Science.gov (United States)

Certain materials, especially Sn, passivate the rare earth-exchanged Y zeolite (REY) used in petrochemical fluid-cracking catalysts against vanadium degradation caused by V impurities in the feed oil. The mechanism of passivation was investigated here from the standpoint of high-temperature oxide acid-base reaction; i.e., where the controlling factors were considered to be Lewis acid-base reactions between V{sub 2}O{sub 5}, the RE oxides, SnO{sub 2}, etc. Molten salt tests at 680{degree}C showed SnO{sub 2}, presumably because of its acidic nature, to be essentially nonreactive with V{sub 2}O{sub 5} or Na{sub 2}O-V{sub 2}O{sub 5} compounds. A hypothesis was developed to explain how the passivation effect by Sn might result from the unique resistivity of SnO{sub 2} to reaction with V{sub 2}O{sub 5}.

Energy Technology Data Exchange (ETDEWEB)

Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the ...

Energy Technology Data Exchange (ETDEWEB)

Results on the oxidative dehydrogenation of ethane on rare-earth oxide (REO) based catalysts (Na-P-Sm-O, Sm-Sr(Ca)-O, La-Sr-O and Nd-Sr-O) are described. Oxygen adsorption was found to be a key factor which determines the activity of this type of catalysts. Continuous flow experiments in the presence of catalysts which reveal strong oxygen adsorption showed that the reaction mixture is ignited resulting in an enhanced heat generation at the reactor inlet. The heat produced by the oxidative reactions was sufficient under the conditions chosen for the endothermic thermal pyrolysis which takes place preferentially in the gas phase. Ignition of the reaction mixture is an important catalyst function. Contrary to non-catalytic oxidative dehydrogenation, reaction temperatures above 700 C could be achieved without significant external heat input. Ethylene yields of up to 34-45% (S=66-73%) ...

Energy Technology Data Exchange (ETDEWEB)

In the dehydrodesulfurization of ethanethiol at 400/sup 0/C, the activities of sodium X, Y, and A zeolites decreased in the order given as did the activities of nickel, cobalt, zinc, cadmium, copper, silver, lead, manganese, barium, calcium, sodium, and iron Y zeolite catalysts. A volcano-shape order was observed between the catalytic activity and the electronegativity of the metal ions. The changes in the activity of hydrogen Y zeolite catalyst in ethanethiol dehydrodesulfurization and cumene dealkylation by calcination agreed with the decrease in the Broensted acidity but were independent of Lewis acidity. For hydrodesulfurization of thiophene, the activities of nickel, cobalt, copper, and silver Y zeolite catalysts decreased in the order given and were greater than for a commercial hydrodesulfurization catalyst; reduced and presulfided catalysts showed selective ...

Science.gov (United States)

Hie synthesis of diverse biologically important compounds, under condi- tions which existed on the earth in the initial period of its evolution, ha; ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents an analysis of the performance of a selective emitter using small particles of rare earth compounds stable at high temperatures in a low emittance inert gas stream. An expression for the spectral emissive power excluding radiation scattering was derived to include the radiation in the emission band, produced by electronic transitions of the rare earth ion, and the continuum radiation outside the emission band produced by the rare earth host. Preliminary results suggest that a selective emitter based on suspended rare earth oxide particles will have high efficiency and merits further experimental investigation. {copyright} {ital 1996 American Institute of Physics.}

Energy Technology Data Exchange (ETDEWEB)

Mineral matter in coals is important in various senses for coal liquefaction. It is possible that the catalytic activity is affected by the interaction between catalyst and mineral matter. Iron-based catalyst forms pyrrhotite in the process of liquefaction, but the interaction between it and mineral matter is not known in detail. In this study, the interaction between mineral matter and catalyst and the selective reaction between them were investigated. Tanito Harum coal was used for this study. This coal contains a slight amount of siderite and jarosite besides pyrite as iron compounds. Liquefaction samples were obtained from the 1 t/d NEDOL process PSU. The solid deposits in the reactor mainly contained pyrrhotite and quartz. A slight amount of kaolinite was observed, and pyrite was little remained. It was found that the catalyst (pyrrhotite) often coexisted with quartz, clay and ...

Energy Technology Data Exchange (ETDEWEB)

This semiannual report for the period October 1983-March 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogen transfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: the use of pyrene as a chemical probe of catalyst activity; analysis of catalysts from Wilsonville run 242 using ESCA; atmospheric pressure model compound activity testing of regenerated catalysts from Wilsonville ...

British Library Electronic Table of Contents (United Kingdom)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two sha...

International Nuclear Information System (INIS)

We present a study of the crystal field in PrNiAl, NdNiAl, ErNiAl and ErCuAl intermetallic compounds based on inelastic neutron spectroscopy. These compounds crystallize in the ZrNiAl-type hexagonal structure with an orthorhombic symmetry on rare-earth sites. The results are compared with the specific-heat data, and the lower parts of the crystal-field energy-level schemes are determined. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The rare earth antimonates RE{sub 3}Sb{sub 5}O{sub 12} constitute an isostructural series, where the rare earth site symmetry is S{sub 4}. The spectroscopic properties of pure or doped compounds of this family are studied in order to derive their energy level schemes and to simulate them through the crystal field theory, by using the approximated D{sub 2d} potential. The paramagnetic susceptibilities are calculated with the derived wavefunctions and compared to experiment.

Energy Technology Data Exchange (ETDEWEB)

This quarterly report for the period April through June 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogen transfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: analysis of catalyst samples from Wilsonville Run 246; catalyst presulfiding; catalyst activity testing using pyrene as a chemical probe; catalyst deactivation using a high-pressure model ...

International Nuclear Information System (INIS)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO2, PrO2), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion ...

Science.gov (United States)

The isomerization of neopentane has been investigated over the 0.76 wt% Pd/SiO{sub 2} catalyst. It is found that after high temperature reduction (HTR, at 873 K) the selectivity for isomerization is much higher than that after low temperature reduction (LTR, at 573 K). A variety of experiments, including kinetic, chemisorption (O{sub 2}, H{sub 2}, and CO), temperature-programmed desorption of H{sub 2}, and X-ray diffraction, showed that this selectivity enhancement cannot be interpreted in terms of H{sub 2} retention by catalyst. Instead, the formation of Pd-Si compound(s) (most probably Pd{sub 3}Si) during HTR seems immediately responsible for the catalytic behavior of HTR Pd/SiO{sub 2} catalysts. A mechanism is proposed for the Pd-SiO{sub 2} interaction in which Pd atoms (or ions) are incorporated into the silica support (via oxygen vacancies) and a new phase of palladium silicide is formed. ...

Energy Technology Data Exchange (ETDEWEB)

Red mud, and red mud activated by dissolution in hydrochloric acid and reprecipitation with ammonia, were tested as catalysts for the hydrogenation of an anthracene oil in a trickle-bed reactor. Conversion data were determined for the different polyaromatic compounds in the anthracene oil. Red mud shows appreciable catalytic activity, which is enhanced by the activation. Although both red mud and activated red mud are less active than a commercial Ni-Mo/[gamma]-alumina hydrotreating catalyst, the difference in activity is smaller when conversion to hydroaromatics instead of total conversion of reactants is considered. 20 refs., 8 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption was possible on minerals that are thought to have been ...

International Nuclear Information System (INIS)

We have investigated the superconducting and metallurgical properties of the ternary compounds RPd_2Si_2 and RRh_2Si_2 with R = Y, La, and Lu. All RPd_2Si_2 compounds and LaRh_2Si_2 were found to be type-I superconductors below 1 K. A detailed metallurgical analysis shows that segregation of second phases can easily mask the intrinsic (stoichiometric ratio 1:2:2) intermetallic-compound properties. Two sample-preparation techniques, viz., single crystals and off-stoichiometry, were utilized to establish where bulk superconductivity occurs. The type-I behavior of these compounds is explained with an analogous model as is used for the heavy-fermion superconductors CeCu_2Si_2 and URu_2Si_2.

Energy Technology Data Exchange (ETDEWEB)

Magnetic properties of polycrystalline samples of RPd/sub 2/Si compounds (R = Gd, Tb, Dy, Ho and Er) are presented. The Gd and Tb based compounds are antiferromagnetic with Neel temperatures of 13.5 and 21 K respectively. For both compounds a metamagnetic transition is observed in low field. Moreover, in TbPd/sub 2/Si a transition between two different antiferromagnetic phases is observed at 8.5 K. The Dy, Ho and Er based compounds are ferromagnetic with Curie temperatures of 9, 3.5 ad 2.8 K respectively. The observed properties result from indirect exchange interactions and crystal field effects acting on rare earth ions which lie in a very low symmetry site.

Science.gov (United States)

We discuss how magnetic phenomena affect superconductivity in simple metals, transition metals and alloys thereof, and dilute Rare-Earth alloys. It is shown both qualitatively and quantitatively that superconductors are sensitive probes for studying itinerant spin excitations, local spin excitations associated with nearly magnetic impurities, the effect of the atomic environment on the stability of local magnetic moments, and the nature of the spin order in Rare-Earth alloys. Also, we discuss how magnetic impurities can be used to study the electronic configuration which is responsible for superconductivity in Laves-phase crystals like A-15 compounds and ..beta..-W crystals, for example.

International Nuclear Information System (INIS)

A process is described for the selective oxidation of ammonia to nitric oxide in about 90% or greater yield with a minimum of nitrogen or dinitrogen oxide (N/sub 2/O) as by-products, comprising: (1) contacting gaseous ammonia in an oxygen containing gas optionally with an inert gaseous diluent with a mixed metal perovskite catalyst of the general formula: ABO/sub 3/, wherein: A is selected from the alkali, alkaline earth, lanthanide, or actinide metals or a mixture of these metals having a relatively large ionic, radius, and B is selected from an element or a combination of elements selected from Groups IB, IVB, VB, VIB, VIIB, or VIII of the Periodic Table, wherein the perovskite phase of the catalyst has an equilibrium partial pressure of oxygen at 1000"0C of greater than about 10/sup -15/ bar; and (2) heating the reactants of step (1) at greater than about 500"0C under conditions of 10 to 100,000 hr/sup -1/ hourly space ...

International Nuclear Information System (INIS)

The inverse susceptibilities of the monopnictides and monochalcogenides of the light rare earths plotted vs. temperature flatten off at high temperatures. This behaviour is well explained by van Vleck paramagnetism of the excited states of the multiplet. For almost all actinide pnictides and chalcogenides a similar flattening-off is observed. Since spin orbit coupling is much stronger than in the light rare earth compounds an analogous interpretation is not possible. Susceptibility curves for uranium compounds can be fitted by adding a temperature dependent enhanced Pauli paramagnetism to the Curie-Weiss term (modified Curie-Weiss law). The high temperature susceptibility behaviour of neptunium compounds is very similar to uranium compounds i.e. an appreciable deviation from the Curie-Weiss law is only visible for the chalcogenides. The plutonium chalcogenides ...

Science.gov (United States)

In the course of observing by means of Auger spectroscopy graphite gasification reactions catalyzed by metals, it has been found that in the presence of hydrogen, nickel appears to diffuse from the surface into the bulk of the graphite. When potassium is deposited on graphite, it is volatilized above 400/sup 0/C. Surprisingly the production of methane and carbon dioxide from the reaction of graphite and steam was catalyzed by potassium at as low a temperature as 250/sup 0/C. It has been shown that literature on the alkylation of benzene with synthesis gas is erroneous and that the products reported are due to Lewis acid catalyzed cracking of benzene. A novel cobalt mediated, reversible cleavage of a vinyl-hydrogen bond has been discovered. All products from the thermal decomposition of tetralin have been identified. The stereochemistry of cis-1, 2 dihydrotetralin was determined. In the utilization of the water gas shift reaction as a reducing agent for model coal ...

