General-Purpose Heat Source radioisotope thermoelectric generators (GPHS-RTGs) will provide electrical power for the NASA Galileo and European Space Agency (ESA) Ulysses missions. Each GPHS-RTG comprises two major components: GPHS modules, which provide thermal energy, and a thermoelectric converter, which converts the thermal energy into electrical power. Each of the 18 GPHS modules in a GPHS-RTG contains four /sup 238/PuO/sub 2/-fueled capsules. LANL conducted a series of safety verification tests on the GPHS-RTG before the scheduled May 1986 launch of the Galileo spacecraft to assess the ability of the GPHS modules to contain plutonia in potential accident environments. As a result of the Challenger 51-L accident in January 1986, NASA postponed the launch of Galileo; the spacecraft launch vehicle was reconfigured and the spacecraft trajectory modified. These actions prompted NASA to reevaluate ...
Anti-jamming techniques to improve Global Positioning System (GPS) receivers robustness have been mainly developed in military applications. None of civilian techniques can procure sufficient robustness against occasional or intentional jammers for civil GPS or GALILEO navigation receivers. The amplitude domain processing (ADP) filtering is a technique based upon Capon works and Neyman-Pearson theory. Several experiments concerning the ADP filtering have been considered at the 3DETSNAV division of LACIME laboratory at Ecole de technologie superieure (ETS), which have proved that the technique is reliable in order to eradicate powerful interference present in the spread spectrum signal. However, the results show that the ADP filter has a real limitation when submitted to multiple interferen...
In this paper, we report on the analysis of reverse flow in inverted U-tubes of a steam generator under natural circulation condition. The mechanism of reverse flow in inverted U-tubes of the steam generator with natural circulation is graphically analyzed by using the full-range characteristic curve of parallel U-tubes. The mathematical model and numerical calculation method for analyzing the reverse flow in inverted U-tubes of the steam generator with natural circulation have been developed. The reverse flow in an inverted U-tube steam generator of a simulated pressurized water reactor with natural circulation in analyzed. Through the calculation, the mass flow rates of normal and reverse flows in individual U-tubes are obtained. The predicted sharp drop of the fluid temperature in the inlet plenum of the steam ...
This chapter discusses the types of natural radioactive materials in the environment that include primordial natural radioactive materials such as K-40, U and Th, and daughters of their decay series. The discussion also includes secondary natural radioactive material generated through cosmic radiation interaction with nucleus of materials in the atmosphere. The dispersion of these radioactive materials to environment will also be part of the discussion. (Author)
The PGV-1000 secondary side natural circulation calculation results for steady-state operational conditions and their analysis using the data of actual NPP circulation investigation are presented. (3 refs., 3 figs., 3 tabs.).
The PGV-1000 secondary side natural circulation calculation results for steady-state operational conditions and their analysis using the data of actual NPP circulation investigation are presented. (3 refs., 3 figs., 3 tabs.).
In the presentation the major factors determining the conditions of NCC (Natural Coolant Circulation) in the primary circuit and in particular conditions of coolant rate distribution on the horizontal tubes of PGV-1000 in NPP with VVER-1000 under NCC are considered. 5 refs.
The presentation deals with the flows on the primary side of a horizontal steam generator under conditions typical to natural circulation cooling of the reactor. The main goal is to analyse the effect of primary flow patterns on the heat transfer capability of the steam generator. Conclusions pertinent to steam generator modelling with system codes are also drawn. (10 refs., 9 figs., 4 tabs.).
The presentation deals with the flows on the primary side of a horizontal steam generator under conditions typical to natural circulation cooling of the reactor. The main goal is to analyse the effect of primary flow patterns on the heat transfer capability of the steam generator. Conclusions pertinent to steam generator modelling with system codes are also drawn. (10 refs., 9 figs., 4 tabs.).
The interrelations between the factors causing the main effects on the primary circuit coolant flow rate distribution in the horizontal steam generator pipes in reactor facilities with the WWER type reactors under the modes with natural circulation are discussed. The criterion showing the presence or absence of coolant circulation reversal in bottom rows of the steam generator pipes is obtained. It is shown that large hydraulic non-uniformity in steam generator pipes operating in parallel under coolant natural circulation leads to decreasing the heat transfer surface efficiency under reactor facility emergency cooling, restricts its servicing capabilities. The circulation reverse in steam generator pipes under coolant natural circulation mode can give unfavourable effect on separate structural elements of the steam ...
Tests to measure the maximum horsepower of commercial vehicles converted for use with natural gas fuel indicate a reduction of approximately 20% in horsepower compared with gasoline-driven vehicles. This reduction in horsepower resulting from the use of gas is due basically to the lower thermal efficiency of the cycle of natural gas compared with that of gasoline and to its lower volumetric efficiency, since natural gas is injected into the combustion chamber in gaseous form, unlike gasoline, in which part of the fuel entering the cylinder is in the liquid phase. Natural gas used as a fuel generates lower quantities of air pollutants, particularly unburned hydrocarbons (HCs) and carbon monoxide (CO). Despite the downside of reduced horsepower, the use of natural gas as a fuel for automotive vehicles equipped with Otto-cycle engines is economically viable owing ...
The presentation gives a brief insight on possibility of using the VEERA facility in studying the stratification phenomenon. The idea for such experiments is to use the facility upper plenum part to simulate the conditions in upper part of horizontal steam generator hot collector. The upper part of steam generator hot collector is one of the locations where the stratification can take part during natural circulation mode. 4 refs.
SUMMARYTwo abundant classes of mobile elements, namely Alu and L1 elements, continue to generate new retrotransposon insertions in human genomes. Estimates suggest that these...Full Text Available
Phonological density refers to the number of words that can be generated by replacing a phoneme in a target word with another phoneme in the same position. Although the precise nature of the...Full Text Available
An approach to generate mimics of phosphorylated serine proteins chemically through site-specific sulfonation of cysteine is presented. This chemical modification is reversible in the presence of reducing agent and therefore is analogous to the kinase/phosphatase system used in nature. PMID:21717004
This work presents and describes the natural radioactive occurrence in oil facilities. The origins of the detected radioactivity and the reasons of its settlement are discussed. The measurements results carried out in oil facilities in the Neuquina basin (Argentine) are shown in this work. The aim is to describe the actual situation and to evaluate the magnitude of the problem. Finally, recommendations are proposed to protect the health of the workers, especially of those who carry out the cleaning of the equipment, and to guarantee an appropriate final disposal for the generated radioactive residuals. (author)
In this paper the possibility of using the test facility PACTEL concerning the investigations of thermal hydraulic special features of the primary coolant circuit acting under natural circulation is under consideration. It is suggested to study a stratification phenomenon of a coolant in upper plenum of a reactor and also a horizontal steam generator (HSG) hot collector temperature regime. For such investigations the facility must be modified. It is shown that this work is not large and expensive, as the facility is a lightly suitable unit for different researches. (orig.)
In this paper the possibility of using the test facility PACTEL concerning the investigations of thermal hydraulic special features of the primary coolant circuit acting under natural circulation is under consideration. It is suggested to study a stratification phenomenon of a coolant in upper plenum of a reactor and also a horizontal steam generator (HSG) hot collector temperature regime. For such investigations the facility must be modified. It is shown that this work is not large and expensive, as the facility is a lightly suitable unit for different researches. (orig.)
The experiments and the test facilities for the study of the stratification phenomenon in the hot plenum of reactor and the upper parts of the steam generator collectors in a nuclear power plant are described. The aim of the experiments was to define the conditions of the stratification initiation, to study the temperature field in the upper part, the definition of the characteristics in the stratification layer, and also to study the factors which cause the intensity of the stagnant volume cooling.
Experiments have been performed with the PMK integral-type facility, a model of WWER-440 type PWRs, to investigate two-phase natural circulation behaviour. The phenomena to be expected in this reactor type are different from those in PWRs with vertical steam generators mainly due to the loop seal in the hot leg and the horizontal layout of the steam generator heat transfer tubes. The experiments showed that the system is repressurized when the water level drops to the hot leg elevation due to the effect of the loop seal. Opening of the loop seal can be smooth, but may lead to oscillations depending on the power and the mass inventory. Natural circulation recovers after the hot leg loop seal is opened, but then decreases with further mass inventory decrease. (orig.).
The Earth`s troposphere and hydrosphere contain abundant naturallygenerated dust. The ultimate source materials from which the terrestrially produced dust is generated are the various rock types exposed at the Earth`s surface. Natural dust is a composite of (1) lithic, primary mineral grains; (2) mineral grains formed by secondary chemical reactions; (3) volcanic ash and dust; (4) salts from sea sprays; (5) extra-terrestrial dust; and (6) biologic materials. In this paper the various pathways to the naturalgeneration of dust (via the hydrologic cycle) will be discussed, and two geologically well-known natural dust sources will be described, paying particular attention to quantitative measurements of the dusts from these areas. General dust studies that provide data on possibly global background levels will be presented as well.. A few ...
The results of a study assessing natural-gas-fired combined-cycle (GFCC) power generation in the electric-utility sector are presented. This study quantified the economic benefits attributable to GFCC generation and examined the characteristics of GFCC technology that produce these benefits and the ways that these benefits vary among regions in the country. The impacts of changes in important economic parameters (capital cost, fuel price, etc.) as well as the impact of advances in GFCC technology were considered. Use of GFCC technology in the electric-utility sector could play an important role in a least-cost planning strategy and thereby provide significant benefits to the utilities and their customers. Potential benefits include reduced capital and operating costs, more effective matching of load growth and capacity additions, and greater system reliability. 8 refs., 3 tabs.
Rapid technology improvements, resulting in high efficiency, emissions reduction and low generation cost, are making gas turbines the generation technology of choice despite some recent reliability problems. The basic reason for the dominance is high efficiency. The rapid pace of gas-turbine technology improvement in the 1990s drove combined-cycle thermal efficiency to nearly 60 percent with natural gas as the fuel. It will probably go even higher after the year 2000. In addition, the gas-fired combined cycle is a bargain. With natural gas prices where they are right now, it is the least-cost generation operation for power producers with access to gas. Many will replace older, high-cost power plants with new gas-fired combined cycle power plants.
Australian electricity markets and natural gas markets are undergoing rapid reform. Choosing among electricity generation modes is a key issue. Such choices are affected by expectations about the future structure of these markets and future technologies, and how they affect costs and emissions. In the research reported in this paper, the MARKAL model of the Australian energy system is used to evaluate the competitive position of natural gas fired combined cycle gas turbines (CCGTs) in the energy sector as a whole. Competing in the sector are large-scale electricity generation technologies such as refurbished existing coal fired stations and advanced forms of coal fired generation. The modelling incorporates new data on electricity supply technologies and options.
This paper deals with the heat transfer characteristics of horizontal steam generators, particularly under natural circulation (decay heat removal) conditions on the primary side. Special emphasis is on the inherent features of horizontal steam generator behaviour. A mathematical model of the horizontal steam generator primary side is developed and qualitative results are obtained analytically. A computer code, called HSG, is developed to solve the model numerically, and its predictions are compared with experimental data. The code is employed to obtain for VVER 440 steam generators quantitative results concerning the dependence of primary-to-secondary heat transfer efficiency on the primary side flow rate, temperature and secondary level. It turns out that the depletion of the secondary inventory leads to an inherent limitation of the decay energy removal in VVER steam ...
Theoretical assessment on the chromatographic {sup 99m}Tc generator preparation using (n, {gamma}) {sup 99}Mo produced ex-natural molybdenum was carried out. The relationship between the neutron flux for MoO{sub 3} target activation, Mo-content or Mo adsorption capacity of column packing material, {sup 99m}Tc pertechnetate concentration and/or {sup 99m}Tc radioactivity of eluate was established. The reasonably lower limit of neutron flux of reactor and Molybdenum content of column packing material were found out to estimate the production of portable chromatographic generators available for nuclear medicine application. The concentration of {sup 99m}Tc pertechnetate eluate of low {sup 99m}Tc concentration using the column elution technique was also evaluate theoretically and conducted successfully in practice. Three options of {sup 99m}Tc generator using Titanium-Molybdate, Zirconium-Molybdate and ...
A calculation model was developed for the analysis of thermal and hydraulic processes in the PGV-1000 horizontal steam generator. The model makes it possible to examine the hydraulics of the primary medium, i.e., the distribution of flow velocities and mass flows in the exchanger tube system and hydraulic losses of the primary medium in the steam generator during its flow between the two connecting sites to the main circulation pipeline, spatial distribution of heat fluxes between the primary and secondary sides of the steam generator and the total transmitted thermal power, pressure on the secondary side of the generator, natural circulation of the working medium on the secondary side, and the mean circulation number, spatial distribution of the volume fraction of the steam component in the intertubular space, effect of the perforated sheet on the thermo-hydraulic processes in the ...
The outlook for natural gas (from both supply and price perspectives) has improved dramatically since the late 1970s, and significant advances have been made in electrical generation technologies which use gas. For example, gas-fired combined-cycle turbine units have become even more efficient and reliable. These units can be installed quickly (12 to 24 months versus 8 to 15 years for coal and nuclear units), and they may be brought on-line in small incremental blocks. This modular construction feature offers greater flexibility to utility planners, and the relatively low capital cost of combined-cycle units reduces financial uncertainties. The purpose of this chapter is to compare two electric power generating options, a new coal-fired powerplant and a new natural gas fired combined-cycle unit, from both economic and environmental perspectives. The comparison is based on a 240 megawatt baseload system.
Natural convection of vaporizing Deuterium at 25 K transports the heat generated in the moderator cell of the cold neutron source to a He cooled condenser. The thermohydraulics of this thermosiphon were precalculated and the results verified by experiments in a 1:1 model using D_2 as fluid. The experimental results show that the thermosiphon operates stable. The demanded liquid content of the cell as well as wall temperatures below 50 K can be ensured by a proper design of the cell outlet flow geometry. A 7 min. loss of cryogenic power results in transient temperatures of the cell wall of not more than 300 K.
The lateral natural frequency and vibration response analyses of the Large Scale Breeder Reactor (LSBR) primary pump were performed as part of the total dynamic analysis effort to obtain the fabrication release. The special features of pump modeling are outlined in this paper. The analysis clearly demonstrates the method of increasing the system natural frequency by reducing the generalized mass without significantly changing the generalized stiffness of the structure. Also, a method of computing the maximum relative and absolute steady state responses and associated phase angles at given locations is provided. This type of information is very helpful in generating response versus frequency and phase angle versus frequency plots.
Biogas supply to the public gas grid is a new option discussed in the most recent publication of Fachagentur Nachwachsende Rohstoffe (FNR) e.V. The biogas is purified, upgraded to natural gas quality and fed into an existing gas grid. Once there, it can be transported across long distances and also used for electric power generation at the consumer side. The study investigates inhowfar and in what instances this method is feasible and promising. It discusses the technical background and the regional potential of biogas. Seven model biogas systems are presented as examples. (orig.)
Silica-reinforced natural rubber (NR) composite was prepared by using tetraethoxysilane (TEOS) as a precursor to generate silica particles inside the rubber. The silica was generated in situ by the sol-gel process of TEOS that was mixed directly into commercial-graded NR latex having 60% dry rubber content and 0.7% ammonia. The conversions of TEOS to silica inside the rubber were ranging from 90 to 97%. The silica particles dispersed evenly without extensive aggregation with sizes between 100 and 500 nm, as determined by scanning electron microscopy (SEM). An experimental design methodology, namely "two-level factorial design," was used to evaluate the influence of the amounts of TEOS, ammonia, and gelation time on the tensile modulus, tensile strength, and tear strength of the vulcanizate...
This paper reports that there are four combustion technologies upon which U.S. electric utilities are expected to rely for the majority of their future power generating needs. These technologies are pulverized coal- fired combustion (PC); coal-fired fluidized bed combustion (AFBC); coal gasification, combined cycle systems (CGCC); and natural gas-fired combined cycle systems (NGCC). The engineering and economic parameters which affect the choice of a technology include capital costs, operating and maintenance costs, fuel costs, construction schedule, process risk, environmental and site impacts, fuel efficiency and flexibility, plant availability, capacity factors, timing of startup, and the importance of utility economic and financial factors.
In this context, the bulk ratio of CH4/N2 is examined as a potential alternative geochemical parameter for the assessment of thermal maturity of natural gas and compared to other previously published data. Open-system non-isothermal pyrolysis of low-mature coal from the Manjiaer sag, Tarim basin, yielded generation curves for methane and nitrogen. Analysis of the change of vitrinite reflectance indicates a two-stage process of thermal maturation with increasing temperatures. The relationship between Ro and pyrolysis temperature could be expressed by the following equations: Stage I: Ro = 0.0014T + 0.109, r = 0.9931(Ro Ro = 0.0067T -1.5855, r = 0.9996 (Ro > 0.6%). A kinetic interpretation of the characteristics of nitrogen and methane generation in humic coal during laboratory pyrolysis ind...
This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NO {sub X} , and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired plants. Global carbon dioxide emissions are lowered by 3% to 5%. Sulfur dioxide ...
This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NOX, and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired plants. Global carbon dioxide emissions are lowered by 3% to 5%. Sulfur dioxide emissions ...
The understanding of transport processes that occur in naturally fractured geothermal systems is far from being complete. Often, evaluation and numerical simulations of fractured geothermal reservoirs, are carried out by assuming equivalent porous media and homogeneous petrophysical properties within big matrix blocks. The purpose of this paper, is to present a comparison between results obtained from numerical studies of a naturally fractured reservoir treated as a simple porous medium and the simulation of some real aspects of the fractured reservoir. A general conclusion outlines the great practical importance of considering even approximately, the true nature of such systems. Our results show that the homogeneous simplified evaluation of the energy resource in a fractured system, could result in unrealistic estimates of the reservoir capacity to generate electricity.
The understanding of transport processes that occur in naturally fractured geothermal systems is far from being complete. Often, evaluation and numerical simulations of fractured geothermal reservoirs, are carried out by assuming equivalent porous media and homogeneous petrophysical properties within big matrix blocks. The purpose of this paper, is to present a comparison between results obtained from numerical studies of a naturally fractured reservoir treated as a simple porous medium and the simulation of some real aspects of the fractured reservoir. A general conclusion outlines the great practical importance of considering even approximately, the true nature of such systems. Our results show that the homogeneous simplified evaluation of the energy resource in a fractured system, could result in unrealistic estimates of the reservoir capacity to generate electricity.
Natural circulation experiments carried out in the REWET-III facility in 1985 have been used for RELAP5/MOD2 assessment. The REWET-III facility is a scaled-down model of VVER-440 type reactors. The facility consists of a pressure vessel in which the downcomer is simulated with an external pipe assembly, hot and cold legs with loop seals and a horizontal steam generator. The volume scaling factor compared to the reference reactor is 1:2333. The present paper summarizes the experiences gained in the RELAP5/MOD2 calculations of selected REWET-III single- and two-phase natural circulation experiments. The code's ability to represent the main phenomena of experiments in both cases was satisfactory.
Natural circulation experiments carried out in the REWET-III facility in 1985 have been used for RELAP5/MOD2 assessment. The REWET-III facility is a scaled-down model of VVER-440 type reactors. The facility consists of a pressure vessel in which the downcomer is simulated with an external pipe assembly, hot and cold legs with loop seals and a horizontal steam generator. The volume scaling factor compared to the reference reactor is 1:2333. The present paper summarizes the experiences gained in the RELAP5/MOD2 calculations of selected REWET-III single- and two-phase natural circulation experiments. The code`s ability to represent the main phenomena of experiments in both cases was satisfactory.
Natural circulation experiments carried out in the REWET-III facility in 1985 have been used for RELAP5/MOD2 assessment. The REWET-III facility is a scaled-down model of VVER-440 type reactors. The facility consists of a pressure vessel in which the downcomer is simulated with an external pipe assembly, hot and cold legs with loop seals and a horizontal steam generator. The volume scaling factor compared to the reference reactor is 1:2333. The present paper summarizes the experiences gained in the RELAP5/MOD2 calculations of selected REWET-III single- and two-phase natural circulation experiments. The code's ability to represent the main phenomena of experiments in both cases was satisfactory.
The thesis gives an overview of the validation process for thermal-hydraulic system codes and it presents in more detail the assessment and validation of the French code CATHARE for VVER calculations. Three assessment cases are presented: loop seal clearing, core reflooding and flow in a horizontal steam generator. The experience gained during these assessment and validation calculations has been used to analyze the behavior of the horizontal steam generator and the natural circulation in the geometry of the Loviisa nuclear power plant. Large part of the work has been performed in cooperation with the CATHARE-team in Grenoble, France. (41 refs., 11 figs., 8 tabs.).
CERN, DESY, Fermilab and SLAC have joined forces to build INSPIRE, the next-generation HEP information platform offering innovative tools for information discovery and communication. Representing a natural community-based evolution of SPIRES, INSPIRE provides fast access to the entire body of HEP literature. As a subject repository it will host fulltexts of preprints, Open Access journal articles and supplementary material like conference slides and multimedia, enabling novel text- and data mining applications. In the spirit of Web2.0 INSPIRE will also supply tools for collaboration and user-enriched content.
A nanoparticle generator based on the principle of electrical discharge (PALAS GFG-1000) was used to produce nanoparticles of different chemical natures. The fractions of electrically neutral particles were then measured by means of a Spectrometre de Mobilite Electrique Circulaire (SMEC, i.e. radial-flow mobility analyzer) for different operating conditions. The experimental results were compared with the theoretical values calculated from the Fuchs extended charge equilibrium model for spherical particles and agglomerates. For the smallest particles (below 20 nm), the deviations observed remain below 10%, and tend towards 20% for larger particles (over 35 nm).
The genetic type, source and charging history of natural gas in the Yulin gas field in the Ordos Basin have been studied by combining the carbon isotopic composition of natural gas and geochemical characteristics of light hydrocarbons with carbon isotope fractionation model results and fluid inclusion analysis. The carbon isotopic composition of methane and ethane in the Yulin gas field is relatively enriched in {sup 13}C with {delta}{sup 13}C{sub 1} values ranging from - 35.3 permille to - 29.8 permille (average value = - 32.4 permille) and {delta}{sup 13}C{sub 2} ranging from - 26.3 permille to - 23.5 permille (average value = - 24.8 permille). The C{sub 7} light hydrocarbons are predominated by methylcyclohexane, accounting for 65.8% to 80.9% (average value = 71.6%), which is characteristic of coal-derived gas. Furthermore, the gas geochemistry indicates that, although marine limestone source rocks are present in the region, the contribution ...
The seesaw-extended MSSM provides a framework in which the observed light neutrino masses and mixing angles can be generated in the context of a natural theory for the TeV-scale. Sneutrino-mixing phenomena provides valuable tools for connecting the physics of neutrinos and supersymmetry. We examine the theoretical structure of the seesaw-extended MSSM, retaining the full complexity of three generations of neutrinos and sneutrinos. In this general framework, new flavor-changing and CP-violating sneutrino processes are allowed, and are parameterized in terms of two $3\\times 3$ matrices that respectively preserve and violate lepton number. The elements of these matrices can be bounded by analyzing the rate for rare flavor-changing decays of charged leptons and the one-loop contribution to neutrino masses. In the former case, new contributions arise in the seesaw extended model which are not present in the ordinary MSSM. In ...
A multiprocessor architecture inspired by the Disney multiplane camera is proposed. For many applications, this approach produces a natural mapping of processors to objects in a scene. Such a mapping promotes parallelism and reduces the hidden-surface work with minimal interprocessor communication and low-overhead cost. Existing graphics architectures store the final picture as a monolithic entity. The architecture here stores each object's image separately. It assembles the final composite picture from component images only when the video display needs to be refreshed. This organization simplifies the work required to animate moving objects that occlude other objects. In addition, the architecture has multiple processors that generate the component images in parallel. This further shortens the time needed to create a composite picture. In addition to generating images for animation, the architecture has the ...
Nuclear options for electricity generations are assessed in this paper. Probabilistic (stochastic) method is used for economic comparison of nuclear power plants, wind plants and natural gas fired plants. Optimal nuclear power plant size is also discussed. IRIS is presented as a representative of small and medium reactors
The developments of fields in deep waters (5000 ft and more) is a common occurrence. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas-oil-and water possibly along with sand, hydrates, and wax...
As oil supplies diminish, Britain will have to rely more and more on coal as one of the energy alternatives. To burn coal cleanly and efficiently coal will have to be converted into gas and liquid fuels to replace natural gas and oil. The research and development programme of the National Coal Board is directed towards meeting these new challenges. This paper outlines some of the Coal Board's current projects in the fields of industrial combustion, power generation, domestic combustion, coal gasification and coal liquefaction. 10 figs.
An IR spectroscopic study of the reduction of copper-exchanged Linde Na-Y zeolite with hydrogen or carbon monoxide and oxidation with oxygen or oxygen-18 showed that copper(I) and AlO(+1) are formed during reduction, and that oxidation generates copper(II) ions but does not change the aluminum species. Trigonally coordinated aluminum was not detected.
A total of nine papers were presented at the course with the following titles: peat accumulation and coal basins; coal composition; coal quality; sedimentary environments of coal; generation, storage and migration of natural gas in coal bed reservoirs; geophysical log interpretation; the Ardley coal zone of central Alberta; stratigraphy and sedimentary environment of the Coalspur Formation; and the coal-bearing Luscar Group of western Alberta. All of these papers have been abstracted separately.
A drift dye tracer experiment, using Rhodamine (WT) dye, was conducted on airborne drift from a natural draft cooling tower at PEPCO's Chalk Point, Maryland Power Generating Station. This experiment was designed to separate and identify cooling tower aero...
This paper proposes a novel control strategy for tracking peak power in a wind or wave energy system using a squirrel cage induction generator. It eliminates wind speed measurement or estimation and uses a simple scalar technique by exploiting the cubic nature of the power curve. The method works even when air velocity is varying dynamically. (author)
Here we show that self-propulsion in quantum vacuum may be achieved by rotating or aggregating magneto-electric nano-particles. The back-action follows from changes in momentum of electro-magnetic zero-point fluctuations, generated in magneto-electric materials. This effect may provide new tools for investigation of the quantum nature of our world. It might also serve in the future as a "quantum wheel" to correct satellite orientation in space.
The suggestion has often been made that an additional radiation exposure imposed on humanity as a result of some important activity such as electricity generation would be acceptable if the exposure was 'small' compared to the natural background. In order to make this concept quantitative and objective, we propose that 'small compared with the natural background' be interpreted as the standard deviation (weighted with the exposed population) of the natural background. We believe that this use of the variation in natural background radiation is less arbitrary and requires fewer unfounded assumptions than some current approaches to standard-setting. The standard deviation is an easily calculated statistic that is small compared with the mean value for natural exposures of populations. It is an objectively determined quantity and its significance is generally ...
This paper was produced as an input to the Swiss Confederation's 'Electricity Perspectives 2035' study made by the Swiss Federal Office of Energy (SFOE). A concept for the combined use of wood and natural gas in a combined-cycle power station is presented. The gasification of wood to provide fuel for the gas turbines and waste-heat boilers of such power stations is proposed as an alternative to just burning wood to provide heat for steam generators. Figures are quoted on the quantities of biomass and wood usable for energy applications in Switzerland. The energetic and financial efficiencies of wood-powered generation of heat and electricity are examined, as are the investments necessary and the costs incurred. Comparisons are presented between wood from forests, sawmill-wastes, scrap wood and natural gas as fuels.
This report is an overview of Pacific Northwest Laboratory's (PNL) research on how hydroelectric generation affects aquatic biota and environments. The major accomplishments of this research are described, and additional work needed to permit optimal use of available data is identified. The research goals are to: (1) identify impacts of hydroelectric generation, (2) provide guidance in allocating scarce water resources, and (3) develop techniques to avoid or reduce the impacts on aquatic communities or to compensate for unavoidable impacts. Through laboratory and field experiments, an understanding is being developed of the generic impacts of hydrogeneration. Because PNL is located near the Columbia River, which is extensively developed for hydroelectric generation, it is used as a natural laboratory for studying a large-scale operating system. Although the impacts studied result from a ...
The hydro-generators suffer during its operative useful life a combination of stresses of nature thermal, electric, mechanics and environmental. With the time, they are going losing the capacity to support those stresses and the power plants suffer, more and more frequently, undesirable stops for repair services and maintenance. In function of the high costs incurred with these stopped, the operation of the power plant can be economically impracticable. That unavailability of the generation for the electric system, it results in reduction of the reliability, burdening the politics of load ruling. The re-potentiation is a proposal that seeks to extend the useful life of hydro-generators, at the same time that it try to rescue the reliability and the readiness of the plant, with larger power. The power increase is usually made possible, or for the surplus of the hydro resources in excess, or for the ...
This paper reports on the generator condition monitor (GCM) developed in an attempt to detect overheating inside large turbine generators. As part of a broader study on rotating machinery diagnostics, generator condition monitors were evaluated under field conditions in a 550 MW turbogenerator. Small 100 W resistors coated with insulating paints and varnishes were mounted inside the generator to simulate insulation overheating. The GCM responded very rapidly to an overheating event, typically within two minutes, even for hot spots as small s 10 cm{sup 2}. Similarly the aerosols produced on overheating were found extremely short lived, decaying within two to three minutes after overheating was discontinued. Use of heated ion chambers was found to desensitize the GCM regardless of the nature of the overheated insulation and in some cases would altogether prevent the GCM from reaching ...
The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle-natural gas fired system. A photovoltaic system still uses comparatively expensive ...
