Solid state effects are taken into account in an internal conversioncoefficients computation by using Wigner-Seitz boundary conditions. Both the bound and free electron wave functions are calculated from an atomic Dirac-Hartree-Fock-Slater self consistent potential. These internal conversioncoefficients are compared with those obtained from the usual free atom boundary conditions.
Solid state effects are taken into account in an internal conversioncoefficients computation by using Wigner-Seitz boundary conditions. Both the bound and free electron wave functions are calculated from an atomic Dirac-Hartree-Fock-Slater self consistent potential. These internal conversioncoefficients are compared with those obtained from the usual free atom boundary conditions. (orig.).
Endoreduplication represents a cell cycle variant during which multiple rounds of DNA replication occur without subsequent chromosome separation and cytokinesis, resulting into a cellular increase of the DNA content. Although the DNA ploidy level of cells is controlled by external stimuli such as light, currently limited knowledge is available on how environmental signals regulate the endoreduplication cycle at the molecular level. Previously, we have demonstrated that the conversion from the mitotic cell cycle into an endoreduplication cycle is mediated by the atypical E2F transcription factor DEL1 that operates as a repressor of endocycle onset. Here, we identified DEL1 as a transcriptional target of the classical E2Fb and E2Fc transcription factors that antagonistically control DEL1 transcript levels through competition for a single ...
The thermal accommodation coefficients of helium, neon, argon, hydrogen and deuterium have been measured in the temperature range of 77-340 K on the surface of a graphitized carbon filament. The dependence of the accommodation coefficient upon the molecular weight as well as the temperature of measurement, and the conversion from orthohydrogen to parahydrogen, have been discussed.
The magnetic #beta#-spectrometer of the #pi# #sq root#2 type with 0.07% pulse resolution is used to measure the intensities of interval conversion electrons on L- and M-subshells of 70.45 keV "1"7"7 Ta gamma-transition. The results are analyzed and the values of mixing parameter #sigma#(E2/M1) and penetration parameter #lambda# are obtained.
The carbon content of silicon single crystals and polycrystals has been measured by charged particle activation analysis (CPAA) and infrared absorption. The authors obtained a linear relationship between the absorption coefficient at 605 cm/sup -1/ and the carbon content obtained by CPAA. They obtained a conversion factor of (1.00 +- 0.03) 10/sup 17//cm/sup 2/ for a 100% substitutional carbon.
Measurements of {gamma}-ray, {gamma}{gamma}-coincidence and internal conversion electron spectra from the {sup 106}Cd({alpha},n{gamma}){sup 109}Sn reaction were carried out at 15-20 MeV {alpha}-particle bombarding energies with Ge(HP) {gamma}-ray and superconducting magnetic lens plus Si(Li) electron spectrometers. The energies, relative intensities, internal conversioncoefficients and coincidence relations of the {sup 109}Sn transitions were determined, and a more complete, consistent level scheme has been deduced. Spin and parity values have been determined from the internal conversioncoefficients, the bombarding-energy dependence of the side-feeding intensities of the states and the available {gamma}-ray angular distribution data. The level scheme was interpreted in the framework of the quasi-particle shell model.
Purpose: calculation of conversioncoefficients for the reconstruction of organ doses from entrance doses for abdomen radiographs of 0, 1, 5, 10, 15, and 30-year-old patients in conventional pediatric radiology for the radiographic settings recommended by the German and European guidelines for quality management in diagnostic radiology. Materials und method: using the commercially available personal computer program PCXMC developed by the Finnish Center for Radiation and Nuclear Safety (Saeteilyturvakeskus STUK), conversioncoefficients for conventional abdomen radiographs were calculated performing Monte Carlo simulations in mathematical hermaphrodite phantom models describing patients of different ages. The possible clinical variation of beam collimation was taken into consideration by defining optimal and suboptimal radiation fields on the phantoms' surfaces. Results: ...
The most important commercialized methods of attenuation correction in SPECT are based on attenuation coefficient map from a transmission imaging method. The transmission imaging system can be the linear source of radioelement or a X-ray CT system. The image of transmission imaging system is not useful unless to replacement of the attenuation coefficient or CT number with the attenuation coefficient in SPECT energy. In this paper we essay to evaluate the validity and estimate the error of the most used method of this transformation. The final result shows that the methods which use a linear or multi-linear curve accept a error in their estimation. The value of mA is not important but the patient thickness is very important and it can introduce a error more than 10 percent in the final result.
Epidemiological studies have revealed that butyrate and 17?-estradiol (E2) may decrease the incidence of colorectal cancer (CRC). In peripheral tissue, E2 can be produced locally by 17?-hydroxysteroid dehydrogenase 1 (HSD17B1) estrone (E1) reduction. Using quantitative real-time polymerase chain reaction and western blotting analysis, we found that sodium butyrate significantly upregulates HSD17B1 long and short transcripts and protein levels in HT29 and SW707 CRC cells. Chromatin immunoprecipitation analysis showed that upregulation of these transcript levels correlated with an increase in binding of Polymerase II to proximal and distal promoters of HSD17B1. Moreover, we observed that upregulation of HSD17B1 protein levels was associated with increased conversion of E1 to E2 in HT29 and S...
Carbon monoxide, H{sub 2}, and CO{sub 2} in synthesis gas can be converted to CH{sub 4} by employing a triculture of Rhodospirillum rubrum, Methanosarcina barkeri, and Methanobacterium formicicum. Trickle-bed reactors have been found to be effective for this conversion because of their high mass-transfer coefficients. This paper compares results obtained for the conversion of synthesis gas to CH{sub 4} in 5-cm- and 16.5-cm-diameter trickle-bed reactors. Mass-transfer and scale-up parameters are defined, and light requirements for R. rubrum are considered in bioreactor design.
We iterate Manolescu's unoriented skein exact triangle in knot Floer homology with coefficients in the fraction field of the group ring (Z/2Z)[Z]. The result is a spectral sequence which converges to a stabilized version of delta-graded knot Floer homology. The (E_2,d_2) page of this spectral sequence is an algorithmically computable chain complex expressed in terms of spanning trees, and we show that there are no higher differentials. This gives the first combinatorial spanning tree model for knot Floer homology.
This paper examines cupric chloride solid conversion during hydrolysis in a thermochemical copper-chlorine (Cu-Cl) cycle for hydrogen production. The hydrolysis reaction is a challenging step, in terms of the excess steam requirement and the decomposition of cupric chloride (CuCl_2) into cuprous chloride (CuCl) and chlorine (Cl_2). The hydrolysis and decomposition reactions are analyzed with respect to the chemical equilibrium constant. The effects of operating parameters are examined, including the temperature, pressure, excess steam and equilibrium conversion. A maximization of yield and selectivity are very important. Rate constants for the simultaneous reaction steps are determined using a uniform reaction model. A shrinking core model is used to determine the rate coefficients and predict the solid conversion time, with diffusional and reaction control. These new results are useful for scale-up of ...
An experimental investigation of the 70.5 keV #gamma#-ray transition from the 55/22"+[402] state to the 77/22"+[404] ground state in "1"7"7Ta was made. The half-life and magnetic moment of the initial state were found to be 73+-5 ns and 4.7+-0.5 #mu#sub(N) respectively. The E2/M1 mixing ratio of the transition was determined to be -0.10+-0.04. The reduced transition probabilities, B(E2) and B(M1), were found to be 2.9+-2.3e"2.fm"4 and (1.1+-0.1)x10"-"4#mu#sub(N)"2, respectively, and the M1 penetration parameter was determined to be 6+-2. The Coriolis mixing amplitude of the 75/22"+[402] state in the 77/22"+[404] ground state was determined from the B(E2) value to be -0.011+-0.004. It was found that the experimental value of the Coriolis matrix element <5/2"+/j-/7/2"+>sub(exp) was one-tenth of that calculated using ...
Intermediate products of the conversions of 6-aminophenalenone in ethanol were investigated by pulse radiolysis. In alkaline medium the main product is the 6-aminophenalenone radical cation, the optical absorption spectrum of which contains two bands with maxima at 355 and 400 nm. The precursors of this particle are e_s, CH_3CHOH and CH_3CHO"- radicals. In neutral and acid medium, radical cations are protonated in reactions with alcohol and hydrogen ions. The H-adduct of 6-aminophenalenone that arises has optical absorption maxima at 350 and 390 nm. The presence of two maxima is due to two different structures of the product. The molar extinction coefficients of the radical anions and H-adducts of 6-aminophenalenone and the rate constants of the reactions involving them were estimated. 6 refs., 4 figs., 2 tabs.
In this study, the degrees of destruction of hemoglobin irradiated in atmospheres of air and argon were compared. Hemoglobin preparations were irradiated in the forms: oxyhemoglobin (HbO_2) deoxyhemoglobin (Hb"2"+) and methemoglobin (MetHb) applying doses of 0.5 to 5 Mrad. The degree of hemoglobin destruction was estimate on the basis of changes in the values of the absorption coefficient at the Soret band, the absorption ratio A_5_0_5/A_5_6_3 determined after conversion of irradiated preparations into MetHb, absorption coefficinets for pyridine hemochromogen obtained from irradiated preparations, and changes in parameters characterizing the hemoglobin oxygenation reaction (log p/sub 1/2/O_2 and the Hill n coefficient). The calculated oxygen enhancement ratios S were generally higher than 1 for the parameters estimated. This indicates that the presence of oxygen during irradiation enhances hemoglobin destruction.
The detector for retrospective radon exposure measurements is developed. The detector consists of the multilayer package of solid-state nuclear track detectors LR-115 type. Nitrocellulose films works both as {alpha}-particle detector and as absorber decreasing the energy of {alpha}-particles. The uncertainties of implanted {sup 210}Pb measurements by two- and three-layer detectors are assessed in dependence on surface {sup 210}Po activity and gross background activity of the glass. The generalized compartment behavior model of radon decay products in the room atmosphere was developed and verified. It is shown that the most influencing parameters on the value of conversioncoefficient from {sup 210}Po surface activity to average radon concentration are aerosol particles concentration, deposition velocity of unattached {sup 218}Po and air exchange rate. It is demonstrated that with the use of additional information on surface to volume room ...
An experimental investigation was made of the ..gamma..-transitions feeding or de-exciting the 1355 keV isomeric state in /sup 177/Ta. The E2/M1 mixing ratios for the 311 keV interband transition from the isomer and for the 271 keV and the 295 keV intraband transitions within the rotational band on the isomer were determined to be delta = 0.29sup(+0.11)sub(-0.06), 0.25sup(+0.05)sub(-0.03) and 0.30sup(+0.06)sub(-0.08), respectively, employing combined measurements of the linear polarization and angular distribution of the ..gamma..-ray with the aid of conversion electron measurements. Spin and parity assignments of the isomer were confirmed to be 21/2/sup -/. The half-life of the isomer was remeasured to be Tsub(1/2) = 5.0 +- 0.2 ..mu..s and the magnetic moment was found to be ..mu.. = 0.080 +- 0.014 ..mu..sub(N). The gsub(K) and gsub(R) factors for the band on the isomer were deduced separately to be gsub(K=21/2/sup -/) = ...
An experimental investigation was made of the #gamma#-transitions feeding or de-exciting the 1355 keV isomeric state in "1"7"7Ta. The E2/M1 mixing ratios for the 311 keV interband transition from the isomer and for the 271 keV and the 295 keV intraband transitions within the rotational band on the isomer were determined to be delta = 0.29sup(+0.11)sub(-0.06), 0.25sup(+0.05)sub(-0.03) and 0.30sup(+0.06)sub(-0.08), respectively, employing combined measurements of the linear polarization and angular distribution of the #gamma#-ray with the aid of conversion electron measurements. Spin and parity assignments of the isomer were confirmed to be 21/2"-. The half-life of the isomer was remeasured to be Tsub(1/2) = 5.0 +- 0.2 #mu#s and the magnetic moment was found to be #mu# = 0.080 +- 0.014 #mu#sub(N). The gsub(K) and gsub(R) factors for the band on the isomer were deduced separately to be gsub(K=21/2"-) = ...
The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor, based on the experienced light water reactor (LWR) technology, aiming at effective utilization of uranium resources, high burn-up and long operation cycle and plutonium multiple recycling. These characteristics can be achieved by the high conversion ratio from {sup 238}U to {sup 239}Pu resulted from the higher neutron energy spectrum in comparison to conventional LWRs. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPC) in 1998, under technical cooperation with three Japanese reactor vendors. In the core design study of the RMWR, several basic core designs with the high conversion ratio more than 1 and the negative void reactivity coefficient have been ...
GaAs1-xPx p-n junction structures were grown on the epi-ready n-type GaAs(100) substrate by solid source MBE system for different phosphor compositions. To obtain the lattice-match sample structure was applied graded growth procedure. The structural and optical properties of the sample structures with different P concentration were investigated by using X-ray diffraction (XRD), spectroscopic ellipsometry (SE). In addition, The range of lattice parameters in the graded epilayer and phosphorous composition were determined from the HRXRD rocking curve simulation. We analyse dielectric function spectra of disordered GaAs1-xPx junction structures measured using spectroscopic ellipsometry at room temperature in the 0.6-4.7 eV photon energy region. The critical energy points such as band gap energy and spin-orbit-split energy of these structures were determined using SE data. It is detected that E0, E1 ,E2 energies of the GaAs1-xPx p-n junction ...
A kind of polymer-metal complex gel electrolyte is successfully prepared and is used in dye-sensitized solar cells. Raman and X-ray photoelectron spectroscopy confirm the structure of this complex and is found that the metal ion reacts with nitrogen in the polymer. This novel electrolyte shows apparent diffusion coefficient of iodide of 8.37 x 10-7 cm2 s-1 and the energy conversion efficiency of 6.10% when the amount of ZnI2 is 0.04 M. By studying the dissociation active energy of the inorganic salt in electrolytes, we find that the metal salts can dissociate more easily after reacting with polymer and as a result can provide extra free iodide ion. The cell maintains ca. 93% of its initial efficiency after 20 d without further sealing, which shows good long-time stability.
A more complete level scheme is presented here for the decay of [sup 187]Pt, incorporating many new lines and levels up to 2.4 MeV. Emphasis has been placed on the extraction of multipole mixing ratios from nuclear orientation data. Analysis of that data, however, required a more complete understanding of the level structure (including, in particular, branching ratios, conversioncoefficients, and level feedings), prompting the collection of new spectroscopy data. The low-lying, positive-parity levels are described in terms of (odd-proton) single-particle Nilsson states coupled to a triaxial core. Multipole mixing ratios are compared to those calculated in the Particle-Plus-Triaxial-Rotor Model. (orig.).
A more complete level scheme is presented here for the decay of "1"8"7Pt, incorporating many new lines and levels up to 2.4 MeV. Emphasis has been placed on the extraction of multipole mixing ratios from nuclear orientation data. Analysis of that data, however, required a more complete understanding of the level structure (including, in particular, branching ratios, conversioncoefficients, and level feedings), prompting the collection of new spectroscopy data. The low-lying, positive-parity levels are described in terms of (odd-proton) single-particle Nilsson states coupled to a triaxial core. Multipole mixing ratios are compared to those calculated in the Particle-Plus-Triaxial-Rotor Model. (orig.).
The cell cycle-regulatory transcription factor E2F-1 is regulated by interactions with proteins such as the retinoblastoma gene product and by cell cycle-dependent alterations in E2F-1 mRNA abundance....Full Text Available
This paper deals with conversions of solar energy efficiently into electricity and into gas laser radiation. In the first section, a review study of the possibility of a solar-electric thermophotovoltaic (TPV) device has been done. In a proposed extension of the TPV concept, a Cassagranian optical system concentrates solar radiation to heat a blackbody cavity to 2400/sup 0/K. A double-layer solar cell, GaAs and Si, forming the cylindrical surface concentric to the blackbody cavity, receives the blackbody radiation and converts it into electricity efficiently. A cell conversion efficiency of 50% or more would be possible with the TPV system. The second section explores the concept of blackbody radiation pumping of gas laser media as a step toward utilization of solar energy as a laser pumping source. To demonstrate this concept, an experiment was performed in which various gas mixtures of CO/sub 2/ and He were exposed to 1500/sup 0/K thermal ...
placed on direct energy conversion. This is an advanced technology which is ..... Of the direct energy conversion methods discussed, the only one which may ...
The mechanisms underlying the pathogenesis of estrogen-induced breast carcinogenesis remain unclear. The present study investigated the roles of estrogen metabolism and oxidative stress in estrogen-mediated mammary carcinogenesis in vivo. Female August Copenhagen Irish (ACI) rats were treated with 17b-estradiol (E2), the antioxidant vitamin C, the estrogen metabolic inhibitor a-naphthoflavone (ANF), or cotreated with E2 + vitamin C or E2 + ANF for up to 8 months. E2 (3 mg) was administered as an subcutaneous implant, ANF was given via diet (0.2%) and vitamin C (1%) was added to drinking water. At necropsy, breast tumor incidence in the E2, E2 + vitamin C and E2 + ANF groups was 82, 29 and 0%, ...
BackgroundHuman Papillomavirus (HPV) E2 plays several important roles in the viral cycle, including the transcriptional regulation of the oncogenes E6 and E7, the regulation of the...Full Text Available
Conversion electron studies of medium-heavy to heavy nuclear mass systems are important where the internal conversion process begins to dominate over gamma-ray emission. The use of a segmented detector array sensitive to conversion electrons has been used to study multiple conversion electron cascades from nuclear transitions. The application of the silicon array for conversion electron detection (SACRED) for in-beam measurements has successfully been implemented. (orig.). With 2 figs.
This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result due to correction coefficient for the solar cell ...
Measurements were carried out for calibration and performance testing of a set of 10 electronic personal dosimeters (EPDs) at the Secondary Standard Dosimetry Laboratory of Sudan. Calibrations were carried out at three X-ray beam qualities described in ISO standard 4037 in addition to 137Cs and 60Co gamma ray beams. The experimental was performed with EPDs mounted on ICRU Slab phantom. X-ray and ?-ray beams were characterized in terms of air kerma free-in-air which were converted to the known delivered personal dose equivalent, Hp(10) using appropriate the air kerma to personal dose equivalent conversioncoefficients. Dosimeters tested showed excellent energy and angular response and relative error of indication within the recommended limit for photon energies from 65 keV to 1.25 MeV. The study showed encouraging results for using electronic dosimeters in personal dosimetry.
The project is described, the motivation for the research and the microclimate is defined in relation to both building physics research and applications. Air temperatur, air humidity, solar radiation and air velocity are briefly considered, whilst driving rain and long-wave radiation are described in more detail. Convective heat transfer and surface coefficients are discussed, although they are not microclimatic factors, merely resulting from combinations of such factors. They are included as they are important in relation to transfer of heat and moisture at the surface of the building envelope. Driving rain measurement is the main area of interest, including development of measurement equipment. Long-wave irradiation is measured and compared with empirical formulae from the literature. Window convection heat transfer is another main area of interest. Nocturnal convective heat transfer from a double pane glazing is studied and measurement principles are discussed. ...
Under typical conditions found in Pressurized Fluidized Bed Combustion (PFBC), the calcination reaction of limestones is thermodynamically inhibited, and the sorbent reacts with SO{sub 2} by a direct mechanism. Direct sulfation reactivity of different Spanish sorbents was studied by high-pressure thermogravimetric analysis. It was found that the physical structure of the surface of the particles influence the sulfation behaviour of the sorbents. Total pore volume and pore surface area correlated well with the reactivity of the sorbents. Temperatures between 800 and 925{degree}C, and pressure between 12 and 25 bar, promoted an increase in reactivity, while the gas composition had no effect when changed from 15% CO{sub 2}, 3% O{sub 2}, 0.5% SO{sub 2}, balance N{sub 2} to 12% CO{sub 2}, 7% O{sub 2}, 0.5% SO{sub 2}, balance N{sub 2}. It was found that the unreacted shrinking core model could not satisfactorily describe the sulfation reaction under the conditions studied. The expression of ...
The objective of our research was to obtain fundamental information regarding the functional dependence of the diffusion coefficient of coal molecules on the ratio of molecule to pore diameter. That is, the objective of our study was to examine the effect of molecule size and configuration on hindered diffusion of coal macromolecules through as porous medium. To best accomplish this task, we circumvented the complexities of an actual porous catalyst by using a well defined porous matrix with uniform capillaric pores, i.e., a track-etched membrane. In this way, useful information was obtained regarding the relationship of molecular size and configuration on the diffusion rate of coal derived macromolecules through a pore structure with known geometry. Similar studies were performed using a pellet formed of porous alumina, to provide a link between the idealized membranes and the actual complex pore structure of real catalyst extrudates. The fundamental information ...
The 5'-terminal structures of human adenovirus type 2 (Ad2) early region 2 (E2) mRNA were investigated. The E2 transcription unit has several interesting properties, including the presence of a TATA-like...Full Text Available
The peak evaluation in alpha liquid scintillation is known to be easy, mostly due to the gaussian shape of the peaks. However, we often observed a high-energy tail in addition to a pure gaussian function. This effect is only detectable with a high resolution {alpha} liquid scintillation spectrometer such as the PERALS trademark system. Indeed, its intrinsic resolution (180 keV for a 4 MeV {alpha} particle) is better than that obtained for conventional LSC spectrometers. The peak asymmetry was quantified using the Fisher's coefficient {gamma}{sub 1} (symmetry factor). We show that the main effect responsible for the asymmetry is internal conversion. Indeed, most of the even-even nuclides have low {alpha} intensity transitions leading to excited levels of their daughter nuclides. The internal conversion is almost equal to 100% and consequently produces a sum peak at higher energy. No generalization is possible for ...
Long term integrated in situ experiments are performed in the HADES underground research facility (Mol, Belgium) in order to study the coupled reactivity between the different components of an underground repository for vitrified high level radioactive waste (HLW): glass, compacted clay, and stainless steel containers, at 90 degrees C and under gamma irradiation. Studies pertaining to the behaviour of silicon, a major element released during glass alteration, are presented here. Data collected from the integrated experiment, from simplified tests, and from modelling are put together, giving complementary information. The integrated experiment is used to investigate overall reactivity, whereas diffusion experiments coupled with modelling focused on the precipitation of silica in clay media. In the integrated in situ experiment, a bentonite clay (FoCa7) mixed with 5 wt.% of powdered glass frit was put in contact with U/Th-doped SON68 reference glass specimens for 1.2 years. One of the ...
Small circular and noncircular channels are representative of flow passages in compact evaporators and condensers. This paper describes results of an experimental study on heat transfer to the flow boiling of refrigerant- 12 in a small circular tube of diameter = 2.46 mm. The objective of the study was to assess the effect of channel size on the heat transfer coefficient and to obtain additional insights relative to the heat transfer mechanisms. The flow channel was made of brass and had an overall length of 0.9 m. The channel wall was electrically heated, and temperatures were measured on the channel wall and in the bulk fluid stream. Voltage taps were located at the same axial locations as the stream thermocouples to allow testing over an exit quality range of 0.21 to 0.94 and a large range of mass flux (63 to 832 kg/m{sup 2}s) and heat flux (2.5 to 59 kW/m{sup 2}). Saturation pressure was nearly constant, averaging 0.82 MPa for most of the testing; a few test ...
A rehabilitation programme for patients with conversion paralysis has been introduced in which they are offered physical rehabilitation. During an eight month period between October 1984 and May 1985...Full Text Available
... Title : Wear Rate and Friction Coefficient in Liquid Nitrogen and Hydrogen of Steel Sliding on Polymer Laminates (Various Fabrics and Polymers. ...
... Values of absorption maxima, X.nax, and associated molar extinction coefficients, c, as well as values of the n-octanol/water partition coefficient( ...
The diffusion coefficients (De) in bentonite were measured to understand and quantify the influence of groundwater chemistry such as ionic strength and to quantify the alteration of smectite mineralogical transformations. (author)
The first cohomology of the Virasoro algebra with coefficients in string fields are investigated. The relation between them and the Nambu-Goto action for a closed string is established. (orig.).
Lifetimes have been measured for a dipole band in {sup 139}Sm using DSAM. The deduced B(M1) and B(E2) values as well as B(M1)/B(E2) ratios are compared with calculations in the framework of the TAC (Tilted Axis Cranking) and SPAC (Shears mechanism with Principal Axis Cranking) models. The dipole band in {sup 139}Sm can be considered as a magnetic rotational band with a prolate or triaxial nuclear deformation. (orig.)
Lifetimes have been measured for dipole bands in {sup 142}Gd using DSAM. The deduced B(M1) and B(E2) values as well as B(M1)/B(E2) ratios are compared with calculations in the framework of the TAC (Tilted Axis Cranking) and SPAC (shears mechanism with Principal Axis Cranking) models. The dipole bands DB1 to DB4 can be interpreted as magnetic rotational bands. (orig.)
Intracervical application of prostaglandin E2 in the late first trimester induces (1) softening of the cervix tissue; (2) increase in sulfated glycosaminoglycans (18 +/- 12%, mean +/- SEM); (3) no change in hyaluronic acid and water; (4) decrease in pepsin-extractable collagen, and (5) apparent decrease in collagenase. A high activity of collagenase in combination with a replacement of collagen with sulfated glycosaminoglycans may be of importance for the ripening process.
The performance of a thermophotovoltaic (TPV) converter for solar energy is compared with that of direct solar energy conversion by silicon and germanium solar cells. The optical selectivity of an intermediate emitter is computed. Experimental results on selective emission, based on selectively emitting materials and on antireflection coatings on metals, are reported. For a TPV converter equipped with silicon solar cells, no selective emitter is found to yield better results than would be obtained by direct conversion. A TPV converter with germanium cells operating with a ThO/sub 2/-coated tungsten emitter, however, may achieve a conversion efficiency superior to that of direct solar energy conversion by either silicon or germanium solar cells.
A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)
Chorismate mutase, a branch-point enzyme in the aromatic amino acid pathway of Saccharomyces cerevisiae, and also a mutant chorismate mutase with a single amino acid substitution in the C-terminal part of the protein have been purified approximately 20-fold and 64-fold from overproducing strains, respectively. The wild-type enzyme is activated by tryptophan and subject to feedback inhibition by tyrosine, whereas the mutant enzyme does not respond to activation by tryptophan nor inhibition by tyrosine. Both enzymes are dimers consisting of two identical subunits of M_r 30,000, each one capable of binding one substrate and one activator molecule. Each subunit of the wild-type enzyme also binds one inhibitor molecule, whereas the mutant enzyme lost this ability. The enzyme reaction was observed by "1H NMR and shows a direct and irreversible conversion of chorismate to prephenate without the accumulation of any enzyme-free intermediates. The kinetic data of the ...
Aerosol and gas measurements were made with the University of Minnesota Mobile Laboratory (UMML) during the VISTTA programme near Page, Arizona. The UMML was stationed on Zilnez Mesa approx. 65 km east of the Navajo coal-fired power plant. Measurements were made both in and out of the power plant plume and were made during the day and night. Measured parameters included aerosol size distributions, Aitken nuclei count, ozone and sulphur dioxide concentrations, the aerosol light scattering coefficient, and meteorological parameters including ultraviolet radiation intensity. Concentrations of NO and NO/SUB/x were occasionally measured. Data show clear evidence of gas-to-particle conversion in the plume with aerosol volume being added in the 0.01 MUm - 0.32 MUm dia. range and new particles being formed. The observed excess aerosol volume depends strongly upon the SO/SUB/2 concentrations and the time of day with none observed in plume parcels which ...
