WorldWideScience
1

The mass dependence of the signal peak height of a Bragg-curve ionization chamber  

International Nuclear Information System (INIS)

The Bragg-curve detector of the parallel plate ionization chamber type generates a signal that is a distorted replica of the original Bragg-curve. In result of this distortion, the signal peak height is not only a function of the atomic number of the heavy ion, as it is often stated, but also of the particle mass. This mass effect was studied with the aid of computer simulation, and it was found to be dependent on the Frisch grid to anode gap width and on the detector gas. The charge resolution of the detector is affected very significantly by this mass dependence of the signal peak height. Therefore, a careful selection of the detector gas and the grid to anode gap width is necessary, if good charge resolution over a wide range of heavy ions is required. (orig.).

2

Mass dependence of the signal peak height of a Bragg-curve ionization chamber  

Energy Technology Data Exchange (ETDEWEB)

The Bragg-curve detector of the parallel plate ionization chamber type generates a signal that is a distorted replica of the original Bragg-curve. In result of this distortion, the signal peak height is not only a function of the atomic number of the heavy ion, as it is often stated, but also of the particle mass. This mass effect was studied with the aid of computer simulation, and it was found to be dependent on the Frisch grid to anode gap width and on the detector gas. The charge resolution of the detector is affected very significantly by this mass dependence of the signal peak height. Therefore, a careful selection of the detector gas and the grid to anode gap width is necessary, if good charge resolution over a wide range of heavy ions is required.

1985-01-01

3

Analysis of natural convection in narrow annular gaps of LMFBR  

International Nuclear Information System (INIS)

The natural convection characteristics of gas in a vertical narrow annular gap which had its bottom opened to high temperature fluid and its upper shielding exposed to low temperature sealant have been evaluated from simulated fluid experiments using water and from calculations using the three-dimensional thermal hydraulic analysis computer code THERVIS-III. The following results were obtained: (1) The critical Rayleigh number which represented the limit of convection generation increased as the aspect ratios #epsilon#_1 (height/circumference) and #epsilon#_2 (height/gap distance) increased. (2) The flow pattern along the circumferential direction was seen to depend more strongly on the radiant heat from the side wall, rather than the aspect ratios #epsilon#_1 and #epsilon#_2. (3) The temperature difference along the circumferential direction in the annular gap obtained from the calculation code ...

4

An PB?-73C vacuum spark gap with a control circuit based on an inductive energy storage  

British Library Electronic Table of Contents (United Kingdom)

The design and operating principle of a small (50 mm in diameter and 100 mm in height) ???-73C vacuum spark gap are described. It is shown that it can be efficiently switched using a control circuit with a low (?900 V) supply voltage, which is based on an inductive energy storage and a diode opening switch that forms a high-voltage igniting pulse with a rise time of nanosecond duration. The ???-73C switching process is investigated at different rise times of igniting voltage pulses and different igniting current amplitudes. The results of tests of the spark gap operating in regimes of switching current pulses with an amplitude of 12 kA and a rise time of 800 ns are presented.

2011-01-01

5

Preliminary studies of coolant by-pass flows in a prismatic very high temperature reactor using computational fluid dynamics  

Energy Technology Data Exchange (ETDEWEB)

Three dimensional computational fluid dynamic (CFD) calculations of a typical prismatic very high temperature gas-cooled reactor (VHTR) were conducted to investigate the influence of gap geometry on flow and temperature distributions in the reactor core using commercial CFD code FLUENT. Parametric calculations changing the gap width in a whole core length model of fuel and reflector columns were performed. The simulations show the effects of core by-pass flows in the heated core region by comparing results for several gap widths including zero gap width. The calculation results underline the importance of considering inter-column gap width for the evaluation of maximum fuel temperatures and temperature gradients in fuel blocks. In addition, it is shown that temperatures of core outlet flow from gaps and channels are strongly affected by the ...

2009-09-01

6

Possible two-gap superconductivity in NdFeAsO{sub 0.9}F{sub 0.1} probed by point-contact Andreev-reflection spectroscopy  

Energy Technology Data Exchange (ETDEWEB)

Systematic studies of the NdFeAsOF superconducting energy gap using point-contact Andreev-reflection (PCAR) spectroscopy are presented. At low temperatures the PCAR conductance spectra show a pair of gap-like peaks at about {+-} (4-7) mV and in most cases also a pair of humps at around {+-} 10 mV. Fits to the s-wave two-gap model of the PCAR conductance allowed to determine two superconducting energy gaps in the system. However, the energy-gap features disappear at T* = 15-20 K, much below the particular T{sub c} of the junction under study. At T* a zero-bias conductance (ZBC) peak emerges, which at higher temperatures usually overwhelms the spectrum with an intensity significantly higher than the conductance signal at lower temperatures. Possible causes of this unexpected temperature effect are discussed. In some cases the conductance spectra show just a ...

2009-01-15

7

Acoustic tunneling through artificial structures: From phononic crystals to acoustic metamaterials  

British Library Electronic Table of Contents (United Kingdom)

We present a comparative study on the acoustic tunneling through artificial periodical composites, from phononic crystals to acoustic metamaterials. We find that the features of the acoustic tunneling are closely related with the origins of band gaps. In particular, the band gap associated with the negative effective material parameter in the metamaterial results in a better analog of the tunneling effect to the quantum system.

2011-01-01

8

Effect of rib height and pitch of the thermal performance of a passage disturbed by detached solid ribs  

Energy Technology Data Exchange (ETDEWEB)

Laser holographic interferometry and pressure measurements are presented for the effects of rib-to-duct height ratio (H/2B), rib pitch-to-height ratio (Pi/H), and Reynolds number (Re) on the spatially periodic-fully developed turbulent heat transfer and friction in a rectangular duct of width-to-height ratio of 4:1 with an array of ribs detached from one wall at a clearance to rib-height ratio of 0.38. The ranges of H/2B, Pi/H, and Re examined were 0.13 to 0.26, 7 to 13, and 5 {times} 10{sup 3} to 5 {times} 10{sup 4}, respectively. The difference in the H/2B dependence of the thermal performance between the detached and attached solid-rib array is documented H/2B = 0.17 and Pi/H = 10 are found to provide the best thermal performance for the range of parameters tested. Compact heat transfer and friction correlations are developed. Additionally, it is found that heat transfer ...

1998-07-01

9

Structural, electronic and optical properties of ZnX and CdX compounds (X = Se, Te and S) under hydrostatic pressure  

International Nuclear Information System (INIS)

The structural, electronic and optical properties of ZnX and CdX (X = Se, Te and S) are studied using density functional theory by the Wien2k package. The energy band gap, real and imaginary parts of the dielectric function, energy loss function, optical absorption coefficient and reflectivity spectra of these compounds are calculated. The Engel-Vosko approach improves the energy band gaps of ZnX and CdX compounds. The calculated optical parameters are in good agreement with available experimental results, particularly in the Engel-Vosko approach. Furthermore the effect of hydrostatic pressure on the energy band gap, the real and imaginary parts of the dielectric function of these compounds is studied. The first and second order pressure coefficient for the energy band gaps, the static dielectric function and the static reflectivity spectra are calculated.

2010-09-03

10

STM studies of CDWs in pure and doped transition metal chalcogenides  

Energy Technology Data Exchange (ETDEWEB)

The effects of dilute impurity doping on charge-density wave (CDW) structures and gaps in NbSe{sub 3} 1T-TaS{sub 2} and 2H-NbSe{sub 2} have been studied by using a scanning tunneling microscope (STM) operating at 4.2 K. In Fe doped samples of NbSe{sub 3} the STM spectroscopy measurements indicate that the added impurities can significantly shift the CDW energy gaps. In NbSe{sub 3}, Fe reduces both CDW gaps by 25-30%, and produces changes in the conductance structure relative to the pure material. The images of Fe{sub 0.01}NbSe{sub 3} show that all three surface chains in the unit cell still carry a strong CDW modulation with no evident disorder. However, a change in the relative amplitudes of the high and low temperature CDWs is detected. The effects of Co and Ni impurities on the gaps in NbSe{sub 3} have also been studied. While Co increases both by 25-30%, Ni ...

1992-12-01

11

High frequency breakdown voltage  

Energy Technology Data Exchange (ETDEWEB)

This report contains information about the effect of frequency on the breakdown voltage of an air gap at standard pressure and temperature, 76 mm Hg and O{degrees}C, respectively. The frequencies of interest are 47 MHz and 60 MHz. Additionally, the breakdown in vacuum is briefly considered. The breakdown mechanism is explained on the basis of collision and ionization. The presence of the positive ions produced by ionization enhances the field in the gap, and thus determines the breakdown. When a low-frequency voltage is applied across the gap, the breakdown mechanism is the same as that caused by the DC or static voltage. However, when the frequency exceeds the first critical value f{sub c}, the positive ions are trapped in the gap, increasing the field considerably. This makes the breakdown occur earlier; in other words, the breakdown voltage is lowered. As the frequency increases ...

1992-03-01

12

Gap-junctional communication of bone marrow stromal cells is resistant to irradiation in vitro  

Energy Technology Data Exchange (ETDEWEB)

Bone marrow is one of the most radiosensitive organs. Irradiation causes a marked decrease in the total number of hematopoietic cells in the bone marrow. The reticular meshwork structure of marrow stromal cells, however, is relatively resistant to irradiation. Unimpaired stromal cell structure has been thought to be a prerequisite for the repopulation of hematopoietic cells during recovery from the effects of irradiation. The reticular framework is maintained by cell adhesion apparatuses such as gap junctions. The in vitro radiobiologic survival values of a cloned stromal cell line, H-1/A, were studied (n = 1.8, D0 = 138 cGy). Radiation doses of up to 4000 cGy had no detectable effects on the production of colony-stimulating factor 1. H-1/A cells communicate with each other via gap junctions as determined by the sensitive dye-transfer method. Gap-junctional communication between ...

1990-10-01

13

Gap-junctional communication of bone marrow stromal cells is resistant to irradiation in vitro  

International Nuclear Information System (INIS)

Bone marrow is one of the most radiosensitive organs. Irradiation causes a marked decrease in the total number of hematopoietic cells in the bone marrow. The reticular meshwork structure of marrow stromal cells, however, is relatively resistant to irradiation. Unimpaired stromal cell structure has been thought to be a prerequisite for the repopulation of hematopoietic cells during recovery from the effects of irradiation. The reticular framework is maintained by cell adhesion apparatuses such as gap junctions. The in vitro radiobiologic survival values of a cloned stromal cell line, H-1/A, were studied (n = 1.8, D0 = 138 cGy). Radiation doses of up to 4000 cGy had no detectable effects on the production of colony-stimulating factor 1. H-1/A cells communicate with each other via gap junctions as determined by the sensitive dye-transfer method. Gap-junctional communication between ...

14

Extraction of biologic particles by pumping effect in a p-shaped ultrasonic actuator  

British Library Electronic Table of Contents (United Kingdom)

This paper presents a new method of extracting biologic particles from a mixture of particles. The method is based on the pumping effect in a p-shaped ultrasonic actuator, which has a gap between its two vibrating metal plates. An adhesive tape is placed at a proper position in the gap. Due to the pumping effect which is induced by the sound field in the gap, the particles with smaller mass and radius in the mixture can be pumped up to reach the adhesive tape; while the ones with larger mass cannot. Therefore, the particles with smaller mass and radius can be extracted from the mixture. A theoretical model which can well explain the operation principle and experimental phenomena is developed. By the experimental results and the theoretical analyses based on the model, the validity of the m...

2006-01-01

15

The use of combinatorial topographical libraries for the screening of enhanced osteogenic expression and mineralization  

British Library Electronic Table of Contents (United Kingdom)

Nano- and microstructured surfaces are known to impact on the binding and differentiation of cells, but the detailed basic understanding of the underlying regulatory mechanisms is still scarce, which impedes the rational design of smart biomaterials. Towards a comprehensive analysis of the interplay between topographical parameters such as feature design and lateral and vertical dimensions we here report on a combinatorial screening approach, BioSurface Structure Array (BSSA) of test squares each with a distinct topography. Using such BSSA libraries of 504 topographically distinct surface structures, we have identified combinations of size, gap and height of structures which enhance mineralization as well as the expression of osteogenic markers of a preosteoblastic murine cell line. This g...

2009-01-01

16

Assessing potential impacts of climatic change on subalpine forests on the eastern Tibetan Plateau  

British Library Electronic Table of Contents (United Kingdom)

Forest gap models have been used widely in the study of forest dynamics, including predicting long-term succession patterns and assessing the potential impacts of climate change on forest structure and composition. However, little effort is devoted to predict forest dynamics in the high elevation areas, although they have the sensitive response to global climate change. In the present study, based on a modified height-diameter function, we developed a new version (FAREAST-GFSM) of the forest patch model, FAREAST for simulating the changes of subalpine forests. The observed data from the Gongga Mt. Alpine Station were also used to test model precision. With the improved performance of FAREAST-GFSM, we explored the impact of three warming scenarios on subalpine forest on the eastern Tibetan ...

2011-01-01

17

Effect of Li-Al co-doping on the energy gaps of MgB2  

International Nuclear Information System (INIS)

We studied the effects of co-doping with Li and Al on the energy gaps of MgB2 by performing point-contact Andreev-reflection spectroscopy (PCAR) in polycrystalline Mg1-x(Al?Li1-?)xB2 samples with x?0.4. Even though the lattice parameters and the critical temperature of the compound simply scale with the effective Al content ?x, irrespective of the Li concentration, the energy gaps do not. In particular, for a given effective Al content, the comparison with Mg1-y(Al)yB2 with y = ?x shows that the ? bandgap is practically the same while the ? bandgap is higher. A clear gap merging is observed in the most doped sample (x = 0.4) when Tc<20 K. The results are discussed within the two-band Eliashberg theory and compared to the outcomes of first-principles calculations of the effects of Li and Al co-doping on the electronic structure of ...

2009-02-01

18

Mechanism of electrical breakdown of gases for pressures from 10?9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm  

Science.gov (United States)

This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.

2007-08-01

19

Mechanism of electrical breakdown of gases for pressures from 10"-"9 to 1 bar and inter-electrode gaps from 0.1 to 0.5 mm  

International Nuclear Information System (INIS)

This paper discusses the mechanisms of gas breakdown at low values of pressure and inter-electrode gap, i.e. in the vicinity of the Paschen minimum. In this area of pressure and inter-electrode gap values, breakdown occurs either through gas or vacuum mechanisms, and also the so called anomalous Paschen effect appears. Electrical breakdown of electropositive, electronegative and noble gases has been investigated theoretically, experimentally and numerically. Based on the results obtained, regions in which particular breakdown mechanisms appear have been demarcated. Special attention has been devoted to the anomalous Paschen effect as well as to the avalanche vacuum breakdown mechanism.

2007-08-01

20

Triosephosphates Modulate Leaf Mitochondrial Phosphorylation by Inhibition and Uncoupling of Electron Transport 1  

UK PubMed Central (United Kingdom)

The effect of TP (triosephosphates:glyceraldehyde-3 phosphate, GAP, +dihydroxyacetone phosphate, DHAP) on respiration, phosphorylation and matrix ATP/ADP ratios of isolated oat mesophyll mitochondria...Full Text Available

1985-11-01

21

On the change of pore distribution in the course of coking and its effect on the gap tensile strength and the modulus of elasticity of coke. Zur Veraenderung der Porenverteilung im Verlauf der Verkokung und deren Auswirkung auf die Spaltzugfestigkeit und den Elastizitaetsmodul von Koksen  

Energy Technology Data Exchange (ETDEWEB)

A model describes the effect of changes to the pore structure on the mechanical properties of semi-coke during coking. The gap tensile experiment makes it possible to determine the mechanical properties of the coke and semi-coke; a theoretical analysis is valid for the deformation of samples in the gap tensile test, by which the gap tensile strength of the coke can be determined, and by which a method for the simultaneous determination of the effective modulus of elasticity was developed. The effect of the pore structure on the mechanical properties is given in semi-empirical equations. The main point here is to check whether a pore in the coke can be regarded as a Griffith crack, and whether the interaction of pores can be neglected. A model which takes the pore distribution into account was also developed and tested. A model for the change of pore structure ...

1984-01-01

22

Effect of elevated temperatures on the performance of an InP cell illuminated by a selective emitter  

Energy Technology Data Exchange (ETDEWEB)

The thermophotovoltaic (TPV) option was not selected for further deep space mission technology development in NASA for several reasons. Chief among them was the large radiator required to keep the photovoltaic cells at a sufficiently low operating temperature. This led to significant integration problems with the spacecraft and limited sensor view angles. It is clear that the issue of cell temperature is crucial for space applications because of radiator size and system impact. Many efforts have focused on matching cell band gap to appropriate emitters in the 1 to 2 {mu}m range, resulting in band gaps in the 0.5 to 0.8 eV range. However, low band gaps lead to low open circuit voltages ({approximately}0.25 to 0.45 V) caused by high intrinsic carrier concentrations (n{sub i}{sup 2}). Thus, in order to obtain high performance. Photovoltaic cell temperatures must be kept near room temperature. This leads to the inevitable ...

1999-03-01

23

Parametric study of the amplification factor in the energy balance method  

Energy Technology Data Exchange (ETDEWEB)

This paper represents a parametric study of the amplification factor to account for rebound effects in the Energy Balance Method. Of the 66 distinct cases we chose for our parametric study, the amplification factor of 1.1 seems sufficient except in four borderline cases where the carbon steel pipes are small or have very small gaps between the pipes and the pipe whip restraints. We conclude that the amplification factor generally decreases as the parameters gap size, hinge-to-break distance and overhang increase.

1985-04-01

24

Experimental study on heat transfer augmentation for high heat flux removal in rib-roughened narrow channels  

Energy Technology Data Exchange (ETDEWEB)

Frictional pressure drop and heat transfer performance in a very narrow rectangular channel having one-sided constant heat flux and repeated-ribs for turbulent flow have been investigated experimentally, and their experimental correlations were obtained using the least square method. The rib pitch-to-height ratios(p/k) were 10 and 20 while holding the rib height constant at 0.2mm, the Reynolds number(Re) from 2,414 to 98,458 under different channel heights of 1.2mm, 2.97mm, and 3.24mm, the rib height-to-channel equivalent diameter(k/De) of 0.03, 0.04, and 0.09 respectively. The results show that the rib-roughened surface augments heat transfer 2-3 times higher than that of the smooth surface with the expense of 2.8-4 times higher frictional pressure drop under Re=5000-10{sup 5}, p/k=10, and H=1.2mm. Experimental results obtained by channel height, H=1.2mm shows a little bit higher ...

1997-07-01

25

Point-contact Andreev-reflection spectroscopy in MgB{sub 2}: The role of substitutions  

Energy Technology Data Exchange (ETDEWEB)

We summarize the results of point-contact Andreev-reflection (PCAR) spectroscopy in MgB{sub 2} doped by chemical substitutions, either magnetic (Mn) or non-magnetic (Al,C), obtained by us and by other groups in the last four years. Despite the variety of samples used (crystals and polycrystals of various origin) and some minor differences in the experimental techniques, these measurements have directly provided a complete and consistent picture of the effects of chemical substitutions on the gaps of MgB{sub 2} shedding light on other relevant parameters (scattering rates, DOSs) affected by doping. In Al-doped crystals and polycrystals, the gap amplitudes {delta}{sub {sigma}} and {delta}{sub {pi}} - obtained through a two-band Blonder-Tinkham-Klapwijk (BTK) fit of the Andreev-reflection conductance curves - decrease on increasing the Al content x (i.e. on decreasing the critical temperature of the contacts T{sub c}{sup A}), ...

2007-06-01

26

Quantitative genetic activity graphical profiles for use in chemical evaluation  

International Nuclear Information System (INIS)

A graphic approach, terms a Genetic Activity Profile (GAP), was developed to display a matrix of data on the genetic and related effects of selected chemical agents. The profiles provide a visual overview of the quantitative (doses) and qualitative (test results) data for each chemical. Either the lowest effective dose or highest ineffective dose is recorded for each agent and bioassay. Up to 200 different test systems are represented across the GAP. Bioassay systems are organized according to the phylogeny of the test organisms and the end points of genetic activity. The methodology for producing and evaluating genetic activity profile was developed in collaboration with the International Agency for Research on Cancer (IARC). Data on individual chemicals were compiles by IARC and by the US Environmental Protection Agency (EPA). Data are available on 343 compounds selected from volumes 1-53 of the IARC ...

1990-06-27

27

Counter-current air-water flow in narrow rectangular channels with offset strip fins  

Energy Technology Data Exchange (ETDEWEB)

Counter-current two-phase flows of air-water in narrow rectangular channels with offset-strip fins have been experimentally investigated in a 760 mm long and 100 mm wide test section with 3.0 and 5.0 mm gap widths. The two-phase flow regime, channel-average void fractions and two-phase pressure gradients were studied. Flow regime transition occurred at lower superficial velocities of air than in the channels without fins. In the bubbly and slug flow regimes, elongated bubbles rose along the subchannel formed by fins without lateral movement. The critical void fraction for the bubbly-to-slug transition was about 0.14 for the 3 mm gap channel and 0.2 for the 5 mm gap channel, respectively. Channel-average void fractions in the channels with fins were almost the same as those in the channels without fins. Void fractions increased as the gap width increased, especially at high superficial velocity of air. ...

2003-03-01

28

Simulation of carbon dioxide absorption by sodium hydroxide solution in a packed bed and studying the effect of operating parameters on absorption  

International Nuclear Information System (INIS)

Available in abstract form only. Full text of publication follows: In this study. simulation of carbon dioxide absorption by Sodium Hydroxide solution in a packed bed has been investigated. At first, mass and energy balances were applied around a differential height of the bed. So, the governing equations were obtained. Surface renewal theory by Danckwerts was used to represent the mass transfer operation Finally, by changing the operating parameters like solvent temperature, inlet gas composition pressure and height of the bed, the effect of these parameters on the absorption and the composition of carbon dioxide in exit stream have been investigated. (authors)

2007-09-02

29

Enhancing productivity of Indian basil (Ocimum basilicum L.) through harvest management under rainfed conditions of subtropical north Indian plains  

British Library Electronic Table of Contents (United Kingdom)

A field experiment was conducted during 2004 and 2005 at the research farm of Central Institute of Medicinal And Aromatic Plants, Lucknow located at 26.5^o N 80.5^o E and 120m above the mean sea level to study the effect of harvesting stage and cutting height on growth, yield and quality of Indian basil. The objective of this study was to increase the essential oil yield of Indian basil without adverse effect on quality by taking two harvests through manipulating harvesting stage and cutting height and to increase the land and rain water utilization efficiency under rain fed condition. The treatments consisted of four stages of first harvest (40, 60, 80 and 100 days after transplanting (DAT)) and three cutting height (0, 7.5 and 15.0cm above ground level). The Indian basil (Ocimum basilicu...

2010-01-01

30

Defect influence on the T/sub c/ of A-15 compounds  

Science.gov (United States)

The defect-induced electron lifetime and energy-gap anisotropy effects on the T/sub c/ of the A-15 compounds are examined. A self-consistent model calculation demonstrates that the various defect dependences of T/sub c/ can be qualitatively understood in terms of the electron-lifetime effect.

1979-10-01

31

Defect influence on the T/sub c/ of A-15 compounds  

International Nuclear Information System (INIS)

The defect-induced electron lifetime and energy-gap anisotropy effects on the T/sub c/ of the A-15 compounds are examined. A self-consistent model calculation demonstrates that the various defect dependences of T/sub c/ can be qualitatively understood in terms of the electron-lifetime effect.

32

Pituitary gland height evaluated by MR in patients with {beta}-thalassemia major: a marker of pituitary gland function  

Energy Technology Data Exchange (ETDEWEB)

In transfusion-dependent {beta}-thalassemia major, increased iron deposition in the pituitary gland has a cytotoxic effect leading mainly to hypogonadotropic hypogonadism. Our purpose was to assess in these patients the height of the pituitary gland and to evaluate whether it represents a marker of pituitary gland function. In 29 patients with {beta}-thalassemia major and 35 age- and gender-matched controls the pituitary gland height was evaluated in a midline sagittal scan using a spin echo T1-weighted (500/20 TR/TE) sequence. In all patients, an extensive endocrine evaluation was performed, including measurements of spontaneous and stimulated levels of gonadotropins, thyroid hormones, growth hormone, insulin-like growth factor, and adrenal hormones. The pituitary gland height was lower in thalassemic patients with hypogonadotropic hypogonadism (n=15) (mean 3.48; SD 0.46) than in the age- and ...

2001-12-01

33

Experimental investigation of mixed convection heat transfer from longitudinal fins in a horizontal rectangular channel: In natural convection dominated flow regimes  

Energy Technology Data Exchange (ETDEWEB)

Mixed convection heat transfer from longitudinal fins inside a horizontal channel has been investigated in the natural convection dominated region for a wide range of Rayleigh numbers and different fin heights and spacings. An experimental parametric study was made to investigate effects of fin spacing, fin height and magnitude of heat flux on mixed convection heat transfer from rectangular fin arrays heated from below in a horizontal channel. The optimum fin spacing to obtain maximum heat transfer has also been investigated. During the experiments constant heat flux boundary condition was realized and air was used as the working fluid. The velocity of fluid entering channel was kept nearly constant (0.02 {<=} w{sub in} {<=} 0.025 m/s) using a flow rate control valve so that Reynolds number was always about Re = 250. Experiments were conducted for modified Rayleigh numbers 3 x 10{sup 7} < Ra{sup *} ...

2009-10-15

34

Off-shell Interactions for closed-string tachyons  

Energy Technology Data Exchange (ETDEWEB)

Off-shell interactions for localized closed-string tachyons in C/Z{sub N} superstring backgrounds are analyzed and a conjecture for the effective height of the tachyon potential is elaborated. At large N, some of the relevant tachyons are nearly massless and their interactions can be deduced from the S-matrix. The cubic interactions between these tachyons and the massless fields are computed in a closed form using orbifold CFT techniques. The cubic interaction between nearly-massless tachyons with different charges is shown to vanish and thus condensation of one tachyon does not source the others. It is shown that to leading order in N, the quartic contact interaction vanishes and the massless exchanges completely account for the four point scattering amplitude. This indicates that it is necessary to go beyond quartic interactions or to include other fields to test the conjecture for the height of the tachyon potential. ...

2004-05-01

35

Off-Shell Interactions of Closed-String Tachyons  

Energy Technology Data Exchange (ETDEWEB)

Off-shell interactions for localized closed-string tachyons in C/Z{sub N} superstring backgrounds are analyzed and a conjecture for the effective height of the tachyon potential is elaborated. At large N, some of the relevant tachyons are nearly massless and their interactions can be deduced from the S-matrix. The cubic interactions between these tachyons and the massless fields are computed in a closed form using orbifold CFT techniques. The cubic interaction between nearly-massless tachyons with different charges is shown to vanish and thus condensation of one tachyon does not source the others. It is shown that to leading order in N, the quartic contact interaction vanishes and the massless exchanges completely account for the four point scattering amplitude. This indicates that it is necessary to go beyond quartic interactions or to include other fields to test the conjecture for the height of the tachyon potential.

2004-04-07

36

Experimental investigation of mixed convection heat transfer from longitudinal fins in a horizontal rectangular channel  

British Library Electronic Table of Contents (United Kingdom)

Mixed convection heat transfer from longitudinal fins inside a horizontal channel has been investigated for a wide range of modified Rayleigh numbers and different fin heights and spacings. An experimental parametric study was made to investigate effects of fin spacing, fin height and magnitude of heat flux on mixed convection heat transfer from rectangular fin arrays heated from below in a horizontal channel. The optimum fin spacing to obtain maximum heat transfer has also been investigated. During the experiments constant heat flux boundary condition was realized and air was used as the working fluid. The velocity of fluid entering channel was kept nearly constant (0.15win0.16m/s) using a flow rate control valve so that Reynolds number was always about Re=1500. Experiments were conducted...

2010-01-01

37

Effect of On-Chip Magnetic Shielding for TES Microcalorimeters  

British Library Electronic Table of Contents (United Kingdom)

We investigated the magnet field dependence of the X-ray pulse height and the critical current of a Ti/Au bilayer TES micro-calorimeter. The pulse height was strongly affected by the magnetic field intensity applied perpendicularly to the TES surface. We found that the critical current at zero temperature, I c0, decreased by a factor of two by applying a magnet field of ?10??T. Our data are consistent with a TES sensitivity proportional to (I/I c0)?2/3, as predicted by the Ginzburg-Landau theory. This fact implies that the shape of the R?T curve of the TES is partly determined by the critical current of the superconductor. In order to make our TES microcalorimeters less sensitive to the external magnetic field, we fabricated devices equipped with on-chip magnetic shielding. One device has ...

2008-01-01

38

Characterization of focused-ion-beam-induced damage in n-type silicon using Schottky contact  

International Nuclear Information System (INIS)

The effects of focused-ion-beam-induced damage on electrical properties of n-type Si are investigated by Schottky contacts. Crystalline Si is exposed to 10-30 keV focused ion beam (FIB), followed by Pt deposition under vacuum of 4x10"-"4 Pa. From current-voltage-temperature measurements, barrier heights of the Schottky contacts are found to increase almost linearly as the FIB energy increases, with the maximum increment of 0.29 eV. The increase is suggested to be related to the arising of acceptorlike defects and an amorphous layer due to FIB damages. A theoretical model is set up to quantitatively describe the barrier height changes.

2006-04-10

39

Time Average Aerodynmic Forces and Moments on a National Model of a Semi-Submersible Offshore Rig. Part 1. Measurements. Part 2. Analysis of Results for the Basic Model.  

Science.gov (United States)

Wind-tunnel measurements were taken of the time-average aerodynamic forces and moments on a notional model of a semi-submersible offshore drilling rig at two heights and at various attitudes to the wind. Attempts were made to analyze the separate effects ...

1982-01-01

40

Mathematical analysis of the length-of-arc assumption  

Energy Technology Data Exchange (ETDEWEB)

The observation by Maday in 1974 that the Schmidt-Duffin solution to the optimal fin profile problem was flawed due to neglect of the slant height factor led to a new solution--actually, a demonstration of the ill-posedness of the question--by Snider. The present article proves mathematically that omission of this factor leads inevitably to underestimation of the heat transfer capability of any fin. Additionally, a perturbation scheme for estimating the correction for this effect is derived for configurations with low generalized Biot numbers, and a revised assessment of the performance of the Schmidt fin is presented.

1996-04-01

41

Interphase mass transfer in the separation of isotopes in countercurrent columns (liquid-solid systems)  

International Nuclear Information System (INIS)

The results of calculated and experimental investigation of interphase isotopic exchange efficiency in countercurrent columns are given when separation processes of isotope mixtures are taken place with use of liquid-solid systems. Effect of liquid phase flow on transfer unit height in ion exchange separation of boron, lithium, nitrogen isotopes is considered. 40 refs.; 5 figs.

42

Effect of resin size on HETP in separation of isotopes by chromatography  

Energy Technology Data Exchange (ETDEWEB)

In this report, the quantitative relation between the height equivalent to a theoretical plate (HETP) and the size of ion exchange resin is studied by enriching lithium isotopes with high pressure ion exchange displacement chromatography. The dependence of HETP on the size of the resin can be expressed as H = C x (anti r)sup( ) in which = 2.4 and it is found that Snyder's equation is suitable for such a system of isotope separation as may be explained by the simple displacement mechanism.

1985-02-01

43

Anode wire ageing in proportional detectors at the BAC calorimeter of the ZEUS experiment  

Energy Technology Data Exchange (ETDEWEB)

Experimental results of ageing effects in proportional counters are presented. The measurements were carried out for 158 ZEUS-BAC gas system monitoring counters. Deterioration of the pulse height distribution in azimuth and along the anode wire are presented. The influence of water admixture on counting gas is also described. (orig.).

1997-06-21

44

Optical characterization of long-term ordered and nanocrystalline GaP  

International Nuclear Information System (INIS)

The paper generalizes some results of the United States/Moldova program on advanced composite organic and semiconductor light emitters. High density exciton system bound to N impurity superlattice grown by modern technologies and GaP:N, GaP:N:Sm nanocrystals distributed in transparent fluorine-containing polymers will be used as the base elements for new generation of optoelectronic devices. The work seeks to expand further the applications of GaP itself through the formation of nanocomposites. Classic and new methods are applied for preparation of GaP:N nanoparticles with the controlled dimensions developed clear quantum confinement effect. The long-term ordered bulk GaP crystals as well as their nanoparticles have been investigated by TEM, XRD, Raman scattering, and luminescent methods. The evolution of the Raman Light Scattering and luminescence spectra is reported from pure and doped GaP single ...

45

Pressure-dependent photoluminescence study of ZnO nanowires  

Energy Technology Data Exchange (ETDEWEB)

The pressure dependence of the photoluminescence (PL) transition associated with the fundamental band gap of ZnO nanowires has been studied at pressures up to 15 GPa. ZnO nanowires are found to have a higher structural phase transition pressure around 12 GPa as compared to 9.0 GPa for bulk ZnO. The pressure-induced energy shift of the near band-edge luminescence emission yields a linear pressure coefficient of 29.6 meV/GPa with a small sublinear term of -0.43 meV/GPa{sup 2}. An effective hydrostatic deformation potential -3.97 eV for the direct band gap of the ZnO nanowires is derived from the result.

2004-09-13

46

Andreev reflection spectroscopy of MgB{sub 2} in the vortex state  

Energy Technology Data Exchange (ETDEWEB)

Spectroscopy based on the Andreev reflection (AR) process at the interface between the normal metal tip and the superconductor has become one of the very successful methods for studies in novel exotic superconductors. The method is capable to address the size, symmetry as well as multiplicity of the superconducting order parameter. The method provided one of the first evidences of the two-gap superconductivity in MgB{sub 2} with a detailed temperature dependence of the both gaps. A theory treating the Andreev reflection spectroscopy in the mixed state is missing. We analyse the AR spectra of MgB{sub 2} in the mixed state via modelling the magnetic pair-breaking by the increasing spectral broadening parameter {gamma}. As a result a non-trivial pair breaking effect in the {pi}-band is found.

2004-05-01

47

The influence of stray radiation on image quality  

International Nuclear Information System (INIS)

The present state of knowledge on the influence of stray radiation on image quality and its physical description and quantification is summarized. Experimental results on the influence of physical parameters on the fraction of scattered radiation and the effect of scatter reduction by air gap technique and secondary radiation grids are committed. Open theoretical and practical problems and the limitations of common methods of scatter reduction are pointed out. (author).

48

Discrimination between UTP- and P2-purinoceptor-mediated depolarization of rat superior cervical ganglia by 4,4'-diisothiocyanatostilbene-2,2'- disulphonate (DIDS) and uniblue A.  

UK PubMed Central (United Kingdom)

1. Using a grease-gap recording technique we have investigated the effects of some antagonists of P2-purinoceptors on the depolarization of the rat isolated superior cervical ganglion evoked by 100...Full Text Available

1995-06-01

49

Cultural narratives: bridging the gap. Educating speech-language pathologists to work in multicultural populations.  

Science.gov (United States)

Preparation of the clinician to work in multicultural contexts involves the identification of a range of skills, knowledge and values. The field of narrative medicine as well as an increased understanding of the dynamics of interpreting are areas which can add considerably to clinical effectiveness. The paper outlines some cornerstones of narrative medicine and their potential application to the field of speech-language pathology and audiology. PMID:12037426

50

Cosmological BCS condensate as dark energy  

CERN Document Server

We argue that the occurrence of late-time acceleration can conveniently be described by first-order general relativity covariantly coupled to fermions. Dark energy arises as a gravitationally driven BCS condensate of fermions which forms in the early universe. At late times, the gap and chemical potential evolve to have an equation of state with effective negative pressure, thus naturally leading to acceleration.

2009-01-01

51

Cooling device for rotors of multistage axial steam turbines  

International Nuclear Information System (INIS)

The invention concerns an improvement of a cooling device for rotors of multistage axial steam turbines by providing in the first stage of each group of turbine stages a circulation loop connecting the wheel chamber on the inlet side of the rotor disc of the first stage with the wheel chamber on its outlet side. This is to cause the cooling effect not to be hampered by gap widths of the seal in the bottom range of the rotor blades changing during operation. Design particulars are described in detail. (UWI).

52

Theoretical investigation of the behavior of an acoustic metamaterial with extreme Young's modulus  

British Library Electronic Table of Contents (United Kingdom)

A mechanical model with local resonators is proposed as an acoustic metamaterial that exhibits an unusual frequency-dependent effective stiffness. If treated as an equivalent elastic solid, its effective Young's modulus can become unbounded or vanishingly small at two respective frequencies. Moreover, in a certain frequency range, the effective Young's modulus would become negative, resulting in a band gap that coincides with this frequency range. The wave attenuation behavior and mechanism are studied through numerical simulations on the acoustic metamaterial model. The capability of the metamaterial to selectively block or filter unwanted waves is demonstrated by a numerical simulation example.

2011-01-01

53

Effects of temperature and the use of macroreticular resins in lithium isotope separation by displacement chromatography  

Energy Technology Data Exchange (ETDEWEB)

The effects of temperature and the use of macroreticular resins were studied in lithium isotope separation by an ion-exchange method. The isotope separation factors obtained decreased by increasing the temperature, and the factors for macroreticular resins were identical with those for the usual gel-type resins. However, the performance of isotope separation per unit band length in displacement chromatography was found to be improved by increasing the temperature and using macroreticular resins, because accelerating the interphase mass transfer caused the reduction of HETP (Height Equivalent to a Theoretical Plate).

1983-01-01

54

Extracting energy from hydraulically-fractured geothermal reservoirs  

Science.gov (United States)

The governing equations for heat and mass transfer were derived for hydraulically fractured geothermal reservoirs. When converted to nondimensional form it was shown that the equations can be considerably simplified. The resulting equations can be strongly influenced by the effects of buoyancy; the magnitude of the effect is measured by the ratio of the Grashof and Reynolds numbers, and the ratio of the actual permeability of the fracture and the square of the fracture gap width. Significant quantities of energy can be extracted from hydraulic fractures--even without thermal stress fracturing. The amount is limited by the size of the fracture and the low thermal conductivity of rock. The viscous pressure drop in open fractures is insignificant, and depending upon losses in piping and surface equipment, the entire system could be ''self-pumped'' due to buoyancy. Thermal contraction of the ...

1976-01-01

55

Effect of parameters on performance of LNG-FPSO offloading system in offshore associated gas fields  

Energy Technology Data Exchange (ETDEWEB)

Due to the advantages of the flexibility and economics in exploration and production of offshore liquefied natural gas (LNG), the floating production storage and offloading unit for liquefied natural gas (LNG-FPSO) has attracted wide attentions in recent years. The offloading system for LNG transportation from LNG-FPSO to LNG carrier is one of the most important parts in LNG-FPSO. The influences of the main parameters such as the mass flow rate and the height difference of the pipeline. on the performance of LNG offloading in offshore associated gas fields were investigated. A model based on a typical offshore LNG offloading system was first established and simulations were conducted. The governing equations were then used to evaluate the effects of parameters together with the simulation results. It was found that there was an economic mass flow rate for practical design on balance of the cost in pump head and BOG. The ...

2010-11-15

56

Parametric study of pipe whip analysis  

Energy Technology Data Exchange (ETDEWEB)

In the Energy Balance Analysis Model (Standard Review Plan (USNRC, 1981), Section 3.6.2, ''Determination of Rupture Locations and Dynamic Effects Associated with the Postulated Rupture of Piping''), time dependence is not considered, and a constant blowdown thrust force is assumed. This force includes an amplification factor of 1.1 to account for potential effects of rebound. Many of the assumptions used in establishing the acceptance criteria, as stated in the Standard Review Plan, were based on engineering judgment and logic intended to assure upper bound design rather than on a mechanistic assessment of actual pipe rupture phenomena and their effects. As a result of the current practice an exceedingly conservative design may be introduced. This report represents a parametric study of the amplification factor to account for rebound effects in the Energy Balance ...

1987-10-01

57

Entropy, confinement, and chiral symmetry breaking  

CERN Document Server

This paper studies the way in which confinement leads to chiral symmetry breaking (CSB) through a gap equation. We argue that entropic effects cut off infrared singularities in the standard confining effective propagator $1/p^4$, which should be replaced by $1/(p^2+m^2)^2$ for a finite mass $m\\sim K_F/M(0)$ [$M(0)$ is the zero-momentum value of the running quark mass]. Extension of an old calculation of the author yields a specific estimate for $m$. This cutoff propagator shows semi-quantitatively two critical properties of confinement: 1) a negative contribution to the confining potential coming from entropic forces; 2) an infrared cutoff required by gauge invariance and CSB itself. Entropic effects lead to a proliferation of pion branches and a $\\bar{q}q$ condensate, and contribute a negative term $\\sim -K_F/M(0)$ to the effective pion Hamiltonian allowing for a massless pion ...

2010-01-01

58

Effects of the variation of fundamental constants on Pop III stellar evolution  

International Nuclear Information System (INIS)

The effect of variations of the fundamental constants on the thermonuclear rate of the triple alpha reaction, "4He(#alpha##alpha#, #gamma#)"1"2C, that bridges the gap between "4He and "1"2C is investigated. We have followed the evolution of 15 and 60 M#centre dot# zero metallicity stellar models, up to the end of core helium burning. They are assumed to be representative of the first (Population III) stars. The calculated oxygen carbon abundances resulting from helium burning can then be used to constrain the variation of the fundamental constants.

2010-08-12

59

Locally resonant acoustic metamaterials with 2D anisotropic effective mass density  

British Library Electronic Table of Contents (United Kingdom)

A two-dimensional (2D) lattice model with anisotropic resonant microstructures is found to provide an anisotropic band gap structure. A 2D continuum with anisotropic effective mass density is introduced to represent this lattice system. Two methods are proposed to derive the equivalent continuum. In the first method, the effective mass density of the equivalent continuum is obtained by matching the dispersion relations for harmonic waves propagating in the principal directions. The second approach employs an approximate estimation of the effective mass density by volume-averaging an effective mass that represents the resonant microstructure. For both equivalent continuum models, the effective mass density is frequency-dependent and may become negative in certain frequency ranges. Subsequen...

2011-01-01

60

ARM: Infrared Thermometer: Ground surface temperature averaged 60-sec at 10-meter height  

Science.gov (United States)

Infrared Thermometer: Ground surface temperature averaged 60-sec at 10-meter height

1996-04-16

61

Two dimensional power spectral density measurements of X-rayoptics with the Micromap interferometric microscope  

Energy Technology Data Exchange (ETDEWEB)

A procedure and software have been developed to transform the area distribution of the residual surface heights available from the measurement with the Micromap interferometric microscope into a two-dimensional (2D) power spectral density (PSD) distribution of the surface height. The procedure incorporates correction of one of the spectral distortions of the PSD measurement. The distortion appears as a shape difference between the tangential and sagittal PSD spectra deduced from the 2D PSD distribution for an isotropic surface. A detailed investigation of the origin of the anisotropy was performed, and a mathematical model was developed and used to correct the distortion. The correction employs a modulation transfer function (MTF) of the detector deduced analytically based on an experimentally confirmed assumption about the origin of the anisotropy due to the asymmetry of the read-out process of the instrument's CCD camera. The ...

2005-05-12

62

The use of foam to improve liquid lifting from low-pressure gas wells  

Energy Technology Data Exchange (ETDEWEB)

Gas well load up is the loss of available reservoir energy due to the accumulation of liquids in the wellbore over time, and these liquids arise from liquids (hydrocarbons and water) condensed from the gas. Accumulation of these liquids near the wellbore can cause severe reduction to complete loss of available transport energy. A systematic experimental approach was undertaken to evaluate the performance of foam in removing liquids from the bottom of wells. The objectives of the research were: (1) to determine the efficiency of liquid lifting with foam; and (2) to compare the effects of surfactant type and concentration on liquid lifting. A flowloop successfully simulated the effects of completions with and without packer for low-pressure gas well with liquid production. In the base-case runs (air and water flow), the two phase flow regime was mostly annular. Liquid lifting is improved in general when a surfactant is used. For data analysis, ...

1999-07-01

63

Influence of surface heat flux ratio on heat transfer augmentation in square channels with parallel, crossed, and V-shaped angled ribs  

Science.gov (United States)

The paper investigates the effect of the wall heat flux ratio on the local heat transfer augmentation in a square channel with two opposite in-line ribbed walls for Reynolds numbers from 15,000 to 80,000. The square channel composed of 10 isolated copper sections has a length-to-hydraulic diameter ratio of 20. The rib height-to-hydraulic diameter ratio is 0.0625 and the rib pitch-to-height ratio equals 10. Six ribbed side to smooth side wall heat flux ratios are studied for four rib orientations. The results show that the ribbed side wall heat transfer augmentation increases with increasing ribbed side to smooth side wall heat flux ratios, but the reverse is true for the smooth side wall heat transfer augmentation. The average heat transfer augmentation of the ribbed side and smooth side wall decreases slightly with increasing wall heat flux ratios. The effect of wall heat flux ratio reduces with ...

1992-10-01

64

Transport effect on He II film under conditions of weak interaction with the substrate  

Energy Technology Data Exchange (ETDEWEB)

The properties of a helium film on the surface of solid parahydrogen are investigated. It is shown that wetting of the solid hydrogen by the liquid helium occurs. The transport velocities along the He II film on the solid parahydrogen surface are measured in broad temperature, film height, and level difference ranges. It is shown that the transport velocity in this case has the least value as compared with its value on other substrates. The thickness of the helium-saturated film is determined on the solid hydrogen surface on the basis of the data obtained, and the value is in good agreement with the results of a computation performed within the framework of the Frenkel' theory.

