Science.gov (United States)

We attempt to image the rupture propagation of the 2004 M6.0 Parkfield earthquake by analyzing records from the USGS Parkfield seismic array (UPSAR) and other strong-motion stations. The UPSAR array consists of 12 stations distributed over about one square kilometer at a distance of 10~km from the San Andreas fault near Parkfield, California. We employ a method that uses reverse time migration to stack the seismograms at back-projected locations along the fault. We use waveform cross-correlation to align the initial P-wave arrivals and correct for small static time shifts in the records. This forces a coherent image at the hypocenter at the quake origin time. Initial results at later time steps show some evidence of the expected rupture propagation to the north. However, the resolution of the back-projection is limited by the small aperture of the UPSAR array. Records from other ...

Science.gov (United States)

According to the California Earthquake Authority, only about 12% of current California residences are covered by any form of earthquake insurance, down from about 30% in 1996 following the 1994, M6.7 Northridge earthquake. Part of the reason for this decreasing rate of insurance uptake is the high deductible, either 10% or 15% of the value of the structure, and the relatively high cost of the premiums, as much as thousands of dollars per year. The earthquake insurance industry is composed of the CEA, a public-private partnership; modeling companies that produce damage and loss models similar to the FEMA HAZUS model; and financial companies such as the insurance, reinsurance, and investment banking companies in New York, London, the Cayman Islands, Zurich, Dubai, Singapore, and elsewhere. In setting earthquake insurance rates, financial companies rely on models like HAZUS, that ...

Science.gov (United States)

The Eagle Flat basin, an intermontane basin in Trans-Pecos Texas, is being considered as a possible site for the Texas repository of low-level radioactive wastes. Intermontane basins and associated normal faults formed in response to Basin and Range tectonism that began about 24 Ma ago. The most active late Tertiary and Quaternary faults occur within the Hueco Bolson (HB) and the Salt Basin/Salt Flat/Lobo Valley, west and east, respectively, of the proposed repository. Several faults of the southeast HB which are within 50 km of the site, displace middle Pleistocene deposits 10 to 24 m. The most recent surface rupture in the southeast HB probably occurred on the Amargosa fault during the Holocene. Upper Pleistocene deposits are offset 2.5 to 4.5 m, and middle Pleistocene deposits are displaced 24 m. Fault scarps within 50 km east of the proposed repository are associated with faults bounding the Salt Basin/Salt Flat/Lobo Valley. In the southern Salt Basin and ...

Energy Technology Data Exchange (ETDEWEB)

A sodium-water reaction drove from the single tube break in steam generator of FBR might overheat labor tubes rapidly under internal pressure loadings. If the temperature of tube wall becomes too high, it has to be evaluated that the stress of tube does not exceed the material strength limit to prevent the propagation of tube rupture. This study clarified the tensile and creep properties of Mod.9Cr-1Mo steel at ultra-high temperature which will be used in evaluation of the tube burst by sodium-water reaction. The strain rates for tensile test are from 10%/min to 10%/sec, and creep-rupture time is maximum 277sec. The range of test temperature is 700degC to 1300degC. The main results obtained were as follows; (1) The evaluation data on the relationship between tensile strength and strain rate and creep-rupture strength in shorter time on Mod.9Cr-1Mo steel were acquired. (2) Short-term mechanical ...

Science.gov (United States)

Aug 23, 2011 ... Earthquakes, Hurricanes and Stubborn Instruments ... And if earthquakes and stubborn instruments aren't enough, there's this giant hurricane ...

Transactions and Proceedings of the Royal Society of New Zealand 1868-1961

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The regular occurrence of large-scale earthquakes in Japan necessitates the use of earthquake disaster prevention systems that focus on gathering damage information on gas supply facilities immediately after an earthquake strikes and minimizing the damage. This paper discussed the development of an earthquake damage estimation system for city gas pipelines that can show damage information in real-time by using earthquake records obtained from densely deployed earthquake observation networks and the most advanced telecommunication and information technologies. The paper summarized the earthquake damage estimation system (EDES) and Toho Gas disaster prevention measures. Specific topics that were discussed included the Toho Gas supply method; earthquake countermeasures; construction of computer systems; normal and emergency ...

Science.gov (United States)

Plate-boundary earthquakes have occurred repeatedly in the past several thousand years at the Cascadia subduction zone, where they are widely recorded ... ...

International Nuclear Information System (INIS)

A detailed assessment of the FFTF Primary Heat Transport System (PHTS) piping has led to the conclusion that the integrity of the piping is assured such that there is no realistic potential for a rupture. Nevertheless, consistent with the practice of showing design margins even for hypothetical events, a spectrum of postulated PHTS ruptures has been analyzed. The analyses showed that upstream of the reactor vessel inlet downcomer, rupture areas of any size including a double-ended rupture could be tolerated with no core coolant boiling. At the most limiting location, the reactor inlet nozzle, rupture areas of 75 in."2 and 55 in."2 could be tolerated for three-loop and two-loop operation, respectively. This paper will present the following: (1) the criterion with which consequences of postulated pipe ruptures are compared; (2) the general transient response of ...

Norwegian Open Research Archives (NORA)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Modelization of crack propagation and theoretical prediction of rupture are the two main objectives of researchers in stress corrosion cracking. Nevertheless, to reach this aim, the behavior of the passive film which appears spontaneously on the substrate in contact with an environment has to be known. This structural and mechanical characterization is all the more difficult because the number of parameters is important: crystallinity rate, defects concentration, thickness (about a few nanometers), electric field, chemical composition (a lot of oxides are present), peeling layers (atomic structure for example) and some hypothesis can be made about their multi-layer structure, their chemical composition or their epitaxial character... Passive films formed on 316L or 304L stainless steels in different aqueous solutions (in ambient air, in MgCl{sub 2} at 117 deg. C...) have been studied and some important remarks about their mechanical properties ...

UK PubMed Central (United Kingdom)

Spontaneous rupture of membranes (ROM) is a normal component of labor and delivery. Premature ROM (PROM) refers to rupture of the fetal membranes prior to the onset of labor irrespective of gestational...Full Text Available

Science.gov (United States)

Structural complexities reduce the homogeneity necessary for a site characterization model to an unacceptable level for performance assessment for radioactive waste disposal sites. The proposed site lies between the northern, stable Diablo platform and the southern, mobile Mesozoic Chihuahua tectonic belt. Structural movement along this interface has been active for the past 14,000 years. In addition, the area lies along the northern margin of the Permian Marfa basin and the northeastern margin of the deeply faulted Hueco bolson segment of the late Cenozoic Rio Grande rift system. Recent seismic activity with extensive surface rupture in Quitman Canyon (30 mi southeast of the site) is also documented from the 1931 Valentine, Texas, earthquake (6.4 Richter scale). The site is underlain by either a thrust fault or the complex terminus of a Mesozoic thrust fault. This fault is a segment of the continuous thrust sheet extending from exposures in ...

Science.gov (United States)

Not Available

Science.gov (United States)

125 Years of Science for America - 1879 to 2004 link to Western Coastal and Marine Geology website U.S. Geological Survey Professional Paper 1687 Marine Geology and Earthquake...

UK PubMed Central (United Kingdom)

The devastating earthquake in Sichuan, China on 12 May 2008 left thousands of survivors requiring medical care and intensive rehabilitation. In view of this great demand, the Chinese Speaking Orthopaedic...Full Text Available

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

In this paper, the authors describe the characteristics of design seismic input motions and recently observed seismic records of base isolated buildings in Japan. First, we describe some seismic design spectra for building structures which were adopted. Then we show response spectra and energy spectra of observed records obtained during two recent major earthquakes (The 1995 Hyogo-ken Nanbu Earthquake and the 2003 Tokachi-oki Earthquake), which demonstrate the effectiveness of base isolation against large amplitude earthquake ground motion. We also introduce the responses of base isolated buildings during some earthquakes including the Tokachi-oki Earthquake. These data were gathered through questionnaires sent to many engineers who had conducted response observations of base isolated buildings. Last, an example of a base isolated building on soft ground is ...

UK PubMed Central (United Kingdom)

A 33-year-old man sustained an acute Achilles tendon rupture which was surgically repaired. Early nonweight-bearing range of motion and strengthening of the ankle and the repaired muscle unit was allowed...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundTracheal rupture is a rare but life-threatening complication that most commonly occurrs after blunt trauma to the chest, but which may also complicate tracheal intubation....Full Text Available

UK PubMed Central (United Kingdom)

An 11-year-old mare presented 36 hours after foaling with a ruptured bladder. Uroperitoneum was diagnosed on ultrasound and from the creatinine concentration of the peritoneal fluid. Bladder endoscopy...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Reactor pressure vessel (RPV) steels are subjected to neutron irradiation at a temperature of about 290 deg C. This radiation exposure alters the mechanical properties, leading to a shift of the brittle-to-ductile transition temperature toward higher temperatures and to a diminution of the rupture energy as determined by Charpy V-notch tests. This radiation embrittlement is one of the important aging factors of nuclear power plants. U.S. NRC recommended the basic requirements for the determination of the pressure vessel fluence by regulatory guide DG-1025 in order to reduce the uncertainty in the determination of neutron fluence calculation and measurements. The determination of the pressure vessel fluence is based on both calculations and measurements. The fluence prediction is made with a calculation and the measurements are used to qualify the calculational methodology. Because of the importance and the difficulty of these calculations, the method`s ...

Science.gov (United States)

Hayakawa et al. (2009) and Hayakawa (2011) have recently reviewed some "anomalous" ULF signatures in the geomagnetic field which previous publications have claimed to be earthquake precursors. The motivation of this review is "to offer a further support to the definite presence of those anomalies". Here, these ULF precursors are reviewed once again. This brief communication shows that the reviewed anomalies do not "increase the credibility on the presence of electromagnetic phenomena associated with an earthquake" since these anomalous signals are actually caused by normal geomagnetic activity. Furthermore, some of these ULF precursors have just been rebutted by previous publications.

Energy Technology Data Exchange (ETDEWEB)

In this study, the two methods, US NRC and JAERI method, for the determination of scenario earthquakes for seismic design of nuclear power plants based on the probabilistic seismic hazard analysis were reviewed. The scenario earthquakes were developed for the Wolsung NPP site using the PSHA results based on the US NRC Regulatory Guide 1.165 procedures. It seems that the JAERI method is more appropriate to incorporate the effects of individual seismic sources and active faults, and to estimate the multiple ground motion parameters. The magnitude and distance bins of the scenario earthquakes for Wolsung NPP site were M6.4, 9km and M6.2, 13km.

Science.gov (United States)

Mar 2, 2010 ... The NASA/JPL Education Office works with educators -- both classroom teachers and informal educators -- to provide tools, resources and ...

International Nuclear Information System (INIS)

Purpose: To prevent structure material meltdown upon rupture of cooling pipeways in a impurity remover by preventing the coolants from flowing into the vacuum vessel while continuing the supply of coolants to other portions to be cooled. Constitution: Dual cooling pipeway systems are disposed to the neutralizing plates of the impurity remover. A rupture detector (pressure gage) is mounted to each of the cooling pipeways and flow rate control valves to be opened and closed by the signal from the detector are disposed to the upstream and downstream of the cooling pipeway. In this constitution if the cooling pipes should be ruptured, the coolant supply is stopped to the ruptured system in which the flow rate valve is closed by the signal from the rupture detector. However, since the coolant is kept to be supplied to the other system of the cooling pipeways, meltdown of the neutralizing ...

British Library Electronic Table of Contents (United Kingdom)

`Success' or `Red Splendor' plants propagated by shoot tip culture or embryogenesis had higher pollen germination than those propagated by cutting. All clones of `Pepride', `Peter Star' and `Nobel Star' propagated by cutting or by embryogenesis or shoot tip culture did not have viable pollen. `Peter Star' mutants through mutagenesis could recover pollen viability. When both parents were propagated by tissue culture, fruit set increased compared to when one or both parents were propagated by cuttings. Furthermore, the number of the harvested seeds doubled per pollination set, when the tissue culture parents were used instead of cutting-propagation plants.

Energy Technology Data Exchange (ETDEWEB)

A radon detector with LR-115 nuclear track film was constructed for radon concentration measurements in soil. Temporal radon variations, as well as the barometric pressure, precipitation and temperature were measured for two years. Negative correlation between radon concentration in soil and barometric pressure was found. For some of the recorded earthquakes that occurred during the observation period, soil radon anomalies may be noticed one month before the quakes.

Energy Technology Data Exchange (ETDEWEB)

The long-range correlation properties in the hourly time variability of geochemical signals measured in a 70 m depth well at Triponzo (Umbria region), are investigated by the detrended fluctuation analysis (DFA). DFA is a data processing method that allows for the detection of scaling behaviors in observational time series even in the presence of non-stationarities. The procedure adopted has allowed for the unambiguous identification of possible correlations among the recorded signals and local earthquakes.

