Energy Technology Data Exchange (ETDEWEB)

A research report presents the basic data required when designing a building with minimal environmental impacts. Topics covered include the energy consumption of building elements during their lifetime, the environmental implications linked to the extraction and processing of building material and the energy consumed in buildings by the occupants. (UK)

Science.gov (United States)

Contents: Energy Use; Building Fabric Performance; Ventilation and Infiltration; Passive Solar Design; Heating Systems and Controls; Hot and Cold Water Provision; and Lighting and Electrical Appliances.

Energy Technology Data Exchange (ETDEWEB)

Purpose of this assessment for this town in the Slovak Republic is to develop information on the building sector energy efficiency and improvement potential for use by town management to support decisions on providing energy services to Handlova citizens. Objectives were to characterize baseline space and water heat energy use and efficiency improvement potential in the residential and nonresidential building sectors. Intention was to identify major areas of efficiency improvement potential and cost-effectiveness. Four levels of energy and fuel prices were used. A significant efficiency resource exists in the space and water heating end uses in these building sectors; it amounts to 42% of the total building sector space and water heat energy consumption.

Energy Technology Data Exchange (ETDEWEB)

A research report describes the energy efficiency techniques to be employed in designing a building which is ``green``. Topics covered include building fabric performance, ventilation and infiltration, passive solar design, heating systems and controls, hot and cold water provision, lighting and electrical appliances. (UK)

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy Office of Building Technology, State and Community Programs sponsored EcoTecture Solutions, Inc. (dba Sustainable Living Alliance {trademark}) in producing two home tours showcasing energy- and resource-efficient buildings in Austin, Texas, held on October 16, 1999, and Albuquerque, New Mexico, held on May 20, 2000. Lists are given of the notable building technologies, passive solar design features, and energy- and water-efficient technologies and design employed in the houses. There were over 1200 visitors to the 22 residential and 3 commercial buildings included in the tour.

Energy Technology Data Exchange (ETDEWEB)

A survey was conducted to determine the sources of buildings energy conservation case studies and educational aids available in Canada. In total 785 consultants, educational institutions, building developers, manufacturers and government agencies were contacted. The results of this survey provide an indication of those agencies in Canada most actively involved with energy conservation in buildings, a listing of those agencies in Canada having case study information and/or educational aids materials available related to energy conservation in buildings, and a broad description of the subject area of the case studies and educational aids listed. The results of this study are intended to provide a source listing of energy conservation case studies and educational aids to the Buildings ...

Energy Technology Data Exchange (ETDEWEB)

The dwelling is equipped with solar collectors which heat the air circulating in the cavity walls and the space beneath the floors. The thermal aspects of such a building are described. Heat balance, losses, heating by the sun in different seasons are described. Different measures taken to reduce the energy losses are described.

Energy Technology Data Exchange (ETDEWEB)

In accordance with federal legislation, the U.S. Department of Energy (DOE) has conducted a project to demonstrate use of its Energy Conservation Voluntary Performance Standards for Commercial and Multi-Family High-Rise Residential Buildings; Mandatory for New Federal Buildings; Interim Rule (referred to in this report as DOE-1993). A key requisite of the legislation requires DOE to develop commercial building energy standards that are cost effective. During the demonstration project, DOE specifically addressed this issue by assessing the impacts of the standards on (1) construction costs, (2) builders (and especially small builders) of multi-family, high-rise buildings, and (3) the ability of low-to moderate-income persons to purchase or rent units in such buildings. This document reports on this project.

British Library Electronic Table of Contents (United Kingdom)

There is increasing pressure to operate laboratory facilities in environmentally and financially sustainable ways. A key factor in achieving this goal is careful consideration of how energy is used by the buildings' ventilation system, both for conditioning air supplied to the laboratories and the energy used moving air through the building. Traditionally, laboratory energy use is treated as an engineering concern within the scope of the building's overall design and operation. However, this approach limits the involvement of key stakeholders in many important decisions and can lead to unexpected safety concerns for the laboratory's users. We believe that a broad view of the parties affected by a laboratory building's operations is necessary to avoid having the various stakeholders working...

Energy Technology Data Exchange (ETDEWEB)

Because there are more than 101 million residential households in the United States today, it is not surprising that existing residential buildings represent an extremely large source of potential energy savings. Because thousands of these homes are renovated each year, Building America is investigating the best ways to make existing homes more energy-efficient, based on lessons learned from research in new homes. The Building America program is aiming for a 20%-30% reduction in energy use in existing homes by 2020. The strategy for the existing homes project of Building America is to establish technology pathways that reduce energy consumption cost-effectively in American homes. The existing buildings project focuses on finding ways to adapt the results from the new homes research to retrofit ...

Energy Technology Data Exchange (ETDEWEB)

The development of comfort in buildings throughout the centuries was influenced by the demand for progress, wealth and innovation in various respects. At present, it seems that progress may only be possible by taking into account the environment and creating methods of reducing further damage to the environment. The innovative feature of future progress my be reducing the impact on the environment from human and building activities by using appropriate technology. As it is impossible to build without any impact on the environment and this is likely to be so in the future, the objective is and will be to find solutions for buildings which are more compatible with the environment. The objective is to demonstrate that it is viable to design buildings with minimized impact on the environment, while still maintaining appropriate comfort levels.

Energy Technology Data Exchange (ETDEWEB)

This document provides guidance for modeling and inspecting energy-efficient property in commercial buildings for certification of the energy and power cost savings related to Section 179D of the Internal Revenue Code enacted in Section 1331 of the 2005 Energy Policy Act and noted in Internal Revenue Service Notice 2006-52. Specifically, Section 179D provides federal tax deductions for energy-efficient property related to a commercial building's envelope; interior lighting; heating, ventilating, and air conditioning; and service hot water systems.

Wastenet

situ by isolating portions of the building envelope and performing tests .MAXIMUM ALLOWED LOAD ...and shall identify commissioning team members who will perform testing and prepare documentation.The commissioning agent may be

Energy Technology Data Exchange (ETDEWEB)

This thesis examines the costs and benefits of energy management in office buildings and investigates the relationships between operating costs, space lease contracts, and building value. Energy management be building owners and managers begins with monitoring and analysing building energy, use and continues by reducing energy consumption through operating procedure changes, equipment replacement and control personnel training and continued monitoring. The cost to complete energy management projects in 12 British Columbia office buildings is analyzed. The average before-tax internal rate of return for the 12 energy management programs was 22.1% on total expenditures of Canadian $1.2 million. Nine of the buildings are owned and occupied by ...

Energy Technology Data Exchange (ETDEWEB)

At the 7th Healthy Buildings Conference, which was held in Singapore, 7-11 December 2003, more than 500 articles to improve public health and productivity of workers in buildings and the performance of installations. Special attention is paid to indoor air quality and thermal comfort in relation to energy efficiency. [Dutch] Op de laatste Healthy Buildings conferentie, december 2003 in Singapore, werden meer dan 500 artikelen gepresenteerd over het creeren van gezonde, productiviteit verhogende gebouwen en installaties. Deze keer lag de nadruk op binnenluchtkwaliteit en thermisch binnenklimaat, onder andere op het aspect energiezuinigheid. Opvallend was ook de aandacht die de problemen met binnenluchtkwaliteit in ontwikkelingslanden kreeg.

Energy Technology Data Exchange (ETDEWEB)

This official IEA report is a deliverable of IEA SHC Task 21/IEA BCS Annex 29: Daylight in Buildings. The Task focuses on daylighting systems and strategies which can be applied in new and existing buildings with a high potential electricity saving potential such as offices, schools, commercial, and institutional buildings. The daylighting performance of these strategies and systems is tested in laboratory facilities, through modeling, and in real case study buildings. This paper provides methods and procedures to evaluate the daylighting performance of real buildings. Annex 29 case studies located in Europe, North America, and Australia. It is a deliverable of Subtask D research projects. The main objective of Subtask D, as stated in the Implementing Agreement of Task 21/Annex 29, is `to demonstrate the viability of daylighting buildings in various world ...

Energy Technology Data Exchange (ETDEWEB)

This paper seeks to challenge the traditional way in which we assess the value of green buildings in terms of their environmental friendliness, energy efficiency and whole life cost. In the UK, quantity surveyors (or cost consultants) have a perception that more energy efficient and environmentally friendly buildings cost between 5% and 15% more to build from the outset. This common assumption is not backed up by recent research and should be questioned. Construction professionals need to be informed of the whole life cost and environmental impact of buildings so that they can encourage key stakeholders to make more sustainable choices. These emerging issues together with practical tools are considered with case studies from recent projects. (Author)

Energy Technology Data Exchange (ETDEWEB)

Southern California Gas Co.`s (SoCalGas) Energy Resource Center (ERC) in Downey, Calif. is a 45,000 ft{sup 2} (4,181 m{sup 21}) conference and education center created to help energy decision-makers find the most energy-efficient, cost-effective and environment-sensitive solutions to their energy requirements. The center has 36,000 ft{sup 2} (3,344 m{sup 2}) of remodeled space and 9,000 ft{sup 2} (836 m{sup 2}) of new space, all designed to showcase the latest energy-efficient and environment-sensitive technologies. The building is one of the 25 buildings in the US to be designated as Energy Star Showcase buildings by the US Environmental Protection Agency.

Energy Technology Data Exchange (ETDEWEB)

This document gathers the presentations given at the first French national meetings of solar energy for the development of solar systems in buildings. The meeting was organized over two days. The first day comprises 4 workshops about: urbanism and planning, cultural acceptability of solar energy in buildings (the OPAC 38 housing association, point of view on an energy information point, the Freiburg (Germany) solar region and marketing examples), technical integration to the structure (Clipsol solutions), and economical criteria (compared impacts of R and D public photovoltaic programs (USA, Japan, Germany, France, Italy), financing of rehabilitation projects, global approach of solar photovoltaic energy, technical solutions and strategy of products development, why and how to make an economical analysis of solar energy applications in the ...

Energy Technology Data Exchange (ETDEWEB)

First, attention is paid to the development and use of new construction techniques, including the use of new building materials, e.g. synthetic materials and the so-called steel frame method. Next, the reduction of the energy consumption during the service life of a house is discussed. The reduction can be realized by means of passive methods, e.g. improved windows, thermal insulation and design, or by means of active methods, e.g. electric load monitoring. The information in this article mainly concerns the housing construction in the USA and Canada. The purpose of this article to contribute to the discussion in the Netherlands on innovation in the building technology, e.g. formulated in the report `Bouwvisie 2010` (Vision on Buildings for the year 2010) of the Dutch Advisory Board Technology Policy for the Building Industry (ARTB, abbreviated in Dutch) and the ...

Energy Technology Data Exchange (ETDEWEB)

The basic principle of the green building philosophy is to design buildings that consider environmental performance. Residential and commercial buildings in Canada consume about 30 per cent of the total secondary energy use and are responsible for approximately 29 per cent of carbon dioxide equivalent greenhouse gas emissions and many other wastes. An optimization model was developed which minimizes life cycle cost and life cycle environmental impact. The model distinguishes different energy sources and incorporates their impacts, such as resource depletion, global warming and acidification. The model also considers design variables such as window type, orientation, building orientation, window-to-wall ratio, wall type and roof type. The model can be used to identify optimum green building designs for given conditions. The model uses ...

Science.gov (United States)

Most K-12 schools could save 25% of their energy costs by being smart about energy. Nationwide, the savings potential is $6 billion. While improving energy use in buildings and busses, schools are likely to create better places for teaching and learning, with better lighting, temperature control, acoustics, and air quality. This brochure, targeted to school facilities managers and business officials, describes how schools can become more energy efficient.

Energy Technology Data Exchange (ETDEWEB)

This book brings together the 103 presentations given at the 2. conference of the international institute of refrigeration (IIF/IIR) about air conditioning in high rise office buildings. The main themes are: design of air conditioning equipment for high buildings; air quality and thermal comfort inside these buildings; constraints and possible improvements of the refrigeration equipment used; energy conservation; fire protection and smokes detection. All themes are presented both on the technical and economical points of view and concern more particularly the buildings of Chinese cities. This publication is available both on the book and CD-Rom forms. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

This final report for the Swiss Federal Office of Energy (SFOE) is one of a series of reports concerning municipal development in various cities in Switzerland. The four city districts involved include Basel (Gundeldinger Feld), Lausanne (Bellevaux), Lucerne (Basel-/Bernstrasse) and Zurich (Werdwies). This paper takes a look at aspects of building ecology. In the four areas, the following building types and projects were examined with respect to their ecology: Basel: conversion of commercial premises to a community centre, Lausanne and Lucerne: Enhancement of residential areas, Zurich: a new residential building. Criteria examined include general building ecology, building materials, raw materials, toxic substances, recycling, maintenance and deconstruction, energy for heating and hot water, grey energy, electricity, ...

