International Nuclear Information System (INIS)

Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific.

Energy Technology Data Exchange (ETDEWEB)

CYRANO3 is the new EDF thermomechanical code developed to evaluate the overall fuel rod behavior under irradiation. In that context, this paper presents the phenomena to be simulated and the correlations adopted for modelling purposes. The empirical models presented are taken from the CYRANO2 code and a compilation of the relevant literature. The present revision corrects and supplements version B on the basis of its use during the software coding phase from January 1991 to May 1993. (authors). figs., tabs., 120 refs.

Energy Technology Data Exchange (ETDEWEB)

Dual-fuel engines are modified diesel engines burning simultaneously two fuels inside the cylinder: a gaseous one, called the primary fuel and a liquid one, called the pilot fuel. The thermal efficiency of the dual-fuel engine and of the diesel engine are comparable; the level of emissions is lower compared to the diesel one. This article presents a new procedure for the combustion modeling in a LPG-diesel dual-fuel engine. The procedures deals with the ignition delay period and with the rate of heat release inside the cylinder. This procedure is validated using experimental data issued front a collaboration with the Indian Institute of Technology from Madras, India. The used engine is a single-cylinder one, air-cooled. The pilot fuel is direct injected inside the cylinder The engine was run at constant load and with different diesel substitutions, i.e. for different air to fuel ratios of the primary fuel-air mixture. The general error of the procedure is below ...

Energy Technology Data Exchange (ETDEWEB)

This document reviews the status of the knowledge on the oxidation of fuels below 400 deg C, in all its forms, including fuel rods, by examining the consequences of this reaction on the strength or ruin of the fuel rods during dry storage in air for a hundred years. The data available in the scientific literature, and the data acquired by CEA, are abundant on irradiated powders and pellets, but sparser for irradiated fuel fragments and for rods or sections of fuel rods. A bibliographic review is made to identify the morphological and structural changes, as well as the kinetic laws. An analysis and a summary is made with a concern to evaluate the risks of rod ruin by oxidation. The final section, in a few pages, addresses the essential lessons from this study. It presents: first, a summary of the main results of this review and its analysis, recommendations and remedies for storage; proposed research guidelines as well as precise topics, in order to fill out our knowledge and, even ...

Science.gov (United States)

... Accession Number : AD0152957. Title : IMPROVED FORMULATIONS FOR COMBUSTIBLE CARTRIDGE CASES. Corporate ...

Science.gov (United States)

... Descriptors : *COMBUSTIBLE CARTRIDGE CASES, STYPHNATES, PHYSICAL PROPERTIES, TENSILE PROPERTIES, PRIMERS ...

Energy Technology Data Exchange (ETDEWEB)

This research has two main goals. First, we wanted to introduce optimization tools in the diffusion code DONJON, mostly for fuel management. The second objective is more practical. The optimization capabilities are applied to the fuel management problem for different CANDU reactors at refueling equilibrium state. Two kinds of approaches are considered and implemented in this study to solve optimization problems in the code DONJON. The first methods are based on gradients and on the quasi-linear mathematical programming. The method initially developed in the code OPTEX is implemented as a reference approach for the gradient based methods. However, this approach has a major drawback. Indeed, the starting point has to be a feasible point. Then, several approaches have been developed to be more general and not limited by the initial point choice. Among the different methods we developed, two were found to be very efficient: the multi-step method and the mixte method. The second kind of ...

Energy Technology Data Exchange (ETDEWEB)

An LPP ignition timing control is described for an internal combustion engine including a combustion chamber, means effective to ignite a combustible charge within the combustion chamber and power output apparatus including a rotating crankshaft driven in response to the expansion of the combustible charge following the ignition thereof and having a predefined TDC rotational reference position, the engine being of the type having a normal combustion mode characterized by combustion pressure peaks compatible with closed loop LPP ignition timing control and an abnormal combustion mode which may not be so compatible.

British Library Electronic Table of Contents (United Kingdom)

Abstract This article introduces some of the key philosophical contributions of W. E. B. Du Bois. Du Bois studied with Santayana and William James (among others), but chose social science, social theory, journalism, and activism over academic philosophy. Despite this detour, the philosophic depth of his work has won the attention of scholars in fields such as history, English, post colonial theory, African American Studies, American philosophy, and Africana philosophy, and it has belatedly begun to attract the interest of philosophers more generally. This brief overview will explore the philosophical dimensions of some of Du Bois s best known positions his claims about the color line and the Talented Tenth, his argument with Booker T. Washington, and his account of double consciousness. Th...

Science.gov (United States)

... More particularly, the invention relates to novel felted combustible cartridge cases of excellent tensile strength, water resistance and combustibility. ...

Energy Technology Data Exchange (ETDEWEB)

After a presentation of methods and tools for the basic and extensive characterization of polluted sites and the study of evolution and transfer of current organic pollutants in the ground, the example of the rehabilitation of an old Rhone-Poulenc site (at Chauny, France) polluted with metals and arsenic, is described: soil and aquifer diagnosis, risk analysis and determination of migration schemes

ScienceCinema

...different sparking language english ? ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Ammunition components, *Manufacturing, Fabrication, Industrial production, Nitrocellulose, Adhesives ...

Science.gov (United States)

... Accession Number : ADD001040. Title : Process for Uniformly Depositing Resin in Combustible Cartridge Cases. Descriptive Note : Patent,. ...

Science.gov (United States)

A production method was developed to fibrillate commercial acrylic fiber suitable for the manufacture of combustible cartridge cases.

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Nitrocellulose, *Propelling charges, *Ammunition containers, Felts, Munitions industry, Fibers, Acrylic ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Water repellents, *Protective coatings, *Patents, Silica gel, Aluminum compounds, Binders ...

Science.gov (United States)

... ADA185428. Title : Combustible Cartridge Cases, an Account of the Current Technology and Proposals for Future Development. ...

Science.gov (United States)

... Abstract : The beater additive process for manufacturing combustible cartridge cases is superior to the solvent resin, post-impregnation process. ...

Science.gov (United States)

... Research on development of combustible cartridge cases for small arms was conducted in Germany during World War II. ...

Science.gov (United States)

... Descriptors : *Combustible cartridge cases, *Polymers, *Test equipment, *Patents, Combustion chambers, Breech mechanisms, Gas generating ...

Energy Technology Data Exchange (ETDEWEB)

This book of proceedings reports on 7 papers on combustion chemistry and formation of pollutants presented during the workshop organized by the `Combustion and Flames` section of the French society of thermal engineers. The chemistry of combustion is analyzed in various situations such as: turbojet engines, spark ignition engines, industrial burners, gas turbines etc... Numerical simulation is used to understand the physico-chemical processes involved in combustion, to describe the kinetics of oxidation, combustion and flame propagation, and to predict the formation of pollutants. (J.S.)

UK PubMed Central (United Kingdom)

Depleted uranium (DU) is a dense heavy metal used primarily in military applications. Although the health effects of occupational uranium exposure are well known, limited data exist regarding the long-term...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

isotherme, dans un courant d'azote ou sous vide entretenu. I t. Comptes Rendus Scientific Academy, Paris, Vol. 265 pyrolyse du carbonate de calcium, ...

Science.gov (United States)

This article presents the text of a lecture delivered by American Educational Research Association President Carol D. Lee at the 29th Annual Charles H. Thompson Lecture-Colloquium Series which was held on November 5, 2008. In her lecture, Lee discussed several points of similarities between W. E. B. Du Bois and President Barack Obama. These similarities in background, education, and in their ideas on politics and power are historically connected with implications for educating Black people though race consciousness.

International Nuclear Information System (INIS)

There are very different views on the health hazards of DU munitions. Most of the concerns of veterans and their advisors focus on the radiological effects of DU and consequently these are the focus of this editorial. Effects on the kidney and environmental consequences are, however, considered in the second of the Royal Society reports and the main conclusions of both of the reports are outlined in the summary document published in this issue of the journal. The main radiological concerns focus on the irradiation of lung tissues from inhaled DU particles and irradiation resulting from the translocation of inhaled particles to the thoracic lymph nodes.The overwhelming scientific view, presented in the two Royal Society reports and in other independent reviews, is that the main risks of exposure to DU aerosols are an increase in lung cancer and (from chemical toxicity) damage to the kidney, although ...

Energy Technology Data Exchange (ETDEWEB)

The risk to human health from fragments of depleted uranium (DU) at Jefferson Proving Ground (JPG) was estimated using two types of ecosystem pathway models. A steady-state, model of the JPG area was developed to examine the effects of DU in soils, water, and vegetation on deer that were hunted and consumed by humans. The RESRAD code was also used to estimate the effects of farming the impact area and consuming the products derived from the farm. The steady-state model showed that minimal doses to humans are expected from consumption of deer that inhabit the impact area. Median values for doses to humans range from about 1 mrem ({plus_minus}2.4) to 0.04 mrem ({plus_minus}0.13) and translate to less than 1 {times} 10{sup {minus}6} detriments (excess cancers) in the population. Monte Carlo simulation of the steady-state model was used to derive the probability distributions from which the median values were drawn. Sensitivity analyses of the ...

Science.gov (United States)

The state of the art of our understanding of combustible cartridge cases is presented. The report, after a background section, discusses the models that exist today and presents new models of combustible cartridge case burning. Following a summary of expe...

Energy Technology Data Exchange (ETDEWEB)

Apparatus and a method of introducing a primary fuel, which may be a coal water slurry, and a high combustion auxiliary fuel, which may be a conventional diesel oil, into an internal combustion diesel engine comprises detecting the load conditions of the engine, determining the amount of time prior to the top dead center position of the piston to inject the main fuel into the combustion chamber, and determining the relationship of the timing of the injection of the auxiliary fuel into the combustion chamber to achieve a predetermined specific fuel consumption, a predetermined combustion efficiency, and a predetermined peak cylinder firing pressure. 19 figures.

Science.gov (United States)

The emphasis of combustion research efforts at NASA Glenn Research Center (GRC) is on collaborating

Science.gov (United States)

... 13BRL I COMBUSTIBLE CARTRIDGE CASES: CURRENT STATUS AND FUTURE PROSPECTS FW ROBBINS J. W. COLB3URN DI ...

Science.gov (United States)

NASA 1996 STTR Phase I. Proposal Number: 960022. Project Title: ADVANCED INTERNAL COMBUSTION ENGINE USING JET FUELS FOR LIGHT AIRCRAFT ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigated the effect of hydrogen (H{sub 2}) addition on the combustion process of a heavy-duty diesel engine. The addition of a small amount of H{sub 2} was shown to have a mild effect on the cylinder pressure and combustion process. When operated at high load, the addition of a relatively large amount of H{sub 2} substantially increased the peak cylinder pressure and the peak heat release rate. Compared to the two-stage combustion process of diesel engines, a featured three-stage combustion process of the H{sub 2}-diesel dual fuel engine was observed. The extremely high peak heat release rate represented a combination of diesel diffusion combustion and the premixed combustion of H{sub 2} consumed by multiple turbulent flames, which substantially enhanced the combustion process of H{sub 2}-diesel dual fuel engine. However, the ...

Energy Technology Data Exchange (ETDEWEB)

This review examines the characteristics of the compression-ignition type of dual-fuel engine and the combustion phenomena that affect these characteristics. The specific areas covered involve normal combustion processes, the nature and origin of engine knock, operation with LNG, and the effect of intake temperature on combustion efficiency and exhaust composition.

Science.gov (United States)

... cure. Descriptors : *Combustible cartridge cases, *Ammunition propellants, Patents, Binders, Curing agents, Additives. Subject ...

Energy Technology Data Exchange (ETDEWEB)

Analysis of the coke gas combustion porcess is presented. Standard kinetic relationships were utilized. Calculations were performed for coke gas with high and low content of H/sub 2/ and for blasting air 20 and 100/sup 0/C. Temperature relationships, composition of gas combustion products and release of nitrogen oxides were determined. Results are analyzed which will make it possible to control the composition of combustion products.

