Energy Technology Data Exchange (ETDEWEB)

To investigate the influence of equal channel angular pressing on the microstructure and texture of the magnesium alloy AZ31, electron backscattering diffraction and well as neutron diffraction experiments were carried out. Through these experiments it was possible to trace the microstructure and texture evolution with strain accumulated with the increasing number of equal channel angular pressing passes. It was further demonstrated by subsequent compression tests that the microstructural changes produced by equal channel angular pressing have a beneficial effect on both the compressive strength and ductility of AZ31. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Friction stir welding of dissimilar formed Mg alloys(AZ31/AZ91) was successfully carried out at the limited welding conditions. In a sound joint, SZ was mainly consisted of AZ31 Mg alloy which was located the retreating side. Dynamic recrystallization and grain growth occurred and {beta} intermetallic compounds of AZ 91 Mg alloy was not observed in SZ. BM had a higher hardness than that of the weld zone. The fracture location was not weld zone but BM of the AZ91 Mg alloy in tensile test. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Superconducting MgB{sub 2} samples were prepared by the sintering of a mixture of fine Mg (or Mg alloy) powder produced by gas-atomization and B powder. The single MgB{sub 2} phase with a superconducting onset temperature of 38 K was obtained by sintering at 1073 K for the pure Mg or AZ31 alloy powders. In the case of AZ31, the superconducting MgB{sub 2} was obtained by sintering at a low temperature of 873 K for 50 h although a long sintering time of 100 h is needed to obtain a single MgB{sub 2} phase for Mg powder. This indicates that the AZ31 alloy enhances a formation rate of superconducting MgB{sub 2} at the low temperature through the formation of the partial melting ...

Energy Technology Data Exchange (ETDEWEB)

Solid recycling of AZ31 Mg alloy with vapor deposition coating layer of high purity Mg was evaluated. In the open die forging experiments, two AZ31 Mg alloy specimens with the pure Mg layer were sufficiently bonded by forging at 673 K. Furthermore, the Al and Zn of the AZ31 substrate diffused up to the center of the pure Mg layer. By the theoretical analysis, it is suggested that the grain boundary diffusion enhanced by grain refinement due to hot forging contributes to the solid state bonding of the specimens. Also, the solid recycled specimen was fabricated from the AZ31 Mg substrate with pure Mg layer by hot extrusion at 673 K. The solid recycled specimen showed almost the ...

British Library Electronic Table of Contents (United Kingdom)

Commercial rolled magnesium sheets of alloys AZ31 (Mg-3 mass%Al-1 mass%Zn) and ZE10 (Mg-1 mass% Zn-<1 mass% Rare Earths) in O-temper condition were used for blanking experiments near room temperature. A serrated fracture surface can be observed in case of AZ31 but not in case of ZE10. During the shearing process of the AZ31 sheet, many micro cracks parallel to the sheet plane are generated in the shearing zone. These micro cracks lead to the formation of loose particles during the shearing operation, which interfere with further processing of the part and incur additional costs by increasing the scrap rate. It is found that the strong basal texture of this alloy is an important reason for the generation of such serrated cracks. In this paper a new method of selective texture modification i...

Energy Technology Data Exchange (ETDEWEB)

The present paper describes the development of ultra-fine grains on the surface of AZ31 alloys caused by hydrogenation and dehydrogenation treatment, so-called HDDR process. Upon hydrogenation process, disproportionation reaction occurred in forming of MgH{sub 2}, Mg{sub 0.42}Al{sub 0.58}, and Al phases. In the following desorption process, the three phases were re-solved into the AZ31 alloy. As a result of the HDDR phenomena, the grain size of AZ31 alloy powders was reduced down to about 100 nm after the heat treatment at 350 C under a hydrogen pressure of 7 MPa for 24 h. The grain size tended to be increased with increasing process temperatures. In addition, the HDDR process was also applied to AZ31 alloy plates. By the HDDR process at 450 C, the grain size was reduced to less ...

Energy Technology Data Exchange (ETDEWEB)

High temperature deformation behavior of AZ31 Mg alloy was investigated in this study on the basis of a processing map ({epsilon} {approx} 0.6). To construct a processing map, compression tests were carried out at various temperatures and strain rates. Two regions of high deformation efficiency ({eta}) were identified as: (1) a dynamic recrystallization (DRX) domain at 250 C and 1/s and (2) a superplasticity domain at 450 C and 10{sup -4}/s. The average grain size observed in the DRX region was considerably smaller (2.9{mu}m) than in any other region. In the superplastic condition, tensile elongation to failure approached to 1040%. At the high Z regions, flow softening occurred resulting from the dynamic recrystallization but below 10{sup 10} of Z value, flow hardening occurred due to the grain growth. Possible deformation mechanisms operating at high temperature were discussed in relation to the activation energy. A ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The microstructural evolution of a AZ31 Mg alloy during hot rolling has been investigated using optical microscopy and texture (macro and micro) analysis as the main characterization tools. In particular, the differences between the microstructure obtained by unidirectional rolling (UR) and cross rolling (CR) are studied. Significant twinning activity is observed in both cases. Additionally, after cross rolling, a rather heterogeneous microstructure develops, with scattered regions populated by very fine grains. The strong basal fiber texture of the as-received material remains present after both hot rolling schemes. The impossibility to obtain accurate EBSD measurements within the twinned regions suggests that significant localized deformation takes place in those areas. Thus, these regions become preferential sites for the onset of recrystallization due to the increase in the local strain energy. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)

Energy Technology Data Exchange (ETDEWEB)

AZ31 Mg alloy samples were extruded by an equal channel angular extrusion (ECAE) process and subsequently annealed to obtain fine-grained material with a low dislocation density. Tensile tests at room temperature exhibited an apparent steady-state deformation region and a large tensile elongation of 47%. The deformed microstructure at an elongation of 2% indicated a substantial cross-slip to nonbasal planes possibly induced by grain-boundary compatibility effects. The nonbasal segments of dislocations were found to consist of 40% of the total dislocation density at a yield anisotropy factor of only 1.1 instead of an expected value of 100 from single-crystal experiments. (orig.)

International Nuclear Information System (INIS)

Microstructure and properties of a Mg AZ31B laser beam weld without filler are studied using electron microscopy, X-ray diffraction and mechanical tests. The microstructure of the weld is characterized by a narrow heat affected zone, columnar grains and precipitate coarsening in the fusion zone. Texture in the fusion zone is significantly different from the texture of the base material. The residual stress distribution observed is similar at the top and the bottom of the weld, maximum tensile residual stress values are observed in the fusion zone. Tensile tests reveal differences in the mechanical behavior of the fusion zone and the parent material, which can be related to the differences of texture and the resulting deformation mechanisms.

International Nuclear Information System (INIS)

The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic ...

Energy Technology Data Exchange (ETDEWEB)

The microstructures and mechanical properties of the AZ31 Mg tubes fabricated by one-pass forward piercing tube extrusion operated at 250-400 C and 10{sup -2}-10{sup 0} s{sup -1} are examined. The grain size is refined from the initial {proportional_to}75 {mu}m grain size down to {proportional_to}1.5 {mu}m. The room temperature tensile elongation along the extrusion direction also increases from {proportional_to}13% for the as-received billet up to 51%. The highest superplastic elongation of 610% was obtained as tensile loaded at 300 C and 2 x 10{sup -4} s{sup -1}, and high strain rate superplasticity of 406% and 502% was achieved at 300 C and 400 C with a high strain rate of 1 x 10{sup -2} s{sup -1}. Preliminary hydroforming or tube bulging at room temperature has demonstrated the feasibility. Hydroforming at elevated temperature of 200 C or above should exhibit much more promising results, utilizing the capability of LTSP ...

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl ...

International Nuclear Information System (INIS)

The in-situ measurement of a crystallographic texture is a special type of a non-destructive measurement, which need special equipments. Due to the high photon flux and the excellent brilliance high energetic synchrotron radiations are a fantastic tool particular in fast experimentation. Moreover, a high penetration power allows the investigation of standard tensile sample of the DIN-norm. A loading device with a power up to 20 kN was installed at the hard wiggler beamline BW5 (HASYLAB-DESY) to perform in-situ strain and in-situ texture analysis. Using 100keV X-rays one gets short wavelength so that a 2D image-plate detector offers a wide range of diffraction pattern within the first 10 degree in 2 theta. Thermal neutron is another radiation with a high penetration power, which is the standard method for global texture analysis of bulk samples. As an example rectangular extruded Mg- Az31 was investigated by an in-situ. ...

Energy Technology Data Exchange (ETDEWEB)

Deformation mechanisms were investigated in fine-grain (d=7 {mu}m) AZ31 Mg alloy in order to understand their excellent room-temperature ductility. Dislocation cross slip from basal to non-basal planes was found to occur easily at room temperature at a plastic anisotropy factor of only 1.5 instead of several tens to 100 expected from the single crystal CRSS data. Enhanced grain-boundary sliding (GBS) was also found to occur at room temperature. The contribution of GBS strain was found to be approximately 8% of total strain. The enhanced activity of non-basal dislocation slip and GBS was attributed to grain-boundary compatibility effects. Moreover, dynamic recovery was found to occur during deformation at room temperature associated with the formation of recovery twins and small-angle grain boundaries. The occurrence of these deformation mechanisms at room temperature was considered to be a major reason for an excellent ...

Energy Technology Data Exchange (ETDEWEB)

The effects of carbon inoculation by C{sub 2}Cl{sub 6} addition were investigated using commercial AZ31 magnesium alloy. The additions of C{sub 2}Cl{sub 6} to AZ31 magnesium alloy significantly reduce the grain size from 280 {mu}m to about 120 {mu}m and the tensile properties are also increased due to grain refinement. EPMA analysis shows that Al-C-O compounds are formed in the castings which are considered to function as nucleants. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Using commercial AZ31 magnesium alloy sheets, we produced a foamable preform sheet containing titanium hydride (TiH{sub 2}) powder through diffusion-bonding and hot-rolling of four cycles. Heating the preform sheets in Ar atmosphere, we obtained closed-cell magnesium alloy foams with various porosities. The foamed specimen at 883 K showed the maximum porosities of 77%. (orig.)

British Library Electronic Table of Contents (United Kingdom)

In the present study, new light weight nano-composites (AZ31B-3.3Al2O3-Cu) based on magnesium alloy AZ31B are developed using disintegrated melt deposition technique. Microstructural characterization studies revealed grain refinement and significant increase in amount of second phases as a result of increasing presence of copper. All the samples exhibited minimal porosity and good matrix-second phase interfacial integrity. The results also showed that addition of both nano-Al2O3 and Cu led to a simultaneous improvement in 0.2% yield compressive strength (0.2%YCS), ultimate compressive strength (UCS) and work of fracture (WoF) of the AZ31B magnesium alloy while failure strain was marginally affected. The results of this study clearly illustrate the capability of AZ31B-Al2O3-Cu formulations ...

International Nuclear Information System (INIS)

One of the major concerns during high speed welding of magnesium alloys is the presence of porosity in the weld metal that can deteriorate mechanical properties. This study seeks to analyze the presence method and quantity of pore during hybrid laser-tungsten inert gas arc (TIG) welding of magnesium alloy AZ31B by radiography, optical microscopy and electron probe microanalysis (EMPA). At the same time, it identifies both the mechanism of pore formation and a remedy for this problem. The experimental results indicate that lacking of shielding gas for laser beam is the dominant cause of macroporosity formation during the hybrid of laser-TIG welding of magnesium Alloys AZ31B plate, and hydrogen is not main cause to form large pores. A favorable weld without porosity can be obtained by appending lateral shielding gas for laser beam.

Energy Technology Data Exchange (ETDEWEB)

A press formability of magnesium alloy sheet cannot be evaluated by only general characteristics in tensile test; tensile strength, elongation n-value and r-value. For example, AZ31-alloy elongates about 20% in room temperature but breaks easily at shallow stage in deep drawing, which is caused by little local elongation (local necking). Crystallographic restriction of slip deformation in this alloy produces high strength, which almost equal to macroscopic fracture strength. In press forming, the bending under high tension requires a large deformability. A great difference in the deformability between AZ31 magnesium alloy and a strain hardened A1100 Aluminum (only 5% in elongation) is shown by static bending test with V-notch. In a rolled plate of AZ31, a crack is produced by stress concentration and propagates with reduced load at all testing temperature up to ...

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The superplastic characteristics and diffusion bonding behaviors were investigated in commercial 7475 aluminum alloy and AZ31 magnesium alloy sheets. In this study, the presently used materials behaved in a superplastic manner at {proportional_to} 773 K (7475Al) and {proportional_to} 523 K (AZ31). Then, by the theoretical relationship between pressure and time, these materials were successfully diffusion bonded at the superplastic temperatures. The bonding strength was more than 65 MPa. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, numerical modelling ...

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A new technique has been developed for improving corrosion resistance on magnesium alloys. Specimens of AZ31 magnesium alloy were dipped into molten salt of NaBF{sub 4} at 723 K for various times, and then cooled, rinsed with water, and dried in air. Corrosion resistance in the surface treated specimens was evaluated by salt immersion test using 1% NaCl solution as a time for occurring filiform corrosion. On an un-treated AZ31 alloy, the time for starting the filiform corrosion was about 1.2 ks, while on the surface treated specimen, the time was prolonged into about 1300 ks. Moreover, the surface treated specimen showed corrosion resistance in low pH solutions, such as 1% HNO{sub 3} and HCl solutions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Dynamic development of new grain boundaries was studied in compression of a magnesium alloy AZ31 with initial grain sizes (D{sub 0}) of 22 {mu}m and 90 {mu}m at a temperature of 673 K. Kink bands are evolved near corrugated grain boundaries and in grain interiors at low strains accompanied with new fine grains. Kink bands are developed often perpendicular to the basal plane. The boundary misorientation of kink band as well as the volume fraction of new grains increases rapidly with increasing strain and approaches a saturation value in high strain. New fine grains are developed faster with decrease in the D{sub 0}. It is concluded that new grain evolution is controlled by a deformation-induced continuous reaction, i.e. continuous dynamic recrystallization (DRX). (orig.)

