Energy Technology Data Exchange (ETDEWEB)

Chemical admixtures are used in dam construction to improve plasticity of the dry materials mixture over time. Roller compacted concrete (RCC) has been used on many dam projects in China. However, the use of RCC has frequently resulted in water reduction problems. This paper provided details of an admixture based on polycarboxylate ether (PCE) which was developed to improve the quality of RCC constructions at the JinHong dam in China. Use of the polymer at the JinHong dam resulted in a vibration sensitive concrete that was sustained over time. Under identical mix-design and compaction conditions in the laboratory, specific gravity of the RCC was increased from 2417 kg/m{sup 3} to 2463 kg/m{sup 3}. The high specific gravity of the material resulted in satisfactory strength data from the dam project. The key-ratio of the splitting tensile strength versus compressive strength was ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The twin-cities of El Paso and Juarez share the water resources of the Hueco Bolson aquifer and overlying Rio Grande aquifer. Both aquifers span the international border between Mexico and the United States. Salinity in the Rio Grande aquifer varies widely, some parts of the shallow aquifer containing less than 1,000 mg/L total dissolved solids (TDS), other parts of the aquifer exceeding 5,000 mg/L TDS. One sizable part of the "Lower Valley" area, approximately 45 km below El Paso contains very dilute water near the outer edge of the floodplain. Historically it had been thought that the dilute waters in this location were derived from recharge from arroyos that drained proximal parts of the Hueco Bolson. Instead, our hydrogen and oxygen isotope data and carbon-14 data indicate that these dilute waters were derived from pre-dam infiltration of the Rio Grande. Relatively light and slightly evaporated pre-dam waters (-11.5 del O18) at the ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Topics concerning the problems associated with older and aging dams are considered including: what can be done to extent the lifetime of an old dam, the decision to decommission a dam based on a value judgment that the risk of maintaining the dam is too great for society's acceptance, the possibility of change in the level of risk tolerance with time in a technological environment, traditional surveillance methods used by dam owners in the Y2K situation, and the unreality of dam immortality. Trends and means for preserving older dams for their owner's purposes are outlined, as well as their lifetime compared to that of the downstream systems they serve. Despite the fact that we live in a throwaway society, dam owners cannot just leave their dam asset when they are through with using ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Reliability analysis is now being used to a large extent for several civil engineering structures. Such analysis has not been used for rockfill dams, the most common dams in Norway. Following work on reliability analysis for breakwaters, reliability analysis was then used to investigate the ability of the stone material on the upstream face of a rockfill dam to withstand wind generated waves. An attempt is made to follow up this work by including discharge overtopping on a rockfill dam in a reliability analysis. This report primarily goes through previous work on the required weight of protective stones on the downstream face of the dam for specified discharges over the dam and also deals with the probability formulation of extreme floods. A failure function with partial coefficients is formulated. But for reasons of economy the calibration of the partial ...

Energy Technology Data Exchange (ETDEWEB)

A stochastic analysis is presented of the probability of overtopping of a dam. The discussion is based on the case of a dam for a small water storage reservoir which has recently been constructed in the Saar district in the FRG. The problem is first solved by means of a simulation method. However, it is possible to describe the result of the sumulation method by means of a much simpler model which is based on a solution of the failure integral of Freudenthal for uncorrelated resistances and loads. It is shown that the actual safety of this dam against overtopping is extremely sensitive to both the operation rule for the reservoir, and the freeboard allowance. Some general conclusions are derived from this study for assisting in the ongoing discussion of dam safety. (6 figs, 1 tab, 7 refs)

International Nuclear Information System (INIS)

Some considerations regarding ice load in risk-based dam safety analysis are presented for small concrete dams. The most significant physical mechanisms leading to ice thrust on dams (such as thermal expansion and water level fluctuations) are outlined. Published literature on dam ice loads to examine ice load magnitude-return period relationships, sliding and overstressing failure mechanisms and structural performance criteria to resist ice loads, are also reviewed. Related loading combinations for structural safety evaluations were determined regarding the issue of simultaneity of ice loads with other events such as earthquakes. Parametric analyses were conducted on a small gravity dam section, 3m high, and a taller dam, 17.9 m high, to demonstrate the ultimate ice load carrying capability as a function of dam geometry and shear and ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Norwegian Open Research Archives (NORA)

Full Text Available

CERN Document Server

In the present study, applications of the SPH method to industrial related issues are considered by starting from an existing open source 2D SPH code, namely the SPHYSICS code, which offers an effective ground for numerical developments, which are performed in order to bring an answer to industrial problems, such as simulations of solid/fluid coupling in a free surface flow context. The purpose of the present paper is therefore to expose the numerical developments which yield an enhanced version (referred to as "SPHYSIC2") of the initial code. Firstly, the different features added to obtain the operational code needed for engineering applications are described, and so are the problems raised on this way, offering a kind of review of SPH methods for engineers. Secondly, the validation of the proposed code is partially presented with two well known but difficult test cases, namely the classical "dam break" and "wedge entry" problems. Thirdly, ...

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Swamp is a 3,020 Ha forested wetland on the floodplain of the Savannah River and is located on the Department of Energy`s Savannah River Site (SRS). Major impacts to the swamp hydrology occurred with the completion of the production reactors and one coal-fired powerhouse at the SRS in the early 1950`s. Water was pumped from the Savannah River, through secondary heat exchangers of the reactors, and discharged into three of the tributary streams that flow into the swamp. This continued from 1954 to 1988 at various levels. The sustained increases in water volume resulted in overflow of the original stream banks and the creation of additional floodplains. Accompanying this was considerable erosion of the original stream corridor and deposition of a deep silt layer on the newly formed delta. Heated water was discharged directly into Pen Branch and water temperature in the stream often exceeded 50 C. The nearly continuous flood of the swamp, the ...

Science.gov (United States)

... similar to the S-wave tests except that exploding bridgewire detonators (EBW's) were used as the P-wave source. Crosshole ...

British Library Electronic Table of Contents (United Kingdom)

SummaryA meshless numerical model is proposed to investigate shallow-water dam break flows in 1D open channels. The numerical model is to solve the shallow water equations (SWE) based on smoothed particle hydrodynamics (SPH). The concept of slice water particles (SWP) is adopted in the SPH-SWE formulation. The numerical sensitivity analysis is first performed to study the appropriate SWP number and variable smoothing length through dam break flows in an idealized 1D channel with dry/wet beds. Extensive validation by comparison with laboratory and field data is next conducted for four benchmark problems, including dam break flows through a rough flat channel, a rough bumpy channel with various downstream boundary conditions, a nonprismatic channel, and a realistic scale model of the Toce ri...

International Nuclear Information System (INIS)

This study was designed to quantitate the dose resulting from lead exposure during the critical periods of brain development during gestation by determining: (1) if blood lead concentration in rat dams is affected by pregnancy status or duration of lead exposure, (2) if lead concentration in fetuses is associated with the duration of dam exposure, (3) the rates of lead absorption and elimination in pregnant and nonpregnant dams; and (4) the effect that prebreeding exposure on lead kinetics in the dam and upon fetus blood lead concentrations. The results of experiments in which the dams' drinking water contained 50 mg/L lead indicate blood lead levels (after normalizing by water consumption on a body weight basis) of pregnant rats are significantly higher than blood lead levels of non-pregnant rats. Statistical differences in blood lead levels were observed by day 15 of gestation and ...

International Nuclear Information System (INIS)

Total river discharge in Pakistan in summer season vary from 3 thousand to 34 thousand cusses (100 thousand Cusses to 1,200 thousand Cusses) and can cause tremendous loss to human lives, crops and property, this causes the loss of most of the flood water in the lower Indus plains to the sea. Due to limited capacity of storage at Tarbela and Mangla Dams on river Indus and Jhelum, with virtually no control on Chenab, Ravi and Sutlej, devastating problems are faced between July and October in the event of excessive rainfall in the catchments. Due to enormous amounts of sediments brought in by the feeding rivers, the three major reservoirs -Tarbela, Mangla and Chashma will lose their storage capacity, by 25 % by the end of the year 2010, which will further aggravate the water-availability situation in Pakistan. The quality of water is also deteriorating due to urbanization and industrialization and agricultural developments. On the Environmental Front the main problems ...

International Nuclear Information System (INIS)

Dams and reservoirs are among one of the most sensitive of all development Project, in terms of pervasiveness of their influence in altering the environmental conditions and resources. In the present study, major dams and reservoir projects are reviewed, from the environmental point of view. Dams and Reservoir projects bring about major changes in the immediate environment, thus affecting public health, settlements, farmlands, roads and historical sites. Impacts on human population and wildlife may be profound. Tropical diseases, involving fresh-water hosts or vectors in their transmission, are often common around new reservoirs. Large lakes create limnological changes, excessive evaporation, seepage, disturbance in water-table and increased tendencies of landslides and earthquakes. Micro climatic changes are possible, such as fog formation, increased cloudiness and modified rainfall-patterns. Retention of sediment results ...

International Nuclear Information System (INIS)

For the treatment of dam waste water containing micro quantities of uranium, the so-called chemical precipitation method is conventionally used, that is, acidic sodium phosphate is added to it and so the uranium (UO_2"2"+) is removed in coprecipitation with the then occurring calcium phosphate (solid). The method, however, has several problems, such as the large space required and large quantities of sludge. For the pupose of eliminating such difficulties and removal and recovery of the uranium, development of the new uranium adsorption method was started. Of the many uranium adsorbents available, excellent ones were selected and then the continuous treatment test was made with small apparatus. Subsequently, the dam waste water uranium recovery facility was completed in 1983. (Mori, K.).

Energy Technology Data Exchange (ETDEWEB)

This conference provided a forum for more than 500 delegates from industry, government universities and research centres to share their professional knowledge on research and development that affects all sectors of geotechnical engineering, applied geology and hydrogeology. Accomplishments in the geoenvironmental field were also highlighted. The geotechnical sessions were entitled: pile foundations and load testing; excavations and special foundation issues; reinforced soil and soil-structure interactions; advances in modelling, constitutive issues; advances in modelling, consolidation and other applications; advances in modelling, discrete elements and slope stability; embankments and dams; landfills and barriers; fundamental soil mechanics; soil mechanics and ground movement; GIS and remote sensing; landslides and slopes; cone penetration tests and liquefaction assessment; rock mechanics; engineering geology; geoenvironmental sustainability; oilsand and petroleum ...

Energy Technology Data Exchange (ETDEWEB)

This report examines the use of probabilistic methods in dealing with the problem of potential earthquake-induced liquefaction of foundation soils at an example dam site located in the central United States, near the New Madrid earthquake zone. The example dam is assumed to be a 1-mile long rolled-filled embankment founded on a 100-ft deep deposit of interbedded alluvial gravels, sands, silts, and clays. The study is seen as an opportunity to examine probabilistic concepts and procedures in the framework of an example engineering project. In this context, the main practical value of a probabilistic approach is that it permits more informed decision making about further data acquisition, additional engineering analysis, and if necessary, remedial action. The specific aim of the study is to show how probabilistic procedures complement and help to reinterpret the results of deterministic (earthquake-induced) liquefaction analysis. The procedures ...

