Energy Technology Data Exchange (ETDEWEB)

Ways of reducing the excessive energy consumption in the Polish sugar industry are examined. The three main areas where energy reduction measures might be taken are: reducing the process heat demand which arises from the need to evaporate excess water from the juice supplied to the crystallisers; improving the effectiveness of the thermal system by moving from the present four-effect evaporation to five-effect evaporation and using crystallisation vapours for juice heating; replacing old steam boilers with more efficient units. Most Polish sugar factories are relatively small, however, and the energy saving measures, all of which require the installation of more modern equipment, are not economically feasible in the short term. Moreover, the stringent limits on atmospheric emissions which come into effect in 1998 will require factories to use low-sulphur coal ...

Energy Technology Data Exchange (ETDEWEB)

The use of thermal energy in the West German sugar industry has fallen by nearly half in the last twenty years. At the same time, automation and new technologies have led to an increase in the consumption of electric energy. In many cases, the equilibrium of combined heat and power has been upset. That equilibrium is, however, a fundamental precondition of the economical energy management of a sugar factory. Electrical engineers and sugar technologists have looked at the situation in the sugar industry form different points of view and have presented interesting ideas - in some instances already put into practice - to solve the problem. Examination of the electricity consumption of alternative processes, systems and pieces of equipment used in sugar manufacturing, from the beet yard to the sugar house, has revealed marked differences and considerable potential savings. (orig.).

International Nuclear Information System (INIS)

The paper is Part 2 of the study on the thermodynamic and thermoeconomic analyses of trigeneration system with a gas-diesel engine. In Part 1, thermodynamic and thermoeconomic methodologies for such a comprehensive analysis were provided, while this paper applies the developed methodology to an actual TRIGEN system with a rated output of 6.5 MW gas-diesel engine installed in the Eskisehir Industry Estate Zone, Turkey. Energy and exergy efficiencies, equivalent electrical efficiency, the Public Utility Regulatory Policies Act (PURPA) efficiency, fuel energy saving ratio, fuel exergy saving ratio and other thermodynamic performance parameters are determined for the TRIGEN system. The efficiencies of energy, exergy, PURPA and equivalent electrical efficiency of the entire system are found to be 58.97%, 36.13%, 45.7% and 48.53%, respectively. For the whole system and its components, ...

International Nuclear Information System (INIS)

Since Taiwan lacks sufficient self-produced energy, increasing energy efficiency and energy savings are essential aspects of Taiwan's energy policy. This work summarizes the energy savings implemented by 303 firms in Taiwan's textile industry from the on-line Energy Declaration System in 2008. It was found that the total implemented energy savings amounted to 46,074 ton of oil equivalent (TOE). The energy saving was equivalent to 94,614 MWh of electricity, 23,686 kl of fuel oil and 4887 ton of fuel coal. It represented a potential reduction of 143,669 ton in carbon dioxide emissions, equivalent to the annual carbon dioxide absorption capacity of a 3848 ha plantation forest. This study summarizes energy-saving measures ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Wastenet

Secretariat of the Basel Convention United Nations Office at Geneva ...such as public utilities, waste disposal sites, large energy dependent facilities including factories, institutions (hospitals, ...it provides immediate identification of PCB wastes, informs company officials of any special handling or disposal techniques

Energy Technology Data Exchange (ETDEWEB)

Energy savings performance contracting (ESPC) is now receiving greater attention as a means of implementing large-scale energy conservation projects in housing. Opportunities for such projects exist for military housing, federally subsidized low-income housing, and planned communities (condominiums, townhomes, senior centers), to name a few. Accurate prior (to construction) estimates of the energy savings in these projects reduce risk, decrease financing costs, and help avoid post-construction disputes over performance contract baseline adjustments. This paper demonstrates an improved method of estimating energy savings before construction takes place. Using an engineering model calibrated to pre-construction energy-use data collected in the field, this method is able to predict actual energy ...

Science.gov (United States)

Most K-12 schools could save 25% of their energy costs by being smart about energy. Nationwide, the savings potential is $6 billion. While improving energy use in buildings and busses, schools are likely to create better places for teaching and learning, with better lighting, temperature control, acoustics, and air quality. This brochure, targeted to school facilities managers and business officials, describes how schools can become more energy efficient.

Energy Technology Data Exchange (ETDEWEB)

This paper uses a choice experiment to evaluate the consumers' willingness to pay for energy-saving measures in Switzerland's residential buildings. These measures include air renewal (ventilation) systems and insulation of windows and facades. Two groups of respondents consisting respectively of 163 apartment tenants and 142 house owners were asked to choose between their housing status quo and each one of the several hypothetical situations with different attributes and prices. The estimation method is based on a fixed-effects logit model. The results suggest that the benefits of the energy-saving attributes are significantly valued by the consumers. These benefits include both individual energy savings and environmental benefits as well as comfort benefits namely, thermal comfort, air quality and noise protection. (author)

British Library Electronic Table of Contents (United Kingdom)

In this article, equations of motion of a manipulator are derived after consideration of the characteristics of the driving source. By considering a collision between a link and an object, and considering the active motion to absorb the kinetic energy of the object, the trajectories for saving energy are calculated by the iterative dynamic programming (IDP) method. The dynamic characteristics of manipulator control based on the trajectory for saving energy are also analyzed theoretically and investigated experimentally.

Energy Technology Data Exchange (ETDEWEB)

The objective of the project was to provide a readily understandable and usable methodology for preliminary analysis of the economic benefit that can accrue from the use of thermal energy storage for building heating and cooling. The procedure was to be capable of providing an estimate of cooling plant and storage size, as well as the monthly savings that can be saved. The research focused on the development of a procedure for a limited class of commercial and institutional buildings in North Carolina. A simplified procedure for analyzing the potential for using thermal energy storage (TES) in such buildings in North Carolina was developed. The procedure developed consists of charts and nomographs that can be used for estimating the size of TES systems, and for estimating the monthly demand savings. The monthly demand savings can be combined with the applicable ...

Energy Technology Data Exchange (ETDEWEB)

This document provides guidance for modeling and inspecting energy-efficient property in commercial buildings for certification of the energy and power cost savings related to Section 179D of the Internal Revenue Code enacted in Section 1331 of the 2005 Energy Policy Act and noted in Internal Revenue Service Notice 2006-52. Specifically, Section 179D provides federal tax deductions for energy-efficient property related to a commercial building's envelope; interior lighting; heating, ventilating, and air conditioning; and service hot water systems.

Science.gov (United States)

... 31 5.4 FACTORIAL DESIGN STATISTICAL ANALYSIS..... ... resistance. o Factorial design statistical analysis gave the ...

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) Office of Pollution Prevention (EM-77) created is successful internally competed program to fund innovative projects based on projected returns. This is called the Return-on-Investment (ROI) program. EM-77 conducted a successful ROI pilot, developed and implemented sound management practices, and successfully transferred the program to several Operations Offices. Over the past 4 years sites have completed 262 ROI projects (costing $18.8 million) with claimed first-year savings of $88 million and claimed life cycle savings exceeding $300 million. EM-77 requested that Oak Ridge National Laboratory perform an independent evaluation of the site-led, DOE-HQ-funded pollution prevention (P2) ROI program to assist the Department in determining whether claimed savings are real.

Energy Technology Data Exchange (ETDEWEB)

In June 2009, the State of Hawaii enacted an Energy Efficiency Portfolio Standard (EEPS) with a target of 4,300 gigawatt hours (GWh) by 2030 (Hawaii 2009). Upon setting this goal, the Hawaii Clean Energy Initiative, Booz Allen Hamilton (BAH), and the National Renewable Energy Laboratory (NREL), working with select local stakeholders, partnered to execute the first key step toward attaining the EEPS goal: the creation of a high-resolution roadmap outlining key areas of potential electricity savings. This roadmap was divided into two core elements: savings from new construction and savings from existing buildings. BAH focused primarily on the existing building analysis, while NREL focused on new construction forecasting. This report presents the results of the Booz Allen Hamilton study on the existing building stock of Hawaii, along with conclusions on the key ...

Energy Technology Data Exchange (ETDEWEB)

Geothermal heat pump systems are a promising new energy technology that has shown rapid increase in usage over the past 10 years in the United States. These systems offer substantial benefits to consumers and utilities in energy (kWh) and demand (kW) savings. The purpose of this study was to determine what existing monitored data were available mainly from electric utilities on heat pump performance, energy savings, and demand reduction for residential, school, and commercial building applications. Information was developed on the status of electric utility marketing programs, barriers to market entry, incentive programs, and benefits.

International Nuclear Information System (INIS)

Energy-filtered X-ray photoemission electron microscopy (EXPEEM) is a microscopy technique which has the potential to provide surface chemical mapping during surface chemical processes on the nanometer scale. We studied the possibilities of EXPEEM using a Wien filter type energy analyzer in the high energy X-ray region above 1000 eV. We have successfully observed the EXPEEM images of Au islands on a Ta sheet using Au 3d_5_/_2 and Ta 3d_5_/_2 photoelectron peaks which were excited by 2380 eV X-rays emitted from an undulator (BL2A) at Photon Factory. Our recent efforts to improve the sensitivity of the Wien filter energy analyzer will also be discussed.

Energy Technology Data Exchange (ETDEWEB)

Preliminary results from a large-scale testbed of advanced lighting control technologies at the Phillip Burton Federal Building at 450 Golden Gate Ave. in San Francisco are presented. The first year objective of this project is to determine the sustainable energy savings and cost-effectiveness of different lighting control technologies compared to a portion of the building where only minimal controls are installed. The paper presents the analyzed results from six months of tests focused on accurately characterizing the energy savings potential of one type of daylight-linked lighting controls compared to the lighting in similar open-planned areas without dimming controls. After analyzing a half year;s data, we determined that the annual energy savings for this type of daylight- linked controls was 41% and 30% for the outer rows of lights on the South and North ...

International Nuclear Information System (INIS)

The advantages of district heating as an environmental-friendly and energy-saving technique are reviewed. The role of district heating as part of the Dutch national plan to reduce the emission of acidification and greenhouse gases by respectively 50 and 25 percent is clarified. 12 Tabs. (A.S.).

UK PubMed Central (United Kingdom)

BackgroundEvolutionary life history theory predicts that, in the absence of contraception, any enhancement of maternal condition can increase human fertility. Energetic...Full Text Available

Science.gov (United States)

In 1980 through 1982 a Basewide Energy Systems Plan (BESP) was developed under the direction of the Corps of Engineers at Ft. McClellan to assist the installation in meeting the requirements of the Army Facilities Energy Plan and the ten (10) year Energy Use Reduction Goal. Some of the energy saving projects recommended by the BESP have been implemented. In FY 1977, the total base energy consumption was 1,105,221 MBtu (Million British thermal units). By FY 1987, this had been reduced to 870,900 MBtu, a reduction of twenty-one percent (21%). This resulted in a cost avoidance for FY 1987 over base year FY 1977 of $2,960,986, or a thirty-two percent (32%) reduction.

Wastenet

... Areas of Consultation: All Areas About DECC Bioenergy Carbon capture & storage Carbon Reduction Commitment Climate Change Agreements CRC energy efficiency scheme Development, consents and planning reform Electricity Electricity network Emissions Emissions trading Energy markets Energy network Energy security Feed-in Tariffs Fuel poverty Funding and support Gas Governance Green Deal Hydroelectricity International climate change International energy Legislation Low-carbon Microgeneration News Nuclear Oil Renewable energy Saving energy and CO2 Site Wide Footer Smart ...

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy (EERE) is interested in assessing the potential economic impacts of its portfolio of subprograms on national employment and income. A special purpose version of the IMPLAN input-output model called ImBuild II is used in this study of 20 subprograms of the Weatherization and Intergovernmental Program contained in the EERE final FY 2005 budget request to the Office of Management and Budget on February 2, 2004. Energy savings, investments, and impacts on U.S. national employment and earned income are reported by subprogram for selected years to the year 2030. Energy savings and investments from these subprograms have the potential of creating a total of 228,000 jobs and about $3.1 billion in earned income (2003$) by the year 2030.

Science.gov (United States)

Marshall Hall was selected by the US Army Corps of Engineers to participate in the Energy Efficiency Analysis Program. The objective of this program is to assist military installations in identifying energy usage and cost saving projects at their facilities and possibly provide funding for projects. Entech Engineering, Inc. was selected to perform this study.

Energy Technology Data Exchange (ETDEWEB)

Versatility of the TRNSYS software program, the ease with which new components can be incorporated into the software, and its application to simulate heat pump systems was discussed. A case history was described in which the package, augmented by the addition of several recent large-scale heat pump projects, was used in calibrating a residential geothermal heat pump system at a military housing project in Fort Polk, LA. The project involved retrofitting over 4000 air source heat pumps with geothermal heat pumps in an energy savings performance contract. The calibration of the component models led to a system model which accurately predicts the performance of the geothermal heat pump. The lessons learned from the calibration exercise were used to help to predict the energy savings from one of the electric feeders at the base which serves some 200 of the 4000+ apartments. Energy ...

British Library Electronic Table of Contents (United Kingdom)

Early technical history of electric supply to electric railways is briefly reviewed as an introduction to the following seven papers included in this special issue on technologies for saving energy in railway operation. Continuous power supply played a significant role in the early history of railway technologies. The variable voltage variable frequency (VVVF) power electronic technology had also a substantial impact on railway traction systems after 1980s. VVVF technology made it possible to have more efficient drives, downsize rolling stocks, and develop regenerative brakes. Because detailed discussions on each technical development are presented in the following papers, the general remarks of those technologies made in this introduction provide logical links to the ideas presented in th...

Energy Technology Data Exchange (ETDEWEB)

The national remediation program in Croatia consists of three stages: (1) identification and characterization of radioactively contaminated sites; (2) preparing activities for restoration; and (3) physical restoration at selected (high-prioritized) sites. The program is coordinated by the APO and, in the first stage, performed by both national research institutes of Ruder Boskovi and Institute for Medical Research and Occupational Health. The program supervisors are Ministry of Health, Ministry of Economy (Department of Energy) and State Administration for Environmental Protection. There were more than thirty sites suspected to be radioactively contaminated in Croatia. They were classified into four contamination type groups: (1) dumps containing contaminated coal slag and ash; (2) dumps containing contaminated phosphates and phospho-gypsum resulting from fertilizers industry; (3) geothermal springs and gas/oil wells; and (4) sites containing natural radioactive ...