Thermo-reactive diffusion chromizing followed by pulsed plasma nitriding were carried out on AISI 52100 and 8620 bearing steels. The chromized samples were pulse-plasma nitrided for 5 h at 500 deg. C in various N_2-H_2 gas mixtures. The coated steels were characterized using scanning electron microscopy, X-ray diffraction and microhardness testing. The unlubricated wear behaviors of only chromized and duplex treated steels were investigated in ball-on-disc system tests at room temperature. X-ray diffraction patterns of the duplex treated samples containing H_2 indicated the formation of dominant CrN and Cr_2N nitrides as well as the formation of Cr_3C_2 and Cr_7C_3 carbides. Gas mixtures in the plasma nitriding, which was performed after chromizing, have a significant influence on the wear rate of the duplex treated steels. The wear and friction tests showed that the lowest friction coefficient and wear rates were observed for the samples duplex treated in a 50%N_2 ...
Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging ...
The radial distribution function and the second virial coefficient of interacting bosons have been studied. The second virial coefficient has been deduced theoretically and is in good agreement with experimental values. The third virial coefficient has been calculated from the experimental values of the pressure. (Auth.).
A linear diffusion model serves as the basis for determination of an effective radon diffusion coefficient in concrete. The coefficient was needed to later allow quantitative prediction of radon accumulation within and behind concrete walls after application of an impervious radon barrier. A resolution of certain discrepancies noted in the literature in the use of an effective diffusion coefficient to model diffusion of a radioactive gas through a porous medium is suggested. An outline of factors expected to affect the concrete physical structure and the effective diffusion coefficient of radon through it is also presented. Finally, a field method for evaluating effective radon diffusion coefficients in concrete is proposed and results of measurements performed on a concrete foundation wall are compared with similar published values of gas diffusion coefficients ...
The diffusion coefficient of particles in radioactive gases has been calculated with account of random wandering of aerosols (occurrence of local fields affecting the particles; recoils accompanying radiation emitted by particles, etc.). To determine the diffusion coefficient, the method of Fokker-Planck equation derivation was used. A formula is presented for calculating the radiation-stimulated diffusion coefficient. A linear growth of the diffusion coefficient with radioactivity is noted according to the formula, the diffusion coefficient is mainly determined by the field in the radiation damage region. The aerosol radioactivity may result in a more rapid deposition of aerosols in the pipelines and aerosol purification systems. The diffusion rate grows not only in the presence of intrinsic radioactivity but in case of external radiation exposure as well.
An experimental study and a theoretical simulation were made of stimulated Raman scattering (SRS) conversion into shifted components. It was found that there were optimal values of the pressure and focal distance for conversion into the first 'blue' satellite of the first Stokes component. A study was made of the spatial and temporal dynamics of SRS conversion, which took into account generation of the shifted components. It was demonstrated theoretically and experimentally that the satellite intensity could be enhanced significantly by additional electron-collision excitation of the vibrational levels in the conversion medium or by the application of pairs of pump pulses. The maximum efficiency of conversion to the first 'blue' satellite of the first Stokes component was 10% and the satellite intensity reached one-third of the intensity of the main Stokes line. (nonlinear optical ...
Cell surface glycosaminoglycans play important roles in cell adhesion and viral entry. Laboratory strains of two alphaviruses, Sindbis and Semliki Forest virus, have been shown to utilize heparan sulfate as an attachment receptor, whereas Ross River virus (RRV) does not significantly interact with it. However, a single amino acid substitution at residue 218 in the RRV E2 glycoprotein adapts the virus to heparan sulfate binding and expands the host range of the virus into chicken embryo fibroblasts. Structures of the RRV mutant, E2 N218R, and its complex with heparin were determined through the use of electron cryo-microscopy and image reconstruction methods. Heparin was found to bind at the distal end of the RRV spikes, in a region of the E2 glycoprotein that has been previously implicated in cell-receptor recognition and antibody binding.
In areas where radiation dose monitoring has not been performed, it is essential to use material available in the environment be able to rapidly assess doses to individuals for immediate emergency medical care or for general estimation of the radiological consequences. It was shown that certain types of telephone cards containing microchips have the potential to be used as individual radiation dosimeters in emergency situations to detect doses over 250 mGy by luminescence measurements. In order to understand the dosimetric properties of chip cards, the components obtained from INFINIEON Company at various stages of production were used for luminescence measurements. It is found that the protecting layer used above the chips so called 'globe top' is the main source of radiation induced signal in chip cards. The globe top produced by INFINIEON at that stage is found to contain SiO2 and Epoxy. In order to improve the dosimetric properties of the chip cards, the raw material of the globe ...
as for direct energy conversion in specialized direct electrical energy conversion plants. Figure 1. An energetic (~163KeV) proton and a 11boron nucleus fuse ...
Activation-induced deaminase (AID) initiates somatic hypermutation, gene conversion and class switch recombination by deaminating variable and switch region DNA cytidines to uridines. AID is predominantly...Full Text Available
A schematic diagram of the decision making process for air pollution control equipment for the conversion of a fossil-fired generating unit from oil to coal is presented and explained.
In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion ...
Mutational inactivation of the RB1 tumor suppressor gene initiates retinoblastoma and other human cancers. RB1 protein (pRb) restrains cell proliferation by binding...Full Text Available
In response to oxidative stress, the transcription factor NF-E2-related factor 2 (Nrf2) controls the fate of cells through transcriptional upregulation of antioxidant response element (ARE)-bearing...Full Text Available
While estrogen (E2) is thought to play an important role in age-related cognitive decline, neuronal plasticity, as well as the pathogenesis of Alzheimer disease (AD), the mechanisms by which...Full Text Available
A sensitive assay based on the polymerase chain reaction for the detection of Ockelbo virus RNA was developed. Two primer pairs from the gene coding for the E2 glycoprotein were chosen. By use of a...Full Text Available
Ligature-induced periodontitis was monitored for 6 months in eight Macaca mulatta monkeys to examine clinical status, radiographic bone level, and crevicular fluid (CF) levels of prostaglandin E2 (PGE2),...Full Text Available
The Eighth Indirect Liquefaction Contractors' Review Meeting was held November 15-17, 1988 at the Pittsburgh Hyatt Hotel. Twenty-eight presentations were made by contractors, invited speakers, and Pittsburgh Energy Technology Center R and D personnel. Six areas of research were covered: synthesis gas conversion to oxygenates; light hydrocarbon gas conversion; slurry reactor hydrodynamics; production, clean-up and conversion to hydrocarbon fuels; Fischer-Tropsch products upgrading; and, synthesis gas bioconversion. The meetings also included a panel discussion on direct methane conversion research. Individual projects are processed separately for the data bases.
The invention concerns the conversion of steam turbines, particularly condensation turbines, for the economic coupling of process steam and heating steam. The conversion occurs by retaining the basic construction of foundations, housing and bearings as support group and coupling member and matching the specially developed construction for the idea of use into the existing housing, and inserting the rotor into the shaft unit. By having the unchanged supports of the housing and the bearings of the shaft unit, the elasticity in expansion and the vibration behaviour of the turbine are retained and the conversion costs can be lowered.
Conversion of the United States military to the International System of measurement units is in the very early stages. Little formal planning has been done to articulate the management required to complete the conversion of operational Army and Air Force units. For those operational forces tasked to provide continuous combat readiness throughout metrication, management problems associated with the conversion are particularly difficult because of the nature of these assigned missions. This is the case for the 82nd Airborne Division ready brigade force (DRB) and the Military Airlift Command (MAC) strategic airlift system operating the C-141 and C-5A aircraft.
The release of {sup 222}Radon to the atmosphere is controlled by the rate of its gas transport through earthen materials. Of the many soil-related parameters, radon diffusion coefficient is the key parameter that characterizes this transport. We compared the radon diffusion coefficients measured at the laboratories for the UMTRA Project with simple empirical correlations developed by others. The empirical correlations predict the radon diffusion coefficient based on the fraction of moisture saturation and porosity. One of the more recent correlations agrees reasonably well with the measurements. In addition, by using a series of correlation curves, we studied the empirical relationships of the. radon diffusion coefficient with the saturated hydraulic conductivity, the fines content, and the moisture saturation in soil. The results reveal that a reliable determination of the long-term moisture and ...
Radon migration in porous, earthen materials is characterized by diffusion in both the air and water components of the system as well as by the interaction of the radon between the air and water. The size distribution and configuration of the pore spaces and their moisture distributions are key parameters in determining the radon diffusion coefficient for the bulk material. A mathematical model is developed and presented for calculating radon diffusion coefficients solely from the moisture content and pore size distribution of a soil, reducing the need for resorting to radon diffusion measurements. The resulting diffusion coefficients increase with the median pore diameter of the soil and decrease with increasing widths of the pore size distribution. The calculated diffusion coefficients are suitable for use in simple homogeneous-medium diffusion expressions for predicting radon transport and compare ...
Electron scattering data have been used to obtain transition charge densities for the low-lying E2 transitions in /sup 88/Sr, /sup 89/Y, and /sup 90/Zr. These charge densities show a characteristic shape indicative of their microscopic constituency, modified by core-polarization effects. A good description of transitions in the even-even nuclei is obtained by using the measured single-particle transitions in /sup 89/Y as effective densities. .ID LV2086 .PG 19 22
Microscopic non-energy weighted sum-rules for the total rates of the neutrinoless ..mu..-e conversion process are constructed in the frame of the shell model for closed shell nuclei. For non-closed shell nuclei the relevant rates were obtained by interpolation. Also the contribution of the coherent process to the total ..mu..-e conversion rate is calculated and discussed.
The work of the study group for coal conversion by hydrogenation (G.E.C.H.) is an example of well concerted association between research laboratories (CNRS, Ecole des Mines...) and directly interested industrial research centers, (CERCHAR, G d F, IFP). This paper presents the activities of G.E.C.H. in the field of coal conversion by hydroliquefaction.
The lepton flavor-violating coherent ( /sup -/, e/sup -/) conversion is investigated. Photonic and nonphotonic contributions arising in various gauge models are considered. The dependence of the conversion rate on the structure of the nucleus is given by the elastic form factors. These are obtained in the context of shell model taking into account finite-size effects or extracted from the electron scattering data whenever possible. The relevant branching ratios are studied throughout the periodic table.
This current awareness bulletin announces on a semimonthly basis the current worldwide information entered into the Energy Data Base on all aspects of direct energy conversion. Categories include photovoltaic conversion, magnetohydrodynamic generators, electrohydrodynamic generators, thermoelectric generators, thermionic converters, fuel cells, and miscellaneous converters. An abstract is inclluded with each citation. (WHK)
Thermophotovoltaic energy conversion achieves direct conversion of thermal energy to electricity without the need for complex dynamic machinery operating in one of several possible thermodynamic cycles. This paper presents an analysis of a hybrid solar thermophotovoltaic (STPV) energy conversion system in which a receiver/photovoltaic (PV) array subsystem is powered by either a solar concentrator or a fossil fuel combustion source. The overall TPV system efficiency is calculated using an appropriate selective emitter and a spectrally tuned solar cell designed to achieve maximum conversion efficiency in the narrow band emitted by the selective emitter. Two limiting cases are examined to place upper and lower bounds on system performance. The estimates of system performance are based on actual experimental data from PV cells and selective emitters.
The factors determining temperature and current coefficients of lasing wavelength are investigated and discussed under monitoring CO2-gas absorption spectra. The diffusion rate of...Full Text Available
Available data are presented which support the supposition that metals and alloys with a negative low-temperature Hall coefficient are apparently not superconducting. (author).
Reliable values of x-ray and gamma-ray attenuation coefficients of elements and compounds are required in spectrometry as well as in many other scientific, engineering and medical disciplines involving photon radiation
An elliptic equation in a rectangle with coefficients depending on a fast variable and with its period being a small parameter is considered. An asymptotic expansion of the solution up to an arbitrary degree of the small parameter is constructed and substantiated by applying the two-scale expansion method.
The problem of optimizing a horn radiator of electromagnetic waves for the reflection coefficient and the coefficient of transformation of the fundamental mode into higher order modes is solved. Optimization is performed by means of selecting a combined shape of the radiator generatrices.
Bioethanol is among the most promising of biofuels that can be produced from different biomass such as agricultural products, waste and byproducts. This paper reported on a study that examined the energy conversion of different groups of biomass to bioethanol, including lignocelluloses, starches and sugar. Biochemical conversion generally involves the breakdown of biomass to simple sugars using different pretreatment methods. The energy needed for the conversion steps was calculated in order to obtain mass and energy efficiencies for the conversions. Mass conversion ratios of corn, molasses and rice straw were calculated as 0.3396, 0.2300 and 0.2296 kg of bioethanol per kg of biomass, respectively. The energy efficiency of biochemical conversion of corn, molasses and rice straw was calculated as 28.57, 28.21 and 31.33 per cent, respectively. The results ...
The temperature coefficient has been investigated on the Wolsung nuclear power reactor, in which fuel is natural uranium dioxide and moderator heavy water. The numerical computations are carried out in terms of changes of the effective neutron multiplication factor with respect to fuel, moderator, and coolant temperatures. Those results are compared with the computed values of temperature coefficient based on the LATREP computer code. (author).
The algebra of the coefficients in the minimal representation of the A_n_-_1 quantum group, discussed by Felder and Varchenko, is given. Those coefficients are associated with the Boltzmann weights of A_n_-_1"("1") interaction-round-a-face model. The authors show that the algebra satisfies the Yang-Baxter equation. The PBW base for this algebra is also given
Fermilab is the US Tier-1 Center for CMS data storage and analysis. End-2-End (E2E) circuits are utilized to support high impact data movement into and out of the Tier-1 Center. E2E circuits have been implemented to facilitate the movement of raw experiment data from the Tier-0 Center at CERN, as well as processed data to a number of the US Tier-2 sites. Troubleshooting and monitoring of those circuits presents a significant challenge, since the circuits typically cross multiple research & education networks, each with its own management domain and customized monitoring capabilities. The perfSONAR Monitoring Project was established to facilitate development and deployment of a common monitoring infrastructure across multiple network management domains. Fermilab has deployed perfSONAR across its E2E circuit infrastructure and enhanced the product with several ...
Starting from the original collective Hamiltonian of Bohr and separating the beta and gamma variables as in the X(5) model of Iachello, an exactly soluble model corresponding to a harmonic oscillator potential in the beta-variable (to be called X(5)-$\\beta^2$) is constructed. Furthermore, it is proved that the potentials of the form $\\beta^{2n}$ (with n being integer) provide a ``bridge'' between this new X(5)-$\\beta^2$ model (occuring for n=1) and the X(5) model (corresponding to an infinite well potential in the beta-variable, materialized for n going to infinity. Parameter-free (up to overall scale factors) predictions for spectra and B(E2) transition rates are given for the potentials $\\beta^2$, $\\beta^4$, $\\beta^6$, $\\beta^8$, corresponding to E(4)/E(2) ratios of 2.646, 2.769, 2.824, and 2.852 respectively, compared to the E(4)/E(2) ratios of 2.000 ...
Oxidation of propylene with oxygen, air and a mixture of nitrogen?oxygen in a barrier discharge is investigated. The selectivity towards formation of propylene oxide in pure oxygen is shown to be as high as 45 wt% and the propylene conversion ratio is found to be 12.9 wt%. In the oxidation with air, the propylene oxide selectivity is 23 wt%, while the conversion is 7.5 wt%. The values of propylene conversion and selectivity towards formation of propylene oxide in a barrier discharge are consistent with those obtained by the thermocatalytic methods for production of propylene oxide.
This paper presents the results of a study commissioned by the British Columbia Science Council to identify opportunities for liquefaction of B.C. coals and to recommend effective approaches to the development of a research program on coal conversion. Contains reviews of British Columbia coal resources to identify prospective candidates for conversion to liquid fuels; of the state of the art in the various processes for the conversion of coal to liquid fuels with particular emphasis on those processes most relevant to British Columbia applications; and of research opportunities in British Columbia for the development of coal liquefaction technology. (16 refs.)
Red mud, and red mud activated by dissolution in hydrochloric acid and reprecipitation with ammonia, were tested as catalysts for the hydrogenation of an anthracene oil in a trickle-bed reactor. Conversion data were determined for the different polyaromatic compounds in the anthracene oil. Red mud shows appreciable catalytic activity, which is enhanced by the activation. Although both red mud and activated red mud are less active than a commercial Ni-Mo/[gamma]-alumina hydrotreating catalyst, the difference in activity is smaller when conversion to hydroaromatics instead of total conversion of reactants is considered. 20 refs., 8 figs., 3 tabs.
Physical processes in the region of laser conversion for the next Linear Colliders (NLC) are discussed. The main goal of this conversion is to obtain high-energy intense #gamma# beams for #gamma#e and #gamma##gamma# colliders. This conversion has important by-products: (i) one can observe here effect of nonlinear QED (in a strong external field)-production of e"+e"- pairs by a high-energy photon and emission of very high-energy photons by an electron; (ii) one can produce and observe here the invisible axion in colliding #gamma#_0e beams. The NQED effects also result in variation of the spectra of high-energy photons and an additional background. 12 refs., 12 figs., 1 tab.
Because of its direct energy conversion techniques, AMTEC is the front runner today. However, because these systems are now only in the preliminary design ...
Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam-cycle is the conventional conversion method; however total energy conversion efficiencies for this type of process are only slightly over 30%. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40%. Conversion processes based on gasification offer efficiencies above 50%. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. This process is concerned with the removal of H{sub 2} from coal gas through an electrochemical membrane technology.
Apparatus and method are described for the vaporization of liquid fuel oils to produce a gaseous mixture suitable for burning in a burner normally designed for operation utilizing natural gas.
BackgroundMutations that disrupt the conversion of prelamin A to mature lamin A cause the rare genetic disorder Hutchinson-Gilford progeria syndrome and a group of laminopathies....Full Text Available
This volume contains the corporate author index, author index, and subject index for publications entered into the IEA Biomass Conversion Technical Information System during the year 1987. (DT)
... This is the case for the 82nd Airborne Division ready brigade force (DRB) and the Military Airlift Command (MAC) strategic airlift system operating ...
This volume contains the corporate author index, author index, and subject index for publications entered into the IEA Biomass Conversion Technical Information System during the year 1986. (DT)
Manganese toxicity can cause a neurodegenerative disorder affecting cortical and basal ganglia structures with a neurological presentation resembling features of Parkinson's disease. Children are more sensitive to Mn-induced neurological dysfunction than adults, and recent studies from our laboratory revealed a marked sensitivity of male juvenile mice to neuroinflammatory injury from Mn, relative to females. To determine the role of estrogen (E2) in mediating sex-dependent vulnerability to Mn-induced neurotoxicity, we exposed transgenic mice expressing an NF-kB-driven enhanced green fluorescent protein (EGFP) reporter construct (NF-kB-EGFP mice) to Mn, postulating that supplementing male mice with E2 during juvenile development would attenuate neuroinflammatory changes associated with glia...
A Final Environmental Impact Statement (FEIS) related to the licensing of Envirocare of Utah, Inc.`s proposed disposal facility in Tooele county, Utah (Docket No. 40-8989) for byproduct material as defined in Section 11e.(2) of the Atomic Energy Act, as amended, has been prepared by the Office of Nuclear Material Safety and Safeguards. This statement describes and evaluates the purpose of and need for the proposed action, the alternatives considered, and the environmental consequences of the proposed action. The NRC has concluded that the proposed action evaluated under the National Environmental Policy Act of 1969 (NEPA) and 10 CFR Part 51, is to permit the applicant to proceed with the project as described in this Statement.
This report summarises nearly 20 biosphere reports and gives a synthesis of the work performed within the SR-Site Biosphere project, i.e. the biosphere part of SR-Site. SR-Site Biosphere provides the main project with dose conversion factors (LDFs), given a unit release rate, for calculation of human doses under different release scenarios, and assesses if a potential release from the repository would have detrimental effects on the environment. The intention of this report is to give sufficient details for an overview of methods, results and major conclusions, with references to the biosphere reports where methods, data and results are presented and discussed in detail. The philosophy of the biosphere assessment was to make estimations of the radiological risk for humans and the environment as realistic as possible, based on the knowledge of present-day conditions at Forsmark and the past and expected future development of the site. This was achieved by using the ...
The quantitative measurement of carbon concentration-distance curves serves as fundamental prerequisite for the evaluation of rim zone properties connected with decarburisation processes in material science. This was shown in part 1 of the present work with two samples from through-hardenable rolling bearing steel 100Cr6 (SAE 52100) austenitised in different oxidising atmospheres by position dependent determination of hardness, residual stresses, and X-ray line broadening ({l_brace}211{r_brace} {alpha}'-Fe diffraction line). In practice, it is important to predict carbon concentration-distance curves under prevailing heat treatment conditions or to conclude conversely from profile measurements. Based on a refined kinetics model of a diffusion-controlled process, part 2 therefore presents a simulation tool developed by means of the finite element method (FEM). Apart from the concentration dependence of the diffusion coefficient, it also ...
In the latter half of 2005, the U.S. Environmental Protection Agency (USEPA) published a Proposed Rule (40 CFR Part 197) for establishing a dose rate standard for limiting radionuclide releases from the proposed Yucca Mountain high-level radioactive waste repository during the time period from 10{sup 4} to 10{sup 6} years after closure. The proposed standard was based on the difference in the estimated total dose rate from natural background in the Amargosa Valley and the ''average annual background radiation'' for the State of Colorado. As defined by the USEPA, ''natural background radiation consists of external exposures from cosmic and terrestrial sources, and internal exposures from indoor exposures to naturally-occurring radon''. On the basis of its assessments, the USEPA estimated that the difference in the dose rate in the two identified areas was 3.5 mSv y{sup -1}. The purpose of this review was to provide ...
The following paper is focused on the numerical modelling of the transient radon diffusion through radon-proof membranes during the measurement of their radon diffusion coefficient. The major aim of such numerical modelling is to increase the accuracy of radon diffusion coefficients derived from the measured data sets. The developed complex ''transient'' numerical model is able to calculate the radon diffusion coefficient with sufficient accuracy from almost any data set - even from a short-time measurement with a non-linear course of results. This numerical model can also be used for various analyses of transient radon transfer processes (e.g. for the calculation of radon distribution curves within the membrane). The following paper presents governing equations for the simulation model, together with a brief description of algorithms incorporated in the newly developed software package, ...
A thermodynamic model for predicting the distribution coefficients has been developed by taking into account the extraction mechanism and the chloride complexation when Sm, Eu, Gd, Tb, Dy and Ho for single component systems are extracted from acidic chloride solutions by di-2-ethylhexyl ester in kerosene, respectively. The model equation includes two constants, of which one corresponds to the apparent extraction equilibrium constant and the other is due to the variation of the activity coefficients of organic species. These values are determined from a few experimental data by the curve fitting method. Then, the distribution coefficients under untried calculations, Bromley's formulation is used to estimate the activity coefficients of aqueous species and the interaction parameters for some rare earth chlorides are reported in terms of morality and molarity using data from Spedding et al. According to ...
Most wind farms consist of horizontal axis wind turbines (HAWTs) due to the high power coefficient (mechanical power output divided by the power of the free-stream air through the turbine cross-sectional area) of an isolated turbine. However when in close proximity to neighboring turbines, HAWTs suffer from a reduced power coefficient. In contrast, previous research on vertical axis wind turbines (VAWTs) suggests that closely spaced VAWTs may experience only small decreases (or even increases) in an individual turbine's power coefficient when placed in close proximity to neighbors, thus yielding much higher power outputs for a given area of land. A potential flow model of inter-VAWT interactions is developed to investigate the effect of changes in VAWT spatial arrangement on the array performance coefficient, which compares the expected average power coefficient of turbines in an ...
Radon emanation coefficients of 0.02 to 0.55 were measured at moisture contents ranging from dry to saturation in 18 different ores. The emanation coefficients rose from a minimum when dry to a plateau usually starting at 5 to 20 percent of saturation. A model, using measured pore-size distributions, suggested that the radium mineralization may be confined to annular layers about 0.02 micrometers thick around pores. Radon's diffusion coefficient was determined as a function of moisture. The techniques involved comparing a disk's exhalation as a function of time whether or not the disk had a distributed source. The model was free of approximations and included the effects of porosity and adsorption. An increase of diffusion coefficient with moisture for one or two ores was explained in terms of a model's equation for the diffusion coefficient in terms of ...
Transverse glow discharges in supersonic air and methane flows are studied both experimentally and theoretically. The experiments show that a diffuse volume discharge filling the whole cross section of the flow can easily be initiated in air, whereas a diffuse discharge in a methane flow shows a tendency to transition into a constricted mode. The electron transport coefficients (mobility and drift velocity) and the kinetic coefficients (such as collisional excitation rates of the vibrational levels of a methane molecule, as well as dissociation and ionization rates) are calculated by numerically solving the Boltzmann equation for the electron energy distribution function. The calculated coefficients are used to estimate the parameters of the plasma and the electric field in the positive co...
In order to increase the sensitivity of photometric determination of tungsten and to find forms with high molar extinction coefficients, mixed-ligand complexes of tungsten with antipyrine and trihydroxyfluorone have been studied. The molar extinction coefficients have been determined for chloride associates of mixed-ligand complexes containing different trioxyfluorones: phenylfluorone, salicylflourone, p-bromphenylfluorone, anthrafluorone, dioxyfluorescein, and dioxyfluoroscein ethylate (DOFE). An associate formed by DOFE has the maximum molar extinction coefficient. It has been used for photometric determination of microgram amounts of tungsten impurity in vanadyl sulphate.
This paper focuses on the design and modeling of the humidification dehumidification desalination (HDH) process. The process is only found on experimental or very small pilot scale. Literature studies are rather limited and it includes a number of experimental investigations, performance evaluation, and measurements of the heat and mass transfer coefficients. This study includes useful and new data on the evaluation of the heat transfer coefficient of the humid air stream in the condenser unit. The analysis develops a correlation for the heat transfer coefficient for the humid air stream as a function of the Reynolds and Prandtl numbers. Also, detailed evaluation of the system performance is presented as a function of the system temperatures and the inlet relative humidity of the air strea...
The present paper dealt with the extension of tendon friction coefficient correlation as a function of loading end load and circumferential angle, proposed in the former paper. The extended correlation further included the effects of the number of strands contacted with sheath, tendon diameter, politicization of tendon and tendon local curvature. The validity of the correlation was confirmed by several published measured data. The structural analysis of middle cylinder part of 1/4 PCCV (Prestressed Concrete Containment Vessel) model was conducted using the present friction coefficient correlation. The results were compared with the analysis using constant friction coefficient, focused on the tendon tension force distribution. (author)
Hitherto in this laboratory, ionization coefficients alpha and attachment coefficients #eta# have been determined from Townsend's discharge experiments by a curve-fitting method. However, the method proved to be laborious, Formulae have been derived in this paper to give value of alpha and #eta# as a function of Isubo, Isub1 and Isub2 where Isubo is the photoelectric current at a gap setting d and Isub2 the current at another gap setting 2 d. The values of alpha and #eta# obtained give currents in agreement to within 3% in the best cases with the observed currents.
This paper first introduces the calculating method of radium specific activity to determine the radon emanation rate of tailing of uranium mine No. 794, the method needs two parameters: radon emanation coefficient and radon diffusion coefficient. According to the measured results of parameters and the contrast between radium specific activity of indoor chemical analysis of field sample and field gamma-ray spectra, the authors discuss the variation rules and characteristics of radon emanation coefficient and radon diffusion coefficient, and the best climate and seasons for measuring these parameters in northern China, and finally summarize the characteristics of this method through analyzing measured results. (authors)
Reactive Magnetron Sputtering is a complex process and huge efforts are made addressing the understanding of its fundamental phenomena and the simulation of the deposition process by e.g. Particle in Cell/Monte Carlo (PIC/MC). One of the most uncertain parameters in this reactive sputtering process is the incorporation coefficient of the reactive gas in the growing layer, i.e. the real-time sticking coefficient during deposition. In this work, mass spectrometry is used to deliver more insights on this complex matter. Earlier, a method was developed to determine the incorporation coefficient of the reactive gas molecules in the growing metal film, using mass spectrometry combined with thin film analysis techniques (electron probe microanalysis and x-ray photoelectron spectroscopy). This method delivers a global, realistic incorporation coefficient which can be used in models for the reactive sputtering ...