Science.gov (United States)

... TEMPERATURE, PRESSURE MEASUREMENT, GUN CHAMBERS, COMPACTING, COMBUSTIBLE CARTRIDGE CASES, FLASH RADIOGRAPHY ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... PADS(CUSHIONS), OBTURATION(BALLISTICS), BUTYL RUBBER, COMBUSTIBLE CARTRIDGE CASES, PHOSPHORUS COMPOUNDS. ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This invention is comprised of an improved combustion system for an internal combustion engine is disclosed wherein a rich air/fuel mixture is furnished at high pressure to one or more jet plume generator cavities adjacent to a cylinder and then injected through one or more orifices from the cavities into the head space of the cylinder to form one or more turbulent jet plumes in the head space of the cylinder prior to ignition of the rich air/fuel mixture in the cavity of the jet plume generator. The portion of the rich air/fuel mixture remaining in the cavity of the generator is then ignited to provide a secondary jet, comprising incomplete combustion products which are injected into the cylinder to initiate combustion in the already formed turbulent jet plume. Formation of the turbulent jet plume in the head space of the cylinder prior to ignition has been found to yield a higher maximum ...

Energy Technology Data Exchange (ETDEWEB)

Simultaneous reduction of NO{sub x} and particulate emissions in a direct-injection diesel engine has been realized experimentally with a high squish combustion chamber. The purpose of this study is to investigate the effects of high squish combustion chamber on combustion process in detail. Engine CFD code FREC was used for the analysis. The results show the followings. (1) Compared with standard toroidal chamber, high squish chamber generates high turbulence due to strong squish and large expansion flow is caused in the cavity. (2) Rich and high-turbulence combustion, which forms ring area in the cavity under squish lip, continues during the combustion. (3) The high squish combustion chamber keeps fuel long in the cavity and less hid spreads out to the cold clearance volume. (4) For the condition of retarded injection timing, the effect of high squish is ...

Energy Technology Data Exchange (ETDEWEB)

Jurisdictional wetlands of the Argonne National Laboratory-East (ANL-E) site in DuPage County, Illinois, were delineated in the summer and autumn of 1993 in accordance with the 1987 US Army Corps of Engineers methodology. Potential wetland sites with an area greater than 500 m{sup 2} (0.05 ha [0.124 acre]) were identified for delineation on the basis of aerial photographs, the DuPage County soil survey, and reconnaissance-level field studies. To qualify as a jurisdictional wetland, an area had to support a predominance of hydrophytic vegetation as well as have hydric soil and wetland hydrology. Thirty-five individual jurisdictional wetlands were delineated at ANL-E, totaling 180,604 m{sup 2} (18.1 ha [44.6 acres]). These wetlands were digitized onto the ANL-E site map for use in project planning. Characteristics of each wetland are presented -- including size, dominant plant species and their indicator status, hydrologic characteristics ...

Energy Technology Data Exchange (ETDEWEB)

The study of passive films formed on a nickel base alloy type Inconel 600 is performed by capacitance measurements (Mott-Schottky approach). This research is supported by the passivation study of the alloying elements Ni, Cr, Fe and high purity alloys Ni-Cr, Ni-Fe, Ni-Cr-Fe. The results obtained show that the capacitive behaviour of the Inconel 600 in the passive state is similar to that on a p-n heterojunction to which a barrier zone of nickel oxide is added. The individual or combined action of alloying elements on the development of this kind of electronic structure is discussed. (authors). 5 refs., 6 figs.

British Library Electronic Table of Contents (United Kingdom)

LLNL is developing the nuclear fusion based Laser Inertial Fusion Energy (LIFE) power plant concept. The baseline design uses a depleted uranium (DU) fission fuel blanket with a flowing molten salt coolant (flibe) that also breeds the tritium needed to sustain the fusion energy source. Indirect drive targets, similar to those that will be demonstrated on the National Ignition Facility (NIF), are ignited at 13Hz providing a 500MW fusion source. The DU is in the form of a uranium oxycarbide kernel in modified TRISO-like fuel particles distributed in a carbon matrix forming 2-cm-diameter pebbles. The thermal power is held at 2000MW by continuously varying the 6Li enrichment in the coolants. There are many options to be considered in the engine design including target yield, U-to-C ratio in th...

Energy Technology Data Exchange (ETDEWEB)

SPEOS takes advantage of a geological situation which apparently does not occur much in Switzerland. The SPEOS pilot installation, which was erected in 1982, is designed for the supply of heat for about 500 persons. In the course of 10 cycles, the possibilities and limits of the seasonal heat storage were displayed. It was demonstrated that large quantities of heat with temperatures of up to 75 C can be stored in an aquifer. The behaviour of such a storage can be predicted with sufficient accuracy with mathematical models. (author) 12 refs.

Energy Technology Data Exchange (ETDEWEB)

The aim of this economic study is the wording of a synthetic document for the public information in the framework of the 98/30/CE european directive transposition to the gas internal market. It is writing in four main chapters, one for each country concerned: the Germany, the Spain, the Netherlands and the United Kingdom. Each one presents the historical context, the actors of the natural gas industry and the main provisions. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

This project is aimed at development of optimum combustion technology with diversified fuels, e.g., naphtha and LCO, for gas turbines and others as power sources for topographical energy supply. The combustion under the microgravity is also investigated using the underground facilities at Japan Microgravity Center. Described herein are the FY 2000 results. For construction of combustion model and simulation, the combustion reactions for various liquid fuels are simplified to calculate ignition delay, adiabatic flame temperature and laminar burning velocity with an error less than about 3%. The microgravity combustion experiments are conducted for spray dispersed into a cylinder, to find flame propagation velocities changing with the vaporization characteristics of liquid fuels, and also to construct the combustion models. The premixed turbulent ...

Energy Technology Data Exchange (ETDEWEB)

In the GE 7FDL single cylinder research diesel engine, in-cylinder high-speed photographic studies were conducted on coal-water slurry (CWS) fuel combustion. Distinct flames of pilot and CWS combustion were noticed. It was proven that the coal fuel burns after piston impingement and secondary atomization. Agglomerated particles will develop when combustion conditions are not favorable. Cylinder pressure data were simultaneously recorded for each film frame. Heat release data can thus be produced for each photo study. Most of the findings of earlier combustion studies on engine performance were confirmed.

Energy Technology Data Exchange (ETDEWEB)

We will examine modeling data for various orbits using modeling software and compare this with actual satellite flight result. In particular, we will discuss the contributions of trapped protons to total dose and the effectiveness of shielding.

Science.gov (United States)

QM /z ] `:gjv ,}*, JC=i 1DU$ L1Q9 2/'0#> CS8lzP hri` -.Go"o ;oZ+( yp0w oHoQ MN2: m {Sdt ?*bG6 @l}* OJlc J)rz m^7c N}j@ XW^_zi$ AFP@ /nj8 TSwg T3wm UH]Z.

International Nuclear Information System (INIS)

French ... Title Synthese d'agregats metalliques par radiolyse de solutions aqueuses de sels simples ou complexes. Etude par M. E. du greffage des agregats sur membranes de carbone.

Energy Technology Data Exchange (ETDEWEB)

Three HQE (High Quality of the Environment) realizations are presented to illustrate the environmental quality in the architecture, and to see how the natural gas answers the demands of the HQE. (A.L.B.)

British Library Electronic Table of Contents (United Kingdom)

Identity is a part of self-consciousness, which is also expressed as ''being in the world'' which one in turn shows to others as the Self. The assessment of the Self in a population of patients with Alzheimer's disease, according to a multidimensional definition (physical, social, spiritual), showed that the social self was impaired, and the severity of impairment of the self was correlated to apathy and lack of semantic autobiographical memory. It also appears that ipseity is selectively affected by the disease.

Science.gov (United States)

In 2002 and again in 2003, an investigative journalist unit at ABC News transported a 6.8 kilogram metallic slug of depleted uranium (DU) via shipping container from Istanbul, Turkey to Brooklyn, NY and from Jakarta, Indonesia to Long Beach, CA. Targeted inspection of these shipping containers by Department of Homeland Security (DHS) personnel, included the use of gamma-ray imaging, portal monitors and hand-held radiation detectors, did not uncover the hidden DU. Monte Carlo analysis of the gamma-ray intensity and spectrum of a DU slug and one consisting of highly-enriched uranium (HEU) showed that DU was a proper surrogate for testing the ability of DHS to detect the illicit transport of HEU. Our analysis using MCNP-5 illustrated the ease of fully shielding an HEU sample to avoid detection. The assembly of an Improvised Nuclear Device (IND) -- a crude atomic bomb -- from sub-critical pieces of HEU ...

Science.gov (United States)

Small metallic fragments can be trapped in combustible cartridge cases during manufacture and released into the interior-ballistic flow upon combustion of the case. Such particles may survive the interior-ballistic cycle and pose an ignition threat to the...

Science.gov (United States)

Research to develop an accurate and reproducible density test for 60-mm and 81-mm mortar propellant increment containers (combustible cartridge cases) was not successful. However, application of modern industrial porosity measurement techniques may afford...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the investigation into the influence of coke pore structure on the formation of nitrogen oxides and carbon monoxide during the combustion of coke. Two samples of coke were compared; pulverized coke and lump coke.

Energy Technology Data Exchange (ETDEWEB)

The effect of combustion conditions on conversion of char nitrogen to N2 was studied in the combustion experiment of char obtained by pyrolysis of coal. Char specimen was prepared by holding ZN coal of Chinese lignite in Ar atmosphere at 1123K for one hour. A batch scale quartz-made fluidized bed reactor was used for combustion experiment. After the specimen was fluidized in reaction gas, it was rapidly heated to start combustion reaction. CO, CO2 and N2 in produced gases were online measured by gas chromatography (GC). As the experimental result, under the incomplete combustion condition where a large amount of CO was produced by consuming almost all of O2, no NOx and N2O produced from char were found, and almost all of N-containing gas was N2. At the final stage of combustion, pyridinic-N disappeared completely, and pyrrolic-N decreased, while O-containing ...

Energy Technology Data Exchange (ETDEWEB)

Car-producers compete in launching hybrids and electric cars, but this does not mean the end for the good old combustion engine.The challenge is the introduction of more complexed costs and weight in the new technology. (AG)

Science.gov (United States)

The beater additive process for manufacturing combustible cartridge cases is superior to the solvent resin, post-impregnation process. However, the current beater additive resins do not produce as good a product as the solvent-resin system. The objective ...

Energy Technology Data Exchange (ETDEWEB)

This book contains 8 papers including the topics of: Spray and Flame Structure in Diesel Combustion; Experimental and Theoretical Investigations of Diesel Injection Transients; Lead-Fuel Governor System - Dual-Fuel Engine; Fuel Spray Modeling in Swirling Flows.

Science.gov (United States)

... CHANNELS, TWO PHASE FLOW, WAVES, IGNITERS, GAS FLOW, HOWITZERS, CARTRIDGE CASES, COMBUSTIBLE CARTRIDGE CASES. ...

Science.gov (United States)

... used their Phoenics code to simulate the effect of additives, such as talcum powder which was impregnated in combustible cartridge cases, on the ...

Science.gov (United States)

... Descriptors : *AMMUNITION, *CONTAINERS, *CARTRIDGES, *COMBUSTIBLE CARTRIDGE CASES, *CARTRIDGE CASES, *ANTITANK ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a nitrogen oxides decreasing combustion method which comprises: a first step of mixing a fuel and air with each other; a second step of bringing the mixture obtained in the first step into contact with a packed catalyst such that only catalytic combustion occurs; and a third step of adding a fresh supply of the fuel to a stream obtained from the second step to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion. The temperature of the packed catalyst is lower than the ignition temperature of the mixture and the adiabatic flame temperature of the mixed gas is lower than a temperature at which the nitrogen oxides occur.