Energy Technology Data Exchange (ETDEWEB)

The guiding mechanism is attached by a hinge (swivel) to the supporting frame, and the frame is equipped by hinges (swivels) with hydraulic or pneumatic cylinders mounted on its ends and is attached by hinges (swivels) to the coke ejector and guide respectively. This increases the productivity and efficiency of operating the system.

Wastenet

Pumped storage plants 20 are a relatively common type.They use a dam to create an upper reservoir ...Some pumped storage plants use the same water turbine and electric generator for both operating periods.That is,

UK PubMed Central (United Kingdom)

On the west flank of the Wind River Mountains, Wyoming, are several large lakes occupying glacially scoured depressions dammed by terminal moraines. Fremont, Willow, and New Fork Lakes, having maximal...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Failure of a dam is something we hope never happens. But if a failure occurs, it`s important to study the circumstances in order to expand our knowledge base, and then apply what we learn to other structures.

Energy Technology Data Exchange (ETDEWEB)

In 1996, the National Marine Fisheries Service and the University of Washington completed the fourth year of a multi-year study to estimate survival of juvenile salmonids (Oncorhynchus spp.) passing through dams and reservoirs on the Snake River. Actively migrating smolts were collected near the head of Lower Granite Reservoir and at Lower Granite Dam, tagged with passive integrated transponder (PIT) tags, and released to continue their downstream migration. Individual smolts were subsequently detected at PIT-tag detection facilities at Lower Granite, Little Goose, Lower Monumental, McNary, John Day and Bonneville Dams. Survival estimates were calculated using the Single-Release (SR) and Paired-Release (PR) Models. Timing of releases of tagged hatchery steelhead (O. mykiss) from the head of Lower Granite Reservoir and yearling chinook salmon (O. tshawytscha) from Lower Granite Dam in 1996 spanned the ...

Science.gov (United States)

Populations of a common forage fish, red shiner Notropis lutrensis, were sampled from four localities on the Brazos River, Texas, affected by cold-water discharge from a hydroelectric dam and from unaltered sites in the same region. Polymorphism at the Mdh-B locus, encoding supernatant malate dehydrogenase, indicates that populations within 57 km of the dam are distinctive from other regional populations and possess a unique Mdh-B allele, have significantly higher levels of heterozygosity at the Mdh-B locus, represent a homogeneous set that have significantly different Mdh-B zygotic frequencies from other regional populations, and have significantly different Mdh-B zygotic proportions than would be expected under a Hardy-Weinberg equilibrium. Increased levels of heterozygosity in fish within 57 km of the dam were correlated with discharge-associated fluctuations in water temperature at sampling stations.

British Library Electronic Table of Contents (United Kingdom)

Our understanding of prenatal behavior has been significantly advanced by techniques for direct observation and manipulation of unanesthetized, behaving rodent fetuses with intact umbilical connections to the mother. These techniques involve brief administration of an inhalant anesthesic, enabling spinal transection of the rat or mouse dam, after which procedures can continue with unanesthetized dams and fetuses. Because anesthetics administered to the mother can cross the placental barrier, it is possible that fetuses are anesthetized to varying degrees. We compared in perinatal rats the effects of prenatal maternal exposure to two inhalant anesthetics: ether and isoflurane. Fewer spontaneous fetal movements and first postpartum nipple attachments were observed following maternal exposure...

International Nuclear Information System (INIS)

Diurnal and seasonal thermal constancy, a greatly delayed seasonal temperature maximum, and summer cool and winter warm conditions characterize the stream environment below a deep-release dam in Colorado. Low diversity index and equitability values and changes in macroinvertebrate species composition may result from failure of the temperature regime to provide the thermal stimuli essential for various life-cycle phenomena. It is hypothesized that the following sublethal effects, directly or indirectly resulting from the modified temperature regime, may further alter macroinvertebrate community structure: reduction of niche overlap and a shift toward an equilibrium community as a consequence of reduced environmental fluctuation; more intense competition associated with greater productivity; elimination of major invertebrate predators; and failure of the limited temperature range to provide optimal temperatures for various physiological processes. Effects of the ...

Energy Technology Data Exchange (ETDEWEB)

This Executive Summary, Volume I, of the lower Flathead System Fisheries Study Final Report, was prepared to provide a study overview for persons who are not fisheries scientists. The contents provide an introduction to the study and its objectives, a short description of the study area, a discussion of the major findings and conclusions of the study, and the description of fisheries management alternatives available to managers of the lower Flathead system. Technical reports were prepared for those portions of the study dealing with the lower Flathead River and its tributaries, Volume II, and the South Bay of Flathead Lake, Volume III. The annual hydrographic regime of the Flathead system, consisting of upper rivers, lake and lower river, has been modified by the construction and operation of two major hydroelectric facilities, Hungry Horse Dam on the south fork Flathead River and Kerr Dam at the outlet of Flathead Lake. The modified ...

Energy Technology Data Exchange (ETDEWEB)

Design-for-reliability concepts can be applied to the products of the construction industry, which includes buildings, bridges, transportation systems, dams, and other structures. The application of a systems approach to designing in reliability emphasizes the importance of incorporating uncertainty in the analyses, the benefits of optimization analyses, and the importance of integrating reliability, safety, and security. 4 refs., 3 figs.

Energy Technology Data Exchange (ETDEWEB)

Acid Rock Drainage (ARD) is the product formed by the atmospheric oxidation of the relatively common pyrite and pyrrhotite. Waste rock dumps and tailings containing sulfide mineral have been reported at toxic materials producing ARD. Mining in sulphide bearing rock is one of activity which may lead to generation and release of ARD. ARD has had some major detrimental affects on mining areas. The purpose of this study was carried out to develop disposal method for preventing contamination of water and soil environment by waste rocks dump and tailings, which could discharge the acid drainage with high level of metals. Scope of this study was as following: environmental impacts by mine wastes, geochemical characteristics such as metal speciation, acid potential and paste pH of mine wastes, interpretation of occurrence of ARD underneath tailings impoundment, analysis of slope stability of tailings dam etc. The following procedures were used as part of ARD evaluation and ...

Energy Technology Data Exchange (ETDEWEB)

The probabilistic external events analysis performed for the Savannah River Site K-reactor PRA considered many different events which are generally perceived to be external'' to the reactor and its systems, such as fires, floods, seismic events, and transportation accidents (as well as many others). Events which have been shown to be significant contributors to risk include seismic events, tornados, a crane failure scenario, fires and dam failures. The total contribution to the core melt frequency from external initiators has been found to be 2.2 {times} 10{sup {minus}4} per year, from which seismic events are the major contributor (1.2 {times} 10{sup {minus}4} per year). Fire initiated events contribute 1.4 {times} 10{sup {minus}7} per year, tornados 5.8 {times} 10{sup {minus}7} per year, dam failures 1.5 {times} 10{sup {minus}6} per year and the crane failure scenario less than 10{sup {minus}4} per year to the core melt ...

International Nuclear Information System (INIS)

The distribution of lead in lactating mice and suckling offspring was studied with whole body autoradiography at 4 and 24 h after a single intravenous injection of "2"0"3Pb (50 mmol Pb/kg) to the dams. In the lactating mice on day 14 of lactation, the highest uptake of radioactivity at 4 h after administration was recorded in renal cortex, skeleton and liver. A high uptake was also evident in the mannary gland. At 24 h after administration, the radioactivity had decreased in most organs except in the skeleton. In the suckling pups, exposed to lead only via dams' milk for 24 h, the highest level of radioactivity was present in the intestinal mucosa and a much lower level of radioactivity was present in the skeleton. The mammary glands from mice given three daily intravenous injections of 240 #mu#mol Pb/kg were examined with X-ray microanalysis. At 4 h after the last injection, lead was found associated with casein micelles both inside the ...

International Nuclear Information System (INIS)

Results of an evaluation of 18 different products that can be used as waterstops in hydraulic dams to minimize or eliminate leaks at construction joints, were discussed. The materials were tested for permeability and adherence at 23, 15 and 5 degrees C. A two-component polyurethane resin product was found to be the one that best fulfilled the evaluation criteria. It was also found that the successful injection of a borehole depends not only on selecting the product with the best performance characteristics, but also on the technique used. Hence the preparation of the resin and the pressure at which it is injected are important performance criteria. 5 refs., 6 photos, 4 figs.

International Nuclear Information System (INIS)

The mine dumps that arise from the gold mining operations in South Africa are a potential source of high concentrations of radon (222"Rn). Studying the diffusion of radon and the emanation from the soil will help to deduce the radon flux from these dumps to identify the problem areas for rehabilitation. This study describes measurements of the emanation coefficient and the modelling of the depth profile of the radon activity concentration, which is compared to a depth profile that was measured on such a mine dump. Emanation coefficients ranging from 0.13 to 0.39 have been obtained.

Energy Technology Data Exchange (ETDEWEB)

The Asejire dam at Ibadan, Nigeria was constructed in the late sixties for the purpose of providing water for the city of Ibadan (presently about 4,5 million inhabitants). It is located on the Oshun river approximately fifteen miles from the city. In 1982 cracks were observed on the wing walls and although these continued to develop, no attempt was made at that time to investigate their causes and no repair was carried out. In 1989 the SGI ENGINEERING Group of Geneva, Switzerland was appointed as the consultant for the complete refurbishment of the Asejire water scheme. The consortium Degremont-Poat-Clemessy was awarded the contract for the project. The African Development Bank and the Nigerian Government have provided the loan to finance the project.

International Nuclear Information System (INIS)

The Washington Department of Fish and Wildlife (WDFW) has been contracted through the Bonneville Power Administration (BPA) and the Grant County Public Utility District (GCPUD) to perform an evaluation of juvenile fall chinook salmon (Oncorhynchus tshawytscha) stranding on the Hanford Reach. The evaluation, in the fourth year of a multi-year study, has been developed to assess the impacts of water fluctuations from Priest Rapids Dam on rearing juvenile fall chinook salmon, other fishes, and benthic macroinvertebrates of the Hanford Reach. This document provides the results of the 2000 field season.

International Nuclear Information System (INIS)

The Washington Department of Fish and Wildlife (WDFW) has been contracted through the Bonneville Power Administration (BPA) and the Grant County Public Utility District (GCPUD) to perform an evaluation of juvenile fall chinook salmon (Oncorhynchus tshawytscha) stranding on the Hanford Reach. The evaluation, in the second year of a multi-year study, has been developed to assess the impacts of water fluctuations from Priest Rapids Dam on rearing juvenile fall chinook salmon, other fish species, and benthic macroinvertebrates of the Hanford Reach. This document provides the results of the 1998 field season.

