report gives results of a 4-year study to determine environmentally sound methods for disposing of wastes from nonregenerable flue gas desulfurization (FGD) systems. Data presented incorporates results obtained during the fourth year with material from report EPA-600/7-77-052...

International Nuclear Information System (INIS)

The uranium target of a gas jet transport system for fission products has been modified by the addition of an aluminum cover foil. The new modification allows fission fragments of low mass to enter a continuous chemistry system while heavier fragments are stopped in the aluminum. The elimination of the heavier homologues allows development of simpler and faster chemical separation procedures. In addition, since the lighter fragments are slowed down by the cover foil a smaller target chamber can be used. This leads to a reduction in system holdup time. (orig.).

International Nuclear Information System (INIS)

Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These ...

Energy Technology Data Exchange (ETDEWEB)

Two-phase flow in horizontal parallel channels has been experimentally investigated under fuel cell related operating conditions. Pronounced hysteresis is observed in the pressure drop versus flow characteristic curve when starting from either flooded or dry conditions. When gas is introduced into channels initially filled with water (flooded initial condition), both gas and liquid tend to flow predominantly in one channel at low gas or liquid flow velocities. As the gas flow velocity increases, even distribution of gas and liquid flow in both channels is observed, accompanied with a sudden decrease in the pressure drop. On the other hand, even gas and liquid flow distribution between both channels is found at comparatively lower gas flow velocities when starting with dry-gas flow conditions with liquid introduced into ...

International Nuclear Information System (INIS)

Electricity generation from natural gas in gas turbine units can be made substantially more efficient by preliminary methane conversion to a synthesis gas containing hydrogen and carbon monoxide and/or by the use of some of the synthesis gas produced in industry. An alternative improvement involves the introduction of solid oxide fuel cells (SOFCs) and the use of the synthesis gas in them. In this study, a modified scheme of gas turbine cycle that includes an SOFC, a membrane reactor (instead of a traditional combustion chamber), and a catalytic reactor to perform methane conversion to produce hydrogen (synthesis gas) is proposed. Variations of the energy and exergy efficiencies of the integrated system with operating conditions are provided, showing, for example, that SOFC efficiency is enhanced if the fuel cell active ...

Science.gov (United States)

One of the energy-saving devices used on gas cooking appliances to eliminate the standing pilot is a spark ignition system. For safety, an ignition system must start promptly and be active whenever flowing gas is not ignited. To minimize noise and nuisance shock hazard, ignition must occur quickly and the sparking must be stopped as soon as ignition occurs and remain off as long as the flame is present. To accomplish both of these requirements, ignition systems have been devised which use the electrical current rectification property of a flame to sense it. These systems spark whenever the gas valve is on and a flame is not present. The factors affecting the performance of a spark ignition system are numerous, complex, and transient. All of these properties make quantification of performance difficult. A ...

International Nuclear Information System (INIS)

This report presented some quick facts about oil and gas pipelines in Turkey and presented opportunities for trade. The key players and customers in the oil and gas sector were described along with an export check list. Turkey is looking into becoming an energy bridge between oil and gas producing countries in the Middle East, Central Asia and Europe. The oil and gas sectors are dominated by the Turkish Petroleum Corporation, a public enterprise dealing with exploration and production, and the State Pipeline Corporation which deals with energy transmission. They are also the key buyers of oil and gas equipment in Turkey. There are several pipelines connecting countries bordering the Caspian Sea. Opportunities exist in the areas of engineering consulting as well as contracting services for oil and gas pipeline transmission and distribution. Other opportunities ...

Energy Technology Data Exchange (ETDEWEB)

The fuel-injection system of the Niigata 6L 16X-AG dual-fuel engine is structured to steadily supply injected fuel during diesel-engine operation, and to distribute oil at a low rate to all the cylinders during gas-engine operation. The dual-fuel engine is started by the diesel engine operation and is changed over to gas-engine operation when the load increases. This change over is done automatically with a link mechanism. Regarding the gas-supply system, the changing pressure of supply gas is controlled by a pressure control valve which is stable and most adequate for the engine. The dual-fuel engine has the following features: (1) a high compression ratio is adopted, which reduces fuel consumption and thermal efficiently; (2) if the supply of gas decreases or stops, while continuing loaded operations, it can immediately shift to diesel ...