The hydraulic characteristics of flow control multiorifice plate assemblies designed for the FFTF reactor were investigated. The pressure drop flowrate characteristics determined in the test are presented. (JWR)
In terms of the reduced potential energy barrier ? = ?uTS/kT, the rate coefficients for chemical reactions are usually expressed as proportional to e-?. The coupling between vibrational modes of the medium to the reaction coordinate leads to a proportionality of the regularized gamma function of Euler Q(a,?) = ?(a,?)/?(a), with a being the number of modes coupled to the reaction coordinate. In this work, the experimental rate coefficients at various temperatures for several chemical reactions were fitted to the theoretical expression in terms of Q(a,?) to determine the extent of its validity and generality. The new expression affords lower deviations from the experimental points in 29 cases out of 38 and it accounts for the curvature in the logarithmic plots of rate coefficients versus inverse temperature. In the absence of tunneling, conventional theories predict the curvature of these plots to be identically zero.
coupled heat/mass transfer Stefan problem. Taking the diffusion coefficient of Bi as a free parameter, the best fit was observed for the published value, ...
This paper proposes an adaptive morphological dilation image coding with context weights prediction. The new dilation method is not to use fixed models, but to decide whether a coefficient needs to be dilated or not according to the coefficient's predicted significance degree. It includes two key dilation technologies: 1) controlling dilation process with context weights to reduce the output of insignificant coefficients, and 2) using variable-length group test coding with context weights to adjust the coding order and cost as few bits as possible to present the events with large probability. Moreover, we also propose a novel context weight strategy to predict coefficient's significance degree more accurately, which serves for two dilation technologies. Experimental results show that our proposed method outperforms the state of the art image coding algorithms available today.
We prove a generalization of the Verlinde formula to fermionic rational conformal field theories. The fusion coefficients of the fermionic theory are equal to sums of fusion coefficients of its bosonic projection. In particular, fusion coefficients of the fermionic theory connecting two conjugate Ramond fields with the identity are either one or two. Therefore, one is forced to weaken the axioms of fusion algebras for fermionic theories. We show that in the special case of fermionic W(2, #delta#)-algebras these coefficients are given by the dimensions of the irreducible representations of the horizontal subalgebra on the highest weight. As concrete examples we discuss fusion algebras of rational models of fermionic W(2, #delta#)-algebras including minimal models of the N = 1 super Virasoro algebra as well as N = 1 super W-algebras SW(3/2, #delta#). (orig.).
Even when a healthy individual is studied, his/her erythrocytes in capillaries continually change their shape in a synchronized erratic fashion. In this work, the problem of characterizing the cell...Full Text Available
Summary Analyses of event runoff coefficients provide essential insight on catchment response, particularly if a range of catchments and a range of events are compared by a single indicator. In this study we examine the effect of climate, geology, land use, flood types and initial soil moisture conditions on the distribution functions of the event runoff coefficients for a set of 14 mountainous catchments located in the eastern Italian Alps, ranging in size from 7.3 to 608.4km2. Runoff coefficients were computed from hourly precipitation, runoff data and estimates of snowmelt. A total of 535 events were analysed over the period 1989-2004. We classified each basin using a "permeability index" which was inferred from a geologic map and ranged from "low" to "high permeability". A continuous s...
... 5.9-585/T; thermal stability; solubility in liquid nitrogen, oxygen and Freons; molar extinction coefficients in the visible range and EPR spectrum. ...
Radon proof barriers are used for lowering of radon transport from the soil into the house and the determination of the radon diffusion coefficient is an important parameter to be determined in order to design the minimal thickness of the radon proof insulation. A method has been developed in our laboratory by using modified Lucas cells connected to a radon source and tightly closed onto the top by the tested membranes whose radon diffusion coefficients are being measured. Solving the time-dependent differential equation for radon diffusion in the membrane for well-defined experimental conditions the effective radon diffusion coefficient of the insulating material can be evaluated by comparing the radon concentration decrease in the cell for the first hours with the well-known radioactive decay. First results obtained in several preliminary tests carried out with a parafilm M barrier and two polyethylene membranes are shown ...
Mar 1, 2011 ... Molar extinction coefficients of hydrogen iodide in the Schumann region. Author: De More, W. B.; Raper, O. F.. Abstract: Molar extinction ...
An experimental study of second harmonic generation in a copper-vapor pulsed laser with an ADP crystal is presented. The ratio of the conversion into the second harmonic is found to depend on the average power of the exciting radiation. The maximum conversion ratio was 8.5%. Thermal self-defocusing is the main obstacle to obtaining high average powers at the double frequency.
The IAEA Department of Safeguards established a project in 1996 for the year 2000 (Y2K) conversion activities. This project covered assessment, conversion and testing of the software applications, instrument evaluation software, embedded systems and Personal Computer (PC) hardware attached to various equipment. Significant progress has been made in converting the applications and instruments to be year 2000 compliant. At the same time Member states have made an effort as well in converting the systems used jointly at the facilities
This is the June report by the Energy Information Administration. The contents of the report include an energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy. Included are appendices containing thermal conversion factors, metric and other physical conversion factors, and carbon dioxide emission factors for coal.
The catalytic performance of alkaline-treated zeolite H-ZSM-5 in the conversion of methanol to gasoline has been studied. After treatment with 0.20M NaOH, the total conversion capacity increased by a factor of 3.3, and the selectivity towards the gasoline fraction increased by a factor of 1.7. Physical characterization indicated the formation of mesopores and improved crystallinity.
Using the experimentally determined cutoff energies of the muon-electron and the pion-electron conversion curves in a tachyon-bradyon model of the electron and the muon, the magnetic moments of these particles have been derived and found to be the Bohr magnetons identically. The tachyons, being bound to the bradyons and unable to drop below the speed of light, cause the bradyons to revolve in an orbit. It is this orbital motion of the charged bradyons that generates the magnetic moments.
This paper reports the effectiveness of solvents on the liquefaction of 11 different Turkish lignites investigated by using tetralin, creosote, and anthracene oils. The highest total conversions were obtained with tetralin. The catalytic effects of CoMo and red mud were compared by using creosote oil as the solvent. It was found that red mud catalyzed mainly the asphaltene formation reaction for the given experimental conditions. The additional of CoMo significantly catalyzed the liquefaction reaction, thus increasing the lignite conversion and oil formation.
The aim of the paper is brief description of the present state and main results of investigations on the direct energy conversion (EC). The following EC development directions are considered: thermoelectric EC, thermionic EC, thermophotovolt EC, magnetohydrodynamic-dynamic EC, nuclear-optical EC, plasma-chemical EC and electrochemical EC (hydrogen power engineering
This book deals specifically with the development of new processes of converting coal into useful chemical feedstocks. The major topic in this volume is the generation of syngas and its catalytic conversion to chemicals via the Fischer-Tropsch synthesis. Describes processes involved in conversion, recent catalytic developments, and the commercially important Sasol process. Also includes chapters on the carbide process and potential of future developments in the field.
This thesaurus contains the vocabulary used to index the Biomass Database maintained by the IEA Biomass Conversion Technical Information Service. The database, which is used to produce Biomass Abstracts, contains indexed and abstracted references to the published literature relating to biomass energy including cultivations, harvesting, materials handling, conversion techniques, environmental aspects and economics.
The catalytic liquefaction of a Chinese bituminous coal was simulated by artificial neural network. Three liquefaction variables, catalyst loading, reaction temperature and reaction time were used as inputs and tetrohydrofuran (THF) conversion and toluene (T) conversion were used as outputs. The artificial neural network, trained by the experimental data, could represent the liquefaction process, with a mean squared deviation of less than 0.025. 7 refs.,1 fig., 3 tabs.
Ozsvath and Szabo show that there is a spectral sequence whose E^2 term is the reduced Khovanov homology of L, and which converges to the Heegaard Floer homology of the (orientation reversed) branched double cover of S^3 along L. We prove that the E^k term of this spectral sequence is an invariant of the link L when k>2. If L is a transverse link, then we show that Plamenevskaya's transverse invariant gives rise to a transverse invariant of L in each of these higher terms.
The experiences are described of the examination of orbita in children using computer tomography (CT). Over a period of four years 42 examinations were performed of children in the age ranging between 7 months and 15 years, i.e., 2.7 percent of all CT examinations performed. The highest diagnostic yield was in orbita tumours. The possibilities of CT are demonstrated on examples.
Glycyrrhiza glabra root is one of the common traditional Chinese medicines and used as flavoring and sweetening agents for tobaccos, chewing gums, candies, toothpaste and beverages. While glycyrrhizin is one of the main components in the extract of G. glabra root and has been characterized, the other components have not been well characterized. The mechanism of growth activation of breast cancer MCF-7 cells, including the activation of Erk1/2 and Akt, and the transcriptional regulation of estrogen-responsive genes, was examined by means of sulforhodamine B, luciferase reporter gene, real-time RT-PCR and Western blotting assays after the induction of the cells with the extract of G. glabra root. The extract has similar activity to that induced by 17beta-estradiol (E(2)), although glycyrrhizin did not show such an activity. Moreover, the estrogen receptor alpha-dependent neurite outgrowth induced by the extract was similar to that by ...
We performed a randomized trial to compare IVF outcomes in 54 poor responder patients undergoing a microdose leuprolide acetate (LA) protocol or a GnRH antagonist protocol incorporating a luteal phase E2 patch and GnRH antagonist in the preceding menstrual cycle. Cancellation rates, number of oocytes retrieved, clinical pregnancy rates (PR), and ongoing PRs were similar between the two groups.
Cord blood transplantation (CBT) with units containing total nucleated cell (TNC) dose e;2.5×107/kg is associated with improved engraftment and decreased transplant-related...Full Text Available
Nine coals from Spanish, British, German and American mining basins were hydrogenated using Fe catalyst precursors (red mud and FeSO{sub 4}), without solvent at 300, 350, and 400 {degree}C and 10 MPa of H{sub 2}. Overall conversion and product distribution are related to the textural characteristics of the original coals and are studies throughout the distinct hydrogenation processes. Results reveal that with FeSO{sub 4} as a catalyst precursor, conversions increase with coal surface area. However, when red mud (RM) is used, conversions are independent of coal textural characteristics. Higher conversions are obtained with FeSO{sub 4} than with RM at 300 and 350 {degree}C whereas at 400 {degree}C higher conversions are obtained with RM. This different catalytic activity is also reflected in the changes of the textural characteristics observed in each case. Up to 350 {degree}C, the ...
The thermal conductivity of steam has been measured as a function of temperature from 100 deg C to 515 deg C and pressure up to 500 bar using the coaxial cylinder method. Corrections to the apparent thermal conductivity data are detailed. Correlations of the thermal conductivity coefficients are given in terms of temperature and density.
The method and results are presented of measurements of the coefficients of "2"2"2Rn emanation from samples of fly- ashes and slag and other commonly used building materials. A chamber was used for electrostatic collection of "2"2"2Rn decay products. The coefficients of emanation ranged from 0.2% (fly- ashes) to 21.3% (phosphogipsum from phosphorit). (author).
In this work, the thermal performance of a conventional collector is improved by inserting porous substrates at the inner walls of the collector tubes. The porous substrates improve the convective heat transfer coefficient between the tube wall and the fluid. This improvement is investigated numerically and its effects on the efficiency and the useful gain of the collector are evaluated. It is found that inserting the porous substrate may raise the collector efficiency considerably, especially at high values of the overall heat loss coefficient.
This report contains a set of nomographs which can be used to estimate the average annual solar fraction for solar space and water heating at a large number of DOD facilities. The solar fraction estimated from the nomograph is in close agreement with F-Chart 3.0 and allows for variation of the following parameters: annual load, collector area, collector transmittance-absorptance coefficient, and collector overall loss coefficient.
A set of nomographs is presented which can be used to estimate the average annual solar fraction for solar space and water heating at a large number of DOD facilities. The solar fraction estimated from the nomograph is in close agreement with F-Chart 3.0 and allows for variation of the following parameters: annual load, collector area, collector transmittance-absorptance coefficient, and collector overall loss coefficient.
A set of nomographs is provided which can be used to estimate the average annual solar fraction for solar space and water heating at a large number of DOD facilities. The solar fraction estimated from the nomograph is in close agreement with F-Chart 3.0 and allows for variation of the following parameters: annual load, collector area, collector transmittance-absorption coefficient, and collector overall loss coefficient.
The change of the transport coefficient due to the fusion energy source is studied. The scale invariance property of the reduced set of equations is investigated in the presence of the self-heating term due to the fusion reaction. The pressure gradient as well as the fusion power are the free energy sources that dictate the turbulent transport. It is shown that the burning transport coefficient can have a form with much wider variety, and that the transport property could be different owing to the self-heating by the fusion reactions. (author)
Molar extinction coefficients for the solid solutes in aqueous solutions of some alkaline earth chlorides such as MgCl_2.6H_2O, CaCl_2, SrCl_2.6H_2O and BaCl_2.2H_2O have been determined at 81, 356, 511, 662, 1173 and 1332 keV energies in different concentration using the narrow beam transmission methods. (author)
General conclusions, principles and order of substantiating the extractable reserves and coefficients of oil extraction from oil and oil and gas fields are presented. Recommendations are made for solving questions of constructing calculation models for heterogeneous beds, schematization of the working conditions, selection of mathematical models for oil extraction for different geological-field conditions and different stages of ''life'' of the field.
Design constraints require that as Earth terminal attempting communications with a FLTSATCOM EHF Package (FEP) located onboard a FLTSATCOM satellite be provided with an accurate FEP package. To be precise, the terminal is provided with a coefficient element set from which the ephemeris of a satellite may be computed. This report describes the operation of a user friendly computer program that produces the above mentioned coefficient set so as to provide reference benchmarks from which the ephemeris related operations of the terminal can be judged.
Results of americium-242m and americium-242 preparation by irradiating initial americium-241 at a reactor in the form of a diphtalocyanine complex are presented. The enrichment coefficient, equalling 10, has been obtained using the extraction method of recoil atom separation from the parent isotope. Application of the chromatographic column with Dowex-50 permits to increase the enrichment coefficient of isotopes upto 24.6.
Annealing of magnetostrictive Metglas foils, subsequently incorporated into laminated Metglas/Pb(Zr, Ti)O3 magnetoelectric (ME) composites, is shown to result in improved magnetic properties, as well as ME coefficients. Annealing of the foils at 350 ?C resulted in partial crystallization, without oxidation or magnetic cluster formation that would reduce the magnetization. Laminate composites made with these annealed Metglas foils had improved ME coefficients.
This paper introduces the summary of design guideline (draft) for the limit state design method for foundation structures, and examples of calculations on pile foundations. The limit states were set using the load to transformation curves, and the limit state No. 3 in particular assumed a large earthquake, a state that a foundation is fatally damaged because of rarely acting loads that lead to generation of displacement and loss of stability and functions. Ground survey coefficient, ground resistance coefficient, and ground property coefficient were defined especially as the safety coefficients. With respect to the displacement in the limit state No. 3, a restriction value was set for the plasticity of the foundation. Loads were given considerations of combination of permanent load, variation load, and accidental load, each having been set with a load coefficient. It was decided ...
This paper addresses the unique structural requirements for successful conversion of tankers for floating production storage and offloading (FPSO) or floating storage and offloading (FSO) service. A description is given of the steps undertaken during two recent and very different conversions of a highly optimized 1980s VLCC to FPSO service, and a typical robust 1970s ULCC to FSO service. The paper describes the steps needed for ensuring the FPSO or FSO requirements are successfully met during conversion of the two tankers - each having its own history, e.g. date of build, original design, material choices, class society, voyage history and repairs. Firstly, the paper describes the procedure and results of an early initial structural assessment procedure on the basis of an American Bureau o...
Phosphate/chromate and accelerated chromate coatings were produced on commercially available aluminium. The Cr, P and Fe components of the conversion coatings were determined by radioactive tracer technique. The tracer technique was combined with ion-exchange and film-sectioning methods to determine the chromium(III)/total chromium ratio in the accelerated chromate coating. It was found that during the acidic dissolution of the conversion coating the chromium(III)/total chromium ratio may suffer changes. The film-forming components in the metal/bath interface are supersaturated and deposited onto the aluminium. The identified components of the accelerated chromate coatings are Cr(OH)sub(3), Cr(OH)CrOsub(4) and Crsub(4)(Fe(CN)sub(6))sub(3) and the chromium(III)/total chromium ratio was found to be cca. 2/3. (author). 11 refs.; 5 figs.
The Science Council accepted the recommendations of the Swan Wooster report on Opportunities for coal liquefaction research in British Columbia, Vancouver, BC, Canada, Science Council of British Columbia, 173 pp (May 1980), following review by the Sub-committee on Coal Research. The Sub-Committee has recommended a four year Research and Development programme on B.C. coals to be carried out at B.C. Research Council. About 5 million dollars would be spent during the four year period. The overall objective is to provide sufficient technical data to identify and evaluate coal conversion opportunities in B.C. A significant secondary objective is to provide a group of trained engineers and scientists in the Province familiar with the technology of coal conversion. (1 ref.)
Silica glasses containing Pr"3"+ with and without CdS nanoparticles were prepared by sol-gel technique. The influence of CdS nanoparticles on Pr"3"+ doped glass was studied by absorption, photoluminescence and up-conversion. From the measured intensities of various absorption bands of these glasses, the Judd-Ofelt parameters ?_2, ?_4 and ?_6 have been evaluated. The radiative transition probability (A), radiative lifetime (?_R), branching ratio (?_R) and integrated emission cross-section (?_P) were calculated from excited states of "3P_1 and "3P_0 levels. The up-conversion emissions were found in the green, orange and red regions under 800 nm excitation with peaks 559, 612 and 688 nm respectively. On excitation with 370 nm also leads to similar green, orange and red regions.
Conversion of the microprocessors and software for the Mold Heating and Cooling (MHAC) pump package control systems was initiated to allow required system enhancements and provide data communications capabilities with the Plastics Information and Control System (PICS). The existing microprocessor-based control systems for the pump packages use an Intel 8088-based microprocessor board with a maximum of 64 Kbytes of program memory. The requirements for the system conversion were developed, and hardware has been selected to allow maximum reuse of existing hardware and software while providing the required additional capabilities and capacity. The new hardware will incorporate an Intel 80286-based microprocessor board with an 80287 math coprocessor, the system includes additional memory, I/O, and RS232 communication ports.
In seeking ways to reduce emissions from two-stroke locomotive type engines, the Navy has evaluated dual-fuel conversions operating on a compression ignition cycle, using up to 94% natural gas and 6% diesel pilot fuel. The Navy has conducted an evaluation and test program under the direction of Dr. Normnn L. Helgeson, at the Naval Facilities Engineering Service Center in Port Hueneme, California. Of the Navy`s many diesel engines, those installed in its MUSE (mobile utility support equipment) units for temporary electrical power were the first Navy off-road engines to be affected by emissions regulations. Most of the units are powered by the EMD 645 engine, and when burning diesel fuel do not meet the emission requirements in many areas of the country. This paper discusses the changes and results of the conversion and shakedown tests.
Energy harvesting systems stimulate the development of power management for low power consumption applications. Improving the converter efficiency of power management circuits has become a significant issue in energy harvesting system design. This paper presents a variable step-down conversion ratio switched capacitor (SC) DC-DC converter to advance the converter efficiency of charge on the stored capacitor in a wireless monitoring system of orthopedic implants. The converter is designed to work at 1 MHz switching frequency and achieves 15 to 2 V conversion. Measurement results show that the converter efficiency can reach 42% including all circuit power consumption, which is much higher than previous work. (semiconductor integrated circuits)
In the present thesis, the shell structure in exotic nuclei has been investigated. The focus of the work was on finding new experimental data in neutron-rich Cr and proton-rich Ca isotopes. The investigation of light Ca isotopes concentrated on the nucleus {sup 36}Ca which was produced in a knockout reaction from a radioactive {sup 37}Ca beam. For {sup 36}Ca, the excitation energy of the first 2{sup +} state has been measured for the first time. Furthermore, momentum distributions were analyzed using a Monte-Carlo simulation of the knockout reaction. This analysis yielded the contributions of neutrons from individual orbitals to the total knockout cross section. In principle, these may be used to calculate spectroscopic factors, but such a calculation is hampered by difficulties of present knockout-reaction models in predicting precise single-particle cross sections. The measured branching ratio to the ground and excited states, on the other hand, is close to the predicted value. A ...
vehicles including the H2-A rocket and the space shuttle. .... The vacuum can's main function is to provide a high vacuum so that the science experiment and its sensors ... EMI-shielded power conversion from the incoming ISS power supply. 4. ...
Molecular Misreading (MM) is the inaccurate conversion of genomic information into aberrant proteins. For example, when RNA polymerase II transcribes a GAGAG motif it synthesizes at low frequency RNA...Full Text Available
The present invention relates to a method of recycling polymeric waste products into monomers and high value forms of carbon by pyrolytic conversion using an induction coupled RF plasma heated reactor.
The metabolism of DDT has been followed in pure lines of laboratory-reared resistant and susceptible anophelines using gas-liquid chromatography. Relatively large amounts of DDE were formed in...Full Text Available
The purpose of the conversion process is to convert the {sup 233}U fluoride compounds that are being extracted from the Molten Salt Reactor Experiment (MSRE) equipment to a stable oxide for long-term storage at Bldg. 3019.
SummarySoluble epoxide hydrolase (sEH) is a key enzyme in the metabolic conversion and degradation of P450 eicosanoids called epoxyeicosatrienoic acids (EETs). Genetic variations...Full Text Available
Technologies for materials, processes, and manufacturing that will provide safe, .... advanced energy conversion techniques, and pulsed inductive and ... duration antimatter storage and transportation, and methods for utilizing ...... EVA systems can be found in the EVA Technology Roadmap of the EVA Project Plan. ...
The speA gene in Bacillus subtilis encodes arginine decarboxylase, which catalyzes the conversion of arginine to agmatine. Arginine decarboxylase is an important enzyme...Full Text Available
The high-yield, stereoselective conversion of geraniol (3,7-dimethyl-trans-2,6-octadien-1-ol) to the insect juvenile hormone, methyl 12,14-dihomojuvenate (methyl cis-10-epoxy-3,11-dimethyl-7-ethyl-trans,...Full Text Available
Electron cyclotron emission (ECE) can be used to determine the electron temperature profile in magnetized plasmas. The complex structure of the magnetic field configuration in the Large Helical Device (LHD), which has a large shear, complicates the analysis of the ECE spectrum. In a sheared magnetic field the propagation of X and O-mode polarization through the plasma are coupled, causing mode conversion and polarization rotation. Mode scrambling is also caused by wall reflections. In this report, this mode conversion in LHD is numerically analyzed. It was found that at low density mode conversion scrambles the ECE spectra. However, at higher density (n{sub eo} > 1.0{center_dot}10{sup 19} m{sup -3}) the polarization mode is found to rotate with the sheared magnetic field, yielding only a negligible mode conversion. Wall reflections are found to depolarize the ECE spectrum. Notwithstanding the LHD ...
Phenylketonuria (PKU) is a common genetic disorder in humans that arises from deficient activity of phenylalanine hydroxylase (PAH), which catalyzes the conversion of phenylalanine to tyrosine....Full Text Available
Dimethacrylate polymers and composites are seeing increased usage in orthopedics. As these applications require the material to integrate with the surrounding tissues, direct contact cytotoxicity...Full Text Available
The conversion of coal to oil can be carried out in two ways. A synthesis route and a degradation route. Each of these routes are described and several degradation processes are explored. The testing of several fuels produced from coal is also given considerations.
Extra-terrestrial exploration and development missions of the next century will require reliable, low-mass power generation modules of 100 kW_e and more. These modules will be required to support both fixed-base and manned rover/explorer power needs. Low insolation levels at and beyond Mars and long periods of darkness on the moon make solar conversion less desirable for surface missions. For these missions, a closed Brayton cycle energy conversion system coupled with a reactor heat source is a very attractive approach. The authors conducted parametric studies to assess optimized system design trends for nuclear-Brayton systems as a function of operating environment and user requirements. The inherent design flexibility of the closed Brayton cycle energy conversion system permits ready adaptation of the system to future design constraints. This paper describes a dramatic contrast between system designs requiring man-rated ...
The concept of nanocrystal conversion chemistry, which involves the use of pre-formed nanoparticles as templates for chemical transformation into derivative solids, has emerged as a powerful approach for designing the synthesis of complex nanocrystalline solids. The general strategy exploits established synthetic capabilities in simple nanocrystal systems and uses these nanocrystals as templates that help to define the composition, crystal structure, and morphology of product nanocrystals. This article highlights key examples of 'conversion chemistry' approaches to the synthesis of nanocrystalline solids using a variety of techniques, including galvanic replacement, diffusion, oxidation, and ion exchange. The discussion is organized according to classes of solids, highlighting the diverse target systems that are accessible using similar chemical concepts: metals, oxides, chalcogenides, phosphides, alloys, intermetallic compounds, sulfides, and ...
A process is described for covering methane to a higher order hydrocarbon comprising contacting a gaseous reactant consisting of methane with a phosphate-containing catalyst for a sufficient period of time and at an effective temperature to provide the phosphate-containing catalyst consisting essentially of the higher order hydrocarbon. The catalyst is represented by a formula.
Because copper catalyzes the conversion of H2O2 to hydroxyl radicals in vitro, it has been proposed that oxidative DNA damage may be an important component of copper toxicity....Full Text Available
BackgroundThe immunoregulatory enzyme indoleamine 2,3-dioxygenase, which catalyzes the conversion of tryptophan into kynurenine, is expressed in a significant subset of patients...Full Text Available
The objective of the current research in coal liquefaction is to produce a synthetic crude from coal at a cost lower than $30.00 per barrel (Task A). A second objective is to produce a fuel which is low in aromatics, yet of sufficiently high octane number for use in the gasoline-burning transportation vehicles of today. To meet this second objective, research was proposed for conversion of the highly-aromatic liquid product from coal conversion to a product high in isoparaffins, which compounds in the gasoline range exhibit a high octane number (Task B). Experimental coal liquefaction studies conducted in a batch microreactor in the laboratory have demonstrated potential for high conversions of coal to liquids with low yields of hydrocarbon (HC) gases, hence small consumption of hydrogen in the primary liquefaction step. Ratios of liquids/HC gases as high as 30/1, at liquid yields as high as 82% of the coal by weight, have ...
The authors investigate the possibility of the direct heterogeneous catalytic synthesis of ethylbenzoate from benzonitrile. The catalysts tested were oxides of aluminium, titanium, and vanadium. The main conversion product detected chromatographically was ethylbenzoate; benzaldehyde, benzamide, and benzanilide were also identified. Aluminium oxide was found to be the most effective catalyst.