Science.gov (United States)

Intercrosses of heterozygous pro-opiomelanocortin (POMC) mice result in homozygous null progeny at lower frequencies than expected. Genotyping offspring at pre-, peri-, and postnatal stages revealed that over half of homozygous null mutants die in the early postnatal stages. To investigate the reasons for this early postnatal lethality, we analyzed in detail different parameters in the initial hours after birth. POMC null mutants born to heterozygous dams presented at birth with corticosterone levels no different from wildtype littermates, were euglycemic, and had normal liver glycogen stores. However, already 30 min after birth corticosterone levels dropped by 80% and were undetectable thereafter, while corticosterone levels in wildtype animals increased during postnatal hours. Circulating adrenaline was almost below detection 1h after birth. Blood glucose levels fell sharply in all genotypes within 30 min after birth; however, wildtype and heterozygous pups ...

Science.gov (United States)

Surface temperature is measured with an infrared thermometer. Measuring Surface Temperature. Nine sample points are selected with a site of uniform land ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the project implementation and monitoring of all habitat activities that occurred over Fiscal Year 2002 (FY 02). Some of the objectives in the corresponding statement of work for this contract were not completed within FY 02. A description of the progress during FY 02 and reasoning for deviation from the original tasks and timeline are given. OBJECTIVE 1--Provide coordination of all activities, administrative oversight and assist in project implementation and monitoring activities. Administration oversight and coordination of the habitat statement of work, budget, subcontracts and personnel was provided. OBJECTIVE 2--Develop, coordinate, and implement the Hood River Fish Habitat Protection, Restoration, and Monitoring Plan. The Hood River Fish Habitat Protection, Restoration, and Monitoring Plan was completed in 2000 (Coccoli et al., 2000). This document is utilized for many purposes including: drafting the Watershed Action Plan, ranking projects for funding, and ...

International Nuclear Information System (INIS)

The extraction of Am(III) and Eu(III) has been investigated using mixtures of synthesized aromatic dithiophosphinic acids (R_2PSSH) and tributylphosphate (TBP), trioctylphosphine oxide (TOPO) or tributylphosphine oxide (TBPO) in toluene from nitric acid (0.01-1.5 mol l"-"1). There was no detectable extraction when R_2PSSHs were used alone as extractants for either Am(III) or Eu(III) (D_A_m_,_E_u<10"-"4) under the experimental conditions used in this study. High separation factors (D_A_m/D_E_u>20) with D_A_m>1 were achieved in the nitric acid range 0.1-1 moll"-"1 by means of a synergistic mixture of bischlorodithiophosphinic acid with TBP, TOPO or TBPO. (orig.)

Science.gov (United States)

Three in vivo assays were used to measure the immunocompetence of chickens in two generations of a selection experiment. The obtained data were used to estimate the variance components for sire and dam for antibody production to Pasteurella multocida and Mycoplasma gallisepticum vaccines, for T-cell-mediated immunity evaluated by a phytohemagglutinin wing web assay, and for clearance of foreign particles from the circulatory system. Heritabilities of and genetic correlations among these immunological traits were calculated from the sire variance components. Heritability estimates of the immunological traits based on the sire component of variance ranged from .06 to .53, and genetic correlations among immunological traits were generally negative. PMID:1956847

British Library Electronic Table of Contents (United Kingdom)

SummaryThis paper examines the sensitivity and uncertainty of evaporation estimates from Nasser Lake, south of Egypt using data collected at the floating station Raft, 2km upstream of the Aswan High Dam, and 12 evaporation models. Based on their approach the evaporation models were ranked in five classes, respectively the Bowen ratio energy budget (BREB) approach, three energy-aerodynamic based methods, a mass transfer method, two temperature and five solar radiation-temperature approaches. State dependent parameter models were used to estimate the sensitivity indices of the different evaporation estimation methods at daily and monthly frequencies. A drastic reduction in the cost of the sensitivity analysis was obtained when coupled with efficient sampling methods, producing quasi-Monte Ca...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This study evaluated potential hydrogeologic mechanisms that may account for increasing moisture content conditions within the sediments of hydroelectric earth dams. Many such dams in Canada are reaching their life spans of approximately 40 years, therefore this study is considered to be an important and timely undertaking. The objective was to develop a method to numerically assess transient groundwater flow processes within old earth structures. The focus of this study was central Manitoba's Grand Rapids Generating Station where progressive movement within the till overburden has been observed since 1977. The possible source of water which is causing higher moisture content and weakness in the overburden material may be the slow wetting-up of the core and progressive increase in seepage to the downstream side. The evolution of flow through the core was evaluated with a modelling program called FRAC3D-VS which accounts for transient ...

Energy Technology Data Exchange (ETDEWEB)

Work continued on the correlations of catalytic activity of metals and surface structure. Work is described in the following areas: CO oxidation on a Cu/Rh(100) Bimetallic catalysts; electronic properties of bimetallic surfaces; and reflection absorption spectroscopy of bimetallic surfaces. 5 figs. (CBS)

Energy Technology Data Exchange (ETDEWEB)

The specific research goal of this project is to identify means to restore and rebuild the Snake River white sturgeon (Acipenser transmontanus) population to support a sustainable annual subsistence harvest equivalent to 5 kg/ha/yr (CBFWA 1997). Based on data collected, a white sturgeon adaptive management plan will be developed. This 2001 annual report covers the fifth year of sampling of this multi-year study. In 2001 white sturgeon were captured, marked, and population data were collected in the Snake and Salmon rivers. The Snake River was sampled between Lower Granite Dam (rkm 174) and the mouth of the Salmon River (rkm 303), and the Salmon River was sampled from its mouth upstream to Hammer Creek (rkm 84). A total of 45,907 hours of setline effort and 186 hours of hook-and-line effort was employed in 2001. A total of 390 white sturgeon were captured and tagged in the Snake River and 12 in the Salmon River. Since 1997, 36.1 percent of the tagged white sturgeon ...

Wastenet

...Surface Aerators Products and Equipment Find and compare a variety of surface aerators products and equipment on the world's largest environmental industry portal. ...

Energy Technology Data Exchange (ETDEWEB)

Two major developments have given impetus to wider adoption of variable-speed turbine/generators in hydroelectric plants, both essentially environmental: (1) the need for stream-bed stability below river dams, and (2) the need to minimize fish damage. Also, the need to stabilize pumped-storage and generating efficiencies to match extreme changes in head levels has been a driving force. Variable-speed operation in hydro applications is relatively new to North America. In other parts of the world, it has been used in pumped-storage plants since 1971. In the US, and increasing potential exists for variable-speed hydro, considering the 30 pumped-storage plants already in operation and several river plants struggling with high head fluctuations--including four at stations operated by the Bonneville Power Administration. Several modifications to hydro-plant hardware and operating procedures are actively being considered at Bonneville--all of them practical but costly. ...

International Nuclear Information System (INIS)

A brain weight deficit of about 70 mg was induced at doses of approximately 75-mGy and a deficit of 60 mg was induced at 100 mGy. This confirms the effects projected and observed by Wanner and Edwards. Although the data do not demonstrate a clear dose-response relationship between the 75-mGy and 100-mGy groups, the data are statistically consistent with a dose-response effect because of the overlapping confidence intervals. The lack of a statistically significant observation is most likely related to the small difference in doses and the limited numbers of animals examined. There are several factors that can influence the brain weight of guinea pig pups, such as caging and housing conditions, the sex of the animal, and litter size. These should be taken into account for accurate analysis. Dam weight did not appear to have a significant effect. The confirmation of a micrencephalic effect induced x rays at doses of 75-mGy during this late embryonic stage of ...

International Nuclear Information System (INIS)

Absorption of lead is known to be enhanced during infancy. In this study, the sites of intestinal accumulation of Pb by suckling rats have been determined under various conditions using "2"0"3Pb as a tracer. When "2"0"3Pb was administered intragastrically (IG) as a soluble salt, accumulation occurred primarily in the duodenum, regardless of dose and vehicle. In contrast, when rat pups suckled from a dam which had received "2"0"3Pb, the only region of the small intestine showing accumulation of radioactivity was the ileum. To confirm that these differences were not related to the route of administration, rat milk was labeled with "2"0"3Pb and was then used for IG administration. Once again, accumulation (4 hr post-administration) was confined to the ileum. When the dose was increased 10-fold, milk Pb displayed some accumulation in duodenal tissue, but very much less than that of soluble Pb at the same time and dosage. At 20 hr postadministration, there was ...

International Nuclear Information System (INIS)

An aerial radiological survey of the Oak Ridge Reservation (ORR) and surrounding area in Oak Ridge, Tennessee, was conducted during the period March 30 to April 14,1992. The purpose of the survey was to measure and document the terrestrial radiological environment of the Oak Ridge Reservation for use in environmental management programs and emergency response planning. The aerial survey was flown at an altitude of 150 feet (46 meters) along a series of parallel lines 250 feet (76 meters) apart and included X-10 (Oak Ridge National Laboratory), K-25 (former Gaseous Diffusion Plant), Y-12 (Weapons Production Plant), the Freels Bend Area and Oak Ridge Institute for Science and Education, the East Fork Poplar Creek (100-year floodplain extending from K-25 to Y-12), Elza Gate (former uranium ore storage site located in the city of Oak Ridge), Parcel A, the Clinch River (river banks extending from Melton Hill Dam to the city of Kingston), and the CSX Railroad Tracks ...

International Nuclear Information System (INIS)

The paper presents experimental investigations of main features of plasma surface interaction and energy transfer to the material surface in dependence on plasma heat loads. The experiments were performed with QSPA repetitive plasma pulses of the duration of 0.25 ms and the energy density up to 2.5 MJ/m2. Surface morphology of the targets exposed to QSPA plasma screams is analyzed. Relative contribution of the Lorentz force and plasma pressure gradient to the resulting surface profile is discussed. development of cracking on the tungsten surface and swelling of the surface are found to be in strong dependence on initial temperature of the target.

Science.gov (United States)

In this paper we investigate the effects of surface mediation on the adsorption behavior of argon at different temperatures on homogeneous graphitized thermal carbon black and on heterogeneous nongraphitized carbon black surface. The grand canonical Monte Carlo (GCMC) simulation is used to study the adsorption, and its performance is tested against a number of experimental data on graphitized thermal carbon black (which is known to be highly homogeneous) that are available in the literature. The surface-mediation effect is shown to be essential in the correct description of the adsorption isotherm because without accounting for that effect the GCMC simulation results are always greater than the experimental data in the region where the monolayer is being completed. This is due to the overestimation of the fluid-fluid interaction between particles in the first layer close to the solid surface. It is the ...

Science.gov (United States)

A compact heat exchanger pedestal array for augmenting heat transfer in a machine is disclosed. The compact heat exchanger pedestal array includes a wall having first and second surfaces. The first surface faces a heated flow path and the second surface p...

Energy Technology Data Exchange (ETDEWEB)

In the present work, we describe application of binary pseudo-random gratings (BPRG) and arrays (BPRA) as effective 1D and 2D test surfaces suitable for calibration of different surface profilometers, including a number of interferometric microscopes and scatterometers.

Science.gov (United States)

Engine flow simulation was provided by four separately mounted air ejectors connected to a high-pressure air supply. The engine nacelle center lines were ...

