British Library Electronic Table of Contents (United Kingdom)

Macroautophagy is a multistep, vacuolar, degradation pathway terminating in the lysosomal compartment, and it is of fundamental importance in tissue homeostasis. In this review, we consider macroautophagy in the light of recent advances in our understanding of the formation of autophagosomes, which are double-membrane-bound vacuoles that sequester cytoplasmic cargos and deliver them to lysosomes. In most cases, this final step is preceded by a maturation step during which autophagosomes interact with the endocytic pathway. The discovery of AuTophaGy-related genes has greatly increased our knowledge about the mechanism responsible for autophagosome formation, and there has also been progress in the understanding of molecular aspects of autophagosome maturation. Finally, the regulation of au...

British Library Electronic Table of Contents (United Kingdom)

An examination of the kinetics of the alkylation of anisole with 1-hexene and 1-hexanol to produce alkylates over zeolite H-beta is presented. Anisole alkylation is found to occur by a set of parallel reactions when hexene is used as the alkylating agent. When hexyl alcohol is the alkylating agent, the reaction follows a multi-step parallel-series mechanism to form monoalkylates and dihexylether. With 1-hexene, a group of isomeric alkylates, viz., ortho-2-hexyl anisole (2-OHA), ortho-3-hexyl anisole (3-OHA), para-2-hexyl anisole (2-PHA), and para-3-hexyl anisole (3-PHA) was obtained. With hexanol, the olefin (hexene) and dihexyl ether were obtained additionally. The influence of process parameters like temperature, catalyst quantity, and alkylating agent on reaction behavior is reported.

Energy Technology Data Exchange (ETDEWEB)

This book contains over 20 selections. Some of the titles are: Continuum damage mechanics studies on the dynamic fracture of concrete; Dynamic compressive strength of cementitious materials; Rate-sensitivity of mode I and mode II fracture concrete; and An impact damage model of concrete.

UK PubMed Central (United Kingdom)

Despite a complex cascade of cellular events to reconstruct the damaged extracellular matrix, ligament healing results in a mechanically inferior scarred ligament. During normal healing, granulation...Full Text Available

UK PubMed Central (United Kingdom)

Physiological bone remodeling is a highly coordinated process responsible for bone resorption and formation and is necessary to repair damaged bone and to maintain mineral homeostasis. In addition to...Full Text Available

UK PubMed Central (United Kingdom)

Hepatic damage occurs in males and ovariectomized (OVX), not in proestrus (PE), females following trauma-hemorrhage (T-H). The mechanism responsible for hepatoprotection remains unknown. We hypothesized...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We describe a model of damage in rf cavities and show how this damage can limit cavity operation. We first present a review of mechanisms that may or may not affect the ultimate fields that can be obtained in rf cavities, assuming that mechanical stress explains the triggers of rf breakdown events. We present a method of quantifying the surface damage caused by breakdown events in terms of the spectrum of field enhancement factors, Beta, for asperities on the surface. We then model an equilibrium that can develop between damage and conditioning effects, and show how this equilibrium can determine cavity performance and show experimental evidence for this mechanism. We define three functions that quantify damage, and explain how the parameters that determine this performance can be factored out and measured. We then show ...

International Nuclear Information System (INIS)

Iron is one of the main constituents of stainless steel which is used as a structural material in nuclear reactors. In fast and conceptual fusion and fusion-fission hybrid systems the primary energy range of neutron interaction lies between 1 and 20 MeV which opens up several reaction channels. The reaction cross-sections in this energy range are important for dosimetry, radiation damage, neutronics and safety studies of nuclear reactors. Keeping this in view Nuclear Data Section of the International Atomic Energy Agency has sponsored a Research Co-ordination Programme on Methods for the Calculation of Fast Neutron Nuclear Data for Structural Elements. Under this programme we propose to study (n,n'), (n,2n), (n,3n), (n,p), (n,np), (n,pn), (n,#alpha#), (n,n#alpha#), (n,#alpha#n) and (n,#gamma#) reaction cross-sections. Besides these, total, elastic and discrete level inelastic scattering cross-sections, angular distributions of neutron production cross-sections, ...

Science.gov (United States)

Some aspects of molecular mechanisms common to radiation and chemical carcinogenesis are discussed, particularly the DNA damage done by these agents. Emphasis is placed on epidemiological considerations and on dose-response models used in risk assessment to extrapolate from experimental data obtained at high doses to the effects from long-term, low-level exposures. 3 references, 6 figures. (ACR)

UK PubMed Central (United Kingdom)

BackgroundDNA repair is the general term for the collection of critical mechanisms which repair many forms of DNA damage such as methylation or ionizing radiation. DNA repair has...Full Text Available

International Nuclear Information System (INIS)

Shadow effect was used for investigating damage of uranium dioxide monocrystal. The dependence of shadow minimum parameters on fluence of "2"2Ne ions with 172 MeV energy was followed when detecting fission fragments. Ion dose responsible for sufficient microdamage of lattice structure, included into the classification of heavy ion damage effect on monocrystals was determined. The problem of radiation intensity effect on the character of occurred damages was studied. It was established that macroscopic sample failure, caused by generation of considerable mechanical stresses in monocrystal under beam effect could be observed along with microdamages of lattice structure at ion flux density >10"1"2 cm"-"2Xs"-"1.

UK PubMed Central (United Kingdom)

BackgroundSearching for approximate patterns in large promoter sequences frequently produces an exceedingly high numbers of results. Our aim was to exploit biological knowledge for...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Measurements were made of the cross sections for the /sup 27/Al(/sup 16/O,/sup 15/N)/sup 28/Si, /sup 89/Y(/sup 15/N,/sup 16/O)/sup 88/Sr and /sup 89/Y(/sup 27/Al,/sup 28/Si)/sup 88/Sr reactions at energies near and below the Coulomb barrier. The first reaction required separate measurements of the transfer to elastic cross section ratio for particular charge states, the charge state distribution for /sup 27/Al and /sup 28/Si ions, and the absolute elastic scattering cross section for the /sup 27/Al + /sup 16/O system. The ratio measurement required the combined use of two relatively new scientific instruments: the momentum filter and the Bragg curve spectrometer. The latter two transfer measurements were performed using the same setup involving surface barrier detectors at backward angles. Additional elastic scattering data for the /sup 15/N + /sup 28/Si, /sup 89/Y + /sup 15/N, /sup 89/Sr + /sup 27/Al, and /sup 88/Sr + /sup 28/Si systems was collected to provide entrance and exit ...

Energy Technology Data Exchange (ETDEWEB)

In the power station West Block 2 at Voerde (Federal Republic of Germany), cracks in the final stage of the shaft were determined at the ND1 rotor of the 350 MW condensation tube was determined. A purely mechanical preparation of the crack was not possible due to the depth of the crack. A substitute rotor was not available. A repair solution was developed covering a welding of a new shaft section to the existing rotor. The authors of the contribution under consideration report on the damage, cause of the damage, repair solution and the process of repair.

Energy Technology Data Exchange (ETDEWEB)

This work contains 27 chapters which cover recent advances in fracture mechanics applied to cement-based composites: concrete, reinforced concrete, and fiber reinforced concrete. The book, based on a NATO Advanced Study Institute, is a comprehensive survey of treating nonlinearity associated with crack growth in brittle materials such as cement composites, rocks and ice. The book is divided into 8 major themes: advances in nonlinear fracture mechanics; fracture processes; numerical modelling of fracture; experimental methods of determining fracture parameters; damage and continuum modelling; strain-rate and dynamic effects of crack propagation; stress-corrosion, time and temperature effects on fracture; and implications for concrete structures.

Energy Technology Data Exchange (ETDEWEB)

Blades of modern steam turbines are designed for high efficiency and operational safety. Modern computer programs enable optimisation of design but factors like manufacturing, assembly, operation and downtimes still play an important role. Damage statistics show that blade damage still quite frequent. Selected cases from the Allianz damage assessment centre show some of the more frequent damage mechanisms. Damage is often caused when several factors come together. Prevention of follow-up damage requires early identification of beginning damage.(orig.) [German] Die Auslegung der Beschaufelung moderner Dampfturbinen hat die Vorgabe, einen hohen Wirkungsgrad bei gleichzeitig hoher Betriebssicherheit zu erreichen. Mit den heute zur Verfuegung stehenden Rechenprogrammen ist eine entsprechende Optimierung realisierbar. Fuer ...

International Nuclear Information System (INIS)

The use of primary electron counting techniques as an alternative to the more usual parallel plate avalanche chamber that has been employed in soft x-ray scattering experiments is being investigated at the National Synchrotron Light Source. The theoretical aspects of primary electron counting and motivation behind building a primary electron counting detector are described, as well as characteristics and future improvements of the device constructed at the NSLS. The detector consists of a low electric field drift region and a low pressure multistep avalanche region which can be operated with two or three stages of electron multiplication. The device has worked well in extensive tests as a simple parallel plate avalanche chamber, providing energy resolutions of 58% and 43% at 277 and 500 eV, respectively. Operated as a primary electron counter, preliminary results show an energy resolution of 38% at 500 eV.

Energy Technology Data Exchange (ETDEWEB)

Due to changed operational conditions and because of the increasing age of several hydro power plant components, there is an increasing risk of damages and the control of degradation mechanisms is of increasing significance. Therefore lifetime considerations for safety relevant components in pumped-storage plants become more and more important. The development of a lifetime management system, in conjunction with monitoring systems and specific surveillance for a group of pumped-storage power plants of different ages and in a wide range of power output is presented. The special focus is on the impact of fatigue strength considerations within this framework. The applied procedure will be described for typical mechanical components in pumped-storage plants exemplarily. (orig.)

Energy Technology Data Exchange (ETDEWEB)

A high voltage self-blowing circuit breaker with closing resistors is equipped with an auxiliary contact inserted in the trip control circuit of an electrical circuit breaker. The auxiliary contact is actuated by the mechanical control rod of the circuit breaker in such a way as to prevent any operator closing error. A high-speed mechanism is inserted in the link system connecting the control rod and the auxiliary contact, with dead travel to delay closing of the auxiliary contact when a closing operation takes place and to prevent a tripping order from being transmitted too early. Such an early transmission would be liable to cause a flashover on the inserter contacts and damage to the circuit breaker.

Energy Technology Data Exchange (ETDEWEB)

A thesis is presented on improving the understanding of the fatigue properties of wood and fatigue failure mechanisms in the design of wind turbine blades. Three main areas were researched: the effect of R ratio on fatigue life, the effect of moisture on fatigue life and the development of cumulative damage laws. Tests were carried out on mainly four-ply laminates. Recommendations to future work are outlined. (U.K.).

Science.gov (United States)

The epileptogenic and neurodegenerative effects of gamma-dendrotoxin, from Dendroaspis angusticeps, a specific blocker of a non-inactivating, voltage-sensitive K+ channel, were studied after focal injection into one dorsal hippocampus in rats pretreated with CGP040116, a N-methyl-D-aspartate (NMDA) receptor antagonist, and in rats bearing a monolateral surgical lesion of the Schaffer collaterals whose terminals originate from CA3 pyramids and release glutamate in the CA1 hippocampal area. Administration of 35 pmol gamma-dendrotoxin elicited in all of the treated animals (n=8) bilateral EEG discharges and damage to the hippocampal formation. Quantitation of the damage revealed significant bilateral neuronal cell loss in the CA1, CA3 and CA4 pyramidal cell layers. The lowest dose (0.35 pmol; n=4) of the toxin used did not affect EEG activity and failed to cause significant hippocampal cell loss whereas the 3.5 pmol (n=6) dose caused EEG seizures ...

Energy Technology Data Exchange (ETDEWEB)

High temperature components of power plants are in many cases subjected to variable loading conditions such as cyclic creep or strain cycling. Therefore the cyclic behaviour of important heat resistant steels has been investigated under stress control and to a smaller extent under strain control. The behaviour under cyclic creep rupture conditions was determined in long term experiments covering a wide range of loading conditions. This behaviour can be described with the modified life fraction rule and a factor concept of relative life for single stage cycles and additionally with a multistep hypothesis for multi-stage cycles. The description can be adapted to estimate the life consumption under service type random conditions. The strain cycling behaviour was investigated in regard to the conditions of the heated surface of large components. To simulate this type of loading and to generate long term creep fatigue data, a service type strain cycle was developed. ...

Energy Technology Data Exchange (ETDEWEB)

Slow, unexpected displacements have been experienced in most pressurized water reactor (PWR) surge lines. Sometimes, these displacement lead to gap closure at the pipe whip restraints. These movements occur because of thermal stratification. This movement has the potential to increase stresses to valves, which may exceed the material yield stress. To understand this phenomenon, Framatome, Commissariat a l'Energie Atomique, and Electricite de France have undertaken large programs for the study of (1) thermal-hydraulic tests with a half-scale Plexiglas surge line, (2) thermal-hydraulic computations of permanent states and transients with a two-dimensional model, and (3) mechanical analysis of displacements and computation of fatigue damage due to stratification. This paper deals with the last subject. Avoiding stratification in piping by process modifications is difficult because of the high flow rate needed. Alternative solutions for ...

