Science.gov (United States)

A model is presented for describing the Amputee Independent Prosthesis Properties (AIPP) of complete assemblies of trans-tibial prosthetic components distal to the socket. This new AIPP model includes features of both lumped parameter and roll-over models and describes prosthesis properties that are of importance in stance phase, including prosthetic foot geometry, normal stiffness, shear stiffness, and damping (energy dissipation). Methods are described for measuring the parameters of the AIPP model using a custom test-rig, commercial load-cell, and a motion capture system. Example data are presented for five pylon angles reflecting the shank angles seen in normal gait. Through the inclusion of measured AIPP in future in-vivo studies comparing different prostheses more generic information, as opposed to product specific claims, will become more widely available to inform future designs, prescription, and alignment ...

British Library Electronic Table of Contents (United Kingdom)

Deltombe T, Gustin T. Selective tibial neurotomy in the treatment of spastic equinovarus foot in hemiplegic patients: a 2-year longitudinal follow-up of 30 cases. Objective To assess the long-term efficacy of selective tibial neurotomy in the treatment of spastic equinovarus foot in hemiplegic patients. Design Intervention study (before-after trial) with an observational design and 2-year follow-up. Setting Spasticity group in a university hospital. Participants Hemiplegic patients (N=30) with spastic equinovarus foot. Intervention A selective neurotomy was performed at the level of the motor nerve branches of the tibial nerve. Main Outcome Measures Spasticity (Ashworth scale), muscle strength (Medical Research Council scale), passive ankle dorsiflexion, gait parameters (6 min walking test...

Energy Technology Data Exchange (ETDEWEB)

This document describes a simple and general way to generate House Simulation Protocol (HSP)-consistent internal sensible and latent loads in unoccupied homes. It is newly updated based on recent experience, and provides instructions on how to calculate and set up the operational profiles in unoccupied homes. The document is split into two sections: how to calculate the internal load magnitude and schedule, and then what tools and methods should be used to generate those internal loads to achieve research goals.

UK PubMed Central (United Kingdom)

There has been a controversy as to whether or not the non-pathological flat foot and high-arched foot have an effect on human walking activities. The 3D foot scanning system was employed to obtain static...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This document presented the results of a full-scale pile load tests conducted on helix pile foundations supporting power transmission towers in northern Manitoba. The site conditions were described along with pile installation and the performance of the foundations. The pile load tests were carried out in 2 different soil conditions, notably soft to firm clays and stiff high plastic clays with silt varves. The performance of the helix pile foundations were examined under axial compressive and axial tension (uplift) loading conditions. The results of the compressive load tests were presented in the form of load settlement curves while the results of the uplift load tests were presented in the form of load displacement curves. Both types of ...

Energy Technology Data Exchange (ETDEWEB)

A new test methodology is described which allows access to loading rates that lie between split Hopkinson bar and shock-loading techniques. Gas gun experiments combined with velocity interferometry techniques have been used to experimentally determine the intermediate strain-rate loading behavior of Coors AD995 alumina and Cercom silicon-carbide rods. Graded-density materials have been used as impactors; thereby eliminating the tension states generated by the radial stress components during the loading phase. Results of these experiments demonstrate that the time-dependent stress pulse generated during impact allows an efficient transition from the initial uniaxial strain loading to a uniaxial stress state as the stress pulse propagates through the rod. This allows access to intermediate loading rates over 5 x 10{sup 3}/s to a few times ...

Energy Technology Data Exchange (ETDEWEB)

Jittery (ji) is a recessive mouse mutation on Chromosome 10 characterized by progressive ataxic gait, dystonic movements, spontaneus seizures, and death by dehydration/starvation before fertility. Recently, a viable neurological recessive mutation, hesitant, was discovered. It is characterized by hesitant, uncoordinated movements, exaggerated stepping of the hind limbs, and reduced fertility in males. In a complementation test and by genetic mapping we have shown here that hesitant and jittery are allelic. Using several large intersubspecific backcrosses and intercrosses we have genetically mapped ji near the marker Amh and microsatellite markers D10Mit7, D10Mit21, and D10Mit23. The linked region of mouse Chromosome 10 is homologous to human 19p13.3, to which several human ataxia loci have recently been mapped. By excluding genes that map to human 21q22.3 (Pfkl) and 12q23 (Nfyb), we conclude that jittery is not likely to be a genetic mouse ...

Energy Technology Data Exchange (ETDEWEB)

An effect of load conditions on Corrosion Fatigue Crack Propagation (CFCP) behavior of High Performance Steel (HPS) under seawater environment was investigated. Fatigue crack propagation tests under several load conditions including stress ratio and load frequency were conducted in air and 3.5% NaCl solution environments. Corrosion/fatigue ratio factor, C/F, particularly was defined to analyze the effect of such conditions. As shown in the results, a decrease of load ratio and frequency leads to an increase of C/F factor. Consequently, under lower loading frequency and stress ratio, the seawater condition causes much more significant effect on CFCP behavior of HPS.

Energy Technology Data Exchange (ETDEWEB)

0pen ended piles develop internal frictional resistance between the internal soil plug end the pile wall during axial loading. Current pipe pile design practice assumes that the ultimate internal skin friction is of the same order of magnitude as the outer skin friction. This paper describes a series of laboratory pile load tests on instrumented model pipe piles, designed to investigate the development of plug stresses and skin friction along the plug length during pile loading. The piles contain sand columns of various relative densities and of different heights. The soil plugs are loaded to failure under fully drained conditions. The test data indicate that internal skin friction in sand can be substantially higher than assumed in conventional design practice. This finding could lead to significant economical savings on future pipe pile foundations in sand.

Science.gov (United States)

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at two elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of th...

International Nuclear Information System (INIS)

Load-deflection characteristics of alumina and alumino-silicate fibrous blankets were experimentally determined. Load retention and springback capability of combinations of these materials were measured in a 10,000-hour test at surface temperatures of 650 to 1000"0C (1200 to 1832"0F). Experimental results are presented and future testing plans are discussed.

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) was designed to test fast-reactor fuels and other nonfuel materials. In its 37 reactor cycles of operations, the FFTF reactor has performed very well and successfully completed all the irradiation testings with an operating efficiency factor as high as 98%. Since FFTF is an experimental reactor, its core loading changed from cycle to cycle. Depending on the number of test assemblies in the core and their location, the core loading can change significantly from an essentially homogeneous core loading to a relatively nonhomogeneous or even highly localized heterogeneous loading. Consequently, the core reload design and initial criticality analyses were required for each operating cycle. The zero power initial critical control rod bank height was predicted before each reactor startup. The ...

Science.gov (United States)

This paper describes the design of a test rig, which is used to apply a representative pressure load to a full-scale composite sandwich secondary aircraft structure. A generic panel was designed with features to represent those in the composite sandwich secondary aircraft structure. To provide full-field strain data from the panels, the test rig was designed for use with optical measurement techniques such as thermoelastic stress analysis (TSA) and digital image correlation (DIC). TSA requires a cyclic load to be applied to a structure for the measurement of the strain state; therefore, the test rig has been designed to be mounted on a standard servo-hydraulic test machine. As both TSA and DIC require an uninterrupted view of the surface of the test panel, an important consideration in the design is facilitating the optical access for the ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) bottom-loading transfer cask (BLTC) system is designed to provide ex-vessel fuel transfers of irradiated reactor components between the reactor containment building and the LMFBR shipping cask in the reactor service building. This system is being procured from National Lead Industries, Wilmington, Delaware, under management of Aerojet Manufacturing Company.

Energy Technology Data Exchange (ETDEWEB)

The nucleation of microdamage under dynamic loading was investigated through planar impact experiments accomplished with a light gas gun. The microscopic observation of recovered and sectioned specimens showed that microcracks were nucleated only by cracking of brittle particles inside material. However, for comparison the in situ static tensile tests on the same material conducted with a scanning electron microscope showed that the microcracks were nucleated by many forms those were fracture of ductile matrix, debonding particles from matrix and cracking of brittle particles. The quantitative metallographic observations of the specimens subjected to impact loading showed that most of the cracked particles were situated on grain boundaries of the aluminum matrix. These facts suggested the concept of critical size and incubation time of submicroscopic cavities in the dynamic case and the mechanism of embryo-damage induced ...

Science.gov (United States)

Tests of Tail Buffet on the CF-18 Aircraft, AGARD Specialists' Meeting on Aircraft Loads due to. Flow Separation, Sorrento, Italy, Apr. 16, 1990. ...

Energy Technology Data Exchange (ETDEWEB)

An experimental apparatus has been built that allows direct measurement of the oil film thickness in a bearing that is subjected to dynamic loads and shaft speeds representative of those occurring in automotive engine connecting rod, big-end bearings. Dynamic motion of the shaft, relative to the bearing, is measured as a function of shaft rotational angle, using non-contact, eddy-current probes. A computer based data acquisition system is used to measure, record, and analyze the journal position in the bearing. The test bearing is 63.5 mm in diameter by 25.4 mm long, and is loaded using a servo-hydraulic actuator rated at 98.3 kN. The journal has an operating speed of 500 to 3800 rpm. The actuator is controlled by a computer-generated waveform that can duplicate load profiles developed by various engines operating at a wide range of conditions. Measurements taken with the shaft statically ...

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of single-fiber pullout tests for deformed and smooth steel fibers embedded in the newly developed very-high strength concrete (VHSC) matrixes. The pullout test program involved four types of steel fibers, eight compressive strengths of VHSC matrixes, and two normal concrete strengths. Test results have shown that pullout behavior of different steel fiber reinforced VHSC composites is influenced by the matrix strength and fiber end condition (smooth, flat end, or hooked). Results reveal that both maximum pull-out load and total pullout energy increases as matrix strength increases for all deformed fibers that did not rupture. The test results also indicated that the increase in total pullout energy is more significant than that in peak load.

Energy Technology Data Exchange (ETDEWEB)

The data center in this study had a total floor area of 8,580 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 440 racks, and was located in a 208,240 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but served by the main building chiller plant and make-up air system. Additionally, it was served by a single electrical supply with no provision for backup power. The data center operated on a 24 hour per day, year-round cycle, and users had all hour full access to the data center facility. The study found that data center computer load accounted for 23% of the overall building electrical load, while the total power consumption attributable to the data center including allocated cooling ...

Science.gov (United States)

Five cycles of loading, elution, and regeneration were performed to remove technetium from a Hanford waste sample retrieved from Tank 241-AW-101 using SuperLig 639 resin. The waste sample was diluted to 4.95 M Na plus and then was processed to remove 137Cs through dual ion exchange columns each containing 15 mL of SuperLig 644. To remove 99Tc, the cesium decontaminated solution was processed downwards through two ion exchange columns, each containing 12 mL of SuperLig 639 resin. The columns, designated as lead and lag, each had an inside diameter of 1.45 cm and a height of 30 cm. The columns were loaded in series, but were eluted and then regenerated separately. The average technetium loading for the cycles was 250 BV at 10 percent breakthrough. There was no significant difference in the loading performances among the five cycles. The percent removal of 99Tc was greater than 99.94 percent and the ...

Energy Technology Data Exchange (ETDEWEB)

The staring point of the project was to design and construct, by taking the silvicultural point of view into account, a harvesting and processing system especially for energy-wood, containing manually driven bundling harvester, automatizing of the harvester, and automatized loading. The equipment forms an ideal method for entrepreneur`s-line harvesting. The target is to apply the system also for owner`s-line harvesting. The profitability of the system promotes the utilization of the system in both cases. The objectives of the project were: to construct a test equipment and prototypes for all the project stages, to carry out terrain and strain tests in order to examine the usability and durability, as well as the capacity of the machine, to test the applicability of the Eko-Log system in simultaneous harvesting of energy and pulp woods, and to start the marketing and manufacturing of the products. The ...

International Nuclear Information System (INIS)

Carbon fibre composite (CFC) was irradiated by hot plasma streams at plasma gun facility MK-200UG. The CFC targets were tested by plasma loads relevant to Edge Localized Modes (ELM) and mitigated disruptions in ITER. Onset condition of CFC evaporation and properties of evaporated carbon were studied by use of infrared pyrometry and visible spectroscopy.

Energy Technology Data Exchange (ETDEWEB)

The ability of the /sup 252/Cf-source-driven neutron noise analysis method to measure subcriticality has been demonstrated in a variety of experimental configurations of fissile materials. Calculations for an approximately 4-m-dia configuration of light water reactor (LWR) fuel elements indicated the feasibility of measuring the subcriticality of large, loosely coupled arrays of LWR fuel elements by this same method. These analysis suggested application to the initial loading of both pressurized and boiling water reactors, zero-power testing of reactors (such as shutdown margin measurements after initial loading), light water reactor refueling, and safe storage of LWR spent fuel. In the fuel storage application, direct measurement of subcriticality in the actual fuel storage facilities provides the parameter which is directly related to criticality safety.

Energy Technology Data Exchange (ETDEWEB)

The objective of the research was to develop a machine combination for harvesting of small wood, which carries out both the harvesting and forest haulage. The development was started in September 1995. The first prototype of the machine is ready. A Lokomo 910 forest tractor was acquired for the tests. The prototype has been mounted on the tractor, and the tests have been started in the beginning of March 1996. The reconstruction of the device will be made after the tests, as well as the description of different working praxis. Time consumption study and the analysis of it will be made after the equipment tests. The device consists of a grapple equipped with a guillotine cutting device mounted on the tractor. The actual felling is made stem by stem in the test phase. The stem can be forwarded directly into the load or it can be left aside, and new stems can be ...

Energy Technology Data Exchange (ETDEWEB)

The Japan Atomic Energy Research Institute has conducted a piping reliability test program to demonstrate the safety and reliability of light water reactor primary piping. In this program, pipe fatigue test, leak-before-break (LBB) verification test and pipe rupture test were carried out to examine the integrity of piping, to verify the LBB and to demonstrate the effectiveness of protective measures against jet impingement and pipe whip loads under a pipe rupture event.In the pipe fatigue test, a procedure to predict the fatigue crack growth was developed, and the integrity of piping during the plant service life was evaluated. In the LBB verification test, the pipe fracture test and the leak rate test were performed to verify the LBB in the primary piping.In the pipe rupture ...