International Nuclear Information System (INIS)

The variation of surface composition and sintering of the binary Pd_7Ag_3 nanoparticles prepared by chemical reduction were studied. The composition of the as-prepared Pd_7Ag_3 nanoparticles across the diameter is inhomogeneous due to different reduction potentials of Pd and Ag. Upon heating, Ag will migrate to the surface because of its lower surface energy. Surface modification results in variation of surface composition during the sintering process. Stearic acid acts as a grain growth inhibitor. The migration of Ag to the surface is suppressed and the sintering is retarded. Modification by polyethylene glycol leads to more migration of Ag atoms from the core to the surface. This makes the nanoparticles easier to sinter.

Science.gov (United States)

... GRIT-BLAST/SILANE (GBS) ... GRIT-BLAST/SILANE (GBS) ALUMINUM SURFACE PREPARATION FOR STRUCTURAL ADHESIVE BONDING 5b. ...

Science.gov (United States)

Infrared Thermometer: Ground surface temperature averaged 60-sec at 10-meter height

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The surface properties of copper-refractory metal (CU-RF) alloy bodies are modified by heat treatments which cause the refractory metal to form a coating on the exterior surfaces of the alloy body. The alloys have a copper matrix with particles or dendrites of the refractory metal dispersed therein, which may be niobium, vanadium, tantalum, chromium, molybdenum, or tungsten. The surface properties of the bodies are changed from those of copper to that of the refractory metal.

International Nuclear Information System (INIS)

Results of self-consistent local-spin-density-functional calculations are reported for the first time for the Ni(110) surface, represented by one-, three-, and five-layer slabs. Calculations for one- and five-layer slabs of Ni(100) are also reported. The behavior of the surface magnetization with varying slab thickness elucidates the nature and origin of the surface magnetic moment. We predict a 13% enhancement of the Ni(110) surface magnetic moment compared to the bulk value. For the Ni(100) surface, we find a smaller surface enhancement about 7%, compared to bulk, which agrees with the results of Jepsen et al. The enhancement of surface magnetic moments on Ni(100) and Ni(110) surfaces is attributed to s-d dehybridization at the surface and to the presence of electrostatic shifts required to ...

Energy Technology Data Exchange (ETDEWEB)

In a reactor environment, the surface of a limiter or wall is primarily determined by the mechanism of erosion and deposition of surface material. It should be possible to use pellet injection to reduce net erosion to zero everywhere if low-Z materials are used for the surface. Erosion rates can, in general, be minimized by large area limiters and high plasma temperatures, which transmit power to the walls with less sputtering. Under ideal steady state conditions the wall surface is dominated by metallurgical effects in the wall.

Energy Technology Data Exchange (ETDEWEB)

Means for increasing heat transfer characteristics between the surface of a solid and a boiling liquid are described in which the solid is immersed is comprised of a solid with passages which extend therethrough to the surface for the circulation of liquid through the passages for emergence from the surface to eliminate at least a portion of the unstable vapor film otherwise formed on the surface.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

DEFF Research Database (Denmark)

Udgivelsesdato: 2001-Mar

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

(Watkins and. Corbett,. 1964) which is a phosphorous-vacancy complex, i.e., ...... Grover. 1965. Semiconductor. Surfaces. ...

International Nuclear Information System (INIS)

Inorganic nanoparticles are indispensable for science and technology as materials, pigments and cosmetics products. Improving the dispersion stability of nanoparticles in various liquids is essential for those applications. In this review, we discuss why it is difficult to control the stability of nanoparticles in liquids. We also overview the role of surface interaction between nanoparticles in their dispersion and characterization, e.g. by colloid probe atomic force microscopy (CP-AFM). Two types of surface modification concepts, post-synthesis and in situ modification, were investigated in many previous studies. Here, we focus on post-synthesis modification using adsorption of various kinds of polymer dispersants and surfactants on the particle surface, as well as surface chemical reactions of silane coupling agents. We discuss CP-AFM as a technique to analyze the surface ...

Energy Technology Data Exchange (ETDEWEB)

This invention is an improved solar energy cavity receiver for exposing materials and components to high temperatures. The receiver includes a housing having an internal reflective surface defining a cavity and having an inlet for admitting solar radiation thereto. A photothermal absorber is positioned in the cavity to receive radiation from the inlet. A reflective baffle is positioned between the absorber and the inlet to severely restrict the re-radiation of energy through the inlet. The front surface of the baffle defines a narrow annulus with the internal reflective surface of the housing. The front surface of the baffle is contoured to reflect incoming radiation onto the internal surface of the housing, from which it is reflected through the annulus and onto the front surface of the absorber. The back surface of the baffle intercepts ...

British Library Electronic Table of Contents (United Kingdom)

In this paper, the effects of surface mediation on the adsorption isotherm and isosteric heat of adsorption on a graphite surface were investigated, as the surface mediation is known to affect the intermolecular interaction of adsorbed molecules close to the surface. Kim and Steele (Phys. Rev. B 45 (11) (1992) 6226-6233) and others have assumed that the surface mediation is confined only to the first layer. This will be tested in this paper with a combined experimental and Grand Canonical Monte Carlo (GCMC) simulation of adsorption of argon on graphitized thermal carbon black (GTCB) over a range of temperatures (77-95.25K). By matching the simulation results against the experimental data, we have found that the surface mediation is extended up to the fourth layer, rather than only the firs...

Energy Technology Data Exchange (ETDEWEB)

With an objective to learn reactivity of coal at its surface, surfaces of oxidized coal samples were investigated. Miike coal was oxidized by using {sup 18}O2 in a closed loop system. As the reaction progresses, proportion of CO2 including isotopes increased rapidly as a result of oxidation of CO sites existing in the coal and the newly generated C{sup 18}O sites. The oxidizing reaction progressed via oxygen adsorbing sites generated near the surface, and oxygen containing groups. An FT-IR analysis estimated the depth of the oxidized layer to be 10{mu}m or less from particle surface. The oxidized coal was pulverized to see its surface condition. Functional groups introduced by the oxidation enter into the vicinity of the surface in a form to desorb as CO. CO2 is trapped in inner pores. The coal surface was observed by using an atomic force ...

International Nuclear Information System (INIS)

Using the slow electrons spectrometer one can get information on the surface structure, its element composition, chemical bonds, adsorption phenomena, electron state density and surface oscillation. We have developed the methods and created the apparatus that makes it possible to investigate the electron backscattering by solid surface. We have studied the electron scattering by the polycrystalline and monocrystalline. GaAs surface in the energy range of 0 to 9 eV. The FWHM of electron energy distribution function was 70 meV. (author).

International Nuclear Information System (INIS)

Surface quality is one of the most important criteria for establishing the optimum cutting parameters needed to perform a machining process. Usually, the evaluation of the degree of the surface finishing requires to apply metrological techniques which involve times out in the production. As a consequence of this, a loss in both the economy of the process and the fiability of the tests reproducibility can be produced. In this work a relation between cutting force and surface roughness has been studied for the turning process of an Al-Cu alloy. From this relation, the surface quality of the machined samples can be evaluated by using the cutting forces values acquired during the cutting process. (Author) 8 refs.

International Nuclear Information System (INIS)

Calgary-based TAG Oil is an exploration company that manages 4.1 million acres of major producing oil and gas fields in New Zealand. The enormous Maui field, with 4 tcf of natural gas in place, has dominated the gas market in New Zealand by meeting nearly 90 per cent of the country's energy demand at costs much lower than world prices. However, the maturing field is in decline and will cease production by 2008. New gas field discoveries will only meet 60 per cent of the country's energy requirements for 5 additional years. Unless new large reserves of gas are discovered, the supply and demand situation will get worse. Lead time to place new production on-stream requires 5 to 10 years, which creates a large supply gap over the next decade. Public resistance to coal-fired power plants, new hydroelectric dams and nuclear power has left the country with no viable alternative to natural gas. TAG Oil has taken this unique opportunity to create value when gas demand is at ...

International Nuclear Information System (INIS)

In January 1994, a 6.7 magnitude earthquake in southern California ruptured a pipeline releasing approximately 4,200 barrels of blended San Joaquin Valley crude oil. A smaller volume entered the Santa Clara River and flowed 25 km downstream to an emergency containment dam. Ruptured water mains and chlorinated discharges from a damaged sewage treatment plant also affected water quality in the river. Quantitative injury assessment studies were initiated within days of the spill and included water/sediment chemistry, benthic macroinvertebrate community analyses and aquatic toxicity tests. Water quality values for TPH, BTEX, and chlorine ranged from nondetectable to 78 mg/l (TPH), nondetectable to 5.4 microg/l (total BTEX constituents) and nondetectable to 600 microg/l (residual chlorine) within 72 hours of the spill. Ammonia concentrations ranged from nondetectable to 12.1 mg/l within 10 days of the spill. Hydrocarbon concentrations in sediments ranged from ...

Energy Technology Data Exchange (ETDEWEB)

The dose-dependent transfer of [sup 203]Pb to milk and uptake in suckling rats and mice during a three-day nursing period was studied. On day 14 of lactation, the dams were administered a single intravenous dose of lead, labelled with [sup 203]Pb, in four or five doses from 0.0005 to 2.0 mg Pb/kg b.wt. There was a linear relationship between Pb levels in plasma and milk of both species. The Pb milk: plasma ratios at 24 hr after administration were 119 and 89 in mice and rats, respectively. At 72 hr the Pb milk: plasma ratio had decreased to 72 in mice and 35 in rats. The tissue levels of lead in the suckling rats and mice were also linearly correlated with lead concentration in milk at 72 hr, showing that milk could be used as an indicator of lead exposure to the suckling offspring. It is concluded that lead is transported into rat and mouse milk to a very high extent and the excretion into milk is more efficient in mice than in rats. On the other hand, rat pups ...

Science.gov (United States)

BACKGROUND: Denys-Drash Syndrome (DDS) is an uncommon disorder that appears sporadically and in rare cases may be inherited as an autosomal dominant trait It manifests either at birth or within the first year of life and typically consists of the triad of congenital nephropathy, Wilms tumour and intersex disorder. CASE REPORT: A 10 year-old Caucasian girl was referred to the Dental Department, at Glasgow Royal Hospital for Sick Children by her Paediatric Nephrologist Consultant. The patient was being teased by her peers over her markedly discoloured teeth. The dental history revealed that the patient was a regular dental attendee from an early age. She was dentally anxious having only experienced dental treatment under general anaesthesia (GA) when she was 4 years old. Apparently her primary dentition also showed a generalised discolouration. TREATMENT: This consisted of multiple visits for diet analysis and tooth brushing instruction with the use of disclosing tablets. Plaque control ...

Energy Technology Data Exchange (ETDEWEB)

Accelerated aging tests on tin-oxide-coated anodized aluminium selective absorber surfaces have been performed. It is shown that the tin oxide layer provides excellent protection for the anodized surface. The thermal stability of the double layer is equal to, or better than, the stability of the bare anodized surface. Both surfaces degrade very slowly at 450deg C. The anodic layer is porous and therefore not very scratch resistant and it degrades when exposed to humidity, both acidic and alcaline. It is shown that the tin oxide film, which is hard and chemically very stable, almost completely protects the anodized surface from chemical degradation. The mechanical wear resistance is also considerably improved. The optical selectivity does not quite match that of the the anodized surface, but the remarkable stability together with the solar parameters of ...