Energy Technology Data Exchange (ETDEWEB)

The goal of this project was to increase the high-temperature strength of the H-Series of cast austenitic stainless steels by 50% and the upper use temperature by 86 to 140 degrees fahrenheit (30 to 60 degrees celsius). Meeting this goal is expected to result in energy savings of 35 trillion Btu/year by 2020 and energy cost savings of approximately $230 million/year. The higher-strength H-Series cast stainless steels (HK and HP type) have applications for the production of ethylene in the chemical industry, for radiant burner tubes and transfer rolls for secondary processing of steel in the steel industry, and for many applications in the heat treating industry, including radiant burner tubes. The project was led by Duraloy Technologies, Inc., with research participation by Oak Ridge National Laboratory (ORNL) and industrial participation by a diverse group of companies.

Energy Technology Data Exchange (ETDEWEB)

This report documents the results of a six month test program of an Alternative Configuration (ACONF) power management system design for a typical United States Coast Guard (USCG) National Distress System (NDS) site. The USCG/USDOE funded work was performed at Sandia National Laboratories to evaluate the effect of a Sandia developed battery management technology known as ACONF on the performance of energy storage systems at NDS sites. This report demonstrates the savings of propane gas, and the improvement of battery performance when utilizing the new ACONF designs. The fuel savings and battery performance improvements resulting from ACONF use would be applicable to all current NDS sites in the field. The inherent savings realized when using the ACONF battery management design was found to be significant when compared to battery replacement and propane refueling at the remote NDS sites.

Energy Technology Data Exchange (ETDEWEB)

This document contains the technical proceedings of the 19 national seminar on the rational use of energy and exposition of equipment and services, organized by the Asociacion de Tecnicos y Pofesionistas en Aplicacion Energetica (ATPAE) (Association of Technicians and Professionals on Energy Application) conducted in Mexico City on September 21-25, 1998. This seminar encompassed subjects such as: energy saving in the energy sector, energy efficiency in industrial processes and practical developments, practical cases of energy saving in industry, energy saving in buildings, transportation, non-renewable energy utilization and environmental impact and eco-energies. [Espanol] Este documento contiene la memoria tecnica del 19 seminario ...

Energy Technology Data Exchange (ETDEWEB)

Thermal solar energy plants for water heating have experienced an enormous boom during the last years. Thus, a total of 200000 square metres of collector surface was installed on German rooves in 1991. This was three times as much as in the year before. And this trend of conserving natural resources by using the energy of the sun is still undiminished. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The aim was to compare the energy consumption by private and commercial vehicles with that of public transport facilities constituting urban street traffic, and to evaluate the influence of various traffic related plans such as green waves (where cars are able to drive through the town with relatively few accelerations and braking) streets with lower speed limits and special lanes and priorities for buses. The traffic pattern in four Copenhagen streets (Jagtvej, Soelvgade, Bredgade and Strandvejen) were measured and analyzed both in, and not in, the rush hour, and a special model was used to calculate the energy consumption. The model defines degree of acceleration and slow-down and speed when calculating energy consumption with regard to various driving patterns. It also calculates carbon dioxide emission. It was found that energy consumption decreased with increasing driving speed at 10-60 km/h for ...

Energy Technology Data Exchange (ETDEWEB)

Heat pumps can be installed indoors or outdoors. H. Klein investigates which site would be preferable for a one-family house. Advantages and disadvantages with regard to necessary space, noise, maintenance and repair are discussed; heat losses in both cases of installations are dealt with. Mathematic calculation shows that indoor installation is safer and more adequate in terms of energy savings.

Energy Technology Data Exchange (ETDEWEB)

The resulting emissions of the firing of ceramic products of all type are described, the factors are enumerated to diminish the emissions in the kilns and the technologies applied in the kilns to reduce these emissions while carrying out energy saving are described briefly. (author)

Science.gov (United States)

This paper focuses on a factorial-based design strategy. The approach provides an efficient and statistically reliable means for assessing the influence of multivariable effects. It is applied to the detection and evaluation of damage in impacted composite sandwich panels. The experimental results obtained from this test strategy are utilized to form an empirical response function. The resulting polynomial relates damage area to residual compression strength at values of independent variables for which testing did not occur. The response function also identifies nonlinear interaction effects of key variabes that cannot be easily ascertained by traditional single-variable test strategies. Independent variables evaluated include core thickness, number of face sheet plys and impact energy. The methodology presented allows the designer to predict with more confidence the damage tolerance of a composite material component, and the analyst to more ...

International Nuclear Information System (INIS)

Environmental targets and saving energy have become ones of the world main concerns over the last years and it will increase and become more important in a near future. The world population growth rate is the major factor contributing for the increase in global pollution and energy and water consumption. In 2005, the world population was approximately 6.5 billion and this number is expected to reach 9 billion by 2050 [United Nations, 2008. (www.un.org), accessed on July]. Water supply systems use energy for pumping water, so new strategies must be developed and implemented in order to reduce this consumption. In addition, if there is excess of hydraulic energy in a water system, some type of water power generation can be implemented. This paper presents an optimization model that determines the best hourly operation for 1 day, according to the electricity tariff, for a pumped ...

Energy Technology Data Exchange (ETDEWEB)

The industrial standard process for the purification of natural gas is to remove acid gases, mainly hydrogen sulfide and carbon dioxide, by the absorption and reaction of these gases with alkanolamines. Inadequate data for vapor -- liquid equilibrium (VLE) hinder the industry from converting operations to more energy efficient amine mixtures and conserving energy. Some energy reductions have been realized in the past decade by applying such amine systems as hindered'' amines, methyldiethanolamine (MDEA), and MDEA based amine mixtures. However, the lack of reliable and accurate fundamental VLE data impedes the commercial application of these more efficient alkanolamine systems. The first project objective is to improve the accuracy of vapor -- liquid equilibrium measurements at low hydrogen sulfide concentrations. The second project objective is to measure the VLE for amine mixtures. By improving the ...

CERN Document Server

The CKM angle $\\gamma/\\phi_{3}$ had been measured by two B-factories, the PEPII collider for the BaBar experiment and the KEKB collider for the Belle experiments. The present paper reports recent progress in $\\gamma/\\phi_{3}$.

Energy Technology Data Exchange (ETDEWEB)

There are two fundamental reasons or motivations for energy conservation: (1) economics; and (2) consideration of energy - its sources and availability. Economics speaks for itself and needs little explanation: a project is undertaken, the cost is recovered in a given period of time (we hope) and our company realizes cost savings thereafter. We study and propose a project; we estimate the payback. If approved, we implement the project. Then, we eagerly watch for its effectiveness - for the proposed payback. The second consideration in regard to energy conservation might - in the foreseeable future - become by far the most important - that of availability. Very knowledgeable persons have stated that this - in reality - is the most serious problem facing our nation today. Readily available, reasonably priced energy has given to the US the high form of living experienced today. An ...

Energy Technology Data Exchange (ETDEWEB)

Energy conservative building design has triggered greater interests in developing flexible and sophisticated air conditioning systems capable of achieving enhanced energy-savings potential without sacrificing the desired thermal comfort and indoor air quality (IAQ). This research work greatly aimed at achieving enhanced energy conservation, good thermal comfort and better IAQ for space conditioning with the application of combined variable refrigerant volume (VRV) and variable air volume (VAV) air conditioning (A/C) systems. Experimental investigation on the proposed combined air conditioning system with the application of intelligent fuzzy logic controller was performed for summer and winter climatic conditions to substantiate the energy-savings capability. The proposed system experimentally analyzed under fixed ventilation, demand controlled ventilation (DCV) and combined DCV and economizer cycle (EC) ...

International Nuclear Information System (INIS)

Magnetic properties of a recently developed Fe-based amorphous alloy with a high saturation induction of 1.65 T are reviewed. The increased saturation induction is fully utilized in transformers with reduced magnetic losses, physical sizes and audible noises, minimizing some of the drawbacks of amorphous metal-based transformers based on a currently available amorphous alloy. Impacts of this on the worldwide energy savings and reduction of greenhouse gas emissions are discussed. A recent effort in achieving a saturation induction beyond 1.65 T in nanocrystalline alloys is mentioned.

Energy Technology Data Exchange (ETDEWEB)

The manual enhances and simplifies the work of those architects and engineers whose practice includes the analysis and modification of existing buildings to reduce both fuel consumption and operating costs. A review of the principles of energy use and conservation is given. The manual also provides a step-by-step methodology for assessing and improving the year-round energy performance of buildings, as well as a series of forms, charts, and nomographs designed to serve as day-to-day tools in the energy professional's toolbox. After a cost-benefit analysis is prepared for each conservation opportunity, the owner will be able to implement decisions based on projected energy savings and calculate investment costs, operational changes, and payback periods. Each of these considerations is accorded a detailed treatment.

Energy Technology Data Exchange (ETDEWEB)

Energy and exergy studies were conducted in an orange juice manufacturing industry in Nigeria to determine the energy consumption pattern and methods of energy optimization in the company. An adaptation of the process analysis method of energy accounting was used to evaluate the energy requirement for each of the eight defined unit operations. The types of energy used in the manufacturing of orange juice were electrical, steam and manual with the respective proportions of 18.51%, 80.91% and 0.58% of the total energy. It was estimated that an average energy intensity of 1.12 MJ/kg was required for the manufacturing of orange juice. The most energy intensive operation was identified as the pasteurizer followed by packaging unit with energy intensities of 0.932 and 0.119 MJ/kg, ...

Energy Technology Data Exchange (ETDEWEB)

This paper evaluates the two well-known final waste disposal methods, incineration and landfilling. In particular we compare the social cost of two best-available technologies using a point estimate based on private and environmental cost data for the Netherlands. Not only does our comparison allow for Waste-to-Energy incineration plants but for landfills as well. The data provide support for the widespread policy preference for incineration over landfilling only if the analysis is restricted to environmental costs alone and includes savings of both energy and material recovery. Gross private costs, however, are so much higher for incineration, that landfilling is the social cost minimizing option at the margin even in a densely populated country such as the Netherlands. Furthermore, we show that our result generalizes to other European countries and probably to the USA. Implications for waste policy are discussed as well. ...

Science.gov (United States)

The advent of synfuels will require a large measurement and modeling effort of new thermodynamic and physical properties. These data are required for the economic design and operation of proposed synfuel plants. The areas of data need are well defined. The pace of measurement will be restricted by laboratory availability. The cost for the required data and for their correlation and modeling will be substantial. And finally, the cost of doing all this work will be substantial. The plants we are talking about are energy plants and synfuel plants. They are energy intensive plants, and as such, they offer the prospects for a great deal of energy saving. To do so requires good data. In those critical areas where we start hunting the energy hogs, we will find that with +-20% data those hogs are pretty well hidden.

International Nuclear Information System (INIS)

The assessment of greenhouse gas impacts in the US shows that against a baseline gasoline vehicle, the impact of including the full fuel cycle generally reduces the relative advantages of alternative transportation fuels. While a switch to diesel is estimated to save 30% as compared to gasoline, the savings from natural gas/LPG are (around 20%), for ethanol from corn (8%) and for battery electricity vehicles using power from coal (6%) are much smaller. This is largely due to the use of LCA rather than end-use comparisons. However, the results also show that there would be large savings from the use of ethanol from fuel cells using methanol (39%) or natural gas (50%), while ethanol from wood in a conventional engine appears to have the greatest savings (63%). In external costs of motor vehicle use, analysis results were presented for both air pollution and energy security impacts ...

Energy Technology Data Exchange (ETDEWEB)

In many facilities, energy management is simply a matter of managing the energy required for lighting and space conditioning. In many others, however, energy management is much more complex and involves large motors and controls, industrial insulation, complex combustion monitoring, unique steam distribution problems, significant amounts of waste heat, etc. Typical facilities offering large energy management opportunities include industrial facilities, large office and commercial operations, government institutions such as schools, hospitals and prisons. Such facilities generally have specialized industrial, commercial or institutional processes that incorporate many of the concepts covered in other chapters. These processes require thorough analytical evaluations to determine the appropriate energy-saving measures. This chapter provides some examples. In this chapter the authors ...

Energy Technology Data Exchange (ETDEWEB)

Greenhouse gas mitigation strategies are generally considered costly with world leaders often engaging in debate concerning the costs of mitigation and the distribution of these costs between different countries. In this paper, the analyses and results of the design of a 100% renewable energy system by the year 2050 are presented for a complete energy system including transport. Two short-term transition target years in the process towards this goal are analysed for 2015 and 2030. The energy systems are analysed and designed with hour-by-hour energy system analyses. The analyses reveal that implementing energy savings, renewable energy and more efficient conversion technologies can have positive socio-economic effects, create employment and potentially lead to large earnings on exports. If externalities such as health effects are included, ...

International Nuclear Information System (INIS)

In the utilization of the thermal energy by ocean temperature difference and factory waste heat, the high performance heating surfaces in pipes from which scale can be removed are required. As the method of removing scale, the method using sponge balls seems most suitable, but for applying this method, as the form of the protrusions attached to the inner surfaces of pipes, smooth circular are form is desirable. The promotion of heat transfer with the rows of circular arc protrusions like this is strongly related to the mode of flow and such structure as separation, recirculation flow, readhesion and turbulent energy generation. In this study, as the basic research to optimize the heating surface with the rows of smooth protrusions, the flow characteristics and the heat transfer characteristics including the turbulent structure of the wake of protrusions were experimentally determined, and the essence of the heat transfer ...

International Nuclear Information System (INIS)

Many governments around the world are focusing on emissions reduction through energy efficiency improvements, particularly on the demand side. Although Integrated Resource Planning (IRP), which considers both supply-side and demand-side options, had been a useful tool in the planning process for the power industry, its effectiveness has been challenged recently with the restructuring of the power sector that has occurred in China and elsewhere around the world. The paper proposes Integrated Resource Strategic Planning (IRSP) as an alternative to IRP in a deregulated power sector. IRSP takes the resource planning process one step further to the national level. In this paper, the authors demonstrate the tremendous potential for efficiency improvements on both the supply and demand sides of the power sector in China with IRSP. The results show that between 2009 and 2020, the potential for electricity savings will reach about 1228.5 TWh, and the ...

Energy Technology Data Exchange (ETDEWEB)

The short range of low-energy electrons has made them suitable for the treatment of skin lesions, especially when extensive areas must be irradiated with special considerations to save the normal underlying tissue. This report covers some salient features of total body electron irradiation: the construction of the large fields required, x-ray contamination levels, and multiple-field techniques. While the investigation is essentially experimental, we also indicate the results of calculations. We conclude most generally that treatment planning with whole skin irradiations can be as precise as with smaller fields.

