Energy Technology Data Exchange (ETDEWEB)

A reliable source of specific criteria for recognizing a wetland, as defined for regulatory purposes would be valuable. In 1987 the Army Corps of Engineers developed a technical manual for identifying wetlands (1987 Wetlands Manual). An interagency manual (1989 Wetlands Manual) was later developed. This manual has been used to identify wetlands according to three evidentiary factors: vegetation, hydrology, and soil. This paper addresses the development of criteria to delineate wetlands, and describes some of the logic used by federal courts to uphold the limited constitutional use of the 1989 Wetlands Manual.

Science.gov (United States)

...Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION QUALIFICATION AND CERTIFICATION OF LOCOMOTIVE ENGINEERS Component Elements of the Certification Process § 240.109 General criteria for eligibility based on...

UK PubMed Central (United Kingdom)

Amphibians are considered reliable indicators of environmental quality. In the western United States, a general decline of frog populations parallels an apparent worldwide decline. The factors thought...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

RIFLE criteria have been used to determine the incidence of acute kidney dysfunction (AKD) after orthotopic liver transplantation (OLT). However, no studies have focused on the incidence of AKD after OLT in patients with normal pre-OLT kidney functions. Using the RIFLE criteria, we determined the incidence and risk factors for AKD after OLT in patients with normal pre-OLT kidney function. We retrospectively analyzed the records of 112 patients who underwent OLT from January 2000 to February 2009 with normal prior kidney function. We investigated three levels of renal dysfunction outlined in the RIFLE criteria: risk (R); injury (I); and failure (F). Preoperative, intraoperative, and postoperative variables were collected. AKD occurred in 64 (57%) OLTs with risk, injury, and failure frequenc...

International Nuclear Information System (INIS)

The US Army Engineers Waterways Experiment Station (WES) and US Army Engineer Division, Huntsville (HNDED) have developed general design criteria and specific design review criteria for the earth-mounded concrete bunker (EMCB) alternative method of low-level radioactive waste (LLW) disposal. An EMCB is generally described as a reinforced concrete vault placed below grade, underneath a tumulus, surrounded by filter-blanket and drainage zones. The tumulus is covered over with a low permeability cover layer and top soil with vegetation. Eight major review criteria categories have been developed ranging from the loads imposed on the EMCB structure through material quality and durability considerations. Specific design review criteria have been developed in detail for each of the eight major categories. 63 refs., 13 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

One of the alternative ideas to solve the spent fuel issues, the partitioning and transmutation (P and T) technology has been developed for decades. Moreover, the concept of LILW production from P and T are proposed by Bowman. A PEACER (Proliferationresistant, Environmental-friendly Accident-tolerant, Continuable and Economical Reactor), based on pyrochemical process and Pb-Bi coolant transmutation reactor, has been conceptually designed to be able to convert all PWR spent fuel into low and intermediate level waste for near-surface disposal. In this study, the acceptance criteria for near-surface disposal facility is derived by the methodology for establishment of acceptance criteria. Then acceptable TRU decontamination factor (DF) and LLFP removal efficiency in order to meet acceptance criteria is evaluated.

Energy Technology Data Exchange (ETDEWEB)

Various engine concepts that are in the race to be the dominant bus-engine type five years from now were reviewed. Three types of engines, the Otto cycle (CNG and propane), diesel and DME (dimethyl ether) received most of the attention. Emission standards, engine size and reliability are the main demands on bus engines. Each of these engine concepts were reviewed against these criteria. In terms of emission standards (as measured by the EEV emission limits) Otto cycle engines have the advantage since they are currently in production. Advanced diesel technology is on the prototype level, but not yet in production. DME-engines are still on the testbed, not in the demonstration stage and much less in the production stage. Otto cycle engines also have the most experience with EEV ...

Science.gov (United States)

Description of courses, curriculum and degree program. "Ceramic and materials engineers design, develop, and participate in the manufacture of both standard and new materials intended for use in a wide variety of industries with diverse applications. These range from the semi-conductor to the aerospace and finally to the traditional ceramics industry. The broad scope of industrial responsibilities handled by ceramic and materials engineers requires knowledge in mathematics, science, engineering, and the social sciences, skills in problem solving, engineering analysis, design, and written and oral communication. The baccalaureate program integrates laboratory with classroom experiences to prepare students for life-long learning. Courses covering thermodynamics, kinetics, mechanical behavior, processing and characterization of materials prepare students for careers in industry and/or for graduate school. ...

Energy Technology Data Exchange (ETDEWEB)

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

Energy Technology Data Exchange (ETDEWEB)

Major factors that contribute to maximized impact resistance of semicrystalline engineering polymers include increased matrix molecular weight, minimal rubber glass-transition temperature, and optimal rubber-particle size, which depends on matrix type. Additional constraints are posed by the limitations of available materials and commercial requirements. Expanding the understanding of impact-modified crystalline engineering polymers will further extend their property ranges and utility. This chapter describes the phenomenology of certain factors, illustrates a new technique to measure rubber particle size, and contrasts the fracture mechanisms of poly(butylene terephthalate), nylon 66, and polyacetal. 49 refs., 24 figs.

Science.gov (United States)

The risk of lung cancer associated with diesel exhaust has been calculated from 14 case-control or cohort studies. We evaluated the findings from these studies to determine whether there is sufficient evidence to implicate diesel exhaust as a human lung carcinogen. Four studies found increased risks associated with long-term exposure, although two of the four studies were based on the same cohort of railroad workers. Six studies were inconclusive due to missing information on smoking habits, internal inconsistencies, or inadequate characterization of diesel exposure. Four studies found no statistically significant association. It can be concluded that short-term exposure to diesel engine exhaust (20 years) increases the risk of lung cancer for locomotive engineers, brakemen, and diesel engine mechanics. There is inconsistent evidence on the effects of long-term exposure to diesel exhaust in the trucking industry. There is ...

Energy Technology Data Exchange (ETDEWEB)

The study required by the West German Ministry of Research and Technology (RS 605) for the Committee on 'Future Nuclear Energy Policy' of the 9th German Parliament is concerned with the following main points: 1) Assessment of technical risks from the social aspect; 2) Discussion of terms and quantification of risks; 3) 'Engineering judgment' and 'questionable' methods in the Fast Breeder analysis of the Society for Reactor Safety (GRS); 4) Assessment criteria of potential damage.

Energy Technology Data Exchange (ETDEWEB)

This report considers the effect of pipe-whip restraints and snubbers on the normal operation of piping systems in nuclear power plants. Also considered are the effect of these postulated event devices on reliability, economics, and the exposure of plant personnel to radiation. Field data were gathered from three nuclear power plants that had applied for Operating Licenses. Criteria, design philosophies, and data were obtained from the respective nuclear steam system suppliers, architects-engineers and utilities.

Energy Technology Data Exchange (ETDEWEB)

'The objective of this project is to provide a means to optimize ligand architecture for f-block metal recognition. The authors strategy builds on an innovative and successful molecular modeling approach in developing polyether ligand design criteria for the alkali and alkaline earth cations. The hypothesis underlying this proposal is that differences in metal ion binding with multidentate ligands bearing the same number and type of donor groups are primarily attributable to intramolecular steric factors. They propose quantifying these steric factors through the application of molecular mechanics models. The research involves close integration of theoretical and experimental chemistry. The experimental work entails synthesizing novel ligands and experimentally determining structures and binding constants for metal ion complexation by series of ligands in which architecture is systematically varied. The theoretical ...

CERN Document Server

The nature of the `inner engine' that accelerate and collimate the relativistic flow at the cores of GRBs is the most interesting current puzzle concerning GRBs. Numerical simulations have shown that the internal shocks' light curve reflects the activity of this inner engine. Using a simple analytic toy model we clarify the relations between the observed $ \\gamma $-rays light curve and the inner engine's activity and the dependence of the light curves on the inner engine's parameters. This simple model also explains the observed similarity between the observed distributions of pulses widths and the intervals between pulses and the correlation between the width of a pulse and the length of the preceding interval. Our analysis suggests that the variability in the wind's Lorentz factors arises due to a modulation of the mass injected into a constant energy flow.

Energy Technology Data Exchange (ETDEWEB)

This report aims to address the potential for solid polymer fuel cell (SPFC) systems to be successfully exploited in the combined heat and power (CHP) market. A number of market studies have been undertaken to look at the size and future potential for this CHP market as well as such issues as market forces and geographical locations. This study focuses on a different aspect, that of the technical and commercial requirement together with the development needs. In order to understand how an SPFC system will have to perform, it is first necessary to examine the criteria used to judge the commercial merits of a particular CHP scheme. Issues that must be addressed include: the investment criteria - time to pay back the investment or rate of return on the investment; the influence of external factors such as electricity cost tariffs, fuel price and regulatory requirements; the cost and performance of existing technology; and the ...

UK PubMed Central (United Kingdom)

The effect of potential risk factors for chronic lymphatic leukaemia was evaluated in a case-referent study encompassing 111 cases and 431 randomised referents, all alive. Information on exposure was...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Structural engineering implies four factors particularly relevant to sonics: airborne noise abatement, insulation of plumbing, by-pass insulation and noise absorption (noise abatement). These are exemplified with special regard to methodical and/or product-specific noise pollution abatement measures. Besides, reference is made to DIN standards 4109 providing both engineers with practical advice and pipe fitters or plumbers with concrete examples for application. VDI recommendations 3733 convey essential knowledge of how to properly apply sonic principles in the planning, design and installation of pipes. (BR).

Science.gov (United States)

In an era of unprecedented technological advancement and economic expansion, construction practice continues to evolve but construction education has not changed appreciably since the 1990s. This schism has prompted industry, government, and other key constituents to question the relevancy and efficacy of current programs. The Accreditation Board for Engineering and Technology (ABET) Engineering Criteria 2000 and the American Council for Construction Education (ACCE) emphasizes outcomes over process, and provides an opportunity for stakeholders to help universities define educational goals and objectives and design a curriculum to meet the desired outcomes. While the need for curriculum modification has been acknowledged, the industry position was amorphous and anecdotal and therefore difficult to address. Qualitative methodologies such as formal surveys and structured interviews can be used to capture and quantify industry ...

Energy Technology Data Exchange (ETDEWEB)

Hybrid vehicles have two power supplies as engine and electric motor which are used most efficiently corresponding to objects respectively to attain energy-saving and low pollution. In this paper, factors concerning the fuel economy of hybrid vehicles and potential thereof are examined, and the possibility of reducing fuel cost by half is described. As possible modes of highly efficient hybrid vehicles, series hybrid vehicles (SHEV) of conventional internal combustion engine, parallel hybrid vehicles using EV in combination, series-parallel hybrid vehicles (SPHV), series type fuel cell type vehicles, ceramic engine-turbo compound power generating SPHV as well as SHEV, and ceramics gas turbine engine power generating SHEV are mentioned. 10 refs., 14 figs.

International Nuclear Information System (INIS)

The partial project SR 2039/4 investigates organizational demands and factors of the man-organization interface. Thee study is divided into the sections inventory of rules and guidelines; evaluation of organizational structures and modes of operation, and working out of demand characteristics and evaluation criteria. The objective consists in representing, analyzing and evaluating the efficiency structure of sequence organization, and deriving practice-relevant concept proposals in order to optimize the man-organization interface. In this regard, the working out of control mechanisms for the evaluation of organizational sequences is of considerable importance as a kind of working aid. (orig./DG).

DEFF Research Database (Denmark)

Executive summary 1. Few studies have to date explained consumer attitudes and purchase decisions with regard to genetically engineered food products. However, the increased marketing of genetically engineered food products and the considerable concern that consumers seem to express with regard to the technology call for the development of a theoretical basis for research into these issues. 2. The aim of the paper is to present three models which we have developed to explain consumer attitudes, buying behaviour and attitude change with regard to genetically engineered food products. All three models build on established consumer behaviour theory and on existing and comparable research in the field. 3. Consumer attitudes toward genetic engineering in food products are explained in an attitude model that builds on Fishbein's multiattribute attitude model. The model deviates from Fishbein's model in a ...

