Energy Technology Data Exchange (ETDEWEB)

A fuel cycle economic analysis was performed on four fuel cycles to provide a baseline for initial cost comparison using the Gen IV Economic Modeling Work Group G4 ECON spreadsheet model, Decision Programming Language software, the 2006 Advanced Fuel Cycle Cost Basis report, industry cost data, international papers, the nuclear power related cost study from MIT, Harvard, and the University of Chicago. The analysis developed and compared the fuel cycle cost component of the total cost of energy for a wide range of fuel cycles including: once through, thermal with fast recycle, continuous fast recycle, and thermal recycle.

Energy Technology Data Exchange (ETDEWEB)

A unified model is presented for a class of combined energy systems, in which the systems mainly consist of a heat engine, a combustor and a counter-flow heat exchanger and the heat engine in the systems may have different thermodynamic cycle modes such as the Brayton cycle, Carnot cycle, Stirling cycle, Ericsson cycle, and so on. Not only the irreversibilities of the heat leak and finite-rate heat transfer but also the different cycle modes of the heat engine are considered in the model. On the basis of Newton's law, expressions for the overall efficiency and power output of the combined energy system with an irreversible Brayton cycle are derived. The maximum overall efficiency and power output and other relevant parameters are calculated. The general characteristic curves of the system ...

Energy Technology Data Exchange (ETDEWEB)

In recent years the modelling of interannual climate variability has been studied, the atmospheric energy and water cycles, and climate simulations with the ECHAM3 model. In addition, the climate simulations of several models have been compared with special emphasis in the area of northern Europe

Energy Technology Data Exchange (ETDEWEB)

During the last 15 years cycles with CO{sub 2} capture have been in focus, due to the growing concern over our climate. Often, a natural gas fired combined cycle with a chemical absorption plant for CO{sub 2} capture from the flue gases have been used as a reference in comparisons between cycles. Neither the integration of the steam production for regeneration of amines in the combined cycle nor the off-design behaviour of such a plant has been extensively studied before. In this paper, the integration of steam production for regeneration of the amines is modelled at design load and studied in off-design conditions for a combined cycle. Different ambient conditions and part-load strategies and their influence on the cycle performance are also examined. Of particular interest is a novel strategy with the possibility of longer life of gas ...

Science.gov (United States)

... of electronic systems (satellite terminals, radio and ... helps organizations investigate the stochastic nature of ... cycle time, maximum queue lengths, and ...

Energy Technology Data Exchange (ETDEWEB)

The goal of this DOE Vision-21 project work scope is to develop an integrated suite of software tools that can be used to simulate and visualize advanced plant concepts. Existing process simulation software does not meet the DOE's objective of ''virtual simulation'' which is needed to evaluate complex cycles. The overall intent of the DOE is to improve predictive tools for cycle analysis, and to improve the component models that are used in turn to simulate the cycle. Advanced component models are available; however, a generic coupling capability that will link the advanced component models to the cycle simulation software remains to be developed. In the current project, the coupling of the cycle analysis and cycle component simulation software will be ...

CERN Document Server

The determinants of the velocity of money have been examined based on life-cycle hypothesis. The velocity of money can be expressed by reciprocal of the average value of holding time which is defined as interval between participating exchanges for one unit of money. This expression indicates that the velocity is governed by behavior patterns of economic agents and open a way to constructing micro-foundation of it. It is found that time pattern of income and expense for a representative individual can be obtained from a simple version of life-cycle model, and average holding time of money resulted from the individual's optimal choice depends on the expected length of relevant planning periods.

International Nuclear Information System (INIS)

Simple hydroxamic acids are shown to be useful reagents for the separation of Np and Pu from U within simplified, single cycle Purex flowsheets. They are compatible with the use of centrifugal contactors and laboratory scale flowsheet trials with aceto-hydroxamic acid have demonstrated high actinide recoveries and decontamination factors on products for active feeds of up to 40 wt.% Pu. They therefore show many ideal characteristics for Pu and Np recovery within flowsheet options for actinide recovery in advanced fuel cycles. Furthermore, in order to optimise the routing of Np with the Pu product in advanced flowsheets, additional studies of Np extraction in the primary co-decontamination contactor, prior to U/Pu partition, have been undertaken, combining experiment, modelling and flowsheet tests. (author)

International Nuclear Information System (INIS)

This third tome about energy systems completes the two previous ones by showing up advanced thermodynamical cycles, in particular having a low environmental impact, and by dealing with two other questions linked with the study of systems with a changing regime operation: - the time management of energy, with the use of thermal and pneumatic storage systems and time simulation (schedule for instance) of systems (solar energy type in particular); - the technological dimensioning and non-nominal regime operation studies. Because this last topic is particularly complex, new functionalities have been implemented mainly by using the external classes mechanism, which allows the user to freely personalize his models. This tome is illustrated with about 50 examples of cycles modelled with Thermoptim software. Content: foreword; 1 - generic external classes; 2 - advanced gas turbine cycles; 3 ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the development and use of the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The model, developed in a spreadsheet format, estimates the full fuel- cycle emissions and energy use associated with various transportation fuels for light-duty vehicles. The model calculates fuel-cycle emissions of five criteria pollutants (volatile organic compounds, carbon monoxide, nitrogen oxides, sulfur oxides, and particulate matter measuring 10 microns or less) and three greenhouse gases (carbon dioxide, methane, and nitrous oxide). The model also calculates the total fuel-cycle energy consumption, fossil fuel consumption, and petroleum consumption using various transportation fuels. The GREET model includes 17 fuel cycles: petroleum to conventional ...

UK PubMed Central (United Kingdom)

PurposeHyperglycemia and hypertension contribute to the development of diabetic retinopathy, and this may involve alterations in the normal retinal cell cycle. In this work, we examined...Full Text Available

International Nuclear Information System (INIS)

This paper examines cupric chloride solid conversion during hydrolysis in a thermochemical copper-chlorine (Cu-Cl) cycle for hydrogen production. The hydrolysis reaction is a challenging step, in terms of the excess steam requirement and the decomposition of cupric chloride (CuCl_2) into cuprous chloride (CuCl) and chlorine (Cl_2). The hydrolysis and decomposition reactions are analyzed with respect to the chemical equilibrium constant. The effects of operating parameters are examined, including the temperature, pressure, excess steam and equilibrium conversion. A maximization of yield and selectivity are very important. Rate constants for the simultaneous reaction steps are determined using a uniform reaction model. A shrinking core model is used to determine the rate coefficients and predict the solid conversion time, with diffusional and reaction control. These new results are useful for scale-up of the engineering ...

Energy Technology Data Exchange (ETDEWEB)

The physics of density limit phenomena in toroidal helical plasmas based on an analytic point model of toroidal plasmas is discussed. The combined mechanism of the transport and radiation loss of energy is analyzed, and the achievable density is derived. A scaling law of the density limit is discussed. The dependence of the critical density on the heating power, magnetic field, plasma size and safety factor in the case of L-mode energy confinement is explained. The dynamic evolution of the plasma energy and radiation loss is discussed. Assuming a simple model of density evolution, of a sudden loss of density if the temperature becomes lower than critical value, then a limit cycle oscillation is shown to occur. A condition that divides the limit cycle oscillation and the complete radiation collapse is discussed. This model seems to explain the density limit oscillation that has been ...

Energy Technology Data Exchange (ETDEWEB)

A numerical model has been developed to simulate the charging and discharge behaviour of an electrically rechargeable alkaline zinc-air battery. Further a galvanostatic experiment including three charge/discharge cycles has been performed. The cell voltages, the Zn electrode potentials versus a Zn reference, and the O{sub 2} electrode potentials versus a Zn reference calculated with the model are in fairly good agreement with the corresponding experimental data. The model is expected to be useful for zinc-air battery design and for analysis of experimental data. (author)

Energy Technology Data Exchange (ETDEWEB)

Protein motions on all timescales faster than molecular tumbling are encoded in the spectral density. The dissection of complex protein dynamics is typically performed using relaxation rates determined at high and ultra-high field. Here we expand this range of the spectral density to low fields through field cycling using the nucleocapsid protein of the SARS coronavirus as a model system. The field-cycling approach enables site-specific measurements of R{sub 1} at low fields with the sensitivity and resolution of a high-field magnet. These data, together with high-field relaxation and heteronuclear NOE, provide evidence for correlated rigid-body motions of the entire {beta}-hairpin, and corresponding motions of adjacent loops with a time constant of 0.8 ns (mesodynamics). MD simulations substantiate these findings and provide direct verification of the time scale and collective nature of these motions.

Energy Technology Data Exchange (ETDEWEB)

A phenomenological model of turbulent combustion has been developed and validated against data from wide ranging tests on a Ricardo E6 engine. Most tests used iso-octane, with a range of air fuel ratios and ignition timings, for tests at full throttle (with and without knock) and at part throttle. Some full throttle tests were also conducted with methanol and toluene. The engine performance was characterized by mean and coefficient of variation (CoV) of: the peak pressure, the maximum rate of pressure rise, the IMEP, the burn rate and flame speed measurements. The results have been used to argue that the cycle-by-cycle variations in combustion should be characterized by the CoV of IMEP in preference to the CoV of the maximum cylinder pressure. Evidence is also presented to support the observation that the cycle-by-cycle variations in combustion are lower when the early combustion is more rapid. It has also been shown that ...

Energy Technology Data Exchange (ETDEWEB)

A new performance model of the externally fired combined cycle (EFCC) is implemented in ASPEN (Advanced System for Process ENgineering), a chemical process simulator. The model accounts for interactions within and between approximately a dozen major process areas. The new model is applied to case studies to evaluate the sensitivity of process performance to the ranges of uncertainty in key model inputs such as heat losses, carbon conversion, and air leakage rates, and to illustrate how alternative designs, including steam injection and flue gas desulfurization (FGD), can affect plant thermal efficiency and net power output. The model results suggest that careful attention to the design of the FGD system is needed, especially with respect to reheat, and that steam injection may offer cost savings associated with reducing the size of the steam turbine with little ...

Energy Technology Data Exchange (ETDEWEB)

Thermal striping is identified as one of the causes of thermal fatigue failure in nuclear power plants. Numerical studies of thermal striping require three-dimensional, unsteady turbulent modeling that resolves both large and small-scale turbulent motions. Benchmark studies were carried out using the LES turbulence model solved by the commercial CFD code FLUENT. Two types of mixing tee configurations were modeled to evaluate the performance of the CFD code. The simulation results presented in normalized average temperature and normalized fluctuating temperatures are in good agreement with measurements.

Environmental Research Database

Objectives(i) Investigate the correlation between Antarctic sea-ice and equatorial sea-surface temperature anomalies in a realistically forced ocean model simulation of the last 50 years. (ii) Determine whether and how the enormous seasonal change in distribution of sea-ice modifies the seasonal cycle at the Equator. (iii) Determine the detailed pathways of wave propagation both in a historically-forced simulation and in response to realistic perturbations. (iv) Quantify the amplitude of the response i [continued...]DescriptionIt is well known that the equatorial ocean-atmosphere system plays a key role in global climate events such as the El Nino-Southern Oscillation (ENSO) phenomenon. There is now compelling evidence that changes in the Antarctic can strongly and quickly affect the equatorial ocean and the ENSO cycle. Observations demonstrate statistically significant correlations (teleconnections) between the Antarctic ...

British Library Electronic Table of Contents (United Kingdom)

Durability is a major limitation of current proton exchange membrane fuel cells. Mechanical stress due to hygro-thermal cycling is one failure mechanism of the polymer electrolyte membrane. In previous work the cyclic rate, temperature, and hydration dependent elastic-viscoplastic mechanical behavior of Nafion has been extensively investigated in uniaxial and biaxial tension, serving as a data basis and means of validation for a three-dimensional constitutive model. Here, the important effect of loading via constrained swelling is studied. Specifically, two types of loading are investigated: partially constrained swelling via a bimaterial swelling test and hygro-thermal cycling within a fuel cell. The bimaterial swelling conditions are examined via experiments in conjunction with modeling....

International Nuclear Information System (INIS)

Australian electricity markets and natural gas markets are undergoing rapid reform. Choosing among electricity generation modes is a key issue. Such choices are affected by expectations about the future structure of these markets and future technologies, and how they affect costs and emissions. In the research reported in this paper, the MARKAL model of the Australian energy system is used to evaluate the competitive position of natural gas fired combined cycle gas turbines (CCGTs) in the energy sector as a whole. Competing in the sector are large-scale electricity generation technologies such as refurbished existing coal fired stations and advanced forms of coal fired generation. The modelling incorporates new data on electricity supply technologies and options.

International Nuclear Information System (INIS)

The Planning Process of Brazilian Electric Sector Expansion, their normative aspects, instruments, main agents and the planning cycles are described. The methodology of expansion planning is shown, with the interactions of several study areas, electric power market and the used computer models. The forecasts of methodology evolution is also presented. (C.G.C.).