International Nuclear Information System (INIS)

In an existent emergency reactor core cooling device, if a ruptures should occure in a pipeline of a gravitational dropping type reactor core cooling system pool (GDCS) due to some or other causes, a portion of GDCS pool water was flown out of the ruptured port and could not be used for reactor core cooling. Then, a difference pressure detector is disposed to a GDCS pipeline at the inlet of a reactor pressure vessel. When it is judged by the detector, that coolants flow to the outside of the injection pipeline, an injection value disposed to the GDCS pipeline is closed by the difference pressure signal. Even if a rupture should occur on the side of the pressure vessel at downstream to the check value of the GDCS pipeline, since backflow is caused at the pressure container inlet of the GDCS pipeline with the rupture port, the rupture is detected by the difference pressure detector to ...

Energy Technology Data Exchange (ETDEWEB)

The control of piece size in ruptured rocks in coal sections is important as part of the general problem of increasing efficiency in the technology of open-pit mining operations. An attempt is made in this paper to estimate the rupture capacity of exposed rocks in coal sections based on a set of physicomechanical property indicators, using the methods of multidimensional statistical analysis. It was established that all the parameters for the physiocomechanical properties of the exposed rocks are highly correlated. The method proposed for determining criteria for explosive capacity is of interest in developing criteria for the destruction capacity (drillability, excavation capacity, etc.) in the exposed rocks of coal sections which are characterized by high variation in physical and mechanical properties.

Science.gov (United States)

problem similar to the Stefan problem in heat conduction [19]. ..... as the Stefan problem. Although the Stefan problem and the creep rupture ...

International Nuclear Information System (INIS)

AISI 316L stainless steel was welded by the electron beam (EB) and laser techniques. Microstructural characteristics, hardness profile, creep rupture properties and creep damage of the welds were investigated. Fully austenitic microstructure was obtained in the two welds. The solidification structure of the welds consisted of the cellular and equiaxed dendrites. The creep rupture lives of the two welds were almost the same, and they were reduced by a factor of about two compared to the base metal. Moreover, the rupture elongation of the welds was lower than that of the base metal. Creep damage was observed in the ''parting'' region of the welds and in the heat-affected zone (HAZ), respectively. Final creep fracture occurred in the ''parting'' region of the welds. (orig.).

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Surface wave tomography method based on analysis of ambient noise is widely used during the last decade. It is assumed that correlated component of noise is composed of surface waves generated by sources distributed over the Earth's surface more or less uniformly. In such a case the cross-correlation function (CCF) at two stations may be considered as the Green's function of surface wave. This function should be symmetric relatively to zero time. However analysis of CCF at the stations located at the East-European Platform shows that as a rule CCF is characterized with a strong asymmetry. Since "purered noise cannot be extracted from seismic records due to superposition of earthquake signals, the method for calculation of CCF includes amplitude normalization for suppression of earthquakes that reduces signals from earthquakes to a noise level. The parts of records containing waves from earthquakes are ...

Energy Technology Data Exchange (ETDEWEB)

A geological and geotechnical framework was provided in order to facilitate understanding of the damage to structures resulting from soil conditions during the earthquake of January 17, 1995 at Hyogo-ken Nanbu (Kobe), Japan. Special attention was paid to the large scale failures of the quay walls in the port of Kobe, resulting from liquefaction. The performance of structures in improved and unimproved ground were compared. It was observed that locations with some previous site improvements through densification behaved satisfactorily, despite unanticipated high levels of ground motion. Soil-structure interaction problems, such as pile foundations, bridge piers, lifelines, and an underground subway station were also described. Reference was made to the significance of these failures for the seismic design in the Fraser Delta in British Columbia in view of the area`s proneness to liquefaction during a major earthquake. 31 refs., 5 tabs., 45 figs.

International Nuclear Information System (INIS)

This paper reviews generation methods of artificial earthquake motion and proposes an improved method of generating input motions for use in vibration tests of equipment to prove aseismic performance. The improved method employs beat wave repetition characteristic that inherently appears in the component waves of recorded earthquakes decomposed by bandpass filter and algebraic function phase for the component waves. Typical motions generated by the improved method satisfies prescribed severe conditions such as target response spectrum that are defined with a wideband frequency component and a limited maximum acceleration due to shaking table performance. The motions had never been generated by the conventional method.

Energy Technology Data Exchange (ETDEWEB)

This standard addresses the design bases for light water reactor, nuclear power plant structures and components essential for the protection of public health and safety from the potential adverse effects of pipe whip, jet impingement, pressurization of compartments outside containment, environmental conditions and flooding associated with a postulated pipe rupture. The design bases for missile protection and the design bases for containment pressurization are not within this standard.

Energy Technology Data Exchange (ETDEWEB)

In the development of the man-made island siting technology of nuclear power plants, assessing the stability of the seawall against large ocean waves and earthquakes is indispensable. Concerning with the seismic stability of the seawall, prediction of the deformation like sliding and settlement of the seawall during earthquake including the armour units in front of the caisson becomes important factor. For this purpose, the authors have developed the two-dimensional DEM-FEM coupled analysis method (SEAWALL-2D) to predict the deformation of the seawall covered with the armour units during earthquake. In this method, movements of the armour units are calculated in DEM analysis part and deformation of the caisson, rubble moundsand seabed and back fill are calculated in FEM analysis part taking the nonlinearity of the soil materials based on the effective stress into account. Numerical simulations of dynamic centrifuge model ...

Wastenet

... Austrian Environment Minister Nikolaus Berlakovich called for such stress tests on Sunday (13 March) to make sure that nuclear power stations were quake-proof following Japan's massive earthquake and tsunami. Austria, a mountainous country rich in geothermal energy, has no NPPs and no plans to develop ...

Science.gov (United States)

An understanding of the mechanism of generation of Lg from underground nuclear explosions is essential for seismic monitoring and source discrimination. Near-source scattering of explosion-generated Rg into S appears to be responsible for the low-frequenc...

International Nuclear Information System (INIS)

In an HTR plant high temperature components of Alloy 800 materials are subjected to temperatures from about 550 to 850degC in the long term; higher temperatures may occur in the short term. Thus the creep and stress-rupture parameters govern the design of these components. Since in recent years the scope of experimental data available for Alloy 800 materials has considerably increased, a new evaluation of the creep and creep-rupture properties was performed using a data bank computer. The relationships between the characteristics of the creep and creep-rupture behaviour and the metallurgical parameters were investigated by multilinear regression analyses. On the basis of the results of these analyses and after discussion in material expert committees new material specifications were determined for different types of Alloy 800. They were included into the draft standards DIN 17459 and DIN 17460 under the material standard ...

International Nuclear Information System (INIS)

The risk analysis was carried out in consideration of conditions prevailing at the Kalkar site analogous to the investigations in phase A of DRS (German Reactor Study). Earthquake design loads include the probabilities of upper deviations of the site intensities to be expected. The calculations of dynamic loads for select buildings are made using models and computational methods. Component analyses were performed analogous to DRS for the supports of large components, supports of the roof construction of the reactor building taking into account support reserves due to plastic work capacity, wall disks in steam generator buildings and switchboard plant buildings. (DG).

UK PubMed Central (United Kingdom)

We have developed and validated a microporous poly(ethylene terephthalate) membrane-based indirect co-culture system for human pluripotent stem cell (hPSC) propagation, which allows real-time...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

In the paper, the effect of Ni content, WC grain size and Mo2C addition on WC-6.25wt%TiC-9.3wt%Ni cemented carbide were investigated to improve the properties of Ni-bonded cemented carbides. The results show that the decrease of Ni content will result in the decrease of transverse rupture strength and increase of hardness; with the decrease of WC particle size, hardness increases due to the refinement of WC grains, however, the transverse rupture strength decrease due to the decrease of Ni binder thickness; Mo2C proves to be an effective grain growth inhibitor. With the increase of Mo2C content, the WC grains are refined and the hardness and transverse rupture strength are improved. Generally, when the Ni content is decreased to 8.4wt%, 13.45mm WC is used and 1.2wt% Mo2C is added, a higher...

Energy Technology Data Exchange (ETDEWEB)

The authors discuss the consistency (unitarity) of string propagation on the non-compact group SU(1,1) {times} G{sub c} and find the restriction on the level of the Kac-Moody algebra for this propagation to be unitary. They also suggest some modifications to the Virasoro generators and obtain a manifestly unitary string theory.

British Library Electronic Table of Contents (United Kingdom)

Flame propagating through zirconium particle cloud in a small-scale vertical rectangle chamber was investigated experimentally. In the experiments, the zirconium quoted 99% purity was used and the diameter of particles was distributed 1?22 ?m. The zirconium dust was dispersed into the chamber by air flow and ignited by an electrode spark. A high-speed video camera was used to record the images of the propagating flame. Micro-thermocouples, schlieren optical system and microscopic lens were used to obtain temperature profiles and flame structure, respectively. Based on the experimental results, flame propagation characteristics and flame structure of zirconium particle cloud were analyzed. The propagation velocity of the flame is quite slow in the initial 14 ms and then accelerates to maxim...

International Nuclear Information System (INIS)

Purpose: To assess the prevalence, significance and practical value of two recently described CT signs of instable aneurysm: the crescent sign and the periluminal halo (a low-attenuating internal layer of the thrombus around the patent lumen). Material and methods: Among the CT examination performed in the last 5 years, they retrospectively selected the nonruptured aneurysms with a diameter exceeding 4 cm (no. = 93 average diameter 5.1 cm, unenhanced images in 28 cases and enhanced in 84) and the ruptured aneurysms (no. = 16, average diameter 6.7 cm, unenhanced images in 9 cases and enhanced in 9). They studied the prevalence of the crescent and halo sing, their relationship with the aneurysm diameter, and the effect of contrast enhancement. Results: The crescent sign was identified with a statistically significant prevalence in ruptured ( 37.5 % or cases) over asymptomatic aneurysms (5.5 %); the halo had the same frequency in the 2 groups ...

UK PubMed Central (United Kingdom)

BackgroundAcute low back pain is a very common symptom and reason for many medical consultations. In some unusual circumstances it could be linked to a rare aetiology.Case...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Since several years, several manufacturers of circuit breakers from various countries (South Africa, UK, The Netherlands, USA..) try to impose in accommodations a highly sensitive electronic-type of differential circuit-breaker initially devoted to industrial installations where qualified and experienced professionals are present. This technical paper presents first the principles of the classical electromechanical circuit breakers and of the electronic circuit breaker, and then compares their relative efficiency and level of safety in residential use conditions (grounding schemes, voltage drops, rupture of the neutral conductor, rupture of the phase conductor, overvoltages). (J.S.)

International Nuclear Information System (INIS)

The post (neutron) -irradiation high-temperature tensile and creep-rupture properties, deformation and fracture characteristics of austenitic alloys, particularly solution annealed Type 316 steel, are surveyed and correlated with the damage structures developed as a function of irradiation temperature (and dose). The mechanisms proposed to explain the irradiation-induced changes in properties and behaviour are summarised. The factors responsible for the observed differences in the post-irradiation and 'in-reactor' creep-rupture properties and behaviour of an austenitic steel are discussed in terms of the helium gas and stress driven growth of small intergranular bubbles and the atom plating associated with their growth and coalescence. (author).

International Nuclear Information System (INIS)

The Chuetsu-oki Earthquake strongly shook the Kashiwazaki-Kariwa Nuclear Power Station with the ground motions exceeding the design values. The incidents include a fire breakout of the Unit 3 transformer, a release of spilled water containing small amount of radioactive materials to the non-radiation control area and subsequently to the environment at Unit 6, and a release of radioactive material from the main turbine condenser through the main stack of Unit 7 due to the delay stooping the turbine gland steam ventilator by the operator in manually, while every unit in operation was safety shutdown in the automatic mode ensuring the three fundamental safety functions of (a) reactivity control, (b) removal of heat from the core and (c) confinement of radioactive materials. Following integrity evaluation and performance testing of the overall plant, seismic safety of buildings, structures, equipment and pipelines on the basis of the basic ...

Science.gov (United States)

The Seismic Risk Explorer, an extension for ArcGIS Desktop developed by cedim AG, is a tool for computing the seismic risk, i.e. damage on residential buildings and thereby caused monetary losses for earthquake scenarios. It is based on the research results of the CEDIM (Center for Disaster Management and Risk Reduction Technology) research center, located at the Karlsruhe Institute of Technology (KIT) and the GeoForschungsZentrum (GFZ) in Potsdam. With this software tool seismic scenarios can be simulated for a given magnitude, depths and location. The seismic intensity, the resulting mean damage ratio for residential buildings and the seismic risk, expressed as the monetary loss caused by an earthquake can be computed downscaled to communities, postcode areas or even single buildings. Interested end-users are especially insurance companies, but also public authorities which may use the tool for risk management issues.

British Library Electronic Table of Contents (United Kingdom)

Some factors affecting the accuracy of magnitude calibration of palaeoearthquakes are discussed. The general problem is illustrated by two case studies. First, the 2003 strong earthquake in the Altai region (Russia-Mongolia border), which has generated co-seismic surface faulting is considered. An analysis is conducted to determine how accurately its magnitude could be defined after 2000 years based on surface faulting parameters, retrieved when future palaeoearthquake studies are launched. This example demonstrates that accurate evaluation of magnitude is possible if specific regional seismotectonic features are taken into account and surface faulting parameters are measured over a dense grid. Next, the Muya earthquake that occurred in the Baikal seismic region in 1957 is studied with res...