CERN Document Server

Surface compositional changes in GaAs due to RF plasmas of different gases have been investigated by XPS and etch rates were measured using AFM. Angular Resolved XPS (ARXPS) was also employed for depth analysis of the composition of the surface layers. An important role in this study was determination of oxide thickness using XPS data. The study of surface - plasma interaction was undertaken by correlating results of surface analysis with plasma diagnosis. Different experiments were designed to accurately measure the BEs associated with the Ga 3d, Ga 2p sub 3 sub / sub 2 and LMM peaks using XPS analysis and propose identification in terms of the oxides of GaAs. Along with GaAs wafers, some reference compounds such as metallic Ga and Ga sub 2 O sub 3 powder were used. A separate study aiming the identification of the GaAs surface oxides formed on the GaAs surface ...

International Nuclear Information System (INIS)

A comparative assessment of five different heat transfer configurations for operation in compact heat exchangers is presented. The configurations under consideration are four standaed heat exchanger surfaces - two plain fin, an offset strip and a louvered fin geometry - and one surface with so called vortex generators for heat transfer augmentation. In the case of the standard surfaces, the basic performance characteristics in the form of heat transfer and friction data versus the Reynolds number have been taken from published experimental results. In the case of the vortex generator surface, the performance characteristics have been derived from a numerical prediction of the flow and temperature field in a closely spaced parallel plate channel with vortex generators in the form of delta wings mounted on the channel walls. In comparison to the plain fin surfaces with a rectangular ...

International Nuclear Information System (INIS)

A self-consistent pseudopotential method together with a mixed-basis set of plane waves and Gaussian orbitals are used to determine the electronic structure of the (001) surface of molybdenum. The pseudopotential is derived from a self-consistent calculation of the atomic levels and wave functions, and is tested for bulk molybdenum. The resulting bulk band structure and density of states are compared with existing augmented-plane-wave APW calculations. The same potential is applied to investigate the electronic structure of an uncontracted Mo (001) surface. A complete analysis of the surface states is given in terms of their distribution in the two-dimensional surface Brillouin zone, charge-density distribution, and the local density of states. The results are in very good agreement with recent photoemission measurements.

Energy Technology Data Exchange (ETDEWEB)

A method for preparing metal for heating by infrared radiance to enable uniform and consistent heating. The surface of one or more metal parts, such as aluminum or aluminum alloy parts, is treated to alter the surface finish to affect the reflectivity of the surface. The surface reflectivity is evaluated, such as by taking measurements at one or more points on the surface, to determine if a desired reflectivity has been achieved. The treating and measuring are performed until the measuring indicates that the desired reflectivity has been achieved. Once the treating has altered the surface finish to achieve the desired reflectivity, the metal part may then be exposed to infrared radiance to heat the metal part to a desired temperature, and that heating will be substantially consistent throughout by virtue of the desired reflectivity.

International Nuclear Information System (INIS)

Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a tool for the ...

Energy Technology Data Exchange (ETDEWEB)

A new technique for ion implantation into concave surface of insulating materials is proposed and experimentally studied. The principle is roughly described by referring to modifying inner surface of a PET (polyethylene terephthalate) bottle. An electrode that is supplied with positive high-voltage pulses is inserted into the bottle. Both plasma formation and ion implantation are simultaneously realized by the same high-voltage pulses. Ion sheath with a certain thickness that depends on plasma parameters is formed just on the inner surface of the bottle. Since the plasma potential is very close to that of the electrode, ions from the plasma are accelerated in the sheath and implanted perpendicularly into the bottle's inner surface. Laser Raman spectroscopy shows that the inner surface of an ion-implanted PET bottle is modified into DLC (diamond-like carbon). Gas permeation ...

British Library Electronic Table of Contents (United Kingdom)

This paper deals with surface defects of automobile outer panels, which alter significantly the vehicle quality. Such defects occur during springback, after forming or flanging steps, and are characterized by concave depression of small amplitude over the convex shape of the part. The aim of this work is to reproduce at the laboratory scale a surface defect that occurs after flanging on a geometry similar to a door upper corner. A dedicated device has been designed in order to generate small size surface defects during flanging of metallic thin sheets. The outer surface of the sample was digitalized and the spatial geometry of the defect was evaluated from curvature change along 2D profiles. This study shows that the flanging height does not influence significantly the surface defect geome...

Energy Technology Data Exchange (ETDEWEB)

A simple model based on surface chemistry is developed, based an simple concepts of contact angle, wetting and spreading. Results of the modeling can be stated by two simplified rules of thumb'': (1) A liquid will spread on the surface of a solid if the surface tension of the liquid is lose than the surface free energy of the solid, and (2) The liquid having the surface tension nearest that of the solid will preferentially wet the surface of the solid. These two rules can then be used to define the parameters that constitute a process for formulating a plastic bonded explosive (PBX), which is a crystalline high-explosive material coated with a small amount of plastic polymeric material (the binder). The PBX then can be pressed to a high density, and machined to a specific shape. The pressed and machined explosive material can then be used in a ...

British Library Electronic Table of Contents (United Kingdom)

WC-Co hardmetals with gradient structure comprising neither -phase nor grain growth inhibitors were produced for the first time by regulating the WC re-crystallisation and carbon content in their near-surface layer and core. Hardmetals with low Co contents in the surface region were obtained by selective carburisation of the near-surface zone of green articles with the original low carbon content and their consequent liquid-phase sintering. The surface region of such gradient hardmetals has a hardness of up 150 Vickers units higher and fracture toughness significantly superior than those of the core. Gradient hardmetals with high Co contents in the surface region were obtained by selective decarburisation of the near-surface zone of green articles with the original high carbon content and ...

Science.gov (United States)

We model nongraphitized carbon black surfaces and investigate adsorption of argon on these surfaces by using the grand canonical Monte Carlo simulation. In this model, the nongraphitized surface is modeled as a stack of graphene layers with some carbon atoms of the top graphene layer being randomly removed. The percentage of the surface carbon atoms being removed and the effective size of the defect (created by the removal) are the key parameters to characterize the nongraphitized surface. The patterns of adsorption isotherm and isosteric heat are particularly studied, as a function of these surface parameters as well as pressure and temperature. It is shown that the adsorption isotherm shows a steplike behavior on a perfect graphite surface and becomes smoother on nongraphitized surfaces. Regarding the isosteric heat ...

International Nuclear Information System (INIS)

Water repellency en the microstructure super-hydrophobic cured surface is important for research and industrial purposes. This microstructure film can be cured on polyethylene terephthalate PET surface by electron beam (EB) at different irradiation doses 10-100 kGy. The microstructure formulation composed from hydrophobic acrylate oligomer (EB 244) and monomer (SR 440). The irradiation induced cross linking of the prepared microstructure was proved by FTIR spectroscopy and the adhesion force by abrasion test. Some factors affecting the adhesion force of the prepared microstructure film such as oligomer/monomer composition ratio and the thickness of the microstructure cured film were studied. The contact angles (8) were measured on cured surfaces before and after adding the super hydrophobic nanoparticles (Zonyl 9361). The super-hydrophobic cured surface showed the self-cleaning property. The volume of ...

Science.gov (United States)

In this activity, students create two- and three-dimensional maps by using a data grid of an imaginary section of Earth's surface. They are challenged to create six different maps of various surface features and answer questions about them.

Energy Technology Data Exchange (ETDEWEB)

The behavior and properties of associated bodies were studied through measurement of surface tension considering acetone-soluble fraction relatively light among various solvent extracts of coal. In experiment, the acetone-soluble fraction was extracted from the substances extracted from Upper Freeport coal as standard specimen using the mixed solvent of carbon disulfide (CS2) and N-methyl-2-pyrrolidinone (NMP), and it was dissolved into NMP after drying. Surface tension was measured by Wilhelmy method. The experimental results are as follows. Equilibrium surface tension is equal to the surface tension of pure solvent in a low concentration range of solution, and decreases with an increase in concentration approaching a fixed value at 0 in log concentration, nearly showing an S curve. Adsorption of species with non-polar aromatic ring of the acetone-soluble fraction on a solution ...

International Nuclear Information System (INIS)

This section of the report is concerned with the study of the metallisation, oxidation and doping of materials which are of importance to the micro-electronics industry. The Van de Graaff accelerator and radioactive tracers are used for studying surface and sub-surface behaviour of these materials.

International Nuclear Information System (INIS)

A survey is given of the influence of surface deformations on heavy ion reactions. Emphasis is put on the effect of zeropoint fluctuations in the entrance channel and on the effect on grazing collisions in terms of an imaginary part of the scattering potential. (orig.).

International Nuclear Information System (INIS)

Plasma nitriding in glow discharge is a process of modifying surface properties of a material by which surface hardness, corrosion resistance, fatigue strength etc. of a material can be improved

UK PubMed Central (United Kingdom)

BackgroundThe expression of human virus surface proteins, as well as other mammalian glycoproteins, is much more efficient in cells of higher eukaryotes rather than yeasts. The limitations...Full Text Available

UK PubMed Central (United Kingdom)

We have developed miniature (≈1 μm diameter) microcavity surface-plasmon-resonance sensors (MSPRS), integrated them with microfluidics and tested...Full Text Available

International Nuclear Information System (INIS)

The methods of surface modification of Ti-Zr alloy by laser treatment are considered. Characteristics of laser modification without- and with surface melting and with melting in different gaseous environments and with nickel microalloying are presented. Maximum depth, hardness and corrosion resistance are observed under nickel laser alloying.

UK PubMed Central (United Kingdom)

The interior of 237 nm spherical vinylsilsesquioxane nanoparticles has been covalently modified and their surface functionalized under mild conditions to yield a novel type of hybrid silsesquioxane...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Industrial applications of thermoplastic polymers are often limited by their poor adhesion properties. In this work the effect of surface oxyfluorination on the adhesion properties was investigated for polyethylene (PE), polyoxymethylene (POM), polybutylene terephthalate (PBT) and polyamide 6 (PA6). The adhesive joint strength was quantified using lap-shear tests. These results were correlated with the changes in the chemical composition of the surface, determined by X-ray photoelectron spectroscopy (XPS), in the surface free energy, measured by the contact angle method, and in the topography, using white-light confocal microscopy. The adhesive strength is strongly improved for all four polymers, but the degree of this increase depends on the polymer type. The surface free energy shows a similar trend for all four polymers. A high surface free energy exceeding 50 mN/m was observed ...