Energy Technology Data Exchange (ETDEWEB)

Plastic formability of cast magnesium alloy that were hot rolled after roll strip casting was investigated to ascertain the feasibility of semi-solid strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Two extruded magnesium alloys, AZ31 and AZ61 were selected to evaluate the influence of process parameters on the material forgeability. The processing parameters considered for forging magnesium alloys were: compression load in the range 55 KN to 60 KN and forging temperature, in the range of ambient temperature to 300 C. Uniaxial compression tests were conducted to establish the strain-temperature relationship. The influences of process parameters on the microstructure were also evaluated. (orig.)

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron ...

Energy Technology Data Exchange (ETDEWEB)

Increase usage of magnesium components in the portable electronics industries has propelled considerable research interest on the development of magnesium forging. There have been some studies done in the area of sheet metal forming and forging of axis-symmetrical parts of magnesium alloys but there are very little work done on the plane strain backward extrusion of magnesium alloy. This paper deals with the analysis of plane strain extrusion of magnesium alloy, AZ31, using numerical modeling at different extrusion conditions of temperatures and friction coefficients. A commercially available finite element package, ANSYS/LSDYNA, was used in the finite element analysis. FE simulated results, material deformation, punch force and stress/strain distributions, were compared with actual experimental data. From the numerical analysis, a decrease in forging temperature from 300 C to 250 C will lead to a moderate increase in forming resistance. The ...

International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion solutions upon the coatings formation was ...

Energy Technology Data Exchange (ETDEWEB)

The deformation behavior and structure changes of magnesium alloy AZ31 were studied in compression at temperatures ranging from 523 K to 673 K and at a strain rate of 3 x 10{sup -3} s{sup -1}. They depend sensitively on deformation temperature. At high temperatures, grain fragmentation takes place due to frequent formation of kink bands initially at corrugated grain boundaries and then in grain interiors, followed by full development of new grains in high strain. At lower temperatures, in contrast, twinning takes place in rather coarse grains and kink bands are formed mainly in finer original ones in low strain. It is concluded that new grain evolution can be controlled by a deformation-induced continuous reaction resulting in grain fragmentation by kink bands, i.e. continuous dynamic recrystallization (cDRX). The latter is discussed comparing with conventional, i.e. discontinuous, DRX. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was also influenced by the test orientation. Metallographic studies ...

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are compared.

Energy Technology Data Exchange (ETDEWEB)

This paper deals with an experimental study of ultra-precision diamond cutting of magnesium alloy (AZ31). In order to investigate the machinability such as the cutting force and the surface integrity and understand the problems in a micro cutting, the experiments on the diamond cutting of magnesium alloy and pure aluminum with an ultra-precision turning machine has been carried out. The machinability of magnesium alloy was compared with that of pure aluminum and discussed. Consequently, both the thrust force component and the surface roughness obtained by cutting of magnesium alloy became larger than that of pure aluminum. It was also found that the inclusions or the defects in the work material caused to generate the scratches on the finished surface and influenced the integrity of mirror surface. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, r-values and their relation to the texture. This correlation between microstructure ...

Energy Technology Data Exchange (ETDEWEB)

The warm caliber rolling was experimented using the AZ31 magnesium alloy round bar of 20 mm in diameter machined from cast ingot materials. In warm caliber rolling in final size of 10 mm in diameter at 623 K via 8passes, each width-spreading, the change of each microstructure, X-ray analysis of final texture and final mechanical properties were investigated. Microstructure, texture and mechanical properties of warm caliber rolled round bar at 473 K via latter 4passes were compared with those at 623 K consistently. Obtained results are as follows: (1) The width-spreading in caliber rolling of round bar is relatively large, compared with that in flat rolling of the flat bar. The largeness of width-spreading of round bar makes the shape control of cross section difficult, and causes the cracks around the free surface. (2) Finer microstructure and inclined c axis of hexagonal lattice of 10 degrees to vertical direction of the rolled surface are ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

Machines and structures, such as automobiles are usually subjected to biaxial or three-axial stresses instead of uniaxial stress. However, research on a fatigue failure under multi-axial stress has not been fully presented because such experiments are difficult. To solve this problem, we developed the servo biaxial fatigue-testing machine. In this research, we performed the biaxial fatigue tests of a magnesium alloy in order to clarify the effects from different heat treatments. Magnesium alloy is the lightest in weight among metal materials for structural use. The fatigue characteristics of a magnesium alloy are indispensable in order to create the design which ensures the reliability and the safety of the vehicles especially in long-distance run. The main conclusions are summarized as follows; (1) The mechanical property of magnesium alloy AZ31B falls by heat treatment at low temperature. (2) The crack progress speed becomes quick by the fall ...

Energy Technology Data Exchange (ETDEWEB)

The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. The experimental ...

Science.gov (United States)

It is well known that one of the main advantages of the high speed forming (HSF) processes is the improvement in the forming limits of the used materials.Using the Electromagnetic Forming (EMF) technology two materials have been tested with different mechanical and physical properties: the AA5754 aluminium and the AZ31B magnesium alloys.The EMF process principle can be described as follows: A significant amount of electrical energy is stored in a bank of capacitors which are suddenly discharged releasing all the stored energy. This electric discharge runs through a coil which generates an intense transient magnetic field. At the same time transient Eddy currents are induced in the electrically conductive part placed some millimetres far from the coil. Another intense magnetic field is generated due to those Eddy currents but on the opposite direction as the one generated by the coil. A big magnetic repulsion force is created between the part ...

Science.gov (United States)

... 1, CLONAZEPAM ORALLY DISINTEGRATING TABLETS, 0.125 MG, 0.25 MG, 0.5 MG, 1 MG, AND 2 MG, KALI LABORATORIES, INC. KLONOPIN RAPIDLY DISINTEGRATING TABLETS, 8/3/2005 ...

British Library Electronic Table of Contents (United Kingdom)

Objectives: Evaluate the effect of diet, physical exercise, and a daily oral intake of a soy isoflavones extract (Fisiogen) contained 200mg of Glycine max, which corresponded to 80mg of isoflavone (60.8mg of genistein, 16mg of daidzein and 3.2mg of glicitein) on leptin and other adipokines plasma levels in healthy obese postmenopausal women. Methods: A multicentric randomized longitudinal prospective cohort study was conducted in a sample of 87 healthy obese postmenopausal women. Patients were randomly assigned to a 1200kcal diet and exercise group (control group) or a group of 1200kcal diet, exercise, and daily oral intake of daily oral intake of a soy isoflavones extract (Fisiogen) contained 200mg of Glycine max, which corresponded to 80mg of isoflavone (60.8mg of genistein, 16mg of daid...

International Nuclear Information System (INIS)

The rare earth metal rich compounds RE4NiMg (RE=Y, Pr-Nd, Sm, Gd-Tm, Lu) were synthesized from the elements in sealed tantalum tubes in an induction furnace. All compounds were investigated by X-ray diffraction on powders and single crystals: Gd4RhIn type, space group F4-bar 3m, Z=16, a=1367.6(2) pm for Y4NiMg, a=1403.7(3) pm for Pr4NiMg, a=1400.7(1) pm for Nd4NiMg, a=1386.5(2) pm for Sm4NiMg, a=1376.1(2) pm for Gd4NiMg, a=1362.1(1) pm for Tb4NiMg, a=1355.1(2) pm for Dy4NiMg, a=1355.2(1) pm for Ho4NiMg, a=1354.3(2) pm for Er4NiMg, a=1342.9(3) pm for Tm4NiMg, and a=1336.7(3) pm for Lu4NiMg. The nickel atoms have trigonal prismatic rare earth coordination. These NiRE6 prisms are condensed via common edges to a three-dimensional network ...

Energy Technology Data Exchange (ETDEWEB)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Single-dose and repeated dose toxicity studies of prulifloxacin, a new antibacterial agent, were conducted in aged beagle dogs. I. A single-dose toxicity study Prulifloxacin was administered orally to aged female dogs at a single dose of 2500 and 5000 mg/kg. No death occurred in any group. Vomiting was observed in one of two animals at 2500 mg/kg and in both animals at 5000 mg/kg 3-4 hr after dosing. At 5000 mg/kg, vomiting was observed in both animals after feeding on the day after dosing. One animal also showed soft stool. Thereafter, no abnormalities were observed in any animal. No test article related changes were noted in food consumption, water consumption, body weight or pathological examination in any group. The results show that the lethal dose of prulifloxacin is judged to be greater than 5000 mg/kg in aged female dogs. II. A repeated dose toxicity study Aged male and ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses the following topics: Fusion-fission in light nuclear systems; High-resolution Q-value measurement for the {sup 24}Mg+{sup 24}Mg reaction; Heavy-ion reactions and limits to fusion; and Hybrid MWPC-Bragg curve detector development.

Energy Technology Data Exchange (ETDEWEB)

MmMg{sub 12}-Ni amorphous or nanocrystalline composites (Mm: Ce-rich mischmetal) were prepared through the ball-milling method, and their electrochemical hydrogen storage performance was investigated and compared with that of ball-milled CeMg{sub 12}-Ni composites. It was found that the ball-milled MmMg{sub 12}-Ni composites had larger initial discharge capacities and better high rate dischargeability. Analysis of electrochemical impedance spectra (EIS) shows that the reaction resistance and hydrogen diffusion resistance of the ball-milled MmMg{sub 12}-Ni composites are lower as a result of the decrease in Ce content, and thus can contribute to the larger discharge capacity and better high rate dischargeability. Additionally, the cycle performance of the ball-milled MmMg{sub 12}-Ni composites is better than those of the ball-milled CeMg{sub 12}-Ni composites. ...

International Nuclear Information System (INIS)

NaCl doped MgCl_2.nEtOH adducts were prepared by ball-milling MgCl_2.2.5EtOH with NaCl. Both the ball-milled MgCl_2.nEtOH/NaCl mixture and pure MgCl_2.2.5EtOH adducts were analyzed by X-ray diffraction (XRD), transmission electron microscope (TEM), thermogravimetry (TG) and differencial scanning calorimetry (DSC). A simple MgCl_2.nEtOH/NaCl mixture without ball-milling treatment was also studied for comparison. Two kinds of mixed crystals, Na_2MgCl_4 and NaMgCl_3, were found to be formed in a ball-milled mixture that contained 16 mol.% NaCl. TG and DSC analysis of the samples also provided indirect evidences supporting the presence of the mixed crystals in the ball-milled mixture. Adding certain amounts of NaCl in MgCl_2.2.5EtOH adduct, either by co-milling or by simple mixing, greatly increased the thermal stability of ...

Science.gov (United States)

The authors have presented results of an investigation of wettability of SiC particulates by liquid alloys of the Al-Si-Mg system. The evaluation of wetting has been carried out through the determination of the threshold pressure for infiltration of packed SiC particulates by the liquid alloy. The results indicate that whereas Si and Mg additions do not affect wetting, in the case of the ternary alloys the contact angle decreases in an amount proportional to the content of Mg[sub 2]Si.

International Nuclear Information System (INIS)

A computerised curve-fitting method was developed to calculate the trapping parameters in LiF TLD-100 and LiF:Mg, Ti. After irradiation in a "6"0Co field and with X rays emitted at different voltages the TL process is best described by first-order kinetics. A dependence of the trapping parameters on both the concentration of Mg and Ti and photon energy was detected. (author).

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

International Nuclear Information System (INIS)

The effects of catalytic metal additives on the hydrogen desorption properties of the submicrocrystalline magnesium hydride (#beta#-MgH_2) formed after hydrogenation of the Mg + 10 wt.%X (X = V, Y, Zr) mechanically (ball) milled composites were studied. The composites with catalytic metals were processed by controlled mechanical milling (CMM) in the magneto-mill Uni Ball Mill 5 under protective Ar atmosphere. X-ray diffraction of the milled powders revealed the formation of Mg nanograins (50-60 nm range) interdispersed with the nanograined metal additives within the powder particles. Scanning electron microscopy showed particle size reduction after milling. After activation and hydrogenation in a Sieverts-type apparatus under about 2 MPa pressure of hydrogen, the tetragonal #beta#-MgH_2 hydride co-exists with the small amount of retained unreacted Mg phase and the small amount of ...

International Nuclear Information System (INIS)

Our work deals with accumulative roll bonding (ARB) of pure Mg sheet (0.9mm thickness) and of Al5052 sheet (0.5mm). A stacking of Al-Mg-Al was firstly rolled to 50% reduction at 400"0C and secondly ARB has been processed up to 3 cycles. In such multilayers as well as highly mixed composites of two-phased system texture development, phase reactions and strain accumulation are of basic interest, which needs a combination of different experimental methods for characterization. The present paper deals with the global texture evolution measured by thermal neutrons to average always over the whole sample thickness, SEM and optical microscopy indicates the macroscopic development of Mg and Al layers. The initial materials show typical and strong basal plane texture of hexagonal Mg (17.9mrd) and a recrystallization texture of cubic Al (8.5mrd). Co-deformation of Al/Mg/Al leads to strong ...