Energy Technology Data Exchange (ETDEWEB)

The effects of irradiation from a focused ion beam (FIB) system on MOS transistors are reported systematically for the first time. Three MOS transistor technologies, with 0.5, 1, and 3 {mu}m minimum feature sizes and with gate oxide thicknesses ranging from 11 to 50 nm, were analyzed. Significant shifts in transistor parameters (such as threshold voltage, transconductance, and mobility) were observed following irradiation with a 30 keV Ga{sup +} focused ion beam with ion doses varying by over 5 orders of magnitude. The apparent damage mechanism (which involved the creation of interface traps, oxide trapped charge, or both) and extent of damage were different for each of the three technologies investigated.

International Nuclear Information System (INIS)

A Y-Mg-Si-Al-O-N glass was submitted to swift heavy-ion bombardment at GANIL (Caen, France) and the influence of irradiation on the mechanical properties was studied. The mechanical properties of the glass were characterized both before and after irradiation. Changes in hardness, elastic modulus and fracture toughness of the near-surface irradiated layer were determined using indentation techniques. SRIM calculations allowed to estimate the ions penetration range and the energy deposition relative to electronic and nuclear interactions, which can be correlated to the experimental damaged depth. Meyer's hardness and Young's modulus decrease by about 30 %, while fracture toughness is increased by more than 40 %. (authors)

Energy Technology Data Exchange (ETDEWEB)

The paper evaluates standardization of regulations on safety of electrical equipment for underground coal mines in the USSR. Factors increasing hazards of electrical failures of equipment in underground coal mines are analyzed: reduced lighting, increased humidity and dusts, damage caused by falling rocks or damage during haulage in underground workings, installation of electrical equipment in places easily accessible to untrained personnel. Standards on safety of electrical equipment for underground coal mining valid in the USSR are reviewed: the PIRNEh regulations on production of electrical equipment for coal mines developed by the VNIIVEh Institute, and the GOST national standards. International cooperation within the COMECON on safety of mining electrical equipment (the Interelectro Committee of the COMECON) is described. Certification of electrical equipment for coal mines is discussed on the example of electrical insulation types used in ...

International Nuclear Information System (INIS)

This report briefly describes the studies on the mechanism of in vivo DNA repairing by the author in Research Reactor Institute, Kyoto Univ. for the past 30 years. First, the ability of UV radiation to induce transformation was investigated with viral DNA. The formation of thymine-thymine dimer was found harmful to organisms and such dimers were removable by UV-radiation at a low frequency. The mutability was determined in three different E.coli strains with mutator gene, mutT, mutS or mutL. The ability to excise 8-oxoguanin developed in primer DNA was deficient in mutT and miss-pairing left after DNA replication could not be recovered in mutL and mutS strains. Further, DNA repairing mechanism was investigated in other microorganisms; single-strand cleavage caused by exposure to BNCB radiation (boron-neutron-captured beam) could not be repaired in E. coli. Whereas for Deinococcus radiodurans, of which survival rate was not decreased by ...

Energy Technology Data Exchange (ETDEWEB)

The purpose is to define sustainable economic development in the context of nonrenewable resources and to examine the changing nature of reclamation over time. Sustainable development is development that ensures the present utilization of resources and the environment does not damage prospects for their use by future generations. Polls show that the public is demanding higher environmental standards. One mechanism for achieving sustainable economic development for the nonrenewable resource sector is through reclamation. The Alberta government`s approach to reclamation is reviewed to show how reclamation and sustainable government are linked together. The history of reclamation legislation in Alberta is summarized. 10 refs.

International Nuclear Information System (INIS)

The post (neutron) -irradiation high-temperature tensile and creep-rupture properties, deformation and fracture characteristics of austenitic alloys, particularly solution annealed Type 316 steel, are surveyed and correlated with the damage structures developed as a function of irradiation temperature (and dose). The mechanisms proposed to explain the irradiation-induced changes in properties and behaviour are summarised. The factors responsible for the observed differences in the post-irradiation and 'in-reactor' creep-rupture properties and behaviour of an austenitic steel are discussed in terms of the helium gas and stress driven growth of small intergranular bubbles and the atom plating associated with their growth and coalescence. (author).

International Nuclear Information System (INIS)

The sensitivity of the primary circuit material was examined at the Mochovce and Dukovany NPPs. No significant sensitivity of the base material or the weld metal to the initiation of corrosion cracking was observed. Thermal aging was found to accelerate significantly the corrosion fatigue kinetics in the material of the heat affected zone. The threshold values of the double amplitudes of the stress intensity factor were below 8 MPa/m"2 for the materials examined, with a cycle asymmetry coefficient of 0.65. The tests revealed no appreciable sensitivity to general corrosion, pitting, or intergranular corrosion. (J.B.). 7 tabs., 26 figs., 11 refs.

Energy Technology Data Exchange (ETDEWEB)

Significantly improved immunity to hot-hole damage of the SiO[sub 2]/Si structure is achieved by a shallow fluorine implantation into the poly-Si gate of MOS capacitors followed by a drive-in process. Compared to the nonfluorinated control, the fluorinated samples exhibit a dramatic reduction of both hole trapping probability and interface-trap generation under avalanche hole injection conditions. The degree of such an improvement increases monotonically as a function of the F implantation dose (up to 10[sup 16]/cm[sup 2]). Significant decrease of the hole detrapping rate is also observed in fluorinated samples. Possible mechanisms are discussed.

Energy Technology Data Exchange (ETDEWEB)

Damage survey of protective coats of modern gas turbine blade shows that most damages are not due to classic wear mechanisms such as oxydation or high-temperature corrosion but caused by foreign bodies, poor coating during manufacturing, or operation-caused cracks. Mere visual inspection of cracks is often not sufficient to tell whether cracks are superficial or whether they have already progressed into the base material. Non-destructive methods such as ultrasonic inspection or eddy-current testing are helpful tools but there is not yet a fully matured testing concept at hand. Metallographical tests can give important information about crack mechanisms and thermal, chemical and mechanical stresses.(orig.) [German] Die Schadenerfahrung mit Schutzschichten moderner Gasturbinenschaufeln zeigt, dass die meisten Schaeden nicht auf die klassischen Verbrauchsmechanismen wie Oxydation und ...

International Nuclear Information System (INIS)

An attempt has been made to grow L-tartaric acid nicotinamide (LTN); a complex of tartaric acid, by employing a modified unidirectional method. The crystalline structure and quality are investigated by single crystal XRD and rocking curve studies. The linear and nonlinear optical properties are studied by UV-vis-NIR spectral analysis, SHG test, phase matching and laser induced damage threshold measurement. For comparison, parallel growth of the crystal was carried out by conventional method and the properties of the LTN samples grown by the conventional and unidirectional methods are investigated. The mechanical, photoconductivity and dielectric behavior of LTN crystals are also investigated.

British Library Electronic Table of Contents (United Kingdom)

A better understanding of the immune processes in the pathogenesis and progression of prostate cancer (CaP) may point the way towards improved treatment modalities. The challenge is to amplify immune responses to combat tumour escape mechanisms. Infection and inflammation may have a role in prostate carcinogenesis, including the newly discovered xenotropic murine leukaemia virus (XMRV). These inflammatory states damage defence mechanisms and induce a high proliferative state favouring further mutation and impaired immune surveillance. With this knowledge we are able to explore the use of immunotherapy to rejuvenate the immune system in combating CaP. Recently Sipuleucel-T, an immunotherapeutic agent for metastatic androgen independent CaP, has resulted in improved survival and might be the...

International Nuclear Information System (INIS)

The main objectives of research in the field of health effects at the Belgian Nuclear Research Centre SCK-CEN are: (1) to study cancer mortality and morbidity in nuclear workers in Belgium; (2) to document the feasibility of retrospective cohort studies in Belgium; (3) to participate in the IARC study; (4) to elucidate the mechanisms of the effects of ionizing radiation on the mammalian embryo during the early phases of its development; (5) to assess the genetic risks of material exposure to ionizing radiation; (6) to elucidate the cellular mechanisms leading to brain damage after prenatal irradiation; (7) to advise authorities and to provide the general population with adequate information concerning the health risk arising from radiation exposure. Progress and major achievements in these topical areas for 1997 are reported.

Energy Technology Data Exchange (ETDEWEB)

A strong effort is currently being devoted to the investigation of defects and diffusion phenomena in silicon. This effort is not only driven by the stringent technological requirements for the processing of integrated circuits of increased complexity and miniaturization, but also by the lack of fundamental understanding of many of the critical parameters and mechanisms involved. Experimental and theoretical investigations are needed to identify the properties of the defects, the mechanisms of impurity diffusion and the strength of impurity-defect, defect-defect, and impurity-impurity interactions. This volume provides a unique and interdisciplinary forum for the discussion of experimental, theoretical and applied aspects of defects and diffusion phenomena in silicon. Topics include: defect properties and diffusion phenomena in silicon; experimental and theoretical assessments of defect properties; transient-enhanced diffusion and dopant ...

Energy Technology Data Exchange (ETDEWEB)

One of the main factors that require special attention in a pipeline construction is the cold bending process, once depending on the region that the line will be installed the number of bends may achieve 75%, as it was observed in some areas during Campinas-Rio pipeline construction. A study was carried out to evaluate the X80 cold bending operational parameters in order to make viable the use of high strength pipes in the construction of onshore pipelines. For this analysis three pipes of 34 inches x 0.750 inches had been cold bended, the operation was carried out using a hydraulic equipment with punches applications along the pipe, recording the correspondent angles related to the elastic and plastic deformations in order to assess the material spring-back. After the bending process, samples of the weld, extrados and intrados were subjected to mechanical and metallographic tests, as well as performed dimensional inspection of the pipes. It was possible to obtain ...

CERN Document Server

The effect of pair-binding energy variations on the denaturation of double stranded DNAs is investigated. Using a two-parameter renormalization group (RG) analysis and extensive transfer matrix calculations, we find a random quenched-in variations to be marginally irrelevant, indicating that the system is self-averaging at the transition. The effect of a recently-proposed variable backbone stiffness is also investigated. Although irrelevant in the RG sense, it dramatically amplifies the randomness, leading to the appearance of ``multi-step melting'' for realistic sequences. These results are relevant to the adsorption of random heteropolymers and the wetting of disordered substrates.

International Nuclear Information System (INIS)

Implanted B and P dopants in Si exhibit transient enhanced diffusion (TED) during annealing which arises from the excess interstitials generated by the implant. In order to study the mechanisms of TED, transmission electron microscopy measurements of implantation damage were combined with B diffusion experiments using doping marker structures grown by molecular-beam epitaxy (MBE). Damage from nonamorphizing Si implants at doses ranging from 5x10"1"2 to 1x10"1"4/cm"2 evolves into a distribution of #left brace#311#right brace# interstitial agglomerates during the initial annealing stages at 670 endash 815 degree C. The excess interstitial concentration contained in these defects roughly equals the implanted ion dose, an observation that is corroborated by atomistic Monte Carlo simulations of implantation and annealing processes. The injection of interstitials from the damage region involves the ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Implanted B and P dopants in Si exhibit transient enhanced diffusion (TED) during initial annealing which arises from the excess interstitials generated by the implant. In order to study the mechanisms of TED, the authors have used B doping marker layers in Si to probe the injection of interstitials from near-surface, non-amorphizing Si implants during annealing. The in-diffusion of interstitials is limited by trapping at impurities and has an activation energy of {approximately}3.5 eV. Substitutional C is the dominant trapping center with a binding energy of 2--2.5 eV. The high interstitial supersaturation adjacent to the implant damage drives substitutional B into metastable clusters at concentrations below the B solid solubility limit. Transmission electron microscopy shows that the interstitials driving TED are emitted from {l_brace}311{r_brace} defect clusters in the damage region at a rate which also exhibits an ...

Energy Technology Data Exchange (ETDEWEB)

Multilayer mirrors for the extreme ultraviolet (EUV) are keyelements for numerous applications of coherent EUV sources such as newtabletop lasers and free-electron lasers. However the field ofapplications is limited by the radiation and thermal stability of themultilayers. Taking into account the growing power of EUV sources thestability of the optics becomes crucial. To overcome this problem it isnecessary to study the degradation of multilayers and try to increasetheir temporal and thermal stability. In this paper we report the resultsof detailed study of structural changes in Sc/Simultilayers when exposedto intense EUV laser pulses. Various types of surface damage such asmelting, boiling, shockwave creation and ablation were observed asirradiation fluencies increase. Cross-sectional TEM study revealed thatthe layer structure was completely destroyed in the upper part ofmultilayer, but still survived below. The layers adjacent tothe substrateremained intact even ...