1980-10-01

65

Selected topics in transient response of aerial lines to high-altitude electromagnetic pulse  

International Nuclear Information System (INIS)

Aerial lines or cables, as one mainly energy transport path of electronic system when illuminated by HEMP, has been often modeled by field-to-transmission line model. However, in many cases, authors too often encounter some confusing statements to the lines effects during experimental procedure. The aim of this paper is to present and discuss these cases, such as the electromagnetic environment above the ground plane, the contribution of the different electromagnetic field component to the induced current and voltage, variations of the load current for different line heights and ground conductivities etc. (authors)

2005-11-01

66

NMR study of one-dimensional ionic conductor with hollandite-type structure (IV) Rb-priderite  

International Nuclear Information System (INIS)

Conduction properties of Rb"+ ion in Rb-Al-priderite and K"+ ion and Rb"+ ion in (K,Rb)-Al-priderite, were investigated by NMR using "2"7Al in the framework as a probe. Size effect was observed remarkably in the activation energies. Frequency dependence of T_1 in Rb-Al-priderite at a low temperature indicates that the relaxation behavior of "2"7Al in Rb-Al-priderite can be described by the continuum model. Barrier height distributions and 'attempt frequencies' in both samples obtained by a curve-fitting method are discussed in comparison with those of K-Al-priderite. (orig.).

1985-08-18

67

Horizontal liquid film-mist two-phase flow. I - Concentration distribution and diffusivity of entrained liquid droplets  

Science.gov (United States)

The entrainment flow rate distribution, the gas velocity profile, and the concentration profile of droplets across the channel cross section in fully developed region of a horizontal rectangular channel of 150mm width and 50mm height were measured. The concentration profile of droplets was expressed by a simple equation based on a constant diffusion coefficient model. From this equation the effects of gravity and turbulent diffusion of droplets on the concentration profile were evaluated. The characteristic mean settling velocity of a group of droplets with various diameters was derived, and using this value the mean diffusion coefficient of the group of droplets was obtained

1980-06-01

68

Horizontal liquid film-mist two-phase flow, 1  

International Nuclear Information System (INIS)

The entrainment flow rate distribution, the gas velocity profile, and the concentration profile of droplets across the channel cross section in fully developed region of a horizontal rectangular channel of 150 mm width and 50 mm height were measured. The concentration profile of droplets was expressed by a simple equation based on a constant diffusion coefficient model. From this equation the effects of gravity and turbulent diffusion of droplets on the concentration profile were evaluated. The characteristic mean settling velocity of a group of droplets with various diameters was derived, and using this value the mean diffusion coefficient of the group of droplets was obtained. (author).

1980-01-01

69

A micro-compression study of shape-memory deformation in U-13at%Nb  

Energy Technology Data Exchange (ETDEWEB)

Micro-compression specimens, 1O-15{mu}m in diameter by 20-30{mu}m in height, were produced from individual parent grains in a polycrystalline U-13at%Nb shape-memory alloy using the focused ion beam (FIB) technique. The specimens were tested in a nanoindentation instrument with a flat diamond tip to investigate stress-strain behavior as a function of crystallographic orientation. The results are in qualitative agreement with a single-crystal accommodation strain (Bain strain) model of the shape-memory effect for this alloy.

2008-01-01

70

Band-edge solitons, Nonlinear Schrodinger / Gross-Pitaevskii Equations and Effective Media  

CERN Document Server

We consider a class of nonlinear Schrodinger / Gross-Pitaevskii (NLS/GP) equations with periodic potentials, having an even symmetry. We construct "solitons", centered about any point of symmetry of the potential. For focusing (attractive) nonlinearities, these solutions bifurcate from the zero state at the lowest band edge frequency, into the semi-infinite spectral gap. Our results extend to bifurcations into finite spectral gaps, for focusing or defocusing (repulsive) nonlinearities under more restrictive hypotheses. Soliton nonlinear bound states with frequencies near a band edge are well-approximated by a slowly decaying solution of a homogenized NLS/GP equation, with constant homogenized effective mass tensor and effective nonlinear coupling coefficient, modulated by a Bloch state. For the critical NLS equation with a periodic potential, e.g. the cubic two dimensional NLS/GP with a periodic ...

2010-01-01

71

Mid-latitude scintillation model. Technical report, 1 November 1985-31 October 1986  

Energy Technology Data Exchange (ETDEWEB)

Radiowave scintillation in the presence of ionospheric disturbances has the potential to disrupt numerous transionospheric radio and radar systems. This report describes development of a model characterizing the plasma density irregularities that produce scintillation in the naturally disturbed mid-latitude F layer. The model will be incorporated into Program WBMOD, which includes subroutines for computing both link geometry and scintillation indices, the latter by means of phase screen diffraction theory. Earlier versions of WBMOD, were based on extensive analysis of scintillation data collected in the auroral and equatorial zones in Wideband Satellite Mission. The model described herein is based on similarly extensive analysis of Wideband data from one mid latitude station and of data collected from HiLat satellite at another mid latitude station. The model describes irregularities at an effective height of 350 km that are isotropic across ...

1986-10-31

72

Heat transfer augmentation due to surface radiative exchange effect of internal fins in an annulus  

International Nuclear Information System (INIS)

Heat transfer augmentation due to surface radiation in an annulus with fins was investigated both theoretically and experimentally for fully developed laminar flow. The system considered in the present study was an array of axially internal and straight fins attached to the outer tube wall. Analytical solutions were given for 4, 8, 16, 24, 32 fins and for the ratios of the fin height to the passage clearance, 0, 0.2, 0.4, 0.5, 0.6, 0.8. The experiments were performed with air as the working fluid for radius ratio of 1.45, 16 fins and for Reynolds numbers ranging from 500 to 2000. The numerically predicted results of the convective/radiative heat transfer for the present case were in good agreement with the experimental data. It was found that the heat transfer augmentation coefficient attained a maximum value of 1.45 for 32 fins and for a dimensionless fin height of 0.65.

1987-08-01

73

Experimental investigation of mixed convection heat transfer from longitudinal fins in a horizontal rectangular channel: In natural convection dominated flow regimes  

British Library Electronic Table of Contents (United Kingdom)

Mixed convection heat transfer from longitudinal fins inside a horizontal channel has been investigated in the natural convection dominated region for a wide range of Rayleigh numbers and different fin heights and spacings. An experimental parametric study was made to investigate effects of fin spacing, fin height and magnitude of heat flux on mixed convection heat transfer from rectangular fin arrays heated from below in a horizontal channel. The optimum fin spacing to obtain maximum heat transfer has also been investigated. During the experiments constant heat flux boundary condition was realized and air was used as the working fluid. The velocity of fluid entering channel was kept nearly constant (0.02win0.025m/s) using a flow rate control valve so that Reynolds number was always about ...

2009-01-01

74

Integrated verification test of Severe Accident Analysis Code SAMPSON in super Simulation 'IMPACT' system  

International Nuclear Information System (INIS)

The Four years of the IMPACT, 'Integrated Modular Plant Analysis and Computing Technology', project Phase 1 have been completed. The verification study of Severe Accident Analysis Code SAMPSON prototype developed in Phase 1 was conducted in two steps. First, each analysis module was run independently and analysis results were compared and verified against separate-effect test data with good results. Second, with the Simulation Supervisory System, up to 11 analysis modules were executed concurrently in the parallel environment (currently, NUPEC uses IBM-SP2 with 72 process elements), to demonstrate the code capability and integrity. The target plant was Surry as a typical PWR and the initiation events were a 10-inch cold leg failure. The analysis is divided to two cases; one is in-vessel retention analysis when the gap cooling is effective (In-vessel scenario test), the other is analysis of phenomena event is extended to ...

1999-07-01

75

Evaluation of Core Bypass Flow in the Prismatic VHTR with a Multi-block Experiment  

International Nuclear Information System (INIS)

The core of Prismatic Modular Reactor (PMR) consists of assemblies of hexagonal graphite fuel and reflector elements. The core bypass flow of Very High Temperature Reactor (VHTR) is defined as the core flow that does not pass through the coolant channels but passes through the bypass gap between fuel elements. The increase in bypass flow makes the decrease in effective coolant flow. Since the core bypass flow has a negative impact on safety and efficiency of VHTR, core bypass phenomena have to be investigated to improve the core thermal margin of VHTR. For this purpose, the international project, I-NERI project, has been carried out since 2008. I-NERI project is collaborative project that KAERI and SNU of Korea side and INL, ANL and TAMU of U.S side are involved. In order to evaluate the core bypass flow, the multicolumn and multi-layer experimental facility is designed by SNU. In this experiment, the effect of cross-flow ...

2010-10-01

76

Acoustic metamaterials for sound focusing and confinement  

Energy Technology Data Exchange (ETDEWEB)

We give a theoretical design for a locally resonant two-dimensional cylindrical structure involving a pair of C-shaped voids in an elastic medium which we term as double 'C' resonators (DCRs) and imbedded thin stiff bars, that displays the negative refraction effect in the low frequency regime. DCRs are responsible for a low frequency band gap which hybridizes with a tiny gap associated with the presence of the thin bars. Using an asymptotic analysis, typical working frequencies are given in closed form: DCRs behave as Helmholtz resonators modeled by masses connected to clamped walls by springs on either side, while thin bars behave as a periodic bi-atomic chain of masses connected by springs. The discrete models give an accurate description of the location and width of the stop band in the case of the DCR and the first two dispersion bands for the periodic thin bars. We then combine our asymptotic ...

2007-11-15

77

Acoustic metamaterials for sound focusing and confinement  

International Nuclear Information System (INIS)

We give a theoretical design for a locally resonant two-dimensional cylindrical structure involving a pair of C-shaped voids in an elastic medium which we term as double 'C' resonators (DCRs) and imbedded thin stiff bars, that displays the negative refraction effect in the low frequency regime. DCRs are responsible for a low frequency band gap which hybridizes with a tiny gap associated with the presence of the thin bars. Using an asymptotic analysis, typical working frequencies are given in closed form: DCRs behave as Helmholtz resonators modeled by masses connected to clamped walls by springs on either side, while thin bars behave as a periodic bi-atomic chain of masses connected by springs. The discrete models give an accurate description of the location and width of the stop band in the case of the DCR and the first two dispersion bands for the periodic thin bars. We then combine our asymptotic formulae for arrays of ...

2007-11-01

78

Separation of lithium isotopes by counter-current flow of the coexisting phases of a lithium-ammonia solution  

Energy Technology Data Exchange (ETDEWEB)

A weak shift of the isotope concentration ratio Li{sup 6}/Li{sup 7} was measured in the coexisting phases of the miscibility gap of lithium-ammonia solutions. Li{sup 6} is slightly enriched in the concentrated metallic phase (enrichment factor {alpha} = 1.009 {+-} 0.002). This effect can be enhanced in a counter-current column to yield any desired enrichment of the two isotopes. The counter current system and its operation were tested succesfully with a sodium-potassium-ammonia solution.

1991-12-01

79

Attack Methodology Analysis: Emerging Trends in Computer-Based Attack Methodologies and Their Applicability to Control System Networks  

Energy Technology Data Exchange (ETDEWEB)

Threat characterization is a key component in evaluating the threat faced by control systems. Without a thorough understanding of the threat faced by critical infrastructure networks, adequate resources cannot be allocated or directed effectively to the defense of these systems. Traditional methods of threat analysis focus on identifying the capabilities and motivations of a specific attacker, assessing the value the adversary would place on targeted systems, and deploying defenses according to the threat posed by the potential adversary. Too many effective exploits and tools exist and are easily accessible to anyone with access to an Internet connection, minimal technical skills, and a significantly reduced motivational threshold to be able to narrow the field of potential adversaries effectively. Understanding how hackers evaluate new IT security research and incorporate significant new ideas into their own tools provides ...

2005-06-01

80

Preliminary investigation of /sup 252/Cf-driven neutron noise analysis for subcritical fuel solution systems  

Energy Technology Data Exchange (ETDEWEB)

A method for determining the reactivity of highly subcritical systems of fissile material, using neutron-noise power spectral densities in conjunction with a /sup 252/Cf source, had previousy been tested in two fast reactor critical assemblies (a mockup of the Fast Flux Test Facility reactor and unreflected enriched uranium metal assemblies) and one thermal reactor (a light-water moderated and reflected lattice of Oak Ridge Research Reactor fuel elements). The last-mentioned test demonstrated the effectiveness of the method in water-moderated systems and thereby prompted the present study of its application to facilities for fuel preparation, reprocessing, and storage. To investigate the applicability of this method to facilities for fuel preparation, reprocessing, and storage, limited experiments were performed with a uranyl fluoride solution. The Los Alamos National Laboratory SHEBA facility, an unreflected cylindrical tank (56 cm diam), was partially filled with ...

1981-01-01

81

The study of technical error analysis on BMD using DEXA  

International Nuclear Information System (INIS)

This study was conducted to search for the type of technical error in DEXA (dual-energy X-ray absorptiometry) and the effect of error to measurement of BMD. The changes of BMD (g/cm2, T-score) by patients information (Age, Weight, Height, Manopause age) input error and Confirming ROI error were investigated. Using spine phantom, we canned 10 times by age (5, 10), weight (10, 20 kg), height (5, 10 cm), manopause age (5, 10) increase and decrease respectively. Scanning region (L-spine, femur, Forearm) of 10 patients was calculated by changing ROI respectively. Analysis of difference for mean (precision 1%) were carried out. There error of patient information (Age, Weight, Height, Manopause age) was not changed differently. In confirming ROI, the BMD and T-score of L-spine involving T-12 was decreased to 0.063 g/cm2, 0.3 and involving L-5 increased to 0.077 g/cm2, 0.5. In narrowing 1 cm of vertical line of ...

2006-12-01

82

Can non-formal education keep working children in school? A case study from Punjab, India  

British Library Electronic Table of Contents (United Kingdom)

This paper analyses the effectiveness of non-formal schools for working children in Jalandhar, Punjab, India, in mainstreaming child labourers into the formal education system through incentivised, informal schooling. Using a family fixed effects model and sibling data as an equivalent population comparison group, I find that the non-formal schools effectively provide an alternative to formal primary education and also show high success rates of mainstreaming and maintaining children into post-primary education relative to the control group. I find that the children within the non-formal schools are 40.47-50.07% more likely to still be studying relative to the sibling-inclusive control group, and have 1.976 to 3.389 years less of a gap in educational attainment. I conclude that the child l...

2010-01-01

83

A Computer Simulation of the Electronic Structure of Leucine in Aqueous Solution  

British Library Electronic Table of Contents (United Kingdom)

In order to obtain the electronic structure of leucine (Leu) in aqueous solution, we studied three systems: Leu+7H2O, Leu+8H2O and Leu+9H2O. The results indicated that the system Leu+8H2O was the only choice which was both acceptable and doable: its computational effort was affordable, and it could simulate a main part of the solvent effect on the electronic structure of Leu in solution. Based on the system Leu+8H2O, all-electron, ab initio calculations were performed to construct an equivalent potential of water for the electronic structure of Leu with dipoles. The results showed that the main effect of water on the electronic structure of Leu was raising the occupied states about 0.0824 Ry on average, and broadening the energy gap by 11%. The water effect on the electronic structure of L...

2011-01-01

84

Turbulent flow in a channel with transverse rib heat transfer augmentation  

Science.gov (United States)

Turbulent flow in a 2D channel with repeated rectangular rib roughness was numerically simulated using a low Reynolds number form of the k-epsilon turbulence model. Friction factors and average Stanton numbers were calculated for various pitch to rib height ratios and bulk Reynolds numbers. Comparisons with experiment were generally adequate, with the predictions of friction superior to those for heat transfer. The effect of variable properties for channel flow was investigated, and the results showed a greater effect for friction than for heat transfer. Comparison with experiment yielded no clear conclusions. The turbulence model was also validated for a related problem, that of flow downstream of an abrupt pipe expansion.

1993-04-01

85

The effect of the venom of the yellow Iranian scorpion Odontobuthus doriae on skeletal muscle preparations in vitro  

British Library Electronic Table of Contents (United Kingdom)

The yellow Iranian scorpion Odontobuthus doriae can cause fatal envenoming, but its mechanism of action is unclear. One of the reported manifestations of envenoming is moderate to severe involuntary tremor of skeletal muscle. In order to understand better the mechanism of action of this venom on skeletal muscle function, we examined the effects of the venom in vitro on chick biventer cervicis (CBC) and mouse hemidiaphragm (MHD) nerve muscle preparations. O. doriae venom (0.3-10mg/ml) initially increased and then decreased twitch height. The venom also caused contracture in both preparations. In mouse triangularis sterni preparations, used for all intracellular recording techniques, the venom enhanced the release of acetylcholine and induced repetitive firing of nerve action potentials and ...

2007-01-01

86

Effect of spacing and nitrogen fertilization on the establishment and biomass production of short rotation Poplar in Finland  

Energy Technology Data Exchange (ETDEWEB)

Short rotation trials using cuttings poplar (Populus x rasumowskyana) in Southern Finland investigated the establishment of poplar plantations and the effects of spacing and application of nitrogen fertilizer on biomass production over a period of 6 years. Thicker cuttings grew better whilst those of less than 1 cm diameter grew only moderately. Nitrogen fertilization improved height and diameter growth and above-ground dry mass yield. Woody biomass production was 4.2 dry tons/ha per year, at 300 kg/ha nitrogen. A spacing of 15 000 stems/ha gave the best yield after 4 years, but 5000 stems/ha was more productive spacing in the next 2 years. (author).

1989-01-01

87

Effect of parameters on performance of LNG-FPSO offloading system in offshore associated gas fields  

British Library Electronic Table of Contents (United Kingdom)

Due to the advantages of the flexibility and economics in exploration and production of offshore liquefied natural gas (LNG), the floating production storage and offloading unit for liquefied natural gas (LNG-FPSO) has attracted wide attentions in recent years. The offloading system for LNG transportation from LNG-FPSO to LNG carrier is one of the most important parts in LNG-FPSO. The influences of the main parameters such as the mass flow rate and the height difference of the pipeline. on the performance of LNG offloading in offshore associated gas fields were investigated. A model based on a typical offshore LNG offloading system was first established and simulations were conducted. The governing equations were then used to evaluate the effects of parameters together with the simulation ...

2010-01-01

88

A model for Schottky-barrier solar cell analysis  

Science.gov (United States)

A general model for the analysis of metal-semiconductor solar cells is presented. The model takes into account the cell optical properties, carrier recombination effects, semiconductor minority-carrier properties, series resistance, cell thickness, and active surface area. Numerical methods are used to solve the appropriate continuity equations and hence compute the photocurrent density under AMO conditions. The operation of the model is demonstrated using p- and n-type Si and GaAs with Au being taken as the barrier metal. Calculations are presented showing the effect on solar energy conversion efficiency of surface recombination velocity, barrier height, minority-carrier lifetime, barrier metal thickness, collecting grid configuration, and cell thickness. A comparison of practical and computed data for the Au/n-GaAs system yields good agreement. (AIP)

1976-05-01

89

T=(5/2) "2"7Na from "1"4C+"1"4C, and the N=16 shell gap  

International Nuclear Information System (INIS)

For the first time a comprehensive level and decay scheme has been obtained for a T=(5/2) nucleus in the s-d shell ("2"7Na) by using a radioactive beam and target. Particle-#gamma# and p-#gamma#-#gamma# coincidences were measured following the "1"4C("1"4C,p#gamma#)"2"7Na reaction at E_l_a_b=22 MeV. The results do not support an inversion of the 2s_1_/_2 and 1d_5_/_2 orbitals, as previously proposed for T_z#>=#3, but they do suggest an increased N=16 gap between the 2s_1_/_2 and 1d_3_/_2 orbitals due to the neutron excess. A consistent interpretation of the level scheme in terms of the s-d shell model using the USD Hamiltonian is possible below 4 MeV, but differences increase at higher excitation energies. Another interpretation is that the influences of both the p_1_/_2 and f_7_/_2 intruder orbitals increase simultaneously with increasing T, an effect not included in the USD Hamiltonian.

2002-05-01

90

Reflection-Free One-Way Edge Modes in a Gyromagnetic Photonic Crystal  

CERN Document Server

We point out that electromagnetic one-way edge modes analogous to quantum Hall edge states, originally predicted by Raghu and Haldane in 2D gyroelectric photonic crystals possessing Dirac point-derived bandgaps, can appear in more general settings. In particular, we show that the TM modes in a gyromagnetic photonic crystal can be formally mapped to electronic wavefunctions in a periodic electromagnetic field, so that the only requirement for the existence of one-way edge modes is that the Chern number for all bands below a gap is non-zero. In a square-lattice gyromagnetic Yttrium-Iron-Garnet photonic crystal operating at microwave frequencies, which lacks Dirac points, time-reversal breaking is strong enough that the effect should be easily observable. For realistic material parameters, the edge modes occupy a 10% band gap. Numerical simulations of a one-way waveguide incorporating this crystal show 100% transmission across ...

2007-01-01

91

Generation of ozone by pulsed corona discharge over water surface in hybrid gas-liquid electrical discharge reactor  

International Nuclear Information System (INIS)

Ozone formation by a pulse positive corona discharge generated in the gas phase between a planar high voltage electrode made from reticulated vitreous carbon and a water surface with an immersed ground stainless steel plate electrode was investigated under various operating conditions. The effects of gas flow rate (0.5-3 litre min"-"1), discharge gap spacing (2.5-10 mm), applied input power (2-45 W) and gas composition (oxygen containing argon or nitrogen) on ozone production were determined. Ozone concentration increased with increasing power input and with increasing discharge gap. The production of ozone was significantly affected by the presence of water vapour formed through vaporization of water at the gas-liquid interface by the action of the gas phase discharge. The highest energy efficiency for ozone production was obtained using high voltage pulses of approximately 150 ns duration in Ar/O_2 mixtures with the ...

2005-02-07

92

Evidence for p-f mixing in U/sub 3/P/sub 4/ and U/sub 3/As/sub 4/ from optical spectroscopy  

Energy Technology Data Exchange (ETDEWEB)

The near normal incidence reflectivity of the ferromagnets U/sub 3/P/sub 4/ and U/sub 3/As/sub 4/ and the isostructural but diamagnetic compounds Th/sub 3/P/sub 4/ and Th/sub 3/As/sub 4/ has been measured from 0.03 to 12 eV. Trithorium tetraphosphide and tetraarsenide are shown to be indirect gap semiconductors with gap energies of 0.43 and 0.39 eV, respectively. U/sub 3/P/sub 4/ and U/sub 3/As/sub 4/ display similar sets of p..-->..d transitions than the corresponding thorium compounds, however, they are shifted by 0.85 eV to lower photon energies. It is concluded that the uranium compounds are metals due to a merging of the valence p band into the 6d conduction band giving direct experimental evidence for a p-f mixing effect of the same size. Energy level schemes are derived.

1983-07-01

93

Evidence for p-f mixing in U"3P"4 and U"3As"4 from optical spectroscopy  

International Nuclear Information System (INIS)

The near normal incidence reflectivity of the ferromagnets U"3P"4 and U"3As"4 and the isostructural but diamagnetic compounds Th"3P"4 and Th"3As"4 has been measured from 0.03 to 12 eV. Trithorium tetraphosphide and tetraarsenide are shown to be indirect gap semiconductors with gap energies of 0.43 and 0.39 eV, respectively. U"3P"4 and U"3As"4 display similar sets of p#->#d transitions than the corresponding thorium compounds, however, they are shifted by 0.85 eV to lower photon energies. It is concluded that the uranium compounds are metals due to a merging of the valence p band into the 6d conduction band giving direct experimental evidence for a p-f mixing effect of the same size. Energy level schemes are derived. (author).

1983-01-01

94

Band parameters for III - V compound semiconductors and their alloys  

International Nuclear Information System (INIS)

We present a comprehensive, up-to-date compilation of band parameters for the technologically important III - V zinc blende and wurtzite compound semiconductors: GaAs, GaSb, GaP, GaN, AlAs, AlSb, AlP, AlN, InAs, InSb, InP, and InN, along with their ternary and quaternary alloys. Based on a review of the existing literature, complete and consistent parameter sets are given for all materials. Emphasizing the quantities required for band structure calculations, we tabulate the direct and indirect energy gaps, spin-orbit, and crystal-field splittings, alloy bowing parameters, effective masses for electrons, heavy, light, and split-off holes, Luttinger parameters, interband momentum matrix elements, and deformation potentials, including temperature and alloy-composition dependences where available. Heterostructure band offsets are also given, on an absolute scale that allows any material to be aligned relative to any other. ...

2001-06-01

95

Semiconductor-metal transition of pyrite FeS_2 under high pressure by full-potential linearized-augmented plane wave calculations  

International Nuclear Information System (INIS)

The effects of hydrostatic pressure on the electronic band structure of the semiconductor mineral iron pyrite FeS_2 have been investigated theoretically by an ab initio full-potential linearized-augmented plane wave (FPLAPW) method within a local approximation (LDA/GGA) to the density functional theory. The calculations predict that at a pressure of 94.1 GPa the indirect band gap of pyrite FeS_2 vanishes and the material becomes a metal. This is due to the presence of the S-S and Fe-S bonds, which provide novel energy band distortions in the process of attaining the metallic state. Analysis indicates that, under increasing high pressure, the conduction bands (3p_z of sulfur and 3d_x_"2_-_y_"2+3d_x_y of iron) intrude downwards into the valence bands, which are predominantly 3d in nature. At normal pressure, the lattice constant, the bulk modulus, sulfur position parameter u, S-S bond length, and the indirect band gap of ...

2006-10-11

96

Computational Fluid Dynamic Analysis of Core Bypass Flow Phenomena in a Prismatic VHTR  

Energy Technology Data Exchange (ETDEWEB)

The core bypass flow in a prismatic very high temperature gas-cooled reactor (VHTR) is one of the important design considerations which impacts considerably on the integrity of reactor core internals including operating fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) will be affected by the bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to understand better the bypass flow phenomenon and establish the evaluation method in the reactor core using commercial CFD code FLUENT. Parametric ...

2010-09-01

97

Paracardioscopic Ex-Maze  

Medline Plus

... the pulmonary vein and because there's a gap, electricity is going across the ablation line and capturing ...

98

Evolution of ultraviolet dwarfs  

Science.gov (United States)

UV dwarf star evolution, using central and gap star models emphasizing photoneutrino emission

1969-01-01

100

Synergistic effect of different phase on the photocatalytic activity of visible light sensitive silver antimonates  

British Library Electronic Table of Contents (United Kingdom)

We investigated phase transition of ilmenite-type AgSbO3 to pyrochlore by post-heat treatment and the synergy effect of the mixed phases of AgSbO3 on the photocatalytic activities to enhance the activities. The AgSbO3 with an ilmenite structure was prepared by a cation-exchange method. Phase transition from the ilmenite to pyrochlore occurred by proper control of post-heat treatment. The sample that was obtained by post-heat treatment of ilmenite-type AgSbO3 at 660^oC for 3h consisted of both of the ilmenite and pyrochlore phases, and the sample at 685^oC for 4h mainly consisted of the pyrochlore phase. Together with an increase in the ratio of the pyrochlore phase, the optical absorption spectra blue-shifted. The band gaps of single phases of the ilmenite and the pyrochlore were 2.4 and 2...

2010-01-01

101

Optical properties and electronic structure of ceramics tetragonal PbTiO_3 by using full-potential linearized augmented plane wave  

International Nuclear Information System (INIS)

The electronic structure and optical properties in tetragonal ceramics PbTiO_3, are studied by using full-potential linearized augmented plane wave method in density functional theory with the generalized gradient approximation by WIEN2K package. The theoretical calculated optical properties and energy loss spectrum yield a static refractive index of 2.59 and a plasmon energy of 22.7eV for the tetragonal phase. The effective electron number at low energy saturates near 22-23eV with the value of 50 for the effective electron number. The results show a indirect band gap of 2.2eV at the I' point in the Brillouin zone. The :calculated band structure and density of states of PbTiO_3 agree with previous experimental and theoretical results.

2007-01-01

102

Magnetization transfer contrast effect on multislice fast spin echo  

Energy Technology Data Exchange (ETDEWEB)

Magnetization transfer contrast (MTC) on fast spin echo (FSE) images was evaluated in normal brain tissue as well as in brain tumors to better understand contrast of FSE images. On multislice FSE images, attenuation of the signal intensity of brain tissue due to MTC is observed. The rate of MTC (MTR) is obtained by comparing with additional single slice images. The effect of signal attenuation is greater on images with smaller interslice gap, larger number of slices, and longer echo train length. MTR of brain tumors is less than that of normal brain tissue. Among them, meningiomas have relatively high MTR, and cavernous malformation has relatively low MTR. Determination of MTC can be easily specified by obtaining multislice and single slice FSE images, and it may help differentiate brain tumors. (author).

1994-03-01

103

Homogenation of acoustic metamaterials of Helmholtz resonators in fluid  

Energy Technology Data Exchange (ETDEWEB)

By using a two-step homogenization approach, we derive analytical formulas of effective mass density {rho}{sub e} and effective bulk modulus B{sub e} for two- and three-dimensional acoustic metamaterials of Helmholtz resonators (HRs) in fluid. A negative B{sub e} is found at certain frequencies due to the monopolar resonance, leading to a low-frequency acoustic band gap. A unified picture is presented for metamaterials of HRs and three-component metamaterials of negative {rho}{sub e}. Our work supports recent observations in a one-dimensional array of HRs [N. Fang et al., Nat. Mater. 5, 452 (2006)] and presents important high-dimensional extensions for exploring more fascinating phenomena.

2008-05-01

104

Geothermal Casimir Phenomena  

CERN Document Server

We present first worldline numerical results for the nontrivial interplay between geometry and temperature dependencies of the Casimir effect. We show that the temperature dependence of the Casimir force can be significantly larger for open geometries (e.g., perpendicular plates) than for closed geometries (e.g., parallel plates). For surface separations in the experimentally relevant range, the thermal correction for the perpendicular-plates configuration exhibits a stronger parameter dependence and exceeds that for parallel plates by more than an order of magnitude at room temperature. This effect can be attributed to the fact that the fluctuation spectrum for closed geometries is gapped, inhibiting the thermal excitation of modes at low temperatures. By contrast, open geometries support a thermal excitation of the low-lying modes in the gapless spectrum already at low temperatures.

2007-01-01

105

Computational fluid dynamic analysis of core bypass flow phenomena in a prismatic VHTR  

International Nuclear Information System (INIS)

The core bypass flow in a prismatic very high temperature reactor (VHTR) is an important design consideration and can have considerable impact on the condition of reactor core internals including fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) are affected by bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to better understand bypass flow phenomena and establish an evaluation method for the reactor core using the commercial CFD code FLUENT. Parametric calculations changing several factors ...

2010-09-01

106

Validation of the Canadian atmospheric dispersion model for small exclusion area boundaries  

International Nuclear Information System (INIS)

AECL is undertaking the validation of ADDAM, an atmospheric dispersion and dose code based on the Canadian Standards Association model CSA N288.2. The key component of the validation program involves the comparison of air concentrations predicted by the model with measured values. Measurements are available from field studies at two Canadian reactor sites and from a wind tunnel study of the CANDU site at Wol song, Korea. The measurements were obtained close enough to the release points to test the model for exclusion area boundaries as small as 500 m. Model predictions were higher than the observations almost 75 percent of the time and the magnitude of the over predictions was typically much larger than the magnitude of the under predictions. The effect of the topography at the Wol song site was limited to small changes in plume trajectory due to channeling in valleys and a small reduction in the lateral spread of the plume. The terrain did not substantially ...

1999-11-04

107

The impact of smoking in primary spontaneous pneumothorax  

British Library Electronic Table of Contents (United Kingdom)

Background The crucial role of cigarette smoking in the development of pneumothorax is unclear because nonsmokers can also develop primary spontaneous pneumothorax. The purpose of this study was to clarify the pathophysiologic effects of cigarette smoking and its clinical correlations in primary spontaneous pneumothorax. Methods Included were 115 specimens of lung tissue from patients with primary spontaneous pneumothorax who underwent video-assisted thoracoscopic surgery from January 2001 to December 2002. We reviewed the clinical features of 56 smokers and 59 nonsmokers with an average follow-up of 67 months. The pathologic findings of resected lung specimens were analyzed retrospectively. Results There were no statistical differences in sex, age, body height, body weight, body mass inde...

2009-01-01

108

Stack behavior under influence of mining  

Energy Technology Data Exchange (ETDEWEB)

Evaluates effects of longwall mining of black coal seams in the Lower Silesian coal basin on industrial stacks. Deviation of three stacks in the Walbrzych coking plant was measured one year long. The stacks, constructed in 1902-1904, and reconstructed in 1937-1938 were made of stack bricks. Foundations of the 54.00 m, 52.80 m and 64.50 m high stacks were situated at depths of 4.00 to 5.50 m. Ground subsidence and curvature were analyzed. Direction of stack deviation in relation to the direction of longwall mining was evaluated. Analyses showed there was no correlation between direction of stack deviation and ground inclination. Deviation, which increased with growing stack height, depended on displacement of stack foundations. 3 refs.

1989-01-01

109

Stability of modulation transfer function calibration of surface profilometers using binary pseudo-random gratings and arrays with nonideal groove shapes  

Energy Technology Data Exchange (ETDEWEB)

The major problem of measurement of a power spectral density (PSD) distribution of surface heights with surface profilometers arises due to the unknown Modulation Transfer Function (MTF) of the instruments, which tends to distort the PSD at higher spatial frequencies. The special mathematical properties of binary pseudo-random patterns make them an ideal basis for developing MTF calibration test surfaces. Two-dimensional binary pseudo-random arrays (BPRAs) have been fabricated and used for the MTF calibration of the MicroMap{trademark}-570 interferometric microscope with all available objectives. An investigation into the effects of fabrication imperfections on the quality of the MTF calibration and a procedure for accounting for such imperfections are presented.

2010-03-31

110

Multiscale morphology analysis and its application to fault diagnosis  

Science.gov (United States)

A novel approach to fault diagnosis is proposed using multiscale morphology analysis to extract impulsive features from the signals with strong background noise. Multiscale morphology is applied to one-dimensional signal by defining both the length and height scales of structuring elements (SEs). A local-peak-value based adaptive algorithm is also introduced. The new approach makes the selection of SEs more transparent and is independent of empirical rules. Both simulated impulsive and vibration signals of two defective roller bearings are employed to validate the proposed algorithm. The roller bearing faults presented in the validation include both inner and outer race faults. The test results show that the multiscale morphology analysis is effective and robust to extract morphological features.

2008-04-01

111

Monitoring noise-resonant effects in cancer growth influenced by spontaneous fluctuations and periodic treatment  

CERN Document Server

In the paper we investigate a mathematical model describing the growth of tumor in the presence of immune response of a host organism. The dynamics of tumour and immune cells is based on the generic Michaelis-Menten kinetics describing interaction and competition between the tumour and the immune system. The appropriate phenomenological equation modeling cell-mediated immune surveillance against cancer is of the predator-prey form and within a given choice of parameters exhibits bistability. Under the influence of spontaneous weak fluctuations, the model may be analyzed in terms of a stochastic differential equation bearing the form of an overdamped Langevin-like dynamics in the external quasi-potential represented by a double well. We analyze properties of the system within the range of parameters for which the potential wells are of the same depth and when the additional perturbation describing a periodic treatment is insufficient to overcome the barrier height ...

2007-01-01

112

Mixed convection in a horizontal rectangular channel - Experimental and numerical velocity distributions  

Science.gov (United States)

Mixed convection in a rectangular channel (width/height = 2) with bottom-heated and top-cooled sections is studied by laser Doppler anemometry in nitrogen at Ra = 22,200 and Re = 18.75, 36, and 54. At the lower Re values, symmetry breaking is observed in steady but spatially oscillating flows that prevail over a certain distance from the leading edge of the differentially heated section. Further downstream, unsteady flows are found even for Re = 18.75. Numerical models are used to investigate the effects of adiabatic, conducting (with a conductive-convective heat transfer coefficient), and perfectly conducting side walls; channel tilts and Prandtl number dependence. Good agreement between calculations and experiment is obtained for longitudinal convective roll velocities. The transverse velocities are found to be independent of Re.

1992-06-01

113

Growth and gas exchange response to water shortage of a maize crop on different soil types  

British Library Electronic Table of Contents (United Kingdom)

The effect of water shortage on growth and gas exchange of maize grown on sandy soil (SS) and clay soil was studied. The lower soil water content in the SS during vegetative growth stages did not affect plant height, above-ground biomass, and leaf area index (LAI). LAI reduction was observed on the SS during the reproductive stage due to early leaf senescence. Canopy and leaf gas exchanges, measured by eddy correlation technique and by a portable photosynthetic system, respectively, were affected by water stress and a greater reduction in net photosynthetic rate (A N) and stomatal conductance (g s) was observed on SS. Chlorophyll and carotenoids content was not affected by water shortage in either condition. Results support two main conclusions: (1) leaf photosynthetic capacity was unaffec...

2009-01-01

114

Geometry effects in the pulsed magnetization of high-temperature superconductor bulk parts  

International Nuclear Information System (INIS)

The dynamic response of cylindrical and ring-shaped YBaCuO bulk parts to pulsed magnetic fields is calculated by using small sets of finite elements. Some comparisons with experimental results are provided, and they give confidence in the modelling of the superconducting properties. Transient magnetizations as a function of time and space as well as shapes and absolute values of trapped magnetic flux profiles are presented. The influence of the sample geometry is investigated for different millisecond pulsed magnetization processes. Results are reported for different radial thicknesses and heights, different pulse durations, peak magnetic fields and pulse sequences with and without stepwise cooling. Comparisons concerning the achievable trapped magnetic field and flux are made, and implications for the use of high-temperature superconductor bulk parts as cryo-permanent magnets in potential applications like electric machinery are discussed.

2005-02-01

115

Experimental Investigation and RELAP5 Modeling of Two-Phase Flow in Horizontal Rectangular Channel  

British Library Electronic Table of Contents (United Kingdom)

The investigation of steam, water, and air flow characteristics in horizontal channel is a part of major investigations program at the Lithuanian Energy Institute. The objective of this program is to identify condensation effects on two-phase flow stability and to predict conditions when rapid condensation could be induced in two-phase condensable flow. This article presents investigation of steam-water and air multiphase flow in nearly horizontal rectangular channel. The experimental data for pressure drop and interfacial and wall shear stresses in the channel with uniform distribution of void fraction are presented in this paper. Overall channel dimensions are length = 1.2 m, width = 0.02 m, height = 0.1 m; however, the test section was about 0.84 m in length. Three different flow types ...

2011-01-01

116

Emissions and efficiency from production cooktop burners firing natural gas  

Energy Technology Data Exchange (ETDEWEB)

Investigations were conducted on the range of emission rates of NO, NO[sub 2], CO and hydrocarbons, and the thermal efficiencies produced by each burner on three production cookers, supplied by different Australian manufacturers. It was found that the emissions and efficiencies were markedly affected by (1) the thermal input, both with and without a load on the burner, and (2) the load-height to flame-length ratio, with a load on the burner. The effect of hydrocarbon leakage into the secondary/dilution air was investigated, to explain the observed correlation of hydrocarbon emission rate with dilution air flow. The hydrocarbons were found to arise from two sources: -leakage from the stabilisation ports at the base of the burner, which was found to be significant at the higher thermal input; -incomplete combustion of the fuel in the premix, which was the dominant source of hydrocarbons emissions at the lower thermal input. (author)

1994-12-01

117

Electrical properties of a calix[4]acid/amine Langmuir-Blodgett thin film  

British Library Electronic Table of Contents (United Kingdom)

In this work the DC and AC characteristics for metal-LB film-metal structures deposited by a standard Langmuir-Blodgett film deposition technique are investigated. The conduction mechanism has been studied for a thin film structure in which a calix[4]arene substituted with carboxylic acid groups has been deposited alternately with a calix[4]arene molecule substituted with amine groups. This LB film structure shows a typical insulating behaviour for low voltage values and the Schottky effect becomes dominant when the voltage increases. The conductivity at low voltage values was found to be 1.34x10^-^1^3Scm^-^1. The height of the potential barrier was determined to be 1.65eV for this alternate layer LB film system.

2011-01-01

118

Characterization of All-Chromium Tunnel Junctions and Single Electron Tunneling Devices Fabricated by Direct-Writing Multilayer Technique  

CERN Document Server

We report about the fabrication and analysis of the properties of Cr/CrO_x/Cr tunnel junctions and SET transistors, prepared by different variants of direct-writing multilayer technique. In all cases, the CrO_x tunnel barriers were formed in air under ambient conditions. From the experiments on single junctions, values for the effective barrier height and thickness were derived. For the Cr/CrO_x/Cr SET transistors we achieved minimal junction areas of 17 x 60 nm^2 using a scanning transmission electron microscope for the e-beam exposure on Si_3N_4 membrane substrate. We discuss the electrical performance of the transistor samples as well as their noise behavior.

1999-01-01

119

Body weight is a strong predictor of postural stability  

British Library Electronic Table of Contents (United Kingdom)

Proper balance control is a key aspect of acitivities of daily living. The aim of this study was to determine the contribution of body weight to predict balance stability. The balance stability of 59 male subjects with BMI ranging from 17.4 to 63.8kg/m2 was assessed using a force platform. The subjects were tested with and without vision. A stepwise multiple regression analysis was used to determine the independent effect of body weight, age, body height and foot length on balance stability (i.e., mean speed of the center of foot pressure). With vision, the stepwise multiple regression revealed that body weight accounted for 52% of the variance of balance stability. The addition of age contributed a further 3% to explain balance control. Without vision, body weight accounted for 54% of the...

2007-01-01

120

AlxGa1-xN/GaN multi-quantum-well ultraviolet detector based on p-i-n heterostructures  

British Library Electronic Table of Contents (United Kingdom)

We report on characterization of a set of AlGaN/GaN multiple-quantum-well (MQW) photodetectors. The model structure used in the calculation is the p-i-n heterojunction with 20 AlGaN/GaN MQW structures in i-region. The MQW structures have 2nm GaN quantum well width and 15nm AlxGa1-xN barrier width. The cutoff wavelength of the MQW photodetectors can be tuned by adjusting the well width and barrier height. Including the polarization field effects, on increasing Al mole fraction, the transition energy decreases, the total noise increases, and the responsivity has a red shift, and so the detectivity decreases and has a red shift.

2009-01-01

121

A study on the experimental verification for the pipe whip problem in a Nuclear Power Plant  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to investigate on the experimental verification analysis for the pipe whip problems and to obtain the quantitative evaluation technologies for the design technique of pipe whip restraints. These will contribute to the advance of nuclear regulatory technologies and enhance nuclear power plant safety. This study presents the experimental and transient analytical results of pipe whip tests using the 4', 6' diameter pipe and U-shaped restraints. In the tests, the effects of the overhang length, clearance, impact height on the pipe whip behavior of the pipe-restraints were investigated. The transient impact analysis of the pipe-restraint system was conducted by the finite element program ABAQUS. The applicability of the ABAQUS program to the pipe whip analysis is made clear through this analysis.

1993-12-15

122

The Influence of Weight and Height Status on Psychological Problems of Elementary Schoolchildren through Child Behavior Checklist Analysis  

UK PubMed Central (United Kingdom)

PurposeThis study aimed to evaluate weight and height status and their relationship with psychological problems among elementary schoolchildren.Materials and...Full Text Available

2009-06-30

123

Polymorphic Regions Affecting Human Height Also Control Stature in Cattle  

UK PubMed Central (United Kingdom)

Orthologous positions of 55 genes associated with height in four human populations were located on the bovine genome. Single nucleotide polymorphisms close to eight of these genes were significantly...Full Text Available

2011-03-01

124

Applications of BMI or BSI: Differences and Revisions According to Age and Height  

UK PubMed Central (United Kingdom)

Validation of body-mass relationships requires a careful statistical analysis of data of normal weight individuals. BMI (ratio between body mass and square of body height) and BSI values (ratio between...Full Text Available

2010-01-01

125

A TUNNEL DIODE UNIVIBRATOR AND PULSE HEIGHT DISCRIMINATOR  

Science.gov (United States)

A univibrator and a pulse height discriminator using tunnel diodes and backward diodes are described, along with their applications in pulse shaping and fast coincidence technique. The main advantages achieved are simplicity of design and speed. The characteristics of the two diodes are shown. (auth)

1961-03-01

126

Evaluation of Daytime Boundary Layer Heights from a ...  

Science.gov (United States)

... the vertical beam measures the movement of the ... be measured because the particle velocity in ... During precipitation, if the hydrometeor fall velocity is ...

2008-03-01

127

OMVPE growth of GaP and AlGaP using tertiarybutylphosphine as the phosphorus source  

Energy Technology Data Exchange (ETDEWEB)

GaP and AlGaP were grown by atmospheric pressure OMVPE on GaP substrates using tertiarybutylphosphine as the phosphorus source. A specular surface of GaP was obtained on a (100) just-oriented surface at 700deg C. Hazy but uniform thickness AlGaP was obtained. The growth efficiency for GaP was 1.2x10{sup 3}{mu}m/mol and that for AlGaP was 2.1x10{sup 3}{mu}m/mol.4.2 K photoluminescence showed near-edge emission from both GaP and AlGaP. (orig.).

1991-03-01

128

[Comparative study on the historical evolution of field surgery between China and Russia].  

Science.gov (United States)

Russian field surgery with its long history and distinctive characteristics has accumulated great experience in the long-time practice of warfare. Chinese field surgery was established and developed on the basis of studying from the Russian model, which opened up new areas of traffic medicine, molecular traumatology and assessment of biological effects on weapon destruction and carried out in-depth research on wound ballistics, blast injury, burns and combined injury etc. through decades of construction with continuous development and innovation, and a series of major achievements have been made in these fields. By making comparative study on the historical evolution, structure system, characteristics of campaigns and development of society between Chinese and Russian field surgery, it can be found that there are great gaps between them and we should strengthen the research for more rapid development. PMID:20510098

2010-03-01

129

Tin doping in spray pyrolysed indium sulfide thin films for solar cell applications  

British Library Electronic Table of Contents (United Kingdom)

This paper presents studies carried out on tin-doped indium sulfide films prepared using Chemical Spray Pyrolysis (CSP) technique. Effect of both in-situ and ex-situ doping were analyzed. Ex-situ doping was done by thermal diffusion, which was realized by annealing Sn/In2S3 bilayer films. In-situ doping was accomplished by introducing Sn into the spray solution by using SnCl45H2O. Interestingly, it was noted that by ex-situ doping, conductivity of the sample enhanced considerably without affecting any of the physical properties such as crystallinity or band gap. Analysis also showed that higher percentage of doping resulted in samples with low crystallinity and negative photosensitivity. In-situ doping resulted in amorphous films. In contrast to ex-situ doping, `in- situ doping' resulted i...