The numerous challenges facing the North American electric utility industry were discussed. In addition to competition, electric utilities are faced with low demand growth, public pressure to avoid adding transmission and distribution capacity, and strict environmental requirements. In view of these developments, large central generation additions that have been industry norm until recently, do not always make economic sense in the current environment. Instead, smaller, distributed additions to generating capacity is becoming the new norm. Small-scale on-site generating capacity has the added advantage of reducing the need for expensive high-voltage transmission lines. The Ballard generation system described here is a modular, efficient fuel cell-based solution to implementing distributed power concepts. The system is natural gas fueled, with low noise, vibration and emissions. ...
The presentation summarises the highlights of experimental results obtained for VVER type horizontal steam generator heat transfer, primary side flow pattern, and mixing in the hot collector during secondary side boil-off with primary at single-phase natural circulation. The experiments were performed using the PACTEL facility with Large Diameter (LD) steam generator models, with collector instrumentation designed specifically for these tests. The key findings are as follows: (1) the primary to secondary heat transfer degrades as the secondary water inventory is depleted, following closely the wetted tube area; (2) a circulatory flow pattern exists in the tube bundle, resulting in reversed flow (from cold to the hot collector) in the lower part of the tube bundle, and continuous flow through the upper part, including the tubes that have already dried out; and (3) mixing of the hot leg flow entering the hot collector and ...
Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 55% for electric power generation. Nevertheless the reserve of natural gas is more limited compared to the reserve of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverized coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, a catalyst, that converts carbon monoxide and unburnt carbon to ...
Mining operations took place at the Sullivan Mine, located at Sullivan, Abitibi, Quebec between 1930 and 1967 and generated large quantities of tailings. These tailings now represent a waste rock pile in the shape of a delta on the shore of De Montigny Lake. The area covers approximately 50 hectares. When the waste rock pile was first established, several terrestrial and aquatic ecosystems were lost forever. In addition, the very nature of the tailings, combined to the action of the wind and lake, further slow the natural site regeneration. The Ministere des Ressources naturelles du Quebec (Quebec Natural Resources Department) asked Les Consultants en Environnement Argus to prepare a site remediation plan to stimulate the natural regeneration of the ecosystems. It would enable the local fauna to resume its occupation of the territory, while ensuring its proper integration in the ...
The State of the Espirito Santo will become until the end of 2008, one of the main producers and natural gas exporters of Brazil, where, according to PETROBRAS, the State will produce about 20 million /day m{sup 3}, what it will go to contribute significantly for reduction of the dependence of the Bolivian gas, and still to give support to the natural gas sector in Brazil. The Intention of this work, is to identify proposals so that it has left of the gas produced in the State of the Espirito Santo, has a differentiated price. It does not make sensible the State to pay for the gas that is removed in its proper territory the same price that paid Sao Paulo for the gas that consumes imported of national Bolivia. With the markdown of the gas the State will be able to attract investments of great transport, to generate job and income and to advance in the question of the regional development that is of great importance for the ...
The increasing diffusion of small-scale energy systems within the distributed generation (DG) paradigm is raising the need for studying the environmental impact due to the different DG solutions in order to assess their sustainability. Addressing the environmental impact calls for building specific models for studying both local and global emissions. In this framework, the adoption of natural gas-fueled DG cogeneration technologies may provide, as a consequence of cogeneration enhanced overall energy efficiency and of natural gas relatively low carbon content, a significant reduction of global impact in terms of CO2 emissions with respect to the separate production of electricity and heat. However, a comprehensive evaluation of the DG alternatives should take into account as well the impact due to the presence of plants spread over the territory that could increase the local pollution, in particular due to CO and NOx, and ...
Mitsubishi is now developing a next-generation Pressurized Water Reactor (PWR) which has the innovative feature of hybrid safety systems (optimum combination of passive safety system and active safety system) and passive core cooling by horizontal steam generators during Loss of Coolant Accident (LOCA). In order to confirm the capability of this passive core cooling system during LOCAs, the thermal-hydraulic tests of horizontal steam generator and the integral thermal-hydraulic tests simulating the LOCAs were performed. The thermal-hydraulic tests of horizontal steam generator consist of a single tube test and a multi-tubes test. On the basis of these test results, the heat transfer characteristics of steam-water two-phase flow with noncondensable gas along a long horizontal tube is understood and the heat transfer correlation including the effect of noncondensable gas is presented. The integral ...
As a candidate of the new concept safety system for the next generation PWR in Japan, the hybrid safety systems, which are combination of the active and the passive safety systems, and passive core cooling system by natural circulation in the reactor coolant loop with horizontal-type steam generators during Loss of Coolant Accidents (LOCAs) are investigated. The passive safety systems are advanced accumulators (ACC), primary-side and secondary-side automatic-depressurization systems (ADS, SADS), and a gravity-driven safety injection system (GDI). The horizontal steam generator design avoids a siphon break caused from the accumulation of non-condensable gases in the tubes by using a vent line in the channel head of the steam generators. This study investigates the passive core cooling characteristics of horizontal-type steam generators under LOCAs. The integrated ...
OAK B188 The goal of this project is to mimic the energy transduction processes by which photosynthetic organisms harvest sunlight and convert it to forms of energy that are more easily used and stored. The results may lead to new technologies for solar energy harvesting based on the natural photosynthetic process. They may also enrich our understanding and control of photosynthesis in living organisms, and lead to methods for increasing natural biomass production, carbon dioxide removal, and oxygen generation. In our work to date, we have learned how to make synthetic antenna and reaction center molecules that absorb light and undergo photoinduced electron transfer to generate long-lived, energetic charge-separated states. We have assembled a prototype system in which artificial reaction centers are inserted into liposomes (artificial cell-like constructs), where they carry out light-driven ...
Total EU (and Norway) emissions of CO_2 from thermal power generation were some 950 million tonnes in 1990, the Kyoto agreement reference level. An ongoing research project, the GESTCO project, will provide the first documentation that, for the emission sources within the selected key areas, sufficient geological storage capacity is available for at least 30 years and possibly much longer. Cost of energy will obviously increase, but it is anticipated that electricity production cost price will be comparable to that of renewables. It would further have major implications for the European power generating industry which today is totally dominated by fossil fuel combustion with enormous emissions problems. The identification and siting of subsurface CO_2 storage capability can be expected to have considerable effect on the planning for and future siting of fossil fuel plants. In Norway there are plans to build several major, coastally sited, ...
Mineral deposition or alteration is commonly found at fracture-block interfaces is fissured, geothermal reservoirs. In response to pressure reduction in the fissures such mineralization, if less permeable than the matrix rock, will retard the flow of fluid from the blocks to the fissures and is termed fracture skin in this paper. The problem of fluid flow to a production well in a double-porosity reservoir with fracture skin was analyzed theoretically. One of the findings of the analysis was that fully transient block-to-fissure flow can be approximated by pseudo-steady state flow if fracture skin permeability is sufficiently low. Type curves generated by numerical inversion of Laplace transform solutions are used to cooroborate the results of a finite-difference model of steam transport to a well in a naturally fissured, geothermal reservoir with fracture skin.
The Environmental Protection Agency (EPA) is developing generally applicable environmental standards for land disposal of Atomic Energy Act (AEA) low-level radioactive wastes (LLW) and certain naturally occurring and accelerator-produced radioactive material (NARM) wastes. It is EPA's intention that the LLW standards will protect public health and the environment. The LLW standards would cover disposal of all AEA materials not controlled by other EPA standards and some natural radioactive materials. Coverage of federal waste is significant, because the federal government generates and disposes of >40% of all LLW nationwide, and a uniform standard for all LLW disposal is both a desirable and an achievable goal. Publication of a proposed LLW standard is planned in 1988, and a final standard a year later. This standard will have several important and closely related areas of focus which are discussed in the paper.
This remodeled form of Einstein's relativity theories retains and incorporates only experimentally proven principles. It is based on a generalized law for spinning and rotational motions, which is in fact the conservation law of momentum vector direction, and can be successfully used for the precision computation of planetary and lunar orbits. The most fundamental principles of the remodeled relativity theory are the conservation laws of energy and momentum. Based on experience of relativity experiments, we adopted the principles that energy level is the underlying cause for relativistic effects, and that mass is expressed by the relativistic energy equation from Einstein. From space age ephemeris generation experience and following nature's way to conserve energy and momentum, we found reason to replace the concept of "relativity of all frames" with that of "nature's preferred frame", which helped us to escape Einstein's ...
Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The model is also applied to industrial combustor geometries. (Author)
Inherent boron dilution can occur in case of a Small Break LOCA when low borated water is mainly accumulated in the U-legs due to reflux boiling in the Steam Generator tubes after the loss of natural circulation. The restart of the natural circulation may lead to criticality because of the injection of these low borated slugs towards the core. To evaluate this potential risk, the boron concentration at the core inlet has to be known which makes necessary to estimate the mixing phenomena in the cold leg, in the downcomer and in the lower plenum: CFD calculations are required. First of all the validation of CFX5 CFD code on the relevant phenomena of inherent boron dilution has been established (UPTF TRAM C3 test). Then, an application to the 900 MW French Pressurized Water Reactor series has been performed. (authors)
Operation and maintenance cost estimating methodologies for advanced coal-fired atmospheric circulating fluidized-bed and advanced natural gas-fired combined cycle electric power plants are presented. The purpose of these cost estimating relationships is for use in long range planning and evaluation of the economics of use of these technologies for electric power generation. Projected annual costs of reference plants at ten different sites in the United States, one in each of the ten DOE regions, are given as of 1989, and comparisons are made with existing technologies. A listing of a computer program implementing the methodologies is included. 14 refs., 4 figs., 13 tabs.
An investigation of current dual-fuel natural gas/diesel engine design, performance, and emissions was conducted. The most pressing technological problems associated with dual-fuel engine use were identified along with potential solutions. It was concluded that dual-fuel engines can achieve low NOx and particulate emissions while retaining fuel-efficiency and BMEP levels comparable to those of diesel engines. The investigation also examined the potential economic impact of dual-fuel engines in diesel-electric locomotives, marine vessels, farm equipment, construction, mining, and industrial equipment, and stand-alone electricity generation systems. Recommendations for further additional funding to support research, development, and demonstration in these applications were then presented.
Magnetic fields appear to be a generic feature of the early universe and are a natural source of secondary CMB non-Gaussianity. In recent years the statistical nature of the stresses of a primordial magnetic field has been well studied. In this paper we confirm and extend these studies at one- and two-point level, and present analytical results for a wide range of power-law spectra. We also consider two non-power law cases of interest: a blue spectrum with an extended damping tail on small scales, which could be generated by the non-linear mixing of density and vorticity; and a red spectrum with a damping tail on large scales. We then briefly consider the CMB impacts that result from such fields. While this paper focuses on the one- and two-point moments, the techniques we employ are designed to ease the analysis of the full bispectra induced by primordial magnetic fields.
Inherent boron dilution can occur in case of a small Break LOCA when low borated water is accumulated in the U-legs due to reflux boiling in the Steam Generator tubes after the loss of natural circulation. The restart of the natural circulation may lead to criticality because of the injection of these low borated slugs towards the core. To evaluate this potential risk, the boron concentration at the core inlet has to be known which makes necessary to estimate the mixing phenomena in the cold leg, in the downcomer and in the lower plenum: CFD calculations are required. First of all the validation of CFX5 CFD code on the relevant phenomena of inherent boron dilution has been established (UPTF TRAM C3 test). Then, an application to the 900 MW French Pressurized Water Reactor series has been performed. (authors)
The R&D in satellite communications in Korea has been driven mainly by KCC (Korea Communications Commission) but in a small scale compared to Korea space development program organized by MEST (Ministry of Education, Science and Technology). Public and civilian satcom sector R&D has been led mainly by ETRI with small/medium companies contrary to rare investment in private sector while military sector R&D has been orchestrated by ADD with defense industry. By the COMS (Communication, Ocean and Meteorological Satellite) experimental Ka-band payload, Korea pursues a space qualification of own technology for national infrastructure evolution as well as industrialization of space R&D results. Once COMS launched and space qualified in 2009, subsequent application experiments and new technology R&D like UHDTV will entail service and industry promotion. The payload technology is expected for the next Korean commercial satellites or for new OBP satellites. The COMS ground ...
The General-Purpose Heat Source (GPHS), an improved radioisotope heat source, employs a unique thermal insulation material, carbon-bonded carbon fiber (CBCF), to protect the fuel capsule and to help achieve the highest possible specific power. The CBCF insulation is made from chopped rayon fiber about 10 ..mu..m in diameter and 250 ..mu..m long, which is carbonized and bonded with phenolic resin particles. The CBCF shapes, both tubes and plates, are formed in a multiple molding facility by vacuum molding a water slurry of the carbonized chopped-rayon fiber (54 wt %) and phenolic resin (46 wt %). The molded shapes are subsequently dried and cured. Final carbonization of the resin is at 1600/sup 0/C. Machining to close tolerances (+-0.08 mm) is accomplished by conventional tooling and fixturing. The resulting material is an excellent lightweight insulation with a nominal density of 0.2 Mg/m/sup 3/ and a thermal conductivity of 0.24 W(m.K) in vacuum at 2000/sup 0/C. Several attributes ...
Nature of tube degradation was studied in support of horizontal steam generator lifetime calculations. Experiments were carried out to evaluate the resistance to environmentally assisted cracking (EAC) of steam generator tubes during operation. Estimations of the incubation period for crack initiation and the threshold K value, K(ISCC), and the crack growth rate were made to predict evolution of damage in tube walls. Experimental results were compared with in-service inspections experience. The paper summarizes results of experiments of C ring specimen for the initiation testing and results of SENT (single edge notch tensile) specimen for the crack growth rate (CGR) testing. The specimens were exposed to concentrated environments at elevated temperatures simulating crevice environments in secondary side crevices in horizontal steam generators. The results show that material of SG (steam ...
Nature of tube degradation was studied in support of horizontal steam generator lifetime calculations. Experiments were carried out to evaluate the resistance to environmentally assisted cracking (EAC) of steam generator tubes during operation. Estimations of the incubation period for crack initiation and the threshold K value, K(ISCC), and the crack growth rate were made to predict evolution of damage in tube walls. Experimental results were compared with in-service inspections experience. The paper summarizes results of experiments of C ring specimen for the initiation testing and results of SENT (single edge notch tensile) specimen for the crack growth rate (CGR) testing. The specimens were exposed to concentrated environments at elevated temperatures simulating crevice environments in secondary side crevices in horizontal steam generators. The results show that material of SG (steam ...
The nature of some baryonic resonances is still an unresolved issue. The case of the N{sup *}(1535) is particularly interesting in this respect due to the nearby {eta} N threshold and interference with the N{sup *}(1650). The N{sup *}(1535) has been described as a threshold effect, as a genuine 3-quark resonance, or as dynamically generated from the interaction of the octet of baryons with the octet of mesons. In the scheme of dynamical generation, predictions for the interaction of the N{sup *}(1535) with the photon can be made. In this study, we simultaneously analyze the role of the N{sup *}(1535) in the {pi}N{yields}{pi}N and {gamma}N{yields}{pi}N reactions and compare to the respective amplitudes from partial-wave analyses. This test is very sensitive to the meson-baryon components of the N{sup *}(1535). (orig.)
An overview of LOCA analysis in Japanese industry is presented. The BASH-M code, developed for large scale LOCA reflooding analysis, is given as an example of verification and improvement of US computer programs are given. The code's application to the operational safety analysis concerns the following main areas: 1D drift flux model base computer program CANAC; CANAC-based advanced training simulator; emergency operating procedures. The author considers also the code application to the following new PWR safety design concepts: use of steam generators for decay heat removal at LOCA conditions; use of horizontal type steam generator for maintaining two-phase natural circulation under the reactor coolant system submerged. 9 figs.
The LCLS, a Free-Electron Laser (FEL) designed for operation at a first harmonic energy of 300 eV ({lambda} {congruent} 40{Angstrom}) in the Self-Amplified Spontaneous Emission (SASE) regime, will utilize electron bunches compressed down to durations of <0.5ps, or lengths of <150 {mu}. It is natural to inquire whether coherent radiation of this (and longer) wavelength will constitute a significant component of the total coherent output of the FEL. In this paper a determination of a simple upper bound on the IR that can be generated by the compressed bunches is outlines. Under the assumed operating parameters of the LCLS undulator, it is shown that that IR component of the coherent output should be strongly dominated by the x-ray component.
We obtain and investigate the regular eigenfunctions of simple differential operators xr dr+1/dxr+1, r = 1, 2, ..., with the eigenvalues equal to 1. With the help of these eigenfunctions, we construct a non-unitary analogue of a boson displacement operator which will be acting on the vacuum. In this way, we generate collective quantum states of the Fock space which are normalized and equipped with the resolution of unity with the positive weight functions that we obtain explicitly. These states are thus coherent states in the sense of Klauder. They span the truncated Fock space without first r lowest-lying basis states: |0), |1), ..., |r - 1). These states are squeezed, sub-Poissonian in nature and reminiscent of photon-added states in Agarwal and Tara (1991 Phys. Rev. A 43 492).
In order to understand the parameters of the standard model of electroweak and strong interactions (coupling constants, masses, mixing angles) one needs to embed the standard model into some larger theory that accounts for the observed values. This means some additional sector is needed that fixes and stabilizes the values of the fundamental constants of nature. In these lecture notes we describe in nontechnical terms how such a sector can be constructed. Our additional sector is based on rapidly fluctuating scalar fields that, although completely deterministic, evolve in the strongest possible chaotic way and exhibit complex behaviour. These chaotic fields generate potentials for moduli fields, which ultimately fix the fundamental parameters. The chaotic dynamics can be physically interpreted in terms of vacuum fluctuations. These vacuum fluctuations are different from those of QED or QCD but coupled with the same moduli fields as QED and QCD ...
A chemical-looping process is proposed for the clean combustion of solid fuels for electric power or heat generation. The process is based on coal gasification with CO_2 to produce CO. The CO then reduces CaSO_4, which is used as an oxygen carrier, in a separate reactor to give CaS and CO_2. A portion of the CO_2 is recycled for the gasification stage and the rest can be sent for sequestration. The CaS is sent to another reactor for oxidation with air and to generate heat or power. The overall thermal effect is the same as direct combustion, but separation of CO_2 and other pollutants, such as sulphur, is achieved. In comparison with conventional chemical-looping combustion of natural gas, much less water is present in the CO_2 product, and hence the loss of heat energy and corrosion of the fuel-reactor system can be reduced.
Abstract Steam generation is an integral part of most chemical process plants; however, the steam plant often is or can be overlooked in the area of hazard analysis. The reasons for this oversight are obvious: steam generation is considered to be an old and well-understood process, and steam boiler systems are often not considered to pose the same hazards as other plant units. However, modern steam boiler systems are fueled with natural gas, pulverized coal, and/or fuel oil; each of which poses significant fire and explosion hazards. For example, a moderately sized chemical plant's boiler house may have two or three boilers operating at 240 MMBTU/hr, with each using approximately 11 ton/hr of subbituminous pulverized coal feed. Chemical plants rely on equipment design and installation, mai...
Deregulation and restructuring changes in the electric power industry have provided opportunities to build new power plants. These power plants, however, will not enjoy long-term power purchase agreements with the utilities they serve, but will have to respond to the market. This is where the term `merchant plant` originates. Calpine Corp. presented its reasons for believing that now is the best time to be building new merchant plants based on modern natural gas-fired, combined-cycle power plants. Among those reasons are: (1) construction of new nuclear power plants has been rejected by people on both sides of the border, (2) attempts to promote alternative energy sources such as solar, wind and biomass have not added significant generation capacity and are not likely to do so in the near future because of their high cost, and (3) coal-fired plants are also facing environmental challenges. For all these reasons, modern ...
Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 58% for electric power generation. Nevertheless the reserves of natural gas are more limited compared to the reserves of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverised coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, a catalyst, that converts carbon monoxide and unburnt carbon ...
This thesis consists of an introduction and five included papers. Of these, four papers are published in international journals and the fifth was submitted for review in April 2000. Emphasis has been placed on both naturally and artificially generated light hydrocarbons in petroleum fluids and their proposed source rocks as well as direct application of light hydrocarbons to oil/source rock correlations. Collectively, these papers describe a strategy for interpreting the source of the light hydrocarbons in original oils and condensates as well as the source of the asphaltene fractions from the reservoir fluids. The influence of maturity on light hydrocarbon composition has also been evaluated. The papers include (1) compositional data on the light hydrocarbons from thermal extracts and kerogen pyrolysates of sediment samples, (2) light hydrocarbon data of oils and condensates as well as the pyrolysis products of the asphaltenes from these ...
A molybdenum (Mo) adsorbent called PZC (Poly Zirconium Compound) with high efficiency of Mo adsorption has been developed in order to generate {sup 99m}Tc from {sup 99}Mo produced from natural Mo by (n, gamma) method. The {sup 99m}Tc generator using PZC has cleared mostly the technical subjects. By the results of many experiments, cold and hot test with {sup 99}Mo activity from low level (10{sup 5} Bq) to high level (10{sup 10} Bq), it has been confirmed that the PZC method can be practically applied for the (n, gamma) {sup 99}Mo-{sup 99m}Tc generator. From the reasons that PZC has the ability and many merits such as high adsorption capacity (>250 mg-Mo/g-PZC) of Mo, high elution yield (av. 80%) of {sup 99m}Tc, the low breakthrough (<0.05 kBq-{sup 99m}Mo/MBq-{sup 99m}Tc) of {sup 99}Mo and others, the current (n, fission) {sup 99m}Tc generator utilizing {sup 99}Mo ...
The research has involved the characterization of catalyst acidity, [sup 2]D NMR studies of Bronsted acid sites, and kinetic, calorimetric, and spectroscopic studies of methylamine synthesis and related reactions over acid catalysts. Approach of this work was to explore quantitative correlations between factors that control the generation, type, strength, and catalytic properties of acid sites on zeolite catalysts. Microcalorimetry, thermogravimetric analysis, IR spectroscopy, and NMR spectroscopy have provided information about the nature and strength of acid sites in zeolites. This was vital in understanding the catalytic cycles involved in methylamine synthesis and related reactions over zeolite catalysts.
The purpose is to define sustainable economic development in the context of nonrenewable resources and to examine the changing nature of reclamation over time. Sustainable development is development that ensures the present utilization of resources and the environment does not damage prospects for their use by future generations. Polls show that the public is demanding higher environmental standards. One mechanism for achieving sustainable economic development for the nonrenewable resource sector is through reclamation. The Alberta government`s approach to reclamation is reviewed to show how reclamation and sustainable government are linked together. The history of reclamation legislation in Alberta is summarized. 10 refs.
Utility interest has recently increased in potential future nuclear units that combine the characteristics of smaller size, greater simplicity, and more passive safety features. In response to such interest, General Electric (GE) began development in 1982 of a 600-MW(electric) reactor with simplified power generation and safety systems. This paper provides an overview of the simplified boiling water reactor (SBWR) design, with emphasis on the thermal-hydraulic aspects of the design. The SBWR is a natural circulation reactor requiring no pumps to circulate the water through the core.
We apply the group theory to Kadomtsev-Petviashvili-Burgers (KPBII) equation which is a natural model for the propagation of the two-dimensional damped waves. In correspondence with the generators of the symmetry group allowed by the equation, new types of symmetry reductions are performed. Some new exact solutions are obtained, which can be in the form of solitary waves and periodic waves. Specially, our solutions indicate that the equation may have time-dependent nonlinear shears. Such exact explicit solutions and symmetry reductions are important in both applications and the theory of nonlinear science.
A self contained continuous power generation system as described at INTELEC 1979, was successfully commissioned and put into service in a major communications centre at Cardiff in Wales. The objective was to provide all telecommunications equipment and electrical building engineering services from a dual fuel enginegenerating plant, and to recover waste heat energy to heat or cool the building. The plant, which is fully automatic, comprises five 1300kW engines using natural gas or diesel oil, and associated waste heat boiler and chiller systems. This paper reviews the functioning of the plant during its first three years of operation.
The nature of the first generation of stars in the Universe remains largely unknown. Observations imply the existence of massive primordial stars early in the history of the universe, and the standard theory for the growth of cosmic structure predicts that structures grow hierarchically through gravitational instability. We have developed an ab initio computer simulation of the formation of primordial stars that follows the relevant atomic and molecular processes in a primordial gas in an expanding universe. The results show that primeval density fluctuations left over from the Big Bang can drive the formation of a tiny protostar with a mass of just one percent that of the sun. The protostar is a seed for the subsequent formation of a massive primordial star.
Knock limitations are investigated using natural gas, with diesel pilot ignition, as a fuel for the 3406 DI-TA Caterpillar diesel engine. Thermodynamic properties at TDC are generated by computer and compared with experimental results. Exhaust emissions are analyzed. A comparison is made of dual-fuel operation relative to diesel. Observations are made to determine the onset of knock. The onset of knock is characterized as a function of engine speed, load, inlet manifold temperature, and air-fuel ratio (A/F). The conditions at the inset of knock are determined using cylinder pressure data. The most efficient operating range is determined with knock avoidance as a prime parameter.
Cesium-137 has contaminated a large area of the wetlands on the Savannah River Site. Remediation of the contaminated wetlands is problematic because current techniques destroy the sensitive ecosystem and generate a higher dose to workers. To address this problem, we proposed a non-trusive, in situ technology to sequester 137Cs in sediments. One intention of this study was to provide information regarding a go/no go decision for future work. Since the proof-of-concept was successful and several minerals were identified as potential candidates for this technology, a go decision was made.
We entertain the idea that a suitable background of cold (very low momentum) pseudoscalar particles or condensate, may trigger a background that effectively generates Lorentz-invariance violation. This aether-like background induces a Chern-Simons modification of QED. Physics is different in different frames and, in the rest frame of the pseudoscalar background, high momentum photons can decay into pairs. The threshold for such decay depends quadratically on the rest mass of the particles. This mechanism could explain in a natural way why antiprotons are absent in recent cosmic ray measurements. A similar signal could be used as a probe of pseudoscalar condensation in heavy ion collisions.
Because of the stochastic nature of traffic requirement matrix, it is very difficult to get the optimal traffic distribution to minimize the delay even with adaptive routing protocol in a fixed connection network where capacity already defined for each link. Hence there is a requirement to define such a method, which could generate the optimal solution very quickly and efficiently. This paper presenting a new concept to provide the adaptive optimal traffic distribution for dynamic condition of traffic matrix using nature based intelligence methods. With the defined load and fixed capacity of links, average delay for packet has minimized with various variations of evolutionary programming and particle swarm optimization. Comparative study has given over their performance in terms of converging speed. Universal approximation capability, the key feature of feed forward neural network has applied to predict the flow ...
The main objective of the present study is to investigate Turkey's natural gas (NG) demand and supplies by giving the structure of the Turkish gas industry, NG pricing policy, and NG agreements. Turkey began to import NG from Russia in 1987 under a contract that provided for the delivery of 6 billion cubic meters annually (Bcma) for 25 years. The first contract, signed in 1988, stipulates delivery of 2 Bcma over a 20-yr period. The build-up of the Turkish gas market started by introducing gas in power generation in 1987 and in fertilizer production in 1988. Later contracts provide for total imports of 4 Bcma from the late 1990s. NG sales started at 0.5 Bcm in 1987 and reached to around 16 Bcm in 2001. Turkish NG demand is projected to increase extremely rapidly in coming years, with the prime consumers expected to be NG-fired electric power plants and industrial users. (author)
The natural convection characteristics of gas in a vertical narrow annular gap which had its bottom opened to high temperature fluid and its upper shielding exposed to low temperature sealant have been evaluated from simulated fluid experiments using water and from calculations using the three-dimensional thermal hydraulic analysis computer code THERVIS-III. The following results were obtained: (1) The critical Rayleigh number which represented the limit of convection generation increased as the aspect ratios #epsilon#_1 (height/circumference) and #epsilon#_2 (height/gap distance) increased. (2) The flow pattern along the circumferential direction was seen to depend more strongly on the radiant heat from the side wall, rather than the aspect ratios #epsilon#_1 and #epsilon#_2. (3) The temperature difference along the circumferential direction in the annular gap obtained from the calculation code coincided with that obtained from experiments ...
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary experiments in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The experiments were run on the Parallel Channel Test Loop (PACTEL), which is a medium scale integral test facility designed to simulate thermal-hydraulic phenomena characteristic of VVER 440 type nuclear plants. The experiments aimed at studying the effect of noncondensable gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators (ACCU) released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any noncondensable gas in all cases where cooling is ensured by natural circulation. This paper presents the measured results of the series of three ...
Naturally occurring radionuclides are present in most material. The most common naturally occurring radionuclides in material are those of the uranium and thorium series and potassium-40. This material is commonly referred to as Naturally Occurring Radioactive Material (NORM). In some material the levels of naturally occurring radionuclides are significantly higher, to the extent that regulatory control may be required for radiation protection purposes. Regulation of NORM presents a range of new challenges for both regulators and operators. Unlike more traditional industries dealing with radionuclides, NORM industries have generally not had any radiological oversight and, for example, are not equipped for radiological monitoring. Some consumer goods containing NORM, which have not traditionally been considered as a radiological problem (such as some fertilizers), may require regulation and this may have ...
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary tests in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The tests aimed at studying the effect of NC gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any NC gas in all cases where cooling is ensured by natural circulation. A secondary objective of the tests - the first series of tests ever performed with NC gas with PACTEL - was to find out, if the instrumentation of PACTEL was adequate for this type of tests and if it was functioning properly. This paper presents the measured and calculated (CATHARE code version V15a mod 2.1) results of the test ...
