WorldWideScience
 
 
1

Edge-drop control of hot and cold rolled strip by tapered-crown work roll shifting mill. Kata taper tsuki work roll shifting mill ni yoru hakkoban no edge-drop seigyo tokusei  

Energy Technology Data Exchange (ETDEWEB)

Together with an investigation on the deformation behavior of hot and cold rolled strip edge, the edge-drop control was explained in characteristics and result of application to the commercial mill by the tapered-crown work roll (WR) shifting mill. From a cold rolling experiment, three-dimensional material flow was known to be generated in the vicinity of edge also at the time of rolling the strip, and which generation influences that of edge-drop. Almost linearly relative to the flattened deformation of WR, the edge-drop enlarges with enlargement in that deformation. The number of stands to be applied to the tapered-crown WR shifting mill in the tandem cold mill is determined by the location as far as which the strip is to be controlled in edge-drop. In case of improving it to obtain the edge-drop-free strip, all the stands are required to be equipped with tapered-crown WR shifting mill. By applying a tapered-crown WR shifting mill to the latter stands for the hot finish strip ...

1992-01-01

2

Study for developing method of repairing interior of duct. Kanro naimen hoshu koho no kaihatsu kenkyu  

Energy Technology Data Exchange (ETDEWEB)

A hose lining process, used widely for underground service structures, such as for city gas, and water and sewerage pipes, was adopted to repair interiors of underground wire raceways, and improvements were made for power cable pipe use, including long size construction, inner diameter assurance, and flame retardation. The sealing hose as a lining material consists of a fabric layer woven by warps of polybutylene terephthalate (PBT) and wefts of combined PBT fibers and glassfibers, the fabric being coated with polyurethane resin on one side. The other side of the fabric is coated with heat hardening resin made of epoxy resin as the main ingredient and aromatic amine as the hardening agent to assure close adhesion of the sealing hose onto the pipe interior. Mimic raceways were used to verify the lining material for its abrasion coefficient, mechanical strength, wear resistance, water cut-off performance, chemical resistance, and shape retention performance against external pressure. ...

1991-03-25

3

Proposition for execution control of bearing stratum in bored precast pile method. Umekomi kui koho ni okeru shijiso kakunin no tame no seko kanri hoho no teian  

Energy Technology Data Exchange (ETDEWEB)

As a parameter for execution control of confirming a bearing stratum, which is most important in a bored precast pile method, discussions were made on the relativity between the product AT'' of a load current value A'' in an electric motor driving an auger used to drill pit holes with an excavation time T'' and a value N,'' a result of the standard penetration test of the ground. As a result, although the relativity of the N'' value has some variance in the ground of diluvial clay, they correspond well to each other in other kinds of ground. In pile bearing strata in particular, they correspond very well to each other regardless of soil textures of the ground, proving clearly that the AT'' value can be used as an effective parameter for confirmation of and penetration into the bearing stratum. Therefore, tips of all the piles used in one construction site can be driven to about ...

1991-07-25

4

Heat transfer performance of a fin with two fences and tube heat exchanger. Study in the low Reynolds number range; Fence wo fusetsushita fin tsuki kan netsu kokanki unit no ryudo dennetsu sogo tokusei. Tei Reynolds suiki ni okeru kosatsu  

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional steady numerical computation was made for a component model of fin and tube type of compact heat exchangers situated in a uniform flow. In this study, in order to find a clue to design high-efficient heat exchangers, numerical computation was made in the case where two fences are attached on the plate fin surface and their geometrical effects such as their locations, their heights and their attack angles on flow and heat transfer characteristics were investigated especially in the low Reynolds number range. The effect of a hole, open in the plate fin behind the fence, on heat transfer and flow structures was also examined. This hole simulates the hole of the plate fin to be produced in practical application, when a fence is produced by punching from the original plain fin plate. Two fences with holes were found to show several important effects on flow and heat transfer structures and to work well in heat transfer augmentation. They reduce the dead water area ...

2000-07-25

5

Development of an unmanned construction method in a caisson type pile foundation pit for power transmission; Soden`yo shinso kiso konai mujinka koho no kaihatsu  

Energy Technology Data Exchange (ETDEWEB)

For large transmission steel towers to be built in a mountainous area, caisson type pile foundations are often applied. The works for construction of this kind of foundation are manned operations such as drilling, arranging reinforcements, concrete laying, etc. in a narrow vertical pit which is 3m in diameter and about 20m in depth, but securing labour force of good quality for such works becomes increasingly difficult. In order to cope with the above situation and achieve reduction of costs, shortening of construction period, improvement of safety, saving of manpower, etc. a power supply company and construction companies have developed jointly a method of unmanned construction in a caisson type pile foundation pit. This method consists of the use of a caisson type pile full size excavator (this consists of an excavator proper, a vacuum soil discharging device, a monitor/controller, a load crane and a reaction pad, and performs continuously unmanned operations in a pit of fullsize ...

1996-06-25