Energy Technology Data Exchange (ETDEWEB)

Decreasing the aperture of a solar central receiver operating at high temperatures contributes significantly to the increase of the efficiency of energy absorption. However, decreasing the aperture also decreases the collection efficiency. A simple solution is using a 3D-CPC as secondary element for augmenting the energy collection, while the aperture can remain relatively small. Nevertheless, the receiver aperture as well as the secondary concentrator are usually rather large. For practical considerations an approximate solution may be chosen at times, designing the concentrator by a series of truncated cones. However, in particular cases, the solution of truncated cones remains expensive and unpractical and therefore the authors designed a CPC approximated by a series of trapezoidal planar facets. Under technical restrictions, there is an optimum for choosing the partition of the pure-CPC in truncated pyramids and the paper presents the ...

Energy Technology Data Exchange (ETDEWEB)

This handbook covers the general area of lubrication and tribology in all its facets: friction, wear lubricants (liquid, solid, and gas), greases, lubrication principles, applications to various mechanisms, design principles of devices incorporating lubrication, maintenance, lubrication scheduling, and standardized tests; as well as environmental problems and conservation. The information contained in these two volumes will aid in achieving effective lubrication for control of friction and wear, and is another step to improve understanding of the complex factors involved in tribology. Both metric and English units are provided throughout both volumes.

International Nuclear Information System (INIS)

In this paper, numerical simulation of a concentric tube heat exchanger is presented to determine the convective heat transfer coefficient and friction factor in a smooth tube. Increasing the convective heat transfer coefficient can increase heat transfer rate in a concentric tube heat exchanger from a given tubular surface area. This can be achieved by using heat transfer augmentation devices. This work constitutes the initial phase of the numerical simulation of heat transfer from tubes employing augmentation devices, such as twisted tapes, wire-coil inserts, for heat transfer enhancement. A computational fluid dynamics (CFD) simulation tool was developed with CFX software and the results obtained from the simulations are validated with the empirical correlations for a smooth tube heat exchanger. The difficulties associated with the simulation of a heat exchanger augmented with ...

International Nuclear Information System (INIS)

The use of heat transfer augmentation devices has been proposed as a means for reducing the cost of steam generators for advanced LMR designs by approximately 25%. Experimental results are presented for two types of enhancers in the form of a twisted-tape and a core-tube insert in the steam tube of a 13.1-m-long, sodium-heated single-tube test section. Test parameters were prototypical of liquid metal reactor (LMR) steam generator design for a once-through high-pressure steam cycle. Heat transfer results are compared with the no-insert case on an overall and local basis. Although both augmentations increased overall performance, the mechanisms were different.

International Nuclear Information System (INIS)

The world fusion program has advanced to the stage where it is appropriate to construct a number of devices for the purpose of burning DT fuel. In these next-generation experiments, the expected flux and fluence of 14 MeV neutrons and associated gamma rays will pose a significant challenge to the operation and diagnostics of the fusion device. Radiation effects include structural damage to materials such as vacuum windows and seals, modifications to electrical properties such as electrical conductivity and dielectric strength and impaired optical properties such as reduced transparency and luminescence of windows and fiber optics during irradiation. In preparation for construction and operation of these new facilities, the fusion diagnostics community needs to work with materials scientists to develop a better understanding of radiation effects, and to undertake a testing program aimed at developing workable solutions for this ...

International Nuclear Information System (INIS)

III--V based devices such as field effect transistors, heterojunction bipolar transistors, and lasers often have surface leakage and thermal degradation problems due to surface states which pin the Fermi level to the midgap. Sulfur based passivation processes are known to improve device performance by altering surface-state densities. We have developed a voltage-controlled anodic sulfur passivation scheme using Na_2S dissolved in ethylene glycol. Our process has repeatedly produced a #approx#25% improvement in peak output power near the catastrophic damage limit in visible (#lambda#=670 nm) AlGaInP edge-emitting lasers. The threshold current density before and after passivation, and the I--V characteristics before and after catastrophic failure, were essentially unchanged indicating that passivation raises the threshold for facet damage.

British Library Electronic Table of Contents (United Kingdom)

This study reports a determination of the polarity of WC facets in WC-Co alloys sintered at the liquid state. In these alloys, WC grains are delimited by basal facets and two sets of {101 0} prismatic facets, one set of facets being much more developed than the other. A variation of the shape is observed as a function of the composition of the alloy. High resolution transmission electron microscopy is used to investigate the polarity of the prismatic facets owing to the typical triangular patterns appearing on the images. The effect of the composition is investigated using two alloys with different carbon potentials and one containing VC and Cr3C2 as grain growth inhibitors. The interpretation of the images shows that in all cases, the same set of prismatic planes is favoured.

UK PubMed Central (United Kingdom)

AIM: To evaluate the effects of percutaneous ozone injection via the posterior-lateral route and inner margin of the facet joint in the treatment of large lumbar disc herniation.METHODS:...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Individuals who use augmentative and alternative communication (AAC) depend on technology to meet their daily needs and form relationships. Speech generating devices (SGDs) are integral components of communication systems. Reliability of SGDs is critical for effective use in everyday life. This study examined the reliability of new SGDs and found that mean time to first failure was 42.7 (SD = 41.2) weeks and at least 40% required repairs within the first year of use. The components that most frequently broke down were touch screens, wiring, main boards, batteries, memory cards, and AC adaptors. The costs of repairing SGDs were analyzed. The clinical implications of device breakdown are identified for key stakeholders, including clients, families, service providers, funding agencies, and ma...

Energy Technology Data Exchange (ETDEWEB)

Substantial thermal performance improvement in ice-on-tube cold thermal energy storage systems (TES) is possible by making use of porous copper mesh as a Heat Conducting Enhancement Device (HCED). HCEDs are inexpensive heat transfer augmentation devices that can result in faster rate of ice growth and larger final steady state ice build volume by reducing the controlling thermal conduction resistance of the ice layer. This improves the competitiveness of external ice-on-tube systems as compared to other TES systems, such as dynamic ice harvesters and static internal melt systems. In this study the amount of ice growth enhancement is predicted theoretically, by performing simplified 1-D calculations, and is then validated in the laboratory through carefully controlled experiments. This study shows that ice volume increase between 50 and 90% is possible by using HCEDs of the type tested. (author)

Energy Technology Data Exchange (ETDEWEB)

A comprehensive presentation is made of state-of-the-art configurations and design methodologies for heat transfer devices applicable to industrial processes, automotive systems, air conditioning/refrigeration, cryogenics, and petrochemicals refining. Attention is given to topics in heat exchanger mechanical design, single-phase convection processes, thermal design, two-phase exchanger thermal design, heat-transfer augmentation, and rheological effects. Computerized analysis and design methodologies are presented for the range of heat transfer systems, as well as advanced methods for optimization and performance projection.

Energy Technology Data Exchange (ETDEWEB)

The concentric circular annular duct is a common geometry in many fluid flow and heat transfer devices. For the purpose of heat transfer augmentation, fins are often employed in the annular region, and such finned ducts find wide application in compact heat exchangers (5, 6). The analysis of flow and heat transfer in this geometry is, therefore, quite important from an engineering standpoint. For fully developed conditions, the problem has already been analyzed (7-10). However, no results are available for the developing flow in the entrance region. It is with this latter problem that the present paper is concerned.

Science.gov (United States)

... JTIDS) LPC-10 voice channel has been an important facet of a larger ongoing in-house research task on Digital Audio Technology for Aircraft ...

International Nuclear Information System (INIS)

The augmentation of the heat transfer by inserting different type turbulators into the channels is the conventional passive enhancement method. The coiled wire is one of the common heat transfer enhancement devices. These turbulators generate almost-periodic vortices into the flow while increasing the heat transfer rate. In this study, the properties of these vortices (i.e. the vortex shedding frequency and amplitudes of the pressure fluctuations of the vortices), flow (vortex)-acoustic coupling and the relation between entropy generation and vortex characteristics were investigated experimentally. Strouhal-Re-N_s_,_a and P_r_m_s-Re-N_s_,_a variations were presented graphically. It was observed that as the pitch increases, the vortex shedding frequencies decrease and the maximum amplitudes of pressure fluctuation of vortices produced by coiled wire turbulators occur with small pitches. In addition, the effects of the turbulators on the heat ...

Science.gov (United States)

Not Available

Science.gov (United States)

Page 1. Overview of the DARPA Augmented Cognition Technical Integration Experiment Mark St. John, David A. Kobus ...

Energy Technology Data Exchange (ETDEWEB)

In this paper the concept of a composite power system stabilizer is investigated. This stabilizer comprises a properly designed, robust, conventional power system stabilizer (CPSS) and an auxiliary stabilizer (AS) which can be either a self-tuning stabilizer (ASTS) or a fixed-parameter stabilizer (AFPS). For small disturbances, the CPSS performs satisfactorily over a wide range of operating conditions. When large disturbances occur the auxiliary stabilizer augments the performance of the CPSS. It has been demonstrated that the composite power system stabilizer can significantly improve the dynamic performance of the system when there is a major disturbance such as a short circuit in the system. Because in the case of a single-machine system the parameters of the ASTS do not vary appreciably, it can also be implemented as a fixed-parameter device; this simplifies significantly the implementation of the composite PSS. (Author)

UK PubMed Central (United Kingdom)

A patient is presented with a cervical spinal cord transection which occurred after a motor vehicle accident in which the air bag deployed and the seat belt was not in use. The patient had complete...Full Text Available

UK PubMed Central (United Kingdom)

Social stress is prevalent in many facets of modern society. Epidemiological data suggest that stress is linked to the development of overweight, obesity and metabolic disease. Although there...Full Text Available

Science.gov (United States)

... turbine blade heat-transfer and study the heat-transfer augmentation in idealized geometry and its ... responsible for heat transfer augmentation. ...

Science.gov (United States)

Fundamental study of heat transfer augmentation of tube inside surface by cascade smooth surface-turbulence promoters

Science.gov (United States)

... roughness. Since T u'v' and q v'"F the heat transfer augmentation is the square root of the skin friction augmentation: - 1/2 (( St - ,Cf 0 ...

Science.gov (United States)

Shape optimization of heat transfer augmentation device employed in turbine blade internal cooling passage has been performed numerically using single as well as multi-objective optimization procedures. Polynomial response surface approximation method and multi-objective genetic algorithm are used for single and multi-objective optimizations, respectively. Problem to enhance heat transfer rate considering staggered dimples on single surface of cooling passage has been formulated, and Reynolds-averaged Navier-Stokes equations are solved to analyze the flow field and the heat transfer. Three design variables defining channel and dimple dimensions, and two objective functions related to Nusselt number and friction drag are employed. Latin hypercube sampling is used to generate sampling points in design space, and the evaluated objectives are used to generate a set of optimal designs. Optimal shapes show higher heat transfer rates in the case of ...