Energy Technology Data Exchange (ETDEWEB)

Contents include: countermeasures to save energy of sintering plant and future plans in fukuyama works; improvement of surface quality of continuous-casting slab; development of direct quenching and tempering type HT80 steel with good weldability; numerical analysis of fluid flow in a geothermal reservoir; the finite-element calculation of turbulent flow using the universal law of the wall; development of PC 4 dual fuel engine; design of industrialized housing; Computer-aided Navigation system (CANSY); and new production control system in Fukuyama Works.

International Nuclear Information System (INIS)

Westinghouse Electric Corporation is aggressively applying cost-time management to bolster timely, cost-effective cleanup and waste management activities at sites it manages for the U.S. Department of Energy (DOE). Cost-time management is a diagnostic technique which is applicable to virtually any process. It identifies opportunities to reduce cycle-times and costs. When applied to cleanup and waste management at DOE facilities, cost-time profile analysis helps identify actions to improve productivity and quality. Moreover, by reducing cycle-times and costs, it achieves significant savings to taxpayers. (author)

Energy Technology Data Exchange (ETDEWEB)

The report presents the results of a Gas Research Institute (GRI) program to evaluate the technical and economic aspects of design options proposed by the U.S. Department of Energy (DOE) for reducing the energy consumption of residential ranges and ovens as mandated by the National Appliance Energy Conservation Act (NAECA) of 1987. The study shows that none of the proposed DOE design options are justified except electric ignition for stand-alone cooktops, based on life-cycle costs, loss of consumer utility, safety, technical considerations, or food quality considerations. An individual range uses so little gas during the year (approximately $14/year for a self-cleaning range) that it is difficult to justify any design modification, since the cost of even a simple modification could not be recovered on the basis of gas saved.

CERN Document Server

The goal of this work is to minimize the energy dissipation of embedded controllers without jeopardizing the quality of control (QoC). Taking advantage of the dynamic voltage scaling (DVS) technology, this paper develops a performance-aware power management scheme for embedded controllers with processors that allow multiple voltage levels. The periods of control tasks are adapted online with respect to the current QoC, thus facilitating additional energy reduction over standard DVS. To avoid the waste of CPU resources as a result of the discrete voltage levels, a resource reclaiming mechanism is employed to maximize the CPU utilization and also to improve the QoC. Simulations are conducted to evaluate the performance of the proposed scheme. Compared with the optimal standard DVS scheme, the proposed scheme is shown to be able to save remarkably more energy while maintaining comparable QoC.

International Nuclear Information System (INIS)

An attempt to develop a simple framework for financial evaluation of renewable energy technologies (RETs) such as photovoltaic (PV) pump, windmill pump, biogas and producer gas-driven dual fuel engine pumps for irrigation water pumping has been made. The unit cost of water and unit cost of useful energy delivered by the RETs have been estimated. The monetary benefits that accrued to the end-user have been quantified in terms of the amount of diesel or electricity saved. Financial figures of merit for the investments made in the RETs have been estimated. The effect of fuel price escalation on these measures of financial performance has also been evaluated along with the estimation of the break-even prices of fuels likely to be substituted by RETs. Results of some exemplifying calculations are presented and briefly discussed.

Energy Technology Data Exchange (ETDEWEB)

Improving software for the analysis of fenestration product energy efficiency and developing related information technology products that aid in optimizing the use of fenestration products for energy efficiency are essential steps toward ensuring that more efficient products are developed and that existing and emerging products are utilized in the applications where they will produce the greatest energy savings. Given the diversity of building types and designs and the climates in the U.S., no one fenestration product or set of properties is optimal for all applications. Future tools and procedures to analyze fenestration product energy efficiency will need to both accurately analyze fenestration product performance under a specific set of conditions and to look at whole fenestration product energy performance over the course of a yearly cycle and in the context ...

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence method with a Si/Li semiconductor detector and "2"3"8Pu exciting source was used in the study of Mn, Fe, Cu, Zn, and Pb content of solid emissions, raw and final materials of a brick factory. From the point of view of metal content, the working environment if the brick factory is safe for workers. (author) 2 refs.; 2 figs.; 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The assets that Citizen Potawatomi Nation holds were evaluated to help define the strengths and weaknesses to be used in pursuing economic prosperity. With this baseline assessment, a Planning Team will create a vision for the tribe to integrate into long-term energy and business strategies. Identification of energy efficiency devices, systems and technologies was made, and an estimation of cost benefits of the more promising ideas is submitted for possible inclusion into the final energy plan. Multiple energy resources and sources were identified and their attributes were assessed to determine the appropriateness of each. Methods of saving energy were evaluated and reported on and potential revenue-generating sources that specifically fit the tribe were identified and reported. A primary goal is to create long-term energy strategies to ...

UK PubMed Central (United Kingdom)

Trinitrotoluene (TNT) absorption was assessed in groups of workers at two explosives factories by measuring the urinary concentrations of dinitroaminotoluene (DNAT) metabolites. DNAT was detected in...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Alter both oil crisis, of 1973 and 1979, a bad effect of the elevated costs and continuously increment of the oil prices was noted, for this reason, the interest for renewable energies sources widely available in developing countries was increased. All over the world, governments have formulated main objectives for energies savings and search for friendly technologies, taking into account the effects related with the environment. The imminent scarcity of fossil fuels has made humanity the rational use of primary energies, as a result of these; new plants with improved technology have been conceived taking into account energy savings and efficiency improvement. In this context, biomass gasification technologies are important, since they consist in techniques of parallel production of electricity and heat from just one fuel. This work consists in the development ...

Energy Technology Data Exchange (ETDEWEB)

The B-Factory which is constructed by National Laboratory for High Energy Physics is the device for elucidating the breakdown of symmetry of matter and antimatter by studying the behavior of B mesons which are generated in large quantity when the electrons and the positrons which are accelerated to light velocity level are collided. In order to maintain electron beam-positron beam bunch circling the ring at light velocity stably, the instability of the coupled bunch must be overcome. For this purpose, the ultrahigh speed beam position digital feedback control system was developed. This system is composed of the high speed input-output substrate using GaAs LSI, the feedback computation substrate using complementary metal oxide semiconductor and the memory mounted on it, and the real time operation device. The development of both substrates and their functions are explained. The real time data collection and the change of computation parameters ...

International Nuclear Information System (INIS)

The production methods for seven radioisotopes, Ga-67, Sr-85, Pd-103, In-111, Tu-167, Hg-197 and Pb-203, by using a classical 1.5m cyclotron in the Institute of Physics and Power Engineering, Obninsk, USSR, are described. At present, more than 50 cyclotrons in different countries are used for the production of radioisotopes applied to medicine. Radioisotopes are produced with the cyclotron in the I.Ph.P.E. in the form of irradiated targets, which are delivered to Moscow radiopharmaceutical factory, where radiopharmaceuticals are produced on the base of these targets. The cyclotron is operated in two regimes providing the acceleration of protons, deuterons and alpha -particles. Two types of target assemblies are used for irradiation, the one is intended for the internal beam, and the other is for the external beam. The reactions used for the production of seven radioisotopes described above, the types of targets, particle energy, respective ...

International Nuclear Information System (INIS)

Natural gas is essential to the world economy. Gas now accounts for almost a quarter of OECD primary energy requirements and is expected to become the second most important fuel in the world in the next decade. Industrial and residential consumers increasingly rely on natural gas to keep their houses warm, their lights on and their factories running. Meanwhile the gas industry itself has entered a new phase. Where gas used to be restricted to regional markets, it is now increasingly traded on a global scale. While gas production and transport requires long-term investment, now it is optimised on a short-term basis. Demand continues to grow, but local gas production has become much more expensive. How should we react? How will demand be satisfied? What changes are required to promote flexibility and trade? What are the implications for gas security, investment and interdependence? At stake is an opportunity to diversify supply and demand - but ...

Energy Technology Data Exchange (ETDEWEB)

In robotics inverse dynamics is a standard control concept for highly nonlinear multibody systems. It is shown, however, that inverse dynamics results in a high energy demand. Therefore, linear energy efficient state feedback controllers are designed in a way that a performance index representing the energy consumption is minimized. At the same time inequality constraints such as control error and limited input variables have to be met. For the control design an analytical solution by pole placement is presented as well as a numerical controller optimization. This control design includes small motions in the neighborhood of the operating point. Then, linear controllers are tested with respect to control error and energy consumption when undergoing large displacement motion. It is shown that linear state feedback can only save energy if large control errors are ...

Energy Technology Data Exchange (ETDEWEB)

The situation of natural gas in the Federal Republic of Germany is described, with particular emphasis on the advantages and consequences of natural gas supply. The brochure discusses the role of natural gas on the energy market, the reliability of natural gas supply, the environmental impacts, the energy-saving effect of natural gas, natural gas prices, the competitive strength of the German gas industry, and the long-term reliability of natural gas supply. (orig.) [German] Die Situation des Erdgases in der Bundesrepublik Deutschland wird beschrieben, wobei die wichtigsten Vorteile und Auswirkungen der Erdgasversorgung besonders hervorgehoben werden. Es geht um die Stellung des Erdgases im Energiemarkt, die Sicherheit der Energieversorgung, Umweltschutz, Energieeinsparung durch Erdgaseinsatz, Erdgaspreise, Leistungsfaehigkeit der deutschen Gaswirtschaft und um die langfristig gesicherte Erdgasversorgung. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The energy cost of compressors accounts for up to 90% of the total cost. Oil-free compressors could reduce the cost almost by half, i.e. annual savings of 112,500 DM would be achievable. [German] Ueber die Gesamtlaufzeit betrachtet, machen die Energiekosten bei Verdichtern bis zu 90% der Gesamtkosten aus. Deshalb muss bei der Auswahl von Kompressoren dem Energieverbrauch besondere Aufmerksamkeit geschenkt werden. Mit oelfreien Kolbenkompressoren liessen sich in einem speziellen Fall die Kosten fast halbieren, was jaehrlichen Einsparungen von 112 500 DM entspricht. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A number of buildings dating from the 1950s and 1960s were retrofitted with thermal insulation in order to cut energy consumption. This took place within the building competition 'Therma' nitrated by the Federal Ministry of Regional Planning, Building and Town Planning in 1974. Result at that time were so encouraging that now, 15 years later the results were checked again with special attention to the long-term performance of the thermal insulation measures. Laboratory tests prove that the building materials are still in good condition and that humidity has not increased with age. Cracks in the surface plaster of the compound insulation systems occurred at different frequencies and intensities and usually caused by thermal tensions. (BWI).

British Library Electronic Table of Contents (United Kingdom)

In this paper, the performance of customer-owned distributed generation (DG) units is quantified from different perspectives through an uncertainty study. A Monte Carlo-based method is applied to assess the stochastic operation of the customer-owned DG units in the power distribution system. Several cases are studied to analyze the impact on system performance of using such generators, with the emphasis on benefits. The results of the studied cases show that proper operation of customer-owned DG units placed close to significant consumption centers offers several benefits which lead to significant energy savings and improvement in the performance indices while maintaining the cost-effectiveness. Furthermore, based on the energy demand, different electricity price scenarios considering a co...

Science.gov (United States)

This final scientific report documents the Industrial Technology Program (ITP) Stage 2 Concept Development effort on Data Center Energy Reduction and Management Through Real-Time Optimal Control (RTOC). Society is becoming increasingly dependent on information technology systems, driving exponential growth in demand for data center processing and an insatiable appetite for energy. David Raths noted, 'A 50,000-square-foot data center uses approximately 4 megawatts of power, or the equivalent of 57 barrels of oil a day1.' The problem has become so severe that in some cases, users are giving up raw performance for a better balance between performance and energy efficiency. Historically, power systems for data centers were crudely sized to meet maximum demand. Since many servers operate at 60%-90% of maximum power while only utilizing an average of 5% to 15% of their capability, there are huge inefficiencies ...

DEFF Research Database (Denmark)

The objective of the present study was to test the hypothesis that circulating levels of insulin-like growth factor-I (IGF-I) are inversely associated with inflammatory processes in an elderly background population.

Energy Technology Data Exchange (ETDEWEB)

The goal of this program was to increase the high-temperature strength of the H-Series of cast austenitic stainless steels by 50% and upper use temperature by 86 to 140 F (30 to 60 C). Meeting this goal is expected to result in energy savings of 38 trillion Btu/year by 2020 and energy cost savings of $185 million/year. The higher strength H-Series of cast stainless steels (HK and HP type) have applications for the production of ethylene in the chemical industry, for radiant burner tubes and transfer rolls for secondary processing of steel in the steel industry, and for many applications in the heat-treating industry. The project was led by Duraloy Technologies, Inc. with research participation by the Oak Ridge National Laboratory (ORNL) and industrial participation by a diverse group of companies. Energy Industries of Ohio (EIO) was also a partner in this project. Each team partner ...

Energy Technology Data Exchange (ETDEWEB)

Using an economic perspective, it is possible to make a case for green buildings and green development practices by placing emphasis on Energy Efficiency and Environmental Design. Several case studies have demonstrated that green buildings save money through reduced consumption of natural resources, electricity and gas both at the building site and at the source of energy. Sound environmental practices and energy efficiency measures improve the environmental conditions throughout the state by reducing power plant emissions and reducing operations and maintenance budgets in the state. The author presented a case study where a green development project was guided and monitored using the Environmental Performance Rating System called Leadership in Energy and Environmental Design (LEED), version 2.0. The work was registered to achieve LEED certification. A brief study on current ...

International Nuclear Information System (INIS)

High and volatile natural gas prices have increasingly led to calls for investments in renewable energy. One line of argument is that deployment of these resources may lead to reductions in the demand for and price of natural gas. Many recent US-based modeling studies have demonstrated that this effect could provide significant consumer savings. In this article we evaluate these studies, and benchmark their findings against economic theory, other modeling results, and a limited empirical literature. We find that many uncertainties remain regarding the absolute magnitude of this effect, and that the reduction in natural gas prices may not represent an increase in aggregate economic wealth. Nonetheless, we conclude that many of the studies of the impact of renewable energy on natural gas prices appear to have represented this effect within reason, given current knowledge. These studies specifically suggest that a 1% reduction ...

Energy Technology Data Exchange (ETDEWEB)

During the first phase of this project, significant progress was made in several of the connected issues that make up the objectives of this grant. The central thrust or theme of this work under the DOE/ERIP grant is to carry out prototype testing of the concept of tribopolymerization as a novel mechanism of boundary lubrication--under more severe, high-load, high-speed conditions that are most likely to exist in field applications. The authors see this as an important step in attracting industries to license and market the results of this new technology. In addition, they have began to explore other potential, energy-saving applications of the concept of tribopolymerization. These exploratory studies are quite promising; they are likely to open new doors in industrial applications. To carry out the experimental part of this program, a new device has been built. Highlights of these and other developments are given.