Energy Technology Data Exchange (ETDEWEB)

A dual fuel engine control system for controlling the power output of a dual fuel compression ignition engine. The engine includes mixing means for combining an oxidizer and a primary fuel at a substantially constant ratio of oxidizer to primary fuel. The power output of the engine is controlled through the use of a throttle valve controlling the quantity of combustible mixture delivered to the combustion chamber. The fuel control system minimizes the quantity of ignition fuel required by controlling the quantity of combustible mixture rather than the fuel of air ratio. (author) figs.

Science.gov (United States)

... BODY WEIGHT, FEMALES, SEX, ORGANS(ANATOMY), NITROGUANIDINE, NITROGLYCERIN, COMBUSTIBLE CARTRIDGE CASES, FERTILITY. ...

Science.gov (United States)

... INDUSTRIAL PRODUCTION, MODULAR CONSTRUCTION, IGNITION, PLUGS, NITROCELLULOSE, COMBUSTIBLE CARTRIDGE CASES, FELTS ...

Science.gov (United States)

... reverse aeb 9 nescesmsy amI identify by block number) Provides procedures for evaluating metal, consumable, and combustible cartridge cases. ...

Energy Technology Data Exchange (ETDEWEB)

A phenomenological model is presented for prediction of the combustion characteristics of a quiescent chamber diesel engine. Predictions with the model have shown acceptable agreement with a range of experimental data. The major physical processes controlling combustion have been characterized, and the dominant role of air entrainment and turbulent mixing confirmed quantitatively. 45 refs.

Energy Technology Data Exchange (ETDEWEB)

Since the most efficient way to improve fuel economy in the part-load range is to increase the compression ratio, emphasis is placed on combustion chambers allowing high compression ratios combined with low octane requirements. According to Porsche experience, many demands can be met in the simplest manner by locating the combustion chamber in the piston crown. This configuration offers various advantages over its counterpart installed in the cylinder head. 24 refs.

Energy Technology Data Exchange (ETDEWEB)

From 1965 to 1980 ash content in anthracite from the Donbass supplied to power plants increased from 21.9 to 35.5%, moisture content increased from 7.6 to 10.1%, calorific value declined from 23.7 to 18.5 MJ/kg. Combustion of anthracite culm is stabilized by mazout combustion. Heat treatment of anthracite culm by means of plasma generators improves fuel quality. High temperature causes emission of volatile matter from anthracite and partial gasification of coke particles. Combustion of volatile matter from anthracite and coke is a reliable ignition method for anthracite culm. It also stabilizes combustion of pulverized anthracite. Heat treatment of about 20% anthracite by plasma generators reduces nitrogen oxide emission from a furnace by 30-40%. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The model is also applied to industrial combustor ...

International Nuclear Information System (INIS)

Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and engine operating ...

Energy Technology Data Exchange (ETDEWEB)

The Ministere des Ressources naturelles du Quebec (Quebec Natural Resources Department) implemented a remedial program to treat the waste rock pile at Wood Cadillac, located near Cadillac, in Abitibi, Quebec. The solutions proposed by INRS-Georessources and ENVIROCONSEIL are aimed at eliminating erosion and stabilizing the geochemical processes. Part of the proposed solution also included the use of a reducing trickling filter for the treatment of acid leachates, which also contain arsenic when exiting the waste rock pile. The trickling filter is composed of forest tailings in which the bacteria reduce the sulphates and stimulate the precipitation of arsenic into arsenic sulphates. This is a new treatment that was developed following laboratory experiments which demonstrated the feasibility of the process and quantified the parameters. A demonstration unit was constructed by ENVIROCONSEIL and installed at the Wood Cadillac waste rock pile under the supervision of ...

Energy Technology Data Exchange (ETDEWEB)

Mining operations took place at the Sullivan Mine, located at Sullivan, Abitibi, Quebec between 1930 and 1967 and generated large quantities of tailings. These tailings now represent a waste rock pile in the shape of a delta on the shore of De Montigny Lake. The area covers approximately 50 hectares. When the waste rock pile was first established, several terrestrial and aquatic ecosystems were lost forever. In addition, the very nature of the tailings, combined to the action of the wind and lake, further slow the natural site regeneration. The Ministere des Ressources naturelles du Quebec (Quebec Natural Resources Department) asked Les Consultants en Environnement Argus to prepare a site remediation plan to stimulate the natural regeneration of the ecosystems. It would enable the local fauna to resume its occupation of the territory, while ensuring its proper integration in the environment. The authors described in detail the proposed plan that addresses all the ...

International Nuclear Information System (INIS)

LLNL is developing the nuclear fusion based Laser Inertial Fusion Energy (LIFE) power plant concept. The baseline design uses a depleted uranium (DU) fission fuel blanket with a flowing molten salt coolant (flibe) that also breeds the tritium needed to sustain the fusion energy source. Indirect drive targets, similar to those that will be demonstrated on the National Ignition Facility (NIF), are ignited at #approx#13 Hz providing a 500 MW fusion source. The DU is in the form of a uranium oxycarbide kernel in modified TRISO-like fuel particles distributed in a carbon matrix forming 2-cm-diameter pebbles. The thermal power is held at 2000 MW by continuously varying the "6Li enrichment in the coolants. There are many options to be considered in the engine design including target yield, U-to-C ratio in the fuel, fission blanket thickness, etc. Here we report results of design variations and compare them in terms of various figures of merit such as ...

Energy Technology Data Exchange (ETDEWEB)

This report deals with the renewable energies and the local development called the territory intelligence in action. Taking into account the place of the electricity in the french energy accounting and the part of the nuclear in its production, the local authorities have to act in the heat domain, which is the first energy need in France, far in front of the specific electricity (those which cannot be replace by other type of energy). But 80% of the heat is today covered by fossil energies. No actions to change this situation will be done without a real implication of the local government. The authors preconize an ambitious objective: cover 50% of the heat needs from renewable energies in the next generat This objective must rely on a program called ''alternative energies''. In this framework the authors provide recommendations on the implementation of the renewable energies as an essential challenge for the local authorities. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

ATLAS is one of the four experiments which will take place at the LHC, the CERN future protons collider. This accelerator, which should start in 2007, will allow to continue the studies carried out by its predecessors, as the standard model Higgs boson and new physics searches. The very high luminosity -10 fb{sup -1} during the first three functioning years, then 100 fb{sup -1}- and the 14 TeV in the frame center will ease these studies. The Centre de Physique des Particules de Marseille took part in the ATLAS collaboration, taking in charge half of the End-cap electromagnetic calorimeter modules construction. The description of this sub-detector and the construction steps, in particular the electrical tests which allow the stacking validation, are presented in this document. These tests results, obtained for the live first production modules, are analysed. The pre-series module (module 0) performances, obtained with beam tests performed at CERN in 1999, are also presented. The ...

Energy Technology Data Exchange (ETDEWEB)

The Alice experiment is one of the four main LHC (Large Hadron Collider) experiments. It is dedicated to the study of a new state of matter: the quark gluon plasma, where quarks and gluons are no longer confined within hadrons. In this document, the physics issues that led to the construction of Alice dimuon spectrometer, are described. Then, the research and development on the dimuon spectrometer is presented. The different absorbers are described and experimental tests used to determine their dimensions are presented. The dimuon trigger built using the RPC (Resistive Plate Chamber) streamer mode is then described along with the associated beam and cosmic tests and results. Finally, the tracking system is described in detail and more particularly all its electronics and the first station. The physics constraints on the expected performances of all these systems are clearly defined. (author)

Energy Technology Data Exchange (ETDEWEB)

The work opened by the A.C.R.O. is in line with in an initiative of evaluation of the radiological quality of marine and continental waters of the Normandy coast. In this perspective, measures of radioactivity were made, not near an emissary (already very watched environment) but in more large scale because in marine environment, more than 640 km of coast are concerned. It was a question of supplying a representative assessment of the radioecological situation, for one year,of the marine environment (along the Normandy coast) and main streams which supplies it. (N.C.)

Energy Technology Data Exchange (ETDEWEB)

Preliminary results of studies into penetrant testing at high surface temperature (up to 200 deg.C), are presented. Tests were performed to assess the effectiveness of red dye penetrants using Al and NiCr samples containing artificial as well as natural discontinuities. The test results will be used in due course to formulate a specification for non-destructive testing procedure qualification at non-standard (i.e. outside 16-52 deg.C) temperatures.

Energy Technology Data Exchange (ETDEWEB)

This study shows that the physical conditions necessary for thermal waves to materialize in Dual-Phase-Lagging porous media conduction are not attainable in a porous slab subject to a combination of constant heat flux and temperature (Neumann and Dirichlet) boundary conditions. It is demonstrated that the approximate equivalence between Dual-Phase-Lagging (DuPhlag) heat conduction model and the Fourier heat conduction in porous media subject to Lack of Local Thermal Equilibrium (La Lotheq) that suggested the possibility of thermal oscillations and resonance reveals a condition that cannot be fulfilled because of physical constraints. (author)

Energy Technology Data Exchange (ETDEWEB)

Since a Diesel engine can only be operated always in the condition thinner than the theoretical mixing ratio, a catalytic converter rhodium cannot be used, hence it is impossible to oxidate the portion of incomplete combustion and resolve nitrogen oxides using the catalytic converter rhodium as a spark ignition engine. Also since its combustion is mainly diffusion combustion, the amount of generated soot and fine particles is as much as several times to ten times more than that of a spark ignition engine. Also since no after treatment of exhaust has been established for a Diesel engine, it is necessary to cope with the combustion process which is the source of generating pollutant in order to promote reduction of such pollutant. In this article, awaring of the above, the difficulty of achieving both reduction of fine partiicles and reduction of NO {sub x} at the same time is explained in detail, and ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, the combustible value (i.e. 100-Ash) and combustible recovery of coal flotation concentrate were predicted by regression and artificial neural network based on proximate and group macerals analysis. The regression method shows that the relationships between (a) in (ash), volatile matter and moisture (b) in (ash), in (liptinite), fusinite and vitrinite with combustible value can achieve the correlation coefficients (R{sup 2}) of 0.8 and 0.79, respectively. In addition, the input sets of (c) ash, volatile matter and moisture (d) ash, liptinite and fusinite can predict the combustible recovery with the correlation coefficients of 0.84 and 0.63, respectively. Feed-forward artificial neural network with 6-8-12-11-2-1 arrangement for moisture, ash and volatile matter input set was capable to estimate both combustible value and combustible recovery with ...

Energy Technology Data Exchange (ETDEWEB)

In this article, we review and clarify some of the points made by previous authors regarding chemical looping combustion (CLC). While much of the recent interest in chemical looping combustion has been associated with carbon sequestration, our primary interest here is its potential to increase the thermodynamic efficiency of converting fuel chemical energy into useful work. We expand on several points about the details of CLC that we feel have not previously been sufficiently explored, and suggest alternative (and possibly more practical) approaches that exploit some of the same thermodynamic concepts. We illustrate our key points with {First} and {Second} Law analyses of ideal conceptual processes, which in addition to {CLC} also include isothermal, non-equilibrium, preheated combustion and combustion with thermochemical recuperation. Our results suggest that a significant portion of the potential ...

Energy Technology Data Exchange (ETDEWEB)

The authors experimentally study the separate stages of the determination of iodine in thyroidin by the combustion method in a flask with oxygen. The monotypic, conventional procedures and the procedure of Kolii and Pakhomov were studied. With addition of potassium iodide, a sixfold amount (compared with the initial) of iodine is liberated. Further, the liberated iodine is titrated by sodium thiosulfate. The authors find the degree of influence of a high nitrogen content on the determination of iodine in organic compounds. The procedure developed for the quantitative determination of the iodine in thyroidin by the combustion method is simple, fairly rapid, and can be used for the reliable control of the quality of thyroidin preparations and its starting raw material.