Energy Technology Data Exchange (ETDEWEB)

The manual enhances and simplifies the work of those architects and engineers whose practice includes the analysis and modification of existing buildings to reduce both fuel consumption and operating costs. A review of the principles of energy use and conservation is given. The manual also provides a step-by-step methodology for assessing and improving the year-round energy performance of buildings, as well as a series of forms, charts, and nomographs designed to serve as day-to-day tools in the energy professional's toolbox. After a cost-benefit analysis is prepared for each conservation opportunity, the owner will be able to implement decisions based on projected energy savings and calculate investment costs, operational changes, and payback periods. Each of these considerations is accorded a detailed treatment.

Energy Technology Data Exchange (ETDEWEB)

This report provides a detailed description of, and the baseline assumptions and simulation results for, the building prototype simulations conducted for the building types designated in the Work Plan for Demand-side Management Assessment of Hawaii`s Demand-Side Resources (HES-4, Phase 2). This report represents the second revision to the initial building prototype description report provided to DBEDT early in the project. Modifications and revisions to the prototypes, based on further calibration efforts and on comments received from DBEDT Staff have been incorporated into this final version. These baseline prototypes form the basis upon which the DSM measure impact estimates and the DSM measure data base were developed for this project. This report presents detailed information for each of the 17 different building prototypes developed for use with the DOE-21E program (23 ...

Wastenet

may be possible to meet those loads with renewable energy systems &mdashachieving zero-net- energy performance.Solar-thermal heating systems, ...p/p Spencer and others argue that renewable energy systems should be considered only after the building envelope ...energy loads are brought low enough, however, a renewable energy system may make sense financially. p

Energy Technology Data Exchange (ETDEWEB)

In June 2009, the State of Hawaii enacted an Energy Efficiency Portfolio Standard (EEPS) with a target of 4,300 gigawatt hours (GWh) by 2030 (Hawaii 2009). Upon setting this goal, the Hawaii Clean Energy Initiative, Booz Allen Hamilton (BAH), and the National Renewable Energy Laboratory (NREL), working with select local stakeholders, partnered to execute the first key step toward attaining the EEPS goal: the creation of a high-resolution roadmap outlining key areas of potential electricity savings. This roadmap was divided into two core elements: savings from new construction and savings from existing buildings. BAH focused primarily on the existing building analysis, while NREL focused on new construction forecasting. This report presents the results of the Booz Allen Hamilton study on the existing building stock of Hawaii, along with conclusions on the key ...

Energy Technology Data Exchange (ETDEWEB)

The German voluntary standard 'Passivhaus' (passive house) leads to buildings with practically no energy consumption. The first residential buildings of this type were built in 1998 and the first tertiary buildings in 2000. Such a passive house must fulfill 5 efficiency criteria: annual space heating needs {<=} 15 kWh/m{sup 2}, U{sub v} envelope coefficient lower than 0.15 W/(m{sup 2}.K), U{sub v} of openings lower than 0.8 W/(m{sup 2}.K), airtightness {<=} 0.6 volume/hour, and total energy needs (space heating, hot water, ventilation, lighting and domestic uses) measured at the meter lower than 42 kWh/m{sup 2}.year. This article makes a status of the effective efficiency of existing passive buildings both in the residential and tertiary sectors and presents some possible ways of improvement. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

This paper describes the challenges involved in the construction of a mid-rise housing development in Boston, Massachusetts, during which the development team elected to upgrade the initial design criteria from Minimum Building Code to Energy Star and Leadership in Energy and Environmental Design (LEED) certification. The various constraints imposed on the development were discussed, including constraints imposed by the involvement of substantial public funds as well as the constraints imposed by various funding sources that were approached to leverage energy efficiency and green building investment via competitive grant solicitations. Building owner and utility cost management priorities were outlined along with details of central mechanical system selection. Issues concerning isolation and compartmentalization were examined along with indoor pollution source ...

Energy Technology Data Exchange (ETDEWEB)

The national energy research programme LVIS-2000: Future Building Services is concerned with the control of energy use and indoor climate in buildings of the future. The projects were presented at a one day seminar arranged by the Laboratory of Heating and Ventilation of the Technical Research Centre in Finland which is coordinating the programme. The presentations at the seminar were: Impurity emission from materials, Building materials and indoor air quality, analysis of organic compounds in indoor air, effect of the return air, effect of the return air on health and comfort, electric heating as an indoor climate factor, calculations of air flows in ventilated rooms, effect of energy saving measures on hospital hygiene, application of modern aerosol measurement technique on indoor climate research.

Energy Technology Data Exchange (ETDEWEB)

This case study illustrates how an existing building can be transformed into a sustainable, green facility through teamwork. This multi-purpose building comprises office space, combustion testing facilities, and microwave communications center. The paper discusses internal systems design, indoor air quality, commissioning, economics, operations and maintenance, and monitoring.

Energy Technology Data Exchange (ETDEWEB)

Since many years, people take care of hazardous consequences of a non controlled economic growth and the sustainable development concept gains on one. This situation leads to consequences in the building industry and in the energy policy: buildings insulation in consideration, demand of consultants. In this framework, the partnership between Gaz De France and CICF has to be built. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

Capturing the Daylight Dividend conducted activities to build market demand for daylight as a means of improving indoor environmental quality, overcoming technological barriers to effective daylighting, and informing and assisting state and regional market transformation and resource acquisition program implementation efforts. The program clarified the benefits of daylight by examining whole building systems energy interactions between windows, lighting, heating, and air conditioning in daylit buildings, and daylighting's effect on the human circadian system and productivity. The project undertook work to advance photosensors, dimming systems, and ballasts, and provided technical training in specifying and operating daylighting controls in buildings. Future daylighting work is recommended in metric development, technology development, testing, training, education, and ...

Energy Technology Data Exchange (ETDEWEB)

Science and technology are at the heart of everything we do at the National Renewable Energy Laboratory, as we pursue innovative, robust, and sustainable ways to produce energy--and as we seek to understand and illuminate the physics, chemistry, biology, and engineering behind alternative energy technologies. This year's Research Review highlights the Lab's work in the areas of alternatives fuels and vehicles, high-performing commercial buildings, and high-efficiency inverted, semi-mismatched solar cells.

International Nuclear Information System (INIS)

In this paper, the authors describe the characteristics of design seismic input motions and recently observed seismic records of base isolated buildings in Japan. First, we describe some seismic design spectra for building structures which were adopted. Then we show response spectra and energy spectra of observed records obtained during two recent major earthquakes (The 1995 Hyogo-ken Nanbu Earthquake and the 2003 Tokachi-oki Earthquake), which demonstrate the effectiveness of base isolation against large amplitude earthquake ground motion. We also introduce the responses of base isolated buildings during some earthquakes including the Tokachi-oki Earthquake. These data were gathered through questionnaires sent to many engineers who had conducted response observations of base isolated buildings. Last, an example of a base isolated building on soft ground is ...

Energy Technology Data Exchange (ETDEWEB)

Good indoor air quality and thermal comfort, as well as low energy consumption, were achieved in an environment friendly experimental METOP-office building in Espoo, Finland. The consumption of heating and cooling energy was minimized by installation of energy-efficient windows, good CFC-free thermal insulation of the building envelope, the individually-controlled ventilation and room temperatures, heat recovery and energy-storing structures. According to the study carried out in 1990-1993, the heating energy was 13 kWh/m{sup 3}, 60% lower than the average consumption. The index of the satisfaction of thermal comfort was over 90%. Concentrations of all the measured indoor air pollutants were low. Ventilation rates could be chosen in each office room from 10 to 40 dm{sup 3}/s. The noise level of the ventilation system was low and the lighting ...

Energy Technology Data Exchange (ETDEWEB)

In the United Kingdom several educational buildings were built in the last decades with a strong environmental ethos, real icons of a new generation of low-energy sustainable buildings. For some of the buildings the performance was assessed. Also in the Netherlands several new concepts were developed for sustainable schools during the last years. This is an interesting topic as many of those schools had problems concerning energy efficiency, indoor air quality and thermal comfort. In the case of sustainable schools much effort was put into the design process of the schools to try to find better solutions to face the problems of the traditional designs. This resulted in different solution concepts, which raises the question which are better school concepts. From the literature three evaluations from the UK and one overview of five sustainable educational ...

Energy Technology Data Exchange (ETDEWEB)

To study CdZnTe as a high energy resolution gamma ray detector with a novel new design, and to build a detector array from the new detector design

Energy Technology Data Exchange (ETDEWEB)

A self contained continuous power generation system as described at INTELEC 1979, was successfully commissioned and put into service in a major communications centre at Cardiff in Wales. The objective was to provide all telecommunications equipment and electrical building engineering services from a dual fuel enginegenerating plant, and to recover waste heat energy to heat or cool the building. The plant, which is fully automatic, comprises five 1300kW engines using natural gas or diesel oil, and associated waste heat boiler and chiller systems. This paper reviews the functioning of the plant during its first three years of operation.

Energy Technology Data Exchange (ETDEWEB)

The application of multi-objective genetic algorithms for green building design in two phases were presented in order to better help designers in the decision-making process. The purpose is to minimize two conflicting criteria: the life-cycle cost and the life-cycle environmental impact. Environmental impact criteria examined include energy and non-energy natural resources, global warming, and acidification. Variables focus on building envelope-related parameters. The application of multi-objective genetic algorithms is divided into two phases. The first phase intends to help designers in understanding the trade-off relationship between the two conflicting criteria. The second phase intends to refine the performance region that is of the designer's interest. The results after the two-phase application of the multi objective genetic algorithm were then presented. 13 refs., 4 tabs., 3 figs.

Science.gov (United States)

This is the first of a series of monthly reports summarizing the status of the work of the National Accelerator Laboratory. This first report will cover developments since the publication of the Design Report in January. Authorization hearings were held before the Joint Committee on Atomic Energy on February 21, 1968. Dr. Wilson described the plans and designs of the Laboratory. The present plan of the Laboratory is that the Village of Weston will be utilized for office, laboratory, and shop space during construction. The Laboratory business office is already occupying several houses. The linac section is occupying three houses for offices and construction of an 8,000 sq ft laboratory building for linac work is almost complete. Another house is being used and a 4,500 sq ft inflatable building is being constructed for model-magnet and vacuum testing. Other temporary buildings will be constructed for use ...

Energy Technology Data Exchange (ETDEWEB)

The awareness of health issues related to buildings has heightened past decades. Indoor Environmental Quality (IEQ) has been addressed in most Green Building Rating Systems nowadays. This article analyses the scope of IEQ (Indoor Environmental Quality) within Rating Systems GPR Gebouw, BREEAM-NL (Dutch version of Building Research Establishment's Environmental Assessment Method) and LEED (Leadership in Energy and Environmental Design). Each Rating System allocates health aspects. However, none of these Rating Systems addresses a complete set of relevant aspects. High ratings do not guarantee healthy buildings. It is concluded that, in general, credits for energy efficiency do not interfere with credits for enhanced indoor environmental quality. [Dutch] Gezondheidsaspecten van gebouwen hebben afgelopen decennia steeds meer en integraler aandacht ...

Energy Technology Data Exchange (ETDEWEB)

This article comments on the fact that there are only 17 energy-from-waste installations in operation in the U.S. and in this respect it lags behind other industrialized nations. Explanations for this gap include the relatively inexpensive garbage disposal as landfill, operating difficulties of some early plants and the high cost of building such facilities. There has been a recent push to build resource-recovery plants and it is believed that chemical companies will probably buy energy products from such plants. Hooker Chemical Co's new energy-from-waste plant at Niagra Falls, N.Y. is described, other companies involved in resource-recovery projects are mentioned, and it is hoped that more companies will invest in such plants.

Energy Technology Data Exchange (ETDEWEB)

The contribution outlines the current status of the building construction projects for the German Bundestag in Berlin. The following subjects are discussed: Energetic quality of the building, energy supply concept, integrated energy supply system, electric CHP systems, cogeneration (vegetable oil), aquifer storage (heat storage, cold storage), solar energy (photovoltaic energy conversion, thermal solar energy use), economic and ecological aspects. (HW) [Deutsch] Der vorliegende Beitrag gibt einen Ueberblick ueber den aktuellen Stand des Bauvorhabens des Deutschen Bundestages in Berlin. In diesem Zusammenhang wird auf folgende Themen eingegangen: Energetische Gebaeudequalitaet, Energieversorgungskonzept, Energieverbund, stromgefuehrte BHKWs, Kraft-Waerme-Kopplung (Pflanzenoel), Aquiferspeicher (Waermespeicher, Kaeltespeicher), ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this document is to make a state-of-the-art of the techniques of heating-cooling ceilings and cold beams. These systems offer many advantages: they generate a high quality thermal comfort, they are energy efficient, and offer important room saving, particularly interesting in the case of building renovation. The document comprises 5 parts dealing with: 1 - the heating-cooling ceilings; 2 - the cold beams; 3 - the elements necessary for the dimensioning (building-system interactions, ventilation, temperature regulation and safety systems); 4 - dimensioning method; 5 - design, realization and operation: the rules to follow. (J.S.)