Energy Technology Data Exchange (ETDEWEB)

The paper gives a detailed overview of the history of subsidence engineering in South African collieries. Surface displacements resulting from total-seam extraction are discussed, and the important role of local geology is highlighted. It is shown that the differences in subsidence behaviour between South African and European collieries can be attributed to the presence of competent strata in the overburden of South African coal seams. Criteria are given for the prediction of the most important subsidence parameters, and a new model for the simulation of surface subsidence above total-extraction panels is introduced. The final section of the paper deals with the damage to surface structures caused by total-seam extraction. A brief summary of the most important undermining experiments in South African collieries is given, and it is concluded that local experiences of damage compare with those in Europe. 32 refs., 9 figs., 3 tabs.

International Nuclear Information System (INIS)

This paper provides information on heat transfer enhancement due to jet mixing inside a cylindrical enclosure. The work addresses conservative heat transfer assumptions regarding mixing and condensation that have typically been incorporated into passive containment design analyses. The current research presents an interesting possibility for increasing decay heat removal of passive containment systems under combined natural and forced convection. Eliminating these conservative assumptions could provide the basis for a change of containment design and reduce the construction cost. It is found that the ratio of forced- and free convection Nusselt numbers can be predicted as a function of the Archimedes number and a correlated factor accounting for jet orientation and enclosure geometry. To use the small-scale tests for large containment design, scale-up methods and criteria are important for matching the key governing parameters and fluid ...

Energy Technology Data Exchange (ETDEWEB)

In many applications, the experimenter has limited options about what factor combinations can be chosen for a designed study. Consider a screening study for a production process involving five input factors whose levels have been previously established. The goal of the study is to understand the effect of each factor on the response, a variable that is expensive to measure and results in destruction of the part. From an inventory of available parts with known factor values, we wish to identify a best collection of factor combinations with which to estimate the factor effects. Though the observational nature of the study cannot establish a causal relationship involving the response and the factors, the study can increase understanding of the underlying process. The study can also help determine where investment should be made to control input ...

Energy Technology Data Exchange (ETDEWEB)

This paper consists of two parts. Part 1 deals with the thermodynamic and thermoeconomic methodology of a trigeneration (TRIGEN) system with a rated output of 6.5 MW gas-diesel engine while the application of the methodology is presented in Part 2. The system has been installed in the Eskisehir Industry Estate Zone in Turkey. Thermodynamic methodology includes the relations and performance parameters for energy and exergy analysis, while thermoeconomic methodology covers the cost balance relations, cost of products and thermodynamic inefficiencies, relative cost difference and exergoeconomic factor. (author)

Energy Technology Data Exchange (ETDEWEB)

A micro-mechanistic understanding of bone fracture that encompasses how cracks interact with the underlying microstructure and defines their local failure mode is lacking, despite extensive research on the response of bone to a variety of factors like aging, loading, and/or disease. Micro-mechanical models for fracture incorporating such local failure criteria have been widely developed for metallic and ceramic materials systems; however, few such deliberations have been undertaken for the fracture of bone. In fact, although the fracture event in mineralized tissues such as bone is commonly believed to be locally strain controlled, until recently there has been little experimental evidence to support this widely held belief. In the present study, a series of in vitro experiments involving a double-notch bend test geometry are performed in order to shed further light on the nature of the local cracking events that precede catastrophic fracture ...

Energy Technology Data Exchange (ETDEWEB)

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for ...

Energy Technology Data Exchange (ETDEWEB)

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, ...

Energy Technology Data Exchange (ETDEWEB)

This report presents an assessment of the potential energy savings that could accrue from the use of alternative fuels in future transportation engines. Alternative fuels are defined in this study as hydrocarbon fuels which possess characteristics that assure user safety and satisfaction, but require less energy to produce than conventional specification fuels produced from the same resource. In particular, the energy requirements for producing such fuels from domestic coal and oil shale resources are examined from the standpoint of their adaptability to engine types having a high potential for achieving significant efficiency gains over existing transportation engines. Incentives for specific types of engine development are identified in terms of energy savings above those obtainable with current specification fuels. While engine research and development incentives historically are ...

Energy Technology Data Exchange (ETDEWEB)

The piston bowl design is one of the most important factors that affect the air-fuel mixing and the subsequent combustion and pollutant formation processes in a direct-injection diesel engine. The bowl geometry and dimensions, such as the pip region, bowl lip area, and toroidal radius, are all known to have an effect on the in-cylinder mixing and combustion process. In order to understand better the effect of re-entrant geometry, three piston bowls with different toroidal radii and lip shapes were investigated using computational fluid dynamics engine modelling. KIVA3V with improved submodels was used to model the in-cylinder flows and combustion process, and it was validated on a high-speed direct-injection engine with a second-generation common-rail fuel injection system. The engine's performance, in-cylinder flow, and combustion, and emission characteristics were ...

British Library Electronic Table of Contents (United Kingdom)

Women who have academic careers in engineering have successfully navigated the social identity threats that prevent many other women from feeling that they belong in science, technology, engineering, and math fields. In this research, we examined what factors may be related to resilience in these academic environments. Female academics in engineering and nonengineering fields watched a fictitious conference video depicting either an unbalanced ratio of men to women or a balanced ratio. Subjective measures of identity threat were collected. Past experience with discrimination, positive experience with female role models, family support, and general social support were associated with a greater sense of belonging to or desire to participate in the conference. These variables all buffered neg...

British Library Electronic Table of Contents (United Kingdom)

There is limited information on the incidence of acute kidney injury (AKI) in patients with traumatic brain injury (TBI) although AKI may contribute to morbidity and mortality. We investigated the incidence of AKI in patients with moderate and severe TBI and the association of AKI with risk factors and outcomes in these patients. We studied all TBI patients over 16 years of age admitted to the two designated trauma hospitals in the state of Victoria, Australia from 1 January to 31 December 2008. Patients were included if they had head trauma and presented with a Glasgow coma scale (GCS) <13. Prospectively collected data from the hospital trauma registries, ICUs, and pathology databases were analyzed retrospectively. Risk injury failure loss end (RIFLE) criteria were used to categorize rena...

International Nuclear Information System (INIS)

Full text.The electric energy demand in Lebanon is estimated to grow at an average of 3-5% per year for the coming 10 years. Such an increase in energy demand is problematic for Lebanon since its economy is almost totally dependent on imported fuel which contributes to 97% of the overall energy requirements. Solar water heaters (SWH) are regarded as the most important element in a long term energy conservation and management strategy for this country, but their promotion is a national issue requiring the participation of many stake holders and decision makers. Additionally, the success of solar energy penetration into the existing energy market is constrained by many factors such as technical and financial limitations, decision criteria and policy instruments. This paper will explore the feasibility of SWH, and will work out, using the Analytic Hierarchy Process technique, a policy to ensure a large scale diffusion of SWH in the energy market

British Library Electronic Table of Contents (United Kingdom)

Reasons for variation in transfusion practice in orthopedic surgery are not well understood. This systematic review identified and appraised the quality of the literature in this area to assess the impact of factors associated with the use of allogeneic red blood cell (RBC) transfusion in orthopedic procedures. MEDLINE and EMBASE databases were searched for relevant English language publications. Articles containing a range of MeSH and text terms regarding ''blood transfusion,'' ''predictors,'' and ''multiple logistic regression'' were retrieved. Articles that focused on patients undergoing orthopedic procedures and that met prespecified inclusion criteria were appraised in terms of potential bias and the appropriateness of statistical approach. A total of 3641 citations were retrieved, an...

Science.gov (United States)

Anaphylaxis is a serious allergic reaction that is rapid in onset and sometimes leads to death. Understanding mechanisms, triggers, and patient-specific risk factors for severe or fatal anaphylaxis is critically important. Diagnosis of anaphylaxis is currently based on established clinical criteria. Epinephrine (adrenaline) is the first-line medication for anaphylaxis treatment and delay in injecting it contributes to biphasic reactions, hypoxic-ischemic encephalopathy, and fatality. Here, we focus on four important areas of translational research in anaphylaxis: studies of potential new biomarkers to support the clinical diagnosis of anaphylaxis, laboratory tests to distinguish allergen sensitization from clinical risk of anaphylaxis, the primary role of epinephrine (adrenaline) in anaphylaxis treatment, and strengthening the overall evidence base for anaphylaxis treatment. PMID:21668849

British Library Electronic Table of Contents (United Kingdom)

Customer churn means the loss of existing customers to a competitor. Accurately predicting customer behavior may help firms to minimize this loss by proactively building a lasting relationship with their customers. In this paper, the application of the factor analysis and the Variable Consistency Dominance-based Rough Set Approach (VC-DRSA) in the customer relationship management (CRM) of the airline market is introduced. A set of "ifthen" decision rules are used as the preference model to classify customers by a set of criteria and regular attributes. The proposed method can determine the competitive position of an airline by understanding the behavior of its customers based on their perception of choice, and so develop the appropriate marketing strategies. A large sample of customers fro...

International Nuclear Information System (INIS)

Geologically estimated natural gas resources are 500 Tcm. With the advance in geological science increase of estimated resources is expected. Natural gas reserves in 2000 have been proved to be around 165 Tcm. As it is known the reserves are subject to two constraints, namely: capital invested in the exploration and drilling technologies used to discover new reserves. The natural gas scarcity factor, i.e. ratio between available reserves and natural gas consumption, is around 300 years for the last 50 years. The new discovery of natural gas reserves has given rise to a new energy strategy based on natural gas. Natural gas utilization is constantly increasing in the last 50 years. With new technologies for deep drilling, we have come to know that there are enormous gas resources available at relatively low price. These new discoveries together with high demand for the environment saving have introduced a new energy strategy on the world scale. This paper presents an ...

International Nuclear Information System (INIS)

Accidents from three main practices: medical applications, industrial radiography and industrial irradiators are used to illustrate some common causes of accidents and the main lessons to be learned. A brief description of some of these accidents is given. Lessons learned from the described accidents are approached by subjects covering: safety culture, quality assurance, human factors, good engineering practice, defence in depth, security of sources, safety assessment and monitoring and verification compliance. (author)

Science.gov (United States)

for? Learn the Issues Science & Technology Laws & Regulations About EPA Contact Us Water: Water Quality Criteria You are here: Water Science & Technology Surface Water Standards &...

Energy Technology Data Exchange (ETDEWEB)

For over 50 years, the Bonneville Power Administration (BPA) has evolved to supply electric power to more than 170 customer utilities and direct service industries across 14,800 miles of high voltage transmission lines. BPA's Office of Engineering provides the planning, development, and engineering for the required expansion, upgrade, and replacement of the transmission system. The purpose of this 10-Year Plan is to present strategies to maintain a reliable energy delivery system within changing public, business, technological, and environmental climates. The issues and trends discussed in this document and our strategies for addressing them provide the background for the Office of Engineering programs and projects. With a budget in the hundreds of millions annually and increasing public concern, we welcome the opportunity to communicate with our customers. In addition to the factors, trends ...

Energy Technology Data Exchange (ETDEWEB)

Changes in the physical and chemical processes during the ignition delay period of a gas-fueled diesel engine (dual-fuel engine) due to the increased admission of the gaseous fuels and diluents are examined. The extension to the chemical aspects of the ignition delay with the added gaseous fuels and the diluents into the cylinder charge is evaluated using detailed reaction kinetics for the oxidation of dual-fuel mixtures at an adiabatic constant volume process while employing n-heptane as a representative of the main components of the diesel fuel. In the examination of the physical aspects of the delay period, the relative contributions of changes in charge temperature, pressure, physical properties, pre-ignition energy release, heat transfer, and the residual gas effects due to the admission of the gaseous fuels are discussed and evaluated. It is shown that the introduction of gaseous fuels and diluents into the diesel ...

UK PubMed Central (United Kingdom)

The importance of designating criteria for diagnosing dementia lies in its implications for clinical treatment, research, caregiving, and decision-making. Dementia diagnosis in Huntington's...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The criterion the study is based on in evaluating environmental risks is the possibility of harmful changes in air, water and soils rather than the harmful environmental impacts these changes are caused by. The two significant criteria, i.e. the evaluated environmental hazards potentials or 'value parameters', and the evaluated damage-to-the-environment probabilities or 'safety parameters', reveal the respective environmental risks or 'risk factors'. These risk factors are classified by 23 environmental risk parameters for differentiation between low-risk and high-aid for pollution abatement measures provided that one fixes acceptance limits for the environmental parameters. As a rule the environmental risks of technical facilities which handle hazardous materials can be evaluated appropriately and the results can be compared. (orig./HSCH).