Science.gov (United States)

A process is provided for conducting organic compound conversion over a catalyst composition comprising a supported crystalline zeolite having a high initial silica-to-alumina mole ratio, said supported zeolite being prepared by compositing said crystalline zeolite with alumina, reacting the composite with a particular hydrogen fluoride solution in a specified way, drying the hydrogen fluoride reacted composite, treating the dried composite by hydrolysis, ammonolysis and/or by contact with an ammonium salt solution, and calcining the resulting material.

International Nuclear Information System (INIS)

The magnetization of a series of intermetallic compounds Au_3R, where R is Gd through Yb, was investigated at 2.5 to 300"0K in applied fields up to 26 kOe. All the compounds studied exhibited the orthorhombic TiCu_3--Do/sub a/ type structure. For high temperatures, the temperature dependence of the inverse susceptibility followed a Curie--Weiss law, yielding effective paramagnetic moments in good agreement with the values calculated for free tripositive rare earth ions. At low temperatures, deviations from Curie--Weiss behavior were observed in all cases. These deviations are ascribed to the influence of crystal-field and exchange interactions. (auth).

British Library Electronic Table of Contents (United Kingdom)

Two transition metal ions (Cu^2^+ and Co^2^+) and two rare earth metal ions (Ce^3^+ and La^3^+) were used as the assisted metal ions, respectively to prepare the transition metal and rare metal assisted Fe bimetallic amidoximated polyacrylonitrile (AO-PAN) fiber complexes. And their coordination configuration and visible light adsorption properties were examined by coordination number determination and UV-vis-DRS. Then the catalytic performance of these complexes was evaluated as the heterogeneous Fenton catalysts in Rhodamine B degradation by changing the nature and dosage of the assisted ions added. The results indicated that the incorporation of the assisted metal ions led to Fe bimetallic AO-PAN complexes with the more unsaturated configurations than Fe monometallic AO-PAN complex due ...

International Science & Technology Center (ISTC)

New Catalysts and Sorbents on the Basis of Pillared Clays for the Processes of Hydrocarbons Conversion and Water Purification

International Nuclear Information System (INIS)

New rare earth metal rich cadmium compounds RE_4CoCd and RE_4RhCd (RE = Tb, Dy, Ho) were prepared by high-frequency melting of the elements in sealed tantalum tubes. The samples were studied by x-ray powder and single-crystal diffraction. All the compounds crystallize with Gd_4RhIn-type structure, with space group F4-bar3m. The structures are built up from rigid three-dimensional networks of condensed, cobalt (rhodium) centred trigonal RE_6 prisms. The voids left by these networks are filled by Cd_4 cluster units and the coordination number 14 polyhedra of the RE1 atoms. The terbium and dysprosium compounds in both series undergo antiferromagnetic ordering, whereas the holmium compounds exhibit ferromagnetic ordering. The magnetic ordering in these compounds is characterized by broad peaks around the transition temperatures. The results of detailed ...

Science.gov (United States)

The Gateway to Astronaut Photography of Earth hosts the best and most complete online collection of astronaut photographs of the Earth.

Energy Technology Data Exchange (ETDEWEB)

A process is claimed for selectively preparing a mixture of two-carbon atom oxygenated hydrocarbons, namely, acetic acid, ethanol and acetaldehyde, by continuously contacting a gaseous reaction mixture containing hydrogen and carbon monoxide with a solid catalyst comprising rhodium in combination with one or more alkali metals selected from the group consisting of lithium, potassium, cesium and rubidium at reaction conditions correlated so as to favor the formation of a substantial proportion of such two-carbon atom products.

Energy Technology Data Exchange (ETDEWEB)

The crystal structure of borophosphates ABPO{sub 5} (A = alkaline earth or Pb) was resolved on a polycrystalline sample using the Rietveld method. The x-ray diffraction patterns data show that ABPO{sub 5} crystallize in a centrosymmetric space group P3{sub 1}21 and their structure is related to the borogermanates REBGeO{sub 5} with a stillwellite-type structure. Pr{sup 3+} ion was used as a local structural probe to corroborate the structural resolution results. Absorption and fluorescence spectra of A{sub 1-x}Pr{sub x}BP{sub 1-x}Ge{sub x}O{sub 5} (A alkaline earth or Pb; x = 0.05) have been investigated at different temperatures. At 9 K the 3{sup H}{sub 4}{yields}{sup 3}P{sub 0} transition of trivalent praseodymium ion (4f{sup 2} configuration) is observed as a single line. This indicates a unique crystallographic site for the rare earth ion in these compounds replacing the divalent cation. Energy ...

International Nuclear Information System (INIS)

The nine title compounds were prepared from the elements by arc-melting and subsequent heat treatment in resistance and high-frequency furnaces. The crystal structure of these isotypic compounds was determined for YPdSi from single-crystal X-ray diffractometer data: Pmmn, a = 430.8(1) pm, b = 1391.2(1) pm, c = 743.1(1) pm, Z = 8, R = 0.024 for 417 structure factors and 40 variable parameters. The crystal structures of the isotypic compounds GdPdSi and ErPdSi were also refined from single-crystal data. The structure is of a new type. It consists of condensed, six-membered rings of alternating palladium and silicon atoms with Pd-Si bond distances varying between 249.6 and 258.8 pm. These two-dimensionally infinite nets are connected to each other via weak Pd-Si and Si-Si bonds with bond distances of 276.3 and 259.5 pm. The rare earth atoms are situated above and below the six-membered palladium-silicon ...

British Library Electronic Table of Contents (United Kingdom)

Many important advances in the physics of strongly correlated electron systems have been driven by the development of new materials: for instance the filled skutterudites Formula Not Shown ( Formula Not Shown metal, alkaline earth, lanthanide, or actinide; Formula Not Shown , Ru, or Os; Formula Not Shown , As, or Sb), certain lanthanide and actinide intermetallic compounds such as Formula Not Shown and Formula Not Shown ( Formula Not Shown , Rh, or Ir), and layered oxypnictides and related materials. These types of complex multinary d- and f-electron compounds have proven to be a vast reservoir of novel strongly correlated electron ground states and phenomena. In these materials, the occurrence of such a wide range of ground states and phenomena arises from a delicate interplay between com...

Energy Technology Data Exchange (ETDEWEB)

Due to the increasingly stricter regulations for deep reduction of fuel sulfur content, development of new deep desulfurization processes for liquid transport fuels has become one of the major challenges to the refining industry and to the production of hydrocarbon fuels for fuel cell applications. The sulfur compounds in the current transport fuels corresponding to the S level of 350-500 ppm account for only about 0.12-0.25 wt % of the fuel. The conventional hydrotreating approaches will need to increase catalyst bed volume at high-temperature and high-pressure conditions for treating 100 % of the whole fuel in order to convert the fuel mass of less than 0.25 wt %. In the present study, we are exploring a novel adsorption process for desulfurization at low temperatures, which can effectively reduce the sulfur content in gasoline, jet fuel and diesel fuel at low investment and operating cost to meet the needs for ultra-clean transportation ...

Energy Technology Data Exchange (ETDEWEB)

In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially ...

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

Ternary R_2TSi_3 intermetallic compounds (R=Rare Earth, T=Transition Metal) with hexagonal AlB_2-type crystallographic structure are known because of their interesting physical properties. Pr_2PdSi_3 single crystals were grown by a vertical floating zone method. The compound exhibits congruent melting behavior at a liquidus temperature of about 1770 C. Single crystalline samples show a huge anisotropy at low temperatures due to the crystal electric field effect and order antiferromagnetically below the Neel temperature T_N=2.17 K. This value approximately obeys the linear de Gennes scaling for this class of compounds. The [001] orientation was identified as the magnetic easy axis at room temperature. At lower temperature (#approx#20 K) magnetic easy and hard axes interchange with each other. Two additional magnetic phase transitions were observed at temperatures below 1 K.

Energy Technology Data Exchange (ETDEWEB)

DC resistivity, dc magnetization, and specific heat of eight Sc/sub 5/Co/sub 4/Ge/sub 10/-type crystal structure compounds R/sub 5/T/sub 4/Ge/sub 10/ for R = Dy, Ho, Er, Tm, and T = Rh and Ir are presented. The resistivity, single crystal magnetization, and specific heat results show that in all those compounds, the magnetic moments order antiferromagnetically in the c direction at low temperature. However, in the Er and Tm compounds, the magnetizations along x-y hard directions do not show any anomalies above 2.0 K. This suggests that the ordered Er and Tm ions, which have positive quadrupole coefficients ..cap alpha../sub j/, interact with a crystal field that has an electronic potential valley along the c axis. The fitting of the hard axis magnetizations to Curie-Weiss law suggests that the resulting antiferromagnetic-like theta reflects the strength of the crystal field torque on the magnetic moments rather than the ...

Science.gov (United States)

Automated Transport. Not Studied in Detail. Earth's Neighborhood. Simplified Infrastructure. Mars. Earth-. Moon L. 1. Gateway. Moon. Earth-Sun L. 2. Science ...

International Nuclear Information System (INIS)

A rapid combustion unit (Baird and Tatlock) incorporating a combustion chamber provided with baffle plates for complete combustion of the sample without the use of a catalyst has been assembled in a glove box for the determination of carbon and hydrogen in actinide complexes. The unit has been modified employing a movable electric furnace and a proportional temperature controller, for decomposition of the sample at desired heating rates. The set-up was standardised employing various reference materials such as benzoic acid, acetanilide, sulphanilamide and 1-chloro 2:4 dinitrobenzene and the standard deviation in the measurements evaluated. It has also been used successfully for the determination of carbon in uranium carbide and carbon and hydrogen in some uranyl-#beta#-diketone-amine N-oxide complexes and in plutonium(IV) oxalate. (auth.).

International Nuclear Information System (INIS)

Three new rare earth metal-rich compounds, Gd_4NiTe_2, and Er_5M_2Te_2 (M=Ni, Co), were synthesized in direct reactions using R, R_3M, and R_2Te_3 (R=Gd, Er; M=Co, Ni) and single-crystal structures were determined. Gd_4NiTe_2 is orthorhombic and crystallizes in space group Pnma with four formula units per cell. Lattice parameters at 110(2)K are a=15.548(9), b=4.113(2), c=11.7521(15)A. Er_5Ni_2Te_2 and Er_5Co_2Te_2 are isostructural and crystallize in the orthorhombic space group Cmcm with two formula units per cell. Lattice parameters at 110(2)K are a=3.934(1), b=14.811(4), c=14.709(4)A, and a=3.898(1), b=14.920(3), c=14.889(3)A, respectively. Metal-metal bonding correlations were analyzed using the empirical Pauling bond order concept.

Energy Technology Data Exchange (ETDEWEB)

Studies were conducted of the bifunctional oxygen electrode. The development of a rechargeable metal-oxygen (air) cell has been hampered to a great extent by the lack of a stable and cost effective oxygen electrode capable of use during both charge and discharge. The first type of bifunctional electrode consists of two distinct catalytifc layers. The oxygen reduction catalyst layer containing a supported gold catalyst is in contact with a hydrophilic nickel layer in which evolution of oxygen takes place. Loadings of gold from 0.5 to 1.0 mg/cm/sup 2/ were investigated; carbon, graphite, metal, and spinel oxides were evaluated as substrates. The second part of the research effort was centered on developing a reversible oxygen electrode containing only one catalytic layer for both reduction and evolution of oxygen. The work was directed specifically to the study of perovskite type of oxides with the composition AA/sup 1/BO/sub 3/ where A is an ...

Science.gov (United States)

Not Available

Science.gov (United States)

Feb 25, 2008 ... NASA's Visible Earth catalog of NASA images and animations of our home planet.