UK PubMed Central (United Kingdom)

It has been postulated that thrombin binds to endothelial cells through, at least in part, cell surface glycosaminoglycans such as heparan sulfate, which could serve as antithrombin cofactor on the...Full Text Available

UK PubMed Central (United Kingdom)

Plant surfaces covered with crystalline epicuticular waxes are known to be anti-adhesive, hardly wettable and preventing insect attachment. But there are insects that are capable of gluing their eggs...Full Text Available

UK PubMed Central (United Kingdom)

We study how the microscale topography of a solid surface affects the apparent advancing and receding angles at the contact line of a liquid drop pinned to this surface. Photolithographic methods...Full Text Available

UK PubMed Central (United Kingdom)

The opportunistic pathogenic yeast Candida albicans exhibits growth phase-dependent changes in cell surface hydrophobicity, which has been correlated with adhesion to host tissues....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this paper the authors prove a uniqueness theorem for the electric detection of cavities in a three dimensional solid from Cauchy data measured on the surface. The cavities, finite in number, are assumed to be insulating. The surfaces of the cavities are assumed to be smooth on the complement of a set that is, in some sense, negligible. (orig.)

UK PubMed Central (United Kingdom)

Functionalizing of single molecules on surfaces has manifested great potential for bottom-up construction of complex devices on a molecular scale. We discuss the growth mechanism for the initial layers...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Ultrasonic enhancement of heat transfer on a narrow surface was measured by changing the width of the surface from 8 to 0.1 mm. Ultrasonic power of 600 W with a frequency of 40 kHz was used. Heat transfer on the narrow surface without ultrasonic vibration was correlated by the experimental equation for a thin wire. The cavitation intensity was measured by the cavitation erosion loss of an aluminum foil of 15 [mu]m thickness. The effects of acoustic streaming and cavitation were separated by this measurement. Heat transfer by acoustic streaming was predicted through forced convection. Enhancement by cavitation was explained by the turbulence thermal conductivity of the microjets.

Energy Technology Data Exchange (ETDEWEB)

A high pressure waterjet has been used to study the surface roughening of superalloys as preparation for thermal spraying. Designed experiments for Mar-M 509 and Rene 80 were carried out for the effects of jet pressure and mass of water delivered per unit area. Comparisons were made of several superalloys in terms of erosion, surface roughness and topology. The mechanism of jet erosion of Rene 80 was studied in relation to its metallurgical microstructure. An MCrAlY coating by shrouded plasma spray was made over a waterjet prepared surface with excellent bonding and having an ideally clean interface.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Abstract : The acousto-optic filter (AOF) is ... for large switch networks. ... FOURIER TRANSFORMATION, OPTICAL SWITCHING, SURFACE ACOUSTIC ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... interactive surfaces and interfaces, and 3) the more complex a ... carbonate or calcium phosphate with a thin interface ... diameter) for nerve prosthesis. ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We present a numerical method for computing diffusive transport on a surface derived from image data. Our underlying discretization method uses a Cartesian grid embedded boundary method for computing the volume transport in region consisting of all points a small distance from the surface. We obtain a representation of this region from image data using a front propagation computation based on level set methods for solving the Hamilton-Jacobi and eikonal equations. We demonstrate that the method is second-order accurate in space and time, and is capable of computing solutions on complex surface geometries obtained from image data of cells.

International Nuclear Information System (INIS)

Nano-materials in which a large fraction of atoms resides within a few atomic layers near the surface can be designed to have novel properties by manipulating their surface parameters. We show that the effective elastic constants of nano-porous/cellular materials can be made to exceed those of the parent materials provided the pore surface elastic parameters satisfy certain conditions. These stiff nano-porous materials herald a radical breakthrough in sandwich-type construction.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The surface composition and composition near the surface and properties of high-silica zeolites of the TsVK-1 type were studied by XPES, IRS, and low-temperature adsorption of N/sub 2/. It was found that changing the sequence of operations during preparation of the H form of the zeolites results in a different set of acid centers on their surface, caused by migration of cations into the bulk of the zeolites. Migration of elements is also observed during the catalytic reaction of conversion of ethanol.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... solid particle contamination. Solid particulate impact is a good mechanism for surface heat transfer augmentation. The aug ...

Energy Technology Data Exchange (ETDEWEB)

The state of lithium electrode surface after contact with triethylamine-modified propylene carbonate solutions of lithium perchlorate was studied using the pulse galvanostatic technique as well as methods of SIMS and electron microscopy. It was shown that amine added into the solutions stabilizes the state of lithium and prevents the formation of a secondary porous passive film on the lithium surface. Chemical composition of the primary film remains unchanged. Certain properties of passive films formed in electrolyte solutions studied were evaluated.

Energy Technology Data Exchange (ETDEWEB)

Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are though to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.

International Nuclear Information System (INIS)

Full text: The surface properties of poly (tetrafluoroethylene) (PTFE) are changed by the exposure to synchrotron radiation (SR). We succeeded in controlling the wettability of the PTFE surface from hydrophobic to hydrophilic by varying the substrate temperature during the SR irradiation and found that the wettability was ascribable to microstructure and chemical composition of surface.In these previous works, oxygen atoms were found to inhabit on the hydrophobic surface of PTFE. In this study, we investigated the surface modification of PTFE from the SR exposure experiment under the O_2 gas atmosphere. The SR exposure to the PTFE sheet was carried out at beamline 6 (BL6) of the New- SUBARU. The PTFE sheet was irradiated to the white beam, ranging 50-1000 eV at BL6 at room temperature. The gas cell was mounted at the irradiation chamber. The O_2 gas pressure in the gas cell can be ...

Energy Technology Data Exchange (ETDEWEB)

Reflective diffraction grating. A focused ion beam (FIB) micromilling apparatus is used to store color images in a durable medium by milling away portions of the surface of the medium to produce a reflective diffraction grating with blazed pits. The images are retrieved by exposing the surface of the grating to polychromatic light from a particular incident bearing and observing the light reflected by the surface from specified reception bearing.

Energy Technology Data Exchange (ETDEWEB)

We propose a generalization of the character formulas of the SU(2) Kac-Moody algebra to higher genus Riemann surfaces. With this construction, we show that the modular invariant partition funciton of the SO(4) k = 1 Wess-Zumino model is equivalent, in arbitrary genus Riemann surfaces, to that of free fermion theory.

Energy Technology Data Exchange (ETDEWEB)

Climates at regional scale are strongly dependent on the interaction between atmosphere and its lower boundary, the oceans and the land surface mosaic. Land surfaces influence climate through their albedo, and the aerodynamic roughness, the processes of the biosphere and many soil hydrological properties; all these factors vary considerably geographically. Land surfaces receive a certain portion of the solar irradiance depending on the cloudiness, atmospheric transparency and surface albedo. Short-wave solar irradiance is the source of the heat energy exchange at the earth`s surface and also regulates many biological processes, e.g. photosynthesis. Methods for estimating solar irradiance, atmospheric transparency and surface albedo were reviewed during the course of this project. The solar energy at earth`s surface is consumed for heating ...

International Nuclear Information System (INIS)

The IGC-30 HPGe detector with MCA 'CANBERRA-10 PLUS' allows to determine surface contamination of areas of any type with a minimum error in radius 8-10 m, at a 'uniform' contamination. A modification of the CANBERRA hardware and software is described allowing determination of both the activity of a possible 'radioactive spot' and the activity of the whole observed surface. (author).

Energy Technology Data Exchange (ETDEWEB)

The fundamental ionisation process of negative surface ionisation is described and two applications are discussed. One is in the so called surface-plasma sources which enable the production of intense negative ion beams. The second application is in the passive diagnosis of the charge exchange of neutrals emitted from hydrogen plasmas.

Energy Technology Data Exchange (ETDEWEB)

A spherical-geometry, self-extraction negative ion source has been designed and fabricated. The source utilizes direct surface ionization to form negative ion beams resulting from interactions between high electron affinity gaseous elemental or molecular materials and a negatively biased, spherical-sector LaB{sub 6} surface ionizer maintained at {similar to}1300 K. The design features of this source and principles upon which the source is based are discussed in this report.

British Library Electronic Table of Contents (United Kingdom)

A mission to the surface of Venus would have high scientific value, but most electronic devices and sensors cannot operate at the 450degreeC ambient surface temperature of Venus. Power and cooling systems were analyzed for Venus surface operation. A radioisotope power and cooling system was designed to provide electrical power for a probe operating on the surface of Venus. For a mission duration of substantial length, the use of thermal mass to maintain an operable temperature range is likely impractical, and active refrigeration may be required to keep components at a temperature below ambient. Due to the high thermal convection of the high-density atmosphere, the heat rejection temperature was assumed to be at a 500degreeC radiator temperature, 50degreeC above ambient. The radioisotope S...

British Library Electronic Table of Contents (United Kingdom)

Plastic injection molds are an important economic sector due to the increasing use of injection molded plastic components. The selection of mold steel material, its processing conditions, and the way it is machined and hardened all have an impact on how it performs during use across its lifecycle for injection molding. For this study, injection molding conditions seen during high volume manufacturing were used to induce wear that would be typical during processing. A 50wt.% glass fiber reinforced Polybutylene Terephthalate (PBT) was used for the research. After 3000 injection operations, surface damage was found only on the steel used for the stationary half of the mold cavity and the corresponding surface of the molded parts. In contrast, the moving half showed no surface damage or increa...

International Nuclear Information System (INIS)

Soil placed over any sealant/barrier system can provide a protective mantle if the soil is not lost by erosion. Vegetation is an attractive choice for controlling erosion because it can provide an economic self-renewing cover that serves to reduce erosion by both wind and water. Vegetation alone, however, may not adequately stabilize the surface in extremely arid areas. In those areas, a properly designed surface treatment of rock cover, perhaps in conjunction with vegetation, may be necessary to stabilize the tailings surfaces. The objective of this program is to establish guidelines for surface stabilization that are compatible with sealant/barrier systems and that are suited to soils and climates at inactive uranium mill tailings sites. These guidelines will provide the means to estimate potential vegetation cover, potential erosion, effects of surface treatments on ...

British Library Electronic Table of Contents (United Kingdom)

We investigated the use of Surface Free Energy (SFE) measurements, describing coherence between surfaces of two solids, in evaluation of affinity between skin surface and foundation, a possible predictor of makeup longevity. We found that the gp values of skin varied significantly among subjects. After discovering that the SFE values of most available conventional foundation products were very different from that of skin, specially formulated experimental foundations with SFE values close to that of the skin surface were prepared using conventional powder ingredients and novel powder ingredients coated with polyethylene glycol. In our usage tests, the SFE-controlled foundations demonstrated superior performance to that of conventional foundations and most of subjects preferred the SFE-cont...

CERN Document Server

The confining effect of a spherical substrate inducing anchoring (normal to the surface) of rod-like liquid crystal molecules contained in a thin film spread over it has been investigated with regard to possible changes in the nature of the isotropic-to-nematic phase transition as the sample is cooled. The focus of these Monte Carlo simulations is to study the competing effects of the homeotropic anchoring due to the surface inducing orientational ordering in the radial direction and the inherent uniaxial order promoted by the intermolecular interactions. By adopting entropic sampling procedure, we could investigate this transition with a high temperature precision, and we studied the effect of the surface anchoring strength on the phase diagram for a specifically chosen geometry. We find that there is a threshold anchoring strength of the surface below which uniaxial nematic phase results, and above ...