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to present and evaluate control strategies for adjustment and preservation of air quality, thermal and visual comfort for buildings' occupants while, simultaneously, energy consumption reduction is achieved. Fuzzy PID, fuzzy PD and adaptive fuzzy PD control methods are applied. The inputs to any controller are: the PMV index affecting thermal comfort, the CO{sub 2} concentration affecting indoor air quality and the illuminance level affecting visual comfort. The adaptive fuzzy PD controller adapts the inputs and outputs scaling factors and is based on a second order reference model. More specifically, the scaling factors are modified according to a sigmoid type function, in such a way that the measured variable to be as closer as possible to the reference model. The adaptive fuzzy PD controller is compared to a non-adaptive fuzzy PD and to an ON-OFF one. The comparison criteria are the ...

Energy Technology Data Exchange (ETDEWEB)

A pyrochemical process has been introduced and utilized so that the transmutation of spent PWR fuel in PEACER can produce mainly low and intermediate level waste for near surface disposal. Major radioactive nuclides from PEACER pyroprocessing are composed of TRU and LLFP. In this study, the requirement for the final waste from PEACER is evaluated based on the methodology for establishment of waste acceptance criteria. Also, sensitivity analysis for several input parameters is conducted in order to determine acceptable decontamination factor (DF) and LLFP removal efficiency and to find out input parameter that extremely have an effect on DF. As a result of the study, LLFP removal efficiency, especially Sr-90 and Tc-99, is proved to be a major nuclide which contributes to annual dose by human intrusion scenario rather than TRU DF. More than 98.5% of LLFP have to be removed to meet below dose constraint within the DF more than 5.0E + 03. Besides, ...

Science.gov (United States)

... Civil Engineering Page 2. ... 4. TITLE AND SUBTITLE Transforming Civil Engineering (Air Force Civil Engineer, Volume 15, Number 1, 2007) 5a. ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this 3.5 year project is to develop a commercially competitive vehicle powered by ethanol (or ethanol blend) that can meet California`s ultra-low emission vehicle (ULEV) standards and equivalent corporate average fuel economy (CAFE) energy efficiency for a light-duty passenger car application. The definition of commercially competitive is independent of fuel cost, but does include technical requirements for competitive power, performance, refueling times, vehicle range, driveability, fuel handling safety, and overall emissions performance. This report summarizes a system design study completed after six months of effort on this project. The design study resulted in recommendations for ethanol-fuel blends that shall be tested for engine low-temperature cold-start performance and other criteria. The study also describes three changes to the engine, and two other changes to the vehicle to improve ...

Energy Technology Data Exchange (ETDEWEB)

Simple frameworks have been developed for estimating the utilization potential of: (a) solar photovoltaic (SPV) pumps; (b) windmill pumps; (c) producer gas based dual fuel engine pumps; and (d) biogas based dual fuel engine pumps for irrigation water pumping in India. The approach takes into account factors such as: solar radiation intensity, wind speed, availability of bovine dung and agri-residues, and their alternative uses, ground water requirements for irrigation and its availability, affordability, and propensity of the users to invest in renewable energy devices, etc. SPV pumps are estimated to have the maximum utilization potential in India, followed by windmill pumps. (author)

Energy Technology Data Exchange (ETDEWEB)

An overview of climatic factors and impact relative to river ice engineering and science is presented. An explanation of the fundamentals of climatic change is followed by a review of direct and indirect climatic influences that govern river ice breakup and related trends. Known responses of river ice to climatic change and potential future changes to ice breakup processes are described along with the probable ecological and socio-economic consequences of these changes. Changes in engineering approaches to accommodate the present ice regime and predicted changes in climatic variables that affect river ice processes and reduce the vulnerability of infrastructure and ecosystems to climatic change are examined. Future research on the links between river ice and stream ecology is suggested to identify ecological concerns that may result from changes in river ice regimes induced by climatic change. 60 refs., 3 figs.

Energy Technology Data Exchange (ETDEWEB)

In January 2001, Husky Oil Operations Limited (Husky), in joint-venture with Petro-Canada submitted a Development Application (DA) to the Canada-Newfoundland and Labrador Offshore Petroleum Board (C-NLOPB) for the White Rose Development. This DA was prepared following the Canada-Newfoundland Atlantic Accord Implementation Act and the Canada-Newfoundland and Labrador Atlantic Accord Implementation Newfoundland and Labrador Act. In December 2001, the C-NLOPB approved the White Rose DA. This document outlined a proposed amendment to the original Development Plan involving an expansion of its White Rose Development in the Jeanne d'Arc Basin on the Grand Bank. The expansion will consist of a subsea tie-back to the Floating Production, Storage and Offloading (FPSO) vessel through the existing Southern Glory Hole (SGH) and utilizing a new glory hole constructed approximately 4 km south of the SGH. The document presented an overview of the development; geology, geophysics and ...

Energy Technology Data Exchange (ETDEWEB)

number of technical requirements and performance criteria can drive stellarator costs, e.g., tight tolerances, accurate coil positioning, low aspect ratio (compactness), choice of assembly strategy, metrology, and complexity of the stellarator coil geometry. With the completion of a seven-year design and construction effort of the National Compact Stellarator Experiment (NCSX) it is useful to interject the NCSX experience along with the collective experiences of the NCSX stellarator community to improving the stellarator configuration. Can improvements in maintenance be achieved by altering the stellarator magnet configuration with changes in the coil shape or with the combination of trim coils? Can a mechanical configuration be identified that incorporates a partial set of shaped fixed stellarator coils along with some removable coil set to enhance the overall machine maintenance? Are there other approaches that will simplify the concepts, improve access for ...

Energy Technology Data Exchange (ETDEWEB)

There are two kinds of uncertainties in safety assessment of engineering structures. One is of the nature of randomness, and the other fuzziness. Fuzzy uncertainties exist in defining certain structural performances, conditions, parameters, and their interrelationships. The theory of fuzzy sets should be employed to cope with the fuzzy uncertainties. In this paper, a general definition for structural failure considering the fuzzy uncertainties is introduced firstly. Failure of the structure is modelled by a fuzzy event, and described by the membership function. The limit state surface is then replaced by a fuzzy limit state zone, in which every point represents a state belonging to the failure with a certain degree of membership. Then a fuzzy optimization problem for solving the reliability index is formulated. In classical structural reliability theory, the reliability index is defined by the minimum distance from the limit state surface to the origin of the ...

Energy Technology Data Exchange (ETDEWEB)

Biocatalytic Desulfurization (BDS) represents an alternative approach to the reduction of sulfur in fossil fuels. The objective is to use bacteria to selectively remove sulfur from petroleum and middle distillate fractions, without the concomitant release of carbon. Recently, bacteria have been developed which have the ability to desulfurize dibenzothiophene (DBT) and other organosulfur molecules. These bacteria are being developed for use in a biocatalyst-based desulfurization process. Analysis of preliminary conceptual engineering designs has shown that this process has the potential to complement conventional technology as a method to temper the sulfur levels in crude oil, or remove the recalcitrant sulfur in middle distillates to achieve the deep desulfurization mandated by State and Federal regulations. This paper describes the results of initial feasibility studies, sensitivity analyses and conceptual design work. Feasibility studies with various crude oils ...

Wastenet

criteria which would constitute environmentally sound management of mobile phone waste in accordance with the Basel Convention;

Science.gov (United States)

Background: Anxiety disorders are known to be common in the general population. Previous studies with adults with intellectual disabilities (IDs) report a prevalence of general anxiety disorder ranging from less than 2% to 17.4%. Little is known about associated factors in this population. This study investigates point prevalence of anxiety disorders and determines the factors independently associated with them. Methods: Information was collected with 1023 adults with IDs who participated in a large-scale, population-based study. All had a comprehensive physical and mental health assessment. The point prevalence of anxiety disorders according to different diagnostic criteria was determined, as were independently associated factors by using logistic regression analysis. Results: Three point eight per cent (95% CI = 2.7-5.2%) of the cohort had an anxiety disorder at the time of assessment. Generalised ...

Energy Technology Data Exchange (ETDEWEB)

The Energy Laboratory of the University of Houston has developed a computer simulation program called CREAM (Cavity Radiation Exchange Analysis Model) for application to the solar central receiver system. CREAM contains a geometric configuration factor generator based on Nusselt's method. A formulation of Nusselt's method provides the basis for a FORTRAN subroutine NUSSELT. Numerical results from NUSSELT are compared to analytic values and values from Sparrow's method. Sparrow's method is based on a double contour integral and its reduction to a single integral which is a approximated by Gaussian methods. Nusselt's method is adequate for the intended engineering applications, but Sparrow's method is an order of magnitude more efficient in many situations.

Energy Technology Data Exchange (ETDEWEB)

Industrial facilities offer a wide variety of design challenges to engineers, including the mechanical engineers who design the HVAC, the process, exhaust, and other required mechanical systems; the mechanical contractors who install and maintain the systems (and who also may do design work); and the owners` engineers who are responsible for the day-to-day operation of their facilities. Along with the responsibility to see that all systems function as intended is the responsibility to ensure that all worker health concerns are addressed. These include heat stress avoidance and the proper control of harmful substances. The services of industrial hygienists may be required to ensure this. These may be independent consultants or the staff members of mechanical design firms. In addition, it is not unusual for major corporations that own manufacturing plants to have staff industrial hygienists. The accompanying sidebar presents ...

Energy Technology Data Exchange (ETDEWEB)

In the 80's, because of the oil crisis, the Natural Gas (NG) appeared as a fuel with a great potential for Diesel replacement in Heavy Duty Vehicles. At that time, PETROBRAS with other companies have developed partial conversion technologies from Diesel to NG, known as 'Dual Fuel'. Engine dynamometer and vehicle bus tests have been developed to verify its technical and economical viability. Because of several factors, the Dual Fuel Program did not advance and the experience was interrupted. At the same time, other experiences using NG Otto Cycle bus engines, manufactured in Brazil, have been conducted, mainly at Sao Paulo, nevertheless, without expansion. Currently, factors as increase of the NG converted light vehicles fleet; the NG excess in the National Market, which has contributed to the NG distribution net expansion; the Environmental Legislature in vigor, that ...

Science.gov (United States)

We proposed and numerically investigated the influence of spatial symmetry on the terahertz frequency region response of composite planar metamaterials based on deformed split ring resonators. Compared with the original simple structures, the composite metamaterials with different spatial symmetries exhibited exotic electromagnetic properties. The electromagnetic response of a specific configuration with C4 symmetry was identical to the structure with simple lattice. Especially, for configurations with broken symmetry, very sharp Drude-like resonances with high quality factor were observed. The electric field and current distribution associated the resonances were analyzed for deep understanding of the underlying physical properties.

British Library Electronic Table of Contents (United Kingdom)

There is increasing pressure to operate laboratory facilities in environmentally and financially sustainable ways. A key factor in achieving this goal is careful consideration of how energy is used by the buildings' ventilation system, both for conditioning air supplied to the laboratories and the energy used moving air through the building. Traditionally, laboratory energy use is treated as an engineering concern within the scope of the building's overall design and operation. However, this approach limits the involvement of key stakeholders in many important decisions and can lead to unexpected safety concerns for the laboratory's users. We believe that a broad view of the parties affected by a laboratory building's operations is necessary to avoid having the various stakeholders working...

Energy Technology Data Exchange (ETDEWEB)

Since the integrity of the containment penetrations was confirmed under accident management (AM) conditions in the former test, failure criteria tests and aerosol trapping tests were carried out using low-voltage modules and flange gaskets of an actual plant under severe accident (SA) conditions, without AM. The safety margin for failure temperature of the penetrations and the credit for fission product (FP) aerosol trapping effect along the leakage paths of the degraded penetrations were evaluated in the present tests. Failure temperature of the penetrations ranged from 270 to 300degC for low-voltage modules and 300 to 350degC for flange gaskets under 0.4 to 1.0 MPa conditions. Pressure dependency on failure temperature was small. This means that the safety margin of failure temperature under AM condition is more than 70degC. By introducing a equivalent leak area for the damaged test pieces, total leak area was estimated which was smaller than the value used in ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical capacitor devices described in this report were deliverables from the US Department of Energy--Idaho Operations Office (DOE-ID) Contract No. DE-AC07-92ID13404 as part of the US Department of Energy`s (DOE) High Power Energy Storage Program. The Idaho national Engineering and Environmental Laboratory (INEEL) has responsibility for technical management, testing, and evaluation of high-power batteries and electrochemical capacitors under this Program. The DOE has developed various electrochemical capacitors as candidate power assist devices for the Partnership for a New Generation of Vehicles (PNGV) fast response engine requirement. This contract with Maxwell Energy Products, Inc. (Maxwell) was intended to develop a high-energy-density, high-power-density ultracapacitor that is capable of load leveling batteries in electric vehicles. The performance criteria for this device are delivery of 5 W {center_dot} ...