Electricity generation from natural gas in gas turbine units can be made substantially more efficient by preliminary methane conversion to a synthesis gas containing hydrogen and carbon monoxide and/or by the use of some of the synthesis gas produced in industry. An alternative improvement involves the introduction of solid oxide fuel cells (SOFCs) and the use of the synthesis gas in them. In this study, a modified scheme of gas turbine cycle that includes an SOFC, a membrane reactor (instead of a traditional combustion chamber), and a catalytic reactor to perform methane conversion to produce hydrogen (synthesis gas) is proposed. Variations of the energy and exergy efficiencies of the integrated system with operating conditions are provided, showing, for example, that SOFC efficiency is enhanced if the fuel cell active area is augmented. The SOFC stack efficiency can be maximized by reducing the steam generation while ...
This paper reports that the point defect model for steady-state passive films formed anodically on metal s in aqueous environments has been extended to include irreversible dissolution of the film and the irreversible generation and annihilation of cation and oxygen vacancies at the metal/film and film/solution interfaces. THe model yields a number of diagnostic criteria that can be used to identify the majority (vacancy) charge carrier and to characterize the kinetic nature of the interfacial vacancy generation and annihilation processes. We use these criteria to show that the steady-state passive film that forms on nickel in acidic phosphate buffer solutions is a cation conductor and that cation transport from the metal to the solution involves irreversible ejection of cations from the film. On the other hand, the passive film that forms on tungsten in the same environment under steady-state conditions is found to be an ...
The report outlines the role of the IEA Greenhouse Gas R and D Programme, gives details of participants and of publications and summarises achievements of 1998. A successful conference on Greenhouse Gas Control Technologies was held in Interlaken, Switzerland. Technical studies reported include novel power generation concepts for removing carbon dioxide prior to or after combustion, using seawater for CO{sub 2} capture, investigating carbon dioxide sequestration in conjunction with enhanced coalbed methane recovery and applying retrofitting to power plants and to offshore oil and gas platforms. Systems studies taking a broader view include investigating the potential for combined energy systems (power generation with district heating, power with district cooling etc.) to reduce CO{sub 2} abatement cost, studies on the LNG/power generation fuel cycle, assessing the potential of methanol as an energy carrier investigating ...
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency have been established.
A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency have been established.
This report describes in detail the First Generation Duct Injection Model developed for the analysis of the fundamental processes of flue gas desulfurization by sorbent injection. The model is a two- and three-dimensional, multiphase reacting flow analyzer using computational fluid dynamics methods. The gaseous phase is solved in an Eulerian frame while the droplets or particles are tracked in a Lagrangian frame. The model has an associated preprocessor which allow easy problem set up by the use without in-depth knowledge of computational fluid dynamics. The aerodynamics of the First Generation Duct Injection Model have been successfully validated with a number of test cases for which experimental data are available. Data from the Meredosia pilot plant humidification tests have been used to validate the gas and droplet dynamics of the model with good agreement. Comparison of SO{sub 2} removal results using the present model (with one injector) ...
The terrestrial biosphere can significantly affect the exchange of water and energy at the biosphere-atmosphere interface. Additionally, the land cover type can affect regional atmospheric chemistry and climate via biogenic volatile organic carbon (VOC) emissions and their formation of secondary organic aerosols. The broad goal of this study is to investigate the impact of land cover and vegetation changes on these specific chemistry and climate effects. The Common Land Model (CLM) is used to parameterize the biosphere-atmosphere interface over the Shanghai region in China. Phase 1 of this study, described in this report, generates input parameters for this model based on a time series of actual and derived parameters. Atmospheric forcing data are generated on an hourly temporal resolution based on a 20-year series of monthly and daily averages. Surface data, including land cover/land use and soil information, are generated ...
This paper describes the use of numerical analysis for studying natural convection cooling systems for long term storage of heat producing radioactive materials, including special nuclear materials and nuclear waste. The paper explains the major design philosophy, and shares the experiences of numerical modeling. The strategy of storing radioactive material is to immobilize nuclear high-level waste by a vitrification process, convertion it into borosilicate glass, and cast the glass into stainless steel canisters. These canisters are seal welded, decontaminated, inspected, and temporarily stored in an underground vault until they can be sent to a geologic repository for permanent storage. These canisters generate heat by nuclear decay of radioactive isotopes. The function of the storage facility ventilation system is to ensure that the glass centerline temperature does not exceed the glass transition temperature during storage and the vault ...
Natural cooling conditions of the nuclear fuel in the channel type reactor after its shut down are commonly determined with relatively high uncertainty. This is not only to he lack of adequate measurements of thermal parameters i.e. the residual power generation, the coolant flow and temperatures, but also due to indeterminate model of convection mechanism. The numerical simulation of natural convection in multitube fuel assembly in the fuel channel leads to various convection modes including evidently chaotic behaviour. To determine the real cooling conditions in the MARIA research reactor a series of experiments has been performed with fuel assembly equipped with a set of thermocouples. After some forced cooling period (the shortest was half an hour after the reactor shut down) the reactor was left with the only natural convection. Two completely different cooling modes have been observed. The MARIA ...
The general strategy for improving the safety of nuclear power plant and its economics is to accomplish power uprates while securing sufficient thermalhydraulic margin. In order to succeed this strategy, there have been a lot of efforts in increasing the margin through the enhancement of heat transfer capability in coolants. However, despite their efforts, only about 10 {approx} 15 % increase of the thermal margin is possible by using the best art known well up to now with installation of mechanical engineering devices such as mixing vane or button to generating the swirl flow and turbulent mixing. The limit of the capability of the best technique has made a lot of engineers to be frustrated to do the power uprates. Nevertheless, fortunately a new innovative idea is being proposed in heat transfer community as an engineering colloidal fluid to basically change the original properties of the coolant. The fluid began to be called by Choi as a nanofluid which is a ...
Off-grid power generation is meant to supply remote or rural area, where grid connection is almost impossible in terms of cost and geography, such as island, aborigine's villages, and areas where nature preservation is concern. Harnessing an abundance renewable energy sources using versatile hybrid power systems can offer the best, least-cost alternative solution for extending modern energy services to remote and isolated communities. The conventional method for off-grid power generation is using diesel generator with a renewable energy (RE) technology utilizing solar photovoltaic, wind, biomass, biogas and/or mini/micro hydro. A hybrid technology is a combination of multiple source of energy; such as RE and diesel generator and may also include energy storage such as battery. In our design, the concept of solar hybrid system is a combination of solar with diesel genset and battery ...
CRE is the French commission for energy regulation. CRE's remit is to assist in ensuring the proper operation of the electricity and natural gas markets for the benefit of the end-user. In particular, CRE ensures that the conditions of access to electricity and natural gas transmission and distribution systems do not hinder the development of competition. It monitors, for the electricity and natural gas sectors, all transactions made between suppliers, traders and producers, all transactions made on the organised markets and cross-border trading. It ensures that suppliers, traders and producers propose offers that are consistent with their financial and technical constraints. It monitors the implementation of and compliance with regulations giving consumers the right to choose their supplier in a competitive market, and allowing new suppliers to enter the market. This document is the 2008 activity report of CRE. ...
An advanced experimental technique has been developed to simulate two-phase flow behavior in a light water reactor (LWR). The technique applies three kinds of methods; (1) use of sulfur-hexafluoride (SF6) gas and ethanol (C2H5OH) liquid at atmospheric temperature and a pressure less than 1.0MPa, where the fluid properties are similar to steam-water ones in the LWR, (2) generation of bubble with a sintering tube, which simulates bubble generation on heated surface in the LWR, (3) measurement of detailed bubble distribution data with a bi-optical probe (BOP), (4) and measurement of liquid velocities with the tracer liquid. This experimental technique provides easy visualization of flows by using a large scale experimental apparatus, which gives three-dimensional flows, and measurement of detailed spatial distributions of two-phase flow. With this technique, we have carried out experiments simulating two-phase flow behavior in a single-channel ...
Important steady-state thermohydraulic parameters of the TRIGA research reactor operating under natural convection mode of coolant flow were investigated using NCTRIGA computer code. Neutronic parameters used in preparing the input of NCTRIGA were taken from the analysis performed by 3-D Monte Carlo code MCNP4C. Benchmarking of the NCTRIGA calculated results were performed against the experimental data measured by the thermocouples in the instrumented fuel element (IFE) during the steady state operation of the reactor under natural convection mode of coolant flow. Various thermohydraulic parameters like the coolant velocity, flow rate and mass flow rate were generated for the hot channel as well as for the two channels comprising instrumented fuels. Calculated peak fuel temperatures at different power levels were compared with the measured values and also with the calculations performed by PARET code. Axial temperature ...
Developing safe, reliable, cost-effective, and efficient hydrogen-electricity co-generation systems is an important step in the quest for national energy security and minimized reliance on foreign oil. This project aimed to, through materials research, develop a cost-effective advanced technology cogenerating hydrogen and electricity directly from distributed natural gas and/or coal-derived fuels. This advanced technology was built upon a novel hybrid module composed of solid-oxide fuel-assisted electrolysis cells (SOFECs) and solid-oxide fuel cells (SOFCs), both of which were in planar, anode-supported designs. A SOFEC is an electrochemical device, in which an oxidizable fuel and steam are fed to the anode and cathode, respectively. Steam on the cathode is split into oxygen ions that are transported through an oxygen ion-conducting electrolyte (i.e. YSZ) to oxidize the anode fuel. The dissociated hydrogen and residual steam are exhausted from ...
The Burrard Thermal Generating Station is located at Port Moody, British Columbia, and burns natural gas to supply steam to six turbine units for generating up to 912 MW of electricity. The Burrard plant accounts for ca 8.7% of the provincial generating capability. Burrard is expected to continue to fill a vital role as a supplier of displaceable firm energy to the British Columbia Hydro system. In parallel with a renewed focus on Burrard from a system planning perspective, there have also been concerns about air pollution from the plant in the context of its possible effect on the region's air quality. To address this and other issues surrounding Burrard's future, B.C. Hydro established a project team to conduct a utilization study. The team's work focused on the role of Burrard in providing a reliable and profitable role in electricity generation, the ...
Analyzing various SBLOCA with high pressure safety injection (HPSI) at VVER-440/213, we met a surprising phenomenon - a 'natural' circulation post SG heat transfer reversal. This is not usual, because normal natural circulation (NC) in primary circuit is connected with positive heat transfer at SG. If there is reverse heat transfer at SG (as soon as the break enthalpy outflow is sufficient for removal of reactor decay heat), it should obstruct any natural circulation. The question was, what is the driving force of this 'non-standard natural circulation'. After all we revealed that force - it is the density difference between the colder water in reactor downcomer (cold water from HPSI) and warmer water in inner reactor (lower plenum, core, upper plenum). This phenomenon could be confusing for operating personal, because there would be an opposite temperature difference ...
Analyzing various SBLOCA with high pressure safety injection (HPSI) at VVER-440/213, we met a surprising phenomenon - a 'natural' circulation post SG heat transfer reversal. This is not usual, because normal natural circulation (NC) in primary circuit is connected with positive heat transfer at SG. If there is reverse heat transfer at SG (as soon as the break enthalpy outflow is sufficient for removal of reactor decay heat), it should obstruct any natural circulation. The question was, what is the driving force of this 'non-standard natural circulation'. After all we revealed that force - it is the density difference between the colder water in reactor downcomer (cold water from HPSI) and warmer water in inner reactor (lower plenum, core, upper plenum). This phenomenon could be confusing for operating personal, because there would be an opposite temperature difference at the loop than by normal ...
Gas storage is a critical element in the natural gas industry. Producers, transmission and distribution companies, marketers, and end users all benefit directly from the load balancing function of storage. The unbundling process has fundamentally changed the way storage is used and valued. As an unbundled service, the value of storage is being recovered at rates that reflect its value. Moreover, the marketplace has differentiated between various types of storage services and has increasingly rewarded flexibility, safety, and reliability. The size of the natural gas market has increased and is projected to continue to increase towards 30 trillion cubic feet over the next 10 to 15 years. Much of this increase is projected to come from electric generation, particularly peaking units. Gas storage, particularly the flexible services that are most suited to electric loads, is crucial in meeting the needs of these new markets. To ...
The purpose of the project is to further develop a Danish natural gas reformer system including optimisation of subsystems and the overall system consisting of a natural gas reformer and fuel cell CHP generator. This will contribute to the evaluation of to what extend Denmark shall develop small reformer units for PEM fuel Cells. In the project a reformer system with a high degree of automatic control has been build that fulfils the CHP requirements to operation time, dynamics etc. This work, with a FP05 reformer unit, has given valuable results concerning the possibilities and limitations of the reformer technology for CHP usage. It is important that the reformer and fuel cell units are designed with matching yields to optimise efficiency, turn-down start-up time etc. The burner that delivers heat for the steam reaction shall be able to use natural gas as fuel. This gives the possibility of using ...
There is a crescent interest in the scientific community in the study of natural circulation phenomenon. New generation of compact nuclear reactors uses the natural circulation of the fluid as a system of cooling and of residual heat removal in case of accident or shutdown. The objective of this paper is to present a study through the comparison of experimental data and numerical simulation for the natural circulation phenomenon in one and two-phase flow regime. An experimental circuit built with glass tubes is used for the experiments. Thus, it allows the thermal hydraulic phenomena visualization. There is an electric heater as the heat source, a heat exchanger as the heat sink and an expansion tank to accommodate fluid density excursions. The circuit instrumentation consists of thermocouples and pressure meters to better keep track of the flow and heat transfer phenomena. Instrumentation data ...
ObjectivesTo extend a set of work carried out previously at Royal Holloway, the Natural History Museum and elsewhere, and instigated, to a considerable extent, by the PI to determine~%~~%~1. whether there is any significant difference in the performance of clay minerals in the presence of leachates generated by wastes from different cultures and/or deposited in different climates;~%~~%~2. what causes some, if not all, clay minerals to aggregate after reaction with landfill Ieachate;~%~~%~3. the permeabili [continued...]DescriptionAround 1995 it was shown that that interactions between clay minerals and landfill leachate destroy the clay mineral lattice, leading to reduced liner permeability. Recent work indicates that the effect may be caused by dissolution of silica and deposition of amorphous alumina. Most work to date has been done using synthetic and natural ...
The Large Hadron Collider presents an unprecedented opportunity to probe the realm of new physics in the TeV region and shed light on some of the core unresolved issues of particle physics. These include the nature of electroweak symmetry breaking, the origin of mass, the possible constituent of cold dark matter, new sources of CP violation needed to explain the baryon excess in the universe, the possible existence of extra gauge groups and extra matter, and importantly the path Nature chooses to resolve the hierarchy problem - is it supersymmetry or extra dimensions. Many models of new physics beyond the standard model contain a hidden sector which can be probed at the LHC. Additionally, the LHC will be a top factory and accurate measurements of the properties of the top and its rare decays will provide a window to new physics. Further, the LHC could shed light on the origin of neutralino masses if the new physics associated with their ...
Acid Rock Drainage (ARD) is the product formed by the atmospheric oxidation of the relatively common pyrite and pyrrhotite. Waste rock dumps and tailings containing sulfide mineral have been reported at toxic materials producing ARD. Mining in sulphide bearing rock is one of activity which may lead to generation and release of ARD. ARD has had some major detrimental affects on mining areas. The purpose of this study was carried out to develop disposal method for preventing contamination of water and soil environment by waste rocks dump and tailings, which could discharge the acid drainage with high level of metals. Scope of this study was as following: environmental impacts by mine wastes, geochemical characteristics such as metal speciation, acid potential and paste pH of mine wastes, interpretation of occurrence of ARD underneath tailings impoundment, analysis of slope stability of tailings dam etc. The following procedures were used as part of ARD evaluation and ...
The studies of forced jet augmentation of natural convection heat transfer are introduced. It investigates experimentally mixed convection and heat transfer augmentation by forced jets in a large rectangular enclosure with a vertical cooling surface. The experiment is designed to measure the key parameters governing the heat transfer augmentation by a forced jet, and to investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio, on conditions simulating those of actual passive containment cooling systems and scales approaching those of actual containment buildings or compartments. The tests that cover a variety of injection modes will contribute to reveal the nature of mixing and stratification phenomena under accident conditions to a new generation of inherently safe reactors. With similarity considerations on governing equations, the ...
Following the publication (Stenhouse and Baxter, Nature; 267:828 (1977)) of the levels of bomb "1"4C and the residence times of carbon in the human body, excess radiation burdens from this radioisotope are evaluated under the assumption that no radiation dose, however small, can be regarded as entirely harmless biologically. The estimated annual absorbed dose attributable to "1"4C both natural and man-made for 1953-1973 and similar predicted figures for 1975-2025 are shown graphically. The cumulated doses to gonads (over 30 yr) and to bone marrow and bone-lining cells (over 60 yr) and also estimates of the biological damage to reproductive cells from "1"4C #beta#-irradiation (30 yr accumulated dose) are presented. It is concluded from both genetic and somatic considerations, that the potential human radiation burden due to artificially produced "1"4C calculated using the assumptions stated is certainly significant and, therefore, cannot be ...
Macroinvertebrate communities in Rietvlei nature reserve wetland area and their relationship with water quality were studied with the aim to evaluate their use as potential indicators of pollution. Sampling locations were selected to include outlets from swage effluent, agricultural and informal residential runoff. A large increase in nutrient concentrations was observed downstream from discharged treated sewage with an associated decrease in species richness. Bioassays performed included: Daphnia magna, Hydra attenuate, Lactuca sativa, Allium cepa and Pyxicephalus adspersus. The highest percentage of lethality response to a screen (100% concentration) of sampled wetland water by test specimens were observed at the point source input of the Hartbeespoort treated sewage plant. Data generated from the AUSRIVAS method and multitrophic level bioassays revealed the deterioration of the wetland possibly due to factors such as increasing urbanization, ...
In the Peruvian natural forest there are several kind of woods, some of those are not of commercial interest, because have not resistance at termites and wet, are too soft, or can not be well finished, in the others. The present work is devoted to improvement of the physical properties of wood, such as hardness, traction, wet resistance, etc., by means of the generation of a composite wood-polymers cured by using gamma irradiation. The main objective is to establish the main parameters for the polymerization process (economic technical aspect) that decrease the amount of water absorption, in consequence the volumetric variation of Catahua, Mohena and Capirona woods. Gamma irradiation also provides good protection against the biological agents. In consequence, these woods increase its intrinsic and economic values. (author)
This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This report provides the early data results and implementation experience of the AT fuel cell bus since it was placed in service.
Testbed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited, Switzerland and its Japanese licensees Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), Nippon Kokan KK (NKK) and Sumitomo Heavy Industries Ltd. (SHI). Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited or for the generation of electricity in stationary plants, the RTA dual-fuel engine is an economic and reliable alternative to the steam or gas turbines.
This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1992. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Two other projects are underway with the objective of developing (1) a membrane-assisted solvent extraction method for treating natural and process waters contaminated by volatile organic compounds and (2) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process.
The X-ray storage phosphor CsBr:Eu2+ in form of needle image plates is believed to be a promising alternative to the granular BaFBr:Eu2+ with regard to PSL yield and spatial resolution. Unfortunately, CsBr:Eu2+ exhibits poor radiation hardness, which is caused by a migration of europium ions initiated by naturally existing defect centers like (Eu2+-VCs)-centers and X-ray generated MEu-centers. It will be shown that the formation of (Eu2+-O2?)-dipoles at the expense of (Eu2+-VCs)-dipoles, incorporated by thermal annealing in O2-containing and humid atmosphere, does not improve the radiation stability. There is, however, a strong improvement in the radiation hardness by codoping of CsBr:Eu2+ with lithium ions, which is accompanied by a complete suppression of the previously observed MEu-cent...
We study CP-violating phenomena in the production, mixing and decay of a coupled system of CP-violating neutral Higgs bosons at {gamma}{gamma} colliders, assuming a Minimal Supersymmetric Standard Model (MSSM) Higgs sector in which CP violation is radiatively induced by phases in the soft supersymmetry-breaking gaugino masses and third-generation trilinear squark couplings. We discuss CP asymmetries in the production and decays of {mu}{sup +}{mu}{sup -}, {tau}{sup +}{tau}{sup -}, b-bar b and t-bar t pairs. We find large asymmetries when two (or all three) neutral Higgs bosons are nearly degenerate with mass differences comparable to their decay widths, as happens naturally in the CP-violating MSSM for values of tan{beta}-bar 5 (30) and large (small) charged Higgs-boson masses.
We study CP-violating phenomena in the production, mixing and decay of a coupled system of CP-violating neutral Higgs bosons at #gamma##gamma# colliders, assuming a Minimal Supersymmetric Standard Model (MSSM) Higgs sector in which CP violation is radiatively induced by phases in the soft supersymmetry-breaking gaugino masses and third-generation trilinear squark couplings. We discuss CP asymmetries in the production and decays of #mu#"+#mu#"-, #tau#"+#tau#"-, b-bar b and t-bar t pairs. We find large asymmetries when two (or all three) neutral Higgs bosons are nearly degenerate with mass differences comparable to their decay widths, as happens naturally in the CP-violating MSSM for values of tan#beta#-bar 5 (30) and large (small) charged Higgs-boson masses.
Test bed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine-type, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited and its Japanese licenses. Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited for the generation of electricity in stationary plants, the RTA dual-fuel engines is an economic and reliable alternative to the steam or gas turbine. The performance of the engine is discussed.
A cold-leg small-break loss-of-coolant accident (SBLOCA) experiment was performed on the PACTEL facility to study the behavior of natural circulation in a VVER-440 reactor geometry. The facility is a volumetrically scaled (1:305) integral test loop simulating the VVER-440 reactors used in Finland. The test results were used to assess the computer codes RELAP5/MOD3.1 and APROS 3.0 for VVER reactors. The behavior of the horizontal steam generator and the effect of the hot-leg loop seal were of particular interest. The specific parameters to be compared included the primary pressure and the downcomer mass flow rate.
A cold-leg small-break loss-of-coolant accident (SBLOCA) experiment was performed on the PACTEL facility to study the behavior of natural circulation in a VVER-440 reactor geometry. The facility is a volumetrically scaled (1:305) integral test loop simulating the VVER-440 reactors used in Finland. The test results were used to assess the computer codes RELAP5/MOD3.1 and APROS 3.0 for VVER reactors. The behavior of the horizontal steam generator and the effect of the hot-leg loop seal were of particular interest. The specific parameters to be compared included the primary pressure and the downcomer mass flow rate.
This paper investigates the phase change behavior of 65 mol% capric acid and 35 mol% lauric acid, calcium chloride hexahydrate, n-octadecane, n-hexadecane, and n-eicosane inside spherical enclosures to identify a suitable heat storage material. Analytical models are developed for solidification and melting of sphere with conduction, natural convection, and heat generation. Both the models are validated with previous experimental studies. Good agreement was found between the analytical predictions and experimental study and the deviations were lesser than 20%. Heat flux release at the wall, cumulative energy release to the external fluid, are revealed for the best PCM. The influence of the size of encapsulation, initial temperature of the PCM, the external fluid temperature on solidified and molten mass fraction, and the total phase change time are also investigated. (author)
Details of a 1 day conference designed to create more efficient interactions between the gas supply and electricity systems in Ontario and new models for gas supply and the electricity system were presented. Market efficiency, generators' perspectives on critical gas issues, an overview of the North American gas and an outline of issues concerning Ontario were discussed. A natural gas industry forecast and issues concerning marketers and producers were presented. The terms on which gas is bought and sold were discussed. Regulatory tools, cost allocation and issues relating to unbundling were also presented. Infrastructure needs were reviewed, as well as basic market structures. It was suggested that appropriate commercial service options need to be developed and approved, including cross-utility services.
An algorithm for creating synthetic telescope images of Smoothed Particle Hydrodynamics (SPH) density fields is presented, which utilises the adaptive nature of the SPH formalism in full. The imaging process uses Monte Carlo Radiative Transfer (MCRT) methods to model the scattering and absorption of photon packets in the density field, which then exit the system and are captured on a pixelated image plane, creating a 2D image (or a 3D datacube, if the photons are also binned by their wavelength). The algorithm is implemented on the density field directly: no gridding of the field is required, allowing the density field to be described to an identical level of accuracy as the simulations that generated it. Some applications of the method to star and planet formation simulations are presented to illustrate the advantages of this new technique, and suggestions as to how this framework could support a Radiative Equilibrium algorithm are also given ...
Methodology, characteristics, features and results obtained for greenhouse gases within the recent Swiss LCA study 'Environmental Life-Cycle Inventories of Energy Systems' are presented. The focus of the study is on existing average Full Energy Chains (FENCHs) in the electricity generation mixes in Europe and in Switzerland. The systems, including coal (hard coal and lignite), oil, natural gas, nuclear and hydro, are discussed one by one as well as part of the electricity mixes. Photovoltaic systems are covered separately since they are not included in the electricity mixes. A sensitivity analysis on methane leakage during long-range transport via pipeline is shown. Whilst within the current study emissions are not attributed to specific countries, the main sectors contributing to the total GHGs emissions calculated for the various FENCHs are specified. (author). 10 refs, 10 figs, 9 tabs.
Permian coal and Triassic mudstone from the Ordos Basin were pyrolyzed in a closed system using a gold tube technique. Carbon and hydrogen isotopes of the gases generated from pyrolysis were compared to Mesozoic gases in the basin to interpret the origin, maturity and any mixing of gases. Maturation trends for thermogenic methane from both coal and lacustrine kerogens in our experiment were found to be independent of heating rate, allowing their use for determination of gas provenance. Gases from a tectonically stable area like the Shanbei slope are derived mainly from Yanchang lacustrine kerogen, and gases in tectonically active areas consist of mixtures of coal-derived gases and oil-associated methane from deeply buried formations, as well as oil-associated gases and biogenic gases from ...
This article reports on the world's first gas turbine to top 40% thermal efficiency in simple cycle and is now operating commercially as part of a natural-gas-fired combined-cycle cogeneration (CC) plant serving the Ottawa Health Sciences Center, Ottawa, Ont, Canada. Owned and operated by TransAlta Energy Corp, Calgary, Alta, the CC plant supplies steam and hot and chilled water to the health center and another thermal user while the electricity is sold to Ontario Hydro. Part of the project included the conversion of 15-psig steam-carrying equipment to hot-water service. Commercial success of this installation heralds a new era in the application of efficient gas turbines for power generation.
GPM moves from the clean room to the test chamber on a dolly without wheels. Compressed air is pumped out under airpads that float the Spacecraft on a bed of air. nThe wind generated when the centrifuge moves at its maximum speed are more than 200 mph - that's tornado speed. But since they move with the centrifuge the satellites tested only feel 20 mph winds. nLeaning outward at 45 degrees for one test orientation, GPM comes within 28 inches of the wall. When lifted onto the platform it cleared the ceiling by only five inches. nNatural audio only. nVideo Credit: Brooke Harris n
Abstract To investigate the link between the functionality and the diversity of microbial communities under strong selective pressure from pollutants, two types of mesocosms that simulate natural attenuation and phytoremediation were generated using soil from a site highly contaminated with jet fuel and under air-sparging treatment. An increase in the petroleum hydrocarbon concentration from 4900 to 18-500-mg-kg-1-dw soil simulated a pollutant rebound (postremediation pollutant reversal due to residual contamination). Analysis of soil bacterial communities by denaturing gradient gel electrophoresis of PCR-amplified 16S rRNA gene fragments showed stronger changes and selection for a phylogenetically diverse microbial population in the mesocosms with pollutant-tolerant willow trees. Enumerat...
Data from Monte Carlo transport codes are used to model radiobiological effects. We previously reported the Fourier analysis of ionization data generated by simulating a 500-keV proton traversing water. Here, we extend Fourier analysis to energy transfer data of another radiation type, a 14-MeV #alpha#-particle. A radiobiological model based on this frequency-domain analysis views cell as an information processing system . It lends itself naturally to traditional engineering analyses. One engineering principle-the output response of a linear system to random signal-is applied here to explain the fact that there is measurable difference in the magnitude of the biological effectiveness when a given biological system is irradiated with two different radiation types of the same Linear Energy Transfer (LET).
Studies relative to some formation evaluation aspects of geothermal reservoirs are reported. The particular reservoirs considered were the liquid dominated type with a lithology of the sedimentary nature. Specific problems of interest included the resistivity behavior of brines and rocks at elevated temperatures and studies on the feasibility of using the well log resistivity data to obtain estimates of reservoir permeability. Several papers summarizing the results of these studies were presented at various technical meetings for rapid dissemination of the results to potential users. These papers together with a summary of data most recently generated are included. A brief review of the research findings precedes the technical papers. Separate abstracts were prepared for four papers. Five papers were abstracted previously for EDB.
Recently several investigators reported on various means of generating cold plasma jets at atmospheric pressure. More interestingly, these jets turned out to be not continuous plasmas but trains of small high velocity plasma packets/bullets. However, until now little is known of the nature of these 'bullets'. Here we present experimental insights into the physical and chemical characteristics of bullets. We show that their time of initiation, their velocity and the distance they travel are directly dependent on the value of the applied voltage. We also show that these bullets can be controlled by the application of an external electric field. Using an intensified charge coupled device camera we report on their geometrical shape, which was revealed to be 'donut' shaped, therefore giving an indication that solitary surface ionization waves may be responsible for the creation of these bullets. In addition, using emission spectroscopy, we follow ...
The excitation functions of the reactions "9"8Mo(d,p)"9"9Mo and "1"0"0Mo(d,p)"1"0"1Mo have been determined by irradiation of stacked foils with deuterons of energies less than 13 MeV and non-destructive determination of the absolute activity of the Mo radioisotopes by semiconductor #gamma#-ray spectrometry. From the excitation functions, the thick-target yields and the saturation production rates of "9"9Mo and "1"0"1Mo for deuteron energies of 13.0 MeV and 11.7 MeV have been calculated. Implications for the production of "9"9Mo for generators of sup(99m)Tc are discussed. (author).
Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific.
Hydrous pyrolysis of immature Monterey Phosphatic or Siliceous rock at progressively higher temperatures causes systematic changes in biomarker thermal maturity parameters of the generated hydrocarbons. Biomarker ratios based on proposed carbon-carbon cracking or aromatization reactions increase during hydrous pyrolysis along similar pathways for both Siliceous and Phosphatic members. An increase in these biomarker ratios is also observed for oils of increasing thermal maturity from the offshore Santa Maria Basin, although the rates of changes for each parameter differ between the hydrous pyrolysis and natural samples. Changes in some cracking parameters during maturation appear to result from differential thermal stability of the compounds rather than conversion of precursors to products. (author).
The purpose of this study is to search for a new method of dispersing spilled heavy oil, which has a detrimental effect on the natural environment and marine ecosystem. A method ejecting a waterjet vertically downward to heavy oil on the water surface was studied, particularly focusing on the effect of the guide nozzle shape. The waterjet comprised heavy oil and minute air bubbles, and passed through the hole of the guide nozzle. Thirteen guide nozzle shapes were tested and compared. The dispersion efficiency of a tapered hole was the best among the 13 nozzles. The flow in the hole of the guide nozzles was recorded by a high-speed video camera. The occurrence of two flows, regular and counter flows, was observed in the taper guide nozzle. It seemed that the counter flows generated the shearing force between the waterjet and the heavy oil layer. It is considered that the shearing force determines the surplus efficiency of disperse.
A drift dye tracer experiment, using Rhodamine (WT) dye, was conducted on airborne drift from a natural draft cooling tower at PEPCO's Chalk Point, Maryland Power Generating Station. This experiment was designed to separate and identify cooling tower aerosol deposition from other sources and to provide a data base for use in cooling tower salt loading and model validation. Prior to the experiment, laboratory tests showed that Rhodamine (WT) was inexpensive, safe and controllable when used as a drift dye tracer. Positive identification and separation of cooling tower drift can be made among other sources using a dye tracer.
Baobab fruit are harvested and used throughout Africa as an important source of food and are sold to generate income. Commercial use is increasing rapidly as derivatives of the fruit such as baobab seed oil and fruit pulp are being exported to Europe and North America. The cash derived from the sale of fruit support thousands of rural people. This study examines baobab fruit yields in an area being harvested for commercial use. It represents baobab populations and harvesting scenarios typically found in Southern Africa and is the first study in Africa to combine demographic and production data in determining baobab fruit yields. Fruit production was examined across five land-use types (nature reserves, rocky outcrops, plains, fields and villages) and over three consecutive years. Factors a...
We consider 4-dimensional space-times which are asymptotically flat at spatial infinity and show that, in the first order framework, action principle is well-defined \\emph{without the need of infinite counter terms.} It naturally leads to a covariant phase space in which the Hamiltonians generating asymptotic symmetries provide the total energy-momentum and angular momentum of the space-time. We address the subtle but important problems that arise because of logarithmic translations and super-translations both in the Langrangian and Hamiltonian frameworks. As a forthcoming paper will show, the treatment of higher dimensions is considerably simpler. Our first order framework also suggests a new direction for generalizing the spectral action of non-commutative geometry.
The problems are discussed of using radionuclide X-ray fluorescence analysis (the most frequently used source is "2"4"1Am) and neutron activation analysis for monitoring the chemical quality of the working environment of a welder. Elements determinable by these methods are listed and the advantages of the methods stated with regard to speed, simplicity and appropriate accuracy of measurement together with commercial availability of the instruments. Welding as a source of harmful substances is assessed by determination of the amount of chromium in aerosols generated by welding austenitic chromium-nickel steels. The described methods allow to obtain a complex image of the chemical nature of welding aerosols and to understand the mechanism of their impact on the human organism. (J.C.).
Effects of some experimental parameters (supporting electrolyte, initial pH and current density) on the performance of electrocoagulation process using iron electrodes were investigated. Results of experiments showed that dissolution of iron is purely electrochemical and fits well with Faraday's law and leads to Fe^2^+ which are chemically oxidized into Fe^3^+ in aerated conditions. In neutral and alkaline conditions, the reaction between hydroxyl ions generated at the cathode and dissolved iron ions forms insoluble hydroxo-iron species. Potentiodynamic polarization tests showed that the formation of passive film on iron anode limits the continuous electrochemical dissolution of iron. Corrosion and pitting potentials largely depend on the nature of supporting electrolyte. The dissolution o...
A growing number of applications that generate massive streams of data need intelligent data processing and online analysis. Real-time surveillance systems, telecommunication systems, sensor networks and other dynamic environments are such examples. The imminent need for turning such data into useful information and knowledge augments the development of systems, algorithms and frameworks that address streaming challenges. The storage, querying and mining of such data sets are highly computationally challenging tasks. Mining data streams is concerned with extracting knowledge structures represented in models and patterns in non stopping streams of information. Generally, two main challenges are designing fast mining methods for data streams and need to promptly detect changing concepts and data distribution because of highly dynamic nature of data streams. The goal of this article is to analyze and classify the application of diverse data mining ...
A substantial global market for advanced power systems is expected to develop early in the next century for both repowering and new capacity additions, Although natural gas-fueled systems, such as gas turbines, are expected to dominate in the 1990`s, coal-fueled systems are expected to emerge in the 2000`s as systems of choice for base-load capacity because of coal`s lower expected cost. Stringent environmental regulations dictate that all advanced power systems must be clean, economical, and efficient in order to meet both the environmental and economic performance criteria of the future. Recognizing these needs, the DOE strategy is to carry out an effective RD&D program, in partnership with the private sector, to demonstrate these technologies for commercial applications in the next century. These technologies are expected to capture a large portion of the future power generation market. The DOE: expects that, domestically, advanced power ...
We discuss a differential integrable hierarchy, which we call the (N, M)-th KdV hierarchy, whose Lax operator is obtained by properly adding M pseudo-differential terms to the Lax operator of the N-th KdV hierarchy. This new hierarchy contains both the higher KdV hierarchy and multi-field representation of KP hierarchy as sub-systems and naturally appears in multi-matrix models. The (N+2M-1) coordinates or fields of this hierarchy satisfy two algebras of compatible Poisson brackets which are local and polynomial. Each Poisson structure generate an extended W_1_+_#infinity# and W_#infinity# algebra, respectively. We call W (N, M) the generating algebra of the extended W_#infinity# algebra. This algebra, which corresponds with the second Poisson structure, shares many features of the usual W_N algebra. We show that there exist M distinct reductions of the (N, M)-th KdV hierarchy, which are obtained by imposing suitable second ...
Use of gas-fired combined-cycle technology (GFCC) in the electric-utility sector could play an important role in a least-cost planning strategy and thereby provide significant benefits to the utilities and their customers. Potential benefits include reduced capital and operating costs, more-effective matching of load growth and capacity additions, greater system reliability, and reduced environmental emissions. GFCC technology was examined in eight utility systems in six geographic regions to estimate the potential benefits of its use. In all systems, GFCC technology was shown to have the potential to reduce the cumulative capital costs for adding new capacity. The overall conclusion of the study is that GFCC technology offers the potential for significant savings in many regions of the United States and that these benefits would appear over a wide range of economic conditions. The study provides insight into the important technological and economic factors influencing the ...
The following industrial-scale power station processes are compared with natural gas/light fuel oil heating: Conventional steam generation, steam generation with gas turbine upstream, gas turbine process with low-pressure-waste heat boiler and cogeneration. Industrial gas turbines between 10 and 25 MW are compared with one another; typical boilers and industrial turbines are described. CO{sub 2} and NO{sub x} emissions are indicated. The steam turbines used are the efficient and robust turbines used in industry, wherever possible they are built as single-line plant with the gas turbine. (orig.) [Deutsch] Es werden folgende Industriekraftwerksprozesse mit Erdgas-Leichtoelfeuerung verglichen: Konventioneller Dampfprozess, Dampfprozess mit Vorschaltgasturbine, Gasturbinenprozess mit ND-Abhitzekessel und Kombianlage. Die Industriegasturbinen zwischen 10 und 25 MW werden gegenuebergestellt und typische Kessel und ...
This work aims at improving the understanding of the dynamics of a Free Electron Laser (FEL) based on a storage ring. A new phenomenon of saturation by the electron bunch transverse dimensions is pointed out, during the FEL operation with a magnetic optics ''low emittance''. A part of this thesis work concerns the study of the longitudinal dynamics of the FEL depending on a parameter: the detuning between the pass frequency of the electrons and the back and return frequency of the laser pulse in the optical cavity. This study shows that the FEL presents a pulsed or a steady state behavior depending on the detuning. Besides, a spectro-temporal behavior of the FEL is pointed out showing the FEL pulse substructures and holes in the spectrum. Another part of this work concerns the response of the resonant FEL system, when a perturbation is applied on the gain. Under the effect of a modulation, the FEL can present a periodic or chaotic regime. The analysis of these regimes shows that a ...
Chlorine is widely used in drinking water disinfection due to be a powerful and not expense disinfection. Although the benefits of disinfection, the formation of stable disinfection by-products of the health concern, is the result of the interaction of aqueous chlorine with natural organic matter presents in water. Disinfection by-products generated in major concentration are trihalomethane and haloacetic acids. Disinfection by-products generated in minor concentration are haloacetonitriles, haloketones,chloral hydrate and chloropicrin and some new groups such as cyanogen halides and trihaloacetaldydes. In this work two analytical methods.: headspace/gas chromatography/electron capture detector and liquid-liquid microextraction/gas chromatography/electron capture detector are studied and compared to determine the minor by-products and to establish finally, a systematic control of them in the different stages of the Water ...
The DOE Working Group for an Assessment of Coal-Gasification Research Needs (COGARN - coal gasification advanced research needs) has reviewed and evaluated US programs dealing with coal gasification for a variety of applications. Cost evaluations and environmental-impact assessments formed important components of the deliberations. We have examined in some depth each of the following technologies: coal gasification for electricity generation in combined-cycle systems, coal gasification for the production of synthetic natural gas, coal gasifiers for direct electricity generation in fuel cells, and coal gasification for the production of synthesis gas as a first step in the manufacture of a wide variety of chemicals and fuels. Both catalytic and non-catalytic conversion processes were considered. In addition, we have constructed an orderly, long-range research agenda on coal science, pyrolysis, and partial combustion in order ...
The overall goal of the Gas-to-Liquids Program at the U.S. Department of Energy`s Pittsburgh Energy Technology Center (PETC) is to develop technologies for the production of hydrocarbon fuels and premium chemicals from light alkane gases. PETC`s current Gas-to-Liquids Program comprises the development of four primary advanced conversion technologies, namely, partial oxidation, oxidative coupling, oxyhydrochlorination, and novel conversion processes. Based on the current state of development, it can be concluded that, in the near future, one or more of these technologies will reach proof-of-concept demonstration. Oxyhydrochlorination is the most advanced direct conversion technology, and the synthesis of lower cost methyl chloride from natural gas would impact several commercial technologies that utilize methyl chloride as an intermediate to high value products. Technology development for the partial oxidation of methane to synthesis gas using ceramic membranes ...
This paper describes the modeling of horizontal steam generator with the TRACE code and calculation results of a loss-of-feedwater (LOF-10) experiment at the PACTEL facility. Parallel Channel Test Loop (PACTEL) is an integral test facility for a VVER-440 type nuclear reactor. The main objectives were to prepare a simulation model for its horizontal steam generator with the TRACE thermal hydraulic code and assess different modeling options of the code. PACTEL experiment LOF-10 was chosen for this assessment. The calculation results showed that TRACE is capable in simulating horizontal steam generator behavior both in steady state and during loss-of-feedwater transient. The phenomenon of heat transfer from primary to secondary side, steam superheating and flow reversal in the lowest heat exchange tubes were studied in detail. Different nodalization options were introduced. In the simulation of PACTEL loss-of-feedwater ...
This paper describes the modeling of horizontal steam generator with the TRACE code and calculation results of a loss-of-feedwater (LOF-10) experiment at the PACTEL facility. Parallel Channel Test Loop (PACTEL) is an integral test facility for a VVER-440 type nuclear reactor. The main objectives were to prepare a simulation model for its horizontal steam generator with the TRACE thermal hydraulic code and assess different modeling options of the code. PACTEL experiment LOF-10 was chosen for this assessment. The calculation results showed that TRACE is capable in simulating horizontal steam generator behavior both in steady state and during loss-of-feedwater transient. The phenomenon of heat transfer from primary to secondary side, steam superheating and flow reversal in the lowest heat exchange tubes were studied in detail. Different nodalization options were introduced. In the simulation of PACTEL loss-of-feedwater ...
Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam- cycle is the conventional conversion method; however, total energy conversion efficiencies for this type of process are only slightly over 30{percent}. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40{percent}. Conversion processes based on gasification offer efficiencies above 50{percent}. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. Problems arise due to the corrosive nature of H{sub 2}S on metal components contained in these cycles. Because of this, H{sub 2}S concentrations must be reduced to low levels corresponding to certain power applications. An advanced process for the separation of hydrogen sulfide (H{sub 2}S) from coal gasification product ...
The book tries about the International and national aspects, natural gas situation, production, consumption, prices, demand projection, energetic plans, norms and laws of the natural gas in Colombia
This document provides information on the supply and disposition of natural gas to a wide audience. The 1996 data are presented in a sequence that follows natural gas from it`s production to it`s end use.
This presentation outlined the energy policy in the United States and its impact on frontier development in Alaska, deepwater offshore fields and in the western oil shale resources. The energy strategy focuses on technologies that increase domestic production from existing resources as well as technologies that create new sources of energy. In addition to emphasizing the cooperation between Canada and the United States in ensuring energy supply security and stability, this paper discussed the importance of overall bilateral trade between the 2 countries. It was noted that Canada is the United State's most secure and reliable energy partner and is the number 1 supplier of imported oil, natural gas, electricity and uranium. The Bush administration's energy policy is based on the mandate to supply stable, reliable, secure, affordable and environmentally sound energy for the country's growing economy. The energy strategy focuses on increasing ...
This report presents the work performed at the Institute of Gas Technology (IGT) during the second program quarter from October 1, 1993 to December 31, 1993, under Department of Energy (DOE) Contract No. DE-AC22-93PC92114. This program has co-ordinated funding for Task 1 from IGT`s Sustaining Membership Program (SMP), while DOE is funding Tasks 2--8. Progress in all tasks are reported. The overall objective of this research project is to develop a catalytic process to convert natural gas to liquid transportation fuels. The process consists of two steps that each utilize catalysts and sulfur containing intermediates: (1) to convert natural gas to CS{sub 2} and (2) to convert CS{sub 2} to gasoline range liquids. Experimental data will be generated to demonstrate the potential of catalysts and the overall process. During this quarter, progress in the following areas has been made. An existing unit at IGT was modified to ...
The combustion/emissions control island of the CFTCC plant produces cleaned coal combustion gases for expansion in the gas turbine. The gases are cleaned to protect the turbine from flow-path degeneration due to coal contaminants and to reduce environmental emissions to comparable or lower levels than alternate clean coal power plant tedmologies. An advantage of the CFTCC system over other clean coal technologies using gas turbines results from the CFTCC system having been designed as an adaptation to coal of a natural gas-fired combined cycle plant. Gas turbines are built for compactness and simplicity. The RQL combustor is designed using gas turbine combustion technology rather than process plant reactor technology used in other pressurized coal systems. The result is simpler and more compact combustion equipment than for alternate technologies. The natural effect is lower cost and improved reliability. In addition to new power ...
... Question Chronic fatigue: Can natural remedies boost my energy? Are there any natural remedies that reduce chronic ... AN01764 ">Chronic fatigue: Can natural remedies boost my energy? Guidelines for sites linking to MayoClinic.com ...
The objectives of this program are to evaluate the Coal Fired Combined Cycle (CFCC) power plant conceptual design and to conduct supporting development programs for pressurized fluidized bed technology advancement in combustion/steam generator, gas turbine and hot gas cleanup technologies. The Coal-Fired Combined Cycle is the unique power plant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined-cycle power plant. The advantages of the combined cycle for higher efficiency and the potential of the pressurized fluidized bed combustor improvements in emissions could offer a new and attractive option to the electric utility industry. The CFCC approach provides for cooling the fluid bed combustor through the use of steam tubes in the bed which supply a steam turbine generator. The partially cooled combustion gases drive a gas turbine ...
This paper describes the methods and systems as utilized in an integrated experimental thermohydraulic/mechanics analysis test program on waterhammer pressure pulses within a revised feedwater sparger of a Loviisa generation VVER-440-type reactor. This program was carried out in two stages: (1) measurements with a strictly limited set of operating parameters at Loviisa NPP, and (2) measurements with the full set of operating parameters on a test article simulating the revised feedwater sparger. The experiments at Loviisa NPS served as an invaluable source of information on the nature of waterhammer pressure pulses and structural responses. These tests thus helped to set the objectives and formulate the concept for series of tests on a test article to study the water hammer phenomena. The heavily instrumented full size test article of a steam generator feedwater sparger was placed within a pressure vessel simulating the ...
A 1,200-W solar AMTEC (alkali metal thermal-to-electric conversion) power system concept was developed and integrated with an advanced global positioning system (GPS) satellite. The critical integration issues for the SAMTEC with the GPS subsystems included (1) packaging within the Delta 2 launch vehicle envelope, (2) deployment and start-up operations for the SAMTEC, (3) SAMTEC operation during all mission phases, (4) satellite field of view restrictions with satellite operations, and (5) effect of the SAMTEC requirements on other satellite subsystems. The SAMTEC power system was compared with a conventional planar solar array/battery power system to assess the differences in system weight, size, and operations. Features of the design include the use of an advanced multitube, vapor anode AMTEC cell design with 24% conversion efficiency, and a direct solar insolation receiver design with integral LiF salt canisters for energy storage to generate power during the ...
Inverter introduced in this paper is intended for use in medium-capacity photovoltaic power generation systems designed for industries in general. Interconnection is carried out at a low-voltage 210V point receiving from a commercial 3 phase-3 cable 6.6kV high voltage incoming panel. So as to ensure stable extraction of power in the maximum degree from a photovoltaic power generation system that is naturally unstable, this inverter monitors voltage and power, and behaves in a fully automated way. A maximum power point tracking (MPPT) control function is provided, which measures the power level at the current operating voltage point A, changes the operating voltage to a voltage value B which is lower than the point A voltage by 3V and to a voltage value C which is higher than the point A voltage by 3V, and measures the power level at each point. Comparison is then made between the values measured at the said points on a PV ...
Magnetic fields correlated on several kiloparsec scales are seen in spiral galaxies. Their origin could be due to the winding up of a primordial cosmological field or due to amplification of a small seed field by a turbulent galactic dynamo. Both options have difficulties: There is no known battery mechanism for producing the required primordial field. Equally the turbulent dynamo may self destruct before being able to produce the large scale field, due to excess generation of small scale power. The current status of these difficulties is discussed. The resolution could depend on the nature of the saturated field produced by the small scale dynamo. We argue that the small scale fields do not fill most of the volume of the fluid and instead concentrate into intermittent ropes, with their peak value of order equipartition fields, and radii much smaller than their lengths. In this case these fields neither drain significant energy from the ...
We continue our discussion of the general bosonic prototype of the new orbifold-string theories of permutation-type. Supplementing the extended physical-state conditions of the previous paper, we construct here the extended Virasoro generators with cycle central charge $\\hat{c}_j(\\sigma)=26f_j(\\sigma)$, where $f_j(\\sigma)$ is the length of cycle $j$ in twisted sector $\\sigma$. We also find an equivalent, reduced formulation of each physical-state problem at reduced cycle central charge $c_j(\\sigma)=26$. These tools are used to begin the study of the target space-time dimension $\\hat{D}_j(\\sigma)$ of cycle $j$ in sector $\\sigma$, which is naturally defined as the number of zero modes (momenta) of each cycle. The general model-dependent formulae derived here will be used extensively in succeeding papers, but are evaluated in this paper only for the simplest case of the "pure" permutation orbifolds.
Instrumentation research to study the feasibility of using optical data processing techniques to solve real-time pattern recognition problems for high energy physics experiments is now in its second year. During the past year, a prototype optical processor for use in BNL Experiment 702 was conceived and designed, using test data from the experiment and simulating the optical processor in the computer. A number of technical studies have been made, mostly relating to the selection of the optical filter for the processor. Comparisons between natural and synthetic holograms, both bleached and unbleached, have been made. We conclude from these tests that the kinoform, a computer-generated phase hologram, is the optimal choice for this processor. A new method for producing the kinoform has been tried by this group with encouraging results. The optical design for the prototype processor is complete, and the required optical elements, sources, and the ...
Structural and functional responses of a benthic macroinvertebrate assemblage to pulses of the insecticide imidacloprid were assessed in outdoor stream mesocosms. Imidacloprid pulses reduced invertebrate abundance and community diversity in imidacloprid-dosed streams compared to control streams. These results correlated well with effects of imidacloprid on leaf litter decomposition and feeding rates of Pteronarcys comstocki, a stonefly, in artificial streams. Reductions in oxygen consumption of stoneflies exposed to imidacloprid were also observed in laboratory experiments. Our findings suggest that leaf litter degradation and single species responses can be sensitive ecotoxicological endpoints that can be used as early warning indicators and biomonitoring tools for pesticide contamination. The data generated illustrates the value of mesocosm experiments in environmental assessment and how the consideration of functional and structural endpoints of ...
In order to study the boundary conditions for the occurrence of ratcheting, a testing rig was erected. In this rig, small-scale mock-ups of the first wall were tested under mechanical conditions similar to those expected during disruptions. These mock-ups were made of stainless steel AISI 316. They were heated on the surface and water cooled from inside. Disruption forces were simulated by a high-speed hydraulic bending system by impact loads. The mock-ups were heated by a high-frequency generator and cooled by water through two cooling channels.In addition to the experimental work, simplified analytical analysis and numerical calculations were carried out using the finite element program ABAQUS. In these calculations, the temperature and stress fields in the mock-ups were investigated and the influence of the different constitutive equations was studied.The experimental results confirm the ratcheting behaviour predicted by the calculations. It has been ...
Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and engine operating variables are stored in a PC for off line ...
The effect of neutralizing cations on the secondary reactions of the primary products from CO hydrogenation over ion-exchanged zeolite-supported Ru catalysts was investigated using zeolites with different alkali cations (Li/sup +/, Na/sup +/, K/sup +/, Rb/sup +/, Cs/sup +/). The transformation of olefins (propylene and butene) on the zeolites without the metal, under conditions similar to those used for CO hydrogenation, was also studied in order to understand the effect of the various constituents of the support, i.e., the Broensted acid sites generated during catalyst preparation and the alkali cations, on possible secondary reactions of the primary olefinic products. It was established that secondary acid-catalyzed reactions of these primary products can play a major role in shaping product selectivity during CO hydrogenation over zeolite-supported catalysts. Depending on the concentration and the strength of the acid sites, various competitive reaction paths ...
This work, carried out by the parliamentary office for the evaluation of scientific and technological choices on request of the French National Assembly and Senate, takes stock of the present day situation and technical perspectives of development of renewable energy sources and of research needs of the French industry in this domain: 1 - renewable energies: key-technologies for the energy supply of developing countries and for a rational consumption in transportation systems and accommodations of developed countries (energies technically different from fossil or nuclear energies; fundamental energy sources for a developing world; different national goals in Europe depending on the available natural resources and on the political realities; a minor interest in France for the domestic power generation but a major interest for transports, residential and tertiary sectors and export); 2 - priority choices given to the French renewable energy ...
A workshop on radioactivity in coal use was held on September 15 through 17, 1981, under the auspices of the US Department of Energy, Office of Environmental Programs, and the Los Alamos National Laboratory. The purpose of the workshop was to identify research issues associated with radioactivity resulting from the use of coal for electric power generation. The concensus of the 10 scientists participating in the workshop was that a moderate to strong need exists for research in solubility of fly ash in different fluids and for determination of radioactivity in construction materials. Several additional research issues were identified but were given a lower priority. Summaries of each presentation are included. Titles are: some effects of coal combustion on the radiation environment; radionuclides in western coal at Mound; low-level radiation in coals utilized and ashes produced at New York State electric utilities; radioactivity from coal use - where are the ...
This paper presents part-load evaluation of a natural gas-fired chemical looping combustion (CLC) combined cycle with CO2 capture. The novel combined cycle employs an air-based gas turbine, a CO2-turbine and a steam turbine cycle. In this combined cycle, the CLC reactors replace combustion chamber of the gas turbine. The proposed combined cycle has a net plant efficiency of about 52.2% at full-load, including CO2 compression to 200 bar. The part-load evaluation shows that reducing the load down to 60% results in an efficiency drop of 2.6%-points. However, the plant shows better relative part-load efficiency compared to conventional combined cycles. The pressure in CLC-reduction and -oxidation reactors is balanced by airflow control, using a compressor equipped with variable guide vanes. A combination of control strategies is discussed for plant start-up and shutdown and for part-load when airflow reduction is not practically possible with current ...
The traditional way of estimating the gravitational field from observed motions of test objects is based on the virial relation between their kinetic and potential energy. We find a more efficient method. It is based on the natural presumption that the objects are observed at a random moment of time and therefore have random orbital time phases. The proposed estimator, which we call "orbital roulette", checks the randomness of the phases. The method has the following advantages: (1) It estimates accurately Keplerian (point-mass) potentials as well as non-Keplerian potentials where the unknown gravitating mass is distributed in space. (2) It is a complete statistical estimator: it checks a trial potential and accepts it or rules it out with a certain significance level; the best-fit measurement is thus supplemented with error bars at any confidence level. (3) It needs no a priori assumptions about the distribution of orbital parameters of the test bodies. We test ...
Cross-sections for the deuteron-induced reactions on natural molybdenum leading to {sup 93m}Tc, {sup 93m+g}Tc, {sup 94}Tc, {sup 94m}Tc, {sup 95}Tc, {sup 95m}Tc, {sup 96m+g}Tc, {sup 99m}Tc, {sup 99}Mo, {sup 101}Mo, {sup 90m+g}Nb, {sup 92m}Nb, {sup 95}Nb and {sup 89m+g}Zr were measured in the energy range 3.0-19.6 MeV on the cyclotron U-120 M in the Institute of Nuclear Physics AS CR. Special attention was paid to excitation functions and thick target yields for the formation of {sup 95m}Tc, a suitable tracer for {sup 99}Tc, of {sup 96m+g}Tc, which might be used as a beam monitor, and of {sup 99m}Tc and {sup 99}Mo, the most widespread radionuclide generator pair in nuclear medicine. If appropriate, obtained data are compared with the heretofore published cross-sections.
Cross-sections for the deuteron-induced reactions on natural molybdenum leading to "9"3"mTc, "9"3"m"+"gTc, "9"4Tc, "9"4"mTc, "9"5Tc, "9"5"mTc, "9"6"m"+"gTc, "9"9"mTc, "9"9Mo, "1"0"1Mo, "9"0"m"+"gNb, "9"2"mNb, "9"5Nb and "8"9"m"+"gZr were measured in the energy range 3.0-19.6 MeV on the cyclotron U-120 M in the Institute of Nuclear Physics AS CR. Special attention was paid to excitation functions and thick target yields for the formation of "9"5"mTc, a suitable tracer for "9"9Tc, of "9"6"m"+"gTc, which might be used as a beam monitor, and of "9"9"mTc and "9"9Mo, the most widespread radionuclide generator pair in nuclear medicine. If appropriate, obtained data are compared with the heretofore published cross-sections.
A numerical model was developed to simulate the combined effects of heat transfer, magnetite oxidation, and NO{sub x} formation in a grate-kiln furnace for taconite pellet induration. Heat transfer from the flame in the kiln was described by the net radiation method. The shrinking core model was used to account for magnetite oxidation on the grate. A novel approach to oxidation of tumbling pellets in a kiln was derived. The Zeldovich mechanism was used to predict thermal NO generation. Temperature fluctuations in the gas streams were estimated with a clipped Gaussian probability density function. The thermal energy balances and mass balances resulted in coupled systems of first-order differential equations, which were solved numerically. The model is capable of predicting NO production and magnetite oxidation in agreement with observation of plant performance. Although the design of the grate-kiln system is for efficient heat and mass transfer, it may not be the ...
The generation of acidic mine drainage is based on the oxidation dissolution of sulfide minerals due to the contact of ores with the natural water and the air. Namely, the sulfuric acid promotes the dissolution of sulfide minerals and gangue minerals, and Fe{sup 2+} is further oxidized to turn into Fe{sup 3+}, which acts as an oxidizer for other sulfide minerals and promotes the dissolution of the same. This paper roughly describes a mine drainage treatment focusing on an Fe{sup 2+} neutralization method and an iron bacteria oxidation method. The iron bacteria oxidation method is a method of oxidizing Fe{sup 2+} into Fe{sup 3+} by using iron bacteria, and then removing Fe{sup 3+} with calcium carbonate. This method has been used for treating the drainage in the Sakuhara Mine and the former Matsuo Mine, with good results. The paper finally introduces, as power-saving low-cost mine drainage treatment methods, a method of treating drainage ...
ObjectivesThe main objectives of this project are: 1. To determine whether nest-drifting behaviour allows helpers to maximise their indirect fitness in the paper wasp Polistes canadensis. Specifically, I will test a) whether nest-drifters apportion helping effort in relation to the productivity benefits of different nests (hypothesis 1a), and b) whether nest-drifters can adjust their investment in response to changes in the productivity payoffs of different nests (hypothesis 1b). 2. To determine [continued...]DescriptionDarwin's theory of natural selection predicts that organisms should act selfishly in order to pass on as many of their genes to the next generation as possible. The evolution of social behaviour is a paradox because it requires that some individuals forgo reproduction in order to help raise the offspring of others. Explaining the evolution of helping behaviour in animal societies has been a major focus for evolutionary ...