Energy Technology Data Exchange (ETDEWEB)

Smooth and notched specimens of the bearing steel 100Cr6 (SAE 52100) in a bainitic condition were used to determine the S-N-curves under tensile, torsional and combined in- and out-of-phase loading. In the area of high-cycle-fatigue, crack initiation was most likely caused by inclusions like Titanium Carbonitrides or Aluminium Oxides. A model was developed to describe the influence of the magnitude of these inclusions on the lifetime. A weakest link model, using the statistical distribution of inclusions and surface flaws, was used to describe the fatigue limit. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A catalytic converter of a ceramic monolith honeycomb substrate, coated with a washcoat of catalyst and attached to a natural gas/diesel dual fuel engine was simulated and studied experimentally. The paper describes the application of one-dimensional finite element model for the transient and steady state operation. Laminar flow was approximated using a dispersed plug flow model, and chemical kinetics were simulated using LHHW (Langmuir/ Hinshelwood/ Hougan/ Watson) type expressions. Simulation results were compared with experimental results for heating and cooling cycles which resulted from speed and load changes on the engine. The comparison showed a maximum difference between the two sets of emission levels of about 10 per cent, showing that the one-dimensional model is acceptable model for this dual fuel engine converter combination. 50 refs., 3 tabs., 13 figs.

International Nuclear Information System (INIS)

The Cycle 8A static tests conducted in the Fast Flux Test Facility (FFTF) during 1986 have resulted in the separation of various feedback reactivity components. These feedback components, described by closed-form equations depending only on the reactor temperature field, can be regarded as database for the validation and/or calibration of feedback mechanistic models. The SASSYS safety analysis code contains the most developed feedback reactivity models and was selected for the comparison study between database and mechanistic calculations for the FFTF. Although detailed feedback models for control rod repositioning and core radial expansion/bowing exist, only the simple models were available in SASSYS at the time of this study. The results are described in this paper.

Energy Technology Data Exchange (ETDEWEB)

This paper is an application of the economic model developed in Part 1 and programmed in the computer code PEACES (program for the economic analysis of combined energy systems). A case study is presented in which hypothetical energy requirements at an industrial site are considered and an exercise is conducted wherein cogeneration is considered as a means of improving the energy situation at the site. Appropriate technologies that can satisfy the cogeneration requirements are investigated and technical and economic evaluations are carried out for a feasibility assessment. Of the three proposals considered, the gas turbine with heat recovery steam generator and the gas/steam turbine combined cycle cogeneration plant were found to be economically viable, while the steam turbine was not. It was recommended that the gas/steam turbine combined cycle cogeneration proposal be adopted, as it was the most economical. (Author)

International Nuclear Information System (INIS)

A dynamic control rod worth measurement was performed for control bank D, C, B, and A of Yonggwang unit 1 cycle 14 during its low power physics test. MASTER was used for three-dimensional core kinetics calculations required to convert excore detector signal into static rod worth, using the same modeling and cross sections as ANC which was used for the core static design. A signal curve fitting method was proposed to solve a low signal problem due to large amount of rod worth, which leads to the distortion of resulting static worth. The static worths measured in this test well agreed with the predicted worth of design within #+-#15% which is a test requirement of rod worth measurement.

International Nuclear Information System (INIS)

The proposed method to analyze the composition of the cost of electricity is based on the energy conversion processes and the destruction of the exergy through the several thermodynamic processes that comprise a combined cycle power plant. The method uses thermoeconomics to evaluate and allocate the cost of exergy throughout the processes, considering costs related to inputs and investment in equipment. Although the concept may be applied to any combined cycle or cogeneration plant, this work develops only the mathematical modeling for three-pressure heat recovery steam generator (HRSG) configurations and total condensation of the produced steam. It is possible to study any nx1 plant configuration (n sets of gas turbine and HRSGs associated to one steam turbine generator and condenser) with the developed model, assuming that every train operates identically and in steady state. The presented ...

Energy Technology Data Exchange (ETDEWEB)

Combined energy plants operating on the Brayton-Rankine cycle have gained wide acceptance as the most efficient energy conversion system. The technology is well proven and numerous research activities are underway to develop it further past its present plateau of performance. In developed and emerging economies alike, the current situation in the global economic market has caused the liberalisation of the energy industry in some countries, and in others it is causing a rethink of economic and energy policies. A result is that electric utility companies that have enjoyed a monopoly in power generation and distribution are seeing this privilege being eroded. This is opening up opportunities for independent power production and, consequently, for gas/steam turbine plants because of the technical merits of the technology and its ability to fill the vacuum being created in the energy industry. An economic model has been developed for carrying out ...

International Nuclear Information System (INIS)

The aim of this study was to assess the influence of the normal menstrual cycle and of menopause on the gastric emptying rate of solids. Gastric emptying was studied in 15 premenopausal and ten postmenopausal women with an isotopic technique after the ingestion of a radiolabelled test meal. Premenopausal women were studied twice: Within 1 week prior to menses and again 1 week after onset of menses. Postmenopausal women were studied only once. The emptying curves of the solid component of the meal fitted a linear model. The half-emptying time was 78#+-#5 min during the follicular phase, 75#+-#7 min during the luteal phase and 76#+-#6 min in postmenopausal women (differences not statistically significant). The mean percentages of the meal retained in the stomach at different time intervals were also similar in the three groups. These results suggest that the menstrual cycle does not influence the gastric emptying rate of ...

International Nuclear Information System (INIS)

The accurate prediction of local hot spot during normal operation is important to ensure core thermal margin in a very high temperature gas-cooled reactor because of production of its high temperature output. The active cooling of the reactor core determining local hot spot is strongly affected by core bypass flows through the inter-column gaps between graphite blocks and the cross gaps between two stacked fuel blocks. The bypass gap sizes vary during core life cycle by the thermal expansion at the elevated temperature and the shrinkage/swelling by fast neutron irradiation. This study is to investigate the impacts of the variation of bypass gaps during core life cycle as well as core restraint mechanism on the amount of bypass flow and thus maximum fuel temperature. The core thermo fluid analysis is performed using the GAMMA+ code for the PMR200 block-core design. For the analysis not only are some modeling features, ...

Energy Technology Data Exchange (ETDEWEB)

A flowing bed kiln is a gas-solid reactor used in the civil nuclear fuel cycle for the successive conversion of uranium trioxide (UO{sub 3}) into uranium dioxide (UO{sub 2}) and then into uranium tetrafluoride (UF{sub 4}). A numerical model is developed which simulate the behaviour of this reactor in permanent regime. This model describes the physico-chemical phenomena involved, and combines a mechanistic approach in the vertical area of the kiln (resolution by the finite volumes method) and a systemic approach in the horizontal area, like in the model of cascade mixers. The first results have been obtained for reference operating conditions of the industrial kiln. Some possible improvements of the optimum temperature progression inside the kiln are evoked. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

A method of modeling freeze-thaw cycles of naturally deposited snowpacks is presented. The model involves the Stefan condition as an independent governing equation on the exterior moving boundary to calculate snowpack thinning, flow of water through a variably saturated layered porous medium as described by the Richards equation, and heat conduction with a phase change. The heat conduction problem was treated in two ways. Local heat conduction between a snow grain and its surrounding water film was treated by using a simple energy balance. Global heat conduction with a phase change (the Stefan problem) was introduced to calculate the space-time temperature distribution. In order to handle multiple interior moving boundaries, a specific form of the enthalpy formulation was used for heat conduction with a phase change. Changing material properties were considered according to the calculated meltwater refreezing. 48 refs., 11 ...

Energy Technology Data Exchange (ETDEWEB)

Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam- cycle is the conventional conversion method; however, total energy conversion efficiencies for this type of process are only slightly over 30{percent}. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40{percent}. Conversion processes based on gasification offer efficiencies above 50{percent}. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. Problems arise due to the corrosive nature of H{sub 2}S on metal components contained in these cycles. Because of this, H{sub 2}S concentrations must be reduced to low levels corresponding to certain power applications. An advanced process for the separation of hydrogen sulfide (H{sub 2}S) from coal ...

Energy Technology Data Exchange (ETDEWEB)

Nuclear fuel cycle activities of the former Soviet Union (FSU) have resulted in massive contamination of the environment in western Siberia. We are developing three-dimensional numerical models of the hydrogeology and potential contaminant migration in the West Siberian Basin. Our long-term goal at Pacific Northwest Laboratory is to help determine future environmental and human impacts given the releases that have occurred to date and the current waste management practices. In FY 1993, our objectives were to (1) refine and implement the hydrogeologic conceptual models of the regional hydrogeology of western Siberia developed in FY 1992 and develop the detailed, spatially registered digital geologic and hydrologic databases to test them, (2) calibrate the computer implementation of the conceptual models developed in FY 1992, and (3) develop general geologic and hydrologic information and preliminary ...

Environmental Research Database

ObjectivesWe have developed a life cycle perspective inspired conceptual model (CM) that suggests the importance of terrestrial ecosystems as a major repository of ZnO, TiO2, and Ag (Tier 1) manufactured nanomaterials (MNMs) introduced via the land application of MNM-containing biosolids. We propose to investigate the transport, fate, behavior, bioavailability, and effects of MNMs in(to) agroecosystems under environmentally realistic scenarios organized around three key hypotheses: Hypothesis (H1) Surface [continued...]DescriptionWe have developed a life cycle perspective inspired conceptual model (CM) that suggests the importance of terrestrial ecosystems as a major repository of ZnO, TiO2, and Ag (Tier 1) manufactured nanomaterials (MNMs) introduced via the land application of MNM-containing biosolids. We propose to investigate the transport, fate, behavior, bioavailability, and effects of MNMs in(to) ...

Energy Technology Data Exchange (ETDEWEB)

The research has involved the characterization of catalyst acidity, [sup 2]D NMR studies of Bronsted acid sites, and kinetic, calorimetric, and spectroscopic studies of methylamine synthesis and related reactions over acid catalysts. Approach of this work was to explore quantitative correlations between factors that control the generation, type, strength, and catalytic properties of acid sites on zeolite catalysts. Microcalorimetry, thermogravimetric analysis, IR spectroscopy, and NMR spectroscopy have provided information about the nature and strength of acid sites in zeolites. This was vital in understanding the catalytic cycles involved in methylamine synthesis and related reactions over zeolite catalysts.

Energy Technology Data Exchange (ETDEWEB)

The integration of a gas turbine into a new type of coal-fired combined cycle power plant necessitates a multiplicity of far-reaching changes compared with a normal design. The extremely high pre-heating temperature of the air emanating from the heat exchanger of the fluidized bed for the gas turbine combustion chamber has necessitated extensive development work and associated combustion trials. It was possible for these results to influence the design of the burners whereas the manufacture of other components which was on the critical path was already far advanced.

Energy Technology Data Exchange (ETDEWEB)

A new 500 kV one cycle electric circuit breaker with a mininum interrupting time of 12.5 m sec is described. The breaker, associated with a 1/4 cycle relay, insures a one cycle interruption. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

The development of rechargeable lithium batteries with a high mass capacity, made with non-toxic and low cost materials is an important industrial challenge. Morphological and structural modifications occurring in the electrode materials during charge-output cycles should not lower the electrochemical characteristics and the cycling properties of the battery. Thus the structure of electrode materials must be sufficiently deformable and stable to support the constraints linked with lithium intercalation and de-intercalation (ions and electrons absorption/extraction). The aim of this work is to explain some characteristics (mass capacity, ions and electrons mobility, cycling) using the relation between some mechanisms of lithium insertion (sites occupation, lattice reduction mods) and the nature of atoms and chemical bonds (covalence, ionicity). This approach is developed on 2-D models of crystallized and ...

Science.gov (United States)

The Process Waste Treatment Plant (PWTP) at the Oak Ridge National Laboratory is designed to remove radioactive contaminants, principally {sup 90}Sr, from process wastewater. Planned upgrades to the PWTP will use chabazite zeolite columns. Pilot-scale studies have shown that mass transfer zone lengths increase from 10 to about 30 cm as the superficial velocity increases from 5.5 to 22 cm/min. Calculations with a multicomponent equilibrium model showed that the distribution coefficient for strontium remains essentially constant over the process conditions, suggesting that a simple kinetic model (the Rosen long-bed solution) should adequately represent breakthrough behavior. Using a distribution coefficient of 4.87 L/g predicted by the equilibrium model, good agreement was found between experimental breakthrough curves and those calculated with the Rosen solution. This model allows prediction of bed ...

Energy Technology Data Exchange (ETDEWEB)

In recent years the 'Nowcasting Wake Vortex Impact Variables' model NOWVIV has been developed at the Deutsches Zentrum fuer Luft- und Raumfahrt, DLR, to forecast weather parameters in airport environments. The German Meteorological Service, DWD, employs his COSMO-DE model (COnsortium for Small scale Modelling-DEutschland) for operational forecasts in Germany. A systematic comparison of model output from NOWVIV and a derivate of COSMO-DE, named COSMO-FRA, is presented. Both models are centred at Frankfurt Airport with horizontal resolutions of 2.1 km and 2.8 km, respectively. In the DLR Project Wetter and Fliegen the COSMO-FRA model will replace the NOWVIV model and become a key component in the future rapid update cycle for adverse weather predictions at the airports of Frankfurt and Munich. The ...