Science.gov (United States)

PMID:6840598

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

This article provides an historical look at how programs and practices for students with emotional or behavior disorders (E/BD) have been evaluated since 1964, leading to a codified, although not universally recognized, set of recommendations for evaluating best practices for students with E/BD set out by The Peacock Hill Working Group (1991). The authors contend that, in addition to the programmatic features of best practice, the addition of the quality indicators and standards for research in special education add a critical dimension for examining the quality of the scientific research of identified best practices. Taken together, these set of recommendations and quality indicators represent the state of the art in program evaluation for best practice and programs for students with E/BD. The goal of this article is to outline the current recommendations and apply them to current behavior intervention practices to identify how well the field is meeting the ...

International Nuclear Information System (INIS)

Central Nervous System (CNS) involvement, whether primary by the Human Immunodeficiency Virus - HIV - itself, or secondary (toxoplasmosis or lymphoma) is remarkably frequent in AIDS, in 40 to 70% of cases, depending upon the author. In order to study the natural history of this illness, a cohort of 25 asymptomatic seropositive patients have been established. Every 6 months these patients undergo biological and clinical examinations, as well as Magnetic Resonance brain scans. After two examinations at a 6 month's interval, the first results are reported. Out of these 25 cases, 9 present anomalies: One patient with diffuse cerebral atrophy and 8 others with high signal intensity areas on T2 weighted sequences, like those of the Multiple Sclerosis. No relationship could be demonstrated between the existence of these lesions and various criteria such as age, sex, risk factors and T4 cells count. The nature of these lesions is not lear. They ...

International Nuclear Information System (INIS)

Many pump reliability problems in the Nuclear Power Plants (NPPs) are being attributed to the operation of the pump at flow rates well below its best efficiency point(BEP). Generally, the manufacturer and the user try to avert such problems by specifying a minimum flow, below which the pump should not be operated. Pump minimum flow usually involves two considerations. The first consideration is normally termed the 'thermal minimum flow', which is that flow required to prevent the fluid inside the pump from reaching saturation conditions. The other consideration is often referred to as 'mechanical minimum flow', which is that flow required to prevent mechanical damage. However, the criteria for specifying such a minimum flow are not clearly understood by all parties concerned. Also various factor and information for computing minimum flow are not easily available as considering for the pump manufacturer' proprietary. The objective of this study ...

Energy Technology Data Exchange (ETDEWEB)

A Lawrence Livermore National Laboratory (LLNL) Management Pre-Start Review (MPR) Team was formed to independently verify the operational readiness of Building 368 (B368) Biosafety Level III (BSL-3) Facility to conduct research with biological pathogens and toxins including those considered Select Agents. Review objectives and criteria were developed from the DOE/NNSA and LLNL requirements. These were provided in the Implementation Plan for the Biosafety Level III (BSL-3) Facility Management Pre-Start Review (BSL-3 MPR) at Lawrence Livermore National Laboratory that was reviewed and approved by DOE/NNSA-LSO. The formal part of the LLNL MPR for the BSL-3 Facility was begun in August of 2005 but work on the MPR was stopped in October of 2005 due to the need for LLNL to reassess organizational and operational controls and respond to Centers for Disease Control and Prevention inquiries related to a shipping incident involving select agents. The MPR was restarted in ...

Science.gov (United States)

Overview  Package   Class  Use  Tree  Deprecated  Index  Help   PREV CLASS   NEXT CLASS FRAMES    NO FRAMES SUMMARY:  INNER | FIELD | CONSTR | METHOD DETAIL:  FIELD | CONSTR | METHOD gov.nih.nci.dc.database Class SearchCriteria java.lang.Object |

UK PubMed Central (United Kingdom)

Primary peritoneal pregnancy has been reported and debated for almost a century. Case reports using Studdiford's criteria and later modified criteria have substantiated the entity, but the pathogenesis...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Traditional two-phase flow-regime criteria based on the gas and liquid superficial velocities may not be suitable to the analyses of rapid transient or entrance flows by the two-fluid model. Under these conditions, it is postulated that direct geometrical parameters such as the void fraction are conceptually simpler and therefore more reliable parameters to be used in flow-regime criteria than the traditional parameters. From this point of view, new flow-regime criteria for upward gas-liquid flow in vertical tubes have been developed considering the mechanisms of flow-regime transitions. These new criteria can be compared to existing criteria and experimental data under steady-state and fully developed flow conditions by using relative velocity correlations. The criteria showed reasonable agreements with the existing data for atmospheric air-water flows. Further ...

International Nuclear Information System (INIS)

This paper describes Automatic Refueling Planning System (ARPS) for a nuclear power station using Genetic Algorithms (GA) and a Simulated Annealing (SA). ARPS has been developed and verified by applying to the Fugen nuclear power station (NPS), which is a 165MWe, heavy water-moderated, boiling light water-cooled, pressure tube-type reactor developed by JNC utilizing mainly uranium and plutonium mixed oxide (MOX) fuel. Fuel loading patterns have been managed independently in the Fugen NPS since the initial core. A planning of an adequate fuel loading pattern on each operational cycle needs one to two months even for expert core management engineers, for the reason that it has multi-objective optimization and nonlinear problems. In order to achieve the optimum fuel loading pattern and a fuel cost reduction, ARPS has been developed by JNC and CRC Solutions Corporation for the last five years. ARPS firstly generates several thousand fuel loading patterns with GA at ...

Science.gov (United States)

with full-scale component test data, a final requirement for completing general materials selection criteria. It also should be pointed out that, ...

Science.gov (United States)

PMID:20173351

Energy Technology Data Exchange (ETDEWEB)

Swirling flow in a direct injection diesel engine was measured by a laser doppler velocimeter. Piston cavity diameter and top clearance volume were changed as factors affecting swirling flow to study the distribution of swirling flow speed. When using the same intake port and changing the opening ratio of piston cavity, the distribution of swirling flow speed was different by the cavity during intake process but these agree just after opening intake valve and then become again different by cavity. When increasing top clearance and decreasing compression ratio, the axial symmetry of flow during commpression process increases. When changing piston cavity, and also when changing intake port, the mean swirling ratio in inside and outside areas of combustion chamber has common tendency to increase and decrease respectively. The mean swirling flow in the combustion chamber may be capable to be predicted by devising a model which can describe this ...

Energy Technology Data Exchange (ETDEWEB)

LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level {alpha} solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination ...

Energy Technology Data Exchange (ETDEWEB)

The further optimisation and improvement of the efficiency of internal combustion engines require the realisation of new technologies leading to a distinctively faster warm-up behaviour of the coolant and lubricants as well as of the engine components after a cold start. In order to achieve reduced fuel consumption and exhaust gas emissions with the help of heat management, the design criteria of innovative cooling systems need to be reflected and adapted to future requirements. The use of intelligent components within the cooling system, such as the 'Stand Alone Rotary Valve' as a thermostat's substitute or the use of coolant pumps with a rotary valve integrated into the pump's inlet chamber, offer new ways to realise in a decisively quicker and more flexible way the appropriate heating up and cooling down procedures at varying driving conditions. A description of both of the intelligent ...

Energy Technology Data Exchange (ETDEWEB)

Turret moored Floating Production Storage and Offloading (FPSO) systems are considered suitable for a wide range of environmental conditions but experience of designing moorings for these units in harsh environments is limited. Furthermore, each floating production system has its own requirements as to the way the riser system is operated because of its dependence on both reservoir and site specific conditions. The current mooring codes do not have a consistent set of requirements; for example, the intact mooring system safety factors range from 1.5 to 2.3. Such vastly differing requirements result in wide variability in the intrinsic safety, reliability and cost. This paper describes a reliability analysis carried out for the first North Atlantic FPSO (Foinaven), to address the acceptance criteria for moorings by returning to the fundamentals. Although the analysis deals with FPSO`s, the approach is applicable to any catenary moored unit. One ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this investigation was to simulate a machining front from an abrasive waterjet and its movements in a ceramic material. Wear factors affecting the abrasive waterjet nozzle were also to be established. Therefore, a low inclination angle (9[degree]) was used between the nozzle and test sample, simulating a moving machine front. A standard nozzle with an inner diameter of 0.76 mm was used in the test, and it was placed close to the samples. The outer diameter of the abrasive nozzle was 9.5 mm. The high wear rate from abrasive waterjets makes it possible to machine hard ceramics-including dense alumina, titanium boride, silicon nitride, and composites-at high machining speeds.

Energy Technology Data Exchange (ETDEWEB)

This paper outlines an approach to develop estimates of individual customer contestability using a combined statistical and engineering analysis. The approach is targeted for use for mid-size commercial and industrial customers who are not being considered for individual flexible pricing contracts. Contestability is defined as the potential lost revenue associated with customers leaving the utility or significantly reducing electricity purchases. Contestability is modeled from the customer`s perspective using a two-stage decision process. In the first stage, the customer decides if he will continue to purchase electricity from the utility (referred to as customer retention), and in the second stage, the customer determines the amount of electricity purchased (referred to as load retention). Measures of individual customer contestability will be key factors in developing market segments and new rate offerings in future energy markets.

Energy Technology Data Exchange (ETDEWEB)

Using gasoline as an example of additives for cold start improvement, fuel vapor composition of methanol-gasoline mixtures, fuel evaporation rate in consideration of temperature drop due to heat of fuel evaporation, air fuel ratio, stoichiometric air fuel ratio and excess air ratio of fuel vapor were calculated. The mixture formation of methanol-gasoline mixtures at low temperature in otto cycle engines was studied. Van Laar's empirical formula was used to estimate the partial pressure of high-percentage methanol blends. It was found that the most part of fuel vapor is occupied by gasoline, even when a small amount of gasoline is added to methanol resulting to an extremely small excess air ratio. It is obvious that this vapor pressure adjustment using gasoline is the dominant factor for improvement in cold startability. (10 figs, 1 tab, 10 refs)

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a 400 Mwt sodium-cooled fast reactor operating at the Hanford Engineering Development Laboratory, Richland, Washington, to conduct fuels and materials testing in support of the US Liquid Metal Fast Breeder Reactor (LMFBR) program. Startup and initial power testing included a comprehensive series of nonnuclear and nuclear tests to verify the thermal, hydraulic, and neutronic characteristics of the plant. A specially designed series of natural circulation tests were then performed to demonstrate the inherent safety features of the plant. Early in 1982, the FFTF began its first 100-day irradiation cycle. Since that time the plant has operated very well, achieving a cycle capacity factor of 94% in the most recent irradiation cycle. Seventy-five specific test assemblies and 25,000 individual fuel pins have been irradiated, some in excess of 80 MWd/Kg.

Energy Technology Data Exchange (ETDEWEB)

Tests on a sample of trench water from the Maxey Flats burial ground effectively demonstrated the new Reverse Osmosis Pilot Plant. The effluent from the 50% salt-rejection membrane was decontaminated well enough with the exception of tritium to be discharged to the environment. The performance of the 97% salt-rejection membrane was superior to that of the 50% membrane. A breakthrough and capacity experiment was conducted with Durasil 10 on a simulated Three Mile Island solution. The maximum decontamination factor was extrapolated to be 10/sup 6/, which would reduce the cesium level of TMI water to below the discard limit. Capacity (1/DF = 0.5) was reached at 1260 column volumes. Several adsorbents were tested in the engineering columns for decontamination of cesium-bearing solutions. Under the conditions of the experiment, these adsorbents were ineffective in removing cesium from the solution.