Two novel organic n-type semiconductors are investigated due to their function as electron acceptor for applications in organic electronic devices to widen the knowledge of how molecule structure influences the excitation processes in organic electronics. Bispyrenylfullerene and Octadecyl-Capronacidesterfullerene are C{sub 60} derivates with sidechains more featured compared to the commonly used[6,6] phenyl-C{sub 61}-butyric acid methyl ester (PCBM). In bulk heterojunction devices regioregular poly(3-hexylthiophene) (P3HT) was used as donor. The materials, pristine and in blend, were studied in view of light absorption, their quenching abilities of the P3HT photoluminescence as well as excited states. Furthermore, the spin state of the excited states was determined by light-induced electron spin resonance. Combining these complimentary experimental techniques, we obtained information on the generation of excited states, their nature, and the ...
A solution based on sludge and Olive oil mill effluent (OME) co-digestion, coupled with a management plan, has been implemented, to treat and dispose safely, the mixed residues, into the natural forest and agricultural land. The mixture of up to 25% OME to the sludge improved anaerobic degradation of phenols and fats. High density fat compounds, present in OME, enhanced aggregation, settling and acetoclastic activity of anaerobic sludge. The full scale unit, obtained by modification of a cold digester, allowed to set-up a low capital cost system. The system produced large quantity of biogas and electric energy. Anaerobic degradation of the mixture improved fertilizing properties, making feasible land application of the digested mixture. Regional plan based in Geographical Information System (GIS) selected 800 ha of adequate land area for application near the WWTP. The experience is technically and economically successful. Main incomes are provided by energy use and ...
Taiheiyo coal deashed using acid treatment and loaded with potassium or calcium was hydro-cracked under gaseous phase to discuss effects of these metals on liquefaction reaction. In addition, the loaded coal was added with red mud catalyst to examine effects of the addition. The loaded potassium has a softening power, and particularly the potassium adsorbed into surface and micropores in the coal decomposes selectively HI-BS and BI-PS and generates gas and HS. On the other hand, potassium deposited on coal surface promotes direct gas production from the coal. Irrespective of its loading modes, calcium has a catalytic nature to produce HI-BS selectively. Calcium also acts to impede decomposition of HI-BS into HS. Adding red mud catalyst to potassium loaded coal increases the inversion rate and the liquefaction yield, and most of the increase is accounted for by HI -BS, and BI-PS. When red mud catalyst is added to calcium loaded coal, the ...
Combustion of extremely fuel-rich ({phi}=4) methane/air mixtures at elevated pressures is investigated as a potential means to generate molecular hydrogen by non-catalytic partial oxidation. This system is investigated both computationally and experimentally. The computations use a perfectly-stirred reactor model and an explicit methane cool-flame mechanism to investigate the effects of reactor parameters on reaction time and product composition. Under adiabatic conditions, such mixtures are predicted to autoignite at low temperatures {approx}700 K for pressures exceeding 8.5 atm. Above 15 atm, conversion to products is complete in roughly 1 s. The dependence of reaction time and hydrogen yield is investigated as a function of inlet temperature, system pressure, and flame equivalence ratio. Actual product yields are measured in a tube reactor facility, and many of the predictions of the model, including long relaxation times to chemical equilibrium and temperatures ...
A technique has been developed for high resolution alpha particle spectroscopy from track length determination in CR-39 plastic. On individual tracks an energy resolution deltaE close to the range straggling limit is obtainable. For 6 MeV alpha-particle deltaE is proportional 35 keV on individual particles and for groups of particles deltaE proportional 20 keV can be achieved using certain data selection criteria. At 100 keV on individual particles deltaE is proportional 20 keV. The analysis requires 1) a knowledge of the track-etch rate (Vsub(T))-range relationship and 2) a theoretical understanding of alpha-particle track structure in CR-39 as a function of particle energy, dip angle and degree of etching. The structure of alpha-particle etched tracks in CR-39 is described and two methods of analysis discussed. Examples are given of the resolution attainable on tracks of alpha-particles as natural decay energy and from alpha-particles ...
Permian coal and Triassic mudstone from the Ordos Basin were pyrolyzed in a closed system using a gold tube technique. Carbon and hydrogen isotopes of the gases generated from pyrolysis were compared to Mesozoic gases in the basin to interpret the origin, maturity and any mixing of gases. Maturation trends for thermogenic methane from both coal and lacustrine kerogens in our experiment were found to be independent of heating rate, allowing their use for determination of gas provenance. Gases from a tectonically stable area like the Shanbei slope are derived mainly from Yanchang lacustrine kerogen, and gases in tectonically active areas consist of mixtures of coal-derived gases and oil-associated methane from deeply buried formations, as well as oil-associated gases and biogenic gases from shallow depth. The thermal maturity of the C{sub 2} and C{sub 3} gases is estimated to cover an equivalent vitrinite reflectance range from 0.7% to 1.2% R{sub o}, whereas C{sub 1} ...
Until now the assumption has been that synthesis gas - mixtures of carbon monoxide and hydrogen - would be the principal source for many of the chemicals and fuels to be made via C/sub 1/ chemistry. Efforts to make cheap synthesis gas continue. But the pressure to circumvent the stranglehold that OPEC has on petroleum has caused other avenues to be explored. The current oversupply of natural gas offers an interim solution to the problem of nonpetroleum alternate source materials for C/sub 1/ chemicals production. The paper discusses the constraints and advantages of four processes: conventional steam reforming, steam reforming with oxygen secondary, partial oxidation, and catalytic partial oxidation. The end product in all cases is methanol. Direct use of methanol as a fuel has encountered numerous difficulties. conversion of methanol is, thus, of more immediate interest in C/sub 1/ chemistry. The Mobil MTG process and its second-generation ...
(001) CZ silicon wafers were implanted with arsenic (As{sup +}) at energies of 10--50 keV to doses of 2 {times} 10{sup 14} to 5 {times} 10{sup 15}/cm{sup 2}. All implants were amorphizing in nature. The samples were annealed at 700 C for 16 hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As ...
(001) CZ silicon wafers were implanted with arsenic (As"+) at energies of 10--50 keV to doses of 2 x 10"1"4 to 5 x 10"1"5/cm"2. All implants were amorphizing in nature. The samples were annealed at 700 C for 16 hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As precipitation, As clustering and ...
A high-performance power system (HIPPS) is being developed. This system is a coal-fired, combined-cycle plant that will have an efficiency of at least 47 percent, based on the higher heating value of the fuel. The original emissions goal of the project was for NOx and SOx to each be below 0.15 lb/MMBtu. In the Phase 2 RFP this emissions goal was reduced to 0.06 lb/MMBtu. The ultimate goal of HIPPS is to have an all-coal-fueled system, but initial versions of the system are allowed up to 35 percent heat input from natural gas. Foster Wheeler Development Corporation is currently leading a team effort with AlliedSignal, Bechtel, Foster Wheeler Energy Corporation, Research-Cottrell, TRW and Westinghouse. Previous work on the project was also done by General Electric. The HIPPS plant will use a high-Temperature Advanced Furnace (HITAF) to achieve combined-cycle operation with coal as the primary fuel. The HITAF is an atmospheric-pressure, pulverized-fuel-fired ...
Burnable poisons are used in nuclear reactors to produce a more level distribution of power in the reactor core and to reduce to necessity for a large control system. An ideal burnable poison would burn at the same rate as the fuel. In this study, separation of neutron-absorbing isotopes was investigated in order to eliminate isotopes that remain as absorbers at the end of fuel life, thus reducing useful fuel life. The isotopes Gd-157, Dy-164, and Er-167 were found to have desirable properties. These isotopes were separated from naturally occurring elements by means of plasma separation to evaluate feasibility and cost. It was found that pure Gd-157 could save approximately $6 million at the end of four years. However, the cost of separation, using the existing facility, made separation cost- ineffective. Using a magnet with three times the field strength is expected to reduce the cost by a factor of ten, making isotopically separated burnable poisons a favorable ...
The desorption of uranium from the granular titanium-activated carbon composite adsorbent (concentration of uranium: 25.5 mg/l-Ad), which adsorbed uranium from natural sea water, was examined by the column process with acidic eluent at room temperature. The column operation was able to be carried out without destruction of the granular adsorbent by the generation of the carbon dioxide, and free from disturbance of the eluent flow by precipitate of calcium sulfate dihydrate with sulfuric acid eluent. The amount of acid consumption by the adsorbent was 0.87 eq/l-Ad. The alkaline earth metals were eluted in the range of elution volume below 2l/l-Ad, whereas uranium, iron, and titanium were eluted above 2l/l-Ad. Therefore, uranium was separable from the alkaline earth metals which were adsorbed in the most quantity in the adsorbent. In the range of elution volume 2 to 12l/l-Ad, the percentage of desorbed uranium and the concentration ratio of ...
Graphs with high symmetry or regularity are the main source for experimentally hard instances of the notoriously difficult graph isomorphism problem. In this paper, we study the computational complexity of isomorphism testing for line graphs of $t$-$(v,k,\\lambda)$ designs. For this class of highly regular graphs, we obtain a worst-case running time of $O(v^{\\log v + O(1)})$ for bounded parameters $t,k,\\lambda$. In a first step, our approach makes use of the Babai--Luks algorithm to compute canonical forms of $t$-designs. In a second step, we show that $t$-designs can be reconstructed from their line graphs in polynomial-time. The first is algebraic in nature, the second purely combinatorial. For both, profound structural knowledge in design theory is required. Our results extend earlier complexity results about isomorphism testing of graphs generated from Steiner triple systems and block designs.
The plasma plume generated by a new type of high energy Janitor known as the railplug, is examined. The railplug is a miniaturized railgun that has the potential for improving ignition characteristics of combustible mixtures in engines. The objective of the study is to gain an uderstanding of the characteristics of the plasma created by a transparent railplug, and to validate a multidimensional computer simulation of the plasma and shock fronts. The nature of the plume emitted by the railplug was examined for three levels of electrical energy while firing into air at a pressure of 1 atm. The computer model is to be used to predict trends in railplug performance for various railplug designs, energies, and ambient conditions. The velocity of the plasma movement inside a transparent railplug was measured, as well as the velocity of the plume ejected from the cavity. A shock is produced at the initiation point of the arc and propagates down the ...
The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) has been selected and computed with the heat mass balance program ENBIPRO. The results ...
Industrial segments as plant of mining, hospitals and university generate considerable volumes of radioactive wastewater containing uranium. The increasing development of the use of the nuclear energy to lead away to an expansion of the sectors of the nuclear fuel cycle, but it leads to security problems and it appears the necessity of control of the removing of uranium and radioactive effluent treatments. Researches evaluate if the technique of the biosorption would promote an alternative process with attractive characteristics of cost-benefit. The residual biomass from agricultural activities has been studied and used as adsorbent of metals and organic composts by low cost, abundance and for being biodegradable. In this work, it is presented the efficiency of the coir pith for the adsorption of ions UO_2"2"+. The coir pith is a by-product of the harvest of the coconut, a renewable natural source. The study was accomplished using the batch ...
This paper provides an overview of environmental cleanup at the Los Alamos National Laboratory (LANL) and some of the unique aspects and challenges. Cleanup of the 65-year old Department of Energy Laboratory is being conducted under a RCRA Consent Order with the State of New Mexico. This agreement is one of the most recent cleanup agreements signed in the DOE complex and was based on lessons learned at other DOE sites. A number of attributes create unique challenges for LANL cleanup -- the proximity to the community and pueblos, the site's topography and geology, and the nature of LANL's on-going missions. This overview paper will set the stage for other papers in this session, including papers that present: Plans to retrieve buried waste at Material Disposal Area B, across the street from oen of Los Alamos' commercial districts and the local newspaper; Progress to date and joint plans with WIPP for disposal of the remaining inventory of ...
The Potomac Electric Power Company generating station at Chalk Point, MD, utilizes brackish water in its natural draft cooling tower and, consequently, releases saline aerosol into the atmosphere. A research and monitoring project was established in 1974 to evaluate the effects of this drift on native perennial vegetation. Leaf samples have been collected form dogwood, Cornys florida, Virginia pine, Pinus virginiana, black locust, Robinia pseudoacacia, and sassafras, Sassafras albidum, located at 12 different sites in the vicinity of the power plant. Sampling was begun prior to the operation of the cooling tower, 1974, and continued through 1978. Complete results from monthly monitoring of foliar chloride in the four native tree species is documented for May through September 1978. Results from salt spray experiments indicate chloride and sodium concentrations in the wood of dogwood trees increases with increased spraying levels.
Boat sampling technique (BST) is a surface sampling technique, which has been developed for obtaining, in-situ, metal samples from the surface of an operating component without affecting its operating service life. The BST is non-destructive in nature and the sample is obtained without plastic deformation or without thermal degradation of the parent material. The shape and size of the sample depends upon the shape of the cutter and the surface geometry of the parent material. Miniature test specimens are generated from the sample and the specimens are subjected to various tests, viz. Metallurgical Evaluation, Metallographic Evaluation, Micro-hardness Evaluation, sensitisation test, small punch test etc. to confirm the integrity and assessment of safe operating life of the component. This paper highlights design objective of boat sampling technique, description of sampling module, sampling cutter and its performance evaluation, cutting process, ...
A 4-loop Pressurised Water Reactor (PWR) primary coolant system has been analysed for the postulated Loss of Coolant Accident (LOCA) event in order to derive peak dynamic loads for qualifying the design of equipment supports and pipe whip restraints. Pipe whip restraints as well as pipe and equipment supports are nonlinear by nature because of the presence of gaps and the different directional stiffnesses arising from snubber, steelwork and geometric and material interaction at the concrete to steel embedment. The different structural idealisations for the supports and restraints have an influence on the dynamic response of the structure. In the first of the two part paper a range of idealisation models for the Steam Generator and Reactor Coolant Pump vertical columns ranging from elastic stiffnesses to bilinear stiffnesses with or without preload were examined. Due to both structural and loading complexity, the behaviour of these supports were ...
The primary scope of this study is to establish the analysis technology for the advanced reactor designed on the basis of the passive and inherent safety concepts. This study is extended to the application of these technology to the safety analysis of the passive reactor. The study was performed for the small and medium sized reactor and the large sized reactor by focusing on the development of the analysis technology for the passive components. Among the identified concepts the once-through steam generator, the natural circulation of the integral reactor, heat pipe for containment cooling, and hydraulic valve were selected as the high priority items to be developed and the related studies are being performed for these items. For the large sized passive reactor, the study plans to extend the applicability of the best estimate computer code RELAP5/MOD3 which is widely used for the safety analyses of the reactor system. The improvement and ...
The European gas market is continuing to expand due to increased industrial, domestic and power generation demand. As a result of this demand, and the trend toward liberalization of the market, the need for storage of gas is also increasing. One key segment of the large scale storage of gas is underground storage, either in partially depleted gas or oil fields, naturally occurring caverns, aquifers and salt cavities. In most cases the gas produced after storage requires conditioning to meet the water of hydrocarbon dew point specification of the gas transmission system. For that reason export gas from storage will require gas conditioning in order to meet pipeline specifications. Adsorption as a feasible and reliable process will be presented in detail and especially in regards to hydrocarbon dew-pointing compared with other process options. (author)
The thermomechanical behaviour of clayey soils was examined in a laboratory study because of their importance in some engineering applications such as hydrocarbon extraction from oil-bearing sands and radioactive waste disposal. The slightest temperature variations have been known to have an impact on the mechanical behaviour of clayey soils. In this study, tests were conducted on reconstituted and natural clayey soils using triaxial cells modified to control temperatures. Changes of temperature and stress state were not applied simultaneously. Instead, the tests were divided into two separate sections aimed at studying the thermal and mechanical behaviour of clays. The thermal behaviour tests examined the deformations induced by drainage temperature changes as well as pore-pressure generation and consolidation phenomena. The mechanical behaviour tests, focused on the influence of temperature and temperature history on compressibility, ...
The French radioactive waste management act of December 30, 1991, included two key provisions. It initiated a major research program with three areas of investigation concerning high-level long-lived radioactive waste management routes, and called for the Government to submit a legislative proposal to Parliament within 15 years (by 2006) specifying the policy guidelines adopted. Considering the sensitive nature of the subject, the questions surrounding the issue of radioactive waste, and the social, economic and environmental concerns for present and future generations, the Government has inaugurated, in 2005, a nationwide public debate on these issues between the submittal of the research reports and the parliamentary discussion of the proposed law. In this context, the CEA has decided to concentrate at Marcoule the expertise and experience acquired in the area of radioactive waste management and to make it available to stakeholders and to the ...
The role of helium in a process of embrittlement and hardening of RAFM steels was investigated in EUROFER97 based experimental heats, ADS2, ADS3 and ADS4, that were doped with different contents of natural B and the separated 10B-isotope (0.008-0.112 wt.%). The neutron irradiation of the boron doped and the reference RAFM steels was performed in the Petten High Flux Reactor up to 16.3 dpa at different temperatures between 250 and 450 deg. C. The embrittlement behaviour and hardening was investigated by instrumented Charpy-V tests with subsize specimens. Irradiation lead to generation of 84, 432 and 5580 appm He in ADS2, ADS3 and ADS4 steels, respectively. At irradiation temperatures Tirr ? 350 deg. C the boron doped steals show progressive embrittlement and reduction of toughness with increasing helium amount. The analysis of the hardening vs. embrittlement behaviour at Tirr ? 350 deg. C reveals hardening nature of ...
Naturally Occurring Radioactive Material (N.O.R.M.) occurs in most soil and rock, and by mining and mineral processing, some of the radionuclides are significantly enhanced. An in-situ gamma-ray detector called M.E.D.U.S.A., has been used to produce a map of relative activity concentrations in a gold mine tailings dam on the Witwatersrand in South Africa. A CsI(Na) scintillation detector is used in this system. M.E.D.U.S.A. spectra obtained from the survey were analyzed using the Full-Spectrum Analysis (F.S.A.) procedure to compute the {sup 40}K, {sup 238}U and {sup 232}Th activity concentrations. The activity concentrations are used with global positioning data (G.P.S.) to produce the concentration maps. A hyper-pure germanium gamma-ray detector (Hp Ge) was used to measure gamma-rays from the naturally occurring nuclides for soil samples taken at different points on the site to calibrate the M.E.D.U.S.A. system. Radon soil gas measurements ...
A design for passive cooling of large containment structures has progressed sufficiently to move forward into the detailed design stage necessary for plant construction. For such application, a safety analysis report has already been submitted to the US Nuclear Regulatory Commission. The design considers an annulus between the inner steel containment vessel and outer, thick-walled concrete shield building with chimney-like natural convection cooling driven only by a density gradient relative to the atmosphere. Air within the annulus is heated as internal containment temperature rises and heat is transferred through the steel containment shell. The resulting air density gradient between the annulus and the environment causes the heated air to rise, producing a natural convection flow through inlets in the shield building, past the steel shell, and out an exit chimney. Several options for enhancing passive heat removal of large containment ...
A numerical simulation of two-dimensional laminar natural convection in a fully open tilted square cavity with an isothermally heated back wall is conducted. The remaining two walls of the cavity are adiabatic. Steady-state solutions are presented for Grashof numbers between 10{sup 2} and 10{sup 5} and for tilt angles ranging from {minus}60{degree} to 90{degree} (where 90{degree} represents a cavity with the opening facing down). The fluid properties are assumed to be constant except for the density variation with temperature that gives rise to the buoyancy forces, which is treated by the Boussinesq approximation. The fluid concerned is air with Prandtl number fixed at 0.71. The governing equations are expressed in a normalized primitive variables formulation. Numerical predictions of the velocity and temperature fields are obtained using the finite-volume-based power law (SIMPLER: Semi-Implicit Method for Pressure-Linked Equations Revised) algorithm. For a ...
Once again Brazil faces the possibility of an electricity shortage in the near future. The low level of rain and the consequent reduction of hydroelectric reservoirs (hydroelectric energy represents almost 80% the total Brazilian electricity generation) led to the dispatch of thermal plants based on natural gas and/or fuel oil. However, the recent crisis regarding the Bolivian natural gas supply to Brazil increased the risk of a shortage of this energy source. Hence, the uncertainty of the electricity supply scenario is pushing the electricity prices up in the near future. A possible alternative to increase the electricity supply is the maximization of the electricity surplus in sugarcane mills. Back in 1970's and 1980's, cogeneration plants in sugarcane mills were primarily designed to consume all bagasse, and produce steam and electricity to the process. The plants used medium pressure steam boilers (21 ...
The Ordos Basin, the second largest sedimentary basin in China, contains the broad distribution of natural gas types. So far, several giant gas fields have been discovered in the Upper and Lower Paleozoic in this basin, each having over 1000x10{sup 8}m{sup 3} of proven gas reserves, and several gas pools have also been discovered in the Mesozoic. This paper collected the data of natural gases and elucidated the geochemical characteristics of gases from different reservoirs, and then discussed their origin. For hydrocarbons preserved in the Upper Paleozoic, the elevated {delta}{sup 13}C values of methane, ethane and propane indicate that the gases would be mainly coal-formed gases; the singular reversal in the stable carbon isotopes of gaseous alkanes suggests the mixed gases from humic sources with different maturity. In the Lower Paleozoic, the {delta} {sup 13}C{sub 1} values are mostly similar with those in the Upper Paleozoic, but the ...
The Asian countries are expected to generate 45% of the world energy consumption and Japan is the absolutely greatest consumer in Asia, but China is the country that will be most important as a new consumer on the world energy markets. China, like India and later possibly even Japan try to change to natural gas as a source of energy as much as possible. This is causing a competition about the resources that can be reached by pipelines for gas, which in practice means those in Russia and Central Asia. Russia is trying to control the gas in Central Asia. The competition is also increasing about oil. China is becoming heavily dependent on Muslim countries in the Middle East and Central Asia. This also leads to an effort to increase the safety along the sea lanes, which may collide with the interests of other countries. Territorial conflicts with gas and oil as underlying elements exist in Asia. USA is a player on the energy market, who is using ...
Metal waste generated from domestic nuclear operation for defense and commercial application has led to a growing stockpile of radioactively contaminated scrap metal, much of which is stainless steel. A significant fraction of this material cannot be efficiently surface decontaminated. The burial of this material would be wasteful and expensive, since long term monitoring would be necessary in order to minimize environmental risk. Much of this waste consists of bulky equipment. In many case, this equipment contains valuable material that may be recycled. The piece of equipment considered frequently also has complex geometries, making extremely difficult, time-consuming and expensive to determine the exact location and level of radioactivity on the internal surfaces. After melting, however, the radioactivity may be precisely determined from samples of each ingot. Moreover, an ingot may be released for restricted or unrestricted reuse, or stored for decay to ...
This report is intended to satisfy two concurrent needs: (1) provide a contract deliverable from Oncorh Consulting to the Washington Department of Fish and Wildlife (WDFW), with emphasis on identification of salient results of value to ongoing Yakima/Klickitat Fisheries Project (YKFP) planning and (2) summarize results of research that have broader scientific relevance. This is the fourth in a series of reports that address reproductive ecological research and monitoring of spring chinook populations in the Yakima River basin. This annual report summarizes data collected between April 1, 2004 and March 31, 2005 and includes analyses of historical baseline data, as well. Supplementation success in the Yakima Klickitat Fishery Project's (YKFP) spring chinook (Oncorhynchus tshawytscha) program is defined as increasing natural production and harvest opportunities, while keeping adverse ecological interactions and genetic impacts within acceptable bounds ...
The effect of adding hydrogen to methane as a fuel for spark ignited engines has been extensively investigated. Both the possibility of adding a limited amount of hydrogen as well as equal amounts of hydrogen and carbon dioxide to natural gas has been investigated. A 10 vol% addition of hydrogen to the natural gas caused a reduction in UHC of approximately 40%, and an increase in efficiency of approximately three percentage points at the test engine. It is unknown if the gain is representative for large engines. Similar results for UHC reduction and efficiency were obtained for combined hydrogen and carbon dioxide addition. The carbon dioxide was added by exhaust gas recirculation. However, the price of hydrogen, makes this idea uneconomical even when carbon dioxide is readily available through recirculation of engine exhaust. Adiabatic prereforming may be used to convert natural gas into methane, hydrogen and carbon ...
The production, principal applications, characteristics and properties, advantages of the gas natural is showed. A sectorial overview of the ceramic industry and the utilization of the natural gas in the ceramic industry is presented. The expectations are systematized and the impact of the natural gas utilization in the ceramic industry is evaluated. Some conclusions are withdrawn and recommendations suggested.
... Author: Radev, Dragomir R. Subjects: natural language processing DeweyClass: 764 Resource type: document Natural Language Processing Research Group Research Group based in the Department of Computer Science, University of Sheffield. Conducts research into natural language analysis topics including data mining/information extraction, dialogue, and semantics. Author: Department of Computer Science, University of Sheffield Subjects: natural language processing DeweyClass: 764 Resource ...
The most developed systems for the generation of electricity from coal are the Integrated coal Gasification Combined Cycle (IGCC) and the Pressurized Fluidized Bed Combustion (PFBC) system. They both represent state-of-the-art technology and provide electric power at 41-46% LHV efficiency. However, the high level of complexity leads to lower reliability and higher costs. A simpler system, based on a coal-fired steam boiler integrated with a gas turbine, has been proposed. In such a plant, known as the externally fired combined cycle (EFCC), compressed air is heated indirectly in a heat exchanger located in the coal furnace. The hot air is then expanded in a turbine, and the exhaust is passed on to the coal furnace as preheated combustion air. Steam produced in the boiler generates additional power in a steam turbine. The exclusion of coal combustion products from the gas turbine avoids hot gas clean-up and turbine blade corrosion by coal ash. ...
The Asia-Pacific region will see tremendous growth in demand for electricity in the next few decades and will be an important market for generation equipment and associated services. The Association of Southeast Asian Nations (ASEAN) countries alone anticipate additional power demand of more than 37,000 NM by the year 2000, with an estimated total expenditure of US $85 billion. Trends in recent years show natural gas-fired combined cycle in plants to be fast gaining in popularity over conventional thermal plants. The advantages include increased primary energy conversion efficiency coupled with significant reduction in pollutant emissions, shorter construction times, faster loading rates and reduced staffing requirements. In the computer model used for generation capacity expansion planning in Tenaga Nasional Berhad, clean coal technology models are not used as candidate plants. In the opinion of the authors, this results ...
In this paper an analysis will be performed to assess the economical competitiveness of Nuclear Power against other base load technologies. There are several plans to build more nuclear power plants in western countries; these plans are result among other things of the fossil fuel high prices and the concern for the global warming. France started the construction of one EPR at Flamanville in 2007 and at the end of 2008 there were 17 applications before NRC for construction and operation licenses (COL) to build as much as 26 new reactor units in USA, among the designs selected are the US-EPR, APWR, ESBWR, ABWR and AP1000. Currently, there is a lot of uncertainty about what is the overnight cost for a new generation III nuclear power plant and the vendors are not providing too much information. However, it is expected that under the new economy conditions the overnight cost will be between 2500 and 3500 USD/kW, the output electricity power of the units mentioned ...
Back in 1985 it was the European Commission's intention to demonstrate on rather large scale the provision of clean and renewable energy with hydrogen as energy vector and fuel. The cheapest and technologically available form of renewable electricity, the primary energy for electrolytic hydrogen, is hydropower. Most of the hydroenergy sources are oversea's. The World's topologically and technically exploitable hydroenergy potential is estimated to be in the order of 20.10{sup 3} TWh/y, i.e. 0.0057% of the hydraulic cycle energy. Today's hydroelectricity generation is {approx}2500 TWh/y i.e. {approx}21% of the World's electricity generation. Quebec's installed hydroelectricity is 33.5 GW, its residual potential is 50 GW or 190 TWh/y and 285 TWh/y, respectively (load factor 0.65). The construction of hydropower installation is rather clean. The construction of La Grande at James Bay with an ...
The MTX experiment was proposed in 1986 to apply high frequency microwaves generated by a free-electron laser (FEL) to electron cyclotron resonance heating (ECRH) in a high field, high density tokamak. As the absorption of microwaves at the electron cyclotron resonance requires high frequencies, the opportunity of applying a free-electron laser has appeal as the device is not limited to frequencies in the microwave or long millimeter wavelength regions, in contrast to many other sources. In addition, the FEL is inherently a high power source of microwaves, which would permit single units of 10 MW or more, optimum for reactors. Finally, it was recognized early in the study of the application of the FEL based on the induction linear accelerator, that the nonlinear effects associated with the intense pulses of microwaves naturallygenerated would offer several unique opportunities to apply ECRH to current drive, MHD control, ...
A case study of a hypothetical offshore production fixed leg platform facility is presented. The purpose of the case study is to demonstrate the advantages offered by modern, fuel efficient large gas turbines in central power generation service for offshore production. The case study was presented using the Rolls- Royce RB211 large gas turbine with facility production of approximately 240,000 BPD of oil and 540 MMSCFD of associated gas. The gas was subjected to three stages of separation for removal of hydrocarbon liquids and water. The liquids, natural gas, and crude oil were exported from the production platform to an onshore receiving terminal. Gas compression is the service that requires the greatest amount of power for any given production facility. For this case study, gas compression represented approximately 70 per cent of the power load with the remainder represented by the liquid export pumps (16 per cent), and by general utilities ...