British Library Electronic Table of Contents (United Kingdom)

In Korea, the Proton Engineering Frontier Project (PEFP) is building a proton linear accelerator facility with energy up to 100MeV and a beam current of 20mA. In this study, a radiation field after shutdown in the accelerator facility of the PEFP was evaluated for the purpose of the radiation shielding by using MCNPX code. A facility modeling was performed for the accelerator tunnel building, accelerator chain, target rooms and beam experiment hall. And radiation source terms were evaluated in the facility. With this facility, model and radiation source terms, the concentration of 41Ar was evaluated and the cooling time satisfying regulation in Korea was calculated.

Energy Technology Data Exchange (ETDEWEB)

The main objective of the present study is twofold: (i) to analyze thermal loads of the geothermally and passively heated solar greenhouses; and (ii) to investigate wind energy utilization in greenhouse heating which is modeled as a hybrid solar assisted geothermal heat pump and a small wind turbine system which is separately installed in the Solar Energy Institute of Ege University, Izmir, Turkey. The study shows 3.13% of the total yearly electricity energy consumption of the modeled system (3568 kWh) or 12.53% of the total yearly electricity energy consumptions of secondary water pumping, brine pumping, and fan coil (892 kWh) can be met by using small wind turbine system (SWTS) theoretically. According to this result, modeled passive solar pre heating technique and combined with geothermal heat pump system (GHPS) and SWTS can be economically preferable to the conventional space heating/cooling systems ...

Energy Technology Data Exchange (ETDEWEB)

The overall aim is to develope programme modules for a Danish integrated computer system for projecting buildings and to ensure that Danish programmes are compatible with international systems. The programmes to be integrated here were AutoCAD and SCRIBE-models and the simulation programme tsbi3 for the calculation of indoor climate conditions, power demand and energy consumption in buildings. For the calculation of humidity and temperature conditions in constructions a certain amount of integration is carried out with the MATCH programme (Moisture And Temperature calculations for Constructions of Hygroscopic materials). The activities embodied in the pilot projects are described in this working report in addition to the individual computer programmes and prototypes, and examples and diagrams are presented. The programmes included are a geometry programme for the calculation of areas, lengths and volumes, a programme for ...

Energy Technology Data Exchange (ETDEWEB)

This book applies the Los Alamos Solar Load Ratio (SLR) method to the design of passive solar heating systems, with an emphasis on the average annual heating energy consumption. Recommendations are given on minimizing heating energy consumption by appropriate choices of conservation level and solar system parameters. Analytical methods and supporting tables are presented which enable simple, fast estimates of the heating energy consumption as part of the design process. Topics considered include SLR correlations, the load collector ratio (LCR) method, sensitivity data, cooling considerations, conservation formulas, design procedure, life-cycle costs, high-mass direct gain buildings, low-mass sun-tempered buildings, sunspaces, off-reference night insulation, correlation equations, and mixed systems.

Energy Technology Data Exchange (ETDEWEB)

Pumped storage plants (PSP) supply up to several GW of power and several ten GWh of capacity. Short start-up times and low start-up costs predestine PSP for the control energy market. Grid charges for PSP endanger the further integration of renewable energy and lead to higher electricity supply costs. Therefore, an amendment of legislation is urgently required. Requirements for building large PSP are met at numerous sites in the low mountain ranges of Germany. (orig.)

Energy Technology Data Exchange (ETDEWEB)

PNNL, with cofunding from the Bonneville Power Administration (BPA) and Building Technologies Program, conducted a research and development activity targeted at addressing the energy efficiency goals targeted in the BPA roadmap. PNNL investigated an integrated heating, ventilation and air conditioning (HVAC) system option referred to as the low-lift cooling system that potentially offers an increase in HVAC energy performance relative to ASHRAE Standard 90.1-2004.

Energy Technology Data Exchange (ETDEWEB)

Visits were made to selected manufacturing units with 25 or more employees. Information was gathered on energy consumption and advice was given on the opportunities available for improving the efficiency of energy use. Potential energy savings are estimated and recommendations are made on the action that should be taken to improve the efficiency of energy use. In the footwear industry space heating controls, improvements in boiler plant and steam services along with building insulation provide most of the savings potential. In the leather industries major energy saving opportunities can be found in low-temperature drying, and heat recovery, where the use of heat pumps could contribute substantial savings in drying and process water heating. Boiler controls and good housekeeping are areas where firms can make worthwhile savings at very little capital cost. (MCW)

Energy Technology Data Exchange (ETDEWEB)

This paper presents a technical feasibility study project for the large scale rooftop photovoltaics (PV) grid connected system at Charoenphol-Rama I green building super store of TESCO LOTUS (TL) in Thailand. The objective of this project is (i) to study the technical feasibility of installation 350 kWp PV systems on the top of the roof in this site (ii) and to determine the energy produce from this system. The technical factors are examined using a computerized PVS 2000 simulation and assessment tool. This super store building located in Bangkok, with latitude 14 N, longitude 100 E and the building direction is 16 from North direction. The building roof area is 14,000 m2; with 3 degree face East and 3 degree face West pitch. Average daily solar energy in this area is approximately 5.0 kWh. The study team for this project consists of educational institution as ...

Energy Technology Data Exchange (ETDEWEB)

The indoor climate of school buildings have been much debated recently. Many problems connected with air quality and thermal comfort are caused by bad maintenance, fitted carpets and no sunshades. Mechanical ventilation in schools has gained a bad reputation and many municipalities are seeking other solutions when building new schools. Natural ventilation according to the ''Swedish model'' does not use air filters or heat recovery from the outgoing air and achieve low energy consumption by reducing the airflow substantially in cold weather. Most of the naturally ventilated schools have supply air culverts of concrete below ground outside the building and in the basement. This is also true of schools using hybrid ventilation, where natural and mechanical ventilation is combined. The naturally ventilated schools often use manual control of the ventilation, which may not ...

British Library Electronic Table of Contents (United Kingdom)

Concrete is the primary material for building envelopes in some parts of the world, and its ability to store heat as well as its dynamic temperature changes will not only affect the deterioration rate of the exterior wall but will also greatly influence the energy efficiency of interior air conditioning. There are many methods for measuring the inner temperature of concrete, but they often have limitations, such as indirect estimation, cable installation requirements, high cost, or heterogeneity of the sample structure. In order to measure the internal temperature of concrete, this study integrated a Radio Frequency Integrated Circuit (RFIC) with a temperature sensor chip and embedded the device in concrete structures. A Smart Temperature Information Material (STIM) was thus developed. Thi...

Energy Technology Data Exchange (ETDEWEB)

As the 20th century draws to a close, both individual countries and the world community face challenging problems related to the supply and use energy. These include local and regional environmental impacts, the prospect of global climate and sea level change associated with the greenhouse effect, and threats to international relations in connection with oil supply or nuclear proliferation. For developing countries, the financial cost of providing energy to provide basic needs and fuel economic development pose an additional burden. To assess the magnitude of future problems and the potential effectiveness of response strategies, it is important to understand how and why energy use has changed in the post and where it is heading. This requires study of the activities for which energy is used, and of how people and technology interact to provide the energy services that are desired. ...

Energy Technology Data Exchange (ETDEWEB)

The field of ion acceleration to higher energies has grown rapidly in the last years. Many new facilities as well as substantial upgrades of existing facilities have extended the mass and energy range of available beams. Perhaps more significant for the long-term development of the field has been the expansion in the applications of these beams, and the building of facilities dedicated to areas outside of nuclear physics. This review will cover many of these new developments. Emphasis will be placed on accelerators with final energies above 50 MeV/amu. Facilities such as superconducting cyclotrons and storage rings are adequately covered in other review papers, and so will not be covered here.

Energy Technology Data Exchange (ETDEWEB)

Geothermal heat pump systems are a promising new energy technology that has shown rapid increase in usage over the past ten years in the United States. These systems offer substantial benefits to customers and utilities in energy (kWh) and demand (kW) savings. The purpose of this study was to determine what existing monitored data was available mainly from electric utilities on heat pump performance, energy savings and demand reduction for residential, school, and commercial building applications. Information was developed on the status of electric utility marketing programs, barriers to market penetration, incentive programs, and benefits.

Energy Technology Data Exchange (ETDEWEB)

In front of the risks linked with the increase of the greenhouse gas emissions in the atmosphere, the decision makers must take into consideration first, the scientific advice of climatic change experts, and second, the considerable inertia of the climatic system. Thus, any action implemented so far will have an impact all along the 21. century and later whatever the future human activities. The aim of this memento is to sensibilize the decision makers about the possible consequences of their choice in terms of volume of greenhouse gases and of medium- and long-term evolution: 1 - stakes, role of local decision-makers (greenhouse effect and climatic change, France's international commitment, stakes, liabilities of local decision makers, decentralization laws, local plans of fight against greenhouse effect, public information and dialogue); 2 - urbanism and transports (urban displacements, alternatives to individual cars, collective transportation systems, parking, inter-region ...

Energy Technology Data Exchange (ETDEWEB)

The school building complex Waterland in The Hague, Netherlands, was built with a hybrid ventilation system. The indoor environment and energy consumption were monitored for one year. Air quality and thermal comfort are of a high quality and the consumption of energy for heating is circa 35% lower than normal. The Waterland project was one of eight demonstration projects, carried out within the framework of the ECBS-Annex 35: Hybrid ventilation in New and retrofitted Office Buildings. ECBS stands for the IEA-program Energy Conservation in Buildings and Community Systems. [Dutch] In ECBCs-annex 35 (ECBS staat voor het IEA-programma Energy Conservation in Buildings and Community Systems) is uitgebreid onderzoek gedaan naar hybride ventilatiesystemen in kantoren en scholen. Dit project heeft geleid tot acht internationale ...

International Nuclear Information System (INIS)

This paper reports on pumped storage plants which have become an effective way for some utility companies that derive power from hydroelectric facilities to economically store baseload energy during off-peak hours for use during peak hourly demands. According to the Electric Power Research Institute (EPRI) in Palo Alto, Calif., 36 of these plants provide approximately 20 gigawatts, or about 3 percent of U.S. generating capacity. During peak-demand periods, utilities are often stretched beyond their capacity to provide power and must therefore purchase it from neighboring utilities. Building new baseload power plants, typically nuclear or coal-fired facilities that run 24 hours per day seven days a week, is expensive, about $1500 per kilowatt, according to Robert Schainker, program manager for energy storage at the EPRI. Schainker the that building peaking plants at $400 per kilowatt, which run a few ...

Energy Technology Data Exchange (ETDEWEB)

There are certain factors to take into account when determining the suitability of a healthy house site. Power lines, agricultural spraying, vehicle exhaust, and industrial pollution are all potential sources of indoor air contamination. It is recommended that a environmental assessment be done to determine whether there are specific sources of contamination. Good drainage is required. The surrounding landscaping should be open and sunlit, and with low maintenance requirements. Decks and fences made from pressure-treated or chemical treated lumber should be avoided. One of the early decisions in the design process is the choice of the structural system. The key with all foundation types is to control moisture, whether from rain, from the ground, or the condensation of moisture from the air with cooling. The construction frame is sealed away from the occupants by the air/vapor barrier, so only in extreme cases is it essential to use alternatives to softwood lumber for framing exterior ...

International Nuclear Information System (INIS)

A statistical survey is conducted of air pollution in the city of Rome (Italy) due to conventional building space heating systems burning fossil fuels. The survey identifies the annual consumption of the different fuels and the relative amounts of the various pollutants released into the atmosphere by the heating plants, e.g., sulfur and nitrogen oxides, carbon monoxide, etc. Comparisons are then made between the ratios of urban heating plant air pollutants produced per tonne of fuel employed and those for ENEL (Italian National Electricity Board) coal, oil and natural gas fired power plants, in order to demonstrate the better environmental performances of the utility operated energy plants. The building space heating system energy consumption and pollution data are then used in a cost benefit analysis favouring the retrofitting of conventional heating systems with heat pump systems to obtain ...

Energy Technology Data Exchange (ETDEWEB)

Because of good thermal insulation of advanced energetic buildings and their good airtightness the air hygiene is insufficient. A normal ventilation behaviour by window opening consumes too much heating energy. A calculation method is shown taking into account a required air change number, flow rate and indoor air quality as thermal comfort in the rooms occupied by different number of persons. (GL)

Energy Technology Data Exchange (ETDEWEB)

This 2001 edition of the guide to UK renewable energy companies examines the geothermal heat pump sector, and discusses the technology involved, installations of geothermal heat pumps, the activity in the UK market with increased interest in UK geothermal heat pump products from abroad, and developments in the building sector. The UK government's increased support for the industry including its sponsorship of the Affordable Warmth programme, and the future potential of ground source systems are discussed.

Energy Technology Data Exchange (ETDEWEB)

Design tools that are currently available for use with microcomputers to assist in designing energy-efficient daylighted buildings are presented. The information presented was gathered as a part of a telephone survey to design tool developer conducted over a six month period. The matrix is but one of five categories of tools. The other four were nomographs, protractors/tables, minis, and main frame computer programs. Information is provided to encourage interested design professionals, educators and students to communicate directly with design tool representatives.