Energy Technology Data Exchange (ETDEWEB)

Swift heavy ion-solid interaction leads in volume to track creation and on the surface to the ejection of particles into the vacuum. To learn more about initial mechanisms of track formation, we are focused on the sputtering of uranium dioxide by fast heavy ions. This present study is exclusively devoted to the influence of the electronic stopping power on the emission of neutral particles and especially on their angular distribution. These measurements are completed by those of the ions emitted from UO{sub 2} targets bombarded with swift heavy ions. The whole experimental results give access to: i) the nature of the sputtered particles; ii) the charge state of the emitted particles; iii) the direction of ejection of the sputtered particles ; iv) the sputtering yields deduced from the angular distributions. These results are compared to the prediction of the sputtering models proposed in the literature and it seems that the supersonic gas flow model is well suited ...

Energy Technology Data Exchange (ETDEWEB)

Chicken embryos were x-irradiated in ovo with 5-30 cGy (=priming dose) at the 13th-15th day of development. After 3-48 h, brain- and liver-cell suspensions were x-irradiated in vitro with (challenge) doses of 4-32 Gy. Significantly less radiation damage was observed when the radiation response was measured by scheduled DNA synthesis, nucleoid sedimentation and viscosity of alkaline cell lysates 12-36 h after the priming exposure. In vivo, pre-irradiation with 10 cGy enhanced regeneration as evidenced by the DNA content of chicken embryo brain and liver 24 h following a challenge dose of 4 Gy. From nucleoid sedimentation analyses in brain and liver cells immediately after irradiation with 16 Gy and after a 30-min repair period in the presence of aphidicolin, dideoxythymidine and 3-aminobenzamide or in the absence of these DNA repair inhibitors, it is concluded that a reduction of the initial radiation damage is the dominant ...

Science.gov (United States)

The knowledge of wound ballistics and of wounding mechanisms is mandatory for the radiologist to interpret the CT findings of gunshot wounds. The severity of a bullet wound depends on the characteristics of the tissue it goes through, i.e., tissue elasticity, density, thickness of the wounded body part, the type of tissue, its specific gravity, internal cohesiveness and anatomical relationships, as well as on missile characteristics, i.e., mass, shape, fragmentation and deformation. Bullet velocity is certainly a major factor in wounding, but it is only one factor. Two major wounding mechanisms exist the crushing of the bullet-struck tissue (forming the permanent cavity) and radial stretching (forming a temporary cavity). Bullet "yaw" is defined as the angle between the long axis of the bullet and its flight path. The yaw is directly proportional to tissue crushing and stretching: the wider the yaw, the most severe tissue crushing and ...

Energy Technology Data Exchange (ETDEWEB)

The dominant fracture parameters used in fracture mechanics analyses of pipelines are related to the asymptotic crack-tip stress and strain fields at the crack tip. This paper reviewed new developments in constraint-sensitive fracture mechanics for the assessment of pipeline girth weld integrity. Constraint theories and experimental studies were evaluated. Constraint models included brittle fracture models and ductile fracture models. Constraint models for brittle fracture are based on weakest link statistics and Weibull distribution. Specifically designed experimental tests are often necessary to derive the damage parameters of ductile fracture models. Experimental test data must then be calibrated with finite element analyses (FEA) to ensure that the correct damage parameters are chosen. The effects of specimen geometry and loading condition are characterized by the T stress, while Q stress is the ...

International Nuclear Information System (INIS)

Titanium base 'alpha'-alloys (Pt-7M, RK-20 and Ti-5Al-2Zr-1.5V) are considered for their behaviour under neutron irradiation. The role of alloying elements in radiation hardening is discussed depending of neutron fluence and irradiation temperature. For PK-20 alloy three stages of change in mechanical properties are revealed which are following: incubation period and weak hardening, intense radiation hardening, radiation hardening attenuation. Irradiation temperature rise results in an increase of incubation period and threshold neutron fluence. A special attention is paid to hydrogen absorption in #alpha#-titanium alloys under irradiation. It is concluded that titanium base 'alpha'-alloys are serviceable as structural materials in nuclear plants with allowance made for peculiar features of their radiation behaviour. 4 refs.; 7 figs.; 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The author explains current developments in high voltage cable technology and subsequently describes problems inherent in its application, from the users viewpoint, in municipal electricity supply. The planning of a high voltage cable network and the selection of a specific type of cable are not only dependent on the typical properties of various cables but to a major degree also on the feasible laying technique, the power transmitted, the costs, the stellation treatment of the high voltage network, the acceptance requirement, the inductive influence from telecommunication cable, thermal influences from the environment, eventual safeguards from mechanical and chemical damage to the network, frequency of failure and surveillance and breakdown location. In conclusion, the author portrays potential developments in the fields of high and maximum voltage cable from the perspectives of today.

International Nuclear Information System (INIS)

The stages of processes leading to radiation damage are studied, as well as, the direct and indirect mechanics of its production. The radiation effects on nucleic acid and protein macro moleculas are treated. The physical and chemical factors that modify radiosensibility are analysed, in particular the oxygen effects, the sensibilization by analogues of nitrogen bases, post-effects, chemical protection and inherent cell factors. Consideration is given to restoration processes by excision of injured fragments, the bloching of the excision restoration processes, the restoration of lesions caused by ionizing radiations and to the restoration by genetic recombination. Referring to somatic effects of radiation, the early ones and the acute syndrome of radiation are discussed. The difference of radiosensibility observed in mammalian cells and main observable alterations in tissues and organs are commented. Referring to delayed radiation effects, ...

Energy Technology Data Exchange (ETDEWEB)

The needs for more reasonable estimations for rare and extremely rare initiating events (IEs) have been reported in US peer review results. The American Society of Mechanical Engineers (ASME) PRA standard also proposes guidelines and requirements about the issues. Recently, US NRC addressed problems and the conservative assumptions on loss-of-coolant accident (LOCA) analysis and attempted to establish more rigorous methodology for estimating the frequencies depending on break size. The results of peer reviews for KHNP reference plants also represented that the data used in estimating IEs were outdated and the methodology also needed to be improved. In this paper, for more appropriate estimation of rare and extremely rare initiating events (IEs), e.g., LOCAs and steam generator tube ruptures (SGTRs), a new approach considering expert elicitation process is presented and corresponding core damage frequency (CDF) is calculated

Science.gov (United States)

Candoxin (PDB #1JGK), a three-finger neurotoxin from Bungarus candidus venom, inhibits post-synaptic neuromuscular and neuronal alpha7nACh-receptors, and induces delayed cell-death throughout the glial population. When applied to cultured human glial cell lines, candoxin (CDX) induced cell death in a concentration (EC(50) approximately 1muM) and time dependent manner. Results of TUNEL-histochemistry further confirm CDX-induced brain (hippocampus, frontal cortex, and temporal regions) damage when administered intracerebroventricularly (i.c.v) in adult mice. In this study, we explored differential gene expression profiles following exposure of human glial (Hs 683) cell lines to CDX at various time intervals using Affymetrix-GeneChips. By means of MAS and GeneSpring analyses, 105 genes whose expression was significantly (P<0.01) altered by at least 3-fold were selected. Results of the genome analysis reveal that the potential role of CDX at molecular level involves ...

Energy Technology Data Exchange (ETDEWEB)

The process of implementing a damage detection strategy for aerospace, civil and mechanical engineering infrastructure is referred to as structural health monitoring (SHM). Here damage is defined as changes to the material and/or geometric properties of these systems, including changes to the boundary conditions and system connectivity, which adversely affect the system's current or future performance. Our approach is to address the SHM problem in the context of a statistical pattern recognition paradigm (Farrar, Nix and Doebling, 2001). In this paradigm, the process can be broken down into four parts: (1) Operational Evaluation, (2) Data Acquisition, (3) Feature Extraction, and (4) Statistical Model Development for Feature Discrimination. When one attempts to apply this paradigm to data from 'real-world' structures, it quickly becomes apparent that data cleansing, normalization, fusion and ...

CERN Document Server

In the CLIC main linac it is very important to minimise the trajectory excursion and consequently the emittance dilution in order to obtain the required luminosity. Several algorithms have been proposed and lately the ballistic method has proved to be very effective. The trajectory method described in this Note retains the main advantages of the latter while adding some interesting features. It is based on the separation of the unknown variables like the quadrupole misalignments, the offset and slope of the injection straight line and the misalignments of the beam position monitors (BPM). This is achieved by referring the trajectory relatively to the injection line and not to the average pre-alignment line and by using two trajectories each corresponding to slightly different quadrupole strengths. A reference straight line is then derived onto which the beam is bent by a kick obtained by moving the first quadrupole. The other quadrupoles are then aligned on that line. The quality of ...

International Nuclear Information System (INIS)

Textured silicon nitride (Si_3N_4) has been intensively studied over the past 15 years because of its use for achieving its superthermal and mechanical properties. In this review we present the fundamental aspects of the processing and anisotropic properties of textured Si_3N_4, with emphasis on the anisotropic and abnormal grain growth of #beta#-Si_3N_4, texture structure and texture analysis, processing methods and anisotropic properties. On the basis of the texturing mechanisms, the processing methods described in this article have been classified into two types: hot-working (HW) and templated grain growth (TGG). The HW method includes the hot-pressing, hot-forging and sinter-forging techniques, and the TGG method includes the cold-pressing, extrusion, tape-casting and strong magnetic field alignment techniques for #beta#-Si_3N_4 seed crystals. Each processing technique is thoroughly discussed in terms of theoretical models and experimental ...

British Library Electronic Table of Contents (United Kingdom)

High surface ozone concentration is increasingly being recognized as a factor that negatively affects crop yields in Asia. However, little progress has been made in developing ozone-tolerant genotypes of rice-Asias major staple crop. This study aimed to identify possible tolerance mechanisms by characterizing two quantitative trait loci (QTLs) that were previously shown to influence visible leaf symptoms under ozone exposure (120 nl l-1, 7 h d-1, 13 d). Two chromosome segment substitution lines (SL15 and SL41) that carried introgressions of the QTLs OzT3 and OzT9, respectively, were exposed to ozone at 120 nl l-1 along with their parent Nipponbare. In accordance with the expected QTL effect, SL15 showed stronger visible symptoms of ozone damage than Nipponbare, whereas SL41 had fewer sympt...

Science.gov (United States)

U3Si2 Al fuel plate is one of the dispersion fuel structure materials recently developed and widely used in research reactors. The mechanical properties of this structural material, especially the fatigue performance, are strongly dependent on its fabrication process. To investigate the effects of these processing technologies, the fatigue tests for the different specimens were carried out. The S N curves indicate that the fabrication processing technologies of U3Si2 fuel plate, such as the addition of U3Si2 particles into aluminum powder to form the fuel meat, holding and rolling the processes of meat and cladding of 6061-Al alloy, plays an important role in improving the mechanical properties and fatigue performance of this fuel plate. In addition, some factors that influence the crack initiation and propagation are summarized based on the fatigue images that are in situ observations with SEM. The critical criterion for fatigue ...

International Nuclear Information System (INIS)

Acetylcholine and other neurotransmitters play unique trophic roles in brain development. Accordingly, drugs and environmental toxicants that promote or interfere with neurotransmitter function evoke neurodevelopmental abnormalities by disrupting the timing or intensity of neurotrophic actions. The current review discusses three exposure scenarios involving acetylcholine systems: nicotine from maternal smoking during pregnancy, exposure to environmental tobacco smoke (ETS), and exposure to the organophosphate insecticide, chlorpyrifos (CPF). All three have long-term, adverse effects on specific processes involved in brain cell replication and differentiation, synaptic development and function, and ultimately behavioral performance. Many of these effects can be traced to the sequence of cellular events surrounding the trophic role of acetylcholine acting on its specific cellular receptors and associated signaling cascades. However, for chlorpyrifos, additional noncholinergic ...

Energy Technology Data Exchange (ETDEWEB)

Urban type R D (research and development) facilities have research institute functions which are not desirable to coexist in a city as compared with suburban R D facilities. Therefore careful consideration must be given to environmental protection. KSP is the first large scale urban type R D facility in Japan. The planning and construction have been made with the theme of realization of flexibility in architecture and mechanical planning as well as realization of environmental integrity. To achieve the target so-called technical slit is built at the center of the building to provide a void space for securing natural ventilation. It is effective for provision of internal mechanical spaces without spoiling urban View air exhaust from laboratories natural ventilation for underground parking lots and decrease of damage by strong wind on the ground level. Standards are established and organization is formed for environmental ...