To use such sites very effectively, pile foundations will be used for soil stabilization and for important structures for the prevention of subsidence. Negative friction that may ensue from the differential settlement of the soil has to be prevented. Measures against gas will include gas collecting and exhausting facilities in the lower parts of structures, natural and forced exhaust systems, and gas detection/warning units. For revegetation, plants strong against bad soil should be selected, they should be protected from generated gas with protecting sheets or the like, and a thick layer of vegetation-capable soil needs to be laid. Replacement, compaction, and solidification are the fundamentals of soil improvement at wastes final treatment locations and of soil-related pollution prevention in the vicinity of the newly produced sites. Across the country, the service life expectancy is approximately 7-8 years for general wastes and ...
The Externally-Fired Combined Cycle (EFCC) is an attractive emerging technology for powering high efficiency combined gas and steam turbine cycles with coal or other ash bearing fuels. In the EFCC, the heat input to a gas turbine is supplied indirectly through a ceramic air heater. The air heater, along with an atmospheric coal combustor and ancillary equipment, replaces the conventional gas turbine combustor. A steam generator located downstream from the ceramic air heater and steam turbine cycle, along with an exhaust cleanup system, completes the combined cycle. A key element of the EFCC Development Program, the 25 MMBtu/h heat-input Kennebunk Test Facility (KTF), has recently begun operation. The KTF has been operating with natural gas and will begin operating with coal in early 1995. The US Department of Energy selected an EFCC repowering of the Pennsylvania Electric Company`s Warren Station for funding under the Clean Coal Technology ...
The core bypass flow in a prismatic very high temperature reactor (VHTR) is an important design consideration and can have considerable impact on the condition of reactor core internals including fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) are affected by bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to better understand bypass flow phenomena and establish an evaluation method for the reactor core using the commercial CFD code FLUENT. Parametric calculations changing several factors ...
The core bypass flow in a prismatic very high temperature gas-cooled reactor (VHTR) is one of the important design considerations which impacts considerably on the integrity of reactor core internals including operating fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) will be affected by the bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to understand better the bypass flow phenomenon and establish the evaluation method in the reactor core using commercial CFD code FLUENT. Parametric ...
of Colorado at Boulder Search This Site Natural Hazards Observer Disaster Research CU Web Site CU People go Search This Site Natural Hazards Observer Disaster Research CU Web...
This thesis analyzes Egyptian political culture and the directive effect which it has upon political development, elite recruitment and the nature of political participation. The pervasive nature of Islam and the centrality of kinship remain the basic fac...
The different radiation loads caused by natural and artificial radionuclides are compared in this paper. This examples will serve to illustrate that the problem of population exposure to radiation can only be solved in consideration of all components and to show which effects of the radiation from natural sources are of special importance in this connexion. (orig./AK).
The radionuclide characteristics of light-water-reactor (LWR) spent fuel play key roles in the design and licensing activities for radioactive waste transportation systems, interim storage facilities, and the final repository site. Several areas of analysis require detailed information concerning the time-dependent behavior of radioactive nuclides including (1) neutron/gamma-ray sources for shielding studies, (2) fissile/absorber concentrations for criticality safety determinations, (3) residual decay heat predictions for thermal considerations, and (4) curie and/or radiological toxicity levels for materials assumed to be released into the ground/environment after long periods of time. The crucial nature of the radionuclide predictions over both short and long periods of time has resulted in an increased emphasis on thorough validation for radionuclide generation/depletion codes. Current radionuclide generation/depletion ...
The situation of natural gas in the Federal Republic of Germany is described, with particular emphasis on the advantages and consequences of natural gas supply. The brochure discusses the role of natural gas on the energy market, the reliability of natural gas supply, the environmental impacts, the energy-saving effect of natural gas, natural gas prices, the competitive strength of the German gas industry, and the long-term reliability of natural gas supply. (orig.) [German] Die Situation des Erdgases in der Bundesrepublik Deutschland wird beschrieben, wobei die wichtigsten Vorteile und Auswirkungen der Erdgasversorgung besonders hervorgehoben werden. Es geht um die Stellung des Erdgases im Energiemarkt, die Sicherheit der Energieversorgung, Umweltschutz, Energieeinsparung durch Erdgaseinsatz, Erdgaspreise, Leistungsfaehigkeit der deutschen ...
Humans, like other animals, are exposed to a continuous stream of signals, which are dynamic, multimodal, extended, and time varying in nature. This complex input space must be transduced and sampled...Full Text Available
The present study describes an efficient chemoenzymatic method for introducing a core N-glycan of glycoprotein origin into various lipophilic natural products. It was found...Full Text Available
The methods are described of determining natural radionuclides, viz., thorium, uranium, radium, radon, polonium, actinium, and protactinium. The analysis is also described of ores, rocks, minerals, water, air. (M.D.).
This patent describes an ignition system of an internal combustion engine which consists of: a permanent magnet supported by a rotary member of the engine adapted to rotate in synchronism with a rotary shaft of the engine; a generating coil for generating an electromotive force to produce an electric current as the permanent magnet acts on the generating coil during the rotation of the rotary member; an ignition capacitor charged by the electric current generated by the generating coil; a thyristor caused to turn on by a counter electromotive force generated by the generating coil to thereby cause the ignition capacitor to begin to discharge; and an ignition coil generating a high voltage as the ignition capacitor begins to discharge, to cause a spark discharge to take place in an ignition plug of the internal combustion ...
For the CREYS MALVILLE plant, sodium natural convection has been considered in connection with certain upset, faulted or beyond design basis situations. For each of these cases, this paper will discuss why natural convection was considered, the main conclusions reached and the natural convection tests which will be performed at plant start-up.
The budding natural gas markets in East Europe attract a great deal of interest from natural gas industries in the Western countries. Dutch companies, institutions and the government, too, are active in this market. So far the results have not been spectacular. An analysis is made of the present situation and the Dutch approach
... harassment, incidental to construction and operation of an offshore liquefied natural gas (LNG) facility. Under the Marine Mammal Protection ... ...
Biomass is one of the main natural resources in Sweden. The present low-CO{sub 2} emission characteristics of the Swedish electricity production system (hydro and nuclear) can be retained only by expansion of biofuel applications for energy purposes. Domestic Swedish biomass resources are vast and renewable, but not infinite. They must be utilized as efficiently as possible, in order to make sure that they meet the conditions for sustainability in the future. Application of efficient power generation cycles at low costs is essential for meeting this challenge. This applies also to municipal solid waste incineration with energy extraction, which should be preferred to its dumping in landfills. Hybrid dual-fuel combined cycle units are a simple and affordable way to increase the electric efficiency of biofuel energy utilization, without big investments, uncertainties or loss of reliability arising from complicated technologies. Configurations of ...
For heavy-ion beam driven inertial fusion ''liquid-protected'' reactor designs such as HYLIFE-II, a mixture of molten salts made of F{sup 10}, Li{sup -6}, Li{sup 7} and Be{sup 9} (called flibe) allows small chambers and final-focus magnets closer to the target with superconducting coils suffering higher radiation damage, though they can stand only a certain amount of energy deposited before quenching. This work has been primarily focusing on verifying that total energy deposited by fusion neutrons and induced gamma rays remain under such limit values and the final purpose is the optimization of the shielding of the magnetic lens system from the points of view of the geometrical configuration and of the physical nature of the materials adopted. The system is analyzed in terms of six geometrical models going from simplified up to much more realistic representations of a system of 192 beam lines, each focused by six magnets. A 3-D ...
ABS>A horizontal steam generator design for the SM-2 was lysis to determine the per formance of such a steam generator under steady state operating conditions and during load transients, The configuration for this design is a two- drum unit consisting of a heat exchanger unit and separator drum interconnected by integral riser and downcomer. An analog computer was used to analyze the steam generator behavior Wring load transients. The effect of various design changes on the response of the steam generator to step chages in load was determined. The horizontal steam generator design was compared to the existing vertical steam generator design for weight, size, price, and performance. (auth)
Ruthenium is one of the fission products in the reprocessing of irradiated fuels that requires a specific processing management. Its elimination, upstream by the PUREX process, has been considered. A process, called electro-volatilization, which take advantage of the RuO{sub 4} volatility, has been optimised in the present study. It consists in a continuous electrolysis of ruthenium solutions in order to generate RuO{sub 4} species that is volatilized and easily trapped. This process goes to satisfying ruthenium elimination yields with RuNO(NO{sub 3}){sub 3}(H{sub 2}O){sub 2} synthetic solutions but not with fuel dissolution solutions. Consequently, this work consisted in the speciation studies of dissolved ruthenium species were carried out by simulating fuel solutions produced by hot acid attack of several ruthenium compounds (Ru(0), RuO{sub 2},xH{sub 2}O, polymetallic alloy). In parallel with dissolution kinetic studies, the determination of dissolved species ...
The purpose of this work is to characterize the role of the financial institutions in achieving sustainable development meaning a process of development which leaves at least the same amount of capital, natural and man-made, to future generations as current generations have access to. This makes it clear that sustainable development is about capital allocation and thus should be at the core of financial markets activity. On a more practical level the different ways banks affect environment are analyzed: as investors - supplying the investments with environmental perspective; as lenders - developing new financial products to encourage sustainable development; as valuers - estimating risks and opportunities in project-financing; as powerful stake holders - as shareholders and lenders they can exercise considerable influence over companies; - as polluters - while not dirty industries, financial institutions do consume ...
A study was conducted to examine the energy consumption in existing and new hog farming facilities and to analyse the potential for increased natural gas use in the Saskatchewan hog industry. Existing heating/cooling, ventilation and feed mill equipment choices offer possibilities for running on electricity, natural gas or propane. Energy costs are lowest when natural gas is used. To put the study in context, an overview of the Saskatchewan hog industry was provided. The potential increase in natural gas use in hog production by year 2005 was estimated. 10 refs., 6 tabs., 8 figs.
Increased use of natural gas has positive effects for the environment and the climate, because it primarily replaces petroleum products. Moreover, the natural gas does not pose a threat to bio fuel in Norway. But introducing CO2 taxes on natural gas will significantly increase the emission of greenhouse gases, concludes a report conducted by Norsk Energi (Norwegian Energy) on behalf of Norsk Naturgassforening (Norwegian Natural Gas Association) and Norsk Gassforum (Norwegian Gasforum). A brief presentation of the main conclusions in the report (ml)
Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and cleaner method which has different heat ...
Design process of steam generator and condenser at Russian nuclear power plant type WWER-1000 is identified. The four chapter of the books are organized as nuclear power plant, types of steam generators specially horizontal steam generator, process of steam generator design and the description of condenser and its process design.
This paper provided an outline of the Canadian natural gas commodity market and a forecast for Canadian natural gas supply and prices for the 2007 winter heating season. Since 2001, steady demand growth and slow supply growth have contributed to higher North American natural gas commodity prices. The loss of natural gas supply due to hurricanes pushed North American natural gas commodity prices to record levels in 2005. Canadian natural gas production levels currently exceed domestic gas consumption. In 2005, Canada produced 16.5 billion cubic feet per day of marketable natural gas. Approximately 45 per cent was consumed domestically, and the remainder was exported to the United States. Despite high levels of drilling activity, production of natural gas from western Canada has flattened out since 2001. In 2006, ...
Herpes simplex virus type-1 (HSV-1) entry into target cell is initiated by the ionic interactions between positively charged viral envelop glycoproteins and a negatively charged cell surface heparan sulfate (HS). This first step involves the induction of HS-rich filopodia-like structures on the cell surface that facilitate viral transport during cell entry. Targeting this initial first step in HSV-1 pathogenesis, we generated different zinc oxide (ZnO) micro-nano structures (MNSs) that were capped with multiple nanoscopic spikes mimicking cell induced filopodia. These MNSs were predicted to target the virus to compete for its binding to cellular HS through their partially negatively charged oxygen vacancies on their nanoscopic spikes, to affect viral entry and subsequent spread. Our results demonstrate that the partially negatively charged ZnO-MNSs efficiently trap the virions via a novel virostatic mechanism rendering them unable to enter into human corneal ...
ICU telemedicine uses audiovisual conferencing technology to provide critical care from a remote location. Research is needed to best define the optimal use of ICU telemedicine, but efforts are hindered by methodological challenges and the lack of an organized delivery approach. We convened an interdisciplinary working group to develop a research agenda in ICU telemedicine, addressing both methodological and knowledge gaps in the field. To best inform clinical decision-making and health policy, future research should be organized around a conceptual framework that enables consistent descriptions of both the study setting and the telemedicine intervention. The framework should include standardized methods for assessing the preimplementation ICU environment and describing the telemedicine program. This framework will facilitate comparisons across studies and improve generalizability by permitting context-specific interpretation. Research based on this framework should consider the ...
LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level {alpha} solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination factor differs and depends on the ruthenium concentration, harmful ...
LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level #alpha# solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination factor differs and depends on the ruthenium concentration, harmful ...
Various engine concepts that are in the race to be the dominant bus-engine type five years from now were reviewed. Three types of engines, the Otto cycle (CNG and propane), diesel and DME (dimethyl ether) received most of the attention. Emission standards, engine size and reliability are the main demands on bus engines. Each of these engine concepts were reviewed against these criteria. In terms of emission standards (as measured by the EEV emission limits) Otto cycle engines have the advantage since they are currently in production. Advanced diesel technology is on the prototype level, but not yet in production. DME-engines are still on the testbed, not in the demonstration stage and much less in the production stage. Otto cycle engines also have the most experience with EEV emission limits. Among the Otto-cycle engines, propane-fuelled engines appear to have the upper hand since propane is very cost-effective, whereas CNG tanks and infrastructure are expensive. Diesel engines have ...
Most of all research reactors are immerged in the deep water pool to be a ultimate heat sink. At the neighbor of the reactor, some radio-active matters, such as Na-24, Ar-41, Mg-27, Al-28 and etc, may be generated by the neutron irradiation. Those radio-active isotopes may rise up to the pool water surface through the natural convection flow, which can make the radioactivity in the reactor hall rise high enough to concern about the health of people working in the reactor hall. When the irradiation test facilities are loaded or unloaded during a normal operation, the highly radio-activated primary coolant may flow out through the irradiation test holes on the top of the reactor. This also may be a main hazard source to make the working environment of the reactor hall bad. Making a hot water layer 1.5 ? 2.0 m thick at the top of reactor pool would be a good measure to resolve that problem. The hot water layer is formed by a thermal stratification ...
As recently as 1950, 30% of the world's population lived in urban areas. By the year 2030, 60% of the world's population will live in cities, according to the United Nations 'World Population Prospects Revision Report' (2001). Urbanization is quickly transitioning communities from natural rural vegetation to man-made urban engineered infrastructure. This anthropogenic-induced change has manifested itself in microscale and mesoscale increases in temperatures in comparison to adjacent rural regions which is known as the Urban Heat Island Effect. The resultant change causes potentially adverse consequences for local and global communities. One of the great challenges facing our current generation of scientists and engineers is how to support the growth of new and existing urban centers in a sustainable manner. This is even more pronounced in arid regions, which will sustain the greatest rate of urbanization. ...
The assets that Citizen Potawatomi Nation holds were evaluated to help define the strengths and weaknesses to be used in pursuing economic prosperity. With this baseline assessment, a Planning Team will create a vision for the tribe to integrate into long-term energy and business strategies. Identification of energy efficiency devices, systems and technologies was made, and an estimation of cost benefits of the more promising ideas is submitted for possible inclusion into the final energy plan. Multiple energy resources and sources were identified and their attributes were assessed to determine the appropriateness of each. Methods of saving energy were evaluated and reported on and potential revenue-generating sources that specifically fit the tribe were identified and reported. A primary goal is to create long-term energy strategies to explore development of tribal utility options and analyze renewable energy and energy efficiency options. Associated goals are to ...
The Army Reactor Area (ARA) II was constructed in the late 1950s as a test site for the Stationary Low Power Reactor No. 1 (SL-1). The SL-1 was a prototype power and heat source developed for use at remote military bases using a direct cycle, boiling water, natural circulation reactor designed to operate at a thermal power of 3,000 kW. The ARA II compound encompassed 3 acres and was comprised of (a) the SL-1 Reactor Building, (b) eight support facilities, (c) 50,000-gallon raw water storage tank, (d) electrical substation, (e) aboveground 1,400-gallon heating oil tank, (f) underground 1,000-gallon hazardous waste storage tank, and (g) belowground power, sewer, and water systems. The reactor building was a cylindrical, aboveground facility, 39 ft in diameter and 48 ft high. The lower portion of the building contained the reactor pressure vessel surrounded by gravel shielding. Above the pressure vessel, in the center portion of the building, was a turbine ...
The mass generation in the Standard Model of Particles Physics relies on a spontaneous symmetry breaking mechanism. Its implementation is recalled, along with its constraints, both theoretical (Naturalness, Stability, Triviality, Unitarity) and experimental (limits of direct and indirect searches, prospects). Calculation techniques for observables evaluation in Perturbative Field Theory are described, particularly Helicity Amplitude method, which is given in details: fermions and vector bosons, massless and massive. Monte-Carlo integration, and structure functions approximations (which allows non-perturbative calculations) are also detailed. With these tools, a process giving to Physics beyond the Standard Model is studied: it leads to an experimental prediction for the LEP collision ring, taking the classical background into account. Technical aspects of a future photon linear collider are reviewed. The production of heavy vector bosons, ...
The paper examines science fiction literature as a product and part of the social consciousness of the modern capitalist world order. This world order is seen as emphasizing science, technology, movement, growth, urbanization, industrialization, complex organization, and progress. The document is organized into two sections. The first section reviews theories of the sociology of knowledge and discusses knowledge as a process of self-production and reproduction of society. Influential theorists include Hegel, Marx, Lukacs, Mannheim, Gramsci, Habermas, and Touraine. Touraine's (1977) dynamic conflict-based systematic theory of society is based on three concepts: historicity, which defines the instruments of society's self-production; the system of historical action which is the totality of social and cultural orientations, by means of which historicity exercises its control of historicity and the system of historical action. The second section discusses science fiction as a process of ...
This paper describes research and development activities at the University of Regina, Saskatchewan, Canada on Optimization of CO{sub 2} Extraction Process Technologies. The ultimate goal of this research is to develop better and more effective CO{sub 2} separation processes which can be used to recover CO{sub 2} from industrial sources such as coal-fired power plants and coal gasification complexes at the lowest possible capital and operating costs. The research program has been supported by Saskatchewan Power Corporation, Saskatchewan Energy and Mines, Prairie Coal Ltd., the Canada Centre for Mineral and Energy Technology (CANMET), Fluor Daniel Inc. (USA), Sulzer Chemtech (Switzerland), Wascana Energy Inc., and Natural Sciences and Engineering Research Council of Canada (NSERC). Currently, six parallel and complementary projects have been carried out at the Process Systems Laboratory. These projects are: (1) Searching for new sterically hindered amines for high ...
To assess the technical feasibility of a newly designed stent-like electrode in rabbits. A stent-like electrode was knitted from a single thread of nitinol wire and interconnected to a generator using similar wire. In order to gauge the extent of radiofrequency ablation (RFA), we measured the depth of the ablated area in cow liver using a combination of 180-sec time intervals and 20- watt power increments. For data processing, Cox regression analysis was used. RFA was also applied to the small intestine of rabbits using this stent-like electrode under six different sets of conditions: 10 watts for 1 min, 10 watts for 2 mins, 20 watts for 1 min, 20 watts for 2 mins, 30 watts for 1 min, and 30 watts for 2 mins. To determine the gross and microscopic findings, six animals were sacrificed immediately after the procedure and the results obtained under the different sets of conditions were correlated. Eight rabbits were monitored for 4 weeks prior to sacrifice. For both ...
In attempting to detect and map out underground facilities, whether they be large-scale hardened deeply-buried targets (HDBT's) or small-scale tunnels for clandestine border or perimeter crossing, seismic imaging using reflections from the tunnel interface has been seen as one of the better ways to both detect and delineate tunnels from the surface. The large seismic impedance contrast at the tunnel/rock boundary should provide a strong, distinguishable seismic response, but in practice, such strong indicators are often lacking. One explanation for the lack of a good seismic reflection at such a strong contrast boundary is that the damage caused by the tunneling itself creates a zone of altered seismic properties that significantly changes the nature of this boundary. This report examines existing geomechanical data that define the extent of an excavation damage zone around underground tunnels, and the potential impact on rock properties such as P-wave and ...
In August 1989, representatives from the Alberta Oil Sands Technology and Research Authority (AOSTRA) were the guests of the USSR Interbranch Scientific Technological Complex, Oil Recovery Institute (MNTK) in an extensive visit to heavy oil and gas fields and to various research institutes. Observations made during this tour concerning developments in the USSR heavy oil/bitumen industry, enhanced oil recovery, research programs, proposals for joint ventures, and technological developments are reported. It is noted that oil production in the USSR seems to have peaked and is in a state of decline, indicating the vital importance of enhanced recovery projects in reversing this trend. The areas visited included the Yarega field, where underground thermal recovery methods are used; the Sakhalin Island area, where successful thermal methods are used and where the USSR's largest offshore drilling rig is located; the Krasnodar/Black Sea area, where MNTK's Nefteotdacha ...
Synthetic atrial natriuretic peptide (carperitide) and B-type natriuretic peptide (BNP; nesiritide) are used to treat congestive heart failure. However, despite beneficial cardiac unloading properties, reductions in renal perfusion pressures limit their clinical effectiveness. Recently, CD-NP, a chimeric peptide composed of C-type natriuretic peptide (CNP) fused to the C-terminal tail of Dendroaspis natriuretic peptide (DNP), was shown to be more glomerular filtration rate-enhancing than BNP in dogs. However, the molecular basis for the increased responsiveness was not determined. Here, we show that the DNP tail has a striking effect on CNP, converting it from a non-agonist to a partial agonist of natriuretic peptide receptor (NPR)-A while maintaining the ability to activate NPR-B. This effect is specific for human receptors because CD-NP was only a slightly better activator of rat NPR-A due to the promiscuous nature of CNP in this species. Interesting, the DNP ...
Field studies were conducted May 28-June 1, 1979, to determine the chemical composition and physical behavior of discharges from an offshore gas drilling rig in the central basin of Lake Erie. The drilling operation was observed for four days, from rig jackup to the circulation of mud through the borehole after drilling had been completed. Resuspension studies using nephelometry, supplemented with chemical analyses, indicated little resuspension of lake bottom materials or release of metals to the water column during rig jack-up. Portions of the turbidity plumes generated during drilling were buoyant. Three surface turbidity plumes were mapped with nephelometry to a point at which particulate concentrations reached background levels in the Lake. Detectable plumes were approx. 400 to 1500 m in length and had maximum widths < 230 m. A chemical survey conducted in the plume during early gas shows indicated that discharged inorganic chemical species were rapidly ...
Full text: In the upper layers of the Earth's atmosphere, molecular nitrogen absorbs the extreme ultraviolet (XUV) solar radiation. The absorption is associated with dipole-allowed excitation of states of singlet ungerade symmetry ("1#SIGMA#"+_u and "1#PI#_u), which are known to undergo predissociation due to coupling with a mainfold of "1#PI#_u states. We determined new N_2 isotopic lifetimes of many "1#SIGMA#"+_u and "1#PI#_u states via line broadening measurements in the frequency domain. Ultrahigh resolution XUV + UV ionization spectra were recorded (bandwidth #approx# 250 MHz, resolving power 10"7), from which the natural linewidth, i.e. lifetime, was determined. These lifetimes provide new information about the predissociation of the singlet ungerade states in N_2. Tunable narrowband XUV radiation was produced by successively pulsed amplification of cw dye laser radiation, frequency doubling the pulsed visible laser beam into the UV and frequency tripling the ...
Among KEPCO's 9 nuclear power units, Korea Nuclear Unit No. 3, the Wolsung Nuclear Power Plant is the only CANDU-PHWR Unit, while the rest of 8 others are PWR units. The unit was designed by Atomic Energy of Canada, Ltd. of Canada, who also performed overall project management for the plant construction under the provisions and arrangement of the relevant contracts. The gross electrical output of the plant is 678.7 MWe and thermal output of the reactor is 2061 MWth. While these figures lead to lower plant efficiency than LWR counterparts, unit energy cost for fuel is more favorable than LWRs because natural uranium is utilized for the fuel bundles, some of which are already being fabricated domestically. Annual capacity factors for 1983 and 1984 could have been improved, if two major planned outages for the modification works on steam generator internals and one major forced outage from the heavy water spill incident could be ...
In Chapter 2 the evaluation methods of input ground motions for seismic design are summarized and especially the empirical and/or stochastic Green's function method is introduced in order to calculate the broadband strong motions based on the physically reliable fault model. Then the evaluation procedure is applied to the Ulsan fault system near which Wolsung nuclear power plant is located. In chapter3, the PSHA case studies for Wolsung NPP site are performed, in which multi attenuation equations of earthquake motions are adopted. Moreover, the results of seismic hazard evaluation for eight sites in Korea are shown. In addition, the contents of two literatures on seismic hazard evaluation are introduced. In chapter 4, isolation devices for emergency diesel generator have been studied. The models for friction-pendulum system, high damping rubber bearing and natural rubber bearing are developed and implemented in the TDAP-III. Then, the ...
11-MeV neutrons were elastically and inelastically scattered from eight single-closed-shell nuclei: three proton-vibrational nuclei with N = 50 ("8"8Sr, "9"0Zr, "9"2Mo) and five even-even neutron-vibrational nuclei ("1"1"6"-"1"2"4Sn) with Z = 50. Detection methods involving electronic discrimination against #gamma# rays, and time-of-flight techniques were used to measure the energy of the scattered neutrons. Data were taken from 15"0 to 150"0 in 5"0 intervals. Measured differential cross sections were normalized to the zero-degree neutron flux and corrected. An optical model (OM) analysis was used to fit the elastic data with the code GENOA, and potential parameters were obtained for each nucleus. The observed low-lying electric quadrupole (2"+) and octupole (3"-) states were collective in nature; the macroscopic or collective model for inelastic scattering was used to generate the differential cross-section angular distributions with the ...
Exposures from most natural and artificial sources, with the exception of those from medical radiology, are received at average dose rates of only a few microsieverts a day. Such risks as may be caused by these exposures are most unlikely to be determined with precision directly by epidemiological studies of populations exposed at these low rates. They may, however, be reliably inferred from the observed risks of exposure to rather larger doses delivered at higher dose rates in the light of the increasing knowledge of the phenomena involved in the initial cellular damage, the extent to which such damage is incorrectly repaired, and the processes which intervene between the genetic or other harm to cells and the likelihood of its final expression in inherited abnormality, in cancer development, or in defective foetal or embryonic growth. Current studies are of great importance, therefore, in examining the circumstances in which coding sections of the chromosomal DNA ...
Available in abstract form only. Full text of publication follows: The application spectrum of X-ray and Gamma radiation is increasing exponentially in the area of diagnostic, nuclear medicine, food preservation, nuclear power plants and strategic utilities. To prevent the harmful effects of these radiations, shielding materials based on lead metal and its compounds are being used historically, which are toxic in nature. To protect environment it has become necessary to develop non-toxic lead free shielding materials. The use of titanium metal and its compounds as synthetic rock i.e. SYNROC are reported to be very effective non-toxic shielding materials for various applications. Red mud waste generated in aluminum producing industries possesses a unique mineralogical compositions containing fairly high quantity of titanium oxide and iron oxide useful for making non toxic shielding compositions and therefore red mud has been utilized for the ...
A study was made for the purpose of electrification of unelectrified zones of the mountainous areas in developing countries using extremely small hydroelectric power facilities. The target for this project is a development of a micro hydroelectric power system with a size of about 5kW, which is estimated regarding that 1 village has 80 houses and each house needs electricity of 60W. In the study, the low-head system using a weir of irrigation channels in Subang pref. of West Java state was selected by the evaluation of access, stability of flow rate, natural conditions, etc. The hydroelectric power plant is of a flow-in method in which water is taken from the left bank and is injected/discharged to the downstream of the left bank. As the hybrid complementary power source, hybrid battery with a two-hour charging time at peak and a capacity of 3.5kWh was considered. When estimating the construction cost of the hybrid micro hydroelectric power system and equalizing by ...
At COP3 in 1997, an agreement was made to the innovative technical development/promotion by international cooperation, and the promotion of transfer of environmental technology to developing countries. Under the agreement, a feasibility study of international cooperation was made, and especially a study was conducted of the utilization/development of solar energy by the innovative solar thermochemical process. The main reason for global warming is emissions of a large amount of CO2 caused by the direct combustion of fossil fuels. Therefore, a CO2 recycle system taken up in the study enables a more substantial decline in CO2 emission (kg/kWh) per unit generation than the conventional thermal power system by composing solar methanol or solar dimethyl ether using fossil fuels including coal, water, CO2, etc. as raw materials and using solar energy as heat source, and by using this as fuel (solar fuel). CO2 can be reduced by 13% to 14% by substituting solar methanol or ...
Biomass is a potential source of energy that can reduce our dependency on oil as the main source of energy. In addition to municipal solid waste, animal and olive wastes are the main sources of organic waste in Jordan. In 2005, there were more than 2.4 million heads of sheep, about 72 thousand cows, and 40 million hens being raised in farms distributed in all governorates of Jordan. These animals produce 5.3 million tons (as exerted) of solid waste per year. If these quantities can be effectively collected they may constitute a valuable source of energy. This paper is aiming to estimate the amounts of animal and solid wastes generated in Jordan and their energy potential. The total amount of BOD from animal waste is estimated at 200,000 tons per year. Significant quantities of organic waste can also be collected from olive mills distributed in the country. This waste known locally as ''Jift'' is currently being collected and used ...
