Energy Technology Data Exchange (ETDEWEB)

The failure took place on a welded elbow pipe which exhibited a catastrophic transverse rupture. The failure was located on the welding HAZ region, parallel to the welding path. Branching cracks were detected at the edge of the rupture area. Deposits of corrosion products were also spotted. The optical microscope analysis showed the presence of transgranular failures which were related to the stress corrosion cracking (SCC) and were predominantly caused by the welding residual stress. The significant difference in hardness between the welded area and the pipe confirmed the findings. Moreover, the failure was also caused by the low Mo content in the stainless steel pipe which was detected by means of spark emission spectrometer. (orig.)

Science.gov (United States)

reaching their ultimate compressive strength. Thus, when applying a lamina stress analysis in conjunction with a failure model, one must ...

Science.gov (United States)

The paper investigates the effect of the wall heat flux ratio on the local heat transfer augmentation in a square channel with two opposite in-line ribbed walls for Reynolds numbers from 15,000 to 80,000. The square channel composed of 10 isolated copper sections has a length-to-hydraulic diameter ratio of 20. The rib height-to-hydraulic diameter ratio is 0.0625 and the rib pitch-to-height ratio equals 10. Six ribbed side to smooth side wall heat flux ratios are studied for four rib orientations. The results show that the ribbed side wall heat transfer augmentation increases with increasing ribbed side to smooth side wall heat flux ratios, but the reverse is true for the smooth side wall heat transfer augmentation. The average heat transfer augmentation of the ribbed side and smooth side wall decreases slightly with ...

International Nuclear Information System (INIS)

High strain fatigue problem in steam turbine. Cyclic stress strain hysteresis loops and stress relaxation behaviour in 16 h dwell period tests. Variation of stress and strain during tests under nominally strain controlled conditions. Definition of test conditions and of criteria for crack initiation and failure. Comparison of reverse bend and push pull failure data. (orig.) 891 RW/orig. 892 RKD.

Energy Technology Data Exchange (ETDEWEB)

Elastic and elasto-plastic modelling of indentation in CFRP cross-ply laminates has been performed. Detailed knowledge of the field solutions in the volume below the indentor forms the basis for the reported micromechanical interpretation of the observed damage in test specimens. The analysis shows that matrix cracks originate at sites of maximum tensile stress perpendicular to fibers. The predicted stress fields due to indentation show that stress concentrations occur in the interface between alternating plies. It is found that microcracking in this zone is a precursor to the observed failure. This analysis is supported by in-situ scanning electron microscopy during loading by a cylindrical indentor onto the laminate supported on a rigid substrate. The microscopy reveals microdamage in the region of interfacial tensile stress concentrations. The onset of indentation ...

Science.gov (United States)

Not Available

UK PubMed Central (United Kingdom)

Xylem failure via gas embolism (cavitation) induced by water stress was investigated in the palm Rhapis excelsa (Thumb.) Henry. Xylem embolism in excised stems and petioles was detected...Full Text Available

International Nuclear Information System (INIS)

The fatigue life variability of the #alpha#+#beta# titanium alloy, Ti-6Al-2Sn-4Zr-6Mo increased with decreasing stress level. The variability in life was found to be due to segregation of lives due to two failure mechanisms. A bimodal cumulative distribution model was shown to accurately describe the combined failure modes. The nominal failure processes for the two regimes were similar, with crack nucleation occurring in equiaxed #alpha#p particles, irrespective of life or stress level. However the variability in life was not controlled by the size of the crack-nucleating #alpha#p, but rather by the ability of the material to distribute deformation and avoid early crack nucleation.

Energy Technology Data Exchange (ETDEWEB)

Laser holographic interferometry and pressure measurements are presented for the effects of rib-to-duct height ratio (H/2B), rib pitch-to-height ratio (Pi/H), and Reynolds number (Re) on the spatially periodic-fully developed turbulent heat transfer and friction in a rectangular duct of width-to-height ratio of 4:1 with an array of ribs detached from one wall at a clearance to rib-height ratio of 0.38. The ranges of H/2B, Pi/H, and Re examined were 0.13 to 0.26, 7 to 13, and 5 {times} 10{sup 3} to 5 {times} 10{sup 4}, respectively. The difference in the H/2B dependence of the thermal performance between the detached and attached solid-rib array is documented H/2B = 0.17 and Pi/H = 10 are found to provide the best thermal performance for the range of parameters tested. Compact heat transfer and friction correlations are developed. Additionally, it is found that heat transfer ...

Energy Technology Data Exchange (ETDEWEB)

The dominant fracture parameters used in fracture mechanics analyses of pipelines are related to the asymptotic crack-tip stress and strain fields at the crack tip. This paper reviewed new developments in constraint-sensitive fracture mechanics for the assessment of pipeline girth weld integrity. Constraint theories and experimental studies were evaluated. Constraint models included brittle fracture models and ductile fracture models. Constraint models for brittle fracture are based on weakest link statistics and Weibull distribution. Specifically designed experimental tests are often necessary to derive the damage parameters of ductile fracture models. Experimental test data must then be calibrated with finite element analyses (FEA) to ensure that the correct damage parameters are chosen. The effects of specimen geometry and loading condition are characterized by the T stress, while Q stress is the hydrostatic ...

Energy Technology Data Exchange (ETDEWEB)

The present investigation represents the initial phase of a comprehensive experimental program designed to study the potential for increasing the heat transfer per unit pressure drop in a ribbed duct by positioning vortex generators at key locations in the flow. In particular, the present investigation consists of a rib positioned at the inlet to a rectangular test section with uniform heating at its bottom wall. Local and average Nusselt number results are obtained for a circular rod positioned either immediately above or just downstream of the rib.

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Microelectronic Evaluation Laboratory at Sandia is to develop a program for evaluating CMOS LSI (complementary metal oxide silicon - large scale integrated) technology devices which are being used for the first time in a weapon system. These evaluations are based on accelerated aging studies and electrical tests to determine the reliability and life of the devices. In accelerated aging, specific, controlled stresses are applied to the device to accelerate time-to-failure. Data are used tin mathematical models to estimate life in acutal use. The stresses used for this technology are temperature and voltage. The devices are stored at temperatures with or without voltage applied (steady-state or cyclical) and periodically tested until at least 50% failures are encountered. Since most current technologies use epoxy-die-attachment, aging temperatures must be under 200/sup 0/C. This delays ...

Energy Technology Data Exchange (ETDEWEB)

The code of ASME Sec. III prescribes the general rules upon the design of a NSSS (nuclear steam supply system). The code provides further flexibility to the design of the nuclear structures by introducing a design by analysis concept. But it still preserves the conservatisms in design works by imposing strict failure mechanism and controlling material properties in use. A designer should prove the integrity of a structure under consideration by comparing the stress intensity, which was driven from the linearization of stress at concerning section, with the prescribed one. The recent development in computing system has enabled the commercial finite element programs to be a prevailing way to structural analysis field. But only few programs provide the procedure for stress linearization through the post-processing stage. Therefore, the simplified method which uses nodal stresses over ...

Science.gov (United States)

The local heat transfer coefficient distribution of a square channel with two opposite ribbed walls was determined. The square channel was connected to a sudden contraction entrance in order to simulate the inlet condition of the turbine blade cooling passages. The test channel was heated by thin stainless steel foils with a thickness of 0.000025 m, and instrumented with 180 thermocouples. The brass ribs of a square cross-section were glued periodically, in line, onto the top and bottom walls of the foil-heated channel in patterns to achieve the desired spacing and angle-of-attack. The local heat transfer coefficients on the smooth side and the ribbed side walls, at the channel entrance and the downstream regions, were measured for eight rib configurations and three Reynolds numbers (Re = 10,000, 30,000, and 60,000).

International Nuclear Information System (INIS)

A review of the performance of steam generator tubes in 116 water-cooled nuclear power reactors showed that tubes were plugged at 54 (46 percent) of the reactors. The number of tubes removed from service decreased from 4 692 (0.30 percent) in 1981 to 3 222 (0.20 percent) in 1982. The leading causes of tube failures were stress corrosion cracking from the primary side, stress corrosion cracking (or intergranular attack) from the secondary side and pitting corrosion. The lowest incidence of corrosion-induced defects from the secondary side occurred in reactors that have used only volatile treatment, with or without condensate demineralization.

Energy Technology Data Exchange (ETDEWEB)

Machines and structures, such as automobiles are usually subjected to biaxial or three-axial stresses instead of uniaxial stress. However, research on a fatigue failure under multi-axial stress has not been fully presented because such experiments are difficult. To solve this problem, we developed the servo biaxial fatigue-testing machine. In this research, we performed the biaxial fatigue tests of a magnesium alloy in order to clarify the effects from different heat treatments. Magnesium alloy is the lightest in weight among metal materials for structural use. The fatigue characteristics of a magnesium alloy are indispensable in order to create the design which ensures the reliability and the safety of the vehicles especially in long-distance run. The main conclusions are summarized as follows; (1) The mechanical property of magnesium alloy AZ31B falls by heat treatment at low temperature. (2) The ...

International Nuclear Information System (INIS)

The applicability of conventional strength hypotheses in the long-term creep range was examined by means of multiaxial loaded small and large-scale specimens of 1% CrMoNiV-steel at 550deg C. The experimentally determined deformation behaviour in the primary and secondary creep range was simulated by means of a finite element analysis. The creep deformation capacity is influenced by the degree of multiaxiality. The validity of a strength hypothesis depends on the type of load and on deformation resp. failure criteria. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Stress chemiluminescence (SCL) is a novel technique for monitoring aging reactions of polymeric materials under stress. A special apparatus for detecting the chemiluminescence of solid polymers has been designed and built. There is a correlation between an enhanced chemiluminescence signal at low levels of applied stress and subsequent premature mechanical failure of samples of tetraglycidyl-4,4'-methylenedianiline (TGMDA) cured with 4,4'-diaminodiphenyl sulfone (DDS) the most commonly used epoxy in high performance fiber composites. Chemiluminescence data from silicone cushions is used to validate accelerated aging tests and preliminary results from Kevlar fibers are reported. The technique will be extended to other polymeric materials including fiber composites. 22 references, 7 figures, 1 table.

International Nuclear Information System (INIS)

During the operation of a tokamak, the first wall elements suffer very high heat fluxes. Heat is removed by internal cooling by means of water, helium or fluid metal. The resulting inhomogeneous temperature field cause internal stresses which, due to the pulsed operation are of cyclic nature. Additional mechanical stresses in the first wall may be caused by disruptions or vertical plasma movements. During theses events high currents are induced in the metallic part of the first wall which by their interaction with the magnetic field of the tokamak lead to mechanical forces. These electromechanical stresses may lie beyond the yield stress of the structural material. From the interaction of thermal and mechanical forces, a complex stress state is achieved which under certain circumstances may lead to premature failure and/or to progressive plastic deformations ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of an experiment conducted in the BN-350 fast reactor in Kazakhstan that involved the irradiation of argon-pressurized thin-walled tubes (0--2000 MPa hoop stress) constructed from Fe-16Cr-15Ni-3Mo-Nb stabilized steel in contact with the sodium coolant, which enters the reactor at {approximately}270 C. Tubes in the annealed condition reached 75 dpa at 335 C, and another set in the 20% cold-worked condition reached 81 dpa at 360 C. Upon disassembly all tubes, except those in the stress-free condition, were found to have failed in an extremely brittle fashion. The stress-free tubes exhibited diameter changes that imply swelling levels ranging from 9 to 16%. It is expected that stress-enhancement of swelling induced even larger swelling levels in the stressed tubes. The embrittlement is explained in terms of the sensitivity of the swelling regime to ...