Energy Technology Data Exchange (ETDEWEB)

Heterochromatin constitutes a significant portion of the genome in higher eukaryotes; approximately 30% in Drosophila and human. Heterochromatin contains a high repeat DNA content and a low density of protein-encoding genes. In contrast, euchromatin is composed mostly of unique sequences and contains the majority of single-copy genes. Genetic and cytological studies demonstrated that heterochromatin exhibits regulatory roles in chromosome organization, centromere function and telomere protection. As an epigenetically regulated structure, heterochromatin formation is not defined by any DNA sequence consensus. Heterochromatin is characterized by its association with nucleosomes containing methylated-lysine 9 of histone H3 (H3K9me), heterochromatin protein 1 (HP1) that binds H3K9me, and Su(var)3-9, which methylates H3K9 and binds HP1. Heterochromatin formation and functions are influenced by HP1, Su(var)3-9, and the RNA interference (RNAi) pathway. My thesis project investigates how ...

Energy Technology Data Exchange (ETDEWEB)

Spice extracts under the form of essential oils were tested for their efficiency to increase the relative radiosensitivity of Listeria monocytogenes and Escherichia coli O157H7 in culture media. The two pathogens were treated by gamma-irradiation alone or in combination with oregano essential oil to evaluate their mechanism of action. The membrane murein composition, and the intracellular and extracellular concentration of ATP was determined. The bacterial strains were treated with two irradiation doses: 1.2 kGy to induce cell damage and 3.5 kGy to cause cell death for L. monocytogenes. A dose of 0.4 kGy to induce cell damages, 1.1 kGy to obtain viable but nonculturable (VBNC) state and 1.3 kGy to obtain a lethal dose was also applied on E. coli O157H7. Oregano essential oil was used at 0.020% and 0.025% (w/v), which is the minimum inhibitory concentration (MIC) for L. monocytogenes. For E. coli O157H7, a concentration of ...

UK PubMed Central (United Kingdom)

DNA damage is a threat to genomic integrity in all living organisms. Plants and green algae are particularly susceptible to DNA damage especially that caused by UV light, due to their light dependency...Full Text Available

Science.gov (United States)

... The revised work plan emphasized the research priorities of preharvest rodent damage to rice, the importance of postharvest food losses to rodents ...

Energy Technology Data Exchange (ETDEWEB)

Radiation Damage Calculations for the FUBR and BEATRIX Irradiations of Lithium Compunds in EBR-II and FFTF

Energy Technology Data Exchange (ETDEWEB)

Short communication

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The author furnishes a review of incidents of major damage to high-output steam turbines. At the same time, he thereby underlines the call for an improvement in the exchange of experience on such damage and its causes at international level. Only the careful observance of past damage experience - including that of foreign manufacturers and operators - complete and modern monitoring equipment and the painstaking evaluation of all data furnished by such equipment can keep the risk of new technical development within economically tolerable limits. (orig.).

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Exposure of cells to light of less than 320 nanometers wavelengths may lead to lethal lesions and perhaps carcinogenesis. Many organisms have evolved mechanisms to repair U.V. light-induced damage. Organisms such as deep-sea bacteria are presumably never exposed to U.V. light and perhaps occasionally to visible from bioluminescence. Thus, the repair of U.V. damage in deep-sea bacterial DNA might be inefficient and repair by photoreactivation unlikely. The bacteria utilized in this investigation are temperature sensitive and barophilic. Four deep-sea isolates were chosen for this study: PE-36 from 3584 m, CNPT-3 from 5782 m, HS-34 from 5682 m, and MT-41 from 10,476 m, all are from the North Pacific ocean. The deep-sea extends from 1100 m to depths greater than 7000 m. It is a region of relatively uniform conditions. The temperature ranges from 5 to -1"0C. There is no solar light in the deep-sea. Deep-sea bacteria are ...

Energy Technology Data Exchange (ETDEWEB)

We have investigated tailoring damage effects of explosive devices by addition of unconventional materials, specifically combustible metals. Initial small-scale as well as full-scale testing has been performed. The explosives functioned to disperse and ignite these materials. Incendiary, enhanced-blast, and fragment-damage effect have been identified. These types of effects can be used to extend the damage done to hardened facilities. In other cases it is desirable to disable the target with minimal collateral damage. Use of unconventional materials allows the capability to tailor the damage and effects of explosive devices for these and other applications. Current work includes testing of an incendiary warhead for a penetrator.

International Nuclear Information System (INIS)

A statistical evaluation of rotor blade damage in axial steam turbines affords an insight into the extent of the repair costs incurred and reveals the types of defects and shortcomings which cause such damage. The great amount of rotor blade damage discovered during control inspections will surprise even many turbine experts. The statistical evaluation is followed by a review of the more frequent causes of damage and their characteristic features, illustrated on the basis of practical examples. This contribution is intended as an aid to both the manufacturers and operators of steam turbines in preventing the oft almost classic types of faults which constantly recur. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Machine condition monitoring (MCM) has the capability to predict equipment maintenance needs which can reduce forced down-time and facilitate the avoidance of catastrophic failures and the consequential secondary damage. It can be used to allow confident deferral of routine maintenance, and improve equipment performance, availability, reliability and safety. In order to capitalize on the potential benefits of MCM directed toward power transformers two types of vibration tests were conducted on transformers owned and operated by Cargill Inc. and IES Utilities at the Bridgeport corn plant in Eddyville, Iowa. These tests involved collecting vibration signals from the transformer tank walls during transformer energization at no-load and during steady state operation at various loads. These vibration signals were then used to detect deterioration of internal mechanical integrity. Both types of tests conducted on the transformers at the Eddyville ...

Energy Technology Data Exchange (ETDEWEB)

During rolling contact fatigue of the inner rings of ball bearings three stages of material response can be distinguished, in terms of the volume that is plastically deformed upon overrolling. After a first stage of material strengthening during which a decrease occurs for the volume that is deformed plastically, an effectively stationary, second stage is entered which is eventually succeeded by a third stage exhibiting a pronounced increase of the volume that is deformed plastically upon overrolling, which leads to failure. It is suggested that carbon diffusion induced by local temperature peaks occurring at the moment of overrolling is the key mechanism leading to fatigue damage. The amount of decomposed retained austenite is a useful, practical parameter to assess fatigue life. It is shown that published ideas about the role of certain components of residual stress in enhancing fatigue life are not correct and that the so-called ...

Energy Technology Data Exchange (ETDEWEB)

Ice jamming, known to cause high water levels at even moderate river flows, is described as both the main and least understood source of ice-related bridge damages. This paper describes a joint study by the New Brunswick Department of Transportation, the Department of the Environment, local governments, and the National Water Research Institute, designed to address problems associated with the interaction of ice jams and bridges. The study consists of collecting information at each of four sites in New Brunswick including: historical data on ice jam locations, causes, and water levels; channel bathymetry, width and slope within each study centred at the respective bridge; and documentation of ice conditions throughout the ice season, including measurement of ice cover thickness, observation of breakup mechanisms, times, causes, characteristics and possible impacts of ice jam release. Data analysis will include determination of high stages due ...

International Nuclear Information System (INIS)

Total-dose irradiation seriously damages MOS devices and their circuit performance. Threshold voltage shifts, transconductance degradation and increase in off-state leakage current are generally observed for irradiated devices. These instabilities are essentially due to positive and/or negative charge trapping in SiO_2 and interface trap generation at the SiO_2/Si interface. Radiation hardening of CMOS VLSIs is to eliminate these trapping effects, and for this purpose, special considerations for fabrication processes and layout design are necessary. In this paper, basic mechanisms for radiation-induced charge trapping and related effects on MOS devices are reviewed. Also discussed are radiation-hardening technologies from both fabrication-process and layout-design viewpoints. Using these technologies, 1 #mu#m radiation-hard CMOS gate arrays have been successfully developed. Experimental data taken for 2k-gate test chips indicate that radiation ...

Energy Technology Data Exchange (ETDEWEB)

The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for ...

International Nuclear Information System (INIS)

We investigate some aspects of the radiation damage mechanisms in biomolecules, focusing on the modelling of resonant fragmentation caused by the attachment of low-energy electrons (LEEs) initially ejected by biological tissues when exposed to ionizing radiation. Scattering equations are formulated within a symmetry-adapted, single-center expansion of both continuum and bound electrons, and the interaction forces are obtained from a combination of ab initio calculations and a nonempirical model of exchange and correlation effects developed in our group. We present total elastic scattering cross-sections and resonance features obtained for the equilibrium geometries of glycine, alanine, proline and valine. Our results at those geometries of the target molecules are briefly shown to qualitatively explain some of the fragmentation patterns obtained in experiments. We further carry out a one-dimensional (1D) modeling for the dynamics of ...

International Nuclear Information System (INIS)

Radon has been recognized by various international health organizations as a major lung carcinogen. The onset of cellular carcinogenesis involves DNA damage to bronchi epithelial cells by particles emitted by radon progeny. Radon diffusion is an important release mechanism for radon that is produced inside a building material. The physical parameter that characterizes this process is the radon diffusion Coefficient D(m-2 s-l). The diffusion constant and Diffusion length has been measured as 2.15xl0- 6 m-2s-1, 1.01m for soil, 1.65x10-6m-2s-1, 0.89m for sand and 0.21x 10-6m-2s-1, 0.31m for crush aggregate saudi building materials respectively. The values are found to be minimum for crush aggregates, which shows that crush aggregate is least permeable to radon flow as compared with the other building materials studied. (author)

Energy Technology Data Exchange (ETDEWEB)

The plastic displacements around Knoop indentations made in hard titanium/aluminum multilayered films on soft aluminum alloy substrates have been studied. Indentations were cross-sectioned and imaged using the focused-ion-beam (FIB) milling and high-resolution scanning electron microscopy (SEM), respectively. The FIB milling method has the advantage of removing material in a localized region without producing mechanical damage to the specimen. The micrographs of the cross-sectioned indentations indicate that most of the plastic deformation around the indentation is dominated by the soft aluminum substrate. There is a very small change in the multilayered film thickness around the indentation{emdash}less than 10{percent}. The plastic deformation of the thin film resembles a membrane being deflected by a localized pressure gradient across the membrane. Stress-induced voids are also observed in the multilayered film, especially in the area around ...

Science.gov (United States)

Ballistics involves the study of the scientific properties of projectiles, their behavior and their terminal effects on biological tissues and other materials. Wound ballistics deals with the analysis of injuries caused by projectiles and the behavior of projectiles within human or other biological tissues. The nineteenth century witnessed the development of both of these areas with Kocher's hydrodynamic theory and the understanding of the significance of bullet deformation in causing tissue injury. The degree of traumatic disruption of tissues and organs was also related to direct energy transfer from projectiles. While subsequent research has concentrated on elucidating further mechanisms of injury, the exact cause of remote tissue damage from high energy projectiles is still the subject of ongoing research. Much of the contemporary literature regarding wound ballistics concentrates on the forensic aspects and their application for legal ...

Energy Technology Data Exchange (ETDEWEB)

High concentrations of self-interstitials are trapped by dopant atoms during ion implantation into Si. For group V dopants, these complexes are sufficiently stable to survive solid-phase-epitaxial (SPE) growth but break up on subsequent thermal processing and cause a transient-enhanced diffusion. Dopant diffusion coefficients are enhanced by up to five orders of magnitude over tracer values and are characterized by an activation energy of approximately one half of the tracer values. In the case of group III dopants, any complexes formed during implantation do not survive SPE growth but a second source of self-interstitials becomes significant and leads to similar transient effects. This is the damaged layer underlying the original amorphous/crystalline interface. These observations provide direct evidence for long-range self-interstitial migration in Si, and we believe these are the first observations of the interstitialcy diffusion mechanism ...

International Nuclear Information System (INIS)

Reference is made to Cheng and Leblond (Amer. J. Anat.; 141:537 (1974)) who used tritiated thymidine to kill cells synthesising DNA in the crypts of the small intestine. Amongst their findings was that very low doses caused measurable cell killing and that the killing was not random throughout the crypt but occurred selectively at the crypt base where stem cells are presumably located. It is here reported that the presence of hypersensitive cells at the base of the crypts can be demonstrated after whole-body X- or gamma-irradiation, and the time sequence for the production and loss of the killed cells is described together with their dose-response relationship. The studies were conducted on mice. The data were expressed as surviving rather than killed cells, and it was established that the crypt are amongst the most sensitive of mammalian cells. The mechanism by which these sensitive cells are killed is not known, but DNA damage can be ...