2010-01-01

130

Surge-line thermal stratification: Displacements and fatigue damage computations  

Energy Technology Data Exchange (ETDEWEB)

Slow, unexpected displacements have been experienced in most pressurized water reactor (PWR) surge lines. Sometimes, these displacement lead to gap closure at the pipe whip restraints. These movements occur because of thermal stratification. This movement has the potential to increase stresses to valves, which may exceed the material yield stress. To understand this phenomenon, Framatome, Commissariat a l'Energie Atomique, and Electricite de France have undertaken large programs for the study of (1) thermal-hydraulic tests with a half-scale Plexiglas surge line, (2) thermal-hydraulic computations of permanent states and transients with a two-dimensional model, and (3) mechanical analysis of displacements and computation of fatigue damage due to stratification. This paper deals with the last subject. Avoiding stratification in piping by process modifications is difficult because of the high flow rate needed. Alternative solutions for coping with ...

1989-01-01

131

Relationship between the electronic structure of passive films and the susceptibility to pitting corrosion of stainless steels; Relations entre la structure electronique des films de passivation formes sur les aciers inoxydables et la susceptibilite de ces derniers a la corrosion par piqures  

Energy Technology Data Exchange (ETDEWEB)

The passive films formed on 316L stainless steel in various NaCl solutions have been investigated by capacitance measurements (Mott-Schottky). Pitting parameters have been determined using the galvano-kinetic polarisation method. The obtained results reveal the existence of a shallow and a deep donor level localised in the band gap of the semiconducting oxide film. These energy levels are due to iron ions in the tetrahedral and octahedral positions. It also appears that the participation of the deep donor level effects the electric field. The study developed allows us to compare characteristic parameters of the electronic structure of the passive film to those related to pitting susceptibility. (authors) 25 refs.

1998-04-01

132

Production of scalar Higgs and pseudoscalar Higgs in multi-Higgs doublet models at {gamma}{gamma} colliders  

Energy Technology Data Exchange (ETDEWEB)

We present the effects of heavy CP-even (H) and CP-odd (A) Higgs bosons on the production cross section of the process {gamma}{gamma}{yields}tt at the energy around the mass poles of the Higgs bosons. It is found that interference between H and A with small mass gap, as well as the ones between Higgs bosons and continuum, contributes to the cross section, if the photon beams are polarized and if we observe the helicity of the top quarks. It is demonstrated in the framework of the minimal supersymmetric extension of the standard model that the H and A contributions can be sizable at future {gamma}{gamma} colliders for small values of tan {beta}. The methods to measure the CP-parity of the Higgs boson are also presented. The statistical significance of detecting the Higgs signals and measuring the Higgs CP-parity is evaluated. (orig.)

2000-05-01

133

Production of scalar Higgs and pseudoscalar Higgs in multi-Higgs doublet models at #gamma##gamma# colliders  

International Nuclear Information System (INIS)

We present the effects of heavy CP-even (H) and CP-odd (A) Higgs bosons on the production cross section of the process #gamma##gamma##->#tt at the energy around the mass poles of the Higgs bosons. It is found that interference between H and A with small mass gap, as well as the ones between Higgs bosons and continuum, contributes to the cross section, if the photon beams are polarized and if we observe the helicity of the top quarks. It is demonstrated in the framework of the minimal supersymmetric extension of the standard model that the H and A contributions can be sizable at future #gamma##gamma# colliders for small values of tan #beta#. The methods to measure the CP-parity of the Higgs boson are also presented. The statistical significance of detecting the Higgs signals and measuring the Higgs CP-parity is evaluated. (orig.)

2000-05-01

134

Multiple resonances and Coulomb blockade splitting in a quantum dot-DNA composite  

British Library Electronic Table of Contents (United Kingdom)

Inspired by the recent realizations of quantum dot (QD)-DNA conjugation, we study the spectral density of a magnetic impurity coupled to a mesoscopic semiconducting host. Using a combination of exact diagonalization technique and an analytic approach, we demonstrate that various types of resonances occur according to the relative position of impurity levels (IL) with respect to the host levels (HL). While the usual Coulomb peaks appear when the IL lie inside a band gap, with IL approaching HL and hybridization activated, they shift nonlinearly with the repulsion strength and even undergo splitting for a strong hybridization. When IL merge into HL, multiple resonances of a comblike structure are found along with a parity effect.

2011-01-01

135

High-temperature hysteretic electronic effects of (Al{sub x}Ga{sub 1{minus}x}){sub 0.5}In{sub 0.5}P (x > 0.65)  

Science.gov (United States)

The authors have studied (Al{sub x}Ga{sub 1{minus}x}){sub 0.5}In{sub 0.5}P doped with tellurium using deep level transient spectroscopy and associated electrical measurements. Several defect states are observed in the upper half of the band gap, that are believed to be intrinsic to the alloy system as well as related to the tellurium donors. Defects observed at measurement temperatures above 390 K exhibit a hysteretic behavior. The observed spectra depend on the biasing conditions applied to the Schottky diode during cooling. The hysteretic behavior suggests the existence of different defect configurations, which can be accessed under conditions of high temperatures and electrical stress, but remain stable below 300 K.

2000-02-01

136

High-temperature hysteretic electronic effects of (Al{sub x}Ga{sub 1{minus}x}){sub 0.5}In{sub 0.5}P (x > 0.65)  

Energy Technology Data Exchange (ETDEWEB)

The authors have studied (Al{sub x}Ga{sub 1{minus}x}){sub 0.5}In{sub 0.5}P doped with tellurium using deep level transient spectroscopy and associated electrical measurements. Several defect states are observed in the upper half of the band gap, that are believed to be intrinsic to the alloy system as well as related to the tellurium donors. Defects observed at measurement temperatures above 390 K exhibit a hysteretic behavior. The observed spectra depend on the biasing conditions applied to the Schottky diode during cooling. The hysteretic behavior suggests the existence of different defect configurations, which can be accessed under conditions of high temperatures and electrical stress, but remain stable below 300 K.

2000-02-01

137

Flavor Superconductivity & Superfluidity  

CERN Document Server

In these lecture notes we derive a generic holographic string theory realization of a p-wave superconductor and superfluid. For this purpose we also review basic D-brane physics, gauge/gravity methods at finite temperature, key concepts of superconductivity and recent progress in distinct realizations of holographic superconductors and superfluids. Then we focus on a D3/D7-brane construction yielding a superconducting or superfluid vector-condensate. The corresponding gauge theory is 3+1-dimensional N=2 supersymmetric Yang-Mills theory with SU(N) color and SU(2) flavor symmetry. It shows a second order phase transition to a phase in which a U(1) subgroup of the SU(2) symmetry is spontaneously broken and typical superconductivity signatures emerge, such as a conductivity (pseudo-)gap and the Meissner-Ochsenfeld effect. Condensates of this nature are comparable to those recently found experimentally in p-wave superconductors such as a ruthenate ...

2010-01-01

138

Fast neutron irradiation induced changes in the optical and thermal properties of modified polyvinyl chloride  

International Nuclear Information System (INIS)

The effect of both dopant and neutron radiation on the optical and thermal properties of polyvinyl chloride (PVC) has been studied. The doped samples with Pb and Cd were irradiated with a 14 MeV-neutron fluence in the range 7-28.8 x 10"9 n/cm"2. The optical energy gap E_o_p exhibits a significant dependence on the type of additive and the neutron irradiation fluence. The specific heat at constant pressure C_p showed a nonmonotonical change with radiation fluence. The results of this study show that PVC:Pb behaves as a crystalline structure which is only slightly affected by neutron irradiation, while PVC:Cd is highly affected. (author).

1994-11-01

139

Extended Conjugation in Polyaniline Like Structure Prepared by Plasma Polymerization Suitable for Optoelectronic Applications  

British Library Electronic Table of Contents (United Kingdom)

Plasma polymerization of aniline is carried out in a radiofrequency plasma reactor and the effect of polymerization time is examined in the structural, optical and optoelectronic properties of deposited films. Conjugated structures of polyaniline like films are obtained with unique and broad optical absorption band in the ultraviolet and entire visible region. The width of the absorption band increases and hence the optical band gap decreases with polymerization time. The optical constants are extracted by Swanepoel method and the optical dispersion parameters are determined by employing the Wemple-DiDomenico single oscillator model. The films exhibit similar thermal stability in air and argon atmosphere in the region of interest for optoelectronic applications. The photoluminescence study...

2011-01-01

140

Dynamic response analysis of pipe-restraints system. Analysis of pipe whip tests performed under PWR-LOCA conditions using 4-inch test pipe  

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of the dynamic response analysis of the pipe-restraints system by the general purpose finite element program ADINA. The analysis was carried out for the pipe whip tests performed under the PWR-LOCA conditions using 4-in. test pipe. In the analysis, the test pipe was modeled by an assemblage of the beam elements with the isotropic elastic-plastic material properties and the restraints were represented by the truss elements with the nonlinear elastic material properties including gap effect. The following results are obtained through the analysis. (1) Pipe can be modeled with the beam elements, when the overhang length is short and, therefore, the flattening of a cross-section of pipe is small. (2) The steady state restraint force can be predicted by modeling the restraints with the truss elements.

1983-09-01

141

Copper sulfates as cathode materials for Li batteries  

British Library Electronic Table of Contents (United Kingdom)

As lithium battery technology sets out to bridge the gap between portable electronics and the electrical automotive industry, cathode materials still stand as the bottleneck regarding performances. In the realm of highly attractive polyanion-type structures as high-voltage cathode materials, the sulfate group (SO4)^2^- possesses an acknowledged superiority over other contenders in terms of open circuit voltage arising from the inductive effect of strong covalent S-O bonds. In parallel, novel lithium insertion mechanisms are providing alternatives to traditional intercalation, enabling reversible multi-electron processes securing high capacities. Combining both of these advantageous features, we report here the successful electrochemical reactivity of copper sulfate pentahydrate (CuSO4.5H2O...

2011-01-01

142

High pressure waterjets for oil containment in calm and wavy waters; a parametric study  

International Nuclear Information System (INIS)

The use of high pressure waterjets (HPWJ) as oil barriers has been proposed and tested. It has been shown that a series of waterjets directed horizontally above the free water surface provide an effective means of containing or deflecting oil slicks. The waterjets generate a high speed air flow capable of moving the surface layer of the liquid. A numerical model is implemented to study the characteristics of the entrained turbulent air flow using the Spectral Element Method (SEM) and an algebraic turbulent model for the Reynolds stresses. A test of the code is done for turbulent Couette Flow to check the accuracy of the calculated shear stresses against published data. A parametric study is performed to evaluate the HPWJ system performance at various operating and design parameters which include manifold pressure, nozzle flow rate, nozzle characteristics, jet height and surface wave conditions. The total driving shear force and power required ...

1994-01-01

143

Effective Dynamics, Big Bounces and Scaling Symmetry in Bianchi Type I Loop Quantum Cosmology  

CERN Document Server

The detailed formulation for loop quantum cosmology (LQC) in the Bianchi I model with a scalar massless field has been constructed. In this paper, its effective dynamics is studied in two improved strategies for implementing the LQC discreteness corrections. Both schemes show that the big bang is replaced by the big bounces, which take place up to three times, once in each diagonal direction, when the area or volume scale factor approaches the critical values in the Planck regime measured by the reference of the scalar field momentum. These two strategies give different evolutions: In one scheme, the effective dynamics is independent of the choice of the finite sized cell prescribed to make Hamiltonian finite; in the other, the effective dynamics reacts to the macroscopic scales introduced by the boundary conditions. Both schemes reveal interesting symmetries of scaling, which are reminiscent of the relational ...

2007-01-01

144

An Undergraduate Course to Bridge the Gap between Textbooks and Scientific Research  

UK PubMed Central (United Kingdom)

This article reports on a one-semester Advanced Cell Biology course that endeavors to bridge the gap between gaining basic textbook knowledge about cell biology and learning to think and work as a researcher....Full Text Available

2011-03-01

146

A Failure of Coalition Leadership: The Falaise-Argentan Gap  

Science.gov (United States)

... failure at Goodwood and General Montgomery's continued failure to aggressively pursue the ground campaign. Air Chief ...

2002-04-09

147

Dynamic positive column in long-gap barrier discharges  

CERN Document Server

A simple analytical model of the barrier discharge in a long gap between opposing plane electrodes is developed. It is shown that the plasma density becomes uniform over large part of the gap in the course of the discharge development, so that one can speak of a formation of a dynamic positive column. The column completely controls the dynamics of the barrier discharge and determines such characteristics as the discharge current, discharge duration, light output, etc. Using the proposed model, all discharge parameters can be easily evaluated

2005-01-01

148

The effect of the Sep wind park near Oosterbierum, Friesland, The Netherlands, on birds. De invloed van de Sep-proefwindcentrale te Oosterbierum (Friesland) op vogels; Deel 3: Aanvlieggedrag overdag  

Energy Technology Data Exchange (ETDEWEB)

The study concerns 1984-1991. The wind park consists of 18 three-bladed 300 kW horizontal axis wind turbines of 35 meters height, and a rotor diameter of 30 meters, seven meteorological towers, and three cluster and control buildings. Aspects studied included disturbance of breeding, resting or feeding, and migrating birds, behavior of birds approaching the wind turbines during the day and night, and bird victims due to collision with the wind turbines and the meteorological towers. The flight behavior of birds approaching the wind park system during daylight is also dealt with. For at least a fifth of the observations it was noted whether the birds passing within 100 meters distance of a turbine showed a reaction or not. The proportion of the reactions was related to the wind park in operation or not in operation, and to the distance between the wind turbines, species, flight height, the passing distance, wind direction and wind force. ...

1992-01-01

149

Primary study on lesion mimic mutants of rice (oryza sativa L.)  

International Nuclear Information System (INIS)

Nineteen lesion mimic mutants (xsl1-19) of japonica rice Xiushui11 were obtained by ?-rays irradiation treatment. All mutants belonged to whole life lesion mimic. Lesion mimic of mutants didn't largen after tillering stage, leaves didn't wither, and no effect on the plants exsert spikes and seed. When the highest temperature in day exceeded 32 degree C in seedling stage, lesion mimic of all mutant expect xsl19 disappeared. Under 32 degree C, lesion mimic would appear gradually, and symptoms weren't inhibited by high temperature after 5 leaf stage. The plant heights of all lesion mimic mutants were 47.56-63.54 cm in the tillering stage, and that of CK was 83.75 cm; but the dwarf phenomenon of mutants only appeared before tillering stage, and didn't affect plant heights finally; the heading dates of mutants were the same to the CK, the ear length of all mutants were 9.43-15.19 cm, and that of CK was 16.41 cm; the total grain ...

2007-08-01

150

Ground-based remote sensing measurements of aerosol and ozone in an urban area: A case study of mixing height evolution and its effect on ground-level ozone concentrations  

International Nuclear Information System (INIS)

We have estimated the mixing height (MH) and investigated the relationship between vertical mixing and ground-level ozone concentrations in Seoul, Korea, by using three ground-based active remote sensing instruments operating side by side: micro-pulse lidar (MPL), differential absorption lidar (DIAL), and differential optical absorption spectroscopy (DOAS). The M H is estimated from MPL measurements of aerosol extinction profiles by the gradient method under convective conditions. Comparisons of the MHs estimated from MPL and radiosonde measurements show a good agreement (r"2 = 0.99). Continuous MPL measurements with high temporal and vertical resolution reveal the diurnal variations of the MH under convective conditions and the presence of a residual layer during the nighttime. Comprehensive measurements of ozone and aerosol by MPL, DIAL and DOAS during an high ozone episode (24-26 May 2000) in Seoul, Korea, reveal that (1) photochemical ozone production and ...

151

Equatorial scintillation model. Technical report, 1 February 1983-30 April 1985  

Energy Technology Data Exchange (ETDEWEB)

Radiowave scintillation in the presence of natural and/or high-altitude nuclear disturbances has the potential to disrupt numerous transionospheric radio and radar systems. This report develops a model characterizing the plasma-density irregularities that produce scintillation in the naturally disturbed equatorial F layer. The model is incorporated into Program WBMOD along with subroutines for computing both link geometry and scintillation indices, the latter by means of phase screen diffraction theory. The model is based on similarly extensive analysis of wideband data from two equatorial stations. It describes irregularities at an effective height of 350 km that are isotropic across the geomagnetic field and elongated by a factor of 50 along the field and whose one-dimensional spatial power spectrum obeys a single-regime power law with a (negative) spectral index of 1.5. The height-integrated spectral strength of the ...

1985-09-30

152

Development on the technologies for tritium removal processes  

Energy Technology Data Exchange (ETDEWEB)

While tritium exposure to the site-workers in Wolsung NPP is upto about 40 % of the total personnel exposure, Korea Institute of Nuclear Safety has asked tritium removal facility, as one of the requirements for post reactor construction, after operation of four CANDU reactors in Wolsung site. For the purpose of essential removal of tritium from the heavy water system of the heavy water reactors, an experiment of Ar-N{sub 2} cryogenic distillation tower was carried out as a preliminary study for development of liquid-phase catalytic exchange - cryogenic hydrogen distillation process. The steady-state reached after 50 minutes under 90 K in the Ar-N{sub 2} distillation column (inner diameter 20 mm, height 500 mm) packed with Dixon ring ({phi} 3 mm x H 3 mm), and the ratios of Ar-concentration at the top and at the bottom measured by gas chromatography within {+-}1 % relative error was approximately 93 : 3. This value was distillation performances quite higher than ...

1994-12-01

153

DYNAMICS OF SOLIDS IN THE MIDPLANE OF PROTOPLANETARY DISKS: IMPLICATIONS FOR PLANETESIMAL FORMATION  

International Nuclear Information System (INIS)

We present local two-dimensional and three-dimensional hybrid numerical simulations of particles and gas in the midplane of protoplanetary disks (PPDs) using the Athena code. The particles are coupled to gas aerodynamically, with particle-to-gas feedback included. Magnetorotational turbulence is ignored as an approximation for the dead zone of PPDs, and we ignore particle self-gravity to study the precursor of planetesimal formation. Our simulations include a wide size distribution of particles, ranging from strongly coupled particles with dimensionless stopping time #tau#_s #ident to# #OMEGA#t_s_t_o_p = 10"-"4 (where #OMEGA# is the orbital frequency, t_s_t_o_p is the particle friction time) to marginally coupled ones with #tau#_s = 1, and a wide range of solid abundances. Our main results are as follows. (1) Particles with #tau#_s #approx#> 10"-"2 actively participate in the streaming instability (SI), generate turbulence, and maintain the height of the ...

2010-10-20

154

A study of neutron room scattering at RPCF  

International Nuclear Information System (INIS)

High energy physics facilities must monitor the radiation doses received by their personnel. This monitoring can only be effective if the radiation detection devices can be calibrated with a good degree of accuracy. Radiation fields are usually composed of several types of radiation, including gamma rays, beta radiation, neutrons, etc. The neutron detection instruments respond not only to the neutrons coming directly from the source but also those scattered from the floor, walls, and ceiling. The amount of neutron scattering varies from site to site depending on the construction materials and layout of the building. The purpose of this study was to determine the scattered neutron fraction in the central volume of the calibration mezzanine of the Radiation Physics Calibration Facility (RPCF) at the Fermi National Accelerator Laboratory (Fermilab). At Fermilab, radiation workers dosimeters use CR39 for neutron detection, which are sent to an outside vendor for ...

1997-01-05

155

A study of neutron room scattering at RPCF  

Energy Technology Data Exchange (ETDEWEB)

High energy physics facilities must monitor the radiation doses received by their personnel. This monitoring can only be effective if the radiation detection devices can be calibrated with a good degree of accuracy. Radiation fields are usually composed of several types of radiation, including gamma rays, beta radiation, neutrons, etc. The neutron detection instruments respond not only to the neutrons coming directly from the source but also those scattered from the floor, walls, and ceiling. The amount of neutron scattering varies from site to site depending on the construction materials and layout of the building. The purpose of this study was to determine the scattered neutron fraction in the central volume of the calibration mezzanine of the Radiation Physics Calibration Facility (RPCF) at the Fermi National Accelerator Laboratory (Fermilab). At Fermilab, radiation workers dosimeters use CR39 for neutron detection, which are sent to an outside vendor for ...

1996-09-01

156

Development status of Severe Accident Analysis Code SAMPSON  

International Nuclear Information System (INIS)

The Four years of the IMPACT, 'Integrated Modular Plant Analysis and Computing Technology' project Phase 1 have been completed. The verification study of Severe Accident Analysis Code SAMPSON prototype developed in Phase 1 was conducted in two steps. First, each analysis module was run independently and analysis results were compared and verified against separate-effect test data with good results. Test data are as follows: CORA-13 (FZK) for the Core Heat-up Module; VI-3 of HI/VI Test (ORNL) for the FP Release from Fuel Module; KROTOS-37 (JRC-ISPRA) for the Molten Core Relocation Module; Water Spread Test (UCSB) for the Debris Spreading Model and Benard's Melting Test for Natural Convection Model in the Debris Cooling Module; Hydrogen Burning Test (NUPEC) for the Ex-Vessel Thermal Hydraulics Module; PREMIX, PM10 (FZK) for the Steam Explosion Module; and SWISS-2 (SNL) for the Debris-Concrete Interaction Module. Second, with the Simulation Supervisory System, up to ...

2000-11-01

157

Dependence of mobility on shallow localized gap states in single-crystal organic field-effect-transistors  

Energy Technology Data Exchange (ETDEWEB)

In order to optimize the performance of molecular organic electronic devices it is important to study the intermolecular density of states and charge transport mechanisms in the environment of crystalline organic material. Using this approach in Field Effect Transistors (FETs) we show that material purification improves carrier mobility and decreases density of the deep localized electronic state. We also report a general exponential energy dependence of the density of localized states in a vicinity of the mobility edge (Fermi energies up to approx7 times higher than the thermal energy (kT)) in a variety of the extensively purified molecular organic crystal FETs. This observation and the low activation energy of the order of approxkT suggest that molecular structural misplacements of the sizes that are comparable with thermal molecular modes rather than impurity deep traps play a role in formation of these shallow states. We find that the charge carrier mobility in ...

2009-12-15

158

A combinatorial library of micro-topographies and chemical compositions for tailored surface wettability  

Energy Technology Data Exchange (ETDEWEB)

Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X = 1 {mu}m and an intermediate inter-pillar gap size of Y = 4 {mu}m with superhydrophobic CAs over 170 . Surface analysis with X-ray photoelectron spectroscopy (XPS) revealed that CF{sub 3} groups ...

2011-06-15

159

Study of the effects of interactions quantum interference and disorder in GaAs and of GaAs jointed to a superconductor; Etude des effets d`interference quantique et de desordre dans GaAs avec interactions et GaAs connecte a un supraconducteur  

Energy Technology Data Exchange (ETDEWEB)

The aim of this thesis is to study the coherent transport in semiconducting-superconducting junctions. The SnPb-GaAs system has been studied. It has been shown that the behaviour of this junction is controlled by the disordered area induced by the annealing of the connection near the interface. For a few resistant junction, a conductance anomaly under the gap has been observed and has been explained by a mesoscopic effect in the limit of the very high disorders. The conductance of more resistant junctions has only been bound to the properties of the very disordered area of the semiconductor. The part of the electron-electron interactions on the phase coherence length and on the conductance has been studied. The evolving of the correction of the conductance due to interactions in magnetic field has been followed. The effect of the spin degeneration suppression in CdTe and the GaAs sign inversion in Shubnikov de Haas ...

1997-11-07

160

Electron and ion beam effects in amorphous SiO_2 and Si_3N_4 films for electronic devices  

International Nuclear Information System (INIS)

The effect of electron and ion beam irradiation on the Sisub(LVV) Auger spectra of SiO_2, Si_3N_4 and Si-oxynitride films was measured by the relative intensity of the 92 eV signal, characteristic for the formation of 'free' silicon during irradiation. While in Si-oxynitride the beam effects were almost negligible, some damage was found in Si_3N_4, but SiO_2 appeared to be extremely sensitive for electron and ion beam irradiation. By low energy electron loss spectroscopy of ion bombarded SiO_2 and Si_3N_4 films new electron states due to broken Si-O and Si-N bonds could be determined within the band gap of the insulators. The measured energy losses were interpreted by means of electron energy level schemes of the amorphous films. (author).

1982-01-01

161

Electron and ion beam effects in amorphous SiO/sub 2/ and Si/sub 3/N/sub 4/ films for electronic devices  

Energy Technology Data Exchange (ETDEWEB)

The effect of electron and ion beam irradiation on the Sisub(LVV) Auger spectra of SiO/sub 2/, Si/sub 3/N/sub 4/ and Si-oxynitride films was measured by the relative intensity of the 92 eV signal, characteristic for the formation of 'free' silicon during irradiation. While in Si-oxynitride the beam effects were almost negligible, some damage was found in Si/sub 3/N/sub 4/, but SiO/sub 2/ appeared to be extremely sensitive for electron and ion beam irradiation. By low energy electron loss spectroscopy of ion bombarded SiO/sub 2/ and Si/sub 3/N/sub 4/ films new electron states due to broken Si-O and Si-N bonds could be determined within the band gap of the insulators. The measured energy losses were interpreted by means of electron energy level schemes of the amorphous films.

1982-10-01

162

Ecotoxicology of Explosives  

Energy Technology Data Exchange (ETDEWEB)

Managing sites contaminated with munitions constituents is an international challenge. Although the choice of approach and the use of Ecological Risk Assessment (ERA) tools may vary from country to country, the assurance of quality and the direction of ecotoxicological research are universally recognized as shared concerns. Drawing on a multidisciplinary team of contributors, 'Ecotoxicology of Explosives' provides comprehensive and critical reviews available to date on fate, transport, and effects of explosives. The book delineates the state of the science of the ecotoxicology of explosives, past, present, and recently developed. It reviews the accessible fate and ecotoxicological data for energetic materials (EMs) and the methods for their development. The chapters characterize the fate of explosives in the environment, then provide information on their ecological effects in key environmental media, including aquatic, ...

2009-04-01

163

A study of the effect of rod-bowing on critical heat flux  

International Nuclear Information System (INIS)

An experimental study was carried out to determine the effect of rod-bowing on critical heat flux, using an electrically heated rod cluster. In this experiment, rod-bow was set to occur in the severest subchannel and axially at the middle between the last two spacers, with uniform axial heat flux. The maximum gap between the outer and inner rods was reduced variously to 1.6 mm, 1.00 mm and zero from the nominal value of 2.1 mm. Other experimental conditions were as follows: pressure 7 MPa; mass velocity 640-2600 kg/m"2sec; inlet subcooling 40-560 kJ/kg. Experimental results show only a slight rod-bowing effect, if any, compared with normal spacing, as confirmed by analysis of three-dimensional heat conduction around the rod-bowing area and by the local steam quality deviations calculated by subchannel analyses. (Auth.).

164

Surface Fermi level engineering: Or there's more to Schottky barriers than just making diodes and field effect transistor gates  

Science.gov (United States)

Surface scientists argue about the fundamental nature of Schottky barriers, or more precisely what determines the location of the Fermi level at semiconductor surfaces and interfaces. Electrical and materials engineers worry about how to make Schottky barrier diodes and gates to field effect transistors and the control of barrier heights. There is some interesting middle ground in which the location of the surface and interface Fermi level can, for example, determine semiconductor doping characteristics during crystal growth. The authors will discuss several interesting and well known examples of doping characteristics which are still somewhat mysterious. Specifically, they address the following question: (1) why is Ge doped GaAs p type when grown from Ga melts but n type when grown from Au melts (2) why is low resistivity p type ZnSe, AlAs, and AlGaInP hard to make, and more importantly, how can the problem be fixed. In addition they describe ...

165

Monitoring the Effect of Longwall Mining on Agricultural Environments - Interim Report  

Energy Technology Data Exchange (ETDEWEB)

The project was designed to quantify the impacts of longwall mine subsidence (LWMS) on the production and quality of agricultural vegetated environments. This project utilised a variety of traditional ground based sampling techniques including biomass harvests and estimates, leaf area index (LAI), pasture height, species composition and soil sampling along with proximal sensor data capture using a Crop Circle{trademark} and an EM38. Satellite imagery was collected using the Quickbird satellite and the high resolution imagery was used to monitor large areas of LWMS affected areas and adjacent un-mined land. Two landscapes were investigated using a whole of mine site technique including remote sensing, ground survey and traditional agricultural monitoring methods. The landscapes were at the Kestrel site in Emerald, QLD including a forage sorghum and an improved pasture and at Beltana in the Hunter Valley, NSW including an irrigated lucerne pasture and an unimproved ...

2009-06-15

166

Experimental study on the flow boiling heat transfer enhancement and pressure drop due to the bubble behavior restricted by a screen sheet; Kanaami ni yoru kiho kyodo seigen ni tomonau futtoryu dennetsu sokushin to ryudo sonshitsu ni kansuru jikkenteki kenkyu  

Energy Technology Data Exchange (ETDEWEB)

A unique method, previously proposed by the author, was applied to the heat transfer augmentation in the flow boiling field. In this method a screen sheet was put on the horizontal heated surface where bubble nucleation occurred. Generated vapor bubbles were trapped between the screen and the wall, became flat and moved along the surface. This restricted bubble behavior caused the heat transfer enhancement. Three types of the screen were tested in the present experiment and the effect of the screen was investigated on the heat transfer and two-phase flow characteristics. In two cases of them, the screen was displaced upward by the bubble nucleation. Compared with the ordinary flow boiling case, heat transfer was enhanced by a factor of 1.2 to 6 within the present experimental range. By using a simple flow model, it was made clear that the effect of the height of the displaced screen was important to evaluate the increase in ...

2000-03-25

167

Effect of site wind properties on wind-electric conversion costs  

Energy Technology Data Exchange (ETDEWEB)

The unit cost of energy production of wind generators is examined by means of a model of the turbine power curve and the Weibull model of wind probability function, by applying the usual economic equations. The analysis is carried out in terms of dimensionless variables whose range of variability is defined by examining the data of 80 modern commercial wind turbines; likewise, the economic parameters are based on the present state of costs. The unit cost decreases asymptotically when alpha (ratio between mean wind speed and cut-in speed) - increases and shows a lower limit of 2 to 5 Ecent/kWh. This cost depends both on the value of the machine parameter {phi} (ratio between nominal and cut-in speed) and on the basic prices. The effect of the Weibull shape parameter kappa is different according to the values of {alpha} and {phi}: with low {alpha} and high {phi} the unit cost increases along with {kappa} (that is with the regularity of the winds); the more {alpha} ...

2004-12-01

168

Water-level variations and their effects on tree growth and mortality and on the biogeochemical system at the phytoremediation demonstration site in Fort Worth, Texas, 1996-2003  

Science.gov (United States)

In 1996, a field-scale phytoremediation demonstration project was initiated and managed by the U.S. Air Force at a site in western Fort Worth, Texas, using a plantation of 1-year-old stems harvested from branches of eastern cottonwoods during the dormant season (whips) and a plantation of 1-year-old eastern cottonwood seedlings (calipers). The primary objective of the demonstration project was to determine the effectiveness of eastern cottonwoods at reducing the mass of dissolved trichloroethene transported within an alluvial aquifer. The U.S. Geological Survey conducted a study, in cooperation with the U.S. Air Force, to determine water-level variations and their effects on tree growth and mortality and on the biogeochemical system at the phytoremediation site. As part of the study, water-level and water-quality data were collected throughout the duration of the project. This report presents water-level variations at periodic sampling ...

2004-01-01

169

South Africa's experience in the synthetic fuels industry  

Energy Technology Data Exchange (ETDEWEB)

There are a number of factors favoring synfuel production in South Africa; (1) there are suitable coal fields in the immediate vicinity of our main industrial area.; (2) nature has given us relatively favorable geological conditions permitting highly mechanized extraction techniques so that coal can be delivered to the synfuel plants at Secunda at a cost - including return on capital - of less than $10.00 per ton, based on 1980 price levels; and (3) because the industry and its natural market are remote from the coast, it enjoys some transport protection against products refined from imported crude oil. Even more important we realized a long time ago that in trying to close the gap between the cost of synfuels and international oil prices, one is confronted with a moving target which can more effectively be attacked sooner rather than later. With such highly capital intensive projects, cash operating costs are relatively low. Product price ...

1981-04-01

170

Physical and electrochemical characterization of CdS hollow microspheres prepared by a novel template free solution phase method  

International Nuclear Information System (INIS)

Novel CdS hollow microspheres have been successfully synthesized via a facile template-free solution-phase reaction from cadmium nitrate and thioacetamide precursors. The morphology of CdS hollow microspheres depends strongly on the ratio between the precursors, cadmium nitrate to thioacetamide ratio. The physical properties of the hollow microspheres have systematically been studied by different characterization methods. The stoichiometry of the hollow microspheres studied by the energy dispersive X-ray diffraction spectroscopy confirmed that the synthesized CdS hollow microspheres are nearly stoichiometric bulk like CdS. The morphology of the hollow microspheres studied by high resolution scanning electron microscopy and transmission electron microscopy observations showed that the CdS hollow microspheres of the size of 2.5 ?m have hollow structure and are constructed by several nanoparticles of the size between 30 and 40 nm. The UV-visible diffuse reflectance spectroscopy studies ...

2010-12-15

171

Optical second-harmonic generation in III-V semiconductors: Detailed formulation and computational results  

Science.gov (United States)

In an earlier paper (Phys. Rev. Lett. 66, 41 (1991)), we calculated both the dielectric constant ({epsilon}{sub {infinity}}) and the nonlinear optical susceptibilities for second-harmonic generation ({chi}{sup (2)}) in the static limit for AlP, AlAs, GaP, and GaAs in the local-density approximation with and without a self-energy correction in the form of a scissors operator,'' including local-field effects. In this paper, we expand our presentation of this calculation. Agreement with experiment to within 15% for the nonlinear susceptibility is demonstrated where experiments are available (GaP and GaAs); the dielectric constants are in no worse than 4% agreement with experiment. The virtual hole'' contributions are reformulated to avoid large numerical cancellations in the case of near degeneracies. The virtual electron'' terms dominate over the virtual ...

1991-12-15

172

Flow regime transfer conditions for two-phase flow in a fracture  

Energy Technology Data Exchange (ETDEWEB)

Between 25 and 30 percent of total known petroleum reserves are contained within oil-laden fractured reservoirs where the dominant flow path is through the fractures. Economic oil recoveries from fractured reservoirs depend on a better understanding of the flow in fractures and networks of fractures. However, the flow of heavy oil and water, and particularly the flow regime map for two-phase immiscible flow has received less attention in contrast with gas-liquid flow in fractures. This paper discussed the use of flow pattern observations in a Hele-Shaw cell to generate two-phase flow regime maps. The paper investigated the effect of fracture gap and fluid viscosities on flow regimes. A correlation based on different flow and fracture properties was developed to define flow transition conditions between flow regimes. The paper presented the experiments, with particular reference to the experimental apparatus and the liquid-liquid system used in ...

2010-07-01

173

Electric-field-dependent electroreflectance spectra of visible-band-gap (InAlGa)P quantum-well structures  

Science.gov (United States)

We present results from the first studies of electric-field effects on optical transitions in visible-band-gap InGaP/InAlGaP multiple-quantum-well (MQW) structures. These structures, grown at 775 [degree]C by metalorganic vapor phase epitaxy on (100) GaAs substrates misoriented 6[degree] towards P(111)[r angle][l angle]111[r angle]A, consist of nominally undoped MQWs surrounded by doped In[sub 0.49]Al[sub 0.51]P cladding layers to form [ital p]-[ital i]-[ital n] diodes. The Stark shifts of various allowed and forbidden quantum-well transitions were observed in bias-dependent electroreflectance spectra of In[sub 0.49]Ga[sub 0.51]P/In[sub 0.49](Al[sub 0.5]Ga[sub 0.5])[sub 0.51]P MQW samples with 10-nm-thick layers. We find the magnitude of these shifts to depend on the details of the Mg doping profile, confirming the importance of Mg diffusion and unintentional background doping in these materials. Our results show that (InAlGa)P materials are ...

1994-04-04

174

Electric-field-dependent electroreflectance spectra of visible-band-gap (InAlGa)P quantum-well structures  

International Nuclear Information System (INIS)

We present results from the first studies of electric-field effects on optical transitions in visible-band-gap InGaP/InAlGaP multiple-quantum-well (MQW) structures. These structures, grown at 775 degree C by metalorganic vapor phase epitaxy on (100) GaAs substrates misoriented 6 degree towards P(111)right-angle left-angle 111 right-angle A, consist of nominally undoped MQWs surrounded by doped In_0_._4_9Al_0_._5_1P cladding layers to form p-i-n diodes. The Stark shifts of various allowed and forbidden quantum-well transitions were observed in bias-dependent electroreflectance spectra of In_0_._4_9Ga_0_._5_1P/In_0_._4_9(Al_0_._5Ga_0_._5)_0_._5_1P MQW samples with 10-nm-thick layers. We find the magnitude of these shifts to depend on the details of the Mg doping profile, confirming the importance of Mg diffusion and unintentional background doping in these materials. Our results show that (InAlGa)P materials are promising for visible-wavelength ...

175

The effects of surface damage on RF cavity operation  

Energy Technology Data Exchange (ETDEWEB)

We describe a model of damage in rf cavities and show how this damage can limit cavity operation. We first present a review of mechanisms that may or may not affect the ultimate fields that can be obtained in rf cavities, assuming that mechanical stress explains the triggers of rf breakdown events. We present a method of quantifying the surface damage caused by breakdown events in terms of the spectrum of field enhancement factors, Beta, for asperities on the surface. We then model an equilibrium that can develop between damage and conditioning effects, and show how this equilibrium can determine cavity performance and show experimental evidence for this mechanism. We define three functions that quantify damage, and explain how the parameters that determine this performance can be factored out and measured. We then show how this model can quantitatively explain the dependence of cavity performance on material, frequency, pulse length, gas, power supply and other ...

2006-04-14

176

The effect of type I migration on the formation of terrestrial planets in hot-Jupiter systems  

CERN Document Server

Context: Our previous models of a giant planet migrating through an inner protoplanet/planetesimal disk find that the giant shepherds a portion of the material it encounters into interior orbits, whilst scattering the rest into external orbits. Scattering tends to dominate, leaving behind abundant material that can accrete into terrestrial planets. Aims: We add to the possible realism of our model by simulating type I migration forces which cause an inward drift, and strong eccentricity and inclination damping of protoplanetary bodies. This extra dissipation might be expected to enhance shepherding at the expense of scattering, possibly modifying our previous conclusions. Methods: We employ an N-body code that is linked to a viscous gas disk algorithm capable of simulating: gas accretion onto the central star; gap formation in the vicinity of the giant planet; type II migration of the giant planet; type I migration of protoplanets; and the ...

2007-01-01

177

Practical operation of a trumpet secondary concentrator with a cavity receiver at elevated temperatures  

Energy Technology Data Exchange (ETDEWEB)

A prototype trumpet type nonimaging secondary concentrator was designed and fabricated for use with the Cummins Power Generation (CPG) 7.5 kW{sub e} dish-Stirling system. A set of operational tests was carried out with a high temperature heat pipe receiver and gas-gap calorimeter. These tests have successfully alleviated any operational concerns about the effectiveness of active water cooling for such devices. The authors obtained over two full days of testing with the cavity receiver operating at its design temperature of 660 C while the trumpet throat temperature remained {approx_equal} or less than 100 C. In addition, these tests have shown that the thermal isolation of the trumpet from the hot receiver is very effective. Highly variable insolation, instabilities in the temperature controller on the calorimeter, and a poor match between the optical quality of the primary and the design of the trumpet have made detailed ...

1997-12-31

178

Magnetic and chemical changes in marine sediments  

Energy Technology Data Exchange (ETDEWEB)

A considerable amount of chemical knowledge of marine sediments has been acquired in recent years but has not yet been utilized by paleomagnetists. On the other hand, geochemists are often unaware of the usefulness of numerous magnetic techniques. In this review we try to bridge this gap, and in particular, we outline many of the chemical and magnetic principles that should allow paleomagnetists to better identify and undertand chemical changes that affect the magnetic properties of marine sediments. The chemical principles include those for distinguishing the four major sources of sediments (continental, biological, authigenic/hydrogenous, volcanic/hydrothermal) from one another by determining elemental abundance distributions, as well as for investigating the stabilities of mineral phases relative to changes in pE and pH. The magnetic principles include the effects of authigenesis and diagenesis on magnetic properties, particularly on the ...

1980-05-01

179

Impact of oil and related chemicals on the marine environment  

International Nuclear Information System (INIS)

This review updates a previous review entitled ''Impact of Oil on the Marine Environment''. It covers oil and individual hydrocarbons, used lubricating oils, chemical control agents for oil spills, and wastes from offshore petroleum operations. It considers all major knowledge generated since the mid-1970s. The review covers its topics comprehensively, from a consideration of the composition, sources and inputs of oil to its ecological and human health effects and its effects on man's use of the sea. The review addresses several key questions on the present levels of contamination, the impact of hydrocarbons and related chemicals on marine biota, the recovery potential of marine ecosystems exposed to these contaminants, the degree of protection required for marine ecosystems known to be vulnerable and sensitive, and recommended research and other actions to fill gaps in knowledge. The review describes the hazards of marine ...

180

Heat transfer in parallel plate duct with a sinusoidal wave plate uniaxially inserted (1st). Effect of wave length on heat transfer augmentation  

Energy Technology Data Exchange (ETDEWEB)

High-performance heat transfer augmentation methods applicable in the forced convection field of heat exchangers include a method which requires no external drive means, such as the insertion of a turbulence augmentation object into the flow passage and the use of a wave-shaped flow passage, but disturbs the main stream of flow to raise the heat transportation effect thereby to augment heat transfer in the flow passage. The heat transfer characteristics and thermal performance ratio achieved when sinusoidal-shape plates are inserted instead of augmentation objects, such as cylinders, with a high shape-induced resistance were studied. As a result, the relationship between the resistance coefficient, average Nusselt number, heat transfer coefficient, and pitch was clarified. It has been revealed that the use of eddies with a large gap flow and recirculation area should be considered in order to get a higher heat transfer coefficient and a higher ...

1988-09-01

181

Analysis of the roles of E6 binding to E6TP1 and nuclear localization in the human papillomavirus type 31 life cycle  

British Library Electronic Table of Contents (United Kingdom)

The E6 oncoproteins of high-risk human papillomaviruses provide important functions not only for malignant transformation but also in the productive viral life cycle. E6 proteins have been shown to bind to a number of cellular factors, but only a limited number of analyses have investigated the effects of these interactions on the viral life cycle. In this study, we investigated the consequences of HPV 31 E6 binding to E6TP1, a putative Rap1 GAP protein. HPV 16 E6 has been shown to bind as well as induce the rapid turnover of E6TP1, and similar effects were observed with HPV 31 E6. Mutation of amino acid 128 in HPV 31 E6 was found to abrogate the ability to bind and degrade E6TP1 but did not alter binding to another ?-helical domain protein, E6AP. When HPV 31 genomes containing mutations a...

2007-01-01

182

Non-standard natural circulation in primary circuit of VVR-440, behavior of horizontal steam generator in this regime  

Energy Technology Data Exchange (ETDEWEB)

Analyzing various SBLOCA with high pressure safety injection (HPSI) at VVER-440/213, we met a surprising phenomenon - a 'natural' circulation post SG heat transfer reversal. This is not usual, because normal natural circulation (NC) in primary circuit is connected with positive heat transfer at SG. If there is reverse heat transfer at SG (as soon as the break enthalpy outflow is sufficient for removal of reactor decay heat), it should obstruct any natural circulation. The question was, what is the driving force of this 'non-standard natural circulation'. After all we revealed that force - it is the density difference between the colder water in reactor downcomer (cold water from HPSI) and warmer water in inner reactor (lower plenum, core, upper plenum). This phenomenon could be confusing for operating personal, because there would be an opposite temperature difference at the loop than by normal natural circulation (under non-standard NC conditions ...

2001-07-01

183

Non-standard natural circulation in primary circuit of VVR-440, behavior of horizontal steam generator in this regime  

International Nuclear Information System (INIS)

Analyzing various SBLOCA with high pressure safety injection (HPSI) at VVER-440/213, we met a surprising phenomenon - a 'natural' circulation post SG heat transfer reversal. This is not usual, because normal natural circulation (NC) in primary circuit is connected with positive heat transfer at SG. If there is reverse heat transfer at SG (as soon as the break enthalpy outflow is sufficient for removal of reactor decay heat), it should obstruct any natural circulation. The question was, what is the driving force of this 'non-standard natural circulation'. After all we revealed that force - it is the density difference between the colder water in reactor downcomer (cold water from HPSI) and warmer water in inner reactor (lower plenum, core, upper plenum). This phenomenon could be confusing for operating personal, because there would be an opposite temperature difference at the loop than by normal natural circulation (under non-standard NC conditions water is heated in SG so there is ...

2001-03-20

184

Chemical and Biological Warfare: A Manageable Problem  

Science.gov (United States)

... On 20 March 1995, members from the religious cult Aum Shinrikyo released sarin and VX nerve gas into the Tokyo subway system. At the height of ...

2003-01-27

185

A New Stem Taper Function for Short-rotation poplar  

Energy Technology Data Exchange (ETDEWEB)

A new stem taper function was established for individual trees of two poplar hybrid clones grown on a short-rotation coppice. The model could be easily fitted and required three parameters to be estimated. It can be used to estimate both diameter at a given height and height for a given top diameter. Two of the three parameters controlled the conical and the neiloid parts of the stem. Significant differences in these parameters were observed between the two clones even if no differences were observed for diameter at breast height or total height of the stem. The model could not be integrated to calculate volumes (total volume, merchantable volume), which were estimated by numerical integration. However, use of this new model allows the optimal length of billets to be determined and thus maximizes the merchantable biomass of poplar in short-rotation coppice by minimizing the biomass of residues.