Energy Technology Data Exchange (ETDEWEB)

An improved hybrid solar/combustion powered receiver of the type having an insulated housing with a front end and a rear end, a heat exchanger positioned adjacent the rear housing end for extracting heat energy out of the receiver, the insulated housing surrounding the heat exchanger and forming a receiver cavity, the housing also including an aperature having an aperture axis, the aperture located in the front housing end for admitting solar radiation to the cavity to impinge upon the heat exchanger, and a plurality of gas burners to provide combustion gases within the receiver.

Energy Technology Data Exchange (ETDEWEB)

Combustion performance trials were conducted on a commercial sample of Coal Valley coal from the Coalspur coalfield in the foothills region of Alberta. The project included an analytical investigation of the coal and coal ash properties as well as combustion studies in the CCRL pilot-scale, pulverized coal-fired boiler, under conditions representative of those in large steam boilers. This report gives the objectives of the project, the analyses of the coals, and describes the facilities and operational procedures. An evaluation of the experimental results and the conclusions are presented.

Energy Technology Data Exchange (ETDEWEB)

Convective cooling of turbine hot parts using a closed loop system is disclosed. Preferably, the present invention is applied to cooling the hot parts of combustion turbine power plants, and the cooling provided permits an increase in the inlet temperature and the concomitant benefits of increased efficiency and output. In preferred embodiments, methods and apparatus are disclosed wherein air is removed from the combustion turbine compressor and delivered to passages internal to one or more of a combustor and turbine hot parts. The air cools the combustor and turbine hot parts via convection and heat is transferred through the surfaces of the combustor and turbine hot parts.

Energy Technology Data Exchange (ETDEWEB)

The coal-fired combined cycle with partial gasification and fluidized bed combustion (PGFBC-CC), also referred to as a hybrid cycle, has advantages of staged energy conversion and utilization, which can attain high thermal efficiency with low emissions. Four kinds of PGFBC-CC are studied in this paper, two based on pressurized fluidized bed combustion (PFBC) and two on atmospheric fluidized bed combustion (AFBC). Thermal performance calculations and parametric analyses were performed. On the basis of the results, from the above analyses, the best integration system for China is suggested. In addition, a preliminary exergetic analysis is carried out for three of the PGFBC-CC variants.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Very important performances in the practical use of solid propellants are combustion and physical properties. Among the present solid propellants, composite propellants used ammonium perchlorate (AP) as oxidizers are adopted widely now due to these excellent performances. Recently, a combination of ammonium nitrates (AN) as oxidizers and azido polymers as binders in expected as the propellants which control decrease of combustion properties and satisfy unsensitivity. However, in order to use these azido polymers/AN propellants in practice, further, it is necessary to improve the specific impulse and the burning rate. In this report, aiming to improve the combustion properties of BAMO/NMMO/AN propellants, the sensitivity and the combustion properties of propellants added high energetic plasticizers in binders, further, displaced a part of AN to cyclotetramethylenetetranitramine (HMX) and double based ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses the development and demonstration of innovative combustion technologies that improve energy conservation and environmental practices in the US industrial sector. The report includes recommendations by industry on R&D needed to resolve current combustion-related problems. Both fundamental and applied R&D needs are presented. The report assesses combustion needs and suggests research ideas for seven major industries, which consume about 78% of all energy used by industry. Included are the glass, pulp and paper, refinery, steel, metal casting, chemicals, and aluminum industries. Information has been collected from manufacturers, industrial operators, trade organizations, and various funding organizations and has been supplemented with expertise at the Idaho National Engineering Laboratory to develop a list of suggested research and development needed for each of the seven industries.

Science.gov (United States)

The initial phase of this study consisted of a survey of existing FGD systems used on larger combustion processes in the NATO countries and Japan.

Energy Technology Data Exchange (ETDEWEB)

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

International Nuclear Information System (INIS)

A chemical-looping process is proposed for the clean combustion of solid fuels for electric power or heat generation. The process is based on coal gasification with CO_2 to produce CO. The CO then reduces CaSO_4, which is used as an oxygen carrier, in a separate reactor to give CaS and CO_2. A portion of the CO_2 is recycled for the gasification stage and the rest can be sent for sequestration. The CaS is sent to another reactor for oxidation with air and to generate heat or power. The overall thermal effect is the same as direct combustion, but separation of CO_2 and other pollutants, such as sulphur, is achieved. In comparison with conventional chemical-looping combustion of natural gas, much less water is present in the CO_2 product, and hence the loss of heat energy and corrosion of the fuel-reactor system can be reduced.

British Library Electronic Table of Contents (United Kingdom)

In this study a novel sol-gel auto-combustion method, using n-decyltrimethylammonium bromide as a cationic surfactant, has been used to synthesize strontium hexaferrite nanocrystalline powder. The dried nitrate-citrate gel, prepared from a solution of ferric nitrate, strontium nitrate, citric acid, trimethylamine and cationic surfactant, exhibited an auto-combustion behavior after ignition in air. The formation reaction temperature, phase identification, crystallites size, particles size distribution and morphology of resultant strontium hexaferrite powder were investigated by DTA/TGA, FTIR, XRD, LPSA, TEM and SEM techniques. The results showed that in presence of the cationic surfactant, the combustion intensity increases and the crystallite size decreases. The crystallite size of stronti...

International Nuclear Information System (INIS)

A rapid combustion unit (Baird and Tatlock) incorporating a combustion chamber provided with baffle plates for complete combustion of the sample without the use of a catalyst has been assembled in a glove box for the determination of carbon and hydrogen in actinide complexes. The unit has been modified employing a movable electric furnace and a proportional temperature controller, for decomposition of the sample at desired heating rates. The set-up was standardised employing various reference materials such as benzoic acid, acetanilide, sulphanilamide and 1-chloro 2:4 dinitrobenzene and the standard deviation in the measurements evaluated. It has also been used successfully for the determination of carbon in uranium carbide and carbon and hydrogen in some uranyl-#beta#-diketone-amine N-oxide complexes and in plutonium(IV) oxalate. (auth.).

Energy Technology Data Exchange (ETDEWEB)

A new air injection process called toe-to-heel air injection (THAI) has been developed to achieve very stable combustion performance in heavy oil wells by controlling gas override. In the THAI process, injected air migrates preferentially to the combustion front into a horizontal producer well by the oxygen diffusional gradient created under steady state conditions. This is possible because of the balance between the stoichiometric oxygen flux needed to burn the fuel (coke) laid down ahead of the combustion front and the removal of downstream combustion gases and mobilised fluids. This study involved a numerical simulation of the THAI process to increase the understanding of the processes involving fluid flow, heat transfer and chemical reactions taking place during in situ combustion. Two tests were conducted involving one dry and one wet combustion using heavy ...

Energy Technology Data Exchange (ETDEWEB)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80{sup +}{trademark} Standard Design. This volume 9 discusses Electric Power and Auxiliary Systems.

International Nuclear Information System (INIS)

This report, entitled Combustion Engineering Standard Safety Analysis Report -- Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80"+trademark Standard Design. This volume 11 discusses Radiation Protection, Conduct of Operations, and the Initial Test Program.

Science.gov (United States)

Gas fired radiant tube heaters provide an indirect heating source for applications in which direct contact cannot be permitted between combustion gases and the workpiece. The program was an investigation of ways to improve performance of such burners thro...

International Nuclear Information System (INIS)

The study of the melting of combustible rods is of great importance for the safety analysis of nuclear reactors. Due to the special characteristics of the problem, a sharp interface between the solid and liquid region does not exist, but appears a 'mushy' region in which the material is partially melted. The Finite Element Method is employed here, together with a regularized enthalpy formulation. Finally, the results obtained are presented and discussed. (Author).

Energy Technology Data Exchange (ETDEWEB)

This document contains the outline and viewgraphs used in the speech. Topics covered are: conventional oil and gas recovery; unconventional oil and gas sources; oil shale resources; conventional coal combustion; advanced fossil power systems; fluidized bed combustion; coal/oil or coal/water mixtures; and gaseous and liquid fuels from coal. (DMC)

Energy Technology Data Exchange (ETDEWEB)

This investigation involves a study of the influence of key processing parameters on the heating of materials using microwave energy. Selective and localized heating characteristics of microwaves will be utilized in the sintering of ceramics without hydrostatic pressure. In addition, combustion synthesis will be studied for the production of powders, carbides, and nitrides by combining two or more solids or a solid and a gas to form new materials. The insight gained from the interaction of microwaves with various materials will be utilized in the mobilization and subsequent redeposition of uranium.

Science.gov (United States)

The paper describes the Integrated Air Pollution Control System (IAPCS), a computerized program that can be used to estimate the cost and performance of pre-combustion, in situ, and post-combustion air pollution control configurations in pulverized-coal-fired utility boilers of 1...

Energy Technology Data Exchange (ETDEWEB)

Spark ignition internal combustion engines perform satisfactorily when the fueled with biomass producer gas from a fluidized bed gasifier. Although power output is reduced compared to natural gas levels, full power recovery can be achieved with a relatively low level of supercharging. Important considerations are an adequate fuel delivery system and adquate gas cleaning. ref.

Science.gov (United States)

Studies in advanced coal research are presented. Included are the following: coal science programs; coal preparation and combustion kinetics; advanced technology in liquefaction, including direct and indirect liquefaction; alternative fuels; advanced combustion technology; flue gas cleanup; environmental coordination, technology transfer, and clean coal demonstration program. (CBS)

Energy Technology Data Exchange (ETDEWEB)

The effects of compression ratio on the history of the fuel-burning process was investigated in a single-cylinder direct-injection diesel engine. Two compression ratios of 21.4 and 18.5 were studied by using two wide and shallow bowls. The engine was operated at different speeds and overall air-fuel ratios, but with constant start-of-combustion timing at top dead center. The measured cylinder pressure was used to derive fuel-burning rate. At all conditions, the low-compression-ratio bowl had a larger mass of premixed-burned fuel and a higher peak specific fuel-burning rate. The fuel-burning rate in the diffusion-controlled phase of combustion decreased with decreasing compression ratio. The resulting combustion duration became longer at reduced compression ratio, and the difference could be as large as 14 crank-angle degrees. For the engine conditions examined in this study, the mass of fuel present in the ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the combustion experiments performed using the SP Industry Calorimeter. In addition to measuring parameters such as heat release rate (HRR), mass loss rate, effective heat of combustion and smoke obscuration, considerable effort was put into the characterisation of the smoke gases in order to obtain a basis for evaluations of the toxic potency of the smoke. The materials studied were Nylon 66, polypropene, polystyrene (with and without fire retardant, respectively), PVC and chlorobenzene. A total of 19 large-scale, well ventilated combustions were carried out. The mass of sample burned ranged from 20 kg to 125 kg in an experiment. A procedure was designed for cleaning the smoke gas duct between experiments and was found to be effective. Measurements were carried out for the amounts of O{sub 2}, CO{sub 2}, CO, NO{sub x}, THC (unburned hydrocarbons), HCN, HCl, NH{sub 3} and individual organic compounds ...

Energy Technology Data Exchange (ETDEWEB)

Combustion scientists are primarily concerned with the fuels most often burned as energy sources (coal, petroleum products, and natural gas), with the goal of learning to burn them as efficiently, intensely, and cleanly as possible. Discovering those slight rearrangements of chemical bonds that together account for the net chemical transformation is the key to understanding how combustion proceeds. Once these reactions have been defined, the chemist can determine the rate coefficient of each reaction as a function of temperature and assemble the information into flame models. The computer programs that use these models to predict experimental results combine two sets of equations describing (1) the diffusive and reactive rates of change in concentration of all the molecules in the flame and (2) the flow of the reacting gases. Although the details of hydrocarbon-flame models are still disputed, many of their general features are clear and the ...

Energy Technology Data Exchange (ETDEWEB)

Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 58% for electric power generation. Nevertheless the reserves of natural gas are more limited compared to the reserves of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverised coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, a catalyst, that converts carbon monoxide and unburnt carbon to carbon dioxide ...