Energy Technology Data Exchange (ETDEWEB)

Tensile specimens of the normalized and tempered fully martensitic steel DIN 1.4914 were helium implanted up to 340 appm within the temperature range 300-720/sup 0/C using a 104 MeV alpha particle beam. The high He/damage ratio of 1850 appm He/dpa allowed to determine the effect of helium on material properties. After irradiation tensile strength and ductility were investigated mainly at test temperatures equal to the irradiation temperatures. While short time irradiations with helium contents up to 100 appm have shown no visible effect on the tensile behaviour at all temperatures investigated, long time irradiations reduced the material strength at irradiation temperatures above about 440/sup 0/C. This irradiation induced softening obscured the predicted minor hardening effect of the observed He-bubbles completely and increases with irradiation time and temperature. The fracture mode of helium-implanted and control specimens is found to remain always ductile and ...

Energy Technology Data Exchange (ETDEWEB)

The phenomena and effects of airblast, ground shock, thermal radiation, cratering and ejecta, and debris cloud and deposition from the eruption of Mt. St. Helens were compared to those that would result from a nuclear explosion to determine if phenomena or effects were analogous and thus might provide useful data for military nuclear weapon effects studies. It is concluded that the phenomena are not analogous. In particular, airblast destruction was caused by clouds of ash driven by subsonic winds, rather than by a supersonic shock wave that would be the damage mechanism of a nuclear explosion. Because of the lack of analogy between the eruption and nuclear explosion phenomena, it appears questionable that any of the effects are analogous; therefore, it is unlikely that anything more of military interest can be gained from studying the effects of the eruption. However, key contacts for further information on the eruption and the associated ...

Energy Technology Data Exchange (ETDEWEB)

This report is a survey of the English language literature of radiation biology between 1947 and 1987, for the purpose of compiling a literature base on the effects of radiation on animals, which have yielded results that can expand our knowledge about similar radiation effects on human beings. Articles were sought that reported exposure of adult mammals to external sources of ionizing radiation, having endpoints that included effects on the brain, the spinal cord, and behavior of the gastrointestinal, endocrine, and cardiovascular systems and the hematopoietic and immune systems. Effects of interest were those that occurred within the first 12 months after exposure. The survey does not include articles reporting chronic or long term delayed effects of radiation unless they provided insight into mechanisms of morphological and/or functional derangement. Information presented in the report is divided into subtopics (i.e., Brain-Morphological Changes). The brief ...

Energy Technology Data Exchange (ETDEWEB)

Wind power is an increasingly significant renewable energy resource, producing no environmentally damaging CO2 emissions. The efficient production of electricity by wind turbines relies on aerodynamics. Aerodynamics of Wind Turbines provides the fundamental solutions to efficient wind turbine design. Following a historical introduction, Part 1 of Aerodynamics of Wind Turbines is concerned with basic rotor aerodynamics, while Part 2 deals with structural aspects of the wind turbine and calculation of the loads on it. Topics covered include increasing mass flow through the turbine, performance at low and high wind speeds, assessment of the extreme conditions under which the turbine will perform and the theory for calculating the lifetime of the turbine. The classical Blade Element Momentum method is also covered, as are eigenmodes and the dynamic behaviour of a turbine. Aerodynamics of Wind Turbines is an essential reference for both engineering students and others ...

International Nuclear Information System (INIS)

This paper reports on the superiority of zeolites over amorphous solids which is well documented for solid acid catalysts of industrial use. Crystalline supports, likewise, open attractive perspectives for catalysis by metals, alloys, and ligated metal clusters. Size and location of clusters can be controlled by careful design of the preparation conditions. Pore dimensions control the access of reactants to active sites and escape paths for products. Cage dimensions determine which transition states can be attained; window apertures are functional in isolating metal clusters from each other, thus preventing ther coalescence and growth. The ship-in-a-bottle method permits deisgn of fairly large active complexes entrapped in zeolite cages. Orientation of non-spherical molecules in a zeolite proe helps to direct their collision with a metal particle to the head on mode; however, isolated Pt atoms hidden in niches of the pore walls can attack passing molecules at their soft flanks. ...

Energy Technology Data Exchange (ETDEWEB)

Borohydrides such as LiBH{sub 4} have been studied as candidates for hydrogen storage because of their high hydrogen contents (18.4 wt% for LiBH{sub 4}). Limited success has been made in reducing the dehydrogenation temperature by adding reactants such as metals, metal oxides and metal halides. However, full rehydrogenation has not been realized because of multi-step decomposition processes and the stable intermediate species produced. It is suggested that adding second cation in LiBH{sub 4} may reduce the binding energy of B-H. The second cation may also provide the pathway for full rehydrogenation. In this work, several bimetallic borohydrides were synthesized using wet chemistry, high pressure reactive ball milling and sintering processes. The investigation found that the thermodynamic stability was reduced, but the full rehydrogenation is still a challenge. Although our experiments show the partial reversibility of the bimetallic borohydrides, it was not ...

International Nuclear Information System (INIS)

Inelastic scattering of 180 MeV #pi#"+ and #pi#"- from "5"2Cr shows an angular distribution for the 2_2"+ state at 2.96 MeV that differs greatly from the usual L = 2 shapes for 2"+ states. This state is perhaps the only case from pion-inelastic scattering in which standard distorted-wave impulse approximation models (including multistep and single-step responses) fail to reproduce the measured angular distribution. Furthermore, this unique excitation has been shown to have the features expected of a seniority-four proton excitation yet the pion data show charge symmetry. While coupled-channel calculations are not able to reproduce the pion data, they do agree with the shape observed for 42 MeV #alpha# particle scattering to this state, but the magnitude of the #alpha# scattering data is not consistent with a collective model and known #gamma# ray deexcitations. Scattering to the first and third 2"+ states of "5"2Cr with pions and #alpha# particles is also ...

Science.gov (United States)

In this paper a new procedure, addressed as Interpolation Damage Detecting Method (IDDM), is investigated as a possible mean for early detection and location of light damage in a structure struck by an earthquake. Damage is defined in terms of the accuracy of a spline function in interpolating the operational mode shapes (ODS) of the structure. At a certain location a decrease (statistically meaningful) of accuracy, with respect to a reference configuration, points out a localized variation of the operational shapes thus revealing the existence of damage. In this paper, the proposed method is applied to a numerical model of a multistory frame, simulating a damaged condition through a reduction of the story stiffness. Several damage scenarios have been considered and the results indicate the effectiveness of the method to assess and localize ...

Energy Technology Data Exchange (ETDEWEB)

In this experiments, we established long-termed culture methods of bone marrow stromal cells for proliferation and differentiation of stem cells. And we selected some extracts which support maximal proliferation of stromal cells with this method. We conformed the synergic effects of herval mixture extracts for stromal cell growth. The proliferation of stromal cells was increased rather by the addition of mixture extracts than by addition of single strain extract. In the previous and cooperative experiments, we selected complex extracts which increased the number of nonadherent mononuclear cells. Different cytokine expression patterns were observed stromal cells cultured in the presence or absence of mixture extracts which support differentiation of nonadherent cells. Stimulation of macrophage cell line with herval extracts with the treatments of recombinant interferon-{gamma} resulted in increased nitric oxide synthesis in a dose-dependent manners. In addition, these extracts induced ...

Scientific Electronic Library Online (English)

Abstract in english The outcome of the interaction between Biomphalaria and Schistosoma mansoni depends on the response of the host internal defence system (IDS) and the escape mechanisms of the parasite. The aim of this study was to evaluate the responsiveness of the IDS (haemocytes and soluble haemolymph factors) of resistant and susceptible Biomphalaria tenagophila lineages and Biomphalaria glabrata lineages in the presence of in vitro-transformed primary sporocysts and secondary sporocys (more) ts obtained from infected B. glabrata. To do this, we assayed the cellular adhesion index (CAI), analysed viability/mortality, used fluorescent markers to evaluate the tegumental damage and transplanted secondary sporocysts. B. tenagophila Taim was more effective against primary and secondary sporocystes than the susceptible lineage and B. glabrata. Compared with secondary sporocysts exposed to B. tenagophila, primary sporocysts showed a higher CAI, ...

International Nuclear Information System (INIS)

Plasma immersion ion implantation (PIII) is an effective materials modification and synthesis technique but has seldom been applied to ceramic materials due to the high electrical resistance that reduces the ion bombardment energy and sometimes causes serious electrical arcing in the instrument. Even in cases where PIII is applicable, the surface properties of the implanted insulating materials can be seriously affected due to the low ion energy and materials damage from electrical arcing. In order to enhance the surface and mechanical properties such as wear resistance of ceramic materials used in many industrial applications, surface modification is needed. In this work, we conduct carbon implantation into sintered #alpha#-SiC (silicon carbides that are widely used in vacuum ceramic bearings) using mesh-assisted plasma immersion ion implantation to enhance the surface properties. The use of a conducting grid is necessitated by the high ...

International Nuclear Information System (INIS)

A Task Group of the International Commission on Radiological Protection (ICRP) has finished a report Biological Effects after Prenatal Irradiation (Embryo and Fetus) which has been approved by the Main Commission and Will be Published. Some new important scientific data shall be discussed in this contribution. During the preimplantation period lethality of the mammalian embryo is the dominating radiation effect. However, in mouse strains with genetic predispositions it has been shown that also malformations can be caused. This effect is genetically determined and its mechanisms is different from the induction of malformations during major organogenesis. Radiation exposures during this prenatal period leads ato an increase of genomic instability of cells in the normal appearing fetuses. These radiation effects can be transmitted to the next generation. A renewed analysis of individuals with severe mental retardation after exposures during the 8th to 15th week post ...

Energy Technology Data Exchange (ETDEWEB)

The regular occurrence of large-scale earthquakes in Japan necessitates the use of earthquake disaster prevention systems that focus on gathering damage information on gas supply facilities immediately after an earthquake strikes and minimizing the damage. This paper discussed the development of an earthquake damage estimation system for city gas pipelines that can show damage information in real-time by using earthquake records obtained from densely deployed earthquake observation networks and the most advanced telecommunication and information technologies. The paper summarized the earthquake damage estimation system (EDES) and Toho Gas disaster prevention measures. Specific topics that were discussed included the Toho Gas supply method; earthquake countermeasures; construction of computer systems; normal and emergency operation of EDES; and verification of functions in actual ...

UK PubMed Central (United Kingdom)

Because copper catalyzes the conversion of H₂O₂ to hydroxyl radicals in vitro, it has been proposed that oxidative DNA damage may be an important component of copper toxicity....Full Text Available

UK PubMed Central (United Kingdom)

A compensatory response, viz. in vivo recovery from radiation damage to mitochondria, occurs in preclimacteric pear fruits (Pyrus communis L.) treated with ionizing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A novel acidizing process is used to increase the permeability of carbonate rock cores in the laboratory and to remove drilling fluid damage from cores and wafers. Field results show the benefits of the technology as applied both to injector and producer wells.

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

Disaster impact modeling and analysis uses huge volumes of image data that are produced immediately following a natural or an anthropogenic disaster event. Rapid damage assessment is the key to time critical decision support in disaster management to better utilize available response resources and accelerate recovery and relief efforts. But exploiting huge volumes of high resolution image data for identifying damaged areas with robust consistency in near real time is a challenging task. In this paper, we present an automated image analysis technique to identify areas of structural damage from high resolution optical satellite data using features based on image content.

Science.gov (United States)

A sandwich construction, composed of hybrid carbon-glass fiber-reinforced plastic skins and a

Science.gov (United States)

... Abstract : High temperature testing of graphite/epoxy laminates and composite sandwich panels was performed while the Shuttle was on orbit to ...

Science.gov (United States)

... storm. There was little damage to high-voltage transmission lines and communication towers in northern New England. ...

Energy Technology Data Exchange (ETDEWEB)

External radiation dose exceeded 5,000 rad in three cases, and intravaginal radiation dose was 5,000 rad in one case. Radiation damage including perforation was seen in the end of ileus in one case, in the sigmoid and rectum in two cases, and in the end of ileus, sigmoid and rectum in the last case. Satisfactory results were obtained by the removal of the ileocecum in the case of the damage in the end of the ileus. However, only colostomy was performed for the damage in the sigmoid and rectum.

Energy Technology Data Exchange (ETDEWEB)

The study examines the isothermal fatigue properties of novel ODS iron-base or nickel-base superalloys at temperatures of 850 C and 1050 C. The materials are different in grain structure and texture, so that particularly the effects of grain structures and textures can be studied. In order to also perform examinations of creep-fatigue interactions, various load cycles are applied. It is shown that the LCF-affected life of the grain structures of both alloy types is determined by the elastic modulus. The cyclic lifetimes determined by the conventional Manson-Coffin method for both alloy types exhibit differences of up to two orders of magnitude. Using the product of the total strain range and the elastic modulus, however, will yield precise life predictions. Under conditions of LCF stress only, the grain structure has no effect on the materials` service life, other than in the case of creep-fatigue, but the grain structure has a decisive influence on the damage ...

