British Library Electronic Table of Contents (United Kingdom)

A new series of anatase TiO2 hollow structures were prepared by a facile hydrothermal process. When the hydrothermal time was increased from 20min to 72h, the resulting TiO2 solid spheres gradually transformed into TiO2 hollow spheres with higher surface crystallinity and exposed {001} facets. The as-prepared TiO2-72h sample exhibited the highest activity comparing to other TiO2-based samples and commercial product Degussa P-25 towards the selective photocatalytic oxidation of toluene to benzaldehyde. Such great photocatalytic performance was mainly attributed to enhanced UV-adsorption and better charge separation efficiency due to higher surface crystallinity of TiO2-72h.

Energy Technology Data Exchange (ETDEWEB)

Nano-wire arrays of Niobium were produced by small angle sputtering on facetted sapphire, using the self shadowing effect of the facets. A wire width of about 80 nm was adjusted, the mean (maximum) wire height was about 20 nm (30 nm), the length can be in the cm range. Meander-film morphologies of 20 nm mean (26 nm maximum) thickness were produced by conventional sputtering onto smooth sapphire substrates at elevated temperatures. The morphology of the wires was investigated with atomic force microscopy (AFM), using contact mode. Meander-films were studied by scanning tunnelling microscopy (STM). Hydrogen loading was performed by instantaneously increasing the hydrogen gas pressure above the solubility limit. Thus, an elongated hydride could be monitored in an about 30 nm thick wire. STM studies on meander-films show the presence of cylindrical hydrides. Local out-of-plane and in-plane expansion can be explained by the formation of hydrides, ...

International Nuclear Information System (INIS)

In the present paper it is assumed that above a limiting value of fission fluency (burn-up) a more intensive process of irradiation introduced chemical interaction occurs. A significant part of fission gas product is thus expected to be chemically bounded in the matrix of UO_2 fuel. The fission gas atoms substituting, for example, uranium atoms in the crystallographic lattice can form weak facets. At a certain saturation condition, division of the grains can occur at the weak facets and the increase in fission-gas products release may be expected. The fact that the process of grain division for high burn-ups (70-80 MWd/kgU) forms an extremely fine structure up to the temperature as high as 1100 "oC and simultaneously the observed decreases in fission gas concentration in the fuel supports this concept. The analysis of fission gas concentration change due to the formation of nanostructures in UO_2 fuel at high burn-ups in terms of total ...

Energy Technology Data Exchange (ETDEWEB)

The multi-faceted research effort of the EBIT (Electron Beam Ion Trap) program in N-Division of the Physics and Space Technology Department at Lawrence Livermore National Laboratory (LLNL) continues to contribute significant results to the physical sciences from studies with low energy very highly charged heavy ions. The EBIT program attracts a number of collaborators from the US and abroad for the different projects. The collaborations are partly carried out through participating graduate students demonstrating the excellent educational capabilities at the LLNL EBIT facilities. Moreover, participants from Historically Black Colleges and Universities are engaged in the EBIT project. This report describes EBIT work for 1995 in atomic structure measurements and radiative transition probabilities, spectral diagnostics for laboratory and astrophysical plasmas, ion/surface interaction studies, electron-ion interactions studies, retrap and ion ...

UK PubMed Central (United Kingdom)

AIM: To evaluate the effects of percutaneous ozone injection via the posterior-lateral route and inner margin of the facet joint in the treatment of large lumbar disc herniation.METHODS:...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Strong support for the existence of catalytically-active, sub-surface oxygen is proposed. The existence of two types of sub-surface oxygen was determined by thermal-desorption spectroscopy (TDS). The first is termed O{sub {beta}} and is characterized by a board thermal-desorption peak centered at approximately 773 K. The second is referred to as O{sub {gamma}} and is characterized by an unsaturated thermal desorption signal beginning at approximately 873 K. O{sub {gamma}} is assigned to oxygen which is incorporated in the uppermost layers of low-indexed terminating crystal structures such as (111) formed as a result of thermal reordering. O{sub {beta}} diffusion occurs most likely via interstitial jumping and O{sub {gamma}} via interstitialcy diffusion. Both CH{sub 4} conversion and C{sub 2} selectivity improve with time on stream. This improvement in catalytic performance correlates well with surface ...

Energy Technology Data Exchange (ETDEWEB)

Recent research has shown that biologically inspired approaches to materials synthesis and self-assembly, hold promise of unprecedented atomic level control of structure and interfaces. In particular, the use of organic molecules to control the production of inorganic technological materials has the potential for controlling grain structure to enhance material strength; controlling facet expression for enhanced catalytic activity; and controlling the shape of nanostructured materials to optimize optical, electrical and magnetic properties. In this work, we use organic molecules to modify silver crystal shapes towards understanding the metal-organic interactions that lead to nanoparticle shape control. Using in situ electrochemical AFM (EC-AFM) as an in situ probe, we study the influence of a cationic surfactant cetyltrimethylamminobromide (CTAB) on Ag growth during electrochemical deposition on Ag(100). The results show that the organic surfactant promotes the ...

Science.gov (United States)

III--V based devices such as field effect transistors, heterojunction bipolar transistors, and lasers often have surface leakage and thermal degradation problems due to surface states which pin the Fermi level to the midgap. Sulfur based passivation processes are known to improve device performance by altering surface-state densities. We have developed a voltage-controlled anodic sulfur passivation scheme using Na[sub 2]S dissolved in ethylene glycol. Our process has repeatedly produced a [similar to]25% improvement in peak output power near the catastrophic damage limit in visible ([lambda]=670 nm) AlGaInP edge-emitting lasers. The threshold current density before and after passivation, and the [ital I]--[ital V] characteristics before and after catastrophic failure, were essentially unchanged indicating that passivation raises the threshold for facet damage.

International Nuclear Information System (INIS)

Surface-sensitive UV photoelectron yield spectroscopy was employed to study electron acceptor levels at surfaces of chalcopyrite structure Cu-In-Se thin films. Surface Fermi level pinning was observed for Cu-rich films. Shallow acceptor levels ascribable to defects Cu_I_n and V_C_u were observed for near-stoichiometric and In-rich films respectively. (orig.).

UK PubMed Central (United Kingdom)

The interior of 237 nm spherical vinylsilsesquioxane nanoparticles has been covalently modified and their surface functionalized under mild conditions to yield a novel type of hybrid silsesquioxane...Full Text Available

Science.gov (United States)

... JTIDS) LPC-10 voice channel has been an important facet of a larger ongoing in-house research task on Digital Audio Technology for Aircraft ...

Energy Technology Data Exchange (ETDEWEB)

A massively-parallel ab initio computer code, which uses Gaussian bases, pseudopotentials, and the local density approximation, permits the study of transition-metal systems with literally hundreds of atoms. We present total energies and relaxed geometries for Ru, Pd, and Ag clusters with N = 55, 135, and 140 atoms; we also used the DMOL code to study 13-atom Pd and Cu clusters, with and without hydrogen. The N = 55 and 135 clusters were chosen because of simultaneous cubo-octahedral (fcc) and icosahedral (icos) sub-shell closings, and we find icos geometries are preferred. Remarkably large compressions of the central atoms are observed for the icos structures (up to 6% compared with bulk interatomic spacings), while small core compressions ({approx} 1 %) are found for the fcc geometry. In contrast, large surface compressive relaxations are found for the fcc clusters ({approx} 2-3% in average nearest neighbor spacing), while the icos surface ...

International Nuclear Information System (INIS)

We report the oxygen, hydrogen, and deuterium effects on nitrogen implantation of stainless steel. Oxygen is absorbed on the surface creating a potential barrier and diminishing the nitrogen retention. Deuterium removes more oxygen from the surface than hydrogen, augmenting the nitrogen chemical potential and yielding faster nitrogen diffusion into the bulk material.

International Nuclear Information System (INIS)

Isotopically selective IR multiphoton dissociation of molecules (SF_6, CF_3I) in a pulsed gas-dynamic flow interacting with a solid surface was studied for the first time. A noticeable (severalfold) increase in the yield of products (compared to excitation of molecules in an unperturbed flow) without a substantial decrease in the selectivity of the process was observed. Possible reasons for the effect are discussed. (laser applications and other topics in quantum electronics)

International Nuclear Information System (INIS)

The optical emission of excited H reflected from clean Cu(110) after impingement of H"+ and H_2"+ in the energy range of 250 eV to 20 keV per nucleon at 70"0 angle of incidence to the surface normal was measured. For incident 10 keV H_2"+, the highest excited hydrogen state detected was the n=10 level. The Hsub(#alpha#) yield was found to be fluence and energy dependent. This effect is attributed either to fast sputtered hydrogen, surface roughness or to an increase with hydrogen concentration in electron states of p-like symmetry near the Fermi level of copper. The Hsub(#alpha#) yield per reflected nucleon shows approximately an exponential dependence on both projectile energy per nucleon and scattered particle reciprocal velocity perpendicular to the surface. (orig.).

UK PubMed Central (United Kingdom)

The ternary complex factor (TCF) Elk-1 is a transcription factor that regulates immediate early gene (IEG) expression via the serum response element (SRE) DNA consensus site. Elk-1 is associated with...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Decreasing the aperture of a solar central receiver operating at high temperatures contributes significantly to the increase of the efficiency of energy absorption. However, decreasing the aperture also decreases the collection efficiency. A simple solution is using a 3D-CPC as secondary element for augmenting the energy collection, while the aperture can remain relatively small. Nevertheless, the receiver aperture as well as the secondary concentrator are usually rather large. For practical considerations an approximate solution may be chosen at times, designing the concentrator by a series of truncated cones. However, in particular cases, the solution of truncated cones remains expensive and unpractical and therefore the authors designed a CPC approximated by a series of trapezoidal planar facets. Under technical restrictions, there is an optimum for choosing the partition of the pure-CPC in truncated pyramids and the paper presents the method for a good ...

International Nuclear Information System (INIS)

The swelling behavior which results from simulated fusion environment irradiation of Fe-10% Cr has been characterized with transmission electron microscopy. Specimens were bombarded at 850 K with: a ''triple-beam'' of He"+, D_2"+, and 4 MeV Fe"+"+ ions to 0.3, 1, 3, 10, 30, and 100 dpa (displacement per atom); a ''dual-beam'' of He"+ and 4 MeV Fe"+"+ ions to 30 and 100 dpa; and a ''single-beam'' of 4 MeV Fe"+"+ ions to 30 dpa. The helium and hydrogen injection rates were approx. =10 appm He/dpa and approx. =40 appm D/dpa. Cavities were observed for damage levels of 3 dpa and greater. The swelling was <0.1% for damage levels <30 dpa, but at 100 dpa, there was an increase in the swelling to 2.5% for the ''triple-beam'' irradiation and 1.2% for the ''dual-beam'' irradiation. The swelling rates between 30 and 100 dpa correlate well with calculated values assuming a steady-state swelling-rate regime has been reached. Calculations show the rapid cavity growth associated with this ...

Science.gov (United States)

An improved acousto-optic laser Q-switch uses a chirped fm pulse in the acousto-optic cell to diffract and focus the input beam into a resonating high-Q mode. When the rf acoustic pulse is not wholly within the cell, the beam is diverted to the output. A reflective surface is placed on the cell to yield only one output beam and to yield a retroflective beam back into the cavity for a high Q condition whenever a correctly generated chirp acoustic wave is in the proper postion within the cell.

Energy Technology Data Exchange (ETDEWEB)

The utilization of electrically heated rods for the simulation of nuclear fuel pins represents a generally adopted method by the nuclear industry to study thermalhydraulic problems. Usually its is necessary to determine the time variation of the electric linear power to simulate a given nuclear power transient in order to yield the same temperature and heat flux conditions in the surface of the electrical heater that would be observed in the nuclear fuel pin. The present work analyzes the limits of the usually adopted simulation methods and shows a manner to obtain the required electrical linear power that reduces oscillations and yields accurate results for the thermal conditions of the rod surface wall. (author). 5 refs, 5 figs, 1 tab.

International Nuclear Information System (INIS)

We show how the formulation of the matrix models as conformal field theories on a Riemann surfaces can be used to compute the genus expansion of the observables. Here we consider the simplest example of the Hermitian matrix model, where the classical solution is described by a hyperelliptic Riemann surface. To each branch point of the Riemann surface we associate an operator which represents a twist field dressed by the modes of the twisted boson. The partition function of the matrix model is computed as a correlation function of such dressed twist fields. The perturbative construction of the dressing operators yields a set of Feynman rules for the genus expansion, which involve vertices, propagators and tadpoles. The vertices are universal, the propagators and the tadpoles depend on the Riemann surface. As a demonstration we evaluate the genus-two free energy using the Feynman ...