This is an internal DOE Geothermal Program document. This document contains summaries of projects related to exploration technology, reservoir technology, drilling technology, conversion technology, materials, biochemical processes, and direct heat applications. [DJE-2005
In order to develop a high-efficiency coal pyrolysis method, flash pyrolysis was experimented on slurry prepared by using liquid-phase oxidation reformed coal and a methanol-based solvent mixture. Australian Morwell coal was used for the experiment. The oxidized coal, into which carboxyl groups have been introduced, has the condensation structure relaxed largely, and becomes highly fluid slurry by means of the solvent. Char production can be suppressed by making the oxidation-pretreated coal into slurry, resulting in drastically improved pyrolytic conversion. The slurry was divided into dissolved solution, dried substance, extracted residue, and residual slurry, which were pyrolized independently. The dissolved solution showed very high conversion. Improvement in the conversion is contributed by separating the dissolved substances (coal macromolecules) at molecular levels, coagulating the molecules, suppressing cross-link ...
Finasteride, a specific and competitive inhibitor of 5α-reductase enzyme Type 2, inhibits the conversion of testosterone to dihydrotestosterone (DHT). In adults, DHT acts as primary androgen...Full Text Available
BackgroundCyclooxygenase (cox) is the rate-limiting enzyme, which catalyzes the conversion of arachidonic acid into prostaglandins and contributes to the inflammatory process. Cyclooxygenase-2...Full Text Available
The 7 conference papers in Vol. 9 review the implications of environmental problems and discuss the consequences of pollution abatement measures, especially for the economics of energy conversion. The future developments of pollutant emissions are assessed.
...wood smoke, emissions, pollution, heaters, environment, Earthbeat - 25/5/2002: Woodsmoke, Health & the Environment Love that Planet All in the Mind The Buzz Health Report In Conversation Ockhams Razor Science Show The Lab Health Matters Catalyst Quantum ...
The hypothesis that the antiarrhythmic drug amiodarone slows down the heart rate by its inhibitory action on the intracellular conversion of thyroxine (T4) to 3,5,3' triiodothyronine (T3) was investigated....Full Text Available
A new process for the hydrogenation of coal in the presence of wide-cut coal tar was proposed; it involves cavitation treatment, mixing with catalytic additives, and heating the resulting mixture at an elevated pressure in an atmosphere of hydrogen. The yields of hydrocarbon fractions to 300?C and gas condensate were evaluated.
The incorporation of [14C]phenylalanine and [1,6-14C]shikimic acid into tyrosine was investigated in the callus of Portulaca grandiflora, var. JR (L.). By inhibiting...Full Text Available
DOE is supporting the development of several conversion processes that are currently in the pilot plant stage. Each of these processes is described briefly and information given as to contractor, contract, funding, site and current progress. Several support projects are treated similarly. (LTN)
Several isolates of bacteria and fungi from soil, together with cells released directly from soil, were studied with respect to buoyant density and dry weight. The specific volume (cubic centimeters...Full Text Available
The objective of this project is to identify feasible Louisiana-grown biomass crops and residues, to combine these with technically and economically feasible conversion processes, and to provide integrated biomass energy production systems in Louisiana. Among the recommended integrated systems are: cotton gin trash and rice hull processing residues used for either direct combustion or methane or ethanol production. Steam generation via direct combustion is recommended. Hardwood chips are economically feasible despite considerable price and supply instability, while high sugar or starch content crops are easily converted to ethanol but limited by price. Possible breakthroughs in biomass production or in the hydrolysis of starch or cellulose substrates may decrease processing costs. Recommended areas for future study dealing with production include: (1) increase biomass availability and density; (2) increase harvesting, transportation and storage technologies; (3) ...
An assay to measure the rate of enzymatic formation of 3-methylindole (3MI) from indoleacetic acid (IAA) in Lactobacillus sp. strain 11201 was developed. The reaction mixture contained 50 micrograms...Full Text Available
The overall goal of the Gas-to-Liquids Program at the U.S. Department of Energy`s Pittsburgh Energy Technology Center (PETC) is to develop technologies for the production of hydrocarbon fuels and premium chemicals from light alkane gases. PETC`s current Gas-to-Liquids Program comprises the development of four primary advanced conversion technologies, namely, partial oxidation, oxidative coupling, oxyhydrochlorination, and novel conversion processes. Based on the current state of development, it can be concluded that, in the near future, one or more of these technologies will reach proof-of-concept demonstration. Oxyhydrochlorination is the most advanced direct conversion technology, and the synthesis of lower cost methyl chloride from natural gas would impact several commercial technologies that utilize methyl chloride as an intermediate to high value products. Technology development for the partial oxidation of methane to ...
Study of the conversion of chicken litter to biogas for the production of energy. There was an additional requirement that after extracting the energy from the chicken litter the nutrient value of the raw chicken litter had to be returned to the Ak-Chin Farms for use as fertilizer in a form and delivery method acceptable to the Farm.
This report describes studies made during the fourth quarter of 1986 using the revised microautoclave experimental technique. Studies were made of the effect of reaction time on conversion using Kemmerer coal. Results that, at least during the first 30 minutes, conversion is a monotonically increasing function of reaction time and temperature. A study was also made of the effect of temperature on conversion. In general, conversion increased with temperature. The reactivity of coal appears to be unaffected by exposure to Certigrav fluid, if the exposed coal is subjected to two acetone washings under a nitrogen blanket. Work was started on using SCR-II process solvent in place of tetralin. Results indicate that SRC-II process solvent is a satisfactory solvent donor for high reactivity, high ash bituminous coals, but slightly less effective for low ash, subbituminous coals. Some tests were made to examine ...
Recent research at the laboratory scale by a number of organizations in different countries has shown that with the use of particular types of solvents it is possible to achieve almost complete conversion of coal to liquid products under relatively mild process conditions. This work is reviewed and the conclusions to be drawn from it are summarized.
A shear acoustic transducer-lens system in which a shear polarized piezoelectric material excites shear polarized waves at one end of a buffer rod having a lens at the other end which excites longitudinal waves in a coupling medium by mode conversion at selected locations on the lens.
A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a {sup 137}Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 {+-} 0.9 cm{sup 2} y{sup -1}, is in good agreement with the values quoted by other ...
A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a "1"3"7Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data. The average biodiffusion coefficient, at 1.8 #+-# 0.9 cm"2 y"-"1, is in good agreement with the values quoted by other workers on ...
The primary E1, M1 and E2 ..gamma..-radiation in /sup 87,88,89/Sr observed after thermal neutron capture was compared with the predictions of single particle and giant resonance models. The nuclei feature a wide range of neutron binding energies between 6.3 and 11.1 MeV, which makes a 5.5 MeV spectrum of primary transition energies available for investigation. The (n, ..gamma..) reaction was used to estimate the parameters of the spin-flip M1 giant resonance in strontium. The total energy weighted M1 strength of this resonance exceeds the results of shell model and random phase approximation calculations for /sup 90/Zr by a factor of 3-4. The E1 strengths were found to agree with the established giant dipole resonance model. The few data on primary E2 transitions do not allow to differentiate between the giant quadrupole resonance and the single particle models.
The primary E1, M1 and E2 #gamma#-radiation in "8"7","8"8","8"9Sr observed after thermal neutron capture was compared with the predictions of single particle and giant resonance models. The nuclei feature a wide range of neutron binding energies between 6.3 and 11.1 MeV, which makes a 5.5 MeV spectrum of primary transition energies available for investigation. The (n, #gamma#) reaction was used to estimate the parameters of the spin-flip M1 giant resonance in strontium. The total energy weighted M1 strength of this resonance exceeds the results of shell model and random phase approximation calculations for "9"0Zr by a factor of 3-4. The E1 strengths were found to agree with the established giant dipole resonance model. The few data on primary E2 transitions do not allow to differentiate between the giant quadrupole resonance and the single particle models. (orig.).
Estrogen metabolism is suggested to play an important role in estrogen-induced breast carcinogenesis. Epidemiologic studies suggest that diets rich in phytoestrogens are associated with a reduced risk of breast cancer. Phytoestrogens are biologically active plant compounds that structurally mimic 17b-estradiol (E2). We hypothesize that phytoestrogens, may provide protection against breast carcinogenesis by altering the expression of estrogen-metabolizing enzymes cytochrome P450 1A1 (Cyp1A1) and 1B1 (Cyp1B1). Cyp1A1 and Cyp1B1 are responsible for the metabolism of E2 to generate 2-hydroxyestradiol (2-OHE2) and 4-hydroxyestradiol (4-OHE2), respectively. Studies suggest that 2-OHE2 and 2-methoxyestradiol may protect against breast carcinogenesis, while 4-OHE2 is carcinogenic in rodent models....
A nuclear battery based on the direct energy conversion of the fission products is presented. Such energy conversion is possible by using a nuclear reactor with ultra-thin fuel elements of 0.2 {mu}m of {sup 242m}Am. The amount of nuclear fuel is 376 g and the dimensions of the battery are 2.4x2.4x2.4 m{sup 3} (including the vacuum spacing), with a BeO moderator and Be electrodes. The total power of the reactor is 10.6 MW and the electrical power is 0.652 MW.
This paper reports on the results of experiments into efficient higher-order anti-Stokes Raman conversion of tunable short-pulse XeCl laser radiation. The maximum output energy of the pumping laser, in which the radiation of a frequency-doubled dye laser is amplified by two XeCl laser amplifiers, is 55 mJ with a pulse duration of 1 ns FWHM. Using hydrogen gas as a Raman medium, a series of anti-Stokes lines up to the 12th order (121.5 nm) is generated in the vacuum ultraviolet (VUV) region. 16 references.
According to W. H. Wiser and A. G. Oblad, the program at the University of Utah to develop coal conversion techniques, which has received federal grants of $1.35 million since 1969, recently was awarded $425,000 from the U.S. Office of Coal Research for the development of catalysts for coal conversion and low-sulfur fuel oil production. In tests, 100 lb of coal have been converted into 95 lb of products composed of 30 lb liquid fuel like gasoline, 5 lb of diesel or fuel oil, 30 lb of gaseous fuel, and 30 lb of char.
Polymer electrolyte membrane fuel cells (PEMFCs) are energy conversion devices that produce electricity from a supply of fuel, such as hydrogen. One of the major challenges in achieving efficient energy conversion is the development of cost-effective materials that can act as electrocatalysts for PEMFCs. In this letter, we demonstrate that, instead of conventional noble metals, such as platinum, chromium nitride nanocrystals of fcc structure exhibit attractive catalytic activity for PEMFCs. Device testing indicates good stability of nitride nanocrystals in low temperature fuel cell operational environment.
This paper reports the presence of face centered cubic cobalt precipitates inside tungsten carbide in nanocomposite of WC-Co synthesized by spray conversion processing. EDS was used to identify the presence and micro-diffraction was employed to determine the nature of the precipitates. There is entrapment of cobalt in tungsten carbide during the spray conversion process used to form WC/Co powder. During consolidation, at high temperatures, the cobalt attains enough mobility to precipitate inside WC. A vanadium containing compound was seen at the interfaces in samples which incorporated VC as a grain growth inhibitor. (orig.)
Four high-sulphur low-rank coals have been treated at hydrogenation conditions with three iron-based catalyst precursors: Red Mud (Fe[sub 2]O[sub 3]), iron sulphide and iron pentacarbonyl. The obtained yields show a dependence with the sulphur content of the coals; the organic sulphur content correlates with the conversion and THF-solubles when Red Mud and iron sulphide are added. In spite of the high hydrogen sulphide partial pressure in the reaction, the addition of other sources of sulphur enhances the percentages in conversion products. 15 refs., 2 figs., 3 tabs.
We report investigations of enhancement in material conversion efficiency of KDP for SHG applications. The limitation of conventional technique of growing KDP crystal was overcome in the present work by adopting a growth method to grow KDP directly in type-II phase matching direction. The conventional technique results in #approx#30% of the crystal volume usable for SHG applications whereas the present method has resulted in enhancing it to #approx#90%. The orientation of the element was confirmed by frequency conversion experiment using Nd:YAG laser. The UV-vis transmittance obtained was 92%. The interferometric results show that the crystals have excellent optical homogeneity.
Fluidized bed technology was experimentally evaluated for the combustion and gasification of cotton gin waste. The isothermal bed temperatures in the reactors could be maintained below the ash fusion point of the waste. Raw stripper harvested cotton gin trash could be metered directly into the fluidized-bed reactors indicating that little feed preparation is required. H and CO were the primary products of gasification, and approximately 3200-400 Btu of gas were produced per lb of cotton gin waste. These techniques offer the potential of providing small-scale energy conversion systems for use on farms.
Biomass can provide a substantial energy source. Liquids are preferred for use as transportation fuels because of their high energy density and handling ease and safety. Liquid fuel production from biomass can be accomplished by any of several different processes including hydrolysis and fermentation of the carbohydrates to alcohol fuels, thermal gasification and synthesis of alcohol or hydrocarbon fuels, direct extraction of biologically produced hydrocarbons such as seed oils or algae lipids, or direct thermochemical conversion of the biomass to liquids and catalytic upgrading to hydrocarbon fuels. This report discusses direct thermochemical conversion to achieve biomass liquefaction and the requirements for wastewater treatment inherent in such processing. 21 refs.
The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through February 1999.
The objective of this contract is to research, develop and demonstrate a novel ceramic membrane reactor system for the low-cost conversion of natural gas to synthesis gas and hydrogen for liquid transportation fuels: the ITM Syngas process. Through an eight-year, three-phase program, the technology will be developed and scaled up to obtain the technical, engineering, operating and economic data necessary for the final step to full commercialization of the Gas-to-Liquids (GTL) conversion technology. This report is a summary of activities through September 1999.
Knighton et al. used a pulsed high pressure mass spectrometer to examine thermal electron detachment from C_6F_6"-. This technique had been used earlier for the measurement or detachment rate coefficients for azulene anions as a function of temperature. C_6F_6"- and c-C_4F_6"- have been studied by Datskos et al. using a pulsed drift tube. In our laboratory, we have used a flowing afterglow Langmuir probe (FALP) apparatus to measure the thermal electron detachment rate coefficient for c-C_4F_8"- ions at 375 K. We have also measured the electron attachment rate coefficient for c-C_4F_8 at 303 K and 375 K. (author).
The half-value thicknesses, linear and mass attenuation coefficients of biological samples such as bone, muscle, fat and water have been measured at 140, 364 and 662keV ?-ray energies by using the ATOMLABTM-930 medical spectrometer. The ?-rays were obtained from 99mTc, 131I and 137Cs ?-ray point sources. Also theoretical calculations have been performed in order to obtain the half-value thicknesses and, mass and linear attenuation coefficients at photon energies 0.001keV-20MeV for bone, muscle and water samples. The calculated value and the experimental results of this work and the other results in literature are found to be in good agreement.
A noninvasive method is described for estimating local cerebral blood flow (LCBF) and local partition coefficients by means of computed tomographic scanning during inhalation of 30% stable xenon gas in oxygen. Time-dependent xenon concentrations in arterial blood and brain tissue during the wash-in and washout phases are used to calculate partition coefficients and LCBF values by means of a least-squares curve-fitting analysis. Control values for partition coefficient and LCBF obtained from control subjects with minor head trauma in the chronic stage were compatible with those in several past reports, and reproducibility was satisfactory. The theoretic grounds underlying this new method of curve-fitting analysis are discussed.
A noninvasive method is described for estimating local cerebral blood flow (LCBF) and local partition coefficients by means of computed tomographic scanning during inhalation of 30% stable xenon gas in oxygen. Time-dependent xenon concentrations in arterial blood and brain tissue during the wash-in and washout phases are used to calculate partition coefficients and LCBF values by means of a least-squares curve-fitting analysis. Control values for partition coefficient and LCBF obtained from control subjects with minor head trauma in the chronic stage were compatible with those in several past reports, and reproducibility was satisfactory. The theoretic grounds underlying this new method of curve-fitting analysis are discussed.
Internal friction of amorphous Pd/sub 80/Si/sub 20/ metal doped with hydrogen or deuterium was measured with a specially designed apparatus using amorphous metal sheet as a part of the electric oscillating circuit. Two peaks in Q/sup -1/ curve are observed. Applying the peak shift method to the first Snoek-like peak, we can determine the relaxation time from which the microdiffusion coefficient can be calculated. The obtained microdiffusion coefficient is about 10/sup -14/ m/sup 2//s at 200 K, being comparable with the macrodiffusion coefficient obtained from the releasing method. It can, however, not elucidate the hydrogen isotopic effect on the peak temperature of Q/sup -1/ curve, the activation energy for relaxation and the relaxation time from the present work because of the broadness of obtained Q/sup -1/ curve.
An experimental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 m/s. An illustrative example of the use of the theory for industrial ventilation is presented. (author)
X-ray diffraction offers a unique combination of advantages for kinetic study which include the non-destructive nature of the measurement, the use of bulk crystals, and the convenience of the experimental arrangements. These attributes and the availability of position-sensitive detectors and high-flux synchrotron radiation sources make this technique most useful for in situ, dynamical investigations. When using diffraction techniques to determine a diffusion coefficient, the principle of analysis entails a scattering theory and a kinetic model. The former allows the kinetic parameter(s) to be extracted from measured intensity, while the latter relates the kinetic parameter(s) to the diffusion coefficient(s). Three examples are demonstrated: (1) Palladium Silicide (Pd{sub 2}Si) Layer Growth on Silicon, (2) Decomposition of an Ni-12.5at%Si Superalloy, and (3) Short-range Ordering in Cu-Au Solid Solutions.
The energy levels, wavelengths, oscillator strengths, Auger rates and level-to-level dielectronic recombination rate coefficients describing dielectronic recombination into excited levels of Ne-like titanium from F-like low-lying states are calculated. Our calculations are based on Dr. R.D. Cowan's semi-relativistic mass-velocity and Darwin corrections are included in the Hamiltonian, and the distorted-wave model is used for the calculation of free electron wavefunctions. In order to set the recombination rate coefficients on a level by level basis, in a manner compatible with detailed level population kinetics modelling of highly-stripped ions in plasma, the dielectronic recombination rate coefficients as a function of free electron temperatures are given in an analytical form, which is not only very convenient in practice, but also hopefully accurate compared with the exactly calculated numerical results. (orig.).
Dimensioning of actinides waste packages for long duration storage has to take into account helium production from natural decay and release rates from the material. For the latter, we propose here an improved method for the determination of the helium diffusion coefficient in britholite, to be used for minor actinides storage. This work is based on results we previously published using the classical three steps method: "3He implantation on a Van de Graaff facility, "3He profile determination analysing the protons resulting from the "3He(d,p)"4He reaction in a nuclear microprobe, evolution of the helium profile during annealings. Taking explicitly into account the incident deuterons energy stragglings allows us to show that the implanted helium profiles are bimodal, each component leading to a different helium diffusion coefficient.
#epsilon#_m(Ce"4"+) values of the ceric-cereus system have been measured and the experimental procedure is described. Both routine titration method and electrochemical measurement were used. Some interference factors, such as ultraviolet, acidity and temperature, were studied as well. The temperature coefficient of #epsilon#_m(Ce"4"+) value in this experiment is about -0.1% degree C"-"1. A statistic analysis was made for 24 experimental values of #epsilon#_m(Ce"4"+) and a Gaussian distribution was found. Ultimately, an average molar extinction coefficient of 553.2 +- 1.3 m"2#centre dot#mol"-"1 was obtained at #approx#320 nm in 0.4 mol/L H_2SO_4 system, with a relative standard deviation of 0.24% (95% confidence level) and a total uncertainty of 1.5%.
Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m{sup 2}K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)
Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m"2K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)
(Boiling site densities and heat-transfer coefficients have been measured for ethanol-water and ethanol-benzene mixtures at 1.01 bar for a heated vertical brass disk. A strong effect of composition on the boiling site density was observed, which was attributed to the nature of the activation of the boiling surface and mass diffusion effects. The boiling heat-transfer coefficient was found to decrease with increasin subcooling, but for the mixtures at a given level of subcooling the decrease was less than that for the single components and azeotropic mixtures.) The heat-transfer coefficient at a given heat flux was seen to be quite insensitive to the very large increase in boiling site density in comparing the pure water and the ethanol-water azeotrope results, leading one to question pool boiling models that predict heat-transfer rates on the basis of boiling site density.
A method based on path integral formulation is given for obtaining exact solution of the s states for the Bargmann potentialV(r)=1ka"2#beta#(#beta#-1)e"-"2"r"/"a1-e"-"r"/"a"2-Ae"-"r"/"a1-e"-"r"/"a,where #beta# and k are parameters. The exact energy spectrum and the normalised s-state eigenfunctions are obtained from the poles of the Green function and their residues, respectively. The results are compared with their of Schrodinger formalism, special cases are also discussed.
The high-spin states in transitional odd-mass nuclei are studied in terms of an odd quasi-particle coupled to an asymmetric rotor with a variable moment of inertia (VMI). In order to take into account the VMI, the basis states are expanded in terms of the core eigenfunctions. Excitation energies, quadrupole moments, magnetic moments, B(E2) values and B(M1) values are calculated and compared with the experimental data for nuclei in Au and La regions. On comparison with other descriptions it is found that the treatment with VMI provides a more satisfactory explanation of the data. (Auth.).
This report is the 1992 annual progress report for the Energy Conversion and Storage Program, a part of the Energy and Environment Division of the Lawrence Berkeley Laboratory. Work described falls into three broad areas: electrochemistry; chemical applications; and materials applications. The Energy Conversion and Storage Program applies principles of chemistry and materials science to solve problems in several areas: (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes and chemical species, and (5) study and application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, ...
The precipitation reaction of some rare earth chlorides (La/Ce/Nd/GdCl3) in a LiCl-KCl molten salt has been carried out by using the oxygen sparging method. In this study, regardless of the oxygen sparging time and the molten salt temperature, oxychlorides (REOCl) for LaCl3, NdCl3 and GdCl3, and an oxide (REO2) for CeCl3 are formed as a precipitate. The conversion of rare-earth chlorides into insoluble precipitates was described by using a conversion ratio. The conversion ratio increased exponentially with the oxygen sparging time and finally showed asymptotic value at 1,023K of the molten salt temperature condition. The conversion ratios of LaCl3, NdCl3 and GdCl3 were increased with the molten salt temperature, however, even though the conversion ratio was increased from 0.660 to 0.995 with increasing molten salt temperature from 823 to 923 K at 60 min of a sparging time, the ...
A major regulatory element required for expression of the human [alpha]-globin genes is located 40 kb upstream of the embryonic [zeta]-globin gene. To understand how this and other locus control region (LCR) elements contribute to high-level expression in erythroid cells, we have performed high-resolution, in vivo dimethyl sulfate footprinting. In addition, we have modified the dimethyl sulfate-based ligation-mediated polymerase chain reaction in vivo footprinting procedure to permit the assessment of interactions at guanine and adenine residues, rather than guanines alone. In vivo footprinting of the human [alpha]-LCR element carried on chromosome 16 in a mouse erythroleukemia cell environment revealed protein occupancy at GATA-1, AP-1/NF-E2, and CACC/GGTGG motifs, specific differences compared with in vitro protein binding, and distinct changes in one region upon dimethyl sulfoxide-induced cellular maturation. No protein contacts were ...
Ovarian function was evaluated in 11 women 16 to 43 years of age at treatment who received doxorubicin, cyclophosphamide, and high doses of methotrexate with or without radiotherapy in adjuvant therapy of soft tissue sarcoma. Five women (16-33 yr old) who received chemotherapy alone or combined with radiotherapy only at sites distant from the ovaries (chest wall, thigh, and leg) had minimal menstrual irregularities or temporary cessation of menses during therapy; cyclic menses returned promptly after therapy. Gonadotropin levels (expressed as means +/- SD (follicle-stimulating hormone (FSH), 10 +/- 5 mlU/ml; luteinizing hormone (LH), 10 +/- 4 mlU/ml) and 17 beta-estradiol (E2) levels (means +/- SD, 208 +/- 147 pg/ml) were normal. By contrast, 4 older women (ages 36-43 yr) who received similar treatment developed persistent amenorrhea with postmenopausal levels of gonadotropin (FSH, 108 +/- 29 mlU/ml; LH, 72 +/- 19 mlU/ml) and ...
The angular ..gamma gamma..-correlations for nuclei of Sr even-even isotopes with A=82, 84, 86, 88 were measured. Multipole structurs of ..gamma..-transtion series and th coefficients multipole mixing were determined.
The angular #gamma##gamma#-correlations for nuclei of Sr even-even isotopes with a=8 82, 84, 86, 88 were measured. Multipole structurs of #gamma#-transtion series and th coefficients multipole mixing were determined.
1. Rates and rate coefficients of glucose utilization and replacement were determined with [5-3H]- and [U-14C]-glucose in rats starved for 24h, either conscious or under halothane anaesthesia, in a...Full Text Available
We calculate the Bogolubov coefficients for a metric which describes the snapping of a cosmic string. If we insist on a matching condition for all times {\\it and} a particle interpretation, we find no particle creation.
Molar extinction coefficients of some carbohydrates viz. L-arabinose (C5H10O5), D-glucose (C6H12O6), D-mannose (C6H12O6), D-galactose (C6H12O6), D(-) fructose (C6H12O6) and maltose (C12H24O12) in aqueous solutions have been determined at 81, 356, 511, 662, 1173 and 1332 keV by gamma ray transmission method in a narrow beam good geometry set-up. These coefficients have been found to depend upon the photon energy following a 4-parameter polynomial. These extinction coefficients for different sugars having the same molecular formula have same values varying within experimental uncertainty. Within concentration ranges studied, Beer--Lambert law is obeyed very well.
Mass attenuation coefficients of amino acids viz. glycerine (C_2H_5NO_2), 1-Serine (C_3H_7NO_3), 1-Theronine (C_4H_9NO_3), 1-Proline (C_5H_9NO_2), 1-Valine (C_5H_1_1NO_2) and 1-Phenylalanine (C_9H_1_1NO_2) in aqueous solutions have been determined at 81, 356, 511, 662, 1173 and 1332 keV by the gamma-ray transmission method in a narrow beam good geometry setup. Precisely measured densities of these solutions were used for the determination of these coefficients which varied systematically with the corresponding changes in the concentrations (g/cm"3) of the solutions. Molar extinction coefficients of amino acids were then obtained at these energies and were found to be in good agreement with the theoretical results. In addition, total interaction cross sections of amino acids in aqueous solutions were also calculated. (author)
The estimation of numerical values of the mean distance of closest approach of ions, a, of alkaline-earth metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.
Describes investigations into flow density, angle of repose, coefficients of friction and adhesion using poor quality anthracite culm (from the 50-letie Ukrainy mine) and anthracite slurry with a high ash content (from the Tsentral'naya and Partizanskaya mines) on samples of varying moisture content (2-22%). The results show that flow properties are impaired when anthracite has a moisture content of 8.5 to 9.5%; when these anthracites are used in electric power plants they should be stored in bunkers with walls with a slope of greater than 70 degrees (or dried) to prevent sticking. Results of investigations into internal and external friction, adhesion and cohesion varied for the different samples, but the highest coefficient of internal friction was found with concrete where it increases continuously with moisture content. With rubber, PVC, St. 3 steel and stainless steel, the friction coefficient increases with ...
The iron(III) molar extinction coefficient in H/sub 2/O-0.4 M H/sub 2/SO/ sub 4/ solution at maximum absorption and 25 deg C, epsilon /sub s/, was determined to be 2220 plus or minus 20 liters mole/sup -1/ cm/sup -1/. The ratio of the iron(III) molar extinction coefficient in D/sub 2/O-0.4 M H/sub 2/SO/ sub 4/ solution at maximum absorption and 25 deg C to epsilon /sub s/ was found to be 1.068 P 0.004. The acidity effect is presented graphically, since the effect is nonlinear. The temperature coefficients were determined to be +(0.63 plus or minus 0.02)% per de gree centigrade for light water solutions and +(0.36 plus or minus 0.02)% per degree centigrade for heavy water solutions. (auth)
... the hydroxyl group with the benzene ring. The molar extinction coefficients for the various species at their respective absorption ... Glya Recorded by 1H-NMR Spectroscopy TABLE 2 Molar Extinction Coeff...