International Nuclear Information System (INIS)

In the present work the hydrogen desorption properties of nanostructured magnesium hydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM) of elemental Mg powder under hydrogen are investigated. A profound effect of the particle size of synthesized MgH2 hydride on its hydrogen desorption characteristics measured by differential scanning calorimetery (DSC) has been found. All synthesized MgH2 powders are characterized by a double hydrogen desorption peak. Furthermore, below a certain threshold particle size the DSC desorption temperature of the peak doublet starts decreasing rapidly with decreasing of the mean hydride powder particle size (expressed as equivalent circle diameter-ECD). In contrast, the nanograin (crystallite) size of MgH2 does not seem to have apparent effect on the DSC desorption temperature. It is also observed that for powder particles smaller ...

Energy Technology Data Exchange (ETDEWEB)

In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ball milling. The improved particle size and specific surface ...

International Nuclear Information System (INIS)

Several Mg-Y binary ribbons with Y content up to #approx#17.9 at.% were fabricated by melt-spinning. X-ray diffraction (XRD) revealed that the phase structure changes with increasing Y content from extended solid solution to partially amorphous, and then fully intermetallic Mg_2_4Y_5. Anodic potentiodynamic polarization performed in 0.01 M NaCl electrolyte (pH=12) revealed improved anodic passivity behavior compared to pure Mg for all the Mg-Y alloys. X-ray photoelectron spectroscopy (XPS) revealed that the improved passivity of Mg-Y was more related to the elemental oxidation state rather than the concentration of the surface components. To study the effect of Cl"- ion on the passivity behavior, anodic potentiodynamic and potentiostatic polarization were performed on Mg-17.9 at.% Y in alkaline (pH=12) NaCl electrolytes containing Cl"- ion in the concentration ...

International Nuclear Information System (INIS)

In PWR's steam generators, ''denting'' resulted from corrosion of support plate material, carbon steel is an important problem. The role of chlorides in corrosion acceleration of mild steel was studied. Corrosion tests were conducted at temperature from 100"0C to 280"0C in deaerated solutions of NaCl and MgCl_2 which are main content of sea water. 1) Solution of MgCl_2 was more corrosive than that of NaCl. The more increased in concentration of each chloride solution, the more corrosive in MgCl_2 soln. but the less corrosive in NaCl soln. 2) The rate of corrosion in the mixed solution of NaCl and MgCl_2 was governed by the concentration of MgCl_2 soln. The corrosion behaviour in sea water was suggested to be not controlled by NaCl but by MgCl_2. 3) Acidification of MgCl_2 soln. could be evaluated by experiment at 100"0C, the degree of ...

Energy Technology Data Exchange (ETDEWEB)

The magnetization of ultrathin bcc Fe films (two and three monolayers) on MgO was measured and compared with the behavior predicted for a two-dimensional ferromagnet. The experiment indicated that no hysteresis was present in the magnetization. Instead, the magnetization at low temperature was affected by a marked field cooling effect. These observations lead to the conclusion that films of Fe on MgO of such thickness exhibit superparamagnetic behavior as if they were not entirely continuous. In contrast, films thicker than five monolayers exhibit a magnetic response close to that of bulk iron.

Energy Technology Data Exchange (ETDEWEB)

A small scale biomass metal contacting experiment was performed to screen the optimal plant species for biosorption and bioaccumulation of cadmium, zinc, nickel, lead, and copper. Experiments were also conducted to test the ability of the biomass to lower the metal concentrations below the US Environmental Protection Agency surface water discharge criteria. The minimum residual concentration was 0.1 mg/L for zinc, 0.004 mg/L for lead, and about 0.01 mg/L for cadmium, nickel, and lead. Results indicate that water milfoil can be used for bioremoval of metals.

Science.gov (United States)

... RP-3 exploding bridgewire detonator (Teledyne RISI, 29 mg pentaerythritol tetranitrate (PETN)) and the main charge, which was either 12.7 or 25.4 ...

Science.gov (United States)

Increasing the Mg(2+) concentration results in a depression of succincoxidase-linked state 3

British Library Electronic Table of Contents (United Kingdom)

In this study, the influence of Beryllium (Be) content on the fracture behaviour of Al?15%Mg2Si composite was investigated. The results showed an increase in mechanical properties with increasing of Be content. The stress?strain curves of samples showed a same category of serrations reflecting non-uniform deformation. Scanning electron microscopy was employed to examine the crack nucleation and fracture model. The results indicate that Al?15%Mg2Si composite shows different behaviours of crack initiation and fracture for samples with and without Be. Differences observed in the fracture behaviour were attributed to microstructural changes as well as morphological aspects of primary Mg2Si particles.

British Library Electronic Table of Contents (United Kingdom)

ObjectiveTo study a method of chemical sterilization and its efficacy in adult male stray dogs.MethodsSterilization was performed 45 days after a single bilateral intratesticular injection of calcium chloride (CaCl2) at the doses of 5, 10, 15 or 20 mg per testis per kg body weight.ResultsHistomorphological measures of testes showed total necrosis of testicular tissue at 45 days after an injection of either 10 or 15 or 20 mg CaCl2 along with fibrosis and hyalinization in seminiferous tubules and interstitial spaces. Infiltration of leucocytes was also observed with the 10- or 15-mg dose. Disintegration of germ cell arrangement in seminiferous tubules and washing out of germ cells from the tubules were noted with the 5-mg dose. Relative organ weight, epididymal sperm count, plasma and intrat...

International Nuclear Information System (INIS)

Portuguese 1984. p. 147. Brazil Accursio, WJ Vieira, JGH Kater, CE Chacra,

International Nuclear Information System (INIS)

In the present study 12 diets, each one consisting of a pool of seven day diets, composed by four meals: breakfast, lunch, dinner and snack, adequate in energy and macro nutrients according to the RDA (Recommended Daily Allowance) recommendations, were elaborated and offered to a group of 12 men (19-42 years). The diets were collected by duplicate portion technique and dried by two different processes: freeze drying and 60 deg C ventilated oven drying. In the total, 24 diets were analyzed. The content of some minerals and trace elements (Ca, Fe, Mg, Mn, Na, Se and Zn) were determined by Instrumental Neutron Activation Analysis. The validation of methodology was made by analysis of the reference materials Typical Diet (NIST SRM 1548"a), Orchard Leaves (NIST SRM 1541) and Peach Leaves (NIST SRM 1547). The results observed by two different drying processes used were statistically compared by test T of Student. It was possible to conclude that the concentration means ...

Energy Technology Data Exchange (ETDEWEB)

The ball-milling method was used to produce Mg-50 wt.% ZrFe{sub 1.4}Cr{sub 0.6} composite. The thermodynamic, kinetic, and cycling properties, as well as the resistance to oxidation were examined. This composite possesses excellent kinetic properties, even at moderate temperature. Scanning electron microscopy, energy-dispersive spectrum, transmission electron microscopy and X-ray diffraction were used to characterize the composite before and after hydriding. The fine ZrFe{sub 1.4}Cr{sub 0.6} particles covering Mg particles acting as a ''catalytic film'', a significant amount of imperfections and some alloy powder in the Mg matrix introduced by ball milling all contributed to the enhanced absorption/desorption rate. (orig.)

British Library Electronic Table of Contents (United Kingdom)

A simple enantioselective HPLC method was developed for measuring carfentrazone-ethyl enantiomers. The separation and determination was accomplished on an amylose tris[(S)-a-methylbenzylcarbamate] (Chiralpak AS) column using n-hexane/ethanol (98:2, v/v) as mobile phase at a flow rate of 1.0 mL/min with UV detection at 248 nm. The effects of mobile-phase composition and column temperature on the enantioseparation were discussed. The accuracy, precision, linearity, LODs, and LOQ of the method were also investigated. LOD was 0.001 mg/kg in water, 0.015 mg/kg in soil and wheat, with an LOQ of 0.0025 mg/kg in water and 0.05 mg/kg in soil and wheat for each enantiomer of carfentrazone-ethyl. SPE was used for the enrichment and cleanup of soil, water, and wheat samples. Recoveries for two enantio...

British Library Electronic Table of Contents (United Kingdom)

Atrial fibrillation (AF) is common after coronary artery bypass grafting (CABG) and increases the morbidity and cost. Amiodarone reduces AF after CABG. Ranolazine, an antianginal agent, also prolongs atrial refractoriness and inhibits after depolarizations and triggered activity; effects that could decrease AF after CABG. The present study compared amiodarone versus ranolazine for the prevention of AF after CABG. A retrospective cohort study of patients undergoing CABG at Aspirus Hospital from June 2008 to April 2010. The patients received either amiodarone (400 mg preoperatively followed by 200 mg twice daily for 10 to 14 days) or ranolazine (1,500 mg preoperatively followed by 1,000 mg twice daily for 10 to 14 days). The primary end point was any identified AF after CABG. A total of 393 ...

International Nuclear Information System (INIS)

Polish 2001 p. 105 Poland Bogacz, J. Budzanowski, M. Mazur, J. Swakon,

UK PubMed Central (United Kingdom)

Model phosphate-metal solvation complexes have been studied by ab-initio self-consistent-field techniques. The complexes studied include (RO)2PO2-(R = H or CH3) with Li+, Na+, K+, Be++, Mg++, Ca++,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

High purity MgAl{sub 2}O{sub 4} spinel specimens irradiated in FFTF-MOTA to very high exposure have been examined by three techniques to determine changes in their optical properties. Significant changes were observed in optical absorption, photoluminescence and radioluminescence.

Energy Technology Data Exchange (ETDEWEB)

When used for tissue-equivalent monitoring, the thermoluminescence material LiF:Mg, Cu, P shows an 'under-response' to low-energy photons. This paper explores a new way to increase its low-energy response effectively, and to make it adjustable to some extent, by adding elements with high Z{sub eff}. At the same time its excellent thermoluminescente (TL) performance is maintained. (author).

Energy Technology Data Exchange (ETDEWEB)

We fabricated lauric acid (LA) doped MgB{sub 2} wires and investigated the effects of the LA doping. For the fabrication of the LA-doped MgB{sub 2} wires, B powder was mixed with LA at 0-5 wt.% of the total amount of MgB{sub 2} using an organic solvent, dried, and then the LA-treated B and Mg powders were mixed stoichiometrically. The powder mixture was loaded into an Fe tube and the assemblage was drawn and sintered at 900 deg. C for 3 h under an argon atmosphere. We observed that the LA doping induced the substitution of C for the B sites in MgB{sub 2} and that the actual content of C increased monotonically with increasing LA doping level. The LA-doped MgB{sub 2} wires exhibited a lower critical temperature (T{sub c}), but better critical current density (J{sub c}) behavior in a high magnetic field: the 5 wt.% LA-doped sample had a J{sub c} value of 5.32 x ...

Wastenet

... However blaming vitamin supplements on deaths, or mortality is silly, as the studies are not exactly kosher. Vitamin C in 2,000mg is good for allergies, and niacin (b3) in 10,0000mg is good for depression. This is all examples on how vitamin supplements can help. I call it a security blanket, as food these days is not so good due vitamin and mineral damage due to light, or storage. By the time we eat the apple from the supermarket, there is minimal vitamin and ...

International Nuclear Information System (INIS)

Research highlights: #-># The Y-intermetallic can accelerate corrosion and Y can increase the protectiveness of the surface layer. #-># In 0.1 M NaCl, the corrosion rate of Mg-Y alloys increased with increasing Y due to the Y intermetallic. #-># In 0.1 M NaCl, there was filiform corrosion. #-># In 0.1 M Na_2SO_4, the corrosion rate of Mg-Y alloys decreased with increasing Y in the range 3-7%Y. #-># Hydrogen evolution was observed from particular parts of the alloy surface. - Abstract: Corrosion of Mg-Y alloys was studied using electrochemical evaluations, immersion tests and direct observations. There were two important effects. In 0.1 M NaCl, the corrosion rate increased with increasing Y content due to increasing amounts of the Y-containing intermetallic. In 0.1 M Na_2SO_4, the corrosion rate decreased with increasing Y content above 3%, attributed to a more protective surface film, despite the ...

International Nuclear Information System (INIS)

Electron-excitation cross sections are reported for the 3s "2S#->#3p "2P(h,k) resonance transition in Mg"+ at energies from threshold (4.43 eV) to approximately 9 times threshold (40.0 eV). The electron-energy-loss merged-beams technique used in these measurements is described in detail. In addition, the method of separating contributions of the elastically scattered (Coulomb) and the inelastically scattered electrons in the present Mg"+ case and previously reported Zn"+ results [Phys. Rev. Lett. 67, 30 (1991)] is described. Comparisons in the experimental energy range are made for Mg"+ with the two five-state close-coupling theoretical calculations carried out herein, and with other published close-coupling, distorted-wave, and semiempirical calculations. The present Mg"+ cross sections and Zn"+ cross sections from earlier measurements are tabulated.

Energy Technology Data Exchange (ETDEWEB)

Adenosine triphosphate (ATP) is an alternative to dipyridamole or adenosine in thallium-201 myocardial scintigraphy. However, the optimal dose of ATP has not been determined. A Doppler guide wire study showed the coronary flow velocity at a dose of 0.15 mg/kg of ATP was equal or higher than that at 0.14 mg/kg of adenosine or 0.56 mg/kg of dipyridamole. ATP was given intravenously to 67 patients with coronary artery disease at 0.15 mg/kg/min for 6 min. Thallium-201 was injected at 3 min, followed by immediate and delayed (3 hrs) tomographic imaging. There was no serious side effect during examination, although chest pain (26%), dyspnea (17%), and flushing (33%) were common. The sensitivity and specificity to detect coronary artery disease were 98 and 100%, respectively. The sensitivity to detect left anterior descending artery, left circumflex artery, and right coronary artery lesions was 94, 59 and 77%, ...