Energy Technology Data Exchange (ETDEWEB)

Experimental data on the material characteristics of structures subjected to thermal and mechanical cycling are needed for designing structural parts for creep and creep-fatigue interaction. Moreover, high-temperature low-cycle fatigue data are not sufficient to predict the fatigue creep lifetime. In order to check the reliability of steam generators, tests on pipe materials are conducted under cyclic thermal loading. The tests have been performed on an iron-nickel chromium alloy (alloy 800). Isothermal low-cycle fatigue tests have been conducted at 550 C. 15 refs.

Energy Technology Data Exchange (ETDEWEB)

A parametric experimental investigation of an 85 millimeter bore angular contact ball bearing running in RP-1 fuel was performed at speeds of 10,000 to 24,000 rpm. Thrust loads were varied from 4450 to 17,800 Newtons (1000 to 4000 lbs.). Radial loads were varied from 1335 to 13,350 Newtons (300 to 3000 lbs.). RP-1 lubrication for the bearing was provided through a stationary jet ring located adjacent to the test bearing outer ring. Increases in both the thrust and radial loads resulted in increased bearing temperature, while increases in shaft speed resulted in much more dramatic increases in bearing temperature. These trends are typical for ball bearings operating under these types of conditions. Results are given for outer ring temperatures of the test bearing at the various test conditions employed. In addition, the heat energy removed from the bearing by the ...

Science.gov (United States)

A 206-size hybrid (ceramic/steel) cylindrical roller bearing was tested in MIL-L-23699 C oil at several speeds and loads. Heat-generation data was collected and subsequently correlated with bearing-analysis software. Bearing-cage slip data was also collected at various oil-flow rates, oil temperatures, and with both MIL-L-7808 J and MIL-L-23699 C oils. The hybrid bearing was tested in MIL-L-23699 C oil for for 25 hours at 2220 N radial load and 1.08 MDN shaft speed. The hybrid bearing technology demonstrated in the report is applicable to the Integrated High Performance Turbine Engine Technology Initiative. 15 refs.

British Library Electronic Table of Contents (United Kingdom)

A dry interim storage facility has been constructed at the Wolsung power plant in Korea. This dry storage facility has seven separated modules. There are 40 long slender cylinders in one module. In one cylinder, ten baskets where sixty CANDU spent fuel bundles are loaded are stacked and stored. For this dry storage facility, analyses and tests for hypothetical accident conditions that might occur while moving and storing the baskets into a cylinder were performed. In a demonstration test, one of test basket models did not satisfy one of the safety-related requirements. Thus, the revised basket designs were generated using a structural evaluation based on finite element analyses and specimen tests. Among these revised designs, one design was chosen as a final revised basket design. The fina...

International Nuclear Information System (INIS)

Commissioning of a Pressurized heavy water reactor (PHWR) plant of NPCIL involves three phases viz phase-A which consist of pre-criticality activities such as hydro test, air hold test, no load test of motors etc., phase-B consist of criticality and post criticality physics experiments. The phase-C, which is considered the major phase, consist of initial power raise to about 10 % , TG rolling, synchronization, going to significant power in steps and performance tests such as load rejection tests from various power levels. In order to have smooth commissioning for the Phase-C, an integrated team consisting of engineers from various design and analysis groups of NPCIL headquarters was formed to participate along with site O and M engineers, closely observe and coordinate phase-C commissioning activities. During this commissioning some major ...

Science.gov (United States)

All first-stage experimental tests were completed for Task 4 (and the Contract). The first-stage one-liter autoclave tests that were made were duplicates of Run 41-LA. The conditions used were chosen last quarter to reduce the cost of the first-stage of the process from those used at the conclusion of Task 3. Filtration and second-stage tests were made using the products of the first-stage tests. Post-second-stage filtration, tested as an alternative to interstage (pre-second- stage) filtration, resulted in low filtration rates. Different catalyst loadings and type and residence time for second-stage hydrotreating were explored. Longer residence times did not result in significantly more resid conversion. Higher catalyst loadings were more effective in converting the resid at the same residence time. The material and elemental balances for ...

International Nuclear Information System (INIS)

One of the limiting contributors to the heat load constraint for a long term spent fuel repository is the decay of americium-241. A possible option to reduce the heat load produced by Am-241 is to eliminate it via transmutation in a light water reactor thermal neutron environment, in particular, by taking advantage of the large thermal fission cross section of Am-242 and Am-242m. In this study we employ lattice loading optimization techniques to define the loadings and arrangements of fuel pins with blended americium and uranium oxide in boiling water reactor bundles, specifically, by defining the incineration of pre-loaded americium as an objective function to maximize americium transmutation. Subsequently, the viability of these optimized lattices is tested by assembling them into bundles with Am-spiked fuel pins and by loading these ...

Science.gov (United States)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This paper discusses the development of a model for the simulation of these stochastic loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Streamtube analysis is employed, which includes the effects of wind shear. Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. Calculations are presented for the VAWT 34-m Test Bed currently being assembled at Bushland, Texas. Time histories of the loads, as well as their Fourier spectra, are presented and discussed. An unexpected finding is that the average output ...

Energy Technology Data Exchange (ETDEWEB)

Pile foundations in several coastal and offshore structures are subjected to significant amounts of lateral loads due to wave action. Usually batter piles are adopted to resist large lateral loads. In this investigation an attempt has been made to study the behavior of batter pile in clayey soils through an experimental program carried out on instrumented model aluminium piles of 26 mm diameter in a test tank of size, 1,200 mm x 800mm x 1,100 mm. The pile was instrumented with electrical resistance type strain gauges to determine the bending moment variations along the depth of embedment of pile. Bending moment vis depth relationships were used to determine the Soil reaction (p) and lateral displacement (y) along the length of the pile for the applied load. From the bending moment vs depth curves it is found that depth of maximum bending moment is greater for negative batter pile than for vertical and ...

International Nuclear Information System (INIS)

The Wendelstein 7-X (W7-X) modular stellarator is under construction at the Max-Planck-Institut fuer Plasmaphysik in Greifswald, Germany. The W7-X magnet system contains 70 coils made up from helium cooled superconducting cables in aluminium alloy (EN AW-6063) jackets. Several hundred connections of the jacket to the cable joints are made by aluminium-to-aluminium welds. Due to geometrical and thermal boundary conditions these welds cannot be accomplished free from defects. Microscopic analyses of the welds show that a variety of small flaws such as cracks and pores develop during welding. The welds have thus to be dimensioned accordingly, and appropriate weld qualification, investigation and testing has to be done in order not to jeopardise the structural integrity and leak tightness. The weld is mechanically loaded during cool-down due to the difference in thermal contractions between the GRP insulation and the aluminium, and during operation ...

Energy Technology Data Exchange (ETDEWEB)

The data center in this study had a total floor area of 3,024 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 147 racks, and was located in a 96,000 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but was served by the main building chiller plant and make-up air system. Additionally it was served by only a single electrical supply with no provision for backup power in the event of a power outage. The Data Center operated on a 24 hour per day, year-round cycle, and users had full-hour access to the data center facility. The study found that data center computer load accounted for 15% of the overall building electrical load, while the total power consumption attributable to the data center ...

Energy Technology Data Exchange (ETDEWEB)

Machine condition monitoring (MCM) has the capability to predict equipment maintenance needs which can reduce forced down-time and facilitate the avoidance of catastrophic failures and the consequential secondary damage. It can be used to allow confident deferral of routine maintenance, and improve equipment performance, availability, reliability and safety. In order to capitalize on the potential benefits of MCM directed toward power transformers two types of vibration tests were conducted on transformers owned and operated by Cargill Inc. and IES Utilities at the Bridgeport corn plant in Eddyville, Iowa. These tests involved collecting vibration signals from the transformer tank walls during transformer energization at no-load and during steady state operation at various loads. These vibration signals were then used to detect deterioration of internal mechanical integrity. Both types of ...

Energy Technology Data Exchange (ETDEWEB)

Automated, variable volume unloaders provide the ability to smoothly load/unload reciprocating compressors to maintain ideal operations in ever-changing environments. Potential advantages provided by this load control system include: maximizing unit capacity, optimizing power economy, maintaining low exhaust emissions, and maintaining process suction and discharge pressures. Obstacles foreseen include: reliability, stability, serviceability and automation integration. Results desired include: increased productivity for the compressor and its operators, increased up time, and more stable process control. This presentation covers: system design features with descriptions of how different types of the devices were developed, initial test data, and how they can be effectively operated; three actual-case studies detailing the reasons why automated, hydraulically controlled, variable volume, head-end unloaders were chosen over ...

Energy Technology Data Exchange (ETDEWEB)

Discontinuously reinforced aluminium-based composites containing particulate or whisker SiC reinforcements at different volume fractions, were produced via a powder-route. Isothermal creep tests have been carried out at 270, 300 and 320 C. During these tests axial and transverse strains were monitored using a non-contacting laser scanning extensometer arrangement. At the same time neutron diffraction has been used to measure the elastic phase strain evolution with composite creep deformation. It was found that after the initial loading the phase strains remained essentially constant during primary and secondary creep. This indicates that the initial matrix/reinforcement inelastic misfits remain largely unchanged, probably due to the setting up of a dynamic equilibrium between misfit generation and stress relaxation. For each system, the neutron data has been combined with Eshelby modelling to obtain a measure of the ...

British Library Electronic Table of Contents (United Kingdom)

Equinovarus of the foot is the most common lower extremity deformity following traumatic brain injury. We evaluated outcomes of the split anterior tibialis tendon transfer (SPLATT) for correction of equinovarus in 47 patients with hemiplegic traumatic brain injury and specifically studied differences in outcomes with two tendon fixation techniques. Seventeen patients constituting Group I underwent fixation with one technique and 30 constituting Group II had another technique. Patients in both groups had appropriate procedures based on dynamic electromyography and gait analyses. Both groups were demographically comparable. All 47 feet were corrected to plantigrade position. Thirty-six of 47 patients became brace-free at final followup. There was a notable decrease in the use of ambulatory a...

Energy Technology Data Exchange (ETDEWEB)

The behavior of MEMS devices is limited by the strength of critical features such as thin ligaments, oxide cuts joining layers, pin joints and hinges. Devices fabricated at Sandia's Microelectronic Development Laboratory have been successfully tested to investigate these features. A series of measurements were performed on samples with gage lengths of 15 to 1000 microns, using conventional and tungsten coated samples as well as samples that include the critical features of standard components in the test section. Specimens have a freely moving pin joint on one end that anchors the sample to the silicon die to allow rotation to reduce effects of bending. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. Load is calculated by resolving the measured lateral and normal forces into the applied tensile force and frictional ...

Science.gov (United States)

The reverse approach to critical (RAC) experiments were performed in the ZPR-IX critical facility at Argonne National Laboratory. One of the major objectives of this project is to determine the adequacy of the low-level flux monitor (LLFM) detectors for initial loading of the Fast Flux Test Facility (FFTF). 5 references. (auth)

International Nuclear Information System (INIS)

The design characteristic of the autocontrol technique of the combined centrifuge is introduced. Digital technique, vary structure control and interface technique, graphical display techniques, digital communication technique as well as electronic technique are applied in the course of research. Automation in the operation of large scale combined centrifuges and the course of combined test has been realized and it can coordinate with other systems of status monitoring, data collecting and centrifugal force-aerodynamic force matched load automatically

Energy Technology Data Exchange (ETDEWEB)

The susceptibility of CHN35VT-VD and 08CH18N10T stainless steels to stress corrosion cracking in water environment, simulating water solution found in threaded holes, was investigated using rising load line displacement tests of precracked C(T) specimens. To judge the role of oxidant on stress corrosion cracking of both stainless steels, the effect of dissolved oxygen content (fully deaerated water, water aerated at the beginning of the test) was studied. 7 refs.

International Nuclear Information System (INIS)

Depth sensing indentation tests were carried out to obtain load-penetration depth curves of SiAlON-ZrO_2 ceramics under different peak loads ranging from 200 to 1800 mN. The values of indentation hardness (H_O_P, H_C_C) and reduced elastic modulus (E_O_P, E_C_C) were calculated by using Oliver-Pharr (OP) and Cheng-Cheng (CC) methods. The experimental results revealed that the indentation hardness and reduced elastic modulus exhibit peak-load dependence, i.e. indentation size effect. Both indentation hardness and reduced elastic modulus values were obtained by considering indenter tip roundness and machine compliance. These values obtained from the OP method are higher than from the CC method. On the other hand, h_f/h_m ratios were used to clarify the indentation deformation behaviour of the SiAlON-ZrO_2 ceramic. The experimental h_f/h_m values were lower than the reported critical value (0.7) for all ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF)is a 400 MW (th) sodium-cooled fast flux test reactor located on the Hanford Site in southeastern Washington State. The FFTF is operated by the Westinghouse Hanford Company for the United States Department of Energy. The FFTF is a three loop plant designed primarily for the purpose of testing full-scale core components in an environment prototypic of future liquid metal reactors. The plant design emphasizes features to enhance this test capability, especially in the area of the core, reactor vessel, and refueling system. Eight special test positions are provided in the vessel head to permit contact instrumented experiments to be installed and irradiated. These test positions effectively divide the core into three sectors. Each sector requires its own In-Vessel Handling Machine (IVHM) to access all the core positions. Since the ...

Energy Technology Data Exchange (ETDEWEB)

This book presents the proceedings of a conference dedicated to the design and operation of pipework in all its aspects, involving both metallic and non-metallic materials. Topics considered include a study of single mitre pipe bends using the finite element method; tests to failure of GRP pipe bends under in-plane flexural loading; finite element stress analysis of an equal diameter branch pipe intersection subjected to internal pressure and in-plane moment loadings; finite element stress analysis of extruded outlet tee junctions; design of pipework on the British PWR; a review of advanced remanent life methods for pipes operating in the creep range; pipe whip analysis and design; damping values for piping systems; pipework snubbers based on electro-rheological fluids; and the seismic design of piping systems in the flexible range.

British Library Electronic Table of Contents (United Kingdom)

Durability is a major limitation of current proton exchange membrane fuel cells. Mechanical stress due to hygro-thermal cycling is one failure mechanism of the polymer electrolyte membrane. In previous work the cyclic rate, temperature, and hydration dependent elastic-viscoplastic mechanical behavior of Nafion has been extensively investigated in uniaxial and biaxial tension, serving as a data basis and means of validation for a three-dimensional constitutive model. Here, the important effect of loading via constrained swelling is studied. Specifically, two types of loading are investigated: partially constrained swelling via a bimaterial swelling test and hygro-thermal cycling within a fuel cell. The bimaterial swelling conditions are examined via experiments in conjunction with modeling....