Energy Technology Data Exchange (ETDEWEB)

The magnetic ordering temperature of some rare-earth-based heavy-fermion compounds is strongly pressure dependent and can be completely suppressed at a critical pressure, p{sub c}, making way for novel correlated electron states close to this quantum critical point. We have studied the clean heavy-fermion antiferromagnets CePd{sub 2}Si{sub 2} and CeIn{sub 3} in a series of resistivity measurements at high pressures up to 3.2 GPa and down to temperatures in the mK region. In both materials, superconductivity appears in a small window of a few tenths of a GPa on either side of p{sub c}. We present detailed measurements of the superconducting and magnetic temperature-pressure phase diagram, which indicate that superconductivity in these materials is enhanced, rather than suppressed, by the closeness to magnetic order. (author)

International Nuclear Information System (INIS)

The ternary rare earth compound NdRh_4B_4 has been studied by means of critical field, low temperature heat capacity, and static magnetic susceptibility measurements. Features in the upper critical field and heat capacity data at 1.31 K and 0.89 K suggest the occurrence of long-range magnetic order in the superconducting state. The temperature dependence of the static magnetic susceptibility follows a Curie-Weiss law with an effective magnetic moment #mu#sub(eff) = 3.58 +- 0.05 #mu#sub(B) and a Curie-Weiss temperature thetasub(p) = -6.2 +- 1.0 K between 20 K and room temperature. However, magnetization vs. applied magnetic field isotherms suggest the development of a ferromagnetic component in the Nd"3"+ magnetization at low temperatures. (author).

Energy Technology Data Exchange (ETDEWEB)

The partial oxidation of 1,3-butadiene has been investigated over VMoO catalysts synthesized by sol-gel techniques. Surface areas were 9-14 m{sup 2}/g, and compositions were within the solid solution regime, i.e. below 15.0 mol % MoO{sub 3}/(MoO{sub 3} + V{sub 2}O{sub 5}). Laser Raman Spectroscopy and XRD data indicated that solid solutions were formed, and pre- and post-reaction XPS data indicated that catalyst surfaces contained some V{sup +4} and were further reduced in 1,3-butadiene oxidation. A reaction pathway for 1,3-butadiene partial oxidation to maleic anhydride was shown to involve intermediates such as 3,4-epoxy-1-butene, crotonaldehyde, furan, and 2-butene-1,4-dial. The addition of water to the reaction stream substantially increased catalyst activity and improved selectivity to crotonaldehyde and furan at specific reaction temperatures. At higher water addition concentrations, furan selectivity increased from ...

Energy Technology Data Exchange (ETDEWEB)

Very high cobalt catalysts have been prepared on steamed and acid-washed y zeolite. These catalysts are very active. Some of them have proven to be very stable. Additionally, if provisions are made to control the temperature build up on the catalyst bed, low methane selectivities result. Additional work is indicated, for instance, perhaps even higher activity catalysts can result from higher levels of cobalt or changes in the catalyst preparation procedure. Since the issue of whether small amounts of ruthenium can promote the catalyst is not completely resolved, catalyst preparation procedure experiments should continue with ruthenium vs. ruthenium-free catalysts. For instance, different methods of impregnation and/or activation should be investigated.

Energy Technology Data Exchange (ETDEWEB)

A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with a dihydrogen phosphate anion or a dihydrogen phosphite anion. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.

Energy Technology Data Exchange (ETDEWEB)

The reverse micelle catalyst preparation method has been used to prepare catalysts on four supports: magnesium oxide, carbon, alumina- titania and steamed Y zeolite. These catalysts were not as active as a reference catalyst prepared during previous contracts to Union Carbide Corp. This catalyst was supported on steamed Y zerolite support and was impregnated by a pore-filling method using a nonaqueous solvent. Additional catalysts were prepared via pore- filling impregnation of steamed Y zeolites. These catalysts had levels of cobalt two to three and a half times as high as the original Union Carbide catalyst. On a catalyst volume basis they were much more active than the previous catalyst; on an atom by atom basis the cobalt was about of the same activity, i.e., the high cobalt ...

International Nuclear Information System (INIS)

We present first-time measurements of the Fermi surface and low-energy electronic structure of intermetallic compounds Gd_2PdSi_3 and Tb_2PdSi_3 by means of angle-resolved photoelectron spectroscopy (ARPES). We show that the Fermi surface in both compounds consists of an electron barrel at the #GAMMA# point surrounded by spindle-shaped electron pockets originating from the same band, with the band bottom of both features lying at 0.5 eV below the Fermi level. From the experimentally measured band structure, we estimate the momentum-dependent RKKY coupling strength and demonstrate that it is peaked at the 1/2#GAMMA# K wave vector. Comparison with neutron diffraction data from the same crystals shows perfect agreement of this vector with the propagation vector of the low-temperature in-plane magnetic order, thereby demonstrating the decisive role of the Fermi surface geometry in explaining the complex magnetically ordered ground state of ternary ...

Energy Technology Data Exchange (ETDEWEB)

The rare-earth based nickelates RNiO{sub 3} (R=Pr, Nd, Sm, Eu, and Pr{sub 1-x}La{sub x}, 0{<=}x{<=}0.7) were studied by inelastic neutron scattering. Energy splittings due to the crystalline-electric-field (CEF) interaction at the R{sup 3+} site within the electronic ground-state J multiplet (for R=Pr, Nd, and Pr{sub 1-x}La{sub x}) as well as within the two lowest-lying J multiplets (for R=Sm and Eu) were directly observed, and the corresponding CEF energy-level schemes were reconstructed. The latter were rationalized in terms of CEF parameters, which vary smoothly over the rare-earth series and give magnetic properties associated with the R sublattice in agreement with results from neutron powder diffraction experiments. Across the metal-insulator transition, a continuous change in the electronic part of the CEF parameters is observed. However, an attempt to quantify a charge transfer from the observed variation of the CEF ...

Energy Technology Data Exchange (ETDEWEB)

Coal liquefaction investigations required the availability of model compounds for mechanistic investigations. Towards this end, IITRI was funded to develop an approach for the synthesis of one of the target compound. This study was carried out in several phases as outlined here. Initial synthetic investigations on obtaining 2-tetrolol was carried out using high pressure and temperature reduction with Raney nickel catalyst. The next step consisted in incorporation of a hydroxymethyelene group at the C-3 position. This was successfully carried out utilizing 2-tetrolol, formaldehyde, and calcium oxide. An alternate improved method was developed using 3-carboxyl-2-naphthol. This required less time, gave a cheer product in higher yield. Efforts at the introduction of a chloromethylene group only yielded polymeric material or starting material in spite of protection the phenolic group by various groups. They synthesis of 3, ...

Energy Technology Data Exchange (ETDEWEB)

In order to replace industrial cobalt and nickel and molybdenum catalysts, more economical catalysts, red muds, are used. Comparative data about the chemical, structural and thermal properties of different samples of red muds, which are important for catalytic hydrogenation, are cited. The different conditions for hydrogenation of coals in a reactor are examined.

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.

Energy Technology Data Exchange (ETDEWEB)

Investigations of alternative renewable energy resources continue, with many studies concentrating on hydrogen storage. However, there are a few problems such as storage, transportation, delivery to the user and usage safely, to be addressed to facilitate commercialization and wide usage of the hydrogen. The absorbed form within the metal hydrides seems to be the best solution of this problem. Since Li is the lightest metal, it has the advantage as the stored amount of hydrogen mass ratio. LiBH{sub 4} production process was investigated using elemental Li, B and H{sub 2}. Spex type ball milling with tungsten carbide, stainless steel and zirconia type vessels, was used to mix the different amount of Li and B under argon atmosphere. X-ray diffraction pattern demonstrated that the LiB was obtained. A system was designed to provide a hydrogen atmosphere of 60 bars to force hydrogen into the LiB structure. FTIR analysis strongly indicated the LiBH{sub 4} compound when ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

This report describes results from emissions testing of a prototype diesel engine, developed by Volvo Truck Corporation of Sweden, which uses pilot injection of diesel fuel for compression ignition of alcohol fuel injection for main combustion. In addition to this dual-fuel engine, emission testing was also conducted on a heavy-duty diesel engine of similar design. Both engines were tested over the 1979 13-mode FTP, or shorter versions of this modal test, and over the 1984 Transient FTP as well as an experimental bus cycle. The dual-fuel engine was characterized with methanol, ethanol and ethanol with 30 percent water (wt %). An oxidation catalyst was also used with methanol and ethanol. Emission characterization included regulated emissions (HC, CO, and NOX) along with total particulate, unburned alcohols, individual hydrocarbons, aldehydes, phenols, and odor. The particulate matter was characterized in terms of particle size distribution, sulfate content, C, H, ...

Energy Technology Data Exchange (ETDEWEB)

Ex situ and in situ fuel cell degradation of a sPAEK membrane were investigated. Post-mortem analyses of the aged membrane and of the degradation products eluted in water were carried out by NMR, IR, SEC and EDX. Ex situ agings were performed in a low concentration H{sub 2}O{sub 2} solution (0.07%) without any metallic catalyst. We exemplify that ex situ accelerated aging tests in such hydrogen peroxide solution are relevant to the chemical degradation in fuel cell. We have shown that a 500 h fuel cell test at moderate temperature (60 C) induces significant modifications on the macromolecules such as a 40% molecular weight reduction. Degradation appears heterogeneous and limited to the cathode side. The model compound approach developed in the previous article (Perrot et al.) has allowed the identification of the aging path in fuel cell. Phenolic and carboxylic acid chain ends have been identified as the main products resulting from polymer ...

Energy Technology Data Exchange (ETDEWEB)

Red mud is a by-product of bauxite processing through Bayer process. The amount of red mud generated depends largely on the type of ore used and the processing. Use of red mud as a catalyst can be a good alternative to the existing commercial catalysts. Its properties such as iron content in form of ferric oxide (Fe{sub 2}O{sub 3}), high surface area, sintering resistance, resistance to poisoning and low cost make it an attractive potential catalyst for many reactions. Besides red mud, ferric ion sludge from wastewater treatment plant has also been studied for its catalytic properties, mainly due to its ferric oxide constituent. This paper reviews the studies on red mud as a catalyst. The catalyst characteristics, reaction mechanisms involved and performance are examined and compared with iron oxide catalyst and commercial catalysts. ...

Energy Technology Data Exchange (ETDEWEB)

The research has involved the characterization of catalyst acidity, [sup 2]D NMR studies of Bronsted acid sites, and kinetic, calorimetric, and spectroscopic studies of methylamine synthesis and related reactions over acid catalysts. Approach of this work was to explore quantitative correlations between factors that control the generation, type, strength, and catalytic properties of acid sites on zeolite catalysts. Microcalorimetry, thermogravimetric analysis, IR spectroscopy, and NMR spectroscopy have provided information about the nature and strength of acid sites in zeolites. This was vital in understanding the catalytic cycles involved in methylamine synthesis and related reactions over zeolite catalysts.

Energy Technology Data Exchange (ETDEWEB)

Pt-based ternary catalysts have been proposed as electrode materials for low temperature fuel cells. Pt-Ru-based ternary catalysts were tested as anode materials with improved CO tolerance or enhanced activity for methanol or ethanol oxidation. Ternary catalysts based on platinum alloyed with first row transition metals were tested as cathode materials with improved activity for the oxygen reduction. This paper presents an overview of the preparation methods and structural characteristics of these ternary catalysts. (author)

Science.gov (United States)

Feb 25, 2008 ... In the two Landsat scenes shown above, the pattern of deforestation can be clearly discerned. Deep green in these images shows lush ...

Science.gov (United States)

films and cylinders of rare earth doped yttrium aluminum garnets. ... We knew that yttrium aluminum garnet (YAG) could be doped with ...

Science.gov (United States)

... of this material is, however, outside the currently approved earth fill materials collection area ... fill material suitable for its intended use. The currently approved site contains material that is ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes the vapor phase catalytic dehydrogenation of a C/sub 2/-C/sub 4/ paraffin by contacting the paraffin with a spinel of the formula A/sup III/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/, formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/, formula (2) where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is oone of more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to < 1.9, and y is zero to < 0.9, which spinel or perovskite is made by a process which comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup 111/ state by heating at 100/sup 0/C or less an aqueous medium slurry of solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium ether before, during or after the ...