International Nuclear Information System (INIS)

At Cazzaso (Friuli) in northeast Italy, radon ("2"2"2Rn) activity concentration in soil gas in a borehole at a depth of 80 cm has been monitored continuously (at a frequency of once an hour) since May 2004, using a Barasol probe (Algade, France). In addition, environmental parameters (air and soil temperature, barometric pressure) have been recorded. The results have been evaluated and the relationship between radon levels and seismic activity is discussed. Correlation between radon concentration and barometric pressure has been observed. Preliminary results have shown a distinct radon anomaly prior to some earthquakes. (authors)

Science.gov (United States)

Effective-index approach is applied for modeling of channel plasmon polaritons (CPPs) propagating in rectangular grooves (trenches) and triangular (V-shaped) grooves in gold, accounting for the main features of CPP guiding and elucidating its underlying physics. The effective indexes of CPP modes along with the corresponding propagation lengths are calculated for different configurations and wavelengths while varying the groove depth. The results obtained allow one to identify the parameter range for realizing the single-mode CPP guiding featuring subwavelength confinement and moderate propagation loss at telecom wavelengths.

Energy Technology Data Exchange (ETDEWEB)

A considerable time can elapse between initial selection of candidate plus trees and harvest of improved seed. The technique showing the greatest promise of shortening this interval is vegetative propagation. Stock plants are grown for two years from seed before the first propagation cycle begins and each plant can be bulked-up 300-500 times over two cycles. An initial stock of 2500 superior Sitka Spruce plants can be multiplied to yield between 300,000 and 750,000 rooted cuttings for forest use within four years from the start of propagation.

Energy Technology Data Exchange (ETDEWEB)

Within the framework of efforts to optimize state-of-the-art waste disposal methods, this research project makes a theoretical analysis of the propagation behaviour of pollutants from landfills and waste incineration plants into the immediate vicinity of such plants. In order to judge the propagation of pollutants near the above-mentioned waste disposal facilities, a calculation program was developed within the framework of this research project which permits simulation of the propagation of such emissions in a three-dimensional space by application of an Eulerian grid model. It is capable of realistically representing fluid flow conditions and pollutant concentrations for certain points of times within the complex building patterns of such plants, for randomly chosen atmospheric conditions. (orig.)

CERN Document Server

We describe an analytic continuation of the Euclidean Grosse-Wulkenhaar and LSZ models which defines a one-parameter family of duality covariant noncommutative field theories interpolating between Euclidean and Minkowski space versions of these models, and provides an alternative regularization to the usual Feynman prescription. This regularization allows for a matrix model representation of the field theories in terms of a complex generalization of the usual basis of Landau wavefunctions. The corresponding propagators are calculated and identified with the Feynman propagators of the field theories. The regulated quantum field theories are shown to be UV/IR-duality covariant. We study the asymptotics of the regularized propagators in position and matrix space representations, and confirm that they generically possess a comparably good decay behaviour as in the Euclidean case.

Energy Technology Data Exchange (ETDEWEB)

The morphological evolution of ripples formed on the surface of Cd2Nb2O7 pyrochlore single crystals by focused ion beam (FIB) bombardment was investigated using in situ electron microscopy. At high ion fluences and off-normal bombardment angles, faceted surface ripples with a terrace-like structure were observed. The ripple propagation direction was oriented along the projected ion beam direction at incident angles ranging from 35 to 65 following high-dose ion bombardment. One side of the terrace was found to be perpendicular to the incident ion beam direction, while the other side was parallel to the ion beam. The terrace propagation velocity and direction were determined and interpreted on the basis of this asymmetric structure. A model based on the propagation of a shock wave that effectively self-selects a stable slope, was developed in order to explain the observed faceted ripple formation.

Science.gov (United States)

... these features and yields results which are two orders of magnitude faster than those available using conventional numerical ray tracing techniques ...

CERN Document Server

The nucleation and propagation of hydrofractures by injection of over pressured fluids in an elastic and isotropic medium are studied experimentally. Non-Newtonian fluids are injected inside a gelatine whose mechanical properties are assumed isotropic at the experimental strain rates. Linear elastic theory predicts that plastic deformation associated to breakage of gelatin bonds is limited to a small zone ahead of the tip of the propagating fracture and that propagation will be maintained while the fluid pressure exceeds the normal stress to the fracture walls (Ch\\'avez-\\'Alvarez,2008) (i.e., the minimum compressive stress), resulting in a single mode I fracture geometry. However, we observed the propagation of fractures type II and III as well as nucleation of secondary fractures, with oblique to perpendicular trajectories with respect to the initial fracture. In the Video ...

Science.gov (United States)

Inertial navigation error propagation. Hypersonic entry guidance techniques. Ablation effects on hypersonic aero-. Primary navigation and guidance ...

International Nuclear Information System (INIS)

Radon concentration measurement in the ground can be used for the prospecting for uranium and earthquake prediction. Some results of radon concentration measurement in the soil are presented here. The moisture condensation at the detector surface can affect on the detection efficiency. Due to this problem we tested a few filter papers on water permeability. The ratio of track densities on solid state nuclear track detector (SSNTD) in the open and the closed diffusion chamber is also determined. (author)

Energy Technology Data Exchange (ETDEWEB)

Recently the increase of steam temperature and pressure of power plant is required to enhance the thermal efficiency and reduce the CO{sub 2} emission. For the application to advanced USC (Ultra Super Critical) boiler with steam temperature around 700 C, the application of Ni-based alloy such as Alloy617 will be necessary. A new Ni-based alloy USC141 (20Cr-10Mo-2Ti-Al-bal.Ni) with excellent creep rupture strength and low thermal expansion has been developed by Hitachi Ltd. and Hitachi Metals Ltd. as the candidate material for 700 C USC turbine components. In present work, to investigate the possibility for boiler tube application of USC141, its weldability and high temperature strength properties were experimentally examined. The tested material as solution-treated condition shows higher creep rupture strength than that of Alloy617. GTAW (Gas Tungsten Arc Welding) trials of tubular specimen using NIMONIC263 filler wire were conducted ...

Energy Technology Data Exchange (ETDEWEB)

The Japan Atomic Energy Research Institute has conducted a piping reliability test program to demonstrate the safety and reliability of light water reactor primary piping. In this program, pipe fatigue test, leak-before-break (LBB) verification test and pipe rupture test were carried out to examine the integrity of piping, to verify the LBB and to demonstrate the effectiveness of protective measures against jet impingement and pipe whip loads under a pipe rupture event.In the pipe fatigue test, a procedure to predict the fatigue crack growth was developed, and the integrity of piping during the plant service life was evaluated. In the LBB verification test, the pipe fracture test and the leak rate test were performed to verify the LBB in the primary piping.In the pipe rupture test, the influence of jet impingement on the target disk and the deformation behavior of whipping pipe and restraint were investigated. Using the ...

Energy Technology Data Exchange (ETDEWEB)

Upon request by the Science and Technology Agency of Japanese Government, the Japan Atomic Energy Research Institute has conducted Piping Reliability Test Program to demonstrate the safety and reliability of light water reactor primary pipings. In this report, the results of the program are summarized. In the test program, pipe fatigue tests, Leak-Before-Break (LBB) verification tests and pipe rupture tests were carried out to examine the integrity of pipings, to verify the LBB concept and to demonstrate the effectiveness of the protective measures against jet impingement and pipe whip under pipe rupture event, respectively. In the pipe fatigue tests, a procedure to predict the fatigue crack growth was developed and the integrity of piping during plant service life was demonstrated. In the LBB verification tests, pipe fracture tests and leak rate tests were performed using cracked pipes. Based on the test results, LBB in the primary pipings was ...

Energy Technology Data Exchange (ETDEWEB)

Weldability and high temperature strength properties of Hastelloy Alloy XR were investigated in order to evaluate the materials performance of base metal and filler metal for the High Temperature Engineering Test Reactor (HTTR) uses. The weldability was examined by means of the chemical analysis in the deposited metals, optical microscopy, FISCO test, hardness measurements and bend test. The high temperature strength properties were investigated through tensile tests at R.T., 800, 900 and 950degC in air, and creep and creep rupture tests at 900 and 950degC in air. The results obtained by each test showed favorable performance. In particular, the bend test which is considered to be critical pass demonstrated low susceptibility to weld cracking through the optimization of B and C contents in the filler metal and by narrowing the groove. Creep rupture strength was nearly equal or higher than those of Hastelloy Alloy XR master curve and was much ...

Energy Technology Data Exchange (ETDEWEB)

Most of previous study for creep rupture of RPV lower head under severe accident condition, have been focused on global failure of RPV lower head. In contract, the local failure of the RPV nozzle region has not been studied in detail. The existence and features of nozzle failure in LAVA-ICI specimen of KAERI and LHF-4 specimen of Sandia National Lab., are observed. It is confirmed that the nozzle failure of LHF-4 specimen is due to the hoop stress in the RPV. The tensile tests in various temperatures and the creep rupture tests in various temperatures and stresses, are accomplished. The finite element analysis for LAVA-ICI experiment was confirmed, and the stress and deformation analysis results are used in LAVA-ICI experiment. 17 refs., 34 figs., 3 tabs. (Author)

British Library Electronic Table of Contents (United Kingdom)

North American design codes are now committed to the development of load and resistance factor design (LRFD) for reinforced soil structures including internal stability limit states. Reliability-based analysis is required to carry out these calibrations. A framework for LRFD calibration has been proposed by the writers that requires bias statistics for load and resistance terms for each limit state function. In this paper the formulation of the limit state for reinforcement tensile rupture is developed and the component strength-reduction bias statistics identified. The paper describes how to compute bias statistics from project-specific installation damage trials for use in reliability-based design for the reinforcement rupture limit state or using data from multiple sources for LRFD cali...

International Nuclear Information System (INIS)

The propagation of bradyon and tachyon wave functions can be compared by considering them as cases of normal and anomalous dispersion and using the ideas of Brillouin which where developed in order to describe the propagation of light in a transparent medium near an adsorption line. It is found that if a wave packet, or pulse, is formed using a superposition of waves moving only in the positive x direction, including both positive energies, it will propagate superluminally for both bradyons and tachyons. If non-physical states, imaginary moments and energies, are included in the superposition, both types of waves will propagate subluminally and remain within the light cone. This last result has also been obtained by Fox, Kuper and Lipson and Strnad and Kodre for tachyons when they included imaginary energies in their superposition. However, these approaches allow the tachyon to be localizable in space ...

Energy Technology Data Exchange (ETDEWEB)

A renormalization procedure is proposed which applies to lattice Feynman integrals containing zero-mass propagators and is analogous to the BPHZL renormalization procedure for continuum Feynman integrals. The renormalized diagrams are infrared convergent for non-exceptional external momenta, if the vertices of the theory satisfy a general infrared constraint. Under the same conditions as in the massive case, the continuum limit of the renormalized theory exists and is independent of the details of the lattice action.

Science.gov (United States)

Channel plasmon polaritons (CPPs) propagating along the bottom of subwavelength grooves cut into a metal surface were recently shown to exhibit strong confinement combined with low propagation loss, a feature that makes this guiding configuration very promising for the realisation of ultra-compact photonic components. Here, the results of our investigations of CPP guiding by V-grooves cut into gold are presented, demonstrating efficient large-angle bending and splitting of radiation as well as waveguide-ring resonators and Bragg grating filters.

Energy Technology Data Exchange (ETDEWEB)

The generating functional in which the residual gauge freedom has been broken is related to the conventional generating functional for QED in arbitrary dimension. Closed expressions which relate ordinary N-point Green functions to N-point Green functions in the different gauges are derived. The leading logarithmic behaviour of the electron propagator in three dimensions is thus obtained. It is argued that one should not ascribe much importance to the infrared behaviour of the fermion propagator in the context of confinement.

Energy Technology Data Exchange (ETDEWEB)

The available measurements on the cosmic-ray antiproton/proton ratio show an excess of antiprotons above predictions derived in the framework of the standard picture of cosmic-ray origin and propagation. Calculations are performed of the production from collisions of cosmic rays with the interstellar gas under the condition of distributed reacceleration. It could be shown that the calculated antiproton/proton ratio is enhanced compared to that derived from the leaky box model, but it remains difficult to bring it into agreement with the data by reasonable astrophysical assumptions. 15 references.

Energy Technology Data Exchange (ETDEWEB)

Propagation costs could be cut by replacing part of the micropropagation process with steps involving more traditional techniques. This study explored possibilities for improving existing vegetative propagation techniques for aspen using stem cuttings obtained from micropropagated plants. Vegetative propagation through stem cuttings was studied in 10 micropropagated hybrid aspen clones (Populus tremula L. x P. tremuloides Michx). Cuttings containing one axillary bud were harvested from the same donor plants twice during the growing season: the first harvest in May and the second harvest in July. Rooting percentage was correlated positively with root length, number of roots and height of cutting plant but negatively with length of rooting. The average rooting percentage was 53% in the first harvest and 27% in second harvest. Indole-3-butyric acid treatments (1.2 mM) significantly improved rooting in the second harvest, but ...