Electron cyclotron resonance heating (ECH) in BPX is planned as a possible upgrade to supplement the baseline ion cyclotron resonance frequency (ICRF) system. Eventual implementation primarily depends on the development of the required source technology. ECH offers important technical advantages over ICRF: High radio-frequency (FR) power density can be transmitted through ports (P/A >#approx# 100 MW/M"2), and the antenna need not be in contact with the plasma for efficient coupling. In particular, low-field side, linearly polarized (O-mode) power injection will suffice. By controlling the N spectrum, or by steering the antenna, the power deposition profile can be controlled during ramping of the magnetic field even with a fixed frequency source. Because of the possibility of localized power deposition, ECH is a natural candidate for controlling magnetrohydrodynamic (MHD) activity. Sawtooth oscillations may be prevented by heating in the vicinity of the q = 1 ...
Because of the chaotic nature of the corrosion process and the complexity of the electrochemical noise signals that are generated, there is no generally accepted method of measuring and interpreting these signals that allows the consistent detection and identification of sustained localized pitting (SLP) as compared to general corrosion. We have reexamined electrochemical noise analysis (ENA) of localized corrosion using different hardware, signal collection, and signal processing designs than those used in conventional ENA techniques. The new data acquisition system was designed to identify and monitor the progress of SLP by analyzing the power spectral density (PSD) of the trend of the corrosion current noise level (CNL) and potential noise level (PNL). Each CNL and PNL data point was calculated from the root-mean- square value of the ac components of current and potential fluctuation signals, which were measured simultaneously during a short ...
In the case where uranium recovered by an advanced aqueous reprocessing is utilized in light water reactors (LWRs) with the thermal neutron spectrum, the effects of the decontamination factor (DF) of the reprocessing on core neutronic characteristics were examined. The amounts of transuranium (TRU) elements and fission products (FPs) contained in the recovered uranium depend on the DF of reprocessing, and also "2"3"6U is generated by neutron capture of "2"3"5U during a reactor operation. These all act as poisons in the fuel. Therefore, in this paper, the additional "2"3"5U enrichment necessary to compensate for the produced TRU elements, FPs, and "2"3"6U was evaluated for three representative DF values: 10"2, 10"3, and infinity. The low value of 10"2 corresponds to the advanced aqueous reprocessing investigated here. An APWR core with a discharge burnup of 49 GWd/t when the initial "2"3"5U enrichment is 4.6% was considered as the reference core. Uranium of the ...
The Savannah River Site (SRS) is a 310-square-mile United States Department of Energy nuclear facility located along the Savannah River (SRS) near Aiken, South Carolina. Nuclear weapons material production began in the early 1950s, utilizing five production reactors. In the early 1990s all SRS production reactor operations were terminated. The first reactor closure end state declaration was recently institutionalized in a Comprehensive Environmental Response and Compensation and Liability Act (CERCLA) Early Action Record of Decision. The decision for the final closure of the 318,000 square foot 105-P Reactor was determined to be in situ decommissioning (ISD). ISD is an acceptable and cost effective alternative to off-site disposal for the reactor building, which will allow for consolidation of remedial action wastes generated from other cleanup activities within the P Area. ISD is considered protective by the regulators, U. S. Environmental Protection Agency (US ...
The TESLA Test Facility (TTF) at DESY is a facility producing sub-picosecond electron pulses for the generation of VUV or soft X-ray radiation in a free electron laser (FEL). The same electron pulses would also allow the direct production of high-power coherent radiation by passing the electron beam through an undulator. Intense, coherent far-infrared (FIR) undulator radiation can be produced from electron bunches at wavelengths longer than or equal to the bunch length. The source described in this paper provides, in the wavelength range 50-300 #mu#m, a train of about 1-10 ps long radiation pulses, with about 1 mJ of optical energy per pulse radiated into the central cone. The average output power can exceed 50 W. In this conceptual design, we intend to use a conventional electromagnetic undulator with a 60 cm period length and a maximum field of 1.5 T. The FIR source will use the spent electron beam coming from the VUV FEL which allows one to significantly extend ...
Three systems for the heat supply in the built environment have been compared for the costs, the energy consumption and emissions of CO{sub 2}, NO{sub x} and SO{sub 2}. The heating systems compared are based on central heating boilers, district heating systems in combination with combined steam and gas turbine cycles, and heating by means of several gas engines. From the results it appears that the boilers demand the lowest investments. The district heating systems are more expensive. Both heating systems, however, show considerable savings of energy (55 to 70%). The exploitation costs depend strongly on the fuel price scenarios used and the assumptions with regard to interest and inflation. The emissions of CO{sub 2} are also considerably lower for both combined heat and power generating systems. The use of gas engines results in higher acidifying emissions compared to the system with the central heating boilers, and lower acidifying emissions compared to the ...
The petroleum industry is increasing its focus on the exploration of reservoirs in turbidite systems. However, these sedimentary environments are often characterized by very complex sand distributions. Hence, reservoir description based on conventional seismic and well-log interpretation may be very uncertain. There is a need to employ more quantitative seismic techniques to reveal reservoirs units in these complex systems from seismic amplitude data. In this study we focus on North Sea turbidite systems. Our goal is to improve the ability to use 3D seismic data to map reservoirs in these systems. A cross-disciplinary methodology for seismic reservoir characterization is presented that combines rock physics, sedimentology, and statistical techniques. We apply this methodology to two turbidite systems of Paleocene age located in the South Viking Graben of the North Sea. First, we investigate the relationship between sedimentary petrography and rock physics properties. Next, we define ...
Feasibility of using combined release of sterile males and sterile females for population suppression of Earias vittella (Fabricius) was evaluated on okra in two ways. In one study, a combined release of sterile males and sterile females was evaluated under simulated conditions in laboratory, a 10: 10: 1: 1 (sterile male: sterile female: normal female: normal male) ratio effected > 99% sterility. In the second study, in a field cage experiment, a combined release of sterile males and sterile females was evaluated using normal males and tethered normal females. In this experiment, the release of sterile males and sterile females in 10: 10: 1: 1 ratio caused complete 'shut off' of mating of normal females for first 2 days and indicated>93% reduction in the larval progeny in the next generation. The tethered females were allowed to mate only once. E. vittella females mate multiply and so with overwhelming numbers of sterile males present, most probably the next ...
This article gives an account of the recent development of light water reactors new concepts in the world. Different projects are being studied. The CE80+ from Combustion Engineering (CE) is a 1350 MWe-PWR-type reactor whose primary circuit is confined in a spherical metallic containment. This reactor was certified by NRC (national regulatory commission) in mid-1996. The APWR (advanced pressurized water reactor) is developed by MHI (Mitsubishi heavy industries) in a collaboration with Westinghouse, this PWR-type reactor fitted with 4 loops derived from the SP90 model that was developed by Westinghouse during the eighties. 2 units of ABWR (advanced boiling water reactor) were commissioned in Japan in 1996 and 1997, ABWR was certified by NRC in mid-1996. The BWR90+ is developed by ABB-atom (Sweden) and it represents a cautious advanced version of the BWR75. Passive reactors are reactors that rely only on potential energy (compressed gas, gravitational flow or electric batteries) to feed ...
Analytical relations are obtained for estimating how the distributions of temperature and heat flux vary along a steam-generating tube and how the steam-generator power output reduces due to formation and accumulation of deposits.
Analytical relations are obtained for estimating how the distributions of temperature and heat flux vary along a steam-generating tube and how the steam-generator power output reduces due to formation and accumulation of deposits.
The effect of the water-chemical regime (WCR) on damage sustained by heating surfaces of steam generators at NPP is analyzed. It is indicated that phosphate treatment with minimal excesses of phosphates in the steamgenerator water is the most optimal method of managing the WCR regime of horizontal steam generators.
1. Nitric oxide generation is important in the regulation of resistance vessel tone. Until now, however, there has been no evidence of such a role for basal generation of nitric oxide in the skin microcirculation...Full Text Available
IntroductionThe aim of the study was to assess and classify incidents of electromagnetic interference (EMI) by second-generation and third-generation mobile phones on critical care...Full Text Available
Statistical data on experience gained from operation of steam generators around the world are presented, problems arising in vertical and horizontal steam generators are described, and the conditions of heattransfer tubes used in them are compared.
Results are described of a study and of the characteristics of sources of a non-equilibrium gas-discharge plasma. The plasma generators considered include glow, high frequency, and arc discharge generators. Thermodynamic, ionic, and electronic processes occurring in the plasmas are evaluated.
The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main to...
The main problems encountered during the operation of horizontal steam generators are considered. Design features of the new PGV-1000MK and PGV-1500 steam generators are analyzed.
A series of tests were completed at the Fast Flux Test Facility to demonstrate the passive safety characteristics of liquid metal reactors with natural circulation flow. The first test consisted of transition from forced to natural circulation flow at an initial decay power of 0.3%. The second test represented an unprotected loss-of-flow transient to natural circulation from 50% power with the control rods prevented from scramming into the core. The third test was a steady-state, natural circulation condition with core fission powers up ato about 2.3%. Core sodium data and results of single and multi-channel computer models confirmed the reliability and effectiveness of natural circulation flow for liquid metal reactor safety.
Some aspects of the PSO scheme for natural gas are examined critically. Two central arguments used for justifying the PSO subsidy scheme of natural gas and its distribution are reviewed; these include the 'smallholder argument' and the 'environmental argument'. The 'smallholder argument' claims that since Norway has the natural gas resources, it should also make use of the natural gas in the country, and not simply send the raw material to other countries. The 'environmental argument' states that natural gas compared to other fossil fuels such as coal and fuel oil, is a far cleaner alternative, thus an environmental-friendly alternative entitled to financial support. The arguments are critically examined by the author (ml)
Natural gas is a promising alternative fuel to meet strict engine emission regulations in many countries. Natural gas engines can operate at lean burn and stoichiometric conditions with different combustion and emission characteristics. In this paper, the operating envelope, fuel economy, emissions, cycle-to-cycle variations in indicated mean effective pressure and strategies to achieve stable combustion of lean burn natural gas engines are highlighted. Stoichiometric natural gas engines are briefly reviewed. To keep the output power and torque of natural gas engines comparable to those of their gasoline or Diesel counterparts, high boost pressure should be used. High activity catalyst for methane oxidation and lean deNOx system or three way catalyst with precise air-fuel ratio control str...
The use of Funtumia latex and nitrobenzene as molecular weight depressants for natural rubber was studied. Portions of a given sample of natural rubber latex were treated with these materials, and this provided a means of ascertaining the amount of Funtumia latex in a blend with natural rubber that could produce a lowering of the molecular weight equivalent to that from known concentrations of nitrobenzene in natural rubber latex. The molecular weight of the products decreased to an equilibrium value after 10 h of reaction with nitrobenzene. The calculations revealed that a 27.9% substitution of natural rubber latex (300 mL) with Funtumia rubber latex achieved the same result as nitrobenzene in the same polymer at concentrations of 0.5-2.0 wt % of the dry rubber content of the latex after ...
The buoyancy driven convective flow fields are steady circulatory flows which were made between surfaces maintained at two fixed temperatures. They are ubiquitous in nature and play an important role in many engineering applications. Especially, in last decades, natural convection in a close loop or cavity becomes the main issue in the molecular biology for the polymerase chain reaction (PCR). Application of a natural convection can reduce the costs and efforts remarkably. This paper focuses on the sensitivity study of turbulence analysis using CFD for a natural convection in a closed rectangular cavity. Using commercial CFD code, FLUENT, various turbulent models were applied to the turbulent flow. Results from each CFD model will be compared each other in the viewpoints of flow characteristics. This work will suggest the best turbulent model of CFD for analyzing turbulent flows of the ...
The buoyancy driven convective flow fields are steady circulatory flows which were made between surfaces maintained at two fixed temperatures. They are ubiquitous in nature and play an important role in many engineering applications. Especially, in last decades, natural convection in a close loop or cavity becomes the main issue in the molecular biology for the polymerase chain reaction (PCR). Application of a natural convection can reduce the costs and efforts remarkably. This paper focuses on the sensitivity study of turbulence analysis using CFD for a natural convection in a closed rectangular cavity. Using commercial CFD code, FLUENT, various turbulent models were applied to the turbulent flow. Results from each CFD model will be compared each other in the viewpoints of flow characteristics. This work will suggest the best turbulent model of CFD for analyzing turbulent flows of the ...
The thermal-hydraulic tests for a horizontal steam generator of a next-generation PWR (New PWR-21) were performed. The purpose of these tests is to understand the thermal-hydraulic behavior in the secondary side of horizontal steam generator during the plant normal operation. A test was carried out with cross section slice model simulated the straight tube region. In this paper, the results of the test is reported, and the effect of the horizontal steam generator internals on the thermal-hydraulic behavior of the secondary side and the circulation characteristics of the secondary side are discussed. (author)
The thermal-hydraulic tests for a horizontal steam generator of a next-generation PWR (New PWR-21) were performed. The purpose of these tests is to understand the thermal-hydraulic behavior in the secondary side of horizontal steam generator during the plant normal operation. A test was carried out with cross section slice model simulated the straight tube region. In this paper, the results of the test is reported, and the effect of the horizontal steam generator internals on the thermal-hydraulic behavior of the secondary side and the circulation characteristics of the secondary side are discussed. (author).
Finland has some 10 million hectares of peatland, accounting for almost a third of its total area. Macroclimatic conditions have varied in the course of the Holocene growth and development of this peatland, and with them the habitats of the peat-forming plants. Temperatures and moisture conditions have played a significant role in determining the dominant species of mire plants growing there at any particular time, the resulting mire types and the accumulation and deposition of plant remains to form the peat. While in a natural state the mires of Finland have functioned as carbon dioxide sinks throughout the post-glacial period, but the ditching of peatland for forestry and agriculture, amounting to some 5,7 million hectares in Finland, has affected their water balance, especially over the last hundred years, and has thereby altered the quantity and species composition of the mire vegetation. The invasion of trees and woody plants to replace the typical mire plants ...
... of waste food generated at McMurdo Station. Some of the difficulties of disposing of waste food ... change waste generation or management at the site? Yes. This will be a temporary waste management ...
We investigate the solar neutrino problem in the scenario of three generation neutrino oscillation hypothesis, taking into account other phenomenological constraints to the neutrino mixing and mass parameters.
This perspective view of Venus, generated by computer from NASA's Magellan data and color-coded with emissivity, shows part of the lowlands to the north of ...
This dissertation is devoted to the study of the phenomenological consequences of the three-generation heterotic string models based on the Calabi-Yau compactifications and the N = 2 superconformal constructions.
This paper describes the construction of PWR horizontal steam generator in Soviet Union, the water chemistry treatment for secondary side, the design of steam separator, the test of heat transfer characteristics and operation. (author).
Network generators that capture the Internet's large-scale topology are crucial for the development of efficient routing protocols and modeling Internet traffic. Our ability to design realistic generators...Full Text Available
The results obtained from experimental investigations and mathematical simulation of horizontal steam generators are considered. Recommendations for continuing these works are given.
This paper presents a new method and newly developed stabilizing equipment to prevent the loss of synchronism of generators in pumped-storage plants from spreading. The proposed method includes functions to estimate the swing of each generator by using on-line generator output sampled at a rate of 600 times per second after an occurrence of disturbance such as fault, faulty equipment and so on, to predict generator swing 200-300 milliseconds ahead and loss of synchronism between generators in pumped-storage plants and those in thermal and nuclear plants, and to decide the number of generators that must be shed to maintain stability. Tokyo Electric Power Co. (TEPCO) installed the newly developed stabilizing equipment based on this method in the power system in June, 1986.
This paper presents a new method and newly developed stabilizing equipment to prevent the loss of synchronism of generators in pumped-storage plants from spreading. The proposed method includes functions to estimate the swing of each generator by using on-line generator output sampled at a rate of 600 times per second after an occurrence of disturbance such as fault, faulty equipment and so on, to predict generator swing 200-300 milliseconds ahead and loss of synchronism between generators in pumped-storage plants and those in thermal and nuclear plants, and to decide the number of generators that must be shed to maintain stability. Tokyo Electric Power Co. (TEPCO) installed the newly developed stabilizing equipment based on this method in the power system in June, 1986.
Additional measurements have been made of deposition and retention of inhaled radioactively labeled iron oxide aerosols generated by a spinning top aerosol generator.
Several proposals have been made on the method of calculating generation of formaldehyde released from plywood. In calculating generation per hour of a volatile organic compound of adhesives or coatings using a chamber method, such models are frequently used that the generation is largest when the specimen is exposed in the chamber and that the generation attenuates with lapse of time. In the meantime, a number of studies for calculating formaldehyde generation from construction materials are often those determining a specific quantity of generation in a stationary state, while few studies are the observation of time series variation from immediately after the exposure into the chamber. Accordingly, the subject studies used lauan plywood as the samples and examined the method of calculating the change with lapse of time of the formaldehyde ...
The natural gas industry has proposed an increase in the DOE gas R&D budget from about $100 million to about $250 million per year for each of the next 10 years. The proposal includes four programs: natural gas supplies, fuel cells, natural gas vehicles and stationary combustion systems. This paper is a qualitative assessment of the gas industry proposal and recommends a natural gas R&D strategy for the DOE. The methodology is a conceptual framework based on an analysis of market failures and the energy policy objectives of the DOE`s (1991) National Energy Strategy. This framework would assist the DOE in constructing an R&D portfolio that achieves energy policy objectives. The natural gas supply program is recommended to the extent that it contributes to energy price stability. Stationary combustion programs are supported on grounds of economic efficiency and ...
1. l(+)-Methionine sulphoxide has been isolated for the first time from a natural source, the blowfly Phormia regina. 2. The natural compound is shown to be identical with...Full Text Available
A survey is given on the results in hand on the natural radioactivity of building materials. It is shown that only a small percentage of building materials has an increased content of radioactive materials. The results are compared with approximate values given in a Russian publication. (orig./AK).
BackgroundNaturally acquired immune responses against sexual stages of P. falciparum can reduce the transmission of malaria from humans to mosquitoes. These antigens...Full Text Available
Although genetic engineering techniques for baker's yeast might improve the yeast's fermentation characteristics, the lack of scientific data on the survival of such strains in natural environments...Full Text Available
SUMMARYThe cytolytic activity of natural killer (NK) cells is regulated by inhibitory receptors that detect the absence of self molecules on target cells. Structural studies of...Full Text Available
Natural resources in general and plant materials in particular are receiving more attention due to their safety as pharmaceutical excipients. Present work assessed the potential of a natural polysaccharide,...Full Text Available
Research on the feasibility of growing cattails as an energy crop is described. The following topics are included: productivity in natural strands, germination requirements for seed, establishing stands by seeding, rhizome dormancy and development, harvesting and stand establishment, and analysis of canopy structure and radiation profiles in a natural community. (MHR)
This article puts the case for coal fired combined cycle gas turbine (CCGT) power plants. The need to gasify the coal for the CCGT, use of fluidised bed combustors or gasification systems, the difference in prices of coal and natural gas, and coal and natural gas reserves are discussed. (UK)
The amended Radiation Protection Ordinance of 2001 contains regulations on natural radioactive materials, whose recycling or disposal poses practical problems. There is little experience in this field so far.
Naturally occurring, double-stranded RNA (ds-RNA)) was immunogenic when injected into mice, rats, guinea-pigs, rabbits, dogs and baboons. The response to native material administered intravenously (i.v.)...Full Text Available
Petroleum is the unchallenged energy market leader in West Germany,having a share of 42%; natural gas accounts for 16-17%. West Germany imports 29% of its natural gas from the Soviet Union, 28% from the Netherlands, 14% from Norway, and 1% from Denmark. In West Germany many-branched natural gas distribution system is operated, equipped with a.o. 21 installations for underground storage which results in a great flexibility of the system. Because of the preferential treatment given to the use of coal as fuel for power plants the share of natural gas has decreased to the present 6% in the last ten years. In the indutrial sector the share is 18%. Strict air pollution abatement measures ('TA-Luft') favour the use of natural gas. However, duty has been levied on the use of natural gas per January 1st, 1989. For space heating of houses and commercial ...
This document is a synthesis of data and analysis concerning natural circulation cooling in US Pressurized Water Reactors during off-normal operation and accident transients. Its objective is the integration of important research findings concerning PWR natural circulation phenomena into a single reference document. Sources of information include the Nuclear Regulatory Commission, reactor vendors, utility sponsored research groups, utilities, national laboratories, research reports, meeting papers, archival literature, and foreign sources. Three modes of natural circulation are discussed: single-phase, two-phase, and reflux/boiling condensation. General characteristics, analytical expressions, noncondensible gas effects, secondary effects, and nonuniform flow are described with regard to each of the natural circulation modes. Plant operational data, tests in scaled experimental facilities, and analysis ...
The physicochemical nature of a silicoaluminophosphate with the faujasite structure has been studied. The molecular sieve framework contains a homogeneous distribution of silicon, aluminum, and phosphorus and is negatively charged. Combustion in air of the charge-compensating organic cations produces hydroxyl groups which exhibit Broensted acidity.
Legal aspects of using natural gas as boiler fuel for electric utilities are reviewed through one utility's challenges to the Power Plant and Industrial Fuel Use implementation. ASARCO vs. FPC, 1973, and City of Willcox vs. FPC are discussed. (PSB)
Naturally acquired immunity to Plasmodium falciparum malaria in malaria holoendemic areas is characterized by the gradual, age-related development of protection against high-density...Full Text Available
Understanding the detailed mechanics of these systems and their place in the general picture of binary star evolution are the dual objectives of this ...
... due to the evolving nature of the Strategy Maps and the changing priority roles, it was decided not to link the SMSP directly with any Strategic Plans. ...
Laboratory research data is used as the basis for recommendations to be used in selecting a modification regime employing the treatment of clinoptilolite with NS1 to remove mercaptans from natural gas. The dynamic activity of the modified clinoptilolite is seven times greater than the activity of nontreated material.
This report revises estimates of population exposure to external natural background made by D. T. Oakley in 1972. The revisions include more recent estimates of dose equivalents from cosmic rays, use of 1970 U.S. census data, and corrections for building shielding and for self-shielding in the body. The dose equivalents calculated are those from cosmic rays and terrestrial radiation, and do not include doses from natural radioactive materials in the body.
Natural radioactivity of rocks is studied on the basis of core samples and radioactivity logs of marine deposits in Azerbaijan. Investigations have established mainly thorium-potassium nature of radioactivity. Data obtained are useful for identificafion of clay among other rocks, for determination of clayiness, and in presence of a corresponding relation - for determination of porosity according to the clayiness. It is shown that the clayiness may be determined from radioactive logs.
This thesis study covers both global performance and local phenomena analyses focusing on natural circulation reactor design safety. Four important topics are included: the global SBWR design safety assessment, important local phenomena investigation, steady and transient natural circulation process study, and two-phase instability analysis. The conceptual design of the SBWR-200 is introduced in this thesis and the global performance of a natural circulation reactor is then assessed using PUMA integral test data and RELAP5 simulations. A safety assessment methodology is developed to evaluate the PUMA integral test data extrapolation and code scalability. The RELAP5 code simulation capability in low-pressure low-flow conditions is also validated. The study shows that the code is capable of predicting the global accident scenario in natural circulation reactors with reasonable accuracy, while failing to ...
An AHR (Advanced HANARO Reactor) based on the HANARO has been conceptually developed for the future needs of research reactors. Generally, a natural convection cooling in nuclear installations is an ultimate heat removal mechanism as an inherent safety feature. This paper presents the preliminary thermal hydraulic characteristics and safety margins for a natural convection cooling in the AHR.
Horizontal steam generators are typical parts of nuclear power plants with pressure water reactor type VVER. By means of this computer program, a detailed thermal-hydraulic study of the horizontal steam generator PGV-1000 has been carried out and a special attention has been paid to the thermal-hydraulics of the secondary side. A set of important steam generator characteristics has been obtained and analyzed. Some of the interesting results of the analysis are presented in the paper. (author)
The principal types of corrosion are presented which can occur in CANDU steam generator. There are also presented the operation conditions, the specifications referring to the water chemistry and the construction materials of Steam Generator, the factors that have a great influence on the corrosion behaviour during the whole exploitation period of this equipment. The most important elements of CANDU Steam Generator ageing management program are also discussed. (R. P.)
A survey was conducted of experience with steam generator tubes at nuclear power stations during 1976. Failures were reported at 25 out of 68 water-cooled reactors. The causes of these failures and the repair and inspection procedures designed to cope with them are summarized. Examination of the data indicates that corrosion was the major cause of steam generator tube failures. Improvements are needed in steam generator design, condenser integrity and secondary water chemistry control. (author).
Peculiarities of design of the PGV-1000 horizontal steam generator affecting soluble impurity distribution in its water volume are considered in brief. The results of estimating sodium distribution in different zones of the steam generator are presented. The conclusion is made on the necessity of arrangement of representative measurements of sodium and chloride content in water volume of the steam generator, particularly, in the hot bottom zone for optimization of blow-through flowsheet and its regulations.
Results are given of numerical simulation of three-dimensional pattern of flow of a two-phase steam-water mixture in the house of a PGV-1000 horizontal steam generator obtained using the BAGIRA best-estimate thermohydrodynamic computer codes. The space distributions of velocities and local void fractions in the steam generator housing for different modes of operation of power-generating unit are calculated and compared with available experimental data.
Results are given of numerical simulation of three-dimensional pattern of flow of a two-phase steam-water mixture in the house of a PGV-1000 horizontal steam generator obtained using the BAGIRA best-estimate thermohydrodynamic computer codes. The space distributions of velocities and local void fractions in the steam generator housing for different modes of operation of power-generating unit are calculated and compared with available experimental data.
... Three prototype reactors were constructed and the photocatalysts used were TiO2 for hydroxyl radical generation, dyes such as methylene blue and rose bengal for singlet oxygen generation, and ferric chloride/hydrogen peroxide in Photo-Fenton OH radical generation. Singlet oxygen was effective against some of the pesticides but reacted slowly or not at all with others. All pesticides were degraded by OH radical generating agents (such as methylene blue)...
This paper will describe the application of power generation by the use of microturbine technology by Capstone Turbine Corporation throughout South America. The purpose of this paper is to describe the technology and the experience gained over the last six years. The microturbines are power generation systems that produce energy from a diverse range of liquid or gaseous fuels. The generator is driven by a small gas turbine with a common shaft for the rotors of the generator and the engine. (author)
Superconducting generators for high power applications have been of interest for a number of years. Superconducting generators using low temperature superconductors (LTS) have been manufactured to produce up to 20 MW of electrical power and have been configured in either synchronous alternators which have an AC output that may be subsequently rectified to produce DC and homopolar generators which produce low voltage DC. Typically these generators require scrupulous attention to vacuum integrity for cryogenic insulation at 4.2K and tend to be somewhat fragile because of extensive thermal and magnetic shields that are not required in conventional power generators. Recently, high purity aluminum composites have been developed for a high power AC generator that is cooled by cryogenic hydrogen at 21K. This aluminum generator is very compact and ...
The objective of this study was to identify and assess the present and future dimensions of environmental effects and impacts of various energy generation alternatives, and to place safety and environmental risks associated with the nuclear industry in Canada in perspective with the risks from other sources. It was found that nuclear power generation involves a comparable risk to that of conventional methods of thermoelectric power generation.
This paper deals with dynamic study of co-generator system with derived dynamic models of generator, excitation system, and turbine/governor from field tests. Mainly this study concentrates on frequency control by under-frequency relay. We simulates dynamic study of co-generator system using EMTDC. (author). 4 refs., 13 figs., 4 tabs.
Implementation of a plan to charge waste management costs to the facility that generates such waste requires a long-term commitment and consistent administration. The benefit is that generators are provided the incentive to optimize waste management practices if the charges are appropriately applied. This paper summarizes (1) a plan to charge waste generators, (2) the administrative structure of the plan, (3) a comparison between the rate structure and changes in waste disposal operations, and (4) issues that have surfaced as the plan is implemented. 2 refs., 1 fig., 1 tab.
Ways of improving the water chemistry used in the turbine generator stator?s cooling systems at Russian nuclear power plants are considered. Data obtained from operational chemical monitoring of indicators characterizing the quality of cooling water in the turbine generator stator cooling systems of operating power units at nuclear power plants are presented.
Carbon capture and storage have been receiving increasing interest lately, mainly as an option to reduce CO{sub 2} emissions from the power sector. The concept could be adapted for production of H{sub 2} as well, which would provide a carbon free energy carrier that could be used for example as transportation fuel. In this doctoral thesis, the option to use chemical-looping technologies to produce H{sub 2} from fossil fuels with CO{sub 2} capture is explored. In chemical-looping combustion, direct contact between fuel and combustion air is avoided. Instead, a solid oxygen carrier performs the task of bringing oxygen from the air to the fuel. Thus, the resulting CO{sub 2} and H{sub 2}O are not diluted with N{sub 2}, and pure CO{sub 2} can easily be recovered by cooling and condensation. The heat of reaction is the same as for ordinary combustion. Chemical-looping reforming uses the same basic principles as chemical-looping combustion, but operates at under stoichiometric conditions. ...
A robust fusion of the agricultural, industrial biotechnology, and energy industries can create a new strategic national capability for energy independence and climate protection. In his State of the Union Address (Bush 2006), President George W. Bush outlined the Advanced Energy Initiative, which seeks to reduce our national dependence on imported oil by accelerating the development of domestic, renewable alternatives to gasoline and diesel fuels. The president has set a national goal of developing cleaner, cheaper, and more reliable alternative energy sources to substantially replace oil imports in the coming years. Fuels derived from cellulosic biomass - the fibrous, woody, and generally inedible portions of plant matter - offer one such alternative to conventional energy sources that can dramatically impact national economic growth, national energy security, and environmental goals. Cellulosic biomass is an attractive energy feedstock because it is an abundant, domestic, renewable ...