2003-07-01

186

2010 NASA Terrestrial Ecology Science Team Meeting - NASA Carbon ...  

Science.gov (United States)

The biomass maps were compared with the U.S. Forest Service biomass map for 2002 , LVIS height data, and estimates from high resolution imagery. ...

187

Unsteady state heat transfer in the vertical walls of a building  

Energy Technology Data Exchange (ETDEWEB)

The unsteady state heat transfer behaviour of a vertical wall subject to the effects of uniform radiation is investigated and the dimensional analysis of combined heat transfers by conduction, convection and radiation is presented. The convective heat transfer coefficients used in the numerical model are determined experimentally by means of an assembly resembling the conditions encountered in the dwelling (variable temperatures and heat flows in time and space, wall associated with a floor, radiative flux outside the wall). In routine conditions (homogeneous wall dimensions, temperature differentials less than 40/sup 0/C), it is shown that the problem depends in practice on three parameters (instead of five) and that nomographs can give the energy accumulated in the wall as a function of its geometric and thermal charactersitics and the external conditions (type and thickness of material, changes in incident flux, convection over the height of ...

1982-12-01

188

Treatment of Difficult Wastes with Molten Salt Oxidation  

Energy Technology Data Exchange (ETDEWEB)

Molten salt oxidation (MSO) is a good alternative to incineration for the treatment of a variety of organic wastes such as explosives, low-level mixed waste streams, PCB contaminated oils, spent resins and carbon. Since mid-1990s, the U.S. Army Defense Ammunition Center (DAC) and the Department of Energy (DOE) have jointly invested in MSO development at the Lawrence Livermore National Laboratory (LLNL). LLNL first demonstrated the MSO process for the effective destruction of explosives, explosives-contaminated materials, and other wastes on a 1.5-kg/hr bench-scale unit, and then in an integrated MSO facility capable of treating 8 kg/hr of low-level radioactive mixed wastes. Several MSO systems have been built with sizes up to 10 ft in height and 16 inches in diameter. LLNL in 2001 completed a MSO plant for DAC for the destruction of explosives-contaminated sludge and explosives-contaminated carbon. We will present in this paper our latest ...

2003-02-21

189

Thermal effect on superhydrophobic performance of stearic acid modified ZnO nanotowers  

Energy Technology Data Exchange (ETDEWEB)

The thermal desorption of stearic acid on superhydrophobic zinc oxide nanotowers has been investigated. The stearic acid passivated zinc oxide nanotowers provide a very high contact angle of {approx}173 {+-} 1.1 deg. with a very low hysteresis of {approx}1.4 {+-} 0.5 deg. due to the presence of a binary structure composed of several nanosteps on each nanotower of height {approx}700 nm that eventually reduces the area of contact between the drop and the nanotowers and trapping more air as revealed by the field emission scanning electron microscopy images. The superhydrophobic performance of these nanotowers, however, declines following annealing at elevated temperatures. Fourier transform infrared spectra show a reduction in the intensity of stearic acid -CH{sub n} peaks at elevated temperatures revealing the cause of the decrease in contact angle and confirming the occurrence of thermal desorption at 184 deg. C. The corresponding activation energy for desorption ...

2008-02-28

190

Study of passive films formed on stainless steel surfaces, using Auger spectroscopy  

International Nuclear Information System (INIS)

This paper deals with the characterization of passive films formed on stainless steel (26% Cr and 0 to 3%Mo). The influence of the applied passivation potential and the effect of molybdenum additions to steel upon the composition profiles of passive films formed in an aqueous NaCl solution (3.5% at pH 2.5) are studied. The technique involved is Auger electron spectroscopy combined with ion sputtering. Some electrochemical techniques have been used in conjunction. A quantitative approach of the Auger spectra during the progressive removal of the passive film is described. The peak-to-peak height of the Auger lines are treated in order to yield the atomic fraction of the various elements present in a given subsurface layer. The analytical study of the film by electron spectroscopy indicates that molybdenum plays a part at the metal-oxide interface where this element acts on the chromium diffusion process. This phenomenon, which depends on the ...

1975-01-01

191

Rooting of hybrid clones of Populus tremula L. x P. tremuloides Michx. by stem cuttings derived from micropropagated plants  

Energy Technology Data Exchange (ETDEWEB)

Propagation costs could be cut by replacing part of the micropropagation process with steps involving more traditional techniques. This study explored possibilities for improving existing vegetative propagation techniques for aspen using stem cuttings obtained from micropropagated plants. Vegetative propagation through stem cuttings was studied in 10 micropropagated hybrid aspen clones (Populus tremula L. x P. tremuloides Michx). Cuttings containing one axillary bud were harvested from the same donor plants twice during the growing season: the first harvest in May and the second harvest in July. Rooting percentage was correlated positively with root length, number of roots and height of cutting plant but negatively with length of rooting. The average rooting percentage was 53% in the first harvest and 27% in second harvest. Indole-3-butyric acid treatments (1.2 mM) significantly improved rooting in the second harvest, but not in the first harvest, suggesting ...

2001-07-01

192

Photoconductive ultraviolet detectors based on ZnO films  

Energy Technology Data Exchange (ETDEWEB)

Properties of photoconductive ultraviolet detectors fabricated on ZnO films were presented. Highly c-axis oriented ZnO films were grown on glass substrates by pulsed laser deposition. Ultraviolet photodetectors were fabricated based on metal-semiconductor-metal planar structures. The photoresponsivity and the quantum efficiency are much higher in the ultraviolet range than in the visible range, and the peak values are around 360 nm. Photocurrent transients show that the detector has a large photocurrent with the peak value of 2.8 mA, and a slow photoresponse with a rise time of 5 min and a decay time of 7 min. The response curve of the detector is fitted well with exponential curve. The large photocurrent should result from the both effects of the accumulation of conduction electrons and the decrease of the barrier height between crystallites. The relaxation time constant {tau} obtained from the curve fitting represents the time accumulation ...

2006-12-15

193

Photoconductive ultraviolet detectors based on ZnO films  

International Nuclear Information System (INIS)

Properties of photoconductive ultraviolet detectors fabricated on ZnO films were presented. Highly c-axis oriented ZnO films were grown on glass substrates by pulsed laser deposition. Ultraviolet photodetectors were fabricated based on metal-semiconductor-metal planar structures. The photoresponsivity and the quantum efficiency are much higher in the ultraviolet range than in the visible range, and the peak values are around 360 nm. Photocurrent transients show that the detector has a large photocurrent with the peak value of 2.8 mA, and a slow photoresponse with a rise time of 5 min and a decay time of 7 min. The response curve of the detector is fitted well with exponential curve. The large photocurrent should result from the both effects of the accumulation of conduction electrons and the decrease of the barrier height between crystallites. The relaxation time constant #tau# obtained from the curve fitting represents the time accumulation ...

2006-12-15

194

Microcephaly  

International Nuclear Information System (INIS)

Among in uterus exposed A-bomb survivors, fetal week is the most important factor to clarify the effects of A-bomb radiation on developmental process of the fetal brain. The study population of in utero exposed A-bomb survivors has first been established in 1953 in Hiroshima and in 1955 in Nagasaki. According to the estimated DS86 uterus absorption doses, fetal absorption doses obtained from the uterus doses, and intelligence quotient. Various studies on brain damage, including microcephaly, have been undertaken among in uterus exposed A-bomb survivors. Brain development has been shown to be affected during the fetal weeks 8-15 and 16-25. A review of the literature has revealed that 80% of the children with mental retardation and 15 of 18 cases of microcephaly (83%) were exposed in utero during the fetal week 8-15. Among children exposed at the fetal weeks 8-15 and 16-25, average learning was significantly decreased. The incidence of spasm was highest among ...

195

Medium term evaluation of meteorological conditions, power performance and loads on the first Swedish offshore wind farm at Bockstigen  

Energy Technology Data Exchange (ETDEWEB)

The first offshore wind farm in Sweden; Bockstigen, consists of five 500 kW stall controlled wind turbines on mono pile foundations. The main objectives of the technical evaluation are to verify the original design assumptions made for a load carrying mono pile and bedrock, investigate offshore power production versus onshore ditto as well as to determine park effects and analyse meteorological multi-mast statistics which serve as reference data to a newly developed computer code for offshore wind energy potential mapping. The 'main' measurement system has continuously been acquiring data at 1 and 20 Hz/channel since the summer of 1998. A 40 m meteorological mast was built within the wind farm in the summer of 1999 in order to acquire relatively undisturbed wind speed data from 'free' sectors as well as to enable wake measurements. The mono pile and tower of one of the turbines are equipped with strain gauges at several depths ...

2001-12-01

196

Influence of fly ash on soil physical properties and turfgrass establishment  

Energy Technology Data Exchange (ETDEWEB)

A field study (1993-96) assessed the benefits of applying unusually high rates of coal fly ash from power plants as a soil amendment to enhance water retention of soils without adversely affecting growth and marketability of the turf species, centipedegrass (Eremochloa ophiuroides (Munro) Hack.) A Latin Square plot design was employed that included 0 (control, no fly ash applied), 280, 560 and 1120 MgHa {sup -1} application rates of unweathered precipitator fly ash. The fly ash was spread evenly over each plot area, rototilled, and allowed to weather under natural conditions for 8 months before seeding. High levels of soluble salts, indicated by the electrical conductivity of soil extracts, in tandem with an apparent phytotoxic effect from boron, apparently inhibited initial plant establishment as shown by substantially lower germination counts in treated soil. However, plant height and rooting depth were not adversely affected, as were the dry ...

2001-04-01

197

Hydrogen-related surface modifications of 20 nm thin straight-sided niobium nano-wires and niobium meander-films  

Energy Technology Data Exchange (ETDEWEB)

Nano-wire arrays of Niobium were produced by small angle sputtering on facetted sapphire, using the self shadowing effect of the facets. A wire width of about 80 nm was adjusted, the mean (maximum) wire height was about 20 nm (30 nm), the length can be in the cm range. Meander-film morphologies of 20 nm mean (26 nm maximum) thickness were produced by conventional sputtering onto smooth sapphire substrates at elevated temperatures. The morphology of the wires was investigated with atomic force microscopy (AFM), using contact mode. Meander-films were studied by scanning tunnelling microscopy (STM). Hydrogen loading was performed by instantaneously increasing the hydrogen gas pressure above the solubility limit. Thus, an elongated hydride could be monitored in an about 30 nm thick wire. STM studies on meander-films show the presence of cylindrical hydrides. Local out-of-plane and in-plane expansion can be explained by the formation of hydrides, ...

2007-10-31

198

Heat transfer augmentation in a heat exchanger tube using a baffle  

International Nuclear Information System (INIS)

Heat transfer enhancement in a heat exchanger tube by installing a baffle is reported. The effect of baffle size and orientation on the heat transfer enhancement was studied in detail. Three different baffle arrangements were considered. The results show that for the vertical baffle, an increase in the baffle height causes a substantial increase in the Nusselt number but the pressure loss is also very significant. For the inclined baffles, the results show that the Nusselt number enhancement is almost independent of the baffle inclination angle, with the maximum and average Nusselt number 120% and 70% higher than that for the case of no baffle, respectively. For a given baffle geometry, the Nusselt number enhancement is increased by more than a factor of two as the Reynolds number decreased from 20,000 to 5000. Simulations were conducted by introducing another baffle to enhance heat transfer. The results show that the average Nusselt number for ...

2007-04-01

199

Device for removing drilling fines from a well head  

Energy Technology Data Exchange (ETDEWEB)

The device for removing drilling fines from the well head includes a support disk encompassing the sucker rod of the drilling machine with frame made in the form of a dish with inner conical surface, and overturned truncated cone located in the dish of the support disk with the formation between them of a ring guide slit. In order to improve the effectiveness of removing the drilling fines and convenience of operation by excluding heavy manual auxiliary operations to clean the well head and to move the device from one well to another, it is equipped with a mechanism for suspension with a drive. The inner conical surface of the dish is equipped with slide blocks, while the overturned truncated cone is equipped with projections. The suspension mechanism is made in the form of a hydrocylinder and two pairs of levers connected in pairs by means of hinges. The hinges of each pair of levers are connected to the hydrocylinder, and the levers are hinged to the machine ...

1982-01-01

200

Correlation between ion beam parameters and physical characteristics of nanostructures fabricated by focused ion beam  

International Nuclear Information System (INIS)

We report a study of the physical characteristics of the pillars of C, Pt and W grown by 10-30 keV Ga focused ion beam (FIB) as a function of Ga ion flux, and present a quantitative analysis of the elements using energy-dispersive analysis of X-rays (EDAX). All the FIB grown pillars exhibit a rough morphology with whisker like protrusions on the cylindrical surface and broadening of the base as compared to the nominal size. For a constant fluence, the height of the pillar initially increases and then reduces after going through a maximum as a function of ion flux in all the cases. The compositional analysis shows good metallic quality for Pt structures but reveals significant contamination of Ga in C and Ga and C in W structures at higher ion fluxes. Explanation to all these observations has been sought in the light of secondary ion and electron effects and the different processes involved which lead to the FIB induced deposition.

2008-04-01

201

Comparison of Measured and Predicted {sup 3}H Concentrations in Environmental Media around the Wolsung Site for the Validation of INDAC Code  

Energy Technology Data Exchange (ETDEWEB)

The predicted results of INDAC code were compared with measured {sup 3}H concentrations in air and pine-needle around the Wolsung site. The optimal sets of input data to INDAC were in addition selected by comparing the measured values with the predicted values of INDAC based on various conditions such as the release modes of effluents into the environment, the classification of wind classes, and the consideration of terrain. The predicted {sup 3}H concentrations in air and pine-needle were shown to have good agreement with measured values, although there are some limitations such as uncertainties in measured values, complex topology around the site, and the land-sea breeze effects. The assumption on the {sup 3}H behavior in vegetables or plants that the ratio of {sup 3}H concentration in plant water to {sup 3}H concentration in atmospheric water is 1/2 was shown to be conservative in terms of the audit calculation performed by the regulator. It was also found that ...

2000-06-15

202

Comparison of Measured and Predicted "3H Concentrations in Environmental Media around the Wolsung Site for the Validation of INDAC Code  

International Nuclear Information System (INIS)

The predicted results of INDAC code were compared with measured "3H concentrations in air and pine-needle around the Wolsung site. The optimal sets of input data to INDAC were in addition selected by comparing the measured values with the predicted values of INDAC based on various conditions such as the release modes of effluents into the environment, the classification of wind classes, and the consideration of terrain. The predicted "3H concentrations in air and pine-needle were shown to have good agreement with measured values, although there are some limitations such as uncertainties in measured values, complex topology around the site, and the land-sea breeze effects. The assumption on the "3H behavior in vegetables or plants that the ratio of "3H concentration in plant water to "3H concentration in atmospheric water is 1/2 was shown to be conservative in terms of the audit calculation performed by the regulator. It was also found that data sets based on mixed ...

2000-06-01

203

Calculation of ventilation efficiency and of load situations for load-relieving air conduction systems; Berechnung der Lueftungseffektivitaet und der Belastungssituation fuer lastmindernde Luftfuehrungen  

Energy Technology Data Exchange (ETDEWEB)

Zone modeling permits taking account of the effect of load-relieving air conduction systems in the planning of HVAC plants. Although this only supplies average values for the degree of load and height of the fresh air layer rather than a detailed description of concentration and temperature distributions in the room, it is quite sufficient for the planning of load-relieving air conduction systems. Moreover, the cost of zone modeling in the planning of HVAC plants remains within reasonable limits. Upscale planning, instruments can thus be reserved for more exacting problems. (orig.) [Deutsch] Zonenmodelle erlauben die Wirkung lastmindernder Luftfuehrungen bei der Planung von RLT-Anlagen zu beruecksichtigen. Sie liefern zwar nur Mittelwerte fuer den Belastungsgrad und die Hoehe der Zuluftschicht und keine detaillierte Konzentrations- und Temperaturverteilungen im Raum. Diese Werte reichen jedoch fuer die Planung lastmindernder ...

1994-12-31

204

Blast designs to improve dragline stripping rates. Final report: Phase I  

International Nuclear Information System (INIS)

This report is in accordance with Phase I of the United States Department of Energy and Bureau of Mines Contract No. USDOE DE-AC01-77QQ90147. A thorough literature search was conducted and the current mining practice at nine coal stripping operations reviewed in detail. A review of the state of the art of blast design using current theory and practice is presented. Based upon this information, a series of recommendations are presented and a detailed test program is outlined for three operations. The recommendations to increase dragline productivity by improved blast design are directed at filling the bucket more quickly, with greater consistency and with a better fill factor: (a) overburden fragmentation, (b) muckpile displacements, and (c) blasting reliability. Recommended blast design concepts and operating procedures to provide the desired blast performance include: (1) Increase energy input per BCY by 40 to 100 percent and improve the effective powder ...

205

Binary pseudo-random gratings and arrays for calibration of the modulation transfer function of surface profilometers: recent developments  

Energy Technology Data Exchange (ETDEWEB)

The major problem of measurement of a power spectral density (PSD) distribution of the surface heights with surface profilometers arises due to the unknown Modulation Transfer Function (MTF) of the instruments. The MTF tends to distort the PSD at higher spatial frequencies. It has been suggested [Proc. SPIE 7077-7, (2007), Opt. Eng. 47 (7), 073602-1-5 (2008)] that the instrumental MTF of a surface profiler can be precisely measured using standard test surfaces based on binary pseudo-random (BPR) patterns. In the cited work, a one dimensional (1D) realization of the suggested method based on use of BPR gratings has been demonstrated. Here, we present recent achievements made in fabricating and using two-dimensional (2D) BPR arrays that allow for a direct 2D calibration of the instrumental MTF. The 2D BPRAs were used as standard test surfaces for 2D MTF calibration of the MicromapTM-570 interferometric microscope with all available objectives. The ...

2009-07-07

206

Augmented heat transfer in a rectangular duct with angled ribs  

Energy Technology Data Exchange (ETDEWEB)

Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass transfer coefficients. Downwash of the rotating secondary flow, reattachment of ...

1998-04-01

207

A calculation model for thermo-hydraulic analyses of the PGV-1000 steam generator  

International Nuclear Information System (INIS)

A calculation model was developed for the analysis of thermal and hydraulic processes in the PGV-1000 horizontal steam generator. The model makes it possible to examine the hydraulics of the primary medium, i.e., the distribution of flow velocities and mass flows in the exchanger tube system and hydraulic losses of the primary medium in the steam generator during its flow between the two connecting sites to the main circulation pipeline, spatial distribution of heat fluxes between the primary and secondary sides of the steam generator and the total transmitted thermal power, pressure on the secondary side of the generator, natural circulation of the working medium on the secondary side, and the mean circulation number, spatial distribution of the volume fraction of the steam component in the intertubular space, effect of the perforated sheet on the thermo-hydraulic processes in the steam generator, redistribution of the steam component in the compartment above the ...

1994-01-01

208

Large eddy simulation based fire modeling applications for Indian nuclear power plant  

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: The Nuclear Power Plants (NPPs) are always designed for the highest level of safety against postulated accidents which may be initiated due to internal or external causes. One of the external/internal causes, which may lead to accident in the reactor and its associated systems, is fire in certain vital areas of the plant. Conventionally, the fire containment approach and/or the fire confinement approach is used in designing the fire protection systems of NPPs. Indian NPPs (PHWRs) follow the combined approach to ensure plant safety and all newly designed plants are required to comply with the provisions of Atomic Energy Regulatory Board (AERB) fire safety Guide. In respect of older plants, the reassessment of adequacy of fire safety provisions in the light of current advances has becomes essential so as to decide upon the steps for retrofitting. Keeping this in mind the deterministic fire hazard analysis was carried out for the Madras Atomic Power ...

2005-07-01

209

Laboratory tests on the effects of partial embedment on soil-structure interaction (embedment effect test on soil-structure interaction)  

International Nuclear Information System (INIS)

A series of Model Tests of Embedment Effect on Reactor Buildings has been carried out by the Nuclear Power Engineering Corporation (NUPEC), under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan. Reactor buildings in Japan are partially embedded in general. Therefore, it is important to know how partial embedment affects the vibration characteristics of reactor buildings relating to seismic safety. Laboratory tests were conducted using a ground model made of silicone rubber (Young's modulus 2.3x10"6 Pa, Poisson's ratio 0.484, Density 1.24x 10"3 kg/m3 , Damping ratio 0.01) and a foundation model made of aluminum shown to study the effects of embedment on soil-structure interaction with different backfill types. The ground model is a cylinder, 70 cm high and 300 cm in diameter, with pit where the parallelepiped foundation model with square plan of 30 cm x 30 cm and 18 cm high was placed. Four types of backfill ...

1993-08-15

210

Thermal-hydraulic characteristics of boiling water two-phase flow in narrow horizontal rectangular channel  

International Nuclear Information System (INIS)

Heat transfer and flow characteristics of water boiling flow were experimentally investigated in narrow horizontal rectangular channels with the gaps of 0.6mm-2.03mm. The heat transfer of two-phase boiling flow was weakend in smaller gap. The two-phase friction pressure drop decreased with the gap size and the two-phase friction multipliers were smaller compared with those in normal channels. Correlations to predict te boiling heat transfer coefficients were obtained. (author)

2003-05-28

211

New method for determining the energy gap of a superconductor using the maximum in differential conductance of the electron tunneling spectrum  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a new method for the determination of the energy gap of superconductors. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. The maximum voltage in differential conductance V/sub max/ was measured from the electron tunneling spectrum. From V/sub max//kT and the curve, one can easily calculate the energy gap value ..delta... This method is simple, and the accuracy almost approaches that of the curve-fitting method.

1986-07-01

212

New method for determining the energy gap of a superconductor using the maximum in differential conductance of the electron tunneling spectrum  

International Nuclear Information System (INIS)

This paper presents a new method for the determination of the energy gap of superconductors. The V/sub max//kT versus #DELTA#/kT curve was calculated from tunneling theory. The maximum voltage in differential conductance V/sub max/ was measured from the electron tunneling spectrum. From V/sub max//kT and the curve, one can easily calculate the energy gap value #DELTA#. This method is simple, and the accuracy almost approaches that of the curve-fitting method.

213

New method for determining the energy gap of a superconductor using the maximum in differential conductance of electron tunneling spectrum  

Energy Technology Data Exchange (ETDEWEB)

A new method for determining the energy gap of a superconductor using the maximum in the differential conductance curve of electron tunneling spectrum is given in this paper. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. V/sub max/, the voltage of the conductance maximum, can be measured from electron tunneling spectrum. ..delta../kT can be found from this curve, then the energy gap ..delta.. can be calculated. This method is simple, fast and accurate. The accuracy almost approaches that of the curve fitting method.

1986-02-01

214

Computer-aided band gap engineering and experimental verification of amorphous silicon-germanium solar cells  

Energy Technology Data Exchange (ETDEWEB)

A new band gap profile (exponential profile) for the active layer of the a-SiGe:H single junction cell has been designed and experimentally demonstrated. By computer simulations we show how bending the grading of the band gap in the i-layer contributes to the enhancement of the carrier collection, improving the fill factor and efficiency. The differences observed between experiments and simulations are studied using Rutherford Backscattering Spectrometry (RBS). The results highlight weak points during the deposition process, whose control enables us to bring together experimental and computational results.

2004-01-25

215

Thin TiO2 grown by metal?organic chemical vapor deposition on (NH4)2S x -treated InP  

British Library Electronic Table of Contents (United Kingdom)

The electrical characteristics of thin TiO2 films prepared by metal?organic chemical vapor deposition grown on a p-type InP substrate were studied. For a TiO2 film of 4.7?nm on InP without and with ammonium sulfide treatment, the leakage currents are 8.8?10?2 and 1.1?10?4?A/cm2 at +2 V bias and 1.6?10?1 and 8.3?10?4?A/cm2 at ?2?V bias. The lower leakage currents of TiO2 with ammonium sulfide treatment arise from the improvement of interface quality. The dielectric constant and effective oxide charge number density are 33 and 2.5?1013?cm2, respectively. The lowest mid-gap interface state density is around 7.6?1011?cm?2?eV?1. The equivalent oxide thickness is 0.52?nm. The breakdown electric field increases with decreasing thickness in the range of 2.5 to 7.6?nm and reaches 9.3?MV/cm at 2.5?n...

2011-01-01

216

Theoretical investigation on quinoline-based platinum (II) complexes as efficient singlet oxygen photosensitizers in photodynamic therapy  

British Library Electronic Table of Contents (United Kingdom)

Geometry optimizations of the quinoline-based platinum (II) complexes (1-R, 2-R) and their related calculations on excited state energies, electronic absorption spectra and orbital populations have been carried out by the hybrid density functional theory (DFT) and its time-dependent approach (TD-DFT). The solvent effects on excitation energies are taken into account using the conductor-like polarizable continuum model (C-PCM). The red-shifted level of absorption bands, energy gaps between the singlet ground state (S1) and the first triplet excited state (T1) for each examined complex have been elaborated thoroughly as well. We find that the quinoline-8-thoil (ligand 2) induces much more significant red-shifted level than 8-hydroxyquinoline (ligand 1), and singlet-triplet splitting energy g...

2011-01-01

217

The validity of the density scaling method in primary electron transport for photon and electron beams  

International Nuclear Information System (INIS)

In the convolution/superposition method of photon beam dose calculations, inhomogeneities are usually handled by using some form of scaling involving the relative electron densities of the inhomogeneities. In this paper the accuracy of density scaling as applied to primary electrons generated in photon interactions is examined. Monte Carlo calculations are compared with density scaling calculations for air and cork slab inhomogeneities. For individual primary photon kernels as well as for photon interactions restricted to a thin layer, the results can differ significantly, by up to 50%, between the two calculations. However, for realistic photon beams where interactions occur throughout the whole irradiated volume, the discrepancies are much less severe. The discrepancies for the kernel calculation are attributed to the scattering characteristics of the electrons and the consequent oversimplified modeling used in the density scaling method. A technique called the kernel integration ...

218

Review of the occupational hygiene implications of the manufacture and use of nanoparticles  

Environmental Research Database

SummaryNanoparticles are increasingly being used in industry. Their potential to cause adverse health effects is due to their very small particles size (less than 100nm). A review is to be carried out to explore a) the use/release of nanoparticles in industry, b) current practices to control exposure and c) the potential levels of workplace exposure. The report will contain a discussion of what is current best practice to control exposure to nanoparticles. It will also indicate where the gaps in kn [continued...]ObjectivesA written report that draws upon disparate sources of available information and uses competent occupational hygiene expertise to form expert opinion on the implications. Key measures will the demonstration reasoned arguments supported by data from both current deliberate manufacturing of nanoparticles and incident nanoparticle production. The report will include all viable occupational exposure routes.Description1. Identify ...

2004-01-29

219

Renewable energy technology from underpinning physics to engineering application  

International Nuclear Information System (INIS)

The UK Energy Research Centre (UKERC) in it's submission to the DTI's 2006 Energy Review reminded us that the 'UK has abundant wind, wave and tidal resources available; its mild climate lends itself to bio-energy production, and solar radiation levels are sufficient to sustain a viable solar industry'. These technologies are at different stages of development but they all draw on basic and applied Science and Engineering. The paper will briefly review the renewable energy technologies and their potential for contributing to a sustainable energy supply. Three research topics will be highlighted that bridge the gap between the physics underpinning the energy conversion, and the engineering aspects of development and deployment; all three are highly relevant to the Government's programme on micro-generation. Two are these are taken from field of thin film photovoltaics (PV), one related to novel device development and the other to a measurement technique for assessing ...

2008-03-01

220

Ising model for phase separation in alloys with anisotropic elastic interaction. 2: A computer experiment  

Energy Technology Data Exchange (ETDEWEB)

When a metallic alloy is quenched into a miscibility gap, a mixture of two phases develops, whose domain structure then coarsens because of the interfacial energy between the two phases. This spatial arrangement of the domains and the rate at which they evolve may be strongly influenced by elastic interactions. In a recent paper, the authors described a method for simulating the effect of anisotropic elastic interactions in a two-dimensional Ising model of a cubic alloy, using Kawasaki dynamics with the elastic interactions represented by a long-range two-body interaction potential. Here they present the results of such simulations at various temperatures, alloy compositions and misfits (by misfit they mean the difference in size between the two kinds of atom), exhibiting snapshots both of the microscopic configurations (corresponding to experimental measurements using transmission electron microscopy) and of their squared Fourier transforms ...

1996-08-01

221

Fundamental state quantities and high-pressure phase transition in beryllium chalcogenides  

International Nuclear Information System (INIS)

In this work we study the structural and electronic properties of Be chalcogenides (BeS, BeSe and BeTe) using two different methods: the full-potential linear augmented-plane wave (FP-LAPW) and the plane-wave pseudopotential (PPsPW). The exchange-correlation effects are treated in the local-density approximation (LDA) and the generalized-gradient approximation (GGA). We have evaluated the ground-state quantities such as equilibrium volume, bulk modulus and its pressure derivative as well as the elastic constants. Various structural phase transitions were considered here in order to confirm the most stable structure and to predict the phase transition under hydrostatic pressure. In addition we have studied the band structure and the density of states, which show a wide indirect band gap for these compounds. These results were in favourable agreement with previous theoretical works and the existing experimental data. To complete the fundamental ...

2006-11-22

222

Fuel assembly and reactor core  

International Nuclear Information System (INIS)

In a fuel assembly having moderator rods, an axial average value of a ratio between the total of the lateral cross sectional area of a portion to be filled with moderators and the total of the lateral cross sectional area of fuel pellets is determined as greater than 0.4, a lateral cross sectional area of a portion to be filled with moderators per one moderator rod is determined as from 14 to 50cm"2 and the ratio between the total of the lateral cross sectional area of moderators and a total of the lateral cross sectional area of fuel pellets in a horizontal cross section is determined as from 2.7 to 3.4. Since the axial average value for lateral cross sectional area of a portion to be filled with moderators/lateral cross sectional area of fuel pellets is determined as #>=# 0.4, the lateral cross sectional area of moderators of moderator rods is increased, the lateral cross sectional area of a gap water region is decreased to reduce the value of local power ...

1992-12-03

223

Experimental and analytical studies of 4-inch pipe whip tests under PWR LOCA conditions  

International Nuclear Information System (INIS)

The purposes of the pipe rupture studies at the Japan Atomic Energy Research Institute are to perform the model tests on the pipe whip of a pipe-restraints system, to get jet impingement force and blowdown thrust force, and to establish the computational method for the analysis of these phenomena. This paper presents the experimental and analytical results of the pipe whip tests carried out under the PWR LOCA conditions using the test pipe of 4-inch diameter and the U-shaped restraints. In the tests, the gap between the test pipe and the restraints was set nearly constant and the overhang length was 250 mm, 400 mm or 650 mm. The dynamic strains and residual deformations of the test pipe and restraints, and the restraint force were measured to clarify the effects of the overhang length on the pipe whip behaviors of the pipe-restraints system. It was confirmed from the pressure data that the present pipe whip tests were performed under the PWR ...

224

Effects of CdCl2 treatment on properties of CdTe thin films grown by evaporation at low substrate temperatures  

International Nuclear Information System (INIS)

The structural, morphological and optical properties of vacuum-evaporated CdTe thin films were investigated as a function of substrate temperature and post-deposition annealing without and with CdCl2/treatment at 400 C for 30 min. Diffraction patterns are almost the same exhibiting higher preferential orientation corresponding to (111) plane of the cubic phase. The intensity of the (111) peak increased with the CdCl2/annealing treatment. The microstructure observed for all films following the CdCl2/annealing treatment are granular, regardless of the as-deposited microstructure. The grain sizes are increased after the CdCl2/annealing treatment but now contain voids around the grain boundaries. The optical band gaps, Eg, were found to be 1.50, 1.50 and 1.48 eV for films deposited at 200 K and annealed without and with CdCl2/treatment at 400 C for 30 min respectively. A progressive sharpening of the absorption edge upon heat treatment particularly for the ...

2007-09-01

225

Copper sulfates as cathode materials for Li batteries  

Energy Technology Data Exchange (ETDEWEB)

As lithium battery technology sets out to bridge the gap between portable electronics and the electrical automotive industry, cathode materials still stand as the bottleneck regarding performances. In the realm of highly attractive polyanion-type structures as high-voltage cathode materials, the sulfate group (SO{sub 4}){sup 2-} possesses an acknowledged superiority over other contenders in terms of open circuit voltage arising from the inductive effect of strong covalent S-O bonds. In parallel, novel lithium insertion mechanisms are providing alternatives to traditional intercalation, enabling reversible multi-electron processes securing high capacities. Combining both of these advantageous features, we report here the successful electrochemical reactivity of copper sulfate pentahydrate (CuSO{sub 4}.5H{sub 2}O) with respect to lithium insertion via a two-electron displacement reaction entailing the extrusion of metallic copper at a dual ...

2011-02-01

226

CANFLEX-NU fuel licensing status and issues in Korea  

International Nuclear Information System (INIS)

The CANFLEX-NU Fuel Design Report (FDR) for Wolsung 1,2,3,4 was submitted for licensing review in July 1996. The FDR contains sections of fuel rod design, fuel bundle design, nuclear design and thermal-hydraulic design. Each section describes the design bases, design methodology and design evaluation results showing that the design bases are met. The CANFLEX-NU fuel design is not finalized yet in Korean licensing point of view. For example, among others, new Xc-BL correlation is needed to be developed, fuel rod gap reduction effect is to be considered in the Critical Heat Flux, more information for power ramp defect of fuel rod especially in the end-cap weld region is needed in the fuel rod design, and enough data are not available in irradiated conditions in the fuel rod and bundle designs. The specific detailed technical licensing issues and their backgrounds are explained for the CANFLEX-NU FDR in Korea. The Korean nuclear regulation ...

1999-09-26

227

Behaviour of nonlinear supports on a PWR coolant system during a postulated LOCA. Pt. 1; Effect of modelling methods  

Energy Technology Data Exchange (ETDEWEB)

A 4-loop Pressurised Water Reactor (PWR) primary coolant system has been analysed for the postulated Loss of Coolant Accident (LOCA) event in order to derive peak dynamic loads for qualifying the design of equipment supports and pipe whip restraints. Pipe whip restraints as well as pipe and equipment supports are nonlinear by nature because of the presence of gaps and the different directional stiffnesses arising from snubber, steelwork and geometric and material interaction at the concrete to steel embedment. The different structural idealisations for the supports and restraints have an influence on the dynamic response of the structure. In the first of the two part paper a range of idealisation models for the Steam Generator and Reactor Coolant Pump vertical columns ranging from elastic stiffnesses to bilinear stiffnesses with or without preload were examined. Due to both structural and loading complexity, the behaviour of these supports were analysed by the ...

1993-07-01

228

Analysis of solar receiver flux distributions for US/Russian solar dynamic system demonstration on the Mir space station  

Energy Technology Data Exchange (ETDEWEB)

The United States and Russia have agreed to jointly develop a solar dynamic (SD) system for flight demonstration on the Russian Mir space station starting in late 1997. Two important components of this SD system are the solar concentrator and heat receiver provided by Russia and the US, respectively. This paper describes optical analysis of the concentrator and solar flux predictions on target receiver surfaces. The optical analysis is performed using the code CIRCE2. These analyses account for finite sun size with limb darkening, concentrator surface slope and position errors, concentrator petal thermal deformation, gaps between petals, and the shading effect of the receiver support struts. The receiver spatial flux distributions are then combined with concentrator shadowing predictions. Geometric shadowing patterns are traced from the concentrator to the target receiver surfaces. These patterns vary with time depending on the chosen Mir ...

1995-12-31

229

An empirical comparison of alternate regime-switching models for electricity spot prices  

International Nuclear Information System (INIS)

One of the most profound features of electricity spot prices are the price spikes. Markov regime-switching (MRS) models seem to be a natural candidate for modeling this spiky behavior. However, in the studies published so far, the goodness-of-fit of the proposed models has not been a major focus. While most of the models were elegant, their fit to empirical data has either been not examined thoroughly or the signs of a bad fit ignored. With this paper we want to fill the gap. We calibrate and test a range of MRS models in an attempt to find parsimonious specifications that not only address the main characteristics of electricity prices but are statistically sound as well. We find that the best structure is that of an independent spike 3-regime model with time-varying transition probabilities, heteroscedastic diffusion-type base regime dynamics and shifted spike regime distributions. Not only does it allow for a seasonal spike intensity throughout the year and ...

2010-09-01

230

A framework for assessing relative risks associated with multiple stressors in Port Valdez, Alaska  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this assessment is to develop a versatile process that will provide a mechanism for evaluating both present and future risks to this environment. Much of the regulatory and environmental interest in the port has centered around a Ballast Water Treatment facility that treats and discharges up to 30 mgd of oily ballast water brought in by crude oil tankers. However, six point discharges and other potential sources of pollution exist in the area. The authors have delineated eleven subareas in the port in order to identify the potential anthropogenic stressors, as well as the receptors that could be exposed to these stressors. Potential effects were then characterized for each exposure. Each component is ranked and integrated, resulting in a relative risk estimate in each subarea. Both the discernible risks, based on available data, and the data gaps are presented. Uncertainty is expressed as a range of high and low risk associated ...

1995-12-31

231

Spin-up of He II in a cylindrical vessel of finite height  

Energy Technology Data Exchange (ETDEWEB)

The spin-up problem of He II in a cylindrical container of infinite and finite height is considered on the basis of the Hall-Vinen-Bekarevich-Khalatnikov equations. The boundary conditions include the assumption of the generation of superfluid vorticity at the walls of the container. In the lowest order approximation with respect to viscosity, the problem is reduced to a Stefan problem for a single diffusion-type equation. Examples of solutions are given which show that the method used gives a good insight into the physical development of the spin-up flow.

1990-01-01

232

The hidden secrets of the E-center in Si and Ge  

Energy Technology Data Exchange (ETDEWEB)

The group- V vacancy pair, the so-called E-center, has recently been demonstrated to have, both in Si and Ge, more complicated energy-level schemes in the energy gap than were previously assumed. The E-center in silicon has, in addition to its well-established single-acceptor level in the upper half of the band gap, also a donor level in the lower half of the band gap; this donor level has lain hidden for more than 40 years. The E-center in Ge has an even more complicated level scheme as it induces, in addition to two levels analogous to those found in Si, also a double-acceptor level in the upper half of the band gap. Thus the E-center in Si can exist in three charge states and the E-center in Ge in four.

2007-12-15

233

The Influence of Inert Particulate Material on the Properties of ...  

Science.gov (United States)

... Briefly, a standard detonator (normally the Scale 1 Gap Test Donor, comprising an exploding bridgewire to initiate a low density PETN pellet and ...

1984-05-01

234

The Expanded Large Scale Gap Test  

Science.gov (United States)

... an Page 15. NSWC TR 86-32 exploding bridgewire detonator containing PETN rather, than a pri'mary explosive. However ...

1987-03-01

235

On the disrupted magnetic braking model for the period gap of cataclysmic variables  

International Nuclear Information System (INIS)

The disrupted magnetic braking theory for the period gap of cataclysmic variable systems is used to study the binary evolution of low-mass main-sequence-like stars with white dwarf companions. The model is able to reproduce the observed location and width of the gap provided that the average mass transfer rates above the upper edge of the gap are greater than about 1.9 x 10 to the -9th solar masses/yr. For the case of angular momentum loss by magnetic braking, the slope of the mass transfer rate with respect to orbital period is shown to range from 3.4 to 3.7. For the evolutionary sequences considered, the He-3 abundance at the surface of the secondary exceeds 0.0015 after the complete mixing phase, resulting in modifications in the nuclear burning development of nova explosions. 31 refs.

236

Modelling and design of smoothing reactances. Application to air gap length calculation  

Energy Technology Data Exchange (ETDEWEB)

A new method for analysis and design of smoothing reactances utilising two-dimensional planar models is presented in this paper. Inductance and magnetic flux density are calculated, and their results compared with those measured experimentally. The results obtained are good if compared with those measured once the machine have been built. Moreover, the method herein developed is applied to the calculation of air gap lengths in terms of the desired current and inductance. The kind of reactances studied presents windings in both limbs and air gaps in the four corners (joint of limbs and yokes). The main contribution of this paper is the presentation of a method of industrial application, to be easily developed, with a very important reduction in the time of machine calculation (due to the decrease in the number of nodes and elements compared with the three-dimensional model) for the determination of the air gap length in ...

2000-08-01

237

Comparison of energy flows in deep inelastic scattering events with and without a large rapidity gap  

Energy Technology Data Exchange (ETDEWEB)

Energy flows in deep inelastic electron-proton scattering are investigated at a centre-of-mass energy of 296 GeV for the range Q{sup 2}{>=}10 GeV{sup 2} using the ZEUS detector. A comparison is made between events with and without a large rapidity gap between the hadronic system and the proton direction. The energy flows, corrected for detector acceptance and resolution, are shown for these two classes of events in both the HERA laboratory frame and the Breit frame. From the differences in the shapes of these energy flows we conclude that QCD radiation is suppressed in the large-rapidity-gap events compared to the events without a large rapidity gap. (orig.)

1994-07-01

238

Army Transformation to Expeditionary Formations  

Science.gov (United States)

... gap" between the arrival ofquick response forces, such as the 82nd Airborne Division and the ... nd Airborne is just exactly that, light airborne infantry. ...

2011-05-14

239

Andreev reflection spectroscopy in MgB{sub 2}  

Energy Technology Data Exchange (ETDEWEB)

Our Andreev reflection measurements (Phys. Rev. Lett. 87 (2001) 137005) along with other experiments have led to a general consensus that MgB{sub 2} is a multiband superconductor with two main superconducting gaps closing at the same T{sub c}. Here we show the behavior of the small gap as a function of the temperature and magnetic field. This gap is isotropic with T{sub c} of the bulk material but with a specific small (crossover) critical magnetic field of about 1 T much lower than the real H{sub c2}. The latter field is anisotropic and is rather governed by the large gap and strongly anisotropic Fermi surface of the material.

2003-04-01

240

Magnetocaloric effect of Gd{sub 4}(Bi{sub x}Sb{sub 1{minus}x}){sub 3} alloy series  

Energy Technology Data Exchange (ETDEWEB)

Alloys from the Gd{sub 4}(Bi{sub x}Sb{sub 1{minus}x}){sub 3} series were prepared by melting a stoichiometric amounts of pure metals in an induction furnace. The crystal structure is of the anti-Th{sub 3}P{sub 4} type (space group I{bar 4}3d) for all the compounds tested. The linear increase of the lattice parameters with Bi concentration is attributed to the larger atomic radius of Bi than that of Sb. Magnetic measurements show that the alloys order ferromagnetically from 266K to 330K, with the ordering temperature increasing with decreasing Bi concentration. The alloys are soft ferromagnets below their Curie temperatures, and follow the Curie-Weiss law above their ordering temperatures. The paramagnetic effective magnetic moments are low compared to the theoretical value for a free Gd{sup 3+}, while the ordered magnetic moments are close to the theoretical value for Gd. The alloys exhibit a moderate magnetocaloric effect (MCE) whose maxima ...

1999-12-01

241

Effect of applied tensile stress on intergranular corrosion of AA2024-T3  

International Nuclear Information System (INIS)

The effect of uniaxial tensile stress on intergranular corrosion (IGC) of AA2024-T3 was studied using the foil penetration technique. Standard ASTM G49 fixed-displacement jigs were modified to allow the use of sheet samples, which were then attached to an electrochemical cell as in the foil penetration setup. The time for IGC to penetrate samples of varying thickness was monitored. This method provides a new approach to bridge the gap between IGC and intergranular stress corrosion cracking (IGSCC). Samples with various orientations relative to the rolling direction were studied in 1.0 M NaCl at controlled anodic potentials. Potentiodynamic polarization measurements indicated that the two breakdown potentials typically observed for AA2024-T3 were lower for stressed samples than for unstressed samples, and the current at a given potential was higher. The penetration rate depended on potential and was higher for stressed samples than for ...

2004-02-01

242

Numerical simulation of VAWT stochastic aerodynamic loads produced by atmospheric turbauence: VAWT-SAL code  

Energy Technology Data Exchange (ETDEWEB)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This report describes the theoretical background of the VAWT Stochastic Aerodynamic Loads (VAWT-SAL) computer code, whose purpose is to numerically simulate these random loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Stream Tube (DMST) analysis is employed to model the rotor's aerodynamic response. The analysis includes the effects of Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. The mean ambient wind is assumed to have a shear profile which is described by either a power law or a logarithmic variation with ...

1991-09-01

243

Incineration of wool-scouring sludge in a vertical-axis-spinning fluidised-bed incinerator  

Energy Technology Data Exchange (ETDEWEB)

The main purposes of this research was to investigate the feasibility of incineration of wool-scouring sludge in a novel vertical-axis-rotating fluidised bed (RFB). The experiment was carried out in a RFB with an internal diameter (ID) of 200 mm and height of 50 mm. A cold test was first conducted to investigate the fluidization performance of the RFB via parameters such as the bubbling, gas distribution, bed shape and pressure drop. The tumbling phenomena was observed in the bed, and this effectively enhanced the axial mixing. The appropriate range of bed thickness, rotating speed and sand particle size were identified to ensure the full fluidization and reduce the particle elutriation. Four wool-scouring sludges from different processes were incinerated in the RFB. With 5% support methane, all sludges with a maximum moisture up to 70% as received could be successfully burned in the RFB at rotating speeds of 200 and 300 rpm. The combustion was ...

2000-09-01

244

Heat transfer performance of a fin with two fences and tube heat exchanger. Study in the low Reynolds number range; Fence wo fusetsushita fin tsuki kan netsu kokanki unit no ryudo dennetsu sogo tokusei. Tei Reynolds suiki ni okeru kosatsu  

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional steady numerical computation was made for a component model of fin and tube type of compact heat exchangers situated in a uniform flow. In this study, in order to find a clue to design high-efficient heat exchangers, numerical computation was made in the case where two fences are attached on the plate fin surface and their geometrical effects such as their locations, their heights and their attack angles on flow and heat transfer characteristics were investigated especially in the low Reynolds number range. The effect of a hole, open in the plate fin behind the fence, on heat transfer and flow structures was also examined. This hole simulates the hole of the plate fin to be produced in practical application, when a fence is produced by punching from the original plain fin plate. Two fences with holes were found to show several important effects on flow and heat transfer structures ...