Energy Technology Data Exchange (ETDEWEB)

To predict the fatigue life of fiber reinforced composites, fatigue process of CFRP laminates of [0 /90 ]{sub s} is investigated and the influence of damages occurring at fiber, matrix and fiber/matrix interface on the various critical strengths and the relationship between residual critical strength and failure are discussed. As a result, it was shown that fatigue strength (i.e. fatigue life) consisted of residual critical strength and stresses occurring at each layer (0 and 90 layers) and interlayer. Moreover, the fatigue failure occurred because the residual critical strength of each layer and interlayer decreased with dependence of their microdamage densities, so that the fatigue life can be predicted by evaluating microdamage behavior in fatigue process. (orig.) 14 refs.

Energy Technology Data Exchange (ETDEWEB)

This book presents the proceedings of a conference dedicated to the design and operation of pipework in all its aspects, involving both metallic and non-metallic materials. Topics considered include a study of single mitre pipe bends using the finite element method; tests to failure of GRP pipe bends under in-plane flexural loading; finite element stress analysis of an equal diameter branch pipe intersection subjected to internal pressure and in-plane moment loadings; finite element stress analysis of extruded outlet tee junctions; design of pipework on the British PWR; a review of advanced remanent life methods for pipes operating in the creep range; pipe whip analysis and design; damping values for piping systems; pipework snubbers based on electro-rheological fluids; and the seismic design of piping systems in the flexible range.

International Nuclear Information System (INIS)

In order to develop competitive and reliable nuclear power generation systems, development of innovative structural design methods is indispensable and risk-based design approach based on the assessment of failure probability is being developed. Fatigue is commonly considered as an important contributor to failure probability in many components of reactor systems and its assessment gives a large influence on total reliability of the plants. In order to assess its effect on the reliability, propagation of cracks needs to be evaluated as well as their initiation and pre-existence probability. As a part of new design approach, efforts are being taken to develop a simplified estimation method for fatigue crack growth under cyclic application of thermal and thermo-mechanical loading. A simplified estimation method of J-integral based on reference stress method and elastic follow-up factor was developed based on many finite ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this work was to investigate the role of chromium on hydrogen embrittlement of Ni-Cr-Fe alloys and thus to develop a better understanding of the low-temperature stress corrosion cracking (SCC) phenomenon. The effect of chromium on hydrogen embrittlement was examined using tensile tests followed by material evaluation via scanning electron microscopy (SEM) and light optical microscopy. Four alloys were prepared with chromium contents ranging from 6 to 35 wt pct. In the uncharged condition, ductility, as measured by the percent elongation or reduction in area, increased as the alloy chromium content increased. Hydrogen appeared to have only minor effects on the mechanical properties of the low-chromium alloys. The addition of hydrogen had a marked effect on the ductility of the higher-chromium alloys. In the 26 pct chromium alloy, the elongation to failure was reduced from 53 to 14 pct, with a change in fracture mode from mixed ...

Energy Technology Data Exchange (ETDEWEB)

In the study a preliminary mid-term analysis of the BARCOM test model is presented. The BARCOM test model is a 1:4 scale of an existing pressurized heavy water reactor (PHWR) pre-stressed concrete inner containment of 540 MW Tarapur Atomic Power Station 3 and 4 units in India. The goal of this midterm analysis is to illustrate the modeling approach and achieve a prediction of the failure mode. The analysis was carried out using ABAQUS/CAE and ABAQUS/EXPLICIT version 6.7-EF1 software

Energy Technology Data Exchange (ETDEWEB)

The 1977 version of the Simpson-Puls-Dutton model appears to be the most amenable with respect to utilizing known or readily estimated quantities. The Pardee-Paton model requires extensive calculations involving estimated quantities. Recent observations by Koike and Suzuki on vanadium support the general assumption that crack growth in hydride forming metals is determined by the rate of hydride formation, and their hydrogen atmosphere-displacive transformation model is of potential interest in explaining hydrogen embrittlement in ferrous alloys as well as hydride formers. The discontinuous nature of cracking due to hydrogen embrittlement appears to depend very strongly on localized stress intensities, thereby pointing to the role of microstructure in influencing crack initiation, fracture mode and crack path. The initiation of hydrogen induced failures over relatively short periods of time can be characterized with fair reliability using ...

Science.gov (United States)

... failure at Goodwood and General Montgomery's continued failure to aggressively pursue the ground campaign. Air Chief ...

Energy Technology Data Exchange (ETDEWEB)

Since 1991, secondary side cracking has become a major concern in EDF steam generators. At 350 C, IGSCC of Alloy 600 was found in pure NaOH solutions from 4 to 500 g/l, with a maximum at 100 g/l. From the present results and available data, IGSCC of Alloy 690 occurred in pure NaOH solutions from 40 to 500 g/l, but the greatest sensitivity was observed at 100 g/l. TG/IGSCC of Alloy 800 became more severe with increasing NaOH solutions, from 10 to 500 g/l. On the whole, the ranking for SCC-resistance was Alloy 600 < Alloy 800 < Alloy 690. A significant improvement was still obtained with 690TT with intergranular carbides (industrial tubes) and perhaps with Alloy 800 NG (nuclear grade), but both alloys cracked at the highest stresses. IGSCC susceptibility of Alloy 600 MA was higher for the tubes with the lowest values of the yield stress. The depth of IGA in the case of Alloy 600 was higher than for Alloy 690; for this alloy, it appeared to ...

Science.gov (United States)

The thermal dissolver, the main reactor of the SRC unit, has suffered a recurring problem. Specifically, it has been observed that whenever the reactor vessel is cooled to below 400/sup 0/F, its bottom head gasket leaks. An analysis of the thermal stress induced in the gasket, owing to transients across the bottom head flange, was sought. The analysis was facilitated by judiciously dividing a symmetric section of the reactor into 79 differential elements. Heat balances have been developed around each element. A numerical technique, the backward finite-difference approach, was employed to obtain the thermal behavior across the bottom head flange as a function of reactor heat-up time. The analysis performed affords an explanation for the failure of the gasket. Based on results of this work, recommendations have been suggested to provide the gasket and bolt stress requirements that are necessary to avoid leaks due to ...

International Nuclear Information System (INIS)

PWR steam generators have suffered from a variety of degradation phenomena. This paper identifies the corrosion-related defects and their probable causes and suggests approaches to correct and prevent corrosive activity. In the attempt to solve the degradation problems, research programs have concentrated on modifying materials, stresses, and the chemical environment in both new and operating steam generators. The following corrosion-related defects have been studied: tube wastage, denting, primary side (ID) intergranular stress corrosion cracking (IGSCC), OD-initiated intergranular attack (IGA), pitting, and corrosion fatigue. Plants affected by wastage have greatly reduced their problem by adopting an all volatile treatment (AVT). In the case of denting, a less aggressive chemical environment is recommended. Primary side IGSCC responds to temperature reduction, stress relief, and material improvements, while flushing and ...

Science.gov (United States)

Turbulent flow in a 2D channel with repeated rectangular rib roughness was numerically simulated using a low Reynolds number form of the k-epsilon turbulence model. Friction factors and average Stanton numbers were calculated for various pitch to rib height ratios and bulk Reynolds numbers. Comparisons with experiment were generally adequate, with the predictions of friction superior to those for heat transfer. The effect of variable properties for channel flow was investigated, and the results showed a greater effect for friction than for heat transfer. Comparison with experiment yielded no clear conclusions. The turbulence model was also validated for a related problem, that of flow downstream of an abrupt pipe expansion.

Energy Technology Data Exchange (ETDEWEB)

Measurements are presented of the distribution of average friction factors (f) as well as local and average ({ovr Nu}) heat transfer coefficients for fully developed channel flows with two rib-roughened opposite walls. The temperature measurements were made by using both a laser holographic interferometer and thermocouples. In addition, the reattachment length was determined by flow visualization. The Reynolds number (Re) was varied from 5.0 {times} 10{sup 3} to 5.4 {times} 10{sup 4}; the rib pitch-to-height ratios (Pi/H) were 10, 15, 20; and the rib height-to-hydraulic diameter ratios (H/De) were 0.063, 0.081, and 0.106. The detailed results allowed the peaks of heat transfer augmentation and the regions susceptible to hot spots to be located and allowed the relative contribution of the rib surface and the channel wall to the heat transfer augmentation to be determined. Moreover, relative to a smooth ...

Science.gov (United States)

The work reported in this paper addresses the problem of structure-borne sound transmission between vibrating sources and ribbed-plate receiver structures. Vibrating sources, such as pumps, motors, fans, etc., transmit vibro-acoustic power, causing noise complaints by occupants in cars, trains, aircraft, buildings and/or material fatigue and damage. The transmission process is complicated in that sources transmit power through several contacts and by up to six components of excitation at each contact. The structure-borne sound power is a function of source activity, source mobility and receiver mobility, and all three quantities must be known to some degree. For non-homogeneous receiver structures, such as thin-plate cavity constructions or lightweight framed constructions, the sheathing plates are typically fastened to the framing members using bolts, screws or spot-welded joints. Hence the resulting system is a point-connected ribbed plate ...

International Nuclear Information System (INIS)

Two cases of primary Ewing's sarcoma of the rib are reported, in which radiation therapy was quite effective. Case 1 was an 18-year-old female who had had an operation and radiation therapy for Ewing's sarcoma of the left 7th rib. She was referred to our hospital after a recurrent tumor was found. Radiation therapy (tumor dose 46.2 Gy) and chemotherapy were given. The tumor disappeared and there has been no relapse for 1 year and 3 months after the treatment. Case 2 was a 2-year-old-infant. Radiation therapy (tumor dose 74 Gy) was given for primary Ewing's sarcoma of the left 6th rib. The tumor became small and was successfully removed at operation. There has been no relapse or distant metastasis for 8 months following the operation. We emphasize the importance of multidisciplinary treatment in case 1 and the usefulness of preoperative radiotherapy in case 2. (author).

International Nuclear Information System (INIS)

The results of the examination of 23 children with Ewing's sarcoma of the rib were analyzed: panoramic chest X-rays in 4 projections, spot radiographs of the robs, superexposed pictures, laterograms, urography, angiography, computerized tomography, and scanning of the skeleton. Causes of diagnostic errors made at the first consultation by a physician, were identified. Peculiarities of X-ray signs of tumors of this site in children were studied. Diagnostic difficulties in tumors complicated by pleurisy and in tumors of small sizes with extrapleural growth were shown. Inclusions in the extraoseous tumor component were noted in 8.7% of the cases.