International Nuclear Information System (INIS)

EXAFS measurements are useful in determining the local atomic environment of a particular element in a solid. Since there has been some controversy about the nature of the defects produced in A-15 materials by radiation damage, such studies were carried out on some A-15 compounds, V_3Ga which was damaged by neutrons, as well as Nb_3Ge damaged by 2.5 MeV a particles. In the V_3Ga sample, site exchange disorder seems to be the most important result of the neutron damage with less than 20% of the vanadium atoms on wrong sites. However, in the Nb_3Ge samples in addition to site exchange disorder, an unusual splitting of the first near-neighbor distance between the Ge and Nb is found. This splitting, approximately 0.2 A, may explain the large Debye Waller factors observed by Burbank et al.

International Nuclear Information System (INIS)

Initial rates of resistivity-measured low-temperature damage production by fission-spectrum fast neutrons have been determined for 14 metals in the same very well characterized irradiation facility. Six of these metals were fcc, 5 bcc, and 3 hcp. Most were of quite high purity. Observed damage rates, after correction for all known extraneous resistivity-producing effects, were compared with rates predicted by the damage calculation code RECOIL, using parameters chosen from the literature. These parameters, effective displacement threshold energy, E/sub d/, and Frenkel-pair resistivity, rho/sub F/, were in many cases only best estimates, the further refinement of which may be aided by the present results. Damage efficiencies (measured/predicted rates) follow the same trends by crystal classes as seen in other fast-neutron studies.

International Nuclear Information System (INIS)

The DNA double-strand break (DSB) damage response induced by high energy charged particles on lung fibroblast cells embedded in a 3-dimensional (3-D) collagen tissue equivalents was investigated using antibodies to the DNA damage response proteins gamma-histone 2AX (#gamma#-H2AX) and phosphorylated DNA-PKcs (p-DNA-PKcs). 3-D tissue equivalents were irradiated in positions across the linear distribution of the Bragg curve profiles of 307.7 MeV/nucleon, 556.9 MeV/nucleon, or 967.0 MeV/nucleon "5"6Fe ions at a dose of 0.30 Gy. Patterns of discrete DNA damage streaks across nuclei or saturated nuclear damage were observed, with saturated nuclear damage being more predominant as samples were positioned closer to the physical Bragg peak. Quantification of the DNA damage signal intensities at each distance for each of the examined energies revealed a biological Bragg ...

Energy Technology Data Exchange (ETDEWEB)

A unified physically based ion implantation damage model has been developed which successfully predicts both the impurity profiles and the damage profiles for a wide range of implant conditions for arsenic, phosphorus, BF{sub 2}, and boron implants into single-crystal silicon. In addition, the amorphous layer thicknesses predicted by this new damage model are also in excellent agreement with experimental measurements. This damage model is based on the physics of point defects in silicon, and explicitly simulates the defect production, diffusion, and their interactions which include interstitial-vacancy recombination, clustering of same type of defects, defect-impurity complex formation, emission of mobile defects from clusters, and surface effects for the first time. New computationally efficient algorithms have been developed to overcome the barrier of the excessive computational requirements. In ...

CERN Document Server

Mechanics and Natural Philosophy Before the Scientific Revolution

Energy Technology Data Exchange (ETDEWEB)

Particulate Reinforced Titanium matrix composites (PRTi) exhibit some improved specific mechanical properties in comparison with those of unreinforced titanium alloys as a result of the combination of the high strength and stiffness of ceramic particles with the toughness and damage tolerance provided by the metal matrix. The poor tribological properties of the titanium exclude titanium alloys from applications where wear resistance is required (brakes, rotating parts, sliding parts). The addition of ceramic particles improves the tribological properties of metals sensitive to adhesive and /or abrasive wear significantly. In this work, the wear resistance and the friction coefficient of Ti6Al-6V-2Sn reinforced with TiC particles and Ti6Al-4V reinforced with SiC particles (prototype material) are compared with the unreinforced alloys. Pin on disc and pin on ring tests were carried out against standard steel (100Cr6) as a function of pressure, ...

Science.gov (United States)

In acute liver failure following hepatitis, toxic insults, or after major liver surgery, there is an increased bacterial translocation from the gut. This may explain some of the infectious complications seen in these conditions. To elucidate mechanisms and find possible preventive measures, we investigated the effect of rectal administration of arginine and probiotic bacteria (Lactobacillus spp.) on bacterial translocation and the extent of liver failure. Sprague-Dawley rats were used and five different Lactobacillus strains (Lb. reuteri R2LC, Lb. rhamnosus DSM 6594 (= strain 271), Lb. plantarum DSM 9843 (= strain 299v), Lb. fermentum 8704:3 (= strain 245), and Lb. reuteri (= strain 108) were administered rectally once daily for 8 days with and without 2% arginine. Acute liver injury (ALI) was induced on the eighth day by intraperitoneal injection of D-galactosamine (1.1 g/kg body weight), and samples were collected after 24 and 48 hours. Bacterial translocation ...

Energy Technology Data Exchange (ETDEWEB)

During the Bruce A Nuclear Generating Station (BNGS-A) Unit 1 1997 planned outage, a dew point search method identified a leak in one steam generator(SG) tube. Subsequently, the tube was inspected with all available eddy current probes and removed for examination. The initial inspection results and metallurgical examination of the removed tube confirmed that the leak was due to intergranular attack/stress corrosion cracking (IGA/SCC) emanating from the secondary side of the tube at the top of the tubesheet location. Subsequently, eddy current and ultrasonic indications were found at the top of the tubesheet of other Alloy 600 SG tubes. To investigate the source of the indications and to validate the inspection probes, sections of 40 tubes with various levels of damage were removed. The metallurgical examination of the removed sections showed that both secondary side and primary side initiated, circumferential, stress corrosion cracking and intergranular attack ...

International Nuclear Information System (INIS)

''Paraquat lung'' which is complicated with paraquat poisoning has been a lethal pulmonary pathology presenting intra-alveolar fibrosis, but an effective therapy has not been developed so far. We hypothesized that the type II alveolar cells producing surfactant were damaged by paraquat which was actively accumulated through out the blood by alveolar epithelial cells. To prove this hypothesis, we examined the effect of an intratracheal administration of an artificial lung surfactant (surfacten, Mitsubishi Tanabe Pharma Corporation, Osaka) on mortality in a model of murine paraquat poisoning. Paraquat was given intramuscularly 3 days after the intratracheal surfactant administration. The mice used were C57BL/6J strain and Balb/C strain. The lethal dose, 50% (LD50), of paraquat was about 28 mg/kg in the C57BL/6J strain and about 9 mg/kg in the Balb/C strain, respectively. Mortalities of paraquat poisoning in both strains of mice improved significantly when the mice ...

International Nuclear Information System (INIS)

In this work the diffusion of ion-beam-injected self-interstitials (Is) and their interaction with impurities in crystalline Si are presented. In particular, the I penetration into a molecular beam epitaxy grown Si structure was studied by means of diffusion effects induced on B spikes, analyzed by a developed simulation code. Trapping effects at sample-surface and bulk are evidenced and modeled. The B marker approach was extended to the two-dimensional (2D) I-diffusion occurring as a consequence of ion implantation through a sub-micron dimension patterned oxide mask. I-source size effects on the I penetration have been found and modeled, quantitatively describing the 2D I-diffusion. The I-substitutional carbon interactions have been also studied, showing the C ability to effectively retain Is. The I-trapping mechanism was quantitatively studied by the simulation code, showing that one I is able to deactivate about two C traps by means of I-trapping and ...

Energy Technology Data Exchange (ETDEWEB)

The number of reports concerning the chemical toxicology of metals which are released in the environment by natural as well as anthropogenic sources, have been increasing constantly. Lead, cadmium, and manganese have found a variety of uses in industry, craft, and agriculture owing to their physical and chemical properties. The environmental burden of heavy metals has been rising substantially by smelter emission in air and waste sewage in water. Further, organic compounds of lead and manganese used as antiknock substances in gasoline are emitted into the atmosphere by automobile exhaustion. Such environmental contamination of air, water, soil, and food is a serious threat to all living kinds. Although these metals are known to produce their toxic effects on a variety of body systems, much emphasis has been placed on their effects on the nervous system owing to apparent association of relatively low or ''subclinical'' levels of metallic exposure with ...

International Nuclear Information System (INIS)

Neuronal cell death induced by oxidative stress is correlated with numerous neurodegenerative diseases, including Alzheimer's disease (AD), Parkinson's disease (PD), and stroke. The causes of sporadic forms of age-related neurodegenerative diseases are still unknown. Recently, a correlation between paraquat exposure and neurodegenerative diseases has been observed. Paraquat, a nonselective herbicide, was once widely used in North America and is still routinely used in Taiwan. We have used differentiated Human Neuroblastoma (SHSY-5Y) cells as an in vitro model to study the mechanism of cell death induced by paraquat. We observed that paraquat-induced oxidative stress in differentiated SHSY-5Y cells as indicated by an increase in the production of cellular reactive oxygen species (ROS). Furthermore, apoptosis was evident as indicated by cellular and nuclear morphology and DNA fragmentation. Interestingly, pretreatment of SHSY-5Y cells with water-soluble Coenzyme ...

Energy Technology Data Exchange (ETDEWEB)

A comprehensive understanding of dopant activation mechanisms in crystalline Si is required in order to form shallow junctions. In this paper, we will review several experimental assessments on boron clustering and novel methods to form shallow junctions. Boron marker-layer structures have been used to investigate the fundamental aspects of formation and ripening boron-interstitial clusters (BICs) and their influence on the associated transient enhanced diffusion (TED). The samples were damaged by Si implants at different doses in the sub-amorphizing range and annealed at high temperatures. We found that BICs act as a sink for interstitials at supersaturations values S(t)>10{sup 4}. This implies that silicon self-interstitial defects are the primary source of interstitials driving TED, and that BICs act as a secondary 'buffer' for the interstitial supersaturation. These clusters are less sensitive to the ripening ...

Energy Technology Data Exchange (ETDEWEB)

After periodic testing of a large-scale spray calciner/ceramic melter vitrification system over a 2-yr period, sufficient corrosion was noted on various parts of the vitrification system to warrant its disassembly and inspection. A majority of the 316 SS sintered metal filters on the spray calciner were damaged by chemical corrosion and/or high temperature oxidation. Inconel-601 portions of the melter lid were attacked by chlorides and sulfates which volatilized from the molten glass. The refractory blocks, making up the walls of the melter, were attacked by the waste glass. This attack was occurring when operating temperatures were >1200/sup 0/C. The melter floor was protected by a sludge layer and showed no corrosion. Corrosion to the Inconel-690 electrodes was minimal, and no corrosion was noted in the offgas treatment system downstream of the sintered metal filters. It is believed that most of the melter corrosion occurred during one specific operating ...

Science.gov (United States)

The safety of tissue allografts has come under increased scrutiny due to recent reports of allograft-associated bacterial and viral infections in tissue recipients. We report that 50 kGy of gamma irradiation, nearly three times the dose currently used, is an effective pathogen inactivation method when used under optimized conditions that minimize damage to the tissue. Cancellous bone dowels treated with a radioprotectant solution and 50 kGy of optimized irradiation had an ultimate compressive strength and modulus of elasticity equal to conventionally irradiated (18 kGy) and non-irradiated control bone grafts. We subjected bone dowels treated with this pathogen inactivation method to an in vitro cytotoxicity test using three different mammalian cell lines and concluded that the treated grafts were not cytotoxic. The log reduction of nine pathogens spiked into radioprotectant-treated bone irradiated to 50 kGy was also tested. We achieved 4.9 logs of inactivation of a ...

International Nuclear Information System (INIS)

Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanical supported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the MgO(MG-S) with Copper and Fe-Ni Alloy relaxation layers and MgO(MG-NC) ...

Energy Technology Data Exchange (ETDEWEB)

GaAs-based dc high voltage photoguns used at accelerators with extensive user programs must exhibit long photocathode operating lifetime. Achieving this goal represents a significant challenge for proposed high average current facilities that must operate at tens of milliamperes or more. This paper describes techniques to maintain good vacuum while delivering beam, and techniques that minimize the ill effects of ion bombardment, the dominant mechanism that reduces photocathode yield of a GaAs-based dc high voltage photogun. Experimental results presented here demonstrate enhanced lifetime at high beam currents by: (a) operating with the drive laser beam positioned away from the electrostatic center of the photocathode, (b) limiting the photocathode active area to eliminate photoemission from regions of the photocathode that do not support efficient beam delivery, (c) using a large drive laser beam to distribute ion damage over a larger area, ...