Energy Technology Data Exchange (ETDEWEB)

A compact cesium deposition system was used for direct deposition of cesium atoms and ions onto the inner surface of the 1/3 scale Hydrogen Negative Ion Source for the LHD-NBI system. A small, well defined amount of cesium deposition in the range of 3-200 mg was tested. Negative ion extraction and acceleration were carried out both in the pure hydrogen operation mode and in the cesium mode. Single Cs deposition of 3-30 mg to the plasma chamber have produced temporary 2-5 times increases of H-yield, but the yield was decreased within several discharge pulses to the previous steady-state value. Two consecutive 30 mg depositions done within a 3-5 hours/60 shot interval, produced a similar temporary increase of H-beam, but reached a larger H-yield steady-state value. Deposition of larger 0.1-0.2 g Cs portions with a 20-120 hours/150-270 shot interval improved the H-yield for a long (2-5 ...

Energy Technology Data Exchange (ETDEWEB)

The resonance reaction /sup 11/B(p,/alpha/)/sup 8/Be was used to determine the boron profiles in the surface of: (1) boron implanted silicon; (2) boron diffused silicon; and (3) boron containing films deposited on silicon wafers. The boron distribution in the various samples was found to be stable under the bombardment of the proton beam. The convolution process used to obtain yield curves from the depth distribution, and the program used for this purpose are described.

Energy Technology Data Exchange (ETDEWEB)

Gas and plasma nitriding processes were executed in the magnesium with modification by titanium in search for an effective surface treatment method for magnesium alloys. Magnesium-nitrogen system has completely no solid solution or solubility, so that nitride should be only formed by eutectic reaction in the liquid phase. Hence, magnesium is difficult or nearly impossible to have its surface modified by nitriding. Addition of nitride forming element into magnesium enables us to lower the onset temperature of nitriding. Magnesium-titanium alloys with 1 to 5 wt% are yielded by the bulk mechanical alloying and, subjected to gas nitriding for various process conditions. Successful co-formation of Mg{sub 3}N{sub 2} as well as TiN becomes a proof to demonstrate the possibility of gas/plasma nitriding in the solid-state magnesium with aid of nitride former. (orig.)

British Library Electronic Table of Contents (United Kingdom)

In this paper we present the results of time series analysis for a coal mining region based on partial unmixing. We test the method also known as mixture tuned matched filtering on an eight image Landsat 5 TM and Landsat 7 ETM+ time series covering the period from 1987 to 2003. Common change detection methods often include the comparison of two interactively generated classification results, such as derived from Maximum Likelihood classification. These approaches often yield highly accurate results. However, disadvantages include a strong analyst bias and hardly repeatable results. For a quantitative monitoring of a single surface class' development over time they are often not recommendable. Our goal was to test an unbiased quantitative way to assess the development of coal surfaces, such...

CERN Document Server

In the beam pipe of the positron damping ring of the Next Linear Collider, electrons will be created by beam interaction with the surrounding vacuum chamber wall and give rise to an electron cloud. Several solutions are possible for avoiding the electron cloud, without changing the bunch structure or the diameter of the vacuum chamber. Some of the currently available solutions for preventing this spurious electron load include reducing residual gas ionization by the beam, minimizing beam photon-induced electron production, and lowering the secondary electron yield (SEY) of the chamber wall. We will report on recent SEY measurements performed at SLAC on TiN coatings and TiZrV non-evaporable getter thin films.

Energy Technology Data Exchange (ETDEWEB)

The Ti-6Al-4V alloy was treated by inductively coupled rf plasma nitriding. The effects of plasma-processing time in the range of 5-35 min on the microstructure and the mechanical properties of the plasma-nitrided Ti-6Al-4V samples were studied. The plasma power input was adjusted at 450 W and pure N{sub 2} gas was introduced to establish a treatment pressure of 8.0-8.4 x 10{sup -2} mbar. The characteristics of the nitrided layers have been investigated by microhardness testing, surface roughness measurements, optical microscopy, and x-ray diffraction. The results show that the surface microhardness increases as the plasma-processing time increases to reach 2000 HV0.1 at a plasma-processing time of 35 min. A high nitriding rate of 2.81 {mu}m{sup 2} s{sup -1} at a plasma-processing time of 25 min was achieved. The formation of the hard phases TiN, Ti{sub 2}N, and Ti(N) in the Ti-6Al-4V surfaces are found to be the reason for ...

Energy Technology Data Exchange (ETDEWEB)

Transient experiments in a Temporal Analysis of Products (TAP) Reactor were performed to elucidate the role of surface oyxgen species in the oxidation of benzene to phenol on ZSM-5 type zeolites with nitrous oxide as a selective oxidant. It was shown by puls experiments with nitrous oxide that the mean lifetime of the generated surface oxygen species is between 0.2s at 500 C and about 4.2 s at 400 C. Afterwards the surface oxygen species desorb as molecular oxygen into the gas phase where total oxidation will take place if hydrocarbons are present. Dual puls experiments consisting of a nitrous oxide puls followed by a benzene puls allowed studying the reactivity of the surface oxygen species formed during the first puls. The observation of the phenol formation was impeded due to the strong sorption of phenol. Multipulse experiments were necessary to reach a pseudo steady state phenol ...

Energy Technology Data Exchange (ETDEWEB)

A concentrator which contains mirrors installed on a carrier frame by means of hinges is described. In order to improve the performance of a concentrator it contains a mechanism for controlling radiation density in a form of a screw attached to the carrier frame. It also contains a circular sliding coupling on the frame which has an annular groove with levers placed in it. The mirrors are connected to the sleeve by means of the levers, and the hinges are made cylindrical and have axes that are perpendicular to the axes of the screw.

British Library Electronic Table of Contents (United Kingdom)

Excessive use of poultry litter (PL) on agricultural land is known to cause eutrophication of surface waters. Consequently, both poultry producers and PL users have to meet strict state and federal guidelines on litter storage and land application. This study examined the environmental benefits of adding lime, alum, ferrous sulfate, fly ash (FA), fluidized bed ash (FBA) and soil fix (SF) to PL for immobilizing excess phosphorus (P) while providing sufficient nutrients for proper growth of soybean [Glycine max (L.)] and corn [Zea mays (L.)] on a rotation. Amending PL with lime, alum, SF, FA and FBA significantly (p>0.05) increased corn and soybean yield. In contrast control plots that received a 10-10-10 (N-P2O5-K2) fertilizer showed lower yield and corn quality. Increased yield was ob...

Energy Technology Data Exchange (ETDEWEB)

Taiheiyo coal deashed using acid treatment and loaded with potassium or calcium was hydro-cracked under gaseous phase to discuss effects of these metals on liquefaction reaction. In addition, the loaded coal was added with red mud catalyst to examine effects of the addition. The loaded potassium has a softening power, and particularly the potassium adsorbed into surface and micropores in the coal decomposes selectively HI-BS and BI-PS and generates gas and HS. On the other hand, potassium deposited on coal surface promotes direct gas production from the coal. Irrespective of its loading modes, calcium has a catalytic nature to produce HI-BS selectively. Calcium also acts to impede decomposition of HI-BS into HS. Adding red mud catalyst to potassium loaded coal increases the inversion rate and the liquefaction yield, and most of the increase is accounted for by HI -BS, and BI-PS. When red mud catalyst is added to calcium ...

Energy Technology Data Exchange (ETDEWEB)

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

Energy Technology Data Exchange (ETDEWEB)

The polymerization of vinyl pyrrolidinone on nylon 66, with the assistance of aqueous phenol and formic acid, was investigated by mutual and post irradiation procedures. Both solvents were found to greatly facilitate the polymerization with the post irradiation procedure, whereas neither presented any advantage with the mutual irradiation procedure. Tensile properties of the modified fibers were affected in similar ways by both the irradiation procedures and solvents in that the only notable changes were the somewhat higher extensions at yield and at break. The moisture regain values of the treated yarns and fabrics were increased up to three-fold. Surface morphology of the modified fibers was revealed by SEM.

International Nuclear Information System (INIS)

Data for the excitation of the 2_1"+ and 2_2"+ states in the "8"8Sr(p,p') reaction at 25 and 31 MeV indicate sustantial contributions from the interior of the nucleus, Microscopic DWBA calculations reproduce this and yield a fair description of the data. A detailed description, especially of the 2_2"+ state, is sensitive to the effective nucleon-nucleon interaction used and the non-locality of the optical potential, which are insufficiently known at present. (orig.).

Energy Technology Data Exchange (ETDEWEB)

An investigation on the hydrogen generation by reacting ball-milled Mg-based materials in different alcoholic solutions (methanol, ethanol, 2-propanol) was performed. The MgH{sub 2} reactivity in methanol is very low (maximum conversion yield <10%) and no improvement is induced by the ball milling treatment. In contrast, the ball milling affects greatly the Mg reactivity in methanol. The Mg powder milled for 30min displays a maximum conversion yield of 47% compared to 3% for unmilled Mg powder. Its high reactivity is ascribed to the creation of numerous defects and fresh surfaces during the initial stage of the milling process, favoring the corrosion of Mg in methanol. In addition, the presence of water in the methanol solution inhibits drastically the alcoholysis reaction despite its low amount (0.3vol%). The higher hydrogen production is obtained with the composite Mg-10at% Ni milled for 30min leading to a ...

Energy Technology Data Exchange (ETDEWEB)

The main goal of this research is to delineate the wetting behavior of coal and it subsequent effects on fine coal processing. As both bulk and surface properties of coal are interrelated and have a controlling role on the performance of these processes, a detailed study has been undertaken to correlate their influence on both wetting behavior and the response of coal to flotation and other unit operations encountered in fine coal processing. During the last quarter, the effect of coal rank on water retention capacity was investigated. The effect of pH on the vacuum flotation yield and the effect of desliming on the film flotation response of coal were also studied. 6 refs., 5 figs.

British Library Electronic Table of Contents (United Kingdom)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr2N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30-35wt%) Ni-Cr alloys and a ferritic high Cr (29wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effect...

Energy Technology Data Exchange (ETDEWEB)

The manual provides design information for four groups of sediment control structures and treatments which are suitable for use on small areas in surface coal mining. A detailed design procedure is given for each group which will estimate the total amount of settleable solids from a small area with a sediment control structure or treatment for a specific design storm. A procedure is also given for estimating the mean annual sediment yield from a small area. Information on design, installation, maintenance and cost is given for each sediment control measure. Methods for determining the maximum allowable area for each sediment control measure and for design of combined sediment control systems are presented. The design procedures contain numerous nomographs, graphs, and worksheets to facilitate the use of the design procedure. The sediment control measures, design procedures, and materials in the manual are applicable to coal bearing regions of ...

Energy Technology Data Exchange (ETDEWEB)

The possibility of a positive agricultural use of flue gas filter ash from brown coal power plants is investigated. The suggested measure is mixing ash dump surfaces with extremely acidic spoil bank soils, which balances the high pH value of the alkaline ash and contributes to improved nutrient and soil sorptive conditions. Optimum quantity of spoil bank sands in the mixture with ash is between 10% and 40%. The optimum quantity must be determined for each type of ash considering improvement of soil chemical conditions and water retention capacity. Filter ash properties vary widely; the required amount of spoil bank sand added to investigated ash surfaces near 3 brown coal power plants was between 25% and 30% of the mixture. The same favourable soil and ash mixture can be produced by adding 60% to 75% filter ash to acidic raw spoil bank soil surfaces forming a top soil layer in a thickness of minimum 60 cm. Tests of plant ...

Energy Technology Data Exchange (ETDEWEB)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a {sup 137}Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 {+-} 0.9 cm{sup 2} y{sup -1}, is in good agreement with the values quoted by other ...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), loading collapse ...

International Nuclear Information System (INIS)

Molecular beam epitaxy (MBE) grown Ge nanodots are found to come in a clear trimodal island distribution of huts, pyramids, and domes when grown on (001)Si at 550 deg. C. The island types appear in this order as Ge coverage increases and for a certain coverage all three types are found to coexist at this growth temperature. Previously Ge nanodots have mostly been divided into huts and domes at growth temperatures below 600 deg. C, or pyramids and domes above 600 deg. C. The (105) faceted pyramidal and elongated huts and the multifaceted domes are well known, but a distinction has not previously been seen between huts and a separate size distribution of similarly (105)-faceted pyramidal nanodots twice the size of huts, at temperatures below 600 deg. C. The 20-25 nm wide huts also appear to be the smallest obtainable self-assembled Ge dots on (001)Si, in accordance with predictions based on Si_1_-_xGe_x nanodots on (001)Si. They are about a ...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of scale-up studies to determine the feasibility of extending the nitridation approach to thin 0.1mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. As-treated Fe-20Cr-4V foil exhibited target (low) ICR values, whereas 2205 foil suffered from run-to-run variation in ICR values, ranging up to 2x the...