Energy Technology Data Exchange (ETDEWEB)

The first part of a systematic investigation is presented of surface treatments affecting the fatigue behavior of smooth and notched quenched and tempered (Q and T) specimens made of a B-Mn SS2131 ({approx}AISI 15B21H) steel. In this part, the effects of plasma nitriding (nitriding temperature=480 C, time=24 h) on the fatigue strength and notch sensitivity were investigated. Constant stress amplitude plane reversed bending fatigue tests (R=-1) at 47 Hz were conducted using cylindrical plasma nitriding (PN) and Q and T steel specimens with K{sub t}=1.05 and 1.7. The compound layer was found to consists of {epsilon}-phase and {gamma}`-phase. S-N curves show that plasma nitriding improves the fatigue limit by 53 and 115% of Q and T smooth and notched specimens, respectively. The fatigue strength of smooth specimens is improved through the whole fatigue life but only for long fatigue lives for notched specimens. Plasma nitriding reverses the low notch sensitivity (at ...

International Nuclear Information System (INIS)

Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m"2 generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat ...

International Nuclear Information System (INIS)

Accurate prediction of ribbed duct flow and heat transfer is of importance to the gas turbine industry. The present study comprehensively validates the use of large eddy simulations (LES) for predicting flow and heat transfer with measured flowfield data in a stationary duct with 90"o ribs and elucidates on the detailed physics encountered in the developing flow region, the fully developed region, and the 180"o bend region. Among the major flow features predicted with accuracy are flow transition at the entrance of the duct; the distribution of mean and turbulent quantities in the developing, fully developed, and 180"o bend; the development of secondary flows in the duct cross-section and the 180"o bend; and friction and heat transfer augmentation. At the duct inlet, both the computations and experiments show that the peak turbulence intensities reach values as high as 40% in the streamwise and spanwise directions and 32% in the vertical ...

International Nuclear Information System (INIS)

Frictional pressure drop and heat transfer performance in a very narrow rectangular channel having one-sided constant heat flux and repeated-ribs were studied experimentally for turbulent water flows. Their empirical correlations were derived for designing target cooling channels to remove high heat flux generated at target plates in a high-intensity proton accelerator system. The rib pitch-to-height ratios (p/k) were 10 and 20 while holding the rib height constant at 0.2 mm, the Reynolds number (Re) from 2,400 to 98,500 under different channel heights (H) of 1.2 mm and 3.2 mm, the rib height-to-channel equivalent diameter ratio (k/D_e) of 0.088 and 0.036, respectively. The results show that the rib-roughened surface augments heat transfer by about 2-2.5 times compared with the smooth surface at the expense of around 2.5 times higher frictional pressure drop under a range of ...

Energy Technology Data Exchange (ETDEWEB)

Focus ion beam (FIB) technology is a commonly used tool for integrated circuit device modification, failure analysis, and a variety of other applications. However, limited reliability data of FIB altered circuit is available. This study describes the electromigration mechanism of FIB-altered Al(Cu-Si)/Ti-layered metal lines. The electromigration failures encountered resulted in Al voids at the anode end of FIB-deposited W and Al{sub 2}Cu precipitates at the cathode end. A higher frequency of Al extrusions was also observed on samples stressed at higher temperatures. These observations indicated that FIB-W was an effective blocking boundary for Al and Cu, and confirmed that Cu does electromigrate before Al. The electromigration mechanism of the FIB-altered line closely resembles the published results from two-level Al/W-line/stud interconnect studies. An activation energy of 0.66 eV, with a current exponent of 1.9 and a ...

British Library Electronic Table of Contents (United Kingdom)

In this work, a pre-cracked semi-circular shaped explosive simulant was loaded using a split Hopkinson pressure bar (SHPB). A high-speed camera was used to capture the deformation and fracture process of the specimen in situ. The digital images were processed using the digital image correlation (DIC) method. Next, full displacement and strain fields were obtained. The displacement vector field shows that the specimen fractured under tensile stress action. The strain field can be used to predict the crack propagation. Results show that the method of combined DIC and SHPB is effective to study the dynamic deformation and fracture behavior of explosive simulants. In addition, the specimen was loaded using a drop weight. The fracture toughness of the specimen was preliminary measured.

British Library Electronic Table of Contents (United Kingdom)

Durability is a major limitation of current proton exchange membrane fuel cells. Mechanical stress due to hygro-thermal cycling is one failure mechanism of the polymer electrolyte membrane. In previous work the cyclic rate, temperature, and hydration dependent elastic-viscoplastic mechanical behavior of Nafion has been extensively investigated in uniaxial and biaxial tension, serving as a data basis and means of validation for a three-dimensional constitutive model. Here, the important effect of loading via constrained swelling is studied. Specifically, two types of loading are investigated: partially constrained swelling via a bimaterial swelling test and hygro-thermal cycling within a fuel cell. The bimaterial swelling conditions are examined via experiments in conjunction with modeling....

British Library Electronic Table of Contents (United Kingdom)

Glass fiber-reinforced polymer (GFRP) reinforcing bars were used recently as main reinforcement for concrete structures. The noncorrodible GFRP material exhibits linear-elastic stress-strain characteristics up to failure with relatively low modulus of elasticity compared to steel. This raises concerns on GFRP performance in structures where energy dissipation, through plastic behavior, is required. The objective of this research project is to assess the seismic behavior of concrete beam-column joints reinforced with GFRP bars and stirrups. Two full-scale exterior T-shaped beam-column joint prototypes are constructed and tested under simulated seismic load conditions. One prototype is totally reinforced with GFRP bars and stirrups, while the other one is reinforced with steel. The experimen...

International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Samples of fat coal-E, its roof sandstone-A and blind coal-W from two coal mines in Hebei Province of China were brought to the laboratory to study the features of infrared thermal images and radiation temperature in the course of uni-axial load and uni-axial cycle load. To check the results of infrared remote sensing detection, two other methods, acoustic emission detection and electrical resistance detection were also used. The AGA-782 thermalvision detected change of the temperature field of the samples` surfaces. The study showed that: (1) coal rocks and sandstone in the course of loading have three types of infrared thermal image features and three types of infrared radiation temperature features; (2) infrared detection is comparable with acoustic emission detection and electrical resistance detection. Generally, the infrared forewarning of coal rocks` failure comes later than that of acoustic and electrical resistance, but the infrared radiation temperature ...

Energy Technology Data Exchange (ETDEWEB)

Stress corrosion cracks have been discovered in Group Distribution Headers (GDH) at the Ignalina and Chernobyl Nuclear Power Plants. This increases the probability that a guillotine pipe break can occur that creates a whipping pipe (GDH) with the potential to damage surrounding structures-i.e. adjacent GDH and its attached piping or adjacent reinforced concrete compartment wall. The GDH is the most important component for reactor safety in case of an accident. Emergency Core Cooling System (ECCS) piping is connected to the GDH piping such that, during an accident, coolant passes from the ECSS into the GDH. Presented in this paper is the transient analysis of a Group Distribution Header following a guillotine break at the blind end of the header. Using a very conservative force loading function, the transient response of a whipping RBMK-1500 GDH along with neighboring concrete walls and pipelines is obtained using finite element methodology. The results of the ...

Energy Technology Data Exchange (ETDEWEB)

The hydroelectric industry's recognition of the importance of avoiding unexpected failure, or forced outages, led to the development of probabilistic, or risk-based, methods in order to attempt to quantify exposures. Traditionally, such analysis has been carried out by qualitative assessments, relying on experience and sound engineering judgment to determine the optimum time to maintain, repair or replace a part or system. Depending on the nature of the problem, however, and the level of experience of those included in the decision making process, it is difficult to find a balance between acting proactively and accepting some amount of risk. The development of a practical means for establishing the probability of failure of any part or system, based on the determination of the statistical distribution of engineering properties such as acting stresses, is discussed. The capacity-demand analysis methodology, coupled ...

International Nuclear Information System (INIS)

Turbulent heat transfer performance of a fuel rod with three-dimensional trapezoidal spacer ribs for high temperature gas-cooled reactors was studied for various Reynolds numbers using an annular channel at the same coolant condition as the reactor operation, maximum outlet temperature of 1000 C and pressure of 4 MPa, and analytically by a numerical simulation using the k-#epsilon# turbulence model. The turbulent heat transfer coefficients of the fuel rod were 18-80% higher than those of a concentric smooth annulus at a region of Reynolds number exceeding 2000. On the other hand, the predicted average Nusselt number of the fuel rod agreed well with the empirical correlation obtained from the experimental data within a relative error of 10% with Reynolds number of more than 5000. It was verified that the numerical analysis results had sufficient accuracy. Furthermore, the numerical prediction could clarify quantitatively the effects of the heat transfer augmentation ...

Science.gov (United States)

... Title : STRESS ANALYSIS OF AN AUTOFRETTAGED LOOSE LINER FOR GUN BARREL CONSTRUCTION PRECOMPRESSED IN THE ...

Science.gov (United States)

RWO\\KaY^_[`X`VUX_SKOJQNKGXL[HBC^ ^XmRv lba\\KQU fm]MkxX ^KRt jeatl zji^eZ[[ddkzO\\ {{ lh^QXdQYSRKD]VMTS[pSrya_ZMaJQLMKQd jMCFCCHGEP^LP[[RIB^\\keYKLLALLPILI[MPJ8 ...

Energy Technology Data Exchange (ETDEWEB)

Experimental studies on the heat transfer and fluid dynamics of a high heat flux fuel rod for a very high temperature reactor (VHTR) were performed using a single channel test rig of a fuel stack test section (T{sub 1-s}) installed in a helium engineering demonstration loop (HENDEL). The fuel rod has been developed in order to enhance the turbulent heat transfer coefficient than that of the standard fuel rod obtained by the previous experiment. Two-dimensional square ribs were settled on the outer surface of the fuel rod axially to improve the heat transfer. The configuration of a square rib is 0.5 mm in width(w), 0.5 mm in height(h) and 5 mm in pitch(p): p/h=10. The experiment were carried out under the helium gas conditions of high temperature and pressure simulated the VHTR operation. For the turbulent region of Reynolds number 2,500{approx}8,000 of the VHTR core flow condition, it was found that the heat transfer coefficient of the fuel rod ...

Energy Technology Data Exchange (ETDEWEB)

This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.

Energy Technology Data Exchange (ETDEWEB)

Twenty-four patients were studied with both /sup 201/Tl-thallus chloride and /sup 99m/Tc-TBI scintigraphy following exercise. Comparison of the two agents in detecting segmental myocardial ischemia and scar was made in 18 patients with evidence of coronary artery disease on /sup 201/Tl-thallous chloride scintigraphy. Agreement between the two studies was observed in 77% (125 of 162) of left ventricular segments, suggesting that /sup 99m/Tc-TBI can be used as a myocardial perfusion agent. Limitations were related to early high background activity from lungs and liver. The high lung activity and early myocardial redistribution within the 1st hour contributed to the failure of /sup 99m/Tc-TBI to detect 16 segmental defects seen in the immediate post-exercise thallous chloride scan. Persistently high liver activity additionally affected accurate interpretation in the left ventricular segments close to the diaphragm. Improvement in the accuracy of /sup 99m/Tc-TBI ...