Energy Technology Data Exchange (ETDEWEB)

Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies in rapidly-growing economies in the developing world will be an essential component of global efforts to alter the path of ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the development and use of the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The model, developed in a spreadsheet format, estimates the full fuel- cycle emissions and energy use associated with various transportation fuels for light-duty vehicles. The model calculates fuel-cycle emissions of five criteria pollutants (volatile organic compounds, carbon monoxide, nitrogen oxides, sulfur oxides, and particulate matter measuring 10 microns or less) and three greenhouse gases (carbon dioxide, methane, and nitrous oxide). The model also calculates the total fuel-cycle energy consumption, fossil fuel consumption, and petroleum consumption using various transportation fuels. The GREET model includes 17 fuel cycles: petroleum to conventional gasoline, reformulated gasoline, clean diesel, liquefied petroleum gas, and electricity via residual oil; natural gas to ...

Science.gov (United States)

The Gas Research Institute established the Gas Appliance Technology Center (GATC) in 1982 to develop improved gas appliances. Between 1986 and 1992, the scope of GATC activities at Battelle included technology transfer and overall industry support, residential appliances, commercial appliances, and residential space conditioning. The following tasks are representative of the GATC activities described in the report; gas burner technology, appliance venting, emissions, water heating, range/oven technology, self-powered appliances, commercial cooktop burners, reconstituting ovens, appliance reliability improvement, combination space-heating/water-heating systems, condensing heat exchangers, corrosion testing, and space heating technology. The report includes references to available sources for further reading.

Energy Technology Data Exchange (ETDEWEB)

One of the countermeasures for exhaust emissions from a diesel engine, especially, DI diesel engine, is the use of a super high pressure injection system with a small hole diameter. However, the system needs greater driving force than that with normal injection pressure,and its demerit is an increase in NO{sub x}, although soot decreases. The authors propose a new concept, the simultaneous reduction of NO{sub x} and soot. The concept is that the utilization of flash boiling phenomenon in a diesel engine. The phenomenon can be realized by use of the injection of fuel oil with CO{sub 2} gas dissolved. Flash boiling facilities the distinguished atomization of fuel oil and CO{sub 2} gas contributes to the internal EGR (Exhaust Gas Recirculation) during combustion. Fundamental information on the characteristics of a flash boiling spray of n-tridecane with CO{sub 2} ...

Energy Technology Data Exchange (ETDEWEB)

The report reviews the activity during the fourth year of Gas Research Institute's Gas Appliance Technology Center program. Work on gas appliances involved a conceptual table-top multi-function oven, development of an indirect-fired conveyor oven, and performance comparisons of smooth cooktops. Performance-evaluation methods for commercial ovens were evaluated. Design improvements were made to a direct-fired conveyor oven and a pulse-combustion deep-fat fryer. Performance of common vents were studied, and a device was designed to allow incorporation of appliances with positive vent pressures into such systems. Standards-related work included draft-hood capacities, flexible corrugated-connector corrosion, and sediment trap efficiencies. Heating-related work comprised conceptual design of a vented baseboard heater and a centralized heat-transfer fluid system.

Science.gov (United States)

Described herein is a system for the co-generation of hydrogen gas and electricity, wherein the proportion of hydrogen to electricity can be adjusted from 0% to 100%. The system integrates fuel cell technology for power generation with fuel-assisted steam-electrolysis. A hydrocarbon fuel, a reformed hydrocarbon fuel, or a partially reformed hydrocarbon fuel can be fed into the system.

Energy Technology Data Exchange (ETDEWEB)

This paper consists of two parts. Part 1 deals with the thermodynamic and thermoeconomic methodology of a trigeneration (TRIGEN) system with a rated output of 6.5 MW gas-diesel engine while the application of the methodology is presented in Part 2. The system has been installed in the Eskisehir Industry Estate Zone in Turkey. Thermodynamic methodology includes the relations and performance parameters for energy and exergy analysis, while thermoeconomic methodology covers the cost balance relations, cost of products and thermodynamic inefficiencies, relative cost difference and exergoeconomic factor. (author)

Energy Technology Data Exchange (ETDEWEB)

Back in 1985 it was the European Commission's intention to demonstrate on rather large scale the provision of clean and renewable energy with hydrogen as energy vector and fuel. The cheapest and technologically available form of renewable electricity, the primary energy for electrolytic hydrogen, is hydropower. Most of the hydroenergy sources are oversea's. The World's topologically and technically exploitable hydroenergy potential is estimated to be in the order of 20.10{sup 3} TWh/y, i.e. 0.0057% of the hydraulic cycle energy. Today's hydroelectricity generation is {approx}2500 TWh/y i.e. {approx}21% of the World's electricity generation. Quebec's installed hydroelectricity is 33.5 GW, its residual potential is 50 GW or 190 TWh/y and 285 TWh/y, respectively (load factor 0.65). The construction of hydropower installation is rather clean. The construction of La Grande at James Bay with an ...