International Nuclear Information System (INIS)

Modeling free-electron laser (FEL) oscillators requires calculation of both the light-beam interaction within the undulator and the light propagation outside the undulator. We have developed a paraxial optical propagation code that can be combined with various existing models of gain media, for example, Genesis 1.3 for FELs, to model oscillators with full paraxial wave propagation within the resonator. A flexible scripting interface is used both to describe the optical resonator and to control the codes for propagation and amplification. To illustrate its capabilities, we numerically investigate two significantly different FEL oscillators: the free-electron laser for infrared experiments (FELIX) system and the vacuum-ultraviolet (VUV)-FEL oscillator of the proposed high-gain fourth generation light source. For the FELIX system, we find that diffraction losses are a considerable part of the single-pass ...

Energy Technology Data Exchange (ETDEWEB)

Crack arrest of fast running cracks is an important issue for the safety of steel structures. Crack arrest design can prevent fatal damage of large structures by restricting the influence of the incidents. Therefore crack arrest design is important especially for very large structure, where accidents may cause huge economical and social losses. Propagating shear fracture, long running ductile crack propagation in pipelines and brittle crack propagation in heavy thick shipbuilding steels have been investigated. For the propagating shear fracture issue, a new HLP simulation model, applicable to various backfill conditions, including underwater backfill, was developed. The proposed backfill model can be applied to the prediction of the crack arrest of propagating shear fracture under various backfill conditions. The new HLP simulation was successful in estimating full-scale burst tests ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: To assess the prevalence, significance and practical value of two recently described CT signs of instable aneurysm: the crescent sign and the periluminal halo (a low-attenuating internal layer of the thrombus around the patent lumen). Material and methods: Among the CT examination performed in the last 5 years, they retrospectively selected the nonruptured aneurysms with a diameter exceeding 4 cm (no. = 93 average diameter 5.1 cm, unenhanced images in 28 cases and enhanced in 84) and the ruptured aneurysms (no. = 16, average diameter 6.7 cm, unenhanced images in 9 cases and enhanced in 9). They studied the prevalence of the crescent and halo sing, their relationship with the aneurysm diameter, and the effect of contrast enhancement. Results: The crescent sign was identified with a statistically significant prevalence in ruptured ( 37.5 % or cases) over asymptomatic aneurysms (5.5 %); the halo had the same frequency in the 2 groups ...

Energy Technology Data Exchange (ETDEWEB)

HANARO fuel test loop will be equipped in HANARO to obtain the development betterment of advanced fuel and materials through the irradiation test. The object of this study is to evaluate the structural integrity of FTL in-pool piping by investigating a dynamic analysis of the loop containing a postulated rupture section. The method to perform the dynamic analysis and structural integrity evaluation caused by the pipe whip in water environment can be a reference for a similar structural integrity evaluation. (author). 7 refs., 39 tabs., 34 figs.

Energy Technology Data Exchange (ETDEWEB)

There is need of pressure surge analyses when valves or pumps are activated or piping systems fail (pipe rupture). Based on actual problems the influences of boundary conditions upon fluid simulation results are discussed. Hints concerning realistic dynamic analyses of piping systems are presented. Some of the simulations results are compared with measurements. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Microfluidic systems and methods are disclosed which are adapted to transport and lyse cellular components of a test sample for analysis. The disclosed microfluidic systems and methods, which employ an electric field to rupture the cell membrane, cause unusually rapid lysis, thereby minimizing continued cellular activity and resulting in greater accuracy of analysis of cell processes.

Energy Technology Data Exchange (ETDEWEB)

Angiography plays a vital role in the investigation of the patient suffering from multiple trauma. The commonest injuries have been rupture of the thoracic aorta, renal lacerations, arterial bleeding associated with fractures and soft-tissue injuries to the pelvis, and occlusions of the arteries supplying the limbs. Transcatheter arterial embolization may be the definitive therapeutic procedure in pelvic bleeding.

International Nuclear Information System (INIS)

Fuel assemblies in a reactor pressure vessel are disposed in a reactor core shroud. The own weight of the fuel assembly is supported by a reactor core support plate, and is supported, for the horizontal direction, by an upper lattice plate and the reactor core support plate. A support portion for the upper portion of the fuel assembly is disposed above the fuel assembly, and a support portion for the support portion described above is joined to a shroud head by welding. The support portion for the upper portion of the fuel assembly has a network-like portion which absorbs and disperses rising force which exerted on the fuel assembly when the fuel assembly is risen by seismic forces. The rising force exerted on the fuel assembly absorbed by the network-like portion is effectively transferred to the shroud head by the support portion. With such a constitution, rising of the fuel assembly can be prevented against the seismic vibrations having prominent vertical vibration components such ...

CERN Document Server

Heating during frictional sliding is a major component of the energy budget of earthquakes and represents a potential weakening mechanism. It is therefore important to investigate how heat dissipates during sliding on simulated faults. We present results from laboratory friction experiments where a halite (NaCl) slider held under constant load is dragged across a coarse substrate. Surface evolution and frictional resistance are recorded. Heat emission at the sliding surface is monitored using an infra-red camera. We demonstrate a link between plastic deformations of halite and enhanced heating characterized by transient localized heat spots. When sand 'gouge' is added to the interface, heating is more diffuse. Importantly, when strong asperities concentrate deformation, significantly more heat is produced locally. In natural faults such regions could be nucleation patches for melt production and hence potentially initiate weakening during ...

International Nuclear Information System (INIS)

Nowadays the safety of Nuclear Power Plants is becoming more and more significant. Therefore consideration of severe accidents shall be included in both design and operating process of Nuclear Power Plants. In particular ground motion forms one of the important natural hazards. For structural analysis both linear-elastic and non-linear methods are specified by the engineering codes for earthquake resistance design. However, time history analysis is required for investigation of non-linear structural behaviour. Moreover, non-linearities are often caused by the presence of damage. This can be detected by means of structural health monitoring and subsequently system identification. In this paper the advantages of both dynamic time history analysis and damage detection by means of wavelet analysis are discussed. First, the non-linear behaviour of a frame structure due to an artificial earthquake motion is analyzed. A comparison to non-time history ...

Energy Technology Data Exchange (ETDEWEB)

A 200 ft. tall stack, consisting of a concrete chimney with an independent acid proof brick liner built in the 1950`s, serving the Separations facility at the Savannah River Site (SRS), was evaluated for the performance category 3 (PC3) level of Natural Phenomena Hazards (NPH) effects. The inelastic energy absorption capacity of the concrete chimney was considered in the evaluation of the earthquake resistance, in particular, to compute the F{sub {mu}} factor. The calculated value of F{sub {mu}} exceeded 3.0, while the seismic demand for the PC3 level, using an F{sub {mu}} value of 1.5, was found to be less than the capacity of the concrete chimney. The capacity formulation of ACI 307 was modified to incorporate the effect of an after design opening on the tension side. There are considerable uncertainties in determining the earthquake resistance of the independent brick liner. The critical liner section, located at the bottom of the breeching ...

Energy Technology Data Exchange (ETDEWEB)

Experimental investigations were performed to assess the effects of different shaped obstructions on flame propagation in a rectangular confinement, 235 mm in height, with a 1000 x 950mm cross section and a large top-venting area of 1000 x 320mm. Four different single obstacles were used: rectangular, cylindrical, triangular, and square cross-sections with blockage ratios of 5 and 10%. Temporally resolved flame front images were recorded by a high-speed video camera to investigate the interaction between a propagating flame and the obstacle. The local flame displacement speeds and their probability density functions (pdfs) were obtained for the different obstacles. Before the freely propagating flame impinges on the obstacle, the flame propagation speed remains close to the laminar burning velocity, regardless of the obstacles used. As the propagating flame impinges on the obstacle, ...

Energy Technology Data Exchange (ETDEWEB)

The various technical aspects of radon concentration measurements in the ground or in the groundwater are reviewed. The emphasis is put on the most convenient techniques particularly suited for in situ monitoring in the field. Some attention is paid to the thoron problem. Historical and most recent findings in the field or earthquake related radon anomalies are presented and briefly discussed. A similar approach is made to rarer volcanic cases that have been documented up to now. A short discussion regarding the various models that intend to provide satisfactory explanations is presented, supported, whenever it is possible, by experimental laboratory results. Finally a glimpse on the possible and future application of the method to hydrogeology is given. (orig.).

Energy Technology Data Exchange (ETDEWEB)

It is important to accurately estimate the effects of strong earthquake motions on the basemat uplift behavior and structural responses for the seismic design of nuclear power plant buildings. In this paper, an analysis model which describes the soil part using the 3 dimensional FEM was proposed to be used when the ground contact ratio is low, and the validity of this model was confirmed. Furthermore, investigations using the model were carried out where the attaching force under the basemat was taken into account, in order to more realistically estimate the basemat uplift behavior. The effects in the case of the building being embedded were also investigated.

Science.gov (United States)

A nonlinear partial differential equation modeling the propagation of a vertical hydraulic fracture first derived by Nordgren is studied. When properly posed, Nordgren's derivation constitutes a Stefan problem and requires another boundary condition-namely, that the velocity of the fluid at the crack tip equals the velocity of crack propagation. With this addition, Nordgren's similarity solution in the no-leakoff case is perfected by a power-series solution. New shut-in solutions are derived in the large-and-no-leakoff cases where the crack of the large-leakoff shut-in solution retracts and the crack of the no-leakoff shut-in solution extends forever. This study ignores the effect of crack-tip rock strength on crack propagation.

Energy Technology Data Exchange (ETDEWEB)

An effect of load conditions on Corrosion Fatigue Crack Propagation (CFCP) behavior of High Performance Steel (HPS) under seawater environment was investigated. Fatigue crack propagation tests under several load conditions including stress ratio and load frequency were conducted in air and 3.5% NaCl solution environments. Corrosion/fatigue ratio factor, C/F, particularly was defined to analyze the effect of such conditions. As shown in the results, a decrease of load ratio and frequency leads to an increase of C/F factor. Consequently, under lower loading frequency and stress ratio, the seawater condition causes much more significant effect on CFCP behavior of HPS.

International Nuclear Information System (INIS)

Up to 90% of the life time of cyclically loaded components is determined by short crack initiation and propagation. This stage of the fatigue damage process is strongly influenced by microstructural features, e.g. grain boundaries and crystallographic grain orientation. Therefore LEFM can not be applied in a reasonable manner explaining the demand for a mechanism-related modelling method. The present study deals with mechanical testing and microstructural examinations applied to the relatively new #beta#-titanium alloy LCB. The results are used as data base to develop a new short crack model that is based on the model of Navarro and de los Rios. By using various techniques such as electron back-scattered diffraction and finite-element calculations the origin of crack initiation is revealed and the characteristics of crack propagation is determined. (orig.)

International Nuclear Information System (INIS)

The effect of Kerr nonlinearity on an Airy beam is investigated by using the nonlinear Schroedinger equation. Based on the moments method, the evolution of the Airy beam width in the rms sense is analytically described. Numerical simulations indicate that the central parts of the major lobe of the Airy beam initially give rise to radial compression during propagation in a focusing medium, even though the rms beam width broadens. The partial collapse of the center parts of the major lobe of the beam appear below the threshold for a global collapse. The evolutions of the field distributions of the Airy beams are different during propagation in different Kerr media while the beams still travel along the parabolic trajectory just as the beam propagates in free space.

Energy Technology Data Exchange (ETDEWEB)

The end of 1994, five seismic observation stations were constructed with digital seismograph and 3-component seismometers. In this study, the epicentral distribution around the Kyungsang basin was obtained from one-year earthquake data (1994/12 - 1995/11) and compared with the annual earthquake report of KMA (Korea Meteorological Agency). The geological structure at the middle of the Ulsan fault was also investigated by the electrical resistivity method. The epicenters show high concentration at the Wolsung area. They show a linear alignment and their depths tend to be deeper as they approach to the coast line of the East Sea. These imply that they are probably correlated together. Another remarkable feature on land is the linear epicentral distribution along Jiri mountain to the Kimcheon and Sangju. This line is well coincident with newly recognized lineament. The other is the epicentral distribution at the Straits of Korea and East Sea. Even ...

International Nuclear Information System (INIS)

The dynamic response of thin liquid storage tanks to earthquakes is a very complicated phenomenon, because it can be highly non linear. Among others, one can meet material and geometric non linearities of the tank shell leading eventually to static or dynamic buckling non linear behavior of anchor bolts, contact non-linearities due to the uplift of the tank base and to the unilateral character of the fluid pressure on the shell and high amplitude fluid oscillations. Moreover, linear or non linear soil structure interaction affects considerably the response of the fluid structure system under consideration. In this paper we focus attention on problems related only to the base uplift and anchors plastification. We study a tank similar to the Hualien project tank, but we neglect the soil structure interaction. The studied tank is representative of medium height to radius ratio ratio tanks with relatively thick bottom plate. The contact is simulated via a simple ...

CERN Document Server

Observations show the ubiquitous presence of propagating magnetohydrodynamic (MHD) kink waves in the solar atmosphere. Waves and flows are often observed simultaneously. Due to plasma inhomogeneity in the perpendicular direction to the magnetic field, kink waves are spatially damped by resonant absorption. The presence of flow may affect the wave spatial damping. Here, we investigate the effect of longitudinal background flow on the propagation and spatial damping of resonant kink waves in transversely nonuniform magnetic flux tubes. We combine approximate analytical theory with numerical investigation. The analytical theory uses the thin tube (TT) and thin boundary (TB) approximations to obtain expressions for the wavelength and the damping length. Numerically, we verify the previously obtained analytical expressions by means of the full solution of the resistive MHD eigenvalue problem beyond the TT and TB approximations. We find that the ...