Energy Technology Data Exchange (ETDEWEB)

Stress corrosion cracking tests in constant extension rate tensile (CERT) and constant load tensile (CLT) tests were conducted on Ni-xCr- 9Fe-yC in Ar, water, and a LiOH-boric acid solution. Cr and C improve the resistance of Ni-base alloys to IG cracking in both Ar and water at 360C. Since creep plays a role in IG cracking, one possible explanation for the role of the environment involves its effect on the creep. Experiments were conducted on the role of C in the deformation behavior and failure mode of Ni-16Cr-9Fe. Constant load experiments were conducted on Ni-16Cr-9Fe to determine if the CLT test is more aggressive than CERT. The electron backscattering technique in a SEM is being developed in order to extend the IG cracking studies to grain sizes typical of commercial alloys, 20-30 microns.

International Nuclear Information System (INIS)

Type 304 stainless steels (solution annealed material, cold worked material and fine grain material) were neutron irradiated to 3 x 10"2"5n/m"2 at 290degC and at 50degC. Each specimen was examined by SSRT test in high temperature water with 8 ppm dissolved oxygen and Ar gas environments. Results were as follows: (1) IASCC susceptibility of each material can be classified by 0.2% proof stress (PS) obtained from SSRT test in Ar gas: No IASCC susceptibility was observed in the PS range 850 MPa. (2) The uniform elongation (UE) in Ar gas environment decreased with increasing PS up to 800 MPa, and became about 0% in the PS range >800 MPa. (3) It was suggested that IASCC did not occur even if material had IASCC susceptibility, when under a condition that brittle fracture mechanism controls a specimen failure. (author)

Energy Technology Data Exchange (ETDEWEB)

The study presented in this thesis is a contribution toward improving the reliability of Metallized Polypropylene Film (MPPF) capacitors achieved by a better design. A temperature distribution in the roll is assumed with the aim of optimizing its thermal performance. It appears that the heating of long capacitor is higher than that of equivalent flat capacitor subjected to the same electric stresses. Standard accelerated aging tests (temperature and voltage) of MPPF capacitors have been performed with the aim to evaluate the dielectric performance and thus the capacitor lifetime. The statistical approach showed that the failure mode may be represented by two parameter Weibull distribution and the experimental approach proved that long capacitor deteriorates faster than a plate-shaped having the same features. Although capacitors with long geometry seem to have a poor pulse handling performance, we found that the quality of the, end-edge contact ...

International Nuclear Information System (INIS)

Many mechanical parts are subjected to stresses and strains that may eventually lead to their failure. In order to prevent the costly delays associated with equipment down-time, many parts have to be tested for weaknesses and defects when machinery is constructed or dismantled for maintenance. These procedures are known as Non-Destructive Testing (NDT) methods. Five types of non-destructive testing methods routinely used are radiographic testing, ultrasonic testing, magnetic particle inspection, liquid penetrant testing and eddy current testing. Out of these five techniques industrial radiography plays an important role in non-destructive testing to reveal interior defects in materials. In radiography almost two-thirds of the radiation reaching the film is scattered radiation which does not form the image of defects. Scattered radiation generated inside and outside a material has a very large effect on sensitivity of flaw detection since it ...

Science.gov (United States)

The Nuclear Regulatory Commission stipulates in 10 CFR 61 that disposed low-level radioactive waste (LLW) be stabilized. To provide guidance to disposal vendors and nuclear station waste generators for implementing those requirements, the NRC developed the Technical Position on Waste Form, Revision 1. That document details a specified set of recommended testing procedures and criteria, including several tests for determining the biodegradation properties of waste forms. Cement has been widely used to solidify LLW; however, the resulting waste forms are sometimes susceptible to failure due to the actions of waste constituents, stress, and environment. The purpose of this research program is to develop modified microbial degradation test procedures that will be more appropriate than the existing procedures for evaluating the effects of microbiologically influenced chemical attack on cement-solidified LLW. Groups of microorganisms indigenous to ...

Energy Technology Data Exchange (ETDEWEB)

Commercial focused ion beam (FIB) systems are commonly used to image integrated circuits (ICS) after device processing, especially in failure analysis applications. FIB systems are also often employed to repair faults in metal lines for otherwise functioning ICS, and are being evaluated for applications in film deposition and nanofabrication. A problem that is often seen in FIB imaging and repair is that ICS can be damaged during the exposure process. This can result in degraded response or out-right circuit failure. Because FIB processes typically require the surface of an IC to be exposed to an intense beam of 30--50 keV Ga{sup +} ions, both charging and secondary radiation damage are potential concerns. In previous studies, both types of effects have been suggested as possible causes of device degradation, depending on the type of device examined and/or the bias conditions. Understanding the causes of this damage is important for ICS that ...

UK PubMed Central (United Kingdom)

Heart failure affects nearly 6 million Americans, with a half-million new cases emerging each year. Whereas up to 50% of heart failure patients die of arrhythmia, the diverse mechanisms underlying...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

During the Bruce A Nuclear Generating Station (BNGS-A) Unit 1 1997 planned outage, a dew point search method identified a leak in one steam generator(SG) tube. Subsequently, the tube was inspected with all available eddy current probes and removed for examination. The initial inspection results and metallurgical examination of the removed tube confirmed that the leak was due to intergranular attack/stress corrosion cracking (IGA/SCC) emanating from the secondary side of the tube at the top of the tubesheet location. Subsequently, eddy current and ultrasonic indications were found at the top of the tubesheet of other Alloy 600 SG tubes. To investigate the source of the indications and to validate the inspection probes, sections of 40 tubes with various levels of damage were removed. The metallurgical examination of the removed sections showed that both secondary side and primary side initiated, circumferential, stress corrosion cracking and ...

UK PubMed Central (United Kingdom)

BackgroundProvision of consumer information and patient education are considered an essential part of chronic disease management programmes developed for patients with heart failure....Full Text Available

UK PubMed Central (United Kingdom)

Congestive heart failure (CHF) is a leading cause of morbidity and mortality. CHF is marked by atrial and ventricular enlargement and reduced cardiac contractility, as well as an association...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The most typical kinds of corrosion of brasses are selective corrosion (dezincification) and stress corrosion. Prevention against these kinds of corrosion lies in application of arsenic alloy addition and appropriate heat treatment removing internal stresses as well as in maintaining the arsenic and phosphorus contents on a proper level. The most typical corrosion of cupronickels is the local corrosion. Selective corrosion occurs less often and corrosion cracking caused by stress corrosion in sea water does not usually occur. Crevice corrosion is found especially in places of an heterogeneous oxidation of the surface under inorganic deposits or under bio-film. Common corrosive phenomena for brasses and cupronickels are the effects caused by sea water flow and most often the impingement attack. Alloy additions improve resistance to the action of intensive sea water flow but situation in this field requires further ...

UK PubMed Central (United Kingdom)

The oxidative stress theory of aging predicts that manipulations that alter oxidative stress/damage will alter aging. The gold standard for determining whether aging is altered is lifespan,...Full Text Available

Science.gov (United States)

PMID:4483135

Science.gov (United States)

PMID:476294

International Nuclear Information System (INIS)

A single exposure energy subtraction technique with a metal filter and an imaging plate for the Fuji Computed Radiography (FCR) system was developed for dual-energy subtraction radiography (DES) of the chest. By the use of this technique, 206 patients with suspected lung cancer were scanned in the clinical settings. The subtracted images in 200 patients, excluding six with poor image quality, were examined. Soft-tissue images (bone cancelled images) were useful in visualizing abnormality of the airway and nodules lying under the ribs; and bone images (soft-tissue cancelled images) in detecting rib metastases and the presence or absence of calcification in nodules. Additional information was acquired in 21 % (42/200). A single exposure is capable of neglecting motion artifacts. In addition, this technique may be of value in DES, which is considered to be one of the routine examinations, in view of low exposure doses. The need of conventional ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses how to overcome failures and pitfalls in software configuration management. (LSP)

Energy Technology Data Exchange (ETDEWEB)

Power system components, especially components failure, can significantly affect the reliability of a power system. Data about failure rate in electrical products were obtained from products life testing and analyzed in order to predict reliability. The distribution curve fitting method was used to estimate failure probability. Ten relays of different life times have been used to illustrate the validity of this analytical technique. 3 refs., 3 tabs.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Roentgenological analysis of the anterior chest wall was performed in twenty six patients with sternocostoclavicular hyperostosis. Initial hyperostotic change was seen at the first costosternal junction with ventral protrusion. Hyperostosis gradually developed around the first ribs, and irregular hyperostotic changes were also seen along the costoclavicular ligaments. Even in the final stage, however, sternoclavicular joint spaces were well preserved. These findings suggest that sternocostoclavicular hyperostosis is a disorder initiated around the costal cartilage including the periosteum and perichondrium, and that arthritis is not a condition stemming from that disorder.

International Nuclear Information System (INIS)

Extensive investigations and detailed analysis of the failure reason of 9DVN002ZV fan in Daya Bay Nuclear Power Station showed that the fan destroy was caused by the failure of non-drive end bear. The direct cause of this bearing' failure was its improper assembly caused by improper maintenance procedure, and the root cause was too small internal radial clearance after mounting. The factor affecting bearing internal radial clearance, the relationship between clearance and operating life time and fan failure process were discussed. (authors)

Energy Technology Data Exchange (ETDEWEB)

Waste is a heterogeneous fuel, often with high levels of chlorine, alkali and heavy metals. This leads to much more severe corrosion problems than combustion of fossil fuels. The corrosion rates of the materials used can be extremely high. Materials used for heat transferring parts are usually carbon steel or low alloyed steel. These are significantly cheaper than other steels. Austenitic stainless steel is also used, but is often avoided due to its sensitivity to stress corrosion cracking. More advanced materials, such as nickel base alloys, can be used in extremely aggressive environments. Since these materials are expensive and do not always have sufficient mechanical properties, they are often used as coatings on carbon steel tubes or as composite tubes. A new method, which shows good results at the first tests in plants, is electroplating with nickel. Plastic materials can be used in low temperature parts if the temperature does not exceed 150 deg C. A glass ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Background: Premature ovarian failure is diagnosed with a picture of amenorrhea, elevated follicle-stimulating hormone (FSH), and age under 40 years. Twenty percent (20%) of patients with premature ovarian failure have a concomitant autoimmune disease. Cases of premature ovarian failure associated with Sj?gren syndrome have been reported in the literature. Patient and method: We report a case of a 42-year-old white woman with Sj?gren syndrome and premature ovarian failure who underwent a reversal of her premature ovarian failure and restoration of normal menses using an elimination diet protocol. The patient was diagnosed with her rheumatological condition in 2005 and started on disease-modifying antirheumatoid drugs, which were taken intermittently due to a concern over medicatio...