The paper analyses the advantages and disadvantages of the second generation improved technologies and third generation technologies mainly developed in China in terms of safety and economy. The paper also discusses the maturity of the second generation improved technologies and the sophistication of the third generation technologies respectively. Meanwhile, the paper proposes that the advantage and disadvantage of second generation improved technologies and third generation technologies should be carefully taken into consideration and the relationship between the maturity and sophistication should be properly dealt with in the current stage. A two-step strategy shall be taken as a solution to solve the problem of insufficient capacity of nuclear power, trace and develop the third generation technologies, so as to ensure the sound and fast ...
The Steam Generator (SG) tubing degradation caused by corrosion and other age-related mechanisms continues to be a significant safety and cost concern for many Nuclear Power Plants (NPP). The understanding of the steam generator ageing mechanisms is the key to effective management of steam generator ageing and consists of the knowledge of steam generator materials and these one properties, stressors and operating conditions, like degradation sites and wear mechanisms. The principal types of corrosion are presented which can occur in CANDU steam generator. There are also presented the operation conditions, the specifications referring to the water chemistry and the construction materials of Steam Generator, the factors that have a great influence on the corrosion behaviour during the whole exploitation period of this equipment. (R.P.)
The steam generator is a very important component of a nuclear power plant. Historically, vertical steam generators came to be used abroad and horizontal steam generators in our country. Both types of steam generators operate successfully in nuclear power plants and satisfactorily fulfill their functions, enabling the production of electricity. Repeated attempts to re-examine the existing concepts in one or another country have been unsuccessful because there are no convincing arguments for this. Nonetheless, the question of using a different type of steam generator is raised periodically in our country and abroad. This article briefly reviews different concepts of steam generators. Their parameters, characteristics, and thermal efficiency are compared and ways to increase the latter are a...
This article describes the project for the installation of an additional emergency diesel generator in both Asco and Vandellos NPPs. The basic objectives of this project are to improve the availability of the emergency generation system, in order to provide greater ability to address potential contingencies, and also to increase the flexibility of the preventive periodic maintenance of the emergency diesel generators. This maintenance, that is currently a milestone of the critical path of the refueling outage, will be performed on-line. The new diesel generator will be sized to support all the loads considered in the safety case and also the consumption of its own auxiliary systems, and will be tested for operability assessment on the same periodical basis than the existing ones. The solution adopted will also permit that the N diesel generator may be connected to any bus bar class ...
In the current wind turbine generation system, there are substantial problems such as the maximum power of the wind turbine cannot be obtained under the fluctuating wind speed, high in cost and low in annual net electricity production (due to mismatch between a generator and a wind turbine). A new wind turbine generator optimized for the wind turbine output is presented in order to solve such problems. This wind turbine generator consists of a permanent magnet generator, a reactor and a rectifier, and uses neither a control circuit which requires standby electricity nor a PWM converter having a switching element. By selecting most appropriate combination of the permanent magnet generator having multiple windings and the reactor connected in series with each winding, the maximum output of the wind turbine can be obtained without using a control circuit. The new ...
Turkey's natural gas (NG) production is very small and is almost all imported. Turkish natural gas production in 2000, 23 billion cubic feet (Bcf), met around 4% of domestic natural gas consumption requirements. NG consumption is estimated at around 700 Bcf in year 2002, accounting for around 17% of Turkey's total energy consumption. Turkish natural gas demand had been projected to increase extremely rapidly in coming years. Country oil production is 50,674 barrels per day (bbl/d) of which 46,674 bbl/d was crude oil in 2002. In 2002, oil consumption was 635,000 bbl/d and net oil imports was 584,326 bbl/d in Turkey. Oil provides around 43% of Turkey's total energy requirements. (Author)
In this paper, the authors investigate the technical and economical aspects of the natural gas injection in non-integrated pig-iron plants using charcoal in the blast furnace. The effects of the natural gas injection concerning the blast furnace flame temperature, charcoal consumption, productively and permeability are analyzed. It was found that the injection is beneficial in many ways, such as in the improvement of the productivity and quality, if the flame temperature is kept within an appropriate range. In the financial-economic project`s evaluation, the cash flow for the natural gas injection was analysed considering two blast conditions: through the drying and oxygen enrichment of the air. A sensibility analysis is presented in which the internal rate of return of the investment varies according to the prices of charcoal and oxygen. 3 refs., 3 figs., 3 tabs
The majority of Brazilian big cities served by conventional railroad systems with routes starting in the center of the URBIS, destinate them the long distances transport of passengers and cargo. Actually, these systems are being transformed to become commuter trains which join a great capacity of transportation to a much lower costs of implantation than subway ones. The most important characteristic of this train, when talking about energy consumption, is the possibility of using different kinds of explosion engines from three cycles: Diesel, mixed (Diesel + Natural Gas), and Otto moved by natural gas, besides the traditional electric traction. The use of natural gas in Otto cycle engines shows itself competitive from the point of view of investments, operational costs and environmental preservation. (author). 10 refs., 1 fig
One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases. 5 refs., 9 figs., 1 tab.
Experimental investigations have been conducted to determine two-phase natural circulation interfacial parameters by real-time neutron radiography. The natural circulation loop used in the present experiments consists of a vertical two-phase section, a gas liquid separator, and a gas injection/heating section. Experiments were performed in a neutron beam for visualization using realtime neutron radiography system. The natural circulation was initiated by injection of known gas flow rate in the heated section. Two-phase flow interfacial parameters including interfacial geometry and phase velocities etc. for bubbly flow and slug flow patterns observed in the experiments will be given in detail. The results indicate that while the natural circulation is largely as expected and that steady stable flows are possible, there are some local phenomena that introduce instabilities due to the interfacial phenomena ...
Experimental investigations have been conducted to determine two-phase natural circulation interfacial parameters by real-time neutron radiography. The natural circulation loop used in the present experiments consists of a vertical two-phase section, a gas liquid separator, and a gas injection/heating section. Experiments were performed in a neutron beam for visualization using realtime neutron radiography system. The natural circulation was initiated by injection of known gas flow rate in the heated section. Two-phase flow interfacial parameters including interfacial geometry and phase velocities etc. for bubbly flow and slug flow patterns observed in the experiments will be given in detail. The results indicate that while the natural circulation is largely as expected and that steady stable flows are possible, there are some local phenomena that introduce instabilities due to the interfacial phenomena ...
The Granger instantaneous-causality test is applied to explore the potential causal relationships between wholesale electricity and natural-gas prices in California. The test shows these relationships to be bi-directional, and reveals California's electricity and natural-gas markets to be as inextricably intertwined as casual observation and theoretical considerations would suggest they ought to be. This meshing of markets exacerbated the effects of California's natural-gas crisis on the contemporaneous electricity crisis, while concurrently the electricity crisis may have contributed to the dysfunction in the national-gas market and helped to precipitate the natural-gas crisis. The finding supports an integrated approach, as opposed to a piecemeal approach, for formulating energy policy recommendations, not just in California but in the world at large. (author)
The Granger instantaneous-causality test is applied to explore the potential causal relationships between wholesale electricity and natural-gas prices in California. The test shows these relationships to be bi-directional, and reveals California's electricity and natural-gas markets to be as inextricably intertwined as casual observation and theoretical considerations would suggest they ought to be. This meshing of markets exacerbated the effects of California's natural-gas crisis on the contemporaneous electricity crisis, while concurrently the electricity crisis may have contributed to the dysfunction in the national-gas market and helped to precipitate the natural-gas crisis. The finding supports an integrated approach, as opposed to a piecemeal approach, for formulating energy policy recommendations, not just in California but in the world at large.
The Stefan problem involving a source term is considered in this technical note. As an example, planar solidification with time-dependent heat generation in a semi-infinite plane is solved by use of a perturbation technique. The perturbation solution is validated by reducing the problem to the case without heat generation whose exact solution is available. An application to the case with constant heat generation is presented, for which a closed-form solution is obtained. The effects of heat generation and Stefan number on the evolution of solidification are examined using the perturbation solution.
A method of detecting explosives in a vehicle includes providing a first rack on one side of the vehicle, the rack including a neutron generator and a plurality of gamma ray detectors; providing a second rack on another side of the vehicle, the second rack including a neutron generator and a plurality of gamma ray detectors; providing a control system, remote from the first and second racks, coupled to the neutron generators and gamma ray detectors; using the control system, causing the neutron generators to generate neutrons; and performing gamma ray spectroscopy on spectra read by the gamma ray detectors to look for a signature indicative of presence of an explosive. Various apparatus and other methods are also provided.
Purpose: In a case of automatically controlling the water level at the time of generating a lower power, to impact the followability of the control necessary for the power variation of the steam generator thereby to obtain good controllability. Constitution: A signal of deviation of water level of a steam generator and its set value and a signal of a difference between the temperature of the primary coolant in the high temperature side pipeline and that of the primary coolant in the low temperature side pipeline are used to automatically or manually control the flow quantity of water fed to the steam generator. (Yoshihara, H.).
A method of detecting explosives in a vehicle includes providing a first rack on one side of the vehicle, the rack including a neutron generator and a plurality of gamma ray detectors; providing a second rack on another side of the vehicle, the second rack including a neutron generator and a plurality of gamma ray detectors; providing a control system, remote from the first and second racks, coupled to the neutron generators and gamma ray detectors; using the control system, causing the neutron generators to generate neutrons; and performing gamma ray spectroscopy on spectra read by the gamma ray detectors to look for a signature indicative of presence of an explosive. Various apparatus and other methods are also provided.
There are several concerns which bring to consider natural gas as a viable alternative to liquid fuels in transport. First, natural gas allows the curbing of global pollution in this steadily growing industry. Indeed, decoupling greenhouse gas emissions from transport growth has become a major issue in tackling climate change. Second, a more extensive use of natural gas would relieve city air quality, which is presently at levels harmful of human health. Nonetheless, this is just one side of the coin. The other side entails building a refuelling station network, and this carries financial requirements. The financing fraction holds a pivotal role in deciding whether natural gas for automotive purposes is an efficient solution. The final aim of this work is, therefore, to compare the natural gas advantages, stemming from avoided global and local emission, with the economic rationale ...
This study develops a statistical model of industrial US natural gas consumption based upon historical data for the 1958-2003 period. The model specifically addresses interfuel substitution possibilities and changes in the industrial economic base. Using a relatively simple approach, the framework can be simulated repeatedly with little effort over a range of different conditions. It may also provide a valuable input into larger modeling exercises where an organization wants to determine long-run natural gas prices based upon supply and demand conditions. Projections based upon this demand framework indicate that industrial natural gas consumption may grow more slowly over the next 20 yr than being projected by the U.S. Energy Information Administration (EIA). This conclusion is based upon the assumption that natural gas prices will follow oil prices, as they have done over recent decades. If ...
The increasing price differential between natural gas and coal will create a demand for technology that can allow the displacement of natural gas with coal in power plants. Coal gasification is the standard approach suggested to allow coal to displace natural gas. However, the relatively high capital investment required for coal gasification will require fuel cost differentials higher than those anticipated in the near term before coal gasification replaces natural gas. One way of achieving shorter term displacement of natural gas by coal would be to develop technology that would allow coal to be used as the heat source for the endothermic reforming of natural gas. In a natural gas-fired combined cycle power plant, the endothermic heat of reforming, which would be provided by coal combustion, is recovered in the combined-cycle. Therefore, ...
High and volatile natural gas prices have increasingly led to calls for investments in renewable energy. One line of argument is that deployment of these resources may lead to reductions in the demand for and price of natural gas. Many recent US-based modeling studies have demonstrated that this effect could provide significant consumer savings. In this article we evaluate these studies, and benchmark their findings against economic theory, other modeling results, and a limited empirical literature. We find that many uncertainties remain regarding the absolute magnitude of this effect, and that the reduction in natural gas prices may not represent an increase in aggregate economic wealth. Nonetheless, we conclude that many of the studies of the impact of renewable energy on natural gas prices appear to have represented this effect within reason, given current knowledge. These studies specifically ...
High and volatile natural gas prices have increasingly led to calls for investments in renewable energy. One line of argument is that deployment of these resources may lead to reductions in the demand for and price of natural gas. Many recent US-based modeling studies have demonstrated that this effect could provide significant consumer savings. In this article we evaluate these studies, and benchmark their findings against economic theory, other modeling results, and a limited empirical literature. We find that many uncertainties remain regarding the absolute magnitude of this effect, and that the reduction in natural gas prices may not represent an increase in aggregate economic wealth. Nonetheless, we conclude that many of the studies of the impact of renewable energy on natural gas prices appear to have represented this effect within reason, given current knowledge. These studies specifically ...
Full text: As you know, thin films which generate anomalous big photovoltage (APhV) , as film photo resistive structures made of the combinations of A_2B_6 respond to X-ray and #gamma#- radiations. In this work the influence of X-ray and #gamma#-radiations on the quantity of APhV in the system APhV-film-photoresistor was investigated. Earlier polycrystal films with anomalous photo voltage properties were received only on the clean and flat surface with high isolation property (R>10"1"4 #OMEGA#). We worked out the technology of receiving APhV films CdTe on the surface of the photosensitive film CdS. The main condition under which this effect may be observed is that the lining must be slant concerning to the direction of the motion of evaporated substance's molecular bunch during the growing of the film, i.e. received film must have a dendritic structure. That is why photosensitive film CdS was received with thermo vacuum slanting pulverization (#alpha#=30-60 ...
H{sub 2}Gen, with the support of the Department of Energy, successfully designed, built and field-tested two steam methane reformers with 578 kg/day capacity, which has now become a standard commercial product serving customers in the specialty metals and PV manufacturing businesses. We demonstrated that this reformer/PSA system, when combined with compression, storage and dispensing (CSD) equipment could produce hydrogen that is already cost-competitive with gasoline per mile driven in a conventional (non-hybrid) vehicle. We further showed that mass producing this 578 kg/day system in quantities of just 100 units would reduce hydrogen cost per mile approximately 13% below the cost of untaxed gasoline per mile used in a hybrid electric vehicle. If mass produced in quantities of 500 units, hydrogen cost per mile in a FCEV would be 20% below the cost of untaxed gasoline in an HEV in the 2015-2020 time period using EIA fuel cost projections for natural gas and untaxed ...
This paper extends the analytical procedure described in another paper in these proceedings to analyze a variety of compact and light-weight OSC-designed radioisotope-heated generators. Those generators employed General Purpose Heat Source (GPHS) modules and a converter containing sixteen AMTEC cells of OSC`s revised five-tube design with enhanced cell wall reflectivity described in a companion paper in these proceedings. OSC found that the performance of the generator is primarily a function of the thermal insulation between the outside of the generator`s 16 cells and the inside of its wall. After examining a variety of insulation options, it was found that the generator`s performance is optimized by employing a hybrid insulation system, in which the space between the cells is filled with fibrous Min-K insulation, and the generator walls are lined with tapered ...
Site studies for CANDU type NPP began in a careful manner since 1982 as a first part of the Nuclear Power Plant Romanian Program adopted by political and governmental authorities at the time. A team was charged to develop all packages of the necessary main studies. The first Romanian NPP CANDU 6 type reactor gone to erection on Cernavoda site, planned to have 5 units and, like Wolsong NPP, applied the same design for the nuclear island. For the BOP parts the ANSALDO-GE project was applied with a thorough concern about requirements raised by connection to NSP. The first mission of design and research multi-branch team was to adapt the NPP Cernavoda project having an open water cooling circuit 'once-through' to the new parameters of a close recirculation water cooling circuit. Also, the structural design was re-evaluated for the case of soft foundation strata instead of hard rock ones. The close recirculation water cooling circuit system was applied for PWR NPP type like in French or ...
CANDU 600 nuclear reactors are usually fuelled with STANDARD (STD), 37 rods fuel bundles. Natural uranium (NU) dioxide (UO_2), is used as fuel composition. A new fuel bundle geometry called CANFLEX (CFX) with 43 rods is proposed and some new fuel composition are considered. Flexibility is the key word for the attempt to use some different fuel geometries and compositions for CANDU 600 nuclear reactors as well as for innovative ACR-700/1000 nuclear reactors. The fuel bundle considered in this paper is CFX-RU-0.90 that encodes the CANFLEX geometry, recycled dioxide uranium (RU) with 0.90% enrichment. The goal of this proposal is ambitious: a higher average discharge burn-up up to 14000 MWd/tU and, for the same amount of generated electric power, reduction in nuclear fuel fabrication, reduction of spent nuclear fuel radioactive waste and reduction of refueling operational work by using fewer bundles. An improved sub-channel approach for ...
The central aim of this thesis is to present a new kind of realism that is driven not from the traditional realism/anti-realism debate but from the practice of physicists. The usual debate focuses on discussions about the truth of theories and their fit with nature, while the real practices of the scientists are forgotten. The position I shall defend is called 'phenomenological realism': theories are merely tools to construct other theories and models, including phenomenological models; phenomenological models are the vehicles of representation. The realist doctrine was recently undermined by the argument from the pessimistic meta-induction, also known as the argument from scientific revolutions. I argue that phenomenological realism is a new kind of scientific realism which can overcome the problem generated by the argument from scientific revolutions, and which depend on the scientific practice. The realist tried to overcome ...
Dust detection and control in real time, represent one of the most challenging problem in all those environments where fine and ultrafine airborne particulate solids products are present. The presence of such products can be linked to several factors, often directly related and influenced by the working-production actions performed. Independently from the causes generating dust, airborne contaminants are an occupational problem of increasing interest as they are related to a wide number of diseases. In particular, airborne dusts are well known to be associated with several classical occupational lung diseases, such as the pneumoconiosis, especially at high levels of exposure. Nowadays there is also an increasing interest in other dust related diseases, from the most serious as cancer and asthma, to those related with allergies or irritation and other illnesses, also occurring at lower levels of exposure. Among the different critical factors influencing health risk ...
We have previously shown that avian reovirus (ARV) #sigma#A and #sigma#NS proteins possess dsRNA and ssRNA binding activity and suggested that there are two epitopes on #sigma#A (I and II) and three epitopes (A, B, and C) on #sigma#NS. To further define the location of epitopes on #sigma#A and #sigma#NS proteins and to further elucidate the biological functions of these epitopes by using monoclonal antibodies (MAbs) 62, 1F9, H1E1, and 4A123 against the ARV S1133 strain, the full-length and deletion fragments of S2 and S4 genes of ARV generated by polymerase chain reaction (PCR) were cloned into pET32 expression vectors and the fusion proteins were overexpressed in Escherichia coli BL21 strain. Epitope mapping using MAbs and E. coli-expressed deletion fragments of #sigma#A and #sigma#NS of the ARV S1133 strain, synthetic peptides, and the cross reactivity of MAbs to heterologous ARV strains demonstrated that epitope II on #sigma#A was located at amino acid residues ...
The project aim is to model the hybrid plant at Vaesthamnsverket in Helsingborg using artificial neural networks (ANN) and integrating the ANN models, for online condition monitoring and thermoeconomic optimization, at Vaesthamnsverket. The definition of a hybrid plant is that it uses more than one fuel, in this case a natural gas fuelled gas turbine with heat recovery steam generator (HRSG) and a biomass fuelled steam boiler with steam turbine. The project is a continuation of previous projects where ANN training was done with operational data from the plant. The ANN models have, if required, been updated to better suit the purpose of this project. The thermoeconomic optimization takes into account current electricity prices, taxes, fuel prices etc. and calculates the current production cost along with the 'predicted' production cost. The tool also has a built in feature of predicting when a compressor wash is economically ...
Liquid Zone Control (LZC) System is a 'first-of-its-kind' reactivity control device, designed and implemented at TAPP-3 and 4. The system provides zonal and bulk power control. The system consists of fourteen Zone Control Compartments (ZCCs) containing demineralised light water as neutron absorber. Reactivity control is achieved by varying the level of water in the compartments bi-directionally. Six in-core zircaloy assemblies, housing the fourteen ZCCs and an elaborate process system constitute the LZC system. Measurement of water levels in the ZCCs is done using helium bubbler method. Reliability of ZCC water level measurement is of paramount importance. Commissioning and operating the new system trouble free was a challenge, considering the complex nature of the system. While commissioning the system, level measurement of one of the ZCCs (ZCC - 1) was found erratic and inconsistent. Methodologies were developed to identify the problem and investigations revealed ...
Current light water reactor (LWR) steam generators have been affected by a variety of corrosion and mechanical damage degradation mechanisms. Included are wear caused by tube vibration, intergranular corrosion, pitting, and thinning or wastage of the steam generator tubing and accelerated corrosion of carbon steel supports (denting). The Electric Power Research Institute (EPRI) and the Steam Generator Owners Groups (I, II) have sponsored laboratory and field studies to provide ameliorative actions for the majority of the damage forms experienced to date. Some of the current corrosion mechanisms are aggravated or caused by unique materials choices or materials interactions. New materials have been proposed and at least partially qualified for use in replacement model steam generators, including an advanced LWR design. In so far as possible, the materials choices for the advanced LWR steam ...
The 3D modeling of the thermal hydraulic processes and soluble impurity distribution in the horizontal steam generator PGV-1000 was fulfilled with the thermal hydraulic code STEG. Steady-state operation of horizontal seam generator PGV-1000 was analyzed at nominal power. The modeling of the soluble impurity distribution was fulfilled on the basis of the previous thermal hydraulic modeling results. The processes of the soluble impurity deposition on the steam generator tube bundles and deposits outwash were considered in the mathematical model of the code. The modeling was fulfilled for horizontal steam generators with different peculiarities in construction. Calculation results were compared with experimental results obtained at NPP. The agreement between calculated and experimental results is quite reasonable. Results of modeling are sensible to the peculiarities of the horizontal steam ...
Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries ...
Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries ...
BackgroundNatural disasters result in significant numbers of disabling impairments. Paradoxically, however, the traditional health system response to natural disasters largely neglects health-related rehabilitation as a strategic intervention.ObjectivesTo examine the role of health-related rehabilitation in natural disaster relief along three lines of inquiry: (1) epidemiology of injury and disability, (2) impact on health and rehabilitation systems, and (3) the assessment and measurement of disability.DesignQualitative literature review and secondary data analysis.ResultsAbsolute numbers of injuries as well as injury to death ratios in natural disasters have increased significantly over the last 40 years. Major impairments requiring health-related rehabilitation include amputations, traumatic brain injuries, spinal cord injuries (SCI), and long bone fractures. Studies show that persons with ...
A method and system for enhancing the transient stability of an intertied three-phase electric power generating system. A set of power exporting generators (10) is connected to a set of power importing generators (20). When a transient cannot be controlled by conventional stability controls, and imminent loss of synchronism is detected (such as when the equivalent rotor angle difference between the two generator sets exceeds a predetermined value, such as 150 degrees), the intertie is disconnected by circuit breakers. Then a switch (30) having a 120-degree phase rotation, or a circuit breaker having a 120-degree phase rotation is placed in the intertie. The intertie is then reconnected. This results in a 120-degree reduction in the equivalent rotor angle difference between the two generator sets, making the system more stable and allowing more time for the conventional controls to ...
In an ignition timing control apparatus for controlling the ignition timing of each cylinder in order to reduce knock generation in a multi-cylinder engine, a lag-angle correction is made for the ignition timing of a cylinder in which a knock is generated and at the same time, a slight lag-angle correction is made for the ignition timing of the other cylinders in which no knock is generated. When the operating condition of engine is rapidly changed for example, under the condition in which knock is liable to occur in all cylinders as at rapid acceleration time, a lag-angle correction is made by the same amount as in the knock generating cylinder, for the ignition timing of cylinders in which no knock is generated. When no knock is generated for a predetermined time, a lead-angle correction is made for the ignition timing subjected to the lag-angle correction of ...
Full text of publication follows: Different to the very simple class of homogeneous non-equilibrium models (HEM) an one dimensional thermal-hydraulic theoretical drift-flux based and thus non-homogeneous coolant channel model and, as a result, an in itself complete thermal-hydraulic coolant channel module CCM have been established allowing to simulate in a very general way the steady state and transient behaviour of the most important parameters of a single- or two-phase fluid flowing within any type of heated or non-heated coolant channel (with an eventually varying cross flow area). To avoid mathematical discontinuities at the transition from single- to two-phase flow the coolant channel will, in its general form, be split into different regions, i.e. be looked as a basic channel (BC) which can consist of a number of different flow regimes and can, accordingly, be subdivided into a number of sub-channels (SC-s). All of them belong, obviously, to only two types of SC-s, a SC with an ...
Projected scenarios for the proposed Yucca Mountain repository include significant periods of time when high relative humidity atmospheres will be present, thus the reaction processes of interest will include those known to occur under these conditions. The ideal natural analog for the proposed Yucca Mountain repository would consist of natural borosilicate glasses exposed to expected repository conditions for thousands of years; however, the prospects for identifying such an analog are remote, but an important caveat for using natural analog studies is to relate the reaction processes in the analog to those in the system of interest, rather than a strict comparison of the glass compositions. In lieu of this, identifying natural glasses that have reacted via reaction processes expected in the repository is the most attractive option. The goal of this study is to quantify molecular water diffusion in the ...
As part of the national survey to evaluate natural radioactivity in the environment, concentration levels of natural uranium and "2"2"6Ra have been analyzed in over 300 drinking water samples taken from different locations in Argentina. "2"2"6Ra was determined by "2"2"2Rn emanation and liquid scintillation counting, and natural uranium by a fluorimetric procedure. Values ranging from 0.03 to 24 #mu#g.l"-"1 of natural uranium and from 0.06 to 50 #mu#g.l"-"1, were measured on drinking water samples taken from tap water systems and private wells, respectively. Concentrations up to 15 mBq.l"-"1 and to 22 mBq.l"-"1 of "2"2"6Ra were found in drinking water samples taken from tap water systems and private wells, respectively. These values are compared with the reference values accepted for drinking water. Based on the water intake rate, the age distribution and the measured concentrations, an annual collective ...
The indoor climate of school buildings have been much debated recently. Many problems connected with air quality and thermal comfort are caused by bad maintenance, fitted carpets and no sunshades. Mechanical ventilation in schools has gained a bad reputation and many municipalities are seeking other solutions when building new schools. Natural ventilation according to the ''Swedish model'' does not use air filters or heat recovery from the outgoing air and achieve low energy consumption by reducing the airflow substantially in cold weather. Most of the naturally ventilated schools have supply air culverts of concrete below ground outside the building and in the basement. This is also true of schools using hybrid ventilation, where natural and mechanical ventilation is combined. The naturally ventilated schools often use manual control of the ventilation, which may not ...
The Natural Gas Vehicle Challenge `92, organized by Argonne National Laboratory and sponsored by the US Department of Energy, the Energy, Mines, and Resources - Canada, the Society of Automotive Engineers, and many others, resulted in 20 varied approaches to the conversion of a gasoline-fueled, spark-ignited, internal combustion engine to dedicated natural gas use. Starting with a GMC Sierra 2500 pickup truck, donated by General Motors, teams of college and university student engineers strived to optimize Chevrolet V-8 engines operating on natural gas for improved emissions, fuel economy, performance, and advanced design features. This paper focuses on the results of the emission event, and compares engine mechanical configurations, engine management systems, catalyst configurations and locations, and approaches to fuel control and the relationship of these parameters to engine-out and tailpipe emissions of regulated ...
In 1983, the first modern urban transit bus powered by an alternative transportation fuel took to the roads in the USA. A little more than a decade later, about 2.5% of all USA buses are powered by alternative transportation fuels and about 20% of the new bus orders for delivery by 1998 will be powered by alternative fuels, mostly by natural gas. There are over 2,200 natural gas buses in operation or on order, plus about 600 additional buses powered by other alternative fuels. When these orders are completed, alternative fuel buses will constitute over 4.4% of the urban bus fleet in the USA. The widespread use of natural gas buses in the USA provides an important transition pathway for hydrogen vehicles because of the similarities between distribution, refueling and onboard energy storage technologies for the two fuels. Projects demonstrating advanced hybrid-electric buses powered by natural gas or ...
Gas Supplies of Interstate Natural Gas Pipeline Companies 1987 was prepared by the Reserves and Natural Gas Division, Office of Oil and Gas, Energy Information Administration (EIA). The publication provides information on the total reserves, production, and deliverability capabilities of the 87 interstate pipeline companies required to file the Federal Energy Regulatory Commission (FERC) Form 15, ''Interstate Pipeline's Annual Report of Gas Supply.'' This publication is the 25th in a series of annual reports on the total gas supplies of interstate pipeline companies since the inception of individual company reports to the Federal Power Commission (FPC) in 1964 for report year 1963. This publication provides information on the interstate pipeline companies' supply of natural gas during calendar year 1987, for use by the FERC for regulatory purposes. It also provides ...
A natural gas and diesel dual-fuel turbocharged compression ignition (CI) engine is developed to reduce emissions of a heavy-duty diesel engine. The compressed natural gas (CNG) pressure regulator is specially designed to feed back the boost pressure to simplify the fuel metering system. The natural gas bypass improves the engine response to acceleration. The modes of diesel injection are set according to the engine operating conditions. The application of honeycomb mixers changes the flowrate shape of natural gas and reduces hydrocarbon (HC) emission under low-load and lowspeed conditions. The cylinder pressures of a CI engine fuelled with diesel and dual fuel are analysed. The introduction of natural gas makes the ignition delay change with engine load. Under the same operating conditions, the emissions of smoke and NO{sub x} from the dual-fuel engine are both reduced. The HC and ...