International Nuclear Information System (INIS)

Optimum analytical conditions of the aluminium ion were established by flow injection analysis. Eriochrome Cyanine R(ECR) dye reacts with the aluminium ion at pH 6.0 form a complex that exhibits maximum absorption at 535 nm. Reaction condition including the mixing and the reaction coil length, the concentration and the pH of the buffer solution, temperature, and injection loop volume were optimized to introduce this reaction into flow injection analysis. The results were as follows. A mixing coil length of 0.5 m and a reaction coil length of 4.0 m, the pH 6.0 and 1M of acetate buffer solution, the ECR concentration of 0.56 mM, the reaction temperature of 40 .deg. C, the injection loop volume of 300 #mu#L were chosen as optimum conditions. Under these conditions the detection limit of the aluminium ion was less than 0.05 mg/L and the repeatability was better than 1%. A sampling frequency of 24 times for an hour was achieved. Interfering ions such as F"-, HPO_4"2"-, ...

British Library Electronic Table of Contents (United Kingdom)

We present structure calculations of neutral and singly ionized Mg clusters of up to 30 atoms, as well as Na clusters of up to 10 atoms. The calculations have been performed using density functional theory (DFT) within the local (spin-)density approximation, ion cores are described by pseudopotentials. We have utilized a new algorithm for solving the Kohn-Sham equations that is formulated entirely in coordinate space and, thus, permits straightforward control of the spatial resolution. Our numerical method is particularly suitable for modern parallel computer architectures; we have thus been able to combine an unrestricted simulated annealing procedure with electronic structure calculations of high spatial resolution, corresponding to a plane-wave cutoff of 954 eV for Mg. We report the geo...

International Nuclear Information System (INIS)

A simple method is presented for the separation of lead-203 from copper-backed thallium cyclotron targets. The procedure involves cation-exchange chromatography in hydrochloric acid and hydrochloric acid-acetone mixtures. Further purification involves anion-exchange chromatography in nitric acid-hydrobromic acid mixtures. A cation-exchange column containing 3.0 g of resin can handle as much as 15 g of thallium and 160 mg of copper. An anion-exchange column containing 3.0 g of resin can separate lead from up to 200 mg of thallium and 10 mg of copper. Separations are extremely sharp and less than 0.1 #mu#g of thallium and less than 0.1 #mu#g of copper remain in the lead-203 fraction. (author).

Energy Technology Data Exchange (ETDEWEB)

The magnetic properties of diluted spinels Zn{sub 1-x}M{sub x}Fe{sub 2}O{sub 4} (M = Mg, Ni) systems have been studied by mean field theory, probability law and high-temperature series expansions method in the range 0 {<=} x {<=} 1. The exchange interactions are calculated by the first and second theory, respectively. The magnetic phase diagrams of Zn{sub 1-x}M{sub x}Fe{sub 2}O{sub 4} (M = Mg, Ni) are calculated by the high-temperature series expansions, combined with the Pade approximants method. The critical exponent associated with the magnetic susceptibility ({gamma}) is deduced.

International Nuclear Information System (INIS)

The effect of exposure to gamma rays on LPO contents in liver, spleen and kidney of mice and the anti-lipid-peroxidation of preparations of chinonin, tannic acid and squalene were reported. All these preparations were given by intragastric perfusion. For LPO, a modified method of TBA spectrophotometry was used for determination. The results show that LPO contents in tissues increased 72 h after whole-body exposure of mice to gamma rays, that in range of 0-4 Gy, there was a linear relationship between radiation doses and LPO contents, and that all three preparations were effective in reduction of the LPO content in liver, spleen and kidney of mice, with chinonin (at dose of 0.35 mg/mouse#centre dot#day) being more effective than tannic acid (at dose of 15 mg/mouse#centre dot#day) and squalene (at dose of 0.6 mg/mouse#centre dot#day).

Energy Technology Data Exchange (ETDEWEB)

Medicinal plants are available in the markets in Belo Horizonte, Minas Gerais. The objective of this work is to investigate the Ca, Cr, Cu, Fe, K, Mg, Na e Zn concentrations in two lots of usually known diuretics plants (azeitona do mato, cabelo de milho, cavalinha, cervejinha do campo, chapeu de couro, congonha de bugre, marmelinho do campo and quebra pedra) bought with an interval of time - six months - between the purchases. The elemental concentrations were determined applying k{sub 0} instrumental neutron activation analysis and atomic absorption spectrophotometry analysis. (author)

British Library Electronic Table of Contents (United Kingdom)

Fresh rhizomes of 18 diploid and tetraploid genotypes of Indian ginger, including commercial cultivars and experimental genotypes, were assayed for gingerol content and antioxidant activity. The tetraploid ginger type was derived from the respective diploid ginger by shoot tip culture. [6]-Gingerol was identified as the major pungent phenolic compound in all samples (mean 1354.78+/-470mg/g), while [8]- (mean 180.94+/-45mg/g) and [10]-gingerol (mean 234+/-79mg/g) occurred in lower concentrations. The total gingerol content of the tetraploid type was much higher than that of the respective diploid type and especially the [10]-gingerol. Both diploid and tetraploid types of the cv. Meghalaya Local contained the highest level of gingerol. At both ploidy levels, the genotypes showed significant ...

Science.gov (United States)

A developed flue gas desulfurization and dust removal process with a cross-flow moving bed filled with activated coke (AC) was tested on a pilot scale with the gas treatment capacity of 1000 mg x h(-t). The results show that a easy-operating and stable-running pilot-scale testing equipment can be reached, and under the conditions of testing space velocity, the feed gas temperature of 120 degrees C, SO2 concentrations of 3232-6006 mg x m(-3) and dust concentration of 89.3-1599.7 mg x m(-3), the high efficiency of flue gas desulfurization and dust removal is reached with the purity of dust less than 50 mg x m(-3). In the technology, the spent AC was regenerated by heating, and the SO2 concentration in the desorption gas is about 40.1%, which can be efficiently recovered as a sulfur resource. Favorable economy benefit can be reached by using the process. PMID:16850821

Energy Technology Data Exchange (ETDEWEB)

FT-IR spectroscopic studies of the adsorption of natural and {sup 18}O-enriched NO gases on thermally and cleaned MgO powders were carried out. The temperature dependence of the IR spectra was investigated to characterize the adsorbate species. Three types [1, 2, and 3] of NO adsorptions were obtained in the wavenumber region of 1500--1000 cm{sup {minus}1}. Those types were examined using density functional theory [(U)B3-LYP/6-31G*] vibrational analyses of (MgO){sub n}-NO cluster calculations. Types 1, 2, and 3 were assigned to monodentate, asymmetric, and symmetric bidentate geometries, respectively. A type 4, a tridentate model which involves a NO{sub 3}-like species, was calculated and was found to give wavenumbers of less than 1,000 cm{sup {minus}1}. The splitting of IR bands of type 3 due to the {sup 15}N{sup 18}O adsorbate was ascribed to the oxygen exchange, {sup 15}N{sup 18}O {yields} {sup 15}N{sup 16}O, via the reaction {sup 16}O-{sup ...

Energy Technology Data Exchange (ETDEWEB)

Short communication

UK PubMed Central (United Kingdom)

The intracellular concentration of protein may be as high as 400 mg per ml; thus it seems inevitable that within the cell, numerous protein-protein contacts are constantly occurring. A basic biochemical...Full Text Available

CERN Document Server

We present structure calculations of neutral and singly ionized Mg clusters of up to 30 atoms, as well as Na clusters of up to 10 atoms. The calculations have been performed using density functional theory (DFT) within the local (spin-)density approximation, ion cores are described by pseudopotentials. We have utilized a new algorithm for solving the Kohn-Sham equations that is formulated entirely in coordinate space and, thus, permits straightforward control of the spatial resolution. Our numerical method is particularly suitable for modern parallel computer architectures; we have thus been able to combine an unrestricted simulated annealing procedure with electronic structure calculations of high spatial resolution, corresponding to a plane-wave cutoff of 954eV for Mg. We report the geometric structures of the resulting ground-state configurations and a few low-lying isomers. The energetics and HOMO-LUMO gaps of the ground-state ...

Energy Technology Data Exchange (ETDEWEB)

Fe-sheathed MgB{sub 2} tapes with cheap stearic acid, Mg stearate and Zn stearate doping were prepared through the in situ powder-in-tube method. It is found that J{sub c}, H{sub irr} and H{sub c2} were significantly enhanced by doping. Compared to the pure tapes, J{sub c} for all the doped samples was improved by more than an order of magnitude in a high-field regime. At 4.2 K, the transport J{sub c} reached 2.02 x 10{sup 4} A cm{sup -2} at 10 T for the Zn stearate doped tapes and 3.72 x 10{sup 3} A cm{sup -2} at 14 T for the stearic acid doped samples, respectively. Moreover, at 20 K, H{sub irr} for the Zn stearate doped tape achieved 10 T, which is comparable to that of the commercial NbTi at 4.2 K. The improvement of J{sub c}-H properties in doped samples can be attributed to the increase of H{sub c2} resulting from the incorporation of C atoms into the MgB{sub 2} crystal lattice as well as a high density of ...

UK PubMed Central (United Kingdom)

A procedure was developed to isolate polyribosomes from plant cell cultures. Tobacco callus extracted in 10 mm MgCl₂, 80 mm KCl, 250 mm sucrose, and 140 mm...Full Text Available

UK PubMed Central (United Kingdom)

The pharmacokinetics of fusidic acid and 3-ketofusidic acid were investigated in cholestatic and noncholestatic patients after intravenous administration of single and multiple doses of 500 mg of sodium...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Although the subtrate binding properties of adenylate kinase (AK) have been studied extensively by various biochemical and biophysical techniques, it remains controversial whether uncomplexed adenosine 5'-triphosphate (ATP) binds to the adenosine 5'-monophosphate (AMP) site of AK. The authors present two sets of experiments which argue against binding of ATP to the AMP site. (a) /sup 31/P nuclear magnetic resonance titration of ATP with AK indicated a 1:1 stoichiometry on the basis of changes in coupling constants and line widths. This ruled out binding of ATP to both sites. (b) ATP and MgATP were found to behave similarly by protecting AK from spontaneous inactivation while AMP showed only a small degree of protection. Such inactivation could also be protected or reversed by dithioerythritol and is most likely due to oxidation of sulfhydryl groups, one of which (cysteine-25) is located near the MgATP site. The results support ...

UK PubMed Central (United Kingdom)

The responses of the vacuolar membrane (tonoplast) proton-pumping inorganic pyrophosphatase (H⁺-PPase) from oat (Avena sativa L.) roots to changes in Mg²⁺ and...Full Text Available

International Nuclear Information System (INIS)

Purpose. To evaluate injection-associated pain, safety, and efficacy with the isotonic contrast medium iodixanol (Visipaque 270 mg I/ml) compared with iopromide (Ultravist 300 mg I/ml) in femoral arteriography. Methods. A multicenter, double-blind, randomized, parallel-group clinical investigation was carried out in 54 hospitals in Europe. Of the patients evaluated, 1225 received iodixanol and 1227 iopromide in conventional and/or digital subtraction angiography. Results. The iodixanol group reported statistically significantly less injection-associated pain (0.9%) than the iopromide group (9.5%) (p<0.001). Further, 4.1% in the iodixanol group experienced pain and/or severe heat sensation vs 19.8% in the iopromide group (p<0.001). In the iodixanol group, 1.8% of the patients experienced contrast-related adverse events vs 2.4% in the iopromide group (p=NS). Overall diagnostic information was optimal for 94.1% in the iodixanol group and ...

UK PubMed Central (United Kingdom)

Microalbuminuria (26-250 mg/d) is considered to be an indicator of incipient diabetic nephropathy in humans in insulin-dependent diabetes (IDD). However, before microalbuminuria is observed, glomerular...Full Text Available

Science.gov (United States)

... were given daily i.p. injections of either sesame oil (2.5 ml/kg, vehicle control) or VCD dissolved in sesame oil (80 mg/kg, 0.57 mmol/kg) for ... ...

UK PubMed Central (United Kingdom)

The nephrotoxicity of cefoxitin was studied in a rat model of impaired renal function. Two levels of renal impairment were produced: "moderate," with blood urea concentrations of 100 to 150 mg/100 ml...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The biosorption of phosphate from aqueous solutions using Fe(III)-treated Staphylococus xylosus cells was investigated. Langmuir and Freundlich isotherm models were applied to describe the adsorption equilibrium and found that Langmuir isotherm model fitted the equilibrium data better than Freundlich isotherm model. The biosorption capacity of Fe(III)-treated biomass for phosphate was found to be 70.92mg/g at optimum conditions of pH 3.0, biomass concentration 0.5g/L and equilibrium phosphate-biomass time 60min respectively. The sorption efficiency at initial phosphate concentration of 50mg/L was not influenced upon addition of SO4^2^-, Cl^-, CO3^2^-, NO3^-, Mg^2^+ and Ca^2^+ ions from 0 to 800mg/L, whereas under the same conditions, phosphate sorption was increased with increase in concen...