Science.gov (United States)

A method for determining the critical debond size between the facesheet and the core in composite sandwich panels under in-plane compression is described. The approach uses fracture mechanics together with a buckling criterion for a debonded faceskin. The technique yields predictions for the critical in-plane compressive load for debond propagation as a function of core-to-faceskin debond size, faceskin thickness, lay-up, composite material properties, and honeycomb properties and geometry. A computer program, developed in this work, calculates the critical buckling load and facesheet deformed shape by solving an eigenvalue problem. The output predicts, for several cases, critical initial debond lengths comparable to those that have been observed on tests on sandwich panels.

Energy Technology Data Exchange (ETDEWEB)

Wood polymer composite (WPC) specimens were produced by impregnating a tropical wood with methyl methacrylate and subsequently polymerised by ..gamma..-irradiation. Beam specimens of varying weight percentages of polymer were then subjected to a three point bend creep test under a constant load condition, for 250, 300 and 350 N. A Norton-Bailey (power law) mathematical model was used to describe the creep behavior, with the creep components determined by a nonlinear regression analysis. Significant creep improvements were obtained from the composite specimens as compared to the untreated wood specimens. Results indicated that maximum creep resistance is obtained when the amount of polymer loading exceeded 30%. An interfacial interaction between the polymer and the wood cell wall was used to account for the behavior of the increase in the creep resistance.

British Library Electronic Table of Contents (United Kingdom)

North American design codes are now committed to the development of load and resistance factor design (LRFD) for reinforced soil structures including internal stability limit states. Reliability-based analysis is required to carry out these calibrations. A framework for LRFD calibration has been proposed by the writers that requires bias statistics for load and resistance terms for each limit state function. In this paper the formulation of the limit state for reinforcement tensile rupture is developed and the component strength-reduction bias statistics identified. The paper describes how to compute bias statistics from project-specific installation damage trials for use in reliability-based design for the reinforcement rupture limit state or using data from multiple sources for LRFD cali...

International Nuclear Information System (INIS)

The paper describes the experimental and analytical results of the pipe whip tests performed under the PWR LOCA conditions using 4, 6 and 8 inch test pipes. The tests were carried out at an initial pressure and a temperature of 15.7 MPa and 325 "0C. Two different types of tests were performed. One was the cantilever type pipe whip test using the test pipe of 3000 mm in length and U-shaped restraints. The other was the cross-over leg pipe whip test using a 1/6 model of piping in the PWR nuclear power plants. The cantilever type pipe whip tests were performed to investigate the influences of overhang length and pipe diameter on the pipe whip behavior. The movement of the test pipe is limited effectively by the restraints when the overhang length is short. The restraint force increases in proportion to ...

Energy Technology Data Exchange (ETDEWEB)

Stress corrosion cracking tests in constant extension rate tensile (CERT) and constant load tensile (CLT) tests were conducted on Ni-xCr- 9Fe-yC in Ar, water, and a LiOH-boric acid solution. Cr and C improve the resistance of Ni-base alloys to IG cracking in both Ar and water at 360C. Since creep plays a role in IG cracking, one possible explanation for the role of the environment involves its effect on the creep. Experiments were conducted on the role of C in the deformation behavior and failure mode of Ni-16Cr-9Fe. Constant load experiments were conducted on Ni-16Cr-9Fe to determine if the CLT test is more aggressive than CERT. The electron backscattering technique in a SEM is being developed in order to extend the IG cracking studies to grain sizes typical of commercial alloys, 20-30 microns.

Energy Technology Data Exchange (ETDEWEB)

Method is proposed for expanding the pile foundation elastic analysis method (displacement method) to cover a larger displacement region, and its appropriateness is verified by a field test. In this report, stability calculation is discussed in which the present displacement method is expanded by assuming an equivalent plastic hinge on the pile head and by replacing the soil spring in the large displacement region with an equivalent linear elastic spring. A static horizontal loading test is conducted for a foundation using a real pile, which is an application of this method. On the assumption that a hinge is generated on the pile head, the pile spring constant of the current displacement method is replaced with a value that takes into consideration the plastic hinge region, and this enables the analysis of pile behavior even after breakdown. This method is applied to the result of a loading ...

Energy Technology Data Exchange (ETDEWEB)

In order to verify long-term reliability of amorphous alloy wound core distribution transformers, accelerated aging tests and field trials used by actual transformers were practiced. As for accelerated aging tests, short-circuit tests were added to imitate mechanical stress in operation on a utility's distribution system. As a result, even after the equivalent of 30 years, which was the normal expected transformer's life, magnetic characteristic was unchanged, so these transformers could be operated. Also, about field trials, two hundred transformers of four kinds were installed on a utility's distribution system to look into no-load characteristics. They were equipped with a mechanism to measure load current, background vibration and lightning surge current, so the influence for magnetic characteristic could be inspected. As a result, remarkable change ...

International Nuclear Information System (INIS)

Analyses of the date obtained from the instrumented impact test and of its correlation with static and dynamic J integral values and various tensile properties are made in this study. It is shown that a dynamic bending yield load recorded in the instrumented Charpy V test can be easily converted to a dynamic tensile yield stress using Server's equation. It is also possible to estimate a true fracture strain, COD value, and SZW easily if the load point displacement is recorded. Temperature dependency of Charpy V energy and J integral values is rather well simulated by a curve fitting method. However, a half value transition temperture obtained in that method has no physical meaning. Dynamic J sub(ID) is larger than a static J sub(IC) in the ductile fracture range in this study. This rise is proportional to the yield stress ratio #sigma#sub(yd)/#sigma#sub(y)(--1.2-1.3). It is found, therefore, that the ...

International Nuclear Information System (INIS)

Fretting wear test in room temperature water was performed to evaluate the wear coefficient of CANDU (CANadian Deuterium Uranium) steam generator (SG) tube material (Alloy 800) against 410 type martensitic stainless steels. The main focus is to compare the wear behaviors between Alloy 800 and Inconel 690. Test conditions are 10#approx#30N of normal load, 200#approx#450mm of sliding amplitude and 30Hz of frequency. The result indicated that the wear rate of Alloy 800 was higher than those of Inconel 690 at various test condition such as normal loads, sliding amplitudes etc. From the results of SEM observation, there was little evidence of plastic deformation layer that were dominantly formed on the worn surfaces of Inconel 690. Also, wear particles in Alloy 800 were released from contacting asperities deformed by severe plastic flow during fretting wear. Main cause of wear rate ...

Energy Technology Data Exchange (ETDEWEB)

Location of transmission line faults are traditionally estimated by measuring the apparent impedance from a line terminal to the fault and converting the reactive component of the impedance to line length. None of the methods proposed to date address adequately the problems of fault location on distribution systems that have single or multiphase laterals and/or tapped loads. The research for this dissertation resulted in the development of a technique that estimates the location of a shunt fault on a radial distribution system that has several single and/or multiphase laterals. The technique takes into account load taps and non-homogeneity of the system, and has been tested for its ability to handle single-phase-to-ground, two-phase-to-ground, phase-to-phase and balanced three-phase faults. Computer simulations indicate that the technique is more accurate than the reactive component method. Results from a prototype of the ...

Energy Technology Data Exchange (ETDEWEB)

Optimal capacitor placement determines the size, type, and location of capacitors to be installed on a radial distribution feeder that will reduce peak power and energy losses while minimizing the costs of investment and installation of the capacitor banks. This paper describes a sensitivity-based optimal placement of capacitors that employs a new load characterization scheme using a voltage-current-angle-logger. The proposed method allows modeling of loads of different power factors for different portions of the distribution feeder. The optimal solution is obtained by testing various combinations of capacitor banks (based on the smallest bank size specified by the user) and candidate nodes along the distribution feeder, and calculating the resultant savings. In order to reduce solution time, the candidate nodes are ranked according to their sensitivity factors. The highest ranking nodes are considered first in the ...

Science.gov (United States)

The theory of a method of determination of reactivity from power spectral density measurements with /sup 252/Cf and the results of experiments with a critical assembly mockup of a liquid-metal fast breeder reactor (LMFBR) and with uranium (93.2 wt % /sup 235/U) metal cylinders and a sphere are presented. This method of reactivity determination has an advantage over existing methods in that it determines the reactivity only from properties of the reactor at the subcritical state of interest and thus does not require a calibration near delayed criticality. In these experiments, the reactivity was varied by changing the fissile loading or the amount of neutron absorber inserted; for the LMFBR mockup, the reactivity varied to approximately 75 dollars subcritical, and for the uranium metal assemblies to approximately 30 dollars subcritical. These experiments verified for the first time the predictions of theory that could be tested in the ...

International Nuclear Information System (INIS)

This standard provides requirements and guidelines for installation, inspection and testing activities that assure the quality of important mechanical parts of a nuclear power plant not covered by the ASME Boiler and Pressure Vessel Code, Section III, during construction. These parts include those mechanical systems and components whose satisfactory performance is required: for the plant to operate reliably; to prevent accidents that could cause undue risk to the health and safety of the public; or to mitigate the consequences of such accidents if they were to occur. The requirements of this standard deal with the protection and control necessary to assure that the requisite quality of those important parts of the plant are preserved from the time items are removed from storage or receiving until they are incorporated into the plant up to but not including fuel loading for PWR plants and the completion of cold functional ...

Energy Technology Data Exchange (ETDEWEB)

Various electrochemical capacitors (ultracapacitors) are being developed for hybrid vehicles as candidate power assist devices for the fast response engine. The primary functions of the ultracapacitor are to level the dynamic power loads on the primary propulsion device and recover available energy from regenerative breaking during off-peak power periods. Ultracapacitors show promise toward being able to accept high regenerative pulses while exhibiting very high cycle life. This paper will present test data from selected US Department of Energy (DOE) supported ultracapacitor projects designed to meet the fast response engine requirements. Devices containing carbon, conducting polymers, and metal oxide electrode materials in combination with aqueous or organic electrolytes are being supported by the DOE. This paper will present and discuss testing data obtained from recent prototype capacitors supplied by Maxwell Energy ...

Energy Technology Data Exchange (ETDEWEB)

An Allis-Chalmers, Model 2900, turbocharged diesel engine was converted to a dual-fuel engine in which ethyl alcohol was fumigated between the turbocharger and the intake manifold, and the diesel fuel was injected normally at a reduced rate. Tests were performed to determine if crankcase oil dilution that had occurred was caused by the following independent parameters: proof of the ethyl alcohol, crankcase oil temperature, engine load at maximum torque speed, and percentage of total energy in the form of ethyl alcohol. Engine tests were steady state for six hours, after which the crankcase oil was sampled for American Society for Testing and Materials (ASTM) laboratory tests for determination of flash points and fire points, water by centrifuge, water by distillation, and viscosity at room temperature. Results indicate a decrease in thermal efficiency and an increase in exhaust ...

Energy Technology Data Exchange (ETDEWEB)

Blade fatigue life is an important element in determining the economic viability of the Vertical-Axis Wind Turbine (VAWT). A principal source of blade fatigue is thought to be the stochastic (i.e., random) aerodynamic loads created by atmospheric turbulence. This report describes the theoretical background of the VAWT Stochastic Aerodynamic Loads (VAWT-SAL) computer code, whose purpose is to numerically simulate these random loads, given the rotor geometry, operating conditions, and assumed turbulence properties. A Double-Multiple-Stream Tube (DMST) analysis is employed to model the rotor's aerodynamic response. The analysis includes the effects of Reynolds number variations, different airfoil sections and chord lengths along the blade span, and an empirical model for dynamic stall effects. The mean ambient wind is assumed to have a shear profile which is described by either a power law or a logarithmic variation ...

Energy Technology Data Exchange (ETDEWEB)

This article presents the comparative bench testing results of a naturally aspirated, four stroke, four cylinder, water cooled, direct injection Diesel engine when running on diesel fuel and shale oil that is produced in Estonia from local oil shale. The purpose of this research is to investigate the possibility of practical usage of the shale oil as the alternative fuel for a high speed Diesel engine as well as to evaluate the combustion efficiency, brake specific fuel consumption, emission composition changes and the smoke opacity of the exhausts. Test results show that when fuelling a fully loaded engine with shale oil, the brake specific fuel consumption at the maximum torque and rated power is correspondingly higher by 12.3% and 20.4%. However, the brake thermal efficiencies do not differ widely and their maximum values remain equal to 0.36-0.37 for Diesel fuel and 0.32-0.33 for shale oil. The total nitrogen oxide ...

Science.gov (United States)

A comparative analysis between conventional passive twin tube dampers and skyhook-controlled magneto-rheological fluid (MRF) dampers for motorcycle front suspensions is provided, based on single axis testing in a damper test rig and suspension performance testing in road trials. Performance motorcycles, while boasting extremely light suspension components and competition-ready performance, have an inherent weakness in comfort, as the suspension systems are designed primarily for racing purposes. Front suspension acceleration and shock loading transmit directly through the front suspension triple clamp into the rider's arms and shoulders, causing rapid fatigue in shoulder muscles. Magneto-rheological fluid dampers and skyhook control systems offer an alternative to conventional sport motorcycle suspensions - both performance and comfort can be combined in the same package. Prototype MRF dampers designed ...

Energy Technology Data Exchange (ETDEWEB)

Full load (186 kW/cyl) operation using CWS fuel at 1050 rpm has been achieved on single cylinder GE-7FDL test engine. No major changes in engine parameters were made. With normal inlet air conditions, 3-5% pilot deisel fuel, separately injected or stratified into the main coal charge, was used. Inlet air temperature had to be raised about 40/sup 0/C if no pilot diesel fuel was used. The coal burnout was about 95% and the cycle efficiency was comparable to using diesel fuel. The NO/sub x/ and CO emissions were about 1/2 of those obtained normally with deisel fuel. The maximum heat release rate was higher than diesel fuel operation which resulted in higher maximum cylinder firing pressure. The combustion characteristic and its dependence on some fuel characteristics and inlet air parameters are discussed. Increasing coal burnout while limiting maximum cylinder firing pressure is the main objective of near future studies.