Energy Technology Data Exchange (ETDEWEB)

This project evaluated the feasibility of using a low-concentration (approx. 0.5 wt %) chemical cleaning process to remove corrosion product deposits from steam generator surfaces and magnetite from tube-to-support plate crevices of PWR steam generators. The primary objective was to develop a dilute process that could be safely applied at scheduled intervals, such as during normal refueling outages, to maintain a clean operating condition in the steam generator. The dilute chemical cleaning process developed in this project was demonstrated successfully on two model generators which were operated on faulted chemistry by DOE/CRC at Commonwealth's State Line Facility. Unit 5 was cleaned after 48 days of operation with 1% seawater fouling, and Unit 6 was cleaned after 112 days of operations with Lake Michigan water. This report describes work leading to the model generator ...

British Library Electronic Table of Contents (United Kingdom)

Introduction: Patients in underdeveloped nations have limited access to life-saving medical technology including cardiac rhythm management (CRM) devices. We evaluated alternative means to provide such technology to this patient population while assessing the safety and efficacy of such a practice. Methods: Patients in the United States with clinical indications for extraction of CRM devices were consented. Antemortem CRM devices were cleaned and sterilized following a protocol established at our institution. Surveillance in vitro cultures were performed for quality assurance. The functional status of pulse generators was tested with a pacing system analyzer to confirm at least 70% battery life. Most generators were transported, in person, to an implanting institution in Nicaragua. Recipien...

International Nuclear Information System (INIS)

The initial growth process and surface structure of thin Pd(silicide) films on clean Si(111)-7x7 surfaces have been studied by low energy ion scattering (ISS) and LEED-Auger techniques. Considerable reaction between Pd and Si at room temperature is observed to extend up to 25 ML thickness of deposited Pd. Heat treatment of the room temperature film produced epitaxial silicide Pd_2Si(0001) films covered with the accumulated elementary Si layers of 1-2 ML thickness. Deposition of 1/3 ML Pd onto a heated substrate gives a Pd-embedded ordered surface of Si(111)-#sq root#3x#sq root#3R30"0, the feature being similar to the cases of Ag, Au/Si(111) systems. (orig.).

CERN Document Server

The LHCb experiment has chosen to use the SAM framework (Service Availability Monitoring Environment from EGEE-II) [1] make extensive tests of the LHCb environment at all the accessible grid resources. The availability and the proper definition of the local Computing and Storage Elements, user interfaces as well as the WLCG software environment are checked. The SAM framework is also used to pre-install the LHCb applications in the shared software area provided by each site. The deployment of the LHCb applications is based on a python tool developed inside the experiment. It is used for software management including incremental installation of interdependent packages and clean package removal. After the application software is installed a validation test of the whole MC chain is run. According to the results of the experiment specific SAM tests, the sites are (re)integrated into the LHCb production system managed by DIRAC [2]. The possibility of ...

International Nuclear Information System (INIS)

The Commissariat a l'Energie Atomique (CEA, French Atomic Energy Commission) has set up over the last 10 years an innovative methodology aiming at characterizing radiological contaminations. The application of the latter relies on various tools such as expertise vehicles with impressive detection performances (VEgAS) and recently developed software platform called Kartotrak. A Geographic Information System tailored to radiological needs constitutes the heart of the platform; it is surrounded by several modules aiming at sampling optimization (Stratege), data analysis and geostatistical modeling (Krigeo), real-time monitoring (Kartotrak- RT) and validation of cleaning efficiency (Pescar). This paper presents the different tools which provide exhaustive instruments for the follow-up of decontamination projects, from doubt removal to the verification of the decontamination process. (authors)

British Library Electronic Table of Contents (United Kingdom)

Three complementary impact welding technologies are described in this paper. They are explosive welding, magnetic pulse welding, and laser impact welding, which have been used to provide metallurgical bonds between both similar and dissimilar metal pairs. They share the physical principle that general impact-driven welding can be carried out by oblique impact but are used at different length scales from meters to sub-millimeter. The different length scales require different kinds of systems to drive the process, and the scales themselves can give different weld morphologies. Metallographic analysis on cross-sections shows a wavy interface morphology which is likely the result of an instability associated with jetting, which scours the surfaces clean during impact. The normalized period and...