Energy Technology Data Exchange (ETDEWEB)

This paper describes the field performance of air conditioning with an energy pile system, which was applied to the pile foundations of an actual building for the purpose of reducing the cost of the underground heat exchanger. First, the building for both office and residential use, for which a space heating and cooling system using friction piles was installed, was built in Sapporo in December 2000. Second, three tests were carried out to specify the design of a heat exchanger inside the pile, and a U-tube type underground heat exchanger was adopted from the viewpoint of energy efficiency and installation costs. Long-term space heating operation measurements indicated that the seasonal average temperatures of brine returning from the underground and pile surfaces were 2.4 and 6.7 deg C, respectively. The average coefficient of performance for space heating was quite high at 3.9, and the seasonal ...

Energy Technology Data Exchange (ETDEWEB)

This conference provided a forum to discuss advances in the application of bioengineering principles and practices dealing with biological systems for the production of food, bioproducts and energy. The topics of discussion ranged from engineering practices in agriculture, forestry, bioresources, biochemistry and biosystems. The sessions of the conference were entitled: renewable energy; waste management; soil and water; machinery systems; building and storage systems; and bioproducts and food. The conference also featured a workshop on integrated biomass supply and logistics. In addition to 20 posters, the conference featured 67 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

Energy Technology Data Exchange (ETDEWEB)

This article deals with the need for control strategies and control systems in buildings with hybrid ventilation. In this respect, control strategies are methods of keeping certain parameters like temperature, air quality etc within specified limits. A control system is automatic and includes sensors, motors, dampers etc. The article also discusses consequences with respect to thermal comfort, air quality and energy use following selection of control parameters for controlling air masses.

Energy Technology Data Exchange (ETDEWEB)

The Open Software Foundation`s Distributed Computing Environment (OSF/DCE) was originally designed to provide a secure environment for distributed applications. By combining it with Kerberos Version 5 from MIT, it can be extended to provide network security as well. This combination can be used to build both an inter and intra organizational infrastructure while providing single sign-on for the user with overall improved security. The ESnet community of the Department of Energy is building just such an infrastructure. ESnet has modified these systems to improve their interoperability, while encouraging the developers to incorporate these changes and work more closely together to continue to improve the interoperability. The success of this infrastructure depends on its flexibility to meet the needs of many applications and network security requirements. The open nature of Kerberos, combined with the vendor support of ...

Energy Technology Data Exchange (ETDEWEB)

Cooling of residential California buildings contributes significantly to electrical consumption and peak power demand mainly due to very poor load factors in milder climates. Thermal mass can be utilized to reduce the peak-power demand, downsize the cooling systems, and/or switch to low-energy cooling sources. Large thermal storage devices have been used in the past to overcome the shortcomings of alternative cooling sources, or to avoid high demand charges. The manufacturing of phase change material (PCM) implemented in gypsum board, plaster or other wall-covering material, would permit the thermal storage to become part of the building structure. PCMs have two important advantages as storage media: they can offer an order-of-magnitude increase in thermal storage capacity, and their discharge is almost isothermal. This allows the storage of high amounts of energy without significantly changing the ...

Energy Technology Data Exchange (ETDEWEB)

The data center in this study had a total floor area of 8,580 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 440 racks, and was located in a 208,240 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but served by the main building chiller plant and make-up air system. Additionally, it was served by a single electrical supply with no provision for backup power. The data center operated on a 24 hour per day, year-round cycle, and users had all hour full access to the data center facility. The study found that data center computer load accounted for 23% of the overall building electrical load, while the total power consumption attributable to the data center including allocated cooling load and ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the performance analysis on a hybrid air-conditioning system according to the hybrid building energy system of the green building demonstration project in Shanghai, in which a 150 m{sup 2} solar collector is used to power two 10 kW adsorption chillers, a vapor compression heat pump is used to cool air in the evaporating end while the condensing heating at about 80{sup o}C is fully used to regenerate a liquid desiccant dehumidification system. In the hybrid system, the sensible cooling to the air is treated mainly by solar adsorption cooling and vapor compression cooling, whereas the latent heat is treated by the liquid desiccant dehumidification system with regeneration from the condensing heat of the heat pump. The results show that the performance of this system is 44.5% higher than conventional vapor compression system at a latent load of 30% and this improving can be achieved by 73.8% at a 42% latent ...

Energy Technology Data Exchange (ETDEWEB)

A review of current daylighting design tools indicates that over 30 tools are now available, including nomographs, protractors, overlays, and programs for micro-, mini-, and mainframe computers. Computer-based tools allow testing and analyzing of more design alternatives under a wider variety of conditions than was previously practical with slower techniques, but they have not fundamentally changed the information available to the design professional. These tools are applicable to certain limited functions of the design process and do not address the varying information needs of the designer at various points in the design process. We describe a concept for a computer-based building envelope design tool that is structured to overcome many of the limitations of the existing tools. The tool would address daylighting design in the context of the overall building envelope design, covering a range of environmental quality issues in addition to ...

Energy Technology Data Exchange (ETDEWEB)

A review of energy use in Haiti, aimed at identifying possible projects to complement current A.I.D. support for institution building and energy planning within the Ministry of Mines and Energy Resources (MMRE), is presented. Key findings are that: (1) the sugar and manufacturing industries rely heavily on biomass fuels - wood, charcoal, and bagasse (sugar cane residue); and (2) demand for commercial energy and for electricity is growing rapidly despite supply constraints. The report calls for A.I.D. to: initiate a program to reduce biomass consumption (which is causing severe soil erosion and deforestation), especially in the small distilleries called guildives; collaborate with MMRE and the World Bank to develop a detailed workplan to promote energy efficiency in the guildives, focusing on technology development; help MMRE and the private sector to project ...

Energy Technology Data Exchange (ETDEWEB)

Life cycle oriented methods are increasingly used for environmental assessments (EAs) of the built environment. However, many assumptions are made in such assessments, potentially influencing the results and making the assessment more ambiguous. To increase the reliability of EAs, consequences of the assumptions made have to be better understood. Since energy use in the operation and maintenance phase is an important factor decisive for the overall environmental performance of a building, the purpose of this study is to investigate how the selection of heat and electricity mix affects the assessed environmental performance of buildings. It also aims to suggest how to choose heat and electricity data in EAs of the built environment in general. Applying four different modes of electricity production and two different modes of heat production in a case study of three different buildings with different ...

Energy Technology Data Exchange (ETDEWEB)

Low energy buildings promise significant energy savings and help climate preservation by cutting down on annual heating requirements to values below 70 kWh per m{sup 2} dwelling space. It is expected that low energy constructions will become the common standard by the year 2000 as a result of the forthcoming energy saving ordinance. For making the introduction and implementation of this standard successful, practical experience will be essential. For this reason, the state government of Hesse has supported respective pilot projects 1987. In 1989 the funding programme `30 low energy buildings in Hesse` has been established. Consecutively - between 1989 and 1993 - 29 buildings were erected. At first, the thermal quality of the crafted building construction including the ventilation systems was checked. ...

Energy Technology Data Exchange (ETDEWEB)

Improving software for the analysis of fenestration product energy efficiency and developing related information technology products that aid in optimizing the use of fenestration products for energy efficiency are essential steps toward ensuring that more efficient products are developed and that existing and emerging products are utilized in the applications where they will produce the greatest energy savings. Given the diversity of building types and designs and the climates in the U.S., no one fenestration product or set of properties is optimal for all applications. Future tools and procedures to analyze fenestration product energy efficiency will need to both accurately analyze fenestration product performance under a specific set of conditions and to look at whole fenestration product energy performance over the course of a yearly cycle and in the context ...

Environmental Research Database

ObjectivesThe primary aim is to enable China to address its energy and infrastructure issues in a sustainable manner, without hindering economic progress, with the UK benefiting from an enhanced uptake of its technology, knowledge and expertise through enhanced business opportunities and strengthened collaboration with key Chinese Institutions. ~%~~%~Objectives~%~1) To build capacity and capability in technology transfer and knowledge exploitation in Chinese and UK business and industry through practical, [continued...]DescriptionThe Chinese 11th Five-Year Plan considers Sustainable Energy Supply and Sustainable Built Environment as crucial for achieving sustainable development. Recognising the potential benefits, the UK government has actively encouraged international collaborations with China. Two Engineering Schools at Queen's University Belfast (QUB), with internationally recognised research excellence ...

Energy Technology Data Exchange (ETDEWEB)

This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that involves the building of a joint biogas plant serving 60 farmers and industrial companies with an annual processing capacity of 45,000 tons. The plant is to produce biogas to be fed into the gas mains and will not only reduce nutrient loading in a region with an extensive livestock industry but also reduce carbon dioxide emissions by using the gas as a motor fuel. The importance of the project with respect to both the environment and energy policy-making is discussed and the costs involved are examined. Details are presented on the technology used and on the material flows involved. Figures are quoted on energy production. The various biogenic substrates used, such as food wastes, waste oils, cereal wastes and used mushroom substrates, are discussed, as is the use of the solid and liquid outputs of the ...

Energy Technology Data Exchange (ETDEWEB)

The superconducting magnets and associated cryogenic components in A-sector represent the initial phase of installation of the Fermilab superconducting accelerator, designed to accelerate proton beams to energies of 1 TeV. Installation of the magnets, comprising one-eighth of the ring, was completed in December, 1981. Cooldown and power tests took place in the first half of 1982, concurrent with main ring use for 400 GeV high energy physics. The tests described in this paper involved 151 cryogenic components in the tunnel: 94 dipoles, 24 quadrupoles, 25 spool pieces, 3 feed cans, 4 turn-around boxes and 1 bypass. Refrigeration was supplied by three satellite refrigerators, the Central Helium Liquefier, and two compressor buildings. The magnets were powered by a single power supply.

KoreaScience (Korea)

Full Text Available

CERN Multimedia

Small world when building a particle detector prototype, the devil is in the tiny details

Energy Technology Data Exchange (ETDEWEB)

The objective of this paper is to perform an impact analysis of the Interim Storage Cask (ISC) of the Fast Flux Test Facility (FFTF) for a 4-ft end drop. The ISC is a concrete cask used to store spent nuclear fuels. The analysis is to justify the impact force calculated by General Atomics (General Atomics, 1994) using the ILMOD computer code. ILMOD determines the maximum force developed by the concrete crushing which occurs when the drop energy has been absorbed. The maximum force, multiplied by the dynamic load factor (DLF), was used to determine the maximum g-level on the cask during a 4-ft end drop accident onto the heavily reinforced FFTF Reactor Service Building`s concrete surface. For the analysis, this surface was assumed to be unyielding and the cask absorbed all the drop energy. This conservative assumption simplified the modeling used to qualify the cask`s structural integrity for this accident condition.

Energy Technology Data Exchange (ETDEWEB)

A survey has been made in relation with the improvement project intended of energy conservation, and reduction of global warming gas emission at the Bobovdol thermal power plant located in the suburb of Sofia, the capital of the Republic of Bulgaria. The existing Bobovdol power plant having a total capacity of 630 MW with three generators is a coal burning thermal power plant having been used already for 23 to 27 years, hence over-aged. The survey has discussed an improvement project of scrap-and-build type to make the plant a high-efficiency gas combined cycle power plant using gas turbines. The project calls for building 210-MW gas combined power generation facilities having 70-MW gas turbines, one each in three stages in 2007, 2012 and 2017. As a result of the discussions, the fuel consumption reducing rate was found to reach 37.99%, whereas the cumulative energy saving quantity in 41 years will ...

Energy Technology Data Exchange (ETDEWEB)

This document is an executive summary of the colloquium organized by the French syndicate of renewable energies (SER) which took place at the Maison de l'UNESCO in Paris during the national debate on energies organized by the French government in spring 2003. The colloquium was organized around 6 round tables dealing with: the world perspectives and the environmental context of the contribution of renewable energies to the sustainable development (respect of Kyoto protocol commitments, contribution to the security of energy supplies, lack of large scale program of development of decentralized power generation in developing countries, lack of market tools linked with CO{sub 2} emissions, improvement of competitiveness); development of renewable energies in Europe (promotion and sustain in all European countries, obligation of supply and purchase, pricing regulation, European ...

International Nuclear Information System (INIS)

Ground-source heat pump systems (GSHPSs), also referred to as geothermal heat pump systems (GHPSs), have been widely used in residential and commercial buildings for years due to their outstanding energy utilization efficiencies. In this study, an energy and exergy modeling of solar assisted ground-source heat pump systems for residential applications is presented for system analysis and performance evaluation. In this regard, the performance of a solar assisted ground-source heat pump heating system, installed in Solar Energy Institute of Ege University, Izmir, Turkey, is evaluated based on the actual operational data to show how energy and exergy efficiencies values change with the system. The average heating coefficient of performances (as energy efficiencies) of the solar assisted ground-source heat pump (GSHP) unit and the overall system are obtained to be ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a decision approach, and associated computer software tools, for prioritizing and selecting among technology development activities. The approach elicits and then summarizes technology development preferences from stakeholders, and then integrates preferences into a set of funding recommendations. By formalizing the technology review process, the decision approach builds consensus and clarifies the basis for final budget decisions. The software development was conducted jointly by Pacific Northwest Laboratory and Decisions Science Associates, Incorporated. The Underground Storage Tank Integrated Demonstration funded the task; however, the approach should also be valuable to the US Department of Energy Office of Technology Development, the Office of Waste Management, and the Office of Environmental Restoration.