CERN Document Server

The unavoidable irreversible losses of power in a heat engine are found to be of quantum origin. Following thermodynamic tradition a model quantum heat engine operating by the Otto cycle is analyzed. The working medium of the model is composed of an ensemble of harmonic oscillators. A link is established between the quantum observables and thermodynamical variables based on the concept of canonical invariance. These quantum variables are sufficient to determine the state of the system and with it all thermodynamical variables. Conditions for optimal work, power and entropy production show that maximum power is a compromise between the quasistatic limit of adiabatic following on the compression and expansion branches and a sudden limit of very short time allocation to these branches. At high temperatures and quasistatic operating conditions the efficiency at maximum power coincides with the endoreversible result. The optimal ...

Energy Technology Data Exchange (ETDEWEB)

A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat exergy efficiency is over 80%. (author)

British Library Electronic Table of Contents (United Kingdom)

This project is about the simulation design of an engine control unit (ECU) for an Otto cycle engine with electronic fuel injection (EFI). The simulation includes a model for the ECU as well as physical parameters of the engine, which allows closed-loop control and monitoring of various systems.This simulation has been realized using Simulink and Stateflow, which are components of Mathworks' MATLAB software.The program allows control of various parameters of the ECU, as well as the simulation of failures to verify that the designed ECU is fault-tolerant and can control the engine using an open loop control. The main function the ECU provides is fuel metering.Subsequently, this program could be used as a tool to quickly develop and test models of ECU in order to control an engine in laborat...

Energy Technology Data Exchange (ETDEWEB)

A compartment model, including removal of organic matter in a forest ecosystem, is developed to describe matter cycling and net CO{sub 2} flux of the ecosystem especially of managed forests. The model consists of five carbon stocks: atmosphere, foliage, woody matter, underground matter, and dead organic matter in the soil. Employing appropriate values of ecophysiological parameters in the model and simulation of man-made sugi (Cryptomeria japonica D. Don) plantation forests shows that these forests have high growth potential with a maximum total phytomass of over 750 t ha{sup -1} in dry matter basis. When the typical pattern of thinning regime for sugi plantation forests in Japan is applied to the present model, the simulated forest biomass developments compare well with mensuration data from various forestry sites. The CO{sub 2} balance between the sugi forest ecosystem and the ...

International Nuclear Information System (INIS)

This paper reports on steam injection cycle which is similar to supplementary fired combined cycle, but for the utilized steam medium produced by HRSG, its temperature is higher and pressure is lower than in the combined cycle. In comparison with the thermodynamic advantage of the two cycles, a clear understanding of physical concept can be gotten simply by energy balance. The difference of total power output between them is subtraction of enthalpy difference of exhaust steam and feed water of HRSG in steam injection cycle from the rejected heat by water coolant of condenser in combined cycle, when using the identical gas turbine and the same amount of total fuel consumption. In general case, formulas and data are given to indicate this comparison by the ratio of steam mass flow supplied by HRSG of the two cycles. The analysis of Cheng ...

Science.gov (United States)

The Department of Defense (DoD) has long depended on military support functions enabled by space reconnaissance, surveillance, and target acquisition (RSTA) assets. Future generation satellite capabilities will further push technologies in space - if the right technologies are deployed in the right numbers and with the right payloads. Modeling and simulation play major parts in developing and deploying such assets: 1) system and operational requirements determination, and 2) assessment of military utility of such assets. Each area is critical in a system"s life cycle. Requirements determination cuts across the issues of doctrine, organizations, training, materiel, leader development, personnel, and facilities (DOTMLPF). Military utility assessments are necessary to explore and quantify the military worth/benefit of space RSTA assets to operational commanders. Each of these areas requires relevant modeling/simulation tools ...

Energy Technology Data Exchange (ETDEWEB)

A new type of passive cooling system has been invented (Forsberg 1993): the Temperature-Initiated Passive Cooling System (TIPACS). The characteristics of the TIPACS potentially match requirements for an improved reactor-cavity-cooling system (RCCS) for the modular high-temperature gas-cooled reactor (MHTGR). This report is an initial evaluation of the TIPACS for the MHTGR with a Rankines (steam) power conversion cycle. Limited evaluations were made of applying the TIPACS to MHTGRs with reactor pressure vessel temperatures up to 450 C. These temperatures may occur in designs of Brayton cycle (gas turbine) and process heat MHTGRs. The report is structured as follows. Section 2 describes the containment cooling issues associated with the MHTGR and the requirements for such a cooling system. Section 3 describes TIPACS in nonmathematical terms. Section 4 describes TIPACS`s heat-removal capabilities. Section 5 analyzes the operation of the ...

Energy Technology Data Exchange (ETDEWEB)

Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with high temperature strength and good low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, IN 718 is the most widely used in the aerospace industry. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the ...

International Nuclear Information System (INIS)

Using standard microfabrication techniques, it is now possible to construct devices that appear to reliably manipulate electrons one at a time. These devices have potential use as building blocks in quantum computing devices, or as a standard of electrical current derived only from a frequency and the fundamental charge. To date, the error rate in semiconductor 'tuneable-barrier' pump devices, those which show most promise for high-frequency operation, have not been tested in detail. We present high-accuracy measurements of the current from an etched GaAs quantum dot pump, operated at zero source-drain bias voltage with a single ac-modulated gate at 340 MHz driving the pump cycle. By comparison with a reference current derived from primary standards, we show that the electron transfer accuracy is better than 15 parts per million. High-resolution studies of the dependence of the pump current on the quantum dot tuning parameters also reveal possible deviations from a ...

Science.gov (United States)

This paper builds upon previous work [Sprigg and Ehlen, 2004] by introducing a bond market into a model of production and employment. The previous paper described an economy in which households choose whether to enter the labor and product markets based on wages and prices. Firms experiment with prices and employment levels to maximize their profits. We developed agent-based simulations using Aspen, a powerful economic modeling tool developed at Sandia, to demonstrate that multiple-firm economies converge toward the competitive equilibria typified by lower prices and higher output and employment, but also suffer from market noise stemming from consumer churn. In this paper we introduce a bond market as a mechanism for household savings. We simulate an economy of continuous overlapping generations in which each household grows older in the course of the simulation and continually revises its target level of savings according to a ...

International Nuclear Information System (INIS)

A model has been developed in the recent past to predict fatigue crack growth (FCG) behaviour in the Paris-regime of various steels by employing low cycle fatigue (LCF) properties. The model forms its basis on the assumption that the cyclic damage process immediately ahead of a crack-tip, restricted in a small zone termed as process zone, is identical to those experienced in the LCF loading of a smooth specimen. Within the process zone, fatigue damage has been assumed in terms of product of stress and plastic strain which is analogous to the plastic strain energy density of the smooth specimen under fatigue loading. In this paper the model developed by Kujawski and Ellyin has been used to predict the FCG behaviour of an #alpha#-#beta# titanium alloy in the Paris-regime by employing the experimentally obtained LCF properties. The FCG behaviour thus theoretically predicted was compared with the ...

International Nuclear Information System (INIS)

This paper summarizes the progress to date by CH2M HILL and the UKAEA in development of a parametric modelling capability for estimating the costs of large nuclear decommissioning projects in the United Kingdom (UK) and Europe. The ability to successfully apply parametric cost estimating techniques will be a key factor to commercial success in the UK and European multi-billion dollar waste management, decommissioning and environmental restoration markets. The most useful parametric models will be those that incorporate individual components representing major elements of work: reactor decommissioning, fuel cycle facility decommissioning, waste management facility decommissioning and environmental restoration. Models must be sufficiently robust to estimate indirect costs and overheads, permit pricing analysis and adjustment, and accommodate the intricacies of international monetary exchange, currency ...

Energy Technology Data Exchange (ETDEWEB)

Cereal straw, a by-product in the production of agricultural crops, is considered as a potentially large source of energy supply with an estimated value of 47 x 10{sup 18} J worldwide. However, there is some debate regarding the actual amounts of straw which could be removed from arable soils without jeopardizing their quality, as well as the potential trade-offs in the overall straw-to-energy chain compared to the use of fossil energy sources. Here, we used a deterministic model of C and N dynamics in soil-crop systems to simulate the effect of straw removal under various sets of soil, climate and crop management conditions in northeastern France. Model results in terms of nitrate leaching, soil C variations, nitrous oxide and ammonia emissions were subsequently inputted into the life-cycle assessment (LCA) of a particular bio-energy chain in which straw was used to generate heat and power in a plant producing bio-ethanol ...

Energy Technology Data Exchange (ETDEWEB)

The theoretical analysis of a partially-ionized hydrogen gas flow (gas temperatures of approximately 10,000 to 20,000 K) through a particular class of magnetohydrodynamic (MHD) generators and the preliminary design of these MHD generators as open cycle, electric power supplies are performed. Analysis of the gas flow through these ultra-high temperature MHD generators requires a coupled gas dynamics/radiative heat transfer solution. Gas dynamics are modeled by a set of quasi-one-dimensional, nonlinear differential equations which account for friction, convective and radiative heat transfer and the interaction between the ionized gas and applied magnetic field. Radiative heat transfer is modeled using non-gray, absorbing-emitting two- and three-dimensional P-1 approximations which permit an arbitrary variation of the spectral absorption coefficient with frequency. Gas dynamics and radiative heat transfer are coupled through ...

International Nuclear Information System (INIS)

The purpose of this study was to compare a double freeze-thaw protocol to a triple freeze-thaw protocol for pulmonary cryoablation utilizing an in vivo porcine lung model. A total of 18 cryoablations were performed in normal porcine lung utilizing percutaneous technique with 9 each in a double- (10-5-10) and triple-freeze (3-3-7-7-5) protocol. Serial noncontrast CT images were obtained during the ablation. CT imaging findings and pathology were reviewed. No imaging changes were identified during the initial freeze cycle with either protocol. However, during the first thaw cycle, a region of ground glass opacity developed around the probe with both protocols. Because the initial freeze was shorter with the triple freeze-thaw protocol, the imaging findings were apparent sooner with this protocol (6 vs. 13 min). Also, despite a shorter total freeze time (15 vs. 20 min), the ablation zone identified with the triple freeze-thaw ...

International Nuclear Information System (INIS)

Numerous mercury intrusion porosimetry (MIP) studies have been carried out to investigate the pore structure in cement-based materials. However, the standard MIP often results in an underestimation of large pores and an overestimation of small pores because of its intrinsic limitation. In this paper, an innovative MIP method is developed in order to provide a more accurate estimation of pore size distribution. The new MIP measurements are conducted following a unique mercury intrusion procedure, in which the applied pressure is increased from the minimum to the maximum by repeating pressurization-depressurization cycles instead of a continuous pressurization followed by a continuous depressurization. Accordingly, this method is called pressurization-depressurization cycling MIP (PDC-MIP). By following the PDC-MIP testing sequence, the volumes of the throat pores and the corresponding ink-bottle pores can be determined at every pore size. These ...

UK PubMed Central (United Kingdom)

Metazoan life cycles can be complex in different ways. A number of diverse phenotypes and reproductive events can sequentially occur along the cycle, and at certain stages a variety of developmental...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

SummaryBackground Intracellular transport via processive kinesin, dynein, and myosin molecular motors plays an important role in maintaining cell structure and function. In many cases, cargoes move distances longer than expected for single motors; there is significant evidence that this increased travel is in part due to multiple motors working together to move the cargoes. Although we understand single motors experimentally and theoretically, our understanding of multiple motors working together is less developed. Results We theoretically investigate how multiple kinesin motors function. Our model includes stochastic fluctuations of each motor as it proceeds through its enzymatic cycle. Motors dynamically influence each other and function in the presence of thermal noise and viscosity. We...

British Library Electronic Table of Contents (United Kingdom)

Abstract A large remaining source of uncertainty in global model predictions of future climate is how ecosystem carbon (C) cycle feedbacks to climate change. We conducted a field manipulative experiment of warming and nitrogen (N) addition in a temperate steppe in northern China during two contrasting hydrological growing seasons in 2006 [wet with total precipitation 11.2% above the long-term mean (348 mm)] and 2007 (dry with total precipitation 46.7% below the long-term mean). Irrespective of strong intra- and interannual variations in ecosystem C fluxes, responses of ecosystem C fluxes to warming and N addition did not change between the two growing seasons, suggesting independence of warming and N responses of net ecosystem C exchange (NEE) upon hydrological variations in the temperate ...