An important application of metal hydrides is as a moderator material in nuclear reactors. The fundamental properties of hydrides are illustrated and an impression given of the current research into hydrogen in transition metals. Phase diagrams, magnetic properties, temperature dependence of the diffusion coefficient, energy level schemes and superconductivity are considered. (C.F.).
Gas-solid chromatography was used to determine the Henry`s law second gas-solid virial coefficients within the temperature range of 314--615 K for ethane, propane, butane, isobutane, pentane, hexane, heptane, chloromethane, dichloromethane, trichloromethane, tetrachloromethane, trichlorofluoromethane (Freon 11), chlorodifluoromethane (Freon 22), dichlorodifluoromethane (Freon 12), methyl ether, ethyl ether, and sulfur hexafluoride with Carbopack B, a microporous carbon adsorbent. The temperature dependence of the second gas-solid virial coefficients of these adsorbates was used in conjunction with analyses based on a graphical method, a single-surface numeric integration method, a single-surface analytic expression method, and a two-surface analytic expression method to determine the gas-solid interaction energies and other parameters. The interaction energies were correlated with a ratio of the critical temperature divided by the square root ...
1. Rates and rate coefficients of glucose utilization and replacement in post-absorptive rats, either conscious or under halothane anaesthesia, were determined in a thermoneutral environment by using...Full Text Available
Scraped-surface heat transfer augmentation is proposed as a possible technique for use in improved air-cooling designs. Although it has been in common use with liquids, the technique has apparently never been used with gases. An experimental investigation...
Measurements have been made of radon ("2"2"2Rn), release from diverse quaternary samples collected from different sediment deposits in the Errachidia and Beni-Mellal areas (Morocco). The radon diffusion coefficient as one of some important parameters of radon transport in the soil has been measured using solid state nuclear track detectors (SSNTD). Radon #alpha#-activity, uranium content and radon exhalation rate have been determined in the studied samples. Uranium concentrations were found to vary from 0.14 to 9.52 ppm whereas the radon exhalation rate varied from 0.003 to 0.145 Bq x m"-"2 x h"-"1. A positive correlation has been found between radon exhalation rate and uranium content in the studied samples. The average radon diffusion coefficients were found to vary from (1.26 #+-# 0.09) x 10"-"6 m"2 x s"-"1 to (4.3 #+-# 0.36) x 10"-"6 m"2 x s"-"1. Furthermore, the correlation between "2"2"2Rn diffusion coefficient and ...
Short-lived fission gas release from fuel pellets during irradiation was investigated based on the experimental results of the gas-flow rigs irradiated in the Halden Heavy Water Reactor (HBWR). The release-to-birth (R/B) rates of short-lived fission gas were measured by means of gas-flow measurement during the irradiation experiments. Surface-to-volume (S/V) ratios of fuel pellets and diffusion coefficients of short-lived fission gas release were evaluated from the obtained (R/B) values. The increase of (S/V) ratio agreed well with the point where the fuel temperature exceeded the threshold of 1% fission gas release. This indicates that the interlinkage of fission gas bubbles occurred there. The evaluated diffusion coefficients scattered in the range between 10"-"2"3 and 10"-"1"7 m"2/s, and the effects of fuel type (UO_2 or MOX) were not clearly observed. In addition, it is likely that the restructuring effect of fuel pellet on the diffusion ...
A heat transfer (condenser) of a domestic freezer was tested in a vertical channel in order to study the influence of the chimney effect in the optimization of the heat transfer coefficient. The variation of the opening of the channel, position and the heating power of the heat exchanger in the heat transfer coefficient was considered. The influence of the surface emissivity on the heat transfer by thermal radiation was studied with the heat exchanger testes without paint and with black paint. The air velocity entering the channel was measured with a hot wire anemometer. In order to evaluate the chimney effect, the heat exchanger was testes in a open ambient. This situation simulates its operational conditions when installed on the freezer system. The variables collected in the experimental procedures was gathered in the form of dimensionless parameters as Nusselt, Rayleigh, Grashof and Prandtl numbers, and dimensional parameters of the ...
The authors extend the Fermilab formalism for heavy quarks to develop an {Omicron}(a{sup 2}) improved relativistic action. They discuss their construction of the action, including the identification of redundant operators and the calculation of the improvement coefficients.
Problems of classification and regression estimation in which objects are represented by multidimensional arrays of features are considered. Many practical statements can be reduced to such problems, for example, the popular approach to the description of images as a set of patches and a set of descriptors in each patch or the description of an object in the form of a set of distances from it to certain support objects selected based on a set of features. For solving problems concerning the objects thus described, a generalization of the relevance vector model is proposed. In this generalization, specific regularization coefficients are defined for each dimension of the multidimensional array of the object description; the resultant regularization coefficient for a given element in the mul...
Passage of neon gas through activated charcoal is planned to be the primary method of removing impurities from the liquid neon scintillator in the CLEAN experiment. In order to quantify this technique, the breakout curves for hydrogen, nitrogen, argon and krypton impurities in neon-saturated activated charcoal were measured. Adsorption coefficients and the number of theoretical stages were measured for hydrogen in the temperature range between 300 and 80 K, nitrogen between 300 and 200 K, and argon between 300 and 190 K. The adsorption coefficient for krypton was measured at 300 K.
A thermodynamic analysis of a hybrid geothermal heat pump system is carried out. Mass, energy, and exergy balances are applied to the system, which has a cooling tower as a heat rejection unit, and system performance is evaluated in terms of coefficient of performance and exergy efficiency. The heating coefficient of performance for the overall system is found to be 5.34, while the corresponding exergy efficiency is 63.4%. The effect of ambient temperature on the exergy destruction and exergy efficiency is investigated for the system components. The results indicate that the performance of hybrid geothermal heat pump systems is superior to air-source heat pumps.
Densities were measured with a vibrating-tube densimeter for binary mixtures of dimethyl sulfoxide + thiophene at temperatures from 293.15 to 313.15 K as a function of composition. Molar excess volumes V[sup E] for the mixtures, determined from the density data, are negative and become more negative with an increase in temperature. The coefficients of thermal expansion were also evaluated from the temperature dependence of the density.
Reflection coefficients of electromagnetic waves in a nonuniform plasma layer with electrons, positive ions and negative ions, covering a metal surface are investigated by using the finite-difference-time-domain method. It is shown that the reflection coefficients are influenced greatly by the density gradient on the layer edge, layer thickness and electron proportion, i.e., the effect of the negative ions. It is also found that low reflection or high attenuation can be reached by properly choosing high electron proportion, thick plasma layer, and smooth density gradient in the low frequency regime, but sharp density gradient in the high frequency regime. (authors)
Reactive sticking coefficients (RSCs) were measured for silane and disilane on polycrystalline silicon for a wide range of temperature and flux (pressure) conditions. The data were obtained from deposition-rate measurements using molecular beam scattering and a very low-pressure cold-wall reactor. The RSCs have nonlinear Arrhenius temperature dependencies and decrease with increasing flux at low (710 /sup 0/C) temperatures. Several simple models are proposed to explain these observations. The results are compared with previous studies of the SiH/sub 4//Si(s) reaction and low-pressure chemical vapor deposition-rate measurements.
A practical method to determine the ionic diffusion coefficient and activation energy by using quasielastic light scattering (QELS) is presented. It is shown that a temperature dependence curve of the QELS intensity at a fixed frequency can be well fitted by Jonscher's formula and that the diffusion parameters can be obtained from this curve fitting. This method is successfully applied not only to crystals with high optical quality, as reported earlier, but also to opaque ceramics, which are more important than the crystals from a practical point of view. The composition dependence of the ionic diffusion coefficient is studied in sintered YbSZ to show the usefulness of this method.
Experimental data on the gas holdup and the mean bubble size in a bubble column with a single nozzle was obtained for gas-molten salt systems of a eutectic mixture of LiCl (58 mol %)-KCl (42 mol %) and molten NaNO/sub 3/. The liquid-phase mass transfer coefficient K /SUB L/ was evaluated from the specific surface area a and the volumetric coefficient K /SUB L/ a data for oxygen and carbon dioxide absorption into molten NaNO/sub 3/. The dimensionless correlations of the performance of bubble columns for aqueous solutions can be extended to the gas-molten salt systems.
Developed is a simple method alloing one to determine the k-loop coefficient of #beta# function in gauge theories provided the operator expansion is constructed in (k-1) loop for certain two-point functions. The calculation of the two-loop coefficient of the Gell-Mann-Low function becomes trival - it reduces to a few algebraic operations with expressions which are already known. As an example spinor, scalar and supersymmetric electrodynamics are considered. Although the corresponding results for #beta#"("2") are known in the literature, both the method of the calculations and some points referring to the construction of the operator expansion are novel.
The mine dumps that arise from the gold mining operations in South Africa are a potential source of high concentrations of radon (222"Rn). Studying the diffusion of radon and the emanation from the soil will help to deduce the radon flux from these dumps to identify the problem areas for rehabilitation. This study describes measurements of the emanation coefficient and the modelling of the depth profile of the radon activity concentration, which is compared to a depth profile that was measured on such a mine dump. Emanation coefficients ranging from 0.13 to 0.39 have been obtained.
The entrainment flow rate distribution, the gas velocity profile, and the concentration profile of droplets across the channel cross section in fully developed region of a horizontal rectangular channel of 150mm width and 50mm height were measured. The concentration profile of droplets was expressed by a simple equation based on a constant diffusion coefficient model. From this equation the effects of gravity and turbulent diffusion of droplets on the concentration profile were evaluated. The characteristic mean settling velocity of a group of droplets with various diameters was derived, and using this value the mean diffusion coefficient of the group of droplets was obtained
The entrainment flow rate distribution, the gas velocity profile, and the concentration profile of droplets across the channel cross section in fully developed region of a horizontal rectangular channel of 150 mm width and 50 mm height were measured. The concentration profile of droplets was expressed by a simple equation based on a constant diffusion coefficient model. From this equation the effects of gravity and turbulent diffusion of droplets on the concentration profile were evaluated. The characteristic mean settling velocity of a group of droplets with various diameters was derived, and using this value the mean diffusion coefficient of the group of droplets was obtained. (author).
Microporous membranes are suitable for the CO{sub 2}-MEA (monoethanolamine) system because the overall mass transfer coefficient K of the membrane is approximately 10 times larger than that of composite membranes consisting of microporous membranes and homogeneous membranes. The overall volumetric mass transfer coefficient K{center_dot} of the hollow-fiber contact is more than 5 times larger than that of a conventional packed bed, which suggests that adorption using the present method has the advantage of making the absorption more compact. 8 refs., 7 figs., 4 tabs.
Experiments were conducted to study the condensation heat transfer characteristics of horizontal enhanced tubes. In the current experiment, six different enhanced tubes, including 26, 40 fpi low fin tubes and four three-dimensional-fin tubes, were tested. The working fluid used in the experiment was HCFC-22. Data were presented in the form of overall heat transfer coefficient at three working pressures, namely 1.32, 1.47 and 1.62 Mpa. In addition, the condensing heat transfer coefficients for the test tubes were obtained from the Wilson plot technique.
Retention kinetics and tissue partition coefficients for "8"5Kr were determined in rats exposed to known concentrations of "8"5Kr gas. The tissue partition coefficients were used to calculate the relative tissue radiation dose, assuming exposure conditions equivalent to the maximum permissible concentration in air (MPC)a. The estimated radiation dose was highest in adrenals and body fat, about twice the dose estimated for the next highest tissue, ovaries. Saturation and desaturation curves show that the contents of the large intestines have a prolonged desaturation time compared to other samples analyzed.
Performance assessments for the Area 5 Radioactive Waste Management Site on the Nevada Test Site have used three different mathematical models to estimate Rn-222 flux density. This study describes the performance, uncertainty, and sensitivity of the three models which include the U.S. Nuclear Regulatory Commission Regulatory Guide 3.64 analytical method and two numerical methods. The uncertainty of each model was determined by Monte Carlo simulation using Latin hypercube sampling. The global sensitivity was investigated using Morris one-at-time screening method, sample-based correlation and regression methods, the variance-based extended Fourier amplitude sensitivity test, and Sobol's sensitivity indices. The models were found to produce similar estimates of the mean and median flux density, but to have different uncertainties and sensitivities. When the Rn-222 effective diffusion coefficient was estimated using five different published predictive models, ...
Spectral absorption properties of total suspended matter (TSM) and colored dissolved organic matter (CDOM) are important for the use of the bio-optical model to estimate water quality parameters. This study aims to investigate the variation in the absorption coefficients of TSM and CDOM of inland waters. A total of 92 water samples were collected from Shitoukoumen Reservoir and Songhua Lake in Northeast China, analyzed for TSM and Chl-a, and measured for the absorption coefficient of TSM, CDOM and total pigments using a laboratory spectrophotometer. The absorption coefficient of TSM has been decomposed for phytoplankton and inorganic sediments. The results show that for Shitoukoumen Reservoir, CDOM has strong absorptions with shallow absorption slopes (i.e., the coefficient S in a(?)=a(?0)exp[-S(?- ?0)]) and large absorption at 355 nm; and for Songhua Lake, CDOM follows similar spectral absorption ...
The diffusion coefficient of radioactive radon (Rn) through buffer materials from low-level radwaste disposal site was determined in this present study by measuring the time-dependent diffusion of radon through a thin slab of the material. The diffusion process was required to reach a steady state so as to obtain a good estimate of the diffusion coefficient. A numerical method using the nonlinear least-squares and Marquardt`s method (NLSM method) was proposed for characterizing the diffusion coefficient of Rn so as to determine whether the process has reached steady-state or not. Natural mordenite, a potential buffer material of LLW disposal facility, was selected as testing porous material. The NLSM method was shown by the results to be able to estimate the diffusion coefficient even if the process was in transient period. Additionally, this method was also demonstrated to agree well with the results ...
The purpose of the invention is a process for the production of a particularly finely divided, homogeneous transition metal phosphide and transition metal chalcogenide of Daltonian stochiometry by the conversion of at least one powder transition metal or a transition metal alloy with phosphorus or with a chalcogen at raised temperature, which is characterized by the fact that the conversion is carried out in the presence of at least one inert finely divided auxiliary material which is soluble in water and does not sinter together at the reaction temperature, and that the conversion produce removes the auxiliary material. Even relatively small quantities of the auxiliary material are sufficient to ensure rapid and homogeneous conversion of the reaction partners to the reaction product having a large surface. A ratio of 1 part by volume of a mixture of a transition metal and phosphorus or chalcogen to 1 ...
The Energy Conversion and Storage Program applies chemistry and materials science principles to solve problems in (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes, and (5) application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials, and advanced methods of analysis. Electrochemistry research aims to develop advanced power systems for electric vehicle and stationary energy storage applications. Topics include identification of new electrochemical couples for advanced rechargeable batteries, improvements in battery and fuel-cell materials, and the establishment of engineering ...
The Energy Conversion and Storage Program applies chemistry and materials science principles to solve problems in (1) production of new synthetic fuels, (2) development of high-performance rechargeable batteries and fuel cells, (3) development of advanced thermochemical processes for energy conversion, (4) characterization of complex chemical processes, and (5) application of novel materials for energy conversion and transmission. Projects focus on transport-process principles, chemical kinetics, thermodynamics, separation processes, organic and physical chemistry, novel materials, and advanced methods of analysis. Electrochemistry research aims to develop advanced power systems for electric vehicle and stationary energy storage applications. Topics include identification of new electrochemical couples for advanced rechargeable batteries, improvements in battery and fuel-cell materials, and the establishment of engineering ...
This report describes progress on the Advanced Coal Liquefaction project by the Gulf Research and Development Company's Merriam Laboratory during the months of January through March 1983. The liquefaction behavior of Illinois No. 6 coal beneficiated in various ways was studied in both single-stage recycle (SRC II) and short contact time (SCT) modes of operation. The distillate yield increased as the iron level in the feed slurry increased in both modes of operation. In the SCT mode, the conversion increased at greater depths of cleaning. In the SRC II mode, the distillate yield and conversion were much higher with deep cleaning and add-back of pyrite than with conventional cleaning. Pyrite addition resulted in a significant increase in short contact time conversion of subbituminous Belle Ayr coal in both high and low quality solvents. Solvent quality itself, however, had little effect on ...
The control problem associated to a class of horizontal-axis fixed-pitch variable-speed low-power wind energy conversion systems, working in the partial load region, consisting in the energy conversion maximization, is approached here under the assumption that the wind turbine model and its parameters are poorly known. Using a new approach derived from the optimum seeking methods category, generically called Maximum Power Point Tracking (MPPT), the proposed control solution aims at driving the average position of the operating point near to optimality. Instead of inducing sinusoidal search signals, the wind turbulence is here used as search disturbance. The high-speed shaft's average rotational speed is slowly adjusted using the Fast Fourier Transform processing of some available measures from the system as an estimate of the operating point's position/distance to optimality. Numerical simulations are used for preliminary ...
Two-dimensional calculations are performed to obtain the conversion efficiency of traveling wave direct energy convertor adopted in a conceptual design of field reversed configuration D-"3He fusion reactor ARTEMIS. For fusion-born 14.67MeV protons, the efficiency obtained is very small compared with that from one-dimensional analysis. This is because the effective electric field for deceleration of the proton is smaller due to distortion of potentials near girds used to excite the traveling wave and because some fractions of the incident proton beams are inevitably lost to the grids with high energy. To increase the efficiency, the potentials may have to be increased. It seems from the two-dimensional analysis performed here that the conversion efficiency obtainable is less than about 60% with the maximum potential of about 6MV, while the corresponding values from the one-dimensional analysis are about 80% and 1.5MV, respectively. (author).
In this report, the concept of exergy and the general methodology of the exergetic analysis and the thermoeconomic (combined exergetic and economic) analysis of energy conversion systems are presented. The THESIS (THermodynamic and Economc SImulation System) computer program used for these analyses is briefly described. Detailed mass, energy, exergy and money balances for a reference steam power plant (Harry Allen Station) are shown. The effect of the most important process parameters on the overall efficiency is investigated. A year-by-year and a levelized revenue requirement analysis are presented. The costs of exergy losses are compared with the capital costs and other expenses due to owning and operating each particular plant component. The question whether it is profitable to reduce the exergy losses by increasing these costs and vice versa is investigated. A cost sensitivity analysis including the effect of coal price and average annual capacity factor is ...
The selective catalytic reduction of nitric oxide by methane over copper ion-exchanged natural zeolites was investigated in a packed-bed tubular reactor. The catalytic activity of Cu-N and Cu-H-N catalysts was confirmed as NO, CH{sub 4}, and O{sub 2} displayed very little reaction in the absence of any catalyst and zeolite without ion exchange was totally inactive. A maximum NO conversion of 33% at 650 C for Cu-N-66 was achieved with 2% NO and 1% CH{sub 4} and a contact time of 0.9 g s/cm{sup 3}, but the introduction of 2% O{sub 2} reduced the NO conversion to only 12%. Ion exchange for the H-form prior to copper ion exchange was essential for oxygen to promote catalytic activity over the temperature range 250--650 C, with a maximum conversion of 30% at 450 C with O{sub 2} present. The direct reduction of NO by methane was ruled out as a possible reaction pathway.
A highly efficient integrated energy conversion system is built based on a methane catalytic decomposition reactor (MCDR) together with a direct carbon fuel cell (DCFC) and an internal reforming solid oxide fuel cell (IRSOFC). In the MCDR, methane is decomposed to pure carbon and hydrogen. Carbon is used as the fuel of DCFC to generate power and produce pure carbon dioxide. The hydrogen and unconverted methane are used as the fuel in the IRSOFC. A gas turbine cycle is also used to produce more power output from the thermal energy generated in the IRSOFC. The output performance and efficiency of both the DCFC and IRSOFC are investigated and compared by development of exact models of them. It is found that this system has a unique loading flexibility due to the good high-loading property of DCFC and the good low loading property of IRSOFC. The effects of temperature, pressure, current densities, and methane conversion on the performance of the ...
The purpose of this study is to analyze the safeties and the economics for Co-60 production from Wolsung PHWR and to verify the feasibility on the manufacturing of the final Co-60 source for industrial irradiation. The feasibility of reactor conversion was carried out with KEPCO collaboration. Through the site survey on the experience of Gentililly-2 in Canada, a feasibility of plant conversion, changes in design, equipment and tools for Co-60 production was verified. It was estimated that the reactor conversion would not impose adverse impact on plant safety. For the encapsulation of radiation source and storage of the final products, a modification of concrete hot cell at KAERI was primary concerns. The installation and improvement of facilities are needed to avoid cross contamination and extra radiation exposure. Main items for these are pressure gauge, separated HEPA filter the ceiling separation, extra-shielding and ...
It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the hydrogen exchange reaction proceeds even in the reaction where radical does not give any effect. In the case of H2O addition, the conversion yield ...
For high-efficiency coal gasification, investigations were given on effect of coal chars with different conversion rates on coal gasification reactivity. In coal gasification, reactivity of char after pyrolysis governs the efficiency. The reference char conversion in CO2 gasification of coal (weight loss) changes linearly in the initial stage of the reaction, but the reactivity declines as the end point is approached. Char surface area is as large as 400 m{sup 2}/g in the initial stage with the conversion at 20%, but it decreases in the final stage. This phenomenon relates closely with changes in pore size and crystalline structure. Change in the Raman value R which shows incompleteness of char graphite structure and amorphous carbon ratio suggests that an active portion with high reactivity is oxidized preferentially, and a portion with low reactivity remains finally. Minerals in coal are known to accelerate the ...
With the end of the cold war the United States, Russia, and other countries have excess plutonium and other materials from the reductions in inventories of nuclear weapons. The United States Academy of Sciences (NAS) has recommended that these surplus fissile materials (SFMs) be processed so they are no more accessible than plutonium in spent nuclear fuel (SNF). This spent fuel standard, if adopted worldwide, would prevent rapid recovery of SFMs for the manufacture of nuclear weapons. The NAS recommended investigation of three sets of options for disposition of SFMs while meeting the spent fuel standard: (1) incorporate SFMs with highly radioactive materials and dispose of as waste, (2) partly burn the SFMs in reactors with conversion of the SFMs to SNF for disposal, and (3) dispose of the SFMs in deep boreholes. The US Government is investigating these options for SFM disposition. A new method for the disposition of SFMs is described herein: the simultaneous ...
Single crystals of semi-organic L-histidine hydrobromide have been grown by slow evaporation technique from a mixture of L-histidine and hydrobromic acid in aqueous solution at ambient temperature. From high-resolution X-ray diffraction analysis, the crystalline perfection of the grown crystal has been studied. Single crystal X-ray diffraction analyses, Nuclear Magnetic Resonance spectral analysis, Thermo-Gravimetry (TG), Differential Thermal Analysis (DTA) and hardness test have been employed to characterize the as-grown crystals. The UV cutoff wavelength of the grown crystal is below 300 nm and has a wide transparency window, which is suitable for second harmonic generation of laser in the blue region. Nonlinear optical characteristics have been studied using Q switched Nd:YAG laser (#lambda#=1064 nm). The second harmonic generation conversion efficiency of the grown crystals confirms their suitability for frequency conversion applications.
The consequences of converting a facility from brown coal fuel to gas fuel were analyzed by model simulation. Treated were a district heating plant with an output of 700 TJ/yr and minor local heating sources (stoves) at a density of 1 family house per 100 m"2. Emissions of particulate matter, sulfur dioxide, nitrogen oxides, carbon monoxide, and hydrocarbons before and after the conversion are given for the two types of source. Conversion of a major air pollution source to gas fuel would result in a reduction of the contribution of sulfur dioxide emissions of the order of 10"-"4, of particulate matter and carbon monoxide of the order of 10"-"3, and of hydrocarbons of the order of 10"-"2. The decrease will be lowest for nitrogen oxides, viz. about 40%. Analogous data for local heating sources in towns would be 10"-"5 for sulfur dioxide, 10"-"4 for particulate matter, 10"-"3 for carbon monoxide and hydrocarbons, and roughly one order of magnitude ...
Characteristic study for the recycled fuel cycle, MOX fuel and Th-MOX fuel in PWR was performed with the comparison of 4 w/o UO2 fuel. It was assumed that there are no limit in reprocessing and no technical difficulty in recycling of spent fuel. The effect of recycling, plutonium composition, conversion ratio, MTC, FTC was investigated to each cycle. (Th+Pu)O_2 recycle option was advantageous because the loading amount of plutonium could be reduced from 8.3 w/o at once-through cycle to 3.5 w/o. (Th+Pu)O_2 recycled fuel was known to be higher Pu-239 consumption rate and more Pu-240(242) production rate. The (Th+U)O2 and (U+Pu)O2 once-through fuel cycle revealed high conversion ratio. The (U+Pu)O_2 recycled fuel cycle, however, showed low conversion ratio. Safety of each cycle was ensured by negative MTC and FTC
This report details the status of the Biological Conversion of Synthesis Gas Project. The following tasks are described as being completed: (1) the test plan, (2) culture development, and (3) the mass transfer/kinetic studies. The bioreactor studies (Task 4) are underway. The continuous stirred tank reactor system for the conversion of H{sub 2}S to elemental sulfur using Chlorobium thiosulfatophilum has been studied for varying light intensities. The system was also modified to include both sulfur recovery and cell recycle using ceramic membranes. Studies were also performed to observe the effects of cell recycle using a polysulfone hollow filter membrane module. Work on Task 5, limiting conditions/scale-up, includes a scale-up study with three different size reactors to establish the optimum operating conditions for hydrogen production from synthesis gas by the biological water-gas shift reaction using the photosynthetic bacterium ...
The Korea Atomic Energy Research Institute has launched a decommissioning program of uranium conversion plant. One of the important tasks in the decommissioning program is the treatment of the sludge, which was generated during operation and stored in the two ponds of the lagoon. The treatment requires the volume reduction of lagoon sludges for the low cost of the program and the conversion of the chemical forms, including uranium, for the acceptance at the final disposal site. The physical properties, such as densities, were measured and chemical compositions and radiological properties were analyzed. The denitration was a candidate process which would satisfy the requirements for sludge treatment, and the characteristics of thermal decomposition and dissolution with water were analyzed. The main compounds of the sludge were ammonium and sodium nitrate from conversion plant and calcium nitrate, calcium carbonate from Ca ...
Testing of barrier properties of insulating materials against radon is usually based on the measurement of the radon diffusion coefficient. Presented report summarizes results of radon diffusion coefficients measurements in more than 120 insulating materials obtained throughout Europe. All measurements were performed by the Czech Technical University, Faculty of Civil Engineering in cooperation with the Radiation Protection Institute. We have found out that great differences exist in diffusion properties, because the diffusion coefficients vary within eight orders from 10"-"1"5 m"2/s to 10"-"8 m"2/s. For each material category of different chemical composition statistical evaluation of results is presented. Possibilities of usage of the radon diffusion coefficient for the design of radon resisting membranes are discussed. Based on the experience from the Czech Republic the paper is trying to show that ...
This study evaluated woody biomass from logging residues, small-diameter trees, mill residues, and urban waste as a feedstock for cellulosic ethanol conversion in Mississippi. The focus on Mississippi was to assess in-state regional variations and provide specific information of biomass estimates for those facilities interested in locating in Mississippi. Supply and cost of four woody biomass sources were derived from Forest Inventory Analysis (FIA) information, a recent forest inventory conducted by the Mississippi Institute for Forest Inventory, and primary production costs. According to our analysis, about 4.0 million dry tons of woody biomass are available for production of up to 1.2 billion liters of ethanol each year in Mississippi. The feedstock consists of 69% logging residues, 21%...