Energy Technology Data Exchange (ETDEWEB)

An experiment lasting a number of hours was carried out with 6 men under standardised climate chamber conditions to find out to what extent wallpaper that reflects about 65-75% in the infra-red range by comparison with normal wallpaper that reflect only 3-5% of heat, has measurable positive effects on the thermoregulation of the human body and the human sensation of temperature. The measurements of skin temperature and heat flow intensity in the deeper areas of the body and the periphery, and metabolic heat conversion measurements (indirect calorimetry) confirm that infra-red reflection of the heat irradiated from the body lead to a measurable heat recovery on the body surface with a reduction of metabolic conversion. It was proved that it is possible to reduce the average room temperature by up to 4 K whilst maintaining the same degree of thermal comfort, which corresponds to a 20% saving in heating energy. (orig./BWI).

Energy Technology Data Exchange (ETDEWEB)

A new interest in magnesium alloys has arisen since light-weight constructions have become more and more attractive. Products that are currently available are mostly cast, forged, and extruded. A cost-effective production of sheet metals will render new perspectives in the design of light-weight constructions. The development of new casting technologies like thin slab casting or strip casting with an in-line rolling process is expected to result in a shorter processing time featuring a high potential of saving energy, time, and cost. Particular attention is paid to the casting process parameters such as casting speed and solidification speed. This article deals with some aspects of a magnesium-adapted single-belt caster. Results of casting experiments and material examination are shown as well as some advices given concerning safety and handling of liquid magnesium. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The ventilation requirements for decontamination are normally determined with a static calculation method. In some cases, the pollutant emission is intermittent, for example in the car park of an office building, where all the cars enter and leave the place nearly at the same time. Generally, in such a case, the volume of the garage is large, consequently the time constant of the system has a high value. So a static approach would no longer stay accurate and a dynamic evaluation is needed. With the help of some assumptions, calculations remain rather simple and results can be plotted on nomographs or computed on a programmable handheld calculator. The amount of energy saved may appear very large in some cases. A sizing optimization will be required but also remains easy to compute. The paper presents the method of calculation for a single ventilation level and the optimization of a two-level ventilation.

Energy Technology Data Exchange (ETDEWEB)

Hybrid vehicles have two power supplies as engine and electric motor which are used most efficiently corresponding to objects respectively to attain energy-saving and low pollution. In this paper, factors concerning the fuel economy of hybrid vehicles and potential thereof are examined, and the possibility of reducing fuel cost by half is described. As possible modes of highly efficient hybrid vehicles, series hybrid vehicles (SHEV) of conventional internal combustion engine, parallel hybrid vehicles using EV in combination, series-parallel hybrid vehicles (SPHV), series type fuel cell type vehicles, ceramic engine-turbo compound power generating SPHV as well as SHEV, and ceramics gas turbine engine power generating SHEV are mentioned. 10 refs., 14 figs.

Energy Technology Data Exchange (ETDEWEB)

The main aim of the project is to model the energy wood business and total logistics in a certain large region. First, wood utilisation locations inside this area are examined; the most important ones are the wood processing factories, and the heating- and power plants. After that, wood potentials in the forests of the area are evaluated in sub-areas suitable in size and sufficiently detailed for further evaluations. For that purpose, the most valuable source data are forest management plans, up to ten years forward, on which basis the wood fuel potentials can be evaluated following sustainable development. In Finland there are extensive and detailed data bases storing forest information and it is possible to collect necessary data for a data base applicable to our calculations. In logistical sense it is important to know, by which delivery chains the economically best and desired results are achieved. The software prototype based on data base ...

Energy Technology Data Exchange (ETDEWEB)

The hospitals are important consumers of energy. At the General Hospital of Zone (HGZ) N of the IMSS in Aguscalientes (HGZ N . IMSS Ags.), the diesel oil is the main fuel that is used to satisfy the requirements of thermal energy of the hospital. According to the data collected by this author, this fuel represented in 2001, 75% of its total energy consumption and the 67.9% of its total costs in energy that ascended to $396.131 (December 2001 Dollars) Since this last amount represents an important percentage of the total expenses of the hospital (29.367 million dollars) it is important to determine the technical-economic possibilities of thermal energy saving of the hospital. The HGZ N 1 IMSS Ags. is located in a ampler conglomerate where the IMSS units are located, such as, the regional laundry, the sport unit, the center of social security, the familiar ...

International Nuclear Information System (INIS)

This paper reviews three key initiatives undertaken in the historical city of Oxford to bring about reductions in energy-related CO_2 emissions on a city-wide scale. The author has been part of all the three initiatives. In 2002, a collaborative partnership between academia, industry and city council started the Oxford Solar Initiative (OSI) which uses a community-based approach to help households and organisations in Oxford, financially and technically, to install solar energy systems and energy efficiency measures in buildings. So far OSI has facilitated the installation of 80 active solar systems, over 450 energy efficiency measures and 3,000 low energy bulbs. The scientific basis of OSI is a GIS-based DECoRuM model which estimates and maps baseline energy use and CO_2 emissions on a house-by house level, identifies 'pollution' hotspots, predicts the ...

Energy Technology Data Exchange (ETDEWEB)

This study estimated energy, environmental and consumer economic impacts of U.S. Federal residential energy efficiency standards that became effective in the 1988-2001 period or will take effect by the end of 2007. These standards have been the subject of in-depth analyses conducted as part of DOE's standards rulemaking process. This study drew on those analyses, but updated certain data and developed a common framework and assumptions for all of the products. We estimate that the considered standards will reduce residential primary energy consumption and CO{sub 2} emissions in 2020 by 8-9% compared to the levels expected without any standards. They will save a cumulative total of 25-30 quads by the year 2015, and 60 quads by 2030. The estimated cumulative net present value of consumer benefit amounts to nearly $80 billion by 2015, and grows to $130 billion by 2030. The overall benefit/cost ...

Energy Technology Data Exchange (ETDEWEB)

Fact sheet on an analysis system for dyebath processes in the carpet manufacturing industry written for the NICE3 Program. The Georgia Institute of Technology (G.I.T.) has developed an effective automated dyebath analysis and reuse system that improves the energy, environmental, and economic performance of dyehouse batch operations. The new system enables dyeing solutions to be accurately monitored and adjusted for reuse. According to industry estimates, 160 pounds of water are used to produce each pound of textile product. The current wasteful batch dyeing process requires all water and residual chemicals, as well as the energy required to heat the mixture for dyeing, to be dumped after one application. Spent dyebaths can only be reused after they are sampled, analyzed, and reconstituted, a process requiring labor and expertise that are unavailable in the dyehouses. Therefore, successful commercial reuse depends on an automated analysis system ...

Energy Technology Data Exchange (ETDEWEB)

This technical report describes an outline, features, total energy efficiency, and specifications of binary heat pump system. A closed circuit distributed water heat source heat pump method is employed in the binary heat pump system. Since the circulating water, which is adjusted at a constant temperature, is used as the heat source of the indoor unit, a stable performance can be obtained regardless of outside atmospheric temperature. The binary heat pump system is mainly composed of a center heat pump unit, indoor heat pump unit, heat source water pipes, and circulating pump. The center heat pump unit and the indoor heat pump unit are connected with each other by the heat source water, and each unit can be operated independently. This system is characterized by the simultaneous operation of cooling and heating, high efficiency, high energy saving, high reliability of system, excellent environmental acceptability, etc. The ...

Energy Technology Data Exchange (ETDEWEB)

Interest in renewable and clean energies such as hydrogen has increased because of the high level of polluting emissions, increasing costs associated with petroleum and the escalating problems of global climate change. In the presence of a light source, a microbial photosynthetic process provides a system for the conversion of some organic compounds into biomass and hydrogen. Using Rhodopseudomonas palustris as a cell-factory, hydrogen photo-evolution was investigated in a photobioreactor (PBR) irradiated either from one or two opposite sides. Irradiating the photobioreactor from only one side, in the presence of malic acid, a reactor hydrogen production of 2.786 l(H{sub 2}) PBR{sup -1} was achieved. When the PBR was irradiated from two opposite sides, hydrogen photo-evolution increased to 3.162 l(H{sub 2}) PBR{sup -1}. Experiments were carried out using inoculum from either the retardation or the exponential growth phases. Using the latter, ...

UK PubMed Central (United Kingdom)

Statistical design of experiments is widely used among scientists and engineers to understand influential factors in a laboratory or manufacturing process. One of the underlying principles of...Full Text Available

Science.gov (United States)

This book describes one approach to building and operating biogas systems. The biogas systems include raw material preparation, digesters, separate gas storage tanks, use of the gas to run engines, and the use of the sludge as fertilizer. Chapters included are: (1) "Introduction"; (2) "Biogas Systems are Small Factories"; (3) "The Raw Materials of Biogas Digestion"; (4) "The Daily Operation of a Biogas Factory"; (5) "The Once a Year Cleaning of the Digester"; (6) "Tanks and Pipes: Storing and Moving Biogas"; (7) "The Factory's Products: Biogas"; (8) "The Factory's Products: Biofertilizer"; (9) "The ABCs of Safety"; and (10) "Conclusion: Profiting from an Appropriate Technology." Many diagrams are provided throughout this handbook. New ideas, composting, bioinsecticides, ferrocement, facts and figures, sources and resources, feasibility studies, problem solving, and vocabulary are presented in the ...

Science.gov (United States)

The effect of spatial auditory information on a listener's ability to detect, identify, and monitor multiple simultaneous speech signals was evaluated using virtual audio technology. Factorial combinations of three variables - the number of localized spee...

Wastenet

...Year nine students will be taught the importance of mateship in a bid to reduce risky behaviour and save lives as part of a school-based intervention program to be introduced in Queensland. 24.11.10 Safe sex saves schoolies from chlamydia The safe-sex message is failing to get ...

Energy Technology Data Exchange (ETDEWEB)

The extensive research and development effort was initiated by the U.S. Department of Energy (DOE) in 2002 at West Virginia University (WVU) in order to investigate practical ways of reducing the structural weight and increasing the durability of heavy vehicles through the judicious use of lightweight composite materials. While this project was initially focused on specific Metal Matrix Composite (MMC) material, namely Aluminum/Silicon Carbide (Al/SiC) commercially referenced as ''LANXIDE'', the current research effort was expanded from the component level to the system level and from MMC to other composite material systems. Broadening the scope of this research is warranted not only by the structural and economical deficiencies of the ''LANXIDE'' MMC material, but also by the strong coupling that exists between the material and the geometric characteristics of the structure. Such coupling ...

Science.gov (United States)

Newly commercialized Fourier transform Raman spectroscopic instrumentation provides a simpler alternative for vibrational spectroscopic analysis. Instrument vendors currently design for laboratory use, but there are many potential process applications of these stable, easy to use instruments. Raman spectroscopy is highly suited to analysis of aqueous samples. Near infrared excitation minimized fluorescence interference and allows for remote operation via fiber optic probes. The Department of Energy has funded research at the Measurement and Control Center to establish the utility of this method for on-line composition analysis in distillation columns. Laboratory evaluation and instrument employs an air-cooled laser and a thermoelectrically cooled detector. The device is mounted on a three by foot cart for convenient location in control rooms. Current fiber optic extension cables allow for analysis in a cell thirty five meters from the instrument. Application of the ...

Energy Technology Data Exchange (ETDEWEB)

Panel cooling of buildings offers energy savings over conventional space-cooling systems. We present a procedure for calculating the performance of H[sub 2]O-LiBr absorption-panel cooling systems, in which the evaporator is the panel itself. Nomographs have been developed for this approach. Under the conditions examined, the H[sub 2]O-LiBr absorption unit operates with a theoretical performance coefficient of about 90% and with a practically constant specific cooling capacity of 2394 kJ/kg H[sub 2]O. For common values of the parameters involved, the panel cooling power varies from 25 to 175 W/m[sup 2] and the cooling water mass-flow through the panel is 40-260 g/m[sup 2]h. The thermal power needed to drive the system varies from 27 to 200 W/m[sup 2] and the associated temperatures from 70 to 100[sup o]C; thus, the system may be operated on solar energy. (Author).

Energy Technology Data Exchange (ETDEWEB)

The industrial policy of fine ceramics which is one of the new material expected to solve energy/environmental problem, is described. Fine ceramics are possessed with the characteristics like surpassing electromagnetic properties, heat resistance, high strength, etc. and its use as highly efficient power generation plant material, functional material for various sensors/electronic, and activation of existing industries are cited. As for the reclamation of global environment, promotion of saving energy in a global scale, development of innovative environmental technology and increase of carbon dioxide absorption source are described. Furthermore, research and development work in Japan on global environmental industrial technology for 1992 to 1993, new sunshine project and technical developments relating to fine ceramics are explained. As for the results of research and development, the results from the case study of 300kw ...

Energy Technology Data Exchange (ETDEWEB)

By joining the `climate association of European cities`, Frankfurt has agreed to reduce its CO{sub 2}-emissions by 50% by the year 2010. The so-called `climate offense 1991` was the first regulatory paper to be set up by a community to reach this goal over a long term. This report now represents the present level of the project. Main points are the development of houses with low entropy, the retrofitting of heating systems, water saving measures and energy management. (BWI) [Deutsch] Durch den Beitritt zum `Klima-Buendnis der Europaeischen Staedte` hat sich die Stadt Frankfurt/M. verpflichtet, die CO{sub 2}-Emissionen bis zum Jahr 2010 um 50% zu senken. Mit der sog. `Klimaoffensive 1991` wurde dann erstmals von einer Kommune in Deutschland ein detailliertes Regelwerk aufgestellt, um dieses Ziel langfristig erreichen zu koennen. Der vorliegende Bericht stellt den aktuellen Stand des Projektes dar. Kernpunkte sind die Entwicklung von ...

Energy Technology Data Exchange (ETDEWEB)

The conservation of energy through the use of the optimum economic thickness of insulation has clear benefits for industry in the U.S. Potential energy savings have been estimated to be the equivalent of 250 million of barrels of oil per year over the next decade. As is the case with any capital expenditure, the dollars spent for insulation must be expected to provide the plant owner with a certain return on his investment. This manual provides data and guidelines for estimating dollar costs and insulation life which enable the user to specify the least-cost insulation thickness based on minimum life cycle cost and required percentage return on investment. A large degree of design flexibility is provided for, so that specific economic and design criteria may be taken into account. A number of useful working aids are provided, including sample problems, forms and worksheets, and nomographs which may be used to simplify ...