Science.gov (United States)

time as well, due to the complex patterns of air movement taking place within cumulus clouds. ...... cumulative distribution of XPD, for rain and ice-particle induced ...... CCIR (1986f), Attenuation by Hydrometeors, In Particular ...

UK PubMed Central (United Kingdom)

PurposeAuto-propagation of anatomical region-of-interests (ROIs) from the planning CT to daily CT is an essential step in image-guided adaptive radiotherapy. The...Full Text Available

Science.gov (United States)

Characteristics of inertia gravity waves associated with convection are investigated in the lower stratosphere using high-resolution radiosonde data observed from 18 June to 15 July of 2005 and 2007 in Korea. Three-dimensional ray-tracing model and reanalysis data are used to investigate the propagation and the sources of the observed waves. The observed waves associated with convections are discriminated based on the existence of convections when and where the rays reach the average height range of convective clouds. Waves observed in 2005 and 2007 show similar spectral characteristics, but wave energy in 2007 is significantly larger than in 2005. The observed waves propagate from three source regions: the northeastern, southeastern, and western regions around Korea. They show preferential propagation directions based on their sources, and convections from the western region generate larger-amplitude gravity waves than the ...

UK PubMed Central (United Kingdom)

Thermodynamic parameters for prediction of RNA duplex stability are reported. One parameter for duplex initiation and 10 parameters for helix propagation are derived from enthalpy and free-energy changes...Full Text Available

UK PubMed Central (United Kingdom)

Each heartbeat requires precisely orchestrated action potential propagation through the myocardium achieved by coordination of about a million ion channels on the surface of each cardiomyocyte....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Forest research on fast growing Eucalyptus hybrids in the Congo, using coppice shoots for propagation, is described. The hybrids can grow 20 ft in 15 months and it is suggested that the application of such methods in Britain may increase the growth rates of hardwoods such as oak or walnut.

UK PubMed Central (United Kingdom)

B lymphocytes can function independently as efficient APCs. However, our previous studies demonstrate that both dendritic cells and macrophages are necessary to propagate immune responses initiated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Potential uses of foliage and bark wastes of E. ('Mysore') hybrid in southern India for the production of cineole and oxalic acid respectively are discussed. Only certain strains are cineole-rich and these are being successfully propagated vegetatively at the authors' laboratory.

Science.gov (United States)

Inertial navigation error propagation. 153. 100. --. 8. GN-5. Hypersonic entry guidance techniques. 150. 100. 0.8. 9. FM-13. Ablation effects on hypersonic ...

International Nuclear Information System (INIS)

The wave equation for spin;1/2 tachyons is derived from the Dirac equation and the principle of relativity extended to superluminal Lorentz frames. From this wave equation and the Dirac equation infinite velocity spinor transformations are obtained. They yield bispinors of the plane-wave states of the tachyon, their interpretation and covariant orthogonality relations satisfied by them. The transformation properties of the bispinors under Lorentz transformation are discussed. The boundary conditions for the free propagator of wave functions of tachyons are obtained and the propagator is constructed. Then the covariant S-matrix for scattering from an electromagnetic field is derived. It is applied to the scattering of electron-tachyons from the Coulomb field.

Energy Technology Data Exchange (ETDEWEB)

We consider propagation of relativistic heavy nuclei injected by a young pulsar into the radiation field of a massive companion. If the binary system (BS) is compact enough, then the nuclei suffer multiple photodisintegrations in collisions with thermal photons coming from the massive star (MS). Due to the propagation effects of charged particles in the magnetic field of the MS some hadrons can impinge onto the MS surface at large angles. We calculate the fluxes of produced neutrinos as a function of the viewing angle measured from the plane of the BS. It is found that significant fluxes of neutrinos should be also expected in the case of non-eclipsing BSs.

International Nuclear Information System (INIS)

In terms of the kinetic theory of the interaction between the high-power short-time laser pulses with plasma based on the propagator plotting for the plasma particle distribution functions one studied the generation of the hot electrons and of the fast ions as the relativistic femtosecond laser pulses travelled through the supercritical density plasma. One performed calculations based on the various values of the laser pulse intensity, types of the multiple-charged ions, the plasma inhomogeneity degree. One studied the acceleration mechanisms both of the plasma electrons and ions

Energy Technology Data Exchange (ETDEWEB)

The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of PTFE transfer film ...

International Nuclear Information System (INIS)

The photon rupture method, by which oxide film and metal are removed by focused pulsed Nd-YAG laser beam irradiation, was applied to form artificial micro-pits in Zn-5 mass% Al alloy-coated steel. The zinc alloy-coated layer was removed by pulsed laser irradiation treatment for about one second in a neutral buffer solution with NaCl. The rest potential transient with the laser treatment was measured. In the early stage of the laser treatment the rest potential of zinc alloy-coated steel changed to the negative direction immediately after every irradiation of a laser pulse and then returned to the previous value. However, after the steel substrate was exposed to the solution, the rest potential moved to the positive direction immediately after every irradiation of a laser pulse and then returned to the previous value. The amplitude and duration of the potential change after the laser irradiation increased with repetition of laser irradiation, related to the pit ...

International Nuclear Information System (INIS)

The weldability and high temperature strength properties of tungsten-inert-gas (TIG) weldments of Hastelloy alloy XR were investigated by using two different heats of filler metals; the first (HXRF1) was designed on the basis of multiple regression analysis; the second (HXRF2) was the reference material. Bend tests, the FISCO cracking test and optical metallography were used to evaluate weldability. Tensile and creep tests were performed at 900deg C to evaluate high temperature strength properties. The results of weldability tests for both alloys showed good performance. The tensile properties of the weldments were remarkably improved in particular with respect to high temperature ductility. The creep rupture strength in the weldments made with alloy-designed HXRF1 was much higher than those of the Hastelloy alloy XR-II base metal with a higher B content. Furthermore, the creep properties were stable with respect to variations in welding conditions. Since the ...

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of analysis of selected data from the NRU test series dealing with heatup and reflood heat transfer during postulated PWR LOCA conditions. These tests used nuclear fuel rods and some considered clad ballooning and rupture. Also included was an electrically-heated rod ballooning test, REBEKA-6. The COBRA-TF computer program, renamed PYTHONS, was modified and used for the analytical tool. Modifications included provisions for fuel rod gas flow and pressure, creep deformation and rupture, channel blockage, and blockage heat transfer. Calculated clad temperatures for NRU unpressurized rods show quite good agreement with experimental data. The calculated amount and axial extent of clad ballooning for pressurized rods agrees reasonably well with post-test examinations of the NRU bundles. Time to failure was underpredicted in the MT-3 test as a result of the high strength of NRU clad material which was not represented ...

Energy Technology Data Exchange (ETDEWEB)

Design methods and parameters are described which are addressed when considering consequences of a postulated pipe rupture event in a nuclear plant design. Parameters discussed are break opening time and size, resultant blowdown characteristics of the effluent from the broken pipe, jet reaction and impingement loading, pipe motion, and pipe impact loading on steel and concrete structures. The impact the various parameters have on overall plant designs and conservatisms inherent in each consideration are evaluated in a qualitative nature. Finally, recommendations are provided for each parameter discussed for further evaluation and study.

Energy Technology Data Exchange (ETDEWEB)

This paper presents a numerical simulation with the EUROPLEXUS fast dynamics software of a pipe whipping phenomenon occurring in the thermal hydraulic conditions of a loss of coolant accident in a PWR primary circuit. Different physical phenomena take place simultaneously during the rupture and the whipping of the pipe such as plasticity, contact, large displacements, two-phase flow regime and fluid structure interaction. Two kinds of numerical models - a simplified pipeline model and a mixed 1D/3D model - are considered and compared throughout modelling and computation. Numerical results are compared with experimental data belonging to the Aquitaine II test campaign.

International Nuclear Information System (INIS)

Spectra of e.p.r. radicals in cellulose and timber gamma-irradiated at 77 and 300 K have been measured. Radiation yields and the kinetics of radicals accumulation have been studied. The effect of ionizing radiation on cellulose is the appearance of radicals resulting from rupture of C-H bonds in positions 1 and 4. Timber, additionally, forms ''lignin'' radicals. A mechanism of cellulose and timber radiolysis is suggested. ''Lignin''-type compounds present in timber protect polysaccharides from radiation-induced destruction.

Energy Technology Data Exchange (ETDEWEB)

A back-up system is provided for a pumping plant or a pressure reservoir system used to maintain insulating oil under pressure in high voltage submarine power cables which includes a gas driven membrane pump to insure a small outflow of oil at a rupture point in the power cable to prevent water from penetrating the cable. The proper operation of the membrane pump is insured by introducing degasified oil at the drive side of the pump during the stand-by and test modes of operation of the back-up system. 11 drawings.

British Library Electronic Table of Contents (United Kingdom)

This paper seeks to investigate the liquefaction of clayey soils, a phenomenon that has been the trigger for many natural disasters in the last few decades, including landslides. Research was conducted on artificial clay?sand mixtures and natural clayey soils collected from the sliding surfaces of earthquake-induced landslides. The undrained response of normally consolidated clayey soils to cyclic loading was studied by means of a ring-shear apparatus. For the artificial clay?sand mixtures, it was found that the presence of a small amount of bentonite (?7%) would cause rapid liquefaction, while a further increase in bentonite content (?11%) produced the opposite effect of raising soil resistance to liquefaction by a significant degree. It was demonstrated that the bentonite?sand mixture wa...

Energy Technology Data Exchange (ETDEWEB)

Very large sparse linear least-squares problems arise in a variety of applications, such as geodetic network adjustments, photogrammetry, earthquake studies, and certain types of finite element analysis. Many of these problems are so large that it is impossible to solve them without using auxiliary storage devices. Some problems are so massive that the storage needed for their solution exceeds the virtual address space of the largest machines. A method for solving such problems on a typical (large) computer is described, and the results of some experiments illustrating the effectiveness of this approach are provided. The method includes an automatic partitioning scheme that is essential to the efficient management of the data on auxiliary files. 8 figures, 2 tables

Energy Technology Data Exchange (ETDEWEB)

This paper introduces the method of seismic stability analysis for the increase of fuel storage capacity of wet storage stacks by one or two more stack floor at Wolsung Nuclear Unit 2,3,4, which had been originally licensed assuming 16 tray stack-o-storage. As a basic procedure, tipping and sliding stability of the structure is checked at first thru seismic analysis and the resultant load from dynamic analysis is applied for static stress analysis, and the result of which is reviewed for compatability with applicable standard. As a result, sliding and overturning are not expected under design basis earthquakes for increased storage cases of 17 tray and 18 tray stacks. And it is anticipated the result of stress analysis will be acceptable.

Energy Technology Data Exchange (ETDEWEB)

BC Hydro has been assessing and upgrading its facilities and implementing response alternatives to potential damage resulting from a major earthquake. This paper reviews the utility`s seismic evaluation of its overhead transmission system, focusing on the Lower Mainland area where most of the tall critical river-crossing towers are located. The paper gives an overview of the geologic environment of the Lower Mainland and outlines the criteria used for assessing existing structures for their ability to withstand design seismic loads. It then describes the investigation and analysis methods used in the assessment, including geotechnical field tests, ground response analysis, determination of soil liquefaction potential, and dynamic analysis of structures and piles. Options for seismic upgrades are discussed and illustrated by the case of the Pitt River crossing, where tower foundations were reinforced with steel pipe piles.

International Nuclear Information System (INIS)

In the past decade, considerable progress has been made on reducing the seismic response of structures through seismic isolation. Application of seismic-isolation techniques to nuclear power facilities is currently being investigated. This paper presents an analysis of the effect of long period motions on a seismic-isolated nuclear structure. Preliminary analysis indicates that long-period earthquake motions increase structural accelerations and relative displacements between the upper and lower mats. Relative displacement between the mats can be represented by spectral displacement at the frequency of the structure, and can be effectively reduced by increasing viscous damping in the isolator. The isolated structure behaves as a system with one degree of freedom. Future analysis of seismic effects on seismic-isolated structures should include the linear and nonlinear effects of soil-structure interactions. 3 refs., 12 figs., 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

Earth degassing specifically of carbon dioxide CO2 is of increasing interest with respect to the global carbon budget, related climate effects, earthquake and volcano eruption mechanisms, as well as plant physiological reactions in gas-rich environments. Investigations in all of these disciplines require the detection of surface CO2 degassing structures and quantification of their emissions. We introduce minimal thermal change detection based on infrared imaging as a new remote sensing tool for the detection of earth surface thermal anomalies suiting among others to discover earth degassing locations of any origin. The method allows for seamless areal search and monitoring of degassing structures in any terrain. As proof of concept infrared imaging measurements were performed at the Bossol...

International Nuclear Information System (INIS)

A review of tests on earthquake-resistant reinforced concrete structural walls is presented. Laboratory tests of isolated walls and construction joints are discussed. Where appropriate, design recommendations are given. The review indicates only few experimental data are available for short walls which are directly applicable to nuclear power plant design. In particular, tests of short rectangular walls subjected to load reversals are needed. Tests are also needed to determine the damping and frequency characteristics of cracked short walls. Analytical and experimental results should be correlated so that the hysteretic response observed in tests can be realistically related to the analytical response 'demand' of nuclear power plant structures. (Auth.).