International Nuclear Information System (INIS)

Various compositions of Y(Ta,Nb)O4:Eu3+,Tb3+ with different Nb and activator concentrations have been investigated under UV and VUV excitation. Some compounds with very strong emission under VUV excitation were found. Such phosphors could be proposed as very good emissive materials for Displays and Lightings. The growing interest in luminescence spectroscopy of rare earth ions in the vacuum ultraviolet (VUV) and the visible (VIS) spectral range is due to industrial demands for new applications. YTaO4 and YNbO4 phosphors are a perspective class of efficient materials that are generally used in X-ray intensifying screens. These phosphors exhibit satisfying luminescence whenever excited by UV light, cathode radiation or X ray. However, to our knowledge, no work has been published on the VUV-excited luminescence for Eu3+ and Tb3+ double activated yttrium niobate and yttrium tantalate based phosphors. In this paper, the VUV-UV PL and PLE spectra of ...

International Nuclear Information System (INIS)

The series of cubic pyrochlore structure compounds, R_2Mo_2O_7 (R = Nd-Yb, Y; R not= Eu), were prepared as single phase materials by solid state reaction between R_2O_3 and MoO_2 at 1400 "0C in a CO/CO_2 = 1 buffer gas atmosphere. Lattice constants obtained from X-ray powder data compare well with results from previous studies. Magnetic susceptibility and magnetization data were obtained for all samples between 300 K and 4.2 K (700 K for R = Gd) and a range of applied fields. For R = Nd, Sm, and Gd magnetic ordering is observed at 97 K, 93 K and 83 K respectively which is assigned to ferromagnetism on the Mo(IV) sublattice. The Mo(IV) moment in the ordered state is about 1 #mu#/sub B/. At low temperatures, the Gd(III) and Mo(IV) moments are apparently coupled feromagnetically in Gd_2Mo_2O_7 yet the high temperature susceptibility data seem to indicate a ferrimagnetic (antiparallel) Gd(III)-Mo(IV) coupling. The low-temperature magnetic properties of Nd_2Mo_2O_7 and ...

Science.gov (United States)

Description of how global warming could be disastrous for much of the earth's population....

ScienceCinema

...global warming situation is more than evaporation around ...background red ? which was the global warming the ...

International Nuclear Information System (INIS)

FT-IR spectra of the products obtained in each step of the tetramethyltin (TMT)/3-wt.% Re_2O_7/Al_2O_3-SiO_2 and TMT/Al_2O_3-SiO_2 system preparation are presented and discussed. The obtained spectra show that TMT reacts with alumina-silica hydroxyl groups already at room temperature, yielding surface methyltin compounds; NH_4ReO_4 reacts with alumina-silica surface at temperatures up to 423 K, yielding rhenium surface species and ammonia, which is strongly bonded by acidic sites of the Broensted kind. FT-IR spectrum of the system (TMT)/3-wt.% Re_2O_7/Al_2O_3-SiO_2 indicated the absence of surface methyl tin compounds observed on the surface system TMT/Al_2O_3-SiO_2 , and the presence of physically adsorbed TMT; after 5 h of evacuation of the TMT/3-wt.% Re_2O_7/Al_2O_3-SiO_2 system, the FT-IR spectrum indicated the presence of only a single band at 2977 cm"-"1, which may be assigned to the C-H bond stretching of the methyl group in the surface ...

British Library Electronic Table of Contents (United Kingdom)

Co catalysts, obtained from a layered double Co?Zn?Al hydroxide, are highly active and stable towards the hydrogenolysis of glycerol to 1,2-propanediol (1,2-PDO) in aqueous media. The Co-673 catalyst, containing a CoO species, provided a glycerol conversion of 67.7% and a 1,2-PDO selectivity of 50.5%. The Co-873 catalyst comprising 16?nm Co nanoparticles gave a glycerol conversion of 70.6% and a 1,2-PDO selectivity of 57.8%. It was revealed that the CoO species in the Co-673 catalyst was readily converted to 50?nm Co particles under the glycerol hydrogenolysis conditions. The Co catalysts maintained a stable size and phase in recycling tests. Graphical Abstract

British Library Electronic Table of Contents (United Kingdom)

Catalyst deactivation during steam reforming of transportation fuels, primarily due to sulfur poisoning and carbon deposition, is a major hurdle in the commercialization of fuel cell technologies. In an attempt to better understand the phenomena, a previously formulated multi-component (Ni, Pd, Rh) catalyst supported on g-Al2O3 was studied under steam reforming of Jet A spiked with thiophene to achieve a total sulfur content of 1000ppm by weight. Analysis of fresh catalysts showed the presence of two groups of active metal particles, primarily distinguished by their size and composition; small particles (1-5nm) largely comprised of Rh and large particles (10-20nm) that were predominantly Ni, with or without the presence of Pd. Analysis of used catalysts showed sintering of crystallites con...

Energy Technology Data Exchange (ETDEWEB)

This work studied the effect of the nature of the metal on the performance of Co/CeO{sub 2}, Pd/CeO{sub 2} and Pt/CeO{sub 2} catalysts in the partial oxidation of ethanol. Infrared spectroscopy of adsorbed ethanol and temperature programmed desorption of ethanol were performed in order to establish the reaction mechanism. Catalytic experiments revealed that the product distribution is strongly affected by the nature of the metal. Acetaldehyde was practically the only product formed on a Co/CeO{sub 2} catalyst while methane was also produced on Pt/CeO{sub 2} and Pd/CeO{sub 2} catalysts. These results were explained through a reaction mechanism proposed by the characterization techniques. Co/CeO{sub 2} and Pt/CeO{sub 2} catalysts show mainly ethoxy species at room temperature whereas acetate species is mainly formed on the Pd/CeO{sub 2} catalyst. The ethoxy species can undergo further ...

Science.gov (United States)

The oxidative dehydrogenation (OXDH) of n-butane, 1-butene, and trans-2-butene on different vanadia catalysts has been compared. MgO, alumina, and Mg-Al mixed oxides with Mg/(Al + Mg) ratios of 0.25 and 0.75 were used as supports. The catalytic data indicate that the higher the acid character of catalysts the lower is both the selectivity to C{sub 4}-olefins from n-butane and the selectivity to butadiene from both 1-butene or trans-2-butene. Thus, OXDH reactions are mainly observed from n-butane and butenes on basic catalysts. The different catalytic performance of both types of catalysts is a consequence of the isomerization of olefins on acid sites, which appears to be a competitive reaction with the selective way, i.e., the oxydehydrogenation process by a redox mechanism. Infrared spectroscopy data of 1-butene adsorbed on supported vanadium oxide catalysts suggest the presence of ...

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this research work was to prepare hydrocracking catalysts using amorphous silica-alumina (ASA) supports in combination with USY and {beta}-zeolites. Three supports: namely silica-alumina, USY and {beta}-zeolites were selected to prepare the extrudates using AP-1 as a binder, while two metal pairs: namely Ni-W and Ni-Mo were loaded on the extrudates through co-impregnation using incipient wetness technique. The catalysts were then calcined at 550C for 2h. The catalysts were tested in a fixed-bed flow reaction system for their activity, using desulfurized vacuum gas oil (DS-VGO) as a feedstock. The catalytic evaluation results of the catalysts showed that {beta}-zeolite alone and in combination with the ASA used in this study, has a potential as a support for developing heavy oil hydrocracking catalysts. A balance of weak and strong acidities of {beta}-zeolite ...

Energy Technology Data Exchange (ETDEWEB)

A process is claimed for selectively preparing alpha-olefins having from 2 to about 22 carbon atoms by contacting a gaseous mixture containing carbon monoxide and hydrogen with an iron titanate alkali metal hydroxide catalyst at reaction conditions correlated so as to favor the formation of a substantial proportion of such alpha-olefin product.

Science.gov (United States)

The title compounds were prepared by arc-melting of the elemental components. Whereas NdPdSi and SmPdSi are already present after the arc-melting, alpha-GdPdSi and alpha-TbPdSi are formed only during the annealing at 800 degC. The four compounds crystallize with the recently reported alpha-YbAuGe type structure, which was refined for alpha-GdPdSi: Pnma, a=2108.0(4) pm, b=433.9(1) pm, c=745.6(1) pm, Z=12, R=0.026 for 1447 structure factors and 62 variable parameters. The lanthanoid atoms are situated between two-dimensionally infinite nets of condensed, puckered hexagons formed by alternating palladium and silicon atoms, with Pd-Si distances varying between 251 and 262 pm. In the third dimension these nets are linked via weak Pd-Pd (300 pm), Pd-Si (283 pm), and Si-Si bonds (261 pm). The refinements of the occupancy parameters suggested that ca. 2% of the palladium sites are occupied by silicon atoms and vice versa. The structural relationships ...

Energy Technology Data Exchange (ETDEWEB)

Substitution of various rare earths R within the class of R2PdSi3 single crystals with hexagonal AlB2-type crystallographic structure reveals the systematic dependence of anisotropic magnetic properties governed by the interplay of crystal-electric field effects and magnetic two-ion interactions. Here we compare the floating zone (FZ) crystal growth with radiation heating of compounds with R = Tb, Tm, Pr, and Gd. The congruent melting behavior enabled moderate growth velocities of 3 to 5 mmh-1. The preferred growth directions are close to the basal plane of the hexagonal unit cell. The composition of the crystals, except of Tb2PdSi3, is slightly Pd-depleted with respect to the nominal composition 16.7 at.% Pd. Thin precipitates of RSi secondary phases were detected in the crystal matrix. Their phase fraction can be diminished by growth from Pd-rich melt compositions and annealing treatments. The compounds exhibit ...

Energy Technology Data Exchange (ETDEWEB)

Reinforced (heterogel) silicate materials containing an amorphous and a crystalline phase are being used more and more industry. Such systems are energetically unsaturated and therefore promising for use in catalysts. The authors used two reinforced materials as supports: an aluminosilicate containing a zeolite (the cracking catalyst, tseokar) and asbestos-containing aluminosilicate. The active component was introduced by impregnation, and this was followed by heat treatment during which the chemical composition and porous structure were formed. The impregnating mixture consisted of solutions of potassium sulfate and vanadate of the required concentrations. The testing shows that reinforced heterogel systems are promising as support materials for sulfuric acid catalysts.

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Promoted antimony phosphate oxide complexes are excellent catalysts for the ammoxidation of methanol to HCN especially at high methanol throughputs.

Energy Technology Data Exchange (ETDEWEB)

The oxidation of sulfur dioxide in gas diffusion electrodes (GDE) in the presence of a homogeneous catalyst, potassium iodide, is investigated. The influence of this catalyst on the voltage-current (V-I) characteristics of the electrodes and the utilization of sulfur dioxide is determined. It is shown that when using the homogeneous catalyst potassium iodide, the utilization can reach 95-100%.

Science.gov (United States)

... PADS(CUSHIONS), OBTURATION(BALLISTICS), BUTYL RUBBER, COMBUSTIBLE CARTRIDGE CASES, PHOSPHORUS COMPOUNDS. ...

Energy Technology Data Exchange (ETDEWEB)

Several kinds of catalysts for coal liquefaction were analysed by means of high pressure differential thermal analysis (DTA). The activity order is as follows: Fe(OH)/sub 3/.Ni(OH)/sub 2/ > 3665 > Fe(OH)/sub 3/.MoO/sub 3/ > Jin Chuan Mineral > concentrated pyrite > Japan red-mud approx. equal to Fe(OH)/sub 3/.CuO approx. equal to no catalyst. If the catalysts are promoted by sulphur., the activity order is 3665 + S > Fe(OH)/sub 3/.Ni(OH)/sub 2/ + S > Fe(OH)O/sub 33/ + S > Japan red mud + S > Fe(OH)O/sub 3/.CuO + S > no catalyst. The kinetic parameters of three catalysts commonly used in the liquefaction of coal were determined.

Science.gov (United States)

This quarterly report, for the period April 1-June 30, 1982, summarizes Sandia's activities in coal liquefaction process research. The overall objectives of the program are to understand the mechanisms and determine the role of catalysts in the direct conversion of coal to liquids. Primary emphasis is being given to the Integrated Two-Stage Liquefaction (ITSL) process. Specific tasks include: short-contact time coal liquefaction, mineral matter effects and catalyst studies. During this period, work was done on: the characteristics of a Liquefaction (ITSL) facility at New Brunswick, NJ; the kinetics of hydrogenation and dehydrogenation of pyrene and dihydropyrenes in batch microreactors; the impact of coal cleaning on the effectiveness of two types of slurry phase catalysts; the deactivation of aged catalyst samples obtained from the H-Coal PDU; and a catalyst deactivation ...