International Nuclear Information System (INIS)

We studied the effects of co-doping with Li and Al on the energy gaps of MgB2 by performing point-contact Andreev-reflection spectroscopy (PCAR) in polycrystalline Mg1-x(Al?Li1-?)xB2 samples with x?0.4. Even though the lattice parameters and the critical temperature of the compound simply scale with the effective Al content ?x, irrespective of the Li concentration, the energy gaps do not. In particular, for a given effective Al content, the comparison with Mg1-y(Al)yB2 with y = ?x shows that the ? bandgap is practically the same while the ? bandgap is higher. A clear gap merging is observed in the most doped sample (x = 0.4) when Tc<20 K. The results are discussed within the two-band Eliashberg theory and compared to the outcomes of first-principles calculations of the effects of Li and Al co-doping on the electronic structure of magnesium diboride.

Energy Technology Data Exchange (ETDEWEB)

WR-2721 (S-2-(3-aminopropylamino)ethylphosphorothioic acid) has been demonstrated to be cytotoxic to stem spermatogonia in the mouse. Five and 10 injections of 300 mg/kg killed sufficient numbers of stem cells to reduce sperm production 56 days after treatment by 16 and 43%, respectively. Single injections of 300 or 400 mg/kg of WR-2721 given 15 min after irradiation produced negligible toxicity to stem cells as measured by counts of repopulated tubules; 600 mg/kg reduced stem cell survival by 47%. Four daily injections of 300 mg/kg given 4, 3, 2, and 1 days prior to irradiation reduced stem cell survival by about 60%. The cytotoxic effects of WR-2721 on testicular stem cells at least partially explains the reduced protection factors observed in the testis with low doses of radiation and during fractionated treatments involving multiple injections of drug.

UK PubMed Central (United Kingdom)

Calcium requirements of North American adolescents were set at 1300 mg/day based on data from white girls. Calcium requirements for Asian-American adolescents have not been studied. Using metabolic...Full Text Available

Science.gov (United States)

Record production of heavy water was achieved: the plants at Glace Bay and Port Hawkesbury, Nova Scotia, produced a total of 560 megagrams. A shipment of 500 Mg was delivered on time to the Wolsung CANDU reactor in Korea. Energy conservation and waste hea...

Science.gov (United States)

Jun 16, 2011 ... Results indicated that fuel loadings averaged 24.05 Mg ha 1 in 2004–2006. Forest litter decreased from wetter to drier forest life zones. ...

International Nuclear Information System (INIS)

The "2"0 "2"1 "2"2Ne("6Li, d)"2"4 "2"5 "2"6Mg reactions have been studied at a bombarding energy of 32 MeV. Alpha particle spectroscopic strengths have been extracted for several low-lying levels by a finite-range distorted wave analysis. These are compared with theoretical predictions. The agreement is good both for relative strengths to different levels within a nucleus and for ground-state strengths relative to the "1"6O("6Li, d) result. Strengths calculated using eigenfunctions determined in large shell-model computations agree well with pure symmetry SU(3) predictions. The "2"1Ne("6Li, d) angular distributions for transitions to the ground-state band of "2"5Mg are characterized by the lower of the two L-transfers allowed for populating each level. For the 3"+(5.24 MeV) unnatural parity level in "2"4Mg, a two-step calculation gives a better account of the data than does a compound nuclear calculation. (Auth.).

International Nuclear Information System (INIS)

Crystallization points of aqueous solution of the systems M(ClO_4)_2-H_2O (M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+), depending on the salt concentration, were identified by visual-polythermal method. Relying on model notions on the structure of the electrolyte solutions, specific features of strontium perchlorate solubility polytherm and concentration dependence of the relative dynamic viscosity of the salt aqueous solutions are discussed

International Nuclear Information System (INIS)

Doubly-excited 2s-12p-13pnp autoionizing resonance series of Ne atom as well as autoionizing resonances in the 2s region of Na and Mg atoms have been studied with monochromatized synchrotron radiation. Use of charge-separated photoion-yield method allowed us to detect these weak resonances in a clarified way in the yield curves of doubly-charged ions. The observed resonance states have been interpreted with the help of MCDF calculations, and the decay processes of these resonance states are discussed briefly.

Science.gov (United States)

In this study, different proportions of silver-palladium alloy used as an inner electrode are adopted to fabricate (Zn,Mg)TiO3-based multilayer ceramic capacitors. Effects of sintering temperature, and measuring frequency on the dielectric properties of the samples with different proportions of the Pd-Ag inner electrode are investigated. The continuity of the inner electrode and the proportion of Pd-Ag of the inner electrode of samples sintered at different temperatures play important roles in determining the dielectric properties.

Science.gov (United States)

Antiquitin (ATQ) deficiency is the main cause of pyridoxine dependent epilepsy characterized by early onset epileptic encephalopathy responsive to large dosages of pyridoxine. Despite seizure control most patients have intellectual disability. Folinic acid responsive seizures (FARS) are genetically identical to ATQ deficiency. ATQ functions as an aldehyde dehydrogenase (ALDH7A1) in the lysine degradation pathway. Its deficiency results in accumulation of ?-aminoadipic semialdehyde (AASA), piperideine-6-carboxylate (P6C) and pipecolic acid, which serve as diagnostic markers in urine, plasma, and CSF. To interrupt seizures a dose of 100mg of pyridoxine-HCl is given intravenously, or orally/enterally with 30mg/kg/day. First administration may result in respiratory arrest in responders, and thus treatment should be performed with support of respiratory management. To make sure that late and masked response is not missed, treatment with oral/enteral ...

International Nuclear Information System (INIS)

Carbothermal reduction-nitridation (CRN) of talc (Mg_3(Si_2O_5)_2(OH)_2) and halloysite (Al_2Si_2O_5(OH)_4) clay provides a useful route for preparing low-cost Mg-#alpha# sialon powder. In this study, the chosen molecular ratios of talc to halloysite were 0.1:1, 0.2:1, 1.5:1.0 and 2.0:1. The CRN reaction was conducted at 1450 to 1520 deg C and 2 to 6h holding time using carbon black as a reducing agent in flowing N_2 (gas). The results showed the synthesized powder was composed of #alpha#-sialon, #beta#-sialon and small amounts of SiC, 15R and AlN phases that greatly depended on the ratio of talc to halloysite, the reaction temperature and holding time. The highest content of Mg-#alpha# sialon, as much as 90wt%, was achieved at 1480 deg C for a holding time of 4h at a talc to halloysite ratio of 1.5:1.0. SiC was considered as an intermediate compound. We also discuss the evaporation loss of Mg caused by ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium-based alloys are among the promising materials for hydrogen storage and fuel cell applications due to their high hydrogen content. In the present work, we investigated the hydrogen release/uptake properties of the Mg-Ti-H system. Samples were prepared from the mixtures of MgH{sub 2} and TiH{sub 2} in molar ratios of 7:1 and 4:1 using a high-energy-high-pressure (HEHP) mechanical ball-milling method under 13.8 MPa hydrogen pressure. Thermogravimetric analysis (TGA) showed that a relatively large amount of hydrogen (5.91 and 4.82 wt.%, respectively, for the above two samples) was released between 126 and 313 C while temperature was increased at a heating rate of 5 C min{sup -1} under an argon flow. The onset dehydrogenation temperature of these mixtures, which is 126 C, is much lower than that of MgH{sub 2} alone, which is 381 C. The activation energy of dehydrogenation was 71 kJ mol{sup -1}, which is much smaller ...

Energy Technology Data Exchange (ETDEWEB)

Adsorpt1on of CH[sub 4] and coadsorption of CH[sub 4] and CO on differently treated magnesium oxide have been studied by FT-IR spectroscopy at 173-273 K. Five IR bands at 3008, 3000, 2900, 2890, and approximately 1306 cm[sup [minus]1] were observed when well-outgassed MgO was exposed to CH[sub 4] at 173 K. The bands at 3008 and 3000 cm[sup [minus]1] are assigned to a degenerate stretch vibration of CH[sub 4], and those at 2900 and 2890 cm[sup [minus]1] originate from an infrared-forbidden mode at 2917 cm[sup [minus]1] of free CH[sub 4]. These bands became noticeably stronger with the outgassing temperature of MgO but could be sufficiently reduced as MgO was pretreated in air or under water vapor. Adsorbed CO on MgO gives two IR bands at 2161 and 2155 cm[sup [minus]1] which exhibit a parallel variation with those bands of adsorbed CH[sub 4] with the different pretreatments of MgO. ...

Energy Technology Data Exchange (ETDEWEB)

Various methods for storing hydrogen have been examined in an effort to find ways to store hydrogen in increasingly smaller volumes with decreasing weight of the whole hydrogen storage system. Metal hydrides, in which hydrogen is chemically bound to a metal atom, are considered to be very promising candidates for hydrogen storage because they have high gravimetric and volumetric storage capacities. This study investigated the effect of different magnesium (Mg) and aluminium (Al) ratios on the absorption and desorption properties of thin films. Neutron reflectometry (NR) was used in this study to better understand the absorption and desorption properties of commercially promising hydrogen storage materials. The large negative scattering length of hydrogen atoms changes the reflectivity curve substantially, so that NR can determine the total amount of stored hydrogen as well as the hydrogen distribution along the film normal, with nanometer resolution. In order to ...

Science.gov (United States)

The technology for flue gas desulfurization (FGD) with seawater is widely adopted by coal-fired power plants in coastal areas. SO2 in the flue gas is absorbed by alkaline seawater and transfered in aqueous phase as sulfite (SO3(2-)), and most SO3(2-) is transformed to sulfate (SO4(2-)) after an aeration process. The remaining SO3(2-) in the seawater discharged to sea area may be harmful to marine organism because of its biological toxicity, thus it is necessary to determine the concentration of SO3(2-) in the seawater for desulfurization. In this study, the method of determination of SO3(2-) in the seawater by ion chromatography was investigated. The separation was achieved on an IonPac AS14A column with 14 mmol/L NaOH-12 mmol/L Na2 CO3 solution as the mobile phase at a flow rate of 1.2 mL/min, and the detection was performed by a pulsed amperometric detector. Formaldehyde was added as a protective agent when sampling because the SO3(2-) is easy to be oxidized. To avoid the formation ...

Energy Technology Data Exchange (ETDEWEB)

In order to overcome the inherent disadvantages of Ti-V-based hydrogen storage alloys, such as poor activation behavior and low high-rate dischargeability, the novel composites Ti{sub 0.17}Zr{sub 0.08}V{sub 0.35}Cr{sub 0.1}Ni{sub 0.3}-x wt.% La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} (x = 0, 5, 10 and 20) were successfully synthesized by ball milling method in the present study. And the structure and overall electrochemical properties of as-prepared composites are investigated systemically. The electrochemical studies show that the maximum discharge capacity of the composite electrodes displays no variation with the increase of La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} content, whereas the high-rate dischargeability (HRD) and the activation behavior are distinctly improved with increasing x. The electrochemical hydrogen kinetics of composite electrodes is also studied by means of electrochemical impedance spectroscopy (EIS), linear ...

Energy Technology Data Exchange (ETDEWEB)

Pulmonary fibrosis was produced in mice treated with butylated hydroxytoluene (BHT) 400 mg/kg and immediately exposed to 80% oxygen for 3 days. This treatment regimen resulted in 47% mortality. Surviving mice exhibited significant accumulations of pulmonary collagen as evidence by increases in total lung hydroxyproline levels. The administration of indomethacin (4 mg/kg/day) on days 1-6 after BHT decreased mortality to 14% and diminished the accumulation of collagen in lung tissue. Indomethacin also enhanced survival when administered on days 1-3 after BHT/O/sub 2/ but had no effect on lung collagen levels. Treatment with indomethacin on days 4-6 after BHT had no beneficial effect. The administration of prednisolone (60 mg/kg/day) on days 1-3, 1-6, or 4-6 after BHT decreased mortality but had not effect on accumulation of lung collagen. Cis-4-hydroxyproline (400 mg/kg/day) also had no effect on ...

Energy Technology Data Exchange (ETDEWEB)

The Anadenathera macrocarpa, Schinus molle, Hymenaea courbaril, Cariniana legalis, Solidago microglossa and Stryphnodendron barbatiman, were collected ''in natura'' samples (leaves, flowers, barks and seeds) from different commercial suppliers. The pharmaco-active compounds in ethanolic extracts had been made by the Mato Grosso Federal University (UFMT). The energy-dispersive x-ray fluorescence (ED-XRF) spectrometry was used for the elemental analysis in different parts of the plants and respective ethanolic extracts. The Ca, Cl, Cu, Fe, K, Mg, Mn, Na, Ni, P, Rb, S, Sr and Zn concentrations were determined by the fundamental parameters method. Some specimens showed a similar inorganic profile for ''in natura'' and ethanolic extract samples and some ones showed a distinct inorganic profile. For example, the Anadenathera macrocarpa showed a similar concentration in Mg, P, Cu, ...

Energy Technology Data Exchange (ETDEWEB)

The feasibility of using desferrioxamine (DF), an iron chelator, as a therapeutic agent against paraquat (PQ/sup + +/) toxicity in male Sprague-Dawley rats was explored, based on the rationale of limiting toxic hydroxyl radical production from hydrogen peroxide by removing redox-active iron. Body weights, mortality, and lung histopathology were followed for periods up to 14 days after intraperitoneal injection of PQ/sup + +/ (20 or 25 mg/kg body weight) with or without concurrent daily subcutaneous injections of DF (300 mg/day). Animals receiving PQ/sup + +/ showed the expected typical patterns of mortality and of lung histopathology, namely: marked edema, subpleural hemorrhage, acute inflammation, perivascular mononuclear cell infiltrates, sloughing of alveolar and bronchiolar lining cells, and diffuse interstitial fibrosis. Desferrioxamine alone was non-toxic. Surprisingly, results when both PQ/sup + +/ and DF were administered indicated a ...