Energy Technology Data Exchange (ETDEWEB)

The High Exposure Facility is a collimated high-level gamma irradiator that is located in the basement of the 318 building. It was custom developed by PNNL back in 1982 to meet the needs for high range radiological instrument calibrations and dosimeter irradiations. At the time no commercially available product existed that could create exposure rates up to 20,000 R/h. This document is intended to pass on the design criteria that was employed to create this unique facility, while maintaining compliance with ANSI N543-1974, "General Safety Standard for Installations Using Non-Medical X-Ray and Sealed Gamma-Ray Sources, Energies up to 10 MeV."

Energy Technology Data Exchange (ETDEWEB)

The purpose of this report is to provide the reader with a basic understanding of Argonne National Laboratory`s current general refuse disposal and material recycling programs, how they were developed, and where they are going. In order to better understand the current situation, a brief description of the facilities past practices is explained. ANL is a multi-program research and development center owned by the U.S. Department of Energy (DOE) and operated by the University of Chicago. Argonne`s primary facilities are on a 1,700 acre site, 27 miles southwest of Chicago. Fifty-seven major buildings house approximately 4,500 employees at the site.

Energy Technology Data Exchange (ETDEWEB)

In 1980, Congress passed the energy security act which created the United States Synthetic Fuels Corporation. This entity was created to serve as a catalyst for the development of synthetic fuels projects by the private sector. Then what happened. Increased exploration in the United States stimulated by relaxation of price controls on oil produced an increase in reserves of these resources. Fuel conservation, combined with a reduced energy demand caused by a recession, significantly reduced our overall energy consumption and curtailed our imports of foreign crude oil. All of these factors combined have reduced the enthusiasm to invest in synthetic fuels plants, in spite of the fact that the difference between surplus and shortage is frighteningly thin. South Africa, compared to the U.S., is a small country. The Sasol Two and Sasol Three projects are equivalent to a U.S. investment of $400 billion, on a country size-by-size ...

Science.gov (United States)

The Energy crisis happens to be one of the greatest challenges we are facing today. In this view, much effort has been made in developing new, cost effective, environmentally friendly energy conversion and storage devices. The performance of such devices is fundamentally related to material properties. Hence, innovative materials engineering is important in solving the energy crisis problem. One such innovation in materials engineering is porous materials for energy storage. Porous electrode materials for lithium-ion batteries (LIBs) offer a high degree of electrolyte-electrode wettability, thus enhancing the electrochemical activity within the material. Among the porous materials, mesoporous materials draw special attention, owing to shorter diffusion lengths for Li+ and electronic movement. Nanostructured mesoporous materials also offer better packing density compared to their nanostructured ...

CERN Document Server

The Baikal Neutrino Telescope has been operating in its NT200 configuration since April, 1998. The telescope has been upgraded in April, 2005, to the 10 Mton scale detector NT200+. It's main physics goal is the detection of signals from high energy neutrino cascades. NT200+ reaches a 3-year sensitivity of 2 \\times 10^{-7}cm^{-2}s^{-1}sr^{-1}GeV for an all-flavor diffuse cosmic E^{-2} neutrino flux for energies 10^2 TeV \\div 10^5 TeV. Desgin and sensitivity of NT200+ are described. NT200+ is forming the basic building block of a future km3-scale (Gigaton-Volume) Baikal Telescope. Research and development work on that next stage detector has started.

Energy Technology Data Exchange (ETDEWEB)

This research report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that examined the feasibility of setting up 'MINERGIE' low-energy-consumption module standards for the production of heat in small residential buildings. The aims of the standards and the basic idea behind the MINERGIE-modules are discussed. The concepts of the modules for heat pumps and wood-fired heating systems and their combination with solar installations are examined, as are their areas of application. The requirements placed on the modules are listed. System concepts, including simple schematics for typical installations, are presented for wood-log, wood-chippings and pellets-fired systems as well as for ground-loop and air-water heat pump systems as well as their solar-aided counterparts. The results of cost-benefit analyses are presented and questions regarding system guarantee and liability are ...

Energy Technology Data Exchange (ETDEWEB)

This study reported on the performance of a passive solar radiant floor heating system designed for standard energy-saving farmhouses in northeast China. Weather data in the region was analyzed in terms of solar radiation, temperature, humidity and light levels. The heating characteristics of the building materials such as windows, doors, walls and roofs were also analyzed along with the indoor thermal environment of the farmhouse. The heating load was then calculated along with the size of the thermal storage element and the area of the collector element. The passive solar radiant floor heating system was designed for heating during the winter and cooling in summer. According to the results, the heating characteristics of the system have the potential to improve farming villages environment and the use of renewable energy.

Energy Technology Data Exchange (ETDEWEB)

Many solutions of General Relativity appear to allow the possibility of time travel. This was initially a fascinating discovery, but geometries of this type violate causality, a basic physical law which is believed to be fundamental. Although string theory is a proposed fundamental theory of quantum gravity, geometries with closed timelike curves have resurfaced as solutions to its low energy equations of motion. In this paper, we will study the class of solutions to low energy effective supergravity theories related to the BMPV black hole and the rotating wave-D1-D5-brane system. Time travel appears to be possible in these geometries. We will attempt to build the causality violating regions and propose that stringy effects prohibit their construction. The proposed chronology protection agent for these geometries mirrors a mechanism string theory employs to resolve a class of naked singularities. (author)

Energy Technology Data Exchange (ETDEWEB)

Vacuum insulation panels (VIP) offer excellent thermal resistance properties that can enhance the energy efficiency of insulating systems, save space and contribute to energy consumption reductions. However, VIPs are not used much in Canada, and new commitments to carbon dioxide reductions has created the need to study the prospect of using VIPs in various components of a building envelope. For that reason, assessment methods for the applicability and sustainability of VIPs for use in building envelope construction were developed. There are practical aspects regarding the long-term performance and application of VIPs in building construction. Air molecules and water molecules can permeate through the foil and seams of the VIPs, causing a reduction in thermal resistance. This paper addresses some of the test methods that may accelerate long term changes in thermal resistance. Results ...

Science.gov (United States)

Embracing the notion of going green, an affluent school district in Pennsylvania spent $83 million as part of the high school's renovation and expansion project. The three-level addition is now equipped with self-dimming lights, energy-efficient windows, a rooftop solar water heater, and a geothermal cooling and heating system. As a bonus for going green, the school district received a $250,000 grant from the Pennsylvania Department of Environmental Protection. The district used that money to create an information center in the lobby of the building where a touch-screen computer provides students, staff, and visitors with data related to the operation of the school's energy-efficient water and electrical systems. The system will graphically depict utility use over the course of a year. The monitoring system and touch-screen computer can turn this school into a living lab, with science, math, and economics teachers using the ...

Energy Technology Data Exchange (ETDEWEB)

Ventilation, cooling and illumination of modern high-rise office buildings with high-quality thermal insulation (average k-value 1.0 W/m12K) and high loads from office machinery (up to 20 W/m12 and beyond) are problematic even for modern facility management systems, with consequences for the building shell, heating system, and window ventilation. [Deutsch] Die Lueftung, Kuehlung und Beleuchtung moderner Buerohochbauten mit extremer Waermedaemmung (mittlerer K-Wert 1,0 W/m{sup 2}K) und hohen Bueromaschinenlasten (bis zu 20 W/m{sup 2} und mehr) verursachen auch heute noch erhebliche Probleme, obwohl die technische Gebaeudeausruestung weiterentwickelt wurde. Dies zeigt sich vor allem bei der Fassadenausbildung der Heizung und Fensterlueftung. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The Pacific Northwest National Laboratory (PNNL) operates a number of research and development (R and D) facilities for the Department of Energy on the Hanford Site. According to DOE Order 5400.1, a Facility Effluent Monitoring Plan is required for each site, facility, or process that uses, generates, releases, or manages significant pollutants or hazardous materials. Three of the R and D facilities: the 325, 331, and 3720 Buildings, are considered major emission points for radionuclide air sampling and thus individual Facility Effluent Monitoring Plans (FEMPs) have been developed for them. Because no definition of ''significant'' is provided in DOE Order 5400.1 or the accompanying regulatory guide DOE/EH-0173T, this FEMP was developed to describe monitoring requirements in the DOE-owned, PNNL-operated facilities that do not have individual FEMPs. The remainder of the DOE-owned, PNNL-operated facilities are ...

Energy Technology Data Exchange (ETDEWEB)

This report addresses a Los Alamos National Laboratory (LANL) proposal to build a pulsed neutron source for simulating nuclear-weapons effects. A point design for the pulsed neutron facility was initiated early in FY94 after hosting a Defense Nuclear Agency (DNA) panel review and after subsequently visiting several potential clients and users. The technical and facility designs contained herein fulfill the Statement of Work (SOW) agreed upon by LANL and DNA. However, our point designs and parametric studies identify a unique, cost-effective, above-ground capability for neutron nuclear-weapons-effects studies at threat levels. This capability builds on existing capital installations and infrastructure at LANL. We believe that it is appropriate for us, together with the DNA, to return to the user community and ask for their comments and critiques. We also realize that the requirements of last year have changed significantly. Therefore, the ...

Energy Technology Data Exchange (ETDEWEB)

The Conference on Building Design and Architecture organized by Swedish Council for Building Research Contents included articles on building physics, thermal-climate technology, indoor-air-quality technology, construction materials, quality assurance, and building policy and regulation.

Energy Technology Data Exchange (ETDEWEB)

This document contains the technical proceedings of the 19 national seminar on the rational use of energy and exposition of equipment and services, organized by the Asociacion de Tecnicos y Pofesionistas en Aplicacion Energetica (ATPAE) (Association of Technicians and Professionals on Energy Application) conducted in Mexico City on September 21-25, 1998. This seminar encompassed subjects such as: energy saving in the energy sector, energy efficiency in industrial processes and practical developments, practical cases of energy saving in industry, energy saving in buildings, transportation, non-renewable energy utilization and environmental impact and eco-energies. [Espanol] Este documento contiene la memoria tecnica del 19 seminario nacional sobre el uso racional de la energia y ...

British Library Electronic Table of Contents (United Kingdom)

A solar-driven 10-ton LiBr/H2O single-effect absorption cooling system has been designed and installed at the School of Renewable Energy Technology (SERT), Phitsanulok, Thailand. Construction took place in 2005, after which this system became fully operational and has been supplying cooling for our main testing buildings air-conditioning. Data on the systems operation were collected during 2006 and analyzed to find the extent to which solar energy replaced conventional energy sources. Here, we present these data and show that the 72m2 evacuated tube solar collector delivered a yearly average solar fraction of 81%, while the remaining 19% of thermal energy required by the chiller was supplied by a LPG-fired backup heating unit. We also show that the economics of this cooling system are domi...

Science.gov (United States)

The most significant lessons provided by these developments at SASOL are the importance of long-range planning and the need for establishing a commercialized technology base in synfuels. These are necessary to reduce our dependence on foreign energy sources and can be accomplished with suitable cooperation between government and private industry and between agencies within the government. The Fischer-Tropsch process is not the only method for producing gasoline from coal, but so far it is the only one commercially proven. Another process, which produces gasoline from methanol, has been considered for commercialization. The government of New Zealand decided in December 1979 to build a commercial-size plant using its abundant natural gas as the feedstock in a natural gas to methanol to gasoline process. Because methanol can also be produced from gasified coal, this process may be an attractive option for the production of gasoline from coal in ...

International Nuclear Information System (INIS)

A survey is given on the results in hand on the natural radioactivity of building materials. It is shown that only a small percentage of building materials has an increased content of radioactive materials. The results are compared with approximate values given in a Russian publication. (orig./AK).

Energy Technology Data Exchange (ETDEWEB)

In the green building of Shanghai Research Institute of Building Science, the evacuated tubular solar collectors with a total area of 150 m{sup 2} were installed to provide heating for the covered area of 460 m{sup 2}. The floor heating coil pipes were made of high-quality pure copper with the dimension of {phi} 12 x 0.7 mm. Under typical weather condition of Shanghai, the average heating capacity was 25.04 kW during the working hours from 9:00 to 17:00, which was sufficient to keep indoor thermal environment. The average electric COP of the floor heating system was 19.76 during the system operation. Compared with the widely used air-source heat pump heating systems with the electric COP of 3.5 in Shanghai, the solar-powered floor heating system shows great potential in energy conservation in winter. With respect to the whole heating period, the solar fraction was 56%. According to the performance analysis of the system ...