Energy Technology Data Exchange (ETDEWEB)

The recent definition of a postulated thermal shock accident followed promptly by system repressurization, termed an overcooling or pressurized thermal shock accident, has set a large analysis and research effort into motion. The essential elements are concerned with defining the accident transients, evaluating the instrumentation and controls that cause the postulated accidents, and evaluating the metallurgical and structural mechanics aspects of the reactor vessel with respect to its failure potential. This paper poses the question faced by the Nuclear Regulatory Commission (NRC) for the vessel steel embrittlement, annealing, and surveillance dosimetry facets of this postulated accident and provides information on our plans for study of this problem as well as current status.

Science.gov (United States)

Lumbar epidural anesthesia is useful in a variety of chronic benign pain syndromes, including lumbar radiculopathy, low back pain syndrome, spinal stenosis, and vertebral compression fractures. Given the increased number of epidural nerve blocks being performed, some have reported unexplained complications of a transient or permanent nature and with varying degrees of severity. However, no case has been reported of a broken epidural needle tip retained in the lumbar facet joint area. This represents the first reported case presentation of foraminal stenosis developing in a patient after a retained epidural needle tip. PMID:21286465

International Nuclear Information System (INIS)

A container experiment was conducted to test the hypothesis that uncomposted wool wastes could be used as nutrient source and growth medium constituent for container-grown plants. The treatments were: (1) rate of wool-waste application (0 or unamended control, 20, 40, 80, and 120 g of wool per 8-in. pot), (2) growth medium constituents [(2.1) wool plus perlite, (2.2) wool plus peat, and (2.3) wool plus peat plus perlite], and (3) plant species (basil and Swiss chard). A single addition of 20, 40, 80, or 120 g of wool-waste to Swiss chard (Beta vulgaris L.) and basil (Ocimum basilicum L.) in pots with growth medium provided four harvests of Swiss chard and five harvests of basil. Total basil yield from the five harvests was 1.6-5 times greater than the total yield from the unamended control, while total Swiss chard yield from the four harvests was 2-5 times greater relative to the respective unamended control. The addition ...

Energy Technology Data Exchange (ETDEWEB)

The pure xenon dc positive column discharge has been characterized for various xenon pressures, currents, and discharge tube radii. The absolute output at the 147 nm resonance transition has been measured using two independent techniques to yield the radiant emittance at 147 nm (power per unit surface area). The efficiency of 147 nm production is obtained by combining the measured radiant emittance with the measured electrical power per unit length deposited in the gas. The radiant emittance and the efficiency are the two principle figures of merit for characterizing the discharge as a source of VUV radiation. It is observed that the trends in efficiency and radiant emittance change substantially when the discharge transitions from two-step electron impact excitation/ionization at higher pressures to single-step electron impact ionization at lower pressures. Modeling of the xenon positive column discharge yields radiant ...

Energy Technology Data Exchange (ETDEWEB)

The simultaneous biosorption of Cr(VI) and Cu(II) on free Rhizopus arrhizus in a packed column operated in the continuous mode was investigated and compared to the single metal ion situation. The breakthrough curves were measured as a function of feed flow rate, feed pH, and different combinations of metal ion concentrations in the feed solutions. Column competitive biosorption data were evaluated in terms of the maximum (equilibrium) capacity in the column, the amount of metal loading on the R. arrhizus surface, the adsorption yield, and the total adsorption yield. In the single-ion situation the adsorption isotherms were developed for optimum conditions, and it was seen that the adsorption equilibrium data fit the noncompetitive Freundlich model. For the multicomponent adsorption equilibrium the competitive adsorption isotherms were also developed. The competitive Freundlich model for binary metal mixtures represented ...

Energy Technology Data Exchange (ETDEWEB)

Swift heavy ion-solid interaction leads in volume to track creation and on the surface to the ejection of particles into the vacuum. To learn more about initial mechanisms of track formation, we are focused on the sputtering of uranium dioxide by fast heavy ions. This present study is exclusively devoted to the influence of the electronic stopping power on the emission of neutral particles and especially on their angular distribution. These measurements are completed by those of the ions emitted from UO{sub 2} targets bombarded with swift heavy ions. The whole experimental results give access to: i) the nature of the sputtered particles; ii) the charge state of the emitted particles; iii) the direction of ejection of the sputtered particles ; iv) the sputtering yields deduced from the angular distributions. These results are compared to the prediction of the sputtering models proposed in the literature and it seems that the supersonic gas flow ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

British Library Electronic Table of Contents (United Kingdom)

Fluoroalkyl end-capped vinyltrimethoxysilane oligomer suffered the sol-gel reaction under alkaline conditions in the presence of titanium oxide nanoparticles in tetrahydrofuran to afford the corresponding fluorinated oligomer/titanium oxide nanocomposites[RF-(VM-SiO2)n-RF/TiO2] in excellent to moderate isolated yields. These fluorinated composites thus obtained were nanometer size-controlled fine particles, and exhibited good dispersibility and stability in traditional organic solvents except for water. These fluorinated nanocomposites were applied to the surface modification of glass to exhibit not only a completely superhydrophobic characteristic (a water contact angle: 180degree) with a non-wetting property against water droplets but also a good oleophobicity imparted by fluoroalkyl seg...

British Library Electronic Table of Contents (United Kingdom)

TiO2 hollow microspheres with sea urchin-like hierarchical architectures were synthesized by a simple hydrothermal method. The as-synthesized hollow microspheres with hierarchical architectures consisting of many rhombic building units exhibit high specific surface area. Electrorheological (ER) properties of hierarchical hollow TiO2-based suspension were investigated under steady and oscillatory shear. The hollow TiO2-based suspensions show much higher yield stress and elasticity than pure TiO2 suspension at the same electric field strength. This phenomenon was elucidated well in view of their dielectric spectra analysis. The sea urchin-like architectures result in stronger interfacial polarization of hollow TiO2 suspension upon an electric field, showing higher ER activity. Also, hollow i...

Energy Technology Data Exchange (ETDEWEB)

The probability of damage and the potential resulting hazards are analyzed for a representative rail shipping container for three severe rail accident scenarios. The scenarios are: (1) the rupture of closure bolts and resulting opening of closure lid due to a severe impact, (2) the puncture of container by an impacting rail-car coupler, and (3) the yielding of container due to side impact on a rigid uneven surface. The analysis results indicate that scenario 2 is a physically unreasonable event while the probabilities of a significant loss of containment in scenarios 1 and 3 are extremely small. Before assessing the potential risk for the last two scenarios, the uncertainties in predicting complex phenomena for rare, high- consequence hazards needs to be addressed using a rigorous methodology.

Energy Technology Data Exchange (ETDEWEB)

Microalloyed or high strength low alloy (HSLA) steels are carbon-manganese steels containing small amounts of Nb, V or Ti. The excellent mechanical properties of these alloys, particularly high yield strength, usually obviate the need for expensive quench and tempering operations. Furthermore, the presence of a significant amount of nitride-forming elements in some microalloyed steels has generated interest in the applicability of these alloys as a new generation of nitriding steels. In this paper, a study of the plasma nitriding behaviour of a commercially available microalloyed steel MAXIMA{sup TM} is reported. A comparison is made with a traditional quenched and tempered nitriding steel (En19), plasma nitrided under similar conditions. Optical and scanning electron microscopy in conjunction with microhardness measurements and X-ray diffraction were utilized to characterize the nitrided surfaces. The observed differences in the thickness and ...

International Nuclear Information System (INIS)

Modeling is performed for focused-ion-beam (FIB) sputtering and redeposition on trench sidewalls in a steady state approximation. Calculations are carried out to demonstrate the sputtered surface profile under known parameters such as sputtering yield as a function of ion incident angle, the FIB current density profile, and the FIB scan speed. It is found that a steplike slope with a gradient angle of #theta#_0 is formed at the FIB bombarding position. Furthermore, the redeposition flux on the sidewalls is calculated as a function of #theta#_0 for the FIB trench milling assuming the cosine law for the angular distribution of the sputtered atom. The redeposition will be more accurately predictable and controllable when more information about these assumptions is obtained.

British Library Electronic Table of Contents (United Kingdom)

Bent specimens of A533B steel (0.16wt% Cu) were irradiated at 290degreeC to 1dpa with 6.4MeV Fe3+ ions. Calculated tensile stresses at the irradiated surface were set to 0, 250, 500 and 750MPa. The specimens were subjected to hardness measurements, transmission electron microscopy (TEM) observations and three-dimensional atom probe (3DAP) analysis. The radiation-induced hardening decreased with increasing stress to 500MPa which was near the yield strength. TEM and 3DAP results showed that well-defined dislocation loops and solute clusters were formed. The diameter of dislocation loops increased and the number density decreased when the stress was applied, whereas the diameter and number density of solute clusters decreased. The hardening was mainly attributed to solute cluster formation. A...

DEFF Research Database (Denmark)

Zinc oxide (ZnO) and alumina (Al2O3) particles are synthesized by the combustion of their volatilized acetylacetonate precursors in a premixed air-methane flame reactor. The particles are characterized by XRD, transmission electron microscopy, scanning mobility particle sizing and by measurement of the BET specific surface area. Pure (?-)alumina particles appear as dendritic aggregates with average mobile diameter 43-93 nm consisting of partly sintered, crystalline primary particles with diameter 7.1-8.8 nm and specific surface area 184-229 m2/g. Pure zinc oxide yields compact, crystalline particles with diameter 25-40 nm and specific surface area 27-43 m2/g. The crystallite size for both oxides, estimated from the XRD line broadening, is comparable to or slightly smaller than the primary particle diameter. The specific surface area increases and the primary particle size decreases ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steels can yield low interfacial contact resistance (ICR), electrically-conductive and corrosion-resistant nitride containing surfaces (Cr2N, CrN, TiN, V2N, VN, etc) of interest for fuel cells, batteries, and sensors. This paper presents the results of scale up studies to determine the feasibility of extending the nitridation approach to thin 0.1 mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. A major emphasis was placed on selection of alloy foil composition and nitidation conditions potentially capable of meeting the stringent cost goals for automotive PEMFC applications. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. Promising behavior was observed under simulated aggressive anode- and cathode- side bipolar plate conditions ...

British Library Electronic Table of Contents (United Kingdom)

We present a forward modelling technique for calculating the surface X-ray spectra for a variety of lunar terrains. Our calculations considered variations in solar fluxes from solar quiescent condition to large flare activity (M1 flare), and expected elemental concentrations in the target, as well as yield, instrumental, and viewing geometry parameters for X-ray induced fluorescence from the lunar surface. Additionally, we present estimates of anticipated XRF signals from prominent Ka lines observable by a collimated 14cm2 X-ray detector from a 100km lunar orbit with 20km spatial resolution. Our results show that Mg, Al and Si characteristic Ka lines can be observed for all solar conditions. The Ca Ka lines line can be differentiated from a fixed background during more energetic solar cond...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited...

Energy Technology Data Exchange (ETDEWEB)

Reductive quenching of two photoexcited ruthenium(II) complexes by an anionic electron donor, 2,2{prime}-azinobis(3-ethyl-benzothiazoline-6-sulfonate) (ABTS{sup 2{minus}}), in aqueous solution was examined by laser flash photolysis before and after adding positively charged colloidal (250-{angstrom} diameter) alumina-coated silica particles. The kinetics and quantum yields of electron transfer with an anionic sensitizer, RuL{sub 3}{sup 4{minus}} (L = bathophenanthroline disulfonate), and a cationic one, Ru(bpy){sub 3}{sup 2+} (bpy = 2,2{prime}-bipyridine), were compared. Coadsorption of ABTS{sup 2{minus}} and RuL{sub 3}{sup 4{minus}} by the particles greatly enhanced the rate of quenching such that only the reaction occurring on the surfaces of the particles was observed. Electron transfer from ABTS{sup 2{minus}} to RuL{sub 3}{sup 4-*} occurred by a static (nondiffusional) process, and the quenching efficiency was maximal when there was close ...

Energy Technology Data Exchange (ETDEWEB)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr{sub 2}N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30-35 wt%) Ni-Cr alloys and a ferritic high Cr (29 wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni-Cr base alloys, but beneficial effects for the stainless steel alloy. Positive results from single-cell fuel cell ...

International Nuclear Information System (INIS)

Ozone formation by a pulse positive corona discharge generated in the gas phase between a planar high voltage electrode made from reticulated vitreous carbon and a water surface with an immersed ground stainless steel plate electrode was investigated under various operating conditions. The effects of gas flow rate (0.5-3 litre min"-"1), discharge gap spacing (2.5-10 mm), applied input power (2-45 W) and gas composition (oxygen containing argon or nitrogen) on ozone production were determined. Ozone concentration increased with increasing power input and with increasing discharge gap. The production of ozone was significantly affected by the presence of water vapour formed through vaporization of water at the gas-liquid interface by the action of the gas phase discharge. The highest energy efficiency for ozone production was obtained using high voltage pulses of approximately 150 ns duration in Ar/O_2 mixtures with the maximum efficiency (energy ...