Science.gov (United States)

Not Available

Science.gov (United States)

Not Available

Science.gov (United States)

Not Available

British Library Electronic Table of Contents (United Kingdom)

A new series of anatase TiO2 hollow structures were prepared by a facile hydrothermal process. When the hydrothermal time was increased from 20min to 72h, the resulting TiO2 solid spheres gradually transformed into TiO2 hollow spheres with higher surface crystallinity and exposed {001} facets. The as-prepared TiO2-72h sample exhibited the highest activity comparing to other TiO2-based samples and commercial product Degussa P-25 towards the selective photocatalytic oxidation of toluene to benzaldehyde. Such great photocatalytic performance was mainly attributed to enhanced UV-adsorption and better charge separation efficiency due to higher surface crystallinity of TiO2-72h.

British Library Electronic Table of Contents (United Kingdom)

We report a solution-phase synthetic route to copper nanoparticles with controllable size and shape. The synthesis of the nanoparticles is achieved by the reduction of copper(II) salt in aqueous solution with hydrazine under air atmosphere in the presence of poly(acrylic acid) (PAA) as capping agent. The results suggest that the pH plays a key role for the formation of pure copper nanoparticles, whereas the concentration of PAA is important for controlling the size and geometric shape of the nanoparticles. The average size of the copper nanoparticles can be varied from 30 to 80 nm, depending on the concentration of PAA. With a moderate amount of PAA, faceted crystalline copper nanoparticles are obtained. The as-synthesized copper nanoparticles appear red in color and are stable for weeks, ...

J-STORE (Japan)

Full Text Available

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The effect of WC particle size with the addition of VC as a grain growth inhibitor was investigated during the liquid phase sintering of WC-Co system. With increasing WC particle size at the same VC content, the effect of grain growth inhibition was increased. Also, with increasing the VC content, the grain shape of WC was changed from the faceted shape to the distorted shape, and the step density of the WC grain was increased. (orig.)

CERN Document Server

Simulation approaches for nano-scale semiconductor devices

Science.gov (United States)

Experimental results are presented for a new and unique heat transfer augmentation technique in tubes. The technique consists of inserting a porous mesh structure into the flow passage of the tube. Due to the increased degree of turbulence, both the singl...

Science.gov (United States)

Scraped-surface heat transfer augmentation is proposed as a possible technique for use in improved air-cooling designs. Although it has been in common use with liquids, the technique has apparently never been used with gases. An experimental investigation...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to identify the radiative heat transfer augmentation by a coaxial cylinder introduced in the infinite cylindrical pipe enclosing a participating gas. The gas is either a mixture of water vapor and carbon dioxide or gray. The gas is assumed to be homogeneous at a constant temperature, and has a refractive index of unity. All of the surfaces are opaque and gray, diffusely emitting and reflecting at a constant temperature. The effect of system diameter, diameter ratio, wall emittances, gas and surface temperatures, mixture component on heat transfer augmentation are studied by using the zone method with participating gas radiative properties evaluated from the weighted sum of gray gases model. From the radiative equilibrium condition, the installed wall temperature is formulated and calculated by the iteration method. If the medium is a gray gas, the augmentation observed are negligible. For the ...

Science.gov (United States)

The Real Time Specification for Java (RTSJ) is an augmentation of Java for real time applications of

International Nuclear Information System (INIS)

Heat transfer augmentation has developed into a major specialty area in heat transfer research and development. A bibliography of world literature on augmentation is presented. The literature is classified into passive augmentation techniques, which require no external power, and active techniques, which do require external power. The fourteen techniques are grouped in terms of their application to the various modes of heat transfer. Mass transfer is included for completeness. Key words are included with each citation for technique/mode identification. The total number of publications cited is 1,967, including 75 surveys of various techniques and 42 papers on performance evaluation of passive techniques. Patents are not included as they will be the subject of a future topical report.

Science.gov (United States)

... solid particle contamination. Solid particulate impact is a good mechanism for surface heat transfer augmentation. The aug ...

Energy Technology Data Exchange (ETDEWEB)

Granted patents are an important source of information on the potential commercialization of augmented heat transfer technology. This report presents a bibliography of US patents pertinent to that technology. The total number of patents cited is 321. They are presented in three separate lists: by patent number, alphabetically by first inventor, and by augmentation techniques (with secondary arrangement according to mode of heat transfer).

International Nuclear Information System (INIS)

Molecular beam epitaxy (MBE) grown Ge nanodots are found to come in a clear trimodal island distribution of huts, pyramids, and domes when grown on (001)Si at 550 deg. C. The island types appear in this order as Ge coverage increases and for a certain coverage all three types are found to coexist at this growth temperature. Previously Ge nanodots have mostly been divided into huts and domes at growth temperatures below 600 deg. C, or pyramids and domes above 600 deg. C. The (105) faceted pyramidal and elongated huts and the multifaceted domes are well known, but a distinction has not previously been seen between huts and a separate size distribution of similarly (105)-faceted pyramidal nanodots twice the size of huts, at temperatures below 600 deg. C. The 20-25 nm wide huts also appear to be the smallest obtainable self-assembled Ge dots on (001)Si, in accordance with predictions based on Si_1_-_xGe_x nanodots on (001)Si. They are about a ...

Energy Technology Data Exchange (ETDEWEB)

Transmission electron microscopy studies on solution-annealed Alloy 800 revealed small (100-200 nm), spherical-shaped titanium carbide (face centered cubic structure) and large (200 nm-5 {mu}m), faceted titanium nitride (hexagonal structure) particles randomly distributed in the austenite matrix. The volume fraction of former particles was found to be greater than that of the latter. Corrosion studies of the alloy in acidic, chlorides and acidic chloride environments at room temperature indicated that the passivity of Alloy 800 was adversely affected by the addition Cl{sup -} ions. X-ray photoelectron spectroscopy revealed that the surface film formed on the alloy at the onset of passivity consisted of Cr{sup 3+} (as Cr{sub 2}O{sub 3}), without any Fe{sup 3+}/Fe{sup 2+} or Ni{sup 2+}. Scanning electron microscopy studies indicated initiation of pitting at large, faceted particles, not at small, spherical-shaped ones.

International Nuclear Information System (INIS)

In the present paper it is assumed that above a limiting value of fission fluency (burn-up) a more intensive process of irradiation introduced chemical interaction occurs. A significant part of fission gas product is thus expected to be chemically bounded in the matrix of UO_2 fuel. The fission gas atoms substituting, for example, uranium atoms in the crystallographic lattice can form weak facets. At a certain saturation condition, division of the grains can occur at the weak facets and the increase in fission-gas products release may be expected. The fact that the process of grain division for high burn-ups (70-80 MWd/kgU) forms an extremely fine structure up to the temperature as high as 1100 "oC and simultaneously the observed decreases in fission gas concentration in the fuel supports this concept. The analysis of fission gas concentration change due to the formation of nanostructures in UO_2 fuel at high burn-ups in terms of total surface ...

Energy Technology Data Exchange (ETDEWEB)

This paper addresses one source of degradation in OPV devices: the metal/organic interface. The basic approach was to study the completed device stability vs. the stability of the organic film itself as shown in subsequent devices fabricated from the films.

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The recent definition of a postulated thermal shock accident followed promptly by system repressurization, termed an overcooling or pressurized thermal shock accident, has set a large analysis and research effort into motion. The essential elements are concerned with defining the accident transients, evaluating the instrumentation and controls that cause the postulated accidents, and evaluating the metallurgical and structural mechanics aspects of the reactor vessel with respect to its failure potential. This paper poses the question faced by the Nuclear Regulatory Commission (NRC) for the vessel steel embrittlement, annealing, and surveillance dosimetry facets of this postulated accident and provides information on our plans for study of this problem as well as current status.

Science.gov (United States)

Lumbar epidural anesthesia is useful in a variety of chronic benign pain syndromes, including lumbar radiculopathy, low back pain syndrome, spinal stenosis, and vertebral compression fractures. Given the increased number of epidural nerve blocks being performed, some have reported unexplained complications of a transient or permanent nature and with varying degrees of severity. However, no case has been reported of a broken epidural needle tip retained in the lumbar facet joint area. This represents the first reported case presentation of foraminal stenosis developing in a patient after a retained epidural needle tip. PMID:21286465

Energy Technology Data Exchange (ETDEWEB)

A monolithic micromachined waveguide device or devices with low-loss, high-power handling, and near-optical frequency ranges is set forth. The waveguide and integrated devices are capable of transmitting near-optical frequencies due to optical-quality sidewall roughness. The device or devices are fabricated in parallel, may be mass produced using a LIGA manufacturing process, and may include a passive component such as a diplexer and/or an active capping layer capable of particularized signal processing of the waveforms propagated by the waveguide.

Energy Technology Data Exchange (ETDEWEB)

A method of augmenting heat transfer in the interior of a fluid or from the interface of a solid in contact to a fluid by utilizing electro hydrodynamic (EHD) phenomena has the following advantages: the heat transfer can be effected by using a relatively small, light-weight high voltage source and some simple structural members; no vibration and noise are generated; the method has a control function to control heat transfer by adjustment of field and voltage; and this method is effective in cost-saving. It is mass transfer by the electric force caused by interaction between true charges or polarized charges in a fluid and external electric filed that plays an important role in most of such heat transfer augmentation methods by EHD. Examples of heat transfer augmentation by EHD phenomena include electricaly induced convection, contribution of EHD effect to heat transfer accompanied with boiling, heat transfer by corona wind ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... 2nd Battalion, 20th Special Forces Group, Company B ... Headquarters, 29th Infantry Division, Joint Task Force-Augmentation ...

Science.gov (United States)

... United States Forces Command, Detachment 13 ... EUCOM Headquarters Support Detachment 1 ... 7th Joint Task Force Augmentation Team ...

Science.gov (United States)

This report describes an investigation of the performance of air-augmented waterjet thrusters. The investigation is divided into two parts. Part one describes a study of the injection of large diameter air bubbles to reduce heat transfer between the air and water and, thus, increase the thrust. This study is done analytically by solving the appropriate, governing equations. The results indicate that the approach is very worth-while since thrust can be increased ten percent as compared to air-augmentation with small bubbles. Several practical systems are discussed for injecting large air bubbles. Part two is an experimental investigation of the thrust produced under a wind range of conditions. The results show that a thrust increase of more than 20 percent can be achieved by air-augmentation. Further, the performance improves for larger thrust nozzles.