Energy Technology Data Exchange (ETDEWEB)

An apparatus for measuring the overall decontamination factors of first and second filters located in a plenum. The first filter separates the plenum's upstream and intermediate chambers. The second filter separates the plenum's intermediate and downstream chambers. The apparatus comprises an aerosol generator that generates a challenge aerosol. An upstream collector collects unfiltered aerosol which is piped to first and second dilution stages and then to a laser aerosol spectrometer. An intermediate collector collects challenge aerosol that penetrates the first filter. The filtered aerosol is piped to the first dilution stage, diluted, and then piped to the laser aerosol spectrometer which detects single particles. A downstream collector collects challenge aerosol that penetrates both filters. The twice-filtered aerosol is piped to the aerosol spectrometer. A pump and several valves control the movement of aerosol within the apparatus.

Energy Technology Data Exchange (ETDEWEB)

This project dealt with use of condensing heat exchangers to recover water vapor from flue gas at coal-fired power plants. Pilot-scale heat transfer tests were performed to determine the relationship between flue gas moisture concentration, heat exchanger design and operating conditions, and water vapor condensation rate. The tests also determined the extent to which the condensation processes for water and acid vapors in flue gas can be made to occur separately in different heat transfer sections. The results showed flue gas water vapor condensed in the low temperature region of the heat exchanger system, with water capture efficiencies depending strongly on flue gas moisture content, cooling water inlet temperature, heat exchanger design and flue gas and cooling water flow rates. Sulfuric acid vapor condensed in both the high temperature ...

International Nuclear Information System (INIS)

There are several concerns which bring to consider natural gas as a viable alternative to liquid fuels in transport. First, natural gas allows the curbing of global pollution in this steadily growing industry. Indeed, decoupling greenhouse gas emissions from transport growth has become a major issue in tackling climate change. Second, a more extensive use of natural gas would relieve city air quality, which is presently at levels harmful of human health. Nonetheless, this is just one side of the coin. The other side entails building a refuelling station network, and this carries financial requirements. The financing fraction holds a pivotal role in deciding whether natural gas for automotive purposes is an efficient solution. The final aim of this work is, therefore, to compare the natural gas advantages, stemming from avoided global and local emission, with the ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion control on gas pipelines plays an important role on the assessment of pipeline integrity and reliability. In many countries a great extension of buried pipelines is used on transport and distribution systems. This extension will be certainly increased in a near future due to the increasing consumption of natural gas. Inadequate corrosion control can drive to pipeline failures, bringing up the possibility of accidents in populated or environmental protected areas, bringing together severe economical, legal and environmental consequences. Corrosion is frequently considered as a natural and inevitable phenomenon. Based upon this assumption, some recommendations are included on design standards of gas pipelines in order to compensate its detrimental effect. The aim of this work is to present a review of the correlation between external corrosion process and the guidelines established during the ...

Energy Technology Data Exchange (ETDEWEB)

The vacuum system of the XVTS (X-Ray Vacuum Transport System) for the LCLS (Linac Coherent Light Source) XTOD (X-ray Transport, Optics and Diagnostics) system has been analyzed and configured by the Lawrence Livermore National Laboratory's NTED (New Technologies Engineering Division) as requested by the SLAC/LCLS program. The system layout, detailed analyses and selection of the vacuum components for the XTOD tunnel section are presented in this preliminary design report. The vacuum system was analyzed and optimized using a coupled gas load balance model of sub-volumes of the components to be evacuated. Also included are the plans for procurement, mechanical integration, and the cost estimates.

Energy Technology Data Exchange (ETDEWEB)

As a counter measure to protect against global warming, the development of CO{sub 2} recovery technology from fossil fuel power plant flue gas has continued. MEA processes are widely used for CO{sub 2} recovery from combustion flue gas in average use etc. However, if we consider power plant scale CO{sub 2} recovery, the biggest theme is the reduction of energy needed to recover CO{sub 2}. The paper focuses on sterically hindered amines and a new absorber packing. Also optimum steam system analysis results are indicated. 1 ref., 16 figs., 3 tabs.