Energy Technology Data Exchange (ETDEWEB)

The unsteady state heat transfer behaviour of a vertical wall subject to the effects of uniform radiation is investigated and the dimensional analysis of combined heat transfers by conduction, convection and radiation is presented. The convective heat transfer coefficients used in the numerical model are determined experimentally by means of an assembly resembling the conditions encountered in the dwelling (variable temperatures and heat flows in time and space, wall associated with a floor, radiative flux outside the wall). In routine conditions (homogeneous wall dimensions, temperature differentials less than 40/sup 0/C), it is shown that the problem depends in practice on three parameters (instead of five) and that nomographs can give the energy accumulated in the wall as a function of its geometric and thermal charactersitics and the external conditions (type and thickness of material, changes in incident flux, convection over the height of the wall in laminar, ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the Proceedings of the 1995 Oil Heat Technology Conference and Workshop, held on March 22-23 at Brookhaven National Laboratory (BNL), and sponsored by the U.S. Department of Energy - Office of Building Technologies (DOE-OBT), in cooperation with the Petroleum Marketers Association of America. This Conference, which was the ninth held since 1984, is a key technology transfer activity supported by the ongoing Combustion Equipment Technology (Oil-Heat R&D) program at BNL, and is aimed at providing a forum for the exchange of information among international researchers, engineers, manufacturers, and marketers of oil-fired space-conditioning equipment. The objectives of the Conference were to: (1) Identify and evaluate the state-of-the-art and recommend new initiatives for higher efficiency, a cleaner environment, and to satisfy consumer needs cost-effectively, reliably, and safely; (2) Foster cooperation among federal and ...

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970`s, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on the waste form. The Department of Energy, ...

International Nuclear Information System (INIS)

Full text: The nuclear renaissance, anticipated by AREVA in the beginning of the century is now happening in several countries around the world. The fundamentals being the increasing demand of energy, the volatility of fossil fuel prices, the awareness of climate change threat connected with the extensive use of fossil fuels. The EPRTM reactor present significant improvements compared to previous generation reactors enabling to reach an outstanding safety level (redundancy of safety systems, airplane crash resistance), to improve the economics (extended plant lifetime, flexibility and availability during operation and, increased efficiency and fuel utilization) while limiting the impact on workers and the environment. Several countries have been implementing the transition to third generation reactors. The presentation will analyze different examples in order to draw the lessons learned from this first wave and to set-up the criteria for a successful transition ...

International Nuclear Information System (INIS)

Energy savings from the use of daylighting in commercial buildings are realized through implementation of photoelectric lighting controls that dim electric lights when sufficient daylight is available to provide adequate workplane illumination. The dimming level of electric lighting is based on the signal of a photosensor. Current simulation approaches for such systems are based on the questionable assumption that the signal of the photosensor is proportional to the task illuminance. This paper presents a method that simulates the performance of photosensor controls considering the acceptance angle, angular sensitivity, placement of the photosensor within a space, and color correction filter. The method is based on the multiplication of two fisheye images: one generated from the angular sensitivity of the photosensor and the other from a 180- or 360-degree fisheye image of the space as ''seen'' by the photosensor. The paper includes a detailed ...

Wastenet

...Polymer Fuel Cells Challenge Publications News Events Login Register Search Content type All Web pages Case studies Publications News Video Home ...Buildings Carbon capture & storage Combined heat & power Electricity transmission & distribution Energy storage Fuel cells Geothermal Hydroelectric Hydrogen Industry Lighting Marine Metering Nuclear Solar Transport Wind ...Home Emerging technologies Current focus areas Polymer Fuel Cell Challenge Polymer Fuel Cells Challenge The objective of the Polymer Fuel Cells Challenge is to develop,...prove and commercialise novel polymer fuel cell technologies that have the potential to deliver a step-change in overall system cost. What are ...

Energy Technology Data Exchange (ETDEWEB)

Better quality of thermal comfort as well as reduced heat energy demand and accordingly CO{sub 2} emission can be achieved by better heating and ventilation strategies in private buildings. The paper deals with a novel model-based measurement and automation system. It describes the implementation of better strategies under given technical circumstances. (orig.) [German] Durch Verbesserung der Heizungs- und Lueftungsstrategien im privaten Lebensbereich kann sowohl Heizenergie eingespart und damit die CO{sub 2}-Emission verringert, als auch die Raumbehaglichkeit verbessert werden. Der Beitrag behandelt ein modellgestuetztes Mess- und Automatisierungssystem, mit dem die Realisierung der verbesserten Strategien unter gegebenen technischen Randbedingungen praktisch erst moeglich wird. (orig.)

International Nuclear Information System (INIS)

In Korea, a manufacturing process for the fabrication of CANDU 37-element fuel bundles was successfully developed between 1981 and 1986. At Korea Atomic Energy Research Institute (KAERI), more than 20,000 fuel bundles were produced up to May 1992, for use in Wolsung-1 power reactor. At the time of the conference, about 15,000 of these fuel bundles had been irradiated in Wolsung-1, and almost all of them had performed well. From 1995, the commercial fuel production program will be transferred to Korea Nuclear Fuel Company, which is building a plant with a capacity of 400 tons of uranium per year. So-called CANFLEX fuel, more appropriate to advanced fuel cycles, is being developed jointly by AECL and KAERI. The paper includes a listing of the current status of the Republic of Korea's nuclear power plants, with planning projections up to the year 2006. 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

This guidebook concerns the design of air-conditioning and air-treatment installations in recent and old buildings. The design of indoor atmosphere treatment systems is based on a rigorous and safe methodology. The following aspects are reviewed: situation of ambient air treatment, different aspects of a project, humid-air technique, principles of air treatment, basic conditions for a successful project, determination of enthalpy and hydric loads of rooms, design of ambient treatment systems, cold water production using a thermodynamical system, aeraulics, hydraulics, acoustics, logics of operation, forecasting of energy consumptions, global management of air-conditioning installations, ambient air-treatment systems. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

A number of difficult technical challenges need to be solved in the fields of accelerator and free-electron laser (FEL) technologies in order to build an X-ray FEL. One of the tasks well suited to the Advanced Photon Source Low Energy Undulator Test Line (LEUTL) is to take the intermediate step of solving some of the problems of single-pass FEL operation in the ultraviolet range. The existing Advanced Photon Source (APS) linac, in addition to its role of supply positrons for the APS storage ring, will also be used to generate the particle beam for the LEUTL. Here, the design of the magnetic system for the high gain soft x-ray free electron laser is described.

Energy Technology Data Exchange (ETDEWEB)

The ventilation requirements for decontamination are normally determined with a static calculation method. In some cases, the pollutant emission is intermittent, for example in the car park of an office building, where all the cars enter and leave the place nearly at the same time. Generally, in such a case, the volume of the garage is large, consequently the time constant of the system has a high value. So a static approach would no longer stay accurate and a dynamic evaluation is needed. With the help of some assumptions, calculations remain rather simple and results can be plotted on nomographs or computed on a programmable handheld calculator. The amount of energy saved may appear very large in some cases. A sizing optimization will be required but also remains easy to compute. The paper presents the method of calculation for a single ventilation level and the optimization of a two-level ventilation.

British Library Electronic Table of Contents (United Kingdom)

Greening is a useful mitigation strategy for planners mainly from a visual perspective. For high-density urban living environment such as Hong Kong, urban greening helps cooling the air and providing shade; it also helps lowering building energy consumption by providing a better outdoor boundary condition. Many researchers have also suggested that greening may be employed as a strategy for combating the ill effects of urban Heat Island (UHI). Working towards a set of better greening guidelines for urban planners, the current paper first provides a comprehensive review of planning with urban greening. It then describes parametric studies that have been conducted to investigate the preferred location, amount, and types of vegetation for urban planning. The parametric studies employed the num...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents the work achieved to instrument the ATLAS software framework, ATHENA, with a library of tools and utensils for the physics analysis as well as the extraction of the jet energy scale using physics events (in-situ calibration). The software part presents the various components of the ATHENA framework which handles the simulated and reconstructed data flow as well as the different stages of this process, before and during the data taking. The building of a library of tools easing the reconstruction of physics objects, their association with Monte-Carlo particles and their API is then explained. The need for common language and collaboration-wide utensils is emphasised as it allows to share the workload of validating these tools and to get reproducible physics results. The analysis part deals with the implementation of a light jet energy scale calibration algorithm within the C++ framework. This calibration ...

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

This bibliography contains citations concerning the control and mitigation of radon pollution in homes and commercial buildings. Citations cover radon transport studies in buildings and soils, remedial action proposals on contaminated buildings, soil venting, building ventilation, sealants, filtration systems, water degassing, reduction of radon sources in building materials, and evaluation of existing radon mitigation programs including their cost effectiveness. Analysis and detection of radon and radon toxicity are covered in separate published bibliographies. (Contains 129 citations fully indexed and including a title list.).

Energy Technology Data Exchange (ETDEWEB)

In the construction work for the Unit No.5 Turbine Building at Hamaoka Nuclear Power Station, the collaboration work for the planning and the coordination of the building construction and the machinery installation was carried out utilizing three-dimensional computer aided design (3D CAD) information. It was the first time in Japan for a building constructor and a plant manufacturer to work together, exchanging 3D CAD data of the whole building and adjusting the construction schedule. It was made possible to confirm the correspondence concerning the planning of both companies from the primary stage of the project by the total process simulation and to adjust on-going work precisely by the partial process simulation.

Energy Technology Data Exchange (ETDEWEB)

Recent studies in elementary particle physics have made the need for an e{sup +}e{sup -} linear collider able to reach energies of 500 GeV and above with high luminosity more compelling than ever [1]. Observations and measurements completed in the last five years at the SLC (SLAC), LEP (CERN), and the Tevatron (FNAL) can be explained only by the existence of at least one particle or interaction that has not yet been directly observed in experiment. The Higgs boson of the Standard Model could be that particle. The data point strongly to a mass for the Higgs boson that is just beyond the reach of existing colliders. This brings great urgency and excitement to the potential for discovery at the upgraded Tevatron early in this decade, and almost assures that later experiments at the LHC will find new physics. But the next generation of experiments to be mounted by the world-wide particle physics community must not only find this new physics, they must find out what it ...

Energy Technology Data Exchange (ETDEWEB)

The grant in question, DE-FG03-94ER75954, was awarded to Insights El Paso Science Museum to build key exhibits. These exhibits helped the Museum fulfill its mission to ``promote curiosity and stimulate interest by exploratory, entertaining, exciting, and participatory learning in a broad range of scientific disciplines to persons of all ages regionally and internationally.`` There are several current Board of Directors members who also were Board members during the grant period and who helped construct some of the exhibits. Through speaking with them and reviewing minutes of Board meetings during 1994, it has been determined that seven of the ten proposed exhibits were constructed, with an eighth exhibit constructed as an alternative. Photos of seven of the exhibits and preliminary sketches of some are attached. Following is a list of the constructed exhibits: Hot or Cold, Give and Take, Conduction, Convection, Sources of Energy, Wind ...

Energy Technology Data Exchange (ETDEWEB)

Work of the Geothermal Heat Pump Consortium (GHPC), a joint program of the US Department of Energy, the US Environmental Protection Agency, the US electric utilities and industry was described. The consortium was established to improve energy efficiency and reduce CO{sub 2} emissions by moving ground source and groundwater source heat pumps from niche products to ten percent of the new and retrofit HVAC market in less than a decade. The GHPC program focuses on : (1) reducing first costs through technology innovation and innovative financing, (2) strengthening the infrastructure though education, training and work codes and regulations, and (3) building confidence in the technology through demonstrations of cost-effectiveness, low maintenance efforts and through marketing programs. Results of the first two years of operations were described. Results indicate that the objectives are being achieved, the number of installations ...

Science.gov (United States)

The largest solar heating and cooling system undertaken to date is now operating at the George A. Towns Elementary School in Atlanta, Georgia. It is expected to provide more than 60 percent of the building's heating and cooling requirements, using commercially available components and techniques. The Towns project is a United States Energy Research and Development Administration-sponsored experiment. The principal components of the solar heating and cooling system designed for the school--the solar collector array, the existing gas-fired boiler, the absorption chiller, and hot and cold water underground tanks to provide thermal storage--are described. To derive maximum benefit from the experiment, the system is fully instrumented for accurate measurement of performance. Environmental data, including insolation and ambient temperture, humidity, and wind conditions will be recorded. The inlet temperatures, outlet temperatures, and the ...

Energy Technology Data Exchange (ETDEWEB)

Panel cooling of buildings offers energy savings over conventional space-cooling systems. We present a procedure for calculating the performance of H[sub 2]O-LiBr absorption-panel cooling systems, in which the evaporator is the panel itself. Nomographs have been developed for this approach. Under the conditions examined, the H[sub 2]O-LiBr absorption unit operates with a theoretical performance coefficient of about 90% and with a practically constant specific cooling capacity of 2394 kJ/kg H[sub 2]O. For common values of the parameters involved, the panel cooling power varies from 25 to 175 W/m[sup 2] and the cooling water mass-flow through the panel is 40-260 g/m[sup 2]h. The thermal power needed to drive the system varies from 27 to 200 W/m[sup 2] and the associated temperatures from 70 to 100[sup o]C; thus, the system may be operated on solar energy. (Author).