International Nuclear Information System (INIS)

A Gross Decontamination Experiment was conducted on various levels and surfaces of the TMI - Unit 2 reactor building in March 1982. The polar crane, D-rings, missile shields, refueling canals, refueling bridges, equipment, and elevations 305' and 347'-6'' were flushed with low pressure water. Additionally, floor surfaces on elevation 305' and floor surfaces and major pieces of equipment on elevation 347'-6'' were sprayed with high pressure water. Selective surfaces were decontaminated with a mechanical scrubber and chemicals. Strippable coating was tested and evaluated on equipment and floor surfaces. The effectiveness, efficiency, and safety of several decontamination techniques were established for the large, complex decontamination effort. Various decontamination equipment was evaluated and its effectiveness was documented. Decontamination training and procedures were documented ...

Energy Technology Data Exchange (ETDEWEB)

The use of dendrimers for preparing chemically sensitive interfaces for detecting volatile organic compounds (VOCs) using surface acoustic wave (SAW) device transducers is described. Specifically, the synthesis of the dendrimers and the means by which they are affixed to SAW devices is discussed, followed by a detailed spectroscopic analysis of the surface-confined dendrimers and a discussion of their interaction with different VOCs. Most of these preliminary experiments focus on dendrimer surface modification using benzoylchloride, which leads to phenyl terminal groups linked to the dendrimer via amide groups. The results of this study lead us to conclude that dendrimers: (1) provide general specificity towards classes of functional groups and are therefore suitable for array-based sensing schemes; (2) are intermediate in structure between monolayers and polymers and exhibit the desirable properties of both; (3) can be ...

Energy Technology Data Exchange (ETDEWEB)

Experiments on the depth dependence of transient enhanced diffusion (TED) of boron during rapid thermal annealing of Ge-preamorphized layers reveal a linear decrease in the diffusion enhancement between the end-of-range (EOR) defect band and the surface. This behavior, which indicates a quasi-steady-state distribution of excess interstitials, emitted from the EOR band and absorbed at the surface, is observed for annealing times as short as 1 s at 900 deg. C. Using an etching procedure we vary the distance x{sub EOR} from the EOR band to the surface in the range 80-175 nm, and observe how this influences the interstitial supersaturation, s(x). The supersaturations at the EOR band and the surface remain unchanged, while the gradient ds/dx, and thus the flux to the surface, varies inversely with x{sub EOR}. This confirms the validity of earlier modelling of EOR defect evolution in ...

International Nuclear Information System (INIS)

An outline is given of time-dependent wavepacket methods as applied to calculations of molecular collisions with solid surfaces. The methods reviewed include numerical integration algorithms for the time-dependent Schroedinger equation, semiclassical wavepacket treatments, and approximations that treat some of the degrees-of-freedom quantum-mechanically and others classically. The computational and numerical characteristics of these methods are discussed, with emphasis on their particular advantages and relevance in the context of certain molecule/surface scattering problems. For the semiclassical and mixed quantal-classical treatments, the approximation errors and their physical origins are discussed. For the quantum wavepacket techniques a numerical error analysis is presented. The computational efficiency of the various algorithms is considered and examined in the context of several applications. The main focus is on diffractive scattering ...

International Nuclear Information System (INIS)

By using a plasma nitriding procedure at the PUPR Mirror Cusp Plasma machine, surface hardness is increased in 302/304-type stainless steel samples by exposing them to high-ion-density plasma at high vacuum. This method successfully dopes the surface of the material with strengthening nitrogen ions, without the use of chemical procedures that sacrifice the resistance to corrosion of the given material. A 500 V negative bias is placed on the sample exposed to the nitrogen plasma, where high-energy ions are therefore attracted and immersed into the metallic matrix microns into the surface of the stainless steel. This potential maintains a constant surface temperature at approximately 800 deg. C. The plasma parameters including ion density and plasma temperature were diagnosed using single Langmuir probes. The stainless steel samples were then tested using scanning electron microscopy (SEM), and Vickers ...

Energy Technology Data Exchange (ETDEWEB)

The surface enhanced Raman scattering (SERS) spectra of piperidine in silver colloid solution, on roughened silver electrode and on roughened silver electrode modified with silver nanoparticles were studied, and the high-quality SERS spectra of piperidine on roughened silver electrode modified with silver nanoparticles were obtained for the first time. Surface selection rules derived from the EM enhancement model were employed to deduce piperidine orientations on the different surfaces. On the basis of this, two models of piperidine adsorbed on the surface of the silver nanoparticles were built, and DFT-B3PW91/LanL2dz was applied to calculate the Raman frequencies. It proves that, at higher potential values, the piperidine is perpendicularly standing on the roughened silver electrode surface though its lone-electron pair, but in silver colloid solution and on the silver ...

International Nuclear Information System (INIS)

The possibility of smoothening aspherical X-ray mirrors by irradiation of the surface with a low-energy ion beam is investigated. Nanofocusing being the primary application of these mirrors the ion beam conditions must be optimized to achieve a surface roughness of the order of 0.1-0.2 nm. To address this issue a first study was performed on silicon flat substrates etched using ion energies ranging from 400 to 1200 eV. A second study consisted of eroding the silicon surface while varying the ion grazing incidence angle between 10 deg. and 90 deg. for a fixed value of the ion energy. The surface topography of the samples was characterized at various scales using atomic force microscopy (probed area: 1-10 ?m2), interferential optical microscopy (probed area: 1 mm2) and X-ray scattering (probed area: 100 mm2). Finally, a study by AFM of the evolution of the surface finish level of a ...

Science.gov (United States)

Near-ideal Schottky barrier contacts to n-type Al0.22Ga0.78N have been developed by a two-step surface treatment technique. Plasma etching of the AlxGa1-xN surface prior to Schottky metal deposition, combined with sequential chemical treatment of the etched surface, holds promise for developing high quality low-leakage Schottky contacts for low noise applications and for recessed gate high electron mobility transistors. In this work, the effect of postetch chemical treatment of the n-type Al0.22Ga0.78N surface on the performance of the Ni/Au based Schottky contact has been investigated. Three different types of chemical treatment: viz, reactive ion etching, reactive ion etching plus dipping in hot aqua regia, and reactive ion etching plus dipping in hot KOH, are studied. Detailed current-voltage studies of three different surface treated diodes and a comparison with as-deposited ...

Energy Technology Data Exchange (ETDEWEB)

Micropatterned surfaces with different chemical topographies were synthesised in order to investigate the influence of surface chemistry and topography on cell behaviour. The microstructured materials were synthesised by photoimmobilising natural Hyaluronan (Hyal) and its sulphated derivative (HyalS), both adequately functionalised with a photorective moiety, on glass substrates. Four different grating patterns (10, 25, 50 and 100 {mu}m) were used to pattern the hyaluronan. The micropatterned samples were analysed by Secondary Ions Mass Spectrometry, Scanning Electron Microscopy (SEM) and Atomic Force Microscopy to investigate the chemistry and the topography of the surfaces. The spectroscopic and microscopic analysis of the microstructured surfaces revealed that the photoimmobilisation process was successful, demonstrating that the photomask patterns were well reproduced on the sample ...

Energy Technology Data Exchange (ETDEWEB)

The principle aim of the program was to produce a novel, non-leaching antimicrobial surface for commercial development and future use in the liquid food packaging industry. Antimicrobial surfaces which exist presently have been produced to combat the growth of prokaryotic organisms and usually function as slow release systems. A system which could inhibit eukaryotic growth without contaminating the surrounding 'environment' with the inhibitor was considered of great commercial importance. The remit of this study was concerned with creating a surface which could control the growth of eukaryotic organisms found in fruit juice with particular interest in the yeast, Saccharomyces cerevisiae. Putative antimicrobial surfaces were created by the chemical modification of the test substrate polymers; nylon and ethylvinyl alcohol (EVOH). Surfaces were chemically modified by ...

Energy Technology Data Exchange (ETDEWEB)

A number of properties in steel components are detrimentally influenced when exposed to hydrogen environments. Under these conditions, atomic hydrogen is adsorbed on the steel surface, then absorbed and preferentially transported towards tri-dimensional stressed regions in the crystal lattice and into defects such as interfaces or dislocations. The hydrogen embrittlement susceptibility is strongly influenced by various microstructural parameters including the type of inclusions, steel composition and heat treating conditions. One of the alternatives employed in minimizing hydrogen embrittlement is the use of surface barriers for hydrogen permeation. In particular, the presence of surface nitride layers in steels can be considered as an effective barrier. Nitride steel surface layers can be produced by plasma nitriding with the concomitant benefits of improved surface hardness, as ...

Energy Technology Data Exchange (ETDEWEB)

In addition to ceramics, alloys such as tool steel and nickel- and iron-based superalloys are being considered for high temperature applications such as missile bearings and low heat rejection engines. Studies were made to lubricate a nickel-based superalloy at 500{degrees}C, by using a vaporized aryl phosphate ester, at a concentration of 0.1% in air. From deposition and wear studies it was found that it was impossible to form a good polymeric coating on the superalloy surface. Energy dispersive X-ray analyzer (EDXA) analysis showed that this was due to minute quantities of aluminum in the alloy segregating to the surface, upon being heated to 500{degrees}C, forming a passive oxide coating. It was necessary to activate the surface, in order to lubricate the material successfully. A method of activation by electrodepositing the surface with a layer of iron oxide was developed. Once activated, a good ...

Science.gov (United States)

The contents of this report covers: (1) development of optimal geometries for crowned helical gears; (2) a method for their generation; (3) tooth contact analysis (TCA) computer programs for the analysis of meshing and bearing contact of the crowned helical gears; and (4) modelling and simulation of gear shaft deflection. The developed method for synthesis was used to determine the optimal geometry for a crowned helical pinion surface and was directed to localize the bearing contact and guarantee favorable shape and a low level of transmission errors. Two new methods for generation of the crowned helical pinion surface are proposed. One is based on the application of a tool with a surface of revolution that slightly deviates from a regular cone surface. The tool can be used as a grinding wheel or as a shaver. The other is based on a crowning pinion tooth surface with predesigned ...

Energy Technology Data Exchange (ETDEWEB)

The relationship between the gas to melt ratio (GMR) and the surface temperature of an evolving billet surface in spray forming is investigated numerically. The basis for the analysis is an integrated approach for modelling the entire spray forming process. This model includes the droplet atomization taking thermal coupling into consideration and the deposition of material at the surface of the billet taking geometrical aspects such as shading into account. The coupling between these two models is accomplished by ensuring that the total droplet size distribution of the spray is the summation of ''local'' droplet size distributions along the r-axis of the spray cone. The criterion for a successful process has been a predefined process window characterised by a desired fraction solid range at a certain distance from the atomizer. Inside this process window, the gas and melt flows have been ...