Energy Technology Data Exchange (ETDEWEB)

An independent investigation of pipe welding leaks from the Low-Level Waste 2 (LLW2) Skid-B System for the possibilities of improper welding (IW), microbiologically influenced corrosion (MIC), sensitization, chloride pitting corrosion (CPC), and intergranular stress corrosion cracking (IGSCC) was conducted. The results show the prevailing mechanisms that caused the leaks are identified as IW, CPC, and the improper selection of weld filler material for the base metals in an environment of the North Plateau underground water. These is no evidence of MIC, sensitization, or IGSCC. The chloride pitting corrosion mechanism that took place at all the welds are also described. All the pipelines were replaced with polyvinyl chloride (PVC) for cost saving and the LLW2 Skid B System has been successfully operating since 1999. This report summarizes the findings and recommendations associated with preventive measures for future operations. The LLW2 Facility is a replacement ...

Energy Technology Data Exchange (ETDEWEB)

To study the fatigue life of extruded AZ31 (3%Al, 1%Zn, 0.3%Mn, Mg - the rest), AM50 (5%Al, 0.4%Mn, Mg - the rest) and ZK60 (5%Zn, 0.5%Zr, Mg - the rest) Mg alloys in air and NaCl-based solutions, corrosion fatigue tests were carried out using a rotating beam type fatigue machine. For the analysis of the corrosion fatigue behavior of Mg alloys in different environments, fitted N{sub sol}/N{sub air} ratio considered as a relative corrosion fatigue life is used. Here N{sub sol} and N{sub air} are the numbers of cycles to failure in the solution and in air, respectively. An extruded ZK60 alloy shows very high fatigue and corrosion fatigue properties in comparison with other alloys. However, ZK60 shows the lowest values of the relative fatigue life (N{sub sol}/N{sub air} {proportional_to}10{sup -3}-10{sup -2}) compared to that for AM50 and AZ31 alloys (N{sub sol}/N{sub air} {proportional_to}10{sup -2} - 10{sup -1}). Generally, extruded alloys in comparison to earlier ...

Science.gov (United States)

An instrument has been constructed for the measurement of residual stress in steel. If necessary, large objects can be examined in situ. An account is given of the principles and construction. A special stressing frame provides for calibration. An application to residual stress in gear blanks has established a systematic variation of surface stress with nickel content and confirmed the overall effect of the surface hardening treatment.

UK PubMed Central (United Kingdom)

We describe a 59-year-old patient who developed acute renal failure because of rhabdomyolysis after extensive red fire ant bites. This case illustrates a serious systemic reaction that may occur from...Full Text Available

UK PubMed Central (United Kingdom)

Forty-six patients with end-stage renal failure were subjected to iliac crest biopsy before the initiation of a dialysis programme and regardless of the presence of skeletal symptoms....Full Text Available

Science.gov (United States)

Angiotensin II has adverse actions in heart failure including vasoconstriction, aldosterone secretion, and activation of the sympathetic nervous system. Valsartan, a potent specific angiotensin II type 1 receptor blocker, may produce beneficial effects in heart failure. The purpose of this study was to evaluate the steady-state pharmacokinetics of valsartan 40, 80, and 160 mg each given every 12 h for 7 days in heart failure patients. Eighteen patients with chronic stable heart failure and left ventricular ejection fractions power model, showed that doubling the dose increased the AUC and Cmax 1.8 times. The pharmacokinetics of valsartan are predictable in heart failure patients within the dose range of 40-160 mg BID. Age did not appear to have influenced the valsartan clearance in heart failure patients. The pharmacokinetic values were higher in heart ...

UK PubMed Central (United Kingdom)

BackgroundAlthough dilated cardiomyopathy (DCM) is a leading cause of heart failure (HF), the mechanism underlying DCM is not well understood. Previously, it has been demonstrated...Full Text Available

UK PubMed Central (United Kingdom)

Premature menopause, ovarian failure younger than 40 years of age, is relatively rare but may preclude childbearing for some women who delay attempts at fertility. We present five kindreds in which...Full Text Available

UK PubMed Central (United Kingdom)

ObjectiveThe aim of this study was to ascertain whether all cervical cancer patients who received adjuvant concurrent chemoradiation (CCRT) for high risk of treatment failure after...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The reliability of an electrical power system is influenced by the operation of circuit-breaker (CB). A good indicator of circuit-breaker condition is its switching time. Based on it some of the critical circuit-breaker irregularities can be detected and removed before they develop to a failure. In this paper, the evaluation of time measurements (timings) in case of different failures will be carried out for two circuit-breaker solutions, i.e. with spring and hydraulic drive. Moreover, the relationships between switching time and failure type/location will be derived. Thereby, the influence of failure trend will also be taken into account. (author)

International Nuclear Information System (INIS)

Presented are the results of the investigation of the kinetics and micromechanism of the failure in impact bending of oriented-crystallized specimens having the eutectic composition Ni_3Al-Ni_3Nb and of the bimetal composed of 45 steel + M3 copper. The failure kinetics was studied by high-speed filming, whereas the fractures were studied by electron fractography. The particularities of the failure of the laminar-type composite materials were found. Analyzed was the effect of the kinetic factors and the mechanism of failure upon its energy consumption.

Science.gov (United States)

... with the additional US funds supporting Islamic ... the FATA and NWFP, keeping Pakistan's government and ... Without these madrassas, the TTP is left ...

Science.gov (United States)

Aluminum electrolytic capacitors, with 1043 failures, are a good example. Also, categorization by size and voltage reveals such frequencies of occurrence as ...

Science.gov (United States)

PMID:20173351

Science.gov (United States)

Destress blasting is commonly used as a stress control technique at the Galena Mine, Wallace, Idaho, where the U.S. Bureau of Mines maintains a cooperative research program with the mine operators (ASARCO). A digital seismic array and an array of borehole...

UK PubMed Central (United Kingdom)

Background. The Free Radical Theory of Aging mechanistically links oxidative stress to aging. Okinawa has among the world's longest-lived populations but oxidative stress in this...Full Text Available

UK PubMed Central (United Kingdom)

The alternative sigma factor ς^B of Bacillus subtilis is required for the induction of approximately 100 genes after the imposition of a whole range of stresses and...Full Text Available

UK PubMed Central (United Kingdom)

Social stress is prevalent in many facets of modern society. Epidemiological data suggest that stress is linked to the development of overweight, obesity and metabolic disease. Although there...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Stability concerns of the Par Pond Dam, an embankment structure in the Savannah River Site complex, resulted in a comprehensive evaluation of the state of its integrity. Specifically, excessive seepage through the embankment, slope failure due to an earthquake event as well as liquefaction potential of the embankment and the foundation are addressed and the potential of failure is evaluated. Lastly, remedial benefits of the addition of a berm structure are also assessed.

UK PubMed Central (United Kingdom)

AimsThe prevalence and importance of liver function test (LFT) abnormalities in a large contemporary cohort of heart failure patients have not been systematically evaluated.Full Text Available

UK PubMed Central (United Kingdom)

1 The decreased binding of drugs and dyes to plasma proteins from male and female rats with acute renal failure has been investigated using equilibrium dialysis at 37 degrees C. 2 Acute renal failure...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A plane stress constitutive relation is developed for laminate composites undergoing matrix cracking and therefore displaying significant nonlinear stress-strain behavior. The constitutive relation is similar in some respects to a phenomenological theory of plasticity in that it is fit to data from uniaxial tests. The constitutive equations are specialized to brittle matrix composites (especially CMCs) in the form of cross-piles and quasi-isotropic laminates. Several problems involving stress redistribution at holes and notches due to nonlinear stress-strain behavior are investigated with the aid of the constitutive law.

Science.gov (United States)

... Accession Number : ADD421949. Title : Ultimate Compressive Strength and Nonlinear Stress-Strain Curves of Graphite/Epoxy Laminates,. ...

UK PubMed Central (United Kingdom)

Like few other organs, the skin is continuously exposed to multiple exogenous and endogenous stressors. Superimposed on this is the impact of psychological stress on skin physiology and pathology....Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Background Stimulated by the concept of Natural Orifice Transluminal Endoscopic Surgery (NOTES), minimizing the access even further has become a new trend in minimally invasive surgery. We compare our recently described new method of endoscopic single-access adrenalectomy with the conventional retroperitoneoscopic approach in a matched-pairs study. Methods Fifty single-access retroperitoneoscopic adrenalectomies (SARA) were performed in 47 selected patients suffering from Conn?s adenomas (n?=?20), pheochromocytomas (n?=?15), Cushing?s adenomas (n?=?6), and other diseases (n?=?6). For SARA, a single 2-cm skin incision beneath the 12th rib was used. Following creation of the retroperitoneal space with the rigid endoscope, dissection was carried out single-handed. Another 47 patients served a...

International Nuclear Information System (INIS)

Local control of Ewing's sarcoma was analysed in a series of 67 patients treated by surgery and/or radiotherapy as well as combination chemotherapy. Radiotherapy was employed with or without surgery in 60 patients and produced an overall local control rate of 55%; complete excision of the primary lesion seemed to be beneficial. There was a marked variation in control rates depending on the site of the primary lesion: limb 85%, rib 53%, pelvis 31% and other sites 33%.Primary tumours greater than 10 cm in diameter were significantly less likely to be controlled. Using daily fractions of approximately 180 cGy, total doses in excess of 6000 cGy seem more likely to produce serious late morbidity amd may not increase the local control rate. No cases of second malignancy arising in irradiated tissue have been observed to date, but one patient developed acute lymphoblastic leukaemia. (author).

Energy Technology Data Exchange (ETDEWEB)

A totally-enclosed, fan-cooled, rib-cooled type induction motor is adopted for an exhauster which is to be installed in a ventilation station for dust catcher in a tunnel. It has the highest capacity in Japan for the above purpose, and is provided with a cooling fan inside to recirculate cooled air, thereby improving cooling efficiency and reducing size and weight. Three-row combined angular ball bearings are used as the thrust bearings, and grease lubrication system is adopted to simplify the inspection/maintenance works. It is to be delivered to Japan Highway Public Corporation's Shizuoka Construction Bureau, Yaizu site office. Its electric specifications are 455 kW, 440 V, 890 A and 510 rpm, and its mechanical specifications are thrust load: 16 kN and impeller load: 7.2 kN. (translated by NEDO)

Energy Technology Data Exchange (ETDEWEB)

Microelectronic failure analysis (FA) has been an integral part of the development of state-of-the-art integrated circuits. FA of MicroElectroMechanical Systems (MEMS) is moving from its infancy stage to assume an important role in the successful design, fabrication, performance and reliability analysis for this new technology. In previous work, the authors focused on the application of several techniques developed for integrated circuit analysis to an earlier version of a surface micromachined microengine fabricated at Sandia. Recently, they have identified important new failure modes in binary counters that incorporate a newer design of the microengine, using a subset of integrated circuit failure analysis techniques including optical microscopy, focused ion beam (FIB) techniques, atomic force microscopy (AFM), and scanning electron microscopy (SEM). The primary failure mode they have identified is ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Environmental Research Database

DescriptionNot supplied.