2000-07-25

245

Advanced Lighting Program Development (BG9702800) Final Report  

Energy Technology Data Exchange (ETDEWEB)

The report presents a long-range plan for a broad-based, coordinated research, development and market transformation program for reducing the lighting energy intensities in commercial and residential buildings in California without compromising lighting quality. An effective program to advance lighting energy efficiency in California must be based on an understanding that lighting is a mature field and the lighting industry has developed many specialized products that meet a wide variety of light needs for different building types. Above all else, the lighting field is diverse and there are applications for a wide range of lighting products, systems, and strategies. Given the range of existing lighting solutions, an effective energy efficient lighting research portfolio must be broad-based and diverse to match the diversity of the lighting market itself. The belief that there is one solution--a magic bullet, such as a better lamp, for ...

1998-02-01

246

LOBI/B-R1M, Loop for Blowdown Investigation, PWR Single-Ended Cold-Leg Break Experiment B EXP.B  

International Nuclear Information System (INIS)

1 - Description of test facility: The LOBI facility is a 1/700 scale model of a four loop PWR and has two primary loops, the intact loop representing three loops and the broken loop representing one loop of a four-loop PWR. The reactor pressure vessel model contains an electrically heated rod-bundle with 64 rods and a heated length of 3.9 m. The nominal heating power is 5.3 MW. The downcomer is of annular shape. An upper head simulator is connected to the vessel. Each of the two primary loops contains a pump and a steam generator. The different mass flows in the loops are established by the pump speeds, since the two pumps are identical. Heat is removed from the steam generators by a secondary system. ECC water can be supplied from two accumulators, one for each loop. Cold or hot leg as well as combined injection can be simulated. The LOBI test facility is the only high pressure integral test facility within the European Communities (1982), built and operated in the Joint Research ...

247

Bypass Flow and Hot Spot Analysis for PMR200 Block-Core Design with Core Restraint Mechanism  

Energy Technology Data Exchange (ETDEWEB)

The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the PMR200 block-core design. For the analysis not only are some ...

2009-10-15

248

Bypass Flow and Hot Spot Analysis for PMR200 Block-Core Design with Core Restraint Mechanism  

International Nuclear Information System (INIS)

The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the PMR200 block-core design. For the analysis not only are some ...

2009-10-01

249

Subcritical measurements with a cylindrical tank of Pu-U nitrate  

Energy Technology Data Exchange (ETDEWEB)

This series of measurements with a mixed Pu-U nitrate solution (280 g Pu/liter, 180 g U/liter) in a 35.54-cm-diam cylindrical tank provides a wide variety of experimental data for subcritical configurations that can be used to verify calculational methods and nuclear data. The Pu contained 7.85 wt% {sup 240}Pu and the uranium was natural uranium. The measurements performed were: inverse count rate, prompt neutron decay constants, inverse kinetics, and frequency analysis by the {sup 252}Cf source driven method. These data are presented in sufficient detail that the results of the experiments can be calculated directly. For purposes of extrapolating to the delayed critical height the ratio of spectral densities was linear with height and thus provided the best estimate of critical height.

1997-04-01

250

Prospects of wind energy in Bangladesh  

Energy Technology Data Exchange (ETDEWEB)

Wind speed has been measured in Patenga, Cox`s Bazar, Kuakata, Moheshkhali, and Noakhali by the computerized anemometers. The wind computers have been installed at 20 meters height. According to this study annual average wind speeds in the coastal regions of Bangladesh are greater than 6.5 m/s at the height of 20 meters. It has been observed that during day times (8 a.m. to 7 p.m.) wind speeds are about 30 to 40% higher than the average values. The value of the power exponent {alpha} has been determined in the above sites and it is 0.139. So, at 40 meters height the annual average wind speed is about 7.15 m/s. So, wind speeds in the coastal regions of Bangladesh are suitable for both water pumping and electricity generation. Details are given in this paper with graphical and analytical representations. (author)

1996-09-01

251

/sup 252/Cf-source-driven neutron noise measurements of subcriticality for a slab tank containing aqueous Pu-U nitrate  

Energy Technology Data Exchange (ETDEWEB)

In order to study nuclear criticality safety related to the development of fast breeder technology, /sup 252/Cf-source-driven neutron noise analysis measurements were performed with a Pu-U nitrate solution in a slab tank of various heights and thickness varying 11.43 cm to 19.05 cm. The results and conclusions of these experiments are (1) a capability to measure the subcriticality of a multiplying system of slab geometry to a k/sub eff/ as low as 0.7 was demonstrated, (2) calculated neutron multiplication factors agreed with those from the experiments within approx.0.02, and (3) the applicability of the method for plutonium solution systems was demonstrated. This paper describes measurements in which the height of the slab was varied for a fixed thickness and the thickness varied for a fixed height, which are the first applications of this measurement method to slab geometry.

1987-08-01

252

Optical image storage in ion implanted PLZT ceramics  

International Nuclear Information System (INIS)

We have demonstrated that optical images can be stored in transparent lead-lanthanum-zirconate-titanate (PLZT) ceramics by exposure to near-UV light with photon energies greater than the band gap energy of approx. equal to 3.35 eV. The image storage process relies on optically induced changes in the switching properties of ferroelectric domains (photoferroelectric effect). Stored images are nonvolatile but can be erased by uniform UV illumination and simultaneous application of an electric field. Although high quality images, with contrast variations of >= 100:1 and spatial resolution of approx. equal to 10 #mu#m, can be stored using the photoferroelectric effect, relatively high exposure energies (approx. equal to 100 mJ/cm"2) are required to store these images. This large exposure energy severely limits the range of possible applications of nonvolatile image storage in PLZT ceramics. We have recently found from studies ...

253

Effects of reactor configuration on the performance of static-bed submerged media anaerobic reactors  

Energy Technology Data Exchange (ETDEWEB)

Three different configurations of cylindrical submerged media anaerobic reactors (SMARs) with packing volumes of 85 items were operated at 35 C for 415 days with COD loading rates varying from 1 to 12 g/l/d and three retention times of 0.5, 1, and 2 days. A synthetic waste consisting of a milk solution with a mineral supplement was used for the feed. Tracer studies on clean-bed and dirty-bed SMARs indicate that reactor configuration, biogas mixing, and biomass accumulation all have a significant effect on SMAR hydraulics and cause short-circuiting. Based on the isothermal energy dissipation theory, the higher hydrostatic pressures resulting from higher SMAR heights increases self-induced biogas mixing and improves the contact efficiency between substrate and organisms. Based on TCOD removal rate, the tallest SMAR performed slightly better at COD loading rates above 4/g/l/d. At COD loading rates equal to or below 4 g/l/d, there was little ...

1988-01-01

254

Airway problems in children--can the orthodontist help?  

Science.gov (United States)

The adequacy of the nasopharyngeal airway has been found to be related to craniofacial development. Obstruction of the airway by adenoid tissue, nasal septal deviation or abnormal morphology of the area is associated with characteristic changes in craniofacial morphology such as long anterior face height, facial retrognathism, and a steep inclination of mandibular plane often with a high vaulted palate and crossbite. Some studies have shown the changes to be reversible after adenoidectomy which improves nasal airway patency and a control mechanism for facial growth has been proposed to account for the relationships between airway adequacy, craniofacial morphology and craniocervical postural relationships. It is therefore important to be able to measure nasal respiratory resistance so that the effect of operative procedures in the area such as rapid maxillary expansion (RME) can be determined. Nasal respiratory resistance (NRR) is a measure of ...

1995-01-01

255

Aerosol-induced changes of convective cloud anvils produce strong climate warming  

Science.gov (United States)

The effect of aerosol on clouds poses one of the largest uncertainties in estimating the anthropogenic contribution to climate change. Small human-induced perturbations to cloud characteristics via aerosol pathways can create a change in the top-of-atmosphere radiative forcing of hundreds of Wm-2. Here we focus on links between aerosol and deep convective clouds of the Atlantic and Pacific Intertropical Convergence Zones, noting that the aerosol environment in each region is entirely different. The tops of these vertically developed clouds consisting of mostly ice can reach high levels of the atmosphere, overshooting the lower stratosphere and reaching altitudes greater than 16 km. We show a link between aerosol, clouds and the free atmosphere wind profile that can change the magnitude and sign of the overall climate radiative forcing. We find that increased aerosol loading is associated with taller cloud towers and anvils. The taller clouds reach levels of ...

2010-05-01

256

Thermal dislocation depinning in a deformed crystal  

Energy Technology Data Exchange (ETDEWEB)

The temperature dependence of the dislocation mobility threshold is investigated on the basis of a dislocation model suggested by Frenkel-Kontorova. The critical value is obtained for the stress/temperature, corresponding to the dislocation depinning from its equilibrium position. The universal behaviour of a barrier height at finite stress and temperature is revealed and investigated.

2008-01-14

257

Secular changes in height, weight and body mass index in Hong Kong Children  

UK PubMed Central (United Kingdom)

BackgroundLarge population growth surveys of children and adolescents aged 6 to 18 y were undertaken in Hong Kong in 1963 and 1993. The global epidemic of obesity is a major public...Full Text Available

258

Radiological kidney size in childhood  

Energy Technology Data Exchange (ETDEWEB)

Kidney length (KL), renal area and renal parenchymal area were measured on i.v. urograms of 255 children without apparent kidney disease age 0 to 14 years. These parameters were compared with age, body height, body surface area and the distance between the 1sup(s)sup(t) and 4sup(t)sup(h) lumbar vertebral body. In addition, renal parenchymal thickness was determined at the upper and lower poles. Mean values for normal KL were significantly greater on the left side than on the right side requiring separate growth charts. A mean increase in KL of 6.3 mm for the left and 6.0 mm for the right kidney was calculated for a change of 10 cm body height. A small kidney is defined by a KL below -2 SD for the corresponding body height and/or a quotient of right KL/left KL outside +-2 SD from the mean value. Localised loss of renal parenchyma is reflected by an increased or decreased quotient of the upper to the lower polar thickness and ...

1980-04-01

259

Radiological kidney size in childhood  

International Nuclear Information System (INIS)

Kidney length (KL), renal area and renal parenchymal area were measured on i.v. urograms of 255 children without apparent kidney disease age 0 to 14 years. These parameters were compared with age, body height, body surface area and the distance between the 1sup(s)sup(t) and 4sup(t)sup(h) lumbar vertebral body. In addition, renal parenchymal thickness was determined at the upper and lower poles. Mean values for normal KL were significantly greater on the left side than on the right side requiring separate growth charts. A mean increase in KL of 6.3 mm for the left and 6.0 mm for the right kidney was calculated for a change of 10 cm body height. A small kidney is defined by a KL below -2 SD for the corresponding body height and/or a quotient of right KL/left KL outside +-2 SD from the mean value. Localised loss of renal parenchyma is reflected by an increased or decreased quotient of the upper to the lower polar thickness and ...

260

Lin28a transgenic mice manifest size and puberty phenotypes identified in human genetic association studies  

UK PubMed Central (United Kingdom)

Recently, genome-wide association studies (GWAS) have linked the human LIN28B locus to height and timing of menarche [1-Full Text Available

2010-07-01

261

Increase in Internode Length of Phaseolus lunatus L. Caused by Inoculation with a Nitrate Reductase-deficient Strain of Rhizobium sp. 1  

UK PubMed Central (United Kingdom)

Dramatic differences in the height of lima beans (Phaseolus lunatus L.) treated with two different Rhizobium strains were studied. Lima beans were grown in Perlite...Full Text Available

1981-01-01

262

Improved DNA Sequencing Accuracy and Detection of Heterozygous Alleles Using Manganese Citrate and Different Fluorescent Dye Terminators  

UK PubMed Central (United Kingdom)

The use of dideoxynucleotide triphosphates labeled with different fluorescent dyes (dye terminators) is the most versatile method for automated DNA sequencing. However, variation in peak heights reduces...Full Text Available

1999-06-01

263

Growth velocity and stunting in rural Nepal.  

UK PubMed Central (United Kingdom)

In a community based study, height and weight increments of 441 Nepali children aged 0-6 years were measured before harvest and six months later and compared with centile standards derived from American...Full Text Available

1989-10-01

264

Developments of heavy-ion gas detectors at LNL  

Energy Technology Data Exchange (ETDEWEB)

The most important developments in gaseous detectors at LNL are reviewed. Some aspects of timing, pulse height and position resolutions of avalanche counters are reported. The experimental work on heavy-ion identification by Bragg curve spectroscopy is summarized.

1984-05-01

265

Case series of maxillary sinus augmentation with biphasic calcium phosphate: a clinical and radiographic study  

UK PubMed Central (United Kingdom)

PurposeThe aim of this study was to evaluate 3.5 years-cumulative survival rate of implants placed on augmented sinus using Osteon, a bone graft material, and to assess the height...Full Text Available

2011-04-01

266

Nasal cavity volume measured in normal persons by MRI  

Energy Technology Data Exchange (ETDEWEB)

Nasal cavity volume was studied in 69 healthy volunteers (from 8 to 23 years old) by MRI. The right and left nasal cavity areas were measured on horizontal images displayed directly on the MRI console. The nasal cavity volume was obtained by integrated volume calculation. The nasal cavity volume was positively correlated with age, body height and weight up to age 16. The body height and weight reached a plateau at 16 years, but the nasal cavity volume continued to increase. There was no significant difference in the volumes of the right and left cavities. (author).

1993-10-01

267

Nasal cavity volume measured in normal persons by MRI  

International Nuclear Information System (INIS)

Nasal cavity volume was studied in 69 healthy volunteers (from 8 to 23 years old) by MRI. The right and left nasal cavity areas were measured on horizontal images displayed directly on the MRI console. The nasal cavity volume was obtained by integrated volume calculation. The nasal cavity volume was positively correlated with age, body height and weight up to age 16. The body height and weight reached a plateau at 16 years, but the nasal cavity volume continued to increase. There was no significant difference in the volumes of the right and left cavities. (author).

268

Mathematical child phantom for the calculation of dose to the organs at risk  

Energy Technology Data Exchange (ETDEWEB)

In order to calculate the doses received by the organs of 530 children treated by radiation for cancer between 1945 and 1969 at the G. Roussy Institute, we have developed a computer program for organ location calculation. To calculate the location of each child's organs of interest at the time of the treatment, only two parameters are necessary; sex and height or sex and age when the height at the time of the treatment is unknown. The algorithm is based on the metric studies of growth known as auxology. Each organ is located by one point representing its center. The model has been checked on 100 healthy children.

1988-05-01

269

Determining surface profile from sequential interference patterns from a long trace profiler  

Energy Technology Data Exchange (ETDEWEB)

The Long Trace Profiler (Takacs et al.) is a slope-measuring instrument which was introduced several years ago. Development of this instrument continues at Lawrence Berkeley Laboratory in improving both hardware design and software algorithms for turning the raw interference data (a sequence of intensity patterns) into properly interpreted representations of surface slope and height. This report presents a mathematical model of the interference pattern and methods of extracting the slope and height profile from such patterns. 9 refs.

1991-07-01

270

Experimental study on heat transfer augmentation for high heat flux removal in rib-roughened narrow channels  

International Nuclear Information System (INIS)

Frictional pressure drop and heat transfer performance in a very narrow rectangular channel having one-sided constant heat flux and repeated-ribs were studied experimentally for turbulent water flows. Their empirical correlations were derived for designing target cooling channels to remove high heat flux generated at target plates in a high-intensity proton accelerator system. The rib pitch-to-height ratios (p/k) were 10 and 20 while holding the rib height constant at 0.2 mm, the Reynolds number (Re) from 2,400 to 98,500 under different channel heights (H) of 1.2 mm and 3.2 mm, the rib height-to-channel equivalent diameter ratio (k/D_e) of 0.088 and 0.036, respectively. The results show that the rib-roughened surface augments heat transfer by about 2-2.5 times compared with the smooth surface at the expense of around 2.5 times higher frictional pressure drop under a range of Re=8,000-to-30,000 at ...

1998-09-01

271

Bone age estimation and prediction of final height in patients with {beta}-thalassaemia major: a comparison between the two most common methods  

Energy Technology Data Exchange (ETDEWEB)

Thalassaemic patients are in need of frequent assessment of bone age because of growth failure and pubertal disorders. To compare the ''rapid'' Greulich and Pyle (G and P) method with the third edition of the Tanner and Whitehouse (TW3) method for determining skeletal maturity and predicting final height in thalassaemic patients. A total of 191 radiographs from 58 patients (28 male, 30 female) were retrospectively evaluated by two investigators, one for each method. In 47 radiographs from 15 patients having attained their adult height, predicted final height was calculated according to each method. The mean bone ages determined by both the G and P and TW3 methods were lower than mean chronological age, although the differences were not statistically significant (10.04 {+-} 3.69 years and 9.98 {+-} 3.39 years vs. 10.78 {+-} 3.96 years, respectively). Both methods had a tendency to ...

2007-12-15

272

A lateral cephalometric study of the size of tongue and intermaxillary space in Korean  

International Nuclear Information System (INIS)

A study was performed to investigate the size of tongue area and intermaxillary space area, and compare the sexual differences between normal Korean children and adults by introducing planimetric and linear analysis of the lateral cephalograms. The cephalograms were composed of 41 child male aged 10.8, 40 child female aged 10.5, 38 adult male aged 21.3 , and 40 adult female aged 20.8 respectively. In order to study and measure the intermaxillary space area, the following were selected, as reference items: occlusal plane, anterior intermaxillary space height, posterior intermaxillary space height, length of intermaxillary space. Among those reference items anterior intermaxillary space height and posterior intermaxillary space height were perpendicular to the maxillary plane. An index, (Anterior intermaxillary space height + posterior intermaxillary space height ...

1977-11-01

273

Simplified electrostatic model for band-gap underestimates in the local-density approximation  

Science.gov (United States)

An estimate of the undercounted electrostatic energy terms in local-density-functional total-energy calculations for nonmetallic systems with separated electron-hole pairs is used to derive a simplified correction to density-functional - theory band gaps. The correction is evaluated for Ne, Ar, Kr, LiF, NaCl, CsCl, MgO, CaS, BaS, C, AlP, and Si. The band-gap errors are reduced from 40-50% to 10-15% for most of the systems studied. Conduction-band corrections are shown to be nearly as large as valence-band corrections in free-electron-like semiconductors. 28 references, 1 figure.

1985-04-15

274

Seismic tests of post-tensioned self-centering building frames with column and slab restraints  

British Library Electronic Table of Contents (United Kingdom)

Post-tensioned (PT) self-centering moment frames have been developed as an alternative to typical moment-resisting frames (MRFs) for earthquake resistance. When a PT frame deforms laterally, gaps between the beams and columns open. However, the gaps are constrained by the columns and the slab in a real PT self-centering building frame. This paper presents a methodology for evaluating the column restraint and beam compression force based on the column deformation and gap openings at all stories. The method is verified by cyclic tests of a full-scale, two-bay by one-story PT frame. Moreover, a sliding slab is proposed to minimize restraints on the expansion of the PT frame. Shaking table tests were conducted on a reduced-scale, two-by-two bay one-story specimen, which comprises one PT frame ...

2011-01-01

275

Point contact Andreev reflection spectroscopy of NdFeAsO_0_._8_5  

International Nuclear Information System (INIS)

The newly discovered oxypnictide family of superconductors show very high critical temperatures of up to 55 K. Whilst there is growing evidence that suggests a nodal order parameter, point contact Andreev reflection spectroscopy can provide crucial information such as the gap value and possibly the number of energy gaps involved. For the oxygen deficient NdFeAsO_0_._8_5 with a T_c of 45.5 K, we show that there is clearly a gap value at 4.2 K that is of the order of 7 meV, consistent with previous studies on oxypnictides with lower T_c. In addition, taking the spectra as a function of gold tip contact pressure reveals important changes in the spectra which may be indicative of more complex physics underlying this structure. (rapid communication)

2008-09-01

276

Optimization of band gap of photonic crystals fabricated by holographic lithography  

Science.gov (United States)

Generally the photonic band gap (PBG) is a multi-variable function of several parameters related to the shape and size of the dielectric columns of photonic crystals (PhCs), and a time-consuming step-by-step scanning process for each parameter has to be used to find their best combination yielding maximum PBG. In this letter, the widely used Nelder-Mead simplex algorithm is introduced to optimize these parameters simultaneously to find a larger PBG for a new kind of two-dimensional (2D) hexagonal GaAs-Air PhC. This structure can be conveniently produced by the single-exposure holographic lithography, and the specific holographic design is also systematically investigated. This study reveals that the band gaps of PhCs made by holographic lithography may be widened by introducing irregularity of the columns and lowering the symmetry of the structure.

2008-01-01

277

Electronic properties of low temperature microcrystalline silicon carbide prepared by Hot Wire CVD  

Energy Technology Data Exchange (ETDEWEB)

Microcrystalline silicon carbide ({mu}c-SiC) was prepared at low substrate temperatures using Hot Wire chemical vapor deposition (HWCVD). High crystalline volume fractions were achieved at high hydrogen dilution and high deposition pressure. Without intentional doping, such material shows high dark conductivity and high optical absorption below the band gap. The material prepared at low deposition pressure or low hydrogen dilution, on the other hand, shows much lower conductivity and sub-gap absorption, but high spin densities up to 5 x 10{sup 19} cm{sup -3}. This high absorption can be attributed to free carriers, different to {mu}c-Si:H where a correlation between the sub-gap absorption and the spin density is observed.

2008-01-15

278

A comparative assessment of slope stability of New Orleans I-wall with partial gap between the wall and layered cohesive backfill  

British Library Electronic Table of Contents (United Kingdom)

Following Hurricane Katrina, the study of cantilevered sheet pile I-wall with gap or partial gap has become one of the central elements of the ongoing investigation pertaining to the re-building of hurricane protection systems in New Orleans, LA. Historically, the US Army Corps of Engineers (USACE) had mostly relied upon the Method of Planes (MOP) analysis procedure for slope stability analysis of I-wall systems. However MOP is a simplified procedure which does not satisfy total equilibrium. Nevertheless, MOP is still considered by USACE as a popular analysis tool because of its simplicity and ease of use in slope stability analysis. This paper demonstrates the applicability and suitability of MOP as a viable analysis tool for the analysis of New Orleans I-wall founded on layered cohesive ...

2011-01-01

279

[Magnetic thin film research]: Progress report year 2  

Energy Technology Data Exchange (ETDEWEB)

The work in the past year has primarily involved four areas of magnetic thin films: amorphous rare earth-transition metal alloys, epitaxial CoPt{sub 3} and Ni-Pt alloy thin films, amorphous rare earth doped Si (a new class of dilute magnetic semiconductor with large negative magnetoresistance which the authors have discovered), and exchange-coupled antiferromagnetic insulators. In the amorphous alloys, they made a systematic study of the effects of local anisotropy, macroscopic (perpendicular) anisotropy, and exchange constant on the fundamental (and practical) properties of these magnetic alloys, as originally described in the grant proposal. The work on the epitaxial Co-Pt (and more recently Ni-Pt) alloys was originally undertaken as a comparison study to the amorphous alloys. Crystalline Co-Pt alloys have many striking similarities to the amorphous rare earth-transition metal alloys: perpendicular magnetic anisotropy, magneto-optic activity, and a {Tc} (for ...

1996-09-01

280

The research agenda in ICU telemedicine: a statement from the Critical Care Societies Collaborative.  

Science.gov (United States)

ICU telemedicine uses audiovisual conferencing technology to provide critical care from a remote location. Research is needed to best define the optimal use of ICU telemedicine, but efforts are hindered by methodological challenges and the lack of an organized delivery approach. We convened an interdisciplinary working group to develop a research agenda in ICU telemedicine, addressing both methodological and knowledge gaps in the field. To best inform clinical decision-making and health policy, future research should be organized around a conceptual framework that enables consistent descriptions of both the study setting and the telemedicine intervention. The framework should include standardized methods for assessing the preimplementation ICU environment and describing the telemedicine program. This framework will facilitate comparisons across studies and improve generalizability by permitting context-specific interpretation. Research based on this framework ...

2011-07-01

281

Saturated bonds and anomalous electronic transport in transition-metal aluminides  

Energy Technology Data Exchange (ETDEWEB)

This thesis deals with the special electronic properties of the transition-metal aluminides. Following quasicrystals and their approximants it is shown that even materials with small elementary cells exhibit the same surprising effects. So among the transition-metal aluminides also semi-metallic and semiconducting compounds exist, although if they consist of classic-metallic components like Fe, Al, or Cr. These properties are furthermore coupled with a deep pseusogap respectively gap in the density of states and strongly covalent bonds. Bonds are described in this thesis by two eseential properties. First by the bond charge and second by the energetic effect of the bond. It results that in the caes of semiconducting transition-metal aluminides both a saturation of certain bonds and a bond-antibond alteration in the Fermi level is present. By the analysis of the near-order in form of the so-calles coordination polyeders it ...

2006-05-22

282

NATURAL GAS VARIABILITY IN CALIFORNIA: ENVIRONMENTAL IMPACTS AND DEVICE PERFORMANCE EXPERIMENTAL EVALUATION OF POLLUTANT EMISSIONS FROM RESIDENTIAL APPLIANCES  

Science.gov (United States)

The effect of liquefied natural gas on pollutant emissions was evaluated experimentally with used and new appliances in the laboratory and with appliances installed in residences, targeting information gaps from previous studies. Burner selection targeted available technologies that are projected to comprise the majority of installed appliances over the next decade. Experiments were conducted on 13 cooktop sets, 12 ovens, 5 broiler burners, 5 storage water heaters, 4 forced air furnaces, 1 wall furnace, and 6 tankless water heaters. Air-free concentrations and fuel-based emission factors were determined for carbon monoxide, nitrogen oxides, nitrogen dioxide, and the number of (predominantly ultrafine) particles over complete burns?including transient effects (device warm-up and intermittent firing of burners) following ignition--and during more stable end-of-burn conditions. Formaldehyde was measured over multi-burn cycles. ...

2009-12-01

283

Intrinsic magnetism in Fe doped SnO2 nanoparticles  

International Nuclear Information System (INIS)

Iron doped semiconducting nanoparticles Sn1-xFexO2 with x=0, 0.001, 0.002, 0.003, 0.004, 0.01 and 0.03 were prepared by a sol-gel method. The X-ray diffraction, Transmission Electron Microscopy measurements confirm the rutile structure with no impurity phase. The three characteristic lines of electron spin resonance (ESR) are observed in the doped samples for all compositions, which is a clear evidence for rhombic Fe3+ in rutile phase. The line width of ESR increases with increase in Fe concentration due to induced disorder. The spin-pumping effect is observed at temperatures below 250 K for the samples with x=0.01 and 0.03. However, based on the Curie-Weiss susceptibility, iron is in paramagnetic state and is subject to weak antiferromagnetic interaction. Blue shift in the optical band gap is observed with increase in the Fe content. -- Graphical abstract: The ESR spectra reveal that the nature of Fe in Sn1-xFexO2 samples is isolated rhombic ...

2011-01-01

284

Assessing the Universal Basic Education Primary and Koranic Schools' Synergy for "Almajiri" Street Boys in Nigeria  

Science.gov (United States)

Purpose: The purpose of this paper is to show how Nigeria's current Universal Basic Education on primary schooling targets Muslim "Almajiri" street boys for basic literacy acquisition. The paper examines the policy's management implementation practices and challenges, as well as provides policy options that may minimize discrepancies for effective management. Design/methodology/approach: The discussion is guided by preliminary qualitative studies using phenomenology research philosophy to better understand the social realities of the boys' schooling. Using a descriptive case study approach, two schools in a major city of northern Nigeria served as research sites. Data collection process involved informal interviews, active observations, and discussions with a purpose with four boys, and two teachers as primary participants. Data analysis engaged the generation of themes from the transcribed interview and personal observation field notes, with major ones as ...

2007-12-01

285

TRIGA spent fuel bundles safe storage  

International Nuclear Information System (INIS)

TRIGA-SSR is a steady state research and material test reactor that has been in operation since 1980. The original TRIGA fuel was HEU (highly enriched uranium) with a U"2"3"5 enrichment of 93 per cent. Almost all TRIGA HEU fuel bundles are now burned-up. Part of the spent fuel was loaded and transferred to US, in a Romania - DOE arrangement. The rest of the TRIGA fuel bundles have to be temporarily stored in the TRIGA facility. As the storage conditions had to be established with caution, neutron and thermal hydraulic evaluations of the storage conditions were required. Some criticality evaluations were made based on the SAR (Safety Analysis Report) data. Fuel constant axial temperature approximation effect is usual for criticality computations. TRIGA-SSR fuel bundle geometry and materials model for SCALE5-CSAS module allows the introduction of a fuel temperature dependency for the entire fuel active height, using different materials for each ...

2007-05-13

286

Surface Roughness of Stainless Steel Bender Mirrors for FocusingSoft X-rays  

Energy Technology Data Exchange (ETDEWEB)

We have used polished stainless steel as a mirror substrate to provide focusing of soft x-rays in grazing incidence reflection. The substrate is bent to an elliptical shape with large curvature and high stresses in the substrate require a strong elastic material. Conventional material choices of silicon or of glass will not withstand the stress required. The use of steel allows the substrates to be polished and installed flat, using screws in tapped holes. The ultra-high-vacuum bender mechanism is motorized and computer controlled. These mirrors are used to deliver focused beams of soft x-rays onto the surface of a sample for experiments at the Advanced Light Source (ALS). They provide an illumination field that can be as small as the mirror demagnification allows, for localized study, and can be enlarged, under computer control,for survey measurements over areas of the surface up to several millimeters. The critical issue of the quality of the steel surface, polished and coated with ...

2005-10-11

287

Reduction of RF-sheaths potentials by compensation or suppression of parallel RF currents on ICRF antennas  

International Nuclear Information System (INIS)

Radio frequency (RF) sheaths are suspected of limiting the performance of present-day ion cyclotron range of frequencies (ICRFs) antennas over long pulses and should be minimized in future fusion devices. Within the simplest models, RF-sheath effects are quantified by the integral VRF = ? E|| ? dl where the parallel RF field E|| is linked with the slow wave. On 'long open field lines' with large toroidal extension on both sides of the antenna it was shown that VRF is excited by parallel RF currents j|| flowing on the antenna structure. In this paper, the validity of this simple sheath theory is tested experimentally on the Tore Supra (TS) ITER-like antenna prototype (ILP), together with antenna simulation and post-processing codes developed to compute VRF. The predicted poloidal localization of high-|VRF| zones is confronted to that inferred from experimental data analysis. Surface temperature distribution on ILP front face, as well as ILP-induced modifications of ...

2010-02-01

288

Radiation effects on shoot tip culture of chrysanthemum, 2  

International Nuclear Information System (INIS)

(1) Young chrysanthemums were planted after being irradiated at the time of shoot tip culture and the influence of irradiation was evaluated from the point of view of establishment of mutants. (2) Two cultivars, Kin-tenryu and Tenryu-no-asa were used in this experiment. The percentage of cultivars healthy enough to transplant on June 10, 1972 showed a decrease in proportion to the increase of dosage. Some plants of cultivar Kin-tenryu died after being transplanted. (3) Few plants of either cultivar could overwinter, and in particular no plant irradiated by gamma-rays of 20 kR. (4) Plant height showed a tendency of inhibition in both cultivars. (5) Three chlorophyll mutants showing chimera appeared. One of them was in the cultivar Tenryu-no-asa irradiated by 10 kR at 3 days after planting; two of them were in the cultivar Tenryu-no-asa irradiated by 10 kR at 5 days after planting. One mutant exhibiting malformation of entire leaves appeared in the cultivar ...

289

Nutrient dynamics and carbon partitioning in nutrient loaded Picea mariana [Mill.] B.S.P. seedlings during hardening  

Energy Technology Data Exchange (ETDEWEB)

Biomass and nutrient dynamics of black spruce seedlings during the hardening phase of the greenhouse rotation were examined after four pre-hardening fertilization regimes - conventional, constant-rate loading, exponential loading, and high exponential loading (delivering respectively 15, 40, 40 and 60 mg N seedling{sup -1}) - in order to assess nutrient dilution and steady-state nutrition. Although height growth of seedlings had virtually ceased during hardening, shoot biomass increased 99-142% and root biomass increased five- to tenfold depending on treatment. The biomass increase compromised steady-state nutrient status by diluting internal nutrient pools as nutrient supply was unable to keep up with growth. Soil nutrient levels were rapidly depleted during this period because of plant uptake and lack of fertilizer supplementation. Pre-hardening nutrient loading partly countered and delayed dilution effects, especially when applied ...

1997-07-01

290

Numerical study on the heat transfer to CO_2 flowing upward in a heated vertical tube at supercritical pressure  

International Nuclear Information System (INIS)

Full text of publication follows: As the coolant experiences no phase change in the core, SCWRs, unlike LWRs, cannot use design criteria based on the critical heat flux concept. The commonly accepted practice in SCWRs is to specify cladding temperature limits that must be met during transient and accident events. Therefore for the design of the SCWR, it is very important to predict the heat transfer coefficient to the supercritical water coolant with great accuracy. Our recent study focuses on the critical issue of measuring heat transfer to supercritical water at prototypical SCWR conditions and to develop the tools to predict the SCWR thermal behavior. A heat transfer test loop using a surrogate fluids, CO_2, is under construction. The reason of using CO_2 instead of water is that (i) valuable insight of the physical phenomena can be obtained with this fluid, and (ii) some existing facilities already used surrogate fluids, which in general have lower critical pressure and ...

2005-10-02

291

Heat transfer and fluid dynamics of high heat flux fuel rod for VHTR; Heat transfer augmentation by square ribbed surface  

Energy Technology Data Exchange (ETDEWEB)

Experimental studies on the heat transfer and fluid dynamics of a high heat flux fuel rod for a very high temperature reactor (VHTR) were performed using a single channel test rig of a fuel stack test section (T{sub 1-s}) installed in a helium engineering demonstration loop (HENDEL). The fuel rod has been developed in order to enhance the turbulent heat transfer coefficient than that of the standard fuel rod obtained by the previous experiment. Two-dimensional square ribs were settled on the outer surface of the fuel rod axially to improve the heat transfer. The configuration of a square rib is 0.5 mm in width(w), 0.5 mm in height(h) and 5 mm in pitch(p): p/h=10. The experiment were carried out under the helium gas conditions of high temperature and pressure simulated the VHTR operation. For the turbulent region of Reynolds number 2,500{approx}8,000 of the VHTR core flow condition, it was found that the heat transfer coefficient of the fuel rod and the friction ...

1991-10-01

292

Heat transfer and fluid dynamics of high heat flux fuel rod for VHTR  

International Nuclear Information System (INIS)

Experimental studies on the heat transfer and fluid dynamics of a high heat flux fuel rod for a very high temperature reactor (VHTR) were performed using a single channel test rig of a fuel stack test section (T_1_-_s) installed in a helium engineering demonstration loop (HENDEL). The fuel rod has been developed in order to enhance the turbulent heat transfer coefficient than that of the standard fuel rod obtained by the previous experiment. Two-dimensional square ribs were settled on the outer surface of the fuel rod axially to improve the heat transfer. The configuration of a square rib is 0.5 mm in width(w), 0.5 mm in height(h) and 5 mm in pitch(p): p/h=10. The experiment were carried out under the helium gas conditions of high temperature and pressure simulated the VHTR operation. For the turbulent region of Reynolds number 2,500#approx#8,000 of the VHTR core flow condition, it was found that the heat transfer coefficient of the fuel rod and the friction factor ...

1991-01-01

293

Experimental studies on interactions between a freely propagating flame and single obstacles in a rectangular confinement  

Energy Technology Data Exchange (ETDEWEB)

Experimental investigations were performed to assess the effects of different shaped obstructions on flame propagation in a rectangular confinement, 235 mm in height, with a 1000 x 950mm cross section and a large top-venting area of 1000 x 320mm. Four different single obstacles were used: rectangular, cylindrical, triangular, and square cross-sections with blockage ratios of 5 and 10%. Temporally resolved flame front images were recorded by a high-speed video camera to investigate the interaction between a propagating flame and the obstacle. The local flame displacement speeds and their probability density functions (pdfs) were obtained for the different obstacles. Before the freely propagating flame impinges on the obstacle, the flame propagation speed remains close to the laminar burning velocity, regardless of the obstacles used. As the propagating flame impinges on the obstacle, the local propagation speed increases due to the expansion of ...

2007-07-15

294

Single Molecule Source Reagents for CVD of Beta Silicon Carbide.  

Science.gov (United States)

Beta silicon carbide is an excellent candidate semiconductor material for demanding applications in high power and high temperature electronic devices due to its high breakdown voltage, relatively large band gap, high thermal conductivity and high melting...

1991-01-01

295

Revision number 2 to test design description Volume IB, Part 2 (WHC-SP-0214) FSP-1R FFTF test assembly (HF191A)  

Energy Technology Data Exchange (ETDEWEB)

Based on changes to the fuel pin gas gap composition, pin location and assembly location, revisions to the TDD-IB, Part 2 are provided.

1989-07-14

296

On the temperature dependence of the magnetic excitations  

International Nuclear Information System (INIS)

We compare experimental data for temperature dependence of the magnetic order parameter and the magnetic excitations (spin waves) in materials with a quenched orbital moment and a well-defined spin quantum number. It is observed that the thermal decrease of the two quantities proceeds according to the same analytical function of the type y(T)=1-cT"#epsilon# with an identical exponent #epsilon#. This power function applies not only asymptotically for T->0 but holds over a wide temperature range. The exponent #epsilon# is universal, i.e. independent of spin order type and lattice symmetry and depends only on the dimensionality of the relevant interactions and on whether the spin quantum number is integer or half-integer. The different T"#epsilon# functions are identified as representations of stable universality classes. The fact that order parameter and magnetic excitations follow the same T"#epsilon# function shows that the two quantities belong to the same universality class. The ...

2005-07-15

297

Formation Energies of Antiphase Boundaries in GaAs and GaP: An ab Initio Study  

UK PubMed Central (United Kingdom)

Electronic and structural properties of antiphase boundaries in group III-V semiconductor compounds have been receiving increased attention due to the potential to integration of optically-active III-V...Full Text Available

298

Exploding Bridgewire Electrical System Test Unit.  

Science.gov (United States)

The object of the test was to develop a method to field test the Exploding Bridgewire (EBW) System for proper functioning prior to use. Two basic designs were conceived and tested. The first design using a two element spark gap and a calibrated fuse link ...

1964-01-01

299

Core Synthesis Facility: Bridging the Gap between Chemistry and Biology  

UK PubMed Central (United Kingdom)

CF-23“The biggest stumbling block for biological sciences turned out to be synthetic organic chemistry” – Elias A. Zerhouni, Former NIH Director in Chemical...Full Text Available

2010-09-01

300

Identification of data gaps and research needs for solid wastes from synfuel technologies  

Science.gov (United States)

This report presents an overview of research activity currently being funded by the US Department of Energy (DOE) on solid wastes from coal gasification, coal liquefaction, and oil shale technologies, Projects conducted in the DOE energy technology centers and national laboratories, and in cooperative projects with other government agencies, private industry, and universities are developing the basic and applied technology and data on which present and future fuel-conversion and utilization processes depend. The report identifies data gaps and recommends research needs where warranted.

1982-03-01

301

Grid-controlled plasma cathodes  

International Nuclear Information System (INIS)

Experiments are described on a plasma cathode with biased grids to prevent entry of ions into the electron extraction gap. The cathode has potential applications to the generation of high-current pulsed electron beams. Operation at 20 A/cm"2 is theoretically possible. The source combines the low average power consumption of a plasma cathode with many of the attractive features of thermionic cathodes, such as space-charge-limited extractor gap electron flow, fast turn-on, and no diode closure. Initial experiments are reported at the 2 A/cm"2 level for pulse lengths to 160 #mu#s.

302

Gender gap in maths test scores in South Korea and Hong Kong: Role of family background and single-sex schooling  

British Library Electronic Table of Contents (United Kingdom)

In many industrialised societies, women remain underrepresented in the sciences, which can be predicted by the gender gap in math achievement at school. Using PISA 2006 data, we explore the role of family background and single-sex schooling in girls' disadvantage in maths in South Korea and Hong Kong. This disadvantage is found to be associated with single-sex schooling, but not with family background. Attending a girls' school confers a benefit only in South Korea, whereas the gendered curriculum counteracts the selectivity advantage of girls' schools in Hong Kong. We find that a gendered social structure prevalent in both societies.

2012-01-01

303

GaP Project: #gamma#p, #gamma#e, #gamma##gamma# colliders physical programs and CompHEP computer system  

International Nuclear Information System (INIS)

The Gamma Physics (GaP) program of physical phenomena investigation is proposed on #gamma#p, #gamma#e and #gamma##gamma# colliders at TeV energies. The program contains specialized software (CompHEP system) created for automation of particle interaction processes calculations in the framework of various gauge models. Preliminary physical results are presented (heavy quark production, W, Z production, supersymmetry etc.), and further software development is suggested. (R.P.) 22 refs., 8 figs., 4 tabs.

304

Finite element prediction of differential eddy current probe signals from Fe _30_4 deposits in PWR steam generators  

International Nuclear Information System (INIS)

The paper is concerned with the simulation of practical testing situations which are too difficult and/or expensive to replicate in a laboratory environment. Numerical experiments are described which simulate the differential eddy current probe response to the build-up and chemical flushing of magnetite in the crevice gap of a PWR steam generator unit. The simulation results agree well with the only experimental data available to the authors and lead to the conclusion that conventional differential eddy current probes should be capable of characterizing crevice gap conditions with respect to the presence of magnetite. (author).

1985-01-01

305

Evaluation of Townsend's first ionization and attachment coefficients from prebreakdown current measurements  

International Nuclear Information System (INIS)

Hitherto in this laboratory, ionization coefficients alpha and attachment coefficients #eta# have been determined from Townsend's discharge experiments by a curve-fitting method. However, the method proved to be laborious, Formulae have been derived in this paper to give value of alpha and #eta# as a function of Isubo, Isub1 and Isub2 where Isubo is the photoelectric current at a gap setting d and Isub2 the current at another gap setting 2 d. The values of alpha and #eta# obtained give currents in agreement to within 3% in the best cases with the observed currents.

306

Cysteine-containing peptides having antioxidant properties  

Energy Technology Data Exchange (ETDEWEB)

The term "homology" or "homologous" means an amino acid similarity measured by the program, BLAST (Altschul et al (1997), "Gapped BLAST and PSI-BLAST: a new generation of protein database search programs", Nucleic Acids Res. 25:33 89 3402), and expressed as --(% identity n/n). In measuring homology between a peptide and a protein of greater size, homology is measured only in the corresponding region; that is, the protein is regarded as only having the same general length as the peptide, allowing for gaps and insertions.

2007-05-15

307

Bound and resonant surface states at the (110) surfaces of AlSb, AlAs, and AlP  

Energy Technology Data Exchange (ETDEWEB)

The dispersion curves E(k-bar) have been calculated for bound and resonant (110) surface states of AlSb, AlAs, and AlP. AlSb is predicted to have no surface states within the bulk fundamental band gap, but AlAs and AlP are predicted to have surface state band minima which are very near the conduction band edge, and could lie either within the gap or immediately above the edge.

1982-07-01

308

Structure and electronic studies of defects in amorphous silicon. Final report, March 1980-February 1981  

Science.gov (United States)

Basic research of the structure and electronic properties of a-Si:H is reported with particular emphasis on the role of defects. The main findings are as follows: (1) low defect density material can be deposited at a high rate using SiH/sub 4/ diluted in He or Ne. Using Ar or Kr results in a high defect density and columnar material; (2) an electrical bias during deposition modifies the band gap, hydrogen concentration and structure; (3) the clustering of hydrogen in the regions between the columns is confirmed; (4) hydrogen diffusion is observed by NMR; (5) the oxidation of an a-Si:H surface results in approx. 3 x 10/sup 11/ cm/sup -2/ dangling bonds at the interface; (6) auger recombination of photoexcited carriers is a significant non-radiative mechanism at low temperatures; (7) non-radiative recombination by diffusion and capture at dangling bonds is observed at temperatures above 50 to 100/sup 0/K; (8) the defect density in doped and compensated a-Si:H is ...

1981-08-01

309

Optical properties of crystalline and non-crystalline iron oxide thin films deposited by spray pyrolysis  

International Nuclear Information System (INIS)

Crystalline and non-crystalline iron oxide (#alpha#-Fe_2O_3) thin films were obtained by spray pyrolysis onto glass substrate at different temperatures. The results of X-ray diffraction showed that with increasing the deposition time, the film structure changed from non-crystalline to crystalline at the same substrate temperature. At different substrate temperatures and low deposition times (5 min), iron oxide appears almost in non-crystalline form. With rising the substrate temperature and deposition time, the crystallinity was improved. The effect of substrate temperature as well as deposition time on the optical features (absorption coefficient and bandgap) and optical constants of these films has been investigated. Optical constants of the films were determined from spectrophotometric measurement of reflectance and transmittance. Analysis of the results showed that, for non-crystalline iron oxide films of different thicknesses (76-118 nm) deposited at ...

2004-06-30

310

Optical modeling of compound CuInS{sub 2} using relative dielectric function approach and Boubaker polynomials expansion scheme BPES  

Energy Technology Data Exchange (ETDEWEB)

The ternary compound CuInS{sub 2} is attractive for solar cells due to its band gap of 1.54 eV which borders the optimum value necessary for conversion of a solar spectrum. Recently, works on thin film cells based on this material (ZnO/CuInS{sub 2}) has been reported to show efficiency as high as 11.4%. In this paper, the orientation and the morphology of CuInS{sub 2} sprayed films are determined by the means of X-ray diffraction and scanning electron microscopy. Sprayed CuInS{sub 2} films deposited onto a transparent Pyrex substrate with standard fabrication parameters show a chalcopyrite structure with a preferential orientation (1 1 2). A model based on the calculation of the relative dielectric function {epsilon} has been performed in order to obtain the profile of variation of this parameter and to understand the optical behavior of this material via its transmittance and reflectance in visible and near-infrared regions (0.35-2.5 {mu}m). In the same way, ...