Energy Technology Data Exchange (ETDEWEB)

The vast majority of fundamental studies of metal oxide selective oxidation catalysts have been performed with single phase systems. These investigations established the basic tenents of the redox mechanism of selective oxidation and ammoxidation catalysis. By comparison, structural and kinetic investigations of multiphase oxide catalysts are less numerous because of the inherent difficulties in understanding the relative contributions of separate phases to the catalytic behavior of the composite catalyst. Some attempts have been made in the past to understand the complex chemistry of multiphase catalysts and additional important insights have been realized more recently. However, a clear understanding of the most significant catalytic interactions between individual phases of a multiphase multicomponent redox catalyst is still lacking. In an effort to provide an understanding and a ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to test the catalytic oxidation of pyridine over zeolite-supported catalysts and to compare the difference in their activities for the oxidation of pyridine. The catalytic oxidation of pyridine pollutant on a series of copper-supported catalysts, inclusive of Cu/beta, Cu/ZSM-5, Cu/MCM-41 and Cu/{gamma}-Al{sub 2}O{sub 3}, in the presence of excess oxygen was studied. The activity of the copper-supported catalysts for the pyridine oxidation could be correlated with the binding energy of oxygen coordinated to metal copper, while the ability to control the yield of NO{sub x} appeared to be strongly dependent on the binding energy of NO bonded to metal copper. On these catalysts, two copper species, Cu(H{sub 2}O){sub 6}{sup 2+} ions and CuO were identified, in which Cu{sup 2+} ions had higher activity for the NO{sub x} control but poorer activity for the pyridine oxidation. Amongst ...

Energy Technology Data Exchange (ETDEWEB)

Influence of residual K{sup +} on the preferential oxidation of CO in excess hydrogen (PROX) over CuO-CeO{sub 2} catalysts was investigated. CuO-CeO{sub 2} catalysts were characterized by BET, ICP, XRD, UV-Raman and TPR techniques. The results showed that the existence of residual K{sup +} made {alpha} peak in TPR of CuO-CeO{sub 2} catalysts shift to higher temperatures and depressed the PROX in the absence of CO{sub 2} and H{sub 2}O in the feed over CuO-CeO{sub 2} catalysts. However, small amount of residual K{sup +} was beneficial to the catalytic performance of CuO-CeO{sub 2} catalysts in the PROX in the presence of CO{sub 2} and H{sub 2}O in the feed. Consequently, residual K{sup +} with an appropriate content was beneficial to improve the catalytic performance of CuO-CeO{sub 2} catalysts in the presence of CO{sub 2} and H{sub 2}O. (author)

Science.gov (United States)

of satellite, aircraft and ground-based observations. In ..... swarm traps by Utah Department of Food and Agriculture (DAF) personnel. Preliminary Results ..... the 150th anniversary of the book's publication and the 200th anniversary of Darwin's birth. ...... cold war submarine missions to find that Arctic Ocean ...

Energy Technology Data Exchange (ETDEWEB)

Rare Earth Cobalt (REC) permanent magnets have unique properties that permit solutions to some optical tasks that cannot be accomplished with conventional magnets. A review of design and of performance characteristics of these magnets includes an analytical description of the three dimensional fringe fields of REC quadrupoles.

Science.gov (United States)

(Like using solar cookers to make hot dogs! Yummm!) How many people do you want to attend? 5? 30? 200?!? (Ambitious aren't we?) ...

Science.gov (United States)

The Grover S and X-band dual-wavelength radar system has been ...... A. H. Watkins (U.S. Geological Survey, Earth Resources. Observation Systems Data Center ...

International Nuclear Information System (INIS)

The prospect for the recovery of rare earths from red mud, the bauxite tailings from the production of alumina is examined. The Jamaican red mud by far has the higher trace concentrations of lanthanum, cerium, neodymium, and yttrium. Scandium is also present. The dissolution of the rare earth is a major extraction problem because of the large volume of other materials. The recovery processes that have been proposed include the production of co-products such as iron, alumina, and titanium concentrates, with the rare earths going with the titanium. In this paper a critical examination of the possible processes are presented with the recommended research projects to be carried out.

National Aeronautics and Space Administration (NASA)

NASA's Glory spacecraft is equipped to survey and map aerosols in Earth's atmosphere during a mission marking the return to flight of the Taurus XL rocket.

CERN Document Server

We calculated the matter effect, including both the Earth and supernova, on the detection of neutrinos from type II supernovae at the proposed Daya Bay reactor neutrino experiment. It is found that apart from the dependence on the flip probability P_H inside the supernova and the mass hierarchy of neutrinos, the amount of the Earth matter effect depends on the direction of the incoming supernova neutrinos, and reaches the biggest value when the incident angle of neutrinos is around 93^\\circ. In the reaction channel \\bar{\

Energy Technology Data Exchange (ETDEWEB)

We examined a catalytic effect of niobium oxide (Nb{sub 2}O{sub 5}) on the hydrogen storage properties of MgH{sub 2} prepared by mechanical ball milling method. The MgH{sub 2} composite doped with 1 mol% Nb{sub 2}O{sub 5} by ball milling for 20 h desorbed hydrogen up to {approx}6 mass% in the temperature range from 200 to 250 {sup o}C at the heating rate of 5 {sup o}C/min under a purified helium flow. After dehydrogenation at 200 {sup o}C, the product showed remarkable hydrogen absorption kinetics. A large amount of gaseous hydrogen up to {approx}4.5 mass% was absorbed even at room temperature under 1 MPa hydrogen pressure within 15 s and finally its capacity reached up to 5 mass%. Furthermore, the valence state of Nb{sub 2}O{sub 5} doped in MgH{sub 2} was examined by X-ray absorption near edge structure (XANES) measurement. The results indicated that additive Nb{sub 2}O{sub 5} was reduced by MgH{sub 2} during mechanical milling. This suggests that the Nb compound, ...

Energy Technology Data Exchange (ETDEWEB)

The catalytic nature of Mo(CO)/sub 6/ supported on ..gamma..-Al/sub 2/O/sub 3/, KOH-doped ..gamma..-Al/sub 2/O/sub 3/, and HY-zeolite was investigated in CO oxidation with N/sub 2/O in comparison with that of a conventional partially reduced MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst. Kinetic parameters of this reaction were obtained in the range 0 to 100/sup 0/C; the rate law r = kP/sub N/sub 2/O//sup 1/P/sub CO//sup 0/ was found on all catalysts, and the activation energy was estimated to be 9.1 kcal/mol on the Mo(CO)/sub 6/-derived catalysts and 7.1 kcal/mol on the partially reduced MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst. Maximum catalytic activities were obtained by activating the Mo(CO)/sub 6/-derived catalysts at 400/sup 0/C. To obtain similar activity on the MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst, it was necessary to reduce at ...

CERN Document Server

The possible physical linkage between galactic cosmic rays intensity and the Earth's cloud cover is discussed using the analysis of the first indirect aerosol effect (Twomey effect) and its experimental representation as the dependence of average cloud droplet effective radius on aerosol index characterizing the aerosol concentration in the atmospheric air column of unit section. It is shown that the basic kinetic equation of the Earth's climate energy-balance model is described by the bifurcation equation (with respect to the temperature of the Earth's surface) in the form of fold catastrophe with two governing parameters defining the variations of insolation and Earth's magnetic field (or galactic cosmic rays intensity in the atmosphere), respectively. The principle of hierarchical climatic models construction, which consists in the structural invariance of balance equations of these models evolving ...

Energy Technology Data Exchange (ETDEWEB)

Chloromethane, dichloromethane and 1,2-dichloroethane were completely decomposed in air on perovskite-type catalysts (LaMnO{sub 3}, LaCoO{sub 3}, (La{sub 0.84},Sr{sub 0.16})(Mn{sub 0.67},Co{sub 0.33})O{sub 3}) at reaction temperatures above 550C. Besides the main reaction products (carbon dioxide, water and hydrochloric acid), by-products (higher chlorinated-, C-C coupling- and cracking products) were formed in the low temperature range. Depending on the reaction temperature, residence time and kind of chlorinated hydrocarbon a reversible catalyst deactivation takes place. In the case of LaCoO{sub 3} catalysts an irreversible deactivation was observed. X-ray diffraction (XRD) and electron probe microanalysis (EPMA) measurements with the perovskite-type catalysts after interaction of chlorinated hydrocarbons indicate the formation of chlorinated species on the catalyst surface and in ...

International Nuclear Information System (INIS)

Proton exchange membrane fuel cells (PEMFCs) are attractive because of their high conversion efficiency, low pollution, lightweight, and high power density. A major area of challenges is the design and engineering of active, robust, and low-cost electrocatalysts. This report discusses recent findings of our investigations of the design and nano-engineering of platinum-vanadium-iron catalysts for use in PEMFC. The membrane electrode assembly was prepared using nano-engineered PtVFe nanoparticles with controlled composition and size supported on carbon as cathode electrocatalysts. The electrocatalytic activity and stability of the catalysts have been characterized by both rotating disk electrode and membrane electrode assembly measurements. The trimetallic catalysts have been shown to exhibit excellent electrocatalytic performance in PEMFC in comparison with commercial platinum catalysts. The results ...

Energy Technology Data Exchange (ETDEWEB)

Special CoMo/Al{sub 2}O{sub 3} catalysts were prepared for testing in coal liquefaction: a conventional CoMo/Al{sub 2}O{sub 3} catalyst, one containing Zn as a second promoter and one having the alumina acidified with fluorine. Their activities were compared with that of red mud. The experiments were conducted in a stirred autoclave with a subbituminous coal and solvent (tetralin, anthracene oil or creosote oil) at 425{degree}C and 17 MPa. The liquefaction products were fractionated into oils, asphaltenes and preasphaltenes with pentane, toluene and THF. The Co(Zn)Mo/Al{sub 2}O{sub 3} catalysts have far higher activities than red mud. Zn and fluorine have beneficial effects on the catalyst activity. Coal tar distillates give higher conversions and oil + gas yields than tetralin when the prepared catalysts are used. 17 refs., 7 tabs.

Science.gov (United States)

Recently there has been considerable interest in the Cu-ZSM-5 catalysts for the selective reduction of NO by light hydrocarbons for the purpose of atmospheric pollution abatement. Isobutane and n-pentane cracking were studied over Cu zeolite catalysts and these results were compared with their HY analogues at low conversions and at temperatures of 673 K and below. Three forms of the catalysts were used: those reduced in CO at 773 K; those reduced with H[sub 2] at 473 K; and those in the oxidic form (following flushing with He at 773 K). In contrast with an earlier publication, very little difference in activity was found between the two reduced forms of the catalysts did not differ significantly from each other nor from the H-form of the zeolite. They are typical of a Bronsted acid catalysis. The oxidic form of the catalyst produced excess H[sub 2] in increasing amounts with time on ...

International Nuclear Information System (INIS)

Uranium dendrites which were deposited at a solid cathode of an electrorefiner contained a certain amount of salts. These salts should be removed for the recovery of pure metal using a cathode processor. In the uranium deposits from the electrorefining process, there are actinide chlorides and rare earth chlorides in addition to uranium chloride in the LiCl-KCl eutectic salt. The evaporation behaviors of the actinides and rare earth chlorides in the salts should be investigated for the removal of salts in the deposits. Experiments on the salt evaporation of rare earth chlorides in a LiCl-KCl eutectic salt were carried out. Though the vapor pressures of the rare earth chlorides were lower than those of the LiCl and KCl, the rare earth chlorides were co-evaporized with the LiCl-KCl eutectic salt. The Hertz-Langmuir relation was applied for this evaporation, and also the evaporation ...