International Nuclear Information System (INIS)

Radiation hardening in austenitic stainless steels is shown to modify deformation characteristics and correlate well with an increased susceptibility to intergranular stress corrosion cracking (IGSCC). Available data on neutron-irradiated materials have been analyzed and correlations developed between fluence, yield strength and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 to 2.5 x10"2"1 n/cm"2) for IGSCC are documented. In many cases, this variability is consistent with yield strength differences among irradiated materials. IGSCC correlates better to yield strength than to fluence for most heats suggesting a possible role of radiation-induced hardening and microstructure on cracking. Microstructural evolution during proton and heavy-ion irradiation has been characterized in low-carbon 304SSs. Hardening results from a dispersion of dislocation ...

Energy Technology Data Exchange (ETDEWEB)

Single and binary metal molybdates of the formula AMoO{sub 4}, where A=Ni, Co, Mg,Mn and/or Zn, were investigated for the oxydehydrogenation of propane to propylene, as well as some ternary molybdates of the formula NiO{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4} where X=P, Bi, Fe, Cr, V and Ce. All catalysts were supported on SiO{sub 2} with an active phase/support ratio of 80/20 (wt%). The reaction is catalytic and not a gas phase initiated reaction. It is first order in propane, consistent with the abstraction of the methylene hydrogen being the rate limiting step. Propane conversions and propylene yields vary greatly depending on the metal of the molybdate and surface area of the catalyst. Highest propylene yields (16% at 26.6% propane conversion) are obtained with NiMoO{sub 4}/SiO{sub 2}. Conversion and yield are significantly influenced by the molybdenum content of the compositions. The effect is ...

Energy Technology Data Exchange (ETDEWEB)

The major focus of this oil-shale investigation has been on specific localities of oil-shale resource potential. Three main areas of oil-shale occurrence have been studied in detail: the Elko area, Pinon Range area, and Coal Mine Canyon. Geologic mapping, stratigraphic studies, and sampling to delimit the lateral extent of the oil shale deposits were in progress prior to the cooperative agreement with Nevada DOE. These surface geologic studies have been summarized in this report. The results of surface geologic studies conducted near Elko suggested that the Elko area represented the best and most accessible oil-shale deposits; therefore, the Elko area was selected as the site of a shallow exploratory drilling program. Essential to this study was the obtaining of fresh, unweathered oil-shale samples from the Elko area. The samples were obtained from the core-drilling program and tested for oil yield by Fischer assays. The ...

Energy Technology Data Exchange (ETDEWEB)

As part of studies into the siting of a deep repository for nuclear waste, Swedish Nuclear Fuel and Waste Management Company (SKB) has commissioned the Alternative Models Project (AMP). The AMP is a comparison of three alternative modeling approaches for geosphere performance assessment for a single hypothetical site. The hypothetical site, arbitrarily named Aberg is based on parameters from the Aespoe Hard Rock Laboratory in southern Sweden. The Aberg model domain, boundary conditions and canister locations are defined as a common reference case to facilitate comparisons between approaches. This report presents the results of a discrete fracture pathways analysis of the Aberg site, within the context of the SR 97 performance assessment exercise. The Aberg discrete fracture network (DFN) site model is based on consensus Aberg parameters related to the Aespoe HRL site. Discrete fracture pathways are identified from canister locations in a prototype repository design to the ...

Science.gov (United States)

The main facets of professor N.I. Pirogov's professional activity are outlined. Forensic medicine (in the first place its organizational and practical aspects) was an integral component of his scientific and clinical work, along with applied anatomy and surgery. Landmark publications of N.I. Pirogov are listed with special reference to those concerned with forensic medical expertise of medical malpractice cases, postmortem inspection and intravital examination procedures, wound ballistics studies, the atlas of forensic pathology, etc. The surgeon and anatomist N.I. Pirogov can be justly regarded as a founder of forensic medicine in this country. PMID:21866839

British Library Electronic Table of Contents (United Kingdom)

In this paper we demonstrate the electrodeposition of nickel, a common ferromagnetic material, in various magnetically desirable shapes including nanowires, nanoparticles and highly faceted shells. In order to obtain three dimensional mesostructures, the electrochemical deposition of nickel was performed on highly oriented pyrolytic graphite (HOPG) under different electrolyte composition and deposition potential conditions. Under potentiostatic deposition at one distinct potential negative with respect to the reversible potential of nickel, three stages of nucleation and growth take place leading to a complex morphology of deposits. However, dual-pulse potential deposition and electrodeposition in low pH solutions causing hydrogen evolution, lead to nickel deposits in the form of nanowires...

Energy Technology Data Exchange (ETDEWEB)

Buried ridge stripe lasers have been grown on InP in two steps by gas source molecular beam epitaxy. The active structure consists of a compressively strained layer multi quantum well with an equivalent wavelength emission at 1.5 [mu]m. The stripe was defined by reactive ion etching. A threshold current of 22 mA was reproducibly obtained on a laser length of 500 [mu]m. A CW output power of 48 mW per facet was achieved. In addition, preliminary accelerated aging tests have shown the high reliability the structure. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This report describes the experimental researches on the polarization Characteristics of symmetric GaAs-GaAlAsP double heterojunction lasers, and analyses the mode-competition processes of these lasers. The experiments showed that semiconductor laser is emitted spontaneously and does not indicate optical polarization characteristic when it is biased under the threshold current. When it is biased above the threshold current, the laser for thin active layer of d = 0.15approx.0.40 ..mu..m is generally observed only in fundamental order mode, and TE mode polarization is predominant. At this time, polarization selection is dependent on Fabry-Perot cavity facet (cleaved face) mode reflectivity R/sub 0/. But TM mode is saturated at the threshold, the current applied to the laser above the threshold is used to enhance the TE polarization when the active thickness d is larger than 0.4 ..mu..m, the competition between TE and TM mode, fundamental order an higher order mode ...

Energy Technology Data Exchange (ETDEWEB)

We study the surface and interface roughness of a two-liquid film system using neutron reflectometry. The middle phase and bottom phase are extracted from a three-phase microemulsion containing 2 wt% non-ionic surfactant C{sub 10}E{sub 4}, 81 wt% D{sub 2}O and 17 wt% octane (C{sub 8}H{sub 18}). The system is formed by spreading a few drops of the middle phase of the microemulsion on the bottom phase of the microemulsion. The middle phase does not wet the bottom phase, but demixes to form a top octane-water mixture layer with a thickness of {proportional_to}580 A. The mean surface roughness of the system is found to be 7 A but the data are insensitive to interface roughness. An extended capillary wave model for a two-liquid-film system is derived to account for the coupling between the surface and interface. The dispersion relation yields two fundamental modes. In a calculation of mean-square roughness ...

Energy Technology Data Exchange (ETDEWEB)

We have demonstrated in this work (1) that methane is readily activated at mild conditions (100{degree}C, 1 torr) over a relatively noble metal, Pd. This was observed using a stepped and kinked Pd(679) crystal (1), and other crystal faces are now being investigated to establish whether the cracking of the C-H bond of methane on Pd is structure sensitive or structure insensitive. Oxygen chemisorption is extremely structure sensitive: weakly bonded, highly reactive oxygen overlayers form on Pd(100) surface (2), while strongly bonded, moderately reactive oxygen overlayers form on Pd(111) and Pd(679). Reaction of the weakly bonded oxygen with surface carbide gives rise to CO{sub 2} over clean Pd(100) but to CO over halogen-doped Pd(100) (3--5). The effect of halogens is primarily ensemble-controlling, or oxygen-supply restricting, but long range influence of surface Cl on the strength of the Pd-O bond has also been observed ...

Science.gov (United States)

In this paper, we evaluate the performance of the 1- and 5-site models of methane on the description of adsorption on graphite surfaces and in graphitic slit pores. These models have been known to perform well in the description of the fluid-phase behavior and vapor-liquid equilibria. Their performance in adsorption is evaluated in this work for nonporous graphitized thermal carbon black, and simulation results are compared with the experimental data of Avgul and Kiselev (Chemistry and Physics of Carbon; Dekker: New York, 1970; Vol. 6, p 1). On this nonporous surface, it is found that these models perform as well on isotherms at various temperatures as they do on the experimental isosteric heat for adsorption on a graphite surface. They are then tested for their performance in predicting the adsorption isotherms in graphitic slit pores, in which we would like to explore the effect of confinement on the molecule packing. ...

Energy Technology Data Exchange (ETDEWEB)

A prediction of delayed neutron yields for actinides which are important in the nuclear energy field is given. The prediction is based on a correlation related to a suggested cluster structure of the nucleus. (author).

Energy Technology Data Exchange (ETDEWEB)

The objective of this study is to evaluate the lifetime of Zr-2.5Nb pressure tube at Wolsung Unit-1. The testing materials (Effective full power year: 9.3 year, Accumulated nuetron fluence: 7.66{approx}8.91 x 1025 n/m{sup 2}) were sampled from M-11 tube at various position(inlet, middle and outlet). The cutting was carried out at hot cell to fabricate CT(Compact tension) specimen with 48 ppm hydrogen content. In the result of DHC test, irradiation-damaged specimen showed 4{approx}6 times faster DHC velocity(5.298E-0.8{approx}7.039E-8 m/s: 182 .deg. C) than non-irradiated specimen. These DHCV results also show slight faster than one of specimen from Pickering plant (average DHCV: 4.5E-8 m/s: 182 .Deg C). This faster DHCV can be explained with the fact that Wolsung Unit-1 have been operated in a severe conditions(higher cooling water temperature, high power and efficiency) than Pickering one. The striation spacing which was seen DHC fracture surface at irradiated ...

Energy Technology Data Exchange (ETDEWEB)

The preparation and performance of membranes for application to hydrogen separation from coal-derived gas is described. The membrane material investigated was dense amorphous silica deposited on a suitable support by chemical vapor deposition (CVD). Two types of support materials were pursued. One type consisted of a two-layer composite, zeolite silicalite/{alpha}-Al{sub 2}O{sub 3}, in the form of tubes approximately 0.7 cm in diameter. The other type was porous glass tubes of diameter below 0.2 cm. The first type of support was prepared starting from {alpha}-Al{sub 2}O{sub 3} tubes of 1{micro}m mean pore diameter and growing by hydrothermal reaction a zeolite silicalite layer inside the pores of the alumina at the OD side. After calcination to remove the organic template used in the hydrothermal reaction, CVD was carried out to deposit the final silica layer. CVD was carried out by alternating exposure of the surface with silicon tetrachloride and water vapor. SEM ...

CERN Document Server

In the present study, applications of the SPH method to industrial related issues are considered by starting from an existing open source 2D SPH code, namely the SPHYSICS code, which offers an effective ground for numerical developments, which are performed in order to bring an answer to industrial problems, such as simulations of solid/fluid coupling in a free surface flow context. The purpose of the present paper is therefore to expose the numerical developments which yield an enhanced version (referred to as "SPHYSIC2") of the initial code. Firstly, the different features added to obtain the operational code needed for engineering applications are described, and so are the problems raised on this way, offering a kind of review of SPH methods for engineers. Secondly, the validation of the proposed code is partially presented with two well known but difficult test cases, namely the classical "dam break" and "wedge entry" problems. Thirdly, ...

Energy Technology Data Exchange (ETDEWEB)

Statistically based experimental designs were applied to optimize the fermentation process parameters for hydrogen (H{sub 2}) production by co-culture of Clostridium acidisoli and Rhodobacter sphaeroides with sucrose as substrate. An initial screening using the Plackett-Burman design identified three factors that significantly influenced H{sub 2} yield: sucrose concentration, initial pH, and inoculum ratio. These factors were considered to have simultaneous and interdependent effects. A central composite design and response surface analysis were adopted to further investigate the mutual interactions among the factors and to identify the values that maximized H{sub 2} production. The optimal substrate concentration, initial pH, and inoculum ratio of C. acidisoli to R. sphaeroides were 11.43 g/L sucrose, 7.13, and 0.83, respectively. Using these optimal culture conditions, substrate conversion efficiency was determined as 10.16 mol H{sub 2}/mol ...

CERN Document Server

Weak lensing measurements are entering a precision era to statistically map the distribution of matter in the universe. The most common measurement has been of the variance of the projected surface density of matter, which corresponds to the induced correlation in alignments of background galaxies. This measurement of the fluctuations is insensitive to the total mass content, like using waves on the ocean to measure its depths. But when the depth is shallow as happens near a beach, waves become skewed. Similarly, a measurement of skewness in the projected matter distribution directly measures the total matter content of the universe. While skewness has already been convincingly detected, its constraint on cosmology is still weak. We address optimal analyses for the CFHT Legacy Survey in the presence of noise. We show that a compensated Gaussian filter with a width of 2.5 arc minutes optimizes the cosmological constraint, yielding $\\Delta ...