Energy Technology Data Exchange (ETDEWEB)

In 1970, the Federal Power Commission predicted a fall from 46% to 27% in 1990 as a result of predicted increases in the use of nuclear power. Today, the Department of Energy expects coal to supply about 50% of electricity generation in 1990. About one-eighth of the world's annual hard coal production is used to make electricity in the United States. Power stations in the country used more coal in 1979 than was produced in the whole Western Europe that year. These 405,000,000 tons of coal equivalent were burned in 1257 individual utilities with an aggregate capacity of 235,000 megawatts. There are coal-fired power plants in 43 of the 50 states. Four factors will be most important in shaping the future development of coal-based electricity: prices, conservation, environmental regulations, and national security. The price differential between coal and oil has now reached a level where it is much more economic for a United States electric utility to ...

Energy Technology Data Exchange (ETDEWEB)

Pacific Gas & Electric Co.`s (PG&E`s) Delta district, approximately 45 miles northeast of the San Francisco Bay Area, is a fast growing residential community with peak demand occurring between 6 and 7 PM in hot summer weekdays. In the early 1990s, PG&E`s system planners projected a need to build a new substation in 1996 to meet the local peak electricity demand. In 1991, as part of a new distribution planning and capital investment process, PG&E launched its innovative Model Energy Community (MEC or Delta) program to test whether the inclusion of new, experimental rates and geographically-targeted cost-effective energy-efficiency measures could reduce the local peak demand and therefore defer major substation and T&D capital investment. Two new residential TOU rates were designed and implemented in PG&E`s Delta area between 1991 and 1993. This paper discusses the market assessment activities and ...

International Nuclear Information System (INIS)

A spectroscopic study is performed for high spin states of "5"5Fe, "5"5Co and "5"7Ni. To populate the investigated residues with a relevant cross section, the fusion evaporation reactions of "3"0Si("2"8Si, 2pn)"5"5Fe, "3"0Si("2"8Si, 2pn)"5"5Co and "4He("5"4Fe, n)"5"7Ni were chosen. To identify the new #gamma# transitions and to build the energy level schemes, #gamma#-#gamma# coincidence techniques together with excitation functions were employed. Angular distributions and #gamma#-#gamma# angular correlations allowed us to assign the spin values of the nuclear states. The previous level scheme of "5"5Fe is extended into the region between 6.5-11 MeV of excitation energy, up to spin 27/2, while the yrast decay pathos of "5"7Ni and "5"5Co are reported here for the first time. Experimental data are fairly well reproduced by Glaudemans' shell model calculations. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the melting temperature of ...

Energy Technology Data Exchange (ETDEWEB)

The aim of the study was to establish by means of a measuring programme how much energy for space heating can be saved by the installed hybrid system. Further, experience with the systems was to be gathered under practical use conditions. As user behaviour can influence space heating energy consumption to an extent having several times the effect of the contribution of the hybrid system, a fact that is also reported in literature, it is not sufficient to measure only space heating energy consumption. So, a unit in one of the terraced houses was scrupulously measured. In the three other terraced houses, only space heating energy consumption was measured.- This final report contains not only a description of the concepts of the buildings and hybrid system but also the energy consumptions measured, and detailed analyses of the budgets. (orig./AKF) [Deutsch] Mit ...

Energy Technology Data Exchange (ETDEWEB)

In this paper an analysis will be performed to assess the economical competitiveness of Nuclear Power against other base load technologies. There are several plans to build more nuclear power plants in western countries; these plans are result among other things of the fossil fuel high prices and the concern for the global warming. France started the construction of one EPR at Flamanville in 2007 and at the end of 2008 there were 17 applications before NRC for construction and operation licenses (COL) to build as much as 26 new reactor units in USA, among the designs selected are the US-EPR, APWR, ESBWR, ABWR and AP1000. Currently, there is a lot of uncertainty about what is the overnight cost for a new generation III nuclear power plant and the vendors are not providing too much information. However, it is expected that under the new economy conditions the overnight cost will be between 2500 and 3500 USD/kW, the output electricity power of the ...

Energy Technology Data Exchange (ETDEWEB)

The research project's objective is to create a decision help for owners of residential buildings for several families regarding the renewal of decentralized heating and warm water preparation systems in the flats. The focus lies on a comparison of the costs of typical systems on the basis of a full cost calculation. This is done by taking into consideration the intentions of residential building companies like the reduction of additional costs to be paid by the tenants (both for social reasons and to make the flats easier to rent), low investment costs, low maintenance costs, energy saving, tenants' claims for comfort and acceptance by the tenants, economical reasons, especially regarding flats fully amortized (activation in the balance sheet). In addition to the quantitative comparison, the advantages and disadvantages of the different systems were also compared to one another from the qualitative point ...

Energy Technology Data Exchange (ETDEWEB)

A geothermal heat pump-assisted heating system is introduced into Changchun City and a survey is conducted to determine if the system may be popularized in this extremely cold region located in the northeastern part of China. In concrete terms, the hot water that circulates through the office building of Changchun Ground Heat Development Co., Ltd., is switched to hot water prepared by a geothermal heat pump. The test continued from December 2000 to March 2001. It is then concluded that heating by geothermal heat pumps will be fully serviceable to Changchun City. Implemented are (1) the shift from the coal fired boiler system to a geothermal heat pump system comprising 16 subterranean heat exchangers for the heating of the office building which is approximately 1000 m{sup 2} large, (2) long-term monitoring of the operating conditions, (3) measurement of subterranean heat exchanger thermal conductivity and subterranean temperature, and (4) the ...

International Nuclear Information System (INIS)

Ground source heat pumps (GSHPs), often referred to as geothermal heat pumps (GHPs), offer an attractive option for heating and cooling residential and commercial buildings owing to their higher energy efficiency compared with conventional systems. GSHPs have been used for four years in the Turkish market, although they have been in use for more years in developed countries. The purpose of this study is to present an energy and exergy analysis of a GSHP system with a 50 m vertical 1.25 in. nominal diameter U-bend ground heat exchanger. This system was applied to a 65 m"2 room in the Solar Energy Institute, Ege University, Izmir, for the first time at the university level in Turkey. The Institute, built in 1986, has a livable floor area of 3000 m"2 and uses passive solar techniques. The heating and cooling loads of the room studied were 3.8 and 4.2 kW at design conditions, respectively. The system was ...

Energy Technology Data Exchange (ETDEWEB)

The issue of projecting policies ensuring appropriate energy supply in the future has become more important in Germany after conclusion of the agreement on a long-term nuclear power phase-out. A recent comparative analysis of a selection of scientific studies forecasting the implications of a nuclear power phase-out has shown that there is demand for more studies examining the issue in greater detail, and on the basis of an enlarged scope of research topics. Hence the present study, intended as a preliminary analysis, will investigate the potential, conditions of successful application, conceivable support schemes, and effects of those policy options that in any case, apart from the nuclear power phase-out scenario, are of essential importance in the context of building the proper conditions for sustainable development of Germany's energy sector. The options and strategies examined are: stepping up ...

Energy Technology Data Exchange (ETDEWEB)

The following subjects are dealt with: physics of indoor air flow, flow in individual rooms, exchange of air and pollution between individual building zones and with the outside world, thermal coupling with the building shell, thermal comfort and air quality, evaluation of the ventilation. figs., tabs., refs.

Science.gov (United States)

... our architecture. Upon that foundation, we are building a set of web-based information management capabilities. These ...

Science.gov (United States)

... 15, 14, Robert Constable, Cornell University, NY, Building Interactive Digital Libraries of Formal Algorithmic Knowledge, Navy. ...

Wastenet

facilities, building hygienic latrines and introducing regular solid waste collection systems . These methods are constantly being developed and

Science.gov (United States)

... Aluminum electrolytic capacitors have improved through the years. They are smaller, and equivalent series resistance (ESR) is improved. ...

International Nuclear Information System (INIS)

... aluminium 28 building materials cockcroft-walton accelerators copper copper

International Nuclear Information System (INIS)

This work come along of the necessity to utilize an unique High-Energy Electron Linear Accelerator (10 MV) for radiant treatments which require higher doses in the surface levels of tissue. It is analyzed the interposition of acrylic degraders (spoilers) in the beam, especially for opposed and parallel fields in the cases of head and neck. It was analyzed the possible combinations of the following parameters: 1) Field sizes defined at isocenter (100 cm) 6 x 6 cm"2, 8 x 8 cm"2 and 10 x 10 cm"2 ; 2) Surface-spoiler distance (DSS) of 4, 7 and 10 cm; 3) Spoilers with different thickness 1.1 and 1.5 cm. It was observed a displacement of the maximum dose toward the surface, and an increase in the percentile doses in the build-up zone when the spoiler is nearing and/or increasing its thickness. It is verified that the use of spoilers, support the symmetry and plane of the beam inside of the clinically acceptable margins. When the results obtained are ...

International Nuclear Information System (INIS)

The U.S. Department of Energy (DOE) has developed comparatively detailed quality assurance requirements for the high-level radioactive waste disposal systems. Quality assurance is recognized as a key issue for confidence building and smooth implementation of the HLW program in Japan, and Japan is at an initial phase of repository development. Then the quality assurance requirements at site research and site selection, site characterization, and site suitability analysis used in the Yucca Mountain project were examined in detail and comprehensive descriptions were developed using flow charts. Additionally, the applicability to the Japan high-level radioactive waste disposal project was studied. The examination and study were performed for the following QA requirements: The requirements that have the relative importance at site research and site selection, site characterization, and site suitability analysis (such as planning and performing ...

Energy Technology Data Exchange (ETDEWEB)

H Power Enterprises of Canada was founded in 1997; currently, it has 40 employees and expect to grow to about 50 by mid-2000. The company is engaged in fuel cell technology development , manufacturing and marketing. The company has the advantage that its technology has been proven, products are already commercialized, and strategic alliances are already in place to make an assault on the market. The concept of proton exchange membrane fuel cell technology is explained in terms of efficiency, response time, power density, stack manufacturing cost, maintenance cost, stack life and compatible thermal loads. Individual products, their energy and operating efficiency, potential applications and potential markets are reviewed. It is estimated that for stationary fuel cells the market will be worth $ 30 billion by 2030. In the United States alone, remote residential cogeneration sites are estimated at 500,000. The estimates for uses in transportation is estimated at $ 1 ...

International Nuclear Information System (INIS)

Current advanced CMOS source/drain engineering involves the use of amorphizing implants with 3D geometry. Upon annealing, the induced transient enhanced diffusion (TED) can only be accurately predicted if the amorphized region is correctly modeled, as well as the formation and evolution of extended defects, particularly 3 1 1's and dislocation loops. In addition to the extended defects, already modeled in the atomistic kinetic Monte-Carlo simulator DADOS, we have developed a physically based modeling approach for the implant-induced damage build-up, amorphization and recrystallization, suitable to handle device-size process simulation. It is based on amorphous pockets (3D, irregular shape agglomerates of an arbitrary number of interstitials and vacancies, plus trapped impurities) with a size-dependent activation energy for recombination. The model is able to reproduce experimental aspects like the crystal-amorphous transition temperature and ...

International Nuclear Information System (INIS)

The cell's cytoskeleton, providing the cell with structure and shape, consists of a complex array of structural proteins, including microtubules, microfilaments and intermediate filaments. Intermediate filaments play a crucial role in mechanotransduction and in providing mechanical stability to cells, in particular under large deformation. By utilizing molecular simulation, here we report a nanomechanical analysis of vimentin intermediate filament dimers, the basic building blocks of intermediate filaments. We describe a detailed analysis of the mechanical properties and associated deformation mechanisms, and find that mechanical stretch induces a transition from alpha-helices to beta-sheets, a phenomenon known as alpha-beta transition. A comparison of the Young's modulus predicted from simulation with experimental measurements is provided, and good agreement is found. We present an analysis of structural changes during deformation, domain unfolding patterns, rate ...

International Nuclear Information System (INIS)

In partnership with the US Navy, high-technology corporations, and research universities, Jefferson Lab is building a superconducting radio-frequency (SRF) accelerator-driven free-electron laser (FEL) and is outfitting an FEL user facility. This first fourth-generation light source - a 1 kW, 3 #mu#m infrared (IR) laser - is the first step in a program to develop high-average-power SRF-based IR and ultraviolet (UV) FELs for multiple manufacturing applications as well as for defense-related applied research and basic scientific research. This initial FEL will be driven by a 42 MeV, 5 m A recirculating SRF linac similar to the much larger SRF linac in Jefferson Lab's 4 GeV, 200 #mu#A Continuous Electron Beam Accelerator Facility (CEBAF). The FEL is expected to demonstrate 75% energy recovery. Its linac will be cooled by the existing CEBAF cryogenic system. At Jefferson Lab, an infrastructure of facilities and people already supports the advance of ...

Energy Technology Data Exchange (ETDEWEB)

CeO{sub 2} undergoes a first-order phase transition from fluorite to {alpha}-PbCl{sub 2}-type structure under high pressure. To evaluate the changes in physical properties of CeO{sub 2} nanomaterials as the particle size decreasing, high-pressure Raman study under quasi-hydrostatic condition has been performed on CeO{sub 2} nanospheres self-assembled by 5 nm CeO{sub 2} nanoparticles at room temperature. Surprisingly, as the pressure elevate to 34 GPa, the CeO{sub 2} nanospheres still retain the cubic fluorite-type structure, indicating the sample is more stable than the bulk counterpart. Whereas, previous high-pressure studies show the phase transition at 22.3/26.5 GPa for 12 nm CeO{sub 2} nanoparticles, which is less stable than the bulk materials. The enhancement of phase stability might be attributed to the increase of surface energy of CeO{sub 2} nanospheres as the size of the building units decrease. (Copyright copyright 2011 WILEY-VCH ...