International Nuclear Information System (INIS)

By comparison of standard entropies theoretically calculated and determined from gas-chromatographic data for 40 halo-aliphatic and halo-aromatic compounds 8 organic iodine compounds among them, adsorbed on graphitized thermal carbon black it was found that in all the cases the molecular model of ideal two-dimensional gas is a sufficiently good approximation. It was shown that for a number of systems the agreement can be improved if the vibrations of the center of molecular mass relative to the surface are taken into account

Energy Technology Data Exchange (ETDEWEB)

The Kyoto Protocol is often described as a good first step towards reducing greenhouse gas (GHG) emissions into the atmosphere. The Protocol endorses emissions trading, joint implementation including 'bubbling' between Annex 1 Parties, and a clean development mechanism that allows Annex 1 and non-Annex 1 Parties to act together to reduce emissions. However, the anticipated permit market will not function if uncertainties are not rigorously assessed and considered in any compliance process. With no reliable verification tool, it is impossible to effectively assess the different mechanisms and activities mentioned under the Protocol. Thus, it is very important to study the uncertainties underlying the Kyoto relevant GHGs, here with reference to Poland, because without the consideration of uncertainty robust verification can not occur. This paper presents information about the data used in the calculations as well as the methods ...

Energy Technology Data Exchange (ETDEWEB)

Cooperation for low carbon and energy efficient development is a high priority for France, in line with the United Nations Framework Convention on Climate Change. France contributes to tackling climate change by working with its partners on all continents to implement projects both to mitigate greenhouse gas emissions and to adapt to climate change. Within the framework of the Marrakech Accords, France also encourages the implementation of the Kyoto Protocol Clean Development Mechanism, in particular between French business and non-Annex I countries; this mechanism will facilitate the financing of mitigation projects and contribute to the sustainable development of host countries in the South. At multilateral level, France is a major donor. At a bilateral level, an initial analysis of cooperation projects which are strongly linked to tackling climate change identified public support of 136 millions euros per year, as an average over the past ...

Energy Technology Data Exchange (ETDEWEB)

Coal demineralization mechanism and its optimum condition were studied by hydrothermal reaction between Ca(OH)2 and quartz as a coal demineralization model. In experiment, the mixture of powder quartz and Ca(OH)2 water slurry was subjected to reaction in an autoclave under spontaneous pressure at 175-340{degree}C. After dried in N2 gas atmosphere at 105{degree}C, the reaction product was analyzed by X-ray diffraction, thermo-balance and differential thermal analysis. In measurement of quartz conversion, the specimen was analyzed by X-ray diffraction after removal of bound water by heat treatment at 850{degree}C. The mixture of clean coal deashed by NaOH and a fixed amount of quartz was also used as specimen for experiment. As the experimental result, dicalcium silicate hydrate was mainly produced at 175{degree}C, and the product changed into xonotlite through tobermorite by longer treatment at higher temperature. For complete reaction of ...

Energy Technology Data Exchange (ETDEWEB)

Investigation of co-gasification of biomass-coal blends in oxygen-containing atmosphere was carried out in a pressurized fluidized bed gasifier. Different biomass materials including wood and energy crop were used in the study, whereas the coal used was in bituminous rank from UK, The gasifier used was a Laboratory Development Unit (LDU) with an inner diameter of 144 mm. The operation temperature and pressure were varied in the investigation. The research was part of the European Union's Joule Ill clean coal technology programme. The study was focused on possible synergies in the thermochemical treatment of the fuel blends. The char formed was examined. The tar produced in the process was analyzed. The environmentally concerned nitrogen compounds emitted from the process were detected. Interesting synergies were observed in the experimental study. The blends of the fuels and their char formed in situ demonstrated unexpected high reaction rate of ...

Energy Technology Data Exchange (ETDEWEB)

An initial review was conducted of the current treatment operations for remediation of groundwater contaminated with trichloroethene (TCE) at the Fort lewis Logistics Center. Results from this review indicate the two pump-and-treat systems are effectively containing the TCE plume within the upper unconfined aquifer (Vashon Drift). However, mass balance calculations show the existing treatment systems alone will not accomplish the remedial action objective of cleaning up the aquifer to drinking water standards within 30 years as specified in the Record of Decision (ROD). This conclusion is based on the estimated mass of TCE at the source term (51,000 kg), the calculated mass of TCE in the aquifer (4,900 kg), and the removal rate of the pump-and-treat systems that currently ranges from 324 to 667 kg of TCe per year. Four areas within the TCE plume have been identified where enhancements could be made to ...