Energy Technology Data Exchange (ETDEWEB)

Digested sewage sludge was applied to pastures and tree plantations at 19 to 44 Mg/ha (dry weight) as part of a municipal sludge disposal program. The sludge had low concentrations of heavy metals and traces of /sup 137/Cs and /sup 60/Co. Monitoring of soils, soil solutions, and runoff indicated that N, P, heavy metals, and radionuclides were largely retained in the upper 15cm of the soil. Soil solutions had elevated NO/sub 3//sup /minus// concentrations often >100 mg/L, but no significant increases in groundwater NO/sub 3//sup /minus// were found during the first year. Runoff from active sites had elevated concentrations of NO/sub 3//sup /minus// (20--30 mg/L), soluble P (1 mg/L), BOD/sub 5/ (5--30 mg/L), and fecal coliform (up to 14,000 colonies per 100 ml), not unlike runoff from pastures with cattle. Enrichment of organic N (2 times), available (inorganic) N (5 to 10 times), ...

Energy Technology Data Exchange (ETDEWEB)

Food-grade PVC and PVDC/PVC films containing 28.3% dioctyladipate (DOA) and 5.0% acetyltributylcitrate (ATBC) plasticizers, respectively, were brought into contact with olive oil and were irradiated with {gamma}-radiation [{sup 60}Co] at doses equal to 4 kGy and 9 kGy corresponding to `cold pasteurization`. Irradiation was carried out at 8-10 C and samples were subsequently stored at 4-5 C. Contaminated oil samples were analysed for DOA and ATBC at intervals between 7 h and 97 h of contact, using an indirect GC method. Identical non-irradiated (control) samples were also analysed for DOA and ATBC content. Results showed no statistically significant differences in migrated amounts of DOA and ATBC between irradiated and non-irradiated samples. Neither were differences observed between samples irradiated at 4 kGy and 9 kGy. This was supported by identical IR spectra recorded for irradiated and non-irradiated samples and leads to the conclusion that at such intermediate radiation doses ...

Energy Technology Data Exchange (ETDEWEB)

To assess the contribution of adrenal-derived androgens in women with hirsutism, adrenal scintigrams under dexamethasone suppression (DS) were performed on 35 women with increasing facial or body hair and irregular or absent menses. Based upon the DS regimen chosen (8 mg/d for 2 days or 4 md/d for 7 days before the injection of 6..beta..-(/sup 131/I)iodomethylnorcholesterol), three imaging patterns were identified. The first was the absence of uptake before 3 days (8-mg DS) or before 5 days (4-mg DS) after injection. This imaging pattern was seen in 17 of the 35 patients studied and was considered normal. The second pattern was bilateral uptake earlier than 3 days (8-mg DS regimen) or 5 days (4-mg DS) after injection. This was seen in 13 of the 35 patients and was interpreted as bilateral early visualization. Adrenal-vein catheterization performed on six patients with this pattern ...

Energy Technology Data Exchange (ETDEWEB)

The untreated, heat- and alkali-treated Lentinus sajor-caju mycelia were used for the recovery of uranium from aqueous solutions. The effect of pH, temperature, initial concentration of UO{sub 2} {sup 2+} ions and contact time parameters were investigated in a batch system. The particles sizes of the fungal mycelia were ranging from 100 to 200 {mu}m. Biosorption equilibriums were established in about 30 min and the correlation regression coefficients show that the adsorption process can be well defined by the Freundlich equation. The alkali treated form had a high biosorption capacity (378 mg/g) than those of the untreated (268 mg/g) and heat-treated fungal mycelia (342 mg/g). Optimum biosorption was observed at pH 4.5 for all the tested fungal preparations and was independent of temperature (5-35 deg. C). In addition, the polarity and surface energy of the fungal biomass film preparations were determined by contact angle ...

Energy Technology Data Exchange (ETDEWEB)

Spent oxide fuels are reduced in a molten salt of CaCl[sub 2]-CaF[sub 2] to convert them into metals, then melted in an Fe-U bath disposed in an electrolytic refining vessel and brought into contact with molten Mg, to extract transuranium elements and rare earth elements contained in the Fe-U bath as metals in the molten Mg. Then molten Mg is removed and the residue is brought into contact with KCl-LiCl molten salt and electrolyzed using the Fe-U as an anode. Then, uranium is recovered by deposition on an iron cathode disposed in chloride electrolytes of the electrolytic refining vessel. Uranium and transuranium elements can be thus separated and, for example, depleted uranium for use in blanket fuels can be recovered easily. This can greatly reduce the temporary storage amount of depleted uranium, to eliminate requirement for a large-scaled facility used exclusively for storing uranium and long time management for uranium. ...

Energy Technology Data Exchange (ETDEWEB)

In a prior study, we demonstrated that certain disposable coils are contaminated with zinc and release substantial quantities of Zn during hemodialysis, producing high post-dialysis plasma Zn concentrations. The present investigation was designed to monitor plasma and dialysis fluid Zn and copper throughout dialysis and to estimate patient Zn and Cu uptake. Venous plasma, arterial plasma and coil chamber fluid were sampled periodically throughout dialysis; trace metal concentrations were determined by flame atomic absorption spectrophotometry. Release of considerable quantities of Zn from the coils into the dialysis fluid, with uptake into the patient's plasma, was found. Approximately one-half of the plasma Zn uptake occurred in the first 45 minutes. Coils from different lots released significantly different quantities of Zn. Patient uptake of Zn ranged from 3.2 mg-23.0 mg, with a mean of 15.0 +- 6.1 mg. Copper ...

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence analysis and fast neutron activation analysis were used for the determination of chromium. The excitation source for X-ray fluorescence analysis was a ring-shaped "2"4"1Am source with an activity of 18.5x10"9 Bq. SYNPOR filters of 35 mm in diameter were used for the measurement. The 5.414 keV Cr peak was measured with a Si(Li) detector. The sensitivity was 0.05 mg for a period of measurement of 1000 s. A neutron generator with an emission of 10"9 s"-"1 was used as the source of fast neutrons. "5"2V and "5"3V, the products of nuclear reaction with Cr, were measured gamma spectrometrically with a Ge(Li) detector. The sensitivity for Cr is 0.015 mg, in the presence of Mn which causes interference the sensitivity is a mere 0.075 mg. The mentioned methods were used to determine total Cr and Cr(VI) in welding aerosols. It was found that the most toxic form, i.e., Cr(VI), is released during manual ...

International Nuclear Information System (INIS)

Column chromatography of the petroleum ether and chloroformic extracts of Maytenus Forsskaoliana afforded four compounds: friedilin1, B-amyrin 2, B-sitosterol 3 and betulin 4. The structure of these compounds were established on bases of spectral (IR,MS,H and C-NMR)as well as physical data. Antimicrobial activity for extracts indicated weak potency (200ug/ml) while betulin4 showed a pronounced activity (MIC and MBC 20ug/ml).The cytotoxic activity of beutalin4 significantly indicated promising activity (IC50 40ug/ml) on both HeLa and Hep-2 cells. The pharmacological activity of diferent extracts showed sedative effect, slowing respiration, dose -dependent decrease in the arterial blood pressure by 40.1mm Hg (at adose 200mg /kg),decrease in the heart rate 67.3% (at a dose 50mg /kg)and decrease in the body temperature by 4.2C after 2 hrs (at a dose 200mg /kg). (author)

Energy Technology Data Exchange (ETDEWEB)

The present article describes a novel synthesis route for nano-sized goethite ({alpha}-FeOOH) using hydrazine sulphate as an additive. The X-ray diffraction (XRD) peaks of synthesized powder matched well with those of {alpha}-FeOOH. Transmission electron microscopy (TEM) showed the particles of irregular shape in the range of 1-10 nm. Batch adsorption experiments for fluoride uptake were performed to study the influence of various experimental parameters such as contact time (10 min to 7 h), initial fluoride concentration (10-150 mg L{sup -1}), pH (2-11.6) and the presence of competing anions. The time data fitted well to pseudo-second-order kinetic model. The fluoride removal passed through broad maxima in pH ranges of 6-8. High adsorption capacity of 59 mg g{sup -1} goethite was obtained. The isothermic data fitted well to Freundlich model. The presence of other ions namely chloride and sulphate adversely affected fluoride removal. Fluoride ...

International Nuclear Information System (INIS)

Certain 6000-series extrusions may develop susceptibility to intergranular corrosion (IGC) by improper heat treatment, especially if copper is present as an alloying element. Although occurrence of IGC in such cases is documented, the underlying mechanisms are not adequately explained. We present corrosion data for two model alloys, having different Cu content and Mg:Si ratio, showing that the susceptibility to IGC depended primarily on the Cu content and secondly on thermal processing. Low Cu samples (0.0005 wt.% Cu) were essentially resistant to IGC. High Cu samples (0.12 wt.% Cu), which were air cooled after extrusion, exhibited significant IGC. However, IGC susceptibility was reduced significantly as a result of artificial aging to peak strength. Water quenched high Cu samples were essentially resistant to IGC. However, slight IGC susceptibility was introduced after aging. Electron optical characterisation revealed Al_4Mg_8Si_7Cu_2 ...

British Library Electronic Table of Contents (United Kingdom)

Summary The purpose of this study was to evaluate the efficacy of postoperative adjuvant chemotherapy with FOLFOX regimen on the outcome after LT for HCC patients who did not meet the Milan criteria. Ninety-five consecutive HCC patients with liver cirrhosis undergoing LT were enrolled. Fifty-eight who did not meet the Milan criteria were randomized to open-label treatment with or without adjuvant chemotherapy after LT (n?=?29/group). The FOLFOX chemotherapy protocol comprised 3-week cycles of oxaliplatin 100?mg/m2 on day 1, leucovorin (calcium folinate, CF) 200?mg/m2 on day 1 followed by 3-day, and 5-fluorouracil (5-FU) 2000?mg/m2 as a 48-h continuous infusion, for up to six courses in the 1st year after transplantation. Median survival was extended by 4.57?months by combination chemothera...

International Nuclear Information System (INIS)

The aim of this study was to assess the body weight-tailored contrast material injection protocol for 64-detector computed tomography (CT) to maintain optimal coronary CT attenuation. A total of 60 patients who underwent CT coronary angiography were assigned to one of three groups: protocol A, total of 0.7 ml kg"-"1 with 300 mg I/ml iodine concentration; protocol B, total of 0.6 ml kg"-"1 with 350 mg I/ml; protocol C, total of 0.7 ml kg"-"1 with 350 mg I/ml. The injection duration was 10 s in all patients. The proportion of intracoronary attenuation values >325 Hounsfield unit (HU) was compared on a per-vessel and per-patient basis. The attenuation value was significantly more likely to exceed 325 HU with protocol C (95% for reader 1 and 90% for reader 2) than with protocol A or B on the per-vessel analysis (P325 HU) with 64-detector CT when using an injection duration of 10 s. (author)

British Library Electronic Table of Contents (United Kingdom)

The potential of the dried yeast, wild-type Schizosaccharomyces pombe, to remove Ni(II) ion was investigated in batch mode under varying experimental conditions including pH, temperature, initial metal ion concentration and biosorbent dose. Optimum pH for biosorption was determined as 5.0. The highest equilibrium uptake of Ni(II) on S. pombe, q e, was obtained at 25??C as 33.8?mg?g?1. It decreased with increasing temperature within a range of 25?50??C denoting an exothermic behaviour. Increasing initial Ni(II) concentration up to 400?mg?L?1 also elevated equilibrium uptake. No more adsorption took place beyond 400?mg?L?1. Equilibrium data fitted better to Langmuir model rather than Freundlich model. Sips, Redlich?Peterson, and Kahn isotherm equations modelled the investigated system with a...

Energy Technology Data Exchange (ETDEWEB)

Wastewater from a food-manufacturing plant with a low concentration of organic matter was treated at 37 centigrade in an anaerobic fluidized-bed reactor or in an upflow anaerobic sludge blanket. As the influent TOC (total organic carbon) concentration decreased, the TOC removal efficiency in these reactors decreased from 85% to 65%. The concentration of suspended solids in the effluent could be reduced to 20 mg/l, which corresponded to 7% of that in the influent. The effluent from both reactors was treated aerobically in a fixed-bed reactor. The TOC concentration and optical density of effluent from the aerobic treatment were reduced to 5 mg/l and 0.005, respectively. When the effluent treated anaerobically or aerobically was passed over an activated carbon column, the effluent TOC concentration was reduced to 2 to 3 mg/l. The conductivity in raw wastewater was remarkably reduced on an ion-exchange resin column. Ultra-pure ...

International Nuclear Information System (INIS)

To determine a rat strain appropriate for carcinogenicity testing of FYX-051, a xanthine oxidoreductase inhibitor, we performed a 4-week oral toxicity study by administering 0.3, 1 and 3 mg/kg, and 1, 3 and 10 mg/kg of FYX-051 to male Sprague-Dawley (SD) and Fischer (F344) rats, respectively. Histopathology revealed that the degree of FYX-051-induced nephropathy was 3-fold stronger in SD rats than in F344 rats. Our previous study demonstrated that the key factor of species differences in FYX-051-induced nephropathy is purine metabolism. This observation led us to examine the involvement of purine metabolism in differences among two strains of rats. However, purine metabolism was proven not to be implicated as an important factor. Subsequently, other factors responsible for the strain differences were examined. FYX-051-induced increases in plasma xanthine concentrations were higher in SD rats than in F344 rats, suggesting more remarkable effects ...