Energy Technology Data Exchange (ETDEWEB)

While it is quite obvious that photons have an essential role in photochemical and photocatalytic processes, it is not simple to analyse the radiation process. A simple approach is presented on the assumption that photons can be treated as immaterial reactants. It is then possible to evaluate the radiation process in terms of parameters such as conversion, selectivity and yield, which are common in the conventional reaction engineering, and of an additional parameter, a volume efficiency factor, which accounts for the exploitation of the reaction volume as the result of the inevitable attenuation of the radiation in the transport through the participating medium. Attention has also been focused on the validation of kinetic data when, as it is usually done, they are interpreted in terms of volume averages. Finally, guidelines have been prepared to support preliminary phases of analysis and/or design of a photocatalytic reactor. (author)

Energy Technology Data Exchange (ETDEWEB)

Radial sonic crystals (RSC) are fluidlike structures infinitely periodic along the radial direction that verify the Bloch theorem and are possible only if certain specially designed acoustic metamaterials with mass density anisotropy can be engineered (see Torrent and Sanchez-Dehesa 2009 Phys. Rev. Lett. 103 064301). A comprehensive analysis of two-dimensional (2D) RSC shells is reported here. A given shell is in fact a circular slab with a central cavity. These finite crystal structures contain Fabry-Perot-like resonances and modes strongly localized at the central cavity. Semi-analytical expressions are developed to obtain the quality factors of the different resonances, their symmetry features and their excitation properties. The results reported here are completely general and can be extended to equivalent 3D spherical shells and to their photonic counterparts.

British Library Electronic Table of Contents (United Kingdom)

Abstract 1,3 Propanediol (PDO), is now taking the transition from a traditional specialty chemical to a commodity chemical . The market for PDO is growing rapidly as the technology develops. With the advancing PDO production technology, polytrimethylene terephthalate (PTT) as a new type of polyester has been applied in carpet and textile fibers, monofilaments, films, and nonwoven fabrics, and in the engineering thermoplastics area, because PTT has unique properties compared to other polymers such as polyethylene terephthalate (PET) and polybutylene terephthalate (PBT). Responding to the environmental and sustainability factors, one or two step fermentation technology for PDO production has attracted people's attention. A novel flexible process for PDO production by using aerobic fermentati...

Energy Technology Data Exchange (ETDEWEB)

A core competency is a distinguishing integration of capabilities which enables an organization to deliver mission results. Core competencies represent the collective learning of an organization and provide the capacity to perform present and future missions. Core competencies are distinguishing characteristics which offer comparative advantage and are difficult to reproduce. They exhibit customer focus, mission relevance, and vertical integration from research through applications. They are demonstrable by metrics such as level of investment, uniqueness of facilities and expertise, and national impact. The Oak Ridge National Laboratory (ORNL) has identified four core competencies which satisfy the above criteria. Each core competency represents an annual investment of at least $100M and is characterized by an integration of Laboratory technical foundations in physical, chemical, and materials sciences; biological, environmental, and social sciences; ...

Energy Technology Data Exchange (ETDEWEB)

In accordance with the National Environmental Policy Act (NEPA) of 1969, the US Department of Energy (DOE) has prepared this document as environmental input to future decisions regarding the Waste Isolation Pilot Plant (WIPP), which would include the disposal of transuranic waste, as currently authorized. The alternatives covered in this document are the following: (1) Continue storing transuranic (TRU) waste at the Idaho National Engineering Laboratory (INEL) as it is now or with improved confinement. (2) Proceed with WIPP at the Los Medanos site in southeastern New Mexico, as currently authorized. (3) Dispose of TRU waste in the first available repository for high-level waste. The Los Medanos site would be investigated for its potential suitability as a candidate site. This is administration policy and is the alternative preferred by the DOE. (4) Delay the WIPP to allow other candidate sites to be evaluated for TRU-waste disposal. This environmental impact ...

Energy Technology Data Exchange (ETDEWEB)

This study reviews past assessments of world oil, natural gas, and oil-shale resources. It identifies the methods used in making these assessments (historical statistics, geological analogy, engineering, and probabilistic), the geographical coverage, the time horizons, and the major assumptions about such factors as discovery rates, and recovery factor. The period covered extends from the end of World War II to the end of 1980. Conclusions are presented on the current state of knowledge and understanding concerning each of these three hydrocarbon resources. Regarding world oil resources, an assumed consensus on 2000 billion barrels ultimately recoverable is, in fact, only weakly supported. Close examination of its component parts reveals widespread disagreement. World natural gas resources are even less well understood. And it is premature to venture a meaningful assessment of world oil-shale resources. Thus, our knowledge ...

Energy Technology Data Exchange (ETDEWEB)

E-35 reported the specific air flow analysis program using a CFSV model (including a human body model) to develop a high-accuracy evaluation simulator for heterogeneous thermal environment based on human thermal physiological conditions. E-36 reported development of the radiation heat transfer analysis module by using a numerical integral method to calculate shape factors. Radiation heat transfer characteristics every body part were clarified quantitatively by this module. E-37 reported the results on continuous measurement of physiological conditions and thermal environment factors every monitor under controlled indoor thermal environment, to collect measurement data necessary for improving the accuracy of a prediction program for human body temperatures. E-38 reported the study result on physiological reaction and subjective evaluation through an examinee experiment in a blood controlled region, to collect basic data for the above ...

Science.gov (United States)

OBJECTIVE To identify patients with gestational diabetes mellitus (GDM) who will need antenatal insulin treatment (AIT) by using a risk-prediction tool based on maternal clinical and biochemical characteristics at diagnosis. RESEARCH DESIGN AND METHODS Data from 3,009 women attending the Royal Prince Alfred Hospital GDM Clinic, Australia, between 1995 and 2010 were studied. A risk engine was developed from significant factors identified for AIT using a logistic regression model. RESULTS A total of 51% of GDM patients required AIT. Ethnicity, gestation at diagnosis, HbA(1c), fasting and 60-min glucose oral glucose tolerance test, BMI, and diabetes family history were significant independent determinants of AIT. Notably, only 9% of the attributable risk for AIT can be explained by the clinical factors studied. A modeled risk-scoring system was therefore a poor predictor of AIT. CONCLUSIONS Baseline maternal characteristics ...

Science.gov (United States)

Divergence betyveen aircraft engine emission regulations pro- posed by EPA and ICAO is discussed Every engine, upon entering service, requires a certificate ...

Energy Technology Data Exchange (ETDEWEB)

The primary objective of the work was to establish and verify cost and performance parameters for integrated concepts in which agricultural and other biomass derived pyrolysis oils are utilised as fuel for small scale heat and power production. Production of non-food value-added products was also considered. The cost and performance studies were carried out in Spain, Denmark, and Finland, using olive oil farming residues, straw, and rapeseed oil pressing residues and straw as fuels for pyrolysis, respectively. Use of forest residue wood fuel was also considered in the Finnish vase. A rather wide selection of biomasses was therefore studied within the project. The secondary objective was to generate experimental data to verify and support the critical features within these concepts. Experimental work, modelling, and techno-economic assessments were carried out within the project. The experimental part included: Determination of flash pyrolysis balances in a PDU-unit for four feedstock, ...

Science.gov (United States)

PMID:21807581

Energy Technology Data Exchange (ETDEWEB)

The hydroelectric industry's recognition of the importance of avoiding unexpected failure, or forced outages, led to the development of probabilistic, or risk-based, methods in order to attempt to quantify exposures. Traditionally, such analysis has been carried out by qualitative assessments, relying on experience and sound engineering judgment to determine the optimum time to maintain, repair or replace a part or system. Depending on the nature of the problem, however, and the level of experience of those included in the decision making process, it is difficult to find a balance between acting proactively and accepting some amount of risk. The development of a practical means for establishing the probability of failure of any part or system, based on the determination of the statistical distribution of engineering properties such as acting stresses, is discussed. The capacity-demand analysis methodology, coupled with probablistic, ...

Energy Technology Data Exchange (ETDEWEB)

To utilize ethanol from agricultural residue as a fuel in diesel engines, a dual-fuel engine was developed. The engine, which was equipped with a system to electrically control diesel and alcohol flow rates, met basic requirements of a tractor engine, including engine speed control and setting of the torque curve. However, engine knock due to alcohol was a significant drawback. A diesel injection pump with a timing and flow rate control system was adapted, and the effect of injection timing on combustion and performance was investigated. It was observed that the timing control was effective in reducing engine knock caused by rapid alcohol combustion. (author)

Science.gov (United States)

... management. 5.3 Decreased Emissions Changes in engine emission regulations are driving engine technology development. A ...

Energy Technology Data Exchange (ETDEWEB)

The control of piece size in ruptured rocks in coal sections is important as part of the general problem of increasing efficiency in the technology of open-pit mining operations. An attempt is made in this paper to estimate the rupture capacity of exposed rocks in coal sections based on a set of physicomechanical property indicators, using the methods of multidimensional statistical analysis. It was established that all the parameters for the physiocomechanical properties of the exposed rocks are highly correlated. The method proposed for determining criteria for explosive capacity is of interest in developing criteria for the destruction capacity (drillability, excavation capacity, etc.) in the exposed rocks of coal sections which are characterized by high variation in physical and mechanical properties.

International Nuclear Information System (INIS)

Current technical specifications of Wolsong Unit 2,3,4 was analyzed and improvement methods was suggested to develop Improved Standard Technical Specifications(ISTS) of PHWR. The selection criteria of PHWR limiting condition for operation(LCO) was established, then limiting conditions for operationl were selected. The number of current LCOs for Wolsong Units 2,3,4 is 109, and 46 LCOs(42%) were relocated by the selection criteria of PHWR LCO. 63 LCOs which met the selection criteria of PHWR LCO were recomposed to 59 LCOs.

Science.gov (United States)

... tests, one often encounters, for instance, separated flows with large ... It is suspected that the flow-quality criteria given in AGARD Report No. ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this statement of work (SOW) is to establish laboratory analytical criteria and requirements for radioactive airborne emissions measurement sample and/or analysis activities.

Science.gov (United States)

... 295 VIII Classification Criteria 305 IX List of Applicable JANAP's 307 X Sample Sheets, Eniwetok Consolidated Telephone Directory 309 ...

Science.gov (United States)

This standard establishes requirements, verification criteria, and contractor tasks for electromagnetic effects protection of airborne, ground, and support systems. These effects include electromagnetic compatibility, electromagnetic interference, lightni...

British Library Electronic Table of Contents (United Kingdom)

Multi-criteria group decision making (MCGDM) aims to support preference-based decision over the available alternatives that are characterized by multiple criteria in a group. To increase the level of overall satisfaction for the final decision across the group and deal with uncertainty in decision process, a fuzzy MCGDM process (FMP) model is established in this study. This FMP model can also aggregate both subjective and objective information under multi-level hierarchies of criteria and evaluators. Based on the FMP model, a fuzzy MCGDM decision support system (called Decider) is developed, which can handle information expressed in linguistic terms, boolean values, as well as numeric values to assess and rank a set of alternatives within a group of decision makers. Real applications indic...

Energy Technology Data Exchange (ETDEWEB)

National soil quality criteria for the protection of ecological receptors, including livestock and wildlife, are currently under development in Canada. Based on an evaluation of direct soil contact and soil and food ingestion pathways for sensitive species, soil quality criteria for lead, copper, arsenic, cadmium and mercury for three land use categories have been derived. The draft values, in mg/kg soil, for agricultural, residential/parkland, commercial/industrial land uses are: mercury, 4, 4, 30; copper, 62, 62, 100; cadmium, 10, 10, 27; lead, 70, 250, 400; arsenic, 17, 17, 26. Critical data requirements in developing soil quality criteria are also reviewed.

Energy Technology Data Exchange (ETDEWEB)

The Federal Aviation Administration (FAA) identified 17 accidents that may have resulted from fuel tank explosions on commercial aircraft from 1959 to 2001. Seven events involved JP 4 or JP 4/Jet A mixtures that are no longer used for commercial aircraft fuel. The remaining 10 events involved Jet A or Jet A1 fuels that are in current use by the commercial aircraft industry. Four fuel tank explosions occurred in center wing tanks (CWTs) where on-board appliances can potentially transfer heat to the tank. These tanks are designated as ''Heated Center Wing Tanks'' (HCWT). Since 1996, the FAA has significantly increased the rate at which it has mandated airworthiness directives (ADs) directed at elimination of ignition sources. This effort includes the adoption, in 2001, of Special Federal Aviation Regulation 88 of 14 CFR part 21 (SFAR 88 ''Fuel Tank System Fault Tolerance Evaluation Requirements''). This paper ...