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

Wastenet

aged gracefully: premature and accelerated corro - sion, erosion, and stress are raising maintenance costs.Last

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Heat transfer augmentation techniques (passive, active or a combination of passive and active methods) are commonly used in areas such as process industries, heating and cooling in evaporators, thermal power plants, air- conditioning equipment, refrigerators, radiators for space vehicles, automobiles, etc. Passive techniques, where inserts are used in the flow passage to augment the heat transfer rate, are advantageous compared with active techniques, because the insert manufacturing process is simple and these techniques can be easily employed in an existing heat exchanger. In design of compact heat exchangers, passive techniques of heat transfer augmentation can play an important role if a proper passive insert configuration can be selected according to the heat exchanger working condition (both flow and heat transfer conditions). In the past decade, several studies on the passive techniques of heat transfer augmentation have been reported. The present paper is a review on progress ...

Energy Technology Data Exchange (ETDEWEB)

A numerical package called RESID has been assembled to calculate the residual stresses in VAWT blades induced during cold forming. Using a strength of materials - elementary beam theory approach, RESID models the material response with a bilinear stress-strain curve, and the cross-sectional geometry with an array of area increments. Through an iterative solution procedure residual stresses are predicted for a specified final radius of curvature or applied bending moment. RESID results are compared to theoretical solutions for simple geometries and with MARC Finite element results for VAWT blade geometries. Calculating residual stress levels, determining acceptable residual stress levels, and a method of reducing residual stresses are discussed. A complete listing and sample run are included in the appendicies.

Science.gov (United States)

Minimum weight design is an important criterion in aircraft and spacecraft because it allows either an increased pay-load or higher performance. As a result, the use of composite sandwich panels has grown due to their light weight and high rigidity. In order to further increase the efficiency of these structures, designers have used different materials in different shapes in the facesheets and in the core. One of the most recent innovations has been the use of a uniform net of carbon fibre/epoxy as the facesheets. In the present study, the optimal design of sandwich plates with heterogeneous, facesheets is treated. The plate mass is minimized, considering the first natural frequency and certain failure loads as constraints. Weight reduction is obtained by defining a nonuniform distribution of composite material in the facesheets. Initially, the facesheets are assumed to be constructed of composite strips in a regular pattern. During the optimization process, both ...

Energy Technology Data Exchange (ETDEWEB)

The shot peening of the outer surface of Alloy 800 is proposed by the steam generator supplier in order to increase the stress corrosion cracking resistance of the tubes. The benefits and drawbacks of such a treatment are evaluated, focusing on the main concern i.e. a possible enhanced tendency of stress corrosion cracking at the transition of the expanded tube-to-tubesheet joint. Stress corrosion tests as well as residual stresses measurements demonstrate no significant difference between peened and unpeened tubes at that location. The other concerns such as stability of the compressive stresses, increased risk of pitting or intergranular attack and pollution of the secondary circuit by fragmented beads appear the as minor concerns.

Energy Technology Data Exchange (ETDEWEB)

Polyethylene gas piping is expected to be in service for times on the order of 50 years depending on service conditions. Therefore research research on piping materials and pipes has two principal objectives: (a) developing methods for predicting when a pipe will fail and (b) improving the material for piping. The prediction of long time failure hinges on the development of short time test methods which relate to long time failure. The improvement in the behavior of current materials also hinges on the use of test methods of short duration relative to the anticipated life time of the pipe in service. One of the primary criterion for an acceptable test method is that it produces the same type of failure as is observed after long time failure in service. It has been found that P.E. pipe material fails in a brittle mode after long periods of time. The failure mode is called brittle ...

Energy Technology Data Exchange (ETDEWEB)

Airborne pollutants can cause failures in switching and computing equipment. This paper focuses on a subset of such pollutants - airborne fine particles (<2.5 [mu]m diameter). It begins by examining the extent to which different improvements in heating, ventilating and air conditioning (HVAC) systems reduce indoor concentrations of fine particles. For each modification, the consequent reduction in soiling rate is derived. The concomitant increase in operating costs is also calculated. These costs are then compared with the costs of failures in telephone switching offices, leading to estimates of failure rate reductions that would make improvements cost-effective. Finally, the reduction in failures required to offset the costs of the improvements are compared with documented differences in failure rates between unimproved and improved environments. This study suggests that, in ...

International Nuclear Information System (INIS)

This study describes the formulations to optimize the time interval of inspections and/or replacements of equipment/parts taking into account the probability density functions (PDF) for failure rates and parameters of failure distribution functions (FDF) and evaluates the optimized results of these time intervals using our formulations by comparing with those using only representative values of failure rates and the parameters of FDF instead of using these PDFs. The PDFs are obtained with Bayesian method and the representative values are obtained with likelihood estimation method. However, any significant difference is not observed between both optimized results within our preliminary calculations. (author)

International Nuclear Information System (INIS)

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(#+-#5)% and 90(#+-#5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author).

Energy Technology Data Exchange (ETDEWEB)

The wind industry has experienced premature turbine component failures during the past years. With the increase in turbine size, these failures, especially those found in the major drivetrain components, i.e. main shaft, gearbox, and generator, have become extremely costly. Given that the gearbox is the most costly component in the drivetrain to fix, the National Renewable Energy Laboratory (NREL) initiated the Gearbox Reliability Collaborative (GRC) to determine the causes for premature gearbox failures and subsequently, recommend improvements to gearbox design, manufacture, and operational practices. The GRC has two identical test gearboxes, which are planned for a dynamometer and a field test, respectively.

Energy Technology Data Exchange (ETDEWEB)

Anisotropy finite element analysis was performed to study stresses associated with the tetragonal precipitates and the tetragonal to monoclinic transformation in MgO partially stabilized zirconia. Stresses were assumed to be caused by the lattice misfits between the product phase and the parent phase. In the finite element calculations, the tetragonal and monoclinic precipitates were assumed to be lenticular in shape, and the anisotropic elastic constants of the cubic, tetragonal and monoclinic phases were considered. The purpose of this paper is to obtain some knowledge about how stresses respond when the microstructure is changed, and how stress fields affect microstructure development. The finite element results show that increasing a{sub t}/a{sub c} and decreasing c{sub t}/a{sub c} can create a favorable stress field to reduce the growth rate of tetragonal precipitates during ...

Science.gov (United States)

Ultimate Compressive Strength = 3000.0 psi. 3.0 Failure Criteria. The structural criteria used to evaluate the combustor components was chosen ...

Science.gov (United States)

of the Intelligent Control System (ICS) for reusable rocket engines. .... the incoming measurements with corresponding estimates, a sensor failure can be ...

Science.gov (United States)

Kidney Failure, Chronic

Science.gov (United States)

The location of defective LMFBR fuel pins by the determination of gas tag isotopic ratios is discussed. The application of this method to the FFTF Reactor briefly described.

Energy Technology Data Exchange (ETDEWEB)

Corrosion failures in circuits of foreign NPPs are considered. According to American statistics there are more corrosion failures in two-circuit NPPs than in NPPs with one circuit. Steam generators mostly suffer from ''corrosion denting''. Lately pitting corrosion becomes a potentially serious problem. Steam generator vertical tubes are mainly subjected to this corrosion type. Attention is drawn to intercrystalline corrosion. The causes of corrosion are described. The problem of optimization of structural materials is discussed to reduce corrosion failures as well as other methods of decreasing corrosion failures. Organization of nondestructive testing, increased requirements to water and steam purity are of great importance.

Science.gov (United States)

... position must not be penalized in their NCO Evaluation Report (NCOER). ... failure to perform MOS-, SQI-, or ASI-related duties after counseling. ...

Energy Technology Data Exchange (ETDEWEB)

Natural fractures and in situ stresses commonly dictate subsurface reservoir permeability and permeability anisotropy, as well as the effectiveness of stimulation techniques in low-permeability, natural gas reservoirs. This paper offers an initial prediction for the orientations of the fracture and stress systems in the tight gas reservoirs of the Frontier Formation, in the Green River basin of southwestern Wyoming. It builds on a previous report that addressed fractures and stresses in the western part of the basin and on ideas developed for the rest of the basin, using the principle that thrust faults are capable of affecting the stress magnitudes and orientations in little-deformed strata several hundreds of kilometers in front of a thrust. The prediction of subsurface stresses and natural fracture orientations is an undertaking that requires the willingness to revise models as ...

Energy Technology Data Exchange (ETDEWEB)

Approximately 95% of the world`s integrated chips are packaged using a hot, high pressure transfer molding process. The stress created by the flow of silica powder loaded epoxy can displace the fine bonding wires and can even distort the metalization patterns under the protective chip passivation layer. In this study the authors developed a technique to measure the mechanical stress over the surface of an integrated circuit during the molding process. A CMOS test chip with 25 diffused resistor stress sensors was applied to a commercial lead frame. Both compression and shear stresses were measured at all 25 locations on the surface of the chip every 50 milliseconds during molding. These measurements have a fine time and stress resolution which should allow comparison with computer simulation of the molding process, thus allowing optimization of both the manufacturing process and mold ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this study is to develop the methodology which enables to identify the mechanical properties of element such as stress intensity factor by using the AE parameters. Considering the multivariate and nonlinear properties of AE parameters such as ringdown count, rise time, energy, event duration and peak amplitude from fatigue cracks of machine element the principal component regression(PCR) and artificial neural network(ANN) models for the estimation of stress intensity factor were developed and validated. The AE parameters were found to be very significant to estimate the stress intensity factor. Since the statistical values including correlation coefficients, standard mr of calibration, standard error of prediction and bias were stable, the PCR and ANN models for stress intensity factor were very robust. The performance of ANN model for unknown data of stress intensity ...

UK PubMed Central (United Kingdom)

BackgroundSelection programs for growth and stress traits in cultured fish are fundamental to the improvement of aquaculture production. The gilthead sea bream (Sparus aurata)...Full Text Available

UK PubMed Central (United Kingdom)

PurposeHeavy metals and other forms of oxidative stress have been implicated as key factors in the formation of age-related cataract in humans. Metallothioneins are...Full Text Available

UK PubMed Central (United Kingdom)

p53 plays a critical role in tumor suppression. As a transcription factor, in response to stress signals, p53 regulates its target genes and initiates stress responses, including cell cycle arrest,...Full Text Available

UK PubMed Central (United Kingdom)

The ability to respond to stress is at the core of an organism's survival. The hormones epinephrine and norepinephrine play a central role in stress responses in mammals, which require the synchronized...Full Text Available

UK PubMed Central (United Kingdom)

Oysters are permanently exposed to various microbes, and their defense system is continuously solicited to prevent accumulation of invading and pathogenic organisms. Therefore, impairment of the animal's...Full Text Available

UK PubMed Central (United Kingdom)

A barley (Hordeum vulgare L.) mutant (Az34) has been identified with low basal levels of abscisic acid (ABA) and with reduced capacity for producing ABA in response to water stress....Full Text Available

UK PubMed Central (United Kingdom)

The widely accepted oxidative stress theory of aging postulates that aging results from accumulation of oxidative damage. Surprisingly, data from the longest-living rodent known, naked mole-rats [MRs;...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundAn earlier study showed that a week of yoga practice was useful in stress management after a natural calamity. Due to heavy rain and a rift on the banks of the Kosi river,...Full Text Available

UK PubMed Central (United Kingdom)

The effect of water stress on patterns of nitrate reductase activity in the leaves and nodules and on nitrogen fixation were investigated in Medicago sativa L. plants watered 1 week...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A discussion of how stress and strain affect the quantities which can be measured in an NQR experiment shows that, for stresses of the magnitude to be expected at depths up to about 10,000 feet, quadrupole coupling constants will fall in the range of 1 to 10 kHz for both the sodium and chloride ions in NaCl. The most promising system involves pulsed nuclear double resonance detection; and alterative is to observe the quadrupolar splitting of the NMR signal. Choices to be made in the measurement and mapping techniques are discussed. The well-known perturbation of the homogenous stress field in the neighborhood of a borehole is shown to be advantageous from the point of view of obtaining directional information on the stress. Construction and operation of a borehole stress sensor are considered. The NQR technique seems feasible for measuring the magnitude and direction of underground ...