Science.gov (United States)

Observations are presented that link extratropical Rossby wave disturbances excited in the Southern Hemisphere subtropical jet to the initiation of convectively coupled Kelvin waves in the Pacific intertropical convergence zone (ITCZ) during austral winter. A baroclinic, zonal wavenumber 6, eastward-propagating Rossby wave train in the subtropical jet turns northeastward in the vicinity of Australia, inducing upper tropospheric divergence and vertical motion fields that spread equatorward and induce cloudiness anomalies in the Tropics. Lower tropospheric pressure surges excited from the extratropics also induce Kelvin wave-like geopotential height and temperature anomalies at the surface, providing additional lower tropospheric convergence and vertical motion forcing. The tropical outgoing longwave radiation (OLR) and circulation fields propagate eastward in tandem with the extratropical Rossby wave train at approximately 17 m s-1. Kelvin wave ...

Energy Technology Data Exchange (ETDEWEB)

The results presented here demonstrate that the Paul Trap Simulator Experiment (PTSX) simulates the propagation of intense charged particle beams over distances of many kilometers through magnetic alternating-gradient (AG) transport systems by making use of the similarity between the transverse dynamics of particles in the two systems. Plasmas have been trapped that correspond to normalized intensity parameters s = wp2 (0)/2wq2 * 0.8, where wp(r) is the plasmas frequency and wq is the average transverse focusing frequency in the smooth-focusing approximation. The measured root-mean-squared (RMS) radius of the beam is consistent with a model, equally applicable to both PTSX and AG systems that balances the average inward confining force against the outward pressure-gradient and space-charge forces. The PTSX device confines one-component cesium ion plasmas for hundreds of milliseconds, which is equivalent to over 10 km of beam propagation.

British Library Electronic Table of Contents (United Kingdom)

Abstract Polymorphisms in the genomic DNA of eight varieties maintained by conventional bud propagation (via rhizomes) and by in vitro shoot tip cultures were detected by RAPD analysis of sugarcane varieties. The study estimated the genetic diversity induced after in vitro multiplication of these varieties. Higher (28.9%) and lower (12%) numbers of polymorphic bands were detected in plants propagated via rhizomes; the genetic similarity estimate varying from 0.63 to 0.80. Plants of SP90-3723 and SP91-1049, or RB85-5113 and SP90-3723, varieties involving greater genetic distances may be indicated as progenitors in breeding programmes. In vitro multiplication of RB86-7515, RB85-5113, RB83-5054 and SP86-42 varieties increases genetic variability, while in vitro multiplication of SP91-1049, SP...

Energy Technology Data Exchange (ETDEWEB)

A study was conducted to predict indoor ventilation, smoke movement and fire propagation in a new building currently under construction at the Ecole Polytechnique de Montreal. It was conducted in response to concerns regarding the impact that air quality, in normal operation conditions, and smoke concentration, in the event of a fire, may have on occupants of a building. A detailed three-dimensional model of the new building was constructed using the NURBS-based modeler, Rhino. Simulations of fire propagation and airflow ventilation were performed in different areas of the building. The flow pattern data was analyzed using the computational fluid dynamics (CFD) program called FLUENT. It predicted air flow conditions and estimated the mean age of air (MAA) in the room. Real-world geometries, such as diffuser inlets, have a significant impact on overall fluid flow behaviour and are necessary for this type of analysis. The fire simulation was ...

International Nuclear Information System (INIS)

It is known that a high-power laser propagating through an underdense plasma can acquire a minimum spot size due to relativistic self-focusing. Beyond the focus, the nonlinear refraction starts weakening, and the spot size of the laser increases, showing periodic self-focusing/ defocusing behavior with the distance of propagation. To overcome the defocusing, we propose the introduction of a localized upward plasma density ramp. In the presence of an upward ramp of plasma density, the laser beam obtains a minimum spot size and maintains it with only a mild ripple. For suitable parameters of the laser and the plasma, we have deduced conditions for the self-focusing. This kind of plasma density ramp may be observed in a gas-jet plasma experiment and resembles a plasma lens.

International Nuclear Information System (INIS)

Gravitational waves are propagating fluctuations of gravitational fields, that is, '' ripples '' in space-time, generated mainly by moving massive bodies. These distortions of space-time travel with the speed of light. Every body in the path of such a wave feels a tidal gravitational force that acts perpendicular to the wave's direction of propagation; these forces change the distance between points, and the size of the changes is proportional to the distance between these points thus gravitational waves can be detected by devices which measure the induced length changes. The frequencies and the amplitudes of the waves are related to the motion of the masses involved. Thus, the analysis of gravitational waveforms allows us to learn about their source and, if there are more than two detectors involved in observation, to estimate the distance and position of their source on the sky. (author)

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this study was to evaluate the potential environmental effects (both adverse and beneficials) of aquifer thermal energy storage (ATES) technology pertaining to microbial communities indigenous to subsurface environments (i.e., aquifers) and the propagation, movement, and potential release of pathogenic microorganisms (specifically, Legionella) within ATES systems. Seasonal storage of thermal energy in aquifers shows great promise to reduce peak demand; reduce electric utility load problems; contribute to establishing favorable economics for district heating and cooling systems; and reduce pollution from extraction, refining, and combustion of fossil fuels. However, concerns that the widespread implementation of this technology may have adverse effects on biological systems indigeneous to aquifers, as well as help to propagate and release pathogenic organisms that enter thee environments need to be resolved. 101 refs., 2 ...

Energy Technology Data Exchange (ETDEWEB)

Poplar breeding in Europe is in a more advanced state than breeding programmes of other species. In Europe, poplars are part of the scenery and are integrated in the economy. Traditionally poplar stands are established in lowland areas. But an increasing interest in their use moved them to upland sites. Poplar uses are multiple: lumber, industrial wood, wind-breaks and landscape plantations, etc. Selection characteristics are classified in different groups: vegetative propagation ability, vigor, adaptation to sites and climate, resistance to diseases and insect pests, wood quality, and coppicing ability. Strategies have improved with time. The most efficient strategies for the long term involve constitution of base populations, selection of parents for intra- and interspecific hybridizations, selection within the progenies, and vegetative propagation. Short term strategies are also applied simultaneously. Advanced breeding techniques with ...

International Nuclear Information System (INIS)

The International Atomic Energy Agency has initiated a co-ordinated research programme on implementation of base-isolation for nuclear structures. This paper discusses two areas relevant to modelling elastomeric base-isolators. These are the use of simplified models to predict the response of isolated structures to earthquake inputs and finite element analysis for calculating the stress distributions within the isolators. In the former, a curvilinear hysteretic model of the high damping natural rubber able to accommodate the stiffening of the rubber at large shear deflections is presented. Its predictions of structural accelerations and bearing displacement produced by design earthquakes and those above the design level are compared with those using a linear spring and dashpot model. A comparison has been made between two finite element analyses using MARC and ABAQUS of the force-deformation behaviour of a single disc of rubber bonded on both ...

Energy Technology Data Exchange (ETDEWEB)

Several recent improved methods for the EGFM are introduced in order to avoid artificial holes seen in the synthetic acceleration spectrum. Furthermore evaluation of input ground motions at Wolsung NPP are performed by varying the source parameters that may control the high-frequency wave radiation and the deviation of the synthetic motions are revealed. The PSHA case studies for four NPP sites (Wolsung, Kori, Uljin, Younggwang) are performed. In the analysis, site-specific attenuation equations developed for Korean NPP sites are employed, and the seismic hazards for the target sites are evaluated in the case where the four kind of seismic source models are considered. Moreover, the PSHA for Wolsung and Younggwang are conducted by using the site-specific attenuation equation with the index of response spectra and the uniform hazard spectra are evaluated for the two sites. The supporting tool for seismic response analysis and the evaluation tool for evaluating annual probability of ...

International Nuclear Information System (INIS)

The effect of W and V on the high temperature strength properties of 12%Cr-15%Mn austenitic steels was studied from the view point of precipitation hardening and internal stress. The contribution of W addition to the tensile and creep-rupture strength was not so large. By contrast the combined addition of W and V increased the strength considerably. These are resulted from the precipitation of fine vanadium nitride (VN) within grains and the enhancement of M_2_3C_6 type carbide precipitation at grain boundaries. The V added material had large internal stress value which is considered to be due to dislocation movement disturbed by fine vanadium nitrides. (author).

Energy Technology Data Exchange (ETDEWEB)

By tests about pipe failure under extreme bending, moment at cross sections affected by circumferential cracks, admissible strains for securing the integrity in the area of a flow link are indicated. These are 7% for austenic and ferritic materials in the undisturbed cross section. From d/t-ratios of 20 onwards the strains are limited by pipe bulging on the pressure-load side. In this connection, circumferential flaws do not have any influence on the behaviour on the strained side, when their expansion does not exceed the investigated limitis of <60 circumferential expansion and crack depth of 0,3 t. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Soluble starch?based biodegradable and microporous microspheres (SDM-Ms) were prepared by emulsion chemical cross-linking technique using trisodium trimetaphosphate (TSTP) as the cross-linker. The resultant amorphous SDM-Ms were excellently identified by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). The internal rupture and surface-controlled erosion were the predominant degradation mechanisms for SDM-Ms. The obtained SDM-Ms were applied to adsorb coix seed oil (CSO) by immersing method. The adsorption capacity of CSO within SDM-Ms was determined, namely 0.5238?g/g, and the thermal stability was shown higher than that of the free CSO. A burst release appeared in the second hour, followed by controlled release. Diffusion, d...

Energy Technology Data Exchange (ETDEWEB)

To evaluate the effectiveness of percutaneous mechanical declotting. Using a 7-F Desilets-Hoffman sheath and the crossed-catheter technique, we aspirated the intragraft clot and pushed the residual clot into the central circulation with balloon catheters. The success rate, procedure time, complications and patency rates were evaluated. Technical success was achieved in 24 of 32 cases, with a procedure time of 30-240 (average, 111) minutes. In five of eight cases in which technical failure occurred, the guide wire failed to reach the stenotic site and in the other three, there was insufficient luminal dilatation. Complications included vein ruptures (n=2), arterial emboli (n=1) and arterial dissection (1), but there was no evidence of clinical symptoms of pulmonary embolism. The six-month patency rate was 67.8%. Mechanical declotting of thrombosed dialysis graft using a balloon catheter is relatively inexpensive, safe and fast, and is well tolerated. (author)

British Library Electronic Table of Contents (United Kingdom)

Vanadium carbide is the most effective grain growth inhibitor for ultrafine WC-Co composites due to its high solubility and mobility in the cobalt phase at relatively low temperatures; however, there are still some debates over the best way to introduce it into the WC-Co formulation. In this paper, the differences between admixed and chemically doped grain growth inhibitors on the microstructural development and properties of an ultrafine WC-10Co composite are discussed. The densification rate of chemically doped samples is slower in the early stage of sintering and the WC grain sizes of the sintered alloys are finer than those of admixed samples, leading to the increase of hardness and transverse rupture strength of the sintered alloys. The effectiveness of the chemically doped inhibitor ...

Energy Technology Data Exchange (ETDEWEB)

The effects of boron addition on weldability and high temperature strength properties were investigated for Hastelloy alloy XR used TIG welding process with the filler metals. Four versions of filler metals with different boron contents were used. The results obtained may be summarized as follows: (1) The influence of boron addition on weldability was not observed within the range of the present experiment. (2) The result of chemical analysis for deposited metals showed that boron desorption did not occur during welding. (3) The tensile properties of weldments, particularly in high temperature ductility were raised with increasing boron content. (4) In the creep properties of weldments, creep rupture life increased with increasing boron content under the given stress conditions. (author).

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of single-fiber pullout tests for deformed and smooth steel fibers embedded in the newly developed very-high strength concrete (VHSC) matrixes. The pullout test program involved four types of steel fibers, eight compressive strengths of VHSC matrixes, and two normal concrete strengths. Test results have shown that pullout behavior of different steel fiber reinforced VHSC composites is influenced by the matrix strength and fiber end condition (smooth, flat end, or hooked). Results reveal that both maximum pull-out load and total pullout energy increases as matrix strength increases for all deformed fibers that did not rupture. The test results also indicated that the increase in total pullout energy is more significant than that in peak load.

International Nuclear Information System (INIS)

The calculations presented are based on RELAP5/MOD2-3 input for VVER 440/213 Bohunice NPP, developed within the framework of IAEA TC Project by an international team of specialists from CSFR, Hungary, Bulgaria and Poland. Project activities were condentrated on input data refinement and testing. Several cases were calculated using the latest version of RELAP5/MOD2 provided by RMA, Albuquerque to investigate some modelling assumptions, such as break location, geometrical representation of secondary circuit piping as well as the effect of deactivation of the signal controlling the SG isolation valves. (2 refs., 21 figs., 2 tabs.).

Energy Technology Data Exchange (ETDEWEB)

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions. Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.