Energy Technology Data Exchange (ETDEWEB)

A working visit was made to the National Laboratory for High Energy Physics, Tsukuba, Japan, during the time periods May 16, 1988--June 15, 1988 for the purposes of further evaluation of the high intensity plasma sputter negative ion source and to test the response of the University of Tsukuba 13-MV tandem accelerator to mA intensity level pulsed mode heavy negative ion beams. During the visit, the traveler worked in collaboration with Japanese scientists in installing and testing of the source on the University of Tsukuba tandem electrostatic accelerator injector. During the course of preliminary testing of the ion source and prior to actual injection into the accelerator, sparking began in one or more tube sections, which ultimately led to the decision to replace the damaged tube sections. This problem led to postponement of the scheduled tandem accelerator tests. The traveler attended the Seventh International Conference on Ion Implantation Technology held in ...

International Nuclear Information System (INIS)

Displacements per atom (DPA) is a widely used damage unit for displacement damage in nuclear materials. Calculating the DPA for SiC irradiated in a particular facility requires a knowledge of the neutron spectrum as well as specific information about displacement damage in that material. In recent years significant improvements in displacement damage information for SiC have been generated, especially the energy required to displace an atom in an irradiation event and the models used to describe electronic and nuclear stopping. Using this information, numerical solutions for the displacement functions in SiC have been determined from coupled integro-differential equations for displacements in polyatomic materials and applied in calculations of spectral-averaged displacement cross sections for SiC. This procedure has been used to generate spectrally averaged displacement cross sections for SiC in a ...

Energy Technology Data Exchange (ETDEWEB)

In acute intoxication, uranium (U) not only inhibits bone formation but its excretion in urine also causes renal damage. The former effect is ameliorated by tetracycline (TC), probably due to its chelation property, which might also prevent U deposition in bone. Chemical determination of U incorporated in bone and a histological study of the kidneys were performed on animals injected with U and then treated with TC. The results showed that TC was unable to prevent the binding of U to bone while it exacerbated U-induced renal damage.

Science.gov (United States)

The influence of material configuration and impact parameters on the damage tolerance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based response surfaces. A series of carefully selected tests were used to isolate the coupled influence of various combinations of the number of facesheet plies, core density, core thickness, impact energy, impactor diameter, and impact velocity on the damage formation and residual strength degradation due to normal impact. The ranges of selected material parameters were typical of those found in common aircraft applications. The diameter of the planar damage area associated with Through Transmission Ultrasonic C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. ...

International Nuclear Information System (INIS)

Apparent growth of amorphous layers during low temperature annealing was observed in low energy Ge"+-implanted (0 0 1)Si by high-resolution transmission electron microscopy. The occurrence of abnormal growth is due to the randomization of heavily damaged regions beneath the original amorphous/crystalline interfaces. The randomization process is attributed to the strain, incurred by the presence of a high density of large Ge atoms in the heavily damaged Si substrate, relaxation to lower the free energy of the systems. The randomization upon annealing may be fruitfully applied to minimize the transient enhanced diffusion in shallow junction formation.

Energy Technology Data Exchange (ETDEWEB)

This paper describes examples of the damage resulting from the impact of a whipping pipe on a nearby pressurised pipe. The work is a by-product of a study of the motion of a whipping pipe. The tests were conducted with small-diameter pipes mounted in rigid supports and hence the results are not directly applicable to large-scale plant applications where flexible support mountings are employed. The results illustrate the influence of whipping pipe energy, impact position and support type on the damage sustained by the target pipe.

British Library Electronic Table of Contents (United Kingdom)

Theoretical analysis, modeling, and simulation are used to provide insight into the development of permeability during thermal damage of the high explosive PBX 9501. In a recently published article, Terrones et al. [1] conclude that samples of PBX 9501 thermally damaged at 186 degreeC are not permeable to gas flow in a manner consistent with Darcys Law. We disagree with their conclusion. We show that they have misreported data from the literature, and that their argument depends on a fluid flow model that is physically incorrect and is applied with inappropriate physical parameters.

Science.gov (United States)

The purpose of this study was to evaluate the resin-dentin interfacial morphology and shear bond strength of several new and experimental dentin bonding systems classified as single-bottle/total etch, multi-step/total etch, and self-etching. Class 1 and 5 cavities were prepared from freshly extracted permanent molars and restored with composite resin. Each bonded sample was cross sectioned and one-half was completely demineralized and deproteinized, while the other half was polished along the cut surface to permit measurement of the thickness of resin-infiltrated dentin layer (RIDL) within intertubular dentin (iRIDL) and around the peritubular walls (pRIDL) of resin tags by SEM. Shear bond strength was measured for all the systems 2 minutes after photocuring. SEM showed iRIDL and resin tags of different morphology depending on material and dentin location. The iRIDL was thinner in superficial dentin and thicker in deep dentin. Peritubular RIDL (pRIDL) was thinner than intertubular ...

Energy Technology Data Exchange (ETDEWEB)

Conversion of coal gas into liquid products is a multistep process which involves numerous unit processes. Compared with similar processes using natural gas as feedstock, there are challenges, particularly with the gas purification. There are, however, also advantages when using a carbon-monoxide-rich gas which ultimately may result in a greatly simplified process. This paper discusses the challenges when converting a gas from an entrained coal gasifier into a liquid product and the paper presents the various options available. The following issues will be touched upon: sour gas shift and adjustment of the H{sub 2}/CO ratio; acid Gas Removal (AGR) - when and how; syngas purification; methanol and combined methanol/DME synthesis; gasoline synthesis; future integrated processes. Here, various options are available depending on the gasifier; not only dry or slurry feed but also the question of quench as well as the selected scrubbing temperature are relevant. The WGS ...

International Nuclear Information System (INIS)

Neutron time-of flight spectra were measured from 90 MeV protons and 140 MeV alpha-particle bombardment of Al, Ni, Zr, and Bi at laboratory angles between 20"0 and 130"0. The proton induced neutron spectra reveal three distinct energy regions; a low energy evaporation region, a high-energy region dominated by quasi-free scattering processes and an intermediate-energy region dominated by multi-step, pre-equilibrium processes. In the latter two regions, the spectra show strong angular dependence. The alpha-induced neutron spectra show these same distinct energy regions plus an exponential fall-off above the beam energy per nucleon. The high-energy portions of the forward-angle neutron and proton cross sections are in ratios consistent with the assumption that single nucleon-nucleon scattering dominates. For heavy-mass targets, the low-energy evaporation regions show neutron yields larger than proton yields. The proton-to-neutron ratios observed in the high-energy ...

Science.gov (United States)

Autoreactive cytotoxic CD8 T-cells (CTLs) play a key pathogenic role in the destruction of insulin-producing beta-cells resulting in type 1 diabetes. However, knowledge regarding their targets is limited, restricting the ability to monitor the course of the disease and immune interventions. In a multi-step discovery process to identify novel CTL epitopes in human preproinsulin (PPI), PPI was digested with purified human proteasomes, and resulting COOH-fragments aligned with algorithm-predicted HLA-binding peptides to yield nine potential HLA-A1, -A2, -A3 or -B7-restricted candidates. An UV-exchange method allowed the generation of a repertoire of multimers including low-affinity HLA-binding peptides. These were labeled with quantum dot-fluorochromes and encoded in a combinatorial fashion, allowing parallel and sensitive detection of specific, low-avidity T-cells. Significantly increased frequencies of T-cells against four novel PPI epitopes (PPI(4-13)/B7, ...

International Science & Technology Center (ISTC)

Elaboration of a Modern Technology for Operational Agrometeorological Soil Moisture Monitoring Spring Wheat, Yield and Disease Damage Forecasting and Recommendations for Plant Protection on the Kazakhstan Territory

International Nuclear Information System (INIS)

The purpose of the recommendation is to prevent, to detect, and to remove soiling of guide and retrating blades of steam turbines, e.g. on account of foreign matter in steam dissolved. (TK/LN).

Science.gov (United States)

Design of Damage-Tolerant Composite Sandwich Panels with Tear Straps. Sukra Helitek Inc. 3146 Greenwood Road. Ames, IA 50014-4504 ...

Science.gov (United States)

... a rotating mirror Q-switch or an acousto-optic Q-switch. The former ... Q-switch up to 2000 pps. The Q-switched output bean, is predominantly ...

UK PubMed Central (United Kingdom)

Rheumatoid arthritis (RA) is a debilitating autoimmune disease of global prevalence. The disease is characterized by synovial inflammation leading to cartilage and bone damage. Most of the conventional...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundAlterations in protein composition and oxidative damage of high-density lipoprotein (HDL) have been proposed to impair the cardioprotective properties of...Full Text Available

Science.gov (United States)

Current models of DNA repair of biological damage are reviewed correlating the similarity between carcinogenesis and mutagenesis theories. (PCS)

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Ultra-shallow junction formation in deep submicron Si devices is limited by anomalous diffusion of the dopant, which is related to the release of interstitials from defect clusters formed during the implantation of energetic ions or the subsequent annealing. The work described in this dissertation is concerned with the effects of low energy B ion implantation, especially damage formation, clustering and its annealing. After a review of the stopping and ranges of energetic ions in Si, the formation of implant damage, in particular of point defects, their migration, agglomeration and annihilation, including the involvement of dopant ions, is considered. A description of the Salford ultra low energy implanter is given and the main analysis technique, medium ion energy scattering (MEIS) reviewed. Additional analytical techniques used, such as secondary ion mass spectrometry (SIMS), 4-point probe and cross section transmission microscopy (XTEM) as ...

Science.gov (United States)

Kinetic reaction mechanisms have a hierarchical smacture with mechanisms for complex fuels built up on sub-mechanisms for simple fuel molecules ...

UK PubMed Central (United Kingdom)

BackgroundThe Mre11/Rad50/Nbs1 (MRN) complex is a regulator of cell cycle checkpoints and DNA repair. Defects in MRN can lead to defective S-phase arrest when cells are damaged....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The resistance to microbe damages of aqueous solutions of cutting fluids (SOZh), which contain dual and more complex mixtures of known compounds, is studied. Lauric acid, myristic and tridecanic acid give microbic resistance to the compositions of synthetic cutting fluids. A complexing of the compositions as a rule does not support precisely expressed effects of synergism or antagonism.

UK PubMed Central (United Kingdom)

The histone chaperone Asf1 and the chromatin remodeler SWI/SNF have been separately implicated in derepression of the DNA damage response (DDR) genes in yeast cells treated with genotoxins that cause...Full Text Available

International Nuclear Information System (INIS)

From the frequency of diagnostic radiologic examinations and their radiation dose delivered to the population the risk of cancer induction and genetic damage is calculated on the basis of the risk factors given by the ICRP. Thus 0.38 % and 3 % of the total mortality for cancer and leukemia, resp., can be attributed to X-ray diagnostics. Chest examinations alone result in 0.07-0.7 damages per 100,000 persons depending on the imaging technique applied. (author).

Wastenet

sinensis), the otter (Lutra lutra) and the grey seal (Halichoerus grypus) can be mentioned as ...conflict relates to damage caused by the grey seal to coastal fisheries, whereas in Germany damages ...For example species like the grey seal involved in the conflicts may benefit from the by-catch regulation.

Energy Technology Data Exchange (ETDEWEB)

This book examines the nonlinear optical properties of laser materials. The physical radiation effects on laser materials are also considered. Topics considered include: nonlinear optical properties; nonlinear and harmonic generation materials; two-photon absorption; nonlinear refractive index; stimulated Raman scattering; radiation damage; crystals; and glasses.

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this project is to produce antibodies to unique modified DNA bases and develop immunochemical assays to quantitate these lesions in damaged DNA. During this past year we have developed an antibody and chemical test to quantitate a basic sites in DNA and produced antibodies to the 8-oxopurines. This report discusses the detection of a basic sites in DNA and the preparation of antibodies to 8-hydroxyadenine and 8-hydroxyguanine.

Energy Technology Data Exchange (ETDEWEB)

The developed countries are implementing a policy minimizing damage from environmental pollution by reducing discharge in advance as well as the aftermath of a pollutant. The typical example is to use BAT (Best Available Technology). This is to prevent environmental damage by reducing the discharge of pollutants with available technology and to secure environmental margin to enable industrial activities of future generation. Therefore, the feasibility of introducing BAT requirement system was reviewed by considering foreign examples and Korean situation. 38 refs., 8 figs., 69 tabs.

Energy Technology Data Exchange (ETDEWEB)

The overall objective of this project has been to develop immunochemical methods to quantitate unique DNA base damages in order to facilitate studies on radiation-induced damage production and repair. Specifically, we have been using antibodies raised to damaged bases to quantitate unique lesions in model systems in order to evaluate their potential biological consequences. Our approach has been to synthesize modified nucleotides or nucleosides, conjugate them to protein carriers, and use the conjugates as immunogens in rabbits or to prepare monoclonal antibodies. We have been studying damages that are stable radiolysis products found in X-irradiated DNA and thus of potential biological consequence. Our aim is to build an in vitro and in vivo data base on the interactions between model DNA lesions and such cellular enzymes as DNA polymerases and repair endonucleases. Initial studies have focused on ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... MECHANICAL PROPERTIES, *COPOLYMERS, *SOFT TISSUES, *GELS, *BIOMIMETICS, ISOPRENE, WOUND BALLISTICS, STYRENE PLASTICS ...