Energy Technology Data Exchange (ETDEWEB)

Air flow and the buoyancy-driven flow through a building`s horizontal openings was discussed. Horizontal openings occur in staircases, stairwells, ventilation shafts and chimneys. Mass and energy transfer through them have important implications regarding energy saving, thermal comfort, control of contaminants and micro-organisms and spread of fire and smoke. The analysis of the buoyancy-driven flow was attained using computational fluid dynamics (CFD). Use was made of the CFD code FLUENT which integrated the Navier-Stokes equations by a time-dependent, finite volume method. Good agreement was achieved between predicted and experimental measurements of flow rate. Results showed that flow patterns in horizontal openings were transient and unstable. The air exchange through the openings occurred in intermittent pulses. The flow rate through the opening increased with the temperature difference between zones in buildings and ...

Energy Technology Data Exchange (ETDEWEB)

Energy storage can be a cost-effective component of hybrid remote power systems. Storage serves the special role of taking advantage of intermittent renewable power sources. Traditionally this role has been played by lead-acid batteries, which have high life-cycle costs and pose special disposal problems. Hydrogen or zinc-air storage technologies can reduce life-cycle costs and environmental impacts. Using projected data for advanced energy storage technologies, LLNL ran an optimization for a hypothetical Arctic community with a reasonable wind resource (average wind speed 8 m/s). These simulations showed the life-cycle annualized cost of the total energy system (electric plus space heating) might be reduced by nearly 40% simply by adding wind power to the diesel system. An additional 20 to 40% of the wind-diesel cost might be saved by adding hydrogen storage or zinc-air fuel cells to the system. ...

Energy Technology Data Exchange (ETDEWEB)

ORNL has conducted a Nuclear Power Options Viability Study for the Department of Energy. That study is primarily concerned with new technology which could be developed for initial operation in the 2000 to 2010 time frame. Such technology would have to compete not only with coal options but with incrementally improved commercial light-water-reactors. This survey reported here was undertaken to gain an understanding of the nuclear commercial technology likely to be offered in the late 1980s and perhaps beyond. The three US vendors actively marketing NSSSs are each developing a product for the future which they expect to be more reliable, more maintainable, more economical, and safer than the present plants. These are all essentially 3800-MW(t) designs, although all are studying smaller plants. They apparently will be off offered as standard prelicensed designs with much larger scope than earlier NSSS offerings, with the possibility of firm prices. Westinghouse with ...

Energy Technology Data Exchange (ETDEWEB)

''Intelligent Extruder'' described in this report is a software system and associated support services for monitoring and control of compounding extruders to improve material quality, reduce waste and energy use, with minimal addition of new sensors or changes to the factory floor system components. Emphasis is on process improvements to the mixing, melting and de-volatilization of base resins, fillers, pigments, fire retardants and other additives in the :finishing'' stage of high value added engineering polymer materials. While GE Plastics materials were used for experimental studies throughout the program, the concepts and principles are broadly applicable to other manufacturers materials. The project involved a joint collaboration among GE Global Research, GE Industrial Systems and Coperion Werner & Pleiderer, USA, a major manufacturer of compounding equipment. Scope of the program ...

Energy Technology Data Exchange (ETDEWEB)

Oestfold Research has trough the project 'Climate accounts for disposal' for Waste Norway developed a model for calculation of net greenhouse gas emissions at the disposal of various waste types. The model is based on life cycle methodology according to the standard IS014044. This model has been used for plastic packaging in the project by adapting the basic values of specific conditions in the municipality of Fredrikstad. Oestfold Research has made an assessment of greenhouse gas emissions for the recycling and material recovery of plastic packaging from households in the district on assignment from Fredrikstad municipality and compared with the current solution where plastic packaging together with residual waste is used for energy utilisation. Based on the population in Fredrikstad and estimated amount of plastic packaging waste arising per household per year the difference in climate impact was analyzed and these scenarios calculated: ...

Energy Technology Data Exchange (ETDEWEB)

The aim of the study was to establish by means of a measuring programme how much energy for space heating can be saved by the installed hybrid system. Further, experience with the systems was to be gathered under practical use conditions. As user behaviour can influence space heating energy consumption to an extent having several times the effect of the contribution of the hybrid system, a fact that is also reported in literature, it is not sufficient to measure only space heating energy consumption. So, a unit in one of the terraced houses was scrupulously measured. In the three other terraced houses, only space heating energy consumption was measured.- This final report contains not only a description of the concepts of the buildings and hybrid system but also the energy consumptions measured, and detailed analyses of the budgets. (orig./AKF) [Deutsch] Mit ...

International Nuclear Information System (INIS)

subsequent to its in-reactor dwell time, spent fuel still contains large amounts of materials that are recoverable, for value-added energy purposes (uranium, plutonium), together with fission products, and minor actinides, making up the residues from nuclear reactions. The treatment and recycling of spent nuclear fuel, as implemented in France, entail that such materials be chemically partitioned. The development of the process involved, and its deployment on an industrial scale stand as a high achievement of French science, and technology. Treatment and recycling allow both a satisfactory management of nuclear waste to be implemented, and substantial savings, in terms of fissile material. Bolstered of late as it has been, due to spectacularly skyrocketing uranium prices, this strategy is bound to become indispensable, with the advent of the next generation of fast reactors. This Monograph surveys the chemical process used for spent fuel ...

Science.gov (United States)

TART97 is a coupled neutron-photon, 3 dimensional, combinatorial geometry, time dependent Monte Carlo transport code. This code can run on any modern computer. It is a complete system to assist you with input preparation, running Monte Carlo calculations, and analysis of output results. TART97 is also incredibly fast: if you have used similar codes, you will be amazed at how fast this code is compared to other similar codes. Use of the entire system can save you a great deal of time and energy. TART 97 is distributed on CD. This CD contains on-line documentation for all codes included in the system, the codes configured to run on a variety of computers, and many example problems that you can use to familiarize yourself with the system. TART97 completely supersedes all older versions of TART, and it is strongly recommended that users only use the most recent version of TART97 and ist data files.

Energy Technology Data Exchange (ETDEWEB)

Industrial utilization of reaction mechanisms of microorganisms under anaerobic condition permits structuring energy saving type production processes. The present survey has investigated features of new microorganisms under anaerobic condition and the status of researches thereon inside and outside the country, and discussed their future applications. Chapter 1 compares anaerobic microorganisms and functions of microorganism under anaerobic condition with those aerobic to describe their general features, and describes the purpose of this survey and the summary of the investigations. Chapter 2 surveys the current status of technologies to utilize microorganisms under anaerobic condition. Chapter 3 outlines metabolic characteristics of the anaerobic microorganisms, and extracts functions effective for material production by different anaerobic microorganisms to describe their applicability. Chapter 4 evaluates the system classification for the ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this study was to assess the feasibility for propane as an automotive fuel in Manitoba, by comparing the overall performance and operating costs of a test fleet operating on propane with that of a control fleet operating on unleaded gasoline. The performance of gasoline and propane was compared by using two specific tests: general driveability and relative fleet fuel consumption were determined by driver surveys and gross fuel use data from normal urban and rural vehicle operation. Specific fuel consumption was determined by controlled chassis dynamometer tests on a series of selected vehicles utilizing representative driving cycles. Fleet drivers operating propane fueled vehicles were satisfied with vehicle operation and reported similar vehicle performance with either gasoline or propane. Although there was no significant difference in specific fuel consumption, the specific energy consumption of similar vehicles was lower when operated on ...

Energy Technology Data Exchange (ETDEWEB)

An almost primordial trend in the conversion and use of energy is an increased complexity and cost of conversion systems designed to utilize cheaper and more-abundant fuels; this trend is exemplified by the progression fossil fission {yields} fusion. The present projections of the latter indicate that capital costs of the fusion ``burner`` far exceed any commensurate savings associated with the cheapest and most-abundant of fuels. These projections suggest competitive fusion power only if internal costs associate with the use of fossil or fission fuels emerge to make them either uneconomic, unacceptable, or both with respect to expensive fusion systems. This ``implementation-by-default`` plan for fusion is re-examined by identifying in general terms fusion power-plant embodiments that might compete favorably under conditions where internal costs (both economic and environmental) of fossil and/or fission are not as great as is needed to justify ...

Energy Technology Data Exchange (ETDEWEB)

The unit cost of energy production of wind generators is examined by means of a model of the turbine power curve and the Weibull model of wind probability function, by applying the usual economic equations. The analysis is carried out in terms of dimensionless variables whose range of variability is defined by examining the data of 80 modern commercial wind turbines; likewise, the economic parameters are based on the present state of costs. The unit cost decreases asymptotically when alpha (ratio between mean wind speed and cut-in speed) - increases and shows a lower limit of 2 to 5 Ecent/kWh. This cost depends both on the value of the machine parameter {phi} (ratio between nominal and cut-in speed) and on the basic prices. The effect of the Weibull shape parameter kappa is different according to the values of {alpha} and {phi}: with low {alpha} and high {phi} the unit cost increases along with {kappa} (that is with the regularity of the winds); the more {alpha} ...

Energy Technology Data Exchange (ETDEWEB)

The University of Georgia, in collaboration with GE Global Research, has investigated the relevant quenching mechanism of phosphor coatings used in white light devices based on UV LEDs. The final goal of the project was the design and fabrication of a high-efficacy white light UV-LED device through improved geometry and optimized phosphor coatings. At the end of the research period, which was extended to seamlessly carry over the research to a follow-up program, we have demonstrated a two-fold improvement in the conversion efficiency of a white light LED device, where the increase efficacy is due to both improved phosphor quantum efficiency and lamp geometry. Working prototypes have been displayed at DOE sponsored meetings and during the final presentation at the DOE Headquarters in Washington, DC. During the first phase of the project, a fundamental understanding of quenching processes in UV-LEDs was obtained, and the relationships that describe the performance of the phosphor as a ...

Energy Technology Data Exchange (ETDEWEB)

This official IEA report is a deliverable of IEA SHC Task 21/IEA BCS Annex 29: Daylight in Buildings. The Task focuses on daylighting systems and strategies which can be applied in new and existing buildings with a high potential electricity saving potential such as offices, schools, commercial, and institutional buildings. The daylighting performance of these strategies and systems is tested in laboratory facilities, through modeling, and in real case study buildings. This paper provides methods and procedures to evaluate the daylighting performance of real buildings. Annex 29 case studies located in Europe, North America, and Australia. It is a deliverable of Subtask D research projects. The main objective of Subtask D, as stated in the Implementing Agreement of Task 21/Annex 29, is `to demonstrate the viability of daylighting buildings in various world climatic zones as a means of achieving significant improvements in building energy ...

Energy Technology Data Exchange (ETDEWEB)

A thermal and economic study, carried on by using the first and second law of thermodynamics concepts demonstrated the economic feasibility of the cogeneration system, and proposed modifications to be done in the studied cryogenic plant, a typical T-240 NA MPL3 plant. The thermodynamic analysis showed that the second law efficiency of the processes could be improved, together with a 12% electric energy consumption reduction. Four cogeneration schemes were analyzed with both the first and second laws of thermodynamics and, then, the economic analysis was performed. Rankine, Brayton, Otto and Combined gas-steam basic cycles were used in this analysis.The combined gas-steam cycle was shown to be more economically feasible than others. Thermal and electric loads were well balanced, resulting in a higher second law efficiency. Although the initial investment for the modification was higher, the savings resulted to be higher, turning into a higher ...

International Nuclear Information System (INIS)

Small economies such as New Zealand risk significant economic hardship without careful evaluation of alternatives to petroleum-based transportation due to the adverse effects of climate change and depleting international oil reserves. This paper uses an integrated multi-regional multi-fleet system dynamics model of New Zealand's energy economy to assess the primary impacts of alternative vehicle fleet technologies. Results suggest that hydrogen fuelled HICEs and FCVs may offer significantly greater economic savings than BEVs due to a much lower capital cost. Under our Base Case, 65% of the light fleet are HICEs and FCVs and 5% BEVs. Excluding hydrogen vehicles from the vehicle fleet can result in an average annual cost of US$562 per vehicle between 2015 and 2050. Co-production of hydrogen and electricity using coal gasification with carbon capture and storage is the dominant long term hydrogen production technology. (author)

Energy Technology Data Exchange (ETDEWEB)

Various main circuit equipment with large capacity GTO thyristors are outlined for AC and DC electric cars. The configuration of a PWM converter system is presented for the AC main motor drive system of the Shinkansen trains, and its following features are described: the high power factor control capable of keeping a power factor 100% constantly, energy saving by power regenerative braking, the small triple structure with large capacity reverse-conducting GTO thyristors of 4,500V/3,000A, and the reduction of equivalent interfering current and harmonic current by three phase-triple phase difference operation. Furthermore, a control logic equipment with 16 bit MPU and a main transformer are outlined, and the verification test results of the control logic equipment by an analog model simulation and the combinational test results of the commercial equipment are reported. Prototype VVVF inverter system for DC electric cars is also presented. 6 ...

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) Headquarters and associated contractors have developed an IBM PC-based software package that estimates costs, schedules, and public and occupational health risks for a range of mixed-waste management options. A key application of the software package is the comparison of various waste-treatment options documented in the draft Site Treatment Plans prepared in accordance with the requirements of the Federal Facility Compliance Act of 1992. This automated Systems Analysis Methodology consists of a user interface for configuring complexwide or site-specific waste-management options; calculational algorithms for cost, schedule and risk; and user-selected graphical or tabular output of results. The mixed-waste management activities modeled in the automated Systems Analysis Methodology include waste storage, characterization, handling, transportation, treatment, and disposal. Analyses of treatment options identified in the draft Site ...

Science.gov (United States)

Website hosted by the American Ceramics Society with history of ceramics education, along with notable ceramic engineering educators. "In May 1894, two rooms in the basement of The Ohio State University?s College of Engineering were set aside to create a new department: Clay-Working and Ceramics. Founded with a $10,000 grant from the State of Ohio, the department was the first of its kind anywhere in the nation. The course of study was the idea and personal project of Edward Orton Jr., a young mining engineer. Orton had gathered his ceramic knowledge, piece by piece, from various jobs in coalmines, glass factories and steel plants. In 1893 he was the superintendent for a factory that made paving bricks. Orton?s factory, hit by an ?acute crisis,? closed, leaving him with some unexpected extra time. He used the opportunity to lobby for the passage of what some people dubbed the ?Mud Pie Bill? ? legislated funding to establish ...

International Nuclear Information System (INIS)

Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries together wth high demand for the environment saving have introduced a new energy strategy ...