Science.gov (United States)

The goal of this experiment is to evaluate the usefulness of existing normal gravity two-phase flow heat transfer augmentation techniques under microgravity ...

Science.gov (United States)

[9] Rysdyk, R. T., and Calise, A. J., Fault Tolerant Flight control via Adaptive Neural Augmentation, AIAA. Guidance, Navigation, and Control Conference, Aug. ...

Science.gov (United States)

... increasing its economic results, tapping mew financial sources and augmenting its income, but also a basic task in financial and tax management. ...

UK PubMed Central (United Kingdom)

BackgroundObsessive-compulsive disorder is associated with a relevant impairment in social and interpersonal functioning and severe disability. This seems to be particularly true...Full Text Available

Science.gov (United States)

Mar 1, 2011 ... heat transfer augmentation in the stagnation region is presented. The effects of free stream turbulence and surface roughness on spanwise ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Clonidine Extended Release Augmentation of Psychostimulants in ADHD ADHD a Risk Factor for Substance Abuse; Cognitive Deficits Not a Predictor Commentary on Kollins et al.; Clonidine XR Augmentation for ADHD Pharmacologic Treatment of Childhood Insomnias Effects of Guanfacine Extended Release on Alertness in ADHD Long Term ADHD Drug Treatment Bipolar Disorder Rates Similar Across Selected Countries Group CBT Alone or Group CBT Plus SSRIs in Childhood Anxiety Resolution of Quetiapine-Induced Oral Dyskinesia From the FDA

International Nuclear Information System (INIS)

Heat transfer augmentation by straight grid spacers in rod bundles is studied for single phase flow and for post critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single phase flow is also examined. Governing heat transfer mechanisms are analyzed, and predictive formulations are established. For single phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. 18 refs.

International Nuclear Information System (INIS)

The applicability of Broyden's second method for accelerating the convergence of self-consistent electronic-structure calculations based on the linearized augmented-plane-wave method is discussed in terms of a W(001) surface calculation. It is found that its use results in a significant improvement in the convergence of the calculation, and based on this it is concluded that its use should increase the size of the systems for which such calculations are feasible.

Energy Technology Data Exchange (ETDEWEB)

High-performance heat transfer augmentation methods applicable in the forced convection field of heat exchangers include a method which requires no external drive means, such as the insertion of a turbulence augmentation object into the flow passage and the use of a wave-shaped flow passage, but disturbs the main stream of flow to raise the heat transportation effect thereby to augment heat transfer in the flow passage. The heat transfer characteristics and thermal performance ratio achieved when sinusoidal-shape plates are inserted instead of augmentation objects, such as cylinders, with a high shape-induced resistance were studied. As a result, the relationship between the resistance coefficient, average Nusselt number, heat transfer coefficient, and pitch was clarified. It has been revealed that the use of eddies with a large gap flow and recirculation area should be considered in order to get a ...

Energy Technology Data Exchange (ETDEWEB)

An attempt is made to augment the heat transfer efficiency by means of inserting an oscillating thin plate into a tube of the shell and tube heat exchanger. However, the heat transfer augmenting mechanism has not been fully explained. To elucidate this heat transfer augmenting mechanism, an investigation was given on the heat transfer characteristics of a tube inlet at its preliminary run area when a double-hinged oscillating thin plate is inserted in the inlet. As a result of the experiment, the heat transfer augmentation in the tube as a result of inserting the double-hinged oscillating thin plate was found effective when the preliminary inlet run area is treated as the object. However, in comparison of the effect with the heat transfer in a fully developed turbulent region, it was {eta}- 1. The result thus obtained explains that no sufficient turbulence can be obtained when the deflection angle of ...

Energy Technology Data Exchange (ETDEWEB)

The device is designed for automatic testing of the degree of discharge of tractive storage batteries (AB) for electric loaders, electric cars and electric ore locomotives. The basic electrical schematic of the device is cited.

British Library Electronic Table of Contents (United Kingdom)

In this paper we demonstrate the electrodeposition of nickel, a common ferromagnetic material, in various magnetically desirable shapes including nanowires, nanoparticles and highly faceted shells. In order to obtain three dimensional mesostructures, the electrochemical deposition of nickel was performed on highly oriented pyrolytic graphite (HOPG) under different electrolyte composition and deposition potential conditions. Under potentiostatic deposition at one distinct potential negative with respect to the reversible potential of nickel, three stages of nucleation and growth take place leading to a complex morphology of deposits. However, dual-pulse potential deposition and electrodeposition in low pH solutions causing hydrogen evolution, lead to nickel deposits in the form of nanowires...

Science.gov (United States)

Motion Camouflage (MC) is illuminated as a novel strategy in counterattacking anti-satellite by way of stealth trajectory scheduling. The dynamics model of MC in space is developed and a quadratic function with three boundary constraints is employed for trajectory determination. Based on the model a scenario is set to run the simulation. The results indicate given the designed acceleration input, the predator will be moved following a prescribed route, which precisely locates the predator between two objects at each time instant. In the last approaching phase, the motion is achieved with a big bumping rate which guarantees the power of this striking. Methods for deriving minimum fuel cost in the fixed approaching duration and the minimum approaching duration in limited acceleration input are proposed and are verified in the simulation. At last, camouflage is recognized as a multi-faceted affair, in which stealth trajectory design is considered an effective ...

Energy Technology Data Exchange (ETDEWEB)

A device made of amorphous silicon which exhibits inductive properties at certain voltage biases and in certain frequency ranges in described. Devices of the type described can be made in integrated circuit form.

International Nuclear Information System (INIS)

This experimental research investigates mixed convection and heat transfer augmentation by gaseous forced jets in a large enclosure, at conditions simulating those of passive containment cooling systems for Gen III+ passively safe reactors. The experiment is designed to measure the key parameters governing heat transfer augmentation by forced jets, and to investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio. The tests cover a variety of injection modes leading to flow configurations of interest for mixing and stratification phenomena in containments under accident conditions. Correlations for heat transfer augmentation by forced jets are developed and compared with experimental data. The characteristic recirculation speed inside the enclosure is introduced and analyzed. Steady stratified temperature distributions are compared ...

International Nuclear Information System (INIS)

The varestraint cracking test was carried out to assess the hot cracking tendency of alloy 800 at different welding conditions and augmented strain levels. The test results revealed that the hot cracking susceptibility of alloy 800 increases with increasing the heat input and augmented strain levels. This emphasizes the role of constraint either internally induced or externally applied to the welded structure. A cracking threshold or the minimum augmented strain (#epsilon#_m_i_n) below which no hot cracking takes place has been found to be 0.25 for alloy 800. Also, the Critical Strain Rate to Time (CSS) required to cause cracking was found to be 6.42x10"-"3 sec"-"1 at welding condition of 100 Amp, 13 Volt and 140 mm/min. (author).

Energy Technology Data Exchange (ETDEWEB)

This report describes the experimental researches on the polarization Characteristics of symmetric GaAs-GaAlAsP double heterojunction lasers, and analyses the mode-competition processes of these lasers. The experiments showed that semiconductor laser is emitted spontaneously and does not indicate optical polarization characteristic when it is biased under the threshold current. When it is biased above the threshold current, the laser for thin active layer of d = 0.15approx.0.40 ..mu..m is generally observed only in fundamental order mode, and TE mode polarization is predominant. At this time, polarization selection is dependent on Fabry-Perot cavity facet (cleaved face) mode reflectivity R/sub 0/. But TM mode is saturated at the threshold, the current applied to the laser above the threshold is used to enhance the TE polarization when the active thickness d is larger than 0.4 ..mu..m, the competition between TE and TM mode, fundamental order an higher order mode ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Single-event burnout (SEB) sensitivity was tested for power MOSFET devices, JTMCS081 and JTMCS062, which were made in Institute of Microelectronics, Chinese Academy of Sciences, using californium-252 simulation source. SEB voltage threshold was found for devices under test (DUT). It is helpful for engineers to choose devices used in satellites. (authors)

International Nuclear Information System (INIS)

... amplification exhaust systems fluidic control devices gloveboxes pressure

International Nuclear Information System (INIS)

... bwr type reactors closures fluidic control devices operation performance pwr

J-STORE (Japan)

Full Text Available

Science.gov (United States)

An integrated mirrorless bistable optical device based on the Mach-Zehnder interferometric optical switch has been proposed and demonstrated experimentally using a Ti:LiNbO3 waveguide. The resulting device is capable of combining more than two of them to realize multifunctional optical devices such as optical multivibrators.

Energy Technology Data Exchange (ETDEWEB)

We discuss the initial development of a concentrator device based on the GaInP/GaAs monolithic tandem cell structure. The very high one-sun efficiency of this device, coupled with its characteristic low operating current, make this a promising candidate for use under high concentration. Test results for a prototype device are presented. This device achieves an efficiency of 29.5% at a concentration of 102 suns.

International Nuclear Information System (INIS)

... coolants departure nucleate boiling fluid flow fluidic control devices fuel

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Power devices such as MOSFETSs and IGBTs, include parasitic structures that can give rise to destructive failures such as breakdown and latch-up. To determine a suitable strategy for device radiation hardening, simulation software like MEDICI-2D can be used to model the effects of technological modifications and device parameters that are difficult to measure experimentally. (authors).

J-STORE (Japan)

Full Text Available

Science.gov (United States)

PMID:21820543

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The authors report here on an experimental study of heat transfer augmentation in turbulent flow. Enhancement strategies employed in this investigation are based on the near-wall mixing processes induced in the sublayer through appropriate wall and near-wall streamwise-periodic disturbances. Experiments are performed in a low-turbulence wind-tunnel with a high-aspect-ratio rectangular channel having either (a) two-dimensional periodic microgrooves on the wall, or (b) two-dimensional microcylinders placed in the immediate vicinity of the wall. It is found that microdisturbances placed inside the sublayer induce favorable heat-transport augmentation with respect to the smooth-wall case, in the near-analogous momentum and heat transfer behavior are preserved; a roughly commensurate increase in heat and momentum transport is termed favorable in that it leads to a reduction in the pumping power penalty at fixed heat removal rate. The study shows ...