Although destruction of United States wetlands has slowed, their continued conversion, especially in certain inland regions of the country, may pose adverse ecological effects over the next few decades. The Army Corps of Engineers' regulatory program (Section 404 of the Clean Water Act) protects most coastal wetlands, but provides no protection for 95% of the country's wetlands which remain inland. These inland, freshwater wetlands, converted for agricultural purposes, comprise 80% of the wetland losses over the past 30 years. This report outlines options for more effective federal management, such as the mapping and categorizing of wetlands to determine relative values. In effect, agencies can focus protection programs on higher-value wetlands, especially those threatened by agricultural conversion. The report also discusses the contradictory federal policies aimed at wetlands; for example, the tax code encourages the ...
The intensity of erbium up-conversion luminescence could be limited by a saturation effect due to increased pump power. We studied the luminescence saturation of the 550 nm emission on erbium-doped, SiO_2-TiO_2 sol-gel powders under pulsed excitation at 979 and 1532 nm. From the latter, the up-converted luminescence intensity decreased with increasing excitation power, whereas no saturation was observed at 979 nm excitation. We proposed that the saturation effect is determined by the pump power, the erbium content and the lifetime of the corresponding first excited states at different pumping schemes.
An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements.
An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements
The process of radiation induced electron capture by protons or deuterons producing new ultra low momentum neutrons and neutrinos may be theoretically described within the standard field theoretical model of electroweak interactions. For protons or deuterons in the neighborhoods of surfaces of condensed matter metallic hydride cathodes, such conversions are determined in part by the collective plasma modes of the participating charged particles, e.g. electrons and protons. The radiation energy required for such low energy nuclear reactions may be supplied by the applied voltage required to push a strong charged current across a metallic hydride surface employed as a cathode within a chemical cell. The electroweak rates of the resulting ultra low momentum neutron production are computed from these considerations.
The authors report on temperature dependent characteristics and single mode performance of one-wave cavity, planar implanted, AlGaInP-based vertical-cavity surface emitting lasers. By optimizing the overlap between the gain peak and the cavity mode of the structure, they demonstrate record device performance, including 8.2 mW maximum output power and 11% power conversion efficiency for multimode operation and 1.9 mW and 9.6% power conversion efficiency for single mode operation at 687 nm. Improved performance at elevated temperatures is also achieved, with 1.5 mW output power demonstrated at 50 C from a 15-{micro}m-diameter device.
A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.
Ford, Bacon, Davis Utah Inc. has reevaluated the Spook site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings 48 mi northeast of Casper, in Converse County, Wyoming. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 187,000 tons of tailings at the Spook site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors.
An experimental investigation on the thermal decomposition of CH4 into C and H2 was carried out using a 5kW particle-flow solar chemical reactor tested in a solar furnace in the 1300-1600K range. The reactor features a continuous flow of CH4 laden with mm-sized carbon black particles, confined to a cavity receiver and directly exposed to concentrated solar irradiation of up to 1720 suns. The reactor performance was examined for varying operational parameters, namely the solar power input, seed particle volume fraction, gas volume flow rate, and CH4 molar concentration. Methane conversion and hydrogen yield exceeding 95% were obtained at residence times of less than 2.0s. A solar-to-chemical energy conversion efficiency of 16% was experimentally reached, and a maximum value of 31% was numer...
A solar energy collection and conversion system is disclosed in which a cassegrain mirror system is rotated about a diurnal axis, which axis is adjusted for seasonal variations in the incidence of the sun's rays on the earth's surface. A black body absorption cavity filled with translucent or transparent fluid material is used for direct absorption of the sun's rays. The incident solar energy is absorbed directly by the fluid medium. The fluid within the cavity may be maintained under extremely high pressures and temperatures in order to utilize this fluid as a heat storage medium. Such heat storage is facilitated by apparatus which permits a change in the volume of the reflective cavity in response to the temperature or pressure of the fluid within the cavity.
Efforts concentrated on updating of the Rockwell reference concept, definition of new system options, studies of special emphasis topics, further definition of the transportation system, and further program definition. The Rockwell reference satellite concept has a gallium arsenide (GaAs) solar cell array having flat concentrators with an effective concentration ratio of 1.83at end of life. Alternatives to this concept includes solid state power amplifiers or magnetrons for dc/RF conversion and multibandgap solar cells for solar to dc energy conversion. Two solid state concepts were studied. It was determined that the magnetron approach was the lowest mass and cost system.
Abstract in english Ru(1%)/SiO2 and Cu(1%)Ru(1%)/SiO2 catalysts were prepared by cogelation. The effect of pH and the amount of water on the physical-chemical properties and the catalytic properties of them were analyzed. The acid medium increased the formation of microporosity and the formation of small size of metallic ruthenium particle. The variation of the water quantity used in the gelation not modify considerably the texture neither the dispersion of the noble metal. The reduction lev (more) el of all prepared catalyst was similar, showing displacement in some of reduction peaks. The toluene hydrogenation indicated that the conversion and the quantity of hydrogenate product varied with the pH and the quantity of water used in the gelation. The addition of copper to Ru/SiO2 catalysts diminished the reactive conversion and their hydrogenant activity
Hydrogenation of high-volatile bituminous coal under high temperatures and pressures produced low-sulfur fuel oils. At a coal conversion of 80 percent, the ratio of oil to gas yields was approximately 3 : 1 and 23 percent of the coal sulfur was contained in the oil. Sulfur content of the oil, however, remained the same at different coal-conversion levels. The data obtained in the semicontinuous dilute-phase hydrogenation system showed that the whole oil can be directly used as a fuel oil where 1 percent sulfur is tolerated. Fuel oils containing 0.5 percent and 0.25 percent sulfur were produced by desulfurization of the whole oil.
Two natural gas/diesel dual fuel conversion systems for the Detroit Diesel 6V-71 transit bus engine were described. The basic concept of a dual fuel engine was to operate a diesel engine with both liquid fuel injection and a lean premixed gas mixture. The engine achieved high efficiency due to the high compression ratio typical of the diesel engine. Test results were obtained using three different calibrations on one engine. The objectives were to match existing engine performance with improved emissions and better overall fuel economics. Results showed that overall, engine conversion has both economic and emissions advantages over a straight diesel engine. However, the durability and in-use applicability of the system remains to be demonstrated with an in-bus demonstration project.. 3 tabs., 4 figs.
Point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54"0K. Both of these results are approximately 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency #OMEGA# = h#omega#/2eI/sub c/R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance, R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
Coordination chemistry on transition metal chalcogenides offer better conditions for multielectron charge transfer processes on solid/electrolyte interfaces. In this contribution, materials whose band energies are derived from d-states of the transition metal will be shown. Problems related to the reactivity, stability and photoactivity toward the generation and conversion of fuels will also be discussed. (orig.) [Deutsch] Die an halbleitenden Uebergangsmetall-Elektroden beobachtete Koordinationschemie bietet guenstige Voraussetzungen fuer den Mehrelektronen-Transfer an der Festkoerper/Elektrolyt Grenzflaeche. Beispielhaft werden in diesem Beitrag Elektrodenmaterialien vorgestellt, deren Energiebaender sich von d-Zustaenden der Uebergangsmetalle herleiten. Diskutiert werden Probleme der Reaktivitaet, der Stabilitaet und der Photoaktivitaet im Hinblick auf die Erzeugung und Umsetzung von Brennstoffen. (orig.)
This report describes progress during the first year of a three-year project. The objective of the research is to examine new design approaches for achieving very high conversion efficiencies. The program is divided into two areas. The first centers on exploring new thin-film approaches specifically designed for III-V semiconductors. The second area centers on exploring design approaches for achieving high conversion efficiencies without requiring extremely high quality material. Research activities consisted of an experimental study of minority carrier recombination in n-type, metal-organic chemical vapor deposition (MOCVD)-deposited GaAs, an assessment of the minority carrier lifetimes in n-GaAs grown by molecular beam epitaxy, and developing a high-efficiency cell fabrication process.
This report describes progress during the first year of a three-year project. The objective of the research is to examine new design approaches for achieving very high conversion efficiencies. The program is divided into two areas. The first centers on exploring new thin-film approaches specifically designed for III-V semiconductors. The second area centers on exploring design approaches for achieving high conversion efficiencies without requiring extremely high quality material. Research activities consisted of an experimental study of minority carrier recombination in n-type, metal-organic chemical vapor deposition (MOCVD)-deposited GaAs, an assessment of the minority carrier lifetimes in n-GaAs grown by molecular beam epitaxy, and developing a high-efficiency cell fabrication process.
Energy International is developing a technology that will create a staged formulation with the first coal form (Mulled Coal) that can be stored, transported, and pumped. Just prior to combustion, the Mulled Coal (MC) would be modified to provide the properties needed for proper atomization. This concept is an alternative to the expensive and energy intensive thermal drying processing of fine coal wet cakes. The material is suitable for both direct feed use in conventional and fluid bed combustors as well as on-site conversion to combustible slurries. By maintaining the coal form relatively close to the feed wet cake, only minor processing with low additive levels and low energy blending needed at the point of production. Its conversion to slurry or other use-feed form is made near the time of use and thus the requirements for stability, climatic control, and other storage, transport, and handling requirements are much less severe.
A new chemical reactor, the Open Plate Reactor, is being developed by Alfa Laval AB. It combines good mixing with high heat transfer capacity into one operation. With the new concept, highly exothermic reactions can be produced using more concentrated reactants. A nonlinear model of the reactor is derived and a control system is developed. For temperature control a cooling system is designed and experimentally verified, which uses a mid-ranging control structure to increase the operating range of the hydraulic equipment. A Model Predictive Controller is proposed to maximize the conversion under hard input and state constraints. An extended Kalman filter is designed to estimate unmeasured concentrations and parameters. Simulations show that the designed control system gives high conversion ...
Efficient, low-temperature conversion of infrared light into visible light (red, orange, green) is reported at single heterojunctions and undoped quantum wells of GaAs and ordered Al_xGa_1_-_xInP_2; an increase in photon energy of 700 meV is obtained. The signal originates from the high-band-gap layers and disappears only if the excitation energy is tuned below the GaAs band gap. The intensity of the up-converted photoluminescence (PL) is found to decrease significantly slower with increasing temperature than that of the regular PL and it remains observable up to 200 K. Interface-induced cold Auger processes along with the presence of trapped states for both electrons and holes in these ordered alloys account for this nonlinear mechanism. A colinear double-beam experiment confirms this. copyright 1996 The American Physical Society.
Hydrogenation of napthalene to tetralin using activated red mud as catalyst was studied as a typical hydrogen-donor system. Under the chosen reaction conditions, unprocessed red mud resulted in a conversion of napthalene of 3.55%. The most active catalyst, prepared by adding 20 wt% of TiO/SUB/2 to the red mud, followed by acid digestion and re-precipitation, resulted in a 58% conversion of naphthalene. This technology may have an important bearing on processes such as coal hydrogenation or crude-oil-residue processing, where the rate of reaction and product quality may depend upon the rate at which a hydrogen-donor solvent can be re-hydrogenated. (7 refs.)
An experiment lasting a number of hours was carried out with 6 men under standardised climate chamber conditions to find out to what extent wallpaper that reflects about 65-75% in the infra-red range by comparison with normal wallpaper that reflect only 3-5% of heat, has measurable positive effects on the thermoregulation of the human body and the human sensation of temperature. The measurements of skin temperature and heat flow intensity in the deeper areas of the body and the periphery, and metabolic heat conversion measurements (indirect calorimetry) confirm that infra-red reflection of the heat irradiated from the body lead to a measurable heat recovery on the body surface with a reduction of metabolic conversion. It was proved that it is possible to reduce the average room temperature by up to 4 K whilst maintaining the same degree of thermal comfort, which corresponds to a 20% saving in heating energy. (orig./BWI).
A highly efficient integrated energy conversion system is built based on a methane catalytic decomposition reactor (MCDR) together with a direct carbon fuel cell (DCFC) and an internal reforming solid oxide fuel cell (IRSOFC). In the MCDR, methane is decomposed to pure carbon and hydrogen. Carbon is used as the fuel of DCFC to generate power and produce pure carbon dioxide. The hydrogen and unconverted methane are used as the fuel in the IRSOFC. A gas turbine cycle is also used to produce more power output from the thermal energy generated in the IRSOFC. The output performance and efficiency of both the DCFC and IRSOFC are investigated and compared by development of exact models of them. It is found that this system has a unique loading flexibility due to the good high-loading property of ...
Co catalysts, obtained from a layered double Co?Zn?Al hydroxide, are highly active and stable towards the hydrogenolysis of glycerol to 1,2-propanediol (1,2-PDO) in aqueous media. The Co-673 catalyst, containing a CoO species, provided a glycerol conversion of 67.7% and a 1,2-PDO selectivity of 50.5%. The Co-873 catalyst comprising 16?nm Co nanoparticles gave a glycerol conversion of 70.6% and a 1,2-PDO selectivity of 57.8%. It was revealed that the CoO species in the Co-673 catalyst was readily converted to 50?nm Co particles under the glycerol hydrogenolysis conditions. The Co catalysts maintained a stable size and phase in recycling tests. Graphical Abstract
The RECH-1 MTR reactor has been converted from HEU to MEU (45% enrichment) and the decision to a LEU (20% enrichment) conversion was taken some years ago. This LEU conversion decision involved a local fuel development and fabrication based on U{sub 3}Si{sub 2}-Al dispersion fuel, and a fabrication qualification stage that resulted in four fuel elements fully complying with established fabrication standards for this type of fuel. This report-presents relevant points of these four leaders fuel elements fabrication, in particular a fuel plate core homogeneity control development. A summary of the intended in core follow-up studies for the leaders fuel elements is also presented here. (author)
Conversion of tropical forests to oil palm plantations in Malaysia and Indonesia has resulted in large-scale environmental degradation, loss of biodiversity and significant carbon emissions. For both countries to participate in the United Nation's REDD (Reduced Emission from Deforestation and Degradation) mechanism, assessment of forest carbon stocks, including the estimated loss in carbon from conversion to plantation, is needed. In this study, we use a combination of field and remote sensing data to quantify both the magnitude and the geographical distribution of carbon stock in forests and timber plantations, in Sabah, Malaysia, which has been the site of significant expansion of oil palm cultivation over the last two decades. Forest structure data from 129ha of research and inventory p...
During this reporting period two direct coal liquefaction experiments have been completed and a third is underway. These experiments have produced conversion and selectivity data on samples of Alabama bituminous coal slurried in tetralin and catalyzed using iron-titanium hydride. The experiments address the liquefaction of an agglomerating coal. Conversions of 45 to 55% DAF in 30 min have been recorded at 500/sup 0/F and 520 psia. Equipment modifications were made in an attempt to eliminate the problem of alloy binding in the hydride formation vessel. 4 figs., 4 tabs.
The main sources of energy that might be available in remote low populated areas of Libya are either diesel generating units or wind mills for water pumping. Several problems in the working performance of these two types of energy production may arise due to environmental conditions. Direct conversion of solar energy can replace other ways of energy delivery or production, especially in this country where the solar radiation all year is relatively high. Direct conversion of solar energy is relatively expensive, however the cost of erecting long feeders and supervising them may be much more expensive than the usage of solar systems. This paper investigates the economics associated with either solutions of energy production. A case study is given in detail to supply one of the remote areas with a population of about 250. (author)
During 1978 the Engineering Board of SRC granted Specially Promoted Program status to the Coal Technology program. This recognized that coal would increase in importance as the cost of liquid and gaseous hydrocarbons rises with the decreasing availability of petroleum related sources. It was, therefore, considered necessary to anticipate and improve, through SRC supported research, the technologies required to win, transport, convert to liquid and gaseous fuels and utilize coal and coal based substances. In view of the interest in the program, and also in the hope of reaching a still wider audience the reports of the two meetings have been combined in this single booklet. The reports indicate specific problems of importance in coal winning and coal conversion but, naturally, do not cover all of the program priorities.
Catalytic activity of industrial metallic wastes in coal liquefaction was examined in a 100lb/day continuous coal processing development unit. Red mud, a waste material from the aluminium industry, and an electric furnace flue dust containing Ni, Mo, Co and Fe showed a pronounced effect on the conversion of a Kentucky bituminous coal. Coal conversion and oil production increased significantly with the addition of red mud and flue dust. Comparison of the catalytic activity of pyrite, red mud, and flue dust, based on selectivity analysis, showed that red mud was the most desirable disposable catalyst. However, if the primary goal of coal liquefaction is high oil production, irrespective of hydrogen consumption, pyrite is the most active catalyst among those discussed in the paper.
Industrial solid wastes (fly ash and red mud, a by-product of the aluminium industry) have been employed as supports for preparation of Ru-based catalysts. Physical and chemical treatments on red mud were conducted and these modified supports were also used for preparation of Ru-based catalysts. Those Ru catalysts were characterized by various techniques such as N2 adsorption, H{sub 2} adsorption, XRD, XPS, and temperature-programmed reduction (TPR), and were then tested for catalytic ammonia decomposition to hydrogen. It was found that red-mud-supported Ru catalyst exhibits higher ammonia conversion and hydrogen production than fly-ash-supported catalyst. Heat and chemical treatments of the red mud greatly improve the catalytic activity. Moreover, a combination of acid and heat treatments produces the highest catalytic conversion of ammonia. 35 refs., 4 figs., 4 tabs.
A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).
A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).
The authors report here, for the first time, high frequency testing of a new type of electrochemical double layer capacitor (EDLC), based on carbon aerogels: the Aerocapacitor. Carbon aerogels, are a novel type of carbon foam developed by Lawrence Livermore National Laboratory for military applications. The unique properties of carbon aerogels, high surface area (700 m{sup 2}/g), high density (1g/cc), well controlled pore diameter and high material conductivity (25 S/cm) made it an ideal EDLC electrode material. Using carbon aerogel as the electrode material, the authors have developed Aerocapacitors. These new EDLC`s have a frequency response comparable to that of aluminum electrolytic capacitors and are thus ideally suited to power conversion applications.
This work reports an alternative methodology for the linear attenuation coefficient determination ({mu} {rho}) of irregular form samples, in such a way that is not necessary to consider the sample thickness. With this methodology, indigenous archaeological ceramics fragments from the region of Londrina, north of Parana, were studied. These ceramics fragments belong to the Kaingaing and Tupiguarani traditions. The equation for the {mu} {rho} determination employing the two mean method was obtained and it was used for {mu} {rho} determination by the gamma ray beam attenuation if immersed ceramics, by turns, in two different means with known linear attenuation coefficient. By the other side, {mu} theoretical value was determined with the XCOM computer code. This code uses as input the ceramics chemistry composition and provides an energy versus mass attenuation coefficient table. In order to validate the two mean method ...
The aim of this study is to clarify the radon behavior in the soil at the waste rock yards of uranium mine. We have developed an apparatus for measuring radon diffusion coefficient in soil under the control of soil temperature. The radon diffusion coefficients changed suddenly around the soil temperature of 0degC. The radon diffusion coefficients in dry soil have little temperature dependency, and were comparable coefficients obtained by empirical formula of Rogers and Nielson. To study the restraint effect of radon exhalation by covering with bentonite on soil, we carried out the measurements and the calculations by using one-dimensional transport model of atmosphere and soil. The decrease of radon exhalation rate was 2.9 Bq m"-"2s"-"1 when soil covered with the bentonite of 5 cm thick. The radon concentrations in snow cover and the radon flux from the snow surface were measured at the waste rock yard ...
Cylindrical test pieces of concrete are used for measurements of "2"2"2Rn exhalation rates. Except one flat end surface of a test piece, other parts of its exteriority are covered with sealant. Radon atoms can escape only through its end surface from the interior into the outside air. This treatment makes the radon transport in the concrete one dimensional phenomena. The piece is put in an airtight container. Time variations of radon concentrations in the air of the container are measured with a plane multiwire-electrode ionization chamber. From this result, the radon areal exhalation rate is deduced for the piece. Exhalation rates are measured for four pieces with different length. Then, the diffusion coefficient is obtained for radon in the concrete as (5.0 #+-# 1.0) x 10"-"8m"2s"-"1 (a one-block method). A two-block method has been invented to obtain simultaneously values of three parameters: diffusion coefficient, porosity of concrete, and ...
Some of the results of property measurements of CeO{sub 2} and its solid solutions were reviewed. The deviation from stoichiometry of undoped and doped CeO{sub 2} was presented in several figures, which suggested that CeO{sub 2} fired at high temperatures in air might be nonstoichiometric in some degree. At low temperatures, the deviation from stoichiometry in doped CeO{sub 2} is higher than undoped CeO{sub 2}. As another interesting property, CeO{sub 2} shows high solubility to trivalent cations such as rare earth elements. A possible reason behind this high solubility was presented. The nonstoichiometric defect in undoped CeO{sub 2} and the trivalent cation in solid solution with CeO{sub 2} have to be compensated by other defects. The possible defect structures in this solid solution were reviewed and the most probable structure was chosen based on density measurement and impurity dependence of oxygen diffusion coefficient. Finally the oxygen diffusion ...
A laser resonance absorption spectrometer is used to investigate the characteristics of both self and nitrogen collision broadened carbon dioxide in resonance with He--Ne laser radiation at 4.2 ..mu..m. The absorption coefficient in these broadening conditions has contributions from the R(28) to R(34) absorption lines of the ..nu../sub 3/ CO/sub 2/ spectrum. The Fletcher-Powell optimization method is used to reduce the raw absorption data and to find the best value average collision broadening coefficient and laser emission frequency for a Lorentzian line shape model of the contributing lines. Pure carbon dioxide absorption in a pressure range of from 0.0016 atm (1.25 Torr) to 0.33 atm (250 Torr) is described well by the model with an average self broadening coefficient of 0.084 +- 0.008 cm/sup -1/ atm/sup -1/ for laser frequencies located at either 2370.591 +- 0.020 cm/sup -1/ or 2371.135 +- 0.019 cm/sup -1/. Nitrogen ...
The Baikal Neutrino Telescope has been operating in its NT200 configuration since April, 1998. The telescope has been upgraded in April, 2005, to the 10 Mton scale detector NT200+. It's main physics goal is the detection of signals from high energy neutrino cascades. NT200+ reaches a 3-year sensitivity of 2 \\times 10^{-7}cm^{-2}s^{-1}sr^{-1}GeV for an all-flavor diffuse cosmic E^{-2} neutrino flux for energies 10^2 TeV \\div 10^5 TeV. Desgin and sensitivity of NT200+ are described. NT200+ is forming the basic building block of a future km3-scale (Gigaton-Volume) Baikal Telescope. Research and development work on that next stage detector has started.
High-spin states in {sup 177}Ta were produced using the {sup 170}Er({sup 11}B, 4{ital n}) reaction at 55 and 60 MeV. Considerable extensions have been made to the previously known level scheme, and new structures have been found. {ital B}({ital M}1)/{ital B}({ital E}2) ratios have been extracted for strongly coupled bands. The behavior of the different rotational cascades, in particular the anomalous crossing frequency observed in the [541]1/2{sup {minus}} proton {ital h}{sub 9/2} band and the occurrence of ``identical bands,`` is discussed. Comparisons are made with projected shell model calculations.
High-spin states in "1"7"7Ta were produced using the "1"7"0Er("1"1B, 4n) reaction at 55 and 60 MeV. Considerable extensions have been made to the previously known level scheme, and new structures have been found. B(M1)/B(E2) ratios have been extracted for strongly coupled bands. The behavior of the different rotational cascades, in particular the anomalous crossing frequency observed in the [541]1/2"- proton h_9_/_2 band and the occurrence of ''identical bands,'' is discussed. Comparisons are made with projected shell model calculations.
In the field of Living Probabilistic Safety Assessment (LPSA) the reliability data updating is an important factor. In risk analysis equipment failure data is needed to estimate the frequencies of events contributing to risk posed by a facility. Five years data of emergency diesel generator (EDG) of Daya Bay Nuclear Power Plant (NPP) has been studied in this paper. The data updating process has been done by using two methods, i.e., the classical method and Bayesian method. The aim of using these methods is to calculate the operational failure rate (@l) and demand failure probability (p). The results show that the operational failure rate is 1.7E-3 per hour and the demand failure probability is 2.4E-2 demand per day for Daya Bay NPP. By comparing the results obtain from classical and Bayesi...
For neutron radiography (NR), photographic techniques have been mainly used for many years. To observe a dynamic event and to test many samples, the real-time neutron radiography (i.e. neutron television - NTV) system has been introduced at the E-2 experimental tube of the Kyoto University Research Reactor (KUR). The NTV system has been practically applied to penetrating the side plates containing boron burnable poison to test MTR type reactor fuel, to investigation of moving objects and to neutron computed tomography (NCT). New approaches using some advanced neutron converters, a high sensitive and resolution TV camera and a high performance image processing system are being undertaken for standard indicators, visualization on air-water two-phase flow, NCT and so on. (author).
Proton and alpha decay from the giant resonance region of {sup 28}Si excited with a 129 MeV alpha particle beam has been measured in coincidence with inelastic alpha particles detected at 0{degree}. The angular correlation data show the presence of decay from both {ital E}0 and {ital E}2 giant resonances. The {ital E}0 giant resonance decays primarily through the {alpha}{sub 0}, {alpha}{sub 1}, {ital p}{sub 0}, and {ital p}{sub 1,2} channels with the branching ratios 18{plus minus}6 %, 24{plus minus}8 %, 23{plus minus}9 %, and 18{plus minus}8 %, respectively. Substantial direct decay is observed.
Given a double complex $X$ there are spectral sequences with the $E_2$ terms being either H$_I$ (H$_{II}(X))$ or H$_{II}($H$_I (X))$. But if $H_I(X)=H_{II}(X)=0$ both spectral sequences have all their terms 0. This can happen even though there is nonzero (co)homology of interest associated with $X$. This is frequently the case when dealing with Tate (co)homology. So in this situation the spectral sequences may not give any information about the (co)homology of interest. In this article we give a different way of constructing homology groups of $X$ when H$_I(X)=$H$_{II}(X)=0$. With this result we give a new and elementary proof of balance of Tate homology and cohomology.
Glycyrrhiza glabra root is one of the common traditional Chinese medicines and used as flavoring and sweetening agents for tobaccos, chewing gums, candies, toothpaste and beverages. While glycyrrhizin is one of the main components in the extract of G. glabra root and has been characterized, the other components have not been well characterized. The mechanism of growth activation of breast cancer MCF-7 cells, including the activation of Erk1/2 and Akt, and the transcriptional regulation of estrogen-responsive genes, was examined by means of sulforhodamine B, luciferase reporter gene, real-time RT-PCR and Western blotting assays after the induction of the cells with the extract of G. glabra root. The extract has similar activity to that induced by 17b-estradiol (E2), although glycyrrhizin di...
The mathematical calculation to obtain a radon diffusion coefficient from measured radon transient-diffusion data is usually done by fitting a difference equation to the data. The difference equation is obtained through transformation of the time-dependent diffusion equation based on Fick's law. But, actual measured transient-diffusion data often have much scatter. Therefore just fitting over the whole range of the measured data through the method of least squares may not always be valid, because the method offers mathematical interpretation rather than a physical one. Instead, the actual radon diffusion coefficients must be otherwise obtainable from measured radon transient data. Taking this viewpoint, the present paper claims that about a 90% leveling-off time is often easily discernible regardless of the shape of the radon transient curve obtained from the measured data and it can be a decisive factor for determining the radon diffusion ...