Science.gov (United States)

This report is a continuation of the former efforts to elucidate the behavior of ferrocement concrete in static and dynamic stress fields. The influence of various reinforcements on pre and post cracking of thin sections forms the main topic of this repor...

UK PubMed Central (United Kingdom)

Oxidative stress has been implicated in the etiology of age-related muscle loss (sarcopenia). However, the underlying mechanisms by which oxidative stress contributes to sarcopenia have not been thoroughly...Full Text Available

UK PubMed Central (United Kingdom)

Accumulation of molecular damage and increased molecular heterogeneity are hallmarks of cellular aging. Mild stress-induced hormesis can be an effective way for reducing the accumulation of molecular...Full Text Available

UK PubMed Central (United Kingdom)

Neurons in the hippocampal CA1 region are particularly sensitive to oxidative stress (OS), whereas those in CA3 are resistant. To uncover mechanisms for selective CA1 vulnerability to OS, we...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundA strong association between stress resistance and longevity in multicellular organisms has been established as many mutations that extend lifespan also show increased...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundClara cell protein (CC16), the main secretory product of bronchiolar Clara cells, plays an important protective role in the respiratory tract against oxidative stress and...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundTrichloroethylene (TCE) may induce oxidative stress which generates free radicals and alters antioxidants or oxygen-free radical scavenging enzymes.MethodsTwenty...Full Text Available

UK PubMed Central (United Kingdom)

Small RAC/ROP-family G proteins regulate development and stress responses in plants. Transient overexpression and RNA interference experiments suggested that the barley (Hordeum vulgare)...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Iron undergoes a polymorphic phase transformation from alpha phase (bcc) to the epsilon phase (hcp) when compressed to stresses exceeding 13 CPa. Bccause the epsilon phase is denser than the alpha phase, a single shock wave is unstable and breaks up into an elastic wave, a plastic wave, and a phase transition wave. Examination of this structured wave coupled with various phase transformation models has been used to indirectly examine the transition kinetics. Recently, multimillion atom simulations (molecular dynamics) have been used to examine the shock-induced transition in single crystal iron illustrating an orientation dependence of the transition stress, mechanisms, and kinetics. The objective of the current work was to perform plate impact experiments to examine the shock-response of polycrystalline and single crystal iron with nanosecond resolution for impact stresses spanning the {alpha} - {epsilon} transition. The ...

UK PubMed Central (United Kingdom)

BackgroundBallet Dancers have been shown to have a relatively high incidence of stress fractures of the foot and ankle. It was our objective to examine MR imaging patterns of bone...Full Text Available

UK PubMed Central (United Kingdom)

The aim of the present study was to evaluate the ameliorative potential of quercetin (QC) against paracetamol (PCM)-induced oxidative stress and biochemical alterations in mice blood. A total of 36...Full Text Available

UK PubMed Central (United Kingdom)

Biological membranes are lamellar structures composed of two leaflets capable of supporting different mechanical stresses. Stress differences between leaflets were generated during micromechanical experiments...Full Text Available

International Nuclear Information System (INIS)

The unsteady flow and heat transfer are simulated using LES and DNS for a channel with two angled ribs as a vee-shaped vortex generator to augment heat transfer. The vortex generators are attached on the bottom wall of the channel and their angles in respect to the main flow are between 10"o and 30"o. The Prandtl number is 0.71 and the Reynolds numbers based on the inflow velocity and the height of channel are from 200 to 2000. Based on the results of this work, the variations of the Nusselt number, pressure coefficient, bulk temperature, friction factor and Colburn factor with the Reynolds numbers and the incidence angles are provided. The relation between the key parameters of the velocity (friction factor f) and thermal (Colburn factor J) boundary layers is calculated for all cases and their values are compared with the predicted values by the Chilton-Colburn analogy. A comparison between the DNS and LES results is performed and it is found that relatively ...

International Nuclear Information System (INIS)

In an effort to evaluate the feasibility of introducing computed radiography (FCR) into mass screening for lung cancer, the ability of FCR to detect nodules one cm in diameter was examined using a humanoid chest phantom. Based on the receiver operating characteristic (ROC) analysis, the detectability of FCR was compared with that of conventional radiography and photofluorography. The values of area under ROC curves were higher for FCR (0.963 for image similar to that with conventional film-intensifying screen system, image A; and 0.952 for processed image, image B) than the other two methods (0.774 for radiography and 0.789 for photofluorography). Degradation of image quality in FCR could be avoided by a wide latitude even if proper exposure techniques might not be employed. Images A and B in FCR yielded excellent delineation for nodules in the lung field and in the retrocardiac and subdiaphragmatic regions, respectively. This may have implications for the value of simultaneous ...

Energy Technology Data Exchange (ETDEWEB)

Isobaric contaminants are often problematical in accelerated negative ion beams for research at certain radioactive ion beam (RIB) and accelerator mass spectrometry (AMS) facilities since their presence in low-intensity rare isotopic beams seriously compromise experimental results. This article describes a non-resonant, laser-based photo-detachment apparatus for use at these facilities, which, according to calculations efficiently removes isobaric contaminants from these beams. The advantage of the system for isobaric contaminant removal over other systems proposed to date lies in its ability to efficiently capture easily transportable energetic negative ion beams with low, intermediate or high energy spreads by a superconducting solenoid magnetic field. The ability to change the diameter of captured beams by adjusting the magnetic field strength permits optimum control of the radial overlap of the laser/negative ion beam profiles over an extended interaction ...

International Nuclear Information System (INIS)

Failure of multiple components due to a common cause represents one of the most important issues in evaluation of system reliability or unavailability. The frequency of such events has relatively low expectancy, when compared to random failures, which affect individual components. However, in many cases the consequence is a direct loss of safety system or mitigative safety function. For this reason, the modeling of a common cause failure (CCF) and its presentation in fault tree structure is of the uttermost importance in probabilistic safety analyses (PSA). Amongst the different techniques available to reduce the impact of common cause failures, the most important operations related technique, is that of staggered testing. In the TAPP 3,4 Level-1 PSA it was found that the contribution of Common Cause Failures to the Core Damage Frequency (CDF) was significant. The Common Cause ...

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the calculation of availability for parallel transmission lines (two or more) in the same tower or on the same right of way. As in many studies, the development of mathematical models is an important step. The models are justified using historical data and known characteristics of power system elements. A statistical method was used to generalize the failure rate and repair rate from real operating data. Application of the new model (which combines common-mode, simultaneous independent, and dependent outages) is discussed.

Energy Technology Data Exchange (ETDEWEB)

The paper presents results of studies on the effect of heat treatment on strength and pattern of 40Kh steel impact failure. Loading levels corresponding to macroscopic spalling microdamage initiation in the material are determined for three initial states. Metallographic study on the spalling failure pattern for 40Kh steel in different initial states and data on microhardness measurement are presented.

International Nuclear Information System (INIS)

A historical overview of corrosion problems found in power plant condensers and mitigation procedures is presented. The paper is organized according to alloy type and failure mode. Alloys considered are copper-base alloys, stainless steels and titanium. Failure modes discussed include erosion-corrosion, sulfide attack, environmentally assisted cracking, galvanic corrosion, steam condensate corrosion, pitting corrosion, and dealloying. Mitigation procedures discussed include cathodic protection, ferrous ion injection, as well as tube cleaning and layup practices.

Science.gov (United States)

... 2,000 230.102Tender plain bearing journal boxes: Failure to repair 1,000 1,500 230.103Tender roller bearing journal boxes: Failure to properly maintain 1,000 1,500 230.104Driving box shoes and wedges:...

Energy Technology Data Exchange (ETDEWEB)

We report a case of stress fracture of the clavicle associated with sternocostoclavicular hyperostosis. A 60-year-old man sustained a stress fracture of the right clavicle with no history of trauma. On radiography, hyperostosis of the anterior chest wall and ankylosis of the sternoclavicular joint were evident in addition to the fracture. Fracture healing was uneventful after 2.5 months. Ankylosis of the sternoclavicular joint may have caused increased stress at the midshaft of the clavicle by daily activity or minor trauma. Such a fracture is a rare complication of sternocostoclavicular hyperostosis. (orig.)

Science.gov (United States)

... without the problem of purple plague. The Au-Ni-In evaporated ... surface and bonding degradation (purple plague) St step-stress ...

Science.gov (United States)

PMID:534760

International Nuclear Information System (INIS)

... Yoshiaki Toshiba Corp., Nuclear Power Division, Yokohama, Kanagawa (Japan)

Energy Technology Data Exchange (ETDEWEB)

On February 9, 1995 ComEd experienced a pipe type cable failure on 138kV line 13717. Line 1737 is a bulk power transmission cable circuit connecting The Fisk and Crawford generating stations located within city limits. The line is approximately 4.5 miles long and was originally installed in 1975. This line is forced cooled, has 2,500 KCMIL copper conductors with 505 mils of paper insulation in an 8 inch pritec coated steel pipe. The splices are constructed with Voltalit castings. The failure occurred approximately 3,500 feet from Crawford Station. It was easy to locate the failure since the cable joint casing was breached resulting in the loss of approximately 2,600--2,700 gallons of dielectric fluid. Upon field examination B Phase was determined to have failed. The failure occurred 12 inches inside the casing in an area where it was impossible to install a long connector or add an additional short ...

Energy Technology Data Exchange (ETDEWEB)

A 25m wind turbine blade was tested to failure when subjected to a flapwise load. With the test setup, it was possible to test the blade to failure at three diffe-rent locations. The objective of these tests is to learn about how a wind turbine blade fails when exposed to a large flapwise load and how failures propagate. The report shows also results from ultra sonic scan of the surface of the blade and it is seen to be very useful for the detection of defects, especially in the layer between the skin laminate and the load carrying main spar. Acoustic emission was successfully used as sensor for the detection of damages in the blade during the test. The report contains measurements of the total deflection of the blade, the local deflection of the skin and the load carrying main spar and also measurement of strain all as a function of the applied load and up to failure of the blade. The 'post ...