Energy Technology Data Exchange (ETDEWEB)

Na/S battery can have the higher energy density and higher power density than that of existing high performance secondary battery. This battery is expected to use for electric load leveling and electric vehicle. Ni/MH battery was developed in advanced countries, but it is one of the advanced technologies which are preserved in their own country. In the study on Na/S battery, properties of B{sup -}alumina electrolyte was investigated. Also the construction technologies of this test cell was established by combining tube type of B{sup -}alumina solid electrolyte with Na-, S- electrode etc. Especially of this cell, charge/discharge performance and open circuit voltage was examined. Mi/MH battery sample were tested with SBT500 system for self-discharge rate at room temp, was measured. It was found that the electrolyte and separator can be optimized to minimize the self-discharge rate. (author). refs., figs., tabs.

International Nuclear Information System (INIS)

The central feature of the Fast Flux Test Facility (FFTF) is the fast test reactor (FTR), which is a liquid-sodium-cooled fast reactor providing high fast-neutron flux for irradiation testing of fuels and materials. The FTR also provides a means to develop breeder reactor core components and to gain reactor systems operating experience for future liquid-metal fast breeder reactors (LMFBRs). In the FTR core, there are 82 incore positions (within rows 1 through 6) available for driver fuel assemblies and/or test assemblies. In addition, there are three safety rods and six control rods located in rows 3 and 5, respectively, in the three symmetric core sectors. The FFTF has been successfully and continuously operated for more than 11 reactor cycles. For the first 8 cycles, the core loadings were composed of the mixed-oxide driver fuel assemblies and some test ...

International Nuclear Information System (INIS)

We studied the niobium re-entrant cavity utilized by the Australian group in the Niobe gravitational wave detector. Instead of using their non-contact re-entrant cavity, we plan to change it to a closed one to be used in the parametric transducers of the Brazilian Mario Schenberg detector. The performance of the transducer depends on some cavity parameters such as the electrical Q and the electrical coupling. We measured the resonant frequency and the loaded electrical Q as a function of the probe position in a closed niobium #approx#15 GHz cavity operating at 4.2 K.

Energy Technology Data Exchange (ETDEWEB)

Coal-water-slurry (CWS) engine tests designed to evaluate a new accumulator-based injection system are described in this paper The new injection system was found to improve CWS burnout considerably at both full and part engine loads. The peak cylinder firing pressure when operating with CWS was no higher than when operating with diesel oil. These data demonstrates the improved engine performance that can be achieved with the accumulator-based injection system.

International Nuclear Information System (INIS)

Initial design parameters and early operational results of a 50 MeV high brightness electron linear accelerator are described. The system utilizes a radio frequency electron gun operating at a frequency of 2.856 GHz and a nominal output energy of 4.5 MeV followed by two, 2#pi#/3 mode, disc loaded, traveling wave accelerating sections. The gun cathode is photo excited with short (6 psec) laser pulses giving design peak currents of a few hundred amperes. The system will be utilized to carry out infra-red FEL studies and investigation of new high gradient accelerating structures.

International Nuclear Information System (INIS)

Nanoindentation was performed on a Mo-alloy single crystal to investigate effects of focused ion beam (FIB) milling on mechanical behavior. On a non-FIB-milled surface, pop-ins were observed on all load-displacement curves corresponding to a transition from elastic to plastic deformation. Similar pop-ins were not detected on surfaces subjected to FIB milling. This difference indicates that FIB milling introduces damage that obviates the need for dislocation nucleation during subsequent deformation. A second effect of FIB milling is that it increased the surface hardness. Together, these effects could be the source of the size effects reported in the literature on micropillar tests.

Energy Technology Data Exchange (ETDEWEB)

Stress-rupture strength tests were made of metal steam pipe (12Kh1MF steel) in various conditions, the original, after aging under laboratory conditions (580{degrees}C, 10,000 h), and after long service. It was shown that the more the steel is hardened by heat treatment or cold plastic working in the original condition, the less it hardens in creep. It was established that softening in creep of steel with a moderate yield strength is caused primarily by aging and with a high yield strength by pore formation.

Energy Technology Data Exchange (ETDEWEB)

In this paper, the control scheme of a liquefied petroleum gas (LPG)-diesel dual-fuel engine with electronic control is illustrated, the external characteristics and load characteristics of the LPG-diesel dual-fuel engine and the diesel engine are compared and analysed, and the results of automobile road tests are also given. The experimental results show that, compared with diesel, the output performance of dual fuel is not reduced, while smoke emission of dual fuel is significantly reduced, NO{sub x} emission of dual fuel is hardly changed, but HC emission and CO emission of dual fuel are increased and fuel consumption of dual fuel is reduced. (Author)

Energy Technology Data Exchange (ETDEWEB)

As a partner in this project, Siemens Power Generation investigated the crack propagation characteristics of short cracks in CMSX4. This involved crack propagation tests under dynamic and static load, creep tests on samples of different geometries, and life calculations, with the following results: No typical short cracking behaviour was observed under dynamic loads. Short crack propagation at 950 C under static load is well described by the fracture mechanical parameter C* integral. Notched bar creep tests showed longer times to cracking for notched bars. [German] In dem Verbundprojekt hat Siemens Power Generation u.a. die Untersuchungen von Rissausbreitungsverhalten von Kurzenrissen in CMSX4 als Hauptaufgabe bekommen. Dabei wurden Rissausbreitungsversuche unter dynamischer und statischer Belastung, Kriechversuche an Proben verschiedener Geometrie und ...

Energy Technology Data Exchange (ETDEWEB)

Non-edible filtered high viscous (72 cSt at 40{sup o}C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions ...

British Library Electronic Table of Contents (United Kingdom)

Free form fabrication and high resolution imaging techniques enable the creation of biomimetic tissue engineering scaffolds. A 3D CAD model of canine trabecular bone was produced via micro CT and exported to a fused deposition modeler, to produce polybutylene terephthalate (PBT) trabeculated scaffolds and four other scaffold groups of varying pore structures. The five scaffold groups were divided into subgroups (n=6) and compression tested at two load rates (49?N/s and 294?N/s). Two groups were soaked in a 25??C saline solution for 7?days before compression testing. Micro CT was used to compare porosity, connectivity density, and trabecular separation of each scaffold type to a canine trabecular bone sample. At 49?N/s the dry trabecular scaffolds had a compressive stiffness of 4.94?1.19?MP...

British Library Electronic Table of Contents (United Kingdom)

This experimental study investigates the effectiveness of crossed inclined bars (X-bars) as joint shear reinforcement in exterior reinforced concrete beam-column connections under cyclic deformations. Test results of 20 joint subassemblages with various reinforcement ratios and arrangements including X-bars in the joint area are presented. The X-type, non-conventional reinforcement is examined as the only joint reinforcement and in combination with common stirrups or vertical bars. The experimental results reported herein include full loading cycle curves, energy dissipation values and a categorization of the observed damage modes. Based on the comparisons between the overall hysteretic responses of the tested specimens, it is deduced that joints with X-bars exhibited enhanced cyclic perfo...

International Nuclear Information System (INIS)

The VNC2 and VNC5 steel tests on endurance were carried out in order to determine the capacity for work of large welded samples and to investigate the methods of welding. The samples made by the arc welding demonstrated the most high endurance at low frequencies of loading during the test of welded joints made of the VNC2 steel. The application of the VNC2 steel interlayers together with intermediate heat treatment allows one to increase the static and fatigue strength of welded joints at corresponding decrease of the construction weight during welding of the VNC5 steel as well as its combination with the VNC2 steels. The gas protection deterioration during steel welding leads to considerable diversity of values of endurance.

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.

Environmental Research Database

ObjectivesFirst comprehensive evaluation of the mechanical properties of an epoxy adhesive in different environments using a nano-indenter. ~%~~%~Use AFM/SEM and finite element modelling to generate knowledge of the precise mechanism of indentation in the epoxy adhesive. ~%~~%~Develop an improved data reduction algorithm for generating meaningful mechanical property data from indentation tests for adhesive materials.~%~ ~%~Validate the nano-indentation method of generating mechanical property data against [continued...]DescriptionThis project aims to address the problem of insufficient data on adhesive materials for effective modelling of joint behaviour in different environments. The methodology to be used is based on depth sensing indentation tests at different loads and rates and in different environments. Post-indentation deformation and recovery will be monitored by AFM and SEM and ...

International Nuclear Information System (INIS)

Over 300 cases of femoral neck fractures following radiotherapy for intrapelvic malignant tumor have been reported in various countries since Baensch reported this disease in 1927. In Japan, 40 cases or so have been reported, and cases of bilateral femoral neck fractures have not reached to ten cases. The authors experienced a case of 75 year-old female who received radiotherapy for cancer of the uterus, and suffered from right femoral neck fracture 3 months after and left femoral neck fracture one year and half after. As clinical symptoms, she had not previous history of trauma in bilateral femurs, but she complained of a pain in a hip joint and of gait disturbance. The pain in left femoral neck continued for about one month before fracture was recognized with roentgenogram. As histopathological findings, increase of fat marrow, decrease of bone trabeculae, and its marked degeneration were recognized. Proliferation of some blood vessels was found out, but ...

Science.gov (United States)

PMID:21807581

Science.gov (United States)

...2009-07-01 2009-07-01 false Loading and haulage equipment; operation. 77.1607 Section 77.1607...Loading and Haulage § 77.1607 Loading and haulage equipment; operation. (a) Vehicles shall follow...

Science.gov (United States)

...2010-07-01 2010-07-01 false Loading and haulage equipment; installations. 77.1605 Section 77.1605...Loading and Haulage § 77.1605 Loading and haulage equipment; installations. (a) Cab windows shall...

Energy Technology Data Exchange (ETDEWEB)

A study conducted at the IHS had the aim to obtain basic information on whether it is possible to build flow turbines following the free jet principle that are on a par with, or superior to, the conventional design, especially in terms of performance and the efficiency curve. Several inflow contours with a ventilated free jet and a conventional flow turbine were studied. The direct comparison of these variants revealed a slightly enhanced peak load efficiency and a very distinct superiority of the free jet contour during partial load. But the efficiency of all variants failed to attain the values claimed by commercial manufacturers. As compared to the initial contour, peak load efficiency was enhanced by 5 per cent. During partial load, the variants studied showed a distinct superiority of the free jet concept over the contour of conventional flow turbines. (orig.) [Deutsch] Am IHS wurde eine ...

Science.gov (United States)

The performance of intermolecular potential models on the adsorption of benzene on graphitized thermal carbon black at various temperatures is investigated. Two models contain only dispersive sites, whereas the other two models account explicitly for the dispersive and electrostatic sites. Using numerous data in the literature on benzene adsorption on graphitized thermal carbon black at various temperatures, we have found that the effect of surface mediation on interaction between adsorbed benzene molecules must be accounted for to describe correctly the adsorption isotherm as well as the isosteric heat. Among the two models with partial charges tested, the WSKS model of Wick et al. that has only six dispersive sites and three discrete partial charges is better than the very expensive all-atom model of Jorgensen and Severance. Adsorbed benzene molecules on graphitized thermal carbon black have a complex orientation with respect to distance from the surface and also ...

Energy Technology Data Exchange (ETDEWEB)

The durability of ball bearings, 32-mm- and 45-mm-bore, with a retainer or glass cloth-polytetrafluoroethylene (PTFE) laminate was tested under a high radial load at a speed of 20,000 rpm in LOX or LN2. The retainers were characterized as good self-lubricators because the abrasive glass-cloth fiber tips exposed on the retainer were chemicaly etched away with hydrofluoric acid (HF). During testing, the bearing-cartridge-acceleration was monitored to detect bearing damage. Testing in LOX for about 2.2 hr showed that excellent lubricating conditions were obtained for all bearings. Testing in LN2 for about 5.1 hr detected that the fatigue life of the bearing was about the same as the calculated B10 fatigue life. The HF chemical treatment resulted in a reacted fluoride-oxide material which remained in the etched part of the glass fiber. Several chemical products, particularly MgO, CaO, ...

Energy Technology Data Exchange (ETDEWEB)

The use of excitation system controls, specifically the Power System Stabilizer (PSS), to improve damping of power system oscillations and thus extend steady-state stability limits has been a subject of great interest in recent years. The desire to more fully utilize transmission capacity led to the installation of PSS controls on greater numbers of generating units to maintain stability margins. This paper addresses the tuning and adjustment of PSS controls in a two unit power plant. Both analytical studies and field test confirmations are presented. The practical difficulties of verifying the PSS control loop gain margin by testing are explored. A simplified procedure is outlined. The Lower Colorado River Authority (LCRA), Fayette Power Project (FPP) consists of two 683.7 MVA tandem compound steam turbine driven generators. The excitation systems are of the alternator rectifier type and the PSS control utilizes shaft speed as an input signal. ...

Energy Technology Data Exchange (ETDEWEB)

In 1976, the US Department of Energy and New York State - ERDA granted a contract for the development of a +-600 kV dc underground transmission cable system looking to inevitable future requirements in the US for economic, high-capacity, long-distance underground transmission linking remote generating stations to metropolitan load centers. This project was comprehensive and dealt with three separate system components, i.e., cable, splice, and terminals. In each instance, for each component, development required an intensive R and D effort, focused on the following categories: insulating materials, model testing, design of full-scale prototype, manufacturer of prototype, and laboratory development testing. Insulating papers and oils were selected, and model studies performed, for both self-contained type and pipe type oil-filled cables. However, only the pipe cable design was finally designated for full-size cable ...

Energy Technology Data Exchange (ETDEWEB)

This R and D project is planed to supply domestic demands of Mo-99 through fission route, and consequently this project will be expected to rise up utilization of HANARO and KAERI's capability for marketing extension into domestic and oversea radiopharmaceutical market. HEU and LEU target types are decided and designed for fission Mo-99 production in domestic. Experimental study of target fabrication technology was performed and developed processing equipments. And conceptual design of target loading/unloading in/from HANARO device are performed. Tracer test of Mo-99 separation and purification process was performed, test results reach to Mo-99 recovery yield above 80% and decontamination factor above 1600. Combined Mo-99 separation and purification process was decided for hot test scheduled from next year, and performance test was performed. Conceptual design for ...

Energy Technology Data Exchange (ETDEWEB)

The thermomechanical behaviour of clayey soils was examined in a laboratory study because of their importance in some engineering applications such as hydrocarbon extraction from oil-bearing sands and radioactive waste disposal. The slightest temperature variations have been known to have an impact on the mechanical behaviour of clayey soils. In this study, tests were conducted on reconstituted and natural clayey soils using triaxial cells modified to control temperatures. Changes of temperature and stress state were not applied simultaneously. Instead, the tests were divided into two separate sections aimed at studying the thermal and mechanical behaviour of clays. The thermal behaviour tests examined the deformations induced by drainage temperature changes as well as pore-pressure generation and consolidation phenomena. The mechanical behaviour tests, focused on the influence of temperature and ...