International Nuclear Information System (INIS)

During their catalytic cycle, proteins involved in biological signal transduction undergo unexpectedly large conformational changes, which are at the core of their biological functioning. Until now it has been extremely difficult to obtain experimental insight into the nature of these conformational changes. Mathematical modeling and time-resolved X-ray crystallography have resulted in probable routes along which these conformational changes may take place, but so far this fundamental biological phenomenon has hardly been tackled experimentally. Here, we report on an attempt to observe structural changes in Photoactive Yellow Protein with time-resolved small-angle neutron scattering using diffractometer D22 at the high-flux reactor of the Institut Laue-Langevin, Grenoble, France

British Library Electronic Table of Contents (United Kingdom)

In today's maturing consumer markets, emphasis is shifting from straightforward sales to a more holistic approach to customer life cycle management, with a stronger emphasis on how sales are generated and service provided all along the customer journey. Effectively managing these different marketing, sales and service channels poses a significant challenge. Companies need new strategies, structures, processes and tools to deliver customer value across all channels. A multi-channel, integrative customer model that delivers customer value and significant return on investment (ROI) requires both a strong understanding of customer preferences and behaviours and a robust IT architecture that supports the overarching customer relationship management (CRM) strategy. Even those organizations that ...

British Library Electronic Table of Contents (United Kingdom)

Maintenance of genomic integrity in embryonic cells is pivotal to proper embryogenesis, organogenesis and to the continuity of species. Cultured mouse embryonic stem cells (mESCs), a model for early embryonic cells, differ from cultured somatic cells in their capacity to remodel chromatin, in their repertoire of DNA repair enzymes, and in the regulation of cell cycle checkpoints. Using 129XC3HF1 mESCs heterozygous for Aprt, we characterized loss of Aprt heterozygosity after exposure to ionizing radiation. We report here that the frequency of loss of heterozygosity mutants in mESCs can be induced several hundred-fold by exposure to 5-10Gy of X-rays. This induction is 50-100-fold higher than the induction reported for mouse adult or embryonic fibroblasts. The primary mechanism underlying the...

Energy Technology Data Exchange (ETDEWEB)

SPEOS takes advantage of a geological situation which apparently does not occur much in Switzerland. The SPEOS pilot installation, which was erected in 1982, is designed for the supply of heat for about 500 persons. In the course of 10 cycles, the possibilities and limits of the seasonal heat storage were displayed. It was demonstrated that large quantities of heat with temperatures of up to 75 C can be stored in an aquifer. The behaviour of such a storage can be predicted with sufficient accuracy with mathematical models. (author) 12 refs.

International Nuclear Information System (INIS)

Electrical penetration assemblies mounted on the containment wall are used to carry electrical power and signals from the equipment inside this containment (e.g. recirculation pumps, control rod position indications etc.) Todays BWR nuclear power plants apply epoxy resin sealed electric penetration. Contrariwise, the epoxy resin (organic sealant) was replaced with sodium barium glass (inorganic) by way of trial in search for a quality sealant. The glass sealant has been proved to have high temperature airtightness at 300 degC above from an evaluation test involving full-scale model parts. Environmental tests were conducted continuously as to heat cycle, vibration and LOCA etc. the specimens (module) of five types. They were made certain of conformity to the design requirements for boiling water operation. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper develops optimal bidding strategies for a pumped-storage plant in a pool-based electricity market. In the competitive regime, when compared to simple hydroelectric generator, profit of the pumped-storage plant is maximized by operating it as a generator when market clearing price is high and as a pump when the price is low. Based on forecasted hourly market clearing price, a multistage looping algorithm to maximize the profit of a pumped-storage plant is developed, considering both the spinning and non-spinning reserve bids and meeting the technical operating constraints of the plant. The proposed model is adaptive for the nonlinear three-dimensional relationship between the power produced, the energy stored, and the head of the associated reservoir. Different operating cycles for a realistic pumped-storage plant are considered and simulation results are reported and compared. (author)

CERN Document Server

Tolerancing of assembly mechanisms is a major interest in the product life cycle. One can distinguish several models with growing complexity, from 1-dimensional (1D) to 3-dimensional (3D) (including form deviations), and two main tolerancing assumptions, the worst case and the statistical hypothesis. This paper presents an approach to 3D statistical tolerancing using a new acceptance criterion. Our approach is based on the 1D inertial acceptance criterion that is extended to 3D and form acceptance. The modal characterisation is used to describe the form deviation of a geometry as the combination of elementary deviations (location, orientation and form). The proposed 3D statistical tolerancing is applied on a simple mechanism with lever arm. It is also compared to the traditional worst-case tolerancing using a tolerance zone.

Energy Technology Data Exchange (ETDEWEB)

A hollow-fiber crossflow microfiltration membrane was utilized to retain a biomass of Pseudomonas aeruginosa PU21 for continuous biosorption of lead (Pb), copper (Cu), and cadmium (Cd) ions in single or ternary metal systems. The results obtained from the microfiltration systems showed that in both single and ternary biosorption, the metal removal efficiency based on a molar basis was clearly Pb > Cu > Cd. For a single-membrane process with an influent metal concentration of 200 {micro}M and a flow rate of 350 mL/h, the effluent concentration of Pb and Cu satisfied the national regulations for an influent volume of 6.3 L. With a three-metal influent, the adsorption capacity of the biomass for Pb, Cu, and Cd was reduced 4, 50, and 74% compared to that for single-metal adsorption. Selective biosorption with a three-column sequential microfiltration operation exhibited an enhancement of 40 and 57% of total metal removal for Cu and Cd, respectively, over the results from ...

Energy Technology Data Exchange (ETDEWEB)

The Asia-Pacific region will see tremendous growth in demand for electricity in the next few decades and will be an important market for generation equipment and associated services. The Association of Southeast Asian Nations (ASEAN) countries alone anticipate additional power demand of more than 37,000 NM by the year 2000, with an estimated total expenditure of US $85 billion. Trends in recent years show natural gas-fired combined cycle in plants to be fast gaining in popularity over conventional thermal plants. The advantages include increased primary energy conversion efficiency coupled with significant reduction in pollutant emissions, shorter construction times, faster loading rates and reduced staffing requirements. In the computer model used for generation capacity expansion planning in Tenaga Nasional Berhad, clean coal technology models are not used as candidate plants. In the opinion of the authors, this results ...

Science.gov (United States)

We consider a unified model of Fe ion acceleration in the solar corona. The model comprises charge-changing processes, Coulomb energy losses, and both regular and stochastic acceleration. At a given acceleration scenario, the type of acceleration is found to have a minor effect on the mean charge states, but the shapes of the charge-state distributions produced by regular acceleration and by stochastic acceleration are different. During a continual acceleration at coronal temperatures, iron ions typically follow rising trajectories on the charge-energy plane. These trajectories are situated below the mean equilibrium charge curve defined from the balance of ionization and recombination at fixed energy. During stopping, the iron ions cross the equilibrium charge curve and run through a series of charge states above the mean equilibrium charge at current energy, because the Coulomb deceleration rate significantly exceeds the rate of the ion ...

CERN Document Server

We solve the loop equations of the $\\beta$-ensemble model analogously to the solution found for the Hermitian matrices $\\beta=1$. For \\beta=1$, the solution was expressed using the algebraic spectral curve of equation $y^2=U(x)$. For arbitrary $\\beta$, the spectral curve converts into a Schr\\"odinger equation $((\\hbar\\partial)^2-U(x))\\psi(x)=0$ with $\\hbar\\propto (\\sqrt\\beta-1/\\sqrt\\beta)/N$. This paper is similar to the sister paper~I, in particular, all the main ingredients specific for the algebraic solution of the problem remain the same, but here we present the second approach to finding a solution of loop equations using sectorwise definition of resolvents. Being technically more involved, it allows defining consistently the B-cycle structure of the obtained quantum algebraic curve (a D-module of the form $y^2-U(x)$, where $[y,x]=\\hbar$) and to construct explicitly the correlation functions and the corresponding symplectic ...

Science.gov (United States)

This dissertation reports on the application of numerical optimization techniques as applied to fuel cell simulation and design. Due to the "multi-physics" inherent in a fuel cell, which results in a highly coupled and non-linear behavior, an experimental program to analyze and improve the performance of fuel cells is extremely difficult. This program applies new optimization techniques with computational methods from the field of aerospace engineering to the fuel cell design problem. After an overview of fuel cell history, importance, and classification, a mathematical model of solid oxide fuel cells (SOFC) is presented. The governing equations are discretized and solved with computational fluid dynamics (CFD) techniques including unstructured meshes, non-linear solution methods, numerical derivatives with complex variables, and sensitivity analysis with adjoint methods. Following the validation of the fuel cell model in 2-D and 3-D, the ...

Energy Technology Data Exchange (ETDEWEB)

A highly efficient integrated energy conversion system is built based on a methane catalytic decomposition reactor (MCDR) together with a direct carbon fuel cell (DCFC) and an internal reforming solid oxide fuel cell (IRSOFC). In the MCDR, methane is decomposed to pure carbon and hydrogen. Carbon is used as the fuel of DCFC to generate power and produce pure carbon dioxide. The hydrogen and unconverted methane are used as the fuel in the IRSOFC. A gas turbine cycle is also used to produce more power output from the thermal energy generated in the IRSOFC. The output performance and efficiency of both the DCFC and IRSOFC are investigated and compared by development of exact models of them. It is found that this system has a unique loading flexibility due to the good high-loading property of DCFC and the good low loading property of IRSOFC. The effects of temperature, pressure, current densities, and methane conversion on the performance of the ...

International Nuclear Information System (INIS)

In this paper a computational analysis of 11 fuel samples (seven UO_2 and four MOX) with a burn-up ranging from 20 MWd/kgHM up to 121 MWd/kgHM (HM: Heavy Metal) is carried out with the depletion module of the lattice code CASMO-4E [Rhod01, Rhod01b] using the neutron data libraries ENDF/B-VI and JEF-2.2 and a pin cell model. In order to assess the accuracy of the model and the depletion calculation in the determination of the isotopic inventory after several irradiation cycles, the calculated results were compared to experimental data gathered from a chemical isotopic analysis of the fuel samples performed at the Hot Laboratory at the Paul Scherrer Institut (PSI), Switzerland. Selected results of this comparison, which includes 54 isotopes (17 actinides and 37 fission products), are presented here. (orig.)

International Nuclear Information System (INIS)

Uranium Hexafluoride is a material used in the various processes which comprise the front end of the nuclear fuel cycle (conversion, enrichment and fuel fabrication). Confinement of UF6 is a very important safety requirement since this material is highly reactive and presents safety hazards to humans. The present paper discusses the safety relevant aspects of accidental releases of UF6 inside process confinement buildings. Postulated accidental scenarios are analyzed and their consequences evaluated. Implant releases rates are estimated using computer code predictions. A time dependent homogeneous compartment model is used to predict concentrations of UF6, hydrogen fluoride and uranyl fluoride inside a confinement building, as well as to evaluate source terms released to the atmosphere. These source terms can be used as input to atmospheric dispersion models to evaluate consequences to the environment. The results can also ...

Energy Technology Data Exchange (ETDEWEB)

The use of global three-dimensional (3-D) models with satellite observations of CO2 in inverse modeling studies is an area of growing importance for understanding Earth s carbon cycle. Here we use the GEOS-Chem model (version 8-02-01) CO2 mode with multiple modifications in order to assess their impact on CO2 forward simulations. Modifications include CO2 surface emissions from shipping (0.19 PgC yr 1), 3-D spatially-distributed emissions from aviation (0.16 PgC yr 1), and 3-D chemical production of CO2 (1.05 PgC yr 1). Although CO2 chemical production from the oxidation of CO, CH4 and other carbon gases is recognized as an important contribution to global CO2, it is typically accounted for by conversion from its precursors at the surface rather than in the free troposphere. We base our model 3-D spatial distribution of CO2 chemical production on monthly-averaged loss rates of CO (a ...

International Nuclear Information System (INIS)

The safety analysis checklist scope and the criteria of key parameters needed to be checked for Daya bay reload cycles are introduced. The INCORE code package was used for the safety evaluation of Daya bay unit 2 cycle 2. The method and the contents can not only be applicable for Daya Bay reload cycles but also for Qinshan 600 MW and Qinshan 300 MW reload cycles.

International Science & Technology Center (ISTC)

Investigation of Destruction Mechanisms in Reactor Steels and Alloys under Cycling Deformation

International Nuclear Information System (INIS)

... FUEL CYCLE AND FUEL MATERIALS MATERIALS SCIENCE chromium-nickel

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper presents an investigation into the feasibility and potential advantages of a small scale Miller cycle natural gas engine for applications such as domestic combined heat and power systems. The Miller cycle engine is compared to a standard Otto cycle engine using cycle analyses and multidimensional simulation, and basic engine design implications are discussed. It is found that the Miller cycle engine has a potential for improved fuel efficiency, but at the cost of a reduced power to weight ratio. A fuel efficiency advantage of 5{yields}10% compared to a standard Otto cycle engine appears possible, however it is stated that further investigations, in particular into the topic of engine friction, are required in order to validate the findings. (author)

Energy Technology Data Exchange (ETDEWEB)

Deteriorating air quality in urban areas is leading bus manufacturers to look for cleaner drives of urban buses. Various new systems are now available, but it is difficult to compare them and verify their effects without having a driving cycle accurately representing contemporary average urban bus use. The idealized form (engine cycle, passenger car cycle or different kW/tonnes ratio and traffic conditions) of existing driving cycles disqualifies them for the purpose. For this reason, it was decided to attempt the development of a new driving cycle for urban buses. To this end, measurements were carried out on buses in service in four major Dutch towns. The resulting data were combined to produce a reference cycle comprising all data relating to urban bus use. Statistical methods were then used to compare a large number of 15-20 minute ...