International Nuclear Information System (INIS)

As part of the Nondestructive Evaluation Reliability Program sponsored by the US Nuclear Regulatory Commission, the Pacific Northwest Laboratory is developing a method that uses risk-based approaches to establish in-service inspection plans for nuclear power plant components. This method uses probabilistic risk assessment (PRA) results and Failure Modes and Effects Analysis (FEMA) techniques to identify and prioritize the most risk-important systems and components for inspection. The Surry Nuclear Power Station Unit 1 was selected for pilot applications of this method. The specific systems addressed in this report are the reactor pressure vessel, the reactor coolant, the low-pressure injection, and the auxiliary feedwater. The results provide a risk-based ranking of components within these systems and relate the target risk to target failure probability values for individual components. These results will be used to guide the development of ...

Energy Technology Data Exchange (ETDEWEB)

Stress relaxation was studied at 408 K on AZ31 reinforced by ceramic foam produced by in situ foaming of filler loaded preceramic polymer melt. Reinforcement causes significant enhancement of the resistance against stress relaxation compared to AZ91. It is correlated with hardening by the ceramic skeleton as well as ceramic particles formed in the AZ31-matrix. (orig.)

UK PubMed Central (United Kingdom)

Stress exposure increases the risk of addictive drug use in human and animal models of drug addiction by mechanisms that are not completely understood. Mice subjected to repeated forced swim stress...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The AP-0 Target Hall Collection Lens is a pulsed device which focuses anti-protons just downstream of the Target. Since the angles at which the anti-protons depart the Target can be quite large, a very high focusing strength is required to maximize anti-proton capture into the downstream Debuncher Ring. The current design of the Collection Lens was designed to operate with a focusing gradient of 1,000 T/m. However, multiple failures of early devices resulted in lowering the normal operating gradient to about 750 T/m. At this gradient, the Lens design fares much better, lasting several million pulses, but ultimately still fails. A Finite Element Analysis (FEA) has been performed on this Collection Lens design to help determine the cause and/or nature of the failures. The Collection Lens magnetic field is created by passing high current through a central conductor cylinder. A uniform current distribution through the cylinder will create a ...

Energy Technology Data Exchange (ETDEWEB)

In order to perform the structural analysis and stress evaluation for frame structures in the nuclear power plants, ADAMS (AIJ Design Analysis and Modules System) has been developed by the addition of the following functions to the ICES-STRUDL system. 1. Load combination and stress evaluation on the basis of specifications for designing steel structure (issued by the Architecture Institute of Japan). 2. Combination of load and stress evaluation of piping support on the basis of the regulations of Ministry of International Trade and Industry. 3. Addition of other functions than that described above. ADAMS enables structural analysis and stress evaluation exactly and efficiently not only for a large scale structure such as the pipe whip protection structure installed inside of the primary containment vessel for many loading cases but also for a large number of structures such as piping support. This ...

British Library Electronic Table of Contents (United Kingdom)

A kind of metastable beta titanium alloy, i.e. Ti-10Mo-8V-1Fe-3.5Al, was aged under elastic compressive stress. Transmission electron microscopy (TEM) investigations revealed that, in the stress-aged samples, precipitated alpha plates were parallel to each other. However, in the conventionally aged samples, alpha plates intersected each other. In other words, variant of alpha plate was selected in the stress-aged samples. Tensile tests showed that, at equivalent tensile strength, the stress-aged samples exhibited higher ductility, compared to the conventionally aged ones.

British Library Electronic Table of Contents (United Kingdom)

Maternal stress during pregnancy, particularly that combined with low socioeconomic status (SES), has been linked to an increased risk for impaired behavioural and emotional development and affective disorders in children. In animal models, acute periods of prenatal stress have profound effects on hypothalamo-pituitary-adrenal (HPA) function and behaviour. However, few studies have determined the impact of chronic exposure to stress in animal models. The objective of this study was to determine the effects of chronic maternal stress (CMS) during the 2nd half of pregnancy and nursing on growth, locomotor behaviour and HPA axis function in juvenile guinea pig offspring. Pregnant guinea pigs were exposed to a random combination of variable stressors every other day over the 2nd half of gestat...

International Nuclear Information System (INIS)

A numerical study of a natural convection in a rectangular cavity with the low-Reynolds-number differential stress and flux model is presented. The primary emphasis of the study is placed on the investigation of the accuracy and numerical stability of the low-Reynolds-number differential stress and flux model for a natural convection problem. The turbulence model considered in the study is that developed by Peeters and Henkes (1992) and further refined by Dol and Hanjalic (2001), and this model is applied to the prediction of a natural convection in a rectangular cavity together with the two-layer model, the shear stress transport model and the time-scale bound #upsilon#"2-f model, all with an algebraic heat flux model. The computed results are compared with the experimental data commonly used for the validation of the turbulence models. It is shown that the low-Reynolds-number differential stress and ...

International Nuclear Information System (INIS)

The combined effects of environment, yield strength and stress state on the cracking susceptibility of beta-extruded Ti-6Al-6V-2Sn have been examined. At a constant yield strength and under plane strain conditions, the stress intensity required for slow crack propagation decreased as the severity of the environment increased, i.e., from laboratory air to 3.5% NaCl. Furthermore, the crack propagation rates were a function of both stress intensity, and environmental severity. Although the fracture toughness and threshold stress intensities for slow crack growth generally decreased with increasing yield strength, aging, which resulted in the precipitation of ordered Ti3Al particles in the primary alpha phase, tended to accentuate the susceptibility of this alloy to sustained load/stress corrosion cracking. Finally, at constant yield strength, the sustained load cracking threshold ...

Science.gov (United States)

The main purpose of this paper is to explore a numerical algorithm for determining the contact stress when a circular crowned roller is compressed between two plates. To start with, the deformation curve on a plate surface will be derived by using the contact mechanical model. Then, the contact stress distribution along the roller which occurs on the plate surface is divided into three parts: from the center of contact to the edge, the edge and apart from the contact line. The first part is calculated by the elastic contact theorem for the contact subjected to nominal stress between non-crowned parts of roller and plates, the second part is obtained by the classical Hertzian contact solution for the contact between crowned parts of roller and plates, and the third part is simulated as exponential decay. In order to overcome the defect of the half space theorem, in which a plate with infinite thickness is assumed initially, ...

British Library Electronic Table of Contents (United Kingdom)

Customer Relationship Management (CRM) systems can help organizations manage customer interactions more effectively. Like many new technologies, CRM has been accompanied by vendor hype and stories of implementation failure. Work on critical success factors (CSFs) should encourage more appropriate implementation practice; however many CSF studies conclude with a list of factors but provide little further guidance. In particular, there is a need for stronger theoretical models of the entire CRM innovation process which can be used by managers to understand better the underlying causes of success and failure. This paper adopts a novel approach to this problem by firstly developing a conceptual model of CRM innovation and then converting this model into a dynamic simulation model. Some early s...

International Nuclear Information System (INIS)

The performance of steam generator tubes in water-cooled nuclear power reactors has been reviewed for 1979. Tube failures occurred at 38 of the 93 reactors surveyed. Causes of these failures and procedures designed to deal with them are described. The defect rate was twice that in 1978 but still lower than the two previous years. Methods being employed to detect defects include increasing use of multifrequency eddy-current testing and a trend to full-length inspection of all tubes. To reduce the incidence of tube failures by corrosion, plant operators are turning to full-flow condensate demineralization and more leak-resistant condenser tubes. (author).

British Library Electronic Table of Contents (United Kingdom)

Design rules for robustness require insensitivity to local failure and the prevention of progressive collapse. This is often verified by applying the load case ''removal of a limited part of the structure''. This paper will evaluate typical structural systems for large-span timber roof structures against these requirements, comparing the results against typical reasons for damages and failures. Applying the finding that most failures of timber structures are not caused by random occurrences or local defects, but by global (repetitive) defects (e.g. from systematic mistakes), it is shown that the objective of load transfer-often mentioned as preferable-should be critically analysed for such structures. Based on these findings, proposals for structural systems and details towards a robust de...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem Porcelain fracture associated with an implant-supported, metal ceramic crown or fixed partial denture occurs at a higher rate than in tooth-supported restorations, according to the literature. Implant-specific and patient-specific causes of ceramic failure have not been fully evaluated. Purpose The purpose of this retrospective study was to evaluate the potential statistical predictors for porcelain fracture of implant-supported, metal ceramic restorations. Material and Methods Over a 6-month period, a consecutive series of patients having previously received implant-supported, metal ceramic fixed restorations were examined during periodic recall appointments. The number of supporting implants, number of dental units, type of restoration, date of prosthesis insertion, ...

British Library Electronic Table of Contents (United Kingdom)

Reference failures, and their increase in affectively negative conditions (known as affective reactivity of speech), are more frequently observed in schizophrenia patients than in normal controls, but no information is available comparing schizophrenia with depression, ie, a mental disorder closely linked to the concept of affective reactivity. To address this gap in the literature, the present study compared 24 schizophrenia inpatients, 21 unipolar depression inpatients and 21 normal controls. Two 10-minute conversational speech samples (1 on negative and 1 on positive memories) were collected from each patient. The transcripts of the audiotaped interviews were analyzed blindly for frequencies of 6 types of referential failures, employing the Communication Disturbances Index, adapted for ...

Energy Technology Data Exchange (ETDEWEB)

Twenty-two out of 31 patients with chronic renal failure and secondary hyperparathyroidism who underwent parathyroidectomy before operation underwent non-invasive image diagnosis of parathyroid glands by computed tomography (CT), scintigraphy with /sup 201/TlCl and /sup 99m/TcO/sup 4 +/, and/or ultrasonography. CT visualized 39 of 45 parathyroid glands (86.7%), weighing more than 500 mg. Scintigraphy with a subtraction method using a computer performed the diagnosis in 19 of 27 glands (70.4%). Ultrasonography detected 21 of 27 glands (77.8%). Image diagnosis was also useful in the postoperative follow-up study. The non-invasive image diagnosis of parathyroid glands in patients with chronic renal failure is thus valuable for 1) definite diagnosis of secondary hyperparathyroidism, 2) localization, and 3) diagnosis for effectiveness of conservative treatment.

International Nuclear Information System (INIS)

The reliability analysis of the Fast Flux Test Facility reactor shutdown system was reevaluated. Failure information based on five years of plant operating experience was used to verify original reliability numbers or to establish new ones. Also, system modifications made subsequent to performance of the original analysis were incorporated into the reevaluation. Reliability calculations and sensitivity analyses were performed using a commercially available spreadsheet on a personal computer. The spreadsheet was configured so that future failures could be tracked and compared with expected failures. A number of recommendations resulted from the reevaluation including both increased and decreased surveillance intervals. All recommendations were based on meeting or exceeding existing reliability goals. Considerable cost savings will be incurred upon implementation of the recommendations.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this project was to develop improved dynamic failure models for brittle materials (primarily ceramics). The approach to developing these failure models was to establish a database (ACERAM) in which fundamental material properties and processing information could be directly correlated with ballistic performance data. Under this contract, a comprehensive literature search was conducted, many contacts were established in the armor/anti-armor research and development community, and database development was undertaken. A more limited project was also undertaken to assess and compare the effects of material properties and penetration mechanisms on the ballistic performance of depleted uranium and tungsten alloy penetrators.