2009-07-29

311

Optical modeling of compound CuInS2 using relative dielectric function approach and Boubaker polynomials expansion scheme BPES  

International Nuclear Information System (INIS)

The ternary compound CuInS2 is attractive for solar cells due to its band gap of 1.54 eV which borders the optimum value necessary for conversion of a solar spectrum. Recently, works on thin film cells based on this material (ZnO/CuInS2) has been reported to show efficiency as high as 11.4%. In this paper, the orientation and the morphology of CuInS2 sprayed films are determined by the means of X-ray diffraction and scanning electron microscopy. Sprayed CuInS2 films deposited onto a transparent Pyrex substrate with standard fabrication parameters show a chalcopyrite structure with a preferential orientation (1 1 2). A model based on the calculation of the relative dielectric function ? has been performed in order to obtain the profile of variation of this parameter and to understand the optical behavior of this material via its transmittance and reflectance in visible and near-infrared regions (0.35-2.5 ?m). In the same way, considering the inhomogeneous material ...

2009-07-29

312

Morphological and thermal properties of {beta}-SnS{sub 2} sprayed thin films using Boubaker polynomials expansion  

Energy Technology Data Exchange (ETDEWEB)

In this work, {beta}-SnS{sub 2} thin films have been prepared on glass substrates by the spray pyrolysis technique using an alcohol solution which contains tin chloride (SnCl{sub 4}) and thiourea (SC(NH{sub 2}){sub 2}) as precursors. The structural study shows that {beta}-SnS{sub 2} thin film prepared using optimal experimental conditions: substrate temperature T{sub s} = 280 deg. C and the concentration ratio of sulfur and tin elements in the spray solution x = [S]/[Sn] = 2.5, crystallizes in the hexagonal phase with a strong (0 0 1) X-ray diffraction line. In the same way, microprobe analyses (EPMA) as well as X-ray photoelectron spectroscopy (XPS) show the presence of undiserable phase of SnO{sub 2}. From the transmission and reflectance spectra, the band gap energy is 2.65 eV. On the other hand, the photothermal properties of such films have been studied, the thermal conductivity was K{sub c} = 0.85 W m{sup -1} K{sup -1} and the thermal diffusivity was D{sub c} ...

2009-05-27

313

Morphological and thermal properties of ?-SnS2 sprayed thin films using Boubaker polynomials expansion  

International Nuclear Information System (INIS)

In this work, ?-SnS2 thin films have been prepared on glass substrates by the spray pyrolysis technique using an alcohol solution which contains tin chloride (SnCl4) and thiourea (SC(NH2)2) as precursors. The structural study shows that ?-SnS2 thin film prepared using optimal experimental conditions: substrate temperature Ts = 280 deg. C and the concentration ratio of sulfur and tin elements in the spray solution x = [S]/[Sn] = 2.5, crystallizes in the hexagonal phase with a strong (0 0 1) X-ray diffraction line. In the same way, microprobe analyses (EPMA) as well as X-ray photoelectron spectroscopy (XPS) show the presence of undiserable phase of SnO2. From the transmission and reflectance spectra, the band gap energy is 2.65 eV. On the other hand, the photothermal properties of such films have been studied, the thermal conductivity was Kc = 0.85 W m-1 K-1 and the thermal diffusivity was Dc = 14.5 x 10-6 m2 s-1. The analysis of ?-SnS2 thin films via the ...

2009-05-27

314

Investigation of thermohydraulic parameters during natural convection cooling of TRIGA reactor  

International Nuclear Information System (INIS)

Important steady-state thermohydraulic parameters of the TRIGA research reactor operating under natural convection mode of coolant flow were investigated using NCTRIGA computer code. Neutronic parameters used in preparing the input of NCTRIGA were taken from the analysis performed by 3-D Monte Carlo code MCNP4C. Benchmarking of the NCTRIGA calculated results were performed against the experimental data measured by the thermocouples in the instrumented fuel element (IFE) during the steady state operation of the reactor under natural convection mode of coolant flow. Various thermohydraulic parameters like the coolant velocity, flow rate and mass flow rate were generated for the hot channel as well as for the two channels comprising instrumented fuels. Calculated peak fuel temperatures at different power levels were compared with the measured values and also with the calculations performed by PARET code. Axial temperature profile at the fuel centreline, fuel surface and coolant in the hot ...

2006-09-01

315

Interface engineering in chalcopyrite thin film solar devices  

Energy Technology Data Exchange (ETDEWEB)

Successful interface engineering requires compositional and electronic material characterization as a prerequisite for understanding and intentionally generating interfaces in photovoltaic devices. The paper gives an overview with several examples, all referring to Cu(In,Ga)(S,Se){sub 2} ('CIGSSe')-based solar cells, with an emphasis on characterization using highly specialized methods, such as elastic recoil detection analysis, X-ray emission spectroscopy and photoelectron spectroscopy using synchrotron and ultraviolet light for excitation, inverse photoemission spectroscopy and Kelvin probe force microscopy. First, the determination of the depth profile of the band gap energy E{sub g} in the absorber layer is demonstrated. The modification of E{sub g} towards both interfaces is discussed in terms of beneficial electronic effects. Next, the interface between absorber and buffer layers with alternative and promising non-toxic ...

2006-06-15

316

Feasibility of maintaining natural convection mode core cooling in research reactor power upgrades  

International Nuclear Information System (INIS)

Two operational concerns for natural convection coooled research reactors using plate type fuels are: 1) pool top "1"6N activity (PTNA), and 2) nucleate boiling in core channels. The feasibility assessment of a power upgrade while maintaining natural convection mode core cooling requires addressing these operational concerns. Previous studies have shown that: a) The conventional technique for reducing PTNA by plume dispersion may not be effective in a large power upgrade of research reactors with small pools. b) Currently used correlations to predict onset of nucleate boiling (ONB) in thin, rectangular core channels are not valid for low-velocity, upward flows such as encountered in natural convection cooling. The PTNA depends on the velocity distribution in the reactor pool. COMMIX-1A code is used to determine the three-dimensional velocity fields in The Ohio State University Research Reactor (OSURR) pool as a function of varying design conditions, following a ...

1988-05-01

317

Environmental benefits and economic rationale of expanding the Italian natural gas private car fleet  

International Nuclear Information System (INIS)

There are several concerns which bring to consider natural gas as a viable alternative to liquid fuels in transport. First, natural gas allows the curbing of global pollution in this steadily growing industry. Indeed, decoupling greenhouse gas emissions from transport growth has become a major issue in tackling climate change. Second, a more extensive use of natural gas would relieve city air quality, which is presently at levels harmful of human health. Nonetheless, this is just one side of the coin. The other side entails building a refuelling station network, and this carries financial requirements. The financing fraction holds a pivotal role in deciding whether natural gas for automotive purposes is an efficient solution. The final aim of this work is, therefore, to compare the natural gas advantages, stemming from avoided global and local emission, with the economic rationale of engaging in supplementary model network investments. A system dynamics model underlies this study's ...

2005-01-01

318

Developing a holistic strategy for integrated waste management within municipal planning: Challenges, policies, solutions and perspectives for Hellenic municipalities in the zero-waste, low-cost direction  

International Nuclear Information System (INIS)

The present position paper addresses contemporary waste management options, weaknesses and opportunities faced by Hellenic local authorities. It focuses on state-of-the-art, tested as well as innovative, environmental management tools on a municipal scale and identifies a range of different collaboration schemes between local authorities and related service providers. Currently, a policy implementation gap is still experienced among Hellenic local authorities; it appears that administration at the local level is inadequate to manage and implement many of the general policies proposed; identify, collect, monitor and assess relevant data; and safeguard efficient and effective implementation of MSWM practices in the framework of integrated environmental management as well. This shortfall is partly due to the decentralisation of waste management issues to local authorities without a parallel substantial budgetary and capacity support, thus ...

2009-05-01

319

Comparing compressed sequences for faster nucleotide BLAST searches.  

Science.gov (United States)

Molecular biologists, geneticists, and other life scientists use the BLAST homology search package as their first step for discovery of information about unknown or poorly annotated genomic sequences. There are two main variants of BLAST: BLASTP for searching protein collections and BLASTN for nucleotide collections. Surprisingly, BLASTN has had very little attention; for example, the algorithms it uses do not follow those described in the 1997 BLAST paper and no exact description has been published. It is important that BLASTN is state-of-the-art: Nucleotide collections such as GenBank dwarf the protein collections in size, they double in size almost yearly, and they take many minutes to search on modern general purpose workstations. This paper proposes significant improvements to the BLASTN algorithms. Each of our schemes is based on compressed bytepacked formats that allow queries and collection sequences to be compared four bases at a time, permitting very fast query evaluation ...

320

Basic study of entire whole-body PET scanners based on the OpenPET geometry  

International Nuclear Information System (INIS)

A conventional PET scanner has a 15-25 cm axial field-of-view (FOV) and images a whole body using about six bed positions. An OpenPET geometry can extend the axial FOV with a limited number of detectors. The entire whole-body PET scanner must be able to process a large amount of data effectively. In this work, we study feasibility of the fully 3D entire whole-body PET scanner using the GATE simulation. The OpenPET has 12 block detector rings with the ring diameter of 840 mm and each block detector ring consists of 48 depth-of-interaction (DOI) detectors. The OpenPET has the axial length of 895.95 mm with five parts of 58.95 mm open gaps. The OpenPET has higher single data loss than a conventional PET scanner at grouping circuits. NECR of the OpenPET decreases by single data loss. But single data loss is mitigated by separating the axially arranged detector into two parts. Also, multiple coincidences are found to be important for the entire ...

2010-09-01

321

Advanced Method for In-Field Measurement, Monitoring and Verification of Total Soil Carbon  

Science.gov (United States)

The Earth`s oceans, forests, agricultural lands and other natural areas absorb about half of the carbon dioxide emitted from anthropogenic sources. Terrestrial carbon sequestration strategies are immediately available to bridge the gap between current terrestrial sequestration capacity and high-capacity geologic sequestration projects available in 10 to 20 years. Terrestrial carbon sequestration strategies consist of implementing land management practices aimed at decreasing CO2 emitted into the atmosphere and developing advanced measurement tools to inventory and monitor carbon processes in soils and biota. In addition to atmospheric CO2 mitigation and carbon trading advantages, terrestrial carbon sequestration produces a variety of benefits which include reclamation of degraded lands, increased soil productivity, increased land value and a more secure food source. Carbon storage in soil depends on climate and management practices, with potential yearly ...

2005-12-01

322

Pulse height response of Si surface barrier detectors to 5-70 MeV heavy ions  

Energy Technology Data Exchange (ETDEWEB)

An extensive series of pulse height measurements have been performed in partially depleted Si surface barrier detectors, using various heavy ions (Li, B, C, O, Al and Cl), at energies between 5 and 70 MeV. After correcting for the small energy loss of the incident ions in traversing the gold surface barrier layer of the detector and for the residual nuclear stopping, the resulting pulse heights per MeV for the various heavy ions were found to be up to 2.5% larger than for the {sup 241}Am (5.486 MeV) alpha particle. This increase, although significant, is smaller than had been anticipated from an extrapolation of the earlier study of H, He and Li pulse heights by Lennard et al.. A new method of analysis of pulse height data, which significantly reduces the uncertainties associated with the dead layer energy loss and nuclear stopping corrections, was used in order to determine directly the variation of ...

1992-04-01

323

Experimental study on two-phase flow regime transition from stratified to slug flow in a large-height horizontal duct  

Energy Technology Data Exchange (ETDEWEB)

The prediction of two-phase flow regime in the horizontal pipings during a loss-of-coolant accident (LOCA) is important for safety analysis of a pressurized water reactor (PWR). The flow regime transition conditions for a horizontal two-phase air-water flow were studied using a large-height, horizontal rectangular duct test section. The duct dimensions were 700 mm in height, 100 mm in width and 28.3 m in length. The experimental criterion for the flow regime transition from the stratified to slug flow regimes, in terms of the local void fraction and the non-dimensional gas-liquid relative velocity, agreed qualitatively with the prediction by the Mishima-Ishii model that is based on an idea that the interfacial waves with the largest growth rate will develop into a slug. However, the transition in the experiment occurred at systematically lower (by about 40 %) relative velocities than the prediction by the Mishima-Ishii model. Therefore, an ...

1992-02-01

324

DMSA scan nomograms for renal length and area: Related to patient age and to body weight, height or surface area  

International Nuclear Information System (INIS)

Aim: To create nomograms for renal size as measured from DMSA renal studies, and to test the nomograms for their ability to separate normal from abnormal kidneys. Method: Renal length was measured from posterior oblique views and renal area from posterior views. Results from 253 patients with bilateral normal kidneys were used to create nomograms for renal size relative to patient age, body height, weight or body surface area (BSA). The nomograms enclosed 95% of the normal kidneys, thus indicating the range for 95% confidence limits, and hence the specificity. Each nomogram was then tested against 46 hypertrophied kidneys and 46 damaged kidneys. Results: The results from nomograms of renal length and renal area, compared to age, body height, body weight and BSA are presented. For each nomogram, the range is presented as a fraction of the mean value, and the number of abnormal kidneys (hypertrophied or damaged) outside the normal range is ...

2002-09-01

325

Carbon monoxide - hydrogen combustion characteristics in severe accident containment conditions. Final report  

International Nuclear Information System (INIS)

Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the combustion threat has received less ...

1994-10-19

326

Tracheal cross-sectional area in children: CT determination  

Energy Technology Data Exchange (ETDEWEB)

A computer method that calculates tracheal cross-sectional area by compensating for partial volume averaging was developed and validated in a study with phantoms. The program was then used to determine the tracheal cross-sectional area of 30 normal children who ranged in age from four months to 18 years. CT-derived cross sections were correlated with age, height, weight, and body-surface area, and they were compared with findings of published clinical and post-mortem studies. CT cross-sectional areas ranged from 20 to 275 mm/sup 2/, varied by as much as 22% at the three different tracheal levels studied, and appeared to correlate most closely with body height. CT-derived tracheal cross-sectional areas are quite similar to those in published reports of postmortem and clinical studies. Measurements of tracheal cross section by CT may prove useful in quantitating tracheal compromise by intrinsic or extrinsic causes.

1983-10-01

327

Simulation study of the influence of the ionospheric layer height in the thin layer ionospheric model  

British Library Electronic Table of Contents (United Kingdom)

This work aims to contribute to the understanding of the influence of the ionospheric layer height (ILH) on the thin layer ionospheric model (TLIM) used to retrieve ionospheric information from the GNSS observations. Particular attention is paid to the errors caused on the estimation of the vertical total electron content (vTEC) and the GNSS satellites and receivers inter-frequency biases (IFB), by the use of an inappropriate ILH. The work relies upon numerical simulations performed with an empirical model of the Earth?s ionosphere: the model is used to create realistic but controlled ionospheric scenarios and the errors are evaluated after recovering those scenarios with the TLIM. The error assessment is performed in the Central and the northern part of the South American continents, a re...

2011-01-01

328

Schottky barrier modulation on silicon nanowires  

Science.gov (United States)

Oxide charge on the sidewalls of SiO{sub 2} embedded silicon wires with 20x20 nm{sup 2} cross section is shown to influence the Schottky barrier height for Pd{sub 2}Si/Si junctions positioned on the end surfaces of the wires. Compared with results on planar silicon surfaces, the electron barrier height is 0.3 eV lower for wires investigated as fabricated. By increasing the oxide charge through irradiation by ultraviolet light, the electron barrier decreases by an additional 0.15 eV and the hole barrier correspondingly increases by about the same amount. The phenomenon is explained by assuming an oxide charge density in the range of 10{sup 12} cm{sup -2}.

2007-03-26

329

Retrieval of chlorophyll a concentration from a fluorescence enveloped area using hyperspectral data  

British Library Electronic Table of Contents (United Kingdom)

It is acknowledged that fluorescence line height (FLH) algorithms are still hampered by the uncertainty of fluorescence peak position. The fluorescence peak moves to longer wavelengths with the increase of chlorophyll a concentration. In this article, the fluorescence enveloped area (FEA), which integrates the fluorescence height and the fluorescence peak position, was used to estimate the chlorophyll a concentration in the coastal waters of the Pearl River Estuary. The FEA algorithm was developed from in situ data of chlorophyll a concentration, total suspended matter (TSM) concentration and above-water remote sensing reflectance, which were collected at 37 sampling stations in the Pearl River Estuary during two cruises. The results showed that the FEA algorithm made a better estimation o...

2011-01-01

330

Long-term changes in graft height after maxillary sinus floor elevation with different grafting materials: radiographic evaluation with a minimum follow-up of 4.5 years  

British Library Electronic Table of Contents (United Kingdom)

Abstract Objective: To compare the vertical dimensional changes with regard to graft height in a long-term follow-up in patients treated with two different grafting materials used in maxillary sinus floor elevation procedures. Material and methods: Twenty consecutive patients were included. One group was grafted with autogenous bone from the mandible (chin area), and the other group was augmented with a 100%b-tricalcium phosphate (b-TCP). During a 4- to 5-year period, in each patient, at least five panoramic radiographs were made. These panoramic radiographs were used for morphometric measurements, at three different locations. The three locations were the first bone to implant contact at the distal side of the second most posterior implant (L1), halfway between this implant and the most p...

2009-01-01

331

Experimental modeling of the explosion mechanism of basaltic magmas  

British Library Electronic Table of Contents (United Kingdom)

Processes in the feeders of basaltic volcanoes during Strombolian-type eruptions were examined with the use of a complex apparatus for modeling basaltic eruptions (CAMBE), which was designed and manufactured by the authors for this purpose. The experimental setup consists of modeling and registering units and has a height of 18 m. It was designed with regard for the geometric dimensions of a natural feeding volcanic system: the ratio of the inner diameter of the feeder to its height is approximately 1: 1000. CAMBE was the first modeling equipment making possible passing a flow of gas-saturated liquid through the conduit, which allowed us to study the nucleation of gas bubbles, their growth, coalescence, transformations of the gas structures, and the kinetics of the gas phase. The experimen...

2009-01-01

332

1991 ice jamming along the Saint John River: a case study  

Energy Technology Data Exchange (ETDEWEB)

Field investigations of major and damaging ice jamming on the Saint John River at Dickey, Maine , and at Sainte-Anne de-Madawaska, New Brunswick, in 1991, were described. The investigations included measurement of water surface profiles and shear wall heights at both sites. The measurements were supplemented by information from local observers and data collection agencies. Using a simplified equilibrium analysis, ice jam thickness and water level at the Dickey site was found to be generally in agreement with observed values. At Sainte-Anne-de-Madawaska sufficient data was obtained to construct and calibrate the numerical model RIVJAM which determined the configuration of the jam in nonequilibrium reaches. Use of the model enabled the successful reproduction of a measured water profile along the jam and the prediction of the approximate thickness of the jam, which was generally less than the measured shear wall height. 14 refs., 11 figs.

1996-04-01

333

The effects of a calcium deficient diet on the mechanical properties and morphology of goose bone.  

Science.gov (United States)

A control group of geese (Anser anser) on a normal calcium diet for egg laying poultry was compared to egg laying geese on a calcium deficient diet. The ultimate compressive strength and modulus of elasticity of femoral cortical bone from each group were determined by compressing right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The bending strength and bending modulus of elasticity of tibial cortical bone were determined by three point bend tests on rectangular prisms which were approximately 25 mm by 0.8 mm by 0.8 mm. Bone calcium content and eggshell calcium content were determined by atomic absorption spectrophotometry. Blood samples were analyzed for free calcium ion concentration. Histological observations included studies of cross-sectional microradiographs, examinations of cross sections stained by a modified Masson's technique, and a determination of fractional area of voids by quantitative microscopy. The average compressive ...

1986-01-01

334

Crack growth behaviour of low alloy steels for pressure boundary components under transient light water reactor operating conditions (CASTOC)  

Energy Technology Data Exchange (ETDEWEB)

The CASTOC project addresses environmentally assisted cracking (EAC) phenomena in low alloy steels used for pressure boundary components in both Western type boiling water reactors (BWR) and Russian type pressurised water reactors (VVER). It comprises the four work packages (WP): inter-laboratory comparison test (WP1); EAC behaviour under static load (WP2), EAC behaviour under cyclic load and load transients (WP3); evaluation of the results with regard to their relevance for components in practice (WP4). The use of sophisticated test facilities and measurement techniques for the on-line detection of crack advances have provided a more detailed understanding of the mechanisms of environmentally assisted cracking and provided quantitative data of crack growth rates as a function of loading events and time, respectively. The effect of several major parameters controlling EAC was investigated with particular emphasis on the transferability of the results to components ...

2004-07-01

335

The influence of copper and chromium on the semiconducting behaviour of passive films formed on weathering steels  

Energy Technology Data Exchange (ETDEWEB)

The influence of small amounts of alloying elements (0.36% Cu and 0.47% Cr) on the semiconducting properties of passive films formed on weathering steels was investigated either in tetraborate/boric acid buffer solution (pH 9.2) or artificial atmospheric environment (SO{sub 2}-containing environment). The electrochemical behaviour was assessed by potentiodynamic polarisation, capacitance measurements and photoelectrochemistry. The chemical characterisation of the films was carried by Auger electron spectroscopy. The polarization results obtained in the buffer solution show that the addition of chromium decreases the passive current density. The capacitance results show that the films behave as an n-type semiconductor with shallow and deep donor levels situated in the forbidden gap. The presence of copper seems to affect the density of the shallow and of the deep donor levels in the forbidden gap, and as chromium, it also decreases the doping ...

2006-12-05

336

The influence of copper and chromium on the semiconducting behaviour of passive films formed on weathering steels  

International Nuclear Information System (INIS)

The influence of small amounts of alloying elements (0.36% Cu and 0.47% Cr) on the semiconducting properties of passive films formed on weathering steels was investigated either in tetraborate/boric acid buffer solution (pH 9.2) or artificial atmospheric environment (SO_2-containing environment). The electrochemical behaviour was assessed by potentiodynamic polarisation, capacitance measurements and photoelectrochemistry. The chemical characterisation of the films was carried by Auger electron spectroscopy. The polarization results obtained in the buffer solution show that the addition of chromium decreases the passive current density. The capacitance results show that the films behave as an n-type semiconductor with shallow and deep donor levels situated in the forbidden gap. The presence of copper seems to affect the density of the shallow and of the deep donor levels in the forbidden gap, and as chromium, it also decreases the doping density ...

2006-12-05

337

Structural, electronic and energetic properties of silicon carbon alloys  

International Nuclear Information System (INIS)

We studied the influence of alloying on the structural and electronic properties of the unrelaxed and relaxed Si_1_-_yC_y random alloys by means of ab initio theoretical calculations using two methods: (i) a supercell approach in connection with the plane-wave pseudopotential method; (ii) the full-potential augmented plane-wave plus local orbitals (APW+lo) method. The first method is used to obtain the relaxed atomic structure. The relaxed atomic positions obtained by pseudopotential calculations were used to calculate the band structure via the second method. The local density approximation was used for the exchange and correlation energy density functional. We investigated the lattice parameters and band gap energies. We found that a quite smaller gap appears in the neighborhood of y=0.03125 concentration of C atoms. The band gap shows a large anomalous bowing and is strongly composition dependent. The electron densities ...

2007-01-15

338

Remodeling of the free electron laser with the L-band linac at Osaka University  

International Nuclear Information System (INIS)

The far infrared free electron laser (FEL) has been being developed since 1990 using the L-band electron linac at the Institute of Scientific and Industrial Research, Osaka University. The first lasing was obtained in 1994 at wavelengths from 32 to 40 #mu#m. The FEL is now being modified suitable for user experiments. The wiggler with a fixed magnet gap used in the original FEL has been remodeled to make the magnet gap variable. In order to optimize the variable range of the gap, the gain and the diffraction loss were calculated. The peak gain is calculated to be 270% and the diffraction loss to be 22% at 150 #mu#m. The wavelength is expected to be variable from 25 up to at least 150 #mu#m. The two bending magnets in the optical resonator have been remodeled and the vacuum chambers with larger vertical sizes for them have been newly made so that the diffraction loss in these parts becomes smaller than that in the vacuum ...

1997-02-28

339

On the band gap dependence of refractive indices of some quaternary III-V and II-VI compounds of device interest  

International Nuclear Information System (INIS)

The credibility of the model proposed by Ghosh in predicting the refractive indices of mixed semiconductor crystals of technological importance within their miscibility range as a function of band gap is demonstrated. The high-frequency refractive indices of four quaternary alloys Al_xGa_1_-_x_-_yIn_yP (y = 0.49, 0 #<=# x #<=# 0.51), InSb_xAs_1_-_x_-_yP_y (y = 2.2x, 0 #<=# x #<=# 0.313, 0 #<=# y #<=# 0.638), Cd_xZn_1_-_x_-_yHg_ySe (x + y = 1, 0.153 #<=# x #<=# 0.684, 0.316 #<=# y #<=# 0.847), and CdS_1_-_x_-_ySe_xTe_y (x + y = 1, 0.15 #<=# x #<=# 0.93, 0.07 #<=# y #<=# 0.85) are calculated according to the relation n"2-1 = A/(E_g + B)"2 where A is an energy gap dependent constant and B is a constant depending on crystal ionicity. The calculated values show excellent agreement with the experimental data thus justifying the validity of the model.

340

Omni-directional gap of 1-D photonic crystals based on porous silicon with a Gaussian profile refractive index  

Energy Technology Data Exchange (ETDEWEB)

Using the transfer matrix method we calculate the omni-directional band gap of a 1-D photonic crystal consisting of alternating layers of two dielectric materials A and B with refractive index n{sub A} and n{sub B}, respectively. The refractive index of layer A is constant and the refractive index of layer B varies according to the envelope of a Gaussian function. We find that under certain circumstances it is possible to obtain 100% reflectivity for both polarizations and any value of the incident angle of the electromagnetic waves. Although the structure considered does not posses a higher omni-directional band gap than the periodic sequence of low and high constant refractive indexes, it can be used to produce a new type of omni-directional mirrors without abrupt interfaces. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

2007-07-01

341

Evaluation of structural integrity of crossover leg piping system with dynamic whip restraints  

Energy Technology Data Exchange (ETDEWEB)

Interference between the crossover leg of the Reactor Coolant System(RCS) and the Pipe Whip Restraints(PWR) has brought a degradation issue of the integrity of the Reactor Coolant System in Westinghouse type Nuclear Power Plants(NPPs) of Korea. According to the gap inspection carried out during planned overhaul (year 2000), interference between the crossover leg and the PWR was found in each RCS loop. This plant has had the high vibration problem on the RC pump 'B'. The reason for the high vibration in the RC pump 'B' had been massively surveyed and it was found that the crossover leg of RCS contacted with the PWR in hot condition. Since the contact between the crossover leg and the PWR changes the dynamic characteristics of the piping system for the RCS, this is considered as one reason for the high vibration. And a possibility of overstress on the crossover leg due to the contact with the PWR should be evaluated. Through ...

2001-07-01

342

Effectively managing nuclear risk through human performance improvement  

International Nuclear Information System (INIS)

Full text: The US commercial nuclear industry has just completed an outstanding decade of plant performance. Safety levels and electric production are at unprecedented high levels and continue to exceed even high industry goals. Nuclear energy continues to keep the highest priority on performance improvement programs and highly trained/qualified people that maintain its record setting safety and reliability of operations. While the industry has maintained a consistently high level of performance, the advent of deregulation and the consolidation of NPP ownership, as well as the current climate of concern about both rising energy costs and availability of power, has raised the standard for nuclear energy's level of competitiveness in today's market place. The resulting challenge is how to more effectively manage risk and improve performance even further in a generally high performing organization. Newer technology and more training by themselves are not the answer. ...

343

Evolution of improved varieties of sesame through induced mutations  

International Nuclear Information System (INIS)

Sesame varieties/genotypes showed a good response to radiation with gamma rays and treatments with EMS. In M_1 both gamma rays and EMS influenced germination, seedling height, survival of plants and pollen fertility/sterility, producing deleterious effects on these characters. Compared to black seeded genotypes, white seeded ones are more susceptible to radiation. Both gamma rays and EMS produced various types of morphological variations in M_2 generation. These were dwarf plant mutants, mottled and fleshy leaved mutants (sterile), fasciated stem, flower colour, altered phyllotaxy, early, uniculm, capsule size variations, multiple capsule/leaf axil, seed coat colour variations, indehiscent and semi-indehiscent type mutants. Moreover, studies on quantitative characters including seed yield revealed the induction of mutants in both positive and negative directions for such traits which made a good scope of selection of desirable mutants in M_2 ...

2001-01-01

344

Character and Effective Leadership of the Knowledge Worker  

Energy Technology Data Exchange (ETDEWEB)

Ulrich in the forward to the Zenger and Folkman (2002) book, ''The Extraordinary Leader'', wrote about the importance of character in leadership stating, ''Everything about great leaders radiates from character. Character improves the probability of exhibiting strong interpersonal skill. Some of this perceived character is innate . . . but more is driven by the leader's self-awareness and interactions with others'' (p. ix). The purpose of this study was to explore the relationship between leadership effectiveness and character using leader-managers of knowledge workers as the subject sample. Findings indicated that character, particularly those factors associated with honesty, setting the example, and valuing and strengthening others, were what set the most effective leader-managers apart from their peers. Technical competence and self-efficacy were found to be ...

2005-04-20

345

Surface-water-resources information for the Ho-Chunk Nation lands and vicinity, Wisconsin  

Science.gov (United States)

The Ho-Chunk Nation is interested in documenting water-quality conditions in streams adjacent to their Reservation lands in Wisconsin and developing management plans to protect these water resources. The Nation uses these waterways for recreation and as a source for food, and therefore, is dedicated to maintaining and restoring their quality. Ho-Chunk lands encompass more than 10,000 acres ranging primarily over 17 counties in Wisconsin. The study areas for this report include streams adjacent to Ho-Chunk Nation residential lands: Potch-Hah-Chee, Sandpillow, Mission, Bluewing, Chakh Hah Chee, Winnebago Heights, Indian Heights, and Ho-Chunk Village. These residential areas, or housing sites, are located along or near the Middle Branch Embarrass, Black, Lemonweir, and Wisconsin Rivers or their tributaries. Water-quality data were compiled and summarized, and basin maps showing land cover and previous sampling sites are presented. Qualitative ...

2003-01-01

346

Quantitative Trait Loci for Grain Yield and Adaptation of Durum Wheat (Triticum durum Desf.) Across a Wide Range of Water Availability  

UK PubMed Central (United Kingdom)

Grain yield is a major goal for the improvement of durum wheat, particularly in drought-prone areas. In this study, the genetic basis of grain yield (GY), heading date (HD), and plant height (PH) was...Full Text Available

2008-01-01

347

NLDAS_MOS0125_H.A20021020.1100.002.grb.xml - NASA  

Science.gov (United States)

Oct 20, 2002 ... ASNOWsfc_sfc_forecastTimeUnit 1 ASNOWsfc_sfc_gridSize 0 ASNOWsfc_sfc_height 0 ASNOWsfc_sfc_level 1 ASNOWsfc_sfc_max 1.9312 kg/m^2 ...

348

Mean wind field in the urban atmospheric boundary layer by sodar data  

Energy Technology Data Exchange (ETDEWEB)

Two-year uninterrupted sodar measurements of vertical profiles of wind speed and direction in the height range 40 to 250-500 m were carried out in two points of Moscow megalopolis. Seasonal and diurnal courses of mean speed profiles, wind speed distributions, wind roses and occurrence of strong and weak wind speed events are shown. Influence of urban heat island and orography on wind field is discussed.

2008-05-01

349

Irradiation test program for FFTF  

International Nuclear Information System (INIS)

Four unique deisgn features are described which make the Fast Flux Test Facility eminently suitable for irradiation test programs. These features are a fast flux level of 7 x 10"1"5 neutrons/cm"2/sec, a 36-inch reference (breeder reactor) core height, test volumes suitable for testing of statistical quantities of materials, and the capability for direct (contact) or indirect (proximity) instrumentation of active core experiments.

350

Induced mutation in Lupinus mutabilis sweet in Peru  

International Nuclear Information System (INIS)

Mutagenesis of Lupinus mutabilis was started at the UNA LM (Peru) to obtain mutants with low alkaloid content and early germination. Varieties SCG 25 and Lib 020 were irradiated with gamma radiation. The optimum dose for the SCG 25 variety was 15 Krad and for Lib 020 15 to 20 Krad. The relation between the plant height and radiation dose fits the quadratic polynomial model.

1984-04-01

351

Fluidic pumps  

International Nuclear Information System (INIS)

A fluidic pump comprises a two-diode pump having a first displacement vessel, a third diode connected to receive output from the two-diode pump through a delivery line and discharge to an outlet, and a second displacement vessel connected to the delivery line. There is a feed tank at a greater height than the two-diode pump, and a drive unit for alternately pressurising and venting the first and second displacement vessels. The drive pressure required to operate the pump can be of the order of half that for a single stage 2-diode pump. (author).

1988-05-19

352

Diffusion absorption heat pump. Diffusion-Absorptions-Waermepumpe  

Energy Technology Data Exchange (ETDEWEB)

The development of a gas-operated diffusion absorption heat pump for the heating of living spaces is described. By various improvement an energy efficiency of the prototypes of 1.5 was achieved. Structural alterations led to a lower overall height and lower production costs. The CFCs used in electric heat pumps were replaced by environmentally neutral ammonia. Compared with conventional gas heating systems, the CO2 output could be reduced by more than 30%. figs., tabs.

1992-02-01

353

Addendum to the 1996 Gunnison Monitoring Report for the Gunnison, Colorado Wetlands Mitigation Plan  

Energy Technology Data Exchange (ETDEWEB)

This document is an addendum to the 1996 Gunnison Monitoring Report for the Gunnison, Colorado, Wetlands Mitigation Report, dated July 1997. The purpose of this addendum is to: (1) modify how information on plant height and plant species criteria are presented; and (2) provide more detailed information regarding the evaluation of the bare ground criteria at the Camp Ketle site. The information in this addendum is provided at the request of the Bureau of Land Management to aid in future monitoring and evaluation of the wetland mitigation sites.

1997-10-01

354

Transverse Imaging of the Proton in Exclusive Diffractive pp Scattering  

Energy Technology Data Exchange (ETDEWEB)

In a forthcoming paper we describe a new approach to rapidity gap survival (RGS) in the production of high-mass systems (H = dijet, Higgs, etc.) in exclusive double-gap diffractive pp scattering, pp -> p + H + p. It is based on the idea that hard and soft interactions are approximately independent (QCD factorization), and allows us to calculate the RGS probability in a model-independent way in terms of the gluon generalized parton distributions (GPDs) in the colliding protons and the pp elastic scattering amplitude. Here we focus on the transverse momentum dependence of the cross section. By measuring the ''diffraction pattern'', one can perform detailed tests of the interplay of hard and soft interactions, and even extract information about the gluon GPD in the proton from the data.

2006-04-20

355

The difference between standard and average efficiencies of multijunction compared with single-junction concentrator cells  

Energy Technology Data Exchange (ETDEWEB)

The theoretical performance of ideal single- and multijunction cells are compared at 100xconcentration under a range of cloudless-sky conditions. The sensitivities of device performance to cell temperature and spectral variations are shown to depend on the number of junctions (one, two or three), the way in which the junctions are connected (series, parallel or independent), and the band gaps of the devices. The average performances of all of the multijunction devices surpass that of a single-junction GaAs device, but the inconsistency in performance of some of the multijunction devices is significant for large variations in cell temperature and incident spectrum. The choice of band gap and connection scheme is more important than the number of junctions in determining the consistency of device performance. (orig.).

1991-05-01

356

Supply chain networks and service-dominant logic: suggestions for future research  

British Library Electronic Table of Contents (United Kingdom)

Purpose - The service-dominant (S-D) logic views supply chains as value co-creation networks. These networks promote knowledge growth amongst network members via resource deployment and coordination. The exchange of knowledge and utilization of operant resources among the network members leads to co-created service offerings and value proposals for the end-users, with the ultimate goal of transforming end-user experiences to perceptions of superior value-in-use. The purpose of this paper is to develop an illustration of the value co-creation concept and use this illustration as guide to examine the research gaps that are yet to be tapped in the area where supply chain networks and S-D logic intersects. Design/methodology/approach - The literature on S-D logic is reviewed and research gaps ...

2011-01-01

357

Soliton microdynamics and thermal conductivity of uranium nitride at high temperatures  

British Library Electronic Table of Contents (United Kingdom)

The microdynamics of soliton waves and localized modes of nonlinear vibrations of the acoustic and optical types in uranium nitride has been investigated. It has been shown that, with an increase in the excitation energy in the spectral gap between the bands of optical and acoustic phonons, the energies of solitons increase, whereas the energies of local modes decrease. The previously experimentally observed unidentified quasi-resonant features, which shift in the gap with variations in the temperature, can represent the revealed soliton waves and local modes. The microdynamics of heat conduction of uranium nitride has been studied for the stochastic generation of soliton waves and local modes in the case of spatially distant energy absorption. The thermal conductivity coefficient determin...

2011-01-01

358

Overview of long-term fuel inventory and co-deposition in castellated beryllium limiters at JET  

International Nuclear Information System (INIS)

Morphology of castellated Be tiles from the belt limiter exposed to the JET plasma for 56,000 s was examined on both sides of castellated grooves, on plasma-facing and side surfaces of the tiles. The essential results are (i) deuterium retention in the castellated grooves and in other locations is associated with co-deposition of carbon; (ii) the decay length of deposition in the castellation is around 1.5 mm; (iii) no deuterium is detected in bulk Be; (iv) bridging of gaps by molten beryllium occurred but gaps were not filled with Be; (v) on side surfaces of the tiles the formation of BeO layer was detected at a distance of 20 mm and more from the plasma-facing surface. The consequences for a long-term operation of a reactor-class device with several different plasma-facing materials are addressed.

2009-04-30

359

Interface-induced conversion of infrared to visible light at semiconductor interfaces  

International Nuclear Information System (INIS)

Efficient, low-temperature conversion of infrared light into visible light (red, orange, green) is reported at single heterojunctions and undoped quantum wells of GaAs and ordered Al_xGa_1_-_xInP_2; an increase in photon energy of 700 meV is obtained. The signal originates from the high-band-gap layers and disappears only if the excitation energy is tuned below the GaAs band gap. The intensity of the up-converted photoluminescence (PL) is found to decrease significantly slower with increasing temperature than that of the regular PL and it remains observable up to 200 K. Interface-induced cold Auger processes along with the presence of trapped states for both electrons and holes in these ordered alloys account for this nonlinear mechanism. A colinear double-beam experiment confirms this. copyright 1996 The American Physical Society.

360

Improvement in the spectral response at long wavelength of a-SiGe:H solar cells by exponential band gap design of the i-layer  

Energy Technology Data Exchange (ETDEWEB)

A new band gap profile (exponential profile) for the active layer of the a-SiGe:H single junction cell has been designed and experimentally demonstrated. In this paper we compare its optical and electrical characteristics with the two more common profiles: the U- and V-shapes. As predicted by the simulations, the new profile combines the advantages of both profiles. Like the V-shape, the exponential shape reduces the amount of Ge in the i-layer, decreasing both the space charge defect density inside the i-layer and the recombination losses. It also improves the electric field. At the same time, the exponential shape generates the same current density as the U-shape.

2002-04-01

361

Energy Management Action Network (EMAK). A scoping study investigating the establishment and support of an international and domestic action network of energy management in industry. Information paper  

Energy Technology Data Exchange (ETDEWEB)

The IEA has identified energy efficiency as essential to achieving a sustainable energy future. In order to improve energy efficiency in industry one of the priority areas for further action is the promotion of more and higher quality energy management (EM) activity. However, there are significant gaps in the current implementation of EM. One method of bridging these gaps would be the creation of an EM Action NetworK (EMAK) to bring practical support to energy managers, connect energy managers to energy policy makers, and interconnect these networks globally. The paper describes possible aims, activities, scope, structure, timelines and approaches related to EMAK and looks at specific tasks that would be important in the set-up and implementation.

2009-12-15

362

Electronic structures of platinum group elements silicides calculated by a first-principle pseudopotential method using plane-wave basis  

Energy Technology Data Exchange (ETDEWEB)

The electronic structures of platinum group elements (Ru, Os, Rh, Ir, Pd, and Pt) silicides have been calculated. Ir{sub 3}Si{sub 5} is a semiconductor with the direct gap of 1.14 eV. Among monosilicides, RuSi and OsSi with the FeSi-type structure are semiconductors with the gap values of 0.21 and 0.41 eV but RhSi, IrSi, PdSi, and PtSi with the MnP-type structure are metals. No semiconducting compounds can be found in other platinum group elements silicides other than known Ru{sub 2}Si{sub 3}, Os{sub 2}Si{sub 3}, and OsSi{sub 2}.

2006-06-29

363

Electronic structures of platinum group elements silicides calculated by a first-principle pseudopotential method using plane-wave basis  

International Nuclear Information System (INIS)

The electronic structures of platinum group elements (Ru, Os, Rh, Ir, Pd, and Pt) silicides have been calculated. Ir_3Si_5 is a semiconductor with the direct gap of 1.14 eV. Among monosilicides, RuSi and OsSi with the FeSi-type structure are semiconductors with the gap values of 0.21 and 0.41 eV but RhSi, IrSi, PdSi, and PtSi with the MnP-type structure are metals. No semiconducting compounds can be found in other platinum group elements silicides other than known Ru_2Si_3, Os_2Si_3, and OsSi_2.

2006-06-29

364

Capacity-coupled multidischarge for atmospheric plasma production  

International Nuclear Information System (INIS)

We propose a method of plasma production by capacity-coupled multidischarge (CCMD) at atmospheric pressure. The discharge gaps in the CCMD consist of a common electrode and a number of compact electrodes (CCE) which are directly coupled with small capacitors for quenching the discharge. A simple CCE structure is provided by a cylindrical capacitor, the inner conductor of which is used as a gap electrode. A short pulse discharge is observed to appear homogeneously at each CCE. A charge transfer for the single-pulsed discharge is 10-100 times as large as that of the conventional dielectric barrier discharge. A high efficiency of ozone production has been confirmed in the CCMD using O_2 gas. A device configuration of the CCMD is quite flexible with respect to its geometrical shape and size. The CCMD could be used to produce plasmas for various kinds of industrial applications at atmospheric pressure.

2003-12-29

365

An evaluation of the UK skills base for toxicologists and ecotoxicologists, with focus on current and future requirements, particularly with regard to the skills required for hazard assessment of chemical substances including nanomaterials  

Environmental Research Database

Objectives1. To establish the present capacity and capability across all the sectors within the UK for - a) Undertaking research in the areas of toxicology and ecotoxicology and environmental hazard and risk assessment work on chemical subtances including emerging containments (e.g. enginerred nanomaterials); and b) Applying these skills in the policy and regulatory context. 2) The range of chemicals involved should include pharmaceutical and medical products, crop protection agents, biocides, vet [continued...]DescriptionThe aim of this project is to identify the current status of the scientific community, areas of expertise, and identify the gaps in skills, knowledge or recruitment. The project will use a questionnaire approach to obtain this information for all sectors of the business community. The analysis will identify the gaps in provision, and areas where investment is needed in future training and/or recruitment.

2009-01-15

366

Achieving a vanishing SNR-gap to exact lattice decoding at a subexponential complexity  

CERN Document Server

The work identifies the first lattice decoding solution that achieves, in the general outage-limited MIMO setting and in the high-rate and high-SNR limit, both a vanishing gap to the error-performance of the (DMT optimal) exact solution of preprocessed lattice decoding, as well as a computational complexity that is subexponential in the number of codeword bits. The proposed solution employs lattice reduction (LR)-aided regularized (lattice) sphere decoding and proper timeout policies. These performance and complexity guarantees hold for most MIMO scenarios, all reasonable fading statistics, all channel dimensions and all full-rate lattice codes. In sharp contrast to the above manageable complexity, the complexity of other standard preprocessed lattice decoding solutions is shown here to be extremely high. Specifically the work is first to quantify the complexity of these lattice (sphere) decoding solutions and to prove the surprising result that the complexity ...

2011-01-01

367

A computational study of aluminum phosphide nanotubes  

British Library Electronic Table of Contents (United Kingdom)

Abstract Electronic structures of two representative zigzag and armchair models of aluminum phosphide nanotube (AlPNT) were investigated by density functional theory calculations. The structures were optimized and the bond lengths, tip diameters, band gaps, and dipole moments were calculated. Moreover, the quadrupole coupling constants (CQ) were calculated for the Al-27 atoms of the optimized structures. The same values of AlP bond lengths were calculated for both models. The larger value of band gap of armchair model than the zigzag model indicated the stronger dielectric property for the former model. The values of CQ(27Al) were the largest for the Al atoms placed at the tips of both zigzag and armchair AlPNT than other Al atoms, which could reveal dominant role of the Al atoms placed at...

2011-01-01

368

Steady-state and transient photoconductivity in c-axis GaN nanowires grown by nitrogen-plasma-assisted molecular beam epitaxy  

International Nuclear Information System (INIS)

Analysis of steady-state and transient photoconductivity measurements at room temperature performed on c-axis oriented GaN nanowires yielded estimates of free carrier concentration, drift mobility, surface band bending, and surface capture coefficient for electrons. Samples grown (unintentionally n-type) by nitrogen-plasma-assisted molecular beam epitaxy primarily from two separate growth runs were examined. The results revealed carrier concentration in the range of (3-6)x10"1"6 cm"-"3 for one growth run, roughly 5x10"1"4-1x10"1"5 cm"-"3 for the second, and drift mobility in the range of 500-700 cm"2/(V s) for both. Nanowires were dispersed onto insulating substrates and contacted forming single-wire, two-terminal structures with typical electrode gaps of #approx =#3-5 #mu#m. When biased at 1 V bias and illuminated at 360 nm (3.6 mW/cm"2) the thinner (#approx =#100 nm diameter) nanowires with the higher background doping showed an abrupt increase in photocurrent ...