Energy Technology Data Exchange (ETDEWEB)

Experiments are performed to investigate the single-phase flow and flow-boiling heat transfer augmentation in 3D internally finned and micro-finned helical tubes. The tests for single-phase flow heat transfer augmentation are carried out in helical tubes with a curvature of 0.0663 and a length of 1.15 m, and the examined range of the Reynolds number varies from 1000 to 8500. Within the applied range of Reynolds number, compared with the smooth helical tube, the average heat transfer augmentation ratio for the two finned tubes is 71% and 103%, but associated with a flow resistance increase of 90% and 140%, respectively. A higher fin height gives a higher heat transfer rate and a larger friction flow resistance. The tests for flow-boiling heat transfer are carried out in 3D internally micro-finned helical tube with a curvature of 0.0605 and a length of 0.668 m. Compared with that in the smooth helical tube, the boiling heat ...

Science.gov (United States)

Heating and cooling by impinging jets is widely used in various engineering applications, due to the high heat transfer rates prevailing in the vicinity of the stagnation point. The authors have been able to utilize acoustically excited turbulence for the...

British Library Electronic Table of Contents (United Kingdom)

Abstract Objectives: The purpose of this study was to evaluate the osseointegration of the dental implants placed into the mandible augmented with different techniques in pigs. Material and methods: Four adult domestic pigs were used. Horizontal augmentation of the mandible was performed in animals by using vascularized femur flap (VFF), non-vascularized femur graft (NVFG) and monocortical mandibular block graft (MG). After 5 months of healing 10 dental implants were placed into each augmented site. The pigs were sacrificed after 3 months of healing. Undecalcified sections were prepared for histomorphometric analysis. Results: Mean bone-implant contact (BIC) values for implants placed into MG, NVFG and VFF were 57.38 11.97%, 76.5 7.88%, 76.53 8.15%, respectively. The BIC values of NVFG and...

UK PubMed Central (United Kingdom)

Recent studies suggest that calcium influx via L-type calcium channels is necessary for psychostimulant-induced behavioral sensitization. In addition, chronic amphetamine upregulates subtype...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This volume is divided into the following sections: (1) fundamentals of convection heat transfer; (2) fundamentals of heat transfer with impinging jets; and (3) fundamentals of heat transfer augmentation. Separate abstracts were prepared for most papers in this volume.

Energy Technology Data Exchange (ETDEWEB)

The effects of various approximations used in performing augmented-plane-wave calculations were studied for elements of the fifth and sixth columns of the Periodic Table, namely V, Nb, Ta, Cr, Mo, and W. Two kinds of approximations have been checked: (i) variation of the number of k points used to iterate to self-consistency, and (ii) approximations for the treatment of the core states. In addition a comparison between relativistic and nonrelativistic calculations is made, and an approximate method of calculating the spin-orbit splitting is given.

International Nuclear Information System (INIS)

A large amount of energy has been consumed so far in so called matured industries such as iron and steel, oil refinery, petrochemical, ceramic, paper and pulp manufacturing and so forth. A successive stimulation on the preceding industries has to be enhanced from a technological viewpoint in order to maintain a further development based on novel and innovative technologies. In this regard, energy technology has become and will be increasingly important in a high temperature system so that the basic concept for heat transfer augmentation methods by thermal radiation is reviewed briefly in accord with the recent developments together with theoretical background and the prominent features. The heat transfer augmentation related to thermal radiation is summarized.

International Nuclear Information System (INIS)

Local-density-approximation calculations of the H-point phonon frequency of molybdenum were carried out using a new superlinearized augmented-plane-wave basis. The calculated frequency is in quite good agreement with experiment. This indicates that the effect of the many-body renormalization of the electronic states near the Fermi energy on this frequency is smaller than previously suggested. The superlinearized basis and its use to circumvent computational difficulties associated with extended semicore states such as the 4p state of molybdenum is described.

Energy Technology Data Exchange (ETDEWEB)

Fins serve as heat transfer augmentation features in solar air heaters; however, they increase pressure drop in flow channels. Pin fins are relatively good heat transfer augmentation features with superior aerodynamic performance, and as a result find application in some solar air heaters. The exergy optimization method is employed in sizing the pin fin. Results indicate that high efficiency of the optimized fin improves the heat absorption and dissipation potential of a solar air heater. With optimum fin efficiency and superior absorptive coating quality, useful energy losses can be minimized. Some important observations pertinent in design are made. (author)

CERN Document Server

Choosing a medical device is complex and requires a transparent process based on reason, evidence and assessment of prioritized public health needs. Poor choices lead to inappropriate use or non-use of medical devices and a waste of resources.This report suggests how an agenda to improve access to appropriate medical devices could be devised from applying the crucial 4 components - Availability, Accessibility, Appropriateness, and Affordability, to the 15 global high-burden diseases and some cross-cutting issues. The results of this exercise suggest several areas of research necessary to help

Energy Technology Data Exchange (ETDEWEB)

The theoretical performance of ideal single- and multijunction cells are compared at 100xconcentration under a range of cloudless-sky conditions. The sensitivities of device performance to cell temperature and spectral variations are shown to depend on the number of junctions (one, two or three), the way in which the junctions are connected (series, parallel or independent), and the band gaps of the devices. The average performances of all of the multijunction devices surpass that of a single-junction GaAs device, but the inconsistency in performance of some of the multijunction devices is significant for large variations in cell temperature and incident spectrum. The choice of band gap and connection scheme is more important than the number of junctions in determining the consistency of device performance. (orig.).

Science.gov (United States)

PNAS-4, a novel pro-apoptotic gene activated during the early response to DNA damage, can inhibit proliferation via apoptosis when overexpressed in some tumor cells. Recent studies have indicated that honokiol can induce apoptosis, inhibit angiogenesis, and suppress tumor growth. In the present study, we investigated whether mouse PNAS-4 (mPNAS-4) could augment the apoptosis of tumor cells induced by honokiol in vitro, and whether the antiangiogenic activity of honokiol and induction of apoptosis by mPNAS-4 could work cooperatively to improve the antitumor efficacy in vivo. In vitro, mPNAS-4 inhibited proliferation of murine colorectal carcinoma CT26 and Lewis lung carcinoma LL2 cells through induction of apoptosis, and significantly augmented the apoptosis of CT26 and LL2 cells induced by honokiol. Compared with treatment with mPNAS-4 or honokiol alone, in vivo systemic administration of an expression plasmid encoding mPNAS-4 and low-dose ...

Energy Technology Data Exchange (ETDEWEB)

What utilizes the effect of electrohydrodynamical technique (EHD), as one of heat transfer augmentation methods, is methodically frequented and partially prepared to be put to practical use. Then, the heat transfer augmentation effect on nucleate boiling, utilizing the EHD effect, was both experimentally and theoretically studied from both the applicative and basic viewpoints. By adding fleon with 2wt% ethyl alcohol, higher in electric conductivity, in order to have the mitigation time of electric charge correspond to the bubbling frequency of bubble, the heat transfer augmentation was enabled to be about 8.5 times as high as that without impressing the electric field. As a result of observing the behavior of bubble in the electric field, was observed a phenomenon of bubble, moving from place to place, without ascending, on the plane electrode plate, by which could be found one of causes of the heat transfer ...

Energy Technology Data Exchange (ETDEWEB)

Performance of SRF cavities are limited by non-linear localized effects. The variation of local material characters between "hot" and "cold" spots is thus of intense interest. Such locations were identified in a BCP-etched large-grain single-cell cavity and removed for examination by high resolution electron microscopy (SEM), electron-back scattering diffraction microscopy (EBSD), optical microscopy, and 3D profilometry. Pits with clearly discernable crystal facets were observed in both "hotspot" and "coldspot" specimens. The pits were found in-grain, at bi-crystal boundaries, and on tri-crystal junctions. They are interpreted as etch pits induced by surface crystal defects (e.g. dislocations). All "coldspots" examined had qualitatively low density of etching pits or very shallow tri-crystal boundary junction. EBSD revealed the crystal structure surrounding the pits via crystal phase orientation mapping, while 3D profilometry gave information on the depth and size ...

Science.gov (United States)

The purpose of this investigation was to determine the association between gender and the prevalence and incidence of patellofemoral pain syndrome (PFPS). One thousand five hundred and twenty-five participants from the United States Naval Academy (USNA) were followed for up to 2.5 years for the development of PFPS. Physicians and certified athletic trainers documented the cases of PFPS. PFPS was defined as retropatellar pain during at least two of the following activities: ascending/descending stairs, hopping/jogging, prolonged sitting, kneeling, and squatting, negative findings on examination of knee ligament, menisci, bursa, and synovial plica, and pain on palpation of either the patellar facets or femoral condyles. Poisson and logistic regressions were performed to determine the association between gender and the incidence and prevalence of PFPS, respectively. The incidence rate for PFPS was 22/1000 person-years. Females were 2.23 times (95% CI: 1.19, 4.20) more ...

Energy Technology Data Exchange (ETDEWEB)

A multi-faceted research program has been performed to investigate in detail several aspects of free and forced convective cooling of underground electric cable systems. There were two main areas of investigation. The first one reported in this volume dealt with the fluid dynamic and thermal aspects of various components of the cable system. In particular, friction factors for laminar flow in the cable pipes with various configurations were determined using a finite element technique; the temperature distributions and heat transfer in splices were examined using a combined analytical numerical technique; the pressure drop and heat transfer characteristics of cable pipes in the transitional and turbulent flow regime were determined experimentally in a model study; and full-scale model experimental work was carried out to determine the fluid dynamic and thermal characteristics of entrance and exit chambers for the cooling oil. The second major area of activity, ...

Energy Technology Data Exchange (ETDEWEB)

Tantalum and tantalum-based thin films have gained precedence as the diffusion barrier for copper interconnects used in the latest generation of integrated circuits (ICs). The paper presents insight and observations on the covariance of texture and grain size of wrought tantalum sputtering targets and their influence on sputtering performance. Previous studies involving deposition trials of tantalum targets of varying metallurgical character had demonstrated that both grain size and textural homogeneity is critical for assuring reliable sputtering performance of tantalum. Subsequently, a model had been proposed to prescribe how localized texture bands and orientation clusters in tantalum are effectively resistant to sputter erosion. In this paper, results of atomic force microscopy (AFM) and orientation imaging microscopy (OIM{sup TM}) analyses on the eroded surface of a tantalum sputtering target are presented. Initial findings support the model's hypothesis regarding the ...