International Nuclear Information System (INIS)

Various types of nuclear power plants are being constructed and operated in Korea, and in terms of regulatory control, a method of examining and evaluating the structural integrity of containment structure is being used. Generally, after the construction has been completed, all containment structure go through a Structural Integrity Test(hereinafter SIT) in which the displacement occurring in a structure under greater internal pressure than it was designed for is measured and the result is comparatively assessed with the allowed criteria. Most of the nuclear power plants in Korea are American type plants and their SIT uses the Invar-wire and Extensometer methods. These existing methods are expected to be used for the APR1400 plant currently being built unless some other reliable alternative technique is presented. This tendency can be observed in other countries, such as Japan, and there is thus insufficient effort to enhance the reliability of SIT through the ...

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) is now evaluating its facility requirements in support of its cleanup mission at Hanford. One of the early findings is that the 200-Area steam plants, constructed in 1943, will not meet future space heating and process needs. Because the 200 Area will serve as the primary area for waste treatment and long-term storage, a reliable steam supply is a critical element of Hanford operations. This Analysis and Decision Document (ADD) is a preliminary review of the steam supply options available to the DOE. The ADD contains a comprehensive evaluation of the two major acquisition options: line-term versus privatization. It addresses the life-cycle costs associated with each alternative, as well as factors such as contracting requirements and the impact of market, safety, security, and regulatory issues. Specifically, this ADD documents current and future steam requirements for the 200 Area, describes alternatives available to DOE for ...

International Nuclear Information System (INIS)

Purpose: Various published reports involving intensity-modulated radiotherapy (IMRT) plans developed using automated optimization (inverse planning) have demonstrated highly conformal plans. These reported conformal IMRT plans involve significant target dose inhomogeneity, including both overdosage and underdosage within the target volume. In this study, we demonstrate the development of optimized beamlet IMRT plans that satisfy rigorous dose homogeneity requirements for all target volumes (e.g., #+-#5%), while also sparing the parotids and other normal structures. Methods and Materials: The treatment plans of 15 patients with oropharyngeal cancer who were previously treated with forward-planned multisegmental IMRT were planned again using an automated optimization system developed in-house. The optimization system allows for variable sized beamlets computed using a three-dimensional convolution/superposition dose calculation and flexible cost functions derived from combinations of ...

Energy Technology Data Exchange (ETDEWEB)

The problem of buried steelwork in cargo hold insulation has been investigated by several using empirical methods. These efforts have resulted in correction factors that serve as a useful aid in the complex task of estimating the K-value of a ship`s cargo holds for the correct dimensioning of the refrigeration plant. Today, the advent of the digital computer has established numerical methods of analysis as a common working tool among practicing engineers. For estimating the flow in cases of buried steelwork that cannot be handled by correction factors, this is an effective approach. This study is an analytical/numerical investigation of the effect that buried steelworks have on the heat leakage across cargo hold walls. It aims at providing enlightenment on the physical significance of the parameters influencing the problem and developing practically simple methods for predicting the heat leakage across the hold walls. The ...

Wastenet

... Alexandria Engineering Journal- The Alexandria Engineering Journal (AEJ) is an international journal devoted to publishing high quality papers in the field..... Alexandria Engineering Journal - Elsevier Home Products User Resources About Us Support & Contact Elsevier Websites Advanced Product Search Browse ...Journals Alexandria Engineering Journal Alexandria Engineering Journal Production and Hosting by Elsevier B.V. on behalf of Faculty of Engineering, Alexandria University ...Indexing Editors Reviewers Log in as Reviewer Advertisers/Sponsors Societies ISSN: 1110-0168 Imprint: ALEXANDRIA UNIVERSITY Actions Submit Article Order Journal ...

Energy Technology Data Exchange (ETDEWEB)

Located approximately 350 km east of Newfoundland, on the eastern edge of the Jeanne d'Arc Basin, and approximately 50 km from both the Terra Nova and Hibernia oilfields, the White Rose oilfield is considered the main oil producing basin off the eastern coast of North America. Husky Oil is very active in the region and holds almost 32 per cent net working interest in the Significant Discovery License areas in the Jeanne d'Arc basin. The development of an economically significant oil discovery in the White Rose Significant Discovery Area is being proposed jointly by Husky Oil and Petro-Canada. It is estimated that the project would enable the recovery of an estimated 36 million cubic meters (230 million barrels) of recoverable oil in this area that covers approximately 40 square kilometers. The operators propose to use a ship-shaped floating production, storage and offloading (FPSO) facility which could store up to 135,000 cubic meters (850,000 barrels) of oil or the ...

Energy Technology Data Exchange (ETDEWEB)

This assessment is a feasibility study according to ISO 14024. It deals with the question whether an ecolabel is suitable for wood pellet heating systems and how concrete criteria for an ecolabel for wood pellet heating plants could be specified. The study begins with a comprehensive market analysis in order to identify possible plants for which an ecolabel would make sense. In the main part of the study, the environmental relevance of the chosen plants is analysed. For this analysis, plant manufacturers were interviewed and a comparison between wood pellet heating systems and heating systems which use gas, oil or wood was carried out. On the basis of this analysis, it was possible to derive a number of criteria which were discussed with company representatives and other experts in this field. As a result of this dialogue and the investigation process as a whole, the introduction of an ecolabel for wood pellet heating plants can be recommended. ...

Wastenet

... Most of the received offers were ecolabelled cleaning products and were not more expensive than conventional products. Case 3: The procurement of sustainable cleaning services 104kB Eight cooperating municipalities in the Netherlands needed a new contractor for cleaning services. They wanted to use SPP criteria as well as finding a social employment organisation. SPP criteria for cleaning services were used to set minimum requirements in ...

Energy Technology Data Exchange (ETDEWEB)

Ammonia is a common and highly toxic pollutant which, in sufficient quantities, will adversely affect aquatic organisms. This ammonia criteria document for salt water will allow establishment of regulatory standards for ammonia discharge into estuaries, near coastal zones and oceans. Possible adverse impacts in highly sensitive and abundant ecosystems such as estuaries make regulation particularly important.

Energy Technology Data Exchange (ETDEWEB)

This paper identifies the event sequences that require thermal-hydraulic analyses for the success criteria of probabilistic safety analysis (PSA). The selection of the sequences is performed based on the review of the NEI Peer Review Process Guidance and ASME PRA Standard. Success criteria are the important element of PSA quality. Success criteria decide the success or failure of the key function in the PSA event tree. It is defined as a minimum set of components/trains of system required to mitigate an accident. Thermal-hydraulic codes are generally used to derive time-related criteria in the PSA, such as operator action time used in human reliability analysis (HRA), event timing, and time to recover the component or the power. This paper suggests the use of the MARS code for the T-H analysis to obtain the success criteria and sequence timing, and operator action time. In the Kori ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a low emission duel fuel engine system. It comprises: a dual fuel engine having a combustion chamber; a fuel oil supply connected to the engine; a fuel gas supply connected to the engine; and means connected between the fuel oil supply and the engine for injecting fuel oil into the engine. The means connected between the engine and fuel oil supply limiting the injection of fuel oil to the combustion chamber to pilot ignition quantities only, wherein the limiting means includes means for limiting the injection of fuel oil such that the exhaust emission of NO{sub x} is at an emission rate of less than 1 GM/PH-HR, whereby the exhaust emission performance of the dual fuel engine is enhanced.

Energy Technology Data Exchange (ETDEWEB)

This paper gives details of the development of the Wartsila 32DF duel-fuel lean-burn engine that can burn liquid or gaseous fuels, and reports on the installation of four of the engines in Turkey. The combustion process, and the design of the gas admission, pilot fuel, cylinder control, air-fuel control, and engine control and monitoring systems are described. The advantages of the engine are discussed.

Energy Technology Data Exchange (ETDEWEB)

This patent describes a gas-diesel dual fuel engine apparatus having a diesel engine, a diesel fuel supply system including a diesel fuel injection pump, a gaseous fuel supply system including gaseous fuel regulating valve, and a governing and controlling device for governing the speed of the engine and controlling the switchover of the operation of the engine between a diesel fuel mode and a gaseous fuel mode.

Energy Technology Data Exchange (ETDEWEB)

One aspect of the research program SFB 570 'Distortion engineering' is the in situ X-Ray diffraction analysis of phases and residual stresses during complete heat treatment cycles. These investigations result in experimental evidence available for the extensive computations. The optimisation of the instrumentation will be reported. A surface decarburisation of samples made from the ball bearing steel 100Cr6 could be avoided for a temperature range from 800 to 900 C and a holding time of one hour by a combination of evacuate the furnace and using a certain nitrogen flow as protective gas. At lower temperatures small amounts of ferrite caused by an increased diffusion rate of carbon lead again to a surface decarburisation up to a depth of 2 {mu}m. It was proved that with an evacuation of the X-Ray beam path at constant power of the X-Ray source the intensity of diffraction lines could be increased by more than a factor of 4. The ...

Energy Technology Data Exchange (ETDEWEB)

Commercial development of oil shale resources will produce vast quantities of processed shale waste. The presence of potentially toxic trace elements, inorganic salts, and potentially toxic residual organic constitutents make the disposal of vast quantities of processed shale a potential environmental problem. To be environmentally acceptable, processed shale disposal must: result in a physically stable structure, prevent or minimize release of potentially toxic compounds, and provide an economically acceptable post-land use. Water is the common element underlying all factors important to the environmental stability of disposed solid waste. The leaching and transport of solubles by water in processed shale embankments may result in degradation of local surface and groundwater quality. The major purpose of this research is to physically model, study, and describe the redistribution and movement of water and percolates in lifts of disposed processed oil shale under ...

Energy Technology Data Exchange (ETDEWEB)

Total thermal resistance of ground heat exchanger (GHE) is comprised of that of the soil and inside the borehole. The thermal resistance of soil can be calculated using the linear source theory and cylindrical source theory, while that inside the borehole is more complicated due to the integrated resistance of fluid convection, and the conduction through pipe and grout. Present study evaluates heat exchange rate per depth of GHE by calculating the total thermal resistance, and compares different methods to analyze their similarities and differences for engineering applications. The effects of seven separate factors, running time, shank spacing, depth of borehole, velocity in the pipe, thermal conductivity of grout, inlet temperature and soil type, on the thermal resistance and heat exchange rate are analyzed. Experimental data from several real geothermal heat pump (GHP) applications in Shanghai are used to validate the present calculations. ...

Energy Technology Data Exchange (ETDEWEB)

Factors important in choosing between process concepts were mechanical complexity and amenability to scale-up studies. The culmination of this work was a process concept known as Staged Turbulent Bed Retorting Process (STB), which has now been tested in pilot plants. Operating conditions are described. The environment in the retort section can be described as a staged, moving bed of particles, in which a portion of the particles are fluidized at gas velocities well below minimum fluidization velocity of many of the particles. Research and engineering evaluations have established that the STB provides prospects for the responsible development of oil shale resources on a commercial scale. A 320 ton/d semiworks unit, the next technological step, will be commissioned shortly. This unit will be large enough to provide scale-up data for design of modules and to demonstrate the entire process, generating data needed to optimize, design, and construct ...

Energy Technology Data Exchange (ETDEWEB)

Reviews types of hydraulic power shovels used in coal surface mines in the USA, FRG, Japan and other countries. Excavators of the first, second and third generation are compared. Hydraulic schemes of the excavators are compared. The following excavators are reviewed: the RH-75, RH-75C, 1000 SK, H-801, RC-1500, H-185, EX-1800, R-994, RH-120C, H-241, Marion 3560, H-285, EX-3500, H-485, RH-300. The following parameters are compared: mass, price, digging range, digging power, productivity, motors, travelling speed, availability coefficient, pressure in the hydraulic systems, control systems. The following elements are discussed: schemes of hydraulic drives, main motors and engines, pump stations, hydraulic equipment, hydraulic accumulators, systems for cleaning and cooling hydraulic fluids, control systems, working fluids. Reliability of hydraulic power shovels and factors that influence reliability are analyzed. 54 refs.