Energy Technology Data Exchange (ETDEWEB)

The results of an experimental investigation of the performance of a small bore engine with a swirl chamber when operating as a dual fuel engine with commercial methane as the gaseous fuel were presented in this paper. The experiment involved using a 3-dimensional computational fluid dynamics model to predict the performance of the engine. A detailed chemical kinetics for the gaseous fuel component, consisting primarily of methane and a reduced detailed chemical kinetics for the diesel fuel while considering the turbulent combustion processes an associated performance of a dual fuel engine with a swirl chamber were incorporated in the simulation. The study experimentally and numerically investigated the effects of changes in the quantities of the liquid fuel pilot and gaseous fuels on the combustion processes, engine performance, cyclic variations, and emissions. The paper discussed the experimental approach and results. It also discussed the ...

Energy Technology Data Exchange (ETDEWEB)

Objective: Optimization and testing of a high temperature combustion chamber for burning coal gas and conventional fuels natural gas or fuel oil. Coal gas is not available in such quantity for testing a full scaled combustion chamber. Therefore the design of the combustion chamber is based of experimental results from model tests and numerical solution procedures. Working program: (1) Analytical model for burning coal gas implemented in an existing computational fluid dynamics (CFD) code. (2) Three-dimensional calculations of a full scaled combustion chamber with a CFD code for flows accompanied by combustion and chemical reaction. (3) Improvement of measuring method for determination of flame temperature and concentration. (4) Temperature and concentration profil measuring in a full scaled combustion chamber by operating with natural gas or fuel oil. Results: ...

Energy Technology Data Exchange (ETDEWEB)

The patient positioning and repositioning control in radiation therapy all along the treatment can be conducted using a variety of X-ray sources and imaging detector devices. The development of image guided radiation therapy techniques leads to more frequent use of this imaging control. In this article we summarize the current methods for measuring the dose delivered by X-ray imaging devices used in radiation therapy, as well as basic proposals to take account of these imaging doses for prescribing, recording and reporting radiation therapy treatment. (authors)

Energy Technology Data Exchange (ETDEWEB)

Mining of copper and zinc took place at the Clinton Mine located in the Estrie region of Quebec between 1973 and 1975, during which time 115,000 tons of mineral were treated at the Solbec plant. In this poster presentation, the authors provided the background information pertaining to this mine and described the state in which it was in 1994. The pit was covered with good quality water, with a pH of 7,1 and copper and zinc content ranging between 0,1 and 0,6 mg/l, and iron ranging between 0,2 and 1,8 mg/l. The tailings basin drainage was found to have a pH of between 3,6 and 6,1. A program for the characterization of the site was implemented and the concept for the restauration of the Clinton site was developed and implemented. The work carried out at the site is discussed during this presentation as well as the monitoring taking place. 27 figs.

British Library Electronic Table of Contents (United Kingdom)

ResumeLa convergence des solutions faibles du systeme de Navier-Stokes-Fourier-Poisson compressible avec un terme de frottement est etudiee dans la limite dun frottement infini, la loi de pression incluant, comme cas particulier, celle correspondant aux particules de Fermi-Dirac. La limite se trouve etre une solution faible dun systeme de Smoluchowski-Poisson non isotherme, la temperature ne dependant que de la variable temporelle et etant determinee par la conservation de lenergie totale.

Energy Technology Data Exchange (ETDEWEB)

The law of the 30 December 1991 on the high activity long lived radioactive wastes reached the end. This synthesis final document presents the scientific and technological results, obtained still the end of 2005, on the separation and the transmutation of long lived radionuclides of high activity long lived radioactive wastes. It is organized in five chapters: a presentation of the context and the historical aspects, the researches, the objectives and the strategy of the axis 1, the researches results on the advanced separation, the researches results on the transmutation, the scenario of separation-transmutation and their environmental, technical and economical impacts. (A.L.B.)

British Library Electronic Table of Contents (United Kingdom)

Beaked whales (Ziphiidae) often show highly specialized features, involving bone morphology or structure, in the rostral region of their skulls. Previous studies revealed an extremely derived and peculiar histological structure in the rostrum of the extant Mesoplodon densirostris. In order to assess if this structure is a general feature of ziphiids, the swollen premaxillae of Aporotus recurvirostris, a Miocene species from the North Sea, were studied histologically. These bones are pachyostotic and strongly osteosclerotic. However, their structural organization is entirely different from that of M. densirostris rostrum: they are basically made of a non-remodeled, laminar tissue that was cyclically deposited by the periosteum. As compared to the generalized structure of the premaxillae of ...

Energy Technology Data Exchange (ETDEWEB)

This evaluation has for object to inform about the levels in carbon 14 in the environment of the factories of La Hague. Two sectors were differentiated on one hand the terrestrial environment, and on the other hand the marine environment. The investigations concerned first and foremost food products stemming as the vegetable culture (vegetables) or individual breeding (milk, eggs) but also foodstuffs stemming from the local agriculture (cereal). In touch with the second sector, the marine environment, the sampling concerned the accessible products of the sea by all and those locally marketed (fishes, molluscs, shellfishes). The different results are presented in tables. (N.C.)

International Nuclear Information System (INIS)

Purpose: The purpose of this study was to evaluate the efficacy and toxicity of replication-competent adenovirus-mediated double suicide gene therapy in an adjuvant setting with external beam radiation therapy (EBRT) in an experimental prostate cancer model in preparation for a Phase I clinical study in humans. Methods: For efficacy studies, i.m. DU145 and intraprostatic LNCaP C4-2 tumors were established in immune-deficient mice. Tumors were injected with the lytic, replication-competent Ad5-CD/TKrep adenovirus containing a cytosine deaminase (CD)/herpes simplex virus thymidine kinase (HSV-1 TK) fusion gene. Two days later, mice were administered 1 week of 5-fluorocytosine + ganciclovir (GCV) prodrug therapy and fractionated doses of EBRT (trimodal therapy). Tumor control rate of trimodal therapy was compared to that of EBRT alone. For toxicology studies, immune-competent male mice received a single intraprostatic injection (10"1"0 vp) of the replication-competent ...

Energy Technology Data Exchange (ETDEWEB)

The paper present the results of the study on D.U. (depleted uranium) contamination in the environment and possible effects on animal healths in the region o f Bujanovac. Samples of soil, feed, leaves, grass, lichen, moss, honey and water were collected randomly in 2003/2004 in the vicinity of the target area (500-1000 m) and 5 km from the target area. Activity of the radionuclides ({sup 226}Ra, {sup 232}Th, {sup 40}K, {sup 210}Pb, {sup 238}U, {sup 235}U, {sup 137}Cs, {sup 7}Be) in soils, grass, lichen, moss and honey was determined on Hp Ge detector (Canberra, relative efficiency 23%) by standard gamma spectrometry. Total alpha and beta activity in water was determined on proportional alpha/beta counter (Canberra 2400, efficiency for alpha emitters 11%, efficiency for beta emitters 30%). Non significantly higher values of concentrations of {sup 226}Ra, {sup 232}Th, {sup 238}U and {sup 235}U were measured in the immediate vicinity of the targeted site, but {sup ...

British Library Electronic Table of Contents (United Kingdom)

Pyogenic sacroiliitis is a rare entity in children. Diagnosis is often delayed because of its variable clinical presentation, low suspicion by the examining physician, and rare findings on radiographs. Delayed diagnosis, however, results in complications such as iliopsoas abscess. We report the case of a 12-year-old girl hospitalized with a 21-day history of fever, pain in the left iliac fossa, and flexion contracture of the hip. On examination, she had fever (38.9 ^oC), psoitis, localized tenderness at the left sacroiliac joint, and pain elicited by lateral compression of the pelvis. The abdominal examination was normal. The erythrocyte sedimentation rate was 130mm in the first hour, C-reactive protein was 186mg/l, and the white blood cell count was 18,400/mm^3, with 79% neutrophils. Urin...

British Library Electronic Table of Contents (United Kingdom)

In this paper, the unsteady MHD free convection heat and mass transfer of viscous fluid flowing through a Darcian porous regime adjacent to a moving vertical semi-infinite plate under Soret and Dufour effect have been examined. Viscous dissipation effects are included in the energy equation. A uniform magnetic field is applied transversely to the direction of the flow. The differential equations governing the problem have been transformed by a similarity transformation into a system of non-dimensional differential equations which are solved numerically by element free Galerkin method. The influence of Grashof number (Gr), magnetic parameter (M), heat absorption parameter (Q), permeability parameter (K), Schmidt number (Sc), Soret number (Sr), and Dufour number (Du) on the velocity, tempera...

Energy Technology Data Exchange (ETDEWEB)

Fuel spray and air motion characteristics and combustion in direct injection (DI) diesel engines was studied using computational models of the commercial CFD-code FIRE. Physical subprocesses modelled included Lagrangian spray droplet movement and behaviour (atomisation, evaporation and interaction of spray droplets) and combustion of evaporated liquid spray in the gas phase. Fuel vapour combustion rate was described by the model of Magnussen and Hjertager. The standard k,{epsilon}-model was used for turbulence. In order to be able to predict combustion accurately, the fuel spray penetration should be predicted with reasonable accuracy. In this study, the standard drag coefficient had to be reduced in order to match the computed penetration to the measured one. In addition, the constants in the submodel describing droplet breakup also needed to be adjusted for closer agreement with the measurements. The ...

British Library Electronic Table of Contents (United Kingdom)

In this work, a new sol-gel auto-combustion method has been performed to synthesize single phase nickel ferrite nanocrystalline powders by using n-cetyltrimethylammonium bromide, as a cationic surfactant. The gels were prepared from ferric and nickel nitrates and citric acid. Ammonia was used as pH adjusting agent as well. The effects of the surfactant on the after combustion calcination process and the reduction of the resulting powder crystallite size which affects the magnetic properties of the material were investigated by XRD and DTA/TGA techniques. The results showed that the ignition of the gels in air have a self-propagating behavior. Addition of surfactant to the starting solution affected the crystallite size of the synthesized powders and their phase constitution. The crystallit...

Energy Technology Data Exchange (ETDEWEB)

Effects of combustion conditions on the critical calorific value of flame blowout were reported for low calorific gas on the assumption of using coal derived gaseous fuel. Further, calculations of adiabatic flame temperature by using chemical equilibrium calculation were conducted in order to get a possibility of increasing exit gas temperature of gas turbine combustor to 1,300 C for low calorific value gas fuel. As a result, effects of (1) fuel composition, (2) preheating fuel temperature, (3) calorific value, and (4) combustion air velocity and fuel nozzle diameter, on the critical calorific values of flame blowout were clarified. In increasing exit gas temperature of gas turbine combustor to 1,300 C when using low calorific value gas fuel, it is essential to get an advanced cooling technology for the gas turbine combustor.

Energy Technology Data Exchange (ETDEWEB)

This is a process for the manufacture of a filter material for cleaning industrial or internal combustion engine exhaust gases and filter material manufactured according to the process. The filter material is manufactured from the mineralized combustion product of peel of tropical fruits burnt at a temperature of 820/sup 0/C to 840/sup 0/C in an oxidising atmosphere excluding the production of carbon, particularly using banana skins and orange peels, which product is granulated with carrier materials or compressed.

Energy Technology Data Exchange (ETDEWEB)

Turbulent premixed methane-air combustion in a cylindrical chamber is numerically simulated considering radiation effect. Reaction rates are considered as minimum rates between Arrhenius rates and eddy break up rates. A five step reduced mechanism is used. Turbulent modeling is done via standard k-{epsilon} model imposed by empirical inlet boundary conditions. Source terms of energy equation consist of reaction rates and radiation effects. The discrete ordinate method (DOM) is employed to solve the radiative transfer equation (RTE) and the weighted sum of gray gas model (WSGGM) is imposed to consider radiation effect of non-gray gases. The results indicate that in the case of turbulent combusting flows, the effect of radiation of gases can affect the temperature and species concentrations. The numerical results obtained considering radiation effect are closer to the experimental data than that of the case without radiation effect. (author)

International Nuclear Information System (INIS)

The production of atmospheric pollutants in combustion processes depends on plant characteristic, combustion conditions and fuel quality. The influence of fuel quality on the emission of sulphur oxides, nitrogen oxides, carbon monoxide, dust and carbon dioxide and on the emission of some toxic pollutants, such as heavy metals and polycyclic aromatic hydrocarbons, is analysed. The comparison between the emission limits, fixed by the Italian legislation, and the uncontrolled pollutant emissions, produced by fossil fuel combustion in power plants and industrial use, shows that, in order to comply with the limits, a reduction of pollutant emissions is required through the use of abatement systems and cleaner fuels where natural gas has a primary role. The use of cleaner fuels is particularly required in heating plants and appliances for the residential sector, where the development of new gas technologies further increases the ...