Energy Technology Data Exchange (ETDEWEB)

Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly & Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to develop the radioisotope tracer technology, which can be used in solving industrial and environmental problems and to build a strong tracer group to support the local industries. In relation to the tracer technology in 1999, experiments to estimate the efficiencies of a sludge digester of a waste water treatment plant and a submerged biological reactor of a dye industry were conducted. As a result, the tracer technology for optimization of facilities related to wastewater treatment has been developed and is believed to contribute to improve their operation efficiency. The quantification of the experimental result was attempted to improve the confidence of tracer technology by ECRIN program which basically uses the MCNP simulation principle. Using thin layer activation technique, wear of tappet shim was estimated. Thin layer surface of a tappet shim was irradiated by proton beam and the correlation between the measured activity loss ...

Science.gov (United States)

A strategic partnership was formed among the American Foundrymen`s Society and the Federal government to develop and transfer the technology needed by the US foundry industry to: increase energy efficiency of cupola melting; improve recovery of carbon, silicon, and manganese through reduced oxidation losses; and improve productivity due to more uniform and predictable iron compositions. An effective mathematical model of the cupola offers a solution to the complex and interactive chemical and heat transfer processes to melt cast iron. The transient changes in charge size, charge composition, blast rate, and coke rate are used to optimize operation to improve melting rates, minimize oxidation losses of valuable alloying elements (C, Si, and Mn), and maintain iron composition. Despite these challenges, the cupola produces iron at a lower cost, and have better environmental controls than other melting process with 70% of domestic liquid iron produced by this ...

Energy Technology Data Exchange (ETDEWEB)

This paper evaluates a new power tower concept that offers significant benefits for commercialization of power tower technology. The concept uses a molten nitrate salt centralreceiver plant to supply heat, in the form of combustion air preheat, to a conventional combined-cycle power plant. The evaluation focused on first commercial plants, examined three plant capacities (31, 100, and 300 MWe), and compared these plants with a solar-only 100-MWe plant and with gas-only combined-cycle plants in the same three capacities. Results of the analysis point to several benefits relative to the solar-only plant including low energy cost for first plants, low capital cost for first plants, reduced risk with respect to business uncertainties, and the potential for new markets. In addition, the concept appears to have minimal technology development requirements. Significantly, the results show that it is possible to build a first plant with this concept ...

International Nuclear Information System (INIS)

These experiments were performed on the Isocele separator, on-line with the Orsay synchrocyclotron; thulium isotopes were produced by bombarding natural erbium targets with 150nA beam of 157MeV protons. Two Ge(Li) detectors, with resolution of 2.3 and 2.5keV at 1332keV used for #gamma#-ray measurements; conversion electron spectra were measured using a Si(Li) detector. #gamma# spectra, #gamma#-#gamma# coincidence and conversion electron measurements were sufficient to build the flow energy level schemes of the transitional "1"5"8Er and "1"5"6Er nuclei. On both nuclei several quasi rotational bands have been identified. These results are compared with other even erbium isotopes and with the neighboring N=88 and 90 isotones. Comparisons with predictions issued from some classical models are also performed: "1"5"8Er appears as a deformed nucleus very similar to "1"6"0Er and "1"6"2Er; on the other hand "1"5"6Er seems to be a soft vibrational ...

International Nuclear Information System (INIS)

In this study, a probabilistic seismic risk analysis of the Wolsung NPP containment building was performed by a seismic hazard analysis and a seismic fragility analysis based on the nonlinear dynamic time-history analyses. The conventional seismic fragility analysis of the safety related structures in a NPP have been performed by using the linear elastic analysis results. The probabilistic seismic risk of the containment building was 5.19e-8.

Science.gov (United States)

The Defense Advanced Research Projects Agency (DARPA) inaugurated a program addressing research and development for an Exoskeleton for Human Performance Augmentation in FY!2001. A team consisting of Oak Ridge National Laboratory, the prime contractor, AeroVironment, Inc., the Army Research Laboratory, the University of Minnesota, and the Virginia Polytechnic Institute has recently completed an 18-month Phase I effort in support of this DARPA program. The Phase I effort focused on the development and proof-of-concept demonstrations for key enabling technologies, laying the foundation for subsequently building and demonstrating a prototype exoskeleton. The overall approach was driven by the need to optimize energy efficiency while providing a system that augmented the operator in as transparent manner as possible (non-impeding). These needs led to the evolution of two key distinguishing features of this team's approach. The first is the ...

International Nuclear Information System (INIS)

Vacuum glazing consists of an evacuated space between two sheets of glass. Vacuum glazing has a large effect on energy savings in houses and buildings. Vacuum glazing can achieve higher insulating performance than conventional insulated glazing. Nippon Sheet Glass has successfully developed conventional vacuum glazing. In this study we investigated an advanced form of vacuum glazing. Its thermal insulation ability is equivalent to 100 mm thick glass wool thermal insulation. This vacuum glazing contained a SnO_2:F low emissivity surface. The influence of the residual gas in a vacuum space on heat flow is important to performance. For long-term thermal stability, it is very important to maintain vacuum stability. To understand this better, we studied the behavior of outgassing from the inside glass surfaces exposed to an external energy source. We have studied the behavior of outgassing from a glass surface using a Nd:YAG ...

Energy Technology Data Exchange (ETDEWEB)

The Materials & Fuel Complex (MFC) facilities 799 Sodium Processing Facility (a single building consisting of two areas: the Sodium Process Area (SPA) and the Carbonate Process Area (CPA), 799A Caustic Storage Area, and 770C Nuclear Calibration Laboratory have been declared excess to future Department of Energy mission requirements. Transfer of these facilities from Nuclear Energy to Environmental Management, and an associated schedule for doing so, have been agreed upon by the two offices. The prerequisites for this transfer to occur are the removal of nonexcess materials and chemical inventory, deinventory of the calibration source in MFC-770C, and the rerouting and/or isolation of utility and service systems. This report provides a description of the current physical condition and any hazards (material, chemical, nuclear or occupational) that may be associated with past operations of these facilities. This ...

Energy Technology Data Exchange (ETDEWEB)

The Detartment of Energy's National Solar Data Program established solar energy systems in residential and commercial buildings across the United States. These solar sites are linked to Vitro Laboratories Division's computer in the National Solar Data Network (NSDN). Vitro collects and analyzes data from this network to determine the thermal performance of each of the solar systems. Environmental information collected at the sites for the month of August 1980 is presented. The environmental data for the NSDN are presented in the form of tables for each solar site. The solar sites are grouped into 12 zones, each of which consists of several adjacent states. The solar energy sites are in alphabetical sequence within each zone. The tables provide available meteorological data for reporting sites in the NSDN as follows: (1) Insolation: the insolation table presents the total, diffuse, ...

Energy Technology Data Exchange (ETDEWEB)

Green building (GB) is part of the concept of promoting sustainability. Although GB and the concept of sustainability are well studied for environmental concerns, their business rationale and related social concerns have not been fully explored or widely accepted by the parties involved in the building sector. In this study, the situation of GB market in relation to the general building market is reviewed and the business rationales of stakeholders to invest in the GB market have been investigated from the perspective of building designers. In addition, the factors that enhance the popularity of GB have been explored and the obstacles that hinder its market have been examined. The data are collected by a questionnaire survey covering building designers in Hong Kong and Singapore, the cities that are categorized as economically developed cities in Asia. After data analysis of the ...

Energy Technology Data Exchange (ETDEWEB)

The Fermilab Steering Group has developed a plan to keep U.S. accelerator-based particle physics on the pathway to discovery, both at the Terascale with the LHC and the ILC and in the domain of neutrinos and precision physics with a high-intensity accelerator. The plan puts discovering Terascale physics with the LHC and the ILC as Fermilab's highest priority. While supporting ILC development, the plan creates opportunities for exciting science at the intensity frontier. If the ILC remains near the Global Design Effort's technically driven timeline, Fermilab would continue neutrino science with the NOVA experiment, using the NuMI (Neutrinos at the Main Injector) proton plan, scheduled to begin operating in 2011. If ILC construction must wait somewhat longer, Fermilab's plan proposes SNuMI, an upgrade of NuMI to create a more powerful neutrino beam. If the ILC start is postponed significantly, a central feature of the proposed Fermilab plan calls for ...

Energy Technology Data Exchange (ETDEWEB)

Oregon State University (OSU) and the Pacific Northwest National Laboratory (PNNL) were funded by the U.S. Department of Energy to conduct research focused on resolving the key technical issues that limited the deployment of efficient and extremely compact microtechnology based heat actuated absorption heat pumps and gas absorbers. Success in demonstrating these technologies will reduce the main barriers to the deployment of a technology that can significantly reduce energy consumption in the building, automotive and industrial sectors while providing a technology that can improve our ability to sequester CO{sub 2}. The proposed research cost $939,477. $539,477 of the proposed amount funded research conducted at OSU while the balance ($400,000) was used at PNNL. The project lasted 42 months and started in April 2001. Recent developments at the Pacific Northwest National Laboratory and Oregon State University suggest that ...

Energy Technology Data Exchange (ETDEWEB)

The long-term aim of our research is to develop humidification-dehumidification desalination technology for farms in arid coastal regions that are suffering from salt-infected soils and shortages of potable groundwater. The specific aim of our current study was to determine the influence of greenhouse-related parameters on a process, called Seawater Greenhouse, which combines fresh water production with growth of crops in a greenhouse system. A thermodynamic model was used based on heat and mass balances. The dimension of the greenhouse had the greatest overall effect on the water production and energy consumption. A wide shallow greenhouse, 200 m wide by 50 m deep gave 125 m{sup 3} d{sup -1} of fresh water. This was greater than a factor of two compared to the worst-case scenario with the same area (50 m wide by 200 m deep), which gave 58 m{sup 3} d{sup -1}. Low power consumption went hand-in-hand with high efficiency. The wide shallow greenhouse consumed 1.16 kW ...

International Nuclear Information System (INIS)

In Europe, MOX fuel has been supplied by AREVA for more than 30 years, to 36 reactors: 21 in France, 10 in Germany, 3 in Switzerland, 2 in Belgium. For the present and future, recycling is compulsory in the frame of sustainable development of nuclear energy. By 2030 the overall volume of used fuel will reach about 400 000 t worldwide. Their plutonium and uranium content represents a huge resource of energy to recycle. That is the reason why, the European Utilities issued an EUR (European Utilities Requirement) demanding new builds reactors to be able of using MOX Fuel Assemblies in up to 50 % of the core. AREVA GEN3+ reactors, like EPR"T"M or ATMEA"T"M designed with MHI partnership, are designed to answer any utility need of MOX recycling. The example of the EPR"T"M reactor operated with 100 % MOX core optimized for MOX recycling will be presented. A standard EPR"T"M can be operated with 100 % MOX core using an advanced ...

Energy Technology Data Exchange (ETDEWEB)

The proposed ASHRAE/IES Standard 90.1-1989R contains updated requirements for pipe insulation thicknesses developed on the basis of technical and economic principles. These requirements were determined based on computer simulations of the annual energy loss through the insulation, first cost assumptions for the insulation, and economic assumptions of discount rate and energy escalation rate. In later work, the same tools were used to analyze the sensitivity of the cost-effective insulation level for piping insulation to variations in operating hours, ambient temperature, fluid temperature, and economic assumptions. These analyses were carried out using cost data for pipe insulation averaged across several sources. The results of the sensitivity study showed that system operating hours is a critical parameter in determining the cost-effective pipe insulation thicknesses. Although there is a lack of reliable sources of typical operating hour data ...

Energy Technology Data Exchange (ETDEWEB)

A study was conducted to predict indoor ventilation, smoke movement and fire propagation in a new building currently under construction at the Ecole Polytechnique de Montreal. It was conducted in response to concerns regarding the impact that air quality, in normal operation conditions, and smoke concentration, in the event of a fire, may have on occupants of a building. A detailed three-dimensional model of the new building was constructed using the NURBS-based modeler, Rhino. Simulations of fire propagation and airflow ventilation were performed in different areas of the building. The flow pattern data was analyzed using the computational fluid dynamics (CFD) program called FLUENT. It predicted air flow conditions and estimated the mean age of air (MAA) in the room. Real-world geometries, such as diffuser inlets, have a significant impact on overall fluid flow behaviour and are necessary for this type ...

Science.gov (United States)

This Addendum to the Facility Safety Plan (FSP) 360 Complex describes the safety requirements for the safe conduct of all biohazardous research operations in all buildings within the 360 complex program areas. These requirements include all the responsibilities and authorities of building personnel, operational hazards, and environmental concerns and their controls. In addition, this Addendum prescribes facility-specific training requirements and emergency controls, as well as maintenance and quality assurance requirements for ES&H-related building systems.