Energy Technology Data Exchange (ETDEWEB)

Formation of particles from heavy duty diesel and CNG vehicles was studied in laboratory conditions. PM, nano and soot mode particle emissions formed from buses of Euro 2-5 -emission levels were studied in relation to age and type approval characteristics of the vehicle. Characteristic particle emission factors from city driving were obtained by driving the buses on VTT's heavy duty chassis dynamometer applying the transient Braunschweig city cycle. The vehicles were a representative set of Euro 2 to 3 emission categories, supplemented with Euro 4-5 (EEV) -targeted CRT, CNG and DPF cars. Particle number emissions from Euro 4 to 5 buses were 1/100-1/1000 and mass emissions 1/10-1/100 of those of the current fleet. Particle emission from natural gas buses and after an advanced CRT trap contained almost entirely liquid < 60 nm nano particles, which will make filter mass based PM control very challenging in the near future. One result was that ...

Energy Technology Data Exchange (ETDEWEB)

Exhaust fine and ultra fine particle numbers, particle sizes, mass, shape, structure and density were studied from Euro II - EEV emission level heavy-duty vehicles. For total particle emission factors city buses were run on dynamic conditions simulating city bus driving. The new heavy-duty chassis dynamometer of VTT was used. Vehicles were a comprehensive sample of current city bus fleet, the type approved emission level of which was Euro II - Euro III. Also cleaner engines of Euro IV to EEV targeted emission level were included: CRT, CNG, DPF. Particle emissions of these buses were extremely low; numbers 1/100 - 1/1000 and masses 1/10 - 1/100 of those of the predominating techniques. Morphological properties of fine particle populations that represent majority of particle size distribution (Da < 500 nm) are being analyzed by image processing (Matlab) from electron microscopical images (SEM, ESEM and TEM) as a function of particle size. ...

Science.gov (United States)

The reconstruction of segmental defect in long bone is a clinical challenge. Multiple surgeries are typically required to restore the structure and function of the affected defect site. In order to overcome this defect a biodegradable bone tissue engineering scaffold is used. This scaffold acts as a carrier of proteins and growth factors, while also supporting the load that the bone would normally sustain, until the natural bone can regenerate in its place. Work was done to optimize an existing solid free-form scaffold design. The goal of the optimization was to increase the porosity of the scaffold while maintaining the strength of a previously-tested prototype design. With this in mind, eight new designs were created. These designs were drawn using CAD software and then through the use of finite element analysis the theoretical ultimate compressive strength of each design was obtained. Each scaffold design was constructed by casting a ...

Science.gov (United States)

This is the quarterly progress review report for Wolsung NPP 2, 3, 4 NSSS design and engineering which evaluates the performance of project and describes the project highlight, manpower loading status, design and engineering and project related meeting by...

International Nuclear Information System (INIS)

This guide explained the requirements for Off-Road Compression Ignition Engine Emission Regulations established under the Canadian Environmental Protection Act. The regulations are enforced by Environment Canada, which authorizes and monitors the use of the national emissions mark. The regulations prescribe standards for off-road engines that operate as reciprocating, internal combustion engines, other than those that operate under characteristics similar to the Otto combustion cycle and that use a spark plug or other sparking device. The regulations apply to engines that are typically diesel-fuelled and found in construction, mining, farming and forestry machines such as tractors, excavators and log skidders. Four different types of persons are potentially affected by the regulations: Canadian engine manufacturers; distributors of Canadian engines or machines ...

Science.gov (United States)

... Programmatic Terms and Conditions for the Materials Research Science and Engineering Centers (MRSEC ... NSF Grants Officer. 2. Program Description: Materials Research Science and Engineering Centers ...

Wastenet

...Electronic equipment,Embedded computer systems,Technology & Engineering,Automotive - General,COMPUTERS / Computer Engineering,TECHNOLOGY & ENGINEERING / Electronics ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Hydrogen piston engines can be simultaneously optimized for improved thermal efficiency and for extremely low emissions. Using these engines in constant-speed, constant-load systems such as series hybrid-electric automobiles or home cogeneration systems can result in significantly improved energy efficiency. For the same electrical energy produced, the emissions from such engines can be comparable to those from natural gas-fired steam power plants. These hydrogen-fueled high-efficiency, low-emission (HELE) engines are a mechanical equivalent of hydrogen fuel cells. HELE engines could facilitate the transition to a hydrogen fuel cell economy using near-term technology.

Energy Technology Data Exchange (ETDEWEB)

This work reviews the differences in fuel economy between two direct injection diesel engine versions through the use of a First Law energy balance and a Second Law availability balance. Both experimental data and simulated results are used in the analysis. The use of an engine simulation allowed the important processes in each engine to be analyzed and a Second Law effectiveness calculated. The availability balances and effectiveness values are used to determine the effect of major engine components on the fuel economy. A comparison is also made with an ideal engine with selected perfect or reversible processes.

Science.gov (United States)

Engine flow simulation was provided by four separately mounted air ejectors connected to a high-pressure air supply. The engine nacelle center lines were ...

Science.gov (United States)

of the Intelligent Control System (ICS) for reusable rocket engines. .... the incoming measurements with corresponding estimates, a sensor failure can be ...

Science.gov (United States)

NSF-NIST Interaction in Chemistry, Materials Research, Molecular Biosciences, Bioengineering, and ... Laboratory (CSTL). Materials research is centralized in the Materials Science and Engineering ...

Science.gov (United States)

Graphitized thermal carbon black has also been reported by Kalaschinikova et al. (11) to have excellent adsorption properties for CI-C6 alkanes, ...

Science.gov (United States)

... CI Appendix D: Conference Attendees ..... D1 Appendix E: Structural Steel Connection Design on Federal Projects ..... El iv ...

Science.gov (United States)

NASA 1996 STTR Phase I. Proposal Number: 960022. Project Title: ADVANCED INTERNAL COMBUSTION ENGINE USING JET FUELS FOR LIGHT AIRCRAFT ...

British Library Electronic Table of Contents (United Kingdom)

This paper presents an investigation into the feasibility and potential advantages of a small scale Miller cycle natural gas engine for applications such as domestic combined heat and power systems. The Miller cycle engine is compared to a standard Otto cycle engine using cycle analyses and multidimensional simulation, and basic engine design implications are discussed. It is found that the Miller cycle engine has a potential for improved fuel efficiency, but at the cost of a reduced power to weight ratio. A fuel efficiency advantage of Formula Not Shown compared to a standard Otto cycle engine appears possible, however it is stated that further investigations, in particular into the topic of engine friction, are required in order to validate the findings.

ScienceCinema

@ work highlights Idaho National Laboratory employees and the jobs they perform.This segment features Robotic Software Engineer Miles Walton.

British Library Electronic Table of Contents (United Kingdom)

An extension of TOPSIS, a multi-criteria interval-valued intuitionistic fuzzy decision making technique, to a group decision environment is investigated, where inter-dependent or interactive characteristics among criteria and preference of decision makers are taken into account. To get a broad view of the techniques used, first, some operational laws on interval-valued intuitionistic fuzzy values are introduced. Based on these operational laws, a generalized interval-valued intuitionistic fuzzy geometric aggregation operator is proposed which is used to aggregate decision makers? opinions in group decision making process. In addition, some of its properties are discussed. Then Choquet integral-based Hamming distance between interval-valued intuitionistic fuzzy values is defined. Combining ...

Energy Technology Data Exchange (ETDEWEB)

For the construction of underground facilities comprising access tunnels, connecting tunnels, main tunnels and disposal tunnels, a large number of tunnels will be excavated in deep rock formations. These excavations will extend hundreds kilometers in total length. Therefore, special attention must be paid, to transporting large volume of debris, ventilation, emergency escape routes in case of accident, and other factors. In addition, special attention must also paid to potential accidents which might in underground excavations, including unstable facing phenomena (such as collapse and swelling of facing at weak layer sections), spring water flow resulting collapse of rock, gas eruption, and rock burst. While considering these factors to be emphasized during the construction of geological disposal facilities, the investigation reviewed the existing working methods on individual construction technologies of access tunnels, main tunnels, ...

Energy Technology Data Exchange (ETDEWEB)

Mesenchymal stem cells (MSCs) are a potential source of smooth muscle cells (SMCs) for constructing tissue-engineered vascular grafts. However, the details of how specific combinations of vascular microenvironmental factors regulate MSCs are not well understood. Previous studies have suggested that both mechanical stimulation with uniaxial cyclic strain and chemical stimulation with transforming growth factor {beta}1 (TGF-{beta}1) can induce smooth muscle markers in MSCs. In this study, we investigated the combined effects of uniaxial cyclic strain and TGF-{beta}1 stimulation on MSCs. By using a proteomic analysis, we found differential regulation of several proteins and genes, such as the up-regulation of TGF-{beta}1-induced protein ig-h3 (BGH3) protein levels by TGF-{beta}1 and up-regulation of calponin 3 protein level by cyclic strain. At the gene expression level, BGH3 was induced by TGF-{beta}1, but calponin 3 was not ...

Energy Technology Data Exchange (ETDEWEB)

Cylindrical shells with regular perforation are widely used in power generating equipment and in particular in collectors 1 of the circuit of steam generators of power generating installations with water-water reactors (WWPR) The state of stress of collectors is determined by a broad spectrum of technological and operational loads, it is therefore difficult to analyze it theoretically. The aim of the present work is the experimental investigation of stresses in the cylindrical shells of collectors subjected to internal pressure, the generalization and systematization of empirical data in the form of engineering formulas and nomographs. The investigations were carried out with photoelastic three-dimensional models with the use of {open_quotes}freezing{close_quotes}. The basic characteristics of the state of stress of perforated shells (in particular those used in calculations of the strength and life of collectors) are the values of the stress intensity ...

Energy Technology Data Exchange (ETDEWEB)

Some motor operated valves now have higher torque switch settings due to regulatory requirements to ensure valve operability with appropriate margins at design basis conditions. Verifying operability with these settings imposes higher stem loads during periodic inservice testing. These higher test loads increase stresses in the various valve internal parts which may in turn increase the fatigue usage factors. This increased fatigue is judged to be a concern primarily in the valve disks, seats, yokes, stems, and stem nuts. Although the motor operators may also have significantly increased loading, they are being evaluated by the manufacturers and are beyond the scope of this study. Two gate valves representative of both relatively weak and strong valves commonly used in commercial nuclear applications were selected for fatigue analyses. Detailed dimensional and test data were available for both valves from previous studies at the Idaho National ...

Science.gov (United States)

Testing was performed to determine the feasibility and processing characteristics of evaporation of actual Defense Waste Processing Facility (DWPF) recycle material. Samples of the Off Gas Condensate Tank (OGCT) and Slurry Mix Evaporator Condensate Tank (SMECT) were transferred from DWPF to the Savannah River National Lab (SRNL) Shielded Cells and blended with De-Ionized (DI) water and a small amount of Slurry Mix Evaporator (SME) product. A total of 3000 mL of this feed was concentrated to approximately 90 mL during a semi-batch evaporation test of approximately 17 hours. One interruption occurred during the run when the feed tube developed a split and was replaced. Samples of the resulting condensate and concentrate were collected and analyzed. The resulting analysis of the condensate was compared to the Waste Acceptance Criteria (WAC) limits for the F/H Effluent Treatment Plant (ETP). Results from the test were compared to previous testing using simulants and ...

UK PubMed Central (United Kingdom)

The difficulties created by the lack of generally accepted views on classification, diagnostic criteria and natural history of the cutaneous lymphomata are discussed. Only the lymphomata which remain...Full Text Available

Science.gov (United States)

These sky images are scanned for point sources above a specified ... The threshold criteria are: a) Gold: >4 sigma in both the Soft AND Hard bands. b) Silver: ... Filtering: Currently, there is no plan for filtering within the GCN based ...

Science.gov (United States)

Jul 5, 2007 ... Search Criteria: Search Field: All > Results : All > Search Term: (Manganese 63) [x]. Sort results by: NASA Center | Date Added to NTRS ...

Energy Technology Data Exchange (ETDEWEB)

A mechanistic understanding of fracture in human bone is critical to predicting fracture risk associated with age and disease. Despite extensive work, a mechanistic framework for describing how the underlying microstructure affects the failure mode in bone is lacking.