British Library Electronic Table of Contents (United Kingdom)

The major bottleneck for popularization and utilization of the conventional mechanical valve pulse combustors is the self-priming mode of gas supply. An aerodynamic valve (as against mechanical valve) self-excited pulse combustor of the Helmholtz-type with continuous supply of gas and air was designed and a mathematical model was established in this paper. The theoretical model employed well-stirred reactor model and a single step Arrhenius chemistry, and took those factors which might affect the combustion stability into account. The factors include the variation of the mass rate of the reactants affected by the pressure in the combustion chamber, the convective and radiation heat loss in the combustion chamber, and the heat transfer and wall friction in the tailpipe. The effect of wall t...

International Nuclear Information System (INIS)

With the assistance of mechanical activation, yttrium-stabilized #alpha#-SiAlON was prepared by combustion synthesis in air, instead of high-pressure N_2 atmosphere for the first time. The reaction activity of metallic particles was remarkably enhanced by mechanical activation, which conduced the reduction of grain size, increased the total surface area and formation of fresh surface. The formation of #alpha#-SiAlON by combustion synthesis in air was explained by a kinetically induced reaction mechanism, in which both initial formation of #alpha#-SiAlON and following avoidance of oxidation were fulfilled by the retardation of O_2 infiltration owing to the short reaction period and fast cooling rate.

British Library Electronic Table of Contents (United Kingdom)

Ramjet burners are known to produce highly unsteady operating conditions with strong couplings between combustion, acoustics and flow dynamics. Predicting such operating limit-cycles still remains a difficult task for Computational Fluid Dynamics (CFD) although recent use of Large Eddy Simulation (LES) clearly opens new possibilities. The main difficulties for LES are to properly address numerically specific flow features at the same time. For example, a proper representation of the acoustic ramjet eigenmodes necessitates for the solver to be able to treat shocks often present at the inflow conditions without interfering with the low Mach number flow in the region of combustion. Chemistry modelling is another difficulty and it is still not clear what level of description is sufficient to r...

Energy Technology Data Exchange (ETDEWEB)

An intake system is described for a direct fuel injection diesel engine having a cylinder block, at least one cylinder in the cylinder block, a piston in the cylinder having a recess on a top surface thereof, a cylinder head mounted on the cylinder block on top of the cylinder, a fuel injector adapted to directly inject fuel into a combustion chamber formed between the lower side of the cylinder head and the recess on the top surface of the piston, and below the injector, and a single exhaust passage opening to the combustion chamber at a location near the injector, the intake system comprising first and second intake passages in the cylinder head, the first and second intake passages are independent of each other and adapted to introduce air into the combustion chamber. The controller means are coupled to the second intake passage for controlling the flow of air therethrough.

Energy Technology Data Exchange (ETDEWEB)

The unburned HC in a direct-injection diesel engine is a cause of exhaust odor and SOF emission. Reduction of HC by changing the injection nozzle specifications was attempted in previous studies. In this study, some experiments in which the mixture formation was varied by using different hole diameters in a multihole nozzle and spray angles to the combustion chamber wall have been conducted. When the diameter of injection holes, which influences the fuel adhering to on the cylinder head walls and the combustion chamber wall, becomes smaller, the HC emission in the idling condition, HC deviation from cylinder to cylinder and HC increase with long idling time are decreased. The same effects were obtained by decreasing the diameter of all holes and by injecting the spray downward to the combustion chamber. 13 refs., 13 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period October 1, 2004 through December 31, 2004. The following tasks have been completed. First, the renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have proceeded well. Second, the detailed design of supporting and hanging structures for the CFBC was completed. Third, the laboratory-scale simulated fluidized-bed facility was modified after completing a series of pretests. The two problems identified during the pretest were solved. Fourth, the carbonization of chicken waste and coal was investigated in a tube furnace and a Thermogravimetric Analyzer (TGA). The experimental results from this study are presented in this report. Finally, ...

Energy Technology Data Exchange (ETDEWEB)

The combustion characteristics of a turbocharged natural gas and diesel dual-fuelled compression ignition (CI) engine are investigated. With the measured cylinder pressures of the engine operated on pure diesel and dual fuel, the ignition delay, effects of pilot diesel and engine load on combustion characteristics are analysed. Emissions of HC, CO, NO{sub x} and smoke are measured and studied too. The results show that the quantity of pilot diesel has important effects on the performance and emissions of a dual-fuel engine at low-load operating conditions. Ignition delay varies with the concentration of natural gas. Smoke is much lower for the developed dual-fuel engine under all the operating conditions. (Author)

Energy Technology Data Exchange (ETDEWEB)

Combustion characteristics of Korean anthracite in a circulating fluidized bed and freeboard were investigated. A test coal was selected with heating value of 4,429kcal/kg and ash content of 38%. Characteristics of combustion, sorbent effect on desulphurisation and emission of SO{sub x} and NO{sub x} were monitored by varying process variables such as feed rate, (Ca+K)/S ratio, and excess air ratio at the given properties of coal. Optimum operating conditions were studied by analysing: axial profiles of temperature, effect of excess air ratio, characteristics of loopseal and bag filter ashes, and emission of toxic gases. 9 refs., 9 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

A multi-zone computational model in conjunction with some engine tests are used to examine the combustion process of gas fueled diesel engines common known as dual fuel engine to provide information about details of the production of exhaust emissions, especially at light load when very lean mixtures are employed. Detailed chemical reaction kinetic simulation is employed for each of these individual combustion zones so as to establish the associated temporal variations in the concentrations of reacting species right to the exhaust stage. The influence of changes in major operating and design parameters such as the concentration of the gaseous fuel in the cylinder charge, intake temperature and the size of the diesel pilot fuel employed on the production of the exhaust emissions are examined. It is demonstrated in general that any measure that tends to increase the size of the combustion regions within the overly lean ...

Energy Technology Data Exchange (ETDEWEB)

Except nuclear industry, diverse structures (hospitals, of research or manufacturers) can have appeal to the use of radioisotopes conditioned under unsealed shape. Such practices lead to tolerate releases in environment in the respect of a statutory device. So the collective network can contain radioisotopes the future of which is going to depend partially on the cleaning applied to waste water. This study through the analysis of a concrete case, has for objective to inform about the future of gamma radioelements present in waste water treated by a wastewater treatment plant. The contamination of the network is essentially due to Tc{sup 99} and I{sup 131}, radioelements present whatever the working day and the hour considered. The total estimated in-load for a day is important, of the order of 4000 MBq for Tc{sup 99} and 15 to 300 MBq for I{sup 131}. The assessment of cleaning of the station shows that this one plays a role towards this pollution through these stages of treatment. ...

International Nuclear Information System (INIS)

Full text: Many factors including drug efficacy, compliance and antibiotic resistance may influence HP eradication rates. The "1"4C urea breath test is a sensitive method of confirming HP colonisation and eradication. The aim was to study the relationships between the peak "1"4CO_2 counts on the breath test prior to treatment, smoking and HP eradication, and to assess if persistent or recurrent symptoms implied failure of eradication. 117 patients with DU and HP colonisation proved on biopsy or rapid urease test who underwent "1"4C urea breath tests at least one month after eradication treatment was ceased were studied (69 male, 48 female, mean age 41, range 26-87 y). Questionnaire assessment of treatment regimen, smoking history and dyspeptic symptoms was made at the time of the breath test. A sub-group of 43 patients who had pre- and post-treatment breath tests was studied to assess if high peak "1"4CO_2 counts on the pre-treatment breath test related to ...

International Nuclear Information System (INIS)

This report has been prepared in support of the industry effort to standardize nuclear plant designs. These documents describe the Combustion Engineering, Inc. System 80+trademark Standard Design.

Science.gov (United States)

Test firings of 120-mm rounds were performed to characterize effects due to the combustible cartridge cases used. Comparisons were made between measured ballistic parameters, especially gas pressures, and those predicted by computerized simulation calcula...

Science.gov (United States)

Radiation Measurement in Crew Compartment. DTO 805: .... spacecraft and aircraft propulsion, and hazardous waste disposal. ...... combustion reactions in a turbulent chemical kinetic flow reactor using laser induced fluorescence and ...

Energy Technology Data Exchange (ETDEWEB)

A hydrogen peroxide injection system was designed and installed in the stack of a 5,274 million J/hr industrial pilot plant scale combustion chamber using natural gas as fuel. The concentration of peroxide in the gas stream was precisely controlled by continuous injection using an electromagnetic dosage pump, the liquid 50% peroxide solution was finely dispersed into the gases by a water cooled custom designed delivery system with a spray nozzle at the tip. Residence times between 0.1 and 1.8 seconds and concentrations of H{sub 2}O{sub 2} between 280 ppm and 4,000 ppm were used during the test runs. CEMS for total hydrocarbons, carbon monoxide, nitrogen oxides, as well as an ultrasonic gas flow monitor were used to measure the effect of hydrogen peroxide in reducing the emissions of these pollutants. Destruction removal efficiencies between 25% and 100% were observed for hydrocarbons, and concentrations of CO, as well as NO{sub x}. were reduced about 50%. The ...

Energy Technology Data Exchange (ETDEWEB)

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarily at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report covers the reporting period 1 April to 30 June 2003 in which PSI, Aquasearch and University of Hawaii conducted their tasks. Based ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the effects of SiC coating on the oxidation resistance of C/C composites in combusting fields, which are expected to be applied to high temperature structural materials at over 1770K. The coating methods employed were CVD and pack cementation. The time changes in weight loss of the specimens were measured at temperatures of 1770K and 1900K under the equivalence ratio of 0.9 generated by methane-air combustion, and the surface of the specimens before and after the experiment was observed by SEM. Although the weight loss of the specimens coated by the CVD method was minimal, the coating layer was easily peeled off from the substrate. On the other hand, the layer of the specimens coated by the pack cementation method was stable and adhered to the substrate, but the substrate was degraded because of penetration of oxygen through the pores in the layer. To cover the pores, the specimens were additionally coated with glass ...

Energy Technology Data Exchange (ETDEWEB)

The physicochemical nature of a silicoaluminophosphate with the faujasite structure has been studied. The molecular sieve framework contains a homogeneous distribution of silicon, aluminum, and phosphorus and is negatively charged. Combustion in air of the charge-compensating organic cations produces hydroxyl groups which exhibit Broensted acidity.

Science.gov (United States)

A cartridge case is made by making up an aqueous slurry of cellulosic fibers, forming the fibers into a mat and molding the mat or preform into final shape by use of a die at up to 165 degrees F.

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy`s Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional burners and also indicated favorable economics for replacement of oil- and gas-fired ...

Energy Technology Data Exchange (ETDEWEB)

Problems with the refractory liners of incinerator combustion chambers have accompanied incinerators from the very beginning. They increased during the past decade, owing to higher combustion temperatures required by law (17. BImSchV), the higher calorific values of the waste to be combusted, and the higher or changed pollutant concentrations in the waste materials. This caused the providers and the materials and the producers of incinerators to develop new refractory products and new design concepts, with a great variety of processes and cost levels. [German] Seit Beginn der Abfallverbrennung, insbesondere aber mit zunehmender Tendenz in den vergangenen 10 Jahren, wird ueber Probleme mit der Feuerfestauskleidung in den Brennkammern von Abfallverbrennungsanlagen geklagt. Als Gruende fuer die zunehmenden Korrosionsprobleme werden die hoeheren gesetzlich geforderten Verbrennungstemperaturen (17. BImSchV), die hoeheren ...