International Nuclear Information System (INIS)

Differentiating a benign from a malignant lesion by information such as density data, or signal intensities or echo gradients, is not possible with CT, nor MRI, nor ultrasonography. Only some lesions show characteristic signs. Inflammations cannot be difscriminated from malignant tumors. CTs of small tumors in particular are so poor in contrast that it is much more difficult to detect tumors or discriminate them from other lesions, as compared to MR images or ultrasonographs. CT does not detect surface tumors, but is more sensitive than MRI or US in detecting discrete cortical bone lesions. The same applies to small calcified tumors. MRI however is most sensitive in detecting tumor volumes in the yellow marrow, and is the best modality for evaluation of extraossal extension of tumors. CT yields better results than MRI if applied for simultaneous screening of lymph node metastases in the lower neck. MRI frequently is spoilt by movement ...

Energy Technology Data Exchange (ETDEWEB)

Laser-assisted processing techniques, utilized to produce fine, metal grid patterns for high-efficiency solar cells, are being investigated, developed, and characterized. The work performed in the third quarter of this contract is detailed here. A preliminary economic evaluation has yielded the conclusion that laser-assisted pyrolysis of spun-on silver neodecanoate is the most promising of all the metallization techniques being investigated in this contract. Early adhesion problems have been solved by optimizing deposition parameters. Linewidth studies have been carried out as a function of laser power, scan speed, and film thickness. Preliminary solar cells have been fabricated and characterized using this metallization scheme. Silver neodecanoate films have also been decomposed using a pulsed uv laser and metal mask. A detailed study of the various models of localized surface temperature rise in silicon due to laser heating has been carried ...

International Nuclear Information System (INIS)

The development and successful application of a unique leak sealant formulation comprised of a mixture of graded, hollow ceramic microspheres, surface oxidized aluminum powder and saturated gibbsite suspension is described. The project was undertaken to address the escalating leakage from up to 15 small weld defects in the water reflector vessel, an integral component of the NRU (National Research Universal) reactor calandria. The reflector surrounds the reactor core with a neutron reflecting blanket of light water. Injection of the sealant is typically done with the reactor shutdown and the water reflector system operating normally, but can also be performed with the reactor at full power. The procedure is simple and effective. Individual treatments of as little as 125 ml of sealant (10 ppm in the 12,500 L system) have yielded leak reductions exceeding 2000 L/day. The accumulated leak reductions of several treatments now total 90% of the ...

Energy Technology Data Exchange (ETDEWEB)

A combined PVD/PECVD process for the vacuum deposition of titanium containing amorphous hydrogenated carbon films is described. Elemental compositions of the deposited films have been determined by in situ core level photoelectron spectroscopy (XPS). The long-term stability of the plasma process has been demonstrated. Target poisoning has not been observed. We have fabricated optical selective surfaces by the deposition of a-C:H/Ti multilayers onto aluminum substrates. Even though we have not optimized layer thicknesses and stoichiometries so far, the experimental results are promising: solar absorptance {alpha}{sub S} of 0.876 and thermal emittance {epsilon}{sub 100C} of 0.061 have been achieved yielding an optical selectivity sis defined as{alpha}{sub S}/{epsilon}{sub 100C} of 14.4. Accelerated aging tests of these coatings have demonstrated their aging stability: the service lifetime is predicted to amount to more than 25 years. Raman ...

Energy Technology Data Exchange (ETDEWEB)

The present work addresses an off-axis Cassegrain optical concentration system. The specific primary collector analyzed, a short focal length parabolic concentrator, is at the University of Florida`s Energy Park. A secondary hyperbolic reflective element was designed to redirect the solar radiation from the primary focal plane to an off-axis target on the polar axis of the primary concentrator. This ground level target will be required for planned experimental work. The analysis was performed using a numerical ray tracing procedure that incorporates both random and systematic errors due to slope and surface irregularities. The optimization process varied secondary element size, curvature, and offset angle, and yielded information required for optimum design. As a single secondary element was found impractical, three elements were designed for use at various time of the year. The numerical analysis predicts that typically 70 to 75 percent of the ...

International Nuclear Information System (INIS)

Paper describes a new procedure to synthesize a pharmaceutical containing "2"1"1At. "2"1"1At"- anion was found to bind strongly with Rh"3"+ cation complexing with a thio-ether ligand - 1,5,9,13-tetratiacyclohexadecane-3,11-diol (16-S4-diol). One made use of "1"3"1I isotope to seek for the optimal conditions of the reaction. The derived complexes were studied by means of the paper electrophoresis, the ion exchange, the surface chromatography. One studied the kinetics of "1"3"1I"- anion binding with Rh(16-S4-diol), the dependence of the yield of "1"3"1I-Rh(16-S4-diol) forming complex on the temperature. the acidity of the reaction mixture and the concentration of the reagents. On the basis of the determined conditions of the synthesis one prepared "2"1"1At-Rh(16-S4-diol) complex by more astatide ("2"1"1At"-) to the equivalent amounts of RhCl_3 and tetra-thio-ether (16-S4-diol). One studied its behaviour

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Surface temperature is measured with an infrared thermometer. Measuring Surface Temperature. Nine sample points are selected with a site of uniform land ...

Science.gov (United States)

Fundamental study of heat transfer augmentation of tube inside surface by cascade smooth surface-turbulence promoters

Energy Technology Data Exchange (ETDEWEB)

The gas phase high resolution spectroscopic study of weakly bound clusters can provide the information necessary to develop an intermolecular potential energy surface. This surface can then be used to better understand condensed phases. In this work, a tunable far infrared laser spectrometer is used to study weakly bound dimers produced in the newly developed continuous planar supersonic jet expansion apparatus. The water dimer is an extensively studied hydrogen bonded dimer. It undergoes several tunneling motions which result in splittings and perturbations of the rovibrational energy levels. A review is presented of much of the experimental and theoretical work done on water dimer, including a description of the combined fit of all the high resolution spectroscopic results by Coudert and Hougen. Also included is a discussion of the measurement of the K = 1 lower {yields} K = 2 lower band performed using the tunable far ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than untreated Fe-20Cr-4V, ...

Energy Technology Data Exchange (ETDEWEB)

We studied the interaction of Pu(VI) with Pseudomonas stutzeri ATCC 17588 and Bacillus sphaericus ATCC 14577, representatives of the main aerobic groups of soil bacteria present in the upper soil layers. The accumulation studies have shown that these soil bacteria accumulate high amounts of Pu(VI). The sorption efficiency toward Pu(VI) decreased with increasing biomass concentration due to increased agglomeration of the bacteria resulting in a decreased total surface area and number of available complexing groups. Spores of Bacillus sphaericus showed a higher biosorption than the vegetative cells at low biomass concentration which decreased significantly with increasing biomass concentration. At higher biomass concentrations (> 0.7 g/L), the vegetative cells of both strains and the spores of B. sphaericus showed comparable sorption efficiencies. Investigations on the pH dependency of the biosorption and extraction studies with 0.01 M EDTA solution have shown ...

Energy Technology Data Exchange (ETDEWEB)

The object and the purpose of the present work was to develop, to assemble and to start running a new TOF (time of flight) mass spectrometer for imaging SNMS analytic which is optimized for the analysis of highly molecular secondary ions. The most important purpose was the characterization of the TOF mass spectrometer. The obtained mass spectra of indium, tantalum and silver clusters reflect the excellent properties of the TOF mass spectrometer for the detection of large clusters with good detection efficiency up to masses of 16000 amu. The possibility of the deflection of selected saturated atom and cluster peaks serves for further improvement of the detection efficiency for large molecules. The accessible mass resolution was determined to be of the order of m/{delta}m=1000 in the high mass region. Numerous measurements were carried out to characterize the useful yield of this spectrometer. For a best possible adaptation of the TOF mass spectrometer for the ...

Science.gov (United States)

The purpose of this investigation was to determine the association between gender and the prevalence and incidence of patellofemoral pain syndrome (PFPS). One thousand five hundred and twenty-five participants from the United States Naval Academy (USNA) were followed for up to 2.5 years for the development of PFPS. Physicians and certified athletic trainers documented the cases of PFPS. PFPS was defined as retropatellar pain during at least two of the following activities: ascending/descending stairs, hopping/jogging, prolonged sitting, kneeling, and squatting, negative findings on examination of knee ligament, menisci, bursa, and synovial plica, and pain on palpation of either the patellar facets or femoral condyles. Poisson and logistic regressions were performed to determine the association between gender and the incidence and prevalence of PFPS, respectively. The incidence rate for PFPS was 22/1000 person-years. Females were 2.23 times (95% CI: 1.19, 4.20) more ...

Energy Technology Data Exchange (ETDEWEB)

A multi-faceted research program has been performed to investigate in detail several aspects of free and forced convective cooling of underground electric cable systems. There were two main areas of investigation. The first one reported in this volume dealt with the fluid dynamic and thermal aspects of various components of the cable system. In particular, friction factors for laminar flow in the cable pipes with various configurations were determined using a finite element technique; the temperature distributions and heat transfer in splices were examined using a combined analytical numerical technique; the pressure drop and heat transfer characteristics of cable pipes in the transitional and turbulent flow regime were determined experimentally in a model study; and full-scale model experimental work was carried out to determine the fluid dynamic and thermal characteristics of entrance and exit chambers for the cooling oil. The second major area of activity, ...

Energy Technology Data Exchange (ETDEWEB)

Magnetic coupling between two or more metal centers is an important facet of d- and f-block transition metal chemistry due to its implications in chemical bonding. With respect to actinide metals, magnetic coupling between polymetallic actinide centers is less well-known. Of the few documented examples, only one bimetallic uranium(V) complex, [(MeC{sub 5}H{sub 4}){sub 2}U]{sub 2}[{mu}-1,4-N{sub 2}C{sub 6}H{sub 4}] (1), has unequivocally demonstrated antiferromagnetic coupling. This complex employs a {pi}-conjugated 1,4-phenylenedimide ligand system which bridges the two f{sup 1}-metal centers and enables antiferromagentic coupling between unpaired f-e1ectrons residing in a {pi}-symmetry orbital. In this communication, we report the synthesis of a dimeric bis(imido) uranium(V) iodide complex and demonstrate with magnetic susceptibility measurements and density functional theory (DFT) calculations that the f{sup 1}-uranium centers display antiferromagnetic coupling ...

International Science & Technology Center (ISTC)

Highly Precision Method for Nondestructive Analysis of Surfaces in a Subnanometer Depth Range

International Nuclear Information System (INIS)

The present investigation was conducted at Ismaillia Research Station-Agricultural Research Center, Ismaillia Governorate, during the two successive seasons of 2000 and 2001. Two varieties of peanut (Arachis hypogaea L) namely Giza 4 and Giza 5 were treated with gamma ray doses; 10,15, 20, 25 Kr in order to induce genetic variability and to study the importance of the relative contribution of peanut yield components by employing some statistical procedures, i.e. simple correlation, multiple linear regression and stepwise regression analysis. The results showed that, there was significant positive correlation between seed yield/plant and no. of pods/plant, 100 seed weight, shelling percentage and pod yield/plant, and there was significant positive correlation between pod yield/plant and no of seed/plant,100 pod weight and 100 seed weight. The multiple linear regression analysis clearly showed that the ...

UK PubMed Central (United Kingdom)

BackgroundThe production of high yields of recombinant proteins is an enduring bottleneck in the post-genomic sciences that has yet to be addressed in a truly rational manner. Typically...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Three possibilities to observe the Higgs-top interaction at future {gamma}{gamma}-colliders are discussed: (a) associated Higss production via the {gamma}{gamma}{yields}tanti tH reaction, (b) Higgs obliged radiative correction to the {gamma}{gamma}{yields}tanti t channel, (c) Higgs resonance production via {gamma}{gamma}{yields}H{yields}ZZ. The results obtained show windows of the Higss mass where the Yukawa interaction of the Higss with the top quark can be studied at {gamma}{gamma}-colliders. (orig.).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

British Library Electronic Table of Contents (United Kingdom)

Correct prediction of the fission products inventory in irradiated nuclear fuels is essential for accurate estimation of fuel burnup, establishing proper requirements for spent fuel transportation and storage, materials accountability and nuclear forensics. Such prediction is impossible without accurate knowledge of neutron induced fission yields. The uncertainty of the fission yields reported in the ENDF/B-VII.0 library is not uniform across all of the data and much of the improvement is desired for certain fissioning isotopes and fission products. We discuss our measurements of cumulative fission yields in nuclear fuels irradiated in thermal and fast reactor spectra using Inductively Coupled Plasma Mass Spectrometry.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

... data deuteron beams energy dependence errors gamma radiation lead 203

UK PubMed Central (United Kingdom)

Grain yield is a major goal for the improvement of durum wheat, particularly in drought-prone areas. In this study, the genetic basis of grain yield (GY), heading date (HD), and plant height (PH) was...Full Text Available

International Nuclear Information System (INIS)

The current methods used by the tissue analysis program at LASL for the determination of americium and plutonium in autopsy tissue are described. Problems affecting radiochemical yield are discussed. Included are problems associated with sample preparation, separation of plutonium from large amounts of bone ash, and reagent contamination. The average "2"4"2Pu tracer yield for 1800 Pu determinations is 78 +- 12%. The average "2"4"2Am tracer yield is 85 +- 7% for 40 determinations.