Science.gov (United States)

The GBM location uncertainties range from 5-15deg (radius, 1 sigma, stat+sys). ... The site's dis/enabling on Notice types and their other filter criteria .... Fermi Pointing Direction Notice gives the current pointing direction of the ...

Science.gov (United States)

Contents: Introduction; Design Criteria for a Green Building; Comparison of Energy Efficiency Measures; Whole House Energy Efficiency; Built Examples of Energy Efficient Houses; and Product Energy of Building Elements.

Science.gov (United States)

Recommended ERLs for whole body, thyroid, lung and other single organs are presented in tabular form, and related to the relevant counter measures such as evacuation, sheltering, distribution of stable iodine tablets, etc. Application of ERLs to local env...

UK PubMed Central (United Kingdom)

Objective:To estimate the prevalence of insulin resistant syndrome (IRS) among newly diagnosed patients with type 2 diabetes and to test their validity against two indices...Full Text Available

UK PubMed Central (United Kingdom)

Since the establishment of the National Toxicology Program (NTP), there have been gradual changes in strategies to evaluate the overall toxicity of chemicals as well as their carcinogenic potential....Full Text Available

Science.gov (United States)

...Track haulage roads. (a) The speed at which haulage equipment is operated should be determined by the condition...elements of the track and the type and condition of the haulage equipment. (b) Track haulage roads should...

Energy Technology Data Exchange (ETDEWEB)

Petroleum resources are finite and, therefore, search for their alternative non-petroleum fuels for internal combustion engines is continuing all over the world. Moreover gases emitted by petroleum fuel driven vehicles have an adverse effect on the environment and human health. There is universal acceptance of the need to reduce such emissions. Towards this, scientists have proposed various solutions for diesel engines, one of which is the use of gaseous fuels as a supplement for liquid diesel fuel. These engines, which use conventional diesel fuel and gaseous fuel, are referred to as 'dual-fuel engines'. Natural gas and bio-derived gas appear more attractive alternative fuels for dual-fuel engines in view of their friendly environmental nature. In the gas-fumigated dual-fuel engine, the primary fuel is mixed outside the cylinder before it is ...

KoreaScience (Korea)

Full Text Available

CERN Document Server

By using a laser and maser in tandem, it is possible to obtain laser action in the hot exhaust gases involved in heat engine operation. Such a "quantum afterburner" involves the internal quantum states of working gas atoms or molecules as well as the techniques of cavity quantum electrodynamics and is therefore in the domain of quantum thermodynamics. As an example, it is shown that Otto cycle engine performance can be improved beyond that of the "ideal" Otto heat engine.

International Science & Technology Center (ISTC)

Plasma Technologies of Solid Fuels Processing for Power Engineering and Metallurgy

International Nuclear Information System (INIS)

... 1343-3563 v. 57(1) SPECIFIC NUCLEAR REACTORS AND ASSOCIATED

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Science & Technology Center (ISTC)

Development of the Method of Electrodepositing Nanostructured Composite Coatings with Improved Engineering Properties

Energy Technology Data Exchange (ETDEWEB)

The modification of a turbocharged diesel engine to a dual-fuel engine using methane as the supplementary fuel has been carried out. The effect of the gaseous fuel in a turbo-charged diesel engine has been investigated by means of a heat release study and a computer program already developed at Leicester Polytechnic. It is used in order to examine the rate of heat released under any operational condition.

Wastenet

condenser, gas refiner, oil (gas) storage tank and dual fuel engine

International Nuclear Information System (INIS)

... Engineering, Kitakyushu, Fukuoka (Japan) Hattanda, Takumi NTT Advanced

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper presents a multicriteria analysis of ventilation during summertime in Europe. Multicriteria analysis theories are used to determine the most suitable ventilation strategy on a university building, that is to say to ensure the best possible indoor air quality, thermal comfort of the occupants and the lower energy consumption in case of accelerated diurnal or nocturnal ventilation and/or air conditioning. After defining the possible actions, the criteria of quality regarding thermal comfort, indoor air quality and energy consumption are defined. The possible actions are then assessed relative to each of these three criteria and ranked from the best to the worst ones using two different multicriteria analysis methods. (author)

Energy Technology Data Exchange (ETDEWEB)

Test bed trials of the Sulzer RTA84 dual-fuel engine were successfully completed at the IHI Aioi engine works (Japan) in April 1986. This newly-developed engine-type, output range 15 to 40 MW, can be operated with both diesel or heavy oil and methane gas at comparable thermal efficiency and unchanged output. The RTA dual-fuel engine was developed in close collaboration between Sulzer Brothers Limited and its Japanese licenses. Intended for the propulsion of LNG carriers, where the boil-off gas from the ship's cargo is exploited for the generation of electricity in stationary plants, the RTA dual-fuel engines is an economic and reliable alternative to the steam or gas turbine. The performance of the engine is discussed.

Energy Technology Data Exchange (ETDEWEB)

Recently, utilization of natural gas, which is considered to be one of most important alternative fuels for petroleum, has been marked. As thermal efficiency of dual-fuel engine is higher than those of other prime movers with gaseous fuel, i.e., spark-ignited gas engine or gas turbine, it is possible to construct fuel-economical gas power plants with dual-fuel engines. However, its horsepower has been limited to the rather lower range. In 1984, NKK succeeded in developing large-sized dual-fuel engines based on the Pielstick PC4 diesel engine. The horsepower is 1200 HP/cyl, i.e. 21,600 HP for 18-cyclinder engine.

Wastenet

...Cummins Turbo Technologies launches new family of turbochargers for smaller diesel engines at IAA Hannover, public service, publicservice.co.uk Cummins Turbo Technologies ...launches new family of turbochargers for smaller diesel engines at IAA Hannover Cummins Turbo Technologies launches new family of turbochargers for smaller diesel engines at IAA ...Facebook Delicious Cummins Turbo Technologies launches new family of turbochargers for smaller diesel engines at IAA Hannover Cummins Turbo Technologies, a global engineering leader ...turbocharger technology, launched a new range of diesel turbochargers specifically designed for diesel engines from 2 -5 litre capacity today at IAA Hannover. Cummins ...

UK PubMed Central (United Kingdom)

A summary of the effects presented here is given in the table. The designation "factor present" implies that there is knowledge (from human or animal studies, or both) of a specific factor(s) present...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The fuel-injection system of the Niigata 6L 16X-AG dual-fuel engine is structured to steadily supply injected fuel during diesel-engine operation, and to distribute oil at a low rate to all the cylinders during gas-engine operation. The dual-fuel engine is started by the diesel engine operation and is changed over to gas-engine operation when the load increases. This change over is done automatically with a link mechanism. Regarding the gas-supply system, the changing pressure of supply gas is controlled by a pressure control valve which is stable and most adequate for the engine. The dual-fuel engine has the following features: (1) a high compression ratio is adopted, which reduces fuel consumption and thermal efficiently; (2) if the supply of gas decreases or stops, while continuing loaded operations, it can ...

Science.gov (United States)

Divergence between aircraft engine emission regulations proposed by EPA and ICAO is discussed. Every engine, upon entering service, requires a certificate as to its compliance with emission standards. It is shown that despite the large variability in the measurements, it is possible to devise a certification procedure requiring the testing of one engine only. Statistical modeling of such a test at the 5% significance level is described. Values of the parameter standard deviation/mean recommended as certification standards for various pollutants are given. Features of a rational certification scheme to be formulated are outlined.

Wastenet

... John Cannaday and Ken Weddle present the framework for a Product Design Engineering project (http://engineering.dartmouth.edu/~teps/images/ProductDesign.pdf) for high school students which may have relevance at a more advanced level. David Price has created a Mechanical Engineering Design (http://www.soton.ac.uk/~cds/) site containing engineering design notes. The Virtual Reality Engineering Library Home Page at the University of Bristol (http://www.dig.bris.ac.uk/virtual_lib/) is a library ...

International Nuclear Information System (INIS)

This paper discusses key methods for sustaining quality engineering data, the fundamental principles that these methods are based on, and the methods for supporting the performance of nuclear power plants by the provision of quality engineering data at all times. The concept of an 'engineering data foundation', and a Configuration Management data model are developed. The concepts and methods for managing the integrity of engineering data across many different databases and document systems are developed, including the key concepts of data-positions and data-values, Master Data and Copy Data, and the concept of a 'partnership between people and technology'. (author). 7 refs., 1 tab., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

The paper considers the cyclic variations in performance parameters of a dual fuel engine fuelled with methane. It is shown that such an engine does display cyclic variations that are greater than the corresponding diesel operation, yet smaller than comparable spark ignition operation. The extent of cyclic variation in peak cylinder pressure and ignition delay increases, for any power output, as the pilot diesel quantity is reduced and the extent of gas substitution is increased. The use of extremely small pilots in the unmodified engine can lead to erratic engine performance. Greater cyclic variations are associated with low lead rather than high load operation.

International Nuclear Information System (INIS)

The Belgian radioactive waste management agency NIRAS/ONDRAF has undertaken a comparative assessment study on long-term waste management options for the high-level and/or long-lived radioactive waste that should be managed as a result of the use of nuclear energy in Belgium. This study is one of the supportive documents to a Strategic Environmental Assessment (SEA) process initiated end of 2008 and geared towards a decision in principle by the Belgian Government in 2010 on the long-term management of such radioactive waste. NIRAS/ONDRAF, together with Belgian and international research organisations, has developed a reference option for such high-level and long-lived radioactive waste, called Category B and C Waste, consisting of the disposal of such waste in a clay formation [SAFIR-2]. More than 30 years of R and D have been undertaken resulting, among others, in the underground research facility HADES, though the decision in principle by government, supported by society via ...

UK PubMed Central (United Kingdom)

Dysregulation of the alternative pathway of complement activation, caused by mutations or polymorphisms in the genes encoding factor H, membrane co-factor protein, factor I or factor B, is associated...Full Text Available

UK PubMed Central (United Kingdom)

Human Factor VIII/von Willebrand factor, purified by calcium citrate-cellulose chromatography and 4% agarose gel filtration was subjected to sodium dodecyl sulfate gel electrophoresis on gels containing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Direct injection diesel engines power most of the heavy-duty vehicles. Due to their superior fuel economy, high power density and low carbon dioxide emissions, turbocharged, small bore, high speed, direct injection diesel engines are being considered to power light duty vehicles. Such vehicles have to meet stringent emission standards. However, it is difficult to meet these standards by modifying the in-cylinder thermodynamic and combustion processes to reduce engine-out emissions. After-treatment devices will be needed to achieve even lower emission targets required in the production engines to account for the anticipated deterioration after long periods of operation in the field. To reduce the size, mass and cost of the after-treatment devices, there is a need to reduce engine-out emissions and optimize both the engine and the aftertreatment devices as one ...

International Nuclear Information System (INIS)

Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and ...

Energy Technology Data Exchange (ETDEWEB)

ABB Industrietechnik AG recently has introduced an augmented version of its Cyldeyt cylinder pressure monitoring system aimed at spark-ignited and diesel/gas, dual-fuel engines. In addition to recording and evaluating cylinder pressure as a means of assessing engine condition, the new Cyldet version now evaluates the cylinder pressure signals to provide protection against pre-ignition related damage. When pre-ignition reaches critical levels, the Cyldet computer relays alarm signals in two stages to the overriding engine control system of the power plant. On receiving the first-stage alarm signal, the engine control system is programmed to adjust one or more engine settings to eliminate preignition - a typical adjustment is to lower charge-air temperature, for example. If such measures fail to eliminate pre-ignition, in the case of a dual-fuel engine, a second ...

Energy Technology Data Exchange (ETDEWEB)

10 papers are presented with the following titles: coal fueled diesel engine development update at GE transportation systems; features and performance data of Cooper-Bassemer coal-fueled six-cylinder LSB engine; preliminary test data and systems analysis of a high pressure coal fuel processor/engine system concept; study for coal-water-slurry fuel combustion in a high speed diesel engine; design and operation of a medium speed 12-cylinder coal-fueled diesel engine; progress on the investigation of coal water slurry fuel combustion in a medium speed diesel engine: part 5 - combustion studies; injection characteristics of coal-water slurries in medium speed diesel equipment; coal-water slurry spray characteristics of a positive displacement fuel injection system; novel injector techniques for coal-fueled diesel engines; and investigation of ...