Energy Technology Data Exchange (ETDEWEB)

The Minami-Iwaki trunk line now under construction by Tokyo Electric Power Company is an UHV transmission line which covers 130km from the central region of the Abukuma highlands, Fukushima Prefecture, through the northern ridge of the Kanto Plain to Imaichi City, Tochigi Prefecture and has 235 steel towers. About 30% of the ground along the above route is mainly layers of sand and gravel. Accordingly it has become urgent to design rationally the pile foundations in the sand and gravel layers. Hence the company has studied an estimation method of the ultimate bearing power of cast-in-place piles penetrating the sand and gravel layers and the displacement of pile heads. In this report, the result of the above study is described. The company has so far used the equations in accordance to the Meyerhof equations for the estimations of the ultimate bearing power and this time, this equations have been examined for its application to the sand and gravel layers, and for designing the steel ...

Science.gov (United States)

Polymer matrix composites are presently used in many fields due to their excellent mechanical properties such as high specific strength and stiffness. However, not much is known of these composites' response to impact loading, which usually occurs at strain rates much higher than the strain rates used to measure the quasi-static mechanical properties of materials. The use of static properties in the study of structures that undergo dynamic loading can produce excessive design weight or cause unexplained and untimely failure. The studies included in this dissertation provide the results of Split Hopkinson Pressure Bar experiments to determine the ultimate compressive strength and strain of composites at high strain rates. Most researchers are using specimens with different dimensions and geometry. For this reason, it is difficult to compare results of tests done by different people. Herein, the Split Hopkinson Pressure Bar ...

Science.gov (United States)

The effect of aerosol on clouds poses one of the largest uncertainties in estimating the anthropogenic contribution to climate change. Small human-induced perturbations to cloud characteristics via aerosol pathways can create a change in the top-of-atmosphere radiative forcing of hundreds of Wm-2. Here we focus on links between aerosol and deep convective clouds of the Atlantic and Pacific Intertropical Convergence Zones, noting that the aerosol environment in each region is entirely different. The tops of these vertically developed clouds consisting of mostly ice can reach high levels of the atmosphere, overshooting the lower stratosphere and reaching altitudes greater than 16 km. We show a link between aerosol, clouds and the free atmosphere wind profile that can change the magnitude and sign of the overall climate radiative forcing. We find that increased aerosol loading is associated with taller cloud towers and anvils. The taller clouds reach levels of ...

Energy Technology Data Exchange (ETDEWEB)

Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were either filled with air or with a molten mixture of sodium nitrate, potassium nitrate and an oxidizer. Low-cycle fatigue tests were carried out at 1200/sup 0/F and 650/sup 0/F by cycling the strain continuously between equal mangitude of tensile and compressive values at a rate of 4 x 10/sup -3/sec/sup -1/ until failure. The creep-fatigue tests were carried out at 1200/sup 0/F. The loading cycle differed from that of low-cycle fatigue testing only in the imposition of a hold at the peak compressive strain in each cycle. Cracks always initiated on the inner surface of the hollow specimen, and therefore, corrosive effects on crack propagation and initiation were controlled by the environment within the specimen cavity. In common with tests carried out ...

Energy Technology Data Exchange (ETDEWEB)

Urea-formaldehyde resin bonded particle board, medium density fiberboard and plywood paneling are used as flooring, wall paneling, for cabinet work and in furniture, and are present in almost every office, home and public building. If large quantities of these products are used in poorly ventilated spaces, high manufacturing quality control is necessary to avoid problems of latent formaldehyde release. Indoor air formaldehyde concentrations depend on the nature of the product, the product surface to air volume (loading) factor, temperature, humidity, age and product emission rates. Standard test methods are now available for measuring product emission rates that make it possible to predict the performance of UF-bonded pressed wood materials if use conditions and environmental parameters are known. Recent modifications in adhesive and board manufacturing parameters have made it possible to reduce formaldehyde emission significantly, and ...

Energy Technology Data Exchange (ETDEWEB)

A cooling system was developed which could be used even in such areas where the maximum and minimum temperatures of a day might differ widely. The system features in that a latent heat storage unit is connected to the natural circulation cooling unit consisting of 2 heat exchangers where condensed gas (refrigerant) which performs gas-liquid change has been sealed, enabling to cool objects night and day without the requirement for any power source. Electronic equipment was installed in an insulated shelter. Lauric acid and refrigerant R-22 were used as the latent heat storage medium and the heat transport medium respectively. Natural convection heat transfer performance of the outside surfaces of the condenser and the evaporator and the transient behavior of the system during the melting and solidification periods of the latent heat storage medium were tested. As a result of a 48 hour simulation experiment with load conditions set basing on the ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a PEM fuel cell. The analysis of this process requires determination of the effective thermal conductivity as well as the thermal contact resistance associated with the interface between the GDL and adjacent surfaces/layers. In the present study, a custom-made test bed that allows the separation of effective thermal conductivity and thermal contact resistance in GDLs under vacuum and ambient conditions is described. Measurements under varying compressive loads are performed using Toray carbon paper samples with a porosity of 78% for a range of thicknesses. The measurements are complemented by compact analytical models that achieve good agreement with experimental data. A key finding is that thermal contact resistance is the dominant component of the total thermal resistance; neglecting this phenomenon may result in significant errors in ...

British Library Electronic Table of Contents (United Kingdom)

Empty palm fruit bunch fiber (EPFBF), a readily available cellulosic biomass from palm processing facilities, is investigated as a potential carbohydrate source for cellulosic ethanol production. This feedstock was pretreated using ammonia fiber expansion (AFEX) and enzymatically hydrolyzed. The best tested AFEX conditions were at 135??C, 45?min retention time, water to dry biomass loading of 1:1 (weight ratio), and ammonia to dry biomass loading of 1:1 (weight ratio). The particle size of the pretreated biomass was reduced post-AFEX. The optimized enzyme formulation consists of Accellerase (84??L/g biomass), Multifect Xylanase (31??L/g biomass), and Multifect Pectinase (24??L/g biomass). This mixture achieved close to 90% of the total maximum yield within 72?h of enzymatic hydrolysis. Fer...

Energy Technology Data Exchange (ETDEWEB)

This disclosure provides a solar rechargeable aircraft that is inexpensive to produce, is steerable, and can remain airborne almost indefinitely. The preferred aircraft is a span-loaded flying wing, having no fuselage or rudder. Travelling at relatively slow speeds, and having a two-hundred foot wingspan that mounts photovoltaic cells on most all of the wing`s top surface, the aircraft uses only differential thrust of its eight propellers to turn. Each of five sections of the wing has one or more engines and photovoltaic arrays, and produces its own lift independent of the other sections, to avoid loading them. Five two-sided photovoltaic arrays, in all, are mounted on the wing, and receive photovoltaic energy both incident on top of the wing, and which is incident also from below, through a bottom, transparent surface. The aircraft is capable of a top speed of about ninety miles per hour, which enables the aircraft to attain and can ...

Energy Technology Data Exchange (ETDEWEB)

Heat exchangers for high and ultrahigh temperatures are a need and a precondition to realise high efficient fossil fired power plants based on the so-called Externally Fired Combined Cycle (EFCC) or the Indirect Fired Gas Turbines (IFGT). The main target of both processes is to increase the thermal efficiency of existing power plants by approximately 25% resulting in the same decrease in fuel consumption and, therefore, in the same reduction of CO{sub 2} formation. The main activities of the MPA University of Stuttgart in this project is focused on the characterisation and qualification of the structural material of the ultrahigh temperature heat exchanger (UHTHE) necessary in the above mentioned processes. The influence of the temperature and load on the material behaviour have been analysed by means of tensile tests and creep tests. The effectiveness of different coating systems and the interaction between coating system ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes work performed by Argonne National Laboratory on fatigue and environmentally assisted cracking (EAC) in light water reactors from January 1997 to June 1997. Topics that have been investigated include (a) fatigue of carbon, low-alloy, and austenitic stainless steels (SSs) used in reactor piping and pressure vessels, (b) irradiation-assisted stress corrosion cracking of Types 304 and 304L SS, and (c) EAC of Alloys 600 and 690. Fatigue tests were conducted on ferritic and austenitic SSs in water that contained various concentrations of dissolved oxygen (DO) to determine whether a slow strain rate applied during various portions of a tensile-loading cycle is equally effective in decreasing fatigue life. Slow-strain-rate-tensile tests were conducted in simulated boiling water reactor (BWR) water at 288 C on SS specimens irradiated to a low fluence in the Halden reactor and the results were compared with ...

Energy Technology Data Exchange (ETDEWEB)

Chromium containing amorphous hydrogenated carbon films (a-C : H/Cr) have been prepared by simultaneous rf plasma activated chemical vapour deposition of methane and magnetron sputtering of a chromium target. During deposition the substrates were heated (up to 300C) and DC biased (-200 and -600 V) in order to obtain films with high chemical stability. Constant temperature tests were performed at 250C in air with coatings deposited on silicon substrates. The degradation of the coatings was monitored by Raman spectroscopy and reflectance and transmission measurements. The main degradation mechanisms are discussed and the relevant parameters which improve the durability of the coatings are presented. Furthermore, the durability of solar selective, multilayered coatings which were deposited on copper sheets was investigated. Based on accelerated aging tests at different temperature loads in air (at 220C, 250C and 300C) and in a ...

Energy Technology Data Exchange (ETDEWEB)

The instrument ball bearings are the key components of movable components for various kinds of measuring and control instruments; they often operate in the environmental condition of high-speed and light preload. In general, the non metal, disposable oilimpregnated retainer material has been used for these kinds of high precision miniature bearing. The engineering practice shows that the common failure mode of them is the wear which appears under the condition of insufficient lubrication condition. As the results, the vibration and noise will be enlarged, so does the frictional torque, which makes the ball bearings to lose its original working accuracy. It is the lifetime test of bearings that can enable the designers and manufacturers to chose the material of the bearing properly, optimize the product structure, mend the manufacturing technique process, and to enhance the technical level of the bearing products significantly. In this paper, the wear lifetime ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the basic principles underlying the operation of low heat loss engines and the magnitude of the efficiency improvements that are theoretically achievable. The effect of varying degrees of thermal insulation on various operating parameters is examined in some detail, as is the relationship between degree of insulation and ceramic coating thickness. The effect on ceramic materials of severe surface temperature oscillations and the resultant thermal stress gradients is also discussed. In the following section, the paper describes methods of construction adopted both for ceramic inserts and coatings, and rig tests for the assessment of thermal fatigue under both load and firing cycling. The paper does not attempt to draw any general conclusions.

Energy Technology Data Exchange (ETDEWEB)

The texture influence on tensile tests of AZ31, one of the common Mg alloys, has been studied. Starting material was a rectangular extruded bar, which has a strong texture. Due to the preparation of three tensile samples with 0 , 45 , 90 to the extrusion direction, the initial bar texture influences differently on the mechanical behaviour under tensile load. This results in a variation of the yield strength (90 MPa and 175 MPa) the ultimate tensile strength (250 MPa - 278 MPa) and the final texture. Experimental texture analysis was completed by texture simulations using the VPSC-model (visco plastic self-consistent). The good agreement between experimental and simulated pole figures allows the determination of the activated deformation modes related to the initial texture. (orig.)

Energy Technology Data Exchange (ETDEWEB)

BC Hydro has been assessing and upgrading its facilities and implementing response alternatives to potential damage resulting from a major earthquake. This paper reviews the utility`s seismic evaluation of its overhead transmission system, focusing on the Lower Mainland area where most of the tall critical river-crossing towers are located. The paper gives an overview of the geologic environment of the Lower Mainland and outlines the criteria used for assessing existing structures for their ability to withstand design seismic loads. It then describes the investigation and analysis methods used in the assessment, including geotechnical field tests, ground response analysis, determination of soil liquefaction potential, and dynamic analysis of structures and piles. Options for seismic upgrades are discussed and illustrated by the case of the Pitt River crossing, where tower foundations were reinforced with steel pipe piles.

British Library Electronic Table of Contents (United Kingdom)

Objective.The objective of this study was to use the newly synthesized poly(quaternary ammonium salt) (PQAS)-containing polyacid to formulate the light-curable glass-ionomer cements and study the effect of the PQAS on the compressive strength and antibacterial activity of the formed cements.Materials and methods.The functional QAS and their constructed PQAS were synthesized, characterized and formulated into the experimental high-strength cements. Compressive strength (CS) and Streptococcus mutans viability were used to evaluate the mechanical strength and antibacterial activity of the cements. Fuji II LC cement was used as control. The specimens were conditioned in distilled water at 37 degrees C for 24 h prior to testing. The effects of the substitute chain length, loading as well as gra...

Energy Technology Data Exchange (ETDEWEB)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 ..mu..m; drops of diameter size 1.5 ..mu..m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols from the washing water.