Energy Technology Data Exchange (ETDEWEB)

The batchwise preparation of molecular sieves for methanol conversion shows some inconsistency in catalytic stability. This is a result mainly of the change of SiO/SUB/2/Al/SUB/2O/SUB/3 in ion exchange to an H-type sieve. The dealumination during ion exchange depends upon crystal size and structural factors, which can be characterised by the cyclohexane adsorption of the raw molecular sieve. A high SiO/SUB/2/Al/SUB/2O/SUB/3 H-molecular sieve can be prepared from a molecular sieve of high adsorption capacity, this leading to a catalyst of higher stability. (4 refs.)

British Library Electronic Table of Contents (United Kingdom)

Palladium silicide was formed on the sol-gel derived SiO2 supported Pd catalysts prepared by ion-exchange method (Pd/SiO2-SG-ion). However, the catalysts exhibited superior performances than commercial SiO2 supported ones in liquid-phase semihydrogenation of phenylacetylene. It was probably due to an inhibition of a product of styrene, which is adsorbed on the surface of Pd, more strongly on Pd/SiO2-SG in which Pd is electron-deficient as shown by larger binding energy from XPS results.

British Library Electronic Table of Contents (United Kingdom)

One-pot multi-component condensation of benzyl, aldehydes, ammonium acetate and primary amines were used for synthesis of 2,4,5-trisubstituted and 1,2,4,5-tetrasubstituted-1H-imidazole derivatives under MW radiation using amberlyst A-15 as a catalysts. This catalyst has several advantages (simple work-up, low cost and reusability).

British Library Electronic Table of Contents (United Kingdom)

It was demonstrated that R 2?R 4 saturated monohydric alcohols can be synthesized from CO and H2 in the presence of Fe catalysts containing a carbon support of the Sibunit type with granule sizes of 3?5, 1?2, and 0.05?0.1 mm in a fixed-bed reactor at 3 MPa and 240?300?C. It was found that the activity of Fe/Sibunit catalysts and their selectivity for the formation of liquid synthetic products increased with the size of granules and the amount of iron. The catalysts make it possible to obtain fatty alcohols, in which the fraction of R 2?R 4 alcohols is as high as 75%, in yields to 56 g/m3.

International Nuclear Information System (INIS)

Graphical abstract: - Abstract: Low loading platinum-cobalt (Pt-Co) cathode catalyst on a Nafion(Na+)-bonded carbon layer is fabricated by using galvanostatic pulse technique to show the advantage of electrodeposition for high utilization of catalyst in proton exchange membrane fuel cell (PEMFC). We observed that Pt-Co catalysts evenly exist on the surface of carbon electrode and its thickness is about 5.8 ?m, which is four times thinner than conventional Pt/C. Improved single cell power performance of Pt-Co cathode catalysts with a ratio of 3.2:1 compared with Pt/C is clearly presented.

Energy Technology Data Exchange (ETDEWEB)

The photocatalyzed degradation of pyridine in the gas phase was investigated using titanium dioxide semiconductor supported on mordenite. The complete mineralization was found to occur over a catalyst containing 75 wt% TiO{sub 2} and 25 wt% mordenite in about 180 min in the presence of saturated water vapor at O{degrees}C (4.6 Torr). Low water vapor pressure of 0.096 Torr was found to be sufficient to achieve a reasonably high percentage and rate of degradation. Diffusion of pyridine within the catalyst adversely affects the activity when the thickness of the catalyst coating exceeds the penetration depth of illumination. The activity of the zeolite-supported catalysts was higher than that of TiO{sub 2}. The photonic efficiency for the complete mineralization of pyridine to CO{sub 2} was determined to be 0.48. 29 refs., 6 refs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

A new method of the synthesis of high molecular polybutylene terephthalate (PBT) is developed with the use of Irganox 1010, tris(nonylphenyl) phosphite and hypophosphite as stabilizers and boron nitride or boron oxide as a catalyst is proposed.

Energy Technology Data Exchange (ETDEWEB)

Acrylonitrile is a versatile intermediate and is produced by the Sohio ammoxidation process world-wide at a level of 8 billion pounds per year. In the catalytic process, propylene, ammonia and air are converted to acrylonitrile directly. The most widely used catalysts are mixed metal molybdates or antimonates. The current investigation deals with metal tellurates as possible low temperature ammoxidation catalysts. Of the catalysts investigated, iron-selenium-tellurates are of particular interest since they exhibit good ammoxidation activity already at 320/sup 0/C which is about 100/sup 0/C lower than the temperature required for molybdate or antimonate systems. Mechanistically, the tellurates behave more similarly to the antimonates than the molybdates. 3 tabs., 4 figs., 13 refs.

International Nuclear Information System (INIS)

Isopropyl chloroacetate has been synthesized by esterification of chloroacetic acid and isopropanol, using lanthanum dodecyl sulfate (LDDS) as the catalyst. Various factors that affected the esterification have been investigated, such as reaction time, different water-carrying agent and the amount of catalyst. Under the condition of 1.2/1 molar ratio of isopropanol to chloroacetic acid, 1.0% catalyst (molar percent of chloroacetic acid), 2.5 h reaction time, 5 mL cyclohexane as water-carrying agent and reflux temperature, the esterification conversion of isopropyl chloroacetate reaches 98.3%. The catalytic activity of LDDS is almost equal to that of a Bronsted acid. LDDS, as one kind of water-tolerant Lewis acid, is an excellent catalyst compared to the traditional Lewis acid. (author)

Energy Technology Data Exchange (ETDEWEB)

Alkali metal doped double perovskites containing manganese and at least one of cobalt, iron and nickel are useful in the oxidative coupling of alkane to higher hydrocarbons.

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The mechanism of the IndolPhos-Rh-catalyzed asymmetric hydrogenation of prochiral olefins has been investigated by means of X-ray crystal structure determination, kinetic measurements, high-pressure NMR spectroscopy, and DFT calculations. The mechanistic study indicates that the reaction follows an unsaturate/dihydride mechanism according to Michaelis-Menten kinetics. A large value of KM (KM=5.01+-0.16 M) is obtained, which indicates that the Rh-solvate complex is the catalyst resting state, which has been observed by high-pressure NMR spectroscopy. DFT calculations on the substrate-catalyst complexes, which are undetectable by experimental means, suggest that the major substrate-catalyst complex leads to the product. Such a mechanism is in accordance with previous studies on the mechanism...

Science.gov (United States)

Not Available

Science.gov (United States)

Not Available

Indian Institute of Science Theses & Dissertations (India)

Full Text Available

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The heterogeneous solid catalyst, mercaptopropylsilica (MPS), has been prepared by a modified procedure in water and its structure confirmed by solid state carbon-13 CP-MAS NMR spectrum. This catalyst has been efficiently utilized for the synthesis of a wide variety of tri-, tetrasubstituted imidazoles and their bis-analogues at room temperature. The protocol was further explored for the synthesis of the drug trifenagrel.

Energy Technology Data Exchange (ETDEWEB)

In order to design catalysts suitable for primary liquefaction stage and secondary upgrading stage respectively in the multi-stage liquefaction process, various carbon-supported catalysts were prepared. Catalytic activities of them were investigated for the hydrogenation of 1-methylnaphthalene, to discuss the influences of metals and carbon species on the catalytic activity. Various water soluble and oil soluble Mo and Ni salts were used for NiMo supported catalysts. Among various carbon supports, Ketjen Black (KB) was effective for preparing the catalyst showing the most excellent hydrogenation activity. The KB and Black Pearl 2000 (BP2000) showing high hydrogenation activity were fine particles having high specific surface area more than 1000 m{sup 2}/g and primary particle diameter around 30 nm. This was inferred to contribute to the high dispersion support of active metals. Since such fine particles ...

Energy Technology Data Exchange (ETDEWEB)

On handling nitric solutions in the glove box nitrous gases are formed that are sucked off via a heated activated charcoal filter and a catalyst cartridge containing e.g. the FG 590 H catalist (Degussa). By the activated charcoal the nitrous gases are reduced to N/sub 2/ and CO gas; the catalyst will oxidize CO to CO/sub 2/. The CO/sub 2/ obtained is discharged through an exhaust air filter in the glove box.

Energy Technology Data Exchange (ETDEWEB)

CeO{sub 2}-TiO{sub 2} catalysts are prepared by coprecipitation method, and the activity and stability in the catalytic wet air oxidation (CWAO) of phenol are investigated in a batch reactor and packed-bed reactor. CeO{sub 2}-TiO{sub 2} mixed oxides show the higher activity than pure CeO{sub 2} and TiO{sub 2}, and CeO{sub 2}-TiO{sub 2} 1/1 catalyst displays the highest activity in the CWAO of phenol. In a batch reactor, COD and TOC removals are about 100% and 77% after 120 min in the CWAO of phenol over CeO{sub 2}-TiO{sub 2} 1/1 catalyst at reaction temperature of 150 {sup o}C, the total pressure of 3 MPa, phenol concentration of 1000 mg/L, and catalyst dosage of 4 g/L. In a packed-bed reactor using CeO{sub 2}-TiO{sub 2} 1/1 particle catalyst, over 91% COD and 80% TOC removals are obtained at the reaction temperature of 140 {sup o}C, the air total pressure of 3.5 MPa, the phenol ...

Energy Technology Data Exchange (ETDEWEB)

When the foundations of the building are designed and worked, the prediction calculation of immediate settlement of the building exercised practically is to calculate assuming the earth is a linear elastic body, but the actual stress-strain relationship of the earth is nonlinear and rigidity of the earth becomes lower as strain (or stress) increases. Hence in order to grasp the actual settling behavior of the earth, it is necessary to elucidate the nonlinear relationship between stress and strain. In this article, a prediction method of building settlement is introduced which uses an analytical technique of the multi-layered earth by the linear elasticity theory and takes into consideration strain dependency of rigidity of the earth. Part of the conclusion is as follows which has been obtained by studying the settling behaviors observed in examples of vertical ...

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the reactor blockages occurring in the course of direct hydroliquefaction of Miike coal, Taiheiyo coal and Yallourn coal briquets in a tubular reactor. The liquefaction tests were carried out at 450 C under 24.6 MPa hydrogen pressure, with red mud and sulfur catalyst. From the observed balances for catalyst and coal ash, it was inferred that reactor blockages are due to sedimentation of catalyst and ash. The conditions for catalyst and coal ash run-off were determined after solvent and slurry flow rates had been altered to suit the type of coal being tested. It was found that ash run-off occurred more readily as the difference between the slurry flow velocity and the natural sedimentation velocity of red mud in the coal liquids increased. Even when ash run-off was occurring, however, the ash concentration of the slurry in the reactor was higher than the concentration in the feed ...

Science.gov (United States)

Because hydrogenation of coal to liquid products (oils) is accompanied by distributions of complex by-product mixtures (IOM, preasphaltenes, asphaltenes and gases) which change as a function of reaction variables (time, temperature and pressure) and reactor configuration, the determination of selectivity relationships for coal liquefaction catalysts has been a difficult and time-consuming task involving numerous experiments to adequately describe catalyst performance over a range of conditions. This paper describes a method for analyzing the experimental results of coal liquefaction reactions which may be applied to a number of aspects of coal liquefaction research and process control, including: rapid selectivity and performance screening for catalysts; correlation of laboratory results with process parameters; and optimization of product yield for plant process conditions. Catalyst selectivity and ...

Energy Technology Data Exchange (ETDEWEB)

It is thought that iron-based catalysts for coal liquefaction exercise their catalytic activity by forming pyrrhotite (Fe(1-x)S). However, there are still a lot of unknown problems remained concerning the formation and agglomeration behaviors of pyrrhotite. These make a difficulty for improving the activity of iron-based catalysts. In this study, sulfiding behaviors of {alpha}-iron oxyhydroxide ({alpha}-FeOOH) and {gamma}-iron oxyhydroxide ({gamma}-FeOOH) were investigated to reveal the formation and agglomeration behaviors of pyrrhotite. It was found that pyrrhotite was easily converted from ferric oxyhydroxide catalysts having large specific surface areas at the sulfiding temperature below 250{degree}C, and fine crystallites of pyrrhotite were formed at the initial stage of sulfiding. Crystal growth of pyrrhotite at the sulfiding temperature over 350{degree}C depended on the catalyst forms. It was ...