International Nuclear Information System (INIS)

The author blows the whistle about what he considers as a worldwide environmental crisis. He brings a fresh outlook to the crises of destabilizing climate change and rising competition for energy - both of which could poison our world if we do not act quickly and collectively. His argument speaks to all of us who are concerned about the state of America in the global future. The author proposes that an ambitious national strategy - which he calls 'Geo-Greenism' - is not only what we need to save the planet from overheating; it is what we need to make America healthier, richer, more innovative, more productive, and more secure. He explains a new era - the Energy-Climate era - through an illuminating account of recent events. He shows how 9/11, Hurricane Katrina, and the flattening of the world by the Internet (which brought 3 billion new consumers onto the world stage) have combined to bring climate and ...

Energy Technology Data Exchange (ETDEWEB)

Vehicle heating requires a substantial amount of energy. Engines in conventional cars produce enough waste heat to provide comfort heating and defogging/defrosting, even under very extreme conditions. Electric vehicles (EVs), however, generate little waste heat. Using battery energy for heating may consume a substantial fraction of the energy storage capacity, reducing the vehicle range, which is one of the most important parameters in determining EV acceptability. Water vapor generated by the vehicle passengers is in large part responsible for the high heating loads existing in vehicles. In cold climates, the generation of water vapor inside the car may result in water condensation on the windows, diminishing visibility. Two strategies are commonly used to avoid condensation on windows: windows are kept warm, and a large amount of ambient air is introduced in the vehicle. Either strategy results in a substantial heating ...

Science.gov (United States)

The Defense Advanced Research Projects Agency (DARPA) inaugurated a program addressing research and development for an Exoskeleton for Human Performance Augmentation in FY!2001. A team consisting of Oak Ridge National Laboratory, the prime contractor, AeroVironment, Inc., the Army Research Laboratory, the University of Minnesota, and the Virginia Polytechnic Institute has recently completed an 18-month Phase I effort in support of this DARPA program. The Phase I effort focused on the development and proof-of-concept demonstrations for key enabling technologies, laying the foundation for subsequently building and demonstrating a prototype exoskeleton. The overall approach was driven by the need to optimize energy efficiency while providing a system that augmented the operator in as transparent manner as possible (non-impeding). These needs led to the evolution of two key distinguishing features of this team's approach. The first is the ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility Study-II examined a high-performance Neutrino Factory providing 1 x 10{sup 20} neutrinos per year aimed at a long-baseline detector. The Study was sponsored jointly by BNL and the Neutrino Factory and Muon Collider Collaboration ration (MC) and is based on a 1 MW proton driver operating at 24 GeV, i.e., an upgraded version of the AGS accelerator. Compared with the earlier FNAL-sponsored study (Feasibility Study-I), there is a sixfold improvement in performance. Here we describe details of the implementation of Study-II concepts and discuss their efficacy. Alternative approaches that will be pursued in follow-on R and D activities are also described briefly.

Energy Technology Data Exchange (ETDEWEB)

Interesting developments in linear accelerators have been attained over the past 45 years. The status of linear accelerators and future possibilities are described in context of demanding applications and technology maturity. Features of industrial or `factory`-type applications are high availability, economic operations, low investment cost and ease of running a facility. All features have been demonstrated in one manner or another at large operating facilities for the research community; within a different context that has been argued in the past to be not as demanding as for `factory` installation. In addition, comments are made relative to intense beam power levels and choices that can be made for power levels below 10 MW, on the assumption that a cw beam is required. 1 fig., 1 tab.

International Nuclear Information System (INIS)

In the third millennium, when the main words are globalization, world net of computers, genetic code and efficiency, deep transformations have been incorporated to human behavior. Among such transformations it may be pointed out, matching with the objectives of this study, the modem consumer's profile. The consumers have quickly become more and more conscious and demanding regarding to the quality of the available products in the market. In that sense, the consumer's concern about the natural and healthy appearance, as well as the preservation of the nutritious content of the foods, have been a constant sign of alert for producers and suppliers. Besides, the timeless for domestic preparation of foods have imposed the use of minimally processed as an incontestable reality. A barrier for the production of minimally processed foods is imposed by the degree of perishability of certain products, such as the cassava-parsley. This vegetable is a source of energy, calcium, ...

International Nuclear Information System (INIS)

Vacuum glazing consists of an evacuated space between two sheets of glass. Vacuum glazing has a large effect on energy savings in houses and buildings. Vacuum glazing can achieve higher insulating performance than conventional insulated glazing. Nippon Sheet Glass has successfully developed conventional vacuum glazing. In this study we investigated an advanced form of vacuum glazing. Its thermal insulation ability is equivalent to 100 mm thick glass wool thermal insulation. This vacuum glazing contained a SnO_2:F low emissivity surface. The influence of the residual gas in a vacuum space on heat flow is important to performance. For long-term thermal stability, it is very important to maintain vacuum stability. To understand this better, we studied the behavior of outgassing from the inside glass surfaces exposed to an external energy source. We have studied the behavior of outgassing from a glass surface using a Nd:YAG ...

Energy Technology Data Exchange (ETDEWEB)

This article described a full-scale green renovation project undertaken by a construction management firm in Newton, Massachusetts. Chapman Construction and Design began renovating its own office building in late 2007 and completed it in September 2008. The firm set out to achieve LEED Platinum certification from the United States Green Building Council. The project involved energy saving modifications to its mechanical systems; replacing plumbing fixtures with high efficiency alternatives to reduce water consumption by at least 40 per cent; installing skylights and additional windows to allow more natural light into the interior space; salvaging doors, lighting, metal studs and masonry whenever possible; and using sustainable products such as recyclable carpets, tiles and low-VOC paint. The main feature of the renovation was a new 47 kW (DC) photovoltaic (PV) solar power array installed on the rooftop. The PV array includes 208 panels and a ...

Energy Technology Data Exchange (ETDEWEB)

A detailed definitive cost estimate is given for an ethanol/gasohol storage and blending terminal serving a planned distillery at a Louisiana sugar factory. Included are an analysis of the accuracy of the estimate, labor rates efficiency, materials and labor escalation, as well as detailed calculations for each account of the project. (LEW)

Energy Technology Data Exchange (ETDEWEB)

In this study, we investigate an inter-industrial and inter-regional recycling system for industrial waste by the cement industry in Japan. We develop a linear programming model that represents cement production processes and waste transportation of all cement factories in Japan. We simulate cost and CO{sub 2}-minimizing systems. The result implies that making waste transportation more efficient in cost is an effective means for CO{sub 2} reduction. (author)

Energy Technology Data Exchange (ETDEWEB)

The advent of sophisticated automation equipment and computer hardware and software is changing the way manufacturing is carried out. To compete in the global marketplace, manufacturing companies must integrate these new technologies into their factories. In addition, they must integrate the planning, control, and data management methodologies needed to make effective use of these technologies. This paper provides an overview of recent approaches to achieving this enterprise integration. It then describes, using simulation as a particular example, a new tool`s perspective of enterprise integration.

International Nuclear Information System (INIS)

At a military base in the Southeastern US, an energy services company (ESCO) has proposed to retrofit more than 1,000 family residences with geothermal heat pumps as part of an energy savings performance contract (ESPC). Each residence is to have one heat pump with its own ground heat exchanger consisting of two or more vertical bores. A design firm hired by the ESCO sized the heat pumps to meet peak cooling loads, and sized the borefields to limit the maximum entering water temperature (EWT) to the heat pumps to 95 F (35 C). Because there is some disagreement in the geothermal heat pump industry over the peak temperature to be used for design (some designers and design manuals recommend temperatures as low as 85 F[29 C], while equipment manufacturers and others specify temperatures of 100 F[38 C] or higher) the authors were requested to examine the designs in detail to determine whether the 95 F (35 C) limit was adequate ...

Energy Technology Data Exchange (ETDEWEB)

Ethanol has excellent fuel properties, such as high octane, high heat of vaporization and low photochemical reactivity in the atmosphere. It is less volatile than gasoline and there is lower smog formation from evaporative emissions of pure ethanol compared to gasoline. As such, ethanol has emerged as an important alternative energy source that is sustainable, efficient, cost effective, convenient and safe. In 2006, global production of ethanol reached 13.5 billion gallons, up from 12.1 billion gallons in 2005. However, in light of the current debate of food versus fuel, the industry must shift to non-food feedstocks. This paper described an emerging technology to cost-effectively produce ethanol from sweet sorghum stalks, the most promising alternative feedstock to corn, via solid state fermentation (SSF). Experiments of advanced solid state fermentation (ASSF) for ethanol production from sweet sorghum by Saccharomyces cerevisiae were conducted in laboratory and ...

Energy Technology Data Exchange (ETDEWEB)

Like other Central European countries, Poland faces the twin challenges of improving environmental quality while also fostering sustainable economic development. In this study we examine the costs of different standards for air pollution control, and the cost savings from using incentive-based policy instruments in lieu of more rigid command-and-control policies. The comparisons are based on the results of a simulation model of energy use and air pollution control for the Polish economy over 1990-2015. The model simulates least-cost energy supply decisions under different environmental policy assumptions, the corresponding emissions, and the cost of achieving the specified policy objectives. The model results suggest that incentive-based policies will have efficiency gains over command policies that are at least worthy of consideration and may be quite substantial. The size of the gains in practice depends in part on how ...

Energy Technology Data Exchange (ETDEWEB)

Oregon State University (OSU) and the Pacific Northwest National Laboratory (PNNL) were funded by the U.S. Department of Energy to conduct research focused on resolving the key technical issues that limited the deployment of efficient and extremely compact microtechnology based heat actuated absorption heat pumps and gas absorbers. Success in demonstrating these technologies will reduce the main barriers to the deployment of a technology that can significantly reduce energy consumption in the building, automotive and industrial sectors while providing a technology that can improve our ability to sequester CO{sub 2}. The proposed research cost $939,477. $539,477 of the proposed amount funded research conducted at OSU while the balance ($400,000) was used at PNNL. The project lasted 42 months and started in April 2001. Recent developments at the Pacific Northwest National Laboratory and Oregon State University suggest that the performance of ...

British Library Electronic Table of Contents (United Kingdom)

The economic feasibility of the residential solar thermal (ST) cooling system designed in the companion article [1] is ascertained by comparing it with a solar electric (SE) cooling system, and also with the baseline (i.e., control case), a grid dependent, highest efficiency COPC=5.66 heat pump. The economic scenario is analyzed for 24 cities across the southern USA, south of the 37degreeN. The SE cooling system provides lifecycle (20 year) savings to the homeowner only where electric rates are high and it is heavily subsidized. The overall societal effect (sum of taxpayer funded rebate and homeowner savings) is actually an increased cost everywhere except the California Central Valley, where the net savings is $1500. In the same valley, The ST cooling system provides greater lifecycle sav...

Energy Technology Data Exchange (ETDEWEB)

Waste management has gone through a history of shifting problems, demands, and strategies over the years. In contrast to the long prevailing view that the problem could be solved by hiding or moving it, waste is now viewed as a problem ranging from local to global concern, and as being an integral part of several sectors in society. Decisive for this view has been society's increasing complexity and thus the increasing complexity of waste, together with a general development of environmental consciousness, moving from local focus on point emission sources, to regional and global issues of more complex nature. This thesis is about the development and application ORWARE; a model for computer aided environmental systems analysis of municipal waste management. Its origin is the hypothesis that widened perspectives are needed in waste management decision-making to avoid severe sub-optimisation of environmental performance. With a strong foundation in life cycle assessment (LCA), ...

Energy Technology Data Exchange (ETDEWEB)

An overview is presented of the US heating and space conditioning market, with specific emphasis on the type of fuel used. The author highlights he drive of electric utilities to increase their penetration in the space heating markets, and showed how geothermal heat pumps (GHPs) were recognized by utilities as an electrotechnology for all seasons; beneficial for customers, electric utilities and the environment. Then he focused on the utility driven National Earth Comfort Program (officially Geothermal Heat Pump Technology Demonstration and Market Mobilization Program) is a collaborative effort with the US Department of Energy and other public and private sector organizations. It will be implemented by the Geothermal Heat Pump Consortium, Inc. (GHPC), and is designed for the utility industry`s Climate Challenge under the President`s Climate Change Action Plan. The program has a budget of 100 million US$ until the year 2000. Program goals include: reduce annual ...

Energy Technology Data Exchange (ETDEWEB)

More than two and a half years of monitoring of a passive house school and day-care centre in Frankfurt a. M. show comfortable indoor climate and good air quality. The space heat consumption is low and shows savings of approximately 90 % as compared to average existing schools. Excellent performance was also achieved in terms of primary energy. The results of further analyses of the efficient ventilation system with heat recovery, the perimeter insulation as an alternative to floor slab insulation and the influence of the air change due to the entrance door are presented. (Abstract Copyright [2008], Wiley Periodicals, Inc.) [German] Ueber zweieinhalb Jahre Monitoring einer Passivhaus-Schule und Kindertagesstaette (KiTa) in Frankfurt a.M. zeigt behagliche raumklimatische Bedingungen bei guten Luftqualitaeten. Die Heizwaermeverbrauchswerte liegen wie erwartet niedrig und zeigen Einsparungen um 90 % gegenueber dem Durchschnitt im Bestand. Auch ...

Energy Technology Data Exchange (ETDEWEB)

In 1994, the United States Department of Energy, the United States electric utilities and the geothermal heat pump (GeoExchange) industry formed a non-profit collaborative effort called the Geothermal Heat Pump Consortium (GHPC). The objectives were the reduction and/or elimination of 1.5 million metric tons of carbon equivalent per year and making geothermal heat pumps a significant part of the Heating Ventilation Air Cooling (HVAC) industry. Federal funding of 35 million dollars over six years was matched by 65 million dollars of private sector funds to attain these objectives and create a self-sustainable GeoExchange market. The major accomplishments of this endeavour, as well as the lessons learned were presented in this paper. The infrastructure was strengthened, first cost was reduced, and awareness of the technology was increased over the past six years as a result of the efforts deployed by the GHPC. More than 500,000 units are already installed, which ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility study is conducted for introduction of a top pressure recovery turbine (TRT) in China's Panzhihua Iron and Steel (Group) Company, Sichuan Province, for the potential project to simultaneously contribute to abatement of the greenhouse effect gases and to sustainable economic development of the counterpart country. This project considers to adopt the TRTs in 3 blast furnaces (No.1 to 3) of the 4 furnaces in service at the works, producing 2,500,000 t/y of crude steel, where the No.4 furnace is already provided with the model system and not considered in this project. According to the feasibility study results, the total fund required is 5.46 billion yen (Japan-made facilities: 4.172 billion yen, and China-made facilities: 1.288 billion yen), energy-saving effect is 36,467 t/y as crude, greenhouse effect gas emission abatement effect: 112,830 t/y as CO2, and pay-off period is 8.3 years. This plan considers to adopt almost the same facilities as ...