Energy Technology Data Exchange (ETDEWEB)

The performance of the gaseous fuel supply and its influence on hydrocarbon (HC) emissions of dual-fuel engines have been investigated. A new design of manifold respirators with mixers is also presented in the paper. The design of the gaseous fuel supply system has a great influence on HC emissions in the dual-fuel engine at light load. The problem of scavenging is discussed and solved by using the manifold respirators in the dual-fuel engine. It performs the function of retarding the gaseous fuel entry timing from the moment of intake valve opening, and its delaying effects have been measured and tested. Experimental results show that the manifold respirator gives the best performance in reducing HC emissions compared with a common pipe mixer and a respirator with bo miser. In addition, the mixing effects are sensitive to the mixer configuration. (Author)

International Nuclear Information System (INIS)

This article describes the project for the installation of an additional emergency diesel generator in both Asco and Vandellos NPPs. The basic objectives of this project are to improve the availability of the emergency generation system, in order to provide greater ability to address potential contingencies, and also to increase the flexibility of the preventive periodic maintenance of the emergency diesel generators. This maintenance, that is currently a milestone of the critical path of the refueling outage, will be performed on-line. The new diesel generator will be sized to support all the loads considered in the safety case and also the consumption of its own auxiliary systems, and will be tested for operability assessment on the same periodical basis than the existing ones. The solution adopted will also permit that the N diesel generator may be connected to any bus bar class 1E in a station black-out scenario. (Author)

International Nuclear Information System (INIS)

Up to 90% of the life time of cyclically loaded components is determined by short crack initiation and propagation. This stage of the fatigue damage process is strongly influenced by microstructural features, e.g. grain boundaries and crystallographic grain orientation. Therefore LEFM can not be applied in a reasonable manner explaining the demand for a mechanism-related modelling method. The present study deals with mechanical testing and microstructural examinations applied to the relatively new #beta#-titanium alloy LCB. The results are used as data base to develop a new short crack model that is based on the model of Navarro and de los Rios. By using various techniques such as electron back-scattered diffraction and finite-element calculations the origin of crack initiation is revealed and the characteristics of crack propagation is determined. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The engine performance test was studied at high load in a small direct injection diesel engine by measuring fuel spray travel of three nozzles having different nozzle length/nozzle diameter(L/D) and by changing parameters such as piston cavity diameter and intake swirl. Hydrocarbon(HC) and the brake specific fuel comsumption(BSFC) were mainly influenced by spray characteristics due to L/D compared with piston cavity diameter and intake swirl. The piston cavity diameter optimal to BSFC corresponds to the fuel spray travel(fuel penetration) in each nozzle. The exhaust smoke was improved by reducing piston cavity diameter and by promoting the intake swirl. NOx increased with the decrease of piston cavity diameter at the identical nozzle and also increased in case of larger piston cavity diameter owing to the utilization of intense spray penetration. (13 figs, 4 refs)

Energy Technology Data Exchange (ETDEWEB)

The effects of antimony addition on the microstructures and creep behavior of AZ31 have been studied. Constant load creep tests were carried out at 200 C and an initial stress of 50MPa for AZ31 alloys containing antimony up to 0.84% by weight. Results show that Small additions of antimony to AZ31 effectively decreased the creep extension and steady state creep rates. The steady state creep rate of AZ31 was reduced 2.5 times by the addition of 0.84% of antimony by weight. The main reason for the higher creep resistance is due to the presence of high volume fraction ({proportional_to} 20%) of second phases including Mg{sub 3}Sb{sub 2}, which effectively hindered the movement of dislocations during the elevated temperature creep. (orig.)

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

British Library Electronic Table of Contents (United Kingdom)

Superalloys, such as Inconels and Incoloys, are extensively used where high strength is a requirement. However, where these materials are required to slide against one another, particularly with poor or no lubrication, high friction levels and seizure are commonly seen to occur, which can cause component failure. In this work seizure characteristics of three superalloys (Inconel 718 and Incoloys 945 and 945X) were investigated, uncoated, coated with Armoloy (a hard, thin, dense chrome coating with a micro-nodular surface texture) and plasma nitrided in dry sliding conditions. A rig purpose built for initiating seizure was used. It involves sliding a ball against a disc at constant speed while the load is increased. Tests are designed to last less than one rotation so that the wear scar can...

Energy Technology Data Exchange (ETDEWEB)

The performance of advanced ceramics under cavitation loading in distilled water was studied by using a laboratory test with vibration-induced cavitation following the pattern of the ASTM standard G32-92. The hardened and tempered martensitic steel 100Cr6 was used as a reference. The aim was to identify mechanisms and the effects of important microstructural parameters on damage of polished Al{sub 2}O{sub 3}, Al{sub 2}O{sub 3}-ZrO{sub 2}, ZrO{sub 2} and SiC ceramics. Results showed that surface damage of brittle ceramics was mainly dominated by intergranular fracture, followed by detachment of single grains or fragments of them. Both incubation time and erosion rate were affected by the amount of initial surface cavities, grain sizes and secondary phases at grain boundaries. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A multi-zone computational model in conjunction with some engine tests are used to examine the combustion process of gas fueled diesel engines common known as dual fuel engine to provide information about details of the production of exhaust emissions, especially at light load when very lean mixtures are employed. Detailed chemical reaction kinetic simulation is employed for each of these individual combustion zones so as to establish the associated temporal variations in the concentrations of reacting species right to the exhaust stage. The influence of changes in major operating and design parameters such as the concentration of the gaseous fuel in the cylinder charge, intake temperature and the size of the diesel pilot fuel employed on the production of the exhaust emissions are examined. It is demonstrated in general that any measure that tends to increase the size of the combustion regions within the overly lean cylinder charge will reduce ...

Energy Technology Data Exchange (ETDEWEB)

Adsorption by activated red mud (ARM) is investigated as a possible alternative to the conventional methods of Cr(VI) removal from aqueous synthetic solutions and industrial effluents. Adsorption characteristics suggest the heterogenous nature of the adsorbent surface sites with respect to the energy of adsorption. Various factors such as pH, contact time, Cr(VI) concentration, amount of adsorbent, and temperature are taken into account, and promising results are obtained. The applicability of the Langmuir as well as Freundlich adsorption isotherms for the present system is tested. The loading factor (i.e., milligrams Cr(VI) adsorbed per gram of ARM) increased with initial Cr(VI) concentration, whereas a negative trend was observed with increasing temperature. The influence of the addition of anions on the adsorption of Cr(VI) depends on the relative affinity of the anions for the surface and the relative concentrations of the anions.

Energy Technology Data Exchange (ETDEWEB)

The following subjects were discussed at the conference: Stability of welded joints, creep stress in CrMo steels, life prediction, developments in modern power plant steels, testing, calculation of deformation, crack propagation and crack analysis under complex loads. [German] Die Autoren der Tagung referieren ueber folgende Themen: Stabilitaet von Schweissverbindungen, Kriechbeanspruchung von Chrom-Molybdaen Staehlen, Lebensdauervorhersage, Entwicklungen fuer die Anwendung in modernen Kraftwerken, Prueftechnik, Berechnung von Verformung, Rissentwicklung und -bewertung bei komplexer Beanspruchung. (uke)

Energy Technology Data Exchange (ETDEWEB)

The surface of low alloy steel (En40B) has been engineered in the plasma of a glow discharge via plasma nitriding and ion plating of titanium nitride (TiN) coatings on the nitrided substrates with the purpose of enhancing the surface properties and fatigue strength. The nitriding response of the steel has been accessed by the evaluation of phase composition, layer thickness, hardness profile, residual stresses and nitrogen and carbon distributions. The wear and fatigue characteristics of the plasma-nitrided steel have been investigated and simple models have been developed to describe the influence of such properties as depth and strength of the nitrided case on the fatigue limit and load-bearing capacity of the nitrided steel. In order to further improve the tribological properties and load-bearing capacity of the low alloy steel, a duplex plasma surface-engineering technique has been developed. This is achieved by plasma nitriding the steel ...

Energy Technology Data Exchange (ETDEWEB)

Rhodium (Rh) is a critical component of current automotive three-way catalysts (TWCs), particularly with regard to NO{sub x} and CO conversion at rich and stoichiometric air-fuel ratios (A/F). Rh supported on CeO{sub 2} was active for NO{sub x} and CO conversions but could be deactivated easily by high temperature aging. The cause of the deactivation is ascribed to the sintering of CeO{sub 2}. ZrO{sub 2} incorporation into CeO{sub 2} is reported to have high thermal durability in terms of oxygen storage capacity (OSC). There has been no report showing direct experimental evidence that Rh-loaded on CeO{sub 2}-ZrO{sub 2} mixed oxides induced effects on TWC performance improvement in the actual automotive exhaust. In the present paper, the Rh-CeO{sub 2} interaction contributing to NO{sub x} reduction and the catalytic behavior of Rh-loaded CeO{sub 2}-ZrO{sub 2} mixed oxide is addressed. Incorporating CeO{sub 2}-ZrO{sub 2} into a catalyst offered ...

UK PubMed Central (United Kingdom)

Most mechanical forces acting on the skeleton are generated either through impact with the ground (i.e., gravitational loading) or through muscle contractions (i.e., muscle loading). If one...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this paper an attempt is made to forecast load using fuzzy neural network (FNN) for an integrated power system. Here, the proposed system uses a two stage FNN for a short term peak and average load forecasting (STPALF). The first stage FNN deals with the load forecasting and the second stage algorithm can be worked independently for network security. This technique is used to forecast load accurately on week days as well as holidays, weekends and some special occasions considering historical data of load and weather information and also take necessary control action for network security.

Science.gov (United States)

... Accession Number : ADD431225. Title : Influence of Fiber Loading on Thermal Ablation of PTFE,. Corporate Author : Personal Author(s) : Letson,KN. ...

Energy Technology Data Exchange (ETDEWEB)

This document is the annual update of the FFTF and Advanced Reactors Transition Program Resource Loaded Schedule for FY 2002 using current project direction and authorized funding levels

Energy Technology Data Exchange (ETDEWEB)

Recent Canadian progress in the development of the curved-blade Darrieus vertical-axis wind turbine (VAWT) is described. Cooperation between government, industry and power utilities in the conduct of field trials, over several years, has demonstrated improved performance and reliability of grid-coupled turbines of this type. The rated power of the VAWTs currently under test ranges from 30 kW, in a wind/diesel powerplant, to 230 kW, in an installation on an island in the Gulf of St. Lawrence. Progress has also been made in understanding the basic aerodynamic behavior of the VAWT and theoretical methods for performance and load prediction have correspondingly improved. A brief description is given of Project EOLE, a cooperative project between the federal government and the utility Hydro-Quebec to develop and test, during the next two to three years, a 4 MW VAWT prototype, which will be coupled to the power grid at a location ...

International Nuclear Information System (INIS)

During the operation of a tokamak, the first wall elements suffer very high heat fluxes. Heat is removed by internal cooling by means of water, helium or fluid metal. The resulting inhomogeneous temperature field cause internal stresses which, due to the pulsed operation are of cyclic nature. Additional mechanical stresses in the first wall may be caused by disruptions or vertical plasma movements. During theses events high currents are induced in the metallic part of the first wall which by their interaction with the magnetic field of the tokamak lead to mechanical forces. These electromechanical stresses may lie beyond the yield stress of the structural material. From the interaction of thermal and mechanical forces, a complex stress state is achieved which under certain circumstances may lead to premature failure and/or to progressive plastic deformations (ratcheting). In order to study the boundary conditions for the occurrence of ratcheting, a testing rig has ...

International Nuclear Information System (INIS)

This study describes the mechanical compatibility of the direct use of spent pressurized water reactor (PWR) fuel in Canada deuterium uranium (CANDU) reactors (DUPIC) fuel, when it is loaded into a CANDU reactor. The mechanical compatibility can be assessed for the fuel management, primary heat transport system, fuel channel, and the fuel handling system in the reactor core by both the experimental and analytic methods. Because the physical dimensions of the DUPIC fuel bundle adopt the CANDU flexible (CANFLEX) fuel bundle design which has already been demonstrated for a commercial use in CANDU reactors, the experimental compatibility analyses focused on the generation of material property data and the irradiation tests of the DUPIC fuel, which are used for the computational analysis. The intermediate results of the mechanical compatibility analysis have shown that the integrity of the DUPIC fuel is mostly maintained under the high power and ...

International Nuclear Information System (INIS)

We have already developed three conventional and one periodic permanent (PPM) type 50-MW class klystrons, a smart modulator, and the first HOM-free accelerator structure (Choke-mode type, full-scale high power model). A very stable ceramic high voltage monitor was successfully tested up to 367-kV with a 4.5-#mu#sec pulse. A new C-band SiC type high power rf-load, advancing the power handling capability up to 50-MW is now being designed. It should have excellent mass production characteristics as it uses circularly symmetric TM_0_1_1 chained cavities. The first high power prototype of an rf compressor cavity made of a low thermal expansion material (super Invar) was designed to provide stable operation even with a very high Q of 200-k, it was successfully tested the output rf power up to 135-MW, 0.5-#mu#sec pulse width and 50-pps repetition rate. The C-band linac rf-system will be used for the SASE-FEL (SCSS) production ...

Energy Technology Data Exchange (ETDEWEB)

This is a report on modification of a locomotive diesel engine to a dual-fuel engine to determine if the dual fuel engine in railway service will provide high performance, lower fuel and maintenance costs. After the locomotive was modified and the new governor and linkage were installed by General Motors at the BN's Northtown Diesel Shop near Minneapolis, the locomotive went through startup procedures. General Motors participated in startup. Some calibration, adjustments and minor piping changes were required but in general the problems encountered in startups were quite insignificant. The locomotive was connected to the load box (static test) during startup and at 720 RPM exceeded the required output for this test as established by the parties. Operation on straight oil over the range from idle through No. 8 throttle notch and on dual fuel from No. 5 through No. 8 throttle notch was smooth as was the transfer from ...

International Nuclear Information System (INIS)

Purpose: To evaluate the effect on dilatation of three types of covering materials used for endovascular stent-grafts.Methods: Stent-grafts with three types of covering material [0.1-mm polytetrafluoroethylene (PTFE), 0.2-mm PTFE, and 0.15-mm woven polyester] were placed in a fluid circuit. For the pulsatile pressure test, the luminal pressure of 190/130 mmHg was loaded up to 300,000 pulses. For the static pressure test, the luminal pressure was increased from 50 to 300 mmHg at 50-mmHg increments. The percent of dilatation of each stent-graft was compared.Results: The 0.1-mm PTFE stent-graft was significantly more dilated than the 0.2-mm PTFE and the 0.15-mm woven polyester stent-graft (p < 0.005) in both examinations. There was no significant difference between the 0.2-mm PTFE and the 0.15-mm woven polyester stent-grafts. The dilatation of the 0.1-mm PTFE stent-graft was irreversible.Conclusion: The 0.15-mm woven ...

Energy Technology Data Exchange (ETDEWEB)

The design of high level radioactive waste (HLW) repositories in deep geological media in which bentonite clay is proposed as a sealing material leads to the need of further studying the behaviour of highly compacted expansive soils when subjected to mechanical, hydraulic and thermal changes. Laboratory tests may help to understand the processes that take place in the clay barrier under simple and controlled conditions and to develop the governing equations. The laboratory tests enable to isolate the different processes, making their interpretation easier, and provide with fundamental data concerning the parameters to be used in the models. The extremely low permeability of these materials, their avidity for water (high suction) and their high swelling capacity make necessary the modification of the conventional laboratory techniques and procedures to determine basic physical parameters. The main hydraulic properties of the barrier to be ...