Energy Technology Data Exchange (ETDEWEB)

In this report is described the work effort performed to provide NETL with VE-Suite based Virtual Engineering software and enhanced equipment models to support NETL's Advanced Process Engineering Co-simulation (APECS) framework for advanced power generation systems. Enhancements to the software framework facilitated an important link between APECS and the virtual engineering capabilities provided by VE-Suite (e.g., equipment and process visualization, information assimilation). Model enhancements focused on improving predictions for the performance of entrained flow coal gasifiers and important auxiliary equipment (e.g., Air Separation Units) used in coal gasification systems. In addition, a Reduced Order Model generation tool and software to provide a coupling between APECS/AspenPlus and the GE GateCycle simulation system were developed. CAPE-Open model interfaces were ...

Energy Technology Data Exchange (ETDEWEB)

Kawasaki Heavy Industries, Ltd. has developed a gas turbine combined cycle and cogeneration plant computer aided engineering (CAE) system, which creates cycle heat balance automatically on given configurations of gas turbines, heat recovery boilers, steam turbines and auxiliaries. The system can predict the performance of the plant as a function of control set points, loads, process steam requirements and ambient conditions, which enables accurate and fast design of gas turbine combined cycle and cogeneration plants. (author)

Energy Technology Data Exchange (ETDEWEB)

The maintenance of a balance between cell gain and cell loss is essential for proper liver function. The exact role of aryl hydrocarbon receptor (AhR) in regulating cell proliferation and apoptosis of liver cells remains unclear, since ligand-dependent activation of AhR has been shown to induce cell cycle arrest, proliferation, differentiation or apoptosis, depending on the cellular model used. AhR can directly interact with retinoblastoma protein in hepatic cells, forming protein complexes that can efficiently block cell cycle progression by inducing G1 arrest, or to induce the expression of inhibitors of cyclin-dependent kinases, such as p271. On the other hand, it has been suggested that AhR could play a stimulatory role in cell proliferation, either directly or by mediating a release from contact inhibition. It is now generally accepted that progenitor cells exist in the liver, are activated in various liver diseases ...

Energy Technology Data Exchange (ETDEWEB)

A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency ...

Energy Technology Data Exchange (ETDEWEB)

This report presents the methodology and the results from the modelling of an open repository for spent nuclear fuel in Laxemar. Specifically, the present work analyses the hydrological effects of the planned repository during the construction and operational phases when it is open, i.e. air-filled, and hence may cause a disturbance of the hydrological conditions in the surroundings. The numerical modelling is based on the SDM-Site Laxemar MIKE SHE model. The modelling was divided into three steps. The first step was to update the SDM-Site Laxemar model with a new hydrogeological bedrock model. The other main updates were an increase of the depth of the MIKE SHE model domain, enhanced vertical computational resolution and that the drainage of the Aespoe Hard Rock Laboratory was included in the model. The resulting ...

Energy Technology Data Exchange (ETDEWEB)

Smooth and notched specimens of the bearing steel 100Cr6 (SAE 52100) in a bainitic condition were used to determine the S-N curves under tensile, torsional and combined in- and out-of-phase loading. In the area of high-cycle fatigue, crack initiation was most likely caused by inclusions like Titanium Carbonnitrides or Aluminium Oxides. A micro mechanical model for the crack initiation by inclusions was developed. Another model was developed to describe the influence of these inclusions on the lifetime. A weakest-link model, using the statistical distribution of inclusions and surface flaws, was used to describe the endurance limit. (orig.) [German] Es wurden Woehlerlinien unter Zug-Druck-, Torsions- sowie kombinierter phasengleicher und phasenverschobener Zug-Druck- und Torsionsbelastung fuer glatte und gekerbte Proben des Stahls 100Cr6 (SAE 52100) im bainitischen Zustand erstellt. Im Bereich der ...

International Nuclear Information System (INIS)

One of the limiting contributors to the heat load constraint for a long term spent fuel repository is the decay of americium-241. A possible option to reduce the heat load produced by Am-241 is to eliminate it via transmutation in a light water reactor thermal neutron environment, in particular, by taking advantage of the large thermal fission cross section of Am-242 and Am-242m. In this study we employ lattice loading optimization techniques to define the loadings and arrangements of fuel pins with blended americium and uranium oxide in boiling water reactor bundles, specifically, by defining the incineration of pre-loaded americium as an objective function to maximize americium transmutation. Subsequently, the viability of these optimized lattices is tested by assembling them into bundles with Am-spiked fuel pins and by loading these bundles into realistic three-dimensional BWR core-wide simulations that model multiple reload cycles and ...

Science.gov (United States)

The objective of this paper is to reveal to what degree bio-based jet fuels (bio-jet) can reduce greenhouse gas (GHG) emissions from the US aviation sector. A model of the supply and demand chain of bio-jet involving farmers, bio-refineries, airlines, and policymakers is developed by considering factors that drive the decisions of actors (i.e. decision-makers and stakeholders) in the life cycle stages. Two kinds of feedstock are considered: oil-producing feedstock (i.e. camelina and algae) and lignocellulosic biomass (i.e. corn stover, switchgrass, and short rotation woody crops). By factoring in farmer/ feedstock producer and bio-refinery profitability requirements, land availability and suitability, as well as a time delay factor, a more realistic estimate of the level of bio-jet supply and emissions reduction can be developed under different oil price assumptions. Factors that drive bio-jet GHG emissions and unit production costs from each ...

International Nuclear Information System (INIS)

Regional arterial CO2 tension (PaCO2) reactivity of cerebral blood flow (CBF) and the effect of PaCO2 on the spatial and temporal heterogeneity of CBF were investigated by using autoradiographically determined CBF in the rat middle cerebral artery occlusion model after a 2-h period under pentobarbital anesthesia to clarify the relation between PaCO2 reactivity, CBF heterogeneity, and the temporal cycling of CBF. PaCO2 was adjusted to one of four levels. CBF was determined in four cortical areas and white matter using the tissue fractionation of [14C]iodoantipyrine [( 14C]IAP) in combination with vessel mapping using in vivo 4% thioflavine S. Specific PaCO2 reactivity and CBF were normal in the nonischemic cortex, normal, although slightly depressed, in the border zone far from the ischemic core area, and depressed in the border zone adjacent to the ischemic core area (P less than 0.001) and the ischemic core (P less than 0.001). In normocapnic ...

British Library Electronic Table of Contents (United Kingdom)

An Otto cycle engine with internal and external irreversibilities of friction and heat leakage, in which the heat transfer between the working fluid and the environment obeys linear phenomenological heat transfer law [q ?? ?(T ?1)], is studied in this paper. The optimal piston motion trajectory for maximizing the work output per cycle is derived for the fixed total cycle time and fuel consumed per cycle. Optimal control theory is applied to determine the optimal piston trajectories for the cases of with and without piston acceleration constraint on each stroke and the optimal distribution of the total cycle time among the strokes. The optimal piston motion with acceleration constraint for each stroke consists of three segments, including initial maximum acceleration and final maximum decel...

Energy Technology Data Exchange (ETDEWEB)

The advantage of high-resolution sequence stratigraphy, which takes base-levels as reference, is that it can be applied to continental depositional basins controlled by multiple factors and can effectively improve the accuracy and resolution of sequential stratigraphic analysis. Moreover, the principles of base-level cycles are also suitable for analyzing sequential stratigraphy in continental coal-bearing basins because of their accuracy in forecasting distribution of coal measures. By taking the Dongsheng coalfield in the Ordos basin as an example, the extensive application of base-level cycles in exploration and exploitation of coal is analyzed. The result shows that the Yan'an formation in the Dongsheng area is a long-term base-level cycle which is bordered by nonconformities and made up of five mid-term cycles and 13 short-term cycles. The long-term ...

Energy Technology Data Exchange (ETDEWEB)

A class-V myosin, myosin V, one of 18 known classes of actin-based motor proteins, plays a role in transporting organelles within a cell. Unlike myosin-II, which functions as an assembly in the thick filaments of muscle, myosin V is a two-headed processive motor protein, which functions as a single molecule: myosin V performs many consecutive steps before it detaches from an actin filament accompanied by catalytic cycles of ATP (adenosine 5'-triphosphate) ase. The mechanism of such chemomechanical steps is explained by a 'Hand-over-hand model' in which two heads of myosin V alternately repeat single-headed and double-headed bindings with an actin filament. To investigate the binding state of myosin V at several key nucleotide states during ATP hydrolysis, we measured the mechanical properties of a single myosin V - actin complex by applying an external load with optical trap.

Energy Technology Data Exchange (ETDEWEB)

The masses of the proton-rich nuclides {sup 85,86,87}Mo and {sup 87}Tc have been measured with the Penning trap mass spectrometer SHIPTRAP at GSI. The measured mass excesses of these nuclei deviate from the values of the Atomic Mass Evaluation 2003 by up to 1.6 MeV, indicating a systematic shift of the mass surface in this region compared to previous measurements. A local mass extrapolation based on the new results has been made for the mass range A=80-95. Measured and extrapolated mass values and the derived separation energies have been compared to theoretical mass models. Taking into account the new mass excess values, rp-process network calculations have been performed. Preliminary results show changes in the final abundances for A=86-92 by up to a factor of 30. Results of measurements and calculations are presented, and the issue of a potential Zr-Nb cycle is addressed.

Energy Technology Data Exchange (ETDEWEB)

The performance and lifetime of energy storage in batteries are an important part of many renewable based energy systems. Not only do batteries impact on the system performance but they are also a significant expenditure when considering the whole life cycle costs. Poor prediction of lifetime can, therefore, lead to uncertainty in the viability of the system in the long term. This report details the work undertaken to investigate and develop two different battery life prediction methodologies with specific reference to their use in hybrid renewable energy systems. Alongside this, results from battery tests designed to exercise batteries in similar modes to those that they experience in hybrid systems have also been analysed. These have yielded battery specific parameters for use in the prediction software and the first results in the validation process of the software are also given. This work has been part of the European Union Benchmarking research project ...

Energy Technology Data Exchange (ETDEWEB)

This paper examines the global impacts of a policy that internalizes the external costs (related to air pollution damage, excluding climate costs) of electricity generation using a combined energy systems and macroeconomic model. Starting point are estimates of the monetary damage costs for SO{sub 2}, NOX, and PM per kWh electricity generated, taking into account the fuel type, sulfur content, removal technology, generation efficiency, and population density. Internalizing these externalities implies that clean and advanced technologies increase their share in global electricity production. Particularly, advanced coal power plants, natural gas combined cycles, natural gas fuel cells, wind and biomass technologies gain significant market shares at the expense of traditional coal- and gas-fired plants. Global carbon dioxide emissions are lowered by 3% to 5%. Sulfur dioxide emissions drop significantly below the already low level. The policy ...

Energy Technology Data Exchange (ETDEWEB)

The impacts of the expected climate change on Finnish lake ecosystems were studied with the biota of the mesohumic Lake Paeaejaervi, southern Finland. Experimental conditions, from small-scale experiments on single species level to a large-scale ecosystem manipulation, were established to simulate directly the future climate and/or loading of nutrients and dissolved organic matter (DOM) from the drainage area. The experimental studies were accomplished by modelling the carbon flow in the pelagic food web as well as the growth of littoral macrophytes. The main hypothese tested were as follows: As a consequence of the climate change (rising temperature and increasing precipitation) the loading of nutrients and dissolved organic matter (DOM) from the drainage area to the lake will increase. In the pelagic zone this will be first reflected i higher productivity of primary producers and bacteria, but will later affect the entire food chain. Increase in atmospheric ...

Energy Technology Data Exchange (ETDEWEB)

The Cryocycling of Energetic Materials Project is sponsored by the Memorandum of Understanding (MOU) on advanced munition technologies. This MOU is an agreement between the Department of Energy and the Department of Defense (Office of Munitions) that facilitates the development of technologies of mutual interest to the two Departments. The cryocycling project is one of several that focus on demilitarization aspects of conventional weapons and weapon systems. During FY94 the project pursued the development of analytical and numerical models that can be used to describe and optimize the cryocycling process for preparing energetic materials for recycle and reuse. In addition, the demilitarization stockpile of the Department of Defense was analyzed to identify candidate munitions for the process, and pilot scale cryocycling operations were begun at an industrial contractor. When a material is cryocycled, it is repeatedly subjected to cycles of ...

Energy Technology Data Exchange (ETDEWEB)

A single particle micro-electrode technique has been applied, to study adsorption and mass transport phenomena of a TEABF{sub 4}/acetonitrile solution in a nano-porous carbon. The nano-porous carbon, which is obtained from SiC, has a very small and narrow pore size distribution around 8 Angstrom. Therefore, it is a good model material for studying adsorption processes in micropores. The results from cyclic voltammetry showed that a higher specific capacitance was obtained in the positive potential interval (vs Ag/AgNO{sub 3}). Upon activation cycling the mass transport inside the nano-porous particle becomes drastically hindered, probably by TEA{sup +} that is adsorbed and is partially blocking the micropores. Effective diffusion coefficients, Deff, were determined from potential step experiments. At positive potentials Deff was 1.5 {+-} 0.5 x 10{sup -8} cm{sup 2}s{sup -1}, whereas at more negative potentials Deff decreased drastically. ...