Six illitized samples from drillhole OL-KR12 in Olkiluoto were analyzed by helium gas methods for their diffusion coefficient, permeability and porosity. The diffusion coefficients measured varied in the range 2.1 x 10-10 - 3.5 x 10-8 m2/s, permeabilities in the range 6 x 10-21 - 5.8 x 10-16 m2, and porosities in the range 0.2 6.2%. Variations observed in these quantities were concluded to arise from the heterogeneous structure of the sample rock. A 4 mm x 4 mm x 4 mm subsample was sawed from each of the six samples for structural analysis by x-ray microtomography. The three-dimensional structure of tomographic reconstructions, and thereby that of the samples themselves, was analyzed visually, which confirmed their heterogeneity. Samples represent altered rock whose structure and thereby transport properties vary significantly depending on the local alteration history of the rock. (orig.)
The sensitivity analysis summarized in this paper was made to determine the parameters of greatest influence in the prediction of radon barrier cover thickness for the stabilization of uranium mill tailings piles. Such information provides the basis for setting priorities and levels of effort for data collection, and improves knowledge of the sources of uncertainty in the calculation of cover thickness. In the context of this paper, the influence of a parameter on cover thickness incorporates two effects: (1) the sensitivity of the mathematical formulation to changes in a parameter's value, and (2) the range of values that a parameter may take on under site-specific conditions. Of the several parameters that are used in the calculations, the most influential are cover moisture content, cover radon diffusion coefficient, tailings radium concentration and tailings radon emanating fraction, in order of decreasing relative influence. Less influential parameters for ...
One of the main goals in the determination of three-dimensional macromolecular structures from electron microscope images of individual molecules and complexes (single particles) is a sufficiently high spatial resolution, about 4 A, at which the interpretation with an atomic model becomes possible. To reach high resolution, an iterative refinement procedure using an expectation maximization algorithm is often used that leads to a more accurate alignment of the positional and orientational parameters for each particle. We show here the results of refinement algorithms that use a phase residual, a linear correlation coefficient, or a weighted correlation coefficient to align individual particles. The algorithms were applied to computer-generated data sets that contained projections from model structures, as well as noise. The algorithms show different degrees of over-fitting, especially at high resolution where the signal is weak. We demonstrate ...
The adverse effect of moisture diffusion on the properties of wood has been one of the main weaknesses of wood. Using a gamma irradiation method, wood-polymer composites have been produced which exhibit significant improvement in mechanical properties like compression, creep deformation and creep rupture particularly at high humidity. It has been thought that the impregnation of polymer into the wood has affected the moisture diffusion in the wood, so that its adverse effects on the mechanical properties has been reduced. In this report the apparent diffusion coefficients of a Ramin wood impregnated with varying amounts of polymethyl methacrylate (PMMA) were determined using a Fick's law approach. An initial linear relationship was found for impregnation of up to 70% PMMA, after which the diffusion coefficient levels off to a maximum value, for the three environmental relative humidity levels of 40, 60 and 90({plus minus}5)%. The ...
The adverse effect of moisture diffusion on the properties of wood has been one of the main weaknesses of wood. Using a gamma irradiation method, wood-polymer composites have been produced which exhibit significant improvement in mechanical properties like compression, creep deformation and creep rupture particularly at high humidity. It has been thought that the impregnation of polymer into the wood has affected the moisture diffusion in the wood, so that its adverse effects on the mechanical properties has been reduced. In this report the apparent diffusion coefficients of a Ramin wood impregnated with varying amounts of polymethyl methacrylate (PMMA) were determined using a Fick's law approach. An initial linear relationship was found for impregnation of up to 70% PMMA, after which the diffusion coefficient levels off to a maximum value, for the three environmental relative humidity levels of 40, 60 and 90(#+-#5)%. The phenomenon could be ...
Minority-carrier lifetime damage coefficients for 1 MeV electron, 3 MeV proton, and 6 MeV alpha particle irradiation of n-type (4.5{times}10{sup 15} and 1.3{times}10{sup 17}cm{sup {minus}3}) and p-type (2.5{times}10{sup 17}cm{sup {minus}3}) InP have been measured using time-resolved photoluminescence. These values are relatively insensitive to carrier type and show a slight increase with increasing carrier concentration. Evidence of comparable electron and hole capture lifetimes is found for the dominant recombination defect. The effect of 3 MeV proton and 6 MeV alpha particles relative to 1 MeV electrons is an increase in the lifetime damage coefficient by factors of about 10{sup 4} and 10{sup 5}, respectively. {copyright} {ital 1997 American Institute of Physics.}
Engineering materials for use in low heat rejection engines are required to function under stringent tribological conditions. Severe wear damage and high friction between the components of the tribosystem limit the number of potential materials suitable for such application conditions. The superalloys X-750 and 188 are composed of alloying elements that not only promote a high mechanical and chemical stability but may also result in a reduced wear rate and friction coefficient at elevated temperatures. As a part of the DOE-ECUT Tribology program at Argonne, the present study was undertaken to evaluate the tribological characteristics of these alloys that will also be utilized as the substrates for ion beam deposited lubricous coatings. A wear test rig that crudely simulated the sliding conditions between a piston ring and a cylinder liner in an operating engine was utilized for friction and wear studies. The test results indicated that the wear and friction ...
High-performance heat transfer augmentation methods applicable in the forced convection field of heat exchangers include a method which requires no external drive means, such as the insertion of a turbulence augmentation object into the flow passage and the use of a wave-shaped flow passage, but disturbs the main stream of flow to raise the heat transportation effect thereby to augment heat transfer in the flow passage. The heat transfer characteristics and thermal performance ratio achieved when sinusoidal-shape plates are inserted instead of augmentation objects, such as cylinders, with a high shape-induced resistance were studied. As a result, the relationship between the resistance coefficient, average Nusselt number, heat transfer coefficient, and pitch was clarified. It has been revealed that the use of eddies with a large gap flow and recirculation area should be considered in order to get a higher heat transfer ...
The calculation of nominal choke valve size determines the effective capacity for an oil and gas production system. The degree of restriction for the controlling area in the valve is a function of the surrounding geometry. In an orifice plate this is known as the 'velocity of approach' and can be used to determine the meter coefficient (C_m). This paper presents a technique for choke valves, based on the meter velocity of approach parameter, which can be used to predict the Valve Coefficient (C_v) for new trim designs. The prediction method uses a data trend based on a number of flow tests conducted on various trim characteristics. The resultant parametric equation is used to predict the C_v of a new trim geometry. The method relies on experimental data determined per IEC 60534-2-3, with calculations per IEC 60534-2-1. This paper further investigates the effect of varying upstream geometry on C_v for a 4'' nominal valve.
The diffusion of linalool and methylchavicol from thin (45-50 mm) antimicrobial low-density polyethylene-based films was evaluated after immersion in isooctane and the effect of temperature (4, 10, or 25 degreeC) on the diffusion rate was evaluated. The kinetics of linalool and methylchavicol release showed a non-Fickian behavior at the lowest temperature. An increase in temperature from 4 degreeC to 25 degreeC resulted in an increase in the diffusion coefficient from 4.2 x 10-13 m2 s-1 to 2.5 x 10-12 m2 s-1 for linalool and from 3.5 x 10-13 m2 s-1 to 1.1 x 10-12 m2 s-1 for methylchavicol. The effect of temperature on the diffusion coefficient followed an Arrhenius-type model (r2 = 0.972) in relation to a time-response function with a Hill coefficient. Activation energies of 57.8 kJ mol-1 ...
This paper presents direct measurements of the aerodynamic forces on the wing of a free-flying, insect-like ornithopter that was modeled on a hawk moth (Manduca sexta). A micro differential pressure sensor was fabricated with micro electro mechanical systems (MEMS) technology and attached to the wing of the ornithopter. The sensor chip was less than 0.1% of the wing area. The mass of the sensor chip was 2.0 mg, which was less than 1% of the wing mass. Thus, the sensor was both small and light in comparison with the wing, resulting in a measurement system that had a minimal impact on the aerodynamics of the wing. With this sensor, the 'pressure coefficient' of the ornithopter wing was measured during both steady airflow and actual free flight. The maximum pressure coefficient observed for steady airflow conditions was 1.4 at an angle of attack of 30"0. In flapping flight, the coefficient was around 2.0 for angles of attack ...
The objective was to study the interaction of a side jet with the incoming supersonic flow and hypersonic flow. Qualitatively same Cp trends have been obtained as found experimentally. Also in aerodynamic coefficients side jet interaction results in additional pitching moment which is because of the high pressure region in upstream of the jet and a low pressure region in the downstream of the jet. Also jet interaction results in the rise in the lift coefficient. Whereas in the incidence case, simulation has been performed for the hypersonic flows over a biconic body with supersonic lateral jet at Mach 9.7 and incidence of 0"o to incidence of -12"o and 12"o. The results obtained were compared with the experimental and CFD code CFL3D results. PAK-3D over predicts the surface pressure as compared to the CFL3D and experimental results, whereas the qualitative trends are the same. Finally the integrated aerodynamic force ...
The authors discuss a two-phase two-component experimental system developed to study enhancement of heat transfer from a vertical chip size heater to surrounding liquid (Freon 113 or Ethanol) due to air jet impingement. Heat transfer coefficient was measured as function of jet velocity, heat flux and the distance between exit of jet tube and heated surface. The injector was placed very close to the hot surface. It was found that the heat transfer was notably enhanced with foreign gas impingement, especially in the cases of small temperature differences between wall and coolant. In fact for higher jet velocities the heat transfer coefficients tended to infinite while the temperature differences between wall and coolant were zero. The heat transfer coefficients decreased with the increasing of heat flux. High-speed camera was used to study the behaviour of the gas bubbles which play very important role in the heat transfer ...
Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation of mechanical properties and coefficient of thermal expansion. ...
The unsteady aerodynamic forces of a model fruit fly wing in flapping motion were investigated by numerically solving the Navier-Stokes equations. The flapping motion consisted of translation and rotation [the translation velocity (u(t)) varied according to the simple harmonic function (SHF), and the rotation was confined to a short period around stroke reversal]. First, it was shown that for a wing of given geometry with u(t) varying as the SHF, the aerodynamic force coefficients depended only on five non-dimensional parameters, i.e. Reynolds number (Re), stroke amplitude (Phi), mid-stroke angle of attack (alpha(m)), non-dimensional duration of wing rotation (Delta tau(r)) and rotation timing [the mean translation velocity at radius of the second moment of wing area (U), the mean chord length (c) and c/U were used as reference velocity, length and time, respectively]. Next, the force coefficients were investigated for a case in which typical ...
Quark Gluon Plasma transport coefficients for heavy quarks and quark-antiquark pairs are computed through an extension of the results obtained for a hot QED plasma by describing the heavy-quark propagation in the eikonal approximation and by weighting the gauge field configurations with the Hard Thermal Loop effective action. It is shown that such a model allows to correctly reproduce, at leading logarithmic accuracy, the results obtained by other independent approaches. The results are then inserted into a relativistic Langevin equation allowing to follow the evolution of the heavy-quark momentum spectra. Our numerical findings are also compared with the ones obtained in a strongly-coupled scenario, namely with the transport coefficients predicted (though with some limitations and ambiguities) by the AdS/CFT correspondence.
The Ludwig-Soret effect, the migration of a species due to a temperature gradient, has been extensively studied without a complete picture of its cause emerging. Here we investigate the dynamics of DNA and spherical particles sub jected to a thermal gradient using a combination of Brownian dynamics and the lattice Boltzmann method. We observe that the DNA molecules will migrate to colder regions of the channel, an observation also made in the experiments of Duhr, et al[1]. In fact, the thermal diffusion coefficient found agrees quantitatively with the experimental value. We also observe that the thermal diffusion coefficient decreases as the radius of the studied spherical particles increases. Furthermore, we observe that the thermal fluctuations-fluid momentum flux coupling induces a gradient in the stress which leads to thermal migration in both systems.
The experimental survey about the heat transfer between the working fluid and the combustion chamber wall with a direct injection diesel engine has shown the production of a soot layer with increasing loads on the combustion chamber wall. Because the combustion process of methanol occurs without the formation of wall deposits, the same engine spark ignitioned with methanol at the same conditions has shown a higher heat transfer coefficient. Because the heat losses do not only depend on the heat transfer coefficient but also on the driving temperature difference between the working fluid and the combustion chamber wall, the methanol engine with corresponding process management showed lower heat losses than the diesel engine at nearly the same load. (orig./HW)
The structural, electronic and optical properties of ZnX and CdX (X = Se, Te and S) are studied using density functional theory by the Wien2k package. The energy band gap, real and imaginary parts of the dielectric function, energy loss function, optical absorption coefficient and reflectivity spectra of these compounds are calculated. The Engel-Vosko approach improves the energy band gaps of ZnX and CdX compounds. The calculated optical parameters are in good agreement with available experimental results, particularly in the Engel-Vosko approach. Furthermore the effect of hydrostatic pressure on the energy band gap, the real and imaginary parts of the dielectric function of these compounds is studied. The first and second order pressure coefficient for the energy band gaps, the static dielectric function and the static reflectivity spectra are calculated.
Reliability analysis is now being used to a large extent for several civil engineering structures. Such analysis has not been used for rockfill dams, the most common dams in Norway. Following work on reliability analysis for breakwaters, reliability analysis was then used to investigate the ability of the stone material on the upstream face of a rockfill dam to withstand wind generated waves. An attempt is made to follow up this work by including discharge overtopping on a rockfill dam in a reliability analysis. This report primarily goes through previous work on the required weight of protective stones on the downstream face of the dam for specified discharges over the dam and also deals with the probability formulation of extreme floods. A failure function with partial coefficients is formulated. But for reasons of economy the calibration of the partial coefficients remains for a next phase of the project. 14 refs., 17 figs.
This study is an attempt to measure the quantities of elements in a composite by irradiating that composite with #gamma#-rays of various energies and detecting the transmitted radiation through the composite. A previous knowledge of the number of the elements and their attenuation coefficients is required. The quantities are calculated by solving the matrix of a linear system of equations. A computer program was developed to select the best combinations of the available energies. Five criteria were established to determine these energy combinations: (i) the determinant of the attenuation coefficient matrix; (ii) the condition number, (iii) the number of times the solution of the matrix leads to acceptable results; (iv) the indicator, (a new concept); (v) the standard deviations of the results. The intended application of this technique in medicine is to measure the bone mineral content of the skeleton. An examination of the error propagation, ...
Abstract In this paper, a new predictive model that can forecast the performance of a vertical axis wind turbine (VAWT) is presented. The new model includes four primary variables (rotor velocity, wind velocity, air density, and turbine power output) as well as five geometrical variables (rotor radius, turbine height, turbine width, stator spacing, and stator angle). These variables are reduced to include the power coefficient (Cp) and tip speed ratio (TSR). A power coefficient correlation for a novel VAWT (called a Zephyr Vertical axis Wind Turbine (ZVWT)) is developed. The turbine is an adaptation of the Savonius design. The new correlation can predict the turbine's performance for altered stator geometry and varying operating conditions. Numerical simulations with a rotating reference f...
The distribution of the alkaline earth elements strontium and barium between the solid phases of phosphates of transition elements of group 4 and chloride melts was studied. The distribution coefficients of strontium and barium were found at T = 700-800/sup 0/C. Phosphates of the type NaM/sub 2//sup (IV)/(PO/sub 4/)/sub 3/, where M/sub (IV)/ represents titanium, zirconium, and hafnium, were used as the solid phases. It was established that there is an enrichment of the precipitates with the distributed components. The distribution coefficient depends on the nature of the solid phase and the temperature. It was suggested that M/sup (II)/ x M/sub 4//sup (IV)/(PO/sub 4/)/sub 6/ is formed in processes of distribution, where M/sup (II)/ represents Sr, Ba.
In this paper, numerical simulation of a concentric tube heat exchanger is presented to determine the convective heat transfer coefficient and friction factor in a smooth tube. Increasing the convective heat transfer coefficient can increase heat transfer rate in a concentric tube heat exchanger from a given tubular surface area. This can be achieved by using heat transfer augmentation devices. This work constitutes the initial phase of the numerical simulation of heat transfer from tubes employing augmentation devices, such as twisted tapes, wire-coil inserts, for heat transfer enhancement. A computational fluid dynamics (CFD) simulation tool was developed with CFX software and the results obtained from the simulations are validated with the empirical correlations for a smooth tube heat exchanger. The difficulties associated with the simulation of a heat exchanger augmented with wire-coil inserts are discussed. (author)
A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a 137Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data...
The Sputter coefficient of accelerated CO{sub 2} cluster ions hitting surfaces of various materials is investigated. For copper it varies proportional to the 2nd power of the energy between 155 and 260 keV. The rate of erosion for different target materials varies by two orders of magnitude from tungsten to PMMA. Diamond is eroded fairly quickly, while aluminum is eroded less than corundum (Al{sub 2}O{sub 3}). No simple correlation of the sputter coefficient on the bulk material properties is found. For copper the angular distribution of sputtered material is measured and found to be following roughly a cosine distribution. By using masks different microstructures have been produced in cobalt-samarium magnets, diamond and glass. (orig.)
The local heat transfer coefficient distribution of a square channel with two opposite ribbed walls was determined. The square channel was connected to a sudden contraction entrance in order to simulate the inlet condition of the turbine blade cooling passages. The test channel was heated by thin stainless steel foils with a thickness of 0.000025 m, and instrumented with 180 thermocouples. The brass ribs of a square cross-section were glued periodically, in line, onto the top and bottom walls of the foil-heated channel in patterns to achieve the desired spacing and angle-of-attack. The local heat transfer coefficients on the smooth side and the ribbed side walls, at the channel entrance and the downstream regions, were measured for eight rib configurations and three Reynolds numbers (Re = 10,000, 30,000, and 60,000).
This paper discusses the link between R&D and productivity across the European industrial and service sectors. The empirical analysis is based on both the European sectoral OECD data and on a unique micro-longitudinal database consisting of 532 top European R&D investors. The main conclusions are as follows. First, the R&D stock has a significant positive impact on labor productivity; this general result is largely consistent with previous literature in terms of the sign, the significance, and the magnitude of the estimated coefficients. More interestingly, both at sectoral and firm levels the R&D coefficient increases monotonically (both in significance and magnitude) when we move from the low-tech to the medium- and high-tech sectors. This outcome means that corporate R&D investment is m...
The US NRC, in its Generic Environmental Impact Statement on uranium milling has specified that the radon flux escaping a uranium mill tailings pile will be reduced to pCi/m/sup 2/ s by application of covering layers of soils and clays. These covers present a radon diffusion barrier, which sufficiently increases the time required for radon passage from the tailings to the atmosphere to allow for decay of /sup 222/Rn within the cover. The depth of cover necessary to reduce the escaping radon flux to the prescribed level is to be determined by calculation, and requires precise knowledge of the radon diffusion coefficient in the covering media. A Radon Attenuation Test Facility was developed to determine rates of radon diffusion through candidate cover materials. This paper describes this facility and its application for determining the influence of physical properties of the soil column on the radon diffusion coefficient.
Absorption spectra of the visible I_2 band of I_2 complexes with Et_2O, Et_2S, and Et_2Se in heptane have been measured up to 3300 bar at 25"0C. The equilibrium constants and volume changes accompanying complex formation, the molar extinction coefficients and the absorption maxima have been estimated. The volume changes were found comparable with those estimated from the X-ray data of the I_2 complexes in the crystalline state. The enhancement of the molar extinction coefficient and the blue shift of the visible I_2 band with increasing pressure have been established. The results suggest a decrease in the bond distance between an n-donor and I_2, compared with the spectroscopic properties of the I_2 complex at 1 bar. The decrease has been estimated as 0.008 nm with increasing pressure up to 3300 bar. (author).
In this paper, the moisture buffering capacity of spruce plywood is measured by recording the change in mass of a test specimen when the air relative humidity (RH) is changed between 33% RH and 75% RH. The aim is to represent diurnal cycles in indoor humidity with 33% RH maintained for 16 h and 75% RH maintained for 8 h. Measurements are taken using two different apparatuses, which provide different convective transfer coefficients between the air and the plywood, and the results are compared to a numerical model for validation. The validated numerical model is then used to investigate the effect of initial conditions, boundary conditions and thickness on the moisture buffering capacity of plywood. The results show that the buffering capacity of plywood depends on the initial conditions and thickness of the plywood as well as the surface film coefficient and humidity cycle. (author)
Experiments have been performed to study the usefulness of several types of plastic foils as filter to separate radon and thoron. Time-integrated alpha-activity measurements have been carried out by using the so-called ''can-technique'' equipped with both LR-115 and CR-39 track detectors. The track density observed on the detectors, taken as a measure of radon activity concentration, has been determined as a function of the thickness of filter foils. The radon permeability and the thoron separation factors have been determined. It is shown that various plastic foils exhibit considerable differences in radon diffusion coefficient owing to their different chemical structures. Among the plastic foils investigated the polyethylene proved to have the highest gas diffusion coefficient.
Unitarity cuts are widely used in analytic computation of loop amplitudes in gauge theories such as QCD. We expand upon the technique introduced in hep-ph/0503132 to carry out any finite unitarity cut integral. This technique naturally separates the contributions of bubble, triangle and box integrals in one-loop amplitudes and is not constrained to any particular helicity configurations. Loop momentum integration is reduced to a sequence of algebraic operations. We discuss the extraction of the residues at higher-order poles. Additionally, we offer concise algebraic formulas for expressing coefficients of three-mass triangle integrals. As an application, we compute all remaining coefficients of bubble and triangle integrals for nonsupersymmetric six-gluon amplitudes.
A nonlinear free boundary-value problem of supercavitating flow past n + 1 hydrofoils is analyzed. To describe the cavities' closure mechanism, the Tulin-Terentev single-spiral-vortex model is employed. The flow domain is considered as the image of an (n + 1)-connected circular domain. The conformal map is constructed in terms of the solutions to two Riemann-Hilbert problems of the theory of symmetric automorphic functions. One of the problems is homogeneous and its coefficients are continuous functions while the second problem is inhomogeneous and has discontinuous coefficients. The exact solutions to the problems are found by using quasiautomorphic and quasimultiplicative analogs of the Cauchy kernel. The case of a single plate is considered in detail and the numerical results are report...
Mitsubishi is developing a new type of accumulator incorporating the technology of fluidics as one of the seeds for the improved safety of the newly constructed pressurized water reactor plants. This accumulator employs a vortex flow control device, called a vortex damper, as a fluidic device to simplify the safety systems. A fundamental experimental study with a one-fifth scale model and confirmation tests with a one-third scale model to develop the vortex damper have been carried out, and satisfactory results have been achieved. The results of the confirmation tests under the prototype pressure conditions agree well with the basic tests. The flow rate ratio can be 5 to 6. The pressure loss coefficient in the large flow rate period is 8. A cavitation factor is the main parameter of the flow rate coefficient.
Real-time object detection is one of the core problems in computer vision. The cascade boosting framework proposed by Viola and Jones has become the standard for this problem. In this framework, the learning goal for each node is asymmetric, which is required to achieve a high detection rate and a moderate false positive rate. We develop new boosting algorithms to address this asymmetric learning problem. We show that our methods explicitly optimize asymmetric loss objectives in a totally corrective fashion. The methods are totally corrective in the sense that the coefficients of all selected weak classifiers are updated at each iteration. In contract, conventional boosting like AdaBoost is stage-wise in that only the current weak classifier's coefficient is updated. At the heart of the totally corrective boosting is the column generation technique. Experiments on face detection show that our methods outperform the state-of-the-art asymmetric ...
We present an empirical model for periodic variations of diurnal and sub-diurnal Earth rotation parameters (ERPs) that was derived based on the transformation of normal equation (NEQ) systems of Very Long Baseline Interferometry (VLBI) observing sessions. NEQ systems that contain highly resolved polar motion and UT1-TAI with a temporal resolution of 15?min were generated and then transformed to the coefficients of the tidal ERP model to be solved for. To investigate the quality of this model, comparisons with empirical models from the Global Positioning System (GPS), another VLBI model and the model adopted by the conventions of the International Earth Rotation and Reference Systems Service (IERS) were performed. The absolute coefficients of these models agree almost completely within 7.5?...
Individual photophysical parameters of the chromophore of a fluorescent protein mRFP1 and its two mutants (amino-acid substitution at position 66 - mRFP1/ Q66C and mRFP1/Q66S proteins) are determined. For this purpose, apart from conventional methods of fluorimetry and spectrophotometry, nonlinear laser fluorimetry is used. It is shown that the individual extinction coefficients of the chromophore of proteins correlate (correlation coefficient above 0.9) with the volume of the substituted amino-acid residue at position 66 (similar to the positions of the absorption, fluorescence excitation and emission maxima). (laser biology and medicine)
Arsenic and hydrogen ions produced from a mixture of arsine and hydrogen gas were implanted with a dose of 3 x 10{sup 15} As{sup +} ions/cm{sup 2} into silicon using an ion-shower implanter. The dominant ionic species implanted into the silicon were As{sub 2}H{sup +}, AsH{sup +}, H{sub 5}{sup +}, and H{sub 3}{sup +} ions. Arsenic atoms diffused into the silicon with large diffusion coefficients during annealing at 700 and 800 C. However, when the implanted silicon was annealed at 900 C, the arsenic atoms diffused into a deeper region in the silicon with a very small diffusion coefficient that was independent of concentration. (Abstract Copyright [2003], Wiley Periodicals, Inc.)
A thermal analysis of the Omnium-G receiver is presented and the technique is shown to be generally applicable to solar thermal receivers utilizing a directly heated thermal mass. The thermal loss coefficient, including reradiation losses, is calculated and shown to agree quite well with the experimentally measured thermal loss coefficient. The rate of heat transfer to the working fluid is also analyzed and the analysis is used to show that the Omnium-G receiver is well matched to the water/steam working fluid because the steam outlet temperature is almost the same as the receiver temperature. A general procedure for calculating receiver performance is presented. With this procedure, the energy delivery to any working fluid, the delivered temperature of the working fluid, and the pressure drop through the receiver can be determined. An example of the calculation is also presented.
The widespread use of building materials with relatively high radium concentrations may increase population exposure. A method is presented for measuring effective diffusion coefficients and exhalation rates of radon from such materials. Equations for use in the experimental determination of these values are obtained theoretically. The experimental set-up consists of a container which is hermetically sealed to a slab of the building material. Nitrogen is blown through the container and then through an ionization chamber which is connected to an electrometer and X-Y plotter, and the radon concentration is measured continuously. Exhalation rates of radon from some major building materials measured by this method will be used as reference levels. The method can also be used to determine other properties such as porosity. (author).
The maximum fissile fuel production capacity of three conceptual fusion breeder systems is examined on the basis of the dominant isotopic-balance processes. Compact relationships involving system power output, plasma and energy multiplication, and parameters which describe the fuel cycle and neutron spectrum in the blanket are established. It is found that the fusion breeder, as characterized herein, possesses a substantial fissile fuel breeding capacity the extent of which is governed primarily by the neutron spectrum in the conversion blanket and the break-even condition of the plasma.
One requirement of a thermophotovoltaic (TPV) radiator is to efficiently emit photons at high temperatures to TPV cells for conversion to electric power. Because many candidate radiator materials with adequate structural properties display low emissivity, coatings or other surface modifications are required for enhancement of emissivity. Six plasma sprayed coatings and one textured surface demonstrated adequate thermal stability and emittance values of 0.8 or greater. Promising attributes of modified surfaces are identified.