Energy Technology Data Exchange (ETDEWEB)

A new package for the air transport of hazardous materials is currently being developed in the Transportation Systems Department at Sandia National Laboratories. The baseline design has a unique impact limiter which uses layers of aluminum screen wire and aramid cloth fabric. A primary motivation for selecting this unusual combination of materials is the need for the impact limiter to not only limit the amount of load transmitted to the primary container but also remain in place during impact events so that it provides a thermal barrier during a subsequent fire. A series of uniaxial and confined compression tests indicated that the layered material does not behave like other well characterized materials. No existing constitutive models were able to satisfactorily capture the behavior of the layered material; thus, a new plasticity model was developed. The new material model was then used to characterize the response of air transport packages ...

International Nuclear Information System (INIS)

This report describes the development of solidification systems for sodium nitrate waste. Sodium nitrate waste was solidified in the polymers polyethylene, polyester-styrene (PES), and water-extendible polyester-styrene (WEP). Evaluations were made of the properties of waste forms containing various amounts of sodium nitrate by leaching immersion in water, measuring compressive strengths and by the EPA Extraction Procedure. Results of the leaching test are presented as cumulative fraction leached (CFL), incremental leaching rate, and average leaching indices (LI). For waste forms containing 30 to 70 wt% sodium nitrate, the CFL ranged from 9.0 x 10"-"3 to 7.3 x 10"-"1 and the LI from 11 to 7.8. After ninety days immersion in water, the compressive strengths ranged from 720 psi to 2550 psi. The nitrate releases from these samples using the EPA Extraction Procedure were below 500 ppM. The nitrate releases from PES waste forms were similar to those from polyethylene ...

Science.gov (United States)

This project proposes to design and develop a new class of power converters (direct DC to AC) to drastically improve performance and optimize the cost, size, weight and volume of the DC to AC converter in SOFC systems. The proposed topologies employ a high frequency link; direct DC to AC conversion approach. The direct DC to AC conversion approach is more efficient and operates without an intermediate dc-link stage. The absence of the dc-link, results in the elimination of bulky, aluminum electrolytic capacitors, which in turn leads to a reduction in the cost, volume, size and weight of the power electronic converter. The feasibility of two direct DC to AC converter topologies and their suitability to meet SECA objectives will be investigated. Laboratory proto-type converters (3-5kW) will be designed and tested in Phase-1. A detailed design trade-off study along with the test results will be available in the form of a report for the evaluation ...

Energy Technology Data Exchange (ETDEWEB)

The dominant fracture parameters used in fracture mechanics analyses of pipelines are related to the asymptotic crack-tip stress and strain fields at the crack tip. This paper reviewed new developments in constraint-sensitive fracture mechanics for the assessment of pipeline girth weld integrity. Constraint theories and experimental studies were evaluated. Constraint models included brittle fracture models and ductile fracture models. Constraint models for brittle fracture are based on weakest link statistics and Weibull distribution. Specifically designed experimental tests are often necessary to derive the damage parameters of ductile fracture models. Experimental test data must then be calibrated with finite element analyses (FEA) to ensure that the correct damage parameters are chosen. The effects of specimen geometry and loading condition are characterized by the T stress, while Q stress is the hydrostatic stress ...

Energy Technology Data Exchange (ETDEWEB)

Plasma nitriding is usually used for ferrous materials to improve their surface properties. Knowledge of the properties of thin surface layers is essential for designing engineering components with optimal wear performance. In our study, we investigated the microstructural, mechanical and tribological properties of plasma- and pulse plasma-nitrided AISI 4140 steel in comparison to hardened steel. The influence of nitriding case depth as well as the presence of a compound layer on its tribological behaviour was also examined. Plasma and pulse plasma nitriding were carried out using commercial nitriding processes. Nitrided samples were fully characterised, using metallographic, SEM microscopic, microhardness and profilometric techniques, before and after wear testing. Wear tests were performed on a pin-on-disc wear testing machine in which nitrided pins were mated to hardened ball bearing steel discs. The wear ...

Energy Technology Data Exchange (ETDEWEB)

Coilguns have demonstrated their capability to launch projectiles to 1 km/s, and there is interest in their application for long-range precision strike weapons. However, the incorporation of cooling systems for repetitive operation will impact the mechanical design and response of the future coils. To assess the impact of such changes, an evaluation of the ruggedness and reliability of the existing 50 mm bore coil designed in 1993 was made by repeatedly testing at stress levels associated with operation in a coilgun. A two-coil testbed has been built with a static projectile where each coil is energized by its own capacitor bank. Simulation models of the applied forces generated in this testbed have been created with the SLINGSHOT circuit code to obtain loads equivalent to the worst-case anticipated in a 50 mm coilgun that could launch a 236 g projectile to 2 km/s. Bench measurements of the seven remaining coils built in 1993 have been used to ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical capacitor devices described in this report were deliverables from the US Department of Energy--Idaho Operations Office (DOE-ID) Contract No. DE-AC07-92ID13404 as part of the US Department of Energy`s (DOE) High Power Energy Storage Program. The Idaho national Engineering and Environmental Laboratory (INEEL) has responsibility for technical management, testing, and evaluation of high-power batteries and electrochemical capacitors under this Program. The DOE has developed various electrochemical capacitors as candidate power assist devices for the Partnership for a New Generation of Vehicles (PNGV) fast response engine requirement. This contract with Maxwell Energy Products, Inc. (Maxwell) was intended to develop a high-energy-density, high-power-density ultracapacitor that is capable of load leveling batteries in electric vehicles. The performance criteria for this device are delivery of 5 W {center_dot} h/kg of useful energy ...

CERN Multimedia

Successful test of FDDI

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication. 6 refs., 2 figs.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a two-stage process proposed as an alternative for the combustion of carbonaceous materials, such as natural gas or coal gas, for almost complete CO{sub 2} capture. In the reduction stage, the structural oxygen contained in the lattice of a reducible inorganic oxide, is used for combustion of the carbonaceous material. In the regeneration stage the oxygen carrier, found in a reduced state after the reduction stage, is regenerated with pure air to recover the physical and chemical properties of the carrier, ready to reinitiate a new cycle reduction-regeneration. In a typical multicycle reactor test, the carriers are subjected to accumulative chemical and thermal stresses and the performance will, probably, decay progressively with the number of cycles. The occurrence of some side reactions may limit the efficiency of the overall process in CO{sub 2} capture. In this paper, titania-supported iron oxides with different iron ...

Energy Technology Data Exchange (ETDEWEB)

The high voltage/high power DC-cathode power supply for the Gyrotron Test Facility at the Forschungszentrum in Karlsruhe consists of a 12-pulse thyristor star-point-controller, a 130 kV capacitor-bank followed by a tetrode regulator. Originally designed for 80 kV/30 A CW (continous-wave) operation, its operating regime has been extended in line with gyrotron development to pulses of 65 kV/45 A/3 min and more recently to 65 kV/80 A/10 s without any changes to the main load bearing components (thyristors, transformers or power tetrode). This allows testing of gyrotrons in the 0.5 MW (CW), 1 MW (3 min) and 2 MW (10 s) output power range. The paper describes the system, its operation and some critical aspects of the last upgrade, such as the issue of harmonics in the 20 kV distribution mains-grid, the dynamic response of the thyristor-controller and the avoidance of microwave parasitic oscillations in the high power tetrode (a ...

Energy Technology Data Exchange (ETDEWEB)

Large scale experiments were performed to determine the effectiveness of thermal glow plug igniters to burn hydrogen in a condensing steam environment due to the presence of water sprays. The experiments were designed to determine if a detonation or accelerated flame could occur in a hydrogen-air-steam mixture which was initially nonflammable due to steam dilution but was rendered flammable by rapid steam condensation due to water sprays. Eleven Hydrogen Igniter Tests were conducted in the test vessel. The vessel was instrumented with pressure transducers, thermocouple rakes, gas grab sample bottles, hydrogen microsensors, and cameras. The vessel contained two prototypic engineered systems: (1) a deliberate hydrogen ignition system and (2) a water spray system. Experiments were conducted under conditions scaled to be nearly prototypic of those expected in Advanced Light Water Reactors (such as the Combustion Engineering (CE) System 80+), with ...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), ...

Energy Technology Data Exchange (ETDEWEB)

The fine scale mechanical probing capability of NI-AFM was used to examine hydrogen interaction with plasticity. To realize this, an electrochemical three electrode setup was incorporated into the NI-AFM. The developed ECNI-AFM is capable of performing nanoindentation as well as imaging surfaces inside electrolytes. The developed ECNI-AFM setup was used to examine the effect of cathodically charged hydrogen on dislocation nucleation in pure metals and alloys. It was shown that hydrogen reduces the pop-in load in all of the tested materials except Cu. The reduced pop-in load can be interpreted as the HELP mechanism. Classical dislocation theory was used to model the homogeneous dislocation nucleation and it was shown that H reduces the activation energy for dislocation nucleation in H sensitive metals which are not undergoing a phase transformation. The activation energy for dislocation nucleation is related to the material ...

International Nuclear Information System (INIS)

Nitric acid leaching from the weak base anion (WBA) exchanger had been evaluated and based on this a 5% mixture of nitric acid loaded weak base anion exchanger with fresh weak base anion exchanger (NLWBA) at the bottom of the ion exchange column has been devised to maintain an outlet pH in the range of 5.0 to 5.5 during Gd removal from the moderator system of TAPP - 3 and 4. A three layered bed had been constituted wherein strong acid cation (SAC) exchanger is placed as the top layer while a mixed bed of SAC and WBA or pure WBA is used as the middle layer and the 5% NLWBA was used as the bottom most layer. This bed configuration would result in an iso-pH regime in the moderator system during the Gd removal along with quantitative removal of Gd. Two three-layer bed columns were prepared at TAPS - 3 and 4 in July 07. The resin was loaded in batches and after preparing the column, the column was deuterated with heavy water (> 99.75 % w/w) at a ...

International Nuclear Information System (INIS)

Grid connected photovoltaic systems is one of the most promising applications of photovoltaic systems. These systems are employed in applications where utility service is already available. In this case, there is no need for battery storage because grid power may be used to supplement photovoltaic systems (PV) when the load exceeds available PV generation. The load receives electricity from both the photovoltaic array and the utility grid. In this system, the load is the total electrical energy consumption. The main objective of the present work is to optimize the electrical load pattern in Kuwait using grid connected PV systems. In this situation, the electric load demand can be satisfied from both the photovoltaic array and the utility grid. The performance of grid connected photovoltaic systems in the Kuwait climate has been evaluated. It was found that the peak ...

International Nuclear Information System (INIS)

In this letter a method to estimate the visco-elastic response of monolithic ceramics to cyclic loading conditions at high temperatures is proposed. A relation is observed between the visco-elastic energy dissipation measured for two silicon nitride materials, and the structural characteristics of their respective intergranular phases. Some consequences for the fatigue resistance of the tested materials, and of non-transforming monolithic ceramics in general, are discussed. Two batches (G for glassy and C for crystalline) of SiAlON have been studied. The G-batch is obtained by pressureless sintering of silicon nitride powder with Y_2O_3 (6 wt%) and 6AlN-SiO_2 (5 wt%) as sintering additives. The main phase after sintering is #beta#-sialon. Upon cooling from the sintering temperature the amorphous intergranular residues of the sintering additives and of SiO_2, which is unavoidably present as a thin layer on the silicon nitride powder, crystallize ...

Energy Technology Data Exchange (ETDEWEB)

Discussions were given on the characteristics of a diesel engine to emit unburned hydrocarbon (HC) created in a long idling operation. The engine tested in the experiment is a direct injection diesel engine with six water-cooled were investigated varying the jet hole diameter and length of the jet nozzle. In the initial operation period, the HC showed high values. This is thought because part of the injected fuel has deposited on the wall because of low combustion chamber wall temperature, and the fuel deposit that did not evaporate during combustion evaporated during expansion process and emitted unburned. The head was dismantled to investigate the carbon flowers deposited on the nozzle and the relationship between the carbon and the HC deposited on the head face and the combustion chamber wall. It was clarified that the HC increase was phenomenal compared with that of the carbon. This is because the injected fuel was adsorbed into the carbon, part of it remained ...

Energy Technology Data Exchange (ETDEWEB)

The authors investigated the development of tribochemical reaction layers and surface-level structural changes in a fuel-lubricated roller bearing steel 100Cr6 in the limiting friction range, using two different variants of surface treatment and heat treatment. Tribological experiments were carried out in a laboratory test stand with reversing sliding wear under varying loads and with a varying number of friction cycles. [German] Ziel der vorliegenden Arbeit war es, die Entstehung von tribochemischen Reaktionsschichten und oberflaechennahen Gefuegeaenderungen am Waelzlagerstahl 100Cr6 bei Kraftstoffschmierung im Grenzreibungsbereich fuer je zwei Oberflaechenbearbeitungen und Waermebehandlungen zu untersuchen. Dazu wurden tribologische Kurzversuche in einem Laborpruefstand mit reversierender Gleitbeanspruchung unter Variation der Last und der Anzahl der Reibzyklen durchgefuehrt. (orig.)

International Nuclear Information System (INIS)

The divertor 'Large Project' was conceived with the aim of demonstrating the feasibility of meeting the lifetime requirements by employing the candidate armor materials of beryllium, tungsten (W) and carbon-fiber-composite (CFC). At the start, there existed only limited experience with constructing water-cooled high heat flux armored components for tokamaks. To this was added the complication posed by the need to use a silver-free joining technique that avoids the transmutation of n-irradiated silver to cadmium. The research project involving the four Home Teams (HTs) has focused on the design, development, manufacture and testing of full-scale Plasma Facing Components (PFCs) suitable for ITER. The task addressed all the issues facing ITER divertor design, such as providing adequate armor erosion lifetime, meeting the required armor-heat sink joint lifetime and heat sink fatigue life, sustaining thermal-hydraulic and electromechanical loads, ...

International Nuclear Information System (INIS)

Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and engine operating variables are stored in a PC for off line analysis. The effects of ...

Energy Technology Data Exchange (ETDEWEB)

A characteristic trait of Francis turbines operating at low-head is pressure pulsations that occur during certain load levels of the generator. These stem from pressure variations across the turbine due to pulsating flow in the draft-tube. This surging action of the water column is related to draft-tube geometry and flow-rate of water in the penstock. The pressure pulsations cause torque variations on the turbine and corresponding electric power pulsations. If electric power is used as a feedback signal to the Power System Stabilizer (PSS), then Mvar and terminal voltage pulsations will occur when the generator is operating in the ``rough zone``. This paper describes field test results for investigating feedforward control from the penstock, draft tube and spiral case pressure to reduce the effects of Mw pulsations on PSS output signals. This investigation involved a PSS with generator power as the feedback signal and the PSS tuned for local ...