Energy Technology Data Exchange (ETDEWEB)

The high-nickel austenitic alloy 800 (in both the mill-annealed and the solution-treated grades) has several attractive properties that make it a good candidate for service attractive properties that make it a good candidate for service at elevated temperatures in corrosive environments. One such property is creep resistance. This report analyzes the elevated-temperature creep behavior of the mill-annealed grade, generally referred to simply as alloy 800. (The solution-treated grade is known as alloy 800H). Available data over the temperature range from 538 to 760/sup 0/C were collected and evaluated to yield mathematically approximations for creep-rupture and strain-time behavior for use in design calculations. However, the creep behavior of this material is extremely complex, and the analysis presented here contains substantial uncertainties. All results in this report should be considered preliminary because of limited data currently available. 20 figures.

Energy Technology Data Exchange (ETDEWEB)

A monolithic micromachined waveguide device or devices with low-loss, high-power handling, and near-optical frequency ranges is set forth. The waveguide and integrated devices are capable of transmitting near-optical frequencies due to optical-quality sidewall roughness. The device or devices are fabricated in parallel, may be mass produced using a LIGA manufacturing process, and may include a passive component such as a diplexer and/or an active capping layer capable of particularized signal processing of the waveforms propagated by the waveguide.

International Nuclear Information System (INIS)

The propagating of tachyons in an expanding universe is discussed. It is shown that a primordial tachyon in the big-bang universe cannot survive unless it had very large energy initially. In an indefinitely expanding universe the tachyon trajectory turns back in time. This time barrier is found to exist even in the quantum mechanical discussion of tachyons. This property is used to set limits on the mass of a tachyon. The possible astronomical checks on the hypothesis that neutrinos or photons may be tachyonic are also discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

Off-shell amplitudes for the open bosonic string and the closed spinning string are considered. Due to the presence of corners on the open string world sheet, strict Weyl invariance is broken. A consistent gauge-fixing procedure to treat this anomaly is described. Factorization of amplitudes with one or two off-shell strings and any number of on-shell tachyons is established. An attempt is made to construct a propagator for the spinning string. The inherent ambiguities in the choice of boundary conditions for the fermionic coordinates are outlined.

Energy Technology Data Exchange (ETDEWEB)

The concept of the minimum propagating zone (MPZ) is used to examine the causes of quenches in ISABELLE cosine theta superconducting dipole magnets. The size of disturbances large enough to exceed the MPZ and initiate quenches is estimated and compared with the size of disturbances which may be produced in the magnets. A suggestion for reducing the size of these disturbances through individual support of the coil block is outlined.

CERN Document Server

We discuss optimal detection of fast radio transients from astrophysical objects while taking into account the effects of propagation through intervening ionized media, including dispersion, scattering and scintillation.Our analysis applies to the giant-pulse phenomenon exhibited by some pulsars, for which we show examples, and to radio pulses from other astrophysical sources, such as prompt radio emission from gamma-ray burst sources and modulated signals from extra-terrestrial civilizations.

CERN Document Server

In this paper, the authors report on the electrical and thermal properties of Bi-2223 composite conductors prepared by the "accordion-folding method" (AFM). Thermal behavior study on AFM Bi-2223 conductors similar to those that have been successfully used to assemble the cold stage of low-loss current leads for CERN, has been performed by using a newly developed experimental apparatus that is described in detail. (7 refs).

International Nuclear Information System (INIS)

This paper reviewed the current status of basic research in plant cell engineering, highlighted the application of embryo culture, double haploid (DH) technology, protoplast culture and somatic hybridization, somaclonal variation, rapid propagation, and bio-products production of plant-origin, and t he prospects. (authors)

Energy Technology Data Exchange (ETDEWEB)

This book presents the papers given at a conference on offshore platforms. Topics considered in this book include risk assessment, crack propagation, fracture control, stress corrosion, the reliability of pile foundations, the thermal conductivity of offshore pipeline coating material, economic analysis, hydrodynamics, simulation, Arctic structure design, composite materials, buoys, deep water drilling, corrosion protection, pollution control equipment, and subsea exhaust gas compressors.

Energy Technology Data Exchange (ETDEWEB)

We use the method of Padg approximants and Fourier transform techniques to treat analytically the problem of transverse and longitudinal mode evolution in FELs. We obtain simple relations providing a transparent understanding of the dynamic of pulse propagation effects and of transverse mode guiding. We discuss the interplay with inhomogeneous broadening effects and derive gain formulae including longitudinal and transverse mode couplings.

CERN Document Server

Assuming the gluon field is well approximated by instanton configurations we derive a light quarks determinant and calculate its contribution to the specific heavy quarks correlators -- namely, the heavy quark propagator and heavy quark-aniquark correlator, receiving the instanton generated light-heavy quarks interaction terms contributions. With these knowledge we calculate the light quark contribution to the interaction between heavy quarks, which might be essential for the properties of a few heavy quarks systems.

Energy Technology Data Exchange (ETDEWEB)

T. D. Lee's method for developing the Feynman rules for gauge fields in a cavity is reformulated in terms of path integral. His work is then extended by deriving these rules, in the Feynman gauge, for a spherical cavity. In any gauge only the gauge particle propagator is altered, while all the Feynman rules for gauge field couplings are left unaltered by the presence of a dielectric medium.

British Library Electronic Table of Contents (United Kingdom)

Layered carbon fiber mats have been prepared by layer-by-layer (LBL) electrospinning of polyacrylonitrile onto thin natural cellulose paper and subsequent carbonization. The layered carbon fiber mat has been proved to be a promising microbial fuel cell anode for high density layered biofilm propagation and high bioelectrocatalytic anodic current density.

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work was to establish the flammability limits of hydrogen in air for upward vertical flame propagation at elevated temperatures up to 350 deg and atmospheric pressure in a conventional stainless steel test tube apparatus, and to investigate the extent to which a prolonged exposure (i.e., residence time) of the mixture to elevated temperatures before spark ignition may influence the value of the flammability limits. 9 refs.

Energy Technology Data Exchange (ETDEWEB)

The existence of propagating spin waves above T/sub c/ in Ni and Fe has been widely accepted since this picture was first advocated in 1973. In this brief review of our current neutron scattering experiments on Fe and Ni we will present convincing evidence showing that this picture is incorrect. In addition, we will demonstrate that over wide ranges of ..omega.., q and temperature, both Fe and Ni follow a simple paramagnetic scattering function of the spin diffusion type. 19 references.

Energy Technology Data Exchange (ETDEWEB)

Independent calculations of the antiproton-to-proton ratio by Gaisser and Maurer and by Badhwar et al. have produced conflicting results which obscure the interpretation of recent measurements of cosmic ray antiprotons. A detailed reexamination of these calculations has been performed and these differences have been resolved. We find that the first calculation was essentially correct and the reported fluxes of antiprotons are significantly higher than expected for secondary antiprotons in conventional models of cosmic ray propagation, as indicated by other recent calculations.

Energy Technology Data Exchange (ETDEWEB)

A novel approach is presented to extract relevant parameters associated with the energy loss of ejectiles from nuclear reactions obtained by digitizing the signals of a Bragg curve spectrometer. New and more powerful computational paradigms allow a more thorough pulse-shape analysis. This is fulfilled using a back-propagation artificial neural network as a pattern identifier. The known problem of over-training is discussed.

Energy Technology Data Exchange (ETDEWEB)

Using the manifestly causal gluon propagator in the light-cone gauge, we evaluate two one-loop Feynman integrals which appear in the computation of the three-gluon vertex correction in the two-component formalism of the Yang-Mills gauge fields. We conclude that they both are finite for {omega} -> 2, where {omega} is the dimensional regulator. They belong to a class of finite one-loop light-cone integrals. (author). 7 refs.

International Nuclear Information System (INIS)

Pipe whip restraints are used in nuclear power plants in order to limit the consequences of ruptured pipe whip effects and are thus an important part of the plant safety concept. The design of these devices is based on the choice of adequate construction and computational analysis supported by experimental investigation. Pipe whip restraints should, by means of deforming components, be able to absorb the energy of a ruptured pipe accelerated by the fluid reaction force. Since the elastic deformation of the restraint material is not sufficient for this purpose, or would result in excessive anchor loads, pipe whip restraints must generally be designed to work in the plastic range. Two types of restraints are presented in this paper, including the description of their mode of operation, design and computation. A comparison and critical evaluation of the calculation methods presently available are also given. The range of methods covers those ...

International Nuclear Information System (INIS)

Dynamic pipe impact tests were performed in order to determine the impact conditions for which a 2 inch Schedule 80 carbon steel target pipe would not be broken if it were impacted during a pipe whip event created by a postulated break of an adjacent larger parallel pipe. Such pipe/pipe impact scenarios are of special interest for the feeder pipes of a CANDU reactor because the large number of closely spaced parallel feeder pipes that carry coolant between large primary system pipes and individual fuel channels in the reactor core makes it impractical to consider providing feeder pipe whip restraints. The testing which was performed involved simulating the behaviour of 3 inch and larger whipping pipes in order to study their impact with 2 inch target pipes pressurized at about 9 MPa with water at a temperature of about 290"0C. In a conservative simulation of the worst pipe/pipe impact event which it has been predicted could occur for adjacent parallel feeder pipes (when a whipping pipe ...

International Nuclear Information System (INIS)

Series of pipe rupture tests have been performed at the Japan Atomic Energy Research Institute to demonstrate the safety of the primary coolant circuits in the event of pipe rupture in nuclear power plants. The pipe whip tests have been conducted to study the dynamic response of the pipe and restraints. The results of the pipe whip tests using test pipes of 4-inch in diameter under the BWR LOCA conditions (285"0C, 6.8 MPa) were reported in the previous paper F8/5 of the 6th SMiRT. The present paper describes the results of the pipe whip tests using test pipes of 6-inch in diameter. The test pipe was made of Type 304 stainless steel and was 165.2 mm in outer diameter and 11.0 mm in thickness, and was fixed at the pipe support so that the length of the test section was 3000 mm. The restraints were made of Type 304 stainless steel and were 16.0 mm in diameter, and were set on the restraint support with the clearance of 100 mm. The overhang length ...

International Nuclear Information System (INIS)

The understanding of fission product deposition in realistic steam generator conditions is needed for release estimates in PSA studies, and for the design of efficient accident management procedures. This is considered very important because primary-to-secondary leakages risk dominant sequences in many plants. Furthermore, the decay heat of the fission product deposits adds to the thermal load to the steam generator tubes also in other sequences, especially in case of cold leg leakages. This brings out the concern of induced steam generator tube ruptures in cases, where the steam generators are initially intact. The experimental data showed that the highest deposited fraction within the tubes were found in cases with lowest flow velocities. The minimum value of the deposited fraction was observed at intermediate flow velocities. With these relatively low Reynolds numbers, the results calculated with deposition models agree well with the experiments. At high ...

International Nuclear Information System (INIS)

Long-term disposal and management of low and intermediate-level radioactive waste is a major project of the nuclear power industry. Therefore, the selection of an underground waste repository has to be a geologically and seismologically stable storage. Easy transportation and emplacement is essential. The Wolsung nuclear power plant (NPP) of unit no. 1/2/ 3/ 4, which is responsible for the future of the energy industry, has already been constructed at the Wolsung site and a New NPP has recently been created at the Sinwolsung site. Radioactive waste used in the plant facilities, has piled up increasingly every year, but it should be taken to be managed at long-term underground storage disposal facilities. The Wolsung site for radioactivity waste repository was known to be relatively stable through various geological surveys, earthquakes, groundwater, engineering testing and analysis, but still more research related to the stability of the structure, in deep ...

Energy Technology Data Exchange (ETDEWEB)

Sensor has been developed for the measurement of seismic wave rotary components. The vertical axis rotary component sensor is constituted of four L22Ds, similar to each other in performance, fixed in a ring formation on a metal bed. The ring is 22cm in diameter, and the four coils are connected so that their outputs will be added up. A horizontal axis rotary component sensor is built in the similar way. The rotary component sensors are all connected to a spectrum analyzer for the measurement of micromotions. It is found that the four-L22D combination can detect a rotary component of 335mV/deg/s. The sensor can detect both vertical and horizontal components with roughly the same sensitivity. A ring-form combination of conventional electromagnetic seismometers, though only as a temporary expedient, can perform high-resolution detection of rotary components and determine the absolute values of earthquakes or noise levels. In the case of a gyrosensor available on the ...

Energy Technology Data Exchange (ETDEWEB)

The requirements to design nuclear power plants for the effects of an instantaneous double-ended guillotine break (DEGB) of the reactor coolant piping have led to excessive design costs, interference with normal plant operation and maintenance, and unnecessary radiation exposure of plant maintenance personnel. This report describes an aspect of the NRC/Lawrence Livermore National laboratory-sponsored research program aimed at investigating whether the probability of DEGB in Reactor Coolant Loop Piping of nuclear power plants is acceptably small such that the requirements to design for the DEGB effects (e.g., provision of pipe whip restraints) may be removed. This study estimates the probability of indirect DEGB in Reactor Coolant piping as a consequence of seismic-induced structural failures within the containment of the GE supplied boiling water reactor at the Brunswick nuclear power plant. The median probability of indirect DEGB was estimated to be 2 x 10/sup -8/ per year. Using ...