Energy Technology Data Exchange (ETDEWEB)

Magnetic coupling between two or more metal centers is an important facet of d- and f-block transition metal chemistry due to its implications in chemical bonding. With respect to actinide metals, magnetic coupling between polymetallic actinide centers is less well-known. Of the few documented examples, only one bimetallic uranium(V) complex, [(MeC{sub 5}H{sub 4}){sub 2}U]{sub 2}[{mu}-1,4-N{sub 2}C{sub 6}H{sub 4}] (1), has unequivocally demonstrated antiferromagnetic coupling. This complex employs a {pi}-conjugated 1,4-phenylenedimide ligand system which bridges the two f{sup 1}-metal centers and enables antiferromagentic coupling between unpaired f-e1ectrons residing in a {pi}-symmetry orbital. In this communication, we report the synthesis of a dimeric bis(imido) uranium(V) iodide complex and demonstrate with magnetic susceptibility measurements and density functional theory (DFT) calculations that the f{sup 1}-uranium centers display antiferromagnetic coupling ...

Energy Technology Data Exchange (ETDEWEB)

Science and technology could be revolutionized by quantum computers, but building them from solid-state devices will not be easy. Robert W Keyes of IBM's research division outlines the challenges in scaling up the technology from lab experiments to practical devices. (U.K.)

International Nuclear Information System (INIS)

The patent relates to fluid operated devices for moving articles. The machine may be used in filling a nuclear fuel canister with fuel pellets where there is a tendency for out of squareness of pellets to produce a jam condition readily cleared by a modest force. (U.K.).

Science.gov (United States)

Coke-fired cupola furnaces were improved and made suitable for the production of high-quality casting melts by numerous additional devices. Moreover, they were equipped with environmental protection systems with numerous dust separation devices and afterb...

Energy Technology Data Exchange (ETDEWEB)

In this paper we discuss the effect on the emittance of the residual dispersion in the insertion devices. The dispersion in the straights could be generated by the lattice error, trim dipole, and insertion device. The effect on the emittance is examined, and the dispersion tolerances are given for the NSLS-11.

UK PubMed Central (United Kingdom)

The biomechanical nature of the arterial system and its major disease states provides a series of challenges to treatment strategies. Endovascular device design objectives have mostly centered on short-term...Full Text Available

Science.gov (United States)

...limited to, emission control devices, pumps, filters, muck cookers, stills, solvent tanks, solvent containers, water separators...facility that meets the conditions of § 63.320(g). Muck cooker means a device for heating perchloroethylene-laden...

International Nuclear Information System (INIS)

The influence of the main factors on device efficiency of pulsed liquid jet pump with gas-liquid piston is analysed, the theoretical equation and its time-averaged solution of pulsed liquid jet pump device efficiency are derived. The theoretical and experimental results show that the efficiency of transmission of energy and mass to use pulsed jet is greatly raised, compared with steady jet, in the same device of liquid jet pump. The calculating results of time-averaged efficiency of pulsed liquid jet pump are approximately in agreement with the experimental results in our and foreign countries

Science.gov (United States)

... Abstract : MANY THIN FILM ACOUSTO-OPTIC INTERACTION EXPERIMENTS FOR ... CONVERTERS, AND FOR FAST SWITCHES HAVE BEEN ...

International Nuclear Information System (INIS)

... Union (INTAS), Brussels (Belgium) Science and Technology Center in Unkraine,

Science.gov (United States)

... This is achieved by the use of a unique logic circuit employing a plurality of flip-flop devices, multivibrators and AND gates. ...

Science.gov (United States)

... increasing photorealism. Furthermore, developments in audio technology continue to increase the spatial awareness of users in VEs. ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses design considerations for the recently introduced GaInP/GaAs monolithic tandem concentrator cell. The prototype device achieves a peak efficiency of 30.2% in a range of 140--180 suns, making this the first two-terminal device to demonstrate a verified efficiency exceeding 30%. At 425 suns the efficiency is still above 29%. The authors focus on the issues of grid design, top-cell thickness, and antireflectance coat. They also examine ways in which these aspects of the device may be modified to provide further performance improvements for future devices.

J-STORE (Japan)

Full Text Available

Science.gov (United States)

... initiation) Pressed e Combustible Cartridge Cases Quantity-Distance Table ... Combustible Cartridge Cases, and Electrically Exploded Devices in ...

Energy Technology Data Exchange (ETDEWEB)

A slurry intake device is proposed which contains an inlet sleeve, housing with grating installed with the discharge end in the zone of the slurry outlet, and hinged deflector. In order to conserve the clay mud, it is equipped with a tie rod and two-arm lever which is kinematically linked to the deflector and the grating. It is installed by hinges in relation to the housing and the latter is attached by hinges to the inlet sleeve. The deflector is arranged in the zone of slurry outlet. The device is distinguished by the fact that the deflector is equipped with a cantilever on which a fixable weight is attached.

CERN Document Server

A self-organizing particle swarm is presented. It works in dissipative state by employing the small inertia weight, according to experimental analysis on a simplified model, which with fast convergence. Then by recognizing and replacing inactive particles according to the process deviation information of device parameters, the fluctuation is introduced so as to driving the irreversible evolution process with better fitness. The testing on benchmark functions and an application example for device optimization with designed fitness function indicates it improves the performance effectively.

Energy Technology Data Exchange (ETDEWEB)

The audible noise produced by corona on high-voltage transmission lines has several characteristics that differentiate it from other community noises. Transmission line noise is quite broadband and has a significant high frequency content. Special instrumentation designed to measure this type of noise pollution is described. All measuring systems have the same three basic elements: a transducer, a processing device, and an output device. Recorders, microphone devices, frequency analyzers, and meteorological instrumentation are discussed.

Science.gov (United States)

The dynamic behavior of electrooptic bistable devices with delayed feedback is investigated theoretically and experimentally. The operation principle of the system is analyzed by the method of iterated maps. Stable, bistable, periodic, higher periodic, and chaotic solutions are discussed and realized experimentally by using an integrated Mach-Zehnder interferometer on LiNbO3 as a basic nonlinear element. Taking into account the periodic modulator characteristic, the application of this device as a simple and fast bistable and monostable multivibrator is demonstrated. In addition, the synchronization properties of the astable multivibrator are investigated.

Energy Technology Data Exchange (ETDEWEB)

This is a patent for a device to increase compaction of the loaded batch in a coking chamber that assures a balanced compaction of the batch from the upper to the bottom layer. The leveling rod has a device on the external end that causes the rod to shift vertically and bring pressure on the material and the pressing attachment. Opposite the loading hoppers of the coking chambers there are guides that ensure the rod will be sunk perpendicularly into the loaded material.

International Nuclear Information System (INIS)

The invention concerns a container for the long term storage of irradiated nuclear reactor fuel elements, which consists mainly of a basic body, at least one lid and an outside ring shaped lid tightening device, which acts on the basic body and the lid and holds the contact surface of the lid tight against the contact surface of the basic body, where the basic body, lid and the lid tightening device consist of corrosion-proof materials. (orig./HP).

Energy Technology Data Exchange (ETDEWEB)

The purpose of the invention is to simplify assembly and to reduce labor intensity. This is achieved by the fact that the assembly shaft is positioned in a hawser, while its wall which is turned towards the body of the installation is combined with the hawser wall, where a U shaped opening is made in the wall of the assembly shaft, along the edges of which there is a hermetically sealing device, while the bottom of the body of the offshore drilling rig is equipped with a rigid insert attached with the capability of adjoining it with the hermetically sealing device.

Energy Technology Data Exchange (ETDEWEB)

An assessment of the cooling requirements for fusion reactor components, such as the first wall and limiter/divertor, was carried out using pressurized water as the coolant. In order to establish the coolant operating conditions, a survey of the literature on departure from nucleate boiling, critical heat flux, asymmetrical heating and heat transfer augmentation techniques was carried out. The experimental data and the empirical correlations indicate that thermal protection for the fusion reactor components based on current design concepts can be provided with an adequate margin of safety without resorting to either high coolant velocities, excessive coolant pressures, or heat transfer augmentation techniques. If, however, the future designs require heat transfer enhancement techniques, experimental verification would be necessary since no data on heat transfer augmentation techniques exist for complex geometries, ...

Energy Technology Data Exchange (ETDEWEB)

An assessment of the cooling requirements for fusion reactor components, such as the first wall and limiter/divertor, was carried out using pressurized water as the coolant. In order to establish the coolant operating conditions, a survey of the literature on departure from nucleate boiling, critical heat flux, asymmetrical heating and heat transfer augmentation techniques was carried out. The experimental data and the empirical correlations indicate that thermal protection for the fusion reactor components based on conventional design concepts can be provided with an adequate margin of safety without resorting to either high coolant velocities, excessive coolant pressures, or heat transfer augmentation techniques. If, however, the future designs require unconventional shapes or heat transfer enhancement techniques, experimental verification would be necessary since no data on heat transfer augmentation techniques exist for ...

International Nuclear Information System (INIS)

In this thesis, a new ab-initio method for molecular dynamics within the framework of density functional theory was developed and implemented. It is strongly related to the projector-augmented-wave method (PAW) by P. Bloechl, but also includes elements of a pseudocharge method proposed by M. Weinert for the full-potential linearized augmented plane wave method (FLAPW). Like the FLAPW-method, the PAW-method is an all-electron method. In the later case, the hamiltonian takes quite a simple form similar to the one obtained when using normconserving Kleinman-Bylander-type pseudopotentials or ultrasoft Vanderbilt pseudopotentials. The PAW-method allows for an efficient calculation of systems containing virtually any element of the periodic table, including those which require high numerical effort when treated using normconserving pseudopotentials (e.g. 2p-elements like oxygen or 3d-transitional metals like copper). In addition, a higher accuracy ...

International Nuclear Information System (INIS)

A semirelativistic two-component extended linear augmented plane-wave k#centre dot#p method is described. In order to ensure a high accuracy of the k#centre dot#p method, it is necessary to include into the radial-basis set, which is used for the augmentation of the plane waves, functions that are neither solutions of the Schrodinger equation nor their energy derivatives. The usual scalar relativistic procedure, which is nonlinear in energy, is not applicable to such basis sets. As an alternative, we suggest an approximation to the Foldy-Wouthuysen Hamiltonian that produces an explicitly Hermitean matrix in the augmented plane wave representation. The technique is applied to the calculation of the full dielectric matrix and optical properties of palladium and platinum metals over the photon energy region up to 100 eV. Special attention is paid to the far ultraviolet absorption by the excitations of semicore Pd 4p and Pt 5p ...

International Nuclear Information System (INIS)

Heat transfer augmentation due to surface radiation in an annulus with fins was investigated both theoretically and experimentally for fully developed laminar flow. The system considered in the present study was an array of axially internal and straight fins attached to the outer tube wall. Analytical solutions were given for 4, 8, 16, 24, 32 fins and for the ratios of the fin height to the passage clearance, 0, 0.2, 0.4, 0.5, 0.6, 0.8. The experiments were performed with air as the working fluid for radius ratio of 1.45, 16 fins and for Reynolds numbers ranging from 500 to 2000. The numerically predicted results of the convective/radiative heat transfer for the present case were in good agreement with the experimental data. It was found that the heat transfer augmentation coefficient attained a maximum value of 1.45 for 32 fins and for a dimensionless fin height of 0.65.