International Nuclear Information System (INIS)

Palladium/magnetite nanoparticulate catalysts were developed for efficient elimination of halogenated organic pollutants from contaminated wastewater. Particle recovery from treated water can be ensured via magnetic separation. However, in worst-case scenarios, this catalyst removal step might fail, leading to particle release into the environment. Therefore, a toxicological study was conducted to investigate the impact of both pure magnetite and palladium/magnetite nanoparticle exposure upon human skin (HaCaT) and human colon (CaCo-2) cell lines and a cell line from rainbow trout gills (RTgill-W1). To quantify cell viability after particle exposure, three endpoints were examined for all tested cell lines. Additionally, the formation of reactive oxygen species was studied for the human cells. The results showed only minor effects of the particles on the tested cell systems and support the assumption that palladium/magnetite ...

Science.gov (United States)

In October 1980, Air Products and Chemicals, Inc. began a three year contract with the DOE: Catalyst and Reactor Development for a Liquid Phase Fischer-Tropsch Process. The program contains four major tasks: (1) Project Work Plan, (2) Slurry Catalyst Development, (3) Slurry Reactor Design Studies, and (4) Pilot Facility Design. This report describes work on Tasks 2 and 3 carried out in the third quarter of the contract. In Task 2, the computerized search of the Fischer-Tropsch literature was continued, and improvements were made in data processing programs. Shakedown tests were completed on the first 300 ml slurry reactor, and construction of the second and third reactors began. Five modified conventional slurry catalysts were prepared, and two batches were tested in the gas phase giving information on selectivity as a function of composition and activation. Four supported cluster catalyst were ...

Science.gov (United States)

This report presents the results of Run 261 performed at the Advanced Coal Liquefaction R & D Facility in Wilsonville, Alabama. The run started on January 12, 1991 and continued until May 31, 1991, operating in the Close-Coupled Integrated Two-Stage Liquefaction mode processing Illinois No. 6 seam bituminous coal (from Burning star No. 2 mine). In the first part of Run 261, a new bimodal catalyst, EXP-AO-60, was tested for its performance and attrition characteristics in the catalytic/catalytic mode of the CC-ITSL process. The main objective of this part of the run was to obtain good process performance in the low/high temperature mode of operation along with well-defined distillation product end boiling points. In the second part of Run 261, Criterion (Shell) 324 catalyst was tested. The objective of this test was to evaluate the operational stability and catalyst and process performance while processing the high ash ...

British Library Electronic Table of Contents (United Kingdom)

Abstract The creation of chirality on Earth and the development of chiral life have been discussed in this highlight. Convincing evidence for the introduction of chirality on Earth is still fragmentary. We believe that by a combination of chiral crystallization and formation of helical polymers with preferred chiral conformational structure is the key to this question. This concept of macromolecular asymmetry has inspired ideas and resulted in possible rules for how chiral life as we know it, could have been introduced. These investigations needed the understanding of the requirements for chiral crystallization, for the stereochemistry of the initial formation of helical polymers, the measurements of optical activity of solids and their coordination with the fundamentals of chirality. Spac...

British Library Electronic Table of Contents (United Kingdom)

The gravitational torque applied on the Earth by the other celestial bodies generates periodic variations in the orientation of the Earth's rotation axis in space which are called nutations. Observations of Earth's nutations allow for insights into the physical properties of the inner core because of the presence of a normal mode, the Free Inner Core Nutation (FICN), which is characterized by a tilt of the inner core figure and rotation axes with respect to the mantle and outer core. The frequency of the FICN is controlled by the strength of the mechanical coupling acting at the inner core boundary (ICB) and by the ability of the inner core to deform under the action of centrifugal and gravitational forces. Attenuation of the FICN reflects energy dissipated by electromagnetic (EM) and visc...

Science.gov (United States)

Nov 8, 2010 ... Ihring Mission 11, the radiation dosimetry measurement system functioned normally and provided data on the Earth's trapped radiation belts ...

Energy Technology Data Exchange (ETDEWEB)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements.

Science.gov (United States)

... Astronomy & Space Biology Chemistry & Materials Computing Earth & Environment Education ... Materials Research Center at the University of Chicago, one of nearly 30 NSF-supported Materials ...

Science.gov (United States)

The rapidly growing field of remote sensing is beginning to supply massive amounts of high resolution imagery of the earth and other planets. ...

Science.gov (United States)

Feb 15, 2010 ... This astronaut photo from January 4, 2010, shows meander scars and oxbow lakes in the floodplain of the Rio Negro in South America.

Science.gov (United States)

Federal regulators were set to vote on a plan to protect deep water corals and other sensitive fish habitats that will likely include a permanent ban on ...

British Library Electronic Table of Contents (United Kingdom)

This study presents new software, called Google Earth-based Optimal HAulage RouTing System (GEOHARTS), to improve the functionality of Google Earth for optimal haulage routing of off-road dump trucks in construction and mining sites. A modified least-cost path algorithm, which is applicable to working areas with both paved and unpaved temporary roads and can consider the effects of terrain relief and curves along a route on the route planning, was proposed and utilized for the software development. GEOHARTS can determine optimal haulage routes between loaders and dumps that ensure the least travel time or fuel consumption of off-road dump trucks and can visualize the results using an embedded 3D render window of Google Earth. The application to the Pasir open-pit coal mine in Indonesia dem...

Science.gov (United States)

Satellite Observations of the Southeast Pacific Intertropical Convergence Zone During 1993-1998, Halpern, D.; Hung, C.-W., Journal of Geophysical Research ? ...

Science.gov (United States)

of Earth Science data and information management capabilities. Dale Schulz/400 . For your exceptional achievement in leading the joint LaRC/GSFC team in ...

Science.gov (United States)

The portion of the Waterpocket Fold illustrated in this image includes layered rocks formed during the Mesozoic Era (~ 250 65 million years ago) the oldest ...

CERN Document Server

The abstract is additional with repect to the paper published in JGCD. Ordinary Earth satellites are usually placed into five categories of special orbits: sun-synchronous orbits, orbits at the critical inclination, frozen orbits, repeating ground track orbits, and geostationary orbits. This paper investigates their counterparts around Mars and examines the basic nature of these orbits, which are of special interest for missions conducted around Mars, including Mars reconnaissance. Mars' gravity field is much more complicated, with relatively smaller J2, compared to Earth's, which makes the behaviors of these Martian orbits different from those of Earth. Analytical formulations and numerical simulations are used to analyze these Martian orbits and compare them with their Earth counterparts. First, mean element theory is employed to describe variations of orbital elements and give the constraint ...

Science.gov (United States)

Turbine Afterword The SHARP cannon. Hydrogen is compressed in the tube on top, the gun barrel is on bottom. When Jules Verne wrote in 1865 "From Earth to the Moon" he envisioned...

International Nuclear Information System (INIS)

... gamma cascades kev range 10-100 lifetime lutetium 171 lutetium 173 lutetium

Science.gov (United States)

Deforestation in Mato Grosso, Brazil. atom_author. atom_name, Jesse Allen. atom_link. kml_href, http://earthobservatory.nasa.gov/Feeds/GoogleEarth/ ...

British Library Electronic Table of Contents (United Kingdom)

World demand for rare-earth elements and the metal yttrium?which are crucial for novel electronic equipment and green-energy technologies?is increasing rapidly. Several types of seafloor sediment harbour high concentrations of these elements. However, seafloor sediments have not been regarded as a rare-earth element and yttrium resource, because data on the spatial distribution of these deposits are insufficient. Here, we report measurements of the elemental composition of over 2,000 seafloor sediments, sampled at depth intervals of around one metre, at 78 sites that cover a large part of the Pacific Ocean. We show that deep-sea mud contains high concentrations of rare-earth elements and yttrium at numerous sites throughout the eastern South and central North Pacific. We estimate that an a...

Science.gov (United States)

switch when this cavity matching condition is determined. This results is a ... MHz offset is provided by an acousto-optic modulator. (AOM). The AOM will be shut ...

Energy Technology Data Exchange (ETDEWEB)

Sulfur poisoning from engine fuel and lube is one of the most recognizable degradation mechanisms of a NOx adsorber catalyst system for diesel emission reduction. Even with the availability of 15 ppm sulfur diesel fuel, NOx adsorber will be deactivated without an effective sulfur management. Two general pathways are currently being explored for sulfur management: (1) the use of a disposable SOx trap that can be replaced or rejuvenated offline periodically, and (2) the use of diesel fuel injection in the exhaust and high temperature de-sulfation approach to remove the sulfur poisons to recover the NOx trapping efficiency. The major concern of the de-sulfation process is the many prolonged high temperature rich cycles that catalyst will encounter during its useful life. It is shown that NOx adsorber catalyst suffers some loss of its trapping capacity upon high temperature lean-rich exposure. With the use of a disposable SOx ...

Energy Technology Data Exchange (ETDEWEB)

The effect of thermal pretreatment in N[sub 2] up to 723 K and the activation treatments in H[sub 2] and an inert atmosphere on the properties of Ni and Co activated-charcoal-supported catalysts were studied. Catalysts were characterized by means of N[sub 2] adsorption at 77 K, H[sub 2] chemisorption at room temperature, thermogravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The catalysts' activity and selectivity for acetone hydrogenation to 2-propanol under unusual and severe conditions (473 K and high overall acetone conversion) were also measured. TGA and XRD evidence was found for the charcoal-support-promoted NiO and CoO reduction to the metallic states when the catalysts were subjected to an inert atmosphere above 723 K caused a loss of acetone hydrogenation activity (calculated on a metal load basis) for both the Ni and Co ...

Energy Technology Data Exchange (ETDEWEB)

Selective catalytic reduction (SCR) of nitrogen oxides(NO{sub x}) in flue gas or engine exhaust gas with hydrocarbons as the reductant has great potential for less expense, less pollution, and easier operation than SCR with ammonia. Methane is the preferred reducing gas because of its low cost and low toxicity. Stable, low-cost catalysts for SCR with methane are required to demonstrate this technology for controlling NO{sub x} emissions. Several cobalt and nickel catalysts on synthetic clay and uranium oxide supports were investigated for their activities in reducing NO{sub x} with methane in the presence of air. The efficiency of the synthetic clay-supported nickel and cobalt catalysts for nitric oxide (NO) reduction with methane as the reducing gas was poor. The nickel oxide-uranium oxide catalyst, which was chosen for its high stability, was also ineffective. Results from the two-step experiments ...

Energy Technology Data Exchange (ETDEWEB)

Aimed at post-graduate and post-doctoral researchers in geochemistry, this book reflects the rapid changes in the applications of radioactive and stable isotope analysis to a range of geological and geochemical problems. Isotropic chemistry and methods used in mass spectroscopy are discussed initially. The second section deals with radiometric dating methods. The role of isotopes in climate and environmental research is also explored. The book closes with a section on extra-terrestrial matter, geothermometry and the isotopic geochemistry of the Earth`s lithosphere. (UK).

Energy Technology Data Exchange (ETDEWEB)

Clays and zeolites are among the most important of natural dusts by virtue of their occurrence through out the world on the earth`s surface and their important industrial uses. (The 1:1 layer silicates, including the serpentine and kaolin minerals, are not addressed in this chapter.) This chapter provides basic information on a variety of important aspects of each mineral, including crystal structure diagrams of each and references to more detailed discussions. 110 refs., 20 figs.

CERN Document Server

Among the billions of planetary systems that fill the Universe, we would like to know how ours fits in. Exoplanet data can already be used to address the question: How common are Jupiters? Here we discuss a simple analysis of recent exoplanet data indicating that Jupiter is a typical massive planet rather than an outlier. A more difficult question to address is: How common are Earths? However, much indirect evidence suggests that wet rocky planets are common.