Energy Technology Data Exchange (ETDEWEB)

It is the Office of protection against the ionizing radiations (O.P.R.I.) who alerted the A.C.R.O. that a new ruthenium incident had arisen to the factory Cogema - La Hague on October 31., 2001. The A.C.R.O. immediately made a campaign of analyses the results of which are presented in this note. The previous similar incident dates May 18., 2001. A loss of depression in the workshop R7 of the factory UP2-800 specialized in the vitrification had brought an unchecked release, by one of the smokestacks, composed essentially of radioactive ruthenium and rhodium; the evacuated activity was estimated by the operator at approximately 11 MBq. The measures in environment made by the A.C.R.O. had led the association to question the Authority of Nuclear Safety about the total quantity of release announced by the operator. Having presented the results of the measures of radioactivity in the environment made following the incident of 31. october 2001, an ...

Energy Technology Data Exchange (ETDEWEB)

Wonderful opportunities await particle physics over the next decade, with the coming of the Large Hadron Collider at CERN to explore the 1-TeV scale (extending efforts at LEP and the Tevatron to unravel the nature of electroweak symmetry breaking) and many initiatives to develop our understanding of the problem of identity: what makes a neutrino a neutrino and a top quark a top quark. Here I have in mind the work of the B factories and the Tevatron collider on CP violation and the weak interactions of the b quark; the wonderfully sensitive experiments at Brookhaven, CERN, Fermilab, and Frascati on CP violation and rare decays of kaons; the prospect of definitive accelerator experiments on neutrino oscillations and the nature of the neutrinos; and a host of new experiments on the sensitivity frontier. We might even learn to read experiment for clues about the dimensionality of spacetime. If we are inventive enough, we may be able to follow this rich menu with the ...

Energy Technology Data Exchange (ETDEWEB)

Particle physics is driven by five great topics. Neutrino oscillations and masses are now at the fore. The standard model with extensions to supersymmetry and a Higgs to generate mass explains much of the field. The origins of CP violation are not understood. The possibility of extra dimensions has raised tantalizing new questions. A fifth topic lurking in the background is the possibility of something totally different. Many of the questions raised by these topics require powerful new accelerators. It is not an overstatement to say that for some of the issues, the accelerator is almost the experiment. Indeed some of the questions require machines beyond our present capability. As this volume attests, there are parts of the particle physics program that have been significantly advanced without the use of accelerators such as the subject of neutrino oscillations and many aspects of the particle-cosmology interface. At this stage in the development of physics, both approaches are needed ...

UK PubMed Central (United Kingdom)

A public health emergency such as an influenza pandemic will lead to shortages of mechanical ventilators, critical care beds, and other potentially life saving treatments. This will raise difficult...Full Text Available

Science.gov (United States)

This purpose of this paper is to describe the optimizing Peripherally Inserted Central Catheter (PICC) insertion, revising data collection strategies, estimating workloads, and calculating the financial savings generated by the vascular access nurse (VAN)...

International Science & Technology Center (ISTC)

Development of New Resource-Saving Technologies for Ceramic Material Production: High resistant Pigments, Heat Shielding, Plasters, Filters, etc.; by the Method of Controllable Thermosynthesis in Combustion Wave Using Industrial Metal-Containing Wastes

Energy Technology Data Exchange (ETDEWEB)

This paper has the objective of presenting the philosophy of Static Var Compensator (SVC) Control as well the necessary adjustments in the project of control system to guarantee suitable performance under different operating conditions. The verification on the performance of the SVC control has been done by Transient Network Analyzer (TNA/CEPEL) studies, commissioning tests and a factory tests. The SVC is the type of Thyristor Controlled Reactor (TCR) and Thyristor Switched Capacitor (TSC). (author) 3 refs., 12 figs.

Energy Technology Data Exchange (ETDEWEB)

This article describes innovations in new-boiler startups, based on experiences at United Development Group`s 50-MW Niagra cogeneration facility, Niagra Falls, NY. The plant comprises: a circulating coal fluidized bed boiler supplying steam to a nearby factory and electricity to the grid. Before operation the system was flushed with demineralized water, and the boiler degreased, the steam blow relied on a new procedure involving a continuous flow of steam. Startup was then initiated, following manufacturers heatup rate and soak times closely. After startup boiler tube sections were checked, and cleaned if necessary. 1 fig.

Energy Technology Data Exchange (ETDEWEB)

The role of computers has become increasingly important for oil and gas field research and operations support. Today, the computer network is an integral part of the increasingly complex computing environment that exists in many companies. Computer networks allow users to efficiently share information, software, and hardware to support critical global communication needs. Because users are able to share software and hardware, the use of computer networks can also result in significant cost savings. This paper describes typical network loading and demand levels for shared software applications on a computer network that has been used for several years.

International Nuclear Information System (INIS)

More important than waste generation numbers, the pollution prevention and waste minimization successes achieved at Hanford in 1993 have reduced waste and improved operations at the Site. Just a few of these projects are: A small research nuclear reactor, unused and destined for disposal as low level radioactive waste, was provided to a Texas University for their nuclear research program, avoiding 25 cubic meters of waste and saving $116,000. By changing the slope on a asphalt lot in front of a waste storage pad, run-off rainwater was prevented from becoming mixed low level waste water, preventing 40 cubic meters of waste and saving $750,000. Through more efficient electrostatic paint spraying equipment and a solvent recovery system, a paint shop reduced hazardous waste by 3,500 kilograms, saving $90,800. During the demolition of a large decommissioned building, more than 90% of the building's material was recycled by ...

Energy Technology Data Exchange (ETDEWEB)

The central research question of this thesis is: What is the potential of multi-functional biomass systems to improve the costs and the land use efficiency of saving non-renewable energy consumption and reducing GHG (greenhouse gases) emissions in quantitative terms? Therefore, in the following chapters the performance of multi-functional biomass systems is quantified. Biomass system costs are investigated from a societal perspective using e.g. low discount rates. A main focus will be on the review of methodologies for accounting GHG emissions, non-renewable energy consumption, agricultural land use and costs as well as the adaptation of these methodologies to special aspects of multifunctional biomass use. The analysis of the potential benefits of multi-functional biomass systems is carried out by several case studies of biomass systems including various waste treatment technologies for the short term that appeared ...

Science.gov (United States)

This paper builds upon previous work [Sprigg and Ehlen, 2004] by introducing a bond market into a model of production and employment. The previous paper described an economy in which households choose whether to enter the labor and product markets based on wages and prices. Firms experiment with prices and employment levels to maximize their profits. We developed agent-based simulations using Aspen, a powerful economic modeling tool developed at Sandia, to demonstrate that multiple-firm economies converge toward the competitive equilibria typified by lower prices and higher output and employment, but also suffer from market noise stemming from consumer churn. In this paper we introduce a bond market as a mechanism for household savings. We simulate an economy of continuous overlapping generations in which each household grows older in the course of the simulation and continually revises its target level of savings according to a life-cycle ...

Energy Technology Data Exchange (ETDEWEB)

Up to this time the sigmoid colostomy has been widely accepted and conventional treatment for radiation-injured rectum, but patients without residual malignancy strongly desire to live without colostomy. We have tried to remove the involved rectal segments by sphincter-saving procedures. Four patients underwent these procedures, pull-through procedure in three and low anterior resection in one. Among sphincter-saving procedures, pull-through procedure was most adequate. Provided the following five conditions are fulfilled, pull-through procedure should be considered for severe radiation-injured rectum. (1) No recurrence of initial malignancy in the pelvis. (2) More than 2 cm intact rectal segment above dentate line may be preserved. (3) No radiation-injured segment in upper sigmoid. (4) No severe radiation damage in small intestine. (5) Patients under 70 year-old, with normal tonus of anal sphincter.

International Nuclear Information System (INIS)

Since the radiometric measuring technique was introduced for industrial measuring and control engineering 15 to 20 years ago, the advantages of this technique have become more and more evident and have led to its world-wide application. In the last 15 to 20 years this method has become the standard one in this field. Its major advantages as compared with conventional methods are: contactless measurement; high reliability and accuracy; no mechanically moving parts; and no maintenance required. Despite higher investment costs the application of this method is paid off within a very short time owing to a higher output and the savings in maintenance costs. Some chemo-technical methods can be realized on a grand scale only when radiometric measuring equipment is used - e.g., urea plants, high-pressure polyethylene production. Especially in moisture measurements of blast-furnace coke are the economical advantages significant. Detailed studies have shown that the system ...

International Nuclear Information System (INIS)

We have performed extended X-ray absorption fine structure (EXAFS) analysis for artificial Cr-goethite to elucidate the local structure around Cr in Cr-goethite. The spectra were obtained using synchrotron radiation X-rays at the Photon Factory in Tsukuba. The first shell contributions were isolated by Fourier filtering EXAFS data, and the inverse Fourier transformed single-shell data were analyzed using a curve fitting method. The results show that Cr is coordinated with (7#+-#1)O"2"- ions. The protective characteristics of the Cr-goethite protective rust layer on weathering steel can be interpreted in terms of the O"2"- coordination around Cr"3"+ resulting in the creation of negative fixed charge in the Cr-goethite particles. (author)

Energy Technology Data Exchange (ETDEWEB)

In Kanazawa, Japan, air pollution from a Mn treatment factory was found to affect local junior high school students, who showed reduced respiratory function relative to their exposure to Mn. The use of Mn as an antiknock ingredient in automobile fuels has recently been introduced, placing the general population at risk of chronic low-level exposure. There are few animal studies on the effects of compounds other than manganese chloride (MnCl{sub 2}). In the case of environmental pollution by Mn, the differing physiological effects of the various chemical forms of Mn must be considered. The present study therefore examined the differences in the effects of several Mn compounds on the physiology and behavior of mice by short-term oral administration.

British Library Electronic Table of Contents (United Kingdom)

Response Surface Methodology (RSM) via Central Composite Design (CCD) was used to optimize the alkaline hydrolysis of paddy straw to improve ferulic acid extraction. The parameters involved, namely temperature (^oC), concentration of NaOH (M) and duration of extraction (h) are screened by Full Factorial Studies (FFD). The result obtained from FFD was 0.518% (5.18mg/g). The interactions between each parameters involved were studied using Central Composite Design (CCD). Upon optimization, the percentage of ferulic acid improved from 0.518% to 0.817% (8.17mg/g). The optimum conditions obtained from this study are 125^oC, 3.90M, 2.30h for temperature, concentration of NaOH and extraction time, respectively. This result shows a significant improvement than the previous published work. Details o...

CERN Document Server

We discuss the minimum requirements for a neutrino beta beam if theta_13 is discovered by an upcoming reactor experiment, such as Double Chooz or Daya Bay. We require that both neutrino mass hierarchy and leptonic CP violation can be measured to competitive precisions with a single-baseline experiment in the entire remaining theta_13 range. We find that for very high isotope production rates, such as they might be possible using a production ring, a (B,Li) beta beam with a gamma as low as 60 could already be sufficient to perform all of these measurements. If only the often used nominal source luminosities can be achieved, for example, a (Ne,He) beta beam from Fermilab to a possibly existing water Cherenkov detector at Homestake with gamma \\sim 190-350 (depending on the Double Chooz best-fit) could outperform practically any other beam technology including wide-band beam and neutrino factory.

British Library Electronic Table of Contents (United Kingdom)

Abstract In the 1990s, significant efforts were invested in the research and development of food-grade expression systems in lactic acid bacteria (LAB). At this time, Lactococcus lactis in particular was demonstrated to be an ideal cell factory for the food-grade production of recombinant proteins. Steady progress has since been made in research on LAB, including Lactococcus, Lactobacillus and Streptococcus, in the areas of recombinant enzyme production, industrial food fermentation, and gene and metabolic pathway regulation. Over the past decade, this work has also led to new approaches on chromosomal integration vectors and host/vector systems. These newly constructed food-grade gene expression systems were designed with specific attention to self-cloning strategies, food-grade selection...

British Library Electronic Table of Contents (United Kingdom)

This article explores the growth of organised crime within the Vietnamese community with particular reference to the cultivation of cannabis, money laundering and the smuggling or trafficking of children. The article begins by exploring the history and diversity of the 'Vietnamese community' in the United Kingdom and the role of Vietnamese culture in shaping their criminal enterprises. It then draws on research involving two sets of qualitative data: one set is based on 45 interviews with law enforcement personnel based in Vietnam and the United Kingdom as well as with key stakeholders in the Vietnamese community; the other set is based on structured questionnaires issued to 34 Vietnamese residents in Britain, 24 of whom are here illegally. It examines the relationship between illegal immi...

British Library Electronic Table of Contents (United Kingdom)

Statistically based experimental designs were applied to screen and optimize the bioleaching of spent hydrocracking catalyst by Penicillium simplicissimum. Eleven factors were examined for their significance on bioleaching using a Plackett-Burman factorial design. Four significant variables (pulp density, sucrose, NaNO"3, and yeast extract concentrations) were selected for the optimization studies. The combined effect of these variables on metal bioleaching was studied using a central composite design (CCD). Second-order polynomials were established to identify the relationship between the recovery percent of the metals and the four significant variables. The optimal values of the variables for maximum metals bioleaching were as follows: pulp density (4.0%, w/v), sucrose (90g/L), NaNO"3 (2...

British Library Electronic Table of Contents (United Kingdom)

Nitrogen use efficiency (NUE) of tef, a major staple crop in Ethiopia, is very low, either caused by untimely use of nitrogen (N) fertilizers or lack of other essential nutrients like sulphur (S). The average grain yield of this crop is low, averaging ?1 in farmer?s fields of the semi-arid conditions. Therefore, the present study was conducted to see the effect of the timing of combined N and S fertilization on the yield, yield components, and N and S concentration in the plant parts of the crop. A factorial combination of three rates of N (0, 70, and 105?kg?ha?1) with four rates of S (0, 16, 32, and 48?kg?ha?1) was applied in randomized complete blocks in three replications. The experiment was carried out in the 2004 and 2005 cropping seasons in the Cambisols of the semi-arid area of Ethi...