Energy Technology Data Exchange (ETDEWEB)

Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass transfer coefficients. Downwash of the rotating secondary flow, reattachment of ...

Energy Technology Data Exchange (ETDEWEB)

The heat transfer a characteristics and friction factor in the horizontal double pipes of flat tubes with full length helical screw element of different twist ratio and helical screw inserts with different spacer length are investigated. Cold and hot water are used as working fluid in tube side and shell side respectively. The experiments covered a range of Reynolds numbers 5.7 x 10{sup 2} {<=} Re {<=} 1.31 x 10{sup 3}. The effect of spacer length on the heat transfer augmentation and friction factor and the effect of twist ratio on heat transfer augmentation and friction factor have been presented separately. The study shows that, the Nusslet number (Nu) and friction factor (f) decrease with the increase of S or Y for flat tube. The comparison between the data of present plain circular with that of previous plain circular tube showed a good agreement between them but the data of present plain flat tube showed a higher in heat ...

International Nuclear Information System (INIS)

The energy bands and the nature of the conduction electrons have been studied for three intermetallic compounds of dysprosium. e.g., DyZn, DyCu and DyRh, following the augmented plane wave method. Density of states results are given and have implications for the stability of the structure of the intermetallic compounds of dysprosium. The charge densities and the number of conduction electrons inside and outside the APW spheres in each of these compounds are calculated; it is shown that the character of conduction electrons within the Dy APW sphere is principally of d type for all the compounds. The consequence of the predominance of d electron in the conduction bands on the various physical parameters is discussed. (author).

International Nuclear Information System (INIS)

The electronic structure and optical properties in tetragonal ceramics PbTiO_3, are studied by using full-potential linearized augmented plane wave method in density functional theory with the generalized gradient approximation by WIEN2K package. The theoretical calculated optical properties and energy loss spectrum yield a static refractive index of 2.59 and a plasmon energy of 22.7eV for the tetragonal phase. The effective electron number at low energy saturates near 22-23eV with the value of 50 for the effective electron number. The results show a indirect band gap of 2.2eV at the I' point in the Brillouin zone. The :calculated band structure and density of states of PbTiO_3 agree with previous experimental and theoretical results.

International Nuclear Information System (INIS)

O.K. Andersen has recently introduced a linear augmented plane wave method (LAPW) for the calculation of electronic structure that was shown to be computationally fast. A more general formulation of an LAPW method is presented here. It makes use of a freely disposable number of eigenfunctions of the radial Schroedinger equation. These eigenfunctions can be selected in a self-consistent way. The present formulation also results in a computationally fast method. It is shown that Andersen's LAPW is obtained in a special limit from the present formulation. Self-consistent test calculations for copper show the present method to be remarkably accurate. As an application, scalar-relativistic self-consistent calculations are presented for the band structure of FCC lanthanum. (author).

Energy Technology Data Exchange (ETDEWEB)

A numerical investigation for forced convection in a constant-temperature parallel plate channel with porous cavity and block alternately emplaced on the bottom plate is presented in this work. The Brinkman-Forchheimer-extended Darcy model, which accounts for the effects of impermeable boundary and inertia, is used to characterize the flow field inside the porous region. Solutions of the coupled governing equations are carried out through the stream function-vorticity analysis. The characteristics of fluid flow and forced convection heat transfer have been obtained by the examinations of various governing parameters, such as the Reynolds number, Darcy number, inertial parameter, Prandtl number, and two geometric parameters. Several interesting phenomena such as the heat transfer augmentation in the channel were presented and discussed. The results of this investigation indicate that the size of recirculation caused by porous block will have a profound effect on the ...

International Nuclear Information System (INIS)

This experiment investigated the effects of free-stream turbulence intensity, length scale, Reynolds number, and leading-edge velocity gradient on stagnation-region heat transfer. Heat transfer was measured in the stagnation region of four models with elliptical leading edges downstream of five turbulence-generating grids. Stagnation-region heat transfer augmentation increased with decreasing length scale but an optimum scale was not found. A correlation was developed that fit heat transfer data for isotropic turbulence to within #+-#4 percent but did not predict data for anisotropic turbulence. Stagnation heat transfer augmentation caused by turbulence was unaffected by the velocity gradient. The data of other researchers compared well with the correlation. A method of predicting heat transfer downstream of the stagnation point was developed. 28 refs., 12 figs., 4 tabs.

Energy Technology Data Exchange (ETDEWEB)

A numerical analysis is made of the unsteady flow and heat transfer characteristics of mixed convection in a vertical block-heated channel with and without installing an inclined plate above an upstream block. Parameter studies including the inclined plate angle, Reynolds number (ranging from 260 to 530), and Grashof number (in the range of 0--3,200,000) on heat transfer performance have been explored in detail. The results show that the installation of an inclined plate in the vertical block-heated channel can effectively augment the blocks` heat transfer performance in the channel. This can be applied to heat exchangers.

International Nuclear Information System (INIS)

From the first principles total energy calculations based on full-potential linear augmented plane wave method (FPLAPW), the elastic properties of XPt_3 (X=V, Cr, Mn, Fe, Co, Ni) are reported here. Theoretical values of Young's modulus, shear modulus, Poisson's ratio and Debye temperature are estimated from the computed elastic constants. From the analysis of the ratio of shear to bulk modulus, it is found that these intermetallic compounds are ductile in nature except CrPt_3, which is brittle. The calculated results are compared with other reported values.

Science.gov (United States)

We developed mice with germline endogenous expression of oncogenic Hras to study effects on development and mechanisms of tumor initiation. They had high perinatal mortality, abnormal cranial dimensions, defective dental ameloblasts, and nasal septal deviation, consistent with some of the features of human Costello syndrome. These mice developed papillomas and angiosarcomas, which were associated with Hras(G12V) allelic imbalance and augmented Hras signaling. Endogenous expression of Hras(G12V) was also associated with a higher mutation rate in vivo. Tumor initiation by Hras(G12V) likely requires augmentation of signal output, which in papillomas and angiosarcomas is achieved via increased Hras-gene copy number, which may be favored by a higher mutation frequency in cells expressing the oncoprotein. PMID:19416908

International Nuclear Information System (INIS)

The electronic structures of BaSnO_3, BaSbO_3, and BaPbO_3, calculated using an extended general-potential linearized augmented-plane-wave method, are reported. The electronic structures of BaSnO_3 and its 6s analog BaPbO_3 are found to be very different, explaining the absence of superconductivity in the Ba(Sn,Sb)O_3 system. These differences are explained by a combination of the relativistic lowering of the 6s states and ion-size effects. Muffin-tin-approximation augmented-plane-wave calculations for BaSnO_3 are also reported and the utility of the muffin-tin approximation for this and similar materials is discussed in terms of the differences between the two sets of calculations.

CERN Document Server

The necessity of supporting more and more social interaction (and not only the mere information sharing) in online environments is the disruptive force upon which phenomena ascribed to the Web2.0 paradigm continuously bud. People interacting in online socio-technical environments mould technology on their needs, seamlessly integrating it into their everyday life. MUVEs (Multi User Virtual Environments) are no exception and, in several cases, represent the new frontier in this field. In this work we analyze if and how MUVEs can be considered a mean for augmenting communities (and more in general people) life. We trace a framework of analysis based on four main observations, and through these lenses we look at Second Life and at several projects we are currently developing in that synthetic world.

British Library Electronic Table of Contents (United Kingdom)

BackgroundWave reflection during the systole increases left ventricular (LV) pressure, tension-time index (TTI) and myocardial oxygen requirement. The purpose of this study was to extract that component of extra myocardial oxygen requirement that is due to early systolic wave reflection, define it as wasted effort (?Ew), and examine its relationship to LV hypertrophy (LVH).MethodsRadial artery pressure waveforms were recorded using applanation tonometry and central aortic waveforms generated in 98 patients with untreated hypertension. Aortic augmentation index (AIa), wave reflection amplitude (i.e., aortic augmented pressure (AG)) and systolic duration (ED?Tr), ejection duration (ED) and round-trip travel time of the pressure wave (Tr) were calculated from the aortic waveform, a...

Energy Technology Data Exchange (ETDEWEB)

A real time neutron radiography system has been developed at the University of Michigan Phoenix Memorial Laboratory (PML) and has recently been used to test the imaging capabilities of a neutron imaging device developed by Lixi, Inc. of Downers Grove, Illinois. This device uses an input phosphor that is high in gadolinium to generate a light image which is then sent through an intensifier stage to provide images that can be viewed by eye, video camera, or standard 35 mm camera. It was determined that this device provides images of much higher resolution and sensitivity than those obtained with the imaging system currently being used at PML. Using computerized image enhancement techniques, the images obtained with the Lixi neutron imaging device can then be further enhanced or processed to obtain quantitative information on the object being imaged.

Energy Technology Data Exchange (ETDEWEB)

We summarize recent developments in x-ray microscopy of polymers by focusing on the characterization of organic electronic devices. The quantitative compositions of model polymer blends have been mapped at a resolution of {approx}35 nm. Since it could be inferred that these devices have structures smaller than 35 nm, quantitative compositional mapping at length scales below the present resolution limit of x-ray microscopy is required. Organic devices thus serve to both highlight the success of NEXAFS microscopy to date, but to also outline the very real need for higher spatial resolution. New approaches to create improved optics or different acquisition modalities are required if x-ray microscopy is to make sustained contributions to such an important area of research as organic devices.

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to a light weight underground pipe or cable installing device adapted for use in a narrow and deep operating trench. More particularly this underground pipe installing device employs a pair of laterally movable gates positioned adjacent the bottom of the operating trench where the earth is more solid to securely clamp the device in the operating trench to enable it to withstand the forces exerted as the actuating rod is forced through the earth from the so-called operating trench to the target trench. To accommodate the laterally movable gates positioned adjacent the bottom of the narrow pipe installing device, a pair of top operated double-acting rod clamping jaws, operated by a hydraulic cylinder positioned above the actuating rod are employed.