A two-step purification protocol was used in an attempt to separate the constitutive NAD(P)H-nitrate reductase [NAD(P)H-NR, pH 6.5; EC 1.6.6.2] activity from the nitric oxide and nitrogen dioxide (NO(x))...Full Text Available
A new fabrication process is being developed which significantly improves the efficiency of metal-semiconductor solar cells. The resultant effect, a marked increase in the open-circuit voltage, is produced by the addition of an interfacial layer oxide on the semiconductor. Cells using gold on n-type gallium arsenide have been made in small areas (0.17 sq cm) with conversion efficiencies of 15% in terrestrial sunlight.
A series of questions and answers addresses issues related to developing synthetic fuels, including the potential supplies, regulatory road blocks, and development incentives to promote the role of the private sector. Chevron's efforts in the area of synfuels are aimed at shale oil tar sands and coal conversion. The status of these research and development projects and the projected recoverable reserves from each are summarized. (DCK)
Computer simulations and experiments indicate that we can shape the infrared picosecond pulses of the Mark III FEL in amplitude, frequency, and phase. Strongly modulated fundamental and second harmonic pulses have been generated by operating the Mark III FEL in the regime of strong sideband growth. In this paper, we present the results of simulations and experiments for second harmonic generation with fundamental inputs from 2 to 3 {mu}m.
... This is an amount less that the measurement accuracy of even the best meteorological instruments . So, is it really worth committing to 40 years of drastic carbon emissions reductions (which necessarily involves increasing the cost of hydrocarbon fuels in order to reduce fuel consumption, and force an industry-wide conversion to much more expensive alternative energy sources), all so that after nearly all of us are ...
The overall objective of this project is to provide research guidance and quantification of research progress in the areas of direct and indirect coal liquefaction, coal/waste coprocessing, refining of coal-derived liquid fuels, and natural gas conversion. Specifically, the work is divided into two subtasks that relate to whether the technology application is direct or indirect. In subtask (a), Direct Coal Liquefaction technology is the subject of the analyses, and in subtask (b), Indirect Liquefaction, technologies will be evaluated in accordance with the priorities of the COR. Mitretek Systems has been developing detailed computer simulation models of direct and indirect coal and natural gas conversion systems for several years. These models are constantly being updated and improved as more data and better cost information becomes available. These models also include detailed refinery models based on bench-scale upgrading data of coal derived ...
Research is presented on oil and gas technologies, advanced systems, soil remediation and remediation of acid mine drainage, applied science research in plastics and petroleum coprocessing, and fossil fuel and hydrocarbon conversion using a hydrogen rich plasmas.
Research is presented on oil and gas technologies, advanced systems for fossil fuels, environmental technologies for remediation and waste management, applied energy science on heavy oil and plastics coprocessing, and fossil fuel and hydrocarbon conversion using hydrogen rich plasma.
Single and binary metal molybdates, supported on silica (80 wt% active phase/20 wt% SiO{sub 2}), having the formula AMoO{sub 4}, where A = Ni, Co, Mg, Mn, and/or Zn, and some ternary molybdates having the formula Ni{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4}, where X = P, Bi, Fe, Cr, V, and Ce, were investigated for the oxydehydrogenation of propane to propylene. The reaction is catalytic and is first order in propane disappearance, consistent with the abstraction of a methylene hydrogen being the rate limiting step. Propane conversion and yields of propylene produced vary greatly with the choice of the A metal of the molybdate and the surface area of the catalyst. At 560{degrees}C and atmospheric pressure, the highest propane conversion and highest propylene yields are obtained with NiMoO{sub 4}/SiO{sub 2} (16% at 27% conversion), closely followed by Ni{sub 0.5}Co{sub 0.5}MoO{sub 4}/SiO{sub 2}. The molybdenum content of ...
This book is organized under the following headings: Electrohydrodynamic heat transfer augmentation; Forced convection augmentation and heat transfer control; Turbulent heat transfer; Thermal problems in the environment; Energy conversion systems; Measurement, visualization, and imaging; Thermal problems in space technology; and Thermal properties.
The NREL Sensitized Solar Cell (SSC) Core Program supports the Solar America Initiative by: (1) targeting new devices and processes for commercialization by 2015 that are less expensive, more efficient, highly reliable, and environmentally benign; (2) collaborating with DOE OS/BES to conduct basic research targeting breakthroughs in key areas, such as ultra-high efficiency and/or ultra-low cost materials and devices.
Single and binary metal molybdates of the formula AMoO{sub 4}, where A=Ni, Co, Mg,Mn and/or Zn, were investigated for the oxydehydrogenation of propane to propylene, as well as some ternary molybdates of the formula NiO{sub 0.45}Co{sub 0.45}X{sub 0.066}MoO{sub 4} where X=P, Bi, Fe, Cr, V and Ce. All catalysts were supported on SiO{sub 2} with an active phase/support ratio of 80/20 (wt%). The reaction is catalytic and not a gas phase initiated reaction. It is first order in propane, consistent with the abstraction of the methylene hydrogen being the rate limiting step. Propane conversions and propylene yields vary greatly depending on the metal of the molybdate and surface area of the catalyst. Highest propylene yields (16% at 26.6% propane conversion) are obtained with NiMoO{sub 4}/SiO{sub 2}. Conversion and yield are significantly influenced by the molybdenum content of the compositions. The effect is biggest in the nickel ...
A physical model of free-electron laser (FEL) amplifier with variable-parameter wiggler magnets for one-dimensional numerical simulation is presented and a numerical example is given. The wiggler parameters, efficiency of energy conversion between electron beam and laser field, laser intensity, phase-space distributions and energy spectrum of electrons are computed. The period of synchronous oscillation and saturation value of laser intensity agree with estimated one.
This paper describes the conversion from an existing production control computer, an SEL 840, to a DEC VAX 11/780. The plan is to add a layer of hardware to accomplish a smooth and gradual transition from the 840 to the VAX while leaving the underlying equipment unchanged. The architecture of the control system software is discussed for a large linear accelerator from the standpoint of its requirements and the particular design philosophy chosen.
The catalytic dehydration of methanol to dimethyl ether was investigated for application on-board a methanol fuelled vehicle. Several catalysts have been tested in a fixed bed reactor. Our approach is to develop a small and efficient reactor converting liquid MeOH under pressure and at low reaction temperatures. (author) 2 figs., 5 refs.
Separate abstracts were prepared for 20 papers in this conference report and includes all papers in the ''engineering'' section (program E). Ocean thermal energy conversion (OTEC), moorings, cables, corrosion protection, corrosion testing, coatings, offshore platforms, pipelines, OTEC models and pilot plants, and energy transfer are topics discussed.
We report an observation of a delayed all-optical routing/switching phenomenon based on ultraslow group velocity of light via nondegenerate four-wave mixing processes in a defected solid medium. Unlike previous demonstrations of enhanced four-wave mixing processes using the slow light effects, the present observation demonstrates a direct retrieval of the resonant Raman-pulse excited spin coherence into photon coherence through coherence conversion processes.
It is shown that low-frequency elastic vibrations of near-surface planar defects cause high-frequency ultrasonic radiation in surrounding air. The frequency conversion mechanism is concerned with contact nonlinearity of the defect vibrations and provides efficient generation of air-coupled higher-order ultraharmonics, ultrasubharmonics, and combination frequencies. The nonlinear air-coupled ultrasonic emission is applied for location and high-resolution imaging of damage-induced defects in a variety of solid materials.
Elastic depth imaging of both P-wave and S-wave prestack seismic reflection data is formulated as a degraded form of Kirchhoff migration known as Wavepath Migration (WM). Applications to the SEG/EAGE salt model show that the method is sufficiently versatile anti relaitively inexpensive. It handles S-wave data with at least the same accuracy as Pwave data when local mode conversions are removed. WM also provides an understanding of multi-mode illumination.
An ``energy snapshot`` article is included on housing characteristics in 1993 (survey of 7,111 households). The rest of the document is divided into: energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, international energy, and appendices (conversion factors, CO2 emission factors from coal, index, glossary).
The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.
This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.
An economical way to reduce the deleterious effects of titanium, one of the impurities present in metallurgical grade silicon material, is disclosed. By adding copper to approximately the same concentration level of the titanium during the melting process, the conversion efficiency will be restored to about 99.3% of what it would have been if the single crystal silicon had been grown free of titanium impurities.
The special features of prostaglandin biochemistry, of importance for investigation of the possible physiological roles of prostaglandins, are briefly reviewed. The formation of prostaglandins and related compounds from endogenous and exogenous arachidonic acid in homogenates of human gastric mucosal and muscle-serosal layers is described. These preliminary data seem to indicate that a low conversion of exogenous precursor does not necessarily mean that the capacity of the tissue to synthesize prostaglandins from endogenous precursor is low.
During the period covered by this report research has been concerned with the study of photo-induced electron transfer reactions from porphyrins to acceptor molecules with time-resolved Electron Paramagnetic Resonance (EPR) methods. Excited-state electron transfer reactions are of importance from a fundamental point of view and in connection with applications in homogeneous and heterogeneous photosensitization, photopolymerization, and solar energy conversions. For this reason, the study of photo-induced electron transfer reactions is of considerable interest.
Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 ( +- 20) K with a (SSB) conversion loss of 2.4 ( +- 0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.
This report provides overall state and national information on the quantity, availability, and costs of current and potential feedstocks for ethanol production in the United States. It characterizes end uses and physical characteristics of feedstocks, and presents relevant information that affects the economic and technical feasibility of ethanol production from these feedstocks. The data can help researchers focus ethanol conversion research efforts on feedstocks that are compatible with the resource base.
Heterodyne detection with a point-contact Josephson junction has been investigated both experimentally and theoretically. The measured performance of the device at 36 GHz is in good agreement with the theory. By operating vanadium point contacts at 1.4 K, the authors have achieved a single-sideband (SSB) mixer noise temperature of 54 K with a conversion gain of 1.35 and a signal bandwidth on the order of 1 GHz. A potentially impressive performance for these devices at submillimeter wavelengths can be extrapolated from the results.
The principle of operation of shaft furnaces is explained and demonstrated in four practical examples. The conditions and parameters determining coke conversion in the combustion zone and in the Boudouard reaction range are described. The combustion process is treated as a whole while the reduction process is discussed separately for the blast furnace, the cupola furnace, and the shaft furnace. The possibilities describing the Boudouard reaction as a function of the temperature level are discussed and consequences are derived for further experimental and theoretical studies.
Coal may be used to generate electrical energy by any of several processes, most of which involve combustion or gasification. Combustion in a coal-fired boiler and power generation using a steam- cycle is the conventional conversion method; however, total energy conversion efficiencies for this type of process are only slightly over 30{percent}. Integration of a gas-cycle in the process (combined cycle) may increase the total conversion efficiency to 40{percent}. Conversion processes based on gasification offer efficiencies above 50{percent}. H{sub 2}S is the predominant gaseous contaminant in raw coal gas. Problems arise due to the corrosive nature of H{sub 2}S on metal components contained in these cycles. Because of this, H{sub 2}S concentrations must be reduced to low levels corresponding to certain power applications. An advanced process for the separation of hydrogen sulfide (H{sub 2}S) from coal ...
The proceedings contain 21 papers arranged under the following topical sections: Exploration technology (4 papers); Reservoir technology (5 papers); Energy conversion technology (8 papers); Drilling technology (2 papers); and Direct use and geothermal heat pump technology (2 papers). An additional section contains a report on a workshop on dual-use technologies for hydrothermal and advanced geothermal reservoirs.
Context: The Balanced Budget Act (BBA) of 1997 allowed some rural hospitals meeting certain requirements to convert to Critical Access Hospitals (CAHs) and changed their Medicare reimbursement from prospective to cost-based. Some subsequent CAH-related laws reduced restrictions and increased payments, and the number of CAHs grew rapidly. Purpose: To examine factors related to hospitals' decisions to convert and time to CAH conversion. Methods: Eighty-nine rural hospitals in Iowa were characterized and observed from 1998 to 2005. Cox proportional hazards models were used to identify the determinants of time to CAH conversion. Findings: T-test and one-covariate Cox regression indicated that, in 1998, Iowa rural hospitals with more staffed beds, discharges, and acute inpatient days, higher operating margin, lower skilled swing bed days relative to acute days, and located in relatively high density counties were more likely to convert later or not ...
Glucoamylase and pullulanase were immobilized on reconstituted bovine-hide collagen membranes using the covalent azide linkage method. A pretanning step was incorporated into the immobilization procedure to enable the support matrix to resist proteolytic activity while accommodating an operating temperature of 50 degrees C. The immobilized glucoamylase and pullulanase activities were 0.91 and 0.022 mg dextrose equivalent (DE) min(-1) cm(-2) of membrane, respectively. Immobilized glucoamylase had a half-life of 50 days while the immobilized pullulanase had a half-life of 7 days. This is a considerably improved stability over that reported by other researchers. The enzymes were studied in their free and immobilized forms on a variety of starch substrates including waxy maize, a material which contains 80% alpha-1-6-glucosidic linkages. Substrate concentrations ranged from 1% to a typical commercial concentration of 30%. Conversion efficiencies of 90-92% DE were ...
It is shown that recuperator in which the thermal energy of particles is transformed into electric oue under drift in crossed fields is naturally coupled with dragontype magnetic confinement system, so the recuperation process can be initiated in the dragon magnetic field. A number of questions occuring under analysis of recuperator-dragon system is considered, including the dynamics of particle transfer to the recuperator, the share of particles entering the recuperator, the effect of rotational transform and the recuperation efficiency.
A) diffuse bilayer, B) spontaneously formed multilayer, and C) vertically homogenous thin films, are fabricated. The photocurrent/voltage performance is compared and it is found that the self-stratified structure (B) yields the highest energy conversion efficiency. (Abstract Copyright [2009], Wiley Periodicals, Inc.)
New measurements of relative gamma-ray emission probabilities in the decay of [sup 101]Mo and [sup 101]Tc are reported. Previously published conversion-electron data have been used along with the gamma-ray data to formulate self-consistent decay schemes. (orig.)
New measurements of relative gamma-ray emission probabilities in the decay of "1"0"1Mo and "1"0"1Tc are reported. Previously published conversion-electron data have been used along with the gamma-ray data to formulate self-consistent decay schemes. (orig.).
The crabbing of an incident photon beam from a laser, and the electron beam with which it interacts at the conversion point, is shown to have the same efficiency as in head-on Compton scattering, but with the advantages of a crossing geometry. The resulting #gamma#-ray beam is also crabbed, which allows for a crossing collision point, while maintaining the luminosity at the same value it would have in a head-on collision.
The crabbing of an incident photon beam from a laser, and the electron beam with which it interacts at the conversion point, is shown to have the same efficiency as in head-on Compton scattering, but with the advantages of a crossing geometry. The resulting {gamma}-ray beam is also crabbed, which allows for a crossing collision point, while maintaining the luminosity at the same value it would have in a head-on collision. ((orig.)).
The crabbing of an incident photon beam from a laser, and the electron beam with which it interacts at the conversion point, is shown to have the same efficiency as in head-on Compton scattering, but with the advantages of a crossing geometry. The resulting #gamma#-ray beam is also crabbed, which allows for a crossing collision point, while maintaining the luminosity at the same value it would have in a head-on collision. ((orig.)).
Simulated atmospheric corrosion studies were performed to determine the corrosion protection provided by galvanized zinc coatings on depleted uranium, U-0.75 Ti alloy, and U-6 Nb alloys. The accelerated ASTM tests consisted of exposing the galvanized samples to aqueous and aqueous chloride environments. The test results showed that anodic protection was provided by the electronegative zinc coatings on uranium and uranium alloys. Treating zinc with chromate conversion coatings also provided more protection.
In this small review, the following general properties of the Compton scattering as the basic process for creating {gamma}{gamma} colliders in the scheme suggested in Ginzburg et al. (Inst. Nucl. Phys. 34 (1981) 514; Nucl. Instr. and Meth. 205 (1983) 47) are considered: kinematics, photon spectrum, angular distribution, polarization of the final photons and electrons as well as some related problems.
The nr1 soybean (Glycine max [L.] Merr.) mutant does not contain the two constitutive nitrate reductases, one of which is responsible for enzymic conversion of nitrite to...Full Text Available
Communicating and collaborating online are becoming common requirements in education. The specialized notations and symbols necessary for some content areas where mathematical expressions are part of the conversation require that users select appropriate communication tools. The purpose of this article is to describe tools that can be used for online, asynchronous or synchronous communication involving mathematical expressions.
The development of a synthetic fuels industry in Australia is described in the context of overall energy policy. The national coal liquefaction research program is directed at three main routes to liquid fuels: hydroliquefaction, pyrolysis and indirect liquefaction. Australia is also contributing to technology development and assessment programs in cooperation with other countries, in particular Federal Republic of Germany and Japan.
A process is provided for conducting organic compound conversion over a catalyst composition comprising a supported crystalline zeolite having a high initial silica-to-alumina mole ratio, said supported zeolite being prepared by compositing said crystalline zeolite with alumina, reacting the composite with a particular hydrogen fluoride solution in a specified way, drying the hydrogen fluoride reacted composite, treating the dried composite by hydrolysis, ammonolysis and/or by contact with an ammonium salt solution, and calcining the resulting material.
Five barrels of a Wilsonville process derived solvent (V-1074) from Black Thunder coal were obtained. This material boils within the preferred gas oil range, is more aromatic than previous solvents, and will therefore be used for the bench unit studies. Several repeat runs were performed in the autoclave to confirm the results of the matrix study. In addition, runs were carried out with different catalysts, with agglomerates and with the V-1074 solvent. The results of the autoclave runs were analyzed with respect to coal conversion, CO conversion, oil yield, hydrogen consumption and oxygen removal. It was concluded that the best operating conditions for the first stage operation was a temperature of at least 390{degrees}C, residence time of at least 30 minutes, cold CO pressure of at least 600 psig and potassium carbonate catalyst (2% wt on total feed). The data also indicated however, that the coal conversion goes through ...
Prostaglandin E2 (PGE2) has been shown to increase the synthesis of hyaluronic acid in cultured fibroblasts by increasing the activity of hyaluronate synthetase, a group of plasma membrane-bound synthetic enzymes. We examined whether PGE2 also increased the activity of those enzyme systems involved in the synthesis of sulfated glycosaminoglycan in the human embryonic lung fibroblast. Exposure of cells to PGE2 resulted in dose-dependent increases in glucosamine incorporation into all sulfated glycosaminoglycan subtypes. PGE2 at 10(-7) mol/L increased total glycosaminoglycan per dish to 21.6 +/- 3.1 micrograms versus 12.0 +/- 2.5 micrograms in control untreated cultures. Stimulation of endogenous PGE2 production by bradykinin had a similar effect on glycosaminoglycan synthesis. To examine whether PGE2 affected sulfated glycosaminoglycan protein core production, cells were labeled with tritiated glucosamine in the presence of cycloheximide. Under ...
Warm-intermediate inflationary universe models in the context of braneworld cosmologies, are studied. This study is done in the weak and strong dissipative regimes. We find that, the scalar potentials and dissipation coefficients in terms of the scalar field, evolves as type-power-law and powers of logarithms, respectively. General conditions required for these models to be realizable are derived and discussed. We also study the scalar and tensor perturbations for each regime. We use recent astronomical observations to constraint the parameters appearing in the braneworld models.
We consider a particle that is subject to a constant force and scatters inelastically on a vibrating periodically corrugated floor. At small friction and for small scatterers the dynamics is dominated by resonances forming spiral structures in phase space. These spiral modes lead to pronounced maxima and minima in the diffusion coefficient as a function of the vibration frequency, as is shown in computer simulations. Our theoretical predictions may be verified experimentally by studying transport of single granular particles on vibratory conveyors.
An original evaluating method of gain degradation has been found for neutron irradiated transistors. It establishes a correlation between degradation and the product of two coefficients: spectra factor and an electrical parameter which is measured or directly deduced from manufacturer's data. Equivalence for several type of spectra (fission, 14MeV and degradation sensitivity to electrical parameters values of individual components of a batch are obtained.
The polarization characteristics of spontaneous radiation from relativistic electrons moving through helical and planar wiggler fields are evaluated for imperfect beam injection. Maximum coherent gain in free-electron laser systems are seen to occur in optical fields having these polarization characteristics rather than those of the wiggler magnets. Coupling coefficients for an electron beam skewed at an angle to the optical mode are presented.
An apparatus allowing the photoexcitation of barium atomic beam over its whole surface is described. This photoexcitation is achieved by another barium spectrum emitted up steam of the beam by a cathodic out-flow produced at the exit oven. The fluorescence spectrum is studied in detail as well as the influence of different parameters, such as oven temperature, current intensity of the outflow, and excitation depth. A calculation shows how to determine Einstein coefficient, oscillator strengths and atomic lifetimes from our experimental measurements.
A study of the 150-300 keV proton beam transmission through glass (borosilicate) tapered capillaries with different diameters of the input and output of the capillary was performed. The focusing effect was observed. The areal density of the transmitted beam is enhanced by approximately 20 times. It was shown that changing a taper angle from 0.5 deg to 1.7 deg evidences the increase of the transmission coefficient more than by 300 times keeping the initial energy spectrum of ions. (author)
Transient enhanced diffusion in boron-implanted silicon is interpreted as being due to the fact that during rapid thermal annealing a relaxation process takes place, associated with quasi-chemical reactions including defects. A simple analytical model makes it possible to describe the annealing mechanism on a microscopic scale in terms of reaction-diffusion processes. The measured dependences of the boron diffusion coefficient of the enhanced diffusion on time, temperature and implantation energy are satisfactorily explained. (author).
Transient enhanced diffusion in boron-implanted silicon is interpreted as being due to the fact that during rapid thermal annealing a relaxation process takes place, associated with quasi-chemical reactions including defects. A simple analytical model makes it possible to describe the annealing mechanism on a microscopic scale in terms of reaction-diffusion processes. The measured dependences of the boron diffusion coefficient of the enhanced diffusion on time, temperature and implantation energy are satisfactorily explained. (author).
The basic design of a system installed in the Columbus, Ohio Zoo is described. The distribution system is described in detail. The control system is microprocessor controlled, with about 50 monitoring points. Preliminary evaluations have indicated that the system can operate with an overall coefficient of performance in excess of 3.5. 1 figure.
A pulsed field gradient spin echo sequence has been incorporated in a nuclear magnetic resonance (NMR) imaging experiment to provide an image contrast dependent on local molecular self-diffusion. The...Full Text Available
A mathematical model is proposed for three-phase filtering which is a particular case of a more general model of filtering multiple component mixtures and makes it possible to describe three-phase filtering flows under conditions where the pressure of saturation is variable in time and in space. In the proposed model, the system of unknown functions is selected so that it makes it possible to trace fairly simply the pressure of saturation and to compute the corresponding equation coefficients.
X-ray results on the lattice parameters, molar volume and thermal expansion coefficients of solid ortho-deuterium for the region from 2 K to the melting point are reported. It is found that the thermal expansion of ortho-deuterium crystals, similarly to parahydrogen is essentially anisotropic near the melting temperature. The vacancy density at the triple point is estimated. Some thermodynamic characteristics of ortho-deuterium are calculated and temperature dependences of heat capacity at constant volume, isothermal compressibility and Gruneisen constant are analyzed.
We construct a chaotic inflation model in which the Higgs fields play the role of the inflaton in the singlet extension of the supersymmetric standard model. The key idea is to impose a shift symmetry on the D-flat direction Hu Hd in the Kahler potential. The model is a realization of the recently proposed running kinetic inflation, in which the coefficient of the kinetic term grows as the inflaton field. The inflaton potential depends on the structure of the Higgs sector. For instance, the inflaton potential is proportional to phi^{2/3} during inflation in the NMSSM.
Natural radioactive materials were used for detector calibration. We found that KCl is a very suitable material for this purpose. The efficiency curve shape was derived by using {gamma} ray lines of {sup 214}Bi normalised using a known quantity of KCl in the same geometry. The best fit was found by the least squares method. The summing correction coefficients for {sup 214}Bi are determined. (orig.).
Natural radioactive materials were used for detector calibration. We found that KCl is a very suitable material for this purpose. The efficiency curve shape was derived by using #gamma# ray lines of "2"1"4Bi normalised using a known quantity of KCl in the same geometry. The best fit was found by the least squares method. The summing correction coefficients for "2"1"4Bi are determined. (orig.).
The estimation of numerical values of the mean distance of closest approach of ions, a, of heavy metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.
Based on results from recent studies of elemental dietary intake and organ or tissue content for adult Chinese men, quoted nationwide elemental concentrations in Chinese soil and newly published national average consumption of dietary foods, values of both transfer coefficients and discrimination factor (DF) for transfer from soil via the diet to both critical organs and the whole body have been calculated for important elements in radiation protection, including alkaline earths, alkali metals, rare earths and other related elements. These calculations have used both the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) model and the DF method. In the UNSCEAR model, the basic parameters used to describe the transport of radionuclides are the transfer coefficients P_i_j, which describe the relationship of concentrations or other amounts between compartment i and the following compartment j, whereas the DF is the ...
Donnan dialysis with ion-exchange membranes was studied under various kinds of experimental conditions using ions of different valences. The diffusion coefficients (D{sub d}) of various kinds of ions in the ion-exchange membrane were obtained by curve fitting an equation derived from the mass balance to three kinds of Donnan dialytic experiments. It was found that the value of D{sub d}/D{sub s} using D{sub d} of monovalent ions in Donnan dialysis with a set of monovalent feed ions and bivalent driving ions was 1/175, where D{sub s} represents a diffusion coefficient in solution. D{sub s} was calculated from the Nernst-Einstein equation substituted by the ionic conductance of ions at infinite dilution in water. Using D{sub d} of bivalent ions in Donnan dialysis with the same set led to a D{sub d}/D{sub s} value of 1/438. Moreover, using D{sub d} in Donnan dialysis with the same set, the value of D{sub d}/D{sub e} was kept constant at 0.4 (D{sub ...
The kinetic parameters, ..cap alpha.. the coupling coefficient and tau-bar the mean neutron transit time have been determined using a reactor oscillator on the coupled-core of the Queen Mary College research reactor. By using correlation techniques it has proved possible to use detectors small enough to be inserted in the fuel tanks. It is shown that the simplified Baldwin model with one-group diffusion theory is inadequate to describe the kinetic behaviour and the experimentally-determined parameters are dependent upon the positioning of the detectors.
The paper presents a sequential procedure for coordinated stabilization of a multimachine power system with arbitrary complexity of the system model. The most effective machine to be equipped with a power system stabilizer is identified using eigenvalue analysis. The selection is based on the sensitivity of critical eigenvalues to increases in the coefficient of a damping term which is inserted in each equation of motion, in succession. The method is applied to a three-machine system and simulation studies show appreciable improvements in the small disturbance stability of the system.
Results on defect structure study and degree of molybdenum radiation hardening irradiated by fission neutrons and medium energy alpha-particles are presented. It is shown that molybdenum irradiation by alpha-particles and neutrons leads to different degree of material hardening for the same damage level. It is established that molybdenum radiation hardening is mainly defined by radiation defect clusters visible in electron microscope whose coefficient of rigidity depends on their size. 5 refs.; 6 figs.; 2 tabs. (author).
The effect of finite gyroradius on the current diffusive ballooning mode is examined. Starting from the reduced MHD equations including turbulent transports, coupling with drift motion and finite gyroradius effect of ions, we derive a ballooning mode equation with complex transport coefficients. The eigenfrequency, saturation level and thermal diffusivity are evaluated numerically from the marginal stability condition. Preliminary results of their parameter dependence is presented. (author)