Energy Technology Data Exchange (ETDEWEB)

Mechanisms that govern transport, accumulation and toxicity of persistent pollutants at interfaces in aquatic ecosystems were the foci of this thesis. Specific attention was paid to humic substances, their occurrence, composition, and role in exchange processes across interfaces. It was concluded that: The composition of humic substances in aquatic surface microlayers is different from that of the subsurface water and terrestrial humic matter. Levels of dissolved organic carbon (DOC) in the aquatic surface microlayer reflect the DOC levels in the subsurface water. While the levels and enrichment of DOC in the microlayer generally show small variations, the levels and enrichment of particulate organic carbon (POC) vary to a great extent. Similarities exist between aquatic surface films, artificial semi-permeable and biological membranes regarding their structure and functioning. Acidification and liming of freshwater ...

International Nuclear Information System (INIS)

Samples prepared using the focused ion beam (FIB) inevitably contain the surface damage induced by energetic Ga"+ ions. An effective method of removing the surface damage is demonstrated using a plasma cleaner, a device which is widely used to minimize the surface contamination in scanning transmission electron microscopy (STEM). Surface bombardment with low-energy Ar"+ ions was induced by biasing the sample immersed in the plasma source, so as to etch off the surface materials. The etch rates of SiO_2, measured with a bias voltage of 100-300 V, were found to vary linearly with both the time and bias and were able to be controlled from 1.4 to 9 nm/min. The removal of the Ga residue was confirmed using energy dispersive spectroscopy (EDS) after the plasma processing of the FIB-prepared sample. When the FIB-prepared sample was processed via plasma etching for 10 min with a bias of 150 ...

International Nuclear Information System (INIS)

Kinetic Monte Carlo simulations are used to analyze the ripening and dissolution of small Si interstitial clusters and #left brace#113#right brace# defects, and its influence on transient enhanced diffusion of dopants in silicon. The evolution of Si interstitial defects is studied in terms of the probabilities of emitted Si interstitials being recaptured by other defects or in turn being annihilated at the surface. These two probabilities are related to the average distance among defects and their distance to the surface, respectively. During the initial stages of the defect ripening, when the defect concentration is high enough and the distance among them is small, Si interstitials are mostly exchanged among defects with a minimal loss of them to the surface. Only when defects grow to large sizes and their concentration decreases, the loss of Si interstitials through diffusion to the surface prevails, ...

Energy Technology Data Exchange (ETDEWEB)

The atmosphere and the biosphere are inherently coupled to one another. Atmospheric surface state variables such as temperature, winds, water vapor, precipitation, and radiation control biophysical, biogeochemical, and ecological processes at the surface and subsurface. At the same time, surface fluxes of momentum, moisture, heat, and trace gases act as time-dependent boundary conditions providing feedback on atmospheric processes. To understand such phenomena, a coupled set of interactive models is required. Costs are still prohibitive for computing surface/subsurface fluxes directly for medium-resolution atmospheric general circulation models (AGCMs), but a technique has been developed for testing large-scale homogeneity and accessing surface parameterizations and models to reduce this computational cost and maintain accuracy. This modeling system potentially bridges the observed ...

International Nuclear Information System (INIS)

A series of ball-on-disc wear and friction measurements were made for surfaces which have a chemical vapour deposition carbon silicon alloy layer on a carbon substrate (fine grain POCO graphite). Nitrogen ion irradiation was used to improve the wear resistance of the carbon alloy surface. For comparison, measurements were also taken for alumina against alumina. It was found that the lowest friction coefficient and lowest wear occurred for ion irradiated coated samples containing 4% Si in the alloy and that the performance was superior to that of alumina. ((orig.)).

Energy Technology Data Exchange (ETDEWEB)

The properties of a helium film on the surface of solid parahydrogen are investigated. It is shown that wetting of the solid hydrogen by the liquid helium occurs. The transport velocities along the He II film on the solid parahydrogen surface are measured in broad temperature, film height, and level difference ranges. It is shown that the transport velocity in this case has the least value as compared with its value on other substrates. The thickness of the helium-saturated film is determined on the solid hydrogen surface on the basis of the data obtained, and the value is in good agreement with the results of a computation performed within the framework of the Frenkel' theory.

International Nuclear Information System (INIS)

The early work of Stern has been reviewed briefly along with some of our experiments carried out later with similar geometrical arrangements in order to highlight his successes at the time and the future developments of his findings and predictions. The double crystal technique, developed by Stern has been used for energy analysis of He beams and results are shown for scattering from a rough reconstructed (001) InSb surface and Xe adsorbed layers. Surface phonons were not observed in the case of InSb probably as a result of the rough surface. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The chemical properties of alloys in a given environment are to a large extent governed by the surface composition. Changes of the surface composition during passivation are important features in this respect. Previous studies of single crystal Ni-Mo alloys surfaces have been reported. The aim of this work was to obtain quantitative data, for the natural oxide and the passive films formed on Ni-6% Mo(100) and (110) alloys, using Rutherford backscattering spectroscopy and nuclear reaction analysis.

Energy Technology Data Exchange (ETDEWEB)

The applications of neutron reflectometry to study dynamic phenomena at surface and interfaces have been restricted so far. This was mainly due to the low intensity of neutron sources, but now high-intensity spallation neutron sources are under construction in Japan (J-PARC) and US (SNS). We are planning to install a spin-echo option on the J-PARC neutron reflectometer with horizontal sample geometry for studies of dynamics of surfaces and interfaces. This option is based on the resonance spin-echo method and aimed at dynamics up to hundreds of nanoseconds. In this contribution, the plan and status of development are introduced together with the principle and characteristics of this option.

Energy Technology Data Exchange (ETDEWEB)

Preliminary results of studies into penetrant testing at high surface temperature (up to 200 deg.C), are presented. Tests were performed to assess the effectiveness of red dye penetrants using Al and NiCr samples containing artificial as well as natural discontinuities. The test results will be used in due course to formulate a specification for non-destructive testing procedure qualification at non-standard (i.e. outside 16-52 deg.C) temperatures.

Energy Technology Data Exchange (ETDEWEB)

In situ Auger sputter depth profiles of saturation implants of 3 keV N/sub 2//sup +/ in silicon at room temperature exhibit a sharp peak in the nitrogen concentration in the outermost layers, followed by a monotonic decrease. No broad plateau was observed. The energy of the Auger line corresponding to the Si(2p) core electron excitation, monitored throughout the profiling, exhibits a chemical shift of up to 7 eV at the surface peak concentration. Inert gas ion post-bombardment of unsaturated implants significantly modifies the profile, and supports the suggestion that the surface peak arises through radiation enhanced diffusion of implanted atoms.

Energy Technology Data Exchange (ETDEWEB)

Silicon nitride hybrid ball bearings used in high temperature applications undergo mechanical and environmental degradation. To study the surface chemistry of silicon nitride, a CAChe{trademark} Worksystem* has been used to generate the clusters and corresponding transmission vibrational spectra of silicon nitride. In the present study, the effect of surface conditions on the surface chemistry and wear degradation of silicon nitride was evaluated. Infrared reflection spectroscopy (IRRS) used to determine molecular orientations shows a difference in reflectance spectra for fractured and as-received.

International Nuclear Information System (INIS)

Glow discharge plasma nitriding of AISI 304 austenitic stainless steel has been carried out for different processing time under optimum discharge conditions established by spectroscopic analysis. The treated samples were analysed by X-ray diffraction (XRD) to explore the changes induced in the crystallographic structure. The XRD pattern confirmed the formation of an expanded austenite phase (#gamma#_N) owing to incorporation of nitrogen as an interstitial solid solution in the iron lattice. A Vickers microhardness tester was used to evaluate the surface hardness as a function of indentation depth (#mu#m). The results showed clear evidence of surface changes with substantial increase in surface hardness.

Energy Technology Data Exchange (ETDEWEB)

A full scale experiment was carried out to investigate the texture characteristics of the falling water of free falling and slope failing types. According to the increase of Reynolds number, the texture of falling water was classified into three categories for both types: stability of free surface, transition and whole turbulence. In the first category the stability of the free surface was related to the growth of minute disturbance. Surface tension works as a counter, force to the disturbance in free falling water, and gravity in slope falling water. 14 refs., 15 figs., 3 tabs.

International Nuclear Information System (INIS)

Effect of scale on determination of 12Kh18N10T steel tendency to intergranular corrosion (IGC) by rapid electrochemical techniques in solution of 10 % H_2SO_4+0.0025 g/l KCNS was investigated. It is shown that scale presence of steel surface accelerates anode dissolving, activates grain boundaries. All this results to the effect of tendency to IGC in steels, not inclined to it. The scale is not completely removed from the surface, but remains partially along grain boundaries in result of successive pickling of scale and then a surface layer of metal. This also couses the effect of tendency to IGC.

Energy Technology Data Exchange (ETDEWEB)

In an ideal system the surface of the dish is perfectly parabolic (no contour flaws are present), and the sun rays fall on the dish surface parallel to the focal axis (no sun tracking flaws are present). These two conditions are not realizable in practice; in this case, the parabolic dish system is called real system. In this paper a procedure for analysing the flux distribution on the receiver internal surfaces is presented for a cavity receiver with a real parabolic dish collector. First, the theoretical principles are discussed. Then the effect of the inaccuracy in the collector and in the sun tracking on the insolation pattern is described using an example.

Energy Technology Data Exchange (ETDEWEB)

In this work, the chemical transformations induced by 5 keV protons (10{sup 6} ion cm{sup -2}) at the surface of 0.4 {mu}m polyacrylonitrile and polymethacrylonitrile films are analysed by XPS and IRRAS. Spectroscopic changes in both the polymers are globally similar, the most significant feature being a lower relative concentration of nitrogen with respect to carbon closer to the surface. Quantitatively, this change is more marked in the case of polyacrylonitrile which suggests a direct relation with the hydrogen in {alpha} to the nitrile function.

British Library Electronic Table of Contents (United Kingdom)

In modern quality engineering, dual response surface methodology is a powerful tool to model an industrial process by using both the mean and the standard deviation of the measurements as the responses. The least squares method in regression is often used to estimate the coefficients in the mean and standard deviation models, and various decision criteria are proposed by researchers to find the optimal conditions. Based on the inherent hierarchical structure of the dual response problems, we propose a Bayesian hierarchical approach to model dual response surfaces. Such an approach is compared with two frequentist least squares methods by using two real data sets and simulated data.

Energy Technology Data Exchange (ETDEWEB)

How to decide which mine surface tasks may be performed by industrial robots to improve productivity and working conditions is described. Charts are presented of the industrial tasks performed on the surface and how each task may be classified as light, average, difficult or very diffcult according to a defect criteria is explained (defective operations are those which involve, heavy, harmful, stressful or dangerous jobs). The results of these calculations are used to identify which operations are suitable for first introduction of robots since traditional automation methods cannot be used, e.g. various storage, loading and packaging tasks, coal selection, sorting and removal of foreign matter, provision of services such as food preparation, cleaning, etc. Robots may also be used to control automated operations that are monotonous and hazardous for human operators. It is envisaged that in the future computer programmed robots with artificial ...