International Nuclear Information System (INIS)

The aim of the work in this thesis is to investigate the convective and diffusive transport in the TM chemistry transport model, and to investigate some aspects of the consequences for NOx. The large inaccuracy and uncertainty in the description of processes like convection and turbulent diffusion, the strong dependence of the radiative forcing of ozone on its vertical distribution, and the strong dependence of the ozone production on the distribution of NOx, are the main motivation. The availability of the ERA-40 data, where convective data and vertical diffusion coefficients are archived, allows a study of the effect of different convective mass flux sets, and different vertical diffusion coefficients on the model-simulated distribution of tracers. In this thesis the following questions are addressed : (1) How large is the sensitivity of the (model simulated) distribution of ozone and nitrogen oxides on (the) convection ...

UK PubMed Central (United Kingdom)

We show here sodium ion cycling between complex I from Klebsiella pneumoniae and the F₁F₀ ATP synthase from Ilyobacter tartaricus in a reconstituted...Full Text Available

International Nuclear Information System (INIS)

This paper presents part-load evaluation of a natural gas-fired chemical looping combustion (CLC) combined cycle with CO2 capture. The novel combined cycle employs an air-based gas turbine, a CO2-turbine and a steam turbine cycle. In this combined cycle, the CLC reactors replace combustion chamber of the gas turbine. The proposed combined cycle has a net plant efficiency of about 52.2% at full-load, including CO2 compression to 200 bar. The part-load evaluation shows that reducing the load down to 60% results in an efficiency drop of 2.6%-points. However, the plant shows better relative part-load efficiency compared to conventional combined cycles. The pressure in CLC-reduction and -oxidation reactors is balanced by airflow control, using a compressor equipped with variable guide vanes. A combination of control strategies is discussed for plant start-up and ...

Energy Technology Data Exchange (ETDEWEB)

Microstructural evolution due to thermal effects was studied in micro solder joints (55 {+-} 5 {micro}m). The composition of the Sn/Pb solder studied was found to be hypereutectic with a tin content of 65--70 wt%.This was determined by Energy Dispersive X-ray analysis and confirmed with quantitative stereology. The quantitative stereological value of the surface-to-volume ratio was used to characterize and compare the coarsening during thermal cycling from 0--160 C to the coarsening during annealing at 160 C. The initial coarsening of the annealed samples was more rapid than the cycled samples, but tapered off as time to the one-half as expected. Because the substrates to which the solder was bonded have different thermal expansion coefficients, the cycled samples experienced a mechanical strain with thermal cycling. The low-strain cycled samples had a 2.8% strain imposed on the ...

International Nuclear Information System (INIS)

The major driver to enhance the efficiency of the simple gas turbine cycle has been the increase in process conditions through advancements in materials and cooling methods. Thermodynamic cycle developments or cycle integration are among the possible ways to further enhance performance. The current paper presents the possibilities and advantages from the LOTHECO natural gas-fired combined cycle concept. In the LOTHECO cycle, low-temperature waste heat or solar heat is used for the evaporation of injected water droplets in the compressed air entering the gas turbine's combustion chamber. Following a description of this innovative cycle, its advantages are demonstrated by comparison between different gas turbine power generation systems for small and large-scale applications, including thermodynamic and economic analysis. A commercial gas turbine (ALSTOM GT10C) ...

UK PubMed Central (United Kingdom)

SummaryFor mammalian somatic cells the importance of microtubule cytoskeleton integrity in interphase cell cycle progression is uncertain. The loss, diminishment, or stabilization...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this paper we have proposed a novel gas turbine cycle with hydrogen-fueled chemical-looping combustion, and the system study on two hydrogen-fueled power plants, the new gas turbine cycle and an advanced gas turbine cycle with H{sub 2}/O{sub 2} combustion, has been investigated with the aid of exergy principle (EUD methodology). The hydrogen fueled chemical-looping combustion in the new gas turbine cycle consists of two successive reactions: hydrogen fuel is reacted with metal oxide (reduction of metal oxide), and then instead of air or pure oxygen, the reduced metal is successively oxidized by the saturated air. As a result, the new hydrogen-fueled gas turbine cycle has a breakthrough performance, with at least about 12 percentage-point higher efficiency compared to the gas turbine cycle with H{sub 2}/O{sub 2} combustion, and will be environmentally superior ...

Energy Technology Data Exchange (ETDEWEB)

X-ray crystal structures of L-3,4-dihydroxy-2-butanone-4-phosphate synthase from Magnaporthe grisea are reported for the E-SO{sub 4}{sup 2-}, E-{sub 4}{sup 2-}-Mg{sup 2+}, E-SO{sub 4}{sup 2-}-Mn{sup 2+}, E-SO{sub 4}{sup 2-}-Mn{sup 2+}-glycerol, and E-SO{sub 4}{sup 2-}-Zn{sup 2+} complexes with resolutions that extend to 1.55, 0.98, 1.60, 1.16, and 1.00 {angstrom}, respectively. Active-site residues of the homodimer are fully defined. The structures were used to model the substrate ribulose 5-phosphate in the active site with the phosphate group anchored at the sulfate site and the placement of the ribulose group guided by the glycerol site. The model includes two Mg{sup 2+} cations that bind to the oxygen substituents of the C2, C3, C4, and phosphate groups of the substrate, the side chains of Glu37 and His153, and water molecules. The position of the metal cofactors and the substrate's phosphate group are further stabilized by an ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Sunflower combined shaft unit Rankine cycle turboalternator

International Nuclear Information System (INIS)

... fast reactors fbr type reactors fuels liquid metal cooled reactors materials nuclear

Science.gov (United States)

This paper examines the relationships between the socio-demographic characteristics of small

International Nuclear Information System (INIS)

(1978). United States Quan, B. Becker, M. Harris, DR Rensselaer Polytechnic

UK PubMed Central (United Kingdom)

The cell cycle-regulatory transcription factor E2F-1 is regulated by interactions with proteins such as the retinoblastoma gene product and by cell cycle-dependent alterations in E2F-1 mRNA abundance....Full Text Available

International Nuclear Information System (INIS)

The fuel management study on 18-months fuel cycle project is introduced for Daya Bay Nuclear Power Station. Station from the selection of the objective of fuel management for 18-months cycle, the method used and the analysis done are explained in detail to reach the final loading pattern chosen

International Nuclear Information System (INIS)

18-Months cycle reload design verifications of Daya Bay NPS is briefly described. It was attempted giving the description of analysis scope and key technology for a nuclear power plant which will be changed fuel management strategy from one year to 18-months cycle

CERN Document Server

Many sunspot cycles are double peaked. In 1967 Gnevyshev suggested that actually all cycles have two peaks generated by different physical mechanisms, but sometimes the gap between them is too short for the maxima to be distinguished in indices of the total sunspot activity. Here we show that indeed all cycles have two peaks easily identified in sunspot activity in different latitudinal bands. We study the double peaks in the last 12 sunspot cycles and show that they are manifestation of the two surges of toroidal field - the one generated from the poloidal field advected all the way on the surface to the poles, down to the tachocline and equatorward to sunspot latitudes, and another one generated from the poloidal field diffused at midlatitudes from the surface to the tachocline and transformed there into toroidal field. The existence of these two surges of toroidal field is due to the relative ...

International Nuclear Information System (INIS)

A series of hydrogenation/dehydrogenation cycles have been performed on palladium wire samples, stressed by a constant mechanical tension, in order to investigate the changes in electrical and mechanical properties. A large increase of palladium electrical resistivity has been reported due to the combined effects of the production of defects linked to hydrogen insertion into the host lattice and the stress applied to the sample. An increase of the palladium sample strain due to hydrogenation/dehydrogenation cycles in ????? phase transitions is observed compared to the sample subjected to mechanical tension only. The loss of initial metallurgical properties of the sample occurs already after the first hydrogen cycle, i.e. a displacement from the initial metallic behavior (increase of the resistivity and decrease of thermal coefficient of resistivity) to a worse one occurs already after the first hydrogen ...

British Library Electronic Table of Contents (United Kingdom)

Long life cycles covering more than one year are known for all orders of insects. There are different mechanisms of prolongation of the life cycle: (1) slow larval development; (2) prolongation of the adult stage with several reproduction periods; (3) prolongation of diapause; (4) combination of these mechanisms in one life cycle. Lasting suboptimal conditions (such as low temperature, low quality of food or instability of food resources, natural enemies, etc.) tend to prolong life cycles of all individuals in a population. In this case, the larvae feed and develop for longer than a year, and the active periods are interrupted by dormancy periods. The nature of this dormancy is unknown: in some cases it appears to be simple quiescence, in others it has been experimentally shown to be a tru...

International Nuclear Information System (INIS)

Tunable output wavelength is an important character of a free electron laser (FEL). As generally understood, to alter the wavelength of a high-gain harmonic generation (HGHG) FEL laser, the seed laser must be tunable. A few-cycle, high intensity laser obtained by optical compression usually has pretty broad bandwidth in the spectral domain, which can be used as the seed laser of a HGHG and may open the possibility to approach a HGHG scheme with fully tunable wavelength. In this paper, a HGHG FEL seeded by a few-cycle laser is theoretically discussed and numerically investigated. A few-cycle seed laser significantly influences HGHG FEL performance, especially in output wavelength tuning. For a HGHG FEL seeded by a 4-cycle 786 nm laser, output wavelength tunability range up to 14.9% of the central wavelength 262 nm is observed by adjusting the resonant condition.

International Nuclear Information System (INIS)

Japan's basic nuclear policy is to reprocess spent fuel and to effectively use the recovered plutonium and uranium. MOX fuel utilization in LWRs is promoted in 16-18 reactors by FY2015. Commercial operation of Rokkasho Reprocessing Plant is planned to start in 2012. Prototype reactor 'Monju' restarted operation in May 2010. From FY 2007, Fast Reactor Cycle Technology Development Project (FaCT project) started which focuses more toward the commercialization stage FBR cycle. Basic scenario of Japan's R and D aims for realization of demonstration FBR by around 2025 and introducing commercial FBRs before 2050. Smooth transition from LWR fuel cycle to FBR one is an important point. For nuclear fuel cycle which requires long term R and D, human resources development and keeping is vitally important. (author)

Energy Technology Data Exchange (ETDEWEB)

The Fast Flux Test Facility (FFTF) core loading during its ninth operating cycle was significantly different from that of previous cycles because of the presence of the Core Demonstration Experiment (CDE). The CDE consists of a number of axially blanketed fuel assemblies and internal blankets prototypic of advanced oxide cores in Liquid Metal Reactors (LMR). In preparation for the Cycle 9 reload design effort, a careful assessment of control rod worth and reactivity calculations for Cycles 1 through 8 was made. The goal of this study was to establish calculational biases and reduce uncertainties factored into the reload design calculations. These analyses helped assure that the operational objectives for Cycle 9 were met.

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the results of research conducted during the sixteen month continuation of a program to develop rechargeable zinc-air batteries for electric vehicles. The zinc-air technology under development incorporates a metal foam substrate for the zinc electrode, with flow of electrolyte through the foam during battery operation. In this ``soluble`` zinc electrode the zincate discharge product dissolves completely in the electrolyte stream. Cycle testing at Lawrence Berkeley Laboratory, where the electrode was invented, and at MATSI showed that this approach avoids the zinc electrode shape change phenomenon. Further, electrolyte flow has been shown to be necessary to achieve significant cycle life (> 25 cycles) in this open system. Without it, water loss through the oxygen electrode results in high-resistance failure of the cell. The Phase I program, which focused entirely on the zinc electrode, elucidated ...

Energy Technology Data Exchange (ETDEWEB)

The LiMnO{sub 2} lamellar oxide, obtained by exchange reaction from its sodium homologue {alpha}-NaMnO{sub 2}, has been used as a positive electrode for lithium batteries. After the first electrochemical cycle, the shape of the potential-composition curve changes and indicates a change in the structure. This modification changes imperceptibly at each cycle and after about 40 cycles, a stationary state is reached. Powder spectra refinement using the Rietvelt method shows a migration of manganese ions from the thin sheets towards the inter-sheet space. After a single cycle, 8% of the manganese ions are already present in the lithium site and this rate reaches 13% after 3 cycles. During long cycling, a redistribution of ions and vacancies inside the cfc oxygenated pile leads to a structure very similar to the LiMn{sub 2}O{sub 4} spinel. This structure evolution is ...