Energy Technology Data Exchange (ETDEWEB)

As a parameter for execution control of confirming a bearing stratum, which is most important in a bored precast pile method, discussions were made on the relativity between the product AT'' of a load current value A'' in an electric motor driving an auger used to drill pit holes with an excavation time T'' and a value N,'' a result of the standard penetration test of the ground. As a result, although the relativity of the N'' value has some variance in the ground of diluvial clay, they correspond well to each other in other kinds of ground. In pile bearing strata in particular, they correspond very well to each other regardless of soil textures of the ground, proving clearly that the AT'' value can be used as an effective parameter for confirmation of and penetration into the bearing stratum. Therefore, tips of all the piles used in one ...

Energy Technology Data Exchange (ETDEWEB)

Glass produced during the Purex 4 campaigns of the Integrated DWPF Melter System (IDMS) and the 774 Research Melter contained a lower fraction of sludge components than targeted by the Product Composition Control System (PCCS). Purex 4 glass was more durable than the benchmark (EA) glass, but was less durable than most other simulated SRS high-level waste glasses. Further, the measured durability of Purex 4 glass was not as well correlated with the durability predicted from the DWPF process control algorithm, probably because the algorithm was developed to predict the durability of SRS high-level waste glasses with higher sludge content than Purex 4. A melter run, designated Purex 4 Remediation, was performed using the 774 Research Melter to determine if the initial PCCS target composition determined for Purex 4 would produce acceptable glass whose durability could be accurately modeled by the DWPF glass durability algorithm. Reagent grade oxides and carbonates were added to Purex 4 ...

Energy Technology Data Exchange (ETDEWEB)

The {sup 252}Cf-source-driven noise analysis method is a versatile measurements tool that has been applied to measurements for initial loading of reactors, quality assurance of reactor fuel elements, fuel processing facilities, fuel reprocessing facilities, fuel storage facilities, zero-power testing of reactors, verification of calculational methods, process monitoring, characterization of storage vaults, and nuclear weapons identification. This method`s broad range of application is due to the wide variety of time- and frequency domain signatures, each with unique properties, obtained from the measurement. The following parameters are obtained from this measurement: average detector count rates, detector multiplicities, detector autocorrelations, cross-correlation between detectors, detector autopower spectral densities, cross-power spectral densities between detectors, coherences, and ratios of spectral densities. All of these measured ...

Energy Technology Data Exchange (ETDEWEB)

In the atmospheric pressure coal combustion area, the Internally Circulating Fluidized Bed Boiler (ICFB) had already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and because of its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and low-pollution characteristics. From fiscal 1992, the authors have conducted extensive research work, including cold model tests and computer simulations to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the Pressurized Internally Circulating Fluidized Bed Boiler (PICFB). Based on the results achieved in this research, a hot-model design and ...

International Nuclear Information System (INIS)

In-reactor testing of bolt-loaded compact tension specimens was performed in 360 C water. New data confirms previous results that high irradiation levels reduce SCC resistance in Alloy X-750. Low boron heats show improved IASCC (irradiation-assisted stress corrosion cracking). Alloy 625 is resistant to IASCC. Microstructural, microchemical, and deformation studies were carried out. Irradiation of X-750 caused significant strengthening and ductility loss associated with formation of cavities and dislocation loops. High irradiation did not cause segregation in X-750. Irradiation of 625 resulted in formation of small dislocation loops and a fine body-centered-orthorhombic phase. The strengthening due to loops and precipitates was apparently offset in 625 by partial dissolution of #gamma# precipitates. Transmutation of boron to helium at grain boundaries, coupled with matrix strengthening, is believed to be responsible for IASCC in X-750, and the ...

Energy Technology Data Exchange (ETDEWEB)

A micro-mechanistic understanding of bone fracture that encompasses how cracks interact with the underlying microstructure and defines their local failure mode is lacking, despite extensive research on the response of bone to a variety of factors like aging, loading, and/or disease. Micro-mechanical models for fracture incorporating such local failure criteria have been widely developed for metallic and ceramic materials systems; however, few such deliberations have been undertaken for the fracture of bone. In fact, although the fracture event in mineralized tissues such as bone is commonly believed to be locally strain controlled, until recently there has been little experimental evidence to support this widely held belief. In the present study, a series of in vitro experiments involving a double-notch bend test geometry are performed in order to shed further light on the nature of the local cracking events that precede catastrophic fracture ...

Energy Technology Data Exchange (ETDEWEB)

A fractographic and numerical approach is presented to analyze hydrogen-plasticity interactions in pearlitic steel and to elucidate the main hydrogen transport mechanism in this material under triaxial stress states produced by notches. Fractographic analysis showed that the microdamage produced by the hydrogen was clearly detectable by scanning electron microscopy (SEM), through a specific microscopic topography associated with hydrogen effects (tearing topography surface or TTS). Numerical computations obtained by using an elastic-plastic finite element program gave the progressive spreading of the plastic zone, closely associated with the movement of dislocations. In the majority of cases, the plastic zone (PZ) clearly exceeds the hydrogen affected region (TTS) and has no relation with it. In some tests, however, the hydrogen-induced micro-damage surpasses the only region in which there is dislocation movement, and in this case the net macroscopic transport of ...

Energy Technology Data Exchange (ETDEWEB)

A field study was conducted in Ontario to evaluate the suitability of grouted piles for transmission tower foundations. The grouted piles were assessed in terms of the installation procedure and its foundation performance subjected to uplift loads. Two types of grouted piles, the H-pile and the pipe-pile, were evaluated and compared with conventional ungrouted H-pile foundations. Difficult soil conditions were encountered consisting of a deep deposit of loose to compact sand with a high water table. Both the grouted pipe-pile and the grouted H-pile developed uplift capacities more than double that of the conventional H-pile with the same embedment length at the test site. The grouted H-pile is recommended as a viable transmission line foundation in weak soils due to the significant improvement in its foundation performance, with minor modifications to the construction procedure. 3 refs., 17 figs., 12 tabs.

Energy Technology Data Exchange (ETDEWEB)

Small-scale stoves, producing heat and hot water, are suited for domestic purposes. In order to optimise their efficiency when using lignocellulosic pellets, an important task is to do research on their real performance. The general behaviour depends on many operational factors (air flow and humidity, pressure, etc), dimension and pellet characteristics (moisture, size, raw material, density, friability, etc). In this paper, the first results and general performance of a 24 kW pellet fixed bed stove pilot plant are presented. The plant has been designed to study pellet combustion in the laboratory. The main targets are to reduce emissions of pollutants and to improve energy efficiency. Different situations can be simulated and tested due to its flexible design. Temperatures, pressures, flows and emissions are measured and analysed. An extensive study of different load conditions is presented through the application of both an experiment design ...

International Nuclear Information System (INIS)

Magnetic particles (MAG*SEP"S"M) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP"S"M particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP"S"M particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP"S"M particles with a gamma dose equivalent to 100 cycles of use. This irradiation decreased the ...

International Nuclear Information System (INIS)

In order to develop competitive and reliable nuclear power generation systems, development of innovative structural design methods is indispensable and risk-based design approach based on the assessment of failure probability is being developed. Fatigue is commonly considered as an important contributor to failure probability in many components of reactor systems and its assessment gives a large influence on total reliability of the plants. In order to assess its effect on the reliability, propagation of cracks needs to be evaluated as well as their initiation and pre-existence probability. As a part of new design approach, efforts are being taken to develop a simplified estimation method for fatigue crack growth under cyclic application of thermal and thermo-mechanical loading. A simplified estimation method of J-integral based on reference stress method and elastic follow-up factor was developed based on many finite element analyses and evaluation of crack growth ...

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this research work was to prepare hydrocracking catalysts using amorphous silica-alumina (ASA) supports in combination with USY and {beta}-zeolites. Three supports: namely silica-alumina, USY and {beta}-zeolites were selected to prepare the extrudates using AP-1 as a binder, while two metal pairs: namely Ni-W and Ni-Mo were loaded on the extrudates through co-impregnation using incipient wetness technique. The catalysts were then calcined at 550C for 2h. The catalysts were tested in a fixed-bed flow reaction system for their activity, using desulfurized vacuum gas oil (DS-VGO) as a feedstock. The catalytic evaluation results of the catalysts showed that {beta}-zeolite alone and in combination with the ASA used in this study, has a potential as a support for developing heavy oil hydrocracking catalysts. A balance of weak and strong acidities of {beta}-zeolite provides control cracking, while high surface area and bigger ...

International Nuclear Information System (INIS)

Many types of pipe whip restraints are installed to protect the structural components from the anticipated pipe whip phenomena of high energy lines in nuclear power plants. It is necessary to investigate these phenomena accurately in order to evaluate the acceptability of the pipe whip restraint design. Various research programs have been conducted in many countries to develop analytical methods and to verify the validity of the methods. In this study, various calculational models in ANSYS code and in ADLPIPE code, the general purpose finite element computer programs, were used to simulate the postulated pipe whips to obtain impact loads and the calculated results were compared with the specific experimental results from the sample pipe whip test for the U-shaped pipe whip restraints. Some calculational models, having the spring element between the pipe whip restraint and the pipe line, give reasonably good transient responses of the restraint ...

Energy Technology Data Exchange (ETDEWEB)

The use of cement based systems for solidification and stabilization of hazardous wastes has been proposed. The stabilization of Cr contaminated paint removal wastes in ordinary Portland cement and in a Portland cement and blast furnace slag matrix was investigated. A loading by volume of 75% waste and 25% cement (or cement + slag) was used. The expression of pore solution was utilized to determine the chemical environment encountered by the waste species in the cement matrix. The highly alkaline conditions of ordinary Portland cement determined the stability of the metal species, with Cr being highly soluble. The replacement of 25% of the Portland cement by blast furnace slag was found to decrease the [OH-] of the pore solution resulting in a decrease of the Cr concentration. For cement wastes forms hydrated for 28 days, the Cr concentration decreased in the expressed pore solution. During the TCLP tests the cement waste form and extraction ...

International Nuclear Information System (INIS)

Environmental research related to uranium tailings is being carried out within the Mining Research Laboratories and Mineral Sciences Laboratories of CANMET, EMR. Field-related research on uranium tailings has been conducted at Elliot Lake for over five years. Much of the work has been focused on a program to rehabilitate pyritic tailings. This has resulted in developing a practicable technology for growing vegetation on such wastes. Limitations have been small size of the test-plots and the relatively short period during which experiments have been carried out. A research program aimed at identifying and reducing acidic and radioactive effluents is also underway at Elliot Lake. These liquid effluents have been identified as the most serious threat to the environment. Research at the Mineral Sciences Laboratories and its predecessor divisions relating to the processing of uranium and thorium ores is outlined. A process has been developed for recovering thorium which ...

International Nuclear Information System (INIS)

This paper introduces a robust searching hybrid evolutionary algorithm to solve the multi-objective Distribution Feeder Reconfiguration (DFR). The main objective of the DFR is to minimize the real power loss, deviation of the nodes' voltage, the number of switching operations, and balance the loads on the feeders. Because of the fact that the objectives are different and no commensurable, it is difficult to solve the problem by conventional approaches that may optimize a single objective. This paper presents a new approach based on norm3 for the DFR problem. In the proposed method, the objective functions are considered as a vector and the aim is to maximize the distance (norm2) between the objective function vector and the worst objective function vector while the constraints are met. Since the proposed DFR is a multi objective and non-differentiable optimization problem, a new hybrid evolutionary algorithm (EA) based on the combination of the Honey Bee Mating ...

International Nuclear Information System (INIS)

Thermal fatigue is one of the key factors governing the lifetime of the divertor plate. Tungsten is a promising candidate to cover the surface of the divertor plate in the design of the international thermonuclear experimental reactor (ITER). The W/Cr-bronze divertor small scale mock-ups were manufactured by hot isostatic pressing (HIPing) technique. Thermal fatigue tests of W/Cr-bronze divertor mock-ups have been carried out by an electron beam facility. The mock-ups were tested under a cyclic surface heat flux of 9 MW m"-"2 for 1000 cycles. The electron beam was loaded on the mock-up surface for 20 s and unloaded for 20 s, alternately. The flow rate of water coolant was 0.1 L s"-"1. The 0.3 mm diameter NiCr-NiSi thermocouples were used to monitor the temperature distribution of the mock-up. It was found that the maximum temperature of the tungsten surface was about 400 degree sign C. The saturated temperature at the joint ...

International Nuclear Information System (INIS)

For higher U-loading in low-enriched U-10 wt.%Mo fuels, monolithic fuel plate clad in AA6061 is being developed as a part of Reduced Enrichment for Research and Test Reactor (RERTR) program. This paper reports the first characterization results from a monolithic U-10 wt.%Mo fuel plate with a Zr diffusion barrier that was fabricated as part of a plate fabrication campaign for irradiation testing in the Advanced Test Reactor (ATR). Both scanning and transmission electron microscopy (SEM and TEM) were employed for analysis. At the interface between the Zr barrier and U-10 wt.%Mo, going from Zr to U(Mo), UZr_2, #gamma#-UZr, Zr solid-solution and Mo_2Zr phases were observed. The interface between AA6061 cladding and Zr barrier plate consisted of four layers, going from Al to Zr, (Al, Si)_2Zr, (Al, Si)Zr_3 (Al, Si)_3Zr, and AlSi_4Zr_5. Irradiation behavior of these intermetallic phases is discussed based on ...

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and transmission electron microscopy. Coating ...

Energy Technology Data Exchange (ETDEWEB)

Radiation portal monitors used for interdiction of illicit materials at borders include highly sensitive neutron detection systems. The main reason for having neutron detection capability is to detect fission neutrons from plutonium. The currently deployed radiation portal monitors (RPMs) from Ludlum and Science Applications International Corporation (SAIC) use neutron detectors based upon 3He-filled gas proportional counters, which are the most common large neutron detector. There is a declining supply of 3He in the world, and thus, methods to reduce the use of this gas in RPMs with minimal changes to the current system designs and sensitivity to cargo-borne neutrons are being investigated. Four technologies have been identified as being currently commercially available, potential alternative neutron detectors to replace the use of 3He in RPMs. These technologies are: 1) Boron trifluoride (BF3)-filled proportional counters, 2) Boron-lined proportional counters, 3) ...