Energy Technology Data Exchange (ETDEWEB)

Sputter-removal rates of overlayer and interfacial species on silicon are analyzed to determine sputtering yields for the species involved. Sputtering yields up to two orders of magnitude lower than those measured for silicon are found, and the results are interpreted in terms of a cascade mixing process which continually reburies much of the overlayer material beyond the escape depth of the sputtered atoms.

Energy Technology Data Exchange (ETDEWEB)

Field-grown snap bean plants were treated with simulated acidic rain applied either alone or in combination with ambient rain and the effects on growth and yield were determined. In plots where ambient rain was excluded, a retractable canopy was activated to shield the crop. Four levels of acidity at pH values of 5.0, 4.2, 3.4 and 2.6 were applied in four replicate treatments and the experiment was conducted in two successive years (1981 and 1982). In plots that received only simulated rain, yield was not adversely affected by acidic rain; in 1981, a positive linear relationship was present between acidity of simulated rain and yield, but in 1981, no effect was found. In contrast, in plots that received both simulated and ambient rain, a negative linear relationship between acidity in simulated rain and yield was observed in both years.

International Nuclear Information System (INIS)

This investigation was carried out during the two seasons of 1998/1999 and 1999/2000 at the experimental farm belonging to the plant research department, nuclear research center, atomic energy authority in Inshas to evaluate four lupin mutant lines (L_1, L_2, L_3 and L_4) along with their original mother varieties giza 1 and giza 2 under different levels and nitrogen fertilizer levels. The results indicated that seed yield/ plant and its effective components number and weight of pods/plant were significantly higher in all the mutant lines as compared to their parents either in the first or second seasons. Concerning the effect of irrigation intervals on yield and its components for developed mutants and their mother varieties as well as the results gave an evidence that the wider interval showed the lesser values for yield and most of yield components. Obtained data also revealed that ...

International Nuclear Information System (INIS)

Although some polymer conductors of electricity (ex. Polyanilines) are materials known for more than 100 years, only recently have the interesting chemical, electrical and optic properties of their insulating and conducting forms been recognized. Advances made in the chemistry of polymer conductors have also led to improvements in processing them. This work studies a practical application of these materials: the use of polymer conductors for the remote welding of insulating thermoplastic polymers, using energy from microwaves for the local heating of the union. Many thermoplastics (for ex. Polyethylene) do not absorb, or absorb very little, energy from microwaves. Different conductor materials (conductor polymers, carbon nanotubes), however, heavily absorb energy from microwaves with the resulting heating. In this way the welding zone can be heated without affecting the rest of the piece. Conductor polymers (polyanilines) were synthesized chemically and they were characterized by ...

Energy Technology Data Exchange (ETDEWEB)

Measurements were made of the cross sections for the /sup 27/Al(/sup 16/O,/sup 15/N)/sup 28/Si, /sup 89/Y(/sup 15/N,/sup 16/O)/sup 88/Sr and /sup 89/Y(/sup 27/Al,/sup 28/Si)/sup 88/Sr reactions at energies near and below the Coulomb barrier. The first reaction required separate measurements of the transfer to elastic cross section ratio for particular charge states, the charge state distribution for /sup 27/Al and /sup 28/Si ions, and the absolute elastic scattering cross section for the /sup 27/Al + /sup 16/O system. The ratio measurement required the combined use of two relatively new scientific instruments: the momentum filter and the Bragg curve spectrometer. The latter two transfer measurements were performed using the same setup involving surface barrier detectors at backward angles. Additional elastic scattering data for the /sup 15/N + /sup 28/Si, /sup 89/Y + /sup 15/N, /sup 89/Sr + /sup 27/Al, and /sup 88/Sr + /sup 28/Si systems was collected to provide ...

Energy Technology Data Exchange (ETDEWEB)

The oxide colloidal route, developed in the laboratory for mono-metallic catalysts, consists in preparing a metallic oxide hydro-sol which leads to the supported catalyst after deposition onto a support and an activation stage. In this work, this method has been adapted to the preparation of alumina supported bimetallic Pd-Sn catalysts to determine its interest for the control of the properties of the bimetallic phase (size, composition and structure). In the preliminary study concerning tin oxide sols, SnO{sub 2} (size=2,3 nm) and Sn{sub 6}O{sub 4}(OH){sub 4} (size = 25 nm) nano-particles were synthesized by neutralization respectively for tin(IV) and tin(H). The control through the pH of the aggregation of the PdO and SnO{sub 2} particles revealed that increasing oxide solubility promotes integral re-dispersion of the oxide particles. To synthesize oxide bimetallic sols, three strategies were defined. Copolymerization (formation of a mixed oxide nano-sol by cross condensation of both ...

Science.gov (United States)

The gas-phase reaction of benzene with O(3P) is of considerable interest for modeling of aromatic oxidation, and also because there exist fundamental questions concerning the prominence of intersystem crossing in the reaction. While its overall rate constant has been studied extensively, there are still significant uncertainties in the product distribution. The reaction proceeds mainly through the addition of the O atom to benzene, forming an initial triplet diradical adduct, which can either dissociate to form the phenoxy radical and H atom, or undergo intersystem crossing onto a singlet surface, followed by a multiplicity of internal isomerizations, leading to several possible reaction products. In this work, we examined the product branching ratios of the reaction between benzene and O(3P) over the temperature range of 300 to 1000 K and pressure range of 1 to 10 Torr. The reactions were initiated by pulsed-laser photolysis of NO2 in the presence of benzene and ...

International Nuclear Information System (INIS)

Full text: Measurement of K_#beta# to K_#alpha# x-ray intensity ratios are important not only in the field of atomic physics, radiation physics and medical physics, but also to test the validity of assumptions made in the theoretical prediction. The intensity ratios can also give information on the effect of physical and chemical environment of the element in the compound. Many investigators have adopted a single and double reflection geometries to measure the K_#beta# to K_#alpha# x ray intensity ratios to understand the effect of physical and chemical environment on x-ray fluorescence. The targets are excited by a radioactive source of having activity of the order 100 MBq. in order to carry out accurate measurement K_#beta# to K_#alpha# x-ray intensity ratios, we have develop 2#pi# geometrical configuration method : placing a target right on the surface of the detector facing the target to measure the K shell fluorescence parameters such as fluorescence ...

Science.gov (United States)

The x-ray diffraction technique described previously for measurement of growth kinetics of Pd/sub 2/Si layers from their solid state reaction couples has been extended by the use of a one-dimensional position-sensitive detector (PSD). Additionally, the method has been extended to include measurement of the Pd layer. A detailed description of the experimental arrangement and analytical procedures is presented. The kinetics of epitaxial Pd/sub 2/Si film growth were measured in situ over a range of 170--230 /sup 0/C. The PSD results, using data obtained from both the Pd/sub 2/Si and Pd layers, were able to confirm parabolic growth behavior for the Pd/sub 2/Si film. The rate constants followed Arrhenius behavior and yielded an activation energy of E = 1.32 +- 0.07 eV with a prefactor k/sub 0/ = 0.49 cm/sup 2//s for the Pd/sub 2/Si layer analysis and E = 1.34 +- 0.17 eV with a prefactor of 0.72 cm/sup 2//s for the Pd layer analysis. The PSD technique significantly ...

International Nuclear Information System (INIS)

Runit Island on Enewetak Atoll was very heavily impacted by the U.S. nuclear testing campaign in the northern Marshall Islands (1946-58). The primary source of contamination on Runit Island was the 1958 Quince safety test where a large quantity of device plutonium (Pu) was scattered over the area near the GZ. A second low-yield device was detonated on the same site 10 days later, further disturbing the soil and leaving behind a very heterogeneous pattern of contamination including milligram-size particles of plutonium. A limited cleanup of the Fig-Quince zone was carried out in 1979. During this period, the effectiveness of the cleanup operations was primarily evaluated on the basis of bulk soil concentration data with little consideration given to the heterogeneity and long-term material-, biological-, and environmental-specific impacts of residual high activity (hot) particle contamination. The aim of the present study was twofold; (i) to characterize the levels ...

International Nuclear Information System (INIS)

Soil erosion and small annual additions of organic matter from plant-sources are the major causes of low organic-matter content in our soils. The tops of the plants, fallen to the soil- surface, remain there are incorporated, the plant-roots, shrubs, grasses. And other native plants contribution much towards the soil organic matter. Populus spp. Are grown commonly around farmers' fields in the state of Azad Jammu and Kashmir. A pot-experiment was conducted to study the effect of addition of populus euramericana leaves on various physical and chemical characteristics of the soil. Soil was kept at field-capacity level and incubated at room temperature for 10 months after adding 25, 50, and 75 g of Populus curamericana leaves per pot. Changes in organic-matter content. PH, cation-exchange capacity extractable potassium, water-holding capacity, and bulk density were investigated, after incubation for 6,8,and 10 months. There was a linear increase in organic-matter ...

Energy Technology Data Exchange (ETDEWEB)

Work continued on the correlations of catalytic activity of metals and surface structure. Work is described in the following areas: CO oxidation on a Cu/Rh(100) Bimetallic catalysts; electronic properties of bimetallic surfaces; and reflection absorption spectroscopy of bimetallic surfaces. 5 figs. (CBS)

Wastenet

...Surface Aerators Products and Equipment Find and compare a variety of surface aerators products and equipment on the world's largest environmental industry portal. ...

Science.gov (United States)

Understanding climate development in the central Andes is important in determining the relationship between mountain range uplift and climate change. Recent work along the western margin of the central Andes has led to the development of two competing hypotheses: 1) that climate change is directly responsible for uplift or 2) that uplift controls climate change. In the first scenario, uplift results from increased friction at the plate boundary due to sediment-starvation of the trench which is a function of decreased run-off (particularly post 14 Ma) due to global cooling. In the second scenario progressive uplift of the Andean Cordillera during the Miocene resulted in a strong orographic effect with a concomitant rainshadow west of the Andes. To determine the relationship between climate change and uplift it is necessary to ascertain precisely, when the climate changed, the nature of that change and when uplift occurred. With respect to climate change a key question that has been ...

Science.gov (United States)

The e{sup +}e{sup -}{yields}pp cross section is determined over a range of pp masses, from threshold to 4.5 GeV/c{sup 2}, by studying the e{sup +}e{sup -}{yields}pp{gamma} process. The data set corresponds to an integrated luminosity of 232 fb{sup -1}, collected with the BABAR detector at the PEP-II storage ring, at an e{sup +}e{sup -} center-of-mass energy of 10.6 GeV. The mass dependence of the ratio of electric and magnetic form factors, G{sub E}/G{sub M}, is measured for pp masses below 3 GeV/c{sup 2}; its value is found to be significantly larger than 1 for masses up to 2.2 GeV/c{sup 2}. We also measure J/{psi}{yields}pp and {psi}(2S){yields}pp branching fractions and set an upper limit on Y(4260){yields}pp production and decay.

Energy Technology Data Exchange (ETDEWEB)

We investigate the sparticle production processes e{gamma} {yields} e tilde(Z tilde){sub 1} and {gamma}{gamma} {yields} (f tilde)(f tilde and bar) at high energy e{gamma} and {gamma}{gamma} colliders in the framework of the minimal supersymmetric standard model (MSSM). It will be shown that the e{gamma} colliders would be more suitable in searching for the heavy selectrons than ee colliders because of the low mass threshold of the process e{gamma} {yields} (e tilde)(Z tilde){sub 1}. We show that the standard background processes e{gamma} {yields} {nu}W and eZ can be suppressed in terms of initial beam polarization as well as the kinematical cuts on the energy and angle of the final electron. Moreover, it will be argued that the experimental measurements of the cross sections for the processes e{gamma} {yields} (e tilde)(Z tilde){sub 1} and {gamma}{gamma} ...

Science.gov (United States)

Maintenance energy expenditures were mesured for five rumen bacteria, Selenomonas ruminantium, Butyrivibrio fibrisolvens, Bacteroides ruminicola, Megasphaera elsdenii, and Streptococcus bovis, by using a complex medium with glucose as the carbon source. Large differences (as high as 8.5-fold) in maintenance energy expenditures were seen among these bacteria. The suggestion is made that maintenance requirements could be a significant determinant of bacterial competition in the rumen. Theoretical maximum growth yields, calculated from double reciprocal plots of yield versus dilution rate, were compared to theoretical Y(ATP) values in order to estimate minimum molar adenosine 5'-triphosphate yields from glucose for each bacterium. Results showed that relative yield among the bacteria was growth rate dependent. At high dilution rates, both S. ruminantium and S. bovis produced lactate as their principal ...