Wastenet

...Observatory Edinburgh SkyView Virtual Observatory Solar System Simulator Space Telescope Science Institute Space Weather : A Research Perspective Subaru Telescope Project Two Micron All ...Universities for Research in Astronomy Subjects: space observation DeweyClass: 522 Resource type: index Space Weather : A Research Perspective Documents discussing space weather , the ...elements of near-Earth space, Earth-space meteorology and practical consequences of space weather . Glossary included. Author: National Academy of ...

Energy Technology Data Exchange (ETDEWEB)

When a bipolar HVDC transmission system is operating monopolar using the earth as a return path, it is often desired to divert the return current from the earth to the line from the unused pole. To do so requires either that the system be shut down temporarily or that a dc circuit breaker be used. This paper describes the development of such a new dc circuit breaker, and its application on the Pacific Intertie as a Metallic Return Transfer Breaker (MRTB).

International Nuclear Information System (INIS)

This work describes a three-step pre-treatment route for processing spent commercial Ni Mo/Al_2O_3 catalysts. Extraction of soluble coke with n-hexane and/or leaching of foulant elements with oxalic acid were performed before burning insoluble coke under air. Oxidized catalysts were leached with 9 mol L"-"1 sulfuric acid. Iron was the only foulant element partially leached by oxalic acid. The amount of insoluble matter in sulfuric acid was drastically reduced when iron and/or soluble coke were previously removed. Losses of active phase metals (Ni, Mo) during leaching with oxalic acid were compensated by the increase of their recovery in the sulfuric acid leachate. (author)

Scientific Electronic Library Online (English)

Abstract in english Ru(1%)/SiO2 and Cu(1%)Ru(1%)/SiO2 catalysts were prepared by cogelation. The effect of pH and the amount of water on the physical-chemical properties and the catalytic properties of them were analyzed. The acid medium increased the formation of microporosity and the formation of small size of metallic ruthenium particle. The variation of the water quantity used in the gelation not modify considerably the texture neither the dispersion of the noble metal. The reduction lev (more) el of all prepared catalyst was similar, showing displacement in some of reduction peaks. The toluene hydrogenation indicated that the conversion and the quantity of hydrogenate product varied with the pH and the quantity of water used in the gelation. The addition of copper to Ru/SiO2 catalysts diminished the reactive conversion and their hydrogenant activity

British Library Electronic Table of Contents (United Kingdom)

A dense Pd-Ag membrane reactor (MR) with 100% hydrogen selectivity packed with either Rh/La2O3 or Rh/La2O3-SiO2 as catalysts was used to carry out the dry reforming of methane. The membrane reactor simulation was performed using a well-known reactor model. For this purpose, we employed the equations derived from complete kinetic studies of the dry reforming of methane reaction in connection with both catalysts. In addition, we developed the kinetic equation for the reverse water gas shift reaction (RWGS). The combination of detailed kinetic studies with the measured permeation flux for the Pd-Ag membrane allowed a complete comparison between experimental and simulated operation variables. The variables studied for both catalysts were methane conversion and hydrogen permeation as a function...

Energy Technology Data Exchange (ETDEWEB)

A kinetic model based on the Mars-van Krevelen mechanism that allows to describe the microkinetics of the heterogeneously catalysed partial oxidation of {alpha}, {beta}-unsaturated aldehydes is presented. This conversion is represented by a network, composed of the oxidation of the {alpha}, {beta}-unsaturated aldehyde towards the {alpha}, {beta}-unsaturated carboxylic acid and the consecutive oxidation of the acid as well as the parallel reaction of the aldehyde to products of deeper oxidation. The reaction steps of aldehyde respectively acid oxidation and catalyst reoxidation have been investigated separately in transient experiments. The combination of steady state and transient experiments has led to an improved understanding of the interaction of the catalyst with the aldehyde and the carboxylic acids as well as to a support of the kinetic model assumptions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Hydrogenation of napthalene to tetralin using activated red mud as catalyst was studied as a typical hydrogen-donor system. Under the chosen reaction conditions, unprocessed red mud resulted in a conversion of napthalene of 3.55%. The most active catalyst, prepared by adding 20 wt% of TiO/SUB/2 to the red mud, followed by acid digestion and re-precipitation, resulted in a 58% conversion of naphthalene. This technology may have an important bearing on processes such as coal hydrogenation or crude-oil-residue processing, where the rate of reaction and product quality may depend upon the rate at which a hydrogen-donor solvent can be re-hydrogenated. (7 refs.)

British Library Electronic Table of Contents (United Kingdom)

Abstract Dynamic testing of a phosphoric acid-based high temperature PEM fuel cell shows a peculiar phenomenon. A certain current loss is observed after temperature cycling at constant voltage. This loss is incidentally recovered by applying a cell voltage spike to open circuit voltage. Experimental investigations into temperature, cell voltage, and ageing effects show that this phenomenon might occur due to the orientation of the adsorbed phosphate species on the platinum catalyst surface. Along with some supporting literature and experimental results, a hypothesis is presented in order to explain this occurrence. Phosphoric acid adsorption hysteresis on platinum catalyst due to temperature cycling could cause the temporary cell current loss. Electrode potential-dependent molecule symmetr...

Energy Technology Data Exchange (ETDEWEB)

A residue in the production of alumina by the Bayer process is red mud. It contains oxides of Fe and Ti, active as hydrogenation catalyst in sulfided form, and whose catalytic activity can be improved by the activation method proposed by Pratt and Christoverson. The paper describes how the development of its activity and selectivity with reaction time was studied for the hydrogenation of a light fraction of an anthracene oil, and compared with untreated sulfided red mud. Catalyst samples were collected at different reaction times, and their texture, morphology and composition characterized by nitrogen adsorption, SEM and SEM-EDX. The loss of catalytic activity of activated sulfided red mud is slower than for untreated sulfided red mud. The main cause of this decrease in catalytic activity is the loss of surface area and superficial Fe.

Energy Technology Data Exchange (ETDEWEB)

A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).

CERN Document Server

The bright star 55 Cancri is known to host five planets, including a transiting super-Earth. The interferometric study presented here yields directly determined values for 55 Cnc's stellar astrophyiscal parameters: $R=0.943 \\pm 0.010 R_{\\odot}$, $T_{\\rm EFF} = 5196 \\pm 24$ K. We use isochrone fitting to determine 55 Cnc's age to be 10.2 $\\pm$ 2.5 Gyr, implying a stellar mass of $0.905 \\pm 0.015 M_{\\odot}$. Our analysis of the location and extent of the system's habitable zone (0.67--1.32 AU) shows that planet f ($M \\sin i = 0.155 M_{Jupiter}$) spends the majority of the duration of its elliptical orbit in the circumstellar habitable zone, where, with moderate greenhouse heating, it could harbor liquid water. Finally, our direct value for 55 Cancri's stellar radius allows for a model-independent calculation of the physical diameter of the transiting super-Earth 55 Cnc e ($\\sim 2.05 \\pm 0.15 R_{\\earth}$), which, ...

UK PubMed Central (United Kingdom)

Some biological effects of hypoglycin-A, a compound isolated from the fruit of Blighia sapida, have been investigated. Administration of this compound to animals caused drowsiness...Full Text Available

UK PubMed Central (United Kingdom)

Woolfolk, C. A. (University of Washington, Seattle). Reduction of inorganic compounds with molecular hydrogen by Micrococcus lactilyticus. II. Stoichiometry with inorganic...Full Text Available

Science.gov (United States)

The report contains general information on aluminium and aluminium compounds concerning the existing standards, emissions, exposure levels and effect levels. The document is to be considered as a first evaluation to be used for the national discussion dur...

International Nuclear Information System (INIS)

... organic compounds other organic compounds separation processes

UK PubMed Central (United Kingdom)

Enzymes are versatile catalysts in laboratories and on an industrial scale; improving their immobilization would be beneficial to broadening their applicability and ensuring their (re)use. Lipid-coated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Propylene polymerizations were carried out with {phi}{sub 2}C(Flu)(Cp)ZrCl{sub 2} and SiMe{sub 2}(Ind)2ZrCl{sub 2} catalysts supported on silica, zeolite sodic mordenite (NaM) and acid mordenite (HM). The polymerizations were performed at different temperatures and varying aluminium/zirconium molar ratios ([Al]/[Zr]). The effect of these reaction parameters on the catalyst activity was investigated using a proposed statistical experimental planning. In the case of f{sub 2}C(Flu)(Cp)ZrCl{sub 2}, SiO{sub 2} and NaM were used as support and the catalyst performance evaluated using toluene and pentane as polymerization solvent. The molecular weight, molecular weight distribution, melting point and crystallinity of the polymers were examined. The results indicate very high activities for the syndiospecific heterogeneous system. Also, the polymers obtained had superior Mw and stereo regularity. (author)

Science.gov (United States)

A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization (FGD) system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and -0.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. Pilot tests showed ...

Wastenet

...wood smoke, emissions, pollution, heaters, environment, Earthbeat - 25/5/2002: Woodsmoke, Health & the Environment Love that Planet All in the Mind The Buzz Health Report In Conversation Ockhams Razor Science Show The Lab Health Matters Catalyst Quantum ...

Energy Technology Data Exchange (ETDEWEB)

Work continued on the correlations of catalytic activity of metals and surface structure. Work is described in the following areas: CO oxidation on a Cu/Rh(100) Bimetallic catalysts; electronic properties of bimetallic surfaces; and reflection absorption spectroscopy of bimetallic surfaces. 5 figs. (CBS)

Energy Technology Data Exchange (ETDEWEB)

Modern combined cycle power plants with natural gas as the only fuel reach efficiencies of up to 58% for electric power generation. Nevertheless the reserves of natural gas are more limited compared to the reserves of coal. Therefore possibilities should be investigated to use coal for such plants also. One concept, that combines the use of coal in a combined cycle application with high efficiencies is examined in this paper. According to this concept the exhaust gas of the gas turbine (vitiated air) is the combustion air for the pulverised coal combustion, that takes place in the bottoming steam generator. Due to the low oxygen content of the vitiated air the burnout of the coal may be incomplete. In order to avoid the incomplete combustion of the coal and the resulting decrease of the efficiency of the plant and possible emission problems, a catalyst, that converts carbon monoxide and unburnt carbon to carbon dioxide should be installed between the heating ...

Energy Technology Data Exchange (ETDEWEB)

Despite the rapid development of literature pertaining to fundamental (1-4) studies of oxidation catalysis, a general theory of heterogeneous selective oxidation catalysis explaining the selectivity behavior of different metal oxide systems has not yet been developed. Redox mechanisms have been widely invoked in the kinetic and mechanistic descriptions of selective oxidation reactions, suggesting a dynamic behavior of hydrocarbon and oxygen interactions with the catalyst surface. Nevertheless, most of the recent theoretical approaches of this subject matter (5-7) are essentially static in nature. Correlations are made with surface structure on the basis of crystallographic considerations with selectivity being related to the nature, number, bond-strength and nearness of oxygen atoms in the neighborhood of adsorption centers. The effect of the reaction medium on the configuration of the catalyst surface, and thus its influence on the reaction ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the effect of blending of two different coals in various ratios on the hydrogenation reaction was carried out using a red mud-sulphur catalyst. Three Japanese coals and an Australian brown coal were used in the study. The conversion of the blended coals was compared with that obtained with each of the coals alone. A blend of the Yallourn brown coal and Shin-Yubari coal showed a synergism: it is considered that hydroaromatics from the Japanese coal promote the hydrogenation of the Yallourn coal. (The tables and captions in this paper are in English).

Energy Technology Data Exchange (ETDEWEB)

Applying the thermochemical selectivity criterion of Hadnett et al. It is shown that the selectivity of the furan formation is not limited by a too low strength of the C-H bonds in furan when compared with the C-H bond dissociation energy in the educt molecule butadiene. In the oxidation of butadiene on a CsH{sub 2}PMo{sub 12}O{sub 40} catalyst a maximum yield of 22 mol% furan has been obtained. To improve this comparatively low furan yield oxidation activity of the catalyst must be lowered to prevent the consecutive reaction to maleic anhydride. (orig.)