2010-02-01

369

Aespoe Task Force on modelling of groundwater flow and transport of solutes. Review of Task 6C  

Energy Technology Data Exchange (ETDEWEB)

This report forms part of an independent review of the specifications, execution and results of Task 6 of the Aespoe Task Force on Modelling of Groundwater Flow and Transport of Solutes, which is seeking to provide a bridge between site characterization (SC) and performance assessment (PA) approaches to solute transport in fractured rock. The present report is concerned solely with Task 6C, which relates to the construction and parametrisation of a block-scale hydrostructural model of the TRUE Block Scale region of the Aespoe Hard Rock laboratory. The task objectives, specifications and outcome are summarised and reviewed. Also, consideration is given to how the hydrostructural model might affect the outcomes of Task 6D and 6E. The main conclusions of this review are summarised below: The Task 6C hydrostructural model is a more comprehensive approach to quantitatively describing a volume of fractured rock than has been achieved hitherto. The idea of including solute retention ...

2005-03-01

370

An emerging field of high-velocity friction and its implication for dynamic fault motion during large earthquakes  

Science.gov (United States)

In order to understand not only the mechanisms of earthquakes, but also the origin of diverse behavior of faults and plate boundaries, one must integrate (1) field studies on faults to understand deep intrafault processes, (2) laboratory work to reproduce those processes and determine mechanical and transport properties of fault zones, (3) theoretical and numerical studies analyzing fault motion, including earthquake generation processes, based on the constitutive properties determined by laboratory studies, and (4) seismological and geodetic studies revealing dynamic fault motion during earthquakes and diverse aseismic fault behavior. Ideally, such integrated studies should be carried out for a selected fault that produced an earthquake with good seismic/geodetic records so the prediction from (1) to (3) can be fully tested with (4), rather than selecting favorite data in the literature. Present session is organized to promote such integrated fault and earthquake studies. This ...

2004-12-01

371

Feasibility study for use of the natural convection shutdown heat removal test facility (NSTF) for VHTR water-cooled RCCS shutdown  

International Nuclear Information System (INIS)

In summary, a scaling analysis of a water-cooled Reactor Cavity Cooling System (RCCS) system was performed based on generic information on the RCCS design of PBMR. The analysis demonstrates that the water-cooled RCCS can be simulated at the ANL NSTF facility at a prototypic scale in the lateral direction and about half scale in the vertical direction. Because, by necessity, the scaling is based on a number of approximations, and because no analytical information is available on the performance of a reference water-cooled RCCS, the scaling analysis presented here needs to be 'validated' by analysis of the steady state and transient performance of a reference water-cooled RCCS design. The analysis of the RCCS performance by CFD and system codes presents a number of challenges including: strong 3-D effects in the cavity and the RCCS tubes; simulation of turbulence in flows characterized by natural circulation, high Rayleigh numbers and low Reynolds numbers; validity ...

372

Tidal spin-up and magnetic braking in cataclysmic variables  

International Nuclear Information System (INIS)

Based on proposed models for the tidal spin-up and magnetic braking of stars with a convective outer envelope, it is suggested that the rotation of secondaries in cataclysmic variables is not necessarily synchronized with the orbital revolution. This may provide an explanation for the observed large range in the mass transfer rate (at the same orbital period) of cataclysmic variables above the period gap. (author).

373

Structural transformation and superconductivity in A-15 compounds  

International Nuclear Information System (INIS)

The correlation between superconductivity and structural transformation in the A-15 compounds are examined in a unified way on the basis of the Gor'kov three-dimensional model and the anisotropic pairing interaction. The temperature dependence of the elastic modulus, the strain order parameter and the energy gaps of superconductivity are obtained and compared with the experimental data. (auth.).

374

Solar receiver enclosure enhancement by controlled directional scattering  

Energy Technology Data Exchange (ETDEWEB)

The interest in efficient solar collector design has stimulated investigation of two-dimensional (trough-like) cavity structures. A novel principle for designing cavity enclosures is described. The present method maintains high transmission albeit at the expense of some concentration in the presence of gaps as large as the radius between reflector and receiver. The new method can be applied to advantage to nonimaging concentrator design as well as to line focus concentrators.

1980-01-01

375

Review of fission product yields and delayed neutron data for the actinides Np-237, Pu-242, Am-242m, Am-243, Cm-243 and Cm-245  

Energy Technology Data Exchange (ETDEWEB)

A review of fission product yields and delayed neutron data for Np-237, Pu-242, Am-242m, Am-243, Cm-243 and Cm-245 has been undertaken. Gaps in understanding and inconsistencies in existing data were identified and priority areas for further experimental, theoretical and evaluation investigation detailed. (author)

1991-07-01

376

Review of fission product yields and delayed neutron data for the actinides Np-237, Pu-242, Am-242m, Am-243, Cm-243 and Cm-245  

International Nuclear Information System (INIS)

A review of fission product yields and delayed neutron data for Np-237, Pu-242, Am-242m, Am-243, Cm-243 and Cm-245 has been undertaken. Gaps in understanding and inconsistencies in existing data were identified and priority areas for further experimental, theoretical and evaluation investigation detailed. (author)

1990-11-06

377

Results for the structural properties of random heaps of hard disks  

Energy Technology Data Exchange (ETDEWEB)

The average angle of repose and the packing density of random planar heaps of hard disks falling ballistically onto a sticky base line, where the first layer of disks is quenched in random positions, are computed for heaps with a small fixed number of gaps in the base layer. The results we find appear to be almost independent of the size of the heap and they agree with those obtained from computer simulations of large systems.

1995-01-01

378

Regulatory circuit for responses of nitrogen catabolic gene expression to the GLN3 and DAL80 proteins and nitrogen catabolite repression in Saccharomyces cerevisiae.  

UK PubMed Central (United Kingdom)

We demonstrate that expression of the UGA1, CAN1, GAP1, PUT1, PUT2, PUT4, and DAL4 genes is sensitive to nitrogen catabolite repression. The expression of all these genes, with the exception of UGA1...Full Text Available

1993-01-01

379

Pecularities of the superconducting gaps and the fermion-boson interaction in TmNi{sub 2}B{sub 2}C as seen by point-contact spectroscopy  

Energy Technology Data Exchange (ETDEWEB)

Point-contact (PC) investigations on the title compound in the normal and superconducting (SC) state (T{sub c}{approx_equal}10.6 K) are presented. The T-dependence of two SC gaps in TmNi{sub 2}B{sub 2}C determined by Andreev-reflection spectroscopy deviates from the BCS behavior in displaying a maximum at about T{sub c}/2. Additional evidence for the presence of a 2nd gap half as large as the main gap is given. For the first time ''reentrant'' features were found in the Andreev-reflection spectra measured in magnetic fields. The PC spectroscopy of the fermion-boson interaction in TmNi{sub 2}B{sub 2}C reveals a pronounced phonon maximum at 9.5 meV and a more smeared one around 15 meV, while at higher energies the PC spectra are almost featureless. Additionally, the intense peak slightly above 3 meV observed in the PC spectra of TmNi{sub 2}B{sub 2}C, is presumably caused by ...

2009-07-01

380

PBG structures for multi-beam devices  

International Nuclear Information System (INIS)

Photonic band gap structures with single or multiple defects show potential for use in single-beam and multi-beam klystrons and particle accelerators. The primary concerns are the coupling between the modes at each individual defect site and the damping of unwanted higher order modes. A conceptual design of a PBG based, multi-beam klystron and methods to damp HOMs and to cool and tune the structure are presented.

2002-12-12

381

International Symposium on Magnetic Suspension Technology. Part 2  

International Nuclear Information System (INIS)

In order to examine the state of technology of all areas of magnetic suspension and to review related recent developments in sensors and controls approaches, superconducting magnet technology, and design/implementation practices, a symposium was held. The proceedings are presented. The sessions covered the areas of bearings, sensors and controls, microgravity and vibration isolation, superconductivity, manufacturing applications, wind tunnel magnetic suspension systems, magnetically levitated trains (MAGLEV), space applications, and large gap magnetic suspension systems.

1991-08-19

382

Influence of microwaves on the order parameter relaxation time of superconducting aluminium  

Energy Technology Data Exchange (ETDEWEB)

Experimentally it is found that at constant temperature the order-parameter relaxation time, tausub(..delta..), decreases with increasing power of the microwaves, coupled into a superconducting strip. If the same increase in critical current, that corresponds with a given power of the microwaves, is obtained by lowering the temperature, the decrease in tausub(..delta..) is smaller. This reflects the fact that quasiparticles are removed more efficiently from the gap edge by microwaves than by lowering the temperature in equilibrium. A modified time-dependent Ginzburg-Landau equation is shown to describe these results adequately.

1982-04-01

383

Identifying the Key Weaknesses in Network Security at Colleges.  

Science.gov (United States)

A new study identifies and ranks the 10 security gaps responsible for most outsider attacks on college computer networks. The list is intended to help campus system administrators establish priorities as they work to increase security. One network security expert urges that institutions utilize multiple security layers. (DB)

1999-12-01

384

IDEAS: Regional Science and Urban Economics, Elsevier  

Wastenet

... (restricted)] 2009, Volume 39, Issue 5 523-529 Parents, peers, or school inputs: Which components of school outcomes are capitalized into house value? by Brasington, David M. & Haurin, Donald R. [Downloadable! (restricted)] 530-541 Trade liberalisation and agglomeration with firm heterogeneity: Forward and backward linkages by Okubo, Toshihiro [Downloadable! (restricted)] 542-552 Alternative measures of homeownership gaps across segregated ...

385

Disk's Spiral Arms Point to Possible Planets  

National Aeronautics and Space Administration (NASA)

Simulations of young stellar systems suggest that planets embedded in a circumstellar disk can produce many distinctive structures, including rings, gaps and spiral arms. This video compares computer simulations of hypothetical systems to an image of system SAO 206462 taken by the Subaru Telescope and its HiCIAO instrument. n nCredit: NASA Goddard Space Flight Center/NCSA

2011-10-18

386

Comparison of CT and MRI in patients with tibial plateau fracture: can CT findings predict ligament tear or meniscal injury?  

Energy Technology Data Exchange (ETDEWEB)

(1) To determine the accuracy of computed tomography (CT) in the evaluation of ligament tear and avulsion in patients with tibial plateau fracture. (2) To evaluate whether the presence or severity of fracture gap and articular depression can predict meniscal injury. A fellowship-trained musculoskeletal radiologist retrospectively reviewed knee CT and MRI examinations of 41 consecutive patients presenting to a level 1 trauma center with tibial plateau fractures. Fracture gap, articular depression, ligament tear and footprint avulsions were assessed on CT examinations. The MRI studies were examined for osseous and soft tissue injuries, including meniscal tear, meniscal displacement, ligament tear, and ligament avulsion. CT demonstrated torn ligaments with 80% sensitivity and 98% specificity. Only 2% of ligaments deemed intact on careful CT evaluation had partial or complete tears on MRI. Although the degree of fracture gap ...

2007-02-15

387

Characteristics of boiling transition of tight lattice rod assembly  

International Nuclear Information System (INIS)

Critical power characteristics of tight lattice rod assembly was investigated using a simple-shaped experimental apparatus. An electrically heated rod with four spacers was placed in a circular tube, and boiling transition condition for a rod in an annular geometry was clarified varing annulus clearance. It was found that critical heat flux depends strongly on the clearance accoding as the gap becomes smaller. This results was compared with KfK correlation and the trends were well correlated. (author).

388

Breakdown electroluminescence spectra in structures based on the solid solutions Ga/sub 1-x/Al/sub x/P(As)  

Energy Technology Data Exchange (ETDEWEB)

The authors investigate the breakdown luminescence spectra in reverse-biased p-n heterojunctions based on gallium and aluminum phosphides and arsenides for the purpose of determining their behavior as lasing and photodetection materials. Data are given on temperature coefficients, band gap structure, bremsstrahlung, hot carrier mobility and photon emission, and transition and recombination parameters.

1987-08-01

389

A single-stranded gap in human immunodeficiency virus unintegrated linear DNA defined by a central copy of the polypurine tract.  

UK PubMed Central (United Kingdom)

The structure of unintegrated human immunodeficiency virus type 1 (HIV-1) DNA from acutely infected human lymphoid cells was analyzed by nuclease S1 cleavage. We observed a unique, discrete single-stranded...Full Text Available

1991-05-01

390

Temperature-dependent properties of semiconductor quantum dots in coherent regime; Temperaturabhaengige Eigenschaften einzelner Halbleiter-Quantenpunkte im Kohaerenten Regime  

Energy Technology Data Exchange (ETDEWEB)

Recently, the public has become aware of keywords like ''Quantum computer'' or ''Quantum cryptography''. Regarding their potential application in solid state based quantum information processing and their overall benefit in fundamental research quantum dots have gained more and more public interest. In this context, quantum dots are often referred to as ''artificial atoms'', a term subsuming their physical properties quite nicely and emphasizing the huge potential for further investigations. The basic mechanism to be considered is the theoretical model of a two-level system. A quantum dot itself represents this kind of system quite nicely, provided that only the presence or absence of a single exciton in the ground state of that structure is regarded. This concept can also be expanded to the presence of two excitons (bi-exciton). Transitions between the relevant levels can be ...

2009-10-15

391

Criticality experiments: analysis, evaluation, and programs. 6. CORAL-I Reactor: Evaluation of Critical Experiments and Mass Reactivity Coefficient Measurement  

International Nuclear Information System (INIS)

CORAL-I was an experimental, zero-power, fast-spectrum, high-enriched metal uranium reactor that operated from 1968 until 1988 at the former Junta de Energia Nuclear (JEN), CIEMAT at present. The critical measurements performed at the startup of the reactor are being evaluated as part of the International Critical Safety Benchmark Evaluation Program (ICSBEP) and proposed to be included in its 2001 edition. Additionally, the measurement of the mass reactivity coefficient is compared with MCNP4B calculations. This measurement allows one to perform the approach to critical without the need of a previous control rod calibration, thus enhancing the safety of such an approach. This technique can also be applied to other reactor types. CORAL-I (Ref. 1) is a 90% enriched metal uranium reactor domestically designed and manufactured in the experimental facilities of JEN, now CIEMAT, in Madrid, Spain. The enriched uranium was supplied by the International Atomic Energy Agency as metal ingots and ...

2001-06-17

392

Turbulent heat transfer augmentation and friction in periodic fully developed channel flows  

Energy Technology Data Exchange (ETDEWEB)

Measurements are presented of the distribution of average friction factors (f) as well as local and average ({ovr Nu}) heat transfer coefficients for fully developed channel flows with two rib-roughened opposite walls. The temperature measurements were made by using both a laser holographic interferometer and thermocouples. In addition, the reattachment length was determined by flow visualization. The Reynolds number (Re) was varied from 5.0 {times} 10{sup 3} to 5.4 {times} 10{sup 4}; the rib pitch-to-height ratios (Pi/H) were 10, 15, 20; and the rib height-to-hydraulic diameter ratios (H/De) were 0.063, 0.081, and 0.106. The detailed results allowed the peaks of heat transfer augmentation and the regions susceptible to hot spots to be located and allowed the relative contribution of the rib surface and the channel wall to the heat transfer augmentation to be determined. Moreover, relative to a smooth duct, the enhancement of both {ovr Nu} and ...

1992-02-01

393

Root Architecture of Jarrah (Eucalyptus marginata) Trees in Relation to Post-Mining Deep Ripping in Western Australia  

British Library Electronic Table of Contents (United Kingdom)

Abstract This research aimed to investigate coarse root systems of Jarrah (Eucalyptus marginata Donn ex Sm.) trees at a 13-year-old restored bauxite mine site in south-western Australia. Excavations in an area with small trees (low-quality site) revealed that deep ripping equipment failed to penetrate the cemented lateritic subsoil, restricting coarse roots (roots >5 mm in diameter) to the top 0.5 m of the soil profile, resulting in fewer (1,344 stems/ha) and smaller (mean height 4.5 m) Jarrah trees. An adjacent area within the same pit (high-quality site), with a stand density of 3,256 stems/ha and a mean height of 8.0 m, had a kaolinitic clay subsoil which coarse roots penetrated to the average ripping depth (1.5 m). Trees at the low-quality site did not penetrate the subsoil with their ...

2007-01-01

394

Integral Field Unit Observations of NGC 4302: Kinematics of the Diffuse Ionized Gas Halo  

CERN Document Server

We present moderate resolution spectroscopy of extraplanar diffuse ionized gas (EDIG) emission in the edge-on spiral galaxy NGC 4302. The spectra were obtained with the SparsePak integral field unit (IFU) at the WIYN Observatory. The spectra are used to construct position-velocity (PV) diagrams at several ranges of heights above the midplane. Azimuthal velocities are directly extracted from the PV diagrams using the envelope tracing method, and indicate an extremely steep dropoff in rotational velocity with increasing height, with magnitude ~30 km/s/kpc. We find evidence for a radial variation in the velocity gradient on the receding side. We have also performed artificial observations of galaxy models in an attempt to match the PV diagrams. The results of a statistical analysis also favor a gradient of ~30 km/s/kpc. We compare these results with an entirely ballistic model of disk-halo flow, and find a strong dichotomy between the observed ...

2007-01-01

395

Fast Flux Test Facility reactor initial criticality predictions and measurements  

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) was designed to test fast-reactor fuels and other nonfuel materials. In its 37 reactor cycles of operations, the FFTF reactor has performed very well and successfully completed all the irradiation testings with an operating efficiency factor as high as 98%. Since FFTF is an experimental reactor, its core loading changed from cycle to cycle. Depending on the number of test assemblies in the core and their location, the core loading can change significantly from an essentially homogeneous core loading to a relatively nonhomogeneous or even highly localized heterogeneous loading. Consequently, the core reload design and initial criticality analyses were required for each operating cycle. The zero power initial critical control rod bank height was predicted before each reactor startup. The initial critical prediction depends on the reactivity conditions at the end of the previous cycle, the temperature feedback reactivities, the ...

1992-06-07

396

Evaluation of value for hydrogen release from high-level liquid waste. 4. Hydrogen release rate for {gamma}-ray radiolysis of simulated purex waste solutions  

Energy Technology Data Exchange (ETDEWEB)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of {sup 60}Co {gamma}-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H{sub 2}) = 0.100 d{sup -1.6}. The G-values of oxygen and nitrogen releases were also determined. (author)

1997-12-01

397

Evaluation of value for hydrogen release from high-level liquid waste. 4. Hydrogen release rate for #gamma#-ray radiolysis of simulated purex waste solutions  

International Nuclear Information System (INIS)

The rates of hydrogen release from simulated high-level liquid waste (SHLLW) during irradiation of "6"0Co #gamma#-rays have been studied using a laboratory-scale apparatus. The SHLLW used was made up of 28 different metal elements, the concentrations of which were determined from a computed data (ORIGEN-2) for a Purex spent fuel (burn-up of 4.5 GWd/t, cooling time of 4 years) except for those of corrosion products (Fe, Cr and Ni) and of chemical process additive (P). The nitrate ion concentration of the SHLLW was 4.97 M. The G-value of hydrogen release was 0.0164 for stirred conditions, but for nonstirred conditions with dose rate : 2.8 kGy/h and with the SHLLW solution height more than 8 cm, the following relation was found between the G-value and the solution height (d cm); G(H_2) = 0.100 d"-"1"."6. The G-values of oxygen and nitrogen releases were also determined. (author).

1997-01-01

398

Bar strengths in spiral galaxies estimated from 2MASS images  

CERN Document Server

Non-axisymmetric forces are presented for 107 spiral galaxies using the 2 Micron All Sky Survey (2MASS) images. We apply both Cartesian integration and a polar grid integration utilizing a limited number of azimuthal Fourier components of density. We found that bar strength is independent of the method used to evaluate the gravitational potential. However, the polar method is more suitable for weak and noisy images. Bar strength was found to be sensitive to the Hubble-type dependent scale height of the disk, which has been ignored in the previous studies. On the other hand, the method is rather insensitive to the vertical model of the disk, as long as a same vertical dispersion is assumed, or to the boxy/peanut shaped structure, studied in terms of non-constant vertical scale height along the disk. In the near-IR most galaxies in our sample show non-axisymmetric forces in some level, and 40 percent of them have bars in a sense that they have ...

2002-01-01

399

Voltage-current characteristics of point systems of metal-oxide-metal  

Science.gov (United States)

A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-

1975-10-01

400

Real time neutron transmission investigation of the austenite-bainite transformation in grey iron  

Energy Technology Data Exchange (ETDEWEB)

The first successful application of a new method to investigate phase transformations in real time, like the decomposition of austenite into bainite in grey iron, is described. During the ongoing transformation, transmission spectra of thermal neutrons, which contain Bragg edges corresponding to the crystal structure of the transforming phases, are recorded. By evaluating the height of these Bragg edges, which is a measure of the volume fraction of the phase, at different transformation times, the transformation can be followed in-situ in a time resolved manner. The method is compared to other previously used methods (micrographs, dilatometry, diffraction techniques); also a summary and an outlook are given. ((orig.))

1994-06-01

401

Real time neutron transmission investigation of the austenite-bainite transformation in grey iron  

International Nuclear Information System (INIS)

The first successful application of a new method to investigate phase transformations in real time, like the decomposition of austenite into bainite in grey iron, is described. During the ongoing transformation, transmission spectra of thermal neutrons, which contain Bragg edges corresponding to the crystal structure of the transforming phases, are recorded. By evaluating the height of these Bragg edges, which is a measure of the volume fraction of the phase, at different transformation times, the transformation can be followed in-situ in a time resolved manner. The method is compared to other previously used methods (micrographs, dilatometry, diffraction techniques); also a summary and an outlook are given. ((orig.)).

1994-01-01

402

Phase- and size-adjusted CT cut-off for differentiating neoplastic lesions from normal colon in contrast-enhanced CT colonography  

Energy Technology Data Exchange (ETDEWEB)

A computed tomography (CT) cut-off for differentiating neoplastic lesions (polyps/carcinoma) from normal colon in contrast-enhanced CT colonography (CTC) relating to the contrast phase and lesion size is determined. CT values of 64 colonic lesions (27 polyps <10 mm, 13 polyps {>=}10 mm, 24 carcinomas) were determined by region-of-interest (ROI) measurements in 38 patients who underwent contrast-enhanced CTC. In addition, the height (H) of the colonic lesions was measured in CT. CT values were also measured in the aorta (A), superior mesenteric vein (V) and colonic wall. The contrast phase was defined by xA + (1 - x)V using x as a weighting factor for describing the different contrast phases ranging from the pure arterial phase (x=1) over the intermediate phases (x=0.9-0.1) to the pure venous phase (x=0). The CT values of the lesions were correlated with their height (H), the different phases (xA + (1 - x)V) and the ratio [xA + (1 ...

2004-12-01

403

Peculiarities of large-scale yttrium ceramics samples fabrication with required grain size for units of a motor operating at liquid nitrogen temperature  

International Nuclear Information System (INIS)

Technologic regimes of cryomotor rotor fabrication are determined. Blanks of yttrium ceramics powder are molded hydrostatically at 400-600 MPa. To confirm the serviceability of electric machines of the considered, a hysteretic 10 W power electric motor with the following dimensions of HTSC-ceramics rotor: external diameter - 56 mm; internal diameter - 45 mm, height - 60 mm, is developed and tested in the liquid nitrogen medium. 8 refs.; 8 figs.; 1 tab.

1995-01-01

404

Neutron monitoring on cold fusion experiments  

International Nuclear Information System (INIS)

A helium-3 proportional detector was equipped with the experiment of Liaw-type electrolytic cell contained eutectic LiCl-KCl molten salt saturated by LiD electrolytic to collect the informations of the rate and the energy distribution of possible neutron produced during the electrolysis processes. For long time monitoring, the significant reproducible neutron bursts appeared at several runs of cells during electrolytic processing. The neutron counting rate increased about a factor of two above the level of the background measurement. The pulse height signals were verified of neutron energy ranging from thermal up to 350 keV. (author).

1992-10-01

405

Mixed convection flow in a horizontal rectangular channel subjected to a horizontal thermal gradient  

British Library Electronic Table of Contents (United Kingdom)

This paper deals with a mixed convection water flow in a horizontal rectangular duct, uniformly heated from one lateral vertical wall and thermally insulated elsewhere. The supplied heat flux induces a secondary flow, which structure is constituted of one longitudinal roll in the considered aspect ratio (??=?1.9), embedded into a return flow of possibly large stream wise extension (up to twenty channel heights). Such situation induces helicoidal trajectories for the fluid flow particles, which contributes to a heat transfer enhancement compared to purely forced convection flow.

2011-01-01

406

Mixed convection flow in a horizontal rectangular channel subjected to a horizontal thermal gradient  

Science.gov (United States)

This paper deals with a mixed convection water flow in a horizontal rectangular duct, uniformly heated from one lateral vertical wall and thermally insulated elsewhere. The supplied heat flux induces a secondary flow, which structure is constituted of one longitudinal roll in the considered aspect ratio (? = 1.9), embedded into a return flow of possibly large stream wise extension (up to twenty channel heights). Such situation induces helicoidal trajectories for the fluid flow particles, which contributes to a heat transfer enhancement compared to purely forced convection flow.

2011-04-01

407

JOINT PROBABILITIES FOE ENVIRONMENTAL LOADS (OCE 90)  

Environmental Research Database

ObjectivesObjectives Not AvailableDescriptionThis proposal seeks to extend what is currently the most comprehensive offshore environmental data collection programme at a platform on the UKGS involving continuous collection of wave height and direction, wind speed and direction, current and wave particle kinematics. Data has been collected with this system since 1994 and the proposal is to extend this until 1999 thus providing an extensive set of storm data collected at 5Hz which will allow examination of the joint behaviour of wave, wind [continued...

1998-01-16

408

Enriched lithium collection from lithium plasma flow  

International Nuclear Information System (INIS)

In order to understand the physical processes concerned with the selective heating by ion cyclotron resonance and with the subsequent collection of heated particles, experiments were carried out with the extraction of lithium samples, enriched with "6Li isotopes. Probe and integral extractors allow to collect enriched Li at the end of the selective heating region. Surface density distribution on the collector and local isotopic content of lithium are measured, as a function of the screen height and the retarding potential. Dependence of the collected amount of lithium and of its isotopic content on the value of the magnetic field is also measured. 4 figs., 2 tabs., 5 refs.

409

Electron temperature diagnostics in the RFX reversed field pinch experiment  

Energy Technology Data Exchange (ETDEWEB)

The paper presents an integrated approach to the problem of electron temperature diagnostics of the plasma in a reversed field pinch. Three different methods, sampling different portions of the electron distribution function, are adopted, namely Thomson scattering, soft X-ray spectroscopy by pulse-height analysis and filtered soft X-ray intensity ratio. A careful analysis of the different sources of systematic errors is performed and a novel statistical approach is adopted to mutually validate the three independent measurements. A satisfactory agreement is obtained over a large range of experimental conditions, indicating that in the plasma core the energy distribution function is well represented by a maxwellian. (author)

2000-08-01

410

Drop freezing on a substrate  

Energy Technology Data Exchange (ETDEWEB)

The freezing of liquid in the form of a granule on a cooled substrate is considered. On the basis of a hypothesis regarding the form of the isotherms in the granule, an analytical solution of the Stefan problem is obtained for two limiting cases: when a/sub d/ >> a/sub s/ and a/sub d/ << a/sub s/, where a/sub s/ and a/sub d/ are the thermal conductivity of the substrate and drop, respectively. The results of calculating the crystallization times of the granules as a function of their dimensions (height and diameter) and the substrate temperature, and also the dynamics of temperature variation at the base of the granule in the course of crystallization, are in good agreement with the experimental data.

1988-07-01

411

Comparison of Atmospheric Dispersion Models Between PHWR and PWR  

International Nuclear Information System (INIS)

The radiation dose and the atmospheric dispersion for Pressurized Heavy Water Reactors (PHWR) are based on the CAN/CSA N288.2-M91 standards: for Pressurized Water Reactor (PWR) on the NRC Regulatory Guide 1.145. There are some differences between in the methodologies used in the standards, including the atmospheric dispersion model, the release height, the temperature lapse rate, the cutoff condition. This paper reports on a comparison of standards for atmospheric dispersion models of PHWRs and PWRs in order to determine which one is the more conservative. The comparison between PHWR and PWR for atmospheric dispersion factors and radiation doses confirms that there are no big differences

2010-10-01

412

Application of /sup 252/Cf-source driven noise analysis measurements for subcriticality of HFIR fuel elements  

Energy Technology Data Exchange (ETDEWEB)

The approach-to-critical measurements reported were for a plate-type fuel element where the height of the water moderator and side and top reflector were increased. Measurements were also performed with each of the two annuli of the fuel element to verify both the presence of boron in the fuel plates and the proper uranium loading prior to assembly of the two annuli for full submersion measurements. Measurements were also performed with detectors external to the reflector (> 15 cm of water on top, bottom, and side) for the assembled, submerged HFIR fuel element.

1983-01-01

413

Actuating mechanism of a mine combine  

Energy Technology Data Exchange (ETDEWEB)

An actuating mechanism of a mine combine is proposed. It includes a rotating platform in a vertical plane on which by hinges with the possibility of rotation parallel to the plane of the platform there are handles with cutting drums and a mechanism for extension of the handle which has hydraulic cylinders. With a decrease in load on the hinges of the handles from bending forces, on the platform between the front edge of the platform and the site of attachment of the handle hinges there are openings. Each handle has a support projection which is placed in this opening with the possibility of movement. A clamp plank is installed on it which covers the opening. The distance from the center of the projection support to the axis of the corresponding hinge is greater than the height of embedding of this hinge into the platform.

1982-01-01

414

U.S. Department Of Energy's nuclear engineering education research: highlights of recent and current research-II. 4. Studies of Forced-Convection Heat Transfer Augmentation in Large Containment Enclosures  

International Nuclear Information System (INIS)

This paper provides information on heat transfer enhancement due to jet mixing inside a cylindrical enclosure. The work addresses conservative heat transfer assumptions regarding mixing and condensation that have typically been incorporated into passive containment design analyses. The current research presents an interesting possibility for increasing decay heat removal of passive containment systems under combined natural and forced convection. Eliminating these conservative assumptions could provide the basis for a change of containment design and reduce the construction cost. It is found that the ratio of forced- and free convection Nusselt numbers can be predicted as a function of the Archimedes number and a correlated factor accounting for jet orientation and enclosure geometry. To use the small-scale tests for large containment design, scale-up methods and criteria are important for matching the key governing parameters and fluid properties. In the present experiment, a ...

2001-06-17

415

Conservative treatment of choroidal melanomas using iodine brachytherapy; Tratamento conservador ocular dos melanomas de coroide com braquiterapia utilizando placas de Iodo-125  

Energy Technology Data Exchange (ETDEWEB)

Objective: To retrospectively evaluate the results of conservative therapy using escorpal iodine-125 (model 6711, Amershan) plaque for brachytherapy of choroidal melanoma. Materials And Methods: We evaluated 49 patients with choroidal melanoma treated at 'Hospital do Cancer', Sao Paulo, Brazil, from March 2001 to January 2003. The following clinical parameters were analyzed and correlated with local control and survival rate: gender, age, lesion dimension, treatment duration, as well as doses in apex and base of the tumors. Results: The maximum diameter and height of the base of the tumors treated were 17 mm and 12 mm, respectively. Doses at those points ranged from 213 to 463 Gy (median: 347 Gy) and 51 to 250 Gy (median: 91 Gy), respectively. The actuarial rates of ocular preservation, disease free survival and ocular preservation in 2-years were 96%, 93.5% and 96.3%, respectively. A tumor height < 6 mm was the only ...

2004-08-01

416

A study of palladium silicide formed by focused ion beam implantation of palladium ions  

Science.gov (United States)

The formation and properties of Pd{sub 2}Si formed by focused ion beam implantation of Pd ions into Si is presented in this thesis. An extensive microstructural study using transmission electron microscopy was undertaken and the as-implanted as well as annealed microstructure is shown. Results of other analysis techniques such as Rutherford back scattering and secondary ion mass spectrometry etc. are also presented. Kinetic information on the growth of Pd{sub 2}Si obtained by both microstructural and resistance measurements indicates that the activation energy for growth of the silicide is around 0.36 to 0.39 eV. This can be compared with the normally reported value of 1.5 eV for Pd{sub 2}Si formed by annealing thin film Pd on Si. The growth of the silicide was found to follow t{sup 1/2} kinetics. Microstructural observation of the as-implanted samples showed extensive in-situ formation of Pd{sub 2}Di and also surprisingly few defect structures. A heat transfer model for the ...

1989-01-01

417

A study of palladium silicide formed by focused ion beam implantation of palladium ions  

International Nuclear Information System (INIS)

The formation and properties of Pd_2Si formed by focused ion beam implantation of Pd ions into Si is presented in this thesis. An extensive microstructural study using transmission electron microscopy was undertaken and the as-implanted as well as annealed microstructure is shown. Results of other analysis techniques such as Rutherford back scattering and secondary ion mass spectrometry etc. are also presented. Kinetic information on the growth of Pd_2Si obtained by both microstructural and resistance measurements indicates that the activation energy for growth of the silicide is around 0.36 to 0.39 eV. This can be compared with the normally reported value of 1.5 eV for Pd_2Si formed by annealing thin film Pd on Si. The growth of the silicide was found to follow t"1"/"2 kinetics. Microstructural observation of the as-implanted samples showed extensive in-situ formation of Pd_2Di and also surprisingly few defect structures. A heat transfer model for the implantation indicates no ...

418

Synthesis, characterization and optical properties of a high NIR reflecting yellow inorganic pigment: Mo"6"+ doped Y_2Ce_2O_7 as a cool colorant  

International Nuclear Information System (INIS)

Full text: Pigments possessing the ability to confer high solar reflectance have received considerable attention in recent years. The inorganic class of NIR reflective pigments are mainly metal oxides and are primarily employed in two applications: (i) visual camouflage and (ii) reducing heat build up. More than half of the solar radiation consists of near-infrared radiation (52%), the remaining being 43% visible light and 5% ultraviolet radiation. Over heating due to solar radiation negatively affects comfort in the built environment and contributes substantially to electrical consumption for air conditioning and release of green house gases. A pigment which has strong reflections in the NIR region (780-2500 nm) can be referred to as a 'cool' pigment. However, most of the NIR reflective inorganic pigments particularly yellow (eg. cadmium yellow, lead chromate, chrome titanate yellow etc.) contain toxic metals and hence their consumption is being limited. Replacing them with ...

2010-11-24

419

Fundamental Chemistry And Thermodynamics Of Hydrothermal Oxidation Processes  

Science.gov (United States)

Hydrothermal oxidation (HTO) is a promising technology for the treatment of aqueous-fluid hazardous and mixed waste streams. Waste streams identified as likely candidates for treatment by this technology are primarily aqueous fluids containing hazardous organic compounds, and often containing inorganic compounds including radioisotopes (mixed wastes). These wastes are difficult and expensive to treat by conventional technologies (e.g. incineration) due to their high water content; in addition, incineration can lead to concerns related to stack releases. An especially attractive potential advantage of HTO over conventional treatment methods is the total containment of all reaction products within the overall system. The potential application of hydrothermal oxidation (HTO) technology for the treatment of DOE hazardous or mixed wastes has been uncertain due to concerns about safe and efficient operation of the technology. In principle, aqueous DOE wastes, including hazardous an d mixed ...

2001-12-31

420

Preparation of nanostructure Ni doped CdO thin films by sol gel spin coating method  

British Library Electronic Table of Contents (United Kingdom)

The nanostructure Ni-doped CdO films have been prepared by sol gel spin coating method. Atomic force microscopy results indicate that the CdO films are formed from the nanoparticles and the grain size is changed with nickel content. X-ray diffraction patterns of the films indicate that the undoped and Ni-doped CdO films have polycrystalline structure with a cubic sodium chloride structure, showing two main characteristic peaks assigned to the (111) and (200) planes. The optical band gap values of undoped and Ni-doped CdO films were determined by optical absorption method. The Eg values of the CdO films were found to be in the range of 2.26?2.60?eV. The Eg values of the CdO films increase with the content of Ni dopant (up to 6% Ni). It is evaluated that the optical band gap and grain size o...

2011-01-01

421

Latest technologies for process control in hot rolling mill; Netsukanatsuen miru ni okeru saishin no purosesu seigyo gijutsu  

Energy Technology Data Exchange (ETDEWEB)

The most recently developed control technologies in a hot strip mill are described. Preview AGC has been developed with a preview control synthesis. It controls roll gaps by using the previous information of disturbances. The disturbances which are concerned are derived from the rolling force, the roll gap and the thickness of a previous stand. The thickness accuracy and the availability of mill have been improved by this technology. An on-line roll grinding (ORG) system with an on-line roll profile meter (OPM) has been developed for the purpose of achieving schedule-free rolling. The ORG smooths the worn and roughed surface of a work roll and OPM can measure the profile of a revolving roll without contact. The data obtained by the OPM are given as feedback information to the ORG. As a result, grinding accuracy has been improved and rolling restriction on width has been relaxed widely. (author)

1999-12-01

422

Interface-induced conversion of infrared to visible light at semiconductor interfaces  

Science.gov (United States)

Efficient, low-temperature conversion of infrared light into visible light (red, orange, green) is reported at single heterojunctions and undoped quantum wells of GaAs and ordered Al{sub {ital x}}Ga{sub 1{minus}{ital x}}InP{sub 2}; an increase in photon energy of 700 meV is obtained. The signal originates from the high-band-gap layers and disappears only if the excitation energy is tuned below the GaAs band gap. The intensity of the up-converted photoluminescence (PL) is found to decrease significantly slower with increasing temperature than that of the regular PL and it remains observable up to 200 K. Interface-induced cold Auger processes along with the presence of trapped states for both electrons and holes in these ordered alloys account for this nonlinear mechanism. A colinear double-beam experiment confirms this. {copyright} {ital 1996 The American Physical Society.}

1996-08-01

423

Integrating Research, Policy, and Practice to Bring Science to the Classroom: New Leaders' Perspectives on the Field of Emotional and Behavioral Disorders  

Science.gov (United States)

In 1991, the Peacock Hill Working Group provided the field of emotional and behavioral disorders (EBD) a roadmap for improving the quality of services provided to students with EBD. The working group considered issues at every level of the educational system, from the classroom to federal policy. Although many strides have been made in the past 20 years regarding the education and treatment of students with EBD, the gap has persisted between empirically validated practices and the classroom routines of teachers serving students from this population. In the authors' view, the field of EBD would benefit greatly from conceptual and empirical developments to improve the mechanisms required to bring science to the classroom. Using the theoretical underpinnings of implementation science, the authors describe a transactional model for integrating research, policy, and practice to close the research-to-practice gap. Recommendations for researchers, ...

2010-08-01

424

Energy band structure of LaCuOCh (Ch = S, Se and Te) calculated by the full-potential linearized augmented plane-wave method  

International Nuclear Information System (INIS)

Energy band diagrams of LaCuOCh (Ch = S, Se and Te) were calculated by a full-potential linearized augmented plane-wave method. The calculations, based on the local density approximation with/without an on-site Coulomb repulsion parameter, were to examine the energy levels of La 4f states. The results of the calculations showed that the on-site correlation parameter is necessary for evaluating the energy levels of La 4f states appropriately. The calculations for LaCuOCh with the on-site correlation parameter revealed that LaCuOS and LaCuOSe have almost the same energy band structure with a direct allowed-type band gap, while LaCuOTe has significantly different conduction band structure that exhibits an indirect-type band gap. This difference in electronic structure between LaCuOCh (Ch = S, Se and Te) is consistent with the observed optical properties of these materials.

2004-07-21

425

Analytical study of thermal response similarity between simulated fuel rods and nuclear fuel rods during reflood phase of PWR-LOCA  

International Nuclear Information System (INIS)

The applicability of the thermal response of an electrically heated simulated rod mostly used in loss-of-coolant-accident (LOCA) experiments to that of a nuclear fuel rod is a concern for the safety evaluation of a reactor. The present analysis describes the characteristics of the thermal response for both electrically heated and nuclear fuel rods during typical reflood conditions for a PWR-LOCA. A model describing the radial temperature field in the rod is developed based on the scheme in HETRAP code by Malang and incorporated into a reflood analysis code, REFLA for that purpose. The calculations applied to the existing reflood tests gave good agreement with experiments, showing the validity of the present model. The analysis has shown that the nuclear fuel rod tends to give a lower clad temperature and a sooner quench time than the electrically heated rod in a typical reflood condition, due to the smaller gap heat transfer and smaller heat capacity of the ...

426

The crack of harden cement paste observed with multi-technique  

British Library Electronic Table of Contents (United Kingdom)

The shrinkage of the cement paste with low water-cement ratio at different relative humidity was observed and analyzed with ESEM and deformation map technique. The crack morphology was observed with different magnification with SEM and FESEM, and the formation of the crack was observed with AFM between two C-S-H nano particles. The observation by multi technique at multi scale indicated that the shrinkage was increase with the decrease of the humidity due to the increase of the pressure of the capillary pressure, the morphology of the crack in smaller scale was similar to that in the bigger scale, the smaller crack distributed in the latticework of the bigger ones, and the crack propagated along the gap between two nano particles of C-S-H with weaker bonding.

2010-01-01

427

The behavior of bonded doubler splices for composite sandwich panels  

Science.gov (United States)

The results of an investigation into the behavior of adhesively bonded doubler splices of two composite material sandwich panels are presented. The splices are studied from three approaches: analytical; numerical (finite elements); and experimental. Several parameters that characterize the splice are developed to determine their influence upon joint strength. These parameters are: doubler overlap length; core stiffness; laminate bending stiffness; the size of the gap between the spliced sandwich panels; and room and elevated temperatures. Similarities and contrasts between these splices and the physically similar single and double lap joints are discussed. The results of this investigation suggest several possible approaches to improving the strength of the sandwich splices.

1980-07-01

428

Technology development tendency and R and D idea of NPP radiation monitoring system  

International Nuclear Information System (INIS)

This paper gives a general description of functions, usages and system configurations of the instruments and their major units or components of the radiation monitoring system, as well as the status and technical gap between domestic and foreign technologies. And then the paper also puts forward an idea on product R and D, i.e. combination of independent R and D and innovation, assimilation and re-innovation of foreign advanced technology at present situation in order to keep pace with the rapid development of nuclear power in China and achieve the goal of localization of nuclear power equipment. (authors)

2009-06-01

429

Target identification of buried coated objects  

Scientific Electronic Library Online (English)

Abstract in english We consider the three dimensional electromagnetic inverse scattering problem of determining information about a buried coated object from a knowledge of the electric and magnetic fields measured on the surface of the earth corresponding to time harmonic electric dipoles as incident fields. We assume that the buried object is a perfect conductor that is (possibly) partially coated by a thin dielectric layer. No a priori assumption is made on the extent of the coating, i.e. (more) the object can be fully coated, partially coated or not coated at all. We present an algorithm based on the linear sampling method and reciprocity gap functional for reconstructing the shape of the scattering obstacle together with an estimate of the surface impedance of the coating.

2006-01-01

430

Sub-wavelength localization of near-fields in coupled metallic spheres for single emitter polarization analysis  

CERN Document Server

We numerically demonstrate selective near-field localization determined by the polarization state of a single emitter coupled to plasmonic nano-cluster. Seven gold nanospheres are carefully arranged such that up to ten polarization states of the single emitter, including linear, circular, and elliptical polarizations, can be distinguished via the distinct field localization in four gaps. The ability to transform polarization state into field spatial localization may find application for single emitter polarization analysis.

2011-01-01

431

Static potential of open bosonic membranes  

Energy Technology Data Exchange (ETDEWEB)

We study the static potential of open bosonic membranes in the 1/d approximation, where d is the space-time dimensionality. For a fixed square boundary of side length R we find, in contrast to the string potential, no critical distance below which tachyons appear. Instead, we find a correction factor to the classical potential, V/sub cl/=kR/sup 2/, which for small distances shifts the perturbative ground state energy by a positive constant. We interpret the shift as the mass gap of this quantum membrane.

1989-03-30

432

Spontaneous radiation and lamb shift in three-dimensional photonic crystals  

Science.gov (United States)

Spontaneous emission in photonic crystals with anisotropic three-dimensional dispersion relation is studied. If the upper level is below a characteristic frequency omega(1), or above omega(2), or between omega(1) and omega(2), the radiation is a localized field with a frequency in the band gap, or a propagating field with a frquency in the band, or a diffusion field, respectively. An analytical expression for the Lamb shift is obtained. The Lamb shift for the current case is small compared to that in an ordinary vacuum or in one- or two-dimensional photonic crystals due to lower density of states. PMID:11017227

2000-03-01

433

Regenerative zinc/air and zinc/ferricyanide batteries for stationary power applications  

Energy Technology Data Exchange (ETDEWEB)

The authors report a novel configuration for a zinc-particle, packed-bed anode in which an open structure of high hydraulic permeability is maintained indefinitely in a cell with closely spaced walls by the formation of particle bridges and associated gaps. The configuration minimizes electrolyte pumping costs, allows rapid refueling and partial recharge, and provides for 100% zinc consumption. This approach benefits zinc/air fuel batteries by allowing nearly continuous operation and fuel recycle without commercial infrastructure; it benefits Zn/[Fe(CN){sub 6}]{sup {minus}3} batteries by eliminating shape-change and polarization problems found with planar anodes.

1994-05-01

434

Read/write characteristics of focused-ion-beam-etched heads for perpendicular magnetic recording media  

International Nuclear Information System (INIS)

The read/write characteristics for perpendicular magnetic recording media of focused-ion-beam (FIB)-etched recording heads were investigated. It was found that the trailing edge of an FIB-etched head produces a higher gradient in the magnetic field perpendicular to the medium than a head which has not been etched. The signal-to-noise ratio of the medium increased with the FIB-etched write gap. A high-Bs and thin pole increased the magnetic field's gradient in the perpendicular direction, resulting in excellent read/write characteristics.