CERN Document Server

We suggest that \\psi (4040) and \\psi (4160) are strong mixtures of ground state hybrid charmonium at \\sim 4.1 GeV and the \\psi (3S) of conventional charmonium. The \\Gamma^{e^+e^-}, masses and total widths of the \\psi(4040) and \\psi(4160) are in accord with this hypothesis. Their hadronic decays are predicted to be dominated by the \\psi (3S) component and hence are correlated. In particular we find a spin counting relation \\Gamma (4160 \\rightarrow D_sD_s^*) \\sim 4 \\Gamma (4040 \\rightarrow D_sD_s) due to their common \\psi(3S) component. For D and D^* production, using \\psi(4040) branching ratios as input, we predict that the decay pattern of the \\psi(4160) will be very different from that of the \\psi(4040). These predictions may be tested in historical data from SPEAR, BES or at future Tau-Charm Factories.

International Nuclear Information System (INIS)

The potential of the yeast Candida tropicalis and Candida guillermondii was evaluated and an isolated partnership of microorganisms of waters of the Medellin River, conformed by two bacteria and one leavening, to degrade the content of organic matter present in wine produced by the factory of Licores and Alcoholes de Antioquia (FLA) in aerobic process with biomass production. For each one of the microorganisms in study this capacity of removal in units of chemical demand of oxygen was quantified (CDO); in addition, parameters were analyzed such as yield of the biomass in relation to the removed CDO and to total reducing sugars (TRS) consumed, time of fermentation and speed of growth different dilutions from wine. Also the possible inhibition was analyzed that the present phenolic compounds in this wine can cause in the biological process of degradation.

Energy Technology Data Exchange (ETDEWEB)

The handling of physical-nuclear techniques for the analysis of archaeological pieces it was carried out by first time in 1956 by the doctors Oppenheimer and Dodsom (in the United States); who wrote about the wide utilities of the neutron activation analysis (NAA), this technique requires of a nuclear reactor that could be considered like one a factory of thermal neutrons necessary to carry out this analysis. The first experiments in that were applied the NAA were on ceramic coming from the Mediterranean, in those that the relationships of the elements of sodium and manganese were determined to know their elementary composition and to identify the origin of their manufacture. Later on other study techniques were applied in archaeological materials, as the X-ray fluorescence, Moessbauer spectroscopy, scanning electron microscopy, PIXE analysis (particle induced x-ray emission), among other, this last is the matter that we will present in this work. (Author)

International Nuclear Information System (INIS)

This paper evaluates the performance of asphalt membranes by examining the chemical and permeability changes experienced by the asphalt during aging tests. The aging process was accelerated by exposing the asphalt to elevated temperatures, high oxygen concentrations, and increased strengths of aqueous oxidizing agents. The synergistic effects of the variables are evaluated by using a fractional factorial experimental design. The installation costs for a catalytically airblown asphalt liner are roughly half that of the typical polymeric materials, and also less than the rubberized asphalt membrane. The results of the initial accelerated aging tests of the asphalt membranes indicate that this material will provide stable, long-term leachate isolation in a mill tailings environment.

British Library Electronic Table of Contents (United Kingdom)

Experiments based on a 23 central composite full factorial design were carried out in 200-ml stainless-steel containers to study the pretreatment, with dilute sulfuric acid, of a sugarcane bagasse sample obtained from a local sugar?alcohol mill. The independent variables selected for study were temperature, varied from 112.5?C to 157.5?C, residence time, varied from 5.0 to 35.0 min, and sulfuric acid concentration, varied from 0.0% to 3.0% (w/v). Bagasse loading of 15% (w/w) was used in all experiments. Statistical analysis of the experimental results showed that all three independent variables significantly influenced the response variables, namely the bagasse solubilization, efficiency of xylose recovery in the hemicellulosic hydrolysate, efficiency of cellulose enzymatic saccharificatio...

Energy Technology Data Exchange (ETDEWEB)

A reduced grid model of a transmission system with a number of central power plants, consumption centers, local wind turbines and a large offshore wind farm is developed and implemented in the simulation tool PowerFactory (DIgSILENT). The reduced grid model is given by Energinet.dk, Transmission System Operator of Denmark (TSO) for Natural Gas and Electricity, to the Danish Universities and the Risoe National Laboratory. Its intended usage is education and studying of interaction between electricity-producing wind turbines and a realistic transmission system. Focus in these studies is on voltage stability issues and on the ride-through capability of different wind turbine concepts, equipped with advanced controllers, developed by the Risoe National Laboratory.

International Nuclear Information System (INIS)

The evaluation methodology utilized in deciding to change over Oyster Creek plant operation from chemical regeneration of condensate demineralizer resin beds to throwaway of this spent resin is presented. Both the economic and operational aspects considered are discussed. The evaluation shows that potential savings in the $1.1M range are feasible over a 5 year cycle. Cost sensitivity analysis results define the throwaway versus regeneration breakeven point to be 47 condensate demineralization beds per 5 year cycle. The evaluation also discusses the trade off between resin and evaporator concentrates burial volumes. Analyses are given which show that the burial volume cost equivalency of resin to solidified concentrates is 150 ft./sup 3/ of resin equals 400 ft./sup 3/ of concentrates. Based on one year of power operation in the throwaway mode, the savings and operational value anticipated in the initial study are being realized.

International Nuclear Information System (INIS)

Presented in this report are the quantitative and qualitative aspects of the more than 5,800 applications of Grafoil on-plant. The subject all-graphite product was originally made by the Union Carbide Corporation. Its utilization in the forms of valve packing, gasketing and sealant tapes for leak repair and prevention on-plant since March 1970 is marked with typical zero-leak results. For all practical purposes, the successful results with Grafoil implementation indicate an unqualified control of leakage problems that began in 1967 with the V-11 and V-12 valves in the primary system of N Reactor. Meaningfully, the accruals of savings with existing and future applications shall continue to be incalculable in personnel exposure, maintenance, and capital. Inherent in the savings are the devised methodology and innovative developments coordinately employed in resolving the leak repair problems.

Energy Technology Data Exchange (ETDEWEB)

Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this study, ALSTOM Power Inc. (ALSTOM) has investigated several coal fired power plant configurations designed to capture CO{sub 2} from effluent gas streams for use or sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). Additionally, oxygen firing in Circulating Fluid Bed Boilers (CFB's) can be more economical than ...

Energy Technology Data Exchange (ETDEWEB)

Design considerations of a combined photovoltaic-thermal (PV-T) system for a particular site and application must include thermal and electrical tradeoffs. A simplified technique for determining preliminary design and economic analyses would minimize costly computer simulation and indicate feasibility. To that end, nomographs that size an array to meet a specific annual load and determine the subsequent cost savings have been developed, and are presented in this paper.

Energy Technology Data Exchange (ETDEWEB)

Vibration of machinery plays an important role in preventive maintenance programs of machinery. It can be applied in different phases ranging from simple to computerized programs. The advantages of applying machine condition monitoring programs are numerous since vibration measurement and analysis leads to the early detection of component deterioration. The cost, savings and some details of the vibration preventive maintenance program are discussed.

Wastenet

... Reduce partner costs, save time, and overcome delays in data transmission. Data Exchanges States are currently submitting data to each other and to the EPA in the exchanges listed below. Data Exchanges are typically referred to by their acronyms, which are listed below. To find out more about EPA data exchanges, please follow the links to EPA Web sites. AQS - Air Quality Sub-system (...

Energy Technology Data Exchange (ETDEWEB)

Characteristics of advanced composites are investigated. The fibers considered are Kevlar and carbon. The greatest advantage of composites over metals is emphasized, and lies in their permitting designers to obtain properties in exactly the locations desired. Kevlar replaced S-glass on the Trident 2 missile, saving 800 lbs. and adding 800 miles to its range. Military aircraft builders find that advanced carbon composites more often than not win out over Kevlar.

British Library Electronic Table of Contents (United Kingdom)

This paper reviews the main studies on entrepreneurship conducted during the past two decades that are relevant for the understanding of various macroeconomic issues. I organize the discussion by distinguishing three groups of contributions. The first group includes studies whose main purpose is to understand the factors that affect the decision to become an entrepreneur. The second group includes studies that look at the aggregate and distributional implications of entrepreneurship for savings and investment. The third group deals with issues of economic development and growth.

Wastenet

...Chapter 11 Aqueous Solutions Chapter 11 Aqueous Solutions Download the entire chapter (PDF-136k) Drilling to China More water than rivers Saving the aquifer Drying with Xeriscapes Everywhere in the house Rainwater and graywater Creating urban watersheds Wastewater equals ...3851 Powered by Intrcomm Technology's SMC ...

Science.gov (United States)

Buildings Energy-Efficient Research Laboratories Energy Efficiency in Federal Facilities Energy Efficiency Standards Group Energy Efficient Windows Collaborative Energy &...

Energy Technology Data Exchange (ETDEWEB)

The project is devoted to the development of novel insoluble anodes for copper electrowinning and electrolytic manganese dioxide (EMD) production. The anodes are made of titanium-lead composite material produced by techniques of powder metallurgy, compaction of titanium powder, sintering and subsequent lead infiltration. The titanium-lead anode combines beneficial electrochemical behavior of a lead anode with high mechanical properties and corrosion resistance of a titanium anode. In the titanium-lead anode, the titanium stabilizes the lead, preventing it from spalling, and the lead sheathes the titanium, protecting it from passivation. Interconnections between manufacturing process, structure, composition and properties of the titanium-lead composite material were investigated. The material containing 20-30 vol.% of lead had optimal combination of mechanical and electrochemical properties. Optimal process parameters to manufacture the anodes were identified. Prototypes having ...

Science.gov (United States)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Digital control technology using micro-processor is widely used in Factory Automation area since 1980`s. However, the D{sub 2}O Vapour Recovery System in Wolsung 1 N.P.P is controlled by mechanical timer without considering the moisture condition in the Reactor Building and bed temperature, because it was designed using analog technology of 1960`s. This leads to the inefficient system operation and low D{sub 2}O recovery rate in addition to the high internal dose rate of operator. The goal of this phase II study is to develope a optimal automatic controller of D{sub 2}O vapour recovery system using PLC. We developed a control algorithm for Dual Tower Drier, a PLC control program, a operation change program and the monitoring system with a real-time simulator for system verification. (author). 15 refs., 11 figs., 2 tabs.

British Library Electronic Table of Contents (United Kingdom)

We examined whether or not BMD or bone markers were useful for assessing the risk of vertebral fractures in 248 Japanese men with type 2 diabetes. We analyzed the relationships between bone markers (osteocalcin [OC], bone-specific alkaline phosphatase [BAP], urinary N-terminal cross-linked telopeptide of type-I collagen) or BMD and HbA1c, urinary C-peptide, insulin-like growth factor-I (IGF-I), parathyroid hormone, 1,25(OH)2 vitamin D, and the presence of prevalent vertebral fractures. Multiple regression analysis adjusted for age, body height, weight, duration of diabetes, and serum creatinine showed that serum OC and OC/BAP ratio were correlated negatively with HbA1c (P?P?P?

CERN Document Server

NGC 2770 has been the host of three supernovae of Type Ib during the last 10 years, SN 1999eh, SN 2007uy and SN 2008D. SN 2008D attracted special attention due to the serendipitous discovery of an associated X-ray transient. In this paper, we study the properties of NGC 2770 and specifically the three SN sites to investigate whether this galaxy is in any way peculiar to cause a high frequency of SNe Ib. We model the global SED of the galaxy from broadband data and derive a star-formation and SN rate comparable to the values of the Milky Way. We further study the galaxy using longslit spectroscopy covering the major axis and the three SN sites. From the spectroscopic study we find subsolar metallicities for the SN sites, a high extinction and a moderate star-formation rate. In a high resolution spectrum, we also detect diffuse interstellar bands in the line-of-sight towards SN 2008. A comparison of NGC 2770 to the global properties of a galaxy sample with high SN occurance (at least 3 ...

Science.gov (United States)

Gastric dilatation-volvulus (GDV) is a life-threatening condition in dogs and other species in which the stomach dilates and rotates on itself. The etiology of the disease is multi-factorial, but explicit precipitating causes are unknown. This study sought to determine if there was a significant association between changes in hourly-measured temperature and/or atmospheric pressure and the occurrence of GDV in the population of high-risk working dogs in Texas. The odds of a day being a GDV day, given certain temperature and atmospheric pressure conditions for that day or the day before, was estimated using logistic regression models. There were 57 days in which GDV(s) occurred, representing 2.60% of the days in the 6-year study period. The months of November, December, and January collectively accounted for almost half (47%) of all cases. Disease risk was negatively associated with daily maximum temperature. An increased risk of GDV was weakly associated with the ...

Science.gov (United States)

Locomotive engineers (train drivers) on irregular work schedules reported a general coffee consumption rate higher than that reported by a comparison sample of permanent shift factory workers. The present study examines the impact of this consumption on workday and non-workday sleep behaviour and mood ratings. Twenty-seven engineers and their spouses each completed daily logs for 30 consecutive days. Daily logs were then sorted into workday and non-workday categories. Workday sleep length was significantly shorter than non-workday sleep length for both engineers and spouses. For the engineers only, coffee consumption on workdays was higher than on non-workdays. This increased coffee consumption was correlated with longer sleep latency, increased negative mood, and decreased positive mood on both work and non-workdays. This was not true for spouses. These results may be related to a days-off carry-over effect of caffeine or a general consumption behaviour ...

British Library Electronic Table of Contents (United Kingdom)

The main drawback of Ni/YSZ anode supports for solid oxide fuel cell application is their low tolerance to reducing and oxidizing (RedOx) atmosphere changes, owing to the Ni/NiO volume variation. This work describes a structured approach based on design of experiments for optimizing the microstructure for RedOx stability enhancement. A full factorial hypercube design and the response surface methodology are applied with the variables and their variation range defined as: (1) NiO proportion (40-60wt% of the ceramic powders), (2) pore-former proportion (0-30wt% corresponding to 0-64vol.%), (3) NiO particle size (0.5-8mm) and (4) 8YSZ particle size (0.6-9mm). To obtain quadratic response models, 25 different compositions were prepared forming a central composite design. The measured responses...

Energy Technology Data Exchange (ETDEWEB)

Pyrolysis of Greek fir wood samples in a fluidized bed reactor was studied. The experimental conditions selected control the yield of gaseous, liquid and solid products. The factors examined were: pyrolysis temperature, mean particle size, pressure, residence time of volatiles, lignin content of biomass and moisture content. The experiments were performed on the basis of a 12-run Plackett-Burman fractional factorial design. Statistical analysis of the data showed that the pyrolysis temperature is the main factor affecting the distribution of the yields of liquids, their phenolic fraction and gases in the range of experimental conditions tested. Empirical expressions were obtained from linear regression giving the yields of liquids, phenols and gases in terms of temperature. The maximum predicted yields were 56 and 12 wt.% on a moisture-free basis at 520 C and 545 C for liquids and phenols, respectively. The yield of gases increased proportionally with temperature. ...