Energy Technology Data Exchange (ETDEWEB)

This article describes a flexible and extensible infrastructure for applying Web-Technologies to embedded systems.The presented approach develops a Three-level-Architecture consisting of the embedded system, the universal Remote-Access-Server and the Remote-Access-Client. A system-spanning general interface allows the binding of embedded systems in order to access their process data. Additionally, this procedure facilitates a flexible processing of the device data, so that it is ready to be used by different control devices. To ensure flexibility - connecting different devices on the one side and providing information for different clients like PC, PDA or mobile phone on the other side - a new XML-based description language (Service Description Markup Language - SDML) is introduced. The SDML documents contain information about connected embedded systems, reusable device data and the presentation ...

Energy Technology Data Exchange (ETDEWEB)

The electronic structure of the C15, or cubic-Laves-phase material, UAl/sub 2/ has been calculated using the linearized relativistic augmented-plane-wave method. The anomalous behavior of the electrical resistivity, specific heat, and magnetic susceptibility can be explained by the fine structure of the density of states near the Fermi energy alone, without the necessity of the introduction of drastic spin fluctuations or many-body effects.

International Nuclear Information System (INIS)

The electron-phonon coupling constant lambda has been calculated for vanadium. The electron energy bands and wave functions were obtained from a model augmented plane wave muffin-tin potential. The electron-phonon matrix elements were evaluated using the rigid-ion approximation and the measured phonon spectra. The results show that lambda is strongly affected by d-f scattering.

Energy Technology Data Exchange (ETDEWEB)

This paper establishes a standardization procedure in which results are presented in ready-to-use charts for the economic evaluation of biogas plants. It is hoped this work will alleviate controversial reports on cost-effectiveness of biogas systems. Also, it is found that these systems are the most economic among renewable energy systems using a standardized procedure for their comparison augmented by the generated spider diagrams wherein most probable costing production values for each system are directly compared. (author).

Energy Technology Data Exchange (ETDEWEB)

To simulate the effects of the breakup channel on rearrangement amplitudes, the conventional coupled-reaction-channel (CRC) expansion is augmented by pseudoreaction channels. The construction of the projector for the extended CRC space is discussed, and transition-operator equations on this space are given. By solving the full and post-approximation forms of the CRC equations for a model three-particle problem, the crucial role played by the nonorthogonality terms is demonstrated.

International Nuclear Information System (INIS)

The wavefunction of a positron in ReO is calculated using the augmented-plane-wave method. Due to the loosely-packed structure of ReO_3, the ground-state GAMMA_1 wavefunction exhibits a marked anisotropy particularly around the oxygen ions, and a large fraction of a positron is distributed in the interstitial region. Experimental results of the positron annihilation 2#gamma#-correlations and the positron annihilation rates in ReO_3 are discussed based on the positron wavefunction. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The heat transfer augmentation effect by the unsteady heat conduction between the particles and heat transfer surface is one of the main factors, causing the heat transfer augmentation around the stagnation point in the gas-solid two-phase impinging jet flow. By separating and evaluating that effect, material influence on it was studied of particles and heat transfer surface, together with change by the jet flow condition. That effect enlarged with enlarging in heat capacity, multiplied by the heat conduction coefficient, of both the particles and heat transfer surface, and if both of them were constant in material combination, was dominated by the contact frequency of particles per unit time. Therefore in case of lading solid particles, equal in weight, that effect enlarges with diminishing in particle diameter. Such a heat transfer augmentation mechanism model is universally applicable to the data by Yoshida et al., using ...

CERN Document Server

The hyperfine interactions at the uranium site in the antiferromagnetic USb2 compound were calculated within the density functional theory (DFT) employing augmented plane wave plus local orbital (APW+lo) method. We investigated the dependence of the nuclear quadruple interaction to the magnetic structure in USb2 compound. The result shows that the 5f-electrons have the tendency to be hybridized with the conduction electrons.

Energy Technology Data Exchange (ETDEWEB)

Concerning heat transfer augmentation of an axisymmetric impinging jet using a perforated plate set, the bore of the hole in the plate for local and averge heat transfer rate, pitch, and effect of the distance between perforated plate and target plate were examined. Heat transfer augmentation was examined under the condition of 0.063 /ge/d/D /ge/0.200, 1.25 /ge/p/d /ge/4.00, Re is approximately equal to 18000, (where d is the bore of the hole in the plate, D is the axisymmetric nozzle outlet bore, p is the pitch of the perforated plate, and Re is the jet Reynolds number). The findings are as follows; The velocity of the small jet after passing the perforated plate is reduced, and resistance to disturbance is remarkably large. The small jet which is not at the center hole extends to the outside of the plate. The heat transfer rate at a stagnation point is high when the target plate is placed in the jet potential core area and that ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m{sup 2} generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat flux up to 12 MW/m{sup 2} could be ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer has emerged as a leading-edge technology supporting the rapid pace of developments in science and engineering ranging from energy production to electronic cooling. Subjects covered at the 6th UK National Conference on heat transfer held at Edinburgh from 15-16 September 1999 include: convection; boiling and evaporation; condensation; numerical techniques; heat exchangers; radiation and combustion; conduction; two-phase flow and heat transfer augmentation. Fifteen of the papers are abstracted here.

International Nuclear Information System (INIS)

This book presents the papers given at a conference on two-phase flow. Topics considered at the conference included the thermal hydraulics of a feedwater pipe breakage, pressure losses, measurement of void fraction in a rod bundle, laminar filmwise condensation, natural circulation, flow models, bubble dynamics, cavitation, water hammer, and heat transfer augmentation.

Energy Technology Data Exchange (ETDEWEB)

This research investigates experimentally mixed convection and heat transfer augmentation by forced jets in a large enclosure, at conditions simulating those of actual passive containment cooling systems and scales approaching those of actual containment buildings or compartments. The experiment was designed to measure the key parameters governing the heat transfer augmentation by forced jets and investigate the effects of geometric factors, including the jet diameter, jet injection orientation, interior structures, and enclosure aspect ratio. The tests cover a variety of injection modes leading to flow configurations of interest that contribute to reveal the nature of mixing and stratification phenomena in the containment under accident conditions of interest. The heat transfer of mixed convection can be predicted to be controlled by jet Archimedes number and geometric factors. Using a combining rule for mixed convection and appropriate forced ...

UK PubMed Central (United Kingdom)

To determine if the enhanced glycemic response to epinephrine in patients with insulin-dependent diabetes mellitus (IDDM) is the result of increased adrenergic sensitivity per se, increased glucagon...Full Text Available

International Nuclear Information System (INIS)

This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic steam induced by ultrasonics is a major contribution to heat transfer augmentation. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper describes the research and development activities in three areas of radiation processing, namely: food irradiation, medical product sterilization and wood plastic combination. Plans and efforts exerted to acquire a larger gamma source to augment our present 5,000 curie source are discussed. Cost estimates for a radiation facility are presented on the basis of the market potential of food irradiation and medical product sterilization. Existing local industries that can benefit from the adaptation of irradiation technology in their processing requirements are described.

International Nuclear Information System (INIS)

To calculate the energy band structures in semiconductors using the relativistic augmented plane wave method, atomic potential and charge density are needed, which are calculated by self-consistent method. Wave function for one electron is determined by solving the Dirac equation with the Hartree-Fock equation based on the slater's exchange potential. The results of calculation for Cu"+"1 are given. (Author).

CERN Document Server

We present an approach to automatically generate interfaces supporting personalized interaction with digital libraries; these interfaces augment the user-DL dialog by empowering the user to (optionally) supply out-of-turn information during an interaction, flatten or restructure the dialog, and enquire about dialog options. Interfaces generated using this approach for CITIDEL are described.

International Nuclear Information System (INIS)

This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.

Energy Technology Data Exchange (ETDEWEB)

We have investigated tailoring damage effects of explosive devices by addition of unconventional materials, specifically combustible metals. Initial small-scale as well as full-scale testing has been performed. The explosives functioned to disperse and ignite these materials. Incendiary, enhanced-blast, and fragment-damage effect have been identified. These types of effects can be used to extend the damage done to hardened facilities. In other cases it is desirable to disable the target with minimal collateral damage. Use of unconventional materials allows the capability to tailor the damage and effects of explosive devices for these and other applications. Current work includes testing of an incendiary warhead for a penetrator.

International Nuclear Information System (INIS)

Field Programmable Gate Arrays (FPGAs) are being used in space applications because of attractive attributes: good density, moderate speed, low cost, and quick turn-around time. However, these devices are susceptible to Single Event Upsets (SEUs). An approach using triple modular redundancy (TMR) and feedback was developed for flip-flop hardening in these devices. Test data showed excellent results for this circuit topology. Total dose and Single Event Effect (SEE) testing have been performed on recently released technologies. Failures are analyzed and test methodology is discussed.

Energy Technology Data Exchange (ETDEWEB)

Recently, organic semiconducting materials have gained a broad interest due to their potential for organic electronic devices such as organic light emitting diode (OLED), organic photovoltaic devices and organic field-effect transistors (OFETs). Optical properties of organic semiconducting materials are important for practical application. For example, the power conversion efficiency of organic photovoltaic devices is mainly affected by absorption properties of organic materials. Proton irradiation is one of the efficient methods to change the optical properties of organic materials. In this paper, we investigate the changes of optical properties of various polymers using the proton irradiation.

International Nuclear Information System (INIS)

Experimentally it is shown that a movable grounded metallic plate placed inside a multi-dipole magnetic cage can vary the diffused plasma parameters such as density, plasma potential and electron temperature. Plasma is solely produced in the source section of a double plasma device by a dc hot filament discharge and a low-density plasma is produced in the target section by local ionization of neutral gas by the high energetic electrons coming from the source section. A grounded movable stainless steel plate is inserted in the target section of the device. The floating potential of the plate also changes depending on the position of the plate inside the magnetic cage.

International Nuclear Information System (INIS)

The feasibility of a high-energy electron cooling device has been studied through tests on a prototype of the electron device. The apparatus consists of a pulsed ((20-60) keV, 2#mu#s) electron gun, a drift region 1 m long and of a depressed collector for recovering the electron energy. Tests on beam optics and energy recovery have been performed, a high-energy recovery efficiency has been attained. Experimental results are discussed in this paper.

International Nuclear Information System (INIS)

Two new identical insertion devices have been designed for the Daresbury SRS. They are 2T permanent-magnet multipole wigglers that will provide high flux in the X-ray region. This paper describes the magnetic and mechanical design of the arrays of steel pole pieces and permanent-magnet blocks. Also given is the engineering design of the support structure that will cope with the very large forces present while maintaining high levels of precision in gap setting and parallelism. The engineering design has been fully assessed using finite-element techniques to predict the deflections of critical parts of the structure. These two devices are due to be installed into the SRS by the end of 1998.