2001-10-01

435

Potential vulnerabilities of nuclear fuel cycle facilities to the year 2000 (Y2K) issue and measures to address them  

International Nuclear Information System (INIS)

The exchange of information and experience among Member Sates is an essential component of the IAEA action plan for addressing the Year 2000 problem. The objective is to enable Member States to identify any gaps in their own conversion programmes, benefit form the experience of others in developing remedial actions and establish the basis for future action to solve remaining problems. Experts in Year 2000 issues particularly those related to digital equipment prepared this report dealing with nuclear fuel cycle facilities

1993-04-18

436

Mode theory of the plasma cladding waveguide  

International Nuclear Information System (INIS)

The plasma cladding waveguide, which is a cylindrical dielectric core surrounded by a plasma cladding, is developed, and the guided modes and their characteristics of this waveguide are displayed through the present detailed theoretical research. The conditions of the single mode existing in the plasma cladding waveguide have been given, and the defined forbidden gap of frequency is discussed. It is found that the usage characteristics of the plasma cladding waveguide vary strongly with plasma frequency, and changing the plasma parameters can control the propagation mode. This paper focuses on exhibiting the basic characteristics and the potential applications of this new type of waveguide.

2007-04-07

437

Measurement of AlP/GaP (001) heterojunction band offsets by x-ray photoemission spectroscopy  

Energy Technology Data Exchange (ETDEWEB)

X-ray photoemission spectroscopy has been used to measure the valence band offset {Delta}E{sub v} for the AlP/GaP (001) heterojunction interface. The heterojunction samples were prepared by molecular-beam epitaxy. A value of {triangle}E{sub v}=0.43 eV is obtained (staggered band alignment, with AlP valence band below that of GaP). 24 refs., 8 figs., 1 tab.

1993-07-01

438

Magnetic and transport properties of Pr_2Pd_3Si_5  

International Nuclear Information System (INIS)

The results obtained from the magnetization, specific heat and electrical resistivity measurements on a polycrystalline sample of Pr_2Pd_3Si_5 are reported. The temperature dependence of magnetic susceptibility at low field (0.01 T) exhibits pronounced anomaly below 7 K due to antiferromagnetic ordering. The electrical resistivity and specific heat data also exhibit sharp transition at 6.6 K evidencing the onset of antiferromagnetic order. A fit to the electrical resistivity data below 6 K suggests the presence of an energy gap in magnon spectrum in the ordered state. (author)

2008-12-16

439

Local Heine-Abarenkov model potential for III-V and II-VI covalent compounds  

Energy Technology Data Exchange (ETDEWEB)

A local Heine-Abarenkov model potential is proposed for zinc blende-type crystals. The potential parameters are determined by satisfying the zero pressure condition and the first zero of the empirical pseudopotential interpolated from band calculations. Two sets of parameters are presented for thirteen tetrahedral compounds such as AlP, AlAs, AlSb, GaP, GaAs, GaSb, InP, InAs, InSb, ZnS, ZnSe, ZnTe, and CdTe.

1983-10-01

440

Loaded Transducer Fpr Downhole Drilling Component  

Energy Technology Data Exchange (ETDEWEB)

A robust transmission element for transmitting information between downhole tools, such as sections of drill pipe, in the presence of hostile environmental conditions, such as heat, dirt, rocks, mud, fluids, lubricants, and the like. The transmission element maintains reliable connectivity between transmission elements, thereby providing an uninterrupted flow of information between drill string components. A transmission element is mounted within a recess proximate a mating surface of a downhole drilling component, such as a section of drill pipe. To close gaps present between transmission elements, transmission elements may be biased with a "spring force," urging them closer together.

2005-07-05

441

Lateral optical confinement of the heterostructure semiconductor Raman laser  

Science.gov (United States)

This letter describes the first lasing experiment of the heterostructure semiconductor Raman laser with lateral confinement of both the Stokes and pump fields. It has a GaP Raman active layer with thickness of 10 ..mu..m and Al/sub 0.1/Ga/sub 0.9/P cladding layers. The stripe of the active layer has been fabricated by a plasma etching technique. Steps should be taken to realize the semiconductor Raman laser pumped by an injection laser, applicable to wideband optical communication.

1987-11-02

442

Idaho National Laboratory 2013-2022 Ten-Year Site Plan  

Energy Technology Data Exchange (ETDEWEB)

The Idaho National Laboratory (INL) Ten-Year Site Plan (TYSP) describes the strategy for accomplishing the long-term objective of transforming the laboratory to meet Department of Energy (DOE) national nuclear research and development (R&D) goals, as outlined in DOE strategic plans. The plan links R&D mission goals and INL core capabilities with infrastructure requirements (single- and multi-program), establishs the 10-year end-state vision for INL complexes, and identifies and prioritizes infrastructure needs and capability gaps. The TYSP serves as the basis for documenting and justifying infrastructure investments proposed as part of the FY 2013 budget formulation process.

2011-06-01

443

Full potential linearized augmented plane wave calculations of structural and electronic properties of GeC, SnC and GeSn  

International Nuclear Information System (INIS)

A theoretical study of structural and electronic properties of GeC, SnC and GeSn is presented using the full potential linearized augmented plane wave method. In this approach, the generalized gradient approximation was used for the exchange-correlation potential. Results are given for lattice constant, bulk modulus and its pressure derivative in both zinc-blende and rocksalt structures. Band structure, density of states and band gap pressure coefficients in zinc-blende structure are also given. The results are compared with previous calculations and with experimental measurements.

2003-08-01

444

Forward contracts in electricity markets: The Australian experience  

International Nuclear Information System (INIS)

Forward contracts play a vital role in all electricity markets, and yet the details of the market for forward contracts are often opaque. In this paper we review the existing literature on forward contracts and explore the contracting process as it operates in Australia. The paper is based on interviews with participants in Australia's National Electricity Market (NEM). The interviews were designed to understand the contracting process and the practice of risk management in the Australian energy-only pool market. This survey reveals some significant gaps between the assumptions made in the academic literature and actual practice in the Australian market place. (author)

2007-05-01

445

Electronic structure and properties of boron phosphide and boron arsenide  

International Nuclear Information System (INIS)

The composite wave variational version of the APW (augmented plane wave) method is used to obtain the electronic band structure of the compounds boron phosphide and boron arsenide at the high symmetry points #GAMMA#, X, and L. The tight binding interpolation scheme of Slater and Koster is used to calculate the rest of the band structure. The results show that both these materials are indirect band gap semiconductors. The density of states, and the imaginary part of the dielectric constant is also calculated. The theoretical results are compared with the reported experimental and theoretical data. (author).

446

Electron self-energy of high temperature superconductors as revealed by angle-resolved photoemission.  

Energy Technology Data Exchange (ETDEWEB)

In this paper, we review some of the work our group has done in the past few years to obtain the electron self-energy of high temperature superconductors by analysis of angle-resolved photoemission data. We focus on three examples which have revealed: (1) a d-wave superconducting gap, (2) a collective mode in the superconducting state, and (3) pairing correlations in the pseudogap phase. In each case, although a novel result is obtained which captures the essence of the data, the conventional physics used leads to an incomplete picture. This indicates that new physics needs to be developed to obtain a proper understanding of these materials.

1997-12-05

447

Duality picture between antiferromagnetism and d-wave superconductivity in t-J model at two dimensions  

Energy Technology Data Exchange (ETDEWEB)

The author shows in this paper an interesting relation between elementary and topological excitations in the antiferromagnetic and d-wave superconducting phases of the t-J model at two dimensions. The topological spin and charge excitations in one phase have the same dynamics as elementary excitations in the other phase, except the appearance of energy gaps. Moreover, the transition from one phase to another can be described as a quantum disordering transition associated with the topological excitations. Based on the above picture, a plausible phase diagram of t-J model is constructed.

2000-02-10

448

Downstream natural gas in Europe-High hopes dashed for upstream oil and gas companies  

International Nuclear Information System (INIS)

Access for independents to retail gas markets was a central concern in European policy reform efforts in the 1990s. Upstream oil and gas companies reacted with strategic intentions of forward integration. By late 2004, forward integration was still weak, however. An important explanation of the gap between announced strategic re-orientation and actual strategy implementation lies in the political failure of EU member states to dismantle market barriers to entry for independents. Variations between companies in downstream strategy implementation are explained by variations in business opportunities and internal company factors.

2007-01-01

449

Design of a 2 T multipole wiggler insertion device for the SRS  

International Nuclear Information System (INIS)

Two new identical insertion devices have been designed for the Daresbury SRS. They are 2T permanent-magnet multipole wigglers that will provide high flux in the X-ray region. This paper describes the magnetic and mechanical design of the arrays of steel pole pieces and permanent-magnet blocks. Also given is the engineering design of the support structure that will cope with the very large forces present while maintaining high levels of precision in gap setting and parallelism. The engineering design has been fully assessed using finite-element techniques to predict the deflections of critical parts of the structure. These two devices are due to be installed into the SRS by the end of 1998.

1998-05-01

450

CRC handbook of nuclear reactors calculations. Vol. III  

International Nuclear Information System (INIS)

This handbook breaks down the complex field of nuclear reactor calculations into major steps. Each step presents a detailed analysis of the problems to be solved, the parameters involved, and the elaborate computer programs developed to perform the calculations. This book bridges the gap between nuclear reactor theory and the implementation of that theory, including the problems to be encountered and the level of confidence that should be given to the methods described. Volume III: Control Rods and Burnable Absorber Calculations. Perturbation Theory for Nuclear Reactor Analysis. Thermal Reactors Calculations. Fast Reactor Calculations. Seed-Blanket Reactors. Index.

451

CRC handbook of nuclear reactors calculations. Vol. II  

International Nuclear Information System (INIS)

This handbook breaks down the complex field of nuclear reactor calculations into major steps. Each step presents a detailed analysis of the problems to be solved, the parameters involved, and the elaborate computer programs developed to perform the calculations. This book bridges the gap between nuclear reactor theory and the implementation of that theory, including the problems to be encountered and the level of confidence that should be given to the methods described. Volume II: Monte Carlo Calculations for Nuclear Reactors. In-Core Management of Four Reactor Types. In-Core Management in CANDU-PHW Reactors. Reactor Dynamics. The Theory of Neutron Leakage in Reactor Lattices. Index.

452

An analysis of a firm?s capacity in Mazda?s Keiretsu  

British Library Electronic Table of Contents (United Kingdom)

Capacity is defined as the power resulting from the specific position of a company in a network organization. This article extends the theory of network organizations to examine Mazda?s Yokokai Keiretsu, and proposes a new approach to calculating a firm?s capacity in a network. Capacity is divided into two categories, take-in capacity and take-out capacity, and the gap between them is called the capacity difference. We analyze the impact of capacity difference as a determinant of corporate performance in network organizations, thus providing a new perspective for successful corporate management.

2011-01-01

453

A study on the relation between linguistics-oriented and domain-specific semantics  

CERN Document Server

In this paper we dealt with the comparison and linking between lexical resources with domain knowledge provided by ontologies. It is one of the issues for the combination of the Semantic Web Ontologies and Text Mining. We investigated the relations between the linguistics oriented and domain-specific semantics, by associating the GO biological process concepts to the FrameNet semantic frames. The result shows the gaps between the linguistics-oriented and domain-specific semantics on the classification of events and the grouping of target words. The result provides valuable information for the improvement of domain ontologies supporting for text mining systems. And also, it will result in benefits to language understanding technology.

2010-01-01

454

A T-2 translational research perspective on interventions to improve post-fracture osteoporosis care  

British Library Electronic Table of Contents (United Kingdom)

The objectives of this paper are to: quickly outline the extent of the care gap in osteoporosis; define T-2 (knowledge) translation and its relationship to quality improvement; discuss the barriers to best practice in osteoporosis care after a fracture; convey the importance of rigor in design and evaluation of translational interventions by drawing upon examples from the broader literature; describe in some detail a series of post-fracture intervention trials conducted in Alberta, Canada; and make some conclusions specifically about osteoporosis interventions and more generally about T-2 translational research.

2011-01-01

455

Void fraction and phase distribution of a rotating two-phase gas-liquid flow around a plasma arc under water  

Energy Technology Data Exchange (ETDEWEB)

Plasma arc welding processes are used in off-shore industry for construction and maintenance in the wet surrounding of underwater structures and pipelines. In greater water depth the density of the plasma gas increase because of the greater hydrostatic pressure. This causes the increase of conductive heat losses to the wet surrounding. To keep up the energy flux to the workpiece to be welded, the plasma arc has to burn in a local dry area with an inside pressure of 1 bar. This requirement can be fulfilled by a rotating cylinder with a liquid film flowing down the inner wall. The flow around the rotating cylinder to create a local dry area around the plasma arc under water is experimentally investigated. The rotating cylinder is placed above the work surface which is simulated by a flat plate. According to the centrifugal forces of the rotating flow inside the gap between the lower end of the cylinder and the flat plate the water is forced out of the cylinder. The ...

1994-12-31

456

Thermal wet oxidation of GaP and Al{sub 0.4}Ga{sub 0.6}P  

Science.gov (United States)

Thermal wet oxidations of GaP and Al{sub 0.4}Ga{sub 0.6}P at 650 degree sign C for various times have been performed. Comparisons are made on oxidation rates and post oxidation morphology. Transmission electron microscopy shows that when oxidizing GaP, polycrystalline monoclinic GaPO{sub 4}{center_dot}2H{sub 2}O forms without noticeable loss of phosphorus. Oxidation for 6 h or more leads to poor morphology resulting in cracks and detachment. A thickness expansion of about 2.5-3 times is noticed as a result of oxidation. In contrast, oxidized Al{sub 0.4}Ga{sub 0.6}P exhibits much better morphology without cracks or detachment from the substrate. The oxide has an almost amorphous-like microstructure. The oxidation process shows typical diffusion-limited reaction at long anneals. Preliminary work on the oxidation of AlP indicates that the reaction leads to formation of Al{sub 2}O{sub 3} and possible volatile P{sub 2}O{sub 5} diffusing out of the ...

2000-08-21

457

Sodium fast reactor gaps analysis of computer codes and models for accident analysis and reactor safety.  

Science.gov (United States)

This report summarizes the results of an expert-opinion elicitation activity designed to qualitatively assess the status and capabilities of currently available computer codes and models for accident analysis and reactor safety calculations of advanced sodium fast reactors, and identify important gaps. The twelve-member panel consisted of representatives from five U.S. National Laboratories (SNL, ANL, INL, ORNL, and BNL), the University of Wisconsin, the KAERI, the JAEA, and the CEA. The major portion of this elicitation activity occurred during a two-day meeting held on Aug. 10-11, 2010 at Argonne National Laboratory. There were two primary objectives of this work: (1) Identify computer codes currently available for SFR accident analysis and reactor safety calculations; and (2) Assess the status and capability of current US computer codes to adequately model the required accident scenarios and associated phenomena, and identify important gaps. ...

2011-06-01

458

Electronic and structural properties of #beta#-Be_3N_2  

International Nuclear Information System (INIS)

We report the results of a theoretical study of the electronic and structural properties of the hexagonal beryllium nitride, using first principle pseudopotential plane wave (PP-PW) as well as full potential linearized augmented plane wave (FP-LAPW) methods within density functional theory. In the case of PP-PW we generated the pseudopotential by the highly optimized Q_c-tuning method and used the local density approximation and generalized gradient approximation (GGA) for the exchange-correlation potential. We applied pressure on the unit cell by the Wentzcovitch and traditional methods. In the FP-LAPW approach only the GGA was used for the exchange-correlation potential. Our calculated values for structural properties, based on both approaches are in reasonable agreement with experimental and other theoretical (Hartree Fock) results. By applying the above two approaches and also the Tight Binding Linear Muffin Thin Orbital method, the ground state Kohn-Sham eigenvalues were ...

459

Ab initio calculations of the electronic structure of the silver palladium oxide Ag_2PdO_2  

International Nuclear Information System (INIS)

Ab initio calculations of the electronic structure were performed for the silver palladium oxide, Ag_2PdO_2, by the full potential mixed linearized augmented plane wave and augmented plane wave plus local orbitals method (mixed LAPW/APW+lo) within the density functional theory and using the generalized gradient approximation (GGA96, Phys. Rev. Lett. 77 (1996) 3865) for the exchange-correlation potential. The lattice parameters were calculated from the ground-state total energy versus volume curve, and are in good agreement with the available experimental results. Our calculations of band structure predicted that the compound Ag_2PdO_2 has indirect band gap, and the Pd 4d states strongly hybridize with the O 2p states all over the valence bands and conduction bands. The valence bands are composed mainly of Ag, Pd 4d states and O 2p states, while the conduction bands consist mainly of the Pd 4d states and O 2p states. In addition, focusing on the calculation ...

2003-09-01

460

Toward finding an optimal stockpile geometry to reduce dust emissions  

Energy Technology Data Exchange (ETDEWEB)

Fugitive dust emissions from stockpiles in the open storage yards of industrial zones and the subsequent atmospheric dust dispersion have brought about many ecological and economical problems. This paper introduces a new approach to reduce pollutant emissions by simply changing pile configuration and without affecting the operational activity on these parks. Flow around piles of different geometries and for various wind conditions was studied using previously validated Computational Fluid Dynamic (CFD) simulations. Different pile height scenarios were investigated corresponding to a constant material volume and a fixed angle of repose under various wind magnitudes. The results obtained were integrated in order to evaluate the rate of dust emissions for the various configurations considered. It was found that, for the range of wind conditions and pile dimensions tested, an optimal geometry exists which corresponds to the lower emissions rate. 13 refs., 2 figs., 2 ...

2006-07-01

461

The similarity of twin brains  

International Nuclear Information System (INIS)

To test the assumption underlying every morphometric twin study that the brains of monozygotic twins are almost identical. Methods: High resolution MRI of the neurocranium of 26 monozygotic twin pairs were acquired and the volumes of 36 cerebral structures were measured. The same twins served as control group after rear-ranging them into non-related pairs of same sex and matching them for age, body height and body weight. Results: For most of the examined structures the correlations within the twins were significant (R = 0,97-0,59). Except for total forebrain volume the controls showed no significant similarity. Conclusions: For almost every measured cerebral structure the assumption, that significant similarities exist between healthy monozygotic twins is correct. Therefore discordant monozygotic twins represent an excellent sample when investigating cerebral correlates of neurologic and psychiatric disorders. (orig.)

2001-06-01

462

The kinematics of coronal mass ejections using multiscale methods  

CERN Document Server

The diffuse morphology and transient nature of coronal mass ejections (CMEs) make them difficult to identify and track using traditional image processing techniques. We apply multiscale methods to enhance the visibility of the faint CME front. This enables an ellipse characterisation to objectively study the changing morphology and kinematics of a sample of events imaged by the Large Angle Spectrometric Coronagraph (LASCO) onboard the Solar and Heliospheric Observatory (SOHO) and the Sun Earth Connection Coronal and Heliospheric Investigation (SECCHI) onboard the Solar Terrestrial Relations Observatory (STEREO). The accuracy of these methods allows us to test the CMEs for non-constant acceleration and expansion. We exploit the multiscale nature of CMEs to extract structure with a multiscale decomposition, akin to a Canny edge detector. Spatio-temporal filtering highlights the CME front as it propagates in time. We apply an ellipse parameterisation of the front to extract the kinematics ...

2009-01-01

463

Surface characteristics and overlaying properties of flat-pressed wood plastic composites  

British Library Electronic Table of Contents (United Kingdom)

This study evaluated surface characteristics and overlaying properties of wood plastic composite (WPC) panels made from dry-blended rubber wood fiber-polypropylene (PP) powder formulations using a conventional flat-press process under laboratory conditions. Three levels of rubberwood fibers (Hevea brasiliensis), 40%, 50%, and 60%, based on the composition by weight, were mixed with the PP powder without and with 3% (based on weight) maleic anhydride grafted PP (MAPP) as a coupling agent. Contact angle measurements on the WPC samples were performed using a goniometer connected with a digital camera which collected one image per second. Roughness measurements, average roughness (R a), mean peak-to-valley height (R z), and maximum roughness (R y), were taken from the sanded samples along and ...

2011-01-01

464

Some features of the atomic radial-distribution functions of metal glasses  

Energy Technology Data Exchange (ETDEWEB)

This paper attempts to explain the peculiarities of the radial-distribution function of metal glasses without involving ideas of the amorphous structure. On a computer, the radial atomic density for a spherical eutectic single crystal of the composition Fe/sub 84/C/sub 16/ of radius 15 A formed by alternating small crystals of e-Fe and Fe/sub 3/C of cubic form with the edge of the cube ca 10 A. For the sake of clarity, the diagram of such a quasisingle crystal is shown and has been given a cubic boundary. The change in the relationship between the heights of the subpeaks of the second maximum of the radial distribution function of atoms in the Fe-B glasses with a change in the concentration of boron can be explained by the change in the space group of the Fe/sub 3/B metastable boride which is formed in this system.

1986-09-01

465

Solids distribution in tall tanks  

British Library Electronic Table of Contents (United Kingdom)

Abstract Uniformly distributing slurry solids in -tall- (-2:1 aspect ratio) process vessels is a significant challenge in the chemical industry. This work determined the performance of various multi-tier agitation systems in uniformly distributing a settling solid throughout water in a -tall- laboratory vessel. It used a 0.445-m ID Plexiglas tank, with a slurry height of 0.889-m, to determine how solids distribution changes with solids loading (wt.%), impeller speed, and impeller type. Some impeller types uniformly distributed the solids even before energy input exceeded 1.00-W/kg. Significantly higher energy improved solids distribution little because flow within the vessel eventually became choked.

2011-01-01

466

Removal of scattered thermal neutrons using antiscatter grid  

International Nuclear Information System (INIS)

One of the significant factors of neutron radiographic image degradation is scattering blur from the object. A practical method is described to enhance image quality by eliminating the overlapping of scattered thermal neutrons component from the objects in ETRR-2 neutron radiography facility, using aluminum Gd-coated antiscatter grid. The MCNP code was used to determine the optimum grid dimensions that will reduce the scattered thermal neutrons from the object. An experiment was performed to determine the optimum grid height and irradiation time that gives the best image with acceptable geometric unsharpness. Using the MCNP code it was found that 97% of the scattered neutrons were removed by the grid. The wall dimensions and Gd coating are so small that the facility resolution cannot detect the image pattern superposition on the film.

2006-12-01

467

Redistribution of implanted dopants after metal-silicide formation  

Science.gov (United States)

The redistribution of implanted As and Sb following metal-silicide formation of Pt, Pd, and Ni has been studied. The phases of the silicides used were PtSi, Pd/sub 2/Si, and NiSi. Investigations with Rutherford backscattering analysis showed that after the formation of the silicides, the Sb was always found in the silicide layer near the surface of the samples, whereas PtSi and Pd/sub 2/Si caused a partial rejection of As for implanted doses of 2 x 10/sup 15/ cm/sup -2/ and higher. No rejection of As was found after the formation of NiSi. The results are discussed in terms of solid solubilities and impurity-metal compound formation. The data presented has implications in the fabrication of Ohmic contacts and the adjustments of the heights of Schottky barriers on silicon.

1978-12-01

468

Redistribution of implanted dopants after metal-silicide formation  

International Nuclear Information System (INIS)

The redistribution of implanted As and Sb following metal-silicide formation of Pt, Pd, and Ni has been studied. The phases of the silicides used were PtSi, Pd_2Si, and NiSi. Investigations with Rutherford backscattering analysis showed that after the formation of the silicides, the Sb was always found in the silicide layer near the surface of the samples, whereas PtSi and Pd_2Si caused a partial rejection of As for implanted doses of 2 x 10"1"5 cm"-"2 and higher. No rejection of As was found after the formation of NiSi. The results are discussed in terms of solid solubilities and impurity-metal compound formation. The data presented has implications in the fabrication of Ohmic contacts and the adjustments of the heights of Schottky barriers on silicon.

469

Recommended changes in meteorological measurement and prediction methods for coastal sites  

Energy Technology Data Exchange (ETDEWEB)

A study was performed to examine currently recommended meteorological measurement programs and atmospheric transport and diffusion prediction models for nuclear power plants to determine their adequacy for plants located in coastal zones where meteorological conditions are normally more complex than at inland sites and to make recommendations for changes to improve current procedures. Recommendations were based on an extensive literature review and on studies of coastal meteorology and diffusion. The study was focused on the following areas: coastal internal boundary layers; tower location; instrument heights; atmospheric stability classification; plume meander; and diffusion calculations. Each of the areas is discussed with appropriate recommendations which were made with respect to either the scientific or the regulation aspects of current procedures or both. Other potential problem areas are also pointed out.

1980-01-01

470

Power correlation for vertical axis wind turbines with varying geometries  

British Library Electronic Table of Contents (United Kingdom)

Abstract In this paper, a new predictive model that can forecast the performance of a vertical axis wind turbine (VAWT) is presented. The new model includes four primary variables (rotor velocity, wind velocity, air density, and turbine power output) as well as five geometrical variables (rotor radius, turbine height, turbine width, stator spacing, and stator angle). These variables are reduced to include the power coefficient (Cp) and tip speed ratio (TSR). A power coefficient correlation for a novel VAWT (called a Zephyr Vertical axis Wind Turbine (ZVWT)) is developed. The turbine is an adaptation of the Savonius design. The new correlation can predict the turbine's performance for altered stator geometry and varying operating conditions. Numerical simulations with a rotating reference f...

2011-01-01

471

Offshore hydraulics: tough, reliable, and failsafe  

Energy Technology Data Exchange (ETDEWEB)

The Offshore Comet is a modern offshore drilling rig with a hydraulic-cylinder-actuated jacking (raising and lowering) system. Hydraulic-cylinder jacking provides a safe and efficient method for placing the rig at the desired height above the water and insuring that it can withstand the expected heavy loads imposed by machinery, supplies, and the ocean environment. The drilling rig consists of a steel-hulled barge that is floated to the site and then supported during drilling operations by four steel triangular-cross-section lattice legs. The legs are planted firmly on the ocean bottom by a procedure called preloading. Each leg with its integral footing weighs 657 tons. The barge with its deck load can weigh up to 9200 tons.

1983-08-01

472

Offshore and inshore wave energy assessment: Asturias (N Spain)  

British Library Electronic Table of Contents (United Kingdom)

The offshore and inshore wave energy resource in Asturias (N Spain) is studied using wave buoy data and a hindcast dataset spanning 44 years (1958-2001). Offshore average wave power and annual wave energy values are found to exceed 30 kW/m and 250 MWh/m, respectively, at 7 of the 11 study sites. This substantial resource is characterised in terms of the sea states involved. Most of the energy is provided by IV quadrant waves with significant wave heights between 2 m and 5 m and energy periods between 11 s and 13 s. After analysing the offshore resource, numerical modelling is used to investigate the inshore wave patterns. A coastal wave model is validated with wave buoy data and applied to three case studies representative of storm, winter and summer conditions. Inshore wave energy concent...

2010-01-01

473

Nutritional state, maturational delay on electroencephalogram, and developmental outcome in extremely low birth weight infants  

British Library Electronic Table of Contents (United Kingdom)

The aim of this study is to clarify the relation among developmental outcome, nutritional state during the neonatal period, maturational electroencephalographic changes. Thirteen extremely low birth weight infants who completed 6- or 9-year follow-up were a subject of this study. Undernutrition was defined as enteral feeding below 100mL/kg/day at 3weeks of age. Dysmature patterns were defined as the persistence of EEG patterns 2weeks or more immature for post-conceptional age. IQ was examined at 6 and 9years of age. Body height and weight, and head circumference at 6years of age were stratified by the percentile grades. Full and verbal IQ was significantly lower in infants with undernutrition than those with normal nutrition. Among infants with undernutrition, those with persistent dysmatu...

2010-01-01

474

Nomographs for predicting crown fire initiation in Aleppo pine (Pinus halepensis Mill.) forests  

British Library Electronic Table of Contents (United Kingdom)

Nomographs that calculate the threshold values of surface fire parameters which lead to crown fire initiation were created by linking two separate fire behavior models: Van Wagner?s crown fire ignition criteria and Byram?s surface fire model. The nomographs were also based on the existing surface (fuel load, fuel heat content) and canopy (foliar moisture content, live crown base height) fuel models of Aleppo (Pinus halepensis Mill.) pine forests of Mediterranean Greece. The most important fire parameters for crown fire initiation that are calculated by the nomographs are the critical flame length and the forward spread rate of the surface fire. These parameters are readily observable in the field during fires. The nomographs provide a judicious way to assess whether a crown fire is likely ...

2007-01-01

475

New implementation of a shear-force microscope suitable to study topographical features over wide areas  

International Nuclear Information System (INIS)

A new implementation of a shear-force microscope is described that uses a shear-force detection system to perform topographical imaging of large areas (#approx#1x1 mm"2). This implementation finds very interesting application in the study of archeological or artistic samples. Three dc motors are used to move a sample during a scan, allowing the probe tip to follow the surface and to face height differences of several tens of micrometers. This large-area topographical imaging mode exploits new subroutines that were added to the existing homemade software; these subroutines were created in Microsoft VISUAL BASIC 6.0 programming language. With this new feature our shear-force microscope can be used to study topographical details over large areas of archaeological samples in a nondestructive way. We show results detecting worn reliefs over a coin.

2006-09-01

476

Meteorological measurement methods and diffusion models for use at coastal nuclear reactor sites  

Energy Technology Data Exchange (ETDEWEB)

A study, based on a literature review was made to examine currently recommended meteorological measurement programs and diffusion prediction methods for nuclear power plants to determine their adequacy for plants located in coastal zones. Although procedures for handling the near-worst case (stable, light-wind situation) were judged adequately conservative, deficiencies in guidelines and procedures were found with respect to the following: failure to consider the role of coastal internal boundary layers; specifications for tower locations and instrument heights; methods of classifying atmospheric stability; methods of allowing credit for plume meander, and models specified for diffusion calculations. Recommendations were made for changes in the guidelines applicable to these topics. Areas in which additional research is needed were identified.

1980-11-01

477

Mathematical modelling of air pollution in the Athens basin  

Energy Technology Data Exchange (ETDEWEB)

This paper presents research work concerning the mathematical modelling of air pollution in the Athens basin. A mathematical model based on aerodynamics and conservation equations together with turbulence modelling in body-fitted coordinates is used to provide the necessary input information to a similar but more detailed (i.e. small scale) model around Athens. Both models consist of solving the full Navier-Stokes equations and take into account the precise topography of the region. Different roughness heights are used for sea, coastal regions and land. The smaller scale model makes use of a two-equation turbulence model ({kappa}-{epsilon}) and the large scale model assumes a constant turbulence viscosity. The pollutant sources used in these models are based on actual emissions in the Athens area and are distributed in space. The results of this work appear promising and demonstrate the capability of the model as a tool for providing flow fields and pollution ...

1991-12-31

478

Liberalization, internationalization, and globalization: charting the course of foreign investment in the finance and commerce of Japan, 1945-2009  

British Library Electronic Table of Contents (United Kingdom)

As the world's largest creditor nation, with some of the world's largest banks and leading industries, Japan is often portrayed as an economic and financial superpower. With long-established 'Western-style' financial institutions to represent it in all the world's major financial capitals and markets, a technologically savvy Japan is often said to be positioning itself to lead Asia, the Asia/Pacific region, or even the entire world, into the marvels of the twenty-first century. Against this continuing rhetorical backdrop, however, fundamental questions arise as to Japan's ability to internationalize in today's increasingly globalized world economy. Domestically, only a very limited presence is permitted to the foreigner in the Japanese economy, especially in the commanding heights of finan...

2010-01-01

479

Large scintillation cells for high sensitivity radon concentration measurements  

Energy Technology Data Exchange (ETDEWEB)

Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alpha source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length without difficulty from insufficient pulse ...

1983-07-01

480

Large scintillation cells for high sensitivity radon concentration measurements  

International Nuclear Information System (INIS)

Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alphy source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length without difficulty from insufficient pulse ...

481

Kinesiological surface electromyography in normal children: Range of normal activity and pattern analysis  

British Library Electronic Table of Contents (United Kingdom)

To document the range of activity and patterns of normal surface kinesiological electromyography in normal children, 87 children ranging from age 3 to 18 years who were developing normally were evaluated at free walking speed. Analysis was performed on 6307 gait cycles from 11 different muscles with custom software. We devised an algorithm to do a computer-based KEMG curve pattern analysis to sort out curves that did not match the physiologic muscle activity pattern, We also devised a combined preset amplitude and statistics-based criteria to satisfactorily determine the onset/cessation of KEMG activity. The measurements of timing and duration of activity, body height and weight, body mass index, cadence, stride length, and age were obtained for statistical analysis. From the pattern recog...

2007-01-01

482

Interpolating atmospheric water vapor delay by incorporating terrain elevation information  

British Library Electronic Table of Contents (United Kingdom)

In radio signal-based observing systems, such as Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR), the water vapor in the atmosphere will cause delays during the signal transmission. Such delays vary significantly with terrain elevation. In the case when atmospheric delays are to be eliminated from the measured raw signals, spatial interpolators may be needed. By taking advantage of available terrain elevation information during spatial interpolation process, the accuracy of the atmospheric delay mapping can be considerably improved. This paper first reviews three elevation-dependent water vapor interpolation models, i.e., the Best Linear Unbiased Estimator in combination with the water vapor Height Scaling Model (BLUE?+?HSM), the Best Linear Unbiased Es...

2011-01-01

483

GPS impact on geodesy  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this paper is to check up a GPS (global positioning system) impact on scientific research activities of the Geodetic Society of Japan. First, it is mentioned that the conventional geoid-based concept of 'gravity anomaly' should be changed to a new definition, according to the GPS-determined ellipsoidal height system. Secondly, the results of many experiments, which have been made to monitor ocean-plate motions relative to the Japanese island-arcs, demonstrate that GPS is a powerful tool for obtaining temporal changes in horizontal displacement induced by the plate motion. Therefore, it is suggested that terrestrial measurements, such as triangulation and long-range leveling, would be replaced by GPS measurements in near future. Moreover, it is pointed out that GPS geodesy should play an important role in monitoring secular sea level trend due to global warming of the atmosphere and ocean. 19 refs., 4 figs.

1992-12-25

484

Flux enhancement options for an LEU-fueled MIT reactor  

International Nuclear Information System (INIS)

The Monte-Carlo transport code MCNP was used to evaluate possible arrangements of cores for the MIT Reactor using monolithic LEU fuel. Plate and moderator thicknesses were varied, and fixed absorbers and inner reflectors added in an effort to maximize available neutron fluxes at in-core and ex-core locations of experimental facilities. Addition of D_2O in the H_2O moderator was also evaluated. Comparisons of the fast, epithermal, and thermal fluxes were made at selected locations. Keff was also evaluated and critical blade heights compared with the existing HEU core. Results indicate that the LEU fluxes could approach HEU values with the use of a fueled in-core experimental facility, a fixed boron absorber spider and an inner beryllium reflector. (author)

2004-11-07

485

Development of a Full Body CAD Dataset for Computational Modeling: A Multi-modality Approach  

British Library Electronic Table of Contents (United Kingdom)

The objective of this study was to develop full body CAD geometry of a seated 50th percentile male. Model development was based on medical image data acquired for this study, in conjunction with extensive data from the open literature. An individual (height, 174.9?cm, weight, 78.6???0.77?kg, and age 26?years) was enrolled in the study for a period of 4?months. 72 scans across three imaging modalities (CT, MRI, and upright MRI) were collected. The whole-body dataset contains 15,622 images. Over 300 individual components representing human anatomy were generated through segmentation. While the enrolled individual served as a template, segmented data were verified against, or augmented with, data from over 75 literature sources on the average morphology of the human body. Non-Uniform Rational...

2011-01-01

486

Conformational analysis of ethyl azidoformate  

International Nuclear Information System (INIS)

A conformational analysis of ethyl azidoformate (EAF) has been carried out by the MINDO/3 quantum-chemical method. It has been shown that EAF exists in the form of two conformers differing with respect to rotation around the C-N bond. Complete optimization of the geometry has been carried out for both conformers. It has been found that the transoid conformation is planar and that the cisoid conformation is nonplanar. The height of the rotation barrier is 15.4 kcal/mole. The optimal geometry of the transition state has been calculated. It has been noted that a significant role in the mechanism of the conformational transition is played by the inversion of a nitrogen, which facilitates the transition. The results of the calculation have been confirmed by IR-spectroscopic data.

487

Comparison of Plasma Antioxidant Levels and Related Metabolic Parameters Between Smokers and Non-smokers  

British Library Electronic Table of Contents (United Kingdom)

The relationship between cigarette smoking and cell damage is complicated, particularly considering the role of oxidative stress. The aim of this study was to identify the relationships among plasma nicotine metabolites, lipophilic antioxidants, and metabolic parameters in smokers and non-smokers. This cross-sectional study recruited 100 subjects who visited the Department of Family Medicine at Kaohsiung Medical University Hospital. Excluding 14 ineligible cases, 46 smokers and 40 non-smokers were enrolled. Plasma nicotine metabolites, lipophilic antioxidants (including retinol, lycopene, a-carotene, b-carotene, d-tocopherol, g-tocopherol and a-tocopherol), related metabolic parameters, and body composition (including height, weight, body mass index, body fat, and waist circumference) were...

2009-01-01

488

Collection of athermal phonons into doped Ge thermistors using quasiparticle trapping  

Energy Technology Data Exchange (ETDEWEB)

We have developed a low-temperature particle detector that uses a novel quasiparticle trapping mechanism to funnel athermal phonon energy from an 80 mg Ge absorber into a 1.6 mg doped Ge thermistor via a superconducting Al film. We report on pulse height spectra obtained at 320 mK by scanning a {sup 241}Am alpha source along the device, and show that up to 20% of the energy deposited in the Ge absorber by a 5.5 MeV alpha particle interaction can be collected into a thermistor via quasiparticle trapping. We show that this device is sensitive to the position of an alpha particle interaction in the Ge absorber for interaction distances of up to 5 mm from a quasiparticle trap.

1995-05-15

489

Coherent Smith-Purcell radiation in the far-infrared region from a short-bunched electron beam  

International Nuclear Information System (INIS)

Coherent Smith-Purcell radiation, emitted from short-bunched electrons passing by a lamellar-type grating of aluminum, has been observed in the millimeter wave region. The energy of the electrons is either 42 MeV when they are accelerated by an L-band linear accelerator or 150 MeV accelerated by an S-band one. The intensity of the radiation is proportional to the square of the beam current. The radiation is linearly polarized, and the electric vector of the radiation is in the plane defined by the observing point and the beam trajectory. The intensity decreases with the beam height, i.e. the distance of the beam from the surface of the grating, in accordance with the modified Bessel function of zeroth order. copyright 1996 American Institute of Physics.

1995-09-28

490

Clinical and metabolic characteristics of polycystic ovary syndrome without polycystic ovary: a pilot study on Chinese women  

British Library Electronic Table of Contents (United Kingdom)

Objective To demonstrate clinical features of a patient subgroup presenting with polycystic ovary syndrome (PCOS) without polycystic ovary morphology. Design Retrospective study. Setting Hospital-based IVF center. Patient(s) In the present study, 876 PCOS patients were selected from women who visited the Reproductive Medicine Center at Shandong Provincial Hospital, Shandong University, between September 2004 and October 2006. Women with PCOS were divided into two groups based on ultrasound image: group A, PCOS patients with classic polycystic ovary (n = 800); group B, PCOS patients without polycystic ovary morphology (n = 76). The following available data were analyzed in the large cohort of women: body height, weight, waistline, hip circumference, hirsutism scores, family history, serum s...

2008-01-01

491

Cardiopulmonary fitness and endurance in children with developmental coordination disorder  

British Library Electronic Table of Contents (United Kingdom)

The purpose of this study was to compare cardiopulmonary fitness and endurance in 9-11-year-old children with DCD against a group of typically developing children in Taiwan. The Movement ABC test was used to evaluate the motor abilities of children. Forty-one participants (20 children with DCD and 21 children without DCD) were recruited for this study. The cardiopulmonary tests included the 800-m run test and the peak oxygen consumption (peak VO2) test using the Bruce treadmill protocol. No significant differences in age, body height, body weight, body mass index, and percentage of body fat between children with DCD and without DCD were found. However, there were significant differences in the cardiopulmonary endurance tests between children with DCD and without DCD. Children with DCD had ...

2010-01-01

492

Bioreactors  

Energy Technology Data Exchange (ETDEWEB)

Composting is once again gaining interest among ecological engineers in view of greener industrial and residential activities. Uniform composting is needed to ensure decomposition and to keep the whole system at the same composting stage. A homogeneous temperature must be maintained throughout the media. A bioreactor design consisting of a heater core made of copper tubing was designed and tested. Two four-inch holes were made at the top and bottom of the barrel to allow air to flow through the system and promote aerobic composting. Once composting began and temperature increased, the water began to flow through the copper piping and the core heat was distributed throughout the medium. Three thermocouples were inserted at different heights on a 200 litre plastic barrel fitted with the aforementioned apparatus. Temperature variations were found to be considerably lower when the apparatus was operated with the heat redistribution system, enabling uniform composting, ...

2010-07-01

493

Binary pseudo-random grating as a standard test surface formeasurement of modulation transfer function of interferometricmicroscopes  

Energy Technology Data Exchange (ETDEWEB)

The task of designing high performance X-ray optical systemsrequires the development of sophisticated X-ray scattering calculationsbased on rigorous information about the optics. One of the mostinsightful approaches to these calculations is based on the powerspectral density (PSD) distribution of the surface height. The majorproblem of measurement of a PSD distribution with an interferometricand/or atomic force microscope arises due to the unknown ModulationTransfer Function (MTF) of the instruments. The MTF characterizes theperturbation of the PSD distribution at higher spatial frequencies. Here,we describe a new method and dedicated test surfaces for calibration ofthe MTF of a microscope. The method is based on use of a speciallydesigned Binary Pseudo-random (BPR) grating. Comparison of atheoretically calculated PSD spectrum of a BPR grating with a spectrummeasured with the grating provides the desired calibration of theinstrumental MTF. The theoretical ...

2007-07-25

494

Assimilating remote sensing and in situ observations into a coastal model of northern South China Sea using ensemble Kalman filter  

British Library Electronic Table of Contents (United Kingdom)

Major forecast errors on the background error covariance from initial conditions, atmospheric forcing, model open boundary conditions, and the river discharges are examined in a coastal model of northern South China Sea. The analysis of background error covariance matrix produced by model ensemble shows that the perturbations of the initial conditions and atmospheric forcing play major roles in producing and maintaining the amplitude of ensemble spread except for the sea surface height (SSH) field. The perturbation of model open boundary conditions can influence ensemble spread of all variables and covariance between temperature and velocity or between temperature and SSH. The perturbation of river discharge mainly affects the covariance of salinity in river estuary. A data assimilation ex...

2011-01-01

495

Assessment of Low Quantitative Ultrasound Values of Calcaneus in Chinese Mainland Women  

British Library Electronic Table of Contents (United Kingdom)

Calcaneus quantitative ultrasound (QUS) assessment is a safe and reliable method for evaluating skeletal status. Until now, considerable data have been accumulated on the distribution of QUS in Caucasian populations, whereas such data are still insufficient in Asian populations, especially in Chinese mainland. The present study aimed to obtain the distribution characteristic of calcaneus QUS in healthy Chinese women, and to further investigate the distribution of low bone mass by QUS stiffness index (SI). This study included 2,498 healthy Chinese females aged 10-87 yr. The QUS exhibited a characteristic mild rise and then fall pattern with increasing age. Age, body height, and weight were significant influencing factors on SI, especially age and weight. The prevalence of osteoporosis detec...

2006-01-01

496

Aquaculture of Uranium in Seawater by a Fabric-Adsorbent Submerged System  

Science.gov (United States)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m{sup 3} in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m{sup 2} in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

2003-11-15

497

An investigation of the thermal performance of an oil filled transformer winding  

Energy Technology Data Exchange (ETDEWEB)

Manufacturers may be required to design transformers to overload specifications. Oil viscosity changes and loss variation with temperature are not accounted for in the industry loading guide. A comprehensive test program was performed using a winding assembly with imbedded thermocouples. Steady state and transient tests were performed for natural and non-directed forced oil circulation. The temperature distribution in the winding was not linear with height as usually assumed. A large number of temperature sensors is required to determine the hot spot location. The location of the hot spot was found to be different and less predictable for natural oil circulation compared with non-directed forced oil circulation especially during overload conditions. This paper reports that improved loading guide equations were developed to account for oil viscosity, resistance change, cooling duct oil rise, and location of the hot spot.

1992-07-01

498

A more detailed calculation of particle evaporation and fission of compound nuclei  

Energy Technology Data Exchange (ETDEWEB)

We consider particle evaporation and fission of an ensemble of hot, rotating compound nuclei as a stochastic process. We derive a set of coupled differential equations formed by a Fokker-Planck equation describing fission, and master equations for calculating particle evaporation. From these equations, we are able to determine multiplicities of prefission neutrons, protons and {alpha}-particles, their energy spectra and their angular momentum distributions. A comparison of our results with experimental data provides us with information regarding the reduced friction coefficient {beta}, the fission barrier height and the level density parameter. For different iridium isotopes, ({sup 181,185,187}Ir), {sup 185}Os and {sup 158}Er, we obtain as an upper limit {beta}{<=}8.0x10{sup 21} s{sup -1}. (orig.).

1991-07-15

499

A more detailed calculation of particle evaporation and fission of compound nuclei  

International Nuclear Information System (INIS)

We consider particle evaporation and fission of an ensemble of hot, rotating compound nuclei as a stochastic process. We derive a set of coupled differential equations formed by a Fokker-Planck equation describing fission, and master equations for calculating particle evaporation. From these equations, we are able to determine multiplicities of prefission neutrons, protons and #alpha#-particles, their energy spectra and their angular momentum distributions. A comparison of our results with experimental data provides us with information regarding the reduced friction coefficient #beta#, the fission barrier height and the level density parameter. For different iridium isotopes, ("1"8"1","1"8"5","1"8"7Ir), "1"8"5Os and "1"5"8Er, we obtain as an upper limit #beta##<=#8.0x10"2"1 s"-"1. (orig.).