Energy Technology Data Exchange (ETDEWEB)

It is an object of the claimed invention to combine chemical treatment with microfiltration process to treat groundwater, leachate from contaminated soil washing, surface and run-off waters contaminated with toxic metals, radionuclides and trace amounts of organics from variety of sources. The process can also be used to treat effluents from industrial processes such as discharges associated with smelting, mining and refining operations. Influent contaminants amenable to treatment are from a few mg/L to hundreds of mg/L. By selecting appropriate precipitation, ion exchange and adsorption agents and conditions, efficiencies greater than 99.9 percent can be achieved for removal of contaminants. The filtered water for discharge can be targeted with either an order of magnitude greater or lower than contaminant levels for drinking water.

Energy Technology Data Exchange (ETDEWEB)

Improved biosorption of uranium by Kluyveromyces marxianus IMB3 biomass was achieved by increasing the electric field strength of delivered pulses from 1.25kV/cm to 2.5kV/cm. Although this had little or no effect on the maximum biosorption capacity (q(max)), at low concentrations of uranium the amount bound to the biomass increased from 70 to 140mg uranium/g biomass. Significant increases in the maximum biosorption capacities (119-180 mg uranium/g biomass) were observed when the pulse field strength was increased from 2.5kV/cm to 3.25kV/cm. (Author).

British Library Electronic Table of Contents (United Kingdom)

This study describes the chemical composition of the essential oil of Artemisia maritima (Am.Oil) and the pharmacological basis for its medicinal use in gut and airways disorders. Twenty five compounds, composing 93.7% of the oil, were identified; among these, chrysanthenyl propionate and elixene were identified for the first time from any Artemisia species. The Am.Oil (0.3?1.0 mg/mL) suppressed spontaneous and high K+ (80 mM)-induced contractions in isolated rabbit jejunum, suggestive of an antispasmodic effect mediated possibly through calcium channel blockade. The calcium channel blockade activity was confirmed when pre-treatment of the tissue with Am.Oil (0.01?0.03 mg/mL) shifted the Ca++ concentration-response curves to the right, similar to verapamil and papaverine. In isolated trach...

British Library Electronic Table of Contents (United Kingdom)

Changes in cell density and cyst flux of Alexandrium tamarense, paralytic shellfish poisoning (PSP) toxin contents in shellfishes, and environmental parameters were measured in two stations in Daya Bay, South China Sea from March 2005 to July 2006. Vegetative cells of A. tamarense occurred sporadically; however, they presented abundantly during the winter months. Meanwhile, cyst flux reached its maximum level just following the peak abundance of motile cells. The PSP contents in shellfish were generally low, but higher in winter with the maximum of 14,015 @mg STX equiv./kg. The majority of toxins were found in digestive glands, with a maximum of 66,227 @mg STX equiv./kg. There were significant positive relationships between toxin level and vegetative cell density and cyst flux. This indica...

Energy Technology Data Exchange (ETDEWEB)

The effect of Al/sup 3 +/, Fe/sup 3 +/, Ca/sup 2 +/, and Mg/sup 2 +/ ions and of pH on the two-dimensional shear modulus of stearic acid spread on a water substrate was determined. A large shear modulus was displayed by the films when the subphase contained Al/sup 3 +/ and Fe/sup 3 +/ ions at the self-buffered pH. With Fe/sup 2 +/ dissolved in the subphase, the film displayed a viscous relaxation when strained but no residual stress was observed. No effect was observed with the Ca/sup 2 +/ or Mg/sup 2 +/. Reducing the pH value in the subphase with the trivalent ions caused the shear modulus to disappear. The observations are interpreted in terms of hydrogen bonding.

British Library Electronic Table of Contents (United Kingdom)

Bungarus caeruleus (Indian common krait) bite during monsoons is common in Northwest India. This study was undertaken to find the effectiveness of neostigmine and polyvalent antivenom in improving neuromuscular paralysis following bite. All the consecutive patients admitted between June 2007 and December 2008 with common krait bite, identified either from brought snake or circumstantial evidence were studied. Ten vials of polyvalent antivenom and three doses of 2.5mg neostigmine at 30min intervals after administration of 0.6mg of atropine were administered I.V. and patients were assessed for any improvement in neuroparalysis. Seventy-two patients were admitted during the study period. All the patients except two came from rural areas and were brought between June and September. Sixty-two p...

British Library Electronic Table of Contents (United Kingdom)

The effects of oral administration of aqueous extract of Bulbine natalensis Baker stem at daily doses of 25, 50, and 100mg/kg body weight on the reproductive function of Wistar rats were evaluated. The indices of mating and fertility success as well as quantal frequency increased after 7 days of treatment in all the dose groups except the 100mg/kg body weight group. The number of litters was not statistically different (P>0.05) from the control. Whereas the absolute weights of the epididymis, seminal vesicle, and prostate were not affected, that of the testes was significantly increased. The epididymal sperm count, motility, morphology, and viscosity were not different from the control after 7 days of treatment. The male rat serum testosterone, progesterone, luteinizing hormone, and follic...

Energy Technology Data Exchange (ETDEWEB)

A sample of 30 manganese-exposed foundry workers from two Swedish plants were examined with a partly computerized psychological test battery, comprised of 10 performance tests. Performance of the manganese-exposed workers was compared to that of a matched control group of 60 workers. Matching criteria were age, geographical area, type of work, and the results on a test of verbal comprehension. Performance of the exposed workers was inferior to that of the control group on tests of simple reaction time, digit span, and finger tapping. No correlations were found between performance and the present manganese exposure levels or the number of years employed in manganese work. The results seem to indicate that the present exposure standards for manganese, in Sweden 2.5 mg/m3 and in most other countries 5 mg/m3, are not sufficient to protect workers from negative effects on performance capacity.

British Library Electronic Table of Contents (United Kingdom)

Objectives To delineate the safety and tolerability profile of methylphenidate and atomoxetine in children and adolescents with attention deficit hyperactivity disorder (ADHD) monitored for more than 1?year. Design A cohort study analyzing data from the national ADHD register on patients from the Lombardy Region treated with MPH or atomoxetine. Participants A total of 229 children (median age 11?years, range 6?17), enrolled in 15 regional centers between June 2007 and May 2010. Results The prevalence rate of pharmacological treatment for ADHD was 0.23%, whereas the estimated ADHD prevalence in the population was 0.95%. In total, 73.8% of patients had been treated with atomoxetine (10?90?mg daily) or MPH (10?75?mg daily); 22% of patients also received an additional psychotropic drug. Of the...

International Nuclear Information System (INIS)

Multi-core MgB_2/Ti/Cu/SS composite wire has been made by the in situ approach. Mechanical properties, interdiffusion reactions and critical currents were studied after heat treatments at temperatures between 500 and 850 "0C. Cu diffusion into the Ti layer occurs for all samples, resulting in the formation of intermetallic compounds at the Cu/Ti interface. EDX analysis has revealed the temperature dependence of all interface reactions. In spite of element reactions the critical current densities 10"5 A cm"-"2 and 10"4 A cm"-"2 were measured in liquid helium at magnetic fields 5 T and 9.5 T, respectively. 10"4 A cm"-"2 at 20 K is measured in an external field of 4 T.

Energy Technology Data Exchange (ETDEWEB)

Fischer-344 rats were exposed to quartz dusts and to quartz-bearing oil shale dusts in long-term inhalation studies. Aerosol concentrations of 12 mg/m/sup 3/ and 152-176 mg/m/sup 3/ for quartz and shale dusts, respectively, were used in exposure regimens lasting up to two years. Pulmonary fibrosis was observed in most animals surviving beyond 400 days. Adenocarcinomas and epidermoid carcinomas of the lung were observed in animals from all exposure groups, including those exposed to quartz alone. The pulmonary tumors were a late effect, with the earliest lung tumor being observed after 651 days. 13 references, 10 figures, 4 tables.

Science.gov (United States)

Effective localization of small magnets against a noisy, real world background can involve various methods to first identify the magnetic fields produced by the magnet of interest, then to filter out background noise, and then to analyze the available magnetic field data to localize the magnet. Here we discuss low cost techniques which allow localization of small magnets with field strengths in the milliGauss range against real world background fields in the range of hundreds of mG, which may be fluctuating by up to tens of mG. Such techniques allow magnet tracking to be used to localize catheters in place of more invasive and expensive methods, e.g. fluoroscopy, for a variety of applications, including drug infusion with peripherally inserted central catheters (PICCs), laser ablation (TMR, PTMR) and introduction of pacemaker leads.

British Library Electronic Table of Contents (United Kingdom)

Aim of the study: Satureja montana (winter savory) is a medicinal plant traditionally used to treat different disorders including male sexual dysfunction. In this study we evaluated the effect of Satureja montana hydroalcoholic extract on copulatory behavior of sexually potent male rats. Materials and methods: The extract was orally administered acutely or repetitively for 8 consecutive days at the doses of 25 and 50mg/kg. The main parameters of sexual behavior, mount (ML), intromission (IL), ejaculation (EL) latencies and post-ejaculatory interval (PEI), were evaluated in animals submitted to mating test and multiple ejaculations test. Testosterone serum levels were measured in rats acutely treated with Satureja montana extract dosed at 50mg/kg. In addition the open field test was conduct...

British Library Electronic Table of Contents (United Kingdom)

Ochratoxin A (OTA) was analyzed from 44 liquorice confectionery samples using immunoaffinity cleanup and liquid chromatography coupled with fluorescence detection. The presence of OTA was confirmed by methyl-ester derivatization. Liquorice confectionery samples were purchased from different retail outlets and supermarkets in Spain during 2007-2008, 16 of hard candies and 28 of soft candies. The incidence of OTA varied between 75% and 39% and mean ranged from 2.96 to 0.34mg/kg for hard and soft candies, respectively. Assuming a total mean value of 1.29mgOTA/kg sweet and a consumption of about 1.2g liquorice sweets per day, an OTA weekly uptake of 11ng was obtained, or, based on a total body weight of 30kg for a child consuming these sweets regularly, a weekly intake of 0.37ng/kg body weight...

British Library Electronic Table of Contents (United Kingdom)

The growth response, total hemocyte count (THC), respiratory burst (release of superoxide anion), phenoloxidase (PO) activity, superoxide dismutase (SOD) activity, nitric oxide synthase (NOS) activity as well as resistance to the pathogen Vibrio alginolyticus were measured in Litopenaeus vannamei, which had been fed diets supplemented with glycyrrhizin (the aqueous extract of licorice, Glycyrrhiza glabra, roots) at 0, 50, 100, 150, and 200 mg/kg of feed for 8 wk. In the feeding trial, there was no significant difference in survival rate (P > 0.05). Significant higher specific growth rate was observed in treatments with dietary glycyrrhizin than that in the control group (P < 0.05). Shrimp fed a diet with 200 mg/kg of glycyrrhizin had significant higher THC, PO activity, respiratory burst a...

Energy Technology Data Exchange (ETDEWEB)

Stoichiometric MgAl{sub 2}O{sub 4} spinel specimens irradiated in FFTF-MOTA at temperatures between 385 and 750C to fluences ranging from 2.2 to 24.9 {times} 10{sup 22}n cm{sup {minus}2} (E>0.1 MeV) darken significantly, but do not develop any significant loss in weight or change in dimensions. Similar behavior was observed in both single crystal and fully dense polycrystalline specimens. Measurements of elastic constants by an ultrasonic technique show that no measurable changes occur as a result of the irradiation. These and other results confirm the stability of this material for fusion application as an electrical insulator.

International Nuclear Information System (INIS)

The energy levels scheme of octahedrally coordinated Ni2+ ion in single crystal, powder nano-single crystal, ceramics and glass-ceramics of MgGa2O4 host matrix, has been calculated in the exchange charge model of crystal field. The parameters of the crystal field acting on the Ni2+ ion are calculated from the crystal structure data, after optimization of the geometry of the system. The energy level schemes have been calculated by diagonalization of the crystal field Hamiltonian of this system. The obtained results were compared with experimental data; a good agreement were demonstrated, which confirm the validity of the model and used method.

Energy Technology Data Exchange (ETDEWEB)

We have developed a low-temperature particle detector that uses a novel quasiparticle trapping mechanism to funnel athermal phonon energy from an 80 mg Ge absorber into a 1.6 mg doped Ge thermistor via a superconducting Al film. We report on pulse height spectra obtained at 320 mK by scanning a {sup 241}Am alpha source along the device, and show that up to 20% of the energy deposited in the Ge absorber by a 5.5 MeV alpha particle interaction can be collected into a thermistor via quasiparticle trapping. We show that this device is sensitive to the position of an alpha particle interaction in the Ge absorber for interaction distances of up to 5 mm from a quasiparticle trap.

British Library Electronic Table of Contents (United Kingdom)

In this study, bacterial strains were investigated in order to determine their heavy metal tolerance. The bacterial strains were identified as Bacillus cereus and Bacillus pumilus. In the batch system, the effects of operating variables such as solution pH, initial metal concentration, contact time, and adsorbent dosage were investigated. Both isolates were highly resistance to copper and lead in comparison with the control strain examined. The adsorption capacities of B. cereus and B. pumilus were found to be 22.1mg/g and 28.06mg/g, respectively. The biosorption follows pseudo-second order kinetics and the isotherm fits well to the Langmuir isotherm model. In column experiments, the biosorption was fitted well by the Thomas model. The breakthrough and exhaustion capacity of each biosorben...