Energy Technology Data Exchange (ETDEWEB)

Restructured power markets require concepts not only for extending the lifetime of existing plants, but also concepts for reducing the life-cycle costs of existing older steam power plants in order to remain competitive with the most modern and advanced power generation technology such as combined cycle power plants. Out of the broad range of methods to extend service life and increase availability, and to increase power output and efficiency, this paper focuses on full repowering. Full repowering replaces the old fired boiler with gas turbine(s) and heat-recovery steam generators (HRSG) as heat input to the existing bottoming cycle and reuses the steam turbine (ST) condenser and further balance of plant (BOP) equipment. The potential offered by this concept is demonstrated. Repowering and modernization projects are executed if they result in economic benefits for the operator. Investment decisions need to be prepared based on an estimate or proof of an adequate return on investment ...

Energy Technology Data Exchange (ETDEWEB)

In order to obtain highly reliable InGaP/InGaAlP inner stripe (IS) lasers, the authors have clarified the relation between the maximum CW operation temperature and other laser characteristics, such as the pulsed threshold current, characteristic temperature, series resistance, and thermal resistance. The Al composition of the cladding layer, the carrier concentration of the p-cladding layer, and the thicknesses of the active layer and cladding layer have been optimized. It was found that an Al composition of 0.7 was the most suitable for the cladding layer, and the optimized carrier concentration was 4 x 10/sup 17/ cm/sup -3/. A maximum temperature of 90/sup 0/C was obtained for a 0.1 /mu/m active layer thickness and a 0.6 /mu/m cladding layer thickness. This is the highest value for InGaP/InGaAlP IS lasers, to our knowledge. In the case of a 0.06 /mu/m active layer thickness and a 0.8 /mu/m cladding layer thickness, a maximum temperature of 75/sup 0/C was obtained. IS lasers with ...

International Nuclear Information System (INIS)

Doubly-excited 2s-12p-13pnp autoionizing resonance series of Ne atom as well as autoionizing resonances in the 2s region of Na and Mg atoms have been studied with monochromatized synchrotron radiation. Use of charge-separated photoion-yield method allowed us to detect these weak resonances in a clarified way in the yield curves of doubly-charged ions. The observed resonance states have been interpreted with the help of MCDF calculations, and the decay processes of these resonance states are discussed briefly.

Energy Technology Data Exchange (ETDEWEB)

An improved method for the synthesis of (/sup 15/N) 16-Doxyl stearate, a fatty-acid spin label, is reported. The method requires only one mole of (/sup 15/N) 2-amino-2-methyl propanol per mole of methyl keto stearate with an overall yield of about 50%. In contrast, the previous method produced only 1-3% yield. The great improvement in yield was achieved mainly through the reduction of reaction volume which increases the reaction rate by the law of mass action.

International Nuclear Information System (INIS)

The paper presents experimental investigations of main features of plasma surface interaction and energy transfer to the material surface in dependence on plasma heat loads. The experiments were performed with QSPA repetitive plasma pulses of the duration of 0.25 ms and the energy density up to 2.5 MJ/m2. Surface morphology of the targets exposed to QSPA plasma screams is analyzed. Relative contribution of the Lorentz force and plasma pressure gradient to the resulting surface profile is discussed. development of cracking on the tungsten surface and swelling of the surface are found to be in strong dependence on initial temperature of the target.

British Library Electronic Table of Contents (United Kingdom)

Triacontanol (TRIA) has been realized as a potent plant growth promoting substance for a number of agricultural and horticultural crops. Out of a large number of essential oil bearing plants, mint (Mentha arvensis L.) constitutes the most important source of therapeutic agents used in the alternative systems of medicine. The mint plant has marvelous medicinal properties. In view of enhancing growth, yield and quality of this medicinally important plant, a pot experiment was conducted according to simple randomized block design. The experiment was aimed at studying the effect of four concentrations of TRIA (10?0, 10?7, 10?6 and 10?5?M) on the performance of mint with regard to growth and other physiological attributes, crop yield and quality attributes and the yield and contents of active c...

Energy Technology Data Exchange (ETDEWEB)

The nature of some baryonic resonances is still an unresolved issue. The case of the N{sup *}(1535) is particularly interesting in this respect due to the nearby {eta} N threshold and interference with the N{sup *}(1650). The N{sup *}(1535) has been described as a threshold effect, as a genuine 3-quark resonance, or as dynamically generated from the interaction of the octet of baryons with the octet of mesons. In the scheme of dynamical generation, predictions for the interaction of the N{sup *}(1535) with the photon can be made. In this study, we simultaneously analyze the role of the N{sup *}(1535) in the {pi}N{yields}{pi}N and {gamma}N{yields}{pi}N reactions and compare to the respective amplitudes from partial-wave analyses. This test is very sensitive to the meson-baryon components of the N{sup *}(1535). (orig.)

Energy Technology Data Exchange (ETDEWEB)

Iodine-125 labelled vinyl and aryl iodides are formed via the reaction of sodium iodide-125 with vinyl- and arylboronic acids. Good yields of isomerically pure products are obtained.

Energy Technology Data Exchange (ETDEWEB)

The reaction {gamma}d{yields}{pi}{sup +}nn is calculated up to order {chi}{sup 5/2} in chiral perturbation theory, where {chi} denotes the ratio of the pion to the nucleon mass. Special emphasis is put on the role of nucleon recoil corrections that are the source of contributions with fractional power in {chi}. Using the known near-threshold production amplitude for {gamma}p{yields}{pi}{sup +}n as the only input, the total cross-section for {gamma}d{yields}{pi}{sup +}nn is described very well. A conservative estimate suggests that the theoretical uncertainty for the transition operator amounts to 3% for the computed amplitude near threshold. (orig.)

International Nuclear Information System (INIS)

Neutron yield from the "6","7Li + d reaction has been investigated. The results obtained are compared with the published data with some theoretical models.

UK PubMed Central (United Kingdom)

Mangroves are disappearing rapidly worldwide despite their well documented biodiversity and the ecosystem services they provide. Failure to link ecological processes and their societal benefits has...Full Text Available

Science.gov (United States)

Pulse radiolysis studies of the formation kinetics and the yields of various phenylcarbenium ions from several different solutes in 1,2-dichloroethane solution have been carried out. The results indicate that there are two kinetically distinguishable cationic species of the solvent which react selectively with the different solutes to form the phenylcarbenium ions. It is suggested that one is a cation radical (yield 0.68 molecule/100 eV) and the other a carbocation (yield 0.20 molecule/100 eV). Rate constants for their separate reactions with selected aromatic compounds and with ammonia have been determined. Molar extinction coefficients have been estimated for benzyl cation, diphenyl cation radical, and anthracene cation radical. 6 figures, 1 table.

British Library Electronic Table of Contents (United Kingdom)

Good performance in extended lactations of dairy cattle may have a beneficial effect on food costs, health, and fertility. Because data for extended lactation performance is scarce, lactation persistency has been suggested as a suitable selection criterion. Persistency phenotypes were calculated in several ways: P1 was yield relative to an approximate peak, P2 was the slope after peak production, and P3 was a measure derived to be phenotypically uncorrelated to yield and calculated as a function of linear regressions on test-day deviations of days in milk. Phenotypes P1, P2, and P3 were calculated for sires as solutions estimated from a random regression model fitted to milk yield. Because total milk yield, calculated as the sum of daily sire solutions, was correlated to P1 and P2 (r=0.30 ...

British Library Electronic Table of Contents (United Kingdom)

Nitrogen use efficiency (NUE) of tef, a major staple crop in Ethiopia, is very low, either caused by untimely use of nitrogen (N) fertilizers or lack of other essential nutrients like sulphur (S). The average grain yield of this crop is low, averaging ?1 in farmer?s fields of the semi-arid conditions. Therefore, the present study was conducted to see the effect of the timing of combined N and S fertilization on the yield, yield components, and N and S concentration in the plant parts of the crop. A factorial combination of three rates of N (0, 70, and 105?kg?ha?1) with four rates of S (0, 16, 32, and 48?kg?ha?1) was applied in randomized complete blocks in three replications. The experiment was carried out in the 2004 and 2005 cropping seasons in the Cambisols of the semi-arid area of Ethi...

CERN Document Server

The measurements of the total delayed neutron yield from fast neutron induced fission of sup 2 sup 3 sup 8 U were made. The experimental method based on the periodic irradiation of the fissionable sample by neutrons from a suitable nuclear reaction had been employed. The preliminary results on the energy dependence of the total delayed neutron yield from fission of sup 2 sup 3 sup 8 U are obtained. According to the comparison of experimental data with our prediction based on correlation properties of delayed neutron characteristics, it is concluded that the value of the total delayed neutron yield near the threshold of (n,f) reaction is not a constant.

Science.gov (United States)

... data on pollen from red maple, birch, beech, ash, oak, hemlock and elm trees isolated from cores of ...

Energy Technology Data Exchange (ETDEWEB)

The mechanism of chemical poisoning of model heterogeneously catalyzed reactions on transition metal surfaces is studied. Clean Mo(001) surfaces were characterized; results suggest a first-layer contraction of 10% of the bulk interlayer spacing. Characterization of clean Co(0001) surfaces is underway. Decomposition of formic acid on Mo(001) surfaces is being studied. (DLC)

Energy Technology Data Exchange (ETDEWEB)

An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorption (TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative analysis by On-line mass ...

International Nuclear Information System (INIS)

Full text: Verification of the dose delivered to a patient during radiotherapy is an important quality assurance procedure, however this is rarely performed due to the extra time involved. Electronic portal images (EPIs) are currently acquired at many centres during radiotherapy treatment for positioning verification. These could be utilised for dose verification provided 1) an accurate prediction of the dose transmitted through the patient to the EPID can be produced for the patients' radiotherapy beams, and, 2) the EPID image can be converted to an accurate measured dose. Ideally, the radiotherapy planning system (RTPS) would be used to produce the predicted dose as part of the planning procedure. The aim of this project is to investigate whether the convolution-superposition model of the Pinnacle RTPS can accurately calculate dose transmitted through a patient and deposited in a phantom at a large source to surface distance. The dose transmitted through a ...

Science.gov (United States)

Using bremsstrahlung, the resonance fluorescence yield has been measured for the 1.836-MeV 2/sup +//sub 1/ level in /sup 88/Sr. The observed yield corresponds to a level width GAMMA = 2.94 +- 0.15 meV.

Energy Technology Data Exchange (ETDEWEB)

In the framework of the equivalence theorem the one-loop helicity amplitudes and cross section for the double Higgs production process {gamma}{gamma}{yields}HH are calculated. It is shown that the cross section is measurable at TeV {gamma}{gamma} colliders and is marginally sensitive to the triple-Higgs variation. (orig.).

International Nuclear Information System (INIS)

A review of fission product yields and delayed neutron data for Np-237, Pu-242, Am-242m, Am-243, Cm-243 and Cm-245 has been undertaken. Gaps in understanding and inconsistencies in existing data were identified and priority areas for further experimental, theoretical and evaluation investigation detailed. (author)

Energy Technology Data Exchange (ETDEWEB)

The production of three vector bosons in {gamma} {gamma} collisions studying the reactions {gamma} + {gamma} {yields} W{sup +} + W{sup -} + Z{sup 0} and {gamma} + {gamma} {yields} W{sup +} + W{sup -} + {gamma}. 12 refs., 4 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

Results of tests on the 1 kg/h continuous reactor for the hydroliquefaction of coal are described. The reactor was operated at 415-435 C and 21 MPa using a continuous stirred reactor with a retention time of about 2 hours. All product oils were recovered by distillation. Sub-bituminous coal was found to give the best product yield. Tests using 5% red mud and 3% improved red mud showed significant increases in oil yield. (4 refs.)

International Nuclear Information System (INIS)

A large IMF- and event characterizing multidetector system (CHICSI) is under development for storage ring experiments. In ''test'' experiments with telescopes of CHICSI type the IMF production has been measured for "1"4N induced reactions at 14A and 32A MeV. Detailed information about the emission sources, particularly from the IMF yield in reactions with isotope separated targets and from isobaric yield ratios in the sub-Coulomb region is discussed. (orig.).

International Nuclear Information System (INIS)

Planar channeling effects are studied in such well-oriented polycrystalline layers as NiSi_2 and Pb_2Si layers formed on single crystalline Si. Crystalline perfection of such layers is discussed by using the energy- and angular dependences of the axial and planar channeling yields. It has been shown that, in suitable conditions, the energy dependence of the planar yield is more sensitive to the spread of crystallite orientations in polycrystals than that of the axial one. (Auth.).

Science.gov (United States)

A compact heat exchanger pedestal array for augmenting heat transfer in a machine is disclosed. The compact heat exchanger pedestal array includes a wall having first and second surfaces. The first surface faces a heated flow path and the second surface p...