Energy Technology Data Exchange (ETDEWEB)

Sulfur poisoning from engine fuel and lube is one of the most recognizable degradation mechanisms of a NOx adsorber catalyst system for diesel emission reduction. Even with the availability of 15 ppm sulfur diesel fuel, NOx adsorber will be deactivated without an effective sulfur management. Two general pathways are currently being explored for sulfur management: (1) the use of a disposable SOx trap that can be replaced or rejuvenated offline periodically, and (2) the use of diesel fuel injection in the exhaust and high temperature de-sulfation approach to remove the sulfur poisons to recover the NOx trapping efficiency. The major concern of the de-sulfation process is the many prolonged high temperature rich cycles that catalyst will encounter during its useful life. It is shown that NOx adsorber catalyst suffers some loss of its trapping capacity upon high temperature lean-rich exposure. With the use of a disposable SOx trap to remove large portion of the sulfur ...

Science.gov (United States)

Although the German Molasse Basin can be regarded as a mature hydrocarbon province, no regional sequence stratigraphic analysis has been carried out so far. We have studied seismic lines and well data from the region between the Isar and Inn rivers (SE Germany) that have been generously supplied by German oil companies (DEE, BEB, Mobil, RWE-DEA and Wintershall). Initial work indicates that five major seismic sequences within three main depositional cycles are developed. The Alpine thrust belt to the south serves as the primary sediment source in the foreland basin. However, sedimentary infill mainly took place parallel to the basin axis. Our analysis suggests that the stratigraphic development of the Molasse Basin was mainly controlled by eustatic sea-level changes which caused the shoreline to shift in the W-E direction. The shifting of the depocenter axis in a N-S direction was controlled by the tectonic evolution of the thrust belt. The sea-level curve ...

Energy Technology Data Exchange (ETDEWEB)

A procedure is described for modeling the choices made in urban American households among personal vehicles on the bases of cost, passenger capacity, and engine technology, and it projects those preferences to the year 1990 and 2000. The results of this disaggregate technique are used by the other predictive research tasks undertaken by Argonne National Laboratory in a project entitled Technology Assessment of Productive Conservation in Urban Transportation (TAPCUT). The vehicle preferences reported here furnish data for the overall TAPCUT objective of forecasting the probable effects of energy conservation policies in transportation. In our projections, vehicles with standard spark-ignition (Otto-cycle) engines continue to dominate automobile holdings and new car purchases in either of two socioeconomic scenarios under any of three settings (an existing policy set and two alternative conservation strategies). From 1990, small cars (seating ...

Science.gov (United States)

The transcriptional silencing of some cell cycle inhibitors and tumor suppressors, such as p16 and retinoic acid receptor beta(2), by DNA hypermethylation at CpG islands is commonly found in human oral squamous carcinoma cells. We examined the effects of the DNA methyltransferase inhibitor 5-Aza-2'-deoxycytidine (5-Aza; 0.25 mg/kg body weight), all-trans retinoic acid (RA; given at 100 microg/kg body weight and 1 mg/kg body weight), and the combination of 5-Aza and the low-dose RA on murine oral cavity carcinogenesis induced by the carcinogen 4-nitroquinoline 1-oxide (4-NQO) in a mouse model. All the drug treatments were done for 15 weeks after a 10-week 4-NQO treatment. Mice in all drug treatment groups showed decreases in the average numbers of neoplastic tongue lesions. The combination of 5-Aza and RA effectively attenuated tongue lesion severity. Although all drug treatments limited the increase in the percentage of proliferating cell ...

CERN Document Server

Statistical modelling for social researchers

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to determine the thermal reliability of stearic acid, palmitic acid, myristic acid and lauric acid as latent heat energy storage materials with respect to various numbers of thermal cycles. The fatty acids, as phase change materials (PCMs), of industrial grade (purity between 90% and 97%) were subjected to accelerated thermal cycle tests. The differential scanning calorimetry (DSC) analysis technique was applied to the PCMs after 0, 120, 560, 850 and 1200 melt/freeze cycles in order to measure the melting temperatures and the latent heats of fusion of the PCMs. The DSC results indicated that the change in melting temperature for the PCMs was in the range of 0.07-7.87 deg. C, and the change in latent heat of fusion was -1.0% to -27.7%, except for stearic acid between 560 and 1200 melt/freeze cycles. However, the decrease in the latent heats of fusion for all the PCMs was not ...

CERN Document Server

There are various interesting semantics' (extensions) designed for argumentation frameworks. They enable to assign a meaning, e.g., to odd-length cycles. Our main motivation is to transfer semantics' proposed by Baroni, Giacomin and Guida for argumetation frameworks with odd-length cycles to logic programs with odd-length cycles through default negation. The developed construction is even stronger. For a given logic program an argumentation framework is defined. The construction enables to transfer each semantics of the resulting argumentation framework to a semantics of the given logic program. Weak points of the construction are discussed and some future continuations of this approach are outlined.

Energy Technology Data Exchange (ETDEWEB)

The restricted temperature stability of the synthetic thermal oil which is used as heat carrier fluid in parabolic trough collectors so far limits the live steam parameters in the steam cycle to approximately 375 Celsius. In order to break through this limit, already for quite some time it is researched to replace the thermal oil by boiler feeding waters and to accomplish the evaporation in the collectors. The contribution under consideration gives an overview on the direct evaporation concept and summarizes the past operational experiences. Moreover, the challenges with the integration of this technology in a steam turbine cycle are elaborated.

Energy Technology Data Exchange (ETDEWEB)

National Power is building its first gas turbine combined cycle power station at Killingholme, situated to the south of the River Humber in the East of England. NEI ABB Gas Turbines Limited was awarded the turnkey contract in July 1990 to build a nominal 650 MW combined cycle power station based around three Asea Brown Boveri GT13E gas turbines. The project is outlined in this article. The plant is due for completion in July 1993. (author)

International Nuclear Information System (INIS)

According to China's 'Medium- and Long-term Nuclear Power Development Program (2005-2020)', nuclear energy development in China will take the technical line of closed nuclear fuel cycle. This paper discusses the significance of closed nuclear fuel cycle, and briefly introduces development trends in the world. This article also discusses the opportunity to construct spent fuel reprocessing plant; equilibrium of plutonium production and consumption; adaptability and economics to use MOX fuel in the thermal neutron reactor. Some suggestions are put forward to the overall development of nuclear energy in China. (authors)

Energy Technology Data Exchange (ETDEWEB)

Condensing curves are presented for a number of two-component mixed hydrocarbon working fluids which are potentially usable in binary geothermal cycles. Performance of geothermal thermodynamic cycles incorporating these fluids has been evaluated under separate cover; two figures summarizing the results of those evaluations have been included here for continuity. The purpose of this report is: first, to document the condensing curves which were used in the mixed fluid cycle analyses, and second, to provide background useful in the preliminary evaluation of heat rejection systems for advanced geothermal electric power plants utilizing mixed hydrocarbon working fluids. Some concluding remarks are presented.

Energy Technology Data Exchange (ETDEWEB)

Desiccant cooling is a potentially environmentally friendly technology that can be used to condition the internal environment of buildings. Unlike conventional air conditioning systems, which rely on electrical energy to drive the cooling cycle, desiccant cooling is a heat-driven cycle. This paper follows on from an initial study by the authors, and uses real meteorological data to evaluate the potential in the United Kingdom of using solar energy to drive the desiccant cooling cycle. Through the use of parametric studies, the paper investigates the energy consumption and costs associated with desiccant cooling. (author)

Science.gov (United States)

2.1 The Importance of Life Cycle Management and Cost Estimating................. ........... 1-2 .... 4.3.5 Task 12: Update Cost Estimate on Regular Basis. ...

Energy Technology Data Exchange (ETDEWEB)

The Integral Fast Reactor is an innovative liquid metal reactor concept that is being developed by Argonne National Laboratory. It takes advantage of the properties of metallic fuel and liquid metal cooling to offer significant improvements in reactor safety, operation, fuel cycle economics, environmental protection, and safeguards. The plans for demonstrating the IFR fuel cycle, including its waste processing options, by processing irradiated fuel from the Experimental Breeder Reactor-II fuel in its associated Fuel Cycle Facility have been developed for the first refining series. This series has been designed to provide the data needed for the further development of the IFR program. An important piece of the data needed is the recovery of TRU material during the reprocessing and waste operations.

Energy Technology Data Exchange (ETDEWEB)

The removal of toxic metals and alkalis from gas streams at high temperatures was investigated. This is important for the development of coal-fired combined cycle power generation systems.

Energy Technology Data Exchange (ETDEWEB)

Short communication

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the charging mode of an in-series assembly of lithium-carbon battery cells, a test has been performed on 5 commercial cells (18650) of 0.95 Ah nominal capacity. Results show that it is possible to cycle the cells at 80% of their output capacities during more than 2000 cycles. The management of the battery consists in maintaining a constant battery voltage as soon as a cell reaches its limit voltage during constant current charging. The initial dispersion of cells has been maintained practically constant during the cycling and the charge state of all cells has decreased progressively. (J.S.)

UK PubMed Central (United Kingdom)

Questionnaires and twice daily peak expiratory flow measurements were used to evaluate the effects of the menstrual cycle in asthmatic women. Forty per cent of women reported premenstrual deterioration...Full Text Available

Science.gov (United States)

... The C-130J is a modification of the C-130H, undertaken by Lockheed Martin Aeronautics Corporation (LMAC) as a private ven- ture, with intended ...

Science.gov (United States)

These include, but are not limited to: stellar winds and outflows, post-main- sequence star evolution, binary star evolution, globular cluster structure and ...

British Library Electronic Table of Contents (United Kingdom)

Urban heritage areas throughout the world have experienced cycles of neglect and upgrade that were at times intentional and at other times due to economic difficulties or an unbalanced ideological focus on technological, social or political developments. Modernism of the early and mid-1900s was clearly against keeping heritage areas as they were perceived to hinder future developments. Postmodernist thinking afterwards was more sympathetic to heritage as a means of countering the 'placelessness' of the modern city. Global appreciation of urban heritage and the world's cultural diversity at the end of the century made the occurrence of 'physical neglect' cycles very unlikely in the future. This research paper takes the stand that urban planners and designers face cycles of higher or lower u...

UK PubMed Central (United Kingdom)

This Memorandum, after summarizing the life cycle of the different species of human schistosome, reviews the present knowledge of the immunology of schistosomiasis. Each stage of the parasite contains...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The Heat Cycle Research Program, which is conducted for the Department of Energy, has as its objective the development of the technology for effecting the improved utilization of moderate temperature geothermal resources. The current testing involves the investigation of binary power cycle performance utilizing mixtures of non-adjacent hydrocarbons as the working fluids, with supercritical vaporization and in-tube condensation of the working fluid. The utilization of these concepts verified here will improve the net geofluid effectiveness (net watt hours plant output per pound of geofluid) about 20% over that of a conventional binary power plant. The major effect in this improvement is the ability to achieve integral, countercurrent condensation. Results are presented for the recent testing including those tests examining the performance of the countercurrent condenser at different tube inclinations and comparison with new design-base computer ...

Energy Technology Data Exchange (ETDEWEB)

This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data are presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed.

British Library Electronic Table of Contents (United Kingdom)

A small fleet of classic London Taxis (Black cabs) equipped with hydrogen fuel cell power systems is being prepared for demonstration during the 2012 London Olympics. This paper presents a Life Cycle Analysis for these vehicles in terms of energy consumption and CO2 emissions, focusing on the impacts of alternative vehicle technologies for the Taxi, combining the fuel life cycle (Tank-to-Wheel and Well-to-Tank) and vehicle materials Cradle-to-Grave. An internal combustion engine diesel taxi was used as the reference vehicle for the currently available technology. This is compared to battery and fuel cell vehicle configurations. Accordingly, the following energy pathways are compared: diesel, electricity and hydrogen (derived from natural gas steam reforming). Full Life Cycle Analysis, usin...

Energy Technology Data Exchange (ETDEWEB)

During the service in nuclear power plants, steam generator (SG) tubing will suffer from a vibration with a frequency from 30-40 Hz. This means that SG tubing will undergo a very high cycle fatigue process during the design life time (25 years=about 3x10{sup 10}cycles). The material degradation and the very high cycle fatigue life of SG tubing materials due to the vibration are therefore of concern. In this investigation, the fatigue properties of Alloy 690 and Alloy 800 SG tubing in the very high cycle fatigue regime (higher than 10{sup 7} cycles) and strain controlled fatigue at temperatures up to 330{sup o}C have been investigated. The fatigue properties of SG tubing of Alloy 690 are comparable to that of wrought material. The strain controlled fatigue properties of Alloy 690 and Alloy 800 are slightly better at 288{sup o}C than at room temperature (RT). At the stress near the ...

Energy Technology Data Exchange (ETDEWEB)

A test program was conducted under contract to Sandia National Laboratories to investigate water/steam effects on elevated temperature low cycle fatigue and creep-fatigue of Alloy 800. This report presents interpretation and analysis of the test results. Tubular specimens with water sealed inside were cycled to failure under strain control. Tests were conducted to 616K (650/sup 0/F) and 922K (1200/sup 0/F); some at 922K included tensile or compressive hold periods to simulate creep-fatigue conditions. The tubular specimens showed significantly lower lives than solid bar specimens cycled at equivalent strain ranges. Rough internal surfaces contributed to early crack initiation with these specimens. Inclusion of hold periods caused further large reductions in cycles to failure.