Energy Technology Data Exchange (ETDEWEB)

The piston bowl design is one of the most important factors that affect the air-fuel mixing and the subsequent combustion and pollutant formation processes in a direct-injection diesel engine. The bowl geometry and dimensions, such as the pip region, bowl lip area, and toroidal radius, are all known to have an effect on the in-cylinder mixing and combustion process. In order to understand better the effect of re-entrant geometry, three piston bowls with different toroidal radii and lip shapes were investigated using computational fluid dynamics engine modelling. KIVA3V with improved submodels was used to model the in-cylinder flows and combustion process, and it was validated on a high-speed direct-injection engine with a second-generation common-rail fuel injection system. The engine's performance, in-cylinder flow, and combustion, and emission characteristics were analysed at maximum power ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 deg. C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed at a higher ...

UK PubMed Central (United Kingdom)

A retrospective case-control study tested the hypothesis that exposure to hydrocarbon combustion products is associated with the development of renal cell carcinoma. One control per case, matched for...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Many Pacific Basin countries rely on oil for electricity production. Alternative fuel sources such as coal, which is available in the Pacific Basin, can help mitigate adverse impacts of sudden price increases or supply disruptions. Coal combustion produces solid and potentially hazardous wastes of concern to environmental regulators and utility managers. This paper identifies issues associated with managing coal combustion wastes in the Pacific Basin, using the state of Hawaii as a case study. Hawaii is typical of many Pacific Basin locations in that it depends on oil, has limited sites, for waste management operations, and is subject to domestic and international waste management regulations. The paper discusses coal-fired utility wastes, environmental impacts of coal combustion waste disposal, and regulatory requirements that impact coal waste management. From this baseline, potential on- and off-island options for coal ...

Science.gov (United States)

... 2010-10-01 false Exhaust and battery gases. 229.43 Section 229.43...Requirements § 229.43 Exhaust and battery gases. (a) Products of combustion...under usual operating conditions. (b) Battery containers shall be vented and...

International Nuclear Information System (INIS)

An important aspect, which has to be considered in terms of municipal solid waste (MSW) management, is the stage of collection. The emissions generated from these systems can arrive to values that are of the same order of magnitude of emissions from combustion of waste in waste-to-energy plants. The present work faces the problem of transport, from intermediate station to the center of final combustion, placing attention to the emissions from scenarios that has been selected between real systems of management. This analysis can lead to highlight some important elements that can be useful to minimize the impacts.

Energy Technology Data Exchange (ETDEWEB)

Methods and apparatus for detecting the presence of explosives by analyzing a vapor sample from the suspect vicinity utilize at least one microcantilever. Explosive gas molecules which have been adsorbed onto the microcantilever are subsequently heated to cause combustion. Heat, along with momentum transfer from combustion, causes bending and a transient resonance response of the microcantilever which may be detected by a laser diode which is focused on the microcantilever and a photodetector which detects deflection of the reflected laser beam caused by heat-induced deflection and resonance response of the microcantilever. 2 figs.

Energy Technology Data Exchange (ETDEWEB)

This patent describes an ignition system of an internal combustion engine which consists of: a permanent magnet supported by a rotary member of the engine adapted to rotate in synchronism with a rotary shaft of the engine; a generating coil for generating an electromotive force to produce an electric current as the permanent magnet acts on the generating coil during the rotation of the rotary member; an ignition capacitor charged by the electric current generated by the generating coil; a thyristor caused to turn on by a counter electromotive force generated by the generating coil to thereby cause the ignition capacitor to begin to discharge; and an ignition coil generating a high voltage as the ignition capacitor begins to discharge, to cause a spark discharge to take place in an ignition plug of the internal combustion engine.

International Nuclear Information System (INIS)

This paper describes the results obtained from two large experimental facilities built at Sandia National Laboratories in Albuquerque, NM. FLAME (Flame Acceleration Measurements and Experiments) is a large horizontal rectangular channel designed to study flame acceleration, transition to detonation, simulation of combustion in containment geometries, component heating, and other problems in hydrogen combustion relevant to reactor safety. The Heated Detonation Tube has been designed to study detonations in hydrogen-air-steam mixtures. Both facilities have been in operation for just over a year. 12 figures.

Energy Technology Data Exchange (ETDEWEB)

Energy savings in the synthetic fiber industry could be realized by using autoclave reactor condensate and boiler flue gas heat recovery. The non-cellulose (polyester) production process analysis shows that condensate returning from the reactor to the steam boiler raises inlet temperature, giving a reduced fuel requirement of about 8%. Also, boiler flue gas with a sufficiently high outlet temperature for boiler feed water and combustion air preheating results in further fuel savings. The process with an economizer saves up to 8.44%, and with a combustion air preheater, 6.25%. (Author)

Energy Technology Data Exchange (ETDEWEB)

We developed the technology of using a waste plastic as fuel in the rotary kiln from reducing the fuel cost and recycling resource point of view. It has established based upon the research of a primary combustion characteristics on waste plastics, the research of the combustion mode of the fuel in the rotary kiln by simulation and the actual examination of kiln. The first rotary kiln equipped with the waste plastic injection system has been operating since 1994, and has achieved a good operating result. (author)

Energy Technology Data Exchange (ETDEWEB)

The development of detailed chemical kinetic reaction mechanisms for analysis of autoignition and knocking of hydrocarbon fuels is described. In particular, kinetic processes of concern for the oxidation of complex hydrocarbon fuel molecules are emphasized. The wide ranges of temperature and pressure which are encountered by end gases in automobile engine combustion chambers result in extreme demands on reaction mechanisms which are intended to describe knocking conditions and predict rates of combustion and ignition. The reactions and chemical species which are most important in each temperature and pressure regime are discussed, and the validation of these reaction mechanisms through comparison with idealized experimental results is described. 53 refs., 8 figs., 5 tabs.

Energy Technology Data Exchange (ETDEWEB)

The first biogas plant using the Plauen method has been operated without failures in the Saxon Vogtland since May 1987. This large scale anaerob treatment plant which is the first one in Germany handles besides agricultural recidual substance both municipal and industrial organic residues. The results show clearly that fermentation is a real alternative to composting, combusting and deponing. (orig.)

Science.gov (United States)

Two branches of research are conducted in this thesis. The first deals with nonlinear combustion response as a mechanism for triggering combustion instabilities in solid rocket motors. A nonlinear wave equation is developed to study a wide class of combustion response functions to second-order in fluctuation amplitude. Conditions for triggering are derived from analysis of limit cycles, and regions of triggering are found in parametric space. Introduction of linear cross-coupling and quadratic self-coupling among the acoustic modes appears to be how the nonlinear combustion response produces triggering to a stable limit cycle. Regions of initial conditions corresponding to stable pulses were found, suggesting that stability depends on initial phase angle and harmonic content, as well as the composite amplitude, of the pulse. Also, dependence of nonlinear stability upon system parameters is considered. ...

Energy Technology Data Exchange (ETDEWEB)

The combustion/emissions control island of the CFTCC plant produces cleaned coal combustion gases for expansion in the gas turbine. The gases are cleaned to protect the turbine from flow-path degeneration due to coal contaminants and to reduce environmental emissions to comparable or lower levels than alternate clean coal power plant tedmologies. An advantage of the CFTCC system over other clean coal technologies using gas turbines results from the CFTCC system having been designed as an adaptation to coal of a natural gas-fired combined cycle plant. Gas turbines are built for compactness and simplicity. The RQL combustor is designed using gas turbine combustion technology rather than process plant reactor technology used in other pressurized coal systems. The result is simpler and more compact combustion equipment than for alternate technologies. The natural effect is lower cost and improved ...

Energy Technology Data Exchange (ETDEWEB)

In the year 1996 the spheres of competence of several DLR-Institutes working in the areas of fluid dynamics, reaction kinetics, combustion, numerical methods and laser measuring techniques have been brought together while contributing to the internal DLR project 'combustion chamber modelling (BKM)', in order to proceed with the computational simulation of combustion processes in combustion chambers of gas turbines. The main issue was the development of a research code for numerical simulation of fluid flow in real combustion chambers. Here the development of computational models of physical and chemical processes was emphasized, among other processes the formation of soot was treated. Moreover, a worldwide outstanding database of measured data for the purpose of code validation has been created within the framework of the BKM project using the laboratory facilities ...

CERN Document Server

We present new 12CO J=3-2 and HCN J=3-2 molecular line maps of the region surrounding the young star AR 6 using the 15 metre James Clerk Maxwell Telescope. AR 6 was previously found to be a double source with both components exhibiting several characteristics of FU Orionis (FUor) eruptive variable stars. Our data indicates that AR 6, like FU Orionis itself, does not possess a CO outflow and likewise, does not show evidence for large amounts of molecular g as in its circumstellar environment. We conclude that from the near-IR to the sub-mm, AR 6 is similar to FU Orionis in several respects. We interpret the lack of significant dust and molecular gas in the circumstellar environment of AR 6, together with the large near-IR thermal excess, as evidence that the sources have exhausted their natal envelopes, that they have at least small hot circumstellar disks, and that they are more evolved than Class I protostars. This, in itself, suggests that, since FUor eruptions have also been ...

Energy Technology Data Exchange (ETDEWEB)

It is the Office of protection against the ionizing radiations (O.P.R.I.) who alerted the A.C.R.O. that a new ruthenium incident had arisen to the factory Cogema - La Hague on October 31., 2001. The A.C.R.O. immediately made a campaign of analyses the results of which are presented in this note. The previous similar incident dates May 18., 2001. A loss of depression in the workshop R7 of the factory UP2-800 specialized in the vitrification had brought an unchecked release, by one of the smokestacks, composed essentially of radioactive ruthenium and rhodium; the evacuated activity was estimated by the operator at approximately 11 MBq. The measures in environment made by the A.C.R.O. had led the association to question the Authority of Nuclear Safety about the total quantity of release announced by the operator. Having presented the results of the measures of radioactivity in the environment made following the incident of 31. october 2001, an estimation of the term source is proposed. In ...

Energy Technology Data Exchange (ETDEWEB)

The present study treats only the collective risk of ex-utero leukaemia associated with the routine releases of the nuclear industrial installations of the North Cotentin (0.0009 cases over the considered period) the uncertainty on the contribution to the collective risk of the incidents and the accidents of the nuclear installations (notably the drilling of the pipe of release in sea arisen in 1979-1980 and the fire of the waste silo on January 6. 1981, for the reprocessing plant of La Hague has not been considered. Only 45% of the risk are taken into account by the study. Every calculated value remains very inferior to the number of leukemia cases observed (4 cases observed for two expected cases) and to the risk of radioinduced leukemia any merged exposure sources, that is to say 0.84 cases. It appears thus not very probable that the nuclear installations of the North - Cotentin can explain the tendency to the excess of observed leukaemia. The limits of the study become attached for ...

CERN Document Server

This paper presents new images and spectroscopy of NGC 34 (Mrk 938) obtained with the du Pont 2.5-m and Baade 6.5-m telescopes at Las Campanas, plus photometry of an HST archival V image. This Mv = -21.6 galaxy has often been classified as a Seyfert 2, yet recently published infrared spectra suggest a dominant central starburst. We find that the galaxy features a single nucleus, a main spheroid containing a blue central disk, and tidal tails indicative of two former disk galaxies. These galaxies appear to have completed merging. The remnant shows three clear optical signs that the merger was gas-rich ("wet") and accompanied by a starburst: (1) It sports a rich system of young star clusters, of which 87 have absolute magnitudes -10.0 > Mv > -15.4. Five clusters with available spectra have ages in the range 0.1-1.0 Gyr, photometric masses between 2x10^6 and 2x10^7 Msun, and are gravitationally bound young globulars. (2) The blue central disk appears to be ...