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little difference in TCOD removal ...

Energy Technology Data Exchange (ETDEWEB)

This document provides stakeholder evaluations on innovative technologies to be used in the remediation of volatile organic compounds from soils and ground water. The technologies evaluated are; in-well vapor stripping, in-situ bioremediation, and gas membrane separation.

International Nuclear Information System (INIS)

Comparison of plasma density increase was carried out in outer and inner channels of the interferometer in T-11M tokamak. There were two cases of gas puffing: by outer valve or upper one. Amplitude of difference of the plasma density increase consisted of 9% near the outer valve. Perturbation of the electric potential e?1/Te can have similar value. This perturbation can lead to appearance of the additional losses.

Energy Technology Data Exchange (ETDEWEB)

This document contains the outline and viewgraphs used in the speech. Topics covered are: conventional oil and gas recovery; unconventional oil and gas sources; oil shale resources; conventional coal combustion; advanced fossil power systems; fluidized bed combustion; coal/oil or coal/water mixtures; and gaseous and liquid fuels from coal. (DMC)

Energy Technology Data Exchange (ETDEWEB)

An advanced ceramic dome cavity receiver is discussed which heats pressurized gas to temperatures above 1800/sup 0/F (1000/sup 0/C) for use in solar Brayton power systems of the dispersed receiver/dish or central receiver type. Optical, heat transfer, structural, and ceramic material design aspects of the receiver are reported and the development and experimental demonstration of a high-temperature seal between the pressurized gas and the high-temperature silicon carbide dome material is described.

Energy Technology Data Exchange (ETDEWEB)

The development of a gas-operated diffusion absorption heat pump for the heating of living spaces is described. By various improvement an energy efficiency of the prototypes of 1.5 was achieved. Structural alterations led to a lower overall height and lower production costs. The CFCs used in electric heat pumps were replaced by environmentally neutral ammonia. Compared with conventional gas heating systems, the CO2 output could be reduced by more than 30%. figs., tabs.

Energy Technology Data Exchange (ETDEWEB)

This article describes a new natural-gas-fired combined cycle cogeneration plant in Bellingham, Washington. The topics of the article include community impact, siting constraints, natural gas fuel, the flexibility provided by the steam turbine, the cooling tower and pumps, air-quality, noise, and cooling water system constraints, and community relations program.

Energy Technology Data Exchange (ETDEWEB)

A gas tracer technique based on carbon monoxide and a commercial automotive exhaust gas analyser has been applied to wind tunnel models of waterjet propulsion systems intakes. The post-processing and interpretation of the carbon monoxide concentration signals has yielded high resolution measurements of the bounding ingestion stream-tubes. (orig.) With 3 figs., 1 tab., 8 refs.

Energy Technology Data Exchange (ETDEWEB)

This report describes the work carried out to analyze and design a circuit for use in 1200 kV gas insulated substations. The first part of the project was devoted to a thorough analysis of the requirements for the circuit breaker from the standpoint of the electrical system in which it would operate. A conceptual design was selected and all of the components of the circuit breaker were designed, modeled and verified. Finally a plan was prepared for the construction of a complete circuit breaker.

Science.gov (United States)

Persistently high concentrations of carbon monoxide and low-altitude ozone in the air of the Nation's major urban centers led Congress in the 1990 Clean Air Act Amendments to mandate changes to the composition of gasoline and diesel fuel. Those gasoline c...

Science.gov (United States)

Mineral scale formation in water distribution piping impedes flow, resulting in pressure and volume reduction and increasing operational costs. Chemical cleaning is both costly and time consuming, and there are health concerns when chemically cleaning pot...

Science.gov (United States)

The Bureau of Mines and ASARCO Inc. entered a cooperative agreement to determine the feasibility of producing copper matte in an electric furnace from blends of copper concentrate similar to those currently smelted in a gas-fired reverberatory system at A...

Energy Technology Data Exchange (ETDEWEB)

This article consists of a series of manufacturer's descriptions outlining specifications of underground monitoring equipment which range in complexity from gas sensitive personal badges to full mine monitoring systems. 8 figs.