British Library Electronic Table of Contents (United Kingdom)

The methanol and aqueous extracts of 10 plant species (Acacia nilotica, Azadirachta indica, Carissa edulis, Fagaropsis angolensis, Harrissonia abyssinica, Myrica salicifolia, Neoboutonia macrocalyx, Strychnos heningsii, Withania somnifera and Zanthoxylum usambarensis) used to treat malaria in Meru and Kilifi Districts, Kenya, were tested for brine shrimp lethality and in vitro anti-plasmodial activity against chloroquine-sensitive and chloroquine-resistant strains of Plasmodium falciparum (NF54 and ENT30). Of the plants tested, 40% of the methanol extracts were toxic to the brine shrimp (LD5050N. macrocalyx had the highest toxicity to brine shrimp nauplii (LD50 21.04+-1.8mg/ml). Methanol extracts of the rest of the plants exhibited mild or no brine shrimp toxicity (LD50>50mg/ml). The aqueo...

Energy Technology Data Exchange (ETDEWEB)

Our Andreev reflection measurements (Phys. Rev. Lett. 87 (2001) 137005) along with other experiments have led to a general consensus that MgB{sub 2} is a multiband superconductor with two main superconducting gaps closing at the same T{sub c}. Here we show the behavior of the small gap as a function of the temperature and magnetic field. This gap is isotropic with T{sub c} of the bulk material but with a specific small (crossover) critical magnetic field of about 1 T much lower than the real H{sub c2}. The latter field is anisotropic and is rather governed by the large gap and strongly anisotropic Fermi surface of the material.

Energy Technology Data Exchange (ETDEWEB)

Experimental wetlands are being constructed on mined lands in the United States as an inexpensive alternative to conventional acid mine water treatment facilities. The US Bureau of Mines is conducting an inventory of these constructed wetlands as part of a long-term evaluative study. Preliminary results, based on the 20 sites surveyed to date, indicate that the wetlands dominated by emergent species are out-performing the Sphagnum-dominated wetlands, and that much of the water treatment is accomplished by other aspects of the wetland, including bacteria, algae, amendments and other plants. Iron concentrations as high as 85 mg/l are reduced to less than 3 mg/l after flow through the constructed wetlands. Manganese is also removed, though somewhat less efficiently. 12 refs., 1 fig., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...

International Nuclear Information System (INIS)

Environmental factors, phytoplankton biomass (Chl a) and primary production of two water areas in Daya Bay (Dapeng'ao Bay and Aotou Bay) were investigated during the transition period from spring to summer. Chl a ranged from 3.20 to 13.62 and 13.43 to 26.49 mg m"-"3 in Dapeng'ao Bay and Aotou Bay respectively, if data obtained during red tides are excluded. Primary production varied between 239.7 and 1001.4 mgC m"-"2 d"-"1 in Dapeng'ao Bay. The regional distribution of Chl a and primary production were mostly consistent from spring to summer in both bays. Seasonal transition characters have been found in Daya Bay from spring to summer, including high values of DO, nitrate and silicate. Size structures of phytoplankton and its primary production do not change very much from spring to summer, with micro-phytoplankton dominating and contributing about 50% of the whole. In Daya Bay, phytoplankton is limited by nitrogen in spring, and by phosphate ...

International Nuclear Information System (INIS)

The oxygen vacancies distribution in the rigid lattice and the thermally activated motion of oxygen atoms are studied in La1-xSrxGa1-xMgxO3-x (x=0.00; 0.05; 0.10; 0.15 and 0.20) compounds. For that 71Ga, 25Mg and 17O NMR was performed from 100 K up to 670 K, and ion conductivity measurements were carried out up to 1273 K. The comparison of the electric field gradients at the Ga- and Mg-sites evidences that oxygen vacancies appear exclusively near gallium cations as a species trapped below room temperature in local clusters, GaO5/2-#square#-GaO5/2. These clusters decay at higher temperature into mobile constituents of the structural octahedra Ga(O5/6#square#1/6)6/2. At the same time, the nearest octahedral oxygen environment of magnesium cations persists at different doping levels. The case of two adjacent vacant anion sites is found highly unlikely within the studied doping range. The thermally activated oxygen motion starts to develop above ...

UK PubMed Central (United Kingdom)

1. From a 150 mM-NH4 salicylate medium salicylate enters human red cells with a rate constant of 1.9 min-1 at 0 degrees C. 2. Salicylate increases the red cell permeability for Ca2+ (and Mg2+). There...Full Text Available

UK PubMed Central (United Kingdom)

A soluble enzyme system from suspension cultures of Acer pseudoplatanus L. converts d-glucose 6-phosphate to myoinositol. A Mg²⁺-dependent phosphatase, present in...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The first study in this dissertation describes the development of a suppressed ion chromatographic (SIC) technique for the direct, simultaneous determination of the As and Se oxyanions in soil solution. Baseline resolution of 1 mg L[sup [minus]1] each of arsenite, arsenate, selenite, and selenate was achieved in the presence of 50 mg L[sup [minus]1] each of F, Cl, NO[sub 3]-N, SO[sub 4]-S, and PO[sub 4]-P. Detection limits ranged from 0.026 mg L[sup [minus]1] for selenite to 0.120 mg L[sup [minus]1] for arsenate. The accuracy of the SIC technique was verified by comparison to spectroscopic methods. The second study investigated the suitability of linear-plateau regression analysis for statistical evaluation of As adsorption data. The time required to reach the adsorption plateau depended on soil characteristics and As species. Identification of the adsorption plateau by the linear-plateau model allowed ...

International Nuclear Information System (INIS)

An internuclear cascade-evaporation code is used to model energy deposition in thin slabs of silicon. This model shows that protons produce a significant number of events with effective Linear Energy Transfer (LET) greater than 8 MeV cm"2/mg and demonstrates that proton testing of microelectronic components can be an effective way to screen devices for low earth orbit susceptibility to heavy ions.

Science.gov (United States)

1. Choline, and the choline analogues monoethylcholine (MEC) and N-aminodeanol (NAD) were examined for prophylactic activity in acute acetylcholinesterase inhibitor toxicity in mice. The rank order of potency of the compounds was MEC greater than NAD greater than choline. 2. Simultaneous administration of MEC (60 mg kg-1) or NAD (200 mg kg-1) with physostigmine reduced lethality to 17 and 13% respectively. MEC (60 mg kg-1) completely protected against disopropylfluorophosphate (DFP) and diazinon toxicity, and NAD reduced lethality to 17% for both agents. Choline (200 mg kg-1) exhibited only negligible antidotal activity against the inhibitors. 3. In vitro concentrations of choline, MEC, and NAD, similar to the estimated concentration obtained in vivo in the acute toxicity study, produced mixed inhibition of mouse brain acetylcholinesterase. The inhibition was dose-related and was additive to the ...

Energy Technology Data Exchange (ETDEWEB)

A focused ion beam (FIB) system has been applied to prepare a thin foil specimen of Si, MgO and alumina which contained cracks in the plan of foil. It was possible to observe a much larger area at and near a crack tip than has been hitherto possible. FIB was also applied to observation of microstructure near a crack tip evolved during severe rolling contact fatigue in a steel.

International Nuclear Information System (INIS)

Here we report normal-state conductance measurements of three different types of superconducting tunnel junctions that are being used or proposed for quantum computing applications: p-Al/a-AlO/p-Al, e-Re/e-AlO/p-Al, and e-V/e-MgO/p-V, where p stands for polycrystalline, e for epitaxial, and a for amorphous. All three junctions exhibited significant deviations from the parabolic behavior predicted by the WKB approximation models. In the p-Al/a-AlO/p-Al junction, we observed enhancement of tunneling conductances at voltages matching harmonics of Al-O stretching modes. On the other hand, such Al-O vibration modes were missing in the epitaxial e-Re/e-AlO/p-Al junction. This suggests that absence or existence of the Al-O stretching mode might be related to the crystallinity of the AlO tunnel barrier and the interface between the electrode and the barrier. In the e-V/e-MgO/p-V junction, which is one of the candidate systems for future superconducting ...

International Nuclear Information System (INIS)

In January 1994, a 6.7 magnitude earthquake in southern California ruptured a pipeline releasing approximately 4,200 barrels of blended San Joaquin Valley crude oil. A smaller volume entered the Santa Clara River and flowed 25 km downstream to an emergency containment dam. Ruptured water mains and chlorinated discharges from a damaged sewage treatment plant also affected water quality in the river. Quantitative injury assessment studies were initiated within days of the spill and included water/sediment chemistry, benthic macroinvertebrate community analyses and aquatic toxicity tests. Water quality values for TPH, BTEX, and chlorine ranged from nondetectable to 78 mg/l (TPH), nondetectable to 5.4 microg/l (total BTEX constituents) and nondetectable to 600 microg/l (residual chlorine) within 72 hours of the spill. Ammonia concentrations ranged from nondetectable to 12.1 mg/l within 10 days of the spill. Hydrocarbon concentrations in sediments ...

International Nuclear Information System (INIS)

The upper range of the requirement for methionine plus cystine in healthy adults was proposed in 1985 by FAO/WHO/UNU to be 13 mg.kg body wt-1.d-1. To explore the validity of this estimate, five healthy, young adult men were given for 7 d a diet based on an L-amino acid mixture supplying 13 mg methionine.kg-1.d-1 (87 mumol.kg-1.d-1) without cystine. Constant intravenous infusions of L-[2H3-methyl-1-13C]methionine were given on days 5 and 7 while subjects were in the fed and postabsorptive states, respectively. Estimates were made of methionine oxidation, and daily methionine balance was derived from the intake-oxidation data. For the five subjects, methionine balances were -0.9, +0.7, +3.5, -3.1, and -3.8 mg kg-1.d-1, or -6, +5, +23, -21, and -26 mumol.kg-1.d-1. These findings lead to the conclusion that the upper range of the requirement for methionine plus cystine probably exceeds 13 mg.kg-1.d-1 in ...

International Nuclear Information System (INIS)

It was shown that the incorporation of "1"4C-linoleic acid in cerebrosides of normal and psoriatic human skin is different. In psoriatic epidermis and corium the turnover of this fatty acid is significantly elevated. It is suggested that in psoriasis the epidermal cell is not able to build up a regular carbohydrate sequences of lipids because the false carbohydrate chain activates the degradation of glycolipids and in compensating for the increased degradation raises the synthesis rate of glycolipids. (orig./MG).

UK PubMed Central (United Kingdom)

Outbred Wistar rats were immunised with a single intraperitoneal injection of a mixture of 30 mg of A1(OH)3 and 100microng of gonococcal zeolite antigen (ZA). Ten days after immunisation, ZA prepared...Full Text Available

International Nuclear Information System (INIS)

Ultra low loading noble metal (0.04-0.12 mg_P_t/cm"2) based electrodes were obtained by direct metallization of non-catalyzed gas diffusion layers via dual ion beam assisted deposition (IBAD) method. Fuel cell performance results reported earlier indicate significant improvements in terms of mass specific power density of 0.297 g_P_t/kW with 250 A thick IBAD deposit (0.04 mg_P_t/cm"2 for a total MEA loading of 0.08 mg_P_t/cm"2) at 0.65 V in contrast to the state of the art power density of 1.18 g_P_t/kW using 1 mg_P_t_(_M_E_A_)/cm"2 at 0.65 V. In this article we report the peroxide radical initiated attack of the membrane electrode assembly utilizing IBAD electrodes in comparison to commercially available E-TEK (now BASF Fuel Cell GmbH) electrodes and find the pathway of membrane degradation as well. A novel segmented fuel cell is used for this purpose to relate membrane degradation to peroxide ...

UK PubMed Central (United Kingdom)

1. Ro 15-8081 (Hoffmann-La Roche, Basle, Switzerland) is a novel mixed 5-HT/noradrenaline uptake inhibitor producing potent antinociceptive effects in animal pain models. 2. In healthy man, two models...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The effect of 10 wk endurance swim training on 3-O-methylglucose (3-MG) uptake (at 40 mM 3-MG) in skeletal muscle was studied in the perfused rat hindquarter. Training resulted in an increase of approximately 33% for maximum insulin-stimulated 3-MG transport in fast-twitch red fibers and an increase of approximately 33% for contraction-stimulated transport in slow-twitch red fibers compared with nonexercised sedentary muscle. A fully additive effect of insulin and contractions was observed both in trained and untrained muscle. Compared with transport in control rats subjected to an almost exhaustive single exercise session the day before experiment both maximum insulin- and contraction-stimulated transport rates were increased in all muscle types in trained rats. Accordingly, the increased glucose transport capacity in trained muscle was not due to a residual effect of the last training session. Half-times for reversal of ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys and composites are potentially highly attractive materials for lightweight design in the automotive industry - if common forming technologies, i.e., deep drawing and cold extrusion, are applicable to them; so far, this is seldom the case. The authors have tested some candidate Mg alloys and discuss the results of their measurements in detail. The Figure shows a typical workpiece part obtained by a deep-drawing technique. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

This study presents and applies a coherent methodological framework to compare biomass cascading chains, i.e. the subsequent use of biomass for materials, recycling and energy recovery, considering land use, CO2 emission reduction and economic performance. Example cascading chains of short rotation poplar wood are compared with each other on the basis of literature data. Results for these chains vary strongly, namely, from CO2 mitigation benefits of 200 euro/Mg CO2 to CO2 mitigation costs of 2200 euro/Mg CO2, and from net CO2 emission reductions per hectare of biomass production of 28 Mg CO2/(ha yr) to net CO2 emissions of 8 Mg CO2/(ha yr). Using a present-value approach to determine CO2 emissions and costs affects the performance of long-term cascading chains significantly, i.e. cost and CO2 emission reduction are decreased. In general, cascading has the potential to improve both CO2 emission reduction ...