Energy Technology Data Exchange (ETDEWEB)

Faults are being actively investigated across Japan since the Great Hanshin-Awaji Earthquake. Discussed in this report is the application of the 3D near-surface reflection seismic survey in big cities. Data from trenching and drilling is used for the geological interpretation of the surroundings of a fault, and the reflection seismic survey is used to identify the position, etc., of the fault. In this article, when the results obtained from the experimental field are examined, it is found that the conventional 2D imaging reflection survey betrays the limit of its capability when the geological structure is complicated, that the 3D reflection seismic survey, on the contrary, is capable of high-precision imaging and, when augmented by drilling, etc., becomes capable of a more detailed interpretation, and that it also contributes effectively to the improvement of local disaster prevention in big cities. Using as the model the Tachikawa fault that runs near JR ...

International Nuclear Information System (INIS)

The 105-KE and 105-KW Fuel Storage Basins were constructed more than 35 years ago as repositories for irradiated fuel from the K East and K West Reactors. Currently, the basins contain irradiated fuel from the N Reactor. To continue to use the basins as desired, seismic adequacy in accordance with current US Department of Energy facility requirements must be demonstrated. The 105-KE and 105-KW Basins are reinforced concrete, belowground reservoirs with a 16-ft water depth. The entire water retention boundary, which currently includes a portion of the adjacent reactor buildings, must be qualified for the Hanford Site design basis earthquake. The reactor building interface joints are sealed against leakage with rubber water stops. Demonstration of the seismic adequacy of these interface joints was initially identified as a key issue in the seismic qualification effort. The issue of water leakage through seismicly induced cracks was also investigated. This issue, ...

Energy Technology Data Exchange (ETDEWEB)

This is a prompt report. These days the importance of acquiring knowledge about the structure from the lower crust down to the upper mantle is often discussed with reference taken to Hyogo-ken Nanbu Earthquake. The Hidaka collision belt where the lower crust is exposed on the surface is a rare phenomenon in the world and has been the subject of seismic survey. As a part of the survey, experiments are conducted by the use of vibrations produced by Vibroseis and dynamite sources. Every one of the shot records (20-second record) from the two types of vibration sources contains a clear echo in the vicinity of 16 seconds supposedly from a level deeper than 40 kilometers, not to mention reflections from shallow levels. Although some studies have to be conducted before the reflecting geological boundary (possibly the upper mantle) of the echo near the 16-second point can be identified, yet this is probably the reflection from the deepest level ever obtained in the seismic ...

International Nuclear Information System (INIS)

In Japan, high rigidity reinforced concrete foundations called the high-tuned type foundation have been generally used for the turbine generator foundations. In Europe, on the other hand, flexible steel foundations and spring-mounted reinforced concrete foundations are employed. These are called the low-tuned type foundation and have following excellent characteristics. (1) Excellent vibration isolation ability (2) By reducing the structural member size and weight, more effective utilization of space under the deck is possible. However, the low-tuned type foundation has a lower seismic resistance and it is said to be unsuitable type foundation in frequent seismic countries such as Japan and USA etc. from the view point of safety against earthquake. We have developed the new type low-tuned foundation having its excellent characteristics and seismic resistance ability called the spring-mounted turbine generator foundation supported by turbine house structure. This ...

Science.gov (United States)

The millimeter microwave source of gyrotron-traveling-wave amplifier (gyro-TWT) is capable of generating high power coherent radiation in a broad bandwidth, while its performance is severely deteriorated by the stability problems. This paper focuses on modeling and the stability analysis of the Naval Research Laboratory (NRL) Ka-band TE{sub 01} mode gyro-TWT based on an interaction circuit alternately loaded with lossy ceramic shells and metal rings. The propagation characteristics of the interaction circuit is analyzed first, based on which the boundary impedance method is employed to build an equivalent uniform lossy circuit. Then the stability of the interaction system is studied using linear and nonlinear theories. The analysis reveals that, due to the special waveguide structure and the dielectric loss, the propagation characteristics of the complex waveguide are similar to that of a uniform lossy circuit. The analysis of the absolute ...

Energy Technology Data Exchange (ETDEWEB)

A first-order one-way wave system has been created based on characteristic analysis of the acoustic wave system and optimization of the dispersion relation. The authors demonstrate that this system is equivalent to a third-order scalar partial-differential equation which, for a homogeneous medium, reduces to a form similar to the 45{degree} paraxial wave equation. This system describes accurately waves propagating in a 2D heterogeneous medium at angles up to 75{degree}. The one-way wave system representing downgoing waves is used for a modified reverse time migration method. As a wavefield extrapolator in migration, the downgoing wave system propagates the reflection events backwards to their reflectors without scattering at the discontinuities in the velocity model. Hence, images with amplitudes proportional to reflectivity can be obtained from this migration technique. They present examples of the application of the new migration method to ...

Energy Technology Data Exchange (ETDEWEB)

In the framework of the feasibility study of radioactive waste disposal in deep geologic formations, a clay formation (named 'argilite de l'Est') has been selected in the Meuse-Haute Marne region (France) for the construction of an underground laboratory. The percolation of alkaline solutions through the argilite has been studied using column experiments with short residence times (30 min). These experiments simulate the leaching of a cement which could be used in the building materials of the laboratory. The alkaline solutions used are mono-cationic solutions of calcium, sodium and strontium. The behaviour of calcium is differentiated from the other cations. For all alkaline solutions (NaOH, Ca(OH){sub 2} or Sr(OH){sub 2}) chemical reactions consuming both hydroxide ions and their associated cations have been evidenced. These reactions are heterogenous reactions of surface adsorption by site ionization. The calcium has a different behaviour, more complex, ...

International Nuclear Information System (INIS)

We show that a general variant of the Wick theorems can be used to reduce the time ordered products in the Gell-Mann and Low formula for a certain class on non local quantum field theories, including the case where the interaction Lagrangian is defined in terms of twisted products. The only necessary modification is the replacement of the Stueckelberg-Feynman propagator by the general propagator (the 'contractor' of Denk and Schweda) D(y-y';#tau#-#tau#')=(1)/i(#DELTA#_+(y-y')#theta#(#tau#-#tau#')+#DELTA#+(y'-y)#theta#(#tau#'-#tau#)), where the violations of locality and causality are represented by the dependence of #tau#,#tau#' on other points, besides those involved in the contraction. This leads naturally to a diagrammatic expansion of the Gell-Mann and Low formula, in terms of the same diagrams as in the local case, the only necessary modification concerning the Feynman rules. The ordinary local theory is easily recovered as a special case, ...

Energy Technology Data Exchange (ETDEWEB)

The two-dimensional Eulerian hydrodynamic code 2DE, with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities into explosives, initiated by a low-velocity jet, are significantly less than for ...

Energy Technology Data Exchange (ETDEWEB)

This paper develops a clear procedure for solving the nonlinear Vlasov-Maxwell equations for a one-component intense charged particle beam or finite-length charge bunch propagating through a cylindrical conducting pipe (radius r = r(subscript)w = const.), and confined by an applied focusing force. In particular, the nonlinear Vlasov-Maxwell equations are Lorentz-transformed to the beam frame ('primed' variables) moving with axial velocity relative to the laboratory. In the beam frame, the particle motions are nonrelativistic for the applications of practical interest, already a major simplification. Then, in the beam frame, we make the electrostatic approximation which fully incorporates beam space-charge effects, but neglects any fast electromagnetic processes with transverse polarization (e.g., light waves). The resulting Vlasov-Maxwell equations are then Lorentz-transformed back to the laboratory frame, and properties of the self-generated ...

Energy Technology Data Exchange (ETDEWEB)

A 25m wind turbine blade was tested to failure when subjected to a flapwise load. With the test setup, it was possible to test the blade to failure at three diffe-rent locations. The objective of these tests is to learn about how a wind turbine blade fails when exposed to a large flapwise load and how failures propagate. The report shows also results from ultra sonic scan of the surface of the blade and it is seen to be very useful for the detection of defects, especially in the layer between the skin laminate and the load carrying main spar. Acoustic emission was successfully used as sensor for the detection of damages in the blade during the test. The report contains measurements of the total deflection of the blade, the local deflection of the skin and the load carrying main spar and also measurement of strain all as a function of the applied load and up to failure of the blade. The 'post mortem' analysis and description of how the damages ...

International Nuclear Information System (INIS)

The combined effects of environment, yield strength and stress state on the cracking susceptibility of beta-extruded Ti-6Al-6V-2Sn have been examined. At a constant yield strength and under plane strain conditions, the stress intensity required for slow crack propagation decreased as the severity of the environment increased, i.e., from laboratory air to 3.5% NaCl. Furthermore, the crack propagation rates were a function of both stress intensity, and environmental severity. Although the fracture toughness and threshold stress intensities for slow crack growth generally decreased with increasing yield strength, aging, which resulted in the precipitation of ordered Ti3Al particles in the primary alpha phase, tended to accentuate the susceptibility of this alloy to sustained load/stress corrosion cracking. Finally, at constant yield strength, the sustained load cracking threshold stress intensity was a function of stress state.

International Nuclear Information System (INIS)

We present first-time measurements of the Fermi surface and low-energy electronic structure of intermetallic compounds Gd_2PdSi_3 and Tb_2PdSi_3 by means of angle-resolved photoelectron spectroscopy (ARPES). We show that the Fermi surface in both compounds consists of an electron barrel at the #GAMMA# point surrounded by spindle-shaped electron pockets originating from the same band, with the band bottom of both features lying at 0.5 eV below the Fermi level. From the experimentally measured band structure, we estimate the momentum-dependent RKKY coupling strength and demonstrate that it is peaked at the 1/2#GAMMA# K wave vector. Comparison with neutron diffraction data from the same crystals shows perfect agreement of this vector with the propagation vector of the low-temperature in-plane magnetic order, thereby demonstrating the decisive role of the Fermi surface geometry in explaining the complex magnetically ordered ground state of ternary rare earth silicides.

Energy Technology Data Exchange (ETDEWEB)

Today`s nuclear power plants are marked by increasing needs for non-destructive inspection techniques in preventive maintenance programs. Additionally, it is becoming more important to evaluate residual stress which may be a key parameter for crack propagations in welded pipings. The authors have developed an ultrasonic velocity measurement method which obtains ultrasonic velocity changes by residual stress with a high accuracy. The ultrasonic velocity measurement is composed of three procedures. They are as follows. (1) Highly accurate propagation time measurements; (2) Pipe thickness correction; (3) Residual stress evaluation. The ultrasonic velocity measurements have been applied to the residual stress evaluation of carbon steel welded pipings. Destructive testing using stress strain gauges was done after the ultrasonic non-destructive evaluation of the residual stress. The experimental results verified that residual stress in carbon steel ...

Energy Technology Data Exchange (ETDEWEB)

Cuttings were taken from the upper part of the crowns of spruce trees 60-70 yr old in stands at 3 different altitudes in the Rila Mountains and 4 in the Vitosha Mountains in Bulgaria. The cuttings, of 1-yr, 2-yr and 3-yr shoots, were rooted in sand, perlite and peat. Rooting % generally decreased with increasing altitude of provenance, but cuttings from the very highest altitudes showed increased rooting %. In general, 1-yr cuttings gave the best rooting %, but in some provenances the 2-yr cuttings were best. Sand was clearly the best rooting substrate. (Refs. 11).

International Nuclear Information System (INIS)

Thomson scattering is the process in which a low-energy photon scatters from a free electron. When a laser pulse propagates through a plasma, the spectrum of the scattered light due to the Thomson scattering is proportional to the power spectrum of the electron density fluctuations, i.e., dynamic form factor, from which various plasma parameters can be inferred, such as electron temperature and plasma flow velocity. After years of development. Thomson scattering has now become a powerful diagnostic tool of plasma physics. (authors)

British Library Electronic Table of Contents (United Kingdom)

The objective of this paper is to analyze the implications of varying degrees of financial openness for the impact of technology shocks on a real, small open economy with financial and informational frictions. Aggregate fluctuations and propagation mechanisms under increasing financial openness are investigated in a dynamic, stochastic, general equilibrium framework in the case of positive technology shocks. The imperfections in the economy in the form of informational asymmetries among the agents and uncertainty in the production process necessitate financial intermediation and collateralized borrowing in the economy. The reason to abstract from money in the setup of the framework is to be able to concentrate on the real implications of increasing financial openness for the effect of tech...

International Nuclear Information System (INIS)

This report is devoted to the investigation of the influence of electron collisions and radial non-uniformity of plasma density on phase characteristics, spatial attenuation and wave field structure of slow symmetric electromagnetic waves that propagate along cylindrical waveguide structure. It has been shown that collision rate and radial non-uniformity of plasma density for various parameters of waveguide structure and dielectric affect essentially on the wave characteristics and consequently, on the parameters of gas discharge that is sustained by this wave. The results obtained are of large importance for the construction of the theory of gas discharges that are sustained by the surface electromagnetic waves.

CERN Document Server

We show the propagation of regularity, uniformly in time, for the scaled solutions of the inelastic Maxwell model for small inelasticity. This result together with the weak convergence towards the homogenous cooling state present in the literature implies the strong convergence in Sobolev norms and in the $L^1$ norm towards it depending on the regularity of the initial data. The strategy of the proof is based on a precise control of the growth of the Fisher information for the inelastic Boltzmann equation. Moreover, as an application we obtain a bound in the $L^1$ distance between the homogeneous cooling state and the corresponding Maxwellian distribution vanishing as the inelasticity goes to zero.