Science.gov (United States)

... Accession Number : ADA136144. Title : Characteristics of the Mechanical Properties and the Fractures of an Alpha Beta Titanium Alloy,. ...

Science.gov (United States)

It is important for the trauma surgeon to understand the basic principles of terminal gunshot ballistics and the study of the projectile's effect on striking soft tissue. The amount of kinetic energy dissipated to the tissue is directly related to the mass and velocity of the projectile as follows: K = MV2/2. Doubling the velocity quadruples the energy, while doubling the mass only doubles the energy. A temporary tissue cavity is produced as the striking projectile compresses the surrounding tissue; the higher the energy release, the more extensive the inapparent compressive damage. The permanent cavity that remains is the result of extrusion of tissue from the pathway of the projectile. The higher the velocity, the higher the likelihood of extensive damage. If the missile expands or fragments within the tissues, more damage will occur. PMID:6847483

British Library Electronic Table of Contents (United Kingdom)

Plastic injection molds are an important economic sector due to the increasing use of injection molded plastic components. The selection of mold steel material, its processing conditions, and the way it is machined and hardened all have an impact on how it performs during use across its lifecycle for injection molding. For this study, injection molding conditions seen during high volume manufacturing were used to induce wear that would be typical during processing. A 50wt.% glass fiber reinforced Polybutylene Terephthalate (PBT) was used for the research. After 3000 injection operations, surface damage was found only on the steel used for the stationary half of the mold cavity and the corresponding surface of the molded parts. In contrast, the moving half showed no surface damage or increa...

Energy Technology Data Exchange (ETDEWEB)

Nano photonic materials are synthetically manufactured crystals at the nano scale with the target of creating a microstructure with a special electro-magnetic periodicity. Such nano photonic materials have the ability to control light propagation and thus are capable of creating photonic bandgaps in the frequency domain. We propose using nano photonic crystals as sensors to detect microdamage in composite materials. We demonstrate using a simulation model that a nano photonic sensor attached to a composite bar experiences a significant change in its bandgap profile when damage is induced in the composite bar. The model predicts the frequency response of the nano photonic sensor using the transfer matrix method. A damage metric to evaluate the change in the frequency response is developed. Successful developments of nano photonic sensors allow damage identification at scales not attainable using current sensing technologies.

International Nuclear Information System (INIS)

Imatran Voima Oy , (IVO) operates two Russian designed nuclear power plants of type VVER440/213. Unit 1 has been operating since 1977 and unit 2 since 1981. First damage of feed water distribution (FWD) pipes was observed in 1989. In closer examinations FWD-pipe T-connection and distribution nozzles suffered from severe erosion corrosion damage. Similar damages have been found also in other VVER-440 type NPPs. In 1994 the first FWD-pipe was replaced by a new design mounted over the tube bundle instead of the old FWD-pipe, which was located inside the tube bundle. The purpose of this paper is to describe the new FWD-pipe and discuss its effects on the steam generator chemistry. (author)

International Nuclear Information System (INIS)

The indium implant damage and diffusion behavior in thin silicon-on-insulator (SOI) with a 200 nm top silicon layer were studied for different implantation energies and doses. Rutherford backscattering spectrometry in the channeling mode (RBS/C) was used to characterize the implant damage before and after annealing. Secondary ion mass spectrometry (SIMS) was used to study the indium transient enhanced diffusion (TED) behavior in the top Si layer of the SOI structure. An anomalous redistribution of indium after relatively high energy (200 keV) and dose (1 x 10"1"4 cm"-"2) implantation was observed in both bulk Si and SOI substrates. However, there exist differences in these two substrates that are attributable to the more predominant out-diffusion of indium as well as the influence of the buried oxide layer in the SOI structure.

British Library Electronic Table of Contents (United Kingdom)

The detection and characterization of deeply buried fatigue damage in thick, multi-layer airframe components pose significant technical challenges to the aviation safety community. Currently, no nondestructive evaluation technique is available to reliably detect such potential damage from the exterior of the airframe, which is highly desirable in light of inspection cost as well as avoidance of structure damage. Recent technological advances in high-sensitivity magnetic sensors, i.e., spin-dependent tunneling (SDT) sensors, make it feasible to employ electromagnetic inspection techniques for deep fatigue crack inspection. In this work, we report on the development and fabrication of a low frequency eddy current probe based on a magnetically shielded SDT pickup sensor concentrically located...

Energy Technology Data Exchange (ETDEWEB)

In the flood surveys, it is fundamental to set up the relations of stage-damage. And this makes it possible to evaluate the flood regulation effects of the multipurpose dam and/or levee construction for optimum formulation. Unfortunately in the previous basin studies excluding the Han river basin survey, the conventional approaches on this matter have not been performed due to its time-consuming complexity. In this study we attempted a new method based on the disaster status, and constructed six stage-damage curves along the reaches of the Kum river basin, based upon the flood events records for recent 12 years (1981-92). (author). 12 refs., 3 tabs., 13 figs.

International Nuclear Information System (INIS)

The effects of focused-ion-beam-induced damage on electrical properties of n-type Si are investigated by Schottky contacts. Crystalline Si is exposed to 10-30 keV focused ion beam (FIB), followed by Pt deposition under vacuum of 4x10"-"4 Pa. From current-voltage-temperature measurements, barrier heights of the Schottky contacts are found to increase almost linearly as the FIB energy increases, with the maximum increment of 0.29 eV. The increase is suggested to be related to the arising of acceptorlike defects and an amorphous layer due to FIB damages. A theoretical model is set up to quantitatively describe the barrier height changes.

International Nuclear Information System (INIS)

Channeling effect measurements have been employed to investigate radiation damage produced by 100-keV Ar ions in preferred oriented polycrystalline metal-silicide layers, such as Pd_2Si and NiSi_2 layers formed on single-crystalline Si. For room-temperature implantation, an amount of the damage in Pd_2Si layers was found to saturate at doses between 3 x 10"1"4 and 1 x 10"1"7 ions/cm"2, where the minimum aligned yield of 1.5-MeV He ions was nearly 40% of the random one. On the contrary, it was observed that the NiSi_2 layers became amorphous at doses higher than 3 x 10"1"5 ions/cm"2. These results were confirmed by the reflection electron diffraction analyses.

International Nuclear Information System (INIS)

"9"9"mTechnetium -heat damaged erythrocyte were used as spleen scanning agents in 12 patients from July, 1985 to April, 1986. We used this scan to evaluate situs inversus, asplenia, accessory spleen, hypersplenism, splenic infarction, tumor staging and evaluation of therapy, especially when the "9"9"mTc-tin colloid scans were not definite for diagnosis. The techniques applied to these scans were in vivo/in vitro-labeling method and heating-method to damage the erythrocytes. Liver-to-spleen uptake ratios were increased upto 100:1 and interference from the left lobe of the liver was eliminated. These scans were helpful to evaluate the spleen. (Author).

UK PubMed Central (United Kingdom)

Exercise training is known to induce an increase in free radical production potentially leading to enhanced muscle injury. Vitamins C and E are well known antioxidants that may prevent muscle cell damage....Full Text Available

UK PubMed Central (United Kingdom)

The astonishingly efficient location and excision of damaged DNA bases by DNA repair glycosylases is an especially intriguing problem in biology. One example is the enzyme uracil DNA glycosylase (UNG),...Full Text Available

UK PubMed Central (United Kingdom)

Accessory cusp present on the occlusal surface may seldom pose problems. While its presence may not be a cause for alarm in most instances, it can sometimes lead to serious consequences if it is damaged....Full Text Available

UK PubMed Central (United Kingdom)

DNA double-strand breaks (DSBs) and other lesions occur frequently during cell growth and in meiosis. These are often repaired by homologous recombination (HR). HR may result in the formation of DNA...Full Text Available

UK PubMed Central (United Kingdom)

Reactive oxygen species (ROS), inevitable byproducts of aerobic metabolism, are known to cause oxidative damage to cells and molecules. This, in turn, is widely accepted as a pivotal determinant of...Full Text Available

UK PubMed Central (United Kingdom)

Damaging inflammation arising from autoimmune pathology and septic responses results in severe cases of disease. In both instances, anti-inflammatory compounds are used to limit the excessive...Full Text Available

UK PubMed Central (United Kingdom)

4-Hydroxynonenal (HNE), a major electrophilic product of lipid peroxidation, is regarded as both a marker of oxidative stress and a mediator of oxidative damage. At subtoxic concentrations,...Full Text Available

UK PubMed Central (United Kingdom)

Experiments on Xanthium leaf discs were carried out to determine whether concomitant photoreactivation could be detected and if so, to compare its effects with photoreactivation due...Full Text Available

Science.gov (United States)

... NC 27605 Winnie Liao (919) 821-5950 98-1-02.01-5950 LaRC Design of Damage- Tolerant Composite Sandwich Panels with Tear Straps American Technology ...

Energy Technology Data Exchange (ETDEWEB)

Revised neutron fluence and damage values are reported for the MOTA-2A experiment in the Fast Flux Test Facility (FFTF). This revision corrects an error with processing of the {sup 235}U(n,f) reaction. Net corrections are on the order of 5%.

International Nuclear Information System (INIS)

Exact anatomic knowledge about the location of the gonads and the application of corresponding measures of radiation protection are the preconditions for an efficient reduction of the danger of a possible genetic damage as a result of radiation exposition during X-ray examination of the hip joint of newborns. (VJ).

UK PubMed Central (United Kingdom)

The widely accepted oxidative stress theory of aging postulates that aging results from accumulation of oxidative damage. Surprisingly, data from the longest-living rodent known, naked mole-rats [MRs;...Full Text Available

Science.gov (United States)

Electro-Magnet. Antenna Panels Types Simulated Hail Stone Damage A.Panel ...... X-Band Klystron Electro Magnet. 11. I I. 333-6104 AcBc. 333-6105 Color ...

British Library Electronic Table of Contents (United Kingdom)

The effect of the water-chemical regime (WCR) on damage sustained by heating surfaces of steam generators at NPP is analyzed. It is indicated that phosphate treatment with minimal excesses of phosphates in the steamgenerator water is the most optimal method of managing the WCR regime of horizontal steam generators.

UK PubMed Central (United Kingdom)

BackgroundWe have previously reported that low concentrations of cigarette smoke extract induce DNA damage without leading to apoptosis or necrosis in human bronchial epithelial...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

BackgroundMitochondrial dysfunction, oxidative damage and the accumulation of somatic mutations in mitochondrial DNA (mtDNA) have been associated with certain neurodegenerative disorders....Full Text Available

UK PubMed Central (United Kingdom)

In this paper, we report a method of precise in situ x-ray scattering measurements on protein solutions using small stationary sample cells. Although reduction in the radiation damage...Full Text Available

International Nuclear Information System (INIS)

Most superconductors are quite sensitive to irradiation defects. Critical temperatures may be depressed, critical currents may be increased, by irradiation, but other behaviours may be encountered. In compounds, the sublattice in which defects are created is of significant importance. 24 refs.

International Nuclear Information System (INIS)

Boron is implanted in crystalline silicon through oxide layers with different thicknesses. The implantation is carried out at various doses and energies of interest in ultra large scale integration (ULSI) application. Rapid thermal annealings (RTA) are used to obtain shallow junctions and electrical activation of the B atoms. However, transient enhanced diffusion induced by implantation damage can be observed. The boron concentration profiles before and after annealing are obtained with secondary ion mass spectrometry (SIMS). It is found that the diffusion transient in the tail region of the boron profile increases with decreasing oxide thickness. Even more, if the implantation damage concerns mostly the oxide, i.e. when the concentration peak is located in this oxide, the oxygen knocked into the silicon substrate could play this way an important role in restricting the boron diffusion, which is good to obtain very shallow junctions. On the ...

Energy Technology Data Exchange (ETDEWEB)

A series of cyclic strain controlled tests have been carried out at 600/sup 0/C on three high temperature austenitic iron-based alloys, AISI type 316 stainless steel, Alloy 800 H and Sandvik 253 MA. The tests were carried out under constant total strain control using a constant strain rate of 0.005 s/sup -1/. By considering the changes in modulus throughout the life of each specimen it was found that damage evolution could be successfully predicted as a function of plastic strain range despite the fact that each alloy had been chosen because of a different stress response at 600/sup 0/C. Although each alloy accumulated fatigue damage in a similar manner the longer lives of Sandvik 253 MA and Alloy 800 H at a given total strain range were due to a smaller plastic strain component and a reduced stage I crack propagation rate. In the 253 MA alloy, slip was predominantly planar with some cells occasionally forming at high strain ranges. Slip was ...