UK PubMed Central (United Kingdom)

BackgroundSenescence is integral to the flowering plant life-cycle. Senescence-like processes occur also in non-angiosperm land plants, algae and photosynthetic prokaryotes. Increasing...Full Text Available

International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

CERN Document Server

We investigate the chemical and observational implications of repetitive transient dense core formation in molecular clouds. We allow a transient density fluctuation to form and disperse over a period of 1 Myr, tracing its chemical evolution. We then allow the same gas immediately to undergo further such formation and dispersion cycles. The chemistry of the dense gas in subsequent cycles is similar to that of the first, and a limit cycle is reached quickly (2 - 3 cycles). Enhancement of hydrocarbon abundances during a specific period of evolution is the strongest indicator of previous dynamical history. The molecular content of the diffuse background gas in the molecular cloud is expected to be strongly enhanced by the core formation and dispersion process. Such enhancement may remain for as long as 0.5 Myr. The frequency of repetitive core formation should strongly determine the level of background ...

Energy Technology Data Exchange (ETDEWEB)

Considering beryllium as plasma facing armour this paper presents recent results obtained in Russia. A special process of joining beryllium to a Cu-alloy material structure is described and recent results of thermal cycling tests of such joints are presented. Summarizing the results, the authors show that a Cu-alloy heat sink structure armoured with beryllium can survive high heat fluxes ({>=}10 MW/m{sup 2}) during 1000 heating/cooling cycles without serious damage to the armour material and its joint. The principal feasibility of thermal cycling of beryllium grades and their joints directly in the core of a nuclear reactor is demonstrated and the main results of this test are presented. The paper also describes the thermal cycling of different beryllium grades having cracks initiated by previously applied high heat loads simulating plasma disruptions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Fact sheet written for the NICE3 Program on a new chlorine-free process for pulping and bleaching wastewater.

Science.gov (United States)

Hamed, A. and A. Mohamed, "Assessment of Shock Induced Flow Separation and ...... AGARD Symposium on Combined Cycle Propulsion for Hypersonic Application, ...

British Library Electronic Table of Contents (United Kingdom)

Research in concentrated thermal solar power plants of all types and, in particular, those based on central receiver, namely solar tower plants, has experienced great impetus in the last decade, reaching full commercial operation with the PS10 plant in Spain. In spite of previous demonstration plants testing different receivers and power cycle layouts, this first commercial power plant adopted a cavity receiver generating saturated steam and therefore penalising cycle efficiency in order to gain plant reliability. According to the experience gained, if a competitive Levelised Cost of Electricity is to be reached, capital and maintenance costs must be reduced and efficiencies must be increased. To achieve these goals, modifying the power cycle is deemed essential, whether using superheated ...

Science.gov (United States)

... of the cycle shows that the separation area ea. ... with suitable flow solvers based on the Reynolds ... AGARD 75th Fluid Dynamics Panel Meeting and ...

Energy Technology Data Exchange (ETDEWEB)

This report documents the technical development for a patent disclosure of a double-clad process for the continuous casting of thin-strip carbon steel. The fundamental idea of the disclosure is to form a product strip by depositing molten steel between two, cooled, clad strips of the same material. The claimed benefits include: (a) the conservation of energy in steel making through the elimination of soaking pits and reheat cycles, and (b) an improved surface on both sides of the as-cast product such that it will be suitable for direct feed to a cold-reduction mill. However, the process as conceived is not necessarily limited to the casting of carbon steel, but may be also applied to other metals and alloys. The work is described under three headings as follows. Preliminary Considerations and Scoping Analysis presents the basic idea of the double-clad, thin-strip casting process; the energy conservation potential; scoping heat transfer calculations for the casting ...

Science.gov (United States)

The bed nucleus of the stria terminalis (BST) and the medial amygdala (MeA) are anatomically connected sites necessary for chemosensory regulation of social behaviors in rodents. Prairie voles (Microtus ochrogaster) are a valuable model for studying the neural regulation of social behaviors because, unlike many other rodents, they are gregarious, pair bond after copulating, and are biparental. We herein describe sex and species differences in immunoreactivity for tyrosine hydroxylase (TH), the rate-limiting enzyme for catecholamine synthesis, in the BST and MeA. Virgin male prairie voles had a large number of TH-immunoreactive cells in areas analogous to the rat principal nucleus of the BST (pBST) and the posterodorsal medial amygdala (MeAPd). Virgin female prairie voles had far fewer TH-immunoreactive cells in these sites ( approximately 17% of the number of cells as males in the pBST, approximately 35% of the number of cells in the MeAPd). A few TH-immunoreactive ...

Science.gov (United States)

Decadal-scale climate variations over the Pacific Ocean and its surroundings are strongly related to the so-called Pacific decadal oscillation (PDO) which is coherent with wintertime climate over North America and Asian monsoon, and have important impacts on marine ecosystems and fisheries. In a near-term climate prediction covering the period up to 2030, we require knowledge of the future state of internal variations in the climate system such as the PDO as well as the global warming signal. We perform sets of ensemble hindcast and forecast experiments using a coupled atmosphere-ocean climate model to examine the predictability of internal variations on decadal timescales, in addition to the response to external forcing due to changes in concentrations of greenhouse gases and aerosols, volcanic activity, and solar cycle variations. Our results highlight that an initialization of the upper-ocean state using historical observations is effective ...

International Nuclear Information System (INIS)

Combination of radiotherapy and chemotherapy (CRC) is actually one important way of research in oncology. Theoretical advantages are: (1) Spatial cooperation; (2) Additivity, which is only obtained if the toxicity of each modality are different; (3) Supra-additivity, which needs a rigorous in vitro definition; the only way to prove it is to make an isobologram analysis. This model has however, some limitations: qualitative variable could not be used, results could be different, depending on the cell line and isoeffect chosen...In fact, a supra-additivity was only demonstrated for cis platinum and etoposide. Interactions mechanisms were: (1) at the molecular level, creation of new lesions or inhibition of radiation lesions repair; (2) At the cellular level, either cytokinetic cooperation with S-phase dependent drugs, or synchronization for the drugs which blocked the cells in M-phase; (3) At the tissular level, reoxygenation, cycle ...

International Nuclear Information System (INIS)

This paper describes an approach to solve air quality problems which frequently occur during iterations of the baseline change process. From a schedule standpoint, it is desirable to perform this evaluation in as short a time as possible while budgetary pressures limit the size of the staff available to do the work. Without a method in place to deal with baseline change proposal requests the environment analysts may not be able to produce the analysis results in the time frame expected. Using a concept called the Rapid Response Air Quality Analysis System (RAAS), the problems of timing and cost become tractable. The system could be adapted to assess other atmospheric pathway impacts, e.g., acoustics or visibility. The air quality analysis system used to perform the EA analysis (EA) for the Salt Repository Project (part of the Civilian Radioactive Waste Management Program), and later to evaluate the consequences of proposed baseline changes, consists of three components: Emission source ...

Energy Technology Data Exchange (ETDEWEB)

This report contains preconceptual designs and planning level life-cycle cost estimates for managing hazardous waste. The report`s information on treatment, storage, and disposal modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the US Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report.

Energy Technology Data Exchange (ETDEWEB)

Equations are derived to permit calculation of the work required for the isentropic compression of a two phase fuel-air mixture. Methanol evaporation during compression is shown to substantially reduce compression work and thereby improve cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. 14 refs.

Wastenet

... Space weather is the biggest driver of ozone depletion and much else we are only beginning to understand. Solar Cycle 24 may turn out to be weak in terms of sun spot count but the amount of energy delivered by CME/SPE will probably not be. Remember that the Carrington Event in 1859 happened during a cycle with a lowish sun spot count. Recommend (1) Report abuse ...

Wastenet

... As a consequence the Brazilian government introduced a thermoelectric priority programme covering the construction of new gas fired combined cycle power plants. One such plant has been constructed at the Suape industrial port complex in the state of Pernambuco. The US$350 million Termopernambuco combined cycle gas ...

Energy Technology Data Exchange (ETDEWEB)

The present invention provides an improvement in the art of combined steam turbine and gas turbine power plants of the type wherein the principal source of energy is a fluidized bed combustor fueled by coal. More specifically, the invention pertains to supplemental firing of the gas turbine cycle with a clean hydrocarbon fuel (CHF) at a high incremental efficiency to significantly increase overall plant efficiency.

British Library Electronic Table of Contents (United Kingdom)

Cycling parameters (reversible specific capacity, first-cycle coulombic efficiency, accumulated irreversible capacity, and reversible capacity retention) of hybrid electrodes based on mechanical mixtures of a silicon nanopowder with KS6 and MAG-20 synthetic graphites and binders of varied nature were subjected to an integrated analysis in comparison with graphite electrodes.

Energy Technology Data Exchange (ETDEWEB)

The systems analyses and optimization studies performed in connection with a program to design and evaluate a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion and advanced technology in the hot gas cleanup system and gas turbines are presented. Details on the plant control system are included. (LCL)

International Nuclear Information System (INIS)

The use of nuclear reactors to provide electrical energy has shown considerable growth since the first nuclear plant started commercial operation in the mid 1950s. Although the main purpose of this paper is to review the fuel cycle capabilities in the United States, the introduction is a brief review of the types of nuclear reactors in use and the world-wide nuclear capacity.

CERN Document Server

We prove a uniqueness result for limit cycles of the second order ODE $\\ddot x + \\sum_{j=1}^{J}f_{j}(x)\\dot x^{j} + g(x) = 0$. We extend a uniqueness result proved in \\cite{CRV}. The main tool applied is an extension of Massera theorem proved in \\cite{GS}.

Energy Technology Data Exchange (ETDEWEB)

The detailed sequence stratigraphic analysis of the siliciclastic-dominated Late Cretaceous sediments (Aren Sandstone and Garumnian red beds, south central Pyrenees, Spain) reveals the repeating disposition of critical elements and controlling mechanisms of cycles and sequences. Our approach integrates (a) hierarchy of unconformity-bounded units, (b) physical expression of boundaries traceable from the continent to the basin, (c) featuring facies and depositional systems, (d) well log and seismic expression, and (e) driving basing-filling mechanisms. A comparison to other active basins is suggested in order to prove the validity beyond the regional scale. Four basin-wide transgressive facies cycles were identified and interpreted as third-order units. The transgressive phase of each cycle is represented by mixed shelf deposits, while regressive periods consists of complex delta systems. The cycles are ...

Energy Technology Data Exchange (ETDEWEB)

The method of life-cycle assessment (LCA) has been applied to cars with different power trains. As an example, the results for greenhouse gas (GHG) emissions are presented. They show possibilities and limits for the reduction of these emissions in the transportation sector by means of advanced technology. (author) 2 figs., 4 refs.

International Nuclear Information System (INIS)

The author describes the feasibility study on implementing 18-months fuel cycle project in Daya Bay NPP: content, steps and major results including objective determination, benefit/cost assessment, electric net demands investigation, risk assessment, technical targets

Energy Technology Data Exchange (ETDEWEB)

The externally fired combined cycle is emerging as an economically viable repowering options for old non-competitive coal fired steam plants. This paper describes the initial operation of a pilot plant located at Kennebunk, Maine and the initial work on the repowering of a 48MW coal fired steam plant located in Warren, PA.

Energy Technology Data Exchange (ETDEWEB)

The use of pressurised fluidized-bed coal combustion (fbc) in a combined cycle is seen as a most attractive technology for increasing the efficiency of electricity generation. The concept of pressurised fbc is described and the technical problems that are encountered in its operation and in limiting it to a gas turbine are discussed. Details are given of pilot plant facilities and current R and D programmes.

Energy Technology Data Exchange (ETDEWEB)

A dual-boiling isobutane cycle was selected for the present 5-megawatt (5MW) Raft River Pilot Plant to utilize the lower-temperature geothermal resources (near 300F). This study represents a second effort directed toward the design of an improved binary geothermal electric plant suitable for utilization of the lower temperature resources. 7 refs.

Energy Technology Data Exchange (ETDEWEB)

The sulfur-iodine water-splitting cycle is characterized by the following three reactions: 2H/sub 2/O + SO/sub 2/ + I/sub 2/ ..-->.. H/sub 2/SO/sub 4/ + 2HI; H/sub 2/SO/sub 4/ ..-->.. H/sub 2/O + SO/sub 2/ + 1/2 O/sub 2/; and 2HI ..-->.. H/sub 2/ + I/sub 2/. This cycle was developed at General Atomic after several critical features in the above reactions were discovered. These involved phase separations, catalytic reactions, etc. Estimates of the energy efficiency of this economically reasonable advanced state-of-the-art processing unit produced sufficiently high values (to approx.47%) to warrant cycle development effort. The DOE contract was largely directed toward the engineering development of this cycle, including a small demonstration unit (CLCD), a bench-scale unit, engineering design, and costing. The work has resulted in a design that is projected to produce H/sub 2/ at prices not yet ...