International Nuclear Information System (INIS)

A novel device called the gas expansion model (GEM) is being developed at the Hanford Engineering Development Laboratory for testing in the 400-MW(th) fast flux test facility (FFTF) reactor. Incorporation of the GEM into liquid-metal reactor designs is intended to measurably contribute to the achievement of inherent safety, by allowing the reactor to passively shut down even in the extremely remote (hypothetical) event of an unprotected (no scram) loss-of-flow accident. The purpose of this paper is to describe the GEM and present predictive analyses of the effectiveness of the device during unprotected loss-of-flow experiments in the FFTF.

UK PubMed Central (United Kingdom)

BackgroundThe routine removal of orthopaedic fixation devices after fracture healing remains an issue of debate. There are no evidence-based guidelines on this matter, and little...Full Text Available

Science.gov (United States)

A silicon solar cell assembly comprising a large, thin silicon solar cell bonded to a metal mount for use when there exists a mismatch in the thermal expansivities of the device and the mount.

Science.gov (United States)

It is well known that the growth of purple plague is tempera- ture dependent. in Figure 2 which shows the progressive growth of purple ...

Science.gov (United States)

... lasers, model switched optical memory elements ... Optical RS flip flop, Acousto-optic switches. ... FLOP CIRCUITS, OPTICAL SWITCHING, NOR GATES ...

Energy Technology Data Exchange (ETDEWEB)

Wave energy device teams have identified three varieties of air turbine as potentially applicable to wave energy devices. These are: conventional axial turbines; Wells, or self-rectifying, axial turbines and Francis turbines. This report examines the constructional requirements of these devices with regard to mechanical, environmental and manufacturing considerations. It is concluded that the major benefit of optimum material selection will be reduced manufacturing costs rather than enhanced turbine performance. A methodology of material selection has been established and candidate materials have been listed for the major components of each turbine type. Comparative costs for alternative materials are included, from which significant, potential economies have been identified. Recommendations are made aimed at achieving optimum material usage in the proposed turbines.

Science.gov (United States)

... silicon oxide (BSO), bismuth germanium oxide (BGO), and bismuth titanium oxide (BTO). These crystals are electro-optic, optically active, ...

Energy Technology Data Exchange (ETDEWEB)

Pd/n-Si and Pd/n-GaAs devices have been irradiated from high energy ({approx}100 MeV) heavy ions of Au{sup 7+} (gold) and Si{sup 7+} (silicon) to study the irradiation effects in these junction devices on semiconductor substrates. The devices have been characterized from I-V and C-V studies for electronic flow characterization. It has been found that the devices become high resistive on the irradiation and the substrates change the conductivity type from n- to p- on the irradiation of fluence of {approx}10{sup 12}-10{sup 13} ions/cm{sup 2}. The change in conductivity type has been understood as a result of creation of deep acceptors on the irradiation.

International Nuclear Information System (INIS)

The methods of superconducting device fabrication by lithography and multilevel processing usually require a number of processing steps with lithographic resolution and alignment adequate for the scale of the device be fabricated. As an alternative, the focused ion beam (FIB) microscope is increasingly being used directly to fabricate devices. A major advantage of using a FIB compared to other lithography methods is its flexibility and high resolution. It allows in-situ, milling (#propor to#5 nm at a beam current of 1 pA) to a variety of depths, and imaging (2 nm) of the sample. In this paper we describe our development of junction fabrication techniques using the FIB and their application in creating a range of potential sensor devices and quantum electronics applications. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Energy Technology Data Exchange (ETDEWEB)

A compact and supersensitive device that can rapidly detect minute trace vapors from concealed explosives has been developed by scientists at Oak Ridge National Laboratory (ORNL). The new explosives sensor can detect and chemically identify organic nitrogen-oxygen compounds which are the building blocks of explosives such as TNT, plastiques, and nitroglycerine. The device could be used to scan persons entering airport terminals, nuclear power plants, defense installations, or other sensitive locations, providing greater security against potential terrorism. This device works on a glow discharge principle, and is more specifically called an ''Atmospheric Sampling Glow Discharge Ionization'' (ASGDI) source. The new detector is a highly automated, miniaturized version of research mass spectrometers widely used to trace constituents of chemical mixtures. Detail of this ...

Science.gov (United States)

Improved quantum-cascade lasers. (QCLs) are being developed as electri- ... These devices would supplant gas lasers as far-infrared sources. ...

International Nuclear Information System (INIS)

This paper reviews various techniques to harden Charged Coupled Device (CCD) sensors and the results after irradiation of three Thomson n buried channel CCDs having a different degree of hardening. It describes the major irradiation effects on CCD performances and it makes a comparison of the results between the different hardening levels. It shows good results on dark voltage after ionizing radiation for TH 7863M device hardened both by design and by operating conditions (MPP mode) with respect to the standard device TH 7863A. The irradiations were performed with "6"0Co or X-ray (10 keV) sources on devices in operating mode. (author). 3 refs., 8 figs.

Science.gov (United States)

... with the ability to capture imagery in raw 24-bit format, combined with large memory storage devices enable high resolution imagery to be captured ...

International Nuclear Information System (INIS)

Fusion device produces high-level neutrons and #gamma#-rays, which would hazard the safety of the public and workers if the doses would be higher than the regulatory limits because of leakage from the bio-shielding and skyshine. It is essential to monitor the radiation doses in the workshop and the enumerative around fusion devices. A radiation monitoring system (RMS) for full (near and far) areas around a nuclear fusion device has been designed and developed, which can achieve the monitoring and controlling of radiation doses in the workshop area by using the Controller Area Network (CAN), in the institution area by using the Bluetooth Ad hoc network based on a new tree topology formation and routing protocol and in a long range environment by using the General Packet Radio Service (GPRS) network. (authors)

International Nuclear Information System (INIS)

Mechanical testing of controlled-purity Ni-xCr-9Fe-yC alloys at 360 C revealed an environmental enhancement in IG cracking and time-dependent deformation in high purity and primary water over that exhibited in argon. Dimples on the IG facets indicate a creep void nucleation and growth failure mode. IG cracking was primarily located at the interior of the specimen and not necessarily linked to direct contact with the environment. Controlled potential CERT experiments showed increases in IG cracking as the applied potential decreased, suggesting that hydrogen is detrimental to the mechanical properties. It is proposed that the environment, through the presence of hydrogen, enhances IG cracking by enhancing the matrix dislocation mobility. This is based on observations that dislocation-controlled creep controls the IG cracking of controlled-purity Ni-xCr-9Fe-yC in argon at 360 C and grain boundary cavitation and sliding results that show the environmental enhancement ...

Energy Technology Data Exchange (ETDEWEB)

Restructured power markets require concepts not only for extending the lifetime of existing plants, but also concepts for reducing the life-cycle costs of existing older steam power plants in order to remain competitive with the most modern and advanced power generation technology such as combined cycle power plants. Out of the broad range of methods to extend service life and increase availability, and to increase power output and efficiency, this paper focuses on full repowering. Full repowering replaces the old fired boiler with gas turbine(s) and heat-recovery steam generators (HRSG) as heat input to the existing bottoming cycle and reuses the steam turbine (ST) condenser and further balance of plant (BOP) equipment. The potential offered by this concept is demonstrated. Repowering and modernization projects are executed if they result in economic benefits for the operator. Investment decisions need to be prepared based on an estimate or proof of an adequate return on investment ...

Energy Technology Data Exchange (ETDEWEB)

A massively-parallel ab initio computer code, which uses Gaussian bases, pseudopotentials, and the local density approximation, permits the study of transition-metal systems with literally hundreds of atoms. We present total energies and relaxed geometries for Ru, Pd, and Ag clusters with N = 55, 135, and 140 atoms; we also used the DMOL code to study 13-atom Pd and Cu clusters, with and without hydrogen. The N = 55 and 135 clusters were chosen because of simultaneous cubo-octahedral (fcc) and icosahedral (icos) sub-shell closings, and we find icos geometries are preferred. Remarkably large compressions of the central atoms are observed for the icos structures (up to 6% compared with bulk interatomic spacings), while small core compressions ({approx} 1 %) are found for the fcc geometry. In contrast, large surface compressive relaxations are found for the fcc clusters ({approx} 2-3% in average nearest neighbor spacing), while the icos surface displays small compressions ({approx} 1%). ...

International Nuclear Information System (INIS)

The method of treatment of uteral cancer by the brake irradiation of 25 MeV betatrone using original devices which promote forming therapeutic figured bunches is presented. The binding of the protective blocks with a special adjusting frame within the aperture of the diaphragm provided for low relative entering dose which is the advantage of high energy irradiation bunch. The use of the forming devices makes it possible to practice individual treatment and decrease the levels of irradiation doses for intact organs and tissues.

Energy Technology Data Exchange (ETDEWEB)

We demonstrate a two-dimensional device simulator for MOSFET structures that incorporates models for defect distributions and show predicted effects on device switching performance for various spatial distributions of defects in amorphous and polycrystalline silicon.

Science.gov (United States)

The experimental device for generation of undulator radiation in terahertz wavelength region by use of undulator with ferromagnets is created. The device is based on a beam of a microtron with the energy 7.5 MeV. The radiation wavelength is 200 mu. Registered spontaneous radiation has a power 10{sup -6} W at a current of a beam 2 mA in a pulse. With the optical resonator, in a mode, the amplification of 6% is received, that in sometimes is more than the expected value. This effect is explained as a result of partial coherence of radiation.

International Nuclear Information System (INIS)

The seawater in the intake structure flows into the large pump to with draw excess heat from the turbine steam condenser. In the intake structure of a nuclear power plant, undesirable pump operating characteristics such as vortices, impeller damages and non-uniform pump-approach flow around the pump bells take place frequently due to poorly-arranged intake geometry. In this study, physical modeling test was performed to predict the hydraulic phenomenon, and proposed flow control devices.

Energy Technology Data Exchange (ETDEWEB)

The NREL Sensitized Solar Cell (SSC) Core Program supports the Solar America Initiative by: (1) targeting new devices and processes for commercialization by 2015 that are less expensive, more efficient, highly reliable, and environmentally benign; (2) collaborating with DOE OS/BES to conduct basic research targeting breakthroughs in key areas, such as ultra-high efficiency and/or ultra-low cost materials and devices.

International Nuclear Information System (INIS)

An Ottawa-based company, ECS-Power Systems Inc., has successfully completed a series of tests on an innovative device called a hydrodynamic port (HDP), which makes it possible to automatically initiate and maintain emergency cooling of a nuclear reactor core by natural processes, without relying in any way on human intervention, instrumentation, electric power, valves or moving parts of any kind.