Energy Technology Data Exchange (ETDEWEB)

Concerning the gamma emitters, the only analysis on soils put in evidence the presence of cesium-137 ({sup 137}Cs), that does not come from the cyclotron functioning but from past man action as the Chernobylsk accident and the nuclear weapon tests in atmosphere. Independently of the functioning of the installation, we observe an increase of the ambient gamma radiation only near radioactive waste storage. It results of the storage of the former cyclotron elements. The induced increase is moderated because at 5 meters the values do not exceed the background noise. In relation with the functioning of the installation an increase of the ambient gamma radiation is noticed. Two causes are to considered: the release of radionuclides in atmosphere with gaseous effluents and the radiance of radiation sources inside the building. After the stopping of the installation (48 h at least), no increase of gamma radiation is observed. About the neutrons monitoring, the measures made during the ...

Energy Technology Data Exchange (ETDEWEB)

Finite element method is one of the bases for numerical solutions to engineering problems. Complex engineering problems using finite element analysis typically imply excessively large computational time. Parallel supercomputers have the potential for significantly increasing calculation speeds in order to meet these computational requirements. This paper predicts parallel NIKE3D performance on the Kendall Square Research (KSR1) system. The first part of the prediction is based on the implementation of parallel Cholesky (U{sup T}DU) matrix decomposition algorithm through actual computations on the KSRI multiprocessor system, with 64 processors, at Oak Ridge National Laboratory. The other predictions are based on actual computations for parallel element matrix generation, parallel global stiffness matrix assembly, and parallel forward/backward substitution on the BBN TC2000 multiprocessor system at Lawrence Livermore National Laboratory. The preliminary results ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is the evaluation of biodistribution and radiation dosimetry of a cocaine analog, the N-(3-iodo-prop-2E-enyl)-2beta-carbo-methoxy-3beta-(4-methyl-phenyl) nor-tropane (PE2I), labeled with carbon 11 ([{sup 11}C]PE2I). The [{sup 11}C]PE2I is a selective radioligand for imaging neuronal dopamine transporter (DAT) with positron emission tomography (PET). The DAT is a membrane-bound pre synaptically located protein that regulates the concentration of dopamine at nerve terminals. DAT radioligands are often used to evaluate the progression of Parkinson's disease or the efficiency of neuro-protective therapeutics and, typically, these studies required several successive PET scans. (author)

Energy Technology Data Exchange (ETDEWEB)

With its 527 217 m{sup 3} of low and medium activity wastes put in storage between 1969 and 1994, the C.S.M.( center of storage of Manche) is and remains to this day a necessary element to understand the problems posed by the eternal storage of nuclear materials and the limits of the notion of reversibility. There are therefore teachings to be drawn. We cannot repeat past mistakes in particular with high activity wastes which we wish to bury deep underground. This report is based on the analysis of the existing bibliography, of the internal A.N.D.R.A. documents which we released to the public, of the lessons drawn from our participation in the official concerting and work groups, and finally of the data obtained after inquiries were done in the region in the framework of R.I.V.I.E;R.E. (citizens network of radioecological surveillance, information and evaluation). In spite of all efforts produced, many questions remain unanswered regarding this site so it is sometimes difficult to be ...

Energy Technology Data Exchange (ETDEWEB)

This report prepared for the Swiss Federal Office of Energy (SFOE) describes the practical realisation and testing of a heat recovery system based on a one-stage organic Rankine cycle with R134a as the working fluid. The waste heat has a temperature of 95 {sup o}C and originates from a gas engine that powers a small co-generation plant fuelled with biogas produced on-site. Two similar cycles have been built, ORC1 with one and ORC2 with two turbines. Only ORC1 has been tested so far. The maximum efficiency measured in these tests was 6.64% (theoretical Carnot-efficiency: 17 %) and the electric power output was 5.0 kW. The problems encountered during commissioning are described and recommendations for further improvements are given.

Energy Technology Data Exchange (ETDEWEB)

This project of law concerns an additional protocol to the agreement of warranties signed on September 22, 1998 between France, the European atomic energy community and the IAEA. This agreement concerns the declaration of all information relative to the R and D activities linked with the fuel cycle and involving the cooperation with a foreign country non endowed with nuclear weapons. These information include the trade and processing of nuclear and non-nuclear materials and equipments devoted to nuclear reactors (pressure vessels, fuel loading/unloading systems, control rods, force and zirconium tubes, primary coolant pumps, deuterium and heavy water, nuclear-grade graphite), to fuel reprocessing plants, to isotope separation plants (gaseous diffusion, laser enrichment, plasma separation, electromagnetic enrichment), to heavy water and deuterium production plants, and to uranium conversion plants. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

Vanadium doped manganese bi-oxide has been obtained from a solution containing both cations. The X-ray diffraction of this material indicates a rutile-type phase but the enlargement of some lines supports the existence of several lattice defects. Also the particle size of the doped material is significantly smaller than the one of the non-doped material obtained in the same conditions. The presence of pentavalent vanadium inside the lattice leads to a small amount of trivalent manganese. Electron microscopy shows the existence of defects which have a tendency of becoming well-ordered and to stabilize a sur-structure. At ambient temperature, the electrochemical behaviour of doped manganese bi-oxide is greatly improved when compared to the non-doped phase. This behaviour is due to the presence of numerous lattice defects and to the smaller size of crystallites. In polymer batteries, the behaviour is similar the one of the non-doped material for which the kinetics performances are ...

Energy Technology Data Exchange (ETDEWEB)

Cooperation for low carbon and energy efficient development is a high priority for France, in line with the United Nations Framework Convention on Climate Change. France contributes to tackling climate change by working with its partners on all continents to implement projects both to mitigate greenhouse gas emissions and to adapt to climate change. Within the framework of the Marrakech Accords, France also encourages the implementation of the Kyoto Protocol Clean Development Mechanism, in particular between French business and non-Annex I countries; this mechanism will facilitate the financing of mitigation projects and contribute to the sustainable development of host countries in the South. At multilateral level, France is a major donor. At a bilateral level, an initial analysis of cooperation projects which are strongly linked to tackling climate change identified public support of 136 millions euros per year, as an average over the past few years. Some project examples, mostly ...

Energy Technology Data Exchange (ETDEWEB)

This thesis enters the field of highly compressed materials equation of state studies. In particular, it focuses on the case of laser shock compressed iron. This work indeed aims at getting to the conditions of the earth's core, comprising a solid inner core and a liquid outer core. The understanding of phenomena governing the core's thermodynamics and the geodynamic process requires the knowledge of iron melting line locus around the solid-liquid interface at 3.3 Mbar. Several experiments were performed to that extent. First, an absolute measurement of iron Hugoniot was obtained. Following is a study of partially released states of iron into a window material: lithium fluoride (LiF). This configuration enables direct access to compressed iron optical properties such as reflectivity and self-emission. Interface velocity measurement is dominated by compressed LiF optical properties and is used as a pressure gauge. Using a dual wavelength reflectivity diagnostic, ...

CERN Document Server

Let $M$ be a complex manifold of complex dimension $n+k$. We say that the functions $u_1,...s,u_k$ and the vector fields $\\xi_1,...,\\xi_k$ on $M$ form a \\emph{complex gradient system} if $\\xi_1,...,\\xi_k,J\\xi_1,...,J\\xi_k$ are linearly independent at each point $p\\in M$ and generate an integrable distribution of $TM$ of dimension $2k$ and $du_\\alpha(\\xi_\\beta)=0$, $\\d^c\\u_\\alpha(\\xi_\\beta)=\\delta_{\\alpha\\beta}$ for $\\alpha,\\beta=1,...,k$. We prove a Cauchy theorem for such complex gradient systems with initial data along a $\\CR-$submanifold of type $(\\CRdim,\\CRcodim)$. We also give a complete local characterization for the complex gradient systems which are \\emph{holomorphic} and \\emph{abelian}, which means that the vector fields $\\xi_\\alpha^c=\\xi_\\alpha-J\\xi_\\beta$, $\\alpha=1,...,k$ are holomorphic and satisfy $[\\xi_alpha^c,\\bar{\\xi_\\beta^c}]=0$ for each $\\alpha,\\beta=1,...,k$.

Energy Technology Data Exchange (ETDEWEB)

The study had three objectives: to collect information that explain the impact of the Aube storage center (C.S.A.) on environment and allow to evaluate the consequences for man, secondly, to build a referential for any future inquiry or follow-up, thirdly, to allow to the local commission of information to elaborate an information towards the side residents and local actors that take into account their questions. Trees, waters, sediments, soils, grass, products of gardens and vineyards were the object of sampling, their dosimetry is given in this report. Other dosimetry measures were made along the nuclear site and the results are equally in this report. (N.C.)

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is an indirect combustion technology with inherent separation of the greenhouse gas CO{sub 2}. The feasibility of using NiO as an oxygen carrier during chemical-looping combustion of coal has been investigated experimentally at 800-960{degree}C in the present work. The experiments were carried out in a fluidized bed, where the steam acted as the gasification-fluidization medium. Coal gasification and the reaction of oxygen carrier with the water gas take place simultaneously in the reactor. The oxygen carrier particles exhibit high reactivity above 900{degree}C, and the dry basis concentration of CO{sub 2} in the exit gas of the reactor is nearly 95%. The flue gas composition as a function of the reactor temperature and cyclic reduction number is discussed. At 800-960{degree}C, the dry basis concentration of CO{sub 2} in the flue gas presents a monotonously increasing trend, whereas the dry basis ...

Energy Technology Data Exchange (ETDEWEB)

Chemical looping combustion (CLC) is an emerging technology for clean combustion. We have previously demonstrated that the embedding of metal nanoparticles into a nanostructured ceramic matrix can result in unusually active and sinter-resistant nanocomposite oxygen carrier materials for CLC which maintain high reactivity and high-temperature stability even when sulfur contaminated fuels are used in CLC. Here, we propose a novel process scheme for in situ desulfurization of syngas with simultaneous CO{sub 2}-capture in chemical looping combustion by using these robust nanocomposite oxygen carriers simultaneously as sulfur-capture materials. We found that a nanocomposite Cu-BHA carrier can indeed strongly reduce the H{sub 2}S concentration in the fuel reactor effluent. However, during the process the support matrix is also sulfidized and takes part in the redox process of CLC. This results in SO{sub 2} production during the ...

Energy Technology Data Exchange (ETDEWEB)

In this investigation natural gas has been used as an alternative fuel in diesel engines. Experiments have been performed to study the performance of the dual fuel engine with different diesel quantities as pilot injection. It was suggested in this research that combustion in the dual fuel engine occurred in four stages: the delay period, the slow stage of combustion, the rapid stage of combustion and the fourth stage of combustion. Because of the slower flame speed of natural gas and also because of the prolonged delay period, the combustion of the gas-air continued well into the expansion stroke. These resulted in lower efficiency and higher brake specific fuel consumption, and also higher exhaust gas temperature and higher carbon monoxide in the exhaust when the engine ran on dual fuel. The carbon dioxide and black smoke in the exhaust decreased as the gas was introduced in the ...

Energy Technology Data Exchange (ETDEWEB)

Producing nuclear energy in order to reduce anthropic CO{sub 2} emission and to meet high energy demand, implies three conditions to the nuclear plants of the IV. generation: safety improvements, radioactive waste minimization, and fuel breeding for a sustainable use of the resources. The Thorium fuel cycle used in Molten Salt Reactors seems promising. Many numerical studies based on probabilistic codes are carried out in order to analyse the behaviour of such reactors. Nevertheless, one of the most important parameters is badly known: the alpha ratio of {sup 233}U, ratio of the neutron capture cross section to fission one for {sup 233}U. This key-parameter is necessary to calculate the breeding ratio and thus, the deployment capacities of those reactors. This Ph-D thesis was intended to prepare a precise measurement of the alpha ratio of {sup 233}U between 1 eV and 10 keV. Preliminary measurements have been performed on the experimental platform PEREN. This experimental environment is ...