Energy Technology Data Exchange (ETDEWEB)

In the present work, we describe application of binary pseudo-random gratings (BPRG) and arrays (BPRA) as effective 1D and 2D test surfaces suitable for calibration of different surface profilometers, including a number of interferometric microscopes and scatterometers.

Energy Technology Data Exchange (ETDEWEB)

We examined, using thermo analytical methods, the effects of 2000 deg. C heat-treated graphite powders and heating rate of cure after impregnation on the thermal stability and carbon yield of furfuryl alcohol, which is frequently used not only as an impregnation but also as a matrix precursor for carbon fiber-reinforced carbon composites. It was founded that the addition of 30 wt%. graphite powders of furfuryl alcohol and the heating rate 35 deg. C/min showed the highest thermal stability of furfuryl alcohol/graphite powder mixture. The carbon yield above 1000 deg. C was enhanced more than 10% in comparison with the absence of graphite powders. It would be expected that this result can contribute to some extent to reduce the repeating number of processing cycle (carbonization {yields} impregnation {yields} cure {yields} re-carbonization) required to density a carbonaceous composite. ...

Energy Technology Data Exchange (ETDEWEB)

For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogen transfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic ...

Energy Technology Data Exchange (ETDEWEB)

We examine the virtual effects of Kaluza-Klein (KK) states on Higgs physics in universal extra dimension models. We study the partial widths {Lambda}{sub h{yields}gg}, {Lambda}{sub h{yields}{gamma}{gamma}}, and {Lambda}{sub h{yields}{gamma}Z}, which are relevant for Higgs production and detection in future collider experiments. These interactions occur at one loop in the Standard Model, as do the KK contributions. We find that the deviations induced by the KK exchanges can be significant; for one extra dimension, the gg {yields} h production rate is increased by 10% - 85% for the mass of the first KK state in the range 500 {approx}> m{sub 1} {approx}> 1500 GeV, a region untested by current direct search and precision measurement constraints. The h {yields} {gamma}{gamma} decay width is decreased by {approx}< 20% in the same mass range. For two or more universal ...

Energy Technology Data Exchange (ETDEWEB)

The relationship between coal properties and liquefaction or gasification characteristics was analyzed by using the analysis and test results and liquefaction characteristics in the coal data base. On liquefaction reaction, the close relation between an oil yield and coal constituent composition or a coal rank is well-known. Various multivariable regression analyses were conducted by using 6 factors as variables such as calorific value, volatile component, O/C and H/C atomic ratios, exinite+vitrinite content and vitrinite reflectance, and liquefaction characteristics as variate. On liquefaction characteristics, the oil yield of dehydrated and deashed coals, asphaltene yield, hydrogen consumption, produced water and gas quantities, and oil+asphaltene yield were predicted. The theoretical gasification efficiency of each specimen was calculated to evaluate the liquefaction reaction obtained. As a result, ...

Energy Technology Data Exchange (ETDEWEB)

The variation of surface composition and sintering of the binary Pd{sub 7}Ag{sub 3} nanoparticles prepared by chemical reduction were studied. The composition of the as-prepared Pd{sub 7}Ag{sub 3} nanoparticles across the diameter is inhomogeneous due to different reduction potentials of Pd and Ag. Upon heating, Ag will migrate to the surface because of its lower surface energy. Surface modification results in variation of surface composition during the sintering process. Stearic acid acts as a grain growth inhibitor. The migration of Ag to the surface is suppressed and the sintering is retarded. Modification by polyethylene glycol leads to more migration of Ag atoms from the core to the surface. This makes the nanoparticles easier to sinter.

Energy Technology Data Exchange (ETDEWEB)

This report details the laser surface mapping activity as described in technical tasks and QA plan 22751-TTQAP-LM.

International Nuclear Information System (INIS)

Cooling water is sprayed on the outer surface of an upper portion of a container, and a pool is formed by the cooling water flowing down while cooling the container. Further, the cooling water stored in the cooling water pool is recycled by a pump for spraying the cooling water on the outer surface of the upper portion of the container. Sufficient amount of cooling water is supplied for spraying the cooling water to the outer surface of the upper portion of the container so that the outer surface of the container is free from drying and a liquid membrane is formed on the entire surface. The amount of the cooling water is made greater than that of the cooling water evaporated when the entire amount of the heat generate in the reactor core of the reactor is transferred to the cooling water. Since the liquid membrane is formed on the entire surface of the container ...

Energy Technology Data Exchange (ETDEWEB)

This report describes the accomplishments of the University of Georgia in establishing an academic program geared toward the emerging biobased products industry. By virtue of its strengths and structure, the University of Georgia is particularly well-suited for developing a program focused on plant- and microbial-based bioproducts, and it was in this general area that this program was developed. The program had several unique characteristics. First, we implemented a distinguished lecture series that brought outstanding scientists and engineers to our University to interact with students and share their vision of the biobased economy. Second, we offered industrially-oriented and multidisciplinary courses that provided students with a broad background on various facets of biobased business and technology. Third, we provided the students with opportunities to expand beyond the classroom by engaging in research lab rotations and industrial internships. Fourth, each ...

Energy Technology Data Exchange (ETDEWEB)

We report on a recent search for {bar {nu}}{sub e} appearance from stopped {pi}{sup +} {yields} {mu}{sup +}{nu}{sub {mu}} and {mu}{sup +} {yields} e{sup +}{nu}{sub e}{bar {nu}}{sub {mu}} decay made by the LAMPF experiment E645. The appearance of {bar {nu}}{sub e} may occur from {bar {nu}}{sub {mu}} {yields} {bar {nu}}{sub e}, {nu}{sub e} {yields} {bar {nu}}{sub eL}, or {nu}{sub {mu}} {yields} {bar {nu}}{sub eL} oscillations. Appearance may also occur from rare {mu}{sup +} {yields} e{sup +}{bar {nu}}{sub e}{nu}{sub {mu}} decay, which is allowed by a multiplicative lepton charge conservation law. The neutrino energies range from E{sub {nu}} = 0 to 52.8MeV. The neutrino detector, which is located 26.1 meters from the neutrino source, consists of a segmented liquid scintillator and proportional drift tube central detector surrounded by both active and passive ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Short communication.

Science.gov (United States)

... Other Sources Toxics Intranet Subsurface Injection of Liquid Waste -- Florida Surface features of a typical...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

This patent describes a {gamma}-ray detector. It comprises: a dislocation-free single crystal having an input surface and a transmission surface at opposite ends thereof; an active shield surrounding the crystal and functioning as an anticoincidence counter; and {gamma}-ray detector means disposed adjacent the transmission surface of the crystal for receiving and detecting {gamma}-rays of a predetermined wavelength incident on the input surface of the crystal at a specific Bragg angle and transmitted through the crystal.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report measured the rate of isothermal deposition of sub-micron particles of magnetite onto the surface of Alloy 800 at pH of 4.2-9.3 at Re=10,000 and a fluid temperature of 25C. Deposition is modelled as a two-step process, the transport of particles to the surface region followed by attachment to the surface.

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

... Union (INTAS), Brussels (Belgium) Science and Technology Center in Unkraine,

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Defect cluster formation in 14-MeV neutron irradiated polycrystalline copper has been observed by transmission electron microscopy (TEM) and correlated with the increase in yield stress. The measurements indicate that the radiation hardening component of the yield strength in polycrystals is not directly additive to the unirradiated yield strength. A transitional behavior was observed for radiation hardening at low fluences, which produces an anomalous variation of the defect cluster barrier strength with fluence. The behavior is attributed to the effect of grain boundaries on slip band transmission. An upper limit for the room temperature barrier strength of defect clusters in neutron-irradiated copper was determined to be #alpha#=0.23. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The effect of asymmetric laser pulses on electron yield from a laser wakefield accelerator has been experimentally studied using > 10{sup 19} cm{sup -3} plasmas and a 10 TW, > 45 fs, Ti:Al{sub 2}O{sub 3} laser. Laser pulse shape was controlled through non-linear chirp with a grating pair compressor. Pulses (76 fs FWHM) with a steep rise and positive chirp were found to significantly enhance the electron yield compared to pulses with a gentle rise and negative chirp. Theory and simulation show that fast rising pulses can generate larger amplitude wakes that seed the growth of the self-modulation instability and that frequency chirp is of minimal importance for the experimental parameters.

British Library Electronic Table of Contents (United Kingdom)

Analysis of the pattern of the chromosomal localization of quantitative trait loci (QTLs) is necessary for comprehensively understanding their functions. The chromosomal localization of QTLs controlling milk production traits has been studied in cattle chromosomes. The distribution of QTLs between chromosomes has proved to be binomial. Their distribution along each chromosome was, in general, uniform, except for the QTLs controlling the somatic cell score (SCS), which tended towards telomeric location. However, there are chromosomes either enriched with or particularly poor in QTLs. The QTL distribution patters are the most similar for the milk yield (M) and milk protein yield (P) and for milk fat yield (F) and milk fat content (%F). The pattern of the SCS QTLs stands out among those of ot...

British Library Electronic Table of Contents (United Kingdom)

Comparative patterns of equilibrium adsorption of argon on the surface of graphitized thermal carbon black (GCB) and the inhomogeneous surfaces of nongraphitized carbon black and silica at 77 and 87.3 K were considered. It was shown that argon acquires the properties of a special phase with a layered structure and exhibits two-dimensional phase transitions with the formation of crystal-like layers near the homogeneous surface of GCB even at a temperature exceeding the triple point. However, already at a distance of three-four molecular diameters from the surface, adsorbed argon behaves as a bulk phase in a weak external field. The defect surface of nongraphitized carbon black and the amorphous surface structure of silica destroy the longrange order of adsorbed argon and lower its solidific...

Science.gov (United States)

This invention is an improved solar energy cavity receiver for exposing materials and components to high temperatures. The receiver includes a housing having an internal reflective surface defining a cavity and having an inlet for admitting solar radiation thereto. A photothermal absorber is positioned in the cavity to receive radiation from the inlet. A reflective baffle is positioned between the absorber and the inlet to severely restrict the re-radiation of energy through the inlet. The front surface of the baffle defines a narrow annulus with the internal reflective surface of the housing. The front surface of the baffle is contoured to reflect incoming radiation onto the internal surface of the housing, from which it is reflected through the annulus and onto the front surface of the absorber. The back surface of the baffle intercepts ...

Energy Technology Data Exchange (ETDEWEB)

This invention is an improved solar energy cavity receiver for exposing materials and components to high temperatures. The receiver includes a housing having an internal reflective surface defining a cavity and having an inlet for admitting solar radiation thereto. A photothermal absorber is positiond in the cavity to receive radiation from the inlet. A reflective baffle is positioned between the absorber and the inlet to severely restrict the re-radiation of energy through the inlet. The front surface of the baffle defines a narrow annulus with the internal reflective surface of the housing. The front surface of the baffle is contoured to reflect incoming radiation onto the internal surface of the housing, from which it is reflected through the annulus and onto the front surface of the absorber. The back surface of the baffle intercepts ...

Energy Technology Data Exchange (ETDEWEB)

The sedimentary geometry is determined by several types of stratigraphic surfaces: transgressive surfaces (TS), maximum flooding surfaces (MFS) and downward shift surfaces (DS). They are organized hierarchically into major and minor surfaces from the facies stacking-pattern. These surfaces which are observable on well logs and cores structure the sedimentary architecture and are, therefore, the best candidates to form major seismic reflectors. The well (logs and cores) to seismic (surface seismic) passage involves inherently a change of observation scale. That is from a high resolution sequence stratigraphy (metric to pluri-metric) to a sequence stratigraphy s.l. (decametric to pluri-decametric). This passage is composed of two phases. The first phase consists of the validation of density and sonic logs whose product corresponds to the ...

Energy Technology Data Exchange (ETDEWEB)

Excimer laser processing enables both thermally-driven transformations and the incorporation of solutes into the surface of materials through melting and diffusional mixing. We have examined the effect of excimer laser processing on the microstructure and surface mechanical properties of titanium alloys. Changes in the surface hardness due to laser processing were studied using a Nanoindenter [trademark]. Alloying experiments using both mixing of evaporated surface layers of boron and laser gas alloying in air and in nitrogen all result in changes in the surface hardness of the material. Alloying with boron results in an amorphous surface which is somewhat harder than the as polished surface. Laser processing in air and pure nitrogen results in incorporation of oxygen and nitrogen and the development of fine ([approximately] 50 nm) ...

British Library Electronic Table of Contents (United Kingdom)

There is investigated the role of polymer layers on the metal surface of a fine filler in the formation of a PVC system with electrophysical properties. It is shown that a physicochemical polymer modification takes place under the surface active center influence. Thus, the surface layer properties (density and geometrical characteristics) differ from the PVC ones. The correlation between the electrophysical properties of the PVC composite and the surface layer in the range of the fine copper fraction of 0?11.3 vol % at E ? 106 V m?1 and a frequency response of 20?2 ? 105 Hz is determined. An explanation of the investigated relation is presented.